WorldWideScience

Sample records for vibrating frame grinder

  1. The Effect of a Mechanical Arm System on Portable Grinder Vibration Emissions.

    Science.gov (United States)

    McDowell, Thomas W; Welcome, Daniel E; Warren, Christopher; Xu, Xueyan S; Dong, Ren G

    2016-04-01

    Mechanical arm systems are commonly used to support powered hand tools to alleviate ergonomic stressors related to the development of workplace musculoskeletal disorders. However, the use of these systems can increase exposure times to other potentially harmful agents such as hand-transmitted vibration. To examine how these tool support systems affect tool vibration, the primary objectives of this study were to characterize the vibration emissions of typical portable pneumatic grinders used for surface grinding with and without a mechanical arm support system at a workplace and to estimate the potential risk of the increased vibration exposure time afforded by the use of these mechanical arm systems. This study also developed a laboratory-based simulated grinding task based on the ISO 28927-1 (2009) standard for assessing grinder vibrations; the simulated grinding vibrations were compared with those measured during actual workplace grinder operations. The results of this study demonstrate that use of the mechanical arm may provide a health benefit by reducing the forces required to lift and maneuver the tools and by decreasing hand-transmitted vibration exposure. However, the arm does not substantially change the basic characteristics of grinder vibration spectra. The mechanical arm reduced the average frequency-weighted acceleration by about 24% in the workplace and by about 7% in the laboratory. Because use of the mechanical arm system can increase daily time-on-task by 50% or more, the use of such systems may actually increase daily time-weighted hand-transmitted vibration exposures in some cases. The laboratory acceleration measurements were substantially lower than the workplace measurements, and the laboratory tool rankings based on acceleration were considerably different than those from the workplace. Thus, it is doubtful that ISO 28927-1 is useful for estimating workplace grinder vibration exposures or for predicting workplace grinder acceleration rank

  2. Assessment of vibration produced by the grinders used in the shipbuilding industry of Korea.

    Science.gov (United States)

    Park, Hee-Sok; Yim, Sang-Hyuk

    2007-04-01

    The objective of this study is to estimate the prevalence of finger blanching among the workers in a shipyard of Korea using the dose-response relationship suggested by ISO 5349. The characteristics of vibration exposure produced by six types of grinders were investigated. Vibration measurement was made under the real work conditions. Exposure time was estimated by questionnaire and direct observation. In addition, cold provocation tests were performed, and the results from the tests were compared with the estimated prevalence. As a result, 4 hour-energy-equivalent frequency-weighted accelerations of the finishing grinding (FG) and the prepainting grinding (PG) jobs were 6.23 m/s(2) and 13.39 m/s(2), respectively. The mean exposure time for holding the grinders was 4.64 h per day. Using the ISO 5349 method, it was predicted that after exposure to vibration for 10.79 yr, about a half of the FG workers could develop finger blanching. For the PG workers, the corresponding predicted latency was 5.02 yr. A discrepancy was found between the results from the ISO relationship and those from the cold provocation tests. A linear regression model was suggested employing vibration acceleration and vibration exposure time as explanatory variables for vascular dysfunction.

  3. Acute effects of vibration from a chipping hammer and a grinder on the hand-arm system.

    Science.gov (United States)

    Kihlberg, S; Attebrant, M; Gemne, G; Kjellberg, A

    1995-11-01

    The purpose of this study was to compare various effects on the hand-arm system of vibration exposure from a chipping hammer and a grinder with the same frequency weighted acceleration. Grip and push forces were measured and monitored during the exposure. The various effects were: muscle activity (measured with surface electrodes), discomfort ratings for different parts of the hand-arm system (made during and after exposure), and vibration perception threshold (for 10 minutes before and 10 minutes after the exposure). No increase in muscle activity due to exposure to vibration was found in the hand muscle studied. In the forearm, conversely, there was an increase in both muscle studied. For the upper arm the muscle activity only increased when exposed to impact vibration. Subjective ratings in the hand and shift in vibration perception threshold were effected more by the grinder than the hammer exposure. These results show that the reaction of the hand-arm system to vibration varies with frequency quantitatively as well as qualitatively. They do not support the notion that one single frequency weighted curve would be valid for the different health effects of hand-arm vibration (vascular, musculoskeletal, neurological, and psychophysiological).

  4. Frame junction vibration transmission with a modified frame deformation model.

    Science.gov (United States)

    Moore, J A

    1990-12-01

    A previous paper dealt with vibration transmission through junctions of connected frame members where the allowed frame deformations included bending, torsion, and longitudinal motions [J.A. Moore, J. Acoust. Soc. Am. 88, 2766-2776 (1990)]. In helicopter and aircraft structures the skin panels can constitute a high impedance connection along the length of the frames that effectively prohibits in-plane motion at the elevation of the skin panels. This has the effect of coupling in-plane bending and torsional motions within the frame. This paper discusses the transmission behavior through frame junctions that accounts for the in-plane constraint in idealized form by assuming that the attached skin panels completely prohibit inplane motion in the frames. Also, transverse shear deformation is accounted for in describing the relatively deep web frame constructions common in aircraft structures. Longitudinal motion in the frames is not included in the model. Transmission coefficient predictions again show the importance of out-of-plane bending deformation to the transmission of vibratory energy in an aircraft structure. Comparisons are shown with measured vibration transmission data along the framing in the overhead of a helicopter airframe, with good agreement. The frame junction description has been implemented within a general purpose statistical energy analysis (SEA) computer code in modeling the entire airframe structure including skin panels.

  5. Biodetection grinder

    Science.gov (United States)

    Beyerle, F. J.

    1974-01-01

    Grinder, which employs shearing action with minimum energy input, obtains desired particle sizes in materials ranging from soft plastics to hard rocks. Modified version of this grinder might be used in hospitals and biological laboratories involved with bacteriological research and testing.

  6. Pedestal Grinder.

    Science.gov (United States)

    Engelbrecht, Nancy; And Others

    These instructional materials provide an orientation to the pedestal grinder for use at the postsecondary level. The first of eight sections defines 14 important terms. The second section outlines 16 rules for safe use of the pedestal grinder. The third section covers grinding wheels for five different types of materials. The fourth section…

  7. Sound insulation and vibration tests for lightweight steel framing floors

    OpenAIRE

    Shi, Wanqing; Edfast, Fredrik; Ågren, Anders

    2000-01-01

    An experimental study of sound insulation and vibrations of lightweight steel framing floors due to different floor construction set up were performed. Floors with 3m, 5m and 7.2m span were tested. The impact and airborne sound insulation for 3m span floor were measured based on ISO 140 in lab condition. Vibration tests were carried out on all three different spans. The vibration transmission loss of the structure was determined from the surface vibration measurements. The fundamental natural...

  8. Vibration measurements on timber frame floors

    NARCIS (Netherlands)

    Kuilen, J.W.G. van de; Oosterhout, G.P.C. van; Donkervoort, R.

    1998-01-01

    In the design of lightweight floors vibrational aspects become more and more important. With the foreseen introduction of Eurocode 5 the vibration of timber floors becomes a part of the design for serviceability. Design rules for the vibrational behaviour are given in Eurocode 5. The first rule is

  9. [The combined action of intermittent vibration and physical loads (exemplified by the grinder-buffers of turbine vanes)].

    Science.gov (United States)

    Butovskaia, Z M; Ornitsan, E Iu; Kirikova, G A; Smirnov, V V

    1995-01-01

    The article presents hygienic evaluation of interrupted vibration in grinding of turbine vanes by stationary machines with consideration of static and dynamic load. Criteria estimating the operation are set, clinical features of the occupational diseases are determined.

  10. VIBRATION OF FRAME BUILDING STRUCTURES CAUSED BY UNDERGROUND TRAINS

    Directory of Open Access Journals (Sweden)

    P. V. Аliavdin

    2011-01-01

    Full Text Available The paper contains investigations on element vibration of a real residential 9-storeyed reinforced-concrete frame building induced by train movement in the shallow subway. A design model for a problem on propagation of bending waves within the limits of the typical fragment of a skeleton is presented in the paper. The steady state vibrations of a column and reinforced-concrete slab induced by an excited force which is equivalent to the impact of the subway trains have been investigated in the paper. The problem has been solved numerically on the basis of the ANSYS FEA program. Numerical results have been compared with an approximate analytical solution and data on full-scale experiment. A prediction technique for vibration propagation in the designed buildings is offered in the paper. 

  11. NASTRAN nonlinear vibration analysis of beam and frame structures

    Science.gov (United States)

    Mei, C.; Rogers, J. L., Jr.

    1975-01-01

    A capability for the nonlinear vibration analysis of beam and frame structures suitable for use with NASTRAN level 15.5 is described. The nonlinearity considered is due to the presence of axial loads induced by longitudinal end restraints and lateral displacements that are large compared to the beam height. A brief discussion is included of the mathematical analysis and the geometrical stiffness matrix for a prismatic beam (BAR) element. Also included are a brief discussion of the equivalent linearization iterative process used to determine the nonlinear frequency, the required modifications to subroutines DBAR and XMPLBD of the NASTRAN code, and the appropriate vibration capability, four example problems are presented. Comparisons with existing experimental and analytical results show that excellent accuracy is achieved with NASTRAN in all cases.

  12. Machine Shop. Module 7: Grinders. Instructor's Guide.

    Science.gov (United States)

    Nobles, Jack; Gage, Mel

    This document consists of materials for an eight-unit course on the following topics: (1) grinder safety and types of grinders; (2) surface grinder accessories and equipment maintenance; (3) surface grinder preparation and set-up; (4) surface grinding flat and angular surfaces; (5) cylindrical grinding; (6) tool and cutter safety; (7) tool and…

  13. Free vibrations of thin-walled semicircular graphite-epoxy composite frames

    Science.gov (United States)

    Noor, Ahmed K.; Carden, Huey D.; Peters, Jeanne M.

    1991-01-01

    A detailed study is made of the effects of variations in lamination and material parameters of thin-walled composite frames on their vibrational characteristics. The structures considered are semicircular thin-walled frames with I and J sections. The flanges and webs of the frames are modeled by using two-dimensional shell and plate finite elements. A mixed formulation is used with the fundamental unknowns consisting of both the generalized displacements and stress resultants in the frame. The frequencies and modes predicted by the two-dimensional finite-element model are compared with those obtained from experiments, as well as with the predictions of a one-dimensional, thin-walled-beam, finite-element model. A detailed study is made of the sensitivity of the vibrational response to variations in the fiber orientation, material properties of the individual layers, and boundary conditions.

  14. Vibration-based localisation of structural deterioration in frame-like civil engineering structures

    DEFF Research Database (Denmark)

    Ulriksen, Martin Dalgaard; Damkilde, Lars

    2016-01-01

    to other structural systems, for instance, wind turbines—can provide reliable damage localisation in frame-like structures. The performance of the method, which is based on statistical interrogation of changes in a surrogate of the transfer matrix, is tested in a Monte Carlo setting with a numerical steel......With the existing trend of minimising material use in typical frame-like civil engineering structures, such as buildings, bridges, and offshore platforms, these structures will typically be subjected to substantial wind induced vibrations. Besides being a source of disturbance for the occupants...... frame model subjected to white noise excitation....

  15. Pixel-Level and Robust Vibration Source Sensing in High-Frame-Rate Video Analysis

    Directory of Open Access Journals (Sweden)

    Mingjun Jiang

    2016-11-01

    Full Text Available We investigate the effect of appearance variations on the detectability of vibration feature extraction with pixel-level digital filters for high-frame-rate videos. In particular, we consider robust vibrating object tracking, which is clearly different from conventional appearance-based object tracking with spatial pattern recognition in a high-quality image region of a certain size. For 512 × 512 videos of a rotating fan located at different positions and orientations and captured at 2000 frames per second with different lens settings, we verify how many pixels are extracted as vibrating regions with pixel-level digital filters. The effectiveness of dynamics-based vibration features is demonstrated by examining the robustness against changes in aperture size and the focal condition of the camera lens, the apparent size and orientation of the object being tracked, and its rotational frequency, as well as complexities and movements of background scenes. Tracking experiments for a flying multicopter with rotating propellers are also described to verify the robustness of localization under complex imaging conditions in outside scenarios.

  16. Low-frequency and wideband vibration energy harvester with flexible frame and interdigital structure

    Energy Technology Data Exchange (ETDEWEB)

    Li, Pengwei, E-mail: lipengwei@tyut.edu.cn; Wang, Yanfen; Luo, Cuixian; Li, Gang; Hu, Jie; Zhang, Wendong [MicroNano System Research Center of College of Information Engineering and Key Lab of Advanced Transducers and Intelligent Control System of the Ministry of Education, Taiyuan University of Technology, Taiyuan 030024, Shanxi (China); Liu, Ying [MicroNano System Research Center of College of Information Engineering and Key Lab of Advanced Transducers and Intelligent Control System of the Ministry of Education, Taiyuan University of Technology, Taiyuan 030024, Shanxi (China); Baicheng Ordnance Test Center of China, Baicheng 137000, Jilin (China); Liu, Wei [Baicheng Ordnance Test Center of China, Baicheng 137000, Jilin (China)

    2015-04-15

    As an alternative to traditional cantilever beam structures and their evolutions, a flexible beam based, interdigital structure, vibration energy harvester has been presented and investigated. The proposed interdigital-shaped oscillator consists of a rectangular flexible frame and series of cantilever beams interdigitally bonded to it. In order to achieve low frequency and wide-bandwidth harvesting, Young’s modulus of materials, frame size and the amount of the cantilevers have been studied systematically. The measured frequency responses of the designed device (PDMS frame, quintuple piezoelectric cantilever beams) show a 460% increase in bandwidth below 80Hz. When excited at an acceleration of 1.0 g, the energy harvester achieves to a maximum open-circuit voltage of 65V, and the maximum output power 4.5 mW.

  17. Low-frequency and wideband vibration energy harvester with flexible frame and interdigital structure

    Directory of Open Access Journals (Sweden)

    Pengwei Li

    2015-04-01

    Full Text Available As an alternative to traditional cantilever beam structures and their evolutions, a flexible beam based, interdigital structure, vibration energy harvester has been presented and investigated. The proposed interdigital-shaped oscillator consists of a rectangular flexible frame and series of cantilever beams interdigitally bonded to it. In order to achieve low frequency and wide-bandwidth harvesting, Young’s modulus of materials, frame size and the amount of the cantilevers have been studied systematically. The measured frequency responses of the designed device (PDMS frame, quintuple piezoelectric cantilever beams show a 460% increase in bandwidth below 80Hz. When excited at an acceleration of 1.0 g, the energy harvester achieves to a maximum open-circuit voltage of 65V, and the maximum output power 4.5 mW.

  18. Prediction and mitigation analysis of ground vibration caused by running high-speed trains on rigid-frame viaducts

    Science.gov (United States)

    Sun, Liangming; Xie, Weiping; He, Xingwen; Hayashikawa, Toshiro

    2016-03-01

    In this study a 3D numerical analysis approach is developed to predict the ground vibration around rigid-frame viaducts induced by running high-speed trains. The train-bridge-ground interaction system is divided into two subsystems: the train-bridge interaction and the soil-structure interaction. First, the analytical program to simulate bridge vibration with consideration of train-bridge interaction is developed to obtain the vibration reaction forces at the pier bottoms. The highspeed train is described by a multi-DOFs vibration system and the rigid-frame viaduct is modeled with 3D beam elements. Second, applying these vibration reaction forces as input external excitations, the ground vibration is simulated by using a general-purpose program that includes soil-structure interaction effects. The validity of the analytical procedure is confirmed by comparing analytical and experimental results. The characteristics of high-speed train-induced vibrations, including the location of predominant vibration, are clarified. Based on this information a proposed vibration countermeasure using steel strut and new barrier is found effective in reducing train-induced vibrations and it satisfies environmental vibration requirements. The vibration screening efficiency is evaluated by reduction VAL based on 1/3 octave band spectral analysis.

  19. Synchronization of Two Self-Synchronous Vibrating Machines on an Isolation Frame

    Directory of Open Access Journals (Sweden)

    Chunyu Zhao

    2011-01-01

    Full Text Available This paper investigates synchronization of two self-synchronous vibrating machines on an isolation rigid frame. Using the modified average method of small parameters, we deduce the non-dimensional coupling differential equations of the disturbance parameters for the angular velocities of the four unbalanced rotors. Then the stability problem of synchronization for the four unbalanced rotors is converted into the stability problems of two generalized systems. One is the generalized system of the angular velocity disturbance parameters for the four unbalanced rotors, and the other is the generalized system of three phase disturbance parameters. The condition of implementing synchronization is that the torque of frequency capture between each pair of the unbalanced rotors on a vibrating machine is greater than the absolute values of the output electromagnetic torque difference between each pair of motors, and that the torque of frequency capture between the two vibrating machines is greater than the absolute value of the output electromagnetic torque difference between the two pairs of motors on the two vibrating machines. The stability condition of synchronization of the two vibrating machines is that the inertia coupling matrix is definite positive, and that all the eigenvalues for the generalized system of three phase disturbance parameters have negative real parts. Computer simulations are carried out to verify the results of the theoretical investigation.

  20. Earthquake and ambient vibration monitoring of the steel-frame UCLA factor building

    Science.gov (United States)

    Kohler, M.D.; Davis, P.M.; Safak, E.

    2005-01-01

    Dynamic property measurements of the moment-resisting steel-frame University of California, Los Angeles, Factor building are being made to assess how forces are distributed over the building. Fourier amplitude spectra have been calculated from several intervals of ambient vibrations, a 24-hour period of strong winds, and from the 28 March 2003 Encino, California (ML = 2.9), the 3 September 2002 Yorba Linda, California (ML = 4.7), and the 3 November 2002 Central Alaska (Mw = 7.9) earthquakes. Measurements made from the ambient vibration records show that the first-mode frequency of horizontal vibration is between 0.55 and 0.6 Hz. The second horizontal mode has a frequency between 1.6 and 1.9 Hz. In contrast, the first-mode frequencies measured from earthquake data are about 0.05 to 0.1 Hz lower than those corresponding to ambient vibration recordings indicating softening of the soil-structure system as amplitudes become larger. The frequencies revert to pre-earthquake levels within five minutes of the Yorba Linda earthquake. Shaking due to strong winds that occurred during the Encino earthquake dominates the frequency decrease, which correlates in time with the duration of the strong winds. The first shear wave recorded from the Encino and Yorba Linda earthquakes takes about 0.4 sec to travel up the 17-story building. ?? 2005, Earthquake Engineering Research Institute.

  1. Fault Diagnosis for Centre Wear Fault of Roll Grinder Based on a Resonance Demodulation Scheme

    Science.gov (United States)

    Wang, Liming; Shao, Yimin; Yin, Lei; Yuan, Yilin; Liu, Jing

    2017-05-01

    Roll grinder is one of the important parts in the rolling machinery, and the grinding precision of roll surface has direct influence on the surface quality of steel strip. However, during the grinding process, the centre bears the gravity of the roll and alternating stress. Therefore, wear or spalling faults are easily observed on the centre, which will lead to an anomalous vibration of the roll grinder. In this study, a resonance demodulation scheme is proposed to detect the centre wear fault of roll grinder. Firstly, fast kurtogram method is employed to help select the sub-band filter parameters for optimal resonance demodulation. Further, the envelope spectrum are derived based on the filtered signal. Finally, two health indicators are designed to conduct the fault diagnosis for centre wear fault. The proposed scheme is assessed by analysing experimental data from a roll grinder of twenty-high rolling mill. The results show that the proposed scheme can effectively detect the centre wear fault of the roll grinder.

  2. Seismic Vibration Control of 3D Steel Frames with Irregular Plans Using Eccentrically Placed MR Dampers

    Directory of Open Access Journals (Sweden)

    Yuwen Hu

    2017-07-01

    Full Text Available There has been a significant increase in attention toward designing smart structures and vibration control of structures in recent decades, and numerous methods and algorithms have been developed and experimentally investigated. However, the majority of these studies used the shear frame models to represent structures. Since the simplified models do not reflect the realistic behavior of those structures with irregularity in plan and elevation, the traditional methods for designing an optimal control that guarantees a desirable performance is impossible. In this study, the behavior of a 10-story irregular steel frame building is investigated with and without controlling systems. Two pairs of eccentrically placed MR dampers on each story are used in order to mitigate the coupled translational–torsional vibration. The controlling forces are determined using active, passive-off, passive-on, and clipped optimal controls based on the linear quadratic regulator (LQR algorithm. The results demonstrate that using pairs of magneto-rheological (MR dampers with an appropriate distance on lower story levels significantly reduces the inter-story drifts for the corner columns, as well as the roof displacements and accelerations.

  3. Effect of Wheelchair Frame Material on Users' Mechanical Work and Transmitted Vibration

    Science.gov (United States)

    Aissaoui, Rachid

    2014-01-01

    Wheelchair propulsion exposes the user to a high risk of shoulder injury and to whole-body vibration that exceeds recommendations of ISO 2631-1:1997. Reducing the mechanical work required to travel a given distance (WN-WPM, weight-normalized work-per-meter) can help reduce the risk of shoulder injury, while reducing the vibration transmissibility (VT) of the wheelchair frame can reduce whole-body vibration. New materials such as titanium and carbon are used in today's wheelchairs and are advertised to improve both parameters, but current knowledge on this matter is limited. In this study, WN-WPM and VT were measured simultaneously and compared between six folding wheelchairs (1 titanium, 1 carbon, and 4 aluminium). Ten able-bodied users propelled the six wheelchairs on three ground surfaces. Although no significant difference of WN-WPM was found between wheelchairs (P < 0.1), significant differences of VT were found (P < 0.05). The carbon wheelchair had the lowest VT. Contrarily to current belief, the titanium wheelchair VT was similar to aluminium wheelchairs. A negative correlation between VT and WN-WPM was found, which means that reducing VT may be at the expense of increasing WN-WPM. Based on our results, use of carbon in wheelchair construction seems promising to reduce VT without increasing WN-WPM. PMID:25276802

  4. Study on Frame Vibration Suppression Control Method for Position Sensorless drive System of Permanent Magnet Synchronous Motor

    OpenAIRE

    Supharat, Suthep

    2016-01-01

    Permanent magnet synchronous motor has been widely used in variable speed drive system for various fields, such as industry, household applications, etc., The merits of PMSM are rugged construction, high efficiency, high torque to current ratio, low inertia, etc. Recently, PMSM driven air-conditioners and refrigerators are obviously increased. However, the compressors used in the air-conditioners have the problem that vibration occurs due to the torque pulsation. The frame vibration results i...

  5. Processing woody biomass with a modified horizontal grinder

    Science.gov (United States)

    Dana Mitchell; John Klepac

    2008-01-01

    This study documents the production rate and cost of producing woody biomass chips for use in a power plant. The power plant has specific raw material handling requirements. Output from a 3-knife chipper, a tub grinder, and a horizontal grinder was considered. None of the samples from these machines met the specifications needed. A horizontal grinder was modified to...

  6. 33 CFR 151.75 - Grinders or comminuters.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Grinders or comminuters. 151.75... Treaty as it Pertains to Pollution from Ships Garbage Pollution and Sewage § 151.75 Grinders or comminuters. Each grinder or comminuter used to discharge garbage in accordance with § 151.69(a)(2) or § 151...

  7. 7 CFR 58.708 - Grinders or shredders.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Grinders or shredders. 58.708 Section 58.708 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....708 Grinders or shredders. The grinders or shredders used in the preparation of the trimmed and...

  8. Meat grinder injuries to the upper extremity.

    Science.gov (United States)

    Brandner, M; Bunkis, J; Trengove-Jones, G

    1985-05-01

    Three cases of hand injury caused by meat grinders are presented. All 3 injuries involved the dominant hand and resulted in varying degrees of deformity. Two of the 3 patients arrived in the emergency room with the injured hand still firmly wedged in the meat grinder. Although these injuries continue to prove very mutilating, maximum restoration of the injured hand can be accomplished by careful extrication, followed by preservation and reconstruction of all viable tissues. Perioperative antibiotics and wound irrigation with antibiotic solution are recommended. Microsurgical technique can be of value in treating selected patients.

  9. Gas tungsten arc welder with electrode grinder

    Science.gov (United States)

    Christiansen, David W.; Brown, William F.

    1984-01-01

    A welder for automated closure of fuel pins by a gas tungsten arc process in which a rotating length of cladding is positioned adjacent a welding electrode in a sealed enclosure. An independently movable axial grinder is provided in the enclosure for refurbishing the used electrode between welds.

  10. Air Guide for Sheet-Metal Grinder

    Science.gov (United States)

    Heermann, T.

    1984-01-01

    Tool attachment reduces heat distortion of sheet. Air-guide attachment directs air from grinder motor to grinding wheel and metal sheet being ground. Cooling air reduces thermal distortion of workpiece due to localized frictional heating. Particularly useful when grinding sheet metal.

  11. [Morphologic aspects of angle grinder injury].

    Science.gov (United States)

    Thurner, W; Pollak, S

    1989-01-01

    Experiments were conducted on soft-tissue and bone preparations to determine the morphological characteristics of angle grinder injuries. The grinding effect of the rotating cutting-off wheel causes severances with local loss of tissue, resulting in tool-specific wound features. Superficial skin notches and (incomplete) severances of bony structures are of particular significance. Mutual trace transfer is a valuable means for determining the tool used and for interpreting the scene.

  12. Performing in-feed type centerless grinding process on a surface grinder

    Science.gov (United States)

    Xu, W.; Wu, Y.; Sato, T.; Lin, W.

    2011-01-01

    In our previous study, a new centerless grinding method using surface grinder was proposed. In this method, centerless grinding operations are performed by installing a compact centerless grinding unit, consisting mainly of an ultrasonic elliptic-vibration shoe, a blade and their respective holders, on the worktable of a surface grinder. During grinding, the cylindrical workpiece is held on the ultrasonic shoe and the blade, and its rotational motion is controlled by the elliptic motion of the shoe end-face. An actual unit had been produced and its performance in tangential-feed type centerless grinding using a surface grinder had been confirmed in the previous workd. In this paper, the performance of the grinding unit in in-feed centerless grinding operation was confirmed, and the effects of the main process parameter, i.e., eccentric angle, on the workpiece roundness was investigated experimentally. The obtained results showed that: (1) the centerless grinding unit performed well in in-feed type centerless grinding; (2) the eccentric angle affects roundness significantly, and its optimal angle is 6°; (3) the workpiece roundness can be further improved by varying the eccentric angle during grinding, and the final roundness reached 0.65 μm after grinding as the eccentric angle varied from 9° to 6° and to 3°.

  13. Extrication of the hand from a meat grinder.

    Science.gov (United States)

    Green, D P; Terry, G C; Whittemore, A K

    1975-01-01

    A case is presented in which a patient arrived in the emergency room with his forearm firmly entrapped in a large commercial meat grinder. The arm was extricated without sacrificing additional forearm stump length by reversing the worm mechanism of the meat grinder.

  14. Accidental ligature strangulation due to electric grinder.

    Science.gov (United States)

    Shetty, Mahabalesh; Shetty, B Suresh

    2006-04-01

    A young girl was accidentally strangled when her chunni (a piece of cloth worn around the neck by most Indian women) was caught in a moving electrical grinder. She was taken to the nearest hospital where she died within the next 9h, remaining unconscious throughout the hospital stay. Accidental strangulation of this kind due to household devices or machinery is extremely uncommon and to the best of our knowledge, this is the first case of its kind to be reported. The findings are presented.

  15. Fatigue and Model Analysis of the CNC Cylindrical Grinder

    Directory of Open Access Journals (Sweden)

    Lin Jui-Chang

    2016-01-01

    Full Text Available The purpose of this study is to lower deviation of workpiece by meeting high stability and rigidity to prevent the resonance in producing procedure of the CNC universal cylindrical grinding machine. Using finite element analysis software ABAQUS in grinder machine tools for numerical simulation of several analyses for the following: structural rigidity analysis, optimized design, vibration frequency analysis and fatigue damage analysis. This work aims on state of the transmission of outer diameter spindle to proceed in stress and fatigue life analysis by FE-SAFE Subroutine. The max values of equivalent stress and average amount of displacement in structural rigidity analysis are 0.67(Mpa and 0.92(µm. Optimization design effectively reducing extreme value of stress, the largest decline of about 5.43%. Modal analysis compared with the experimental, the average error percentage was less than 10% of parts. The whole structure error does not exceed 3%. The fatigue life of approximately 1,193,988 times, estimates into real life time can use more than sixty years, from the viewpoint of structural strength, spindle has a good high breaking strength is designed to be safe.

  16. Penetrating facial injury from angle grinder use: management and prevention

    Directory of Open Access Journals (Sweden)

    Varley Iain

    2008-01-01

    Full Text Available Abstract Injuries resulting from the use of angle grinders are numerous. The most common sites injured are the head and face. The high speed disc of angle grinders does not respect anatomical boundaries or structures and thus the injuries produced can be disfiguring, permanently disabling or even fatal. However, aesthetically pleasing results can be achieved with thorough debridement, resection of wound edges and careful layered functional closure after reduction and fixation of facial bone injuries. A series of penetrating facial wounds associated with angle grinder use are presented and the management and prevention of these injuries discussed.

  17. Penetrating facial injury from angle grinder use: management and prevention.

    Science.gov (United States)

    Carter, Lachlan M; Wales, Craig J; Varley, Iain; Telfer, Martin R

    2008-01-23

    Injuries resulting from the use of angle grinders are numerous. The most common sites injured are the head and face. The high speed disc of angle grinders does not respect anatomical boundaries or structures and thus the injuries produced can be disfiguring, permanently disabling or even fatal. However, aesthetically pleasing results can be achieved with thorough debridement, resection of wound edges and careful layered functional closure after reduction and fixation of facial bone injuries. A series of penetrating facial wounds associated with angle grinder use are presented and the management and prevention of these injuries discussed.

  18. [Measurement and analysis of hand-transmitted vibration of vibration tools in workplace for automobile casting and assembly].

    Science.gov (United States)

    Xie, X S; Qi, C; Du, X Y; Shi, W W; Zhang, M

    2016-02-20

    To investigate the features of hand-transmitted vibration of common vibration tools in the workplace for automobile casting and assembly. From September to October, 2014, measurement and spectral analysis were performed for 16 typical hand tools(including percussion drill, pneumatic wrench, grinding machine, internal grinder, and arc welding machine) in 6 workplaces for automobile casting and assembly according to ISO 5349-1-2001 Mechanical vibration-Measurement and evaluation of human exposure to hand-transmitted vibration-part 1: General requirements and ISO 5349-2-2001 Mechanical vibration-Measurement and evaluation of human exposure to hand-transmitted vibration-Part 2: Practical guidance for measurement in the workplace. The vibration acceleration waveforms of shearing machine, arc welding machine, and pneumatic wrench were mainly impact wave and random wave, while those of internal grinder, angle grinder, percussion drill, and grinding machine were mainly long-and short-period waves. The daily exposure duration to vibration of electric wrench, pneumatic wrench, shearing machine, percussion drill, and internal grinder was about 150 minutes, while that of plasma cutting machine, angle grinder, grinding machine, bench grinder, and arc welding machine was about 400 minutes. The range of vibration total value(ahv) was as follows: pneumatic wrench 0.30~11.04 m/s(2), grinding wheel 1.61~8.97 m/s(2), internal grinder 1.46~8.70 m/s(2), percussion drill 11.10~14.50 m/s(2), and arc welding machine 0.21~2.18 m/s(2). The workers engaged in cleaning had the longest daily exposure duration to vibration, and the effective value of 8-hour energy-equivalent frequency-weighted acceleration for them[A(8)] was 8.03 m/s(2), while this value for workers engaged in assembly was 4.78 m/s(2). The frequency spectrogram with an 1/3-time frequency interval showed that grinding machine, angle grinder, and percussion drill had a high vibration acceleration, and the vibration limit curve

  19. Penetrating head injury from angle grinder: A cautionary tale

    OpenAIRE

    S SenthilKumaran; N Balamurgan; Arthanari, K; Thirumalaikolundusubramanian, P

    2010-01-01

    Penetrating cranial injury is a potentially life-threatening condition. Injuries resulting from the use of angle grinders are numerous and cause high-velocity penetrating cranial injuries. We present a series of two penetrating head injuries associated with improper use of angle grinder, which resulted in shattering of disc into high velocity missiles with reference to management and prevention. One of those hit on the forehead of the operator and the other on the occipital region of the co-w...

  20. Penetrating facial injury from angle grinder use: management and prevention

    OpenAIRE

    Varley Iain; Wales Craig J; Carter Lachlan M; Telfer Martin R

    2008-01-01

    Abstract Injuries resulting from the use of angle grinders are numerous. The most common sites injured are the head and face. The high speed disc of angle grinders does not respect anatomical boundaries or structures and thus the injuries produced can be disfiguring, permanently disabling or even fatal. However, aesthetically pleasing results can be achieved with thorough debridement, resection of wound edges and careful layered functional closure after reduction and fixation of facial bone i...

  1. Meat Grinder Injury to the Hand: Serial Cases

    OpenAIRE

    Lubis, Nur Rachmat

    2012-01-01

    Introduction.Although meat grinder injury to the hand is not a common case, it causes a wide spectrum of injuries that result not only in tremendous physical and emotional pain but also substantial economic impact as well.Case presentation.Three cases of hand injury caused by meat grinders are presented. Two injuries involved non dominant hand and one involved dominant hand, result in varying degrees of deformity. All patients arrived in emergency room with injured hand still firmly...

  2. Experimental Studies on Damage Detection in Frame Structures Using Vibration Measurements

    Directory of Open Access Journals (Sweden)

    Giancarlo Fraraccio

    2010-01-01

    Full Text Available This paper presents an experimental study of frequency and time domain identification algorithms and discusses their effectiveness in structural health monitoring of frame structures using acceleration input and response data. Three algorithms were considered: 1 a frequency domain decomposition algorithm (FDD, 2 a time domain Observer Kalman IDentification algorithm (OKID, and 3 a subsequent physical parameter identification algorithm (MLK. Through experimental testing of a four-story steel frame model on a uniaxial shake table, the inherent complications of physical instrumentation and testing are explored. Primarily, this study aims to provide a dependable first-order and second-order identification of said test structure in a fully instrumented state. Once the characteristics (i.e. the stiffness matrix for a benchmark structure have been determined, structural damage can be detected by a change in the identified structural stiffness matrix. This work also analyzes the stability of the identified structural stiffness matrix with respect to fluctuations of input excitation magnitude and frequency content in an experimental setting.

  3. Development of two-stage grain grinder

    Directory of Open Access Journals (Sweden)

    V. N. Trubnikov

    2016-01-01

    Full Text Available The most important task in the development of the diet of farm animals feeding is a selection of the most balanced in its composition and most nutritious feeds, which are safe and meet all the necessary requirements at the same time. To evaluate the productive value of feeds and their effectiveness the rate of food productive action η was proposed. This ratio reflects the productive part of the total value of the exchange energy of the daily feed ration and is an essential criterion of the feed quality indicators. In the feed rations of animals the most expensive, but energy-rich feed is a mixed fodder, a mixture of grinded seeds of agricultural crops and protein, mineral and vitamin additives. In the diet for its nutritional value, this feed product is for cattle – 50, pigs – 60… 100 and birds – 100%. The basic operation in the production of mixed fodder is seeds grinding, i.e. their destruction under the influence of external forces, exceeding the forces of molecular adhesion of the grains particles. To grind the grain different ways are used: chopping, grinding, impact «in flight», crushing, etc. In the production of mixed fodder on the existing production equipment, there is the problem of getting the grain mixed fodder the necessary degree of grinding and uniform in its particle size distribution at the same time. When receiving too coarse grinding there is a problem of difficult digestibility of mixed fodder by farm animals. Moreover grinding process is accompanied by a high energy consumption. Grain grinder, the principle of which is based on the implementation of two ways of grinding grain: splitting and impact «in flight» is proposed. The proposed constructive solutions allow to obtain a high-performance technical means for crushing seeds of crops, as well as reduce energy costs that arise during the course of the process of obtaining of mixed fodder. The methodology justification of degree of grain grinding by

  4. Grinder: a versatile amplicon and shotgun sequence simulator.

    Science.gov (United States)

    Angly, Florent E; Willner, Dana; Rohwer, Forest; Hugenholtz, Philip; Tyson, Gene W

    2012-07-01

    We introduce Grinder (http://sourceforge.net/projects/biogrinder/), an open-source bioinformatic tool to simulate amplicon and shotgun (genomic, metagenomic, transcriptomic and metatranscriptomic) datasets from reference sequences. This is the first tool to simulate amplicon datasets (e.g. 16S rRNA) widely used by microbial ecologists. Grinder can create sequence libraries with a specific community structure, α and β diversities and experimental biases (e.g. chimeras, gene copy number variation) for commonly used sequencing platforms. This versatility allows the creation of simple to complex read datasets necessary for hypothesis testing when developing bioinformatic software, benchmarking existing tools or designing sequence-based experiments. Grinder is particularly useful for simulating clinical or environmental microbial communities and complements the use of in vitro mock communities.

  5. Vibration characteristics of walls and a plate glass window representative of those of a wood-frame house

    Science.gov (United States)

    Carden, H. D.

    1979-01-01

    Mechanical excitation was used, and measurements of acceleration response, natural frequencies, and nodal patterns were performed. Results indicate that the wall sections and the complete wall did not act as a unit in responding to sinusoidal vibration inputs. Calculated frequencies of the components that account for this independent behavior of the studs and face sheets agreed resonably well with experimental frequencies. Experimental vibrations of the plate glass window agreed with the calculated behavior, and responses of the window exposed to airplane flyover noise were readily correlated with the test results.

  6. Angle grinder injuries: a cause of serious head and neck trauma.

    Science.gov (United States)

    Wongprasartsuk, S; Love, R L; Cleland, H J

    2000-03-20

    Over the past 12 months, the Victorian Trauma Centre at the Alfred Hospital, Melbourne, has dealt with serious head and neck injuries associated with angle grinder use. Three cases are presented, documenting the circumstances and severity of these injuries and subsequent management. Angle grinder injuries are a source of serious morbidity and mortality, much of which is preventable.

  7. Fatal cranial injuries caused by an electric angle grinder.

    Science.gov (United States)

    Telmon, N; Allery, J P; Scolan, V; Rougé, D

    2001-03-01

    A case of fatal cranial injuries caused by an angle grinder is reported. The scalp lesions were typical of those produced by a cutting disk in a side-slipping movement. On the cranial vault were two bony losses of substance, one of which was deep enough for intracranial penetration of the disk. Signs of deflection of the disk, identical to those found on the scalp, were observed on the external bony table. Because of the circumstances in which the victim was discovered, in particular the damage to the machine which had a broken handle, and the lack of any indication of homicide or suicide, an accident is the most likely hypothesis.

  8. Active monitoring as cognitive control of grinders design

    Science.gov (United States)

    Flizikowski, Jozef B.; Mrozinski, Adam; Tomporowski, Andrzej

    2017-03-01

    A general monitoring methodology applicable to plastics recyclates grinding processes development for energy engineering, has been presented in this work. The method includes two beings: mathematical aiding an invention and working of a novelty. The common set is composed of characteristics, structure, relationships of knowledge about states and transformations, effectiveness and progress of the devices and machinery engineering, e.g. breaking up in the energy-materials recycling process. This innovations theory is identified by the valuation, estimation, testing and creative archiving the elaborated character and structure of the invention and grinders construction development.

  9. Vibration analysis of doubly asymmetric, three-dimensional structures comprising wall and frame assemblies with variable cross-section

    Science.gov (United States)

    Rafezy, B.; Howson, W. P.

    2008-11-01

    A global analysis approach to modelling doubly asymmetric, three-dimensional, multi-bay, multi-storey, wall-frame structures is presented in a form that enables the lower numbered natural frequencies to be determined approximately with the certain knowledge that none have been missed. It is assumed that the primary walls and frames of the original structure run in two orthogonal directions and that their properties may vary in a step-wise fashion at one or more storey levels. The structure therefore divides naturally into uniform segments between changes of section properties. A typical segment is then replaced by an equivalent shear-flexure-torsion coupled beam whose governing differential equations are formulated using a continuum approach and posed in the form of a dynamic member stiffness matrix. The original structure can then be re-modelled as a sophisticated stepped cantilever in the usual way. Since the mass of each segment is assumed to be uniformly distributed, it is necessary to solve a transcendental eigenvalue problem, which is accomplished using the Wittrick-Williams algorithm. A parametric study on a series of wall-frame structures of varying height with different plan configurations is given to compare the accuracy of the current approach with datum results from fully converged finite element analyses.

  10. Penetrating head injury from angle grinder: A cautionary tale

    Directory of Open Access Journals (Sweden)

    S Senthilkumaran

    2010-01-01

    Full Text Available Penetrating cranial injury is a potentially life-threatening condition. Injuries resulting from the use of angle grinders are numerous and cause high-velocity penetrating cranial injuries. We present a series of two penetrating head injuries associated with improper use of angle grinder, which resulted in shattering of disc into high velocity missiles with reference to management and prevention. One of those hit on the forehead of the operator and the other on the occipital region of the co-worker at a distance of five meters. The pathophysiological consequence of penetrating head injuries depends on the kinetic energy and trajectory of the object. In the nearby healthcare center the impacted broken disc was removed without realising the consequences and the wound was packed. As the conscious level declined in both, they were referred. CT brain revealed fracture in skull and changes in the brain in both. Expeditious removal of the penetrating foreign body and focal debridement of the scalp, skull, dura, and involved parenchyma and Watertight dural closure were carried out. The most important thing is not to remove the impacted foreign body at the site of accident. Craniectomy around the foreign body, debridement and removal of foreign body without zigzag motion are needed. Removal should be done following original direction of projectile injury. The neurological sequelae following the non missile penetrating head injuries are determined by the severity and location of initial injury as well as the rapidity of the exploration and fastidious debridement.

  11. Penetrating head injury from angle grinder: A cautionary tale.

    Science.gov (United States)

    Senthilkumaran, S; Balamurgan, N; Arthanari, K; Thirumalaikolundusubramanian, P

    2010-01-01

    Penetrating cranial injury is a potentially life-threatening condition. Injuries resulting from the use of angle grinders are numerous and cause high-velocity penetrating cranial injuries. We present a series of two penetrating head injuries associated with improper use of angle grinder, which resulted in shattering of disc into high velocity missiles with reference to management and prevention. One of those hit on the forehead of the operator and the other on the occipital region of the co-worker at a distance of five meters. The pathophysiological consequence of penetrating head injuries depends on the kinetic energy and trajectory of the object. In the nearby healthcare center the impacted broken disc was removed without realising the consequences and the wound was packed. As the conscious level declined in both, they were referred. CT brain revealed fracture in skull and changes in the brain in both. Expeditious removal of the penetrating foreign body and focal debridement of the scalp, skull, dura, and involved parenchyma and Watertight dural closure were carried out. The most important thing is not to remove the impacted foreign body at the site of accident. Craniectomy around the foreign body, debridement and removal of foreign body without zigzag motion are needed. Removal should be done following original direction of projectile injury. The neurological sequelae following the non missile penetrating head injuries are determined by the severity and location of initial injury as well as the rapidity of the exploration and fastidious debridement.

  12. Dynamic mechanical analysis of Norsorex/acrylonitrile butadiene rubber blends and their application in vibration control of steel frames

    Directory of Open Access Journals (Sweden)

    Junhong Xu

    2016-08-01

    Full Text Available The damping properties of acrylonitrile butadiene rubber/Norsorex® blends were investigated by dynamic mechanical analysis. The effects of Norsorex on the damping properties of acrylonitrile butadiene rubber/Norsorex blends were also studied. The results showed that 30-phr Norsorex could dramatically improve the damping of 70-phr acrylonitrile butadiene rubber. Compared with acrylonitrile butadiene rubber, the LA value of acrylonitrile butadiene rubber/Norsorex = 70/30 increased to 7.3 × 108 from 3.0 × 108 Pa K and the TA value increased from 26.6 to 28.4 K. To test the new high-damping-performance blends, shaking table tests on a four-story steel frame with viscoelastic damping wall were designed and the simulations were provided for verification. The experimental results indicated that the viscoelastic damping wall controlled the inter-story displacement well under apg = 7 m/s2, which exceeded the specified limit under uncontrolled conditions. The viscoelastic damping wall showed a better control effect on the displacement response than on the acceleration response subjected to El Centro ground motion for the second to fourth stories. The simulation results of SAP2000 structural analysis software showed good agreement with the experimental results. The differences between the acceleration and displacement time-history responses of the steel frame with acrylonitrile butadiene rubber and acrylonitrile butadiene rubber/Norsorex (70/30 were simulated by SAP2000.

  13. [Case report: severe neck injury caused by an angle grinder].

    Science.gov (United States)

    Corzillius, Michael; Storz, Christian; Gräsner, Jan-Thorsten

    2007-02-01

    EMS is called to a construction worker with serious cutting injuries of the neck from an angle grinder. The patient was found on the upper floor of a construction building accessible only through a scaffolding with narrow ladders. Primary examination reveals severe hemorrhagic shock. The Fire Department is called for evacuation of the patient with a turntable ladder. Further examination in the hospital shows complete dissection of the left carotid artery and the left internal jugular vein. The history reveals alcohol abuse and depression. Attempted suicide appears to be the most likely cause of the injury. The case report further discusses proper coordination of medical and technical measures in rescue operations, recommended treatment of hemorrhagic shock, and the unusual finding of paradoxical bradycardia despite volume depletion.

  14. A simple and inexpensive "cell dissociation sieve-tissue grinder" apparatus.

    Science.gov (United States)

    Pai, K; Sundar, S

    2001-05-01

    A simple and inexpensive cell dissociation sieve-tissue grinder apparatus consisting essentially of stainless steel sieve (the one popularly used for sieving tea leaves) and a glass syringe plunger acting as pestle, is described for making single cell suspension.

  15. Standard surface grinder for precision machining of thin-wall tubing

    Science.gov (United States)

    Jones, A.; Kotora, J., Jr.; Rein, J.; Smith, S. V.; Strack, D.; Stuckey, D.

    1967-01-01

    Standard surface grinder performs precision machining of thin-wall stainless steel tubing by electrical discharge grinding. A related adaptation, a traveling wire electrode fixture, is used for machining slots in thin-walled tubing.

  16. Mixed quantum/classical theory of rotationally and vibrationally inelastic scattering in space-fixed and body-fixed reference frames.

    Science.gov (United States)

    Semenov, Alexander; Babikov, Dmitri

    2013-11-07

    We formulated the mixed quantum/classical theory for rotationally and vibrationally inelastic scattering process in the diatomic molecule + atom system. Two versions of theory are presented, first in the space-fixed and second in the body-fixed reference frame. First version is easy to derive and the resultant equations of motion are transparent, but the state-to-state transition matrix is complex-valued and dense. Such calculations may be computationally demanding for heavier molecules and/or higher temperatures, when the number of accessible channels becomes large. In contrast, the second version of theory requires some tedious derivations and the final equations of motion are rather complicated (not particularly intuitive). However, the state-to-state transitions are driven by real-valued sparse matrixes of much smaller size. Thus, this formulation is the method of choice from the computational point of view, while the space-fixed formulation can serve as a test of the body-fixed equations of motion, and the code. Rigorous numerical tests were carried out for a model system to ensure that all equations, matrixes, and computer codes in both formulations are correct.

