WorldWideScience

Sample records for vi ion sorption

  1. Sorption of uranium(VI) using oxime-grafted ordered mesoporous carbon CMK-5

    Energy Technology Data Exchange (ETDEWEB)

    Tian Gan; Geng Junxia; Jin Yongdong; Wang Chunli; Li Shuqiong; Chen Zhen; Wang Hang; Zhao Yongsheng [College of Chemistry, Sichuan University, Chengdu 610064 (China); Li Shoujian, E-mail: sjli000616@scu.edu.cn [College of Chemistry, Sichuan University, Chengdu 610064 (China)

    2011-06-15

    A new sorbent for uranium(VI) has been developed by functionalizing ordered mesoporous carbon CMK-5 with 4-acetophenone oxime via thermally initiated diazotization. The sorption of U(VI) ions onto the functionalized CMK-5 (Oxime-CMK-5) was investigated as a function of sorbent dosage, pH value, contact time, ionic strength and temperature using batch sorption techniques. The results showed that U(VI) sorption onto Oxime-CMK-5 was strongly dependent on pH, but to a lesser extent, on ionic strength. Kinetic studies revealed that the sorption process achieved equilibrium within 30 min and followed a pseudo-first-order rate equation. The isothermal data correlated with the Langmuir model better than the Freundlich model. Thermodynamic data indicated the spontaneous and endothermic nature of the process. Under current experimental conditions, a maximum U(VI) sorption capacity was found to be 65.18 mg/g. Quantitative recovery of uranium was achieved by desorbing the U(VI)-loaded Oxime-CMK-5 with 1.0 mol/L HCl and no significant decrease in U(VI) sorption capability of Oxime-CMK-5 was observed after five consecutive sorption-desorption cycles. The sorption study performed in a simulated nuclear industry effluent demonstrated that the new sorbent showed a desirable selectivity for U(VI) ions over a range of competing metal ions.

  2. U(VI) and Eu(III) ion sorption in the interface solution-phosphate solids: Structural study and mechanisms; Sorption des ions U(VI) et Eu(III) a l`interface solution - solides phosphates: Etude structurale et mechanismes

    Energy Technology Data Exchange (ETDEWEB)

    Drot, Romuald [Inst. de Physique Nucleaire, Paris-11 Univ., 91 - Orsay (France)

    1998-09-18

    As part of the storage of nuclear wastes in a deep underground disposal, radionuclides sorption on geological or engineered barriers is one of the most important factor which could enhance retardation. Thus, the knowledge of such mechanisms is needed. For this purpose, we chose to experimentally define sorption equilibria before performing simulation of retention data. Several phosphate compounds are potential candidates as engineered barrier additives. We considered Th{sub 4}(PO{sub 4}){sub 4}P{sub 2}O{sub 7}, Zr{sub 2}O(PO{sub 4}){sub 2} which allow to study the effect of PO{sub 4} and P{sub 2}O{sub 7} groups separately. Eu(III) and U(IV) ions were used as structural probes in order to simulate actinides (III) and (VI) behavior. X-ray powder diffraction, IR spectroscopy and electron probe microanalysis were used to characterized the synthesized solids. Electrophoretic measurements showed an amphoteric behavior of surface sites. Moreover, laser spectro-fluorimetry experiments indicated that no diffusion phenomena of the sorbed ion inside the solid occurs. Thus, we considered that a surface complexation model should be applied. Laser spectro-fluorimetry and XPS allowed to determine the nature of surface sites. ZrP{sub 2}O{sub 7} presents only one single site (P{sub 2}O{sub 7} groups) whereas Th{sub 4}(PO{sub 4}){sub 4}P{sub 2}O{sub 7} and Zr{sub 2}O(PO{sub 4}){sub 2} admit two types of sites (PO{sub 4}/P{sub 2}O{sub 7} and PO{sub 4}/oxo groups, respectively). Sorbed species were identified using laser spectro-fluorimetry which indicate that, in KNO{sub 3} 0.5 M medium and for a known surface site, there are two surface complexes for U(VI) (sorption of UO{sup 2+}{sub 2} et de UO{sub 2}NO{sup +}{sub 3} species) and only one for Eu(III) (sorption of EuNO{sup 2+}{sub 3}). They are linked to the substrate as bidentate inner sphere complexes (EXAFS study). Surface acidity constants were determined by simulation of potentiometric titration curves obtained for each solid

  3. Sorption of Uranium(VI and Thorium(IV by Jordanian Bentonite

    Directory of Open Access Journals (Sweden)

    Fawwaz I. Khalili

    2013-01-01

    Full Text Available Purification of raw bentonite was done to remove quartz. This includes mixing the raw bentonite with water and then centrifuge it at 750 rpm; this process is repeated until white purified bentonite is obtained. XRD, XRF, FTIR, and SEM techniques will be used for the characterization of purified bentonite. The sorption behavior of purified Jordanian bentonite towards and Th4+ metal ions in aqueous solutions was studied by batch experiment as a function of pH, contact time, temperature, and column techniques at 25.0∘C and . The highest rate of metal ions uptake was observed after 18 h of shaking, and the uptake has increased with increasing pH and reached a maximum at . Bentonite has shown high metal ion uptake capacity toward uranium(VI than thorium(IV. Sorption data were evaluated according to the pseudo- second-order reaction kinetic. Sorption isotherms were studied at temperatures 25.0∘C, 35.0∘C, and 45.0∘C. The Langmuir, Freundlich, and Dubinin-Radushkevich (D-R sorption models equations were applied and the proper constants were derived. It was found that the sorption process is enthalpy driven for uranium(VI and thorium(IV. Recovery of uranium(VI and thorium(IV ions after sorption was carried out by treatment of the loaded bentonite with different concentrations of HNO3 1.0 M, 0.5 M, 0.1 M, and 0.01 M. The best percent recovery for uranium(VI and thorium(IV was obtained when 1.0 M HNO3 was used.

  4. Uranium (Vi) sorption onto zirconium diphosphate chemically modified

    Energy Technology Data Exchange (ETDEWEB)

    Garcia G, N. [Universidad Autonoma del Estado de Mexico, Facultad de Quimica, Paseo Tollocan esquina Paseo Colon s/n, Toluca 50120, Estado de Mexico (Mexico); Ordonez R, E., E-mail: nidgg@yahoo.com.m [ININ, Carretera Mexico-Toluca s/n, Ocoyoacac 52750, Estado de Mexico (Mexico)

    2010-10-15

    This work deals with the uranium (Vi) speciation after sorption onto zirconium diphosphate (ZrP{sub 2}O{sub 7}) surface, hydrated and in a surface modified with organic acids. Oxalic and citric acids were chosen to modify the ZrP{sub 2}O{sub 7} surface because they have poly carboxylic groups and they mimic the organic matter in nature. Thus the interest of this work is to evaluate the uranium (Vi) sorption edge at different s ph values in natural and modified surfaces. The luminescence technique (fluorescence and phosphorescence, respectively) was used for the quantification and speciation of uranyl sorbed at the zirconium diphosphate interface. The fluorescence experiment, showed that adsorption of uranyl on surface of zirconium diphosphate tends to 100%. The speciation shows that there are different complexes in surface which were formed between zirconium diphosphate and uranyl, since it is produced a displacement of wavelength in fluorescence spectra of each system. (Author)

  5. Characterization of uranium(VI) sorption by organobentonite

    Energy Technology Data Exchange (ETDEWEB)

    Majdan, Marek, E-mail: marek.jerzy@poczta.umcs.lublin.pl [Faculty of Chemistry, Maria Curie Sklodowska University, 20-031 Lublin (Poland); Pikus, Stanislaw; Gajowiak, Agnieszka; Gladysz-Plaska, Agnieszka [Faculty of Chemistry, Maria Curie Sklodowska University, 20-031 Lublin (Poland); Krzyzanowska, Halina; Zuk, Jerzy [Institute of Physics, Maria Curie Sklodowska University, 20-031 Lublin (Poland); Bujacka, Monika [Faculty of Chemistry, Maria Curie Sklodowska University, 20-031 Lublin (Poland)

    2010-06-15

    The U(VI) sorption on the bentonite modified by hexadecyltrimethylammonium bromide (HDTMA) was studied in the concentration range: 0.0001-0.001 mol/dm{sup 3} in the aqueous phase and in the pH range: 3-10. The experiments concerning the pH influence on the molar absorption coefficient c{sub b} of U(VI) in the bentonite phase showed that the species: UO{sub 2}{sup 2+}, UO{sub 2}(OH){sup +}, UO{sub 2}(OH){sub 2} UO{sub 2}(OH){sub 3}{sup -}, UO{sub 2}(OH){sub 4}{sup 2-}, (UO{sub 2}){sub 3}(OH){sub 5}{sup +}, (UO{sub 2}){sub 3}(OH){sub 7}{sup -}, present in the aqueous phase, are responsible for uranium sorption. Their sorption parameters K were determined and it is evident that for higher concentrations of HDTMA{sup +} cations in the bentonite phase, i.e. for b96-b157 bentonite, the presence of anionic species: UO{sub 2}(OH){sub 3}{sup -}, UO{sub 2}(OH){sub 4}{sup 2-}, and (UO{sub 2}){sub 3}(OH){sub 7}{sup -} in the aqueous phase results in the increase of U(VI) molar absorption coefficient c{sub b} in the sorbent phase.

  6. New approach in modeling Cr(VI) sorption onto biomass from metal binary mixtures solutions

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chang [College of Environmental Science and Engineering, Anhui Normal University, South Jiuhua Road, 189, 241002 Wuhu (China); Chemical Engineering Department, Escola Politècnica Superior, Universitat de Girona, Ma Aurèlia Capmany, 61, 17071 Girona (Spain); Fiol, Núria [Chemical Engineering Department, Escola Politècnica Superior, Universitat de Girona, Ma Aurèlia Capmany, 61, 17071 Girona (Spain); Villaescusa, Isabel, E-mail: Isabel.Villaescusa@udg.edu [Chemical Engineering Department, Escola Politècnica Superior, Universitat de Girona, Ma Aurèlia Capmany, 61, 17071 Girona (Spain); Poch, Jordi [Applied Mathematics Department, Escola Politècnica Superior, Universitat de Girona, Ma Aurèlia Capmany, 61, 17071 Girona (Spain)

    2016-01-15

    In the last decades Cr(VI) sorption equilibrium and kinetic studies have been carried out using several types of biomasses. However there are few researchers that consider all the simultaneous processes that take place during Cr(VI) sorption (i.e., sorption/reduction of Cr(VI) and simultaneous formation and binding of reduced Cr(III)) when formulating a model that describes the overall sorption process. On the other hand Cr(VI) scarcely exists alone in wastewaters, it is usually found in mixtures with divalent metals. Therefore, the simultaneous removal of Cr(VI) and divalent metals in binary mixtures and the interactive mechanism governing Cr(VI) elimination have gained more and more attention. In the present work, kinetics of Cr(VI) sorption onto exhausted coffee from Cr(VI)–Cu(II) binary mixtures has been studied in a stirred batch reactor. A model including Cr(VI) sorption and reduction, Cr(III) sorption and the effect of the presence of Cu(II) in these processes has been developed and validated. This study constitutes an important advance in modeling Cr(VI) sorption kinetics especially when chromium sorption is in part based on the sorbent capacity of reducing hexavalent chromium and a metal cation is present in the binary mixture. - Highlights: • A kinetic model including Cr(VI) reduction, Cr(VI) and Cr(III) sorption/desorption • Synergistic effect of Cu(II) on Cr(VI) elimination included in the model • Model validation by checking it against independent sets of data.

  7. Selective adsorption of Cr(VI) ions from aqueous solutions using Cr(6+)-imprinted Pebax/chitosan/GO/APTES nanofibrous adsorbent.

    Science.gov (United States)

    Etemadi, Mohammadmahdi; Samadi, Saman; Yazd, Shabnam Sharif; Jafari, Pooya; Yousefi, Negin; Aliabadi, Majid

    2017-02-01

    In the present study, a novel Cr(6+)-imprinted Pebax/chitosan/GO/APTES nanofibrous adsorbent (Cr(6+)-PCGA) was prepared and its performance was compared with PCGA nanofibers for selective sorption of Cr(VI) ions from aqueous solutions. The prepared nanofibers were characterized using FTIR, SEM and EDAX analysis. The influence of batch sorption experiments including GO/APTES content, pH, contact time, Cr(VI) initial concentration and temperature on the Cr(VI) sorption efficiency using synthesized nanofibers was investigated. The Cr(VI) sorption data were well described using pseudo-second-order kinetic and Redlich-Peterson isotherm models. The maximum sorption capacities of Cr(6+)-PCGA and PCGA nanofibers for Cr(VI) ions sorption were found to be 204.5 and 550.5mgg(-1), respectively. Thermodynamic studies indicated an endothermic and spontaneous nature of Cr(VI) ions sorption using both Cr(6+)-PCGA and PCGA nanofibers. The selectivity coefficient values of Cr(VI)/Pb(II), Cr(VI)/Cu(II) and Cr(VI)/Ni(II) indicated the higher selectivity of Cr(6+)-PCGA nanofibrous adsorbent for Cr(VI) ions separation compared to PCGA nanofibers. The good stability and reusability of Cr(6+)-PCGA nanofibrous adsorbent for five sorption/desorption cycles promised a higher potential of ion-imprinted nanofibers for separation of metal ions from aqueous systems in a large scale. Copyright © 2016 Elsevier B.V. All rights reserved.

  8. Surface complexation modeling of U(VI) sorption on GMZ bentonite in the presence of fulvic acid

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Jie [Lanzhou Univ. (China). Radiochemistry Laboratory; Ministry of Industry and Information Technology, Guangzhou (China). The 5th Electronics Research Inst.; Luo, Daojun [Ministry of Industry and Information Technology, Guangzhou (China). The 5th Electronics Research Inst.; Qiao, Yahua; Wang, Liang; Zhang, Chunming [Ministry of Environmental Protection, Beijing (China). Nuclear and Radiation Safety Center; Wu, Wangsuo [Lanzhou Univ. (China). Radiochemistry Laboratory; Ye, Yuanlv [Ministry of Environmental Protection, Beijing (China). Nuclear and Radiation Safety Center; Lanzhou Univ. (China). Radiochemistry Laboratory

    2017-03-01

    In this work, experiments and modeling for the interactions between uranyl ion and GMZ bentonite in the presence of fulvic acid are presented. The results demonstrated that FA is strongly bound to GMZ bentonite, and these molecules have a very large effect on the U(VI) sorption. The results also demonstrated that U(VI) sorption to GMZ bentonite in the presence and absence of sorbed FA can be well predicted by combining SHM and DLM. According to the model calculations, the nature of the interactions between FA with U(VI) at GMZ bentonite surface is mainly surface complex. The first attempt to simulate clay interaction with humus by the SHM model.

  9. Surface complexation modeling of U(VI) sorption on TiO{sub 2} in the presence of fulvic acid

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Yuanlv [Ministry of Environmental Protection, Beijing (China). Nuclear and Radiation Safety Center; Univ. Lanzhou (China). Radiochemistry Lab.; Qiao, Yahua; Wang, Liang; Liu, Fudong; Zhang, Chunming [Ministry of Environmental Protection, Beijing (China). Nuclear and Radiation Safety Center; Guo, Zhijun; Wu, Wangsuo [Univ. Lanzhou (China). Radiochemistry Lab.

    2016-05-01

    In this work, experiments and modeling for the interactions between uranyl ion and TiO{sub 2} in the presence of fulvic acid are presented. The results demonstrated that FA is strongly bound to TiO{sub 2}, and these molecules have a very large effect on the U(VI) sorption, and vice versa. The results also demonstrated that U(VI) sorption to TiO{sub 2} in the presence and absence of sorbed FA can be well predicted with the SCD model (surface and complex distribution). According to the model calculations, the nature of the interactions between FA with U(VI) at TiO{sub 2} surface is mainly surface complex and electrostatic potential.

  10. The ternary sorption system U(VI)-phosphate-silica explained by spectroscopy and thermodynamic modelling

    Energy Technology Data Exchange (ETDEWEB)

    Foerstendorf, Harald; Stockmann, Madlen; Heim, Karsten; Mueller, Katharina; Brendler, Vinzenz [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Surface Processes; Comarmond, M.J.; Payne, T.E. [Australian Nuclear Science and Technology Organisation, Lucas Heights (Australia); Steudtner, Robin [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Inst. of Resource Ecology

    2017-06-01

    Spectroscopic data of sorption processes potentially provide direct impact on Surface Complexation Modelling (SCM) approaches. Based on spectroscopic data of the ternary sorption system U(VI)/phosphate/silica strongly suggesting the formation of a precipitate as the predominant surface process, SCM calculations accurately reproduced results from classical batch experiments.

  11. Tungstate (VI) sorption on hematite: An in situ ATR-FTIR probe on the mechanism.

    Science.gov (United States)

    Rakshit, Sudipta; Sallman, Bryan; Davantés, Athénais; Lefèvre, Grégory

    2017-02-01

    Owing to the suspected toxicity and carcinogenicity of tungstate (VI) oxyanions [i.e. mono tungstate and several polytungstate, generally represented by W (VI)], the environmental fate of W (VI) has been widely studied. Sorption is regarded as a major mechanism by which W (VI) species are retained in the solid/water interface. Iron (hydr)oxides have been considered important environmental sinks for W (VI) species. Here we report sorption mechanisms of W (VI) on a common iron oxide mineral-hematite under environmentally relevant solution properties using in situ attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopic probes. Initial W (VI) loadings varied from 10 to 200 μM at fixed pH values ranged from 4.6 to 8.1. For pH envelop (pHs = 4.6, 5.0, 5.5, 6.0, 6.5, 7.5, and 8.1) experiments, fixed W (VI) concentrations (i.e. 10 & 200 μM) were used to understand the effects of pH. The results indicated that at acidic pH values (pH hematite surface and the strength of the interaction increases with decreasing pH. In addition, initial W (VI) concentration affected the sorption mechanisms of W (VI) on hematite. Our study will aid the molecular level understanding of W (VI) retention on iron oxide surfaces. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Sorption of U(VI) on goethite: Effects of pH, ionic strength, phosphate, carbonate and fulvic acid

    Energy Technology Data Exchange (ETDEWEB)

    Guo Zhijun [Radiochemistry Lab, School of Nuclear Science and Technology, Lanzhou University, Lanzhou 730000 (China)], E-mail: guozhj@lzu.edu.cn; Li Yan; Wu Wangsuo [Radiochemistry Lab, School of Nuclear Science and Technology, Lanzhou University, Lanzhou 730000 (China)

    2009-06-15

    U(VI) sorption on goethite was investigated as functions of pH, solid-to-liquid ratio (m/V), ionic strength and U(VI) concentration by a batch experimental method. Effects of phosphate, carbonate and fulvic acid (FA) on U(VI) sorption were examined. It was found that the sorption of U(VI) increases from 0% to 100% over the pH range of 2.5-4.5 and keeps constant in the high pH range. The sorption of U(VI) on goethite is insensitive to ionic strength. Different surface complexes in the framework of double-layer model were examined for fitting the sorption of U(VI) on goethite. A model with two mononuclear inner-sphere surface complexes, {identical_to}SOUO{sub 2}{sup +} and {identical_to}SOUO{sub 2}OH, was found capable of reproducing the pH sorption edges, the sorption isotherms and the sorption data with variable m/V in this study. The proposed model can also interpret the pH sorption edge collected at P{sub CO{sub 2}}=10{sup -3.58}atm without considering any ternary surface complexes of carbonate. Moreover, it was found that the presence of phosphate at relatively high concentration (6x10{sup -4} mol/L) promotes U(VI) sorption. The presence of FA of 20 mg/L has little effect on the sorption of U(VI) on goethite.

  13. Sorption and desorption studies of chromium(VI) from nonviable cyanobacterium Nostoc muscorum biomass

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, V.K. [Department of Chemistry, Indian Institute of Technology Roorkee, Roorkee 247667 (India)], E-mail: vinodfcy@iitr.ernet.in; Rastogi, A. [Department of Chemistry, Indian Institute of Technology Roorkee, Roorkee 247667 (India)

    2008-06-15

    This communication presents results pertaining to the sorptive and desorptive studies carried out on chromium(VI) removal onto nonviable freshwater cyanobacterium (Nostoc muscorum) biomass. Influence of varying the conditions for removal of chromium(VI), such as the pH of aqueous solution, the dosage of biosorbent, the contact time with the biosorbent, the temperature for the removal of chromium, the effect of light metal ions and the adsorption-desorption studies were investigated. Sorption interaction of chromium on to cyanobacterial species obeyed both the first and the second-order rate equation and the experimental data showed good fit with both the Langmuir and freundlich adsorption isotherm models. The maximum adsorption capacity was 22.92 mg/g at 25 {sup o}C and pH 3.0. The adsorption process was endothermic and the values of thermodynamic parameters of the process were calculated. Various properties of the cyanobacterium, as adsorbent, explored in the characterization part were chemical composition of the adsorbent, surface area calculation by BET method and surface functionality by FTIR. Sorption-desorption of chromium into inorganic solutions and distilled water were observed and this indicated the biosorbent could be regenerated using 0.1 M HNO{sub 3} and EDTA with upto 80% recovery. The biosorbents were reused in five biosorption-desorption cycles without a significant loss in biosorption capacity. Thus, this study demonstrated that the cyanobacterial biomass N. muscorum could be used as an efficient biosorbent for the treatment of chromium(VI) bearing wastewater.

  14. Sorption of chromium (VI) by Mg/Fe hydrotalcite type compunds

    Energy Technology Data Exchange (ETDEWEB)

    García-Sosa, I., E-mail: irma.garcia@inin.gob.mx; Cabral-Prieto, A., E-mail: agustin.cabral@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Departamento de Química (Mexico); Nava, N., E-mail: tnava@imp.mx; Navarrete, J. [Instituto Mexicano del Petróleo (Mexico); Olguín, M. T., E-mail: teresa.olguin@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Departamento de Química (Mexico); Escobar, Luis, E-mail: luis.escobar@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Departamento de Física (Mexico); López-Castañares, R., E-mail: rlc@anuies.mx; Olea-Cardoso, O., E-mail: olc@anuies.mx [Universidad Autónoma del Edo. de México, Facultad de Química (Mexico)

    2015-06-15

    The synthesis by co-precipitation and characterization by X-ray diffraction, Raman and Mössbauer spectroscopies of Mg-Fe-hydrotalcite compounds, and their sorption capacities for Cr(VI) in aqueous media were carried out. The average sorption capacity of Cr(VI) for the non-thermal treated samples was of 6.2 mg/g. The ferrihydrite was omnipresent in all prepared hydrotalcite samples. A brief discussion is made on the role of both the hydrotalcite and ferrihydrite for removing such amount of Cr(VI)

  15. Surface Engineering of PAMAM-SDB Chelating Resin with Diglycolamic Acid (DGA) Functional Group for Efficient Sorption of U(VI) and Th(IV) from Aqueous Medium

    Energy Technology Data Exchange (ETDEWEB)

    Ilaiyaraja, P.; Venkatraman, B., E-mail: chemila07@gmail.com [Radiological Safety Division, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Deb, A.K. Singha [Chemical Engineering Division, Bhabha Atomic Research Centre, Mumbai (India); Ponraju, D. [Safety Engineering Division, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Ali, Sk. Musharaf [Chemical Engineering Division, Bhabha Atomic Research Centre, Mumbai (India)

    2017-04-15

    Highlights: • A new DGA-PAMAM-SDB chelating resin has been synthesized for actinide sorption. • Maximum sorption capacities of resin are 682 and 544.2 mg g{sup −1}for U(VI) and Th(IV). • DGA-PAMAM-SDB chelating resin could be regenerated and reused. • DFT calculation of actinides interaction with resin corroborates the experimental. • Resin is effective for sorption of actinides from both aqueous and HNO{sub 3} medium. - Abstract: A novel chelating resin obtained via growth of PAMAM dendron on surface of styrene divinyl benzene resin beads, followed by diglycolamic acid functionalization of the dendrimer terminal. Batch experiments were conducted to study the effects of pH, nitric acid concentration, amount of adsorbent, shaking time, initial metal ion concentration and temperature on U(VI) and Th(IV) adsorption efficiency. Diglycolamic acid terminated PAMAM dendrimer functionalized styrene divinylbenzene chelating resin (DGA-PAMAM-SDB) is found to be an efficient candidate for the removal of U(VI) and Th(IV) ions from aqueous (pH > 4) and nitric acid media (> 3 M). The sorption equilibrium could be reached within 60 min, and the experimental data fits with pseudo-second-order model. Langmuir sorption isotherm model correlates well with sorption equilibrium data. The maximum U(VI) and Th(IV) sorption capacity onto DGA-PAMAMG{sub 5}-SDB was estimated to be about 682 and 544.2 mg g{sup −1} respectively at 25 °C. The interaction of actinides and chelating resin is reversible and hence, the resin can be regenerated and reused. DFT calculation on the interaction of U(VI) and Th(IV) ions with chelating resin validates the experimental findings.

