Alternatives to traditional transportation fuels 1993

Energy Technology Data Exchange (ETDEWEB)

1995-01-01

In recent years, gasoline and diesel fuel have accounted for about 80 percent of total transportation fuel and nearly all of the fuel used in on-road vehicles. Growing concerns about the environmental effects of fossil fuel use and the Nation`s high level of dependence on foreign oil are providing impetus for the development of replacements or alternatives for these traditional transportation fuels. (The Energy Policy Act of 1992 definitions of {open_quotes}replacement{close_quotes} and {open_quotes}alternative{close_quotes} fuels are presented in the following box.) The Alternative Motor Fuels Act of 1988, the Clean Air Act Amendments of 1990 (CAAA90) and the Energy Policy Act of 1992 (EPACT) are significant legislative forces behind the growth of replacement fuel use. Alternatives to Traditional Transportation Fuels 1993 provides the number of on-road alternative fueled vehicles in use in the United States, alternative and replacement fuel consumption, and information on greenhouse gas emissions resulting from the production, delivery, and use of replacement fuels for 1992, 1993, and 1995.

Standardization of Alternative Fuels. Phase 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-08-15

There are different interpretations of the term 'alternative fuels', depending on the part of the world in which the definition is used. In this report, alternative fuels mainly stand for fuels that can replace gasoline and diesel oil and at the same time contribute to lowered emissions with impact on health, environment and climate. The use of alternative vehicle fuels has increased during the last 30 years. However, the increase has developed slowly and today the use is very limited, compared to the use of conventional fuels. Although, the use in some special applications, often in rather small geographical areas, can be somewhat larger. The main interest for alternative fuels has for a long time been driven by supply security issues and the possibility to reduce emissions with a negative impact on health and environment. However, the development of reformulated gasoline and low sulphur diesel oil has contributed to substantially decreased emissions from these fuels without using any alternative fuel. This has reduced the environmental impact driving force for the introduction of alternative fuels. In line with the increased interest for climate effects and the connections between these effects and the emission of greenhouse gases, and then primarily carbon dioxide, the interest for biomass based alternative fuels has increased during the 1990s. Even though one of the driving forces for alternative fuels is small today, alternative fuels are more commonly accepted than ever before. The European Commission has for example in May 2003 agreed on a directive for the promotion of the use of bio fuels. In the directive there are goals for the coming 7 years that will increase the use of alternative fuels in Europe rather dramatically, from below 1 percent now up to almost 6 percent of the total vehicle fuel consumption in 2010. The increased use of alternative fuels in Europe and the rest of the world will create a need for a common interpretation of what we

A methodology for assessing the market benefits of alternative motor fuels: The Alternative Fuels Trade Model

Energy Technology Data Exchange (ETDEWEB)

Leiby, P.N.

1993-09-01

This report describes a modeling methodology for examining the prospective economic benefits of displacing motor gasoline use by alternative fuels. The approach is based on the Alternative Fuels Trade Model (AFTM). AFTM development was undertaken by the US Department of Energy (DOE) as part of a longer term study of alternative fuels issues. The AFTM is intended to assist with evaluating how alternative fuels may be promoted effectively, and what the consequences of substantial alternative fuels use might be. Such an evaluation of policies and consequences of an alternative fuels program is being undertaken by DOE as required by Section 502(b) of the Energy Policy Act of 1992. Interest in alternative fuels is based on the prospective economic, environmental and energy security benefits from the substitution of these fuels for conventional transportation fuels. The transportation sector is heavily dependent on oil. Increased oil use implies increased petroleum imports, with much of the increase coming from OPEC countries. Conversely, displacement of gasoline has the potential to reduce US petroleum imports, thereby reducing reliance on OPEC oil and possibly weakening OPEC`s ability to extract monopoly profits. The magnitude of US petroleum import reduction, the attendant fuel price changes, and the resulting US benefits, depend upon the nature of oil-gas substitution and the supply and demand behavior of other world regions. The methodology applies an integrated model of fuel market interactions to characterize these effects.

Contracting of energy services: often a viable alternative

International Nuclear Information System (INIS)

Milic, M.; Bruendler, M.

2001-01-01

This article discusses the outsourcing of energy services as a viable alternative to the operation of own energy facilities. The advantages of contracting for enterprises wanting to focus on their core competencies and have their energy infrastructure financed, built, maintained and operated by a third party are discussed. Financial aspects are looked at and examples in connection with the calculation of actual energy costs are given. The article is concluded with tips on the evaluation of offers for contracting services and on the definition of ownership aspects and property boundaries

Alternatives to traditional transportation fuels: An overview

Energy Technology Data Exchange (ETDEWEB)

1994-06-01

This report presents the first compilation by the Energy Information Administration (EIA) of information on alternatives to gasoline and diesel fuel. The purpose of the report is: (1) to provide background information on alternative transportation fuels and replacement fuels compared with gasoline and diesel fuel, and (2) to furnish preliminary estimates of alternative transportation fuels and alternative fueled vehicles as required by the Energy Policy Act of 1992 (EPACT), Title V, Section 503, ``Replacement Fuel Demand Estimates and Supply Information.`` Specifically, Section 503 requires the EIA to report annually on: (1) the number and type of alternative fueled vehicles in existence the previous year and expected to be in use the following year, (2) the geographic distribution of these vehicles, (3) the amounts and types of replacement fuels consumed, and (4) the greenhouse gas emissions likely to result from replacement fuel use. Alternative fueled vehicles are defined in this report as motorized vehicles licensed for on-road use, which may consume alternative transportation fuels. (Alternative fueled vehicles may use either an alternative transportation fuel or a replacement fuel.) The intended audience for the first section of this report includes the Secretary of Energy, the Congress, Federal and State agencies, the automobile manufacturing industry, the transportation fuel manufacturing and distribution industries, and the general public. The second section is designed primarily for persons desiring a more technical explanation of and background for the issues surrounding alternative transportation fuels.

ALTERNATIVE FUELS FOR DIESEL ENGINES

Directory of Open Access Journals (Sweden)

Jacek Caban

2013-12-01

Full Text Available This paper presents the development and genesis of the use of alternative fuels in internal combustion ignition engines. Based on the analysis of the literature, this article shows various alternative fuels used in Poland and all over the world. Furthermore, this article describes the research directions for alternative fuels use in road transport powered by diesel engines.

Alternative transportation fuels: Financing issues

International Nuclear Information System (INIS)

Squadron, W.F.; Ward, C.O.; Brown, M.H.

1992-06-01

A multitude of alternative fuels could reduce air pollution and the impact of oil price shocks. Only a few of these fuels are readily available and inexpensive enough to merit serious consideration over the coming five years. In New York City, safety regulations narrow the field still further by eliminating propane. As a result, this study focuses on the three alternative fuels readily available in New York City: compressed natural gas, methanol, and electricity. Each has significant environmental benefits and each has different cost characteristics. With the Clean Air Act and the National Energy Strategy highlighting the country's need to improve urban air quality and move away from dependence on imported fuels, fleets may soon have little choice but to convert to altemative fuels. Given the potential for large infrastructure and vehicle costs, these fleets may have difficulty finding the capital to make that conversion. Ultimately, then, it will be the involvement of the private sector that will determine the success of alternative fuels. Whether it be utilities, fuel distributors or suppliers, private financing partners or others, it is critical that altemative fuels programs be structured and planned to attract their involvement. This report examines financing methods that do not involve government subsidies. It also explores financing methods that are specific to alternative fuels. Bond issues and other mechanisms that are used for conventional vehicles are not touched upon in this report. This report explores ways to spread the high cost of alternative fuels among a number of parties within the private sector. The emphasis is on structuring partnerships that suit methanol, electric, or natural gas vehicle fleets. Through these partnerships, alternative fuels may ultimately compete effectively against conventional vehicle fuels

Alternative Fuels Data Center: Biodiesel Equipment Options

Science.gov (United States)

Equipment Options to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Equipment Options on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Equipment Options on Twitter Bookmark Alternative Fuels Data Center: Biodiesel Equipment Options on Google Bookmark Alternative Fuels

Alternative Fuels Data Center: Biodiesel Benefits

Science.gov (United States)

, and transport. Maps & Data U.S. Biodiesel Production, Exports, and Consumption U.S. Biodiesel Benefits to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Benefits on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Benefits on Twitter Bookmark Alternative Fuels Data

Alternative Fuels Data Center: Natural Gas Benefits

Science.gov (United States)

Benefits to someone by E-mail Share Alternative Fuels Data Center: Natural Gas Benefits on Facebook Tweet about Alternative Fuels Data Center: Natural Gas Benefits on Twitter Bookmark Alternative Fuels Data Center: Natural Gas Benefits on Google Bookmark Alternative Fuels Data Center: Natural Gas

Alternative Fuels Data Center: Krug Energy Opens Natural Gas Fueling

Science.gov (United States)

Station in Arkansas Krug Energy Opens Natural Gas Fueling Station in Arkansas to someone by E -mail Share Alternative Fuels Data Center: Krug Energy Opens Natural Gas Fueling Station in Arkansas on Facebook Tweet about Alternative Fuels Data Center: Krug Energy Opens Natural Gas Fueling Station in

Alternative Fuels Data Center: Indiana Transportation Data for Alternative

Science.gov (United States)

(nameplate, MW) 1,430 Source: BioFuels Atlas from the National Renewable Energy Laboratory Case Studies Video Alternative Fuels Save Money in Indy April 1, 2012 More Case Studies Videos Text Version More Indiana Videos on YouTube Video thumbnail for Indiana Beverage Company Invests in Alternative Fuels Indiana Beverage

16 CFR 309.10 - Alternative vehicle fuel rating.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Alternative vehicle fuel rating. 309.10... LABELING REQUIREMENTS FOR ALTERNATIVE FUELS AND ALTERNATIVE FUELED VEHICLES Requirements for Alternative Fuels Duties of Importers, Producers, and Refiners of Non-Liquid Alternative Vehicle Fuels (other Than...

Advanced Technology and Alternative Fuel Vehicles

International Nuclear Information System (INIS)

Tuttle, J.

2001-01-01

This fact sheet provides a basic overview of today's alternative fuel choices--including biofuels, biodiesel, electricity, and hydrogen--alternative fuel vehicles, and advanced vehicle technology, such as hybrid electric vehicles, fuel cells and advanced drive trains

Alternative Fuels Data Center: Natural Gas Vehicles

Science.gov (United States)

Natural Gas Printable Version Share this resource Send a link to Alternative Fuels Data Center : Natural Gas Vehicles to someone by E-mail Share Alternative Fuels Data Center: Natural Gas Vehicles on Facebook Tweet about Alternative Fuels Data Center: Natural Gas Vehicles on Twitter Bookmark Alternative

Alternative Fuel News, Vol. 6, No. 4

Energy Technology Data Exchange (ETDEWEB)

2003-03-01

Quarterly magazine with articles on Alternate Fuel Vehicles (AFVs) in India, alternative fuels for emergency preparedness, and testing of propane vehicles by UPS. Also an interview of author Jeremy Rifkin on how alternative fuels provide pathways to hydrogen.

Alternative Fuels Data Center: Publications

Science.gov (United States)

Windstars; 14) and the use of alternative fuel vehicles at the Olympics. Alternative Fuels In Trucking, Vol and their economic and environmental benefits. This report is designed to share the experiences and National Academy of Engineering suggested that 'DOE might have its greatest impact by leading the private

Commercial aviation alternative fuels initiative

Science.gov (United States)

2010-04-22

This presentation looks at alternative fuels to enhance environmental stability, reduction of greenhouse gas emissions, air quality benefits (e.g., SOx and PM), fuel supply stability, and fuel price stability.

Alternative Aviation Fuel Experiment (AAFEX)

Science.gov (United States)

Anderson, B. E.; Beyersdorf, A. J.; Hudgins, C. H.; Plant, J. V.; Thornhill, K. L.; Winstead, E. L.; Ziemba, L. D.; Howard, R.; Corporan, E.; Miake-Lye, R. C.;

Special Issue: Aviation Alternative Fuels

Directory of Open Access Journals (Sweden)

Yang Zhang

2014-12-01

Full Text Available The investigation of aviation alternative fuels has increased significantly in recent years in an effort to reduce the environment and climate impact by aviation industry. Special requirements have to be met for qualifying as a suitable aviation fuel. The fuel has to be high in energy content per unit of mass and volume, thermally stable and avoiding freezing at low temperatures. There are also many other special requirements on viscosity, ignition properties and compatibility with the typical aviation materials. There are quite a few contending alternative fuels which can be derived from coal, natural gas and biomass.[...

A life-cycle comparison of alternative automobile fuels.

Science.gov (United States)

MacLean, H L; Lave, L B; Lankey, R; Joshi, S

2000-10-01

We examine the life cycles of gasoline, diesel, compressed natural gas (CNG), and ethanol (C2H5OH)-fueled internal combustion engine (ICE) automobiles. Port and direct injection and spark and compression ignition engines are examined. We investigate diesel fuel from both petroleum and biosources as well as C2H5OH from corn, herbaceous bio-mass, and woody biomass. The baseline vehicle is a gasoline-fueled 1998 Ford Taurus. We optimize the other fuel/powertrain combinations for each specific fuel as a part of making the vehicles comparable to the baseline in terms of range, emissions level, and vehicle lifetime. Life-cycle calculations are done using the economic input-output life-cycle analysis (EIO-LCA) software; fuel cycles and vehicle end-of-life stages are based on published model results. We find that recent advances in gasoline vehicles, the low petroleum price, and the extensive gasoline infrastructure make it difficult for any alternative fuel to become commercially viable. The most attractive alternative fuel is compressed natural gas because it is less expensive than gasoline, has lower regulated pollutant and toxics emissions, produces less greenhouse gas (GHG) emissions, and is available in North America in large quantities. However, the bulk and weight of gas storage cylinders required for the vehicle to attain a range comparable to that of gasoline vehicles necessitates a redesign of the engine and chassis. Additional natural gas transportation and distribution infrastructure is required for large-scale use of natural gas for transportation. Diesel engines are extremely attractive in terms of energy efficiency, but expert judgment is divided on whether these engines will be able to meet strict emissions standards, even with reformulated fuel. The attractiveness of direct injection engines depends on their being able to meet strict emissions standards without losing their greater efficiency. Biofuels offer lower GHG emissions, are sustainable, and

A Life-Cycle Comparison of Alternative Automobile Fuels.

Science.gov (United States)

MacLean, Heather L; Lave, Lester B; Lankey, Rebecca; Joshi, Satish

2000-10-01

We examine the life cycles of gasoline, diesel, compressed natural gas (CNG), and ethanol (C 2 H 5 OH)-fueled internal combustion engine (ICE) automobiles. Port and direct injection and spark and compression ignition engines are examined. We investigate diesel fuel from both petroleum and biosources as well as C 2 H 5 OH from corn, herbaceous bio-mass, and woody biomass. The baseline vehicle is a gasoline-fueled 1998 Ford Taurus. We optimize the other fuel/powertrain combinations for each specific fuel as a part of making the vehicles comparable to the baseline in terms of range, emissions level, and vehicle lifetime. Life-cycle calculations are done using the economic input-output life-cycle analysis (EIO-LCA) software; fuel cycles and vehicle end-of-life stages are based on published model results. We find that recent advances in gasoline vehicles, the low petroleum price, and the extensive gasoline infrastructure make it difficult for any alternative fuel to become commercially viable. The most attractive alternative fuel is compressed natural gas because it is less expensive than gasoline, has lower regulated pollutant and toxics emissions, produces less greenhouse gas (GHG) emissions, and is available in North America in large quantities. However, the bulk and weight of gas storage cylinders required for the vehicle to attain a range comparable to that of gasoline vehicles necessitates a redesign of the engine and chassis. Additional natural gas transportation and distribution infrastructure is required for large-scale use of natural gas for transportation. Diesel engines are extremely attractive in terms of energy efficiency, but expert judgment is divided on whether these engines will be able to meet strict emissions standards, even with reformulated fuel. The attractiveness of direct injection engines depends on their being able to meet strict emissions standards without losing their greater efficiency. Biofuels offer lower GHG emissions, are sustainable

Global Energy Issues and Alternate Fueling

Science.gov (United States)

Hendricks, Robert C.

2007-01-01

This viewgraph presentation describes world energy issues and alternate fueling effects on aircraft design. The contents include: 1) US Uses about 100 Quad/year (1 Q = 10(exp 15) Btu) World Energy Use: about 433 Q/yr; 2) US Renewable Energy about 6%; 3) Nuclear Could Grow: Has Legacy Problems; 4) Energy Sources Primarily NonRenewable Hydrocarbon; 5) Notes; 6) Alternate Fuels Effect Aircraft Design; 7) Conventional-Biomass Issue - Food or Fuel; 8) Alternate fuels must be environmentally benign; 9) World Carbon (CO2) Emissions Problem; 10) Jim Hansen s Global Warming Warnings; 11) Gas Hydrates (Clathrates), Solar & Biomass Locations; 12) Global Energy Sector Response; 13) Alternative Renewables; 14) Stratospheric Sulfur Injection Global Cooling Switch; 15) Potential Global Energy Sector Response; and 16) New Sealing and Fluid Flow Challenges.

Alternative Fuel News: Official Publication of the Clean Cities Network and the Alternative Fuels Data Center, Vol. 4, No. 2

Energy Technology Data Exchange (ETDEWEB)

Ficker, C.

2000-09-08

This issue of Alternative Fuel News discusses Executive Order 13149 which is designed to not only increase the use of alternative fuel by federal agencies but also to increase the use of fuel efficient vehicles in the federal fleet. Also highlighted is the 6th National Clean Cities Conference and Expo held in San Diego, May 7-10, 2000, which attracted nearly 1,000 people for three action-packed days of alternative fuel activities. The work to develop a market for alternative fuels is more important than ever.

Sulphur release from alternative fuel firing

DEFF Research Database (Denmark)

Cortada Mut, Maria del Mar; Nørskov, Linda Kaare; Glarborg, Peter

2014-01-01

The cement industry has long been dependent on the use of fossil fuels, although a recent trend in replacing fossil fuels with alternative fuels has arisen. 1, 2 However, when unconverted or partly converted alternative fuels are admitted directly in the rotary kiln inlet, the volatiles released...... from the fuels may react with sulphates present in the hot meal to form SO 2 . Here Maria del Mar Cortada Mut and associates describe pilot and industrial scale experiments focusing on the factors that affect SO 2 release in the cement kiln inlet....

Alternative Fuels Market and Policy Trends (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Schroeder, A. N.

2013-09-01

Market forces and policies are increasing opportunities for alternative fuels. There is no one-size-fits-all, catch-all, silver-bullet fuel. States play a critical role in the alternative fuel market and are taking a leading role.

Alcohol-fueled vehicles: An alternative fuels vehicle, emissions, and refueling infrastructure technology assessment

Energy Technology Data Exchange (ETDEWEB)

McCoy, G.A.; Kerstetter, J.; Lyons, J.K. [and others

1993-06-01

Interest in alternative motor vehicle fuels has grown tremendously over the last few years. The 1990 Clean Air Act Amendments, the National Energy Policy Act of 1992 and the California Clean Air Act are primarily responsible for this resurgence and have spurred both the motor fuels and vehicle manufacturing industries into action. For the first time, all three U.S. auto manufacturers are offering alternative fuel vehicles to the motoring public. At the same time, a small but growing alternative fuels refueling infrastructure is beginning to develop across the country. Although the recent growth in alternative motor fuels use is impressive, their market niche is still being defined. Environmental regulations, a key driver behind alternative fuel use, is forcing both car makers and the petroleum industry to clean up their products. As a result, alternative fuels no longer have a lock on the clean air market and will have to compete with conventional vehicles in meeting stringent future vehicle emission standards. The development of cleaner burning gasoline powered vehicles has signaled a shift in the marketing of alternative fuels. While they will continue to play a major part in the clean vehicle market, alternative fuels are increasingly recognized as a means to reduce oil imports. This new role is clearly defined in the National Energy Policy Act of 1992. The Act identifies alternative fuels as a key strategy for reducing imports of foreign oil and mandates their use for federal and state fleets, while reserving the right to require private and municipal fleet use as well.

Alternative Fuels Data Center: Conventional Natural Gas Production

Science.gov (United States)

Conventional Natural Gas Production to someone by E-mail Share Alternative Fuels Data Center : Conventional Natural Gas Production on Facebook Tweet about Alternative Fuels Data Center: Conventional Natural Gas Production on Twitter Bookmark Alternative Fuels Data Center: Conventional Natural Gas Production

Alternate-Fuel Vehicles and Their Application in Schools.

Science.gov (United States)

Taggart, Chip

1991-01-01

Alternative fuels are becoming increasingly attractive from environmental, energy independence, and economic perspectives. Addresses the following topics: (1) federal and state legislation; (2) alternative fuels and their attributes; (3) practical experience with alternative-fuel vehicles in pupil transportation; and (4) options for school…

Alternative Fuel News, Vol. 2, No. 7

Energy Technology Data Exchange (ETDEWEB)

NREL

1999-05-20

What's in store for alternative Fuels and advanced technology vehicles in the new millennium? The Clean Cities Coalitions now operate more than 240,000 alternative fuel vehicles in both public and private sectors and have access to more than 4,000 alternative refueling stations. DOE recently announced the selection of 15 proposals that will receive just under $1.7 million in financial assistance to help expand DOE's information dissemination and public outreach efforts for alternative fuels and advanced transportation technologies.

Alternatives to traditional transportation fuels 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

Interest in alternative transportation fuels (ATF`s) has increased in recent years due to the drives for cleaner air and less dependence upon foreign oil. This report, Alternatives to Traditional Transportation Fuels 1996, provides information on ATFs, as well as the vehicles that consume them.

Gas detection for alternate-fuel vehicle facilities.

Science.gov (United States)

Ferree, Steve

2003-05-01

Alternative fuel vehicles' safety is driven by local, state, and federal regulations in which fleet owners in key metropolitan [table: see text] areas convert much of their fleet to cleaner-burning fuels. Various alternative fuels are available to meet this requirement, each with its own advantages and requirements. This conversion to alternative fuels leads to special requirements for safety monitoring in the maintenance facilities and refueling stations. A comprehensive gas and flame monitoring system needs to meet the needs of both the user and the local fire marshal.

Canola Oil Fuel Cell Demonstration: Volume 2 - Market Availability of Agricultural Crops for Fuel Cell Applications

National Research Council Canada - National Science Library

Adams, John W; Cassarino, Craig; Spangler, Lee; Johnson, Duane; Lindstrom, Joel; Binder, Michael J; Holcomb, Franklin H; Lux, Scott M

2006-01-01

.... The reformation of vegetable oil crops for fuel cell uses is not well known; yet vegetable oils such as canola oil represent a viable alternative and complement to traditional fuel cell feedstocks...

Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel

Science.gov (United States)

Biodiesel Printable Version Share this resource Send a link to Alternative Fuels Data Center : Diesel Vehicles Using Biodiesel to someone by E-mail Share Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel on Facebook Tweet about Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel

Proceedings of the 1991 Windsor workshop on alternative fuels

International Nuclear Information System (INIS)

1991-01-01

A workshop was held to exchange information among engine and vehicle manufacturers, fuel suppliers, research organizations, and academic and regulatory bodies on various aspects of alternative transportation fuels development. Papers were presented on alternative fuels policies and programs, zero-emission vehicles, emission control technologies, field evaluations of alternative fuel systems, and heavy duty alternate-fuel engines. Separate abstracts have been prepared for nine papers from this workshop

Enabling alternate fuels for commercial aircraft

OpenAIRE

Daggett, D.

2010-01-01

The following reports on the past four years of work to examine the feasibility, sustainability and economic viability of developing a renewable, greenhouse-gas-neutral, liquid biofuel for commercial aircraft. The sharp increase in environmental concerns, such as global warming, as well as the volatile price fluctuations of fossil fuels, has ignited a search for alternative transportation fuels. However, commercial aircraft can not use present alternative fuels that are designed for ground...

Castor oil biodiesel and its blends as alternative fuel

International Nuclear Information System (INIS)

Berman, Paula; Nizri, Shahar; Wiesman, Zeev

2011-01-01

Intensive production and commercialization of biodiesel from edible-grade sources have raised some critical environmental concerns. In order to mitigate these environmental consequences, alternative oilseeds are being investigated as biodiesel feedstocks. Castor (Ricinus communis L.) is one of the most promising non-edible oil crops, due to its high annual seed production and yield, and since it can be grown on marginal land and in semi-arid climate. Still, few studies are available regarding its fuel-related properties in its pure form or as a blend with petrodiesel, many of which are due to its extremely high content of ricinoleic acid. In this study, the specifications in ASTM D6751 and D7467 which are related to the fatty acid composition of pure castor methyl esters (B100) and its blend with petrodiesel in a 10% vol ratio (B10) were investigated. Kinematic viscosity and distillation temperature of B100 (15.17 mm 2 s -1 and 398.7 o C respectively) were the only two properties which did not meet the appropriate standard limits. In contrast, B10 met all the specifications. Still, ASTM D7467 requires that the pure biodiesel meets the requirements of ASTM D6751. This can limit the use of a wide range of feedstocks, including castor, as alternative fuel, especially due to the fact that in practice vehicles normally use low level blends of biodiesel and petrodiesel. These issues are discussed in depth in the present study. -- Highlights: → CaME can be used as a biodiesel alternative feedstock when blended in petrodiesel. → Due to the high levels of ricinoleic acid maximum blending level is limited to 10%. → Today, CaME blends are not a viable alternative feedstock. → ASTM D7467 requires that pure biodiesel must meet all the appropriate limits.

Alternative Fabrication of Recycling Fast Reactor Metal Fuel

International Nuclear Information System (INIS)

Kim, Ki-Hwan; Kim, Jong Hwan; Song, Hoon; Kim, Hyung-Tae; Lee, Chan-Bock

2015-01-01

Metal fuels such as U-Zr/U-Pu-Zr alloys have been considered as a nuclear fuel for a sodium-cooled fast reactor (SFR) related to the closed fuel cycle for managing minor actinides and reducing a high radioactivity levels since the 1980s. In order to develop innovative fabrication method of metal fuel for preventing the evaporation of volatile elements such as Am, modified casting under inert atmosphere has been applied for metal fuel slugs for SFR. Alternative fabrication method of fuel slugs has been introduced to develop an improved fabrication process of metal fuel for preventing the evaporation of volatile elements. In this study, metal fuel slugs for SFR have been fabricated by modified casting method, and characterized to evaluate the feasibility of the alternative fabrication method. In order to prevent evaporation of volatile elements such as Am and improve quality of fuel slugs, alternative fabrication methods of metal fuel slugs have been studied in KAERI. U-10Zr-5Mn fuel slug containing volatile surrogate element Mn was soundly cast by modified injection casting under modest pressure. Evaporation of Mn during alternative casting could not be detected by chemical analysis. Mn element was most recovered with prevention of evaporation by alternative casting. Modified injection casting has been selected as an alternative fabrication method in KAERI, considering evaporation prevention, and proven benefits of high productivity, high yield, and good remote control

Alternative fossil-based transportation fuels

Science.gov (United States)

2008-01-01

"Alternative fuels derived from oil sands and from coal liquefaction can cost-effectively diversify fuel supplies, but neither type significantly reduces U.S. carbon-dioxide emissions enough to arrest long-term climate change".

Alternative fuels for vehicles; Alternative drivmidler

Energy Technology Data Exchange (ETDEWEB)

2012-02-15

Up until 2020 and onwards the analysis indicates that especially electricity, biogas and natural gas as propellants is economically attractive compared to conventional gasoline and diesel while other fuels have the same or higher costs for petrol and diesel. Especially biogas and electricity will also offer significant reductions in CO{sub 2} emissions, but also hydrogen, methanol, DME and to a lesser extent the second generation bioethanol and most of the other alternative fuels reduce CO{sub 2} emissions. Use of the traditional food-based first generation biofuels involves, at best, only modest climate benefits if land use changes are counted, and at worst, significant negative climate effects. Natural gas as a propellant involves a moderate climate gain, but may play a role for building infrastructure and market for gaseous fuels in large fleets, thereby contributing to the phasing in of biogas for transport. The electric-based automotive fuels are the most effective due to a high efficiency of the engine and an increasing proportion of wind energy in the electricity supply. The methanol track also has a relatively high efficiency. Among the others, the track based on diesel engines (biodiesel) is more effective than the track based on gasoline/Otto engines (gas and ethanol) as a result of the diesel engine's better efficiency. For the heavy vehicles all the selected alternative fuels to varying degrees reduce emissions of CO{sub 2}, particularly DME based on wood. The only exception to this is - as for passenger cars - the propellant synthetic diesel based on coal. (LN).

Alternative Fuels Data Center: Maine Transportation Data for Alternative

Science.gov (United States)

Biodiesel-Blended Diesel Documentation Requirement Data Download Fueling Stations 149 stations in Maine with alternative fuels Fuel Public Private Biodiesel (B20 and above) 2 1 Compressed Natural Gas (CNG) 0 2 Electric ://www.youtube.com/embed/jHftlruFR40 Video thumbnail for Maine's Only Biodiesel Manufacturer Powers Fleets in the

Discussion paper: direction for Canada's alternate fuels program

Energy Technology Data Exchange (ETDEWEB)

1982-09-01

There is a growing need to accelerate the consideration of alternate fuels for use in Canadian vehicle transportation. At the present time various governments and corporations are initiating alternate fuel programs involving ethanol, methanol, CNG, propane, etc. There is a bewildering array of perspectives as to which fuel or fuels will best serve Canada's needs in the future. In response to the 'Discussion Paper on Liquid Fuels Options, 1980', by the Federal Dept. of Energy, Mines and Resources, Ford of Canada has prepared this perspective on each of the alternate fuels from the company's vantage point as a vehicle manufacturer.

Alternative Fuels Data Center: Virginia Transportation Data for Alternative

Science.gov (United States)

/2018 Biodiesel and Green Diesel Definitions updated 4/9/2018 Data Download Fueling Stations 706 stations in Virginia with alternative fuels Fuel Public Private Biodiesel (B20 and above) 1 9 Compressed unit sold per GGE per unit sold per GGE Biodiesel (B20) $2.47/gallon $2.25/GGE $2.84/gallon $2.58/GGE

Lessons of the Past. Development of an alternative fuel infrastructure. The case of LPG/CNG in the Netherlands and other countries

International Nuclear Information System (INIS)

Backhaus, J.; Bunzeck, I.G.

2010-04-01

The introduction of an alternative transport fuel always bears a challenge that is often referred to as a 'chicken and egg' problem: while people will only become interested in and start switching to a new fuel if sufficient refuelling stations are available, industry will only start investing in the development of a refuelling infrastructure if the market is sufficiently developed and existing stations are economically viable. Governments have a variety of, for example, fiscal or regulatory measures at hand to facilitate and support the introduction of an alternative transport fuel. This report describes and analyses the introduction of liquefied petroleum gas (LPG) or compressed natural gas (CNG) in the Netherlands, Germany, Poland, Canada and Argentina. In particular, the report pays attention to the development of station coverage and vehicle numbers for these alternative fuels. Drivers and barriers to the introduction of LPG or CNG, such as fuel price developments, supporting policy instruments or a lack thereof were identified. Main focus are the Netherlands where LPG was introduced in the mid-1950s. A comparison of developments in the Netherlands with the other four countries reveals that well concerted efforts by policy makers and industry supporting a parallel development of vehicle uptake and refuelling station availability may lead to the firm establishment of an alternative fuel market. The report concludes with lessons learned for the introduction of hydrogen as an alternative transport fuel.

Proceedings of the 1993 Windsor Workshop on Alternative Fuels

Energy Technology Data Exchange (ETDEWEB)

1993-10-01

This report contains viewgraph papers on the following topics on alternative fuels: availability of alternative fueled engines and vehicles; emerging technologies; overcoming barriers to alternative fuels commercialization; infrastructure issues; and new initiatives in research and development.

The environment and the use of alternative fuels

International Nuclear Information System (INIS)

Okken, P.A.

1992-05-01

The contribution of the Netherlands Energy Research Foundation (ECN) to the ANWB symposium on alternative fuels and techniques concerns the necessity to use alternatives to reduce CO 2 emissions, the importance of system integration, and a discussion of the strong and weak points with regard to the introduction of the fuel alternatives in the Netherlands. First attention is paid to the greenhouse effect (CO 2 emissions) of the use of fuels. Options to reduce CO 2 emission from automobiles are mentioned. Than several alternative fuels and accompanying techniques, and their impact on the CO 2 emission, are discussed: diesel, liquid petroleum gas (LPG), compressed natural gas (CNG), methanol, ethanol, rapeseed, electricity, and hydrogen. The possibilities to reduce CO 2 emission in the Netherlands can be calculated by means of the Energy and Materials Scenarios (EMS). For several aspects assessments are given for the above-mentioned alternatives: availability of technology, ease of fuel storage, risk of use, impact on the city climate, full fuel cycle CO 2 emission, costs, and reserves. These aspects can be considered as valid for most of the industrialized countries. For the Netherlands two other aspects have been assessed: the interest of the oil industry in the introduction of alternative fuels, the availability of the alternatives in the Netherlands. 5 figs., 6 tabs., 10 refs

Alternatives for nuclear fuel disposal

International Nuclear Information System (INIS)

Ramirez S, J. R.; Badillo A, V.; Palacios H, J.; Celis del Angel, L.

2010-10-01

The spent fuel is one of the most important issues in the nuclear industry, currently spent fuel management is been cause of great amount of research, investments in the construction of repositories or constructing the necessary facilities to reprocess the fuel, and later to recycle the plutonium recovered in thermal reactors. What is the best solution? or, What is the best technology for a specific solution? Many countries have deferred the decision on selecting an option, while other works actively constructing repositories and others implementing the reprocessing facilities to recycle the plutonium obtained from nuclear spent fuel. In Mexico the nuclear power is limited to two reactors BWR type and medium size. So the nuclear spent fuel discharged has been accommodated at reactor's spent fuel pools. Originally these pools have enough capacity to accommodate spent fuel for the 40 years of designed plant operation. However, currently is under process an extended power up rate to 20% of their original power and also there are plans to extend operational life for 20 more years. Under these conditions there will not be enough room for spent fuel in the pools. So this work describes some different alternatives that have been studied in Mexico to define which will be the best alternative to follow. (Author)

Combustion of solid alternative fuels in the cement kiln burner

DEFF Research Database (Denmark)

Nørskov, Linda Kaare

In the cement industry there is an increasing environmental and financial motivation for substituting conventional fossil fuels with alternative fuels, being biomass or waste derived fuels. However, the introduction of alternative fuels may influence emissions, cement product quality, process...... stability, and process efficiency. Alternative fuel substitution in the calciner unit has reached close to 100% at many cement plants and to further increase the use of alternative fuels rotary kiln substitution must be enhanced. At present, limited systematic knowledge of the alternative fuel combustion...... properties and the influence on the flame formation is available. In this project a scientific approach to increase the fundamental understanding of alternative fuel conversion in the rotary kiln burner is employed through literature studies, experimental combustion characterisation studies, combustion...

Alternative Fuels DISI Engine Research ? Autoignition Metrics.

Energy Technology Data Exchange (ETDEWEB)

Sjoberg, Carl Magnus Goran [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Vuilleumier, David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-02-01

Improved engine efficiency is required to comply with future fuel economy standards. Alternative fuels have the potential to enable more efficient engines while addressing concerns about energy security. This project contributes to the science base needed by industry to develop highly efficient direct injection spark igniton (DISI) engines that also beneficially exploit the different properties of alternative fuels. Here, the emphasis is on quantifying autoignition behavior for a range of spark-ignited engine conditions, including directly injected boosted conditions. The efficiency of stoichiometrically operated spark ignition engines is often limited by fuel-oxidizer end-gas autoignition, which can result in engine knock. A fuel’s knock resistance is assessed empirically by the Research Octane Number (RON) and Motor Octane Number (MON) tests. By clarifying how these two tests relate to the autoignition behavior of conventional and alternative fuel formulations, fuel design guidelines for enhanced engine efficiency can be developed.

Near-term feasibility of alternative jet fuels

Science.gov (United States)

2009-01-01

This technical report documents the results of a joint study by the Massachusetts Institute of Technology (MIT) and the RAND Corporation on alternative fuels for commercial aviation. The study compared potential alternative jet fuels on the basis of ...

Alternative Fuel News, Vol. 3 No. 3

Energy Technology Data Exchange (ETDEWEB)

Clean Cities Program at DOE

1999-10-29

The alternative fuel industry is heating up. It is a very exciting time to be in the energy business, especially when it comes to transportation. Celebrating of the milestone 75th Clean Cities coalition and kick off of the new Federal Alternative Fuel Vehicle (AFV) USER Program is occurring in cities across the country. Clean Energy for the 21st Century and the events that are happening during Energy Awareness Month are covered in this issue. Spotlighted are niche markets; several airports across the country are successfully incorporating alternative fuels into their daily routines.

Alternative Fuel News, Vol. 3 No. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-23

This special issue of Alternative Fuel News highlights the Fifth National Clean Cities Conference held in Louisville, Kentucky. The momentum for the program is stronger than ever and the coalitions are working to propel the alternative fuel industry forward.

Testing and preformance measurement of straight vegetable oils as an alternative fuel for diesel engines

Science.gov (United States)

Lakshminarayanan, Arunachalam

Rising fuel prices, growing energy demand, concerns over domestic energy security and global warming from greenhouse gas emissions have triggered the global interest in bio-energy and bio-fuel crop development. Backlash from these concerns can result in supply shocks of traditional fossil fuels and create immense economic pressure. It is thus widely argued that bio-fuels would particularly benefit developing countries by off-setting their dependencies on imported petroleum. Domestically, the transportation sector accounts for almost 40% of liquid fuel consumption, while on-farm application like tractors and combines for agricultural purposes uses close to an additional 18%. It is estimated that 40% of the farm budget can be attributed to the fuel costs. With the cost of diesel continuously rising, farmers are now looking at using Straight Vegetable Oil (SVO) as an alternative fuel by producing their own fuel crops. This study evaluates conventional diesel compared to the use of SVO like Camelina, Canola and Juncea grown on local farms in Colorado for their performance and emissions on a John Deere 4045 Tier-II engine. Additionally, physical properties like density and viscosity, metal/mineral content, and cold flow properties like CFPP and CP of these oils were measured using ASTM standards and compared to diesel. It was found that SVOs did not show significant differences compared to diesel fuel with regards to engine emissions, but did show an increase in thermal efficiency. Therefore, this study supports the continued development of SVO production as a viable alternative to diesel fuels, particularly for on-farm applications. The need for providing and developing a sustainable, economic and environmental friendly fuel alternative has taken an aggressive push which will require a strong multidisciplinary education in the field of bio-energy. Commercial bio-energy development has the potential to not only alleviate the energy concerns, but also to give renewed

Alternative fuel cycles

International Nuclear Information System (INIS)

Penn, W.J.

