WorldWideScience

Sample records for vidicon tubes display

  1. Pulse Characteristic Curves of Vidicons,

    Science.gov (United States)

    microamps, and in vidicons with heterotransition screens, up to 10 microamps. The use of static modulation characteristic curves of vidicons for the...determination of the pulse beam current can lead to an error > 100%. With the help of pulse-modulation characteristic curves, it is possible to obtain the

  2. Landsat 3 return beam vidicon response artifacts

    Science.gov (United States)

    ,; Clark, B.

    1981-01-01

    The return beam vidicon (RBV) sensing systems employed aboard Landsats 1, 2, and 3 have all been similar in that they have utilized vidicon tube cameras. These are not mirror-sweep scanning devices such as the multispectral scanner (MSS) sensors that have also been carried aboard the Landsat satellites. The vidicons operate more like common television cameras, using an electron gun to read images from a photoconductive faceplate.In the case of Landsats 1 and 2, the RBV system consisted of three such vidicons which collected remote sensing data in three distinct spectral bands. Landsat 3, however, utilizes just two vidicon cameras, both of which sense data in a single broad band. The Landsat 3 RBV system additionally has a unique configuration. As arranged, the two cameras can be shuttered alternately, twice each, in the same time it takes for one MSS scene to be acquired. This shuttering sequence results in four RBV "subscenes" for every MSS scene acquired, similar to the four quadrants of a square. See Figure 1. Each subscene represents a ground area of approximately 98 by 98 km. The subscenes are designated A, B, C, and D, for the northwest, northeast, southwest, and southeast quarters of the full scene, respectively. RBV data products are normally ordered, reproduced, and sold on a subscene basis and are in general referred to in this way. Each exposure from the RBV camera system presents an image which is 98 km on a side. When these analog video data are subsequently converted to digital form, the picture element, or pixel, that results is 19 m on a side with an effective resolution element of 30 m. This pixel size is substantially smaller than that obtainable in MSS images (the MSS has an effective resolution element of 73.4 m), and, when RBV images are compared to equivalent MSS images, better resolution in the RBV data is clearly evident. It is for this reason that the RBV system can be a valuable tool for remote sensing of earth resources.Until recently

  3. 21 CFR 870.2450 - Medical cathode-ray tube display.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Medical cathode-ray tube display. 870.2450 Section... cathode-ray tube display. (a) Identification. A medical cathode-ray tube display is a device designed primarily to display selected biological signals. This device often incorporates special display features...

  4. Displays of dabbing marijuana extracts on YouTube.

    Science.gov (United States)

    Krauss, Melissa J; Sowles, Shaina J; Mylvaganam, Shalinee; Zewdie, Kidist; Bierut, Laura J; Cavazos-Rehg, Patricia A

    2015-10-01

    Dabbing involves heating marijuana extracts to a high temperature and inhaling the vapor. Little is known about this new method of using marijuana. YouTube, the most popular platform for sharing online videos, may be a go-to resource for individuals interested in learning about dabbing. Our objective was to explore the content of dabbing-related videos on YouTube. We searched for dabbing-related videos on YouTube using the search terms "dabbing" and "dabs" on January 22, 2015. For each term, videos were sorted by relevance and view count. A sample of 116 dabbing videos were viewed and coded for content. The 116 videos (published by 75 unique channels) had a total of 9,545,482 views. Most (76%) of the channels had a specific focus on marijuana and 23% were located in California. Eighty-nine percent of the videos showed at least one person dabbing, and 61% of these showed someone dabbing repeatedly. Most dabbers were male (67%) and many appeared to be >25 years old (42%). Approximately 34% of the videos contained a product review, 28% provided instructions on dabbing or other educational information, and 21% contained at least a brief cautionary message. Over half (54%) of the videos referenced medical marijuana, and only 20% of the videos had an age-restriction. Dabbing-related videos are easily found and can be readily viewed on YouTube. As marijuana use becomes more accepted by the general population, the popularity of dabbing-related videos could increase, potentially normalizing this potent form of marijuana use. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  5. Landsat 1-2 Return Beam Vidicon Film Only: 1972-1983

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — The three-camera Return Beam Vidicon (RBV) that operated on Landsat satellites 1 and 2 acquired approximately 1600 sub-scenes at 80 meter resolution. The initial RBV...

  6. Displays

    OpenAIRE

    Schauer, A.

    1983-01-01

    A short review is given on new display technologies such as plasma, liquid crystals, light emitting diodes, electroluminescence and electrochromism. It is stated that thin or thick film or hybrid techniques are essential for all the different types of display. Comparing the performance data of displays the advantages, disadvantages, appropriate applications and future developments are described. Finally the display market and its growth are discussed briefly.

  7. Enhancing DC Glow Discharge Tube Museuum Displays using a Theremin Controlled Helmholtz Coil to Demonstrate Magnetic Confinement

    Science.gov (United States)

    Siu, Theodore; Wissel, Stephanie; Guttadora, Larry; Liao, Susan; Zwicker, Andrew

    2010-11-01

    Since their discovery in the mid 1800's, DC glow discharge apparatuses have commonly been used for spectral analysis, the demonstration of the Frank-Hertz experiment, and to study plasma breakdown voltages following from the Paschen Curve. A DC glow discharge tube museum display was outfitted with a Helmholtz Coil electromagnet in order to demonstrate magnetic confinement for a science museum display. A device commonly known as a ``theremin'' was designed and built in order to externally control the Helmholtz Coil current and the plasma current. Originally a musical instrument, a theremin has two variable capacitors connected to two radio frequency oscillators which determine pitch and volume. Using a theremin to control current and ``play'' the plasma adds appeal and durability by providing a new innovative means of interacting with a museum exhibit. Educationally, students can use the display to not only learn about plasma properties but also electronic properties of the human body.

  8. Formation of the color image based on the vidicon TV camera

    Science.gov (United States)

    Iureva, Radda A.; Maltseva, Nadezhda K.; Dunaev, Vadim I.

    2016-09-01

    The main goal of nuclear safety is to protect from accidents in nuclear power plant (NPP) against radiation arising during normal operation of nuclear installations, or as a result of accidents on them. The most important task in any activities aimed at the maintenance of NPP is a constant maintenance of the desired level of security and reliability. The periodic non-destructive testing during operation provides the most relevant criteria for the integrity of the components of the primary circuit pressure. The objective of this study is to develop a system for forming a color image on the television camera on vidicon which is used to conduct non-destructive testing in conditions of increased radiation at NPPs.

  9. Increased micronucleated cell frequency related to exposure to radiation emitted by computer cathode ray tube video display monitors

    Directory of Open Access Journals (Sweden)

    Carbonari Karina

    2005-01-01

    Full Text Available It is well recognized that electromagnetic fields can affect the biological functions of living organisms at both cellular and molecular level. The potential damaging effects of electromagnetic fields and very low frequency and extremely low frequency radiation emitted by computer cathode ray tube video display monitors (VDMs has become a concern within the scientific community. We studied the effects of occupational exposure to VDMs in 10 males and 10 females occupationally exposed to VDMs and 20 unexposed control subjects matched for age and sex. Genetic damage was assessed by examining the frequency of micronuclei in exfoliated buccal cells and the frequency of other nuclear abnormalities such as binucleated and broken egg cells. Although there were no differences regarding binucleated cells between exposed and control individuals our analysis revealed a significantly higher frequency of micronuclei (p < 0.001 and broken egg cells (p < 0.05 in individuals exposed to VDMs as compared to unexposed. We also found that the differences between individuals exposed to VDMs were significantly related to the sex of the individuals and that there was an increase in skin, central nervous system and ocular disease in the exposed individuals. These preliminary results indicate that microcomputer workers exposed to VDMs are at risk of significant cytogenetic damage and should periodically undergo biological monitoring.

  10. A comparison of the suitability of cathode ray tube (CRT) and liquid crystal display (LCD) monitors as visual stimulators in mfERG diagnostics.

    Science.gov (United States)

    Kaltwasser, Christoph; Horn, Folkert K; Kremers, Jan; Juenemann, Anselm

    2009-06-01

    The aim of this study was to determine up to which extent the specific characteristics of cathode ray tube (CRT) and liquid crystal display (LCD) monitors influence the retinal biosignal when used as stimulators in ocular electrophysiology. In a conventional CRT monitor, each pixel lights up only for a duration of a few milliseconds during each frame. In contrast, liquid crystal displays are quasi-static, i.e. each pixel has a constant luminance during the whole length of the frame, but lights up only with a certain delay after the trigger. These different display characteristics may affect the mfERG signal. The temporal and spatial luminance distributions of a CRT and an LCD monitor were measured in white flashes. The total amount of emitted light was calculated by integration of the intensity versus time curves. By means of an mfERG recording system (RETIsystem, Roland Consult, Brandenburg, Germany) first-order kernel (FOK) mfERG signals were computed and then analysed using customized MATLAB (TheMathWorks, Natick, MA, USA) software. With the two stimulator monitors, differences in the mfERG signal were observed. The latencies of mfERG responses recorded with the LCD monitor were significantly increased by 7.1 ms for N1 and 9.5 ms for P1 compared to the CRT. Due to a higher luminance, the N1 amplitude was significantly higher by approx. 2 dB in measurements with the LCD monitor while no significant difference could be detected with regard to the more contrast sensitive P1 amplitude. When using LCD monitors as stimulators the increase in latencies and differences in the luminance versus time profile must be taken into account. Prior to clinical application, the establishment of guidelines for the use of LCD monitors is recommended.

  11. Handbook of display technology

    CERN Document Server

    Castellano, Joseph A

    1992-01-01

    This book presents a comprehensive review of technical and commercial aspects of display technology. It provides design engineers with the information needed to select proper technology for new products. The book focuses on flat, thin displays such as light-emitting diodes, plasma display panels, and liquid crystal displays, but it also includes material on cathode ray tubes. Displays include a large number of products from televisions, auto dashboards, radios, and household appliances, to gasoline pumps, heart monitors, microwave ovens, and more.For more information on display tech

  12. TUBE TESTER

    Science.gov (United States)

    Gittings, H.T. Jr.; Kalbach, J.F.

    1958-01-14

    This patent relates to tube testing, and in particular describes a tube tester for automatic testing of a number of vacuum tubes while in service and as frequently as may be desired. In it broadest aspects the tube tester compares a particular tube with a standard tube tarough a difference amplifier. An unbalanced condition in the circuit of the latter produced by excessive deviation of the tube in its characteristics from standard actuates a switch mechanism stopping the testing cycle and indicating the defective tube.

  13. Auditory Display

    DEFF Research Database (Denmark)

    volume. The conference's topics include auditory exploration of data via sonification and audification; real time monitoring of multivariate date; sound in immersive interfaces and teleoperation; perceptual issues in auditory display; sound in generalized computer interfaces; technologies supporting...... auditory display creation; data handling for auditory display systems; applications of auditory display....

  14. Flaming on YouTube

    NARCIS (Netherlands)

    Moor, Peter J.; Heuvelman, A.; Verleur, R.

    2010-01-01

    In this explorative study, flaming on YouTube was studied using surveys of YouTube users. Flaming is defined as displaying hostility by insulting, swearing or using otherwise offensive language. Three general conclusions were drawn. First, although many users said that they themselves do not flame,

  15. Soft-Copy Reading in Digital Mammography of Microcalcifications: Diagnostic Performance of a 5-Megapixel Cathode Ray Tube Monitor versus a 3-Megapixel Liquid Crystal Display Monitor in a Clinical Setting

    Energy Technology Data Exchange (ETDEWEB)

    Uematsu, T.; Kasami, M.; Uchida, Y. [Dept. of Diagnostic Radiology, Dept. of Pathology, and Breast Center, Shizuoka Cancer Center Hospital, Shizuoka (Japan)

    2007-09-15

    Background: A recent study using dedicated contrast-detail phantoms showed that the image quality of a 3-megapixel (M) monitor can approach that of a 5M monitor in digital mammography. Purpose: To compare a 5M cathode ray tube (CRT) monitor with a 3M liquid crystal display (LCD) monitor for soft-copy reading of digital mammography of microcalcifications in a clinical setting. Material and Methods: 100 screen-detected microcalcification lesions (34 malignant and 66 benign) without mass that had been evaluated with 11-gauge stereotactic vacuum-assisted breast biopsy or definitive surgery were recruited into the study. One radiologist analyzed the soft-copy mammograms on a 5M CRT monitor and a 3M LCD monitor with 5 months between interpretations and scored the likelihood of malignancy and calcification distribution on a five-point scale. Calcification morphology and breast density were scored on a four-point scale. Positive predictive value (PPV) and negative predictive value (NPV) were calculated on the basis of a Breast Imaging Reporting and Data System. The interpretation time was also measured. Results: There was no significant difference in the likelihood of malignancy (P = 0.655), calcification morphology (P = 0.168), calcification distribution (P = 0.11), and breast density (P = 0.0608). The PPV and NPV of soft-copy reading on the 5M CRT monitor was 57% (30/53) and 91% (43/47), respectively, identical to the results using the 3M LCD monitor. The total interpretation time averaged 88 s for the 5M CRT monitor and 67 s for the 3M LCD monitor (P<0.0001). Conclusion: Soft-copy reading of a digital mammography of microcalcifications with a 3M LCD monitor was similar in diagnostic performance to a 5M CRT monitor in this study.

  16. A Comprehensive Process for Display Systems Development.

    Science.gov (United States)

    Simcox, William A.

    A comprehensive development process for display design, focusing on computer-generated cathode ray tube (CRT) displays is presented. A framework is created for breaking the display into its component parts, used to guide the design process. The objective is to design or select the most cost effective graphics solution (hardware and software) to…

  17. Feeding Tubes

    Science.gov (United States)

    ... feeding therapies have been exhausted. Please review product brand and method of placement carefully with your physician ... Total Parenteral Nutrition. Resources: Oley Foundation Feeding Tube Awareness Foundation Children’s Medical Nutrition Alliance APFED’s Educational Webinar ...

  18. Ear Tubes

    Science.gov (United States)

    ... of the ear drum or eustachian tube, Down Syndrome, cleft palate, and barotrauma (injury to the middle ear caused by a reduction of air pressure, ... specialist) may be warranted if you or your child has experienced repeated ... fluid in the middle ear, barotrauma, or have an anatomic abnormality that ...

  19. Neutron tubes

    Science.gov (United States)

    Leung, Ka-Ngo; Lou, Tak Pui; Reijonen, Jani

    2008-03-11

    A neutron tube or generator is based on a RF driven plasma ion source having a quartz or other chamber surrounded by an external RF antenna. A deuterium or mixed deuterium/tritium (or even just a tritium) plasma is generated in the chamber and D or D/T (or T) ions are extracted from the plasma. A neutron generating target is positioned so that the ion beam is incident thereon and loads the target. Incident ions cause D-D or D-T (or T-T) reactions which generate neutrons. Various embodiments differ primarily in size of the chamber and position and shape of the neutron generating target. Some neutron generators are small enough for implantation in the body. The target may be at the end of a catheter-like drift tube. The target may have a tapered or conical surface to increase target surface area.

  20. photomultiplier tube

    CERN Multimedia

    photomultiplier tubes. A device to convert light into an electric signal (the name is often abbreviated to PM). Photomultipliers are used in all detectors based on scintillating material (i.e. based on large numbers of fibres which produce scintillation light at the passage of a charged particle). A photomultiplier consists of 3 main parts: firstly, a photocathode where photons are converted into electrons by the photoelectric effect; secondly, a multiplier chain consisting of a serie of dynodes which multiply the number of electron; finally, an anode, which collects the resulting current.

  1. photomultiplier tubes

    CERN Multimedia

    photomultiplier tubes. A device to convert light into an electric signal (the name is often abbreviated to PM). Photomultipliers are used in all detectors based on scintillating material (i.e. based on large numbers of fibres which produce scintillation light at the passage of a charged particle). A photomultiplier consists of 3 main parts: firstly, a photocathode where photons are converted into electrons by the photoelectric effect; secondly, a multiplier chain consisting of a serie of dynodes which multiply the number of electron; finally, an anode, which collects the resulting current.

  2. Universal Numeric Segmented Display

    OpenAIRE

    Azad, Md. Abul Kalam; Sharmeen, Rezwana; S. M. Kamruzzaman

    2010-01-01

    Segmentation display plays a vital role to display numerals. But in today's world matrix display is also used in displaying numerals. Because numerals has lots of curve edges which is better supported by matrix display. But as matrix display is costly and complex to implement and also needs more memory, segment display is generally used to display numerals. But as there is yet no proposed compact display architecture to display multiple language numerals at a time, this paper proposes uniform...

  3. Optical advantages in retinal scanning displays

    Science.gov (United States)

    Urey, Hakan

    2000-06-01

    Virtual Retinal DisplayTM technology is a retinal scanning display (RSD) technology being developed at Microvision, Inc., for a variety of applications including microdisplays. An RSD scans a modulated light beam onto a viewer's retina to produce a perceived image. Red, green and blue light sources, such as lasers, laser diodes or LEDs combine with Microvision's proprietary miniaturized scanner designs to make the RSD very well suited for head-worn and helmet-mounted displays (HMD). This paper compares the features of RSD technology to other display technologies such as the cathode ray tubes or matrix-based displays for HMD and other wearable display applications, and notes important performance advantages due to the number of pixel- generating elements. Also discussed are some fundamental optical limitations for virtual displays used in the HMD applications.

  4. Neural Tube Defects

    Science.gov (United States)

    ... vitamin, before and during pregnancy prevents most neural tube defects. Neural tube defects are usually diagnosed before the infant is ... or imaging tests. There is no cure for neural tube defects. The nerve damage and loss of function ...

  5. Effects Of Frame Rates In Video Displays

    Science.gov (United States)

    Kellogg, Gary V.; Wagner, Charles A.

    1991-01-01

    Report describes experiment on subjective effects of rates at which display on cathode-ray tube in flight simulator updated and refreshed. Conducted to learn more about jumping, blurring, flickering, and multiple lines that observer perceives when line moves at high speed across screen of a calligraphic CRT.

  6. Nasogastric feeding tube

    Science.gov (United States)

    ... of what to do. What to Expect at Home If your child has an NG tube, try to keep your child from touching or pulling on the tube. After your nurse teaches you how to flush the tube and perform skin care around the nose, set up a daily routine for these tasks. Flushing the Tube Flushing the ...

  7. Plasma Display at the Liberty Science Center

    Science.gov (United States)

    Bruder, Dan; Gilligan, Nick; Tarman, Lisa; Ferris, Pamella; Morgan, James; Delooper, John; Zwicker, Andrew

    2009-11-01

    The Liberty Science Center (LSC) is the largest (300,000 sq. ft.) education resource in the New Jersey -- New York City region. PPPL in collaboration with the LSC has had a display at the center since 2007 More than 1.5 million visitors have come to the museum since the plasma display has been introduced. The plasma display has had significant use during that time frame. During the summer of 2009 a redesigned plasma exhibit was created by a student teacher-team using the lessons learned from the existing exhibit. The display includes a DC glow discharge tube with a permanent external magnet allowing visitors to manipulate the plasma and see how plasma can be used for fusion research. The goal of the display is to allow an individual to see a plasma and understand the potential benefits of fusion energy.

  8. Color Television Projection System Using Three Cathode Ray Tubes.

    Science.gov (United States)

    1982-03-01

    categories, specifically: light valves, scophony , lasers, liquid crystal modulation, and cathode ray tubes. Of these display techniques, the light valves 3...and have comparatively short life times associated with critical components. Both scophony and laser techniques utilize mechanical beam scanning

  9. Improving the computer-human interface: The qualitative monitor display

    Science.gov (United States)

    Baugh, H. W.; Zygielbaum, A. I.

    1982-01-01

    A technique for displaying the information needed by DSN operators for monitoring station performance is described. Known as a 'qualitative monitor,' it presents continuous variables in quasi-analog form on a digital cathode ray tube (CRT) display. Color changes, field reverses and blinking symbols assist the operator in identifying variables that are within acceptable limits and in performing corrective action when needed.

  10. Invisible Display in Aluminum

    DEFF Research Database (Denmark)

    Prichystal, Jan Phuklin; Hansen, Hans Nørgaard; Bladt, Henrik Henriksen

    2005-01-01

    for an integrated display in a metal surface is often ruled by design and functionality of a product. The integration of displays in metal surfaces requires metal removal in order to clear the area of the display to some extent. The idea behind an invisible display in Aluminum concerns the processing of a metal...

  11. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... NEI YouTube Videos > NEI YouTube Videos: Amblyopia NEI YouTube Videos YouTube Videos Home Age-Related Macular Degeneration ... Retinopathy of Prematurity Science Spanish Videos Webinars NEI YouTube Videos: Amblyopia Embedded video for NEI YouTube Videos: ...

  12. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... YouTube Videos > NEI YouTube Videos: Amblyopia NEI YouTube Videos YouTube Videos Home Age-Related Macular Degeneration Amblyopia ... of Prematurity Science Spanish Videos Webinars NEI YouTube Videos: Amblyopia Embedded video for NEI YouTube Videos: Amblyopia ...

  13. NEI You Tube Videos: Amblyopia

    Science.gov (United States)

    ... YouTube Videos > NEI YouTube Videos: Amblyopia NEI YouTube Videos YouTube Videos Home Age-Related Macular Degeneration Amblyopia ... of Prematurity Science Spanish Videos Webinars NEI YouTube Videos: Amblyopia Embedded video for NEI YouTube Videos: Amblyopia ...

  14. Lunar Sample Display Locations

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA provides a number of lunar samples for display at museums, planetariums, and scientific expositions around the world. Lunar displays are open to the public....

  15. A Compressive Superresolution Display

    KAUST Repository

    Heide, Felix

    2014-06-22

    In this paper, we introduce a new compressive display architecture for superresolution image presentation that exploits co-design of the optical device configuration and compressive computation. Our display allows for superresolution, HDR, or glasses-free 3D presentation.

  16. Pulse Tube Refrigerator

    Science.gov (United States)

    Matsubara, Yoichi

    The pulse tube refrigerator is one of the regenerative cycle refrigerators such as Stirling cycle or Gifford-McMahon cycle which gives the cooling temperature below 150 K down to liquid helium temperature. In 1963, W. E. Gifford invented a simple refrigeration cycle which is composed of compressor, regenerator and simple tube named as pulse tube which gives a similar function of the expander in Stirling or Gifford-McMahon cycle. The thermodynamically performance of this pulse tube refrigerator is inferior to that of other regenerative cycles. In 1984, however, Mikulin and coworkers made a significant advance in pulse tube configuration called as orifice pulse tube. After this, several modifications of the pulse tube hot end configuration have been developed. With those modifications, the thermodynamic performance of the pulse tube refrigerator became the same order to that of Stirling and Gifford-McMahon refrigerator. This article reviews the brief history of the pulse tube refrigerator development in the view point of its thermodynamically efficiency. Simplified theories of the energy flow in the pulse tube have also been described.

  17. Categorising YouTube

    DEFF Research Database (Denmark)

    Simonsen, Thomas Mosebo

    2011-01-01

    This article provides a genre analytical approach to creating a typology of the User Generated Content (UGC) of YouTube. The article investigates the construction of navigation processes on the YouTube website. It suggests a pragmatic genre approach that is expanded through a focus on YouTube......’s technological affordances. Through an analysis of the different pragmatic contexts of YouTube, it is argued that a taxonomic understanding of YouTube must be analysed in regards to the vacillation of a user-driven bottom-up folksonomy and a hierarchical browsing system that emphasises a culture of competition...... and which favours the already popular content of YouTube. With this taxonomic approach, the UGC videos are registered and analysed in terms of empirically based observations. The article identifies various UGC categories and their principal characteristics. Furthermore, general tendencies of the UGC within...

  18. Retrograde Gastrojejunostomy Tube Migration

    Directory of Open Access Journals (Sweden)

    Adeleke Adesina

    2014-01-01

    Full Text Available Percutaneous enteral feeding tubes are placed about 250,000 times each year in the United States. Although they are relatively safe, their placement may be complicated by perforation, infection, bleeding, vomiting, dislodgment, and obstruction. There have been numerous reports of antegrade migration of gastrojejunostomy (G-J tubes. We report a case of G-J tube regurgitation following protracted vomiting and discuss the management of this very rare entity.

  19. Heated Tube Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Heated Tube Facility at NASA GRC investigates cooling issues by simulating conditions characteristic of rocket engine thrust chambers and high speed airbreathing...

  20. Steam generator tube failures

    Energy Technology Data Exchange (ETDEWEB)

    MacDonald, P.E.; Shah, V.N.; Ward, L.W.; Ellison, P.G.

    1996-04-01

    A review and summary of the available information on steam generator tubing failures and the impact of these failures on plant safety is presented. The following topics are covered: pressurized water reactor (PWR), Canadian deuterium uranium (CANDU) reactor, and Russian water moderated, water cooled energy reactor (VVER) steam generator degradation, PWR steam generator tube ruptures, the thermal-hydraulic response of a PWR plant with a faulted steam generator, the risk significance of steam generator tube rupture accidents, tubing inspection requirements and fitness-for-service criteria in various countries, and defect detection reliability and sizing accuracy. A significant number of steam generator tubes are defective and are removed from service or repaired each year. This wide spread damage has been caused by many diverse degradation mechanisms, some of which are difficult to detect and predict. In addition, spontaneous tube ruptures have occurred at the rate of about one every 2 years over the last 20 years, and incipient tube ruptures (tube failures usually identified with leak detection monitors just before rupture) have been occurring at the rate of about one per year. These ruptures have caused complex plant transients which have not always been easy for the reactor operators to control. Our analysis shows that if more than 15 tubes rupture during a main steam line break, the system response could lead to core melting. Although spontaneous and induced steam generator tube ruptures are small contributors to the total core damage frequency calculated in probabilistic risk assessments, they are risk significant because the radionuclides are likely to bypass the reactor containment building. The frequency of steam generator tube ruptures can be significantly reduced through appropriate and timely inspections and repairs or removal from service.

  1. Displaying gray shades in liquid crystal displays

    Indian Academy of Sciences (India)

    These transistors act as a switch to charge and hold the desired voltage across a pixel. Passive matrix LCDs are easy to fabricate and cost less as compared to the active matrix LCDs. Current trend demands gray scale and colour capa- bilities even for the displays in mobile phones. Passive matrix LCDs will be preferred as.

  2. Pyrotechnic Tubing Connector

    Science.gov (United States)

    Graves, Thomas J.; Yang, Robert A.

    1988-01-01

    Tool forms mechanical seal at joint without levers or hydraulic apparatus. Proposed tool intended for use in outer space used on Earth by heavily garbed workers to join tubing in difficult environments. Called Pyrotool, used with Lokring (or equivalent) fittings. Piston slides in cylinder when pushed by gas from detonating pyrotechnic charge. Impulse of piston compresses fittings, sealing around butting ends of tubes.

  3. Neural Tube Defects

    Science.gov (United States)

    ... pregnancies each year in the United States. A baby’s neural tube normally develops into the brain and spinal cord. ... fluid in the brain. This is called hydrocephalus. Babies with this condition are treated with surgery to insert a tube (called a shunt) into the brain. The shunt ...

  4. Scalable Resolution Display Walls

    KAUST Repository

    Leigh, Jason

    2013-01-01

    This article will describe the progress since 2000 on research and development in 2-D and 3-D scalable resolution display walls that are built from tiling individual lower resolution flat panel displays. The article will describe approaches and trends in display hardware construction, middleware architecture, and user-interaction design. The article will also highlight examples of use cases and the benefits the technology has brought to their respective disciplines. © 1963-2012 IEEE.

  5. OLED displays and lighting

    CERN Document Server

    Koden, Mitsuhiro

    2017-01-01

    Organic light-emitting diodes (OLEDs) have emerged as the leading technology for the new display and lighting market. OLEDs are solid-state devices composed of thin films of organic molecules that create light with the application of electricity. OLEDs can provide brighter, crisper displays on electronic devices and use less power than conventional light-emitting diodes (LEDs) or liquid crystal displays (LCDs) used today. This book covers both the fundamentals and practical applications of flat and flexible OLEDs.

  6. Matrix display panel based on gas discharge technology

    Science.gov (United States)

    Schiekel, M.; Suessenbach, H.; Schwedes, W.; Keiner, H.; Peppel, G.; Hellwig, W.; Knoll, A.; Rettich, R.; Unbehaun, R.

    1982-03-01

    The components for a slim, gas discharge display panel of stacked tube geometry were developed and characterized for the presentation of color pictures. The technology of pulsed matrix display panels with a four-electrode configuration, having inherent memory, was considered. A breadboard model with maximum panel dimensions of 380 x 250 x 14 cu mm (70,000 pixels) was built. Results show that displays with long positive columns and conically shaped pixels give best brightness and efficiency values. The reliability of such display panels is considerably increased.

  7. Molybdenum Tube Characterization report

    Energy Technology Data Exchange (ETDEWEB)

    Beaux II, Miles Frank [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Usov, Igor Olegovich [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-02-07

    Chemical vapor deposition (CVD) techniques have been utilized to produce free-standing molybdenum tubes with the end goal of nuclear fuel clad applications. In order to produce tubes with properties desirable for this application, deposition rates were lowered requiring long deposition durations on the order of 50 hours. Standard CVD methods as well as fluidized-bed CVD (FBCVD) methods were applied towards these objectives. Characterization of the tubes produced in this manner revealed material suitable for fuel clad applications, but lacking necessary uniformity across the length of the tubes. The production of freestanding Mo tubes that possess the desired properties across their entire length represents an engineering challenge that can be overcome in a next iteration of the deposition system.

  8. Displaying Data As Movies

    Science.gov (United States)

    Moore, Judith G.

    1992-01-01

    NMSB Movie computer program displays large sets of data (more than million individual values). Presentation dynamic, rapidly displaying sequential image "frames" in main "movie" window. Any sequence of two-dimensional sets of data scaled between 0 and 255 (1-byte resolution) displayed as movie. Time- or slice-wise progression of data illustrated. Originally written to present data from three-dimensional ultrasonic scans of damaged aerospace composite materials, illustrates data acquired by thermal-analysis systems measuring rates of heating and cooling of various materials. Developed on Macintosh IIx computer with 8-bit color display adapter and 8 megabytes of memory using Symantec Corporation's Think C, version 4.0.

  9. JAVA Stereo Display Toolkit

    Science.gov (United States)

    Edmonds, Karina

    2008-01-01

    This toolkit provides a common interface for displaying graphical user interface (GUI) components in stereo using either specialized stereo display hardware (e.g., liquid crystal shutter or polarized glasses) or anaglyph display (red/blue glasses) on standard workstation displays. An application using this toolkit will work without modification in either environment, allowing stereo software to reach a wider audience without sacrificing high-quality display on dedicated hardware. The toolkit is written in Java for use with the Swing GUI Toolkit and has cross-platform compatibility. It hooks into the graphics system, allowing any standard Swing component to be displayed in stereo. It uses the OpenGL graphics library to control the stereo hardware and to perform the rendering. It also supports anaglyph and special stereo hardware using the same API (application-program interface), and has the ability to simulate color stereo in anaglyph mode by combining the red band of the left image with the green/blue bands of the right image. This is a low-level toolkit that accomplishes simply the display of components (including the JadeDisplay image display component). It does not include higher-level functions such as disparity adjustment, 3D cursor, or overlays all of which can be built using this toolkit.

  10. Digital Display Integration Project Project Online 2.0

    CERN Document Server

    Bardsley, J N

    1999-01-01

    The electronic display industry is changing in three important ways. First, the dominance of the cathode ray tube (CRT) is being challenged by the development of flat panel displays (FPDs). This will lead to the availability of displays of higher performance, albeit at greater cost. Secondly, the analog interfaces between displays that show data and the computers that generate the data are being replaced by digital connections. Finally, a high-resolution display is becoming the most expensive component in computer system for homes and small offices. It is therefore desirable that the useful lifetime of the display extend over several years and that the electronics allows the display to be used with many different image sources. Hopefully, the necessity of having three or four large CRTs in one office to accommodate different computer operating systems or communication protocols will soon disappear. Instead, we hope to see a set of flat panels that can be switched to show several independent images from multip...

  11. Methodologies for the evaluation of CRT displays

    Energy Technology Data Exchange (ETDEWEB)

    Blackman, H.S.

    1986-01-01

    This paper presents the results of a series of experiments that have been conducted by the Human Factors Research Branch for the purpose of developing objective methods that will be used to evaluate the effectiveness of cathode ray tube (CRT) generated displays in improving reactor operator performance. The results of this work can provide a basis for the United States Nuclear Regulatory Commission (USNRC) to objectively evaluate specific licensee-developed display designs. The following methods have been developed: (1) Psychophysics - short exposure of static display types were presented to subjects who were tasked to report status of a given parameter; (2) Multidimensional Rating Scale - paper and pencil instrument employed by subjects to rate the features of a display type across a variety of psychological dimensions; (3) Checklist Evaluation - a paper and pencil instrument employed by subjects to assess particular display types according to a set of human engineering criteria; (4) Noninteractive Evaluation - a formal experiment where the subjects were requested to identify dynamic simulated transients using various display types; and (5) Interactive Evaluation - similar to the noninteractive, but the subjects interacted with the simulator using a touch screen to mitigate transient events.

  12. Helmet-Mounted Displays (HMD)

    Data.gov (United States)

    Federal Laboratory Consortium — The Helmet-Mounted Display labis responsible for monocular HMD day display evaluations; monocular HMD night vision performance processes; binocular HMD day display...

  13. Effective Monitor Display Design.

    Science.gov (United States)

    Harrell, William

    1999-01-01

    Describes some of the factors that affect computer monitor display design and provides suggestions and insights into how screen displays can be designed more effectively. Topics include color, font choices, organizational structure of text, space outline, and general principles. (Author/LRW)

  14. Jet printing flexible displays

    OpenAIRE

    Street, R. A.; Wong, W S; Ready, S. E.; Chabinyc, M.L; Arias, A.C.; Limb, S.; Salleo, A; Lujan, R.

    2006-01-01

    Jet printing is an interesting patterning technique for electronic devices because it requires no physical mask, has digital control of ejection, and provides good layer-to-layer registration. It also has the potential to reduce display manufacturing costs and enable roll-to-roll processing. The technique is illustrated with examples of prototype printed displays using amorphous silicon and polymer semiconductors.

  15. Standardizing visual display quality

    NARCIS (Netherlands)

    Besuijen, J.; Spenkelink, G.P.J.

    1998-01-01

    The current ISO 9241–3 standard for visual display quality and the proposed user performance tests are reviewed. The standard is found to be more engineering than ergonomic and problems with system configuration, software applications, display settings, user behaviour, wear and physical environment

  16. Visual merchandising window display

    Directory of Open Access Journals (Sweden)

    Opris (Cas. Stanila M.

    2013-12-01

    Full Text Available Window display plays a major part in the selling strategies; it does not only include the simple display of goods, nowadays it is a form of art, also having the purpose of sustaining the brand image. This article wants to reveal the tools that are essential in creating a fabulous window display. Being a window designer is not an easy job, you have to always think ahead trends, to have a sense of colour, to know how to use light to attract customers in the store after only one glance at the window. The big store window displays are theatre scenes: with expensive backgrounds, special effects and high fashion mannequins. The final role of the displays is to convince customers to enter the store and trigger the purchasing act which is the final goal of the retail activity.

  17. Isolated Fallopian Tube Torsion

    Directory of Open Access Journals (Sweden)

    S. Kardakis

    2013-01-01

    Full Text Available Isolated torsion of the Fallopian tube is a rare gynecological cause of acute lower abdominal pain, and diagnosis is difficult. There are no pathognomonic symptoms; clinical, imaging, or laboratory findings. A preoperative ultrasound showing tubular adnexal masses of heterogeneous echogenicity with cystic component is often present. Diagnosis can rarely be made before operation, and laparoscopy is necessary to establish the diagnosis. Unfortunately, surgery often is performed too late for tube conservation. Isolated Fallopian tube torsion should be suspected in case of acute pelvic pain, and prompt intervention is necessary.

  18. Microlaser-based displays

    Science.gov (United States)

    Bergstedt, Robert; Fink, Charles G.; Flint, Graham W.; Hargis, David E.; Peppler, Philipp W.

    1997-07-01

    Laser Power Corporation has developed a new type of projection display, based upon microlaser technology and a novel scan architecture, which provides the foundation for bright, extremely high resolution images. A review of projection technologies is presented along with the limitations of each and the difficulties they experience in trying to generate high resolution imagery. The design of the microlaser based projector is discussed along with the advantage of this technology. High power red, green, and blue microlasers have been designed and developed specifically for use in projection displays. These sources, in combination with high resolution, high contrast modulator, produce a 24 bit color gamut, capable of supporting the full range of real world colors. The new scan architecture, which reduces the modulation rate and scan speeds required, is described. This scan architecture, along with the inherent brightness of the laser provides the fundamentals necessary to produce a 5120 by 4096 resolution display. The brightness and color uniformity of the display is excellent, allowing for tiling of the displays with far fewer artifacts than those in a traditionally tiled display. Applications for the display include simulators, command and control centers, and electronic cinema.

  19. LED-driven backlights for automotive displays

    Science.gov (United States)

    Strauch, Frank

    2007-09-01

    As a light source the LED has some advantage over the traditionally used fluorescence tube such as longer life or lower space consumption. Consequently customers are asking for the LED lighting design in their products. We introduced in a company owned backlight the white LED technology. This step opens the possibility to have access to the components in the display market. Instead of having a finalized display product which needs to be integrated in the head unit of a car we assemble the backlight, the glass, own electronics and the housing. A major advantage of this concept is the better control of the heat flow generated by the LEDs to the outer side because only a common housing is used for all the components. Also the requirement for slim products can be fulfilled. As always a new technology doesn't come with advantages only. An LED represents a point source compared to the well-known tube thus requiring a mixing zone for the multiple point sources when they enter a light guide. This zone can't be used in displays because of the lack of homogeneity. It's a design goal to minimize this zone which can be helped by the right choice of the LED in terms of slimness. A step ahead is the implementation of RGB LEDs because of their higher color rendering abilities. This allows for the control of the chromaticity point under temperature change but as a drawback needs a larger mixing zone.

  20. Tracheostomy tube - eating

    Science.gov (United States)

    Trach - eating ... take your first bites. Certain factors may make eating or swallowing harder, such as: Changes in the ... easier to swallow. Suction the tracheostomy tube before eating. This will keep you from coughing while eating, ...

  1. Bull Moose Tube Company

    Science.gov (United States)

    The EPA is providing notice of a proposed Administrative Penalty Assessment against the Bull Moose Tube Company, a business located at 1819 Clarkson Road, Chesterfield, MO, 63017, for alleged violations at the facility located at 406 East Industrial Drive,

  2. Tube-Forming Assays.

    Science.gov (United States)

    Brown, Ryan M; Meah, Christopher J; Heath, Victoria L; Styles, Iain B; Bicknell, Roy

    2016-01-01

    Angiogenesis involves the generation of new blood vessels from the existing vasculature and is dependent on many growth factors and signaling events. In vivo angiogenesis is dynamic and complex, meaning assays are commonly utilized to explore specific targets for research into this area. Tube-forming assays offer an excellent overview of the molecular processes in angiogenesis. The Matrigel tube forming assay is a simple-to-implement but powerful tool for identifying biomolecules involved in angiogenesis. A detailed experimental protocol on the implementation of the assay is described in conjunction with an in-depth review of methods that can be applied to the analysis of the tube formation. In addition, an ImageJ plug-in is presented which allows automatic quantification of tube images reducing analysis times while removing user bias and subjectivity.

  3. Tube Alinement for Machining

    Science.gov (United States)

    Garcia, J.

    1984-01-01

    Tool with stepped shoulders alines tubes for machining in preparation for welding. Alinement with machine tool axis accurate to within 5 mils (0.13mm) and completed much faster than visual setup by machinist.

  4. Color Display Design Guide

    Science.gov (United States)

    1978-10-01

    and G. M. Corso , "Color flcsearch for Visuz’l Displays, Technical Report No. ONH-CR2l3-102-3, July 1975, 108 pp. 45 1 Results of two code comparison...respective- ly. Since the display elements constitute routine or non-priority informatica , all display information would be coded green if the three-color...1963, with Amendment 1, 30 September 1971. U.S. Government Printing Office: Washington, DC. 27. Christ, R.E. and G.M. Corso . "Color Research for Visual

  5. Small - Display Cartography

    DEFF Research Database (Denmark)

    Nissen, Flemming; Hvas, Anders; Münster-Swendsen, Jørgen

    This report comprises the work carried out in the work-package of small display cartography. The work-package has aimed at creating a general framework for the small-display cartography. A solid framework facilitates an increased use of spatial data in mobile devices - thus enabling, together...... Service Communication and finally, Part IV: Concluding remarks and topics for further research on small-display cartography. Part II includes a separate Appendix D consisting of a cartographic design specification. Part III includes a separate Appendix C consisting of a schema specification, a separate...

  6. Power vacuum tubes handbook

    CERN Document Server

    Whitaker, Jerry

    2012-01-01

    Providing examples of applications, Power Vacuum Tubes Handbook, Third Edition examines the underlying technology of each type of power vacuum tube device in common use today. The author presents basic principles, reports on new development efforts, and discusses implementation and maintenance considerations. Supporting mathematical equations and extensive technical illustrations and schematic diagrams help readers understand the material. Translate Principles into Specific Applications This one-stop reference is a hands-on guide for engineering personnel involved in the design, specification,

  7. Aeronautical tubes and pipes

    Science.gov (United States)

    Beauclair, N.

    1984-12-01

    The main and subcomponent French suppliers of aircraft tubes and pipes are discussed, and the state of the industry is analyzed. Quality control is essential for tubes with regard to their i.d. and metallurgical compositions. French regulations do not allow welded seam tubes in hydraulic circuits unless no other form is available, and then rustproofed steel must be installed. The actual low level of orders for any run of tubes dictates that the product is only one of several among the manufacturers' line. Automation, both in NDT and quality control, assures that the tubes meet specifications. A total of 10 French companies participate in the industry, serving both civil and military needs, with some companies specializing only in titanium, steel, or aluminum materials. Concerns wishing to enter the market must upgrade their equipment to meet the higher aeronautical specifications and be prepared to furnish tubes and pipes that serve both functional and structural purposes simultaneously. Additionally, pipe-bending machines must also perform to tight specifications. Pipes can range from 0.2 mm exterior diameter to 40 mm, with wall thicknesses from 0.02 mm to 3 mm. A chart containing a list of manufacturers and their respective specifications and characteristics is presented, and a downtrend in production with reduction of personnel is noted.

  8. Spherical tube hypersurfaces

    CERN Document Server

    Isaev, Alexander

    2011-01-01

    We examine Levi non-degenerate tube hypersurfaces in complex linear space which are "spherical," that is, locally CR-equivalent to the real hyperquadric. Spherical hypersurfaces are characterized by the condition of the vanishing of the CR-curvature form, so such hypersurfaces are flat from the CR-geometric viewpoint. On the other hand, such hypersurfaces are also of interest from the point of view of affine geometry. Thus our treatment of spherical tube hypersurfaces in this book is two-fold: CR-geometric and affine-geometric. As the book shows, spherical tube hypersurfaces possess remarkable properties. For example, every such hypersurface is real-analytic and extends to a closed real-analytic spherical tube hypersurface in complex space. One of our main goals is to provide an explicit affine classification of closed spherical tube hypersurfaces whenever possible. In this book we offer a comprehensive exposition of the theory of spherical tube hypersurfaces, starting with the idea proposed in the pioneering...

  9. Map display design

    Science.gov (United States)

    Aretz, Anthony J.

    1990-01-01

    This paper presents a cognitive model of a pilot's navigation task and describes an experiment comparing a visual momentum map display to the traditional track-up and north-up approaches. The data show the advantage to a track-up map is its congruence with the ego-centered forward view; however, the development of survey knowledge is hindered by the inconsistency of the rotating display. The stable alignment of a north-up map aids the acquisition of survey knowledge, but there is a cost associated with the mental rotation of the display to a track-up alignment for ego-centered tasks. The results also show that visual momentum can be used to reduce the mental rotation costs of a north-up display.

  10. Compressive light field displays.

    Science.gov (United States)

    Wetzstein, Gordon; Lanman, Douglas; Hirsch, Matthew; Heidrich, Wolfgang; Raskar, Ramesh

    2012-01-01

    Light fields are the multiview extension of stereo image pairs: a collection of images showing a 3D scene from slightly different perspectives. Depicting high-resolution light fields usually requires an excessively large display bandwidth; compressive light field displays are enabled by the codesign of optical elements and computational-processing algorithms. Rather than pursuing a direct "optical" solution (for example, adding one more pixel to support the emission of one additional light ray), compressive displays aim to create flexible optical systems that can synthesize a compressed target light field. In effect, each pixel emits a superposition of light rays. Through compression and tailored optical designs, fewer display pixels are necessary to emit a given light field than a direct optical solution would require.

  11. Flexible displays, rigid designs?

    DEFF Research Database (Denmark)

    Hornbæk, Kasper

    2015-01-01

    Rapid technological progress has enabled a wide range of flexible displays for computing devices, but the user experience--which we're only beginning to understand--will be the key driver for successful designs....

  12. ENERGY STAR Certified Displays

    Data.gov (United States)

    U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 7.0 ENERGY STAR Program Requirements for Displays that are effective as of July 1, 2016....

  13. Advanced aerosense display interfaces

    Science.gov (United States)

    Hopper, Darrel G.; Meyer, Frederick M.

    1998-09-01

    High-resolution display technologies are being developed to meet the ever-increasing demand for realistic detail. The requirement for evermore visual information exceeds the capacity of fielded aerospace display interfaces. In this paper we begin an exploration of display interfaces and evolving aerospace requirements. Current and evolving standards for avionics, commercial, and flat panel displays are summarized and compared to near term goals for military and aerospace applications. Aerospace and military applications prior to 2005 up to UXGA and digital HDTV resolution can be met by using commercial interface standard developments. Advanced aerospace requirements require yet higher resolutions (2560 X 2048 color pixels, 5120 X 4096 color pixels at 85 Hz, etc.) and necessitate the initiation of discussion herein of an 'ultra digital interface standard (UDIS)' which includes 'smart interface' features such as large memory and blazingly fast resizing microcomputer. Interface capacity, IT, increased about 105 from 1973 to 1998; 102 more is needed for UDIS.

  14. Liquid Crystal Airborne Display

    Science.gov (United States)

    1977-08-01

    with the drive capability of the present state-of-the- art microm.ziiaturized integi ated circuits. The impact of microminiaturizing the drive circuits...7 Advantages /Disadvantages of Prior Art .........- 8 Performance of the Liquid Crystal Matrix Display . . .. 8 Liquid Crystal...Holographic HUD Light Source ...................... .... 99 Design of a Special Purpose Mercury Art - Plo.?hcr La np . 104 V LARGE SCALE INTEGRATION FOR DISPLAY

  15. Military display performance parameters

    Science.gov (United States)

    Desjardins, Daniel D.; Meyer, Frederick

    2012-06-01

    The military display market is analyzed in terms of four of its segments: avionics, vetronics, dismounted soldier, and command and control. Requirements are summarized for a number of technology-driving parameters, to include luminance, night vision imaging system compatibility, gray levels, resolution, dimming range, viewing angle, video capability, altitude, temperature, shock and vibration, etc., for direct-view and virtual-view displays in cockpits and crew stations. Technical specifications are discussed for selected programs.

  16. ORFeome Phage Display.

    Science.gov (United States)

    Zantow, Jonas; Moreira, Gustavo Marçal Schmidt Garcia; Dübel, Stefan; Hust, Michael

    2018-01-01

    ORFeome phage display allows the efficient functional screening of entire proteomes or even metaproteomes to identify immunogenic proteins. For this purpose, randomly fragmented, whole genomes or metagenomes are cloned into a phage-display vector allowing positive selection for open reading frames (ORF) to improve the library quality. These libraries display all possible proteins encoded by a pathogen or a microbiome on the phage surface. Consequently, immunogenic proteins can be selected from these libraries using disease-related immunoglobulins from patient serum. ORFeome phage display in particular allows the identification of immunogenic proteins that are only expressed in the host-pathogen interaction but not in cultivation, as well as the detection of very low expressed and very small immunogens and immunogenic proteins of non-cultivable organisms. The identified immunogenic proteins are potential biomarkers for the development of diagnostic assays or vaccines. These articles will give an introduction to ORFeome phage-display technology and give detailed protocols to identify immunogenic proteins by phage display.

  17. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... search for current job openings visit HHS USAJobs Home > NEI YouTube Videos > NEI YouTube Videos: Amblyopia NEI YouTube Videos YouTube Videos Home Age-Related Macular Degeneration Amblyopia Animations Blindness Cataract ...

  18. Gastrostomy feeding tube - pump - child

    Science.gov (United States)

    ... tube feeding; PEG tube care; Feeding - gastrostomy tube - pump; G-tube - pump; Gastrostomy button - pump; Bard Button - pump; MIC-KEY - pump ... Gather supplies: Feeding pump (electronic or battery powered) Feeding ... pump (includes a feeding bag, drip chamber, roller clamp, ...