  16. The influence of citric acid, EDTA, and fulvic acid on U(VI) sorption onto kaolinite

    Energy Technology Data Exchange (ETDEWEB)

    Barger, Michelle, E-mail: Michelle.l.barger@wmich.edu [Department of Geosciences, Western Michigan University, Kalamazoo, MI (United States); Koretsky, Carla M. [Department of Geosciences, Western Michigan University, Kalamazoo, MI (United States)

    2011-06-15

    Uranium(VI) sorption onto kaolinite was investigated as a function of pH (3-12), sorbate/sorbent ratio (1 x 10{sup -6}-1 x 10{sup -4} M U(VI) with 2 g/L kaolinite), ionic strength (0.001-0.1 M NaNO{sub 3}), and pCO{sub 2} (0-5%) in the presence or absence of 1 x 10{sup -2}-1 x 10{sup -4} M citric acid, 1 x 10{sup -2}-1 x 10{sup -4} M EDTA, and 10 or 20 mg/L fulvic acid. Control experiments without-solids, containing 1 x 10{sup -6}-1 x 10{sup -4} M U(VI) in 0.01 M NaNO{sub 3} were used to evaluate sorption to the container wall and precipitation of U phases as a function of pH. Control experiments demonstrate significant loss (up to 100%) of U from solution. Although some loss, particularly in 1 x 10{sup -5} and 1 x 10{sup -4} M U experiments, is expected due to precipitation of schoepite, adsorption on the container walls is significant, particularly in 1 x 10{sup -6} M U experiments. In the absence of ligands, U(VI) sorption on kaolinite increases from pH {approx}3 to 7 and decreases from pH {approx}7.5 to 12. Increasing ionic strength from 0.001 to 0.1 M produces only a slight decrease in U(VI) sorption at pH < 7, whereas 10% pCO{sub 2} greatly diminishes U(VI) sorption between pH {approx}5.5 and 11. Addition of fulvic acid produces a small increase in U(VI) sorption at pH < 5; in contrast, between pH 5 and 10 fulvic acid, citric acid, and EDTA all decrease U(VI) sorption. This suggests that fulvic acid enhances U(VI) sorption slightly via formation of ternary ligand bridges at low pH, whereas EDTA and citric acid do not form ternary surface complexes with the U(VI), and that all three ligands, as well as carbonate, form aqueous uranyl complexes that keep U(VI) in solution at higher pH.

  17. Sorption of V and VI group metalloids (As, Sb, Te on modified peat sorbents

    Directory of Open Access Journals (Sweden)

    Ansone-Bertina Linda

    2016-01-01

    Full Text Available The present work investigates arsenic, antimony and tellurium sorption using iron modified peat. The results were obtained using batch tests and the sorption was studied as a function of initial metalloid concentration, pH and sorption time, as well as the presence of competing substances. The obtained results indicate that modification of peat with Fe compounds significantly enhances the sorption capacity of the sorbents used for sorption of arsenic, antimony and tellurium. The optimal pH interval for the sorption of Sb(III is 6.5–9 and for As(V and Sb(V – 3–6, while As(III and tellurium sorption using Fe-modified peat is favourable in a wider interval of 3–9. The presence of competing ions as well as HA affect sorption of metalloids on Fe-modified peat. A minor impact on the reduction of metalloid sorption was detected in the presence of nitrate, sulphate, carbonate and tartrate ions, while in the presence of phosphate and HA the sorption ability of metalloids can be considerably reduced. The obtained results of kinetic experiments indicate that sorption of metalloids on Fe-modified peat mainly occurs relying on mechanisms of physical sorption processes.

  18. Investigation of metal ions sorption of brown peat moss powder

    Science.gov (United States)

    Kelus, Nadezhda; Blokhina, Elena; Novikov, Dmitry; Novikova, Yaroslavna; Chuchalin, Vladimir

    2017-11-01

    For regularities research of sorptive extraction of heavy metal ions by cellulose and its derivates from aquatic solution of electrolytes it is necessary to find possible mechanism of sorption process and to choice a model describing this process. The present article investigates the regularities of aliovalent metals sorption on brown peat moss powder. The results show that sorption isotherm of Al3+ ions is described by Freundlich isotherm and sorption isotherms of Na+ i Ni2+ are described by Langmuir isotherm. To identify the mechanisms of brown peat moss powder sorption the IR-spectra of the initial brown peat moss powder samples and brown peat moss powder samples after Ni (II) sorption were studied. Metal ion binding mechanisms by brown peat moss powder points to ion exchange, physical adsorption, and complex formation with hydroxyl and carboxyl groups.

  19. Uranium(VI) sorption complexes on silica in the presence of calcium and carbonate.

    Science.gov (United States)

    Saleh, Alaaeldine Sh; Lee, Jun-Yeop; Jo, Yongheum; Yun, Jong-Il

    2018-02-01

    Uranium sorption on minerals and related solids depends to a large degree on its aqueous speciation. The present work attempts to understand the U(VI) sorption behavior on silica under environmentally relevant conditions, i.e. at neutral to weakly alkaline pH and in the presence of dissolved calcium and carbonate. Under these conditions, Ca(UO2)(CO3)32- and Ca2(UO2)(CO3)3(aq) complexes emerge as the dominant aqueous U(VI) species. The U(VI) sorption affinity was measured as a function of contact time, solution pH, and humic acid. The U(VI) sorption decreased with increase of pH and was not affected by the addition of 50 mg/L humic acid. On the other hand, nitric acid was more effective than EDTA and carbonate at desorbing U(VI). Generally, the U(VI) sorbed on silica at neutral pH was less readily desorbed than that sorbed at higher pH values. Therefore, the U(VI) complex favorably sorbed on silica at the neutral pH is more strongly bound to the silica surface than that sorbed at higher pH values. Time-resolved laser fluorescence spectroscopy confirmed the results of the batch sorption experiments and revealed the presence of two surface U(VI) complexes with fluorescence lifetimes 251 ± 8 μs and 807 ± 24 μs. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. The role of nanopores on U(VI) sorption and redox behavior in U(VI)-contaminated subsurface sediments

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Huifang; Roden, Eric E.; Kemner, Kenneth M.; Jung, Hun-Bok; Konishi, Hiromi; Boyanov, Maxim; Sun, Yubing; Mishra, Bhoopesh

    2013-10-16

    Most reactive surfaces in clay-dominated sediments are present within nanopores (pores of nm dimension). The behavior of geological fluids and minerals in nanopores is significantly different from those in normal non-nanoporous environments. The effect of nanopore surfaces on U(VI) sorption/desorption and reduction is likely to be significant in clay-rich subsurface environments. Our research results from both model nanopore system and natural sediments from both model system (synthetic nanopore alumina) and sediments from the ORNL Field Research Center prove that U(VI) sorption on nanopore surfaces can be greatly enhanced by nanopore confinement environments. The results from the project provide advanced mechanistic, quantitative information on the physiochemical controls on uranium sorption and redox behavior in subsurface sediments. The influence of nanopore surfaces on coupled uranium sorption/desorption and reduction processes is significant in virtually all subsurface environments, because most reactive surfaces are in fact nanopore surfaces. The results will enhance transfer of our laboratory-based research to a major field research initiative where reductive uranium immobilization is being investigated. Our results will also provide the basic science for developing in-situ colloidal barrier of nanoporous alumina in support of environmental remediation and long term stewardship of DOE sites.

  1. Sorption of Heavy Metal Ions from Mine Wastewater by Activated ...

    African Journals Online (AJOL)

    Michael

    2016-12-02

    Dec 2, 2016 ... Buah, W. K. and Dankwah, J. R. (2016), “Sorption of Heavy Metals from Mine Wastewater by Activated. Carbons Prepared ... A study on sorption of heavy metal ions: Lead (Pb2+), Copper (Cu2+) and Cadmium (Cd2+) from mine wastewater by activated ... (Pb), having relatively high densities and are toxic.

  2. MEMS tandem ion-sorption micropump

    Science.gov (United States)

    Grzebyk, T.

    2017-12-01

    This paper presents a two-stage MEMS ion-sorption micropump, which works in a wide range of pressures—it allows efficient evacuation of gases from the internal volume of any microsystem starting from atmospheric pressure down to 10‑6 hPa. The miniature pre-vacuum pump is realized as a two-electrode silicon–glass structure with a very close inter-electrode distance. The use of the silicon substrate as a getter material instead of a metallic layer significantly increases the pumping capacity and as a result, the initial pressure can be reduced to a level of 1 hPa. From this point the pumping is continued with the second glow-discharge high vacuum micropump. This pump is a multilayer structure, in which ions are trapped in crossed electric and magnetic fields. It allows further reduction of pressure down to 10‑6 hPa. Both pumps are technologically compatible and together they enable the on-chip generation of avacuum at the desired level in a variety of miniaturized devices.

  3. Chromium(VI) removal via reduction-sorption on bi-functional silica adsorbents.

    Science.gov (United States)

    Zaitseva, Nataliya; Zaitsev, Vladimir; Walcarius, Alain

    2013-04-15

    Organically-modified silica gels bearing mercaptopropyl and ethylenediaminetriacetate groups (SiO2-SH/ED3A) have been used for reduction and subsequent sequestration of Cr(VI) species. The uptake mechanism involves Cr(VI) reduction by thiol groups (SH) and further immobilization of the so-generated Cr(III) species via complexation to the ethylenediaminetriacetate moieties (ED3A). The most appropriate pH range (1-3) for complete Cr(VI) reduction-sorption by SiO2-SH/ED3A originates from the balance between full reduction of Cr(VI) by SH, requiring low pH values, and quantitative complexation of Cr(III) by ED3A, which is favored in less acidic media. Such bi-functional adsorbents are considerably more effective at removal of Cr(VI) than those simply modified with thiol groups alone. The whole reduction-sorption process was characterized by fast kinetics, thus permitting efficient use of the SiO2-SH/ED3A adsorbent in dynamic conditions (column experiments). Monitoring the amount of immobilized chromium species on the solid was achieved using X-ray fluorescence spectroscopy and UV-vis spectroscopy. Studying the influence of ionic strength and presence of heavy metals revealed few interference on Cr(VI) removal. Copyright © 2013 Elsevier B.V. All rights reserved.

  4. SORPTION OF Cu2+ IONS ONTO DIATOMITE CONSTITUENTS

    Directory of Open Access Journals (Sweden)

    Vasile Rusu

    2009-06-01

    Full Text Available Studies of the sorption capacity towards Cu2+ ions of diatomite from the Ghidirim location of RM, as well as of the extracted clay phase are presented. Separated clay fraction from diatomic material is clean enough, and especially is rich in montmorillonite. Maximum sorption capacity for studied clay fraction is achieved by rising the temperature of calcination treatment up to 200oC. At higher temperatures the lattice of montmorillonite is contracted and its sorption capacity towards Cu2+ ions decreases strongly.

  5. Functionalization of Magnetic Chitosan Particles for the Sorption of U(VI, Cu(II and Zn(II—Hydrazide Derivative of Glycine-Grafted Chitosan

    Directory of Open Access Journals (Sweden)

    Mohammed F. Hamza

    2017-05-01

    Full Text Available A new magnetic functionalized derivative of chitosan is synthesized and characterized for the sorption of metal ions (environmental applications and metal valorization. The chemical modification of the glycine derivative of chitosan consists of: activation of the magnetic support with epichlorohydrin, followed by reaction with either glycine to produce the reference material (i.e., Gly sorbent or glycine ester hydrochloride, followed by hydrazinolysis to synthesize the hydrazide functionalized sorbent (i.e., HGly sorbent. The materials are characterized by titration, elemental analysis, FTIR analysis (Fourrier-transform infrared spectrometry, TGA analysis (thermogravimetric analysis and with SEM-EDX (scanning electron microscopy coupled to energy dispersive X-ray analysis. The sorption performances for U(VI, Cu(II, and Zn(II are tested in batch systems. The sorption performances are compared for Gly and HGly taking into account the effect of pH, the uptake kinetics (fitted by the pseudo-second order rate equation, and the sorption isotherms (described by the Langmuir and the Sips equations. The sorption capacities of the modified sorbent reach up to 1.14 mmol U g−1, 1.69 mmol Cu g−1, and 0.85 mmol Zn g−1. In multi-metal solutions of equimolar concentration, the chemical modification changes the preferences for given metal ions. Metal ions are desorbed using 0.2 M HCl solutions and the sorbents are re-used for five cycles of sorption/desorption without significant loss in performances.

  6. Functionalization of Magnetic Chitosan Particles for the Sorption of U(VI), Cu(II) and Zn(II)-Hydrazide Derivative of Glycine-Grafted Chitosan.

    Science.gov (United States)

    Hamza, Mohammed F; Aly, Mohsen M; Abdel-Rahman, Adel A-H; Ramadan, Samar; Raslan, Heba; Wang, Shengye; Vincent, Thierry; Guibal, Eric

    2017-05-16

    A new magnetic functionalized derivative of chitosan is synthesized and characterized for the sorption of metal ions (environmental applications and metal valorization). The chemical modification of the glycine derivative of chitosan consists of: activation of the magnetic support with epichlorohydrin, followed by reaction with either glycine to produce the reference material (i.e., Gly sorbent) or glycine ester hydrochloride, followed by hydrazinolysis to synthesize the hydrazide functionalized sorbent (i.e., HGly sorbent). The materials are characterized by titration, elemental analysis, FTIR analysis (Fourrier-transform infrared spectrometry), TGA analysis (thermogravimetric analysis) and with SEM-EDX (scanning electron microscopy coupled to energy dispersive X-ray analysis). The sorption performances for U(VI), Cu(II), and Zn(II) are tested in batch systems. The sorption performances are compared for Gly and HGly taking into account the effect of pH, the uptake kinetics (fitted by the pseudo-second order rate equation), and the sorption isotherms (described by the Langmuir and the Sips equations). The sorption capacities of the modified sorbent reach up to 1.14 mmol U g-1, 1.69 mmol Cu g-1, and 0.85 mmol Zn g-1. In multi-metal solutions of equimolar concentration, the chemical modification changes the preferences for given metal ions. Metal ions are desorbed using 0.2 M HCl solutions and the sorbents are re-used for five cycles of sorption/desorption without significant loss in performances.

  7. As(V)/Cr(VI) pollution control in soils, hemp waste, and other by-products: competitive sorption trials.

    Science.gov (United States)

    Quintáns-Fondo, Ana; Ferreira-Coelho, Gustavo; Paradelo-Núñez, Remigio; Nóvoa-Muñoz, Juan Carlos; Arias-Estévez, Manuel; Fernández-Sanjurjo, María José; Álvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino

    2016-10-01

    We study As(V)/Cr(VI) competitive sorption on a forest soil, a vineyard soil, pyritic material, mussel shell, pine bark, oak ash, and hemp waste, adding variable As(V) and Cr(VI) concentrations or displacing each pollutant with the same concentration of the other. When using variable concentrations, As(V) showed more affinity than Cr(VI) for sorption sites on most materials (sorption up to >84 % on oak ash and pyritic material). The only exception was pine bark, with clearly higher Cr(VI) sorption (>90 %) for any Cr(VI)/As(V) concentration added. Regarding the displacement experiments, when As(V) was added and reached sorption equilibrium, the subsequent addition of equal Cr(VI) concentration did not cause relevant As displacement from oak ash and pyritic material, indicating strong As bindings, and/or low competitive effects. When Cr(VI) was added and reached sorption equilibrium, the subsequent addition of equal As(V) concentration caused Cr(VI) displacement from all materials except pine bark, indicating weak Cr bindings. In view of these results, oak ash and the pyritic material could be used to remove As(V) in concentrations as high as 6 mmol L(-1), even in the presence of a wide range of Cr(VI) concentrations, whereas pine bark could be used to remove Cr(VI) concentrations as high as 6 mmol L(-1). The other materials assayed (including hemp waste, studied for the first time as As(V) and Cr(VI) bio-sorbent) cannot be considered appropriate to remove As(V) and/or Cr(VI) from polluted media.

  8. New Composite Sorbents for Caesium and Strontium Ions Sorption

    Directory of Open Access Journals (Sweden)

    Mykola Kartel

    2017-06-01

    Full Text Available Composite lignocellulose-inorganic sorbents derived from plant residues of agriculture and food industry, modified with ferrocyanides of d-metals and hydrated antimony pentoxide were prepared. Caesium and strontium ions removal from water was tested by radiotracer method. Sorption of heavy metal ions, methylene blue, gelatin, vitamin B12 was also studied.

  9. Kinetics and thermodynamics of uranium(VI) sorption on hydrous silica

    Energy Technology Data Exchange (ETDEWEB)

    Pathak, P.N.; Choppin, G.R. [Florida State Univ., Tallahassee, FL (United States). Dept. of Chemistry and Biochemistry

    2007-07-01

    Sorption of uranyl ion, UO{sub 2}{sup 2+}, on SiO{sub 2}.{chi}H{sub 2}O (silica gel) has been investigated as a function of time, amount of silica gel (0.10-0.60g), uranium concentration (5.00 x 10{sup -5}-1.00 x 10{sup -3}M), ionic strength (0.20-1.40M NaClO{sub 4}), pH ({proportional_to} 2.0-6.0), and temperature (283-333K). Based on kinetic data, the diffusion coefficient of UO{sub 2}{sup 2+} ion was calculated to be 6.83({+-}0.22) x 10{sup -12}m{sup 2}s{sup -1} under particle diffusion-controlled conditions. The rate of sorption of uranyl ion on silica gel was determined to be 8.56({+-}0.50) x 10{sup -2}min{sup -1} at 298K, pH 1.82{+-}0.05 and 0.20M NaClO{sub 4}. The uranyl sorption data on silica gel followed the Freundlich, Langmuir and Dubinin-Radushkevich (D-R) isotherms. Uranyl sorption (%) in creased with ionic strenght from 11.48{+-}0.03 (0.20M NaClO{sub 4}) to 34.81{+-}0.20 (1.40M NaClO{sub 4}) at pH 2.79{+-}0.03 using 0.10g silica gel. The sorption decreased in the presence of 1.00 x 10{sup -3} M fluoride and oxalate ions; while the presence of carbonate anion showed negligible change in uranyl sorption profile in the pH range of 2 to 6 at 0.20M NaClO{sub 4}. Temperature variation experiments showed that the sorption of uranium on silica gel had an endothermic enthalpy, which became more spontaneous at elevated temperatures. (orig.)

  10. Changes in the Kinetics of Uranium(VI) Sorption Reactions to Mineral Surfaces in the Presence of Fulvic Acid

    Science.gov (United States)

    Honeyman, B. D.; Tinnacher, R. M.

    2010-12-01

    In this study, we investigate changes in the kinetics of uranium(VI) sorption reactions to silica sand due to the presence of fulvic acid, a recalcitrant natural organic matter fraction. On the field scale, local contact times between metal contaminants and bulk mineral phases may often be too short to attain full sorption equilibria. Hence, kinetic limitations for surface reactions need to be included in predictive transport models. Natural organic matter is ubiquitous in the environment and can substantially influence metal sorption and transport behavior in saturated porous media. However, at this point little is known about potential effects of organic matter on metal sorption kinetics. Therefore, we investigated the kinetics of uranium(VI) (U(VI)) sorption onto a pretreated silica sand in the absence and presence of fulvic acid in lab-scale experiments. Furthermore, experimental data were simulated in pseudo-first order kinetic models in order to determine the characteristic times for U(VI) sorption reactions under various chemical conditions. Last, speciation modeling allowed for a qualitative assessment of dominant U(VI) solution species as a function of organic ligand concentrations and pH. Results indicate that U(VI) surface reactions are slowed down in the presence of low concentrations of fulvic acid (0.4 and 4.3 mg/l TOC), at conditions where U(VI)-fulvic acid solution complexes can be neglected. This kinetic behavior can be attributed to the competition of U(VI) and fulvic acid for a limited number of fast-sorbing surface sites. In contrast, metal sorption reactions seem to be faster relative to the binary metal-mineral system at a high FA concentration (26 mg/l TOC) and pH conditions where a substantial fraction of U(VI)-FA solution complexes is expected. In this case, U(VI) and fulvic acid sorption kinetics appear to be very similar, which suggests the formation of ternary U(VI)-FA-surface complexes. Hence, kinetic sorption data indicate a change in

  11. Sorption and desorption of silver ions by bentonite clays.

    Science.gov (United States)

    Constantino, Leonel Vinicius; Quirino, Juliana Nunes; Monteiro, Alessandra Maffei; Abrão, Taufik; Parreira, Paulo Sérgio; Urbano, Alexandre; Santos, Maria Josefa

    2017-04-01

    Anthropogenic activities have increased the concentration of metal species in the environment. The toxicity of silver ions to aquatic and terrestrial organisms has required monitoring by analytical methods, besides actions to promote its control as pollutant. Sorption and desorption processes are directly related to the mobility and availability of metal ions in the environment. In this context, clay minerals can be used for pre-concentration, removal and recovery of silver ions from aqueous solution. Herein, two bentonite clays (BaVC-1 and SWy-2) were characterised and applied to investigate the sorption and desorption of silver ions. Isotherms were fitted to the dual-mode Langmuir-Freundlich model to qualify and quantify sorption sites and evaluate the mobilisation process. The maximum sorption capacity was 743 and 849 meq kg -1 for BaVC-1 and SWy-2, respectively. Hysteresis index (HI) and mobilisation factor (MF) suggest that the desorption of silver ions in BaVC-1 is about four times more conducive compared to that in SWy-2, although both materials have demonstrated a great potential for Ag + pre-concentration from aqueous solutions.

  12. Influence of the temperature in the uranium (Vi) sorption in zirconium diphosphate; Influencia de la temperatura en la sorcion de uranio (VI) en difosfato de circonio

    Energy Technology Data Exchange (ETDEWEB)

    Garcia G, N.; Solis, D. [Universidad Autonoma del Estado de Mexico, Facultad de Quimica, Paseo Colon y Paseo Tollocan, 50120 Toluca, Estado de Mexico (Mexico); Ordonez R, E., E-mail: nidgg@yahoo.com.mx [ININ, Departamento de Quimica, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2012-10-15

    In the present work was evaluated the uranium (Vi) sorption at 10, 20, 30, 40 and 60 C on the zirconium diphosphate (ZrP{sub 2}O{sub 7}). They were carried out kinetic and isotherms using the method by lots, these will allow to fix the sorption time (kinetic) and to explain the behavior of this sorption in different ph conditions and temperature (isotherm). The quantity of retained uranium in the surface was quantified by means of the fluorescence technique. (Author)

  13. Study of sorption mechanisms of europium(3) and uranium(6) ions on clays : impact of silicates; Etude des mecanismes de retention des ions U(6) et Eu(3) sur les argiles: influence des silicates

    Energy Technology Data Exchange (ETDEWEB)

    Kowal-Fouchard, A

    2002-11-01

    Bentonite clay has been selected as a potential buffer or backfill material in a number of disposal programmes for high level waste. In order to enhance the thermodynamic database of sorption phenomena at the solid-water interface, we have investigated sorption mechanisms of europium(III) and uranium(VI) ions onto montmorillonite and bentonite. Thermodynamic data were obtained for different ions concentrations, different background electrolytes and different ionic strengths. The structural identification of the surface complexes and sorption sites was carried out using two spectroscopies, XPS and TRLIFS, while sorption edges were performed using batch experiments. However, clays are complex minerals and in order to understand these sorption mechanisms we have studied europium(III) and uranium(VI) retention on a silica and an alumina because these solids are often considered as basic components of clays. The comparison of structural results shows that europium ions are significantly sorbed on permanently charged sites of clay until pH 7. But this ion is also sorbed on {identical_to}SiOH and {identical_to}AlOH sites of montmorillonite at pH higher than 6. Uranyl ions sorption on montmorillonite is mainly explained by retention of three complexes on {identical_to}SiOH sites. Moreover, we have shown that nitrate ions and dissolved silicates affect on uranium(VI) sorption mechanisms onto alumina. Nevertheless, uranyl ions sorption on montmorillonite and bentonite only decreases with increasing carbonate concentration. Finally, all the sorption edges were then modeled using these results and a surface complexation model (2 pK and constant capacitance models). (author)

  14. Effect of humic acid on the uranium(VI) sorption onto phyllite and its mineralogical constituents

    Energy Technology Data Exchange (ETDEWEB)

    Schmeide, K.; Jander, R.; Heise, K.H.; Bernhard, G. [Forschungszentrum Rossendorf e.V. (FZR) (Germany). Inst. fuer Radiochemie

    1999-06-01

    The effect of humic acid (HA) on the uranium(VI) sorption onto phyllite and onto its individual main mineralogical constituents, muscovite, albite, and quartz was studied in air-equilibrated batch experiments in the pH range of 3.5 to 9.5. The uranyl(VI) and HA concentration was 1 x 10{sup -6}M and 5 mg/L, respectively. The ionic strength was held constant at 0.1 M (NaClO{sub 4} solution). A size fraction of 63 to 200 {mu}m of the solids was used, the mass loading was 12.5 g/L, and the experimental volume was 40 mL. (orig.)