1979-05-01

Uranium resource utilization and economic considerations provide incentives to study alternative fuel cycles as future options to the PHWR natural uranium cycle. Preliminary studies to define the most favourable alternatives and their possible introduction dates are discussed. The important and uncertain components which influence option selection are reviewed, including nuclear capacity growth, uranium availability and demand, economic potential, and required technological developments. Finally, a summary of Ontario Hydro's program to further assess cycle selection and define development needs is given. (auth)

Alternative Fuels Data Center: Seattle Bakery Delivers With Biodiesel

Science.gov (United States)

Trucks Seattle Bakery Delivers With Biodiesel Trucks to someone by E-mail Share Alternative Fuels Data Center: Seattle Bakery Delivers With Biodiesel Trucks on Facebook Tweet about Alternative Fuels Data Center: Seattle Bakery Delivers With Biodiesel Trucks on Twitter Bookmark Alternative Fuels

Addressing fuel recycling in solid oxide fuel cell systems fed by alternative fuels

DEFF Research Database (Denmark)

Rokni, Masoud

2017-01-01

An innovative study on anode recirculation in solid oxide fuel cell systems with alternative fuels is carried out and investigated. Alternative fuels under study are ammonia, pure hydrogen, methanol, ethanol, DME and biogas from biomass gasification. It is shown that the amount of anode off......%. Furthermore, it is founded that for the case with methanol, ethanol and DME then at high utilization factors, low anode recirculation is recommended while at low utilization factors, high anode recirculation is recommended. If the plant is fed by biogas from biomass gasification then for each utilization...

Proceedings of the 1996 Windsor workshop on alternative fuels

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-10-01

This document contains information which was presented at the 1996 Windsor Workshop on Alternative Fuels. Topics include: international links; industry topics and infrastructure issues; propane; engine developments; the cleanliness of alternative fuels; heavy duty alternative fuel engines; California zev commercialization efforts; and in-use experience.

Alternative energy review

International Nuclear Information System (INIS)

1991-09-01

A review is presented of electricity generation technologies which are considered to be alternatives to more conventional technologies. The review is limited to those technologies which have application in Ontario, and provides descriptions, technical and economic assessments, environmental information, and forecasts of potential use of solar energy, wind energy, fuel cells, biomass energy, peat, and municipal solid wastes. Of these technologies, only municipal solid waste combustion is economically viable under current conditions, but government policies prohibit the implementation of new facilities. Certain photovoltaic and wind energy technologies are being found viable for remote sites unconnected to the power grid. Wood waste combustion is viable in the forest products industry. The total potential contribution of these six alternative technologies to Ontario's energy production is forecast at under 190 MW to a range of 685-1,465 MW by the year 2005, according to three different scenarios. The technologies showing the greatest future promise are fuel cells, photovoltaics, and biomass. Except for municipal waste combustion, cost continues to be a significant barrier to utility-scale application of alternative generation technologies in Ontario. However, private individuals and corporations (non-utility generators) may adopt some of these technologies in the absence of access to the power grid, in cogeneration applications, or for demonstration purposes. 120 refs., 79 figs., 93 tabs

Compatibility of elastomers in alternate jet fuels

Science.gov (United States)

Kalfayan, S. H.; Fedors, R. F.; Reilly, W. W.

1979-01-01

The compatibility of elastomeric compositions of known resistance to aircraft fuels was tested for potential use in Jet A type fuels obtainable from alternate sources, such as coal. Since such fuels were not available at the time, synthetic alternate fuels were prepared by adding tetralin to a petroleum based Jet A type fuel to simulate coal derived fuels which are expected to contain higher amounts of aromatic and hydroaromatic hydrocarbons. The elastomeric compounds tested were based on butadiene-acrylonitrile rubber, a castable Thiokol polysulfide rubber, and a castable fluorosilicone rubber. Batches of various cross-link densities of these rubbers were made and their chemical stress relaxation behavior in fuel, air, and nitrogen, their swelling properties, and response to mechanical testing were determined.

Alternative Fuel News, Vol. 2, No. 4

Energy Technology Data Exchange (ETDEWEB)

O' Connor, K.; Riley, C.; Raye, M.

1998-11-30

This issue of Alternative Fuel News highlights the accomplishments of the Clean Cities coalitions during the past 5 years. Now Clean Cities advocates in city after city across the US are building stations and driving alternative fuel vehicles, in addition to enhancing public awareness.

Alternative Fuel News: Official Publication of the Clean Cities Network and the Alternative Fuels Data Center, Vol. 5, No. 3

Energy Technology Data Exchange (ETDEWEB)

2001-11-01

A quarterly magazine with articles on alternative fuel school buses, the market growth of biodiesel fuel, National AFV Day 2002, model year 2002 alternative fuel passenger cars and light trucks, the Michelin Challenge Bibendum road rally, and advanced technology vehicles at Robins Air Force Base, the Top Ten Clean Cities coalitions for 2000, and AFVs on college campuses.

Alternate fuels; Combustibles alternos

Energy Technology Data Exchange (ETDEWEB)

Romero Paredes R, Hernando; Ambriz G, Juan Jose [Universidad Autonoma Metropolitana. Iztapalapa (Mexico)

2003-07-01

In the definition and description of alternate fuels we must center ourselves in those technological alternatives that allow to obtain compounds that differ from the traditional ones, in their forms to be obtained. In this article it is tried to give an overview of alternate fuels to the conventional derivatives of petroleum and that allow to have a clear idea on the tendencies of modern investigation and the technological developments that can be implemented in the short term. It is not pretended to include all the tendencies and developments of the present world, but those that can hit in a relatively short term, in accordance with agreed with the average life of conventional fuels. Nevertheless, most of the conversion principles are applicable to the spectrum of carbonaceous or cellulosic materials which are in nature, are cultivated or wastes of organic origin. Thus one will approach them in a successive way, the physical, chemical and biological conversions that can take place in a production process of an alternate fuel or the same direct use of the fuel such as burning the sweepings derived from the forests. [Spanish] En la definicion y descripcion de combustibles alternos nos debemos centrar en aquellas alternativas tecnologicas que permitan obtener compuestos que difieren de los tradicionales, al menos en sus formas de ser obtenidos. En este articulo se pretende dar un panorama de los combustibles alternos a los convencionales derivados del petroleo y que permita tener una idea clara sobre las tendencias de la investigacion moderna y los desarrollos tecnologicos que puedan ser implementados en el corto plazo. No se pretende abarcar todas las tendencias y desarrollos del mundo actual, sino aquellas que pueden impactar en un plazo relativamente corto, acordes con la vida media de los combustibles convencionales. Sin embargo, la mayor parte de los principios de conversion son aplicables al espectro de materiales carbonaceos o celulosicos los cuales se

Outlook on Standardization of Alternative Vehicle Fuels

Energy Technology Data Exchange (ETDEWEB)

Rehnlund, B [Atrax Energi AB (Sweden)

2008-10-15

The use of fossil but in first hand biobased alternative fuels in transportation has increased over the last decades. This change is primarily driven by concerns about climate change that is caused by emissions of fossil carbon dioxide and other greenhouse gases, but also by the impact on health and environment, caused by emissions of regulated as well as non-regulated emissions from the transport sector. Most alternative fuels will help to reduce the emissions of regulated and non-regulated emissions, while alternative fuels based on biomass also will contribute to reduced net emissions of carbon dioxide. Since the mid 1990s, the use of biomass based fuels such as ethanol and biodiesel has reached levels high enough in for example Europe, Brazil and the U.S. to motivate national or regional specifications/standards. Especially from the vehicle/engine manufacturer's point of view standards are of high importance. From early 2000 onwards, the international trade of biofuels (for example from Brazil to the U.S. and Europe) has grown, and this has created a need for common international specifications/standards. This report presents information about national and regional standards for alternative fuels, but also, when existing and reported, standards on a global level are described and discussed. Ongoing work concerning new or revised standards on alternative fuels on national, regional or global level is also discussed. In this report we have covered standards on all kind of alternative fuels, exemplified below. However, the focus is on liquid biofuels for diesel engines and Otto engines. 1) Liquid fuels for diesel engines (compression ignition engines), such as Fatty Acid Methyl Esters (FAME), Fatty Acid Ethyl Esters (FAEE), alcohols, alcohol derivates and synthetic diesel fuels. 2) Liquid fuels for Otto engines (spark ignition engines), such as alcohols, ethers and synthetic gasoline. 3) Liquefied fossil petroleum gas (LPG). 4) Di-Methyl Ether (DME). 5) Fossil

Outlook on Standardization of Alternative Vehicle Fuels

Energy Technology Data Exchange (ETDEWEB)

Rehnlund, B. [Atrax Energi AB (Sweden)

2008-10-15

The use of fossil but in first hand biobased alternative fuels in transportation has increased over the last decades. This change is primarily driven by concerns about climate change that is caused by emissions of fossil carbon dioxide and other greenhouse gases, but also by the impact on health and environment, caused by emissions of regulated as well as non-regulated emissions from the transport sector. Most alternative fuels will help to reduce the emissions of regulated and non-regulated emissions, while alternative fuels based on biomass also will contribute to reduced net emissions of carbon dioxide. Since the mid 1990s, the use of biomass based fuels such as ethanol and biodiesel has reached levels high enough in for example Europe, Brazil and the U.S. to motivate national or regional specifications/standards. Especially from the vehicle/engine manufacturer's point of view standards are of high importance. From early 2000 onwards, the international trade of biofuels (for example from Brazil to the U.S. and Europe) has grown, and this has created a need for common international specifications/standards. This report presents information about national and regional standards for alternative fuels, but also, when existing and reported, standards on a global level are described and discussed. Ongoing work concerning new or revised standards on alternative fuels on national, regional or global level is also discussed. In this report we have covered standards on all kind of alternative fuels, exemplified below. However, the focus is on liquid biofuels for diesel engines and Otto engines. 1) Liquid fuels for diesel engines (compression ignition engines), such as Fatty Acid Methyl Esters (FAME), Fatty Acid Ethyl Esters (FAEE), alcohols, alcohol derivates and synthetic diesel fuels. 2) Liquid fuels for Otto engines (spark ignition engines), such as alcohols, ethers and synthetic gasoline. 3) Liquefied fossil petroleum gas (LPG). 4) Di-Methyl Ether (DME). 5

Alternative motor fuels today and tomorrow

International Nuclear Information System (INIS)

Bensaid, B.

2004-01-01

Today, petroleum products account for 97% of the energy consumed in road transport. The purpose of replacing these products with alternative energies is to reduce oil dependence as well as greenhouse gas emissions. The high price of oil has promoted the use of 'conventional' alternative motor fuels (biofuels, LPG, NGV) and also renewed interest in syn-fuels (GTL, CTL, BTL) that have already given rise to industrial and pilot projects. (author)

10 CFR 503.21 - Lack of alternate fuel supply.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Lack of alternate fuel supply. 503.21 Section 503.21 Energy DEPARTMENT OF ENERGY (CONTINUED) ALTERNATE FUELS NEW FACILITIES Temporary Exemptions for New Facilities § 503.21 Lack of alternate fuel supply. (a) Eligibility. Section 211(a)(1) of the Act provides for...

Pulse Detonation Assessment for Alternative Fuels

Directory of Open Access Journals (Sweden)

Muhammad Hanafi Azami

2017-03-01

Full Text Available The higher thermodynamic efficiency inherent in a detonation combustion based engine has already led to considerable interest in the development of wave rotor, pulse detonation, and rotating detonation engine configurations as alternative technologies offering improved performance for the next generation of aerospace propulsion systems, but it is now important to consider their emissions also. To assess both performance and emissions, this paper focuses on the feasibility of using alternative fuels in detonation combustion. Thus, the standard aviation fuels Jet-A, Acetylene, Jatropha Bio-synthetic Paraffinic Kerosene, Camelina Bio-synthetic Paraffinic Kerosene, Algal Biofuel, and Microalgae Biofuel are all asessed under detonation combustion conditions. An analytical model accounting for the Rankine-Hugoniot Equation, Rayleigh Line Equation, and Zel’dovich–von Neumann–Doering model, and taking into account single step chemistry and thermophysical properties for a stoichiometric mixture, is applied to a simple detonation tube test case configuration. The computed pressure rise and detonation velocity are shown to be in good agreement with published literature. Additional computations examine the effects of initial pressure, temperature, and mass flux on the physical properties of the flow. The results indicate that alternative fuels require higher initial mass flux and temperature to detonate. The benefits of alternative fuels appear significant.

Hawaii alternative fuels utilization program. Phase 3, final report

Energy Technology Data Exchange (ETDEWEB)

Kinoshita, C.M.; Staackmann, M.

1996-08-01

The Hawaii Alternative Fuels Utilization Program originated as a five-year grant awarded by the US Department of Energy (USDOE) to the Hawaii Natural Energy Institute (HNEI) of the University of Hawaii at Manoa. The overall program included research and demonstration efforts aimed at encouraging and sustaining the use of alternative (i.e., substitutes for gasoline and diesel) ground transportation fuels in Hawaii. Originally, research aimed at overcoming technical impediments to the widespread adoption of alternative fuels was an important facet of this program. Demonstration activities centered on the use of methanol-based fuels in alternative fuel vehicles (AFVs). In the present phase, operations were expanded to include flexible fuel vehicles (FFVs) which can operate on M85 or regular unleaded gasoline or any combination of these two fuels. Additional demonstration work was accomplished in attempting to involve other elements of Hawaii in the promotion and use of alcohol fuels for ground transportation in Hawaii.

Alternative Fuels Data Center: How Do Fuel Cell Electric Vehicles Work

Science.gov (United States)

vehicles. Hydrogen car image Key Components of a Hydrogen Fuel Cell Electric Car Battery (auxiliary): In an Using Hydrogen? Fuel Cell Electric Vehicles Work Using Hydrogen? to someone by E-mail Share Alternative Fuels Data Center: How Do Fuel Cell Electric Vehicles Work Using Hydrogen? on Facebook Tweet about

Outlook for alternative energy sources. [aviation fuels

Science.gov (United States)

Card, M. E.

1980-01-01

Predictions are made concerning the development of alternative energy sources in the light of the present national energy situation. Particular emphasis is given to the impact of alternative fuels development on aviation fuels. The future outlook for aircraft fuels is that for the near term, there possibly will be no major fuel changes, but minor specification changes may be possible if supplies decrease. In the midterm, a broad cut fuel may be used if current development efforts are successful. As synfuel production levels increase beyond the 1990's there may be some mixtures of petroleum-based and synfuel products with the possibility of some shale distillate and indirect coal liquefaction products near the year 2000.

Alternative Fuels Data Center: Colorado Airport Relies on Natural Gas

Science.gov (United States)

Fueling Stations Colorado Airport Relies on Natural Gas Fueling Stations to someone by E-mail Share Alternative Fuels Data Center: Colorado Airport Relies on Natural Gas Fueling Stations on Facebook Tweet about Alternative Fuels Data Center: Colorado Airport Relies on Natural Gas Fueling Stations on

Alternative fuels, fuel cycles, and reactors: are they useful. are they necessary

International Nuclear Information System (INIS)

Spinrad, B.I.

1985-01-01

This chapter discusses reactors, fuel cycles, and fuel production concepts other than those considered conventional in the nuclear community. An attempt is made to look for improvements with the aim of providing cheaper and more durable energy systems, and to contribute toward a solution of the threat of weapons material diversion and weapons proliferation problems. Topics considered include breeding, alternate breeder cycles, alternative reprocessing schemes, symbiotic reactor systems, an interim strategy, and other sources of nuclear fuel. It is determined that the reprocessing of spent fuel is an important safeguard measure in itself

Alternative Fuels Data Center: Missouri Transportation Data for Alternative

Science.gov (United States)

stations in Missouri with alternative fuels Fuel Public Private Biodiesel (B20 and above) 1 2 Compressed Students Get Hands-On Training With Biodiesel Missouri High School Students Get Hands-On Training With Biodiesel Feb. 5, 2016 https://youtube.com/embed/p4pVRgoWyZw Video thumbnail for AT&T Fleet Reaches

Alternative Fuels and Chemicals from Synthesis Gas

Energy Technology Data Exchange (ETDEWEB)

None, None

1998-12-02

The overall objectives of this program are to investigate potential technologies for the conversion of synthesis gas to oxygenated and hydrocarbon fuels and industrial chemicals, and to demonstrate the most promising technologies at DOE's LaPorte, Texas, Slurry Phase Alternative Fuels Development Unit (AFDU). The program will involve a continuation of the work performed under the Alternative Fuels from Coal-Derived Synthesis Gas Program and will draw upon information and technologies generated in parallel current and future DOE-funded contracts.

Alternative fuels and chemicals from synthesis gas

Energy Technology Data Exchange (ETDEWEB)

Unknown

1998-08-01

The overall objectives of this program are to investigate potential technologies for the conversion of synthesis gas to oxygenated and hydrocarbon fuels and industrial chemicals, and to demonstrate the most promising technologies at DOE's LaPorte, Texas, Slurry Phase Alternative Fuels Development Unit (AFDU). The program will involve a continuation of the work performed under the Alternative Fuels from Coal-Derived Synthesis Gas Program and will draw upon information and technologies generated in parallel current and future DOE-funded contracts.

ALTERNATIVE FUELS AND CHEMICALS FROM SYNTHESIS GAS

Energy Technology Data Exchange (ETDEWEB)

Unknown

1999-01-01

The overall objectives of this program are to investigate potential technologies for the conversion of synthesis gas to oxygenated and hydrocarbon fuels and industrial chemicals, and to demonstrate the most promising technologies at DOE's LaPorte, Texas, Slurry Phase Alternative Fuels Development Unit (AFDU). The program will involve a continuation of the work performed under the Alternative Fuels from Coal-Derived Synthesis Gas Program and will draw upon information and technologies generated in parallel current and future DOE-funded contracts.

Alternative Fuels and Chemicals From Synthesis Gas

Energy Technology Data Exchange (ETDEWEB)

none

1998-07-01

The overall objectives of this program are to investigate potential technologies for the conversion of synthesis gas to oxygenated and hydrocarbon fuels and industrial chemicals, and to demonstrate the most promising technologies at DOE's LaPorte, Texas, Slurry Phase Alternative Fuels Development Unit (AFDU). The program will involve a continuation of the work performed under the Alternative Fuels from Coal-Derived Synthesis Gas Program and will draw upon information and technologies generated in parallel current and future DOE-funded contracts.

Breaking down the barriers to commercialization of fuel cells in transportation through Government - industry R&D programs

Energy Technology Data Exchange (ETDEWEB)

Chalk, S.G. [Dept. of Energy, Washington, DC (United States); Venkateswaran, S.R. [Energetics, Inc., Columbia, MD (United States)

1996-12-31

PEM fuel cell technology is rapidly emerging as a viable propulsion alternative to the internal combustion engine. Fuel cells offer the advantages of low emissions, high efficiency, fuel flexibility, quiet and continuous operation, and modularity. Over the last decade, dramatic advances have been achieved in the performance and cost of PEM fuel cell technologies for automotive applications. However, significant technical barriers remain to making fuel cell propulsion systems viable alternatives to the internal combustion engine. This paper focuses on the progress achieved and remaining technical barriers while highlighting Government-industry R&D efforts that are accelerating fuel cell technology toward commercialization.

Second interim report of the Interagency Commission on Alternative Motor Fuels

International Nuclear Information System (INIS)

1991-09-01

This report describes progress the commission and government agencies have made in implementing the provisions of the Alternative Motor Fuels Act of 1988, assessing the role of alternative motor fuels in the US transportation sector, and developing policies to promote the use of alternative fuels. The alternative motor-fuels policies proposed in the National Energy Strategy (NES) are described and shows how they compose an effective long-term plan to encourage the widespread use of alternative motor fuels. The progress to date of the Department of Energy (DOE) and other agencies in implementing the programs required by the AMFA is reported. A detailed scenario of future alternative-fuel use that displaces 2.5 million barrels per day (MMBD) of petroleum and a feasible path of vehicle production and fuel supply leading to that goal is described. An analytical tool for exploring and quantifying the energy market impacts of alternative fuels, the Alternative Fuels Trade Model (AFTM), is described. The AFTM provides a means of investigating the impacts of alternative fuels in interrelated world energy markets for petroleum and natural gas. Several major initiatives have recently been enacted that have important ramifications for alternative-fuels policy. The Clean Air Act Amendments of 1990 contain provisions mandating the use of nonpetroleum oxygenates in reformulated gasoline. Other provisions for much more stringent emissions standards may affect the ability of manufacturers to make and sell conventional-fuel vehicles or, at the very least, affect their cost-effectiveness in comparison to cleaner alternative-fuel vehicles (AFV's). Finally, the key areas in which technological advances could substantially improve the competitiveness of AFV technologies in the marketplace are reviewed

Alternative Fuels Data Center: Vermont Transportation Data for Alternative

Science.gov (United States)

alternative fuels Fuel Public Private Biodiesel (B20 and above) 3 0 Compressed Natural Gas (CNG) 1 2 Electric Recycled Cooking Oil Powers Biodiesel Vehicles in Vermont Recycled Cooking Oil Powers Biodiesel Vehicles in sold per GGE Biodiesel (B20) $2.79/gallon $2.54/GGE $2.84/gallon $2.58/GGE Biodiesel (B99-B100) $2.47

75 FR 26165 - Regulation of Fuels and Fuel Additives: Alternative Affirmative Defense Requirements for Ultra...

Science.gov (United States)

2010-05-11

... Regulation of Fuels and Fuel Additives: Alternative Affirmative Defense Requirements for Ultra-Low Sulfur... refiners, importers, distributors, and retailers of highway diesel fuel the option to use an alternative affirmative defense if the Agency finds highway diesel fuel samples above the specified sulfur standard at...

A COMPREHENSIVE STUDY OF DI DIESEL ENGINE PERFORMANCE WITHVEGETABLE OIL: AN ALTERNATIVE BIO-FUEL SOURCE OF ENERGY

Directory of Open Access Journals (Sweden)

A. K. Azad

2012-06-01

Full Text Available This study offers comprehensive details on the use of bio-fuel as a viable and alternative source of energy. The bio-fuel was prepared from vegetable oil, i.e., mustard oil and tested in a diesel engine in both pure form and as a diesel blend. The mustard oil blend proportions were 20%, 30%, 40% and 50% and named as bio-diesel blends B20, B30, B40 and B50. A fuel-testing laboratory determined the properties of the pure mustard oil fuel and its blends, i.e., density, viscosity, dynamic viscosity, carbon residue, flash point, fire point and calorific value. An assessment of engine performance, i.e., brake horsepower (bhp, brake specific fuel consumption (bsfc, brake thermal efficiency (bte and brake mean effective pressure (bmep etc., was carried out for pure diesel, pure mustard and the blends, both in laboratory conditions and under British Standard (BS conditions. Finally, an analysis and comparison was made of the effects of the various fuels on the different engine properties.

Alternative Fuels Data Center: Alabama City Leads With Biodiesel and

Science.gov (United States)

Ethanol Alabama City Leads With Biodiesel and Ethanol to someone by E-mail Share Alternative Fuels Data Center: Alabama City Leads With Biodiesel and Ethanol on Facebook Tweet about Alternative Fuels Data Center: Alabama City Leads With Biodiesel and Ethanol on Twitter Bookmark Alternative Fuels

Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas

Science.gov (United States)

Tree Biodiesel Truck Transports Capitol Christmas Tree to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas Tree on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas Tree on Twitter Bookmark Alternative

Preliminary ecotoxicity assessment of new generation alternative fuels in seawater.

Science.gov (United States)

Rosen, Gunther; Dolecal, Renee E; Colvin, Marienne A; George, Robert D

2014-06-01

The United States Navy (USN) is currently demonstrating the viability of environmentally sustainable alternative fuels to power its fleet comprised of aircraft and ships. As with any fuel used in a maritime setting, there is potential for introduction into the environment through transport, storage, and spills. However, while alternative fuels are often presumed to be eco-friendly relative to conventional petroleum-based fuels, their environmental fate and effects on marine environments are essentially unknown. Here, standard laboratory-based toxicity experiments were conducted for two alternative fuels, jet fuel derived from Camelina sativa (wild flax) seeds (HRJ5) and diesel fuel derived from algae (HRD76), and two conventional counterparts, jet fuel (JP5) and ship diesel (F76). Initial toxicity tests performed on water-accommodated fractions (WAF) from neat fuels partitioned into seawater, using four standard marine species in acute and chronic/sublethal tests, indicate that the alternative fuels are significantly less toxic to marine organisms. Published by Elsevier Ltd.

75 FR 29605 - Clean Alternative Fuel Vehicle and Engine Conversions

Science.gov (United States)

2010-05-26

... Part II Environmental Protection Agency 40 CFR Parts 85 and 86 Clean Alternative Fuel Vehicle and...-0299; FRL-9149-9] RIN 2060-AP64 Clean Alternative Fuel Vehicle and Engine Conversions AGENCY... streamline the process by which manufacturers of clean alternative fuel conversion systems may demonstrate...

Multi-criteria analysis of alternative-fuel buses for public transportation

International Nuclear Information System (INIS)

Tzeng, G.-H.; Lin, C.-W.; Opricovic, Serafim

2005-01-01

The technological development of buses with new alternative fuels is considered in this paper. Several types of fuels are considered as alternative-fuel modes, i.e., electricity, fuel cell (hydrogen), and methanol. Electric vehicles may be considered the alternative-fuel vehicles with the lowest air pollution. Hybrid electric vehicles provide an alternate mode, at least for the period of improving the technology of electric vehicles. A hybrid electric vehicle is defined as a vehicle with the conventional internal combustion engine and an electric motor as its major sources of power. Experts from different decision-making groups performed the multiple attribute evaluation of alternative vehicles. AHP is applied to determine the relative weights of evaluation criteria. TOPSIS and VIKOR are compared and applied to determine the best compromise alternative fuel mode. The result shows that the hybrid electric bus is the most suitable substitute bus for Taiwan urban areas in the short and median term. But, if the cruising distance of the electric bus extends to an acceptable range, the pure electric bus could be the best alternative

Alternative Fuels Data Center: Signage for Plug-In Electric Vehicle

Science.gov (United States)

Send a link to Alternative Fuels Data Center: Signage for Plug-In Electric Vehicle Charging Stations to someone by E-mail Share Alternative Fuels Data Center: Signage for Plug-In Electric Vehicle Charging Stations on Facebook Tweet about Alternative Fuels Data Center: Signage for Plug-In Electric Vehicle

Alternative Fuels Data Center: Phoenix Cleans Up with Natural Gas

Science.gov (United States)

Phoenix Cleans Up with Natural Gas to someone by E-mail Share Alternative Fuels Data Center : Phoenix Cleans Up with Natural Gas on Facebook Tweet about Alternative Fuels Data Center: Phoenix Cleans Up with Natural Gas on Twitter Bookmark Alternative Fuels Data Center: Phoenix Cleans Up with Natural

77 FR 36423 - Labeling Requirements for Alternative Fuels and Alternative Fueled Vehicles

Science.gov (United States)

2012-06-19

... delivered to the following address: Federal Trade Commission, Office of the Secretary, Room H-113 (Annex N... cell, advanced lean burn, and hybrid motor vehicles) that were added to the definition of ``alternative... legislation (i.e., lean burn, hybrid, and fuel cell vehicles). No comments opposed this approach. Edison...

Comparison of alternate fuels for aircraft

Science.gov (United States)

Witcofski, R. D.

1979-01-01

A comparison of candidate alternate fuels for aircraft is presented. The fuels discussed include liquid hydrogen, liquid methane, and synthetic aviation kerosene. Each fuel is evaluated from the standpoint of production, transmission, airport storage and distribution facilities, and use in aircraft. Technology deficient areas for cryogenic fuels, which should be advanced prior to the introduction of the fuels into the aviation industry, are identified, as are the cost and energy penalties associated with not achieving those advances. Environmental emissions and safety aspects of fuel selection are discussed. A detailed description of the various fuel production and liquefaction processes and their efficiencies and economics is given.

FEED SYSTEM INNOVATION FOR GASIFICATION OF LOCALLY ECONOMICAL ALTERNATIVE FUELS (FIGLEAF)

Energy Technology Data Exchange (ETDEWEB)

Michael L. Swanson; Mark A. Musich; Darren D. Schmidt; Joseph K. Schultz

2003-02-01

the ability of the gasifier to operate with alternative feedstocks at up to 80% moisture, a decision was made to investigate a pumping system for delivering the as-received fuel across the pressure boundary into the second stage of the gasifier. A high-pressure feed pump and fuel dispersion nozzles were tested for their ability to cross the pressure boundary and adequately disperse the sludge into the second stage of the gasifier. These results suggest that it is technically feasible to get the sludge dispersed to an appropriate size into the second stage of the gasifier although the recycle syngas pressure needed to disperse the sludge would be higher than originally desired. A preliminary design was prepared for a sludge-receiving, storage, and high-pressure feeding system at the Wabash River Plant. The installed capital costs were estimated at approximately $9.7 million, within an accuracy of {+-}10%. An economic analysis using DOE's IGCC Model, Version 3 spreadsheet indicates that in order to justify the additional capital cost of the system, Global Energy would have to receive a tipping fee of $12.40 per wet ton of municipal sludge delivered. This is based on operation with petroleum coke as the primary fuel. Similarly, with coal as the primary fuel, a minimum tipping of $16.70 would be required. The availability of delivered sludge from Indianapolis, Indiana, in this tipping-fee range is unlikely; however, given the higher treatment costs associated with sludge treatment in Chicago, Illinois, delivery of sludge from Chicago, given adequate rail access, might be economically viable.

Emission Control Cost-Effectiveness of Alternative-Fuel Vehicles

OpenAIRE

Wang, Quanlu; Sperling, Daniel; Olmstead, Janis

1993-01-01

Although various legislation and regulations have been adopted to promote the use of alternative-fuel vehicles for curbing urban air pollution problems, there is a lack of systematic comparisons of emission control cost-effectiveness among various alternative-fuel vehicle types. In this paper, life-cycle emission reductions and life-cycle costs were estimated for passenger cars fueled with methanol, ethanol, liquified petroleum gas, compressed natural gas, and electricity. Vehicle emission es...

Alternative Fuel News, Vol. 2, No. 5

Energy Technology Data Exchange (ETDEWEB)

NREL

1999-01-06

In this issue of the Alternative Fuel News, the authors remember what happened just 25 years ago (the energy crisis of 1973) and reiterate that foreign oil dependence is still a national issue. Highlighted are some the successes in the Clean Cities Program and the alternative fuels industry. Also featured is the Natural Gas Vehicle Coalition (NGVC) and the United States Postal Service (USPS) delivers with AFVs.

Modern approach to the problem of fossil gas fuels replacement by alternative fuels

Energy Technology Data Exchange (ETDEWEB)

Soroka, Boris [Gas Institute, National Academy of Sciences, Kiev (Ukraine)

2013-07-01

New scientific and engineering fundamentals of fuels substitution have been developed instead of obsolete methodology “Interchangeability of Fuel Gases” developed in USA and existing from the middle of XX{sup th} century. To perform the complex prediction of total or partial substitution of given flow rate of natural gas NG for alternative gases AG the following parameters are to be predicted: plant utilization efficiencies – regarding fuel and energy utilization, the last in form of heat Ș{sub H} and exergy Ș{sub eff} efficiencies, saving or overexpenditure of the NG flow rate in the gas mixture with AG, specific fuel consumption b f and specific issue of harmful substances C{sub t} – pollutants in the combustion products (C{sub NO{sub x}} ) and greenhouse gases (C {sub CO{sub 2}} ). Certification of alternative gas fuels and fuel mixtures as a commodity products is carried out in frame of our approach with necessary set of characteristics, similar to those accepted in the world practice. Key words: alternative fuel, fuel replacement (substitution), natural gas, process gases, theoretical combustion temperature, thermodynamic equilibrium computations, total enthalpy.

Alternative fuel news: Official publication of the clean cities network and the alternative fuels data center, Vol. 4, No. 1

Energy Technology Data Exchange (ETDEWEB)

NREL

2000-03-27

This issue of Alternative Fuel News contains information on the upcoming Clean Cities Conference to be held May 7--10, 2000 in San Diego, California. Highlighted in this issue is the success of the Clean Cities Program in creating clean corridors that permit fleets that serve multiple cities to purchase AFVs with confidence, knowing that fueling convenience and supply will not be a problem. Also look for articles on electric vehicles, transit buses; state and fuel provider enforcement; the Salt Lake and Greater Long Island Clean Cities coalitions, HEVs and fuel cells are a big hit at auto shows; DOE awards alternative fuel grants to 33 National Parks; and the Energy Policy Act (EPAct) Section 506 report.

Distillate Fuel Trends: International Supply Variations and Alternate Fuel Properties

Science.gov (United States)

2013-01-31

fuel in NATO countries will have some amount of FAME present. There is some work being done on hydrocarbon alternatives but the regulatory structure ... synthesis or hydrotreatment – Requirements and test methods.” According to the specification, paraffinic diesel fuel does not meet the current requirements...or international specification for triglyceride based fuel oils (straight vegetable oil / raw vegetable oil). The same holds true for alcohol-based

An evaluation of the alternative transport fuel policies for Turkey

International Nuclear Information System (INIS)

Arslan, Ridvan; Ulusoy, Yahya; Tekin, Yuecel; Suermen, Ali

2010-01-01

The search for alternative fuels and new fuel resources is a top priority for Turkey, as is the case in the majority of countries throughout the world. The fuel policies pursued by governmental or civil authorities are of key importance in the success of alternative fuel use, especially for widespread and efficient use. Following the 1973 petroleum crisis, many users in Turkey, especially in transportation sector, searched for alternative fuels and forms of transportation. Gasoline engines were replaced with diesel engines between the mid-1970s and mid-1980s. In addition, natural gas was introduced to the Turkish market for heating in the early 1990s. Liquid petroleum gas was put into use in the mid-1990s, and bio-diesel was introduced into the market for transportation in 2003. However, after long periods of indifference governmental action, guidance and fuel policies were so weak that they did not make sense. Entrepreneurs and users experienced great economical losses and lost confidence in future attempts to search for other possible alternatives. In the present study, we will look at the history of alternative fuel use in the recent past and investigate the alternative engine fuel potential of Turkey, as well as introduce possible future policies based on experience.

Ontario Select Committee on Alternative Fuel Sources : Final Report

International Nuclear Information System (INIS)

Galt, D.

2002-06-01

On June 28, 2001, the Ontario Legislative Assembly appointed the Select Committee an Alternative Fuel Sources, comprised of representatives of all parties, with a broad mandate to investigate, report and offer recommendations with regard to the various options to support the development and application of environmentally sustainable alternatives to the fossil fuel sources already existing. The members of the Committee elected to conduct extensive public hearings, conduct site visits, attend relevant conferences, do some background research to examine a vast number of alternative fuel and energy sources that could be of relevance to the province of Ontario. A discussion paper (interim report) was issued by the Committee in November 2001, and the present document represents the final report, containing 141 recommendations touching 20 topics. The information contained in the report is expected to assist in the development and outline of policy and programs designed to specifically support alternative fuels and energy sources and applicable technologies. Policy issues were discussed in Part A of the report, along with the appropriate recommendations. The recommendations on specific alternative fuels and energy sources were included in Part B of the report. It is believed that the dependence of Ontario on traditional petroleum-based fuels and energy sources can be reduced through aggressive action on alternative fuels and energy. The benefits of such action would be felt in the area of air quality, with social, and economic benefits as well. 3 tabs

Methanol supply issues for alternative fuels demonstration programs

International Nuclear Information System (INIS)

Teague, J.M.; Koyama, K.K.

1995-01-01

This paper surveys issues affecting the supply of fuel-grade methanol for the California Energy Commission's alternative fuels demonstration programs and operations by other public agencies such as transit and school districts. Establishing stable and reasonably priced sources of methanol (in particular) and of alternative fuels generally is essential to their demonstration and commercialization. Development both of vehicle technologies and of fuel supply and distribution are complementary and must proceed in parallel. However, the sequence of scaling up supply and distribution is not necessarily smooth; achievement of volume thresholds in demand and through-put of alternative fuels are marked by different kinds of challenges. Four basic conditions should be met in establishing a fuel supply: (1) it must be price competitive with petroleum-based fuels, at least when accounting for environmental and performance benefits; (2) bulk supply must meet volumes required at each phase; necessitating resilience among suppliers and a means of designating priority for high value users; (3) distribution systems must be reliable, comporting with end users' operational schedules; (4) volatility in prices to the end user for the fuel must be minimal. Current and projected fuel volumes appear to be insufficient to induce necessary economies of scale in production and distribution for fuel use. Despite their benefits, existing programs will suffer absent measures to secure economical fuel supplies. One solution is to develop sources that are dedicated to fuel markets and located within the end-use region

Simulating the Use of Alternative Fuels in a Turbofan Engine

Science.gov (United States)

Litt, Jonathan S.; Chin, Jeffrey Chevoor; Liu, Yuan

2013-01-01

The interest in alternative fuels for aviation has created a need to evaluate their effect on engine performance. The use of dynamic turbofan engine simulations enables the comparative modeling of the performance of these fuels on a realistic test bed in terms of dynamic response and control compared to traditional fuels. The analysis of overall engine performance and response characteristics can lead to a determination of the practicality of using specific alternative fuels in commercial aircraft. This paper describes a procedure to model the use of alternative fuels in a large commercial turbofan engine, and quantifies their effects on engine and vehicle performance. In addition, the modeling effort notionally demonstrates that engine performance may be maintained by modifying engine control system software parameters to account for the alternative fuel.

Alternative Aviation Fuels: Overview of Challenges, Opportunities, and Next Steps

Energy Technology Data Exchange (ETDEWEB)

None, None

2017-03-28

The Alternative Aviation Fuels: Overview of Challenges, Opportunities, and Next Steps report, published by the U.S. Department of Energy’s Bioenergy Technologies Office (BETO) provides an overview of the current state of alternative aviation fuels, based upon findings from recent peer-reviewed studies, scientific working groups, and BETO stakeholder input provided during the Alternative Aviation Fuel Workshop.

Mitigating environmental pollution and impacts from fossil fuels: The role of alternative fuels

Energy Technology Data Exchange (ETDEWEB)

Liu, L.; Cheng, S.Y.; Li, J.B.; Huang, Y.F. [Dalhousie University, Halifax, NS (Canada)

2007-07-01

In order to meet the rising global demand for energy, rapid development of conventional fossil fuels (i.e., coal, oil, and natural gas) have been experienced by many nations, bringing dramatic economic benefit and prosperity to fossil-fuel industries as well as well being of human society. However, various fossil-fuel related activities emit huge quantities of gaseous, liquid, and solid waste materials, posing a variety of impacts, risks, and liabilities to the environment. Therefore, on the one hand, control measures are desired for effectively managing pollution issues; on the other hand, it becomes extremely critical to invest efforts in finding promising alternative energy sources as solutions to the possible energy shortage crisis in future. This article focuses on both aspects through: (1) a discussion of waste materials generated from fossil-fuel industries and waste management measures; and (2) an exploration of some well-recognized alternative fuels in terms of their nature, availability, production, handling, environmental performances, and current and future applications. The conclusion restates the urgency of finding replaceable long-term alternatives to the conventional fuels.

Alternative fuels for multiple-hearth furnaces

Energy Technology Data Exchange (ETDEWEB)

Bracket, B D; Lawson, T U

1980-04-01

Results are described of a feasibility study on the use of refuse-derived fuel, shredded paper, wood waste, coal, and waste oil in multiple-hearth furnaces at the Lower Molonglo Water Quality Control Centre in Australia. An assessment of waste fuel availability and characteristics is given, and a summary is made of the technical and economic aspects of using these alternative fuels and of minimizing furnace fuel requirements by reducing sludge moisture. The recommended method of reducing fuel oil consumption in the furnace is shown to be sludge drying, using process exhaust heat in a rotary dryer.