  17. Comminution of logging residues with a tub grinder: Calculation of productivity and procurement cost of wood chips

    OpenAIRE

    Yoshioka, Takuyuki; Sakurai, Rin; Aruga, Kazuhiro; Nitami, Toshio; Sakai, Hideo; Kobayashi, Hiroshi

    2006-01-01

    An experiment on comminution of logging residues with a tub grinder was carried out in order to calculate the productivity and procurement cost of wood chips. At the investigated site, the tub grinder had a hammer mill crusher at the bottom of the tub, and a grapple loader and a bucket loader worked as auxiliary machines for the grinder. As a result, the productivity of the tub grinder was 60.0 loose m3/PMH0, and the total comminuting cost was calculated as 5.637 US$/m3, indicating that th...

  18. The history of articulators: the wonderful world of "grinders," Part 2.

    Science.gov (United States)

    Starcke, Edgar N; Engelmeier, Robert L

    2012-04-01

    This is the second article in a three-part series on the history of denture grinding devices. The first article reviewed the earliest attempts to mechanically grind the occlusion of artificial teeth from the manipulation of simple articulators to very elaborate and complex machines powered by hand cranks. This article explores motor-driven grinders, most driven by way of a belt-driven pulley powered by an external source. A few were self-contained; that is, the motor was mounted on the grinder base. There were basically two types of grinders: those with cast holders for mounting processed dentures and those with provisions for using articulators for that purpose. © 2012 by the American College of Prosthodontists.

  19. ANALISA FAKTOR PENYEBAB KEGAGALAN MESIN GRINDER PADA PROSES PRODUKSI PLASTIC FILM DI PT. MUTIARA HEXAGON

    Directory of Open Access Journals (Sweden)

    Imam Hidayat

    2013-10-01

    Full Text Available Bila suatu mesin memiliki tingkat kegagalan yang tinggi, maka perlu dilakukan analisis mengenai  penyebab  –  penyebab  kegagalan  tersebut  hingga  ke  akar  permasalahannya sehingga dapat menentukan tindakan yang sesuai untuk meningkatkan kinerja suatu mesin. PT. Mutiara Hexagon merupakan sebuah perusahaan yang bergerak dibidang industri pembuatan plastik  kemasan.  Dalam  line  pembuatan lembaran film  diperlukan mesin  CPP  (Cast  Poly Propylene Machine dan mesin grinder dalam prosesnya. Pada penelitian yang dilakukan di PT. Mutiara Hexagon, terdapat beberapa kegagalan yang terjadi pada mesin grinder pada proses produksi plastic film, sehingga menyebabkan seluruh line pada divisi film mengalami downtime. Tujuan dari penelitian ini adalah untuk melakukan analisa mengenai faktor penyebab kegagalan mesin grinder, penulis melakukan observasi secara langsung dan melihat proses produksi plastic film.Penulis menggunakan metode Failure Effect and Mode Analysis (FMEA dan Fault Tree Analysis (FTA. Penerapan analisis Failure Effect and  Mode Analysis (FMEA dapat menentukan sejauh mana tingkat kegagalan terjadi. Dari hasil analisis FMEA kemudian dapat dilanjutkan dengan menggunakan Fault Tree Analysis (FTA guna mengetahui lebih lanjut penyebab-penyebab dasar suatu kegagalan.Dari hasil perhitungan nilai Risk Priority Number (RPN pada tiap-tiap kegagalan yang terjadi  diantaranya yang  paling  tinggi  adalah kegagalan mesin  grinder rusak  dengan nilai kegagalannya mencapai 120. Kemudian dianalisa penyebab kegagalan tersebut dengan menggunakan metode FTA di dapatkan minimal cut sets yaitu: as grinder patah, katup hisap blower terbuka terlalu besar, kegagalan pada motor blower, baut pada dudukan pisau patah, pisau tumpul dan human error. Berdasarkan nilai probabilitas masing-masing cut set didapatkan nilai probabilitas kegagalan grinder periode 1 Juni 2012 -1 Juni 2013 mencapai 60%.

  20. Optimizing cellulose fibrillation for the production of cellulose nanofibrils by a disk grinder

    Science.gov (United States)

    Chuanshuang Hu; Yu Zhao; Kecheng Li; J.Y. Zhu; Roland Gleisner

    2015-01-01

    The fibrillation of a bleached kraft eucalyptus pulp was investigated by means of a laboratory-scale disk grinder for the production of cellulose nanofibrils (CNF), while the parameters disk rotating speed, solid loading, and fibrillation duration were varied. The cumulative energy consumption was monitored during fibrillation. The degree of polymerization (DP) and...

  1. Dehydration of coal concentrate in a grinder with compressed air purging

    Energy Technology Data Exchange (ETDEWEB)

    Nikitin, I.N.; Murovets, N.A.; Pichugin, V.P.; Preobrazhenskiy, B.P.; Stanislavskiy, L.Ya.; Vinarskiy, M.S.; Voznyy, G.F.

    1980-01-01

    Results are presented of a dehydration study in a grinder with compressed air purging of large-size coking coal concentrate of jigging machines. A mathematical model for this method of dehydration is determined (optimal parameters, purging time, slope angle and pressure of the air stream).

  2. Stiffness analysis and comparison of a Biglide parallel grinder with alternative spatial modular parallelograms

    DEFF Research Database (Denmark)

    Wu, Guanglei; Zou, Ping

    2016-01-01

    This paper deals with the stiffness modeling, analysis and comparison of a Biglide parallel grinder with two alternative modular parallelograms. It turns out that the Cartesian stiffness matrix of the manipulator has the property that it can be decoupled into two homogeneous matrices, correspondi...

  3. Production Machine Shop Employment Competencies. Part Two: Saws, Drills, and Grinders.

    Science.gov (United States)

    Bishart, Gus; Werner, Claire

    Competencies for production machine shop are provided for the second of four topic areas: saws, drills, and grinders. Each competency appears in a one-page format. It is presented as a goal statement followed by one or more "indicator" statements, which are performance objectives describing an ability that, upon attainment, will…

  4. Universal Tool Grinder Operator Instructor's Guide. Part of Single-Tool Skills Program Machine Industries Occupations.

    Science.gov (United States)

    New York State Education Dept., Albany. Div. of Curriculum Development.

    The document is an instructor's guide for a course on universal tool grinder operation. The course is designed to train people in making complicated machine setups and precision in the grinding operations and, although intended primarily for adult learners, it can be adapted for high school use. The guide is divided into three parts: (1) the…

  5. Analisa Faktor Penyebab Kegagalan Mesin Grinder pada Proses Produksi Plastic Film di PT. Mutiara Hexagon

    OpenAIRE

    Hidayat, Imam; Pratiwi, Swandya Eka

    2013-01-01

    Bila suatu mesin memiliki tingkat kegagalan yang tinggi, maka perlu dilakukan analisis mengenai penyebab – penyebab kegagalan tersebut hingga ke akar permasalahannya sehingga dapat menentukan tindakan yang sesuai untuk meningkatkan kinerja suatu mesin. PT. Mutiara Hexagon merupakan sebuah Perusahaan yang bergerak dibidang industri pembuatan plastik kemasan. Dalam line pembuatan lembaran film diperlukan mesin CPP (Cast Poly Propylene Machine) dan mesin grinder dalam prosesnya....

  6. On-line, proximate analysis of ground beef directly at a meat grinder outlet.

    Science.gov (United States)

    Isaksson, T; Nilsen, B N; Tøgersen, G; Hammond, R P; Hildrum, K I

    1996-07-01

    The fat, moisture and protein contents of ground beef were determined on-line by a diffuse reflectance near infrared (NIR) spectroscopy instrument at the outlet of a meat grinder. Beef samples in the range of 6.2-21.7% fat, 59.6-72.9% moisture and 18.1-20.7% protein were studied. Calibrations from samples ground with hole diameters of 4, 8, 13 or 19 mm in the grinder plate were validated. In addition, calibrations of combinations of these samples from the different hole diameters were validated. Prediction errors, expressed as root mean square error of cross validation of the beef samples, were 0.73-1.50% for fat, 0.75-1.33% for moisture and 0.23-0.32% for protein, depending on the hole diameter of the grinder plate. Calibrations from samples ground with the smallest hole diameters gave lowest prediction errors. The present prediction error results are only slightly higher compared to reported prediction error results using conventional at- and off-line NIR instruments. It is concluded that the on-line NIR prediction results were acceptable for samples ground with grinder plates of 4, 8 or 13 mm hole diameter.

  7. Framing the frame

    Directory of Open Access Journals (Sweden)

    Todd McElroy

    2007-08-01

    Full Text Available We examined how the goal of a decision task influences the perceived positive, negative valence of the alternatives and thereby the likelihood and direction of framing effects. In Study 1 we manipulated the goal to increase, decrease or maintain the commodity in question and found that when the goal of the task was to increase the commodity, a framing effect consistent with those typically observed in the literature was found. When the goal was to decrease, a framing effect opposite to the typical findings was observed whereas when the goal was to maintain, no framing effect was found. When we examined the decisions of the entire population, we did not observe a framing effect. In Study 2, we provided participants with a similar decision task except in this situation the goal was ambiguous, allowing us to observe participants' self-imposed goals and how they influenced choice preferences. The findings from Study 2 demonstrated individual variability in imposed goal and provided a conceptual replication of Study 1. %need keywords

  8. The under sink garbage grinder: a friendly technology for the environment.

    Science.gov (United States)

    Bolzonella, D; Pavan, P; Battistoni, P; Cecchi, F

    2003-03-01

    The use of garbage grinders is not a usual practice in Europe, but it is in other countries around the world (e.g., North America, Japan and Australia). Sometimes, garbage grinders are accused of producing problems in sewers and wastewater treatment plants and are prohibited by environmental protection laws. In this study, the different impacts determined by the use of this technology were considered to show the positive impacts of its use. In particular, it was shown that garbage grinders enable the disposal of household organic wastes with advantages for the wastewater treatment processes because of an increase in the carbon/nutrients ratio in the wastewater. This is particularly important for biological nutrients removal processes. Daily specific contributions for person equivalent (PE) due to organic waste disposal through garbage grinders were found to be equal to 75 gCODPE(-1) d(-1) for carbon (as COD), 2.5 gNPE(-1) d(-1) for nitrogen and 0.25 gPPE(-1) d(-1) for phosphorous, respectively. Those determined a value of 30 for the COD/N ratio. Moreover, no problems with solids settling in sewers were noted. These results were extensively compared with literature data. The economical balance showed that the use of garbage grinders allowed a global saving of some 17 Euro year(-1) for a three people family. Important benefits are also gained from an environmental point of view (e.g, organic wastes disposal nutrients removal in wastewater treatment and increase in biogas production with energy reclamation).

  9. Frames and semi-frames

    OpenAIRE

    Antoine, Jean-Pierre; Balazs, Peter

    2011-01-01

    Loosely speaking, a semi-frame is a generalized frame for which one of the frame bounds is absent. More precisely, given a total sequence in a Hilbert space, we speak of an upper (resp. lower) semi-frame if only the upper (resp. lower) frame bound is valid. Equivalently, for an upper semi-frame, the frame operator is bounded, but has an unbounded inverse, whereas a lower semi-frame has an unbounded frame operator, with bounded inverse. We study mostly upper semi-frames, bot...

  10. Vibrations of rotating machinery

    CERN Document Server

    Matsushita, Osami; Kanki, Hiroshi; Kobayashi, Masao; Keogh, Patrick

    2017-01-01

    This book opens with an explanation of the vibrations of a single degree-of-freedom (dof) system for all beginners. Subsequently, vibration analysis of multi-dof systems is explained by modal analysis. Mode synthesis modeling is then introduced for system reduction, which aids understanding in a simplified manner of how complicated rotors behave. Rotor balancing techniques are offered for rigid and flexible rotors through several examples. Consideration of gyroscopic influences on the rotordynamics is then provided and vibration evaluation of a rotor-bearing system is emphasized in terms of forward and backward whirl rotor motions through eigenvalue (natural frequency and damping ratio) analysis. In addition to these rotordynamics concerning rotating shaft vibration measured in a stationary reference frame, blade vibrations are analyzed with Coriolis forces expressed in a rotating reference frame. Other phenomena that may be assessed in stationary and rotating reference frames include stability characteristic...

  11. A simple way to build a grinder for carbon-fibre electrodes for amperometry or voltammetry.

    Science.gov (United States)

    Borges, Ricardo; Díaz, Jésica; Camacho, Marcial; Machado, José D

    2005-07-01

    Carbon-fibre electrodes are used widely for studying exocytosis by amperometry. Currently, there are two major methods for insulating fibres so as to leave the tip as the only conductive surface: encapsulation with plastic or glass. The latter offers advantages such as better insulation and a known electro-active surface. In addition, such electrodes are suitable for in vivo electrochemistry because they can penetrate brain tissues. However, the construction of glass-encapsulated electrodes requires a grinder to polish the electrode surface with precision. This apparatus is expensive because it needs a very stable motor, a diamond surface and a micromanipulator. We describe the construction of a cheap precision grinder using a computer drive and an old microscope.

  12. Work-related penetrating head trauma caused by industrial grinder tool.

    Science.gov (United States)

    Abdoli, Ali; Amirjamshidi, Abbass

    2009-09-01

    Nonmissile low-velocity penetrating brain injuries are unusual among civilian population. Work-related penetrating head wounds are rarer among this group. Here, we report two rare cases of penetrating head wounds caused by industrial grinder tool. The patients (both men) were struck to the head by detached blades of the grinder tool. Depressed fractures, penetrated bone fragments, and dural lacerations were all treated by the routine fashion. Paranasal sinus damage and further cerebrospinal fluid leakage were also treated conservatively. The reported cases are unexpected variants of injuries that neurosurgeons may come across and their management is still beyond the scope of textbooks. Skill and experience of the general neurosurgeons can handle the cases properly but prevention of such incidents using safer and guarded instruments should be stressed to manufacturers.

  13. Media Framing

    DEFF Research Database (Denmark)

    Pedersen, Rasmus T.

    2017-01-01

    The concept of media framing refers to the way in which the news media organize and provide meaning to a news story by emphasizing some parts of reality and disregarding other parts. These patterns of emphasis and exclusion in news coverage create frames that can have considerable effects on news...... consumers’ perceptions and attitudes regarding the given issue or event. This entry briefly elaborates on the concept of media framing, presents key types of media frames, and introduces the research on media framing effects....

  14. Monitoring of chromium and nickel in biological fluids of grinders grinding stainless steel.

    Science.gov (United States)

    Stridsklev, Inger Cecilie; Schaller, Karl-Heinz; Langård, Sverre

    2007-04-01

    Stainless steel (SS) welders usually spend some of their working time grinding, to finish and smoothen the welding groove. The aim of this study was to investigate possible relations between the concentrations of nickel (Ni) and chromium (Cr) in the work atmosphere generated by grinders grinding SS, and to compare the air levels to the levels of Cr and Ni in their biological fluids. Hereby, it might be possible to identify the contribution of grinding to the levels of Cr and Ni in biological fluids in SS welders. Also the airborne levels of Cr and Ni in SS grinders were compared to corresponding levels in SS welders. The subjects examined in this study were selected among SS grinders not performing welding. Nine grinders were monitored for 1 workweek, measuring Cr and Ni in air, blood and urine. They were questioned about their exposure to Cr and Ni during their working careers. Air levels of total Cr up to 95 microg/m(3) and Ni levels up to 25 microg/m(3) were measured. Chromium(VI) (Cr(VI)) was detectable only in five air samples; the levels in the remaining samples were below the detection limit. The levels of Cr in blood and urine were also low. The levels of Ni in urine were close to those for MMA and MIG/MAG SS welders. In spite of high levels of total Cr and Ni observed in air, the levels found in biological fluids were low. The Cr levels in more than 50% of the whole blood and red cell samples and about 1/3 of the Cr-plasma levels were below the detection limits. The mean blood levels for Cr were 0.43, 0.60 and 0.35 microg/l, in whole blood, plasma and red cells, respectively. The mean levels for Cr in the urine was 1.6, 1.4 and 1.4 microg/g creatinine for the first void, just before and just after work. For Ni the mean blood levels were 0.87 microg/l in whole blood and 0.68 microg/l in plasma. The mean levels and ranges of Ni from the first void, just before and after work in urine were 3.79 microg/g creatinine, 3.39 and 4.56, respectively. The Cr

  15. Extension of the Vane Pump-Grinder Technology to Manufacture Finely Dispersed Meat Batters.

    Science.gov (United States)

    Irmscher, Stefan B; Gibis, Monika; Herrmann, Kurt; Oechsle, Anja Maria; Kohlus, Reinhard; Weiss, Jochen

    2016-03-01

    A vane pump-grinder system was extended to enable the manufacture of finely dispersed emulsion-type sausages by constructing and attaching a high-shear homogenizer at the outlet. We hypothesized that the dispersing capabilities of the extended system may be improved to the point of facilitating meat-fat emulsification due to an overall increased volumetric energy input EV . Coarsely ground raw material mixtures were processed to yield meat batters at varying volume flow rates (10 to 60 L/min) and rotational rotor speeds of the homogenizer nrotor (1000 to 3400 rpm). The normalized torques acting on pump, grinder, and homogenizer motors were recorded and unit power consumptions were calculated. The structure of the manufactured meat batters and sausages were analyzed via image analysis. Key physicochemical properties of unheated and heated batters, that is, texture, water-binding, color, and solubilized protein were determined. The mean diameter d10 of the visible lean meat particles varied between 352 and 406 μm whereas the mean volume-surface diameter d32 varied between 603 and 796 μm. The lightness L* ranged from 66.2 to 70.7 and correlated with the volumetric energy input and product structure. By contrast, varying process parameters did not impact color values a* (approximately 11) and b* (approximately 8). Interestingly, water-binding and protein solubilization were not affected. An exponential process-structure relationship was identified allowing manufacturers to predict product properties as a function of applied process parameters. Raw material mixtures can be continuously comminuted, emulsified, and subsequently filled into casings using an extended vane pump-grinder. © 2016 Institute of Food Technologists®

  16. Uncommon evolution of fibrosing alveolitis in a hard metal grinder exposed to cobalt dusts.

    Science.gov (United States)

    Zanelli, R; Barbic, F; Migliori, M; Michetti, G

    1994-06-30

    This study reports a case of fibrosing alveolitis with uncommon evolution in a 27-year-old male non-smoker, working as a hard metal grinder for 10 years. Personal and occupational history, routine clinical and laboratory check-up, chest X-rays, lung function tests, fiberoptic bronchoscopy with bronchoalveolar lavage and open lung biopsy returned a diagnosis of hard metal lung fibrosis. The patient felt greatly improved after removal from the workplace, without any therapy. At present, he is complaining of only mild exertional dyspnea and shows an attenuation of his ventilatory defect. The radiological picture has clearly improved and the cellular pattern of bronchoalveolar lavage was normal.

  17. ANALISA FAKTOR PENYEBAB KEGAGALAN MESIN GRINDER PADA PROSES PRODUKSI PLASTIC FILM DI PT. MUTIARA HEXAGON

    OpenAIRE

    Imam Hidayat; Swandya Eka Pratiwi

    2013-01-01

    Bila suatu mesin memiliki tingkat kegagalan yang tinggi, maka perlu dilakukan analisis mengenai  penyebab  –  penyebab  kegagalan  tersebut  hingga  ke  akar  permasalahannya sehingga dapat menentukan tindakan yang sesuai untuk meningkatkan kinerja suatu mesin. PT. Mutiara Hexagon merupakan sebuah perusahaan yang bergerak dibidang industri pembuatan plastik  kemasan.  Dalam  line  pembuatan lembaran film  diperlukan mesin  CPP  (Cast  Poly Propylene Machine) dan mesin grinder dalam prosesnya....

  18. Framing politics

    NARCIS (Netherlands)

    Lecheler, S.K.

    2010-01-01

    This dissertation supplies a number of research findings that add to a theory of news framing effects, and also to the understanding of the role media effects play in political communication. We show that researchers must think more about what actually constitutes a framing effect, and that a

  19. Framing theory

    NARCIS (Netherlands)

    de Vreese, C.H.; Lecheler, S.; Mazzoleni, G.; Barnhurst, K.G.; Ikeda, K.; Maia, R.C.M.; Wessler, H.

    2016-01-01

    Political issues can be viewed from different perspectives and they can be defined differently in the news media by emphasizing some aspects and leaving others aside. This is at the core of news framing theory. Framing originates within sociology and psychology and has become one of the most used

  20. Technological Frames

    Directory of Open Access Journals (Sweden)

    Karin Olesen

    2014-03-01

    Full Text Available The purpose of this article is to identify and explain the barriers that prevented the case study organization, an Australasian university, from implementing a groupware package. This is an insider action research case study, using qualitative semi-structured interviews, group and individual training to look at users’ technological frames around the implementation and use of a groupware product. Technological frames were used to enable a systematic examination of the assumptions, expectations, and knowledge of technology; in particular, the use of technological frames reveals aspects of user resistance. While addressing criticisms of the technological frames genre, this study uses technological frames as a lens to examine the underlying drivers and impediments to information systems (IS implementation. In this case study, changes to a groupware product failed to be implemented, not because of user resistance to the product, but because of organizational politics. This study demonstrates how the culture of an organization may stifle the implementation of IS.

  1. Comparison of tungsten carbide and stainless steel ball bearings for grinding single maize kernels in a reciprocating grinder

    Science.gov (United States)

    Reciprocating grinders can grind single maize kernels by shaking the kernel in a vial with a ball bearing. This process results in a grind quality that is not satisfactory for many experiments. Tungesten carbide ball bearings are nearly twice as dense as steel, so we compared their grinding performa...

  2. The jaw of the worm: GTPase-activating protein EAT-17 regulates grinder formation in Caenorhabditis elegans.

    Science.gov (United States)

    Straud, Sarah; Lee, Inhwan; Song, Bomi; Avery, Leon; You, Young-Jai

    2013-09-01

    Constitutive transport of cellular materials is essential for cell survival. Although multiple small GTPase Rab proteins are required for the process, few regulators of Rabs are known. Here we report that EAT-17, a novel GTPase-activating protein (GAP), regulates RAB-6.2 function in grinder formation in Caenorhabditis elegans. We identified EAT-17 as a novel RabGAP that interacts with RAB-6.2, a protein that presumably regulates vesicle trafficking between Golgi, the endoplasmic reticulum, and plasma membrane to form a functional grinder. EAT-17 has a canonical GAP domain that is critical for its function. RNA interference against 25 confirmed and/or predicted RABs in C. elegans shows that RNAi against rab-6.2 produces a phenotype identical to eat-17. A directed yeast two-hybrid screen using EAT-17 as bait and each of the 25 RAB proteins as prey identifies RAB-6.2 as the interacting partner of EAT-17, confirming that RAB-6.2 is a specific substrate of EAT-17. Additionally, deletion mutants of rab-6.2 show grinder defects identical to those of eat-17 loss-of-function mutants, and both RAB-6.2 and EAT-17 are expressed in the terminal bulb of the pharynx where the grinder is located. Collectively, these results suggest that EAT-17 is a specific GTPase-activating protein for RAB-6.2. Based on the conserved function of Rab6 in vesicular transport, we propose that EAT-17 regulates the turnover rate of RAB-6.2 activity in cargo trafficking for grinder formation.

  3. Framing truths

    OpenAIRE

    Kuester, Martin

    1992-01-01

    Framing truths : parodic structures in contemporary English-Canadian historical novels. - Toronto u.a. : Univ. of Toronto Pr., 1992. - VIII, 192 S. - Zugl.: Winnipeg, Univ. of Manitoba, Diss., 1990. - (Theory/culture ; 12)

  4. Optimization of ultrasonic cell grinder extraction of anthocyanins from blueberry using response surface methodology.

    Science.gov (United States)

    Jiang, Hai-Long; Yang, Jun-Li; Shi, Yan-Ping

    2017-01-01

    Ultrasonic cell grinder extraction (UCGE), using water as the solvent, was firstly applied to extract anthocyanins from blueberry. Extraction yield was related with four variables, including ratio of solution to solid, extraction power, buffer time, and extraction time. On the basis of response surface methodology (RSM), the optimal conditions were determined to be the ratio of solution to solid as 25:1(mL/g), the extraction power as 1500W, the buffer time as 3.0s, and the extraction time as 40min. The experimental yield of anthocyanins using UCGE was 2.89mg/g higher than that of conventional ultrasound-assisted extraction (CUAE). This study indicated that UCGE was an innovative, efficient, and environment friendly method in ultrasonic extraction fields, and had a potential to effectively extract other bioactive constituents. Copyright © 2016 Elsevier B.V. All rights reserved.

  5. Performance of Disk Mill Type Mechanical Grinder for Size Reducing Process of Robusta Roasted Beans

    Directory of Open Access Journals (Sweden)

    Sri Mulato

    2006-12-01

    Full Text Available One of improtant steps in secondary coffee processing that influence on final product quality such as consistency and uniformity is milling process. Usually, Indonesian smallholder used "lumpang" for milling coffee roasted beans to coffee powder product which caused the final product not uniformed and consistent, and low productivity. Milling process of coffee roasted beans can be done by disk mill type mechanical grinder which is used by smallholder for milling several cereals. Indonesian Coffee and Cocoa Research Institute have developed disk mill type grinding machine for milling coffee roasted beans. Objective of this research is to find performance of disk mill type grinding machine for size reducing process of Robusta roasted beans from several size dried beans and roasting level treatments. Robusta dried beans which are taken from dry processing method have 13—14% moisture content (wet basis, 680—685 kg/m3 density, and classified in 3 sizes level. The result showed that the disk mill type of grinding machine could be used for milling Robusta roasted beans. Machine hascapacity 31—54 kg/h on 5,310—5,610 rpm axle rotation and depend on roasting level. Other technical parameters were 91—98% process efficientcy, 19—31 ml/ kg fuel consumption, 0.3—1% slips, 50—55% particles had diameter less than 230 mesh and 38—44% particles had diameter bigger than 100 mesh, 32—38% lightness was increased, 0.6—12.6% density was decreased, and solubility of coffee powder between 28—30%. Cost milling process per kilogram of Robusta roasted beans which light roast on capacity 30 kg/hour was Rp362.9. Key words : Coffee roasted, Robusta, disk mill, mechanical grinder, size reduction.

  6. Distribution patterns of Escherichia coli O157:H7 in ground beef produced by a laboratory-scale grinder.

    Science.gov (United States)

    Flores, Rolando A; Tamplin, Mark L

    2002-12-01

    This study determined the distribution patterns of Escherichia coli O157:1H7 in ground beef when a contaminated beef trim was introduced into a batch of uncontaminated beef trims prior to grinding in a small-scale laboratory grinder. A beef trim (15.3 +/- 2 g) was inoculated with a rifampicin-resistant strain of E. coli O157:H7 (E. coli O157:H7rif) and introduced into a stream of noncontaminated beef (322 +/- 33 g) prior to grinding. Seven inoculum levels (6, 5, and 4 total log CFU [high]; and 3, 2, 1, and 0 total log CFU [low]) were studied in triplicate. E. coli O157:H7rif was not detected in 3.1 to 43% of the ground beef inoculated with the high levels or in 3.4 to 96.9% of the ground beef inoculated with the low levels. For all inoculum levels studied, the five ground beef fractions (each 7.8 +/- 0.6 g) with the highest pathogen levels accounted for 59 to 100% of the total pathogens detected. For all inoculum levels, there was a linear relationship between the quantity of ground beef containing E. coli O157:H7rif and the inoculum level. The quantity of E. coli O157:H7rif in the beef remaining in the grinder was proportional to the inoculum level and was related to the location in the grinder. Different components of the grinder accumulated E. coli O157:H7rif in different quantities, with the most significant accumulation being in the nut (collar) that attaches the die to the blade. This study determined specific distribution patterns of E. coli O157:H7rif after the grinding of a contaminated beef trim along with uncontaminated trims, and the results indicate that the grinding operation should be regarded as a means of distribution of microbial contamination in risk analyses of ground beef operations.

  7. Framing scales and scaling frames

    NARCIS (Netherlands)

    Lieshout, van M.; Dewulf, A.; Aarts, M.N.C.; Termeer, C.J.A.M.

    2009-01-01

    Policy problems are not just out there. Actors highlight different aspects of a situation as problematic and situate the problem on different scales. In this study we will analyse the way actors apply scales in their talk (or texts) to frame the complex decision-making process of the establishment

  8. Framing Feminism

    OpenAIRE

    Mendes, Kaitlynn

    2011-01-01

    This article analyses the framing in four British and American newspapers of the second wave feminist movement during its most politically active period (1968–1982). Using content and critical discourse analysis of 555 news articles, the article investigates how movement members were represented, what problems and solutions to women’s oppression/inequality were posed and whose voices were used. This paper identifies: opposition to the movement, support for the movement, conflict and movement ...

  9. Upper limb aerobic training improves aerobic fitness and all-out performance of America's Cup grinders.

    Science.gov (United States)

    Adami, Paolo Emilio; Delussu, Anna Sofia; Rodio, Angelo; Squeo, Maria Rosaria; Corsi, Loretta; Quattrini, Filippo Maria; Fattorini, Luigi; Bernardi, Marco

    2015-01-01

    This research on "America's Cup" grinders investigated the effects of a specific eight-week long-arm cranking ergometer (ACE) training on upper body (UB) aerobic fitness (ventilatory threshold - Tvent, respiratory compensation point- RCP, -oxygen uptake peak - VO₂peak) and high intensity working capacity. The training consisted of sessions carried out for 20-30 mins, three times per week, at an intensity between the UB-Tvent and UB-RCP, and replaced part of a typical lower limb aerobic training whilst maintaining the usual weekly schedule of callisthenics, resistance training and sailing. Seven sailors, including four grinders and three mastmen (age 30 ± 5.5 years, height 1.9 ± 0.04 m, body mass 102 ± 3.6 kg), were evaluated through both an ACE cardiopulmonary maximal exercise test (CPET) and an ACE all-out up to exhaustion exercise test, before and after the ACE training. UB aerobic fitness improved significantly: UB-VO₂peak increased from 4.29 ± 0.442 to 4.52 ± 0.522 l·min(-1) (6.4 ± 3.66%), VO₂ at UB-Tvent from 2.42 ± 0.282 to 2.97 ± 0.328 l·min(-1) (22.8 ± 5.09%) and VO₂ at UB-RCP from 3.25 ± 0.402 to 3.75 ± 0.352 l·min(-1) (16.1 ± 10.83%). Peak power at the ACE CPET increased from 351 ± 27.5 to 387 ± 33.5 W (10.5 ± 6.93%). The all-out test total mechanical work increased from 28.9 ± 2.35 to 40.1 ± 3.76 kJ (72.1 ± 4.67%). In conclusion, a high intensity aerobic ACE training can be effective in improving grinding performance by increasing UB aerobic fitness and all-out working capacity.

  10. [A case of hard metal lung disease in a man who worked as an iron grinder].

    Science.gov (United States)

    Sakai, Maki; Kato, Go; Fujioka, Takeshi; Sugihara, Makoto; Koyanagi, Koutaro; Kato, Osamu; Tominaga, Masaki; Kawabata, Yoshinori

    2010-04-01

    The patient was a man who had suffered from repeated pneumothoraces since August 2003, when he was 16 years old. A right pneumothorax was observed at age 21 years, in April 2008. At the same time, a dry cough began to appear and diffuse small nodular shadows in both lung fields were found on a chest X-ray film. Due to worsening symptoms and the chest X-ray findings, a transbronchial lung biopsy was performed in September 2008. Pathological examination showed mural type organization, and large numbers of multinucleated giant cells that were engulfing nucleated cells and had black pigment in their cytoplasm. Giant cell interstitial pneumonia and hard metal lung disease (HMLD) were suspected because of the patient's occupational history as a metal grinder, which included the use of a hard metal tool for three years since August 2005. In an elementary analysis using an electron probe microanalyzer, tungsten was detected in resected lung tissue obtained in April 2008 which confirmed the diagnosis. His symptoms improved after the initiation of corticosteroid therapy, which continued but with a gradual decrease in the dose. In this case, HMLD developed over a relatively short period despite the low level of dust dispersal of a hard-metal tool, perhaps because of a hypersensitivity of the patient to hard metal.

  11. Extraction and Characterization of Nanocellulose Structures from Linter Dissolving Pulp Using Ultrafine Grinder.

    Science.gov (United States)

    Ghasemi, Somayeh; Behrooz, Rabi; Ghasemi, Ismail

    2016-06-01

    The objective of this study was to extract cellulose nanofibrils (CNFs) from Linter dissolving pulp through a simple and environmentally friendly physical method of refining pretreatment coupled with ultrafine grinder. The morphology, structure and properties of the Linter pulp and obtained NFCs were investigated using Optical Microscopy (OM), electron microscopy (SEM), Atomic Force Microscopy (AFM), Fourier transformed infrared (FTIR) spectra, X-ray diffraction (XRD) and Thermogravimetric (TG) analysis. The OM results indicate that, the Linter Pulp had length and wide mainly ranged 1.3 mm and 13 μm respectively. Based on AFM images, most of extracted nanocellulose had spherical shape and the average of nanocellulose diameter was varied between 30-70 nm when measured by AFM and SEM. Also the FTIR spectra confirmed that the basic structure of nanocellulose was maintained and no derivative was formed. The X-ray results show that by this method of extraction, the crystallinity index of Nanocellulose isolated (62%) decreased in compared to Linter Pulp (79.5%). Also Linter pulp decomposes at higher temperature (280 degrees C) than isolated nanocellulose (240 degrees C).

  12. Accelerated silicosis with mixed-dust pneumoconiosis in a hard-metal grinder.

    Science.gov (United States)

    Cohen, C; Fireman, E; Ganor, E; Man, A; Ribak, J; Lerman, Y

    1999-06-01

    We describe a fatal case of accelerated silicosis with a component of mixed-dust pneumoconiosis in a young hard-metal grinder that we believe is the first case of its kind in Israel and one of the rare cases reported worldwide. The patient's diagnosis was based on typical features: restrictive lung function, abnormal chest roentgenogram suggesting lung fibrosis, a history of exposure to silica and hard metals, bronchoalveolar lavage (BAL) fluid findings, and mineralogical studies. BAL cells showed an abundance of giant multinucleated macrophages. The CD4/CD8 ratio of T lymphocytes was 1.1, with a high percentage of CD8 and CD8/38 positive cells (37% suppressor/cytotoxic and 12% cytotoxic T lymphocytes, respectively). mRNA transcripts isolated from BAL cells were positive for interleukin-1 (IL-1) and transforming growth factor (TGF) Il-5, IL-2, and IL-10 but not for IL-6, IL-4, and interferon. Polarizing light microscopic studies of BAL and induced sputum cells showed polarizing particles, which are typical for silica. Mineralogical studies of electron microscopy performed on BAL fluid and on dust collected at the patient's workstation revealed silica particles as well as aluminum-titanium and other particles. The latter might have contributed to the patient's lung disease.

  13. A new "Perforator Grinder-Aspirator Apparatus (PGAA)" for the minimal access surgery of cystic liver hydatidosis.

    Science.gov (United States)

    Avtan, L

    2005-01-01

    Despite that minimal access surgery is a feasible, effective and viable option for radical surgical treatment of cystic hydatidosis, the laparoscopic approach is not widely accepted because of the risk of recurrence and the risk of severe complications, such as anaphylaxis and/or contamination of the peritoneal cavity related with the spillage. To overcome these difficulties, several techniques and devices are described in the literature. In our center (ISTEM), we have designed and developed a new generation "Perforator-Grinder-Aspirator Apparatus (PGAA: patent no. TR-2004/02916)" which evacuates cyst contents in a more secure, effective and easy way. By using PGAA, we are able to perform the laparoscopic approach while keeping the necessary pneumoperitoneum pressure to evacuate the cyst contents of liver hydatidosis securely and effectively, with wider indications even in difficult locations, after testing its safety and efficacy in some ex-vivo animal livers with hydatid cysts. PGAA is made up of four main units including puncture-irrigation needle, perforator-grinder pipe, aspiration cannula and, electric motor. One of the most important specialties of this new PGAA is having the automatically retractable rotary blade on the distal edge to grind and evacuate all the contents of the cavity including germinal layer and scolices. Having the retractable rotary blade allows the operator to avoid any intracystic parenchymal damage after perforating the outer layer. After taking out the perforator-grinder pipe, the aspiration cannula allows the laparoscopic visualization of the inner surface of the cystic cavity through its 10-mm internal diameter. In this article, the author describes the technical aspect and specifications of PGAA, and its applications in some cases with awkwardly located liver hydatid cysts, underlying its superiority over the classical aspirators and other devices.

  14. Removal of metal penile foreign body with a widely available emergency-medical-services-provided air-driven grinder.

    Science.gov (United States)

    Santucci, Richard A; Deng, Donna; Carney, Jeff

    2004-06-01

    Penile incarceration with heavy metal objects can be a difficult problem, especially if the object cannot be removed by the standard equipment available in the hospital (eg, ring cutters, bolt cutters, motorized rotary tool). We report removal of heavy iron (barbell) and steel (sledgehammer head) items incarcerating the penis with a heavy-duty air grinder provided by the fire department. This is the first such report of which we are aware. Features of safe removal of these items are reviewed, including cooling the metal item with ice to prevent tissue heating, protecting the patient from sparks, and protecting the penis from the cutting blade.

  15. A Comparasion in Graft Resorption between Three Techniques of Diced Cartilage Using Surgical Blade, Electrical Grinder and Grater in Rabbit.

    Science.gov (United States)

    Manafi, Ali; Sabet, Mohammad; Emami, Abolhasan; Vasei, Mohammad; Mosavi, Jaber; Manafi, Amir; Hamedi, Zahra Sadat; Manafi, Farzad; Mehrabani, Golnoush; Manafi, Navid

    2014-01-01

    In recent years, there is an increasing tendency to use diced cartilage grafts in rhinoplasty surgery for improving dorsum contour irregularities. This study was designed to compare graft resorption between three techniques of diced cartilage using surgical blade, electrical grinder and grater in rabbit model. Thirteen New Zealand rabbits were divided into three groups. Three 2×2 cm cartilage specimens were harvested from one of their ears. In group one, the cartilage was diced by use of No:11 surgical blade to o.5 to 1 mm cube pieces. In group two, an electrical grinder was used and in group three, a grater was applied. The grafts were placed in three subcutaneous pockets in the back of rabbits and after 12 weeks, the implants were removed and their weight and volume were recorded and were evaluated by histological techniques. There was no difference between the three methods in the 3 groups for graft resorption. There was no change in the volume, but the weight showed a decrease in the control group. As the histological results had no statistically difference between groups, we may recommend use of these two techniques in reconstructive and in aesthetic cases.

  16. Ultrasonic cell grinder extraction of anthraquinones from radix et rhizoma Rhei and determination by ultra-performance liquid chromatography.

    Science.gov (United States)

    Wang, Guo-Ying; Qi, Huan-Yang; Shi, Yan-Ping

    2010-06-01

    An ultrasonic cell grinder extraction (UCGE) method has been developed and applied to extract five anthraquinones (physcion, chrysophanol, emodin, rhein, and aloe-emodin) from radix et rhizoma Rhei. Several parameters of UCGE procedure, including ultrasonic cell grinder running mode, type and volume of extraction solvent and extraction time, were optimized. The determination was preformed on a Waters ultra-performance LC BEH C(18) column using gradient elution system. A baseline separation could be achieved in less than 7.5 min with high resolution. Under the optimized conditions, contents of physcion, chrysophanol, emodin, rhein and aloe-emodin in radix et rhizoma Rhei collected from different cultivated areas were 0-4.22, 0.11-27.64, 0.09-3.49, 0.31-3.31 and 0.13-2.93 mg/g, respectively. Compared with reflux, maceration and ultrasonic bath extractions, the UCGE method was more efficient, faster and easier to be operated, and required lower extraction temperature and less solvent. The results indicated that UCGE was a novel and ideal method for extracting bioactive constituents from plant samples.

  17. A Comparasion in Graft Resorption between Three Techniques of Diced Cartilage Using Surgical Blade, Electrical Grinder and Grater in Rabbit

    Science.gov (United States)

    Manafi, Ali; Sabet, Mohammad; Emami, Abolhasan; Vasei, Mohammad; Mosavi, Jaber; Manafi, Amir; Hamedi, Zahra Sadat; Manafi, Farzad; Mehrabani, Golnoush; Manafi, Navid

    2014-01-01

    BACKGROUND In recent years, there is an increasing tendency to use diced cartilage grafts in rhinoplasty surgery for improving dorsum contour irregularities. This study was designed to compare graft resorption between three techniques of diced cartilage using surgical blade, electrical grinder and grater in rabbit model. METHODS Thirteen New Zealand rabbits were divided into three groups. Three 2×2 cm cartilage specimens were harvested from one of their ears. In group one, the cartilage was diced by use of No:11 surgical blade to o.5 to 1 mm cube pieces. In group two, an electrical grinder was used and in group three, a grater was applied. The grafts were placed in three subcutaneous pockets in the back of rabbits and after 12 weeks, the implants were removed and their weight and volume were recorded and were evaluated by histological techniques. RESULTS There was no difference between the three methods in the 3 groups for graft resorption. There was no change in the volume, but the weight showed a decrease in the control group. CONCLUSIONS As the histological results had no statistically difference between groups, we may recommend use of these two techniques in reconstructive and in aesthetic cases. PMID:25489525

  18. On frame multiresolution analysis

    DEFF Research Database (Denmark)

    Christensen, Ole

    2003-01-01

    We use the freedom in frame multiresolution analysis to construct tight wavelet frames (even in the case where the refinable function does not generate a tight frame). In cases where a frame multiresolution does not lead to a construction of a wavelet frame we show how one can nevertheless...

  19. Simple, inexpensive, and precise paraffin tissue microarrays constructed with a conventional microcompound table and a drill grinder.

    Science.gov (United States)

    Vogel, Ulrich F; Bueltmann, Burkhard D

    2006-09-01

    In 1998, paraffin tissue microarrays (PTMAs) as paraffin blocks containing up to 1,000 cylindrical paraffin tissue core biopsy specimens (PTCBs) for high-throughput molecular profiling of tumor specimens were introduced. PTCBs can be constructed using a manual tissue puncher/arrayer (Beecher Instruments, Sun Prairie, WI; cost, at least $7,000). Furthermore, custom-built PTMAs such as the MaxArray are created by companies such as Zymed Laboratories (South San Francisco, CA; PTMA with 96 holes, about $900). In our search for a less expensive alternative, we constructed PTMAs with up to 558 PTCBs by using a drill grinder, a drill stand, and a microcompound table (Proxxon, Niersdorf, Germany; cost, <$300).

  20. Monitoring vibrations

    Energy Technology Data Exchange (ETDEWEB)

    Tiryaki, B. [Hacettepe University (Turkey). Dept. of Mining Engineering

    2003-12-01

    The paper examines the prediction and optimisation of machine vibrations in longwall shearers. Underground studies were carried out at the Middle Anatolian Lignite Mine, between 1993 and 1997. Several shearer drums with different pick lacing arrangements were designed and tested on double-ended ranging longwall shearers employed at the mine. A computer program called the Vibration Analysis Program (VAP) was developed for analysing machine vibrations in longwall shearers. Shearer drums that were tested underground, as well as some provided by leading manufacturers, were analyzed using these programs. The results of the experiments and computer analyses are given in the article. 4 refs., 9 figs.

  1. Prime tight frames

    DEFF Research Database (Denmark)

    Lemvig, Jakob; Miller, Christopher; Okoudjou, Kasso A.

    2014-01-01

    We introduce a class of finite tight frames called prime tight frames and prove some of their elementary properties. In particular, we show that any finite tight frame can be written as a union of prime tight frames. We then characterize all prime harmonic tight frames and use thischaracterization...... to suggest effective analysis and synthesis computation strategies for such frames. Finally, we describe all prime frames constructed from the spectral tetris method, and, as a byproduct, we obtain a characterization of when the spectral tetris construction works for redundancies below two....

  2. Framing the Realist Novel

    OpenAIRE

    Blunden, Ralph

    2017-01-01

    Framing the Realist novel develops a theory of framing the realist novel with a distinction made between internal framing devices and the external frames of ontology and ethics. An encompassing methodological frame of critical rationality is developed. What the realist novel is is discussed in chapter one and a distinction is drawn between the historical period in the second half of the nineteenth century and realism that pervades realist narrative more generally. Chapter three applies the th...

  3. Stroboscopic shearography for vibration analysis

    Science.gov (United States)

    Steinchen, Wolfgang; Kupfer, Gerhard; Maeckel, Peter; Voessing, Frank

    1999-09-01

    Digital Shearography, a laser interferometric technique in conjunction with the digital image processing, has the potential for vibration analysis due to its simple optical system and insensitivity against small rigid body motions. This paper will focus on its recent developments for vibration analysis and for nondestructive testing (NDT) by dynamic (harmonical) excitation. With the introduction of real time observation using automatically refreshing reference frame, both small and large rigid body motions are greatly suppressed. The development of a smaller and more mobile measuring device in conjunction with a user guided comfortable program Shearwin enables the digital shearography to be applied easily as an industrial online testing tool.

  4. Vibrational Diver

    Science.gov (United States)

    Kozlov, Victor; Ivanova, Alevtina; Schipitsyn, Vitalii; Stambouli, Moncef

    2014-10-01

    The paper is concerned with dynamics of light solid in cavity with liquid subjected to rotational vibration in the external force field. New vibrational phenomenon - diving of a light cylinder to the cavity bottom is found. The experimental investigation of a horizontal annulus with a partition has shown that under vibration a light body situated in the upper part of the layer is displaced in a threshold manner some distance away from the boundary. In this case the body executes symmetric tangential oscillations. An increase of the vibration intensity leads to a tangential displacement of the body near the external boundary. This displacement is caused by the tangential component of the vibrational lift force, which appears as soon as the oscillations lose symmetry. In this case the trajectory of the body oscillatory motion has the form of a loop. The tangential lift force makes stable the position of the body on the inclined section of the layer and even in its lower part. A theoretical interpretation has been proposed, which explains stabilization of a quasi-equilibrium state of a light body near the cavity bottom in the framework of vibrational hydromechanics.

  5. Acute effects of shock-type vibration transmitted to the hand-arm system.

    Science.gov (United States)

    Schäfer, N; Dupuis, H; Hartung, E

    1984-01-01

    The aim of the project was to find out whether shock-type vibration of hand-tools compared to non-impulsive vibration has stronger acute effects on the hand-arm system and therefore needs a stricter evaluation from the occupational health point of view in comparison with the requirements of the Draft International Standard ISO-DIS 5349. Under laboratory conditions, subjects were exposed to simulated vibration of hand-tools (grinder, chain saw, hammer-drill, pneumatic hammer, rivet hammer and nailer). The following evaluation criteria were used: biomechanical transmissibility of the hand-arm system (wrist, elbow joint, shoulder joint); muscle-activity (m. flexor carpi ulnaris, m. biceps, m. triceps); peripheral circulation (skin temperature) and subjective perception (comparison of intensity of standard and test vibrations). The results show no significant difference in acute effects on the hand-arm system between impulsive and non-impulsive type vibrations of the hand-tools tested with respect to the chosen vibration level, short-time exposure (up to 8 min) and evaluation criteria. In summary, therefore, it may be concluded that for the evaluation of shock-type vibration of the hand-tools tested, it is justified to use the existing Draft International Standard ISO-DIS 5349.

  6. Frame Permutation Quantization

    OpenAIRE

    Nguyen, Ha Q.; Goyal, Vivek K; Lav R Varshney

    2009-01-01

    Frame permutation quantization (FPQ) is a new vector quantization technique using finite frames. In FPQ, a vector is encoded using a permutation source code to quantize its frame expansion. This means that the encoding is a partial ordering of the frame expansion coefficients. Compared to ordinary permutation source coding, FPQ produces a greater number of possible quantization rates and a higher maximum rate. Various representations for the partitions induced by FPQ are presented, and recons...