  15. Study of the involved sorption mechanisms of Cr(VI) and Cr(III) species onto dried Salvinia auriculata biomass.

    Science.gov (United States)

    Módenes, Aparecido Nivaldo; de Oliveira, Ana Paula; Espinoza-Quiñones, Fernando R; Trigueros, Daniela Estelita Goes; Kroumov, Alexander Dimitrov; Bergamasco, Rosângela

    2017-04-01

    Removal of Cr(VI) species by dried biomass of the aquatic macrophyte Salvinia auriculata was studied in order to understand the involved sorption mechanisms. Kinetic tests were carried out under the conditions such as concentration range of Cr(VI) from 50 to 250 mg L-1 and a temperature of 30 °C. Modification of the biosorbent by the presence of Cr(VI) species was assessed by analysis of its porosity, density and infrared molecular absorption spectrum. A series of experimental approaches involving directed chemical modifications on the biosorbent surface was performed. The main functional groups involved in the sorption mechanisms were identified. The gas sorption analyser was applied and proved that a strong chemical effect of Cr(VI) species on the surface took place, resulting in a leaching organic matter with an obvious and significant increase in the porosity parameters. The intra-particle diffusion model revealed different mass transfer zones into the adsorbent during Cr(VI) removal. New combined Langmuir and Dubinin-Radushkevich isotherm was the best to fit the equilibrium data of Cr(VI) species removal. Finally, Cr(VI) removal was mainly mediated by a redox process where Cr(III) species were formed. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Sorption of environmentally relevant radionuclides (U(VI), Np(V)) and lanthanides (Nd(III)) on feldspar and mica

    Energy Technology Data Exchange (ETDEWEB)

    Richter, Constanze

    2015-11-05

    A safe storage of radioactive waste in repositories is an important task to protect humans and the environment from radio- and chemotoxicity. Long-term safety assessments predict the behavior of potential environmental contaminants like the actinides plutonium, uranium, or neptunium, in the near and far field of repositories. For such safety assessments, it is necessary to know the migration behavior of the contaminants in the environment, which is mainly dependent on the aquatic speciation, the solubility product of relevant solid phases, and the retardation due to sorption on surrounding minerals. Thus, an investigation of sorption processes of contaminants onto different minerals as well as the derivation of mineral specific surface complexation model (SCM) parameters is of great importance. Feldspar and mica are widely distributed in nature. They occur as components of granite, which is considered as a potential host rock for a repository in Germany, and in numerous other rocks, and thus also in the far field of nearly all repositories. However, their sorption behavior with actinides has only been scarcely investigated until now. In order to better characterize these systems and subsequently to integrate these minerals into the long-term safety assessments, this work focuses on the investigation of the sorption behavior of U(VI), Np(V), and Nd(III) as analogue for An(III) onto the minerals orthoclase and muscovite, representing feldspars and mica, respectively. All investigations were performed under conditions relevant to the far field of a repository. In addition to the extensive characterization of the minerals, batch sorption experiments, spectroscopic investigations, and surface complexation modeling were performed to elucidate the uptake and speciation of actinides on the mineral surfaces. In addition, the influence of microorganisms naturally occurring on the mineral surfaces and the effect of Ca{sup 2+} on U(VI) uptake on the minerals was studied. The

  17. Sorption studies on Cr (VI) removal from aqueous solution using cellulose grafted with acrylonitrile monomer.

    Science.gov (United States)

    Hajeeth, T; Sudha, P N; Vijayalakshmi, K; Gomathi, T

    2014-05-01

    Graft copolymerization of acrylonitrile on to cellulosic material derived from sisal fiber can be initiated effectively with ceric ammonium nitrate. The grafting conditions were optimized by changing the concentration of initiator and monomer. The change in crystallinity of the grafted polymeric samples was concluded from the XRD patterns. The prepared cellulose grafted acrylonitrile copolymer was used as an adsorbent to remove Cr (VI) ions from aqueous solutions. The efficiency of the adsorbent was identified from the variation in the percentage of adsorption with contact time, adsorbent dose and pH. From the observed results it was evident that the adsorption of metal ions increases with the increase in contact time and metal ion concentration. An optimum pH was found to be 5.0 for the removal of Cr (VI) from the aqueous solution. The results of the Langmuir, Freundlich, and pseudo first- and second-order studies revealed that the adsorption was found to fit well with Freundlich isotherm and follows pseudo second-order kinetics. From the above results, it was concluded that the cellulose-g-acrylonitrile copolymer was found to be an efficient adsorbent for the removal of Cr (VI) from aqueous waste generated from industries. Copyright © 2014 Elsevier B.V. All rights reserved.

  18. Ion-exchange sorption of silver(I) chloride complexes from aqueous HCl solutions

    Science.gov (United States)

    Kononova, O. N.; Duba, E. V.; Medovikov, D. V.; Efimova, A. S.; Ivanov, A. I.; Krylov, A. S.

    2017-12-01

    The ion-exchange sorption of silver(I) chloride complexes from 1-4 M aqueous solutions of HCl on a series of Purolite anionites with various functional groups was studied. The ion-exchange equilibria in the systems were found to be anomalous according to Raman spectroscopy, which does not significantly affect the sorption properties of the ionites.

  19. SORPTION OF AG(I) IONS ON PAD 400 IMPREGNATED RESIN

    OpenAIRE

    DAMINOVA SHAHLO SHARIPOVNA; KADIROVA ZUKHRA CHINGIZOVNA; SHARIPOV KHASAN TURABOVICH

    2016-01-01

    The polymer matrix (PAD-400) was impregnated by diethyldithiophosphate and used for sorption of silver ions from solutions. The impregnated sorbents were characterized by FTIR, SEM and DTA data. It was established that silver ions have been sorbed from solutions with impregnated sorbents due to formation of the metal-impregnate surface complexes. The sorption process is described better with Freundlich equation.

  20. Sorption of Ammonium Ions onto Natural and Modified Egyptian Kaolinites: Kinetic and Equilibrium Studies

    Directory of Open Access Journals (Sweden)

    Ola I. El-Shafey

    2014-01-01

    Full Text Available Thermally activated, acid-activated, and acid-leached of thermally activated kaolinites were prepared from the Egyptian ore. The physical and chemical properties were studied using N2 sorption at −196°C, FTIR, SEM, and the total surface acidity. The sorption of NH4+ ions on the investigated sorbents was controlled with the solution pH, sorbent dosage, and initial concentration of NH4+ solution. Kinetic and equilibrium NH4+ sorption at 30°C were employed. Four kinetic models were applied to the kinetic sorption data; pseudo-second-order, Elovich, and intraparticle diffusion models fitted well the kinetic data whereas pseudo-first-order model was less applicable. Elovich parameters refer to physical sorption type of NH4+ on nonuniform sites and the intraparticle diffusion controls the sorption of NH4+ by kaolinites to a small extent. The equilibrium sorption data followed Langmuir and D-R models; the negative value of ΔG indicates a spontaneous sorption and the mean sorption energy obtained shows also physical sorption. The sorption capacities of nonactivated and activated Egyptian kaolinites towards NH4+ sorption (10.87–45.45 mg·g−1 were good sorbents as compared with those uptaken by other clays reported in the literature and proved to be more active besides being less expensive and highly available.

  1. Synthesis of ion-exchange resin for selective thorium and uranyl ions sorption

    Science.gov (United States)

    Konovalov, Konstantin; Sachkov, Victor

    2017-11-01

    In this work, the method of ion-exchange resin synthesis selective to radionuclides (uranium and thorium) is presented. The method includes synthesis of polymeric styrene-divinylbenzene macroporous matrix with size of 0.1-0.2 mm, and its subsequent transformation by nitration and then reduction by tin (II) chloride. For passivation of active primary amines partially oxidation by oxygen from air is used. Obtained ion-exchange resin has ratio of sorption sum U+Th to sorption sum of other total rare-earth elements as 1:1.88 at ratio of solid to liquid phase 1:200. The proposed method of ion-exchange resin synthesis is scaled-up for laboratory reactors with volume of 5 and 50 liters.

  2. Sorption of ions Pb2+ by cryogels on the basis of polyvinyl alcohol and bentonite clay

    Directory of Open Access Journals (Sweden)

    А. Seralin

    2012-03-01

    Full Text Available Cryogels on the basis of polyvinyl alcohol and bentonite clay were synthesized. Influences of factors of environment (pH, temperature on properties of composites and them sorption ability were considered. In given article it is resulted sorption kinetics of lead ions on bentonite clay, and also composite cryogel on the basis of polyvinyl alcohol and bentonite clay. It was established that composite cryogels shows much bigger sorption ability.

  3. Removal of the heavy metal ion chromiuim(VI) using Chitosan and Alginate nanocomposites.

    Science.gov (United States)

    Gokila, S; Gomathi, T; Sudha, P N; Anil, Sukumaran

    2017-11-01

    Removal of heavy metals from wastewater is essential to avoid water pollution. In the present study, the performance of Chitosan and Alginate nanocomposites was evaluated for the removal of chromium (VI) from water waste. The physicochemically characterized (FT-IR, XRD, SEM, DSC, and DLS) for wastewater treatment were studied. Batch adsorption experiments were performed to examine the removal process under various factors like the effects of initial concentration, adsorbent dose, pH, and agitation time. The metal ion removal was pH dependent and reached optimum at pH 5.0. Experimental data were analyzed by Langmuir and Freundlich adsorption isotherms. The isotherm study revealed that the adsorption equilibrium is well-fitted to the Freundlich isotherm and the sorption capacity of Chitosan and Alginate nanocomposites is very high, and the adsorbent favors multilayer adsorption. Pseudo-first- and -second-order kinetics models were used for describing kinetic data. It was determined that removal of Cr (VI) be well-fitted by second-order reaction kinetics. From the results, it was concluded that Chitosan and Alginate Nanocomposites is an excellent material as a biosorbent for Cr(VI) from water waste. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. Surface Charge and Ion Sorption Properties of Titanium Dioxide

    Science.gov (United States)

    Ridley, M. K.; Machesky, M. L.; Wesolowski, D. J.; Finnegan, M. P.; Palmer, D. A.

    2001-12-01

    The interaction of submicron metal oxide particles with natural aqueous solutions results in the hydroxylation of surface sites, which impart a pH-dependent surface charge. The charged submicron particles influence processes such as nanoparticle assembly and alteration, crystal growth rates and morphologies, colloid flocculation, and contaminant transport. The surface charge and ion sorption properties of metal-oxide particles may be studied by potentiometric titrations, using hydrogen-electrode concentration-cells or traditional glass electrodes and an autotitrator. These techniques have been used to quantify the adsorption of various ions (Na+, Rb+, Ca2+, Sr2+, Cl-) on rutile, at ionic strengths up to 1.0 molality and temperatures to 250° C. The crystalline rutile used in these studies is less than 400 nm in diameter, has a BET surface area of 17 m2/g, and the 110 and 100 faces predominate. The negative surface charge of the rutile was enhanced by increasing temperature, increasing ionic strength, and decreasing the ionic radii of the electrolyte cation. Moreover, the addition of a divalent cation significantly enhances the negative charge of the rutile surface. These data have been rationalized with the MUSIC model of Hiemestra and van Riemsdijk, and a Basic Stern layer description of the electric double layer (EDL). Model fitting of the experimental data provides binding constants for the adsorbed counterions and divalent cations, and capacitance values as well as corresponding electrical potential values of the binding planes. Recently, new studies have been initiated to determine particle size affects on the proton induced surface charge and ion sorption properties of titanium dioxide. In these studies, anatase with a BET surface area of 40 and 100 m2/g (primary particle sizes of 40 and 10 nm, respectively) is being investigated. The complexity of both the experimental and modeling procedures increases with decreasing particle size. For example, the fine

  5. Cadmium ion sorption onto lignocellulosic biosorbent modified by sulfonation : the origin of sorption capacity improvement

    Science.gov (United States)

    Eun Woo Shin; Roger M. Rowell

    2005-01-01

    Juniper (Juniperus monosperma), a small-diameter underutilized material, has been studied as a lignocellulosic bio-sorbent for removing heavy metals from water. In this study, juniper wood was modified by sulfonation to enhance sorption capacity for cadmium in water. The origin of the enhancement was investigated by observing the sorption behaviors and the change in...

  6. New generation ion-imprinted nanocarrier for removal of Cr(VI) from wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Uygun, Murat, E-mail: muygun@adu.edu.tr [Adnan Menderes University, Kocarl Latin-Small-Letter-Dotless-I Vocational and Training School (Turkey); Feyzioglu, Esra; Oezcal Latin-Small-Letter-Dotless-I skan, Emir; Caka, Mueserref; Ergen, Aygen; Akgoel, Sinan [Ege University, Department of Biochemistry, Faculty of Science (Turkey); Denizli, Adil [Hacettepe University, Department of Chemistry, Faculty of Science (Turkey)

    2013-08-15

    The purpose of this study was to prepare a novel ion-imprinted nanoparticle to remove Cr(VI) ions from waste water. For this, Cr(VI) ions were complexed with 2-methacryloylamido histidine (MAH) and then Cr(VI)-imprinted poly(HEMAH) nanoparticles were synthesized by surfactant-free emulsion polymerization technique. The templates, Cr(VI) ions, were removed from the nanoparticles using 0.1 M of HNO{sub 3} solution. The specific surface area of the Cr(VI)-imprinted poly(HEMAH) nanoparticles was found to be 1,397.85 m{sup 2}/g, and the particle size was calculated as 155.3 nm. These Cr(VI)-imprinted nanoparticles were used for the adsorption/desorption of Cr(VI) ions from its aqueous solutions. The effects of initial Cr(VI) concentration and medium pH on the Cr(VI) adsorption capacity were also studied. The maximum adsorbed amount of Cr(VI) on the imprinted nanoparticles was found to be 3,830.58 mg/g nanoparticle in pH 4.0. In order to investigate the selectivity of the imprinted nanoparticle, adsorption studies were repeated using Cr(III) ions. The selectivity results demonstrated that Cr(VI)-imprinted poly(HEMAH) nanoparticles showed high affinity for the Cr(VI) ions than Cr(III). The Cr(VI)-imprinted nanoparticles were used several times without decreasing their Cr(VI) adsorption capacities.

  7. Influence of (calcium-)uranyl-carbonate complexation on U(VI) sorption on Ca- and Na-bentonites.

    Science.gov (United States)

    Meleshyn, A; Azeroual, M; Reeck, T; Houben, G; Riebe, B; Bunnenberg, C

    2009-07-01

    The influence of uranyl-carbonate and calcium-uranyl-carbonate complexations on the kinetics of U(VI) (approximately 3.4 x 10(-3) mol L(-1)) sorption from NaNO3 and Ca(NO3)2 solutions on Na- and Ca-bentonites at circumneutral ambient conditions was investigated. Complexation of U(VI) in Ca2UO2(CO3)3(aq) aqueous species, dominating the U(VI) speciation in Ca(NO3)2 solution, reduces its adsorption on bentonite by a factor of 2-3 in comparison with that in (UO2)2CO3(OH)3- species, dominating in NaNO3 solution, within the studied period of time (21 days). As a result of the dissolution of accessory calcite, Ca2UO2(CO3)3(aq) can be formed in the initially Ca-free solution in contact with either Na- or Ca-bentonite. U(VI) adsorption on Na-bentonite is a factor of approximately 2 higher than that on Ca-bentonite for solutions with the Ca2UO2(CO3)3(aq) complex dominating aqueous U(VI) speciation. This favors use of Na-bentonite over that of Ca-bentonite in final disposal of radioactive waste. Furthermore, the observed strong correlation between U(VI) adsorption and Mg release as a result of montmorillonite dissolution indicates in agreement with previous findings that under the applied conditions U(VI) is adsorbed on the edge surface of montmorillonite, which is a major mineral phase of the studied clays.

  8. Modification of zirconium diphosphate with salicylic acid and its effect on the uranium (Vi) sorption; Modificacion del difosfato de circonio con acido salicilico y su efecto sobre la sorcion de uranio (VI)

    Energy Technology Data Exchange (ETDEWEB)

    Almazan T, M. G.; Garcia G, N. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Simoni, E., E-mail: guadalupe.almazan@inin.gob.mx [Universidad Paris Sud, Instituto de Fisica Nuclear, Georges Clemenceau No. 15, Orsay (France)

    2014-10-15

    The surface of zirconium diphosphate (ZrP{sub 2}O{sub 7}) was modified with salicylic acid and its effect was evaluated on the uranium (Vi) sorption. The modified surface of the material was analyzed with different analytical techniques among which are included the atomic force microscopy, scanning electron microscopy and X-ray photoelectron spectroscopy. This analysis allowed showing that the salicylic acid is being held on the surface of the zirconium diphosphate. The reactivity of modified zirconium diphosphate compared with uranium (Vi) was investigated using the classical method of batch sorption. The analysis of sorption isotherms shows that the salicylic acid has an important effect in the uranium (Vi) sorption. According to the study conducted, the interaction among the uranium (Vi) and the surface of zirconium diphosphate modified with the salicylic acid most likely leads to the complexes formation of binary (U(Vi)/ZrP{sub 2}O{sub 7}) and ternary (U(Vi)/salicylate/ZrP{sub 2}O{sub 7}) surface. (Author)

  9. Fluoride sorption using organic-inorganic hybrid type ion exchangers.

    Science.gov (United States)

    Sairam Sundaram, C; Meenakshi, S

    2009-05-01

    Research in defluoridation of drinking water has thrown more technologies, with adsorption as more popular alternative among the fluoride endemic habitations across the globe. This paper describes the fluoride removal potential of novel sorbent, synthetic hybrid type ion exchangers from drinking water. Synthesized hybrids were characterized using FTIR studies. Batch adsorption studies were performed as a function of contact time, pH and influence of other interfering anions. The values of defluoridation capacities (DCs) of synthesized polyacrylamide Al(III) phosphate (Al-Ex), polyacrylamide Ce(IV) phosphate (Ce-Ex) and polyacrylamide Zr(IV) phosphate (Zr-Ex) were found to be 2144, 2290 and 2166 mg F(-)/kg, respectively. Ce-Ex has slightly higher DC than Al-Ex and Zr-Ex. The equilibrium data were fitted with isotherm models. Thermodynamic parameters viz., DeltaG(o), DeltaH(o) and DeltaS(o) were calculated to understand the nature of sorption. Field studies were carried out to find the suitability of these sorbents at field condition.

  10. THERMODINAMIC PARAMETERS ON THE SORPTION OF PHOSPHATE IONS BY MONTMORILLONITE

    Directory of Open Access Journals (Sweden)

    Ikhsan Jaslin

    2016-04-01

    Full Text Available The sorption of phosphate by montmorillonite at 10, 30, and 50 oC were investigated aiming to mainly determine thermodynamic parameters for the formation of surface complexes in the adsorption of phosphate ions by montmorillonite. Data were collected by adsorption edge experiments investigating the effect of pH, adsorption isotherms enabling the effect of sorbate concentration, and acid-base titration calculating protons released or taken up by adsorption process. Data analysis was carried out using surface complexation model to fit the data collected in this study using the parameters obtained from previous study, as well as to calculate the values of ΔH and ΔS. Previous study reported that phosphate ions formed two outer-sphere surface complexes with active sites of montmorillonite through hydrogen bonding. In the first complex,  [(XH0– H2L─]─, the phosphate was held to permanent-charge X─ sites on the tetrahedral siloxane faces, and the second complex, [[(SO─(SOH]– – [H2L]─] 2─ was formed through the interaction between the phosphate and variable charge surface hydroxyl groups at the edges of montmorillonite crystals and on the octahedral alumina faces. The values of ΔH for the first and second reactions are 39.756 and 3.765x10-7 kJ mol‒1 respectively. Since both reactions have positive enthalpy values, it can be concluded that the reactions are endothermic. Large energy for the first reaction is needed by X─  sites (permanent negatively charge sites of montmorillonite to be partially desolvated, on which K+ or other surface cations are replaced by H+ ions in the surface protonated process, and are then ready to interact phosphate ions in the solution. Small values of ΔH for the second reactions indicates that hydrogen bonds formed by phosphate and SOH sites in the second reaction are easily broken out, and the phosphate can easily desorbed from the surface. The values of ΔS for the first and second reactions are

  11. Effect of the gamma irradiation on the bio-sorption of Cr (Vi) by orange peel;Efecto de la irradiacion gamma en la biosorcion de Cr(VI) por cascara de naranja

    Energy Technology Data Exchange (ETDEWEB)

    Lugo L, V.; Barrera D, C. E.; Sanchez M, V. [Universidad Autonoma del Estado de Mexico, Centro de Investigacion en Quimica Sustentable, Paseo Tollocan esquina Paseo Colon s/n, 50180 Toluca, Estado de Mexico (Mexico); Urena N, F., E-mail: violelugol@yahoo.e [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2009-07-01

    The orange peel (Citrus sp.) is a bioadsorbent that contains functional groups able to remove Cr (Vi). To study the effect of gamma irradiation in the sorption capacity, the Nn materials were irradiated with gamma rays using a Co{sup 60} source to dose from 10 to 3500 KGy (Nlgamma). The biomass irradiation with gamma rays was successful since it increased the hexavalent chromium removal obtaining a maximum removal percentage of 100%. Sorption isotherms were realized to determine the concentration effect of initial Cr (Vi), the ph effect of the solution and the relationship m/v. (Author)

  12. Kinetics, mechanistic and thermodynamics of Zn(II) ion sorption: a modeling approach

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, Vishal; Balomajumder, Chandrajit; Agarwal, Vijay Kumar [Department of Chemical Engineering, Indian Institute of Technology, Roorkee (India)

    2012-07-15

    Biosorption potential of Cedrus deodara sawdust (CDS) in terms of sorption of Zn(II) ion across liquid phase has been evaluated in the present investigation. The surface of the CDS biomass before the sorption of Zn(II) ions seemed to be more porous, non-crystalline and heterogeneous. The maximum uptake capacity of CDS was 97.39 mg g{sup -1}. Sorption of Zn(II) ion on the surface of CDS sawdust was maximum at pH 5, temperature 45 C, initial concentration of Zn(II) ion 100 mg L{sup -1}, biomass dose 1 g L{sup -1}, contact time 150 min, and agitation rate 160 rpm. Pseudo second-order kinetics with the highest linear regression coefficient (R{sup 2} = 0.99), and lowest values of error functions, i.e., chi ({chi}{sup 2}) and sum of square errors (SSE) against pseudo first-order rate kinetics showed that the sorption of Zn(II) ion on the surface of CDS was mediated by chemosorptive forces of attraction rather than physical adsorption. Mechanistically, relatively higher proportion of sorption of Zn(II) ion in early phase of contact time was profoundly explained by Bangham's equation and film diffusivity (D{sup f}). Intraparticle or pore diffusion (D{sub p}) of Zn(II) ion inside the pores of CDS was rate limiting step at the later stage of contact time. Furthermore, the thermodynamic study on sorption of metal ion delineated the fact that the Zn(II) sorption on the surface of CDS was spontaneous, endothermic together with increased entropy at solid liquid interface. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  13. Effect of pH, ionic strength and humic acid on the sorption of uranium(VI) to attapulgite

    Energy Technology Data Exchange (ETDEWEB)

    Niu Zhiwei [Radiochemistry Laboratory, Lanzhou University, Lanzhou 730000, Gansu (China); Fan Qiaohui [Radiochemistry Laboratory, Lanzhou University, Lanzhou 730000, Gansu (China)], E-mail: fanqiaohui@gmail.com; Wang Wenhua; Xu Junzheng [Radiochemistry Laboratory, Lanzhou University, Lanzhou 730000, Gansu (China); Chen Lei [School of Chemical Engineering, Shandong University of Technology, 255049 Zibo, Shandong (China); Wu Wangsuo [Radiochemistry Laboratory, Lanzhou University, Lanzhou 730000, Gansu (China)], E-mail: wuws@lzu.edu.cn

    2009-09-15

    Attapulgite was investigated to remove UO{sub 2}{sup 2+} from aqueous solutions because of its strong sorption capacity. Herein, the attapulgite sample was characterized by Fourier transform infrared spectra (FTIR), X-ray diffraction (XRD) and acid-base titration in detail. Sorption of UO{sub 2}{sup 2+} on attapulgite was strongly dependent on pH values and ionic strength. The presence of humic acid enhanced the sorption of UO{sub 2}{sup 2+} on attapulgite obviously because of the strong complexation of humic acid (HA) with UO{sub 2}{sup 2+} on attapulgite surface. Sorption of UO{sub 2}{sup 2+} on attapulgite was mainly dominated by ion-exchange or outer-sphere complexation at low pH values, and by inner-sphere complexation at high pH values. The results indicated that attapulgite was a suitable material for the preconcentration and solidification of UO{sub 2}{sup 2+} from large volume of solutions because of its negative surface charge and large surface areas.