Alternate Fuels for Use in Commercial Aircraft

Science.gov (United States)

Daggett, David L.; Hendricks, Robert C.; Walther, Rainer; Corporan, Edwin

2008-01-01

The engine and aircraft Research and Development (R&D) communities have been investigating alternative fueling in near-term, midterm, and far-term aircraft. A drop in jet fuel replacement, consisting of a kerosene (Jet-A) and synthetic fuel blend, will be possible for use in existing and near-term aircraft. Future midterm aircraft may use a biojet and synthetic fuel blend in ultra-efficient airplane designs. Future far-term engines and aircraft in 50-plus years may be specifically designed to use a low- or zero-carbon fuel. Synthetic jet fuels from coal, natural gas, or other hydrocarbon feedstocks are very similar in performance to conventional jet fuel, yet the additional CO2 produced during the manufacturing needs to be permanently sequestered. Biojet fuels need to be developed specifically for jet aircraft without displacing food production. Envisioned as midterm aircraft fuel, if the performance and cost liabilities can be overcome, biofuel blends with synthetic jet or Jet-A fuels have near-term potential in terms of global climatic concerns. Long-term solutions address dramatic emissions reductions through use of alternate aircraft fuels such as liquid hydrogen or liquid methane. Either of these new aircraft fuels will require an enormous change in infrastructure and thus engine and airplane design. Life-cycle environmental questions need to be addressed.

Implications of alternative fuel cycles

International Nuclear Information System (INIS)

Anon.

1978-01-01

The United States is re-examining alternative fuel cycles and nuclear power strategies, and doubtful attempts are being made to justify the economics of the 'throw-away' fuel cycle. At an international forum on 'An acceptable nuclear energy future for the world' at Fort Lauderdale, Karl Cohen of General Electric and a leading authority on this topic put the implications into perspective. Extracts from his address are presented

Alternatives to traditional transportation fuels 1994. Volume 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

In this report, alternative and replacement fuels are defined in accordance with the EPACT. Section 301 of the EPACT defines alternative fuels as: methanol, denatured ethanol, and other alcohols; mixtures containing 85% or more (or such other percentage, but not less than 70%, as determined by the Secretary of Energy, by rule, to provide for requirements relating to cold start, safety, or vehicle functions) by volume of methanol, denatured ethanol, and other alcohols with gasoline or other fuels; natural gas; liquefied petroleum gas; hydrogen; coal-derived liquid fuels; fuels (other than alcohol) derived from biological materials; electricity (including electricity from solar energy); and any other fuel the Secretary determines, by rule, is substantially not petroleum and would yield substantial energy security benefits and substantial environmental benefits. The EPACT defines replacement fuels as the portion of any motor fuel that is methanol, ethanol, or other alcohols, natural gas, liquefied petroleum gas, hydrogen, coal-derived liquid fuels, fuels (other than alcohol) derived from biological materials, electricity (including electricity from solar energy), ethers, or any other fuel the Secretary of Energy determines, by rule, is substantially not petroleum and would yield substantial energy security benefits and substantial environmental benefits. This report covers only those alternative and replacement fuels cited in the EPACT that are currently commercially available or produced in significant quantities for vehicle demonstration purposes. Information about other fuels, such as hydrogen and biodiesel, will be included in later reports as those fuels become more widely used. Annual data are presented for 1992 to 1996. Data for 1996 are based on plans or projections for 1996.

Alternative Fuel News, Volume 4, Number 3

Energy Technology Data Exchange (ETDEWEB)

Ficker, C.

2000-11-14

This issue of Alternative Fuel News focuses on transit buses and refuse haulers. Many transit agencies and waste management companies are investigating alternatives to traditional diesel buses and refuse haulers.

Issues for Storing Plant-Based Alternative Fuels in Marine Environments

Science.gov (United States)

2014-05-09

of aerobic metabolites that exacerbated subsequent corrosion processes. 15. SUBJECT TERMS biodiesel , alternative fuel, seawater, corrosion, carbon...2013 Accepted 17 December 2013 Available online 24 December 2013 Keywords: Biodiesel Alternative fuel Seawater Corrosion Carbon steel...high energy density transportation fuels 13). The feasibility of producing large quantities of fatty acid methyl ester (FAME) and lipid-based fuels

Fuel-cycle greenhouse gas emissions impacts of alternative transportation fuels and advanced vehicle technologies

International Nuclear Information System (INIS)

Wang, M. Q.

1998-01-01

At an international conference on global warming, held in Kyoto, Japan, in December 1997, the United States committed to reduce its greenhouse gas (GHG) emissions by 7% over its 1990 level by the year 2012. To help achieve that goal, transportation GHG emissions need to be reduced. Using Argonne's fuel-cycle model, I estimated GHG emissions reduction potentials of various near- and long-term transportation technologies. The estimated per-mile GHG emissions results show that alternative transportation fuels and advanced vehicle technologies can help significantly reduce transportation GHG emissions. Of the near-term technologies evaluated in this study, electric vehicles; hybrid electric vehicles; compression-ignition, direct-injection vehicles; and E85 flexible fuel vehicles can reduce fuel-cycle GHG emissions by more than 25%, on the fuel-cycle basis. Electric vehicles powered by electricity generated primarily from nuclear and renewable sources can reduce GHG emissions by 80%. Other alternative fuels, such as compressed natural gas and liquefied petroleum gas, offer limited, but positive, GHG emission reduction benefits. Among the long-term technologies evaluated in this study, conventional spark ignition and compression ignition engines powered by alternative fuels and gasoline- and diesel-powered advanced vehicles can reduce GHG emissions by 10% to 30%. Ethanol dedicated vehicles, electric vehicles, hybrid electric vehicles, and fuel-cell vehicles can reduce GHG emissions by over 40%. Spark ignition engines and fuel-cell vehicles powered by cellulosic ethanol and solar hydrogen (for fuel-cell vehicles only) can reduce GHG emissions by over 80%. In conclusion, both near- and long-term alternative fuels and advanced transportation technologies can play a role in reducing the United States GHG emissions

Fuel-cycle greenhouse gas emissions impacts of alternative transportation fuels and advanced vehicle technologies.

Energy Technology Data Exchange (ETDEWEB)

Wang, M. Q.

1998-12-16

At an international conference on global warming, held in Kyoto, Japan, in December 1997, the United States committed to reduce its greenhouse gas (GHG) emissions by 7% over its 1990 level by the year 2012. To help achieve that goal, transportation GHG emissions need to be reduced. Using Argonne's fuel-cycle model, I estimated GHG emissions reduction potentials of various near- and long-term transportation technologies. The estimated per-mile GHG emissions results show that alternative transportation fuels and advanced vehicle technologies can help significantly reduce transportation GHG emissions. Of the near-term technologies evaluated in this study, electric vehicles; hybrid electric vehicles; compression-ignition, direct-injection vehicles; and E85 flexible fuel vehicles can reduce fuel-cycle GHG emissions by more than 25%, on the fuel-cycle basis. Electric vehicles powered by electricity generated primarily from nuclear and renewable sources can reduce GHG emissions by 80%. Other alternative fuels, such as compressed natural gas and liquefied petroleum gas, offer limited, but positive, GHG emission reduction benefits. Among the long-term technologies evaluated in this study, conventional spark ignition and compression ignition engines powered by alternative fuels and gasoline- and diesel-powered advanced vehicles can reduce GHG emissions by 10% to 30%. Ethanol dedicated vehicles, electric vehicles, hybrid electric vehicles, and fuel-cell vehicles can reduce GHG emissions by over 40%. Spark ignition engines and fuel-cell vehicles powered by cellulosic ethanol and solar hydrogen (for fuel-cell vehicles only) can reduce GHG emissions by over 80%. In conclusion, both near- and long-term alternative fuels and advanced transportation technologies can play a role in reducing the United States GHG emissions.

Long-term alternatives for nuclear fuel cycles

International Nuclear Information System (INIS)

Vira, J.; Vieno, T.

1981-07-01

Several technical alternatives have been proposed to the nuclear spent fuel management but the practical experience on any of these is small or totally lacking. Since the management method is also connected with the composition of fresh fuel, the comparison of the alternatives must include the whole fuel cycle of a nuclear power plant. In the planning of the nuclear fuel cycle over a time range of several decades a consideration must be given, in addition, to the potential of the new reactor types with increased efficiency of uranium utilization. For analyses and mutual comparisons of the fuel cycle alternatives a number of computer models have been designed and implemented at the Technical Research Centre of Finland. Given the estimated boundary conditions the models can be used to study the impact of different goals and requirements on the fuel cycle decisions. Further, they facilitate cost predictions and display information on the role of the intrinsic uncertainties in the decision-making. The conclusions of the study are tied to the questions of price and availability of uranium. Hence, for instance, the benefits from the reprocessing of spent fuel might prove to be small when compared to the costs required, especially as the current reprocessing contracts do not allow the custemer to dismiss the duty of building the final disposal facilities for high level radioactive waste. For a few decades the final decisions can be postponed by extending the interim storage period. Farther in the future the decisions in the nuclear fuel cycle arrangements will more link to the introduction of the fast breeder reactors. (author)

Alternative Fuels Data Center: Pennsylvania School Buses Run on Natural Gas

Science.gov (United States)

Pennsylvania School Buses Run on Natural Gas to someone by E-mail Share Alternative Fuels Data Center: Pennsylvania School Buses Run on Natural Gas on Facebook Tweet about Alternative Fuels Data Center: Pennsylvania School Buses Run on Natural Gas on Twitter Bookmark Alternative Fuels Data Center

Alternative Fuels Data Center: How Do Diesel Vehicles Work Using Biodiesel?

Science.gov (United States)

Diesel Vehicles Work Using Biodiesel? to someone by E-mail Share Alternative Fuels Data Center: How Do Diesel Vehicles Work Using Biodiesel? on Facebook Tweet about Alternative Fuels Data Center: How Do Diesel Vehicles Work Using Biodiesel? on Twitter Bookmark Alternative Fuels Data Center: How Do

Alternative transport fuels: supply, consumption and conservation

International Nuclear Information System (INIS)

Trindade, S.C.

1990-01-01

Road-based passenger and freight transport almost exclusively uses petroleum/hydrocarbon fuels in the fluid form. These fuels will probably continue to be major transport fuels well into the 21st century. As such there is need to prolong their use which can be done through: (1) conservation of fuel by increasing efficiency of internal combustion engines, and (2) conversion of natural gas, coal and peat, and biomass into alternate fuels such as ethanol, methanol, CNG, LNG, LPG, low heat-content (producer) gas and vegetable oils. Research, development and demonstration (RD and D) priorities in supply, consumption and conservation of these alternate fuels are identified and ranked in the context of situation prevailing in Brazil. Author has assigned the highest priority for research in the impact of pricing, economic, fiscal and trade policies, capital allocation criteria and institutional and legislative framework. It has also been emphasised that an integrated or systems approach is mandatory to achieve net energy gains in transport sector. (M.G.B.). 33 refs., 11 tabs., 4 figs

Comparison of spent fuel management fee collection alternatives

International Nuclear Information System (INIS)

White, M.K.; Engel, R.L.

1979-01-01

Five alternative methods for recovering the costs of spent fuel management were evaluated. These alternatives consist of collecting the fee for various components of spent fuel management cost (AFR basin storage, transportation from AFR basin to the repository, packaging, repository, R and D, and government overhead) at times ranging from generation of power to delivery of the spent fuel to the government. The five fee collection mechanisms were analyzed to determine how well they serve the interests of the public and the electricity ratepayer

Alternative fuel cycles and non-proliferation aspects

International Nuclear Information System (INIS)

Kessler, G.

1980-10-01

The most important physical characteristics of the U/Pu and the Th/U fuel cycles and the technical data of the most significant converter reactors operating with Th/U fuel are outlined in the report. Near breeders as well as breeders with a thermal neutron spectrum are briefly discussed, and the potential of breeders with fast neutron spectra in the Th/U fuel is outlined. The essential criteria for the comparison of the alternative fuel cycles with the reference Pu/U cycle are the consumption of natural uranium, the numbers of U-233 producing and U-233 consuming converter reactors and the amounts of fission material transported and handled within the fuel cycle (reprocessing, refabrication). Although the alternative U/Th fuel cycles are feasible with some advantages and some disadvantages as compared to the reference U/Pu cycle, not much experience has so far been gathered with pilot plants of the fuel cycle. The respective status in reprocessing, refabrication and waste disposal is briefly discussed. Finally, a comparison of the risk potential inherent in secular storage is presented and questions of resistance to proliferation and of safeguards of the U/Th cycle are discussed

Solar energy as a viable and sustainable alternative to fossil fuel

International Nuclear Information System (INIS)

Mohammed, F.L.; Ewansiha, K.; Enyeribe, E.

2007-01-01

A lot of human and natural resources have been put in the energy sector, but the quantity of supply to consumers is quite inadequate. To sustain industrial output and ensure rapid growth, there is a need for a reliable and efficient supply of energy. A survey was carried out to find out the knowledge of consumers on the use of solar energy as an alternative source of energy.The result indicated that although people are aware of existence, the product is not readily available for man

Alternative Fuels Data Center: Central Ohio Turns Trash Into Natural Gas

Science.gov (United States)

Central Ohio Turns Trash Into Natural Gas to someone by E-mail Share Alternative Fuels Data Center : Central Ohio Turns Trash Into Natural Gas on Facebook Tweet about Alternative Fuels Data Center: Central Ohio Turns Trash Into Natural Gas on Twitter Bookmark Alternative Fuels Data Center: Central Ohio Turns

Alternate aircraft fuels prospects and operational implications

Science.gov (United States)

Witcofski, R. D.

1977-01-01

The paper discusses NASA studies of the potentials of coal-derived aviation fuels, specifically synthetic aviation kerosene, liquid methane, and liquid hydrogen. Topics include areas of fuel production, air terminal requirements for aircraft fueling (for liquid hydrogen only), and the performance characteristics of aircraft designed to utilize alternate fuels. Energy requirements associated with the production of each of the three selected fuels are determined, and fuel prices are estimated. Subsonic commercial air transports using liquid hydrogen fuel have been analyzed, and their performance and the performance of aircraft which use commercial aviation kerosene are compared. Environmental and safety issues are considered.

Alternative Fuels Data Center: Yellowstone Park Recycles Vehicle Batteries

Science.gov (United States)

for Solar Power Yellowstone Park Recycles Vehicle Batteries for Solar Power to someone by E -mail Share Alternative Fuels Data Center: Yellowstone Park Recycles Vehicle Batteries for Solar Power on Facebook Tweet about Alternative Fuels Data Center: Yellowstone Park Recycles Vehicle Batteries

Spent Nuclear Fuel Alternative Technology Decision Analysis

International Nuclear Information System (INIS)

Shedrow, C.B.

1999-01-01

The Westinghouse Savannah River Company (WSRC) made a FY98 commitment to the Department of Energy (DOE) to recommend a technology for the disposal of aluminum-based spent nuclear fuel (SNF) at the Savannah River Site (SRS). The two technologies being considered, direct co-disposal and melt and dilute, had been previously selected from a group of eleven potential SNF management technologies by the Research Reactor Spent Nuclear Fuel Task Team chartered by the DOE''s Office of Spent Fuel Management. To meet this commitment, WSRC organized the SNF Alternative Technology Program to further develop the direct co-disposal and melt and dilute technologies and ultimately provide a WSRC recommendation to DOE on a preferred SNF alternative management technology

Alternative Fuels Data Center: Hybrid and Plug-In Electric Vehicle

Science.gov (United States)

Conversions Hybrid and Plug-In Electric Vehicle Conversions to someone by E-mail Share Alternative Fuels Data Center: Hybrid and Plug-In Electric Vehicle Conversions on Facebook Tweet about Alternative Fuels Data Center: Hybrid and Plug-In Electric Vehicle Conversions on Twitter Bookmark Alternative

Dynamic modeling and analysis of alternative fuel cycle scenarios in Korea

International Nuclear Information System (INIS)

Jeong, Chang Joon; Choi, Hang Bok

2007-01-01

The Korean nuclear fuel cycle was modeled by the dynamic analysis method, which was applied to the once-through and alternative fuel cycles. First, the once-through fuel cycle was analyzed based on the Korean nuclear power plant construction plan up to 2015 and a postulated nuclear demand growth rate of zero after 2015. Second, alternative fuel cycles including the direct use of spent pressurized water reactor fuel in Canada deuterium reactors (DUPIC), a sodium-cooled fast reactor and an accelerator driven system were assessed and the results were compared with those of the once-through fuel cycle. The once-through fuel cycle calculation showed that the nuclear power demand would be 25 GWe and the amount of the spent fuel will be ∼65000 tons by 2100. The alternative fuel cycle analyses showed that the spent fuel inventory could be reduced by more than 30% and 90% through the DUPIC and fast reactor fuel cycles, respectively, when compared with the once-through fuel cycle. The results of this study indicate that both spent fuel and uranium resources can be effectively managed if alternative reactor systems are timely implemented along with the existing reactors

Guide to alternative fuel vehicle incentives and laws: September 1998

Energy Technology Data Exchange (ETDEWEB)

Riley, C.; O' Connor, K.

1998-12-22

This guide provides information in support of the National Clean Cities Program, which will assist one in becoming better informed about the choices and options surrounding the use of alternative fuels and the purchase of alternative fuel vehicles. The information printed in this guide is current as of September 15, 1998. For recent additions or more up-to-date information, check the Alternative Fuels Data Center Web site at http://www.afdc.doe.gov

Alternative Fuels Data Center: Recycled Cooking Oil Powers Biodiesel

Science.gov (United States)

Vehicles in Vermont Recycled Cooking Oil Powers Biodiesel Vehicles in Vermont to someone by E -mail Share Alternative Fuels Data Center: Recycled Cooking Oil Powers Biodiesel Vehicles in Vermont on Facebook Tweet about Alternative Fuels Data Center: Recycled Cooking Oil Powers Biodiesel Vehicles in

Alternative Fuels Data Center: Landfills Convert Biogas Into Renewable

Science.gov (United States)

Natural Gas Landfills Convert Biogas Into Renewable Natural Gas to someone by E-mail Share Alternative Fuels Data Center: Landfills Convert Biogas Into Renewable Natural Gas on Facebook Tweet about Alternative Fuels Data Center: Landfills Convert Biogas Into Renewable Natural Gas on Twitter Bookmark

Systems impacts of spent fuel disassembly alternatives

International Nuclear Information System (INIS)

1984-07-01

Three studies were completed to evaluate four alternatives to the disposal of intact spent fuel assemblies in a geologic repository. A preferred spent fuel waste form for disposal was recommended on consideration of (1) package design and fuel/package interaction, (2) long-term, in-repository performance of the waste form, and (3) overall process performance and costs for packaging, handling, and emplacement. The four basic alternative waste forms considered were (1) end fitting removal, (2) fission gas venting, (3) disassembly and close packing, and (4) shearing/immobilization. None of the findings ruled out any alternative on the basis of waste package considerations or long-term performance of the waste form. The third alternative offers flexibility in loading that may prove attractive in the various geologic media under consideration, greatly reduces the number of packages, and has the lowest unit cost. These studies were completed in October, 1981. Since then Westinghouse Electric Corporation and the Office of Nuclear Waste Isolation have completed studies in related fields. This report is now being published to provide publicly the background material that is contained within. 47 references, 28 figures, 31 tables

Alternate fusion fuels workshop

International Nuclear Information System (INIS)

1981-06-01

The workshop was organized to focus on a specific confinement scheme: the tokamak. The workshop was divided into two parts: systems and physics. The topics discussed in the systems session were narrowly focused on systems and engineering considerations in the tokamak geometry. The workshop participants reviewed the status of system studies, trade-offs between d-t and d-d based reactors and engineering problems associated with the design of a high-temperature, high-field reactor utilizing advanced fuels. In the physics session issues were discussed dealing with high-beta stability, synchrotron losses and transport in alternate fuel systems. The agenda for the workshop is attached

Preferences for alternative fuel vehicles by Dutch local governments

NARCIS (Netherlands)

Rijnsoever, F.J. van; Hagen, P.; Willems, M

2013-01-01

Using a choice model, we estimate the preferences for alternative fuel vehicles by Dutch local governments. The analysis shows that local governments are willing to pay between 25% and 50% extra for an alternative fuel vehicle without a serious loss of utility. Further, local emissions are an

Alternative Fuel for Marine Application

Science.gov (United States)

2012-02-29

The U.S. Maritime Administration (MARAD) is participating in the U.S. Navy's ongoing efforts to test alternative fuels for marine use by demonstrating their applicability on commercial vessels. In support of this effort, the Navy provided neat hydrot...

Alternate-Fueled Combustor-Sector Performance

Science.gov (United States)

Thomas, Anna E.; Saxena, Nikita T.; Shouse, Dale T.; Neuroth, Craig; Hendricks, Robert C.; Lynch, Amy; Frayne, Charles W.; Stutrud, Jeffrey S.; Corporan, Edwin; Hankins, Terry

2013-01-01

In order to realize alternative fueling for military and commercial use, the industry has set forth guidelines that must be met by each fuel. These aviation fueling requirements are outlined in MIL-DTL-83133F(2008) or ASTM D 7566 Annex (2011) standards, and are classified as "drop-in" fuel replacements. This report provides combustor performance data for synthetic-paraffinic-kerosene- (SPK-) type (Fischer-Tropsch (FT)) fuel and blends with JP-8+100, relative to JP-8+100 as baseline fueling. Data were taken at various nominal inlet conditions: 75 psia (0.52 MPa) at 500 degF (533 K), 125 psia (0.86 MPa) at 625 degF (603 K), 175 psia (1.21 MPa) at 725 degF (658 K), and 225 psia (1.55 MPa) at 790 degF (694 K). Combustor performance analysis assessments were made for the change in flame temperatures, combustor efficiency, wall temperatures, and exhaust plane temperatures at 3, 4, and 5 percent combustor pressure drop (DP) for fuel:air ratios (F/A) ranging from 0.010 to 0.025. Significant general trends show lower liner temperatures and higher flame and combustor outlet temperatures with increases in FT fueling relative to JP-8+100 fueling. The latter affects both turbine efficiency and blade and vane lives.

Modelling of spray evaporation and penetration for alternative fuels

OpenAIRE

Azami, M. H.; Savill, Mark A.

2016-01-01

The focus of this work is on the modelling of evaporation and spray penetration for alternative fuels. The extension model approach is presented and validated for alternative fuels, namely, Kerosene (KE), Ethanol (ETH), Methanol (MTH), Microalgae biofuel (MA), Jatropha biofuel (JA), and Camelina biofuel (CA). The results for atomization and spray penetration are shown in a time variant condition. Comparisons have been made to visualize the transient behaviour of these fuels. The vapour pressu...

Spent Nuclear Fuel Alternative Technology Decision Analysis

Energy Technology Data Exchange (ETDEWEB)

Shedrow, C.B.

1999-11-29

The Westinghouse Savannah River Company (WSRC) made a FY98 commitment to the Department of Energy (DOE) to recommend a technology for the disposal of aluminum-based spent nuclear fuel (SNF) at the Savannah River Site (SRS). The two technologies being considered, direct co-disposal and melt and dilute, had been previously selected from a group of eleven potential SNF management technologies by the Research Reactor Spent Nuclear Fuel Task Team chartered by the DOE''s Office of Spent Fuel Management. To meet this commitment, WSRC organized the SNF Alternative Technology Program to further develop the direct co-disposal and melt and dilute technologies and ultimately provide a WSRC recommendation to DOE on a preferred SNF alternative management technology.

Alternative Fuels Data Center: Hybrid Electric Vehicles

Science.gov (United States)

. A wide variety of hybrid electric vehicle models is currently available. Although HEVs are often -go traffic), further improving fuel economy. Mild hybrid systems cannot power the vehicle using Hybrid Electric Vehicles to someone by E-mail Share Alternative Fuels Data Center: Hybrid Electric

HFIR spent fuel management alternatives

International Nuclear Information System (INIS)

Begovich, J.M.; Green, V.M.; Shappert, L.B.; Lotts, A.L.

1992-01-01

The High Flux Isotope Reactor (HFIR) at Martin Marietta Energy Systems' Oak Ridge National Laboratory (ORNL) has been unable to ship its spent fuel to Savannah River Site (SRS) for reprocessing since 1985. The HFIR storage pools are expected to fill up in the February 1994 to February 1995 time frame. If a management altemative to existing HFIR pool storage is not identified and implemented before the HFIR pools are full, the HFIR will be forced to shut down. This study investigated several alternatives for managing the HFIR spent fuel, attempting to identify options that could be implemented before the HFIR pools are full. The options investigated were: installing a dedicated dry cask storage facility at ORNL, increasing HFIR pool storage capacity by clearing the HFIR pools of debris and either close-packing or stacking the spent fuel elements, storing the spent fuel at another ORNL pool, storing the spent fuel in one or more hot cells at ORNL, and shipping the spent fuel offsite for reprocessing or storage elsewhere

Treatment alternatives for non-fuel-bearing hardware

International Nuclear Information System (INIS)

Ross, W.A.; Clark, L.L.; Oma, K.H.

1987-01-01

This evaluation compared four alternatives for the treatment or processing of non-fuel bearing hardware (NFBH) to reduce its volume and prepare it for disposal. These treatment alternatives are: shredding; shredding and low pressure compaction; shredding and supercompaction; and melting. These alternatives are compared on the basis of system costs, waste form characteristics, and process considerations. The study recommends that melting and supercompaction alternatives be further considered and that additional testing be conducted for these two alternatives

Review of alternative fuels data bases

Science.gov (United States)

Harsha, P. T.; Edelman, R. B.

1983-01-01

Based on an analysis of the interaction of fuel physical and chemical properties with combustion characteristics and indicators, a ranking of the importance of various fuel properties with respect to the combustion process was established. This ranking was used to define a suite of specific experiments whose objective is the development of an alternative fuels design data base. Combustion characteristics and indicators examined include droplet and spray formation, droplet vaporization and burning, ignition and flame stabilization, flame temperature, laminar flame speed, combustion completion, soot emissions, NOx and SOx emissions, and the fuels' thermal and oxidative stability and fouling and corrosion characteristics. Key fuel property data is found to include composition, thermochemical data, chemical kinetic rate information, and certain physical properties.

Estimates of Canadian fuel fabrication costs for alternative fuel cycles and systems

International Nuclear Information System (INIS)

Blahnik, C.

1979-04-01

Unit fuel fabrication costs are estimated for alternate fuel cycles and systems that may be of interest in Ontario Hydro's strategy analyses. A method is proposed for deriving the unit fuel fabrication price to be paid by a Canadian utility as a function of time (i.e. the price that reflects the changing demand/supply situation in the particular scenario considered). (auth)

Spent Nuclear Fuel Alternative Technology Risk Assessment

Energy Technology Data Exchange (ETDEWEB)

Perella, V.F.

1999-11-29

A Research Reactor Spent Nuclear Fuel Task Team (RRTT) was chartered by the Department of Energy (DOE) Office of Spent Fuel Management with the responsibility to recommend a course of action leading to a final technology selection for the interim management and ultimate disposition of the foreign and domestic aluminum-based research reactor spent nuclear fuel (SNF) under DOE''s jurisdiction. The RRTT evaluated eleven potential SNF management technologies and recommended that two technologies, direct co-disposal and an isotopic dilution alternative, either press and dilute or melt and dilute, be developed in parallel. Based upon that recommendation, the Westinghouse Savannah River Company (WSRC) organized the SNF Alternative Technology Program to further develop the direct co-disposal and melt and dilute technologies and provide a WSRC recommendation to DOE for a preferred SNF alternative management technology. A technology risk assessment was conducted as a first step in this recommendation process to determine if either, or both, of the technologies posed significant risks that would make them unsuitable for further development. This report provides the results of that technology risk assessment.

Spent Nuclear Fuel Alternative Technology Risk Assessment

International Nuclear Information System (INIS)

Perella, V.F.

1999-01-01

A Research Reactor Spent Nuclear Fuel Task Team (RRTT) was chartered by the Department of Energy (DOE) Office of Spent Fuel Management with the responsibility to recommend a course of action leading to a final technology selection for the interim management and ultimate disposition of the foreign and domestic aluminum-based research reactor spent nuclear fuel (SNF) under DOE''s jurisdiction. The RRTT evaluated eleven potential SNF management technologies and recommended that two technologies, direct co-disposal and an isotopic dilution alternative, either press and dilute or melt and dilute, be developed in parallel. Based upon that recommendation, the Westinghouse Savannah River Company (WSRC) organized the SNF Alternative Technology Program to further develop the direct co-disposal and melt and dilute technologies and provide a WSRC recommendation to DOE for a preferred SNF alternative management technology. A technology risk assessment was conducted as a first step in this recommendation process to determine if either, or both, of the technologies posed significant risks that would make them unsuitable for further development. This report provides the results of that technology risk assessment

The DUPIC alternative for backend fuel cycle

International Nuclear Information System (INIS)

Lee, J.S.; Choi, J.W.; Park, H.S.; Boczar, P.; Sullivan, J.; Gadsby, R.D.

1997-01-01

From the early nineties, a research programme, called DUPIC (Direct Use of Spent PWR Fuel in CANDU) has been undertaken in an international exercise involving Korea, Canada, the U.S. and later the IAEA. The basic idea of this fuel cycle alternative is that the spent fuel from LWR contains enough fissile remnant to be burnt again in CANDUs thanks to its excellent neutron economy. A systematic R and D plan has now gained a full momentum to verify experimentally the DUPIC fuel cycle concept. 4 refs

Tracking costs of alternatively fueled buses in Florida : [summary].

Science.gov (United States)

2011-01-01

In an effort to address rising fuel costs and environmental concerns, many transit agencies across Florida have introduced alternative fuel technologies to their traditional diesel-powered fleets. Fuel types include biodiesel, compressed natural gas,...

Comparison of spent nuclear fuel management alternatives

International Nuclear Information System (INIS)

Beebe, C.L.; Caldwell, M.A.

1996-01-01

This paper reports the process an results of a trade study of spent nuclear fuel (SNF)management alternatives. The purpose of the trade study was to provide: (1) a summary of various SNF management alternatives, (2) an objective comparison of the various alternatives to facilitate the decision making process, and (3) documentation of trade study rational and the basis for decisions

Development of alternative fuel for pressurized water reactors

International Nuclear Information System (INIS)

Cardoso, P.E.; Ferreira, R.A.N.; Ferraz, W.B.; Lameiras, F.S.; Santos, A.; Assis, G. de; Doerr, W.O.; Wehner, E.L.

1984-01-01

The utilization of alternative fuel cycles in Pressurized Water Reactors (PWR) such as Th/U and Th/Pu cycles can permit a better utilization of uranium reserves without the necessity of developing new power reactor concepts. The development of the technology of alternative fuels for PWR is one of the objectives of the 'Program on Thorium Utilization in Pressurized Water Reactors' carried out jointly by Empresas Nucleares Brasileiras S.A. (NUCLEBRAS), through its Centro de Desenvolvimento da Tecnologia Nuclear (CDTN) and by German institutions, the Julich Nuclear Research Center (KFA), the Kraftwerk Union A.G. (KWU) and NUKEM GmbH. This paper summarizes the results so far obtained in the fuel technology. The development of a fabrication process for PWR fuel pellets from gel-microspheres is reported as well as the design, the specification, and the fabrication of prototype fuel rods for irradiation tests. (Author) [pt

Alternative fuels in fire debris analysis: biodiesel basics.

Science.gov (United States)

Stauffer, Eric; Byron, Doug

2007-03-01

Alternative fuels are becoming more prominent on the market today and, soon, fire debris analysts will start seeing them in liquid samples or in fire debris samples. Biodiesel fuel is one of the most common alternative fuels and is now readily available in many parts of the United States and around the world. This article introduces biodiesel to fire debris analysts. Biodiesel fuel is manufactured from vegetable oils and/or animal oils/fats. It is composed of fatty acid methyl esters (FAMEs) and is sold pure or as a blend with diesel fuel. When present in fire debris samples, it is recommended to extract the debris using passive headspace concentration on activated charcoal, possibly followed by a solvent extraction. The gas chromatographic analysis of the extract is first carried out with the same program as for regular ignitable liquid residues, and second with a program adapted to the analysis of FAMEs.

Bioethanol from poplar: a commercially viable alternative to fossil fuel in the European Union.

Science.gov (United States)

Littlewood, Jade; Guo, Miao; Boerjan, Wout; Murphy, Richard J

2014-01-01

The European Union has made it a strategic objective to develop its biofuels market in order to minimize greenhouse gas (GHG) emissions, to help mitigate climate change and to address energy insecurity within the transport sector. Despite targets set at national and supranational levels, lignocellulosic bioethanol production has yet to be widely commercialized in the European Union. Here, we use techno-economic modeling to compare the price of bioethanol produced from short rotation coppice (SRC) poplar feedstocks under two leading processing technologies in five European countries. Our evaluation shows that the type of processing technology and varying national costs between countries results in a wide range of bioethanol production prices (€0.275 to 0.727/l). The lowest production prices for bioethanol were found in countries that had cheap feedstock costs and high prices for renewable electricity. Taxes and other costs had a significant influence on fuel prices at the petrol station, and therefore the presence and amount of government support for bioethanol was a major factor determining the competitiveness of bioethanol with conventional fuel. In a forward-looking scenario, genetically engineering poplar with a reduced lignin content showed potential to enhance the competitiveness of bioethanol with conventional fuel by reducing overall costs by approximately 41% in four out of the five countries modeled. However, the possible wider phenotypic traits of advanced poplars needs to be fully investigated to ensure that these do not unintentionally negate the cost savings indicated. Through these evaluations, we highlight the key bottlenecks within the bioethanol supply chain from the standpoint of various stakeholders. For producers, technologies that are best suited to the specific feedstock composition and national policies should be optimized. For policymakers, support schemes that benefit emerging bioethanol producers and allow renewable fuel to be

Alternative Fuels Data Center: New Hampshire Fleet Revs up With Natural Gas

Science.gov (United States)

New Hampshire Fleet Revs up With Natural Gas to someone by E-mail Share Alternative Fuels Data Center: New Hampshire Fleet Revs up With Natural Gas on Facebook Tweet about Alternative Fuels Data Center: New Hampshire Fleet Revs up With Natural Gas on Twitter Bookmark Alternative Fuels Data Center

Alternative general-aircraft engines

Science.gov (United States)

Tomazic, W. A.

1976-01-01

The most promising alternative engine (or engines) for application to general aircraft in the post-1985 time period was defined, and the level of technology was cited to the point where confident development of a new engine can begin early in the 1980's. Low emissions, multifuel capability, and fuel economy were emphasized. Six alternative propulsion concepts were considered to be viable candidates for future general-aircraft application: the advanced spark-ignition piston, rotary combustion, two- and four-stroke diesel, Stirling, and gas turbine engines.

Alternative fuels for the French fast breeder reactors programme

International Nuclear Information System (INIS)

Bailly, H.; Bernard, H.; Mansard, B.

1989-01-01

French fast breeder reactors use mixed oxide as reference fuel. A great deal of experience has been gained in the behaviour and manufacture of oxide fuel, which has proved to be the most suitable fuel for future commercial breeder reactors. However, France is maintaining long-term alternative fuels programme, in order to be in a position to satisfy eventually new future reactor design and operational requirements. Initially, the CEA in France developed a carbide-based, sodium-bonded fuel designed for a high specific power. The new objective of the alternative fuels programme is to define a fuel which could replace the oxide without requiring any significant changes to the operating conditions, fuel cycle processes or facilities. The current program concentrates on a nitride-based, helium-bonded fuel, bearing in mind the carbide solution. The paper describes the main characteristics required, the manufacturing process as developed, the inspection methods, and the results obtained. Present indications are that the industrial manufacture of mixed nitride is feasible and that production costs for nitride and oxide fuels would be not significantly different. (author) 8 refs., 2 figs

Geography of Existing and Potential Alternative Fuel Markets in the United States

Energy Technology Data Exchange (ETDEWEB)

Johnson, C.; Hettinger, D.

2014-11-01

When deploying alternative fuels, it is paramount to match the right fuel with the right location, in accordance with local market conditions. We used six market indicators to evaluate the existing and potential regional market health for each of the five most commonly deployed alternative fuels: electricity (used by plug-in electric vehicles), biodiesel (blends of B20 and higher), E85 ethanol, compressed natural gas (CNG), and propane. Each market indicator was mapped, combined, and evaluated by industry experts. This process revealed the weight the market indicators should be given, with the proximity of fueling stations being the most important indicator, followed by alternative fuel vehicle density, gasoline prices, state incentives, nearby resources, and finally, environmental benefit. Though markets vary among states, no state received 'weak' potential for all five fuels, indicating that all states have an opportunity to use at least one alternative fuel. California, Illinois, Indiana, Pennsylvania, and Washington appear to have the best potential markets for alternative fuels in general, with each sporting strong markets for four of the fuels. Wyoming showed the least potential, with weak markets for all alternative fuels except for CNG, for which it has a patchy market. Of all the fuels, CNG is promising in the greatest number of states--largely because freight traffic provides potential demand for many far-reaching corridor markets and because the sources of CNG are so widespread geographically.

Alternative Fuels Data Center: Cities Make the Clean Switch to Natural Gas

Science.gov (United States)

Cities Make the Clean Switch to Natural Gas to someone by E-mail Share Alternative Fuels Data Center: Cities Make the Clean Switch to Natural Gas on Facebook Tweet about Alternative Fuels Data Center : Cities Make the Clean Switch to Natural Gas on Twitter Bookmark Alternative Fuels Data Center: Cities

Alternative fuels for vehicles fleet demonstration program. Final report, volume 2: Appendices

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

The Alternative Fuels for Vehicles Fleet Demonstration Program (AFV-FDP) was a multiyear effort to collect technical data for use in determining the costs and benefits of alternative-fuel vehicles (AFVs) in typical applications in New York State. This report, Volume 2, includes 13 appendices to Volume 1 that expand upon issues raised therein. Volume 1 provides: (1) Information about the purpose and scope of the AFV-FDP; (2) A summary of AFV-FDP findings organized on the basis of vehicle type and fuel type; (3) A short review of the status of AFV technology development, including examples of companies in the State that are active in developing AFVs and AFV components; and (4) A brief overview of the status of AFV deployment in the State. Volume 3 provides expanded reporting of AFV-FDP technical details, including the complete texts of the brochure Garage Guidelines for Alternative Fuels and the technical report Fleet Experience Survey Report, plus an extensive glossary of AFV terminology. The appendices cover a wide range of issues including: emissions regulations in New York State; production and health effects of ozone; vehicle emissions and control systems; emissions from heavy-duty engines; reformulated gasoline; greenhouse gases; production and characteristics of alternative fuels; the Energy Policy Act of 1992; the Clean Fuel Fleet Program; garage design guidelines for alternative fuels; surveys of fleet managers using alternative fuels; taxes on conventional and alternative fuels; and zero-emission vehicle technology.