  19. Performance and Preference with Various VDT (Video Display Terminal) Phosphors

    Science.gov (United States)

    1987-04-24

    Studies 14:215-223. Santucci, G., Menu , J.P., and Valot, C. (1982). Visual acuity in color contrast on cathode ray tubes: role of luminance, hue, and...Van Nes, F.L. (1986). Space, colour and typography on visual display terminals. Behav. and Info, Tech. 5: 99-118. Van Nes, F.L. and Bouman, M.A. (1967

  20. Human Visual Performance and Flat Panel Display Image Quality

    Science.gov (United States)

    1980-07-01

    adequately han- dled, can cause burn -in nonuniformities.) In matrix addressed AC thin film displays, densities of 4.9/mm cc.n easily be achieved, and...PM TUBE N i i PHOTOMETER AMHLINtK in i n r^ s% SCANNING EYEPIECE ♦ POWER SUPPLY ’GO’ SWITCH Figure 128: Schematic of photometer

  1. Information rich display design

    Energy Technology Data Exchange (ETDEWEB)

    Welch, Robin; Braseth, Alf Ove; Veland, Oeystein

    2004-07-01

    This paper presents the concept Information Rich Displays. The purpose of Information Rich Displays (IRDs) is to condensate prevailing information in process displays in such a way that each display format (picture) contains more relevant information for the user. Compared to traditional process control displays, this new concept allows the operator to attain key information at a glance and at the same time allows for improved monitoring of larger portions of the process. This again allows for reduced navigation between both process and trend displays and ease the cognitive demand on the operator. This concept has been created while working on designing display prototypes for the offshore petroleum production facilities of tomorrow. Offshore installations basically consist of wells, separation trains (where oil, gas and water are separated from each other), an oil tax measurement system (where oil quality is measured and the pressure increased to allow for export), gas compression (compression of gas for export) and utility systems (water treatment, chemical systems etc.). This means that an offshore control room operator has to deal with a complex process that comprises several functionally different systems. The need for a new approach to offshore display format design is in particular based on shortcomings in today's designs related to the keyhole effect, where the display format only reveals a fraction of the whole process. Furthermore, the upcoming introduction of larger off- and on-shore operation centres will increase the size and complexity of the operators' work domain. In the light of the increased demands on the operator, the proposed IRDs aim to counter the negative effects this may have on the workload. In this work we have attempted to classify the wide range of different roles an operator can have in different situations. The information content and amount being presented to the operator in a display should be viewed in context of the roles

  2. Categorising YouTube

    Directory of Open Access Journals (Sweden)

    Thomas Mosebo Simonsen

    2011-09-01

    Full Text Available This article provides a genre analytical approach to creating a typology of the User Generated Content (UGC of YouTube. The article investigates the construction of navigationprocesses on the YouTube website. It suggests a pragmatic genre approach that is expanded through a focus on YouTube’s technological affordances. Through an analysis of the different pragmatic contexts of YouTube, it is argued that a taxonomic understanding of YouTube must be analysed in regards to the vacillation of a user-driven bottom-up folksonomy and a hierarchical browsing system that emphasises a culture of competition and which favours the already popular content of YouTube. With this taxonomic approach, the UGC videos are registered and analysed in terms of empirically based observations. The article identifies various UGC categories and their principal characteristics. Furthermore, general tendencies of the UGC within the interacting relationship of new and old genres are discussed. It is argued that the utility of a conventional categorical system is primarily of analytical and theoretical interest rather than as a practical instrument.

  3. Geiger-Muller tubes

    Energy Technology Data Exchange (ETDEWEB)

    Gair, S.A.; Copleston, R.E.

    1991-01-16

    A Geiger-Muller tube designed for use in an environment (for example, mounted on a rock drill) where subjected to mechanical shock and vibration has a tensioned anode wire secured by welding to securement members between first and second mounts at opposite ends of the tube envelope. The wire tension is adjusted to a high value with a screwable-adjustment means which is locked eg. by a spot-weld or by a locking nut, in the adjusted position, so that the natural frequency of the vibration of the tensioned wire does not resonate with (and may be much higher than) the frequencies to which the tube is subjected in use. The wire frequency is typically in excess of 400Hz and even 500Hz. The adjustment means may be included in the mount via which the envelope is evacuated and back-filled with the ionizible gas, and a gas-tight seal can be provided around this part of the mount, for example by sealing off the gas pump tube. However the adjustment means may be designed into another part of the tube, for example using telescopic parts of the envelope whose sliding junction is made gas tight with a flexible seal. (author).

  4. Dynamic plasmonic colour display

    Science.gov (United States)

    Duan, Xiaoyang; Kamin, Simon; Liu, Na

    2017-01-01

    Plasmonic colour printing based on engineered metasurfaces has revolutionized colour display science due to its unprecedented subwavelength resolution and high-density optical data storage. However, advanced plasmonic displays with novel functionalities including dynamic multicolour printing, animations, and highly secure encryption have remained in their infancy. Here we demonstrate a dynamic plasmonic colour display technique that enables all the aforementioned functionalities using catalytic magnesium metasurfaces. Controlled hydrogenation and dehydrogenation of the constituent magnesium nanoparticles, which serve as dynamic pixels, allow for plasmonic colour printing, tuning, erasing and restoration of colour. Different dynamic pixels feature distinct colour transformation kinetics, enabling plasmonic animations. Through smart material processing, information encoded on selected pixels, which are indiscernible to both optical and scanning electron microscopies, can only be read out using hydrogen as a decoding key, suggesting a new generation of information encryption and anti-counterfeiting applications. PMID:28232722

  5. Stereo Painting Display Devices

    Science.gov (United States)

    Shafer, David

    1982-06-01

    The Spanish Surrealist artist Salvador Dali has recently perfected the art of producing two paintings which are stereo pairs. Each painting is separately quite remarkable, presenting a subject with the vivid realism and clarity for which Dali is famous. Due to the surrealistic themes of Dali's art, however, the subjects preser.ted with such naturalism only exist in his imagination. Despite this considerable obstacle to producing stereo art, Dali has managed to paint stereo pairs that display subtle differences of coloring and lighting, in addition to the essential perspective differences. These stereo paintings require a display method that will allow the viewer to experience stereo fusion, but which will not degrade the high quality of the art work. This paper gives a review of several display methods that seem promising in terms of economy, size, adjustability, and image quality.

  6. Military display market: update to fourth comprehensive edition

    Science.gov (United States)

    Desjardins, Daniel D.; Byrd, James C.; Hopper, Darrel G.

    2009-05-01

    The military display market is analyzed in terms of all fully electronic and many electro-mechanical displays used on combat platforms across all DOD Services. The military market for displays is defined by parameters such as active area, bezel-to-bezel measurement and technology. Other characteristics such as luminance, contrast ratio, gray levels, resolution, viewing angle, color, video capability, and night vision imaging system compatibility are noted. This study takes into account all displays that are either installed or funded for installation. In some cases, planned displays are also included. Display sizes having aggregate defense applications of 5,000 units or greater and having DOD applications across 10 or more platform fleets, are tabulated. The issue of size commonality is addressed where distribution of active area across platform fleets, individually, in groups of two through nine, and ten or more, is illustrated. Military displays are also analyzed by technology, where total quantities of such displays are broken out into CRT, LCD, AMLCD, EM, LED, Incandescent, Plasma and TFEL percentages. Custom, versus rugged commercial, versus commercial off-the-shelf designs are contrasted. High and low information content designs are identified. Displays for several high-profile military programs are discussed, to include both technical specifications and program history. This defense-wide study, an up-date to our paper delivered April 2006, documents 642 weapons system platforms comprising 1,194,199 displays in 1,217 sizes, of which 1,197 are direct-view and 20 are virtual-view. Defense display sizes range from 0.082 in..2 to 10,625 in.2 in 18 technologies, mostly flat panel display (FPD) technologies based on thin-film transistor active matrix liquid crystal displays (TFT AM LCD), with cathode ray tube (CRT) second and dropping rapidly. This paper provides an overview of the DOD display market, allowing government, academia and industry highlights of

  7. Refreshing Refreshable Braille Displays.

    Science.gov (United States)

    Russomanno, Alexander; O'Modhrain, Sile; Gillespie, R Brent; Rodger, Matthew W M

    2015-01-01

    The increased access to books afforded to blind people via e-publishing has given them long-sought independence for both recreational and educational reading. In most cases, blind readers access materials using speech output. For some content such as highly technical texts, music, and graphics, speech is not an appropriate access modality as it does not promote deep understanding. Therefore blind braille readers often prefer electronic braille displays. But, these are prohibitively expensive. The search is on, therefore, for a low-cost refreshable display that would go beyond current technologies and deliver graphical content as well as text. And many solutions have been proposed, some of which reduce costs by restricting the number of characters that can be displayed, even down to a single braille cell. In this paper, we demonstrate that restricting tactile cues during braille reading leads to poorer performance in a letter recognition task. In particular, we show that lack of sliding contact between the fingertip and the braille reading surface results in more errors and that the number of errors increases as a function of presentation speed. These findings suggest that single cell displays which do not incorporate sliding contact are likely to be less effective for braille reading.

  8. Tube Map Interface for a Coupled Scheduling and Diagnostics System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose the concept of a tube map display as a means to effectively integrate schedule timeline information and fault diagnosis data into a single high value...

  9. CONTEMPLATE ON PSYCHOLOGICAL BUYING BEHAVIOUR OF Gen Z CONSUMERS TOWARDS YOU TUBE ADVERTISEMENTS

    OpenAIRE

    Dr. G. Jayanthi; S. Sarathampal

    2017-01-01

    The study is about the psychological buying behaviour of consumers towards YouTube advertisements. Advertisements play an important role to create awareness among people about the product or service. Earlier advertisements were shown and displayed on television, radio, and newspaper but today’s digital media have replaced and conquered the old form of advertisements. In digital media YouTube has become a common platform for advertisements. While watching YouTube, we often come across pre-roll...

  10. A New Resonance Tube

    Science.gov (United States)

    Bates, Alan

    2017-01-01

    The measurement of the speed of sound in air with the resonance tube is a popular experiment that often yields accurate results. One approach is to hold a vibrating tuning fork over an air column that is partially immersed in water. The column is raised and lowered in the water until the generated standing wave produces resonance: this occurs at…

  11. Cladding tube manufacturing technology

    Energy Technology Data Exchange (ETDEWEB)

    Hahn, R. [Kraftwerk Union AG, Mulheim (Germany); Jeong, Y.H.; Baek, B.J.; Kim, K.H.; Kim, S.J.; Choi, B.K.; Kim, J.M. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1999-04-01

    This report gives an overview of the manufacturing routine of PWR cladding tubes. The routine essentially consists of a series of deformation and annealing processes which are necessary to transform the ingot geometry to tube dimensions. By changing shape, microstructure and structure-related properties are altered simultaneously. First, a short overview of the basics of that part of deformation geometry is given which is related to tube reducing operations. Then those processes of the manufacturing routine which change the microstructure are depicted, and the influence of certain process parameters on microstructure and material properties are shown. The influence of the resulting microstructure on material properties is not discussed in detail, since it is described in my previous report 'Alloy Development for High Burnup Cladding.' Because of their paramount importance still up to now, and because manufacturing data and their influence on properties for other alloys are not so well established or published, the descriptions are mostly related to Zry4 tube manufacturing, and are only in short for other alloys. (author). 9 refs., 46 figs.

  12. Jejunostomy feeding tube

    Science.gov (United States)

    ... skin for redness, odor, pain, puss, or swelling. Make sure the stitches are still in place. Use the clean towel or Q-tip to clean the skin around the J-tube 1 to 3 times a day with mild soap and water. Try to remove any drainage or crusting on ...

  13. Color television system using single gun color cathode ray tube

    Science.gov (United States)

    Gaiser, E. E.; Hilborn, E. H.

    1970-01-01

    Two-primary color and single gun system provides quality differential color and variation in brightness for specific colors by varying current and controlling duty cycle of electron beam. Number of video amplifiers, deflection circuits, and guns required to display color TV picture is reduced and less complex tube is required.

  14. Drift tubes of Linac 2

    CERN Multimedia

    Photographic Service

    1977-01-01

    Being redied for installation, those at the right are for tank 1, those on the left for tank 2. Contrary to Linac 1, which had drift-tubes supported on stems, here the tubes are suspended, for better mechanical stability.

  15. Refrigerated display cabinets; Butikskyla

    Energy Technology Data Exchange (ETDEWEB)

    Fahlen, Per

    2000-07-01

    This report summarizes experience from SP research and assignments regarding refrigerated transport and storage of food, mainly in the retail sector. It presents the fundamentals of heat and mass transfer in display cabinets with special focus on indirect systems and secondary refrigerants. Moreover, the report includes a brief account of basic food hygiene and the related regulations. The material has been compiled for educational purposes in the Masters program at Chalmers Technical University.

  16. Tactical Video Display.

    Science.gov (United States)

    1981-02-01

    designed to extend the state-of-the-art in the area of thin film electroluminescent display systems. The program entails two major areas of efforts...the inclusion of the residual gases in thin film is very likely and dependent upon the concentrations of the gases and the reactive nature of the...reproducible films . Some exploratory work was also performed on the feasitility of applying a ZnTe /Te system black layer with TFEL structure. Pre

  17. Attention-Seeking Displays.

    Directory of Open Access Journals (Sweden)

    Szabolcs Számadó

    Full Text Available Animal communication abounds with extravagant displays. These signals are usually interpreted as costly signals of quality. However, there is another important function for these signals: to call the attention of the receiver to the signaller. While there is abundant empirical evidence to show the importance of this stage, it is not yet incorporated into standard signalling theory. Here I investigate a general model of signalling - based on a basic action-response game - that incorporates this searching stage. I show that giving attention-seeking displays and searching for them can be an ESS. This is a very general result and holds regardless whether only the high quality signallers or both high and low types give them. These signals need not be costly at the equilibrium and they need not be honest signals of any quality, as their function is not to signal quality but simply to call the attention of the potential receivers. These kind of displays are probably more common than their current weight in the literature would suggest.

  18. Stage Cylindrical Immersive Display

    Science.gov (United States)

    Abramyan, Lucy; Norris, Jeffrey S.; Powell, Mark W.; Mittman, David S.; Shams, Khawaja S.

    2011-01-01

    Panoramic images with a wide field of view intend to provide a better understanding of an environment by placing objects of the environment on one seamless image. However, understanding the sizes and relative positions of the objects in a panorama is not intuitive and prone to errors because the field of view is unnatural to human perception. Scientists are often faced with the difficult task of interpreting the sizes and relative positions of objects in an environment when viewing an image of the environment on computer monitors or prints. A panorama can display an object that appears to be to the right of the viewer when it is, in fact, behind the viewer. This misinterpretation can be very costly, especially when the environment is remote and/or only accessible by unmanned vehicles. A 270 cylindrical display has been developed that surrounds the viewer with carefully calibrated panoramic imagery that correctly engages their natural kinesthetic senses and provides a more accurate awareness of the environment. The cylindrical immersive display offers a more natural window to the environment than a standard cubic CAVE (Cave Automatic Virtual Environment), and the geometry allows multiple collocated users to simultaneously view data and share important decision-making tasks. A CAVE is an immersive virtual reality environment that allows one or more users to absorb themselves in a virtual environment. A common CAVE setup is a room-sized cube where the cube sides act as projection planes. By nature, all cubic CAVEs face a problem with edge matching at edges and corners of the display. Modern immersive displays have found ways to minimize seams by creating very tight edges, and rely on the user to ignore the seam. One significant deficiency of flat-walled CAVEs is that the sense of orientation and perspective within the scene is broken across adjacent walls. On any single wall, parallel lines properly converge at their vanishing point as they should, and the sense of

  19. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... NEI YouTube Videos: Amblyopia NEI YouTube Videos YouTube Videos Home Age-Related Macular Degeneration Amblyopia Animations Blindness Cataract Convergence Insufficiency Diabetic Eye Disease Dilated Eye Exam Dry Eye For Kids Glaucoma ...

  20. Enteral Tube Feeding and Pneumonia

    Science.gov (United States)

    Gray, David Sheridan; Kimmel, David

    2006-01-01

    To determine the effects of enteral tube feeding on the incidence of pneumonia, we performed a retrospective review of all clients at our institution who had gastrostomy or jejunostomy tubes placed over a 10-year period. Ninety-three subjects had a history of pneumonia before feeding tube insertion. Eighty had gastrostomy and 13, jejunostomy…

  1. Three-in-one resonance tube for harmonic series sound wave experiments

    Science.gov (United States)

    Jaafar, Rosly; Nazihah Mat Daud, Anis; Ali, Shaharudin; Kadri Ayop, Shahrul

    2017-07-01

    In this study we constructed a special three-in-one resonance tube for a harmonic series sound waves experiment. It is designed for three different experiments: both-open-end, one-closed-end and both-closed-end tubes. The resonance tube consists of a PVC conduit with a rectangular hole, rubber tube, plastic stopper with an embedded microphone and a plastic stopper. The resonance tube is utilized with visual analyser freeware to detect, display and measure the resonance frequencies for each harmonic series. The speeds of sound in air, v, are determined from the gradient of the 2(L+e) versus n fn-1 , 4(L+e) versus n fn-1 and 2L versus n fn-1 graphs for both-open-end, one-closed-end and both-closed-end tubes, respectively. The compatibility of a resonance tube for a harmonic series experiment is determined by comparing the experimental and standard values of v. The use of a resonance tube produces accurate results for v within a 1.91% error compared to its standard value. It can also be used to determine the values of end correction, e, in both-open-end and one-closed-end tubes. The special resonance tube can also be used for the values of n for a harmonic series experiment in the three types of resonance tubes: both-open-end, one-closed-end and both-closed-end tubes.

  2. Handbook of Visual Display Technology

    CERN Document Server

    Cranton, Wayne; Fihn, Mark

    2012-01-01

    The Handbook of Visual Display Technology is a unique work offering a comprehensive description of the science, technology, economic and human interface factors associated with the displays industry. An invaluable compilation of information, the Handbook will serve as a single reference source with expert contributions from over 150 international display professionals and academic researchers. All classes of display device are covered including LCDs, reflective displays, flexible solutions and emissive devices such as OLEDs and plasma displays, with discussion of established principles, emergent technologies, and particular areas of application. The wide-ranging content also encompasses the fundamental science of light and vision, image manipulation, core materials and processing techniques, display driving and metrology.

  3. Vortex tube optimization theory

    Energy Technology Data Exchange (ETDEWEB)

    Lewins, Jeffery [Cambridge Univ., Magdalene Coll., Cambridge (United Kingdom); Bejan, Adrian [Duke Univ., Dept. of Mechanical Engineering and Materials Science, Durham, NC (United States)

    1999-11-01

    The Ranque-Hilsch vortex tube splits a single high pressure stream of gas into cold and warm streams. Simple models for the vortex tube combined with regenerative precooling are given from which an optimisation can be undertaken. Two such optimisations are needed: the first shows that at any given cut or fraction of the cold stream, the best refrigerative load, allowing for the temperature lift, is nearly half the maximum loading that would result in no lift. The second optimisation shows that the optimum cut is an equal division of the vortex streams between hot and cold. Bounds are obtainable within this theory for the performance of the system for a given gas and pressure ratio. (Author)

  4. YouTube Physics

    Science.gov (United States)

    Riendeau, Diane

    2012-09-01

    To date, this column has presented videos to show in class, Don Mathieson from Tulsa Community College suggested that YouTube could be used in another fashion. In Don's experience, his students are not always prepared for the mathematic rigor of his course. Even at the high school level, math can be a barrier for physics students. Walid Shihabi, a colleague of Don's, decided to compile a list of YouTube videos that his students could watch to relearn basic mathematics. I thought this sounded like a fantastic idea and a great service to the students. Walid graciously agreed to share his list and I have reproduced a large portion of it below.

  5. Neural tube defects

    Directory of Open Access Journals (Sweden)

    M.E. Marshall

    1981-09-01

    Full Text Available Neural tube defects refer to any defect in the morphogenesis of the neural tube, the most common types being spina bifida and anencephaly. Spina bifida has been recognised in skeletons found in north-eastern Morocco and estimated to have an age of almost 12 000 years. It was also known to the ancient Greek and Arabian physicians who thought that the bony defect was due to the tumour. The term spina bifida was first used by Professor Nicolai Tulp of Amsterdam in 1652. Many other terms have been used to describe this defect, but spina bifida remains the most useful general term, as it describes the separation of the vertebral elements in the midline.

  6. Diffusion in Tube Dialyzer

    Directory of Open Access Journals (Sweden)

    Yohannes Nigatie

    2017-09-01

    Full Text Available Nowadays, kidney failure is a problem of many peoples in the world. We know that the main function of kidney is maintaining the chemical quality of blood particularly removing urea through urine. But when they malfunction, the pathologic state known as uremia results in a condition in which the urea is retained in the body. Failure of the kidney results in building up of harmful wastes and excess fluids in the body. Kidney diseases (failures can be due to infections, high blood pressure (hypertension, diabetes, and/or extensive use of medication. The best form of treatment is the implantation of a healthy kidney from a donor. However, this is often not possible due to the limited availability of human organs. Chronic kidney failure requires the treatment using a tube dialyzer called dialysis. Blood is taken out of the body and passes through a special membrane that removes waste and extra fluids. The clean blood is then returned to the body. The process is controlled by a dialysis machine (tube dialyzer which is equipped with a blood pump and monitoring systems to ensure safety. So this article investigates the real application of mathematics (diffusion in medical science, and it also contains the mathematical formulation and interpretation of tube dialyzer in relation to diffusion.

  7. Image Descriptors for Displays

    Science.gov (United States)

    1977-02-01

    the entire display could be changed as often as every 1/60 s (TV field rate). Scan interlace was not used on the monitor. The 1/60-s resolution of...of photons arriving at the retina. These contributions can be separated by examining the experimental mT(v) as a function of luminance. From... photon shot noise, was found to be negligible for luminance .al.•- above 4 iabout 10 mL. Thus, the function A(v) represents the m4(v) employed in the

  8. Reliability of steam generator tubing

    Energy Technology Data Exchange (ETDEWEB)

    Kadokami, E. [Mitsubishi Heavy Industries Ltd., Hyogo-ku (Japan)

    1997-02-01

    The author presents results on studies made of the reliability of steam generator (SG) tubing. The basis for this work is that in Japan the issue of defects in SG tubing is addressed by the approach that any detected defect should be repaired, either by plugging the tube or sleeving it. However, this leaves open the issue that there is a detection limit in practice, and what is the effect of nondetectable cracks on the performance of tubing. These studies were commissioned to look at the safety issues involved in degraded SG tubing. The program has looked at a number of different issues. First was an assessment of the penetration and opening behavior of tube flaws due to internal pressure in the tubing. They have studied: penetration behavior of the tube flaws; primary water leakage from through-wall flaws; opening behavior of through-wall flaws. In addition they have looked at the question of the reliability of tubing with flaws during normal plant operation. Also there have been studies done on the consequences of tube rupture accidents on the integrity of neighboring tubes.

  9. Painting Reproductions on Display

    Directory of Open Access Journals (Sweden)

    Joanna Iranowska

    2017-09-01

    Full Text Available Paintings in museums might occasionally be replaced by a photoprint mimicking the original. This article is an investigation of what constitutes a good reproduction of an artwork (oil painting that is meant to be displayed. The article discusses what the usefulness of reproductions depends on, applying the Valuation Studies approach, which means the primary concern is with the practice of valuing itself. In other words, the study focuses on how museum experts evaluate reproduc-tions of oil paintings. The article analyses three cases of displaying digitally prin-ted copies of Edvard Munch's oil paintings between 2013 and 2015 in the Munch Museum and in the National Gallery in Oslo. The study is based on a series of semi-structured interviews with the experts, working at and for the museums, that were involved in producing and exhibiting of the photoprints: curators, con-servators, museum educators, and external manufacturers. The interviews were grouped into five clusters, which I have chosen to call registers of valuing following Frank Heuts and Annemarie Mol (2013. The described valuation practices have to do with delivering experiences to the public, obtaining mimetic resemblance, solving ethical aspects, exhibitions' budget, and last but not least, with the time perspective.

  10. Determining minimal display element requirements for surface map displays

    Science.gov (United States)

    2003-04-14

    There is a great deal of interest in developing electronic surface map displays to enhance safety and reduce incidents and incursions on or near the airport surface. There is a lack of research, however, detailing the minimal display elements require...

  11. Three beam-combining schemes in a color projection display

    Science.gov (United States)

    Scholl, Marija S.

    1987-01-01

    Several beam-combining schemes for on-axis and off-axis optical system layout are presented. The on-axis approaches include two crossed plates with dichroic coatings placed at 90 deg, with respect to each other, and a pentaprism arrangement. The off-axis layout of the cathode ray tubes requires that the images be combined at the display screen. These image-combining approaches are compared for the standard television rates of 525 lines and the high-resolution television at 1200/2000 lines under development in Japan. It is concluded that, for the high-performance, high-color fidelity, and high-resolution projection systems, which are expected to fit into a small volume of space such as a Space Station display or a cockpit panoramic display, a folded configuration with either crossed plates or pentaprism plates will result in an optimum color display.

  12. Third-Generation Display Technology: Nominally Transparent Material

    Directory of Open Access Journals (Sweden)

    Charles Willow

    2010-12-01

    Full Text Available Display technology is reshaping the consumer, business, government, and even not-for-profit markets in the midst of the digital convergence, coupled with recent smart phones led by Apple, Inc. First-Generation (1G display technology was dominated by the Cathode Ray Tubes, followed by Liquid Crystal Display and Plasma in 2G. A radically innovative shift as a disruptive technology is expected to follow in 3G to utilize virtually any transparent material, which wirelessly connects to portable access points. This paper studies the feasibility of the 3G Display Technology (DT with Technology S-Curves, and presents possible business models and technology strategies which may be generated from it. Additional subsets of business models may be derived for a wide range of industry applications.

  13. An expert display system and nuclear power plant control rooms

    Science.gov (United States)

    Beltracchi, L.

    1988-04-01

    General topics for consideration when designing expert display systems and nuclear power plant control room displays are summarized. A system is proposed in which the display of segments (a combined series of graphic primitives or a reusable collection of graphic primitives and primitives attributes stored in memory) controls a cathode-ray-tube's screen to form an image of plant operations. The image consists of an icon of: (1) the process (heat engine cycle), (2) plant control systems, and (3) safety systems. A set of data-driven, forward-chaining computer-stored rules control the display segments. As plant operation changes, measured plant data are processed through the rules, and the results control the deletion and addition of segments to the display format. The icon contains information needed by control rooms operators to monitor plant operations. One example of an expert display is illustrated for the operator's task of monitoring leakage from a safety valve in a steam line of a boiling water reactor (BWR). In another example, the use of an expert display to monitor plant operations during pre-trip, trip, and post-trip operations is discussed as a universal display.

  14. A Well Tempered Mammographic Display

    National Research Council Canada - National Science Library

    Kundel, Harold L

    1997-01-01

    This proposal addresses the development of a softcopy display for digital mammography that seeks to couple optimally the visual system to the displayed image without excessive human-machine interaction...

  15. Optimal delivery in display advertising

    OpenAIRE

    Mostagir, Mohamed

    2010-01-01

    In display advertising, a publisher targets a specific audience by displaying ads on content web pages. Because the publisher has little control over the supply of display opportunities, the actual supply of ads that it can sell is stochastic. We consider the problem of optimal ad delivery, where an advertiser requests a certain number of impressions to be displayed by the publisher over a certain time horizon. Time is divided into periods, and in the beginning of each period the publisher ch...

  16. Steam generator tube integrity program

    Energy Technology Data Exchange (ETDEWEB)

    Dierks, D.R.; Shack, W.J. [Argonne National Laboratory, IL (United States); Muscara, J.

    1996-03-01

    A new research program on steam generator tubing degradation is being sponsored by the U.S. Nuclear Regulatory Commission (NRC) at Argonne National Laboratory. This program is intended to support a performance-based steam generator tube integrity rule. Critical areas addressed by the program include evaluation of the processes used for the in-service inspection of steam generator tubes and recommendations for improving the reliability and accuracy of inspections; validation and improvement of correlations for evaluating integrity and leakage of degraded steam generator tubes, and validation and improvement of correlations and models for predicting degradation in steam generator tubes as aging occurs. The studies will focus on mill-annealed Alloy 600 tubing, however, tests will also be performed on replacement materials such as thermally-treated Alloy 600 or 690. An overview of the technical work planned for the program is given.

  17. Diffusion in a Curved Tube

    OpenAIRE

    Ogawa, Naohisa

    2011-01-01

    The diffusion of particles in confining walls forming a tube is discussed. Such a transport phenomenon is observed in biological cells and porous media. We consider the case in which the tube is winding with curvature and torsion, and the thickness of the tube is sufficiently small compared with its curvature radius. We discuss how geomerical quantities appear in a quasi-one-dimensional diffusion equation.

  18. Alternate tube plugging criteria for steam generator tubes

    Energy Technology Data Exchange (ETDEWEB)

    Cueto-Felgueroso, C.; Aparicio, C.B. [Tecnatom, S.A., Madrid (Spain)

    1997-02-01

    The tubing of the Steam Generators constitutes more than half of the reactor coolant pressure boundary. Specific requirements governing the maintenance of steam generator tubes integrity are set in Plant Technical Specifications and in Section XI of the ASME Boiler and Pressure Vessel Code. The operating experience of Steam Generator tubes of PWR plants has shown the existence of some types of degradatory processes. Every one of these has an specific cause and affects one or more zones of the tubes. In the case of Spanish Power Plants, and depending on the particular Plant considered, they should be mentioned the Primary Water Stress Corrosion Cracking (PWSCC) at the roll transition zone (RTZ), the Outside Diameter Stress Corrosion Cracking (ODSCC) at the Tube Support Plate (TSP) intersections and the fretting with the Anti-Vibration Bars (AVBs) or with the Support Plates in the preheater zone. The In-Service Inspections by Eddy Currents constitutes the standard method for assuring the SG tubes integrity and they permit the monitoring of the defects during the service life of the plant. When the degradation reaches a determined limit, called the plugging limit, the SG tube must be either repaired or retired from service by plugging. Customarily, the plugging limit is related to the depth of the defect. Such depth is typically 40% of the wall thickness of the tube and is applicable to any type of defect in the tube. In its origin, that limit was established for tubes thinned by wastage, which was the predominant degradation in the seventies. The application of this criterion for axial crack-like defects, as, for instance, those due to PWSCC in the roll transition zone, has lead to an excessive and unnecessary number of tubes being plugged. This has lead to the development of defect specific plugging criteria. Examples of the application of such criteria are discussed in the article.

  19. YouTube and 'psychiatry'.

    Science.gov (United States)

    Gordon, Robert; Miller, John; Collins, Noel

    2015-12-01

    YouTube is a video-sharing website that is increasingly used to share and disseminate health-related information, particularly among younger people. There are reports that social media sites, such as YouTube, are being used to communicate an anti-psychiatry message but this has never been confirmed in any published analysis of YouTube clip content. This descriptive study revealed that the representation of 'psychiatry' during summer 2012 was predominantly negative. A subsequent smaller re-analysis suggests that the negative portrayal of 'psychiatry' on YouTube is a stable phenomenon. The significance of this and how it could be addressed are discussed.

  20. Bacterial Biofilms in Jones Tubes.

    Science.gov (United States)

    Ahn, Eric S; Hauck, Matthew J; Kirk Harris, Jonathan; Robertson, Charles E; Dailey, Roger A

    To investigate the presence and microbiology of bacterial biofilms on Jones tubes (JTs) by direct visualization with scanning electron microscopy and polymerase chain reaction (PCR) of representative JTs, and to correlate these findings with inflammation and/or infection related to the JT. In this study, prospective case series were performed. JTs were recovered from consecutive patients presenting to clinic for routine cleaning or recurrent irritation/infection. Four tubes were processed for scanning electron microscopy alone to visualize evidence of biofilms. Two tubes underwent PCR alone for bacterial quantification. One tube was divided in half and sent for scanning electron microscopy and PCR. Symptoms related to the JTs were recorded at the time of recovery. Seven tubes were obtained. Five underwent SEM, and 3 out of 5 showed evidence of biofilms (60%). Two of the 3 biofilms demonstrated cocci and the third revealed rods. Three tubes underwent PCR. The predominant bacteria identified were Pseudomonadales (39%), Pseudomonas (16%), and Staphylococcus (14%). Three of the 7 patients (43%) reported irritation and discharge at presentation. Two symptomatic patients, whose tubes were imaged only, revealed biofilms. The third symptomatic patient's tube underwent PCR only, showing predominantly Staphylococcus (56%) and Haemophilus (36%) species. Two of the 4 asymptomatic patients also showed biofilms. All symptomatic patients improved rapidly after tube exchange and steroid antibiotic drops. Bacterial biofilms were variably present on JTs, and did not always correlate with patients' symptoms. Nevertheless, routine JT cleaning is recommended to treat and possibly prevent inflammation caused by biofilms.

  1. LHCb Event display

    CERN Document Server

    Trisovic, Ana

    2014-01-01

    The LHCb Event Display was made for educational purposes at the European Organization for Nuclear Research, CERN in Geneva, Switzerland. The project was implemented as a stand-alone application using C++ and ROOT, a framework developed by CERN for data analysis. This paper outlines the development and architecture of the application in detail, as well as the motivation for the development and the goals of the exercise. The application focuses on the visualization of events recorded by the LHCb detector, where an event represents a set of charged particle tracks in one proton-proton collision. Every particle track is coloured by its type and can be selected to see its essential information such as mass and momentum. The application allows students to save this information and calculate the invariant mass for any pair of particles. Furthermore, the students can use additional calculating tools in the application and build up a histogram of these invariant masses. The goal for the students is to find a $D^0$ par...

  2. Colorimetry for CRT displays.

    Science.gov (United States)

    Golz, Jürgen; MacLeod, Donald I A

    2003-05-01

    We analyze the sources of error in specifying color in CRT displays. These include errors inherent in the use of the color matching functions of the CIE 1931 standard observer when only colorimetric, not radiometric, calibrations are available. We provide transformation coefficients that prove to correct the deficiencies of this observer very well. We consider four different candidate sets of cone sensitivities. Some of these differ substantially; variation among candidate cone sensitivities exceeds the variation among phosphors. Finally, the effects of the recognized forms of observer variation on the visual responses (cone excitations or cone contrasts) generated by CRT stimuli are investigated and quantitatively specified. Cone pigment polymorphism gives rise to variation of a few per cent in relative excitation by the different phosphors--a variation larger than the errors ensuing from the adoption of the CIE standard observer, though smaller than the differences between some candidate cone sensitivities. Macular pigmentation has a larger influence, affecting mainly responses to the blue phosphor. The estimated combined effect of all sources of observer variation is comparable in magnitude with the largest differences between competing cone sensitivity estimates but is not enough to disrupt very seriously the relation between the L and M cone weights and the isoluminance settings of individual observers. It is also comparable with typical instrumental colorimetric errors, but we discuss these only briefly.

  3. Learning from YouTube [Video Book

    Science.gov (United States)

    Juhasz, Alexandra

    2011-01-01

    YouTube is a mess. YouTube is for amateurs. YouTube dissolves the real. YouTube is host to inconceivable combos. YouTube is best for corporate-made community. YouTube is badly baked. These are a few of the things Media Studies professor Alexandra Juhasz (and her class) learned about YouTube when she set out to investigate what actually happens…

  4. Infrared imaging of LED lighting tubes and fluorescent tubes

    Science.gov (United States)

    Siikanen, Sami; Kivi, Sini; Kauppinen, Timo; Juuti, Mikko

    2011-05-01

    The low energy efficiency of conventional light sources is mainly caused by generation of waste heat. We used infrared (IR) imaging in order to monitor the heating of both LED tube luminaires and ordinary T8 fluorescent tubes. The IR images showed clearly how the surface temperatures of the fluorescent tube ends quickly rose up to about +50...+70°C, whereas the highest surface temperatures seen on the LED tubes were only about +30...+40°C. The IR images demonstrated how the heat produced by the individual LED chips can be efficiently guided to the supporting structure in order to keep the LED emitters cool and hence maintain efficient operation. The consumed electrical power and produced illuminance were also recorded during 24 hour measurements. In order to assess the total luminous efficacy of the luminaires, separate luminous flux measurements were made in a large integrating sphere. The currently available LED tubes showed efficacies of up to 88 lm/W, whereas a standard "cool white" T8 fluorescent tube produced ca. 75 lm/W. Both lamp types gave ca. 110 - 130 lx right below the ceiling-mounted luminaire, but the LED tubes consume only 40 - 55% of the electric power compared to fluorescent tubes.

  5. Drop tube technical tasks

    Science.gov (United States)

    Workman, G. L.

    1986-01-01

    Criteria, using fundamental thermochemical dynamics, were developed to assist a scientist using the Drop Tube Facility in designing a good experiment. The types of parameters involved in designing the experiments include the type of furnace, the type of atmosphere, and in general which materials are better behaved than others as determined by past experience in the facility. One of the major advantages of the facility lies in its ability to provide large undercoolings in the cooling curve during the drops. A beginning was to consider the effect of oxygen and other gases upon the amount of undercooling observed. The starting point of the thermochemistry was given by Ellingham and later transformed into what is known as the Richardson Chart. The effect of surface oxidations upon the nucleation phenomena can be observed in each specimen.

  6. Nasoenteric tube complications.

    Science.gov (United States)

    Prabhakaran, S; Doraiswamy, V A; Nagaraja, V; Cipolla, J; Ofurum, U; Evans, D C; Lindsey, D E; Seamon, M J; Kavuturu, S; Gerlach, A T; Jaik, N P; Eiferman, D S; Papadimos, T J; Adolph, M D; Cook, C H; Stawicki, S P A

    2012-01-01

    The use of nasoenteric tubes (NETs) is ubiquitous, and clinicians often take their placement, function, and maintenance for granted. NETs are used for gastrointestinal decompression, enteral feeding, medication administration, naso-biliary drainage, and specialized indications such as upper gastrointestinal bleeding. Morbidity associated with NETs is common, but frequently subtle, mandating high index of suspicion, clinical vigilance, and patient safety protocols. Common complications include sinusitis, sore throat and epistaxis. More serious complications include luminal perforation, pulmonary injury, aspiration, and intracranial placement. Frequent monitoring and continual re-review of the indications for continued use of any NET is prudent, including consideration of changing goals of care. This manuscript reviews NET-related complications and associated topics.

  7. Piezoelectric Rotary Tube Motor

    Science.gov (United States)

    Fisher, Charles D.; Badescu, Mircea; Braun, David F.; Culhane, Robert

    2011-01-01

    A custom rotary SQUIGGLE(Registered TradeMark) motor has been developed that sets new benchmarks for small motor size, high position resolution, and high torque without gear reduction. Its capabilities cannot be achieved with conventional electromagnetic motors. It consists of piezoelectric plates mounted on a square flexible tube. The plates are actuated via voltage waveforms 90 out of phase at the resonant frequency of the device to create rotary motion. The motors were incorporated into a two-axis postioner that was designed for fiber-fed spectroscopy for ground-based and space-based projects. The positioner enables large-scale celestial object surveys to take place in a practical amount of time.

  8. E-2D Advanced Hawkeye: primary flight display

    Science.gov (United States)

    Paolillo, Paul W.; Saxena, Ragini; Garruba, Jonathan; Tripathi, Sanjay; Blanchard, Randy

    2006-05-01

    This paper is a response to the challenge of providing a large area avionics display for the E-2D AHE aircraft. The resulting display design provides a pilot with high-resolution visual information content covering an image area of almost three square feet (Active Area of Samsung display = 33.792cm x 27.0336 cm = 13.304" x 10.643" = 141.596 square inches = 0.983 sq. ft x 3 = 2.95 sq. ft). The avionics display application, design and performance being described is the Primary Flight Display for the E-2D Advanced Hawkeye aircraft. This cockpit display has a screen diagonal size of 17 inches. Three displays, with minimum bezel width, just fit within the available instrument panel area. The significant design constraints of supporting an upgrade installation have been addressed. These constraints include a display image size that is larger than the mounting opening in the instrument panel. This, therefore, requires that the Electromagnetic Interference (EMI) window, LCD panel and backlight all fit within the limited available bezel depth. High brightness and a wide dimming range are supported with a dual mode Cold Cathode Fluorescent Tube (CCFT) and LED backlight. Packaging constraints dictated the use of multiple U shaped fluorescent lamps in a direct view backlight design for a maximum display brightness of 300 foot-Lamberts. The low intensity backlight levels are provided by remote LEDs coupled through a fiber optic mesh. This architecture generates luminous uniformity within a minimum backlight depth. Cross-cockpit viewing is supported with ultra-wide field-of-view performance including contrast and the color stability of an advanced LCD cell design supports. Display system design tradeoffs directed a priority to high optical efficiency for minimum power and weight.

  9. Augmenting digital displays with computation

    Science.gov (United States)

    Liu, Jing

    As we inevitably step deeper and deeper into a world connected via the Internet, more and more information will be exchanged digitally. Displays are the interface between digital information and each individual. Naturally, one fundamental goal of displays is to reproduce information as realistically as possible since humans still care a lot about what happens in the real world. Human eyes are the receiving end of such information exchange; therefore it is impossible to study displays without studying the human visual system. In fact, the design of displays is rather closely coupled with what human eyes are capable of perceiving. For example, we are less interested in building displays that emit light in the invisible spectrum. This dissertation explores how we can augment displays with computation, which takes both display hardware and the human visual system into consideration. Four novel projects on display technologies are included in this dissertation: First, we propose a software-based approach to driving multiview autostereoscopic displays. Our display algorithm can dynamically assign views to hardware display zones based on multiple observers' current head positions, substantially reducing crosstalk and stereo inversion. Second, we present a dense projector array that creates a seamless 3D viewing experience for multiple viewers. We smoothly interpolate the set of viewer heights and distances on a per-vertex basis across the arrays field of view, reducing image distortion, crosstalk, and artifacts from tracking errors. Third, we propose a method for high dynamic range display calibration that takes into account the variation of the chrominance error over luminance. We propose a data structure for enabling efficient representation and querying of the calibration function, which also allows user-guided balancing between memory consumption and the amount of computation. Fourth, we present user studies that demonstrate that the ˜ 60 Hz critical flicker fusion

  10. PACS displays: how to select the right display technology.

    Science.gov (United States)

    Hirschorn, David S; Krupinski, Elizabeth A; Flynn, Michael J

    2014-12-01

    The medical imaging display is a precision instrument with many features not found in commercial-grade displays. The more one understands what these features are and their corresponding clinical value, the better one can make a purchase decision. None of these displays maintain themselves for 5 years or more without some degree of automatic or manual performance testing. Routine calibration conformance checks are beginning to be mandated by the departments of health of many states. Most manufacturers provide mechanisms to perform these checks and keep track of their results, some more easily than others. A consistent display brightness of about 400 cd/m(2) and close conformance to the DICOM curve are the key components of a successful check. Displays are typically characterized by the number of pixels they contain, usually 2, 3, or 5 megapixels, but this is the least useful determinant of image quality. What matters most is the size of the pixels and the size of the whole display, which should be selected on the basis of the typical viewing distance. The farther one's eyes are from the display, the larger the pixels and the overall display size can be while still feeding the eye as much information as it can see. Care should be taken to use the appropriate display in a given setting for the clinical purpose at hand. Copyright © 2014 American College of Radiology. Published by Elsevier Inc. All rights reserved.

  11. Enteral tube feeding in adults.

    Science.gov (United States)

    Scott, R; Bowling, T E

    2015-03-01

    Enteral tube feeding is usually a relatively straightforward method of nutritional support, and should be facilitated by a multiprofessional team. For short-term use (tube is indicated but if longer term feeding is required then a gastrostomy is appropriate, usually inserted endoscopically (a percutaneous endoscopic gastrostomy tube). The most common serious complication of a nasogastric tube is not identifying a misplaced tube within the lungs: there are clear recommendations from the National Patient Safety Agency as to how to check tube placement. Nasojejunal tubes are required in patients with gastroparesis. Tube blockage is common and is prevented by careful and regular flushing. Diarrhoea is the most complication of feeding and is often related to other medication. Clinicians need an algorithm for systematically dealing with such a problem. Refeeding syndrome may occur in malnourished patients and is characterised by low levels of potassium, phosphate, and/or magnesium, as well as disorders of water and salt balance. Identifying the at-risk patient with careful monitoring is crucial.

  12. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... Amaurosis Low Vision Refractive Errors Retinopathy of Prematurity Science Spanish Videos Webinars NEI YouTube Videos: Amblyopia Embedded video for NEI YouTube Videos: Amblyopia NEI Home Contact Us A-Z Site Map NEI on Social Media Information in Spanish (Información en español) Website, ...

  13. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... National Eye Institute’s mission is to “conduct and support research, training, health information dissemination, and other programs ... search for current job openings visit HHS USAJobs Home > NEI YouTube Videos > NEI YouTube Videos: Amblyopia NEI ...

  14. 27 CFR 40.352 - Cigarette tubes.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Cigarette tubes. 40.352... OF THE TREASURY (CONTINUED) TOBACCO MANUFACTURE OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Manufacture of Cigarette Papers and Tubes Taxes § 40.352 Cigarette tubes. Cigarette tubes...

  15. Drug administration via nasogastric tube.

    Science.gov (United States)

    Clarke, Sonya

    2008-09-01

    In 2005, the National Patient Safety Agency (NPSA) highlighted concerns about the management of nasogastric tubes following reports of unnecessary deaths because of misplaced feeding tubes in infants, children and adults. During 2006, I investigated the management of nasogastric tubes (NGTs) in children (Clarke and Richardson 2007a, 2007b). This systematic review divided primary papers into three principal themes: enteral feeding via the NGT; confirmation of NGT position and associated incidence of tube placement error; and hydration via the NGT for acute gastroenteritis in children. Findings of the review are summarised here in relation to using the nasogastric tube to administer medication to children with the aim of informing practice and improving safety.

  16. Prototyping user displays using CLIPS

    Science.gov (United States)

    Kosta, Charles P.; Miller, Ross; Krolak, Patrick; Vesty, Matt

    1990-01-01

    CLIPS is being used as an integral module of a rapid prototyping system. The prototyping system consists of a display manager for object browsing, a graph program for displaying line and bar charts, and a communications server for routing messages between modules. A CLIPS simulation of a physical model provides dynamic control of the user's display. Currently, a project is well underway to prototype the Advanced Automation System (AAS) for the Federal Aviation Administration.

  17. Texture-based correspondence display

    Science.gov (United States)

    Gerald-Yamasaki, Michael

    2005-03-01

    Texture-based correspondence display is a methodology to display corresponding data elements in visual representations of complex multidimensional, multivariate data. Texture is utilized as a persistent medium to contain a visual representation model and as a means to create multiple renditions of data where color is used to identify correspondence. Corresponding data elements are displayed over a variety of visual metaphors in a normal rendering process without adding extraneous linking metadata creation and maintenance. Texture-based correspondence display extends the effectiveness of visual representation for understanding data to the understanding and creation of visual representation models.

  18. Integrated micromachined scanning display systems

    Science.gov (United States)

    Hagelin, Paul M.; Krishnamoorthy, Uma; Conant, Robert A.; Muller, Richard S.; Lau, Kam Y.; Solgaard, Olav

    1999-07-01

    We describe a raster-scanning display system comprised of two tilt-up micromachined polysilicon mirrors that rotate about orthogonal axes. We have demonstrated a resolution of 102 X 119 pixels. The optical efficiency of our two- mirror micro-optical raster-scanning system is comparable to that of micromachined display systems developed by Texas Instruments and Silicon Light Machines. Ease of integration with on-chip light sources and lenses has the potential to reduce packaging size, complexity and cost of the display system and makes it well suited for head-mounted display applications.

  19. Eddy current signal comparison for tube identification

    Science.gov (United States)

    Glass, S. W.; Vojvodic, R.

    2015-03-01

    Inspection of nuclear power plant steam generator tubes is required to justify continued safe plant operation. The steam generators consist of thousands of tubes with nominal diameters of 15 to 22mm, approximately 1mm wall thickness, and 20 to 30m in length. The tubes are inspected by passing an eddy current probe through the tubes from tube end to tube end. It is critical to know exactly which tube identification (row and column) is associated with each tube's data. This is controlled by a precision manipulator that provides the tube ID to the eddy current system. Historically there have been some instances where the manipulator incorrectly reported the tube ID. This can have serious consequences including lack of inspection of a tube, or if a pluggable indication is detected, the tube is likely to be mis-plugged thereby risking a primary to secondary leak.

  20. Water-storage-tube systems. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hemker, P.

    1981-12-24

    Passive solar collection/storage/distribution systems were surveyed, designed, fabricated, and mechanically and thermally tested. The types studied were clear and opaque fiberglass tubes, metal tubes with plastic liners, and thermosyphoning tubes. (MHR)

  1. Advanced Transport Operating System (ATOPS) color displays software description: MicroVAX system

    Science.gov (United States)

    Slominski, Christopher J.; Plyler, Valerie E.; Dickson, Richard W.