  14. Isotherms and thermodynamics for the sorption of heavy metal ions onto functionalized sporopollenin

    Energy Technology Data Exchange (ETDEWEB)

    Gubbuk, Ilkay Hilal, E-mail: ihilalg@gmail.com [Selcuk University, Department of Chemistry, Campus, 42031 Konya (Turkey)

    2011-02-15

    In this study, sporopollenin of Lycopodium clavatum spores was used for the sorption experiment. Glutaraldehyde (GA) immobilized sporopollenin (Sp), is employed as a sorbent in sorption of selected heavy metal ions. The sorbent prepared by sequential treatment of sporopollenin by silanazing compound and glutaraldehyde is suggested for sorption of Cu(II), Zn(II) and Co(II) from aqueous solutions. Experimental conditions for effective sorption of heavy metal ions were optimized with respect to different experimental parameters using batch method in detail. Optimum pH range of Cu(II) has occurred at pH {>=} 5.5 and Zn(II), Co(II) at pH {>=} 5.0, for the batch method. All of the metal ions can be desorbed with 10 cm{sup 3} of 0.5 mol dm{sup -3} of ethylenediaminetetraacetic acid (EDTA) solution. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) isotherm equations were applied to the experimental data. Thermodynamic parameters such as free energy ({Delta}G{sup o}), entropy ({Delta}S{sup o}) and enthalpy ({Delta}H{sup o}) were also calculated from the sorption results used to explain the mechanism of the sorption. The results indicated that this sorbent is successfully employed in the separation of trace Cu(II), Zn(II) and Co(II) from the aqueous solutions.

  15. Ion exchange during heavy metal bio-sorption from aqueous solution by dried biomass of macrophytes.

    Science.gov (United States)

    Verma, V K; Tewari, Saumyata; Rai, J P N

    2008-04-01

    In this study, potentials of oven dried biomass of Eichhornia crassipes, Valisneria spiralis and Pistia stratiotes, were examined in terms of their heavy metal (Cd, Ni, Zn, Cu, Cr and Pb) sorption capacity, from individual-metal and multi-metal aqueous solutions at pH 6.0+/-0.1 (a popular pH of industrial effluent). V. spiralis was the most and E. crassipes was the least efficient for removal of all the metals. Cd, Pb and Zn were efficiently removed by all the three biomass. Cd was removed up to 98% by V. spiralis. Sorption data for Cr, Ni and Cd fitted better to Langmuir isotherm equation, while, the sorption data for Pb, Zn and Cu fitted better to Freundlich isotherm equation. In general, the presence of other metal ions did not influence significantly the targeted metal sorption capacity of the test plant biomasses. Ion exchange was proven the main mechanism involved in bio-sorption and there was a strong ionic balance between adsorbed (H(+) and M(2+)) to the released ions (Na(+) and K(+)) to and from the biomass. No significant difference was observed in the metal exchanged amount, by doubling of metal concentration (15-30 mg/l) in the solution and employing individual-metal and multi-metal solutions.

  16. The Survey of Sorption Ion-Exchange Properties of Paleozoic Natural Minerals in the Static Conditions

    Science.gov (United States)

    Germanova, T. V.; Nefedov, V. A.; Valieva, I. R.

    2017-05-01

    An experimental and exploring process’ results of iron’s ion, manganese and ammonium sodium extraction from aqueous solution by some Ural’s natural minerals in a static regime at certain physicochemical conditions: by the zeolite, montmorillonite and vermiculite in the static conditions. Values of maximum sorption capacity are estimated on a gram of natural sorbents for the present conditions. Comparison of the survey’s results shows that effective sorptions from exploring natural minerals can be used as a clinoptilolite and zeolite-mineral montmorillonite type.

  17. and Cr(VI) ions by chitosan: kinetics and equilibrium studies

    African Journals Online (AJOL)

    The ability of chitosan as an adsorbent for Cu (II) and Cr (VI) ions in aqueous solution was studied. The experiments were done as batch processes. Equilibrium studies were done on both cross-linked and non-cross-linked chitosan for both metals. Cr (VI) adsorption behaviour could be described using the Langmuir ...

  18. Uranium(VI) sorption onto magnetite. Increasing confidence in surface complexation models using chemically evident surface chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Bok, Frank [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Surface Processes

    2017-06-01

    Surface complexation models have made great efforts in describing the sorption of various radionuclides on naturally occurring mineral phases. Unfortunately, many of the published sorption parameter sets are built upon unrealistic or even wrong surface chemistry. This work describes the benefit of combining spectroscopic and batch sorption experimental data to create a reliable and consistent surface complexation parameter set.

  19. The structure of uranium (VI) sorption complexes on silica, alumina, and montmorillonite

    Science.gov (United States)

    Sylwester, E. R.; Hudson, E. A.; Allen, P. G.

    2000-07-01

    We have investigated the adsorption of the uranyl ion (UO 22+) in contact with amorphous silica (SiO 2), γ-alumina (Al 2O 3), and montmorillonite surfaces in the pH range of 3.1-6.5, using X-ray absorption fine structure (XAFS) spectroscopy to observe the local structure around the uranium atom. Analysis shows that in all samples the uranyl ion structure is preserved, with two axial oxygen atoms detected at ca. 1.8 Å. For the montmorillonite samples at low pH a single equatorial oxygen shell is observed at ca. 2.4 Å, with a coordination number of 6 ± 1. At near-neutral pH (6.41) and high ion concentration (0.1 M NaCl), two separate equatorial shells are observed with bond lengths of ca. 2.30 and 2.48 Å. The samples of uranyl on silica and γ-alumina are all observed to have two separate equatorial shells with bond lengths of ca. 2.30 Å and 2.49 Å. A uranium shell at ca. 4.0 Å is observed in the near-neutral pH (˜6.5) samples of uranyl on silica and on γ-alumina. A silicon shell at ca. 3.10 Å is observed in the sample of uranyl on silica at pH 6.5. These results suggest that adsorption of the uranyl ion onto montmorillonite at low pH occurs via ion exchange, leaving the inner-sphere uranyl aquo-ion structure intact. At near-neutral pH and in the presence of a competing cation, inner-sphere complexation with the surface predominates. Adsorption of the uranyl onto the silica and γ-alumina surfaces appears to occur via an inner-sphere, bidentate complexation with the surface, with the formation of polynuclear surface complexes occurring at near-neutral pH.

  20. Effects of complexing compounds on sorption of metal ions to cement

    Energy Technology Data Exchange (ETDEWEB)

    Loevgren, Lars [Umeaa Univ. (Sweden). Inorganic chemistry

    2005-12-15

    This present report is a literature review addressing the effects of complexing ligands on the sorption of radionuclides to solid materials of importance for repositories of radioactive waste. Focus is put on laboratory studies of metal ion adsorption to cement in presence of chelating agents under strongly alkaline conditions. As background information, metal sorption to different mineral and cement phases in ligand free systems is described. Furthermore, surface complexation model (SCM) theories are introduced. According to surface complexation theories these interactions occur at specific binding sites at the particle/water interface. Adsorption of cationic metals is stronger at high pH, and the adsorption of anions occurs preferentially at low pH. The adsorption of ions to mineral surfaces is a result of both chemical bonding and electrostatic attraction between the ions and charged mineral surfaces. By combining uptake data with spectroscopic information the sorption can be explained on a molecular level by structurally sound surface complexation models. Most of the metal sorption studies reviewed are dealing with minerals exhibiting oxygen atoms at their surfaces, mainly oxides of Fe(II,III) and Al(III), and aluminosilicates. Investigations of radionuclides are focused on clay minerals, above all montmorillonite and illite. Which mechanism that is governing the metal ion adsorption to a given mineral is to a large extent depending on the metal adsorbed. For instance, sorption of Ni to montmorillonite can occur by formation of inner-sphere mononuclear surface complexes located at the edges of montmorillonite platelets and by formation of a Ni phyllosilicate phase parallel to montmorillonite layers. Also metal uptake to cement materials can occur by different mechanisms. Cationic metals can both be attached to cement (calcium silicate hydrate, CSH) and hardened cement paste (HCP) by formation of inner-sphere complexes at specific surface sites and by

  1. Adsorption behavior of carboxylated cellulose nanocrystal-polyethyleneimine composite for removal of Cr(VI) ions

    Science.gov (United States)

    Liu, Chao; Jin, Ru-Na; Ouyang, Xiao-kun; Wang, Yang-Guang

    2017-06-01

    In this study, a composite adsorbent (CCN-PEI) composed of carboxylated cellulose nanocrystals (CCN) and polyethyleneimine (PEI) was prepared through an amidation reaction between the carboxyl groups of the CCN and the amine groups of the PEI. The adsorption performance of the CCN-PEI was tested by removing Cr(VI) ions from aqueous solutions. The physicochemical properties of the CCN and the Cr(VI) ion-loaded CCN-PEI were studied using scanning electron microscopy (SEM), transmission electron microscopy, Fourier-transform infrared spectroscopy, and X-ray photoelectron spectroscopy. To investigate the adsorption kinetics of Cr(VI) ions onto this newly developed CCN-PEI, we performed experiments under different adsorption conditions, by varying the contact time, solution pH, initial Cr(VI) ion concentration, and adsorption temperature. The prepared CCN-PEI exhibited an encouraging uptake capacity of 358.42 mg × g-1. The adsorption process was fast: within the first 100 min, Cr(VI) ion adsorption onto the CCN-PEI was about 65%, and the adsorption equilibrium was reached within 250 min. Kinetics experiments indicated that the adsorption process could be described by a pseudo-second-order kinetic model. Furthermore, our adsorption equilibrium data fit the Langmuir isotherms well. The calculated thermodynamic parameters, such as the free energy change (ΔG = -2.93 kJ × mol-1), enthalpy change (ΔH = -5.69 kJ × mol-1), and entropy change (ΔS = -9.14 kJ × mol-1), indicate that the adsorption of Cr(VI) ions onto CCN-PEI was a spontaneous exothermic process. Regeneration tests indicated that CCN-PEI showed good durability and good efficiency for repeated Cr(VI) adsorptions. Based on the results obtained in this work, it can be concluded that CCN-PEI is a potentially effective adsorbent for removing Cr(VI) ions from aqueous solutions.

  2. Sorption Profile of Phosphorus Ions onto ZnO Nanorods Synthesized via Sonic Technique

    Directory of Open Access Journals (Sweden)

    M. F. Elkady

    2016-01-01

    Full Text Available High surface area zinc oxide material in nanorod morphological structure was synthesized using an ultrasonic technique in the presence of polyvinyl pyrrolidone as stabilizing agent. The crystallite, morphology, and surface area of the prepared white powder material were identified using XRD, SEM, and BET techniques, respectively. X-ray analysis confirms the high purity of synthesized ZnO. The evaluated specific surface area of prepared ZnO was 16.7 m2/g; this value guarantees high efficiency for water purification. The feasibility of synthesized ZnO nanorods for phosphorus sorption from aqueous solution was established using batch technique. Nano-zinc oxide exhibits high efficiency for phosphorus removal; the equilibrium state was recorded within 90 minutes. The most effective hydrogen ion concentration of the polluted solution was recorded at pH = 1 for phosphorus decontamination. The equilibrium of phosphorus sorption onto ZnO nanorods was well explained using both Langmuir and Temkin isotherm models. The calculated maximum monolayer sorption capacity was 89 mg/g according to Langmuir isotherm at 27°C. In order to explain the phosphorus sorption mechanism onto the prepared ZnO nanorods, three simplified kinetic models of pseudo-first order, pseudo-second order, and intraparticle diffusion rate models were tested. Kinetics was well fitted by pseudo-second order kinetic model with a contribution of intraparticle diffusion.

  3. Characteristics of cesium ion sorption from aqueous solution on bentonite- and carbon nanotube-based composites.

    Science.gov (United States)

    Yang, Shubin; Han, Cho; Wang, Xiangke; Nagatsu, Masaaki

    2014-06-15

    The technology development of Cs(+) capture from aqueous solution is crucial for the disposal of nuclear waste and still remains a significant challenge. Previous researches have been proven that ion exchanges with the cations and hydroxyl exchange are the main sorption mechanisms for Cs(+). Therefore, how important are the cation exchange and the hydroxyl exchange mechanisms to Cs(+) sorption? And whether can we improve the sorption capacity of the material by increasing the amount of hydroxyl groups? With these in mind, we herein designed the chitosan-grafted carbon nanotubes (CS-g-CNTs) and the chitosan-grafted bentonite (CS-g-bentonite) by plasma-induced grafting method. The interactions of Cs(+) with CNTs, bentonite, CS-g-CNTs and CS-g-bentonite composites were investigated. The sorption of Cs(+) is mainly dominated by strong cation exchange in monovalent Group I and divalent Group II. And the cation-exchange mechanism is much more effective than the hydroxyl group exchange. The effect of hydroxyl groups is dependent on the property of the matrix. We cannot improve the Cs adsorption capacity of material for Cs(+) only by increasing the amount of hydroxyl groups in any case. The spatial structure and the cation-exchange capacity of the material are important factors for choosing the sorbent for Cs(+) removal from radioactive waste water. Copyright © 2014 Elsevier B.V. All rights reserved.

  4. Energy Transfer between U(VI) and Eu(III) Ions Adsorbed on a Silica Surface

    Energy Technology Data Exchange (ETDEWEB)

    Park, K. K.; Cha, W.; Cho, H. R.; Im, H. J.; Jung, E. C.; Song, K. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2011-05-15

    Understanding of chemical behavior of actinide in a groundwater flow is important for assessing the possibility of their migration with water flows in a radioactive waste disposal site. Uranium is ubiquitous in the environment and a major actinide in a nuclear fuel cycle. Americium and curium having isotopes of long half life are minor actinides in a spent fuel. If a minor actinide coexists with uranium in a groundwater flow, some interactions between them could be expected such as minor actinide adsorption onto uranium precipitates and competition with each other for an adsorption to a mineral surface site. Eu(III) ion is frequently used as a chemical analogue of Am(III) and Cm(III) ions in a migration chemistry. The luminescent spectra of U(VI) and Eu(III) ions show a dependency on the coordination symmetry around them, and the changes in intensity or bandwidth of spectra can yield valuable information on their local environment. The luminescent lifetime also strongly depends on the coordination environment, and its measurement is valuable in probe studies on micro-heterogeneous systems. The excited U(VI) ion can be quenched through Stern.Volmer process, hydrolysis of excited species, exciplex formation, electron transfer or energy transfer. In case of U(VI)-Eu(III) system, the interaction between two ions can be studied by measuring the effect of Eu(III) ion on the quenching of U(VI) ion luminescence. There are only a few investigations on the interaction between an excited U(VI) ion and a lanthanide(III) ion. In perchlorate solution, the energy transfer to Eu(III) ion occurred only in solutions of pH>3.87. In this study, the quenching of U(VI) luminescence by Eu(III) on a silica surface was measured. The results will be discussed on the basis of a chemical interaction between them

  5. The effect of salinity on the sorption of cadmium ions from aqueous medium on Fe(III-sepiolite

    Directory of Open Access Journals (Sweden)

    Habish Amal Juma

    2015-01-01

    Full Text Available In this study, the sorption of cadmium ions onto sepiolite modified with hydrated iron(III oxide, Fe(III-sepiolite, has been investigated in natural seawater, artificial seawater, aqueous solution of NaCl of the same ionic strength as the seawater and distilled water. The sorption experiments were performed as a function of the initial solution pH value, the initial metal concentration and the equilibration time, using the batch method. The equilibrium sorption data were analyzed by the Langmuir, Freundlich and Sips isotherm models and the kinetics of sorption was analyzed using the pseudo-first-order and the pseudo-second-order kinetic models. The maximum sorption capacity and the strength of the sorbate-sorbent bonds at initial pH = 7 were found to decrease in the following order: distilled water > NaCl solution > artificial seawater > natural seawater. The values of parameter nS in the Sips model, which fitted the equilibrium sorption results best, showed that heterogeneity of the sorbent surface was the highest in distilled water and the lowest in natural seawater. The sorption kinetic data fitted well with the pseudo-second-order kinetic model, which suggests that the rate-limiting step in Cd2+ sorption onto Fe(III-sepiolite could be chemisorption. The low desorption percentage in both distilled water and 0.001 M HNO3 indicated that sorption occurred mainly by chemisorption mechanisms. [Projekat Ministarstva nauke republike srbije, br. III 45019

  6. Sorption of U(VI) in surfaces of SrTiO{sub 3}; Sorcion de U(VI) en superficies de SrTiO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz O, H.B.; Ordonez R, E.; Fernandez V, S.M. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2004-07-01

    In this work is presented the physico chemical characterization and evaluation of those surface properties and of sorption of U on the SrTiO{sub 3} like possible candidate for contention barrier in the deep geological confinement. The made studies showed that the SrTiO{sub 3} presents maximum levels of sorption of positive nature species (mainly UO{sub 2}{sup 2+} and UO{sub 2}NO{sub 3}{sup +}). (Author)

  7. Investigations of Heavy Metal Ion Sorption Using Nanocomposites of Iron-Modified Biochar

    Science.gov (United States)

    Kołodyńska, D.; Bąk, J.; Kozioł, M.; Pylypchuk, L. V.

    2017-06-01

    Magnetic biochar nanocomposites were obtained by modification of biochar by zero-valent iron. The article provides information on the impact of contact time, initial Cd(II), Co(II), Zn(II), and Pb(II) ion concentrations, dose of the sorbents, solution pH and temperature on the adsorption capacity. On the basis of experiments, it was found that the optimum parameters for the sorption process are phase contact time 360 min (after this time, the equilibrium of all concentrations is reached), the dose of sorbent equal to 5 g/dm3, pH 5 and the temperature 295 K. The values of parameters calculated from the kinetic models and isotherms present the best match to the pseudo second order and Langmuir isotherm models. The calculated thermodynamic parameters ∆H 0, ∆S 0 and ∆G 0 indicate that the sorption of heavy metal ions is an exothermic and spontaneous process as well as favoured at lower temperatures, suggesting the physical character of sorption. The solution of nitric acid(V) at the concentration 0.1 mol/dm3 was the best acidic desorbing agent used for regeneration of metal-loaded magnetic sorbents. The physicochemical properties of synthesized composites were characterized by FTIR, SEM, XRD, XPS and TG analyses. The point characteristics of the double layer for biochar pHPZC and pHIEP were designated.

  8. Metal ion sorption by untreated and chemically treated biomass

    Energy Technology Data Exchange (ETDEWEB)

    Kilbane, J.J.; Xie, J.

    1992-12-31

    The metal-binding ability of biosorbents is well known; however, in comparison with commercial ion-exchange resins the capacity of biosorbents is low. The purpose of this research was to examine chemically modified biosorbents and biosorbents prepared from microorganisms isolated from extreme environments to determine if significant improvements in metal-binding capacity or biosorbents with unique capabilities could be produced. Chemical treatments examined included acid, alkali, carbon disulfide, phosphorus oxychloride, anhydrous formamide, sodium thiosulfate, sodium chloroacetic acid, and phenylsulfonate. Biosorbents were prepared from microorganisms isolated from pristine and acid mine drainage impacted sites and included heterotrophs, methanotrophs, algae, and sulfate reducers. Chemical modification with carbon disulfide, phosphorous oxychloride, and sodium thiosulfate yielded biosorbents with such as much as 74%, 133%, and 155% improvements, respectively, in metal-binding capacity, but the performance of these chemically modified biosorbents deteriorated upon repeated use. A culture isolated from an acid mine drainage impacted site, IGTM17, exhibits about 3-fold higher metal-binding capacity in comparison with other biosorbents examined in this study. IGTM17 also exhibits superior metal-binding ability at decreased pH or in the presence of interfering common cations in comparison with other biosorbents or some commercially available cation exchange resins. Some biosorbents, such as IGTM5, can bind anions. To our knowledge this is the first demonstration of the ability of biosorbents to bind anions. Moreover, preliminary data indicate that the chemical modification of biosorbents may be capable of imparting the ability to selectively bind certain anions. Further research is needed to optimize conditions for the chemical modification and stabilization of biosorbents.

  9. Biosorption of hexavalent chromium (chromium (VI) ion from ...

    African Journals Online (AJOL)

    taye

    2015-04-01

    Apr 1, 2015 ... An experimental effluent analysis was conducted in conjunction with bioremediation process from ... Hexavalent Chromium (Cr (VI) is a by-product released .... Agriculture waste either saw dust or rice husk was procured from. Sabon Gari market, Zaria, Nigeria and brought to the Laboratory for analysis.

  10. Characterization of ZrP{sub 2}O{sub 7} modified with oxalic acid and thermodynamic analysis associated to the uranyl (Vi) sorption; Caracterizacion de ZrP{sub 2}O{sub 7} modificado con acido oxalico y analisis termodinamico asociado a la sorcion de uranilo (VI)

    Energy Technology Data Exchange (ETDEWEB)

    Garcia G, N.; Ordonez R, E. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Solis C, D. A. [Universidad Autonoma del Estado de Mexico, Facultad de Quimica, Paseo Colon y Paseo Tollocan, 50120 Toluca, Estado de Mexico (Mexico); Simoni, E.; Drot, R.; Jeanson, A., E-mail: eduardo.ordonez@inin.gob.mx [Universite Paris-Sud, Institut de Physique Nucleaire, Georges Clemenceau No. 15, Orsay (France)

    2013-10-15

    Several physical and chemical tests were carried out to evaluate the influence of the oxalic acid in the uranium (Vi) sorption on the surface of the zirconium diphosphate. The physical analyses consist of atomic force microscopy (AFM) and total organic coal, and the chemists are the calculation of the reaction heat for the hydrate and sorption processes, the reaction speed constant and the sorption yield in the sodium perchlorate systems and of oxalic acid; these tests allow to corroborate that the oxalic acid influences positively in the uranium (Vi) sorption forming a ternary system of ZrP{sub 2}O{sub 7}/(C{sub 2}O{sub 4})/U(Vi), with a single configuration along the ph interval studied. (Author)

  11. Studies on the Effect pH on the Sorption of Pb(II) and Cu(II) ions from ...

    African Journals Online (AJOL)

    The effect of pH on the sorption of Pb2+ and Cu2+ ion onto Nypa fruticans Wurmb biomass was investigated. Initial pH value of 2, 5, 7, 9, and 12 were used for this study with varying initial concentrations of metal ions. The experimental results were analyzed in terms of Langmuir, Freundlich and Flory-Huggins isotherms.

  12. Adsorption behavior of carboxylated cellulose nanocrystal—polyethyleneimine composite for removal of Cr(VI) ions

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chao; Jin, Ru-Na; Ouyang, Xiao-kun, E-mail: xkouyang@zjou.edu.cn; Wang, Yang-Guang

    2017-06-30

    Highlights: • A carboxylated cellulose nanocrystal-polyethyleneimine composite (CCN-PEI) was prepared. • The as-prepared CCN-PEI was characterized by SEM, TEM, FT-IR, and XPS. • Results suggested that the reusable CCN-PEI could remove Cr(VI) from aqueous solutions with a high adsorption capacity. • The adsorption isotherm, thermodynamics, and kinetics of the adsorption process are also discussed. - Abstract: In this study, a composite adsorbent (CCN-PEI) composed of carboxylated cellulose nanocrystals (CCN) and polyethyleneimine (PEI) was prepared through an amidation reaction between the carboxyl groups of the CCN and the amine groups of the PEI. The adsorption performance of the CCN-PEI was tested by removing Cr(VI) ions from aqueous solutions. The physicochemical properties of the CCN and the Cr(VI) ion-loaded CCN-PEI were studied using scanning electron microscopy (SEM), transmission electron microscopy, Fourier-transform infrared spectroscopy, and X-ray photoelectron spectroscopy. To investigate the adsorption kinetics of Cr(VI) ions onto this newly developed CCN-PEI, we performed experiments under different adsorption conditions, by varying the contact time, solution pH, initial Cr(VI) ion concentration, and adsorption temperature. The prepared CCN-PEI exhibited an encouraging uptake capacity of 358.42 mg × g{sup −1}. The adsorption process was fast: within the first 100 min, Cr(VI) ion adsorption onto the CCN-PEI was about 65%, and the adsorption equilibrium was reached within 250 min. Kinetics experiments indicated that the adsorption process could be described by a pseudo-second-order kinetic model. Furthermore, our adsorption equilibrium data fit the Langmuir isotherms well. The calculated thermodynamic parameters, such as the free energy change (ΔG = −2.93 kJ × mol{sup −1}), enthalpy change (ΔH = −5.69 kJ × mol{sup −1}), and entropy change (ΔS = −9.14 kJ × mol{sup −1}), indicate that the adsorption of Cr(VI) ions onto CCN

  13. Sorption of radioactive cesium and barium ions onto solid humic acid

    Energy Technology Data Exchange (ETDEWEB)

    Celebi, O., E-mail: celebi@vt.edu [Department of Chemistry, Macromolecular Science and Engineering, Virginia Tech, Blacksburg, VA 24061 (United States); Kilikli, A. [Department of Chemistry, Middle East Technical University, 06530 Ankara (Turkey); Erten, H.N. [Department of Chemistry, Bilkent University, 06800 Bilkent, Ankara (Turkey)

    2009-09-15

    In this study, the sorption behavior of two important fission product radionuclides ({sup 137}Cs and {sup 140}Ba) onto sodium form of insolubilized humic acid (INaA) were investigated as a function of time, cation concentration and temperature, utilizing the radiotracer method. The sorption processes are well described by both Freundlich and Dubinin-Radushkevich type isotherms. Thermodynamic constants such as; free energy ({Delta}G{sub ads}), enthalpy ({Delta}H{sub ads}), entropy ({Delta}S{sub ads}) of adsorption were determined. It was found that Ba{sup 2+} was adsorbed five times more than Cs{sup +} onto structurally modified humic acid and kinetic studies indicated that adsorption behavior of both ions obey the pseudo second order rate law. The effect of pH change on sorption was also examined. FTIR and solid-state carbon NMR ({sup 13}CNMR) spectroscopic techniques were used to understand the structural changes during insolubilization process. Quantitative determination of adsorption sites was carried out using potantiometric titration.