Alternatives to traditional transportation fuels 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

This report provides information on transportation fuels other than gasoline and diesel, and the vehicles that use these fuels. The Energy Information Administration (EIA) provides this information to support the U.S. Department of Energy`s reporting obligations under Section 503 of the Energy Policy Act of 1992 (EPACT). The principal information contained in this report includes historical and year-ahead estimates of the following: (1) the number and type of alterative-fueled vehicles (AFV`s) in use; (2) the consumption of alternative transportation fuels and {open_quotes}replacement fuels{close_quotes}; and (3) the number and type of alterative-fueled vehicles made available in the current and following years. In addition, the report contains some material on special topics. The appendices include a discussion of the methodology used to develop the estimates (Appendix A), a map defining geographic regions used, and a list of AFV suppliers.

Alternative Fuel and Advanced Technology Commercial Lawn Equipment

Energy Technology Data Exchange (ETDEWEB)

None

2014-10-10

The U.S. Department of Energy's Clean Cities program produced this guide to help inform the commercial mowing industry about product options and potential benefits. This guide provides information about equipment powered by propane, ethanol, compressed natural gas, biodiesel, and electricity, as well as advanced engine technology. In addition to providing an overview for organizations considering alternative fuel lawn equipment, this guide may also be helpful for organizations that want to consider using additional alternative fueled equipment.

Alternative Fuels Data Center: Wisconsin Reduces Emissions With Natural Gas

Science.gov (United States)

Trucks Wisconsin Reduces Emissions With Natural Gas Trucks to someone by E-mail Share Alternative Fuels Data Center: Wisconsin Reduces Emissions With Natural Gas Trucks on Facebook Tweet about Alternative Fuels Data Center: Wisconsin Reduces Emissions With Natural Gas Trucks on Twitter Bookmark

Alternative Fuels Data Center: Renewable Natural Gas From Landfill Powers

Science.gov (United States)

Refuse Vehicles Renewable Natural Gas From Landfill Powers Refuse Vehicles to someone by E-mail Share Alternative Fuels Data Center: Renewable Natural Gas From Landfill Powers Refuse Vehicles on Facebook Tweet about Alternative Fuels Data Center: Renewable Natural Gas From Landfill Powers Refuse

Alternative Fuels Data Center: Hybrid and Electric Vehicles Boom Coast to

Science.gov (United States)

Coast Hybrid and Electric Vehicles Boom Coast to Coast to someone by E-mail Share Alternative Fuels Data Center: Hybrid and Electric Vehicles Boom Coast to Coast on Facebook Tweet about Alternative Fuels Data Center: Hybrid and Electric Vehicles Boom Coast to Coast on Twitter Bookmark Alternative

Alternative Fuels Data Center: Virginia Cleans up With Natural Gas Refuse

Science.gov (United States)

Trucks Virginia Cleans up With Natural Gas Refuse Trucks to someone by E-mail Share Alternative Fuels Data Center: Virginia Cleans up With Natural Gas Refuse Trucks on Facebook Tweet about Alternative Fuels Data Center: Virginia Cleans up With Natural Gas Refuse Trucks on Twitter Bookmark Alternative

Alternative Fuels Data Center: Little Rock Gains Momentum with Natural Gas

Science.gov (United States)

Buses Little Rock Gains Momentum with Natural Gas Buses to someone by E-mail Share Alternative Fuels Data Center: Little Rock Gains Momentum with Natural Gas Buses on Facebook Tweet about Alternative Fuels Data Center: Little Rock Gains Momentum with Natural Gas Buses on Twitter Bookmark Alternative

Alternative Fuels Data Center: Federal Laws and Incentives for Electricity

Science.gov (United States)

and 49 U.S. Code 47136a) Advanced Technology Vehicle (ATV) and Alternative Fuel Infrastructure Manufacturing Loan Program website and the Alternative Fuel Infrastructure fact sheet. (Reference 42 U.S. Code vehicles and infrastructure. Projects supported with CMAQ funds must demonstrate emissions reductions, be

Potentials and limitations of alternative fuels for diesel engine

Directory of Open Access Journals (Sweden)

Gligorijević Radinko

2009-01-01

Full Text Available The primary energy consumption in the world has increased continuously. The most important primary energy source is oil. The supply of automotive fuels today is based almost entirely on oil, and the demand for liquid transportation fuels worldwide will rise significantly in the next fifty years. Growing energy consumption and decreasing fossil resources are reasons for increasing prices of fossil fuel. Besides limited availability, contribution to greenhouse effect and pollutant emission represent another problem of fossil fuel. Both of these problems can be overcome by increased application of renewable biofuels. Therefore, great effort is made to supplement the primary energy sources by including renewable energies. There are alternative fuels 1st and 2nd generation. Some of them show high potential for reduction of engine out emission. But there are economical and technical barriers when such fuels are applied. This paper shows both advantage and disadvantage of alternative fuels, especially when used for diesel engines.

76 FR 67287 - Alternative Fuel Transportation Program; Alternative Fueled Vehicle Credit Program (Subpart F...

Science.gov (United States)

2011-10-31

... additional credits for the use of biodiesel in blends of 20 percent biodiesel or greater and have provided an... discussion in Part II.A), the original program based upon AFV acquisitions and biodiesel use became known as... example, B20 (a 20 percent blend of biodiesel with 80 percent petroleum diesel) is not an alternative fuel...

Alternatives for water basin spent fuel storage: executive summary and comparative evaluation

International Nuclear Information System (INIS)

Viebrock, J.M.

1979-09-01

A five part report identifies and evaluates alternatives to conventional methods for water basin storage of irradiated light water reactor fuel assemblies (spent fuel). A recommendation is made for development or further evaluation of one attractive alternative: Proceed to develop fuel disassembly with subsequent high density storage of fuel pins (pin storage). The storage alternatives were evaluated for emplacement at reactor, in existing away-from-reactor storage facilities and in new away-from-reactor facilities. In the course of the study, the work effort necessarily extended beyond the pool wall in scope to properly assess the affects of storage alternatives on AFT systems

77 FR 18718 - Petroleum Reduction and Alternative Fuel Consumption Requirements for Federal Fleets

Science.gov (United States)

2012-03-28

... Petroleum Reduction and Alternative Fuel Consumption Requirements for Federal Fleets AGENCY: Office of...-required reduction in petroleum consumption and increase in alternative fuel consumption for Federal fleets... regulations for a statutorily-required reduction in petroleum consumption and increase in alternative fuel...

76 FR 5319 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

Science.gov (United States)

2011-01-31

... Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline AGENCY: Environmental... gasoline. This proposed rule will provide flexibility to the regulated community by allowing an additional... A. Alternative Test Method for Olefins in Gasoline III. Statutory and Executive Order Reviews A...

Spray and atomization of diesel fuel and its alternatives from a single-hole injector using a common rail fuel injection system

KAUST Repository

Chen, PinChia

2013-01-01

Fuel spray and atomization characteristics play an important role in the performance of internal combustion engines. As the reserves of petroleum fuel are expected to be depleted within a few decades, finding alternative fuels that are economically viable and sustainable to replace the petroleum fuel has attracted much research attention. In this work, the spray and atomization characteristics were investigated for commercial No. 2 diesel fuel, biodiesel (FAME) derived from waste cooking oil (B100), 20% biodiesel blended diesel fuel (B20), renewable diesel fuel produced in house, and civil aircraft jet fuel (Jet-A). Droplet diameters and particle size distributions were measured by a laser diffraction particle analyzing system and the spray tip penetrations and cone angles were acquired using a high speed imaging technique. All experiments were conducted by employing a common-rail high-pressure fuel injection system with a single-hole nozzle under room temperature and pressure. The experimental results showed that biodiesel and jet fuel had different features compared with diesel. Longer spray tip penetration and larger droplet diameters were observed for B100. The smaller droplet size of the Jet-A were believed to be caused by its relatively lower viscosity and surface tension. B20 showed similar characteristics to diesel but with slightly larger droplet sizes and shorter tip penetration. Renewable diesel fuel showed closer droplet size and spray penetration to Jet-A with both smaller than diesel. As a result, optimizing the trade-off between spray volume and droplet size for different fuels remains a great challenge. However, high-pressure injection helps to optimize the trade-off of spray volume and droplet sizes. Furthermore, it was observed that the smallest droplets were within a region near the injector nozzle tip and grew larger along the axial and radial direction. The variation of droplet diameters became smaller with increasing injection pressure. �

Alternative transportation fuels in the USA: government hydrogen vehicle programs

International Nuclear Information System (INIS)

Cannon, J.S.

1993-01-01

The linkage between natural gas-based transportation and hydrogen-based transportation strategies, two clean burning gaseous fuels, provides a strong policy rationale for increased government sponsorship of hydrogen vehicle research and demonstration programs. Existing federal and state government hydrogen vehicle projects are discussed in this paper: research at the NREL, alternate-fueled buses, Renewable Hydrogen for the State of Hawaii program, New York state alternative transportation fuels program, Colorado program. 9 refs

10 CFR 490.203 - Light Duty Alternative Fueled Vehicle Plan.

Science.gov (United States)

2010-01-01

... Efficiency and Renewable Energy, EE-33, 1000 Independence Ave., SW., Washington, DC 20585, or to such other... 10 Energy 3 2010-01-01 2010-01-01 false Light Duty Alternative Fueled Vehicle Plan. 490.203 Section 490.203 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM...

Alternate-Fueled Combustor-Sector Performance: Part A: Combustor Performance Part B: Combustor Emissions

Science.gov (United States)

Shouse, D. T.; Neuroth, C.; Henricks, R. C.; Lynch, A.; Frayne, C.; Stutrud, J. S.; Corporan, E.; Hankins, T.

2010-01-01

Alternate aviation fuels for military or commercial use are required to satisfy MIL-DTL-83133F(2008) or ASTM D 7566 (2010) standards, respectively, and are classified as drop-in fuel replacements. To satisfy legacy issues, blends to 50% alternate fuel with petroleum fuels are certified individually on the basis of feedstock. Adherence to alternate fuels and fuel blends requires smart fueling systems or advanced fuel-flexible systems, including combustors and engines without significant sacrifice in performance or emissions requirements. This paper provides preliminary performance (Part A) and emissions and particulates (Part B) combustor sector data for synthetic-parafinic-kerosene- (SPK-) type fuel and blends with JP-8+100 relative to JP-8+100 as baseline fueling.

Implications of using alternate fuel cycles to meet Ontario's nuclear power demand

International Nuclear Information System (INIS)

Lau, J.H.K.

1978-08-01

The use of alternate fuel cycles to meet an assumed nuclear capacity growth rate in Ontario is examined. Two criteria are used: the ability of the alternate fuel cycles to lessen the uranium demand; and the ease of commercialization. The nuclear strategies considered assume the use of the natural uranium cycle and, starting in the year 2000, the gradual introduction of an alternate fuel cycle. The alternate fuel cycles reviewed are enriched uranium, mixed oxides, and a variety of thorium cycles. The cumulative uranium requirement to the year 2070, and the growth and size of the reprocessing and fuel fabrication industries are discussed in detail. Sensitivity analyses on nuclear capacity growth rate, recycling loss and delay time are also described. (auth)

Alternate-Fueled Combustor-Sector Performance—Part A: Combustor Performance and Part B: Combustor Emissions

OpenAIRE

Shouse, D. T.; Neuroth, C.; Hendricks, R. C.; Lynch, A.; Frayne, C. W.; Stutrud, J. S.; Corporan, E.; Hankins, Capt. T.

2012-01-01

Alternate aviation fuels for military or commercial use are required to satisfy MIL-DTL-83133F or ASTM D 7566 standards, respectively, and are classified as “drop-in’’ fuel replacements. To satisfy legacy issues, blends to 50% alternate fuel with petroleum fuels are acceptable. Adherence to alternate fuels and fuel blends requires “smart fueling systems’’ or advanced fuel-flexible systems, including combustors and engines, without significant sacrifice in performance or emissions requirements...

Solid Oxide Fuel Cells Operating on Alternative and Renewable Fuels

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiaoxing; Quan, Wenying; Xiao, Jing; Peduzzi, Emanuela; Fujii, Mamoru; Sun, Funxia; Shalaby, Cigdem; Li, Yan; Xie, Chao; Ma, Xiaoliang; Johnson, David; Lee, Jeong; Fedkin, Mark; LaBarbera, Mark; Das, Debanjan; Thompson, David; Lvov, Serguei; Song, Chunshan

2014-09-30

This DOE project at the Pennsylvania State University (Penn State) initially involved Siemens Energy, Inc. to (1) develop new fuel processing approaches for using selected alternative and renewable fuels – anaerobic digester gas (ADG) and commercial diesel fuel (with 15 ppm sulfur) – in solid oxide fuel cell (SOFC) power generation systems; and (2) conduct integrated fuel processor – SOFC system tests to evaluate the performance of the fuel processors and overall systems. Siemens Energy Inc. was to provide SOFC system to Penn State for testing. The Siemens work was carried out at Siemens Energy Inc. in Pittsburgh, PA. The unexpected restructuring in Siemens organization, however, led to the elimination of the Siemens Stationary Fuel Cell Division within the company. Unfortunately, this led to the Siemens subcontract with Penn State ending on September 23rd, 2010. SOFC system was never delivered to Penn State. With the assistance of NETL project manager, the Penn State team has since developed a collaborative research with Delphi as the new subcontractor and this work involved the testing of a stack of planar solid oxide fuel cells from Delphi.

Investing in Alternative Fuel Infrastructure: Insights for California from Stakeholder Interviews: Preprint

Energy Technology Data Exchange (ETDEWEB)

Melaina, Marc; Muratori, Matteo; McLaren, Joyce; Schwabe, Paul

2017-03-13

Increased interest in the use of alternative transportation fuels, such as natural gas, hydrogen, and electricity, is being driven by heightened concern about the climate impacts of gasoline and diesel emissions and our dependence on finite oil resources. A key barrier to widespread adoption of low- and zero-emission passenger vehicles is the availability of refueling infrastructure. Recalling the 'chicken and egg' conundrum, limited adoption of alternative fuel vehicles increases the perceived risk of investments in refueling infrastructure, while lack of refueling infrastructure inhibits vehicle adoption. In this paper, we present the results of a study of the perceived risks and barriers to investment in alternative fuels infrastructure, based on interviews with industry experts and stakeholders. We cover barriers to infrastructure development for three alternative fuels for passenger vehicles: compressed natural gas, hydrogen, and electricity. As an early-mover in zero emission passenger vehicles, California provides the early market experience necessary to map the alternative fuel infrastructure business space. Results and insights identified in this study can be used to inform investment decisions, formulate incentive programs, and guide deployment plans for alternative fueling infrastructure in the U.S. and elsewhere.

Alternative nuclear fuel cycles

International Nuclear Information System (INIS)

Till, C.E.

1979-01-01

This diffuse subject involves value judgments that are political as well as technical, and is best understood in that context. The four questions raised here, however, are mostly from the technical viewpoints: (1) what are alternative nuclear fuel cycles; (2) what generalizations are possible about their characteristics; (3) what are the major practical considerations; and (4) what is the present situation and what can be said about the outlook for the future

Alternative Fuels Data Center: James Madison University Teaches Alternative

Science.gov (United States)

Alternative Fuels Sept. 16, 2017 Photo of a truck Phoenix Utility Fleet Drives Smarter with Biodiesel Aug. 26 Cooking Oil Powers Biodiesel Vehicles in Rhode Island July 14, 2017 Photo of a truck Idaho Transports Mail Home Runs on Biodiesel in North Carolina June 9, 2017 Photo of a bus New Hampshire Cleans up with

Utilization of alternative fuels in diesel engines

Science.gov (United States)

Lestz, S. A.

1984-01-01

Performance and emission data are collected for various candidate alternate fuels and compare these data to that for a certified petroleum based number two Diesel fuel oil. Results for methanol, ethanol, four vegetable oils, two shale derived oils, and two coal derived oils are reported. Alcohol fumigation does not appear to be a practical method for utilizing low combustion quality fuels in a Diesel engine. Alcohol fumigation enhances the bioactivity of the emitted exhaust particles. While it is possible to inject many synthetic fuels using the engine stock injection system, wholly acceptable performance is only obtained from a fuel whose specifications closely approach those of a finished petroleum based Diesel oil. This is illustrated by the contrast between the poor performance of the unupgraded coal derived fuel blends and the very good performance of the fully refined shale derived fuel.

Development of alternative materials for BWR fuel springs

International Nuclear Information System (INIS)

Uruma, Y.; Osato, T.; Yamazaki, K.

2002-01-01

Major sources of radioactivity introduced into reactor water of BWR were estimated fuel crud and in-core materials (especially, fuel springs). Fuel springs are used for fixation of fuel cladding tubes with spacer grid. Those are small parts (total length is only within 25 mm) and so many numbers are loaded simultaneously and then total surfaces area are calculated up to about 200 m 2 . Fuel springs are located under high radiation field and high oxidative environment. Conventional fuel spring is made of alloy-X750 which is one of nickel-based alloy and is reported to show relatively higher corrosion release rate. 58 Co and 60 Co will be released directly into reactor water from intensely radio-activated fuel springs surface and increase radioactivity concentrations in primary coolant. Corrosion release control from fuel springs is an important technical item and a development of alternative material instead of alloy-X750 for fuel spring is a key subject to achieve ultra low man-rem exposure BWR plant. In present work, alloy-X718 which started usage for PWR fuel springs and stainless steel type 316L which has many mechanical property data are picked up for alternative materials and compared their corrosion behaviors with conventional material. Corrosion experiment was conducted under vapor-water two phases flow which is simulated fuel cladding surface boiling condition. After exposure, corrosion film formed under corrosion test was analyzed in detail and corrosion film amount and corrosion release amount are estimated among three materials. (authors)

Expectation dynamics: Ups and downs of alternative fuels

NARCIS (Netherlands)

Konrad, Kornelia Elke

2016-01-01

The transport sector must undergo radical changes if it is to reduce its carbon emissions, calling for alternative vehicles and fuel types. Researchers now analyse the expectation cycles for different fuel technologies and draw lessons for the role of US policy in supporting them.

Alternative Fuels Data Center: Washington Transportation Data for

Science.gov (United States)

stations in Washington with alternative fuels Fuel Public Private Biodiesel (B20 and above) 8 33 Compressed Partnerships Spark Biodiesel Success for Essential Baking Company Partnerships Spark Biodiesel Success for Videos on YouTube Video thumbnail for Seattle Bakery Delivers With Biodiesel Trucks Seattle Bakery

The use of thorium as an alternative nuclear fuel

International Nuclear Information System (INIS)

Wilson, D.J.

1982-04-01

The use of thorium as an alternative or supplementary nuclear fuel is examined and compared with uranium. A description of various reactor types and their suitability to thorium fuel, and a description of various aspects of the fuel cycle from mining to waste disposal, are included. Comments are made on the safety and economics of each aspect of the fuel cycle and the extension of the lifetime of nuclear fuel

Alternative jet fuel scenario analysis report

Science.gov (United States)

2012-11-30

This analysis presents a bottom up projection of the potential production of alternative aviation (jet) fuels in North America (United States, Canada, and Mexico) and the European Union in the next decade. The analysis is based on available pla...

Waste association in mass for coating formulations: a viable alternative to dispose

International Nuclear Information System (INIS)

Ferreira, E.A.C.; Soares Filho, J.E.; Souza, F.J.P.; Almeida, V.S. de; Oliveira, T.M. de

2016-01-01

The ceramic coatings industries are able to use in their formulations whose waste Eco disposal make the costly disposal, being able to reduce production costs by replacing traditional inputs for mining and industrial waste. Their raw materials are classified as plasticizers, fluxes and structural according to their physicochemical characteristics. Since waste falls within these classifications, their use in formulations becomes a viable and attractive alternative from an ecological point of view and marketing. Several studies have attested to waste incorporating viability porcelains formulations, however, is not common to find studies evaluating the addition of more than one simultaneously in formulations. It is the objective of the study, to examine whether fine waste rock and kaolin together with traditional raw materials are able to produce porcelain wet as technological properties defined by the NBR-13818. (author)

Overview of alternate-fuel fusion

International Nuclear Information System (INIS)

Miley, G.H.

1980-01-01

Alternate fuels (AFs) such as Cat-D, D- 3 He and p- 11 B offer the potential advantages of elimination of tritium breeding and reduced energy release in neutrons. An adequate energy balance appears exceedingly difficult to achieve with proton-based fuels such as p- 11 B. Thus Cat-D, which can ignite at temperatures in the range of 30 to 40 keV, represents the logical near-term candidate. An attractive variation which adds flexibility would be to develop semi-catalyzed-D plants for synfuel production with simultaneous generation of 3 He for use in D- 3 He satellite electrical power plants. These approaches and problems are discussed

Alternative Fuels Data Center: Hydrogen Related Links

Science.gov (United States)

marketing zero-emission proton exchange membrane (PEM) fuel cells for transportation and power generation production and use. Energy Management Institute The Energy Management Institute publishes the Alternative

77 FR 14482 - Petroleum Reduction and Alternative Fuel Consumption Requirements for Federal Fleets

Science.gov (United States)

2012-03-12

...-road or non-road vehicle. \\2\\ The definition of the term ``low-speed electric vehicle,'' as used... alternative fuel used in Federal fleet motor vehicles. This report also would include the alternative fuel...-- (1) a motor vehicle that operates solely on alternative fuel; or (2) a low-speed electric vehicle. (g...

Air quality effects of alternative fuels. Final report

Energy Technology Data Exchange (ETDEWEB)

Guthrie, P.; Ligocki, M.; Looker, R.; Cohen, J.

1997-11-01

To support the Alternative Fuels Utilization Program, a comparison of potential air quality effects of alternative transportation fuels is being performed. This report presents the results of Phase 1 of this program, focusing on reformulated gasoline (RFG), methanol blended with 15 percent gasoline (M85), and compressed natural gas (CNG). The fuels are compared in terms of effects on simulated future concentrations of ozone and mobile source air toxics in a photochemical grid model. The fuel comparisons were carried out for the future year 2020 and assumed complete replacement of gasoline in the projected light-duty gasoline fleet by each of the candidate fuels. The model simulations were carried out for the areas surrounding Los Angeles and Baltimore/DC, and other (non-mobile) sources of atmospheric emissions were projected according to published estimates of economic and population growth, and planned emission control measures specific to each modeling domain. The future-year results are compared to a future-year run with all gasoline vehicle emissions removed. The results of the comparison indicate that the use of M85 is likely to produce similar ozone and air toxics levels as those projected from the use of RFG. Substitution of CNG is projected to produce significantly lower levels of ozone and the mobile source air toxics than those projected for RFG or M85. The relative benefits of CNG substitution are consistent in both modeling domains. The projection methodologies used for the comparison are subject to a large uncertainty, and modeled concentration distributions depend on meteorological conditions. The quantitative comparison of fuel effects is thus likely to be sensitive to alternative assumptions. The consistency of the results for two very different modeling domains, using very different base assumptions, lends credibility to the qualitative differentiation among these fuels. 32 refs., 42 figs., 47 tabs.

Alternative Fuel Fleet Vehicle Evaluations | Transportation Research | NREL

Science.gov (United States)

delivery, transit, and freight vehicles. Although biodiesel is the most commonly used alternative fuel in Diesel and Biodiesel Renewable diesel is a conventional petroleum diesel substitute produced from alternative to conventional diesel and does not require any vehicle modifications. Biodiesel is an oxygenated

Biodiesel: An eco-friendly alternate fuel for the future: A review

Directory of Open Access Journals (Sweden)

Singaram Lakshmanan

2009-01-01

Full Text Available In today's society, researchers around the world are searching for ways to develop alternate forms of fuel. With the ever-rising fuel costs, developing alternate energy is a top priority. Biodiesel was developed to combat the high gas and oil prices. It is especially made for use in diesel cars and trucks. Biodiesel can be made from all natural foods that can produce oil. Oils such as vegetable, canola, peanut, rapeseed, palm, and olive oil can be used as bio diesel fuel. Virtually all oils that are used in the kitchens everyday can fuel automobiles. Biodiesel fuel is better for the environment because it burns cleaner and does not pollute the atmosphere. It is non-toxic and biodegradable, making it the perfect fuel. Many car manufacturers are realizing that the bio diesel automobile is becoming more popular, and are jumping on the bandwagon, by developing their own version of a biodiesel vehicle. They realize that the need for these vehicles will increase, and predict that they will be ready for the onslaught. Diesel engines have superior fuel efficiencies, and hence they are predominantly used in commercial transportation and agricultural machinery. Due to the shortage of diesel fuel and its increasing costs, a need for an alternate source of fuel for diesel engines is imminent. This paper investigates the suitability of biodiesels as such an alternative with particular reference to automobiles. It reviews techniques used to produce biodiesel and provides a comprehensive analysis of the benefits of using biodiesel over other fuels.

New options for conversion of vegetable oils to alternative fuels

Energy Technology Data Exchange (ETDEWEB)

Demirbas, A.; Kara, H. [Selcuk University, Konya (Turkey). Department of Chemical Engineering

2006-05-15

Biodiesel from transesterification of vegetable oils is an excellent alternative fuel. There is, however, a need to develop a direct process for conversion of vegetable oils into gasoline-competitive biodiesel and other petroleum products. Methyl esters of vegetable oils have several outstanding advantages among other new-renewable and clean engine fuel alternatives. The purpose of the transesterification process is to lower the viscosity of vegetable oil. Compared to No. 2 diesel fuel, all of the vegetable oils are much more viscous, whereas methyl esters of vegetable oils are slightly more viscous. The methyl esters are more volatile than those of the vegetable oils. Conversion of vegetable oils to useful fuels involves the pyrolysis and catalytic cracking of the oils into lower molecular products. Pyrolysis produces more biogasoline than biodiesel fuel. Soap pyrolysis products of vegetable oils can be used as alternative diesel engine fuel. The soaps obtained from the vegetable oils can be pyrolyzed into hydrocarbon-rich products. Zinc chloride catalyst contributed greatly to high amounts of hydrocarbons in the liquid product. The yield of ZnCl2 catalytic conversion of the soybean oil reached the maximum 79.9% at 660 K. (author)

Fundamental characterization of alternate fuel effects in continuous combustion systems

Energy Technology Data Exchange (ETDEWEB)

Blazowski, W.S.; Edelman, R.B.; Harsha, P.T.

1978-09-11

The overall objective of this contract is to assist in the development of fuel-flexible combustion systems for gas turbines as well as Rankine and Stirling cycle engines. The primary emphasis of the program is on liquid hydrocarbons produced from non-petroleum resouces. Fuel-flexible combustion systems will provide for more rapid transition of these alternate fuels into important future energy utilization centers (especially utility power generation with the combined cycle gas turbine). The specific technical objectives of the program are to develop an improved understanding of relationships between alternate fuel properties and continuous combustion system effects, and to provide analytical modeling/correlation capabilities to be used as design aids for development of fuel-tolerant combustion systems. Efforts this past year have been to evaluate experimental procedures for studying alternate fuel combustion effects and to determine current analytical capabilities for prediction of these effects. Jet Stirred Combustor studies during this period have produced new insights into soot formation in strongly backmixed systems and have provided much information for comparison with analytical predictions. The analytical effort included new applications of quasi-global modeling techniques as well as comparison of prediction with the experimental results generated.

Nuclear fuel: the thinking man's alternative

International Nuclear Information System (INIS)

Chamberlain, N.

1989-01-01

'Nuclear Fuel ' The Thinking Man's Alternative' is the title of the 55th Melchett Lecture given by Neville Chamberlain, Chief Executive of British Nuclear Fuels plc. This article is based on the address, the essence of which is that the case for nuclear power should be based upon an appreciation of the totality and sophistication of man's handling of his energy needs - not on a glib catch-phase or on a simple political dogma or on an economic argument. Arguments in favour of nuclear power were discussed. The conclusion was that nuclear energy is the thinking man's alternative because only thinking man could have and can develop it; secondly, only thinking men should be authorized to exploit and control it; thirdly, a thinking person will appreciate that, properly thought out and controlled, it must be the most important source of future energy for the benefit of mankind. (author)

Combustion of alternative fuels in vortex trapped combustor

International Nuclear Information System (INIS)

Ghenai, Chaouki; Zbeeb, Khaled; Janajreh, Isam

2013-01-01

Highlights: ► We model the combustion of alternative fuels in trapped vortex combustor (TVC). ► We test syngas and hydrogen/hydrocarbon mixture fuels. ► We examine the change in combustion performance and emissions of TVC combustor. ► Increasing the hydrogen content of the fuel will increase the temperature and NO x emissions. ► A high combustor efficiency is obtained for fuels with different compositions and LHV. - Abstract: Trapped vortex combustor represents an efficient and compact combustor for flame stability. Combustion stability is achieved through the use of cavities in which recirculation zones of hot products generated by the direct injection of fuel and air are created and acting as a continuous source of ignition for the incoming main fuel–air stream. Computational Fluid Dynamics analysis was performed in this study to test the combustion performance and emissions from the vortex trapped combustor when natural gas fuel (methane) is replaced with renewable and alternative fuels such as hydrogen and synthetic gas (syngas). The flame temperature, the flow field, and species concentrations inside the Vortex Trapped Combustor were obtained. The results show that hydrogen enriched hydrocarbon fuels combustion will result in more energy, higher temperature (14% increase when methane is replaced with hydrogen fuels) and NO x emissions, and lower CO 2 emissions (50% decrease when methane is replaced with methane/hydrogen mixture with 75% hydrogen fraction). The NO x emission increases when the fraction of hydrogen increases for methane/hydrogen fuel mixture. The results also show that the flame for methane combustion fuel is located in the primary vortex region but it is shifted to the secondary vortex region for hydrogen combustion.

Evaluation of alternative fuels for the Greek road transport sector using the analytic hierarchy process

International Nuclear Information System (INIS)

Tsita, Katerina G.; Pilavachi, Petros A.

2012-01-01

This paper evaluates alternative fuels for the Greek road transport sector, using the Analytic Hierarchy Process. Seven different alternatives of fuel mode are considered in this paper: internal combustion engine (ICE) and its combination with petroleum and 1st and 2nd generation biofuels blends, fuel cells, hybrid vehicles, plug-in hybrids and electric vehicles. The evaluation of alternative fuel modes is performed according to cost and policy aspects. In order to evaluate each alternative fuel, one base scenario and ten alternative scenarios with different weight factors selection per criterion are presented. After deciding the alternative fuels’ scoring against each criterion and the criteria weights, their synthesis gives the overall score and ranking for all ten alternative scenarios. It is concluded that ICE blended with 1st and 2nd generation biofuels are the most suitable alternative fuels for the Greek road transport sector. - Highlights: ► Alternative fuels for the Greek road transport sector have been evaluated. ► The method of the AHP was used. ► Seven different alternatives of fuel mode are considered. ► The evaluation is performed according to cost and policy aspects. ► The ICE with 1st and 2nd generation biofuels are the most suitable fuels.

Alternative concepts for spent fuel storage basin expansion at Morris Operation

International Nuclear Information System (INIS)

Graf, W.A. Jr.; King, C.E.; Miller, G.P.; Shadel, F.H.; Sloat, R.J.

1980-08-01

Alternative concepts for increasing basin capabilities for storage of spent fuel at the Morris Operation have been defined in a series of simplified flow diagrams and equipment schematics. Preliminary concepts have been outlined for (1) construction alternatives for an add-on basin, (2) high-density baskets for storage of fuel bundles or possible consolidated fuel rods in the existing or add-on basins, (3) modifications to the existing facility for increasing cask handling and fuel receiving capabilities and (4) accumulation, treatment and disposal of radwastes from storage operations. Preliminary capital and operating costs have been prepared and resource and schedule requirements for implementing the concepts have been estimated. The basin expansion alternatives would readily complement potential dry storage projects at the site in an integrated multi-stage program that could provide a total storage capacity of up to 7000 tonnes of spent fuel

Synthetic and Biomass Alternate Fueling in Aviation

Science.gov (United States)

Hendricks, R. C.; Bushnell, D. M.

2009-01-01

While transportation fueling can accommodate a broad range of alternate fuels, aviation fueling needs are specific, such as the fuel not freezing at altitude or become too viscous to flow properly or of low bulk energy density that shortens range. The fuel must also be compatible with legacy aircraft, some of which are more than 50 years old. Worldwide, the aviation industry alone uses some 85-95 billion gallons of hydrocarbon-based fossil fuel each year, which is about 10% of the transportation industry. US civil aviation alone consumes nearly 14 billion gallons. The enormity of the problem becomes overwhelming, and the aviation industry is taking alternate fueling issues very seriously. Biofuels (algae, cyanobacteria, halophytes, weeds that use wastelands, wastewater and seatwater), when properly sourced, have the capacity to be drop-in fuel replacements for petroleum fuels. As such, biojet from such sources solves the aviation CO2 emissions issue without the downsides of 'conventional' biofuels, such as competing with food and fresh water resources. Of the many current fundamental problems, the major biofuel problem is cost. Both research and development and creative engineering are required to reduce these biofuels costs. Research is also ongoing in several 'improvement' areas including refining/processing and biologics with greater disease resistance, greater bio-oil productivity, reduced water/nutrient requirements, etc. The authors' current research is aimed at aiding industry efforts in several areas. They are considering different modeling approaches, growth media and refining approaches, different biologic feedstocks, methods of sequestering carbon in the processes, fuel certification for aviation use and, overall, ensuring that biofuels are feasible from all aspects - operability, capacity, carbon cycle and financial. The authors are also providing common discussion grounds/opportunities for the various parties, disciplines and concerned organization to

Alternative Fuel and Advanced Technology Commercial Lawn Equipment (Brochure)

Energy Technology Data Exchange (ETDEWEB)

2014-10-01

The U.S. Department of Energy's Clean Cities program produced this guide to help inform the commercial mowing industry about product options and potential benefits. This guide provides information about equipment powered by propane, ethanol, compressed natural gas, biodiesel, and electricity, as well as advanced engine technology. In addition to providing an overview for organizations considering alternative fuel lawn equipment, this guide may also be helpful for organizations that want to consider using additional alternative fueled equipment.

DoD use of Domestically-Produced Alternative Fuels and Alternative Fuel Vehicles

Science.gov (United States)

2014-04-10

85 $21,927 Electric $171 Hydrogen $3 Liquefied Natural Gas (LNG) $4 Liquefied Petroleum Gas ( LPG ) $14 Total $25,053 Data source: GSA’s FAST Data...919 407 5,802 GAS PH 13 77 94 10 10 204 HYD DE 5 5 LNG BI 1 1 LPG BI 47 47 LPG DE 1 1 Conventional DSL DE 867 16,174 16,028 5,698 2,508 41,275...includes information on the status of: (1) use and potential use of domestically-produced alternative fuels including but not limited to, natural gas

Safeguards aspects for future fuel management alternatives

International Nuclear Information System (INIS)

Richter, B.; Stein, G.; Gerstler, R.

1987-01-01

In the future, more flexible fuel management strategies will be realized in light-water reactor power stations. The incentives for this development are based on considerations related to safe and economic plant operation, e.g. improved fuel strategies can save fuel resources and waste management efforts. A further important aspect of the nuclear fuel cycle deals with recycling strategies. At the back-end of the fuel cycle, the direct final disposal of spent fuel will have to be assessed as an alternative to recycling strategies. These major development fields will also have consequences for international safeguards. In particular, reactor fuel strategies may involve higher burn-up, conditioning of spent fuel directly in the power plant, gadolinium-poisoned fuel and different levels of enrichment. These strategies will have an impact on inspection activities, especially on the applicability of NDA techniques. The inspection frequency could also be affected in recycling strategies using MOX fuel. There may be problems with NDA methods if reprocessed feed is used in enrichment plants. On the other hand, the direct final disposal of spent fuel will raise safeguards problems regarding design verification, long-term safeguarding and the very feasibility of inaccessible nuclear material

Alternative Fuel News: Vol. 3, No. 4

Energy Technology Data Exchange (ETDEWEB)

NREL

2000-01-10

This final issue of the Alternative Fuel News (AFN) for the 20th century provides updates on specific Clean Cities Program progress and provide a glimpse of what is in store for the future. A national nonprofit organization has been part of the Clean Cities vision for some time, and now it is a reality as National Clean Cities, Inc. (NCC). While Clean Cities coalitions have had some success in securing local private foundation funds for alternative fuel vehicle (AFV) projects in their regions, now with the help of NCC, they can tap into the dollars available from large, national foundations. The Clean Cities Game Plan 2000, which is the highlight of the cover story, outlines the strategy for the next year.

Biofuels as an Alternative Energy Source for Aviation-A Survey

Science.gov (United States)

McDowellBomani, Bilal M.; Bulzan, Dan L.; Centeno-Gomez, Diana I.; Hendricks, Robert C.

2009-01-01

The use of biofuels has been gaining in popularity over the past few years because of their ability to reduce the dependence on fossil fuels. As a renewable energy source, biofuels can be a viable option for sustaining long-term energy needs if they are managed efficiently. We investigate past, present, and possible future biofuel alternatives currently being researched and applied around the world. More specifically, we investigate the use of ethanol, cellulosic ethanol, biodiesel (palm oil, algae, and halophytes), and synthetic fuel blends that can potentially be used as fuels for aviation and nonaerospace applications. We also investigate the processing of biomass via gasification, hydrolysis, and anaerobic digestion as a way to extract fuel oil from alternative biofuels sources.

Vermicomposting and anaerobic digestion – viable alternative options for terrestrial weed management – A review

Directory of Open Access Journals (Sweden)

Biswanath Saha

2018-03-01

Full Text Available The management of terrestrial weed is of great concern for the scientific community as these weeds cause adverse effect in different ecosystems like forest, agriculture and urban. The widespread of these weeds by their adaptive capability and morphological advancement is difficult to control. Parthenium hysterophorous, Lantana camara, Saccharum spontaneum, Ageratum conyzoides are the weeds that spread all over the world. There are various management practices employed for the control of this weeds. But all of these practices have some drawbacks those are neither environment friendly nor economical. In this paper a review has been done to evaluate various alternative management practices for these terrestrial weeds and to analyze their feasibility. Vermicomposting and anaerobic digestion can be viable alternative option which is cost effective as well. There are few studies regarding vermicomposting and anaerobic digestions of terrestrial weeds are done.

Life cycle models of conventional and alternative-fueled automobiles

Science.gov (United States)

Maclean, Heather Louise

This thesis reports life cycle inventories of internal combustion engine automobiles with feasible near term fuel/engine combinations. These combinations include unleaded gasoline, California Phase 2 Reformulated Gasoline, alcohol and gasoline blends (85 percent methanol or ethanol combined with 15 percent gasoline), and compressed natural gas in spark ignition direct and indirect injection engines. Additionally, I consider neat methanol and neat ethanol in spark ignition direct injection engines and diesel fuel in compression ignition direct and indirect injection engines. I investigate the potential of the above options to have a lower environmental impact than conventional gasoline-fueled automobiles, while still retaining comparable pricing and consumer benefits. More broadly, the objective is to assess whether the use of any of the alternative systems will help to lead to the goal of a more sustainable personal transportation system. The principal tool is the Economic Input-Output Life Cycle Analysis model which includes inventories of economic data, environmental discharges, and resource use. I develop a life cycle assessment framework to assemble the array of data generated by the model into three aggregate assessment parameters; economics, externalities, and vehicle attributes. The first step is to develop a set of 'comparable cars' with the alternative fuel/engine combinations, based on characteristics of a conventional 1998 gasoline-fueled Ford Taurus sedan, the baseline vehicle for the analyses. I calculate the assessment parameters assuming that these comparable cars can attain the potential thermal efficiencies estimated by experts for each fuel/engine combination. To a first approximation, there are no significant differences in the assessment parameters for the vehicle manufacture, service, fixed costs, and the end-of-life for any of the options. However, there are differences in the vehicle operation life cycle components and the state of technology

The history, genotoxicity and carcinogenicity of carbon-based fuels and their emissions: part 4 - alternative fuels.