    1992-01-01

    This document describes the software created for the Display MicroVAX computer used for the Advanced Transport Operating Systems (ATOPS) project on the Transport Systems Research Vehicle (TSRV). The software delivery of February 27, 1991, known as the 'baseline display system', is the one described in this document. Throughout this publication, module descriptions are presented in a standardized format which contains module purpose, calling sequence, detailed description, and global references. The global references section includes subroutines, functions, and common variables referenced by a particular module. The system described supports the Research Flight Deck (RFD) of the TSRV. The RFD contains eight Cathode Ray Tubes (CRTs) which depict a Primary Flight Display, Navigation Display, System Warning Display, Takeoff Performance Monitoring System Display, and Engine Display.

  2. Advanced Transport Operating System (ATOPS) color displays software description microprocessor system

    Science.gov (United States)

    Slominski, Christopher J.; Plyler, Valerie E.; Dickson, Richard W.

    1992-01-01

    This document describes the software created for the Sperry Microprocessor Color Display System used for the Advanced Transport Operating Systems (ATOPS) project on the Transport Systems Research Vehicle (TSRV). The software delivery known as the 'baseline display system', is the one described in this document. Throughout this publication, module descriptions are presented in a standardized format which contains module purpose, calling sequence, detailed description, and global references. The global reference section includes procedures and common variables referenced by a particular module. The system described supports the Research Flight Deck (RFD) of the TSRV. The RFD contains eight cathode ray tubes (CRTs) which depict a Primary Flight Display, Navigation Display, System Warning Display, Takeoff Performance Monitoring System Display, and Engine Display.

  3. Flux tubes at finite temperature

    Energy Technology Data Exchange (ETDEWEB)

    Cea, Paolo [INFN, Sezione di Bari,Via G. Amendola 173, I-70126 Bari (Italy); Dipartimento di Fisica dell’Università di Bari,Via G. Amendola 173, I-70126 Bari (Italy); Cosmai, Leonardo [INFN, Sezione di Bari,Via G. Amendola 173, I-70126 Bari (Italy); Cuteri, Francesca; Papa, Alessandro [Dipartimento di Fisica, Università della Calabria & INFN-Cosenza,Ponte Bucci, cubo 31C, I-87036 Rende (Cosenza) (Italy)

    2016-06-07

    The chromoelectric field generated by a static quark-antiquark pair, with its peculiar tube-like shape, can be nicely described, at zero temperature, within the dual superconductor scenario for the QCD confining vacuum. In this work we investigate, by lattice Monte Carlo simulations of the SU(3) pure gauge theory, the fate of chromoelectric flux tubes across the deconfinement transition. We find that, if the distance between the static sources is kept fixed at about 0.76 fm ≃1.6/√σ and the temperature is increased towards and above the deconfinement temperature T{sub c}, the amplitude of the field inside the flux tube gets smaller, while the shape of the flux tube does not vary appreciably across deconfinement. This scenario with flux-tube “evaporation” above T{sub c} has no correspondence in ordinary (type-II) superconductivity, where instead the transition to the phase with normal conductivity is characterized by a divergent fattening of flux tubes as the transition temperature is approached from below. We present also some evidence about the existence of flux-tube structures in the magnetic sector of the theory in the deconfined phase.

  4. Method of making straight fuel cell tubes

    Science.gov (United States)

    Borglum, Brian P.

    2001-01-01

    A method and an apparatus for making straight fuel cell tubes are disclosed. Extruded tubes comprising powders of fuel cell material and a solvent are dried by rotating the extruded tubes. The rotation process provides uniform circumferential drying which results in uniform linear shrinkage of the tubes. The resultant dried tubes are very straight, thereby eliminating subsequent straightening steps required with conventional processes. The method is particularly useful for forming inner air electrode tubes of solid oxide fuel cells.

  5. Counteracting the Influence of Peer Smoking on YouTube.

    Science.gov (United States)

    Romer, Daniel; Jamieson, Patrick E; Jamieson, Kathleen Hall; Jones, Christopher; Sherr, Susan

    2017-04-01

    YouTube, a popular online site for user-generated content, is emerging as a powerful source of peer modeling of smoking. Previous research suggests that in counteracting such influence, health messages may inadvertently increase the perceived prevalence of drug use (a descriptive norm) without reducing its acceptability (injunctive norm). This research tested the ability of health messages to reduce the social acceptability of peer smoking on YouTube despite enhancing its perceived prevalence. In an online experiment with 999 adolescents, participants were randomly assigned to view one of two videos: (a) a mosaic displaying a variety of YouTube videos of adolescents smoking followed by a message about the mortality risk to those smokers, or (b) a control video on a health topic unrelated to smoking. Although exposure to the adolescent YouTube smokers increased perceived prevalence among some participants, it simultaneously increased beliefs about smoking's adverse health outcomes and negative attitudes toward smoking, effects that were associated with reductions in injunctive norms of social acceptability. Interventions that communicate the severity and scope of health risks associated with smoking may undercut the descriptive normative effects of peer modeling of smoking on social media sites such as YouTube.

  6. PEG tubes: dealing with complications.

    Science.gov (United States)

    Malhi, Hardip; Thompson, Rosie

    A percutaneous endoscopic gastronomy tube can be used to deliver nutrition, hydration and medicines directly into the patient's stomach. Patients will require a tube if they are unable to swallow safely, putting them at risk of aspiration of food, drink and medicines into their lungs. It is vital that nurses are aware of the complications that may arise when caring for a patient with a PEG tube. It is equally important that nurses know how to deal with these complications or from where tc seek advice. This article provides a quick troubleshooting guide to help nurses deal with complications that can arise with PEG feeding.

  7. Glass Tube Design for CRT(Cathode Ray Tube)

    OpenAIRE

    Junko, ITOH; Keizo, KISHIDA; Koji, NAKAMURA; Masayuki, Miyazaki; Shigeo, OHSUGI; Sumio, YOSHIOKA; Department of Precision Science & Technology, Osaka University; Mitsubishi Elec.Corp.

    2000-01-01

    Stress and deformation of cathode ray tubes(CRTs)under atmospheric pressure and implosion protection band tightening were analyzed using a finite element method(FEM). The stress and deformation of the tubes were measured experimentally by using strain gages and three-dimensional position measuring techniques. The experimental results showed close agreements with those of the simulation. The location of the highest tensile stress and the effects of tightening of the implosion protection bands ...

  8. Display Technology: An Annotated Bibliography.

    Science.gov (United States)

    1973-12-01

    cockpit displays in future aircraft may be radically different from the present arrays of separate, single-purpose instruments. Many display ca - pabilities...Interna- tional Air Transport Association 15th Technical Conference, Lucerne , Switzer- land, April 1963. Engineering Paper No. 1583, Douglas Aircraft

  9. Cognitive Considerations in Display Design.

    Science.gov (United States)

    Simcox, William

    This investigation of the encoding features of graphs begins with a description of a cognitive framework which allows designers to factor into the process of designing displays how people interpret the information found and what display properties are responsible for this interpretation. The framework also provides a performance measure for use in…

  10. Flexible Bistable Cholesteric Reflective Displays

    Science.gov (United States)

    Yang, Deng-Ke

    2006-03-01

    Cholesteric liquid crystals (ChLCs) exhibit two stable states at zero field condition-the reflecting planar state and the nonreflecting focal conic state. ChLCs are an excellent candidate for inexpensive and rugged electronic books and papers. This paper will review the display cell structure,materials and drive schemes for flexible bistable cholesteric (Ch) reflective displays.

  11. Real Image Visual Display System

    Science.gov (United States)

    1992-12-01

    Vol. 1457 Stereoscopic Displays and Applications 11, 274-282 (February 1991). 15. Lucente, Marc . "Optimization of Hologram Computaion for Real-Time Dis...play," SPIE Vol. 1667 Practical Holography VI, 32-43 (February 1992). 16. Marraud, A. and M. Bonnet . "Restitution of Stereoscopic Picture by Means

  12. Gargamelle optical tube

    CERN Multimedia

    1970-01-01

    Gargamelle was the name given to a big bubble chamber built at the Saclay Laboratory in France during the late 1960s. The experiment ran at CERN from 1970 - 1976 and in 1973 found the first experimental evidence of the particles responsible for transmitting the weak force. The weak force, one of the 4 fundamental interactions at work in the universe, has long been the subject of research at CERN. The force is responsible for radioactivity and is the reason why the sun shines. Gargamelle observed what is known as neutral currents, the process of a neutrino and electron transforming into a muon and a neutrino by exchanging an electrically neutral force carrier. The interaction was triggered by a beam of neutrinos and recorded by photographing the trail of bubbles left behind in the freon that filled the experiment's main chamber. Gargamelle has been conserved and is now displayed in the Microcosm garden.

  13. INFORMATION DISPLAY: CONSIDERATIONS FOR DESIGNING COMPUTER-BASED DISPLAY SYSTEMS.

    Energy Technology Data Exchange (ETDEWEB)

    O' HARA,J.M.; PIRUS,D.; BELTRATCCHI,L.

    2004-09-19

    This paper discussed the presentation of information in computer-based control rooms. Issues associated with the typical displays currently in use are discussed. It is concluded that these displays should be augmented with new displays designed to better meet the information needs of plant personnel and to minimize the need for interface management tasks (the activities personnel have to do to access and organize the information they need). Several approaches to information design are discussed, specifically addressing: (1) monitoring, detection, and situation assessment; (2) routine task performance; and (3) teamwork, crew coordination, collaborative work.

  14. Flat panel display - Impurity doping technology for flat panel displays

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Toshiharu [Advanced Technology Planning, Sumitomo Eaton Nova Corporation, SBS Tower 9F, 10-1, Yoga 4-chome, Setagaya-ku, 158-0097 Tokyo (Japan)]. E-mail: suzuki_tsh@senova.co.jp

    2005-08-01

    Features of the flat panel displays (FPDs) such as liquid crystal display (LCD) and organic light emitting diode (OLED) display, etc. using low temperature poly-Si (LTPS) thin film transistors (TFTs) are briefly reviewed comparing with other FPDs. The requirements for fabricating TFTs used for high performance FPDs and system on glass (SoG) are addressed. This paper focuses on the impurity doping technology, which is one of the key technologies together with crystallization by laser annealing, formation of high quality gate insulator and gate-insulator/poly-Si interface. The issues to be solved in impurity doping technology for state of the art and future TFTs are clarified.

  15. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... Grants and Funding Extramural Research Division of Extramural Science Programs Division of Extramural Activities Extramural Contacts NEI ... Amaurosis Low Vision Refractive Errors Retinopathy of Prematurity Science Spanish Videos Webinars NEI YouTube Videos: Amblyopia Embedded ...

  16. Epidemiology of neural tube defects

    National Research Council Canada - National Science Library

    Seidahmed, Mohammed Z; Abdelbasit, Omar B; Shaheed, Meeralebbae M; Alhussein, Khalid A; Miqdad, Abeer M; Khalil, Mohamed I; Al-Enazy, Naif M; Salih, Mustafa A

    2014-01-01

    To find the prevalence of neural tube defects (NTDs), and compare the findings with local and international data, and highlight the important role of folic acid supplementation and flour fortification with folic acid in preventing NTDs...

  17. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... Intern Program Diversity In Vision Research & Ophthalmology (DIVRO) Student Training Programs To search for current job openings visit HHS USAJobs Home > NEI YouTube Videos > ...

  18. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... questions Clinical Studies Publications Catalog Photos and Images Spanish Language Information Grants and Funding Extramural Research Division ... Low Vision Refractive Errors Retinopathy of Prematurity Science Spanish Videos Webinars NEI YouTube Videos: Amblyopia Embedded video ...

  19. NEI You Tube Videos: Amblyopia

    Medline Plus

    Full Text Available ... and Aging Program African American Program Training and Jobs Fellowships NEI Summer Intern Program Diversity In Vision ... DIVRO) Student Training Programs To search for current job openings visit HHS USAJobs Home > NEI YouTube Videos > ...

  20. Examination of gavage tube placement in children.

    Science.gov (United States)

    Ellett, M L; Beckstrand, J

    1999-01-01

    A primary issue in ensuring safe and effective enteral feeding by tube is achieving and maintaining correct tube position. This study was conducted to determine the prevalence of tube placement errors, risk factors associated with these errors, and accuracy of commonly used bedside placement-screening methods. In this descriptive study, 39 hospitalized children having one or more types of enteral tubes were studied prospectively. Tube placement was assessed across time, using three common placement-screening methods compared to radiographs. Tube placement error occurred in 43.5% of tubes at least once during the observation period. Children who were comatose or semicomatose, were inactive, had swallowing problems, or had Argyle tubes were more likely to have tube placement errors. Findings suggest that radiographs to document tube placement may be needed, at least on initial enteral tube insertion.

  1. Tone compatibility between HDR displays

    Science.gov (United States)

    Bist, Cambodge; Cozot, Rémi; Madec, Gérard; Ducloux, Xavier

    2016-09-01

    High Dynamic Range (HDR) is the latest trend in television technology and we expect an in ux of HDR capable consumer TVs in the market. Initial HDR consumer displays will operate on a peak brightness of about 500-1000 nits while in the coming years display peak brightness is expected to go beyond 1000 nits. However, professionally graded HDR content can range from 1000 to 4000 nits. As with Standard Dynamic Range (SDR) content, we can expect HDR content to be available in variety of lighting styles such as low key, medium key and high key video. This raises concerns over tone-compatibility between HDR displays especially when adapting to various lighting styles. It is expected that dynamic range adaptation between HDR displays uses similar techniques as found with tone mapping and tone expansion operators. In this paper, we survey simple tone mapping methods of 4000 nits color-graded HDR content for 1000 nits HDR displays. We also investigate tone expansion strategies when HDR content graded in 1000 nits is displayed on 4000 nits HDR monitors. We conclude that the best tone reproduction technique between HDR displays strongly depends on the lighting style of the content.

  2. Dermatology on YouTube.

    Science.gov (United States)

    Boyers, Lindsay N; Quest, Tyler; Karimkhani, Chante; Connett, Jessica; Dellavalle, Robert P

    2014-06-15

    YouTube, reaches upwards of six billion users on a monthly basis and is a unique source of information distribution and communication. Although the influence of YouTube on personal health decision-making is well established, this study assessed the type of content and viewership on a broad scope of dermatology related content on YouTube. Select terms (i.e. dermatology, sun protection, skin cancer, skin cancer awareness, and skin conditions) were searched on YouTube. Overall, the results included 100 videos with over 47 million viewers. Advocacy was the most prevalent content type at 24% of the total search results. These 100 videos were "shared" a total of 101,173 times and have driven 6,325 subscriptions to distinct YouTube user pages. Of the total videos, 35% were uploaded by or featured an MD/DO/PhD in dermatology or other specialty/field, 2% FNP/PA, 1% RN, and 62% other. As one of the most trafficked global sites on the Internet, YouTube is a valuable resource for dermatologists, physicians in other specialties, and the general public to share their dermatology-related content and gain subscribers. However, challenges of accessing and determining evidence-based data remain an issue.

  3. Texture-Based Correspondence Display

    Science.gov (United States)

    Gerald-Yamasaki, Michael

    2004-01-01

    Texture-based correspondence display is a methodology to display corresponding data elements in visual representations of complex multidimensional, multivariate data. Texture is utilized as a persistent medium to contain a visual representation model and as a means to create multiple renditions of data where color is used to identify correspondence. Corresponding data elements are displayed over a variety of visual metaphors in a normal rendering process without adding extraneous linking metadata creation and maintenance. The effectiveness of visual representation for understanding data is extended to the expression of the visual representation model in texture.

  4. Circular displays: control/display arrangements and stereotype strength with eight different display locations.

    Science.gov (United States)

    Chan, Alan H S; Hoffmann, Errol R

    2015-01-01

    Two experiments are reported that were designed to investigate control/display arrangements having high stereotype strengths when using circular displays. Eight display locations relative to the operator and control were tested with rotational and translational controls situated on different planes according to the Frame of Reference Transformation Tool (FORT) model of Wickens et al. (2010). (Left. No, Right! Development of the Frame of Reference Transformation Tool (FORT), Proceedings of the Human Factors and Ergonomics Society 54th Annual Meeting, 54: 1022-1026). In many cases, there was little effect of display locations, indicating the importance of the Worringham and Beringer (1998. Directional stimulus-response compatibility: a test of three alternative principles. Ergonomics, 41(6), 864-880) Visual Field principle and an extension of this principle for rotary controls (Hoffmann and Chan (2013). The Worringham and Beringer 'visual field' principle for rotary controls. Ergonomics, 56(10), 1620-1624). The initial indicator position (12, 3, 6 and 9 o'clock) had a major effect on control/display stereotype strength for many of the six controls tested. Best display/control arrangements are listed for each of the different control types (rotational and translational) and for the planes on which they are mounted. Data have application where a circular display is used due to limited display panel space and applies to space-craft, robotics operators, hospital equipment and home appliances. Practitioner Summary: Circular displays are often used when there is limited space available on a control panel. Display/control arrangements having high stereotype strength are listed for four initial indicator positions. These arrangements are best for design purposes.

  5. Ultraminiature, Micropower Multipurpose Display Project

    Data.gov (United States)

    National Aeronautics and Space Administration — High information content electronic displays remain the most difficult element of the human-machine interface to effectively miniaturize. Mobile applications need a...

  6. Color speckle in laser displays

    Science.gov (United States)

    Kuroda, Kazuo

    2015-07-01

    At the beginning of this century, lighting technology has been shifted from discharge lamps, fluorescent lamps and electric bulbs to solid-state lighting. Current solid-state lighting is based on the light emitting diodes (LED) technology, but the laser lighting technology is developing rapidly, such as, laser cinema projectors, laser TVs, laser head-up displays, laser head mounted displays, and laser headlamps for motor vehicles. One of the main issues of laser displays is the reduction of speckle noise1). For the monochromatic laser light, speckle is random interference pattern on the image plane (retina for human observer). For laser displays, RGB (red-green-blue) lasers form speckle patterns independently, which results in random distribution of chromaticity, called color speckle2).

  7. ATLAS muon drift tube production in Seattle

    CERN Document Server

    Zhao, T; Kuykendall, W; Davisson, R

    2004-01-01

    The drift tube production facility that we developed for producing precision drift tubes of the ATLAS forward muon system in our laboratory is described in this paper. The results of quality assurance for approximately 30,000 tube produced are given. Our experience shows that this production facility is very efficient and the quality of produced drift tubes is very high. (2 refs).

  8. 27 CFR 41.35 - Cigarette tubes.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Cigarette tubes. 41.35... OF THE TREASURY (CONTINUED) TOBACCO IMPORTATION OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Taxes Tax Rates § 41.35 Cigarette tubes. Cigarette tubes are taxed at the following rates...

  9. 21 CFR 872.6570 - Impression tube.

    Science.gov (United States)

    2010-04-01

    ... DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6570 Impression tube. (a) Identification. An impression tube is a device consisting of a hollow copper tube intended to take an impression of a single tooth... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Impression tube. 872.6570 Section 872.6570 Food...

  10. Physics of magnetic flux tubes

    CERN Document Server

    Ryutova, Margarita

    2015-01-01

    This book is the first account of the physics of magnetic flux tubes from their fundamental properties to collective phenomena in an ensembles of flux tubes. The physics of magnetic flux tubes is absolutely vital for understanding fundamental physical processes in the solar atmosphere shaped and governed by magnetic fields. High-resolution and high cadence observations from recent space and  ground-based instruments taken simultaneously at different heights and temperatures not only show the ubiquity of filamentary structure formation but also allow to study how various events are interconnected by system of magnetic flux tubes. The book covers both theory and observations. Theoretical models presented in analytical and phenomenological forms are tailored for practical applications. These are welded with state-of-the-art observations from early decisive ones to the most recent data that open a new phase-space for exploring the Sun and sun-like stars. Concept of magnetic flux tubes is central to various magn...

  11. Implementation of PIC Based LED Displays

    OpenAIRE

    Htet Htet Thit San; Chaw Myat Nwe; Hla Myo Tun

    2014-01-01

    This paper explains the project which is a special kind of LED Display Board for performing dance movement according to the rhythm of music. Nowadays, LED display boards are widely used in advertising and other applications. LED display boards can also be used indoors or outdoors. The objective of this system is to design a display panel by using several dozens of LED matrix display. The display pattern can desire to be changed easily and modified by the user. This LED display...

  12. Tubing and cable cutting tool

    Science.gov (United States)

    Mcsmith, D. D.; Richardson, J. I. (Inventor)

    1984-01-01

    A hand held hydraulic cutting tool was developed which is particularly useful in deactivating ejection seats in military aircraft rescue operations. The tool consists primarily of a hydraulic system composed of a fluid reservoir, a pumping piston, and an actuator piston. Mechanical cutting jaws are attached to the actuator piston rod. The hydraulic system is controlled by a pump handle. As the pump handle is operated the actuator piston rod is forced outward and thus the cutting jaws are forced together. The frame of the device is a flexible metal tubing which permits easy positioning of the tool cutting jaws in remote and normally inaccessible locations. Bifurcated cutting edges ensure removal of a section of the tubing or cable to thereby reduce the possibility of accidental reactivation of the tubing or cable being severed.

  13. On hydraulics of capillary tubes

    Directory of Open Access Journals (Sweden)

    N.G. Aloyan

    2016-03-01

    Full Text Available The article considers the laws of motion of water in the capillary tubes, taken as a model for flowing well, on the analogical net count device. For capillary tube the lower limit value of flow rate is empirically determined above which the total hydraulic resistance of the capillary is practically constant. The specificity of the phenomenon is that the regime of motion, by a Reynolds number, for a given flow rate still remains laminar. This circumstance can perplex the specialists, so the author invites them to the scientific debate on the subject of study. Obviously, to identify the resulting puzzle it is necessary to conduct a series of experiments using capillaries of different lengths and diameters and with different values of overpressure. The article states that in tubes with very small diameter the preliminary magnitude of capillary rise of water in the presence of flow plays no role and can be neglected.

  14. Drift tubes of Linac 2

    CERN Multimedia

    CERN PhotoLab

    1977-01-01

    With the advent of the 800 MeV PS Booster in 1972, the original injector of the PS, a 50 MeV Alvarez-type proton linac, had reached its limits, in terms of intensity and stability. In 1973 one therefore decided to build a new linac (Linac 2), also with a drift-tube Alvarez structure and an energy of 50 MeV. It had a new Cockcroft-Walton preinjector with 750 keV, instead of the previous one with 500 keV. Linac 2 was put into service in 1980. The old Linac 1 was then used for the study of, and later operation with, various types of ions. This picture shows Linac 2 drift-tubes, suspended on stems coming from the top, in contrast to Linac 1, where the drift-tubes stood on stems coming from the bottom.

  15. On-line data display

    Science.gov (United States)

    Lang, Sherman Y. T.; Brooks, Martin; Gauthier, Marc; Wein, Marceli

    1993-05-01

    A data display system for embedded realtime systems has been developed for use as an operator's user interface and debugging tool. The motivation for development of the On-Line Data Display (ODD) have come from several sources. In particular the design reflects the needs of researchers developing an experimental mobile robot within our laboratory. A proliferation of specialized user interfaces revealed a need for a flexible communications and graphical data display system. At the same time the system had to be readily extensible for arbitrary graphical display formats which would be required for data visualization needs of the researchers. The system defines a communication protocol transmitting 'datagrams' between tasks executing on the realtime system and virtual devices displaying the data in a meaningful way on a graphical workstation. The communication protocol multiplexes logical channels on a single data stream. The current implementation consists of a server for the Harmony realtime operating system and an application written for the Macintosh computer. Flexibility requirements resulted in a highly modular server design, and a layered modular object- oriented design for the Macintosh part of the system. Users assign data types to specific channels at run time. Then devices are instantiated by the user and connected to channels to receive datagrams. The current suite of device types do not provide enough functionality for most users' specialized needs. Instead the system design allows the creation of new device types with modest programming effort. The protocol, design and use of the system are discussed.

  16. Three-dimensional display technologies

    Science.gov (United States)

    Geng, Jason

    2014-01-01

    The physical world around us is three-dimensional (3D), yet traditional display devices can show only two-dimensional (2D) flat images that lack depth (i.e., the third dimension) information. This fundamental restriction greatly limits our ability to perceive and to understand the complexity of real-world objects. Nearly 50% of the capability of the human brain is devoted to processing visual information [Human Anatomy & Physiology (Pearson, 2012)]. Flat images and 2D displays do not harness the brain’s power effectively. With rapid advances in the electronics, optics, laser, and photonics fields, true 3D display technologies are making their way into the marketplace. 3D movies, 3D TV, 3D mobile devices, and 3D games have increasingly demanded true 3D display with no eyeglasses (autostereoscopic). Therefore, it would be very beneficial to readers of this journal to have a systematic review of state-of-the-art 3D display technologies. PMID:25530827

  17. Fabrication and properties of gallium phosphide variable colour displays

    Science.gov (United States)

    Effer, D.; Macdonald, R. A.; Macgregor, G. M.; Webb, W. A.; Kennedy, D. I.

    1973-01-01

    The unique properties of single-junction gallium phosphide devices incorporating both red and green radiative recombination centers were investigated in application to the fabrication of monolithic 5 x 7 displays capable of displaying symbolic and alphanumeric information in a multicolor format. A number of potentially suitable material preparation techniques were evaluated in terms of both material properties and device performance. Optimum results were obtained for double liquid-phase-epitaxial process in which an open-tube dipping technique was used for n-layer growth and a sealed tipping procedure for subsequent p-layer growth. It was demonstrated that to prepare devices exhibiting a satisfactory range of dominant wavelengths which can be perceived as distinct emission colors extending from the red through green region of the visible spectrum involves a compromise between the material properties necessary for efficient red emission and those considered optimum for efficient green emission.

  18. The pollen tube paradigm revisited.

    Science.gov (United States)

    Kroeger, Jens; Geitmann, Anja

    2012-12-01

    The polar growth process characterizing pollen tube elongation has attracted numerous modeling attempts over the past years. While initial models focused on recreating the correct cellular geometry, recent models are increasingly based on experimentally assessed cellular parameters such as the dynamics of signaling processes and the mechanical properties of the cell wall. Recent modeling attempts have therefore substantially gained in biological relevance and predictive power. Different modeling methods are explained and the power and limitations of individual models are compared. Focus is on several recent models that use closed feedback loops in order to generate limit cycles representing the oscillatory behavior observed in growing tubes. Copyright © 2012 Elsevier Ltd. All rights reserved.

  19. YouTube and Facebook

    DEFF Research Database (Denmark)

    Robertson, Scott P.; Vatrapu, Ravi; Medina, Richard

    This paper examines the links to YouTube from the Facebook “walls” of Barack Obama, Hillary Clinton, and John McCain over two years prior to the 2008 U.S. Presidential election. User-generated linkage patterns show how participants in these politically-related social networking dialogues used...... online video to make their points. We show a strong integration of the Web 2.0 and new media technologies of social networking and online video. We argue that political discussion in social networking environments can no longer be viewed as primarily textual, and that neither Facebook nor YouTube can...

  20. Working session 3: Tubing integrity

    Energy Technology Data Exchange (ETDEWEB)

    Cueto-Felgueroso, C. [Tecnatom, S.A., San Sebastian de los Reyes, Madrid (Spain); Strosnider, J. [NRC, Washington, DC (United States)

    1997-02-01

    Twenty-three individuals representing nine countries (Belgium, Canada, the Czech Republic, France, Japan, the Slovak Republic, Spain, the UK, and the US) participated in the session on tube integrity. These individuals represented utilities, vendors, consultants and regulatory authorities. The major subjects discussed by the group included overall objectives of managing steam generator tube degradation, necessary elements of a steam generator degradation management program, the concept of degradation specific management, structural integrity evaluations, leakage evaluations, and specific degradation mechanisms. The group`s discussions on these subjects, including conclusions and recommendations, are summarized in this article.

  1. Orifice plates and venturi tubes

    CERN Document Server

    Reader-Harris, Michael

    2015-01-01

    This book gives the background to differential-pressure flow measurement and goes through the requirements explaining the reason for them. For those who want to use an orifice plate or a Venturi tube the standard ISO 5167 and its associated Technical Reports give the instructions required.  However, they rarely tell the users why they should follow certain instructions.  This book helps users of the ISO standards for orifice plates and Venturi tubes to understand the reasons why the standards are as they are, to apply them effectively, and to understand the consequences of deviations from the standards.

  2. Biocompatibility of Different Nerve Tubes

    Directory of Open Access Journals (Sweden)

    Hisham Fansa

    2009-09-01

    Full Text Available Bridging nerve gaps with suitable grafts is a major clinical problem. The autologous nerve graft is considered to be the gold standard, providing the best functional results; however, donor site morbidity is still a major disadvantage. Various attempts have been made to overcome the problems of autologous nerve grafts with artificial nerve tubes, which are “ready-to-use” in almost every situation. A wide range of materials have been used in animal models but only few have been applied to date clinically, where biocompatibility is an inevitable prerequisite. This review gives an idea about artificial nerve tubes with special focus on their biocompatibility in animals and humans.

  3. To 'display' or not to 'display'- that is the peptide

    CSIR Research Space (South Africa)

    Crampton, Michael C

    2008-11-01

    Full Text Available Microbial cell surface display is the anchoring of a heterologous protein or peptide (passenger) to the outside of the cell wall as a fusion to a cell surface associated protein (carrier). This technology has been used extensively for both...

  4. 'No power' (green) electrowetting display

    Science.gov (United States)

    Jentsch, Michael; Rawert, Juergen; Jerosch, Dieter; Blankenbach, Karlheinz

    2011-05-01

    Electrowetting displays were first reported in 1981, several approaches were examined. However, ADT's "Droplet- Driven-Displays" technology is the only bistable one which makes them very attractive for energy-saving systems. That means that the power supply can completely shut off after changing the content and it will keep its information for years. More features that make the ADT approach very unique are paper like white appearance (even in the powerless OFFstate) and the capability for backlighting (most of the other e-paper technologies like electrophoretics can not be backlighted). Further achievements are a white state reflectance of about 70% resulting in sunlight readability and a pixel size in the range from 0.3mm to 10mm. Summarizing, ADT's electrowetting technology is highly suitable for lowest power (means eco-friendly or "green") displays.

  5. Pump element for a tube pump

    DEFF Research Database (Denmark)

    2011-01-01

    The invention relates to a tube pump comprising a tube and a pump element inserted in the tube, where the pump element comprises a rod element and a first and a second non-return valve member positioned a distance apart on the rod element. The valve members are oriented in the same direction...... portion acts to alternately close and open the valve members thereby generating a fluid flow through the tube. The invention further relates to a pump element comprising at least two non-return valve members connected by a rod element, and for insertion in an at least partly flexible tube in such tube...... pump as mentioned above, thereby acting to generate a fluid flow through the tube upon repeated deformation of the tube between the two valve members. The pump element may comprise a connecting part for coupling to another tube and may comprise a sealing part establishing a fluid tight connection...

  6. Drag and drop display & builder

    Energy Technology Data Exchange (ETDEWEB)

    Bolshakov, Timofei B.; Petrov, Andrey D.; /Fermilab

    2007-12-01

    The Drag and Drop (DnD) Display & Builder is a component-oriented system that allows users to create visual representations of data received from data acquisition systems. It is an upgrade of a Synoptic Display mechanism used at Fermilab since 2002. Components can be graphically arranged and logically interconnected in the web-startable Project Builder. Projects can be either lightweight AJAX- and SVG-based web pages, or they can be started as Java applications. The new version was initiated as a response to discussions between the LHC Controls Group and Fermilab.

  7. NIST display colorimeter calibration facility

    Science.gov (United States)

    Brown, Steven W.; Ohno, Yoshihiro

    2003-07-01

    A facility has been developed at the National Institute of Standards and Technology (NIST) to provide calibration services for color-measuring instruments to address the need for improving and certifying the measurement uncertainties of this type of instrument. While NIST has active programs in photometry, flat panel display metrology, and color and appearance measurements, these are the first services offered by NIST tailored to color-measuring instruments for displays. An overview of the facility, the calibration approach, and associated uncertainties are presented. Details of a new tunable colorimetric source and the development of new transfer standard instruments are discussed.

  8. 40 CFR 91.1007 - Display exemption.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Display exemption. 91.1007 Section 91....1007 Display exemption. An uncertified marine SI engine is a display engine when it is to be used solely for display purposes, will only be operated incident and necessary to the display purpose, and...

  9. 40 CFR 89.907 - Display exemption.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Display exemption. 89.907 Section 89....907 Display exemption. Where an uncertified nonroad engine is a display engine to be used solely for display purposes, will only be operated incident and necessary to the display purpose, and will not be...

  10. Thermal inhomogeneities in vortex tubes

    Science.gov (United States)

    Lemesh, N. I.; Senchuk, L. A.

    An experimental study of the effect of the temperature of the inlet gas on the temperature difference between the hot and cold streams discharged from a Ranque-Hilsch vortex tube is described. The experimental results are presented in graphical form. It is that the temperature difference increases with the temperature of the entering gas.

  11. Working session 1: Tubing degradation

    Energy Technology Data Exchange (ETDEWEB)

    Kharshafdjian, G. [Atomic Energy of Canada, Mississauga, Ontario (Canada); Turluer, G. [IPSN, Fontenay-aux-Roses (France)

    1997-02-01

    A general introductory overview of the purpose of the group and the general subject area of SG tubing degradation was given by the facilitator. The purpose of the session was described as to {open_quotes}develop conclusions and proposals on regulatory and technical needs required to deal with the issues of SG tubing degradation.{close_quotes} Types, locations and characteristics of tubing degradation in steam generators were briefly reviewed. The well-known synergistic effects of materials, environment, and stress and strain/strain rate, subsequently referred to by the acronym {open_quotes}MESS{close_quotes} by some of the group members, were noted. The element of time (i.e., evolution of these variables with time) was emphasized. It was also suggested that the group might want to consider the related topics of inspection capabilities, operational variables, degradation remedies, and validity of test data, and some background information in these areas was provided. The presentation given by Peter Millet during the Plenary Session was reviewed; Specifically, the chemical aspects and the degradation from the secondary side of the steam generator were noted. The main issues discussed during the October 1995 EPRI meeting on secondary side corrosion were reported, and a listing of the potential SG tube degradations was provided and discussed.

  12. Kundt's Tube Experiment Using Smartphones

    Science.gov (United States)

    Parolin, Sara Orsola; Pezzi, Giovanni

    2015-01-01

    This article deals with a modern version of Kundt's tube experiment. Using economic instruments and a couple of smartphones, it is possible to "see" nodes and antinodes of standing acoustic waves in a column of vibrating air and to measure the speed of sound.

  13. Vitamins and neural tube defects

    OpenAIRE

    Harris, Rodney

    1988-01-01

    The use of vitamin supplements by women around the time of conception was examined and compared in those having babies with neural tube defects, those with still births or some other type of malformation, and in women who had normal babies.

  14. OurTube / David Talbot

    Index Scriptorium Estoniae

    Talbot, David

    2009-01-01

    USA California Ülikooli töötajate Abram Stern'i ja Michael Dale'i poolt 2005. a. algatatud USA kongressis peetud kõnede videoremiksidest ja nende poolt loodud veebisaidist Metavid.org. Ka YouTube keskkonnast ja wikipedia katsetustest muuta oma keskkond multimeedialisemaks

  15. Fin-tube solar collectors

    Science.gov (United States)

    1980-01-01

    Report presents test procedures and results of thermal-performance evaluation of seven commercial fin tube (liquid) solar collector-absorber plates. Tests were conducted indoors at Marshall Space Flight Center Solar simulator. Results are graphically shown along with supporting test data and summary, indicating efficiency as function of collector inlet temperature.

  16. Tube Suction Test for Evaluating

    Science.gov (United States)

    2012-06-01

    In a comprehensive laboratory study, different tests namely, unconfined compressive strength (UCS) at the end of freeze-thaw/wet-dry (F-T/W-D) cycles, resilient modulus (Mr) at the end of F-T/W-D cycles, vacuum saturation, tube suction, and moisture ...

  17. Building your own shock tube

    NARCIS (Netherlands)

    J. Naber (Jorick)

    2005-01-01

    textabstractThis report treats the development of a shock tube solver for the simulation of flows described by the one-dimensional Euler equations. A well-known one-dimensional flow problem is the initial Riemann problem, which treats the development of a flow due to two initially separated

  18. Welding the CNGS decay tube

    CERN Multimedia

    Maximilien Brice

    2004-01-01

    3.6 km of welds were required for the 1 km long CERN Neutrinos to Gran Sasso (CNGS) decay tube, in which particles produced in the collision with a proton and a graphite target will decay into muons and muon neutrinos. Four highly skilled welders performed this delicate task.

  19. Application of EAP materials toward a refreshable Braille display

    Science.gov (United States)

    Di Spigna, N.; Chakraborti, P.; Yang, P.; Ghosh, T.; Franzon, P.

    2009-03-01

    The development of a multiline, refreshable Braille display will assist with the full inclusion and integration of blind people into society. The use of both polyvinylidene fluoride (PVDF) film planar bending mode actuators and silicone dielectric elastomer cylindrical tube actuators have been investigated for their potential use in a Braille cell. A liftoff process that allows for aggressive scaling of miniature bimorph actuators has been developed using standard semiconductor lithography techniques. The PVDF bimorphs have been demonstrated to provide enough displacement to raise a Braille dot using biases less than 1000V and operating at 10Hz. In addition, silicone tube actuators have also been demonstrated to achieve the necessary displacement, though requiring higher voltages. The choice of electrodes and prestrain conditions aimed at maximizing axial strain in tube actuators are discussed. Characterization techniques measuring actuation displacement and blocking forces appropriate for standard Braille cell specifications are presented. Finally, the integration of these materials into novel cell designs and the fabrication of a prototype Braille cell are discussed.

  20. Display Apple M7649Zm

    CERN Multimedia

    2001-01-01

    It was Designed for the Power Mac G4. This Apple studio display gives you edge-to-edge distortion-free images. With more than 16.7 million colors and 1,280 x 1,024 dpi resolution, you view brilliant and bright images on this Apple 17-inch monitor.

  1. Real Time Sonic Boom Display

    Science.gov (United States)

    Haering, Ed

    2014-01-01

    This presentation will provide general information about sonic boom mitigation technology to the public in order to supply information to potential partners and licensees. The technology is a combination of flight data, atmospheric data and terrain information implemented into a control room real time display for flight planning. This research is currently being performed and as such, any results and conclusions are ongoing.

  2. Solar active region display system

    Science.gov (United States)

    Golightly, M.; Raben, V.; Weyland, M.

    2003-04-01

    The Solar Active Region Display System (SARDS) is a client-server application that automatically collects a wide range of solar data and displays it in a format easy for users to assimilate and interpret. Users can rapidly identify active regions of interest or concern from color-coded indicators that visually summarize each region's size, magnetic configuration, recent growth history, and recent flare and CME production. The active region information can be overlaid onto solar maps, multiple solar images, and solar difference images in orthographic, Mercator or cylindrical equidistant projections. Near real-time graphs display the GOES soft and hard x-ray flux, flare events, and daily F10.7 value as a function of time; color-coded indicators show current trends in soft x-ray flux, flare temperature, daily F10.7 flux, and x-ray flare occurrence. Through a separate window up to 4 real-time or static graphs can simultaneously display values of KP, AP, daily F10.7 flux, GOES soft and hard x-ray flux, GOES >10 and >100 MeV proton flux, and Thule neutron monitor count rate. Climatologic displays use color-valued cells to show F10.7 and AP values as a function of Carrington/Bartel's rotation sequences - this format allows users to detect recurrent patterns in solar and geomagnetic activity as well as variations in activity levels over multiple solar cycles. Users can customize many of the display and graph features; all displays can be printed or copied to the system's clipboard for "pasting" into other applications. The system obtains and stores space weather data and images from sources such as the NOAA Space Environment Center, NOAA National Geophysical Data Center, the joint ESA/NASA SOHO spacecraft, and the Kitt Peak National Solar Observatory, and can be extended to include other data series and image sources. Data and images retrieved from the system's database are converted to XML and transported from a central server using HTTP and SOAP protocols, allowing

  3. Perceptual limitations of peripherally displayed colors on CRTs

    Science.gov (United States)

    Ancman, Eileen G.

    1991-03-01

    Cathode ray tubes are currently used in aircraft cockpits to relay important color coded information necessary for mission completion and pilot survival. Color CRT's presently used are as large as 6 x 6 inch, but are projected to increase in size until the all glass cockpit is achieved. As the display gets larger, peripheral vision may be relied upon even more heavily. Peripheral vision is also important in present situations involving more than one CRT display used in a row, and especially when the pilot is in a head-up mode. The research in this report dealt with a subject's ability to recognize in their peripheral vision the three primary colors, blue, green, and red, on a cathode ray tube (CRT) with all three guns adjusted to achieve equal luminance. Data for various subject psychological states (normal, stressed, and relaxed) was collected. Percent error (e.g., how many times red was perceived as green or blue) was recorded for each state and color. A second performance measure, visual field dimension (e.g., degrees off of fovea where the color of the circle was correctly perceived) along the x-axis, was also collected for each color and psychological state.

  4. JTEC panel on display technologies in Japan

    Science.gov (United States)

    Tannas, Lawrence E., Jr.; Glenn, William E.; Credelle, Thomas; Doane, J. William; Firester, Arthur H.; Thompson, Malcolm

    1992-01-01

    This report is one in a series of reports that describes research and development efforts in Japan in the area of display technologies. The following are included in this report: flat panel displays (technical findings, liquid crystal display development and production, large flat panel displays (FPD's), electroluminescent displays and plasma panels, infrastructure in Japan's FPD industry, market and projected sales, and new a-Si active matrix liquid crystal display (AMLCD) factory); materials for flat panel displays (liquid crystal materials, and light-emissive display materials); manufacturing and infrastructure of active matrix liquid crystal displays (manufacturing logistics and equipment); passive matrix liquid crystal displays (LCD basics, twisted nematics LCD's, supertwisted nematic LCD's, ferroelectric LCD's, and a comparison of passive matrix LCD technology); active matrix technology (basic active matrix technology, investment environment, amorphous silicon, polysilicon, and commercial products and prototypes); and projection displays (comparison of Japanese and U.S. display research, and technical evaluation of work).

  5. Schizophrenia on YouTube.

    Science.gov (United States)

    Nour, Matthew M; Nour, Murraih H; Tsatalou, Olga-Maria; Barrera, Alvaro

    2017-01-01

    YouTube ( www.youtube.com ) is the most popular video-sharing Web site on the Internet and is used by medical students as a source of information regarding mental health conditions, including schizophrenia. The accuracy and educational utility of schizophrenia presentations on YouTube are unknown. The purpose of this study was to analyze the accuracy of depictions of psychosis in the context of a diagnosis of schizophrenia (referred to in this article as "acute schizophrenia") on YouTube and to assess the utility of these videos as educational tools for teaching medical students to recognize the clinical features of acute schizophrenia. YouTube was searched for videos purporting to show acute schizophrenia. Eligible videos were independently rated by two consultant psychiatrists on two separate occasions 22 days apart for diagnostic accuracy, psychopathology, and educational utility. Videos (N=4,200) were assessed against predefined inclusion and exclusion criteria. The majority were not eligible for further analysis, mostly because they did not claim to show a patient with schizophrenia (74%) or contained duplicated content (11%). Of 35 videos that met the eligibility and adequacy criteria, only 12 accurately depicted acute schizophrenia. Accurate videos were characterized by persecutory delusions (83%), inappropriate affect (75%), and negative symptoms (83%). Despite the fact that 83% of accurate videos were deemed to have good educational utility compared with 15% of inaccurate videos, accurate and inaccurate videos had similar view counts (290,048 versus 186,124). Schizophrenia presentations on YouTube offer a distorted picture of the condition.

  6. Display Sharing: An Alternative Paradigm

    Science.gov (United States)

    Brown, Michael A.

    2010-01-01

    The current Johnson Space Center (JSC) Mission Control Center (MCC) Video Transport System (VTS) provides flight controllers and management the ability to meld raw video from various sources with telemetry to improve situational awareness. However, maintaining a separate infrastructure for video delivery and integration of video content with data adds significant complexity and cost to the system. When considering alternative architectures for a VTS, the current system's ability to share specific computer displays in their entirety to other locations, such as large projector systems, flight control rooms, and back supporting rooms throughout the facilities and centers must be incorporated into any new architecture. Internet Protocol (IP)-based systems also support video delivery and integration. IP-based systems generally have an advantage in terms of cost and maintainability. Although IP-based systems are versatile, the task of sharing a computer display from one workstation to another can be time consuming for an end-user and inconvenient to administer at a system level. The objective of this paper is to present a prototype display sharing enterprise solution. Display sharing is a system which delivers image sharing across the LAN while simultaneously managing bandwidth, supporting encryption, enabling recovery and resynchronization following a loss of signal, and, minimizing latency. Additional critical elements will include image scaling support, multi -sharing, ease of initial integration and configuration, integration with desktop window managers, collaboration tools, host and recipient controls. This goal of this paper is to summarize the various elements of an IP-based display sharing system that can be used in today's control center environment.

  7. A case of a 'lost' nasogastric tube.

    Science.gov (United States)

    Sankar, V; Shakeel, M; Keh, S; Ah-See, K W

    2012-12-01

    To present the case of a 'lost' nasogastric tube and to highlight the importance of imaging and/or chest X-ray after nasogastric tube insertion, especially in unreliable patients. A 50-year-old man, undergoing radiotherapy treatment for squamous cell carcinoma of the tongue base, was admitted for pain control and nasogastric tube feeding. This patient required multiple nasogastric tubes over a two-week period. The patient repeatedly denied pulling the nasogastric tube out and we were unable to establish the exact mode of nasogastric tube removal. On one such occasion another tube was inserted and a check X-ray showed two feeding tubes; the latest one was lying in the left main bronchus and the old nasogastric tube was observed in the oesophagus, with its upper end jutting above the hypopharynx. It was apparent that the patient had somehow cut the tube and swallowed it. This case not only illustrates the importance of flexible nasendoscopy and/or chest X-ray for checking the position of the nasogastric tube, but also highlights that some patients are not tolerant of nasogastric tubes. The use of nasogastric tubes should be avoided in these patients to prevent any self-inflicted injury.

  8. Small bore ceramic laser tube inspection light table

    Science.gov (United States)

    Updike, Earl O.

    1990-01-01

    Apparatus for inspecting small bore ceramic laser tubes, which includes a support base with one or more support rollers. A fluorescent light tube is inserted within the laser tube and the laser tube is supported by the support rollers so that a gap is maintained between the laser tube and the fluorescent tube to enable rotation of the laser tube. In operation, the ceramic tube is illuminated from the inside by the fluorescent tube to facilitate visual inspection. Centering the tube around the axial light of the fluorescent tube provides information about straightness and wall thickness of the laser tube itself.

  9. The accessory fallopian tube: A rare anomaly

    Directory of Open Access Journals (Sweden)

    Kusum R Gandhi

    2012-01-01

    Full Text Available This paper presents a rare anatomical variation in the form of accessory fallopian tube on right side. The duplication of fallopian tube was observed in a 34-year-old female during routine undergraduate dissection in our department. Fallopian tube is the part of uterus that carries the ovum from the ovary to the uterus. Accessory fallopian tube is the congenital anomaly attached to the ampullary part of main tube. This accessory tube is common site of pyosalpinx, hydrosalpinx, cystic swelling and torsion. The ovum released by the ovary may also be captured by the blind accessory tube leading to infertility or ectopic pregnancy. Hence, all patients of infertility or pelvic inflammatory disease should be screened to rule out the presence of accessory fallopian tube and if encountered should be removed.

  10. Childhood re-edits: challenging norms and forming lay professional competence on YouTube

    Directory of Open Access Journals (Sweden)

    Konstantin Economou

    2015-12-01

    Full Text Available This article presents the initial findings of research into how YouTube culture can become an arena for young YouTube videographers to remodel mainstream, sub-cultural, and media content (YouTube clips, music, film content, and viral memes. We juxtapose analyses from both media and child studies to look at the ways in which preferred images and notions of the “good” and idyllic childhood are re-edited into a possible critique of the prescribed Swedish childhood. Also, we look at ways in which these media-literate actors use YouTube to display their skills in both media editing and social media “savvy.” We discuss how “lay” professional competence in digital culture can be inherent in a friction between popular (children's culture and social media production, where simultaneous prowess in both is important for how a mediatised social and cultural critique can emerge.

  11. Models for Automated Tube Performance Calculations

    Energy Technology Data Exchange (ETDEWEB)

    C. Brunkhorst

    2002-12-12

    High power radio-frequency systems, as typically used in fusion research devices, utilize vacuum tubes. Evaluation of vacuum tube performance involves data taken from tube operating curves. The acquisition of data from such graphical sources is a tedious process. A simple modeling method is presented that will provide values of tube currents for a given set of element voltages. These models may be used as subroutines in iterative solutions of amplifier operating conditions for a specific loading impedance.

