WorldWideScience

Sample records for vibrational mode heating

  1. Vibrational modes of nanolines

    Science.gov (United States)

    Heyliger, Paul R.; Flannery, Colm M.; Johnson, Ward L.

    2008-04-01

    Brillouin-light-scattering spectra previously have been shown to provide information on acoustic modes of polymeric lines fabricated by nanoimprint lithography. Finite-element methods for modeling such modes are presented here. These methods provide a theoretical framework for determining elastic constants and dimensions of nanolines from measured spectra in the low gigahertz range. To make the calculations feasible for future incorporation in inversion algorithms, two approximations of the boundary conditions are employed in the calculations: the rigidity of the nanoline/substrate interface and sinusoidal variation of displacements along the nanoline length. The accuracy of these approximations is evaluated as a function of wavenumber and frequency. The great advantage of finite-element methods over other methods previously employed for nanolines is the ability to model any cross-sectional geometry. Dispersion curves and displacement patterns are calculated for modes of polymethyl methacrylate nanolines with cross-sectional dimensions of 65 nm × 140 nm and rectangular or semicircular tops. The vibrational displacements and dispersion curves are qualitatively similar for the two geometries and include a series of flexural, Rayleigh-like, and Sezawa-like modes. This paper is a contribution of the National Institute of Standards and Technology and is not subject to copyright in the United States.

  2. Avoid heat transfer equipment vibration

    Energy Technology Data Exchange (ETDEWEB)

    Ganapathy, V.

    1987-06-01

    Tube bundles in heat exchangers, boilers, superheaters and heaters are often subject to vibration and noise problems. Vibration can lead to tube thinning and wear, resulting in tube failures. Excessive noise can be a problem to plant operating personnel. Large gas pressure drop across the equipment is also a side effect, which results in large operating costs. With the design checks presented in this paper, one can predict during design if problems associated with noise and vibration are likely to occur in petroleum refineries.

  3. Vibration mode shape control by prestressing

    Science.gov (United States)

    Holnicki-Szulc, Jan; Haftka, Raphael T.

    1992-01-01

    A procedure is described for reducing vibration at sensitive locations on a structure, by induced distortions. The emphasis is placed on the excitation in a narrow frequency band, so that only a small number of vibration modes contribute to the intensity of the forced response. The procedure is demonstrated on an antenna truss example, showing that, with repeated frequencies, it is very easy to move nodal lines of one of the modes.

  4. Skyrmion Vibration Modes within the Rational Map Ansatz

    OpenAIRE

    Lin, W.T.; Piette, B.

    2008-01-01

    We study the vibration modes of the Skyrme model within the rational map ansatz. We show that the vibrations of the radial profiles and the rational maps are decoupled and we consider explicitly the cases B=1, B=2, and B=4. We then compare our results with the vibration modes obtained numerically by Barnes et al. and show that qualitatively the rational map reproduces the vibration modes obtained numerically but that the vibration frequencies of these modes do not match very well.

  5. Mapping vibrational surface and bulk modes in a single nanocube

    Science.gov (United States)

    Lagos, Maureen J.; Trügler, Andreas; Hohenester, Ulrich; Batson, Philip E.

    2017-03-01

    Imaging of vibrational excitations in and near nanostructures is essential for developing low-loss infrared nanophotonics, controlling heat transport in thermal nanodevices, inventing new thermoelectric materials and understanding nanoscale energy transport. Spatially resolved electron energy loss spectroscopy has previously been used to image plasmonic behaviour in nanostructures in an electron microscope, but hitherto it has not been possible to map vibrational modes directly in a single nanostructure, limiting our understanding of phonon coupling with photons and plasmons. Here we present spatial mapping of optical and acoustic, bulk and surface vibrational modes in magnesium oxide nanocubes using an atom-wide electron beam. We find that the energy and the symmetry of the surface polariton phonon modes depend on the size of the nanocubes, and that they are localized to the surfaces of the nanocube. We also observe a limiting of bulk phonon scattering in the presence of surface phonon modes. Most phonon spectroscopies are selectively sensitive to either surface or bulk excitations; therefore, by demonstrating the excitation of both bulk and surface vibrational modes using a single probe, our work represents advances in the detection and visualization of spatially confined surface and bulk phonons in nanostructures.

  6. Vibration modes and frequencies of structures

    Science.gov (United States)

    Durling, R. J.; Kvaternik, R. G.

    1980-01-01

    SUDAN, Substructuring in Direct Analysis, analyzes natural modes and frequencies of vibration of structural systems. Based on direct method of analysis that employs substructures methodology, program is used with structures that may be represented as equivalent system of beam, springs, and rigid bodies.

  7. Relating normal vibrational modes to local vibrational modes: benzene and naphthalene.

    Science.gov (United States)

    Zou, Wenli; Kalescky, Robert; Kraka, Elfi; Cremer, Dieter

    2013-07-01

    Local vibrational modes can be directly derived from normal vibrational modes using the method of Konkoli and Cremer (Int J Quant Chem 67:29, 1998). This implies the calculation of the harmonic force constant matrix F (q) (expressed in internal coordinates q) from the corresponding Cartesian force constant matrix f (x) with the help of the transformation matrix U = WB (†)(BWB (†))(-1) (B: Wilson's B-matrix). It is proven that the local vibrational modes are independent of the choice of the matrix W. However, the choice W = M (-1) (M: mass matrix) has numerical advantages with regard to the choice W = I (I: identity matrix), where the latter is frequently used in spectroscopy. The local vibrational modes can be related to the normal vibrational modes in the form of an adiabatic connection scheme (ACS) after rewriting the Wilson equation with the help of the compliance matrix. The ACSs of benzene and naphthalene based on experimental vibrational frequencies are discussed as nontrivial examples. It is demonstrated that the local-mode stretching force constants provide a quantitative measure for the C-H and C-C bond strength.

  8. Flow-induced vibration of component cooling water heat exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Yeh, Y.S.; Chen, S.S. (Taiwan Power Co., Taipei (Taiwan). Nuclear Engineering Dept.; Argonne National Lab., IL (USA))

    1990-01-01

    This paper presents an evaluation of flow-induced vibration problems of component cooling water heat exchangers in one of Taipower's nuclear power stations. Specifically, it describes flow-induced vibration phenomena, tests to identify the excitation mechanisms, measurement of response characteristics, analyses to predict tube response and wear, various design alterations, and modifications of the original design. Several unique features associated with the heat exchangers are demonstrated, including energy-trapping modes, existence of tube-support-plate (TSP)-inactive modes, and fluidelastic instability of TSP-active and -inactive modes. On the basis of this evaluation, the difficulties and future research needs for the evaluation of heat exchangers are identified. 11 refs., 19 figs., 3 tabs.

  9. Lattice vibrational modes and their frequency shifts in semiconductor nanowires.

    Science.gov (United States)

    Yang, Li; Chou, M Y

    2011-07-13

    We have performed first-principles calculations to study the lattice vibrational modes and their Raman activities in silicon nanowires (SiNWs). Two types of characteristic vibrational modes are examined: high-frequency optical modes and low-frequency confined modes. Their frequencies have opposite size dependence with a red shift for the optical modes and a blue shift for the confined modes as the diameter of SiNWs decreases. In addition, our calculations show that these vibrational modes can be detected by Raman scattering measurements, providing an efficient way to estimate the size of SiNWs.

  10. Function generator for synthesizing complex vibration mode patterns

    Science.gov (United States)

    Naumann, E. C.; Hagood, G. J., Jr. (Inventor)

    1973-01-01

    A simple highly flexible device for synthesizing complex vibration mode patterns is described. These mode patterns can be used to identify vibration mode data. This device sums selected sine and cosine functions and then plots the sum against a linear function.

  11. Single-molecule electronics: Cooling individual vibrational modes by the tunneling current.

    Science.gov (United States)

    Lykkebo, Jacob; Romano, Giuseppe; Gagliardi, Alessio; Pecchia, Alessandro; Solomon, Gemma C

    2016-03-21

    Electronic devices composed of single molecules constitute the ultimate limit in the continued downscaling of electronic components. A key challenge for single-molecule electronics is to control the temperature of these junctions. Controlling heating and cooling effects in individual vibrational modes can, in principle, be utilized to increase stability of single-molecule junctions under bias, to pump energy into particular vibrational modes to perform current-induced reactions, or to increase the resolution in inelastic electron tunneling spectroscopy by controlling the life-times of phonons in a molecule by suppressing absorption and external dissipation processes. Under bias the current and the molecule exchange energy, which typically results in heating of the molecule. However, the opposite process is also possible, where energy is extracted from the molecule by the tunneling current. Designing a molecular "heat sink" where a particular vibrational mode funnels heat out of the molecule and into the leads would be very desirable. It is even possible to imagine how the vibrational energy of the other vibrational modes could be funneled into the "cooling mode," given the right molecular design. Previous efforts to understand heating and cooling mechanisms in single molecule junctions have primarily been concerned with small models, where it is unclear which molecular systems they correspond to. In this paper, our focus is on suppressing heating and obtaining current-induced cooling in certain vibrational modes. Strategies for cooling vibrational modes in single-molecule junctions are presented, together with atomistic calculations based on those strategies. Cooling and reduced heating are observed for two different cooling schemes in calculations of atomistic single-molecule junctions.

  12. Hydrogen local vibrational modes in semiconductors

    Energy Technology Data Exchange (ETDEWEB)

    McCluskey, Matthew D. [Univ. of California, Berkeley, CA (United States). Dept. of Physics

    1997-06-01

    Following, a review of experimental techniques, theory, and previous work, the results of local vibrational mode (LVM) spectroscopy on hydrogen-related complexes in several different semiconductors are discussed. Hydrogen is introduced either by annealing in a hydrogen ambient. exposure to a hydrogen plasma, or during growth. The hydrogen passivates donors and acceptors in semiconductors, forming neutral complexes. When deuterium is substituted for hydrogen. the frequency of the LVM decreases by approximately the square root of two. By varying the temperature and pressure of the samples, the microscopic structures of hydrogen-related complexes are determined. For group II acceptor-hydrogen complexes in GaAs, InP, and GaP, hydrogen binds to the host anion in a bond-centered orientation, along the [111] direction, adjacent to the acceptor. The temperature dependent shift of the LVMs are proportional to the lattice thermal energy U(T), a consequence of anharmonic coupling between the LVM and acoustical phonons. In the wide band gap semiconductor ZnSe, epilayers grown by metalorganic chemical vapor phase epitaxy (MOCVD) and doped with As form As-H complexes. The hydrogen assumes a bond-centered orientation, adjacent to a host Zn. In AlSb, the DX centers Se and Te are passivated by hydrogen. The second, third, and fourth harmonics of the wag modes are observed. Although the Se-D complex has only one stretch mode, the Se-H stretch mode splits into three peaks. The anomalous splitting is explained by a new interaction between the stretch LVM and multi-phonon modes of the lattice. As the temperature or pressure is varied, and anti-crossing is observed between LVM and phonon modes.

  13. Inhibiting multiple mode vibration in controlled flexible systems

    Science.gov (United States)

    Hyde, James M.; Chang, Kenneth W.; Seering, Warren P.

    1991-01-01

    Viewgraphs on inhibiting multiple mode vibration in controlled flexible systems are presented. Topics covered include: input pre-shaping background; developing multiple-mode shapers; Middeck Active Control Experiment (MACE) test article; and tests and results.

  14. Chaotic vibrations of heated plates

    Science.gov (United States)

    Fermen-Coker, Muge

    1998-12-01

    In recent years, the investigation of dynamical behavior of plates under thermal loads has become important due to the high temperatures reached on external skin panels of hypersonic vehicles. It has been shown by other researchers that the skin panels may encounter chaotic vibrations about their thermally buckled positions. In this research, the chaotic vibrations of simply supported plates under thermal and sinusoidal excitation is studied in order to predict the vibratory behavior of a representative class of such skin panels. A method for the development of equations of motion, that forms a foundation for further investigation of the response of elastic panels under general thermal, mechanical and aerodynamic loading and various boundary conditions, is presented and discussed. The boundaries of regular and chaotic regions of motion are defined and the sensitivity of these boundaries to changes in design parameters is explored for the purpose of developing useful design criteria. The onset of chaos is predicted through the computation of Lyapunov exponents. The sensitivity of Lyapunov exponent calculations to the choice of numerical method of integration, numerical precision and the magnitude of coefficients as functions of design variables, is discussed. The effects of thermal moment, thermal buckling, amplitude and frequency of excitation, damping, thickness and length to width ratio of panels on the onset of chaos is studied. The results of the research are presented as a contribution to the panel design of hypersonic vehicles.

  15. Vibration Method for Tracking the Resonant Mode and Impedance of a Microwave Cavity

    Science.gov (United States)

    Barmatz, M.; Iny, O.; Yiin, T.; Khan, I.

    1995-01-01

    A vibration technique his been developed to continuously maintain mode resonance and impedance much between a constant frequency magnetron source and resonant cavity. This method uses a vibrating metal rod to modulate the volume of the cavity in a manner equivalent to modulating an adjustable plunger. A similar vibrating metal rod attached to a stub tuner modulates the waveguide volume between the source and cavity. A phase sensitive detection scheme determines the optimum position of the adjustable plunger and stub turner during processing. The improved power transfer during the heating of a 99.8% pure alumina rod was demonstrated using this new technique. Temperature-time and reflected power-time heating curves are presented for the cases of no tracking, impedance tracker only, mode tracker only and simultaneous impedance and mode tracking. Controlled internal melting of an alumina rod near 2000 C using both tracking units was also demonstrated.

  16. Ultrafast Dynamics of Vibration-Cavity Polariton Modes

    Science.gov (United States)

    Owrutsky, Jeff; Dunkelberger, Adam; Fears, Kenan; Simpkins, Blake; Spann, Bryan

    Vibrational modes of polymers, liquids, and solvated compounds can couple to Fabry-Perot optical cavity modes, creating vibration-cavity polariton modes whose energy tunes with the cavity length and incidence angle. Here we report the pump-probe infrared spectroscopy of vibration-cavity polaritons in cavity-coupled W(CO)6. At very early times, we observe quantum beating between the two polariton states find an anomalously low degree of excitation. After the quantum beating, we directly observe spectroscopic signatures of excited-state absorption from both polariton modes and uncoupled reservoir modes. An analytical expression for cavity transmission reproduces these signatures. The upper polariton mode relaxes ten times more quickly than the uncoupled vibrational mode and the polariton lifetime depends on the angle of incidence of the infrared pulses. Coupling to an optical cavity gives a means of control of the lifetime of vibration-cavity polaritons and could have important implications for chemical reactivity in vibrationally excited molecules.

  17. Computing Vibration-Mode Matrices From Finite-Element Output

    Science.gov (United States)

    Levy, Roy

    1993-01-01

    Postprocessing algorithms devised to facilitate vibrational-mode analyses of dynamics of complicated structures. Yields inertia matrices and elastic/rigid-coupling matrices. Such analyses important in simulation and control in active suppression of vibrations in large building or in precise aiming of large antenna.

  18. selective excitation of vibrational modes of polyatomic molecule

    Indian Academy of Sciences (India)

    Abstract. Mode-selective dynamics of triatomic molecule in the electronic ground state under continuous wave laser pulse is investigated for the discrete vibrational bound states. A non-perturbative approach has been used to analyse the vibrational couplings and dynamics of the molecule. Keywords. Polyatomic molecule ...

  19. Vibration-induced coherence enhancement of the performance of a biological quantum heat engine.

    Science.gov (United States)

    Chen, Hong-Bin; Chiu, Pin-Yi; Chen, Yueh-Nan

    2016-11-01

    Photosynthesis has been a long-standing research interest due to its fundamental importance. Recently, studies on photosynthesis processes also have inspired attention from a thermodynamical aspect when considering photosynthetic apparatuses as biological quantum heat engines. Quantum coherence is shown to play a crucial role in enhancing the performance of these quantum heat engines. Based on the experimentally reported structure, we propose a quantum heat engine model with a non-Markovian vibrational mode. We show that one can obtain a performance enhancement easily for a wide range of parameters in the presence of the vibrational mode. Our results provide insights into the photosynthetic processes and a design principle mimicking natural organisms.

  20. Vibration-induced coherence enhances the performance of a biological quantum heat engine

    CERN Document Server

    Chen, Hong-Bin; Chen, Yueh-Nan

    2016-01-01

    Photosynthesis has been the long-standing research interest due to its fundamental importance. Recently, studies on photosynthesis processes also inspire attention from thermodynamical aspect when considering photosynthetic apparatuses as biological quantum heat engines. Quantum coherence is shown to play a crucial role in enhancing the performance of these quantum heat engines. Based on the experimentally reported structure, we propose a quantum heat engine model with a non-Markovian vibrational mode. We show that one can obtain a performance enhancement easily for a wide range of parameters in the presence of the vibrational mode. Our results suggest new insights into the photosynthetic processes and a design principle mimicking natural organisms.

  1. Automobile Road Vibration Reproduction using Sliding Modes

    NARCIS (Netherlands)

    Monsees, G.; Scherpen, J.M.A.

    2001-01-01

    Sliding mode controllers have a reputation for their robustness against parameter variations, modeling errors and disturbances. They have been successfully applied in several practical situations which demonstrated the potential of sliding mode control for other control problems. However research

  2. Pulsed differential holographic measurements of vibration modes of high temperature panels

    Science.gov (United States)

    Evensen, D. A.; Aprahamian, R.; Overoye, K. R.

    1972-01-01

    Holography is a lensless imaging technique which can be applied to measure static or dynamic displacements of structures. Conventional holography cannot be readily applied to measure vibration modes of high-temperature structures, due to difficulties caused by thermal convection currents. The present report discusses the use of pulsed differential holography, which is a technique for recording structural motions in the presence of random fluctuations such as turbulence. An analysis of the differential method is presented, and demonstration experiments were conducted using heated stainless steel plates. Vibration modes were successfully recorded for the heated plates at temperatures of 1000, 1600, and 2000 F. The technique appears promising for such future measurments as vibrations of the space shuttle TPS panels or recording flutter of aeroelastic models in a wind-tunnel.

  3. Evaluation of Bus Vibration Comfort Based on Passenger Crowdsourcing Mode

    Directory of Open Access Journals (Sweden)

    Hong Zhao

    2016-01-01

    Full Text Available Vibration comfort is an important factor affecting the quality of service (QoS of bus. In order to make people involved in supervising bus’s vibration comfort and improve passengers’ riding experience, a novel mode of passenger crowdsourcing is introduced. In this paper, comfort degree of bus vibration is calculated from bus’s vibration signals collected by passengers’ smartphones and sent through WiFi to the Boa web server which shows the vibration comfort on the LCD deployed in bus and maybe trigger alarm lamp when the vibration is beyond the threshold. Three challenges here have been overcome: firstly, space coordinate transformation algorithm is used to solve the constant drift of signals collected; secondly, a low-pass filter is designed to isolate gravity from signals real-timely via limited computing resources; thirdly, an embedded evaluation system is developed according to the calculation procedure specified by criterion ISO 2631-1997. Meanwhile, the model proposed is tested in a practical running environment, the vibration data in whole travel are recorded and analyzed offline. The results show that comfort degree of vibration obtained from the experimental system is identical with the truth, and this mode is proved to be effective.

  4. Signature of nonadiabatic coupling in excited-state vibrational modes.

    Science.gov (United States)

    Soler, Miguel A; Nelson, Tammie; Roitberg, Adrian E; Tretiak, Sergei; Fernandez-Alberti, Sebastian

    2014-11-13

    Using analytical excited-state gradients, vibrational normal modes have been calculated at the minimum of the electronic excited-state potential energy surfaces for a set of extended conjugated molecules with different coupling between them. Molecular model systems composed of units of polyphenylene ethynylene (PPE), polyphenylenevinylene (PPV), and naphthacene/pentacene (NP) have been considered. In all cases except the NP model, the influence of the nonadiabatic coupling on the excited-state equilibrium normal modes is revealed as a unique highest frequency adiabatic vibrational mode that overlaps with the coupling vector. This feature is removed by using a locally diabatic representation in which the effect of NA interaction is removed. Comparison of the original adiabatic modes with a set of vibrational modes computed in the locally diabatic representation demonstrates that the effect of nonadiabaticity is confined to only a few modes. This suggests that the nonadiabatic character of a molecular system may be detected spectroscopically by identifying these unique state-specific high frequency vibrational modes.

  5. Beyond local group modes in vibrational sum frequency generation.

    Science.gov (United States)

    Chase, Hilary M; Psciuk, Brian T; Strick, Benjamin L; Thomson, Regan J; Batista, Victor S; Geiger, Franz M

    2015-04-09

    We combine deuterium labeling, density functional theory calculations, and experimental vibrational sum frequency generation spectroscopy into a form of "counterfactual-enabled molecular spectroscopy" for producing reliable vibrational mode assignments in situations where local group mode approximations are insufficient for spectral interpretation and vibrational mode assignments. We demonstrate the method using trans-β-isoprene epoxydiol (trans-β-IEPOX), a first-generation product of isoprene relevant to atmospheric aerosol formation, and one of its deuterium-labeled isotopologues at the vapor/silica interface. We use our method to determine that the SFG responses that we obtain from trans-β-IEPOX are almost exclusively due to nonlocal modes involving multiple C-H groups oscillating at the same frequency as one vibrational mode. We verify our assignments using deuterium labeling and use DFT calculations to predict SFG spectra of additional isotopologues that have not yet been synthesized. Finally, we use our new insight to provide a viable alternative to molecular orientation analysis methods that rely on local mode approximations in cases where the local mode approximation is not applicable.

  6. Broadband vibration energy harvester utilizing three out-of-plane modes of one vibrating body

    Science.gov (United States)

    Park, Shi-Baek; Jang, Seon-Jun; Kim, In-Ho; Choi, Yong Je

    2017-10-01

    In this paper, we introduce the concept, design equation, and realization of a broadband electromagnetic vibrational energy harvester. The spatial vibrating system in the proposed harvester is arranged to have three out-of-plane vibration modes. We devise the design method for its three natural frequencies and accompanying modes and apply it to the broadband energy harvesting by locating three frequencies close to each other. The numerical simulation and the experimental results show that it satisfies the designated frequencies as well as the enhanced bandwidth for power generation.

  7. Fundamental vibrational mode in a highly inhomogeneous star

    OpenAIRE

    Bastrukov, S. I.; Chang, H. -K.; Wu, E. -H.; Molodtsova, I. V.

    2008-01-01

    The eigenfrequency problem of fundamental vibrational mode in a highly inhomogeneous star, modeled by self-gravitating mass of viscous liquid with singular density at the center, is considered in juxtaposition with that for Kelvin fundamental mode in the liquid star model with uniform density. Particular attention is given to the difference between spectral equations for the frequency and lifetime of f-mode in the singular and homogeneous star models. The newly obtained results are discussed ...

  8. Linking crystal structure with temperature-sensitive vibrational modes in calcium carbonate minerals.

    Science.gov (United States)

    Xu, Ben; Poduska, Kristin M

    2014-09-07

    We demonstrate a correlation between how an IR-active vibrational mode responds to temperature changes and how it responds to crystallinity differences. Infrared (IR) spectroscopy was used to track changes in carbonate-related vibrational modes in three different CaCO3 polymorphs (calcite, aragonite, and vaterite) and CaMg(CO3)2 (dolomite) during heating. Of the three characteristic IR-active carbonate modes, the in-plane bending mode (ν4) shows the most pronounced changes with heating in polymorphs that have planar carbonate arrangements (calcite, aragonite, and dolomite). In contrast, this mode is virtually unchanged in vaterite, which has a canted arrangement of carbonate units. We correlate these trends with recent studies that identified the ν4 mode as most susceptible to changes related to crystallinity differences in calcite and amorphous calcium carbonate. Thus, our results suggest that studies of packing arrangements could provide a generalizable approach to identify the most diagnostic vibrational modes for tracking either temperature-dependent or crystallinity-related effects in IR-active solids.

  9. DOE/ANL/HTRI heat exchanger tube vibration data bank

    Energy Technology Data Exchange (ETDEWEB)

    Halle, H.; Chenoweth, J.M.; Wambsganss, M.W.

    1981-01-01

    This addendum to the DOE/ANL/HTRI Heat Exchanger Tube Vibration Data Bank includes 16 new case histories of field experiences. The cases include several exchangers that did not experience vibration problems and several for which acoustic vibration was reported.

  10. The normal modes of lattice vibrations of ice XI

    Science.gov (United States)

    Zhang, Peng; Wang, Zhe; Lu, Ying-Bo; Ding, Zheng-Wen

    2016-01-01

    The vibrational spectrum of ice XI at thermal wavelengths using the CASTEP code, a first-principles simulation method, is investigated. A dual-track approach is constructed to verify the validity for the computational phonon spectrum: collate the simulated spectrum with inelastic neutron scattering experiments and assign the photon scattering peaks according to the calculated normal vibration frequencies. The 33 optical normal vibrations at the Brillouin center are illustrated definitely from the ab initio outcomes. The depolarizing field effect of the hydrogen bond vibrations at frequencies of 229 cm−1 and 310 cm−1 is found to agree well with the LST relationship. It is a convincing evidence to manifest the LO-TO splitting of hydrogen bonds in ice crystal. We attribute the two hydrogen bond peaks to the depolarization effect and apply this viewpoint to ordinary ice phase, ice Ih, which is difficult to analyse their vibration modes due to proton disorder. PMID:27375199

  11. Surface vibrational modes in disk-shaped resonators.

    Science.gov (United States)

    Dmitriev, A V; Gritsenko, D S; Mitrofanov, V P

    2014-03-01

    The natural frequencies and distributions of displacement components for the surface vibrational modes in thin isotropic elastic disks are calculated. In particular, the research is focused on even solutions for low-lying resonant vibrations with large angular wave numbers. Several families of modes are found which are interpreted as modified surface modes of an infinitely long cylinder and Lamb modes of a plate. The results of calculation are compared with the results of the experimental measurements of vibrational modes generated by means of resonant excitation in duraluminum disk with radius of ≈90 mm and thickness of 16 mm in the frequency range of 130-200 kHz. An excellent agreement between the calculated and measured frequencies is found. Measurements of the structure of the resonant peaks show splitting of some modes. About a half of the measured modes has splitting Δfsplit/fmode at the level of the order of 10(-5). The Q-factors of all modes measured in vacuum lie in the interval (2…3)×10(5). This value is typical for duraluminum mechanical resonators in the ultrasonic frequency range. Copyright © 2013 Elsevier B.V. All rights reserved.

  12. Orifice Blocks Heat Pipe in Reverse Mode

    Science.gov (United States)

    Alario, J. P.

    1982-01-01

    High forward-mode conductance is combined with rapid reverse-mode shutoff in a heat pipe originally developed to cool spacecraft payloads. A narrow orifice within the pipe "chokes off" the evaporator if heat sink becomes warmer than source. During normal operation, with source warmer than sink, orifice has little effect. Design is simpler and more compact than other thermal-diode heat pipes and requires no special materials, forgings, or unusual construction techniques.

  13. Characterizing the free and surface-coupled vibrations of heated-tip atomic force microscope cantilevers.

    Science.gov (United States)

    Killgore, Jason P; Tung, Ryan C; Hurley, Donna C

    2014-08-29

    Combining heated-tip atomic force microscopy (HT-AFM) with quantitative methods for determining surface mechanical properties, such as contact resonance force microscopy, creates an avenue for nanoscale thermomechanical property characterization. For nanomechanical methods that employ an atomic force microscope cantilever's vibrational modes, it is essential to understand how the vibrations of the U-shaped HT-AFM cantilever differ from those of a more traditional rectangular lever, for which analytical techniques are better developed. Here we show, with a combination of finite element analysis (FEA) and experiments, that the HT-AFM cantilever exhibits many more readily-excited vibrational modes over typical AFM frequencies compared to a rectangular cantilever. The arms of U-shaped HT-AFM cantilevers exhibit two distinct forms of flexural vibrations that differ depending on whether the two arms are vibrating in-phase or out-of-phase with one another. The in-phase vibrations are qualitatively similar to flexural vibrations in rectangular cantilevers and generally show larger sensitivity to surface stiffness changes than the out-of-phase vibrations. Vibration types can be identified from their frequency and by considering vibration amplitudes in the horizontal and vertical channels of the AFM at different laser spot positions on the cantilever. For identifying contact resonance vibrational modes, we also consider the sensitivity of the resonant frequencies to a change in applied force and hence to tip-sample contact stiffness. Finally, we assess how existing analytical models can be used to accurately predict contact stiffness from contact-resonance HT-AFM results. A simple two-parameter Euler-Bernoulli beam model provided good agreement with FEA for in-phase modes up to a contact stiffness 500 times the cantilever spring constant. By providing insight into cantilever vibrations and exploring the potential of current analysis techniques, our results lay the groundwork

  14. Phonon Transport at Crystalline Si/Ge Interfaces: The Role of Interfacial Modes of Vibration.

    Science.gov (United States)

    Gordiz, Kiarash; Henry, Asegun

    2016-03-16

    We studied the modal contributions to heat conduction at crystalline Si and crystalline Ge interfaces and found that more than 15% of the interface conductance arises from less than 0.1% of the modes in the structure. Using the recently developed interface conductance modal analysis (ICMA) method along with a new complimentary methodology, we mapped the correlations between modes, which revealed that a small group of interfacial modes, which exist between 12-13 THz, exhibit extremely strong correlation with other modes in the system. It is found that these interfacial modes (e.g., modes with large eigen vectors for interfacial atoms) are enabled by the degree of anharmonicity near the interface, which is higher than in the bulk, and therefore allows this small group of modes to couple to all others. The analysis sheds light on the nature of localized vibrations at interfaces and can be enlightening for other investigations of localization.

  15. Electric field generated by axial longitudinal vibration modes of microtubule.

    Science.gov (United States)

    Cifra, M; Pokorný, J; Havelka, D; Kucera, O

    2010-05-01

    Microtubules are electrically polar structures fulfilling prerequisites for generation of oscillatory electric field in the kHz to GHz region. Energy supply for excitation of elasto-electrical vibrations in microtubules may be provided from GTP-hydrolysis; motor protein-microtubule interactions; and energy efflux from mitochondria. We calculated electric field generated by axial longitudinal vibration modes of microtubules for random, and coherent excitation. In case of coherent excitation of vibrations, the electric field intensity is highest at the end of microtubule. The dielectrophoretic force exerted by electric field on the surrounding molecules will influence the kinetics of microtubule polymerization via change in the probability of the transport of charge and mass particles. The electric field generated by vibrations of electrically polar cellular structures is expected to play an important role in biological self-organization. 2010 Elsevier Ireland Ltd. All rights reserved.

  16. CO laser photoacoustic spectra and vibrational modes of heroin ...

    Indian Academy of Sciences (India)

    Abstract. Heroin, morphine and narcotine are very large molecules having 50, 40 and 53 atoms respectively. Moderately high resolution photoacoustic (PA) spectra have been recorded in 9.6 µm and 10.6 µm regions of CO2 laser. It is very difficult to assign the modes of vibrations for PA bands by comparison with ...

  17. laser photoacoustic spectra and vibrational modes of heroin ...

    Indian Academy of Sciences (India)

    Heroin, morphine and narcotine are very large molecules having 50, 40 and 53 atoms respectively. Moderately high resolution photoacoustic (PA) spectra have been recorded in 9.6 m and 10.6 m regions of CO2 laser. It is very difficult to assign the modes of vibrations for PA bands by comparison with conventional low ...

  18. Two-mode elliptical-core weighted fiber sensors for vibration analysis

    Science.gov (United States)

    Vengsarkar, Ashish M.; Murphy, Kent A.; Fogg, Brian R.; Miller, William V.; Greene, Jonathan A.; Claus, Richard O.

    1992-01-01

    Two-mode, elliptical-core optical fibers are demonstrated in weighted, distributed and selective vibration-mode-filtering applications. We show how appropriate placement of optical fibers on a vibrating structure can lead to vibration mode filtering. Selective vibration-mode suppression on the order of 10 dB has been obtained using tapered two-mode, circular-core fibers with tapering functions that match the second derivatives of the modes of vibration to be enhanced. We also demonstrate the use of chirped, two-mode gratings in fibers as spatial modal sensors that are equivalents of shaped piezoelectric sensors.

  19. The influence of longitudinal vibrations on the heat transfer performance of inclined heat pipes

    National Research Council Canada - National Science Library

    Chen, Rong-Horng; Kuo, LW; Lai, Chi-Ming

    2015-01-01

    This study focused on investigating the influence of longitudinal vibrations, the condensation section temperature, and the inclination angles on the heat transfer performance of grooved cylindrical...

  20. Optically active vibrational modes of PPV derivatives on textile substrate

    Energy Technology Data Exchange (ETDEWEB)

    Silva, M.A.T. da, E-mail: seaquinhos@uel.br [Departamento de Fisica, Universidade Estadual de Londrina-UEL, PR 445 Km 380, CP6001, CEP 86051-970 Londrina, Parana (Brazil); Dias, I.F.L. [Departamento de Fisica, Universidade Estadual de Londrina-UEL, PR 445 Km 380, CP6001, CEP 86051-970 Londrina, Parana (Brazil); Santos, E.P. dos; Martins, A.A. [Departamento de Fisica, Universidade Vale do Paraiba-UNIVAP, Avenida Shishima Hifumi, 2911, CEP 12244-000 Sao Jose dos Campos, Sao Paulo (Brazil); Duarte, J.L.; Laureto, E.; Reis, G.A. dos [Departamento de Fisica, Universidade Estadual de Londrina-UEL, PR 445 Km 380, CP6001, CEP 86051-970 Londrina, Parana (Brazil); Guimaraes, P.S.S.; Cury, L.A. [Departamento de Fisica, Instituto de Ciencias Exatas, Universidade Federal de Minas Gerais, C.P. 702, Belo Horizonte, CEP 30123-970 Minas Gerais (Brazil)

    2013-02-15

    In this work, MEH-PPV and BDMO-PPV films were deposited by spin-coating on 'dirty' textile substrates of canvas, nylon, canvas with resin, jeans and on glass and the temperature dependence of the optical properties of them was studied by photoluminescence and Raman (300 K) techniques. The temperature dependence of the energy, of the half line width at half height of the purely electronic peak, of the integrated PL intensity and of the Huang-Rhys factor, S=I{sub (01)}/I{sub (00)}, were obtained directly from the PL spectrum. For an analysis of the vibrational modes involved, Raman measurements were performed on substrates with and without polymers deposited and the results compared with those found in the literature. The films of MEH-PPV and BDMO-PPV showed optical properties similar to those films deposited on other substrates such as glass, metals, etc. It was observed an inversion of the first vibrational band in relation to the purely electronic peak with increasing temperature in the films deposited on nylon and canvas. The vibrational modes obtained by Raman were used to compose the simulation of the PL line shape of BDMO-PPV films on canvas and nylon, using a model proposed by Lin [29]. - Highlights: Black-Right-Pointing-Pointer MEH-PPV and BDMO-PPV films were deposited by spin-coating on dirty textile. Black-Right-Pointing-Pointer Their properties were studied by photoluminescence and Raman techniques. Black-Right-Pointing-Pointer We observed inversion of first vibrational band in relation to purely electronic peak. Black-Right-Pointing-Pointer Optically active vibrational modes of PPV derivatives were studied.

  1. Flow distribution and tube vibration in heat exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, H.L.

    1985-07-01

    A project was initiated to study flow distribution and tube vibration in heat exchangers. An experimental program was carried out on a full-size heat exchanger in four test phases of parametric study. The flow induced vibration data were used to quantify and develop non-intrusive vibration monitoring techniques for online problem evaluation and to study the influence of design features and conditions on the vibration. The in-tube vibration data obtained have shown that the vibroacoustic and microphone monitoring techniques to be reliable and accurate methods for the detection of tube impacting in an operating heat exchanger. Development of work on the use of a two-accelerator vibroacoustic technique for the location of impacting zones in a bundle showed promise and is currently being employed in the field. The in-tube vibration data have demonstrated the effects that changes in the design of a bundle can have on tube vibration in that bundle. These results indicate that an important factor in bundle design is the local flow distribution in areas of high vibration susceptibility. The in-tube data have demonstrated that tubes in zones other than the inlet region can be susceptible to a form of periodic resonant excitation. This observation has implications for cases where flow reduction is implemented to avoid an instability problem. Such a reduction could bring the tube bundle into a flow regime where it is susceptible to the resonant excitation. 10 refs., 55 figs., 4 tabs.

  2. Displacement of polarons by vibrational modes in doped conjugated polymers

    Science.gov (United States)

    Anderson, M.; Ramanan, C.; Fontanesi, C.; Frick, A.; Surana, S.; Cheyns, D.; Furno, M.; Keller, T.; Allard, S.; Scherf, U.; Beljonne, D.; D'Avino, G.; von Hauff, E.; Da Como, E.

    2017-10-01

    Organic pi-conjugated polymers are deemed to be soft materials with strong electron-phonon coupling, which results in the formation of polarons, i.e., charge carriers dressed by self-localized distortion of the nuclei. Universal signatures for polarons are optical resonances below the band gap and intense vibrational modes (IVMs), both found in the infrared (IR) spectral region. Here, we study p -doped conjugated homo- and copolymers by combining first-principles modelling and optical spectroscopy from the far-IR to the visible. Polaronic IVMs are found to feature absorption intensities comparable to purely electronic transitions and, most remarkably, show only loose resemblance to the Raman or IR-active modes of the neutral polymer. The IVM frequency is dramatically scaled down (up to 50%) compared to the backbone carbon-stretching modes in the pristine polymers. The very large intensity of IVMs is associated with displacement of the excess positive charge along the backbone driven by specific vibrational modes. We propose a quantitative picture for the identification of these polaron shifting modes that solely based on structural information, directly correlates with their IR intensity. This finding finally discloses the elusive microscopic mechanism behind the huge IR intensity of IVMs in doped polymeric semiconductors.

  3. Piezoelectric nonlinear vibration focusing on the second-harmonic vibration mode.

    Science.gov (United States)

    Ozaki, Ryohei; Liu, Yaoyang; Hosaka, Hiroshi; Morita, Takeshi

    2018-01-01

    Resonant piezoelectric devices are driven under high power condition. In such condition, a nonlinear piezoelectric vibration becomes apparent and this nonlinearity should be taken into account in the design procedure using the finite elemental method (FEM). The purpose of this study is to introduce the nonlinear parameter to the FEM and to establish the method for measuring the nonlinear parameter through evaluating a nonlinear model for a piezoelectric vibration. In a previous study about the nonlinear piezoelectric vibration, the third term was mainly focused on because the third mode vibration affects the fundamental vibration in the case of a simple bar-type transducer. On the other hand, we considered the second nonlinear parameter of the compliance to the piezoelectric constitutive equation. We observed that this parameter affects the vibration amplitude with each position and the velocity at the tip of the transducer with a double frequency at resonant. It was confirmed that two measured nonlinear parameters based on these two relationships were almost same. From these values, we concluded that the proposed model is reasonable. Copyright © 2017. Published by Elsevier B.V.

  4. Heavy atom vibrational modes and low-energy vibrational autodetachment in nitromethane anions

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, Michael C.; Weber, J. Mathias, E-mail: weberjm@jila.colorado.edu [JILA, University of Colorado at Boulder, 440 UCB, Boulder, Colorado 80309-0440 (United States); Department of Chemistry and Biochemistry, University of Colorado at Boulder, 215UCB, Boulder, Colorado 80309-0215 (United States); Baraban, Joshua H. [Department of Chemistry and Biochemistry, University of Colorado at Boulder, 215UCB, Boulder, Colorado 80309-0215 (United States); Matthews, Devin A. [Institute for Computational Engineering and Science, University of Texas at Austin, 201 E. 24th St., Austin, Texas 78712 (United States); Stanton, John F. [Department of Chemistry and Biochemistry, University of Texas at Austin, 1 University Station A5300, Austin, Texas 78712-0165 (United States)

    2015-06-21

    We report infrared spectra of nitromethane anion, CH{sub 3}NO{sub 2}{sup −}, in the region 700–2150 cm{sup −1}, obtained by Ar predissociation spectroscopy and electron detachment spectroscopy. The data are interpreted in the framework of second-order vibrational perturbation theory based on coupled-cluster electronic structure calculations. The modes in the spectroscopic region studied here are mainly based on vibrations involving the heavier atoms; this work complements earlier studies on nitromethane anion that focused on the CH stretching region of the spectrum. Electron detachment begins at photon energies far below the adiabatic electron affinity due to thermal population of excited vibrational states.

  5. Comparison of different ultrasonic vibration modes for post removal.

    Science.gov (United States)

    Braga, Neilor Mateus Antunes; Silva, Juliana Monteiro da; Carvalho-Júnior, Jacy Ribeiro de; Ferreira, Raquel Conceição; Saquy, Paulo César; Brito-Júnior, Manoel

    2012-01-01

    This in vitro study compared different ultrasonic vibration modes for intraradicular cast post removal. The crowns of 24 maxillary canines were removed, the roots were embedded in acrylic resin blocks, and the canals were treated endodontically. The post holes were prepared and root canal impressions were taken with self-cured resin acrylic. After casting, the posts were cemented with zinc phosphate cement. The samples were randomly distributed into 3 groups (n=8): G1: no ultrasonic vibration (control); G2: tip of the ultrasonic device positioned perpendicularly to core surface and close to the incisal edge; and G3: tip of the ultrasonic device positioned perpendicularly to core surface at cervical region, close to the line of cementation. An Enac OE-5 ultrasound unit with an ST-09 tip was used. All samples were submitted to the tensile test using an universal testing machine at a crosshead speed of 1 mm/min. Data were subjected to one-way ANOVA and Tukey's post-hoc tests (α=0.05). Mean values of the load to dislodge the posts (MPa) were: G1 = 4.6 (± 1.4) A; G2 = 2.8 (± 0.9) B, and G3= 0.9 (± 0.3) C. Therefore, the ultrasonic vibration applied with the tip of device close to the core's cervical area showed higher ability to reduce the retention of cast post to root canal.

  6. Vibration modes of injured spine at resonant frequencies under vertical vibration.

    Science.gov (United States)

    Guo, Li-Xin; Zhang, Ming; Zhang, Yi-Min; Teo, Ee-Chon

    2009-09-01

    A detailed three-dimensional finite element model of the spine segment T12-Pelvis was developed to investigate dynamic characteristics of whole lumbar spine with injured cases. This study investigates the motion mechanism of the human lumbar spine and the effect of component injuries on adjacent spinal components under whole body vibration. Several investigations have analyzed the influence of injured spines on adjacent spinal components under static loadings. However, it is not clear how the spine injury affects dynamic characteristics of whole lumbar spine and adjacent components of the injured segment under vibration. The T12-Pelvis model was used to obtain the modal vibration modes of the spine at resonant frequencies. Injury conditions of the spine were simulated and tested, including denucleation and/or facetectomy with removal of capsular ligaments. The results indicate the first-order vertical resonant frequency of the intact model is 7.21 Hz. After the denucleation at L4-L5, it decreases by more than 4% compared with the intact condition. All the injured conditions including disc injury and ligament injury decrease the resonant frequency of the spine. Due to the denucleation at L4-L5 the anteroposterior displacements of the vertebrae from L2 to L5 decrease and the vertical displacements of the vertebrae from L1 to L4 increase under vibration. The denucleation also decreases the rotational deformations of the vertebrae from L1 to L5. The material property sensitivity analysis shows intervertebral discs have a dominating effect on variation of vertical resonant frequency of the spine. The denucleation may decrease cushioning effects of adjacent motion segments at the injured level under vibration. The injured condition may increase the vertical displacement amplitudes of the spine above the injured level. All the injured conditions may decrease the resonant frequency of the spine system.

  7. A Novel Vibration Mode Testing Method for Cylindrical Resonators Based on Microphones

    Directory of Open Access Journals (Sweden)

    Yongmeng Zhang

    2015-01-01

    Full Text Available Non-contact testing is an important method for the study of the vibrating characteristic of cylindrical resonators. For the vibratory cylinder gyroscope excited by piezo-electric electrodes, mode testing of the cylindrical resonator is difficult. In this paper, a novel vibration testing method for cylindrical resonators is proposed. This method uses a MEMS microphone, which has the characteristics of small size and accurate directivity, to measure the vibration of the cylindrical resonator. A testing system was established, then the system was used to measure the vibration mode of the resonator. The experimental results show that the orientation resolution of the node of the vibration mode is better than 0.1°. This method also has the advantages of low cost and easy operation. It can be used in vibration testing and provide accurate results, which is important for the study of the vibration mode and thermal stability of vibratory cylindrical gyroscopes.

  8. ICRF heated enhanced performance modes and mode conversion electron heating in alcator C-mod

    Energy Technology Data Exchange (ETDEWEB)

    Takase, Y.; Golovato, S.; Porkolab, M.; Boivin, R.; Bombarda, F.; Bonoli, P.; Fiore, C.; Garnier, D.; Goetz, J.; Graf, M.; Granetz, R.; Greenwald, M.; Horne, S.; Hubbard, A.; Hutchinson, I.; Irby, J.; LaBombard, B.; Lipschultz, B.; Majeski, R.; Marmar, E.; May, M.; Mazurenko, A.; McCracken, G.; OShea, P.; Pinsker, R.; Reardon, J.; Rice, J.; Rost, C.; Snipes, J.; Terry, J.; Watterson, R.; Welch, B.; Wolfe, S. [MIT Plasma Fusion Center, Cambridge, Massachusetts 02139 (United States)

    1996-02-01

    D(H) minority heating experiments were performed at {ital B}{sub {ital T}}=5.3 T with up to 3.5 MW of RF power. The highest stored energy of 130 kJ was achieved in an ELM-free H-mode plasma. The H-mode power threshold is roughly consistent with the ITER scaling, {ital P}/{ital S}=0.044{bar {ital n}}{sub {ital eB}}{sub {ital T}}, but H-modes have been obtained at power levels as much as a factor of two below this scaling. H-factors of up to 1.5 have been observed in ELM-free H-mode plasmas. The highest fusion reactivity of 9{times}10{sup 13} sec{sup {minus}1} was obtained in a PEP H-mode plasma with lithium pellet injection and on-axis ICRF heating. These discharges are characterized by highly peaked density and ion temperature profiles, with fusion reactivity enhanced by typically an order of magnitude above similar L-mode discharges. Effective localized direct electron heating by mode converted IBW was observed in H-{sup 3}He plasmas (analogous to D-T plasmas) at 6.5 T. {copyright} {ital 1996 American Institute of Physics.}

  9. Vibrational relaxation pathways of AI and AII modes in N-methylacetamide clusters

    NARCIS (Netherlands)

    Piatkowski, L.; Bakker, H.J.

    2010-01-01

    We studied the pathways of vibrational energy relaxation of the amide I (~1660 cm-1) and amide II (~1560 cm-1) vibrational modes of N-methylacetamide (NMA) in CCl4 solution using two-color femtosecond vibrational spectroscopy. We measured the transient spectral dynamics upon excitation of each of

  10. Deviations of frequency and the mode of vibration of commercially available whole-body vibration training devices.

    Science.gov (United States)

    Kaeding, T S

    2015-06-01

    Research in the field of whole body vibration (WBV) training and the use of it in practice might be hindered by the fact that WBV training devices generate and transmit frequencies and/or modes of vibration which are different to preset adjustments. This research project shall clarify how exact WBV devices apply the by manufacturer information promised preset frequency and mode of vibration. Nine professional devices for WBV training were tested by means of a tri-axial accelerometer. The accelerations of each device were recorded under different settings with a tri-axial accelerometer. Beneath the measurement of different combinations of preset frequency and amplitude the repeatability across 3 successive measurements with the same preset conditions and one measurement under loaded condition were carried out. With 3 exceptions (both Board 3000 & srt medical PRO) we did not find noteworthy divergences between preset and actual applied frequencies. In these 3 devices we found divergences near -25%. Loading the devices did not affect the applied frequency or mode of vibration. There were no important divergences measurable for the applied frequency and mode of vibration regarding repeatability. The results of our measurements cannot be generalized as we only measured one respectively at most two devices of one model in terms of a random sample. Based on these results we strongly recommend that user in practice and research should analyse their WBV training devices regarding applied frequency and mode of vibration.

  11. The Assistance of Molecular Vibrations on Coherent Energy Transfer in Photosynthesis from the View of Quantum Heat Engine

    CERN Document Server

    Zhang, Zhedong

    2015-01-01

    Recently the quantum nature in the energy transport in solar cell and light-harvesting complexes have attracted much attention, as being triggered by the experimental observations. We model the light-harvesting complex (i.e., PEB50 dimer) as a quantum heat engine (QHE) and study the effect of the undamped intra-molecule vibrational modes on the coherent energy transfer process and quantum transport. We find that the exciton-vibration interaction has non-trivial contribution to the promotion of quantum yield as well as transport properties of the quantum heat engine at steady state, by enhancing the quantum coherence quantified by entanglement entropy. The perfect quantum yield over 90% has been obtained, with theexciton-vibration coupling. We attribute these improvements to the renormalization of the electronic couplings effectively induced by exciton-vibration interaction and the subsequent delocalization of excitons. Finally we demonstrate that the thermal relaxation and dephasing can help the excitation en...

  12. A search for the dominant heat conducting phonon modes in graphene: An atomistic simulation study

    Science.gov (United States)

    Zhang, Hengji; Cho, Kyeongjae

    2011-03-01

    We have performed an equilibrium molecular dynamic (MD) simulation study to investigate phonon thermal transport in graphene at 300K with Green-Kubo method. Using a newly optimized reactive empirical bond order carbon potential (Lindsay, et al. Physical Review B 81, 205441, 2010), our calculated thermal conductivity (TC) of defect free graphene is about 3000 W/mK in good agreement with experiments(~ 3000-5000 W/mK). A maximum of ~ 1000 fold reduction in TC is possible to achieve for graphene with defects and surrounding viscous medium. As we decompose the in-plane and out-plane phonon vibration modes of graphene in MD simulations, the out of plane vibration modes (ZA phonon) contribute to about 50% of the overall TC. This large contribution from ZA modes is explained with density of states analysis. We have clarified a recent controversy on which polarization mode in graphene is the main heat carrier.

  13. The influence of longitudinal vibrations on the heat transfer performance of inclined heat pipes

    Directory of Open Access Journals (Sweden)

    Rong-Horng Chen

    2015-02-01

    Full Text Available This study focused on investigating the influence of longitudinal vibrations, the condensation section temperature, and the inclination angles on the heat transfer performance of grooved cylindrical copper heat pipes with lengths of 600 and 150 mm and an outer diameter of 8 mm. The inclination angles of the tested heat pipes were 0°, ±45°, and ±90°. Longitudinal vibrations with frequencies of 3, 4, 5, 6, and 9 Hz and amplitudes of 2.8, 5, 10, 15, 20, and 25 mm, which resulted in accelerations between 0.1 and 1.01 g, were experimentally tested. The condensation section temperatures were set at 20°C, 30°C, and 40°C. A heating jacket and a cooling sleeve were installed at the evaporation and condensation sections of the test cell to simulate a constant heat flux and a constant temperature boundary, respectively. The results showed that with the heat pipe placed with the condensation section on top and the evaporation section on bottom, a fairly low and constant thermal resistance (approximately 0.25 K/W for the 600-mm heat pipe and 0.75–1.2 K/W for the 150-mm heat pipe was obtained, both with and without heat pipe vibration and regardless of the condensation section temperature.

  14. Dissociative electron attachment and vibrational excitation of CF{sub 3}Cl: Effect of two vibrational modes revisited

    Energy Technology Data Exchange (ETDEWEB)

    Tarana, Michal [Department of Physics and Astronomy, University of Nebraska, Lincoln, Nebraska 68588 (United States); JILA, University of Colorado and NIST, Boulder, Colorado 80309-0440 (United States); Houfek, Karel; Horacek, Jiri [Institute of Theoretical Physics, Faculty of Mathematics and Physics, Charles University in Prague, V Holesovickach 2, Prague (Czech Republic); Fabrikant, Ilya I. [Department of Physics and Astronomy, University of Nebraska, Lincoln, Nebraska 68588 (United States); Department of Physics and Astronomy, Open University, Walton Hall, Milton Keynes MK7 6AA (United Kingdom)

    2011-11-15

    We present a study of dissociative electron attachment and vibrational excitation processes in electron collisions with the CF{sub 3}Cl molecule. The calculations are based on the two-dimensional nuclear dynamics including the C-Cl symmetric stretch coordinate and the CF{sub 3} symmetric deformation (umbrella) coordinate. The complex potential energy surfaces are calculated using the ab initio R-matrix method. The results for dissociative attachment and vibrational excitation of the umbrella mode agree quite well with experiment whereas the cross section for excitation of the C-Cl symmetric stretch vibrations is about a factor-of-three too low in comparison with experimental data.

  15. Multiscale studies on the nonlinear vibration of delaminated composite laminates-global vibration mode with micro buckles on the interfaces.

    Science.gov (United States)

    Xue, Jianghong; Xia, Fei; Ye, Jun; Zhang, Jianwen; Chen, Shuhua; Xiong, Ying; Tan, Zuyuan; Liu, Renhuai; Yuan, Hong

    2017-06-30

    This paper presents a multiscale approach to study the nonlinear vibration of fiber reinforced composite laminates containing an embedded, through-width delamination dividing the laminate into four sub-laminates. The equations of motion are established from macroscopic nonlinear mechanics for plates and shells and micro-mechanics of composite material to allow for the influences of large amplitude, membrane stretching in the neutral plane, and the interactions of the sublaminates. Analytical solutions obtained in this paper reveal that the interaction penalty at the interfaces plays a coupling effect between sublaminates, which eventually alters the vibration characters of the four-sublaminate lamina in macroscopic and microscopic mechanism. From a macro perspective, sub-laminates above and below the delamination vibrate in exactly the same mode in spite of their different stiffness and the four-sublaminate lamina has a consistent global vibration mode. In accompanying with the macro vibration, micro buckles occur on the interfaces of the delamination with amplitude about 10(-3) times of that of the global mode. It is found that the vibration frequency is an eigenvalue of the delaminated lamina determined only by the geometry of the delamination. Authentication of the multiscale study is fulfilled by comparing the analytical solutions with the FEA results.

  16. Vibration damping and heat transfer using material phase changes

    Science.gov (United States)

    Kloucek, Petr [Houston, TX; Reynolds, Daniel R [Oakland, CA

    2009-03-24

    A method and apparatus wherein phase changes in a material can dampen vibrational energy, dampen noise and facilitate heat transfer. One embodiment includes a method for damping vibrational energy in a body. The method comprises attaching a material to the body, wherein the material comprises a substrate, a shape memory alloy layer, and a plurality of temperature change elements. The method further comprises sensing vibrations in the body. In addition, the method comprises indicating to at least a portion of the temperature change elements to provide a temperature change in the shape memory alloy layer, wherein the temperature change is sufficient to provide a phase change in at least a portion of the shape memory alloy layer, and further wherein the phase change consumes a sufficient amount of kinetic energy to dampen at least a portion of the vibrational energy in the body. In other embodiments, the shape memory alloy layer is a thin film. Additional embodiments include a sensor connected to the material.

  17. Vibration damping and heat transfer using material phase changes

    Science.gov (United States)

    Kloucek, Petr (Inventor); Reynolds, Daniel R. (Inventor)

    2009-01-01

    A method and apparatus wherein phase changes in a material can dampen vibrational energy, dampen noise and facilitate heat transfer. One embodiment includes a method for damping vibrational energy in a body. The method comprises attaching a material to the body, wherein the material comprises a substrate, a shape memory alloy layer, and a plurality of temperature change elements. The method further comprises sensing vibrations in the body. In addition, the method comprises indicating to at least a portion of the temperature change elements to provide a temperature change in the shape memory alloy layer, wherein the temperature change is sufficient to provide a phase change in at least a portion of the shape memory alloy layer, and further wherein the phase change consumes a sufficient amount of kinetic energy to dampen at least a portion of the vibrational energy in the body. In other embodiments, the shape memory alloy layer is a thin film. Additional embodiments include a sensor connected to the material.

  18. Vibrational modes of the Cu(100)-c(2x2)-Pd surface

    DEFF Research Database (Denmark)

    Stoltze, Per; Hannon, J.B.; Ibach, H.

    1996-01-01

    The vibrational modes of the surface have been measured using electron-energy loss spectroscopy. The measured mode energies are compared to dynamical models with parameters taken from effective medium theory. Strong Pd-Cu interplanar bonding gives rise to nearly degenerate Pd and Cu vibrations (95...... cm(-1)) at the (X) over bar point, despite the large mass difference of the ions. Upon low-temperature annealing of the surface, overlayer islands of pure Cu coalesce and order. These overlayer islands are characterized by a high-energy vibrational mode near 128 cm(-1) which grows in intensity upon...

  19. The diffraction signatures of individual vibrational modes in polyatomic molecules

    Science.gov (United States)

    Ryu, Seol; Weber, Peter M.; Stratt, Richard M.

    2000-01-01

    Though one normally thinks of single-molecule diffraction studies as tools for eliciting molecular geometry, molecular diffraction patterns are really the Fourier transforms of complete molecular wave functions. There is thus at least the possibility of imaging the vibrational wave functions of polyatomic molecules by means of a pump-probe diffraction experiment: the pump laser could prepare a specific vibrational state and an electron or x-ray could then be diffracted off the molecule some short time later. The present paper develops the general theory of diffraction signatures for individual vibrational wave functions in polyatomic molecules and investigates the feasibility of seeing such signatures experimentally using the example of a linear triatomic molecule modeled after CS2. Although aligned molecules in specific vibrational quantum states turn out to exhibit very characteristic diffraction signatures, the signatures of the vibrational wave functions are partially washed out for the complete isotropy expected from gas phase molecules. Nonetheless, it is possible to design a diffraction experiment using a pump-dump sequence with a polarized laser beam which will select a nonisotropic sample of vibrationally excited molecules. We show that the resulting level of anisotropy should enhance the diffraction signature, helping to distinguish different vibrational components. These model calculations therefore suggest the possibility of observing the dynamics of vibrational wave packets using experimentally realizable diffraction techniques.

  20. Vibration Mode Observation of Piezoelectric Disk-type Resonator by High Frequency Laser Doppler Vibrometer

    Science.gov (United States)

    Matsumura, Takeshi; Esashi, Masayoshi; Harada, Hiroshi; Tanaka, Shuji

    For future mobile phones based on cognitive radio technology, a compact multi-band RF front-end architecture is strongly required and an integrated multi-band RF filter bank is a key component in it. Contour-mode resonators are receiving increased attention for a multi-band filter solution, because its resonant frequency is mainly determined by its size and shape, which are defined by lithography. However, spurious responses including flexural vibration are also excited due to its thin structure. To improve resonator performance and suppress spurious modes, visual observation with a laser probe system is very effective. In this paper, we have prototyped a mechanically-coupled disk-array filter, which consists of a Si disk and 2 disk-type resonators of higher-order wine-glass mode, and observed its vibration modes using a high-frequency laser-Doppler vibrometer (UHF-120, Polytec, Inc.). As a result, it was confirmed that higher order wine-glass mode vibration included a compound displacement, and that its out-of-plane vibration amplitude was much smaller than other flexural spurious modes. The observed vibration modes were compared with FEM (Finite Element Method) simulation results. In addition, it was also confirmed that the fabrication error, e.g. miss-alignment, induced asymmetric vibration.

  1. Vibrational relaxation in simulated two-dimensional infrared spectra of two amide modes in solution

    NARCIS (Netherlands)

    Dijkstra, Arend G.; Jansen, Thomas la Cour; Bloem, Robbert; Knoester, Jasper

    2007-01-01

    Two-dimensional infrared spectroscopy is capable of following the transfer of vibrational energy between modes in real time. We develop a method to include vibrational relaxation in simulations of two-dimensional infrared spectra at finite temperature. The method takes into account the correlated

  2. Precise Ab-initio prediction of terahertz vibrational modes in crystalline systems

    DEFF Research Database (Denmark)

    Jepsen, Peter Uhd; Clark, Stewart J.

    2007-01-01

    We use a combination of experimental THz time-domain spectroscopy and ab-initio density functional perturbative theory to accurately predict the terahertz vibrational spectrum of molecules in the crystalline phase. Our calculations show that distinct vibrational modes found in solid-state materials...

  3. Blade Vibration Measurement System for Characterization of Closely Spaced Modes and Mistuning Project

    Data.gov (United States)

    National Aeronautics and Space Administration — There are several ongoing challenges in non-contacting blade vibration and stress measurement systems that can address closely spaced modes and blade-to-blade...

  4. Experimental study of heat transfer enhancement due to the surface vibrations in a flexible double pipe heat exchanger

    Science.gov (United States)

    Hosseinian, A.; Meghdadi Isfahani, A. H.

    2017-11-01

    In this study, the heat transfer enhancement due to the surface vibration for a double pipe heat exchanger, made of PVDF, is investigated. In order to create forced vibrations (3-9 m/s2, 100 Hz) on the outer surface of the heat exchanger electro-dynamic vibrators are used. Experiments were performed at inner Reynolds numbers ranging from 2533 to 9960. The effects of volume flow rate and temperature on heat transfer performance are evaluated. Results demonstrated that heat transfer coefficient increases by increasing vibration level and mass flow rate. The most increase in heat transfer coefficient is 97% which is obtained for the highest vibration level (9 m/s2) in the experiment range.

  5. Nanoantenna-assisted plasmonic enhancement of IR absorption of vibrational modes of organic molecules

    Directory of Open Access Journals (Sweden)

    Alexander G. Milekhin

    2017-05-01

    Full Text Available Nanoantenna-assisted plasmonic enhancement of IR absorption and Raman scattering was employed for studying the vibrational modes in organic molecules. Ultrathin cobalt phthalocyanine films (3 nm were deposited on Au nanoantenna arrays with specified structural parameters. The deposited organic films reveal the enhancement of both Raman scattering and IR absorption vibrational modes. To extend the possibility of implementing surface-enhanced infrared absorption (SEIRA for biological applications, the detection and analysis of the steroid hormone cortisol was demonstrated.

  6. Acoustic vibration modes and electron-lattice coupling in self-assembled silver nanocolumns.

    Science.gov (United States)

    Burgin, J; Langot, P; Arbouet, A; Margueritat, J; Gonzalo, J; Afonso, C N; Vallée, F; Mlayah, A; Rossell, M D; Van Tendeloo, G

    2008-05-01

    Using ultrafast spectroscopy, we investigated electron-lattice coupling and acoustic vibrations in self-assembled silver nanocolumns embedded in an amorphous Al2O3 matrix. The measured electron-lattice energy exchange time is smaller in the nanocolumns than in bulk silver, with a value very close to that of isolated nanospheres with comparable surface to volume ratio. Two vibration modes were detected and ascribed to the breathing and extensional mode of the nanocolumns, in agreement with numerical simulations.

  7. Vibrational relaxation of the H2O bending mode in liquid water.

    Science.gov (United States)

    Larsen, Olaf F A; Woutersen, Sander

    2004-12-22

    We have studied the vibrational relaxation of the H(2)O bending mode in an H(2)O:HDO:D(2)O isotopic mixture using infrared pump-probe spectroscopy. The transient spectrum and its delay dependence reveal an anharmonic shift of 55+/-10 cm(-1) for the H(2)O bending mode, and a value of 400+/-30 fs for its vibrational lifetime. (c) 2004 American Institute of Physics.

  8. Modeling and analysis of circular flexural-vibration-mode piezoelectric transformer.

    Science.gov (United States)

    Huang, Yihua; Huang, Wei

    2010-12-01

    We propose a circular flexural-vibration-mode piezoelectric transformer and perform a theoretical analysis of the transformer. An equivalent circuit is derived from the equations of piezoelectricity and the Hamilton's principle. With this equivalent circuit, the voltage gain ratio, input impedance, and the efficiency of the circular flexural-vibration-mode piezoelectric transformer can be determined. The basic behavior of the transformer is shown by numerical results.

  9. Extended and localized vibrational modes in (1-3) Penrose-like piezocomposites

    Science.gov (United States)

    Montero de Espinosa, F.; Torres, M.

    1994-09-01

    Acoustic vibrational modes of piezocomposites with ceramic bars arranged at the vertices of both perfect Penrose tilings and random Penrose tilings have directly been observed by recording the corresponding standing vibration amplitude pattern. The random Penrose tiling exhibits similar although smoother spectrum than the perfect Penrose one. For both structures, the existence of extended and localized modes is shown. Resonances frequencies at the edges of the spectrum pseudogap correspond to localized and highly entropic modes. As expected, the modes are more localized in the random Penrose tiling case.

  10. Assistance of molecular vibrations on coherent energy transfer in photosynthesis from the view of a quantum heat engine.

    Science.gov (United States)

    Zhang, Zhedong; Wang, Jin

    2015-04-02

    Recently, the quantum nature in the energy transport in solar cells and light-harvesting complexes has attracted much attention as being triggered by the experimental observations. We model the light-harvesting complex (i.e., PEB50 dimer) as a quantum heat engine (QHE) and study the effect of the undamped intramolecule vibrational modes on the coherent energy-transfer process and quantum transport. We find that the exciton-vibration interaction has nontrivial contribution to the promotion of quantum yield as well as transport properties of the QHE at steady state by enhancing the quantum coherence quantified by entanglement entropy. The perfect quantum yield over 90% has been obtained, with the exciton-vibration coupling. We attribute these improvements to the renormalization of the electronic couplings effectively induced by exciton-vibration interaction and the subsequent delocalization of excitons. Finally, we demonstrate that the thermal relaxation and dephasing can help the excitation energy transfer in the PEB50 dimer.