Science.gov (United States)

Claxton, Larry D

2015-01-01

Much progress has been made in reducing the pollutants emitted from various combustors (including diesel engines and power plants) by the use of alternative fuels; however, much more progress is needed. Not only must researchers improve fuels and combustors, but also there is a need to improve the toxicology testing and analytical chemistry methods associated with these complex mixtures. Emissions from many alternative carbonaceous fuels are mutagenic and carcinogenic. Depending on their source and derivation, alternative carbonaceous fuels before combustion may or may not be genotoxic; however, in order to know their genotoxicity, appropriate chemical analysis and/or bioassay must be performed. Newly developed fuels and combustors must be tested to determine if they provide a public health advantage over existing technologies - including what tradeoffs can be expected (e.g., decreasing levels of PAHs versus increasing levels of NOx and possibly nitroarenes in ambient air). Another need is to improve exposure estimations which presently are a weak link in doing risk analyses. Copyright © 2014 Elsevier B.V. All rights reserved.

Alternative Fuels Data Center: Golden Eagle Delivers Beer With Natural Gas

Science.gov (United States)

Trucks Golden Eagle Delivers Beer With Natural Gas Trucks to someone by E-mail Share Alternative Fuels Data Center: Golden Eagle Delivers Beer With Natural Gas Trucks on Facebook Tweet about Alternative Fuels Data Center: Golden Eagle Delivers Beer With Natural Gas Trucks on Twitter Bookmark

Alternative Fuels Data Center: America's Largest Home Runs on Biodiesel in

Science.gov (United States)

North Carolina America's Largest Home Runs on Biodiesel in North Carolina to someone by E-mail Share Alternative Fuels Data Center: America's Largest Home Runs on Biodiesel in North Carolina on Facebook Tweet about Alternative Fuels Data Center: America's Largest Home Runs on Biodiesel in North

State and Alternative Fuel Provider Fleets Alternative Compliance; U.S. Department of Energy (DOE), Energy Efficiency & Renewable Energy (EERE)

Energy Technology Data Exchange (ETDEWEB)

None

2015-08-01

The final rule of the Energy Policy Act of 2005 and its associated regulations enable covered state and alternative fuel provider fleets to obtain waivers from the alternative fuel vehicle (AFV)-acquisition requirements of Standard Compliance. Under Alternative Compliance, covered fleets instead meet a petroleum-use reduction requirement. This guidance document is designed to help fleets better understand the Alternative Compliance option and successfully complete the waiver application process.

Novel approaches to the creation of alternative motor fuels from renewable raw materials

Directory of Open Access Journals (Sweden)

Ольга Олександрівна Гайдай

2016-06-01

Full Text Available The paper considers the method of obtaining aliphatic alcohols as components of alternative fuels by catalytic processing of synthesis gas under the conditions of mechanochemical activation of the catalyst without using high pressure.It is established that the introduction of hydrocarbon spherical clusters (onions in the alternative fuel changes physical, chemical and chemmotological characteristics of fuel due to the effect of structure formation. The results of comparative studies of the performance properties of hydrocarbon and alternative fuels are displayed

Alternative Fuel Vehicles: How Do They Really Measure Up?

Science.gov (United States)

similar to that of comparable gasoline vehicles. The publication is available in .pdf format through DOE's Alternative Fuels Data Center home page on the World Wide Web. For a hard copy, call the National Alternative

Test report : alternative fuels propulsion durability evaluation

Science.gov (United States)

2012-08-28

This document, prepared by Honeywell Aerospace, Phoenix, AZ (Honeywell), contains the final : test report (public version) for the U.S. Department of Transportation/Federal Aviation : Administration (USDOT/FAA) Alternative Fuels Propulsion Engine Dur...

Alternative Fuel News, Vol. 7, No. 3

Energy Technology Data Exchange (ETDEWEB)

2003-11-01

Quarterly magazine with articles on recent additions to the Clean Cities Alternative Fuel Station Locator database, biodiesel buying co-ops, and developing the CNG infrastructure in Bangladesh. Also a memo from CIVITAS 2003.

Alternative Fuels Data Center: St. Louis Airport Relies on Biodiesel and

Science.gov (United States)

Natural Gas Vehicles St. Louis Airport Relies on Biodiesel and Natural Gas Vehicles to someone by E-mail Share Alternative Fuels Data Center: St. Louis Airport Relies on Biodiesel and Natural Gas Vehicles on Facebook Tweet about Alternative Fuels Data Center: St. Louis Airport Relies on Biodiesel and

Alternative bio-based fuels for aviation: the clean airports program

International Nuclear Information System (INIS)

Shauck, M.E.; Zanin, M.G.

1997-01-01

The Renewable Aviation Fuels Development Center at Baylor University in Waco, Texas, has been designated as the national coordinator of the Clean Airports Program. The U.S. Dept. of Energy (US DOE) conferred this designation in March 1996. This program, a spin-off of the Clean Cities Program, was initiated to increase the use of alternative fuels in aviation. The two major fuels used in aviation are the current piston engine aviation gasoline and the current turbine engine fuel. The environmental impact of each of these fuels is significant. Aviation gasoline (100LL), currently used in the general aviation piston engine fleet, contributes 100% of the emissions containing lead in the U.S. today. Turbine engine fuel (jet fuel) produces two major environmental impacts: a local one, in the vicinity of the airports, and a global impact on climate change. The Clean Airports Program was established to achieve and maintain clean air at and in the vicinity of airports, through the use of alternative fuel-powered air and ground transportation vehicles. (author)

Well-to-wheels life-cycle analysis of alternative fuels and vehicle technologies in China

International Nuclear Information System (INIS)

Shen Wei; Han Weijian; Chock, David; Chai Qinhu; Zhang Aling

2012-01-01

A well-to-wheels life cycle analysis on total energy consumptions and greenhouse-gas (GHG) emissions for alternative fuels and accompanying vehicle technologies has been carried out for the base year 2010 and projected to 2020 based on data gathered and estimates developed for China. The fuels considered include gasoline, diesel, natural gas, liquid fuels from coal conversion, methanol, bio-ethanol and biodiesel, electricity and hydrogen. Use of liquid fuels including methanol and Fischer–Tropsch derived from coal will significantly increase GHG emissions relative to use of conventional gasoline. Use of starch-based bio-ethanol will incur a substantial carbon disbenefit because of the present highly inefficient agricultural practice and plant processing in China. Electrification of vehicles via hybrid electric, plug-in hybrid electric (PHEV) and battery electric vehicle technologies offers a progressively improved prospect for the reduction of energy consumption and GHG emission. However, the long-term carbon emission reduction is assured only when the needed electricity is generated by zero- or low-carbon sources, which means that carbon capture and storage is a necessity for fossil-based feedstocks. A PHEV that runs on zero- or low-carbon electricity and cellulosic ethanol may be one of the most attractive fuel-vehicle options in a carbon-constrained world. - Highlights: ► Data and estimates unique to China are used in this analysis. ► Use of starch-based bio-ethanol will incur a substantial carbon disbenefit in China. ► Use of methanol derived from coal will incur even more carbon disbenefit. ► Plug-in-hybrid with cellulosic ethanol and clean electricity may be a viable option.

Alternative Liquid Fuels Simulation Model (AltSim).

Energy Technology Data Exchange (ETDEWEB)

Williams, Ryan; Baker, Arnold Barry; Drennen, Thomas E.

2009-12-01

The Alternative Liquid Fuels Simulation Model (AltSim) is a high-level dynamic simulation model which calculates and compares the production and end use costs, greenhouse gas emissions, and energy balances of several alternative liquid transportation fuels. These fuels include: corn ethanol, cellulosic ethanol from various feedstocks (switchgrass, corn stover, forest residue, and farmed trees), biodiesel, and diesels derived from natural gas (gas to liquid, or GTL), coal (coal to liquid, or CTL), and coal with biomass (CBTL). AltSim allows for comprehensive sensitivity analyses on capital costs, operation and maintenance costs, renewable and fossil fuel feedstock costs, feedstock conversion ratio, financial assumptions, tax credits, CO{sub 2} taxes, and plant capacity factor. This paper summarizes the structure and methodology of AltSim, presents results, and provides a detailed sensitivity analysis. The Energy Independence and Security Act (EISA) of 2007 sets a goal for the increased use of biofuels in the U.S., ultimately reaching 36 billion gallons by 2022. AltSim's base case assumes EPA projected feedstock costs in 2022 (EPA, 2009). For the base case assumptions, AltSim estimates per gallon production costs for the five ethanol feedstocks (corn, switchgrass, corn stover, forest residue, and farmed trees) of $1.86, $2.32, $2.45, $1.52, and $1.91, respectively. The projected production cost of biodiesel is $1.81/gallon. The estimates for CTL without biomass range from $1.36 to $2.22. With biomass, the estimated costs increase, ranging from $2.19 per gallon for the CTL option with 8% biomass to $2.79 per gallon for the CTL option with 30% biomass and carbon capture and sequestration. AltSim compares the greenhouse gas emissions (GHG) associated with both the production and consumption of the various fuels. EISA allows fuels emitting 20% less greenhouse gases (GHG) than conventional gasoline and diesels to qualify as renewable fuels. This allows several of the

Decommissioning alternatives for the West Valley, New York, Fuel Reprocessing Plant

Energy Technology Data Exchange (ETDEWEB)

Munson, L F; Nemec, J F; Koochi, A K

1978-06-01

The methodology and numerical values of NUREG-0278 were applied to four decommissioning alternatives for the West Valley Fuel Reprocessing Plant. The cost and impacts of the following four alternatives for the process building, fuel receiving and storage, waste tank farm, and auxiliary facilities were assessed: (1) layaway, (2) protective storage, (3) preparation for alternate nuclear use, and (4) dismantlement. The estimated costs are 5.7, 11, 19, and 31 million dollars, respectively. (DLC)

Decommissioning alternatives for the West Valley, New York, Fuel Reprocessing Plant

International Nuclear Information System (INIS)

Munson, L.F.; Nemec, J.F.; Koochi, A.K.

1978-06-01

The methodology and numerical values of NUREG-0278 were applied to four decommissioning alternatives for the West Valley Fuel Reprocessing Plant. The cost and impacts of the following four alternatives for the process building, fuel receiving and storage, waste tank farm, and auxiliary facilities were assessed: (1) layaway, (2) protective storage, (3) preparation for alternate nuclear use, and (4) dismantlement. The estimated costs are 5.7, 11, 19, and 31 million dollars, respectively

Arizona Public Service - Alternative Fuel (Hydrogen) Pilot Plant Design Report

Energy Technology Data Exchange (ETDEWEB)

James E. Francfort

2003-12-01

Hydrogen has promise to be the fuel of the future. Its use as a chemical reagent and as a rocket propellant has grown to over eight million metric tons per year in the United States. Although use of hydrogen is abundant, it has not been used extensively as a transportation fuel. To assess the viability of hydrogen as a transportation fuel and the viability of producing hydrogen using off-peak electric energy, Pinnacle West Capital Corporation (PNW) and its electric utility subsidiary, Arizona Public Service (APS) designed, constructed, and operates a hydrogen and compressed natural gas fueling station—the APS Alternative Fuel Pilot Plant. This report summarizes the design of the APS Alternative Fuel Pilot Plant and presents lessons learned from its design and construction. Electric Transportation Applications prepared this report under contract to the U.S. Department of Energy’s Advanced Vehicle Testing Activity. The Idaho National Engineering and Environmental Laboratory manages these activities for the Advanced Vehicle Testing Activity.

Bio-fuels for the gas turbine: A review

International Nuclear Information System (INIS)

Gupta, K.K.; Rehman, A.; Sarviya, R.M.

2010-01-01

Due to depletion of fossil fuel, bio-fuels have generated a significant interest as an alternative fuel for the future. The use of bio-fuels to fuel gas turbine seems a viable solution for the problems of decreasing fossil-fuel reserves and environmental concerns. Bio-fuels are alternative fuels, made from renewable sources and having environmental benefit. In recent years, the desire for energy independence, foreseen depletion of nonrenewable fuel resources, fluctuating petroleum fuel costs, the necessity of stimulating agriculture based economy, and the reality of climate change have created an interest in the development of bio-fuels. The application of bio-fuels in automobiles and heating applications is increasing day by day. Therefore the use of these fuels in gas turbines would extend this application to aviation field. The impact of costly petroleum-based aviation fuel on the environment is harmful. So the development of alternative fuels in aviation is important and useful. The use of liquid and gaseous fuels from biomass will help to fulfill the Kyoto targets concerning global warming emissions. In addition, to reduce exhaust emission waste gases and syngas, etc., could be used as a potential gas turbine fuel. The term bio-fuel is referred to alternative fuel which is produced from biomass. Such fuels include bio-diesel, bio-ethanol, bio-methanol, pyrolysis oil, biogas, synthetic gas (dimethyl ether), hydrogen, etc. The bio-ethanol and bio-methanol are petrol additive/substitute. Bio-diesel is an environment friendly alternative liquid fuel for the diesel/aviation fuel. The gas turbine develops steady flame during its combustion; this feature gives a flexibility to use alternative fuels. Therefore so the use of different bio-fuels in gas turbine has been investigated by a good number of researchers. The suitability and modifications in the existing systems are also recommended. (author)

46 CFR 58.50-15 - Alternate material for construction of independent fuel tanks.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Alternate material for construction of independent fuel...) MARINE ENGINEERING MAIN AND AUXILIARY MACHINERY AND RELATED SYSTEMS Independent Fuel Tanks § 58.50-15 Alternate material for construction of independent fuel tanks. (a) Materials other than those specifically...

Assessment of the impacts of spent fuel disassembly alternatives on the Nuclear Waste Isolation System

International Nuclear Information System (INIS)

1984-07-01

The objective of this report was to evaluate four possible alternative methods of preparing and packaging spent fuel assemblies for geologic disposal against the Reference Process of unmodified spent fuel. The four alternative processes were: (1) End fitting removal, (2) Fission gas venting and resealing, (3) Fuel bundle disassembly and close packing of fuel pins, and (4) Fuel shearing and immobilization. Systems analysis was used to develop a basis of comparison of the alternatives. Conceptual processes and facility layouts were devised for each of the alternatives, based on technology deemed feasible for the purpose. Assessments were made of 15 principal attributes from the technical, operational, safety/risk, and economic considerations related to each of the alternatives, including both the surface packaging and underground repository operations. Specific attributes of the alternative processes were evaluated by assigning a number for each that expressed its merit relative to the corresponding attribute of the Reference Process. Each alternative process was then ranked by summing the numbers for attributes in each of the four assessment areas and collectively. Fuel bundle disassembly and close packing of fuel pins was ranked the preferred method of disposal of spent fuel. 63 references, 46 figures, 46 tables

Hydrogen as alternative clean fuel: Economic analysis

International Nuclear Information System (INIS)

Coiante, D.

1995-03-01

In analogy to biofuel production from biomasses, the electrolytic conversion of other renewable energies into hydrogen as an alternative clean fuel is considered. This solution allows the intermittent renewable energy sources, as photovoltaics and wind energy, to enhance their development and enlarge the role into conventional fuel market. A rough economic analysis of hydrogen production line shows the costs, added by electrolysis and storage stages, can be recovered by properly accounting for social and environmental costs due to whole cycle of conventional fuels, from production to use. So, in a perspective of attaining the economic competitiveness of renewable energy, the hydrogen, arising from intermittent renewable energy sources, will be able to compete in the energy market with conventional fuels, making sure that their substitution will occur in a significant amount and the corresponding environment

Alternative fuel properties of tall oil fatty acid methyl ester-diesel fuel blends

Energy Technology Data Exchange (ETDEWEB)

Altiparmak, D.; Keskin, A.; Koca, A. [Gazi University, Ankara (Turkey). Technical Education Faculty; Guru, M. [Gazi University, Ankara (Turkey). Engineering and Architectural Faculty

2007-01-15

In this experimental work, tall oil methyl ester-diesel fuel blends as alternative fuels for diesel engines were studied. Tall oil methyl ester was produced by reacting tall oil fatty acids with methyl alcohol under optimum conditions. The blends of tall oil methyl ester-diesel fuel were tested in a direct injection diesel engine at full load conditions. The effects of the new fuel blends on the engine performance and exhaust emission were tested. It was observed that the engine torque and power output with tall oil methyl ester-diesel fuel blends increased up to 6.1% and 5.9%, respectively. It was also seen that CO emissions decreased to 38.9% and NO{sub x} emissions increased up to 30% with the new fuel blends. The smoke capacity did not vary significantly. (author)

Alternative fuel properties of tall oil fatty acid methyl ester-diesel fuel blends.

Science.gov (United States)

Altiparmak, Duran; Keskin, Ali; Koca, Atilla; Gürü, Metin

2007-01-01

In this experimental work, tall oil methyl ester-diesel fuel blends as alternative fuels for diesel engines were studied. Tall oil methyl ester was produced by reacting tall oil fatty acids with methyl alcohol under optimum conditions. The blends of tall oil methyl ester-diesel fuel were tested in a direct injection diesel engine at full load condition. The effects of the new fuel blends on the engine performance and exhaust emission were tested. It was observed that the engine torque and power output with tall oil methyl ester-diesel fuel blends increased up to 6.1% and 5.9%, respectively. It was also seen that CO emissions decreased to 38.9% and NO(x) emissions increased up to 30% with the new fuel blends. The smoke opacity did not vary significantly.

Alternative Fuels Data Center: Fleet Application for School Transportation

Science.gov (United States)

Propane Buses Jan. 26, 2016 Video thumbnail for Biodiesel Offers an Easy Alternative for Fleets Biodiesel thumbnail for Biodiesel Fuels Education in Alabama Biodiesel Fuels Education in Alabama May 1, 2012 Video School Transportation Videos on YouTube Video thumbnail for New Hampshire Cleans up with Biodiesel Buses

Using of cotton oil soapstock biodiesel-diesel fuel blends as an alternative diesel fuel

Energy Technology Data Exchange (ETDEWEB)

Keskin, Ali [Technical Education Faculty, Mersin University, 33500 Mersin (Turkey); Guerue, Metin [Engineering and Architectural Faculty, Gazi University, 06570 Maltepe, Ankara (Turkey); Altiparmak, Duran [Technical Education Faculty, Gazi University, 06500 Ankara (Turkey); Aydin, Kadir [Engineering and Architectural Faculty, Cukurova University, 01330 Adana (Turkey)

2008-04-15

In this study, usability of cotton oil soapstock biodiesel-diesel fuel blends as an alternative fuel for diesel engines were studied. Biodiesel was produced by reacting cotton oil soapstock with methyl alcohol at determined optimum condition. The cotton oil biodiesel-diesel fuel blends were tested in a single cylinder direct injection diesel engine. Engine performances and smoke value were measured at full load condition. Torque and power output of the engine with cotton oil soapstock biodiesel-diesel fuel blends decreased by 5.8% and 6.2%, respectively. Specific fuel consumption of engine with cotton oil soapstock-diesel fuel blends increased up to 10.5%. At maximum torque speeds, smoke level of engine with blend fuels decreased up to 46.6%, depending on the amount of biodiesel. These results were compared with diesel fuel values. (author)

Using of cotton oil soapstock biodiesel-diesel fuel blends as an alternative diesel fuel

International Nuclear Information System (INIS)

Keskin, Ali; Guerue, Metin; Altiparmak, Duran; Aydin, Kadir

2008-01-01

In this study, usability of cotton oil soapstock biodiesel-diesel fuel blends as an alternative fuel for diesel engines were studied. Biodiesel was produced by reacting cotton oil soapstock with methyl alcohol at determined optimum condition. The cotton oil biodiesel-diesel fuel blends were tested in a single cylinder direct injection diesel engine. Engine performances and smoke value were measured at full load condition. Torque and power output of the engine with cotton oil soapstock biodiesel-diesel fuel blends decreased by 5.8% and 6.2%, respectively. Specific fuel consumption of engine with cotton oil soapstock-diesel fuel blends increased up to 10.5%. At maximum torque speeds, smoke level of engine with blend fuels decreased up to 46.6%, depending on the amount of biodiesel. These results were compared with diesel fuel values. (author)

Panorama 2009 - aviation and alternative fuels

International Nuclear Information System (INIS)

2008-01-01

Several key priorities have been targeted for development in the aviation industry: diversifying energy resources, keeping consumption levels under control and reducing polluting emissions to improve air quality. Like the road transport sector, the air transport sector is mounting a determined effort to reduce the level of its greenhouse gas emissions. Among the various solutions under consideration, alternative fuels are attracting particular attention. However, not all alternative solutions can be exploited, because of the constraints specific to the use of aircraft. A precise assessment should be made of all possible solutions to determine which ones should take preference

Public perception related to a hydrogen hybrid internal combustion engine transit bus demonstration and hydrogen fuel

International Nuclear Information System (INIS)

Hickson, Allister; Phillips, Al; Morales, Gene

2007-01-01

Hydrogen has been widely considered as a potentially viable alternative to fossil fuels for use in transportation. In addition to price competitiveness with fossil fuels, a key to its adoption will be public perceptions of hydrogen technologies and hydrogen fuel. This paper examines public perceptions of riders of a hydrogen hybrid internal combustion engine bus and hydrogen as a fuel source

Technical and economic feasibility of alternative fuel use in process heaters and small boilers

Energy Technology Data Exchange (ETDEWEB)

1980-02-01

The technical and economic feasibility of using alternate fuels - fuels other than oil and natural gas - in combustors not regulated by the Powerplant and Industrial Fuel Use Act of 1978 (FUA) was evaluated. FUA requires coal or alternate fuel use in most large new boilers and in some existing boilers. Section 747 of FUA authorizes a study of the potential for reduced oil and gas use in combustors not subject to the act: small industrial boilers with capacities less than 100 MMBtu/hr, and process heat applications. Alternative fuel use in combustors not regulated by FUA was examined and the impact of several measures to encourage the substitution of alternative fuels in these combustors was analyzed. The primary processes in which significant fuel savings can be achieved are identified. Since feedstock uses of oil and natural gas are considered raw materials, not fuels, feedstock applications are not examined in this analysis. The combustors evaluated in this study comprise approximately 45% of the fuel demand projected in 1990. These uses would account for more than 3.5 million barrels per day equivalent fuel demand in 1990.

Using Checklists to Assess Your Transition to Alternative Fuels: A Technical Reference

Energy Technology Data Exchange (ETDEWEB)

Risch, C. E. [Argonne National Lab. (ANL), Argonne, IL (United States); Santini, D. J. [Argonne National Lab. (ANL), Argonne, IL (United States); Johnson, L. R. [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-12-01

The Checklist for Transition to New Alternative Fuel(s) was published in September 2011 by Chuck Risch and Dan Santini. Many improvements, described below, have been incorporated into this current document, Checklists for Assessing the Transitions to New Highway Fuels.2 Further, the original authors and Larry Johnson, co-author of the current report, identified a need for a succinct version of the full report and prepared a brochure based on it to aid busy decisionmakers: Check It Out: Using Checklists to Assess Your Transition to Alternative Fuels.2 These checklists are tools for those stakeholders charged with determining a feasible alternative fuel or fuels for highway transportation systems of the future. The original had four major players whose needs had to be satisfied for a successful transition. The term “activist,” intended to encompass environmental and other special interests, was included in the “customers” category. Activists are customers of the government in the sense that they organize citizens to exert political pressure to regulate the design of vehicles, fuel infrastructure, and roadway networks. Many who evaluate alternative fuels view activists, particularly environmental activists, as a separate category. Further, “activist” has become a pejorative term to many people. Therefore, we have used the word “advocate” or “activist/advocate” instead. Thus, in this update we recognize that environmental and other activists/advocates have been--and will continue to be--a powerful force promoting change in the nature of the fuels that are used in transportation.

Impact of the use of alternative fuels on clinker reactivity

International Nuclear Information System (INIS)

Serrano-González, K.; Reyes-Valdez, A.; Chowaniec, O.

2017-01-01

The use of alternative fuels in the cement industry has increased its relevance in the past decades due to their ecological and economic benefits. In concert with the efforts to increase its use, several studies have focused on their potential impact with respect to clinker reactivity and how they could affect the expected physical and mechanical properties. This work studied the effects of five alternative fuels on the reactivity of eight industrial clinker samples, considering several analytical techniques. Differences were identified among the clinker samples after replacing the alternative fuels, mainly with simultaneous eliminations, as in samples S4, S5 and S8. The modifications were related to the polymorph, size and reactivity of tricalcium silicate and to the clinker profile during the hydration process, due to the SO3 consumption rate. These changes were expressed in the higher compressive strengths in comparison with the original reference clinker. [es

Alternative Fuels Data Center: Rhode Island Transportation Data for

Science.gov (United States)

stations in Rhode Island with alternative fuels Fuel Public Private Biodiesel (B20 and above) 3 3 More Rhode Island Videos on YouTube Video thumbnail for Cooking Oil Powers Biodiesel Vehicles in Rhode Island Cooking Oil Powers Biodiesel Vehicles in Rhode Island July 14, 2017 https://www.youtube.com/embed

Effect of Fuel Additives on Spray Performance of Alternative Jet Fuels

Science.gov (United States)

Kannaiyan, Kumaran; Sadr, Reza

2015-11-01

Role of alternative fuels on reducing the combustion pollutants is gaining momentum in both land and air transport. Recent studies have shown that addition of nanoscale metal particles as fuel additives to liquid fuels have a positive effect not only on their combustion performance but also in reducing the pollutant formation. However, most of those studies are still in the early stages of investigation with the addition of nanoparticles at low weight percentages. Such an addition can affect the hydrodynamic and thermo-physical properties of the fuel. In this study, the near nozzle spray performance of gas-to-liquid jet fuel with and without the addition of alumina nanoparticles are investigated at macro- and microscopic levels using optical diagnostic techniques. At macroscopic level, the addition of nanoparticles is seen to enhance the sheet breakup process when compared to that of the base fuel. Furthermore, the microscopic spray characteristics such as droplet size and velocity are also found to be affected. Although the addition of nanoscale metal particles at low weight percentages does not affect the bulk fluid properties, the atomization process is found to be affected in the near nozzle region. Funded by Qatar National Research Fund.

The DUPIC alternative for backend fuel cycle

International Nuclear Information System (INIS)

Lee, J.S.; Yang, M.S.; Park, H.S.; Boczar, P.; Sullivan, J.; Gadsby, R.D.

1997-01-01

The DUPIC fuel cycle was conceived as an alternative to the conventional fuel cycle backed options, with a view to multiple benefits expectable from burning spent PWR fuel again in CANDU reactors. It is based on the basic idea that the bulk of spent PWR fuel can be directly refabricated into a reusable fuel for CANDU of which high efficiency in neutron utilization would exhaustively burn the fissile remnants in the spent PWR fuel to a level below that of natural uranium. Such ''burn again'' strategy of the DUPIC fuel cycle implies that the spent PWR fuel will become CANDU fuel of higher burnup with relevant benefits such as spent PWR fuel disposition, saving of natural uranium fuel, etc. A salient feature of the DUPIC fuel cycle is neither the fissile content nor the bulk radioactivity is separated from the DUPIC mass flow which must be contained and shielded all along the cycle. This feature can be considered as a factor of proliferation resistance by deterrence against access to sensitive materials. It means also the requirement for remote systems technologies for DUPIC fuel operation. The conflicting aspects between better safeguardability and harder engineering problems of the radioactive fuel operation may be the important reason why the decades' old concept, since INFCE, of ''hot'' fuel cycle has not been pursued with much progress. In this context, the DUPIC fuel cycle could be a live example for development of proliferation resistant fuel cycle. As the DUPIC fuel cycle looks for synergism of fuel linkage from PWR to CANDU (or in broader sense LWR to HWR), Korea occupies a best position for DUPIC exercise with her unique strategy of reactor mix of both reactor types. But the DUPIC benefits can be extended to global bonus, expectable from successful development of the technology. (author)

Nuclear power a viable alternative in global warming context

International Nuclear Information System (INIS)

Cretu, Ileana; Balan, Iosif Bogdan; Ionila, Maria; Petra, Nicoleta Mihaela

2008-01-01

Energy sources available in the world include: coal, oil, gas, biomass, nuclear, hydroelectric, wind, solar, refuse-based, and hydrogen. In addition, fusion had been originally proposed as the long-term source. Every form of energy generation has both advantages and disadvantages. Burning fuel for energy requirements represent about 88% from the total emission of NO x and CO 2 , and about 90% from SO 2 respectively, and about 72% from suspension powder evacuated into the atmosphere. Global warming represents a real threat and is the most visible sign of the climatic changes which take place all over the world. To reduce the emission of greenhouse gases: carbon dioxide (CO 2 ), methane (CH 4 ), nitrous oxide (N 2 O), hydrofluorocarbons (HFCs), perfluorocarbons (PFCs), sulphur hexafluoride (SF 6 ), the 'Kyoto Protocol to the United Nations framework convention on climate change' has been adopted in 1997. According to this protocol European countries must reduce their overall emissions of greenhouse gases by at least 5% below 1990 levels in the commitment period 2008 -- 2012. In this context, because the natural resources for power generation based on the fossil fuels are decreasing and their prices are rising, nuclear power has become a real alternative for classical energy sources. It is indicated by: - Fuel is inexpensive because uranium represents a very small part of nuclear power cost and uranium sediment is found on a large scale all over the world; - No greenhouse emission or acid rain effects occur during a normal operation. Nuclear power is also named 'clean energy'; - Wastes are more compact than those of any source of energy and are stored in underground and secured deposits; - Nuclear energy has a number of advantages which warrant its use as one of the many methods of fulfilling the energy-demand of the world. Even with conservation efforts, energy demand increased and will continue to increase. Using each and every one of these forms of energy

Emissions from Petrol Engine Fueled Gasoline–Ethanol–Methanol (GEM Ternary mixture as Alternative Fuel

Directory of Open Access Journals (Sweden)

Thangavelu Saravana Kannan

2015-01-01

Full Text Available The increasing demands of petroleum fuels due to the rapid development automotive society coupled with the environmental pollution issues have inspired the efforts on exploring alternative fuels for internal combustion engines. Bioethanol obtained from biomass and bioenergy crops has been proclaimed as one of the feasible alternative to gasoline. In this study, the effect of gasoline–ethanol–methanol (GEM ternary blend on the emission characteristics of petrol engine was studied. Three different fuel blends, namely, E0 (gasoline, G75E21M4 (75% gasoline, 21% hydrous ethanol and 4% methanol and E25 (25% anhydrous ethanol and 75% gasoline were tested in a 1.3-l K3-VE spark-ignition engine. The results indicate that, when G75E21M4 fuel blend was used, a significant drop in CO, CO2, NOx and HC emissions by about 42%, 15%, 7% and 5.2% compared to E0, respectively. Moreover, the emission results for G75E21M4 are marginally lower than E25 whereas; HC emission was slightly higher than E25.

A numerical investigation on the influence of EGR in a supercharged SI engine fueled with gasoline and alternative fuels

International Nuclear Information System (INIS)

Mardi K, Mohsen; Khalilarya, Shahram; Nemati, Arash

2014-01-01

Highlights: • CFD modeling the combustion of different alternative fuels in SI engine. • 10% of EGR is the most desirable amount from the viewpoint of emissions and power. • EGR affects on methane fuel more than others. • Supercharging has the most noticeable effect on gasoline fuel and the least on hydrogen fuel. - Abstract: Alternative fuels are mostly extracted from renewable resources, and their emission levels can be lower than those of traditional fossil-based fuels. A computational fluid dynamics (CFD) method is utilized to investigate the effects of exhaust gas recirculation (EGR) and initial charge pressure on the emissions and performance of a SI engine. The engine is fueled separately by gasoline and some of potential alternative fuels including hydrogen, propane, methane, ethanol and methanol. The results of simulation are compared to the experimental data. In all validation cases, experimental and numerical results were observed to have good agreement with each other. The calculations are carried out for EGR ratios between 0% and 20% and four cases of initial pressure have been mentioned: P in = 1, 1.2, 1.4, 1.6 bar. The effect of EGR on NO x emission of methane is more than other fuels and its effect on IMEP of hydrogen is less than other fuels. From the viewpoints of emission and power, 10% of EGR seems to be the most desirable amount. The most noticeable effect of supercharging is on gasoline unlike hydrogen, which seems to be affected the least. The comparison of results shows that hydrogen due to its high heating value and burning without producing any carbon-based compounds such as HC, CO and CO 2 is an ideal alternative fuel compared to the other fuels

Efficiency versus cost of alternative fuels from renewable resources: outlining decision parameters

International Nuclear Information System (INIS)

Kaul, Sanjay; Edinger, Raphael

2004-01-01

In the discussion of traditional versus renewable energies and alternatives to conventional crude oil-based fuels in the transportation sector, efficiency calculations are but one decision making parameter. Comparing the assets and liabilities of fossil-based and renewable fuels in the transportation sector, further aspects such as centralized versus decentralized technologies, cost evaluations, taxation, and ecological/social benefits have to be taken into account. This paper outlines the driving parameters for shifting toward alternative fuels based on fossil or renewable resources and their use in innovative vehicle technologies such as advanced internal combustion and fuel cell electric drive systems. For the decision in favor or against an alternative fuel to be introduced to the mass market, automotive technologies and the energy supply system have to be examined in an integrated way. From an economic and technological perspective, some fuels may be even incompatible with the trend toward using renewable resources that have advantages in decentralized systems. Beyond efficiency calculations, political and industrial interests arise and may be influential to reshaping our currently crude oil-based mobility sector

Nuclear energy: the most viable alternative

International Nuclear Information System (INIS)

Guena, Ana Maria de Oliveira; Aquino, Afonso Rodrigues de

2006-01-01

In this article various forms of electric power generation considered clean are discussed. The paper approaches the nuclear, aeolian, solar and fuel cells, and a resume of the vantage and advantage of each one are discussed, emphasizing their impact on the environment

Alternative Fuel News: Official Publication of the Clean Cities Network and the Alternative Fuels Data Center, Vol. 6, No. 1

Energy Technology Data Exchange (ETDEWEB)

2002-07-01

Quarterly magazine with articles on auctions of used alternative fuel vehicles (AFVs), Royalty Enterprises of Ohio, and introducing AFVs in neglected urban areas. Plus Ford's new CNG school bus and electric buses in Connecticut.

IEA combustion agreement : a collaborative task on alternative fuels in combustion

International Nuclear Information System (INIS)

Larmi, M.

2009-01-01

The focus of the alternative fuels in combustion task of the International Energy Agency is on high efficiency engine combustion, furnace combustion, and combustion chemistry. The objectives of the task are to develop optimum combustion for dedicated fuels by fully utilizing the physical and chemical properties of synthetic and renewable fuels; a significant reduction in carbon dioxide, NOx and particulate matter emissions; determine the minimum emission levels for dedicated fuels; and meet future emission standards of engines without or with minimum after-treatment. This presentation discussed the alternative fuels task and addressed issues such as synthetic fuel properties and benefits. The anticipated future roadmap was presented along with a list of the synthetic and renewable engine fuels to be studied, such as neat oxygenates like alcohols and ethers, biogas/methane and gas combustion, fuel blends, dual fuel combustion, high cetane number diesel fuels like synthetic Fischer-Tropsch diesel fuel and hydrogenated vegetable oil, and low CN number fuels. Implementation examples were also discussed, such as fuel spray studies in optical spray bombs; combustion research in optical engines and combustion chambers; studies on reaction kinetics of combustion and emission formation; studies on fuel properties and ignition behaviour; combustion studies on research engines; combustion optimization; implementing the optimum combustion in research engines; and emission measurements. Overall milestone examples and the overall schedule of participating countries were also presented. figs.

A forecast of household ownership and use of alternative fuel vehicles: A multiple discrete-continuous choice approach

Energy Technology Data Exchange (ETDEWEB)

Ahn, Jiwoon [Korea Energy Economics Institute, Naeson 2-dong, Uiwang-si, Gyeonggi-do, 437-713 (Korea); Jeong, Gicheol [Technology Management, Economics and Policy Program, 37-402, College of Engineering, Seoul National University, San 56-1, Sillim-dong, Gwanak-gu, Seoul, 151-744 (Korea); Kim, Yeonbae [Technology Management, Economics and Policy Program, 37-318, College of Engineering, Seoul National University, San 56-1, Sillim-dong, Gwanak-gu, South Seoul, 151-744 (Korea)

2008-09-15

The paper analyzes how adding alternative fuel passenger cars to the market will affect patterns in demand for passenger cars. We use conjoint analysis and a multiple discrete-continuous choice model to estimate consumer preferences regarding alternative fuel vehicles, and based on the estimates we conduct a simulation to analyze changing rates of ownership and use of variously fueled passenger cars under the effect of the introduction of alternative fuel passenger cars. In addition, we estimate changes in overall fuel consumption and the emission of pollutants. The results show that gasoline-fueled cars will still be most consumers' first choice, but alternative fuel passenger cars will nevertheless compete and offer a substitute for the purchase and use of gasoline-fueled or diesel-fueled cars. Finally, results show that adding alternative fuel cars to the market would effectively lower gasoline and diesel fuel consumption and the emission of pollutants. (author)

A forecast of household ownership and use of alternative fuel vehicles: A multiple discrete-continuous choice approach

International Nuclear Information System (INIS)

Ahn, Jiwoon; Jeong, Gicheol; Kim, Yeonbae

2008-01-01

The paper analyzes how adding alternative fuel passenger cars to the market will affect patterns in demand for passenger cars. We use conjoint analysis and a multiple discrete-continuous choice model to estimate consumer preferences regarding alternative fuel vehicles, and based on the estimates we conduct a simulation to analyze changing rates of ownership and use of variously fueled passenger cars under the effect of the introduction of alternative fuel passenger cars. In addition, we estimate changes in overall fuel consumption and the emission of pollutants. The results show that gasoline-fueled cars will still be most consumers' first choice, but alternative fuel passenger cars will nevertheless compete and offer a substitute for the purchase and use of gasoline-fueled or diesel-fueled cars. Finally, results show that adding alternative fuel cars to the market would effectively lower gasoline and diesel fuel consumption and the emission of pollutants. (author)

Status and outlook for biofuels, other alternative fuels and new vehicles

Energy Technology Data Exchange (ETDEWEB)

Nylund, N -O; Aakko-Saksa, P; Sipilae, K

2008-03-15

The report presents an outlook for alternative motor fuels and new vehicles. The time period covered extends up to 2030. The International Energy Agency and the U.S. Energy Information Administration predict that the world energy demand will increase by over 50% from now to 2030, if policies remain unchanged. Most of the growth in demand for energy in general, as well as for transport fuels, will take place in non-OECD countries. Gasoline and diesel are projected to remain the dominant automotive fuels until 2030. Vehicle technology and high quality fuels will eventually solve the problem of harmful exhaust emissions. However, the problem with CO{sub 2} still remains, and much attention will be given to increase efficiency. Hybrid technology is one option to reduce fuel consumption. Diesel engines are fuel efficient, but have high emissions compared with advanced gasoline engines. New combustion systems combining the best qualities of gasoline and diesel engines promise low emissions as well as high efficiency. The scenarios for alternative fuels vary a lot. By 2030, alternative fuels could represent a 10- 30% share of transport fuels, depending on policies. Ambitious goals for biofuels in transport have been set. As advanced biofuels are still in their infancy, it seems probable that traditional biofuels will also be used in 2030. Ethanol is the fastest growing biofuel. Currently the sustainability of biofuels is discussed extensively. Synthetic fuels promise excellent end-use properties, reduced emissions, and if produced from biomass, also reduced CO{sub 2} emissions. The report presents an analysis of technology options to meet the requirements for energy security, reduced CO{sub 2} emissions, reduced local emissions as well as sustainability in general in the long run. In the short term, energy savings will be the main measure for CO{sub 2} reductions in transport, fuel switches will have a secondary role. (orig.)