  12. Transparent stereoscopic display and application

    Science.gov (United States)

    Ranieri, Nicola; Seifert, Hagen; Gross, Markus

    2014-03-01

    Augmented reality has become important to our society as it can enrich the actual world with virtual information. Transparent screens offer one possibility to overlay rendered scenes with the environment, acting both as display and window. In this work, we review existing transparent back-projection screens for the use with active and passive stereo. Advantages and limitations are described and, based on these insights, a passive stereoscopic system using an anisotropic back-projection foil is proposed. To increase realism, we adapt rendered content to the viewer's position using a Kinect tracking system, which adds motion parallax to the binocular cues. A technique well known in control engineering is used to decrease latency and increase frequency of the tracker. Our transparent stereoscopic display prototype provides immersive viewing experience and is suitable for many augmented reality applications.

  13. Game engines and immersive displays

    Science.gov (United States)

    Chang, Benjamin; Destefano, Marc

    2014-02-01

    While virtual reality and digital games share many core technologies, the programming environments, toolkits, and workflows for developing games and VR environments are often distinct. VR toolkits designed for applications in visualization and simulation often have a different feature set or design philosophy than game engines, while popular game engines often lack support for VR hardware. Extending a game engine to support systems such as the CAVE gives developers a unified development environment and the ability to easily port projects, but involves challenges beyond just adding stereo 3D visuals. In this paper we outline the issues involved in adapting a game engine for use with an immersive display system including stereoscopy, tracking, and clustering, and present example implementation details using Unity3D. We discuss application development and workflow approaches including camera management, rendering synchronization, GUI design, and issues specific to Unity3D, and present examples of projects created for a multi-wall, clustered, stereoscopic display.

  14. Human Vocabulary Use as Display

    Directory of Open Access Journals (Sweden)

    Jeremy Rosenberg

    2008-07-01

    Full Text Available The average human vocabulary consists of approximately 20,000 word families, yet only 6000-7000 word families are required to understand most communication. One possible explanation for this level of redundancy is that vocabulary size is selected as a fitness indicator and is used for display. Human vocabulary size correlates highly with measurable intelligence and when choosing potential mates individuals actively prefer other correlates of intelligence, such as education. Here we show that males used more low frequency words after an imaginary romantic encounter with a young female shown in a photograph relative to when they viewed photographs of older females. Females used fewer low frequency words when they imagined a romantic encounter with a young male shown in a photograph relative to when they viewed photographs of older males. These differences in male and female vocabulary displays may be related to sex differences in investment costs in offspring.

  15. Insta-Head: An Instant Headgear Tube

    Directory of Open Access Journals (Sweden)

    Rajesh B Kuril

    2011-01-01

    Full Text Available Specialized headgear tubes are required for fabrication of appliances, such as activator-headgear and twin-block with headgear. The common problems with these tubes are that they need to be purchased beforehand and they are expensive. The present article describes the chairside fabrication of a simple, inexpensive headgear tube (insta-head without the need of any specialized armamentarium.

  16. A Novel Mediastinal Drainage Tube for Mediastinitis

    Directory of Open Access Journals (Sweden)

    Jun Ho Yhang

    2015-10-01

    Full Text Available Mediastinitis is a life-threatening disease, and effective drainage is needed to treat mediastinitis with abscess formation. We recommend an alternative drainage method using chest tube binding with a Silastic Penrose drainage tube. The use of a Silastic Penrose drainage tube may help to manage mediastinitis with abscess formation. This method facilitates effective draining and prevents tissue adhesion.

  17. Studies of Degraded Smelt Spout Opening Tubes

    Energy Technology Data Exchange (ETDEWEB)

    Keiser, James R [ORNL; Kish, Joseph R. [Paprican; Willoughby, Adam W [ORNL; Longmire, Hu Foster [ORNL; Singbeil, Douglas [Paprican

    2007-01-01

    Co-extruded type 304L stainless steel/SA210 carbon steel tubes have been used on the floors and lower walls of many black liquor recovery boilers to address the wall thinning problem that had been an issue for boiler owners and operators. Use of these tubes greatly reduced the corrosion issue, but corrosion was still sometimes observed and cracking was discovered in some tubes, particularly those that are bent to form the openings for smelt spouts. Because cracks in the opening tubes were sometimes observed to extend a significant distance into the tube wall and because these cracks were found fairly frequently, tubes made from a number of alternate cladding materials were tried in place of the 304L clad opening tubes. This paper describes the results of examinations of spout opening tubes of the standard 304L/carbon steel and of several of the alternate materials that have been tried. In addition to the corrosion and cracking seen in the spout opening tubes, another issue associated with these tubes has been observed. Preferential corrosion of the cap welds is sometimes seen on butt welds attaching the spout opening tubes made with alternate cladding materials to the standard 304L/carbon steel co-extruded wall tubes. Some information on the observations of this corrosion is also included in this paper.

  18. Radioactive fallout and neural tube defects

    African Journals Online (AJOL)

    Nejat Akar

    2015-07-10

    Jul 10, 2015 ... Neural tube defects;. Anencephaly;. Spina bifida. Abstract Possible link between radioactivity and the occurrence of neural tube defects is a long lasting debate ... Neural tube defects, are one of the common congenital mal- formations ... ent cities of Turkey (˙Izmir/Aegean Region; Trabzon/Black Sea region ...

  19. Clinical Burden of Laparoscopic Feeding Jejunostomy Tubes.

    Science.gov (United States)

    Speer, Emily A; Chow, Simon C; Dunst, Christy M; Shada, Amber L; Halpin, Valerie; Reavis, Kevin M; Cassera, Maria; Swanström, Lee L

    2016-05-01

    Feeding jejunostomies (J tubes) provide enteral nutrition when oral and gastric routes are not options. Despite their prevalence, there is a paucity of literature regarding their efficacy and clinical burden. All laparoscopic J tubes placed over a 5-year period were retrospectively reviewed. Clinical burden was measured by number of clinical contact events (tube-related clinic visits, phone calls, ED visits) and morbidity (dislodgement, clogging, tube fracture, infection, other). Tube replacements were also recorded. One hundred fifty-one patients were included. Fifty-nine percent had associated malignancy, and 35 % were placed for nutritional prophylaxis. Mean time to J tube removal was 146 days. J tubes were expected to be temporary in >90 % but only 50 % had sufficient oral intake for removal. Tubes were removed prematurely due to patient intolerance in 8 %. Mortality was 0 %. Morbidity was 51 % and included clogging (12 %), tube fracture (16 %), dislodgement (25 %), infection (18 %) and "other" (leaking, erosion, etc.) in 17 %. The median number of adverse events per J tube was 2(0-8). Mean number of clinic phone calls was 2.5(0-22), ED visits 0.5(0-7), and clinic visits 1.4(0-13), with 82 % requiring more than one J tube-related clinic visit. Unplanned replacements occurred in 40 %. While necessary for some patients, J tubes are associated with high clinical burden.

  20. Roll-forming tubes to header plates

    Science.gov (United States)

    Kramer, K.

    1976-01-01

    Technique has been developed for attaching and sealing tubes to header plates using a unique roll-forming tool. Technique is useful for attaching small tubes which are difficult to roll into conventional grooves in header plate tube holes, and for attaching when welding, brazing, or soldering is not desirable.

  1. The Fuge Tube Diode Array Spectrophotometer

    Science.gov (United States)

    Arneson, B. T.; Long, S. R.; Stewart, K. K.; Lagowski, J. J.

    2008-01-01

    We present the details for adapting a diode array UV-vis spectrophotometer to incorporate the use of polypropylene microcentrifuge tubes--fuge tubes--as cuvettes. Optical data are presented validating that the polyethylene fuge tubes are equivalent to the standard square cross section polystyrene or glass cuvettes generally used in…

  2. Kundt's Tube: An Acoustic Gas Analyzer

    Science.gov (United States)

    Aristov, Natasha; Habekost, Gehsa; Habekost, Achim

    2011-01-01

    A Kundt tube is normally used to measure the speed of sound in gases. Therefore, from known speeds of sound, a Kundt tube can be used to identify gases and their fractions in mixtures. In these experiments, the speed of sound is determined by measuring the frequency of a standing sound wave at a fixed tube length, temperature, and pressure. This…

  3. Spring/dimple instrument tube restraint

    Science.gov (United States)

    DeMario, Edmund E.; Lawson, Charles N.

    1993-01-01

    A nuclear fuel assembly for a pressurized water nuclear reactor has a spring and dimple structure formed in a non-radioactive insert tube placed in the top of a sensor receiving instrumentation tube thimble disposed in the fuel assembly and attached at a top nozzle, a bottom nozzle, and intermediate grids. The instrumentation tube thimble is open at the top, where the sensor or its connection extends through the cooling water for coupling to a sensor signal processor. The spring and dimple insert tube is mounted within the instrumentation tube thimble and extends downwardly adjacent the top. The springs and dimples restrain the sensor and its connections against lateral displacement causing impact with the instrumentation tube thimble due to the strong axial flow of cooling water. The instrumentation tube has a stainless steel outer sleeve and a zirconium alloy inner sleeve below the insert tube adjacent the top. The insert tube is relatively non-radioactivated inconel alloy. The opposed springs and dimples are formed on diametrically opposite inner walls of the insert tube, the springs being formed as spaced axial cuts in the insert tube, with a web of the insert tube between the cuts bowed radially inwardly for forming the spring, and the dimples being formed as radially inward protrusions opposed to the springs.

  4. Settling time of dental x-ray tube head after positioning

    Energy Technology Data Exchange (ETDEWEB)

    Yun, Suk Ja; Kang, Byung Cheol [Department of Oral and Maxillofacial Radiology, Chonnam National University, Gwangju (Korea, Republic of); Wang, Se Myung; Koh, Chang Sung [Department of Mechatronics, Kwangju Institute of Science and Technology, Gwangju (Korea, Republic of)

    2002-09-15

    The aim of this study was to introduce a method of obtaining the oscillation graphs of the dental x-ray tube heads relative to time using an accelerometer. An Accelerometer, Piezotron type 8704B25 (Kistler Instrument Co., Amherst, NY, USA) was utilized to measure the horizontal oscillation of the x-ray tube head immediately after positioning the tube head for an intraoral radiograph. The signal from the sensor was transferred to a dynamic signal analyzer, which displayed the magnitude of the acceleration on the Y-axis and time lapse on the X-axis. The horizontal oscillation of the tube head was measured relative to time, and the settling time was also determined on the basis of the acceleration graphs for 6 wall type, 5 floor-fixed type, and 4 mobile type dental x-ray machines. The oscillation graphs showed that tube head movement decreased rapidly over time. The settling time varied with x-ray machine types. Wall-type x-ray machines had a settling time of up to 6 seconds, 5 seconds for fixed floor-types, and 11 seconds for the mobile-types. Using an accelerometer, we obtained the oscillation graphs of the dental x-ray tube head relative to time. The oscillation graph with time can guide the operator to decide upon the optimum exposure moment after xray tube head positioning for better radiographic resolution.

  5. Glycoprotein composition along the pistil of Malus x domestica and the modulation of pollen tube growth.

    Science.gov (United States)

    Losada, Juan M; Herrero, Maria

    2014-01-03

    The characteristics of pollen tube growth are not constant, but display distinct patterns of growth within the different tissues of the pistil. In the stigma, the growth rate is slow and autotrophic, whereas in the style, it is rapid and heterotrophic. Very little is known about the interactions between these distinct maternal tissues and the traversing pollen tube and the role of this interaction on the observed metabolism. In this work we characterise pollen tube growth in the apple flower and look for differences in glycoprotein epitope localization between two different maternal tissues, the stigma and the style. While immunocytochemically-detected arabinogalactan proteins were present at high levels in the stigma, they were not detected in the transmitting tissue of the style, where extensins were abundant. Whereas extensins remained at high levels in unpollinated pistils, they were no longer present in the style following pollen tube passage. Similarily, while abundant in unpollinated styles, insoluble polysaccharides such as β-glucans, were depleted in pollinated pistils. The switch from autotropic to heterotrophic pollen tube growth correlates spatially with a change of glycoprotein epitopes between the stigma and the style. The depletion of extensins and polysaccharides following pollen tube passage in the style suggest a possible contribution to the acceleration of heterotrophic pollen tube growth, which would imply an active contribution of female tissues on prezygotic male-female crosstalk.

  6. Numerical and experimental study of an annular pulse tube used in the pulse tube cooler

    Science.gov (United States)

    Pang, Xiaomin; Chen, Yanyan; Wang, Xiaotao; Dai, Wei; Luo, Ercang

    2017-12-01

    Multi-stage pulse tube coolers normally use a U-type configuration. For compactness, it is attractive to build a completely co-axial multi-stage pulse tube cooler. In this way, an annular shape pulse tube is inevitable. Although there are a few reports about previous annular pulse tubes, a detailed study and comparison with a circular pulse tube is lacking. In this paper, a numeric model based on CFD software is carried out to compare the annular pulse tube and circular pulse tube used in a single stage in-line type pulse tube cooler with about 10 W of cooling power at 77 K. The length and cross sectional area of the two pulse tubes are kept the same. Simulation results show that the enthalpy flow in the annular pulse tube is lower by 1.6 W (about 11% of the enthalpy flow) compared to that in circular pulse tube. Flow and temperature distribution characteristics are also analyzed in detail. Experiments are then conducted for comparison with an in-line type pulse tube cooler. With the same acoustic power input, the pulse tube cooler with a circular pulse tube obtains 7.88 W of cooling power at 77 K, while using an annular pulse tube leads to a cooling power of 7.01 W, a decrease of 0.9 W (11.4%) on the cooling performance. The study sets the basis for building a completely co-axial two-stage pulse tube cooler.

  7. ATLS: Catheter and tube placement

    Science.gov (United States)

    Gosbee, John; Krupa, Debra T.; Pepper, L.; Orsak, Debra

    1991-01-01

    The specific objectives of this experiment are: to evaluate the rack mounted equipment and medical supplies necessary for medical procedures; to evaluate the attachments, mounting points, and inner drawer assemblies for the medical supplies; and to evaluate the procedures for performing medical scenarios. The resources available in the HMF miniracks to accomplish medical scenarios and/or procedures include: medical equipment mounted in the racks; a patch panel with places to attach tubing and catheters; self contained drawers full of critical care medical supplies; and an ALS 'backpack' for deploying supplies. The attachment lines, tubing and associated medical supplies will be deployed and used with the equipment and a patient mannequin. Data collection is provided by direct observations by the inflight experimenters, and analysis of still and video photography.

  8. AFRL Ludwieg Tube Initial Performance

    Science.gov (United States)

    2017-11-01

    controls the fill and purge process. A commercial Sylvania 18 kW resistance heater raises the inlet air temperature to 500K prior to filling the...Distribution is unlimited. 3 ms of uniform run conditions between wave passages. The exterior of the driver tube is heated with blanket resistance ...uniformity and noise characteristics, this has not been a major problem with wind tunnels using this type of valve. However, there has been no direct

  9. Preliminary display comparison for dental diagnostic applications

    Science.gov (United States)

    Odlum, Nicholas; Spalla, Guillaume; van Assche, Nele; Vandenberghe, Bart; Jacobs, Reinhilde; Quirynen, Marc; Marchessoux, Cédric

    2012-02-01

    The aim of this study is to predict the clinical performance and image quality of a display system for viewing dental images. At present, the use of dedicated medical displays is not uniform among dentists - many still view images on ordinary consumer displays. This work investigated whether the use of a medical display improved the perception of dental images by a clinician, compared to a consumer display. Display systems were simulated using the MEdical Virtual Imaging Chain (MEVIC). Images derived from two carefully performed studies on periodontal bone lesion detection and endodontic file length determination, were used. Three displays were selected: a medical grade one and two consumer displays (Barco MDRC-2120, Dell 1907FP and Dell 2007FPb). Some typical characteristics of the displays are evaluated by measurements and simulations like the Modulation Function (MTF), the Noise Power Spectrum (NPS), backlight stability or calibration. For the MTF, the display with the largest pixel pitch has logically the worst MTF. Moreover, the medical grade display has a slightly better MTF and the displays have similar NPS. The study shows the instability effect for the emitted intensity of the consumer displays compared to the medical grade one. Finally the study on the calibration methodology of the display shows that the signal in the dental images will be always more perceivable on the DICOM GSDF display than a gamma 2,2 display.

  10. The case for transparent depth display

    NARCIS (Netherlands)

    Kooi, F.L.

    2003-01-01

    Purpose: The continuing developments in display technology have resulted in the ability to present increasing amounts of data on computer displays. One of the coming break-throughs is generally believed to be the introduction of '3-D displays': displays with a true sense of depth. Though these types

  11. Density Gradient Columns for Chemical Displays.

    Science.gov (United States)

    Guenther, William B.

    1986-01-01

    Procedures for preparing density gradient columns for chemical displays are presented. They include displays illustrating acid-base reactions, metal ion equilibria, and liquid density. The lifetime of these metastable displays is surprising, some lasting for months in display cabinets. (JN)

  12. 40 CFR 90.907 - Display exemption.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Display exemption. 90.907 Section 90... of Nonroad Engines from Regulations § 90.907 Display exemption. Where an uncertified nonroad engine is a display engine to be used solely for display purposes, will only be operated incident and...

  13. 40 CFR 85.1707 - Display exemption.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Display exemption. 85.1707 Section 85... Engines § 85.1707 Display exemption. Where an uncertified vehicle or engine is a display vehicle or engine to be used solely for display purposes, will not be operated on the public streets or highways except...

  14. Full color waveguide liquid crystal display.

    Science.gov (United States)

    Zhou, Xiaochen; Qin, Guangkui; Wang, Long; Chen, Zhuo; Xu, Xiaoguang; Dong, Youmei; Moheghi, Alireza; Yang, Deng-Ke

    2017-09-15

    We developed a waveguide liquid crystal display from a liquid crystal (LC)/polymer composite. It does not need polarizers or color filters. It is illuminated by color LEDs installed on its edge. The light produced by the edge LEDs is coupled into the display and then waveguided through the display. When the LC is in the transparent state, the incident light is waveguided through and no light comes out of the viewing side of the display. When the LC is in the scattering state, the incident light is scattered and comes out of the display. It can be used either for transparent display or for direct view display. The composite has a submillisecond response time, and a field sequential scheme can be used to display full color images. Because the display does not need polarizers or color filters, its energy efficiency is much higher than current liquid crystal displays.

  15. Management practices for end-of-life cathode ray tube glass: Review of advances in recycling and best available technologies.

    Science.gov (United States)

    Iniaghe, Paschal O; Adie, Gilbert U

    2015-11-01

    Cathode ray tubes are image display units found in computer monitors and televisions. In recent years, cathode ray tubes have been generated as waste owing to the introduction of newer and advanced technologies in image displays, such as liquid crystal displays and high definition televisions, among others. Generation and subsequent disposal of end-of-life cathode ray tubes presents a challenge owing to increasing volumes and high lead content embedded in the funnel and neck sections of the glass. Disposal in landfills and open dumping are anti-environmental practices considering the large-scale contamination of environmental media by the potential of toxic metals leaching from glass. Mitigating such environmental contamination will require sound management strategies that are environmentally friendly and economically feasible. This review covers existing and emerging management practices for end-of-life cathode ray tubes. An in-depth analysis of available technologies (glass smelting, detoxification of cathode ray tube glass, lead extraction from cathode ray tube glass) revealed that most of the techniques are environmentally friendly, but are largely confined to either laboratory scale, or are often limited owing to high cost to mount, or generate secondary pollutants, while a closed-looped method is antiquated. However, recycling in cementitious systems (cement mortar and concrete) gives an added advantage in terms of quantity of recyclable cathode ray tube glass at a given time, with minimal environmental and economic implications. With significant quantity of waste cathode ray tube glass being generated globally, cementitious systems could be economically and environmentally acceptable as a sound management practice for cathode ray tube glass, where other technologies may not be applicable. © The Author(s) 2015.

  16. Tube entrance lens focus control

    Science.gov (United States)

    Weisser, D. C.; Fifield, L. K.; Kitchen, T. F. G.; Tunningley, T. B.; Lobanov, N. R.; Muirhead, A. G.

    2013-02-01

    The entrance of the accelerator tube in a large electrostatic accelerator imposes a strong lens that dominates the beam optics. The magnification of the lens is large because of the low injection energy, the high voltage gradient of the acceleration tube and the long distance to the terminal. In the absence of the acceleration, the magnification would produce an unacceptably large beam spot at the terminal. The tyranny of the lens is especially irksome when the accelerator is required to operate at a lower terminal voltage than the one corresponding to the nominal gradient at high voltage. One way around the difficulty, used in NEC Pelletron accelerators, is to insert a series of nylon and steel rods that short together units of the acceleration structure at the terminal leaving the ones near the entrance close to the nominal gradient for optimum transmission. This operation takes time and risks the loss of insulating gas. Another alternative used in the 25URC at Oak Ridge National Laboratory, is to focus the beam at the tube entrance, substantially diluting the effect of the entrance lens. The beam then diverges and so requires an additional lens part way to the terminal. This solution is only partially effective and still necessitates use of shorting rods for low voltage operation. The fact that these elaborate strategies are used is evidence that the alternative of lowering the injection energy as the terminal voltage is lowered imposes enough problems that it is not used in practice. We have modeled a solution that controls the voltage gradient at the tube entrance using an external power supply. This not only maintains the focusing effect of the lens but provides the opportunity to tune the beam by adjusting the entrance lens. A 150 kV power supply outside the pressure vessel feeds a controllable voltage through a high voltage feed-through to the fifth electrode of the accelerator tube. Thus 150 kV on this electrode creates the nominal gradient of 30 kV per

  17. Gastroenteric tube feeding: Techniques, problems and solutions

    Science.gov (United States)

    Blumenstein, Irina; Shastri, Yogesh M; Stein, Jürgen

    2014-01-01

    Gastroenteric tube feeding plays a major role in the management of patients with poor voluntary intake, chronic neurological or mechanical dysphagia or gut dysfunction, and patients who are critically ill. However, despite the benefits and widespread use of enteral tube feeding, some patients experience complications. This review aims to discuss and compare current knowledge regarding the clinical application of enteral tube feeding, together with associated complications and special aspects. We conducted an extensive literature search on PubMed, Embase and Medline using index terms relating to enteral access, enteral feeding/nutrition, tube feeding, percutaneous endoscopic gastrostomy/jejunostomy, endoscopic nasoenteric tube, nasogastric tube, and refeeding syndrome. The literature showed common routes of enteral access to include nasoenteral tube, gastrostomy and jejunostomy, while complications fall into four major categories: mechanical, e.g., tube blockage or removal; gastrointestinal, e.g., diarrhea; infectious e.g., aspiration pneumonia, tube site infection; and metabolic, e.g., refeeding syndrome, hyperglycemia. Although the type and frequency of complications arising from tube feeding vary considerably according to the chosen access route, gastrointestinal complications are without doubt the most common. Complications associated with enteral tube feeding can be reduced by careful observance of guidelines, including those related to food composition, administration rate, portion size, food temperature and patient supervision. PMID:25024606

  18. Development boiling to sprinkled tube bundle

    Directory of Open Access Journals (Sweden)

    Kracík Petr

    2016-01-01

    Full Text Available This paper presents results of a studied heat transfer coefficient at the surface of a sprinkled tube bundle where boiling occurs. Research in the area of sprinkled exchangers can be divided into two major parts. The first part is research on heat transfer and determination of the heat transfer coefficient at sprinkled tube bundles for various liquids, whether boiling or not. The second part is testing of sprinkle modes for various tube diameters, tube pitches and tube materials and determination of individual modes’ interface. All results published so far for water as the falling film liquid apply to one to three tubes for which the mentioned relations studied are determined in rigid laboratory conditions defined strictly in advance. The sprinkled tubes were not viewed from the operational perspective where there are more tubes and various modes may occur in different parts with various heat transfer values. The article focuses on these processes. The tube is located in a low-pressure chamber where vacuum is generated using an exhauster via ejector. The tube consists of smooth copper tubes of 12 mm diameter placed horizontally one above another.

  19. Plastic Substrates for Flexible Displays

    Science.gov (United States)

    Ito, Hisashi; Oka, Wataru; Goto, Hideki; Umeda, Hideo

    2006-05-01

    New flexible fibrous glass-reinforced plastic (FRP) substrates for flat panel displays were developed. Optimizing the composition of the FRP by adjusting the difference in refractive index between a matrix resin and a glass fiber enabled the coexistence of a high transparency and a low coefficient of thermal expansion (CTE). An excellent smooth surface morphology was confirmed by the formulation of a coating resin. The stability of moisture impermeability depended on the surface smoothness and adhesion between a barrier layer and the coating layer. The moisture permeation rates of barrier substrates were below detection limits (<0.01 g m-2 day-1) on standard measurement equipment.

  20. Carbon nano tubes -Buckypaper- radiation studies for medical physics application

    Energy Technology Data Exchange (ETDEWEB)

    Alanazi, A.; Alkhorayef, M.; Dalton, A.; Bradley, D. A. [University of Surrey, Department of Physics, College for Nuclear and Radiation Physics, Guildford, Surrey GR2 7XH (United Kingdom); Alzimami, K. [King Saud University, Department of Radiological Sciences, P. O. Box 10219, Riyadh 11433 (Saudi Arabia); Abuhadi, N., E-mail: a.alanazi@surrey.ac.uk [Jazan University, Faculty of Medical Applied Sciences, Diagnostic Radiology Department, P. O. Box 114, Jazan (Saudi Arabia)

    2015-10-15

    Radiation dosimetry underpins safe and effective clinical applications of radiation. Many materials have been used to measure the radiation dose deposited in human tissue, their radiation response requiring the application of correction factors to account for various influencing factors, including sensitivity to dose and energy dependence. In regard to the latter, account needs to be taken of difference from the effective atomic number of human tissue, soft or calcified. Graphite ion chambers and semiconductor diode detectors have been used to make measurements in phantoms but these active devices represent a clear disadvantage when considered for in vivo dosimetry. In both circumstances, dosimeters with atomic number similar to human tissue are needed. Carbon nano tubes have properties that potentially meet the demand, requiring low voltage in active devices and an atomic number similar to adipose tissue. In this study, single-wall carbon nano tubes buckypaper has been used to measure the beta particle dose deposited from a strontium-90 source, the medium displaying thermoluminescence at potentially useful sensitivity. As an example, the samples show a clear response for a dose of 2 Gy. This finding suggests that carbon nano tubes can be used as a passive dosimeter specifically for the high levels of radiation exposures used in radiation therapy. Furthermore, the finding points towards further potential applications such as for space radiation measurements, not least because the medium satisfies a demand for light but strong materials of minimal capacitance. (Author)

  1. Comparison of complication rates, types, and average tube patency between jejunostomy tubes and percutaneous gastrostomy tubes in a regional home enteral nutrition support program.

    Science.gov (United States)

    Ao, Peter; Sebastianski, Meghan; Selvarajah, Vijeyakumar; Gramlich, Leah

    2015-06-01

    Percutaneous endoscopic gastrostomy (PEG) tubes are common enteral access devices for long-term enteral nutrition. Jejunostomy tubes (J-tubes) are able to provide postpyloric enteral access in patients who are not PEG tube candidates. There is a scarcity of literature comparing complication rates of J-tubes to PEG tubes. To compare and characterize J-tube and PEG tube complications requiring tube replacement. A retrospective chart review was performed on 560 patients discharged from the Northern Alberta Home Enteral Nutrition Support Program (NAHENSP) from January 2010 to December 2011. Patients were followed for 3 years from initial tube insertion or until discharge from the NAHENSP, whichever was earliest. Comparisons were made in terms of complications requiring tube replacement, tube patency to first replacement, and indications for tube replacement. A total of 64 J-tube patients were identified and compared with 65 PEG tube patients. Tube replacement rates for the J-tube group included 3.2 cases per 1000 patient days compared with 0.86 cases per 1000 patient days in the PEG group (P < .001). The mean ± SEM duration to first tube replacement for J-tube and PEG tube patients was 160 ± 26.3 days and 331 ± 53.6 days, respectively (P = .010). The most common causes for tube replacement in J-tube patients were dislodgement (35.6%) and obstruction (22.2%) compared with routine replacement (54.5%) and dislodgement (27.2%) in the PEG tube group. J-tubes are associated with higher complication rates requiring tube replacement compared with PEG tubes. The main causes of J-tube replacement are dislodgement and obstruction. © 2014 American Society for Parenteral and Enteral Nutrition.

  2. Effect of tube-support interaction on the dynamic responses of heat exchanger tubes. [LMFBR

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Y.S.; Jendrzejczyk, J.A.; Wambsganss, M.W.

    1977-01-01

    Operating heat exchangers have experienced tube damages due to excessive flow-induced vibration. The relatively small inherent tube-to-baffle hole clearances associated with manufacturing tolerances in heat exchangers affect the tube vibrational characteristics. In attempting a theoretical analysis, questions arise as to the effects of tube-baffle impacting on dynamic responses. Experiments were performed to determine the effects of tube-baffle impacting in vertical/horizontal tube orientation, and in air/water medium on the vibrational characteristics (resonant frequencies, mode shapes, and damping) and displacement response amplitudes of a seven-span tube model. The tube and support conditions were prototypic, and overall length approximately one-third that of a straight tube segment of the steam generator designed for the CRBR. The test results were compared with the analytical results based on the multispan beam with ''knife-edge'' supports.

  3. Multi-tube arrangement for combustor and method of making the multi-tube arrangement

    Energy Technology Data Exchange (ETDEWEB)

    Ziminsky, Willy Steve [Simpsonville, SC

    2012-07-31

    A fuel injector tube includes a one piece, unitary, polygonal tube having an inlet end and an outlet end. The fuel injector tube further includes a fuel passage extending from the inlet end to the outlet end along a longitudinal axis of the polygonal tube, a plurality of air passages extending from the inlet end to the outlet end and surrounding the fuel passage, and a plurality of fuel holes. Each fuel hole connects an air passage with the fuel passage. The inlet end of the polygonal tube is formed into a fuel tube. A fuel injector includes a plurality of fuel injector tubes and a plate. The plurality of fuel tubes are connected to the plate adjacent the inlet ends of the plurality of fuel injector tubes.

  4. Routine jejunostomy tube feeding following esophagectomy

    Science.gov (United States)

    van Eden, Hanneke W. J.; Ruurda, Jelle P.; Luyer, Misha D. P.; Steenhagen, Elles; Nieuwenhuijzen, Grard A. P.; van Hillegersberg, Richard

    2017-01-01

    Background Malnutrition is an important problem following esophagectomy. A surgically placed jejunostomy secures an enteral feeding route, facilitating discharge with home-tube feeding and long-term nutritional support. However, specific complications occur, and data are lacking that support its use over other enteral feeding routes. Therefore routine jejunostomy tube feeding and discharge with home-tube feeding was evaluated, with emphasis on weight loss, length of stay and re-admissions. Methods Consecutive patients undergoing esophagectomy for cancer, with gastric tube reconstruction and jejunostomy creation, were analyzed. Two different regimens were compared. Before January 07, 2011 patients were discharged when oral intake was sufficient, without tube feeding. After that discharge with home-tube feeding was routinely performed. Logistic regression analysis corrected for confounders. Results Some 236 patients were included. The median duration of tube feeding was 35 days. Reoperation for a jejunostomy-related complication was needed in 2%. The median body mass index (BMI) remained stable during tube feeding. The BMI decreased significantly after stopping tube feeding: from 25.6 (1st–3rd quartile 23.0–28.6) kg/m2 to 24.4 (22.0–27.1) kg/m2 at 30 days later [median weight loss: 3.0 (1.0–5.3) kg; 3.9% (1.5–6.3%)]. Weight loss was not affected by the duration of tube feeding duration. Routine home-tube feeding did not affect weight loss, admission time or the readmission rate. Conclusions Weight loss following esophagectomy occurs once that tube feeding is stopped, independently from the time interval after esophagectomy. Moreover routine discharge with home-tube feeding does not reduce length of stay or readmissions. These findings question the value of routine jejunostomy placement and emphasize the need for further research. PMID:28815083

  5. Development of INCONEL 600 precision tube (1)

    Energy Technology Data Exchange (ETDEWEB)

    Joo, Yeong Han; Jo, Bong Hyeon; Lee, Dong Hee; Kim, Wan Kyo; Jeong, Pyeong Keun; Yoon, Hwang Lo; Chio, Seok Sik [Sammi Steel Co. Ltd., Changwon (Korea, Republic of)

    1994-07-01

    Steam generator, being connected with nuclear fuel reactor is one of the most important part of nuclear power plant and consists of a large number of INCONEL 600 tubes. Approximately 160 tons of tubes are needed for a single nuclear power plant. All of INCONEL 600 steam generator tubes for domestic nuclear power plants have been imported. The aim of this research is to develop INCONEL 600 precision tubes for steam generator of nuclear power plant. If this research is conducted successfully, we can produce nuclear fuel tubes, Ni-alloy precision tubes and stainless steel precision tubes for many purposes and technology of INCONEL 600 steam generator tubes are similar to those of other tubes above mentioned. In the current study, development of preliminary manufacturing process of INCONEL 600 precision tubes for steam generator and investigation of material`s metallurgical characteristics were conducted. The main scope of this research is as follows. First, the preliminary manufacturing process design was conducted after investigations of foreign manufacturing processes and technical reports. Second, the results of investigations of material`s metallurgical characteristics through the manufacturing process were applied to the production technology of tentative INCONEL 600 precision tubes for sample. Third, preliminary process routes were established and samples of INCONEL 600 precision tube were produced by this process. As the results of this research, 14 pieces of INCONEL 600 precision tubes were produced by preliminary manufacturing process and the material`s metallurgical characteristics were investigated through the processes. But the SCC test could not be conducted due to the absence of equipment. In order to apply the results of SCC test to the manufacturing process, we need a SCC tester which can simulate SCC characteristics under high temperature and high pressurized circulating water. 95 refs., 55 figs., 20 tabs.

  6. Cases of fallopian tube prolapse

    Directory of Open Access Journals (Sweden)

    Sushil Chawla

    2015-01-01

    Full Text Available Fallopian tube prolapse post hysterectomy is rarely reported complication which can lead to doubts in the mind of young and experienced surgeons alike. This leads to patient morbidity and gets different medical treatments ranging from antibiotics to local applications of copper sulphate, without relief. The use of proper surgical technique, prevention of post operative hematoma and infection go a long way in its prevention.We hereby present two cases, which were manged successfully to relieve the patients of their agony.

  7. Comparison of primary jejunostomy tubes versus gastrojejunostomy tubes for percutaneous enteral nutrition.

    Science.gov (United States)

    Kim, Charles Y; Engstrom, Bjorn I; Horvath, Jeffrey J; Lungren, Matthew P; Suhocki, Paul V; Smith, Tony P

    2013-12-01

    To evaluate technical success and long-term outcomes of percutaneous primary jejunostomy tubes for postpyloric enteral feeding compared with percutaneous gastrojejunostomy (GJ) tubes. Over a 25-month interval, 41 consecutive patients (26 male; mean age, 55.9 y) underwent attempted fluoroscopy-guided direct percutaneous jejunostomy tube insertion. Insertions at previous jejunostomy tube sites were excluded. The comparison group consisted of all primary GJ tube insertions performed over a 12-month interval concomitant with the jejunostomy tube interval (N = 169; 105 male; mean age, 59.4 y). Procedural, radiologic, and clinical data were retrospectively reviewed. Intervention rates were expressed as events per 100 catheter-days. The technical success rate for percutaneous jejunostomy tube insertion was 96%, versus 93% for GJ tubes (P = .47). Mean fluoroscopy times were similar for jejunostomy and GJ tubes (9.8 vs 10.0 min, respectively; P value not significant). Jejunostomy tubes exhibited a lower rate of catheter dysfunction than GJ tubes, with catheter exchange rates of 0.24 versus 0.93, respectively, per 100 catheter-days (P = .045). GJ tube tip retraction into the stomach occurred in 9.5% of cases, at a rate of 0.21 per 100 catheter-days. Intervention rates related to leakage were 0.19 and 0.03 for jejunostomy and GJ tubes, respectively (P Jejunostomy and GJ tubes exhibited similar rates of catheter exchange for occlusion and replacement as a result of inadvertent removal. No major complications were encountered in either group. Percutaneous insertion of primary jejunostomy tubes demonstrated technical success and complication rates similar to those of GJ tubes. Jejunostomy tubes exhibited a lower dysfunction rate but a higher leakage rate compared with GJ tubes. Copyright © 2013 SIR. Published by Elsevier Inc. All rights reserved.

  8. Interruption and Pausing of Public Display Games

    DEFF Research Database (Denmark)

    Feuchtner, Tiare; Walter, Robert; Müller, Jörg

    2016-01-01

    We present a quantitative and qualitative analysis of interruptions of interaction with a public display game, and explore the use of a manual pause mode in this scenario. In previous public display installations we observed users frequently interrupting their interaction. To explore ways...... that interactions with public displays are considerably intermissive, and that users mostly interrupt interaction to socialize and mainly approach public displays in groups. We conclude that, as a typical characteristic of public display interaction, interruptions deserve consideration. However, manual pause modes...... are not well suited for games on public displays. Instead, interruptions should be implicitly supported by the application design....

  9. Display elements and gaps: a comparison of flat panel display characteristics

    NARCIS (Netherlands)

    Spenkelink, G.P.J.; Besuijen, J.

    1992-01-01

    The relation between typical flat panel display characteristics and display quality was studied. Subjective preferences were obtained with respect to simulated black-on-white flat panel displays. The displays differed in the sort of separation between the display elements and the shape of these

  10. Differences in displayed pump flow compared to measured flow under varying conditions during simulated cardiopulmonary bypass.

    LENUS (Irish Health Repository)

    Hargrove, M

    2008-07-01

    Errors in blood flow delivery due to shunting have been reported to reduce flow by, potentially, up to 40-83% during cardiopulmonary bypass. The standard roller-pump measures revolutions per minute and a calibration factor for different tubing sizes calculates and displays flow accordingly. We compared displayed roller-pump flow with ultrasonically measured flow to ascertain if measured flow correlated with the heart-lung pump flow reading. Comparison of flows was measured under varying conditions of pump run duration, temperature, viscosity, varying arterial\\/venous loops, occlusiveness, outlet pressure, use of silicone or polyvinyl chloride (PVC) in the roller race, different tubing diameters, and use of a venous vacuum-drainage device.

  11. Minimalism context-aware displays.

    Science.gov (United States)

    Cai, Yang

    2004-12-01

    Despite the rapid development of cyber technologies, today we still have very limited attention and communication bandwidth to process the increasing information flow. The goal of the study is to develop a context-aware filter to match the information load with particular needs and capacities. The functions include bandwidth-resolution trade-off and user context modeling. From the empirical lab studies, it is found that the resolution of images can be reduced in order of magnitude if the viewer knows that he/she is looking for particular features. The adaptive display queue is optimized with real-time operational conditions and user's inquiry history. Instead of measuring operator's behavior directly, ubiquitous computing models are developed to anticipate user's behavior from the operational environment data. A case study of the video stream monitoring for transit security is discussed in the paper. In addition, the author addresses the future direction of coherent human-machine vision systems.

  12. Simplified Night Sky Display System

    Science.gov (United States)

    Castellano, Timothy P.

    2010-01-01

    A document describes a simple night sky display system that is portable, lightweight, and includes, at most, four components in its simplest configuration. The total volume of this system is no more than 10(sup 6) cm(sup 3) in a disassembled state, and weighs no more than 20 kilograms. The four basic components are a computer, a projector, a spherical light-reflecting first surface and mount, and a spherical second surface for display. The computer has temporary or permanent memory that contains at least one signal representing one or more images of a portion of the sky when viewed from an arbitrary position, and at a selected time. The first surface reflector is spherical and receives and reflects the image from the projector onto the second surface, which is shaped like a hemisphere. This system may be used to simulate selected portions of the night sky, preserving the appearance and kinesthetic sense of the celestial sphere surrounding the Earth or any other point in space. These points will then show motions of planets, stars, galaxies, nebulae, and comets that are visible from that position. The images may be motionless, or move with the passage of time. The array of images presented, and vantage points in space, are limited only by the computer software that is available, or can be developed. An optional approach is to have the screen (second surface) self-inflate by means of gas within the enclosed volume, and then self-regulate that gas in order to support itself without any other mechanical support.

  13. Narratives From YouTube

    Directory of Open Access Journals (Sweden)

    Mikael Quennerstedt

    2013-10-01

    Full Text Available The aim of this paper is to explore what is performed in students’ and teachers’ actions in physical education practice in terms of “didactic irritations,” through an analysis of YouTube clips from 285 PE lessons from 27 different countries. Didactic irritations are occurrences that Rønholt describes as those demanding “didactic, pedagogical reflections and discussions, which in turn could lead to alternative thinking and understanding about teaching and learning.” Drawing on Barad’s ideas of performativity to challenge our habitual anthropocentric analytical gaze when looking at educational visual data, and using narrative construction, we also aim to give meaning to actions, relations, and experiences of the participants in the YouTube clips. To do this, we present juxtaposing narratives from teachers and students in terms of three “didactic irritations”: (a stories from a track, (b, stories from a game, and (c, stories from a bench. The stories re-present events-of-moving in the data offering insights into embodied experiences in PE practice, making students’ as well as teachers’ actions in PE practice understandable.

  14. [Enteral feeding tubes for critically ill patients].

    Science.gov (United States)

    Braun, J; Bein, T; Wiese, C H R; Graf, B M; Zausig, Y A

    2011-04-01

    The use of enteral feeding tubes is an important part of early enteral feeding in intensive care medicine. In other faculties with non-critically ill patients, such as (oncologic) surgery, neurology, paediatrics or even in palliative care medicine feeding tubes are used under various circumstances as a temporary or definite solution. The advantage of enteral feeding tubes is the almost physiologic administration of nutrition, liquids and medication. Enteral nutrition is thought to be associated with a reduced infection rate, increased mucosal function, improved immunologic function, reduced length of hospital stay and reduced costs. However, the insertion and use of feeding tubes is potentially dangerous and may be associated with life-threatening complications (bleeding, perforation, peritonitis, etc.). Therefore, the following article will give a summary of the different types of enteral feeding tubes and their range of application. Additionally, a critical look on indication and contraindication is given as well as how to insert an enteral feeding tube.

  15. Why do aged fluorescent tubes flicker?

    Science.gov (United States)

    Plihon, Nicolas; Ferrand, Jérémy; Guyomar, Tristan; Museur, Flavien; Taberlet, Nicolas

    2017-11-01

    Our everyday experience of aged and defective fluorescent tubes or bulbs informs us that they may flicker and emit a clicking sound while struggling to light up. In this article, the physical mechanisms controlling the initial illumination of a functioning fluorescent tube are investigated using a simple and affordable experimental setup. Thermionic emission from the electrodes of the tube controls the startup of fluorescent tubes. The origin of the faulty startup of aged fluorescent tubes is discussed and flickering regimes using functional tubes are artificially produced using a dedicated setup that decreases electron emission by the thermionic effect in a controlled manner. The physical parameters controlling the occurrence of flickering light are discussed, and their temporal statistics are reported.

  16. Holographic Waveguided See-Through Display Project

    Data.gov (United States)

    National Aeronautics and Space Administration — To address the NASA need for lightweight, space suit-mounted displays, Luminit proposes a novel Holographic Waveguided See-Through Display. Our proposed Holographic...

  17. Projection/Reflection Heads-up Display

    Data.gov (United States)

    National Aeronautics and Space Administration — To address the NASA need for an EVA information display device, Physical Optics Corporation (POC) proposes to develop a new Projection/Reflection Heads-up Display...

  18. OZ: An Innovative Primary Flight Display Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed SBIR project will develop OZ, an innovative primary flight display for aircraft. The OZ display, designed from "first principles" of vision science,...

  19. X-Windows Widget for Image Display

    Science.gov (United States)

    Deen, Robert G.

    2011-01-01

    XvicImage is a high-performance XWindows (Motif-compliant) user interface widget for displaying images. It handles all aspects of low-level image display. The fully Motif-compliant image display widget handles the following tasks: (1) Image display, including dithering as needed (2) Zoom (3) Pan (4) Stretch (contrast enhancement, via lookup table) (5) Display of single-band or color data (6) Display of non-byte data (ints, floats) (7) Pseudocolor display (8) Full overlay support (drawing graphics on image) (9) Mouse-based panning (10) Cursor handling, shaping, and planting (disconnecting cursor from mouse) (11) Support for all user interaction events (passed to application) (12) Background loading and display of images (doesn't freeze the GUI) (13) Tiling of images.

  20. National Weather Service: Watch, Warning, Advisory Display

    Science.gov (United States)

    ... Contact Us SPC Feedback NWS Watch, Warning, Advisory Display NWS Warnings and Advisories on this map become ... below): A new browser window will open to display these text products. Convective/Tropical Weather Flooding Winter ...

  1. DEVELOPMENT OF COILED TUBING STRESS ANALYSIS

    Directory of Open Access Journals (Sweden)

    Davorin Matanović

    1998-12-01

    Full Text Available The use of coiled tubing is increasing rapidly with drilling of horizontal wells. To satisfy all requirements (larger mechanical stresses, larger fluid capacities the production of larger sizes and better material qualities was developed. Stresses due to axial forces and pressures that coiled tubing is subjected are close to its performance limits. So it is really important to know and understand the behaviour of coiled tubing to avoid its break, burst or collapse in the well.

  2. Medication administration through enteral feeding tubes.

    Science.gov (United States)

    Williams, Nancy Toedter

    2008-12-15

    An overview of enteral feeding tubes, drug administration techniques, considerations for dosage form selection, common drug interactions with enteral formulas, and methods to minimize tube occlusion is given. Enteral nutrition through a feeding tube is the preferred method of nutrition support in patients who have a functioning gastrointestinal tract but who are unable to be fed orally. This method of delivering nutrition is also commonly used for administering medications when patients cannot swallow safely. However, several issues must be considered with concurrent administration of oral medications and enteral formulas. Incorrect administration methods may result in clogged feeding tubes, decreased drug efficacy, increased adverse effects, or drug-formula incompatibilities. Various enteral feeding tubes are available and are typically classified by site of insertion and location of the distal tip of the feeding tube. Liquid medications, particularly elixirs and suspensions, are preferred for enteral administration; however, these formulations may be hypertonic or contain large amounts of sorbitol, and these properties increase the potential for adverse effects. Before solid dosage forms are administered through the feeding tube, it should be determined if the medications are suitable for manipulation, such as crushing a tablet or opening a capsule. Medications should not be added directly to the enteral formula, and feeding tubes should be properly flushed with water before and after each medication is administered. To minimize drug-nutrient interactions, special considerations should be taken when administering phenytoin, carbamazepine, warfarin, fluoroquinolones, and proton pump inhibitors via feeding tubes. Precautions should be implemented to prevent tube occlusions, and immediate intervention is required when blockages occur. Successful drug delivery through enteral feeding tubes requires consideration of the tube size and placement as well as careful

  3. Unique removal of a kinked nasogastric tube

    Directory of Open Access Journals (Sweden)

    Kumar Shwetanshu Narayan

    2017-01-01

    Full Text Available Nasogastric (NG tube insertion is a common clinical procedure used for both diagnostic and therapeutic purposes. As the importance of enteral nutrition is being increasingly recognized; the use of NG tube insertion has steadily increased. Here, we present an interesting case in which a kinked NG tube was removed in a unique manner with “push and pull” technique without untoward trauma.

  4. Preparation of nitrogen-doped carbon tubes

    Science.gov (United States)

    Chung, Hoon Taek; Zelenay, Piotr

    2015-12-22

    A method for synthesizing nitrogen-doped carbon tubes involves preparing a solution of cyanamide and a suitable transition metal-containing salt in a solvent, evaporating the solvent to form a solid, and pyrolyzing the solid under an inert atmosphere under conditions suitable for the production of nitrogen-doped carbon tubes from the solid. Pyrolyzing for a shorter period of time followed by rapid cooling resulted in a tubes with a narrower average diameter.

  5. Inverse Kinematics of Concentric Tube Steerable Needles

    OpenAIRE

    Sears, Patrick; Dupont, Pierre E.

    2007-01-01

    Prior papers have introduced steerable needles composed of precurved concentric tubes. The curvature and extent of these needles can be controlled by the relative rotation and translation of the individual tubes. Under certain assumptions on the geometry and design of these needles, the forward kinematics problem can be solved in closed form by means of algebraic equations. The inverse kinematics problem, however, is not as straightforward owing to the nonlinear map between relative tube disp...

  6. Approach of organic light-emitting displays (OLED) to technology status

    Science.gov (United States)

    Saini, Gurdial S.; Hopper, Darrel G.