  7. Deep Frame Interpolation

    OpenAIRE

    Samsonov, Vladislav

    2017-01-01

    This work presents a supervised learning based approach to the computer vision problem of frame interpolation. The presented technique could also be used in the cartoon animations since drawing each individual frame consumes a noticeable amount of time. The most existing solutions to this problem use unsupervised methods and focus only on real life videos with already high frame rate. However, the experiments show that such methods do not work as well when the frame rate becomes low and objec...

  8. Filter Bank Fusion Frames

    OpenAIRE

    Chebira, Amina; Fickus, Matthew; Mixon, Dustin G.

    2010-01-01

    In this paper we characterize and construct novel oversampled filter banks implementing fusion frames. A fusion frame is a sequence of orthogonal projection operators whose sum can be inverted in a numerically stable way. When properly designed, fusion frames can provide redundant encodings of signals which are optimally robust against certain types of noise and erasures. However, up to this point, few implementable constructions of such frames were known; we show how to construct them using ...

  9. Making students' frames explicit

    DEFF Research Database (Denmark)

    Nielsen, Louise Møller; Hansen, Poul Henrik Kyvsgaard

    2016-01-01

    Framing is a vital part of the design and innovation process. Frames are cognitive shortcuts (i.e. metaphors) that enable designers to connect insights about i.e. market opportunities and users needs with a set of solution principles and to test if this connection makes sense. Until now, framing...

  10. Frame-to-frame coherent GPU splatting

    OpenAIRE

    Grau Carrion, Sergi; Tost Pardell, Daniela

    2008-01-01

    Recently, several improvements of the classical splatting volume rendering technique have been proposed, specifically, GPU implementations that considerably speed it up. However, splatting time-varying data, even using the GPU, is still slow and not very suitable for interactive data exploration through time. In this paper, we propose a GPU-based viewaligned splatting algorithm that exploits frame-to-frame coherence to render time-varying volume datasets. Our method run-length enc...

  11. The Hermeneutics of Frames and Framing

    OpenAIRE

    Michael J. Carter

    2013-01-01

    Frames are organizing principles that are socially shared and persistent over time, and that work symbolically to meaningfully structure the social world. The study of framing has grown over the past decades as mass media has become more and more ubiquitous in society. People rely on media for information and access to local, national, and world events. This reliance on the media is important to address as news stories...

  12. Vibrating minds

    CERN Document Server

    2009-01-01

    Ed Witten is one of the leading scientists in the field of string theory, the theory that describes elementary particles as vibrating strings. This week he leaves CERN after having spent a few months here on sabbatical. His wish is that the LHC will unveil supersymmetry.

  13. Multivariate wavelet frames

    CERN Document Server

    Skopina, Maria; Protasov, Vladimir

    2016-01-01

    This book presents a systematic study of multivariate wavelet frames with matrix dilation, in particular, orthogonal and bi-orthogonal bases, which are a special case of frames. Further, it provides algorithmic methods for the construction of dual and tight wavelet frames with a desirable approximation order, namely compactly supported wavelet frames, which are commonly required by engineers. It particularly focuses on methods of constructing them. Wavelet bases and frames are actively used in numerous applications such as audio and graphic signal processing, compression and transmission of information. They are especially useful in image recovery from incomplete observed data due to the redundancy of frame systems. The construction of multivariate wavelet frames, especially bases, with desirable properties remains a challenging problem as although a general scheme of construction is well known, its practical implementation in the multidimensional setting is difficult. Another important feature of wavelet is ...

  14. [Giant cell interstitial pneumonia in a metal grinder with an abnormally high level of serum CA19-9].

    Science.gov (United States)

    Seike, M; Usuki, J; Uematsu, K; Enomoto, T; Shinoda, K; Yoshimori, K; Fukuda, Y; Kudoh, S; Niitani, H

    1995-08-01

    Interstitial pneumonia and recurrent pneumothorax developed in a 48-year-old man who had worked as a metal grinder. He died of respiratory failure despite having received antibiotics and steroids, and despite having undergone pleural sclerosis therapy. Giant cell interstitial pneumonia was diagnosed; innumerable bizarre giant cells engulfing black granules were found within the alveoli. The results of high-energy dispersion X-ray microanalysis indicated that the patient had hard metal pneumoconiosis associated with tungsten in the black granules. When he was admitted to the hospital, his serum CA19-9 and SLEX concentrations were abnormally high (2600 and 200 ng/ml, respectively). Immunohistochemical analysis of lung tissue was done with anti-CA19-9 and SLEX antibodies. CA19-9 staining revealed strong bronchialization and squamous metaplasia in contrast to type II hyperplasia. SLEX staining showed strong type II hyperplasia. Further investigations will be needed to determine the mechanism of elevated tumor-associated carbohydrate antigens in serum.

  15. A Frame Size Adjustment with Sub-Frame Observation for Dynamic Framed Slotted Aloha

    OpenAIRE

    Robithoh Annur; Suvit Nakpeerayuth

    2016-01-01

    In this paper, a simple frame size adjustment of dynamic framed slotted Aloha for tag identification in RFID networks is proposed. In dynamic framed slotted Aloha, the reader is required to announce the frame size for every frame. To achieve maximum system efficiency, it is essential to set the frame size according to the number unidentified tags appropriately. The proposed approach utilizes the information from a portion of the frame to adjust the size of the next frame. Simulation results s...

  16. Multimodal news framing effects

    NARCIS (Netherlands)

    Powell, T.E.

    2017-01-01

    Visuals in news media play a vital role in framing citizens’ political preferences. Yet, compared to the written word, visual images are undervalued in political communication research. Using framing theory, this thesis redresses the balance by studying the combined, or multimodal, effects of visual

  17. Timber frame walls

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan de Place; Brandt, Erik

    2010-01-01

    A ventilated cavity is usually considered good practice for removing moisture behind the cladding of timber framed walls. Timber frame walls with no cavity are a logical alternative as they are slimmer and less expensive to produce and besides the risk of a two-sided fire behind the cladding...

  18. Discretization of continuous frame

    Indian Academy of Sciences (India)

    which is a positive, self-adjoint, invertible operator on H with A · IdH ≤ SWω ≤ B · IdH. 2. Main result. For establishing a relationship between discrete and continuous frame of subspaces, we generalize the concept of continuous frame and resolution of identity to arbitrary Hilbert space H. For this purpose, we introduce the ...

  19. Nullspaces and frames

    OpenAIRE

    Antezana, J.; Corach, G.; Ruiz, M.; Stojanoff, D.

    2005-01-01

    In this paper we give new characterizations of Riesz and conditional Riesz frames in terms of the properties of the nullspace of their synthesis operators. On the other hand, we also study the oblique dual frames whose coefficients in the reconstruction formula minimize different weighted norms.

  20. Modern Steel Framed Schools.

    Science.gov (United States)

    American Inst. of Steel Construction, Inc., New York, NY.

    In view of the cost of structural framing for school buildings, ten steel-framed schools are examined to review the economical advantages of steel for school construction. These schools do not resemble each other in size, shape, arrangement or unit cost; some are original in concept and architecture, and others are conservative. Cost and…

  1. Dragging of inertial frames.

    Science.gov (United States)

    Ciufolini, Ignazio

    2007-09-06

    The origin of inertia has intrigued scientists and philosophers for centuries. Inertial frames of reference permeate our daily life. The inertial and centrifugal forces, such as the pull and push that we feel when our vehicle accelerates, brakes and turns, arise because of changes in velocity relative to uniformly moving inertial frames. A classical interpretation ascribed these forces to acceleration relative to some absolute frame independent of the cosmological matter, whereas an opposite view related them to acceleration relative to all the masses and 'fixed stars' in the Universe. An echo and partial realization of the latter idea can be found in Einstein's general theory of relativity, which predicts that a spinning mass will 'drag' inertial frames along with it. Here I review the recent measurements of frame dragging using satellites orbiting Earth.

  2. Urban vibrations

    DEFF Research Database (Denmark)

    Morrison, Ann; Knudsen, L.; Andersen, Hans Jørgen

    2012-01-01

      lab   studies   in   that   we   found   a   decreased   detection   rate   in   busy   environments.   Here   we   test   with   a   much   larger   sample   and   age   range,   and   contribute   with   the   first   vibration  sensitivity  testing  outside  the  lab  in  an  urban   public...

  3. Framing Gangnam Style

    Directory of Open Access Journals (Sweden)

    Hyunsun Catherine Yoon

    2017-08-01

    Full Text Available This paper examines the way in which news about Gangnam Style was framed in the Korean press. First released on 15th July 2012, it became the first video to pass two billion views on YouTube. 400 news articles between July 2012 and March 2013 from two South Korean newspapers - Chosun Ilbo and Hankyoreh were analyzed using the frame analysis method in five categories: industry/economy, globalization, cultural interest, criticism, and competition. The right-left opinion cleavage is important because news frames interact with official discourses, audience frames and prior knowledge which consequently mediate effects on public opinion, policy debates, social movement and individual interpretations. Whilst the existing literature on Gangnam Style took rather holistic approach, this study aimed to fill the lacuna, considering this phenomenon as a dynamic process, by segmenting different stages - recognition, spread, peak and continuation. Both newspapers acknowledged Gangnam Style was an epochal event but their perspectives and news frames were different; globalization frame was most frequently used in Chosun Ilbo whereas cultural interest frame was most often used in Hankyoreh. Although more critical approaches were found in Hankyoreh, reflecting the right-left opinion cleavage, both papers lacked in critical appraisal and analysis of Gangnam Style’s reception in a broader context of the new Korean Wave.

  4. New characterizations of fusion frames (frames of subspaces)

    Indian Academy of Sciences (India)

    bounded surjective operator. Keywords. Frame; fusion frame (frames of subspaces); exact fusion frame; Bessel fusion sequence; orthonormal fusion basis; pseudo-inverses. 1. Introduction. A frame is a redundant set of vectors in a Hilbert space H with the property that provide usually non-unique representations of vectors in ...

  5. Framed primal elements

    OpenAIRE

    Debongnie, Jean-François

    1986-01-01

    Framed primal finite elements may be viewed as a generalized class of elements including conforming elements, primal hybrids, and non concorming elements passing the patch test. This systematization is illustrated on a lot of examples.

  6. Framing (implicitly) matters

    DEFF Research Database (Denmark)

    Anderson, Joel; Antalikova, Radka

    2014-01-01

    and implicit attitudes of Christian and Atheist Danes toward targets framed as Muslims or as immigrants. The results showed that explicit and implicit attitudes were more negative when the target was framed as a Muslim, rather than as an immigrant. Interestingly, implicit attitudes were qualified...... by the participants’ religion. Specifically, analyses revealed that Christians demonstrated more negative implicit attitudes toward immigrants than Muslims. Conversely, Atheists demonstrated more negative implicit attitudes toward Muslims than Atheists. These results suggest a complex relationship between religion...

  7. Multimodal news framing effects

    OpenAIRE

    Powell, T.E.

    2017-01-01

    Visuals in news media play a vital role in framing citizens’ political preferences. Yet, compared to the written word, visual images are undervalued in political communication research. Using framing theory, this thesis redresses the balance by studying the combined, or multimodal, effects of visual and verbal media. Three experimental studies using international affairs news – a ready source of compelling visuals – address the following questions: (a) what is the individual and combined cont...

  8. Framing French Culture

    OpenAIRE

    Edwards, Natalie; McCann, Ben; Poiana, Peter

    2015-01-01

    Throughout this book, the concept of framing is used to look at art, photography, scientific drawings and cinema as visually constituted, spatially bounded productions. The way these genres relate to that which exists beyond the frame, by means of plastic, chemically transposed, pencil-sketched or moving images allows us to decipher the particular language of the visual and at the same time circumscribe the dialectic between presence and absence that is proper to all visual media. Yet, these ...

  9. Theory of vibration protection

    CERN Document Server

    Karnovsky, Igor A

    2016-01-01

    This text is an advancement of the theory of vibration protection of mechanical systems with lumped and distributed parameters. The book offers various concepts and methods of solving vibration protection problems, discusses the advantages and disadvantages of different methods, and the fields of their effective applications. Fundamental approaches of vibration protection, which are considered in this book, are the passive, parametric and optimal active vibration protection. The passive vibration protection is based on vibration isolation, vibration damping and dynamic absorbers. Parametric vibration protection theory is based on the Shchipanov-Luzin invariance principle. Optimal active vibration protection theory is based on the Pontryagin principle and the Krein moment method. The book also contains special topics such as suppression of vibrations at the source of their occurrence and the harmful influence of vibrations on humans. Numerous examples, which illustrate the theoretical ideas of each chapter, ar...

  10. On transforms between Gabor frames and wavelet frames

    DEFF Research Database (Denmark)

    Christensen, Ole; Goh, Say Song

    2013-01-01

    We describe a procedure that enables us to construct dual pairs of wavelet frames from certain dual pairs of Gabor frames. Applying the construction to Gabor frames generated by appropriate exponential Bsplines gives wavelet frames generated by functions whose Fourier transforms are compactly...... supported splines with geometrically distributed knot sequences. There is also a reverse transform, which yields pairs of dual Gabor frames when applied to certain wavelet frames....

  11. The Optimum Slash Pile Size for Grinding Operations: Grapple Excavator and Horizontal Grinder Operations Model Based on a Sierra Nevada, California Survey

    Directory of Open Access Journals (Sweden)

    Takuyuki Yoshioka

    2017-11-01

    Full Text Available The processing of woody biomass waste piles for use as fuel instead of burning them was investigated. At each landing of slash pile location, a 132 kW grapple excavator was used to transfer the waste piles into a 522 kW horizontal grinder. Economies of scale could be expected when grinding a larger pile, although the efficiency of the loading operation might be diminished. Here, three piles were ground and the operations were time-studied: Small (20 m long × 15 m wide × 4 m high, Medium (30 × 24 × 4 m, and Large (35 × 30 × 4 m piles. Grinding the Medium pile was found to be the most productive at 30.65 bone dry tons per productive machine hour without delay (BDT/PMH0, thereby suggesting that there might be an optimum size of slash pile for a grinding operation. Modeling of the excavator and grinder operations was also examined, and the constructed simulation model was observed to well-replicate the actual operations. Based on the modeling, the productivity of grinding at a landing area of 710 m2 of slash pile location was estimated to be 31.24 BDT/PMH0, which was the most productive rate.

  12. Type of frame dependence: variation in media frames affecting attitudes via audience frames

    NARCIS (Netherlands)

    van Drunen, A.S.; Boomgaarden, H.G.; Vliegenthart, R.

    2012-01-01

    In this paper two suggested processes of framing theory (Scheufele, 1999) are tested: frame setting (media affecting audience frames) and the individual effects process (audience frames affecting attitudes or behavior). Media frames may affect opinions and behavior, however these effects are not

  13. Perceptual frames in frequency estimation.

    Science.gov (United States)

    Zyłowska, Aleksandra; Kossek, Marcin; Wawrzyniak, Małgorzata

    2014-02-01

    This study is an introductory investigation of cognitive frames, focused on perceptual frames divided into information and formal perceptual frames, which were studied based on sub-additivity of frequency estimations. It was postulated that different presentations of a response scale would result in different percentage estimates of time spent watching TV or using the Internet. The results supported the existence of perceptual frames that influence the perception process and indicated that information perceptual frames had a stronger effect than formal frames. The measures made possible the exploration of the operation of perceptual frames and also outlined the relations between heuristics and cognitive frames.

  14. Operator representations of frames

    DEFF Research Database (Denmark)

    Christensen, Ole; Hasannasab, Marzieh

    2017-01-01

    The purpose of this paper is to consider representations of frames {fk}k∈I in a Hilbert space ℋ of the form {fk}k∈I = {Tkf0}k∈I for a linear operator T; here the index set I is either ℤ or ℒ0. While a representation of this form is available under weak conditions on the frame, the analysis...... of the properties of the operator T requires more work. For example it is a delicate issue to obtain a representation with a bounded operator, and the availability of such a representation not only depends on the frame considered as a set, but also on the chosen indexing. Using results from operator theory we show...... that by embedding the Hilbert space ℋ into a larger Hilbert space, we can always represent a frame via iterations of a bounded operator, composed with the orthogonal projection onto ℋ. The paper closes with a discussion of an open problem concerning representations of Gabor frames via iterations of a bounded...

  15. Resonant vibration control of wind turbine blades

    DEFF Research Database (Denmark)

    Svendsen, Martin Nymann; Krenk, Steen; Høgsberg, Jan Becker

    2010-01-01

    The paper deals with introduction of damping to specific vibration modes of wind turbine blades, using a resonant controller with acceleration feedback. The wind turbine blade is represented by three-dimensional, two-node finite elements in a local, rotating frame of reference. The element....... The efficiency of the resonant controller is demonstrated for a representative turbine blade exposed to turbulent wind loading. It is found that the present explicit tuning procedure yields close to optimal tuning, with very limited modal spill-over and effective reduction of the vibration amplitudes....

  16. Riesz frames and approximation of the frame coefficients

    DEFF Research Database (Denmark)

    Casazza, P.; Christensen, Ole

    1998-01-01

    A frame is a fmaily {f i } i=1 ∞ of elements in a Hilbert space with the property that every element in can be written as a (infinite) linear combination of the frame elements. Frame theory describes how one can choose the corresponding coefficients, which are called frame coefficients. From...

  17. Fusion frames and G-frames in Banach spaces

    Indian Academy of Sciences (India)

    Soc., Providence, RI) (1999). [4] Casazza P G and Kutyniok G, Frames of subspaces, Wavelets, frames and operator theory, pp. 87–113, Contemp. Math. 345 (Amer. Math. Soc., Providence, RI) (2004). [5] Casazza P G and Kutyniok G, Robustness of fusion frames under erasures of subspaces and of local frame vectors, ...

  18. Analog Frame Store Memory.

    Science.gov (United States)

    1980-01-15

    enhancement when coupled with the video acquisition performed by the Frame Store Memory in mode 2. 3 -11 It cr (A 3 coJ 0( kLL P.- FAIRCHILO IMAGING ...AD-AOSI 979 FAIRCHILD IMAGING SYSTEMS SYOSSET N Y F/0 17/2 ANALOG FRAME STORE MEMORY . CU) JAN 80 OAAK77-C-0165 UNCLASSIFIED ED-CX-141-5 M 1 .0 H " 1...DESCRIPTION 1-2 1.1.1 Analog Frame Store Memory 1-2 1.1.2 Analog Field Storage Device 1-4 1.1.3 Image Analyzer Digital Display (IADD) 1-4 1.2 PROGRAM’S

  19. Framing the Newspaper Crisis

    DEFF Research Database (Denmark)

    Bruggemann, Michael; Humprecht, Edda; Kleis, Rasmus

    2016-01-01

    as well as a qualitative analysis of policy documents and relevant media coverage. The study demonstrates that debates on the newspaper crisis are only partly influenced by (1) economic realities and (2) media policy traditions in the six countries but also reflect (3) the strategic motives of powerful......This article argues that discourses of a newspaper crisis should not be regarded simply as descriptions of the actual state of the press but also as a means by which strategic actors frame the situation. The emerging frames can have substantial consequences for media policy making. The study...... identifies four key frames used to portray the newspaper crisis and discusses their relevance for public debates in Finland, France, Germany, Italy, the United Kingdom and the United States. Similarities and differences are examined through 59 in-depth interviews with policymakers and industry executives...

  20. Framing financial culture

    DEFF Research Database (Denmark)

    Just, Sine Nørholm; Mouton, Nicolaas T.O.

    2014-01-01

    between competing frames leads to the conclusion that this political “blame game” is related to struggles over how to define the scandal, how to conceptualize its causes, and policy recommendations. Banks may have lost the battle of “Liborgate,” but the war over the meaning of financial culture is far...... from over. Originality/value – The paper is theoretically and methodologically original in its combination of the theories of framing and stasis, and it provides analytical insights into how sense is made of financial culture in the wake of the financial crisis....

  1. Institutional Justification in Frames

    DEFF Research Database (Denmark)

    Baden, Christian; Schultz, Friederike

    Crises – such as the BP oil spill in the Gulf of Mexico (2010) – are moments in which conventional interpretations break down. This paper analyzes the dynamics of the re-construction and stabilization of meaning in the public debate and assesses how BP’s strategic framing affected the emerging...... consensus. It extents research on framing in mass communication by applying institutional theory and Boltanski and Thévenot’s (2006) theory on justification in order to explain how the success and failure of proposed interpretations depend on the mobilization of accepted social institutions to justify...

  2. Timber frame walls

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan de Place; Brandt, Erik

    2010-01-01

    A ventilated cavity is usually considered good practice for removing moisture behind the cladding of timber framed walls. Timber frame walls with no cavity are a logical alternative as they are slimmer and less expensive to produce and besides the risk of a two-sided fire behind the cladding...... is reduced. To investigate the possibilities, full-size wall elements with wooden cladding and different cavity design, type of cladding and type of wind barrier were exposed to natural climate on the outside and to a humid indoor climate on the inside. During the exposure period parts of the vapour barrier...

  3. Frames and extension problems I

    DEFF Research Database (Denmark)

    Christensen, Ole

    2014-01-01

    In this article we present a short survey of frame theory in Hilbert spaces. We discuss Gabor frames and wavelet frames and set the stage for a discussion of various extension principles; this will be presented in the article Frames and extension problems II (joint with H.O. Kim and R.Y. Kim)....

  4. Aluminum automotive space frames

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-08-01

    Design of aluminum structures is to a new topic. Aircraft makers have successfully solved difficult structural problems with a high degree of understanding and reliability. Other transportation modes such as trucks, trailers, and railcars have faced structural problems with some emphasis on high- and low-cycle fatigue of welded aluminum structures. However, the automotive market places stringent engineering demands on materials and superimposes demanding cost constraints. A project was instituted at Reynolds Metals Co. to investigate the opportunities for the cost-effective application of aluminum to automotive spaceframes. Several areas were recognized as key to the success of this application. They were: equivalent or superior structural stiffness of the assembly to existing steel unibody and/or steel spaceframe vehicles; effective joining of spaceframe members; equivalent or superior crashworthiness of the assembly; weight savings; flexibility; and low-cost approach aimed at effective manufacturing. To gain experience with the key aspects in a practical environment, the experience of current builders of steel tube frame chassis was explored. These chassis are typically used in low-volume vehicles requiring torsional stiffness, excellent crashworthiness, and exterior body-style flexibility. A model was developed using finite element methods that accurately predicts mass and stiffness of frames. An effective aluminum space frame was generated which was 7.5% stiffer and more than 20% lighter than the steel frame, with stresses kept below the fatigue limit for aluminum welds.

  5. What's in a frame?

    DEFF Research Database (Denmark)

    Holmgreen, Lise-Lotte

    of meaning. In Proceedings of the First Annual Meeting of the Berkeley Linguistics Society, 123-131. Amsterdam: North Holland. Fillmore, Charles. 1982. Frame semantics. In Linguistics in the Morning Calm, Linguistic Society of Korea (ed.), 111-137. Seoul: Hanshin Publishing. Gunnarsson, Britt-Louise. 2009...

  6. The Cage; Framing Dad

    DEFF Research Database (Denmark)

    Kau, Edvin

    2012-01-01

    Unfolding his story very gradually and arousing the viewer’s curiosity, Sitaru invites the audience to investigate the parents’ and the boy’s mutual positions in their small flat, as well as the various layers of their conversations, through such means as framing, editing style, and the use...

  7. Framing a Bank

    DEFF Research Database (Denmark)

    Holmgreen, Lise-Lotte

    2012-01-01

    in the information given. However, in this process the organisation is not operating in a social vacuum but is continuously interacting with various players, such as the media, for its discursive construction. This article will focus on the role of this interaction in metaphorically and conceptually framing a large...

  8. FishFrame

    DEFF Research Database (Denmark)

    Degel, Henrik; Jansen, Teunis

    2006-01-01

    . Development and test of software modules can be done once and reused by all. The biggest challenge in this is not technical – it is in organisation, coordination and trust. This challenge has been addressed by FishFrame - a web-based datawarehouse application. The “bottom-up” approach with maximum involvement...

  9. Framing the Oscars live

    DEFF Research Database (Denmark)

    Haastrup, Helle Kannik

    2016-01-01

    How is the global media event of the Oscars localised through the talk show on Danish television? How are both the mediated film star and the special brand of Hollywood celebrity culture addressed by the cultural intermediaries in the Danish framing? These are the questions I propose to answer th...... through a brief analysis of the Academy Awards live broadcast on Danish television....

  10. Popcorn Story Frames.

    Science.gov (United States)

    DiLella, Carol Ann

    This paper presents "popcorn story frames"--holistic outlines that facilitate comprehension when reading and writing stories, useful for outlining stories read and for creating outlines for original student stories--that are particularly useful for elementary and intermediate school students. "Popcorn" pops in a horizontal…

  11. Framing Light Rail Projects

    DEFF Research Database (Denmark)

    Olesen, Mette

    2014-01-01

    In Europe, there has been a strong political will to implement light rail. This article contributes to the knowledge concerning policies around light rail by analysing how local actors frame light rail projects and which rationalities and arguments are present in this decision-making process...

  12. What's in a Frame?

    DEFF Research Database (Denmark)

    Holmgreen, Lise-Lotte

    Maintaining a good image and reputation in the eyes of stakeholders is vital to the organisation. Thus, in its corporate communication and discourse the organisation will seek to present or frame itself as favourably as possible while observing regulations stipulating accuracy and precision...

  13. Framing ‘fracking’

    NARCIS (Netherlands)

    Williams, Laurence; Macnaghten, Philip; Davies, Richard; Curtis, Sarah

    2017-01-01

    The prospect of fracking in the United Kingdom has been accompanied by significant public unease. We outline how the policy debate is being framed by UK institutional actors, finding evidence of a dominant discourse in which the policy approach is defined through a deficit model of public

  14. Framing Canadian federalism

    National Research Council Canada - National Science Library

    Saywell, John; Anastakis, Dimitry; Bryden, Penny E

    2009-01-01

    ... the pervasive effects that federalism has on Canadian politics, economics, culture, and history, and provide a detailed framework in which to understand contemporary federalism. Written in honour of John T. Saywell's half-century of accomplished and influential scholarly work and teaching, Framing Canadian Federalism is a timely and fitting t...

  15. Sparse Matrices in Frame Theory

    DEFF Research Database (Denmark)

    Lemvig, Jakob; Krahmer, Felix; Kutyniok, Gitta

    2014-01-01

    Frame theory is closely intertwined with signal processing through a canon of methodologies for the analysis of signals using (redundant) linear measurements. The canonical dual frame associated with a frame provides a means for reconstruction by a least squares approach, but other dual frames...... yield alternative reconstruction procedures. The novel paradigm of sparsity has recently entered the area of frame theory in various ways. Of those different sparsity perspectives, we will focus on the situations where frames and (not necessarily canonical) dual frames can be written as sparse matrices...

  16. Some relationship between G-frames and frames

    Directory of Open Access Journals (Sweden)

    Mehdi Rashidi-Kouchi

    2015-06-01

    Full Text Available In this paper we proved that every g-Riesz basis for Hilbert space $H$ with respect to $K$ by adding a condition is a Riesz basis for Hilbert $B(K$-module $B(H,K$. This is an extension of [A. Askarizadeh,M. A. Dehghan, {em G-frames as special frames}, Turk. J. Math., 35, (2011 1-11]. Also, we derived similar results for g-orthonormal and orthogonal bases. Some relationships between dual frame, dual g-frame and exact frame and exact g-frame are presented too.

  17. Meat batter production in an extended vane pump-grinder injecting curing salt solutions to reduce energy requirements: variation of curing salt amount injected with the solution.

    Science.gov (United States)

    Irmscher, Stefan B; Terjung, Eva-Maria; Gibis, Monika; Herrmann, Kurt; Kohlus, Reinhard; Weiss, Jochen

    2017-01-01

    The integration of a nozzle in an extended vane pump-grinder system may enable the continuous injection of curing salt solutions during meat batter production. The purpose of this work was to examine the influence of the curing salt amount injected with the solution (0-100%) on protein solubilisation, water-binding, structure, colour and texture of emulsion-type sausages. The amount of myofibrillar protein solubilised during homogenisation varied slightly from 33 to 36 g kg(-1) . Reddening was not noticeably impacted by the later addition of nitrite. L(*) ranged from 66.9 ± 0.3 to 67.8 ± 0.3, a(*) from 10.9 ± 0.1 to 11.2 ± 0.1 and b(*) from 7.7 ± 0.1 to 8.0 ± 0.1. Although softer sausages were produced when only water was injected, firmness increased with increasing curing salt amount injected and was similar to the control when the full amount of salt was used. The substitution of two-thirds of ice with a liquid brine may enable energy savings due to reduced power consumptions of the extended vane pump-grinder system by up to 23%. The injection of curing salt solutions is feasible without affecting structure and colour negatively. This constitutes a first step towards of an 'ice-free' meat batter production allowing for substantial energy savings due to lower comminution work. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  18. Wind Turbine Rotors with Active Vibration Control

    DEFF Research Database (Denmark)

    Svendsen, Martin Nymann

    This thesis presents a framework for structural modeling, analysis and active vibration damping of rotating wind turbine blades and rotors. A structural rotor model is developed in terms of finite beam elements in a rotating frame of reference. The element comprises a representation of general...... formulation. The element provides an accurate representation of the eigenfrequencies and whirling modes of the gyroscopic system, and identifies lightly damped edge-wise modes. By adoption of a method for active, collocated resonant vibration of multi-degree-of-freedom systems it is demonstrated...... that these are geometrically well separated. For active vibration control in three-bladed wind turbine rotors the present work presents a resonance-based method for groups of one collective and two whirling modes. The controller is based on the existing resonant format and introduces a dual system targeting the collective...

  19. Mechanical vibration to electrical energy converter

    Science.gov (United States)

    Kellogg, Rick Allen [Tijeras, NM; Brotz, Jay Kristoffer [Albuquerque, NM

    2009-03-03

    Electromechanical devices that generate an electrical signal in response to an external source of mechanical vibrations can operate as a sensor of vibrations and as an energy harvester for converting mechanical vibration to electrical energy. The devices incorporate a magnet that is movable through a gap in a ferromagnetic circuit, wherein a coil is wound around a portion of the ferromagnetic circuit. A flexible coupling is used to attach the magnet to a frame for providing alignment of the magnet as it moves or oscillates through the gap in the ferromagnetic circuit. The motion of the magnet can be constrained to occur within a substantially linear range of magnetostatic force that develops due to the motion of the magnet. The devices can have ferromagnetic circuits with multiple arms, an array of magnets having alternating polarity and, encompass micro-electromechanical (MEM) devices.

  20. Wavelet frames and their duals

    DEFF Research Database (Denmark)

    Lemvig, Jakob

    2008-01-01

    frames with good time localization and other attractive properties. Furthermore, the dual wavelet frames are constructed in such a way that we are guaranteed that both frames will have the same desirable features. The construction procedure works for any real, expansive dilation. A quasi-affine system....... The signals are then represented by linear combinations of the building blocks with coefficients found by an associated frame, called a dual frame. A wavelet frame is a frame where the building blocks are stretched (dilated) and translated versions of a single function; such a frame is said to have wavelet...... structure. The dilation of the wavelet building blocks in higher dimension is done via a square matrix which is usually taken to be integer valued. In this thesis we step away from the "usual" integer, expansive dilation and consider more general, expansive dilations. In most applications of wavelet frames...

  1. Work and Inertial Frames

    Science.gov (United States)

    Kaufman, Richard

    2017-12-01

    A fairly recent paper resolves a large discrepancy in the internal energy utilized to fire a cannon as calculated by two inertial observers. Earth and its small reaction velocity must be considered in the system so that the change in kinetic energy is calculated correctly. This paper uses a car in a similar scenario, but considers the work done by forces acting over distances. An analysis of the system must include all energy interactions, including the work done on the car and especially the (negative) work done on Earth in a moving reference frame. This shows the importance of considering the force on Earth and the distance Earth travels. For calculation of work in inertial reference frames, the center of mass perspective is shown to be useful. We also consider the energy requirements to efficiently accelerate a mass among interacting masses.

  2. Density of Gabor Frames

    DEFF Research Database (Denmark)

    Christensen, Ole; Heil, C.; Deng, B.

    1997-01-01

    A Gabor system is a set of time-frequency shifts$S(g,\\Lambda) = \\{e^{2\\pi i b x} g(x-a)\\}_{(a,b) \\in \\Lambda}$of a function $g \\in L^2({\\bold R}^d)$.We prove that if a finite union of Gabor systems$\\bigcup_{k=1}^r S(g_k,\\Lambda_k)$, with arbitrary sequences $\\Lambda_k$,forms a frame for $L^2({\\bo...

  3. Frame for a firearm

    Science.gov (United States)

    Crandall, David L [Idaho Falls, ID; Watson, Richard W [Blackfoot, ID

    2008-03-04

    A firearm frame which is adapted to be disposed in operative relationship as a component part of a firearm, the firearm having disposed in operative relationships each with one or more of the others, a barrel, a receiver, and at least one firing mechanism; wherein the barrel and receiver form operative parts of a movable assembly and the at least one firing mechanism is disposed in a substantially stationary operative relationship therewith; the firearm frame including at least one elongated support structure discrete from the barrel and receiver, the elongated support structure being adapted to directly support the movable assembly in an operative movable relationship therewith; whereby at least one of the barrel and receiver is in direct contact with and movable on the elongated support structure; and, a firing mechanism support structure connected to the at least one elongated support structure, the firing mechanism support structure being adapted to have the firing mechanism connected thereto; the firearm frame also directly supporting the movable assembly and the firing mechanism in corresponding movable and stationary operative relationships each with the other.

  4. Tunable Passive Vibration Suppressor

    Science.gov (United States)

    Boechler, Nicholas (Inventor); Dillon, Robert Peter (Inventor); Daraio, Chiara (Inventor); Davis, Gregory L. (Inventor); Shapiro, Andrew A. (Inventor); Borgonia, John Paul C. (Inventor); Kahn, Daniel Louis (Inventor)

    2016-01-01

    An apparatus and method for vibration suppression using a granular particle chain. The granular particle chain is statically compressed and the end particles of the chain are attached to a payload and vibration source. The properties of the granular particles along with the amount of static compression are chosen to provide desired filtering of vibrations.

  5. Vibrations and Eigenvalues

    Indian Academy of Sciences (India)

    We make music by causing strings, membranes, or air columns to vibrate. Engineers design safe structures by control- ling vibrations. I will describe to you a very simple vibrating system and the mathematics needed to analyse it. The ideas were born in the work of Joseph-Louis Lagrange (1736–1813), and I begin by quot-.

  6. Electrodynamics in accelerated frames revisited

    Energy Technology Data Exchange (ETDEWEB)

    Maluf, J.W. [Instituto de Fisica, Universidade de Brasilia (Brazil); Ulhoa, S.C. [Instituto de Ciencia e Tecnologia, Universidade Federal dos Vales do Jequitinhonha e Mucuri, UFVJM, Diamantina, MG (Brazil)

    2010-10-15

    Maxwell's equations are formulated in arbitrary moving frames by means of tetrad fields, which are interpreted as reference frames adapted to observers in space-time. We assume the existence of a general distribution of charges and currents in an inertial frame. Tetrad fields are used to project the electromagnetic fields and sources on accelerated frames. The purpose is to study several configurations of fields and observers that in the literature are understood as paradoxes. For instance, are the two situations, (i) an accelerated charge in an inertial frame, and (ii) a charge at rest in an inertial frame described from the perspective of an accelerated frame, physically equivalent? Is the electromagnetic radiation the same in both frames? Normally in the analysis of these paradoxes the electromagnetic fields are transformed to (uniformly) accelerated frames by means of a coordinate transformation of the Faraday tensor. In the present approach coordinate and frame transformations are disentangled, and the electromagnetic field in the accelerated frame is obtained through a frame (local Lorentz) transformation. Consequently the fields in the inertial and accelerated frames are described in the same coordinate system. This feature allows the investigation of paradoxes such as the one mentioned above. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  7. VIOLENT FRAMES IN ACTION

    Energy Technology Data Exchange (ETDEWEB)

    Sanfilippo, Antonio P.; McGrath, Liam R.; Whitney, Paul D.

    2011-11-17

    We present a computational approach to radical rhetoric that leverages the co-expression of rhetoric and action features in discourse to identify violent intent. The approach combines text mining and machine learning techniques with insights from Frame Analysis and theories that explain the emergence of violence in terms of moral disengagement, the violation of sacred values and social isolation in order to build computational models that identify messages from terrorist sources and estimate their proximity to an attack. We discuss a specific application of this approach to a body of documents from and about radical and terrorist groups in the Middle East and present the results achieved.

  8. Continuous Shearlet Tight Frames

    KAUST Repository

    Grohs, Philipp

    2010-10-22

    Based on the shearlet transform we present a general construction of continuous tight frames for L2(ℝ2) from any sufficiently smooth function with anisotropic moments. This includes for example compactly supported systems, piecewise polynomial systems, or both. From our earlier results in Grohs (Technical report, KAUST, 2009) it follows that these systems enjoy the same desirable approximation properties for directional data as the previous bandlimited and very specific constructions due to Kutyniok and Labate (Trans. Am. Math. Soc. 361:2719-2754, 2009). We also show that the representation formulas we derive are in a sense optimal for the shearlet transform. © 2010 Springer Science+Business Media, LLC.

  9. The Levels of Visual Framing

    Science.gov (United States)

    Rodriguez, Lulu; Dimitrova, Daniela V.

    2011-01-01

    While framing research has centered mostly on the evaluations of media texts, visual news discourse has remained relatively unexamined. This study surveys the visual framing techniques and methods employed in previous studies and proposes a four-tiered model of identifying and analyzing visual frames: (1) visuals as denotative systems, (2) visuals…

  10. New avenues for framing research

    NARCIS (Netherlands)

    de Vreese, C.H.

    2012-01-01

    In this article, the author reviews the studies in this special issue of the American Behavioral Scientist. It is a strong collection of articles reporting findings from an integrated project that looks at frame building, frames, and effects of frames. The project is part of an exciting large-scale

  11. Vibration analysis of cryocoolers

    Science.gov (United States)

    Tomaru, Takayuki; Suzuki, Toshikazu; Haruyama, Tomiyoshi; Shintomi, Takakazu; Yamamoto, Akira; Koyama, Tomohiro; Li, Rui

    2004-05-01

    The vibrations of Gifford-McMahon (GM) and pulse-tube (PT) cryocoolers were measured and analyzed. The vibrations of the cold-stage and cold-head were measured separately to investigate their vibration mechanisms. The measurements were performed while maintaining the thermal conditions of the cryocoolers at a steady state. We found that the vibration of the cold-head for the 4 K PT cryocooler was two orders of magnitude smaller than that of the 4 K GM cryocooler. On the other hand, the vibration of the cold-stages for both cryocoolers was of the same order of magnitude. From a spectral analysis of the vibrations and a simulation, we concluded that the vibration of the cold-stage is caused by an elastic deformation of the pulse tubes (or cylinders) due to the pressure oscillation of the working gas.

  12. Vibration analysis of cryocoolers

    Energy Technology Data Exchange (ETDEWEB)

    Tomaru, Takayuki; Suzuki, Toshikazu; Haruyama, Tomiyoshi; Shintomi, Takakazu; Yamamoto, Akira [High Energy Accelerator Research Organization (KEK), Tsukuba, Ibaraki (Japan); Koyama, Tomohiro; Rui Li [Sumitomo Heavy Industries Ltd., Tokyo (Japan)

    2004-05-01

    The vibrations of Gifford-McMahon (GM) and pulse-tube (PT) cryocoolers were measured and analyzed. The vibrations of the cold-stage and cold-head were measured separately to investigate their vibration mechanisms. The measurements were performed while maintaining the thermal conditions of the cryocoolers at a steady state. We found that the vibration of the cold-head for the 4 K PT cryocooler was two orders of magnitude smaller than that of the 4 K GM cryocooler. On the other hand, the vibration of the cold-stages for both cryocoolers was of the same order of magnitude. From a spectral analysis of the vibrations and a simulation, we concluded that the vibration of the cold-stage is caused by an elastic deformation of the pulse tubes (or cylinders) due to the pressure oscillation of the working gas. (Author)

  13. Vibration of hydraulic machinery

    CERN Document Server

    Wu, Yulin; Liu, Shuhong; Dou, Hua-Shu; Qian, Zhongdong

    2013-01-01

    Vibration of Hydraulic Machinery deals with the vibration problem which has significant influence on the safety and reliable operation of hydraulic machinery. It provides new achievements and the latest developments in these areas, even in the basic areas of this subject. The present book covers the fundamentals of mechanical vibration and rotordynamics as well as their main numerical models and analysis methods for the vibration prediction. The mechanical and hydraulic excitations to the vibration are analyzed, and the pressure fluctuations induced by the unsteady turbulent flow is predicted in order to obtain the unsteady loads. This book also discusses the loads, constraint conditions and the elastic and damping characters of the mechanical system, the structure dynamic analysis, the rotor dynamic analysis and the system instability of hydraulic machines, including the illustration of monitoring system for the instability and the vibration in hydraulic units. All the problems are necessary for vibration pr...

  14. Vehicle frame measurement device

    Energy Technology Data Exchange (ETDEWEB)

    Sarauer, A.J.

    1987-08-04

    This patent describes a vehicle frame and body measurement apparatus for use in realigning the structure of a damaged unibody vehicle the device having a longitudinal axis utilized in a horizontal plane the apparatus comprising means for measuring the vehicle body and frame comprising, (a) means for supporting a damaged motor vehicle in a fixed position, (b) an elongated rail on each side of the supporting means spaced apart a distance greater than the width of the supporting means and the width of the vehicle, (c) a vertical upright of a length exceeding the height of the motor vehicle slidably supported by each of the rails and having a vertical axis substantially perpendicular to the horizontal plane of the vehicle, (d) a vertically adjustable horizontal bar attached to each of the uprights, substantially perpendicular to both the longitudinal axis of the rails and the vertical axis of the uprights, (e) means for affixing the horizontal bar to the uprights so that the bar is vertically adjustable, the affixing means being provided with releasable means to permit adjustable horizontal extension of the horizontal bar and (f) at least one extendable measuring means attached to each vertical upright at its junction with its associated horizontal rail and adjustably extending along the horizontal rail, the free end of the measuring means having to releasably affix it to the rail.

  15. Mapping in inertial frames

    Energy Technology Data Exchange (ETDEWEB)

    Arunasalam, V.

    1989-05-01

    World space mapping in inertial frames is used to examine the Lorentz covariance of symmetry operations. It is found that the Galilean invariant concepts of simultaneity (S), parity (P), and time reversal symmetry (T) are not Lorentz covariant concepts for inertial observers. That is, just as the concept of simultaneity has no significance independent of the Lorentz inertial frame, likewise so are the concepts of parity and time reversal. However, the world parity (W) (i.e., the space-time reversal symmetry (P-T)) is a truly Lorentz covariant concept. Indeed, it is shown that only those mapping matrices M that commute with the Lorentz transformation matrix L (i.e., (M,L) = 0) are the ones that correspond to manifestly Lorentz covariant operations. This result is in accordance with the spirit of the world space Mach's principle. Since the Lorentz transformation is an orthogonal transformation while the Galilean transformation is not an orthogonal transformation, the formal relativistic space-time mapping theory used here does not have a corresponding non-relativistic counterpart. 12 refs.

  16. on Goal Framing

    Directory of Open Access Journals (Sweden)

    Eulàlia P. Abril

    2014-01-01

    Full Text Available En respuesta a la enorme y algunas veces conceptualmente inconsistente literatura sobre valence framing,Levin y sus colegas (1998 desarrollaron una tipología de encuadre de valencia que organiza los diferentesresultados a partir de elección arriesgada, atributo, y encuadre de los resultados (goal framing. Este estudiofavorece la literatura sobre encuadre de los resultados mediante (a su aplicación en el contexto de una cuestiónsocial como la pobreza infantil extrema; y (b el examen de los mecanismos afectivos sobre el cual el encuadrede los resultados es de eficacia persuasiva. Los resultados experimentales (N = 197 mostraron que la exposiciónal mensaje de encuadre de pérdida permitió un apoyo mayor hacia las políticas públicas que buscan erradicar lapobreza infantil, en comparación con el mensaje de encuadre de ganancia. Los resultados también revelaronque el afecto negativo sirve como herramienta mediadora de apoyo hacia las políticas públicas. Estos hallazgossugieren que, en el contexto del apoyo social hacia la población pobre, la capacidad de persuasión dentro delencuadre de pérdida se facilita cuando los participantes experimentan afectos negativos.

  17. Do frame à pintura

    OpenAIRE

    Haddad, João Müller

    2011-01-01

    A pesquisa parte do encontro, na arte contemporânea, entre meios artísticos (mídias analógicas e digitais), possibilitado pela utilização de meios tecnológicos. Trata, mais especificamente, da materialidade e imaterialidade das linguagens da pintura e do vídeo, se pautando na produção de artistas da cena contemporânea, Romanita Disconzi, e minha própria produção poética. A investigação poética trata da transposição de frames, instantes, parte mínima divisível de cenas de corpos humanos em mov...

  18. Behaviour of Strengthened RC Frames with Eccentric Steel Braced Frames

    Directory of Open Access Journals (Sweden)

    Kamanli Mehmet

    2017-01-01

    Full Text Available After devastating earthquakes in recent years, strengthening of reinforced concrete buildings became an important research topic. Reinforced concrete buildings can be strengthened by steel braced frames. These steel braced frames may be made of concentrically or eccentrically indicated in Turkish Earthquake Code 2007. In this study pushover analysis of the 1/3 scaled 1 reinforced concrete frame and 1/3 scaled 4 strengthened reinforced concrete frames with internal eccentric steel braced frames were conducted by SAP2000 program. According to the results of the analyses conducted, load-displacement curves of the specimens were compared and evaluated. Adding eccentric steel braces to the bare frame decreased the story drift, and significantly increased strength, stiffness and energy dissipation capacity. In this strengthening method lateral load carrying capacity, stiffness and dissipated energy of the structure can be increased.

  19. Behaviour of Strengthened RC Frames with Eccentric Steel Braced Frames

    Science.gov (United States)

    Kamanli, Mehmet; Unal, Alptug

    2017-10-01

    After devastating earthquakes in recent years, strengthening of reinforced concrete buildings became an important research topic. Reinforced concrete buildings can be strengthened by steel braced frames. These steel braced frames may be made of concentrically or eccentrically indicated in Turkish Earthquake Code 2007. In this study pushover analysis of the 1/3 scaled 1 reinforced concrete frame and 1/3 scaled 4 strengthened reinforced concrete frames with internal eccentric steel braced frames were conducted by SAP2000 program. According to the results of the analyses conducted, load-displacement curves of the specimens were compared and evaluated. Adding eccentric steel braces to the bare frame decreased the story drift, and significantly increased strength, stiffness and energy dissipation capacity. In this strengthening method lateral load carrying capacity, stiffness and dissipated energy of the structure can be increased.

  20. Riesz Frames and Approximation of the Frame Coefficients

    DEFF Research Database (Denmark)

    Christensen, Ole

    1996-01-01

    A frame is a familyof elements in a Hilbert space with the propertythat every element in the Hilbert space can be written as a (infinite)linear combination of the frame elements. Frame theory describes howone can choose the corresponding coefficients, which are calledframe coefficients. From...... the mathematical point of view this isgratifying, but for applications it is a problem that the calculationrequires inversion of an operator on the Hilbert space.The projection method is introduced in order to avoid this problem.The basic idea is to consider finite subfamiliesof the frame and the orthogonal...