  11. Component mode synthesis and large deflection vibration of complex structures. Volume 3: Multiple-mode nonlinear free and forced vibrations of beams using finite element method

    Science.gov (United States)

    Mei, Chuh; Shen, Mo-How

    1987-01-01

    Multiple-mode nonlinear forced vibration of a beam was analyzed by the finite element method. Inplane (longitudinal) displacement and inertia (IDI) are considered in the formulation. By combining the finite element method and nonlinear theory, more realistic models of structural response are obtained more easily and faster.

  12. Coupling between flexural modes in free vibration of single-walled carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Rumeng; Wang, Lifeng, E-mail: walfe@nuaa.edu.cn [State Key Laboratory of Mechanics and Control of Mechanical Structures, Nanjing University of Aeronautics and Astronautics, 210016 Nanjing (China)

    2015-12-15

    The nonlinear thermal vibration behavior of a single-walled carbon nanotube (SWCNT) is investigated by molecular dynamics simulation and a nonlinear, nonplanar beam model. Whirling motion with energy transfer between flexural motions is found in the free vibration of the SWCNT excited by the thermal motion of atoms where the geometric nonlinearity is significant. A nonlinear, nonplanar beam model considering the coupling in two vertical vibrational directions is presented to explain the whirling motion of the SWCNT. Energy in different vibrational modes is not equal even over a time scale of tens of nanoseconds, which is much larger than the period of fundamental natural vibration of the SWCNT at equilibrium state. The energy of different modes becomes equal when the time scale increases to the microsecond range.

  13. Coupling between flexural modes in free vibration of single-walled carbon nanotubes

    Directory of Open Access Journals (Sweden)

    Rumeng Liu

    2015-12-01

    Full Text Available The nonlinear thermal vibration behavior of a single-walled carbon nanotube (SWCNT is investigated by molecular dynamics simulation and a nonlinear, nonplanar beam model. Whirling motion with energy transfer between flexural motions is found in the free vibration of the SWCNT excited by the thermal motion of atoms where the geometric nonlinearity is significant. A nonlinear, nonplanar beam model considering the coupling in two vertical vibrational directions is presented to explain the whirling motion of the SWCNT. Energy in different vibrational modes is not equal even over a time scale of tens of nanoseconds, which is much larger than the period of fundamental natural vibration of the SWCNT at equilibrium state. The energy of different modes becomes equal when the time scale increases to the microsecond range.

  14. Heat Transfer of Mesh-wick Heat-pipes : Bottom Heat Mode

    OpenAIRE

    IKEDA, Yoshio; ONUMA, Sadayuki

    1988-01-01

    A heat-pipe in which the working fluid circulates by gravity need not contain a wick. this type of heat pipe can be examined as a thermo-siphon. For better moistening inside the evaporating zone and improvement of the limit of flooding or entrainment, wicks of groove type are often used. In the present study, the performance of the metal wick of the copper-ethanol heat-pipe is examined by investigating the effect of inclination angle and volume of enclosed fluid on thermal resistance. In mode...

  15. Free vibrations of an arbitrary structure in terms of component modes.

    Science.gov (United States)

    Dowell, E. H.

    1972-01-01

    A method for the analysis of the free vibrations of an arbitrary structure in terms of component modes is presented based upon the use of the normal, free-free modes of the components in a Rayleigh-Ritz analysis with the constraint or continuity conditions

  16. Interactions between directly- and parametrically-driven vibration modes in a micromechanical resonator

    NARCIS (Netherlands)

    Westra, H.J.R.; Karabacak, D.M.; Brongersma, S.H.; Crego-Calama, M.; Van der Zant, H.S.J.; Venstra, W.J.

    2011-01-01

    The interactions between parametrically- and directly-driven vibration modes of a clamped-clamped beam resonator are studied. An integrated piezoelectric transducer is used for direct and parametric excitation. First, the parametric amplification and oscillation of a single mode are analyzed by the

  17. Mode selection of modal expansion method estimating vibration field of washing machine

    Science.gov (United States)

    Jung, B. K.; Jeong, W. B.

    2015-03-01

    This paper is about a study estimating the vibration and radiated noise of a washing machine by using a mode selection-applied modal expansion method (MEM). MEM is a technique that identifies the vibration field from a portion of eigenvectors (or mode shapes) of a structure, and thus, the selection of the eigenvectors has a big impact on the vibration results identified. However, there have been few studies about selecting the eigenvectors with respect to the structural vibration and radiated noise estimation. Accordingly, this paper proposes the use of a new mode selection method to identify the vibration based on the MEM and then calculate radiated noise of a washing machine. The results gained from the experiment were also compared. The vibration and noise results of numerical analysis using the proposed selection method are in line with the measured results. The selection method proposed in this paper corresponds well with the MEM and this process seems to be applicable to the estimation of various structure vibrations and radiated noise.

  18. Oxidizer heat exchangers for rocket engine operation in idle modes

    Science.gov (United States)

    Kanic, P. G.; Kmiec, T. D.

    1987-01-01

    The heat exchanger concept is discussed together with its role in rocket engine operation in idle modes. Two heat exchanger designs (low and high heat transfer) utilizing different approaches to achieve stable oxygen vaporization are presented as well as their performance test results. It is concluded that compact and lightweight heat exchangers can be used in a stable manner under the 'idle' operating conditions expected with the RL10 rocket engine.

  19. A Pictorial Visualization of Normal Mode Vibrations of the Fullerene (C[subscript 60]) Molecule in Terms of Vibrations of a Hollow Sphere

    Science.gov (United States)

    Dunn, Janette L.

    2010-01-01

    Understanding the normal mode vibrations of a molecule is important in the analysis of vibrational spectra. However, the complicated 3D motion of large molecules can be difficult to interpret. We show how images of normal modes of the fullerene molecule C[subscript 60] can be made easier to understand by superimposing them on images of the normal…

  20. Aerial Ultrasonic Source Using Stripe-Mode Transverse Vibrating Plate with Jutting Driving Point

    Science.gov (United States)

    Miura, Hikaru; Ishikawa, Hitoshi

    2009-07-01

    Ultrasonic sources using a stripe-mode rectangular transverse vibrating plate have been used as acoustic sources emitting intense acoustic waves in air. Because these sources are based on the resonance of transverse vibration, their electric-acoustic conversion rate is as high as 90%, which is a merit. In this study, a vibrating plate with a unique shape was developed to enhance the effectiveness of acoustic sources. It is called a stripe-mode transverse vibrating plate with a jutting driving point. The advantage of this plate shape is that the acoustic source does not interfere with the emission of acoustic waves since the driving point is outside the plate, and there is no need to distinguish between the front and back sides of the vibrating plate. The conditions effective for driving the stripe-mode transverse vibrating plate were clarified. That is, the length of the side parallel to the node lines of the plate is an odd number times the length between the nodes in the stripe mode, and the length of the side perpendicular is at least 6 times but not a multiple of 3 greater than or equal to 15 times, subtracted by 0.5 times, the length between the nodes. Moreover, the length between the driving point and the edge of the plate is a positive integer with a noninteger value of 0.9.

  1. Sprinkled Heat Exchangers in Evaporation Mode

    Directory of Open Access Journals (Sweden)

    Pospisil J.

    2013-04-01

    Full Text Available The paper presents research on the heat transfer at sprinkled tube bundles situated in a test chamber at atmospheric pressure and low-pressure. Dynamic effects of physical quantities influencing the heat transfer coefficient during boiling are examined experimentally. Experimental results were achieved by means of balance measuring using thermocouple probes and by analysis of thermal diagrams created during operation periods.

  2. Localization of natural modes of vibration in bladed disks

    Science.gov (United States)

    Bendiksen, O. O.; Valero, N. A.

    1987-01-01

    A study is presented of the mode localization phenomenon in imperfect blade-disk and blade-shroud-disk assemblies. The results indicate that unshrouded blades mounted on stiff disks are especially susceptible, and even small blade imperfections within manufacturing tolerances are likely to trigger mode localization. Increasing the interblade coupling by adding shrouds or reducing the disk stiffness greatly reduces the localization susceptiblity, although certain modes may still become localized if the shrouds are free to slip.

  3. Finite-temperature hydrogen adsorption and desorption thermodynamics driven by soft vibration modes.

    Science.gov (United States)

    Woo, Sung-Jae; Lee, Eui-Sup; Yoon, Mina; Kim, Yong-Hyun

    2013-08-09

    It has been widely accepted that enhanced dihydrogen adsorption is required for room-temperature hydrogen storage on nanostructured porous materials. Here we report, based on results of first-principles total energy and vibrational spectrum calculations, finite-temperature adsorption and desorption thermodynamics of hydrogen molecules that are adsorbed on the metal center of metal-porphyrin-incorporated graphene. We have revealed that the room-temperature hydrogen storage is achievable not only with the enhanced adsorption enthalpy, but also with soft-mode driven vibrational entropy of the adsorbed dihydrogen molecule. The soft vibration modes mostly result from multiple orbital coupling between the hydrogen molecule and the buckled metal center, for example, in Ca-porphyrin-incorporated graphene. Our study suggests that the current design strategy for room-temperature hydrogen storage materials should be modified with explicitly taking the finite-temperature vibration thermodynamics into account.

  4. A study of the eigenvectors of the low-frequency vibrational modes in crystalline adenosine via high pressure Raman spectroscopy.

    Science.gov (United States)

    Lee, Scott A; Pinnick, David A; Anderson, A

    2014-12-01

    High-pressure Raman spectroscopy has been used to study the eigenvectors and eigenvalues of the vibrational modes of crystalline adenosine at 295 K by evaluating the logarithmic derivative of the vibrational frequency with respect to pressure: [Formula: see text]. Crystalline samples of molecular materials such as adenosine will have vibrational modes that are localized within a molecular unit ("internal" modes) as well as modes in which the molecular units vibrate against each other ("external" modes). The value of the logarithmic derivative is found to be a diagnostic probe of the nature of the eigenvector of the vibrational modes. Stretching modes which are predominantly internal to the molecule have low logarithmic derivatives while external modes have higher logarithmic derivatives. Particular interest is paid to the low-frequency (≤150 cm(-1)) modes. Based on the pressure dependence of its logarithmic derivative, a mode near 49 cm(-1) is identified as internal mode. The other modes below 400 cm(-1) have pressure dependences of their logarithmic derivatives consistent with being either (1) modes which are mainly external, meaning that the molecules of the unit cell vibrate against each other in translational or librational motions (or linear combinations thereof), or (2) torsional or bending modes involving a large number of atoms, mainly within a molecule. The modes above 400 cm(-1) all have pressure dependences of their logarithmic derivatives consistent with being mainly internal modes.

  5. Subfemtosecond steering of hydrocarbon deprotonation through superposition of vibrational modes

    Science.gov (United States)

    Alnaser, A. S.; Kübel, M.; Siemering, R.; Bergues, B.; Kling, Nora G.; Betsch, K. J.; Deng, Y.; Schmidt, J.; Alahmed, Z. A.; Azzeer, A. M.; Ullrich, J.; Ben-Itzhak, I.; Moshammer, R.; Kleineberg, U.; Krausz, F.; de Vivie-Riedle, R.; Kling, M. F.

    2014-05-01

    Subfemtosecond control of the breaking and making of chemical bonds in polyatomic molecules is poised to open new pathways for the laser-driven synthesis of chemical products. The break-up of the C-H bond in hydrocarbons is an ubiquitous process during laser-induced dissociation. While the yield of the deprotonation of hydrocarbons has been successfully manipulated in recent studies, full control of the reaction would also require a directional control (that is, which C-H bond is broken). Here, we demonstrate steering of deprotonation from symmetric acetylene molecules on subfemtosecond timescales before the break-up of the molecular dication. On the basis of quantum mechanical calculations, the experimental results are interpreted in terms of a novel subfemtosecond control mechanism involving non-resonant excitation and superposition of vibrational degrees of freedom. This mechanism permits control over the directionality of chemical reactions via vibrational excitation on timescales defined by the subcycle evolution of the laser waveform.

  6. A high pressure study of the eigenvectors of the infra-red active vibrational modes of crystalline adenosine.

    Science.gov (United States)

    Starkey, Carl A; Lee, Scott A; Anderson, Anthony

    2016-01-01

    High-pressure infrared spectroscopy has been used to study the eigenvectors and eigenvalues of the vibrational modes of crystalline adenosine at 298 K by evaluating the logarithmic derivative of the vibrational frequency with respect to pressure: [Formula: see text]. Crystalline samples of molecular materials such as adenosine have vibrational modes that are localized within a molecular unit ("internal" modes) as well as modes in which the molecular units vibrate against each other ("external" modes). The value of the logarithmic derivative is that it is a diagnostic probe of the nature of the eigenvector of these vibrational modes. Stretching modes, which are predominantly internal to the molecule, have low logarithmic derivatives while external modes have higher logarithmic derivatives. Particular attention is paid to modes in the 800-1000 cm(-1) range since modes in that region of the vibrational spectrum are found to be sensitive to the conformation of double-helical DNA. Since the sugar pucker is different for the various conformations of DNA, this fact suggests that these modes involve the motion of atoms in the sugar group. The vibrations of the hydrogen atoms are also of interest to study since the vibrational frequency of hydrogen atoms involved in hydrogen bonds has a negative pressure derivative. Such behavior clearly shows which hydrogen atoms are involved in hydrogen bonding.

  7. Electron-Beam Mapping of Vibrational Modes with Nanometer Spatial Resolution.

    Science.gov (United States)

    Dwyer, C; Aoki, T; Rez, P; Chang, S L Y; Lovejoy, T C; Krivanek, O L

    2016-12-16

    We demonstrate that a focused beam of high-energy electrons can be used to map the vibrational modes of a material with a spatial resolution of the order of one nanometer. Our demonstration is performed on boron nitride, a polar dielectric which gives rise to both localized and delocalized electron-vibrational scattering, either of which can be selected in our off-axial experimental geometry. Our experimental results are well supported by our calculations, and should reconcile current controversy regarding the spatial resolution achievable in vibrational mapping with focused electron beams.

  8. Efficient vibration mode analysis of aircraft with multiple external store configurations

    Science.gov (United States)

    Karpel, M.

    1988-01-01

    A coupling method for efficient vibration mode analysis of aircraft with multiple external store configurations is presented. A set of low-frequency vibration modes, including rigid-body modes, represent the aircraft. Each external store is represented by its vibration modes with clamped boundary conditions, and by its rigid-body inertial properties. The aircraft modes are obtained from a finite-element model loaded by dummy rigid external stores with fictitious masses. The coupling procedure unloads the dummy stores and loads the actual stores instead. The analytical development is presented, the effects of the fictitious mass magnitudes are discussed, and a numerical example is given for a combat aircraft with external wing stores. Comparison with vibration modes obtained by a direct (full-size) eigensolution shows very accurate coupling results. Once the aircraft and stores data bases are constructed, the computer time for analyzing any external store configuration is two to three orders of magnitude less than that of a direct solution.

  9. Electronic Properties of Si-Hx Vibrational Modes at Si Waveguide Interface.

    Science.gov (United States)

    Bashouti, Muhammad Y; Yousefi, Peyman; Ristein, Jürgen; Christiansen, Silke H

    2015-10-01

    Attenuated total reflectance (ATR) and X-ray photoelectron spectroscopy in suite with Kelvin probe were conjugated to explore the electronic properties of Si-Hx vibrational modes by developing Si waveguide with large dynamic detection range compared with conventional IR. The Si 2p emission and work-function related to the formation and elimination of Si-Hx bonds at Si surfaces are monitored based on the detection of vibrational mode frequencies. A transition between various Si-Hx bonds and thus related vibrational modes is monitored for which effective momentum transfer could be demonstrated. The combination of the aforementioned methods provides for results that permit a model for the kinetics of hydrogen termination of Si surfaces with time and advanced surface characterizing of hybrid-terminated semiconducting solids.

  10. A nonlinear multi-mode wideband piezoelectric vibration-based energy harvester using compliant orthoplanar spring

    Energy Technology Data Exchange (ETDEWEB)

    Dhote, Sharvari, E-mail: sharvari.dhote@mail.utoronto.ca; Zu, Jean; Zhu, Yang [Department of Mechanical and Industrial Engineering, University of Toronto, 5 King' s College Road, Toronto, Ontario M5S-3G8 (Canada)

    2015-04-20

    In this paper, a nonlinear wideband multi-mode piezoelectric vibration-based energy harvester (PVEH) is proposed based on a compliant orthoplanar spring (COPS), which has an advantage of providing multiple vibration modes at relatively low frequencies. The PVEH is made of a tri-leg COPS flexible structure, where three fixed-guided beams are capable of generating strong nonlinear oscillations under certain base excitation. A prototype harvester was fabricated and investigated through both finite-element analysis and experiments. The frequency response shows multiple resonance which corresponds to a hardening type of nonlinear resonance. By adding masses at different locations on the COPS structure, the first three vibration modes are brought close to each other, where the three hardening nonlinear resonances provide a wide bandwidth for the PVEH. The proposed PVEH has enhanced performance of the energy harvester in terms of a wide frequency bandwidth and a high-voltage output under base excitations.

  11. 2-Chloro- and 2-bromo-3-pyridinecarboxaldehydes: structures, rotamers, fermi resonance and vibration modes.

    Science.gov (United States)

    Yenagi, Jayashree; Shettar, Anita; Tonannavar, J

    2011-09-01

    FT-Infrared (4000-400 cm(-1)) and NIR-FT-Raman (4000-50 cm(-1)) spectral measurements have been made for 2-chloro- and 2-bromo-3-pyridinecarboxaldehydes. A DFT vibration analysis at B3LYP/6-311++G (d,p) level, valence force-fields and vibrational mode calculations have been performed. Aided by very good agreement between observed and computed vibration spectra, a complete assignment of fundamental vibration modes to the observed absorptions and Raman bands has been proposed. Orientations of the aldehydic group have produced two oblate asymmetric rotamers for each molecule, ON-trans and ON-cis: the ON-trans rotamer being more stable than cis by 3.42 kcal mol(-1) for 2-chloro-3-pyridinecarboxaldehyde and 3.68 kcal mol(-1) for 2-bromo-3-pyridinecarboxaldehyde. High potential energy barrier ca 14 kcal/mol, induced by steric hindrance, restricts rotamers' population to ON-trans only. It is observed that, in the presence of bromine, C-H stretching modes are pronounced; a missing characteristic ring mode in chlorine's presence shows at 1557 cm(-1); the characteristic ring mode at 1051 cm(-1) is diminished; a mixed mode near 707 cm(-1) is enhanced. Further, an observed doublet near 1696-1666 cm(-1) in both IR and Raman spectra is explained on the basis of Fermi resonance between aldehydic carbonyl stretching at 1696 cm(-1) and a combination mode of ring stretch near 1059 cm(-1) and deformation vibration, 625 cm(-1). A strong Raman aldehydic torsional mode at 62 cm(-1) is interpreted to correspond to the dominant ON-trans over cis rotamers population. Copyright © 2011 Elsevier B.V. All rights reserved.

  12. Vibrational relaxation pathways of AI and AII modes in N-methylacetamide clusters.

    Science.gov (United States)

    Piatkowski, L; Bakker, H J

    2010-11-04

    We studied the pathways of vibrational energy relaxation of the amide I (~1660 cm⁻¹) and amide II (~1560 cm⁻¹) vibrational modes of N-methylacetamide (NMA) in CCl₄ solution using two-color femtosecond vibrational spectroscopy. We measured the transient spectral dynamics upon excitation of each of these amide modes. The results show that there is no energy transfer between the amide I (AI) and amide II (AII) modes. Instead we find that the vibrational energy is transferred on a picosecond time scale to a common combination tone of lower-frequency modes. By use of polarization-resolved femtosecond pump-probe measurements we also study the reorientation dynamics of the NMA molecules and the relative angle between the transition dipole moments of the AI and AII vibrations. The spectral dynamics at later times after the excitation (>40 ps) reveal the presence of a dissociation process of the NMA aggregates, trimers, and higher order structures into dimers and monomers. By measuring the dissociation kinetics at different temperatures, we determined the activation energy of this dissociation E(a) = 35 ± 3 kJ mol⁻¹.

  13. Damping heat coefficient - Theoretical and experimental research on a vibrating beam

    Science.gov (United States)

    Mihalec, Marko; Javh, Jaka; Cianetti, Filippo; Moretti, Michele; Rossi, Gianluca; Slavič, Janko; Boltežar, Miha

    2017-07-01

    Vibrating systems dissipate their vibrational energy through different mechanisms, commonly referred to as damping. Damping converts the vibrational energy into other forms, such as heat and sound radiation. Heating of the material is often assumed to be one of the biggest drains of energy; however, the measurable temperature increase is at the level of milli Kelvin and hard to measure. This research introduces a damping heat coefficient, the coefficient of total dissipated energy that is converted into heat. Using this coefficient, the expected temperature change of a beam is theoretically related to its damping ratio. In addition, the damping heat coefficient is determined experimentally by measuring the temperature increase of a vibrating beam. Based on modal damping, it is shown that different amounts of energy are dissipated at different parts of the structure. The numerical heat model was experimentally confirmed.

  14. Simulation of Heat Generating In a Vibrating Structure Using COMSOL Multiphysics

    Directory of Open Access Journals (Sweden)

    Ali Kamil Jebur

    2016-03-01

    Full Text Available This paper dealt with heat generating in a beam structure model subjected to small vibrations to know the viscos elastic behavior under heat and vibration. The model first computed coupled thermal – structural interaction. The results obtained from this analysis of the model treated by the finite element method to calculate amount of heat generation in the material. A transient heat transfer analysis then simulated the slow rising temperature in the beam using these heat source terms. The model has been constructed from two blocks, the first block from Aluminum while the second block made from β –Titanium. The model was constrained from one side, while the other side free, so vibrations that occur along the model. These vibrations led to heat generating, so yields that residual stresses through the model. The result obtained represented in curves which give good agreement with international published researches

  15. Non-linear vibrational modes in biomolecules: A periodic orbits description

    Energy Technology Data Exchange (ETDEWEB)

    Kampanarakis, Alexandros [Department of Chemistry, University of Crete, and Institute of Electronic Structure and Laser, Foundation for Research and Technology-Hellas (FORTH), Vasilika Vouton, Heraklion 71110, Crete (Greece); Farantos, Stavros C., E-mail: farantos@iesl.forth.gr [Department of Chemistry, University of Crete, and Institute of Electronic Structure and Laser, Foundation for Research and Technology-Hellas (FORTH), Vasilika Vouton, Heraklion 71110, Crete (Greece); Daskalakis, Vangelis; Varotsis, Constantinos [Department of Environmental Science and Technology, Cyprus University of Technology, 31 Archbishop Kyprianos St., P.O. Box 50329, 3603 Lemesos (Cyprus)

    2012-05-03

    Graphical abstract: Vibrational frequency shifts in Fe{sup IV} = O species of the active site of cytochrome c oxidase are attributed to changes in the surrounding Coulomb field. Periodic orbits analysis assists to find the most anharmonic modes in model biomolecules. Highlights: Black-Right-Pointing-Pointer Periodic orbits are extended to multidimensional potentials of biomolecules. Black-Right-Pointing-Pointer Highly anharmonic vibrational modes and center-saddle bifurcations are detected. Black-Right-Pointing-Pointer Vibrational frequencies shifts in Oxoferryl species of CcO are observed. - Abstract: The vibrational harmonic normal modes of a molecule, which are valid at energies close to an equilibrium point (a minimum, maximum or saddle of the potential energy surface), are extended by periodic orbits to high energies where anharmonicity and coupling of the degrees of freedom are significant. In this way the assignment of the spectra, and thus the extraction of dynamics in highly excited molecules, can be obtained. New vibrational modes emanating from bifurcations of periodic orbits and long living localized trajectories signal the birth and localization of new quantum states. In this article we review and further study non-linear vibrational modes for model biomolecules such as alanine dipeptide and the active site in the oxoferryl oxidation state of the enzyme cytochrome c oxidase. We locate periodic orbits which exhibit high anhamonicity and lead to center-saddle bifurcations. These modes are associated to an isomerization process in alanine dipeptide and to frequency shifts in the oxoferryl observed by modifying the Coulomb field around the Imidazole-Fe{sup IV} = O species.

  16. Mode shape combination in a two-dimensional vibration energy harvester through mass loading structural modification

    Energy Technology Data Exchange (ETDEWEB)

    Sharpes, Nathan; Kumar, Prashant [Center for Energy Harvesting Materials and Systems (CEHMS), Virginia Tech, Blacksburg, Virginia 24061 (United States); Abdelkefi, Abdessattar; Abdelmoula, Hichem [Department of Mechanical and Aerospace Engineering, New Mexico State University, Las Cruces, New Mexico 88003 (United States); Adler, Jan [Center for Energy Harvesting Materials and Systems (CEHMS), Virginia Tech, Blacksburg, Virginia 24061 (United States); Institute of Dynamics and Vibration Research (IDS), Leibniz Universität, Hannover 30167 (Germany); Priya, Shashank [Center for Energy Harvesting Materials and Systems (CEHMS), Virginia Tech, Blacksburg, Virginia 24061 (United States); Bio-Inspired Materials and Devices Laboratory (BMDL), Virginia Tech, Blacksburg, Virginia 24061 (United States)

    2016-07-18

    Mode shapes in the design of mechanical energy harvesters, as a means of performance increase, have been largely overlooked. Currently, the vast majority of energy harvester designs employ some variation of a single-degree-of-freedom cantilever, and the mode shapes of such beams are well known. This is especially true for the first bending mode, which is almost exclusively the chosen vibration mode for energy harvesting. Two-dimensional beam shapes (those which curve, meander, spiral, etc., in a plane) have recently gained research interest, as they offer freedom to modify the vibration characteristics of the harvester beam for achieving higher power density. In this study, the second bending mode shape of the “Elephant” two-dimensional beam shape is examined, and its interaction with the first bending mode is evaluated. A combinatory mode shape created by using mass loading structural modification to lower the second bending modal frequency was found to interact with the first bending mode. This is possible since the first two bending modes do not share common areas of displacement. The combined mode shape is shown to produce the most power of any of the considered mode shapes.

  17. Study of surface modes on a vibrating electrowetting liquid lens

    Science.gov (United States)

    Strauch, Matthias; Shao, Yifeng; Bociort, Florian; Urbach, H. Paul

    2017-10-01

    The increased usage of liquid lenses motivates us to investigate surface waves on the liquid's surface. During fast focal switching, the surface waves decrease the imaging quality. We propose a model that describes the surface modes appearing on a liquid lens and predicts the resonance frequencies. The effects of those surface modes on a laser beam are simulated using Fresnel propagation, and the model is verified experimentally.

  18. Experimental simulation of nanosatellites heat modes

    Directory of Open Access Journals (Sweden)

    Zavadskaja E. S.

    2013-06-01

    Full Text Available The technology of thermal modes modelling for nanosatellite (NS PolyITAN-1 has been developed and thermal vacuum tests have been carried out. The results have shown that the simulation of the NS orbit and space factors is correct and confirmed that NS nodes and elements are operable under the specified conditions.

  19. Synthesis of stiffness and mass matrices from experimental vibration modes.

    Science.gov (United States)

    Ross, R. G., Jr.

    1971-01-01

    With highly complex structures, it is sometimes desirable to derive a dynamic model of the system from experimental vibration data. This paper presents algorithms for synthesizing the mass and stiffness matrices from experimentally derived modal data in a way which preserves the physical significance of the individual mass and stiffness elements. The synthesizing procedures allow for the incorporation of other mass and stiffness data, whether empirical or based on the analyst's insight. The mass and stiffness matrices are derived for a cantilever beam example and are compared with those obtained using earlier techniques.

  20. An Electromagnetic MEMS Energy Harvester Array with Multiple Vibration Modes

    Directory of Open Access Journals (Sweden)

    Huicong Liu

    2015-07-01

    Full Text Available This paper reports the design, micromachining and characterization of an array of electromagnetic energy harvesters (EHs with multiple frequency peaks. The authors present the combination of three multi-modal spring-mass structures so as to realize at least nine resonant peaks within a single microelectromechanical systems (MEMS chip. It is assembled with permanent magnet to show an electromagnetic-based energy harvesting capability. This is the first demonstration of multi-frequency MEMS EH existing with more than three resonant peaks within a limited frequency range of 189 to 662 Hz. It provides a more effective approach to harvest energy from the vibration sources of multiple frequency peaks.

  1. Computation of expectation values from vibrational coupled-cluster at the two-mode coupling level

    DEFF Research Database (Denmark)

    Zoccante, Alberto; Seidler, Peter; Christiansen, Ove

    2011-01-01

    In this work we show how the vibrational coupled-cluster method at the two-mode coupling level can be used to calculate zero-point vibrational averages of properties. A technique is presented, where any expectation value can be calculated using a single set of Lagrangian multipliers computed...... solving iteratively a single linear set of equations. Sample calculations are presented which show that the resulting algorithm scales only with the third power of the number of modes, therefore making large systems accessible. Moreover, we present applications to water, pyrrole, and para-nitroaniline....

  2. A study of the eigenvectors of the vibrational modes in crystalline cytidine via high-pressure Raman spectroscopy.

    Science.gov (United States)

    Lee, Scott A; Pinnick, David A; Anderson, A

    2015-01-01

    Raman spectroscopy has been used to study the eigenvectors and eigenvalues of the vibrational modes of crystalline cytidine at 295 K and high pressures by evaluating the logarithmic derivative of the vibrational frequency ω with respect to pressure P: [Formula: see text]. Crystalline samples of molecular materials have strong intramolecular bonds and weak intermolecular bonds. This hierarchy of bonding strengths causes the vibrational optical modes localized within a molecular unit ("internal" modes) to be relatively high in frequency while the modes in which the molecular units vibrate against each other ("external" modes) have relatively low frequencies. The value of the logarithmic derivative is a useful diagnostic probe of the nature of the eigenvector of the vibrational modes because stretching modes (which are predominantly internal to the molecule) have low logarithmic derivatives while external modes have higher logarithmic derivatives. In crystalline cytidine, the modes at 85.8, 101.4, and 110.6 cm(-1) are external in which the molecules of the unit cell vibrate against each other in either translational or librational motions (or some linear combination thereof). All of the modes above 320 cm(-1) are predominantly internal stretching modes. The remaining modes below 320 cm(-1) include external modes and internal modes, mostly involving either torsional or bending motions of groups of atoms within a molecule.

  3. Collisional relaxation of the three vibrationally excited difluorobenzene isomers by collisions with CO2: effect of donor vibrational mode.

    Science.gov (United States)

    Mitchell, Deborah G; Johnson, Alan M; Johnson, Jeremy A; Judd, Kortney A; Kim, Kilyoung; Mayhew, Maurine; Powell, Amber L; Sevy, Eric T

    2008-02-14

    Relaxation of highly vibrationally excited 1,2-, 1,3-, and 1,4-difluorobenzne (DFB) by collisions with carbon dioxide has been investigated using diode laser transient absorption spectroscopy. Vibrationally hot DFB (E' approximately 41,000 cm(-1)) was prepared by 248 nm excimer laser excitation followed by rapid radiationless relaxation to the ground electronic state. Collisions between hot DFB isomers and CO2 result in large amounts of rotational and translational energy transfer from the hot donors to the bath. The CO2 nascent rotational population distribution of the high-J (J = 58-80) tail of the 00(0)0 state was probed at short times following the excimer laser pulse to measure rate constants and probabilities for collisions populating these states. The amount of translational energy gained by CO2 during collisions was determined using Doppler spectroscopy to measure the width of the absorption line for each transition. The energy transfer probability distribution function, P(E,E'), for the large DeltaE tail was obtained by resorting the state-indexed energy transfer probabilities as a function of DeltaE. P(E,E') was fit to a biexponential function to determine the average energy transferred in a single DFB/CO2 collision and fit parameters describing the shape of P(E,E'). P(E,E') fit parameters for DFB/CO2 and the previously studied C6F6/CO2 system are compared to various donor molecular properties. A model based on Fermi's Golden Rule indicates that the shape of P(E,E') is primarily determined by the low-frequency out-of-plane donor vibrational modes. A fractional mode population analysis is performed, which suggests that for energy transfer from DFB and C6F6 to CO2 the two key donor vibrational modes from which energy leaks out of the donor into the bath are nu11 and nu16. These "gateway" modes are some of the same modes determined to be the most efficient energy transfer modes by quantum scattering studies of benzene/He collisions.

  4. HEAT AND AIR MODES OF AGRICULTURAL STRUCTURES

    OpenAIRE

    Kharchenko P. M.; Timofeev V. P.

    2016-01-01

    In this article, there are descriptions of ventilation systems of municipal and industrial buildings. We consider the scheme of natural ventilation and ventilation with mechanical drive. In agriculture production, processes accompanied by the releasing into the air of premises various harmful substances: gases and vapors, excess of heat and moisture. The source of the fumes and gases are various technological processes. People, animals and birds in the premises, release carbon dioxide and oth...

  5. Mode-selective vibrational modulation of charge transport in organic electronic devices

    KAUST Repository

    Bakulin, Artem A.

    2015-08-06

    The soft character of organic materials leads to strong coupling between molecular, nuclear and electronic dynamics. This coupling opens the way to influence charge transport in organic electronic devices by exciting molecular vibrational motions. However, despite encouraging theoretical predictions, experimental realization of such approach has remained elusive. Here we demonstrate experimentally that photoconductivity in a model organic optoelectronic device can be modulated by the selective excitation of molecular vibrations. Using an ultrafast infrared laser source to create a coherent superposition of vibrational motions in a pentacene/C60 photoresistor, we observe that excitation of certain modes in the 1,500–1,700 cm−1 region leads to photocurrent enhancement. Excited vibrations affect predominantly trapped carriers. The effect depends on the nature of the vibration and its mode-specific character can be well described by the vibrational modulation of intermolecular electronic couplings. This presents a new tool for studying electron–phonon coupling and charge dynamics in (bio)molecular materials.

  6. Study of surface modes on a vibrating electrowetting liquid lens

    NARCIS (Netherlands)

    Strauch, M.; Shao, Y.; Bociort, F.; Urbach, Paul

    2017-01-01

    The increased usage of liquid lenses motivates us to investigate surface waves on the liquid's surface. During fast focal switching, the surface waves decrease the imaging quality. We propose a model that describes the surface modes appearing on a liquid lens and predicts the resonance

  7. Improved orthogonality check for measured modes. [from ground vibration testing of structures

    Science.gov (United States)

    Berman, A.

    1980-01-01

    A method is proposed for performing an orthogonality check for normal modes derived from ground vibration testing. The method utilizes partitioned mass and stiffness matrices for a linear undamped representation of a structure. The normalization of the modes by the proposed method inherently includes the effects of significant displacements which were not measured; and the method may allow the use of fewer measurement points than would be necessary with the conventional method.

  8. Vibrational relaxation of the bending mode of HDO in liquid D2O.

    Science.gov (United States)

    Bodis, Pavol; Larsen, Olaf F A; Woutersen, Sander

    2005-06-23

    The vibrational relaxation of the bending mode of HDO in liquid D2O has been studied using time-resolved mid-infrared pump-probe spectroscopy. At short delays, the transient spectrum clearly shows the v = 1 --> 2 induced absorption and v = 1 --> 0 bleaching and stimulated emission, whereas at long delays, the transient spectrum is dominated by the spectral changes caused by the temperature increase in the sample after vibrational relaxation. From the decay of the v = 1 --> 2 induced absorption, we obtain an estimate of 390 +/- 50 fs for the vibrational lifetime, in surprisingly good agreement with recent theoretical predictions. In the v = 0 --> 1 frequency region, the decay of the absorption change involves a second, slower component, which suggests that after vibrational relaxation the system is not yet in thermal equilibrium.

  9. Vibrational resonance induced by transition of phase-locking modes in excitable systems.

    Science.gov (United States)

    Yang, Lijian; Liu, Wangheng; Yi, Ming; Wang, Canjun; Zhu, Qiaomu; Zhan, Xuan; Jia, Ya

    2012-07-01

    We study the occurrence of vibrational resonance as well as the underlying mechanism in excitable systems. The single vibration resonance and vibration bi-resonance are observed when tuning the amplitude and frequency of high-frequency force simultaneously. Furthermore, by virtue of the phase diagram of low-frequency-signal-free FitzHugh-Nagumo model, it is found that each maxima of response measure is located exactly at the transition boundary of phase patterns. Therefore, it is the transition between different phase-locking modes that induces vibrational resonance in the excitable systems. Finally, this mechanism is verified in the Hodgkin-Huxley neural model. Our results provide insights into the transmission of weak signals in nonlinear systems, which are valuable in engineering for potential applications.

  10. Casing Vibration Fault Diagnosis Based on Variational Mode Decomposition, Local Linear Embedding, and Support Vector Machine

    Directory of Open Access Journals (Sweden)

    Yizhou Yang

    2017-01-01

    Full Text Available To diagnose mechanical faults of rotor-bearing-casing system by analyzing its casing vibration signal, this paper proposes a training procedure of a fault classifier based on variational mode decomposition (VMD, local linear embedding (LLE, and support vector machine (SVM. VMD is used first to decompose the casing signal into several modes, which are subsignals usually modulated by fault frequencies. Vibrational features are extracted from both VMD subsignals and the original one. LLE is employed here to reduce the dimensionality of these extracted features and make the samples more separable. Then low-dimensional data sets are used to train the multiclass SVM whose accuracy is tested by classifying the test samples. When the parameters of LLE and SVM are well optimized, this proposed method performs well on experimental data, showing its capacity of diagnosing casing vibration faults.

  11. Effective representation of amide III, II, I, and A modes on local vibrational modes: Analysis of ab initio quantum calculation results.

    Science.gov (United States)

    Hahn, Seungsoo

    2016-10-28

    The Hamiltonian matrix for the first excited vibrational states of a protein can be effectively represented by local vibrational modes constituting amide III, II, I, and A modes to simulate various vibrational spectra. Methods for obtaining the Hamiltonian matrix from ab initio quantum calculation results are discussed, where the methods consist of three steps: selection of local vibrational mode coordinates, calculation of a reduced Hessian matrix, and extraction of the Hamiltonian matrix from the Hessian matrix. We introduce several methods for each step. The methods were assessed based on the density functional theory calculation results of 24 oligopeptides with four different peptide lengths and six different secondary structures. The completeness of a Hamiltonian matrix represented in the reduced local mode space is improved by adopting a specific atom group for each amide mode and reducing the effect of ignored local modes. The calculation results are also compared to previous models using C=O stretching vibration and transition dipole couplings. We found that local electric transition dipole moments of the amide modes are mainly bound on the local peptide planes. Their direction and magnitude are well conserved except amide A modes, which show large variation. Contrary to amide I modes, the vibrational coupling constants of amide III, II, and A modes obtained by analysis of a dipeptide are not transferable to oligopeptides with the same secondary conformation because coupling constants are affected by the surrounding atomic environment.

  12. District Heating Mode Analysis Based on an Air-cooled Combined Heat and Power Station

    Directory of Open Access Journals (Sweden)

    Pei Feng Li

    2014-03-01

    Full Text Available As an important research subject, district heating with combined heat and power (CHP has significant potential for energy conservation. This paper utilised a 200 MW air-cooled unit as an actual case and presented a design scheme and energy consumption analysis of three typical CHP modes, including the low vacuum mode (LVM, the extraction condensing mode (ECM, and the absorbing heat pump mode (AHPM. The advantages and disadvantages of each mode (including their practical problems were analysed, and suggestions for the best mode were proposed. The energy consumption of the three heating modes changed with the heating load. When the heating load was increased, the net power of the entire system decreased to different degrees. In this paper, the energy conservation effect of the LVM was the most ideal, followed by the ECM and the AHPM. Besides, the LVM and AHPM were able to supply larger heat loads than the ECM, which was limited by the minimum cooling flow of the low pressure cylinder. Furthermore, in order to get a more general conclusion, a similar case with an air-cooled 300 MW unit is studied, showing that the fuel consumption levels of ECM and AHPM have changed.

  13. Mode pattern of internal flow in a water droplet on a vibrating hydrophobic surface.

    Science.gov (United States)

    Kim, Hun; Lim, Hee-Chang

    2015-06-04

    The objective of this study is to understand the mode pattern of the internal flow in a water droplet placed on a hydrophobic surface that periodically and vertically vibrates. As a result, a water droplet on a vibrating hydrophobic surface has a typical shape that depends on each resonance mode, and, additionally, we observed a diversified lobe size and internal flows in the water droplet. The size of each lobe at the resonance frequency was relatively greater than that at the neighboring frequencies, and the internal flow of the nth order mode was also observed in the flow visualization. In general, large symmetrical flow streams were generated along the vertical axis in each mode, with a large circulating movement from the bottom to the top, and then to the triple contact line along the droplet surface. In contrast, modes 2 and 4 generated a Y-shaped flow pattern, in which the flow moved to the node point in the lower part of the droplet, but modes 6 and 8 had similar patterns, with only a little difference. In addition, as a result of the PIV measurement, while the flow velocity of mode 4 was faster than that of model 2, those of modes 6 and 8 were almost similar.

  14. Modes of vibration in a circular plate with three simple support points.

    Science.gov (United States)

    Chi, C.

    1972-01-01

    The analytical solutions for the vibrational modes of a thin circular flat plate that is simply supported at three points on the circumference are presented. The mode shapes and corresponding eigenvalues are obtained. Results show that the modes can be grouped into four different types depending on the manner by which they receive the pressure at the supported points. The problem is of the mixed boundary value type in that some portion of the boundary is free while the other portion is simply supported.

  15. Observation of sound-induced corneal vibrational modes by optical coherence tomography

    OpenAIRE

    Akca, B. Imran; Chang, Ernest W.; Kling, Sabine; Ramier, Antoine; Scarcelli, Giuliano; Marcos, Susana; Yun, Seok H.

    2015-01-01

    The mechanical stability of the cornea is critical for maintaining its normal shape and refractive function. Here, we report an observation of the mechanical resonance modes of the cornea excited by sound waves and detected by using phase-sensitive optical coherence tomography. The cornea in bovine eye globes exhibited three resonance modes in a frequency range of 50-400 Hz. The vibration amplitude of the fundamental mode at 80-120 Hz was ~8 µm at a sound pressure level of 100 dB (2 Pa). Vibr...

  16. Energy trapping of thickness-shear vibration modes of elastic plates with functionally graded materials.

    Science.gov (United States)

    Wang, Ji; Yang, Jiashi; Li, Jiangyu

    2007-03-01

    Energy trapping has important applications in the design of thickness-shear resonators. Considerable efforts have been made for the effective utilization and improvement of energy trapping with variations of plate configurations, such as adding electrodes and contouring. As a new approach in seeking improved energy trapping feature, we analyze thickness-shear vibrations in an elastic plate with functionally graded material (FGM) of in-plane variation of mechanical properties, such as elastic constants and density. A simple and general equation governing the thickness-shear modes is derived from a variational analysis. A plate with piecewise constant material properties is analyzed as an example. It is shown that such a plate can support thickness-shear vibration modes with obvious energy trapping. Bechmann's number for the existence of only one trapped mode also can be determined accordingly.

  17. Imaging the surface stress and vibration modes of a microcantilever by laser beam deflection microscopy.

    Science.gov (United States)

    Tamayo, Javier; Pini, Valerio; Kosaka, Prisicila; Martinez, Nicolas F; Ahumada, Oscar; Calleja, Montserrat

    2012-08-10

    There is a need for noninvasive techniques for simultaneous imaging of the stress and vibration mode shapes of nanomechanical systems in the fields of scanning probe microscopy, nanomechanical biological and chemical sensors and the semiconductor industry. Here we show a novel technique that combines a scanning laser, the beam deflection method and digital multifrequency excitation and analysis for simultaneous imaging of the static out-of-plane displacement and the shape of five vibration modes of nanomechanical systems. The out-of-plane resolution is at least 100 pm Hz⁻¹/² and the lateral resolution, which is determined by the laser spot size, is 1-1.5 μm. The capability of the technique is demonstrated by imaging the residual surface stress of a microcantilever together with the shape of the first 22 vibration modes. The vibration behavior is compared with rigorous finite element simulations. The technique is suitable for major improvements in the imaging of liquids, such as higher bandwidth and enhanced spatial resolution.

  18. Effect of instantaneous and continuous quenches on the density of vibrational modes in model glasses

    Science.gov (United States)

    Lerner, Edan; Bouchbinder, Eran

    2017-08-01

    Computational studies of supercooled liquids often focus on various analyses of their "underlying inherent states"—the glassy configurations at zero temperature obtained by an infinitely fast (instantaneous) quench from equilibrium supercooled states. Similar protocols are also regularly employed in investigations of the unjamming transition at which the rigidity of decompressed soft-sphere packings is lost. Here we investigate the statistics and localization properties of low-frequency vibrational modes of glassy configurations obtained by such instantaneous quenches. We show that the density of vibrational modes grows as ωβ with β depending on the parent temperature T0 from which the glassy configurations were instantaneously quenched. For quenches from high temperature liquid states we find β ≈3 , whereas β appears to approach the previously observed value β =4 as T0 approaches the glass transition temperature. We discuss the consistency of our findings with the theoretical framework of the soft potential model, and contrast them with similar measurements performed on configurations obtained by continuous quenches at finite cooling rates. Our results suggest that any physical quench at rates sufficiently slower than the inverse vibrational time scale—including all physically realistic quenching rates of molecular or atomistic glasses—would result in a glass whose density of vibrational modes is universally characterized by β =4 .

  19. Based On Intrinsic Mode Function Energy Tracking Method of Circuit Breaker Vibration Signal Feature Extraction Studies

    Directory of Open Access Journals (Sweden)

    Sun Yi-Hang

    2017-01-01

    Full Text Available In order to detect a mechanical type of structural failure of the circuit breaker, the characteristics of the circuit breaker mechanical vibration signal is analyzed in this paper. A combination of medium voltage circuit breaker based on empirical mode decomposition (EMD amount of energy and support vector machine (SVM theory vibration signal feature vector extraction and analysis of fault classification method is proposed. First, the vibration signal of the circuit breaker is decomposed by EMD, then intrinsic mode function (IMF is obtain. The major fault feature information intrinsic mode functions the amount of energy of the component is obtained by discrete sampling points and the amount of energy. Using the amount of energy of IMF component as a feature vector, the failure of the test sample signal as input feature vector into trained “BT-SVM” support vector machine classification mechanism for fault classification. The differences and fault type of vibration signals can be identified by this method through the experimental analysis.

  20. Component mode synthesis and large deflection vibrations of complex structures. [beams and trusses

    Science.gov (United States)

    Mei, C.

    1984-01-01

    The accuracy of the NASTRAN modal synthesis analysis was assessed by comparing it with full structure NASTRAN and nine other modal synthesis results using a nine-bay truss. A NASTRAN component mode transient response analysis was also performed on the free-free truss structure. A finite element method was developed for nonlinear vibration of beam structures subjected to harmonic excitation. Longitudinal deformation and inertia are both included in the formula. Tables show the finite element free vibration results with and without considering the effects of longitudinal deformation and inertia as well as the frequency ratios for a simply supported and a clamped beam subjected to a uniform harmonic force.

  1. Orientations of nonlocal vibrational modes from combined experimental and theoretical sum frequency spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Chase, Hilary M.; Chen, Shunli; Fu, Li; Upshur, Mary Alice; Rudshteyn, Benjamin; Thomson, Regan J.; Wang, Hong-Fei; Batista, Victor S.; Geiger, Franz M.

    2017-09-01

    Inferring molecular orientations from vibrational sum frequency generation (SFG) spectra is challenging in polarization combinations that result in low signal intensities, or when the local point group symmetry approximation fails. While combining experiments with density functional theory (DFT) could overcome this problem, the scope of the combined method has yet to be established. Here, we assess its feasibility of determining the distributions of molecular orientations for one monobasic ester, two epoxides and three alcohols at the vapor/fused silica interface. We find that molecular orientations of nonlocal vibrational modes cannot be determined using polarization-resolved SFG measurements alone.

  2. Estimation of the mechanical properties of the eye through the study of its vibrational modes.

    Science.gov (United States)

    Aloy, M Á; Adsuara, J E; Cerdá-Durán, P; Obergaulinger, M; Esteve-Taboada, J J; Ferrer-Blasco, T; Montés-Micó, R

    2017-01-01

    Measuring the eye's mechanical properties in vivo and with minimally invasive techniques can be the key for individualized solutions to a number of eye pathologies. The development of such techniques largely relies on a computational modelling of the eyeball and, it optimally requires the synergic interplay between experimentation and numerical simulation. In Astrophysics and Geophysics the remote measurement of structural properties of the systems of their realm is performed on the basis of (helio-)seismic techniques. As a biomechanical system, the eyeball possesses normal vibrational modes encompassing rich information about its structure and mechanical properties. However, the integral analysis of the eyeball vibrational modes has not been performed yet. Here we develop a new finite difference method to compute both the spheroidal and, specially, the toroidal eigenfrequencies of the human eye. Using this numerical model, we show that the vibrational eigenfrequencies of the human eye fall in the interval 100 Hz-10 MHz. We find that compressible vibrational modes may release a trace on high frequency changes of the intraocular pressure, while incompressible normal modes could be registered analyzing the scattering pattern that the motions of the vitreous humour leave on the retina. Existing contact lenses with embebed devices operating at high sampling frequency could be used to register the microfluctuations of the eyeball shape we obtain. We advance that an inverse problem to obtain the mechanical properties of a given eye (e.g., Young's modulus, Poisson ratio) measuring its normal frequencies is doable. These measurements can be done using non-invasive techniques, opening very interesting perspectives to estimate the mechanical properties of eyes in vivo. Future research might relate various ocular pathologies with anomalies in measured vibrational frequencies of the eye.

  3. "Good Vibrations": A workshop on oscillations and normal modes

    Science.gov (United States)

    Barbieri, Sara; Carpineti, Marina; Giliberti, Marco; Rigon, Enrico; Stellato, Marco; Tamborini, Marina

    2016-05-01

    We describe some theatrical strategies adopted in a two hour workshop in order to show some meaningful experiments and the underlying useful ideas to describe a secondary school path on oscillations, that develops from harmonic motion to normal modes of oscillations, and makes extensive use of video analysis, data logging, slow motions and applet simulations. Theatre is an extremely useful tool to stimulate motivation starting from positive emotions. That is the reason why the theatrical approach to the presentation of physical themes has been explored by the group "Lo spettacolo della Fisica" (http://spettacolo.fisica.unimi.it) of the Physics Department of University of Milano for the last ten years (Carpineti et al., JCOM, 10 (2011) 1; Nuovo Cimento B, 121 (2006) 901) and has been inserted also in the European FP7 Project TEMI (Teaching Enquiry with Mysteries Incorporated, see http://teachingmysteries.eu/en) which involves 13 different partners coming from 11 European countries, among which the Italian (Milan) group. According to the TEMI guidelines, this workshop has a written script based on emotionally engaging activities of presenting mysteries to be solved while participants have been involved in nice experiments following the developed path.

  4. Space structure vibration modes: How many exist? Which ones are important?

    Science.gov (United States)

    Hughes, P. C.

    1984-01-01

    This report attempts to shed some light on the two issues raised in the title, namely, how many vibration modes does a real structure have, and which of these modes are important? The surprise-free answers to these two questions are, respectively, an infinite number and the first several modes. The author argues that the absurd subspace (all but the first billion modes) is not a strength of continuum modeling, but, in fact, a weakness. Partial differential equations are not real structures, only mathematical models. This note also explains (1) that the PDE model and the finite element model are, in fact, the same model, the latter being a numerical method for dealing with the former, (2) that modes may be selected on dynamical grounds other than frequency alone, and (3) that long slender rods are useful as primitive cases but dangerous to extrapolate from.

  5. Using input command pre-shaping to suppress multiple mode vibration

    Science.gov (United States)

    Hyde, James M.; Seering, Warren P.

    1990-01-01

    Spacecraft, space-borne robotic systems, and manufacturing equipment often utilize lightweight materials and configurations that give rise to vibration problems. Prior research has led to the development of input command pre-shapers that can significantly reduce residual vibration. These shapers exhibit marked insensitivity to errors in natural frequency estimates and can be combined to minimize vibration at more than one frequency. This paper presents a method for the development of multiple mode input shapers which are simpler to implement than previous designs and produce smaller system response delays. The new technique involves the solution of a group of simultaneous non-linear impulse constraint equations. The resulting shapers were tested on a model of MACE, an MIT/NASA experimental flexible structure.

  6. Unified gas-kinetic scheme for diatomic molecular flow with translational, rotational, and vibrational modes

    Science.gov (United States)

    Wang, Zhao; Yan, Hong; Li, Qibing; Xu, Kun

    2017-12-01

    The unified gas-kinetic scheme (UGKS) is a direct modeling method for both continuum and rarefied flow computations. In the previous study, the UGKS was developed for diatomic molecular simulations with translation and rotational motions. In this paper, a UGKS with non-equilibrium translational, rotational, and vibrational degrees of freedom, will be developed. The new scheme is based on the phenomenological gas dynamics model, where the translational, rotational, and vibrational modes get to the equilibrium with different time scales with the introduction of rotational and vibrational collision numbers. This new scheme is tested in a few cases, such as the homogeneous flow relaxation, shock structure, shock tube problem, and flow passing through a circular and semi-circular cylinders. The analytical and DSMC solutions are used for the validation of the UGKS, and reasonable agreements have been achieved.

  7. Design for coupled-mode flutter and non-synchronous vibration in turbomachinery

    Science.gov (United States)

    Clark, Stephen Thomas

    This research presents the detailed investigation of coupled-mode flutter and non-synchronous vibration in turbomachinery. Coupled-mode flutter and non-synchronous vibration are two aeromechanical challenges in designing turbomachinery that, when present, can cause engine blade failure. Regarding flutter, current industry design practices calculate the aerodynamic loads on a blade due to a single mode. In response to these design standards, a quasi three-dimensional, reduced-order modeling tool was developed for identifying the aeroelastic conditions that cause multi-mode flutter. This tool predicts the onset of coupled-mode flutter reasonable well for four different configurations, though certain parameters were tuned to agree with experimentation. Additionally, the results of this research indicate that mass ratio, frequency separation, and solidity have an effect on critical rotor speed for flutter. Higher mass-ratio blades require larger rotational velocities before they experience coupled-mode flutter. Similarly, increasing the frequency separation between modes and raising the solidity increases the critical rotor speed. Finally, and most importantly, design guidelines were generated for defining when a multi-mode flutter analysis is required in practical turbomachinery design. Previous work has shown that industry computational fluid dynamics can approximately predict non-synchronous vibration (NSV), but no real understanding of frequency lock-in and blade limit-cycle amplitude exists. Therefore, to understand the causes of NSV, two different reduced-order modeling approaches were used. The first approach uses a van der Pol oscillator to model a non-linear fluid instability. The van der Pol model is then coupled to a structural degree of freedom. This coupled system exhibits the two chief properties seen in experimental and computational non-synchronous vibration. Under various conditions, the fluid instability and the natural structural frequency will lock

  8. Shear-horizontal vibration modes of an oblate elliptical cylinder and energy trapping in contoured acoustic wave resonators.

    Science.gov (United States)

    He, Huijing; Yang, Jiashi; Kosinski, John A

    2012-08-01

    We study shear-horizontal free vibrations of an elastic cylinder with an oblate elliptical cross section and a traction-free surface. Exact vibration modes and frequencies are obtained. The results show the existence of thickness-shear and thickness-twist modes. The energy-trapping behavior of these modes is examined. Trapped modes are found wherein the vibration energy is largely confined to the central portion of the cross section and little vibration energy is found at the edges. It is also shown that face-shear modes are not allowed in such a cylinder. The results are useful for the understanding of the energy trapping phenomenon in contoured acoustic wave resonators.

  9. Vortex-induced vibration of a tension leg platform tendon: multi-mode limit cycle oscillations

    Science.gov (United States)

    Datta, Nabanita

    2017-11-01

    This paper studies the application of mathematical models to analyze the vortex-induced vibrations of the tendons of a given TLP along the Indian coastline, by using an analytical approach, analyzed using MATLAB. The tendon is subjected to a steady current load, which causes vortex-shedding downstream, leading to cross-flow vibrations. The magnitude of the excitation (lift and drag coefficients) depends on the vortex-shedding frequency. The resulting vibration is studied for possible resonant behavior. The excitation force is quantified empirically, the added mass by potential flow hydrodynamics, and the vibration by normal mode summation method. Non-linear viscous damping of the water is considered. The non-linear oscillations are studied by the phase-plane method, investigating the limit-cycle oscillations. The stable/unstable regions of the dynamic behavior are demarcated. The modal contribution to the total deflection is studied to establish the possibility of resonance of one of the wet modes with the vortex-shedding frequency.

  10. Mode coupling and multiquantum vibrational excitations in Feshbach-resonant positron annihilation in molecules

    Science.gov (United States)

    Gribakin, G. F.; Stanton, J. F.; Danielson, J. R.; Natisin, M. R.; Surko, C. M.

    2017-12-01

    The dominant mechanism of low-energy positron annihilation in polyatomic molecules is through positron capture in vibrational Feshbach resonances (VFR). In this paper, we investigate theoretically the effect of anharmonic terms in the vibrational Hamiltonian on positron annihilation rates. Such interactions enable positron capture in VFRs associated with multiquantum vibrational excitations, leading to enhanced annihilation. Mode coupling can also lead to faster depopulation of VFRs, thereby reducing their contribution to the annihilation rates. To analyze this complex picture, we use coupled-cluster methods to calculate the anharmonic vibrational spectra and dipole transition amplitudes for chloroform, chloroform-d1, 1,1-dichloroethylene, and methanol, and use these data to compute positron resonant annihilation rates for these molecules. Theoretical predictions are compared with the annihilation rates measured as a function of incident positron energy. The results demonstrate the importance of mode coupling in both enhancement and suppression of the VFR. There is also experimental evidence for the direct excitation of multimode VFR. Their contribution is analyzed using a statistical approach, with an outlook towards more accurate treatment of this phenomenon.

  11. Vortex-induced vibration of a tension leg platform tendon: Multi-mode limit cycle oscillations

    Science.gov (United States)

    Datta, Nabanita

    2017-12-01

    This paper studies the application of mathematical models to analyze the vortex-induced vibrations of the tendons of a given TLP along the Indian coastline, by using an analytical approach, analyzed using MATLAB. The tendon is subjected to a steady current load, which causes vortex-shedding downstream, leading to cross-flow vibrations. The magnitude of the excitation (lift and drag coefficients) depends on the vortex-shedding frequency. The resulting vibration is studied for possible resonant behavior. The excitation force is quantified empirically, the added mass by potential flow hydrodynamics, and the vibration by normal mode summation method. Non-linear viscous damping of the water is considered. The non-linear oscillations are studied by the phase-plane method, investigating the limit-cycle oscillations. The stable/unstable regions of the dynamic behavior are demarcated. The modal contribution to the total deflection is studied to establish the possibility of resonance of one of the wet modes with the vortex-shedding frequency.

  12. Chemical reactions of water molecules on Ru(0001) induced by selective excitation of vibrational modes

    Energy Technology Data Exchange (ETDEWEB)

    Mugarza, Aitor; Shimizu, Tomoko K.; Ogletree, D. Frank; Salmeron, Miquel

    2009-05-07

    Tunneling electrons in a scanning tunneling microscope were used to excite specific vibrational quantum states of adsorbed water and hydroxyl molecules on a Ru(0 0 0 1) surface. The excited molecules relaxed by transfer of energy to lower energy modes, resulting in diffusion, dissociation, desorption, and surface-tip transfer processes. Diffusion of H{sub 2}O molecules could be induced by excitation of the O-H stretch vibration mode at 445 meV. Isolated molecules required excitation of one single quantum while molecules bonded to a C atom required at least two quanta. Dissociation of single H{sub 2}O molecules into H and OH required electron energies of 1 eV or higher while dissociation of OH required at least 2 eV electrons. In contrast, water molecules forming part of a cluster could be dissociated with electron energies of 0.5 eV.

  13. Site-selective detection of vibrational modes of an iron atom in a trinuclear complex

    Energy Technology Data Exchange (ETDEWEB)

    Faus, Isabelle, E-mail: faus@rhrk.uni-kl.de; Rackwitz, Sergej; Wolny, Juliusz A. [University of Kaiserslautern, Department of Physics (Germany); Banerjee, Atanu; Kelm, Harald; Krüger, Hans-Jörg [University of Kaiserslautern, Department of Chemistry (Germany); Schlage, Kai; Wille, Hans-Christian [DESY, PETRA III, P01 (Germany); Schünemann, Volker [University of Kaiserslautern, Department of Physics (Germany)

    2016-12-15

    Nuclear inelastic scattering (NIS) experiments on the trinuclear complex [{sup 57}Fe{L-N_4(CH_2Fc)_2} (CH{sub 3}CN){sub 2}](ClO{sub 4}){sub 2} have been performed. The octahedral iron ion in the complex was labelled with {sup 57}Fe and thereby exclusively the vibrational modes of this iron ion have been detected with NIS. The analysis of nuclear forward scattering (NFS) data yields a ferrous low-spin state for the {sup 57}Fe labelled iron ion. The simulation of the partial density of states (pDOS) for the octahedral low-spin iron(II) ion of the complex by density functional theory (DFT) calculations is in excellent agreement with the experimental pDOS of the complex determined from the NIS data obtained at 80 K. Thereby it was possible to assign almost each of the experimentally observed NIS bands to the corresponding molecular vibrational modes.

  14. Multiple mode analysis of the self-excited vibrations of rotary drilling systems

    Science.gov (United States)

    Germay, Christophe; Denoël, Vincent; Detournay, Emmanuel

    2009-08-01

    This paper extends the analysis of the self-excitated vibrations of a drilling structure presented in an earlier paper [T. Richard, C. Germay, E. Detournay, A simplified model to explore the root cause of stick-slip vibrations in drilling systems with drag bits, Journal of Sound and Vibration 305 (3) (2007) 432-456] by basing the formulation of the model on a continuum representation of the drillstring rather than on a characterization of the drilling structure by a 2 degree of freedom system. The particular boundary conditions at the bit-rock interface, which according to this model are responsible for the self-excited vibrations, account for both cutting and frictional contact processes. The cutting process combined with the quasi-helical motion of the bit leads to a regenerative effect that introduces a coupling between the axial and torsional modes of vibrations and a state-dependent delay in the governing equations, while the frictional contact process is associated with discontinuities in the boundary conditions when the bit sticks in its axial and angular motion. The dynamic response of the drilling structure is computed using the finite element method. While the general tendencies of the system response predicted by the discrete model are confirmed by this computational model (for example that the occurrence of stick-slip vibrations as well as the risk of bit bouncing are enhanced with an increase of the weight-on-bit or a decrease of the rotational speed), new features in the self-excited response of the drillstring can be detected. In particular, stick-slip vibrations are predicted to occur at natural frequencies of the drillstring different from the fundamental one (as sometimes observed in field operations), depending on the operating parameters.

  15. Optimization procedure to control the coupling of vibration modes in flexible space structures

    Science.gov (United States)

    Walsh, Joanne L.

    1987-01-01

    As spacecraft structural concepts increase in size and flexibility, the vibration frequencies become more closely-spaced. The identification and control of such closely-spaced frequencies present a significant challenge. To validate system identification and control methods prior to actual flight, simpler space structures will be flown. To challenge the above technologies, it will be necessary to design these structures with closely-spaced or coupled vibration modes. Thus, there exists a need to develop a systematic method to design a structure which has closely-spaced vibration frequencies. This paper describes an optimization procedure which is used to design a large flexible structure to have closely-spaced vibration frequencies. The procedure uses a general-purpose finite element analysis program for the vibration and sensitivity analyses and a general-purpose optimization program. Results are presented from two studies. The first study uses a detailed model of a large flexible structure to design a structure with one pair of closely-spaced frequencies. The second study uses a simple equivalent beam model of a large flexible structure to obtain a design with two pairs of closely-spaced frequencies.

  16. Radiation impedance and equivalent circuit for piezoelectric ultrasonic composite transducers of vibrational mode-conversion.

    Science.gov (United States)

    Lin, Shuyu

    2012-01-01

    The piezoelectric ultrasonic composite transducer, which can be used in either gas or liquid media, is studied in this paper. The composite transducer is composed of a longitudinal sandwich piezoelectric transducer, a mechanical transformer, and a metal circular plate in flexural vibration. Acoustic radiation is produced by the flexural circular plate, which is excited by the longitudinal sandwich transducer and transformer. Based on the classic flexural theory of plates, the equivalent lumped parameters for a plate in axially symmetric flexural vibration with free boundary conditions are obtained. The radiation impedance of the plate is derived and the relationship between the radiation impedance and the frequency is analyzed. The equivalent circuits for the plate in flexural vibration and the composite transducer are given. The vibrational modes and the harmonic response of the composite piezoelectric transducer are simulated by the numerical method. Based on the theoretical and numerical analysis, two composite piezoelectric ultrasonic transducers are designed and manufactured, their admittance-frequency curves are measured, and the resonance frequency is obtained. The flexural vibrational displacement distribution of the transducer is measured with a laser scanning vibrometer. It is shown that the theoretical results are in good agreement with the measured resonance frequency and the displacement distribution. © 2012 IEEE

  17. Influence of vibration modes on control system stabilization for space shuttle type vehicles

    Science.gov (United States)

    Greiner, H. G.