  14. Sorption of heavy metal ions on new metal-ligand complexes chemically derived from Lycopodium clavatum

    Energy Technology Data Exchange (ETDEWEB)

    Pehlivan, E.; Ersoz, M.; Yildiz, S. [Univ. of Selcuk, Konya (Turkey); Duncan, H.J. [Univ. of Glasgow, Scotland (United Kingdom)

    1994-08-01

    Sorption of heavy metal ions from aqueous solution has been investigated as a function of pH using a novel exchanger system whereby Lycopodium clavatum is functionalized with carboxylate and glyoxime metal-ligand complexes. The new ligand exchangers were prepared using a reaction of diaminosporopollenin with various metal-ligand complexes of glyoxime and monocarboxylic acid. The sorptive behavior of these metal-ligand exchangers and the possibilities to remove and to recover selectively heavy metal cations using these systems are discussed on the basis of their chemical natures and their complexing properties.

  15. Spectrophotometric study of neptunium (VI) complexation by nitrate ions; Etude par spectrophotometrie de la complexation du neptunium au degre d'oxydation (VI) par les ions nitrates

    Energy Technology Data Exchange (ETDEWEB)

    Pochon, P. [CEA/VALRHO - site de Marcoule, Dept. de Recherche en Retraitement et en Vitrification (DRRV), 30 - Marcoule (France)]|[Conservatoire National des Arts et Metiers (CNAM), 75 - Paris (France)]|[Centre Regional Associe de Lyon, 69 (France)

    2000-07-01

    Neptunium(VI) complexation by nitrate ions was investigated by visible and near-infrared spectrophotometry, a technique suitable for observing the appearance and evolution of the species in solution. In the absence of reference spectra for Np(VI) nitrate- complexes, mathematical (factor analysis) tools were used to interpret the spectra. These chemo-metric techniques were first tested and validated on a simpler chemical system: Np(VI)complexation by the SiW{sub 11}O{sub 39}{sup 8-} anion. The test media used to investigate Np(VI) nitrate- complexes generally contain nitrate and perchlorate salts at high concentrations (high ionic strength). Media effects arising from the presence of cations, acidity or the perchlorate ion concentration are therefore significant, and no doubt account for the scattered values of the complexation constants published in the literature. The evolution of the neptunium spectra according to the parameters of the reaction medium illustrated these effects and allowed them to be quantified by a global 'perturbation constant'. In order to minimize the spectrum modifications due to media effects, the neptunium nitrate-complexes were studied at constant ionic strength in weak acidic media (2 mol.kg{sup -1}{sub H2O}) in the presence of sodium salts. The bulk formation constants and the spectrum of the NpO{sub 2}(NO{sub 3}){sup +} complex were determined for ionic strength values of 2.2, 4, 6 and 8 mol.kg{sup -1}{sub H2O}. The constants remained on the same order of magnitude regardless of the ionic strength; the thermodynamic constant {beta}{sub 1}{sup 0} determined from them according to specific interaction theory is thus probably of little significance. Conversely, the bulk constants can be corrected for the effects of the perchlorate ions by taking the global 'perturbation constant' into account. (author)

  16. Sorption of Uranium Ions from Their Aqueous Solution by Resins Containing Nanomagnetite Particles

    Directory of Open Access Journals (Sweden)

    Mahmoud O. Abd El-Magied

    2016-01-01

    Full Text Available Magnetic amine resins composed of nanomagnetite (Fe3O4 core and glycidyl methacrylate (GMA/N,N′-methylenebisacrylamide (MBA shell were prepared by suspension polymerization of glycidyl methacrylate with N,N′-methylenebisacrylamide in the presence of nanomagnetite particles and immobilized with different amine ligands. These resins showed good magnetic properties and could be easily retrieved from their suspensions using an external magnetic field. Adsorption behaviors of uranium ions on the prepared resins were studied. Maximum sorption capacities of uranium ions on R-1 and R-2 were found to be 92 and 158 mg/g. Uranium was extracted successfully from three granite samples collected from Gabal Gattar pluton, North Eastern Desert, Egypt. The studied resins showed good durability and regeneration using HNO3.

  17. Adsorption studies for the removal of Cr(VI) ion from aqueous solution

    African Journals Online (AJOL)

    The adsorption characteristics of Cr(VI) in the form of Cr2O7(-2) ion from aqueous solution onto synthetic exchanger Amberlite IRA 400(Cl) resin was studied from UV – visible spectrphotometric measurement using DPC at 580nm. The efficiency of the adsorbent was judged from the variation of the % adsorption with (i) ...

  18. Struvite recovery from solution containing phosphate(V and sulphate(VI ions

    Directory of Open Access Journals (Sweden)

    Hutnik Nina

    2015-07-01

    Full Text Available The research results concerning the application of magnesium and ammonium ions for continuous removal of phosphate(V ions from solution containing 1.0 or 0.20 mass% of PO43– and from 0.10 to 0.50 mass% of SO42– are presented. A continuous struvite MgNH4PO4 × 6H2O reaction crystallization process was carried out both under stoichiometric conditions and using 20% excess of magnesium ions. The research was conducted in a DT MSMPR type crystallizer with internal circulation of suspension driven by a propeller stirrer, in constant temperature 298 K. The pH varied from 9 to 11 and mean residence time of suspension in a crystallizer τ varied from 900 to 3600 s. It was concluded, that sulphate(VI ions influenced product quality disadvantageously. Depending on process parameter combinations struvite crystals of mean size from ca. 18 to ca. 44 μm and of moderate homogeneity: CV 7–95% were produced. Presence of sulphate(VI ions favored crystallization of struvite as prismatic crystals, but tubular forms were also identified. The best shaped struvite crystals were produced at relatively low concentration of sulphate(VI ions, pH 9 and for mean residence time of suspension in a crystallizer elongated up to 3600 s.

  19. Sorption of micropollutant estrone to a water treatment ion exchange resin.

    Science.gov (United States)

    Neale, Peta A; Mastrup, Maibritt; Borgmann, Thomas; Schäfer, Andrea I

    2010-01-01

    Micropollutants occur in natural waters from a range of sources. Estrogenic compounds are naturally excreted by humans and hence stem predominantly from wastewater effluents. Due to their small molecular weight and concentration their effective control is a challenge. In this study magnetic ion exchange (MIEX), which was developed to remove natural organic matter (NOM) from surface water, was investigated for such a micropollutant, estrone. The interaction of estrone with the resin occurs as a side effect when NOM is removed. This interaction results in some degree of removal. However, the accumulation of those hazardous materials on the resin, which can be associated with accidental release, as well as the concentration in the regeneration brine of the process, is environmentally more significant. For this reason a thorough investigation of interaction phenomena was undertaken. Estrone and polymeric materials (such as ion exchange resins or membranes) interact through a number of mechanisms including specific and non-specific interactions. Sorption and desorption of estrone were studied as a function of pH, temperature, natural organic matter concentration, sulfate concentration and ionic strength to elucidate possible mechanisms. The results demonstrated that the resin removed around 70% estrone at high pH conditions (>10.4) when estrone was predominantly negatively charged. However, below pH 10.4, when estrone was neutral, approximately 40% of estrone still sorbed due to hydrogen bonding. The optimum temperature for estrone sorption was observed to be in the 15 to 35 degrees C range, while the presence of other anions, including natural organic matter reduced estrone removal due to competition for anion exchange sites. Desorption of estrone was most effective with 2 M NaCl regeneration brine concentration when estrone was negatively charged (98% desorption). However, when estrone was neutral there was no significant difference between 1 M and 2 M NaCl. The

  20. Formation of crystalline PuO2+x·nH2O nanoparticles upon sorption of Pu(V,VI) onto hematite

    Science.gov (United States)

    Romanchuk, Anna Yu.; Kalmykov, Stepan N.; Egorov, Alexander V.; Zubavichus, Yan V.; Shiryaev, Andrey A.; Batuk, Olga N.; Conradson, Steven D.; Pankratov, Denis A.; Presnyakov, Igor A.

    2013-11-01

    It has been recognized that natural aquatic colloids can readily sorb actinide elements, including plutonium, whose behavior is complicated by its multiple valence states and the possibility of redox reactions under environmental conditions. In this paper, the sorption and surface-mediated redox transformations of hexavalent plutonium on synthetic well-characterized hematite colloids are studied in a series of batch sorption experiments. The variation in the kinetics of the Pu-hematite interactions, Pu-L3-XAFS, and HRTEM over a broad range of total concentrations of Pu have been studied in an attempt to define the molecular-level speciation of Pu. The surface-mediated slow reduction of Pu(V/VI) results in the formation of crystalline nanoparticles of PuO2+x·nH2O approximately 1.5 nm in size at [Pu]tot ⩾ 10-9 M. This result is confirmed independently by HRTEM images of Pu-containing particles and through the identification in the EXAFS of a Pu neighbor shell at 3.8 Å. The formation of such nanoparticles potentially influences the colloid-mediated transport of Pu in the subsurface environment because of the very slow leaching of Pu from the hematite colloids.

  1. Dynamics of oxygen sorption from water by copper-containing fibrous porous redox ion-exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Ul' eva, L.S.; Burinskii, S.V.; Grebennikov, S.F.

    1985-08-10

    A most important field of practical application of oxidation-reduction (redox) polymers is the sorption of dissolved oxygen from water in order to prevent corrosion of power equipment. Copper-containing redox polymers, which have fairly high capacity and good swelling characteristics were used. Values of the dynamic exchange capacity (DEC) for copper ions, the redox capacity (ROC) for the reducing metal, and the dynamic reduction capacity for oxygen are given. It can be seen from these data that fibrous porous reactive materials (FPRM) in which the mass fiber content is 60% have somewhat better characteristics. The authors conclude that despite the fibrous porous material's considerably lower coefficient of internal diffusion, it is superior to granular EI-21 in the length of the masstransfer zone and in the coefficient of utilization of capacity, in consequence of the low linear density of the fibers. Their mass transfer zone is shorter by a factor of about 5.

  2. Biosorption of Cr(VI from Aqueous Solution Using Murraya koenigii (Curry tree Stems

    Directory of Open Access Journals (Sweden)

    Selvaraj Suresh

    2016-12-01

    Full Text Available In the present work, the sorption capacity of Murraya Koenigii Stems (MKST, an agricultural waste, is identified for the removal of Cr(VI from aqueous solution and the effect of different process parameters likes pH and adsorbent dosage were studied. pH 1 is observed to be the optimum pH for Cr(VI sorption onto the biosorbent. The equilibrium data of Cr(VI sorption fit well with the Langmuir model with a monolayer sorption capacity of 12.25 mg/g. The results show that the metal ion interacts strongly with the biosorbent and can be effectively used in the removal of Cr(VI from aqueous solution. DOI: http://dx.doi.org/10.17807/orbital.v0i0.867

  3. Ultra-trace recognition and removal of toxic chromium (VI) ions from water using visual mesocaptor.

    Science.gov (United States)

    Shenashen, Md A; Shahat, A; El-Safty, Sherif A

    2013-01-15

    The key to designing optical mesocaptors is to construct a chromogenic receptor, namely, diphenylcarbazide (DPC), as a nanoscale platform scavenger with different functional characteristics, such as density, accessibility, and intrinsic mobility. Engineering of optical captors allows facile and reliable signaling in continuous monitoring modes, and enables simple and high-speed removal of toxic chromium (VI) ions. Mesoporous aluminosilica monoliths, with unique morphologies, active surface sites, and physical properties, enhance sensing/removal characteristics in terms of sensitivity, selectivity, and response time. The systematic design of optical mesocaptor is based on a densely patterned selective binding site (DPC) in engineered mesocylinder carriers that have multidirectional pores and microsized particle-like monoliths to control the adsorption/detection assays of Cr(VI) ions. Synthetic mesocaptor can be used for visual removal of Cr(VI) ions even at low concentration levels of 10(-10)M (i.e., 0.07 ppb) with rapid response time in minutes. Moreover, these new classes of design-made hybrid mesocaptor exhibit long-term signaling stability and recognition functionalities that provided extraordinary sensitivity, selectivity, reusability, and fast kinetic detection and quantification of various deleterious metal ions in the environment. Copyright © 2012 Elsevier B.V. All rights reserved.

  4. Electrospinning synthesis of porous Al{sub 2}O{sub 3} nanofibers by pluronic P123 triblock copolymer surfactant and properties of uranium (VI)-sorption

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Bo [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Department of Applied Chemistry Engineering, Jilin Vocational College of Industry and Technology, Jilin 132013 (China); Institute of Petrochemistry Heilongjiang Academy of Sciences, Harbin 150001 (China); Fan, Meiqing [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Department of Applied Chemistry Engineering, Jilin Vocational College of Industry and Technology, Jilin 132013 (China); Tan, Lichao [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Li, Rumin, E-mail: lirumin@hrbeu.edu.cn [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Song, Dalei; Liu, Qi [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Wang, Jun, E-mail: zhqw1888@sohu.com [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Institute of Advanced Marine Materials, Harbin Engineering University, Harbin 150001 (China); Zhang, Bin [Institute of Petrochemistry Heilongjiang Academy of Sciences, Harbin 150001 (China); Jing, Xiaoyan [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China)

    2016-07-01

    Porous Alumina (Al{sub 2}O{sub 3}) nanofibers were prepared by electrospinning process using pluronic P123 triblock copolymer surfactant as template. The characterizations of the adsorbent were investigated by X-ray diffraction (XRD) fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and nitrogen adsorption–desorption. The obtained nanofibers were used as adsorbents for the removal of Uranium (VI). The maximum adsorption occurred at pH 5, the equilibrium adsorption amount was about 87 mg/g, and the equilibrium time was 6.0 h. A pseudo-second order model could best describe adsorption kinetics. The adsorption equilibrium data fit Freundlich adsorption isotherm equation well. Thermodynamic parameters such as standard enthalpy (ΔH{sup 0}), standard entropy (ΔS{sup 0}), standard free energy (ΔG{sup 0}) and activation energy (E{sub a}) were calculated. The results predict an endothermic nature of adsorption and a spontaneous process. - Highlights: • The porous Al{sub 2}O{sub 3} nanofibers were used for U(VI)-sorption for the first time. • The adsorption process was endothermic and spontaneous. • The maximum adsorption capacity was 87 mg g{sup −1} at 25 °C.

  5. A High Capacity Li-Ion Cathode: The Fe(III/VI Super-Iron Cathode

    Directory of Open Access Journals (Sweden)

    Stuart Licht

    2010-05-01

    Full Text Available A super-iron Li-ion cathode with a 3-fold higher reversible capacity (a storage capacity of 485 mAh/g is presented. One of the principle constraints to vehicle electrification is that the Li-ion cathode battery chemistry is massive, and expensive. Demonstrated is a 3 electron storage lithium cathodic chemistry, and a reversible Li super-iron battery, which has a significantly higher capacity than contemporary Li-ion batteries. The super-iron Li-ion cathode consists of the hexavalent iron (Fe(VI salt, Na2FeO4, and is formed from inexpensive and clean materials. The charge storage mechanism is fundamentally different from those of traditional lithium ion intercalation cathodes. Instead, charge storage is based on multi-electron faradaic reduction, which considerably enhances the intrinsic charge storage capacity.

  6. Kinetic Modelling of the Removal of Multiple Heavy Metallic Ions from Mine Waste by Natural Zeolite Sorption

    Directory of Open Access Journals (Sweden)

    Amanda L. Ciosek

    2017-07-01

    Full Text Available This study investigates the sorption of heavy metallic ions (HMIs, specifically lead (Pb2+, copper (Cu2+, iron (Fe3+, nickel (Ni2+ and zinc (Zn2+, by natural zeolite (clinoptilolite. These HMIs are combined in single-, dual-, triple-, and multi-component systems. The batch mode experiments consist of a total initial concentration of 10 meq/L normality for all systems, acidified to a pH of 2 by concentrated nitric (HNO3 acid. A zeolite dosage of 4 g per 100 mL of synthetic nitrate salt aqueous solution is applied, for a contact period of 5 to 180 min. Existing kinetic models on HMIs sorption are limited for multi-component system combinations. Therefore, this study conducts kinetic analysis by both reaction and diffusion models, to quantify the sorption process. The study concludes that the process correlates best with the pseudo-second-order (PSO kinetic model. In the multi-component system combining all five HMIs, the initial sorption rate and theoretical equilibrium capacity are determined as 0.0033 meq/g·min and 0.1159 meq/g, respectively. This provides significant insight into the mechanisms associated with the sorption process, as well as contributing to the assessment of natural zeolite as a sorbent material in its application in industrial wastewater treatment.

  7. Transportation and kinetic analysis of Mo(VI) ions through a MDLM system containing TNOA as carrier.

    Science.gov (United States)

    Donat, R; Durmaz, Ö; Cetişli, H

    2015-08-30

    In this report, Mo(VI) ions are transported from an aqueous donor phase into an aqueous acceptor phase by a newly designed method called as multi dropped liquid membrane (MDLM) system prepared by dissolving TNOA as carrier in kerosene. During the extraction of Mo(VI) ions by the liquid membrane system; 100ppm Mo(VI) solutions as donor phase, buffer solution(pH:9.5) and Na2CO3 in different concentrations as acceptor phase and TNOA diluted by kerosen as organic phase are used.In our experimental work, the effect of temperature by using buffer solution and Na2CO3 in the acceptor phase and effect of concentration of acceptor phase on the extraction of Mo(VI) ions were investigated. Appropriate conditions for Mo(VI) transportation were as follows: pH of donor phase is 2.00, concentration of TNOA is 0.005M, 1.00M Na2CO3 as acceptor phase, and flux rate is 50mL/min. Besides, Mo(VI) ion transportation is consecutive first order irreversible reaction and the transportation of Mo(VI) ions is diffusion controlled process. The kinetic parameters (k1, k2, Rm(max), tmax, Jd(max), Ja(max)) were calculated for the interface reactions assuming two consecutive, irreversible first-order reactions. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. Higher adsorption capacity of Spirulina platensis alga for Cr(VI) ions removal: parameter optimisation, equilibrium, kinetic and thermodynamic predictions.

    Science.gov (United States)

    Gunasundari, Elumalai; Senthil Kumar, Ponnusamy

    2017-04-01

    This study discusses about the biosorption of Cr(VI) ion from aqueous solution using ultrasonic assisted Spirulina platensis (UASP). The prepared UASP biosorbent was characterised by Fourier transform infrared spectroscopy, X-ray diffraction, Brunauer-Emmet-Teller, scanning electron spectroscopy and energy dispersive X-ray and thermogravimetric analyses. The optimum condition for the maximum removal of Cr(VI) ions for an initial concentration of 50 mg/l by UASP was measured as: adsorbent dose of 1 g/l, pH of 3.0, contact time of 30 min and temperature of 303 K. Adsorption isotherm, kinetics and thermodynamic parameters were calculated. Freundlich model provided the best results for the removal of Cr(VI) ions by UASP. The adsorption kinetics of Cr(VI) ions onto UASP showed that the pseudo-first-order model was well in line with the experimental data. In the thermodynamic study, the parameters like Gibb's free energy, enthalpy and entropy changes were evaluated. This result explains that the adsorption of Cr(VI) ions onto the UASP was exothermic and spontaneous in nature. Desorption of the biosorbent was done using different desorbing agents in which NaOH gave the best result. The prepared material showed higher affinity for the removal of Cr(VI) ions and this may be an alternative material to the existing commercial adsorbents.

  9. Effect of Cr(VI) concentration on gas and particle production during iron oxidation in aqueous solutions containing Cl- ions.

    Science.gov (United States)

    Ahn, Hyangsig; Jo, Ho Young; Ryu, Ji-Hun; Koh, Yong-Kwon

    2017-02-01

    Zero-valent iron (ZVI) is commonly used as a medium in permeable reactive barriers (PRBs) because of its high reducing ability. The generation of H2 gas in PRBs, however, can decrease the permeability of PRBs and reduce the contact area between the PRB and contaminated groundwater. This study investigated the effect of the initial Cr(VI) concentration ([Cr(VI)init]) in aqueous solutions containing Cl- ions on the generation of H2 gas. ZVI chips were reacted in reactors with 0.5-M NaCl solutions with [Cr(VI)init] ranging between 51 and 303 mg/L. The initial pH was set at 3. The oxidation of ZVI chips by Cr(VI) in aqueous solutions containing Cl- ions produced H2 gas and particles (Fe(III)-Cr(III)(oxy)hydroxides). The Cr(VI) removal from aqueous solutions increased as the [Cr(VI)init] increased, as did H2 gas generation. The positive effect of [Cr(VI)init] on H2 gas generation might be due to an increase in the redox potential gradient as [Cr(VI)init] increases. This increased gradient would enhance H+ ion penetration through the passive film (Fe(III)-Cr(III)(oxy)hydroxides), which formed on the ZVI surface, by diffusion from the solution to pits beneath the passive film.

  10. Spectroscopic investigations on sorption of uranium onto suspended bentonite. Effects of pH, ionic strength and complexing anions

    Energy Technology Data Exchange (ETDEWEB)

    Verma, Parveen Kumar; Pathak, Priyanath; Mohapatra, Manoj; Mohapatra, Prasanta Kumar [Bhabha Atomic Research Centre, Mumbai (India). Radiochemistry Div.; Yadav, Ashok Kumar; Jha, Sambhunath; Bhattacharyya, Dibyendu [Bhabha Atomic Research Centre, Mumbai (India). Atomic and Molecular Physics Div.

    2015-06-01

    Batch sorption experiments were carried out under aerobic conditions to understand the sorption behavior of U(VI) onto bentonite clay under varying pH (2-8) and ionic strength (I = 0.01 - 1 M (NaClO{sub 4})) conditions. The influences of different complexing anions (1 x 10{sup -4} M) such as oxalic acid (ox), carbonate (CO{sub 3}{sup 2-}), citric acid (cit), and humic acid (HA, 10 mg/L) on the sorption behavior were also investigated. The sorption of U(VI) increased with increasing pH up to pH 6 beyond which a decrease was attributed to the formation of anionic carbonate species. Marginal influence of the change in the ionic strength of the medium on the sorption profile of uranium suggested inner-sphere complexation onto the bentonite surface. The presence of humic acid showed interesting sorption profile with varying pH. Initially, there was an enhancement in the sorption with increased pH followed by a plateau and finally a decrease thereafter due to the formation of aqueous U(VI)-humate complexes. Spectroscopic studies such as UV spectrophotometry, luminescence and extended X-ray absorption fine structure (EXAFS) measurements were also performed to understand the changes in aqueous speciation of U(VI) ion. The luminescence yields of different aqueous U(VI) species followed the order: U(VI){sub Hydroxy} > U(VI){sub HumicAcid} > U(VI){sub carbonate} > U(VI){sub citrate}. The lower luminescence yield of U(VI)carbonate complex can be attributed to the strong dynamic quenching by carbonate at room temperature. The U(VI) samples shows two distinct life-time suggesting the presence of the different luminescent U(VI) species. Similar trend was observed for U(VI)-bentonite suspension in presence/absence of the complexing ligands. There was luminescence quenching for the sorbed U(VI) due to surface complexation. These observations were further supported by spectrophotometric measurements. EXAFS spectra of U(VI) samples were recorded in luminescence mode at the U L{sub 3

  11. Effects of common groundwater ions on chromate removal by magnetite: importance of chromate adsorption

    National Research Council Canada - National Science Library

    Meena, Amanda H; Arai, Yuji

    2016-01-01

    .... In this study, effects of common groundwater ions (i.e., nitrate and sulfate) on Cr(VI) sorption to magnetite were investigated using batch geochemical experiments in conjunction with X-ray absorption...