  1. TRU-FRAME Steel Truss

    OpenAIRE

    ECT Team, Purdue

    2007-01-01

    After earthquakes, repair and replacement of structural elements is time consuming and expensive. This new truss system contains several diagonal elements designed to absorb seismic energy and yield at prescribed levels. Standard moment frame design requires 100% visual inspection and ultrasonic testing which is eliminated when using the Tru-Frame system. Since all Tru-Frame connections are single pass fillet welds and tension control bolts, they can be visually inspected any time after compl...

  2. Inertial Frames and Clock Rates

    CERN Document Server

    Kak, Subhash

    2012-01-01

    This article revisits the historiography of the problem of inertial frames. Specifically, the case of the twins in the clock paradox is considered to see that some resolutions implicitly assume inertiality for the non-accelerating twin. If inertial frames are explicitly identified by motion with respect to the large scale structure of the universe, it makes it possible to consider the relative inertiality of different frames.

  3. Six problems in frame theory

    DEFF Research Database (Denmark)

    Christensen, Ole

    2014-01-01

    We discuss various problems in frame theory that have been open for some years. A short discussion of frame theory is also provided, but it only contains the information that is necessary in order to understand the open problems and their role.......We discuss various problems in frame theory that have been open for some years. A short discussion of frame theory is also provided, but it only contains the information that is necessary in order to understand the open problems and their role....

  4. Incomplete sanitation of a meat grinder and ingestion of raw ground beef: contributing factors to a large outbreak of Salmonella typhimurium infection.

    Science.gov (United States)

    Roels, T H; Frazak, P A; Kazmierczak, J J; Mackenzie, W R; Proctor, M E; Kurzynski, T A; Davis, J P

    1997-10-01

    Consumers in the United States continue to eat raw or undercooked foods of animal origin despite public health warnings following several well-publicized outbreaks. We investigated an outbreak of Salmonella serotype Typhimurium infection in 158 patients in Wisconsin during the 1994 Christmas holiday period. To determine the vehicle and source of the outbreak, we conducted cohort and case-control studies, and environmental investigations in butcher shop A. Eating raw ground beef purchased from butcher shop A was the only item significantly associated with illness [cohort study: relative risk = 5.8, 95% confidence interval (CI) = 1.5-21.8; case control study: odds ratio = 46.2, 95% CI = 3.8-2751]. Inadequate cleaning and sanitization of the meat grinder in butcher shop A likely resulted in sustained contamination of ground beef during an 8-day interval. Consumer education, coupled with hazard reduction efforts at multiple stages in the food processing chain, will continue to play an important role in the control of foodborne illness.

  5. Power to the frame: bringing sociology back to frame analysis

    NARCIS (Netherlands)

    Vliegenthart, R.; van Zoonen, L.

    2011-01-01

    This article critically reviews current frame and framing research in media and communication studies. It is first argued that most authors fail to distinguish between ‘frame’ and ‘framing’ and therewith produce a conceptual confusion and imprecision that is not conducive to the field. Second, it is

  6. column frame for design of reinforced concrete sway frames

    African Journals Online (AJOL)

    adminstrator

    Journal, proceedings, 2009, pp.24-48. 11. Ewnetie A., Investigation on Applicability of Substitute Beam-Column Frame for. Design of Reinforced Concrete Sway. Frames, MSc Thesis, 2012. Notations. ACI: American Concrete Institute. As,tot: Theoretical area of reinforcement required by the design. D: Dead (permanent) load.

  7. Advanced Wall Framing; BTS Technology Fact Sheet

    Energy Technology Data Exchange (ETDEWEB)

    Southface Energy Institute; Tromly, K.

    2000-11-07

    Advanced framing techniques for home construction have been researched extensively and proven effective. Both builders and home owners can benefit from advanced framing. Advanced framing techniques create a structurally sound home that has lower material and labor costs than a conventionally framed house. This fact sheet describes advanced framing techniques, design considerations, and framing.

  8. Model Indepedent Vibration Control

    OpenAIRE

    Yuan, Jing

    2010-01-01

    A NMIFC system is proposed for broadband vibration control. It has two important features. Feature F1 is that the NMIFC is stable without introducing any invasive effects, such as probing signals or controller perturbations, into the vibration system; feature F2 is

  9. Vibration Theory, Vol. 3

    DEFF Research Database (Denmark)

    Nielsen, Søren R. K.

    The present textbook has been written based on previous lecture notes for a course on stochastic vibration theory that is being given on the 9th semester at Aalborg University for M. Sc. students in structural engineering. The present 4th edition of this textbook on linear stochastic vibration...

  10. Vibration Theory, Vol. 3

    DEFF Research Database (Denmark)

    Nielsen, Søren R. K.

    The present textbook has been written based on previous lecture notes for a course on stochastic vibration theory that is being given on the 9th semester at Aalborg University for M. Sc. students in structural engineering. The present 2nd edition of this textbook on linear stochastic vibration...

  11. Hydroelastic Vibrations of Ships

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher; Folsø, Rasmus

    2002-01-01

    A formula for the necessary hull girder bending stiffness required to avoid serious springing vibrations is derived. The expression takes into account the zero crossing period of the waves, the ship speed and main dimensions. For whipping vibrations the probability of exceedance for the combined...

  12. Gearbox vibration diagnostic analyzer

    Science.gov (United States)

    1992-01-01

    This report describes the Gearbox Vibration Diagnostic Analyzer installed in the NASA Lewis Research Center's 500 HP Helicopter Transmission Test Stand to monitor gearbox testing. The vibration of the gearbox is analyzed using diagnostic algorithms to calculate a parameter indicating damaged components.

  13. Mechanical vibration and shock analysis, sinusoidal vibration

    CERN Document Server

    Lalanne, Christian

    2014-01-01

    Everything engineers need to know about mechanical vibration and shock...in one authoritative reference work! This fully updated and revised 3rd edition addresses the entire field of mechanical vibration and shock as one of the most important types of load and stress applied to structures, machines and components in the real world. Examples include everything from the regular and predictable loads applied to turbines, motors or helicopters by the spinning of their constituent parts to the ability of buildings to withstand damage from wind loads or explosions, and the need for cars to m

  14. Emitted vibration measurement device and method

    Science.gov (United States)

    Gisler, G. L.

    1986-10-01

    This invention is directed to a method and apparatus for measuring emitted vibrational forces produced by a reaction wheel assembly due to imbalances, misalignment, bearing defects and the like. The apparatus includes a low mass carriage supported on a large mass base. The carriage is in the form of an octagonal frame having an opening which is adapted for receiving the reaction wheel assembly supported thereon by means of a mounting ring. The carriage is supported on the base by means of air bearings which support the carriage in a generally frictionless manner when supplied with compressed air from a source. A plurality of carriage brackets and a plurality of base blocks provided for physical coupling of the base and carriage. The sensing axes of the load cells are arranged generally parallel to the base and connected between the base and carriage such that all of the vibrational forces emitted by the reaction wheel assembly are effectively transmitted through the sensing axes of the load cells. In this manner, a highly reliable and accurate measurment of the vibrational forces of the reaction wheel assembly can be had. The output signals from the load cells are subjected to a dynamical analyzer which analyzes and identifies the rotor and spin bearing components which are causing the vibrational forces.

  15. Pairs of dual periodic frames

    DEFF Research Database (Denmark)

    Christensen, Ole; Goh, Say Song

    2012-01-01

    is needed. The purpose of the present paper is to provide constructions of dual pairs of frames in the setting of the Hilbert space of periodic functions L2(0,2π). The frames constructed are given explicitly as trigonometric polynomials, which allows for an efficient calculation of the coefficients...

  16. MedlinePlus FAQ: Framing

    Science.gov (United States)

    ... Map FAQs Customer Support Health Topics Drugs & Supplements Videos & Tools Español You Are Here: Home → FAQs → Question URL of this page: https://medlineplus.gov/faq/framing.html I'd like to link to MedlinePlus, but only if I can frame it. Why don't you allow this? To ...

  17. Framing the patent troll debate.

    Science.gov (United States)

    Risch, Michael

    2014-02-01

    The patent troll debate has reached a fevered pitch in the USA. This editorial seeks to frame the debate by pointing out the lack of clarity in defining patent trolls and their allegedly harmful actions. It then frames the debate by asking currently unanswered questions: Where do troll patents come from? What are the effects of troll assertions? Will policy changes improve the system?

  18. Frames, agency and institutional change

    DEFF Research Database (Denmark)

    Rasmussen, Grane Mikael Gregaard; Jensen, Per Langaa; Gottlieb, Stefan Christoffer

    2017-01-01

    This study examines change and the sources influencing the formulation and diffusion of policies in construction. The change examined is the introduction of a benchmarking policy initiative in the Danish construction industry. Using institutional theory with emphasis on the concepts of frames...... and framings, we show how strategically motivated actors are able to frame policy problems in ways that disclose the mixture of motives, interests and institutional mechanisms at play in change processes. In doing so, we contribute to the literature on the role of agency in institutional change and the framing...... of policy problems. We conclude by highlighting how insights gained from the framing perspective present a challenge to the dominant comprehensive rationalist view of the policy process and the formulation and implementation of reform initiatives....

  19. Laryngeal High-Speed Videoendoscopy: Sensitivity of Objective Parameters towards Recording Frame Rate

    Directory of Open Access Journals (Sweden)

    Anne Schützenberger

    2016-01-01

    Full Text Available The current use of laryngeal high-speed videoendoscopy in clinic settings involves subjective visual assessment of vocal fold vibratory characteristics. However, objective quantification of vocal fold vibrations for evidence-based diagnosis and therapy is desired, and objective parameters assessing laryngeal dynamics have therefore been suggested. This study investigated the sensitivity of the objective parameters and their dependence on recording frame rate. A total of 300 endoscopic high-speed videos with recording frame rates between 1000 and 15 000 fps were analyzed for a vocally healthy female subject during sustained phonation. Twenty parameters, representing laryngeal dynamics, were computed. Four different parameter characteristics were found: parameters showing no change with increasing frame rate; parameters changing up to a certain frame rate, but then remaining constant; parameters remaining constant within a particular range of recording frame rates; and parameters changing with nearly every frame rate. The results suggest that (1 parameter values are influenced by recording frame rates and different parameters have varying sensitivities to recording frame rate; (2 normative values should be determined based on recording frame rates; and (3 the typically used recording frame rate of 4000 fps seems to be too low to distinguish accurately certain characteristics of the human phonation process in detail.

  20. Structural Stability and Vibration

    DEFF Research Database (Denmark)

    Wiggers, Sine Leergaard; Pedersen, Pauli

    This book offers an integrated introduction to the topic of stability and vibration. Strikingly, it describes stability as a function of boundary conditions and eigenfrequency as a function of both boundary conditions and column force. Based on a post graduate course held by the author at the Uni......This book offers an integrated introduction to the topic of stability and vibration. Strikingly, it describes stability as a function of boundary conditions and eigenfrequency as a function of both boundary conditions and column force. Based on a post graduate course held by the author...... and their derivation, thus stimulating them to write interactive and dynamic programs to analyze instability and vibrational modes....

  1. Pilot-wave hydrodynamics in a rotating frame: Exotic orbits

    DEFF Research Database (Denmark)

    Oza, Anand U.; Wind-Willassen, Øistein; Harris, Daniel M.

    2014-01-01

    , stable circular orbits give way to wobbling orbits, which are succeeded in turn by instabilities of the orbital center characterized by steady drifting then discrete leaping. In the limit of large vibrational forcing, the walker’s trajectory becomes chaotic, but its statistical behavior reflects......We present the results of a numerical investigation of droplets walking on a rotating vibrating fluid bath. The drop’s trajectory is described by an integro-differential equation, which is simulated numerically in various parameter regimes. As the forcing acceleration is progressively increased...... the influence of the unstable orbital solutions. The study results in a complete regime diagram that summarizes the dependence of the walker’s behavior on the system parameters. Our predictions compare favorably to the experimental observations of Harris and Bush [“Droplets walking in a rotating frame: from...

  2. Serialising languages: Satellite-framed, verb-framed or neither ...

    African Journals Online (AJOL)

    The diversity in the coding of the core schema of motion, i.e., Path, has led to a traditional typology of languages into verb-framed and satellite-framed languages. In the former Path is encoded in verbs and in the latter it is encoded in non-verb elements that function as sisters to co-event expressing verbs such as manner ...

  3. Mediernes framing af Folketingsvalget 2015

    OpenAIRE

    Jyrkinewsky Mathiesen, Marie; Fruergaard, Oliver; Toft-Nielsen, Nina Kristine; Løvstrup Thejls, Michelle; Abild Patrzarlek, Louise

    2015-01-01

    This project will be centered around the media’s framing of the political election in Denmark 2015. More specifically, we will examine how the public service channel DR1 has presented and framed the two political parties Alternativet and Det Kon-servative Folkeparti. Our examination will have its basis in framing theories as pre-sented by Robert Entman and Dietram A. Scheufele and also the theory of Social Constructivism. Through a deductive analysis, we have tried to answer whether DR1,...

  4. Specialized Orthonormal Frames and Embedding

    Directory of Open Access Journals (Sweden)

    Frank B. Estabrook

    2013-02-01

    Full Text Available We discuss some specializations of the frames of flat orthonormal frame bundles over geometries of indefinite signature, and the resulting symmetries of families of embedded Riemannian or pseudo-Riemannian geometries. The specializations are closed sets of linear constraints on the connection 1-forms of the framing. The embeddings can be isometric, as in minimal surfaces or Regge-Teitelboim gravity, or torsion-free, as in Einstein vacuum gravity. Involutive exterior differential systems are given, and their Cartan character tables calculated to express the well-posedness of the underlying partial differential embedding and specialization equations.

  5. Vibration Analysis and the Accelerometer

    Science.gov (United States)

    Hammer, Paul

    2011-01-01

    Have you ever put your hand on an electric motor or motor-driven electric appliance and felt it vibrate? Ever wonder why it vibrates? What is there about the operation of the motor, or the object to which it is attached, that causes the vibrations? Is there anything "regular" about the vibrations, or are they the result of random causes? In this…

  6. Framing of health information messages.

    Science.gov (United States)

    Akl, Elie A; Oxman, Andrew D; Herrin, Jeph; Vist, Gunn E; Terrenato, Irene; Sperati, Francesca; Costiniuk, Cecilia; Blank, Diana; Schünemann, Holger

    2011-12-07

    The same information about the evidence on health effects can be framed either in positive words or in negative words. Some research suggests that positive versus negative framing can lead to different decisions, a phenomenon described as the framing effect. Attribute framing is the positive versus negative description of a specific attribute of a single item or a state, for example, "the chance of survival with cancer is 2/3" versus "the chance of mortality with cancer is 1/3". Goal framing is the description of the consequences of performing or not performing an act as a gain versus a loss, for example, "if you undergo a screening test for cancer, your survival will be prolonged" versus "if you don't undergo screening test for cancer, your survival will be shortened". To evaluate the effects of attribute (positive versus negative) framing and of goal (gain versus loss) framing of the same health information, on understanding, perception of effectiveness, persuasiveness, and behavior of health professionals, policy makers, and consumers. We searched the Cochrane Central Register of Controlled Trials (CENTRAL, The Cochrane Library, issue 3 2007), MEDLINE (Ovid) (1966 to October 2007), EMBASE (Ovid) (1980 to October 2007), PsycINFO (Ovid) (1887 to October 2007). There were no language restrictions. We reviewed the reference lists of related systematic reviews, included studies and of excluded but closely related studies. We also contacted experts in the field. We included randomized controlled trials, quasi-randomised controlled trials, and cross-over studies with health professionals, policy makers, and consumers evaluating one of the two types of framing. Two review authors extracted data in duplicate and independently. We graded the quality of evidence for each outcome using the GRADE approach. We standardized the outcome effects using standardized mean difference (SMD). We stratified the analysis by the type of framing (attribute, goal) and conducted pre

  7. Vibrations and Stability

    DEFF Research Database (Denmark)

    Thomsen, Jon Juel

    About this textbook An ideal text for students that ties together classical and modern topics of advanced vibration analysis in an interesting and lucid manner. It provides students with a background in elementary vibrations with the tools necessary for understanding and analyzing more complex...... dynamical phenomena that can be encountered in engineering and scientific practice. It progresses steadily from linear vibration theory over various levels of nonlinearity to bifurcation analysis, global dynamics and chaotic vibrations. It trains the student to analyze simple models, recognize nonlinear...... phenomena and work with advanced tools such as perturbation analysis and bifurcation analysis. Explaining theory in terms of relevant examples from real systems, this book is user-friendly and meets the increasing interest in non-linear dynamics in mechanical/structural engineering and applied mathematics...

  8. Reference frame for Product Configuration

    DEFF Research Database (Denmark)

    Ladeby, Klaes Rohde; Oddsson, Gudmundur Valur

    2011-01-01

    on configuration systems in the shape of anecdotal reporting on the development of information systems that perhaps support the configuration task – perhaps not. Consequently, the definition of configuration has become ambiguous as different research groups defines configuration differently. This paper propose......This paper presents a reference frame for configuration. The reference frame is established by review of existing literature, and consequently it is a theoretical frame of reference. The review of literature shows a deterioration of the understanding of configuration. Most recent literature reports...... a reference frame for configuration that permits 1) a more precise understanding of a configuration system, 2) a understanding of how the configuration system relate to other systems, and 3) a definition of the basic concepts in configuration. The total configuration system, together with the definition...

  9. Putting Safety in the Frame

    Directory of Open Access Journals (Sweden)

    Valerie Jean O’Keeffe

    2015-06-01

    Full Text Available Current patient safety policy focuses nursing on patient care goals, often overriding nurses’ safety. Without understanding how nurses construct work health and safety (WHS, patient and nurse safety cannot be reconciled. Using ethnography, we examine social contexts of safety, studying 72 nurses across five Australian hospitals making decisions during patient encounters. In enacting safe practice, nurses used “frames” built from their contextual experiences to guide their behavior. Frames are produced by nurses, and they structure how nurses make sense of their work. Using thematic analysis, we identify four frames that inform nurses’ decisions about WHS: (a communicating builds knowledge, (b experiencing situations guides decisions, (c adapting procedures streamlines work, and (d team working promotes safe working. Nurses’ frames question current policy and practice by challenging how nurses’ safety is positioned relative to patient safety. Recognizing these frames can assist the design and implementation of effective WHS management.

  10. Willpower depletion and framing effects

    OpenAIRE

    de Haan, Thomas; van Veldhuizen, Roel

    2013-01-01

    We investigate whether depleting people's cognitive resources (or willpower) affects the degree to which they are susceptible to framing effects. Recent research in social psychology and economics has suggested that willpower is a resource that can be temporarily depleted and that a depleted level of willpower is associated with self-control problems in a variety of contexts. In this study, we extend the willpower depletion paradigm to framing effects and argue that willpower depletion should...

  11. Frames and extension problems II

    DEFF Research Database (Denmark)

    Christensen, Ole; Kim, Hong Oh; Kim, Rae Young

    2014-01-01

    This article is a follow-up on the article Frames and Extension Problems I. Here we will go into more recent progress on the topic and also present some open problems.......This article is a follow-up on the article Frames and Extension Problems I. Here we will go into more recent progress on the topic and also present some open problems....

  12. Evaluation of hand-arm and whole-body vibrations in construction and property management.

    Science.gov (United States)

    Coggins, Marie A; Van Lente, Eric; McCallig, Margaret; Paddan, Gurmail; Moore, Ken

    2010-11-01

    To identify and measure the magnitude of hand-arm vibration (HAV) and whole-body vibration (WBV) sources (tools, vehicles etc.) in use within a previously unexamined sector: a construction and property management company. To evaluate the effect of factors such as age of tool, materials being worked on, number and location of tool handles, tool weight, and manufacturer brand on HAV magnitude and the effect of factors such as manufacturer machine brand, terrain, and work task on WBV magnitude. This study was carried out in a construction and property management company, employees (n = 469) working in the engineering services and maintenance departments who use vibrating equipment as part of their work were invited to participate. Two hundred and eighty-nine employees working as general operatives, excavator drivers, stone masons, carpenters, labourers, fitters, welders, and gardeners agreed to participate. A total of 20 types of hand tool (n = 264) and 11 types of vehicle (n = 158) in use within the company were selected for inclusion in the study. Five pieces of equipment had never previously been measured. Vibration measurements were carried out in accordance with ISO 5349-1 (Mechanical vibration-measurement and assessment of human exposure to hand transmitted vibration-Part 1: general guidance. 2001) (HAV) and ISO 2631-1 (Mechanical vibration and shock: evaluation of human exposure to WBV in the working environment. Part 1-general requirements. 1997) (WBV). Vibration measurements were made while workers were operating the equipment as part of their normal work activities. A wide range of vibration emission values were recorded for most tool types, e.g. orbital sanders (1.39-10.90 m s⁻²) and angle grinders (0.28-12.25 m s⁻²), and vehicle, e.g. forklifts (0.41-1.00 m s⁻²) and tractors (0.04-0.42 m s⁻²). Vibration magnitudes were largely consistent with those found in previous studies. The highest HAV magnitude was measured on a demolition hammer (13.3 m

  13. Frame by frame analysis of glottic insufficiency using laryngovideostroboscopy.

    Science.gov (United States)

    Carroll, Thomas L; Wu, Yi-Hsuan E; McRay, Marissa; Gherson, Shirley

    2012-03-01

    Glottic insufficiency (GI) can be either grossly obvious or subtle in its presentation. Subtle GI is demonstrated by various Laryngovideostroboscopic (LVS) clues, including complete but "short" phase closure of the true vocal folds (VFs) during the glottic cycle. We used the frame by frame analysis (FBFA) technique to evaluate its effectiveness in objectively contributing to the diagnosis of subtle GI in patients with atrophic and/or paretic VFs. This article intends to formally present the methods and intentions of the FBFA technique and report our findings using FBFA on subjects with clinically diagnosed GI and normal volunteers. Retrospective review and demonstration of technique. Forty-four subjects with a prior clinical diagnosis of true VF atrophy (25/44) and/or paresis (19/44) and five normal volunteers were identified. Using the FBFA technique, each subject's average percentage of closed frames per glottic cycle was recorded. Subjects with atrophy spent 32.4% of the frames of the glottic cycle in the closed phase, subjects with paresis spent 35.7% of the frames closed, and normal subjects spent 50.2% of the frames closed. FBFA appears to be a simple objective method for the novice or experienced LVS interpreter, by which one can suspect subtle GI. Because of the inherent physical properties by which LVS gives an "illusionary" representation of the glottic cycle, the FBFA technique remains a theoretical tool. Future studies using high-speed digital imaging are needed to validate this useful technique. Copyright © 2012 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

  14. f3: Full Frame Fotometry for Kepler Full Frame Images

    Science.gov (United States)

    Montet, Benjamin T.

    2017-05-01

    Light curves from the Kepler telescope rely on "postage stamp" cutouts of a few pixels near each of 200,000 target stars. These light curves are optimized for the detection of short-term signals like planet transits but induce systematics that overwhelm long-term variations in stellar flux. Longer-term effects can be recovered through analysis of the Full Frame Images, a set of calibration data obtained monthly during the Kepler mission. The Python package f3 analyzes the Full Frame Images to infer long-term astrophysical variations in the brightness of Kepler targets, such as magnetic activity or sunspots on slowly rotating stars.

  15. Tennis Racket Vibrations and Shock Transmission to the Wrist during Forehand Drive.

    Science.gov (United States)

    Rogowski, Isabelle; Creveaux, Thomas; Triquigneaux, Sylvain; Macé, Pierre; Gauthier, Fabien; Sevrez, Violaine

    2015-01-01

    This study aimed to investigate the effects of two different racket models and two different forehand drive velocities on the three-dimensional vibration behavior of the racket and shock transmission to the player's wrist under real playing conditions. Nine tennis players performed a series of crosscourt flat forehand drives at two velocities, using a lightly and a highly vibrant racket. Two accelerometers were fixed on the racket frame and the player's wrist. The analysis of vibration signals in both time and frequency domains showed no interaction effect of velocity and racket conditions either on the racket vibration behavior or on shock transmission. An increase in playing velocity enlarged the amount of vibrations at the racket and wrist, but weakly altered their frequency content. As compared to a racket perceived as highly vibrating, a racket perceived as lightly vibrating damped longer in the out-of-plane axis of the racket and shorter on the other axis of the racket and on the wrist, and displayed a lower amount of energy in the high frequency of the vibration signal at the racket and wrist. These findings indicated that the playing velocity must be controlled when investigating the vibration loads due to the racket under real playing conditions. Similarly, a reduced perception of vibration by the tennis player would be linked to decreased amplitude of the racket vibration signal, which may concentrate the signal energy in the low frequencies.

  16. Frames of exponentials:lower frame bounds for finite subfamilies, and approximation of the inverse frame operator

    DEFF Research Database (Denmark)

    Christensen, Ole; Lindner, Alexander M

    2001-01-01

    We give lower frame bounds for finite subfamilies of a frame of exponentials {e(i lambdak(.))}k is an element ofZ in L-2(-pi,pi). We also present a method for approximation of the inverse frame operator corresponding to {e(i lambdak(.))}k is an element ofZ, where knowledge of the frame bounds for...

  17. Another frame, another game? : Explaining framing effects in economic games

    NARCIS (Netherlands)

    Gerlach, Philipp; Jaeger, B.; Hopfensitz, A.; Lori, E.

    2016-01-01

    Small changes in the framing of games (i.e., the way in which the game situation is described to participants) can have large effects on players' choices. For example, referring to a prisoner's dilemma game as the "Community Game" as opposed to the "Wall Street Game" can double the cooperation rate

  18. Vibrational spectroscopy of resveratrol

    Science.gov (United States)

    Billes, Ferenc; Mohammed-Ziegler, Ildikó; Mikosch, Hans; Tyihák, Ernő

    2007-11-01

    In this article the authors deal with the experimental and theoretical interpretation of the vibrational spectra of trans-resveratrol (3,5,4'-trihydroxy- trans-stilbene) of diverse beneficial biological activity. Infrared and Raman spectra of the compound were recorded; density functional calculations were carried out resulting in the optimized geometry and several properties of the molecule. Based on the calculated force constants, a normal coordinate analysis yielded the character of the vibrational modes and the assignment of the measured spectral bands.

  19. Bumblebee vibration activated foraging

    OpenAIRE

    Su, Dan Kuan-Nien

    2009-01-01

    The ability use vibrational signals to activate nestmate foraging is found in the highly social bees, stingless bees and honey bees, and has been hypothesized to exist in the closely related, primitively eusocial bumble bees. We provide the first strong and direct evidence that this is correct. Inside the nest, bumble bee foragers produce brief bursts of vibration (foraging activation pulses) at 594.5 Hz for 63±26 ms (velocityRMS=0.46±0.02mm/s, forceRMS=0.8±0.2 mN. Production of these vibrati...

  20. Man-Induced Vibrations

    DEFF Research Database (Denmark)

    Jönsson, Jeppe; Hansen, Lars Pilegaard

    1994-01-01

    concerned with spectator-induced vertical vibrations on grandstands. The idea is to use impulse response analysis and base the load description on the load impulse. If the method is feasable, it could be used in connection with the formulation of requirements in building codes. During the last two decades...... work has been done on the measurement of the exact load functions and related reponse analysis. A recent work using a spectral description has been performed by Per-Erik Erikson and includes a good literature survey. Bachmann and Ammann give a good overview of vibrations caused by human activity. Other...

  1. Vibrations and waves

    CERN Document Server

    Kaliski, S

    2013-01-01

    This book gives a comprehensive overview of wave phenomena in different media with interacting mechanical, electromagnetic and other fields. Equations describing wave propagation in linear and non-linear elastic media are followed by equations of rheological models, models with internal rotational degrees of freedom and non-local interactions. Equations for coupled fields: thermal, elastic, electromagnetic, piezoelectric, and magneto-spin with adequate boundary conditions are also included. Together with its companion volume Vibrations and Waves. Part A: Vibrations this work provides a wealth

  2. Heterogeneous Dynamics of Coupled Vibrations

    NARCIS (Netherlands)

    Cringus, Dan; Jansen, Thomas I. C.; Pshenichnikov, Maxim S.; Schoenlein, RW; Corkum, P; DeSilvestri, S; Nelson, KA; Riedle, E

    2009-01-01

    Frequency-dependent dynamics of coupled stretch vibrations of a water molecule are revealed by 2D IR correlation spectroscopy. These are caused by non-Gaussian fluctuations of the environment around the individual OH stretch vibrations.

  3. Examining the Linkage Between FRAMES and GMS

    Energy Technology Data Exchange (ETDEWEB)

    Whelan, Gene; Castleton, Karl J.

    2006-02-13

    Because GMS provides so many features, of which some are also addressed by FRAMES, it could represent a platform to link to FRAMES, or FRAMES could represent a platform to link to GMS. The focus of this summary is to examine the strengths and weaknesses of the potential linkage direction and provide recommendations for the linkage between FRAMES and GMS.

  4. Frame Rate and Human Vision

    Science.gov (United States)

    Watson, Andrew B.

    2012-01-01

    To enhance the quality of the theatre experience, the film industry is interested in achieving higher frame rates for capture and display. In this talk I will describe the basic spatio-temporal sensitivities of human vision, and how they respond to the time sequence of static images that is fundamental to cinematic presentation.

  5. News framing effects and emotions

    NARCIS (Netherlands)

    Schuck, A.R.T.; Feinholdt, A.; Scott, R.A.; Kosslyn, S.M.

    2015-01-01

    Framing research is thriving and has become ever more popular among researchers and students alike. This essay reviews some of the latest trends and developments in the field, explains key terms and concepts, identifies likely future research lines, and zooms in on one of these in particular, that

  6. Cooperation preferences and framing effects

    NARCIS (Netherlands)

    Petit Dit Dariel, A.C.

    2013-01-01

    This paper presents the results from an experiment investigating whether framing affects the elicitation and predictive power of preferences for cooperation, i.e., the willingness to cooperate with others. Cooperation preferences are elicited in three treatments using the method of Fischbacher,

  7. Media framing and social movements

    NARCIS (Netherlands)

    Vliegenthart, R.; Snow, D.A.; Della Porta, D.; Klandermans, B.; McAdam, D.

    2013-01-01

    In their study of media content, mass communication scholars commonly rely on Entman's (1993: 52) definition of framing: "[selecting] some aspects of a perceived reality and make them more salient in a communicating text, in such a way as to promote a particular problem definition, causal

  8. Meta framing and polyphonic structures

    DEFF Research Database (Denmark)

    Pedersen, Karsten

    2017-01-01

    in various ways in BT’s 2012 coverage of a doping case involving Riis. In this article I investigate the way in which BT meta frames itself and its own actions in order to show and underline the seriousness with which BT treats sports journalism. The study is part of a recurring Danish project harvesting...

  9. Framing the future of fracking

    NARCIS (Netherlands)

    Metze, Tamara

    2017-01-01

    Hydraulic fracturing is a technology developed to improve and increase the production of natural gas. In many countries, including the Netherlands, it has caused environmental controversies. In these controversies, 'futurity framing' may open up debates for alternative paradigms such as

  10. G-frames with bounded linear operators

    OpenAIRE

    Xiao, Xiang-chun; Zhu, Yu-can; Shu, Zhi-biao; Ding, Ming-ling

    2015-01-01

    In this paper, we introduce the more general g-frame which is called a $K$-g-frame by combining a g-frame with a bounded linear operator $K$ in a Hilbert space. We give several equivalent characterizations for $K$-g-frames and discuss the stability of perturbation for $K$-g-frames. We also investigate the relationship between a $K$-g-frame and the range of the bounded linear operator $K$. In the end, we give two sufficient conditions for the remainder of a $K$-g-frame after an erasure to stil...

  11. Development of an experimental methodology to evaluate the influence of a bamboo frame on the bicycle ride comfort

    Science.gov (United States)

    Thite, A. N.; Gerguri, S.; Coleman, F.; Doody, M.; Fisher, N.

    2013-09-01

    In the current environment of increased emphasis on sustainable transport, there is manifold increase in the use of bicycles for urban transport. One concern which might restrict the use is the ride comfort and fatigue. There has been limited research in addressing the difficulty in bicycle ride comfort quantification. The current study aims to develop a methodology to quantify bicycle discomfort so that performance of bicycles constructed from bamboo and aluminium alloy can be compared. Experimentally obtained frequency response functions are used to establish a relation between the road input and the seat and rider response. A bicycle track input profile based on standard road profiles is created so as to estimate the acceleration responses. The whole-body-vibration frequency weighting is applied to quantify the perception of vibration intensity so that eventual discomfort ranking can be obtained. The measured frequency response functions provide an insight into the effect of frame dynamics on the overall resonant behaviour of the bicycles. The beneficial effect of frame compliance and damping on lower modes of vibration is very clear in the case of bamboo frame, in turn affecting seat and rider response. In the bamboo frame, because of multiple resonances, the frequency response of the handlebar is smaller at higher frequencies suggesting effective isolation. Further improvements may have come from the joints made from natural composites. Overall, based on the comparative analysis and the methodology developed, bamboo frame shows significant improvement in ride comfort performance compared with the aluminium frame.

  12. High-frame-rate echocardiography with reduced sidelobe level.

    Science.gov (United States)

    Hasegawa, Hideyuki; Kanai, Hiroshi

    2012-11-01

    Echocardiography has become an indispensable modality for diagnosis of the heart. It enables observation of the shape of the heart and estimation of global heart function based on B-mode and M-mode imaging. Methods for echocardiographic estimation of myocardial strain and strain rate have also been developed to evaluate regional heart function. Furthermore, it has been recently shown that echocardiographic measurements of transmural transition of myocardial contraction/relaxation and propagation of vibration caused by closure of the heart valve would be useful for evaluation of myocardial function and viscoelasticity. However, such measurements require a frame rate (typically >200 Hz) much higher than that achieved by conventional ultrasonic diagnostic equipment. We have recently realized a high frame rate of about 300 Hz with a full field of view of 90° using diverging transmit beams and parallel receive beamforming. Although high-frame-rate imaging was made possible by this method, the side lobe level was slightly larger than that of the conventional method. To reduce the side lobe level, phase coherence imaging has recently been developed. Using this method, the spatial resolution is improved and the side lobe level is also reduced. However, speckle-like echoes, for example, echoes from the inside of the heart wall, are also suppressed. In the present study, a method for reducing the side lobe level while preserving speckle-like echoes was developed. The side lobe level was evaluated using a wire phantom. The side lobe level of the high-frame-rate imaging using unfocused diverging beams was improved by 13.3 dB by the proposed method. In in vivo measurements, a B-mode image of the heart of a 23-year-old healthy male could be obtained while preserving the speckle pattern in the heart wall at a frame rate of 316 Hz with a full field of view of 90°.

  13. Frames and generalized shift-invariant systems

    DEFF Research Database (Denmark)

    Christensen, Ole

    2004-01-01

    With motivation from the theory of Hilbert-Schmidt operators we review recent topics concerning frames in L 2 (R) and their duals. Frames are generalizations of orthonormal bases in Hilbert spaces. As for an orthonormal basis, a frame allows each element in the underlying Hilbert space...... to be written as an unconditionally convergent infinite linear combination of the frame elements; however, in contrast to the situation for a basis, the coefficients might not be unique. We present the basic facts from frame theory and the motivation for the fact that most recent research concentrates on tight...... frames or dual frame pairs rather than general frames and their canonical dual. The corresponding results for Gabor frames and wavelet frames are discussed in detail....

  14. Composite Struts Would Damp Vibrations

    Science.gov (United States)

    Dolgin, Benjamin P.

    1991-01-01

    New design of composite-material (fiber/matrix laminate) struts increases damping of longitudinal vibrations without decreasing longitudinal stiffness or increasing weight significantly. Plies with opposing chevron patterns of fibers convert longitudinal vibrational stresses into shear stresses in intermediate viscoelastic layer, which dissipate vibrational energy. Composite strut stronger than aluminum strut of same weight and stiffness.

  15. Frame covariant nonminimal multifield inflation

    Science.gov (United States)

    Karamitsos, Sotirios; Pilaftsis, Apostolos

    2018-02-01

    We introduce a frame-covariant formalism for inflation of scalar-curvature theories by adopting a differential geometric approach which treats the scalar fields as coordinates living on a field-space manifold. This ensures that our description of inflation is both conformally and reparameterization covariant. Our formulation gives rise to extensions of the usual Hubble and potential slow-roll parameters to generalized fully frame-covariant forms, which allow us to provide manifestly frame-invariant predictions for cosmological observables, such as the tensor-to-scalar ratio r, the spectral indices nR and nT, their runnings αR and αT, the non-Gaussianity parameter fNL, and the isocurvature fraction βiso. We examine the role of the field space curvature in the generation and transfer of isocurvature modes, and we investigate the effect of boundary conditions for the scalar fields at the end of inflation on the observable inflationary quantities. We explore the stability of the trajectories with respect to the boundary conditions by using a suitable sensitivity parameter. To illustrate our approach, we first analyze a simple minimal two-field scenario before studying a more realistic nonminimal model inspired by Higgs inflation. We find that isocurvature effects are greatly enhanced in the latter scenario and must be taken into account for certain values in the parameter space such that the model is properly normalized to the observed scalar power spectrum PR. Finally, we outline how our frame-covariant approach may be extended beyond the tree-level approximation through the Vilkovisky-De Witt formalism, which we generalize to take into account conformal transformations, thereby leading to a fully frame-invariant effective action at the one-loop level.

  16. Frame covariant nonminimal multifield inflation

    Directory of Open Access Journals (Sweden)

    Sotirios Karamitsos

    2018-02-01

    Full Text Available We introduce a frame-covariant formalism for inflation of scalar-curvature theories by adopting a differential geometric approach which treats the scalar fields as coordinates living on a field-space manifold. This ensures that our description of inflation is both conformally and reparameterization covariant. Our formulation gives rise to extensions of the usual Hubble and potential slow-roll parameters to generalized fully frame-covariant forms, which allow us to provide manifestly frame-invariant predictions for cosmological observables, such as the tensor-to-scalar ratio r, the spectral indices nR and nT, their runnings αR and αT, the non-Gaussianity parameter fNL, and the isocurvature fraction βiso. We examine the role of the field space curvature in the generation and transfer of isocurvature modes, and we investigate the effect of boundary conditions for the scalar fields at the end of inflation on the observable inflationary quantities. We explore the stability of the trajectories with respect to the boundary conditions by using a suitable sensitivity parameter. To illustrate our approach, we first analyze a simple minimal two-field scenario before studying a more realistic nonminimal model inspired by Higgs inflation. We find that isocurvature effects are greatly enhanced in the latter scenario and must be taken into account for certain values in the parameter space such that the model is properly normalized to the observed scalar power spectrum PR. Finally, we outline how our frame-covariant approach may be extended beyond the tree-level approximation through the Vilkovisky–De Witt formalism, which we generalize to take into account conformal transformations, thereby leading to a fully frame-invariant effective action at the one-loop level.

  17. Ship Vibration Design Guide

    Science.gov (United States)

    1989-07-01

    Frachtschiffen," Werft Reederie Hafen, 1925. 4-21 Noonan, E. F. "Vibration Considerations for 120,000 CM LNG Ships," NKF: Preliminary Report No. 7107, 25...Ship Response to Ice - A Second Season by C. Daley, J. W. St. John, R. Brown, J. Meyer , and I. Glen 1990 SSC-340 Ice Forces and Ship Response to Ice

  18. Compact Vibration Damper

    Science.gov (United States)

    Ivanco, Thomas G. (Inventor)

    2014-01-01

    A vibration damper includes a rigid base with a mass coupled thereto for linear movement thereon. Springs coupled to the mass compress in response to the linear movement along either of two opposing directions. A converter coupled to the mass converts the linear movement to a corresponding rotational movement. A rotary damper coupled to the converter damps the rotational movement.

  19. Vibrations and Eigenvalues

    Indian Academy of Sciences (India)

    The vibrating string problem is the source of much mathematicsand physics. This article describes Lagrange's formulationof a discretised version of the problem and its solution.This is also the first instance of an eigenvalue problem. Author Affiliations. Rajendra Bhatia1. Ashoka University, Rai, Haryana 131 029, India.

  20. Blade Vibration Measurement System

    Science.gov (United States)

    Platt, Michael J.

    2014-01-01

    The Phase I project successfully demonstrated that an advanced noncontacting stress measurement system (NSMS) could improve classification of blade vibration response in terms of mistuning and closely spaced modes. The Phase II work confirmed the microwave sensor design process, modified the sensor so it is compatible as an upgrade to existing NSMS, and improved and finalized the NSMS software. The result will be stand-alone radar/tip timing radar signal conditioning for current conventional NSMS users (as an upgrade) and new users. The hybrid system will use frequency data and relative mode vibration levels from the radar sensor to provide substantially superior capabilities over current blade-vibration measurement technology. This frequency data, coupled with a reduced number of tip timing probes, will result in a system capable of detecting complex blade vibrations that would confound traditional NSMS systems. The hardware and software package was validated on a compressor rig at Mechanical Solutions, Inc. (MSI). Finally, the hybrid radar/tip timing NSMS software package and associated sensor hardware will be installed for use in the NASA Glenn spin pit test facility.

  1. Vibration Sensitive Keystroke Analysis

    NARCIS (Netherlands)

    Lopatka, M.; Peetz, M.-H.; van Erp, M.; Stehouwer, H.; van Zaanen, M.

    2009-01-01

    We present a novel method for performing non-invasive biometric analysis on habitual keystroke patterns using a vibration-based feature space. With the increasing availability of 3-D accelerometer chips in laptop computers, conventional methods using time vectors may be augmented using a distinct

  2. Fight or flight: Affective news framing effects

    OpenAIRE

    Feinholdt, A.

    2016-01-01

    This dissertation investigates how emotions shape and are shaped by news framing and how this interplay leads to a number of affective news framing effects. My work reveals that emotions do not only function as mechanisms but also as channels strengthening or weakening framing effects. In addition, I show that issue characteristics and the selected news frame can determine whether and how emotions are elicited. Further, I provide evidence that affective news framing effects can arise as the r...

  3. A self-adaptive anti-vibration pipeline-filtering algorithm

    Science.gov (United States)

    Wu, Houde; Wang, Bin; Zhao, Ming; Xu, Wenhai

    2015-03-01

    The mobile pipeline-filtering algorithm is a real-time algorithm that performs well in detecting small dim targets, but it is particularly sensitive to interframe vibration of sequence images. When searching for small dim targets at sea based on an infrared imaging system, irregular and random vibration of the airborne imaging platform causes huge interference problems for the mobile pipeline-filtering. This paper puts forward a pipeline-filtering algorithm that has a good performance on self-adaptive anti-vibration. In the block matching method using the normalized cross-correlations coefficient (NCC), the interframe vibration of sequence images is acquired in real time and used to correct coordinates of the single-frame detection results, and then the corrected detection results are used to complete the mobile pipelinefiltering. Experimental results show that the algorithm can overcome the problem of interframe vibration of sequence images, thus realizing accurate detection of small dim maritime targets.

  4. Ultrasonic-impact grinder system

    Science.gov (United States)

    Calkins, N.C.

    1982-09-30

    The disclosure relates to an ultrasonic impact grinding apparatus utilizing a counterweight to set an unloaded friction free condition. An added weight is used to optimize feed rate in accordance with the material to be cut, tool size and the like.

  5. Miniature grinder for solid specimens

    Science.gov (United States)

    Houser, C. P.; Pesch, W. A.

    1971-01-01

    Machine grinds fines to appropriate micron sizes with the least biological trauma and greatest degree of reproducibility. Device controls destruction of material so that recovery of microorganisms is as great as possible and protects operation and grinding products from exogenous contamination.

  6. [Dental implants in tooth grinders].

    Science.gov (United States)

    Lobbezoo, F; Brouwers, J E; Cune, M S; Naeije, M

    2004-03-01

    Bruxism (tooth grinding and clenching) is generally considered a contraindication for dental implants, although the evidence is usually based on clinical experience only. So far, studies to the possible cause-and-effect relationship between bruxism and implant failure do not yield consistent and specific outcomes. This is partly due to the large variation in the technical and the biological aspects of the investigations. Although there is still no proof that bruxism causes overload of dental implants and their suprastructures, a careful approach is recommended. Practical advices as to minimize the chance of implant failure are given. Besides the recommendation to reduce or eliminate bruxism itself, these advices concern the number and dimensions of the implants, the design of the occlusion and articulation patterns, and the use of a hard nightguard.

  7. PAIR FRAMES IN HILBERT C∗−MODULES 1. Introduction Frames ...

    Indian Academy of Sciences (India)

    53

    results obtained for Bessel multipliers in Hilbert C∗−modules to pair frames and considering the stability of pair frames under invertible operators, we construct new pair frames and we show that pair frames are stable under small perturbations. 1. Introduction. Frames for Hilbert spaces were first introduced by Duffin and ...

  8. Investigating the Improved Aerodynamic Efficiency of Cambered Frames on Membrane MAV Wings

    Science.gov (United States)

    Wrist, Andrew; Zhang, Zheng; Hubner, Paul

    2014-11-01

    Previous research has demonstrated that membrane wings with cambered frames are more aerodynamically efficient than those with flat frames, despite passive dynamic membrane cambering for both. To help understand this aerodynamic benefit, this study compares the time-averaged membrane shape as well as membrane vibration frequency and amplitude for a group of wings with cambered frames. The frames were 3D printed with a hardened polymer material, and a silicon rubber membrane was attached to the top surface. The frame aspect ratio is two, comprised of two cells each with a cell aspect ratio of one. The rigid leading edge extended 20% of the chord, and the trailing edge was scalloped at 25%. Camber ranged from 2--6%, camber location from 40--60%, and airfoil thickness from 4--6%. Tests were performed in the University of Alabama's MAV wind tunnel at 10 m/s (Re = 50,000). High speed imaging results of the deformation and vibration will be discussed in context to airfoil and wing theory. National Science Foundation Grant Number: 1358991.

  9. Animal Communications Through Seismic Vibrations

    Energy Technology Data Exchange (ETDEWEB)

    Hill, Peggy (University of Tulsa)

    2001-05-02

    Substrate vibration has been important to animals as a channel of communication for millions of years, but our literature on vibration in this context of biologically relevant information is only decades old. The jaw mechanism of the earliest land vertebrates allowed them to perceive substrate vibrations as their heads lay on the ground long before airborne sounds could be heard. Although the exact mechanism of vibration production and the precise nature of the wave produced are not always understood, recent development of affordable instrumentation to detect and measure vibrations has allowed researchers to answer increasingly sophisticated questions about how animals send and receive vibration signals. We now know that vibration provides information used in predator defense, prey detection, recruitment to food, mate choice, intrasexual competition, and maternal/brood social interactions in a variety of insect orders, spiders, crabs, scorpions, chameleons, frogs, golden moles, mole rats, kangaroos rats, wallabies, elephants and bison.

  10. Sparsity and spectral properties of dual frames

    DEFF Research Database (Denmark)

    Krahmer, Felix; Kutyniok, Gitta; Lemvig, Jakob

    2013-01-01

    We study sparsity and spectral properties of dual frames of a given finite frame. We show that any finite frame has a dual with no more than $n^2$ non-vanishing entries, where $n$ denotes the ambient dimension, and that for most frames no sparser dual is possible. Moreover, we derive an expression...... for the exact sparsity level of the sparsest dual for any given finite frame using a generalized notion of spark. We then study the spectral properties of dual frames in terms of singular values of the synthesis operator. We provide a complete characterization for which spectral patterns of dual frames...... are possible for a fixed frame. For many cases, we provide simple explicit constructions for dual frames with a given spectrum, in particular, if the constraint on the dual is that it be tight....