    1972-01-01

    An investigation was made to determine the feasibility of using conventional autopilot techniques to stabilize the vibration modes at the liftoff flight condition for two space shuttle configurations. One configuration is called the dual flyback vehicle in which both the orbiter and booster vehicles have wings and complete flyback capability. The other configuration is called the solid motor vehicle win which the orbiter only has flyback. The results of the linear stability analyses for each of the vehicles are summarized.

  18. Electron-Vibration Coupling in Molecular Materials: Assignment of Vibronic Modes from Photoelectron Momentum Mapping.

    Science.gov (United States)

    Graus, M; Grimm, M; Metzger, C; Dauth, M; Tusche, C; Kirschner, J; Kümmel, S; Schöll, A; Reinert, F

    2016-04-08

    Electron-phonon coupling is one of the most fundamental effects in condensed matter physics. We here demonstrate that photoelectron momentum mapping can reveal and visualize the coupling between specific vibrational modes and electronic excitations. When imaging molecular orbitals with high energy resolution, the intensity patterns of photoelectrons of the vibronic sidebands of molecular states show characteristic changes due to the distortion of the molecular frame in the vibronically excited state. By comparison to simulations, an assignment of specific vibronic modes is possible, thus providing unique information on the coupling between electronic and vibronic excitation.

  19. Vibration Control of Flexible Mode for a Beam-Type Substrate Transport Robot

    Directory of Open Access Journals (Sweden)

    Cheol Hoon Park

    2013-07-01

    Full Text Available Beam-type substrate transport robots are widely used to handle substrates, especially in the solar cell manufacturing process. To reduce the takt time and increase productivity, accurate position control becomes increasingly important as the size of the substrate increases. However, the vibration caused by the flexible forks in beam-type robots interferes with accurate positioning, which results in long takt times in the manufacturing process. To minimize the vibration and transport substrates on the fork as fast as possible, the trajectories should be prevented from exciting the flexible modes of the forks. For this purpose, a fifth-order polynomial trajectory generator and input shaping were incorporated into the controller of the beam-type robot in this study. The flexible modes of the forks were identified by measuring the frequency response function (FRF, and the input shaping was designed so as not to excite the flexible modes. The controller was implemented by using MATLAB/xPC Target. In this paper, the design procedure of input shaping and its effectiveness for vibration attenuation in both “no load” and “load” cases is presented.

  20. A MEMS Resonant Sensor to Measure Fluid Density and Viscosity under Flexural and Torsional Vibrating Modes.

    Science.gov (United States)

    Zhao, Libo; Hu, Yingjie; Wang, Tongdong; Ding, Jianjun; Liu, Xixiang; Zhao, Yulong; Jiang, Zhuangde

    2016-06-06

    Methods to calculate fluid density and viscosity using a micro-cantilever and based on the resonance principle were put forward. Their measuring mechanisms were analyzed and the theoretical equations to calculate the density and viscosity were deduced. The fluid-solid coupling simulations were completed for the micro-cantilevers with different shapes. The sensing chips with micro-cantilevers were designed based on the simulation results and fabricated using the micro electromechanical systems (MEMS) technology. Finally, the MEMS resonant sensor was packaged with the sensing chip to measure the densities and viscosities of eight different fluids under the flexural and torsional vibrating modes separately. The relative errors of the measured densities from 600 kg/m³ to 900 kg/m³ and viscosities from 200 μPa·s to 1000 μPa·s were calculated and analyzed with different microcantilevers under various vibrating modes. The experimental results showed that the effects of the shape and vibrating mode of micro-cantilever on the measurement accuracies of fluid density and viscosity were analyzed in detail.

  1. A MEMS Resonant Sensor to Measure Fluid Density and Viscosity under Flexural and Torsional Vibrating Modes

    Directory of Open Access Journals (Sweden)

    Libo Zhao

    2016-06-01

    Full Text Available Methods to calculate fluid density and viscosity using a micro-cantilever and based on the resonance principle were put forward. Their measuring mechanisms were analyzed and the theoretical equations to calculate the density and viscosity were deduced. The fluid-solid coupling simulations were completed for the micro-cantilevers with different shapes. The sensing chips with micro-cantilevers were designed based on the simulation results and fabricated using the micro electromechanical systems (MEMS technology. Finally, the MEMS resonant sensor was packaged with the sensing chip to measure the densities and viscosities of eight different fluids under the flexural and torsional vibrating modes separately. The relative errors of the measured densities from 600 kg/m3 to 900 kg/m3 and viscosities from 200 μPa·s to 1000 μPa·s were calculated and analyzed with different microcantilevers under various vibrating modes. The experimental results showed that the effects of the shape and vibrating mode of micro-cantilever on the measurement accuracies of fluid density and viscosity were analyzed in detail.

  2. Multiple-mode nonlinear free and forced vibrations of beams using finite element method

    Science.gov (United States)

    Mei, Chuh; Decha-Umphai, Kamolphan

    1987-01-01

    Multiple-mode nonlinear free and forced vibration of a beam is analyzed by the finite element method. The geometric nonlinearity is investigated. Inplane displacement and inertia (IDI) are also considered in the formulation. Harmonic force matrix is derived and explained. Nonlinear free vibration can be simply treated as a special case of the general forced vibration by setting the harmonic force matrix equal to zero. The effect of the higher modes is more pronouced for the clamped supported beam than the simply supported one. Beams without IDI yield more effect of the higher modes than the one with IDI. The effects of IDI are to reduce nonlinearity. For beams with end supports restrained from axial movement (immovable cases), only the hardening type nonlinearity is observed. However, beams of small slenderness ratio (L/R = 20) with movable end supports, the softening type nonlinearity is found. The concentrated force case yields a more severe response than the uniformly distributed force case. Finite element results are in good agreement with the solution of simple elliptic response, harmonic balance method, and Runge-Kutte method and experiment.

  3. Modeling of 1-3 piezoelectric composites operating in thickness-stretch vibration mode

    Science.gov (United States)

    Yang, Z.; Wang, H.; Zhao, C.; Zeng, D.

    2015-06-01

    For bulk piezoelectric ceramics plates, the fundamental thickness-stretch (TSt) waves are always coupled to the in-plane extension waves and the symmetric thickness-shear waves. The occurrence of these spurious modes in bulk piezoelectric ceramics plates is undesirable as it may interfere with the operation of transducers. 1-3 piezoelectric composites are promising candidates to suppress the spurious modes mentioned above. However, theoretical modelling of multiphase ceramic composite objects is very complex. In this study, a simple analytical TSt vibration model is constructed from three-dimensional equations of linear piezoelectricity. The mechanical damping is considered in the model by introducing a complex elastic constant. The performance of 1-3 piezoelectric composites is analysed and the electrical impedance results from theoretical and experimental analysis are compared. The results show that there is excellent agreement between the experimental electrical impedance and that obtained by the theoretical TSt vibration analysis. This indicates that 1-3 piezoelectric composites can be operated in a nearly pure TSt vibration mode near the fundamental resonance. The analytical model we present is valid for analysing 1-3 piezoelectric composites plates with large aspect ratios quickly and efficiently.

  4. Experimental and simulation characterisation of flexural vibration modes in unimorph ultrasound transducers.

    Science.gov (United States)

    Eriksson, T J R; Ramadas, S N; Dixon, S M

    2016-02-01

    A unimorph flexural transducer design is proposed and tested with regard to mode shapes and frequencies. The transducers consist of a passive metal cap structure, and a thin piezoelectric disc, rigidly bonded to the inside. Extensive finite element (FE) modelling, and experimental 2D, time-resolved displacement measurements were done to characterise the transducers flexural properties, and to compare them to the analytical solutions of thin vibrating plates. Emphasis was put on characterising the passive layer of the unimorph structure, before bonding the piezoelectric element, to understand how the active element affects the behaviour of the flexing plate. A high power Nd:YAG laser was used to actuate the metal plate (non-contact), and the frequency content of the resulting displacement signal was analysed to identify the flexural modes. The non-axisymmetric modes, which are conventionally disregarded because of their unfavourable acoustic properties, were also taken into account. There was excellent agreement between the experimental results and the FE simulation data. There was good agreement with the analytical edge clamped plate model, but with some notable deviations, which have not previously been identified or commented upon. Specifically, the second axisymmetric mode is split into three separate modes, which is not explained by the traditional theory of vibrating plates. Crown Copyright © 2015. Published by Elsevier B.V. All rights reserved.

  5. Identification of surface species by vibrational normal mode analysis. A DFT study

    Science.gov (United States)

    Zhao, Zhi-Jian; Genest, Alexander; Rösch, Notker

    2017-10-01

    Infrared spectroscopy is an important experimental tool for identifying molecular species adsorbed on a metal surface that can be used in situ. Often vibrational modes in such IR spectra of surface species are assigned and identified by comparison with vibrational spectra of related (molecular) compounds of known structure, e. g., an organometallic cluster analogue. To check the validity of this strategy, we carried out a computational study where we compared the normal modes of three C2Hx species (x = 3, 4) in two types of systems, as adsorbates on the Pt(111) surface and as ligands in an organometallic cluster compound. The results of our DFT calculations reproduce the experimental observed frequencies with deviations of at most 50 cm-1. However, the frequencies of the C2Hx species in both types of systems have to be interpreted with due caution if the coordination mode is unknown. The comparative identification strategy works satisfactorily when the coordination mode of the molecular species (ethylidyne) is similar on the surface and in the metal cluster. However, large shifts are encountered when the molecular species (vinyl) exhibits different coordination modes on both types of substrates.

  6. Analytical Harmonic Vibrational Frequencies for the Green Fluorescent Protein Computed with ONIOM: Chromophore Mode Character and Its Response to Environment.

    Science.gov (United States)

    Thompson, Lee M; Lasoroski, Aurélie; Champion, Paul M; Sage, J Timothy; Frisch, Michael J; van Thor, Jasper J; Bearpark, Michael J

    2014-02-11

    A systematic comparison of different environmental effects on the vibrational modes of the 4-hydroxybenzylidene-2,3-dimethylimidazolinone (HBDI) chromophore using the ONIOM method allows us to model how the molecule's spectroscopic transitions are modified in the Green Fluorescent Protein (GFP). ONIOM(QM:MM) reduces the expense of normal mode calculations when computing the majority of second derivatives only at the MM level. New developments described here for the efficient solution of the CPHF equations, including contributions from electrostatic interactions with environment charges, mean that QM model systems of ∼100 atoms can be embedded within a much larger MM environment of ∼5000 atoms. The resulting vibrational normal modes, their associated frequencies, and dipole derivative vectors have been used to interpret experimental difference spectra (GFPI2-GFPA), chromophore vibrational Stark shifts, and changes in the difference between electronic and vibrational transition dipoles (mode angles) in the protein environment.

  7. Normal-mode characteristics of chlorophyll models. Vibrational analysis of metallooctaethylchlorins and their selectively deuterated analogues

    Energy Technology Data Exchange (ETDEWEB)

    Fonda, H.N.; Oertling, W.A.; Salehi, A.; Chang, C.K.; Babcock, G.T. (Michigan State Univ., East Lansing (United States))

    1990-12-19

    The resonance Raman (RR) and infrared (IR) spectra of the Zn, Cu, and Ni complexes of trans-octaethylchlorin (OEC) reveal significant differences in the vibrational-mode properties of metallochlorins and metalloporphyrins. Modes with a contribution from the C{sub a}C{sub m} stretching coordinate are distinguished by their sensitivity to metal substitution and to selective d{sub 2} and d{sub 4} methine deuteration. Comparison of the resonance Raman spectrum of CuOEC with that of CuECI (ECI = etiochlorin I) identifies those modes with a contribution from C{sub b}C{sub b} and C{sub b}C{sub s} stretching and C{sub b}C{sub s} bending coordinates. The results obtained show that there is substantial mixing of C{sub a}C{sub m} and C{sub b}C{sub b} stretching character in the high-frequency modes of MOEC. The suggestion that the symmetry reduction that occurs in metallochlorins relative to metalloporphyrins produces vibrational-mode localization to specific hemispheres or quadrants of the macrocycle has been tested and confirmed by specific d{sub 2} deuteration at the methine carbons. Resonance Raman spectra of CuOEP-d{sub 2} (OEP = octaethylporphyrin) and CuOEP-d{sub 4} establish that, for a delocalized mode, methine d{sub 2} deuteration can be expected to produce half the d{sub 4} shift. For CuOEC, selective deuteration at the {alpha}{beta} and {gamma},{delta} methine positions causes different patterns of frequency shifts that indicate the extent of mode localization.

  8. Raman spectra of vibrational and librational modes in methane clathrate hydrates using density functional theory

    Science.gov (United States)

    Ramya, K. R.; Pavan Kumar, G. V.; Venkatnathan, Arun

    2012-05-01

    The sI type methane clathrate hydrate lattice is formed during the process of nucleation where methane gas molecules are encapsulated in the form of dodecahedron (512CH4) and tetrakaidecahedron (51262CH4) water cages. The characterization of change in the vibrational modes which occur on the encapsulation of CH4 in these cages plays a key role in understanding the formation of these cages and subsequent growth to form the hydrate lattice. In this present work, we have chosen the density functional theory (DFT) using the dispersion corrected B97-D functional to characterize the Raman frequency vibrational modes of CH4 and surrounding water molecules in these cages. The symmetric and asymmetric C-H stretch in the 512CH4 cage is found to shift to higher frequency due to dispersion interaction of the encapsulated CH4 molecule with the water molecules of the cages. However, the symmetric and asymmetric O-H stretch of water molecules in 512CH4 and 51262CH4 cages are shifted towards lower frequency due to hydrogen bonding, and interactions with the encapsulated CH4 molecules. The CH4 bending modes in the 512CH4 and 51262CH4 cages are blueshifted, though the magnitude of the shifts is lower compared to modes in the high frequency region which suggests bending modes are less affected on encapsulation of CH4. The low frequency librational modes which are collective motion of the water molecules and CH4 in these cages show a broad range of frequencies which suggests that these modes largely contribute to the formation of the hydrate lattice.

  9. Mathematical model for calculation of the heat-hydraulic modes of heating points of heat-supplying systems

    Science.gov (United States)

    Shalaginova, Z. I.

    2016-03-01

    The mathematical model and calculation method of the thermal-hydraulic modes of heat points, based on the theory of hydraulic circuits, being developed at the Melentiev Energy Systems Institute are presented. The redundant circuit of the heat point was developed, in which all possible connecting circuits (CC) of the heat engineering equipment and the places of possible installation of control valve were inserted. It allows simulating the operating modes both at central heat points (CHP) and individual heat points (IHP). The configuration of the desired circuit is carried out automatically by removing the unnecessary links. The following circuits connecting the heating systems (HS) are considered: the dependent circuit (direct and through mixing elevator) and independent one (through the heater). The following connecting circuits of the load of hot water supply (HWS) were considered: open CC (direct water pumping from pipelines of heat networks) and a closed CC with connecting the HWS heaters on single-level (serial and parallel) and two-level (sequential and combined) circuits. The following connecting circuits of the ventilation systems (VS) were also considered: dependent circuit and independent one through a common heat exchanger with HS load. In the heat points, water temperature regulators for the hot water supply and ventilation and flow regulators for the heating system, as well as to the inlet as a whole, are possible. According to the accepted decomposition, the model of the heat point is an integral part of the overall heat-hydraulic model of the heat-supplying system having intermediate control stages (CHP and IHP), which allows to consider the operating modes of the heat networks of different levels connected with each other through CHP as well as connected through IHP of consumers with various connecting circuits of local systems of heat consumption: heating, ventilation and hot water supply. The model is implemented in the Angara data

  10. A new fuzzy sliding mode controller for vibration control systems using integrated-structure smart dampers

    Science.gov (United States)

    Dzung Nguyen, Sy; Kim, Wanho; Park, Jhinha; Choi, Seung-Bok

    2017-04-01

    Vibration control systems using smart dampers (SmDs) such as magnetorheological and electrorheological dampers (MRD and ERD), which are classified as the integrated structure-SmD control systems (ISSmDCSs), have been actively researched and widely used. This work proposes a new controller for a class of ISSmDCSs in which high accuracy of SmD models as well as increment of control ability to deal with uncertainty and time delay are to be expected. In order to achieve this goal, two formualtion steps are required; a non-parametric SmD model based on an adaptive neuro-fuzzy inference system (ANFIS) and a novel fuzzy sliding mode controller (FSMC) which can weaken the model error of the ISSmDCSs and hence provide enhanced vibration control performances. As for the formulation of the proposed controller, first, an ANFIS controller is desgned to identify SmDs using the improved control algorithm named improved establishing neuro-fuzzy system (establishing neuro-fuzzy system). Second, a new control law for the FSMC is designed via Lyapunov stability analysis. An application to a semi-active MRD vehicle suspension system is then undertaken to illustrate and evaluate the effectiveness of the proposed control method. It is demonstrated through an experimental realization that the FSMC proposed in this work shows superior vibration control performance of the vehicle suspension compared to other surveyed controller which have similar structures to the FSMC, such as fuzzy logic and sliding mode control.

  11. Approximate natural vibration analysis of rectangular plates with openings using assumed mode method

    Directory of Open Access Journals (Sweden)

    Dae Seung Cho

    2013-09-01

    Full Text Available Natural vibration analysis of plates with openings of different shape represents an important issue in naval architecture and ocean engineering applications. In this paper, a procedure for vibration analysis of plates with openings and arbitrary edge constraints is presented. It is based on the assumed mode method, where natural frequencies and modes are determined by solving an eigenvalue problem of a multi-degree-of-freedom system matrix equation derived by using Lagrange's equations of motion. The presented solution represents an extension of a procedure for natural vibration analysis of rectangular plates without openings, which has been recently presented in the literature. The effect of an opening is taken into account in an intuitive way, i.e. by subtracting its energy from the total plate energy without opening. Illustrative numerical examples include dynamic analysis of rectangular plates with rectangular, elliptic, circular as well as oval openings with various plate thicknesses and different combinations of boundary conditions. The results are compared with those obtained by the finite element method (FEM as well as those available in the relevant literature, and very good agreement is achieved.

  12. High-sensitivity monitoring of micromechanical vibration using optical whispering gallery mode resonators

    Energy Technology Data Exchange (ETDEWEB)

    Schliesser, A; Anetsberger, G; Riviere, R; Arcizet, O; Kippenberg, T J [Max-Planck-Institut fuer Quantenoptik, Hans-Kopfermann-Strasse 1, 85748 Garching (Germany)], E-mail: tjk@mpq.mpg.de

    2008-09-15

    The inherent coupling of optical and mechanical modes in high finesse optical microresonators provides a natural, highly sensitive transduction mechanism for micromechanical vibration. Using homodyne and polarization spectroscopy techniques, we achieve shot-noise limited displacement sensitivities of 10{sup -19} m Hz{sup -1/2}. In an unprecedented manner, this enables the detection and study of a variety of mechanical modes, which are identified as radial breathing, flexural and torsional modes using three-dimensional finite element modeling. Furthermore, a broadband equivalent displacement noise is measured and found to agree well with models for thermorefractive noise in silica dielectric cavities. Implications for ground-state cooling, displacement sensing and Kerr squeezing are discussed.

  13. A procedure obtaining stiffnesses and masses of a structure from vibration modes and substructure static test data

    Science.gov (United States)

    Edighoffer, H. H.

    1979-01-01

    A component mode desynthesis procedure is developed for determining the unknown vibration characteristics of a structural component (i.e., a launch vehicle) given the vibration characteristics of a structural system composed of that component combined with a known one (i.e., a payload). At least one component static test has to be performed. These data are used in conjunction with the system measured frequencies and mode shapes to obtain the vibration characteristics of each component. The flight dynamics of an empty launch vehicle can be determined from measurements made on a vehicle/payload combination in conjunction with a static test on the payload.

  14. Experimental Study of Flexible Plate Vibration Control by Using Two-Loop Sliding Mode Control Strategy

    Science.gov (United States)

    Yang, Jingyu; Lin, Jiahui; Liu, Yuejun; Yang, Kang; Zhou, Lanwei; Chen, Guoping

    2017-08-01

    It is well known that intelligent control theory has been used in many research fields, novel modeling method (DROMM) is used for flexible rectangular active vibration control, and then the validity of new model is confirmed by comparing finite element model with new model. In this paper, taking advantage of the dynamics of flexible rectangular plate, a two-loop sliding mode (TSM) MIMO approach is introduced for designing multiple-input multiple-output continuous vibration control system, which can overcome uncertainties, disturbances or unstable dynamics. An illustrative example is given in order to show the feasibility of the method. Numerical simulations and experiment confirm the effectiveness of the proposed TSM MIMO controller.

  15. Effects of poroelastic coefficients on normal vibration modes in vocal-fold tissues.

    Science.gov (United States)

    Tao, Chao; Liu, Xiaojun

    2011-02-01

    The vocal-fold tissue is treated as a transversally isotropic fluid-saturated porous material. Effects of poroelastic coefficients on eigenfrequencies and eigenmodes of the vocal-fold vibration are investigated using the Ritz method. The study demonstrates that the often-used elastic model is only a particular case of the poroelastic model with an infinite fluid-solid mass coupling parameter. The elastic model may be considered appropriate for the vocal-fold tissue when the absolute value of the fluid-solid mass coupling parameter is larger than 10(5) kg/m(3). Otherwise, the poroelastic model may be more accurate. The degree of compressibility of the vocal tissue can also been described by the poroelastic coefficients. Finally, it is revealed that the liquid and solid components in a poroelastic model could have different modal shapes when the coupling between them is weak. The mode decoupling could cause desynchronization and irregular vibration of the folds.

  16. Goos-Hänchen effect for optical vibrational modes in a semiconductor structure

    Science.gov (United States)

    Villegas, Diosdado; Arriaga, J.; de León-Pérez, Fernando; Pérez-Álvarez, R.

    2017-03-01

    We study the tunneling of optical vibrational modes with transverse horizontal polarization that impinge, at a given angle, on a semiconductor heterostructure. We find a large influence of the Goos-Hänchen shift on tunneling times. In particular, a Goos-Hänchen shift larger than the barrier thickness is reported for the first time. The relation between Goos-Hänchen and Hartman effects is also discussed. The identity that equals the dwell time to the sum of transmission and interference times, previously derived for one-dimensional tunneling problems, is extended to the two-dimensional case. Closed-form expressions are developed for the relevant quantities. Instead of using the standard approach, the interference time is computed from the vibrational energy density. The present study could be useful for the design of semiconductor devices.

  17. Vibration Modes at Terahertz and Infrared Frequencies of Ionic Liquids Consisting of an Imidazolium Cation and a Halogen Anion.

    Science.gov (United States)

    Yamada, Toshiki; Tominari, Yukihiro; Tanaka, Shukichi; Mizuno, Maya; Fukunaga, Kaori

    2014-11-17

    The terahertz and infrared frequency vibration modes of room-temperature ionic liquids with imidazolium cations and halogen anions were extensively investigated. There is an intermolecular vibrational mode between the imidazolium ring of an imidazolium cation, a halogen atomic anion with a large absorption coefficient and a broad bandwidth in the low THz frequency region (13-130 cm(-1)), the intramolecular vibrational modes of the alkyl-chain part of an imidazolium cation with a relatively small absorption coefficient in the mid THz frequency region (130-500 cm(-1)), the intramolecular skeletal vibrational modes of an imidazolium ring affected by the interaction between the imidazolium ring, and a halogen anion with a relatively large absorption coefficient in a high THz frequency region (500-670 cm(-1)). Interesting spectroscopic features on the interaction between imidazolium cations and halogen anions was also obtained from spectroscopic studies at IR frequencies (550-3300 cm(-1)). As far as the frequency of the intermolecular vibrational mode is concerned, we found the significance of the reduced mass in determining the intermolecular vibration frequency.

  18. A disk-pivot structure micro piezoelectric actuator using vibration mode B11.

    Science.gov (United States)

    Chu, Xiangcheng; Ma, Long; Li, Longtu

    2006-12-22

    Micro piezoelectric actuator using vibration mode B(11) (B(mn), where m is the number of nodal circles, n is the nodal diameters) is designed. Different from conventional wobble-type ultrasonic motor using piezoelectric rod or cylinder, piezoelectric disc is used to excite wobble modes and metal cylinder stator is used to amplify the transverse displacement, metal rod rotor is actuated to rotate. The outer diameter of the actuator is 14mm. There are features such as low drive voltage, micromation, and convenient control of wobble state by modifying the structure of stator, etc. Finite element analysis (FEA) of the stator has been made. It is found that the resonant frequency of vibration mode B(11) is 49.03kHz, which is measured at 45.7kHz by the laser vibrometer and impedance analyzer. The rotation speed has been measured, which could be as high as 10,071rpm under an alternating current 100V. Such piezoelectric actuator can be optimized and adjusted to fit practical conditions. It can be applied in the fields of precise instrument, bioengineering and other micro actuator system.

  19. Observation of the low frequency vibrational modes of bacteriophage M13 in water by Raman spectroscopy

    Directory of Open Access Journals (Sweden)

    Tsen Shaw-Wei D

    2006-09-01

    Full Text Available Abstract Background Recently, a technique which departs radically from conventional approaches has been proposed. This novel technique utilizes biological objects such as viruses as nano-templates for the fabrication of nanostructure elements. For example, rod-shaped viruses such as the M13 phage and tobacco mosaic virus have been successfully used as biological templates for the synthesis of semiconductor and metallic nanowires. Results and discussion Low wave number (≤ 20 cm-1 acoustic vibrations of the M13 phage have been studied using Raman spectroscopy. The experimental results are compared with theoretical calculations based on an elastic continuum model and appropriate Raman selection rules derived from a bond polarizability model. The observed Raman mode has been shown to belong to one of the Raman-active axial torsion modes of the M13 phage protein coat. Conclusion It is expected that the detection and characterization of this low frequency vibrational mode can be used for applications in nanotechnology such as for monitoring the process of virus functionalization and self-assembly. For example, the differences in Raman spectra can be used to monitor the coating of virus with some other materials and nano-assembly process, such as attaching a carbon nanotube or quantum dots.

  20. Influence of controlling vibrations on heat transfer in floating zone crystal growth*

    Science.gov (United States)

    Fedyushkin, A. I.

    The crystal growth processes of monocrystals are strongly vibrational sensitive systems and in particular it concerns to a floating zone method as presence of a free surface and two fronts of crystallization and melting that aggravate it The given work is devoted to numerical investigations of the influence of controlling vibrations on heat transfer during crystal growth by floating zone technique Normal and weightless environment conditions are considered Mathematical simulation is performed on the numerical solutions of basis unsteady Navier-Stokes equations for incompressible fluid flows and energy equation 2D axisymmetric geometry was used in model Marangoni convection and radiation condition on the curvature free surface were taken in account The calculations of the shape of a free surface of a liquid zone and influences on it of a corner of wetting force of weight and size of factor of a superficial tension are carried out The simulations of convective heat transfer for real curvature free surface of a liquid zone with and without the taking into account of the following factors parameters of radiation rotations natural and Marangoni convection and vibrations are carried out The given calculations are carried out for semiconductors melts with Prandtl number Pr 1 and for oxides Pr 1 The influence of vibrations of a crystal on melt flow and on the wide of dynamic and thermal boundary layers at melt-crystal interface is studied The action of vibrations on an enhancement of heat fluxes at the melt crystal interface is shown

  1. Seven Operation Modes and Simulation Models of Solar Heating System with PCM Storage Tank

    Directory of Open Access Journals (Sweden)

    Juan Zhao

    2017-12-01

    Full Text Available A physical model and dynamic simulation models of a solar phase-change heat storage heating system with a plate solar collector, phase-change material (PCM storage tank, plate heat exchanger, and auxiliary heat sources were established. A control strategy and numerical models for each of seven different operation modes that cover the entire heating season of the system were developed for the first time. The seven proposed operation modes are Mode 1: free cooling; Mode 2: reservation of heat absorbed by the solar collector in the PCM storage tank when there is no heating demand; Mode 3: direct supply of the heating demand by the solar collector; Mode 4: use of the heat absorbed by the solar collector to meet the heating demands, with the excess heat stored in the PCM storage tank; Mode 5: use of heat stored in the PCM storage tank to meet the heating demands, Mode 6: combined use of heat stored in the PCM storage tank and the auxiliary heating sources to meet the heating demands; and Mode 7: exclusive use of the auxiliary heat sources in order to meet the heating demands. Mathematical models were established for each of the above seven operation modes, taking into consideration the effects of the outdoor meteorological parameters and terminal load on the heating system. The real-time parameters for the entire heating season of the system with respect to the different operation modes can be obtained by solving the simulation models, and used as reference for the optimal design and operation of the actual system.

  2. Vibrational Spectra and Heat Capacity of Methane, and the Speed of Sound

    Science.gov (United States)

    Tennis, Ronald; Bailey, Ryan; Henderson, Giles

    2000-12-01

    A two-part physical chemistry laboratory experiment is described in which students evaluate statistical mechanical theory by comparing a measured speed of sound and heat capacity with values predicted from vibrational spectra. In part 1 students measure the IR spectrum of CH4(g) and the Raman spectrum of CH4(l) to determine quantized vibrational energy spacings. Strong Raman scattering of a pulsed nitrogen laser beam is observed with a liquid methane sample in a custom cryogenic cell constructed from two side-arm test tubes and a length of Pyrex tube. These data are used with the statistical mechanics of a harmonic oscillator to calculate vibrational heat capacities and CP/CV; of CH4(g) and the speed of sound in CH4(g). In part 2, the predicted speed of sound is compared with an experimental value measured with a simple acoustic resonance cavity (Kundt's tube) exhausted to a Bunsen burner.

  3. Plasma heating via electron Bernstein wave heating using ordinary and extraodinary mode

    Directory of Open Access Journals (Sweden)

    A. Parvazian

    2008-03-01

    Full Text Available Magnetically confined plasma can be heated with high power microwave sources. In spherical torus the electron plasma frequency exeeds the electron cyclotron frequency (EC and, as a consequence, electromagnetic waves at fundamental and low harmonic EC cannot propagate within the plasma. In contrast, electron Bernstein waves (EBWs readily propagate in spherical torus plasma and are absorbed strongly at the electron cyclotron resonances. In order to proagate EBWs beyond the upper hybrid resonance (UHR, that surrounds the plasma, the EBWs must convert via one of two processes to either ordinary (O-mode or extraordinary (X-mode electromagnetic waves. O-mode and X-mode electromagnetic waves lunched at the plasma edge can convert to the electron Bernstein waves (EBWs which can propagate without and cut-off into the core of the plasma and damp on electrons. Since the electron Bernstein wave (EBW has no cut-off limits, it is well suited to heat an over-dense plasma by resonant absorption. An important problem is to calculate mode conversion coefficient that is very sensitive to density. Mode conversion coefficient depends on Budden parameter ( ñ and density scale length (Ln in upper hybrid resonance (UHR. In Mega Ampere Spherical Tokamak (MAST, the optimized conversion efficiency approached 72.5% when Ln was 4.94 cm and the magnetic field was 0.475 Tesla in the core of the plasma.

  4. Sparse Representation Based Frequency Detection and Uncertainty Reduction in Blade Tip Timing Measurement for Multi-Mode Blade Vibration Monitoring

    Science.gov (United States)

    Pan, Minghao; Yang, Yongmin; Guan, Fengjiao; Hu, Haifeng; Xu, Hailong

    2017-01-01

    The accurate monitoring of blade vibration under operating conditions is essential in turbo-machinery testing. Blade tip timing (BTT) is a promising non-contact technique for the measurement of blade vibrations. However, the BTT sampling data are inherently under-sampled and contaminated with several measurement uncertainties. How to recover frequency spectra of blade vibrations though processing these under-sampled biased signals is a bottleneck problem. A novel method of BTT signal processing for alleviating measurement uncertainties in recovery of multi-mode blade vibration frequency spectrum is proposed in this paper. The method can be divided into four phases. First, a single measurement vector model is built by exploiting that the blade vibration signals are sparse in frequency spectra. Secondly, the uniqueness of the nonnegative sparse solution is studied to achieve the vibration frequency spectrum. Thirdly, typical sources of BTT measurement uncertainties are quantitatively analyzed. Finally, an improved vibration frequency spectra recovery method is proposed to get a guaranteed level of sparse solution when measurement results are biased. Simulations and experiments are performed to prove the feasibility of the proposed method. The most outstanding advantage is that this method can prevent the recovered multi-mode vibration spectra from being affected by BTT measurement uncertainties without increasing the probe number. PMID:28758952

  5. Resonant electron-impact excitation of vibrational modes in polyatomic molecules

    Science.gov (United States)

    Cartwright, David C.; Trajmar, Sandor

    1996-04-01

    Measured differential cross sections (DCSs) for electron-impact excitation of bending vibrational modes involving an odd number of vibrational quanta in 0953-4075/29/8/018/img5 by 4 eV incident energy electrons display a strong trend to zero for forward and backward scattering which is characteristic of `symmetry-forbidden' transitions. This DCS behaviour is postulated here to be produced by a Feshbach resonant mechanism involving a low-lying bent excited state of 0953-4075/29/8/018/img5. The model described here identifies three additional low-lying bent excited states of 0953-4075/29/8/018/img5 which could also be parent states for core-excited Feshbach resonances, one of which may play a role in dissociative attachment in this 3.5 - 5.0 eV energy region. The resonant vibrational excitation mechanism proposed here is also believed to be operative in other polyatomic molecules and could be investigated by performing selected electron energy-loss measurements within the lowest energy resonance regions of the molecules 0953-4075/29/8/018/img8 and 0953-4075/29/8/018/img9.

  6. Ultrasensitive broadband probing of molecular vibrational modes with multifrequency optical antennas.

    Science.gov (United States)

    Aouani, Heykel; Šípová, Hana; Rahmani, Mohsen; Navarro-Cia, Miguel; Hegnerová, Kateřina; Homola, Jiří; Hong, Minghui; Maier, Stefan A

    2013-01-22

    Optical antennas represent an enabling technology for enhancing the detection of molecular vibrational signatures at low concentrations and probing the chemical composition of a sample in order to identify target molecules. However, efficiently detecting different vibrational modes to determine the presence (or the absence) of a molecular species requires a multispectral interrogation in a window of several micrometers, as many molecules present informative fingerprint spectra in the mid-infrared between 2.5 and 10 μm. As most nanoantennas exhibit a narrow-band response because of their dipolar nature, they are not suitable for such applications. Here, we propose the use of multifrequency optical antennas designed for operating with a bandwidth of several octaves. We demonstrate that surface-enhanced infrared absorption gains in the order of 10(5) can be easily obtained in a spectral window of 3 μm with attomolar concentrations of molecules, providing new opportunities for ultrasensitive broadband detection of molecular species via vibrational spectroscopy techniques.

  7. Sub-THz spectroscopic characterization of vibrational modes in artificially designed DNA monocrystal

    Science.gov (United States)

    Sizov, Igor; Rahman, Masudur; Gelmont, Boris; Norton, Michael L.; Globus, Tatiana

    2013-11-01

    Sub-terahertz (sub-THz) vibrational spectroscopy is a new spectroscopic branch for characterizing biological macromolecules. In this work, highly resolved sub-THz resonance spectroscopy is used for characterizing engineered molecular structures, an artificially designed DNA monocrystal, built from a short DNA sequence. Using a recently developed frequency domain spectroscopic instrument operating at room temperature with high spectral and spatial resolution, we demonstrated very intense and specific spectral lines from a DNA crystal in general agreement with a computational molecular dynamics (MD) simulation of a short double stranded DNA fragment. The spectroscopic signature measured in the frequency range between 310 and 490 GHz is rich in well resolved and reproducible spectral features thus demonstrating the capability of THz resonance spectroscopy to be used for characterizing custom macromolecules and structures designed and implemented via nanotechnology for a wide variety of application domains. Analysis of MD simulation indicates that intense and narrow vibrational modes with atomic movements perpendicular (transverse) and parallel (longitudinal) to the long DNA axis coexist in dsDNA, with much higher contribution from longitudinal vibrations.

  8. Experimental and theoretical model of reactivity and vibrational detection modes of triacetone triperoxide (TATP) and homologues

    Science.gov (United States)

    Pacheco-Londono, Leonardo C.; Primera-Pedrozo, Oliva M.; Hernandez-Rivera, Samuel P.

    2004-12-01

    Fully optimized molecular geometry, parameters of reactivity and vibrational spectra of triacetone triperoxide (TATP) and homologue organic peroxides were calculated using B3LYP/6-31G(d,p) method within the Density Functional Theory formalism. Infrared and Raman Spectroscopy were utilized to obtain vibrational spectra of the energetic compound. The model consists in the relation found between the Raman Shift location of the important symmetric stretch ν(O-O) of the organic peroxides and the reactivity of the organic peroxides. A good correlation between the band location in the series studied and the x-y plane polarizability component and the ionization energy was found. Gas phase IR absorption of TATP in air was used for developing stand-off detection schemes of the important organic peroxide in air. The sublimation properties of TATP were measured using two methods: Grazing Angle Probe-Fiber Coupled FTIR and gravimetric on stainless steel surfaces. Sublimation rates, loading concentration values and absorbance band areas were measured and modeled using the persistent IR vibrational signature of the ν(C-O) mode.

  9. Application of empirical mode decomposition method for characterization of random vibration signals

    Directory of Open Access Journals (Sweden)

    Setyamartana Parman

    2016-07-01

    Full Text Available Characterization of finite measured signals is a great of importance in dynamical modeling and system identification. This paper addresses an approach for characterization of measured random vibration signals where the approach rests on a method called empirical mode decomposition (EMD. The applicability of proposed approach is tested in one numerical and experimental data from a structural system, namely spar platform. The results are three main signal components, comprising: noise embedded in the measured signal as the first component, first intrinsic mode function (IMF called as the wave frequency response (WFR as the second component and second IMF called as the low frequency response (LFR as the third component while the residue is the trend. Band-pass filter (BPF method is taken as benchmark for the results obtained from EMD method.

  10. Semi-active damping with negative stiffness for multi-mode cable vibration mitigation: approximate collocated control solution

    Science.gov (United States)

    Weber, F.; Distl, H.

    2015-11-01

    This paper derives an approximate collocated control solution for the mitigation of multi-mode cable vibration by semi-active damping with negative stiffness based on the control force characteristics of clipped linear quadratic regulator (LQR). The control parameters are derived from optimal modal viscous damping and corrected in order to guarantee that both the equivalent viscous damping coefficient and the equivalent stiffness coefficient of the semi-active cable damper force are equal to their desired counterparts. The collocated control solution with corrected control parameters is numerically validated by free decay tests of the first four cable modes and combinations of these modes. The results of the single-harmonic tests demonstrate that the novel approach yields 1.86 times more cable damping than optimal modal viscous damping and 1.87 to 2.33 times more damping compared to a passive oil damper whose viscous damper coefficient is optimally tuned to the targeted mode range of the first four modes. The improvement in case of the multi-harmonic vibration tests, i.e. when modes 1 and 3 and modes 2 and 4 are vibrating at the same time, is between 1.55 and 3.81. The results also show that these improvements are obtained almost independent of the cable anti-node amplitude. Thus, the proposed approximate real-time applicable collocated semi-active control solution which can be realized by magnetorheological dampers represents a promising tool for the efficient mitigation of stay cable vibrations.

  11. Comparison of resonance frequencies between normal and tangential vibration modes of graphene-nanoribbon-resonators.

    Science.gov (United States)

    Kwon, Oh Kuen; Hwang, Ho Jung; Park, Jungcheol

    2013-12-01

    We investigate tunable graphene-nanoribbon (GNR)-resonators actuated in the tangential direction, and their properties are compared to those actuated in the normal direction, via classical molecular dynamics simulations. These GNR-resonators can be tuned both by the initial strain and the gate. The relationships between the frequency-versus-gate and the initial strain in this work are in good agreement with those in previous experimental works. With increasing initial strain, the resonance frequencies are greatly upshifted, whereas the tunable ranges in frequency are greatly decreased. The tunability in the dynamic operating range decreases with increasing initial strain. For very small strains, the GNR-resonators have large dynamic operating ranges in the normal vibration mode, and for large strains, the GNR-resonators have higher operating frequencies in the tangential vibration mode. The resonance frequencies are estimated by a classical continuum model, with tension acting on the GNR-resonators consisting of both initial tension by initial strain and induced tension by gate actuating.

  12. Can Internal Conversion BE Controlled by Mode-Specific Vibrational Excitation in Polyatomic Molecules

    Science.gov (United States)

    Portnov, Alexander; Epshtein, Michael; Bar, Ilana

    2017-06-01

    Nonadiabatic processes, dominated by dynamic passage of reactive fluxes through conical intersections (CIs) are considered to be appealing means for manipulating reaction paths. One approach that is considered to be effective in controlling the course of dissociation processes is the selective excitation of vibrational modes containing a considerable component of motion. Here, we have chosen to study the predissociation of the model test molecule, methylamine and its deuterated isotopologues, excited to well-characterized quantum states on the first excited electronic state, S_{1}, by following the N-H(D) bond fission dynamics through sensitive H(D) photofragment probing. The branching ratios between slow and fast H(D) photofragments, the internal energies of their counter radical photofragments and the anisotropy parameters for fast H photofragments, confirm correlated anomalies for predissociation initiated from specific rovibronic states, reflecting the existence of a dynamic resonance in each molecule. This resonance strongly depends on the energy of the initially excited rovibronic states, the evolving vibrational mode on the repulsive S_{1} part during N-H(D) bond elongation, and the manipulated passage through the CI that leads to radicals excited with C-N-H(D) bending and preferential perpendicular bond breaking, relative to the photolyzing laser polarization, in molecules containing the NH_{2} group. The indicated resonance plays an important role in the bifurcation dynamics at the CI and can be foreseen to exist in other photoinitiated processes and to control their outcome.

  13. Experimental study on cross-flow induced vibrations in heat exchanger tube bundle

    Science.gov (United States)

    Khushnood, Shahab; Nizam, Luqman Ahmad

    2017-03-01

    Vibration in heat exchangers is one of the main problems that the industry has faced over last few decades. Vibration phenomenon in heat exchangers is of major concern for designers and process engineers since it can lead to the tube damage, tube leakage, baffle damage, tube collision damage, fatigue, creep etc. In the present study, vibration response is analyzed on single tube located in the centre of the tube bundle having parallel triangular arrangement (60°) with P/ D ratio of 1.44. The experiment is performed for two different flow conditions. This kind of experiment has not been reported in the literature. Under the first condition, the tube vibration response is analyzed when there is no internal flow in the tube and under the second condition, the response is analyzed when the internal tube flow is maintained at a constant value of 0.1 m/s. The free stream shell side velocity ranges from 0.8 m/s to 1.3 m/s, the reduced gap velocity varies from 1.80 to 2.66 and the Reynolds number varies from 44500 to 66000. It is observed that the internal tube flow results in larger vibration amplitudes for the tube than that without internal tube flow. It is also established that over the current range of shell side flow velocity, the turbulence is the dominant excitation mechanism for producing vibration in the tube since the amplitude varies directly with the increase in the shell side velocity. Damping has no significant effect on the vibration behavior of the tube for the current velocity range.

  14. C-H local modes in cyclobutene. II. Laser photoacoustic studies 10 000-17 000 cm-1. Vibrational structure and C-H local mode dynamics

    Science.gov (United States)

    Baggott, J. E.; Law, D. W.; Lightfoot, P. D.; Mills, I. M.

    1986-11-01

    In part I of this study [Baggott, Clase, and Mills, Spectrochim. Acta Part A 42, 319 (1986)] we presented FTIR spectra of gas phase cyclobutene and modeled the v=1-3 stretching states of both olefinic and methylenic C-H bonds in terms of a local mode model. In this paper we present some improvements to our original model and make use of recently derived ``x,K relations'' to find the equivalent normal mode descriptions. The use of both the local mode and normal mode approaches to modeling the vibrational structure is described in some detail. We present evidence for Fermi resonance interactions between the methylenic C-H stretch overtones and ring C-C stretch vibrations, revealed in laser photoacoustic spectra in the v=4-6 region. An approximate model vibrational Hamiltonian is proposed to explain the observed structure and is used to calculate the dynamics of the C-H stretch local mode decay resulting from interaction with lower frequency ring modes. The implications of our experimental and theoretical studies for mode-selective photochemistry are discussed briefly.

  15. Mode conversion in three ion species ICRF heating scenario

    Science.gov (United States)

    Lin, Y.; Edlund, E.; Ennever, P.; Porkolab, M.; Wright, J.; Wukitch, S.

    2016-10-01

    Three-ion species ICRF heating has been studied on Alcator C-Mod and on JET. It has been shown to heat the plasma and generate energetic particles. In a typical three-ion scenario, the plasma consists of 60-70% D, 30-40% H and a trace level (1% or less) of 3He. This species mixture creates two hybrid resonances (D-3He and 3He-H) in the plasma, in the vicinity of the 3He IC resonance (on both sides). The fast wave can undergo mode conversion (MC) to ion Bernstein waves and ion cyclotron waves at the two hybrid resonances. A phase contrast imaging (PCI) system has been used to measure the RF waves in the three-ion heating experiment. The experimentally measured MC locations and the separating distance between the two MC regions help to determine the concentration of the three species. The PCI signal amplitudes for the RF waves are found to be sensitive to RF and plasma parameters, including PRF, Te, ne and also the species mix concentration. The parameter dependences found in the experiment will be compared with ICRF code simulations. Supported by USDoE Awards DE-FC02-99ER54512 and DE-FG02-94-ER54235.

  16. Localized Edge Vibrations and Edge Reconstruction by Joule Heating in Graphene Nanostructures

    DEFF Research Database (Denmark)

    Engelund, Mads; Fürst, Joachim Alexander; Jauho, Antti-Pekka

    2010-01-01

    Control of the edge topology of graphene nanostructures is critical to graphene-based electronics. A means of producing atomically smooth zigzag edges using electronic current has recently been demonstrated in experiments [Jia et al., Science 323, 1701 (2009)]. We develop a microscopic theory...... for current-induced edge reconstruction using density functional theory. Our calculations provide evidence for localized vibrations at edge interfaces involving unpassivated armchair edges. We demonstrate that these vibrations couple to the current, estimate their excitation by Joule heating, and argue...

  17. Control of Chaos in Rate-Dependent Friction-Induced Vibration Using Adaptive Sliding Mode Control and Impulse Damper

    Directory of Open Access Journals (Sweden)

    Ehsan Maani Miandoab

    2013-01-01

    Full Text Available Two different control methods, namely, adaptive sliding mode control and impulse damper, are used to control the chaotic vibration of a block on a belt system due to the rate-dependent friction. In the first method, using the sliding mode control technique and based on the Lyapunov stability theory, a sliding surface is determined, and an adaptive control law is established which stabilizes the chaotic response of the system. In the second control method, the vibration of this system is controlled by an impulse damper. In this method, an impulsive force is applied to the system by expanding and contracting the PZT stack according to efficient control law. Numerical simulations demonstrate the effectiveness of both methods in controlling the chaotic vibration of the system. It is shown that the settling time of the controlled system using impulse damper is less than that one controlled by adaptive sliding mode control; however, it needs more control effort.

  18. Hydrogen Bonds and the Vibrational Modes of Water at Interfaces: ab-initio Molecular Dynamics meets Neutron Scattering

    Science.gov (United States)

    Kumar, Nitin; Neogi, Sanghamitra; Kent, Paul; Bandura, Andrei; Kubicki, James; Wesolowski, David; Sofo, Jorge

    2008-03-01

    We study the vibrational density of states (VDOS) of a thin water layer on the rutile (110) surface. The VDOS is obtained from the velocity-velocity autocorrelation function calculated from trajectories of large scale ab-initio molecular dynamics simulations. The rutile surface induces a shift to lower frequencies of the stretching modes with respect to pure water. The water vapor surface shows a peak at the vibrational frequency of free hydroxyls. Overall, the average stretching mode vibrational frequency increases with decreasing hydrogen bonding density. This density depends strongly on temperature. The water dissociation percentage at the surface can be correlated with the ratio between the weights of the stretching and the bending modes. Our results are in good agreement with inelastic neutron scattering measurements done on wet titania nanoparticles.

  19. Computational Modeling of the Size Effects on the Optical Vibrational Modes of H-Terminated Ge Nanostructures

    Directory of Open Access Journals (Sweden)

    Miguel Cruz-Irisson

    2013-04-01

    Full Text Available The vibrational dispersion relations of porous germanium (pGe and germanium nanowires (GeNWs were calculated using the ab initio density functional perturbation theory with a generalized gradient approximation with norm-conserving pseudopotentials. Both pores and nanowires were modeled using the supercell technique. All of the surface dangling bonds were saturated with hydrogen atoms. To address the difference in the confinement between the pores and the nanowires, we calculated the vibrational density of states of the two materials. The results indicate that there is a slight shift in the highest optical mode of the Ge-Ge vibration interval in all of the nanostructures due to the phonon confinement effects. The GeNWs exhibit a reduced phonon confinement compared with the porous Ge due to the mixed Ge-dihydride vibrational modes around the maximum bulk Ge optical mode of approximately 300 cm−1; however, the general effects of such confinements could still be noticed, such as the shift to lower frequencies of the highest optical mode belonging to the Ge vibrations.

  20. An investigation of the influence of heating modes on ignition and pyrolysis of woody wildland fuel

    Science.gov (United States)

    B.L. Yashwanth; B. Shotorban; S. Mahalingam; D.R. Weise

    2015-01-01

    The ignition of woody wildland fuel modeled as a one-dimensional slab subject to various modes of heating was investigated using a general pyrolysis code, Gpyro. The heating mode was varied by applying different convective and/or radiative, time-dependent heat flux boundary conditions on one end of the slab while keeping the other end insulated. Dry wood properties...

  1. Enhancing light-harvesting power with coherent vibrational interactions: A quantum heat engine picture.

    Science.gov (United States)

    Killoran, N; Huelga, S F; Plenio, M B

    2015-10-21

    Recent evidence suggests that quantum effects may have functional importance in biological light-harvesting systems. Along with delocalized electronic excitations, it is now suspected that quantum coherent interactions with certain near-resonant vibrations may contribute to light-harvesting performance. However, the actual quantum advantage offered by such coherent vibrational interactions has not yet been established. We investigate a quantum design principle, whereby coherent exchange of single energy quanta between electronic and vibrational degrees of freedom can enhance a light-harvesting system's power above what is possible by thermal mechanisms alone. We present a prototype quantum heat engine which cleanly illustrates this quantum design principle and quantifies its quantum advantage using thermodynamic measures of performance. We also demonstrate the principle's relevance in parameter regimes connected to natural light-harvesting structures.

  2. Enhancing light-harvesting power with coherent vibrational interactions: A quantum heat engine picture

    Energy Technology Data Exchange (ETDEWEB)

    Killoran, N.; Huelga, S. F.; Plenio, M. B. [Institut für Theoretische Physik, Universität Ulm, Albert-Einstein-Allee 11, D-89069 Ulm (Germany)

    2015-10-21

    Recent evidence suggests that quantum effects may have functional importance in biological light-harvesting systems. Along with delocalized electronic excitations, it is now suspected that quantum coherent interactions with certain near-resonant vibrations may contribute to light-harvesting performance. However, the actual quantum advantage offered by such coherent vibrational interactions has not yet been established. We investigate a quantum design principle, whereby coherent exchange of single energy quanta between electronic and vibrational degrees of freedom can enhance a light-harvesting system’s power above what is possible by thermal mechanisms alone. We present a prototype quantum heat engine which cleanly illustrates this quantum design principle and quantifies its quantum advantage using thermodynamic measures of performance. We also demonstrate the principle’s relevance in parameter regimes connected to natural light-harvesting structures.

  3. Vibration energy harvesting based on integrated piezoelectric components operating in different modes.

    Science.gov (United States)

    Hu, Junhui; Jong, Januar; Zhao, Chunsheng

    2010-01-01

    To increase the vibration energy-harvesting capability of the piezoelectric generator based on a cantilever beam, we have proposed a piezoelectric generator that not only uses the strain change of piezoelectric components bonded on a cantilever beam, but also employs the weights at the tip of the cantilever beam to hit piezoelectric components located on the 2 sides of weights. A prototype of the piezoelectric generator has been fabricated and its characteristics have been measured and analyzed. The experimental results show that the piezoelectric components operating in the hit mode can substantially enhance the energy harvesting of the piezoelectric generator on a cantilever beam. Two methods are used and compared in the management of rectified output voltages from different groups of piezoelectric components. In one of them, the DC voltages from rectifiers are connected in series, and then the total DC voltage is applied to a capacitor. In another connection, the DC voltage from each group is applied to different capacitors. It is found that 22.3% of the harvested energy is wasted due to the series connection. The total output electric energy of our piezoelectric generator at nonresonance could be up to 43 nJ for one vibration excitation applied by spring, with initial vibration amplitude (0-p) of 18 mm and frequency of 18.5 Hz, when the rectified voltages from different groups of piezoelectric components are connected to their individual capacitors. In addition, the motion and impact of the weights at the tip of the cantilever beam are theoretically analyzed, which well explains the experimental phenomena and suggests the measures to improve the generator.

  4. Terahertz spectroscopy and solid-state density functional theory calculation of anthracene: Effect of dispersion force on the vibrational modes

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Feng; Tominaga, Keisuke, E-mail: atmyh@ntu.edu.tw, E-mail: tominaga@kobe-u.ca.jp, E-mail: junichi.nishizawa@hanken.jp [Molecular Photoscience Research Center, Kobe University, Nada, Kobe 657-0013 (Japan); Hayashi, Michitoshi, E-mail: atmyh@ntu.edu.tw, E-mail: tominaga@kobe-u.ca.jp, E-mail: junichi.nishizawa@hanken.jp; Wang, Houng-Wei [Center for Condensed Matter Sciences, National Taiwan University, 1 Roosevelt Rd., Sec. 4, Taipei 10617, Taiwan (China); Kambara, Ohki; Sasaki, Tetsuo [Research Institute of Electronics, Shizuoka University, 3-5-1 Jyohoku, Naka-ku, Hamamatsu, Shizuoka 432-8561 (Japan); Nishizawa, Jun-ichi, E-mail: atmyh@ntu.edu.tw, E-mail: tominaga@kobe-u.ca.jp, E-mail: junichi.nishizawa@hanken.jp [Jun-ichi Nishizawa Memorial Research Center, Tohoku University, 519-1176 Aoba, Aramaki, Aoba-ku, Sendai 980-0845 (Japan)

    2014-05-07

    The phonon modes of molecular crystals in the terahertz frequency region often feature delicately coupled inter- and intra-molecular vibrations. Recent advances in density functional theory such as DFT-D{sup *} have enabled accurate frequency calculation. However, the nature of normal modes has not been quantitatively discussed against experimental criteria such as isotope shift (IS) and correlation field splitting (CFS). Here, we report an analytical mode-decoupling method that allows for the decomposition of a normal mode of interest into intermolecular translation, libration, and intramolecular vibrational motions. We show an application of this method using the crystalline anthracene system as an example. The relationship between the experimentally obtained IS and the IS obtained by PBE-D{sup *} simulation indicates that two distinctive regions exist. Region I is associated with a pure intermolecular translation, whereas region II features coupled intramolecular vibrations that are further coupled by a weak intermolecular translation. We find that the PBE-D{sup *} data show excellent agreement with the experimental data in terms of IS and CFS in region II; however, PBE-D{sup *} produces significant deviations in IS in region I where strong coupling between inter- and intra-molecular vibrations contributes to normal modes. The result of this analysis is expected to facilitate future improvement of DFT-D{sup *}.

  5. A magnetic damper for first mode vibration reduction in multimass flexible rotors

    Science.gov (United States)

    Kasarda, M. E. F.; Allaire, P. E.; Humphris, R. R.; Barrett, L. E.

    1989-01-01

    Many rotating machines such as compressors, turbines and pumps have long thin shafts with resulting vibration problems, and would benefit from additional damping near the center of the shaft. Magnetic dampers have the potential to be employed in these machines because they can operate in the working fluid environment unlike conventional bearings. An experimental test rig is described which was set up with a long thin shaft and several masses to represent a flexible shaft machine. An active magnetic damper was placed in three locations: near the midspan, near one end disk, and close to the bearing. With typical control parameter settings, the midspan location reduced the first mode vibration 82 percent, the disk location reduced it 75 percent and the bearing location attained a 74 percent reduction. Magnetic damper stiffness and damping values used to obtain these reductions were only a few percent of the bearing stiffness and damping values. A theoretical model of both the rotor and the damper was developed and compared to the measured results. The agreement was good.

  6. Complex modes of vibration due to small-scale damping in a guitar topplate

    Directory of Open Access Journals (Sweden)

    J. A. Torres

    2010-04-01

    Full Text Available Modal analysis is one of the preeminent methods used by scientists and engineers to study vibrating structures. The frequency responsefunctions obtained through this method, are, in general, complex-valued. There is, however, no agreed-upon interpretation given to thereal and imaginary parts of these functions, even though it is acknowledged that their relative magnitude for different frequencies is relatedto the behaviour of the corresponding modes. A simple model is deduced to describe the shape of the spectrum associated with afinite-length time-signal. There is very good agreement between results obtained using this model and numerical results obtained for,in this case, the vibration of a guitar top-plate using finite element methods. One interpretation of the relative magnitudes of the real and imaginary parts of the frequency response functions is advanced. It is found that stationary-wave behaviour is associated with the dominance of the real or imaginary part; traveling-wave behaviour, on the other hand, occurs when the real and imaginary parts are of the same order of magnitude, as long as the scale of damping is large enough and resonance peaks in the spectrum are close enough.

  7. Closed-Loop Input Shaping Control of Vibration in Flexible Structures via Adaptive Sliding Mode Control

    Directory of Open Access Journals (Sweden)

    Ming-Chang Pai

    2012-01-01

    Full Text Available Input shaping technique is widely used in reducing or eliminating residual vibration of flexible structures. The exact elimination of the residual vibration via input shaping technique depends on the amplitudes and instants of impulse application. However, systems always have parameter uncertainties which can lead to performance degradation. In this paper, a closed-loop input shaping control scheme is developed for uncertain flexible structures. The algorithm is based on input shaping control and adaptive sliding mode control. The proposed scheme does not need a priori knowledge of upper bounds on the norm of the uncertainties, but estimates them by using the adaptation technique. This scheme guarantees closed-loop system stability, and yields good performance and robustness in the presence of parameter uncertainties and external disturbances as well. Furthermore, it is shown that increasing the robustness to parameter uncertainties does not lengthen the duration of the impulse sequence. Simulation results demonstrate the efficacy of the proposed closed-loop input shaping control scheme.

  8. A simple method for designing structural models with closely spaced modes of vibration

    Science.gov (United States)

    Hallauer, W. L., Jr.; Weisshaar, T. A.; Shostak, A. G.

    1978-01-01

    A simple method for designing a mathematical model with closely spaced vibration modes is described. The design process begins with a reference model having specified geometry, continuous inertia and stiffness distributions, and degrees of freedom, all of which remain unchanged. Two natural frequencies of this model are then forced together by means of systematic perturbation of the model's discrete inertia and stiffness parameters. There is only one eigenvalue solution per design cycle, and the gradient vector is calculated directly from the resulting modal quantities. The minimization procedure employed is unconstrained. As applications, a cantilevered plane grid model with five degrees of freedom and a bending-torsion-oscillator with eleven degrees of freedom are treated.

  9. A comparison of several methods for the calculation of vibration mode shape derivatives

    Science.gov (United States)

    Sutter, T. R.; Camarda, C. J.; Walsh, J. L.; Adelman, H. M.

    1986-01-01

    Four methods for the calculation of derivatives of vibration mode shapes (eigenvectors) with respect to design parameters are reviewed and compared. These methods (finite difference method, Nelson's method, modal method and a modified modal method) are implemented in a general-purpose commercial finite element program and applied to a cantilever beam and a stiffened cylinder with a cutout. A beam tip mass, a beam root height and specific dimensions of the cylinder model comprise the design variables. Data are presented showing the amount of central processor time used to compute the first four eigenvector derivatives for each example problem; errors and rapidity of convergence of the approximate derivative to the exact derivative are taken into account. Nelson's method proved to be most reliable and efficient.

  10. Local vibration modes of shallow thermal donors in nitrogen-doped CZ silicon crystals

    Energy Technology Data Exchange (ETDEWEB)

    Inoue, N. [RIAST, Osaka Prefecture University, Sakai, 599-8570 (Japan) and Nitrogen Measurement WG, JEITA, Tokyo, 101-0062 (Japan)]. E-mail: inouen@riast.osakafu-u.ac.jp; Nakatsu, M. [RIAST, Osaka Prefecture University, Sakai, 599-8570 (Japan); Ono, H. [Japan Fine Ceramics Center, Tokyo, 105-0003 (Japan); Nitrogen Measurement WG, JEITA, Tokyo, 101-0062 (Japan)

    2006-04-01

    Local vibration mode (LVM) infrared absorption from shallow thermal donors (STD) composed of nitrogen-oxygen complexes in nitrogen-doped CZ silicon crystals was examined. The samples whose STD concentration had been determined were measured. The sample dependence of the peaks at 810 and 1018cm{sup -1} was similar to that of STD but the estimated concentration was slightly higher. New LVM peaks were found at 855, 973, 982, 1002cm{sup -1} and so on. Their magnitude and sample dependence agreed well with those of STD. Annealing temperature dependence of other samples supported the results. Annealing time dependence of STD concentration at 650 deg. C was examined. STD peaks at 250, 242 and those at 240, 234 and 238cm{sup -1} behaved differently, suggesting the presence of two kinds of STD origin.

  11. Multiscale studies on the nonlinear vibration of delaminated composite laminates–global vibration mode with micro buckles on the interfaces

    National Research Council Canada - National Science Library

    Jianghong Xue; Fei Xia; Jun Ye; Jianwen Zhang; Shuhua Chen; Ying Xiong; Zuyuan Tan; Renhuai Liu; Hong Yuan

    2017-01-01

    This paper presents a multiscale approach to study the nonlinear vibration of fiber reinforced composite laminates containing an embedded, through-width delamination dividing the laminate into four sub-laminates...

  12. Formation of aerial standing wave field using ultrasonic sources consisting of multiple stripe-mode transverse vibrating plates

    Science.gov (United States)

    Naito, Koki; Asami, Takuya; Miura, Hikaru

    2015-07-01

    Intense aerial acoustic waves can be produced by an ultrasonic source consisting of a transverse vibrating plate and an external jutting driving point. Previously, we studied the dimensional parameters of vibrating plates to produce stripe-mode patterns and thereby determine the plate dimensions that generate high-quality patterns. In this research, we use four transverse vibrating plates as ultrasonic sources to produce intense standing wave fields in air. As a result, an aerial standing wave field was formed in the field surrounded by four vibrating plates. Furthermore, for a total input power of 30 W for the two ultrasonic sources, a very strong (sound pressure level, 167 dB) wave field is obtained.

  13. Modeling the Vibrational Dynamics and Nonlinear Infrared Spectra of Coupled Amide I and II Modes in Peptides

    NARCIS (Netherlands)

    Dijkstra, Arend G.; Jansen, Thomas la Cour; Knoester, Jasper

    2011-01-01

    The amide vibrational modes play an important role in energy transport and relaxation in polypeptides and proteins and provide us with spectral markers for structure and structural dynamics of these macromolecules. Here, we present a detailed model to describe the dynamic properties of the amide I

  14. Stretching dependence of the vibration modes of a single-molecule Pt-H-2-Pt bridge

    DEFF Research Database (Denmark)

    Djukic, D.; Thygesen, Kristian Sommer; Untiedt, C.

    2005-01-01

    A conducting bridge of a single hydrogen molecule between Pt electrodes is formed in a break junction experiment. It has a conductance near the quantum unit, G(0)=2e(2)/h, carried by a single channel. Using point-contact spectroscopy three vibration modes are observed and their variation upon...

  15. VCD Robustness of the Amide-I and Amide-II Vibrational Modes of Small Peptide Models.

    Science.gov (United States)

    Góbi, Sándor; Magyarfalvi, Gábor; Tarczay, György

    2015-09-01

    The rotational strengths and the robustness values of amide-I and amide-II vibrational modes of For(AA)n NHMe (where AA is Val, Asn, Asp, or Cys, n = 1-5 for Val and Asn; n = 1 for Asp and Cys) model peptides with α-helix and β-sheet backbone conformations were computed by density functional methods. The robustness results verify empirical rules drawn from experiments and from computed rotational strengths linking amide-I and amide-II patterns in the vibrational circular dichroism (VCD) spectra of peptides with their backbone structures. For peptides with at least three residues (n ≥ 3) these characteristic patterns from coupled amide vibrational modes have robust signatures. For shorter peptide models many vibrational modes are nonrobust, and the robust modes can be dependent on the residues or on their side chain conformations in addition to backbone conformations. These robust VCD bands, however, provide information for the detailed structural analysis of these smaller systems. © 2015 Wiley Periodicals, Inc.