  12. Strontium (Sr) separation from seawater using titanate adsorbents: Effects of seawater matrix ions on Sr sorption behavior

    Science.gov (United States)

    Ryu, Jungho; Hong, Hye-jin; Ryu, Taegong; Park, In-Su

    2017-04-01

    Strontium (Sr) which has many industrial applications such as ferrite magnet, ceramic, and fire works exists in seawater with the concentration of approximately 7 mg/L. In previous report estimating economic potential on recovery of various elements from seawater in terms of their commercial values and concentrations in seawater, Sr locates upper than approximate break-even line, which implies Sr recovery from seawater can be potentially profitable. Recently, Sr separation from seawater has received great attention in the environmental aspect after Fukushima Nuclear Power Plant (NPP) accident which released much amount of radioactive Sr and Cs. Accordingly, the efficient separation of radioactive elements released to seawater has become critical as an important technological need as well as their removal from radioactive wastes. So far, it has been introduced to separate Sr from aqueous media by various methods including solvent extraction, adsorption by solid materials, and ion exchange. Among them, the adsorption technique using solid adsorbents is of great interest for selectively separating Sr from seawater with respect to low concentration level of Sr. In this study, we synthesized titanate nanotube (TiNT) by simple hydrothermal reaction, characterized its physicochemical properties, and systematically evaluated Sr sorption behavior under various reaction conditions corresponding to seawater environment. The synthesized TiNT exhibited the fibril-type nanotube structure with high specific surface area of 260 m2/g. The adsorption of Sr on TiNT rapidly occurred following pseudo-second-order kinetic model, and was in good agreement with Langmuir isotherm model, indicating maximum adsorption capacity of 97 mg/g. Based on Sr uptake and Na release with stoichiometric balance, sorption mechanism of Sr on TiNT was found to be ion-exchange between Na in TiNT lattice and Sr in solution phase, which was also confirmed by XRD and Raman analysis. Among competitive ions, Ca

  13. Binary Component Sorption of Cadmium, and Copper Ions onto Yangtze River Sediments with Different Particle Sizes

    Directory of Open Access Journals (Sweden)

    Jianxin Fan

    2017-11-01

    Full Text Available Sorption is a crucial process that influences immobilization and migration of heavy metals in an aqueous environment. Sediments represent one of the ultimate sinks for heavy metals discharged into water body. Moreover, the particle size of sediments plays an extremely important role in the immobilization of heavy metals. In this study, the sorption and desorption of cadmium (Cd and copper (Cu onto sediments with different particle sizes were investigated to predict the rate and capacity of sorption, to understand their environmental behaviors in an aqueous environment. Batch sorption and kinetic experiments were conducted to obtain the retained amount and rate of Cd and Cu in a binary system. Experimental data were simulated using sorption models to ascertain the sorption capacity and the kinetic rate. Results of European Communities Bureau of Reference (BCR sequential extraction showed the highest concentration of Cd (0.344 mg kg−1, and its distribution varied with sediment particle size and site. Furthermore, most of Cu (approximately 57% to 84% existed as a residual fraction. The sorption of Cu onto six sediments followed a pseudo-first order reaction, whereas that of Cd followed a pseudo-second order reaction. Additionally, the competitive Langmuir model fitted the batch sorption experimental data extremely well. The highest sorption capacities of Cd and Cu reach 0.641 mmol kg−1 and 62.3 mmol kg−1, respectively, on the smallest submerged sediment particles. The amounts of Cu and Cd desorbed (mmol kg−1 increased linearly with the initial concentration increasing. Thus, sediment texture is an important factor that influences the sorption of heavy metal onto sediments.

  14. Preparation of magnetic core-shell iron oxide@silica@nickel-ethylene glycol microspheres for highly efficient sorption of uranium(VI).

    Science.gov (United States)

    Tan, Lichao; Zhang, Xiaofei; Liu, Qi; Wang, Jun; Sun, Yanbo; Jing, Xiaoyan; Liu, Jingyuan; Song, Dalei; Liu, Lianhe

    2015-04-21

    We report a facile approach for the formation of magnetic core-shell iron oxide@silica@nickel-ethylene glycol (Fe3O4@SiO2@Ni-L) microspheres. The structure and morphology of Fe3O4@SiO2@Ni-L are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and nitrogen sorption isotherm. The composite possesses a high specific surface area of 382 m(2) g(-1). The obtained core/shell structure is composed of a superparamagnetic core with a strong response to external fields, which are recovered readily from aqueous solutions by magnetic separation. When used as the adsorbent for uranium(vi) in water, the as-prepared Fe3O4@SiO2@Ni-L multi-structural microspheres exhibit a high adsorption capacity, which is mainly attributed to the large specific surface area and typical mesoporous characteristics of Fe3O4@SiO2@Ni-L microspheres. This work provides a promising approach for the design and synthesis of multifunctional microspheres, which can be used for water treatment, as well as having other potential applications in a variety of biomedical fields including drug delivery and biosensors.

  15. Biosorption of Cr(III), Cr(VI), Cu(II) ions by intact cells of Spirulina platensis

    OpenAIRE

    Gelagutashvili, E.; Bagdavadze, N.; Rcheulishvili, A.

    2017-01-01

    The absorption characteristics of Cr(III), Cr(VI), Cu(II) ions on intact living cells Spirulina platensis (pH9.6) were studied by using a UV-VIS spectrophotometer. Also biosorption of these ions with cyanobacteria Spirulina platensis were studied using equilibrium dialysis and atomic absorption analysis.It was shown, that the absorption intensity of Spirulina platensis decreases, when Cr(III), Cr(VI), Cu(II) ions are added. Significant difference between the absorption intensity for Cu(II) Sp...

  16. Kinetic and equilibrium study for the sorption of Pb(II ions from aqueous phase by water hyacinth (Eichhornia crassipes

    Directory of Open Access Journals (Sweden)

    Gerald. K. Muthakia

    2012-08-01

    Full Text Available This paper reports the kinetic and equilibrium studies of Eichhornia crassipes root biomass as a biosorbent for Pb(II ions from aqueous system. Batch adsorption studies were carried out to examine the influence of various parameters such as the pH, contact time, adsorbent dose, initial metal ion concentration, temperature and agitation speed on the metal ion uptake. Uptake of Pb(II ions on the E. crassipes roots showed a pH-dependent profile. The maximum metal uptake values were 164 μg/mL. Langmuir model fitted the experimental sorption equilibrium data with a good fit (R2 › 0.99. The biosorption kinetics was described by the pseudo-second-order model (R2 › 0.99.DOI: http://dx.doi.org/10.4314/bcse.v26i2.3

  17. Reduction of the U(VI) ion. A fast conductimetry study

    Energy Technology Data Exchange (ETDEWEB)

    Broszkiewicz, R.K. (Institute of Nuclear Chemistry and Technology, Warsaw (Poland)); Vojnovic, B.; Michael, B.D. (Mount Vernon Hospital, Northwood (UK). Gray Lab.)

    1991-01-01

    The reduction of U(VI) by e{sub aq}{sup -} was followed by means of fast conductimetry in acid and conductimetry and spectrophotometry in alkaline solutions. In alkaline solutions, the biomolecular rate constant of reaction between UO{sub 4}{sup 2-} and e{sub aq}{sup -} was determined. Analytical methods applied in this work were too fast to follow the slow disproportionation of produced U(V)-ion, but it has been observed that in alkaline solutions it probably goes via a dimeric ion (U(V)){sub 2}, which protonates with a rate {kappa}{sub 7} = 1.30 x 10{sup 5}s{sup -1}. (author).

  18. Reduction of the U(VI) ion. A fast conductimetry study

    Science.gov (United States)

    Broszkiewicz, Roman K.; Vojnovic, Borivoj; Michael, Barry D.

    The reduction of U(VI) by e -aq was followed by means of fast conductimetry in acid and conductimetry and spectrophotometry in alkaline solutions. In alkaline solutions, the biomolecular rate constant of reaction between UO 2-4 and e -aq was determined as k4=4.50×10 9M -1s -1. In acid solutions it has been observed that the analogous rate is within a range 1.7×10 10< k9<7.4×10 10M -1s -1 for the reaction between UO 2+2 and e -aq. Analytical methods applied in this work were too fast to follow the slow disproportionation of produced U(V)-ion, but it has been observed that in alkaline solutions it probably goes via a dimeric ion [U(V)] 2, which protonates with a rate k7=1.30 ×10 5s-1.

  19. Effect of high ionic strength on the extraction of uranium(VI ions

    Directory of Open Access Journals (Sweden)

    M.K. Nazal

    2014-01-01

    Full Text Available Preparation and characterization of didodecylphosphoric acid (HDDPA as an extractant in toluene was carried. Mass spectroscopy showed that the monomer peak at 457.4 amu [M–Na+] is double that of the dimer at 891.9 amu [M–M–Na+] and the monomer molecules concentration dominate the dimer molecules in toluene. HDDPA was used as an extractant for the extraction of U(VI ion from perchlorate and nitrate media that have ionic strength (1.00, 3.00, 5.00, 7.00 M. The effect of HDDPA concentration, pcH, ionic strength of supporting electrolytes, and temperature in the range 15–45 °C on the extraction process have been studied. The stoichiometry of the extraction of U(VI ion, the free energy change (ΔG, the enthalpy change (ΔH, the entropy change (ΔS, and Kex at different ionic strength have been calculated. The formula of the complexes, which were formed has been established to be UO2(X(R2(HR2 at pcH equal 2.00 and UO2(X(R2(HR2 and UO2(X(R2 at pcH = 1.00, where (X isClO4- orNO3- and (HR2 is didodecylphosphoric acid monomer, (R2 is the deprotonated didodecylphosphoric acid, where R is the dodecyl group.

  20. Sorption of Ni(II) on GMZ bentonite: Effects of pH, ionic strength, foreign ions, humic acid and temperature

    Energy Technology Data Exchange (ETDEWEB)

    Yang Shitong [School of Nuclear Science and Engineering, North China Electric Power University, Beijing 102206 (China); Key Lab of Novel Thin Film Solar Cells, Institute of Plasma Physics, Chinese Academy of Sciences, P.O. Box 1126, 230031 Hefei (China); Li Jiaxing; Lu Yi [Key Lab of Novel Thin Film Solar Cells, Institute of Plasma Physics, Chinese Academy of Sciences, P.O. Box 1126, 230031 Hefei (China); Chen Yixue [School of Nuclear Science and Engineering, North China Electric Power University, Beijing 102206 (China); Wang Xiangke [School of Nuclear Science and Engineering, North China Electric Power University, Beijing 102206 (China); Key Lab of Novel Thin Film Solar Cells, Institute of Plasma Physics, Chinese Academy of Sciences, P.O. Box 1126, 230031 Hefei (China)], E-mail: xkwang@ipp.ac.cn

    2009-09-15

    Bentonite has been widely studied in nuclear waste management because of its special physicochemical properties. In this work, the sorption of Ni(II) from aqueous solution onto GMZ bentonite as a function of contact time, pH, ionic strength, foreign ions, humic acid (HA) and temperature was investigated under ambient conditions. The results indicated that the pseudo-second-order rate equation simulated the kinetic sorption process well. The sorption of Ni(II) on GMZ bentonite was strongly dependent on pH and on ionic strength. At low pH, the sorption of Ni(II) was dominated by outer-sphere surface complexation and ion exchange with Na{sup +}/H{sup +} on GMZ bentonite surfaces, whereas inner-sphere surface complexation was the main sorption mechanism at high pH. A positive effect of HA on Ni(II) sorption was found at pH<8, whereas a negative effect was observed at pH>8. The Langmuir, Freundlich, and D-R models were used to simulate the sorption isotherms of Ni(II) at three different temperatures: 303.15, 318.15 and 333.15 K. The thermodynamic parameters ({delta}H{sup 0}, {delta}S{sup 0} and {delta}G{sup 0}) of Ni(II) sorption on GMZ bentonite at the three different temperatures were calculated from the temperature-dependent sorption isotherms. The results indicated that the sorption process of Ni(II) on GMZ bentonite was endothermic and spontaneous. Experimental results indicate that GMZ bentonite is a suitable sorbent for pre-concentration and solidification of Ni(II) from large volume solutions.

  1. Ion aggregation in high salt solutions. VI. Spectral graph analysis of chaotropic ion aggregates

    Science.gov (United States)

    Choi, Jun-Ho; Cho, Minhaeng

    2016-11-01

    Carrying out molecular dynamics simulations and graph theoretical analyses of high salt solutions, and comparing numerically calculated vibrational spectroscopic properties of water with femtosecond IR pump-probe experimental data, we have recently found that ions in high salt solutions can form two morphologically different ion aggregate structures. In the cases of NaCl solutions, Na+ and Cl- tend to form compact cluster-like ion aggregate in high NaCl solutions. In contrast, K+ and SCN- form spatially extended network-like ion aggregates that also exhibit a percolating network behavior. Interestingly, a variety of graph theoretical properties of ion network in high KSCN solutions were found to be very similar to those of water H-bonding network. It was shown that spatially extended ion networks in high KSCN solutions are completely intertwined with water H-bonding networks, which might be the key to understand the high solubility of thiocyanate salts in water. Here, we further consider two salts that have been extensively studied experimentally by using femtosecond IR pump-probe technique, which are NaClO4 and NaBF4. Note that ClO4 - and BF4 - are well-known chaotropic ions that have been believed to behave as water structure breaker. To understand how such chaotropic ions affect water H-bonding structure, we carried out spectral graph analyses of molecular dynamics simulation data of these aqueous solutions. Graph spectra and degree distribution of ion aggregates formed in high NaBF4 and NaClO4 solutions show that these chaotropic anions also have a strong propensity to form ion networks. The fact that salts containing chaotropic ions like SCN-, BF4 - , and ClO4 - have very high solubility limits in water could then be related to our observation that these chaotropic anions with counter cations in high salt solutions are capable of forming intricate ion networks intertwined with water H-bonding networks. We anticipate that the present graph theoretical analysis

  2. Removal of chromium (VI) ions from aqueous solution by adsorption onto two marine isolates of Yarrowia lipolytica

    Energy Technology Data Exchange (ETDEWEB)

    Bankar, Ashok V.; Kumar, Ameeta R. [Institute of Bioinformatics and Biotechnology, University of Pune, Pune 411 007 (India); Zinjarde, Smita S., E-mail: smita@unipune.ernet.in [Institute of Bioinformatics and Biotechnology, University of Pune, Pune 411 007 (India)

    2009-10-15

    The removal of chromium (VI) ions from aqueous solutions by the biomass of two marine strains of Yarrowia lipolytica (NCIM 3589 and 3590) was studied with respect to pH, temperature, biomass, sea salt concentration, agitation speed, contact time and initial concentration of chromium (VI) ions. Maximum biosorption was observed at pH 1.0 and at a temperature of 35 deg. C. Increase in biomass and sea salts resulted in a decreased metal uptake. With an agitation speed of 130 rpm, equilibrium was attained within 2 h. Under optimum conditions, biosorption was enhanced with increasing concentrations of Cr (VI) ions. NCIM 3589 and 3590 displayed a specific uptake of Cr (VI) ions of 63.73 {+-} 1.3 mg g{sup -1} at a concentration of 950 ppm and 46.09 {+-} 0.23 mg g{sup -1} at 955 ppm, respectively. Scatchard plot analysis revealed a straight line allowing the data to be fitted in the Langmuir model. The adsorption data obtained also fitted well to the Freundlich isotherm. The surface sequestration of Cr (VI) by Y. lipolytica was investigated with a scanning electron microscope equipped with an energy dispersive spectrometer (SEM-EDS) as well as with ED-X-ray fluorescence (ED-XRF). Fourier transform infrared (FTIR) spectroscopy revealed the involvement of carboxyl, hydroxyl and amide groups on the cell surfaces in chromium binding.

  3. Functionalized macroporous copolymer of glycidyl methacrylate: The type of ligand and porosity parameters influence on Cu(II ion sorption from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Sandić Zvjezdana P.

    2009-01-01

    Full Text Available The removal of heavy metals from hydro-metallurgical and other industries' wastewaters, their safe storage and possible recovery from waste- water streams is one of the greater ecological problems of modern society. Conventional methods, like precipitation, adsorption and biosorption, electrowinning, membrane separation, solvent extraction and ion exchange are often ineffective, expensive and can generate secondary pollution. On the other hand, chelating polymers, consisting of crosslinked copolymers as a solid support and functional group (ligand, are capable of selectively loading different metal ions from aqueous solutions. In the relatively simple process, the chelating copolymer is contacted with the contaminated solution, loaded with metal ions, and stripped with the appropriate eluent. Important properties of chelating polymers are high capacity, high selectivity and fast kinetics combined with mechanical stability and chemical inertness. Macroporous hydrophilic copolymers of glycidyl methacrylate and ethylene glycol dimethacrylate modified by different amines show outstanding efficiency and selectivity for the sorption of precious and heavy metals from aqueous solutions. In this study poly(GMA-co-EGDMA copolymers were synthesized with different porosity parameters and functionalized in reactions with ethylene diamine (EDA, diethylene triamine (DETA and triethylene tetramine (TETA. Under non-competitive conditions, in batch experiments at room temperature, the rate of sorption of Cu(II ions from aqueous solutions and the influence of pH on it was determined for four samples of amino-functionalized poly(GMA-co-EGDMA. The sorption of Cu(II for both amino-functionalized samples was found to be very rapid. The sorption half time, t1/2, defined as the time required to reach 50% of the total sorption capacity, was between 1 and 2 min. The maximum sorption capacity for copper (2.80 mmol/g was obtained on SGE-10/12-deta sample. The sorption

  4. Bio sorption of copper ions with biomass of algae and dehydrated waste of olives; Biosorcion de iones cobre con biomasa de algas y orujos deshidratados

    Energy Technology Data Exchange (ETDEWEB)

    Tapia, P.; Santander, M.; Pavez, O.; Valderrama, L.; Guzman, D.; Romero, L.

    2011-07-01

    They were carried out experiments of biosorption batch and in continuous to remove copper from aqueous solutions using as adsorbents green algae and olive residues under virgins conditions and chemically activated. The results of batch bio sorption indicate that the algae present mayor elimination capacities than the waste of olives, with uptakes of copper of the order of 96 % using activated algae with dissolution of Na{sub 2}SO{sub 4} under the optimum conditions. The results of the columns tests show that the virgin algae permits the removal of more copper ions than the activate algae, with removal efficiency of 98 % during the firth 20 min, a breakthrough time of 240 min and a saturation at time of 600 min. In the second cycle the regenerated biomass showed a best performance indicating that they can be used for another bio sorption cycle. (Author) 42 refs.

  5. Removal of Cr(VI ions from waste water by electrocoagulation using iron electrode

    Directory of Open Access Journals (Sweden)

    Yehia A. El-Taweel

    2015-06-01

    Full Text Available The performance of electrocoagulation using iron electrodes for the treatment of aqueous solutions containing chromium hexavalent ions using fixed bed electrochemical batch reactor was studied. A new anode design consisting of hex nuts was connected together with a thin rode of iron. The helical shape in the nuts increases the anode surface area allowing high chromium removal rate within very short coagulation time. The effect of different parameters affecting the electrocoagulation process, such as initial hexavalent chromium concentration, applied current, electrolyte type [sodium chloride and sodium sulfate] concentration and initial pH of the solution was investigated. The optimum conditions for the EC process by using the present cell based on minimum initial hexavalent chromium concentration, energy consumption and operating cost were 100 mg of Cr(VI/l, 0.55 A, 1.5 g of sodium chloride/land pH of 1.

  6. Fluoride ions sorption of the water using natural and modified hematite with aluminium hydroxide; Sorcion de iones fluoruro del agua utilizando hematita natural y hematita acondicionada con hidroxido de aluminio

    Energy Technology Data Exchange (ETDEWEB)

    Teutli S, E. A.

    2011-07-01

    Fluorine is a mineral known for its dental benefits, but fluoride ions can cause fluoro sis in excessive quantities. There are many epidemiological studies on possible adverse effects resulting from prolonged ingestion of fluoride through drinking water. These studies demonstrate that fluoride mainly affects the bone tissue (bones and teeth), may produce an adverse effect on tooth enamel and can cause mild dental fluoro sis at concentrations from 0.9 to 1.2 mg/L in drinking water. In several states of Mexico, water contaminated with fluoride ions can be found, such as Aguascalientes, Chihuahua, Coahuila, Durango, Guanajuato, Sonora, Zacatecas, San Luis Potosi and Jalisco, where the fluoride ions levels are higher than 1.5 mg/L, established by the Mexican Official Standard (NOM-127-Ssa-2000) which sets the permissible limits of water for human use and consumption. Currently, several technologies have been proposed to remove fluoride ions from water such as precipitation methods which are based on the addition of chemicals to water and sorption methods to removed fluoride ions by sorption or ion exchange reactions by some suitable substrate capable of regenerate and reuse. In this work, the sorption of fluoride ions using unmodified and modified hematite with aluminum hydroxide to remove fluoride ions from water by bath experiments was studied. The hematite was modified by treating it with aluminum hydroxide, NaOH and Al{sub 2}(SO{sub 4}){sub 3} solutions. The characterization of hematite before and after modification with aluminum hydroxide was studied by X-ray diffraction, scanning electron microscopy, EDS and Bet. The effect of ph, contact time, concentration of fluoride ions, and the dose of sorbent on the sorption of fluoride ions by the modified hematite were studied. Equilibrium was reached within 48 hours of contact time and the maximum sorption of fluoride ions were in the range pH{sub eq} between 2.3 and 6.2. Sorption capacities of fluoride ions as a

  7. Equilibrium Sorption studies of Fe, Cu and Co ions in aqueous ...

    African Journals Online (AJOL)

    Recinius Communis Linn a commonly found herbal plant was used to prepare activated carbon by physicochemical activation method. The sorption capacity of this bio-resource material to remove Fe(III), Cu(II) and Co(II) from aqueous solutions was determined by batch tests. The influences of important parameters such as ...

  8. Effect of pH, ionic strength, foreign ions, humic acid and temperature on Zn(II) sorption onto γ-Al{sub 2}O{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Jiang; Zhang, Wei; Liu, Xia; Chen, Yuantao [Qinghai Normal University, Qinghai (China); Zhao, Lanping [Education Training Center of Ningxia Electric Power Company, Ningxia (China)

    2014-02-15

    The sorption of Zn(II) on γ-alumina was investigated as a function of contact time, pH, ionic strength, foreign ions, solid amount, humic acid (HA) and temperature by using batch technique. The results indicated that the sorption of Zn(II) onto γ-alumina was strongly dependent on pH and ionic strength. The sorption of Zn(II) increased slowly with increasing pH at pH 2-5, then increased sharply with pH increasing from 5 to 8.5, and at last maintained a maximum value at pH>8.5. A positive effect of HA on Zn(II) sorption was found at pH<7, whereas a negative effect was observed at pH>7. The thermodynamic data (ΔG{sup 0}, ΔS{sup 0}, ΔH{sup 0}) were calculated from the temperature-dependent sorption isotherms, and the results suggested that the sorption of Zn(II) on γ-alumina was endothermic and spontaneous. The sorption results revealed that the γ-alumina can be as a cost-effective sorbent for pre-concentration of Zn(II) from large volumes of aqueous solutions in environmental pollution cleanup.

  9. BIOSORPSI ION LOGAM Cr(VI) DENGAN MENGGUNAKAN BIOMASSA LAMUN Enhalus acoroides YANG TERDAPAT DI PULAU BARRANG LOMPO

    OpenAIRE

    La Nafie, N; Taba, P; Mahmud, D

    2009-01-01

    J Akta Kimia Ind 2(2) 2009 Biosorption is an alternative technique which can be used in solving environmental pollution coming from waste containing heavy metals. Biosorption of Cr(VI) ion using biomass of seagrass, Thalassia hemprichii at various contact time, pH and concentration has been investigated. Biosorption was performed by a batch method and concentration of ions before and after biosorption were measured by atomic absorption spectrophotometer (AAS). The equilibriu...

  10. Redox polymer as an adsorbent for the removal of chromium (VI and lead (II from the tannery effluents

    Directory of Open Access Journals (Sweden)

    V. Vetriselvi

    2015-06-01

    Full Text Available Polymer-based hybrid was widely fabricated and applied in heavy metal removal and other inorganic pollutants. The present study deals with the sorption efficiency of metal adsorption through the chemically modified PAA with dihydroxybenzenes into the polymeric matrix present in the tannery effluents and a parallel investigation of chromium (VI ions in aqueous solution was carried out. From the Langmuir model the removal of chromium (VI has the maximum adsorption capacity with 181.4 mg g−1. Batch sorption to remove chromium (VI and lead (II from the tannery effluents was investigated by using different parameters. The sorption efficiency was found to be 75% and 99% for chromium (VI and lead (II, respectively, present in the tannery effluents. The chemical and structural characteristics of the adsorbents were determined by UV, FT-IR, TGA, DSC, XRD and SEM-EDS analyses.