Life-Cycle Analysis of Alternative Aviation Fuels in GREET

Energy Technology Data Exchange (ETDEWEB)

Elgowainy, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Han, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Wang, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Carter, N. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Stratton, R. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Hileman, J. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Malwitz, A. [Volpe National Transportation Systems Center, Cambridge, MA (United States); Balasubramanian, S. [Volpe National Transportation Systems Center, Cambridge, MA (United States)

2012-06-01

The Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model, developed at Argonne National Laboratory, has been expanded to include well-to-wake (WTWa) analysis of aviation fuels and aircraft. This report documents the key WTWa stages and assumptions for fuels that represent alternatives to petroleum jet fuel. The aviation module in GREET consists of three spreadsheets that present detailed characterizations of well-to-pump and pump-to-wake parameters and WTWa results. By using the expanded GREET version (GREET1_2011), we estimate WTWa results for energy use (total, fossil, and petroleum energy) and greenhouse gas (GHG) emissions (carbon dioxide, methane, and nitrous oxide) for (1) each unit of energy (lower heating value) consumed by the aircraft or(2) each unit of distance traveled/ payload carried by the aircraft. The fuel pathways considered in this analysis include petroleum-based jet fuel from conventional and unconventional sources (i.e., oil sands); Fisher-Tropsch (FT) jet fuel from natural gas, coal, and biomass; bio-jet fuel from fast pyrolysis of cellulosic biomass; and bio-jet fuel from vegetable and algal oils, which falls under the American Society for Testing and Materials category of hydroprocessed esters and fatty acids. For aircraft operation, we considered six passenger aircraft classes and four freight aircraft classes in this analysis. Our analysis revealed that, depending on the feedstock source, the fuel conversion technology, and the allocation or displacement credit methodology applied to co-products, alternative bio-jet fuel pathways have the potential to reduce life-cycle GHG emissions by 55–85 percent compared with conventional (petroleum-based) jet fuel. Although producing FT jet fuel from fossil feedstock sources — such as natural gas and coal — could greatly reduce dependence on crude oil, production from such sources (especially coal) produces greater WTWa GHG emissions compared with petroleum jet

Life-cycle analysis of alternative aviation fuels in GREET

Energy Technology Data Exchange (ETDEWEB)

Elgowainy, A.; Han, J.; Wang, M.; Carter, N.; Stratton, R.; Hileman, J.; Malwitz, A.; Balasubramanian, S. (Energy Systems)

2012-07-23

The Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model, developed at Argonne National Laboratory, has been expanded to include well-to-wake (WTWa) analysis of aviation fuels and aircraft. This report documents the key WTWa stages and assumptions for fuels that represent alternatives to petroleum jet fuel. The aviation module in GREET consists of three spreadsheets that present detailed characterizations of well-to-pump and pump-to-wake parameters and WTWa results. By using the expanded GREET version (GREET1{_}2011), we estimate WTWa results for energy use (total, fossil, and petroleum energy) and greenhouse gas (GHG) emissions (carbon dioxide, methane, and nitrous oxide) for (1) each unit of energy (lower heating value) consumed by the aircraft or (2) each unit of distance traveled/ payload carried by the aircraft. The fuel pathways considered in this analysis include petroleum-based jet fuel from conventional and unconventional sources (i.e., oil sands); Fisher-Tropsch (FT) jet fuel from natural gas, coal, and biomass; bio-jet fuel from fast pyrolysis of cellulosic biomass; and bio-jet fuel from vegetable and algal oils, which falls under the American Society for Testing and Materials category of hydroprocessed esters and fatty acids. For aircraft operation, we considered six passenger aircraft classes and four freight aircraft classes in this analysis. Our analysis revealed that, depending on the feedstock source, the fuel conversion technology, and the allocation or displacement credit methodology applied to co-products, alternative bio-jet fuel pathways have the potential to reduce life-cycle GHG emissions by 55-85 percent compared with conventional (petroleum-based) jet fuel. Although producing FT jet fuel from fossil feedstock sources - such as natural gas and coal - could greatly reduce dependence on crude oil, production from such sources (especially coal) produces greater WTWa GHG emissions compared with petroleum jet

Effects of alternative-fuel vehicles on air quality in Ontario, Canada

International Nuclear Information System (INIS)

Kantor, I.; Fowler, M.; Hajimiragha, A.; Canizares, C.; Elkamel, A.

2009-01-01

The economies of the developed world are increasingly including green technologies and processes that consider social, environmental and economic consequences. Hybrid electric vehicles and other fuel-efficient vehicle types can supply consumers with vehicles that decrease their ecological footprint and reduce the cost of fuel. However, one of the societal concerns often overlooked is the impact of alternative-fuel vehicle usage on the air quality in the urban environment. This paper presented a study that assessed the impact on air quality stemming from the operation of alternative fuel vehicles in urban environments. The study specifically focused on the province-wide emissions in Ontario and urban air pollution in the city of Toronto. The paper considered the life-cycle impacts of using alternative fuels for transportation purposes in terms of six major stressors for climate change, acidification and urban air quality. The two types of vehicles that were studied were plug-in hybrid electric vehicles (PHEVs) and fuel cell vehicles. Modeling of the penetration rates for both types of vehicles was completed based on the maximum capacity of the electrical grid including planned improvements. The scope of the study and discussion of health effects was first presented followed by data gathering and usage, methodology, results of supportable penetration and vehicle growth, and pollution abatement results. It was concluded that fuel cell vehicles have an advantage over, or near-equality with, PHEVs in almost every aspect of their emissions. 13 refs., 2 tabs., 10 figs

Commercializing an alternate transportation fuel: lessons learned from NGV

International Nuclear Information System (INIS)

Flynn, P.C.

2001-01-01

An alternate transportation fuel, compressed natural gas, was adopted in Canada in the mid-1980s due to the unique conditions present at the time. The factors that had an impact on the limited acceptance of the fuel, keeping its rate of adoption below the critical point were examined in this paper. It was revealed that a lack of infrastructure to support converted vehicles was the deciding factor. Existing refueling stations failed to become profitable, preventing further investment in refueling facilities and resulting in depressed sales of converted vehicles. Excessive parts markup by conversion dealers was another major hurdle, as was exaggerated claims for environmental and economic benefits. In addition, promotional programs were poorly designed. In the late 1980s, the relative values of oil and natural gas shifted, lowering the momentum from sales of conversions. The consequence was major players leaving the market and natural gas remained on the fringe in both Canada and the United States. Different alternate transportation fuels, including electricity and hydrogen, are being favored by new technologies and driving forces. The growth to commercial viability for those fuels will likely be influenced by some of the factors that played a role in the fate of natural gas as a transportation fuel. 4 refs., 1 fig

Tracking costs of alternatively fueled buses in Florida - phase II.

Science.gov (United States)

2013-04-01

The goal of this project is to continue collecting and reporting the data on the performance and costs of alternatively fueled public transit vehicles in the state in a consistent manner in order to keep the Bus Fuels Fleet Evaluation Tool (BuFFeT) c...

An economically viable alternative to coastal discharge of produced water

International Nuclear Information System (INIS)

D'Unger, C.V.; Carr, R.S.; Chapman, D.C.

1993-01-01

The discharge of produced waters to coastal estuaries has been common practice on the Texas coast for many years as these discharges are currently exempt from NPDES permitting. A study of the active produced water discharges in Nueces Bay, Texas revealed that all eight effluents were highly toxic as determined by the sea urchin (Arbacia punctulata) fertilization and embryological development assays. An alternative to discharging produced water into coastal estuaries is the use of disposal wells. Inactive wells can be converted to produced water disposal wells. Production records for the Nueces Bay, Texas area reveal that 52% of the gas wells produce less than 100 mcf/d and 50% of the oil wells produce less than 10 b/d. Using conservative estimates, the cost of converting an inactive well to a disposal well was calculated to be $31,500 which could be paid out by a gas well producing as little as 100 mcf/d in 26 months using only 50% of the well's profit. Combining multiple leases to a single disposal well would reduce proportionately the cost to each operation. This study has demonstrated that economically viable disposal options could be achieved in the Nueces Bay area through the imaginative and cooperative formation of produced water disposal ventures. This same model could be applied to produced water discharges in other coastal areas

Life cycle assessment of the use of alternative fuels in cement kilns: A case study.

Science.gov (United States)

Georgiopoulou, Martha; Lyberatos, Gerasimos

2018-06-15

The benefits of using alternative fuels (AFs) in the cement industry include reduction of the use of non-renewable fossil fuels and lower emissions of greenhouse gases, since fossil fuels are replaced with materials that would otherwise be degraded or incinerated with corresponding emissions and final residues. Furthermore, the use of alternative fuels maximizes the recovery of energy. Seven different scenaria were developed for the production of 1 ton of clinker in a rotary cement kiln. Each of these scenaria includes the use of alternative fuels such as RDF (Refuse derived fuel), TDF (Tire derived fuel) and BS (Biological sludge) or a mixture of them, in partial replacement of conventional fuels such as coal and pet coke. The purpose of this study is to evaluate the environmental impacts of the use of alternative fuels in relation to conventional fuels in the kiln operation. The Life Cycle Assessment (LCA) methodology is used to quantify the potential environmental impacts in each scenario. The interpretation of the results provides the conclusion that the most environmentally friendly prospect is the scenario based on RDF while the less preferable scenario is the scenario based on BS. Copyright © 2017 Elsevier Ltd. All rights reserved.

Baseline energy forecasts and analysis of alternative strategies for airline fuel conservation

Energy Technology Data Exchange (ETDEWEB)

1976-01-01

The objectives of this study were to identify measures to reduce airline fuel consumption and to evaluate the impact of these alternatives on fuel consumption through 1990. To evaluate the impact of fuel conservation strategies, baseline forecasts of airline activity and energy consumption to 1990 were developed. Alternative policy options to reduce fuel consumption were identified and analyzed for three baseline levels of aviation activity within the framework of an aviation activity/energy consumption model. By combining the identified policy options, a strategy was developed to provide incentives for airline fuel conservation. Strategies and policy options were evaluated in terms of their impact on airline fuel conservation and the functioning of the airline industry as well as the associated social, environmental, and economic costs. The need for strategies to conserve airline fuel is based on air transportation's dependence upon petroleum; the current lack of alternative energy sources; the potential for disruption of air service due to crises in fuel availability such as experienced during the OPEC oil embargo; and the overall national goal of energy independence through energy conservation in all consuming sectors. The transition from the current situation to that described by strategies and policy options may require difficult adjustments by the airline industry in the short term. In the long term, however, conservation strategies can enhance the health of the airline industry as well as its fuel efficiency.

Alternative Fuel Vehicles: What Do the Drivers Say?

Science.gov (United States)

survey of AFV fleet managers. Both the driver and the fleet manager reports are available in .pdf format through DOE's Alternative Fuels Data Center home page on the World Wide Web . For a hard copy, call the

76 FR 65382 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

Science.gov (United States)

2011-10-21

... Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline AGENCY: Environmental... gasoline. This final rule will provide flexibility to the regulated community by allowing an additional... Method for Olefins in Gasoline III. Statutory and Executive Order Reviews A. Executive Order 12866...

Tamanu oil. An alternative fuel for variable compression ratio engine

Energy Technology Data Exchange (ETDEWEB)

Raj, Mohan T. [SASTRA Univ., Thanjavur, Tamilnadu (India). Dept. of Mechanical Engineering; Kandasamy, Murugumohan Kumar K. [Pavendar Bharathidasan College of Engineering and Technology, Trichy, Tamilnadu (India). Dept. of Mechanical Engineering

2012-11-01

Biodiesel can be produced from vegetable oils and also from waste fats. Biodiesel is a monoalkyl- ester of long chain fatty acids derived from renewable feedstock such as vegetable oils by transesterification process. The esterified cotton seed oil, pungam oil, rice bran oil, and tamanu oil are chosen as the alternative fuels. Among these oils, tamanu oil is considered for the first time as an alternative fuel. An experiment is conducted to obtain the operating characteristics of the variable compression ratio (VCR) engine run by chosen esterified oils, and the results are compared with esterified tamanu oil. From the comparison of results, it is inferred that the engine performance is improved with significant reduction in emissions for the chosen oils without any engine modification. The effective compression ratio can be fixed based on the experimental results obtained in the engine since the findings of the present research work infer that the biodiesel obtained from tamanu oil is a promising alternative fuel for direct-injection four-stroke VCR engine. (orig.)

Toxic emissions from mobile sources: a total fuel-cycle analysis for conventional and alternative fuel vehicles.

Science.gov (United States)

Winebrake, J J; Wang, M Q; He, D

2001-07-01

Mobile sources are among the largest contributors of four hazardous air pollutants--benzene, 1,3-butadiene, acetaldehyde, and formaldehyde--in urban areas. At the same time, federal and state governments are promoting the use of alternative fuel vehicles as a means to curb local air pollution. As yet, the impact of this movement toward alternative fuels with respect to toxic emissions has not been well studied. The purpose of this paper is to compare toxic emissions from vehicles operating on a variety of fuels, including reformulated gasoline (RFG), natural gas, ethanol, methanol, liquid petroleum gas (LPG), and electricity. This study uses a version of Argonne National Laboratory's Greenhouse Gas, Regulated Emissions, and Energy Use in Transportation (GREET) model, appropriately modified to estimate toxic emissions. The GREET model conducts a total fuel-cycle analysis that calculates emissions from both downstream (e.g., operation of the vehicle) and upstream (e.g., fuel production and distribution) stages of the fuel cycle. We find that almost all of the fuels studied reduce 1,3-butadiene emissions compared with conventional gasoline (CG). However, the use of ethanol in E85 (fuel made with 85% ethanol) or RFG leads to increased acetaldehyde emissions, and the use of methanol, ethanol, and compressed natural gas (CNG) may result in increased formaldehyde emissions. When the modeling results for the four air toxics are considered together with their cancer risk factors, all the fuels and vehicle technologies show air toxic emission reduction benefits.

Alternative fuels: a Brazilian outlook

International Nuclear Information System (INIS)

Moreira, J.R.; Serra, G.E.

1990-01-01

This paper focuses on studies and information related to the use of alternative fuels in Brazil. The first part of this paper deals with the economics of different biomass technologies. The analysis consists of a careful costing of all operations involved. The study deals with wood, sugar cane and cassava, since these crops are exploited for commercial purposes in Brazil. Corn, although a useful raw material for producing ethanol in the United States, is not used for this purpose in Brazil. The second part deals with the industrial technologies used to convert biomass into energy. We consider several forms of energy derived from biomass and evaluate the economics of the processes. When opportune, we compare costs with those of the North American market. Market analysis and displacement of conventional energy are the subject of the third part of the paper. While the cost of each product is evaluated in most cases; in others the current market price is used. Finally, we raise the issues of institutional problems and planning and offer some conclusions on the future of biomass as an alternative energy source. The technological discussion in this paper is based on the Brazilian experience in producing ethanol and other fuels from biomass. It is possible to extrapolate the Brazilian experience to other developing countries. The observations made in this chapter are based on the conditions prevalent in the Brazilian south-central agricultural region, specifically the state of Sao Paulo. (author). 91 refs., 16 figs., 11 tabs

Taking an Alternative Route: A guide for fleet operators and individual owners using alternative fuels in cars and trucks

International Nuclear Information System (INIS)

LaRocque, T.

2001-01-01

Taking an Alternative Route is a 30-page guide for fleet managers and individual owners on using alternative fuels in cars and trucks. Discussed in detail are all fuels authorized for federal credits under the Energy Policy Act of 1992 (EPAct). The publication informs federal and state fleet managers about how to comply with EPAct, and provides information about the Clean Air Act Amendments

The comparison of alternatives for nuclear spent fuel management using multi-attribute utility function

International Nuclear Information System (INIS)

Yang, J. W.; Kang, C. S.

1999-01-01

It is necessary to find a solution immediately to nuclear spent fuel management that is temporarily stored in on-site spent fuel storage before the saturation of the storage. However the choice of alternative for nuclear spent fuel management consists of complex process that are affected by economic, technical and social factors. And it is not easy to quantify these factors; public opinion, probability of diplomatic problem and contribution to development of nuclear technology. Therefore the analysis of the affecting factors and assessment of alternatives are required. This study performed the comparison of the alternatives for nuclear spent fuel management using MAU (Multi-Attribute Utility Function) and AHP(Analytic Hierarchy Process)

Alternative nuclear fuel cycle arrangements for proliferation resistance: an overview of regulatory factors

International Nuclear Information System (INIS)

O'Brien, J.N.

1982-08-01

President Carter proposed the International Fuel Cycle Evaluation to analyze various alternative fuel cycles which could minimize the risk of nuclear weapons proliferation. DOE also initiated the Non-Proliferation Alternative Systems Assessment Program. In response to GAO contentions that NRC was not sufficiently involved in these two assessments, a NRC study was initiated, with emphasis on legal and institutional factors. Objectives were to examine multinational fuel cycle facilities, potential effects on the US/IAEA agreement, development of an algorithm for ranking potential fuel cycles, and potential licensing of candidate fuel cycles. This anthology represents the products of this study which has been conducted between 1979 and 1981

Simulation-Based Analysis of the Potential of Alternative Fuels towards Reducing CO2 Emissions from Aviation

Directory of Open Access Journals (Sweden)

Karsten Kieckhäfer

2018-01-01

Full Text Available The mid-term framework of global aviation is shaped by air travel demand growth rates of 2–5% p.a. and ambitious targets to reduce aviation-related CO2 emissions by up to 50% until 2050. Alternative jet fuels such as bio- or electrofuels can be considered as a potential means towards low-emission aviation. While these fuels offer significant emission reduction potential, their market success depends on manifold influencing factors like the maturity of the production technology or the development of the price of conventional jet fuel. To study the potential for adoption of alternative jet fuels in aviation and the extent to which alternative fuels can contribute to the reduction targets, we deploy a System Dynamics approach. The results indicate that the adoption of alternative fuels and therefore their potential towards low-emissions aviation is rather limited in most scenarios considered since current production processes do not allow for competitive prices compared to conventional jet fuel. This calls for the development of new production processes that allow for economic feasibility of converting biomass or hydrogen into drop-in fuels as well as political measures to promote the adoption of alternative fuels.

Sweet Sorghum Alternative Fuel and Feed Pilot Project

Energy Technology Data Exchange (ETDEWEB)

Slack, Donald C. [Univ. of Arizona, Tucson, AZ (United States). Agricultural and Biosystems Engineering Dept.; Kaltenbach, C. Colin [Univ. of Arizona, Tucson, AZ (United States)

2013-07-30

The University of Arizona undertook a “pilot” project to grow sweet sorghum on a field scale (rather than a plot scale), produce juice from the sweet sorghum, deliver the juice to a bio-refinery and process it to fuel-grade ethanol. We also evaluated the bagasse for suitability as a livestock feed and as a fuel. In addition to these objectives we evaluated methods of juice preservation, ligno-cellulosic conversion of the bagasse to fermentable sugars and alternative methods of juice extraction.

Utilization of waste cooking oil as an alternative fuel for Turkey.

Science.gov (United States)

Arslan, Ridvan; Ulusoy, Yahya

2017-04-03

This study is based on three essential considerations concerning biodiesel obtained from waste cooking oil: diesel engine emissions of biodiesel produced from waste cooking oil, its potential in Turkey, and policies of the Turkish government about environmentally friendly alternative fuels. Emission tests have been realized with 35.8 kW, four-cylinder, four-stroke, direct injection diesel tractor engine. Test results are compared with Euro non-road emission standards for diesel fuel and five different blends of biodiesel production from waste cooking oil. The results of the experimental study show that the best blends are B10 and B20 as they show the lowest emission level. The other dimensions of the study include potential analysis of waste cooking oil as diesel fuels, referring to fuel price policies applied in the past, and proposed future policies about the same issues. It was also outlined some conclusions and recommendations in connection with recycling of waste oils as alternative fuels.

A Choice Experiment on Alternative Fuel Vehicle Preferences of Private Car Owners in the Netherlands

NARCIS (Netherlands)

Hoen, A.; Koetse, M.J.

2014-01-01

This paper presents results of an online stated choice experiment on preferences of Dutch private car owners for alternative fuel vehicles (AFVs) and their characteristics. Results show that negative preferences for alternative fuel vehicles are large, especially for the electric and fuel cell car,

Tracking costs of alternatively fueled buses in Florida.

Science.gov (United States)

2011-11-04

The goal of the current project is to establish a recording and reporting mechanism for collecting field data on the performance and costs of alternatively fueled public transit vehicles operating in Florida in order to assist policy makers with thei...

Ongoing evaluation of alternatively fueled buses : final report.

Science.gov (United States)

2016-05-01

The goal of this project is to continue collecting and reporting data on the performance and costs of alternatively fueled public transit vehicles in Florida in a consistent manner. Over the course of this project, researchers sent repeated data requ...

Thermodynamic comparison and efficiency enhancement mechanism of coal to alternative fuel systems

International Nuclear Information System (INIS)

Ji, Xiaozhou; Li, Sheng; Gao, Lin; Jin, Hongguang

2016-01-01

Highlights: • Energy and exergy analysis are presented to three coal-to-alternative-fuels systems. • Internal reasons for performance differences for different systems are disclosed. • The temperature and heat release of synthesis reactions are key to plant efficiency. • The distillation unit and purge gas recovery are important to efficiency enhancement. - Abstract: Coal to alternative fuels is an important path to enforce energy security and to provide clean energy. In this paper, we use exergy analysis and energy utilization diagram (EUD) methods to disclose the internal reasons for performance differences in typical coal to alternative fuel processes. ASPEN plus software is used to simulate the coal-based energy systems, and the simulation results are verified with engineering data. Results show that coal to substitute natural gas (SNG) process has a higher exergy efficiency of 56.56%, while the exergy efficiency of traditional coal to methanol process is 48.65%. It is indicated that three key factors impact the performance enhancement of coal to alternative fuel process: (1) whether the fuel is distillated, (2) the synthesis temperature and the amount of heat release from reactions, and (3) whether the chemical purge gases from synthesis and distillation units are recovered. Distillation unit is not recommended and synthesis at high temperature and with large heat release is preferable for coal to alternative fuel systems. Gasification is identified as the main source of exergy destruction, and thereby how to decrease its destruction is the key direction of plant efficiency improvement in the future. Also, decreasing the power consumption in air separation unit by seeking for advanced technologies, i.e. membrane, or using another kind of oxidant is another direction to improve plant performance.

Refueling availability for alternative fuel vehicle markets: Sufficient urban station coverage

International Nuclear Information System (INIS)

Melaina, Marc; Bremson, Joel

2008-01-01

Alternative fuel vehicles can play an important role in addressing the challenges of climate change, energy security, urban air pollution and the continued growth in demand for transportation services. The successful commercialization of alternative fuels for vehicles is contingent upon a number of factors, including vehicle cost and performance. Among fuel infrastructure issues, adequate refueling availability is one of the most fundamental to successful commercialization. A commonly cited source reports 164,300 refueling stations in operation nationwide. However, from the perspective of refueling availability, this nationwide count tends to overstate the number of stations required to support the widespread deployment of alternative fuel vehicles. In terms of spatial distribution, the existing gasoline station networks in many urban areas are more than sufficient. We characterize a sufficient level of urban coverage based upon a subset of cities served by relatively low-density station networks, and estimate that some 51,000 urban stations would be required to provide this sufficient level of coverage to all major urban areas, 33 percent less than our estimate of total urban stations. This improved characterization will be useful for engineering, economic and policy analyses. (author)

Alternative Fuels and Advanced Vehicles: Resources for Fleet Managers (Clean Cities) (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Brennan, A.

2011-04-01

A discussion of the tools and resources on the Clean Cities, Alternative Fuels and Advanced Vehicles Data Center, and the FuelEconomy.gov Web sites that can help vehicle fleet managers make informed decisions about implementing strategies to reduce gasoline and diesel fuel use.

Greenfield Alternative Study LEU-Mo Fuel Fabrication Facility

Energy Technology Data Exchange (ETDEWEB)

Washington Division of URS

2008-07-01

This report provides the initial “first look” of the design of the Greenfield Alternative of the Fuel Fabrication Capability (FFC); a facility to be built at a Greenfield DOE National Laboratory site. The FFC is designed to fabricate LEU-Mo monolithic fuel for the 5 US High Performance Research Reactors (HPRRs). This report provides a pre-conceptual design of the site, facility, process and equipment systems of the FFC; along with a preliminary hazards evaluation, risk assessment as well as the ROM cost and schedule estimate.

DEVELOPMENT OF ALTERNATIVE FUELS AND CHEMICALS FROM SYNTHESIS GAS

Energy Technology Data Exchange (ETDEWEB)

Peter J. Tijrn

2003-05-31

This Final Report for Cooperative Agreement No. DE-FC22-95PC93052, the ''Development of Alternative Fuels and Chemicals from Synthesis Gas,'' was prepared by Air Products and Chemicals, Inc. (Air Products), and covers activities from 29 December 1994 through 31 July 2002. The overall objectives of this program were to investigate potential technologies for the conversion of synthesis gas (syngas), a mixture primarily of hydrogen (H{sub 2}) and carbon monoxide (CO), to oxygenated and hydrocarbon fuels and industrial chemicals, and to demonstrate the most promising technologies at the LaPorte, Texas Alternative Fuels Development Unit (AFDU). Laboratory work was performed by Air Products and a variety of subcontractors, and focused on the study of the kinetics of production of methanol and dimethyl ether (DME) from syngas, the production of DME using the Liquid Phase Dimethyl Ether (LPDME{trademark}) Process, the conversion of DME to fuels and chemicals, and the production of other higher value products from syngas. Four operating campaigns were performed at the AFDU during the performance period. Tests of the Liquid Phase Methanol (LPMEOH{trademark}) Process and the LPDME{trademark} Process were made to confirm results from the laboratory program and to allow for the study of the hydrodynamics of the slurry bubble column reactor (SBCR) at a significant engineering scale. Two campaigns demonstrated the conversion of syngas to hydrocarbon products via the slurry-phase Fischer-Tropsch (F-T) process. Other topics that were studied within this program include the economics of production of methyl tert-butyl ether (MTBE), the identification of trace components in coal-derived syngas and the means to economically remove these species, and the study of systems for separation of wax from catalyst in the F-T process. The work performed under this Cooperative Agreement has continued to promote the development of technologies that use clean syngas produced

Alternative Fuels Data Center: Codes and Standards Resources

Science.gov (United States)

resources linked below help project developers and code officials prepare and review code-compliant projects , storage, and infrastructure. The following charts show the SDOs responsible for these alternative fuel codes and standards. Biodiesel Vehicle and Infrastructure Codes and Standards Chart Electric Vehicle and

State of the Art on Alternative Fuels in Aviation. Executive summary

NARCIS (Netherlands)

Blakey, S.; Novelli, P.; Costes, P.; Bringtown, S.; Christensen, D.; Sakintuna, B.; Peineke, C.; Jongschaap, R.E.E.; Conijn, J.G.; Rutgers, B.; Valot, L.; Joubert, E.; Perelgritz, J.F.; Filogonio, A.; Roetger, T.; Prieur, A.; Starck, L.; Jeuland, N.; Bogers, P.; Midgley, R.; Bauldreay, J.; Rollin, G.; Rye, L.; Wilson, C.

2010-01-01

This paper summarises the findings from the SWAFEA preliminary state of the art study. It covers trends in aspects of future air transport, potential candidate fuels and associated feedstock along with sustainability and economical issues relevant for alternative fuels in aviation..

Health effects attributable to coal and nuclear fuel cycle alternatives

International Nuclear Information System (INIS)

Gotchy, R.L.

1977-09-01

Estimates of mortality and morbidity are presented based on present-day knowledge of health effects resulting from current component designs and operations of the fuel cycles, and anticipated emission rates and occupational exposure for the various fuel cycle facilities expected to go into operation in approximately the 1975-1985 period. It was concluded that, although there are large uncertainties in the estimates of potential health effects, the coal fuel cycle alternative has a greater health impact on man than the uranium fuel cycle. However, the increased risk of health effects for either fuel cycle represents a very small incremental risk to the average individual in the public

Alternatives for managing wastes from reactors and post-fission operations in the LWR fuel cycle. Volume 1. Summary: alternatives for the back of the LWR fuel cycle types and properties of LWR fuel cycle wastes projections of waste quantities; selected glossary

International Nuclear Information System (INIS)

1976-05-01

Volume I of the five-volume report contains executive and technical summaries of the entire report, background information of the LWR fuel cycle alternatives, descriptions of waste types, and projections of waste quantities. Overview characterizations of alternative LWR fuel cycle modes are also included

Final Technical Report for Alternative Fuel Source Study-An Energy Efficient and Environmentally Friendly Approach

Energy Technology Data Exchange (ETDEWEB)

Zee, Ralph [Auburn University, AL (United States); Schindler, Anton [Auburn University, AL (United States); Duke, Steve [Auburn University, AL (United States); Burch, Thom [Auburn University, AL (United States); Bransby, David [Auburn University, AL (United States); Stafford, Don [Lafarge North America, Inc., Alpharetta, GA (United States)

2010-08-31

The objective of this project is to conduct research to determine the feasibility of using alternate fuel sources for the production of cement. Successful completion of this project will also be beneficial to other commercial processes that are highly energy intensive. During this report period, we have completed all the subtasks in the preliminary survey. Literature searches focused on the types of alternative fuels currently used in the cement industry around the world. Information was obtained on the effects of particular alternative fuels on the clinker/cement product and on cement plant emissions. Federal regulations involving use of waste fuels were examined. Information was also obtained about the trace elements likely to be found in alternative fuels, coal, and raw feeds, as well as the effects of various trace elements introduced into system at the feed or fuel stage on the kiln process, the clinker/cement product, and concrete made from the cement. The experimental part of this project involves the feasibility of a variety of alternative materials mainly commercial wastes to substitute for coal in an industrial cement kiln in Lafarge NA and validation of the experimental results with energy conversion consideration.

49 CFR 536.10 - Treatment of dual-fuel and alternative fuel vehicles-consistency with 49 CFR part 538.

Science.gov (United States)

2010-10-01

... vehicles-consistency with 49 CFR part 538. 536.10 Section 536.10 Transportation Other Regulations Relating... vehicles—consistency with 49 CFR part 538. (a) Statutory alternative fuel and dual-fuel vehicle fuel... economy in a particular compliance category by more than the limits set forth in 49 U.S.C. 32906(a), the...

Sulfide Production and Corrosion in Seawater During Exposure to FAME Alternative Fuel

Science.gov (United States)

2012-06-01

transporting fatty acid methyl ester ( FAME ] alternative diesel fuel in contact with natural seawater under anaerobic conditions. Coastal Key West...Glycerol Fatty Acid Methyl Ester Exposure Chamber Anaerobic Chamber - bal. N2,10% H2, 0.1% C02 - maintain pH ~8 Polarization Resistance (Rp...and Corrosion in Seawater During Exposure to FAME Alternative Fuel Jason 5. Lee Richard I. Ray BrendaJ. Little Naval Research Laboratory Stennis

Production of jet fuel from alternative source

Energy Technology Data Exchange (ETDEWEB)

Eller, Zoltan; Papp, Anita; Hancsok, Jenoe [Pannonia Univ., Veszprem (Hungary). MOL Dept. of Hydrocarbon and Coal Processing

2013-06-01

Recent demands for low aromatic content jet fuels have shown significant increase in the last 20 years. This was generated by the growing of aviation. Furthermore, the quality requirements have become more aggravated for jet fuels. Nowadays reduced aromatic hydrocarbon fractions are necessary for the production of jet fuels with good burning properties, which contribute to less harmful material emission. In the recent past the properties of gasolines and diesel gas oils were continuously severed, and the properties of jet fuels will be more severe, too. Furthermore, it can become obligatory to blend alternative components into jet fuels. With the aromatic content reduction there is a possibility to produce high energy content jet fuels with the desirable properties. One of the possibilities is the blending of biocomponents from catalytic hydrogenation of triglycerides. Our aim was to study the possibilities of producing low sulphur and aromatic content jet fuels in a catalytic way. On a CoMo/Al{sub 2}O{sub 3} catalyst we studied the possibilities of quality improving of a kerosene fraction and coconut oil mixture depending on the change of the process parameters (temperature, pressure, liquid hourly space velocity, volume ratio). Based on the quality parameters of the liquid products we found that we made from the feedstock in the adequate technological conditions products which have a high smoke point (> 35 mm) and which have reduced aromatic content and high paraffin content (90%), so these are excellent jet fuels, and their stack gases damage the environment less. (orig.)

On-Farm, Almond Orchard Flooding as a Viable Aquifer Recharge Alternative

Science.gov (United States)

Ulrich, C.; Nico, P. S.; Wu, Y.; Newman, G. A.; Conrad, M. E.; Dahlke, H. E.

2017-12-01

In 2014, California legislators passed the Sustainable Groundwater Management Act (SGMA), which requires groundwater sustainability agencies (areas) to identify/prioritize water basins, develop current and projected water use/needs, develop a groundwater management plan, develop fees, etc. One of the challenges for implementing SGMA is the lack of data that can support alternative groundwater recharge methods such as on-farm flooding. Prior to anthropogenic river control, river floodplains captured excess water during overbank flow in the rainy season in the CA central valley. Today levees and canals strategically route rainy season high flows to the delta/ocean when irrigation water is not needed. Utilizing farmland once again as infiltration basins for groundwater banking and aquifer recharge could be a viable answer to California's depleted central valley aquifers. Prior to 2017, U.C. Davis had partnered with the Almond Board of California (ABC) and local growers to study the efficacy of agricultural flooding and the effects on annual almond crops (. LBNL joined this team to help understand the conveyance of recharge water, using electrical resistivity tomography (ERT), into the subsurface (i.e. localized fast paths, depth of infiltration, etc.) during flooding events. The fate of the recharge water is what is significant to understanding the viability of on-farm flooding as an aquifer recharge option. In this study two orchards (in Delhi and Modesto, CA), each approximately 2 acres, were flooded during the almond tree dormant period (January), to recharge 2 acre/ft of water into the local aquifers. ERT was used to characterize (soil structure) and monitor water infiltration over a single flooding event to investigate the fate of applied water. Data were collected every hour prior to flooding (baseline), during, and after all flood water had infiltrated (about 5 days total). Our time-lapse ERT results show a heterogeneous soil structure that leads to non

Primer on Motor Fuel Excise Taxes and the Role of Alternative Fuels and Energy Efficient Vehicles

Energy Technology Data Exchange (ETDEWEB)

Schroeder, Alex [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2015-08-26

Motor fuel taxes were established to finance our nation’s transportation infrastructure, yet evolving economic, political, and technological influences are constraining this ability. At the federal level, the Highway Trust Fund (HTF), which is primarily funded by motor fuel taxes, has become increasingly dependent on general fund contributions and short-term reauthorizations to prevent insolvency. As a result, there are discussions at both the federal and state levels in which stakeholders are examining the future of motor fuel excise taxes as well as the role of electric and alternative fuel vehicles in that future. On July 1, 2015, six states increased their motor fuel tax rates.

Demand for alternative-fuel vehicles when registration taxes are high

DEFF Research Database (Denmark)

Mabit, Stefan Lindhard; Fosgerau, Mogens

2011-01-01

This paper investigates the potential futures for alternative-fuel vehicles in Denmark, where the vehicle registration tax is very high and large tax rebates can be given. A large stated choice dataset has been collected concerning vehicle choice among conventional, hydrogen, hybrid, bio......-diesel, and electric vehicles. We estimate a mixed logit model that improves on previous contributions by controlling for reference dependence and allowing for correlation of random effects. Both improvements are found to be important. An application of the model shows that alternative-fuel vehicles with present...... technology could obtain fairly high market shares given tax regulations possible in the present high-tax vehicle market....

Alternative Fuel News: May 2000 Special Edition

Energy Technology Data Exchange (ETDEWEB)

Brennan, A.; Ficker, C.

2000-05-03

In this special issue of Alternative Fuel News, the authors summarize DOE's current position on the local government and private fleet rulemaking that has been under consideration. The authors also look at the new area of focus, niche markets. Your participation and input are invited as the authors craft new directions for the nation's transportation future.

Ignition Delay Properties of Alternative Fuels with Navy-Relevant Diesel Injectors

Science.gov (United States)

2014-06-01

nozzle tip. 8 Figure 3 EMD injector cross-sectional view, after [15]. c. Sturman Injector A Sturman research diesel injector was used to validate...PROPERTIES OF ALTERNATIVE FUELS WITH NAVY-RELEVANT DIESEL INJECTORS by Andrew J. Rydalch June 2014 Thesis Advisor: Christopher M. Brophy...Navy’s Green Fleet Initiative, this thesis researched the ignition characteristics for diesel replacement fuels used with Navy-relevant fuel injectors

Alternative fuels and advanced technology vehicles : issues in Congress

Science.gov (United States)

2009-02-13

Alternative fuels and advanced technology vehicles are seen by proponents as integral to improving urban air quality, decreasing dependence on foreign oil, and reducing emissions of greenhouse gases. However, major barriers especially economics curre...

Analysis of alternative light water reactor (LWR) fuel cycles

International Nuclear Information System (INIS)

Heeb, C.M.; Aaberg, R.L.; Boegel, A.J.; Jenquin, U.P.; Kottwitz, D.A.; Lewallen, M.A.; Merrill, E.T.; Nolan, A.M.

1979-12-01

Nine alternative LWR fuel cycles are analyzed in terms of the isotopic content of the fuel material, the relative amounts of primary and recycled material, the uranium and thorium requirements, the fuel cycle costs and the fraction of energy which must be generated at secured sites. The fuel materials include low-enriched uranium (LEU), plutonium-uranium (MOX), highly-enriched uranium-thorium (HEU-Th), denatured uranium-thorium (DU-Th) and plutonium-thorium (Pu-Th). The analysis is based on tracing the material requirements of a generic pressurized water reactor (PWR) for a 30-year period at constant annual energy output. During this time period all the created fissile material is recycled unless its reactivity worth is less than 0.2% uranium enrichment plant tails

The prospects of use of alternative types of fuel in road transport ...