  16. Evolution of microstructure and residual stress under various vibration modes in 304 stainless steel welds.

    Science.gov (United States)

    Hsieh, Chih-Chun; Wang, Peng-Shuen; Wang, Jia-Siang; Wu, Weite

    2014-01-01

    Simultaneous vibration welding of 304 stainless steel was carried out with an eccentric circulating vibrator and a magnetic telescopic vibrator at subresonant (362 Hz and 59.3 Hz) and resonant (376 Hz and 60.9 Hz) frequencies. The experimental results indicate that the temperature gradient can be increased, accelerating nucleation and causing grain refinement during this process. During simultaneous vibration welding primary δ -ferrite can be refined and the morphologies of retained δ-ferrite become discontinuous so that δ-ferrite contents decrease. The smallest content of δ-ferrite (5.5%) occurred using the eccentric circulating vibrator. The diffraction intensities decreased and the FWHM widened with both vibration and no vibration. A residual stress can obviously be increased, producing an excellent effect on stress relief at a resonant frequency. The stress relief effect with an eccentric circulating vibrator was better than that obtained using a magnetic telescopic vibrator.

  17. Vibrational Surface Electron-Energy-Loss Spectroscopy Probes Confined Surface-Phonon Modes

    Directory of Open Access Journals (Sweden)

    Hugo Lourenço-Martins

    2017-12-01

    Full Text Available Recently, two reports [Krivanek et al. Nature (London 514, 209 (2014NATUAS0028-083610.1038/nature13870, Lagos et al. Nature (London 543, 529 (2017NATUAS0028-083610.1038/nature21699] have demonstrated the amazing possibility to probe vibrational excitations from nanoparticles with a spatial resolution much smaller than the corresponding free-space phonon wavelength using electron-energy-loss spectroscopy (EELS. While Lagos et al. evidenced a strong spatial and spectral modulation of the EELS signal over a nanoparticle, Krivanek et al. did not. Here, we show that discrepancies among different EELS experiments as well as their relation to optical near- and far-field optical experiments [Dai et al. Science 343, 1125 (2014SCIEAS0036-807510.1126/science.1246833] can be understood by introducing the concept of confined bright and dark surface phonon modes, whose density of states is probed by EELS. Such a concise formalism is the vibrational counterpart of the broadly used formalism for localized surface plasmons [Ouyang and Isaacson Philos. Mag. B 60, 481 (1989PMABDJ1364-281210.1080/13642818908205921, García de Abajo and Aizpurua Phys. Rev. B 56, 15873 (1997PRBMDO0163-182910.1103/PhysRevB.56.15873, García de Abajo and Kociak Phys. Rev. Lett. 100, 106804 (2008PRLTAO0031-900710.1103/PhysRevLett.100.106804, Boudarham and Kociak Phys. Rev. B 85, 245447 (2012PRBMDO1098-012110.1103/PhysRevB.85.245447]; it makes it straightforward to predict or interpret phenomena already known for localized surface plasmons such as environment-related energy shifts or the possibility of 3D mapping of the related surface charge densities [Collins et al. ACS Photonics 2, 1628 (2015APCHD52330-402210.1021/acsphotonics.5b00421].

  18. Component mode synthesis and large deflection vibration of complex structures. Volume 2: Single-mode large deflection vibrations of beams and plates using finite element method

    Science.gov (United States)

    Mei, Chuh

    1987-01-01

    A finite element method is presented for the large amplitude vibrations of complex structures that can be modelled with beam and rectangular plate elements subjected to harmonic excitation. Both inplane deformation and inertia are considered in the formulation. Derivation of the harmonic force and nonlinear stiffness matrices for a beam and a rectangular plate element are presented. Solution procedures and convergence characteristics of the finite element method are described. Nonlinear response to uniform and concentrated harmonic loadings and improved nonlinear free vibration results are presented for beams and rectangular plates of various boundary conditions.

  19. USE OF WHOLE-BODY VIBRATION AS A MODE OF WARMING UP BEFORE COUNTER MOVEMENT JUMP

    Directory of Open Access Journals (Sweden)

    Enrique G. Artero

    2007-12-01

    Full Text Available Whole-body vibration (WBV has been suggested to be particularly effective on the stretch-shortening cycle-based movements, such as the counter movement jump (CMJ test (Issurin, 2005. Nevertheless, the literature on short-term vibration exposure and lower limb explosive performance (measured by CMJ test is contradictory. Either transient improvements (Bosco et al., 2000; Cochrane and Stannard, 2005; Torvinen et al., 2002a or no effects (Torvinen et al., 2002b; Rittweger et al., 2003; Cormie et al., 2006 have been reported after a single WBV exposure ranging from 30 s to 10 min. The present study aimed at better characterizing the use of a single short bout of WBV as a mode of warming up before a CMJ test.A total of 114 university students (37 men, 77 women, aged 19.6 ± 2.0 years signed an informed consent form and volunteered to participate in the study. The study protocol was approved by the Review Committee for Research Involving Human Subjects of our center. Participants were asked to come to the laboratory in three occasions three days apart. First visit: familiarization session aiming to learn the CMJ technique and to experience the vibration stimulus. Second visit: the participants performed three consecutive CMJ with one min rest interval. No significant differences were observed among the jumps, and the highest score was retained. Third visit: the participants were exposed to a single short bout of WBV and immediately after they performed three CMJ with one min rest interval.An infrared contact timing platform (ERGO JUMP Plus - BOSCO SYSTEM, Byomedic, S.C.P., Barcelona, Spain was used to measure "flight" time (t during the vertical jump (accuracy 0.001 s. Maximum height achieved by the body centre of gravity (h was then estimated, i.e. h = g · t2 / 8, where g = 9.81 m/s2. In all occasions, the participants were instructed to abstain from strenuous exercise for the preceding 24 hours.Whole-body vibration was carried out on an oscillating

  20. Investigation of Heat Transfer and Magnetohydrodynamic Flow in Electroslag Remelting Furnace Using Vibrating Electrode

    Science.gov (United States)

    Wang, Fang; Wang, Qiang; Lou, Yanchun; Chen, Rui; Song, Zhaowei; Li, Baokuan

    2016-01-01

    A transient three-dimensional (3D) coupled mathematical model has been developed to understand the effect of a vibrating electrode on the electromagnetic, two-phase flow and temperature fields as well as the solidification in the electroslag remelting (ESR) process. With the magnetohydrodynamic model, the Joule heating and Lorentz force, which are the source terms in the energy and momentum equations, are recalculated at each iteration as a function of the phase distribution. The influence of the vibrating electrode on the formation of the metal droplet is demonstrated by the volume of fluid approach. Additionally, the solidification of the metal is modeled by an enthalpy-based technique, in which the mushy zone is treated as a porous medium with porosity equal to the liquid fraction. The present work is the first attempt to investigate the innovative technology of the ESR process with a vibrating electrode by a transient 3D comprehensive model. A reasonable agreement between the experiment and simulation is obtained. The results indicate that the whole process is presented as a periodic activity. When the metal droplets fall from the tip of the electrode, the horizontal component of velocity will generate electrode vibration. This will lead to the distribution variation of the flow field in the slag layer. The variation of temperature distribution occurs regularly and is periodically accompanied by the behavior of the falling metal droplets. With the decreasing vibrating frequency and amplitude, the relative velocity of the electrode and molten slag increase accordingly. The diameter of the molten droplets, the maximum temperature and the depth of the molten pool gradually become smaller, lower and shallower.

  1. Molecular dynamics simulations and instantaneous normal-mode analysis of the vibrational relaxation of the C-H stretching modes of N-methylacetamide-d in liquid deuterated water.

    Science.gov (United States)

    Bastida, Adolfo; Soler, Miguel A; Zúñiga, José; Requena, Alberto; Kalstein, Adrián; Fernández-Alberti, Sebastian

    2010-11-04

    Nonequilibrium molecular dynamics (MD) simulations and instantaneous normal mode (INMs) analyses are used to study the vibrational relaxation of the C-H stretching modes (ν(s)(CH₃)) of deuterated N-methylacetamide (NMAD) in aqueous (D2O) solution. The INMs are identified unequivocally in terms of the equilibrium normal modes (ENMs), or groups of them, using a restricted version of the recently proposed Min-Cost assignment method. After excitation of the parent ν(s)(CH₃) modes with one vibrational quantum, the vibrational energy is shown to dissipate through both intramolecular vibrational redistribution (IVR) and intermolecular vibrational energy transfer (VET). The decay of the vibrational energy of the ν(s)(CH₃) modes is well fitted to a triple exponential function, with each characterizing a well-defined stage of the entire relaxation process. The first, and major, relaxation stage corresponds to a coherent ultrashort (τ(rel) = 0.07 ps) energy transfer from the parent ν(s)(CH₃) modes to the methyl bending modes δ(CH₃), so that the initially excited state rapidly evolves into a mixed stretch-bend state. In the second stage, characterized by a time of 0.92 ps, the vibrational energy flows through IVR to a number of mid-range-energy vibrations of the solute. In the third stage, the vibrational energy accumulated in the excited modes dissipates into the bath through an indirect VET process mediated by lower-energy modes, on a time scale of 10.6 ps. All the specific relaxation channels participating in the whole relaxation process are properly identified. The results from the simulations are finally compared with the recent experimental measurements of the ν(s)(CH₃) vibrational energy relaxation in NMAD/D₂O(l) reported by Dlott et al. (J. Phys. Chem. A 2009, 113, 75.) using ultrafast infrared-Raman spectroscopy.

  2. Localised vibrational mode spectroscopy studies of self-interstitial clusters in neutron irradiated silicon

    Energy Technology Data Exchange (ETDEWEB)

    Londos, C. A.; Antonaras, G. [University of Athens, Solid State Physics Section, Panepistimiopolis Zografos, Athens 157 84 (Greece); Chroneos, A. [Materials Engineering, The Open University, Milton Keynes MK7 6AA (United Kingdom); Department of Materials, Imperial College, London SW7 2AZ (United Kingdom)

    2013-07-28

    The evolution of self-interstitial clusters in silicon (Si), produced by fast neutron irradiation of silicon crystals followed by anneals up to 750 °C, is investigated using localised vibrational mode spectroscopy. A band at 582 cm{sup −1} appears after irradiation and is stable up to 550 °C was attributed to small self-interstitial clusters (I{sub n}, n ≤ 4), with the most probable candidate the I{sub 4} structure. Two bands at 713 and 758 cm{sup −1} arising in the spectra upon annealing of the 582 cm{sup −1} band and surviving up to ∼750 °C were correlated with larger interstitial clusters (I{sub n}, 5 ≤ n ≤ 8), with the most probable candidate the I{sub 8} structure or/and with chainlike defects which are precursors of the (311) extended defects. The results illustrate the presence of different interstitial clusters I{sub n}, at the various temperature intervals of the material, in the course of an isochronal anneal sequence. As the annealing temperature increases, they evolve from first-order structures with a small number of self-interstitials (I{sub n}, n ≤ 4) for the temperatures 50 < T < 550 °C, to second order structures (I{sub n}, 5 ≤ n ≤ 8) with a larger number of interstitials, for the temperatures 550 < T < 750 °C.

  3. Local vibration modes and nitrogen incorporation in AlGaAs:N layers

    Energy Technology Data Exchange (ETDEWEB)

    Gallardo, E.; Lazic, S.; Calleja, J.M. [Dept. de Fisica de Materiales, Universidad Autonoma de Madrid (Spain); Miguel-Sanchez, J.; Montes, M.; Hierro, A.; Gargallo-Caballero, R.; Guzman, A.; Munoz, E. [Instituto de Sistemas Optoelectronicos y Microtecnologia, Universidad Politecnica de Madrid (Spain); Teweldeberhan, A.M.; Fahy, S. [Tyndall National Institute, Cork (Ireland)

    2008-07-01

    Raman scattering measurements in dilute AlGaAs:N films grown by plasma-assisted molecular beam epitaxy on (100) GaAs substrates reveal strong local vibration modes (LVM) associated to N complexes. The LVM observed frequencies between 325 and 540 cm{sup -1} are in good agreement with density functional theory supercell calculations of Al{sub n}Ga{sub 4-n}N complexes (n=1,2,3,4). We find that the observed LVMs correspond to all n values including Al{sub 4}N. The LVMs spectra are resonant at energies around 1.85 eV. The values of the extended phonon frequencies of the ternary compound (GaAs and AlAs-like) reveal changes in the N distribution depending on the growth conditions: A transition from random- to non-random nitrogen distribution is observed upon increasing the growth temperature. Our results confirm the preferential bonding of N to Al in AlGaAs:N, due to the higher Al-N bond strength as compared to the Ga-N bond. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  4. On the correlation between phase-locking modes and Vibrational Resonance in a neuronal model

    Science.gov (United States)

    Morfu, S.; Bordet, M.

    2018-02-01

    We numerically and experimentally investigate the underlying mechanism leading to multiple resonances in the FitzHugh-Nagumo model driven by a bichromatic excitation. Using a FitzHugh-Nagumo circuit, we first analyze the number of spikes triggered by the system in response to a single sinusoidal wave forcing. We build an encoding diagram where different phase-locking modes are identified according to the amplitude and frequency of the sinusoidal excitation. Next, we consider the bichromatic driving which consists in a low frequency sinusoidal wave perturbed by an additive high frequency signal. Beside the classical Vibrational Resonance phenomenon, we show in real experiments that multiple resonances can be reached by an appropriate setting of the perturbation parameters. We clearly establish a correlation between these resonances and the encoding diagram of the low frequency signal free FitzHugh-Nagumo model. We show with realistic parameters that sharp transitions of the encoding diagram allow to predict the main resonances. Our experiments are confirmed by numerical simulations of the system response.

  5. Thermal performance of shallow solar pond under open cycle continuous flow heating mode for heat extraction

    Energy Technology Data Exchange (ETDEWEB)

    El-Sebaii, A.A. [Department of Physics, Faculty of Science, Tanta University, Tanta 31527 (Egypt)]. E-mail: aasebaii@yahoo.com; Aboul-Enein, S. [Department of Physics, Faculty of Science, Tanta University, Tanta 31527 (Egypt); Ramadan, M.R.I. [Department of Physics, Faculty of Science, Tanta University, Tanta 31527 (Egypt); Khallaf, A.M. [Department of Physics, Faculty of Science, Tanta University, Tanta 31527 (Egypt)

    2006-05-15

    The thermal performance of a shallow solar pond (SSP) under an open cycle continuous flow heating mode for heat extraction has been investigated. A serpentine heat exchanger (HE), either welded to the absorber plate or immersed in the pond water, has been used for extracting the heat. Suitable computer programs have been developed based on analytical solutions of the energy balance equations for the various elements of the SSP in the presence of the HE. Numerical calculations have been performed to study the effect of different operational and configurational parameters on the pond performance. In order to improve the pond performance, optimization of the various dimensions of the pond with the HE has been performed. The effects of the design parameters of the HE's tube, i.e. length L{sub he}, diameter D and mass flow rate m-bar {sub f} of the fluid flowing through the HE, on the pond performance have been investigated. The outlet temperature of the HE's fluid T{sub fo} is found to increase with increase of the HE length L{sub he}, and it decreases with increase of the mass flow rate of the HE's fluid m-bar {sub f} up to typical values for these parameters. Typical values for L{sub he} and m-bar {sub f} are found to be 4m and 0.004kg/s beyond which the change in T{sub fo} becomes insignificant. Experiments have been performed for the pond under different operational conditions with a HE welded to the absorber plate. To validate the proposed mathematical models, comparisons between experimental and theoretical results have been performed. Good agreement has been achieved.

  6. The Vibration Analysis of Tube Bundles Induced by Fluid Elastic Excitation in Shell Side of Heat Exchanger

    Science.gov (United States)

    Bao, Minle; Wang, Lu; Li, Wenyao; Gao, Tianze

    2017-09-01

    Fluid elastic excitation in shell side of heat exchanger was deduced theoretically in this paper. Model foundation was completed by using Pro / Engineer software. The finite element model was constructed and imported into the FLUENT module. The flow field simulation adopted the dynamic mesh model, RNG k-ε model and no-slip boundary conditions. Analysing different positions vibration of tube bundles by selecting three regions in shell side of heat exchanger. The results show that heat exchanger tube bundles at the inlet of the shell side are more likely to be failure due to fluid induced vibration.

  7. Research on Effective Electric-Mechanical Coupling Coefficient of Sandwich Type Piezoelectric Ultrasonic Transducer Using Bending Vibration Mode

    Directory of Open Access Journals (Sweden)

    Qiang Zhang

    2015-01-01

    Full Text Available An analytical model on electromechanical coupling coefficient and the length optimization of a bending piezoelectric ultrasonic transducer are proposed. The piezoelectric transducer consists of 8 PZT elements sandwiched between four thin electrodes, and the PZT elements are clamped by a screwed connection between fore beam and back beam. Firstly, bending vibration model of the piezoelectric transducer is built based on the Timoshenko beam theory. Secondly, the analytical model of effective electromechanical coupling coefficient is built based on the bending vibration model. Energy method and electromechanical equivalent circuit method are involved in the modelling process. To validate the analytical model, sandwich type piezoelectric transducer example in second order bending vibration mode is analysed. Effective electromechanical coupling coefficient of the transducer is optimized with simplex reflection technique, and the optimized ratio of length of the transducers is obtained. Finally, experimental prototypes of the sandwich type piezoelectric transducers are fabricated. Bending vibration mode and impedance of the experimental prototypes are tested, and electromechanical coupling coefficient is obtained according to the testing results. Results show that the analytical model is in good agreement with the experimental model.

  8. Segmentation of a Vibro-Shock Cantilever-Type Piezoelectric Energy Harvester Operating in Higher Transverse Vibration Modes

    Directory of Open Access Journals (Sweden)

    Darius Zizys

    2015-12-01

    Full Text Available The piezoelectric transduction mechanism is a common vibration-to-electric energy harvesting approach. Piezoelectric energy harvesters are typically mounted on a vibrating host structure, whereby alternating voltage output is generated by a dynamic strain field. A design target in this case is to match the natural frequency of the harvester to the ambient excitation frequency for the device to operate in resonance mode, thus significantly increasing vibration amplitudes and, as a result, energy output. Other fundamental vibration modes have strain nodes, where the dynamic strain field changes sign in the direction of the cantilever length. The paper reports on a dimensionless numerical transient analysis of a cantilever of a constant cross-section and an optimally-shaped cantilever with the objective to accurately predict the position of a strain node. Total effective strain produced by both cantilevers segmented at the strain node is calculated via transient analysis and compared to the strain output produced by the cantilevers segmented at strain nodes obtained from modal analysis, demonstrating a 7% increase in energy output. Theoretical results were experimentally verified by using open-circuit voltage values measured for the cantilevers segmented at optimal and suboptimal segmentation lines.

  9. Segmentation of a Vibro-Shock Cantilever-Type Piezoelectric Energy Harvester Operating in Higher Transverse Vibration Modes.

    Science.gov (United States)

    Zizys, Darius; Gaidys, Rimvydas; Dauksevicius, Rolanas; Ostasevicius, Vytautas; Daniulaitis, Vytautas

    2015-12-23

    The piezoelectric transduction mechanism is a common vibration-to-electric energy harvesting approach. Piezoelectric energy harvesters are typically mounted on a vibrating host structure, whereby alternating voltage output is generated by a dynamic strain field. A design target in this case is to match the natural frequency of the harvester to the ambient excitation frequency for the device to operate in resonance mode, thus significantly increasing vibration amplitudes and, as a result, energy output. Other fundamental vibration modes have strain nodes, where the dynamic strain field changes sign in the direction of the cantilever length. The paper reports on a dimensionless numerical transient analysis of a cantilever of a constant cross-section and an optimally-shaped cantilever with the objective to accurately predict the position of a strain node. Total effective strain produced by both cantilevers segmented at the strain node is calculated via transient analysis and compared to the strain output produced by the cantilevers segmented at strain nodes obtained from modal analysis, demonstrating a 7% increase in energy output. Theoretical results were experimentally verified by using open-circuit voltage values measured for the cantilevers segmented at optimal and suboptimal segmentation lines.

  10. A novel scheme for the discrete prediction of high-frequency vibration response: Discrete singular convolution-mode superposition approach

    Science.gov (United States)

    Seçgin, Abdullah; Saide Sarıgül, A.

    2009-03-01

    This study introduces a novel scheme for the discrete high-frequency forced vibration analysis based on discrete singular convolution (DSC) and mode superposition (MS) approaches. The accuracy of the DSC-MS is validated for thin beams and plates by comparing with available analytical solutions. The performance of the DSC-MS is evaluated by predicting spatial distribution and discrete frequency spectra of the vibration response of thin plates with two different boundary conditions. The frequency spectra of the time-harmonic excitation forces are in the form of ideal and band-limited white noise so that the natural modes in the frequency band are provoked. The solution exposes high-frequency response behaviour definitely. Therefore, it is hoped with this paper to contribute the studies on the treatment of uncertainties in the high-frequency design applications.

  11. Direct assignment of molecular vibrations via normal mode analysis of the neutron dynamic pair distribution function technique.

    Science.gov (United States)

    Fry-Petit, A M; Rebola, A F; Mourigal, M; Valentine, M; Drichko, N; Sheckelton, J P; Fennie, C J; McQueen, T M

    2015-09-28

    For over a century, vibrational spectroscopy has enhanced the study of materials. Yet, assignment of particular molecular motions to vibrational excitations has relied on indirect methods. Here, we demonstrate that applying group theoretical methods to the dynamic pair distribution function analysis of neutron scattering data provides direct access to the individual atomic displacements responsible for these excitations. Applied to the molecule-based frustrated magnet with a potential magnetic valence-bond state, LiZn2Mo3O8, this approach allows direct assignment of the constrained rotational mode of Mo3O13 clusters and internal modes of MoO6 polyhedra. We anticipate that coupling this well known data analysis technique with dynamic pair distribution function analysis will have broad application in connecting structural dynamics to physical properties in a wide range of molecular and solid state systems.

  12. Effect of surface related organic vibrational modes in luminescent upconversion dynamics of rare earth ions doped nanoparticles.

    Science.gov (United States)

    Wang, Yu; Smolarek, Szymon; Kong, Xianggui; Buma, Wybren Jan; Brouwer, Albert Manfred; Zhang, Hong

    2010-11-01

    Physical and chemical properties of nanoparticles are known to be subject to the surface factors. For their biological/biomedical applications, typically, surface of the nanoparticles has to be modified which inevitably affects their performance. In this work we have studied the interaction between the surface related organic vibrational modes and the luminescent centers--rare earth ions--in one of the most efficient luminescence upconversion nanosystems--NaYF4. Specifically, the surface quenching centers, the surface related luminescent centers, as well as the role of shell properties, are investigated spectroscopically. Our results demonstrate that the surface related high-frequency vibrational modes can be critical to the spectral properties of the nanosystems once the surface is not well separated from the discrete luminescent centers.

  13. Vibration-Assisted Laser Surface Texturing and Electromachining for the Intensification of Boiling Heat Transfer in a Minichannel

    Directory of Open Access Journals (Sweden)

    Piasecka M.

    2017-12-01

    Full Text Available The paper describes applications of the vibration-assisted laser surface texturing and spark erosion process as methods of modifying properties and structures of metal surfaces. Practical aspects of the use of produced surfaces in the heat exchanger with a minichannel have been described. Compared with smooth surfaces, developed metal surfaces obtained by vibration-assisted laser surface texturing and electromachining show more effective heat transfer. The local heat transfer coefficient for the saturated boiling region obtained for developed surfaces had the values significantly higher than those obtained for the smooth plate at the same heat flux. The experimental results are presented as the heated plate temperature (obtained from infrared thermography and relationships between the heat transfer coefficient and the distance along the length of the minichannel for the saturated boiling region.

  14. Selective self-excitation of higher vibrational modes of graphene nano-ribbons and carbon nanotubes through magnetomotive instability

    OpenAIRE

    Nordenfelt, Anders

    2011-01-01

    We demonstrate theoretically the feasibility of selective self-excitation of higher-mode flexural vibrations of graphene nano-ribbons and carbon nanotubes by the means of magnetomotive instability. Apart from the mechanical resonator, the device consists only of a constant voltage source, an inductor, a capacitor, a gate electrode and a constant magnetic field. Numerical simluations were performed on both graphene and carbon nanotubes displaying an overall similar behaviour, but with some dif...

  15. Abstract: Stoichiometry, Vibrational Modes and Structures of Molten Nb2O5-K2S2O7 Mixtures

    DEFF Research Database (Denmark)

    Boghosian, S.; Borup, F.; Berg, Rolf W.

    1998-01-01

    High temperature Raman spectroscopy is used tostudy the vibrational modes and structures of the Nb205-K2S207(0 stoichiometry are performed...... in order to characterise the complex(es) formed. The determination of stoichiometry is done following a general procedure which is based on a simple formalism correlating measurements of relative Raman band intensities with the stoichiometry of solutes in molten salt solvents....

  16. Layer-number dependent high-frequency vibration modes in few-layer transition metal dichalcogenides induced by interlayer couplings

    Science.gov (United States)

    Tan, Qing-Hai; Zhang, Xin; Luo, Xiang-Dong; Zhang, Jun; Tan, Ping-Heng

    2017-03-01

    Two-dimensional transition metal dichalcogenides (TMDs) have attracted extensive attention due to their many novel properties. The atoms within each layer in two-dimensional TMDs are joined together by covalent bonds, while van der Waals interactions combine the layers together. This makes its lattice dynamics layer-number dependent. The evolutions of ultralow frequency ( 50 cm-1) vibration modes in few-layer TMDs and demonstrate how the interlayer coupling leads to the splitting of high-frequency vibration modes, known as Davydov splitting. Such Davydov splitting can be well described by a van der Waals model, which directly links the splitting with the interlayer coupling. Our review expands the understanding on the effect of interlayer coupling on the high-frequency vibration modes in TMDs and other two-dimensional materials. Project supported by the National Basic Research Program of China (No. 2016YFA0301200), the National Natural Science Foundation of China (Nos. 11225421, 11474277, 11434010, 61474067, 11604326, 11574305 and 51527901), and the National Young 1000 Talent Plan of China.

  17. Radiative heat transfer in low-dimensional systems -- microscopic mode

    Science.gov (United States)

    Woods, Lilia; Phan, Anh; Drosdoff, David

    2013-03-01

    Radiative heat transfer between objects can increase dramatically at sub-wavelength scales. Exploring ways to modulate such transport between nano-systems is a key issue from fundamental and applied points of view. We advance the theoretical understanding of radiative heat transfer between nano-objects by introducing a microscopic model, which takes into account the individual atoms and their atomic polarizabilities. This approach is especially useful to investigate nano-objects with various geometries and give a detailed description of the heat transfer distribution. We employ this model to study the heat exchange in graphene nanoribbon/substrate systems. Our results for the distance separations, substrates, and presence of extended or localized defects enable making predictions for tailoring the radiative heat transfer at the nanoscale. Financial support from the Department of Energy under Contract No. DE-FG02-06ER46297 is acknowledged.

  18. Pulsatile flow of blood and heat transfer with variable viscosity under magnetic and vibration environment

    Energy Technology Data Exchange (ETDEWEB)

    Shit, G.C., E-mail: gopal_iitkgp@yahoo.co.in; Majee, Sreeparna

    2015-08-15

    Unsteady flow of blood and heat transfer characteristics in the neighborhood of an overlapping constricted artery have been investigated in the presence of magnetic field and whole body vibration. The laminar flow of blood is taken to be incompressible and Newtonian fluid with variable viscosity depending upon temperature with an aim to provide resemblance to the real situation in the physiological system. The unsteady flow mechanism in the constricted artery is subjected to a pulsatile pressure gradient arising from systematic functioning of the heart and from the periodic body acceleration. The numerical computation has been performed using finite difference method by developing Crank–Nicolson scheme. The results show that the volumetric flow rate, skin-friction and the rate of heat transfer at the wall are significantly altered in the downstream of the constricted region. The axial velocity profile, temperature and flow rate increases with increase in temperature dependent viscosity, while the opposite trend is observed in the case of skin-friction and flow impedance. - Highlights: • We have investigated the pulsatile MHD flow of blood and heat transfer in arteries. • The influence of periodic body acceleration has been taken into account. • The temperature dependent viscosity of blood is considered. • The variable viscosity has an increasing effect on blood flow and heat transfer. • The overall temperature distribution enhances in the presence of magnetic field.

  19. In Vitro Comparison of a Vibrating Mesh Nebulizer Operating in Inspiratory Synchronized and Continuous Nebulization Modes During Noninvasive Ventilation.

    Science.gov (United States)

    Michotte, Jean-Bernard; Staderini, Enrico; Le Pennec, Deborah; Dugernier, Jonathan; Rusu, Rares; Roeseler, Jean; Vecellio, Laurent; Liistro, Giuseppe; Reychler, Grégory

    2016-08-01

    Backround: Coupling nebulization with noninvasive ventilation (NIV) has been shown to be effective in patients with respiratory diseases. However, a breath-synchronized nebulization option that could potentially improve drug delivery by limiting drug loss during exhalation is currently not available on bilevel ventilators. The aim of this in vitro study was to compare aerosol delivery of amikacin with a vibrating mesh nebulizer coupled to a single-limb circuit bilevel ventilator, using conventional continuous (Conti-Neb) and experimental inspiratory synchronized (Inspi-Neb) nebulization modes. Using an adult lung bench model of NIV, we tested a vibrating mesh device coupled with a bilevel ventilator in both nebulization modes. Inspi-Neb delivered aerosol only during the whole inspiratory phase, whereas Conti-Neb delivered aerosol continuously. The nebulizer was charged with amikacin solution (250 mg/3 mL) and placed at two different positions: between the lung and exhalation port and between the ventilator and exhalation port. Inhaled, expiratory wasted and circuit lost doses were assessed by residual gravimetric method. Particle size distribution of aerosol delivered at the outlet of the ventilator circuit during both nebulization modes was measured by laser diffraction method. Regardless of the nebulizer position, Inspi-Neb produced higher inhaled dose (p lung and exhalation port (48.7% ± 0.3% of the nominal dose). During simulated NIV with a single-limb circuit bilevel ventilator, the use of inspiratory synchronized vibrating mesh nebulization improves respirable dose and reduces drug loss of amikacin compared with continuous vibrating mesh nebulization.

  20. Development and applications of two computational procedures for determining the vibration modes of structural systems. [aircraft structures - aerospaceplanes

    Science.gov (United States)

    Kvaternik, R. G.

    1975-01-01

    Two computational procedures for analyzing complex structural systems for their natural modes and frequencies of vibration are presented. Both procedures are based on a substructures methodology and both employ the finite-element stiffness method to model the constituent substructures. The first procedure is a direct method based on solving the eigenvalue problem associated with a finite-element representation of the complete structure. The second procedure is a component-mode synthesis scheme in which the vibration modes of the complete structure are synthesized from modes of substructures into which the structure is divided. The analytical basis of the methods contains a combination of features which enhance the generality of the procedures. The computational procedures exhibit a unique utilitarian character with respect to the versatility, computational convenience, and ease of computer implementation. The computational procedures were implemented in two special-purpose computer programs. The results of the application of these programs to several structural configurations are shown and comparisons are made with experiment.

  1. Distinct Skeletal Muscle Gene Regulation from Active Contraction, Passive Vibration, and Whole Body Heat Stress in Humans.

    Directory of Open Access Journals (Sweden)

    Michael A Petrie

    Full Text Available Skeletal muscle exercise regulates several important metabolic genes in humans. We know little about the effects of environmental stress (heat and mechanical stress (vibration on skeletal muscle. Passive mechanical stress or systemic heat stress are often used in combination with many active exercise programs. We designed a method to deliver a vibration stress and systemic heat stress to compare the effects with active skeletal muscle contraction.The purpose of this study is to examine whether active mechanical stress (muscle contraction, passive mechanical stress (vibration, or systemic whole body heat stress regulates key gene signatures associated with muscle metabolism, hypertrophy/atrophy, and inflammation/repair.Eleven subjects, six able-bodied and five with chronic spinal cord injury (SCI participated in the study. The six able-bodied subjects sat in a heat stress chamber for 30 minutes. Five subjects with SCI received a single dose of limb-segment vibration or a dose of repetitive electrically induced muscle contractions. Three hours after the completion of each stress, we performed a muscle biopsy (vastus lateralis or soleus to analyze mRNA gene expression.We discovered repetitive active muscle contractions up regulated metabolic transcription factors NR4A3 (12.45 fold, PGC-1α (5.46 fold, and ABRA (5.98 fold; and repressed MSTN (0.56 fold. Heat stress repressed PGC-1α (0.74 fold change; p < 0.05; while vibration induced FOXK2 (2.36 fold change; p < 0.05. Vibration similarly caused a down regulation of MSTN (0.74 fold change; p < 0.05, but to a lesser extent than active muscle contraction. Vibration induced FOXK2 (p < 0.05 while heat stress repressed PGC-1α (0.74 fold and ANKRD1 genes (0.51 fold; p < 0.05.These findings support a distinct gene regulation in response to heat stress, vibration, and muscle contractions. Understanding these responses may assist in developing regenerative rehabilitation interventions to improve muscle cell

  2. Experimental and DFT dimer modeling studies of the H-bond induced-vibration modes of l-β-Homoserine.

    Science.gov (United States)

    Yalagi, Shashikala; Tonannavar, J; Yenagi, Jayashree

    2017-06-15

    The vibrational spectra for l-β-Homoserine have been measured (IR absorption: 4000-400cm(-1)/Raman spectra: 4000-200cm(-1)). Characteristic vibrational modes of ammonium (-NH3(+)), carboxylate (-CO2(-)) and hydroxyl (-OH) groups across the 3700-1400cm(-1) are all identified to have originated in inter-molecular hydrogen bonding involving these functional groups. DFT calculations at B3LYP/6-311++G(d, p) level have yielded a single neutral monomer in the gas phase. Since as a member of the amino acids which are known to possess zwitterionic structure in condensed phase, the neutral monomer of l-β-Homoserine is optimized to a zwitterionic structure in a water medium. Consideration of two dimer structures, one dimer with -NH‧‧‧O bond and another -OH‧‧‧O bond, has given rise to vibrational modes that satisfactorily fit to all the observed absorption and Raman bands. It is found that the dimer with -OH‧‧‧O bond (binding energy, 8.896kcal/mol) is more tightly bound than the dimer with -NH‧‧‧O bond (8.363kcal/mol). Copyright © 2017 Elsevier B.V. All rights reserved.

  3. A study of the flow boiling heat transfer in a minichannel for a heated wall with surface texture produced by vibration-assisted laser machining

    Science.gov (United States)

    Piasecka, Magdalena; Strąk, Kinga; Maciejewska, Beata; Grabas, Bogusław

    2016-09-01

    The paper presents results concerning flow boiling heat transfer in a vertical minichannel with a depth of 1.7 mm and a width of 16 mm. The element responsible for heating FC-72, which flowed laminarly in the minichannel, was a plate with an enhanced surface. Two types of surface textures were considered. Both were produced by vibration-assisted laser machining. Infrared thermography was used to record changes in the temperature on the outer smooth side of the plate. Two-phase flow patterns were observed through a glass pane. The main aim of the study was to analyze how the two types of surface textures affect the heat transfer coefficient. A two-dimensional heat transfer approach was proposed to determine the local values of the heat transfer coefficient. The inverse problem for the heated wall was solved using a semi-analytical method based on the Trefftz functions. The results are presented as relationships between the heat transfer coefficient and the distance along the minichannel length and as boiling curves. The experimental data obtained for the two types of enhanced heated surfaces was compared with the results recorded for the smooth heated surface. The highest local values of the heat transfer coefficient were reported in the saturated boiling region for the plate with the type 1 texture produced by vibration-assisted laser machining.

  4. Evidence for cooperative vibrational relaxation of the NH-, OH-, and OD-stretching modes in hydrogen-bonded liquids using infrared pump-probe spectroscopy.

    Science.gov (United States)

    Shaw, D J; Panman, M R; Woutersen, S

    2009-11-27

    Vibrational energy relaxation of the NH-, OH-, and OD-stretching modes in hydrogen-bonded liquids has been investigated by means of infrared pump-probe spectroscopy. The relaxation rates have been determined both in neat liquids and in isotopic mixtures with systematically varied isotope fractions. In all liquids, the vibrational relaxation rate increases as the isotope fraction is increased and reaches a maximum in the neat liquid. The dependence of the relaxation rate on the isotope fraction suggests a relaxation channel in which the vibrational energy is partitioned between accepting modes of two neighboring molecules.

  5. Influence of design and mode parameters on pump performance curve of heat generating aggregate

    Science.gov (United States)

    Barykin, O.; Kovalyov, S.; Ovcharenko, M.; Papchenko, A.

    2017-08-01

    Classification of multi-functional heat generating aggregates according to the function is considered in this article. Analysis of operating process mathematical model was implemented and methods for its refinement were proposed. Results of physical investigation of heat generating aggregate design and mode parameters influence on its power and head were presented.

  6. Controlling the heating mode of heat pumps with the TRIANA three step methodology

    NARCIS (Netherlands)

    Toersche, Hermen; Bakker, Vincent; Molderink, Albert; Nykamp, Stefan; Hurink, Johann L.; Smit, Gerardus Johannes Maria

    2012-01-01

    Heat pump based heating systems are increasingly becoming an economic and efficient alternative for domestic gas heating systems. Concentrations of heat pump installations do consume large amounts of electricity, causing significant grid distribution and stability issues when the diversity factor is

  7. Anomalous vibrational modes in few layer WTe2 revealed by polarized Raman scattering and first-principles calculations

    Science.gov (United States)

    Cao, Yan; Sheremetyeva, Natalya; Liang, Liangbo; Yuan, Hui; Zhong, Tingting; Meunier, Vincent; Pan, Minghu

    2017-09-01

    When layered transition-metal dichalcogenides (TMDs) are scaled down from a three- to a 2D geometry, electronic and structural transitions occur, leading to the emergence of properties not usually found in the bulk. Here, we report a systematic Raman study of exfoliated semi-metallic WTe2 flakes with thickness ranging from few layers down to a single layer. A dramatic change in the Raman spectra occurs between the monolayer and few-layer WTe2 as a vibrational mode centered at ~86.9 cm-1 in the monolayer splits into two active modes at 82.9 and 89.6 cm-1 in the bilayer. Davydov splitting of these two modes is found in the bilayer, as further evidenced by polarized Raman measurements. Strong angular dependence of Raman modes on the WTe2 film thickness reflects that the existence of directional interlayer interaction, rather than isotropic van der Waals (vdw) coupling, is playing an essential role affecting the phonon modes, especially in anisotropic 2D WTe2 material. Therefore, the strong evolution of Raman modes with thickness and polarization direction, can not only be a reliable fingerprint for the determination of the thickness and the crystallographic orientation, but can also be an ideal probe for such strong and directional interlayer interaction.

  8. Time-averaged phase-stepped ESPI with CO2 laser and shearography in the visible for identification of vibration mode shapes

    Science.gov (United States)

    Vandenrijt, Jean-François; Thizy, Cédric; Georges, Marc P.

    2015-08-01

    We present investigation of interferometric methods for vibration mode identification to be applied on shakers in industrial environment. We consider long wave infrared ESPI in time-averaged mode with the use of phase-stepping which allows transforming Bessel fringes, typical to the time averaging, into phase values which provide a better way for identification of vibration mode shapes. The use of long laser wavelength allows measuring larger amplitudes of vibrations compared to what is achieved in visible light. Also longer wavelengths allow lower sensitivity to external perturbations. Time-averaged phase-stepped shearography in visible is also used as a compared alternative to LWIR ESPI for working in industrial environments. Although not demonstrated here, an interesting feature for the future investigations on LWIR ESPI is its potentiality of simultaneous temperature measurement during vibrations.

  9. Noninvasive Vibrational Mode Spectroscopy of Ion Coulomb Crystals through Resonant Collective Coupling to an Optical Cavity Field

    DEFF Research Database (Denmark)

    Dantan, Aurélien; Marler, Joan; Albert, Magnus

    2010-01-01

    We report on a novel noninvasive method to determine the normal mode frequencies of ion Coulomb crystals in traps based on the resonance enhanced collective coupling between the electronic states of the ions and an optical cavity field at the single photon level. Excitations of the normal modes...... are observed through a Doppler broadening of the resonance. An excellent agreement with the predictions of a zero-temperature uniformly charged liquid plasma model is found. The technique opens up for investigations of the heating and damping of cold plasma modes, as well as the coupling between them....

  10. Aerodynamic heating in transitional hypersonic boundary layers: Role of second-mode instability

    Science.gov (United States)

    Zhu, Yiding; Chen, Xi; Wu, Jiezhi; Chen, Shiyi; Lee, Cunbiao; Gad-el-Hak, Mohamed

    2018-01-01

    The evolution of second-mode instabilities in hypersonic boundary layers and its effects on aerodynamic heating are investigated. Experiments are conducted in a Mach 6 wind tunnel using fast-response pressure sensors, fluorescent temperature-sensitive paint, and particle image velocimetry. Calculations based on parabolic stability equations and direct numerical simulations are also performed. It is found that second-mode waves, accompanied by high-frequency alternating fluid compression and expansion, produce intense aerodynamic heating in a small region that rapidly heats the fluid passing through it. As the second-mode waves decay downstream, the dilatation-induced aerodynamic heating decreases while its shear-induced counterpart keeps growing. The latter brings about a second growth of the surface temperature when transition is completed.

  11. Dynamics of coupled vibration modes in a quantum non-linear mechanical resonator

    NARCIS (Netherlands)

    Labadze, G.; Dukalski, M.S.; Blanter, Y.M.

    2016-01-01

    We investigate the behaviour of two non-linearly coupled flexural modes of a doubly clamped suspended beam (nanomechanical resonator). One of the modes is externally driven. We demonstrate that classically, the behavior of the non-driven mode is reminiscent of that of a parametrically driven

  12. Anomalous heat transfer modes of nanofluids: a review based on statistical analysis

    Science.gov (United States)

    2011-01-01

    This paper contains the results of a concise statistical review analysis of a large amount of publications regarding the anomalous heat transfer modes of nanofluids. The application of nanofluids as coolants is a novel practise with no established physical foundations explaining the observed anomalous heat transfer. As a consequence, traditional methods of performing a literature review may not be adequate in presenting objectively the results representing the bulk of the available literature. The current literature review analysis aims to resolve the problems faced by researchers in the past by employing an unbiased statistical analysis to present and reveal the current trends and general belief of the scientific community regarding the anomalous heat transfer modes of nanofluids. The thermal performance analysis indicated that statistically there exists a variable enhancement for conduction, convection/mixed heat transfer, pool boiling heat transfer and critical heat flux modes. The most popular proposed mechanisms in the literature to explain heat transfer in nanofluids are revealed, as well as possible trends between nanofluid properties and thermal performance. The review also suggests future experimentation to provide more conclusive answers to the control mechanisms and influential parameters of heat transfer in nanofluids. PMID:21711932

  13. Anomalous heat transfer modes of nanofluids: a review based on statistical analysis

    Science.gov (United States)

    Sergis, Antonis; Hardalupas, Yannis

    2011-05-01

    This paper contains the results of a concise statistical review analysis of a large amount of publications regarding the anomalous heat transfer modes of nanofluids. The application of nanofluids as coolants is a novel practise with no established physical foundations explaining the observed anomalous heat transfer. As a consequence, traditional methods of performing a literature review may not be adequate in presenting objectively the results representing the bulk of the available literature. The current literature review analysis aims to resolve the problems faced by researchers in the past by employing an unbiased statistical analysis to present and reveal the current trends and general belief of the scientific community regarding the anomalous heat transfer modes of nanofluids. The thermal performance analysis indicated that statistically there exists a variable enhancement for conduction, convection/mixed heat transfer, pool boiling heat transfer and critical heat flux modes. The most popular proposed mechanisms in the literature to explain heat transfer in nanofluids are revealed, as well as possible trends between nanofluid properties and thermal performance. The review also suggests future experimentation to provide more conclusive answers to the control mechanisms and influential parameters of heat transfer in nanofluids.

  14. Anomalous heat transfer modes of nanofluids: a review based on statistical analysis

    Directory of Open Access Journals (Sweden)

    Sergis Antonis

    2011-01-01

    Full Text Available Abstract This paper contains the results of a concise statistical review analysis of a large amount of publications regarding the anomalous heat transfer modes of nanofluids. The application of nanofluids as coolants is a novel practise with no established physical foundations explaining the observed anomalous heat transfer. As a consequence, traditional methods of performing a literature review may not be adequate in presenting objectively the results representing the bulk of the available literature. The current literature review analysis aims to resolve the problems faced by researchers in the past by employing an unbiased statistical analysis to present and reveal the current trends and general belief of the scientific community regarding the anomalous heat transfer modes of nanofluids. The thermal performance analysis indicated that statistically there exists a variable enhancement for conduction, convection/mixed heat transfer, pool boiling heat transfer and critical heat flux modes. The most popular proposed mechanisms in the literature to explain heat transfer in nanofluids are revealed, as well as possible trends between nanofluid properties and thermal performance. The review also suggests future experimentation to provide more conclusive answers to the control mechanisms and influential parameters of heat transfer in nanofluids.

  15. Pulsatile flow of blood and heat transfer with variable viscosity under magnetic and vibration environment

    Science.gov (United States)

    Shit, G. C.; Majee, Sreeparna

    2015-08-01

    Unsteady flow of blood and heat transfer characteristics in the neighborhood of an overlapping constricted artery have been investigated in the presence of magnetic field and whole body vibration. The laminar flow of blood is taken to be incompressible and Newtonian fluid with variable viscosity depending upon temperature with an aim to provide resemblance to the real situation in the physiological system. The unsteady flow mechanism in the constricted artery is subjected to a pulsatile pressure gradient arising from systematic functioning of the heart and from the periodic body acceleration. The numerical computation has been performed using finite difference method by developing Crank-Nicolson scheme. The results show that the volumetric flow rate, skin-friction and the rate of heat transfer at the wall are significantly altered in the downstream of the constricted region. The axial velocity profile, temperature and flow rate increases with increase in temperature dependent viscosity, while the opposite trend is observed in the case of skin-friction and flow impedance.

  16. Simulation of Transient Nonlinear Friction-Induced Vibrations Using Complex Interface Modes: Application to the Prediction of Squeal Events

    Directory of Open Access Journals (Sweden)

    J.-J. Sinou

    2017-01-01

    Full Text Available During the past decades, the problem of friction-induced vibration and noise has been the subject of a huge amount of works. Various numerical simulations with finite elements models have been largely investigated to predict squeal events. Although a nonlinear analysis is more predictive than Complex Eigenvalues Analysis, one of the main drawbacks of the time analysis is the need of large computational efforts. In view of the complexity of the subject, this approach appears still computationally too expensive to be used in industry for finite element models. In this study, the potential of a new reduced model based on a double modal synthesis (i.e., a classical modal reduction via Craig and Bampton plus a condensation at the frictional interface based on complex modes for the prediction of self-excited vibrations of brake squeal is discussed. The effectiveness of the proposed modal reduction is tested on a finite element model of a simplified brake system. It will be shown that numerical results of times analysis by applying the proposed reduction correlate well with those of the nonlinear analysis based on a reference model, hence demonstrating the potential of using adapted modal reductions to predict the squeal propensity and to estimate self-excited vibrations and noise.

  17. Divertor heat flux simulations in ELMy H-mode discharges of EAST

    Science.gov (United States)

    Xia, T. Y.; Xu, X. Q.; Wu, Y. B.; Huang, Y. Q.; Wang, L.; Zheng, Z.; Liu, J. B.; Zang, Q.; Li, Y. Y.; Zhao, D.; EAST Team

    2017-11-01

    This paper presents heat flux simulations for the ELMy H-mode on the Experimental Advanced Superconducting Tokamak (EAST) using a six-field two-fluid model in BOUT++. Three EAST ELMy H-mode discharges with different plasma currents I p and geometries are studied. The trend of the scrape-off layer width λq with I p is reproduced by the simulation. The simulated width is only half of that derived from the EAST scaling law, but agrees well with the international multi-machine scaling law. Note that there is no radio-frequency (RF) heating scheme in the simulations, and RF heating can change the boundary topology and increase the flux expansion. Anomalous electron transport is found to contribute to the divertor heat fluxes. A coherent mode is found in the edge region in simulations. The frequency and poloidal wave number kθ are in the range of the edge coherent mode in EAST. The magnetic fluctuations of the mode are smaller than the electric field fluctuations. Statistical analysis of the type of turbulence shows that the turbulence transport type (blobby or turbulent) does not influence the heat flux width scaling. The two-point model differs from the simulation results but the drift-based model shows good agreement with simulations.

  18. Testing techniques and comparisons between theory and test for vibration modes of ring stiffened truncated-cone shells.

    Science.gov (United States)

    Naumann, E. C.

    1972-01-01

    Vibration tests were carried out on truncated-cone shells with widely spaced ring stiffeners. The models were excited by an air shaker for LF modes and by small electrodynamic shakers for HF modes. The Novozhilov thin shell theory according to which a ring is an assembly of an arbitrary number of segments, each being a short truncated-cone shell of uniform thickness, is used in the analysis of the results. A mobile, noncontacting, displacement-sensitive sensor system developed by the author was used in the tests. Tests results are given for a free-free 60-deg cone and for a clamped-free 60-deg cone. The tests are characterized as having considerable value for the classification of prevalent multimode responses in shells of this type.

  19. Free vibration analysis of rectangular plate with arbitrary edge constraints using characteristic orthogonal polynomials in assumed mode method

    Directory of Open Access Journals (Sweden)

    Kookhyun Kim

    2012-09-01

    Full Text Available An approximate method based on an assumed mode method has been presented for the free vibration analysis of a rectangular plate with arbitrary edge constraints. In the presented method, natural frequencies and their mode shapes of the plate are calculated by solving an eigenvalue problem of a multi-degree-of-freedom system matrix equation derived by using Lagrange's equations of motion. Characteristic orthogonal polynomials having the property of Timoshenko beam functions which satisfies edge constraints corresponding to those of the objective plate are used. In order to examine the accuracy of the proposed method, numerical examples of the rectangular plates with various thicknesses and edge constraints have been presented. The results have shown good agreement with those of other methods such as an analytic solution, an approximate solution, and a finite element analysis.

  20. A Simple Reduction Process for the Normal Vibrational Modes Occurring in Linear Molecules

    Science.gov (United States)

    McInerny, William

    2005-01-01

    The students in molecular spectroscopy courses are often required to determine the permitted normal vibrations for linear molecules that belong to particular groups. The reducible group representations generated by the use of Cartesian coordinates can be reduced by the use of a simple algebraic process applied to the group representations. The…

  1. Excess vibrational modes of a crystal in an external non-affine field

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Chemical Sciences; Volume 129; Issue 7. Excess vibrational ... While the former couples to external stress with familiar consequences, the response of a crystal when nonaffine displacements are enhanced using the thermodynamically conjugate field, is relatively less studied. We examine this ...

  2. Effects of Ultrasonic Vibration on Heat Transfer Characteristics of Lithium Bromide Aqueous Solution under the Reduced Pressure

    Science.gov (United States)

    Yamashiro, Hikaru; Nakashima, Ryou

    The effects of ultrasonic vibration on heat transfer characteristics of lithium bromide aqueous solution under the reduced pressures are studied experimentally. Pool boiling curves on horizontal smooth tube are obtained using distilled water and 50 % LiBr aqueous solution as test liquids. The system pressure p is varied from 12 to 101 kPa and the liquid subcooling ΔTsub ranges from 0 to 70 K. The frequency of ultrasonic vibration vi s set at 24 and 44 kHz, and the power input to the vibrator P is varied from 0 to 35 W. The wall superheat at the boiling incipience is found to decrease with increasing P, and the nucleate boiling curve shifts toward the lower wall temperature region. However, the effect of P is not found to be very significant in the high heat flux region, especially in the case of small liquid subcooling. Ultrasonic vibration is also found to improve the nucleate boiling heat transfer coefficient by up to a maximum of 3.5 times and to prevent crystallization of the solution and precipitation of additives.

  3. [A study of phonon vibration like modes for aggregation structure in silicate melts by high temperature Raman spectrum].

    Science.gov (United States)

    Xu, Pei-Cang; Li, Ru-Bi; Shang, Tong-Ming; Zhou, Jian; Sun, Jian-Hua; You, Jing-Lin

    2010-05-01

    Silicate melts are special fractal dimension system that is metastable state of near-way order and far-way disorder. In this paper, the size of nanometer aggregation structure and the frequences of phonon vibration like mode in the low dimension silicate series (CaO-Al2O3-SiO2 and Na2-Al2O3-SiO2 series) synthesized via high temperature melting and sol gel methods were measured by means of small-angle X-ray scattering (SAXS), low wavenumber Raman spectrum (LWRS) and high temperature Raman spectrum (HTRS in situ measuring). The nanometer self-similarity aggregation structure(it's size is about a few nm to a few tens nm) and phonic phonon vibration like modes of low temperature silicate gel, high temperature silicate melts and it's quenching glasses phases were obtained. So a quantitative method by HTRS for measuring the aggregation size in the high temperature melts was established. The results showed that the aggregation size of the silicate melts is smaller at high temperature than at room temperature and the number of bridge oxygen in one Si-O tetrahedron in network structure units is decreasing at high temperature. This study work provides important theory and information for deliberating geochemistry characteristic, crystallization & evolution of natural magma and enhancing performance of low dimension silicate matelials.

  4. Relationship between bond-breakage correlations and four-point correlations in heterogeneous glassy dynamics: configuration changes and vibration modes.

    Science.gov (United States)

    Shiba, Hayato; Kawasaki, Takeshi; Onuki, Akira

    2012-10-01

    We investigate the dynamic heterogeneities of glassy particle systems in the theoretical schemes of bond breakage and four-point correlation functions. In the bond-breakage scheme, we introduce the structure factor S(b)(q,t) and the susceptibility χ(b)(t) to detect the spatial correlations of configuration changes. Here χ(b)(t) attains a maximum at t=t(b)(max) as a function of time t, where the fraction of the particles with broken bonds φ(b)(t) is about 1/2. In the four-point scheme, treating the structure factor S(4)(q,t) and the susceptibility χ(4)(t), we detect superpositions of the heterogeneity of bond breakage and that of thermal low-frequency vibration modes. While the former grows slowly, the latter emerges quickly to exhibit complex space-time behavior. In two dimensions, the vibration modes extending over the system yield significant contributions to the four-point correlations, which depend on the system size logarithmically. A maximum of χ(4)(t) is attained at t=t(4)(max), where these two contributions become of the same order. As a result, t(4)(max) is considerably shorter than t(b)(max).

  5. Revealing silent vibration modes of nanomaterials by detecting anti-Stokes hyper-Raman scattering with femtosecond laser pulses.

    Science.gov (United States)

    Zeng, Jianhua; Chen, Lei; Dai, Qiaofeng; Lan, Sheng; Tie, Shaolong

    2016-01-21

    We proposed a scheme in which normal Raman scattering is coupled with hyper-Raman scattering for generating a strong anti-Stokes hyper-Raman scattering in nanomaterials by using femtosecond laser pulses. The proposal was experimentally demonstrated by using a single-layer MoS2 on a SiO2/Si substrate, a 17 nm-thick MoS2 on an Au/SiO2 substrate and a 9 nm-thick MoS2 on a SiO2-SnO2/Ag/SiO2 substrate which were confirmed to be highly efficient for second harmonic generation. A strong anti-Stokes hyper-Raman scattering was also observed in other nanomaterials possessing large second-order susceptibilities, such as silicon quantum dots self-assembled into "coffee" rings and tubular Cu-doped ZnO nanorods. In all the cases, many Raman inactive vibration modes were clearly revealed in the anti-Stokes hyper-Raman scattering. Apart from the strong anti-Stokes hyper-Raman scattering, Stokes hyper-Raman scattering with small Raman shifts was detected during the ablation process of thick MoS2 layers. It was also observed by slightly defocusing the excitation light. The detection of anti-Stokes hyper-Raman scattering may serve as a new technique for studying the Raman inactive vibration modes in nanomaterials.

  6. Local vibration of an elastic plate and zero-group velocity Lamb modes.

    Science.gov (United States)

    Prada, Claire; Clorennec, Dominique; Royer, Daniel

    2008-07-01

    Elastic plates or cylinders can support guided modes with zero group velocity (ZGV) at a nonzero value of the wave number. Using laser-based ultrasonic techniques, we experimentally investigate some fascinating properties of these ZGV modes: resonance and ringing effects, backward wave propagation, interference between backward and forward modes. Then, the conditions required for the existence of ZGV Lamb modes in isotropic plates are discussed. It is shown that these modes appear in a range of Poisson's ratio about the value for which the cutoff frequency curves of modes belonging to the same family intercept, i.e., for a bulk wave velocity ratio equal to a rational number. An interpretation of this phenomenon in terms of a strong repulsion between a pair of modes having a different parity in the vicinity of the cutoff frequencies is given. Experiments performed with materials of various Poisson's ratio demonstrate that the resonance spectrum of an unloaded elastic plate, locally excited by a laser pulse, is dominated by the ZGV Lamb modes.

  7. Small Externally-fueled Heat Pipe Thermionic Reactor (SEHPTR) for dual mode applications

    Science.gov (United States)

    Malloy, John; Jacox, Michael; Zubrin, Robert

    1992-07-01

    The Small Externally Fueled Heat-Pipe Thermionic Reactor (SEHPTR) is described in the context of applications as a dual-mode nuclear power source for satellites. The SEHPTR is a thermionic power system based on a reactor with modular fuel elements around cylindrical thermionic heat-pipe modules with diodes for heat rejection. The SEHPTR concept is theorized to be suitable for directly heating hydrogen gas in the core to increase propulsion and reduce orbit-transfer times. The advantages of dual-mode operation of the SEHPTR are listed including enhanced mission safety and performance at relatively low costs. The SEHPTR could provide direct thermal thrust and an integrated stage that symbiotically utilizes electric power, direct thrust, and hydrogen arcjets. The system is argued to be more effective than a nuclear power system designed solely for electrical power production.

  8. Anomalous heat transfer modes of nanofluids: a review based on statistical analysis

    OpenAIRE

    Sergis Antonis; Hardalupas Yannis

    2011-01-01

    Abstract This paper contains the results of a concise statistical review analysis of a large amount of publications regarding the anomalous heat transfer modes of nanofluids. The application of nanofluids as coolants is a novel practise with no established physical foundations explaining the observed anomalous heat transfer. As a consequence, traditional methods of performing a literature review may not be adequate in presenting objectively the results representing the bulk of the available l...

  9. Impacts of Climate Modes on Air–Sea Heat Exchange in the Red Sea

    KAUST Repository

    Abualnaja, Yasser

    2015-04-01

    The impacts of various climate modes on the Red Sea surface heat exchange are investigated using the MERRA reanalysis and the OAFlux satellite reanalysis datasets. Seasonality in the atmospheric forcing is also explored. Mode impacts peak during boreal winter [December–February (DJF)] with average anomalies of 12–18 W m−2 to be found in the northern Red Sea. The North Atlantic Oscillation (NAO), the east Atlantic–west Russia (EAWR) pattern, and the Indian monsoon index (IMI) exhibit the strongest influence on the air–sea heat exchange during the winter. In this season, the largest negative anomalies of about −30 W m−2 are associated with the EAWR pattern over the central part of the Red Sea. In other seasons, mode-related anomalies are considerably lower, especially during spring when the mode impacts are negligible. The mode impacts are strongest over the northern half of the Red Sea during winter and autumn. In summer, the southern half of the basin is strongly influenced by the multivariate ENSO index (MEI). The winter mode–related anomalies are determined mostly by the latent heat flux component, while in summer the shortwave flux is also important. The influence of the modes on the Red Sea is found to be generally weaker than on the neighboring Mediterranean basin.

  10. Impacts of Atmospheric Modes of Variability on Air-Sea Heat Exchange in the Red Sea

    Science.gov (United States)

    Abualnaja, Yasser O.; Papadopoulos, Vassilis P.; Josey, Simon A.; Hoteit, Ibrahim; Kontoyiannis, Harilaos; Raitsos, Dionissios E.

    2014-05-01

    The potential impacts on Red Sea surface heat exchange of various major modes of atmospheric variability are investigated using the NASA Modern Era Retrospective Analysis for Research and Applications (MERRA) atmospheric reanalysis and the Objectively Analyzed Air-Sea Flux dataset (OAFlux) merged satellite+reanalysis dataset. The mode impacts on surface net heat flux are quantified by calculating the heat flux anomaly that corresponds to a unit positive value of each index for each grid point. The seasonal effects of the atmospheric forcing are investigated considering two and four typical seasons of a calendar year. Considering two seasons, the impacts are strongest during the winter-centered part of the year (October to March) mainly over the northern sub-basin. The North Atlantic Oscillation (NAO), the East Atlantic - West Russia Pattern (EAWR), and the Indian Monsoon Index (IMI) have the greatest effects. They generate negative anomalies (by definition additional ocean heat loss) of 7-12 W/m2 in the northern Red Sea basin mean net heat flux for a unit positive value of the mode index. During the summer (April to September), the signal is smaller and the East Atlantic (EA) and Multivariate ENSO Index (MEI) modes have the strongest impact which is now located in the southern Red Sea (sub-basin anomalies of 4 W/m2 for unit positive mode index, negative for EA and positive for MEI). Results obtained by analysis carried out on the traditional four-season basis reveal that indices impact peaks during the typical boreal winter (DJF) with average anomalies of 12-18 W/m2 to be found in the northern part. It is noteworthy that during the winter, the EAWR generates negative anomalies around 30 W/m2 over the most of the central Red Sea. During the spring (MAM), summer (JJA) and autumn (SON) the anomalies are considerably lower, especially during the spring when the mode impacts are negligible. Atmospheric modes have a stronger effect on air-sea heat flux over the northern

  11. Sensing Performance Analysis on Quartz Tuning Fork-Probe at the High Order Vibration Mode for Multi-Frequency Scanning Probe Microscopy

    Directory of Open Access Journals (Sweden)

    Xiaofei Zhang

    2018-01-01

    Full Text Available Multi-frequency scanning near-field optical microscopy, based on a quartz tuning fork-probe (QTF-p sensor using the first two orders of in-plane bending symmetrical vibration modes, has recently been developed. This method can simultaneously achieve positional feedback (based on the 1st in-plane mode called the low mode and detect near-field optically induced forces (based on the 2nd in-plane mode called the high mode. Particularly, the high mode sensing performance of the QTF-p is an important issue for characterizing the tip-sample interactions and achieving higher resolution microscopic imaging but the related researches are insufficient. Here, we investigate the vibration performance of QTF-p at high mode based on the experiment and finite element method. The frequency spectrum characteristics are obtained by our homemade laser Doppler vibrometer system. The effects of the properties of the connecting glue layer and the probe features on the dynamic response of the QTF-p sensor at the high mode are investigated for optimization design. Finally, compared with the low mode, an obvious improvement of quality factor, of almost 50%, is obtained at the high mode. Meanwhile, the QTF-p sensor has a high force sensing sensitivity and a large sensing range at the high mode, indicating a broad application prospect for force sensing.

  12. Sensing Performance Analysis on Quartz Tuning Fork-Probe at the High Order Vibration Mode for Multi-Frequency Scanning Probe Microscopy.

    Science.gov (United States)

    Zhang, Xiaofei; Gao, Fengli; Li, Xide

    2018-01-24

    Multi-frequency scanning near-field optical microscopy, based on a quartz tuning fork-probe (QTF-p) sensor using the first two orders of in-plane bending symmetrical vibration modes, has recently been developed. This method can simultaneously achieve positional feedback (based on the 1st in-plane mode called the low mode) and detect near-field optically induced forces (based on the 2nd in-plane mode called the high mode). Particularly, the high mode sensing performance of the QTF-p is an important issue for characterizing the tip-sample interactions and achieving higher resolution microscopic imaging but the related researches are insufficient. Here, we investigate the vibration performance of QTF-p at high mode based on the experiment and finite element method. The frequency spectrum characteristics are obtained by our homemade laser Doppler vibrometer system. The effects of the properties of the connecting glue layer and the probe features on the dynamic response of the QTF-p sensor at the high mode are investigated for optimization design. Finally, compared with the low mode, an obvious improvement of quality factor, of almost 50%, is obtained at the high mode. Meanwhile, the QTF-p sensor has a high force sensing sensitivity and a large sensing range at the high mode, indicating a broad application prospect for force sensing.

  13. Blade Vibration Measurement System for Characterization of Closely Spaced Modes and Mistuning Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Phase I project successfully demonstrated that the advanced non-contacting stress measurement system (NSMS) was able to address closely spaced modes and...