    1998-09-01

    A display is an electronic component or subsystem used to convert electrical signals into visual imagery in real time suitable for direct interpretation by a human observer. Until recently, the cathode ray tube (CRT) has been the main source of displays. During the last twenty years, it has been determined that alternatives to CRT displays need to found. One of the alternatives was the introduction of flat-panel displays. The term 'flat-panel display' is more of a concept than a specific entity. It is a display which is flat and light and may not require a great deal of power. A flat-panel display is often defined in terms of the ideal display, that being: thin form, low volume, even surface, having high resolution, high contrast, sunlight readable, color, low power, and being solid-state, light weight, and low cost. This is easy to conceive but difficult to deliver. The objective is to develop displays with as many desirable characteristics as possible. Flat-panel displays are basically of two types: the light valve type (that needs an external source of light such as a backlight or arc-lamp) and the emissive type (that generate light at the display surface). The light emitting diode (LED) display is of the emissive type. Inorganic LED and electroluminescent (EL) displays have been in use for more than 25 years in one form or the other because of their 'inherent' ruggedness and operation over extremely wide temperature ranges. Because of certain limitations of inorganic materials (such as cost, power, and color), LED displays do not dominate the high information content flat- panel display market. A recent discovery of polymer and other organic materials has changed LED prospects. It may now be possible to make organic LED displays that are inexpensive, low-power, and at the same time provide high resolution and full color. If present research objectives are met, organic LEDs may revolutionize the flat-panel display market. This paper addresses the various aspects

  7. Psychological Implications for Submarine Display Design

    Science.gov (United States)

    2005-08-01

    This paper addresses a number of psychological issues pertaining to display design . We review the literature comparing 3-D and 2-D displays and...perceptual, cognitive and ecological factors that are relevant to display design for submarine environments. The Generative Transformational approach...to visual perception is outlined and the relevance of transformational theory to display design is discussed. The paper also discusses a number of

  8. Micro tube heat exchangers for Space Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Mezzo fabricates micro tube heat exchangers for a variety of applications, including aerospace, automotive racing, Department of Defense ground vehicles, economizers...

  9. Failure Analysis of a Service Tube

    Science.gov (United States)

    Xie, Zhongdong; Cai, Weiguo; Li, Zhenxing; Guan, YiMing; Zhang, Baocheng; Yang, XiaoTong

    2017-12-01

    One tube was cracked used in the primary reformer furnace in a fertilizer plant for two and half years. In order to find out the causes of cracking, the methods for chemical composition analysis, macro- and microstructure analysis, penetrant testing, weld analysis, crack and surface damage analysis, mechanics property analysis, high temperature endurance performance analysis, stress and wall thickness calculation were adopted. The integrated assessment results showed that the carbon content of the tube was in the lower limit of the standard range; the tube effective wall thickness was too small; local overheating leads to tube cracking in use process.

  10. Enhanced Evaporation and Condensation in Tubes

    Science.gov (United States)

    Honda, Hiroshi

    A state-of-the-art review of enhanced evaporation and condensation in horizontal microfin tubes and micro-channels that are used for air-conditioning and refrigeration applications is presented. The review covers the effects of flow pattern and geometrical parameters of the tubes on the heat transfer performance. Attention is paid to the effect of surface tension which leads to enhanced evaporation and condensation in the microfin tubes and micro-channels. A review of prior efforts to develop empirical correlations of the heat transfer coefficient and theoretical models for evaporation and condensation in the horizontal microfin tubes and micro-channels is also presented.

  11. How Visual Displays Affect Cognitive Processing

    Science.gov (United States)

    McCrudden, Matthew T.; Rapp, David N.

    2017-01-01

    We regularly consult and construct visual displays that are intended to communicate important information. The power of these displays and the instructional messages we attempt to comprehend when using them emerge from the information included in the display and by their spatial arrangement. In this article, we identify common types of visual…

  12. Directional light scanning 3-D display

    Science.gov (United States)

    Aoki, Yoji; Horimai, Hideyoshi; Lim, Pang Boey; Watanabe, Kenjiro; Inoue, Mitsuteru

    2009-11-01

    This paper presents a new Three-Dimensional display method, so called Directional Light Scanning 3D display. By using holographic screen as a beam scanner and high frame rate Spatial Light Modulator (SLM), this method requires only one SLM but can display high resolution 3D images, solving the usual problem of lack of resolution.

  13. Visual Merchandising through Display: Advertising Services Occupations.

    Science.gov (United States)

    Maurer, Nelson S.

    The increasing use of displays by businessmen is creating a demand for display workers. This demand may be met by preparing high school students to enter the field of display. Additional workers might be recruited by offering adult training programs for individuals working within the stores. For this purpose a curriculum guide has been developed…

  14. 27 CFR 6.55 - Display service.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Display service. 6.55... OF THE TREASURY LIQUORS âTIED-HOUSEâ Unlawful Inducements Paying for Advertising, Display Or Distribution Service § 6.55 Display service. Industry member reimbursements to retailers for setting up product...

  15. 9 CFR 392.6 - Public display.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Public display. 392.6 Section 392.6... INSPECTION SERVICE ADMINISTRATIVE PROVISIONS PETITIONS FOR RULEMAKING § 392.6 Public display. (a) All... information that should not be put on public display. If the petitioner fails to submit the certification...

  16. 14 CFR 21.161 - Display.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Display. 21.161 Section 21.161 Aeronautics... PROCEDURES FOR PRODUCTS AND PARTS Production Certificates § 21.161 Display. The holder of a production certificate shall display it prominently in the main office of the factory in which the product concerned is...

  17. Generation of flux tube waves in stellar convection zones. 1: Longitudinal tube waves

    Science.gov (United States)

    Musielak, Z. E.; Rosner, R.; Ulmschneider, P.

    1987-01-01

    The source functions and the energy fluxes are derived for wave generation in magnetic flux tubes embedded in an otherwise magnetic- field free, turbulent, and compressible fluid. Specific results for the generation of longitudinal tube waves are presented.

  18. Sunspots and the physics of magnetic flux tubes. V - Mutual hydrodynamic forces between neighboring tubes

    Science.gov (United States)

    Parker, E. N.

    1979-01-01

    The mutual hydrodynamic forces between parallel cylinders in a moving fluid are illustrated through several formal examples. Parallel tubes in a uniform flow are attracted or repelled depending on whether they are side by side or one ahead of the other, respectively. A pulsating or undulating tube attracts all other neighboring tubes toward itself. These hydrodynamic effects suggest that the separate flux tubes beneath the sunspots exert significant attractive forces on each other.

  19. A Sinuous Tumulus over an Active Lava Tube at Klauea Volcano: Evolution, Analogs, and Hazard Forecasts

    Science.gov (United States)

    Orr, Tim R.; Bleacher, Jacob E.; Patrick, Matthew R.; Wooten, Kelly M.

    2015-01-01

    Inflation of narrow tube-fed basaltic lava flows (tens of meters across), such as those confined by topography, can be focused predominantly along the roof of a lava tube. This can lead to the development of an unusually long tumulus, its shape matching the sinuosity of the underlying lava tube. Such a situation occurred during Klauea Volcanos (Hawaii, USA) ongoing East Rift Zone eruption on a lava tube active from July through November 2010. Short-lived breakouts from the tube buried the flanks of the sinuous, ridge-like tumulus, while the tumulus crest, its surface composed of lava formed very early in the flows emplacement history, remained poised above the surrounding younger flows. At least several of these breakouts resulted in irrecoverable uplift of the tube roof. Confined sections of the prehistoric Carrizozo and McCartys flows (New Mexico, USA) display similar sinuous, ridge-like features with comparable surface age relationships. We contend that these distinct features formed in a fashion equivalent to that of the sinuous tumulus that formed at Kilauea in 2010. Moreover, these sinuous tumuli may be analogs for some sinuous ridges evident in orbital images of the Tharsis volcanic province on Mars. The short-lived breakouts from the sinuous tumulus at Kilauea were caused by surges in discharge through the lava tube, in response to cycles of deflation and inflation (DI events) at Kilauea's summit. The correlation between DI events and subsequent breakouts aided in lava flow forecasting. Breakouts from the sinuous tumulus advanced repeatedly toward the sparsely populated Kalapana Gardens subdivision, destroying two homes and threatening others. Hazard assessments, including flow occurrence and advance forecasts, were relayed regularly to the Hawai?i County Civil Defense to aid their lava flow hazard mitigation efforts while this lava tube was active.

  20. CERN students display their work

    CERN Multimedia

    Anaïs Schaeffer

    2011-01-01

    The first poster session by students working on the LHC experiments, organised by the LPCC, was a great success. Showcasing the talents of over a hundred young physicists from all over the world, it was an opportunity for everyone at CERN to check out the wide range of research work being done by the new generation of physicists at CERN.   At 5.30 p.m. on Wednesday 23 March, the first poster session by CERN students took place in Restaurant No.1, where no fewer than 87 posters went on public display. The students were split into 8 groups according to their research field* and all were on hand to answer the questions of an inquisitive audience. TH Department's Michelangelo Mangano, who is head of the LHC Physics Centre at CERN (LPCC) and is responsible for the initiative, confirms that nothing was left to chance, even the choice of date: "We wanted to make the most of the general enthusiasm around the winter conferences and the meeting of the LHC Experiments Committee to present the stud...

  1. Citizenship displayed by disabled people

    Directory of Open Access Journals (Sweden)

    Eliana Prado Carlino

    2010-12-01

    Full Text Available By investigating the processes by which successful teachers become activate citizens and by listening to the diversity and richness of their life and formation stories, this work became possible. Its aim is to display some of the utterances of two Down Syndrome individuals and their active-citizenship activities. Their stories were told in the reports of two teachers when describing their personal and professional history, and were considered to be an integral part of it. Thus, some of the utterances and perceptions with which these two individuals elaborate their references, their worldview and their active-citizenship activity are evidenced in this paper. This article is based on the language conceptions of Vygotsky and Bakhtin who defend the idea that the group and the social mentality are ingrain in the individual. Hence, the history of one person reveals that of many others, since there is a deep link between the individual and the social in the formation of a subjective worldview. As a result, it can be easily seen that the utterances expressed by the participants in this research cannot be considered strictly individual because enunciation is social in nature. Despite the fact that the utterances are those of individuals, they manifest a collective reality. This demonstrates the real advantages and possibilities that deficient people get from their participation and intervention in society.

  2. Working session 2: Tubing inspection

    Energy Technology Data Exchange (ETDEWEB)

    Guerra, J. [Tecnatom, S.A. San Sebastian de los Reyes, Madrid (Spain); Tapping, R.L. [AECL, Chalk River, Ontario (Canada)

    1997-02-01

    This session was attended by delegates from 10 countries, and four papers were presented. A wide range of issues was tabled for discussion. Realizing that there was limited time available for more detailed discussion, three topics were chosen for the more detailed discussion: circumferential cracking, performance demonstration (to focus on POD and sizing), and limits of methods. Two other subsessions were organized: one dealt with some challenges related to the robustness of current inspection methods, especially with respect to leaving cracked tubes in service, and the other with developing a chart of current NDE technology with recommendations for future development. These three areas are summarized in turn, along with conclusions and/or recommendations. During the discussions there were four presentations. There were two (Canada, Japan) on eddy current probe developments, both of which addressed multiarray probes that would detect a range of flaws, one (Spain) on circumferential crack detection, and one (JRC, Petten) on the recent PISC III results.

  3. Paramecium swimming in capillary tube

    CERN Document Server

    Jana, Saikat; Jung, Sunghwan

    2010-01-01

    Swimming organisms in their natural habitat navigate through a wide array of geometries and chemical environments. Interaction with the boundaries is ubiquitous and can significantly modify the swimming characteristics of the organism as observed under ideal conditions. We study the dynamics of ciliary locomotion in Paramecium multimicronucleatum and observe the effect of the solid boundaries on the velocities in the near field of the organism. Experimental observations show that Paramecium executes helical trajectories that slowly transition to straight line motion as the diameter of the capillary tubes decrease. Theoretically this system is modeled as an undulating cylinder with pressure gradient and compared with experiments; showing that such considerations are necessary for modeling finite sized organisms in the restrictive geometries.

  4. Failure analysis of retired steam generator tubings

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hong Pyo; Kim, J. S.; Hwang, S. S. and others

    2005-04-15

    Degradation of steam generator leads to forced outage and extension of outage, which causes increase in repair cost, cost of purchasing replacement power and radiation exposure of workers. Steam generator tube rupture incident occurred in Uljin 4 in 2002, which made public sensitive to nuclear power plant. To keep nuclear energy as a main energy source, integrity of steam generator should be demonstrated. Quantitative relationship between ECT(eddy current test) signal and crack size is needed in assesment of integrity of steam generator in pressurized water reactor. However, it is not fully established for application in industry. Retired steam generator of Kori 1 has many kinds of crack such as circumferential and axial primary water stress corrosion crack and outer diameter stress corrosion crack(ODSCC). So, it can be used in qualifying and improving ECT technology and in condition monitoring assesment for crack detected in ISI(in service inspection). In addition, examination of pulled tube of Kori 1 retired steam generator will give information about effectiveness of non welded sleeving technology which was employed to repair defect tubes and remedial action which was applied to mitigate ODSCC. In this project, hardware such as semi hot lab. for pulled tube examination and modification transportation cask for pulled tube and software such as procedure of transportation of radioactive steam generator tube and non-destructive and destructive examination of pulled tube were established. Non-destructive and destructive examination of pulled tubes from Kori 1 retired steam generator were performed in semi hot lab. Remedial actions applied to Kori 1 retired steam generator, PWSCC trend and bulk water chemistry and crevice chemistry in Kori 1 were evaluated. Electrochemical decontamination technology for pulled tube was developed to reduce radiation exposure and enhance effectiveness of pulled tube examination. Multiparameter algorithm developed at ANL, USA was

  5. Observation of "YouTube" Language Learning Videos ("YouTube" LLVS)

    Science.gov (United States)

    Alhamami, Munassir

    2013-01-01

    This paper navigates into the "YouTube" website as one of the most usable online tools to learn languages these days. The paper focuses on two issues in creating "YouTube" language learning videos: pedagogy and technology. After observing the existing "YouTube" LLVs, the study presents a novel rubric that is directed…

  6. 49 CFR 230.61 - Arch tubes, water bar tubes, circulators and thermic siphons.

    Science.gov (United States)

    2010-10-01

    ... (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Boilers and Appurtenances Washing Boilers § 230.61 Arch tubes, water bar tubes, circulators and thermic siphons. (a) Frequency of cleaning. Each time the boiler is washed, arch tubes and...

  7. The effect of display movement angle, indicator type and display location on control/display stereotype strength.

    Science.gov (United States)

    Hoffmann, Errol R; Chan, Alan H S

    2017-08-01

    Much research on stereotype strength relating display and control movements for displays moving in the vertical or horizontal directions has been reported. Here we report effects of display movement angle, where the display moves at angles (relative to the vertical) of between 0° and 180°. The experiment used six different controls, four display locations relative to the operator and three types of indicator. Indicator types were included because of the strong effects of the 'scale-side principle' that are variable with display angle. A directional indicator had higher stereotype strength than a neutral indicator, and showed an apparent reversal in control/display stereotype direction beyond an angle of 90°. However, with a neutral indicator this control reversal was not present. Practitioner Summary: The effects of display moving at angles other than the four cardinal directions, types of control, location of display and types of indicator are investigated. Indicator types (directional and neutral) have an effect on stereotype strength and may cause an apparent control reversal with change of display movement angle.

  8. Conceptual Design of Industrial Process Displays

    DEFF Research Database (Denmark)

    Pedersen, C.R.; Lind, Morten

    1999-01-01

    Today, process displays used in industry are often designed on the basis of piping and instrumentation diagrams without any method of ensuring that the needs of the operators are fulfilled. Therefore, a method for a systematic approach to the design of process displays is needed. This paper...... design method that matches the industrial practice of modular plant design and satisfies the needs of reusability of display design solutions. The main considerations in display design in the industry are to specify the operator's activities in detail, to extract the information the operators need from...... the plant design specification and documentation, and finally to present this information. The form of the display is selected from existing standardized display elements such as trend curves, mimic diagrams, ecological interfaces, etc. Further knowledge is required to invent new display elements. That is...

  9. Comparison of LCD and CRT displays based on efficacy for digital mammography.

    Science.gov (United States)

    Saunders, Robert S; Samei, Ehsan; Baker, Jay; Delong, David; Soo, Mary Scott; Walsh, Ruth; Pisano, Etta; Kuzmiak, Cherie M; Pavic, Dag

    2006-11-01

    To compare two display technologies, cathode ray tube (CRT) and liquid crystal display (LCD), in terms of diagnostic accuracy for several common clinical tasks in digital mammography. Simulated masses and microcalcifications were inserted into normal digital mammograms to produce an image set of 400 images. Images were viewed on one CRT and one LCD medical-quality display device by five experienced breast-imaging radiologists who rated the images using a categorical rating paradigm. The observer data were analyzed to determine overall classification accuracy, overall lesion detection accuracy, and accuracy for four specific diagnostic tasks: detection of benign masses, malignant masses, and microcalcifications, and discrimination of benign and malignant masses. Radiologists had similar overall classification accuracy (LCD: 0.83 +/- 0.01, CRT: 0.82 +/- 0.01) and lesion detection accuracy (LCD: 0.87 +/- 0.01, CRT: 0.85 +/- 0.01) on both displays. The difference in accuracy between LCD and CRT for the detection of benign masses, malignant masses, and microcalcifications, and discrimination of benign and malignant masses was -0.019 +/- 0.009, 0.020 +/- 0.008, 0.012 +/- 0.013, and 0.0094 +/- 0.011, respectively. Overall, the two displays did not exhibit any statistically significant difference (P > .05). This study explored the suitability of two different soft-copy displays for the viewing of mammographic images. It found that LCD and CRT displays offer similar clinical utility for mammographic tasks.

  10. Broadcast yourself on YouTube - really?

    NARCIS (Netherlands)

    Kruitbosch, G.; Nack, F.

    2008-01-01

    One essential reason for people to publish on the web is to express themselves freely. YouTube facilitates this self-expression by allowing users to upload video content they generated. This paper investigates to what extent the videos on YouTube are self-generated content, instead of amalgamated

  11. Short Communication Tube-forming polychaetes enhance ...

    African Journals Online (AJOL)

    We collected invertebrate samples from an intertidal flat with low onuphid tube density (2.7 m–2) in Mozambique and document that more organisms (70 times higher mollusc abundances) and more species (15 times more mollusc species) were found associated with solitary tubes of an onuphid polychaete compared with ...

  12. Selecting silicone tubing for device applications.

    Science.gov (United States)

    Jahn, D

    2005-10-01

    A number of factors are involved in selecting the most suitable silicone tubing for a given purpose. These include physical chemistry, performance properties, a supplier's quality system and regulatory compliance. This article provides a guide for device developers when selecting silicone tubing for their applications.

  13. Non-uniform tube representation of proteins

    DEFF Research Database (Denmark)

    Hansen, Mikael Sonne

    might not correctly capture volume exclusion - of crucial importance when trying to understand a proteins $3$d-structure. We propose a new reduced model treating the protein as a non-uniform tube with a radius reflecting the positions of atoms. The tube representation is well suited considering X...

  14. Non-Uniform Tube Representation of Proteins

    DEFF Research Database (Denmark)

    Hansen, Mikael Sonne

    might not correctly capture volume exclusion - of crucial importance when trying to understand a protein's 3d-structure. We propose a new reduced model treating the protein as a non-uniform tube with a radius reflecting the positions of atoms. The tube representation is well suited considering X...

  15. Places to Go: YouTube

    Science.gov (United States)

    Downes, Stephen

    2008-01-01

    Founded in 2005 by three former PayPal employees, YouTube has revolutionized the Internet, marking a change from the static Internet to the dynamic Internet. In this edition of Places to Go, Stephen Downes discusses how the rise of a ubiquitous media format--Flash video--has made YouTube's success possible and argues that Flash video has important…

  16. Photomultiplier tubes for Low Level Cerenkov Detectors

    Energy Technology Data Exchange (ETDEWEB)

    Strindehag, O.

    1965-03-15

    Tube backgrounds of several 2-inch photomultiplier types having S11, 'S' , S13 and S20 cathodes are compared by measuring signal and background pulse height distributions at pulse heights corresponding to a few photo-electrons. The reference signal is generated by means of a {beta}-source and a plexiglass radiator. It is found that comparatively good results are obtained with selected tubes of the EMI types 6097B and 9514B having equivalent dark current dc values down to 10{sup -12} input lumens. Special interest is devoted to the correlation between the measured tube backgrounds and the dark current dc values of the tubes, as a good correlation between these parameters simplifies the selection of photomultiplier tubes. The equivalent dark currents of the tested tubes extend over the range 10{sup -12} to 10{sup -9} input lumens. Although the investigation deals with photomultiplier tubes intended for use in low level Cerenkov detectors it is believed that the results could be valuable in other fields where photomultiplier tubes are utilized for the detection of weak light pulses.

  17. Confined Tube Crimp Using Portable Hand Tools

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, Joseph James [Los Alamos National Laboratory; Pereyra, R. A. [LANL Retired; Archuleta, Jeffrey Christopher [Los Alamos National Laboratory; Martinez, Isaac P. [Los Alamos National Laboratory; Nelson, A. M. [MST-16 Summer Student (2007); Allen, Ronald Scott [Los Alamos National Laboratory; Page, R. L. [LANL Retired; Freer, Jerry Eugene [Los Alamos National Laboratory; Dozhier, Nathan Gus [Los Alamos National Laboratory

    2016-04-04

    The Lawrence Radiation Laboratory developed handheld tools that crimp a 1/16 inch OD tube, forming a leak tight seal1 (see Figure 1). The leak tight seal forms by confining the 1/16 inch OD tubing inside a die while applying crimp pressure. Under confined pressure, the tube walls weld at the crimp. The purpose of this study was to determine conditions for fabricating a leak tight tube weld. The equipment was used on a trial-and-error basis, changing the conditions after each attempt until successful welds were fabricated. To better confine the tube, the die faces were polished. Polishing removed a few thousandths of an inch from the die face, resulting in a tighter grip on the tubing wall. Using detergent in an ultrasonic bath, the tubing was cleaned. Also, the time under crimp pressure was increased to 30 seconds. With these modifications, acceptable cold welds were fabricated. After setting the conditions for an acceptable cold weld, the tube was TIG welded across the crimped face.

  18. Sampling Artifacts from Conductive Silicone Tubing

    Energy Technology Data Exchange (ETDEWEB)

    Timko, Michael T.; Yu, Zhenhong; Kroll, Jesse; Jayne, John T.; Worsnop, Douglas R.; Miake-Lye, Richard C.; Onasch, Timothy B.; Liscinsky, David; Kirchstetter, Thomas W.; Destaillats, Hugo; Holder, Amara L.; Smith, Jared D.; Wilson, Kevin R.

    2009-05-15

    We report evidence that carbon impregnated conductive silicone tubing used in aerosol sampling systems can introduce two types of experimental artifacts: 1) silicon tubing dynamically absorbs carbon dioxide gas, requiring greater than 5 minutes to reach equilibrium and 2) silicone tubing emits organic contaminants containing siloxane that adsorb onto particles traveling through it and onto downstream quartz fiber filters. The consequence can be substantial for engine exhaust measurements as both artifacts directly impact calculations of particulate mass-based emission indices. The emission of contaminants from the silicone tubing can result in overestimation of organic particle mass concentrations based on real-time aerosol mass spectrometry and the off-line thermal analysis of quartz filters. The adsorption of siloxane contaminants can affect the surface properties of aerosol particles; we observed a marked reduction in the water-affinity of soot particles passed through conductive silicone tubing. These combined observations suggest that the silicone tubing artifacts may have wide consequence for the aerosol community and should, therefore, be used with caution. Gentle heating, physical and chemical properties of the particle carriers, exposure to solvents, and tubing age may influence siloxane uptake. The amount of contamination is expected to increase as the tubing surface area increases and as the particle surface area increases. The effect is observed at ambient temperature and enhanced by mild heating (<100 oC). Further evaluation is warranted.

  19. Isolated Fallopian Tube Torsion in Adolescents

    Directory of Open Access Journals (Sweden)

    S. Rajaram

    2013-01-01

    Full Text Available Background. Fallopian tube torsion is a rare cause of acute abdomen, occurring commonly in females of reproductive age. It lacks pathognomonic symptoms, signs, or imaging features, thus causing delay in surgical intervention. Case. We report two cases of isolated fallopian tube torsion in adolescent girls. In the first case a 19-year-old patient presented with acute pain in the left iliac region associated with episodes of vomiting for one day and mild tenderness on examination. Laparoscopy revealed left sided twisted fallopian tube associated with hemorrhagic cyst of ovary. The tube was untwisted and salvaged. In another case an 18-year-old virgin girl presented with similar complaints since one week, associated with mild tenderness in the lower abdomen and tender cystic mass on per rectal examination. On laparoscopy right twisted fallopian tube associated with a paratubal cyst was found. Salpingectomy was done as the tube was gangrenous. Conclusion. Fallopian tube torsion, though rare, should be considered in women of reproductive age with unilateral pelvic pain. Early diagnostic laparoscopy is important for an accurate diagnosis and could salvage the tube.

  20. A Slot Machine, A Broken Test Tube

    Indian Academy of Sciences (India)

    IAS Admin

    BOOK │ REVIEW. A Slot Machine, A Broken. Test Tube. Vinita Shivakumar and. Dipshikha Chakravortty. A Slot Machine, A Broken Test. Tube – An Autobiography. Salvador Edward Luria. Harper Collins Publishers Inc.,. USA. 1984. 1st edn. 228 pp. (Original from the University of. Michigan). Price: Rs 60/-. Salvador Edward ...

  1. Teaching Shakespeare with YouTube

    Science.gov (United States)

    Desmet, Christy

    2009-01-01

    YouTube, the video sharing website that allows viewers to upload video content ranging from cute dog tricks to rare rock videos, also supports a lively community devoted to the performance of Shakespeare and Shakespearean adaptations. YouTube is also a popular site for student producers of Shakespeare performances, parodies, and other artistic…

  2. Geotextile Tube Structures Guidelines for Contract Specifications

    Science.gov (United States)

    2006-09-01

    Nonwoven fabrics: Diaphragm Bursting Strength Tester Method ASTM D 3884 (1992) Abrasion Resistance of Textile Fabrics (Rotary Platform, Double-Head... filter cloth, excavation of borrow material, transportation of borrow material, filling of the tubes, coating of the completed tubes, disposal of waste

  3. Local Thickening of Stainless Tube Considering Dimension Variation of the Cold Roll Formed Tube Billet

    Science.gov (United States)

    Sheu, Jinn-Jong; Yu, Cheng-Hsien

    2011-01-01

    A stud end consists of tube body and a flange in order to connect two tubes to form a long straight or angled pipe line. The flange is thicker than the tube body to strengthen the pipe connection. A thicker round hollow disk is usually welded to a straight tube to get the flange of the tube end and then machined to the specified dimension of the two-piece type stud end. A one-piece type stud end of tube proposed here is produced via the local thickening of tube end, flaring, and flange forging processes. The roundness of raw tube is not promised in the cold roll forming (CRF) process, which causes the inaccuracy of dimensions, wrinkling, and folding defects during the local thickening process of tube end. In this paper, a preform process was proposed to correct the dimension of the tube to be thickened. The CRF tube billets were measured and preformed to the required dimensions before thickening. The proposed preforming process was able to resize and control the dimensions and roundness of the tube billet to prevent irregular movement of billet. A three-staged punch profile was designed to prevent the folding defect during the thickening process. Experiments of resizing and thickening were carried out to verify the simulation results and the proposed punch profile design. The CAE simulations demonstrated the defects of folding are very sensitive to the dimension variation of tube billet. The experimental results of thickening process were in good agreement with the simulation predictions using the perfect (with preforming process) and the imperfect (original CRF) tube billets. The proposed pre-forming process and the punch profile designs were able to minimize the surface defects of tube local thickening.

  4. Building lab-scale x-ray tube based irradiators

    Science.gov (United States)

    The construction of economical x-ray tube based irradiators in a variety of configurations is described using 1000 Watt x-ray tubes. Single tube, double tube, and four tube designs are described, as well as various cabinet construction techniques. Relatively high dose rates were achieved for small s...

  5. Tubing-for-casing cuts tubular requirements

    Energy Technology Data Exchange (ETDEWEB)

    Kelley, C.W. Jr.

    1974-04-01

    The tight supply of tubular goods has caused many operators to turn to tubingless completions in field wells devoid of critical downhole problems. It is possible to save up to 50% on tubular steel requirements by this technique. Other than the surface casing, the basic idea employs only one string of pipe of tubing dimensions. Such a completion is illustrated. Tubingless completions generally refer to the use of 2-7/8 in. tubing which is run and cemented as the production casing of a well. In this light, the term tubingless is a misnomer and perhaps tubing-for-casing more aptly described the idea. Tubing-for-casing completions should be considered usually for gas wells where future anticipated remedial work is minimal. However, these completions can be squeezed and normal remedial work can be accomplished with a variety of available tools. Some of the problems that should be investigated when considering a tubing-for-casing are listed and described.

  6. The Mashups of YouTube

    DEFF Research Database (Denmark)

    Simonsen, Thomas Mosebo

    2013-01-01

    This article focuses on YouTube mashups and how we can understand them as a specific subgenre on YouTube. The Mashups are analysed as audiovisual recontextualizations that are given new meaning, e.g., via collaborative social communities or for individual promotional purposes. This is elaborated......, but rather in its social and communicative abilities within the YouTube community. This leads to the article’s overall argument that the main characteristic of the YouTube Mashup can be explained in terms of connectivity. It is argued that Mashups reveal a double articulation of connectivity; one...... that involves the social mechanisms of the Mashups, and another mode, which concerns the explicit embedding of structural connectivity that accentuates the medium-specific infrastructure of YouTube. This double articulation of connectivity is furthermore elaborated on by including Grusin and Bolter’s concept...

  7. Torsional Kinematic Model for Concentric Tube Robots.

    Science.gov (United States)

    Dupont, Pierre E; Lock, Jesse; Butler, Evan

    2009-05-12

    A recent approach to steerable needle design is based on combining pre-curved tubes concentrically. By rotating and extending the tubes with respect to each other, the position and orientation of the needle tip, as well as the shape of the inserted length, can be controlled. Prior models neglected torsional twisting in the curved portions of the tubes. This paper presents a mechanics model that includes torsion, applies to any number of tubes and allows curvature and stiffness to vary with arc length. While the general model is comprised of differential equations, an analytic solution is given for two tubes of constant curvature. This solution enables analytic prediction of "snap through" instability based on a single dimensionless parameter. Simulation and experiments are used to illustrate the results.

  8. Can nasal decongestants improve eustachian tube function?

    Science.gov (United States)

    Ovari, Attila; Buhr, Anne; Warkentin, Mareike; Kundt, Günther; Ehrt, Karsten; Pau, Hans-Wilhelm

    2015-01-01

    To evaluate the effect of nasal decongestants on eustachian tube (ET) opening. A prospective nonrandomized study. A tertiary referral center. Twenty-four patients (44 ears) with intact eardrums, 39 patients (43 ears) having a noninfected eardrum defect, and six patients with an upper airway infection. Nasal or intratympanal (in perforated ears) application of a nasal decongestant (xylometazoline 0.1%). Change of tube opening quality (yes or no; better or worse) measuring tube opening parameters (pressure, latency) using the Estève method and pressure equalization tests (swallowing at negative and positive external ear canal pressures). In most cases, nasal decongestion or intratympanal use of decongestants have no effect on ET opening. Improvement in tube opening is rather an exception and, in a minority of patients, a reduced ET function was evident. Our acute studies revealed no improvement in eustachian ventilatory tube function with the administration of nasal decongestants.

  9. Explosion interaction with water in a tube

    Science.gov (United States)

    Homae, T.; Sugiyama, Y.; Wakabayashi, K.; Matsumura, T.; Nakayama, Y.

    2017-02-01

    As proposed and legislated in Japan, subsurface magazines have an explosive storage chamber, a horizontal passageway, and a vertical shaft for a vent. The authors found that a small amount of water on the floor of the storage chamber mitigated blast pressure remarkably. The mitigation mechanism has been examined more closely. To examine the effect of water, the present study assesses explosions in a transparent, square cross section, and a straight tube. A high-speed camera used to observe the tube interior. Blast pressure in and around the tube was also measured. Images obtained using the high-speed camera revealed that water inside the tube did not move after the explosion. Differences between cases of tubes without water and with water were unclear. Along with blast pressure measurements, these study results suggest that blast pressure mitigation by water occurs because of interaction between the explosion and the water near the explosion point.

  10. A novel method for the preparation of electrophoretic display microcapsules

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xiao-Meng; He, Jing; Liu, Sheng-Yun [State Key Laboratory of Organic-Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China); Chen, Jian-Feng [State Key Laboratory of Organic-Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China); Research Center of the Ministry of Education for High Gravity Engineering and Technology, Beijing University of Chemical Technology, Beijing 100029 (China); Le, Yuan, E-mail: leyuan@mail.buct.edu.cn [State Key Laboratory of Organic-Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China)

    2014-07-01

    Highlights: • The electrophoretic display microcapsules were prepared by coaxial jet method aided by gas spray. • The positions of inner tube, liquid and gas flow rate of the process were investigated. • The size and shell thickness of the prepared microcapsules were controllable. • The prepared microcapsules had high coating ratio and exhibit reversible response to DC field. - Abstract: The narrow distributed electrophoretic display microcapsules containing electrophoretic ink were prepared using coaxial jet method aided by gas spray. Experimental results showed the size and shell thickness of the microcapsules could be controlled by adjusting flow rates of core and shell fluids as well as gas. The as-prepared white and red microcapsules, with average size of 100 and 200 μm respectively, had high coating ratio (above 90%) and exhibited reversible response to DC electric field. Compared with the approach of other microencapsulation methods, the new technique not only has a simple procedure but also provides a more effective way of size control. This novel method is expected to prepare microcapsules with potential application in the fields of electronic paper and other material science.

  11. Miniaturized LEDs for flat-panel displays

    Science.gov (United States)

    Radauscher, Erich J.; Meitl, Matthew; Prevatte, Carl; Bonafede, Salvatore; Rotzoll, Robert; Gomez, David; Moore, Tanya; Raymond, Brook; Cok, Ronald; Fecioru, Alin; Trindade, António Jose; Fisher, Brent; Goodwin, Scott; Hines, Paul; Melnik, George; Barnhill, Sam; Bower, Christopher A.

    2017-02-01

    Inorganic light emitting diodes (LEDs) serve as bright pixel-level emitters in displays, from indoor/outdoor video walls with pixel sizes ranging from one to thirty millimeters to micro displays with more than one thousand pixels per inch. Pixel sizes that fall between those ranges, roughly 50 to 500 microns, are some of the most commercially significant ones, including flat panel displays used in smart phones, tablets, and televisions. Flat panel displays that use inorganic LEDs as pixel level emitters (μILED displays) can offer levels of brightness, transparency, and functionality that are difficult to achieve with other flat panel technologies. Cost-effective production of μILED displays requires techniques for precisely arranging sparse arrays of extremely miniaturized devices on a panel substrate, such as transfer printing with an elastomer stamp. Here we present lab-scale demonstrations of transfer printed μILED displays and the processes used to make them. Demonstrations include passive matrix μILED displays that use conventional off-the shelf drive ASICs and active matrix μILED displays that use miniaturized pixel-level control circuits from CMOS wafers. We present a discussion of key considerations in the design and fabrication of highly miniaturized emitters for μILED displays.

  12. [Development of platform technology using molecular display].

    Science.gov (United States)

    Shibasaki, Seiji

    2009-11-01

    Techniques for immobilizing proteins on surface of virus or microorganisms, namely molecular display technologies, have played important roles in helping the elucidation of protein-protein interactions in cells and to develop research on drug discovery. Phage display system is well-established and sophisticated; consequently, bioactive low-molecular-weight ligands and proteins significant in pharmaceutical industry have been found. In addition to the development of novel functional proteins by phage display using results from experiments in genomics and proteomics, ribosome display or yeast display systems have been developed as complementary methods. We can select the appropriate method on the basis of the objective. Molecular display using yeast has advantages in production of desired proteins from combinatorial library by flow cytometry. Firstly, principle, development procedure, and latest research in this field are introduced. Thereafter, results of molecular display using yeast for antibodies and their related proteins are presented. Furthermore, display of receptor coupled with intracellular signal transduction -a novel type of molecular display on yeast cell surface- has been created in recent years. The role and potential of molecular display technologies employing yeast cells in drug discovery are discussed.

  13. Eddy current inspection of power plant heat-exchanger tubing in the USA

    Energy Technology Data Exchange (ETDEWEB)

    Fishkin, P.; Nash, J. [MQS Inspection, Inc., Chicago, IL (United States)

    1995-02-01

    The latest experience in the eddy current inspection of heat-exchanger tubing by means of ID probes is reported and generalized. The authors demonstrate the feasibility of using modern, general-purpose, digital eddy current flaw detectors equipped with microprocessors, displays, the capability for recording inspection results on paper or magnetic media, sound and visual alarms. The NDE personnel qualification and certification requirements are described.

  14. “How to Pronounce Meme.” Three YouTube Channels

    Directory of Open Access Journals (Sweden)

    Sandy Baldwin

    2017-03-01

    Full Text Available Internet anomalies produce data and images beyond any authorship or source. They seem to compute and display the depths and potentials of the net “as such.” Explanations and theories surround and attempt to account for anomalies, from ARGs to NSA recruiting tools. Examining three such anomalous YouTube channels, this essay does not propose a solution but rather maintains the anomalous as the constituent aesthetic and community of the net.

  15. A multiprimary display model combined with a spatio-temporal behavioral display model for display characterization by simulation

    Science.gov (United States)

    Dolar, Carsten; Lebowsky, Fritz

    2009-01-01

    With the development of fast liquid crystal cells and with advent of backlight units with separate red, green and blue light emitting diodes also first commercial color sequential display emerge. Another technique in commercial application proposes implementing more than three subpixels and thus enhanced color gamut by using multiple color primaries. Also the combination of both color mixture techniques is possible. It is thus desirable to have a simulation workbench at hand that is flexible enough to adapt to the various possibilities of subpixel design and color sequences in display design to evaluate the displayed image in advance. The combination of a multiprimary display model, which can emulate a multiprimary display on a standard RGB LC display, and a spatio-temporal model, that describes LC pixel behavior to arbitrary input signals over time, provides means for simulating the perceived image of a color-sequential display behavior. This article describes the combined model and gives also simulation results that compare advanced displays to conventional vertical stripe RGB LC display.

  16. Microfluidics for electronic paper-like displays.

    Science.gov (United States)

    Shui, Lingling; Hayes, Robert A; Jin, Mingliang; Zhang, Xiao; Bai, Pengfei; van den Berg, Albert; Zhou, Guofu

    2014-07-21

    Displays are ubiquitous in modern life, and there is a growing need to develop active, full color, video-rate reflective displays that perform well in high-light conditions. The core of display technology is to generate or manipulate light in the visible wavelength. Colored fluids or fluids with particles can be used to tune the light intensity (greyscale) or wavelength (colors) of reflective displays by different actuation methods. Microfluidic technology plays an increasing role in fluidic manipulation in microscale devices used in display areas. In this article, we will review microfluidic technologies based on different actuation methods used for display applications: pressure-driven flow, electrophoresis, electroosmosis, electrowetting, magnetic-driven flow, and cell-actuation principles.

  17. Three-dimensional Imaging, Visualization, and Display

    CERN Document Server

    Javidi, Bahram; Son, Jung-Young

    2009-01-01

    Three-Dimensional Imaging, Visualization, and Display describes recent developments, as well as the prospects and challenges facing 3D imaging, visualization, and display systems and devices. With the rapid advances in electronics, hardware, and software, 3D imaging techniques can now be implemented with commercially available components and can be used for many applications. This volume discusses the state-of-the-art in 3D display and visualization technologies, including binocular, multi-view, holographic, and image reproduction and capture techniques. It also covers 3D optical systems, 3D display instruments, 3D imaging applications, and details several attractive methods for producing 3D moving pictures. This book integrates the background material with new advances and applications in the field, and the available online supplement will include full color videos of 3D display systems. Three-Dimensional Imaging, Visualization, and Display is suitable for electrical engineers, computer scientists, optical e...

  18. Evaluating Ambient Displays in the Wild

    DEFF Research Database (Denmark)

    Messeter, Jörn; Molenaar, Daryn

    A prominent issue for evaluating ambient displays has been the conflict between the relative intrusiveness of evaluation methods and the intention to keep the display at the periphery of the user’s attention. There is a general lack of research discussing the difficulties of evaluating ambient...... displays in the wild, and in particular social aspects of use has received little attention. This paper presents a case study of an ambient light display designed for a public setting. Based on results from a non-intrusive in situ evaluation, we argue that viewing ambient displays as features of a broader...... social setting may aid our understanding of issues regarding the evaluation of ambient displays in the wild....

  19. Legibility Implications of Embellished Display Typefaces

    DEFF Research Database (Denmark)

    Beier, Sofie; Sand, Katrine; Starrfelt, Randi

    2017-01-01

    By subjecting participants to brief exposure of single letters in the peripheral visual field, we investigated 1) hemispheric differences in reading of embellished display typefaces, and 2) the legibility difference between different kinds of embellished display typefaces. The test typefaces are ...... affected by swashed features than by a reversed letter stroke, or by a drop shadow. When choosing between different styles of embellished display typefaces, it is therefore recommended to choose typefaces where the letter skeleton is not too complicated to decode....

  20. Optimizing direct response in Internet display advertising

    OpenAIRE

    Aksakallı, Vural

    2013-01-01

    Internet display advertising has grown into a multi-billion dollar a year global industry and direct response campaigns account for about three-quarters of all Internet display advertising. In such campaigns, advertisers reach out to a target audience via some form of a visual advertisement (hereinafter also called “ad”) to maximize short-term sales revenue. In this study, we formulate an advertiser’s revenue maximization problem in direct response Internet display advertisement campaigns as ...

  1. Online Display Advertising Causal Attribution and Evaluation

    OpenAIRE

    BARAJAS ZAMORA, JOEL

    2015-01-01

    The allocation of a given budget to online display advertising as a marketing channel has motivated the development of statistical methods to measure its effectiveness. Recent studies show that display advertising often triggers online users to search for more information on products. Eventually, many of these users convert at the advertiser’s website. A key challenge is to measure the effectiveness of display advertising when users are exposed to multiple unknown advertising channels.We deve...

  2. Legibility implictations of embellished display typefaces

    DEFF Research Database (Denmark)

    Beier, Sofie; Sand, Katrine; Starrfelt, Randi

    2017-01-01

    By subjecting participants to brief exposure of single letters in the peripheral visual field, we investigated 1) hemispheric differences in reading of embellished display typefaces, and 2) the legibility difference between different kinds of embellished display typefaces. The test typefaces...... affected by swashed features than by a reversed letter stroke, or by a drop shadow. When choosing between different styles of embellished display typefaces, it is therefore recommended to choose typefaces where the letter skeleton is not too complicated to decode....

  3. The consumer’s choice among television displays: A multinomial logit approach

    Directory of Open Access Journals (Sweden)

    Carlos Giovanni González Espitia

    2013-07-01

    Full Text Available The consumer’s choice over a bundle of products depends on observable and unobservable characteristics of goods and consumers. This choice is made in order to maximize utility subject to a budget constraint. At the same time, firms make product differentiation decisions to maximize profit. Quality is a form of differentiation. An example of this occurs in the TV market, where several displays are developed. Our objective is to determine the probability for a consumer of choosing a type of display from among five kinds: standard tube, LCD, plasma, projection and LED. Using a multinomial logit approach, we find that electronic appliances like DVDs and audio systems, as well as socioeconomic status, increase the probability of choosing a high-tech television display. Our empirical approximation contributes to further understanding rational consumer behavior through the theory of utility maximization and highlights the importance of studying market structure and analyzing changes in welfare and efficiency.

  4. Atmosphere in a Test Tube

    Science.gov (United States)

    Claudi, R.; Pace, E.; Ciaravella, A.; Micela, G.; Piccioni, G.; Billi, D.; Cestelli Guidi, M.; Coccola, L.; Erculiani, M. S.; Fedel, M.; Galletta, G.; Giro, E.; La Rocca, N.; Morosinotto, T.; Poletto, L.; Schierano, D.; Stefani, S.

    The ancestor philosophers' dream of thousand of new world is finally realised: more than 1800 extrasolar planets have been discovered in the neighborhood of our Sun. Most of them are very different from those we used to know in our Solar System. Others orbit the Habitable Zone (HZ) of their parent stars. Space missions, as JWST and the very recently proposed ARIEL, or ground based instruments, like SPHERE@VLT, GPI@GEMINI and EPICS@ELT, have been proposed and built to measure the atmospheric transmission, reflection and emission spectra over a wide wavelength range of these new worlds. In order to interpret the spectra coming out by this new instrumentation, it is important to know in detail the optical characteristics of gases in the typical physical conditions of the planetary atmospheres and how those characteristics could be affected by radiation driven photochemical and bio-chemical reaction. Insights in this direction can be achieved from laboratory studies of simulated planetary atmosphere of different pressure and temperature conditions under the effects of radiation sources, used as proxies of different bands of the stellar emission. ''Atmosphere in a Test Tube'' is a collaboration among several Italian astronomical, biological and engineering institutes in order to share their experiencece in performing laboratory experiments on several items concerning extrasolar planet atmospheres.

  5. Tube Formation in Nanoscale Materials

    Directory of Open Access Journals (Sweden)

    Yan Chenglin

    2008-01-01

    Full Text Available Abstract The formation of tubular nanostructures normally requires layered, anisotropic, or pseudo-layered crystal structures, while inorganic compounds typically do not possess such structures, inorganic nanotubes thus have been a hot topic in the past decade. In this article, we review recent research activities on nanotubes fabrication and focus on three novel synthetic strategies for generating nanotubes from inorganic materials that do not have a layered structure. Specifically, thermal oxidation method based on gas–solid reaction to porous CuO nanotubes has been successfully established, semiconductor ZnS and Nb2O5nanotubes have been prepared by employing sacrificial template strategy based on liquid–solid reaction, and an in situ template method has been developed for the preparation of ZnO taper tubes through a chemical etching reaction. We have described the nanotube formation processes and illustrated the detailed key factors during their growth. The proposed mechanisms are presented for nanotube fabrication and the important pioneering studies are discussed on the rational design and fabrication of functional materials with tubular structures. It is the intention of this contribution to provide a brief account of these research activities.

  6. Steam generator tubing NDE performance

    Energy Technology Data Exchange (ETDEWEB)

    Henry, G. [Electric Power Research Institute, Charlotte, NC (United States); Welty, C.S. Jr. [Electric Power Research Institute, Palo Alto, CA (United States)

    1997-02-01

    Steam generator (SG) non-destructive examination (NDE) is a fundamental element in the broader SG in-service inspection (ISI) process, a cornerstone in the management of PWR steam generators. Based on objective performance measures (tube leak forced outages and SG-related capacity factor loss), ISI performance has shown a continually improving trend over the years. Performance of the NDE element is a function of the fundamental capability of the technique, and the ability of the analysis portion of the process in field implementation of the technique. The technology continues to improve in several areas, e.g. system sensitivity, data collection rates, probe/coil design, and data analysis software. With these improvements comes the attendant requirement for qualification of the technique on the damage form(s) to which it will be applied, and for training and qualification of the data analysis element of the ISI process on the field implementation of the technique. The introduction of data transfer via fiber optic line allows for remote data acquisition and analysis, thus improving the efficiency of analysis for a limited pool of data analysts. This paper provides an overview of the current status of SG NDE, and identifies several important issues to be addressed.

  7. Closed circuit TV system monitors welding operations

    Science.gov (United States)

    Gilman, M.

    1967-01-01

    TV camera system that has a special vidicon tube with a gradient density filter is used in remote monitoring of TIG welding of stainless steel. The welding operations involve complex assembly welding tools and skates in areas of limited accessibility.

  8. Resonant oscillations in open axisymmetric tubes

    Science.gov (United States)

    Amundsen, D. E.; Mortell, M. P.; Seymour, B. R.

    2017-12-01

    We study the behaviour of the isentropic flow of a gas in both a straight tube of constant cross section and a cone, open at one end and forced at or near resonance at the other. A continuous transition between these configurations is provided through the introduction of a geometric parameter k associated with the opening angle of the cone where the tube corresponds to k=0. The primary objective is to find long-time resonant and near-resonant approximate solutions for the open tube, i.e. k→ 0. Detailed analysis for both the tube and cone in the limit of small forcing (O(ɛ 3)) is carried out, where ɛ 3 is the Mach number of the forcing function and the resulting flow has Mach number O(ɛ ). The resulting approximate solutions are compared with full numerical simulations. Interesting distinctions between the cone and the tube emerge. Depending on the damping and detuning, the responses for the tube are continuous and of O(ɛ ). In the case of the cone, the resonant response involves an amplification of the fundamental resonant mode, usually called the dominant first-mode approximation. However, higher modes must be included for the tube to account for the nonlinear generation of higher-order resonances. Bridging these distinct solution behaviours is a transition layer of O(ɛ 2) in k. It is found that an appropriately truncated set of modes provides the requisite modal approximation, again comparing well to numerical simulations.