African Journals Online (AJOL)

The article is devoted to the analysis of possibilities of using alternative types of fuel in transport. Gas engine fuels are considered as potential energy carriers for diesel engines. Since the constructions of vehicles, using gas and traditional types of fuel, have some differences, the most important are the issues of ensuring ...

Power generation costs for alternate reactor fuel cycles

International Nuclear Information System (INIS)

Smolen, G.R.; Delene, J.G.

1980-09-01

The total electric generating costs at the power plant busbar are estimated for various nuclear reactor fuel cycles which may be considered for power generation in the future. The reactor systems include pressurized water reactors (PWR), heavy-water reactors (HWR), high-temperature gas cooled reactors (HTGR), liquid-metal fast breeder reactors (LMFBR), light-water pre-breeder and breeder reactors (LWPR, LWBR), and a fast mixed spectrum reactor (FMSR). Fuel cycles include once-through, uranium-only recycle, and full recycle of the uranium and plutonium in the spent fuel assemblies. The U 3 O 8 price for economic transition from once-through LWR fuel cycles to both PWR recycle and LMFBR systems is estimated. Electric power generation costs were determined both for a reference set of unit cost parameters and for a range of uncertainty in these parameters. In addition, cost sensitivity parameters are provided so that independent estimations can be made for alternate cost assumptions

Effect of Selected Alternative Fuels and Raw Materials on the Cement Clinker Quality

Directory of Open Access Journals (Sweden)

Strigáč Július

2015-11-01

Full Text Available The article deals with the study of the effects of alternative fuels and raw materials on the cement clinker quality. The clinker quality was expressed by the content of two principal minerals alite C3S and belite C2S. The additions of alternative fuels ashes and raw materials, in principle, always increased the belite content and conversely reduced the amount of alite. The alternative fuels with high ash content were used such as the meat-bone meal, sewage sludge from sewage treatment plants and paper sludge and the used alternative raw materials were metallurgical slags - granulated blastfurnace slag, air cooled blastfurnace slag and demetallized steel slag, fluidized bed combustion fly ash and waste glass. Meat-bone meal, sewage sludge from sewage treatment plants and paper sludge were evaluated as moderately suitable alternative fuels which can be added in the amounts of 2.8 wt. % addition of meat-bone meals ash, 3.64 wt. % addition of sewage sludge ash and 3.8 wt. % addition of paper sludge ash to the cement raw mixture. Demetallised steel slag is suitable for production of special sulphate resistant cement clinker for CEM I –SR cement with addition up to 5 wt. %. Granulated blastfurnace slag is a suitable alternative raw material with addition 4 wt. %. Air cooled blastfurnace slag is a suitable alternative raw material with addition 4.2 wt. %. Waste glass is not very appropriate alternative raw material with addition only 1.16 wt. %. Fluidized bed combustion fly ash appears not to be equally appropriate alternative raw material for cement clinker burning with less potential utilization in the cement industry and with addition 3.41 wt. %, which forms undesired anhydrite CaSO4 in the cement clinker.

16 CFR 309.15 - Posting of non-liquid alternative vehicle fuel rating.

Science.gov (United States)

2010-01-01

... rating. (a) If you are a retailer who offers for sale or sells non-liquid alternative vehicle fuel (other... fuel. If you are a retailer who offers for sale or sells electricity to consumers through an electric... vehicle fuel dispensing system, either by letter or on the delivery ticket or other paper, or by a...

10 CFR 503.31 - Lack of alternate fuel supply for the first 10 years of useful life.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Lack of alternate fuel supply for the first 10 years of useful life. 503.31 Section 503.31 Energy DEPARTMENT OF ENERGY (CONTINUED) ALTERNATE FUELS NEW FACILITIES Permanent Exemptions for New Facilities § 503.31 Lack of alternate fuel supply for the first 10 years of...

Analysis of operational, institutional and international limitations for alternative fuel vehicles and technologies: Means/methods for implementing changes

Energy Technology Data Exchange (ETDEWEB)

1992-07-01

This project focused upon the development of an approach to assist public fleet managers in evaluating the characteristics and availability of alternative fuels (AF`s) and alternative fuel vehicles (AFV`s) that will serve as possible replacements for vehicles currently serving the needs of various public entities. Also of concern were the institutional/international limitations for alternative fuels and alternative fuel vehicles. The City of Detroit and other public agencies in the Detroit area were the particular focus for the activities. As the development and initial stages of use of alternative fuels and alternative fuel vehicles proceeds, there will be an increasing need to provide information and guidance to decision-makers regarding differences in requirements and features of these fuels and vehicles. There wig be true differences in requirements for servicing, managing, and regulating. There will also be misunderstanding and misperception. There have been volumes of data collected on AFV`S, and as technology is improved, new data is constantly added. There are not, however, condensed and effective sources of information for public vehicle fleet managers on vehicle and equipment sources, characteristics, performance, costs, and environmental benefits. While theoretical modeling of public fleet requirements has been done, there do not seem to be readily available ``practical``. There is a need to provide the best possible information and means to minimize the problems for introducing the effective use of alternative fuels and alternative fuel vehicles.

Clean Cities Guide to Alternative Fuel and Advanced Medium- and Heavy-Duty Vehicles

Energy Technology Data Exchange (ETDEWEB)

None

2013-08-01

Today's fleets are increasingly interested in medium-duty and heavy-duty vehicles that use alternative fuels or advanced technologies that can help reduce operating costs, meet emissions requirements, improve fleet sustainability, and support U.S. energy independence. Vehicle and engine manufacturers are responding to this interest with a wide range of options across a steadily growing number of vehicle applications. This guide provides an overview of alternative fuel power systems--including engines, microturbines, electric motors, and fuel cells--and hybrid propulsion systems. The guide also offers a list of individual medium- and heavy-duty vehicle models listed by application, along with associated manufacturer contact information, fuel type(s), power source(s), and related information.

TAFV Alternative Fuels and Vehicles Choice Model Documentation; TOPICAL

International Nuclear Information System (INIS)

Greene, D.L.

2001-01-01

A model for predicting choice of alternative fuel and among alternative vehicle technologies for light-duty motor vehicles is derived. The nested multinomial logit (NML) mathematical framework is used. Calibration of the model is based on information in the existing literature and deduction based on assuming a small number of key parameters, such as the value of time and discount rates. A spreadsheet model has been developed for calibration and preliminary testing of the model

Physiology limits commercially viable photoautotrophic production of microalgal biofuels.

Science.gov (United States)

Kenny, Philip; Flynn, Kevin J

2017-01-01

Algal biofuels have been offered as an alternative to fossil fuels, based on claims that microalgae can provide a highly productive source of compounds as feedstocks for sustainable transport fuels. Life cycle analyses identify algal productivity as a critical factor affecting commercial and environmental viability. Here, we use mechanistic modelling of the biological processes driving microalgal growth to explore optimal production scenarios in an industrial setting, enabling us to quantify limits to algal biofuels potential. We demonstrate how physiological and operational trade-offs combine to restrict the potential for solar-powered algal-biodiesel production in open ponds to a ceiling of ca. 8000 L ha -1 year -1 . For industrial-scale operations, practical considerations limit production to ca. 6000 L ha -1 year -1 . According to published economic models and life cycle analyses, such production rates cannot support long-term viable commercialisation of solar-powered cultivation of natural microalgae strains exclusively as feedstock for biofuels. The commercial viability of microalgal biofuels depends critically upon limitations in microalgal physiology (primarily in rates of C-fixation); we discuss the scope for addressing this bottleneck concluding that even deployment of genetically modified microalgae with radically enhanced characteristics would leave a very significant logistical if not financial burden.

Automobiles and global warming: Alternative fuels and other options for carbon dioxide emissions reduction

International Nuclear Information System (INIS)

Sagar, A.D.

1995-01-01

Automobiles are a source of considerable pollution at the global level, including a significant fraction of the total greenhouse gas emissions. Alternative fuels have received some attention as potential options to curtail the carbon dioxide emissions from motor vehicles. This article discusses the feasibility and desirability (from a technical as well as a broader environmental perspective) of the large-scale production and use of alternative fuels as a strategy to mitigate automotive carbon dioxide emissions. Other options such as improving vehicle efficiency and switching to more efficient modes of passenger transportation are also discussed. These latter options offer an effective and immediate way to tackle the greenhouse and other pollutant emission from automobiles, especially as the limitations of currently available alternative fuels and the technological and other constraints for potential future alternatives are revealed

Comparison of alternatives for the treatment of non-fuel-bearing hardware

International Nuclear Information System (INIS)

Ross, W.A.; Clark, L.L.; Oma, K.H.

1987-01-01

This evaluation compares four alternatives for the treatment or processing of non-fuel-bearing hardware (NFBH) to reduce its volume and prepare it for disposal. These treatment alternatives are: shredding; shredding and low-pressure compaction; shredding and supercompaction; and melting. The alternatives are compared on the bases of system costs, waste form characteristics, and process considerations. The two alternatives with high volume reduction are estimated to save $400 million to $500 million compared with the shredding-only alternative. The study recommends that melting and supercompaction alternatives be considered further and that additional testing be conducted for these two alternatives

Cost-benefit analysis of alternative fuels and motive designs.

Science.gov (United States)

2013-04-01

This project was funded by the Federal Railroad Administration to better understand the potential cost and benefits of using alternative fuels for U.S. freight and passenger locomotive operations. The framework for a decision model was developed by T...

Spray and atomization of diesel fuel and its alternatives from a single-hole injector using a common rail fuel injection system

KAUST Repository

Chen, PinChia; Wang, Weicheng; Roberts, William L.; Fang, Tiegang

2013-01-01

Fuel spray and atomization characteristics play an important role in the performance of internal combustion engines. As the reserves of petroleum fuel are expected to be depleted within a few decades, finding alternative fuels that are economically

Evaluation Framework for Alternative Fuel Vehicles: Sustainable Development Perspective

Directory of Open Access Journals (Sweden)

Dong-Shang Chang

2015-08-01

Full Text Available Road transport accounts for 72.06% of total transport CO2, which is considered a cause of climate change. At present, the use of alternative fuels has become a pressing issue and a significant number of automakers and scholars have devoted themselves to the study and subsequent development of alternative fuel vehicles (AFVs. The evaluation of AFVs should consider not only air pollution reduction and fuel efficiency but also AFV sustainability. In general, the field of sustainable development is subdivided into three areas: economic, environmental, and social. On the basis of the sustainable development perspective, this study presents an evaluation framework for AFVs by using the DEMATEL-based analytical network process. The results reveal that the five most important criteria are price, added value, user acceptance, reduction of hazardous substances, and dematerialization. Price is the most important criterion because it can improve the popularity of AFVs and affect other criteria, including user acceptance. Additional, the energy usage criterion is expected to significantly affect the sustainable development of AFVs. These results should be seriously considered by automakers and governments in developing AFVs.

The California Multimedia Risk Assessment Protocol for Alternative Fuels

Science.gov (United States)

Hatch, T.; Ginn, T. R.; McKone, T. E.; Rice, D. W.

2013-12-01

Any new fuel in California requires approval by the state agencies overseeing human and environmental health. In order to provide a systematic evaluation of new fuel impacts, California now requires a multimedia risk assessment (MMRA) for fuel approval. The fuel MMRA involves all relevant state agencies including: the California Air Resources Board (CARB), the State Water Resources Control Board (SWRCB), the Office of Environmental Health Hazards Assessment (OEHHA), and the Department of Toxic Substances Control (DTSC) overseen by the California Environmental Protection Agency (CalEPA). The lead agency for MMRAs is the CARB. The original law requiring a multimedia assessment is California Health and Safety Code 43830.8. In addition, the low carbon fuel standard (LCFS), the Global Warming Solutions Act (AB32), and the Verified Diesel Emission Control Strategy (VDECS) have provisions that can require a multimedia assessment. In this presentation, I give an overview of the California multimedia risk assessment (MMRA) for new fuels that has been recently developed and applied to several alternative fuels. The objective of the California MMRA is to assess risk of potential impacts of new fuels to multiple environmental media including: air, water, and soil. Attainment of this objective involves many challenges, including varying levels of uncertainty, relative comparison of incommensurate risk factors, and differing levels of priority assigned to risk factors. The MMRA is based on a strategy of relative risk assessment and flexible accommodation of distinct and diverse fuel formulations. The approach is tiered by design, in order to allow for sequentially more sophisticated investigations as knowledge gaps are identified and re-prioritized by the ongoing research. The assessment also involves peer review in order to provide coupling between risk assessment and stakeholder investment, as well as constructive or confrontational feedback. The multimedia assessment

Alternative Fuel and Advanced Technology Commercial Lawn Equipment (Spanish version); Clean Cities, Energy Efficiency & Renewable Energy (EERE)

Energy Technology Data Exchange (ETDEWEB)

Nelson, Erik

2015-06-01

Powering commercial lawn equipment with alternative fuels or advanced engine technology is an effective way to reduce U.S. dependence on petroleum, reduce harmful emissions, and lessen the environmental impacts of commercial lawn mowing. Numerous alternative fuel and fuel-efficient advanced technology mowers are available. Owners turn to these mowers because they may save on fuel and maintenance costs, extend mower life, reduce fuel spillage and fuel theft, and demonstrate their commitment to sustainability.

Integration Workshop on Alternative Fuels in the EU Energy System, Petten, 22-23 November 2004. Summary Report

International Nuclear Information System (INIS)

Tzimas, E.; Peteves, S.D.

2005-01-01

The aim of the title Workshop was to: (a) provide information on the related Commission actions and policies, (b) assess key technological developments and describe the state of the art of alternative fuel technologies, and, (c) identify the techno-economic barriers associated with the introduction of alternative fuels in the EU energy system and more specifically, in its new Member States and Candidate Countries. The Workshop attracted a specialised audience of delegates from most of the New Member States and the Candidate Countries, who are directly involved with the preparation, development, implementation and monitoring of policies relevant to alternative fuels, as well as with related applied research and development. The Workshop facilitated the exchange of experiences and views among the participants on the optimal approaches that could lead to the successful introduction of alternative fuels in the energy system of each country. To this end, short informal presentations were solicited from each participating country about the prospective introduction of alternative fuels in their national energy system. These presentations were coupled by longer presentations made by experts on the following topics: The European Commission perspective on alternative fuels; A well-to-wheels assessment of alternative fuels; The European biomass potential, the prospects for biogas, and a review of advanced production methods for biofuels; An assessment of the European natural gas market, and a description of the state-of-the-art of natural gas vehicle technology. This report summarises the main points made by the participants, the outcome of the discussions and some thoughts on future actions that may be implemented by the JRC in support of initiatives taken by the New Member States and Candidate Countries concerning alternative fuels

Assessment of Energy Performance and Emission Control Using Alternative Fuels in Cement Industry through a Process Model

Directory of Open Access Journals (Sweden)

Azad Rahman

2017-12-01

Full Text Available Cement manufacturing is one of the most energy intensive processes and is accountable for substantial pollutant emissions. Increasing energy costs compel stakeholders and researchers to search for alternative options to improve energy performance and reduce CO2 emissions. Alternative fuels offer a realistic solution towards the reduction of the usage of fossil fuels and the mitigation of pollutant emissions. This paper developed a process model of a precalciner kiln system in the cement industry using Aspen Plus software to simulate the effect of five alternative fuels on pollutant emissions and energy performance. The alternatives fuels used were tyre, municipal solid waste (MSW, meat and bone meal (MBM, plastic waste and sugarcane bagasse. The model was developed on the basis of energy and mass balance of the system and was validated against data from a reference cement plant. This study also investigated the effect of these alternative fuels on the quality of the clinker. The results indicated that up to a 4.4% reduction in CO2 emissions and up to a 6.4% reduction in thermal energy requirement could be achieved using these alternative fuels with 20% mix in coal. It was also found that the alternative fuels had minimum influence on the clinker quality except in the case of MSW. Overall, MBM was found to be a better option as it is capable on reducing energy requirement and CO2 emissions more than others. The outcomes of the study offer better understanding of the effects of solid alternative fuels to achieve higher energy performance and on mitigating pollutant emissions in cement industry.

Alternative fuel cycle options: performance characteristics and impact on nuclear power growth potential

International Nuclear Information System (INIS)

Chang, Y.I.; Till, C.E.; Rudolph, R.R.; Deen, J.R.; King, M.J.

1977-09-01

The fuel utilization characteristics for LWR, SSCR, CANDU and LMFBR reactor concepts are quantified for various fuel cycle options, including once-through cycles, thorium cycles, and denatured cycles. The implications of various alternative reactor deployment strategies on the long-term nuclear power growth potential are then quantified in terms of the maximum nuclear capacity that can be achieved and the growth pattern over time, subject to the constraint of a fixed uranium-resource base. The overall objective of this study is to shed light on any large differences in the long-term potential that exist between various alternative reactor/fuel cycle deployment strategies

Findings and Recommendations from the NIST Workshop on Alternative Fuels and Materials: Biocorrosion.

Science.gov (United States)

Mansfield, Elisabeth; Sowards, Jeffrey W; Crookes-Goodson, Wendy J

2015-01-01

In 2013, the Applied Chemicals and Materials Division of the National Institute of Standards and Technology (NIST) hosted a workshop to identify and prioritize research needs in the area of biocorrosion. Materials used to store and distribute alternative fuels have experienced an increase in corrosion due to the unique conditions caused by the presence of microbes and the chemistry of biofuels and biofuel precursors. Participants in this workshop, including experts from the microbiological, fuel, and materials communities, delved into the unique materials and chemical challenges that occur with production, transport, and storage of alternative fuels. Discussions focused on specific problems including: a) the changing composition of "drop-in" fuels and the impact of that composition on materials; b) the influence of microbial populations on corrosion and fuel quality; and c) state-of-the-art measurement technologies for monitoring material degradation and biofilm formation.

Guide for Identifying and Converting High-Potential Petroleum Brownfield Sites to Alternative Fuel Stations

Energy Technology Data Exchange (ETDEWEB)

Johnson, C.; Hettinger, D.; Mosey, G.

2011-05-01

Former gasoline stations that are now classified as brownfields can be good sites to sell alternative fuels because they are in locations that are convenient to vehicles and they may be seeking a new source of income. However, their success as alternative fueling stations is highly dependent on location-specific criteria. First, this report outlines what these criteria are, how to prioritize them, and then applies that assessment framework to five of the most popular alternative fuels--electricity, natural gas, hydrogen, ethanol, and biodiesel. The second part of this report delves into the criteria and tools used to assess an alternative fuel retail site at the local level. It does this through two case studies of converting former gasoline stations in the Seattle-Eugene area into electric charge stations. The third part of this report addresses steps to be taken after the specific site has been selected. This includes choosing and installing the recharging equipment, which includes steps to take in the permitting process and key players to include.

Impact of alternative fuels on the operational and environmental performance of a small turbofan engine

International Nuclear Information System (INIS)

Gaspar, R.M.P.; Sousa, J.M.M.

2016-01-01

Highlights: • A wide range of alternative fuels is studied in a small two-spool turbofan engine. • Impact of fuel properties on flame temperature and droplet evaporation considered. • Performance and pollutant emissions at different operating conditions are analyzed. • Use of alternative fuels generally leads to an improved performance of the engine. • Mostly reductions in soot emissions, but also cuts in NO_x and CO, are obtained. - Abstract: A wide range of alternative jet fuels is studied in this work for use in a small two-spool turbofan engine. These embrace the five production pathways currently approved by the American Society for Testing and Materials. Both neat products and blends (within certified limits) have been considered. The present analysis is based on a 0-D thermodynamic modeling of the aero-engine for off-design and transient simulations. In addition, the selected approach incorporates fuel effects on combustion and the impact of fuel properties on the flame temperature, as well as on the droplet evaporation rate. Predicted performance and pollutant emission outputs for the alternative fuels are presented at different operating conditions, namely: take-off, top of climb, cruise, low power and ground idle. The results are discussed and comprehensively compared with data available in the literature. It was concluded that the combustion of alternative fuels generally leads to enhancements in engine performance with respect to the use of conventional kerosene. Reductions in pollutant emissions occur mostly in soot, but also in nitrogen oxides and carbon monoxide, depending on the fuel and operating conditions. In contrast, increased emissions of unburned hydrocarbons are generally observed. Concerns about the aero-engine dynamic response are raised only in very few cases, involving the use of neat products.

Alternative Fuels in Epilepsy and Amyotrophic Lateral Sclerosis.

Science.gov (United States)

Tefera, Tesfaye W; Tan, Kah Ni; McDonald, Tanya S; Borges, Karin

2017-06-01

This review summarises the recent findings on metabolic treatments for epilepsy and Amyotrophic Lateral Sclerosis (ALS) in honour of Professor Ursula Sonnewald. The metabolic impairments in rodent models of these disorders as well as affected patients are being discussed. In both epilepsy and ALS, there are defects in glucose uptake and reduced tricarboxylic acid (TCA) cycling, at least in part due to reduced amounts of C4 TCA cycle intermediates. In addition there are impairments in glycolysis in ALS. A reduction in glucose uptake can be addressed by providing the brain with alternative fuels, such as ketones or medium-chain triglycerides. As anaplerotic fuels, such as the triglyceride of heptanoate, triheptanoin, refill the TCA cycle C4/C5 intermediate pool that is deficient, they are ideal to boost TCA cycling and thus the oxidative metabolism of all fuels.

Fuel cell power plants for automotive applications

Science.gov (United States)

McElroy, J. F.

1983-02-01

While the Solid Polymer Electrolyte (SPE) fuel cell has until recently not been considered competitive with such commercial and industrial energy systems as gas turbine generators and internal combustion engines, electrical current density improvements have markedly improved the capital cost/kW output rating performance of SPE systems. Recent studies of SPE fuel cell applicability to vehicular propulsion have indicated that with adequate development, a powerplant may be produced which will satisfy the performance, size and weight objectives required for viable electric vehicles, and that the cost for such a system would be competitive with alternative advanced power systems.

Alternate-Fueled Combustor-Sector Performance. Parts A and B; (A) Combustor Performance; (B) Combustor Emissions

Science.gov (United States)

Shouse, D. T.; Hendricks, R. C.; Lynch, A.; Frayne, C. W.; Stutrud, J. S.; Corporan, E.; Hankins, T.

2012-01-01

Alternate aviation fuels for military or commercial use are required to satisfy MIL-DTL-83133F(2008) or ASTM D 7566 (2010) standards, respectively, and are classified as "drop-in" fuel replacements. To satisfy legacy issues, blends to 50% alternate fuel with petroleum fuels are certified individually on the basis of processing and assumed to be feedstock agnostic. Adherence to alternate fuels and fuel blends requires "smart fueling systems" or advanced fuel-flexible systems, including combustors and engines, without significant sacrifice in performance or emissions requirements. This paper provides preliminary performance (Part A) and emissions and particulates (Part B) combustor sector data. The data are for nominal inlet conditions at 225 psia and 800 F (1.551 MPa and 700 K), for synthetic-paraffinic-kerosene- (SPK-) type (Fisher-Tropsch (FT)) fuel and blends with JP-8+100 relative to JP-8+100 as baseline fueling. Assessments are made of the change in combustor efficiency, wall temperatures, emissions, and luminosity with SPK of 0%, 50%, and 100% fueling composition at 3% combustor pressure drop. The performance results (Part A) indicate no quantifiable differences in combustor efficiency, a general trend to lower liner and higher core flow temperatures with increased FT fuel blends. In general, emissions data (Part B) show little differences, but with percent increase in FT-SPK-type fueling, particulate emissions and wall temperatures are less than with baseline JP-8. High-speed photography illustrates both luminosity and combustor dynamic flame characteristics.

Performance of metallic fuels in liquid-metal fast reactors

International Nuclear Information System (INIS)

Seidel, B.R.; Walters, L.C.; Kittel, J.H.

1984-01-01

Interest in metallic fuels for liquid-metal fast reactors has come full circle. Metallic fuels are once again a viable alternative for fast reactors because reactor outlet temperature of interest to industry are well within the range where metallic fuels have demonstrated high burnup and reliable performance. In addition, metallic fuel is very tolerant of off-normal events of its high thermal conductivity and fuel behavior. Futhermore, metallic fuels lend themselves to compact and simplified reprocessing and refabrication technologies, a key feature in a new concept for deployment of fast reactors called the Integral Fast Reactor (IFR). The IFR concept is a metallic-fueled pool reactor(s) coupled to an integral-remote reprocessing and fabrication facility. The purpose of this paper is to review recent metallic fuel performance, much of which was tested and proven during the twenty years of EBR-II operation

Utilizing Philippine Calatrava coal-diesel oil mixture (CDOM) as alternative fuel for industrial steam generator

Energy Technology Data Exchange (ETDEWEB)

Archie B. Maglaya [De La Salle University, Manila (Philippines). Department of Mechanical Engineering

2005-01-01

The fast depletion of fuel oil and the continuous increase in the demand for power is a global issue. In the Philippines, the demand for diesel oil is expected to increase significantly in a 20-year period as projected by the Department of Energy. In line with the Philippine Government's thrust to lessen the dependence on imported energy, the agenda for the search for alternative fuel is highly prioritized. Thus, this paper presents the results of the study on performance analysis and efficiency test of a diesel oil fired industrial steam generator using Philippine Calatrava coal-diesel oil mixture (CDOM) as alternative fuel. A computer program was developed in HyperText Markup Language (HTML{copyright}) and JavaScript{copyright} to aid the computation of the adiabatic flame temperature from the governing system of equations based on the heat interaction between CDOM fuel, combustion air and products of combustion to determine the most desirable alternative fuel. Actual experimentation for the determination of CDOM fuel properties was also conducted to verify the alternative fuel selected through theoretical calculations. Results showed that the CDOM fuel with a particle size passing 75 {mu}m (-200 mesh) sieve having a proportion of 5% pulverized coal-95% diesel oil and 10% pulverized coal-90% diesel oil could be handled throughout the test with no degradation of the industrial steam generator. The steam generator efficiency using diesel oil is close to the steam generator efficiency using both CDOM fuels. 20 refs., 5 figs., 4 tabs.

California's experience with alternative fuel vehicles

International Nuclear Information System (INIS)

Sullivan, C.

1993-01-01

California is often referred to as a nation-state, and in many aspects fits that description. The state represents the seventh largest economy in the world. Most of California does not have to worry about fuel to heat homes in the winter. What we do worry about is fuel for our motor vehicles, approximately 24 million of them. In fact, California accounts for ten percent of new vehicle sales in the United States each year, much of it used in the transportation sector. The state is the third largest consumer of gasoline in the world, only exceeded by the United States as a whole and the former Soviet Union. California is also a leader in air pollution. Of the nine worst ozone areas in the country cited in the 1990 Clean Air Act Amendments, two areas the Los Angeles Basin and San Diego are located in California. Five of California's cities made the top 20 smoggiest cities in the United States. In reality, all of California's major metropolitan areas have air quality problems. This paper will discuss the beginnings of California's investigations of alternative fuels use in vehicles; the results of the state's demonstration programs; and future plans to improve California's air quality and energy security in the mobile sector

Alternative Fuel News, Vol. 2, No. 6

Energy Technology Data Exchange (ETDEWEB)

NREL

1999-03-17

The cover story in this issue of the Alternative Fuel News highlights the niche market principle; the places in which AFVs would best fit. This year's SEP funding is expected to be the springboard needed for the development of niche projects. The Clean Cities Program, by matching those needs and attributes in niches, can dramatically increase the attractiveness of AFVs and make an impact on those high-mileage, high-use fleets.

Alternative Fuel Transportation Optimization Tool : Description, Methodology, and Demonstration Scenarios.

Science.gov (United States)

2015-09-01

This report describes an Alternative Fuel Transportation Optimization Tool (AFTOT), developed by the U.S. Department of Transportation (DOT) Volpe National Transportation Systems Center (Volpe) in support of the Federal Aviation Administration (FAA)....

Electrocatalysis of fuel cell reactions: Investigation of alternate electrolytes

Science.gov (United States)

Chin, D. T.; Hsueh, K. L.; Chang, H. H.

1984-01-01

Oxygen reduction and transport properties of the electrolyte in the phosphoric acid fuel cell are studied. The areas covered were: (1) development of a theoretical expression for the rotating ring disk electrode technique; (2) determination of the intermediate reaction rate constants for oxygen reduction on platinum in phosphoric acid electrolyte; (3) determination of oxygen reduction mechanism in trifluoreomethanesulfonic acid (TFMSA) which was considered as an alternate electrolyte for the acid fuel cells; and (4) the measurement of transport properties of the phosphoric acid electrolyte at high concentrations and temperatures.

Impact of Alternative Jet Fuels on Engine Exhaust Composition During the 2015 ECLIF Ground-Based Measurements Campaign.

Science.gov (United States)

Schripp, Tobias; Anderson, Bruce; Crosbie, Ewan C; Moore, Richard H; Herrmann, Friederike; Oßwald, Patrick; Wahl, Claus; Kapernaum, Manfred; Köhler, Markus; Le Clercq, Patrick; Rauch, Bastian; Eichler, Philipp; Mikoviny, Tomas; Wisthaler, Armin

2018-04-17

The application of fuels from renewable sources ("alternative fuels") in aviation is important for the reduction of anthropogenic carbon dioxide emissions, but may also attribute to reduced release of particles from jet engines. The present experiment describes ground-based measurements in the framework of the ECLIF (Emission and Climate Impact of Alternative Fuels) campaign using an Airbus A320 (V2527-A5 engines) burning six fuels of chemically different composition. Two reference Jet A-1 with slightly different chemical parameters were applied and further used in combination with a Fischer-Tropsch synthetic paraffinic kerosene (FT-SPK) to prepare three semi synthetic jet fuels (SSJF) of different aromatic content. In addition, one commercially available fully synthetic jet fuel (FSJF) featured the lowest aromatic content of the fuel selection. Neither the release of nitrogen oxide or carbon monoxide was significantly affected by the different fuel composition. The measured particle emission indices showed a reduction up to 50% (number) and 70% (mass) for two alternative jet fuels (FSJF, SSJF2) at low power settings in comparison to the reference fuels. The reduction is less pronounced at higher operating conditions but the release of particle number and particle mass is still significantly lower for the alternative fuels than for both reference fuels. The observed correlation between emitted particle mass and fuel aromatics is not strict. Here, the H/C ratio is a better indicator for soot emission.

Global warming and urban smog: The cost effectiveness of CAFE standards and alternative fuels

International Nuclear Information System (INIS)

Krupnick, A.J.; Walls, M.A.; Collins, C.T.

1992-01-01

This paper evaluates alternative transportation policies for reducing greenhouse gas emissions and ozone precursors. The net cost-effectiveness -- i.e., the cost per ton of greenhouse gas reduced, adjusted for ozone reduction benefits -- of substituting methanol, compressed natural gas (CNG), and reformulated gasoline for conventional gasoline is assessed and compared with the cost-effectiveness of raising the corporate average fuel economy (CAFE) standard to 38 miles per gallon. Computing this open-quotes netclose quotes cost-effectiveness is one way of measuring the joint environmental benefits that these alternatives provide. Greenhouse gas emissions are assessed over the entire fuel cycle and include not only carbon dioxide emissions, but also methane, carbon monoxide, and nitrous oxide emissions. In computing cost-effectiveness, we account for the so-called open-quotes rebound effectclose quotes -- the impact on vehicle-miles traveled of higher or lower fuel costs. CNG is found to be the most cost-effective of these alternatives, followed by increasing the CAFE standard, substituting methanol for gasoline, and substituting reformulated for conventional gasoline. Including the ozone reduction benefits does not change the rankings of the alternatives, but does make the alternative fuels look better relative to increasing the CAFE standard. Incorporating the rebound effect greatly changes the magnitude of the estimates but does not change the rankings of the alternatives. None of the alternatives look cost-effective should a carbon tax of $35 per ton be passes (the proposal in the Stark bill, H.R. 1086), and only CNG under optimistic assumptions looks cost-effective if a tax of $100 per ton of carbon is passed

Spent-fuel management strategies at Carolina Power ampersand Light Company

International Nuclear Information System (INIS)

Thompson, M.F. Jr.; Kunita, R.K.

1990-01-01

Carolina Power ampersand Light (CP ampersand L) Company serves customers in portions of both North and South Carolina, and operates the Robinson 2, Brunswick 1 and 2, and Harris nuclear units. Due first to licensing delays in the Allied General Nuclear Service reprocessing plant and then to actions and inactions by the federal government, CP ampersand L like other utilities, is concerned with the storage of spent fuel. Despite pool reracking to the maximum practical, further actions have been necessary; hence, CP ampersand L undertook efforts to make both dry storage and transshipment viable alternatives. Based on experience, it is found that while both dry storage and transshipment are viable options, transshipment is the better strategy for CP ampersand L. Dry storage will be maintained as an alternative strategy

Alternatives for managing wastes from reactors and post-fission operations in the LWR fuel cycle. Volume 3. Alternatives for interim storage and transportation

International Nuclear Information System (INIS)

1976-05-01

Volume III of the five-volume report contains information on alternatives for interim storage and transportation. Section titles are: interim storage of spent fuel elements; interim storage of chop-leach fuel bundle residues; tank storage of high-level liquid waste; interim storage of solid non-high-level wastes; interim storage of solidified high-level waste; and, transportation alternatives

Clean Cities Guide to Alternative Fuel and Advanced Medium- and Heavy-Duty Vehicles (Book)

Energy Technology Data Exchange (ETDEWEB)

2013-08-01

Today's fleets are increasingly interested in medium-duty and heavy-duty vehicles that use alternative fuels or advanced technologies that can help reduce operating costs, meet emissions requirements, improve fleet sustainability, and support U.S. energy independence. Vehicle and engine manufacturers are responding to this interest with a wide range of options across a steadily growing number of vehicle applications. This guide provides an overview of alternative fuel power systems?including engines, microturbines, electric motors, and fuel cells?and hybrid propulsion systems. The guide also offers a list of individual medium- and heavy-duty vehicle models listed by application, along with associated manufacturer contact information, fuel type(s), power source(s), and related information.

The origin and fate of organic pollutants from the combustion of alternative fuels

International Nuclear Information System (INIS)

1995-06-01

The overall objective of this project is to determine the impact of alternative fuels on air quality, particularly ozone formation. The objective will be met through three steps: (1) qualitative identification of alternative fuel combustion products, (2) quantitative measurement of specific emission levels of these products, and (3) determination of the fate of the combustion products in the atmosphere. The alternative fuels of interest are methanol, ethanol, natural gas, and LP gas. The role of the University of Dayton Research Institute (UDRI) in this project is two-fold. First, fused silica flow reactor instrumentation is being used to obtain both qualitative identification and quantitative data on the thermal degradation products from the fuel-lean (oxidative), stoichiometric, and fuel-rich (pyrolytic) decomposition of methanol, ethanol, liquefied petroleum gas, and natural gas. Secondly, a laser photolysis/laser-induced fluorescence (LP/LIF) apparatus is being used to determine the rates and mechanisms of reaction of selected degradation products under atmospheric conditions. This draft final report contains the results of the second year of the study. The authors initially discuss the results of their flow reactor studies. This is followed by a discussion of the initial results from their LP/LIF studies of the reaction of hydroxyl (OH) radicals with methanol and ethanol. In the coming year, they plan to obtain quantitative data on the oxidation of methyl-t-butyl-ether and reformulated gasoline under fuel-lean, stoichiometric, and fuel-rich conditions. They also plan to conduct a mechanistic analysis of the reaction of OH with acetaldehyde and formaldehyde over an extended temperature range

Solid oxide fuel cells for transportation: A clean, efficient alternative for propulsion

International Nuclear Information System (INIS)

Kumar, R.; Krumpelt, M.; Myles, K.M.

1993-01-01

Fuel cells show great promise for providing clean and efficient transportation power. Of the fuel cell propulsion systems under investigation, the solid oxide fuel cell (SOFC) is particularly attractive for heavy duty transportation applications that have a relatively long duty cycle, such as locomotives, trucks, and barges. Advantages of the SOFC include a simple, compact system configuration; inherent fuel flexibility for hydrocarbon and alternative fuels; and minimal water management. The specific advantages of the SOFC for powering a railroad locomotive are examined. Feasibility, practicality, and safety concerns regarding SOFCs in transportation applications are discussed, as am the major R ampersand D issues

Retrofitting a spent fuel pool spray system for alternative cooling as a strategy for beyond design basis events

Energy Technology Data Exchange (ETDEWEB)

Hartmann, Christoph; Vujic, Zoran [Westinghouse Electric Germany GmbH, Mannheim (Germany)

2017-06-15

Due to requirements for nuclear power plants to withstand beyond design basis accidents, including events such as happened in 2011 in the Fukushima Daiichi Nuclear Power Plant in Japan, alternative cooling of spent fuel is needed. Alternative spent fuel cooling can be provided by a retrofitted spent fuel pool spray system based on the AP1000 plant design. As part of Krsko Nuclear Power Plant's Safety Upgrade Program, Krsko Nuclear Power Plant decided on, and Westinghouse successfully designed a retrofit of the AP1000 {sup registered} plant spent fuel pool spray system to provide alternative spent fuel cooling.

Transitioning to a Hydrogen Future: Learning from the Alternative Fuels Experience

Energy Technology Data Exchange (ETDEWEB)

Melendez, M.

2006-02-01

This paper assesses relevant knowledge within the alternative fuels community and recommends transitional strategies and tactics that will further the hydrogen transition in the transportation sector.

National action framework for the development of alternative fuels in the transport sector and the deployment of corresponding infrastructures in application of article 3 of the 2014/97/EU directive of 22 October 2014 on the deployment of an infrastructure for alternative fuels

International Nuclear Information System (INIS)

2016-01-01

This report proposes a detailed overview of the present situation and perspectives of development of alternative fuels and of the corresponding infrastructures. It presents, first, the various existing alternate fuels (electricity, NVG, LNG, LPG, hydrogen, biofuels etc), then the measures taken to develop fueling infrastructures over the French territory, including harbors and inland waterways, and finally, the follow-up and perspectives of the implementation of the National action framework for the development of alternative fuels

40 CFR 1045.645 - What special provisions apply for converting an engine to use an alternate fuel?

Science.gov (United States)

2010-07-01

... converting an engine to use an alternate fuel? 1045.645 Section 1045.645 Protection of Environment... for converting an engine to use an alternate fuel? A certificate of conformity is no longer valid for.... This section applies if such modifications are done to convert the engine to run on a different fuel...

40 CFR 1051.650 - What special provisions apply for converting a vehicle to use an alternate fuel?

Science.gov (United States)

2010-07-01

... converting a vehicle to use an alternate fuel? 1051.650 Section 1051.650 Protection of Environment... vehicle to use an alternate fuel? A certificate of conformity is no longer valid for a vehicle if the... applies if such modifications are done to convert the vehicle to run on a different fuel type. Such...

40 CFR 1054.645 - What special provisions apply for converting an engine to use an alternate fuel?

Science.gov (United States)

2010-07-01

... converting an engine to use an alternate fuel? 1054.645 Section 1054.645 Protection of Environment... apply for converting an engine to use an alternate fuel? A certificate of conformity is no longer valid... fuel type. Such engines may need to be recertified as specified in this section if the certificate is...

Use of nuclear fusion systems for spent nuclear fuel degradation

International Nuclear Information System (INIS)

Nieto, M.; Ramos, G.; Herrera V, J. J. E.