  14. Vibration measurements of high-heat-load monochromators for DESY PETRA III extension

    Energy Technology Data Exchange (ETDEWEB)

    Kristiansen, Paw, E-mail: paw.kristiansen@fmb-oxford.com [FMB Oxford Ltd, Unit 1 Ferry Mills, Oxford OX2 0ES (United Kingdom); Horbach, Jan; Döhrmann, Ralph; Heuer, Joachim [DESY, Deutsches Elektronen-Synchrotron Hamburg, Notkestrasse 85, 22607 Hamburg (Germany)

    2015-05-09

    Vibration measurements of a cryocooled double-crystal monochromator are presented. The origins of the vibrations are identified. The minimum achieved vibration of the relative pitch between the two crystals is 48 nrad RMS and the minimum achieved absolute vibration of the second crystal is 82 nrad RMS. The requirement for vibrational stability of beamline optics continues to evolve rapidly to comply with the demands created by the improved brilliance of the third-generation low-emittance storage rings around the world. The challenge is to quantify the performance of the instrument before it is installed at the beamline. In this article, measurement techniques are presented that directly and accurately measure (i) the relative vibration between the two crystals of a double-crystal monochromator (DCM) and (ii) the absolute vibration of the second-crystal cage of a DCM. Excluding a synchrotron beam, the measurements are conducted under in situ conditions, connected to a liquid-nitrogen cryocooler. The investigated DCM utilizes a direct-drive (no gearing) goniometer for the Bragg rotation. The main causes of the DCM vibration are found to be the servoing of the direct-drive goniometer and the flexibility in the crystal cage motion stages. It is found that the investigated DCM can offer relative pitch vibration down to 48 nrad RMS (capacitive sensors, 0–5 kHz bandwidth) and absolute pitch vibration down to 82 nrad RMS (laser interferometer, 0–50 kHz bandwidth), with the Bragg axis brake engaged.

  15. Performance of Chilled Beam with Radial Swirl Jet and Diffuse Ceiling Air Supply in Heating Mode

    DEFF Research Database (Denmark)

    Bertheussen, Bård; Mustakallio, Panu; Melikov, Arsen Krikor

    2013-01-01

    The performance of diffuse ceiling air supply and chilled beam with swirl jet (CSW) in heating mode (winter situation) was studied and compared with regard to the generated indoor environment. An office mock-up with one occupant was simulated in a test room (4.5 x 3.95 x 3.5 m3 (L x W x H...

  16. Theoretical analysis of mode conversion electron heating experiments in Alcator C-Mod

    Energy Technology Data Exchange (ETDEWEB)

    Bonoli, P.T.; OShea, P.J. [MIT PSFC, Cambridge, Massachusetts 02139 (United States); Brambilla, M. [Max Planck Institut fuer Plasmaphysik, 85748 Garching (Germany); Hubbard, A.; Porkolab, M.; Takase, Y.; Wukitch, S. [MIT PSFC, Cambridge, Massachusetts 02139 (United States)

    1997-04-01

    A computer code is used for analysis of the electron heating and current drive at 80 and 40 MHz via mode converted ion Bernstein waves in the Alcator C-Mod tokamak. The results will be tested experimentally. {copyright} {ital 1997 American Institute of Physics.}

  17. Ion heat transport dynamics during edge localized mode cycles at ASDEX Upgrade

    Science.gov (United States)

    Viezzer, E.; Cavedon, M.; Fable, E.; Laggner, F. M.; McDermott, R. M.; Galdon-Quiroga, J.; Dunne, M. G.; Kappatou, A.; Angioni, C.; Cano-Megias, P.; Cruz-Zabala, D. J.; Dux, R.; Pütterich, T.; Ryter, F.; Wolfrum, E.; The ASDEX Upgrade Team; The EUROfusion MST1 Team

    2018-02-01

    The edge ion heat transport is analyzed in ASDEX Upgrade (AUG) by combining a comprehensive set of pedestal measurements with both interpretive and predictive modelling. The experimentally determined ion heat diffusivities, χi , are compared with neoclassical theory and the impact of edge localized modes (ELMs) on the edge ion heat transport level is studied in detail. Pedestal matching experiments in deuterium and hydrogen plasmas show that the inter-ELM pedestal χi remains close to the neoclassical value. The additional power needed in hydrogen to get similar pedestal temperatures as in deuterium plasmas mostly affects the electron heat channel, i.e. the electron heat diffusivity increases while the ion heat diffusivity stays at the same level within the uncertainties. Sub-ms measurements of the edge ion temperature allows us to extend the analysis to the entire ELM cycle. During the ELM crash, the ion heat transport is increased by an order of magnitude. The perturbed heat flux increases first at the separatrix, i.e. first the separatrix ion temperature increases, leading to a flatter ion temperature gradient, followed by a decrease of the whole pedestal profile. The ion heat transport returns to its pre-ELM neoclassical level 3–4 ms after the ELM crash.

  18. Electron heating and mode transition in dual frequency atmospheric pressure argon dielectric barrier discharge

    Science.gov (United States)

    Zhang, Z. L.; Lim, J. W. M.; Nie, Q. Y.; Zhang, X. N.; Jiang, B. H.

    2017-10-01

    Plasma ionization, excitation, mode transitions and associated electron heating mechanisms in atmospheric pressure dielectric barrier discharges (DBD) driven by dual radio frequency sources are investigated in this paper. The electrons are found to be heated mainly by the high frequency component in the plasma bulk when discharged in α mode. On the contrary, the low frequency component is primarily responsible for heating in the sheath which is caused by intense motion in the sheath. It was also found that variation of the lower frequency component ratio could effectively modulate the electron energy distribution as determined from time averaged EEDF. The results above have demonstrated that the independent control of plasma parameters via non-linear synergistic effect between the dual frequency sources can be achieved through reasonable selection of processing parameters.

  19. Radiofrequency-heated enhanced confinement modes in the Alcator C-Mod tokamak

    Energy Technology Data Exchange (ETDEWEB)

    Takase, Y.; Boivin, R.L.; Bombarda, F.; Bonoli, P.T.; Christensen, C.; Fiore, C.; Garnier, D.; Goetz, J.A.; Golovato, S.N.; Granetz, R.; Greenwald, M.; Horne, S.F.; Hubbard, A.; Hutchinson, I.H.; Irby, J.; LaBombard, B.; Lipschultz, B.; Marmar, E.; May, M.; Mazurenko, A.; McCracken, G.; OShea, P.; Porkolab, M.; Reardon, J.; Rice, J.; Rost, C.; Schachter, J.; Snipes, J.A.; Stek, P.; Terry, J.; Watterson, R.; Welch, B.; Wolfe, S. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

    1997-05-01

    Enhanced confinement modes up to a toroidal field of B{sub T}=8T have been studied with up to 3.5 MW of radiofrequency (rf) heating power in the ion cyclotron range of frequencies (ICRF) at 80 MHz. H-mode is observed when the edge temperature exceeds a threshold value. The high confinement mode (H-mode) with higher confinement enhancement factors (H) and longer duration became possible after boronization by reducing the radiated power from the main plasma. A quasi-steady state with high confinement (H=2.0), high normalized beta ({beta}{sub N}=1.5), low radiated power fraction (P{sub rad}{sup main}/P{sub loss}=0.3), and low effective charge (Z{sub eff}=1.5) has been obtained in Enhanced D{sub {alpha}} H-mode. This type of H-mode has enhanced levels of continuous D{sub {alpha}} emission and very little or no edge localized mode (ELM) activity, and reduced core particle confinement time relative to ELM-free H-mode. The pellet enhanced performance (PEP) mode is obtained by combining core fueling with pellet injection and core heating. A highly peaked pressure profile with a central value of 8 atmospheres was observed. The steep pressure gradient drives off-axis bootstrap current, resulting in a shear reversed safety factor (q) profile. Suppression of sawteeth appears to be important in maintaining the highly peaked pressure profile. Lithium pellets were found to be more effective than deuterium pellets in raising q{sub 0}. {copyright} {ital 1997 American Institute of Physics.}

  20. Observation of a universal donor-dependent vibrational mode in graphene.

    Science.gov (United States)

    Fedorov, A V; Verbitskiy, N I; Haberer, D; Struzzi, C; Petaccia, L; Usachov, D; Vilkov, O Y; Vyalikh, D V; Fink, J; Knupfer, M; Büchner, B; Grüneis, A

    2014-01-01

    Electron-phonon coupling and the emergence of superconductivity in intercalated graphite have been studied extensively. Yet, phonon-mediated superconductivity has never been observed in the 2D equivalent of these materials, doped monolayer graphene. Here we perform angle-resolved photoemission spectroscopy to try to find an electron donor for graphene that is capable of inducing strong electron-phonon coupling and superconductivity. We examine the electron donor species Cs, Rb, K, Na, Li, Ca and for each we determine the full electronic band structure, the Eliashberg function and the superconducting critical temperature Tc from the spectral function. An unexpected low-energy peak appears for all dopants with an energy and intensity that depend on the dopant atom. We show that this peak is the result of a dopant-related vibration. The low energy and high intensity of this peak are crucially important for achieving superconductivity, with Ca being the most promising candidate for realizing superconductivity in graphene.

  1. Divertor heat load in ASDEX Upgrade L-mode in presence of external magnetic perturbation

    Science.gov (United States)

    Faitsch, M.; Sieglin, B.; Eich, T.; Herrmann, A.; Suttrop, W.; the ASDEX Upgrade Team

    2017-09-01

    Power exhaust is one of the major challenges for a future fusion device. Applying a non-axisymmetric external magnetic perturbation is one technique that is studied in order to mitigate or suppress large edge localized modes which accompany the high confinement regime in tokamaks. The external magnetic perturbation induces breaking in the axisymmetry of a tokamak and leads to a 2D heat flux pattern on the divertor target. The 2D heat flux pattern at the outer divertor target is studied on ASDEX Upgrade in stationary L-mode discharges. The amplitude of the 2D characteristic of the heat flux depends on the alignment between the field lines at the edge and the vacuum response of the applied magnetic perturbation spectrum. The 2D characteristic reduces with increasing density. The increasing divertor broadening, S, with increasing density is proposed as the main actuator. This is supported by a generic model using field line tracing and the vacuum field approach that is in quantitative agreement with the measured heat flux. The perturbed heat flux, averaged over a full toroidal rotation of the magnetic perturbation, is identical to the non-perturbed heat flux without magnetic perturbation. The transport qualifiers, power fall-off length {λ }q and divertor broadening, S, are the same within the uncertainty compared to the unperturbed reference. No additional cross field transport is observed.

  2. Correlating mode-I fracture toughness and mechanical properties of heat-treated crystalline rocks

    Directory of Open Access Journals (Sweden)

    Mayukh Talukdar

    2018-02-01

    Full Text Available For the effect of thermal treatment on the mode-I fracture toughness (FT, three crystalline rocks (two basalts and one tonalite were experimentally investigated. Semi-circular bend specimens of the rocks were prepared following the method suggested by the International Society for Rock Mechanics (ISRM and were treated at various temperatures ranging from room temperature (25 °C to 600 °C. Mode-I FT was correlated with tensile strength (TS, ultrasonic velocities, and Young's modulus (YM. Additionally, petrographic and X-ray diffraction analyses were carried out to find the chemical changes resulting from the heat treatment. Further, scanning electron microscopy (SEM was conducted to observe the micro structural changes when subjected to high temperatures. These experiments demonstrate that heat treatment has a strong negative impact on the FT and mechanical properties of the rocks. From room temperature to 600 °C, mode-I FT values of massive basalt, giant plagioclase basalt, and tonalite were reduced by nearly 52%, 68%, and 64%, respectively. Also, at all temperature levels, FT and mechanical properties are found to be exponentially correlated. However, the exact nature of the relationship mainly depends on rock type. Besides, TS was found to be a better indicator of degradation degree than the mode-I FT. SEM images show that micro crack density and structural disintegration of the mineral grains increase with temperature. These physical changes confirm the observed reduction in the stiffness of heat-treated crystalline rocks.

  3. A dual-mode textile for human body radiative heating and cooling.

    Science.gov (United States)

    Hsu, Po-Chun; Liu, Chong; Song, Alex Y; Zhang, Ze; Peng, Yucan; Xie, Jin; Liu, Kai; Wu, Chun-Lan; Catrysse, Peter B; Cai, Lili; Zhai, Shang; Majumdar, Arun; Fan, Shanhui; Cui, Yi

    2017-11-01

    Maintaining human body temperature is one of the most basic needs for living, which often consumes a huge amount of energy to keep the ambient temperature constant. To expand the ambient temperature range while maintaining human thermal comfort, the concept of personal thermal management has been recently demonstrated in heating and cooling textiles separately through human body infrared radiation control. Realizing these two opposite functions within the same textile would represent an exciting scientific challenge and a significant technological advancement. We demonstrate a dual-mode textile that can perform both passive radiative heating and cooling using the same piece of textile without any energy input. The dual-mode textile is composed of a bilayer emitter embedded inside an infrared-transparent nanoporous polyethylene (nanoPE) layer. We demonstrate that the asymmetrical characteristics of both emissivity and nanoPE thickness can result in two different heat transfer coefficients and achieve heating when the low-emissivity layer is facing outside and cooling by wearing the textile inside out when the high-emissivity layer is facing outside. This can expand the thermal comfort zone by 6.5°C. Numerical fitting of the data further predicts 14.7°C of comfort zone expansion for dual-mode textiles with large emissivity contrast.

  4. Investigation of polyvinylidene fluoride (PVDF) films in identifying high-frequency vibration modes of flexible plates.

    Science.gov (United States)

    Chuang, Kuo-Chih; Liou, Hong-Cin; Ma, Chien-Ching

    2014-06-01

    Compared with piezoelectric ceramics such as lead zirconate titanate (PZT) ceramics, the low density and high compliance of the PVDF films make them a more suitable choice in modal testing, especially for detecting high-frequency modes in flexible or inflatable structures. In this work, dynamic sensing performances of PVDF films for flexible structures in modal testing are examined, with considerations including the repeatability of the impact source, the accuracy of the sensing responses, and the influences of the nodal lines on the frequency spectra of the transient responses. Two flexible plates with different boundary conditions and thickness are considered. Experimental results, compared with FEM computations or theoretical predictions, demonstrate the excellent dynamic sensing performance of the PVDF film in modal testing applications, especially for identification of high-frequency modes on flexible structures.

  5. Vibration suppression in flexible structures via the sliding-mode control approach

    Science.gov (United States)

    Drakunov, S.; Oezguener, Uemit

    1994-01-01

    Sliding mode control became very popular recently because it makes the closed loop system highly insensitive to external disturbances and parameter variations. Sliding algorithms for flexible structures have been used previously, but these were based on finite-dimensional models. An extension of this approach for differential-difference systems is obtained. That makes if possible to apply sliding-mode control algorithms to the variety of nondispersive flexible structures which can be described as differential-difference systems. The main idea of using this technique for dispersive structures is to reduce the order of the controlled part of the system by applying an integral transformation. We can say that transformation 'absorbs' the dispersive properties of the flexible structure as the controlled part becomes dispersive.

  6. Nonlinear vibration analysis of axially moving strings based on gyroscopic modes decoupling

    Science.gov (United States)

    Yang, Xiao-Dong; Wu, Hang; Qian, Ying-Jing; Zhang, Wei; Lim, C. W.

    2017-04-01

    A novel idea that applies the multiple scale analysis to a discretized decoupled system of gyroscopic continua is introduced and an axial moving string is treated as an example. First, the invariant manifold method is applied to the discretized ordinary differential equations of the axially moving string. Complex gyroscopic mode functions that agree well with true analytical results are obtained. The gyroscopic modes are subsequently used for the discretized ordinary differential equations with gyroscopic and nonlinear coupling terms that yield a gyroscopically decoupled system. Further the method of multiple scales is used to obtain the equations at a slow scale. This novel procedure is compared to solutions obtained by directly applying the classical multiple scale analysis to the gyroscopically coupled system without decoupling. The modal decoupled system analysis yields better frequency with comparing to the classic method. The proposed methodology provides a novel alternative for nonlinear dynamic analysis of gyroscopic continua.

  7. Analytical aspects of Randomdec analysis. [for vibration modes and nondestructive flaw detection

    Science.gov (United States)

    Reed, R. E.

    1979-01-01

    Relationships between Randomdec analysis and conventional methods of analysis such as Fourier and modal analysis are shown. The Randomdec signature is described in terms of the Fourier amplitude coefficients. Using this result, the effect of filtering the time history is shown. For a linear, two mode model, signatures are compared to the free response of the system subjected to different initial conditions to show the relationship of displacement and acceleration signatures to the physical system. Detection and location of flaws is also discussed.

  8. Residual mode correction in calibrating nonlinear damper for vibration control of flexible structures

    Science.gov (United States)

    Sun, Limin; Chen, Lin

    2017-10-01

    Residual mode correction is found crucial in calibrating linear resonant absorbers for flexible structures. The classic modal representation augmented with stiffness and inertia correction terms accounting for non-resonant modes improves the calibration accuracy and meanwhile avoids complex modal analysis of the full system. This paper explores the augmented modal representation in calibrating control devices with nonlinearity, by studying a taut cable attached with a general viscous damper and its Equivalent Dynamic Systems (EDSs), i.e. the augmented modal representations connected to the same damper. As nonlinearity is concerned, Frequency Response Functions (FRFs) of the EDSs are investigated in detail for parameter calibration, using the harmonic balance method in combination with numerical continuation. The FRFs of the EDSs and corresponding calibration results are then compared with those of the full system documented in the literature for varied structural modes, damper locations and nonlinearity. General agreement is found and in particular the EDS with both stiffness and inertia corrections (quasi-dynamic correction) performs best among available approximate methods. This indicates that the augmented modal representation although derived from linear cases is applicable to a relatively wide range of damper nonlinearity. Calibration of nonlinear devices by this means still requires numerical analysis while the efficiency is largely improved owing to the system order reduction.

  9. Intermolecular vibrational modes and H-bond interactions in crystalline urea investigated by terahertz spectroscopy and theoretical calculation

    Science.gov (United States)

    Zhao, Yonghong; Li, Zhi; Liu, Jianjun; Hu, Cong; Zhang, Huo; Qin, Binyi; Wu, Yifang

    2018-01-01

    The characteristic absorption spectra of crystalline urea in 0.6-1.8 THz region have been measured by terahertz time-domain spectroscopy at room temperature experimentally. Five broad absorption peaks were observed at 0.69, 1.08, 1.27, 1.47 and 1.64 THz respectively. Moreover, density functional theory (DFT) calculation has been performed for the isolated urea molecule, and there is no infrared intensity in the region below 1.8 THz. This means that single molecule calculations are failure to predict the experimental spectra of urea crystals. To simulate these spectra, calculations on a cluster of seven urea molecules using M06-2X and B3LYP-D3 are performed, and we found that M06-2X perform better. The observed THz vibrational modes are assigned to bending and torsional modes related to the intermolecular H-bond interactions with the help of potential energy distribution (PED) method. Using the reduced-density-gradient (RDG) analysis, the positions and types of intermolecular H-bond interactions in urea crystals are visualized. Therefore, we can confirm that terahertz spectroscopy can be used as an effective means to detect intermolecular H-bond interactions in molecular crystals.

  10. Charge-sensitive vibrational modes in the (EDT-TTF-OX)2AsF6 chiral molecular conductors

    Science.gov (United States)

    Olejniczak, Iwona; Frąckowiak, Arkadiusz; Matysiak, Jacek; Madalan, Augustin; Pop, Flavia; Avarvari, Narcis

    2014-03-01

    Infrared and Raman spectra of three chiral molecular conductors (EDT-TTF-OX)2AsF6, comprising of two salts based on enantiopure EDT-TTF-OX donor molecules and one based on their racemic mixture, have been measured as a function of temperature. In the frequency range of the C=C stretching vibrations of EDT-TTF-OX, charge-sensitive modes are identified based on theoretical calculations for neutral and oxidized EDT-TTF-OX using density functional theory (DFT) methods. The positions of C=C stretching modes in both Raman and infrared spectra of the (EDT-TTF-OX)2AsF6 materials are analyzed assuming a linear relationship between the frequency and charge of the molecule. The charge density on the EDTTTF-OX donor molecule is estimated to be +0.5 in all investigated materials and does not change with temperature. Therefore we suggest, that M-I transition observed in (EDT-TTF-OX)2AsF6 chiral molecular conductors at low temperature is not related to the charge ordering mechanism.

  11. Oversampling in virtual visual sensors as a means to recover higher modes of vibration

    Science.gov (United States)

    Shariati, Ali; Schumacher, Thomas

    2015-03-01

    Vibration-based structural health monitoring (SHM) techniques require modal information from the monitored structure in order to estimate the location and severity of damage. Natural frequencies also provide useful information to calibrate finite element models. There are several types of physical sensors that can measure the response over a range of frequencies. For most of those sensors however, accessibility, limitation of measurement points, wiring, and high system cost represent major challenges. Recent optical sensing approaches offer advantages such as easy access to visible areas, distributed sensing capabilities, and comparatively inexpensive data recording while having no wiring issues. In this research we propose a novel methodology to measure natural frequencies of structures using digital video cameras based on virtual visual sensors (VVS). In our initial study where we worked with commercially available inexpensive digital video cameras we found that for multiple degrees of freedom systems it is difficult to detect all of the natural frequencies simultaneously due to low quantization resolution. In this study we show how oversampling enabled by the use of high-end high-frame-rate video cameras enable recovering all of the three natural frequencies from a three story lab-scale structure.

  12. Spectral intensities in cubic systems. I. Progressions based upon parity vibrational modes

    Energy Technology Data Exchange (ETDEWEB)

    Acevedo, R.; Vasquez, S.O. [Department of Basic Chemistry, Faculty of Physical and Mathematical Sciences, University of Chile. Tupper 2069, Casilla 2777, Santiago, Chile (Chile); Meruane, T. [Department of Chemistry, Universidad Metropolitana de Ciencias de la Educacion. Av. J.P. Alessandri 774, Casilla 147, C. Santiago, Chile (Chile); Poblete, V. [Department of Nuclear Materials, Lo Aguirre, Comision Chilena de Energia Nuclear. Amunategui 95, Casilla 188-D, Santiago, Chile (Chile); Pozo, J. [Facultad de Ciencias de la Ingenieria. Universidad Diego Portales. Casilla 298-V, Santiago, Chile (Chile)

    1998-12-01

    The well-resolved emission and absorption spectra of centrosymmetric coordination compounds of the transition metal ions have been used widely to provide the experimental data against which to test theoretical models of vibronic intensities. With reference to the {sup 2} E{sub g} {yields} {sup 4} A{sub 2g} luminescence transition, at a perfect octahedral site in Cs{sub 2}SiF{sub 6}, over than one hundred vibronic lines are observed with line widths of a few wavenumber spread over some 3000 cm{sup -1}. This paper reports a through examination of both the electronic and vibrational factors, which influences the observed vibronic intensities of the various assigned and identified lines in the spectra of the MnF{sub 6} {sup 2-} complex ion in the Cs{sub 2}SiF{sub 6} cubic lattice. The origin and nature of higher order vibronic interactions are analysed on the basis of a symmetrized vibronic crystal field-ligand polarization model. (Author)

  13. Multicriteria hierarchical iterative interactive algorithm for organizing operational modes of large heat supply systems

    Science.gov (United States)

    Korotkova, T. I.; Popova, V. I.

    2017-11-01

    The generalized mathematical model of decision-making in the problem of planning and mode selection providing required heat loads in a large heat supply system is considered. The system is multilevel, decomposed into levels of main and distribution heating networks with intermediate control stages. Evaluation of the effectiveness, reliability and safety of such a complex system is carried out immediately according to several indicators, in particular pressure, flow, temperature. This global multicriteria optimization problem with constraints is decomposed into a number of local optimization problems and the coordination problem. An agreed solution of local problems provides a solution to the global multicriterion problem of decision making in a complex system. The choice of the optimum operational mode of operation of a complex heat supply system is made on the basis of the iterative coordination process, which converges to the coordinated solution of local optimization tasks. The interactive principle of multicriteria task decision-making includes, in particular, periodic adjustment adjustments, if necessary, guaranteeing optimal safety, reliability and efficiency of the system as a whole in the process of operation. The degree of accuracy of the solution, for example, the degree of deviation of the internal air temperature from the required value, can also be changed interactively. This allows to carry out adjustment activities in the best way and to improve the quality of heat supply to consumers. At the same time, an energy-saving task is being solved to determine the minimum required values of heads at sources and pumping stations.

  14. Microwave pre-heating of natural rubber using a rectangular wave guide (MODE: TE10

    Directory of Open Access Journals (Sweden)

    Doo-ngam, N.

    2007-11-01

    Full Text Available This paper presents an application of microwave radiation for pre-heating of natural rubbercompounding with various sulphur contents. The natural rubber-compounding was pre-heated by microwave radiation using a rectangular wave guide system (MODE: TE10 operating at frequency of 2.45 GHz in which the power can vary from 0 to 1500 W. In the present work, the influence of power input, sample thickness, and sulphur content were examined after applying microwave radiation to the rubber samples. Results are discussed regarding the thermal properties, 3-D network, dielectric properties and chemical structures. From the result, firstly, it was found that microwave radiation can be applied to pre-heating natural rubber-compounding before the vulcanization process. Secondly, microwave radiation was very useful for pre-heating natural rubber-compounding that has a thickness greater than 5mm. Thirdly, crosslinking in natural rubber-compounding may occurs after pre-heating by microwave radiation though Fourier Transform Infrared Spectroscopy(FTIR. Finally, there a little effect of sulphur content on temperature profiles after applying microwave radiation to the natural rubber-compounding. Moreover, natural rubber-compounding without carbon black showed a lower heat absorption compared with natural rubbercompounding filled carbon black. This is due to the difference in dielectric loss factor. This preliminary result will be useful information in terms of microwave radiation for pre-heating natural rubber-compounding and rubber processing in industry.

  15. Blind identification of full-field vibration modes from video measurements with phase-based video motion magnification

    Science.gov (United States)

    Yang, Yongchao; Dorn, Charles; Mancini, Tyler; Talken, Zachary; Kenyon, Garrett; Farrar, Charles; Mascareñas, David

    2017-02-01

    user supervision and calibration. First a multi-scale image processing method is applied on the frames of the video of a vibrating structure to extract the local pixel phases that encode local structural vibration, establishing a full-field spatiotemporal motion matrix. Then a high-spatial dimensional, yet low-modal-dimensional, over-complete model is used to represent the extracted full-field motion matrix using modal superposition, which is physically connected and manipulated by a family of unsupervised learning models and techniques, respectively. Thus, the proposed method is able to blindly extract modal frequencies, damping ratios, and full-field (as many points as the pixel number of the video frame) mode shapes from line of sight video measurements of the structure. The method is validated by laboratory experiments on a bench-scale building structure and a cantilever beam. Its ability for output (video measurements)-only identification and visualization of the weakly-excited mode is demonstrated and several issues with its implementation are discussed.

  16. Control of input delayed pneumatic vibration isolation table using adaptive fuzzy sliding mode

    Directory of Open Access Journals (Sweden)

    Mostafa Khazaee

    Full Text Available AbstractPneumatic isolators are promising candidates for increasing the quality of accurate instruments. For this purpose, higher performance of such isolators is a prerequisite. In particular, the time-delay due to the air transmission is an inherent issue with pneumatic systems, which needs to be overcome using modern control methods. In this paper an adaptive fuzzy sliding mode controller is proposed to improve the performance of a pneumatic isolator in the low frequency range, i.e., where the passive techniques have obvious shortcomings. The main idea is to combine the adaptive fuzzy controller with adaptive predictor as a new time delay control technique. The adaptive fuzzy sliding mode control and the adaptive fuzzy predictor help to circumvent the input delay and nonlinearities in such isolators. The main advantage of the proposed method is that the closed-loop system stability is guaranteed under certain conditions. Simulation results reveal the effectiveness of the proposed method, compared with other existing time -delay control methods.

  17. Material Properties of Various Cast Aluminum Alloys Made Using a Heated Mold Continuous Casting Technique with and without Ultrasonic Vibration

    Directory of Open Access Journals (Sweden)

    Mitsuhiro Okayasu

    2015-08-01

    Full Text Available This work was carried out to develop high-quality cast aluminum alloys using a new casting technology. For this purpose, commercial Al alloys were created by heated mold continuous casting (HMC with ultrasonic vibration (UV. With the HMC process, the grain size and the crystal orientation of the Al alloys were controlled, i.e., fine grains with a uniformly organized lattice formation. In addition, an attempt was made to modify the microstructural formation by cavitation. These microstructural characteristics made excellent mechanical properties. Using UV in the continuous casting process, more fine and spherical grains were slightly disordered, which was detected using electron backscattered diffraction. The mechanical properties of the UV HMC Al alloys were slightly higher than those for the related cast Al alloys without UV. Moreover, the severe vibration caused higher mechanical properties. The lattice and dislocation characteristics of the cast samples made with and without UV processes were analyzed systematically using electron backscattered diffraction.

  18. An assumed mode method and finite element method investigation of the coupled vibration in a flexible-disk rotor system with lacing wires

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Shui-Ting; Huang, Hong-Wu [Hunan University, Changsha (China); Chiu, Yi-Jui; Yu, Guo-Fei [Xiamen University of Technology, Xiamen (China); Yang, Chia-Hao [Taipei Chengshih University of Science and Technology, Taipei (China); Jian, Sheng-Rui [I-Shou University, Kaohsiung (China)

    2017-02-15

    The Assumed mode method (AMM) and Finite element method (FEM) were used. Their results were compared to investigate the coupled shaft-torsion, disk-transverse, and blade-bending vibrations in a flexible-disk rotor system. The blades were grouped with a spring. The flexible-disk rotor system was divided into three modes of coupled vibrations: Shaft-disk-blade, disk-blade, and blade-blade. Two new modes of coupled vibrations were introduced, namely, lacing wires-blade and lacing wires-disk-blade. The patterns of change of the natural frequencies and mode shapes of the system were discussed. The results showed the following: first, mode shapes and natural frequencies varied, and the results of the AMM and FEM differed; second, numerical calculation results showed three influencing factors on natural frequencies, namely, the lacing wire constant, the lacing wire location, and the flexible disk; lastly, the flexible disk could affect the stability of the system as reflected in the effect of the rotational speed.

  19. Excitation of kinetic Alfven waves by resonant mode conversion and longitudinal heating of magnetized plasmas

    Science.gov (United States)

    Tanaka, Motohiko; Sato, Tetsuya; Hasegawa, A.

    1989-01-01

    The excitation of the kinetic Alfven wave by resonant mode conversion and longitudinal heating of the plasma by the kinetic Alfven wave were demonstrated on the basis of a macroscale particle simulation. The longitudinal electron current was shown to be cancelled by the ions. The kinetic Alfven wave produced an ordered motion of the plasma particles in the wave propagation direction. The electrons were pushed forward along the ambient magnetic field by absorbing the kinetic Alfven wave through the Landau resonance.

  20. Analyzing the vibrational response of an AFM cantilever in liquid with the consideration of tip mass by comparing the hydrodynamic and contact repulsive force models in higher modes

    Science.gov (United States)

    Korayem, Moharam Habibnejad; Nahavandi, Amir

    2017-04-01

    This paper investigates the vibration of a tapping-mode Atomic Force Microscope (AFM) cantilever covered with two whole piezoelectric layers in a liquid medium. The authors of this article have already modeled the vibration of a cantilever immersed in liquid over rough surfaces. Five new ideas have been considered for improving the results of the previous work. Mass and damping of a cantilever probe tip have been considered. Since the probe tip of an AFM cantilever has a mass, which can itself affect the natural frequency of vibration, the significance of this mass has been explored. Also, two hydrodynamic force models for analyzing the mass and damping added to a cantilever in liquid medium have been evaluated. In modeling the vibration of a cantilever in liquid, simplifications are made to the theoretical equations used in the modeling, which may make the obtained results different from those in the real case. So, two hydrodynamic force models are introduced and compared with each other. In addition to the already introduced DMT model, the JKR model has been proposed. The forces acting on a probe tip have attractive and repulsive effects. The attractive Van der Waals force can vary depending on the surface smoothness or roughness, and the repulsive contact force, which is independent of the type of surface roughness and usually varies with the hardness or softness of a surface. When the first mode is used in the vibration of an AFM cantilever, the changes of the existing physical parameters in the simulation do not usually produce a significant difference in the response. Thus, three cantilever vibration modes have been investigated. Finally, an analytical approach for obtaining the response of equations is presented which solves the resulting motion equation by the Laplace method and, thus, a time function is obtained for cantilever deflection is determined. Also, using the COMSOL software to model a cantilever in a liquid medium, the computed natural

  1. Calculation of exact vibration modes for plane grillages by the dynamic stiffness method

    Science.gov (United States)

    Hallauer, W. L., Jr.; Liu, R. Y. L.

    1982-01-01

    A dynamic stiffness method is developed for the calculation of the exact modal parameters for plane grillages which consist of straight and uniform beams with coincident elastic and inertial axes. Elementary bending-torsion beam theory is utilized, and bending translation is restricted to one direction. The exact bending-torsion dynamic stiffness matrix is obtained for a straight and uniform beam element with coincident elastic and inertial axes. The element stiffness matrices are assembled using the standard procedure of the static stiffness method to form the dynamic stiffness matrix of the complete grillage. The exact natural frequencies, mode shapes, and generalized masses of the grillage are then calculated by solving a nonlinear eigenvalue problem based on the dynamic stiffness matrix. The exact modal solutions for an example grillage are calculated and compared with the approximate solutions obtained by using the finite element method.

  2. Impact of acoustic airflow on intrasinus drug deposition: New insights into the vibrating mode and the optimal acoustic frequency to enhance the delivery of nebulized antibiotic.

    Science.gov (United States)

    Leclerc, Lara; Merhie, Amira El; Navarro, Laurent; Prévôt, Nathalie; Durand, Marc; Pourchez, Jérémie

    2015-10-15

    We investigated the impact of vibrating acoustic airflow, the high frequency (f≥100 Hz) and the low frequency (f≤45 Hz) sound waves, on the enhancement of intrasinus drug deposition. (81m)Kr-gas ventilation study was performed in a plastinated human cast with and without the addition of vibrating acoustic airflow. Similarly, intrasinus drug deposition in a nasal replica using gentamicin as a marker was studied with and without the superposition of different modes of acoustic airflow. Ventilation experiments demonstrate that no sinus ventilation was observed without acoustic airflow although sinus ventilation occurred whatever the modes of acoustic airflow applied. Intrasinus drug deposition experiments showed that the high frequency acoustic airflow led to 4-fold increase in gentamicin deposition into the left maxillary sinus and to 2-fold deposition increase into the right maxillary sinus. Besides, the low frequency acoustic airflow demonstrated a significant increase of 4-fold and 2-fold in the right and left maxillary sinuses, respectively. We demonstrated the benefit of different modes of vibrating acoustic airflow for maxillary sinus ventilation and intrasinus drug deposition. The degree of gentamicin deposition varies as a function of frequency of the vibrating acoustic airflow and the geometry of the ostia. Copyright © 2015 Elsevier B.V. All rights reserved.

  3. Vibration control of a ship engine system using high-load magnetorheological mounts associated with a new indirect fuzzy sliding mode controller

    Science.gov (United States)

    Phu, Do Xuan; Choi, Seung-Bok

    2015-02-01

    In this work, a new high-load magnetorheological (MR) fluid mount system is devised and applied to control vibration in a ship engine. In the investigation of vibration-control performance, a new modified indirect fuzzy sliding mode controller is formulated and realized. The design of the proposed MR mount is based on the flow mode of MR fluid, and it includes two separated coils for generating a magnetic field. An optimization process is carried out to achieve maximal damping force under certain design constraints, such as the allowable height of the mount. As an actuating smart fluid, a new plate-like iron-particle-based MR fluid is used, instead of the conventional spherical iron-particle-based MR fluid. After evaluating the field-dependent yield stress of the MR fluid, the field-dependent damping force required to control unwanted vibration in the ship engine is determined. Subsequently, an appropriate-sized MR mount is manufactured and its damping characteristics are evaluated. After confirming the sufficient damping force level of the manufactured MR mount, a medium-sized ship engine mount system consisting of eight MR mounts is established, and its dynamic governing equations are derived. A new modified indirect fuzzy sliding mode controller is then formulated and applied to the engine mount system. The displacement and velocity responses show that the unwanted vibrations of the ship engine system can be effectively controlled in both the axial and radial directions by applying the proposed control methodology.

  4. On the intermolecular vibrational modes of the guanine⋯cytosine, adenine⋯thymine and formamide⋯formamide H-bonded dimers

    Science.gov (United States)

    Florián, Jan; Leszczynski, Jerzy; Johnson, Benny G.

    1995-04-01

    Harmonic force fields, frequencies, and IR and Raman intensities of the intermolecular vibrational modes in the cyclic formamide dimer and the guanine-cytosine and adenine-thymine DNA base pairs were calculated using several ab initio methods, including Hartree-Fock, MP2 and gradient-corrected density functional theory (DFT), with various basis sets. A polar environment was modeled using the polarizable continuum model (SCRF). The effect of electron correlation upon calculated Raman intensities was investigated using DFT. The normal coordinate analysis was carried out in internal coordinates observing C 2h symmetry of the formamide dimer. These coordinates were also generalized for the DNA base pairs, allowing force constants, frequencies and intensities of the characteristic intermolecular vibrational modes to be compared among the H-bonded complexes studied. In addition, coordinates defined in this way are directly related to standard DNA interbase structural parameters as pseudodyad, tilt and propeller twist angles. Extensive coupling of the intramolecular wagging vibrations of the amino groups participating in H-bonding with the tilt and propeller twist vibrations was obtained for the lowest frequency normal modes.

  5. Results of heating mode performance tests of a solar-assisted heat pump

    Science.gov (United States)

    Jones, C. B.; Smetana, F. O.

    1979-01-01

    The performance of a heat pump, utilizing 8.16 square meters of low-cost solar collectors as the evaporator in a Freon-114 refrigeration cycle, was determined under actual insolation conditions during the summer and fall of 1976. C.O.P.'s (coefficient of performance) greater than 3 were obtained with condensing temperatures around 78 C and evaporating temperatures around 27 C. Ambient temperatures were about 3 C above evaporating temperatures. Similar performance levels were obtained at other insolation and temperature conditions. Experience with the system has identified some component and system changes which should increase the obtainable C.O.P. to about 4.0. These are described along with the system's design rationale. The accumulated data are presented as an appendix.

  6. Blind identification of full-field vibration modes of output-only structures from uniformly-sampled, possibly temporally-aliased (sub-Nyquist), video measurements

    Science.gov (United States)

    Yang, Yongchao; Dorn, Charles; Mancini, Tyler; Talken, Zachary; Nagarajaiah, Satish; Kenyon, Garrett; Farrar, Charles; Mascareñas, David

    2017-03-01

    Enhancing the spatial and temporal resolution of vibration measurements and modal analysis could significantly benefit dynamic modelling, analysis, and health monitoring of structures. For example, spatially high-density mode shapes are critical for accurate vibration-based damage localization. In experimental or operational modal analysis, higher (frequency) modes, which may be outside the frequency range of the measurement, contain local structural features that can improve damage localization as well as the construction and updating of the modal-based dynamic model of the structure. In general, the resolution of vibration measurements can be increased by enhanced hardware. Traditional vibration measurement sensors such as accelerometers have high-frequency sampling capacity; however, they are discrete point-wise sensors only providing sparse, low spatial sensing resolution measurements, while dense deployment to achieve high spatial resolution is expensive and results in the mass-loading effect and modification of structure's surface. Non-contact measurement methods such as scanning laser vibrometers provide high spatial and temporal resolution sensing capacity; however, they make measurements sequentially that requires considerable acquisition time. As an alternative non-contact method, digital video cameras are relatively low-cost, agile, and provide high spatial resolution, simultaneous, measurements. Combined with vision based algorithms (e.g., image correlation or template matching, optical flow, etc.), video camera based measurements have been successfully used for experimental and operational vibration measurement and subsequent modal analysis. However, the sampling frequency of most affordable digital cameras is limited to 30-60 Hz, while high-speed cameras for higher frequency vibration measurements are extremely costly. This work develops a computational algorithm capable of performing vibration measurement at a uniform sampling frequency lower than

  7. Recent wind-driven change in Subantarctic Mode Water and its impact on ocean heat storage

    Science.gov (United States)

    Gao, Libao; Rintoul, Stephen R.; Yu, Weidong

    2018-01-01

    The subduction and export of Subantarctic Mode Water (SAMW) supplies the upper limb of the overturning circulation and makes an important contribution to global heat, freshwater, carbon and nutrient budgets1-5. Upper ocean heat content has increased since 2006, helping to explain the so-called global warming hiatus between 1998 and 2014, with much of the ocean warming concentrated in extratropical latitudes of the Southern Hemisphere in close association with SAMW and Antarctic Intermediate Water (AAIW)6,7. Here we use Argo observations to assess changes in the thickness, depth and heat content of the SAMW layer. Between 2005 and 2015, SAMW has thickened (3.6 ± 0.3 m yr-1), deepened (2.4 ± 0.2 m yr-1) and warmed (3.9 ± 0.3 W m-2). Wind forcing, rather than buoyancy forcing, is largely responsible for the observed trends in SAMW. Most (84%) of the increase in SAMW heat content is the result of changes in thickness; warming by buoyancy forcing (increased heat flux to the ocean) accounts for the remaining 16%. Projected increases in wind stress curl would drive further deepening of SAMW and increase in heat storage in the Southern Hemisphere oceans.

  8. Coordenadas cartesianas moleculares a partir da geometria dos modos normais de vibração Molecular cartesian coordinates from vibrational normal modes geometry

    Directory of Open Access Journals (Sweden)

    Emílio Borges

    2007-04-01

    Full Text Available A simple method to obtain molecular Cartesian coordinates as a function of vibrational normal modes is presented in this work. The method does not require the definition of special matrices, like the F and G of Wilson, neither of group theory. The Eckart's conditions together with the diagonalization of kinetic and potential energy are the only required expressions. This makes the present approach appropriate to be used as a preliminary study for more advanced concepts concerning vibrational analysis. Examples are given for diatomic and triatomic molecules.

  9. High Power Fast Wave Coupling and Heating in H-mode Plasmas on DIII-D

    Science.gov (United States)

    Pinsker, R. I.; Buttery, R. J.; Luce, T. C.; Porkolab, M.; Diem, S.; Kaufman, M.; Ryan, P. M.; Hosea, J. C.; Nagy, A.; Perkins, R.; Solomon, W. M.; Maggiora, R.; Milanesio, D.

    2012-10-01

    Up to 2.5 MW of fast wave (FW) heating power has been coupled to the core of ELMing H-mode discharges with βN<=2.5 in conjunction with 3-7 MW of neutral beam injection and 2.6 MW of electron cyclotron heating. Core FW heating efficiency has been found experimentally to approach 100% in the Advanced Inductive regime, consistent with the excellent absorption predicted by ray-tracing models in this high βe regime. Low antenna loading (high rf voltages) characteristic of such regimes makes increasing the FW power challenging. A study of techniques to enhance FW antenna loading has been carried out in DIII-D, with emphasis on maintenance of good confinement. The loading is in absolute agreement with modeling when edge density profiles measured with reflectometry are used in the model. Recent work extending the range of H-mode regimes to which FW heating has been applied and on increasing the FW power coupled to those regimes is described.

  10. Plasma heating due to X-B mode conversion in a cylindrical ECR plasma system

    Energy Technology Data Exchange (ETDEWEB)

    Yadav, V.K.; Bora, D. [Institute for Plasma Research, Bhat, Gandhinagar, Gujarat (India)

    2004-07-01

    Extra Ordinary (X) mode conversion to Bernstein wave near Upper Hybrid Resonance (UHR) layer plays an important role in plasma heating through cyclotron resonance. Wave generation at UHR and parametric decay at high power has been observed during Electron Cyclotron Resonance (ECR) heating experiments in toroidal magnetic fusion devices. A small linear system with ECR and UHR layer within the system has been used to conduct experiments on X-B conversion and parametric decay process as a function of system parameters. Direct probing in situ is conducted and plasma heating is evidenced by soft x-ray emission measurement. Experiments are performed with hydrogen plasma produced with 160-800 W microwave power at 2.45 GHz of operating frequency at 10{sup -3} mbar pressure. The axial magnetic field required for ECR is such that the resonant surface (B = 875 G) is situated at the geometrical axis of the plasma system. Experimental results will be presented in the paper. (authors)

  11. Experimental study on the performance of a simultaneous heating and cooling multi-heat pump with the variation of operation mode

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Hoon; Joo, Youngju; Chung, Hyunjoon; Kim, Yongchan [Department of Mechanical Engineering, Korea University, Anam-Dong, Sungbuk-Ku, Seoul 136-713 (Korea); Choi, Jongmin [Department of Mechanical Engineering, Hanbat National University, Duckmyung-Dong, Yusung-Ku, Daejeon 305-719 (Korea)

    2009-09-15

    The cooling load in the winter season becomes significant in commercial buildings and hotels because of the wide usage of office equipment and improved wall insulation. In this study, a simultaneous heating and cooling multi-heat pump having four indoor units and an outdoor unit was designed and tested in five operation modes: cooling-only, heating-only, cooling-main, heating-main, and entire heat recovery. The performance of the system with R410a was optimized by adjusting the system's control parameters. In the cooling-main mode, the rate of the bypass flow to the heating-operated indoor unit was optimized by controlling the EEV opening of the outdoor unit. In the heating-main mode, the mass flow rate to the cooling-operated indoor unit was optimized by adjusting the EEV opening in the outdoor unit. In the entire heat recovery mode, the compressor speed was controlled to improve the system COP with appropriate heating and cooling capacities. (author)

  12. Study of the thermal mode of a barn for piglets and a sow, created by combined heating system

    OpenAIRE

    Zhelykh, Vasyl; Dzeryn, Oleksandra; Shapoval, Stepan; Furdas, Yurij; Piznak, Bohdan

    2017-01-01

    The present research addresses solution to the relevant problem of energy efficient heating supply of pig farms with barns of pigs and a sow by applying combined heating systems based on local heating of places for animal keeping. A physical model is developed, which offered the possibility to carry out a complex of experimental studies on determining temperature mode in the barn for piglets and a sow. We established the patterns of influence of thermal capacity of individual heating devices,...

  13. A second, low-frequency mode of vibration in the intact mammalian cochlea

    Science.gov (United States)

    Lukashkin, Andrei N.; Russell, Ian J.

    2003-03-01

    The mammalian cochlea is a structure comprising a number of components connected by elastic elements. A mechanical system of this kind is expected to have multiple normal modes of oscillation and associated resonances. The guinea pig cochlear mechanics was probed using distortion components generated in the cochlea close to the place of overlap between two tones presented simultaneously. Otoacoustic emissions at frequencies of the distortion components were recorded in the ear canal. The phase behavior of the emissions reveals the presence of a nonlinear resonance at a frequency about a half octave below that of the high-frequency primary tone. The location of the resonance is level dependent and the resonance shifts to lower frequencies with increasing stimulus intensity. This resonance is thought to be associated with the tectorial membrane. The resonance tends to minimize input to the cochlear receptor cells at frequencies below the high-frequency primary and increases the dynamic load to the stereocilia of the receptor cells at the primary frequency when the tectorial membrane and reticular lamina move in counterphase.

  14. Research on the equivalent circuit model of a circular flexural-vibration-research on the equivalent circuit model of a circular flexural-vibration-mode piezoelectric transformer with moderate thickness.

    Science.gov (United States)

    Huang, Yihua; Huang, Wenjin; Wang, Qinglei; Su, Xujian

    2013-07-01

    The equivalent circuit model of a piezoelectric transformer is useful in designing and optimizing the related driving circuits. Based on previous work, an equivalent circuit model for a circular flexural-vibration-mode piezoelectric transformer with moderate thickness is proposed and validated by finite element analysis. The input impedance, voltage gain, and efficiency of the transformer are determined through computation. The basic behaviors of the transformer are shown by numerical results.

  15. Influence of curvature strain and Van der Waals force on the inter-layer vibration mode of WS2 nanotubes: A confocal micro-Raman spectroscopic study

    Science.gov (United States)

    Wang, Xiao Hu; Zheng, Chang Cheng; Ning, Ji Qiang

    2016-01-01

    Transition-metal dichalcogenides (TMDs) nanostructures including nanotubes and monolayers have attracted great interests in materials science, chemistry to condensed matter physics. We present an interesting study of the vibration modes in multi-walled tungsten sulfide (WS2) nanotubes prepared via sulfurizing tungsten oxide (WO3) nanowires which are investigated by confocal micro-Raman spectroscopy. The inter-layer vibration mode of WS2 nanotubes, A1g, is found to be sensitive to the diameter and curvature strain, while the in-plane vibration mode, E12g, is not. A1g mode frequency shows a redshift by 2.5 cm−1 for the multi-layered nanotubes with small outer-diameters, which is an outcome of the competition between the Van der Waals force stiffening and the curvature strain softening. We also show that the Raman peak intensity ratio is significantly different between the 1–2 wall layered nanotubes and monolayer flat sheets. PMID:27620879

  16. Efforts toward developing probes of protein dynamics: vibrational dephasing and relaxation of carbon-deuterium stretching modes in deuterated leucine.

    Science.gov (United States)

    Zimmermann, Jörg; Gundogdu, Kenan; Cremeens, Matthew E; Bandaria, Jigar N; Hwang, Gil Tae; Thielges, Megan C; Cheatum, Christopher M; Romesberg, Floyd E

    2009-06-11

    The spectral position of C-D stretching absorptions in the so-called "transparent window" of protein absorption (1800-2300 cm(-1)) makes them well suited as probes of protein dynamics with high temporal and structural resolution. We have previously incorporated single deuterated amino acids into proteins to site-selectively follow protein folding and ligand binding by steady-state FT IR spectroscopy. Ultimately, our goal is to use C-D bonds as probes in time-resolved IR spectroscopy to study dynamics and intramolecular vibrational energy redistribution (IVR) in proteins. As a step toward this goal, we now present the first time-resolved experiments characterizing the population and dephasing dynamics of selectively excited C-D bonds in a deuterated amino acid. Three differently deuterated, Boc-protected leucines were selected to systematically alter the number of additional C-D bonds that may mediate IVR out of the initially populated bright C-D stretching mode. Three-pulse photon echo experiments show that the steady-state C-D absorption linewidths are broadened by both homogeneous and inhomogeneous effects, and transient grating experiments reveal that IVR occurs on a subpicosecond time scale and is nonstatistical. The results have important implications for the interpretation of steady-state C-D spectra and demonstrate the potential utility of C-D bonds as probes of dynamics and IVR within a protein.

  17. Flexible Helicoids, Atomic Force Microscopy (AFM Cantilevers in High Mode Vibration, and Concave Notch Hinges in Precision Measurements and Research

    Directory of Open Access Journals (Sweden)

    Yakov Tseytlin

    2012-05-01

    Full Text Available Flexible structures are the main components in many precision measuring and research systems. They provide miniaturization, repeatability, minimal damping, low measuring forces, and very high resolution. This article focuses on the modeling, development, and comparison of three typical flexible micro- nano-structures: flexible helicoids, atomic force microscopy (AFM cantilevers, and concave notch hinges. Our theory yields results which allow us to increase the accuracy and functionality of these structures in new fields of application such as the modeling of helicoidal DNA molecules’ mechanics, the definition of instantaneous center of rotation in concave flexure notch hinges, and the estimation of the increase of spring constants and resolution at higher mode vibration in AFM cantilevers with an additional concentrated and end extended mass. We developed the original kinetostatic, reverse conformal mapping of approximating contours, and non-linear thermomechanical fluctuation methods for calculation, comparison, and research of the micromechanical structures. These methods simplify complicated solutions in micro elasticity but provide them with necessary accuracy. All our calculation results in this article and in all corresponding referenced author’s publications are in a good agreement with experimental and finite element modeling data within 10% or less.

  18. Electron heating via mode converted ion Bernstein waves in the Alcator C-Mod tokamak

    Energy Technology Data Exchange (ETDEWEB)

    Bonoli, P.T.; OShea, P.; Brambilla, M.; Golovato, S.N.; Hubbard, A.E.; Porkolab, M.; Takase, Y.; Boivin, R.L.; Bombarda, F.; Christensen, C.; Fiore, C.L.; Garnier, D.; Goetz, J.; Granetz, R.; Greenwald, M.; Horne, S.F.; Hutchinson, I.H.; Irby, J.; Jablonski, D.; LaBombard, B.; Lipschultz, B.; Marmar, E.; May, M.; Mazurenko, A.; McCracken, G.; Nachtrieb, R.; Niemczewski, A.; Ohkawa, H.; Pappas, D.A.; Reardon, J.; Rice, J.; Rost, C.; Schachter, J.; Snipes, J.A.; Stek, P.; Takase, K.; Terry, J.; Wang, Y.; Watterson, R.L.; Welch, B.; Wolfe, S.M. [Plasma Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

    1997-05-01

    Highly localized direct electron heating [full width at half-maximum (FWHM){congruent}0.2a] via mode converted ion Bernstein waves has been observed in the Alcator C-Mod Tokamak [I. H. Hutchinson {ital et al.}, Phys. Plasmas {bold 1}, 1511 (1994)]. Electron heating at or near the plasma center (r/a{ge}0.3) has been observed in H({sup 3}He) discharges at B{sub 0}=(6.0{endash}6.5)T and n{sub e}(0){congruent}1.8{times}10{sup 20}m{sup {minus}3}. [Here, the minority ion species is indicated parenthetically.] Off-axis heating (r/a{ge}0.5) has also been observed in D({sup 3}He) plasmas at B{sub 0}=7.9T. The concentration of {sup 3}He in these experiments was in the range of n{sub 3{sub He}}/n{sub e}{congruent}(0.2{endash}0.3) and the locations of the mode conversion layer and electron heating peak could be controlled by changing the {sup 3}He concentration or toroidal magnetic field (B{sub 0}). The electron heating profiles were deduced using a rf modulation technique. Detailed comparisons with one-dimensional and toroidal full-wave models in the ion cyclotron range of frequencies have been carried out. One-dimensional full-wave code predictions were found to be in qualitative agreement with the experimental results. Toroidal full-wave calculations indicated the importance of volumetric and wave focusing effects in the interpretation of the experimental results. {copyright} {ital 1997 American Institute of Physics.}

  19. Unsteady Heat-Flux Measurements of Second-Mode Instability Waves in a Hypersonic Boundary Layer

    Science.gov (United States)

    Kergerise, Michael A.; Rufer, Shann J.

    2016-01-01

    In this paper we report on the application of the atomic layer thermopile (ALTP) heat- flux sensor to the measurement of laminar-to-turbulent transition in a hypersonic flat plate boundary layer. The centerline of the flat-plate model was instrumented with a streamwise array of ALTP sensors and the flat-plate model was exposed to a Mach 6 freestream over a range of unit Reynolds numbers. Here, we observed an unstable band of frequencies that are associated with second-mode instability waves in the laminar boundary layer that forms on the flat-plate surface. The measured frequencies, group velocities, phase speeds, and wavelengths of these instability waves are in agreement with data previously reported in the literature. Heat flux time series, and the Morlet-wavelet transforms of them, revealed the wave-packet nature of the second-mode instability waves. In addition, a laser-based radiative heating system was developed to measure the frequency response functions (FRF) of the ALTP sensors used in the wind tunnel test. These measurements were used to assess the stability of the sensor FRFs over time and to correct spectral estimates for any attenuation caused by the finite sensor bandwidth.

  20. Automation and heat transfer characterization of immersion mode spectroscopy for analysis of ice nucleating particles

    Science.gov (United States)

    Beall, Charlotte M.; Stokes, M. Dale; Hill, Thomas C.; DeMott, Paul J.; DeWald, Jesse T.; Prather, Kimberly A.

    2017-07-01

    Ice nucleating particles (INPs) influence cloud properties and can affect the overall precipitation efficiency. Developing a parameterization of INPs in global climate models has proven challenging. More INP measurements - including studies of their spatial distribution, sources and sinks, and fundamental freezing mechanisms - must be conducted in order to further improve INP parameterizations. In this paper, an immersion mode INP measurement technique is modified and automated using a software-controlled, real-time image stream designed to leverage optical changes of water droplets to detect freezing events. For the first time, heat transfer properties of the INP measurement technique are characterized using a finite-element-analysis-based heat transfer simulation to improve accuracy of INP freezing temperature measurement. The heat transfer simulation is proposed as a tool that could be used to explain the sources of bias in temperature measurements in INP measurement techniques and ultimately explain the observed discrepancies in measured INP freezing temperatures between different instruments. The simulation results show that a difference of +8.4 °C between the well base temperature and the headspace gas results in an up to 0.6 °C stratification of the aliquot, whereas a difference of +4.2 °C or less results in a thermally homogenous water volume within the error of the thermal probe, ±0.2 °C. The results also show that there is a strong temperature gradient in the immediate vicinity of the aliquot, such that without careful placement of temperature probes, or characterization of heat transfer properties of the water and cooling environment, INP measurements can be biased toward colder temperatures. Based on a modified immersion mode technique, the Automated Ice Spectrometer (AIS), measurements of the standard test dust illite NX are reported and compared against six other immersion mode droplet assay techniques featured in Hiranuma et al. (2015) that used

  1. Effects of heat exchange and nonlinearity on acoustic streaming in a vibrating cylindrical cavity.

    Science.gov (United States)

    Gubaidullin, Amir A; Yakovenko, Anna V

    2015-06-01

    Acoustic streaming in a gas filled cylindrical cavity subjected to the vibration effect is investigated numerically. Both thermally insulated walls and constant temperature walls are considered. The range of vibration frequencies from low frequencies, at which the process can be described by an approximate analytical solution, to high frequencies giving rise to strong nonlinear effects is studied. Frequencies lower than the resonant one are chosen, and nonlinearity is achieved due to the large amplitude. The problem is solved in an axisymmetric statement. The dependence of acoustic streaming in narrow channels at vibration frequencies lower than the resonant one on the type of thermal boundary conditions is shown. The streaming vortices' directions of rotation in the case of constant temperature walls are found to be opposite to those in the case of thermally insulated walls. Different nonlinear effects, which increase with the frequency of vibration, are obtained. Nonlinear effects manifesting as the nonuniformity of average temperature, pressure, and density are in turn found to be influencing the streaming velocity and streaming structure.

  2. Mode conversion electron heating in Alcator C-Mod: Theory and experiment

    Energy Technology Data Exchange (ETDEWEB)

    Bonoli, P. T. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Brambilla, M. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Nelson-Melby, E. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Phillips, C. K. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Porkolab, M. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Schilling, G. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Taylor, G. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Wukitch, S. J. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Boivin, R. L. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Boswell, C. J. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)] (and others)

    2000-05-01

    Localized electron heating [full width at half maximum of {delta}(r/a){approx_equal}0.2] by mode converted ion Bernstein waves (IBW) has been observed in the Alcator C-Mod tokamak [I. H. Hutchinson et al., Phys. Plasmas 1, 1511 (1994)]. These experiments were performed in D({sup 3}He) plasmas at high magnetic field (B{sub 0}=7.9 T), high-plasma density (n{sub e0}{>=}1.5x10{sup 20} m{sup -3}), and for 0.05{<=}n{sub He-3}/n{sub e}{<=}0.30. Electron heating profiles of the mode converted IBW were measured using a break in slope analysis of the electron temperature versus time in the presence of rf (radio frequency) modulation. The peak position of electron heating was found to be well-correlated with {sup 3}He concentration, in agreement with the predictions of cold plasma theory. Recently, a toroidal full-wave ion cyclotron range of frequencies (ICRF) code TORIC [M. Brambilla, Nucl. Fusion 38, 1805 (1998)] was modified to include the effects of IBW electron Landau damping at (k{sub (perpendicular} {sub sign)}{rho}{sub i}){sup 2}>>1, This model was used in combination with a 1D (one-dimensional) integral wave equation code METS [D. N. Smithe et al., Radio Frequency Power in Plasmas, AIP Conf. Proc. 403 (1997), p. 367] to analyze these experiments. Model predictions were found to be in qualitative and in some instances quantitative agreement with experimental measurements. A model for mode conversion current drive (MCCD) has also been developed which combines a toroidal full wave code with an adjoint evaluation of the ICRF current drive efficiency. Predictions for off-axis MCCD in C-Mod have been made using this model and will be described. (c) 2000 American Institute of Physics.

  3. Effect of variable heat treatment modes on microstructures of Fe-Cr-B cast iron alloy

    Directory of Open Access Journals (Sweden)

    Guo Changqing

    2008-02-01

    Full Text Available The effect of heat treatment mode on the microstructure of Fe-Cr-B cast iron alloys was investigated in this paper by comparing the difference of precipitation patterns of secondary particles after thermal cycling treatment (TCT with those after normal heat treatment (NHT. No obvious differences were found in precipitation patterns of secondary particles between TCT and NHT when experimental temperature was below Ar1. However, when temperature was over Ar1, there were significant differences, with secondary particles prominently segregated at the grain boundaries under TCT, while the particles evenly distributed in the matrix under NHT. The reason for the microstructure differences could be associated with the development of non-equilibrium segregation of boron during TCT.

  4. Non-local heat transport in Alcator C-Mod ohmic L-mode plasmas

    Science.gov (United States)

    Gao, C.; Rice, J. E.; Sun, H. J.; Reinke, M. L.; Howard, N. T.; Mikkelson, D.; Hubbard, A. E.; Chilenski, M. A.; Walk, J. R.; Hughes, J. W.; Ennever, P. C.; Porkolab, M.; White, A. E.; Sung, C.; Delgado-Aparicio, L.; Baek, S. G.; Rowan, W. L.; Brookman, M. W.; Greenwald, M. J.; Granetz, R. S.; Wolfe, S. W.; Marmar, E. S.; The Alcator C-Mod Team

    2014-08-01

    Non-local heat transport experiments were performed in Alcator C-Mod ohmic L-mode plasmas by inducing edge cooling with laser blow-off impurity (CaF2) injection. The non-local effect, a cooling of the edge electron temperature with a rapid rise of the central electron temperature, which contradicts the assumption of ‘local’ transport, was observed in low collisionality linear ohmic confinement (LOC) regime plasmas. Transport analysis shows this phenomenon can be explained either by a fast drop of the core diffusivity, or the sudden appearance of a heat pinch. In high collisionality saturated ohmic confinement (SOC) regime plasmas, the thermal transport becomes ‘local’: the central electron temperature drops on the energy confinement time scale in response to the edge cooling. Measurements from a high resolution imaging x-ray spectrometer show that the ion temperature has a similar behaviour as the electron temperature in response to edge cooling, and that the transition density of non-locality correlates with the rotation reversal critical density. This connection may indicate the possible connection between thermal and momentum transport, which is also linked to a transition in turbulence dominance between trapped electron modes (TEMs) and ion temperature gradient (ITG) modes. Experiments with repetitive cold pulses in one discharge were also performed to allow Fourier analysis and to provide details of cold front propagation. These modulation experiments showed in LOC plasmas that the electron thermal transport is not purely diffusive, while in SOC the electron thermal transport is more diffusive like. Linear gyrokinetic simulations suggest the turbulence outside r/a = 0.75 changes from TEM dominance in LOC plasmas to ITG mode dominance in SOC plasmas.

  5. The optimization of single mode basis functions for polyatomic vibrational problems with application to the water molecule

    Science.gov (United States)

    Schwenke, David W.

    1992-01-01

    The optimization of the wave functions is considered for coupled vibrations represented by linear combinations of products of functions depending only on a single vibrational coordinate. The functions themselves are optimized as well as configuration list. For the H2O molecule highly accurate results are obtained for the lowest 15 levels using significantly shorter expansions than would otherwise be possible.

  6. Vibrational Spectroscopy of the CCl[subscript 4] v[subscript 1] Mode: Theoretical Prediction of Isotopic Effects

    Science.gov (United States)

    Gaynor, James D.; Wetterer, Anna M.; Cochran, Rea M.; Valente, Edward J.; Mayer, Steven G.

    2015-01-01

    Raman spectroscopy is a powerful experimental technique, yet it is often missing from the undergraduate physical chemistry laboratory curriculum. Tetrachloromethane (CCl[subscript 4]) is the ideal molecule for an introductory vibrational spectroscopy experiment and the symmetric stretch vibration contains fine structure due to isotopic variations…

  7. Thermal Buckling and Free Vibration Analysis of Heated Functionally Graded Material Beams

    OpenAIRE

    Khalane Sanjay Anandrao; R. K. Gupta; P. Ramachandran; G. V. Rao

    2013-01-01

    The effect of temperature dependency of material properties on thermal buckling and free vibration of functionally graded material (FGM) beams is studied. The FGM beam is assumed to be at a uniform through thickness temperature, above the ambient temperature. Finite element system of equations based on the first order shear deformation theory is developed. FGM beam with axially immovable ends having the classical boundary conditions is analysed. An exhaustive set of numerical results, in term...

  8. Vibration mode shapes visualization in industrial environment by real-time time-averaged phase-stepped electronic speckle pattern interferometry at 10.6 μm and shearography at 532 nm

    Science.gov (United States)

    Languy, Fabian; Vandenrijt, Jean-François; Thizy, Cédric; Rochet, Jonathan; Loffet, Christophe; Simon, Daniel; Georges, Marc P.