  9. Dynamic tube movement of Ahmed glaucoma valve.

    Science.gov (United States)

    Law, Simon K; Coleman, Anne L; Caprioli, Joseph

    2009-01-01

    To report the dynamic movement of the tube of the Ahmed glaucoma valve (AGV) in the anterior chamber with eye movement. Three patients (eyes) with dynamic movement of the tube of the AGV out of approximately 1500 AGV implantations over 10 years were identified. Demographic information, management, and patient outcomes were abstracted from the medical records. Possible mechanisms of the tube movement are discussed. In all 3 eyes, the fibrovascular capsule and the plate were noted to be stationary in the superior temporal fornix under the conjunctiva and did not move with movement of the eye. The length of the intraocular portion of the tube varied between 3 and 4 mm, depending on the position of the globe. All 3 eyes had undergone at least 1 intraocular procedure before AGV implantation and 2 of 3 eyes had at least 1 intraocular procedure after the AGV implantation. The dynamic movement of the tube was first observed from 0.5 to 7 years after the AGVs were implanted. It was not associated with any intraocular reaction, damage of intraocular tissue, or decrease of intraocular pressure control, and no additional surgical intervention has been required. Dynamic movement of the tube of AGV results from dissociation of the fibrovascular capsule and the plate in the fornix from the rotation of the globe. The length of the intraocular portion of the tube may vary widely with eye movement.

  10. Miniature acoustic guidance system for endotracheal tubes

    Science.gov (United States)

    Juan, Eduardo J.

    Ensuring that the distal end of an endotracheal tube is properly located within the trachea, and that the tube is not obstructed by mucous deposition, is a major clinical concern in patients that require mechanical ventilation. A novel acoustic system was developed to allow for the continuous monitoring of endotracheal tube position and patency. A miniature sound source and two sensing microphones are placed in-line between the ventilator hose and the proximal end of the endotracheal tube. Reflections of an acoustic pulse from the endotracheal tube lumen and the airways are digitally analyzed to estimate the location and degree of obstruction, as well as the position of the distal end of the tube in the airway. The system was evaluated through computer simulations, in vitro studies, and in a rabbit model. The system noninvasively estimated tube position in vivo to within roughly 4.5 mm, and differentiated between proper tracheal, and erroneous bronchial or esophageal intubation in all cases. In addition, the system estimated the area and location of lumen obstructions in vitro to within 14% and 3.5 mm, respectively. These findings indicate that this miniature technology could improve the quality of care provided to the ventilated adult and infant.

  11. Display of nuclear medicine imaging studies

    CERN Document Server

    Singh, B; Samuel, A M

    2002-01-01

    Nuclear medicine imaging studies involve evaluation of a large amount of image data. Digital signal processing techniques have introduced processing algorithms that increase the information content of the display. Nuclear medicine imaging studies require interactive selection of suitable form of display and pre-display processing. Static imaging study requires pre-display processing to detect focal defects. Point operations (histogram modification) along with zoom and capability to display more than one image in one screen is essential. This album mode of display is also applicable to dynamic, MUGA and SPECT data. Isometric display or 3-D graph of the image data is helpful in some cases e.g. point spread function, flood field data. Cine display is used on a sequence of images e.g. dynamic, MUGA and SPECT imaging studies -to assess the spatial movement of tracer with time. Following methods are used at the investigator's discretion for inspection of the 3-D object. 1) Display of orthogonal projections, 2) Disp...

  12. Microencapsulated Electrophoretic Films for Electronic Paper Displays

    Science.gov (United States)

    Amundson, Karl

    2003-03-01

    Despite the dominance of liquid crystal displays, they do not perform some functions very well. While backlit liquid crystal displays can offer excellent color performance, they wash out in bright lighting and suffer from high power consumption. Reflective liquid crystal displays have limited brightness, making these devices challenging to read for long periods of time. Flexible liquid crystal displays are difficult to manufacture and keep stable. All of these attributes (long battery lifetime, bright reflective appearance, compatibility with flexible substrates) are traits that would be found in an ideal electronic paper display - an updateable substitute for paper that could be employed in electronic books, newspapers, and other applications. I will discuss technologies that are being developed for electronic-paper-like displays, and especially on particle-based technologies. A microencapsulated electrophoretic display technology is being developed at the E Ink corporation. This display film offers offer high brightness and an ink-on-paper appearance, compatibility with flexible substrates, and image stability that can lead to very low power consumption. I will present some of the physical and chemical challenges associated with making display films with high performance.

  13. History Of Holographic Display In Japan

    Science.gov (United States)

    Iwata, Fujio

    1987-06-01

    The first exhibition of holographic display was held at Seibu Museum of Art in Tokyo in 1975 and played a role of opening of the holographic era in Japan. This exhibition and the next big exhibition of holography held at Isetan department store 3 years later in 1978 were really epoch-making facts on holographic display in Japan. Since these two exhibitions, holographic display in Japan has come to attract attention of a lot of people to the new display media, holography. At that time, mass production technology of holograms had not been fully developed yet, and the hologram was so expensive that they were found only at the big event. Some companies and universities still continued research and development to have holograms get into practical applications of display media. Few years later, people became interested in 3-D displays and sometimes many peoples took an interest in holographic display, mainly mass produced embossed type holograms applied to the field of publications, book and magazine, etc. 3-D display booms occurred in the year of Tsukuba Science Expo'85 in 1985 and embossed type hologram became much popular. History of holographic display of Japan in terms of technical development and practical use on laser reconstruction hologram, rainbow hologram, multiplex hologram and lippmann hologram will be introduced.

  14. Refreshable Braille displays using EAP actuators

    Science.gov (United States)

    Bar-Cohen, Yoseph

    2010-04-01

    Refreshable Braille can help visually impaired persons benefit from the growing advances in computer technology. The development of such displays in a full screen form is a great challenge due to the need to pack many actuators in small area without interferences. In recent years, various displays using actuators such as piezoelectric stacks have become available in commercial form but most of them are limited to one line Braille code. Researchers in the field of electroactive polymers (EAP) investigated methods of using these materials to form full screen displays. This manuscript reviews the state of the art of producing refreshable Braille displays using EAP-based actuators.

  15. Human Factors Military Lexicon: Auditory Displays

    National Research Council Canada - National Science Library

    Letowski, Tomasz

    2001-01-01

    .... In addition to definitions specific to auditory displays, speech communication, and audio technology, the lexicon includes several terms unique to military operational environments and human factors...

  16. PENGARUH DISPLAY PRODUK PADA KEPUTUSAN PEMBELIAN KONSUMEN

    Directory of Open Access Journals (Sweden)

    Ina Melati

    2012-11-01

    Full Text Available Most of ritel outlet recently using product display as a one of their best marketing strategy, the reason is quiet easy to be understood, since consumers are too easy to be teased by those kind of beautiful product display that is being displayed by the retail outlet. The good retail outlets are trying their best to design and make the very good product display, so they can attract more consumers and make them not thinking twice to visit their store and purchase lots of thing. Clearly seeing that an attractive product design is able to influence a consumer to make a buying decision. 

  17. Stroke: Ineffective tube securement reduces nutrition and drug treatment

    OpenAIRE

    Brazier, S.; Taylor, S.J.; Allan, K; R. Clemente; Toher, D.

    2017-01-01

    Stroke patients with dysphagia often depend on nutrition, hydration and medication via nasogastric (NG) feeding tubes. Securing tubes using tape was associated with repeated tube loss. We determined cause and effect by auditing tube placement methods, delays incurred, duration and costs. Of 202 NG tube placements in 75 patients, 67 placements occurred in 17 patients over a full course of enteral nutrition (EN) and 40 of these placements were tracked. Tubes were secured by tape in 100%, mitten...

  18. Development of inconel alloys precision tube

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Young-Hee; Lee, D. H.; Shin, Y. S.; Park, J. H. [Changwon Speciality Steel Co., Ltd., Changwon (Korea); Kim, J. S.; Kim, H. P; Lim, Y. S.; Hwang, S. S.; Jung, M. K.; Woo, Y. M.; Han, C. H. [Korea Atomic Energy Research Institute, Taejeon (Korea)

    1998-04-01

    The purpose of this research is to investigate the mass production facility and evaluation of profitability for steam generator tubing in nuclear power plant. The equipment requirement and capacity, total investment cost, the evaluation of mass production yield and production cost accounting, the manufacturing technique standardization have been investigated. According to the result of evaluation of profitability, the project for SG tubing will be difficult to commercialize, but it can be considered the re-commercialize when the condition for investment is improving. The results of this research can be applicated to commercialize the precision tubes manufacturing which require similar process. 17 refs., 7 figs., 21 tabs. (Author)

  19. Noninflammatory fallopian tube pathology in children

    Energy Technology Data Exchange (ETDEWEB)

    Merlini, Laura; Anooshiravani, Mehrak; Hanquinet, Sylviane [University Hospital HUG, Unit of Pediatric Radiology, Geneva (Switzerland); Vunda, Aaron [University Hospital, Clinic of Pediatric Surgery, Geneva (Switzerland); Borzani, Irene; Napolitano, Marcello [Ospedale Buzzi, Pediatric Radiology, Milan (Italy)

    2008-12-15

    Noninflammatory tubal abnormalities are rare in children and usually not well covered by traditional educational material. The presenting symptoms are nonspecific and are common to many other conditions, so its preoperative diagnosis is rarely made. The purpose of this study was to review the hospital charts and imaging findings in children and sexually inactive adolescents who showed fallopian tube pathology. Understanding of the pertinent findings of previous imaging examinations might assist radiologists in making the correct preoperative diagnosis and increase the likelihood of preserving the fallopian tubes. The clinical entities described in this article include isolated tubal torsion, paratubal cysts, hydrosalpinx, undescended/ectopic fallopian tube, and tubal inguinal hernia. (orig.)

  20. Nervous system examination on YouTube

    OpenAIRE

    Azer Samy A; AlEshaiwi Sarah M; AlGrain Hala A; AlKhelaif Rana A

    2012-01-01

    Abstract Background Web 2.0 sites such as YouTube have become a useful resource for knowledge and are used by medical students as a learning resource. This study aimed at assessing videos covering the nervous system examination on YouTube. Methods A research of YouTube was conducted from 2 November to 2 December 2011 using the following key words “nervous system examination”, “nervous system clinical examination”, “cranial nerves examination”, “CNS examination”, “examination of cerebellum”, “...

  1. Air Liquide Space Pulse Tube Cryocoolers

    Science.gov (United States)

    Tanchon, J.; Trollier, T.; Buquet, J.; Ravex, A.; Crespi, P.

    2008-03-01

    Thanks to important internal development efforts completed and partial ESA funding, AL/DTA is now in position to propose two Pulse Tube cooler systems in the 40-80K temperature range for coming Earth Observation missions such as MTG, Sentinel 3, etc… The two pulse tube coolers thermo-mechanical units have been qualified against thermal and mechanical environment constraints. To complete these two Pulse Tube coolers, a Cooler Drive Electronic has been developed for active damping and vibration cancellation. The paper presents the current status of these products and associated Cooler Drive Electronics.

  2. Influence of furnace tube shapeon thermal strain of fire-tube boilers

    Directory of Open Access Journals (Sweden)

    Gaćeša Branka

    2014-01-01

    Full Text Available The aim of this paper is to use numerical analysis and fine element method-FEM to investigate the influence of furnace tube shape on the thermal strain of fire-tube boilers. Thermal stresses in corrugated furnace tubes of different shape, i.e. with different corrugation pitch and depth, were analysed first. It was demonstrated that the thermal stresses in corrugated furnace tube are significantly reduced with the increase of corrugation depth. Than deformations and stresses in the structure of a fire-tube boiler were analysed in a real operating condition, for the cases of installed plain furnace tube and corrugated furnace tubes with different shapes. It was concluded that in this fire-tube boiler, which is of larger steam capacity, the corrugated furnace tube must be installed, as well as that the maximal stress in the construction is reduced by the installation of the furnace tube with greater corrugation depth. The analysis of stresses due to pressure and thermal loads pointed out that thermal stresses are not lower-order stresses in comparison to stresses due to pressure loads, so they must be taken into consideration for boiler strength analysis. [Projekat Ministarstva nauke Republike Srbije, br. TR 35040 i br. TR 35011

  3. EFFECT OF TUBE PITCH ON HEAR TRANSFER IN SPRINKLED TUBE BUNDLE

    Directory of Open Access Journals (Sweden)

    Petr Kracík

    2015-10-01

    Full Text Available Water flowing on a sprinkled tube bundle forms three basic modes: the Droplet mode (the liquid drips from one tube to another, the Jet mode (with an increasing flow rate, the droplets merge into a column and the Membrane (Sheet mode (with a further increase in the flow rate of the falling film liquid, the columns merge and create sheets between the tubes. With a sufficient flow rate, the sheets merge at this stage, and the tube bundle is completely covered by a thin liquid film. There are several factors influencing both the individual modes and the heat transfer. Beside the above-mentioned falling film liquid flow rate, these are for instance the tube diameters, the tube pitches in the tube bundle, or the physical conditions of the falling film liquid. This paper presents a summary of data measured at atmospheric pressure, with a tube bundle consisting of copper tubes of 12 millimetres in diameter, and with a studied tube length of one meter. The tubes are situated horizontally one above another at a pitch of 15 to 30 mm, and there is a distribution tube placed above them with water flowing through apertures of 1.0mm in diameter at a 9.2mm span. Two thermal conditions have been tested with all pitches: 15 °C to 40 °C and 15 °C to 45 °C. The temperature of the falling film liquid, which was heated during the flow through the exchanger, was 15 °C at the distribution tube input. The temperature of the heating liquid at the exchanger input, which had a constant flow rate of approx. 7.2. litres per minute, was 40 °C, or alternatively 45 °C.

  4. Effect of display location on control-display stereotype strength for translational and rotational controls with linear displays.

    Science.gov (United States)

    Chan, Alan H S; Hoffmann, Errol R

    2015-01-01

    Experiments were designed to investigate the effects of control type and display location, relative to the operator, on the strength of control/display stereotypes. The Worringham and Beringer Visual Field principle and an extension of this principle for rotary controls (Hoffmann E.R., and Chan A.H.S. 2013). "The Worringham and Beringer 'Visual Field' Principle for Rotary Controls. Ergonomics." 56 (10): 1620-1624) indicated that, for a number of different control types (rotary and lever) on different planes, there should be no significant effect of the display location relative to the seated operator. Past data were surveyed and stereotype strengths listed. Experiments filled gaps where data are not available. Six different control types and seven display locations were used, as in the Frame of Reference Transformation Tool (FORT) model of Wickens et al. (Wickens, C.D., Keller, J.W., and Small, R.L. (2010). "Left. No, Right! Development of the Frame of Reference Transformation Tool (FORT)." Proceedings of the Human Factors and Ergonomics Society 54th Annual Meeting September 2010, 54: 1022-1026). Control/display arrangements with high stereotype strengths were evaluated yielding data for designers of complex control/display arrangements where the control and display are in different planes and for where the operator is moving. It was found possible to predict display/control arrangements with high stereotype strength, based on past data. Practitioner Summary: Controls and displays in complex arrangements need to have high compatibility. These experiments provide arrangements for six different controls (rotary and translational) and seven different display locations relative to the operator.

  5. Potential see-through performance deficits in U.S. Army developmental helmet-mounted displays

    Science.gov (United States)

    Harding, Thomas H.; Rash, Clarence E.

    2004-09-01

    The U.S. Army has several helmet-mounted displays (HMDs) under development, all with unique characteristics and designs. For example, the now cancelled RAH-66 Comanche HIDSS (Helmet Integrated Display Sighting System) uses miniature liquid crystal displays as sources, and Microvision, Inc., of Bothel, Washington, is developing several prototype HMDs for the Army that incorporate a scanning laser or lasers as their source. Gone are new HMD designs that use cathode ray tubes (CRTs) as sources. A potential problem for see-through displays lies in the fact that the MTF (modulation transfer function) of flat panel displays is characterized by a good high-spatial frequency response. Although this seems counterintuitive, this high frequency response may impact the see-through detection and identification of high-spatial frequency targets because of visual masking and/or spatial frequency adaptation. A similar problem exists with the HMDs being developed by Microvision, Inc., where a high-spatial frequency noise pattern is present due to the inclusion of a diffractive exit pupil expander. Simple blurring of the HMD imagery would reduce this potential problem. In an earlier investigation, we found that a little blurring of flat panel displays does not affect small letter acuity even near threshold. Thus, it is possible to reduce the potential for see-through deficits while still maintaining maximum HMD fidelity.

  6. Performance simulation of refrigerated display cabinets operating with refrigerants R22 and R404A

    Energy Technology Data Exchange (ETDEWEB)

    Ge, Y.T. [Mechanical Engineering, School of Engineering and Design, Brunel University, Uxbridge, Middlesex UB8 3PH (United Kingdom); Cropper, R. [Formerly School of Engineering, North East Wales Institute, Plas Coch Campus, Mold Road, Wrexham L11 2AW (United Kingdom)

    2008-08-15

    This paper describes the analysis and performance comparison of a display cabinet system using refrigerant R404A and its substitute refrigerant R22. The model of the display cabinet is developed at steady state and integrated from three main component sub-models, air-cooling finned-tube evaporator, air curtain and display cabinet body. The evaporator model is built up based on the distributed method, which can simulate the heat exchangers with different circuit structures. The frost effect on the performance of the evaporator is included in the model. The correlations for the heat transfer and pressure drop calculations of both air and refrigerant sides are purposely selected in the evaporator model. In addition, the evaporator model has been validated with experimental results at steady states from published literature. Several correlated functions from the detailed numerical solution are used for the model of the air curtain. Some simplifications are also utilized for the model of display cabinet body. The performance simulation and comparison of the display cabinet using refrigerants R404A and R22 are carried out at different indoor ambient conditions especially at varied ambient air humidity to mimic the actual indoor space conditions in super stores. Some significant results such as the comparison of cooling load requirement for different refrigerant display cases have been obtained from the simulation, which can significantly contribute to the optimal cabinet design and operating analysis. (author)

  7. Grey-scale reversed radiographic display in the detection of approximal caries.

    Science.gov (United States)

    Haak, Rainer; Wicht, Michael J

    2005-01-01

    Purpose of this study was to determine the influence of grey-scale reversal of digital radiographic images on the detection of proximal caries. Five observers assessed digital bitewing radiographs (Sidexis((R)), Sirona) of 320 unrestored surfaces of extracted posterior teeth embedded in 20 models, simulating pairing of maxillary and mandibular arches, using a six-category caries rating scale. Images were displayed in normal [N] and inverse [IN] mode at different image sizes (display ratio: 1:1, 1:2, 1:7) on a cathode-ray tube monitor (Nokia 446 XS) and a TFT display (Panasonic LC 50 S). Validation standard was defined as histological lesion depth. Validity was expressed as areas under receiver operating characteristic curves (AUC) calculated for two levels of histological caries penetration: presence of caries and presence of a dentine lesion. The factors 'inverse display', 'image size on-screen' 'display type' and 'disease cut-off' were analysed by repeated measures ANOVA. Inverse image display significantly influenced the diagnostic validity (P=0.014), but a reduced accuracy was only seen at the lowest image size (AUC (SE): [N] 0.64 (0.02); [IN] 0.62 (0.02)). At the validation threshold 'dentine caries' approximal caries detection deteriorated when using grey-scale reversal (AUC (SE): [N] 0.71 (0.02); [IN] 0.69 (0.02)). In conclusion, grey-scale reversal of digital radiographs did not optimise approximal caries detection and aggravated the detectability of dentinal lesions.

  8. Optimization of light field display-camera configuration based on display properties in spectral domain.

    Science.gov (United States)

    Bregović, Robert; Kovács, Péter Tamás; Gotchev, Atanas

    2016-02-08

    The visualization capability of a light field display is uniquely determined by its angular and spatial resolution referred to as display passband. In this paper we use a multidimensional sampling model for describing the display-camera channel. Based on the model, for a given display passband, we propose a methodology for determining the optimal distribution of ray generators in a projection-based light field display. We also discuss the required camera setup that can provide data with the necessary amount of details for such display that maximizes the visual quality and minimizes the amount of data.

  9. Characterising laser beams with liquid crystal displays

    CSIR Research Space (South Africa)

    Dudley, Angela L

    2016-09-01

    Full Text Available decomposition of light has been known for a long time, applied mostly to pattern recognition, we illustrate how this technique can be implemented with the use of liquid-crystal displays. We show experimentally how liquid crystal displays can be used to infer...

  10. Ribosome display for improved biotherapeutic molecules.

    Science.gov (United States)

    Rothe, Achim; Hosse, Ralf J; Power, Barbara E

    2006-02-01

    Ribosome display presents an innovative in vitro technology for the rapid isolation and evolution of high-affinity peptides or proteins. Displayed proteins are bound to and recovered from target molecules in multiple rounds of selection in order to enrich for specific binding proteins. No transformation step is necessary, which could lead to a loss of library diversity. A cycle of display and selection can be performed in one day, enabling the existing gene repertoire to be rapidly scanned. Proteins isolated from the panning rounds can be further modified through random or directed molecular evolution for affinity maturation, as well as selected for characteristics such as protein stability, folding and functional activity. Recently, the field of display technologies has become more prominent due to the generation of new scaffolds for ribosome display, isolation of high-affinity human antibodies by phage display, and their implementation in the discovery of novel protein-protein interactions. Applications for this technology extend into the broad field of antibody engineering, proteomics, and synthetic enzymes for diagnostics and therapeutics in cancer, autoimmune and infectious diseases, neurodegenerative diseases and inflammatory disorders. This review highlights the role of ribosome display in drug discovery, discusses advantages and disadvantages of the system, and attempts to predict the future impact of ribosome display technology on the development of novel engineered biopharmaceutical products for biological therapies.

  11. (Hibiscus sabdariffa L.) roots by differential display

    African Journals Online (AJOL)

    aghomotsegin

    2014-12-31

    Dec 31, 2014 ... display reverse transcriptase PCR (DDRT-PCR) was used to compare the overall differences in gene ... Abbreviations: DDRT-PCR, Differential display reverse transcriptase polymerase chain reaction, ESTs, expressed sequence tags; ... Agricultural Research Corporation's Obeid Research Substation in.

  12. A visual-display and storage device

    Science.gov (United States)

    Bosomworth, D. R.; Moles, W. H.

    1972-01-01

    Memory and display device uses cathodochromic material to store visual information and fast phosphor to recall information for display and electronic processing. Cathodochromic material changes color when bombarded with electrons, and is restored to its original color when exposed to light of appropiate wavelength.

  13. Factors affecting dwell times on digital displaying

    Science.gov (United States)

    Williams, A. J.; Harris, R. L., Sr.

    1985-01-01

    A series of exploratory tests were conducted to investigate the effects of advanced display formats and display media on pilot scanning behavior using Langley's oculometer, a desktop flight simulator, a conventional electro-mechanical meter, and various digital displays. The primary task was for the test subject to maintain level flight, on a specific course heading, during moderate turbulence. A secondary task of manually controlling the readout of a display was used to examine the effects of the display format on a subject's scan behavior. Secondary task scan parameters that were evaluated were average dwell time, dwell time histograms, and number of dwells per meter change. The round dial meter demonstrated shorter dwell times and fewer dwells per meter change than the digital displays. The following factors affected digital display scanning behavior: (1) the number of digits; (2) the update rate of the digits; (3) the display media; and (4) the character font. The size of the digits used in these tests (0.28 to 0.50 inches) did not affect scan behavior measures.

  14. Coordinated Displays to Assist Cyber Defenders

    Science.gov (United States)

    2016-09-23

    checks: Detecting satisficing to increase statistical power. Journal of Experimental Social Psychology , 45, 867-872. Scarfone, K., & Mell, P. (2007...regardless of display condition (coordinated or uncoordinated). METHOD Participants & Experimental Design In this experiment, 46 people (19...previous experience in cyber defense. Experimental Design This study featured a single experimental factor, display condition, and a control

  15. Monitor displays in radiology: Part 2

    OpenAIRE

    INDRAJIT, IK; Verma, BS

    2009-01-01

    Monitor displays play an important role in modern radiology practice. Practicing radiologists need to be familiar with the various performance parameters of medical-grade displays. A certain amount of technical knowledge is useful when making purchasing decisions since the right choice of equipment can have a great impact on the accuracy, efficiency, and speed in the radiology department.

  16. 33 CFR 4.02 - Display.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Display. 4.02 Section 4.02 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY GENERAL OMB CONTROL NUMBERS ASSIGNED PURSUANT TO THE PAPERWORK REDUCTION ACT § 4.02 Display. 33 CFR part or section where identified...

  17. 49 CFR 509.2 - Display.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 6 2010-10-01 2010-10-01 false Display. 509.2 Section 509.2 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION OMB CONTROL NUMBERS FOR INFORMATION COLLECTION REQUIREMENTS § 509.2 Display. 49 CFR...

  18. 41 CFR 60-999.2 - Display.

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 1 2010-07-01 2010-07-01 true Display. 60-999.2 Section 60-999.2 Public Contracts and Property Management Other Provisions Relating to Public Contracts... CONTROL NUMBERS FOR OFCCP INFORMATION COLLECTION REQUIREMENTS § 60-999.2 Display. 41 CFR Part where the...

  19. Display Developer for Firing Room Applications

    Science.gov (United States)

    Bowman, Elizabeth A.

    2013-01-01

    The firing room at Kennedy Space Center (KSC) is responsible for all NASA human spaceflight launch operations, therefore it is vital that all displays within the firing room be properly tested, up-to-date, and user-friendly during a launch. The Ground Main Propulsion System (GMPS) requires a number of remote displays for Vehicle Integration and Launch (VIL) Operations at KSC. My project is to develop remote displays for the GMPS using the Display Services and Framework (DSF) editor. These remote displays will be based on model images provided by GMPS through PowerPoint. Using the DSF editor, the PowerPoint images can be recreated with active buttons associated with the correct Compact Unique Identifiers (CUIs). These displays will be documented in the Software Requirements and Design Specifications (SRDS) at the 90% GMPS Design Review. In the future, these remote displays will be available for other developers to improve, edit, or add on to so that the display may be incorporated into the firing room to be used for launches.

  20. Pneumatosis intestinalis associated with enteral tube feeding

    National Research Council Canada - National Science Library

    Zorgdrager, Marcel; Pol, Robert

    2013-01-01

    ...). Explorative laparotomy showed an omental band adhesion without signs of ischaemia. After a short period of total parenteral nutrition PI resolved almost completely and enteral tube feeding could be continued once again...

  1. Automatic welding of stainless steel tubing

    Science.gov (United States)

    Clautice, W. E.

    1978-01-01

    The use of automatic welding for making girth welds in stainless steel tubing was investigated as well as the reduction in fabrication costs resulting from the elimination of radiographic inspection. Test methodology, materials, and techniques are discussed, and data sheets for individual tests are included. Process variables studied include welding amperes, revolutions per minute, and shielding gas flow. Strip chart recordings, as a definitive method of insuring weld quality, are studied. Test results, determined by both radiographic and visual inspection, are presented and indicate that once optimum welding procedures for specific sizes of tubing are established, and the welding machine operations are certified, then the automatic tube welding process produces good quality welds repeatedly, with a high degree of reliability. Revised specifications for welding tubing using the automatic process and weld visual inspection requirements at the Kennedy Space Center are enumerated.

  2. Caring for Your Percutaneous Nephrostomy Tube

    Science.gov (United States)

    ... and medication through this line.  You will be awake, relaxed, and maybe a little sleepy during the ... tube.  If you have low urine output or dark, foul- Patient Information Procedure 1. Thoroughly wash your ...

  3. Screening for Open Neural Tube Defects.

    Science.gov (United States)

    Krantz, David A; Hallahan, Terrence W; Carmichael, Jonathan B

    2016-06-01

    Biochemical prenatal screening was initiated with the use of maternal serum alpha fetoprotein to screen for open neural tube defects. Screening now includes multiple marker and sequential screening protocols involving serum and ultrasound markers to screen for aneuploidy. Recently cell-free DNA screening for aneuploidy has been initiated, but does not screen for neural tube defects. Although ultrasound is highly effective in identifying neural tube defects in high-risk populations, in decentralized health systems maternal serum screening still plays a significant role. Abnormal maternal serum alpha fetoprotein alone or in combination with other markers may indicate adverse pregnancy outcome in the absence of open neural tube defects. Copyright © 2016 Elsevier Inc. All rights reserved.

  4. The Choking Game on YouTube

    Directory of Open Access Journals (Sweden)

    Ellen K. Defenderfer MS

    2016-03-01

    Full Text Available The choking game (TCG is an adolescent activity in which asphyxiation is used to obtain a “high,” occasionally resulting in seizures or death. A plethora of TCG information is available through YouTube, though this content has not been evaluated recently. The current study described TCG as portrayed in YouTube videos and compared views and ratings of TCG videos to unrelated videos. The TCG videos demonstrated diverse methods of asphyxiation, with a minority showing injury to the participants. TCG videos were less likely to be commented on or rated positively than non–choking game videos. TCG prevention videos differed significantly from actual TCG videos in the way they depicted the social context of TCG. Thus, TCG videos are accessible through YouTube, but the prevention materials available on YouTube are not accurate or representative. Accurate and educational online prevention materials should be created to decrease the occurrence of TCG.

  5. Multimode Traveling-Wave Amplifier Tubes

    Science.gov (United States)

    Buck, E.

    1981-02-01

    The paper examines the recent developments which makes the Traveling Wave Tube (TWT) more powerful and efficient as a microwave amplifier than the solid state devices. Basic workings and efficiency, which can run, but usually do not, to 55%, are examined. The dependence of the performance of a given TWT upon the qualities of the beam and the manner of its focusing is described. Also described is the development of a multistage depressed collector (MDC) and its first application to a Communication Technology Satellite (CTS) tube, a 12 GHz, coupled-cavity, 200 watt TWT, which resulted in being operated in space for nearly four years and was both the most powerful and the most efficient (around 50%) communications TWT ever flown. It is predicted that the application of efficient refocusing and MDCs, made possible by computer simulations, will greatly increase tube efficiency, and thereby make practical, new multimode tubes which operate, as least partly, in a linear fashion.

  6. Gastroenteric tube feeding: Techniques, problems and solutions

    National Research Council Canada - National Science Library

    Irina Blumenstein Yogesh M Shastri Jürgen Stein

    2014-01-01

    Gastroenteric tube feeding plays a major role in the management of patients with poor voluntary intake,chronic neurological or mechanical dysphagia or gut dysfunction,and patients who are critically...

  7. Medical Informatics Idle YouTube Potential.

    Science.gov (United States)

    Hucíková, Anežka; Babic, Ankica

    2017-01-01

    YouTube as an online video-sharing service in the context of Web 2.0 goes beyond the bounds of pure fun, for which the platform was primarily established. Nowadays, commonly to other social media, it serves also educational, informational and last but not least, marketing purposes. The importance of video sharing is supported by several predictions about video reaching over 90% of global internet traffic by 2020. Using qualitative content analysis over selected YouTube videos, paper examines the current situation of the platform's marketing potential usage by medical informatics organizations, researches and other healthcare professionals. Results of the analysis demonstrate several ways in which YouTube is already used to inform, educate or promote above-mentioned medical institutions. However, their engagement in self-promo or spreading awareness of their research projects via YouTube is considered to be low.

  8. YouTube and ‘psychiatry’

    Science.gov (United States)

    Gordon, Robert; Miller, John; Collins, Noel

    2015-01-01

    YouTube is a video-sharing website that is increasingly used to share and disseminate health-related information, particularly among younger people. There are reports that social media sites, such as YouTube, are being used to communicate an anti-psychiatry message but this has never been confirmed in any published analysis of YouTube clip content. This descriptive study revealed that the representation of ‘psychiatry’ during summer 2012 was predominantly negative. A subsequent smaller re-analysis suggests that the negative portrayal of ‘psychiatry’ on YouTube is a stable phenomenon. The significance of this and how it could be addressed are discussed. PMID:26755987

  9. A review of pulse tube refrigeration

    Science.gov (United States)

    Radebaugh, Ray

    1990-01-01

    This paper reviews the development of the three types of pulse tube refrigerators: basic, resonant, and orifice types. The principles of operation are given. It is shown that the pulse tube refrigerator is a variation of the Stirling-cycle refrigerator, where the moving displacer is substituted by a heat transfer mechanism or by an orifice to bring about the proper phase shifts between pressure and mass flow rate. A harmonic analysis with phasors is described which gives reasonable results for the refrigeration power, yet is simple enough to make clear the processes which give rise to the refrigeration. The efficiency and refrigeration power are compared with those of other refrigeration cycles. A brief review is given of the research being done at various laboratories on both one- and two-stage pulse tubes. A preliminary assessment of the role of pulse tube refrigerators is discussed.

  10. Opioid Use and Neural Tube Defects

    Science.gov (United States)

    ... CDC.gov . Error processing SSI file Key Findings: Opioid Use and Neural Tube Defects Recommend on Facebook ... new study that looked at the use of opioids during pregnancy and their relationship to having a ...

  11. Routine jejunostomy tube feeding following esophagectomy

    National Research Council Canada - National Science Library

    Weijs, Teus J; van Eden, Hanneke W.J; Ruurda, Jelle P.|info:eu-repo/dai/nl/257561021; Luyer, Misha D P; Steenhagen, Elles|info:eu-repo/dai/nl/304815713; Nieuwenhuijzen, Grard A P; van Hillegersberg, Richard|info:eu-repo/dai/nl/110706242

    2017-01-01

    Background: Malnutrition is an important problem following esophagectomy. A surgically placed jejunostomy secures an enteral feeding route, facilitating discharge with home-tube feeding and long-term nutritional support...

  12. Accidental Decannulation OF TRACHEOSTOMY TUBES - Case Series.

    Science.gov (United States)

    Omokanye, H K; Dunmade, A D; Segun-Busari, S; Afolabi, O A; Habeeb, O G; Adegboye, M B; Alabi, B S

    2016-01-01

    Tracheostomy tube (TT) is usually removed in a planned manner once the patient ceases to have the condition that necessitated the procedure. Accidental decannulation or extubation refers to inadvertent removal of tracheostomy tube out of the stoma. It could prove fatal in an otherwise stable patient. We review a variety of unexpected and often-overlooked causes of accidental decannulation with suggestions on preventive measures. We therefore present three cases of accidental decannulation of tracheostomy tubes in order to report our experiences in the management of the condition. Accidental decannulation occurs both in hospitalized and patient on home care of their tracheostomy tubes. Reduction in neck circumference due to weight loss predisposes to accidental decannulation, which could be prevented by suturing the flange to the skin.

  13. Stabilization Strategies for Drift Tube Linacs

    CERN Document Server

    AUTHOR|(CDS)2085420; Lamehi Rashti, Mohammad

    The average axial electric fields in drift tube linac cavities are known to be sensitive with respect to the perturbation errors. Postcoupler is a powerful stabilizer devices that is used to reduce this sensitivity of average axial field. Postcouplers are the cylindrical rod which is extended from cavity wall toward the drift tube without touching the drift tube surface. Postcouplers need to be adjusted to the right length to stabilize the average axial field. Although postcouplers are used successfully in many projects, there is no straightforward procedure for postcouplers adjustment and it has been done almost based on trial and errors. In this thesis, the physics and characteristics of postcouplers has been studied by using an equivalent circuit model and 3D finite element method calculations. Finally, a straightforward and accurate method to adjust postcouplers has been concluded. The method has been verified by using experimental measurements on CERN Linac4 drift tube linac cavities.

  14. SPECIAL PURPOSE SHOCK TUBE for BLAST ASSESSMENT

    Data.gov (United States)

    Federal Laboratory Consortium — This device is a specially designed shock tube for testing fabric samples in a controlled environment. The device determines the appropriate types of sensors to be...

  15. Metal bellows custom-fabricated from tubing

    Science.gov (United States)

    1965-01-01

    Mandrel assembly mounted in a lathe chuck is used with a forming wheel to roll-form bellows from standard sheet metal tubing. Spacers and mandrels of various sizes custom-fabricate bellows of any desired dimensions.

  16. Inverse Kinematics of Concentric Tube Steerable Needles.

    Science.gov (United States)

    Sears, Patrick; Dupont, Pierre E

    2007-01-01

    Prior papers have introduced steerable needles composed of precurved concentric tubes. The curvature and extent of these needles can be controlled by the relative rotation and translation of the individual tubes. Under certain assumptions on the geometry and design of these needles, the forward kinematics problem can be solved in closed form by means of algebraic equations. The inverse kinematics problem, however, is not as straightforward owing to the nonlinear map between relative tube displacements and needle tip configuration as well as to the multiplicity of solutions as the number of tubes increases. This paper presents a general approach to solving the inverse kinematics problem using a pseudoinverse solution together with gradients of nullspace potential functions to enforce geometric and mechanical constraints.

  17. Optimizing Tube Precurvature to Enhance Elastic Stability of Concentric Tube Robots.

    Science.gov (United States)

    Ha, Junhyoung; Park, Frank C; Dupont, Pierre E

    2017-02-01

    Robotic instruments based on concentric tube technology are well suited to minimally invasive surgery since they are slender, can navigate inside small cavities and can reach around sensitive tissues by taking on shapes of varying curvature. Elastic instabilities can arise, however, when rotating one precurved tube inside another. In contrast to prior work that considered only tubes of piecewise constant precurvature, we allow precurvature to vary along the tube's arc length. Stability conditions for a planar tube pair are derived and used to formulate an optimal design problem. An analytic formulation of the optimal precurvature function is derived that achieves a desired tip orientation range while maximizing stability and respecting bending strain limits. This formulation also includes straight transmission segments at the proximal ends of the tubes. The result, confirmed by both numerical and physical experiment, enables designs with enhanced stability in comparison to designs of constant precurvature.

  18. Holistic peripheral processing of a polygon display.

    Science.gov (United States)

    Hughes, T; MacRae, A W

    1994-12-01

    Polygon displays compress information that would otherwise be conveyed by separate indicators into a single display in which each reading is represented by the distance of a polygon vertex from its center. The effect on detection of fault states of varying the number of polygon vertices from 4 to 20 in a display presented peripherally around a dynamic, simulated flight display was studied. Presence of the dynamic task reduced both speed and accuracy of response to the polygon display but did not significantly affect the pattern of response to differing numbers of vertices. All measures of performance were better with larger numbers of vertices. If the vertices are processed serially, more vertices require more processing time. Therefore, the result argues for holistic processing and implies that such information integration is beneficial to human performance in fault detection.

  19. Three-dimensional hologram display system

    Science.gov (United States)

    Mintz, Frederick (Inventor); Chao, Tien-Hsin (Inventor); Bryant, Nevin (Inventor); Tsou, Peter (Inventor)

    2009-01-01

    The present invention relates to a three-dimensional (3D) hologram display system. The 3D hologram display system includes a projector device for projecting an image upon a display medium to form a 3D hologram. The 3D hologram is formed such that a viewer can view the holographic image from multiple angles up to 360 degrees. Multiple display media are described, namely a spinning diffusive screen, a circular diffuser screen, and an aerogel. The spinning diffusive screen utilizes spatial light modulators to control the image such that the 3D image is displayed on the rotating screen in a time-multiplexing manner. The circular diffuser screen includes multiple, simultaneously-operated projectors to project the image onto the circular diffuser screen from a plurality of locations, thereby forming the 3D image. The aerogel can use the projection device described as applicable to either the spinning diffusive screen or the circular diffuser screen.

  20. A new emissive projection display technology and a high contrast DLP projection display on black screen

    Science.gov (United States)

    Sun, Ted X.; Cheng, Botao

    2011-03-01

    In this paper, Sun Innovations demonstrates an innovative emissive projection display (EPD) system. It is comprised of a fully transparent fluorescent screen with a UV image projector. The screen can be applied to glass windows or windshield, without affecting visible light transmission. The UV projector can be based on either a DLP (digital light processor) or a laser scanner display engine. For a DLP based projector, a discharge lamp coupled to a set of UV filters can be applied to generate a full color video image on the transparent screen. UV or blue-ray laser diodes of different wavelengths can be combined with scanning mirrors to generate a vector display for full windshield display applications. This display combines the best of both worlds of conventional projection and emissive display technologies. Like a projection display, the screen has no pixel structure and can be manufactured roll to roll; the display is scalable. Like an emissive display (e.g. plasma or CRT), the quality of the image is superior, with very large viewing angles. It also offers some unique features. For example, in addition to a fully transparent display on windows or windshields, it can be applied to a black substrate to create the first front projection display on true "black" screen that has superior image contrast at low projection power. This fundamentally new display platform can enable multiple major commercial applications that can not be addressed by any of the existing display technologies.

  1. SNORKEL TRACHEOTOMY TUBE FOR RESPIRATOR USE

    Science.gov (United States)

    Lebo, Charles P.

    1954-01-01

    The Snorkel tracheotomy tube, a simple modification of the standard tube, overcomes many of the mechanical inconveniences usually encountered in the care of patients with tracheotomy who have to be kept in respirators. With it in place, it is not necessary to use special devices to hold the collar of the respirator away from the site of the tracheal incision. Nursing care of the patient is made easier. ImagesFigure 2.Figure 3. PMID:13182610

  2. Accidental Decannulation OF TRACHEOSTOMY TUBES - Case Series

    OpenAIRE

    Omokanye, HK; Dunmade, AD; Segun-Busari, S; Afolabi, OA; Habeeb, OG; Adegboye, MB; Alabi, BS

    2016-01-01

    Tracheostomy tube (TT) is usually removed in a planned manner once the patient ceases to have the condition that necessitated the procedure. Accidental decannulation or extubation refers to inadvertent removal of tracheostomy tube out of the stoma. It could prove fatal in an otherwise stable patient. We review a variety of unexpected and often-overlooked causes of accidental decannulation with suggestions on preventive measures. We therefore present three cases of accidental decannulation of ...

  3. A Flue Gas Tube for Thermoelectric Generator

    DEFF Research Database (Denmark)

    2013-01-01

    The invention relates to a flue gas tube (FGT) (1) for generation of thermoelectric power having thermoelectric elements (8) that are integrated in the tube. The FTG may be used in combined heat and power (CHP) system (13) to produce directly electricity from waste heat from, e.g. a biomass boiler....... The CHP system may also be operated in a heating or cooling mode, thus being able to heat or cool water by feeding electricity to the system....

  4. Explosively Bonded Gun Tube Liner Development

    Science.gov (United States)

    2015-04-01

    some concern was the occasional appearance of iron-Ta intermetallics near the liner-steel interface. This is a brittle phase and subject to...Montgomery JS, de Rosset WS. Examination of intermetallic phases and residual stresses resulting from explosive bonding of refractory metal gun tube...caliber smoothbore gun tube. The metallic bond produced by explosive bonding is extremely strong and presumably would keep the liner in place. In Phase

  5. Tube current reduction in pediatric non-ECG-gated heart CT by combined tube current modulation.

    Science.gov (United States)

    Goo, Hyun Woo; Goo, Hyum Woo; Suh, Dong Soo

    2006-04-01

    Dose reduction by combined tube current modulation has not been evaluated in pediatric low-dose CT. This study was performed to evaluate tube current reduction in non-ECG-gated heart CT angiography in children by combined tube current modulation, and to assess the effects of body weight, age, sex, and scan direction on tube current reduction. From September 2004 to January 2005, non-ECG-gated heart CT examinations were performed with combined tube current modulation in 50 children (median age 1 year, range 1 month to 16 years; M/F 29/21) with congenital heart disease. Sixteen-slice spiral CT studies were obtained using a weight-based low-dose protocol (80 kVp, 50-160 effective mA). CT scans were obtained in the craniocaudal direction when leg veins (n=36) were used for IV injection of contrast agent and in the caudocranial direction when arm veins (n=13) were used. In one child who underwent a Fontan operation, both arm and leg veins were used. We calculated tube current reduction by combined tube current modulation and evaluated the effects of body weight, age, sex, and scan technique on tube current reduction. The quality of CT angiography images was visually evaluated by an experienced pediatric radiologist. Overall tube current reduction by combined tube current modulation was 15.8+/-11.1%. The reduction was variable among five body weight groups (9.3+/-7.9% for ECG-gated heart CT by 15.8% without degradation of image quality. With our CT protocol, for body weights up to 39.9 kg, age showed a significant positive correlation with tube current reduction, but there was a lower dose-saving effect in children heavier than 40 kg. Tube current reduction was not affected by sex, but was affected by scan direction.

  6. Investigations on high-pressure ribbed tubes

    Energy Technology Data Exchange (ETDEWEB)

    Kling, G.

    1942-05-01

    During hydrogenation of coal, the reactants (coal paste and hydrogen) had to be heated to reaction temperature partly by heat exchange with products and partly by heating in hairpin tubes of a preheater. These hairpin tubes were heated externally by hot circulating gases. In order to improve heat transfer from the gases to the tubes, various types of metal ribbing were welded to the tubes to catch more heat and transfer it to the tubes. This report detailed some studies on the best shapes and dimensions and numbers of plates to be used. The report was limited to flat, rectangular-cross-section plates attached perpendicularly, instead of including flat circular plates, spiral plates, or other configurations. The advantage of greater surface area to catch more heat had to be balanced off against the disadvantage of greater surface area to absorb more heat in internal resistance to heat flow. The report described the experimental conditions, the modifications tested, and the shape decided upon as best for flat plates. Some of the diagrams illustrating temperature distributions around the tubes and ribs were presented in imitation three-dimenional formats. 16 figures.

  7. [Odor sensing system and olfactory display].

    Science.gov (United States)

    Nakamoto, Takamichi

    2014-01-01

    In this review, an odor sensing system and an olfactory display are introduced into people in pharmacy. An odor sensing system consists of an array of sensors with partially overlapping specificities and pattern recognition technique. One of examples of odor sensing systems is a halitosis sensor which quantifies the mixture composition of three volatile sulfide compounds. A halitosis sensor was realized using a preconcentrator to raise sensitivity and an electrochemical sensor array to suppress the influence of humidity. Partial least squares (PLS) method was used to quantify the mixture composition. The experiment reveals that the sufficient accuracy was obtained. Moreover, the olfactory display, which present scents to human noses, is explained. A multi-component olfactory display enables the presentation of a variety of smells. The two types of multi-component olfactory display are described. The first one uses many solenoid valves with high speed switching. The valve ON frequency determines the concentration of the corresponding odor component. The latter one consists of miniaturized liquid pumps and a surface acoustic wave (SAW) atomizer. It enables the wearable olfactory display without smell persistence. Finally, the application of the olfactory display is demonstrated. Virtual ice cream shop with scents was made as a content of interactive art. People can enjoy harmony among vision, audition and olfaction. In conclusion, both odor sensing system and olfactory display can contribute to the field of human health care.

  8. Advance in phage display technology for bioanalysis.

    Science.gov (United States)

    Tan, Yuyu; Tian, Tian; Liu, Wenli; Zhu, Zhi; J Yang, Chaoyong

    2016-06-01

    Phage display technology has emerged as a powerful tool for target gene expression and target-specific ligand selection. It is widely used to screen peptides, proteins and antibodies with the advantages of simplicity, high efficiency and low cost. A variety of targets, including ions, small molecules, inorganic materials, natural and biological polymers, nanostructures, cells, bacteria, and even tissues, have been demonstrated to generate specific binding ligands by phage display. Phages and target-specific ligands screened by phage display have been widely used as affinity reagents in therapeutics, diagnostics and biosensors. In this review, comparisons of different types of phage display systems are first presented. Particularly, microfluidic-based phage display, which enables screening with high throughput, high efficiency and integration, is highlighted. More importantly, we emphasize the advances in biosensors based on phages or phage-derived probes, including nonlytic phages, lytic phages, peptides or proteins screened by phage display, phage assemblies and phage-nanomaterial complexes. However, more efficient and higher throughput phage display methods are still needed to meet an explosion in demand for bioanalysis. Furthermore, screening of cyclic peptides and functional peptides will be the hotspot in bioanalysis. Copyright © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. The display of portable infrared measuring temperature

    Science.gov (United States)

    Qian, Yitao; Gu, Guohua; Sui, Xiubao

    2014-11-01

    In recent years based on security, quality supervision, inspection and medical for the urgent need of infrared temperature measurement and infrared display technology, coupled with embedded system to achieve rapid development, which is widely used in the electronic products and the field of intelligent instruments and industrial control, this paper has designed a kind of more comprehensive, more efficient and more intuitive infrared thermometer. Unlike previous handheld infrared thermometer, we regard an embedded Linux system as the system, with its open source code, support most mainstream hardware platforms, unified peripheral interface and can be customized, to build an embedded infrared system that has provided strong system support; the pseudocolor techniques and Qt interface display technology make the image more colorful and the picture function more diverse; With ARM microprocessor as the display and temperature measuring platform, it costs reduction and reduce volume and power consumption; the FrameBuffer interface technology and multithreading technology realize the smooth real-time display. And ultimately the display size of real-time infrared image is 640 * 480 at a speed of 25 frames / sec. What is more, display is equipped with the menu option so that thermometer can be required to complete the operation through the button. The temperature display system aims at small volume, easy to use and flexible. I believe this thermometer will have a good application prospect.