  11. Variance based OFDM frame synchronization

    Directory of Open Access Journals (Sweden)

    Z. Fedra

    2012-04-01

    Full Text Available The paper deals with a new frame synchronization scheme for OFDM systems and calculates the complexity of this scheme. The scheme is based on the computing of the detection window variance. The variance is computed in two delayed times, so a modified Early-Late loop is used for the frame position detection. The proposed algorithm deals with different variants of OFDM parameters including guard interval, cyclic prefix, and has good properties regarding the choice of the algorithm's parameters since the parameters may be chosen within a wide range without having a high influence on system performance. The verification of the proposed algorithm functionality has been performed on a development environment using universal software radio peripheral (USRP hardware.

  12. Hierarchical classification as relational framing.

    Science.gov (United States)

    Slattery, Brian; Stewart, Ian

    2014-01-01

    The purpose of this study was to model hierarchical classification as contextually controlled, generalized relational responding or relational framing. In Experiment 1, a training procedure involving nonarbitrarily related multidimensional stimuli was used to establish two arbitrary shapes as contextual cues for 'member of' and 'includes' relational responding, respectively. Subsequently those cues were used to establish a network of arbitrary stimuli in particular hierarchical relations with each other, and then test for derivation of further untrained hierarchical relations as well as for transformation of functions. Resultant patterns of relational framing showed properties of transitive class containment, asymmetrical class containment, and unilateral property induction, consistent with conceptions of hierarchical classification as described within the cognitive developmental literature. Experiment 2 extended the basic model by using "fuzzy category" stimuli and providing a better controlled test of transformation of functions. Limitations and future research directions are discussed. © Society for the Experimental Analysis of Behavior.

  13. Framing Analysis of Kosovo Independence

    OpenAIRE

    Maiorescu, Roxana

    2009-01-01

    On February 17, 2008 Kosovo declared its independence from Serbia and the event spurred significant media attention. Countries like Spain, Romania, and Russia feared that the event would engender separatism on their own territories, while the U.S., Germany, France, Italy, and UK regarded it as a democratic step. This thesis uses the framing theory to content analyze newspaper articles in seven languages (N=191) that appeared between November 17, 2007 and May 17, 2008, three months before and ...

  14. Predicting the Strength of Online News Frames

    Directory of Open Access Journals (Sweden)

    Hrvoje Jakopović

    2017-10-01

    Full Text Available Framing theory is one of the most significant approaches to understanding media and their potential impact on publics. Leaving aside that fact, the author finds that publicity effects seem to be dispersed and difficult to catch for public relations. This article employs a specific research design, which could be applied to public relations practice, namely with a view to observing correlations between specific media frames and individual frames. The approach is based on the typology of news frames. The author attributes negative, positive and neutral determinants to the types of frames in his empirical research. Online news regarding three transport organizations and the accompanying user comments (identified as negative, positive and neutral are analysed by means of the method of content and sentiment analysis. The author recognizes user comments and reviews as individual frames that take part in the creation of online image. Furthermore, he identifies the types of media frames as well as individual frames manifested as image, and undertakes correlation research in order to establish their prediction potential. The results expose the most frequently used types of media frames concerning the transport domain. The media are keen to report through the attribution of responsibility frame, and after that, through the economic frame and the conflict frame, but, on the other hand, they tend to neglect the human interest frame and the morality frame. The results show that specific types of news frames enable better prediction of user reactions. The economic frame and the human interest frame therefore represent the most predictable types of frame.

  15. Vibration Attenuation of Plate Using Multiple Vibration Absorbers

    Directory of Open Access Journals (Sweden)

    Zaman Izzuddin

    2014-07-01

    Full Text Available Vibrations are undesired phenomenon and it can cause harm, distress and unsettling influence to the systems or structures, for example, aircraft, automobile, machinery and building. One of the approach to limit this vibration by introducing passive vibration absorber attached to the structure. In this paper, the adequacy of utilizing passive vibration absorbers are investigated. The vibration absorber system is designed to minimize the vibration of a thin plate fixed along edges. The plate’s vibration characteristics, such as, natural frequency and mode shape are determined using three techniques: theoretical equations, finite element (FE analysis and experiment. The results demonstrate that the first four natural frequencies of fixed-fixed ends plate are 48, 121, 193 and 242 Hz, and these results are corroborated well with theoretical, FE simulation and experiment. The experiment work is further carried out with attached single and multiple vibration absorbers onto plate by tuning the absorber’s frequency to match with the excitation frequency. The outcomes depict that multiple vibration absorbers are more viable in lessening the global structural vibration.

  16. Good vibrations. [Hydraulic turbines

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, P.

    1994-07-01

    The latest developments in the Voith Turbine Control and Automation System (VTLS), which couples digital control technology to hydropower plant equipment, are described. Prominent among these is the vibration diagnostics module for hydraulic turbines. It provides machine-specific diagnostic logic for a vibration monitoring and analysis system. Of the two other VTLS modules described, the operation module optimizes the control of a power plant with three or more turbines by considering the individual properties of each in turn, recommending which should be run, and how, in order to partition the load for a required power output. The cavitation module is a diagnostic system which enables the limits of operation of the turbines to be extended to bands just outside those determined by cavitation calculations. (3 figures). (UK)

  17. Pickin’ up good vibrations

    CERN Multimedia

    Katarina Anthony

    2015-01-01

    In preparation for the civil engineering work on the HL-LHC, vibration measurements were carried out at the LHC’s Point 1 last month. These measurements will help evaluate how civil engineering work could impact the beam, and will provide crucial details about the site’s geological make-up before construction begins.   A seismic truck at Point 1 generated wave-like vibrations measured by EN/MME. From carrying out R&D to produce state-of-the-art magnets to developing innovative, robust materials capable of withstanding beam impact, the HL-LHC is a multi-faceted project involving many groups and teams across CERN’s departments. It was in this framework that the project management mandated CERN's Mechanical and Materials Engineering (EN/MME) group to measure the propagation of vibrations around Point 1. Their question: can civil engineering work for the HL-LHC – the bulk of which is scheduled for LS2 – begin while the LHC is running? Alth...

  18. Vibrational stability of graphene

    Directory of Open Access Journals (Sweden)

    Yangfan Hu

    2013-05-01

    Full Text Available The mechanical stability of graphene as temperature rises is analyzed based on three different self-consistent phonon (SCP models. Compared with three-dimensional (3-D materials, the critical temperature Ti at which instability occurs for graphene is much closer to its melting temperature Tm obtained from Monte Carlo simulation (Ti ≃ 2Tm, K. V. Zakharchenko, A. Fasolino, J. H. Los, and M. I. Katsnelson, J. Phys. Condens. Matter 23, 202202. This suggests that thermal vibration plays a significant role in melting of graphene while melting for 3-D materials is often dominated by topologic defects. This peculiar property of graphene derives from its high structural anisotropy, which is characterized by the vibrational anisotropic coefficient (VAC, defined upon its Lindermann ratios in different directions. For any carbon based material with a graphene-like structure, the VAC value must be smaller than 5.4 to maintain its stability. It is also found that the high VAC value of graphene is responsible for its negative thermal expansion coefficient at low temperature range. We believe that the VAC can be regarded as a new criterion concerning the vibrational stability of any low-dimensional (low-D materials.

  19. Laryngeal High-Speed Videoendoscopy: Sensitivity of Objective Parameters towards Recording Frame Rate

    OpenAIRE

    Anne Schützenberger; Melda Kunduk; Michael Döllinger; Christoph Alexiou; Denis Dubrovskiy; Marion Semmler; Anja Seger; Christopher Bohr

    2016-01-01

    The current use of laryngeal high-speed videoendoscopy in clinic settings involves subjective visual assessment of vocal fold vibratory characteristics. However, objective quantification of vocal fold vibrations for evidence-based diagnosis and therapy is desired, and objective parameters assessing laryngeal dynamics have therefore been suggested. This study investigated the sensitivity of the objective parameters and their dependence on recording frame rate. A total of 300 endoscopic high-sp...

  20. Force illusions and drifts observed during muscle vibration.

    Science.gov (United States)

    Reschechtko, Sasha; Cuadra, Cristian; Latash, Mark L

    2018-01-01

    We explored predictions of a scheme that views position and force perception as a result of measuring proprioceptive signals within a reference frame set by ongoing efferent process. In particular, this hypothesis predicts force illusions caused by muscle vibration and mediated via changes in both afferent and efferent components of kinesthesia. Healthy subjects performed accurate steady force production tasks by pressing with the four fingers of one hand (the task hand) on individual force sensors with and without visual feedback. At various times during the trials, subjects matched the perceived force using the other hand. High-frequency vibration was applied to one or both of the forearms (over the hand and finger extensors). Without visual feedback, subjects showed a drop in the task hand force, which was significantly smaller under the vibration of that forearm. Force production by the matching hand was consistently higher than that of the task hand. Vibrating one of the forearms affected the matching hand in a manner consistent with the perception of higher magnitude of force produced by the vibrated hand. The findings were consistent between the dominant and nondominant hands. The effects of vibration on both force drift and force mismatching suggest that vibration led to shifts in both signals from proprioceptors and the efferent component of perception, the referent coordinate and/or coactivation command. The observations fit the hypothesis on combined perception of kinematic-kinetic variables with little specificity of different groups of peripheral receptors that all contribute to perception of forces and coordinates. NEW & NOTEWORTHY We show that vibration of hand/finger extensors produces consistent errors in finger force perception. Without visual feedback, finger force drifted to lower values without a drift in the matching force produced by the other hand; hand extensor vibration led to smaller finger force drift. The findings fit the scheme with

  1. VIBRATION ISOLATION SYSTEM PROBABILITY ANALYSIS

    Directory of Open Access Journals (Sweden)

    Smirnov Vladimir Alexandrovich

    2012-10-01

    Full Text Available The article deals with the probability analysis for a vibration isolation system of high-precision equipment, which is extremely sensitive to low-frequency oscillations even of submicron amplitude. The external sources of low-frequency vibrations may include the natural city background or internal low-frequency sources inside buildings (pedestrian activity, HVAC. Taking Gauss distribution into account, the author estimates the probability of the relative displacement of the isolated mass being still lower than the vibration criteria. This problem is being solved in the three dimensional space, evolved by the system parameters, including damping and natural frequency. According to this probability distribution, the chance of exceeding the vibration criteria for a vibration isolation system is evaluated. Optimal system parameters - damping and natural frequency - are being developed, thus the possibility of exceeding vibration criteria VC-E and VC-D is assumed to be less than 0.04.

  2. Random vibrations theory and practice

    CERN Document Server

    Wirsching, Paul H; Ortiz, Keith

    1995-01-01

    Random Vibrations: Theory and Practice covers the theory and analysis of mechanical and structural systems undergoing random oscillations due to any number of phenomena— from engine noise, turbulent flow, and acoustic noise to wind, ocean waves, earthquakes, and rough pavement. For systems operating in such environments, a random vibration analysis is essential to the safety and reliability of the system. By far the most comprehensive text available on random vibrations, Random Vibrations: Theory and Practice is designed for readers who are new to the subject as well as those who are familiar with the fundamentals and wish to study a particular topic or use the text as an authoritative reference. It is divided into three major sections: fundamental background, random vibration development and applications to design, and random signal analysis. Introductory chapters cover topics in probability, statistics, and random processes that prepare the reader for the development of the theory of random vibrations a...

  3. Mechanical Energy Change in Inertial Reference Frames

    Science.gov (United States)

    Ghanbari, Saeed

    2016-01-01

    The mechanical energy change of a system in an inertial frame of reference equals work done by the total nonconservative force in the same frame. This relation is covariant under the Galilean transformations from inertial frame S to S', where S' moves with constant velocity relative to S. In the presence of nonconservative forces, such as normal…

  4. Oversampling of wavelet frames for real dilations

    DEFF Research Database (Denmark)

    Bownik, Marcin; Lemvig, Jakob

    2012-01-01

    We generalize the Second Oversampling Theorem for wavelet frames and dual wavelet frames from the setting of integer dilations to real dilations. We also study the relationship between dilation matrix oversampling of semi-orthogonal Parseval wavelet frames and the additional shift invariance gain...

  5. Classifying tight Weyl-Heisenberg frames

    DEFF Research Database (Denmark)

    Cazsazza, P.; Janssen, A. J. E. M.; Christensen, Ole

    1999-01-01

    A Weyl-Heisenberg frame for L^2(R) is a frame consisting of translates and modulates of a fixed function. In this paper we give necessary and sufficient conditions for this family to form a tight WH-frame. This allows us to write down explicitly all functions g for which all translates and modula...

  6. 21 CFR 886.5842 - Spectacle frame.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Spectacle frame. 886.5842 Section 886.5842 Food... DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5842 Spectacle frame. (a) Identification. A spectacle frame is a device made of metal or plastic intended to hold prescription spectacle lenses worn by a...

  7. Parametric Study Of Window Frame Geometry

    DEFF Research Database (Denmark)

    Zajas, Jan Jakub; Heiselberg, Per

    2013-01-01

    This paper describes a parametric study on window frame geometry with the goal of designing frames with very good thermal properties. Three different parametric frame models are introduced, deseribed by a number of variables. In the first part of the study, a process of sensitivity analysis...

  8. Common Frame of Reference and social justice

    NARCIS (Netherlands)

    Hesselink, M.W.; Satyanarayana, R.

    2009-01-01

    The article "Common Frame of Reference and Social Justice" by Martijn W. Hesselink evaluates the Draft Common Frame of Reference (DCFR) of social justice. It discusses the important areas, namely a common frame of Reference in a broad sense, social justice and contract law, private law and

  9. Popcorn Story Frames from a Multicultural Perspective.

    Science.gov (United States)

    DiLella, Carol Ann

    Popcorn story frames from a multicultural perspective are holistic outlines that in the reading/writing process facilitate comprehension for all cultures learning to read and write stories. Popcorn story frames are structured and modeled in a horizontal fashion just like popcorn pops in a horizontal fashion. The frames are designed for learners…

  10. Evaluation and the Framing of Race

    Science.gov (United States)

    House, Ernest R.

    2017-01-01

    Racial framing can have strong effects on programs, policies, and even evaluations. Racial framing developed as a justification for the exploitation of minorities and has been a primary causal factor in the persistence of racism. By being aware of its pattern, structure, origins, and how racial framing generates effects, we can significantly…

  11. Fight or flight: Affective news framing effects

    NARCIS (Netherlands)

    Feinholdt, A.

    2016-01-01

    This dissertation investigates how emotions shape and are shaped by news framing and how this interplay leads to a number of affective news framing effects. My work reveals that emotions do not only function as mechanisms but also as channels strengthening or weakening framing effects. In addition,

  12. PARAMETRIC RESONANSE IN STATICALLY INDETERMINATE FRAMES

    Directory of Open Access Journals (Sweden)

    Yu.V. Vorona

    2014-12-01

    Full Text Available The technique for development and reduction of discrete dynamics models of frames is presented. Construction of the models is carried out using finite element method, generalized coordinates and tools of modern computer software. Parametric resonance in a statically indeterminate frame caused by external excitations is investigated. Main instability domains of the frame are determined.

  13. Vision-Based Faint Vibration Extraction Using Singular Value Decomposition

    Directory of Open Access Journals (Sweden)

    Xiujun Lei

    2015-01-01

    Full Text Available Vibration measurement is important for understanding the behavior of engineering structures. Unlike conventional contact-type measurements, vision-based methodologies have attracted a great deal of attention because of the advantages of remote measurement, nonintrusive characteristic, and no mass introduction. It is a new type of displacement sensor which is convenient and reliable. This study introduces the singular value decomposition (SVD methods for video image processing and presents a vibration-extracted algorithm. The algorithms can successfully realize noncontact displacement measurements without undesirable influence to the structure behavior. SVD-based algorithm decomposes a matrix combined with the former frames to obtain a set of orthonormal image bases while the projections of all video frames on the basis describe the vibration information. By means of simulation, the parameters selection of SVD-based algorithm is discussed in detail. To validate the algorithm performance in practice, sinusoidal motion tests are performed. Results indicate that the proposed technique can provide fairly accurate displacement measurement. Moreover, a sound barrier experiment showing how the high-speed rail trains affect the sound barrier nearby is carried out. It is for the first time to be realized at home and abroad due to the challenge of measuring environment.

  14. Rigid Motion and Adapted Frames

    Science.gov (United States)

    Lyle, Stephen N.

    The aim here is to describe the rigid motion of a continuous medium in special and general relativity. Section 7.1 defines a rigid rod in special relativity, and Sect. 7.2 shows the link with the space coordinates of a certain kind of accelerating frame in flat spacetimes. Section 7.3 then sets up a notation for describing the arbitrary smooth motion of a continuous medium in general curved spacetimes, defining the proper metric of such a medium. Section 7.4 singles out rigid motions and shows that the rod in Sect. 7.1 undergoes rigid motion in the more generally defined sense. Section 7.5 defines a rate of strain tensor for a continuous medium in general relativity and reformulates the rigidity criterion. Section 7.6 aims to classify all possible rigid motions in special relativity, reemphasizing the link with semi-Euclidean frames adapted to accelerating observers in special relativity. Then, Sects. 7.7 and 7.8 describe rigid motion without rotation and rigid rotation, respectively. Along the way we introduce the notion of Fermi-Walker transport and discuss its relevance for rigid motions. Section 7.9 brings together all the above themes in an account of a recent generalization of the notion of uniform acceleration, thereby characterizing a wide class of rigid motions.

  15. Two methods for modeling vibrations of planetary gearboxes including faults: Comparison and validation

    Science.gov (United States)

    Parra, J.; Vicuña, Cristián Molina

    2017-08-01

    Planetary gearboxes are important components of many industrial applications. Vibration analysis can increase their lifetime and prevent expensive repair and safety concerns. However, an effective analysis is only possible if the vibration features of planetary gearboxes are properly understood. In this paper, models are used to study the frequency content of planetary gearbox vibrations under non-fault and different fault conditions. Two different models are considered: phenomenological model, which is an analytical-mathematical formulation based on observation, and lumped-parameter model, which is based on the solution of the equations of motion of the system. Results of both models are not directly comparable, because the phenomenological model provides the vibration on a fixed radial direction, such as the measurements of the vibration sensor mounted on the outer part of the ring gear. On the other hand, the lumped-parameter model provides the vibrations on the basis of a rotating reference frame fixed to the carrier. To overcome this situation, a function to decompose the lumped-parameter model solutions to a fixed reference frame is presented. Finally, comparisons of results from both model perspectives and experimental measurements are presented.

  16. Chaotic vortex induced vibrations

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, J.; Sheridan, J. [Fluids Laboratory for Aeronautical and Industrial Research (FLAIR), Department of Mechanical and Aerospace Engineering, Monash University, Melbourne, Victoria 3800 (Australia); Leontini, J. S. [Department of Mechanical and Product Design Engineering, Swinburne University of Technology, Hawthorn, Victoria 3122 (Australia); Lo Jacono, D. [Institut de Mécanique des Fluides de Toulouse (IMFT), CNRS, UPS and Université de Toulouse, 31400 Toulouse (France)

    2014-12-15

    This study investigates the nature of the dynamic response of an elastically mounted cylinder immersed in a free stream. A novel method is utilized, where the motion of the body during a free vibration experiment is accurately recorded, and then a second experiment is conducted where the cylinder is externally forced to follow this recorded trajectory. Generally, the flow response during both experiments is identical. However, particular regimes exist where the flow response is significantly different. This is taken as evidence of chaos in these regimes.

  17. Lattice Vibrations in Chlorobenzenes:

    DEFF Research Database (Denmark)

    Reynolds, P. A.; Kjems, Jørgen; White, J. W.

    1974-01-01

    Lattice vibrational dispersion curves for the ``intermolecular'' modes in the triclinic, one molecule per unit cell β phase of p‐C6D4Cl2 and p‐C6H4Cl2 have been obtained by inelastic neutron scattering. The deuterated sample was investigated at 295 and at 90°K and a linear extrapolation to 0°K...... was applied in order to correct for anharmonic effects. Calculations based on the atom‐atom model for van der Waals' interaction and on general potential parameters for the aromatic compounds agree reasonably well with the experimental observations. There is no substantial improvement in fit obtained either...

  18. Frame ambiguity in policy controversies: critical frame analysis of migrant integration policies in Antwerp and Rotterdam

    NARCIS (Netherlands)

    R. Dekker (Rianne)

    2017-01-01

    textabstractPolicy frames are understood as the outcome of a policy process in which multiple frames are contesting, but where one frame prevails and characterizes policies. Policy frames are therefore perceived and studied as coherent interpretations of a policy issue containing a problem

  19. Effects of gain-loss frames in negotiation: Loss aversion, mismatching, and frame adoption

    NARCIS (Netherlands)

    de Dreu, C.K.W.; Emans, B.J.M.; van de Vliert, E.; Carnevale, P.J.

    1994-01-01

    Examined negotiator cognition and behavior as a function of own frame, foreknowledge about opponent's frame, opponent's communicated frame, and their interactions. Prenegotiation information about the opponent's gain or loss frame on negotiator cognition and behavior was also examined. Ss were 107

  20. Quantum dynamics of vibrational excitations and vibrational charge ...

    Indian Academy of Sciences (India)

    Quantum dynamics of vibrational excitations and vibrational charge transfer processes in H+ + O2 collisions at collision energy 23 eV ... The Fritz Haber Research Centre and The Department of Physical Chemisry, Hebrew University of Jerusalem, Jerusalem, Israel 91904; Department of Chemistry, Indian Institute of ...

  1. Message framing in social networking sites.

    Science.gov (United States)

    Kao, Danny Tengti; Chuang, Shih-Chieh; Wang, Sui-Min; Zhang, Lei

    2013-10-01

    Online social networking sites represent significant new opportunities for Internet advertisers. However, results based on the real world cannot be generalized to all virtual worlds. In this research, the moderating effects of need for cognition (NFC) and knowledge were applied to examine the impact of message framing on attitudes toward social networking sites. A total of 216 undergraduates participated in the study. Results reveal that for social networking sites, while high-NFC individuals form more favorable attitudes toward negatively framed messages than positively framed messages, low-NFC individuals form more favorable attitudes toward positively framed messages than negatively framed messages. In addition, low-knowledge individuals demonstrate more favorable attitudes toward negatively framed messages than positively framed messages; however, the framing effect does not differentially affect the attitudes of high-knowledge individuals. Furthermore, the framing effect does not differentially affect the attitudes of high-NFC individuals with high knowledge. In contrast, low-NFC individuals with low knowledge hold more favorable attitudes toward positively framed messages than negatively framed messages.

  2. An introduction to finite tight frames

    CERN Document Server

    Waldron, Shayne F D

    2018-01-01

    This textbook is an introduction to the theory and applications of finite tight frames, an area that has developed rapidly in the last decade. Stimulating much of this growth are the applications of finite frames to diverse fields such as signal processing, quantum information theory, multivariate orthogonal polynomials, and remote sensing. Key features and topics: * First book entirely devoted to finite frames * Extensive exercises and MATLAB examples for classroom use * Important examples, such as harmonic and Heisenberg frames, are presented in preliminary chapters, encouraging readers to explore and develop an intuitive feeling for tight frames * Later chapters delve into general theory details and recent research results * Many illustrations showing the special aspects of the geometry of finite frames * Provides an overview of the field of finite tight frames * Discusses future research directions in the field Featuring exercises and MATLAB examples in each chapter, the book is well suited as a textbook ...

  3. Characterization of Oblique Dual Frame Pairs

    DEFF Research Database (Denmark)

    Christensen, Ole; Eldar, Yonina

    2006-01-01

    Given a frame for a subspace W of a Hilbert space H, we consider all possible families of oblique dual frame vectors on an appropriately chosen subspace V. In place of the standard description, which involves computing the pseudoinverse of the frame operator, we develop an alternative...... characterization which in some cases can be computationally more efficient. We first treat the case of a general frame on an arbitrary Hilbert space, and then specialize the results to shift-invariant frames with multiple generators. In particular, we present explicit versions of our general conditions...... for the case of shift-invariant spaces with a single generator. The theory is also adapted to the standard frame setting in which the original and dual frames are defined on the same space. Copyright (C) 2006 Hindawi Publishing Corporation. All rights reserved....

  4. Analisis Framing dalam Riset Public Relations

    Directory of Open Access Journals (Sweden)

    NARAYANA MAHENDRA PRASTYA

    2016-12-01

    Full Text Available This paper aims to give description about how to use frame analysis in Public Relations (PR research. The author use two framing models: Entman and Pan & Kosicki. The object is organization official statement about particular issue. Frame analysis method rarely used in Public Relations research. This methods commonly use in journalism study, to analyse the news in media. Meanwhile, the key word of framing is the social construction of reality. Organization can make social construction of realty in their official statement. In acacemic term, frame analysis in PR research is useful to know how organization positioned themselves in particular situation. Other benefit is use to evaluat whether the organization frame is conformable with the public opinion or agenda setting media or not. In practical term, frame analysis give benefit for PR practitioner to create the message that can be undserstood by public, also give positive image for organization.

  5. Framing: la perspectiva de las noticias

    Directory of Open Access Journals (Sweden)

    Aruguete, Natalia

    2011-01-01

    Full Text Available [es] Este trabajo consiste en una revisión teórica de la Teoría del Framing o Teoría del Encuadre. A lo largo del texto se desarrollan los orígenes de esta corriente, las definiciones propuestas para el término frame o framing por diversos autores, los tipos de frames existentes, las dimensiones utilizadas para su estudio empírico y los abordajes metodológicos para su identificación en la información mediática. [en] This work is a theoretical review of the Framing Theory. Throughout the text develops the origins of this perspective, the definitions proposed for the concept frame by different authors, the existing types of frames, the dimensions used for empirical research and methodological approaches for identification of the information media

  6. Literature survey on anti-vibration gloves

    CSIR Research Space (South Africa)

    Sampson, E

    2003-08-01

    Full Text Available ............................................................................................................... 1 2. HAND ARM VIBRATION SYNDROME (HAVS).......................................................... 2 2.1 Hand-arm vibration................................................. Error! Bookmark not defined. 2.2 Human Response to vibration...

  7. Discursive Framings of Human Rights

    DEFF Research Database (Denmark)

    and social contexts. Historical as well as contemporary declarations of rights have stressed both the protective and political aspects of human rights. But in concrete situations and conflictual moments, the high moral legitimacy of human rights rhetoric has often clouded the actual character of specific......What does it mean to be a subject of human rights? The status of the subject is closely connected with the form and rhetoric of the framing discourse, and this book investigates the relationship between the status of the subject and the form of human rights discourse, in differing aesthetic...... interventions, and so made it difficult to differentiate between the objects of humanitarian intervention and the subjects of politics. Critically re-examining this opposition – between victims and agents of human rights – through a focus on the ways in which discourses of rights are formed and circulated...

  8. Vibrational Sensing in Marine Invertebrates

    Science.gov (United States)

    1997-09-30

    VIBRATIONAL SENSING IN MARINE INVERTEBRATES Peter A. Jumars School of Oceanography University of Washington Box 357940 Seattle, WA 98195-7940 (206...DATES COVERED 00-00-1997 to 00-00-1997 4. TITLE AND SUBTITLE Vibrational Sensing in Marine Invertebrates 5a. CONTRACT NUMBER 5b. GRANT NUMBER

  9. Vibrations and Stability: Solved Problems

    DEFF Research Database (Denmark)

    Thomsen, Jon Juel

    Worked out solutions for exercise problems in J. J. Thomsen 'Vibrations and Stability: Advanced Theory, Analysis, and Tools', Springer, Berlin - Heidelberg, 2003.......Worked out solutions for exercise problems in J. J. Thomsen 'Vibrations and Stability: Advanced Theory, Analysis, and Tools', Springer, Berlin - Heidelberg, 2003....

  10. Modelling Micro-Vibrations By Finite Element Model Approach

    Science.gov (United States)

    Soula, Laurent; Laduree, Gregory

    2012-07-01

    With payloads requiring more and more severe environment stability and spacecrafts becoming more and more sensitive to internal mechanical disturbances, micro-vibrations are a key contributor to the performance of new missions. To help predict such behaviour by analyses and verify it by testing, a “METhodology for Analysis of structure-borne MICro- vibrations” is being defined in the frame of the above- named ESA R&D study (METAMIC). This methodology is soon to be validated by a full-test campaign. Meanwhile, this paper proposes a description of the current processes using the Finite Element Models, which start from the perturbation source. Based on ASTRIUM experience, a classification of disturbance sources is proposed. Three different types are selected to illustrate the modelling and the micro- vibrations characterization performed by tests: momentum wheels, cryo-coolers, and stepper motor mechanisms. The perturbation is then to be implemented into system modelling in order to predict its propagation and effect on overall performance. The main assumptions made on structure modelling have to be identified as well as the level of coupling with the disturbance sources has to be anticipated. Most of the questions a project should ask to deal with micro- vibrations are tackled, with the objective to identify all uncertainties, limitations, and validity domains for micro-vibrations prediction.

  11. Simulation on Vehicle Vibration Offset of NX70 Flatcar

    Directory of Open Access Journals (Sweden)

    Han Yanhui

    2014-11-01

    Full Text Available The current rolling stock gauge for standard gauge railway is a static gauge to check the vehicle frame. The contradiction of large construction gauge and small rolling stock gauge has always existed. It is important to set down the clearance requirements in respect of physical size for the safe passage of rail vehicles. Reasonably determining the maximum vibration offset can improve the efficiency of clearance. As an example, analyze the complex vibration of NX70 flat car by simulation test on the running track. Comprehensive considering the track model, loading plan, line conditions and running speed, then SIMPACK is used to present the vehicle system dynamics simulation model. After researching simulation result, respectively determine the maximum vehicle vibration offset for railroads of Class I, Class II and Class III on the height of the center of gravity 2000 mm and 2400 mm. According to the clearance between the structure gauge and the position of maximum vibration offset, analyze the safety of vehicle operation since the center of gravity is higher than before.

  12. U-shape magnetostrictive vibration based power generator for universal use

    Science.gov (United States)

    Ueno, T.

    2016-04-01

    Vibrational power generator extracts electrical energy from ambient vibration. Author invented novel configuration using magnetostrictive material. The device is based on parallel beams of iron-gallium alloy and magnetic material, and features high efficiency, high robustness, and low electrical impedance. In this paper, author proposes U-shape generator for universal use. It consists of the parallel beams and fixed and free end beams forming U-shape frame flexibly modified for variety of mechanical input. Miniature U-shape prototype using Fe-Ga rod 6 by 0.5 by 13 mm3 exhibited average power of 3.7 mW under vibration of 166 Hz and 2.5 G. L-shape type was demonstrated to generate electromotive force by two directional vibrations. In switch type, maximum energy of 0.7 mJ was retrieved by one pushing force. The performances are sufficient to drive wireless module for heath monitoring and remote control.

  13. The origins of vibration theory

    Science.gov (United States)

    Dimarogonas, A. D.

    1990-07-01

    The Ionian School of natural philosophy introduced the scientific method of dealing with natural phenomena and the rigorous proofs for abstract propositions. Vibration theory was initiated by the Pythagoreans in the fifth century BC, in association with the theory of music and the theory of acoustics. They observed the natural frequency of vibrating systems and proved that it is a system property and that it does not depend on the excitation. Pythagoreans determined the fundamental natural frequencies of several simple systems, such as vibrating strings, pipes, vessels and circular plates. Aristoteles and the Peripatetic School founded mechanics and developed a fundamental understanding of statics and dynamics. In Alexandrian times there were substantial engineering developments in the field of vibration. The pendulum as a vibration, and probably time, measuring device was known in antiquity, and was further developed by the end of the first millennium AD.

  14. Attenuation of cryocooler induced vibration using multimodal tuned dynamic absorber

    Science.gov (United States)

    Veprik, A.; Babitsky, V.; Tuito, A.

    2017-12-01

    Modern infrared imagers often rely on low Size, Weight and Power split Stirling linear cryocoolers comprised of side-by-side packed compressor and expander units fixedly mounted upon a common frame and interconnected by the configurable transfer line. Imbalanced reciprocation of moving assemblies generates vibration export in the form of tonal force couple producing angular and translational dynamic responses. Resulting line of sight jitter and dynamic defocusing may affect the image quality. The authors explore the concept of multimodal tuned dynamic absorber, the translational and tilting modal frequencies of which are essentially matched to the driving frequency. Dynamic analysis and full-scale testing show that the dynamic reactions (forces and moments) produced by such a device may effectively attenuate both translational and angular components of cryocooler-induced vibration.

  15. The characteristics of a successful framing process

    DEFF Research Database (Denmark)

    Haase, Louise Møller

    2017-01-01

    or creating several revisions of the frame. This research project aims at identifying further actions, which can support a successful framing process. The study builds upon indications from a previous study presented at E&PDE 2016, where a small number of students were asked to document their framing process...... mainly focused on describing the different steps in the process or by describing the type of reasoning that lies behind the framing process. Only a few studies have provided insights into the type of actions that is needed to achieve a successful framing process i.e. searching for the paradox in the data......In design schools and university we need to teach students how to frame their projects in ways that create a significant and new perspective on the problem situation as well as clear direction for the solution. We teach students how to engage in user research, prototyping, conceptualization...

  16. Asteroid Ida - Five Frame Mosaic

    Science.gov (United States)

    1993-01-01

    This view of the asteroid 243 Ida is a mosaic of five image frames acquired by the Galileo spacecraft's solid-state imaging system at ranges of 3,057 to 3,821 kilometers (1,900 to 2,375 miles) on August 28, 1993, about 3-1/2 minutes before the spacecraft made its closest approach to the asteroid. Galileo flew about 2,400 kilometers (1,500 miles) from Ida at a relative velocity of 12.4 km/sec (28,000 mph). Asteroid and spacecraft were 441 million kilometers (274 million miles) from the Sun. Ida is the second asteroid ever encountered by a spacecraft. It appears to be about 52 kilometers (32 miles) in length, more than twice as large as Gaspra, the first asteroid observed by Galileo in October 1991. Ida is an irregularly shaped asteroid placed by scientists in the S class (believed to be like stony or stony iron meteorites). It is a member of the Koronis family, presumed fragments left from the breakup of a precursor asteroid in a catastrophic collision. This view shows numerous craters, including many degraded craters larger than any seen on Gaspra. The extensive cratering seems to dispel theories about Ida's surface being geologically youthful. This view also seems to rule out the idea that Ida is a double body. The south pole is believed to be in the darkside near the middle of the asteroid. The camera's clear filter was used to produce this extremely sharp picture. Spatial resolution is 31 to 38 meters (roughly 100 feet) per pixel. A 30-frame mosaic was taken to assure capturing Ida; its position was somewhat uncertain before the Galileo encounter. Galileo shuttered and recorded a total of 150 images in order to capture Ida 21 different times during a five hour period (about one rotation of the asteroid). Color filters were used at many of these times to allow reconstruction of color images. Playback to Earth of the remaining images is planned for April through June 1994. The Galileo project, whose primary mission is the exploration of the Jupiter system in 1995

  17. VESPA: The vibrational spectrometer for the European Spallation Source

    Energy Technology Data Exchange (ETDEWEB)

    Fedrigo, Anna, E-mail: anna.fedrigo@nbi.ku.dk [Niels Bohr Institute, University of Copenhagen, 2100 Copenhagen Ø (Denmark); Istituto dei Sistemi Complessi, Consiglio Nazionale delle Ricerche, 50019 Sesto Fiorentino (Italy); European Spallation Source ESS AB, SE-221 00 Lund (Sweden); Colognesi, Daniele; Grazzi, Francesco; Zoppi, Marco [Istituto dei Sistemi Complessi, Consiglio Nazionale delle Ricerche, 50019 Sesto Fiorentino (Italy); Bertelsen, Mads; Strobl, Markus [Niels Bohr Institute, University of Copenhagen, 2100 Copenhagen Ø (Denmark); European Spallation Source ESS AB, SE-221 00 Lund (Sweden); Hartl, Monika; Deen, Pascale P. [European Spallation Source ESS AB, SE-221 00 Lund (Sweden); Lefmann, Kim [Niels Bohr Institute, University of Copenhagen, 2100 Copenhagen Ø (Denmark)

    2016-06-15

    VESPA, Vibrational Excitation Spectrometer with Pyrolytic-graphite Analysers, aims to probe molecular excitations via inelastic neutron scattering. It is a thermal high resolution inverted geometry time-of-flight instrument designed to maximise the use of the long pulse of the European Spallation Source. The wavelength frame multiplication technique was applied to provide simultaneously a broad dynamic range (about 0-500 meV) while a system of optical blind choppers allows to trade flux for energy resolution. Thanks to its high flux, VESPA will allow the investigation of dynamical and in situ experiments in physical chemistry. Here we describe the design parameters and the corresponding McStas simulations.

  18. The Heroic Framing of US Foreign Policy

    OpenAIRE

    Shaw, Emily D.

    2010-01-01

    This dissertation concerns the US presidential use of heroic framing in connection with foreign policy. I identify "heroic framing" as speech which describes policies in terms evoking the heroic narrative, either explicitly or implicitly through references to heroic characters. The technique of heroic framing both encourages audiences to view a situation in terms of stark moral absolutes and normalizes casualties and violence as an aspect of these heroic conflicts. This rhetorical technique t...

  19. Nonlinear approximation with nonstationary Gabor frames

    DEFF Research Database (Denmark)

    Ottosen, Emil Solsbæk; Nielsen, Morten

    2018-01-01

    We consider sparseness properties of adaptive time-frequency representations obtained using nonstationary Gabor frames (NSGFs). NSGFs generalize classical Gabor frames by allowing for adaptivity in either time or frequency. It is known that the concept of painless nonorthogonal expansions...... resolution. Based on this characterization we prove an upper bound on the approximation error occurring when thresholding the coefficients of the corresponding frame expansions. We complement the theoretical results with numerical experiments, estimating the rate of approximation obtained from thresholding...

  20. Journalism Curiosity and Story Telling Frame

    DEFF Research Database (Denmark)

    Grunwald, Ebbe; Rupar, Verica

    2009-01-01

    This comparative study of journalism practices in Australia and Denmark explores the interplay between two concepts relevant for journalism's meaning-making activity: a curiosity seen as an action meant to close an information gap, and a story telling frame seen as a form of structuring information...... the epistemological and organisational dimension of frames relates to the process of  meaning-making. We suggest refining the concept of frame in journalism studies by making a distinction between a frame (an epistemological category) and an angle (a textual organisation category). Our investigation shows...... that this distinction better serves the analysis and understanding of the mechanisms behind journalism in comparative contexts. Udgivelsesdato: December...

  1. Pilotless Frame Synchronization Using LDPC Code Constraints

    Science.gov (United States)

    Jones, Christopher; Vissasenor, John

    2009-01-01

    A method of pilotless frame synchronization has been devised for low- density parity-check (LDPC) codes. In pilotless frame synchronization , there are no pilot symbols; instead, the offset is estimated by ex ploiting selected aspects of the structure of the code. The advantag e of pilotless frame synchronization is that the bandwidth of the sig nal is reduced by an amount associated with elimination of the pilot symbols. The disadvantage is an increase in the amount of receiver data processing needed for frame synchronization.

  2. Framing: la perspectiva de las noticias

    OpenAIRE

    Aruguete, Natalia

    2011-01-01

    [es] Este trabajo consiste en una revisión teórica de la Teoría del Framing o Teoría del Encuadre. A lo largo del texto se desarrollan los orígenes de esta corriente, las definiciones propuestas para el término frame o framing por diversos autores, los tipos de frames existentes, las dimensiones utilizadas para su estudio empírico y los abordajes metodológicos para su identificación en la información mediática. [en] This work is a theoretical rev...

  3. Localized surface plasmon resonances in nanostructures to enhance nonlinear vibrational spectroscopies: towards an astonishing molecular sensitivity

    Directory of Open Access Journals (Sweden)

    Dan Lis

    2014-11-01

    Full Text Available Vibrational transitions contain some of the richest fingerprints of molecules and materials, providing considerable physicochemical information. Vibrational transitions can be characterized by different spectroscopies, and alternatively by several imaging techniques enabling to reach sub-microscopic spatial resolution. In a quest to always push forward the detection limit and to lower the number of needed vibrational oscillators to get a reliable signal or imaging contrast, surface plasmon resonances (SPR are extensively used to increase the local field close to the oscillators. Another approach is based on maximizing the collective response of the excited vibrational oscillators through molecular coherence. Both features are often naturally combined in vibrational nonlinear optical techniques. In this frame, this paper reviews the main achievements of the two most common vibrational nonlinear optical spectroscopies, namely surface-enhanced sum-frequency generation (SE-SFG and surface-enhanced coherent anti-Stokes Raman scattering (SE-CARS. They can be considered as the nonlinear counterpart and/or combination of the linear surface-enhanced infrared absorption (SEIRA and surface-enhanced Raman scattering (SERS techniques, respectively, which are themselves a branching of the conventional IR and spontaneous Raman spectroscopies. Compared to their linear equivalent, those nonlinear vibrational spectroscopies have proved to reach higher sensitivity down to the single molecule level, opening the way to astonishing perspectives for molecular analysis.

  4. Vibration response of misaligned rotors

    Science.gov (United States)

    Patel, Tejas H.; Darpe, Ashish K.

    2009-08-01

    Misalignment is one of the common faults observed in rotors. Effect of misalignment on vibration response of coupled rotors is investigated in the present study. The coupled rotor system is modelled using Timoshenko beam elements with all six dof. An experimental approach is proposed for the first time for determination of magnitude and harmonic nature of the misalignment excitation. Misalignment effect at coupling location of rotor FE model is simulated using nodal force vector. The force vector is found using misalignment coupling stiffness matrix, derived from experimental data and applied misalignment between the two rotors. Steady-state vibration response is studied for sub-critical speeds. Effect of the types of misalignment (parallel and angular) on the vibration behaviour of the coupled rotor is examined. Along with lateral vibrations, axial and torsional vibrations are also investigated and nature of the vibration response is also examined. It has been found that the misalignment couples vibrations in bending, longitudinal and torsional modes. Some diagnostic features in the fast Fourier transform (FFT) of torsional and longitudinal response related to parallel and angular misalignment have been revealed. Full spectra and orbit plots are effectively used to reveal the unique nature of misalignment fault leading to reliable misalignment diagnostic information, not clearly brought out by earlier studies.

  5. Framing a Story of Possibilities

    DEFF Research Database (Denmark)

    Svensson, Marie Kofod

    2017-01-01

    The article investigates the dynamics of photographic production by refugee and immigrant youth in a participatory photography project in San Diego, United States (The AjA Project). Based on five months of fieldwork and the concepts of ‘the takeable photograph’ and ‘the subjunctive mood’, it exam......The article investigates the dynamics of photographic production by refugee and immigrant youth in a participatory photography project in San Diego, United States (The AjA Project). Based on five months of fieldwork and the concepts of ‘the takeable photograph’ and ‘the subjunctive mood......’, it examines under what ideals the photographic production takes place. I argue that there are particular ‘takeable’ photographs in AjA framed by the emic concept of story and defined in opposition to students’ private photographs. ‘Takeable’ photographs are produced in and aim for the subjunctive mood...... to instill the process with a potential for positive change....

  6. Tissue vibration in prolonged running.

    Science.gov (United States)

    Friesenbichler, Bernd; Stirling, Lisa M; Federolf, Peter; Nigg, Benno M

    2011-01-04

    The impact force in heel-toe running initiates vibrations of soft-tissue compartments of the leg that are heavily dampened by muscle activity. This study investigated if the damping and frequency of these soft-tissue vibrations are affected by fatigue, which was categorized by the time into an exhaustive exercise. The hypotheses were tested that (H1) the vibration intensity of the triceps surae increases with increasing fatigue and (H2) the vibration frequency of the triceps surae decreases with increasing fatigue. Tissue vibrations of the triceps surae were measured with tri-axial accelerometers in 10 subjects during a run towards exhaustion. The frequency content was quantified with power spectra and wavelet analysis. Maxima of local vibration intensities were compared between the non-fatigued and fatigued states of all subjects. In axial (i.e. parallel to the tibia) and medio-lateral direction, most local maxima increased with fatigue (supporting the first hypothesis). In anterior-posterior direction no systematic changes were found. Vibration frequency was minimally affected by fatigue and frequency changes did not occur systematically, which requires the rejection of the second hypothesis. Relative to heel-strike, the maximum vibration intensity occurred significantly later in the fatigued condition in all three directions. With fatigue, the soft tissue of the triceps surae oscillated for an extended duration at increased vibration magnitudes, possibly due to the effects of fatigue on type II muscle fibers. Thus, the protective mechanism of muscle tuning seems to be reduced in a fatigued muscle and the risk of potential harm to the tissue may increase. Copyright © 2010 Elsevier Ltd. All rights reserved.

  7. Putting framing in perspective: A review of framing and frame analysis across the sensemaking, social movements and institutional literatures

    NARCIS (Netherlands)

    Cornelissen, J.P.; Werner, M.D.

    2014-01-01

    There are few constructs that are as ubiquitous across traditions of management and organizational research, and indeed the social sciences more generally, as that of frame or framing. The widespread popularity and use of the concept has led to rich streams of research, ranging from work in

  8. Molecular vibrations the theory of infrared and Raman vibrational spectra

    CERN Document Server

    Wilson, E Bright; Cross, Paul C

    1980-01-01

    Pedagogical classic and essential reference focuses on mathematics of detailed vibrational analyses of polyatomic molecules, advancing from application of wave mechanics to potential functions and methods of solving secular determinant.

  9. Avoid heat transfer equipment vibration

    Energy Technology Data Exchange (ETDEWEB)

    Ganapathy, V.

    1987-06-01

    Tube bundles in heat exchangers, boilers, superheaters and heaters are often subject to vibration and noise problems. Vibration can lead to tube thinning and wear, resulting in tube failures. Excessive noise can be a problem to plant operating personnel. Large gas pressure drop across the equipment is also a side effect, which results in large operating costs. With the design checks presented in this paper, one can predict during design if problems associated with noise and vibration are likely to occur in petroleum refineries.

  10. 14 CFR 33.63 - Vibration.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Vibration. 33.63 Section 33.63 Aeronautics... STANDARDS: AIRCRAFT ENGINES Design and Construction; Turbine Aircraft Engines § 33.63 Vibration. Each engine... because of vibration and without imparting excessive vibration forces to the aircraft structure. ...

  11. 14 CFR 33.83 - Vibration test.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Vibration test. 33.83 Section 33.83... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.83 Vibration test. (a) Each engine must undergo vibration surveys to establish that the vibration characteristics of those components that...

  12. 14 CFR 33.33 - Vibration.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Vibration. 33.33 Section 33.33 Aeronautics... STANDARDS: AIRCRAFT ENGINES Design and Construction; Reciprocating Aircraft Engines § 33.33 Vibration. The... vibration and without imparting excessive vibration forces to the aircraft structure. ...

  13. 14 CFR 33.43 - Vibration test.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Vibration test. 33.43 Section 33.43... STANDARDS: AIRCRAFT ENGINES Block Tests; Reciprocating Aircraft Engines § 33.43 Vibration test. (a) Each engine must undergo a vibration survey to establish the torsional and bending vibration characteristics...