    2016-12-01

    We present our investigations on two interferometric methods suitable for industrial conditions dedicated to the visualization of vibration modes of aeronautic blades. First, we consider long-wave infrared (LWIR) electronic speckle pattern interferometry (ESPI). The use of long wavelength allows measuring larger amplitudes of vibrations compared with what can be achieved with visible light. Also longer wavelengths allow lower sensitivity to external perturbations. Second, shearography at 532 nm is used as an alternative to LWIR ESPI. Both methods are used in time-averaged mode with the use of phase-stepping. This allows transforming Bessel fringes, typical to time averaging, into phase values that provide higher contrast and improve the visualization of vibration mode shapes. Laboratory experimental results with both techniques allowed comparison of techniques, leading to selection of shearography. Finally a vibration test on electrodynamic shaker is performed in an industrial environment and mode shapes are obtained with good quality by shearography.

  9. Heat Transfer Measurements with Surface Mounted Foil-Sensors in an Active Mode: A Comprehensive Review and a New Design

    OpenAIRE

    Mocikat, Horst; Herwig, Heinz

    2009-01-01

    A comprehensive review of film-sensors shows that they are primarily operated in a passive mode, i.e. without being actively heated to an extent, whereby they create a heat transfer situation on their own. Only when these sensors are used for wall shear stress measurements, the detection of laminar/turbulent transition, or the measurement of certain flow velocities, they are operated in an active mode, i.e. heated by an electrical current (after an appropriate calibration). In our study we de...

  10. Heat transfer measurements with surface mounted foil-sensors in an active mode: a comprehensive review and a new design.

    Science.gov (United States)

    Mocikat, Horst; Herwig, Heinz

    2009-01-01

    A comprehensive review of film-sensors shows that they are primarily operated in a passive mode, i.e. without being actively heated to an extent, whereby they create a heat transfer situation on their own. Only when these sensors are used for wall shear stress measurements, the detection of laminar/turbulent transition, or the measurement of certain flow velocities, they are operated in an active mode, i.e. heated by an electrical current (after an appropriate calibration). In our study we demonstrate how these R(T)-based sensors (temperature dependence of the electrical resistance R) can also be applied in an active mode for heat transfer measurements. These measurements can be made on cold, unheated bodies, provided certain requirements with respect to the flow field are fulfilled. Our new sensors are laminated nickel- and polyimide-foils manufactured with a special technology, which is also described in detail.

  11. Heat Transfer Measurements with Surface Mounted Foil-Sensors in an Active Mode: A Comprehensive Review and a New Design

    Directory of Open Access Journals (Sweden)

    Heinz Herwig

    2009-04-01

    Full Text Available A comprehensive review of film-sensors shows that they are primarily operated in a passive mode, i.e. without being actively heated to an extent, whereby they create a heat transfer situation on their own. Only when these sensors are used for wall shear stress measurements, the detection of laminar/turbulent transition, or the measurement of certain flow velocities, they are operated in an active mode, i.e. heated by an electrical current (after an appropriate calibration. In our study we demonstrate how these R(T-based sensors (temperature dependence of the electrical resistance R can also be applied in an active mode for heat transfer measurements. These measurements can be made on cold, unheated bodies, provided certain requirements with respect to the flow field are fulfilled. Our new sensors are laminated nickel- and polyimide-foils manufactured with a special technology, which is also described in detail.

  12. New Method to Study the Vibrational Modes of Biomolecules in the Terahertz Range Based on a Single-Stage Raman Spectrometer.

    Science.gov (United States)

    Kalanoor, Basanth S; Ronen, Maria; Oren, Ziv; Gerber, Doron; Tischler, Yaakov R

    2017-03-31

    The low-frequency vibrational (LFV) modes of biomolecules reflect specific intramolecular and intermolecular thermally induced fluctuations that are driven by external perturbations, such as ligand binding, protein interaction, electron transfer, and enzymatic activity. Large efforts have been invested over the years to develop methods to access the LFV modes due to their importance in the studies of the mechanisms and biological functions of biomolecules. Here, we present a method to measure the LFV modes of biomolecules based on Raman spectroscopy that combines volume holographic filters with a single-stage spectrometer, to obtain high signal-to-noise-ratio spectra in short acquisition times. We show that this method enables LFV mode characterization of biomolecules even in a hydrated environment. The measured spectra exhibit distinct features originating from intra- and/or intermolecular collective motion and lattice modes. The observed modes are highly sensitive to the overall structure, size, long-range order, and configuration of the molecules, as well as to their environment. Thus, the LFV Raman spectrum acts as a fingerprint of the molecular structure and conformational state of a biomolecule. The comprehensive method we present here is widely applicable, thus enabling high-throughput study of LFV modes of biomolecules.

  13. Gyrokinetic simulations of momentum transport and fluctuation spectra for ICRF-heated L-Mode plasmas

    Science.gov (United States)

    Sierchio, J. M.; White, A. E.; Howard, N. T.; Sung, C.; Ennever, P.; Porkolab, M.; Candy, J.

    2014-10-01

    We examine ICRF-heated L-mode plasmas in Alcator C-Mod, with differing momentum transport (hollow vs. peaked radial profiles of intrinsic toroidal rotation) but similar heat and particle transport. Nonlinear gyrokinetic simulations of heat and particle transport with GYRO [Candy and Waltz, J. Comp. Phys. 186, 545 (2003)] have previously been compared with these experiments [White et al., Phys. Plasmas 20, 056106 (2013); Howard et al. PPCF submitted (2014)] as part of an effort to validate the gyrokinetic model for core turbulent transport in C-Mod plasmas. To further test the model for these plasmas, predicted core turbulence characteristics such as fluctuation spectra will be compared with experiment. Using synthetic diagnostics for the CECE, reflectometry, and PCI systems at C-Mod, synthetic spectra and, when applicable, fluctuation amplitudes, are generated. We compare these generated results with fluctuation measurements from the experiment. We also report the momentum transport results from simulations of these plasmas and compare them to experiment. Supported by USDoE award DE-FC02-99ER54512.

  14. Particle and heat flux estimates in Proto-MPEX in Helicon Mode with IR imaging

    Science.gov (United States)

    Showers, M. A.; Biewer, T. M.; Caughman, J. B. O.; Donovan, D. C.; Goulding, R. H.; Rapp, J.

    2016-10-01

    The Prototype Material Plasma Exposure eXperiment (Proto-MPEX) at Oak Ridge National Laboratory (ORNL) is a linear plasma device developing the plasma source concept for the Material Plasma Exposure eXperiment (MPEX), which will address plasma material interaction (PMI) science for future fusion reactors. To better understand how and where energy is being lost from the Proto-MPEX plasma during ``helicon mode'' operations, particle and heat fluxes are quantified at multiple locations along the machine length. Relevant diagnostics include infrared (IR) cameras, four double Langmuir probes (LPs), and in-vessel thermocouples (TCs). The IR cameras provide temperature measurements of Proto-MPEX's plasma-facing dump and target plates, located on either end of the machine. The change in surface temperature is measured over the duration of the plasma shot to determine the heat flux hitting the plates. The IR cameras additionally provide 2-D thermal load distribution images of these plates, highlighting Proto-MPEX plasma behaviors, such as hot spots. The LPs and TCs provide additional plasma measurements required to determine particle and heat fluxes. Quantifying axial variations in fluxes will help identify machine operating parameters that will improve Proto-MPEX's performance, increasing its PMI research capabilities. This work was supported by the U.S. D.O.E. contract DE-AC05-00OR22725.

  15. Phase change based cooling for high burst mode heat loads with temperature regulation above the phase change temperature

    Science.gov (United States)

    The United States of America as represented by the United States Department of Energy

    2009-12-15

    An apparatus and method for transferring thermal energy from a heat load is disclosed. In particular, use of a phase change material and specific flow designs enables cooling with temperature regulation well above the fusion temperature of the phase change material for medium and high heat loads from devices operated intermittently (in burst mode). Exemplary heat loads include burst mode lasers and laser diodes, flight avionics, and high power space instruments. Thermal energy is transferred from the heat load to liquid phase change material from a phase change material reservoir. The liquid phase change material is split into two flows. Thermal energy is transferred from the first flow via a phase change material heat sink. The second flow bypasses the phase change material heat sink and joins with liquid phase change material exiting from the phase change material heat sink. The combined liquid phase change material is returned to the liquid phase change material reservoir. The ratio of bypass flow to flow into the phase change material heat sink can be varied to adjust the temperature of the liquid phase change material returned to the liquid phase change material reservoir. Varying the flowrate and temperature of the liquid phase change material presented to the heat load determines the magnitude of thermal energy transferred from the heat load.

  16. Influence of surface micro-beams with large deflection on the resonance frequency of a quartz crystal resonator in thickness-shear mode vibrations

    Directory of Open Access Journals (Sweden)

    Chi Luo

    2017-03-01

    Full Text Available We study the dynamic behavior of a quartz crystal resonator (QCR in thickness-shear vibrations with the upper surface covered by an array of micro-beams (MBs under large deflection. Through taking into account the continuous conditions of shear force and bending moment at the interface of MBs/resonator, dependences of frequency shift of the compound QCR system versus material parameter and geometrical parameter are illustrated in detail for nonlinear and linear vibrations. It is found that the frequency shift produces a little right (left translation for increasing elastic modulus (length/radius ratio of MBs. Moreover, the frequency right (left translation distance caused by nonlinear deformation becomes more serious in the second-order mode than in the first-order one.

  17. Direct evidence for mode-specific vibrational energy relaxation from quantum time-dependent perturbation theory. III. The nu(4) and nu(7) modes of nonplanar nickel porphyrin models.

    Science.gov (United States)

    Zhang, Yong; Straub, John E

    2009-06-07

    The time scales and pathways of vibrational energy relaxation (VER) of the nu(4) and nu(7) modes of three nickel porphyrin models, nickel porphine (NiP), nickel protoporphyrin IX (Ni-heme), and nickel octaethylporphyrin (NiOEP), were studied using a non-Markovian time-dependent perturbation theory at the B3LYP/6-31G(d) level. When NiP is calculated with D(4h) symmetry, it has the planar structure and the same VER properties as ferrous iron porphine (FeP). The porphine cores of both Ni-heme and NiOEP were distorted from a planar geometry, assuming a nonplanar structure, similar to that of the heme structure in cytochrome c. The VER time scales of Ni-heme are found to be similar to those predicted for a planar iron heme, but the derived pathways have distinctly different features. In particular, the strong coupling between the nu(7) mode and the overtone of the approximately 350 cm(-1) gamma(7) mode, observed for planar porphyrins, is absent in both nonplanar nickel porphyrins. Direct energy exchange between the nu(4) and nu(7) modes is not observed in NiOEP, but is found to play an essential role in the VER of the nu(4) mode in Ni-heme. The Ni-heme isopropionate groups are involved in the dominant VER pathways of both the nu(4) and nu(7) modes of Ni-heme. However, in contrast with VER pathways derived in planar iron heme, the isopropionate groups are not observed to play an essential role relative to other side chains in spatially directing the vibrational energy flow.

  18. Stress-anneal-induced magnetic anisotropy in highly textured Fe-Ga and Fe-Al magnetostrictive strips for bending-mode vibrational energy harvesters

    Directory of Open Access Journals (Sweden)

    Jung Jin Park

    2016-05-01

    Full Text Available Magnetostrictive Fe-Ga and Fe-Al alloys are promising materials for use in bending-mode vibrational energy harvesters. For this study, 50.8 mm × 5.0 mm × 0.5 mm strips of Fe-Ga and Fe-Al were cut from 0.50-mm thick rolled sheet. An atmospheric anneal was used to develop a Goss texture through an abnormal grain growth process. The anneal lead to large (011 grains that covered over 90% of sample surface area. The resulting highly-textured Fe-Ga and Fe-Al strips exhibited saturation magnetostriction values (λsat =  λ∥ − λ⊥ of ∼280 ppm and ∼130 ppm, respectively. To maximize 90° rotation of magnetic moments during bending of the strips, we employed compressive stress annealing (SA. Samples were heated to 500°C, and a 100-150 MPa compressive stress was applied while at 500°C for 30 minutes and while being cooled. The effectiveness of the SA on magnetic moment rotation was inferred by comparing post-SA magnetostriction with the maximum possible yield of rotated magnetic moments, which is achieved when λ∥ = λsat and λ⊥ = 0. The uniformity of the SA along the sample length and the impact of the SA on sensing/energy harvesting performance were then assessed by comparing pre- and post-SA bending-stress-induced changes in magnetization at five different locations along the samples. The SA process with a 150 MPa compressive load improved Fe-Ga actuation along the sample length from 170 to 225 ppm (from ∼60% to within ∼80% of λsat. The corresponding sensing/energy harvesting performance improved by as much as a factor of eight in the best sample, however the improvement was not at all uniform along the sample length. The SA process with a 100 MPa compressive load improved Fe-Al actuation along the sample length from 60 to 73 ppm (from ∼46% to ∼56% of λsat, indicating only a marginally effective SA and suggesting the need for modification of the SA protocol. In spite of this, the SA was effective at improving the sensing

  19. Modification of argon impurity transport by electron cyclotron heating in KSTAR H-mode plasmas

    Science.gov (United States)

    Hong, Joohwan; Henderson, S. S.; Kim, Kimin; Seon, C. R.; Song, Inwoo; Lee, H. Y.; Jang, Juhyeok; Park, Jae Sun; Lee, S. G.; Lee, J. H.; Lee, Seung Hun; Hong, Suk-Ho; Choe, Wonho

    2017-03-01

    Experiments with a small amount of Ar gas injection as a trace impurity were conducted in the Korea Superconducting Tokamak Advanced Research (KSTAR) H-mode plasma ({{B}\\text{T}}   =  2.8 T, {{I}\\text{P}}   =  0.6 MA, and {{P}\\text{NBI}}   =  4.0 MW). 170 GHz electron cyclotron resonance heating (ECH) at 600 and 800 kW was focused along the mid-plane with a fixed major radial position of R   =  1.66 m. The emissivity of the Ar16+ (3.949 {\\mathring{\\text{A}}} ) and Ar15+ (353.860 {\\mathring{\\text{A}}} ) spectral lines were measured by x-ray imaging crystal spectroscopy (XICS) and a vacuum UV (VUV) spectrometer, respectively. ECH reduces the peak Ar15+ emission and increases the Ar16+ emission, an effect largest with 800 kW. The ADAS-SANCO impurity transport code was used to evaluate the Ar transport coefficients. It was found that the inward convective velocity found in the plasma core without ECH was decreased with ECH, while diffusion remained approximately constant resulting in a less-peaked Ar density profile. Theoretical results from the NEO code suggest that neoclassical transport is not responsible for the change in transport, while the microstability analysis using GKW predicts a dominant ITG mode during both ECH and non-ECH plasmas.

  20. Recovery of oxygenated ignitable liquids by zeolites, Part II: Dual-mode heated passive headspace extraction.

    Science.gov (United States)

    Rodgers, Corissa L; St Pierre, Kathryne A; Hall, Adam B

    2014-07-01

    Previous studies performed by our research group have suggested that zeolites are a suitable adsorbent for the recovery of oxygenates from fire debris through heated passive headspace extraction. Zeolite 13X, in particular, has been shown to be effective for recovering analytes with molecular diameters smaller than 10Å. The primary aim of this study was to evaluate the addition of zeolite 13X to heated headspace extraction for the recovery of ignitable liquids. Comparative recoveries of petroleum and alcohol-based ignitable liquid mixtures were studied utilizing activated charcoal strips and zeolites, individually and in tandem. In the presence of both adsorption media within the same sample can, activated charcoal strips recovered the majority of gasoline components, while zeolites recovered the majority of oxygenated compounds. This phenomenon was attributed to the size exclusion properties, polarity, and available surface area of zeolites. This research supports the use of zeolites with activated charcoal strips in a "dual-mode" preparation for casework in which the presence of an ignitable liquid is suspected. The described method allows for the recovery and concentration of ignitable liquid residues in a single extraction procedure, whether the ignitable liquid is petroleum-based or oxygenated in nature. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  1. Spline-based Rayleigh-Ritz methods for the approximation of the natural modes of vibration for flexible beams with tip bodies

    Science.gov (United States)

    Rosen, I. G.

    1986-01-01

    Rayleigh-Ritz methods for the approximation of the natural modes for a class of vibration problems involving flexible beams with tip bodies using subspaces of piecewise polynomial spline functions are developed. An abstract operator-theoretic formulation of the eigenvalue problem is derived and spectral properties investigated. The existing theory for spline-based Rayleigh-Ritz methods applied to elliptic differential operators and the approximation properties of interpolatory splines are used to argue convergence and establish rates of convergence. An example and numerical results are discussed.

  2. Robust vibration control at critical resonant modes using indirect-driven self-sensing actuation in mechatronic systems.

    Science.gov (United States)

    Hong, Fan; Pang, Chee Khiang

    2012-11-01

    This paper presents an improved indirect-driven self-sensing actuation circuit for robust vibration control of piezoelectrically-actuated flexible structures in mechatronic systems. The circuit acts as a high-pass filter and provides better self-sensing strain signals with wider sensing bandwidth and higher signal-to-noise ratio. An adaptive non-model-based control is used to compensate for the structural vibrations using the strain signals from the circuit. The proposed scheme is implemented in a PZT-actuated suspension of a commercial dual-stage hard disk drive. Experimental results show improvements of 50% and 75% in the vibration suppression at 5.4kHz and 21kHz respectively, compared to the conventional PI control. Copyright © 2012 ISA. Published by Elsevier Ltd. All rights reserved.

  3. Quantum control spectroscopy of vibrational modes: Comparison of control scenarios for ground and excited states in {beta}-carotene

    Energy Technology Data Exchange (ETDEWEB)

    Hauer, Juergen; Buckup, Tiago [Fachbereich Chemie, Physikalische Chemie, Philipps-Universitaet Marburg, Hans-Meerwein-Strasse, D-35043 Marburg (Germany); Motzkus, Marcus [Fachbereich Chemie, Physikalische Chemie, Philipps-Universitaet Marburg, Hans-Meerwein-Strasse, D-35043 Marburg (Germany)], E-mail: motzkus@staff.uni-marburg.de

    2008-06-23

    Quantum control spectroscopy (QCS) is used as a tool to study, address selectively and enhance vibrational wavepacket motion in large solvated molecules. By contrasting the application of Fourier-limited and phase-modulated excitation on different electronic states, the interplay between the controllability of vibrational coherence and electronic resonance is revealed. We contrast control on electronic ground and excited state by introducing an additional pump beam prior to a DFWM-sequence (Pump-DFWM). Via phase modulation of this initial pump pulse, coherent control is extended to structural evolution on the vibrationally hot ground state (hot-S{sub 0}) and lowest lying excited state (S{sub 1}) of {beta}-carotene. In an open loop setup, the control scenarios for these different electronic states are compared in their effectiveness and mechanism.

  4. Nonclassicality in two-mode BEC

    OpenAIRE

    Giri, Sandip Kumar; Sen, Biswajit; Ooi, C H Raymond; Pathak, Anirban

    2013-01-01

    The operator solution of a completely quantum mechanical Hamiltonian of the Raman processes is used here to investigate the possibility of obtaining intermodal entanglement between different modes involved in the Raman processes (e.g. pump mode, Stokes mode, vibration (phonon) mode and anti-Stokes mode). Intermodal entanglement is reported between a) pump mode and anti-Stokes mode, b) pump mode and vibration (phonon) mode c) Stokes mode and vibration phonon mode, d) Stokes mode and anti-stoke...

  5. Heat flux pattern in detached L-modes and ELM mitigated H-modes with rotating magnetic perturbations in ASDEX Upgrade

    Science.gov (United States)

    Brida, D.; Lunt, T.; Wischmeier, M.; Bernert, M.; Carralero, D.; Faitsch, M.; Feng, Y.; Sehmer, T.; Sieglin, B.; Suttrop, W.; Wolfrum, E.; The ASDEX Upgrade Team; The MST1 Team

    2017-11-01

    For the first time divertor heat and particle fluxes in high-recycling and detached deuterium L- and H-mode plasmas with rotating magnetic perturbations (MPs) have been measured systematically in the ASDEX Upgrade (AUG) tokamak. The capability to rotate the MP field in AUG enabled us to obtain full two-dimensional profiles of the fluxes from measurements with the divertor triple Langmuir probes. As the divertor detached it was found that the initially non-axisymmetric heat flux became increasingly axisymmetric. In particular no ‘burn-through’ of the lobes was observed in the detached divertor in H-mode. Furthermore, the measurements were compared with simulations of the transport code EMC3-EIRENE as well as a simplified model based on field line tracing.

  6. Comment on "Parametric Instability Induced by X-Mode Wave Heating at EISCAT" by Wang et al. (2016)

    Science.gov (United States)

    Blagoveshchenskaya, N. F.; Borisova, T. D.; Yeoman, T. K.

    2017-12-01

    In their recent article Wang et al. (2016) analyzed observations from EISCAT (European Incoherent Scatter) Scientific Association Russian X-mode heating experiments and claimed to explain the potential mechanisms for the parametric decay instability (PDI) and oscillating two-stream instability (OTSI). Wang et al. (2016) claim that they cannot separate the HF-enhanced plasma and ion lines excited by O or X mode in the EISCAT UHF radar spectra. Because of this they distinguished the parametric instability excited by O-/X-mode heating waves according to their different excitation heights. Their reflection heights were determined from ionosonde records, which provide a rough measure of excitation altitudes and cannot be used for the separation of the O- and X-mode effects. The serious limitation in their analysis is the use of a 30 s integration time of the UHF radar data. There are also serious disagreements between their analysis and the real observational facts. The fact is that it is the radical difference in the behavior of the X- and O-mode plasma and ion line spectra derived with a 5 s resolution, which provides the correct separation of the X- and O-mode effects. It is not discussed and explained how the parallel component of the electric field under X-mode heating is generated. Apart from the leakage to the O mode, results by Wang et al. (2016) do not explain the potential mechanisms for PDI and OTSI and add nothing to understanding the physical factors accounting for the parametric instability generated by an X-mode HF pump wave.

  7. Vibrational coherence in polar solutions of Zn(II) tetrakis(N-methylpyridyl)porphyrin with Soret-band excitation: rapidly damped intermolecular modes with clustered solvent molecules and slowly damped intramolecular modes from the porphyrin macrocycle.

    Science.gov (United States)

    Dillman, Kevin L; Shelly, Katherine R; Beck, Warren F

    2009-04-30

    Ground-state coherent wavepacket motions arising from intermolecular modes with clustered, first-shell solvent molecules were observed using the femtosecond dynamic absorption technique in polar solutions of Zn(II) meso-tetrakis(N-methylpyridyl)porphyrin (ZnTMPyP) with excitation in the Soret absorption band. As was observed previously in bacteriochlorophyll a solution, the pump-probe transients in ZnTMPyP solutions are weakly modulated by slowly damped (effective damping time gamma > 1 ps) features that are assigned to intramolecular modes, the skeletal normal modes of vibration of the porphyrin. The 40 cm(-1) and 215 cm(-1) modes from the metal-doming and metal-solvent-ligand modes, respectively, are members of this set of modulation components. A slowly damped 2-4 cm(-1) component is assigned to the internal rotation of the N-methylpyridyl rings with respect to the porphyrin macrocycle; this mode obtains strong resonance Raman intensity enhancement from an extensive delocalization of pi-electron density from the porphyrin in the ground state onto the rings in the pi* excited states. The dominant features observed in the pump-probe transients are a pair of rapidly damped (gamma modes with solvent molecules. This structural assignment is supported by an isotope-dependent shift of the average mode frequencies in methanol and perdeuterated methanol. The solvent dependence of the mean intermolecular mode frequency is consistent with a van der Waals intermolecular potential that has significant contributions only from the London dispersion and induction interactions; ion-dipole or ion-induced-dipole terms do not make large contributions because the pi-electron density is not extensively delocalized onto the N-methylpyridyl rings. The modulation depth associated with the intermolecular modes exhibits a marked dependence on the electronic structure of the solvent that is probably related to the degree of covalency; the strongest modulations are observed in acetonitrile

  8. Vibrational normal modes calculation in the crystalline state of methylated monosaccharides: Anomers of the methyl-D-glucopyranoside and methyl-D-xylopyranoside molecules.

    Science.gov (United States)

    Taleb-Mokhtari, Ilham Naoual; Lazreg, Abbassia; Sekkal-Rahal, Majda; Bestaoui, Noreya

    2016-01-15

    A structural investigation of the organic molecules is being carried out using vibrational spectroscopy. In this study, normal co-ordinate calculations of anomers of the methyl-D-glucopyranoside and methyl-β-D-xylopyranoside in the crystalline state have been performed using the modified Urey-Bradley-Shimanouchi force field (mUBSFF) combined with an intermolecular potential energy function. The latter includes Van der Waals interactions, electrostatic terms, and explicit hydrogen bond functions. The vibrational spectra of the compounds recorded in the crystalline state, in the 4000-500 cm(-1) spectral region for the IR spectra, and in the 4000-20 cm(-1) spectral range for the Raman spectra are presented. After their careful examination, several differences in the intensities and frequency shifts have been observed. The theoretical spectra have been obtained after a tedious refinement of the force constants. Thus, on the basis of the obtained potential distribution, each observed band in IR and in Raman has been assigned to a vibrational mode. The obtained results are indeed in agreement with those observed experimentally and thus confirm the previous assignments made for the methyl-α and β-D-glucopyranoside, as well as for the methyl-β-D-xylopyranoside. Copyright © 2015 Elsevier B.V. All rights reserved.

  9. A user's guide to the SUDAN computer program for determining the vibration modes of structural systems. Ph.D. Thesis - Case Western Reserve Univ., Jun. 1963

    Science.gov (United States)

    Kvaternik, R. G.; Durling, B. J.

    1978-01-01

    The use of the SUDAN computer program for analyzing structural systems for their natural modes and frequencies of vibration is described. SUDAN is intended for structures which can be represented as an equivalent system of beam, spring, and rigid-body substructures. User-written constraint equations are used to analytically join the mass and stiffness matrices of the substructures to form the mass and stiffness matrices of the complete structure from which all the frequencies and modes of the system are determined. The SUDAN program can treat the case in which both the mass and stiffness matrices of the coupled system may be singular simultaneously. A general description of the FORTRAN IV program is given, the computer hardware and software specifications are indicated, and the input required by the program is described.

  10. Full Article: Stoichiometry, Vibrational Modes and Structure of Molten Nb2O5-K2S2O7 Mixtures

    DEFF Research Database (Denmark)

    Boghosian, S.; Borup, F.; Berg, Rolf W.

    1998-01-01

    The dissolution reaction of Nb205 in pure molten K2S207 has been studied and high temperature Raman spectroscopy has been used for determining the vibrational and structural properties of the Nb(V) complex(es) formed according to the reaction Nb205 + n S207(2-) -> complex. By means of a recently ...

  11. Simulation of vibrational energy transfer in two-dimensional infrared spectroscopy of amide I and amide II modes in solution

    NARCIS (Netherlands)

    Bloem, Robbert; Dijkstra, Arend G.; Jansen, Thomas La Cour; Knoester, Jasper

    2008-01-01

    Population transfer between vibrational eigenstates is important for many phenomena in chemistry. In solution, this transfer is induced by fluctuations in molecular conformation as well as in the surrounding solvent. We develop a joint electrostatic density functional theory map that allows us to

  12. Synthesis, vibrational spectra, and normal mode analysis of nickel(II) 1,5-dihydroxy-1,5-dimethyloctaethylbacteriochlorin. A model for bacteriochlorophylls

    Energy Technology Data Exchange (ETDEWEB)

    Hu, S.; Mukherjee, A.; Spiro, T.G. (Princeton Univ., NJ (United States))

    1993-12-29

    Resonance Raman (RR) and FT-IR spectra are reported for nickel(II) 1,5-dihydroxy-1,5-dimethyloctaethylbacteriochlorin [Ni(HOEBC)] and its meso-d[sub 4] isotopomer. All the in-plane skeletal RR-active modes and most IR-active modes are assigned with the aid of a normal mode analysis by using a force field developed for nickel(II) octaethylporphyrin and by scaling the bond stretch force constants to bond lengths revealed in the crystal structure of nickel(II) octaethylbacteriochlorin. The calculated eigenvectors provide insight into the essential vibrational characteristics of metallobacteriochlorins. The RR spectra of Ni(HOEBC) were acquired with a variety of excitation wavelengths, near resonance with the B[sub x], Q[sub x], and Q[sub y] transitions. The enhancement pattern of the observed RR intensities reveals that the B[sub x]- and near-Q[sub y]-resonant spectra are dominated by Franck-Condon-active modes while the Q[sub x]-resonant spectrum is dominated by vibronically active modes. The B[sub x]-resonant spectrum also shows significant vibronic scattering, via coupling between the B[sub x]- and B[sub y]-excited states. Frequencies correlate well among Ni(II) complexes of octaethylporphine (OEP) and hydroporphyrins for modes containing similar local mode contributions, when allowance is made for C[sub beta]-C[sub beta] bond order reduction and the effects of symmetry lowering. Assignments are proposed for the existing RR data on bacteriochlorophyll a. 32 refs., 14 figs., 6 tabs.

  13. A New Fuzzy Sliding Mode Controller with a Disturbance Estimator for Robust Vibration Control of a Semi-Active Vehicle Suspension System

    Directory of Open Access Journals (Sweden)

    Byung-Keun Song

    2017-10-01

    Full Text Available This paper presents a new fuzzy sliding mode controller (FSMC to improve control performances in the presence of uncertainties related to model errors and external disturbance (UAD. As a first step, an adaptive control law is designed using Lyapunov stability analysis. The control law can update control parameters of the FSMC with a disturbance estimator (DE in which the closed-loop stability and finite-time convergence of tracking error are guaranteed. A solution for estimating the compensative quantity of the impact of UAD on a control system and a set of solutions are then presented in order to avoid the singular cases of the fuzzy-based function approximation, increase convergence ability, and reduce the calculating cost. Subsequently, the effectiveness of the proposed controller is verified through the investigation of vibration control performances of a semi-active vehicle suspension system featuring a magnetorheological damper (MRD. It is shown that the proposed controller can provide better control ability of vibration control with lower consumed power compared with two existing fuzzy sliding mode controllers.

  14. Resonance Raman and vibrational mode analysis used to predict ligand geometry for docking simulations of a water soluble porphyrin and tubulin.

    Science.gov (United States)

    McMicken, Brady; Parker, James E; Thomas, Robert J; Brancaleon, Lorenzo

    2016-09-01

    The ability to modify the conformation of a protein by controlled partial unfolding may have practical applications such as inhibiting its function or providing non-native photosensitive properties. A water-soluble porphyrin, meso-tetrakis (p-sulfonatophenyl) porphyrin (TSPP), non-covalently bound to tubulin can be used as a photosensitizer, which upon irradiation can lead to conformational changes of the protein. To fully understand the mechanism responsible for this partial unfolding and determine the amino acid residues and atoms involved, it is essential to find the most likely binding location and the configuration of the ligand and protein. Techniques typically used to analyze atomic position details, such as nuclear magnetic resonance and X-ray crystallography, require large concentrations, which are incompatible with the dilute conditions required in experiments for photoinduced mechanisms. Instead, we develop an atomistic description of the TSPP-tubulin complex using vibrational mode analysis from density functional theory calculations correlated to resonance Raman spectra of the porphyrin paired with docking simulations. Changes in the Raman peaks of the porphyrin molecule correlate with changes in its structural vibrational modes when bound to tubulin. The data allow us to construct the relative geometry of the porphyrin when bound to protein, which are then used with docking simulations to find the most likely configuration of the TSPP-tubulin complex.

  15. Importance of C*-H based modes and large amplitude motion effects in vibrational circular dichroism spectra: the case of the chiral adduct of dimethyl fumarate and anthracene.

    Science.gov (United States)

    Passarello, Marco; Abbate, Sergio; Longhi, Giovanna; Lepri, Susan; Ruzziconi, Renzo; Nicu, Valentin Paul

    2014-06-19

    The role played by the C*-H based modes (C* being the chiral carbon atom) and the large amplitude motions in the vibrational absorption (VA) and vibrational circular dichroism (VCD) spectra is investigated. The example of an adduct of dimethyl fumarate and anthracene, i.e., dimethyl-(+)-(11R,12R)-9,10-dihydro-9,10-ethanoanthracene-11,12-dicarboxylate, and two deuterated isotopomers thereof specially synthesized for this goal, are considered. By comparing the experimental and DFT calculated spectra of the undeuterated and deuterated species, we demonstrate that the C*-H bending, rocking, and stretching modes in the VA and VCD spectra are clearly identified in well defined spectroscopic features. Further, significant information about the conformer distribution is gathered by analyzing the VA and VCD data of both the fingerprint and the C-H stretching regions, with particular attention paid to the band shape data. Effects related to the large amplitude motions of the two methoxy moieties have been simulated by performing linear transit (LT) calculations, which consists of varying systematically the relative positions of the two methoxy moieties and calculating VCD spectra for the partially optimized structures obtained in this way. The LT method allows one to improve the quality of calculated spectra, as compared to experimental results, especially in regard to relative intensities and bandwidths.

  16. Modeling of heat transfer and fluid flow in keyhole mode welding

    Science.gov (United States)

    Rai, Rohit

    In this work, computationally efficient numerical models have been developed for linear keyhole mode LBW and EBW processes. The models combine an energy balance based model for keyhole geometry calculation with a well tested 3D heat transfer and fluid flow model. For LBW, keyhole wall temperatures are assumed to be equal to the boiling point of the alloy at 1 atm pressure. Keyhole wall temperatures in EBW are calculated from the equilibrium vapor pressure versus temperature relation for the work-piece material. The vapor pressure is, in turn, calculated from a force balance at the keyhole walls between the surface tension, vapor pressure and hydrostatic forces. A turbulence model is used to estimate the effective values of viscosity and thermal conductivity to account for the enhanced heat and mass transport in the turbulent weld pool due to the fluctuating components of velocities in both LBW and EBW. The proposed model for LBW has been tested for materials with wide ranging thermo-physical properties under varying input powers and welding speeds covering both partial and full penetration welds. The tested materials include Al 5754 alloy, A131 steel, 304L stainless steel, Ti-6Al-4V, tantalum, and vanadium. These materials vary significantly in their thermo-physical properties, including boiling point, thermal conductivity, and specific heat. The EBW model was tested for 21Cr-6Ni-9Mn steel, 304L stainless steel, and Ti-6Al-4V for different input powers and power density distributions. To improve the agreement between the calculated and experimental results, a methodology is presented to estimate the values of uncertain input parameters like absorption coefficient and beam radius using a genetic algorithm with the numerical model and limited amount of experimental data. Finally, a genetic algorithm is used with the numerical model to prescribe welding conditions that would result in a desired weld attribute. The computed weld cross-sectional geometries and thermal

  17. Comprehensive stability analysis of disc brake vibrations including gyroscopic, negative friction slope and mode-coupling mechanisms

    Science.gov (United States)

    Kang, Jaeyoung; Krousgrill, Charles M.; Sadeghi, Farshid

    2009-07-01

    The current study investigates the disc brake squeal by using an annular disc in contact with two pads subject to distributed friction stresses. The disc and pads are modeled as rotating annular and stationary annular sector plates, respectively. Friction stress is described on the deformed disc surface as distributed non-conservative friction-couples and frictional follower forces. From disc doublet-mode and multiple-mode models, the mode-coupling mechanism influenced by disc rotation is examined. In automotive applications, the frictional mode-coupling resulting from friction couple is shown to be the major mechanism for dynamic destabilization, whereas the effects of disc rotation on flutter destabilization are found to be small. On the verge of stop, however, the rotation effects effectively stabilize the steady sliding. This comprehensive brake model has shown that there is a speed corresponding to maximum squeal propensity for each flutter mode.

  18. Reduction of the heat leak in superconducting system at half-wave-rectified current mode by peltier current lead

    CERN Document Server

    Yamaguchi, T; Nakamura, K; Yamaguchi, S; Hasegawa, Y

    2002-01-01

    Experiments of Peltier current lead (PCL) were performed by the way of half-wave-rectified current (HWRC) for an evaluation of the PCL system in the drive with the large-rippled current. The current ripple of the HWRC is large, and we discussed the cooling capability of the current ripple. The experimental results revealed that the temperature difference of the thermoelectric-element (TE) increased with the magnitude of the current in the PCL system, despite the large current ripple. Calorimetric measurements revealed that the PCL reduced the heat leak of 60% for the peak current 90A. We compared the PCL systems of the direct current (dc) mode and the HWRC mode. The results showed that the current dependence of the temperature difference in the HWRC mode did not match that of the dc mode, but those of the heat leak matched well. The performance of the Peltier cooling in the HWRC mode is reduced to be 2/pi time of the Seebeck coefficient for the dc mode by using the time-average method. (author)

  19. Configuration and Heating Power Dependence of Edge Parameters and H-mode Dynamics in National Spherical Torus Experiment (NSTX)

    Energy Technology Data Exchange (ETDEWEB)

    C.E. Bush; M.G. Bell; R.E. Bell; J. Boedo; E.D. Fredrickson; S.M. Kaye; S. Kubota; B.P. LeBlanc; R. Maingi; R.J. Maqueda; S.A. Sabbagh; V.A. Soukhanovskii; D. Stutman; D.W. Swain; J.B. Wilgen; S.J. Zweben; W.M. Davis; D.A. Gates; D.W. Johnson; R. Kaita; H.W. Kugel; D. Mastrovito; S. Medley; J.E. Menard; D. Mueller; M. Ono; F. Paoletti; S.J. Paul; Y-K.M. Peng; R. Raman; P.G. Roney; A.L. Roquemore; C.H. Skinner; E.J. Synakowski; G. Taylor; the NSTX Team

    2003-01-09

    Edge parameters play a critical role in H-mode (high-confinement mode) access, which is a key component of plasma discharge optimization in present-day toroidal confinement experiments and the design of next-generation devices. Because the edge magnetic topology of a spherical torus (ST) differs from a conventional aspect ratio tokamak, H-modes in STs exhibit important differences compared with tokamaks. The dependence of the NSTX (National Spherical Torus Experiment) edge plasma on heating power, including the L-H transition requirements and the occurrence of edge-localized modes (ELMs), and on divertor configuration is quantified. Comparisons between good L-modes (low-confinement modes) and H-modes show greater differences in the ion channel than the electron channel. The threshold power for the H-mode transition in NSTX is generally above the predictions of a recent ITER (International Thermonuclear Experimental Reactor) scaling. Correlations of transition and ELM phenomena with turbulent fluctuations revealed by Gas Puff Imaging (GPI) and reflectometry are observed. In both single-null and double-null divertor discharges, the density peaks off-axis, sometimes developing prominent ''ears'' which can be sustained for many energy confinement times, tau subscript ''E'', in the absence of ELMs. A wide variety of ELM behavior is observed, and ELM characteristics depend on configuration and fueling.

  20. Component mode synthesis and large deflection vibration of complex structures. Volume 1: Examples of NASTRAN modal synthesis capability

    Science.gov (United States)

    Mei, Chuh; Shen, Mo-How

    1987-01-01

    The use of NASTRAN model synthesis capability is illustrated. A classical truss problem is examined and the results are compared to results from other methods to test for accuracy. The problem is examined using both fixed interface modes and free interface modes. The solution is carried out for an applied dynamic load as far as recovery of forces in individual members as a function of time. Another small beam problem is used to compare different means of combining substructures.

  1. Effects of topological defects and diatom vacancies on characteristic vibration modes and Raman intensities of zigzag single-walled carbon nanotubes.

    Science.gov (United States)

    Saidi, Wissam A

    2014-09-04

    Defects are ubiquitous in carbon nanotubes (CNTs), despite their large formation energies, and have astounding effects on their physicochemical properties. In this study, we employ density-functional theory (DFT) calculations to study systematically the atomic structure, stability, and characteristic vibrations of pristine and defected zigzag CNTs, where the defects are of the form of Stone-Wales (SW) and diatom vacancies (DV). The DFT optimized structures and the phonon modes are subsequently used in conjunction with a semiempirical bond-polarization model to study the nonresonant Raman spectra. For each defect type, we find two CNT structures with defects parallel or oblique to the tube axis. For the SW defects, the two structures have similar formation energies, whereas for the DV defect, only defects parallel to the tube axis are likely to exist. The results show that the defects induce a blue shift in the radial breathing mode (RBM) of metallic CNTs, whereas this mode is not shifted for semiconducting CNTs. However, the RBM shift or its Raman profile is not sensitive to the defect type. The G-band showed more sensitivity to the defects in the form of a red/blue shift in the frequency, or a partial/complete defragmentation of the G bands.

  2. New Edge Localized Modes at Marginal Input Power with Dominant RF-heating and Lithium-wall Conditioning in EAST

    DEFF Research Database (Denmark)

    Wang, H.; Xu, G.; Guo, H.

    The EAST tokamak has achieved, for the rst time, the ELMy H-mode at a connement improvement factor HITER89P 1:7, with dominant RF heating and active wall conditioning by lithium evaporation and real-time injection of Li powder. During the H-mode phase, a new small-ELM regime has been observed...... of zonal flows. New observations have also been made on the type-III ELMs. Measurements from Mach probes have demonstrated a decreasing co-current rotation during type-III ELMs. These suggest that the type-III ELMs may transport substantial particles, energy and momentum out of the plasma. Each type...

  3. The toluene-Ar complex: S0 and S1 van der Waals modes, changes to methyl rotation, and torsion-van der Waals vibration coupling.

    Science.gov (United States)

    Gascooke, Jason R; Lawrance, Warren D

    2013-02-28

    The methyl rotor and van der Waals vibrational levels in the S1 and S0 states of toluene-Ar have been investigated by the technique of two-dimensional laser induced fluorescence (2D-LIF). The S0 van der Waals and methyl rotor levels are reported for the first time, while improved S1 values are presented. The correlations seen in the 2D-LIF images between the S0 and S1 states lead to a reassignment of key features in the S1 ← S0 excitation spectrum. This reassignment reveals that there are significant changes in the methyl rotor levels in the complex compared with those in bare toluene, particularly at low m. The observed rotor energies are explained by the introduction of a three-fold, V3, term in the torsion potential (this term is zero in toluene) and a reduction in the height of the six-fold, V6, barriers in S0 and S1 from their values in bare toluene. The V3 term is larger in magnitude than the V6 term in both S0 and S1. The constants determined are ∣V3(S1)∣ = 33.4 ± 1.0 cm(-1), ∣V3(S0)∣ = 20.0 ± 1.0 cm(-1), V6(S1) = -10.7 ± 1.0 cm(-1), and V6(S0) = -1.7 ± 1.0 cm(-1). The methyl rotor is also found to couple with van der Waals vibration; specifically, the m(") = 2 rotor state couples with the combination level involving one quantum of the long axis bend and m(") = 1. The coupling constant is determined to be 1.9 cm(-1), which is small compared with the values typically reported for torsion-vibration coupling involving ring modes.

  4. The toluene-Ar complex: S0 and S1 van der Waals modes, changes to methyl rotation, and torsion-van der Waals vibration coupling

    Science.gov (United States)

    Gascooke, Jason R.; Lawrance, Warren D.

    2013-02-01

    The methyl rotor and van der Waals vibrational levels in the S1 and S0 states of toluene-Ar have been investigated by the technique of two-dimensional laser induced fluorescence (2D-LIF). The S0 van der Waals and methyl rotor levels are reported for the first time, while improved S1 values are presented. The correlations seen in the 2D-LIF images between the S0 and S1 states lead to a reassignment of key features in the S1 ← S0 excitation spectrum. This reassignment reveals that there are significant changes in the methyl rotor levels in the complex compared with those in bare toluene, particularly at low m. The observed rotor energies are explained by the introduction of a three-fold, V3, term in the torsion potential (this term is zero in toluene) and a reduction in the height of the six-fold, V6, barriers in S0 and S1 from their values in bare toluene. The V3 term is larger in magnitude than the V6 term in both S0 and S1. The constants determined are |V3(S1)| = 33.4 ± 1.0 cm-1, |V3(S0)| = 20.0 ± 1.0 cm-1, V6(S1) = -10.7 ± 1.0 cm-1, and V6(S0) = -1.7 ± 1.0 cm-1. The methyl rotor is also found to couple with van der Waals vibration; specifically, the m″ = 2 rotor state couples with the combination level involving one quantum of the long axis bend and m″ = 1. The coupling constant is determined to be 1.9 cm-1, which is small compared with the values typically reported for torsion-vibration coupling involving ring modes.

  5. The molecular structure, geometry, stability, thermal and fundamental modes of vibration of glycine dimer by DFT methods.

    Science.gov (United States)

    Kishor Kumar, J; Gunasekaran, S; Loganathan, S; Anand, G; Kumaresan, S

    2013-11-01

    Glycine is an important amino acid for building up protein synthesis. Single crystal of glycine dimer was grown from aqueous solution by slow evaporation method. Powder X-ray diffraction analysis confirms the crystalline nature of grown crystal. It is interesting to study the molecular structure of a dimer, having well-defined channels formed through amphoterism bonding between CO⋯H bonds with split-valence basis sets, and the conformer is mirror symmetrical, in which the protonated organic cation plays a significant role to have a dimer pattern. Amphiprotic molecules, like dimeric glycine which can either donate or accept a proton (H(+)) from each other. Optical absorption study reveals that the transparency of the crystal in the entire visible region and the cutoff wavelength was found to be 235nm. Powder SHG test and thermogravimetric analysis shows glycine dimer crystal is optically active and thermally stable. The molecular structure, geometry, stability and theoretical vibrational spectra were calculated for glycine as a monomer and as a dimer linked by the amphoterism hydrogen bonding. The theoretical studies were performed using the B3LYP density functional method with the 6-311G (d,p) basis set. The detailed interpretation of the vibrational spectra has been made on the basis of normal coordinate analysis. Copyright © 2013 Elsevier B.V. All rights reserved.

  6. N-H stretching modes around 3300 wavenumber from peptide backbones observed by chiral sum frequency generation vibrational spectroscopy.

    Science.gov (United States)

    Fu, Li; Wang, Zhuguang; Yan, Elsa C Y

    2014-09-01

    We present a detailed analysis of the molecular origin of the chiral sum frequency generation (SFG) signals of proteins and peptides at interfaces in the N-H stretching vibrational region. The N-H stretching can be a probe for investigating structural and functional properties of proteins, but remains technically difficult to analyze due to the overlapping with the O-H stretching of water molecules. Chiral SFG spectroscopy offers unique tools to study the N-H stretching from proteins at interfaces without interference from the water background. However, the molecular origin of the N-H stretching signals of proteins is still unclear. This work provides a justification of the origin of chiral N-H signals by analyzing the vibrational frequencies, examining chiral SFG theory, studying proton (hydrogen/deuterium) exchange kinetics, and performing optical control experiments. The results demonstrate that the chiral N-H stretching signals at ~3300 cm(-1) originate from the amide group of the protein backbones. This chiral N-H stretching signal offers an in situ, real-time, and background-free probe for interrogating the protein structures and dynamics at interfaces at the molecular level. © 2014 Wiley Periodicals, Inc.

  7. Vibrational mode-selected differential scattering of NH3+ methanol (d1, d3, d4): Control of product branching by hydrogen-bonded complex formation

    Science.gov (United States)

    Fu, Hungshin; Qian, Jun; Green, Richard J.; Anderson, Scott L.

    1998-02-01

    We report a study of vibrational mode effects and differential scattering in reaction of NH3+ with CD3OD, CD3OH, and CH3OD over the collision energy range from 0.1 to 5 eV. At low collision energies, abstraction of both methyl and hydroxyl D atoms is observed with roughly equal probability, even though methyl D-abstraction should be favored on both energetic and statistical grounds. Branching between the two abstraction reactions is controlled by two different hydrogen-bonded complexes. Formation of these complexes is enhanced by NH3+ umbrella bending, unaffected by the NH3+ symmetric stretch, and inhibited by collision energy. Endoergic proton transfer is mediated at low energies by a third hydrogen-bonded complex, formation of which is enhanced by both umbrella bending and the symmetric stretch. Charge transfer (CT) has a significant cross section only when the NH3+ umbrella bend excitation exceeds the endoergicity. Collision energy and symmetric stretching appear to have no effect on CT. At high collision energies all reactions become direct, with near spectator stripping dynamics. In this energy range product branching appears to be controlled by collision geometry and there are no significant vibrational effects.

  8. A Robust Vibration Control of a Magnetorheological Damper Based Railway Suspension Using a Novel Adaptive Type 2 Fuzzy Sliding Mode Controller

    Directory of Open Access Journals (Sweden)

    Sy Dung Nguyen

    2017-01-01

    Full Text Available This work proposes a novel adaptive type 2 fuzzy sliding controller (AT2FC for vibration control of magnetorheological damper- (MRD- based railway suspensions subjected to uncertainty and disturbance (UAD. The AT2FC is constituted of four main parts. The first one is a sliding mode controller (SMC for specifying the main damping force supporting the suspension. This controller is designed via Lyapunov stability theory. The second one is an interpolation model based on an interval type 2 fuzzy logic system for determination of optimal parameters of the SMC. The third one is a nonlinear UAD observer to compensate for external disturbances. The fourth one is an inverse MRD model (T2F-I-MRD for specifying the input current. In the operating process, an adaptively optimal structure deriving from the SMC is created (called the Ad-op-SMC to adapt to the real status. Working as an actuator, the input current for MRD is then determined by the T2F-I-MRD to generate the required damping force which is estimated by the Ad-op-SMC and the nonlinear observer. It is shown that the obtained survey results reflect the AT2FC’s excellent vibration control performance compared with the other controllers.

  9. Vibrational transitions in hydrogen bonded bimolecular complexes – A local mode perturbation theory approach to transition frequencies and intensities

    DEFF Research Database (Denmark)

    Mackeprang, Kasper; Kjærgaard, Henrik Grum

    2017-01-01

    The local mode perturbation theory (LMPT) model was developed to improve the description of hydrogen bonded XH-stretching transitions, where X is typically O or N. We present a modified version of the LMPT model to extend its application from hydrated bimolecular complexes to hydrogen bonded...... bimolecular complexes with donors such as alcohols, amines and acids. We have applied the modified model to a series of complexes of different hydrogen bond type and complex energy. We found that the differences between local mode (LM) and LMPT calculated fundamental XH-stretching transition wavenumbers...

  10. Legal governance of smart heat infrastructure development under modes of liberalization : How to analyze and overcome deadlocks in heat projects

    NARCIS (Netherlands)

    Heldeweg, Michiel A.; Sanders, Maurits Ph Th; Brunnekreef, Anne V.

    2017-01-01

    The background of this article is how the challenge to accomplish a sustainable energy transition—in service of various objectives, such as environmental and geopolitical concerns—has recently brought the development of smart heat infrastructures to the public agenda. Especially in Metropolitan

  11. Two-dimensional spectroscopy for harmonic vibrational modes with nonlinear system-bath interactions. II. Gaussian-Markovian case

    NARCIS (Netherlands)

    Tanimura, Y; Steffen, T

    2000-01-01

    The relaxation processes in a quantum system nonlinearly coupled to a harmonic Gaussian-Markovian heat bath are investigated by the quantum Fokker-Planck equation in the hierarchy form. This model describes frequency fluctuations in the quantum system with an arbitrary correlation time and thus

  12. The impact of heating the breakdown bubble on the global mode of a swirling jet: Experiments and linear stability analysis

    Science.gov (United States)

    Rukes, Lothar; Sieber, Moritz; Paschereit, C. Oliver; Oberleithner, Kilian

    2016-10-01

    This study investigates the dynamics of non-isothermal swirling jets undergoing vortex breakdown, with an emphasis on helical coherent structures. It is proposed that the dominant helical coherent structure can be suppressed by heating the recirculation bubble. This proposition is assessed with stereo Particle Image Velocimetry (PIV) measurements of the breakdown region of isothermal and heated swirling jets. The coherent kinetic energy of the dominant helical structure was derived from PIV snapshots via proper orthogonal decomposition. For one set of experimental parameters, mild heating is found to increase the energy content of the dominant helical mode. Strong heating leads to a reduction by 30% of the coherent structures energy. For a second set of experimental parameters, no alteration of the dominant coherent structure is detectable. Local linear stability analysis of the time-averaged velocity fields shows that the key difference between the two configurations is the density ratio at the respective wavemaker location. A density ratio of approximately 0.8 is found to correlate to a suppression of the global mode in the experiments. A parametric study with model density and velocity profiles indicates the most important parameters that govern the local absolute growth rate: the density ratio and the relative position of the density profiles and the inner shear layer.

  13. Vibrational transitions in hydrogen bonded bimolecular complexes - A local mode perturbation theory approach to transition frequencies and intensities

    Science.gov (United States)

    Mackeprang, Kasper; Kjaergaard, Henrik G.

    2017-04-01

    The local mode perturbation theory (LMPT) model was developed to improve the description of hydrogen bonded XH-stretching transitions, where X is typically O or N. We present a modified version of the LMPT model to extend its application from hydrated bimolecular complexes to hydrogen bonded bimolecular complexes with donors such as alcohols, amines and acids. We have applied the modified model to a series of complexes of different hydrogen bond type and complex energy. We found that the differences between local mode (LM) and LMPT calculated fundamental XH-stretching transition wavenumbers and oscillator strengths were correlated with the strength of the hydrogen bond. Overall, we have found that the LMPT model in most cases predicts transition wavenumbers within 20 cm-1 of the experimental values.

  14. The Effect of a Rapid Heating Rate, Mechanical Vibration and Surfactant Chemistry on the Structure–Property Relationships of Epoxy/Clay Nanocomposites

    Directory of Open Access Journals (Sweden)

    Kevin Magniez

    2013-08-01

    Full Text Available The role of processing conditions and intercalant chemistry in montmorillonite clays on the dispersion, morphology and mechanical properties of two epoxy/clay nanocomposite systems was investigated in this paper. This work highlights the importance of employing complementary techniques (X-ray diffraction, small angle X-ray scattering, optical microscopy and transmission electron microscopy to correlate nanomorphology to macroscale properties. Materials were prepared using an out of autoclave manufacturing process equipped to generate rapid heating rates and mechanical vibration. The results suggested that the quaternary ammonium surfactant on C30B clay reacted with the epoxy during cure, while the primary ammonium surfactant (I.30E catalysed the polymerisation reaction. These effects led to important differences in nanocomposite clay morphologies. The use of mechanical vibration at 4 Hz prior to matrix gelation was found to facilitate clay dispersion and to reduce the area fraction of I.30E clay agglomerates in addition to increasing flexural strength by over 40%.

  15. On the phase between pressure and heat release fluctuations for propane/hydrogen flames and its role in mode transitions

    KAUST Repository

    Hong, Seunghyuck

    2013-12-01

    This paper presents an experimental investigation into mode-transitions observed in a 50-kW, atmospheric pressure, backward-facing step combustor burning lean premixed C3H8/H2 fuel mixtures over a range of equivalence ratios, fuel compositions and preheat temperatures. The combustor exhibits distinct acoustic response and dynamic flame shape (collectively referred to as "dynamic modes") depending on the operating conditions. We simultaneously measure the dynamic pressure and flame chemiluminescence to examine the phase between pressure (p\\') and heat release fluctuations (q\\') in the observed dynamic modes. Results show that the heat release is in phase with the pressure oscillations (θqp≈0) at the onset of a dynamic mode, while as the operating conditions change within the mode, the phase grows until it reaches a critical value θqp=θc, at which the combustor switches to another dynamic mode. According to the classical Rayleigh criterion, this critical phase (θc) should be π/2, whereas our data show that the transition occurs well below this value. A linear acoustic energy balance shows that this critical phase marks the point where acoustic losses across the system boundaries equal the energy addition from the combustion process to the acoustic field. Based on the extended Rayleigh criterion in which the acoustic energy fluxes through the system boundaries as well as the typical Rayleigh source term (p\\'q\\') are included, we derive an extended Rayleigh index defined as Re=θqp/θc, which varies between 0 and 1. This index, plotted against a density-weighted strained consumption speed, indicates that the impact of the operating parameters on the dynamic mode selection of the combustor collapses onto a family of curves, which quantify the state of the combustor within a dynamic mode. At Re=0, the combustor enters a mode, and switches to another as Re approaches 1. The results provide a metric for quantifying the instability margins of fuel

  16. Non-Gaussian statistics of amide I mode frequency fluctuation of N-methylacetamide in methanol solution: Linear and nonlinear vibrational spectra

    Science.gov (United States)

    Kwac, Kijeong; Lee, Hochan; Cho, Minhaeng

    2004-01-01

    By carrying out molecular dynamics simulations of an N-methylacetamide (NMA) in methanol solution, the amide I mode frequency fluctuation and hydrogen bonding dynamics were theoretically investigated. Combining an extrapolation formula developed from systematic ab initio calculation studies of NMA-(CH3OH)n clusters with a classical molecular dynamics simulation method, we were able to quantitatively describe the solvatochromic vibrational frequency shift induced by the hydrogen-bonding interaction between NMA and solvent methanol. It was found that the fluctuating amide I mode frequency distribution is notably non-Gaussian and it can be decomposed into two Gaussian peaks that are associated with two distinctively different solvation structures. The ensemble-average-calculated linear response function associated with the IR absorption is found to be oscillating, which is in turn related to the doublet amide I band shape. Numerically calculated infrared absorption spectra are directly compared with experiment and the agreement was found to be excellent. By using the Onsager's regression hypothesis, the rate constants of the interconversion process between the two solvation structures were obtained. Then, the nonlinear response functions associated with two-dimensional infrared pump-probe spectroscopy were simulated. The physics behind the two-dimensional line shape and origin of the cross peaks in the time-resolved pump-probe spectra is explained and the result is compared with 2D spectra experimentally measured recently by Woutersen et al. [S. Woutersen, Y. Mu, G. Stock, and P. Hamm, Chem. Phys. 266, 137 (2001)].

  17. Contribution of mode coupling and phase-mixing of Alfvén waves to coronal heating

    Science.gov (United States)

    Pagano, Paolo; De Moortel, Ineke

    2017-04-01

    The solar corona is a million degree plasma that has been investigated for long time to understand the cause of this high heating rate. In particular, phase-mixing of Alfvén waves in the solar corona has been identified as one possible candidate to explain coronal heating by observations of ubiquitous oscillations in the corona carrying sufficient wave energy and by theoretical models that have described the concentration of energy in small scale structures. The aim of this work is to assess how much energy can be converted into thermal energy by a phase-mixing process triggered by the propagation of Alfvénic waves in a cylindric coronal structure, such as a coronal loop, and to estimate the impact of this conversion on the coronal heating and thermal structure of the solar corona plasma. We run 3D MHD simulations of a magnetised cylinder where the Alfvén speed varies through a boundary shell and a footpoint driver is set to trigger kink modes which mode couple to torsional Alfvén modes in the boundary shell. These Alfvén waves are expected to phase-mix and the system allows us to study the following thermal energy deposition on the plasma. We run a reference simulation to explain the main process and then we vary simulation parameters, such as the size of the boundary shell, its structure and the persistence of the driver. Taking into consideration high values of magnetic resistivity and strong footpoint drivers, we find i) that phase-mixing leads to a temperature increase, ii) that this energy is able to balance the radiative losses only in the localised region involved in the heating.

  18. Common-Mode EMI Reduction in Switching Flyback Power Supply by Implementing Cancellation Method of Heat-Sink Capacitor

    Directory of Open Access Journals (Sweden)

    Mohammad Rouholah Yazdani

    2015-01-01

    Full Text Available Electromagnetic compatibility in switching power converters which are noise sources themselves, has a special importance. Electromagnetic interference (EMI in the form of conducted or radiated reaches to sensitive sections and interferes with their operation. On the other, electromagnetic compatibility (EMC standards causes another forces to reduce noise in switching converters. Major part of noise is due to the common-mode (CM current passes through parasitic elements to the circuit ground (Earth. One of the important parasitic elements from the CM noise viewpoint is the switch heat-sink capacitor (common-mode capacitor. In this paper, a cancellation method of the heat-sink capacitor via a passive circuit is proposed in a 50W isolated flyback converter and is also modeled in OrCAD software. Also, experimental measurement results of the CM electromagnetic interference in regular and proposed flyback converter prototypes are presented to examine the modeling accuracy. Based on the experimental results, significant reduction of CM-EMI is verified after applying the cancellation method of the heat-sink capacitor.

  19. Heat transport and coupling modes in Rayleigh-Bénard convection occurring between two layers with largely different viscosities

    Science.gov (United States)

    Yoshida, Masaki; Iwamori, Hikaru; Hamano, Yozo; Suetsugu, Daisuke

    2017-09-01

    A high-resolution numerical simulation model in two-dimensional cylindrical geometry was used to discuss the heat transport and coupling modes in two-layer Rayleigh-Bénard convection with a high Rayleigh number (up to the order of 109), an infinite Prandtl number, and large viscosity contrasts (up to 10-3) between an outer, highly viscous layer (HVL) and an inner, low-viscosity layer (LVL). In addition to mechanical and thermal interaction across the HVL-LVL interface, which has been investigated by Yoshida and Hamano ["Numerical studies on the dynamics of two-layer Rayleigh-Bénard convection with an infinite Prandtl number and large viscosity contrasts," Phys. Fluids 28(11), 116601 (2016)], the spatiotemporal analysis in this study provides new insights into (1) heat transport over the entire system between the bottom of the LVL and the top of the HVL, in particular that associated with thermal plumes, and (2) the convection regime and coupling mode of the two layers, including the transition mechanism between the mechanical coupling mode at relatively low viscosity contrasts and the thermal coupling mode at higher viscosity contrasts. Although flow in the LVL is highly time-dependent, it shares the spatially opposite/same flow pattern synchronized to the nearly stationary upwelling and downwelling plumes in the HVL, corresponding to the mechanical/thermal coupling mode. In the transitional regime between the mechanical and thermal coupling modes, the LVL exhibits periodical switching between the two phases (i.e., the mechanical and thermal coupling phases) with a stagnant period. A detailed inspection revealed that the switching was initiated by the instability in the uppermost boundary layer of the LVL. These results suggest that convection in the highly viscous mantle of the Earth controls that of the extremely low-viscosity outer core in a top-down manner under the thermal coupling mode, which may support a scenario of top-down hemispherical dynamics

  20. Contribution of mode-coupling and phase-mixing of Alfvén waves to coronal heating

    Science.gov (United States)

    Pagano, P.; De Moortel, I.

    2017-05-01

    Context. Phase-mixing of Alfvén waves in the solar corona has been identified as one possible candidate to explain coronal heating. While this scenario is supported by observations of ubiquitous oscillations in the corona carrying sufficient wave energy and by theoretical models that have described the concentration of energy in small-scale structures, it is still unclear whether this wave energy can be converted into thermal energy in order to maintain the million-degree hot solar corona. Aims: The aim of this work is to assess how much energy can be converted into thermal energy by a phase-mixing process triggered by the propagation of Alfvénic waves in a cylindric coronal structure, such as a coronal loop, and to estimate the impact of this conversion on the coronal heating and thermal structure of the solar corona. Methods: To this end, we ran 3D MHD simulations of a magnetised cylinder where the Alfvén speed varies through a boundary shell, and a footpoint driver is set to trigger kink modes that mode couple to torsional Alfvén modes in the boundary shell. These Alfvén waves are expected to phase-mix, and the system allows us to study the subsequent thermal energy deposition. We ran a reference simulation to explain the main process and then we varied the simulation parameters, such as the size of the boundary shell, its structure, and the persistence of the driver. Results: When we take high values of magnetic resistivity and strong footpoint drivers into consideration, we find that i) phase-mixing leads to a temperature increase of the order of 105 K or less, depending on the structure of the boundary shell; ii) this energy is able to balance the radiative losses only in the localised region involved in the heating; and iii) we can determine the influence of the boundary layer and the persistence of the driver on the thermal structure of the system. Conclusions: Our conclusion is that as a result of the extreme physical parameters we adopted and the

  1. Age-related changes in ocular vestibular-evoked myogenic potentials via galvanic vestibular stimulation and bone-conducted vibration modes.

    Science.gov (United States)

    Chang, Chih-Ming; Young, Yi-Ho; Cheng, Po-Wen

    2012-12-01

    The age-related changes in ocular vestibular-evoked myogenic potentials (oVEMPs) elicited by galvanic vestibular stimulation (GVS) and bone-conducted vibration (BCV) might be attributed to the morphological degeneration of the vestibular system. This study employed GVS and BCV modes for eliciting oVEMPs in healthy subjects to explore the effect of aging on the vestibulo-ocular reflex (VOR) pathway. Sixty-nine healthy subjects (aged 22-69 years) were divided into 5 groups of 12-19 subjects by decades of age. All subjects underwent oVEMPs using GVS and BCV modes. The prevalence and parameters of oVEMPs, including nI latency, pI latency, nI-pI interval, and nI-pI amplitude were measured and compared. The prevalences of GVS-oVEMPs had nonsignificant differences among all age groups, whereas that of BCV-oVEMPs in the over-60 group was significantly lower than those in the under-60 groups. In GVS-oVEMPs, the group over 60 years had significantly longer nI, pI latencies, and smaller amplitudes when compared with those under 60 years. In BCV-oVEMPs, the nI and pI latencies in the over-60 group were significantly longer than those of the under-60 groups, while the nI-pI amplitudes of groups over 50 years were significantly smaller than those of groups under 50 years. All oVEMP parameters exhibited significant differences between GVS- and BCV-oVEMPs in each age group.

  2. Analyzing the Effect of Capillary Force on Vibrational Performance of the Cantilever of an Atomic Force Microscope in Tapping Mode with Double Piezoelectric Layers in an Air Environment.