  10. Advanced Ultrasupercritical (AUSC) Tube Membrane Panel Development

    Energy Technology Data Exchange (ETDEWEB)

    Pschirer, James [Alstom Power Inc., Windsor, CT (United States); Burgess, Joshua [Alstom Power Inc., Windsor, CT (United States); Schrecengost, Robert [Alstom Power Inc., Windsor, CT (United States)

    2017-08-16

    Alstom Power Inc., a wholly owned subsidiary of the General Electric Company (GE), has completed the project “Advanced Ultrasupercritical (AUSC) Tube Membrane Panel Development” under U.S. Department of Energy (DOE) Award Number DE-FE0024076. This project was part of DOE’s Novel Crosscutting Research and Development to Support Advanced Energy Systems program. AUSC Tube Membrane Panel Development was a two and one half year project to develop and verify the manufacturability and serviceability of welded tube membrane panels made from high performance materials suitable for the AUSC steam cycles, defined as high pressure steam turbine inlet conditions of 700-760°C (1292-1400°F) and 24.5-35MPa (3500-5000psi). The difficulty of this challenge lies in the fact that the membrane-welded construction imposes demands on the materials that are unlike any that exist in other parts of the boiler. Tube membrane panels have been designed, fabricated, and installed in boilers for over 50 years with relatively favorable experience when fabricated from carbon and Cr-Mo low alloy steels. The AUSC steam cycle requires membrane tube panels fabricated from materials that have not been used in a weldment with metal temperatures in the range of 582-610°C (1080-1130°F). Fabrication materials chosen for the tubing were Grade 92 and HR6W. Grade 92 is a creep strength enhanced ferritic Cr-Mo alloy and HR6W is a high nickel alloy. Once the materials were chosen, GE performed the engineering design of the panels, prepared shop manufacturing drawings, and developed manufacturing and inspection plans. After the materials were purchased, GE manufactured and inspected the tube membrane panels, determined if post fabrication heat treatment of the tube membrane panels was needed, performed pre- and post-weld heat treatment on the Grade 92 panels, conducted final nondestructive inspection of any heat treated tube membrane panels, conducted destructive inspection of the completed tube

  11. Transparent 3D display for augmented reality

    Science.gov (United States)

    Lee, Byoungho; Hong, Jisoo

    2012-11-01

    Two types of transparent three-dimensional display systems applicable for the augmented reality are demonstrated. One of them is a head-mounted-display-type implementation which utilizes the principle of the system adopting the concave floating lens to the virtual mode integral imaging. Such configuration has an advantage in that the threedimensional image can be displayed at sufficiently far distance resolving the accommodation conflict with the real world scene. Incorporating the convex half mirror, which shows a partial transparency, instead of the concave floating lens, makes it possible to implement the transparent three-dimensional display system. The other type is the projection-type implementation, which is more appropriate for the general use than the head-mounted-display-type implementation. Its imaging principle is based on the well-known reflection-type integral imaging. We realize the feature of transparent display by imposing the partial transparency to the array of concave mirror which is used for the screen of reflection-type integral imaging. Two types of configurations, relying on incoherent and coherent light sources, are both possible. For the incoherent configuration, we introduce the concave half mirror array, whereas the coherent one adopts the holographic optical element which replicates the functionality of the lenslet array. Though the projection-type implementation is beneficial than the head-mounted-display in principle, the present status of the technical advance of the spatial light modulator still does not provide the satisfactory visual quality of the displayed three-dimensional image. Hence we expect that the head-mounted-display-type and projection-type implementations will come up in the market in sequence.

  12. Real-Time, Interactive Sonic Boom Display

    Science.gov (United States)

    Haering, Jr., Edward A. (Inventor); Plotkin, Kenneth J. (Inventor)

    2012-01-01

    The present invention is an improved real-time, interactive sonic boom display for aircraft. By using physical properties obtained via various sensors and databases, the invention determines, in real-time, sonic boom impacts locations and intensities for aircraft traveling at supersonic speeds. The information is provided to a pilot via a display that lists a selectable set of maneuvers available to the pilot to mitigate sonic boom issues. Upon selection of a maneuver, the information as to the result of the maneuver is displayed and the pilot may proceed with making the maneuver, or provide new data to the system in order to calculate a different maneuver.

  13. Testing of Colorimetric Tubes for Nitrogen Dioxide and Monomethylhydrazine.

    Science.gov (United States)

    Diamond, Philip

    Colorimetric tubes for nitrogen dioxide (NO2) and monomethylhydrazine (MMH) were tested for accuracy and results indicate that at the levels checked the tubes' average deviation was plus or minus 20 percent. Tube NO2 concentrations all read lower than the analyzed concentrations. MMH tubes read much higher than the analyzed concentration of 0.28…

  14. 16 CFR 1507.12 - Multiple-tube fireworks devices.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Multiple-tube fireworks devices. 1507.12... REGULATIONS FIREWORKS DEVICES § 1507.12 Multiple-tube fireworks devices. (a) Application. Multiple-tube mine and shell fireworks devices with any tube measuring 1.5 inches (3.8 cm) or more in inside diameter and...

  15. 21 CFR 888.4230 - Cement ventilation tube.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Cement ventilation tube. 888.4230 Section 888.4230...) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.4230 Cement ventilation tube. (a) Identification. A cement ventilation tube is a tube-like device usually made of plastic intended to be inserted into...

  16. 46 CFR 153.979 - Gauging with a sounding tube.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Gauging with a sounding tube. 153.979 Section 153.979... Procedures § 153.979 Gauging with a sounding tube. (a) No person may remove the cover of a sounding tube... cargo transfer may not authorize removal of the cover from a sounding tube gauge unless all tank...

  17. 21 CFR 870.4390 - Cardiopulmonary bypass pump tubing.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Cardiopulmonary bypass pump tubing. 870.4390... bypass pump tubing. (a) Identification. A cardiopulmonary bypass pump tubing is polymeric tubing which is... through the cardiopulmonary bypass circuit. (b) Classification. Class II (performance standards). ...

  18. Development, prevention, and treatment of feeding tube dependency

    NARCIS (Netherlands)

    Krom, Hilde; de Winter, J. Peter; Kindermann, Angelika

    2017-01-01

    Enteral nutrition is effective in ensuring nutritional requirements and growth. However, when tube feeding lasts for a longer period, it can lead to tube dependency in the absence of medical reasons for continuation of tube feeding. Tube-dependent children are unable or refuse to start oral

  19. Acoustic Resonance in Cylindrical Tubes with Side Branches

    Science.gov (United States)

    2013-05-01

    branches and tubes that change diameter. 4. Musical Instrument Design A flute is essentially a hollow tube with a way at one end to modulate the...an integer (1,2,3,…). 12 Figure 5. Tube with no holes. The addition of a side branch effectively changes the length of the tube, so in a flute

  20. Signal processing and display for electrochemical data

    Science.gov (United States)

    Young, R. N.; Wilkins, J. R.

    1977-01-01

    Two electrochemical electrodes provide signals; apparatus automatically determines reaction end point and displays lag period in time or cell concentration. Apparatus can be used with standard pH reference anode and platinum anode or with redox electrodes.

  1. High Resolution Autostereoscopic Cockpit Display Project

    Data.gov (United States)

    National Aeronautics and Space Administration — During this Phase II program Dimension Technologies Inc. (DTI) proposes to design and build an autostereoscopic (glasses-free 3D) LCD based aircraft cockpit display...

  2. Projection/Reflection Heads-up Display

    Data.gov (United States)

    National Aeronautics and Space Administration — To address the NASA need for an extravehicular activity (EVA) information display device, Physical Optics Corporation (POC) proposes to advance development of a new...

  3. Three D displays in military applications

    Science.gov (United States)

    Trakalo, M.

    2009-05-01

    The evolution to 3D content is considered to be the next quantum leap in the movie industry, and is currently taking place. The prospect of the home entertainment industry adopting 3D is causing display manufacturers to develop 3D compatible products. In the past, 3D displays have often been limited by poor image quality. The current generation of 3D displays can have image quality that approaches that of their 2D counterparts. 3D content has found its way to the cinema and is seeking a way into the home, but will it have a place in the military environment? This paper discusses the current status of 3D display technology and its suitability to the military ground mobile environment. It includes an introduction to 3D visualization and examines issues such as implementation, image quality, and human factors.

  4. Diagnosis of fault location using polygon displays.

    Science.gov (United States)

    Greaney, J; MacRae, A N

    1996-03-01

    When polygon displays are used to represent multiple sources of information, sometimes they can be processed in parallel so that the significant information can be taken in 'at a glance'. Previous studies found that reaction times (RTs) remained constant as the number of vertices was increased (Greaney and MacRae 1993). However, these studies did not call for the explicit identification of critical vertices and used polygons that were relatively regular. The present study required abnormal vertices to be identified, and it was found that RTs increased as a function of the total number of vertices. In addition, RTs were longer when the variability of the displayed information was greater, that is, when the polygon was more irregular. It was concluded that the polygon display may have more potential as a global warning indicator than as a means of displaying individual parameter values, which must be assessed separately.

  5. Compressive multi-mode superresolution display

    KAUST Repository

    Heide, Felix

    2014-01-01

    Compressive displays are an emerging technology exploring the co-design of new optical device configurations and compressive computation. Previously, research has shown how to improve the dynamic range of displays and facilitate high-quality light field or glasses-free 3D image synthesis. In this paper, we introduce a new multi-mode compressive display architecture that supports switching between 3D and high dynamic range (HDR) modes as well as a new super-resolution mode. The proposed hardware consists of readily-available components and is driven by a novel splitting algorithm that computes the pixel states from a target high-resolution image. In effect, the display pixels present a compressed representation of the target image that is perceived as a single, high resolution image. © 2014 Optical Society of America.

  6. Advanced Plasmonic Materials for Dynamic Color Display.

    Science.gov (United States)

    Shao, Lei; Zhuo, Xiaolu; Wang, Jianfang

    2017-11-10

    Plasmonic structures exhibit promising applications in high-resolution and durable color generation. Research on advanced hybrid plasmonic materials that allow dynamically reconfigurable color control has developed rapidly in recent years. Some of these results may give rise to practically applicable reflective displays in living colors with high performance and low power consumption. They will attract broad interest from display markets, compared with static plasmonic color printing, for example, in applications such as digital signage, full-color electronic paper, and electronic device screens. In this progress report, the most promising recent examples of utilizing advanced plasmonic materials for the realization of dynamic color display are highlighted and put into perspective. The performances, advantages, and disadvantages of different technologies are discussed, with emphasis placed on both the potential and possible limitations of various hybrid materials for dynamic plasmonic color display. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Bioadsorption strategies with yeast molecular display technology.

    Science.gov (United States)

    Shibasaki, Seiji; Ueda, Mitsuyoshi

    2014-01-01

    Molecular display techniques using microbial cell surfaces have been widely developed in the past twenty years, and are useful tools as whole cell catalysts for various applications such as bioconversion, bioremediation, biosensing, and the screening system of protein libraries. Furthermore, different types of microbial cells among eukaryotic and prokaryotic strains have been investigated for their use in surface display technologies. Recently, several kinds of protein-displaying yeasts have been utilized as bioadsorbents in this platform technology. In particular, these trials have successfully expanded the possibility of applications to metal binding, affinity purification, and receptor-ligand interaction by using the yeast cell surface. In this mini review, we describe the general principles of molecular display technology using yeast cells and its applications, with a particular focus on bioadsorption.

  8. Space Station Displays and Controls Technology Evolution

    Science.gov (United States)

    Blackburn, Greg C.

    1990-01-01

    Viewgraphs on space station displays and controls technology evolution are presented. Topics covered include: a historical perspective; major development objectives; current development activities; key technology areas; and technology evolution issues.

  9. General tube law for collapsible thin and thick-wall tubes.

    Science.gov (United States)

    Kozlovsky, Pavel; Zaretsky, Uri; Jaffa, Ariel J; Elad, David

    2014-07-18

    Modeling the complex deformations of cylindrical tubes under external pressure is of interest in engineering and physiological applications. The highly non-linear post-buckling behavior of cross-section of the tube during collapse attracted researchers for years. Major efforts were concentrated on studying the behavior of thin-wall tubes. Unfortunately, the knowledge on post-buckling of thick-wall tubes is still incomplete, although many experimental and several theoretical studies have been performed. In this study we systematically studied the effect of the wall thickness on post-buckling behavior of the tube. For this purpose, we utilized a computational model for evaluation of the real geometry of the deformed cross-sectional area due to negative transmural (internal minus external) pressure. We also developed an experimental method to validate the computational results. Based on the computed cross-sections of tubes with different wall thicknesses, we developed a general tube law that accounts for thin or thick wall tubes and fits the numerical data of computed cross-sectional areas versus transmural pressures. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Automated Determination of Oxygen-Dependent Enzyme Kinetics in a Tube-in-Tube Flow Reactor

    DEFF Research Database (Denmark)

    Ringborg, Rolf Hoffmeyer; Pedersen, Asbjørn Toftgaard; Woodley, John

    2017-01-01

    and limited oxygen supply. Here, we present a novel method for the collection of such kinetic data using a pressurized tube-in-tube reactor, operated in the low-dispersed flow regime to generate time-series data, with minimal material consumption. Experimental development and validation of the instrument...

  11. Fluid heating by current injection tubes; Chauffage de fluides par tubes a passage de courant

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, L.S. [Societe Parmilleux (France)

    1999-04-01

    Current injection tube technology may be applied in compact fluid heating installation with a very low level of thermal inertia. The technology is particularly suitable for heating heat-sensitive fluids or those with a tendency to foul other types of installations. Specific advantages of current injection tubes include the elimination of cold spots and their reduced volume requirements. (author)

  12. UNUSUAL SITE OF OBSTRUCTION IN A FLEXOMETALLIC TUBE

    Directory of Open Access Journals (Sweden)

    Habib Rahaman

    2014-12-01

    Full Text Available Maxillofacial procedure such as LeFort I osteotomy requires Transmyelohyoid Intubation. For that initial intubation is done with Flexometallic Endotracheal Tube so that this tube can be easily brought out through transmyelohyoid incision. Frequently Flexometallic tubes are reused after Ethylene Oxide Sterilisation because of high Cost. Here we present an obstruction to endotracheal tube at an unusual location, (Deformity of the tube at the level of Cuff, with intact cuff.

  13. Automated Diagnosis and Classification of Steam Generator Tube Defects

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Gabe V. Garcia

    2004-10-01

    A major cause of failure in nuclear steam generators is tube degradation. Tube defects are divided into seven categories, one of which is intergranular attack/stress corrosion cracking (IGA/SCC). Defects of this type usually begin on the outer surface of the tubes and propagate both inward and laterally. In many cases these defects occur at or near the tube support plates. Several different methods exist for the nondestructive evaluation of nuclear steam generator tubes for defect characterization.

  14. Exocyst SEC3 and Phosphoinositides Define Sites of Exocytosis in Pollen Tube Initiation and Growth.

    Science.gov (United States)

    Bloch, Daria; Pleskot, Roman; Pejchar, Přemysl; Potocký, Martin; Trpkošová, Pavlína; Cwiklik, Lukasz; Vukašinović, Nemanja; Sternberg, Hasana; Yalovsky, Shaul; Žárský, Viktor

    2016-10-01

    Polarized exocytosis is critical for pollen tube growth, but its localization and function are still under debate. The exocyst vesicle-tethering complex functions in polarized exocytosis. Here, we show that a sec3a exocyst subunit null mutant cannot be transmitted through the male gametophyte due to a defect in pollen tube growth. The green fluorescent protein (GFP)-SEC3a fusion protein is functional and accumulates at or proximal to the pollen tube tip plasma membrane. Partial complementation of sec3a resulted in the development of pollen with multiple tips, indicating that SEC3 is required to determine the site of pollen germination pore formation. Time-lapse imaging demonstrated that SEC3a and SEC8 were highly dynamic and that SEC3a localization on the apical plasma membrane predicts the direction of growth. At the tip, polar SEC3a domains coincided with cell wall deposition. Labeling of GFP-SEC3a-expressing pollen with the endocytic marker FM4-64 revealed the presence of subdomains on the apical membrane characterized by extensive exocytosis. In steady-state growing tobacco (Nicotiana tabacum) pollen tubes, SEC3a displayed amino-terminal Pleckstrin homology-like domain (SEC3a-N)-dependent subapical membrane localization. In agreement, SEC3a-N interacted with phosphoinositides in vitro and colocalized with a phosphatidylinositol 4,5-bisphosphate (PIP 2 ) marker in pollen tubes. Correspondingly, molecular dynamics simulations indicated that SEC3a-N associates with the membrane by interacting with PIP 2 However, the interaction with PIP 2 is not required for polar localization and the function of SEC3a in Arabidopsis (Arabidopsis thaliana). Taken together, our findings indicate that SEC3a is a critical determinant of polar exocytosis during tip growth and suggest differential regulation of the exocytotic machinery depending on pollen tube growth modes. © 2016 American Society of Plant Biologists. All Rights Reserved.

  15. Flash vacuum-ultraviolet generator having a mercury-anode tube

    Science.gov (United States)

    Sagae, Michiaki; Sato, Eiichi; Oizumi, Teiji; Yamamoto, Mariko; Takabe, Akihito; Sakamaki, Kimio; Ojima, Hidenori; Takayama, Kazuyoshi; Tamakawa, Yoshiharu; Yanagisawa, Toru

    1995-09-01

    The fundamental studies on a flash vacuum-ultraviolet (VUV) generator for producing water- window x rays are described. this generator consisted of the following essential components: a high-voltage power supply, a polarity-inversion-type high-voltage pulser having a 15 nF condenser, a thyristor pulser as a trigger device, a turbo molecular pump, and a VUV tube. The VUV tube employed a mercury anode, and the ferrite cathode was embedded in the anode. The pressure in the tube was primarily determined by the steam pressure of mercury as a function of temperature. The condenser in the pulser was charged from -10 to -30 kV by the power supply, and the electric charges in the condenser were discharged to the radiation tube after closing a gap switch by the thyristor pulser. As the high electron flows from the cathode electrode evaporated the anode electrode, VUV rays were then produced. The maximum output voltage from the pulser was approximately -1 times the charging voltage, and both the tube voltage and current displayed damped oscillations. The maximum values of the tube voltage and current were 14 kV and 2.0 kA, respectively. Since the effective accelerating voltage was substantially decreased by the ferrite cathode, soft x rays were easily generated. The pulse durations of the VUV rays including water-window x rays were nearly equivalent to those of the damped oscillations of the voltage and current, and their values were less than 15 microsecond(s) .

  16. Screen Codes: Visual Hyperlinks for Displays

    OpenAIRE

    Collomosse, J.; Kindberg, T.

    2008-01-01

    We present 'Screen codes' - a space- and time-efficient, aesthetically compelling method for transferring data from a display to a camera-equipped mobile device. Screen codes encode data as a grid of luminosity fluctuations within an arbitrary image, displayed on the video screen and decoded on a mobile device. These 'twinkling' images are a form of 'visual hyperlink', by which users can move dynamically generated content to and from their mobile devices. They help bridge the 'content divide'...

  17. Modern Display Technologies for Airborne Applications.

    Science.gov (United States)

    1983-04-01

    cover can be controlled as function * of the background luminance level ( photochromic , electrochromic materials). But at very low light levels, where...UUAUITY DISPLAY (DLA Umask (Aperture pitch *GRAPHIC DISPLAY ROUNDOAPERTURE (Sn 0 03ia02(m MASK AND 00 Biack matrix (S11) pigmented IRS Electron beam gun... soluble in the liquid crystal host to give adequate absorption and contrast without risk of the segregation of dye particles at low temperatures

  18. Bidding for Representative Allocations for Display Advertising

    OpenAIRE

    Ghosh, Arpita; McAfee, Preston; Papineni, Kishore; Vassilvitskii, Sergei

    2009-01-01

    Display advertising has traditionally been sold via guaranteed contracts -- a guaranteed contract is a deal between a publisher and an advertiser to allocate a certain number of impressions over a certain period, for a pre-specified price per impression. However, as spot markets for display ads, such as the RightMedia Exchange, have grown in prominence, the selection of advertisements to show on a given page is increasingly being chosen based on price, using an auction. As the number of parti...

  19. Online Allocation Rules in Display Advertising

    OpenAIRE

    Shamsi, Davood; Holtan, Marius; Luenberger, Robert; Ye, Yinyu

    2014-01-01

    Efficient allocation of impressions to advertisers in display advertising has a significant impact on advertisers' utility and the browsing experience of users. The problem becomes particularly challenging in the presence of advertisers with limited budgets as this creates a complex interaction among advertisers in the optimal impression assignment. In this paper, we study online impression allocation in display advertising with budgeted advertisers. That is, upon arrival of each impression, ...

  20. Managing Risk of Bidding in Display Advertising

    OpenAIRE

    Zhang, HaiFeng; Zhang, Weinan; Rong, Yifei; Ren, Kan; Li, Wenxin; Wang, Jun

    2017-01-01

    In this paper, we deal with the uncertainty of bidding for display advertising. Similar to the financial market trading, real-time bidding (RTB) based display advertising employs an auction mechanism to automate the impression level media buying; and running a campaign is no different than an investment of acquiring new customers in return for obtaining additional converted sales. Thus, how to optimally bid on an ad impression to drive the profit and return-on-investment becomes essential. Ho...

  1. Oil defect detection of electrowetting display

    Science.gov (United States)

    Chiang, Hou-Chi; Tsai, Yu-Hsiang; Yan, Yung-Jhe; Huang, Ting-Wei; Mang, Ou-Yang

    2015-08-01

    In recent years, transparent display is an emerging topic in display technologies. Apply in many fields just like mobile device, shopping or advertising window, and etc. Electrowetting Display (EWD) is one kind of potential transparent display technology advantages of high transmittance, fast response time, high contrast and rich color with pigment based oil system. In mass production process of Electrowetting Display, oil defects should be found by Automated Optical Inspection (AOI) detection system. It is useful in determination of panel defects for quality control. According to the research of our group, we proposed a mechanism of AOI detection system detecting the different kinds of oil defects. This mechanism can detect different kinds of oil defect caused by oil overflow or material deteriorated after oil coating or driving. We had experiment our mechanism with a 6-inch Electrowetting Display panel from ITRI, using an Epson V750 scanner with 1200 dpi resolution. Two AOI algorithms were developed, which were high speed method and high precision method. In high precision method, oil jumping or non-recovered can be detected successfully. This mechanism of AOI detection system can be used to evaluate the oil uniformity in EWD panel process. In the future, our AOI detection system can be used in quality control of panel manufacturing for mass production.

  2. A new type of multiview display

    Science.gov (United States)

    Jurk, Silvio; Kuhlmey, Mathias; de la Barré, René

    2015-03-01

    The common architecture of multi-view autostereoscopic displays assigns a nominal viewing distance. The design affects the convergence of the visible rays at a nominal viewing distance where diamond shaped viewing zones are created. In contrast to this approach, the authors present a new design strategy departing from the geometric relations of common 3D display designs. They show that a beam emitted from a sub-pixel should be rendered with an individual camera direction determined by an algorithm. This algorithm also uses, besides the parameters of the display design, the desired viewing distance and the allowed increments of the camera angle. This enables very flexible designs of autostereoscopic displays. The main difference from the common multiview display is that its design approach enables a continued viewing zone without the usually diamond shaped sweet spots. The algorithm for controlling the rendering and the multiplexing is generic, as well as for integral and multiview design approaches using an image splitter raster. The paper introduces it for autostereoscopic displays with horizontal parallax.

  3. SES cupola interactive display design environment

    Science.gov (United States)

    Vu, Bang Q.; Kirkhoff, Kevin R.

    1989-01-01

    The Systems Engineering Simulator, located at the Lyndon B. Johnson Space Center in Houston, Texas, is tasked with providing a real-time simulator for developing displays and controls targeted for the Space Station Freedom. These displays and controls will exist inside an enclosed workstation located on the space station. The simulation is currently providing the engineering analysis environment for NASA and contractor personnel to design, prototype, and test alternatives for graphical presentation of data to an astronaut while he performs specified tasks. A highly desirable aspect of this environment is to have the capability to rapidly develop and bring on-line a number of different displays for use in determining the best utilization of graphics techniques in achieving maximum efficiency of the test subject fulfilling his task. The Systems Engineering Simulator now has available a tool which assists in the rapid development of displays for these graphic workstations. The Display Builder was developed in-house to provide an environment which allows easy construction and modification of displays within minutes of receiving requirements for specific tests.

  4. Display of information in the operating room.

    Science.gov (United States)

    Kiefer, Nicholas; Hoeft, Andreas

    2010-12-01

    The ongoing development of new sensors and parameters for intraoperative monitoring has outpaced the development of display design, leading to a gap between the load of information and the quality of its delivery. This is not a circumstantial problem, as a large portion of critical incidents is attributable to inadequate situation awareness and the failure to recognize readily monitored data. This review also addresses improvements of current threshold alarms. Research has focused on advanced integrated displays, drawing on the findings of human factor science and on the exploitation of alternative sensory pathways. Integrated displays, as well as auditory, vibrotactile and head-mounted displays have been shown to promote situation awareness and reduce cognitive workload. Intelligent alarm design can successfully reduce the number of false alarms. Improvement of the display of information in the operating room is warranted, and recent developments are promising. However, their introduction into mass market is not yet on the horizon, although the shortcomings of the traditional single-sensor-single-indicator principle are known for a long time. If manufacturers are reluctant to implement new techniques into their devices, they should at least facilitate access to monitoring raw data in order to allow independent development of displays.

  5. HDTV and large-screen display

    Science.gov (United States)

    Mitsuhashi, Tetsuo

    1990-08-01

    HDTV (known as Hi-Vision in Japan), with its ability to provide through high- definition pictures on a large screen display advanced psychological effects such as sensations of reality and a visual impact unobtainable in conventional television, is the television system of the next generation. In Japan, daily one-hour experimental broadcasting was initiated in June 1989 using the BS-2 broadcast satellite, and regular service is scheduled to begin via the BS-3 satellite to be launched in 1990. To this end, a home-use receiver using VLSIs has already been developed. Moreover, HDTV is currently being applied in such diverse areas as film production, printing and publishing, medicine, and art museums. The HDTV system handles approximately five times the information of conventional television. As a result, a large screen display capable of maintaining stable resolution greater than twice that of conventional displays is essential to the full realization of HDTV's vast potential. This paper will first discuss HDTV's basic parameters, concentrating on the psychovisual effects, and explain some preferable display characteristics from this psychovisual point of view. It will then discuss the technical problems in developing such a display, and final ly describe the current state of HDTV display development.

  6. Folate receptors and neural tube closure.

    Science.gov (United States)

    Saitsu, Hirotomo

    2017-09-01

    Neural tube defects (NTD) are among the most common human congenital malformations, affecting 0.5-8.0/1000 of live births. Human clinical trials have shown that periconceptional folate supplementation significantly decreases the occurrence of NTD in offspring. However, the mechanism by which folate acts on NTD remains largely unknown. Folate receptor (Folr) is one of the three membrane proteins that mediate cellular uptake of folates. Recent studies suggest that mouse Folr1 (formerly referred to as Fbp1) is essential for neural tube closure. Therefore, we examined spatial and temporal expression patterns of Folr1 in developing mouse embryos, showing a close association between Folr1 and anterior neural tube closure. Transient transgenic analysis was performed using lacZ as a reporter; we identified a 1.1-kb enhancer that directs lacZ expression in the neural tube and optic vesicle in a manner that is similar to endogenous Folr1. The 1.1-kb enhancer sequences were highly conserved between humans and mice, suggesting that human FOLR1 is associated with anterior neural tube closure in humans. Several experimental studies in mice and human epidemiological and genetics studies have suggested that folate receptor abnormalities are involved in a portion of human NTDs, although the solo defect of FOLR1 did not cause NTD. © 2017 Japanese Teratology Society.

  7. Geiger-Muller tubes and their manufacture

    Energy Technology Data Exchange (ETDEWEB)

    Gair, S.A.; Copleston, R.E.

    1991-02-06

    A Geiger-Muller tube designed for use in an environment subjected to mechanical shock and vibration has a tensioned anode wire secured between first and second mounts located at opposite ends of the tube envelope. The wire tension is adjusted, preferably with a screwable-adjustment means which is locked in the adjusted position, so that the natural frequency of vibration of the tensioned wire does not resonate with any frequency to which the tube is subjected in use. The adjustment means may be included in the mount via which the envelope is evacuated and back-filled with the ionizable gas, and a gas-tight seal can be provided around this part of the mount for example by sealing off the gas pump tube. However the adjustment means may be designed into another part of the tube, for example using telescopic parts of the envelope whose sliding junction is made gas tight with a flexible seal. Alternatively, the desired tension may be obtained by welding the wire to the first mount, passing it through the second mount, tensioning it and then crimping it to the second mount. (Author).

  8. Administration of antiretroviral medication via enteral tubes.

    Science.gov (United States)

    Prohaska, Emily S; King, Allison R

    2012-12-15

    Case reports and other published or manufacturer-provided data on the administration of antiretroviral agents through enteral feeding tubes are reviewed. There is very limited published evidence to guide clinicians in the delivery of therapies for human immunodeficiency virus (HIV) infection by feeding tubes, especially crushed tablets and capsule contents. A search of the primary literature (through February 2012) identified a total of nine articles describing the delivery of highly active antiretroviral therapy (HAART) agents via gastrostomy (G), jejunostomy, and other feeding tubes; correspondence with pharmaceutical manufacturers yielded additional information. Most of the published evidence (from two prospective studies, one retrospective study, and six case reports) pertains to the treatment of HIV-infected children (33 of 40 cases). Although not a primary endpoint of any of the reviewed studies, viral suppression was documented in 29 of the 40 patients referenced in the reviewed articles. Manufacturer-provided information indicates that crushed darunavir tablets in suspension, as well as oral solutions of ritonavir and lopinavir-ritonavir, can be administered through G-tubes without significant loss of therapeutic efficacy. Data regarding enteral feeding tube administration are available for 63% of commercially available oral HAART agents and are primarily limited to case reports specific to the pediatric population.

  9. Jejunostomy tube feeding in patients undergoing esophagectomy.

    Science.gov (United States)

    Srinathan, Sadeesh K; Hamin, Tamara; Walter, Stephen; Tan, A Lawrence; Unruh, Helmut W; Guyatt, Gordon

    2013-12-01

    Surgical jejunostomy tubes are a routine part of elective esophagectomies in patients with carcinomas and provide a route for nutritional support in those who experience complications. We wished to determine how frequently oral intake is delayed and the amount of nutrition delivered via the jejunostomy tube. We reviewed the charts of all adults undergoing esophagectomy for carcinoma between January 2000 and June 2008. We determined the proportion of patients unable to resume oral nutrition after 8 days and the amount of nutrition delivered in each of the 8 days. In all, 111 patients underwent elective esophagectomy for carcinoma, and 103 had a jejunostomy tube placed. The mean age was 67 ± 10.8 years. The median time to oral intake was 7 (interquartile range 7-11) days. Seventy-four (67%) patients resumed oral intake within 8 days. The mean nutrition delivered by jejunostomy within the first 8 days as a percentage of the target was 45.6% (95% confidence interval 41.2%-49.9%). Six (5.4%) patients experienced complications attributable solely to the jejunostomy tube; 3 (2.9%) required surgery. Forty (38.8%) patients had abdominal issues serious enough to warrant delaying the progression of feeding. Two-thirds of patients undergoing elective esophagectomy were tolerating oral intake by the end of the eighth postoperative day, and less than half of the target nutrition was delivered over the first 8 days. We now selectively place surgical jejunostomy tubes in patients undergoing elective esophagectomies.

  10. Design and evaluate finned tube bundles

    Energy Technology Data Exchange (ETDEWEB)

    Ganapathy, V. [ABCO Industries, Abilene, TX (United States)

    1996-09-01

    Finned tube bundles are widely used in heat exchangers, air coolers, waste heat boilers and fired heaters where energy transfer occurs between clean flue gases and a fluid with a high heat-transfer coefficient. They have several advantages including compactness, low gas pressure drop and low weight for a given duty compared to bare tube bundles. Choosing a fin type, arrangement and fin configuration requires a thorough analysis and economic evaluation. The solution is not unique since it depends on material and labor costs. Surface areas vary widely in finned tube designs for the same duty and gas pressure drop. Therefore, decisions should not be based on surface area alone. Plant engineers and consultants should consider operating costs in their evaluation because they accrue year after year. Selecting a boiler based on initial costs alone is not prudent. The paper discusses heat transfer and gas pressure drop with finned tubes, determining fin efficiency and effectiveness,g as pressure drop, tube wall and fin top temperatures, an example calculation, the effect of fin configuration on design, the effect of inline versus staggered arrangements and solid versus serrated fins, and concerns with high fin-density designs.

  11. Construction of preheaters with horizontal tubes

    Energy Technology Data Exchange (ETDEWEB)

    Goetze

    1944-09-27

    This report involved construction of preheaters for distillation and cracking plants in the oil industry, particularly in America. The use of heat transmission by radiation was also a consideration here. The recycling of waste gases occurred, but was not the rule. A convection section was often built next to the radiation section, in which the discharge gases were used for heating the incoming product. The general arrangement of the preheaters was discussed. The first form was a rectangular box with fireproof lining with tubes arranged in a single row along the outer walls and sometimes in a double row on the ceiling. It consisted of smooth and finned tubes. From the simple form a double preheater was developed that allowed one or two common discharge flues to provide as large a heating surface as possible within a reasonable space. Other items discussed were recycling of waste gases, reasons for the choice of horizontal preheaters with radiation heating, the use of vertical tubes in the U.S.A. and elsewhere in the oil industry, details of horizontal preheater tubes, end closures, material, suspension, protection against overloading by radiation, circulation heating, burners, use of horizontal radiation preheaters in hydrogenation in the U.S.A., rebuilding I. G. preheaters, construction, tube supports, and masonry. A list of references on cracking, preheaters, heat transmission, and alloyed steels was given.

  12. Mechanical properties of ceramic composite tubes

    Energy Technology Data Exchange (ETDEWEB)

    Curtin, W.A.; Oleksuk, L.L.; Reifsnider, K.L. [Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (United States); Stinton, D.P. [Oak Ridge National Lab., TN (United States)

    1995-08-01

    Results of axial tension tests on SiC/SiC tubular ceramic composite components fabricated by a forced-M technique are presented. Axial elastic modulus measurements on a number of tubes show that the Young`s modulus varies along the length of the tube, with occasional very stiff or very soft regions. Tests to failure on a few tubes show the initiation of non-linear stress-strain behavior to be in the range of 3-9 ksi, followed by extensive non-linear deformation up to failure. For one tube, the failure stress obtained was 20.1 ksi, but the strains to failure at various axial locations varies from 0.19%to 0.24%. The correlation between modulus and proportional limit is considered within the ACK matrix cracking theory and within a model in which matrix cracking between fiber tows occurs, both modified to account for matrix porosity. The crack size required to cause stress concentrations large enough to cause failure at the observed strength is considered. Predictions for both matrix cracking and strength suggest that the current generation of tubes are controlled by microstructural defects.

  13. Air liquide's space pulse tube cryocooler systems

    Science.gov (United States)

    Trollier, T.; Tanchon, J.; Buquet, J.; Ravex, A.

    2017-11-01

    Thanks to important development efforts completed with ESA funding, Air Liquide Advanced Technology Division (AL/DTA), is now in position to propose two Pulse Tube cooler systems in the 40-80K temperature range for coming Earth Observation missions such as Meteosat Third Generation (MTG), SIFTI, etc… The Miniature Pulse Tube Cooler (MPTC) is lifting up to 2.47W@80K with 50W compressor input power and 10°C rejection temperature. The weight is 2.8 kg. The Large Pulse Tube Cooler (LPTC) is providing 2.3W@50K for 160W input power and 10°C rejection temperature. This product is weighing 5.1 kg. The two pulse tube coolers thermo-mechanical units are qualified against environmental constraints as per ECSS-E-30. They are both using dual opposed pistons flexure bearing compressor with moving magnet linear motors in order to ensure very high lifetime. The associated Cooler Drive Electronics is also an important aspect specifically regarding the active control of the cooler thermo-mechanical unit during the launch phase and the active reduction of the vibrations induced by the compressor (partly supported by the French Agency CNES). This paper details the presentation of the two Pulse Tube Coolers together with the Cooler Drive Electronics aspects.

  14. Detailed Root Cause Analysis of SG Tube ODSCC Indications within the Tube Sheets of NPP Biblis Unit A

    Science.gov (United States)

    Kilian, R.; Beck, J.; Lang, H.; Schönherr, T.; Widera, M.

    Biblis Unit A is a Siemens/KWU type four loop PWR equipped with SG tubing made from Stainless Steel Alloy 800, operating from 1975 until the shutdown in 2011 due to the German political decision of a quick nuclear phase out. During the regular SG tubing inspections using eddy current testing in 2005 and 2006, a few SG tube indications were detected within the tube sheet between upper and lower mechanical tube expansion. These indications were limited to the outer tube bundle periphery. As a consequence two tubes with EC indications were pulled in 2006 for further investigations. The destructive examinations revealed axially oriented cracks starting from the outer tube surface (ODSCC). The analysis of the debris from the upper expansion area clearly indicated the presence of secondary side water in the volume between tube sheet and SG tube. Penetration of secondary side water is only possible by a penetration path along the upper expansion.

  15. Evolution Of Map Display Optical Systems

    Science.gov (United States)

    Boot, Alan

    1983-06-01

    It is now over 20 years since Ferranti plc introduced optically projected map displays into operational aircraft navigation systems. Then, as now, it was the function of the display to present an image of a topographical map to a pilot or navigator with his present position clearly identified. Then, as now, the map image was projected from a reduced image stored on colour micro film. Then, as now, the fundamental design problems are the same.In the exposed environment of an aircraft cockpit where brightness levels may vary from those associated with direct sunlight on the one hand, to starlight on the other, how does one design an optical system with sufficient luminance, contrast and resolution where in the daytime sunlight may fall on the display or in the pilot's eyes, and at night time the display luminance must not detract from the pilot's ability to pick up external clues? This paper traces the development of Ferranti plc optically projected map displays from the early V Bomber and the ill-fated TSR2 displays to the Harrier and Concorde displays. It then goes on to the development of combined map and electronic displays (COMED), showing how an earlier design, as fitted to Tornado, has been developed into the current COMED design which is fitted to the F-18 and Jaguar aircraft. In each of the above display systems particular features of optical design interest are identified and their impact on the design as a whole are discussed. The use of prisms both for optical rotation and translation, techniques for the maximisation of luminance, the problems associated with contrast enhancement, particularly with polarising filters in the presence of optically active materials, the use of aerial image combining systems and the impact of the pilot interface on the system parameter are all included.Perhaps the most interesting result in considering the evolution of map displays has not been so much the designer's solutions in overcoming the various design problems but

  16. Characterizing the reflectivity of handheld display devices.

    Science.gov (United States)

    Liu, Peter; Badano, Aldo

    2014-08-01

    With increased use of handheld and tablet display devices for viewing medical images, methods for consistently measuring reflectivity of the devices are needed. In this note, the authors report on the characterization of diffuse reflections for handheld display devices including mobile phones and tablets using methods recommended by the American Association of Physicists in Medicine Task Group 18 (TG18). The authors modified the diffuse reflectance coefficient measurement method outlined in the TG18 report. The authors measured seven handheld display devices (two phones and five tablets) and three workstation displays. The device was attached to a black panel with Velcro. To study the effect of the back surface on the diffuse reflectance coefficient, the authors created Styrofoam masks with different size square openings and placed it in front of the device. Overall, for each display device, measurements of illuminance and reflected luminance on the display screen were taken. The authors measured with no mask, with masks of varying size, and with display-size masks, and calculated the corresponding diffuse reflectance coefficient. For all handhelds, the diffuse reflectance coefficient measured with no back panel were lower than measurements performed with a mask. The authors found an overall increase in reflectivity as the size of the mask decreases. For workstations displays, diffuse reflectance coefficients were higher when no back panel was used, and higher than with masks. In all cases, as luminance increased, illuminance increased, but not at the same rate. Since the size of handheld displays is smaller than that of workstation devices, the TG18 method suffers from a dependency on illumination condition. The authors show that the diffuse reflection coefficients can vary depending on the nature of the back surface of the illuminating box. The variability in the diffuse coefficient can be as large as 20% depending on the size of the mask. For all measurements

  17. Direct ophthalmoscopy on YouTube

    DEFF Research Database (Denmark)

    Borgersen, Nanna Jo; Henriksen, Mikael Johannes Vuokko; Konge, Lars

    2016-01-01

    BACKGROUND: Direct ophthalmoscopy is well-suited for video-based instruction, particularly if the videos enable the student to see what the examiner sees when performing direct ophthalmoscopy. We evaluated the pedagogical effectiveness of instructional YouTube videos on direct ophthalmoscopy...... in general. We then systematically searched YouTube. Two authors reviewed eligible videos to assess eligibility and extract data on video statistics, content, and approach to visualization. Correlations between video statistics and contents were investigated using two-tailed Spearman's correlation. RESULTS...... the patient and how to examine the fundus. Time spent on fundus examination correlated with the number of views per week (Spearman's ρ=0.53; P=0.029). CONCLUSION: Videos may help overcome the pedagogical issues in teaching direct ophthalmoscopy; however, the few available videos on YouTube fail to address...

  18. Circumferential cracking of steam generator tubes

    Energy Technology Data Exchange (ETDEWEB)

    Karwoski, K.J.

    1997-04-01

    On April 28, 1995, the U.S. Nuclear Regulatory Commission (NRC) issued Generic Letter (GL) 95-03, {open_quote}Circumferential Cracking of Steam Generator Tubes.{close_quote} GL 95-03 was issued to obtain information needed to verify licensee compliance with existing regulatory requirements regarding the integrity of steam generator tubes in domestic pressurized-water reactors (PWRs). This report briefly describes the design and function of domestic steam generators and summarizes the staff`s assessment of the responses to GL 95-03. The report concludes with several observations related to steam generator operating experience. This report is intended to be representative of significant operating experience pertaining to circumferential cracking of steam generator tubes from April 1995 through December 1996. Operating experience prior to April 1995 is discussed throughout the report, as necessary, for completeness.

  19. Pneumatosis intestinalis associated with enteral tube feeding.

    Science.gov (United States)

    Zorgdrager, Marcel; Pol, Robert

    2013-12-03

    A 49-year-old man presented with a Hinchey II perforated diverticulitis and underwent laparoscopic peritoneal lavage. During the postoperative course the patient received enteral tube feeding which was followed by a bowel obstruction accompanied with pneumatosis intestinalis (PI). Explorative laparotomy showed an omental band adhesion without signs of ischaemia. After a short period of total parenteral nutrition PI resolved almost completely and enteral tube feeding could be continued once again. In the weeks that followed the patient developed atypical bowel symptoms and recurrent PI which resolved each time the drip feeding was discontinued. Despite the mild clinical course, a CT scan showed massive PI on day 21 after the laparotomy. After excluding life-threatening conditions conservative management was instituted and the patient recovered completely after discontinuing the drip feeding. We present one of the few cases of subclinical PI associated with enteral tube feeding that could be managed conservatively.

  20. Plasmonic band structures in doped graphene tubes.

    Science.gov (United States)

    Zhou, Yu; Zhu, Ying-Ying; Zhang, Kun; Wu, Hong-Wei; Peng, Ru-Wen; Fan, Ren-Hao; Wang, Mu

    2017-05-29

    We present theoretically the transport of plasmonic waves in doped graphene tube, which is made by rolling planar graphene sheet into a cylinder and periodic doping is applied on it. It is shown that periodic modulation of the Fermi level along the tube can open gaps in the dispersion relations of graphene plasmons and eventually create plasmonic band structures. The propagation of graphene plasmons is forbidden within the bandgaps; while within the band, the plasmonic waves present axially-extended field distributions and propagate along the tubes, yet well confined around the curved graphene surface. Furthermore, the bandgaps, propagation constants and propagation lengths of the modes in plasmonic band structures are significantly tuned by varying the Fermi level of graphene, which provides active controls over the plasmonic waves. Our proposed structures here may provide an approach to dynamically control the plasmonic waves in graphene-based subwavelength waveguides.

  1. Monocular display unit for 3D display with correct depth perception

    Science.gov (United States)

    Sakamoto, Kunio; Hosomi, Takashi

    2009-11-01

    A study of virtual-reality system has been popular and its technology has been applied to medical engineering, educational engineering, a CAD/CAM system and so on. The 3D imaging display system has two types in the presentation method; one is a 3-D display system using a special glasses and the other is the monitor system requiring no special glasses. A liquid crystal display (LCD) recently comes into common use. It is possible for this display unit to provide the same size of displaying area as the image screen on the panel. A display system requiring no special glasses is useful for a 3D TV monitor, but this system has demerit such that the size of a monitor restricts the visual field for displaying images. Thus the conventional display can show only one screen, but it is impossible to enlarge the size of a screen, for example twice. To enlarge the display area, the authors have developed an enlarging method of display area using a mirror. Our extension method enables the observers to show the virtual image plane and to enlarge a screen area twice. In the developed display unit, we made use of an image separating technique using polarized glasses, a parallax barrier or a lenticular lens screen for 3D imaging. The mirror can generate the virtual image plane and it enlarges a screen area twice. Meanwhile the 3D display system using special glasses can also display virtual images over a wide area. In this paper, we present a monocular 3D vision system with accommodation mechanism, which is useful function for perceiving depth.

  2. Tactile display with dielectric multilayer elastomer actuatorsq

    Science.gov (United States)

    Matysek, Marc; Lotz, Peter; Schlaak, Helmut F.

    2009-03-01

    Tactile perception is the human sensation of surface textures through the vibrations generated by stroking a finger over the surface. The skin responds to several distributed physical quantities. Perhaps the most important are high-frequency vibrations, pressure distributions (static shape) and thermal properties. The integration of tactile displays in man-machine interfaces promises a more intuitive handling. For this reason many tactile displays are developed using different technologies. We present several state-of-the-art tactile displays based on different types of dielectric elastomer actuators to clarify the advantages of our matrix display based on multilayer technology. Using this technology perpendicular and hexagonal arrays of actuator elements (tactile stimulators) can be integrated into a PDMS substrate. Element diameters down to 1 mm allow stimuli at the range of the human two-point-discrimination threshold. Driving the elements by column and row addressing enables various stimulation patterns with a reduced number of feeding lines. The transient analysis determines charging times of the capacitive actuators depending on actuator geometry and material parameters. This is very important to ensure an adequate dynamic characteristic of the actuators to stimulate the human skin by vibrations. The suitability of multilayer dielectric elastomer actuators for actuation in tactile displays has been determined. Beside the realization of a static tactile display - where multilayer DEA are integrated as drives for movable contact pins - we focus on the direct use of DEA as a vibrotactile display. Finally, we present the scenario and achieved results of a recognition threshold test. Even relative low voltages in the range of 800 V generate vibrations with 100% recognition ratio within the group of participants. Furthermore, the frequency dependent characteristic of the determined recognition threshold confirms with established literature.

  3. 21-in. technology-independent common display set (CLADS) design for rugged workstation applications

    Science.gov (United States)

    Gorenflo, Ronald L.; Hermann, David J.

    1997-07-01

    Battelle is under contract with Warner Robins Air Logistics Center to design a Common Large Area Display Set (CLADS) for use in multiple command, control, communications, computers, and intelligence applications that currently use 19-inch cathode ray tubes (CRTs). Battelle engineers have now demonstrated that the modular CLADS design is applicable to a large number of existing and future rugged workstation applications, and that the design is technology independent. Any display technology that can be packaged to meet the form, fit, and function requirements defined by the common large area display head assembly performance specification is a candidate for CLADS applications. This has already reduced the risk of CLADS development, permits life long technology insertion upgrades without unnecessary redesign, and addresses many of the obsolescence problems associated with COTS technology-based acquisition. For each platform, only the unique form and fit requirements are included in a CLADS application integration kit, while the unique functional interfaces are provided by an application video interface module. All other parts of the design are common to all CLADS installations and are therefore required in higher quantities which means lower costs. A performance specification tree lists the specifications for each of the platforms as well as the specifications for the modules used for each platform. Detailed specifications have been drafted and will be released to potential display integrators and manufacturers for review in the coming weeks. Initial USAF applications include replacements for the E-3 AWACS color monitor assembly, E-8 Joint STARS graphics display unit, and ABCCC airborne color display. Initial US Navy applications include the E-2C ACIS display. For these applications, reliability and maintainability are key objectives. The common design will reduce the cost of operation and maintenance by an estimated 3.3 million dollars per year on E-3 AWACS alone. As

  4. Flat-panel electronic displays: a triumph of physics, chemistry and engineering.

    Science.gov (United States)

    Hilsum, Cyril

    2010-03-13

    This paper describes the history and science behind the development of modern flat-panel displays, and assesses future trends. Electronic displays are an important feature of modern life. For many years the cathode ray tube, an engineering marvel, was universal, but its shape was cumbersome and its operating voltage too high. The need for a flat-panel display, working at a low voltage, became imperative, and much research has been applied to this need. Any versatile flat-panel display will exploit an electro-optical effect, a transparent conductor and an addressing system to deliver data locally. The first need is to convert an electrical signal into a visible change. Two methods are available, the first giving emission of light, the second modulating ambient illumination. The most useful light-emitting media are semiconductors, historically exploiting III-V or II-VI compounds, but more recently organic or polymer semiconductors. Another possible effect uses gas plasma discharges. The modulating, or subtractive, effects that have been studied include liquid crystals, electrophoresis, electrowetting and electrochromism. A transparent conductor makes it possible to apply a voltage to an extended area while observing the results. The design is a compromise, since the free electrons that carry current also absorb light. The first materials used were metals, but some semiconductors, when heavily doped, give a better balance, with high transmission for a low resistance. Delivering data unambiguously to a million or so picture elements across the display area is no easy task. The preferred solution is an amorphous silicon thin-film transistor deposited at each cross-point in an X-Y matrix. Success in these endeavours has led to many applications for flat-panel displays, including television, flexible displays, electronic paper, electronic books and advertising signs.