2009-10-01

One of the severe problems of the nuclear industry that should be resolved to facilitate its acceptance like viable energy alternative is of the wastes. In spite of having alternative of fuel reprocessing, many of them have been abandoned by economic or security reasons. In the present work, the alternative is described for using reactors of nuclear fusion as sources of fast neutrons with two important applications in mind: the plutonium burning and the transmutation of the elements that contribute in way more important to their radioactivity, mainly the smaller actinides and the fission products of long half life. (Author)

Assessment of costs and benefits of flexible and alternative fuel use in the US transportation sector

International Nuclear Information System (INIS)

1991-10-01

The DOE is conducting a comprehensive technical analysis of a flexible-fuel transportation system in the United States -- that is, a system that could easily switch between petroleum and another fuel, depending on price and availability. The DOE Alternative Fuels Assessment is aimed directly at questions of energy security and fuel availability, but covers a wide range of issues. This report examines environmental, health, and safety concerns associated with a switch to alternative- and flexible-fuel vehicles. Three potential alternatives to oil-based fuels in the transportation sector are considered: methanol, compressed natural gas (CNG), and electricity. The objective is to describe and discuss qualitatively potential environmental, health, and safety issues that would accompany widespread use of these three fuels. This report presents the results of exhaustive literature reviews; discussions with specialists in the vehicular and fuel-production industries and with Federal, State, and local officials; and recent information from in-use fleet tests. Each chapter deals with the end-use and process emissions of air pollutants, presenting an overview of the potential air pollution contribution of the fuel --relative to that of gasoline and diesel fuel -- in various applications. Carbon monoxide, particulate matter, ozone precursors, and carbon dioxide are emphasized. 67 refs., 6 figs. , 8 tabs

Energy system aspects of hydrogen as an alternative fuel in transport

International Nuclear Information System (INIS)

Ramesohl, Stephan; Merten, Frank

2006-01-01

Considering the enormous ecological and economic importance of the transport sector the introduction of alternative fuels-together with drastic energy efficiency gains-will be a key to sustainable mobility, nationally as well as globally. However, the future role of alternative fuels cannot be examined from the isolated perspective of the transport sector. Interactions with the energy system as a whole have to be taken into account. This holds both for the issue of availability of energy sources as well as for allocation effects, resulting from the shift of renewable energy from the stationary sector to mobile applications. With emphasis on hydrogen as a transport fuel for private passenger cars, this paper discusses the energy systems impacts of various scenarios introducing hydrogen fueled vehicles in Germany. It identifies clear restrictions to an enhanced growth of clean hydrogen production from renewable energy sources (RES). Furthermore, it points at systems interdependencies that call for a priority use of RES electricity in stationary applications. Whereas hydrogen can play an increasing role in transport after 2030 the most important challenge is to exploit short-mid-term potentials of boosting car efficiency

Diatoms: a fossil fuel of the future.

Science.gov (United States)

Levitan, Orly; Dinamarca, Jorge; Hochman, Gal; Falkowski, Paul G

2014-03-01

Long-term global climate change, caused by burning petroleum and other fossil fuels, has motivated an urgent need to develop renewable, carbon-neutral, economically viable alternatives to displace petroleum using existing infrastructure. Algal feedstocks are promising candidate replacements as a 'drop-in' fuel. Here, we focus on a specific algal taxon, diatoms, to become the fossil fuel of the future. We summarize past attempts to obtain suitable diatom strains, propose future directions for their genetic manipulation, and offer biotechnological pathways to improve yield. We calculate that the yields obtained by using diatoms as a production platform are theoretically sufficient to satisfy the total oil consumption of the US, using between 3 and 5% of its land area. Copyright © 2014 Elsevier Ltd. All rights reserved.

Preliminary estimates of the impacts of alternative spent fuel acceptance rates

International Nuclear Information System (INIS)

Clark, L.L.; McKee, R.W.; Short, S.M.

1986-02-01

The rate at which spent fuel is accepted by the federal waste management system is an important interface between the private nuclear power sector and the federal government, which will assume responsibility for spent fuel disposal. An analysis of alternative rates based on minimum age criteria indicates substantial incentives to limit acceptance rates so as to result in minimum 10 to 15 year fuel ages for repository acceptance [1500 to 2500 metric tons of uranium (MTU) per year]. These incentives include lower heat generation rates and systems costs

49 CFR 525.11 - Termination of exemption; amendment of alternative average fuel economy standard.

Science.gov (United States)

2010-10-01

... average fuel economy standard. 525.11 Section 525.11 Transportation Other Regulations Relating to... EXEMPTIONS FROM AVERAGE FUEL ECONOMY STANDARDS § 525.11 Termination of exemption; amendment of alternative average fuel economy standard. (a) Any exemption granted under this part for an affected model year does...

Development of alternate extractant systems for fast reactor fuel cycle

International Nuclear Information System (INIS)

Vasudeva Rao, P.R.; Suresh, A.; Venkatesan, K.A.; Srinivasan, T.G.; Raj, Baldev

2007-01-01

Due to the limitations of TBP in processing of high burn-up, Pu-rich fast reactor fuels, there is a need to develop alternate extractants for fast reactor fuel processing. In this context, our Centre has been examining the suitability of alternate tri-alkyl phosphates. Third phase formation in the extraction of Th(IV) by TBP, tri-n-amyl phosphate (TAP) and tri-2-methyl-butyl phosphate (T2MBP) from nitric acid media has been investigated under various conditions to derive conclusions on their application for extraction of Pu at macro levels. The chemical and radiolytic degradation of tri-n-amyl-phosphate (TAP) diluted in normal paraffin hydrocarbon (NPH) in the presence of nitric acid has been investigated by the measurement of plutonium retention in organic phase. The potential application of room temperature ionic liquids (RTILs) for reprocessing of spent nuclear fuel has been explored. Extraction of uranium (VI) and palladium (II) from nitric acid medium by commercially available RTIL and tri-n-butyl phosphate solution in RTIL have been studied and the feasibility of electrodeposition of uranium as uranium oxide (UO 2 ) and palladium (II) as metallic palladium from the loaded organic phase have been demonstrated. This paper describes results of the above studies and discusses the suitability of the systems for fast reactor fuel reprocessing. (authors)

Coronectomy - A viable alternative to prevent inferior alveolar nerve injury

Directory of Open Access Journals (Sweden)

Alok Sagtani

2015-12-01

Full Text Available Background and Objectives: Coronectomy is a relatively new method to prevent the risk of Inferior Alveolar Nerve (IAN injury during removal of lower third molars with limited scientific literature among Nepalese patients. Thus, a study was designed to evaluate coronectomy regarding its use, outcomes and complications.Materials and Methods: A descriptive study was conducted from December 2012 to December 2013 among patients attending Department of Oral and Maxillofacial Surgery, College of Dental Sciences, BP Koirala Institute of Health Sciences, Dharan, Nepal for removal of mandibular third molars. After reviewing the radiograph for proximity of third molar to the IAN, coronectomy was advised. A written informed consent was obtained from the patients and coronectomy was performed. Patients were recalled after one week. The outcome measures in the follow-up visit were primary healing, pain, infection, dry socket, root exposure and IAN injury. The prevalence of IAN proximity of lower third molars and incidence of complications were calculated.Results: A total 300 mandibular third molars were extracted in 278 patients during the study period. Out of 300 impacted mandibular third molar, 41 (13.7% showed close proximity to inferior alveolar nerve . The incidence of complications and failed procedure was 7.4% among the patients who underwent coronectomy. During the follow up visit, persistent pain and root exposure was reported while other complications like inferior alveolar nerve injury, dry socket and infection was not experienced by the study patients.Conclusion: With a success rate of 92.6% among the 41 patients, coronectomy is a viable alternative to conventional total extraction for mandibular third molars who have a higher risk for damage to the inferior alveolar nerve.JCMS Nepal. 2015;11(3:1-5.

Well-To-Wheel based fiscal systems. Can a WTW fiscal basis accelerate the introduction of alternative fuels?

International Nuclear Information System (INIS)

Van Bree, B.; Hanschke, C.B.

2011-09-01

This report explores to which extent alternative, (partially) Well-To-Wheel based fiscal systems may accelerate the introduction of low-carbon fuels and vehicles. The design of two alternative fiscal systems is described, as well as the challenges that any fiscal system must meet. The alternative systems are compared to the existing fiscal system with regard to (1) the extent to which they honour the 'polluter pays' principle, (2) the extent to which they are expected to accelerate the introduction of (alternative) gaseous fuels, liquid biofuels, and zero-emission vehicles, (3) their expected impact on the vehicle stock, and (4) a number of (undesired) side-effects. The results show that the alternative systems provide a stronger fiscal support for some alternative fuels and vehicles, but not for all.

Global warming and urban smog: Cost-effectiveness of CAFE standards and alternative fuels

International Nuclear Information System (INIS)

Krupnick, A.J.; Walls, M.A.; Collins, C.T.

1993-01-01

In this paper we estimate the cost-effectiveness, in terms of reducing greenhouse gas emissions, of increasing the corporate average fuel economy (CAFE) standard to 38 miles per gallon and substituting methanol, compressed natural gas (CNG), and reformulated gasoline for conventional gasoline. Greenhouse gas emissions are assessed over the entire fuel cycle and include carbon dioxide, methane, carbon monoxide, and nitrous oxide emissions. To account for joint environmental benefits, the cost per ton of greenhouse gas reduced is adjusted for reductions in volatile organic compound (VOC) emissions, an ozone precursor. CNG is found to be the most cost-effective of these alternatives, followed by increasing the CAFE standard, substituting methanol for gasoline, and substituting reformulated for conventional gasoline. Including the VOC benefits does not change the ranking of the alternatives, but does make the alternative fuels look better relative to increasing the CAFE standard. None of the alternatives look cost-effective should a carbon tax of $35 per ton be passed, and only CNG under optimistic assumptions looks cost-effective with a tax of $100 per ton of carbon. 35 refs., 4 figs., 6 tabs

Comparison of alternate fuels for aircraft. [liquid hydrogen, liquid methane, and synthetic aviation kerosene

Science.gov (United States)

Witcofski, R. D.

1979-01-01

Liquid hydrogen, liquid methane, and synthetic aviation kerosene were assessed as alternate fuels for aircraft in terms of cost, capital requirements, and energy resource utilization. Fuel transmission and airport storage and distribution facilities are considered. Environmental emissions and safety aspects of fuel selection are discussed and detailed descriptions of various fuel production and liquefaction processes are given. Technological deficiencies are identified.

Distributed renewable power from biomass and other waste fuels

Science.gov (United States)

Lyons, Chris

2012-03-01

The world population is continually growing and putting a burden on our fossil fuels. These fossil fuels such as coal, oil and natural gas are used for a variety of critical needs such as power production and transportation. While significant environmental improvements have been made, the uses of these fuels are still causing significant ecological impacts. Coal power production efficiency has not improved over the past thirty years and with relatively cheap petroleum cost, transportation mileage has not improved significantly either. With the demand for these fossil fuels increasing, ultimately price will also have to increase. This presentation will evaluate alternative power production methods using localized distributed generation from biomass, municipal solid waste and other waste sources of organic materials. The presentation will review various gasification processes that produce a synthetic gas that can be utilized as a fuel source in combustion turbines for clean and efficient combined heat and power. This fuel source can produce base load renewable power. In addition tail gases from the production of bio-diesel and methanol fuels can be used to produce renewable power. Being localized can reduce the need for long and costly transmission lines making the production of fuels and power from waste a viable alternative energy source for the future.

Multiple criteria decision making of alternative fuels for waste collection vehicles in southeast region of Serbia

Directory of Open Access Journals (Sweden)

Petrović Goran S.

2016-01-01

Full Text Available In this paper multiple criteria decision making approach of alternative fuels for waste collection vehicles in southeast region of Serbia was presented. Eight alternative fuels and advanced vehicle technologies were ranked according to thirteen criteria, including financial, socio-technical, and environmental. Assessment of alternatives was performed by using the weighted aggregated sum product assessment method and results were verified using multi-objective optimization on the basis of ratio analysis method. Considered criteria were obtained from previous researches and by assessment of professional experts from manufacturing industries, public utility companies, and academics institutions. The analysis showed that both biodiesel fuels - derived from used cooking oil or from vegetable oils are the best alternative fuels for Serbian waste collection vehicles in this point of time. Compressed natural gas-powered vehicles were also ranked high in this analysis, but due to the lack of financial capability for their purchase (especially in southeast region of Serbia, their gradual introduction into the waste collection fleet was proposed.

Solid fuel block as an alternate fuel for cooking and barbecuing: Preliminary results

International Nuclear Information System (INIS)

Sharma, Monikankana; Mukunda, H.S.; Sridhar, G.

2009-01-01

A large part of the rural people of developing countries use traditional biomass stoves to meet their cooking and heating energy demands. These stoves possess very low thermal efficiency; besides, most of them cannot handle agricultural wastes. Thus, there is a need to develop an alternate cooking contrivance which is simple, efficient and can handle a range of biomass including agricultural wastes. In this reported work, a highly densified solid fuel block using a range of low cost agro residues has been developed to meet the cooking and heating needs. A strategy was adopted to determine the best suitable raw materials, which was optimized in terms of cost and performance. Several experiments were conducted using solid fuel block which was manufactured using various raw materials in different proportions; it was found that fuel block composed of 40% biomass, 40% charcoal powder, 15% binder and 5% oxidizer fulfilled the requirement. Based on this finding, fuel blocks of two different configurations viz. cylindrical shape with single and multi-holes (3, 6, 9 and 13) were constructed and its performance was evaluated. For instance, the 13 hole solid fuel block met the requirement of domestic cooking; the mean thermal power was 1.6 kW th with a burn time of 1.5 h. Furthermore, the maximum thermal efficiency recorded for this particular design was 58%. Whereas, the power level of single hole solid fuel block was found to be lower but adequate for barbecue cooking application

Alternative Fuels Data Center: Mesa Unified School District Reaps Economic

Science.gov (United States)

and Environmental Benefits with Propane Buses Mesa Unified School District Reaps Economic and School District Reaps Economic and Environmental Benefits with Propane Buses on Facebook Tweet about Alternative Fuels Data Center: Mesa Unified School District Reaps Economic and Environmental Benefits with

75 FR 26121 - Regulation of Fuels and Fuel Additives: Alternative Affirmative Defense Requirements for Ultra...

Science.gov (United States)

2010-05-11

... standard at retail facilities. This alternative defense consists of a comprehensive program of quality... without change and may be made available online at http://www.regulations.gov , including any personal..., import, sell, store or transport ULSD highway diesel fuel to meet the standards specified in the diesel...

Biofuels: An Alternative to U.S. Air Force Petroleum Fuel Dependency

National Research Council Canada - National Science Library

Danigole, Mark S

2007-01-01

.... In conjunction with the President's mandate to reduce dependency on foreign procured oil and in an effort to stem unfunded fuel expenses, the USAF established an active alternative energy program...

Experimental evaluation of hybrid propulsion rocket engine operating with paraffin fuel grain and gaseous oxygen

OpenAIRE

Genivaldo Pimenta dos Santos

2014-01-01

In the last decade the hybrid propulsion has been considering as a viable alternative of chemical energy conversion stored in propellants into kinetic energy. This energy is applied in propulsive systems of manned platforms, maneuvering procedures and even in the repositioning process of micro satellites. It presents attractive features and good balance between performance and environmental impact. Paraffin based grains are the hybrid solid fuels appointed as polymeric fuel substitute. The li...

Alternative fuel cycle evaluation in the Federal Republic of Germany

International Nuclear Information System (INIS)

Papp, R.; Closs, K.D.

1986-01-01

In compliance with a 1979 governmental decision, Karlsruhe Nuclear Research Center managed the research and development (R and D) program ''Alternative Entsorgung,'' which had two major goals: (a) development of technical concepts for direct disposal of spent fuel and (b) comparison of the traditional back end of the nuclear fuel cycle based on fuel reprocessing with direct disposal. With respect to radiological safety, this comparison revealed that direct disposal scores better than the reprocessing path, but the difference is judged minor when compared to doses from natural radiation background. From the standpoint of cost, direct disposal proves more economical by a margin of 30% even though the reference system of direct disposal was not cost optimized. Finally, some unresolved but not unresolvable issues exist with regard to safeguarding a repository for spent fuel. In its decision in January 1985, the government of the Federal Republic of Germany stated that the results of the R and D program indicated that the legal requirement to ensure Entsorgung were better fulfilled by fuel reprocessing than by direct disposal of spent fuel

Liquid alternative diesel fuels with high hydrogen content

Energy Technology Data Exchange (ETDEWEB)

Hancsok, Jenoe; Varga, Zoltan; Eller, Zoltan; Poelczmann, Gyoergy [Pannonia Univ., Veszprem (Hungary). MOL Dept. of Hydrocarbon Processing; Kasza, Tamas [MOL Hungarian Oil and Gas Plc., Szazhalombatta (Hungary)

2013-06-01

Mobility is a keystone of the sustainable development. In the operation of the vehicles as the tools of mobility internal combustion engines, so thus Diesel engines will play a remarkable role in the next decades. Beside fossil fuels - used for power these engines - liquid alternative fuels have higher and higher importance, because of their known advantages. During the presentation the categorization possibilities based on the chronology of their development and application will be presented. The importance of fuels with high hydrogen content will be reviewed. Research and development activity in the field of such kind of fuels will be presented. During this developed catalytic systems and main performance properties of the product will be presented which were obtained in case of biogasoils produced by special hydrocracking of natural triglycerides and in case of necessity followed by isomerization; furthermore in case of synthetic biogasoils obtained by the isomerization hydrocracking of Fischer-Tropsch paraffins produced from biomass based synthesis gas. Excellent combustion properties (cetane number > 65-75), good cold flow properties and reduced harmful material emission due to the high hydrogen content (C{sub n}H{sub 2n+2}) are highlighted. Finally production possibilities of linear and branched paraffins based on lignocelluloses are briefly reviewed. Summarizing it was concluded that liquid hydrocarbons with high isoparaffin content are the most suitable fuels regarding availability, economical and environmental aspects, namely the sustainable development. (orig.)

Southern Nevada Alternative Fuels Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Hyde, Dan; Fast, Matthew

2009-12-31

The Southern Nevada Alternative Fuels Program is designed to demonstrate, in a day-to-day bus operation, the reliability and efficiency of a hydrogen bus operation under extreme conditions. By using ICE technology and utilizing a virtually emission free fuel, benefits to be derived include air quality enhancement and vehicle performance improvements from domestically produced, renewable energy sources. The project objective is to help both Ford and the City demonstrate and evaluate the performance characteristics of the E-450 H2ICE shuttle buses developed by Ford, which use a 6.8-liter supercharged Triton V-10 engine with a hydrogen storage system equivalent to 29 gallons of gasoline. The technology used during the demonstration project in the Ford buses is a modified internal combustion engine that allows the vehicles to run on 100% hydrogen fuel. Hydrogen gives a more thorough fuel burn which results in more power and responsiveness and less pollution. The resultant emissions from the tailpipe are 2010 Phase II compliant with NO after treatment. The City will lease two of these E-450 H2ICE buses from Ford for two years. The buses are outfitted with additional equipment used to gather information needed for the evaluation. Performance, reliability, safety, efficiency, and rider comments data will be collected. The method of data collection will be both electronically and manually. Emissions readings were not obtained during the project. The City planned to measure the vehicle exhaust with an emissions analyzer machine but discovered the bus emission levels were below the capability of their machine. Passenger comments were solicited on the survey cards. The majority of comments were favorable. The controllable issues encountered during this demonstration project were mainly due to the size of the hydrogen fuel tanks at the site and the amount of fuel that could be dispensed during a specified period of time. The uncontrollable issues encountered during this

Greenhouse gas emissions from the production and use of alternative transport fuels

International Nuclear Information System (INIS)

Le Cornu, J.K.

1990-01-01

A number of the commonly proposed alternative transport fuels were ranked according to both the cumulative greenhouse gas emissions and the production costs incurred between the recovery of the prime resource and the fuel's end use by the Australian transport fleet. An examination of the emissions of each greenhouse gas at each production stage confirmed the common presumption that the low levels of secondary greenhouse gas emissions involved contribute little to the overall greenhouse impact of a fuel's production and use. From a greenhouse point of view the transport fuels studied could be reasonable well ranked by considering their carbon dioxide emissions alone. A possible exception may apply in the case of the compressed natural gas option, which may need to separate consideration of the effect of fugitive emissions of methane from gas distribution systems. An assumption involved in reaching this result was that nitrous oxide emissions, on which there was inadequate hard data, would not form more than 1% of the total nitrogen oxide emissions. At such an emission level it could contribute up to 5% of a fuel's total greenhouse impact. It is concluded that apart from some small niche opportunities, there is no Australian alternative transport fuel option whose production cost and greenhouse impact makes it one which policy should favour over other fuels. It is stressed that this is no more than a preliminary scouting study of generic options, which addresses only greenhouse issues. 17 refs., 1 tab., 8 figs

Some alternatives to the mixed oxide fuel cycle

International Nuclear Information System (INIS)

Deonigi, D.E.; Eschbach, E.A.; Goldsmith, S.; Pankaskie, P.J.; Rohrmann, C.A.; Widrig, R.D.

1977-02-01

While on initial examination each of the six fuel cycle concepts (tandem cycle, extended burnup, fuel rejuvenation, coprocessing, partial reprocessing, and thorium) described in the report may have some potential for improving safeguards, none of the six appears to have any other major or compelling advantages over the mixed oxide (MOX) fuel cycle. Compared to the MOX cycle, all but coprocessing appear to have major disadvantages, including severe cost penalties. Three of the concepts-tandem, extended burnup, and rejuvenation--share the basic problems of the throwaway cycle (GESMO Alternative 6): without reprocessing, high-level waste volumes and costs are substantially increased, and overall uranium utilization decreases for three reasons. First, the parasitic fission products left in the fuel absorb neutrons in later irradiation steps reducing the overall neutronic efficiencies of these cycles. Second, discarded fuel still has sufficient fissile values to warrant recycle. Third, perhaps most important, the plutonium needed for breeder start-up will not be available; without the breeder, uranium utilization would drop by about a factor of sixty. Two of the concepts--coprocessing and partial reprocessing--involve variations of the basic MOX fuel cycle's chemical reprocessing step to make plutonium diversion potentially more difficult. These concepts could be used with the MOX fuel cycle or in conjunction with the tandem, extended burnup and rejuvenation concepts to eliminate some of the problems with those cycles. But in so doing, the basic impetus for those cycles--elimination of reprocessing for safeguards purposes--no longer exists. Of all the concepts considered, only coprocessing--and particularly the ''master blend'' version--appears to have sufficient promise to warrant a more detailed study. The master blend concept could possibly make plutonium diversion more difficult with minimal impact on the reprocessing and MOX fuel fabrication operations

Performance of a small-scale turbojet engine fed with traditional and alternative fuels

International Nuclear Information System (INIS)

Badami, M.; Nuccio, P.; Pastrone, D.; Signoretto, A.

2014-01-01

Highlights: • One synthetic fuel, one bio-fuel blend and one traditional kerosene were tested on a small-scale turbojet. • The three fuels were characterized and their chemical and physical specifications were compared. • The experimental results, in term of CO, UHC and NO x emissions, are discussed. • Emissions are compared with CFD analysis and semi-empirical equations found in literature. - Abstract: The growing use of aeronautical fuels, together with the increasing attention towards reduced environmental impact technologies, are driving governments and aeronautical companies to search for alternative aeronautical fuels to petroleum based kerosene. Analysis and measurements on real aeronautical turbines are complex and expensive; for this reason the use of parts of real engines or small size turbojets can be very interesting for research activities. The present paper describes the results of an experimental and numerical activity, regarding the influence of alternative fuels on the performance in term of emissions, on a small-scale turbojet engine with a nominal thrust of 80 N at 80,000 rpm. Three different fuels, a traditional Jet-A kerosene, a synthetic Gas To Liquid (GTL) fuel and a blend of 30% Jatropha Methyl Ester (JME) and 70% Jet-A, were tested. The experimental results, in term of CO, UHC and NO x emissions, are discussed and compared with results obtained from CFD analysis and from semi-empirical equations found in literature

Alternative bipolar plates design and manufacturing for PEM fuel cell

International Nuclear Information System (INIS)

Lee Chang Chuan; Norhamidi Muhamad; Jaafar Sahari

2006-01-01

Bipolar plates is one of the important components in fuel cell stack, it comprise up to 80% of the stack volume. Traditionally, these plates have been fabricated from graphite, owing to its chemical nobility, and high electrical and thermal conductivity; but these plates are brittle and relatively thick. Therefore increasing the stack volume and size. Alternatives to graphite are carbon-carbon composite, carbon-polymer composite and metal (aluminum, stainless steel, titanium and nickel based alloy). The use of coated and uncoated metal bipolar plates has received attention recently due to the simplicity of plate manufacturing. The thin nature of the metal substrate allows for smaller stack design with reduced weight. Lightweight coated metals as alternative to graphite plate is being developed. Beside the traditional method of machining and slurry molding, metal foam for bipolar plates fabrication seems to be a good alternative. The plates will be produced with titanium powder by Powder Metallurgy method using space holders technique to produce the meal foam flow-field. This work intends to facilitate the materials and manufacturing process requirements to produce cost effective foamed bipolar plates for fuel cell

Are We There Yet? Alternative Fuels for School Buses

Science.gov (United States)

Lea, Dennis; Carter, Deborah

2009-01-01

America's annual oil consumption continues to increase and is projected to continue the upward spiral into the foreseeable future. Alternative-fuel options are available that are not only cheaper in some cases on an energy-equivalent basis but are also more environmentally friendly. Education leaders need to be concerned with both these facts.…

Alternative Fuels Data Center: Yellowstone National Park Commits to

Science.gov (United States)

Alternative Fuels Sept. 16, 2017 Photo of a truck Phoenix Utility Fleet Drives Smarter with Biodiesel Aug. 26 Cooking Oil Powers Biodiesel Vehicles in Rhode Island July 14, 2017 Photo of a truck Idaho Transports Mail Home Runs on Biodiesel in North Carolina June 9, 2017 Photo of a bus New Hampshire Cleans up with

Baseline energy forecasts and analysis of alternative strategies for airline fuel conservation

Energy Technology Data Exchange (ETDEWEB)

1976-07-01

To evaluate the impact of fuel conservation strategies, baseline forecasts of airline activity and energy consumption to 1990 were developed. Alternative policy options to reduce fuel consumption were identified and analyzed for three baseline levels of aviation activity within the framework of an aviation activity/energy consumption model. By combining the identified policy options, a strategy was developed to provide incentives for airline fuel conservation. Strategies and policy options were evaluated in terms of their impact on airline fuel conservation and the functioning of the airline industry as well as the associated social, environmental, and economic costs. (GRA)

Bovine meat and bone meal is an economically viable alternative in quail feeding in the initial phase

Directory of Open Access Journals (Sweden)

Carla C. Pizzolante

2016-06-01

Full Text Available Quail egg production has experienced a steep rise in the last decade. Nutrition is the main factor affecting productive potential in the poultry industry, as appropriate nutritional management is necessary to ensure the maintenance of optimal physical conditions, growth and the production of high quality products. Meat and bone meal (MBM has often been used in the poultry industry as an alternative and cost-effective source of protein in partial replacement of corn and soybean meal. However, there have been no studies to date that have investigated the effect of dietary MBM on the performance of quail or on the costs of production in the starter phase. This is particularly important considering that this phase is characterized by large investments by producers, without immediate economic return. In this study, we investigated whether partial replacement of soybean meal (SBM by meat and bone meal (MBM in the diet of Japanese quail during the starter phase is a viable alternative that would maintain or improve their productive and economic performance. Our results show that the inclusion of MBM in the diet of quail reduces feeding costs by up to 6% without impairing productive performance.

Bovine meat and bone meal is an economically viable alternative in quail feeding in the initial phase.

Science.gov (United States)

Pizzolante, Carla C; Kakimoto, Sérgio K; Moraes, José E; Saccomani, Ana Paula O; Soares, Daniela F; Paschoalin, Gustavo C; Budiño, Fábio E L

2016-05-31

Quail egg production has experienced a steep rise in the last decade. Nutrition is the main factor affecting productive potential in the poultry industry, as appropriate nutritional management is necessary to ensure the maintenance of optimal physical conditions, growth and the production of high quality products. Meat and bone meal (MBM) has often been used in the poultry industry as an alternative and cost-effective source of protein in partial replacement of corn and soybean meal. However, there have been no studies to date that have investigated the effect of dietary MBM on the performance of quail or on the costs of production in the starter phase. This is particularly important considering that this phase is characterized by large investments by producers, without immediate economic return. In this study, we investigated whether partial replacement of soybean meal (SBM) by meat and bone meal (MBM) in the diet of Japanese quail during the starter phase is a viable alternative that would maintain or improve their productive and economic performance. Our results show that the inclusion of MBM in the diet of quail reduces feeding costs by up to 6% without impairing productive performance.

10 CFR 503.32 - Lack of alternate fuel supply at a cost which does not substantially exceed the cost of using...

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Lack of alternate fuel supply at a cost which does not... (CONTINUED) ALTERNATE FUELS NEW FACILITIES Permanent Exemptions for New Facilities § 503.32 Lack of alternate... alternate fuel supply at a cost which does not substantially exceed the cost of using imported petroleum. To...

Alternative Fuels Data Center: New Mexico Transportation Data for

Science.gov (United States)

to alternative fuels and advanced vehicles Recent Additions and Updates Biodiesel Blend Mandate Public Private Biodiesel (B20 and above) 1 4 Compressed Natural Gas (CNG) 8 3 Electric 59 4 Ethanol (E85 GGE Biodiesel (B20) $2.60/gallon $2.37/GGE $2.84/gallon $2.58/GGE Biodiesel (B99-B100) $2.49/gallon

Alternative Fuels Data Center: Federal Laws and Incentives for Biodiesel

Science.gov (United States)

SmartWay Transport Partnership is a market-based public-private collaboration between the U.S operate vehicle fleets, the public, and other interested entities about the benefits of biodiesel use Biodiesel Printable Version Share this resource Send a link to Alternative Fuels Data Center

Alternative calcination development status report

International Nuclear Information System (INIS)

Boardman, R.D.

1997-12-01

The Programmatic Spent Nuclear Fuel and (INEEL) Environmental Restoration and Waste Management Programs Environmental Impact Statement Record of Decision, dated June 1, 1995, specifies that high-level waste stored in the underground tanks at the ICPP continue to be calcined while other options to treat the waste are studied. Therefore, the High-Level Waste Program has funded a program to develop new flowsheets to increase the liquid waste processing rate. Simultaneously, a radionuclide separation process, as well as other options, are also being developed, which will be compared to the calcination treatment option. Two alternatives emerged as viable candidates; (1) elevated temperature calcination (also referred to as high temperature calcination), and (2) sugar-additive calcination. Both alternatives were determined to be viable through testing performed in a lab-scale calcination mockup. Subsequently, 10-cm Calciner Pilot Plant scoping tests were successfully completed for both flowsheets. The results were compared to the standard 500 C, high-ANN flow sheet (baseline flowsheet). The product and effluent streams were characterized to help elucidate the process chemistry and to investigate potential environmental permitting issues. Several supplementary tests were conducted to gain a better understanding of fine-particles generation, calcine hydration, scrub foaming, feed makeup procedures, sugar/organic elimination, and safety-related issues. Many of the experiments are only considered to be scoping tests, and follow-up experiments will be required to establish a more definitive understanding of the flowsheets. However, the combined results support the general conclusion that flowsheet improvements for the NWCF are technically viable

Environmental impact of alternative fuel on Tehran air pollution

International Nuclear Information System (INIS)

Ebtekar, T.

1995-01-01

Seventy percent of the air pollution in the city of Tehran stems from mobile sources, and in comparison with other major cities of the world, Iran's capital experiences one of the most polluted metropolitan areas. There exists a surplus of liquid petroleum gas (LPG) in the Persian Gulf and Iranian market, in addition, Iran possesses the second largest reservoir of natural gas in the world. These alternative energy resources create a favorable potential fuel for city of Tehran. Experiments carried out in Tehran indicate that in converting the taxis from gasoline to a dual fuel (LPG/gasoline) car or to a dual fuel natural gas vehicle (NGV) reduce all major pollutants (CO, HC, NOX, Pb) substantially. Following the author's recommendation, the number of LPG dispensing units in gas stations are increasing and the number of dual fuel taxis amount to several thousands in the metropolitan area. The conversion of diesel buses in the Tehran Public Transportation Corporation to natural gas (NGV) has been recommended by the author and vast experimental works are underway at the present time

KHD combustion chamber. Flexible use of alternative fuels in the cement plant; KHD Brennkammer. Flexibler Einsatz von alternativen Brennstoffen im Zementwerk

Energy Technology Data Exchange (ETDEWEB)

Schuermann, Heiko [Humboldt Wedag GmbH, Koeln (Germany)

2012-07-01

In many parts of the world, the use of alternative fuels is a recognized measure for reducing the CO{sub 2} emissions that result from burning primary fuels such as coal, oil and natural gas. Alternative or secondary fuels are the terms used for combustible residues from industrial and commercial manufacturing processes, agricultural production, and sorted municipal refuse. Due to the wide range of possible sources of alternative fuels, there is very great variation in their energy content, ash, moisture content, particle size, form, density etc., so there is no patent solution for their use in a cement plant. For proper operation of the rotary kiln, it is particularly important to use alternative fuel qualities that have good heat value and reactivity in order to achieve a stable, hot sintering zone and to completely burnout the highest possible amount of the fuel while it is suspended in the air stream. Combustion in the calciner places fewer demands on the properties of the alternative fuels than combustion in the rotary kiln burner does. This means that the calciner is the ideal combustion point for the usage of alternative fuels. To enable maximum possible flexibility for the combustion of widely differing alternative fuels in the calciner, KHD Humboldt Wedag offers the option of installing a combustion chamber in the modular PYROCLON calciner system. Due to the operating characteristics of this combustion chamber, which are described in the following sections of this article, even alternative fuels with low heat values and a low degree of preparation can be safely and completely burnt. (orig.)

Preliminary Evaluation of Alternate Designs for HFIR Low-Enriched Uranium Fuel

Energy Technology Data Exchange (ETDEWEB)

Renfro, David [ORNL; Chandler, David [ORNL; Cook, David [ORNL; Ilas, Germina [ORNL; Jain, Prashant [ORNL; Valentine, Jennifer [ORNL

2014-10-30

Engineering design studies of the feasibility of conversion of the High Flux Isotope Reactor (HFIR) from high-enriched uranium (HEU) to low-enriched uranium (LEU) fuel are ongoing at Oak Ridge National Laboratory (ORNL) as part of an effort sponsored by the U.S. Department of Energy’s Global Threat Reduction Initiative (GTRI)/Reduced Enrichment for Research and Test Reactors (RERTR) program. The fuel type selected by the program for the conversion of the five high-power research reactors in the U.S. that still use HEU fuel is a new U-Mo monolithic fuel. Studies by ORNL have previously indicated that HFIR can be successfully converted using the new fuel provided (1) the reactor power can be increased from 85 MW to 100 MW and (2) the fuel can be fabricated to a specific reference design. Fabrication techniques for the new fuel are under development by the program but are still immature, especially for the “complex” aspects of the HFIR fuel design. In FY 2012, the program underwent a major shift in focus to emphasize developing and qualifying processes for the fabrication of reliable and affordable LEU fuel. In support of this new focus and in an effort to ensure that the HFIR fuel design is as suitable for reliable fabrication as possible, ORNL undertook the present study to propose and evaluate several alternative design features. These features include (1) eliminating the fuel zone axial contouring in the previous reference design by substituting a permanent neutron absorber in the lower unfueled region of all of the fuel plates, (2) relocating the burnable neutron absorber from the fuel plates of the inner fuel element to the side plates of the inner fuel element (the fuel plates of the outer fuel element do not contain a burnable absorber), (3) relocating the fuel zone inside the fuel plate to be centered on the centerline of the depth of the plate, and (4) reshaping the radial contour of the relocated fuel zone to be symmetric about this centerline. The

Preliminary Evaluation of Alternate Designs for HFIR Low-Enriched Uranium Fuel

Energy Technology Data Exchange (ETDEWEB)

Renfro, David G [ORNL; Chandler, David [ORNL; Cook, David Howard [ORNL; Ilas, Germina [ORNL; Jain, Prashant K [ORNL; Valentine, Jennifer R [ORNL

2014-11-01

Engineering design studies of the feasibility of conversion of the High Flux Isotope Reactor (HFIR) from high-enriched uranium (HEU) to low-enriched uranium (LEU) fuel are ongoing at Oak Ridge National Laboratory (ORNL) as part of an effort sponsored by the U.S. Department of Energy s Global Threat Reduction Initiative (GTRI)/Reduced Enrichment for Research and Test Reactors (RERTR) program. The fuel type selected by the program for the conversion of the five high-power research reactors in the U.S. that still use HEU fuel is a new U-Mo monolithic fuel. Studies by ORNL have previously indicated that HFIR can be successfully converted using the new fuel provided (1) the reactor power can be increased from 85 MW to 100 MW and (2) the fuel can be fabricated to a specific reference design. Fabrication techniques for the new fuel are under development by the program but are still immature, especially for the complex aspects of the HFIR fuel design. In FY 2012, the program underwent a major shift in focus to emphasize developing and qualifying processes for the fabrication of reliable and affordable LEU fuel. In support of this new focus and in an effort to ensure that the HFIR fuel design is as suitable for reliable fabrication as possible, ORNL undertook the present study to propose and evaluate several alternative design features. These features include (1) eliminating the fuel zone axial contouring in the previous reference design by substituting a permanent neutron absorber in the lower unfueled region of all of the fuel plates, (2) relocating the burnable neutron absorber from the fuel plates of the inner fuel element to the side plates of the inner fuel element (the fuel plates of the outer fuel element do not contain a burnable absorber), (3) relocating the fuel zone inside the fuel plate to be centered on the centerline of the depth of the plate, and (4) reshaping the radial contour of the relocated fuel zone to be symmetric about this centerline. The present

An alternative transportation fuels update : a case study of the developing E85 industry.

Science.gov (United States)

2011-10-01

As the United States imports more than half of its oil and overall consumption continues to climb, : the 1992 Energy Policy Act established the goal of having alternative fuels replace at least ten : percent of petroleum fuels used in the trans...

Determination of heating value of industrial waste for the formulation of alternative fuels

Directory of Open Access Journals (Sweden)

Bouabid G.

2013-09-01

Full Text Available The use of alternative fuels has become increasingly widespread. They are basically designed based on industrial waste so that they can substitute fossil fuels which start to become scarce. Alternative fuels must meet some criteria, namely an important calorific content, minimum humidity and ash content. When it comes to combustion, the most interesting parameter is the calorific value which represents the thermal energy released during combustion. The experiments that were conducted showed that the calorific value is influenced by other parameters namely moisture and ash content. It was therefore necessary to study the behavior of the heating value in terms of these two parameters in order to establish a relationship that is used to describe the behavior. This is expected to allow a simulation of the calorific value of a mixture of various industrial waste.

Tiger Teams Technical Assistance: Reliable, Universal Open Architecture for Card Access to Dispense Alternative Fuels

Energy Technology Data Exchange (ETDEWEB)