  11. Hexavalent chromium [Cr(VI)] removal by the electrochemical ion-exchange process.

    Science.gov (United States)

    Dharnaik, Amit Shivputra; Ghosh, Pranab Kumar

    2014-01-01

    In the present investigation, the performance of a laboratory-scale plate and frame-type electrochemical ion-exchange (EIX) cell on removal ofhexavalent chromium from synthetic wastewater containing 5 mg/l of Cr(VI) was evaluated under varying applied voltages. Ruthenium dioxide-coated titanium plate (RuO2/Ti) was used as anode and stainless steel plates as cathode. The EIX cell was run at different hydraulic retention time (HRT). Before using in the electrochemical cell, the capacity of ion-exchange resin was evaluated through kinetic and isotherm equilibrium tests in batch mode. The batch kinetic study result showed that the equilibrium time for effective ion exchange with resin is 2 h. The isotherm equilibrium data fit well to both Freundlich and Langmuir isotherms. Maximum capacity (qm) of resin calculated from Langmuir isotherm was 71.42 mg/g. Up to 99% of chromium removal was noticed in the EIX cell containing fresh resin at applied voltages of 10 V and higher. Migration of chromium ion to anode chamber was not noticed while performing the experiment with fresh resin. As high as 50% removal of chromium was observed from the middle chamber containing exhausted resin at an applied voltage of 25 V when the influent flow rate was maintained at 45 min of HRT. The performance of the reactor was increased to 72% when the influent flow rate was decreased to maintain at 90 min of HRT. Build-up of chromium in the anode chamber took place when exhausted resin was used in the process.

  12. Mechanism of Cu(II), Cd(II) and Pb(II) ions sorption from aqueous solutions by macroporous poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate)

    Energy Technology Data Exchange (ETDEWEB)

    Nastasović, Aleksandra B., E-mail: anastaso@chem.bg.ac.rs [University of Belgrade, Institute of Chemistry Technology and Metallurgy, Department of Chemistry, Department of Microelectronic Technologies, Njegoševa 12, Belgrade (Serbia); Ekmeščić, Bojana M. [University of Belgrade, Institute of Chemistry Technology and Metallurgy, Department of Chemistry, Department of Microelectronic Technologies, Njegoševa 12, Belgrade (Serbia); and others

    2016-11-01

    Highlights: • Macroporous PGME-deta sorption potential for Pb(II), Cd(II) and Cu(II) was studied. • Sorption kinetics obeyed pseudo-second order model. • Maximal Pb(II), Cd(II) and Cu(II) sorption capacities were 164, 152 and 120 mg g{sup −1}. • AFM indicates that metal sorption changes the size and morphology of PGME-deta. • XPS suggests complexation through the formation of Me−O and Me−N bonds in PGME-deta. - Abstract: The mechanism of Cu(II), Cd(II) and Pb(II) ions sorption from aqueous solutions by macroporous poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate) (PGME) functionalized by reaction of the pendant epoxy groups with diethylene triamine (PGME-deta) was studied using X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) analysis. Atomic force microscopy (AFM) and scanning energy-dispersive X-ray spectroscopy (SEM-EDX) were used for the determination of surface morphology of the copolymer particles. The sorption behavior of heavy metals Cu(II), Cd(II) and Pb(II) ions sorption was investigated in batch static experiments under non-competitive conditions at room temperature (298 K). The obtained results were fitted to pseudo-first order, pseudo-second order and intraparticle diffusion kinetic model. The kinetics studies showed that Cu(II), Cd(II) and Pb(II) sorption obeys the pseudo-second-order model under all investigated operating conditions with evident influence of pore diffusion.

  13. Photoluminescence Property of 1-(2-Hydroxyphenyl)thiourea and its Quenching by Chromium(VI) Ions

    Science.gov (United States)

    Sunil, A.; Jagadeeswara Rao, S.

    2015-02-01

    1-(2-Hydroxyphenyl)thiourea is a fluorogenic compound and it undergoes a very slow autooxidation to form an yellow coloured disulphide, 1-hydroxy-2-[({[N-(2- hydroxyphenyl) carbamimidoyl]disulfanyl} carbonoimidoyl) amino] benzene. In the presence of chromium(VI) ions, the rate of formation of the disulphide increases which results in the quenching of fluorescence. This analytical property has been utilized for chromium(VI) determination. The emission studies were recorded at λEx=416nm and λEm=520nm respectively. The influence of analytical properties, role of surfactants and activators are reported. Fluorescence quenching studies have been experimentally verified using Stern-Volmer plots.

  14. Batch sorption dynamics, kinetics and equilibrium studies of Cr(VI), Ni(II) and Cu(II) from aqueous phase using agricultural residues

    Science.gov (United States)

    Kaur, Rajvinder; Singh, Joginder; Khare, Rajshree; Cameotra, Swaranjit Singh; Ali, Amjad

    2013-03-01

    In the present study, the agricultural residues viz., Syzygium cumini and Populus deltoides leaves powder have been used for the biosorption of Cu(II), Ni(II), and Cr(VI) from aqueous solutions. FTIR and SEM analysis of the biosorbents were performed to explore the type of functional groups available for metal binding and to study the surface morphology. Various physico-chemical parameters such as pH, adsorbent dosage, initial metal ion concentration, and equilibrium contact time were studied. Thermodynamic studies were carried out and the results demonstrated the spontaneous and endothermic nature of the biosorption process. The equilibrium data were tested using four isotherm models—Langmuir, Freundlich, Temkin and Dubinin-Radushkevich and the maximum biosorption capacities were evaluated. The Pseudo-first-order, pseudo-second-order, Elovich and intraparticle diffusion models were applied to study the reaction kinetics with pseudo-second order model giving the best fit ( R 2 = 0.99) to the experimental data.

  15. Cotton fiber/ZrO{sub 2}, a new material for adsorption of Cr(VI) ions in water

    Energy Technology Data Exchange (ETDEWEB)

    Muxel, Alfredo Alberto; Nobre Gimenez, Sonia Maria; Souza Almeida, Flaveli Aparecida de; Silva Alfaya, Reni Ventura da; Silva Alfaya, Antonio Alberto da [Departamento de Quimica, Universidade Estadual de Londrina-UEL, Londrina, PR (Brazil)

    2011-03-15

    The natural cotton fiber was used to synthesize an anion exchange, containing ZrO{sub 2} film on its surface, NCFZC (natural cotton fiber/ZrO{sub 2} composite). This anion exchanger was produced by the reaction of the zirconium oxychloride and hydroxyl groups on surface of the natural cotton fiber. The material was used for Cr(VI) ions adsorption studies. Adsorption equilibrium time and optimum pH for Cr(VI) adsorption were found to be 6 h and 4.0, respectively. The Langmuir and Temkin isotherms were used to models adsorption equilibrium data. The adsorption capacity of NCFZC was found to be 1.33 mmol/g. Kinetic studies showed that the rate of adsorption of Cr(VI) on NCFZC obeyed a pseudo-second-order kinetic model. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  16. Chemical speciation of uranium(VI) in marine environments: complexation of calcium and magnesium ions with [(UO{sub 2})(CO{sub 3}){sub 3}]{sup 4-} and the effect on the extraction of uranium from seawater

    Energy Technology Data Exchange (ETDEWEB)

    Endrizzi, Francesco; Rao, Linfeng [Chemical Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, CA (United States)

    2014-10-27

    The interactions of Ca{sup 2+} and Mg{sup 2+} with [UO{sub 2}(CO{sub 3}){sub 3}]{sup 4-} were studied by calcium ion selective electrode potentiometry and spectrophotometry. The stability constants of ternary Ca-UO{sub 2}-CO{sub 3} and Mg-UO{sub 2}-CO{sub 3} complexes were determined with calcium ion selective electrode potentiometry and optical absorption spectrophotometry, respectively. The enthalpies of complexation for two successive complexes, [CaUO{sub 2}(CO{sub 3}){sub 3}]{sup 2-} and [Ca{sub 2}UO{sub 2}(CO{sub 3}){sub 3}](aq), were determined for the first time by microcalorimetry. The data help to revise the speciation of uranium(VI) species under seawater conditions. In contrast to the previously accepted assumption that the highly negatively charged [UO{sub 2}(CO{sub 3}){sub 3}]{sup 4-} is the dominant species, the revised speciation indicates that the dominant aqueous uranium(VI) species under seawater conditions is the neutral [Ca{sub 2}UO{sub 2}(CO{sub 3}){sub 3}](aq). The results have a significant impact on the strategies for developing efficient sorption processes to extract uranium from seawater. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  17. Actinides sorption onto hematite. Experimental data, surface complexation modeling and linear free energy relationship

    Energy Technology Data Exchange (ETDEWEB)

    Romanchuk, Anna Y.; Kalmykov, Stephan N. [Lomonosov Moscow State Univ., Moscow (Russian Federation). Dept. of Chemistry

    2014-07-01

    The sorption of actinides in different valence states - Am(III), Th(IV), Np(V) and U(VI) onto hematite have been revisited with the special emphasis on the equilibrium constants of formation of surface species. The experimental sorption data have been treated using surface complexation modeling from which the set of new values of equilibrium constants were obtained. Formation of inner sphere monodentate surface species adequately describes the pH-sorption edges for actinide ions indicative the ionic electrostatic nature of bonding with small or no covalency contribution. The linear free energy relationship representing the correlation between the hydrolysis constants and surface complexation constants has been developed for various cations including K(I), Li(I), Na(I), Ag(I), Tl(I), Sr(II), Cu(II), Co(II), La(III), Eu(III), Ga(III), Am(III), Th(IV), Np(V), U(VI). (orig.)

  18. Redox polymer as an adsorbent for the removal of chromium (VI) and lead (II) from the tannery effluents

    OpenAIRE

    V. Vetriselvi; Jaya Santhi, R.

    2015-01-01

    Polymer-based hybrid was widely fabricated and applied in heavy metal removal and other inorganic pollutants. The present study deals with the sorption efficiency of metal adsorption through the chemically modified PAA with dihydroxybenzenes into the polymeric matrix present in the tannery effluents and a parallel investigation of chromium (VI) ions in aqueous solution was carried out. From the Langmuir model the removal of chromium (VI) has the maximum adsorption capacity with 181.4 mg g−1. ...

  19. Influence of pH, layer charge location and crystal thickness distribution on U(VI) sorption onto heterogeneous dioctahedral smectite

    Energy Technology Data Exchange (ETDEWEB)

    Guimarães, Vanessa [Instituto de Ciências da Terra – Porto, DGAOT, Faculdade de Ciências, Universidade do Porto, Rua do Campo Alegre 687, 4169-007 Porto (Portugal); Geobiotec. Departamento de Geociências da Universidade de Aveiro, Campo Universitário de Santiago, 3810-193 Aveiro (Portugal); Rodríguez-Castellón, Enrique; Algarra, Manuel [Departamento de Química Inorgánica, Facultad de Ciencias, Universidad de Málaga. Campus de Teatino s/n, 29071 Málaga (Spain); Rocha, Fernando [Geobiotec. Departamento de Geociências da Universidade de Aveiro, Campo Universitário de Santiago, 3810-193 Aveiro (Portugal); Bobos, Iuliu, E-mail: ibobos@fc.up.pt [Instituto de Ciências da Terra – Porto, DGAOT, Faculdade de Ciências, Universidade do Porto, Rua do Campo Alegre 687, 4169-007 Porto (Portugal)

    2016-11-05

    Highlights: • The UO{sub 2}{sup 2+} sorption at pH 4 and 6 on heterogeneous smectite structure. • The cation exchange process is affected by layer charge distribution. • Surface complexation and cation exchange modelling. • New binding energy components identified by X-ray photoelectron spectroscopy. - Abstract: The UO{sub 2}{sup 2+} adsorption on smectite (samples BA1, PS2 and PS3) with a heterogeneous structure was investigated at pH 4 (I = 0.02 M) and pH 6 (I = 0.2 M) in batch experiments, with the aim to evaluate the influence of pH, layer charge location and crystal thickness distribution. Mean crystal thickness distribution of smectite crystallite used in sorption experiments range from 4.8 nm (sample PS2), to 5.1 nm (sample PS3) and, to 7.4 nm (sample BA1). Smaller crystallites have higher total surface area and sorption capacity. Octahedral charge location favor higher sorption capacity. The sorption isotherms of Freundlich, Langmuir and SIPS were used to model the sorption experiments. The surface complexation and cation exchange reactions were modeled using PHREEQC-code to describe the UO{sub 2}{sup 2+} sorption on smectite. The amount of UO{sub 2}{sup 2+} adsorbed on smectite samples decreased significantly at pH 6 and higher ionic strength, where the sorption mechanism was restricted to the edge sites of smectite. Two binding energy components at 380.8 ± 0.3 and 382.2 ± 0.3 eV, assigned to hydrated UO{sub 2}{sup 2+} adsorbed by cation exchange and by inner-sphere complexation on the external sites at pH 4, were identified after the U4f{sub 7/2} peak deconvolution by X-photoelectron spectroscopy. Also, two new binding energy components at 380.3 ± 0.3 and 381.8 ± 0.3 eV assigned to ≡AlOUO{sub 2}{sup +} and ≡SiOUO{sub 2}{sup +} surface species were observed at pH 6.

  20. Kinetic and equilibrium study for the sorption of Pb(II) ions from ...

    African Journals Online (AJOL)

    This paper reports the kinetic and equilibrium studies of Eichhornia crassipes root biomass as a biosorbent for Pb(II) ions from aqueous system. Batch adsorption studies were carried out to examine the influence of various parameters such as the pH, contact time, adsorbent dose, initial metal ion concentration, temperature ...

  1. Removal of Cr(VI) ions by sewage sludge compost biomass from aqueous solutions: Reduction to Cr(III) and biosorption

    Science.gov (United States)

    Chen, Huixia; Dou, Junfeng; Xu, Hongbin

    2017-12-01

    Sewage sludge compost biomass was used as a novel biosorbent to remove hexavalent chromium from water. Surface area analysis, scanning electron microscopy, fourier-transform infrared spectroscopy, energy-dispersive X-ray spectroscopy, and point zero charge was applied to study the microstructure, compositions and chemical bonding states of the biomass adsorbent. Effects of contact time, biomass dosage, agitation speed, pH, the initial concentration of Cr(VI) and Cr(Ⅲ) on its adsorption removal were also performed in the batch experiments. A model describing adsorption, desorption and reduction phenomena during the sorption process has been referenced to model Cr(VI) sorption onto sewage sludge compost biomass. The result of characterization test shows that adsorption of Cr(VI) onto sewage sludge compost biomass followed by the partial reduction to Cr(Ⅲ) by biomass groups such as hydroxyl, carboxyl, and amino groups. The absorption kinetics model in the description of adsorption-coupled reduction of Cr(VI) fits successfully the kinetic data obtained at different temperatures and describes the kinetics profile of total, hexavalent and trivalent chromium. The study shows that sewage sludge compost biomass could be used as a potential biosorbent for removal of hexavalent chromium from wastewaters.

  2. Chromium (VI) ion adsorption features of chitosan film and its chitosan/zeolite conjugate 13X film.

    Science.gov (United States)

    Batista, Anabelle C L; Villanueva, Emílio R; Amorim, Rosa Valéria S; Tavares, Maria Teresa; Campos-Takaki, Galba M

    2011-04-28

    This research evaluated the importance of the adsorption properties of chitosan a chitosan/zeolite conjugate film for the removal of Cr(VI) ions from solutions in the 5-260 mg/L concentration range, when the pH was adjusted to 4.0 and 6.0. The uptake capacities of the films formed by chitosan and by the chitosan/zeolite conjugate were calculated by mass balance. The equilibrium isotherms were fitted to the Langmuir, Freundlich and Redlich-Peterson models. The chitosan film seems to be a good sorbent for Cr(VI) at pH 4, but its physical instability suggests the need for a more resilient support. Due to this fact zeolite was added to the chitosan matrix in solution and a chitosan/zeolite (CS/Zeo) film was thus formed. The solubility of the film and the characterization of the different matrices by FTIR, TGA and X-Ray showed that a cross-linked structure was formed between the chitosan and zeolite and the solubility of the film increased. In this study, the low manufacturing cost of the CS/Zeo matrix, the good uptake of Cr(VI) at acidic pH (17.28 mg/g) and the non desorption of Cr(VI) from the film in water suggests this combination should be tested in industrial environment.

  3. Mechanism of Cu(II), Cd(II) and Pb(II) ions sorption from aqueous solutions by macroporous poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate)

    Science.gov (United States)

    Nastasović, Aleksandra B.; Ekmeščić, Bojana M.; Sandić, Zvjezdana P.; Ranđelović, Danijela V.; Mozetič, Miran; Vesel, Alenka; Onjia, Antonije E.

    2016-11-01

    The mechanism of Cu(II), Cd(II) and Pb(II) ions sorption from aqueous solutions by macroporous poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate) (PGME) functionalized by reaction of the pendant epoxy groups with diethylene triamine (PGME-deta) was studied using X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) analysis. Atomic force microscopy (AFM) and scanning energy-dispersive X-ray spectroscopy (SEM-EDX) were used for the determination of surface morphology of the copolymer particles. The sorption behavior of heavy metals Cu(II), Cd(II) and Pb(II) ions sorption was investigated in batch static experiments under non-competitive conditions at room temperature (298 K). The obtained results were fitted to pseudo-first order, pseudo-second order and intraparticle diffusion kinetic model. The kinetics studies showed that Cu(II), Cd(II) and Pb(II) sorption obeys the pseudo-second-order model under all investigated operating conditions with evident influence of pore diffusion.

  4. Study of polyethyleneimine- and amidoxime-functionalized hybrid biomass of Spirulina (Arthrospira) platensis for adsorption of uranium (VI) ion.

    Science.gov (United States)

    Bayramoglu, Gulay; Akbulut, Aydin; Arica, M Yakup

    2015-11-01

    This study investigates the potential application of the polyethyleneimine- (PEI) and amidoxime-modified Spirulina (Arthrospira) platensis biomasses for the removal of uranium ion in batch mode using the native biomass as a control system. The uranium ion adsorption was also characterized by attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectra, zeta potential analysis, and surface area measurement studies. The effects of pH, biomass amount, contact time, initial uranium ion concentration, and ionic strength were evaluated by using native and modified algal biomass preparations. The uranium ion removal was rapid, with more than 70% of total adsorption taking place in 40 min, and equilibrium was established within 60 min. From the experimental data, it was found that the amount of adsorption uranium ion on the algal preparations decreased in the following series: amidoxime-modified algal biomass > PEI-modified algal biomass > native algal biomass. Maximum adsorption capacities of amidoxime- and PEI-modified, and native algal biomasses were found to be 366.8, 279.5, and 194.6 mg/g, respectively, in batchwise studies. The adsorption rate of U(VI) ion by amidoxime-modified algal biomass was higher than those of the native and PEI-modified counterparts. The adsorption processes on all the algal biomass preparations followed by the Dubinin-Radushkevitch (D-R) and Temkin isotherms and pseudo-second-order kinetic models. The thermodynamic parameters were determined at four different temperatures (i.e., 15, 25, 35, and 45 °C) using the thermodynamics constant of the Temkin isotherm model. The ΔH° and ΔG° values of U(VI) ion adsorption on algal preparations show endothermic heat of adsorption; higher temperatures favor the process. The native and modified algal biomass preparations were regenerated using 10 mM HNO3. These results show that amidoxime-modified algal biomass can be a potential candidate for effective removal of U(VI) ion from

  5. Cr(VI) sorption by free and immobilised chromate-reducing bacterial cells in PVA-alginate matrix: equilibrium isotherms and kinetic studies.

    Science.gov (United States)

    Rawat, Monica; Rawat, A P; Giri, Krishna; Rai, J P N

    2013-08-01

    Chromate-resistant bacterial strain isolated from the soil of tannery was studied for Cr(VI) bioaccumulation in free and immobilised cells to evaluate its applicability in chromium removal from aqueous solution. Based on the comparative analysis of the 16S rRNA gene, and phenotypic and biochemical characterization, this strain was identified as Paenibacillus xylanilyticus MR12. Mechanism of Cr adsorption was also ascertained by chemical modifications of the bacterial biomass followed by Fourier transform infrared spectroscopy analysis of the cell wall constituents. The equilibrium biosorption analysed using isotherms (Langmuir, Freundlich and Dubinin-Redushkevich) and kinetics models (pseudo-first-order, second-order and Weber-Morris) revealed that the Langmuir model best correlated to experimental data, and Weber-Morris equation well described Cr(VI) biosorption kinetics. Polyvinyl alcohol alginate immobilised cells had the highest Cr(VI) removal efficiency than that of free cells and could also be reused four times for Cr(VI) removal. Complete reduction of chromate in simulated effluent containing Cu(2+), Mg(2+), Mn(2+) and Zn(2+) by immobilised cells, demonstrated potential applications of a novel immobilised bacterial strain MR12, as a vital bioresource in Cr(VI) bioremediation technology.

  6. Sorption properties of wool

    Directory of Open Access Journals (Sweden)

    Radetić Maja M.

    2004-01-01

    Full Text Available Strict ecological legislation, especially in highly developed countries, imposed requirements for the purification of industrial effluents and the need for efficient oil clean up after sea and inland water spills. Although numerous processes have been developed, the application of sorbents is still one of the most efficient methods to remove heavy metal ions, dyes and crude oil from water. Recently, special attention was paid to sorbents based on natural fibres. A review of studies concerning the sorption properties of wool is presented in this paper. The presence of various functional groups on the wool fibre surface contributes to the efficient sorption of heavy metal ions and dyes. A hydrophobic, scaly surface and fibre crimp strongly influence the high sorption capacity of wool for oil. Wool has great sorption potential even as a recycled material. Accordingly, it can be used as a viable substitute to commercially available synthetic sorbents that show poor biodegradab ility.

  7. SORPTION OF NICKEL IONS ONTO CHEMICALLY MODIFIED PARTHENIUM HYSTEROPHOROUS L. AND THEIR QUANTITATIVE DETERMINATION BY TITRATION.

    Directory of Open Access Journals (Sweden)

    Firoz Ali ANSARI

    2017-04-01

    Full Text Available The removal efficiency of Nickel ions from aqueous solution on chemically treated Parthenium hysterophorous leaf powder (PHLP has been investigated. The adsorbent was characterized by SEM images and FTIR spectra analysis. The effect of several parameters such as pH, adsorbent dose, concentration of Ni ion solution and contact time was evaluated using batch experiments. Nickel ions removal was pH dependent and the maximum removal was found to be at pH 7. The maximum removal of Ni ions was achieved within 100 min after the start of every experiment. The equilibrium adsorption data were fitted to Langmuir, Freundlich, Temkin and Dubnin- Radushkevich (D-R adsorption isotherm models to evaluate the models parameter. Experimental results showed that the Langmuir isotherm model best describes for the adsorption of metal than Freundlich isotherm model. Adsorption data were processed according to various kinetic models. Pseudo-first order and pseudo-second order were applied to fit the kinetic results. Pseudo-first order model was less applicable than pseudo-second order. Thermodynamic studies showed spontaneous and exothermic nature in the adsorption of Ni (II onto PHLP.

  8. Sorption of Uranium Ions from Their Aqueous Solution by Resins Containing Nanomagnetite Particles

    OpenAIRE

    Abd El-Magied, Mahmoud O.

    2016-01-01

    Magnetic amine resins composed of nanomagnetite (Fe3O4) core and glycidyl methacrylate (GMA)/N,N′-methylenebisacrylamide (MBA) shell were prepared by suspension polymerization of glycidyl methacrylate with N,N′-methylenebisacrylamide in the presence of nanomagnetite particles and immobilized with different amine ligands. These resins showed good magnetic properties and could be easily retrieved from their suspensions using an external magnetic field. Adsorption behaviors of uranium ions on th...

  9. Study of the temperature influence during the uranium (Vi) sorption on surface of ZrP{sub 2}O{sub 7} in presence of oxalic and salicylic acid; Estudio de la influencia de la temperatura durante la sorcion de uranio (VI) en la superficie del ZrP{sub 2}O{sub 7} en presencia de acidos oxalico y salicilico

    Energy Technology Data Exchange (ETDEWEB)

    Garcia G, N.