  5. Digital Radiography Qualification of Tube Welding

    Science.gov (United States)

    Carl, Chad

    2012-01-01

    The Orion Project will be directing Lockheed Martin to perform orbital arc welding on commodities metallic tubing as part of the Multi Purpose Crew Vehicle assembly and integration process in the Operations and Checkout High bay at Kennedy Space Center. The current method of nondestructive evaluation is utilizing traditional film based x-rays. Due to the high number of welds that are necessary to join the commodities tubing (approx 470), a more efficient and expeditious method of nondestructive evaluation is desired. Digital radiography will be qualified as part of a broader NNWG project scope.

  6. Energy absorption of braided composite tubes

    Science.gov (United States)

    Beard, Shawn Joseph

    In this investigation, a model was developed for simulating the crushing behavior and predicting the energy absorption characteristics of braided composite tubes. The crushing model uses the finite element code ABAQUS along with a material module that describes the constitutive behavior of the braid material. The material module contains a three-dimensional description of the braid geometry, which is used to calculate the effective stiffnesses of a representative volume. The stiffness calculations include the effects of nonlinear shear, damage accumulation, and scissoring and jamming of the braider tows. A stiffness reduction scheme, based on the predicted failure mode, is used to account for tow and resin failure throughout the representative volume. Scissoring of the braider tows results in an increase in the overall effective compliance until jamming occurs. To facilitate the model development, extensive coupon tests and tube crushing experiments were conducted. Coupon tests were conducted on braided flat plaques to help characterize the damage mechanisms occurring and to obtain the initial stiffnesses for verifying the proposed model. The braided flat plaques were made using 80k Akzo Nobel Fortafil carbon fiber tows for both the axial and braider tows, and Hetron 922 epoxy-vinyl ester resin for the matrix. Crushing tests were conducted on braided carbon fiber/epoxy-vinyl ester composite tubes with both circular and square cross-sections. All tests were conducted quasi-statically, and plug-type initiators were used to trigger the progressive crushing. The braided tubes were made using 80k Akzo Nobel Fortafil carbon fiber tows for the axial tows, 12k Hercules Grafil 34-700 carbon fiber tows for the braider tows, and Hetron 922 epoxy-vinyl ester resin for the matrix. The energy absorption characteristics are significantly affected by the fiber architecture of the tube and the fillet radius of the initiator plug. In order to verify the proposed model, simulation

  7. Pulse tube coolers for Meteosat third generation

    Science.gov (United States)

    Butterworth, James; Aigouy, Gérald; Chassaing, Clement; Debray, Benoît; Huguet, Alexandre

    2014-01-01

    Air Liquide's Large Pulse Tube Coolers (LPTC) will be used to cool the focal planes of the Infrared Sounder (IRS) and Flexible Combined Imager (FCI) instruments aboard the ESA/Eumetsat satellites Meteosat Third Generation (MTG). This cooler consists of an opposed piston linear compressor driving a pulse tube cold head and the associated drive electronics including temperature regulation and vibration cancellation algorithms. Preparations for flight qualification of the cooler are now underway. In this paper we present results of the optimization and qualification activities as well as an update on endurance testing.

  8. Arrested Bubble Rise in a Narrow Tube

    Science.gov (United States)

    Lamstaes, Catherine; Eggers, Jens

    2017-05-01

    If a long air bubble is placed inside a vertical tube closed at the top it can rise by displacing the fluid above it. However, Bretherton found that if the tube radius, R, is smaller than a critical value Rc=0.918 ℓ _c, where ℓ _c=√{γ /ρ g} is the capillary length, there is no solution corresponding to steady rise. Experimentally, the bubble rise appears to have stopped altogether. Here we explain this observation by studying the unsteady bubble motion for Rmotion.

  9. Nitrous oxide use and endotracheal tube rupture.

    Science.gov (United States)

    Mosby, E L; Schelkun, P M; Vincent, S K

    1988-01-01

    Nitrous oxide is an important and widely used anesthetic agent. However, during lengthy surgical procedures, significant amounts of nitrous oxide diffuse into the endotracheal tube cuff, causing sequelae that may include increased cuff pressures, tracheal trauma, increased postoperative discomfort, and cuff rupture. In this paper, two cases are presented in which the endotracheal tube cuff used to deliver this anesthetic agent ruptured after more than four hours of surgery. Two simple means of limiting the diffusion of nitrous oxide into the cuff and thus preventing this occurrence are described.

  10. Self-assembling segmented coiled tubing

    Energy Technology Data Exchange (ETDEWEB)

    Raymond, David W.

    2016-09-27

    Self-assembling segmented coiled tubing is a concept that allows the strength of thick-wall rigid pipe, and the flexibility of thin-wall tubing, to be realized in a single design. The primary use is for a drillstring tubular, but it has potential for other applications requiring transmission of mechanical loads (forces and torques) through an initially coiled tubular. The concept uses a spring-loaded spherical `ball-and-socket` type joint to interconnect two or more short, rigid segments of pipe. Use of an optional snap ring allows the joint to be permanently made, in a `self-assembling` manner.

  11. Unique system of photoreceptors in sea urchin tube feet.

    Science.gov (United States)

    Ullrich-Lüter, Esther M; Dupont, Sam; Arboleda, Enrique; Hausen, Harald; Arnone, Maria Ina

    2011-05-17

    Different sea urchin species show a vast variety of responses to variations in light intensity; however, despite this behavioral evidence for photosensitivity, light sensing in these animals has remained an enigma. Genome information of the recently sequenced purple sea urchin (Strongylocentrotus purpuratus) allowed us to address this question from a previously unexplored molecular perspective by localizing expression of the rhabdomeric opsin Sp-opsin4 and Sp-pax6, two genes essential for photoreceptor function and development, respectively. Using a specifically designed antibody against Sp-Opsin4 and in situ hybridization for both genes, we detected expression in two distinct groups of photoreceptor cells (PRCs) located in the animal's numerous tube feet. Specific reactivity of the Sp-Opsin4 antibody with sea star optic cushions, which regulate phototaxis, suggests a similar visual function in sea urchins. Ultrastructural characterization of the sea urchin PRCs revealed them to be of a microvillar receptor type. Our data suggest that echinoderms, in contrast to chordates, deploy a microvillar, r-opsin-expressing PRC type for vision, a feature that has been so far documented only in protostome animals. Surprisingly, sea urchin PRCs lack any associated screening pigment. Indeed, one of the tube foot PRC clusters may account for directional vision by being shaded through the opaque calcite skeleton. The PRC axons connect to the animal internal nervous system, suggesting an integrative function beyond local short circuits. Because juveniles display no phototaxis until skeleton completion, we suggest a model in which the entire sea urchin, deploying its skeleton as PRC screening device, functions as a huge compound eye.

  12. Communicating creativity on YouTube: what and for whom?

    Science.gov (United States)

    Courtois, Cédric; Mechant, Peter; Marez, Lieven De

    2012-03-01

    This article addresses nonprofessional users' expressions of everyday creativity on YouTube, adopting the idea that making entails connecting on different levels. By combining different materials and ideas into a video and sharing it within the social context of the platform, uploaders can connect with its enormous audience. In our first study, we explore patterns in the elements that are used when creating a video. We also question whether these pattern combinations are aimed at different types of viewers. Our results show that videos with self-made content that display various skills are mainly targeted at viewers situated close to the uploader (e.g., family, friends). However, videos that incorporate instances of popular culture, either as a whole (e.g., a pop concert recording) or in part (e.g., remixed with other content), are directed at a much broader audience. In our second study, we question whether these self-made videos convey a message about uploaders' personality traits commonly linked to creative behavior. We found that independent observers are able to accurately predict the uploaders' actual openness to experience, a trait marked as the substrate of creativity. Next, we discuss our results in light of a pessimistic view of today's democratized culture. We show that uploaders appear to have a tacit knowledge of what kind of videos are interesting for what type of viewers. We conclude that, despite the lowered barriers to the production and dissemination of video, YouTube viewers are still able to identify variations in the personality trait most commonly associated to creativity.

  13. A sinuous tumulus over an active lava tube at Kīlauea Volcano: Evolution, analogs, and hazard forecasts

    Science.gov (United States)

    Orr, Tim R.; Bleacher, Jacob E.; Patrick, Matthew R.; Wooten, Kelly M.

    2015-01-01

    Inflation of narrow tube-fed basaltic lava flows (tens of meters across), such as those confined by topography, can be focused predominantly along the roof of a lava tube. This can lead to the development of an unusually long tumulus, its shape matching the sinuosity of the underlying lava tube. Such a situation occurred during Kīlauea Volcano's (Hawai'i, USA) ongoing East Rift Zone eruption on a lava tube active from July through November 2010. Short-lived breakouts from the tube buried the flanks of the sinuous, ridge-like tumulus, while the tumulus crest, its surface composed of lava formed very early in the flow's emplacement history, remained poised above the surrounding younger flows. At least several of these breakouts resulted in irrecoverable uplift of the tube roof. Confined sections of the prehistoric Carrizozo and McCartys flows (New Mexico, USA) display similar sinuous, ridge-like features with comparable surface age relationships. We contend that these distinct features formed in a fashion equivalent to that of the sinuous tumulus that formed at Kīlauea in 2010. Moreover, these sinuous tumuli may be analogs for some sinuous ridges evident in orbital images of the Tharsis volcanic province on Mars. The short-lived breakouts from the sinuous tumulus at Kīlauea were caused by surges in discharge through the lava tube, in response to cycles of deflation and inflation (DI events) at Kīlauea's summit. The correlation between DI events and subsequent breakouts aided in lava flow forecasting. Breakouts from the sinuous tumulus advanced repeatedly toward the sparsely populated Kalapana Gardens subdivision, destroying two homes and threatening others. Hazard assessments, including flow occurrence and advance forecasts, were relayed regularly to the Hawai'i County Civil Defense to aid their lava flow hazard mitigation efforts while this lava tube was active.

  14. A sinuous tumulus over an active lava tube at Kīlauea Volcano: evolution, analogs, and hazard forecasts

    Science.gov (United States)

    Orr, Tim R.; Bleacher, Jacob E.; Patrick, Matthew R.; Wooten, Kelly M.

    2015-01-01

    Inflation of narrow tube-fed basaltic lava flows (tens of meters across), such as those confined by topography, can be focused predominantly along the roof of a lava tube. This can lead to the development of an unusually long tumulus, its shape matching the sinuosity of the underlying lava tube. Such a situation occurred during Kīlauea Volcano's (Hawai'i, USA) ongoing East Rift Zone eruption on a lava tube active from July through November 2010. Short-lived breakouts from the tube buried the flanks of the sinuous, ridge-like tumulus, while the tumulus crest, its surface composed of lava formed very early in the flow's emplacement history, remained poised above the surrounding younger flows. At least several of these breakouts resulted in irrecoverable uplift of the tube roof. Confined sections of the prehistoric Carrizozo and McCartys flows (New Mexico, USA) display similar sinuous, ridge-like features with comparable surface age relationships. We contend that these distinct features formed in a fashion equivalent to that of the sinuous tumulus that formed at Kīlauea in 2010. Moreover, these sinuous tumuli may be analogs for some sinuous ridges evident in orbital images of the Tharsis volcanic province on Mars. The short-lived breakouts from the sinuous tumulus at Kīlauea were caused by surges in discharge through the lava tube, in response to cycles of deflation and inflation (DI events) at Kīlauea's summit. The correlation between DI events and subsequent breakouts aided in lava flow forecasting. Breakouts from the sinuous tumulus advanced repeatedly toward the sparsely populated Kalapana Gardens subdivision, destroying two homes and threatening others. Hazard assessments, including flow occurrence and advance forecasts, were relayed regularly to the Hawai'i County Civil Defense to aid their lava flow hazard mitigation efforts while this lava tube was active.

  15. Geology of selected lava tubes in the Bend Area, Oregon

    Science.gov (United States)

    Greely, R.

    1971-01-01

    Longitudinal profiles representing 5872.5 m of mapped lava tubes and a photogeologic map relating lava tubes to surface geology, regional structure and topography are presented. Three sets of lava tubes were examined: (1) Arnold Lava Tube System (7km long) composed of collapsed and uncollapsed tube segments and lava ponds, (2) Horse Lava Tube System (11 km long) composed of parallel and anastomosing lava tube segments, and (3) miscellaneous lava tubes. Results of this study tend to confirm the layered lava hypothesis of Ollier and Brown (1965) for lava tube formation; however, there are probably several modes of formation for lava tubes in general. Arnold System is a single series of tubes apparently formed in a single basalt flow on a relatively steep gradient. The advancing flow in which the tubes formed was apparently temporarily halted, resulting in the formation of lava ponds which were inflated and later drained by the lava tube system. Horse System probably formed in multiple, interconnected flows. Pre-flow gradient appears to have been less than for Arnold System, and resulted in meandrous, multiple tube networks.

  16. Everything the nurse practitioner should know about pediatric feeding tubes.

    Science.gov (United States)

    Hannah, Erin; John, Rita Marie

    2013-11-01

    To provide an overview of the current feeding tubes in use in the pediatric population including feeding tube complications, and specific guidance for patients at the initiation, throughout the use of, and at the discontinuation of tube feeding. A review of the literature was performed using multiple databases including PubMed, CINAHL, Ovid Medline, and Cochrane Library. Key words used included pediatric gastrostomy (G) tubes, nasogastric (NG) tubes, gastrojejunostomy (GJ) tubes, enteral access, and nurse practitioner (NP). Any child who cannot obtain nutrition orally is a candidate for enteral feeding tube access. Tube feeding is the recommended care guideline for children that are undernourished or unable to safely take-in oral nutrition. Tube feeding has been known to improve health-related quality of life. There are a number of different forms of feeding tubes that can be used in children, including NG, orogastric, G, and GJ tubes. Children are being sent home regularly with enteral feeding tube access and NPs will encounter these patients in everyday practice. It is important that NPs know the risks and benefits of tube feeding as well as the types of tubes currently in use and their indications, advantages, disadvantages, and complications. ©2013 The Author(s) ©2013 American Association of Nurse Practitioners.

  17. MEMS tactile display: from fabrication to characterization

    Science.gov (United States)

    Miki, Norihisa; Kosemura, Yumi; Watanabe, Junpei; Ishikawa, Hiroaki

    2014-03-01

    We report fabrication and characterization of MEMS-based tactile display that can display users various tactile information, such as Braille codes and surface textures. The display consists of 9 micro-actuators that are equipped with hydraulic displacement amplification mechanism (HDAM) to achieve large enough displacement to stimulate the human tactile receptors. HDAM encapsulates incompressible liquids. We developed a liquid encapsulation process, which we termed as Bonding-in-Liquid Technique, where bonding with a UV-curable resin in glycerin is conducted in the liquid, which prevented interfusion of air bubbles and deformation of the membrane during the bonding. HDAM successfully amplified the displacement generated by piezoelectric actuators by a factor of 6. The display could virtually produce "rough" and "smooth" surfaces, by controlling the vibration frequency, displacement, and the actuation periods of an actuator until the adjacent actuator was driven. We introduced a sample comparison method to characterize the surfaces, which involves human tactile sensation. First, we prepared samples whose mechanical properties are known. We displayed a surface texture to the user by controlling the parameters and then, the user selects a sample that has the most similar surface texture. By doing so, we can correlate the parameters with the mechanical properties of the sample as well as find the sets of the parameters that can provide similar tactile information to many users. The preliminary results with respect to roughness and hardness is presented.

  18. Imaging display method for airborne oceanographic LIDAR

    Science.gov (United States)

    Davis, Jon P.; Keck, Timothy; Umehara, Michael J.

    1990-09-01

    Typical airborne Light Detection and Ranging (LIDAR) used for oceanographic measurements collect data at rates in the range of 1 Megabyte per second. This paper presents a method for organizing and displaying this great bulk of data to allow screening for areas of interest. In addition, this method can be transferred to dedicated hardware, to provide a 100% real time data display system at a reasonable cost. A typical airborne LIDAR system contains a scanning transceiver, and digitizes returned waveforms as the aircraft ffies some search pattern. Thus the data is inherently four dimensional (intensity and three spatial dimensions). This method reliesupon collapsing the four dimensional data into three dimensions; color and X,Y screen coordinates. This is doneby translating depth into an RGB color mix, and return intensity into RGB intensity. Thus color represents depth, and brightness represents signal strength. This data is then displayed on a high resolution color display. In order for this to be successful, some preprocessing is necessary to normalize the waveforms, so that changes in the displayreflect changes in the water column. In addition, some digital filtering is beneficial to increase the signal to noise ratio. This system is currentlyimplemented in Greenhills 'C' under CLIX (UnixVport toClipper) running on a Zaiaz 933 compute engine, with RASIL graphics software package on a Zaiaz FB 640 Graphics frame buffer. This hardware provides 5 MIPS average execution rate and 16.7 million colors on a 768 x 576 pixel display.

  19. Wave function properties of a single and a system of magnetic flux tube(s) oscillations

    Science.gov (United States)

    Esmaeili, Shahriar; Nasiri, Mojtaba; Dadashi, Neda; Safari, Hossein

    2016-10-01

    In this study, the properties of wave functions of the MHD oscillations for a single and a system of straight flux tubes are investigated. Magnetic flux tubes with a straight magnetic field and longitudinal density stratification were considered in zero-β approximation. A single three-dimensional wave equation (eigenvalue problem) is solved for longitudinal component of the perturbed magnetic field using the finite element method. Wave functions (eigenfunction of wave equation) of the MHD oscillations are categorized into sausage, kink, helical kink, and fluting modes. Exact recognition of the wave functions and the frequencies of oscillations can be used in coronal seismology and also helps to the future high-resolution instruments that would be designed for studying the properties of the solar loop oscillations in details. The properties of collective oscillations of nonidentical and identical system of flux tubes and their interactions are studied. The ratios of frequencies, the oscillation frequencies of a system of flux tubes to their equivalent monolithic tube (ω sys/ω mono), are obtained between 0.748 and 0.841 for a system of nonidentical tubes, whereas the related ratios of frequencies for a system of identical flux tubes are fluctuated around 0.761.

  20. Influence of tube spinning on formability of friction stir welded aluminum alloy tubes for hydroforming application

    Energy Technology Data Exchange (ETDEWEB)

    Wang, X.S. [State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Hu, Z.L., E-mail: zhilihuhit@163.com [State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Hubei Key Laboratory of Advanced Technology of Automobile Parts, Wuhan University of Technology, Wuhan 430070 (China); State Key Laboratory of Materials Processing and Die and Mould Technology, Huazhong University of Science and Technology (China); Yuan, S.J. [State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Hua, L. [Hubei Key Laboratory of Advanced Technology of Automobile Parts, Wuhan University of Technology, Wuhan 430070 (China)

    2014-06-01

    Due to economic and ecological reasons, the application of tailor-welded blanks of aluminum alloy has gained more and more attention in manufacturing lightweight structures for automotives and aircrafts. In the study, the research was aimed to highlight the influence of spinning on the formability of FSW tubes. The microstructural characteristics of the FSW tubes during spinning were studied by electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM). The formability of the FSW tubes with different spinning reduction was assessed by hydraulic bulge test. It is found that the spinning process shows a grain refinement of the tube. The grains of the FSW tube decrease with increasing thickness reduction, and the effect of grain refinement is more obvious for the BM compared to that of the weld. The difference of grain size and precipitates between the weld and BM leads to an asymmetric W-type microhardness distribution after spinning. The higher thickness reduction of the tube, the more uniform distribution of grains and precipitates it shows, and consequently results in more significant increase of strength. As compared with the result of tensile test, the tube after spinning shows better formability when the stress state changes from uniaxial to biaxial stress state.

  1. Performance of pressure tubes in CANDU reactors

    Energy Technology Data Exchange (ETDEWEB)

    Rodgers, D.; Griffiths, M.; Bickel, G.; Buyers, A.; Coleman, C.; Nordin, H.; St Lawrence, S. [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada)

    2016-06-15

    The pressure tubes in CANDU reactors typically operate for times up to about 30 years prior to refurbishment. The in-reactor performance of Zr-2.5Nb pressure tubes has been evaluated by sampling and periodic inspection. This paper describes the behavior and discusses the factors controlling the behaviour of these components. The Zr–2.5Nb pressure tubes are nominally extruded at 815{sup o}C, cold worked nominally 27%, and stress relieved at 400 {sup o}C for 24 hours, resulting in a structure consisting of elongated grains of hexagonal close-packed alpha-Zr, partially surrounded by a thin network of filaments of body-centred-cubic beta-Zr. These beta-Zr filaments are meta-stable and contain about 20% Nb after extrusion. The stress-relief treatment results in partial decomposition of the beta-Zr filaments with the formation of hexagonal close-packed alpha-phase particles that are low in Nb, surrounded by a Nb-enriched beta-Zr matrix. The material properties of pressure tubes are determined by variations in alpha-phase texture, alpha-phase grain structure, network dislocation density, beta-phase decomposition, and impurity concentration that are a function of manufacturing variables. The pressure tubes operate at temperatures between 250 {sup o}C and 310 {sup o}C with coolant pressures up to about 11 MPa in fast neutron fluxes up to 4 x 10{sup 17} n·m{sup -2}·s{sup -1} (E > 1 MeV) and the properties are modified by these conditions. The properties of the pressure tubes in an operating reactor are therefore a function of both manufacturing and operating condition variables. The ultimate tensile strength, fracture toughness, and delayed hydride-cracking properties (velocity (V) and threshold stress intensity factor (K{sub IH})) change with irradiation, but all reach a nearly limiting value at a fluence of less than 10{sup 25} n·m{sup -2} (E > 1 MeV). At this point the ultimate tensile strength is raised about 200 MPa, toughness is reduced by about 50%, V increases

  2. YouTube as an information source for pediatric adenotonsillectomy and ear tube surgery.

    Science.gov (United States)

    Sorensen, Jeffrey A; Pusz, Max D; Brietzke, Scott E

    2014-01-01

    Assess the overall quality of information on adenotonsillectomy and ear tube surgery presented on YouTube (www.youtube.com) from the perspective of a parent or patient searching for information on surgery. The YouTube website was systematically searched on select dates with a formal search strategy to identify videos pertaining to pediatric adenotonsillectomy and ear tube surgery. Only videos with at least 5 (ear tube surgery) or 10 (adenotonsillectomy) views per day were included. Each video was viewed and scored by two independent scorers. Videos were categorized by goal and scored for video/audio quality, accuracy, comprehensiveness, and procedure-specific content. Cross-sectional study. Public domain website. Fifty-five videos were scored for adenotonsillectomy and forty-seven for ear tube surgery. The most common category was educational (65.3%) followed by testimonial (28.4%), and news program (9.8%). Testimonials were more common for adenotonsillectomy than ear tube surgery (41.8% vs. 12.8%, p=0.001). Testimonials had a significantly lower mean accuracy (2.23 vs. 2.62, p=0.02), comprehensiveness (1.71 vs. 2.22, p=0.007), and TA specific content (0.64 vs. 1.69, p=0.001) score than educational type videos. Only six videos (5.9%) received high scores in both video/audio quality and accuracy/comprehensiveness of content. There was no significant association between the accuracy and comprehensive score and views, posted "likes", posted "dislikes", and likes/dislikes ratio. There was an association between "likes" and mean video quality (Spearman's rho=0.262, p=0.008). Parents/patients searching YouTube for information on pediatric adenotonsillectomy and ear tube surgery will generally encounter low quality information with testimonials being common but of significantly lower quality. Viewer perceived quality ("likes") did not correlate to formally scored content quality. Published by Elsevier Ireland Ltd.

  3. Display interface concepts for automated fault diagnosis

    Science.gov (United States)

    Palmer, Michael T.

    1989-01-01

    An effort which investigated concepts for displaying dynamic system status and fault history (propagation) information to the flight crew is described. This investigation was performed by developing several candidate display formats and then conducting comprehension tests to determine those characteristics that made one format preferable to another for presenting this type of information. Twelve subjects participated. Flash tests, or limited time exposure tests, were used to determine the subjects' comprehension of the information presented in the display formats. It was concluded from the results of the comprehension tests that pictographs were more comprehensible than both block diagrams and text for presenting dynamic system status and fault history information, and that pictographs were preferred over both block diagrams and text. It was also concluded that the addition of this type of information in the cockpit would help the crew remain aware of the status of their aircraft.

  4. Interacting on and around Large Displays

    DEFF Research Database (Denmark)

    Markussen, Anders

    Over the past two decades, interactions on and around large high-resolution displays have gained increasing levels of attention in research and in practice. This thesis explores and compares interaction techniques for large displays that operate up-close and at a distance. More specifically......, the focus of this thesis is on three aspects of large display interactions: (1) Improved Mid-Air Text Entry; (2) Improved Understanding of Input Modalities; and (3) Extended Boundaries of Interaction. To improve support for mid-air text entry, Paper 1 conducted a design space analysis, and three mid...... for text entry. However, future work could potentially increase text entry rates of the mid-air keyboard by studying and identifying the specific properties that resulted in the performance benefits of the touch-based keyboard. Paper 3 also proposed the Back Of the Hand (BOH) as a novel interaction...

  5. Display design strategy for condition monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Paulsen, Jette Lundtang

    2002-08-15

    This report describes the development of a strategy for interface design for process plants. The strategy is based on methods from risk analysis to elicit the problems in the plant. In the present work the strategy has been used on a condenser and a high pressure preheater. The test of the strategy in this work focuses on the condition of systems, but could as well focus on functions of the plant. The report further describes from which sources knowledge about the plant can be extracted. A display for supervision of the condenser condition has been tested on a nuclear power plant, a gas fired power plant and the HAMBO simulator(HAMlab BOiling water reactor). A pre-heater display is still under development, but has been tested on a PC display, replaying data collected at the HAMBO simulator. (Author)

  6. Druid, event display for the linear collider

    CERN Document Server

    Ruan, M; Musat, G; Jeans, D; Pande, J

    2013-01-01

    Druid is a dedicated event display designed for the future e +e − linear colliders. Druid takes standard linear collider data files and detector geometry description files as input, it can visualize both physics event and detector geometry. Many displaying options are provided by Druid, giving easy access to different information. As a versatile event display, Druid supports all the latest linear collider detector models, Silicon Detector and International Large Detector, as well as the calorimeter prototypes operated in the CALICE test beam experiments. It has been utilized in many studies such as the verification of detector geometry, analysis of the simulated full events and test beam data as well as reconstruction algorithm development and code debugging.

  7. Characterising laser beams with liquid crystal displays

    Science.gov (United States)

    Dudley, Angela; Naidoo, Darryl; Forbes, Andrew

    2016-02-01

    We show how one can determine the various properties of light, from the modal content of laser beams to decoding the information stored in optical fields carrying orbital angular momentum, by performing a modal decomposition. Although the modal decomposition of light has been known for a long time, applied mostly to pattern recognition, we illustrate how this technique can be implemented with the use of liquid-crystal displays. We show experimentally how liquid crystal displays can be used to infer the intensity, phase, wavefront, Poynting vector, and orbital angular momentum density of unknown optical fields. This measurement technique makes use of a single spatial light modulator (liquid crystal display), a Fourier transforming lens and detector (CCD or photo-diode). Such a diagnostic tool is extremely relevant to the real-time analysis of solid-state and fibre laser systems as well as mode division multiplexing as an emerging technology in optical communication.

  8. Speckle suppression in scanning laser display.

    Science.gov (United States)

    Yurlov, Victor; Lapchuk, Anatoly; Yun, Sangkyeong; Song, Jonghyeong; Yang, Haengseok

    2008-01-10

    The theory of speckle noise in a scanning beam is presented. The general formulas for the calculation of speckle contrast, which apply to any scanning display, are obtained. It is shown that the main requirement for successful speckle suppression in a scanning display is a narrow autocorrelation peak and low sidelobe level in the autocorrelation function of the complex amplitude distribution across a scanning light beam. The simple formulas for speckle contrast for a beam with a narrow autocorrelation function peak were obtained. It was shown that application of a diffractive optical element (DOE) with a Barker code phase shape could use only natural display scanning motion for speckle suppression. DOE with a Barker code phase shape has a small size and may be deposited on the light modulator inside the depth of the focus of the reflected beam area, and therefore, it does not need an additional image plane and complicated relay optics.

  9. High performance visual display for HENP detectors

    CERN Document Server

    McGuigan, M; Spiletic, J; Fine, V; Nevski, P

    2001-01-01

    A high end visual display for High Energy Nuclear Physics (HENP) detectors is necessary because of the sheer size and complexity of the detector. For BNL this display will be of special interest because of STAR and ATLAS. To load, rotate, query, and debug simulation code with a modern detector simply takes too long even on a powerful work station. To visualize the HENP detectors with maximal performance we have developed software with the following characteristics. We develop a visual display of HENP detectors on BNL multiprocessor visualization server at multiple level of detail. We work with general and generic detector framework consistent with ROOT, GAUDI etc, to avoid conflicting with the many graphic development groups associated with specific detectors like STAR and ATLAS. We develop advanced OpenGL features such as transparency and polarized stereoscopy. We enable collaborative viewing of detector and events by directly running the analysis in BNL stereoscopic theatre. We construct enhanced interactiv...

  10. WISP information display system user's manual

    Science.gov (United States)

    Alley, P. L.; Smith, G. R.

    1978-01-01

    The wind shears program (WISP) supports the collection of data on magnetic tape for permanent storage or analysis. The document structure provides: (1) the hardware and software configuration required to execute the WISP system and start up procedure from a power down condition; (2) data collection task, calculations performed on the incoming data, and a description of the magnetic tape format; (3) the data display task and examples of displays obtained from execution of the real time simulation program; and (4) the raw data dump task and examples of operator actions required to obtained the desired format. The procedures outlines herein will allow continuous data collection at the expense of real time visual displays.

  11. Software Verification of Orion Cockpit Displays

    Science.gov (United States)

    Biswas, M. A. Rafe; Garcia, Samuel; Prado, Matthew; Hossain, Sadad; Souris, Matthew; Morin, Lee

    2017-01-01

    NASA's latest spacecraft Orion is in the development process of taking humans deeper into space. Orion is equipped with three main displays to monitor and control the spacecraft. To ensure the software behind the glass displays operates without faults, rigorous testing is needed. To conduct such testing, the Rapid Prototyping Lab at NASA's Johnson Space Center along with the University of Texas at Tyler employed a software verification tool, EggPlant Functional by TestPlant. It is an image based test automation tool that allows users to create scripts to verify the functionality within a program. A set of edge key framework and Common EggPlant Functions were developed to enable creation of scripts in an efficient fashion. This framework standardized the way to code and to simulate user inputs in the verification process. Moreover, the Common EggPlant Functions can be used repeatedly in verification of different displays.

  12. Keratinocyte specific markers isolated using phage display

    DEFF Research Database (Denmark)

    Jensen, K.B.; Jensen, Ole Nørregaard; Ravn, P.

    2003-01-01

    Specific molecular markers for various normal and pathogenic cell states and cell types provide knowledge of basic biological systems and have a direct application in targeted therapy. We describe a proteomic method based on the combination of new and improved phage display antibody technologies...... display method was applied to analysis of human skin keratinocytes resulting in the isolation of a panel of antibodies. Fourteen of these antibodies were further characterized, half of which predominantly recognized keratinocytes in a screen of a range of different cell types. Three cognate keratinocyte...... antigens were subsequently identified by mass spectrometry as laminin-5, plectin, and fibronectin. The combination of phage display technology with mass spectrometry methods for protein identification is a general and promising approach for proteomic analysis of cell surface complexity....

  13. Pilot Preferences on Displayed Aircraft Control Variables

    Science.gov (United States)

    Trujillo, Anna C.; Gregory, Irene M.

    2013-01-01

    The experiments described here explored how pilots want available maneuver authority information transmitted and how this information affects pilots before and after an aircraft failure. The aircraft dynamic variables relative to flight performance were narrowed to energy management variables. A survey was conducted to determine what these variables should be. Survey results indicated that bank angle, vertical velocity, and airspeed were the preferred variables. Based on this, two displays were designed to inform the pilot of available maneuver envelope expressed as bank angle, vertical velocity, and airspeed. These displays were used in an experiment involving control surface failures. Results indicate the displayed limitations in bank angle, vertical velocity, and airspeed were helpful to the pilots during aircraft surface failures. However, the additional information did lead to a slight increase in workload, a small decrease in perceived aircraft flying qualities, and no effect on aircraft situation awareness.

  14. An Exact Hot-Tube Solution For Thin Tape Helix Traveling-Wave Tube

    Science.gov (United States)

    Wong, Patrick; Lau, Y. Y.; Gilgenbach, Ronald; Chernin, David; Hoff, Brad

    2017-10-01

    The exact hot-tube dispersion relation for a thin tape helix traveling-wave tube (TWT) is derived for the first time, based on its exact cold-tube solution. This is an attempt to provide a reliable determination of the Pierce parameters, in particular the ``AC space-charge'' parameter QC, for a realistic TWT. The determination of QC remains an outstanding issue. The numerical results from the exact formulation will be compared with other approximate models of TWT that were commonly used in the literature for QC. This work was supported by AFOSR Grant No. FA9550-15-1-0097.

  15. Microbial Contamination of Orthodontic Buccal Tubes from Manufacturers

    Directory of Open Access Journals (Sweden)

    Kok-Gan Chan

    2010-09-01

    Full Text Available This study aimed to test the sterility of new unused orthodontic buccal tubes received from manufacturers. Four different types of buccal tubes were used straight from the manufactures package without any additional sterilizing step. Of these buccal tubes tested, three genera of bacteria, implicated as opportunistic pathogens, namely Micrococcus luteus, Staphylococcus haemolyticus and Acinetobacter calcoaceticus were recovered from these buccal tubes. Our data showing microbial contamination on buccal tubes highlights the need of sterilization before clinical use. We also suggest that manufacturers should list the sterility state of orthodontic buccal tubes on their packaging or instructions stating the need for sterilization.

  16. Contrastive Analysis and Research on Negative Pressure Beam Tube System and Positive Pressure Beam Tube System for Mine Use

    Science.gov (United States)

    Wang, Xinyi; Shen, Jialong; Liu, Xinbo

    2018-01-01

    Against the technical defects of universally applicable beam tube monitoring system at present, such as air suction in the beam tube, line clogging, long sampling time, etc., the paper analyzes the current situation of the spontaneous combustion fire disaster forecast of mine in our country and these defects one by one. On this basis, the paper proposes a research thought that improving the positive pressure beam tube so as to substitute the negative pressure beam tube. Then, the paper introduces the beam tube monitoring system based on positive pressure technology through theoretical analysis and experiment. In the comparison with negative pressure beam tube, the paper concludes the advantage of the new system and draws the conclusion that the positive pressure beam tube is superior to the negative pressure beam tube system both in test result and test time. At last, the paper proposes prospect of the beam tube monitoring system based on positive pressure technology.

  17. Predicted Weather Display and Decision Support Interface for Flight Deck

    Science.gov (United States)

    Johnson, Walter W. (Inventor); Wong, Dominic G. (Inventor); Wu, Shu-Chieh (Inventor); Koteskey, Robert W. (Inventor)

    2017-01-01

    A system and method for providing visual depictions of a predictive weather forecast for in-route vehicle trajectory planning. The method includes displaying weather information on a graphical display, displaying vehicle position information on the graphical display, selecting a predictive interval, displaying predictive weather information for the predictive interval on the graphical display, and displaying predictive vehicle position information for the predictive interval on the graphical display, such that the predictive vehicle position information is displayed relative to the predictive weather information, for in-route trajectory planning.

  18. Liquid Oscillations in a U-Tube

    Science.gov (United States)

    Aguilar, Horacio Munguía; Maldonado, Rigoberto Franco; Navarro, Luis Barba

    2018-01-01

    In hydrostatics, pressure measurement with U-gauges and their relationship to density is a well-known experiment. Very little is studied or experimented with the dynamics of the movement of a liquid in a U-tube probably due to its theoretical complexity but, after all, it is a simple damped oscillating system. In this paper we present a relatively…

  19. "Fine grain Nb tube for SRF cavities"

    Energy Technology Data Exchange (ETDEWEB)

    Robert E. Barber

    2012-07-08

    Superconducting radio frequency (SRF) cavities used in charged particle linear accelerators, are currently fabricated by deep drawing niobium sheets and welding the drawn dishes together. The Nb sheet has a non-uniform microstructure, which leads to unpredictable cavity shape and surface roughness, and inconsistent "spring-back" during forming. In addition, weld zones cause hot spots during cavity operation. These factors limit linear accelerator performance and increase cavity manufacturing cost. Equal channel angular extrusion (ECAE) can be used to refine and homogenize the microstructure of Nb tube for subsequent hydroforming into SRF cavities. Careful selection of deformation and heat treatment conditions during the processing steps can give a uniform and consistent microstructure in the tube, leading to improved deformability and lower manufacturing costs. Favorable microstructures were achieved in short test samples of RRR Nb tube, which may be particularly suitable for hydroforming into SRF cavity strings. The approach demonstrated could be applicable to microstructure engineering of other tube materials including tantalum, titanium, and zirconium.

  20. Of Slot Machines and Broken Test Tubes

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 19; Issue 5. Of Slot Machines and Broken Test Tubes. S Mahadevan. General Article Volume 19 Issue 5 May 2014 pp 395-405. Fulltext. Click here to view fulltext PDF. Permanent link: http://www.ias.ac.in/article/fulltext/reso/019/05/0395-0405. Keywords.

  1. The LI-rings in pollen tubes

    Directory of Open Access Journals (Sweden)

    H. Q. Zhang

    2014-01-01

    Full Text Available Monoclonal antibodies, which recognize the specific epitopes for pectins and arabinogalactan proteins, in connection with confocal laser scanning microscopy demonstrated the presence of a ring-like structure in the cell wall of pollen tubes of flowering plants.

  2. Cotton transformation via pollen tube pathway.

    Science.gov (United States)

    Wang, Min; Zhang, Baohong; Wang, Qinglian

    2013-01-01

    Although many gene transfer methods have been employed for successfully obtaining transgenic cotton, the major constraint in cotton improvement is the limitation of genotype because the majority of transgenic methods require plant regeneration from a single transformed cell which is limited by cotton tissue culture. Comparing with other plant species, it is difficult to induce plant regeneration from cotton; currently, only a limited number of cotton cultivars can be cultured for obtaining regenerated plants. Thus, development of a simple and genotype-independent genetic transformation method is particularly important for cotton community. In this chapter, we present a simple, cost-efficient, and genotype-independent cotton transformation method-pollen tube pathway-mediated transformation. This method uses pollen tube pathway to deliver transgene into cotton embryo sacs and then insert foreign genes into cotton genome. There are three major steps for pollen tube pathway-mediated genetic transformation, which include injection of -foreign genes into pollen tube, integration of foreign genes into plant genome, and selection of transgenic plants.

  3. YouTube in the Science Classroom

    Science.gov (United States)

    Everhart, Jerry

    2009-01-01

    YouTube makes it possible for teachers to capitalize on children's insatiable appetite for visually stimulating learning. Some of these videos attain "viral" status, getting passed on from person to person and by links on other sites. Not only are these popular videos viral, but developing one's own content and posting it for the world's access is…

  4. YouTube: Educational Potentials and Pitfalls

    Science.gov (United States)

    Jones, Troy; Cuthrell, Kristen

    2011-01-01

    The instructional potential of video technology in the classroom is promising, especially in light of the 21st Century Learning Framework (Siegle, 2009). Studies show positive gains in student outcomes as a result of the integration of video technology in instruction. This article explores potential uses of YouTube as an instructional aid in…

  5. YouTube as a Participatory Culture

    Science.gov (United States)

    Chau, Clement

    2010-01-01

    There is an explosion of youth subscriptions to original content-media-sharing Web sites such as YouTube. These Web sites combine media production and distribution with social networking features, making them an ideal place to create, connect, collaborate, and circulate. By encouraging youth to become media creators and social networkers, new…

  6. Steam generator tube integrity flaw acceptance criteria

    Energy Technology Data Exchange (ETDEWEB)

    Cochet, B. [FRAMATOME, Paris la Defense (France)

    1997-02-01

    The author discusses the establishment of a flaw acceptance criteria with respect to flaws in steam generator tubing. The problem is complicated because different countries take different approaches to the problem. The objectives in general are grouped in three broad areas: to avoid the unscheduled shutdown of the reactor during normal operation; to avoid tube bursts; to avoid excessive leak rates in the event of an accidental overpressure event. For each degradation mechanism in the tubes it is necessary to know answers to an array of questions, including: how well does NDT testing perform against this problem; how rapidly does such degradation develop; how well is this degradation mechanism understood. Based on the above information it is then possible to come up with a policy to look at flaw acceptance. Part of this criteria is a schedule for the frequency of in-service inspection and also a policy for when to plug flawed tubes. The author goes into a broad discussion of each of these points in his paper.

  7. Indications and Complications of Tube Thoracostomy with ...

    African Journals Online (AJOL)

    patients were followed up with serial chest X‑rays until certified cured. ... 1‑80 years. The most frequent indication was for malignant/ paramalignant effusion, 46 (27.5%). Others were trauma,. 44 (26.3%), Parapneumonic effusion, 20 (12%), postthoracotomy ... X-rays until certified cured before removal of the chest tube.

  8. Aspergillus DNA contamination in blood collection tubes.

    Science.gov (United States)

    Harrison, Elizabeth; Stalhberger, Thomas; Whelan, Ruth; Sugrue, Michele; Wingard, John R; Alexander, Barbara D; Follett, Sarah A; Bowyer, Paul; Denning, David W

    2010-08-01

    Fungal polymerase chain reaction (PCR)-based diagnostic methods are at risk for contamination. Sample collection containers were investigated for fungal DNA contamination using real-time PCR assays. Up to 18% of blood collection tubes were contaminated with fungal DNA, probably Aspergillus fumigatus. Lower proportions of contamination in other vessels were observed. Copyright 2010 Elsevier Inc. All rights reserved.

  9. Aspergillus DNA contamination in blood collection tubes

    OpenAIRE

    Harrison, Elizabeth; Stahlberger, Thomas; Whelan, Ruth; Sugrue, Michele; Wingard, John R.; Alexander, Barbara D.; Follett, Sarah A.; Bowyer, Paul; Denning, David W.

    2010-01-01

    Fungal PCR-based diagnostic methods are at risk of contamination. Sample collection containers were investigated for fungal DNA contamination using real-time PCR assays. Up to 18% of blood collection tubes were contaminated with fungal DNA, probably A. fumigatus. Lower proportions of contamination in other vessels were observed.

  10. Kundt’s tube experiment using smartphones

    Science.gov (United States)

    Orsola Parolin, Sara; Pezzi, Giovanni

    2015-07-01

    This article deals with a modern version of Kundt’s tube experiment. Using economic instruments and a couple of smartphones, it is possible to ‘see’ nodes and antinodes of standing acoustic waves in a column of vibrating air and to measure the speed of sound.

  11. Holding Tubes in Place for Brazing

    Science.gov (United States)

    Ambrisco, D.; Arbino, P.

    1983-01-01

    Simple method prevents loosening due to thermal mismatch. Four segment die pushed outward against tubing wall by tapered ram. Boss on each segment of die produces dimple in wall. Ram driven by commercial pneumatic cylinder powered by air at 250 psi. Method applicable to brazing of heat exchanges, thrust chambers, and other assemblies in which thermal expansion coefficients of materials differ significantly.

  12. YouTube and Video Quizzes

    Directory of Open Access Journals (Sweden)

    Kevin YEE

    2010-04-01

    Full Text Available The Internet sensation YouTube (http://www.youtube.com has become such a force online that it was estimated in 2006 to account for a full tenth of the bandwidth by the entire Internet in the United States (WebProNews, 2007, and to use as much bandwidth in 2007 as the entire Internet had done in 2000 (Carter, 2008. Like many technological tools created with entertainment or profit in mind, YouTube can now be easily and usefully adopted by instructors for educational purposes, and indeed many professors use YouTube in their classroom teaching already (Brooks, 2000. This is especially true for passive uses of YouTube; watching videos that are already online and using them in the classroom experience to support a concept and provide another mechanism for students to connect with the topics. It is fruitful to consider Bloom's Taxonomy of Educational Objectives (Bloom & Krathwohl, 1956 when employing video or any media in the classroom to maximize the intentionality of teaching and learning. The use of video for demonstration or modeling corresponds well to Blooms levels of Knowledge, Comprehension, and Application; while case studies offer a chance to demonstrate Analysis and Synthesis, and perhaps even Evaluation, when comparing a video to information from a text book or other content.

  13. Routine jejunostomy tube feeding following esophagectomy

    NARCIS (Netherlands)

    Weijs, Teus J.|info:eu-repo/dai/nl/413993558; van Eden, Hanneke W.J.; Ruurda, Jelle P.|info:eu-repo/dai/nl/257561021; Luyer, Misha D P; Steenhagen, Elles|info:eu-repo/dai/nl/304815713; Nieuwenhuijzen, Grard A P; van Hillegersberg, Richard|info:eu-repo/dai/nl/110706242

    2017-01-01

    Background: Malnutrition is an important problem following esophagectomy. A surgically placed jejunostomy secures an enteral feeding route, facilitating discharge with home-tube feeding and long-term nutritional support. However, specific complications occur, and data are lacking that support its

  14. YouTube, dentistry, and dental education.

    Science.gov (United States)

    Knösel, Michael; Jung, Klaus; Bleckmann, Annalen

    2011-12-01

    The objective of this study was to systematically assess the informational value, intention, source, and bias of videos related to dentistry available on the video-sharing Internet platform YouTube. YouTube (www.youtube.com) was searched for videos related to dentistry, using the system-generated sorts "by relevance" and "most viewed" and two categories (All and Education). Each of the first thirty results was rated by two assessors filling out a questionnaire for each (total: 120). The data were subjected to statistical analysis using Cohen's kappa, Pearson's correlation coefficient tau, Mann-Whitney U-tests, and a nonparametric three-way ANOVA, including an analysis of the interaction between the sorting and category effect, with an α-level of 5 percent. The scan produced 279,000 results in the category All and 5,050 in the category Education. The analysis revealed a wide variety of information about dentistry available on YouTube. The purpose of these videos includes entertainment, advertising, and education. The videos classified under Education have a higher degree of usefulness and informational value for laypersons, dental students, and dental professionals than those found in a broader search category. YouTube and similar social media websites offer new educational possibilities that are currently both underdeveloped and underestimated in terms of their potential value. Dentists and dental educators should also recognize the importance of these websites in shaping public opinion about their profession.

  15. Flow induced pulsations generated in corrugated tubes

    NARCIS (Netherlands)

    Belfroid, S.P.C.; Swindell, R.; Tummers, R.

    2008-01-01

    Corrugated tubes can produce a tonal noise when used for gas transport, for instance in the case of flexible risers. The whistling sound is generated by shear layer instability due to the boundary layer separation at each corrugation. This whistling is examined by investigating the frequency,

  16. Indications and Complications of Tube Thoracostomy with ...

    African Journals Online (AJOL)

    Two perforations are created on the cap approximately 0.4 cm and 0.5 cm, respectively. Through the 0.4 cm perforation is. Indications and Complications of Tube Thoracostomy with Improvised Underwater Seal Bottles. SA Edaigbini, IZ Delia, MB Aminu, AA Orogade1, N Anumenechi, AD Ibrahim. Department of Surgery ...

  17. Tubes, Mono Jets, Squeeze Out and CME

    Energy Technology Data Exchange (ETDEWEB)

    Longacre, R. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2017-10-23

    Glasma Flux Tubes, Mono Jets with squeeze out flow around them plus the Chiral Magnetic Effect(CME) are physical phenomenon that generate two particle correlation with respect to the reaction plane in mid-central 20% to 30% Au-Au collision √sNN = 200.0 GeV measured at RHIC.

  18. Enrichment Monitor for 235U Fuel Tubes

    Energy Technology Data Exchange (ETDEWEB)

    Winn, W.G.

    2001-08-22

    This report describes the performance of this prototype y-monitor of 235 Uranium enrichment. In this proposed method y-rates associated with 235U and 232U are correlated with enrichment. Instrumentation for appraising fuel tubes with this method has been assembled and tested.

  19. Tube thoracostomy: Primary management option for empyema ...

    African Journals Online (AJOL)

    Twenty three (50%) children had history of pneumonia and treatment prior to development of empyema. Thirty five (76.08%) children ... Conclusions: Majority of children with empyema thoracis are manageable with tube thoracostomy, antibiotics, physiotherapy and other supportive treatment. Few of them who fail to above ...

  20. Cutting the L3 torque tube

    CERN Multimedia

    Laurent Guiraud

    2001-01-01

    Workers cut the torque tube, with a plasma-cutting device on the L3 experiment, which closed with the LEP accelerator in 2000. L3 was housed in a huge red solenoid, which will be taken over by the ALICE detector when the new LHC is completed.