    Science.gov (United States)

    Nahavandi, Amir; Korayem, Moharam Habibnejad

    2015-10-01

    The aim of this paper is to determine the effects of forces exerted on the cantilever probe tip of an atomic force microscope (AFM). These forces vary according to the separation distance between the probe tip and the surface of the sample being examined. Hence, at a distance away from the surface (farther than d(on)), these forces have an attractive nature and are of Van der Waals type, and when the probe tip is situated in the range of a₀≤ d(ts) ≤ d(on), the capillary force is added to the Van der Waals force. At a distance of d(ts) ≤ a₀, the Van der Waals and capillary forces remain constant at intermolecular distances, and the contact repulsive force repels the probe tip from the surface of sample. The capillary force emerges due to the contact of thin water films with a thickness of h(c) which have accumulated on the sample and probe. Under environmental conditions a layer of water or hydrocarbon often forms between the probe tip and sample. The capillary meniscus can grow until the rate of evaporation equals the rate of condensation. For each of the above forces, different models are presented. The smoothness or roughness of the surfaces and the geometry of the cantilever tip have a significant effect on the modeling of forces applied on the probe tip. Van der Waals and the repulsive forces are considered to be the same in all the simulations, and only the capillary force is altered in order to evaluate the role of this force in the AFM-based modeling. Therefore, in view of the remarkable advantages of the piezoelectric microcantilever and also the extensive applications of the tapping mode, we investigate vibrational motion of the piezoelectric microcantilever in the tapping mode. The cantilever mentioned is entirely covered by two piezoelectric layers that carry out both the actuation of the probe tip and the measuringof its position.

  3. The effect of cobalt substitution in crystal structure and vibrational modes of CuFe{sub 2}O{sub 4} powders obtained by polymeric precursor method

    Energy Technology Data Exchange (ETDEWEB)

    Silva, M.D.P.; Silva, F.C. [Departamento de Química, CCET, Universidade Federal do Maranhão, 65085-580 São Luís, MA (Brazil); Sinfrônio, F.S.M. [Departamento de Engenharia Elétrica, CCET, Universidade Federal do Maranhão, 65085-580 São Luís, MA (Brazil); Paschoal, A.R. [Departamento de Física, Universidade Federal do Ceará, Campus do Pici, 60455-760 Fortaleza, CE (Brazil); Silva, E.N. [Departamento de Física, CCET, Universidade Federal do Maranhão, 65085-580 São Luís, MA (Brazil); Paschoal, C.W.A., E-mail: paschoal@ufma.br [Departamento de Física, CCET, Universidade Federal do Maranhão, 65085-580 São Luís, MA (Brazil); Department of Materials Science and Engineering, University of California Berkeley, 94720-1760 Berkeley, CA (United States); Department of Physics, University of California Berkeley, 94720-7300 Berkeley, CA (United States)

    2014-01-25

    Highlights: • We synthesized mixed spinels by polymeric precursor method. • We investigated the structural and vibrational properties of the mixed. • We investigated the synthesis condition effects in these properties. • We proposed a complete phonon description for CuFe{sub 2}O{sub 4} and CoFe{sub 2}O{sub 4} spinels. -- Abstract: In this work Co–Cu mixed spinel Co{sub 1−x}Cu{sub x}Fe{sub 2}O{sub 4} powders were obtained by polymeric precursors method at several annealing temperatures between 700 and 1200 °C. The samples were characterized by means of X-ray powder diffraction, confirming the ideal inverse spinel structure for CoFe{sub 2}O{sub 4} sample and the tetragonal distorted inverse spinel structure for CuFe{sub 2}O{sub 4} sample. Based on FWHM evaluation, we estimated that crystallite sizes varies between 27 and 37 nm for the non-substituted samples. The optical-active modes were determined by infrared and Raman spectroscopies. The phonon spectra showed a local tetragonal distortion for mixed samples.

  4. Extracting and Applying SV-SV Shear Modes from Vertical Vibrator Data Across Geothermal Prospects Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Hardage, Bob [Bureau of Economic Geology

    2013-07-01

    This 3-year project was terminated at the end of Year 1 because the DOE Geothermal project-evaluation committee decided one Milestone was not met and also concluded that our technology would not be successful. The Review Panel recommended a ?no-go? decision be implemented by DOE. The Principal Investigator and his research team disagreed with the conclusions reached by the DOE evaluation committee and wrote a scientifically based rebuttal to the erroneous claims made by the evaluators. We were not told if our arguments were presented to the people who evaluated our work and made the ?no-go? decision. Whatever the case regarding the information we supplied in rebuttal, we received an official letter from Laura Merrick, Contracting Officer at the Golden Field Office, dated June 11, 2013 in which we were informed that project funding would cease and instructed us to prepare a final report before September 5, 2013. In spite of the rebuttal arguments we presented to DOE, this official letter repeated the conclusions of the Review Panel that we had already proven to be incorrect. This is the final report that we are expected to deliver. The theme of this report will be another rebuttal of the technical deficiencies claimed by the DOE Geothermal Review Panel about the value and accomplishments of the work we did in Phase 1 of the project. The material in this report will present images made from direct-S modes produced by vertical-force sources using the software and research findings we developed in Phase 1 that the DOE Review Panel said would not be successful. We made these images in great haste when we were informed that DOE Geothermal rejected our rebuttal arguments and still regarded our technical work to be substandard. We thought it was more important to respond quickly rather than to take additional time to create better quality images than what we present in this Final Report.

  5. Study of a pilot photovoltaic-electrolyser-fuel cell power system for a geothermal heat pump heated greenhouse and evaluation of the electrolyser efficiency and operational mode

    Directory of Open Access Journals (Sweden)

    Ileana Blanco

    2014-11-01

    Full Text Available The intrinsic factor of variability of renewable energy sources often limits their broader use. The photovoltaic solar systems can be provided with a power back up based on a combination of an electrolyser and a fuel cell stack. The integration of solar hydrogen power systems with greenhouse heating equipment can provide a possible option for powering stand-alone greenhouses. The aim of the research under development at the experimental farm of Department of Agro-Environmental Sciences of the University of Bari Aldo Moro is to investigate on the suitable solutions of a power system based on photovoltaic energy and on the use of hydrogen as energy vector, integrated with a ground source heat pump for greenhouse heating in a self sustained way. The excess energy produced by a purpose-built array of solar photovoltaic modules supplies an alkaline electrolyser; the produced hydrogen gas is stored in pressured storage tank. When the solar radiation level is insufficient to meet the heat pump power demand, the fuel cell starts converting the chemical energy stored by the hydrogen fuel into electricity. This paper reports on the description of the realised system. Furthermore the efficiency and the operational mode of the electrolyser were evaluated during a trial period characterised by mutable solar radiant energy. Anyway the electrolyser worked continuously in a transient state producing fluctuations of the hydrogen production and without ever reaching the steady-state conditions. The Faradic efficiency, evaluated by means of an empirical mathematic model, highlights that the suitable working range of the electrolyser was 1.5÷2.5 kW and then for hydrogen production more than 0.21 Nm3h–1.

  6. Full dimensional Franck-Condon factors for the acetylene tilde{{A}} 1Au—{tilde{X}} {^1Σ _g^+} transition. I. Method for calculating polyatomic linear—bent vibrational intensity factors and evaluation of calculated intensities for the gerade vibrational modes in acetylene

    Science.gov (United States)

    Park, G. Barratt

    2014-10-01

    Franck-Condon vibrational overlap integrals for the tilde{A} {^1A_u}—{tilde{X}} {^1Σ _g^+} transition in acetylene have been calculated in full dimension in the harmonic normal mode basis. The calculation uses the method of generating functions first developed for polyatomic Franck-Condon factors by Sharp and Rosenstock [J. Chem. Phys. 41(11), 3453-3463 (1964)], and previously applied to acetylene by Watson [J. Mol. Spectrosc. 207(2), 276-284 (2001)] in a reduced-dimension calculation. Because the transition involves a large change in the equilibrium geometry of the electronic states, two different types of corrections to the coordinate transformation are considered to first order: corrections for axis-switching between the Cartesian molecular frames and corrections for the curvilinear nature of the normal modes at large amplitude. The angular factor in the wavefunction for the out-of-plane component of the trans bending mode, ν _4^' ' }, is treated as a rotation, which results in an Eckart constraint on the polar coordinates of the bending modes. To simplify the calculation, the other degenerate bending mode, ν _5^' ' }, is integrated in the Cartesian basis and later transformed to the constrained polar coordinate basis, restoring the conventional v and l quantum numbers. An updated tilde{A}-state harmonic force field obtained recently in the R. W. Field research group is evaluated. The results for transitions involving the gerade vibrational modes are in qualitative agreement with experiment. Calculated results for transitions involving ungerade modes are presented in Paper II of this series [G. B. Park, J. H. Baraban, and R. W. Field, "Full dimensional Franck-Condon factors for the acetylene tilde{A} {^1A_u}—{tilde{X}} {^1Σ _g^+} transition. II. Vibrational overlap factors for levels involving excitation in ungerade modes," J. Chem. Phys. 141, 134305 (2014)].

  7. Electron heat transport in EAST steady-state H-mode discharges with a weak electron internal transport barrier

    Science.gov (United States)

    Du, H.; Ding, S.; Chen, J.; Wang, Y.; Lian, H.; Liu, H.; Zang, Q.; Lyu, B.; Duan, Y.; Xu, G.; Qian, J.; Gong, X.

    2017-10-01

    The global confinement (H98) increases with the internal inductance (1.0 1.2) in the recent steady-state H-mode discharges, which exhibit a weak electron ITB started at ρ = 0.4 in EAST. After turning off ECRH, the stored energy decreases by 30% in 2.5 s. Calculations suggest that both the lower hybrid electron heating and driven current move from the core to large radii after turning off ECRH. Power balance analysis show that the LH deposition profile shift from just inside the ITB to outside the ITB after ECRH termination appears to be responsible for the marked drop in stored energy. The slow stored energy decrease is believed to be connected to the long plasma current profile relaxation time. Linear gyrokinetic simulations indicate increasing low-k instability growth rate from small to large radii, which is consistent with the reduced diffusivity within the ITB. The calculations also show that the CTEM dominate within the ITB, ETG modes grow rapidly outside this region, and that ITG modes dominate near the pedestal top. Work supported by the NNSF of China #11575248.

  8. Lower hybrid heating associated with mode conversion on the Wisconsin octupole

    Energy Technology Data Exchange (ETDEWEB)

    Owens, T.L.

    1979-08-01

    This thesis addresses the following key issues in the lower hybrid frequency range: 1. What are the importent physics aspects of wave propagation and heating in an experimental situation. 2. How effective is plasma heating in the complex magnetic field configuration of the octupole. Experimental work is accomplished by launching 1-10ms pulses of up to 40kW of radio frequency power at 140MHz corresponding to the hot plasma lower hybrid resonance in the octupole. A diploe antenna which is moveable radially and is also rotatable couples wave power to the plasma. Coupling efficiencies greater than 95% are achieved by proper antenna placement near the edge of the plasma radial density profile.

  9. Study on divertor particle and heat fluxes from electric probe measurements during ELMy H-modes in KSTAR

    Energy Technology Data Exchange (ETDEWEB)

    Bak, Jun-Gyo, E-mail: jgbak@nfri.re.kr [National Fusion Research Institute, Daejeon (Korea, Republic of); Kim, Heung-Su [National Fusion Research Institute, Daejeon (Korea, Republic of); Bae, Min-Keun; Chung, Kyu-Sun [Hanyang University, Seoul (Korea, Republic of); Hong, Suk-Ho [National Fusion Research Institute, Daejeon (Korea, Republic of)

    2016-11-01

    Highlights: • The characteristics of the particle and heat fluxes were investigated during ELMs in H-modes under the LSN configuration in the KSTAR tokamak.. • There was relation between the ELM amplitude and the ELM frequency as ΔW{sub ELM}/W{sub TOT} ∝ 1/f{sub ELM} in the range of f{sub ELM} ≤ 200 Hz. • The trends of the peak amplitude of the divertor flux near the OSP during ELMs due to the ELM mitigation and the plasma shaping were investigated. • The ELMs were mitigated by MP field, SMBI and ECH. The ELM mitigations due to the MP field and the SMBI were stronger than one due to the ECH. • Finally, the particle flux, evaluated at the far scrape-off layer (SOL) region, was estimated to less than 1% of the divertor particle flux. - Abstract: The characteristics of the divertor particle and heat fluxes are investigated during ELM bursts in ELMy H-mode plasmas with the lower single null (LSN) configuration in Korea Superconducting Tokamak Advanced Research (KSTAR). The particle and heat fluxes are evaluated from the electric probe measurements at the divertor region. It is found that the peak amplitude of the divertor flux during an ELM burst obtained near the outer strike point (OSP) decreases up to about 20% as the ELM frequency increases by a factor of ∼6.5 due to the ELM mitigation and the plasma shaping, which is similar to the trend of the amplitude versus the frequency of the ELM observed in other tokamaks. The ELMs are mitigated by using several methods as magnetic perturbation (MP) field, supersonic molecular beam injection (SMBI) and electron cyclotron heating (ECH) at the edge region. In addition, the particle flux, evaluated at the far scrape-off layer (SOL) region, is less than 1% of the divertor particle flux. In this work, results from the experimental investigations of particle and heat fluxes during ELM bursts from the electric probe measurements at the divertor and far SOL regions are presented.

  10. Full dimensional Franck-Condon factors for the acetylene ˜{A} 1Au—{˜{X}} {^1Σ _g^+} transition. II. Vibrational overlap factors for levels involving excitation in ungerade modes

    Science.gov (United States)

    Park, G. Barratt; Baraban, Joshua H.; Field, Robert W.

    2014-10-01

    A full-dimensional Franck-Condon calculation has been applied to the tilde{A} 1Au—tilde{X} ^1Σ _g^+ transition in acetylene in the harmonic normal mode basis. Details of the calculation are discussed in Part I of this series. To our knowledge, this is the first full-dimensional Franck-Condon calculation on a tetra-atomic molecule undergoing a linear-to-bent geometry change. In the current work, the vibrational intensity factors for levels involving excitation in ungerade vibrational modes are evaluated. Because the Franck-Condon integral accumulates away from the linear geometry, we have been able to treat the out-of-plane component of trans bend (ν _4^' ' }) in the linear tilde{X} state in the rotational part of the problem, restoring the χ Euler angle and the a-axis Eckart conditions. A consequence of the Eckart conditions is that the out-of-plane component of ν _4^' ' } does not participate in the vibrational overlap integral. This affects the structure of the coordinate transformation and the symmetry of the vibrational wavefunctions used in the overlap integral, and results in propensity rules involving the bending modes of the tilde{X} state that were not previously understood. We explain the origin of some of the unexpected propensities observed in IR-UV laser-induced fluorescence spectra, and we calculate emission intensities from bending levels of the tilde{A} state into bending levels of the tilde{X} state, using normal bending mode and local bending mode basis sets. Our calculations also reveal Franck-Condon propensities for the Cartesian components of the cis bend (ν _5^' ' }), and we predict that the best tilde{A}-state vibrational levels for populating tilde{X}-state levels with large amplitude bending motion localized in a single C-H bond (the acetylene↔vinylidene isomerization coordinate) involve a high degree of excitation in ν _6^' } (cis-bend). Mode ν _4^' } (torsion) populates levels with large amplitude counter-rotational motion of

  11. Free vibration of thermally loaded panels including initial imperfections and post-buckling effects

    Science.gov (United States)

    Murphy, K. D.; Virgin, L. N.; Rizzi, S. A.

    1994-01-01

    A combined theoretical and experimental approach is developed to consider the small amplitude free vibration characteristics of fully clamped panels under the influence of uniform heating. Included in this study are the effects of higher modes, in-plane boundary elasticity, initial imperfections, and post-buckling. Comparisons between theory and experiment reveal excellent agreement.

  12. Evaluation of anomalies during nickel and titanium silicide formation using the effective heat of formation mode

    CSIR Research Space (South Africa)

    Pretorius, R

    1993-11-01

    Full Text Available stream_source_info pretorius_1993.pdf.txt stream_content_type text/plain stream_size 39978 Content-Encoding ISO-8859-1 stream_name pretorius_1993.pdf.txt Content-Type text/plain; charset=ISO-8859-1 Materials Chemistry... and Physics, 36 (1993) 31-38 31 Evaluation of anomalies during nickel and titanium silicide formation using the effective heat of formation model R. Pretorius, C.C. Theron IonSolid Znteraction Division, Van de H.A. Ras and T...

  13. Nonstationary thermal field in the parallelepiped in the mode of heat conduction under boundary conditions of first kind

    Directory of Open Access Journals (Sweden)

    V. K. Bityukov

    2016-01-01

    Full Text Available Analytical study of the processes of heat conduction is one of the main topics of modern engineering research in engineering, energy, nuclear industry, process chemical, construction, textile, food, geological and other industries. Suffice to say that almost all processes in one degree or another are related to change in the temperature condition and the transfer of warmth. It should also be noted that engineering studies of the kinetics of a range of physical and chemical processes are similar to the problems of stationary and nonstationary heat transfer. These include the processes of diffusions, sedimentation, viscous flow, slowing down the neutrons, flow of fluids through a porous medium, electric fluctuations, adsorption, drying, burning, etc. There are various methods for solving the classical boundary value problems of nonstationary heat conduction and problems of the generalized type: the method of separation of variables (Fourier method method; the continuation method; the works solutions; the Duhamel's method; the integral transformations method; the operating method; the method of green's functions (stationary and non-stationary thermal conductivity; the reflection method (method source. In this paper, based on the consistent application of the Laplace transform on the dimensionless time θ and finite sine integral transformation in the spatial coordinates X and Y solves the problem of unsteady temperature distribution on the mechanism of heat conduction in a parallelepiped with boundary conditions of first kind. As a result we have the analytical solution of the temperature distribution in the parallelepiped to a conductive mode free convection, when one of the side faces of the parallelepiped is maintained at a constant temperature, and the others with the another same constant temperature.

  14. Using vibrational infrared biomolecular spectroscopy to detect heat-induced changes of molecular structure in relation to nutrient availability of prairie whole oat grains on a molecular basis.

    Science.gov (United States)

    Rahman, M D Mostafizar; Theodoridou, Katerina; Yu, Peiqiang

    2016-01-01

    To our knowledge, there is little study on the interaction between nutrient availability and molecular structure changes induced by different processing methods in dairy cattle. The objective of this study was to investigate the effect of heat processing methods on interaction between nutrient availability and molecular structure in terms of functional groups that are related to protein and starch inherent structure of oat grains with two continued years and three replication of each year. The oat grains were kept as raw (control) or heated in an air-draft oven (dry roasting: DO) at 120 °C for 60 min and under microwave irradiation (MIO) for 6 min. The molecular structure features were revealed by vibrational infrared molecular spectroscopy. The results showed that rumen degradability of dry matter, protein and starch was significantly lower (P grains are more sensitive to microwave irradiation than dry heating in terms of protein and starch molecular profile and nutrient availability in ruminants.

  15. Localized bulk electron heating with ICRF mode conversion in the JET tokamak

    DEFF Research Database (Denmark)

    Mantsinen, M.J.; Mayoral, M.-L.; Eester, D. Van

    2004-01-01

    of the He-3 ion cyclotron resonance layer in D and He-4 plasmas and subsequently damped on the bulk electrons. The resulting electron power deposition, measured using ICRF power modulation, is narrow with a typical full-width at half-maximum of approximate to30 cm (i.e. about 30% of the minor radius......) and the total deposited power to electrons comprises at least up to 80% of the applied ICRF power. The ICRF mode conversion power deposition has been kept constant using He-3 bleed throughout the ICRF phase with a typical duration of 4-6 s, i.e. 15-40 energy confinement times. Using waves propagating...

  16. Enhanced Forced Convection Heat Transfer using Small Scale Vorticity Concentrations Effected by Flow Driven, Aeroelastically Vibrating Reeds

    Science.gov (United States)

    2016-08-03

    lines). b) For the infinite reed case, a sinusoidal body is shown (thick black line) with images (solid and dashed gray lines). DISTRIBUTION A...ratio of the mean heat transfer through the output plane of a channel with the reed ?̅? to the mean heat transfer through the output plane of a...the flow. This is remarkable, because it means that energy from smaller scales (higher frequencies) is transferred to the lower frequencies within

  17. Vibrational Action Spectroscopy of Solids: New Surface-Sensitive Technique

    Science.gov (United States)

    Wu, Zongfang; Płucienik, Agata; Feiten, Felix E.; Naschitzki, Matthias; Wachsmann, Walter; Gewinner, Sandy; Schöllkopf, Wieland; Staemmler, Volker; Kuhlenbeck, Helmut; Freund, Hans-Joachim

    2017-09-01

    Vibrational action spectroscopy employing infrared radiation from a free-electron laser has been successfully used for many years to study the vibrational and structural properties of gas phase aggregates. Despite the high sensitivity of this method no relevant studies have yet been conducted for solid sample surfaces. We have set up an experiment for the application of this method to such targets, using infrared light from the free-electron laser of the Fritz Haber Institute. In this Letter, we present first results of this technique with adsorbed argon and neon atoms as messengers. We were able to detect surface-located vibrations of a thin V2O3(0 0 0 1 ) film on Au(111) as well as adsorbate vibrations, demonstrating that this method is highly surface sensitive. We consider that the dominant channel for desorption of the messenger atoms is direct inharmonic vibrational coupling, which is essentially insensitive to subsurface or bulk vibrations. Another channel is thermal desorption due to sample heating by absorption of infrared light. The high surface sensitivity of the nonthermal channel and its insensitivity to subsurface modes makes this technique an ideal tool for the study of surface-located vibrations.

  18. Numerical Study of the Dynamic Response of Heat and Mass Transfer to Operation Mode Switching of a Unitized Regenerative Fuel Cell

    Directory of Open Access Journals (Sweden)

    Hong Xiao

    2016-12-01

    Full Text Available Knowledge concerning the complicated changes of mass and heat transfer is desired to improve the performance and durability of unitized regenerative fuel cells (URFCs. In this study, a transient, non-isothermal, single-phase, and multi-physics mathematical model for a URFC based on the proton exchange membrane is generated to investigate transient responses in the process of operation mode switching from fuel cell (FC to electrolysis cell (EC. Various heat generation mechanisms, including Joule heat, reaction heat, and the heat attributed to activation polarizations, have been considered in the transient model coupled with electrochemical reaction and mass transfer in porous electrodes. The polarization curves of the steady-state models are validated by experimental data in the literatures. Numerical results reveal that current density, gas mass fractions, and temperature suddenly change with the sudden change of operating voltage in the mode switching process. The response time of temperature is longer than that of current density and gas mass fractions. In both FC and EC modes, the cell temperature and gradient of gas mass fraction in the oxygen side are larger than that in the hydrogen side. The temperature difference of the entire cell is less than 1.5 K. The highest temperature appears at oxygen-side catalyst layer under the FC mode and at membrane under a more stable EC mode. The cell is exothermic all the time. These dynamic responses and phenomena have important implications for heat analysis and provide proven guidelines for the improvement of URFCs mode switching.

  19. Vibrations of rotating machinery

    CERN Document Server

    Matsushita, Osami; Kanki, Hiroshi; Kobayashi, Masao; Keogh, Patrick

    2017-01-01

    This book opens with an explanation of the vibrations of a single degree-of-freedom (dof) system for all beginners. Subsequently, vibration analysis of multi-dof systems is explained by modal analysis. Mode synthesis modeling is then introduced for system reduction, which aids understanding in a simplified manner of how complicated rotors behave. Rotor balancing techniques are offered for rigid and flexible rotors through several examples. Consideration of gyroscopic influences on the rotordynamics is then provided and vibration evaluation of a rotor-bearing system is emphasized in terms of forward and backward whirl rotor motions through eigenvalue (natural frequency and damping ratio) analysis. In addition to these rotordynamics concerning rotating shaft vibration measured in a stationary reference frame, blade vibrations are analyzed with Coriolis forces expressed in a rotating reference frame. Other phenomena that may be assessed in stationary and rotating reference frames include stability characteristic...

  20. Structural Stability and Vibration

    DEFF Research Database (Denmark)

    Wiggers, Sine Leergaard; Pedersen, Pauli

    This book offers an integrated introduction to the topic of stability and vibration. Strikingly, it describes stability as a function of boundary conditions and eigenfrequency as a function of both boundary conditions and column force. Based on a post graduate course held by the author at the Uni......This book offers an integrated introduction to the topic of stability and vibration. Strikingly, it describes stability as a function of boundary conditions and eigenfrequency as a function of both boundary conditions and column force. Based on a post graduate course held by the author...... and their derivation, thus stimulating them to write interactive and dynamic programs to analyze instability and vibrational modes....

  1. A vibrational spectroscopic study of structure evolution of water dissolved in supercritical carbon dioxide under isobaric heating.

    Science.gov (United States)

    Oparin, R; Tassaing, T; Danten, Y; Besnard, M

    2004-06-08

    A combination of Raman scattering spectroscopy and infrared absorption was applied to investigate the structural evolution of water dissolved in supercritical carbon dioxide under isobaric heating (T=40-340 degrees C, P=250 bar). Quantitative analysis of experimental spectra allowed us to determine that at relatively moderate temperatures water dissolved in CO(2)-rich phase exists only under monomeric form (solitary water surrounding by CO(2) molecules), but hydrogen-bonded species, namely, dimers, begin to appear upon heating. At the same time, the ratio of dimers to monomers concentration increases with further temperature increase and at temperatures close to the temperature of total miscibility of the mixture (T=366 degrees C, P=250 bar), water dimers only are present in the CO(2)-rich phase. (c) 2004 American Institute of Physics.

  2. Generation of Non-Inductive H-Mode Plasmas with 30 MHz Fast Wave Heating in NSTX-U

    Science.gov (United States)

    Taylor, G.; Bertelli, N.; Gerhardt, S. P.; Hosea, J. C.; Mueller, D.; Perkins, R. J.; Poli, F. M.; Wilson, J. R.; Raman, R.

    2016-10-01

    A Fusion Nuclear Science Facility based on a spherical tokamak must generate the plasma current (Ip) with little or no central solenoid field. The NSTX-U non-inductive (NI) plasma research program is addressing this goal by developing NI start-up, ramp-up and sustainment scenarios separately. 4 MW of 30 MHz fast wave power is predicted to ramp Ip to 400 kA, a level sufficient to avoid significant shine-through of 90 keV ions from neutral beam injection. In 2010, experiments in NSTX demonstrated that 1.4 MW of 30 MHz high-harmonic fast wave (HHFW) power could generate an Ip = 300 kA H-mode discharge with a NI Ip fraction, fNI, around 0.7 at the maximum axial toroidal field (BT(0)) in NSTX of 0.55 T. NSTX-U is a major upgrade of NSTX that will eventually allow the generation of plasmas with BT(0) up to 1 T. Full wave simulations of 30 MHz HHFW heating in NSTX-U predict reduced FW power loss in the plasma edge as BT(0) is increased. HHFW experiments this year aim to couple 3 - 4 MW of 30 MHz HHFW power into an Ip = 250 - 350 kA plasma with BT(0) up to 0.75 T to generate a fNI = 1 H-mode plasma. These experiments should benefit from the improved fast wave coupling predicted at higher BT(0) in NSTX-U. Work supported by USDOE Contract No. DE-AC02-09CH11466.

  3. Improved methods for Feynman path integral calculations and their application to calculate converged vibrational-rotational partition functions, free energies, enthalpies, entropies, and heat capacities for methane.

    Science.gov (United States)

    Mielke, Steven L; Truhlar, Donald G

    2015-01-28

    We present an improved version of our "path-by-path" enhanced same path extrapolation scheme for Feynman path integral (FPI) calculations that permits rapid convergence with discretization errors ranging from O(P(-6)) to O(P(-12)), where P is the number of path discretization points. We also present two extensions of our importance sampling and stratified sampling schemes for calculating vibrational-rotational partition functions by the FPI method. The first is the use of importance functions for dihedral angles between sets of generalized Jacobi coordinate vectors. The second is an extension of our stratification scheme to allow some strata to be defined based only on coordinate information while other strata are defined based on both the geometry and the energy of the centroid of the Feynman path. These enhanced methods are applied to calculate converged partition functions by FPI methods, and these results are compared to ones obtained earlier by vibrational configuration interaction (VCI) calculations, both calculations being for the Jordan-Gilbert potential energy surface. The earlier VCI calculations are found to agree well (within ∼1.5%) with the new benchmarks. The FPI partition functions presented here are estimated to be converged to within a 2σ statistical uncertainty of between 0.04% and 0.07% for the given potential energy surface for temperatures in the range 300-3000 K and are the most accurately converged partition functions for a given potential energy surface for any molecule with five or more atoms. We also tabulate free energies, enthalpies, entropies, and heat capacities.

  4. Comparison of the Calculations Results of Heat Exchange Between a Single-Family Building and the Ground Obtained with the Quasi-Stationary and 3-D Transient Models. Part 2: Intermittent and Reduced Heating Mode

    Science.gov (United States)

    Staszczuk, Anna

    2017-03-01

    The paper provides comparative results of calculations of heat exchange between ground and typical residential buildings using simplified (quasi-stationary) and more accurate (transient, three-dimensional) methods. Such characteristics as building's geometry, basement hollow and construction of ground touching assemblies were considered including intermittent and reduced heating mode. The calculations with simplified methods were conducted in accordance with currently valid norm: PN-EN ISO 13370:2008. Thermal performance of buildings. Heat transfer via the ground. Calculation methods. Comparative estimates concerning transient, 3-D, heat flow were performed with computer software WUFI®plus. The differences of heat exchange obtained using more exact and simplified methods have been specified as a result of the analysis.

  5. Time-Dependent Simulations of Fast-Wave Heated High-Non-Inductive-Fraction H-Mode Plasmas in the National Spherical Torus Experiment Upgrade

    Science.gov (United States)

    Taylor, Gary; Bertelli, Nicola; Gerhardt, Stefan P.; Hosea, Joel C.; Mueller, Dennis; Perkins, Rory J.; Poli, Francesca M.; Wilson, James R.; Raman, Roger

    2017-10-01

    30 MHz fast-wave heating may be an effective tool for non-inductively ramping low-current plasmas to a level suitable for initiating up to 12 MW of neutral beam injection on the National Spherical Tokamak Experiment Upgrade (NSTX-U). Previously on NSTX 30 MHz fast wave heating was shown to efficiently and rapidly heat electrons; at the NSTX maximum axial toroidal magnetic field (BT(0)) of 0.55 T, 1.4 MW of 30 MHz heating increased the central electron temperature from 0.2 to 2 keV in 30 ms and generated an H-mode plasma with a non-inductive fraction (fNI) ˜ 0.7 at a plasma current (Ip) of 300 kA. NSTX-U will operate at BT(0) up to 1 T, with up to 4 MW of 30 MHz power (Prf). Predictive TRANSP free boundary transport simulations, using the TORIC full wave spectral code to calculate the fast-wave heating and current drive, have been run for NSTX-U Ip = 300 kA H-mode plasmas. Favorable scaling of fNI with 30 MHz heating power is predicted, with fNI ≥ 1 for Prf ≥ 2 MW.

  6. Determination of susceptibility and specific heat critical exponents for weak itinerant-electron ferromagnets from vibrating reed experiments

    Science.gov (United States)

    Balakrishnan, K.; Kaul, S. N.

    2002-04-01

    We report the observation of a linear relationship between the magnetic contribution to Young's modulus, ΔE/E0, and inverse magnetic susceptibility χ-1 for amorphous weak itinerant-electron ferromagnets Fe90Zr10 and Fe91Zr9 in the asymptotic critical region near the ferromagnetic-paramagnetic phase transition. The proportionality ΔE(T)/E0~χ-1(T) is shown to provide as accurate a means of determining the asymptotic critical exponent γ and the leading ``correction-to-scaling'' amplitudes for susceptibilty from the ΔE/E0 data as a direct measurement of magnetic susceptibilty does. Similarly, the well-known relation between the magnetic contributions to sound velocity and specific heat is fully exploited to extract accurate estimates for the universal critical amplitude ratio A+/A- and the asymptotic critical exponents α+/- for the specific heat from the sound velocity data. The presently determined values of α+/- and γ, together with the reported value for spontaneous magnetization critical exponent β, not only obey the scaling equalities α+=α- and α+2β+γ=2 but also assert that the atomic magnetic moments in the alloys in question interact with one another through an attractive interaction which decays faster than 1/r5 with the interatomic spacing, r.

  7. Active noise control of a vibrating surface: Continuum and non-continuum investigations on vibroacoustic sound reduction by a secondary heat-flux source

    Science.gov (United States)

    Manela, A.; Pogorelyuk, L.

    2015-12-01

    We study the effect of surface heating on sound radiation by a vibrating boundary. Focusing on a setup of an infinite planar wall interacting with a semi-infinite expanse of a gas, the system response to arbitrary (small-amplitude) vibro-thermal excitation is investigated. Starting with the case of sinusoidal actuations, the superposed effect of boundary heat-flux excitation at a common frequency ω is examined. The entire range of frequencies is considered, where, depending on the ratio between ω and gas kinetic collision frequency ωcoll, fundamentally different flow regimes follow. The two limit cases of ω ≪ωcoll (continuum-flow conditions) and ω ≫ωcoll (ballistic flow regime) are investigated analytically, based on continuum equations and collisionless Boltzmann equation, respectively. In between, an intermediate interval of frequencies ω ~ωcoll is analyzed numerically, based on the direct simulation Monte Carlo method. In search for optimal conditions for acoustic sound reduction, it is found that effective attenuation is obtained when boundary heat flux is applied at opposite phase to surface actuation. Amplitude-wise, conditions for minimization of the acoustic field vary between the limits: at low-frequency conditions, wave radiation extends over large distances from the wall, and optimal sound reduction is achieved when the ratio between wall-inserted thermal and kinetic energies |Eq/Ek|opt equals γ /(γ - 1) (with γ denoting the ratio between gas specific heat capacities). At high-frequency conditions, wall signal affects only a thin gas layer (of the order of the mean free path) in the vicinity of the boundary, and optimal attenuation is achieved when |Eq/Ek|opt = 1. The analysis is extended to consider the system response to non-periodic excitations, for the specific case of a delta-function input. Making use of the above collisionless- and continuum-limit analyses, early- and late-time system responses are computed. While conditions for

  8. Study of the Impact of Heat Treatment Modes on Formation of Microstructure and a Given Set of Mechanical Properties of High-Strength Flat Products with Guaranteed Hardness (400 to 450 HB) from Low-Alloyed Steel

    Science.gov (United States)

    Matrosov, M. Yu; Martynov, P. G.; Goroshko, T. V.; Zvereva, M. I.; Mitrofanov, A. V.; Barabash, K. Yu

    2017-12-01

    The results of the study of influence of heat treatment modes on microstructure, size and shape of grains, mechanical properties of high-strength flat products from low-alloyed C-Mn-Cr-Si-Mo steel microalloyed by boron are presented. Heat treatment modes, which provide a combination of high impact viscosity at negative temperatures and guaranteed hardness, are determined.

  9. Compact integrated piezoelectric vibration control package

    Science.gov (United States)

    Spangler, Ronald L., Jr.; Russo, Farla M.; Palombo, Daniel A.

    1997-06-01

    Using recent advances in small, surface-mount electronics, coupled with proprietary packaging techniques, ACX has developed the SmartPackTM. The design and realization of this self-contained, active piezoelectric control device are described in this paper. The SmartPack uses a local control architecture, consisting of two parallel, analog, positive position feedback (PPF) filters, along with nearly collocated piezo strain sensors and actuators, to control multiple structural vibration modes. A key issue is the management of waste heat from the power electronics required to drive the piezo actuators. This issue is addressed through thermal/electrical modeling of the packaged amplifier. The effectiveness of the device is demonstrated through multi-mode active damping on a 24 inch square plate.

  10. Heat

    CERN Document Server

    Lawrence, Ellen

    2016-01-01

    Is it possible to make heat by rubbing your hands together? Why does an ice cube melt when you hold it? In this title, students will conduct experiments to help them understand what heat is. Kids will also investigate concepts such as which materials are good at conducting heat and which are the best insulators. Using everyday items that can easily be found around the house, students will transform into scientists as they carry out step-by-step experiments to answer interesting questions. Along the way, children will pick up important scientific skills. Heat includes seven experiments with detailed, age-appropriate instructions, surprising facts and background information, a "conclusions" section to pull all the concepts in the book together, and a glossary of science words. Colorful, dynamic designs and images truly put the FUN into FUN-damental Experiments.

  11. Coupled thermal, structural and vibrational analysis of a hypersonic engine for flight test

    Energy Technology Data Exchange (ETDEWEB)

    Sook-Ying, Ho [Defence Science and Technology Organisation, SA (Australia); Paull, A. [Queensland Univ., Dept. of Mechanical Engineering (Australia)

    2006-07-15

    This paper describes a relatively simple and quick method for implementing aerodynamic heating models into a finite element code for non-linear transient thermal-structural and thermal-structural-vibrational analyses of a Mach 10 generic HyShot scram-jet engine. The thermal-structural-vibrational response of the engine was studied for the descent trajectory from 60 to 26 km. Aerodynamic heating fluxes, as a function of spatial position and time for varying trajectory points, were implemented in the transient heat analysis. Additionally, the combined effect of varying dynamic pressure and thermal loads with altitude was considered. This aero-thermal-structural analysis capability was used to assess the temperature distribution, engine geometry distortion and yielding of the structural material due to aerodynamic heating during the descent trajectory, and for optimising the wall thickness, nose radius of leading edge, etc. of the engine intake. A structural vibration analysis was also performed following the aero-thermal-structural analysis to determine the changes in natural frequencies of the structural vibration modes that occur at the various temperatures associated with the descent trajectory. This analysis provides a unique and relatively simple design strategy for predicting and mitigating the thermal-structural-vibrational response of hypersonic engines. (authors)

  12. Resonant vibration control of rotating beams

    DEFF Research Database (Denmark)

    Svendsen, Martin Nymann; Krenk, Steen; Høgsberg, Jan Becker

    2011-01-01

    Rotatingstructures,like e.g.wind turbine blades, may be prone to vibrations associated with particular modes of vibration. It is demonstrated, how this type of vibrations can be reduced by using a collocated sensor–actuator system, governed by a resonant controller. The theory is here demonstrated...... modal connectivity, only very limited modal spill-over is generated. The controller acts by resonance and therefore has only a moderate energy consumption, and successfully reduces modal vibrations at the resonance frequency....

  13. Vibration Attenuation of Plate Using Multiple Vibration Absorbers

    Directory of Open Access Journals (Sweden)

    Zaman Izzuddin

    2014-07-01

    Full Text Available Vibrations are undesired phenomenon and it can cause harm, distress and unsettling influence to the systems or structures, for example, aircraft, automobile, machinery and building. One of the approach to limit this vibration by introducing passive vibration absorber attached to the structure. In this paper, the adequacy of utilizing passive vibration absorbers are investigated. The vibration absorber system is designed to minimize the vibration of a thin plate fixed along edges. The plate’s vibration characteristics, such as, natural frequency and mode shape are determined using three techniques: theoretical equations, finite element (FE analysis and experiment. The results demonstrate that the first four natural frequencies of fixed-fixed ends plate are 48, 121, 193 and 242 Hz, and these results are corroborated well with theoretical, FE simulation and experiment. The experiment work is further carried out with attached single and multiple vibration absorbers onto plate by tuning the absorber’s frequency to match with the excitation frequency. The outcomes depict that multiple vibration absorbers are more viable in lessening the global structural vibration.

  14. Analysis of vibrational-translational energy transfer using the direct simulation Monte Carlo method

    Science.gov (United States)

    Boyd, Iain D.

    1991-01-01

    A new model is proposed for energy transfer between the vibrational and translational modes for use in the direct simulation Monte Carlo method (DSMC). The model modifies the Landau-Teller theory for a harmonic oscillator and the rate transition is related to an experimental correlation for the vibrational relaxation time. Assessment of the model is made with respect to three different computations: relaxation in a heat bath, a one-dimensional shock wave, and hypersonic flow over a two-dimensional wedge. These studies verify that the model achieves detailed balance, and excellent agreement with experimental data is obtained in the shock wave calculation. The wedge flow computation reveals that the usual phenomenological method for simulating vibrational nonequilibrium in the DSMC technique predicts much higher vibrational temperatures in the wake region.

  15. Vibrational spectroscopy of resveratrol

    Science.gov (United States)

    Billes, Ferenc; Mohammed-Ziegler, Ildikó; Mikosch, Hans; Tyihák, Ernő

    2007-11-01

    In this article the authors deal with the experimental and theoretical interpretation of the vibrational spectra of trans-resveratrol (3,5,4'-trihydroxy- trans-stilbene) of diverse beneficial biological activity. Infrared and Raman spectra of the compound were recorded; density functional calculations were carried out resulting in the optimized geometry and several properties of the molecule. Based on the calculated force constants, a normal coordinate analysis yielded the character of the vibrational modes and the assignment of the measured spectral bands.

  16. Vibrational Relaxation in Neat Crystals of Naphthalene by Picosecond CARS

    NARCIS (Netherlands)

    Hesp, Ben H.; Wiersma, Douwe A.

    1980-01-01

    Picosecond delayed CARS experiments on totally symmetric modes in naphthalene at 1.5 K are reported. The Raman lineshape of the vibrational excitons is lorentzian and vibrational relaxation can be surprisingly slow. The Raman lineshape of the Ag exciton level of the 766 cm-1 vibrational mode reveals

  17. Macrocycle and substituent vibrational modes of nonplanar nickel (II) octaethyltetraphenylporphyrin from its resonance Raman, near-infrared-excited FT Raman, and FT-IR spectra and deuterium isotope shifts

    Energy Technology Data Exchange (ETDEWEB)

    Stichternath, A.; Schweitzer-Stenner, R.; Dreybrodt, W. (Univ. of Bremen (Germany)); Mak, R.S.W.; Li, X.Y. (Hong Kong Univ. of Science and Technology (Hong Kong)); Sparks, L.D.; Shelnutt, J.A. (Sandia National Lab., Albuquerque, NM (United States) Univ. of New Mexico, Albuquerque (United States)); Medforth, C.J.; Smith, K.M. (Univ. of California, Davis (United States))

    1993-04-15

    We have employed Raman dispersion, FT Raman, and FT-IR spectroscopy to identify a large number of resonance Raman lines of Ni(II) octaethyltetraphenylporphyrin dissolved in CS[sub 2]. The Raman depolarization dispersion technique was used to derive the symmetry of the normal modes giving rise to the observed Raman lines. By combining this information and the already available normal coordinates of Ni(II) tetraphenylporphyrin and Ni(II) octaethylporphyrin, many of the Raman-modes of the macrocycle could be assigned. Some resonance-enhanced Raman lines were found to arise from vibrations of the ethyl and phenyl substituents. They were identified by comparing resonance Raman, FT Raman, and FT infrared spectra of the Ni(II) octaethyltetraphenylporphyrin and its d[sub 20] isotopomer. All Raman lines normally referred to as core-size markers are found to be significantly shifted to lower frequencies with respect to their positions in Ni(II) octaethylporphyrin, in accordance with earlier findings (Shelnutt et al., J. Am. Chem. Soc. 113, 4077, 1991). This suggests that the molecule is in a highly nonplanar conformation. This notion is further corroborated by the strong dispersion of the depolarization ratio observed for nearly all A[sub 1g] and A[sub 2g] modes of the macrocycle. 27 refs., 13 figs., 2 tabs.

  18. Multiple Rabi Splittings under Ultrastrong Vibrational Coupling.

    Science.gov (United States)

    George, Jino; Chervy, Thibault; Shalabney, Atef; Devaux, Eloïse; Hiura, Hidefumi; Genet, Cyriaque; Ebbesen, Thomas W

    2016-10-07

    From the high vibrational dipolar strength offered by molecular liquids, we demonstrate that a molecular vibration can be ultrastrongly coupled to multiple IR cavity modes, with Rabi splittings reaching 24% of the vibration frequencies. As a proof of the ultrastrong coupling regime, our experimental data unambiguously reveal the contributions to the polaritonic dynamics coming from the antiresonant terms in the interaction energy and from the dipolar self-energy of the molecular vibrations themselves. In particular, we measure the opening of a genuine vibrational polaritonic band gap of ca. 60 meV. We also demonstrate that the multimode splitting effect defines a whole vibrational ladder of heavy polaritonic states perfectly resolved. These findings reveal the broad possibilities in the vibrational ultrastrong coupling regime which impact both the optical and the molecular properties of such coupled systems, in particular, in the context of mode-selective chemistry.

  19. Alleviation of Buffet-Induced Vibration Using Piezoelectric Actuators

    National Research Council Canada - National Science Library

    Morgenstern, Shawn D

    2006-01-01

    .... The objective of this research was to determine the most critical natural modes of vibration for the F-16 ventral fin and design piezoelectric actuators capable of reducing buffet-induced ventral fin vibration...

  20. Non-local heat transport, rotation reversals and up/down impurity density asymmetries in Alcator C-Mod ohmic L-mode plasmas

    Science.gov (United States)

    Rice, J. E.; Gao, C.; Reinke, M. L.; Diamond, P. H.; Howard, N. T.; Sun, H. J.; Cziegler, I.; Hubbard, A. E.; Podpaly, Y. A.; Rowan, W. L.; Terry, J. L.; Chilenski, M. A.; Delgado-Aparicio, L.; Ennever, P. C.; Ernst, D.; Greenwald, M. J.; Hughes, J. W.; Ma, Y.; Marmar, E. S.; Porkolab, M.; White, A. E.; Wolfe, S. M.

    2013-03-01

    Several seemingly unrelated effects in Alcator C-Mod ohmic L-mode plasmas are shown to be closely connected: non-local heat transport, core toroidal rotation reversals, energy confinement saturation and up/down impurity density asymmetries. These phenomena all abruptly transform at a critical value of the collisionality. At low densities in the linear ohmic confinement regime, with collisionality ν* ⩽ 0.35 (evaluated inside of the q = 3/2 surface), heat transport exhibits non-local behaviour, core toroidal rotation is directed co-current, edge impurity density profiles are up/down symmetric and a turbulent feature in core density fluctuations with kθ up to 15 cm-1 (kθρs ˜ 1) is present. At high density/collisionality with saturated ohmic confinement, electron thermal transport is diffusive, core rotation is in the counter-current direction, edge impurity density profiles are up/down asymmetric and the high kθ turbulent feature is absent. The rotation reversal stagnation point (just inside of the q = 3/2 surface) coincides with the non-local electron temperature profile inversion radius. All of these observations suggest a possible unification in a model with trapped electron mode prevalence at low collisionality and ion temperature gradient mode domination at high collisionality.

  1. Analytical and experimental studies of natural vibrations modes of ring-stiffened truncated-cone shells with variable theoretical ring fixity

    Science.gov (United States)

    Naumann, E. C.; Catherines, D. S.; Walton, W. C., Jr.

    1971-01-01

    Experimental and analytical investigations of the vibratory behavior of ring-stiffened truncated-cone shells are described. Vibration tests were conducted on 60 deg conical shells having up to four ring stiffeners and for free-free and clamped-free edge constraints and 9 deg conical shells, for two thicknesses, each with two angle rings and for free-free, free-clamped, and clamped-clamped edge constraints. The analytical method is based on linear thin shell theory, employing the Rayleigh-Ritz method. Discrete rings are represented as composed of one or more segments, each of which is a short truncated-cone shell of uniform thickness. Equations of constraint are used to join a ring and shell along a circumferential line connection. Excellent agreement was obtained for comparisons of experimental and calculated frequencies.

  2. The Soleil View on Prototypical Organic Nitriles: Selected Vibrational Modes of Ethyl Cyanide, C_2H_5CN, and Spectroscopic Analysis Using AN Automated Spectral Assignment Procedure (asap)

    Science.gov (United States)

    Endres, Christian; Caselli, Paola; Martin-Drumel, Marie-Aline; McCarthy, Michael C.; Pirali, Olivier; Wehres, Nadine; Schlemmer, Stephan; Thorwirth, Sven

    2016-06-01

    Vibrational spectra of small organic nitriles, propionitrile and n-butyronitrile, have been investigated at high spectral resolution at the French national synchroton facility SOLEIL using Fourier-transform far-infrared spectroscopy (< 700 cm-1). The Automated Spectral Assignment Procedure (ASAP) has been used for line assignement and accurate determination of rotational level energies, in particular, of the ν20=1 and the ν12=1 states of propionitrile. The analysis does not only confirm the applicability of the ASAP in the treatment of (dense) high-resolution infrared spectra but also reveals some of its limitations which will be discussed in some detail. M. A. Martin-Drumel, C. P. Endres, O. Zingsheim, T. Salomon, J. van Wijngaarden, O. Pirali, S. Gruet, F. Lewen, S. Schlemmer, M. C. McCarthy, and S. Thorwirth 2015, J. Mol. Spectrosc. 315, 72

  3. Microbubble Surface Modes

    NARCIS (Netherlands)

    Versluis, Michel; Palanchon, P.; Goertz, D.; van der Meer, S.M.; Chin, C.T.; Lohse, Detlef; de Jong, N.

    2004-01-01

    We have investigated surface vibrations generated by ultrasound excitation of individual unencapsulated micron-sized bubbles. In addition, we present surface modes (n=2 and 3) observed for phospholipid-coated ultrasound contrast agents excited through excitation of radial modes at frequencies

  4. Blade Vibration Measurement System

    Science.gov (United States)

    Platt, Michael J.

    2014-01-01

    The Phase I project successfully demonstrated that an advanced noncontacting stress measurement system (NSMS) could improve classification of blade vibration response in terms of mistuning and closely spaced modes. The Phase II work confirmed the microwave sensor design process, modified the sensor so it is compatible as an upgrade to existing NSMS, and improved and finalized the NSMS software. The result will be stand-alone radar/tip timing radar signal conditioning for current conventional NSMS users (as an upgrade) and new users. The hybrid system will use frequency data and relative mode vibration levels from the radar sensor to provide substantially superior capabilities over current blade-vibration measurement technology. This frequency data, coupled with a reduced number of tip timing probes, will result in a system capable of detecting complex blade vibrations that would confound traditional NSMS systems. The hardware and software package was validated on a compressor rig at Mechanical Solutions, Inc. (MSI). Finally, the hybrid radar/tip timing NSMS software package and associated sensor hardware will be installed for use in the NASA Glenn spin pit test facility.

  5. Page 1 The Specific Heats of Crystals—II 161 different techniques. It ...

    Indian Academy of Sciences (India)

    different techniques. It is a simple matter with the aid of the table to cal- culate the contributions to the specific heat arising from the nine modes of internal vibration of the diamond structure. The lowest frequency appearing in the table expressed in wave-numbers, viz., 621 cm." may also be properly assumed to be the upper ...

  6. Large electron transfer rate effects from the Duschinsky mixing of vibrations

    DEFF Research Database (Denmark)

    Sando, Gerald M.; Spears, Kenneth G; Hupp, Joseph T

    2001-01-01

    vibrations are very important. The Duschinsky effect arises when two electronic states have vibrational normal mode coordinate systems that are rotated and translated relative to each other. We use a conventional quantum rate model for ET, and the examples include 6-8 vibrations, where two vibrational modes...

  7. Smart accelerometer. [vibration damage detection

    Science.gov (United States)

    Bozeman, Richard J., Jr. (Inventor)

    1994-01-01

    The invention discloses methods and apparatus for detecting vibrations from machines which indicate an impending malfunction for the purpose of preventing additional damage and allowing for an orderly shutdown or a change in mode of operation. The method and apparatus is especially suited for reliable operation in providing thruster control data concerning unstable vibration in an electrical environment which is typically noisy and in which unrecognized ground loops may exist.

  8. Ion cyclotron range of frequencies mode conversion electron heating in deuterium-hydrogen plasmas in the Alcator C-Mod tokamak

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Y [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Wukitch, S J [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Bonoli, P T [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Marmar, E [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Mossessian, D [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Nelson-Melby, E [Centre de Recherches en Physique des Plasmas, Association EURATOM - Confederation Suisse, Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland); Phillips, P [Fusion Research Center, University of Texas, Austin, Texas 78712 (United States); Porkolab, M [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Schilling, G [Plasma Physics Laboratory, Princeton, NJ 08543 (United States); Wolfe, S [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Wright, J [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States)

    2003-06-01

    Localized direct electron heating (EH) by mode-converted (MC) ion cyclotron range of frequencies (ICRF) waves in D(H) tokamak plasmas has been clearly observed for the first time in Alcator C-Mod. Both on- and off-axis (high field side) mode conversion EH (MCEH) have been observed. The MCEH profile was obtained from a break-in-slope analysis of electron temperature signals in the presence of radio frequency shut-off. The temperature was measured by a 32-channel high spatial resolution ({<=}7 mm) 2nd harmonic heterodyne electron cyclotron emission system. The experimental profiles were compared with the predictions from a toroidal full-wave ICRF code TORIC. Using the hydrogen concentration measured by a high-resolution optical spectrometer, TORIC predictions were shown qualitatively in agreement with the experimental results for both on- and off-axis MC cases. From the simulations, the EH from MC ion cyclotron wave and ion Bernstein wave is examined.

  9. The role of parallel heat transport in the relation between upstream scrape-off layer widths and target heat flux width in H-mode plasmas of NSTX.

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, J W; Boedo, J A; Maingi, R; Soukhanovskii, V A

    2009-01-05

    The physics of parallel heat transport was tested in the Scrape-off Layer (SOL) plasma of the National Spherical Torus Experiment (NSTX) [M. Ono, et al., Nucl. Fusion 40, 557 (2000) and S. M. Kaye, et al., Nucl. Fusion 45, S168 (2005)] tokamak by comparing the upstream electron temperature (T{sub e}) and density (n{sub e}) profiles measured by the mid-plane reciprocating probe to the heat flux (q{sub {perpendicular}}) profile at the divertor plate measured by an infrared (IR) camera. It is found that electron conduction explains the near SOL width data reasonably well while the far SOL, which is in the sheath limited regime, requires an ion heat flux profile broader than the electron one to be consistent with the experimental data. The measured plasma parameters indicate that the SOL energy transport should be in the conduction-limited regime for R-R{sub sep} (radial distance from the separatrix location) < 2-3 cm. The SOL energy transport should transition to the sheath-limited regime for R-R{sub sep} > 2-3cm. The T{sub e}, n{sub e}, and q{sub {perpendicular}} profiles are better described by an offset exponential function instead of a simple exponential. The conventional relation between mid plane electron temperature decay length ({lambda}{sub Te}) and target heat flux decay length ({lambda}{sub q}) is {lambda}{sub Te} = 7/2{lambda}{sub q}, whereas the newly-derived relation, assuming offset exponential functional forms, implies {lambda}{sub Te} = (2-2.5){lambda}{sub q}. The measured values of {lambda}{sub Te}/{lambda}{sub q} differ from the new prediction by 25-30%. The measured {lambda}{sub q} values in the far SOL (R-R{sub sep} > 2-3cm) are 9-10cm, while the expected values are 2.7 < {lambda}{sub q} < 4.9 cm (for sheath-limited regime). We propose that the ion heat flux profile is substantially broader than the electron heat flux profile as an explanation for this discrepancy in the far SOL.

  10. Experimental Studies of the Collisional Excitation of Infrared Active Vibrational Stretch Modes in CO2 and H2O with an Intersecting, Hyperthermal Molecular Beam Apparatus. Volume 1

    Science.gov (United States)

    1975-02-01

    thoumgh the pinhole into the diverging -:tine bhown in Fig. 4 and then on into the coiicon chai her. The remaining flow is pumped out through an anular ...molecules are prepared under single collision conditions in opposed high velocity flows , one of which contains H20 or CO2 while the other contains a...molecular collision partner. Hyperthermal vclocity flows are required since the threshold activation energy of the 11 0 and CO V modes are 0. 466 and

  11. Direct observation of electron-Bernstein wave heating by O-X-B-mode conversion at low magnetic field in the WEGA stellarator.

    Science.gov (United States)

    Podoba, Y Y; Laqua, H P; Warr, G B; Schubert, M; Otte, M; Marsen, S; Wagner, F; Holzhauer, E

    2007-06-22

    The ordinary-extraordinary-Bernstein-mode conversion process for overdense plasma heating with electron-Bernstein waves is demonstrated in the WEGA stellarator at low magnetic field (approximately 50 mT) at 2.45 GHz. For the first time the conversion from an O wave to an X wave is clearly demonstrated by probe measurements of amplitude and phase of the wave field in the conversion region and supported by two-dimensional full-wave calculations. The propagation and resonant absorption of the Bernstein wave is measured in fast power modulation experiments.

  12. Performance in cooling mode of a heat pump using panels with PV cells as the condenser; Taiyo denchitsuki panel wo gyoshukuki to shita heat pump no reibo unten

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, T.; Ito, S.; Miura, N. [Kanagawa Institute of Technology, Kanagawa (Japan); Fujita, M. [Chubu Electric Power Co. Inc., Nagoya (Japan)

    1996-10-27

    Comparison was made between heat pumps in cooling operation, one having two panels provided with solar cells, the second having an air-cooled heat exchanger alone, and the third having a series connection of a panel unit and air-cooled heat exchanger, all serving as condenser. The results are shown below. In the case of two-panel-unit condenser, there is a difference ({Delta}t) of 15{degree}C between the daytime free air temperature and condensing temperature but, with decreased insolation, free air temperature, and wind speed in the evening, the {Delta}t lowered to approximately 8{degree}C while the COP (coefficient of performance) increased from 2.4 to 3.3. On a cloudy day in summer, the two-panel-unit condenser had a {Delta}t of 13.9{degree}C and a COP of 3.1. In the case of the series-connection condenser, the {Delta}t was approximately 8{degree}C and the COP was 3.5. The COP of the two-panel-unit condenser was lower than that of the air-cooled heat exchanger by 9% at an insolation of 442W/m{sup 2} but it rose to 12% in the absence of insolation. The COP of the two-panel-unit condenser was higher than that of a one-panel-unit condenser by 17%. When an insulator plate was attached to the back of a panel, the {Delta}t increased but the COP decreased by 14%. In the case of the series-connection condenser, the COP increased by 6% in the absence of the insulator plate. 2 refs., 9 figs.

  13. Performance analysis of a two-state quantum heat engine working with a single-mode radiation field in a cavity.

    Science.gov (United States)

    Wang, Jianhui; He, Jizhou; He, Xian

    2011-10-01

    We present a performance analysis of a two-state heat engine model working with a single-mode radiation field in a cavity. The heat engine cycle consists of two adiabatic and two isoenergetic processes. Assuming the wall of the potential moves at a very slow speed, we determine the optimization region and the positive work condition of the heat engine model. Furthermore, we generalize the results to the performance optimization for a two-state heat engine with a one-dimensional power-law potential. Based on the generalized model with an arbitrary one-dimensional potential, we obtain the expression of efficiency as η=1-E(C)/E(H), with E(H) (E(C)) denoting the expectation value of the system Hamiltonian along the isoenergetic process at high (low) energy. This expression is an analog of the classical thermodynamical result of Carnot, η(c)=1-T(C)/T(H), with T(H) (T(C)) being the temperature along the isothermal process at high (low) temperature. We prove that under the same conditions, the efficiency η=1-E(C)/E(H) is bounded from above the Carnot efficiency, η(c)=1-T(C)/T(H), and even quantum dynamics is reversible.

  14. Monitoring vibrations

    Energy Technology Data Exchange (ETDEWEB)

    Tiryaki, B. [Hacettepe University (Turkey). Dept. of Mining Engineering

    2003-12-01

    The paper examines the prediction and optimisation of machine vibrations in longwall shearers. Underground studies were carried out at the Middle Anatolian Lignite Mine, between 1993 and 1997. Several shearer drums with different pick lacing arrangements were designed and tested on double-ended ranging longwall shearers employed at the mine. A computer program called the Vibration Analysis Program (VAP) was developed for analysing machine vibrations in longwall shearers. Shearer drums that were tested underground, as well as some provided by leading manufacturers, were analyzed using these programs. The results of the experiments and computer analyses are given in the article. 4 refs., 9 figs.

  15. Ultrafast electronic relaxation and vibrational dynamics in a polyacetylene derivative

    Science.gov (United States)

    Kobayashi, Takayoshi; Iiyama, Tsugumasa; Okamura, Kotaro; Du, Juan; Masuda, Toshio

    2013-04-01

    Real-time vibrational spectra in a polyacetylene derivative, poly[o-TFMPA([o-(trifluoromethyl) phenyl]acetylene)] in a broad electronic spectral region were observed using a sub-7-fs laser. Using the frequencies and initial phases of vibrational modes obtained by the spectroscopy, the assignment of the wavepackets was made. From the first moment, Huang-Rhys parameters were determined for six most prominent modes, which characterize the potential hypersurface composed of multi-dimensional vibrational mode spaces.

  16. A line-of-sight electron cyclotron emission receiver for electron cyclotron resonance heating feedback control of tearing modes

    DEFF Research Database (Denmark)

    Oosterbeek, J.W.; Bürger, A.; Westerhof, E.

    2008-01-01

    An electron cyclotron emission (ECE) receiver inside the electron cyclotron resonance heating (ECRH) transmission line has been brought into operation. The ECE is extracted by placing a quartz plate acting as a Fabry-Perot interferometer under an angle inside the electron cyclotron wave (ECW) beam...

  17. Vibrational Diver

    Science.gov (United States)

    Kozlov, Victor; Ivanova, Alevtina; Schipitsyn, Vitalii; Stambouli, Moncef

    2014-10-01

    The paper is concerned with dynamics of light solid in cavity with liquid subjected to rotational vibration in the external force field. New vibrational phenomenon - diving of a light cylinder to the cavity bottom is found. The experimental investigation of a horizontal annulus with a partition has shown that under vibration a light body situated in the upper part of the layer is displaced in a threshold manner some distance away from the boundary. In this case the body executes symmetric tangential oscillations. An increase of the vibration intensity leads to a tangential displacement of the body near the external boundary. This displacement is caused by the tangential component of the vibrational lift force, which appears as soon as the oscillations lose symmetry. In this case the trajectory of the body oscillatory motion has the form of a loop. The tangential lift force makes stable the position of the body on the inclined section of the layer and even in its lower part. A theoretical interpretation has been proposed, which explains stabilization of a quasi-equilibrium state of a light body near the cavity bottom in the framework of vibrational hydromechanics.

  18. Concepts for a theoretical and experimental study of lifting rotor random loads and vibrations (further experiments with progressing/regressing rotor flapping modes), Phase 7-C

    Science.gov (United States)

    Hohenemser, K. H.; Crews, S. T.

    1973-01-01

    The experiments with progressing/regressing forced rotor flapping modes have been extended in several directions and the data processing method has been considerably refined. The 16 inch hingeless 2-bladed rotor model was equipped with a new set of high precision blades which removed previously encountered tracking difficulties at high advance ratio, so that tests up to .8 rotor advance ratio could be conducted. In addition to data with 1.20 blade natural flapping frequency data at 1.10 flapping frequency were obtained. Outside the wind tunnel, tests with a ground plate located at different distances below the rotor were conducted while recording the dynamic downflow at a station .2R below the rotor plane with a hot wire anemometer.

  19. Change of Radial Gap Value in Axial Compressors at Modes of Turbine Plant Heating and Shut-Down

    Directory of Open Access Journals (Sweden)

    A. S. Laskine

    2007-01-01

    Full Text Available Designing of highly-efficient axial compressors is connected with their better aerodynamic cleanness. One of the ways is to minimize radial clearances for decreasing leakages and, consequently, increasing efficiency. At the same time it is necessary to exclude stator touching by rotor blades.ANSYS complex has been used to reduce a gap by 1.5–2.0-fold in comparison with the existing one.It has become possible to obtain dependences of radial displacement of peripheral blade edge and stator ring element, located above it, on heating time.Practical and research value of the paper is in the development of a methodology for calculation of heating (cooling, which can be applied while designing axial turbine machines and evaluating the possible minimization of radial gap in the case that excludes touching.

  20. Shaft mode shape demonstration

    Science.gov (United States)

    Grissom, R.

    1985-01-01

    The dynamic response of a rotating machine is directly influenced by its geometric configuration and all aspects of the rotor construction. These determine two significant parameters, mass distribution and stiffness, which yield a spectrum of natural frequencies and mode shapes. The mode shapes can be presented as snapshots of the characteristic amplitude/phase reponse patterns of the shaft, due to the major forcing function of unbalance, at different rotative speeds. To demonstrate the three shaft mode shapes of the rotor rig using the Shaft Mode Demonstrator and oscilloscopes. The synchronous (1X) amplitude and phase of the rotor vibration in the vertical direction from several points along the shaft is displayed on corresponding points of the demonstrator. Unfiltered vibration from vertical and horizontal probe pairs is displayed on the oscilloscopes in orbit format for a dynamic presentation of the mode shape.

  1. Quenching of self-excited vibrations

    NARCIS (Netherlands)

    Verhulst, F.