  14. 49 CFR 178.819 - Vibration test.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Vibration test. 178.819 Section 178.819... Testing of IBCs § 178.819 Vibration test. (a) General. The vibration test must be conducted for the... vibration test. (b) Test method. (1) A sample IBC, selected at random, must be filled and closed as for...

  15. Rectangular Parallelepiped Vibration in Plane Strain State

    OpenAIRE

    Hanckowiak, Jerzy

    2004-01-01

    In this paper we present a vibration spectrum of a homogenous parallelepiped (HP) under the action of volume and surface forces resulting from the exponent displacements entering the Fourier transforms. Vibration under the action of axial surface tractions and the free vibration are described separately. A relationship between the high frequency vibration and boundary conditions (BC) is also considered.

  16. Frequency Identification of Vibration Signals Using Video Camera Image Data

    Directory of Open Access Journals (Sweden)

    Chia-Hung Wu

    2012-10-01

    Full Text Available This study showed that an image data acquisition system connecting a high-speed camera or webcam to a notebook or personal computer (PC can precisely capture most dominant modes of vibration signal, but may involve the non-physical modes induced by the insufficient frame rates. Using a simple model, frequencies of these modes are properly predicted and excluded. Two experimental designs, which involve using an LED light source and a vibration exciter, are proposed to demonstrate the performance. First, the original gray-level resolution of a video camera from, for instance, 0 to 256 levels, was enhanced by summing gray-level data of all pixels in a small region around the point of interest. The image signal was further enhanced by attaching a white paper sheet marked with a black line on the surface of the vibration system in operation to increase the gray-level resolution. Experimental results showed that the Prosilica CV640C CMOS high-speed camera has the critical frequency of inducing the false mode at 60 Hz, whereas that of the webcam is 7.8 Hz. Several factors were proven to have the effect of partially suppressing the non-physical modes, but they cannot eliminate them completely. Two examples, the prominent vibration modes of which are less than the associated critical frequencies, are examined to demonstrate the performances of the proposed systems. In general, the experimental data show that the non-contact type image data acquisition systems are potential tools for collecting the low-frequency vibration signal of a system.

  17. 290 Supervisors' Leadership Frames: Implications for ...

    African Journals Online (AJOL)

    User

    Abstract. The purpose of this study was to explore the leadership frames of supervisor of public schools in Nigeria required for effective implementation of. Universal Basic Education (UBE) in Nigeria. This study draws on work of. Bolman and Deals (1990) four-Frame Leadership Model. Using Three research questions and ...

  18. News Framing in a Time of Terror

    DEFF Research Database (Denmark)

    Jørndrup, Hanne

    2016-01-01

    the attacks at the Charlie Hebdo office in Paris in January 2015. This article analyses how the Danish television channel DR1 framed the attacks in the newscast from the first shot at Krudttønden and for the following week. Furthermore, the analysis will discuss how the framing of the shooting as a “terror...

  19. Teaching the Dynamics of Framing Competitions

    Science.gov (United States)

    Rinke, Eike Mark

    2012-01-01

    Framing theory is one of the most thriving and complex fields of communication theory, and as such it has grown to be an integral part of many political communication, public opinion, and communication theory courses. Part of the complexity stems from scholars' efforts to develop accounts of framing processes that are closer to the "real world" of…

  20. Time-framing and health risks: editorial

    NARCIS (Netherlands)

    Brown, P.; Heyman, B.; Alaszewski, A.

    2013-01-01

    This special issue is the last in a four-part series Health Care Through the ‘Lens of Risk’, which focuses on risk categorisation, valuing, expecting and time-framing, respectively, and has been published in 2012-2013. The present editorial introduces the issue of time-framing in relation to an

  1. A Framing Primer for Community College Leaders

    Science.gov (United States)

    Nausieda, Ryan

    2014-01-01

    The purpose of this article is to be a tool for community college leaders, as well as campus members, to positively and effectively utilize framing on their campuses. The fictional case of Maggie Pascal at Midwestern Community College illustrates the process of framing the change of a new partnership with Wind Energy Corporation to internal…

  2. Theoretical research and experimental validation of elastic dynamic load spectra on bogie frame of high-speed train

    Science.gov (United States)

    Zhu, Ning; Sun, Shouguang; Li, Qiang; Zou, Hua

    2016-05-01

    When a train runs at high speeds, the external exciting frequencies approach the natural frequencies of bogie critical components, thereby inducing strong elastic vibrations. The present international reliability test evaluation standard and design criteria of bogie frames are all based on the quasi-static deformation hypothesis. Structural fatigue damage generated by structural elastic vibrations has not yet been included. In this paper, theoretical research and experimental validation are done on elastic dynamic load spectra on bogie frame of high-speed train. The construction of the load series that correspond to elastic dynamic deformation modes is studied. The simplified form of the load series is obtained. A theory of simplified dynamic load-time histories is then deduced. Measured data from the Beijing-Shanghai Dedicated Passenger Line are introduced to derive the simplified dynamic load-time histories. The simplified dynamic discrete load spectra of bogie frame are established. Based on the damage consistency criterion and a genetic algorithm, damage consistency calibration of the simplified dynamic load spectra is finally performed. The computed result proves that the simplified load series is reasonable. The calibrated damage that corresponds to the elastic dynamic discrete load spectra can cover the actual damage at the operating conditions. The calibrated damage satisfies the safety requirement of damage consistency criterion for bogie frame. This research is helpful for investigating the standardized load spectra of bogie frame of high-speed train.

  3. Nodeless vibrational amplitudes and quantum nonadiabatic dynamics in the nested funnel for a pseudo Jahn-Teller molecule or homodimer

    Science.gov (United States)

    Peters, William K.; Tiwari, Vivek; Jonas, David M.

    2017-11-01

    The nonadiabatic states and dynamics are investigated for a linear vibronic coupling Hamiltonian with a static electronic splitting and weak off-diagonal Jahn-Teller coupling through a single vibration with a vibrational-electronic resonance. With a transformation of the electronic basis, this Hamiltonian is also applicable to the anti-correlated vibration in a symmetric homodimer with marginally strong constant off-diagonal coupling, where the non-adiabatic states and dynamics model electronic excitation energy transfer or self-exchange electron transfer. For parameters modeling a free-base naphthalocyanine, the nonadiabatic couplings are deeply quantum mechanical and depend on wavepacket width; scalar couplings are as important as the derivative couplings that are usually interpreted to depend on vibrational velocity in semiclassical curve crossing or surface hopping theories. A colored visualization scheme that fully characterizes the non-adiabatic states using the exact factorization is developed. The nonadiabatic states in this nested funnel have nodeless vibrational factors with strongly avoided zeroes in their vibrational probability densities. Vibronic dynamics are visualized through the vibrational coordinate dependent density of the time-dependent dipole moment in free induction decay. Vibrational motion is amplified by the nonadiabatic couplings, with asymmetric and anisotropic motions that depend upon the excitation polarization in the molecular frame and can be reversed by a change in polarization. This generates a vibrational quantum beat anisotropy in excess of 2/5. The amplitude of vibrational motion can be larger than that on the uncoupled potentials, and the electronic population transfer is maximized within one vibrational period. Most of these dynamics are missed by the adiabatic approximation, and some electronic and vibrational motions are completely suppressed by the Condon approximation of a coordinate-independent transition dipole between

  4. Geometric Properties of Grassmannian Frames for and

    Directory of Open Access Journals (Sweden)

    Benedetto John J

    2006-01-01

    Full Text Available Grassmannian frames are frames satisfying a min-max correlation criterion. We translate a geometrically intuitive approach for two- and three-dimensional Euclidean space ( and into a new analytic method which is used to classify many Grassmannian frames in this setting. The method and associated algorithm decrease the maximum frame correlation, and hence give rise to the construction of specific examples of Grassmannian frames. Many of the results are known by other techniques, and even more generally, so that this paper can be viewed as tutorial. However, our analytic method is presented with the goal of developing it to address unresovled problems in -dimensional Hilbert spaces which serve as a setting for spherical codes, erasure channel modeling, and other aspects of communications theory.

  5. An introduction to frames and Riesz bases

    CERN Document Server

    Christensen, Ole

    2016-01-01

    This revised and expanded monograph presents the general theory for frames and Riesz bases in Hilbert spaces as well as its concrete realizations within Gabor analysis, wavelet analysis, and generalized shift-invariant systems.  Compared with the first edition, more emphasis is put on explicit constructions with attractive properties.  Based on the exiting development of frame theory over the last decade, this second edition now includes new sections on the rapidly growing fields of LCA groups, generalized shift-invariant systems, duality theory for as well Gabor frames as wavelet frames, and open problems in the field.   Key features include: *Elementary introduction to frame theory in finite-dimensional spaces * Basic results presented in an accessible way for both pure and applied mathematicians * Extensive exercises make the work suitable as a textbook for use in graduate courses * Full proofs includ ed in introductory chapters; only basic knowledge of functional analysis required * Explicit constructi...

  6. Vibrational Damping of Composite Materials

    OpenAIRE

    Biggerstaff, Janet M.

    2006-01-01

    The purpose of this research was to develop new methods of vibrational damping in polymeric composite materials along with expanding the knowledge of currently used vibrational damping methods. A new barrier layer technique that dramatically increased damping in viscoelastic damping materials that interacted with the composite resin was created. A method for testing the shear strength of damping materials cocured in composites was developed. Directional damping materials, where the loss facto...

  7. Vibration Theory, Vol. 1B

    DEFF Research Database (Denmark)

    Asmussen, J. C.; Nielsen, Søren R. K.

    The present collection of MATLAB exercises has been published as a supplement to the textbook, Svingningsteori, Bind 1 and the collection of exercises in Vibration theory, Vol. 1A, Solved Problems. Throughout the exercise references are made to these books. The purpose of the MATLAB exercises...... is to give a better understanding of the physical problems in linear vibration theory and to surpress the mathematical analysis used to solve the problems. For this purpose the MATLAB environment is excellent....

  8. Harmonic vibrations of multispan beams

    DEFF Research Database (Denmark)

    Dyrbye, Claes

    1996-01-01

    Free and forced harmonic vibrations of multispan beams are determined by a method which implies 1 equation regardless of the configuration. The necessary formulas are given in the paper. For beams with simple supports and the same length of all (n) spans, there is a rather big difference between...... the n´th and the (n+1)´th eigenfrequency. The reason for this phenomenon is explained.Keywords: Vibrations, Eigenfrequencies, Beams....

  9. Smart accelerometer. [vibration damage detection

    Science.gov (United States)

    Bozeman, Richard J., Jr. (Inventor)

    1994-01-01

    The invention discloses methods and apparatus for detecting vibrations from machines which indicate an impending malfunction for the purpose of preventing additional damage and allowing for an orderly shutdown or a change in mode of operation. The method and apparatus is especially suited for reliable operation in providing thruster control data concerning unstable vibration in an electrical environment which is typically noisy and in which unrecognized ground loops may exist.

  10. Improved Predictions for Geotechnical Vibrations

    OpenAIRE

    Macijauskas, Darius

    2015-01-01

    In urban areas where the infrastructure is dense and construction of new structures is near existing and sensitive buildings, frequently vibrations, caused by human activities, occur. Generated waves in the soil may adversely affect surrounding buildings. These vibrations have to be predicted a priori by using currently available knowledge of the soil dynamics. Current research, conducted by Deltares research institute, showed that the reliability of methods for prediction of m...

  11. Stress analysis of vibrating pipelines

    Science.gov (United States)

    Zachwieja, Janusz

    2017-03-01

    The pipelines are subject to various constraints variable in time. Those vibrations, if not monitored for amplitude and frequency, may result in both the fatigue damage in the pipeline profile at high stress concentration and the damage to the pipeline supports. If the constraint forces are known, the system response may be determined with high accuracy using analytical or numerical methods. In most cases, it may be difficult to determine the constraint parameters, since the industrial pipeline vibrations occur due to the dynamic effects of the medium in the pipeline. In that case, a vibration analysis is a suitable alternative method to determine the stress strain state in the pipeline profile. Monitoring the pipeline vibration levels involves a comparison between the measured vibration parameters and the permissible values as depicted in the graphs for a specific pipeline type. Unfortunately, in most cases, the studies relate to the petrochemical industry and thus large diameter, long and straight pipelines. For a pipeline section supported on both ends, the response in any profile at the entire section length can be determined by measuring the vibration parameters at two different profiles between the pipeline supports. For a straight pipeline section, the bending moments, variable in time, at the ends of the analysed section are a source of the pipe excitation. If a straight pipe section supported on both ends is excited by the bending moments in the support profile, the starting point for the stress analysis are the strains, determined from the Euler-Bernoulli equation. In practice, it is easier to determine the displacement using the experimental methods, since the factors causing vibrations are unknown. The industrial system pipelines, unlike the transfer pipelines, are straight sections at some points only, which makes it more difficult to formulate the equation of motion. In those cases, numerical methods can be used to determine stresses using the

  12. Approximately dual frames in Hilbert spaces and applications to Gabor frames

    DEFF Research Database (Denmark)

    Christensen, Ole; Laugesen, Richard S.

    2011-01-01

    Approximately dual frames are studied in the Hilbert space setting. Approximate duals are easier to construct than classical dual frames, and can be tailored to yield almost perfect reconstruction. Bounds on the deviation from perfect reconstruction are obtained for approximately dual frames...

  13. Adjudicating Frame Shifts and Frame Disputes in the New Millennial University: The Role of the Dean

    Science.gov (United States)

    Lessor, Roberta G.

    2008-01-01

    This paper argues that sociological theory provides a sound basis for analyzing the social organization and reorganization of the college or university and for guiding the activities of the college dean. Frame analysis theory, developed in the study of social movements, and the attendant concepts of frame shifts and frame disputes, are drawn on to…

  14. Seismic response analysis of a 13-story steel moment-framed building in Alhambra, California

    Science.gov (United States)

    Rodgers, Janise E.; Sanli, Ahmet K.; Çelebi, Mehmet

    2004-01-01

    The seismic performance of steel moment-framed buildings has been of particular interest since brittle fractures were discovered at the beam-column connections of some frames following the M6.7 1994 Northridge earthquake. This report presents an investigation of the seismic behavior of an instrumented 13-story steel moment frame building located in the greater Los Angeles area of California. An extensive strong motion dataset, ambient vibration data, engineering drawings and earthquake damage reports are available for this building. The data are described and subsequently analyzed. The results of the analyses show that the building response is more complex than would be expected from its highly symmetrical geometry. The building's response is characterized by low damping in the fundamental mode, larger peak accelerations in the intermediate stories than at the roof, extended periods of vibration after the cessation of strong input shaking, beating in the response, and significant torsion during strong shaking at the top of the concrete piers which extend from the basement to the second floor. The analyses of the data and all damage detection methods employed except one method based on system identification indicate that the response of the structure was elastic in all recorded earthquakes. These findings are in general agreement with the results of intrusive inspections (meaning fireproofing and architectural finishes were removed) conducted on approximately 5 percent of the moment connections following the Northridge earthquake, which found no earthquake damage.

  15. Effect of Wheelchair Frame Material on Users’ Mechanical Work and Transmitted Vibration

    Directory of Open Access Journals (Sweden)

    Félix Chénier

    2014-01-01

    similar to aluminium wheelchairs. A negative correlation between VT and WN-WPM was found, which means that reducing VT may be at the expense of increasing WN-WPM. Based on our results, use of carbon in wheelchair construction seems promising to reduce VT without increasing WN-WPM.

  16. Vibrational modes of nanolines

    Science.gov (United States)

    Heyliger, Paul R.; Flannery, Colm M.; Johnson, Ward L.

    2008-04-01

    Brillouin-light-scattering spectra previously have been shown to provide information on acoustic modes of polymeric lines fabricated by nanoimprint lithography. Finite-element methods for modeling such modes are presented here. These methods provide a theoretical framework for determining elastic constants and dimensions of nanolines from measured spectra in the low gigahertz range. To make the calculations feasible for future incorporation in inversion algorithms, two approximations of the boundary conditions are employed in the calculations: the rigidity of the nanoline/substrate interface and sinusoidal variation of displacements along the nanoline length. The accuracy of these approximations is evaluated as a function of wavenumber and frequency. The great advantage of finite-element methods over other methods previously employed for nanolines is the ability to model any cross-sectional geometry. Dispersion curves and displacement patterns are calculated for modes of polymethyl methacrylate nanolines with cross-sectional dimensions of 65 nm × 140 nm and rectangular or semicircular tops. The vibrational displacements and dispersion curves are qualitatively similar for the two geometries and include a series of flexural, Rayleigh-like, and Sezawa-like modes. This paper is a contribution of the National Institute of Standards and Technology and is not subject to copyright in the United States.

  17. Simulation of Cross Set in Frame Structures

    Directory of Open Access Journals (Sweden)

    D. K. Dragun

    2016-01-01

    Full Text Available The paper deals with modeling methods of frame structures, used in rocket technology. To estimate their inertia, stiffness and strength properties there is a need to create its calculation model. For this purpose now a finite element method is generally used. These models may use various finite elements and combinations thereof. It is obvious that the calculation has found that parameters of the structure under study depend on the selected calculation model.The paper discusses some issues concerning the idealization of elements of the hypothetical frame structure. To simulate the element properties of a longitudinal set (stringers and longerons and struts as well is offered idealization of beam, because their crosswise dimensions are substantially smaller than the longitudinal ones. Elements of a crosswise force set (frames represent a welded plate structure that has arch-curved shape of variable cross-section with holes. Welded tubes of different diameter reinforce holes in plates. In vertical plates there are cutouts to mount stringers. To take in full into consideration these features in the rod idealization of frames is impossible. Therefore it seems more appropriate to use plate finite elements to simulate frames.The paper considers two possible frame models the to show their stiffness properties, namely a rod model and a plate one. It shows the advantages and disadvantages of given design schemes of the frame. Based on the test calculations the paper shows which errors in calculating the stiffness properties of the frame under consideration can be obtained using the rod model.  Recommendations for judicious use of possible models of the frame at different designing stages are made.To create the studied frame models and their test calculations and analyze the results of calculation was used a SADAS software package developed at the SM8 Department of BMSTU.

  18. Space Shuttle Crawler Transporter Vibration Analysis in Support of Rollout Fatigue Load Spectra Verification Program

    Science.gov (United States)

    Margasahayam, Ravi N.; Meyer, Karl A.; Nerolich, Shaun M.; Burton, Roy C.; Gosselin, Armand M.

    2004-01-01

    The Crawler Transporter (CT), designed and built for the Apollo Program in the 1960's and surpassing its initial operational life, has become an integral part of the Space Shuttle Program (SSP). The CT transports the Space Shuttle Vehicle (SSV) stack, atop the Mobile Launch Platform (MLP), from the Vehicle Assembly Building (VAB) to the launch pad. This support structure provides hydraulic jacking, leveling and load equalization for the 12 million pound stack on its 3.5-5.0 mile rollout to the launch pad. Major elements of the SSV, consisting of the orbiter, solid rocket boosters (SRB) and external tank (ET) have required fatigue analyses as part of the mission life certification. Compared to rollout vibration, the SSV sees relatively high vibration loads during launch, ascent, descent and landing phases of the mission. Although preliminary measured SRB vibration levels during rollout were of low amplitude and frequency, the duration of the rollout phase is typically high, from 5-6 hours. As part of an expanded mission life assessment, additional certification effort was initiated to define fatigue load spectra for rollout. This study addresses the CT vibration analyses in support of the rollout fatigue study. Structural models developed for modal and vibration analyses were used to identify unique CT, CT/MLP and CT/MLP/SRB vibration characteristics for comparison to instrumented rollout tests. Whereas the main structural and vibration characteristics of the SSV are well defined, minimum analytical and vibration test data on the Crawler Transporter were available. Unique vibration characteristics of the CT are attributable to the drive mechanism, hydraulic jacking system, structural framing and the CT-to-MLP support pad restraints. Initial tests performed on the CT/MLP/SRB configuration showed reasonable correlation with predicted mode shapes and frequencies.

  19. Quantitative rotating frame relaxometry methods in MRI.

    Science.gov (United States)

    Gilani, Irtiza Ali; Sepponen, Raimo

    2016-06-01

    Macromolecular degeneration and biochemical changes in tissue can be quantified using rotating frame relaxometry in MRI. It has been shown in several studies that the rotating frame longitudinal relaxation rate constant (R1ρ ) and the rotating frame transverse relaxation rate constant (R2ρ ) are sensitive biomarkers of phenomena at the cellular level. In this comprehensive review, existing MRI methods for probing the biophysical mechanisms that affect the rotating frame relaxation rates of the tissue (i.e. R1ρ and R2ρ ) are presented. Long acquisition times and high radiofrequency (RF) energy deposition into tissue during the process of spin-locking in rotating frame relaxometry are the major barriers to the establishment of these relaxation contrasts at high magnetic fields. Therefore, clinical applications of R1ρ and R2ρ MRI using on- or off-resonance RF excitation methods remain challenging. Accordingly, this review describes the theoretical and experimental approaches to the design of hard RF pulse cluster- and adiabatic RF pulse-based excitation schemes for accurate and precise measurements of R1ρ and R2ρ . The merits and drawbacks of different MRI acquisition strategies for quantitative relaxation rate measurement in the rotating frame regime are reviewed. In addition, this review summarizes current clinical applications of rotating frame MRI sequences. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

  20. A reference Pelton turbine - High speed visualization in the rotating frame

    Science.gov (United States)

    Solemslie, Bjørn W.; Dahlhaug, Ole G.

    2016-11-01

    To enable a detailed study the flow mechanisms effecting the flow within the reference Pelton runner designed at the Waterpower Laboratory (NTNLT) a flow visualization system has been developed. The system enables high speed filming of the hydraulic surface of a single bucket in the rotating frame of reference. It is built with an angular borescopes adapter entering the turbine along the rotational axis and a borescope embedded within a bucket. A stationary high speed camera located outside the turbine housing has been connected to the optical arrangement by a non-contact coupling. The view point of the system includes the whole hydraulic surface of one half of a bucket. The system has been designed to minimize the amount of vibrations and to ensure that the vibrations felt by the borescope are the same as those affecting the camera. The preliminary results captured with the system are promising and enable a detailed study of the flow within the turbine.

  1. Simple Design Tool for Development of Well Insulated Window Frames and Optimization of the Frame Geometry

    DEFF Research Database (Denmark)

    Zajas, Jan Jakub; Heiselberg, Per

    2012-01-01

    This paper describes a design tool created with the purpose of designing highly insulated window frames. The design tool is based on a parametric model of the frame geometry, where various parameters describing the frame can be easily changed by the user. Based on this input, geometry of the frame...... is generated by the program and is used by the finite element simulator to calculate the thermal performance of the frame (the U value). After the initial design is evaluated, the user can quickly modify chosen parameters and generate a new design. This process can then be repeated in multiple iterations...... in order to approach an optimal solution. The program was also used to conduct an optimization process of the frame geometry. A large number of various window frame designs were created and evaluated, based on their insulation properties. The paper presents the investigation process and some of the best...

  2. The role of message framing in promoting MMR vaccination: evidence of a loss-frame advantage.

    Science.gov (United States)

    Abhyankar, Purva; O'Connor, Daryl B; Lawton, Rebecca

    2008-01-01

    This study examined the effects of message framing on intentions to obtain the measles, mumps and rubella (MMR) vaccine for one's child and investigated whether Theory of Planned Behaviour (TPB) and perceived outcome efficacy variables mediate and/or moderate message framing effects. One hundred and forty women read either a loss-framed or gain-framed message and then completed measures assessing their intentions to obtain the MMR vaccine for their child, and TPB and outcome efficacy variables. Exposure to the loss frame increased intentions to obtain the MMR vaccine and influenced perceptions of outcome efficacy. This suggests that outcome efficacy, but not other TPB variables may mediate framing effects within the context of MMR vaccination. Message frame, in addition to TPB variables, significantly predicted unique variance in behavioural intentions. These findings are discussed within the context of Prospect Theory, perceived risk and prevention/detection behaviours.

  3. Evaluation of hand-arm vibration reducing effect of anti-vibration glove

    OpenAIRE

    樹野, 淳也; 前田, 節雄; 横田, 和樹; 平, 雄一郎

    2015-01-01

    Many kinds of the anti-vibration glove have been developed for reducing hand-arm vibration during the operation with vibration tools. International standard ISO 10819 evaluates the physical effect of gloves' vibration transmissibility but not evaluates the physiological effect of human hands. Thus, in this paper, we proposed the evaluation using the temporary threshold shift of vibrotactile perception threshold to evaluate the hand-arm vibration reducing effect of anti-vibration glove. We per...

  4. High Speed Frame Synchronization and Viterbi Decoding

    DEFF Research Database (Denmark)

    Paaske, Erik; Justesen, Jørn; Larsen, Knud J.

    1996-01-01

    The purpose of Phase 1 of the study is to describe the system structure and algorithms in sufficient detail to allow drawing the high level architecture of units containing frame synchronization and Viterbi decoding. The systems we consider are high data rate space communication systems. Also...... components. Node synchronization performed within a Viterbi decoder is discussed, and algorithms for frame synchronization are described and analyzed. We present a list of system configurations that we find potentially useful. Further, the high level architecture of units that contain frame synchronization...

  5. Framing of regimes and transition strategies

    DEFF Research Database (Denmark)

    Jensen, Jens Stissing

    2012-01-01

    This article suggests that transition strategies are always formulated in the context of specific representations of the regime and the challenges it faces. It is argued that the framing of a regime affects the envisioning of transition strategies. An analysis of the current development agenda...... for the housing construction sector in Denmark reveals the relevance and impacts of different regime framings. It is proposed that the ability to cope with framing issues as situated and political processes is at the core of the governance of transitions....

  6. Self-aligning biaxial load frame

    Science.gov (United States)

    Ward, M.B.; Epstein, J.S.; Lloyd, W.R.

    1994-01-18

    An self-aligning biaxial loading apparatus for use in testing the strength of specimens while maintaining a constant specimen centroid during the loading operation. The self-aligning biaxial loading apparatus consists of a load frame and two load assemblies for imparting two independent perpendicular forces upon a test specimen. The constant test specimen centroid is maintained by providing elements for linear motion of the load frame relative to a fixed cross head, and by alignment and linear motion elements of one load assembly relative to the load frame. 3 figures.

  7. Membrane Vibration Analysis Above the Nyquist Limit with Fluorescence Videogrammetry

    Science.gov (United States)

    Dorrington, Adrian A.; Jones, Thomas W.; Danehy, Paul M.; Pappa, Richard S.

    2004-01-01

    A new method for generating photogrammetric targets by projecting an array of laser beams onto a membrane doped with fluorescent laser dye has recently been developed. In this paper we review this new fluorescence based technique, then proceed to show how it can be used for dynamic measurements, and how a short pulsed (10 ns) laser allows the measurement of vibration modes at frequencies several times the sampling frequency. In addition, we present experimental results showing the determination of fundamental and harmonic vibration modes of a drum style dye-doped polymer membrane tautly mounted on a 12-inch circular hoop and excited with 30 Hz and 62 Hz sinusoidal acoustic waves. The projected laser dot pattern was generated by passing the beam from a pulsed Nd:YAG laser though a diffractive optical element, and the resulting fluorescence was imaged with three digital video cameras, all of which were synchronized with a pulse and delay generator. Although the video cameras are capable of 240 Hz frame rates, the laser s output was limited to 30 Hz and below. Consequently, aliasing techniques were used to allow the measurement of vibration modes up to 186 Hz with a Nyquist limit of less than 15 Hz.

  8. The Nonlinear Behavior of Vibrational Conveyers with Single-Mass Crank-and-Rod Exciters

    Directory of Open Access Journals (Sweden)

    G. Füsun Alışverişçi

    2012-01-01

    Full Text Available The single-mass, crank-and-rod exciters vibrational conveyers have a trough supported on elastic stands which are rigidly fastened to the trough and a supporting frame. The trough is oscillated by a common crank drive. This vibration causes the load to move forward and upward. The moving loads jump periodically and move forward with relatively small vibration. The movement is strictly related to vibrational parameters. This is applicable in laboratory conditions in the industry which accommodate a few grams of loads, up to those that accommodate tons of loading capacity. In this study I explore the transitional behavior across resonance, during the starting of a single degree of freedom vibratory system excited by crank-and-rod. A loaded vibratory conveyor is more safe to start than an empty one. Vibrational conveyers with cubic nonlinear spring and ideal vibration exciter have been analyzed analytically for primary and secondary resonance by the Method of Multiple Scales, and numerically. The approximate analytical results obtained in this study have been compared with the numerical results and have been found to be well matched.

  9. SEISMIC RESPONSE OF FRAME BUILDINGS WITH COMBINED EARTHQUAKE PROTECTION SYSTEM

    Directory of Open Access Journals (Sweden)

    Abakar J. Abakarov

    2017-01-01

    Full Text Available Abstract. Objectives The aim of the study is to search for methods to improve the efficiency of the earthquake protection systems with rubber-metallic seismic insulating supports by combining them with dry friction and brittle uncoupling elements. Method The research is based on dynamic modelling methods. Results The computational dynamic model of the combined earthquake protection system and the system of differential equations of the seismic motion of a five-story frame building were compiled and an algorithm for estimating the efficiency and selection of the optimum parameters of the earthquake protection system was developed. Horizontal shifting seismic forces, maximum mass movements and maximum movements of rubber-metallic seismic insulating supports at different intensities and prevailing periods of seismic soil oscillations were determined. It is shown that, by using a combined earthquake protection system, seismic loads on frame buildings can be reduced by a factor of 1.5-2 and maximum mass movements – by 4-5 times. In addition, the area of rational application of seismic isolation systems with rubber-metallic supports in relation to the prevailing periods of seismic ground oscillations is expanding substantially. Conclusion The combined earthquake protection system allows the area of effective use of rubber-metallic supports to be expanded by increasing the range of possible prevailing periods of seismic soil vibrations at which the maximum movement of the top of the rubber-metallic supports does not exceed the maximum allowable value. The maximum residual movements of rubber-metallic supports can be reduced by using a lead core. 

  10. Design of mechanical metamaterials for simultaneous vibration isolation and energy harvesting

    Science.gov (United States)

    Li, Ying; Baker, Evan; Reissman, Timothy; Sun, Cheng; Liu, Wing Kam

    2017-12-01

    Through finite element analysis and a 3D printing assisted experimental study, we demonstrate a design of mechanical metamaterials for simultaneous mechanical wave filtering and energy harvesting. The mechanical metamaterials compromise a square array of free-standing cantilevers featuring piezoelectric properties being attached to a primary structural frame. A complete bandgap has thus been created via the strong coupling of the bulk elastic wave propagating along the structural frame and the distributed local resonance associated with the square array of piezoelectrically active cantilevers. Operating within the stop-band, external vibration energy has been trapped and transferred into the kinetic energy of the cantilevers, which is further converted into electric energy through mechano-electrical conversion of its integrated piezoelectric elements. Therefore, two distinct functions, vibration isolation and energy harvesting, are achieved simultaneously through the designed mechanical metamaterials.

  11. Adaptive tight frame based multiplicative noise removal

    National Research Council Canada - National Science Library

    Weifeng Zhou; Shuguo Yang; Caiming Zhang; Shujun Fu

    2016-01-01

    .... However, it is impossible for a fixed system to be always optimal for all the images. In this paper, we present an adaptive wavelet tight frame technology for sparse representation of an image with multiplicative noise...

  12. Adaptive tight frame based multiplicative noise removal

    National Research Council Canada - National Science Library

    Allikalt, Anni; Zhou, Weifeng; Rinken, Ago; Yang, Shuguo; Zhang, Caiming; Fu, Shujun

    .... However, it is impossible for a fixed system to be always optimal for all the images. In this paper, we present an adaptive wavelet tight frame technology for sparse representation of an image with multiplicative noise...

  13. Aerial Photo - Single Frame Records - CS

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — The Aerial Photography Single Frame Records collection is a large and diverse group of imagery acquired by Federal organizations from 1937 to the present. Over 6.4...

  14. News Media Framing of Negative Campaigning

    DEFF Research Database (Denmark)

    Pedersen, Rasmus Tue

    2014-01-01

    News media coverage of election campaigns is often characterized by use of the strategic game frame and a focus on politicians’ use of negative campaigning. However, the exact relationship between these two characteristics of news coverage is largely unexplored. This article theorizes that consumer...... demand and norms of journalistic independence might induce the news media outlets to cover negative campaigning with a strategic game frame. A comprehensive content analysis based on several newspaper types, several election campaigns, and several different measurements of media framing confirms...... that news coverage of negative campaigning does apply the strategic game frame to a significantly larger degree than articles covering positive campaigning. This finding has significant implications for campaigning politicians and for scholars studying campaign and media effects....

  15. Covariance and the hierarchy of frame bundles

    Science.gov (United States)

    Estabrook, Frank B.

    1987-01-01

    This is an essay on the general concept of covariance, and its connection with the structure of the nested set of higher frame bundles over a differentiable manifold. Examples of covariant geometric objects include not only linear tensor fields, densities and forms, but affinity fields, sectors and sector forms, higher order frame fields, etc., often having nonlinear transformation rules and Lie derivatives. The intrinsic, or invariant, sets of forms that arise on frame bundles satisfy the graded Cartan-Maurer structure equations of an infinite Lie algebra. Reduction of these gives invariant structure equations for Lie pseudogroups, and for G-structures of various orders. Some new results are introduced for prolongation of structure equations, and for treatment of Riemannian geometry with higher-order moving frames. The use of invariant form equations for nonlinear field physics is implicitly advocated.

  16. Quantization Noise Shaping on Arbitrary Frame Expansions

    Directory of Open Access Journals (Sweden)

    Boufounos Petros T

    2006-01-01

    Full Text Available Quantization noise shaping is commonly used in oversampled A/D and D/A converters with uniform sampling. This paper considers quantization noise shaping for arbitrary finite frame expansions based on generalizing the view of first-order classical oversampled noise shaping as a compensation of the quantization error through projections. Two levels of generalization are developed, one a special case of the other, and two different cost models are proposed to evaluate the quantizer structures. Within our framework, the synthesis frame vectors are assumed given, and the computational complexity is in the initial determination of frame vector ordering, carried out off-line as part of the quantizer design. We consider the extension of the results to infinite shift-invariant frames and consider in particular filtering and oversampled filter banks.

  17. Gabor frames by sampling and periodization

    DEFF Research Database (Denmark)

    Søndergaard, Peter Lempel

    2007-01-01

    By sampling the window of Gabor frame for L-2 (R) belonging to Feichtingers algebra S-0 (R), one obtains a Gabor frame for l(2) (Z). In this article we present a survey of results by R. Orr and A.J.E.M. Janssen and extend their ideas to cover interrelations among Gabor frames for the four spaces L......-2 (R), l(2) (Z), L-2 ([O,L]) and C-L. Some new results about the general dual windows with respect to sampling and periodization are presented as well. This theory is used to show a new result of the Kaiblinger type to construct an approximation to the canonical dual window of a Gabor frame for L-2...

  18. Approximation of the inverse G-frame operator

    Indian Academy of Sciences (India)

    In this paper, we introduce the concept of (strong) projection method for -frames which works for all conditional -Riesz frames. We also derive a method for approximation of the inverse -frame operator which is efficient for all -frames. We show how the inverse of -frame operator can be approximated as close as we ...

  19. Figurative framing : Shaping public discourse through metaphor, hyperbole and irony

    NARCIS (Netherlands)

    Burgers, C.; Konijn, E.A.; Steen, G.J.

    2016-01-01

    Framing is an important concept in communication, yet many framing studies set out to develop frames relevant to only one issue. We expand framing theory by introducing figurative framing. We posit that figurative language types like metaphor, hyperbole and irony are important in shaping public

  20. Figurative framing: Shaping public discourse through metaphor, hyperbole and irony

    NARCIS (Netherlands)

    Burgers, C.F.; Konijn, E.A.; Steen, G.J.

    2016-01-01

    Framing is an important concept in communication, yet many framing studies set out to develop frames relevant to only one issue. We expand framing theory by introducing figurative framing. We posit that figurative language types like metaphor, hyperbole and irony are important in shaping public

  1. High Performance Commercial Fenestration Framing Systems

    Energy Technology Data Exchange (ETDEWEB)

    Mike Manteghi; Sneh Kumar; Joshua Early; Bhaskar Adusumalli

    2010-01-31

    A major objective of the U.S. Department of Energy is to have a zero energy commercial building by the year 2025. Windows have a major influence on the energy performance of the building envelope as they control over 55% of building energy load, and represent one important area where technologies can be developed to save energy. Aluminum framing systems are used in over 80% of commercial fenestration products (i.e. windows, curtain walls, store fronts, etc.). Aluminum framing systems are often required in commercial buildings because of their inherent good structural properties and long service life, which is required from commercial and architectural frames. At the same time, they are lightweight and durable, requiring very little maintenance, and offer design flexibility. An additional benefit of aluminum framing systems is their relatively low cost and easy manufacturability. Aluminum, being an easily recyclable material, also offers sustainable features. However, from energy efficiency point of view, aluminum frames have lower thermal performance due to the very high thermal conductivity of aluminum. Fenestration systems constructed of aluminum alloys therefore have lower performance in terms of being effective barrier to energy transfer (heat loss or gain). Despite the lower energy performance, aluminum is the choice material for commercial framing systems and dominates the commercial/architectural fenestration market because of the reasons mentioned above. In addition, there is no other cost effective and energy efficient replacement material available to take place of aluminum in the commercial/architectural market. Hence it is imperative to improve the performance of aluminum framing system to improve the energy performance of commercial fenestration system and in turn reduce the energy consumption of commercial building and achieve zero energy building by 2025. The objective of this project was to develop high performance, energy efficient commercial

  2. Physics within a quantum reference frame

    Energy Technology Data Exchange (ETDEWEB)

    Angelo, Renato M [Federal University of Parana, PO Box 19044, 81531-990, Curitiba, PR (Brazil); Brunner, Nicolas; Popescu, Sandu; Skrzypczyk, Paul [H H Wills Physics Laboratory, University of Bristol, Tyndall Avenue, Bristol, BS8 1TL (United Kingdom); Short, Anthony J, E-mail: renato@fisica.ufpr.br [DAMTP, Centre for Mathematical Sciences, Wilberforce Road, Cambridge, CB3 0WA (United Kingdom)

    2011-04-08

    We investigate the physics of quantum reference frames. Specifically, we study several simple scenarios involving a small number of quantum particles, whereby we promote one of these particles to the role of a quantum observer and ask what is the description of the rest of the system, as seen by this observer? We highlight the interesting aspects of such questions by presenting a number of apparent paradoxes. By unravelling these paradoxes, we obtain a better understanding of the physics of quantum reference frames.

  3. MCP gated x-ray framing camera

    Science.gov (United States)

    Cai, Houzhi; Liu, Jinyuan; Niu, Lihong; Liao, Hua; Zhou, Junlan

    2009-11-01

    A four-frame gated microchannel plate (MCP) camera is described in this article. Each frame photocathode coated with gold on the MCP is part of a transmission line with open circuit end driven by the gating electrical pulse. The gating pulse is 230 ps in width and 2.5 kV in amplitude. The camera is tested by illuminating its photocathode with ultraviolet laser pulses, 266 nm in wavelength, which shows exposure time as short as 80 ps.

  4. Ultrasonic metal welding with a vibration source using longitudinal and torsional vibration transducers

    Science.gov (United States)

    Asami, Takuya; Tamada, Yosuke; Higuchi, Yusuke; Miura, Hikaru

    2017-07-01

    Conventional ultrasonic metal welding for joining dissimilar metals uses a linear vibration locus, although this method suffers from problems such as low overall weld strength. Our previous studies have shown that ultrasonic welding with a planar vibration locus improves the weld strength. However, the vibration source in our previous studies had problems in longitudinal-torsional vibration controllability and small welding tip. Therefore, the study of the optimal shape of the vibration locus was difficult. Furthermore, improvement of weld strength cannot be expected. We have developed a new ultrasonic vibration source that can control the longitudinal-torsional vibration and can connect to a large welding tip. In this study, we clarified the longitudinal-torsional vibration controllability of the developed ultrasonic vibration source. Moreover, we clarified that using the planar locus of the developed vibration source produced a higher weld strength than our previous studies, and clarified the optimal shape of the vibration locus.

  5. Framing Integration – from Welfare to Citizenship

    Directory of Open Access Journals (Sweden)

    Ragnhild Ihle

    2014-03-01

    Full Text Available This article will study the contested concept of integration in Norway through a frame analysis approach. The aim is to study different understandings of the term "integration" as it is presented in a select body of policy documents in Norway. The methodology involved is to search in the documents and in relevant research for various interpretations of the concept, and relate them to diagnostic framing, prognostic framing and motivational framing. This method is associated with both critical frame analysis and genealogy. The analysis defines a timeline, from 1975 forward, of six concepts of integration: 1 individuals in need, care and clientification; 2 preservation of culture - a tribute to colourful community; 3 the upheaval of living conditions in specific social groups; 4 absence of structural barriers, racism and discrimination; 5 living conditions, identity and belonging; 6 Influence, participation and activation. The frames related to these concepts will expose conceptual prejudices, detect inconsistencies, challenge generalisations, and give visibility to the processes of exclusion.

  6. Mechanical Vibrations Modeling and Measurement

    CERN Document Server

    Schmitz, Tony L

    2012-01-01

    Mechanical Vibrations:Modeling and Measurement describes essential concepts in vibration analysis of mechanical systems. It incorporates the required mathematics, experimental techniques, fundamentals of modal analysis, and beam theory into a unified framework that is written to be accessible to undergraduate students,researchers, and practicing engineers. To unify the various concepts, a single experimental platform is used throughout the text to provide experimental data and evaluation. Engineering drawings for the platform are included in an appendix. Additionally, MATLAB programming solutions are integrated into the content throughout the text. This book also: Discusses model development using frequency response function measurements Presents a clear connection between continuous beam models and finite degree of freedom models Includes MATLAB code to support numerical examples that are integrated into the text narrative Uses mathematics to support vibrations theory and emphasizes the practical significanc...

  7. DOWNHOLE VIBRATION MONITORING & CONTROL SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Martin E. Cobern

    2004-08-31

    The deep hard rock drilling environment induces severe vibrations into the drillstring, which can cause reduced rates of penetration (ROP) and premature failure of the equipment. The only current means of controlling vibration under varying conditions is to change either the rotary speed or the weight-on-bit (WOB). These changes often reduce drilling efficiency. Conventional shock subs are useful in some situations, but often exacerbate the problems. The objective of this project is development of a unique system to monitor and control drilling vibrations in a ''smart'' drilling system. This system has two primary elements: (1) The first is an active vibration damper (AVD) to minimize harmful axial, lateral and torsional vibrations. The hardness of this damper will be continuously adjusted using a robust, fast-acting and reliable unique technology. (2) The second is a real-time system to monitor drillstring vibration, and related parameters. This monitor adjusts the damper according to local conditions. In some configurations, it may also send diagnostic information to the surface via real-time telemetry. The AVD is implemented in a configuration using magnetorheological (MR) fluid. By applying a current to the magnetic coils in the damper, the viscosity of the fluid can be changed rapidly, thereby altering the damping coefficient in response to the measured motion of the tool. Phase I of this program entailed modeling and design of the necessary subsystems and design, manufacture and test of a full laboratory prototype. Phase I of the project was completed by the revised end date of May 31, 2004. The objectives of this phase were met, and all prerequisites for Phase II have been completed.

  8. DOWNHOLE VIBRATION MONITORING & CONTROL SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Martin E. Cobern

    2004-10-13

    The deep hard rock drilling environment induces severe vibrations into the drillstring, which can cause reduced rates of penetration (ROP) and premature failure of the equipment. The only current means of controlling vibration under varying conditions is to change either the rotary speed or the weight-on-bit (WOB). These changes often reduce drilling efficiency. Conventional shock subs are useful in some situations, but often exacerbate the problems. The objective of this project is development of a unique system to monitor and control drilling vibrations in a ''smart'' drilling system. This system has two primary elements: (1) The first is an active vibration damper (AVD) to minimize harmful axial, lateral and torsional vibrations. The hardness of this damper will be continuously adjusted using a robust, fast-acting and reliable unique technology. (2) The second is a real-time system to monitor drillstring vibration, and related parameters. This monitor adjusts the damper according to local conditions. In some configurations, it may also send diagnostic information to the surface via real-time telemetry. The AVD is implemented in a configuration using magnetorheological (MR) fluid. By applying a current to the magnetic coils in the damper, the viscosity of the fluid can be changed rapidly, thereby altering the damping coefficient in response to the measured motion of the tool. Phase I of this program entailed modeling and design of the necessary subsystems and design, manufacture and test of a full laboratory prototype. Phase I of the project was completed by the revised end date of May 31, 2004. The objectives of this phase were met, and all prerequisites for Phase II have been completed. The month of June, 2004 was primarily occupied with the writing of the Phase I Final Report, the sole deliverable of Phase I, which will be submitted in the next quarter. Redesign of the laboratory prototype and design of the downhole (Phase II) prototype was

  9. Vibrational Collapse of Hexapod Packings

    Science.gov (United States)

    Zhao, Yuchen; Ding, Jingqiu; Barés, Jonathan; Zheng, Hu; Dierichs, Karola; Menges, Achim; Behringer, Robert

    2017-06-01

    Columns made of convex noncohesive grains like sand collapse after being released from a confining container. However, structures built from non-convex grains can be stable without external support. In the current experiments, we investigate the effect of vibration on destroying such columns. The change of column height during vertical vibration, can be well characterized by stretched exponential relaxation when the column is short, which is in agreement with previous work, while a faster collapse happens when the column is tall. We investigate the collapse after the fast process including its dependence on column geometry, and on interparticle and basal friction.

  10. Innovative Techniques Simplify Vibration Analysis

    Science.gov (United States)

    2010-01-01

    In the early years of development, Marshall Space Flight Center engineers encountered challenges related to components in the space shuttle main engine. To assess the problems, they evaluated the effects of vibration and oscillation. To enhance the method of vibration signal analysis, Marshall awarded Small Business Innovation Research (SBIR) contracts to AI Signal Research, Inc. (ASRI), in Huntsville, Alabama. ASRI developed a software package called PC-SIGNAL that NASA now employs on a daily basis, and in 2009, the PKP-Module won Marshall s Software of the Year award. The technology is also used in many industries: aircraft and helicopter, rocket engine manufacturing, transportation, and nuclear power."

  11. Investigation into the vibration of metro bogies induced by rail corrugation

    Science.gov (United States)

    Ling, Liang; Li, Wei; Foo, Elbert; Wu, Lei; Wen, Zefeng; Jin, Xuesong

    2017-01-01

    The current research of rail corrugation mainly focuses on the mechanisms of its formation and development. Compared with the root causes and development mechanisms, the wheel-rail impacts, the fatigue failure of vehicle-track parts, and the loss of ride comfort due to rail corrugation should also be taken into account. However, the influences of rail corrugation on vehicle and track vibration, and failure of vehicle and track structural parts are barely discussed in the literature. This paper presents an experimental and numerical investigation of the structural vibration of metro bogies caused by rail corrugation. Extensive experiments are conducted to investigate the effects of short-pitch rail corrugation on the vibration accelerations of metro bogies. A dynamic model of a metro vehicle coupled with a concrete track is established to study the influence of rail corrugation on the structural vibration of metro bogies. The field test results indicate that the short-pitch rail corrugation generates strong vibrations on the axle-boxes and the bogie frames, therefore, accelerates the fatigue failure of the bogie components. The numerical results show that short-pitch rail corrugation may largely reduce the fatigue life of the coil spring, and improving the damping value of the primary vertical dampers is likely to reduce the strong vibration induced by short-pitch rail corrugation. This research systematically studies the effect of rail corrugation on the vibration of metro bogies and proposes some remedies for mitigating strong vibrations of metro bogies and reducing the incidence of failure in primary coil springs, which would be helpful in developing new metro bogies and track maintenance procedures.

  12. Vibration Study of Fork-lift Truck Based on the Virtual Prototype Technology

    Directory of Open Access Journals (Sweden)

    YANG Mingliang

    2014-05-01

    Full Text Available The forklift truck is one of important equipments of the modern logistics system. As the forklift truck is running, the driver seat and steering wheel of a certain type of fork-lift truck vibrate strongly, virtual prototyping technology and multi-body dynamics are used to make simulation of dynamic performance of fork-lift truck in this paper, and then the test result is compared with time course load that obtained from frame junction with the annex. We should repeatedly modify the simulation model based on test results, which is consistent with the actual results. Based on this model, so we put forward measures for improving design: Firstly, the axis of rotation of oval steering axle is implied; Secondly, the overhead guard is connected with the frame by the rubber cushion blocks at four different locations; Thirdly, the engine is fixed on the frame by the rubber cushion blocks (shock mount in two different position. The improved simulation and experimental verification are carried out under the same conditions, and the results show that the fundamental frequency of seat of the improved fork-lift truck and vibration energy are lower. The result proves the practical value of this method in the research of the vibration characteristics of complete engineering machine.

  13. Eckart ro-vibrational Hamiltonians via the gateway Hamilton operator: Theory and practice

    Science.gov (United States)

    Szalay, Viktor

    2017-03-01

    Recently, a general expression for Eckart-frame Hamilton operators has been obtained by the gateway Hamiltonian method [V. Szalay, J. Chem. Phys. 142, 174107 (2015) and V. Szalay, J. Chem. Phys. 143, 064104 (2015)]. The kinetic energy operator in this general Hamiltonian is nearly identical to that of the Eckart-Watson operator even when curvilinear vibrational coordinates are employed. Its different realizations correspond to different methods of calculating Eckart displacements. There are at least two different methods for calculating such displacements: rotation and projection. In this communication, the application of Eckart Hamiltonian operators constructed by rotation and projection, respectively, is numerically demonstrated in calculating vibrational energy levels. The numerical examples confirm that there is no need for rotation to construct an Eckart ro-vibrational Hamiltonian. The application of the gateway method is advantageous even when rotation is used since it obviates the need for differentiation of the matrix rotating into the Eckart frame. Simple geometrical arguments explain that there are infinitely many different methods for calculating Eckart displacements. The geometrical picture also suggests that a unique Eckart displacement vector may be defined as the shortest (mass-weighted) Eckart displacement vector among Eckart displacement vectors corresponding to configurations related by rotation. Its length, as shown analytically and demonstrated by numerical examples, is equal to or less than that of the Eckart displacement vector one can obtain by rotation to the Eckart frame.

  14. Eckart ro-vibrational Hamiltonians via the gateway Hamilton operator: Theory and practice.

    Science.gov (United States)

    Szalay, Viktor

    2017-03-28

    Recently, a general expression for Eckart-frame Hamilton operators has been obtained by the gateway Hamiltonian method [V. Szalay, J. Chem. Phys. 142, 174107 (2015) and V. Szalay, J. Chem. Phys. 143, 064104 (2015)]. The kinetic energy operator in this general Hamiltonian is nearly identical to that of the Eckart-Watson operator even when curvilinear vibrational coordinates are employed. Its different realizations correspond to different methods of calculating Eckart displacements. There are at least two different methods for calculating such displacements: rotation and projection. In this communication, the application of Eckart Hamiltonian operators constructed by rotation and projection, respectively, is numerically demonstrated in calculating vibrational energy levels. The numerical examples confirm that there is no need for rotation to construct an Eckart ro-vibrational Hamiltonian. The application of the gateway method is advantageous even when rotation is used since it obviates the need for differentiation of the matrix rotating into the Eckart frame. Simple geometrical arguments explain that there are infinitely many different methods for calculating Eckart displacements. The geometrical picture also suggests that a unique Eckart displacement vector may be defined as the shortest (mass-weighted) Eckart displacement vector among Eckart displacement vectors corresponding to configurations related by rotation. Its length, as shown analytically and demonstrated by numerical examples, is equal to or less than that of the Eckart displacement vector one can obtain by rotation to the Eckart frame.

  15. Dynamic Vibration Analysis of Heavy Vehicle Truck Transmission Gearbox Housing Using FEA

    Directory of Open Access Journals (Sweden)

    Ashwani Kumar

    2014-09-01

    Full Text Available The main objective of this original research article is to study the loose fixture mounting affect of heavy vehicle transmission gearbox housing. The studies were completed in three phases. In first phase the aim was to find the actual suitable boundary condition. After finding the boundary condition in second phase the fixture bolts were loosened to monitor the affect of looseness and in third phase the positional looseness based study were completed. The looseness of transmission housing causes heavy vibration and noise. In order to prevent this noise and vibration the transmission housing is tightly mounted on the chassis frame using bolts. In our design transmission housing is constraint on chassis frame using 37 bolts. Truck transmission system determines the level of noise together with the chassis, engine and bodywork. Vehicle transmissions under torsional vibration condition caused rattling and clattering noises. Reciprocity Principle was used to determine the failure frequencies for transmission housing. In reciprocity principle gear and shafts are suppressed and all the forces transmitted through the bearings are applied on the empty housing. FEA based ANSYS 14.5 has been used as analysis tool. The free vibration frequency for zero displacement condition varies from 1669 Hz to 2865 Hz and for loose transmission casing frequency varies from 1311 Hz to 3110 Hz. The analysis have theoretical and practical aspects and useful for transmission housing structure optimization.

  16. A short introduction to frames, Gabor systems, and wavelet systems

    DEFF Research Database (Denmark)

    Christensen, Ole

    2014-01-01

    In this article we present a short survey of frame theory in Hilbert spaces. We discuss Gabor frames and wavelet frames, and a recent transform that allows to move results from one setting into the other and vice versa.......In this article we present a short survey of frame theory in Hilbert spaces. We discuss Gabor frames and wavelet frames, and a recent transform that allows to move results from one setting into the other and vice versa....

  17. Sub-Frame Crossing for Streaming Video over Wireless Networks

    OpenAIRE

    Aziz, Hussein Muzahim; Grahn, Håkan; Lundberg, Lars

    2010-01-01

    Transmitting a real time video streaming over a wireless network cannot guarantee that all the frames could be received by the mobile devices. The characteristics of a wireless network in terms of the available bandwidth, frame delay, and frame losses cannot be known in advanced. In this work, we propose a new mechanism for streaming video over a wireless channel. The proposed mechanism prevents freezing frames in the mobile devices. This is done by splitting the video frame in two sub-frames...

  18. Framing-effects approach: A theoretical and methodological critique

    OpenAIRE

    Scheufele, Bertram

    2004-01-01

    The article deals with research on framing effects. First, I will start with classifying different approaches on framing. Subsequently, I will provide a definition of the concepts of frame, schema and framing, expand on framing research conducted so far - both theoretically and operationally. Having this equipment at hand, I will initiate a discussion on studies of framing-effects in terms of theory, methods and empirical results. This discussion leads to the conclusion that studies on framin...

  19. Energetics, structures, vibrational frequencies, vibrational absorption, vibrational circular dichroism and Raman intensities of Leu-enkephalin

    DEFF Research Database (Denmark)

    Jalkanen, Karl J.

    2003-01-01

    Here we present several low energy conformers of Leu-enkephalin (LeuE) calculated with the density functional theory using the Becke 3LYP hybrid functional and the 6-31G* basis set. The structures, conformational energies, vibrational frequencies, vibrational absorption (VA) intensities......, vibrational circular dichroism (VCD) intensities and Raman scattering intensities are reported for the conformers of LeuE which are expected to be populated at room temperature. The species of LeuE-present in non-polar solvents is the neutral non-ionic species with the NH2 and CO2H groups, in contrast...... to the zwitterionic neutral species with the NH3+ and CO2- groups which predominates in aqueous solution and in the crystal. All of our attempts to find the zwitterionic species in the isolated state failed, with the result that a hydrogen atom from the positively charged N-terminus ammonium group transferred either...

  20. Resonant vibration control of rotating beams

    DEFF Research Database (Denmark)

    Svendsen, Martin Nymann; Krenk, Steen; Høgsberg, Jan Becker

    2011-01-01

    Rotatingstructures,like e.g.wind turbine blades, may be prone to vibrations associated with particular modes of vibration. It is demonstrated, how this type of vibrations can be reduced by using a collocated sensor–actuator system, governed by a resonant controller. The theory is here demonstrated...... modal connectivity, only very limited modal spill-over is generated. The controller acts by resonance and therefore has only a moderate energy consumption, and successfully reduces modal vibrations at the resonance frequency....

  1. Low-energy isovector quadrupole vibrations

    Energy Technology Data Exchange (ETDEWEB)

    Faessler, A.; Nojarov, R.

    1986-01-23

    The low-lying isovector quadrupole vibrations are described by an extension of the vibrational model allowing independent proton and neutron vibrations coupled by the symmetry energy. The recently detected low-lying isovector states in nearly spherical nuclei with N=84 are described well concerning their energies and E2/M1 mixing ratios. (orig.).

  2. Ground Vibration Measurements at LHC Point 4

    Energy Technology Data Exchange (ETDEWEB)

    Bertsche, Kirk; /SLAC; Gaddi, Andrea; /CERN

    2012-09-17

    Ground vibration was measured at Large Hadron Collider (LHC) Point 4 during the winter shutdown in February 2012. This report contains the results, including power and coherence spectra. We plan to collect and analyze vibration data from representative collider halls to inform specifications for future linear colliders, such as ILC and CLIC. We are especially interested in vibration correlations between final focus lens locations.

  3. Rotor Vibration Reduction via Active Hybrid Bearings

    DEFF Research Database (Denmark)

    Nicoletti, Rodrigo; Santos, Ilmar

    2002-01-01

    The use of fluid power to reduce and control rotor vibration in rotating machines is investigated. An active hybrid bearing is studied, whose main objective is to reduce wear and vibration between rotating and stationary machinery parts. By injecting pressurised oil into the oil film, through...... with experiment, and simulations show the feasibility of controlling shaft vibration through this active device....

  4. 33 CFR 159.103 - Vibration test.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Vibration test. 159.103 Section...) POLLUTION MARINE SANITATION DEVICES Design, Construction, and Testing § 159.103 Vibration test. The device... subjected to a sinusoidal vibration for a period of 12 hours, 4 hours in each of the x, y, and z planes, at...

  5. 14 CFR 27.907 - Engine vibration.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Engine vibration. 27.907 Section 27.907... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant General § 27.907 Engine vibration. (a) Each engine must be installed to prevent the harmful vibration of any part of the engine or rotorcraft. (b) The addition of the...

  6. 14 CFR 29.251 - Vibration.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Vibration. 29.251 Section 29.251... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Miscellaneous Flight Requirements § 29.251 Vibration. Each part of the rotorcraft must be free from excessive vibration under each appropriate speed and power...

  7. 14 CFR 29.907 - Engine vibration.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Engine vibration. 29.907 Section 29.907... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant General § 29.907 Engine vibration. (a) Each engine must be installed to prevent the harmful vibration of any part of the engine or rotorcraft. (b) The...

  8. 14 CFR 27.251 - Vibration.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Vibration. 27.251 Section 27.251... STANDARDS: NORMAL CATEGORY ROTORCRAFT Flight Miscellaneous Flight Requirements § 27.251 Vibration. Each part of the rotorcraft must be free from excessive vibration under each appropriate speed and power...

  9. 49 CFR 178.608 - Vibration standard.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Vibration standard. 178.608 Section 178.608... Testing of Non-bulk Packagings and Packages § 178.608 Vibration standard. (a) Each packaging must be capable of withstanding, without rupture or leakage, the vibration test procedure outlined in this section...

  10. 49 CFR 178.985 - Vibration test.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Vibration test. 178.985 Section 178.985... Testing of Large Packagings § 178.985 Vibration test. (a) General. All rigid Large Packaging and flexible Large Packaging design types must be capable of withstanding the vibration test. (b) Test method. (1) A...

  11. Vibrations in a moving flexible robot arm

    Science.gov (United States)

    Wang, P. K. C.; Wei, Jin-Duo

    1987-01-01

    The vibration in a flexible robot arm modeled by a moving slender prismatic beam is considered. It is found that the extending and contracting motions have destabilizing and stabilizing effects on the vibratory motions, respectively. The vibration analysis is based on a Galerkin approximation with time-dependent basis functions. Typical numerical results are presented to illustrate the qualitative features of vibrations.

  12. A genetic scale of reading frame coding.

    Science.gov (United States)

    Michel, Christian J

    2014-08-21

    The reading frame coding (RFC) of codes (sets) of trinucleotides is a genetic concept which has been largely ignored during the last 50 years. A first objective is the definition of a new and simple statistical parameter PrRFC for analysing the probability (efficiency) of reading frame coding (RFC) of any trinucleotide code. A second objective is to reveal different classes and subclasses of trinucleotide codes involved in reading frame coding: the circular codes of 20 trinucleotides and the bijective genetic codes of 20 trinucleotides coding the 20 amino acids. This approach allows us to propose a genetic scale of reading frame coding which ranges from 1/3 with the random codes (RFC probability identical in the three frames) to 1 with the comma-free circular codes (RFC probability maximal in the reading frame and null in the two shifted frames). This genetic scale shows, in particular, the reading frame coding probabilities of the 12,964,440 circular codes (PrRFC=83.2% in average), the 216 C(3) self-complementary circular codes (PrRFC=84.1% in average) including the code X identified in eukaryotic and prokaryotic genes (PrRFC=81.3%) and the 339,738,624 bijective genetic codes (PrRFC=61.5% in average) including the 52 codes without permuted trinucleotides (PrRFC=66.0% in average). Otherwise, the reading frame coding probabilities of each trinucleotide code coding an amino acid with the universal genetic code are also determined. The four amino acids Gly, Lys, Phe and Pro are coded by codes (not circular) with RFC probabilities equal to 2/3, 1/2, 1/2 and 2/3, respectively. The amino acid Leu is coded by a circular code (not comma-free) with a RFC probability equal to 18/19. The 15 other amino acids are coded by comma-free circular codes, i.e. with RFC probabilities equal to 1. The identification of coding properties in some classes of trinucleotide codes studied here may bring new insights in the origin and evolution of the genetic code. Copyright © 2014 Elsevier

  13. Vibration Theory, Vol. 1A

    DEFF Research Database (Denmark)

    Nielsen, Søren R. K.

    The present collection of solved problems has been published as a supplement to the textbook Svingningsteori. Bind 1. Lineær svingningsteori,Aalborg tekniske Universitetsforlag, 1991, whicj is used in the introductory course on linear vibration theory that is being given on th e8th semester...

  14. Vibration Damping Circuit Card Assembly

    Science.gov (United States)

    Hunt, Ronald Allen (Inventor)

    2016-01-01

    A vibration damping circuit card assembly includes a populated circuit card having a mass M. A closed metal container is coupled to a surface of the populated circuit card at approximately a geometric center of the populated circuit card. Tungsten balls fill approximately 90% of the metal container with a collective mass of the tungsten balls being approximately (0.07) M.

  15. Wideband Piezomagnetoelastic Vibration Energy Harvesting

    DEFF Research Database (Denmark)

    Lei, Anders; Thomsen, Erik Vilain

    2014-01-01

    This work presents a small-scale wideband piezomagnetoelastic vibration energy harvester (VEH) aimed for operation at frequencies of a few hundred Hz. The VEH consists of a tape-casted PZT cantilever with thin sheets of iron foil attached on each side of the free tip. The wideband operation...

  16. Ultrafast vibrations of gold nanorings

    DEFF Research Database (Denmark)

    Kelf, T; Tanaka, Y; Matsuda, O

    2011-01-01

    We investigate the vibrational modes of gold nanorings on a silica substrate with an ultrafast optical technique. By comparison with numerical simulations, we identify several resonances in the gigahertz range associated with axially symmetric deformations of the nanoring and substrate. We...

  17. Effect of shelf aging on vibration transmissibility of anti-vibration gloves.

    Science.gov (United States)

    Shibata, Nobuyuki

    2017-10-05

    Anti-vibration gloves have been used in real workplaces to reduce vibration transmitted through hand-held power tools to the hand. Generally materials used for vibration attenuation in gloves are resilient materials composed of certain synthetic and/or composite polymers. The mechanical characteristics of the resilient materials used in anti-vibration gloves are prone to be influenced by environmental conditions such as temperature, humidity, and photo-irradiation, which cause material degradation and aging. This study focused on the influence of shelf aging on the vibration attenuation performance of air-packaged anti-vibration gloves following 2 years of shelf aging. Effects of shelf aging on the vibration attenuation performance of anti-vibration gloves were examined according to the Japan industrial standard JIS T8114 test protocol. The findings indicate that shelf aging induces the reduction of vibration attenuation performance in air-packaged anti-vibration gloves.

  18. Wood frame systems for wood homes

    Directory of Open Access Journals (Sweden)

    Julio Cesar Molina

    2010-12-01

    Full Text Available The use of constructive systems that combine strength, speed, with competitive differential techniques and mainly, compromising with the environment, is becoming more popular in Brazil. The constructive system in wood frame for houses of up to five stories is very interesting, because it is a light system, structured in reforested treated wood which allows the combination of several materials, besides allowing speed in the construction and total control of the expenses already in the project phase for being industrialized. The structural behavior of the wood frame is superior to the structural masonry in strength, thermal and acoustic comfort. However, in Brazil, the wood frame is still little known and used, due to lack of technical knowledge about the system, prejudice associated the bad use of the wood as construction material, or still, in some cases, lack of normalization. The aim of this manuscript consists of presenting the main technical characteristics and advantages of the constructive system in wood frame homes, approaching the main stages of the constructive process through examples, showing the materials used in the construction, in addition the main international normative recommendations of the project. Thus, this manuscript also hopes to contribute to the popularization of the wood frame system in Brazil, since it is a competitive, fast and ecologically correct system. Moreover, nowadays, an enormous effort of the technical, commercial and industrial section has been accomplished for the development of this system in the country.

  19. Femoral anatomical frame: assessment of various definitions.

    Science.gov (United States)

    Della Croce, U; Camomilla, V; Leardini, A; Cappozzo, A

    2003-06-01

    The reliability of the estimate of joint kinematic variables and the relevant functional interpretation are affected by the uncertainty with which bony anatomical landmarks and underlying bony segment anatomical frames are determined. When a stereo-photogrammetric system is used for in vivo studies, minimising and compensating for this uncertainty is crucial. This paper deals with the propagation of the errors associated with the location of both internal and palpable femoral anatomical landmarks to the estimation of the orientation of the femoral anatomical frame and to the knee joint angles during movement. Given eight anatomical landmarks, and the precision with which they can be identified experimentally, 12 different rules were defined for the construction of the anatomical frame and submitted to comparative assessment. Results showed that using more than three landmarks allows for more repeatable anatomical frame orientation and knee joint kinematics estimation. Novel rules are proposed that use optimization algorithms. On the average, the femoral frame orientation dispersion had a standard deviation of 2, 2.5 and 1.5 degrees for the frontal, transverse, and sagittal plane, respectively. However, a proper choice of the relevant construction rule allowed for a reduction of these inaccuracies in selected planes to 1 degrees rms. The dispersion of the knee adduction-abduction and internal-external rotation angles could also be limited to 1 degrees rms irrespective of the flexion angle value.

  20. Expanding Technological Frames Towards Mediated Collaboration

    DEFF Research Database (Denmark)

    Bjørn, Pernille; Scupola, Ada; Fitzgerald, Brian

    2006-01-01

    of their work practices and use of technology. Finally the third step includes participants' commitment and practical enactment of groupware. One of the key findings is that in groupware adoption the alignment of the individual technological frames requires articulation and re-evaluation of experienced......This paper provides an in-depth analysis of technological and social factors leading to the successful adoption of groupware in a virtual team in educational setting. Drawing on a theoretical framework based on the concept of technological frames, we conducted an action research study to analyze...... the chronological sequence of events leading to groupware adoption. We argue that groupware adoption can be conceptualized as a three-step process of expanding and aligning individual technological frames towards groupware: The first step comprises activities facilitating participants in articulation and evaluation...

  1. High Speed Frame Synchronization and Viterbi Decoding

    DEFF Research Database (Denmark)

    Paaske, Erik; Justesen, Jørn; Larsen, Knud J.

    1998-01-01

    The study has been divided into two phases. The purpose of Phase 1 of the study was to describe the system structure and algorithms in sufficient detail to allow drawing the high level architecture of units containing frame synchronization and Viterbi decoding. After selection of which specific...... potentially useful.Algorithms for frame synchronization are described and analyzed. Further, the high level architecture of units that contain frame synchronization and various other functions needed in a complete system is presented. Two such units are described, one for placement before the Viterbi decoder...... towards a realization in an FPGA.Node synchronization performed within a Viterbi decoder is discussed, and the high level architectures of three possible implementations of Viterbi decoders are described: The first implementation uses a number of commercially available decoders while the the two others...

  2. Scaffolding Advanced Writing through Writing Frames

    Directory of Open Access Journals (Sweden)

    Sara Salehpour

    2014-05-01

    Full Text Available Mastering writing has always proved an almost insurmountable barrier to EFL learners. In an attempt to alleviate problems advanced EFL learners have with writing, this study aimed at investigating the effect of scaffolded instruction through writing frames constructed from extended prefabricated lexical bundles. 40 female advanced English students, selected out of a population of 65, were randomly assigned into experimental and control groups. The participants of both groups were assigned a writing pre-test prior to any instruction, and a writing post-test following the twenty-session scaffolded instruction in both groups. The results revealed that the participants in the experimental group outperformed their counterparts in the control group as a result of the writing frames they were provided with. Overall, it is concluded that scaffolded instruction through writing frames can be a useful means of helping advanced students to improve their writing quality.

  3. Frame Complexity and the Financial Crisis

    DEFF Research Database (Denmark)

    Kleinnijenhuis, Jan; Schultz, Friederike; Oegema, Dirk

    2015-01-01

    Communicative complexity concerns the variety of issues and stakeholders (agenda complexity) and their associations (frame complexity) in the news. One issue may dominate news in crises (9/11, Katrina), but as soon as complexity recovers, uncertainty may decrease and the public mood may improve. ...... gradual recovery was only partly interrupted by the euro crisis. A Vector AutoRegression time series analysis shows that increasing frame complexity may indeed have fostered the recovery of financial markets and consumer confidence........ The financial crisis in the United States, the United Kingdom, and Germany (2007–2012) offers an example. An automated content analysis was applied to over 160,000 newspaper articles. Frame complexity decreased until the spotlight fell on the demise of Bear Stearns and Lehman Brothers (2008). The subsequent...

  4. Framing Trust at the Street-Level

    DEFF Research Database (Denmark)

    Perry, Kevin Anthony

    and artefacts such as media and local authority reports. In addition to the empirical material, the study explores a key governmental policy to investigate how the (previous) government names and frames people with minority ethnic backgrounds. Analysing this policy helps to locate the fieldwork and interactants...... in the community? 325 The thesis offers a discussion of the theoretical framework, methodological and ethical considerations along with issues pertaining to reliability and validity. Thereafter follow five analytical sections, the first of which offers a unique insight into the dynamics and mechanisms at play when...... and distrust as cultural frames or resources. The fieldwork data suggest that the young men with minority ethnic backgrounds use trust and distrust as cultural frames (resources) to organise their relationships with public sector employees. During this process, they rely upon a number of cultural tools...

  5. Frames and metaphors on social media

    DEFF Research Database (Denmark)

    Holmgreen, Lise-Lotte

    The role of social media in giving voice to public opinion is impossible to ignore. Increasingly, platforms such as Facebook and Twitter are used for the mobilisation of action against public figures, corporations and organisations which have attracted negative public attention. For the social...... spreading of coherent frames across diverse groups of publics, the underlying conceptual dimension of these frames has only been studied to a limited degree, and primarily within crisis communication research (Ngai et al. 2015; Van der Meer et al. 2014). However, studying the conceptual grounding may offer...... research (Liu 2010; Liu et al. 2011; Van der Meer & Verhoeven 2013), which provides the analyst with tools for investigating the conceptual and linguistic levels of communication on social media. Being concerned with the cognitive information processing of the receivers of text, framing can be instantiated...

  6. Supporting Product Line Evolution with Framed Aspects

    DEFF Research Database (Denmark)

    Loughran, Neil; Rashid, Awais; Zhang, Weishan

    2004-01-01

    user requirements, new technologies, business rules and features. However, the evolution process can be compromised by inadequate mechanisms for expressing the required changes. It maybe possible to anticipate future evolutions and, therefore, prepare and design the architecture to accommodate this......This paper discusses how evolution in software product lines can be supported using framed aspects: a combination of aspect-oriented programming and frame technology. Product line architectures and assets are subject to maintenance and evolution throughout their lifetime due to the emergence of new......, but there will eventually come a time when a certain feature or scenario appears which could not have been foreseen in the early stages of development. We argue that frames and aspects when used in isolation cannot overcome these weaknesses effectively. However, they can be addressed by using the respective strengths...

  7. Hamiltonian deformations of Gabor frames: First steps.

    Science.gov (United States)

    de Gosson, Maurice A

    2015-03-01

    Gabor frames can advantageously be redefined using the Heisenberg-Weyl operators familiar from harmonic analysis and quantum mechanics. Not only does this redefinition allow us to recover in a very simple way known results of symplectic covariance, but it immediately leads to the consideration of a general deformation scheme by Hamiltonian isotopies (i.e. arbitrary paths of non-linear symplectic mappings passing through the identity). We will study in some detail an associated weak notion of Hamiltonian deformation of Gabor frames, using ideas from semiclassical physics involving coherent states and Gaussian approximations. We will thereafter discuss possible applications and extensions of our method, which can be viewed - as the title suggests - as the very first steps towards a general deformation theory for Gabor frames.

  8. Microlens frames for laser diode arrays

    Science.gov (United States)

    Skidmore, J.A.; Freitas, B.L.

    1999-07-13

    Monolithic microlens frames enable the fabrication of monolithic laser diode arrays and are manufactured inexpensively with high registration, and with inherent focal length compensation for any lens diameter variation. A monolithic substrate is used to fabricate a low-cost microlens array. The substrate is wet-etched or sawed with a series of v-grooves. The v-grooves can be created by wet-etching, by exploiting the large etch-rate selectivity of different crystal planes. The v-grooves provide a support frame for either cylindrical or custom-shaped microlenses. Because the microlens frames are formed by photolithographic semiconductor batch-processing techniques, they can be formed inexpensively over large areas with precise lateral and vertical registration. The v-groove has an important advantage for preserving the correct focus for lenses of varying diameter. 12 figs.

  9. News framing and public opinion: A mediation analysis of framing effects on political attitudes

    NARCIS (Netherlands)

    Lecheler, S.K.; de Vreese, C.H.

    2012-01-01

    There is no satisfactory account of the psychological processes that mediate a news framing effect. Based on an experimental study (N = 1,537), this article presents a mediation analysis of a news framing effect on opinion, testing for two important mediation processes: belief importance and belief

  10. Episode Type, Attachment Orientation, and Frame Salience: Evidence for a Theory of Relational Framing.

    Science.gov (United States)

    Solomon, Denise Haunani; Dillard, James Price; Anderson, Jason W.

    2002-01-01

    Notes that relational framing theory asserts that dominance-submission and affiliation-disaffiliation tend to displace each other as frames for processing social interaction. Replicates and extends previous tests of these claims by evaluating three hypotheses. Finds that results are consistent with all three of the hypotheses, but relational…

  11. Authentication of Surveillance Videos: Detecting Frame Duplication Based on Residual Frame.

    Science.gov (United States)

    Fadl, Sondos M; Han, Qi; Li, Qiong

    2017-10-16

    Nowadays, surveillance systems are used to control crimes. Therefore, the authenticity of digital video increases the accuracy of deciding to admit the digital video as legal evidence or not. Inter-frame duplication forgery is the most common type of video forgery methods. However, many existing methods have been proposed for detecting this type of forgery and these methods require high computational time and impractical. In this study, we propose an efficient inter-frame duplication detection algorithm based on standard deviation of residual frames. Standard deviation of residual frame is applied to select some frames and ignore others, which represent a static scene. Then, the entropy of discrete cosine transform coefficients is calculated for each selected residual frame to represent its discriminating feature. Duplicated frames are then detected exactly using subsequence feature analysis. The experimental results demonstrated that the proposed method is effective to identify inter-frame duplication forgery with localization and acceptable running time. © 2017 American Academy of Forensic Sciences.

  12. The effects of sound level and vibration magnitude on the relative discomfort of noise and vibration.

    Science.gov (United States)

    Huang, Yu; Griffin, Michael J

    2012-06-01

    The relative discomfort caused by noise and vibration, how this depends on the level of noise and the magnitude of vibration, and whether the noise and vibration are presented simultaneously or sequentially has been investigated in a laboratory study with 20 subjects. Noise and vertical vibration were reproduced with all 49 combinations of 7 levels of noise and 7 magnitudes of vibration to allow the discomfort caused by one of the stimuli to be judged relative to the other stimulus using magnitude estimation. In four sessions, subjects judged noise relative to vibration and vibration relative to noise, with both simultaneous and sequential presentations of the stimuli. The equivalence of noise and vibration was not greatly dependent on whether the stimuli were simultaneous or sequential, but highly dependent on whether noise was judged relative to vibration or vibration was judged relative to noise. When judging noise, higher magnitude vibrations appeared to mask the discomfort caused by low levels of noise. When judging vibration, higher level noises appeared to mask the discomfort caused by low magnitudes of vibration. The judgment of vibration discomfort was more influenced by noise than the judgment of noise discomfort was influenced by vibration.

  13. Transient vibration of wind turbine blades

    Science.gov (United States)

    Li, Yuanzhe; Li, Minghai; Jiang, Feng

    2017-09-01

    This article aims to the transient vibration of wind turbine blades. We firstly introduce transient vibration and previous studies in this area. The report then shows the fundamental equations and derivation of Euler Equation. A 3-D beam are created to compare the analytical and numerical result. In addition we operate the existing result and Patran result of a truncation wedge beam, especially the frequencies of free vibration and transient vibration. Transient vibration cannot be vanished but in some case it can be reduced.

  14. The Game Frame and Political Efficacy

    DEFF Research Database (Denmark)

    Pedersen, Rasmus Tue

    2012-01-01

    Several observational and experimental studies have confirmed the ‘spiral of cynicism’ hypothesis: the tendency of the news media to cover politics through a game frame, which focuses on political strategy instead of political issues, leads to cynicism about election campaigns and politicians amo...... on a survey among the electorate and a content analysis of political coverage in newspapers. The study shows that exposure to the game frame is indeed associated with lower levels of internal efficacy, even when controlling for potentially confounding variables....

  15. A protoscientific master metaphor for framing violence.

    Science.gov (United States)

    Krauss, Herbert H

    2006-11-01

    Every new field of investigation requires a guiding scheme or frame. Its purpose is to provide a heuristic for discovery and a structure for organizing information. Neither the World Health Organization's public health nor a biosocial model of violence are adequate for providing a protoscientific frame for conceptualizing violent acts. This essay suggests a master metaphor--Burke's Dramatism--through which to deepen and expand our knowledge of violence and what must be done to reduce its toll. An illustrative example is presented.

  16. Riemannian geometry in an orthogonal frame

    CERN Document Server

    Cartan, Elie Joseph

    2001-01-01

    Foreword by S S Chern. In 1926-27, Cartan gave a series of lectures in which he introduced exterior forms at the very beginning and used extensively orthogonal frames throughout to investigate the geometry of Riemannian manifolds. In this course he solved a series of problems in Euclidean and non-Euclidean spaces, as well as a series of variational problems on geodesics. In 1960, Sergei P Finikov translated from French into Russian his notes of these Cartan's lectures and published them as a book entitled Riemannian Geometry in an Orthogonal Frame. This book has many innovations, such as the n

  17. Time delay control of power converters: Mixed frame and stationary-frame variants

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Loh, P.C.; Tang, Y.

    2008-01-01

    In this paper, a mixed-frame and a stationary-frame time delay current controller are proposed for high precision reference tracking and disturbance rejection of power converters. In particular, the controllers use a proportional-resonant regulator in the stationary frame for regulating...... the positive and negative-sequence fundamental currents, which are known to directly influence the flow of active and reactive power in most energy conversion systems. Moreover, for the tracking or compensation of harmonics, the controllers include a time delay control path in either the synchronous...... or stationary frame, whose inherent feedback and feedforward structure can be proven to resemble a bank of resonant filters in either reference frames. Unlike other existing controllers, the proposed time delay controllers function by introducing multiple resonant peaks at only those harmonic frequencies...

  18. On the interaction between media frames and individual frames of the Israeli-Palestinian conflict

    Directory of Open Access Journals (Sweden)

    Wilhelm Kempf

    2012-10-01

    Full Text Available The present paper reports on a media effects research experiment in which six groups of participants were asked to read and evaluate differently framed news articles about two scenarios: a Palestinian attack on Israel and an Israeli military operation against Palestinians. The experimental results show that media peace frames of violent events in the Israeli-Palestinian conflict are generally regarded by the German public as more comprehensible, less biased, more balanced and less partisan than media war frames of the same events. The specific ways in which recipients respond to the frames, however, depend on their prior knowledge of the conflict, on their positioning to the conflict and on their sensitivity to the ambivalence of war and peace for both Israel and the Palestinians. This supports the hypothesis that neither news selection nor framing have uniform effects on public opinion.

  19. Multiple Rabi Splittings under Ultrastrong Vibrational Coupling.

    Science.gov (United States)

    George, Jino; Chervy, Thibault; Shalabney, Atef; Devaux, Eloïse; Hiura, Hidefumi; Genet, Cyriaque; Ebbesen, Thomas W

    2016-10-07

    From the high vibrational dipolar strength offered by molecular liquids, we demonstrate that a molecular vibration can be ultrastrongly coupled to multiple IR cavity modes, with Rabi splittings reaching 24% of the vibration frequencies. As a proof of the ultrastrong coupling regime, our experimental data unambiguously reveal the contributions to the polaritonic dynamics coming from the antiresonant terms in the interaction energy and from the dipolar self-energy of the molecular vibrations themselves. In particular, we measure the opening of a genuine vibrational polaritonic band gap of ca. 60 meV. We also demonstrate that the multimode splitting effect defines a whole vibrational ladder of heavy polaritonic states perfectly resolved. These findings reveal the broad possibilities in the vibrational ultrastrong coupling regime which impact both the optical and the molecular properties of such coupled systems, in particular, in the context of mode-selective chemistry.

  20. Vibrations on board and health effects

    DEFF Research Database (Denmark)

    Jensen, Anker; Jepsen, Jørgen Riis

    2014-01-01

    for such relation among seafarers except for fishermen, who, however, are also exposed to additional recognised physical risk factors at work. The assessment and reduction of vibrations by naval architects relates to technical implications of this impact for the ships’ construction, but has limited value......There is only limited knowledge of the exposure to vibrations of ships’ crews and their risk of vibration-induced health effects. Exposure to hand-arm vibrations from the use of vibrating tools at sea does not differ from that in the land-based trades. However, in contrast to most other work places...... of the health consequences of whole body vibrations in land-transportation, such exposure at sea may affect ships’ passengers and crews. While the relation of back disorders to high levels of whole body vibration has been demonstrated among e.g. tractor drivers, there are no reported epidemiological evidence...

  1. Probe Oscillation Shear Elastography (PROSE): A High Frame-Rate Method for Two-Dimensional Ultrasound Shear Wave Elastography.

    Science.gov (United States)

    Mellema, Daniel C; Song, Pengfei; Kinnick, Randall R; Urban, Matthew W; Greenleaf, James F; Manduca, Armando; Chen, Shigao

    2016-09-01

    Ultrasound shear wave elastography (SWE) utilizes the propagation of induced shear waves to characterize the shear modulus of soft tissue. Many methods rely on an acoustic radiation force (ARF) "push beam" to generate shear waves. However, specialized hardware is required to generate the push beams, and the thermal stress that is placed upon the ultrasound system, transducer, and tissue by the push beams currently limits the frame-rate to about 1 Hz. These constraints have limited the implementation of ARF to high-end clinical systems. This paper presents Probe Oscillation Shear Elastography (PROSE) as an alternative method to measure tissue elasticity. PROSE generates shear waves using a harmonic mechanical vibration of an ultrasound transducer, while simultaneously detecting motion with the same transducer under pulse-echo mode. Motion of the transducer during detection produces a "strain-like" compression artifact that is coupled with the observed shear waves. A novel symmetric sampling scheme is proposed such that pulse-echo detection events are acquired when the ultrasound transducer returns to the same physical position, allowing the shear waves to be decoupled from the compression artifact. Full field-of-view (FOV) two-dimensional (2D) shear wave speed images were obtained by applying a local frequency estimation (LFE) technique, capable of generating a 2D map from a single frame of shear wave motion. The shear wave imaging frame rate of PROSE is comparable to the vibration frequency, which can be an order of magnitude higher than ARF based techniques. PROSE was able to produce smooth and accurate shear wave images from three homogeneous phantoms with different moduli, with an effective frame rate of 300 Hz. An inclusion phantom study showed that increased vibration frequencies improved the accuracy of inclusion imaging, and allowed targets as small as 6.5 mm to be resolved with good contrast (contrast-to-noise ratio ≥ 19 dB) between the target and

  2. Toward black-box-type full- and reduced-dimensional variational (ro)vibrational computations

    Science.gov (United States)

    Mátyus, Edit; Czakó, Gábor; Császár, Attila G.

    2009-04-01

    A black-box-type algorithm is presented for the variational computation of energy levels and wave functions using a (ro)vibrational Hamiltonian expressed in an arbitrarily chosen body-fixed frame and in any set of internal coordinates of full or reduced vibrational dimensionality. To make the required numerical work feasible, matrix representation of the operators is constructed using a discrete variable representation (DVR). The favorable properties of DVR are exploited in the straightforward and numerically exact inclusion of any representation of the potential and the kinetic energy including the G matrix and the extrapotential term. In this algorithm there is no need for an a priori analytic derivation of the kinetic energy operator, as all of its matrix elements at each grid point are computed numerically either in a full- or a reduced-dimensional model. Due to the simple and straightforward definition of reduced-dimensional models within this approach, a fully anharmonic variational treatment of large, otherwise intractable molecular systems becomes available. In the computer code based on the above algorithm, there is no inherent limitation for the maximally coupled number of vibrational degrees of freedom. However, in practice current personal computers allow the treatment of about nine fully coupled vibrational dimensions. Computation of vibrational band origins of full and reduced dimensions showing the advantages and limitations of the algorithm and the related computer code are presented for the water, ammonia, and methane molecules.

  3. Design and experimental study of a velocity amplified electromagnetic vibration energy harvester

    Science.gov (United States)

    Klein, Jackson A.; Zuo, Lei

    2017-04-01

    Dedicated sensors are widely used throughout many industries to monitor everyday operations, maintain safety and report performance characteristics. In order to adopt a more sustainable solution, intensive research is being conducted for self-powered sensing. To enable sensors to power themselves, harvesting energy from environmental vibration has been widely studied, however, its overall effectiveness remains questionable due to small vibration amplitudes and thus limited harvestable energy density. This paper addresses the issue by proposing a novel vibration energy harvester in which a metal compliant mechanism frame is used to house both a linear electromagnetic generator and proof mass. Due to the compliant mechanism, the proposed energy harvester is capable of amplifying machine vibration velocity for a dedicated electromagnetic generator, largely increasing the energy density. The harvester prototype is also fabricated and experimentally characterized to verify its effectiveness. When operating at its natural frequency in a low base amplitude, 0.001 in (25.4μm) at 19.4 Hz, during lab tests, the harvester has been shown to produce up to 0.91 V AC open voltage, and a maximum power of 2 mW, amplifying the relative proof mass velocity by approximately 5.4 times. In addition, a mathematical model is created based on the pseudo-rigid-body dynamics and the analysis matches closely with experiments. The proposed harvester was designed using vibration data from nuclear power plants. Further steps for improving such a design are given for broader applications.

  4. Health risks of vibration exposure to wheelchair users in the community

    Science.gov (United States)

    Garcia-Mendez, Yasmin; Pearlman, Jonathan L.; Boninger, Michael L.; Cooper, Rory A.

    2013-01-01

    Objective The purpose of this study was to evaluate whole-body vibration (WBV) exposure to wheelchair (WC) users in their communities and to determine the effect of WC frame type (folding, rigid, and suspension) in reducing WBV transmitted to the person. Design An observational case-control study of the WBV exposure levels among WC users. Participants Thirty-seven WC users, with no pressure sores, 18 years old or older and able to perform independent transfers. Main outcome measures WC users were monitored for 2 weeks to collect WBV exposure, as well as activity levels, by using custom vibration and activity data-loggers. Vibration levels were evaluated using ISO 2631-1 methods. Results All WC users who participated in this study were continuously exposed to WBV levels at the seat that were within and above the health caution zone specified by ISO 2631-1 during their day-to-day activities (0.83 ± 0.17 m/second2, weighted root-mean-squared acceleration, for 13.07 ± 3.85 hours duration of exposure). WCs with suspension did not attenuate vibration transmitted to WC users (V = 0.180, F(8, 56) = 0.692, P = 0.697). Conclusions WBV exposure to WC users exceeds international standards. Suspension systems need to be improved to reduce vibrations transmitted to the users. PMID:23820152

  5. 49 CFR 230.107 - Tender frame and body.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Tender frame and body. 230.107 Section 230.107... Tenders Trucks, Frames and Equalizing System § 230.107 Tender frame and body. (a) Maintenance. Tender... repaired: (1) Portions of the tender frame or body (except wheels) that have less than a 21/2 inches...

  6. What Makes a Frame Persuasive? Lessons from Social Identity Theory

    Science.gov (United States)

    Mols, Frank

    2012-01-01

    We know from the issue-framing literature that politicians "frame" issues strategically to influence public perceptions and preferences. We also know that there are different framing techniques. What remains poorly understood, though, is what makes a frame persuasive. The proposition put forward in this debate paper is that social…

  7. Normative, gain and hedonic goal frames guiding environmental behavior

    NARCIS (Netherlands)

    Lindenberg, Siegwart; Steg, Linda

    2007-01-01

    This article discusses new developments about goal-dependent framing and multiple goal frames (sometimes also called "multiple motives"), which are highly relevant for understanding environmental behavior. We introduce goal-framing theory, which postulates that goals "frame" the way people process

  8. Framing in mass communication research: an overview and assessment

    NARCIS (Netherlands)

    Vliegenthart, R.

    2012-01-01

    This article provides an overview of the use of the framing concept in mass communication research. It focuses on the questions what a frame is and how it is measured, how variation in framing can be explained and what the effects of media framing are. Specific attention will be paid to the

  9. Downlink Transmission of Short Packets: Framing and Control Information Revisited

    DEFF Research Database (Denmark)

    Trillingsgaard, Kasper Fløe; Popovski, Petar

    2017-01-01

    Cellular wireless systems rely on frame-based transmissions. The frame design is conventionally based on heuristics, consisting of a frame header and a data part. The frame header contains control information that provides pointers to the messages within the data part. In this paper, we revisit t...

  10. Frame approximation of pseudo-inverse operators

    DEFF Research Database (Denmark)

    Christensen, Ole

    2001-01-01

    Let T denote an operator on a Hilbert space (H, [.,.]), and let {f(i)}(i=1)(infinity) be a frame for the orthogonal complement of the kernel NT. We construct a sequence of operators {Phi (n)} of the form Phi (n) (.) = Sigma (n)(i=1) [., g(t)(n)]f(i) which converges to the psuedo-inverse T+ of T...

  11. Schuman's Europe : his frame of reference

    NARCIS (Netherlands)

    Krijtenburg, Margriet

    2012-01-01

    Schuman’s Europe: His frame of reference provides an insight into the way European unification was envisioned by its founding father Robert Schuman. The thesis makes clear why Schuman can be considered the main architect of European unification because of his thoughts, his personality, his religious

  12. Frame independent nonlocality for three qubit state

    OpenAIRE

    Moradi, Shahpoor; Aghaee, Mohsen

    2012-01-01

    Bell's inequality is investigated for the three qubit GHZ state in relativistic regime. Two different relativistic spin operator are considered. One of them is defined by Lee, and the other is the Pauli-Lubanski pseudovector used by Kim \\textit{et al}. It is shown that for both spin operator Bell's inequality is still maximally violated in a Lorentz-boosted frame.

  13. Densification of FL Chains via Residuated Frames

    Czech Academy of Sciences Publication Activity Database

    Baldi, Paolo; Terui, K.

    2016-01-01

    Roč. 75, č. 2 (2016), s. 169-195 ISSN 0002-5240 R&D Projects: GA ČR GAP202/10/1826 Keywords : densifiability * standard completeness * residuated lattices * residuated frames * fuzzy logic Subject RIV: BA - General Mathematics Impact factor: 0.625, year: 2016

  14. The Definition of Open Reading Frame Revisited.

    Science.gov (United States)

    Sieber, Patricia; Platzer, Matthias; Schuster, Stefan

    2018-01-20

    The term open reading frame (ORF) is of central importance to gene finding. Surprisingly, at least three definitions are in use. We discuss several molecular biological and bioinformatics aspects, and we recommend using the definition in which an ORF is bounded by stop codons. Copyright © 2018 Elsevier Ltd. All rights reserved.

  15. Supervisors' Leadership Frames: Implications for Implementation of ...

    African Journals Online (AJOL)

    Supervisors' Leadership Frames: Implications for Implementation of Universal Basic Education (UBE) In Nigeria. ... in foreign bank account to the detriment of welfare of their people. That it should be an engagement of many people in leadership activity of directing and following the contour of expertise in an organization.

  16. Framing China: Transformation and Institutional Change

    NARCIS (Netherlands)

    B. Krug (Barbara); H. Hendrischke (Hans)

    2006-01-01

    textabstractThe paper offers a frame for investigating the extent to which decentralisation, and subsequent locally chosen institutions shape private organisational and institutional innovation. To include the numerous locally based “economic regimes” matters as the resulting business system

  17. Probabilistic modeling durability of wooden window frames

    NARCIS (Netherlands)

    Straalen, IJ.J. van; Abspoel-Bukman, L.M.; Courage, W.M.G.; Mennink, J.

    2014-01-01

    Nowadays, maintenance of wooden window frames strongly depends on the practical experience of the parties involved. To get a better understanding of the required maintenance period and maintenance actions, a model has been developed to predict durability. This model makes it possible to optimize

  18. Inertial frames and breakthrough propulsion physics

    Science.gov (United States)

    Millis, Marc G.