    2005-01-01

    Stable normal-mode vibrations in engineering can be undesirable and one of the possibilities for quenching these is by embedding the oscillator in an autoparametric system by coupling to a damped oscillator. There exists the possibility of destabilizing the undesirable vibrations by a suitable

  2. Smart Dual-Mode Heat Pump With HP2Grid Functionality To Support Large-Scale Integration Of Intermittent Renewables

    DEFF Research Database (Denmark)

    Carmo, Carolina; Blarke, Morten Boje

    2013-01-01

    The transition towards a 100 % fossil-free energy system, while achieving extreme penetration levels of intermittent wind and solar power in electricity generation, requires demandside technologies that are smart (intermittency-friendly) and efficient. The interaction between electric and thermal...... materials and the ability to generate electricity back to the grid. This new concept will not only improve the residential thermal supply system efficiency by 30-40 %, but will also extend the current intra-day flexibility of heat pumps to a wider range of flexible uses. In this paper, we will investigate...

  3. Vibrations of Damaged Functionally Graded Cantilever Beams

    Science.gov (United States)

    Byrd, Larry W.; Birman, Victor

    2008-02-01

    The paper discusses closed-form solutions of the problems of free and forced vibrations of a functionally graded cantilever FGM beam with and without damage. The mode of damage considered in the paper is represented by cracks that are perpendicular to the axis of the beam. Notably, such mode of damage was observed in experiments on representative FGM beams. Forced vibrations considered in the paper were generated by a kinematic excitation of the clamped end of the beam.

  4. Vibration response of misaligned rotors

    Science.gov (United States)

    Patel, Tejas H.; Darpe, Ashish K.

    2009-08-01

    Misalignment is one of the common faults observed in rotors. Effect of misalignment on vibration response of coupled rotors is investigated in the present study. The coupled rotor system is modelled using Timoshenko beam elements with all six dof. An experimental approach is proposed for the first time for determination of magnitude and harmonic nature of the misalignment excitation. Misalignment effect at coupling location of rotor FE model is simulated using nodal force vector. The force vector is found using misalignment coupling stiffness matrix, derived from experimental data and applied misalignment between the two rotors. Steady-state vibration response is studied for sub-critical speeds. Effect of the types of misalignment (parallel and angular) on the vibration behaviour of the coupled rotor is examined. Along with lateral vibrations, axial and torsional vibrations are also investigated and nature of the vibration response is also examined. It has been found that the misalignment couples vibrations in bending, longitudinal and torsional modes. Some diagnostic features in the fast Fourier transform (FFT) of torsional and longitudinal response related to parallel and angular misalignment have been revealed. Full spectra and orbit plots are effectively used to reveal the unique nature of misalignment fault leading to reliable misalignment diagnostic information, not clearly brought out by earlier studies.

  5. Operating safety of a hot-shot wind tunnel with combined test gas heating in stabilization mode

    Science.gov (United States)

    Shumskii, V. V.; Yaroslavtsev, M. I.

    2017-07-01

    In the present paper, we analyze emergency situations typical of short-duration wind tunnels with electric-arc or combined test-gas heating in the presence of stabilization and diaphragm-rupturing systems, which occur in the case of no discharge initiation in the settling chamber, with the capacitor battery having remained charged during the start of wind-tunnel systems. For avoiding such emergency situations, some additional changes based on using feedback elements are introduced into the wind-tunnel design: the piston of the fast-response valve is made hollow for increasing the volume of the shutoff cavity and for making the release of pressure from this cavity unnecessary; the high-pressure channel, which connects the piston and the piston rod with the settling-chamber cavity, is filled with a liquid and is closed from the side of the settling chamber with a piston; the device for controlled diaphragm breakdown is provided with an external electric circuit intended to control the diaphragm-rupturing process. Those modifications allow subsequent functioning of the wind-tunnel systems only in the presence of heat-supply-induced pressure growth in the settling chamber of the wind tunnel.

  6. Infrared spectra of thin films of α-crystalline hexafluoroethane: a manifestation of resonant dipole-dipole interaction in the range of fundamental vibrational modes ν5 and ν10

    Science.gov (United States)

    Golubkova, O. S.; Kataeva, T. S.; Shchepkin, D. N.; Asfin, R. E.

    2017-06-01

    Infrared reflection-absorption spectra of thin films of α-crystalline hexafluoroethane deposited on a gold-plated copper mirror are measured at temperatures of 70 and 80 K. The bands corresponding to strong in the dipole absorption vibrations ν5 and ν10 have complex contours, the shape of which is explained in terms of the resonant dipole-dipole interaction between identical spectrally active molecules of the crystal. Splittings of the complex ν5 and ν10 bands are explained taking into account two effects: the Davydov splitting and the LO-TO splitting of the strong modes. Bands of the asymmetric 13C12CF6 isotopologue in the absorption spectrum of the crystal exhibit an anomalously large isotope shift as compared with the shift in the spectrum of free molecules. This anomaly is explained by intermolecular resonant dipole-dipole interaction of asymmetric 13C12CF6 isotopologue with molecules of the environment, consisting of the most abundant 12C2F6 isotopologue. The correctness of the given interpretation is confirmed calculating these three effects in the model of resonant dipole-dipole interaction.

  7. Three-dimensional free vibration analysis of thick laminated circular ...

    African Journals Online (AJOL)

    Dr Oke

    mechanical systems is understanding the free vibration behavior of different plate components. The dynamic response of complex engineering systems is intimately linked with plate response frequencies as well as vibration mode shapes. A thorough analysis of free vibration data is often useful in arriving at the resonant ...

  8. Ultrafast vibrations of gold nanorings

    DEFF Research Database (Denmark)

    Kelf, T; Tanaka, Y; Matsuda, O

    2011-01-01

    We investigate the vibrational modes of gold nanorings on a silica substrate with an ultrafast optical technique. By comparison with numerical simulations, we identify several resonances in the gigahertz range associated with axially symmetric deformations of the nanoring and substrate. We...

  9. Phase coherence of parametric-decay modes during high-harmonic fast-wave heating in the National Spherical Torus Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Carlsson, J. A., E-mail: carlsson@pppl.gov [Crow Radio and Plasma Science, Princeton, New Jersey 08540 (United States); Wilson, J. R.; Hosea, J. C.; Greenough, N. L.; Perkins, R. J. [Princeton Plasma Physics Laboratory, P.O. Box 451, Princeton, New Jersey 08543-0451 (United States)

    2016-06-15

    Third-order spectral analysis, in particular, the auto bicoherence, was applied to probe signals from high-harmonic fast-wave heating experiments in the National Spherical Torus Experiment. Strong evidence was found for parametric decay of the 30 MHz radio-frequency (RF) pump wave, with a low-frequency daughter wave at 2.7 MHz, the local majority-ion cyclotron frequency. The primary decay modes have auto bicoherence values around 0.85, very close to the theoretical value of one, which corresponds to total phase coherence with the pump wave. The threshold RF pump power for onset of parametric decay was found to be between 200 kW and 400 kW.

  10. FEM Updating of Tall Buildings using Ambient Vibration Data

    DEFF Research Database (Denmark)

    Ventura, C. E.; Lord, J. F.; Turek, M.

    2005-01-01

    Ambient vibration testing is the most economical non-destructive testing method to acquire vibration data from large civil engineering structures. The purpose of this paper is to demonstrate how ambient vibration Modal Identification techniques can be effectively used with Model Updating tools...... and the corresponding mode shapes. The degree of torsional coupling between the modes was also investigated. The modal identification results obtained from ambient vibration measurements of each building were used to update a finite element model of the structure. The starting model of each structure was developed from...... an ambient vibration modal identification....

  11. Broadband Radiation Modes: Estimation and Active Control

    NARCIS (Netherlands)

    Berkhoff, Arthur P.

    In this paper we give a formulation of the most efficiently radiating vibration patterns of a vibrating body, the radiation modes, in the time domain. The radiation modes can be used to arrive at efficient weighting schemes for an array of sensors in order to reduce the controller dimensionality.

  12. Vibrating minds

    CERN Document Server

    2009-01-01

    Ed Witten is one of the leading scientists in the field of string theory, the theory that describes elementary particles as vibrating strings. This week he leaves CERN after having spent a few months here on sabbatical. His wish is that the LHC will unveil supersymmetry.

  13. Vibrational Cooling in A Cold Ion Trap: Vibrationally Resolved Photoelectron Spectroscopy of Cold C60- Anions

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xue B.; Woo, Hin-koon; Wang, Lai S.

    2005-08-01

    We demonstrate vibrational cooling of anions via collisions with a background gas in an ion trap attached to a cryogenically controlled cold head (10 ? 400 K). Photoelectron spectra of vibrationally cold C60- anions, produced by electrospray ionization and cooled in the cold ion trap, have been obtained. Relative to spectra taken at room temperature, vibrational hot bands are completely eliminated, yielding well resolved vibrational structures and a more accurate electron affinity for neutral C60. The electron affinity of C60 is measured to be 2.683 ? 0.008 eV. The cold spectra reveal complicated vibrational structures for the transition to the C60 ground state due to the Jahn-Teller effect in the ground state of C60-. Vibrational excitations in the two Ag modes and eight Hg modes are observed, providing ideal data to assess the vibronic couplings in C60-.

  14. ICRF mode conversion in three-ion species heating experiment and in flow drive experiment on the Alcator C-Mod tokamak

    Directory of Open Access Journals (Sweden)

    Lin Y.

    2017-01-01

    Full Text Available In recent three-ion species (majority D and H plus a trace level of 3He ICRF heating experiments on Alcator C-Mod, double mode conversion on both sides of the 3He cyclotron resonance has been observed using the phase contrast imaging (PCI system. The MC locations are used to estimate the species concentrations in the plasma. Simulation using TORIC shows that with the 3He level <1%, most RF power is absorbed by the 3He ions and the process can generate energetic 3He ions. In mode conversion (MC flow drive experiment in D(3He plasma at 8 T, MC waves were also monitored by PCI. The MC ion cyclotron wave (ICW amplitude and wavenumber kR have been found to correlate with the flow drive force. The MC efficiency, wave-number k of the MC ICW and their dependence on plasma parameters like Te0 have been studied. Based on the experimental observation and numerical study of the dispersion solutions, a hypothesis of the flow drive mechanism has been proposed.

  15. ICRF mode conversion in three-ion species heating experiment and in flow drive experiment on the Alcator C-Mod tokamak

    Science.gov (United States)

    Lin, Y.; Wukitch, S. J.; Edlund, E.; Ennever, P.; Hubbard, A. E.; Porkolab, M.; Rice, J.; Wright, J.

    2017-10-01

    In recent three-ion species (majority D and H plus a trace level of 3He) ICRF heating experiments on Alcator C-Mod, double mode conversion on both sides of the 3He cyclotron resonance has been observed using the phase contrast imaging (PCI) system. The MC locations are used to estimate the species concentrations in the plasma. Simulation using TORIC shows that with the 3He level <1%, most RF power is absorbed by the 3He ions and the process can generate energetic 3He ions. In mode conversion (MC) flow drive experiment in D(3He) plasma at 8 T, MC waves were also monitored by PCI. The MC ion cyclotron wave (ICW) amplitude and wavenumber kR have been found to correlate with the flow drive force. The MC efficiency, wave-number k of the MC ICW and their dependence on plasma parameters like Te0 have been studied. Based on the experimental observation and numerical study of the dispersion solutions, a hypothesis of the flow drive mechanism has been proposed.

  16. Lattice Vibrations in Chlorobenzenes:

    DEFF Research Database (Denmark)

    Reynolds, P. A.; Kjems, Jørgen; White, J. W.

    1974-01-01

    Lattice vibrational dispersion curves for the ``intermolecular'' modes in the triclinic, one molecule per unit cell β phase of p‐C6D4Cl2 and p‐C6H4Cl2 have been obtained by inelastic neutron scattering. The deuterated sample was investigated at 295 and at 90°K and a linear extrapolation to 0°K...... was applied in order to correct for anharmonic effects. Calculations based on the atom‐atom model for van der Waals' interaction and on general potential parameters for the aromatic compounds agree reasonably well with the experimental observations. There is no substantial improvement in fit obtained either...

  17. Experimental Modal Analysis on Vibrations in the Building Construction

    OpenAIRE

    成瀬, 治興; 佐野, 泰之; 北畠, 弘基

    1996-01-01

    This paper describes some results of vibration propagation characteristics of two rooms next door to each other in the actual building construction (including floor, walls, and upstairfloor) by experimental modal analysis. In addition, we investigate about vibration response of measuring points by forced response and sensitivity analysis. The results are summarized as follows. The vibration of lower modes gives larger effect to vibration propagation characteristics of building construction th...

  18. Another approach to vibrational analysis of stepped structures

    CSIR Research Space (South Africa)

    Fedotov, I

    2006-01-01

    Full Text Available Hz. First resonance is a pendulum mode at which the stepped bar vibrates as “rigid” pendu- lum. All other modes are “longitudinal”. Geometry of the bar was specially chosen so that vibration amplitude of the junction between the cylindrical...

  19. Improved assignments of the vibrational fundamental modes of ortho -, meta -, and para -xylene using gas- and liquid-phase infrared and Raman spectra combined with ab initio calculations: Quantitative gas-phase infrared spectra for detection

    Energy Technology Data Exchange (ETDEWEB)

    Lindenmaier, Rodica; Scharko, Nicole K.; Tonkyn, Russell G.; Nguyen, Kiet T.; Williams, Stephen D.; Johnson, Timothy J.

    2017-07-25

    Xylenes contain a blend of the ortho-, meta-, and para- isomers, and all are abundant contaminants in the ground, surface waters, and air. To better characterize xylene and to better enable its detection, we report high quality quantitative vapor-phase infrared spectra of all three isomers over the 540-6500 cm-1 range. All fundamental vibrational modes are assigned based on these vapor-phase infrared spectra, liquid-phase infrared and Raman spectra, along with density functional theory (DFT), ab initio MP2 and high energy-accuracy compound theoretical model (W1BD) calculations. Both MP2 and DFT predict a single conformer with C2v symmetry for ortho-xylene, and two conformers each for meta- and para-xylene, depending on the preferred orientations of the methyl groups. For meta-xylene the two conformers have Cs and C2 symmetry, and for para-xylene these conformers have C2v or C2h symmetry. Since the relative population of the two conformers is approximately 50% for both isomers and predicted frequencies and intensities are very similar for each conformer, we made an arbitrary choice to discuss the Cs conformer for meta-xylene and the C2v conformer for para-xylene. We report integrated band intensities for all isomers. Using the quantitative infrared data, we determine the global warming potential values of each isomer and discuss potential bands for atmospheric monitoring.

  20. Chatter vibrations of high-performance motorcycles

    Science.gov (United States)

    Sharp, R. S.; Watanabe, Y.

    2013-03-01

    Motorcycle racing teams occasionally experience speed-limiting vibrations of around 25 Hz frequency in mid-corner. The nature of the vibrations has not been closely defined yet and the mechanics are currently not properly understood. Conventional motorcycle-dynamics models are shown here to reveal the existence of a vibration mode that aligns with the experience being referred to, suggesting some explanations. Root loci for variations in speed or cornering vigour, demonstrating modal characteristics for small perturbations from trim states, are employed to indicate how the mode responds to changes in operation and design. Modal participation is examined for a lightly damped case. Influences on the natural frequency and damping of the mode are found and a way of stabilising the mode is suggested.

  1. Active damping of the 1D rocking mode

    NARCIS (Netherlands)

    Babakhani, B.; de Vries, Theodorus J.A.

    Active damping of a rotational vibration mode in the linear guidance of a precision machine in a one dimensional (1D) setting is considered in this paper. This so-called rocking mode presents itself in machines having linear actuation. The limitation this vibration mode imposes on the machine

  2. Dual source heat pump

    Science.gov (United States)

    Ecker, Amir L.; Pietsch, Joseph A.

    1982-01-01

    What is disclosed is a heat pump apparatus for conditioning a fluid characterized by a fluid handler and path for circulating the fluid in heat exchange relationship with a refrigerant fluid; at least two refrigerant heat exchangers, one for effecting heat exchange with the fluid and a second for effecting heat exchange between refrigerant and a heat exchange fluid and the ambient air; a compressor for efficiently compressing the refrigerant; at least one throttling valve for throttling liquid refrigerant; a refrigerant circuit; refrigerant; a source of heat exchange fluid; heat exchange fluid circulating device and heat exchange fluid circuit for circulating the heat exchange fluid in heat exchange relationship with the refrigerant; and valves or switches for selecting the heat exchangers and direction of flow of the refrigerant therethrough for selecting a particular mode of operation. The heat exchange fluid provides energy for defrosting the second heat exchanger when operating in the air source mode and also provides a alternate source of heat.

  3. Kinetic theory for DNA melting with vibrational entropy

    Science.gov (United States)

    Sensale, Sebastian; Peng, Zhangli; Chang, Hsueh-Chia

    2017-10-01

    By treating DNA as a vibrating nonlinear lattice, an activated kinetic theory for DNA melting is developed to capture the breakage of the hydrogen bonds and subsequent softening of torsional and bending vibration modes. With a coarse-grained lattice model, we identify a key bending mode with GHz frequency that replaces the hydrogen vibration modes as the dominant out-of-phase phonon vibration at the transition state. By associating its bending modulus to a universal in-phase bending vibration modulus at equilibrium, we can hence estimate the entropic change in the out-of-phase vibration from near-equilibrium all-atom simulations. This and estimates of torsional and bending entropy changes lead to the first predictive and sequence-dependent theory with good quantitative agreement with experimental data for the activation energy of melting of short DNA molecules without intermediate hairpin structures.

  4. Effect of tube-support interaction on the dynamic responses of heat exchanger tubes. [LMFBR

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Y.S.; Jendrzejczyk, J.A.; Wambsganss, M.W.

    1977-01-01

    Operating heat exchangers have experienced tube damages due to excessive flow-induced vibration. The relatively small inherent tube-to-baffle hole clearances associated with manufacturing tolerances in heat exchangers affect the tube vibrational characteristics. In attempting a theoretical analysis, questions arise as to the effects of tube-baffle impacting on dynamic responses. Experiments were performed to determine the effects of tube-baffle impacting in vertical/horizontal tube orientation, and in air/water medium on the vibrational characteristics (resonant frequencies, mode shapes, and damping) and displacement response amplitudes of a seven-span tube model. The tube and support conditions were prototypic, and overall length approximately one-third that of a straight tube segment of the steam generator designed for the CRBR. The test results were compared with the analytical results based on the multispan beam with ''knife-edge'' supports.

  5. Urban vibrations

    DEFF Research Database (Denmark)

    Morrison, Ann; Knudsen, L.; Andersen, Hans Jørgen

    2012-01-01

      lab   studies   in   that   we   found   a   decreased   detection   rate   in   busy   environments.   Here   we   test   with   a   much   larger   sample   and   age   range,   and   contribute   with   the   first   vibration  sensitivity  testing  outside  the  lab  in  an  urban   public...

  6. Pedagogical Comparison of Five Reactions Performed under Microwave Heating in Multi-Mode versus Mono-Mode Ovens: Diels-Alder Cycloaddition, Wittig Salt Formation, E2 Dehydrohalogenation to Form an Alkyne, Williamson Ether Synthesis, and Fischer Esterification

    Science.gov (United States)

    Baar, Marsha R.; Gammerdinger, William; Leap, Jennifer; Morales, Erin; Shikora, Jonathan; Weber, Michael H.

    2014-01-01

    Five reactions were rate-accelerated relative to the standard reflux workup in both multi-mode and mono-mode microwave ovens, and the results were compared to determine whether the sequential processing of a mono-mode unit could provide for better lab logistics and pedagogy. Conditions were optimized so that yields matched in both types of…

  7. Damping and energy dissipation in soft tissue vibrations during running.

    Science.gov (United States)

    Khassetarash, Arash; Hassannejad, Reza; Enders, Hendrik; Ettefagh, Mir Mohammad

    2015-01-21

    It has been well accepted that the vibrations of soft tissue cannot be simulated by a single sinusoidal function. In fact, these vibrations are a combination of several vibration modes. In this study, these modes are extracted applying a recently developed method namely, partly ensemble empirical mode decomposition (PEEMD). Then, a methodology for estimating the damping properties and energy dissipation caused by damping for each mode is used. Applying this methodology on simulated signals demonstrates high accuracy. This methodology is applied to the acceleration signals of the gastrocnemius muscle during sprinting and the differences between the damping properties of different vibration modes were identified. The results were 1) the damping property of high-frequency mode was higher than that for low-frequency modes. 2) All identified modes were in under damped condition, therefore, the vibrations had an oscillatory nature. 3) The damping ratios of lower modes are about 100% increased compared to higher modes. 4) The energy dissipation occurred in lower modes were much more than that for higher mode; According to the power spectrum of the ground reaction force (GRF), which is the input force into the body, the recent finding supports the muscle tuning paradigm. It is suggested that the damping properties and energy dissipation can be used to distinguish between different running conditions (surface, fatigue, etc.). Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. Measurement-induced operation of two-ion quantum heat machines

    Science.gov (United States)

    Chand, Suman; Biswas, Asoka

    2017-03-01

    We show how one can implement a quantum heat machine by using two interacting trapped ions, in presence of a thermal bath. The electronic states of the ions act like a working substance, while the vibrational mode is modelled as the cold bath. The heat exchange with the cold bath is mimicked by the projective measurement of the electronic states. We show how such measurement in a suitable basis can lead to either a quantum heat engine or a refrigerator, which undergoes a quantum Otto cycle. The local magnetic field is adiabatically changed during the heat cycle. The performance of the heat machine depends upon the interaction strength between the ions, the magnetic fields, and the measurement cost. In our model, the coupling to the hot and the cold baths is never switched off in an alternative fashion during the heat cycle, unlike other existing proposals of quantum heat engines. This makes our proposal experimentally realizable using current tapped-ion technology.

  9. Vibrational coupling in plasmonic molecules.

    Science.gov (United States)

    Yi, Chongyue; Dongare, Pratiksha D; Su, Man-Nung; Wang, Wenxiao; Chakraborty, Debadi; Wen, Fangfang; Chang, Wei-Shun; Sader, John E; Nordlander, Peter; Halas, Naomi J; Link, Stephan

    2017-10-31

    Plasmon hybridization theory, inspired by molecular orbital theory, has been extremely successful in describing the near-field coupling in clusters of plasmonic nanoparticles, also known as plasmonic molecules. However, the vibrational modes of plasmonic molecules have been virtually unexplored. By designing precisely configured plasmonic molecules of varying complexity and probing them at the individual plasmonic molecule level, intramolecular coupling of acoustic modes, mediated by the underlying substrate, is observed. The strength of this coupling can be manipulated through the configuration of the plasmonic molecules. Surprisingly, classical continuum elastic theory fails to account for the experimental trends, which are well described by a simple coupled oscillator picture that assumes the vibrational coupling is mediated by coherent phonons with low energies. These findings provide a route to the systematic optical control of the gigahertz response of metallic nanostructures, opening the door to new optomechanical device strategies. Published under the PNAS license.

  10. A Lanczos algorithm for vibration, suckling and termal analysis

    Science.gov (United States)

    Bostic, Susan W.

    1993-01-01

    This paper reviews an eigensolver algorithm based on the Lanczos Method for vibration, buckling and thermal analysis. The original code was written for inclusion in the Computational Mechanics Testbed (COMET), a general purpose finite element code. A portable version of the Lanczos code that is optimized for high-performance supercomputers has been developed. Special features of the algorithm include the capability to compute rigid body modes, thermal modes and Lanczos vectors that are derived from the applied load vector. The latter is necessary when using the Lanczos vectors as reduced-basis vectors in transient structural response and transient heat conduction calculations. The modularity of the code allows the user the option of including the most up-to-date utilities, such as the equation solver best suited for the application. The algorithm is discussed in detail and results of several applications are presented. Timing results for a vibration application indicate that the Lanczos algorithm is twenty times faster than the subspace iteration method which has been extensively used in the past.

  11. Dynamical transition in proteins and non-Gaussian behavior of low-frequency modes in self-consistent normal mode analysis.

    Science.gov (United States)

    Guo, Jianguang; Budarz, Timo; Ward, Joshua M; Prohofsky, Earl W

    2010-10-01

    Self-consistent normal mode analysis (SCNMA) is applied to heme c type cytochrome f to study temperature-dependent protein motion. Classical normal mode analysis assumes harmonic behavior and the protein mean-square displacement has a linear dependence on temperature. This is only consistent with low-temperature experimental results. To connect the protein vibrational motions between low and physiological temperatures, we have incorporated a fitted set of anharmonic potentials into SCNMA. In addition, quantum harmonic-oscillator theory has been used to calculate the displacement distribution for individual vibrational modes. We find that the modes involving soft bonds exhibit significant non-Gaussian dynamics at physiological temperature, which suggests that it may be the cause of the non-Gaussian behavior of the protein motions probed by elastic incoherent neutron scattering. The combined theory displays a dynamical transition caused by the softening of few "torsional" modes in the low-frequency regime ( 0.6 ps). These modes change from Gaussian to a classical distribution upon heating. Our theory provides an alternative way to understand the microscopic origin of the protein dynamical transition.

  12. Theory of vibration protection

    CERN Document Server

    Karnovsky, Igor A

    2016-01-01

    This text is an advancement of the theory of vibration protection of mechanical systems with lumped and distributed parameters. The book offers various concepts and methods of solving vibration protection problems, discusses the advantages and disadvantages of different methods, and the fields of their effective applications. Fundamental approaches of vibration protection, which are considered in this book, are the passive, parametric and optimal active vibration protection. The passive vibration protection is based on vibration isolation, vibration damping and dynamic absorbers. Parametric vibration protection theory is based on the Shchipanov-Luzin invariance principle. Optimal active vibration protection theory is based on the Pontryagin principle and the Krein moment method. The book also contains special topics such as suppression of vibrations at the source of their occurrence and the harmful influence of vibrations on humans. Numerous examples, which illustrate the theoretical ideas of each chapter, ar...

  13. Vibration Analysis of a Split Path Gearbox

    Science.gov (United States)

    Krantz, Timothy L.; Rashidi, Majid

    1995-01-01

    Split path gearboxes can be attractive alternatives to the common planetary designs for rotorcraft, but because they have seen little use, they are relatively high risk designs. To help reduce the risk of fielding a rotorcraft with a split path gearbox, the vibration and dynamic characteristics of such a gearbox were studied. A mathematical model was developed by using the Lagrangian method, and it was applied to study the effect of three design variables on the natural frequencies and vibration energy of the gearbox. The first design variable, shaft angle, had little influence on the natural frequencies. The second variable, mesh phasing, had a strong effect on the levels of vibration energy, with phase angles of 0 deg and 180 deg producing low vibration levels. The third design variable, the stiffness of the shafts connecting the spur gears to the helical pinions, strongly influenced the natural frequencies of some of the vibration modes, including two of the dominant modes. We found that, to achieve the lowest level of vibration energy, the natural frequencies of these two dominant modes should be less than those of the main excitation sources.

  14. Pin-pin resonance as a reference in determining ballasted railway track vibration behaviour

    NARCIS (Netherlands)

    De Man, A.P.

    2000-01-01

    Pin-pin resonance is one of the most significant preferred vibration modes of beams, which are supported at equal distances, such as rails at sleepers in railway track structures do. Pin-pin resonance is a vibration that appears in one basic (first) mode and several higher modes, however the basic

  15. Wind Turbine Rotors with Active Vibration Control

    DEFF Research Database (Denmark)

    Svendsen, Martin Nymann

    This thesis presents a framework for structural modeling, analysis and active vibration damping of rotating wind turbine blades and rotors. A structural rotor model is developed in terms of finite beam elements in a rotating frame of reference. The element comprises a representation of general...... formulation. The element provides an accurate representation of the eigenfrequencies and whirling modes of the gyroscopic system, and identifies lightly damped edge-wise modes. By adoption of a method for active, collocated resonant vibration of multi-degree-of-freedom systems it is demonstrated...... that these are geometrically well separated. For active vibration control in three-bladed wind turbine rotors the present work presents a resonance-based method for groups of one collective and two whirling modes. The controller is based on the existing resonant format and introduces a dual system targeting the collective...

  16. Multiple source heat pump

    Science.gov (United States)

    Ecker, Amir L.

    1983-01-01

    A heat pump apparatus for conditioning a fluid characterized by a fluid handler and path for circulating a fluid in heat exchange relationship with a refrigerant fluid, at least three refrigerant heat exchangers, one for effecting heat exchange with the fluid, a second for effecting heat exchange with a heat exchange fluid, and a third for effecting heat exchange with ambient air; a compressor for compressing the refrigerant; at least one throttling valve connected at the inlet side of a heat exchanger in which liquid refrigerant is vaporized; a refrigerant circuit; refrigerant; a source of heat exchange fluid; heat exchange fluid circuit and pump for circulating the heat exchange fluid in heat exchange relationship with the refrigerant; and valves or switches for selecting the heat exchangers and directional flow of refrigerant therethrough for selecting a particular mode of operation. Also disclosed are a variety of embodiments, modes of operation, and schematics therefor.

  17. Acoustical analysis of gear housing vibration

    Science.gov (United States)

    Seybert, A. F.; Wu, T. W.; Wu, X. F.; Oswald, Fred B.

    1991-01-01

    The modal and acoustical analysis of the NASA gear-noise rig is described. Experimental modal analysis techniques were used to determine the modes of vibration of the transmission housing. The resulting modal data were then used in a boundary element method (BEM) analysis to calculate the sound pressure and sound intensity on the surface of the housing as well as the radiation efficiency of each mode. The radiation efficiencies of the transmission housing modes are compared with theoretical results for finite, baffled plates. A method that uses the measured mode shapes and the BEM to predict the effect of simple structural changes on the sound radiation efficiency of the modes of vibration is also described.

  18. Improving Robustness of Tuned Vibration Absorbers Using Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    Mohammad H. Elahinia

    2005-01-01

    Full Text Available A conventional passive tuned vibration absorber (TVA is effective when it is precisely tuned to the frequency of a vibration mode; otherwise, it may amplify the vibrations of the primary system. In many applications, the frequency often changes over time. For example, adding or subtracting external mass on the existing primary system results in changes in the system’s natural frequency. The frequency changes of the primary system can significantly degrade the performance of TVA. To cope with this problem, many alternative TVAs (such as semiactive, adaptive, and active TVAs have been studied. As another alternative, this paper investigates the use of Shape Memory Alloys (SMAs in passive TVAs in order to improve the robustness of the TVAs subject to mass change in the primary system. The proposed SMA-TVA employs SMA wires, which exhibit variable stiffness, as the spring element of the TVA. This allows us to tune effective stiffness of the TVA to adapt to the changes in the primary system's natural frequency. The simulation model, presented in this paper, contains the dynamics of the TVA along with the SMA wire model that includes phase transformation, heat transfer, and the constitutive relations. Additionally, a PID controller is included for regulating the applied voltage to the SMA wires in order to maintain the desired stiffness. The robustness analysis is then performed on both the SMA-TVA and the equivalent passive TVA. For our robustness analysis, the mass of the primary system is varied by ± 30% of its nominal mass. The simulation results show that the SMA-TVA is more robust than the equivalent passive TVA in reducing peak vibrations in the primary system subject to change of its mass.

  19. Localized Surface Plasmons in Vibrating Graphene Nanodisks

    DEFF Research Database (Denmark)

    Wang, Weihua; Li, Bo-Hong; Stassen, Erik

    2016-01-01

    in graphene disks have the additional benefit to be highly tunable via electrical stimulation. Mechanical vibrations create structural deformations in ways where the excitation of localized surface plasmons can be strongly modulated. We show that the spectral shift in such a scenario is determined...... by a complex interplay between the symmetry and shape of the modal vibrations and the plasmonic mode pattern. Tuning confined modes of light in graphene via acoustic excitations, paves new avenues in shaping the sensitivity of plasmonic detectors, and in the enhancement of the interaction with optical emitters...

  20. Engine gearbox fault diagnosis using empirical mode ...

    Indian Academy of Sciences (India)

    This paper presents engine gearbox fault diagnosis based on empirical mode decomposition (EMD) and Naı¨ve Bayes algorithm. In this study, vibration signals from a gear box are acquired with healthy and different simulated faulty conditions of gear and bearing. The vibration signals are decomposed into a finite number ...

  1. Determination of electromagnetic modes in oversized corrugated waveguides on the electron cyclotron resonance heating installation at the tokamak Tore Supra; Determination de modes electromagnetiques de guides d'ondes corrugues surdimensionnes sur l'installation de chauffage des electrons de tokamak Tore Supra

    Energy Technology Data Exchange (ETDEWEB)

    Courtois, L

    2001-03-09

    Electron cyclotron resonance heating (ECRH) in the Tore Supra tokamak constitutes an important step in the research aimed at obtaining thermonuclear fusion reactions. Electron heating is achieved by transmitting an electromagnetic wave from the oscillators (gyrotrons) to the plasma via the fundamental mode, propagating in oversized corrugated waveguides. Maximizing the proportion of the gyrotron power coupled to the fundamental waveguide mode is essential for the good functioning of the transmission line and for maximizing the effect on the plasma. This thesis gives all necessary tools for finding the proportion of the fundamental mode and all other modes present in passive components and at the output of the gyrotron as installed in the Tore Supra ECRH plant. This characterisation is based on obtaining amplitude and phase diagrams of the electric field on a plane transverse to the propagation axis. The most difficult part of obtaining these diagrams is measuring the phase which, despite the very short wavelength, is measured directly at low power levels. At high power levels the phase is numerically reconstructed from amplitude measurements for gyrotron characterisation. A complete theoretical study of the phase reconstruction code is given including its validation with theoretical diagrams. This study allows the realisation of a modal characterisation unit electromagnetic for measurement of radiated beams and usable in each part of the ECRH installation. At the end, the complete modal characterisation is given at low level for a mode converter and also at high level for the first series gyrotron installed at TORE SUPRA. (author)

  2. Optimization design of high power ultrasonic circular ring radiator in coupled vibration.

    Science.gov (United States)

    Xu, Long; Lin, Shuyu; Hu, Wenxu

    2011-10-01

    This paper presents a new high power ultrasonic (HPU) radiator, which consists of a transducer, an ultrasonic horn, and a metal circular ring. Both the transducer and horn in longitudinal vibrations are used to drive a metal circular ring in a radial-axial coupled vibration. This coupled vibration cannot only generate ultrasound in both the radial and axial directions, but also focus the ultrasound inside the circular ring. Except for the radial-axial coupled vibration mode, the third longitudinal harmonic vibration mode with relative large vibration amplitude is also detected, which can be used as another operation mode. Overall, the HPU with these two vibration modes should have good potential to be applied in liquid processing, such as sonochemistry, ultrasonic cleaning, and Chinese herbal medicine extraction. Copyright © 2011 Elsevier B.V. All rights reserved.

  3. Study of core support barrel vibration monitoring using ex-core neutron noise analysis and fuzzy logic algorithm

    Directory of Open Access Journals (Sweden)

    Robby Christian

    2015-03-01

    A distinct pattern of phase differences was observed for each of the vibration models. The developed fuzzy logic module demonstrated successful recognition of the vibration frequencies, modes, orders, directions, and phase differences within 0.4 ms for the beam and shell mode vibrations.

  4. Vibrational energy transport in acetylbenzonitrile described by an ab initio-based quantum tier model

    Science.gov (United States)

    Fujisaki, Hiroshi; Yagi, Kiyoshi; Kikuchi, Hiroto; Takami, Toshiya; Stock, Gerhard

    2017-01-01

    Performing comprehensive quantum-chemical calculations, a vibrational Hamiltonian of acetylbenzonitrile is constructed, on the basis of which a quantum-mechanical "tier model" is developed that describes the vibrational dynamics following excitation of the CN stretch mode. Taking into account 36 vibrational modes and cubic and quartic anharmonic couplings between up to three different modes, the tier model calculations are shown to qualitatively reproduce the main findings of the experiments of Rubtsov and coworkers (2011), including the energy relaxation of the initially excited CN mode and the structure-dependent vibrational transport. Moreover, the calculations suggest that the experimentally measured cross-peak among the CN and CO modes does not correspond to direct excitation of the CO normal mode but rather reflects excited low-frequency vibrations that anharmonically couple to the CO mode. Complementary quasiclassical trajectory calculations are found to be in good overall agreement with the quantum calculations.

  5. Single mode variable-sensitivity fiber optic sensors

    Science.gov (United States)

    Murphy, K. A.; Fogg, B. R.; Gunther, M. F.; Claus, R. O.

    1992-01-01

    We review spatially-weighted optical fiber sensors that filter specific vibration modes from one dimensional beams placed in clamped-free and clamped-clamped configurations. The sensitivity of the sensor is varied along the length of the fiber by tapering circular-core, dual-mode optical fibers. Selective vibration mode suppression on the order of 10 dB was obtained. We describe experimental results and propose future extensions to single mode sensor applications.

  6. Hand-Arm vibration assessment among tiller operator

    Directory of Open Access Journals (Sweden)

    P. Nassiri

    2013-08-01

    Result: Results of the present study indicated that in all measured situations, exposure to hand arm vibration was higher than the standard limit suggested by Iranian occupational health committee and there was risk of vibration-induced disorders. The maximum exposure to vibration is in plowing ground. Exposure to hand arm vibration in three modes of plowing, transmission and natural, were respectively 16.95, 14.16 and 8.65 meters per second squared. Additionally, in all situations, vibration exposure was highest in the X-axis in comparison with Z- and Y-axes. .Conclusion: This study emphasizes on the need to provide intervention and controlling and managing strategies in order to eliminate or reduce vibration transmitted from tiller to operators hand and arm and also prevent to serious problems including neurovascular disorders, discomfort and white finger syndrome. Meanwhile, more studies are necessary to identify the sources of vibration on different models of tiller.

  7. Vibrational spectra of nickel metalloporphyrins: An algebraic approach

    Indian Academy of Sciences (India)

    ... molecules. In view of the considerable amount of experimental activity in this area, one needs theoretical models within which to interpret experimental data. Using Lie algebraic method, the vibrational energy levels of nickel metalloporphyrins like Ni(OEP), Ni porphyrin and Ni(TPP) are calculated for 16 vibrational modes.

  8. Resonant vibration control of three-bladed wind turbine rotors

    DEFF Research Database (Denmark)

    Krenk, Steen; Svendsen, Martin Nymann; Høgsberg, Jan Becker

    2012-01-01

    Rotors with blades, as in wind turbines, are prone to vibrations due to the flexibility of the blades and the support. In the present paper a theory is developed for active control of a combined set of vibration modes in three-bladed rotors. The control system consists of identical collocated...

  9. Modelling, structural, thermal, optical and vibrational studies of a ...

    Indian Academy of Sciences (India)

    sis of all the fundamental vibration modes using the VEDA. 4 program [21]. Scaling factors used in this study were taken from literature [22]. In order to take into account the effect of intermolecular interactions on geometrical parameters and vibrational spectroscopy, we have considered an appropriate cluster model built up ...

  10. Molecular structure and vibrational analysis of Trifluoperazine by FT-IR, FT-Raman and UV-Vis spectroscopies combined with DFT calculations.

    Science.gov (United States)

    Rajesh, P; Gunasekaran, S; Gnanasambandan, T; Seshadri, S

    2015-02-25

    The complete vibrational assignment and analysis of the fundamental vibrational modes of Trifluoperazine (TFZ) was carried out using the experimental FT-IR, FT-Raman and UV-Vis data and quantum chemical studies. The observed vibrational data were compared with the wavenumbers derived theoretically for the optimized geometry of the compound from the DFT-B3LYP gradient calculations employing 6-31G (d,p) basis set. Thermodynamic properties like entropy, heat capacity and enthalpy have been calculated for the molecule. The HOMO-LUMO energy gap has been calculated. The intramolecular contacts have been interpreted using natural bond orbital (NBO) and natural localized molecular orbital (NLMO) analysis. Important non-linear properties such as first hyperpolarizability of TFZ have been computed using B3LYP quantum chemical calculation. Copyright © 2014 Elsevier B.V. All rights reserved.

  11. Dual-Mode Combustor

    Science.gov (United States)

    Trefny, Charles J (Inventor); Dippold, Vance F (Inventor)

    2013-01-01

    A new dual-mode ramjet combustor used for operation over a wide flight Mach number range is described. Subsonic combustion mode is usable to lower flight Mach numbers than current dual-mode scramjets. High speed mode is characterized by supersonic combustion in a free-jet that traverses the subsonic combustion chamber to a variable nozzle throat. Although a variable combustor exit aperture is required, the need for fuel staging to accommodate the combustion process is eliminated. Local heating from shock-boundary-layer interactions on combustor walls is also eliminated.

  12. Anti noise system and method using broadband radiation modes

    NARCIS (Netherlands)

    Berkhoff, Arthur P.

    2002-01-01

    Anti noise system and method, in particular for suppressing sound radiated from a structure, using a formulation of the most efficiently radiating vibration patterns of a vibrating body, the radiation modes, in the time domain. The radiation modes can be used to arrive at efficient weighting schemes

  13. Nonlinear thermoelectric properties of molecular junctions with vibrational coupling

    DEFF Research Database (Denmark)

    Leijnse, Martin Christian; Wegewijs, M. R.; Flensberg, Karsten

    2010-01-01

    We present a detailed study of the nonlinear thermoelectric properties of a molecular junction, represented by a dissipative Anderson-Holstein model. A single-orbital level with strong Coulomb interaction is coupled to a localized vibrational mode and we account for both electron and phonon...... conditions, which are found to be qualitatively changed by the presence of the vibrational mode. Based on this study of a generic model system, we discuss the desirable properties of molecular junctions for thermoelectric applications....

  14. Subsurface melting of nylon by friction-induced vibrations

    NARCIS (Netherlands)

    Vroegop, P.H.; Bosma, R.

    1985-01-01

    Dry sliding of nylon on steel may lead to subsurface recrystallization of the polymer. This phenomenon is described and explained by subsurface melting due to internal heating as a result of the dissipation of frictioninduced vibrations at frequencies above 10 kHz. A vibration model relating the

  15. Vibrational and electronic spectroscopic studies of melatonin

    Science.gov (United States)

    Singh, Gurpreet; Abbas, J. M.; Dogra, Sukh Dev; Sachdeva, Ritika; Rai, Bimal; Tripathi, S. K.; Prakash, Satya; Sathe, Vasant; Saini, G. S. S.

    2014-01-01

    We report the infrared absorption and Raman spectra of melatonin recorded with 488 and 632.8 nm excitations in 3600-2700 and 1700-70 cm-1 regions. Further, we optimized molecular structure of the three conformers of melatonin within density functional theory calculations. Vibrational frequencies of all three conformers have also been calculated. Observed vibrational bands have been assigned to different vibrational motions of the molecules on the basis of potential energy distribution calculations and calculated vibrational frequencies. Observed band positions match well with the calculated values after scaling except Nsbnd H stretching mode frequencies. It is found that the observed and calculated frequencies mismatch of Nsbnd H stretching is due to intermolecular interactions between melatonin molecules.

  16. Long-range vibration sensor based on correlation analysis of optical frequency-domain reflectometry signals.

    Science.gov (United States)

    Ding, Zhenyang; Yao, X Steve; Liu, Tiegen; Du, Yang; Liu, Kun; Han, Qun; Meng, Zhuo; Chen, Hongxin

    2012-12-17

    We present a novel method to achieve a space-resolved long- range vibration detection system based on the correlation analysis of the optical frequency-domain reflectometry (OFDR) signals. By performing two separate measurements of the vibrated and non-vibrated states on a test fiber, the vibration frequency and position of a vibration event can be obtained by analyzing the cross-correlation between beat signals of the vibrated and non-vibrated states in a spatial domain, where the beat signals are generated from interferences between local Rayleigh backscattering signals of the test fiber and local light oscillator. Using the proposed technique, we constructed a standard single-mode fiber based vibration sensor that can have a dynamic range of 12 km and a measurable vibration frequency up to 2 kHz with a spatial resolution of 5 m. Moreover, preliminarily investigation results of two vibration events located at different positions along the test fiber are also reported.

  17. Vibration of imperfect rotating disk

    Directory of Open Access Journals (Sweden)

    Půst L.

    2011-12-01

    Full Text Available This study is concerned with the theoretical and numerical calculations of the flexural vibrations of a bladed disk. The main focus of this study is to elaborate the basic background for diagnostic and identification methods for ascertaining the main properties of the real structure or an experimental model of turbine disks. The reduction of undesirable vibrations of blades is proposed by using damping heads, which on the experimental model of turbine disk are applied only on a limited number of blades. This partial setting of damping heads introduces imperfection in mass, stiffness and damping distribution on the periphery and leads to more complicated dynamic properties than those of a perfect disk. Calculation of FEM model and analytic—numerical solution of disk behaviour in the limited (two modes frequency range shows the splitting of resonance with an increasing speed of disk rotation. The spectrum of resonance is twice denser than that of a perfect disk.

  18. Free-Vibration Analysis of Structures

    Science.gov (United States)

    Gupta, K. K.

    1984-01-01

    Unified numerical procedure for free-vibration analysis of structures developed and incorporated into EIGSOL computer program. Dynamic response analysis of primary importance in design of wide range of practical structures such as space-craft, buildings, and rotating machineries. Procedure determines natural frequencies and associated modes in structural design.

  19. Vibration reduces thermal pain in adjacent dermatomes.

    Science.gov (United States)

    Yarnitsky, D; Kunin, M; Brik, R; Sprecher, E

    1997-01-01

    Spatial summation of thermal pain crosses dermatomal boundaries. In this study we examined whether a vibrational stimulus applied to adjacent or remote dermatomes affects thermal pain perception to the volar forearm. Contact heat at 2 degrees C above thermal pain threshold was applied, and a Visual Analog Scale (VAS) was used for pain assessment. We found a significant decrease in mean VAS rating when simultaneous vibratory stimuli were given to the dermatome adjacent to that receiving thermal stimulation, or to the same dermatome on the contralateral side. There was no change in VAS rating when vibration was given two or more dermatomes away. Vibration within the same dermatome also did not yield a significant change in VAS rating, possibly due to difficulty in magnitude assessment of stimuli given simultaneously within a single dermatome. The finding that vibration can reduce pain across dermatomes may allow for more flexible design of stimulation therapy for pain.

  20. Anti-vibration characteristics of rubberised reinforced concrete beams

    OpenAIRE

    Rahman, M; Al-Ghalib, A; Mohammad, FA

    2014-01-01

    The flexural and vibration properties were examined in order to evaluate the anti-vibration characteristics of rubber modified reinforced concrete beam. The rubberised mixtures were produced by replacing 5, 7.5, and 10 % by mass of the fine aggregate with 1–4 mm scrap truck tyre crumb rubber particles. A series of reinforced concrete beam (1,200 × 135 × 90 mm3) was tested in a free vibration mode and then subsequently in a four point flexural tests. The input and output signals from vibration...

  1. The effects of mixing air distribution and heat load arrangement on the performance of ceiling radiant panels under cooling mode of operation

    DEFF Research Database (Denmark)

    Mustakallio, Panu; Kosonen, Risto; Melikov, Arsen Krikor

    2016-01-01

    arrangement and air distribution generated in a room by linear slot diffuser, radial multi-nozzle diffuser and radial swirl induction unit on the cooling power of radiant panels was compared. The impact on the thermal environment was also studied. Measurements were carried out without and with supply air...... 5% to 17% depending on the air distribution method and the heat load arrangement. The most significant effect of the heat load arrangement occured when heat loads are located unevenly and their convection flow turns or weakens the supply air jet flushing the radiant panels....

  2. Nonlinear thermal convection in a layer of nanofluid under G-jitter and internal heating effects

    Directory of Open Access Journals (Sweden)

    Bhadauria B. S.

    2014-01-01

    Full Text Available This paper deals with a mathematical model of controlling heat transfer in nanofluids. The time-periodic vertical vibrations of the system are considered to effect an external control of heat transport along with internal heating effects. A weakly non-linear stability analysis is based on the five-mode Lorenz model using which the Nusselt number is obtained as a function of the thermal Rayleigh number, nano-particle concentration based Rayleigh number, Prandtl number, Lewis number, modified diffusivity ratio, amplitude and frequency of modulation. It is shown that modulation can be effectively used to control convection and thereby heat transport. Further, it is found that the effect of internal Rayleigh number is to enhance the heat and nano-particles transport.

  3. Analysis of Main Types of Vibrations at a Bridge for Passer-Byes

    Directory of Open Access Journals (Sweden)

    Attila Nagy

    2010-10-01

    Full Text Available The present paper deals with the dynamic mode analysis in different situations at a bridge projected for passer-byes, with the help of the AxisVM software. From the multiple studied modes of vibrations we are going to present the main vibrations which appear due to the self-weight of the bridge, due to complex forces (different loads, and also due to seismic forces (mode 1 and mode 9.

  4. Tunable Passive Vibration Suppressor

    Science.gov (United States)

    Boechler, Nicholas (Inventor); Dillon, Robert Peter (Inventor); Daraio, Chiara (Inventor); Davis, Gregory L. (Inventor); Shapiro, Andrew A. (Inventor); Borgonia, John Paul C. (Inventor); Kahn, Daniel Louis (Inventor)

    2016-01-01

    An apparatus and method for vibration suppression using a granular particle chain. The granular particle chain is statically compressed and the end particles of the chain are attached to a payload and vibration source. The properties of the granular particles along with the amount of static compression are chosen to provide desired filtering of vibrations.

  5. Vibrations and Eigenvalues

    Indian Academy of Sciences (India)

    We make music by causing strings, membranes, or air columns to vibrate. Engineers design safe structures by control- ling vibrations. I will describe to you a very simple vibrating system and the mathematics needed to analyse it. The ideas were born in the work of Joseph-Louis Lagrange (1736–1813), and I begin by quot-.

  6. Section 1. Method of determining mode shapes and natural frequencies of the NASA unmodified test structure. Section 2. Continuous beam closed from solution to the NASA-LSS astromast torsional vibration, appendix E

    Science.gov (United States)

    1984-01-01

    The methods used to determine the lower natural frequencies and their corresponding mode shapes of the NASA-LSS Astromast (Unmodified Test Structure), and the mass integrals associated with the mode shapes are illustrated. The test structure is modeled as a cantilever beam with 91 lumped masses and without the tip mass on the free end of the bram. This uncouples the torsion and bending modes and allows for them to be determined separately. The frequency range was limited to an upper bound of 100 rad/sec (15.92 Hz.). In this range from 0.-100. rad/sec, three bending frequencies and one torsion frequency was found.

  7. Fundamental Study of a Combined Hyperthermia System with RF Capacitive Heating and Interstitial Heating

    OpenAIRE

    Saitoh, Yoshiaki; Hori, Junichi; 斉藤, 義明; 堀, 潤一

    2001-01-01

    Interstitial RF heating with an inserted electrode allows the heating position selection in a subject, but the narrow heating region is problematic. This study elucidates development of new interstitial RF heating methods, combining with external RF heating using paired electrodes, heating the subject broadly in advance in order to selectively extend the heating region. Two kinds of heating system were developed by controlling a differential mode and a common mode of RF currents. Heating expe...

  8. Evolutionary conservation of protein vibrational dynamics.

    Science.gov (United States)

    Maguid, Sandra; Fernandez-Alberti, Sebastian; Echave, Julian

    2008-10-01

    The aim of the present work is to study the evolutionary divergence of vibrational protein dynamics. To this end, we used the Gaussian Network Model to perform a systematic analysis of normal mode conservation on a large dataset of proteins classified into homologous sets of family pairs and superfamily pairs. We found that the lowest most collective normal modes are the most conserved ones. More precisely, there is, on average, a linear correlation between normal mode conservation and mode collectivity. These results imply that the previously observed conservation of backbone flexibility (B-factor) profiles is due to the conservation of the most collective modes, which contribute the most to such profiles. We discuss the possible roles of normal mode robustness and natural selection in the determination of the observed behavior. Finally, we draw some practical implications for dynamics-based protein alignment and classification and discuss possible caveats of the present approach.

  9. Survival of Listeria monocytogenes, Escherichia coli O157:H7, and Salmonella spp. on catfish fillets exposed to microwave heating in a continuous mode.

    Science.gov (United States)

    Sheen, Shiowshuh; Huang, Lihan; Sommers, Christopher

    2012-08-01

    Microwave (MW) heating using continuous power output with feedback control and a modified ingredient formulation may provide better and consistent cooking of foods. Currently, household units with build-in inverter power supply units are available. These new generation MW ovens provide continuous, adjustable output and cooking, in contrast to the traditional rectifier-based ovens that rely on the on-off mechanism for control. This study attempted to apply a feedback power control (termed as modified or "smart" MW oven) and phosphate treatment to further improve heating uniformity and enhance food quality and safety. Listeria monocytogenes (Lm, 4-strain cocktail), Escherichia coli O157:H7 (Ec, 5-strain cocktail), and Salmonella spp. (Sal, 6-strain cocktail), surface inoculated onto catfish fillets (75 × 100 × 15 mm; weight 110 g), were heated using the modified MW oven to study the inactivation of the pathogens. The sensitivity of these 3 bacteria to MW heating was in the order of Ec (most), Lm, and Sal (least). Greater than 4 to 5 log CFU reductions of Ec, Lm, or Sal counts on catfish fillet surfaces were inactivated within 2 min of 1250 W MW heating, where the fillet surface temperature increased from 10 to 20 °C to 80 to 90 °C. MW heating caused degradation of catfish fillet texture, which was noticeable as early as 10 to 15 s after the heating started, as evidenced by bumping sounds. Bumping can be significantly reduced by soaking fillets in phosphate solution. However, the results may need verification if applied in different MW ovens and/or with foods positioned away the geometric oven center. This study successfully demonstrated the feasibility of applying MW energy to eliminate foodborne pathogens on fish fillets. The results demonstrated in this report with the "smart" microwave oven design may enhance microwaveable food safety and quality, and therefore promote the microwaveable food business. © 2012 Institute of Food Technologists®

  10. Vibration analysis of cryocoolers

    Science.gov (United States)

    Tomaru, Takayuki; Suzuki, Toshikazu; Haruyama, Tomiyoshi; Shintomi, Takakazu; Yamamoto, Akira; Koyama, Tomohiro; Li, Rui

    2004-05-01

    The vibrations of Gifford-McMahon (GM) and pulse-tube (PT) cryocoolers were measured and analyzed. The vibrations of the cold-stage and cold-head were measured separately to investigate their vibration mechanisms. The measurements were performed while maintaining the thermal conditions of the cryocoolers at a steady state. We found that the vibration of the cold-head for the 4 K PT cryocooler was two orders of magnitude smaller than that of the 4 K GM cryocooler. On the other hand, the vibration of the cold-stages for both cryocoolers was of the same order of magnitude. From a spectral analysis of the vibrations and a simulation, we concluded that the vibration of the cold-stage is caused by an elastic deformation of the pulse tubes (or cylinders) due to the pressure oscillation of the working gas.

  11. Vibration analysis of cryocoolers

    Energy Technology Data Exchange (ETDEWEB)

    Tomaru, Takayuki; Suzuki, Toshikazu; Haruyama, Tomiyoshi; Shintomi, Takakazu; Yamamoto, Akira [High Energy Accelerator Research Organization (KEK), Tsukuba, Ibaraki (Japan); Koyama, Tomohiro; Rui Li [Sumitomo Heavy Industries Ltd., Tokyo (Japan)

    2004-05-01

    The vibrations of Gifford-McMahon (GM) and pulse-tube (PT) cryocoolers were measured and analyzed. The vibrations of the cold-stage and cold-head were measured separately to investigate their vibration mechanisms. The measurements were performed while maintaining the thermal conditions of the cryocoolers at a steady state. We found that the vibration of the cold-head for the 4 K PT cryocooler was two orders of magnitude smaller than that of the 4 K GM cryocooler. On the other hand, the vibration of the cold-stages for both cryocoolers was of the same order of magnitude. From a spectral analysis of the vibrations and a simulation, we concluded that the vibration of the cold-stage is caused by an elastic deformation of the pulse tubes (or cylinders) due to the pressure oscillation of the working gas. (Author)

  12. Vibration of hydraulic machinery

    CERN Document Server

    Wu, Yulin; Liu, Shuhong; Dou, Hua-Shu; Qian, Zhongdong

    2013-01-01

    Vibration of Hydraulic Machinery deals with the vibration problem which has significant influence on the safety and reliable operation of hydraulic machinery. It provides new achievements and the latest developments in these areas, even in the basic areas of this subject. The present book covers the fundamentals of mechanical vibration and rotordynamics as well as their main numerical models and analysis methods for the vibration prediction. The mechanical and hydraulic excitations to the vibration are analyzed, and the pressure fluctuations induced by the unsteady turbulent flow is predicted in order to obtain the unsteady loads. This book also discusses the loads, constraint conditions and the elastic and damping characters of the mechanical system, the structure dynamic analysis, the rotor dynamic analysis and the system instability of hydraulic machines, including the illustration of monitoring system for the instability and the vibration in hydraulic units. All the problems are necessary for vibration pr...

  13. Vibration analysis of composite laminate plate excited by piezoelectric actuators.

    Science.gov (United States)

    Her, Shiuh-Chuan; Lin, Chi-Sheng

    2013-03-01

    Piezoelectric materials can be used as actuators for the active vibration control of smart structural systems. In this work, piezoelectric patches are surface bonded to a composite laminate plate and used as vibration actuators. A static analysis based on the piezoelectricity and elasticity is conducted to evaluate the loads induced by the piezoelectric actuators to the host structure. The loads are then employed to develop the vibration response of a simply supported laminate rectangular plate excited by piezoelectric patches subjected to time harmonic voltages. An analytical solution of the vibration response of a simply supported laminate rectangular plate under time harmonic electrical loading is obtained and compared with finite element results to validate the present approach. The effects of location and exciting frequency of piezoelectric actuators on the vibration response of the laminate plate are investigated through a parametric study. Numerical results show that modes can be selectively excited, leading to structural vibration control.

  14. Development of Abnormal Operating Strategies for Loss of Ultimate Heat Sink (LOUHS) at Shutdown Mode in Westinghouse Type Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Duk-Joo; Lee, Seung-Chan; Sung, Je-Joong; Ha, Sang Jun [KHNP CRI, Daejeon (Korea, Republic of); Hwang, Su-Hyun [FNC Tech. Co., Yongin (Korea, Republic of)

    2016-10-15

    Loss of all AC power is classified as one of multiple failure accident by regulatory guide of Korean accident management program. Therefore we need develop strategies for the abnormal operating procedure both of power operating and shutdown mode. This paper developed abnormal operating guideline for loss of all AC power by analysis of accident scenario in pressurized water reactor. This paper analyzed the extended SBO in shutdown operating mode and developed the operating strategy of the abnormal operation procedure. Operator action for the emergency are not required to take in 500 minutes and 60 minutes in intact and opened RCS state respectively.

  15. Vibrational spectroscopy in the electron microscope.

    Science.gov (United States)

    Krivanek, Ondrej L; Lovejoy, Tracy C; Dellby, Niklas; Aoki, Toshihiro; Carpenter, R W; Rez, Peter; Soignard, Emmanuel; Zhu, Jiangtao; Batson, Philip E; Lagos, Maureen J; Egerton, Ray F; Crozier, Peter A

    2014-10-09

    Vibrational spectroscopies using infrared radiation, Raman scattering, neutrons, low-energy electrons and inelastic electron tunnelling are powerful techniques that can analyse bonding arrangements, identify chemical compounds and probe many other important properties of materials. The spatial resolution of these spectroscopies is typically one micrometre or more, although it can reach a few tens of nanometres or even a few ångströms when enhanced by the presence of a sharp metallic tip. If vibrational spectroscopy could be combined with the spatial resolution and flexibility of the transmission electron microscope, it would open up the study of vibrational modes in many different types of nanostructures. Unfortunately, the energy resolution of electron energy loss spectroscopy performed in the electron microscope has until now been too poor to allow such a combination. Recent developments that have improved the attainable energy resolution of electron energy loss spectroscopy in a scanning transmission electron microscope to around ten millielectronvolts now allow vibrational spectroscopy to be carried out in the electron microscope. Here we describe the innovations responsible for the progress, and present examples of applications in inorganic and organic materials, including the detection of hydrogen. We also demonstrate that the vibrational signal has both high- and low-spatial-resolution components, that the first component can be used to map vibrational features at nanometre-level resolution, and that the second component can be used for analysis carried out with the beam positioned just outside the sample--that is, for 'aloof' spectroscopy that largely avoids radiation damage.

  16. Performance Monitoring of Vibration in Belt Conveyor System

    Directory of Open Access Journals (Sweden)

    S.Ojha

    2014-07-01

    Full Text Available We are always using some kind of machines in our daily life starting from fan, refrigerator and washing machines at home. In case of industries of industrial machinery items condition monitoring is important to know onset impending defects. There are so many types of indicating phenomenon such as vibration, heat, debris in oil, noise and sounds which emanate from these in efficiently running machines. This paper presents the vibration related fault identification and maintenance of belt conveyor systems (BCS. After analyzing the spectrum and vibration readings, it was observed that a combination of parallel and angular misalignment between motor & gear box was present causing high axial and radial vibration. The defect was rectified by mechanical maintenance activities and latter the vibration was found reduced within limit. Also the vibration readings were taken after rectification. The above results are presented in this paper.

  17. Thermal vibrational convection in a two-phase stratified liquid

    Science.gov (United States)

    Chang, Qingming; Alexander, J. Iwan D.

    2007-05-01

    The response of a two-phase stratified liquid system subject to a vibration parallel to an imposed temperature gradient is analyzed using a hybrid thermal lattice Boltzmann method (HTLB). The vibrations considered correspond to sinusoidal translations of a rigid cavity at a fixed frequency. The layers are thermally and mechanically coupled. Interaction between gravity-induced and vibration-induced thermal convection is studied. The ability of the applied vibration to enhance the flow, heat transfer and interface distortion is investigated. For the range of conditions investigated, the results reveal that the effect of the vibrational Rayleigh number and vibrational frequency on a two-phase stratified fluid system is much different from that for a single-phase fluid system. Comparisons of the response of a two-phase stratified fluid system with a single-phase fluid system are discussed. To cite this article: Q. Chang, J.I.D. Alexander, C. R. Mecanique 335 (2007).

  18. Tuneable vibration absorber design to suppress vibrations: An application in boring manufacturing process

    Science.gov (United States)

    Moradi, H.; Bakhtiari-Nejad, F.; Movahhedy, M. R.

    2008-11-01

    Dynamic vibration absorbers are used to reduce the undesirable vibrations in many applications such as electrical transmission lines, helicopters, gas turbines, engines, bridges, etc. Tuneable vibration absorbers (TVA) are also used as semi-active controllers. In this paper, the application of a TVA for suppression of chatter vibrations in the boring manufacturing process is presented. The boring bar is modeled as a cantilever Euler-Bernoulli beam and the TVA is composed of mass, spring and dashpot elements. In addition, the effect of spring mass is considered in this analysis. After formulation of the problem, the optimum specifications of the absorber such as spring stiffness, absorber mass and its position are determined using an algorithm based on the mode summation method. The analog-simulated block diagram of the system is developed and the effects of various excitations such as step, ramp, etc. on the absorbed system are simulated. In addition, chatter stability is analyzed in dominant modes of boring bar. Results show that at higher modes, larger critical widths of cut and consequently more material removal rate (MRR) can be achieved. In the case of self-excited vibration, which is associated with a delay differential equation, the optimum absorber suppresses the chatter and increases the limit of stability.

  19. Impact of magnetic field and heating power on Er profile and fluctuations in I-mode pedestals in C-Mod

    Science.gov (United States)

    Hughes, Jerry; Wilks, T. M.; Theiler, C.; Hubbard, A. E.; Baek, S.-G.; Churchill, M.; Cziegler, I.; Edlund, E.; Rice, J.; Tolman, E.; C-Mod Team

    2017-10-01

    Cross machine comparisons of I-mode show robust stationary ELM suppressed plasmas over broad operating conditions, suggesting the potential for the regime to be utilized in future reactors. I-modes typically exhibit separation of particle and energy transport channels, often associated with the weakly coherent mode (WCM) coupled to a GAM-like fluctuation in the edge pedestal region. C-Mod I-mode pedestals are analyzed over varied magnetic fields (2.8-5.8T) and auxiliary power (1.5-4.6 MW) to determine trends in the edge radial electric field, ExB shear, rotation, and fluctuations. In a controlled power ramp, the radial electric field well increases with power before reaching its maximum before the I-H transition. With increased input power, preliminary observations show an increase in the fluctuation frequencies, followed by a frequency reversal associated with an increase in mid-spectrum fluctuations. Previous research has explored the L-I and I-H power thresholds dependence on plasma density, surface area and magnetic field, allowing us to examine pedestal ExB shear as a function of proximity to these thresholds. Work supported by the U.S. DOE under DE-FC02-99ER54512 and DE-SC0014264.

  20. Free vibrations of circular cylindrical shells

    CERN Document Server

    Armenàkas, Anthony E; Herrmann, George

    1969-01-01

    Free Vibrations of Circular Cylindrical Shells deals with thin-walled structures that undergo dynamic loads application, thereby resulting in some vibrations. Part I discusses the treatment of problems associated with the propagation of plane harmonic waves in a hollow circular cylinder. In such search for solutions, the text employs the framework of the three-dimensional theory of elasticity. The text explains the use of tables of natural frequencies and graphs of representative mode shapes of harmonic elastic waves bounding in an infinitely long isotropic hollow cylinder. The tables are