    2017-09-01

    The term ;Breakthrough Propulsion Physics; comes from the NASA project by that name which examined non-rocket space drives, gravity control, and faster-than-light travel. The focus here is on space drives and the related unsolved physics of inertial frames. A ;space drive; is a generic term encompassing any concept for using as-yet undiscovered physics to move a spacecraft instead of existing rockets, sails, or tethers. The collective state of the art spans mostly steps 1-3 of the scientific method: defining the problem, collecting data, and forming hypotheses. The key issues include (1) conservation of momentum, (2) absence of obvious reaction mass, and (3) the net-external thrusting requirement. Relevant open problems in physics include: (1) the sources and mechanisms of inertial frames, (2) coupling of gravitation to the other fundamental forces, and (3) the nature of the quantum vacuum. Rather than following the assumption that inertial frames are an immutable, intrinsic property of space, this paper revisits Mach's Principle, where it is posited that inertia is relative to the distant surrounding matter. This perspective allows conjectures that a space drive could impart reaction forces to that matter, via some as-yet undiscovered interaction with the inertial frame properties of space. Thought experiments are offered to begin a process to derive new hypotheses. It is unknown if this line of inquiry will be fruitful, but it is hoped that, by revisiting unsolved physics from a propulsion point of view, new insights will be gained.

  19. Classification of framed links in 3-manifolds

    Indian Academy of Sciences (India)

    manifolds, Preprint Series Univ. of Ljubljana 41 (2003) 906. [CRS2] Cencelj M, Repovš D and Skopenkov M, Classification of framed links in 3- manifolds, preprint, arXiv:math-gt/0705.4166v1. [Du] Dufraine E, Classes d'homotopie de champs de vecteurs Morse-Smale sans singular- ite sur les fibres de Seifert, Enseign.

  20. [Designing metal frame removable partial dentures

    NARCIS (Netherlands)

    Witter, D.J.; Barel, J.C.; Keltjens, H.M.A.M.; Creugers, N.H.J.

    2011-01-01

    Oral health care providers have the full responsibility for designing metal frame removable partial dentures and making all of the necessary preparations. Important principles of design are that the denture should hamper natural cleaning and daily oral hygiene as little as possible and that it

  1. Connecting VLBI and Gaia celestial reference frames

    Directory of Open Access Journals (Sweden)

    Zinovy Malkin

    2016-09-01

    Full Text Available The current state of the link problem between radio and optical celestial reference frames is considered.The main objectives of the investigations in this direction during the next few years are the preparation of a comparisonand the mutual orientation and rotation between the optical it Gaia Celestial Reference Frame (GCRFand the 3rd generation radio International Celestial Reference Frame (ICRF3, obtained from VLBI observations.Both systems, ideally, should be a realization of the ICRS (International Celestial Reference System at micro-arcsecond level accuracy.Therefore, the link accuracy between the ICRF and GCRF should be obtained with similar error level, which is not a trivial taskdue to relatively large systematic and random errors in source positions at different frequency bands.In this paper, a brief overview of recent work on the GCRF--ICRF link is presented.Additional possibilities to improve the GCRF--ICRF link accuracy are discussed.The suggestion is made to use astrometric radio sources with optical magnitude to 20$^m$ rather than to 18$^m$ as currently plannedfor the GCRF--ICRF link.In addition, the use of radio stars is also a prospective method to obtain independent and accurate orientation between the Gaia frame and the ICRF.

  2. A Model of Framing in Design Teams

    Science.gov (United States)

    Zahedi, Mithra; Heaton, Lorna

    2017-01-01

    How do ideas evolve in the context of collaborative design? This research explores the framing strategies and tools involved in the co-construction of a shared understanding in the early stages of a design project. We observed a team of four industrial design students working to design a pop-up shop. We found that, while the key design elements of…

  3. Foldable Frame Supporting Electromagnetic Radiation Collectors

    DEFF Research Database (Denmark)

    2011-01-01

    The present invention relates to flexible frames supporting electromagnetic radiation collectors, such as antennas, antenna reflectors, deflectors or solar collectors, for celestial or terrestrial applications, which can be folded to be stored and/or transported. The method for stowing deforms...

  4. Framing Gender Intersections in the European Union

    DEFF Research Database (Denmark)

    Lombardo, Emanuela; Agustin, Lise Rolandsen

    2012-01-01

    This article explores the extent to which the emergence of an antidiscrimination policy in the European Union (EU) implies a shift in EU gender equality policies towards an intersectional approach. The frame analysis of EU gender equality policy documents shows that intersectional dimensions...

  5. An Affect-Responsive Interactive Photo Frame

    NARCIS (Netherlands)

    Dibeklioğlu, H.; Kosunen, I.; Ortega Hortas, M.; Salah, A.A.; Zuzánek, P.; Salah, A.A.; Gevers, T.

    2010-01-01

    We develop an interactive photo-frame system in which a series of videos of a single person are automatically segmented and a response logic is derived to interact with the user in real-time. The system is composed of five modules. The first module analyzes the uploaded videos and prepares segments

  6. The framing effect and skin conductance responses

    Directory of Open Access Journals (Sweden)

    Patrick eRing

    2015-08-01

    Full Text Available Individuals often rely on simple heuristics when they face complex choice situations under uncertainty. Traditionally, it has been proposed that cognitive processes are the main driver to evaluate different choice options and finally to reach a decision. Growing evidence, however, highlights a strong interrelation between judgment and decision-making (JDM on the one hand, and emotional processes on the other hand. This also seems to apply to judgmental heuristics, i.e. decision-processes that are typically considered to be fast and intuitive. In this study, participants are exposed to different probabilities of receiving an unpleasant electric shock. Information about electric shock probabilities is either positively or negatively framed. Integrated skin conductance responses (ISCRs while waiting for electric shock realization are used as an indicator for participants' emotional arousal. This measure is compared to objective probabilities. I find evidence for a relation between emotional body reactions measured by ISCRs and the framing effect. Under negative frames, participants show significantly higher ISCRs while waiting for an electric shock to be delivered than under positive frames. This result might contribute to a better understanding of the psychological processes underlying JDM. Further studies are necessary to reveal the causality underlying this finding, i.e. whether emotional processes influence JDM or vice versa.

  7. District Leaders' Framing of Educator Evaluation Policy

    Science.gov (United States)

    Woulfin, Sarah L.; Donaldson, Morgaen L.; Gonzales, Richard

    2016-01-01

    Purpose: Educator evaluation systems have recently undergone scrutiny and reform, and district and school leaders play a key role in interpreting and enacting these systems. This article uses framing theory to understand district leaders' interpretation and advancement of a state's new educator evaluation policy. Research Methods: The article…

  8. Triphenyl phosphate allergy from spectacle frames

    DEFF Research Database (Denmark)

    Carlsen, L; Andersen, K E; Egsgaard, Helge

    1986-01-01

    A case of triphenyl phosphate allergy from spectacle frames is reported. Patch tests with analytical grade triphenyl phosphate, tri-m-cresyl phosphate, and tri-p-cresyl phosphate in the concentrations 5%, 0.5% and 0.05% pet. showed positive reactions to 0.05% triphenyl phosphate and 0.5% tri...... triphenyl phosphate allergy in our patient....

  9. Equiangular tight frames and unistochastic matrices

    Czech Academy of Sciences Publication Activity Database

    Goyeneche, D.; Turek, Ondřej

    2017-01-01

    Roč. 50, č. 24 (2017), č. článku 245304. ISSN 1751-8113 R&D Projects: GA ČR GA17-01706S Institutional support: RVO:61389005 Keywords : equiangular tight frames * unistochastic matrices * SIC POVM Subject RIV: BE - Theoretical Physics Impact factor: 1.857, year: 2016

  10. Framing Learning Conditions in Geography Excursions

    Science.gov (United States)

    Jonasson, Mikael

    2011-01-01

    The aim of this paper is to investigate and frame some learning conditions involved in the practice of geographical excursions. The empirical material from this study comes from several excursions made by students in human geography and an ethnomethodological approach through participant observation is used. The study is informed by theories from…

  11. Compactly supported frames for decomposition spaces

    DEFF Research Database (Denmark)

    Nielsen, Morten; Rasmussen, Kenneth Niemann

    2012-01-01

    In this article we study a construction of compactly supported frame expansions for decomposition spaces of Triebel-Lizorkin type and for the associated modulation spaces. This is done by showing that finite linear combinations of shifts and dilates of a single function with sufficient decay in b...

  12. Reference frames and rigid motions in relativity

    Science.gov (United States)

    Llosa, J.; Soler, D.

    2004-07-01

    A reference frame consists of a reference space, a time scale and a spatial metric. The geometric structure induced by these objects in spacetime is developed. The existence of a class of spatial metrics which are rigid, have free mobility and can be derived as a slight deformation of the radar metric, is demonstrated.

  13. The Institutional Framing of the Market Economy

    DEFF Research Database (Denmark)

    Howells, John

    2003-01-01

    A review of the significance of the intellectual tool of the technology complex for an understanding of the role of innovation in the market economy. The framing of the market economy is understood as the way that institutions of finance, education and intellectual property are reformed to aid th...

  14. Leaders as Linchpins for Framing Meaning

    Science.gov (United States)

    Eddy, Pamela L.

    2010-01-01

    Community college leaders serve as linchpins for framing meaning on campus. The current pressures on institutions (given declining financial resources, demands for accountability, changing faculty ranks, and societal need for new knowledge) require presidents to juggle multiple priorities while presenting a cohesive message to campus constituents.…

  15. The Hot Hand Belief and Framing Effects

    Science.gov (United States)

    MacMahon, Clare; Köppen, Jörn; Raab, Markus

    2014-01-01

    Purpose: Recent evidence of the hot hand in sport--where success breeds success in a positive recency of successful shots, for instance--indicates that this pattern does not actually exist. Yet the belief persists. We used 2 studies to explore the effects of framing on the hot hand belief in sport. We looked at the effect of sport experience and…

  16. Infinite matrices, wavelet coefficients and frames

    Directory of Open Access Journals (Sweden)

    N. A. Sheikh

    2004-01-01

    Full Text Available We study the action of A on f∈L2(ℝ and on its wavelet coefficients, where A=(almjklmjk is a double infinite matrix. We find the frame condition for A-transform of f∈L2(ℝ whose wavelet series expansion is known.

  17. Wood-framed houses for earthquake zones

    DEFF Research Database (Denmark)

    Hansen, Klavs Feilberg

    Wood-framed houses with a sheathing are suitable for use in earthquake zones. The Direction describes a method of determining the earthquake forces in a house and shows how these forces can be resisted by diaphragm action in the walls, floors, and roof, of the house. An appendix explains how...

  18. Vibration characteristics of casing string under the exciting force of an electric vibrator

    Directory of Open Access Journals (Sweden)

    Yiyong Yin

    2017-11-01

    Full Text Available Vibration cementing is a new technique that can significantly improve the bond strength of cementing interface. To popularize this technique, it is necessary to solve the key problem of how to make cementing string generate downhole radial vibration in the WOC stage. For this purpose, an electric vibrator was developed. With this vibrator, electric energy is converted into mechanical energy by means of a high-temperature motor vibration unit. The motor vibration unit rotates the eccentric block through an output shaft to generate an exciting source, which produces an axial-rotating exciting force at the bottom of the casing string. Then, the vibration characteristics of vertical well casing string under the exciting force were analyzed by using the principal coordinate analysis method, and the response model of casing string to an electric vibrator was developed. Finally, the effects of casing string length, exciting force and vibration frequency on the vibration amplitude at the lowermost of the casing string were analyzed based on a certain casing program. It is indicated that the casing string length and the square of vibration frequency are inversely proportional to the vibration amplitude at the lowermost of the casing string, and the exciting force is proportional to the vibration amplitude at the lowermost of the casing string. These research results provide a theoretical support for the application of vibration cementing technology to the cementing sites with different requirements on well depth and amplitude.

  19. Coding B-Frames of Color Videos with Fuzzy Transforms

    Directory of Open Access Journals (Sweden)

    Ferdinando Di Martino

    2013-01-01

    Full Text Available We use a new method based on discrete fuzzy transforms for coding/decoding frames of color videos in which we determine dynamically the GOP sequences. Frames can be differentiated into intraframes, predictive frames, and bidirectional frames, and we consider particular frames, called Δ-frames (resp., R-frames, for coding P-frames (resp., B-frames by using two similarity measures based on Lukasiewicz -norm; moreover, a preprocessing phase is proposed to determine similarity thresholds for classifying the above types of frame. The proposed method provides acceptable results in terms of quality of the reconstructed videos to a certain extent if compared with classical-based F-transforms method and the standard MPEG-4.

  20. An Algorithm of Extracting I-Frame in Compressed Video

    Directory of Open Access Journals (Sweden)

    Zhu Yaling

    2015-01-01

    Full Text Available The MPEG video data includes three types of frames, that is: I-frame, P-frame and B-frame. However, the I-frame records the main information of video data, the P-frame and the B-frame are just regarded as motion compensations of the I-frame. This paper presents the approach which analyzes the MPEG video stream in the compressed domain, and find out the key frame of MPEG video stream by extracting the I-frame. Experiments indicated that this method can be automatically realized in the compressed MPEG video and it will lay the foundation for the video processing in the future.

  1. Vibrational damping of composite materials

    Science.gov (United States)

    Biggerstaff, Janet M.

    The purpose of this research was to develop new methods of vibrational damping in polymeric composite materials along with expanding the knowledge of currently used vibrational damping methods. A new barrier layer technique that dramatically increased damping in viscoelastic damping materials that interacted with the composite resin was created. A method for testing the shear strength of damping materials cocured in composites was developed. Directional damping materials, where the loss factor and modulus could be tailored by changing the angle, were produced and investigated. The addition of particles between composite prepreg layers to increase damping was studied. Electroviscoelastic materials that drastically changed properties such as loss factor and modulus with an applied voltage were manufactured and tested.

  2. Vibration of imperfect rotating disk

    Directory of Open Access Journals (Sweden)

    Půst L.

    2011-12-01

    Full Text Available This study is concerned with the theoretical and numerical calculations of the flexural vibrations of a bladed disk. The main focus of this study is to elaborate the basic background for diagnostic and identification methods for ascertaining the main properties of the real structure or an experimental model of turbine disks. The reduction of undesirable vibrations of blades is proposed by using damping heads, which on the experimental model of turbine disk are applied only on a limited number of blades. This partial setting of damping heads introduces imperfection in mass, stiffness and damping distribution on the periphery and leads to more complicated dynamic properties than those of a perfect disk. Calculation of FEM model and analytic—numerical solution of disk behaviour in the limited (two modes frequency range shows the splitting of resonance with an increasing speed of disk rotation. The spectrum of resonance is twice denser than that of a perfect disk.

  3. Dynamical response of vibrating ferromagnets

    CERN Document Server

    Gaganidze, E; Ziese, M

    2000-01-01

    The resonance frequency of vibrating ferromagnetic reeds in a homogeneous magnetic field can be substantially modified by intrinsic and extrinsic field-related contributions. Searching for the physical reasons of the field-induced resonance frequency change and to study the influence of the spin glass state on it, we have measured the low-temperature magnetoelastic behavior and the dynamical response of vibrating amorphous and polycrystalline ferromagnetic ribbons. We show that the magnetoelastic properties depend strongly on the direction of the applied magnetic field. The influence of the re-entrant spin glass transition on these properties is discussed. We present clear experimental evidence that for applied fields perpendicular to the main area of the samples the behavior of ferromagnetic reeds is rather independent of the material composition and magnetic state, exhibiting a large decrease of the resonance frequency. This effect can be very well explained with a model based on the dynamical response of t...

  4. Vibrational coupling in plasmonic molecules.

    Science.gov (United States)

    Yi, Chongyue; Dongare, Pratiksha D; Su, Man-Nung; Wang, Wenxiao; Chakraborty, Debadi; Wen, Fangfang; Chang, Wei-Shun; Sader, John E; Nordlander, Peter; Halas, Naomi J; Link, Stephan

    2017-10-31

    Plasmon hybridization theory, inspired by molecular orbital theory, has been extremely successful in describing the near-field coupling in clusters of plasmonic nanoparticles, also known as plasmonic molecules. However, the vibrational modes of plasmonic molecules have been virtually unexplored. By designing precisely configured plasmonic molecules of varying complexity and probing them at the individual plasmonic molecule level, intramolecular coupling of acoustic modes, mediated by the underlying substrate, is observed. The strength of this coupling can be manipulated through the configuration of the plasmonic molecules. Surprisingly, classical continuum elastic theory fails to account for the experimental trends, which are well described by a simple coupled oscillator picture that assumes the vibrational coupling is mediated by coherent phonons with low energies. These findings provide a route to the systematic optical control of the gigahertz response of metallic nanostructures, opening the door to new optomechanical device strategies. Published under the PNAS license.

  5. A night with good vibrations

    CERN Multimedia

    2002-01-01

    Next week-end, the Geneva Science History Museum invites you to a Science Night under the banner of waves and vibrations. Scientists, artists and storytellers from more than forty institutes and local or regional associations will show that waves and vibrations form an integral part of our environment. You will be able to get in contact with the nature of waves through interactive exhibitions on sound and light and through hands-on demonstrations arranged in the Park of the Perle du Lac. On the CERN stand, you will be able to measure the speed of light with a bar of chocolate, and understand the scattering of waves with plastic ducks. Amazing, no? In addition to the stands, the Night will offer many other activities: reconstructions of experiments, a play, a concert of crystal glasses, an illuminated fountain, a house of spirits. More information Science Night, 6 and 7 July, Park of the Perle du Lac, Geneva

  6. Framing Autism: A Content Analysis of Five Major News Frames in U.S.-Based Newspapers.

    Science.gov (United States)

    Wendorf Muhamad, Jessica; Yang, Fan

    2017-03-01

    The portrayal of child autism-related news stories has become a serious issue in the United States, yet few studies address this from media framing perspective. To fill this gap in the literature, this study examined the applicability of a media framing scale (Semetko & Valkenburg, 2000) for the deductive examination of autism-related news stories in U.S.-based newspapers. Under the theoretical framework of framing theory, a content analysis of news stories (N = 413) was conducted to investigate the presence of the five news frames using an established questionnaire. Differentiating between local and national news outlets, the following five news frames were measured: (a) attribution of responsibility, (b) human interest, (c) conflict, (d) morality, and (e) economic consequences. Findings revealed that news stories about autism most frequently fell within the human interest frame. Furthermore, the study shed light on how local and national newspapers might differ in framing autism-related news pieces and in their placement of the autism-related story within the newspaper (e.g., front page section, community section).

  7. Who's been framed? Framing effects are reduced in financial gambles made for others.

    Science.gov (United States)

    Ziegler, Fenja V; Tunney, Richard J

    2015-01-01

    Decisions made on behalf of other people are sometimes more rational than those made for oneself. In this study we used a monetary gambling task to ask if the framing effect in decision-making is reduced in surrogate decision-making. Participants made a series of choices between a predetermined sure option and a risky gambling option of winning a proportion of an initial stake. Trials were presented as either a gain or a loss relative to that initial stake. In half of the trials participants made choices to earn money for themselves and in the other half they earned money for another participant. Framing effects were measured as risk seeking in loss frames and risk aversion in gain frames. Significant framing effects were observed both in trials in which participants earned money for themselves and those in which they earned money for another person; however, these framing effects were significantly reduced when making decisions for another person. It appears that the reduced emotional involvement when the decision-maker is not affected by the outcome of the decision thus lessens the framing effect without eradicating it altogether. This suggests that the deviation from rational choices in decision-making can be significantly reduced when the emotional impact on the decision maker is lessened. These results are discussed in relation to Somatic Distortion Theory.

  8. Collective and single particle states in medium mass vibrational nuclei

    CERN Document Server

    Suliman, G

    2001-01-01

    The particle-core coupling model has been employed to describe the low lying nuclear excitations in the vibrational odd-A nuclei. In the frame of this model the following observables were calculated: excitation energies, spin and parity quantum numbers, electric quadrupole moments, magnetic dipole moments and reduced transition probabilities. Two computer codes were employed. The first one, PCOREC, diagonalized the Hamiltonian providing the eigenvectors and eigenvalues. The second one, PCORECTR, starts from the eigenvector computer by the first program and computes the observables which are compared we results of experiments. A good description of the experimental data has been obtained for the sup 1 sup 3 sup 3 Sb, sup 1 sup 2 sup 3 Sb and sup 1 sup 2 sup 5 Sb nuclei. (authors)

  9. Vibration control of a flexible structure with electromagnetic actuators

    DEFF Research Database (Denmark)

    Gruzman, Maurício; Santos, Ilmar

    2016-01-01

    This work presents the model of a shear-frame-type structure composed of six flexible beams and three rigid masses. Fixed on the ground, outside the structure, two voltage-controlled electromagnetic actuators are used for vibration control. To model the flexible beams, unidimensional finite...... elements were used. Nonlinear equations for the actuator electromagnetic force, noise in the position sensor, time delays for the control signal update and voltage saturation were also considered in the model. For controlling purposes, a discrete linear quadratic regulator combined with a predictive full......-order discrete linear observer was employed. Results of numerical simulations, where the structure is submitted to an impulsive disturbance force and to a harmonic force, show that the oscillations can be significantly reduced with the use of the electromagnetic actuators....

  10. Vibration Control in Periodic Structures

    DEFF Research Database (Denmark)

    Høgsberg, Jan Becker

    2017-01-01

    Within the framework of periodic structures, the calibration of RL shunted piezoelectric inclusions is investigated with respect to maximum damping of a particular wave form. A finite element setting is assumed, with local shunted inclusions inside the unit cell. The effect of the shunts is repre....... The presentation contains dispersion diagrams and vibration amplitude curves for the optimally calibrated RL shunt system in a 1-D periodic structure with local piezoelectric inclusions....

  11. Alignment dependent chemisorption of vibrationally excited CH4(?3) on Ni(100), Ni(110), and Ni(111)”

    OpenAIRE

    B. Yoder R. Bisson P. M. Hundt and R. Beck

    2011-01-01

    We present a stereodynamics study of the dissociative chemisorption of vibrationally excited methane on the (100) (110) and (111) planes of a nickel single crystal surface. Using linearly polarized infrared excitation of the antisymmetric C–H stretch normal mode vibration (? 3 ) we aligned the angular momentum and C–H stretch amplitude of CH4 (? 3 ) in the laboratory frame and measured the alignment dependence of stateresolved reactivity of CH4 for the ?3 = 1 J = 0–3 quantum states over a ran...

  12. Alignment dependent chemisorption of vibrationally excited CH4(3) on Ni(100), Ni(110), and Ni(111).

    OpenAIRE

    Yoder Bruce; Bisson Regis; Hundt Phil Morten; Beck Rainer D.

    2011-01-01

    We present a stereodynamics study of the dissociative chemisorption of vibrationally excited methane on the (100) (110) and (111) planes of a nickel single crystal surface. Using linearly polarized infrared excitation of the antisymmetric C–H stretch normal mode vibration (? 3 ) we aligned the angular momentum and C–H stretch amplitude of CH4 (? 3 ) in the laboratory frame and measured the alignment dependence of state resolved reactivity of CH4 for the ?3 = 1 J = 0–3 quantum states over a ra...

  13. Package security recorder of vibration

    Science.gov (United States)

    Wang, Xiao-na; Hu, Jin-liang; Song, Shi-de

    2013-08-01

    This paper introduces a new kind of electronic product — Package Security Recorder of Vibration. It utilizes STC89C54RD+ LQFP-44 MCU as its main controller. At the same time, it also utilizes Freescale MMA845A 3-Axis 8-bit/12-bit Digital Accelerometer and Maxim DS1302 Trickle Charge Timekeeping Chip. It utilizes the MCU to read the value of the accelerometer and the value of the timekeeping chip, and records the data into the inner E2PROM of MCU. The whole device achieves measuring, reading and recording the time of the vibration and the intensity of the vibration. When we need the data, we can read them out. The data can be used in analyzing the condition of the cargo when it transported. The device can be applied to monitor the security of package. It solves the problem of responsibility affirming, when the valuable cargo are damaged while it transported. It offers powerful safeguard for the package. It's very value for application.

  14. Uniformities and covering properties for partial frames (I

    Directory of Open Access Journals (Sweden)

    John Frith

    2014-07-01

    Full Text Available Partial frames provide a rich context in which to do pointfree structured and unstructured topology. A small collection of axioms of an elementary nature allows one to do much traditional pointfree topology, both on the level of frames or locales, and that of uniform or metric frames. These axioms are sufficiently general to include as examples bounded distributive lattices, $sigma$-frames, $kappa$-frames and frames.  Reflective subcategories of uniform and nearness spaces and lately coreflective subcategories of uniform and nearness frames have been a topic of considerable interest. In cite{jfas9} an easily implementable criterion for establishing certain coreflections in nearness frames was presented. Although the primary application in that paper was in the setting of nearness frames, it was observed there that similar techniques apply in many categories; we establish here, in this more general setting of structured partial frames, a technique that unifies these. We make use of the notion of a partial frame, which is a meet-semilattice in which certain designated subsets are required to have joins, and finite meets distribute over these. After presenting our axiomatization of partial frames, which we call $sels$-frames, we add structure, in the form of $sels$-covers and nearness, and provide the promised method of constructing certain coreflections. We illustrate the method with the examples of uniform, strong and totally bounded nearness $sels$-frames.  In Part (II of this paper, we consider regularity, normality and compactness for partial frames.

  15. Capacidade de produção e consumo específico de energia em picadoras forrageiras tipo desintegrador/picador/moedor Production capacity and specific energy consumption in forage choppers of the disintegrator/ chopper/grinder type

    Directory of Open Access Journals (Sweden)

    Luiz H. de Souza

    2009-02-01

    Full Text Available Avaliaram-se a capacidade de produção e o consumo específico de energia em picadoras de forragem tipo Desintegrador/Picador/Moedor no processamento de capim-elefante considerando-se, como tratamentos, três picadoras (DPM-1, DPm-2 e DPM-4, cinco diferentes rotações, três ângulos oblíquos das facas e dois ângulos do gume das facas. O delineamento experimental foi o inteiramente casualizado com duas repetições e os resultados avaliados por meio da análise de regressão. O ângulo oblíquo de 10º propiciou, aos três DPMs, maior eficiência e, em algumas situações o ângulo oblíquo de 38º proporcionou melhor desempenho aos DPMs 1 e 2; enquanto em outras, o ângulo de 30º proporcionou ao DPM-4, melhor desempenho. É possível baixar o custo de produção quando se trabalha em menores rotações, em virtude do valor do consumo específico ser reduzido. Embora o DPM-4 tenha apresentado menor demanda energética, ressalta-se que esta máquina possui maior preço de aquisição que os outros dois modelos e maior dificuldade de alimentação, obrigando o produtor a contratar mais uma pessoa para executar este processo.The production capacity and specific energy consumption in forage choppers type Disintegrator/Chopper/Grinder for elephant grass processing were evaluated. The treatments consisted of the combination of three forage choppers (DPM-1, DPm-2 and DPM-4, each operating in five different rotations, three oblique angles of the knives and two angles of the knives' edges. The experimental design used was completely randomized with two repetitions, and the results were evaluated by means of the regression analysis. The oblique angle of 10º led to greater efficiency for the three DPMs. In some situations, the oblique angle of 38º provided better performance for DPMs 1 and 2, while in others, the angle of 30º provided better performance for DPM-4. It is possible to lower production costs, when working at lower rotation speeds, due

  16. Analysis of Vibration and Acoustic Noise in Permanent Magnet Motors.

    Science.gov (United States)

    Hwang, Sangmoon

    . The effect of various design parameters on the output torque and torque ripple are discussed. Design parameters include winding patterns, magnetization direction, magnet arc length, number of segments in poles and magnet pole shaping. New designs of trapezoidal BEMF motors are proposed to reduce the electromagnetic torque ripple. Magnet stepping and magnet edge shaping with reduced arc length, significantly reduce torque ripple, with minimal sacrifice of the maximum output torque. Acoustic noise of electromagnetic origin is investigated using a magnetic frame which emulates a DC motor. The driving electromagnetic force is calculated using finite element analysis and the resulting vibration and acoustic noise is measured. Acoustic noise of purely electromagnetic origin was also tested with a DC brushless motor to confirm the results of the magnetic frame. The mechanism of noise generation in a DC motor is a quasi-static response of a stator not only at the fundamental frequency but also at higher harmonic frequencies of alternating switched DC, which is a current characteristic of a DC motor. Noise generation is significantly aggravated when some of those harmonics are close to the resonant frequencies of the stator. Therefore, acoustic noise is highly dependent upon the excitation current shape, as higher harmonics may match with resonant frequencies of the stator.

  17. Dynamics and Control of Lateral Tower Vibrations in Offshore Wind Turbines by Means of Active Generator Torque

    Directory of Open Access Journals (Sweden)

    Zili Zhang

    2014-11-01

    Full Text Available Lateral tower vibrations of offshore wind turbines are normally lightly damped, and large amplitude vibrations induced by wind and wave loads in this direction may significantly shorten the fatigue life of the tower. This paper proposes the modeling and control of lateral tower vibrations in offshore wind turbines using active generator torque. To implement the active control algorithm, both the mechanical and power electronic aspects have been taken into consideration. A 13-degrees-of-freedom aeroelastic wind turbine model with generator and pitch controllers is derived using the Euler–Lagrangian approach. The model displays important features of wind turbines, such as mixed moving frame and fixed frame-defined degrees-of-freedom, couplings of the tower-blade-drivetrain vibrations, as well as aerodynamic damping present in different modes of motions. The load transfer mechanisms from the drivetrain and the generator to the nacelle are derived, and the interaction between the generator torque and the lateral tower vibration are presented in a generalized manner. A three-dimensional rotational sampled turbulence field is generated and applied to the rotor, and the tower is excited by a first order wave load in the lateral direction. Next, a simple active control algorithm is proposed based on active generator torques with feedback from the measured lateral tower vibrations. A full-scale power converter configuration with a cascaded loop control structure is also introduced to produce the feedback control torque in real time. Numerical simulations have been carried out using data calibrated to the referential 5-MW NREL (National Renewable Energy Laboratory offshore wind turbine. Cases of drivetrains with a gearbox and direct drive to the generator are considered using the same time series for the wave and turbulence loadings. Results show that by using active generator torque control, lateral tower vibrations can be significantly mitigated for

  18. Buckling and vibration analysis of laminated panels using VICONOPT

    Science.gov (United States)

    Kennedy, David; Williams, Fred W.; Anderson, Melvin S.

    1994-01-01

    The analysis aspects of the 23,000-line FORTRAN program VIPASA with constraints and optimization (VICONOPT) are described. Overall stiffness matrices assembled from the earlier exact vibration and instability of plate assemblies including shear and anisotropy (VIPASA) flat plate stiffnesses are optionally coupled by Langrangian multipliers to find critical buckling loads, or natural frequencies of undamped vibration, of prismatic assemblies of anisotropic flat plates with arbitrarily located point supports or simple transverse supporting frames. The longitudunal continuity of typical wing and fuselage panels is closely approximated because the solutions are for the infinitely long structure obtained by repeating a bay and its supports longitudinally. Any longitudinally invariant in-plane plate stresses are permitted, and very rapid solutions are guaranteed by numerous refinements, including multilevel substructuring and a method for repetitive cross sections that is exact for regular polygons used to represent cylinders. Modal displacements and stresses in or between plies of laminated plates are calculated and plotted, with values being recovered at all nodes of substructures. Comparison with usual approximate finite-element methods confirms that, for comparably converged solutions, VICONOPT is typically between 100 and 10(exp 4) times faster.

  19. Mode shape analysis using a commercially available peak store video frame buffer

    Science.gov (United States)

    Snow, Walter L.; Childers, Brooks A.

    1994-01-01

    Time exposure photography, sometimes coupled with strobe illumination, is an accepted method for motion analysis that bypasses frame by frame analysis and resynthesis of data. Garden variety video cameras can now exploit this technique using a unique frame buffer that is a non-integrating memory that compares incoming data with that already stored. The device continuously outputs an analog video signal of the stored contents which can then be redigitized and analyzed using conventional equipment. Historically, photographic time exposures have been used to record the displacement envelope of harmonically oscillating structures to show mode shape. Mode shape analysis is crucial, for example, in aeroelastic testing of wind tunnel models. Aerodynamic, inertial, and elastic forces can couple together leading to catastrophic failure of a poorly designed aircraft. This paper will explore the usefulness of the peak store device as a videometric tool and in particular discuss methods for analyzing a targeted vibrating plate using the 'peak store' in conjunction with calibration methods familiar to the close-range videometry community. Results for the first three normal modes will be presented.

  20. Aerial Photo Single Frames = Frame Level Records for Multiple Agencies: 1937-Present

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — The Aerial Photography Single Frame Records collection is a large and diverse group of imagery acquired by Federal organizations from 1937 to the present. Over 6.4...

  1. Framing violence: the effect of survey context and question framing on reported rates of partner violence

    OpenAIRE

    Regan, Katherine V.

    2008-01-01

    In this dissertation, I investigated two explanations for the variability in levels of partner violence found by large community surveys. In Study 1, I examined the effect of how questions about partner violence are introduced (question framing: conflict, violence-in-relationships, or attacks) on reports of partner violence. Although there was not a reliable effect of question framing, the pattern of findings was consistent across 3 of 4 analyses. Counter to predictions, an attacks question f...

  2. News framing of cannabis: A quantitative exploratory study from the framing theory

    OpenAIRE

    Carlos Antonio Ballesteros Herencia

    2014-01-01

    The journalistic coverage of cannabis, the most used drug of restricted trade in the world, has stimulated a debate about its effects. However, there is a lack of research about the media information on cannabis, and the only official report published in Spain about this matter is not written by journalism experts. In order to contribute to overcome this state, an exploratory content analysis was carried out, adopting the framing theory as a basis. Previous framing researches were applied to ...

  3. Actively controlled vibration welding system and method

    Science.gov (United States)

    Cai, Wayne W.; Kang, Bongsu; Tan, Chin-An

    2013-04-02

    A vibration welding system includes a controller, welding horn, an active material element, and anvil assembly. The assembly may include an anvil body connected to a back plate and support member. The element, e.g., a piezoelectric stack or shape memory alloy, is positioned with respect to the assembly. The horn vibrates in a desirable first direction to form a weld on a work piece. The element controls any vibrations in a second direction by applying calibrated response to the anvil body in the second direction. A method for controlling undesirable vibrations in the system includes positioning the element with respect to the anvil assembly, connecting the anvil body to the support member through the back plate, vibrating the horn in a desirable first direction, and transmitting an input signal to the element to control vibration in an undesirable second direction.

  4. Coupled rotor/airframe vibration analysis

    Science.gov (United States)

    Sopher, R.; Studwell, R. E.; Cassarino, S.; Kottapalli, S. B. R.

    1982-01-01

    A coupled rotor/airframe vibration analysis developed as a design tool for predicting helicopter vibrations and a research tool to quantify the effects of structural properties, aerodynamic interactions, and vibration reduction devices on vehicle vibration levels is described. The analysis consists of a base program utilizing an impedance matching technique to represent the coupled rotor/airframe dynamics of the system supported by inputs from several external programs supplying sophisticated rotor and airframe aerodynamic and structural dynamic representation. The theoretical background, computer program capabilities and limited correlation results are presented in this report. Correlation results using scale model wind tunnel results show that the analysis can adequately predict trends of vibration variations with airspeed and higher harmonic control effects. Predictions of absolute values of vibration levels were found to be very sensitive to modal characteristics and results were not representative of measured values.

  5. Students' epistemological framing in quantum mechanics problem solving

    Science.gov (United States)

    Modir, Bahar; Thompson, John D.; Sayre, Eleanor C.

    2017-12-01

    Students' difficulties in quantum mechanics may be the result of unproductive framing and not a fundamental inability to solve the problems or misconceptions about physics content. We observed groups of students solving quantum mechanics problems in an upper-division physics course. Using the lens of epistemological framing, we investigated four frames in our observational data: algorithmic math, conceptual math, algorithmic physics, and conceptual physics. We discuss the characteristics of each frame as well as causes for transitions between different frames, arguing that productive problem solving may occur in any frame as long as students transition appropriately between frames. Our work extends epistemological framing theory on how students frame discussions in upper-division physics courses.

  6. Frame-Based Random Access with Interference Cancellation across Frames for Massive Machine Type Communications

    Directory of Open Access Journals (Sweden)

    Minjoong Rim

    2017-01-01

    Full Text Available One of the main requirements for next generation mobile or wireless communication systems is to effectively support a large number of machine type communication devices for Internet of things applications. In order to improve the random access capability in frame-based slotted Aloha environments, coded random access techniques have been proposed, in which multiple copies of a packet are transmitted per frame and the copies are cancelled out from the received signal if any single copy is successfully received. They, however, may increase the transmission power by sending multiple copies per frame. Above all, for systems with a small number of slots per frame, they may not be able to improve the performance by readily reaching a congested state. This paper proposes a new frame-based random access scheme, which sends at most one copy of a packet per frame but uses interference cancellation to improve the performance. If a successfully received packet is a retransmitted one, the previously transmitted signals for the packet can be cancelled out from the received signals for trying to decode other received packets. The proposed scheme has different characteristics than coded random access schemes and can be also combined with them to further improve the performance.

  7. Framing crime: moral panic in Argentine newspapers

    Directory of Open Access Journals (Sweden)

    Natalia ARUGUETE

    2013-01-01

    Full Text Available Carolina Píparo was shot a few minutes after withdrawing cash from a bank branch. This case outraged the public opinion because she was eight months pregnant at the moment of the assault. She had to undergo a caesarean section and her baby only survived one week. Through an exploratory and inductive research we will analyze how the Argentine newspapers presented the case. We aim at elaborating a content analysis code book that can be validated in future similar researches on the subject. We apply the Framing theory in order to detect the frames used in the news coverage and to observe if they are compatible with the idea of «moral panic» proposed by Stanley Cohen.

  8. Framing Trust at the Street-Level

    DEFF Research Database (Denmark)

    Perry, Kevin Anthony

    such as injustice and justice to create both distrust and trust frames around individual employees. The last analytical chapter reports finding four: negotiating cultural frames. The last part of the chapter looks closer at the relationship between the young men with minority ethnic backgrounds, the job consultant......This thesis deals with the phenomenon of distrust and trust between young men with minority ethnic backgrounds and public sector employees at the face-to-face level of interaction. The focus is on trust and distrust which can be understood as cultural resources – a valuable approach to researching...... trust and distrust largely under-represented in the trust literature. A common source of conflict is often a lack of confidence or distrust in the authorities; therefore, winning the confidence of minority ethnic groups in these communities is essential to easing tensions, along with reducing civil...

  9. Framing Trust at the Street-Level

    DEFF Research Database (Denmark)

    Perry, Kevin Anthony

    from analysing the aforementioned key government policy document. Next the thesis reports finding two: local authority institutionalised distrust frames. Through focusing on the ethnographic, this section explores the attitudes of some local authority actors towards a group of young men with minority...... unrest, antisocial behaviour, crime and unnecessary public spending. The purpose of this in-depth study, based on nine months of ethnographic fieldwork in and around two residential housing estates, is to contribute towards understanding the micro-processes at play in distrust and trust building...... into the wider cultural and structural context, while at the same time, contributes towards explaining why some local authority actors use certain frames and not others when talking about the young men with minority ethnic backgrounds. A number of research questions have guided the process which revolves around...

  10. Framing Trust at the Street-Level

    DEFF Research Database (Denmark)

    Perry, Kevin Anthony

    unrest, antisocial behaviour, crime and unnecessary public spending. The purpose of this in-depth study, based on nine months of ethnographic fieldwork in and around two residential housing estates, is to contribute towards understanding the micro-processes at play in distrust and trust building...... and artefacts such as media and local authority reports. In addition to the empirical material, the study explores a key governmental policy to investigate how the (previous) government names and frames people with minority ethnic backgrounds. Analysing this policy helps to locate the fieldwork and interactants...... a researcher (outsider) first enters a field setting. Amongst other methodological issues, this chapter presents a theoretical discussion about the significance of trust in relation to the researcher entering the field. Subsequently, the thesis reports finding one: Governmental Distrust Frames, which derives...

  11. New approach to relativistic celestial reference frames

    Science.gov (United States)

    Minazzoli, Olivier

    2012-08-01

    The current IAU recommendations regarding relativistic reference frames are mainly based on the works of Brumberg and Kopeikin on one hand and Damour, Soffel and Xu on the other hand. However the current recommendations give the transformations between the barycentric and the local frames in one way only, while both direct and inverse transformations are needed, at least for completion, if not for practical purposes. In our work, we (S. Turyshev, V. Toth and I) give an alternative approach to the two previous ones considered in the IAU resolutions. Conversely to those, our method is not based on the so - called matching technique. Our main result lies in the fact that we got both the direct and the inverse transformation at the same time - allowing checking the consistency of both transformations. Here we describe the simple case with monopoles as sources. The full extended - bodies case will be presented elsewhere.

  12. An Autonomous Reference Frame for Relativistic GNSS

    CERN Document Server

    Kostić, Uroš; Carloni, Sante; Delva, Pacôme; Gomboc, Andreja

    2014-01-01

    Current GNSS systems rely on global reference frames which are fixed to the Earth (via the ground stations) so their precision and stability in time are limited by our knowledge of the Earth dynamics. These drawbacks could be avoided by giving to the constellation of satellites the possibility of constituting by itself a primary and autonomous positioning system, without any a priori realization of a terrestrial reference frame. Our work shows that it is possible to construct such a system, an Autonomous Basis of Coordinates, via emission coordinates. Here we present the idea of the Autonomous Basis of Coordinates and its implementation in the perturbed space-time of Earth, where the motion of satellites, light propagation, and gravitational perturbations are treated in the formalism of general relativity.

  13. Trust and Distrust as Cultural Frames

    DEFF Research Database (Denmark)

    Perry, Kevin Anthony

    2016-01-01

    ’ implies that individuals respond actively to unfolding events in the context and modify their responses to meet changes in circumstances. Within a process perspective, this chapter looks closely at the relationships between a group of young men with minority ethnic backgrounds, a team of youth workers......, a job consultant and a police officer, to shed light on trust- and distrust-building processes. This chapter addresses the frames used by the young men to organize public sector employees, either as trusting or distrusting, together with some of the cultural tools used to construct these frames. The key....... The chapter contributes towards understanding of the micro-processes at play in trust- and distrust-building processes....

  14. Physics within a quantum reference frame

    OpenAIRE

    Angelo, Renato M.; Brunner, Nicolas; Popescu, Sandu; Short, Anthony J.; Skrzypczyk, Paul

    2010-01-01

    We investigate the physics of quantum reference frames. Specifically, we study several simple scenarios involving a small number of quantum particles, whereby we promote one of these particles to the role of a quantum observer and ask what is the description of the rest of the system, as seen by this observer? We highlight the interesting aspects of such questions by presenting a number of apparent paradoxes. By unravelling these paradoxes we get a better understanding of the physics of quant...

  15. HEALTH INSURANCE Spectacle frame reimbursement ceiling

    CERN Multimedia

    HR Division

    2001-01-01

    As from 1st January 2001, the three-year reimbursement ceiling for spectacle frames is replaced by annual ceilings which may be cumulated for a maximum of three years. The calculation method is therefore different from the one applied until 2000. A special procedure is applied to the transition between these two methods. Details of those procedures are published in an information sheet made available from divisional secretariats and at the UNIQA office at CERN.

  16. Wood-framed houses for earthquake zones

    DEFF Research Database (Denmark)

    Hansen, Klavs Feilberg

    Wood-framed houses with a sheathing are suitable for use in earthquake zones. The Direction describes a method of determining the earthquake forces in a house and shows how these forces can be resisted by diaphragm action in the walls, floors, and roof, of the house. An appendix explains how...... to design the wall, roof, and floor panels. The Direction is intended for design engineers and architects....

  17. Frames of reference in spatial language acquisition.

    Science.gov (United States)

    Shusterman, Anna; Li, Peggy

    2016-08-01

    Languages differ in how they encode spatial frames of reference. It is unknown how children acquire the particular frame-of-reference terms in their language (e.g., left/right, north/south). The present paper uses a word-learning paradigm to investigate 4-year-old English-speaking children's acquisition of such terms. In Part I, with five experiments, we contrasted children's acquisition of novel word pairs meaning left-right and north-south to examine their initial hypotheses and the relative ease of learning the meanings of these terms. Children interpreted ambiguous spatial terms as having environment-based meanings akin to north and south, and they readily learned and generalized north-south meanings. These studies provide the first direct evidence that children invoke geocentric representations in spatial language acquisition. However, the studies leave unanswered how children ultimately acquire "left" and "right." In Part II, with three more experiments, we investigated why children struggle to master body-based frame-of-reference words. Children successfully learned "left" and "right" when the novel words were systematically introduced on their own bodies and extended these words to novel (intrinsic and relative) uses; however, they had difficulty learning to talk about the left and right sides of a doll. This difficulty was paralleled in identifying the left and right sides of the doll in a non-linguistic memory task. In contrast, children had no difficulties learning to label the front and back sides of a doll. These studies begin to paint a detailed account of the acquisition of spatial terms in English, and provide insights into the origins of diverse spatial reference frames in the world's languages. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

  18. Investigating learners' epistemological framings of quantum mechanics

    Science.gov (United States)

    Dini, Vesal

    Classical mechanics challenges students to use their intuitions and experiences as a basis for understanding, in effect to approach learning as "a refinement of everyday thinking'' (Einstein, 1936). Moving on to quantum mechanics (QM), students, like physicists, need to adjust this approach, in particular with respect to the roles that intuitive knowledge and mathematics play in the pursuit of coherent understanding (these are adjustments to aspects of their epistemologies). In this dissertation, I explore how some students manage the epistemological transition. I began this work by recruiting both graduate and undergraduate students, interviewing each subject several times as they moved through coursework in QM. The interviews featured, among other things, how students tried to fit ideas together in mutually consistent ways, including with respect to intuitive knowledge, mathematics and experiment, if at all. I modeled these dynamic cognitive processes as different epistemological framings (i.e., tacit, in-the-moment responses to the question "How should I approach knowledge?''). Through detailed qualitative analyses of students' reasoning and a systematic coding of their interviews, I explored how these coherence seeking related framings impacted their learning. The dissertation supports three main findings: (1) students' patterns of epistemological framing are mostly stable within a given course; (2) students who profess epistemologies aligned with the coordination of coherence seeking framings tend to be more stable in demonstrating them; and (3) students aware that their understanding of QM ultimately anchors in its mathematics tend to produce more coherent explanations and perform better in their courses. These findings are consistent with existing research on student epistemologies in QM and imply that epistemologies, in particular whether and how students seek coherence, require greater attention and emphasis in instruction.

  19. High force vibration testing with wide frequency range

    Science.gov (United States)

    Romero, Edward F.; Jepsen, Richard A.; Gregory, Danny Lynn

    2013-04-02

    A shaker assembly for vibration testing includes first and second shakers, where the first shaker includes a piezo-electric material for generating vibration. A support structure permits a test object to be supported for vibration of the test object by both shakers. An input permits an external vibration controller to control vibration of the shakers.

  20. Simulation of a fast framing staring sensor

    Energy Technology Data Exchange (ETDEWEB)

    Jefferson, K.J.; Wickstrom, R.D.

    1998-04-01

    A sensor system simulation has been developed which aids in the evaluation of a proposed fast framing staring sensor as it will perform in its operational environment. Beginning with a high resolution input image, a sequence of frames at the target sensor resolution are produced using the assumed platform motion and the contribution of various noise sources as input data. The resulting frame sequence can then be used to help define system requirements, to aid algorithm development, and to predict system performance. In order to assess the performance of a sensor system, the radiance measured by the system is modeled using a variety of scenarios. For performance prediction, the modeling effort is directed toward providing the ability to determine the minimum Noise Equivalent Target (NET) intensities for each band of the sensor system. The NET is calculated at the entrance pupil of the instrument in such a way that the results can be applied to a variety of point source targets and collection conditions. The intent is to facilitate further study within the user community as new mission areas and/or targets of interest develop that are not addressed explicitly during sensor conceptual design.