    2013-07-01

    This work studies the effect of temperature on the uranium (Vi) sorption onto zirconium diphosphate in the presence of organic acids (oxalic and salicylic acids). Zirconium diphosphate was synthesized by a chemical condensation reaction and characterized using several analytical techniques, in order to check its purity. This point is very important because the presence of any impurities or secondary phases may interfere with the hydration and sorption process. Prior to the sorption experiments, three batches of zirconium diphosphate were pre-equilibrated with NaClO{sub 4}, oxalic acid or salicylic acid solutions. The hydrated solids were washed and dried and then again characterized in order to study the interactions between organic acids and zirconium diphosphate surface. Uranium sorption onto zirconium diphosphate (pre-equilibrated with NaClO{sub 4}, oxalic acid and salicylic acid solutions) was investigated as a function of ph, organic acid and temperature (20, 40 y 60 grades C). Thermodynamic parameters for the sorption reactions (enthalpy change, entropy change and Gibbs free energy change) were determined from temperature dependence of distribution coefficient by using the Vant Hoff equation. Solids characterization after hydration shows that exist an interaction between organic acids and ZrP{sub 2}O{sub 7}. This fact was confirmed with the microcalorimetry study, the reaction heat for hydration of zirconium diphosphate in NaClO{sub 4} solution was exothermic (-269.59 mJ) and for hydration of zirconium diphosphate in oxalic acid solution was endothermic (53.64 mJ). The experimental results showed important differences in the sorption mechanisms for the reaction of Uranium with ZrP{sub 2}O{sub 7} in the presence and absence of organic acids. For the zirconium diphosphate hydrated with oxalic acid, the sorption percentage was 50% from lowest ph values. For the zirconium diphosphate hydrated with salicylic acid, the initial concentration of uranium was 6 x 10

  10. Adsorption of U(VI) ions from aqueous solutions by activated carbon prepared from Antep pistachio (Pistacia vera L.) shells

    Energy Technology Data Exchange (ETDEWEB)

    Donat, Ramazan [Pamukkale Univ., Denizli (Turkey). Dept. of Chemistry; Erden, Kadriye Esen [Pamukkale Univ., Kinikli-Denizli (Turkey). Denizli Vocational School of Technical Sciences

    2017-08-01

    Antep pistachio (Pistacia vera L.) shells an abundant and low cost natural resource in Turkey was used to prepare activated carbon by physiochemical activation and carbon dioxide (CO{sub 2}) atmosphere as the activating agents at 700 C for 2 h. The adsorption equilibrium of U(VI) from aqueous solutions on such carbon has been studied using a batch system. The parameters that affect the U(VI) adsorption, such as particle size of adsorbent, contact time, of pH of the solution, and temperature, have been investigated and conditions have also been optimized. The equilibrium data for U(VI) ions' adsorption onto activated carbon well fitted to the Langmuir equation, with a maximum monolayer adsorption capacity of 8.68 mg/g, The Freundlich and Dubinin-Radushkevich (D-R) isotherms have been applied and the data correlated well with Freundlich model and that the adsorption is physical in nature (E{sub a}=15.46 kJ/mol). Thermodynamic parameters [ΔH{sub s}=11.33 kJ/mol, ΔS=0.084 kJ/molK, ΔG (293.15 K)=-13.29 kJ/mol] showed the endothermic heat of adsorption and the feasibility of the process.

  11. Sorption studies of heavy metal ions by salicylic acid–formaldehyde–catechol terpolymeric resin: Isotherm, kinetic and thermodynamics

    Directory of Open Access Journals (Sweden)

    Riddhish R. Bhatt

    2015-05-01

    Full Text Available Terpolymeric resin has been synthesized by condensing salicylic acid with catechol employing formaldehyde as a cross linking agent at 80 ± 5 °C using DMF as a solvent. The resin was characterized by elemental analysis, FTIR, XRD and thermal analysis (TGA, DTA and DTG. The morphology of the resin was studied by optical photographs and scanning electron micrographs (SEM at different magnifications. The physico-chemical properties have been studied. The uptake behavior of various metal ions viz. Ni(II, Cu(II, Zn(II, Cd(II and Pb(II towards synthesized resin has been studied depending on contact time, pH and temperature. The selectivity order found is: Cu(II > Zn(II > Pb(II > Ni(II > Cd(II. The sorption data obtained at optimized conditions were analyzed by six two parameter isotherm models like Langmuir, Freundlich, Temkin, Dubinin–Radushkevich (D–R, Halsey and Harkins–Jura. The Langmuir, Freundlich and Dubinin–Radushkevich (D–R isotherms were found better to describe the sorption data with high correlation for the adsorption with a low SSE value for all the metals under study. The adsorption capacities of the SFC resin for removal of Ni(II, Cu(II, Zn(II, Cd(II and Pb(II were determined with the Langmuir equation and found to be 0.815, 1.104, 1.215, 0.498, and 0.931 mmol/g respectively. The adsorption process follows first order kinetics and specific rate constant Kr was obtained by the application of Lagergren equation. Thermodynamic parameters viz. ΔGads, ΔSads and ΔHads have also been calculated for the metal-resin systems. The external diffusion rate constant (Ks and intra-particle diffusion rate constant (Kid were calculated by Spahn–Schlunder and Weber–Morris models respectively. Desorption studies were done using various desorbing agents viz. de-ionized water, boiled water, various concentrations of HCl, ammonia, thiourea, citric acid and tartaric acid.

  12. Selective cloud point extraction and graphite furnace atomic absorption spectrometric determination of molybdenum (VI) ion in seawater samples

    Energy Technology Data Exchange (ETDEWEB)

    Filik, Hayati, E-mail: filik@istanbul.edu.tr [Istanbul University, Faculty of Engineering, Department of Chemistry, Avcilar, 34320 Istanbul (Turkey); Cengel, Tayfun; Apak, Resat [Istanbul University, Faculty of Engineering, Department of Chemistry, Avcilar, 34320 Istanbul (Turkey)

    2009-09-30

    A cloud point extraction process using the nonionic surfactant Triton X-114 to extract molybdenum from aqueous solutions was investigated. The method is based on the complexation reaction of Mo(VI) with 1,2,5,8-tetrahydroxyanthracene-9,10-dione (quinalizarine: QA) and micelle-mediated extraction of the complex. The enriched analyte in the surfactant-rich phase was determined by graphite furnace atomic absorption spectrometry (GFAAS). The optimal extraction and reaction conditions (e.g. pH, reagent and surfactant concentrations, temperature, incubation and centrifugation times) were evaluated and optimized. Under the optimized experimental conditions, the limit of detection (LOD) for Mo(VI) was 7.0 ng L{sup -1} with an preconcentration factor of {approx}25 when 10 mL of sample solution was preconcentrated to 0.4 mL. The proposed method (with extraction) showed linear calibration within the range 0.03-0.6 {mu}g L{sup -1}. The relative standard deviation (RSD) was found to be 3.7% (C{sub Mo(VI)} = 0.05 {mu}g L{sup -1}, n = 5) for pure standard solutions, whereas RSD for the recoveries from real samples ranged between 2 and 8% (mean RSD = 3.9%). The method was applied to the determination of Mo(VI) in seawater and tap water samples with a recovery for the spiked samples in the range of 98-103%. The interference effect of some cations and anions was also studied. In the presence of foreign ions, no significant interference was observed. In order to verify the accuracy of the method, a certified reference water sample was analysed and the results obtained were in good agreement with the certified values.

  13. Adsorption of Cu(II) and Cr(VI) ions by chitosan: Kinetics and ...

    African Journals Online (AJOL)

    drinie

    2001-01-01

    Jan 1, 2001 ... Current treatment for the removal of Cr. (VI) involves acid catalysed chemical reduction to Cr3+. The Cr3+ is then precipitated as hydroxide at alkaline conditions using either caustic or lime (Udaybhaskar et al., 1990). The presence of Cu (II) in wastewater is also a problem. Copper is used extensively by.

  14. Grafting of β-cyclodextrin to magnetic graphene oxide via ethylenediamine and application for Cr(VI) removal.

    Science.gov (United States)

    Wang, Hui; Liu, Yun-guo; Zeng, Guang-ming; Hu, Xin-jiang; Hu, Xi; Li, Ting-ting; Li, Hua-ying; Wang, Ya-qin; Jiang, Lu-hua

    2014-11-26

    A novel β-cyclodextrin (β-CD) polymer adsorbent named β-cyclodextrin/ethylenediamine/magnetic graphene oxide (CD-E-MGO) was synthesized for decontamination of Cr(VI) from aqueous solution. The sorption kinetics, isotherms and thermodynamics, as well as the effects of pH, aniline and ionic strength on the sorption process were investigated. The results indicated that CD-E-MGO could effectively remove Cr(VI) from aqueous solution and the sorption data could be well described by pseudo-second-order and Langmuir models. The intraparticle diffusion study indicated that intraparticle diffusion was not the only rate-limiting step. Thermodynamic parameters revealed that the sorption reaction was an endothermic and spontaneous process. The decontamination of Cr(VI) was influenced by solution pH and ionic strength. In the system with aniline, the Cr(VI) sorption was improved at low pH values but reduced at high pH values. These results are important for estimating and optimizing the removal of metal ions by CD-E-MGO composite. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. Hydrogen Sorption and Transport

    Science.gov (United States)

    McNeece, C. J.; Hesse, M. A.

    2015-12-01

    Hydrogen is unique among aqueous ions, both in its importance for geochemical reactions, and in its complex transport behavior through reactive media. The structure of hydrogen reaction fronts can be analyzed in the advective limit of the transport equation. At local chemical equilibrium, sorption of hydrogen onto the media surface (sorption isotherm) controls reaction front morphology. Transport modeling thus necessitates accurate knowledge of surface chemistry. Though motivated by transport, sorption models are often parameterized against batch titration experiments. The validity of these parameterizations, in a transport setting, are seldom tested. The analytic solution to the transport equation gives an algebraic relationship between concentration velocity and equilibrium sorption behavior. In this study, we conduct a suite of column flow experiments through quartz sand. Hydrogen concentration breakthrough curves at the column outlet are used to infer the "transport sorption isotherm." These results are compared to the batch titration derived sorption isotherm. We find excellent agreement between the datasets. Our findings suggest that, for aqueous hydrogen, local chemical equilibrium is a valid assumption. With the goal of a predictive transport model, we parameterize various sorption models against this dataset. Models which incorporate electrostatic effects at the surface predict transport well. Nonelectrostatic models such as the Kd, Langmuir, and Freundlich models fail. These results are particularly compelling as nonelectrostatic models are often employed to predict hydrogen transport in many reactive transport code.

  16. Uranium(VI) retention by Ca-bentonite under (hyper)alkaline conditions

    Energy Technology Data Exchange (ETDEWEB)

    Philipp, Thimo; Schmeide, Katja [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Surface Processes

    2017-06-01

    The sorption behavior of U(VI) on Ca-bentonite was studied in saline, (hyper)alkaline solution via batch experiments. At pH 8.5-9.5 sorption is low in the presence of CO{sub 2} due to the formation of weakly sorbing uranyl carbonate species, which have been observed to dominate speciation up to pH 10 by time-resolved laser-induced fluorescence spectroscopy (TRLFS). In the pH region 10-12, U(VI) retention is almost complete. The retention can either be attributed to strongly sorbing uranyl hydroxo complexes or to a partial precipitation of uranium due to an altered solubility of U(VI) induced by ions leached out of the bentonite.

  17. Effect of modulator sorption on gradient shape in ion-exchange chromatography

    Science.gov (United States)

    Velayudhan, A.; Ladisch, M. R.; Mitchell, C. A. (Principal Investigator)

    1995-01-01

    Mobile phase additives, or modulators, are used in gradient elution chromatography to facilitate separation and reduce separation time. The modulators are usually assumed to be linearly adsorbed or unadsorbed. Here, the consequences of nonlinear modulator adsorption are examined for ion-exchange gradient elution through a series of simulations. Even when the buffer salt is identical to the modulator salt, gradient deformation is observed; the extent of deformation increases as the volume of the feed is increased. When the modulator salt is different from the buffer salt, unusual effects are observed, and the chromatograms are quite different from those predicted by classical gradient elution theory. In particular, local increases in the buffer concentration are found between feed bands, and serve to improve the separation. These effects become more pronounced as the feed volume increases, and could therefore prove valuable in preparative applications.

  18. Sorption of tartrate ions to lanthanum (III)-modified calcium fluor- and hydroxyapatite.

    Science.gov (United States)

    Aissa, Abdallah; Debbabi, Mongi; Gruselle, Michel; Thouvenot, René; Flambard, Alexandrine; Gredin, Patrick; Beaunier, Patricia; Tõnsuaadu, Kaia

    2009-02-01

    The present article details the formation of lanthanum-modified apatites and the binding process of tartrate ions with these obtained apatites. Chemical analyses, FT-IR and (31)P NMR spectroscopies, XRD powder, TGA, and TEM analyses were employed for studying the reaction between Ca(10)(PO(4))(6)(OH)(2) (HAp) or Ca(10)(PO(4))(6)(F)(2) (FAp) and LaCl(3). The reaction was found to take place mainly through partial dissolution of the apatite followed by precipitation of a new phase containing lanthanum phosphate. When La(3+) was introduced in the presence of L(+)-tartaric acid (TAH(2)), no fundamental changes were observed in the HAp or FAp structures. However, there did occur a formation of a new phase of Ca or/and La tartrate salt.

  19. Sol-gel synthesis of magnetic sorbents based on porous iron oxides for the removal of U(VI) from aqueous solution

    Science.gov (United States)

    Papynov, E. K.; Portnyagin, A. S.; Cherednichenko, A. I.; Tkachenko, I. A.; Modin, E. B.; Dran'kov, A. N.; Kvach, A. A.; Zemchenko, I. V.; Tananaev, I. G.; Avramenko, V. A.

    2017-02-01

    An original synthetic route to nanostructured iron oxides with porous structure and to their reduced derivatives, prospective for uranium (VI) uptake from water media, is presented. The uniqueness of method includes combination of sol-gel technology, which used for generating inorganic framework, and template synthesis for porous structure formation with the help of poreforming agent (polymer latex). Method of consolidating porous iron oxides and its influence on such characteristics as porosity, magnetization, morphology, phase composition and sorption properties are described. Sorption properties of the materials based on iron oxides and their reduced derivatives with respect to uranium (VI) from water media of different acidity has been investigated. Mechanism of uranium (VI) sorption on the obtained materials has been determined. The interaction of the sorbents with uranyl-ions was shown to change depending on phase composition and structure of the solid matrix.

  20. A comparative study on metal sorption by brown seaweed.

    Science.gov (United States)

    Tsui, Martin T K; Cheung, K C; Tam, Nora F Y; Wong, M H

    2006-09-01

    This study compared the sorption of Ag, Cd, Co, Cd, Mn, Ni, Pb and Zn by a Ca-treated Sargassum biomass at pH 5.0, under low and high ionic strength (IS) conditions. The sorption isotherms of As [As(V)] and Cr [Cr(III) and Cr(VI)] were also determined at low IS. The isotherm data for the eight cationic metals and Cr(III) were well fitted by Langmuir equations. Generally, the maximum metal uptake (Umax) followed: Cr(III) > Pb approximately Cu > Ag approximately Zn approximately Cd > Ni approximately Mn approximately Co > Cr(VI) > As(V) at low IS and Pb > Cu > Co > Mn approximately Cd > Zn approximately Ag > Ni at high IS. As(V) did not bind to the seaweed at pH 5.0. The results indicated that sorption of Pb was not affected by the increasing IS, though the percentage of free Pb ions in the water was greatly reduced as predicted by the speciation model. High IS lowered Umax by 10-36% (except Co and Pb), and lowered the affinity constant of the metal by 33-91% for all cationic metals, as compared to low IS. Moreover, the removal efficiency of the cationic metals and Cr decreased exponentially with initial metal concentrations and was lower at high IS. Ion-exchange was the mechanism responsible for the cationic metal sorption onto the seaweed, and Na ion interfered with the cationic metal binding through electrostatic interaction. In conclusion, this study showed the differential binding capacity of the Sargassm biomass for different metals and oxidation states and the differential effects of IS. According to the present results, Sargassum may be considered a good biosorbent for cationic metals (especially Pb) in both low and high-salt containing wastewater.

  1. Nanogel and superparamagnetic nanocomposite based on sodium alginate for sorption of heavy metal ions.

    Science.gov (United States)

    Lakouraj, Moslem Mansour; Mojerlou, Fatemeh; Zare, Ehsan Nazarzadeh

    2014-06-15

    Novel sodium alginate supported tetrasodium thiacalix[4]arene tetrasulfonate (TSTC[4]AS-s-SA) nanogel was prepared using sodium alginate nanoparticles. Then, superparamagnetic nanocomposite of sodium alginate (Fe3O4@TSTC[4]AS-s-SA) was fabricated from coprecipitation of sodium alginate supported tetrasodium thiacalix[4]arene tetrasulfonate and in situ generated Fe3O4 nanoparticles. Structural, morphological, surface, thermal and magnetic properties of the nanoadsorbents were studied by Fourier transform infrared (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM), differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), and vibrating sample magnetometer (VSM), respectively. Adsorptions of Cu(II), Cd(II), Pb(II), Co(II), Ni(II) and Cr(III) ions onto nanoadsorbents were studied in aqueous condition at pH=7. The results indicated that incorporation of thiacalix[4]arene tetrasulfonate and Fe3O4 into sodium alginate nanoparticles increased the adsorption capacity of sodium alginate bioadsorbents, and led to the magnetic property. The TSTC[4]AS-s-SA nanogels consist of rod-like structure with an average diameter of 50 nm. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Determination of Hexavalent Chromium (Cr(VI Concentrations via Ion Chromatography and UV-Vis Spectrophotometry in Samples Collected from Nacogdoches Wastewater Treatment Plant, East Texas (USA

    Directory of Open Access Journals (Sweden)

    Kefa K. Onchoke

    2016-01-01

    Full Text Available The concentration of hexavalent chromium (Cr(VI, a toxic environmental pollutant and carcinogen, was determined in samples collected from Nacogdoches Wastewater Treatment Plant (NWWTP using ion chromatography and UV-visible spectrophotometry (IC, UV-Vis. On reaction with 1,5-diphenylcarbazide (DPC Cr+6 forms a 1,5-diphenylcarbazide-Cr(VI complex, which is then analyzed at 530 nm and 540 nm, respectively. Via ion chromatography Cr(VI concentrations were in the range of 0.00190±0.0020 and 0.0010±0.0006 ppm at the influent and effluent, respectively. With the use of standard addition wastewater samples were spiked with a 0.5 ppm Cr(VI standard of various amounts and subsequently analyzed with UV-Vis spectrophotometry. The spiked concentrations gave Cr(VI concentrations in the range of 0.0090±0.0060 ppm and 0.0040±0.0061 ppm at the influent and influent wastewater, respectively. The determined Cr(VI concentrations through the ion chromatography and UV-Vis spectrophotometry are below the maximum USEPA contaminant concentration of 0.1 ppm. From the analysis, the NWWTP efficiently removes Cr(VI before discharge into the environment through La Nana Creek. The removal efficiency for Cr(VI was determined to be ≥92.8% along the wastewater treatment stages from the influent (aeration stage to the effluent stages prior to discharge into the La Nana Creek.

  3. Biosorption of Cr (VI) from aqueous solution by Rhizopus nigricans.

    Science.gov (United States)

    S Bai, R; Abraham, T E

    2001-08-01

    The study was aimed to quantify the Cr sorption ability of powdered biomass of Rhizopus nigricans at the best operating conditions. The influence of solution pH, agitation, Cr (VI) concentration, biomass dosage, contact time, biomass particle size and temperature were studied. The optimum pH for biosorption of Cr (VI) was found to be 2.0. Higher adsorption percentage was noted at lower initial concentrations of Cr ions, while the adsorption capacity of the biomass increased with increasing concentration of ions. Optimum biomass dosage was observed as 0.5% (w/v). More than 75% of the ions were removed within 30 min of contact and maximum removal was obtained after 8 h. Biomass particles of smaller size (90 microm) gave maximum adsorption (99.2%) at 100 mg/l concentration. The adsorption capacity increased with increase in temperature and agitation speed and the optimum were determined as 45 degrees C at 120 rpm. Freundlich and Langmuir isotherms were used to evaluate the data and the regression constants were derived. The adsorption rate constant values (Kad) were calculated for different initial concentration of Cr ions and the sorption was found to be higher at lower concentration (100 mg/l) of metal ion.

  4. Sorption of Cu(II) Ions on Chitosan-Zeolite X Composites: Impact of Gelling and Drying Conditions.

    Science.gov (United States)

    Djelad, Amal; Morsli, Amine; Robitzer, Mike; Bengueddach, Abdelkader; di Renzo, Francesco; Quignard, Françoise

    2016-01-19

    Chitosan-zeolite Na-X composite beads with open porosity and different zeolite contents were prepared by an encapsulation method. Preparation conditions had to be optimised in order to stabilize the zeolite network during the polysaccharide gelling process. Composites and pure reference components were characterized using X-ray diffraction (XRD); scanning electron microscopy (SEM); N₂ adsorption-desorption; and thermogravimetric analysis (TG). Cu(II) sorption was investigated at pH 6. The choice of drying method used for the storage of the adsorbent severely affects the textural properties of the composite and the copper sorption effectiveness. The copper sorption capacity of chitosan hydrogel is about 190 mg·g(-1). More than 70% of this capacity is retained when the polysaccharide is stored as an aerogel after supercrititcal CO₂ drying, but nearly 90% of the capacity is lost after evaporative drying to a xerogel. Textural data and Cu(II) sorption data indicate that the properties of the zeolite-polysaccharide composites are not just the sum of the properties of the individual components. Whereas a chitosan coating impairs the accessibility of the microporosity of the zeolite; the presence of the zeolite improves the stability of the dispersion of chitosan upon supercritical drying and increases the affinity of the composites for Cu(II) cations. Chitosan-zeolite aerogels present Cu(II) sorption properties.

  5. Sorption of Cu(II Ions on Chitosan-Zeolite X Composites: Impact of Gelling and Drying Conditions

    Directory of Open Access Journals (Sweden)

    Amal Djelad

    2016-01-01

    Full Text Available Chitosan-zeolite Na-X composite beads with open porosity and different zeolite contents were prepared by an encapsulation method. Preparation conditions had to be optimised in order to stabilize the zeolite network during the polysaccharide gelling process. Composites and pure reference components were characterized using X-ray diffraction (XRD; scanning electron microscopy (SEM; N2 adsorption–desorption; and thermogravimetric analysis (TG. Cu(II sorption was investigated at pH 6. The choice of drying method used for the storage of the adsorbent severely affects the textural properties of the composite and the copper sorption effectiveness. The copper sorption capacity of chitosan hydrogel is about 190 mg·g−1. More than 70% of this capacity is retained when the polysaccharide is stored as an aerogel after supercrititcal CO2 drying, but nearly 90% of the capacity is lost after evaporative drying to a xerogel. Textural data and Cu(II sorption data indicate that the properties of the zeolite-polysaccharide composites are not just the sum of the properties of the individual components. Whereas a chitosan coating impairs the accessibility of the microporosity of the zeolite; the presence of the zeolite improves the stability of the dispersion of chitosan upon supercritical drying and increases the affinity of the composites for Cu(II cations. Chitosan-zeolite aerogels present Cu(II sorption properties.

  6. Synthesis of DNPH/SDS/Fe3O4 Nanoparticles for Removal of Cr (VI Ions From Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Soheil Sobhanardakani

    2016-06-01

    Full Text Available In this study, sodium dodecyl sulfate (SDS coated magnetite modified with 2, 4-Dinitrophenylhydrazine was used to remove Cr (VI ions from aqueous solution. The modified magnetite nanoparticles were characterized by X-ray diffraction (XRD analysis, Fourier transform infrared spectroscopy (FT-IR, scanning electron microscopy (SEM, and SEM–EDXS measurement. The synthesized nanoparticles exhibited a high surface area of 75.5 m2 g−1 and were of 20 - 35 nm in particle size. The effects of parameters, including pH, dose of adsorbent, temperature and contact time were investigated to find the optimum adsorption conditions. Adsorption data fits well with the Langmuir isotherm model with a maximum adsorption capacity (qm and a Langmuir adsorption equilibrium constant (b of 169.5 mg g-1 and 0.168 L mg-1, respectively. The adsorption kinetic agrees well with pseudo-second-order model.

  7. Influence of pH on Cr(VI) ions removal from aqueous solutions using carboxymethyl cellulose-based hydrogel as adsorbent

    Science.gov (United States)

    Anah, L.; Astrini, N.

    2017-03-01

    The major problem in heavy metal pollution is that these metals are not biodegradable and accordingly accumulate in the bodies of living organisms, causing dangerous diseases and serious cell disorder. According to World Health Organization (WHO), the long term exposure of Cr(VI) levels of over 0.1 ppm causes respiratory problems, liver and kidney damage, and carcinogenicity.Due to its easy operation and of various cheap adsorbents development, adsorption has been proved to be efficient and most economically attractive technique and feasible to the removal of toxic heavy metal from wastewater. The study aimed to report the removal of Cr(VI) ions from aqueous solutions through adsorption process using carboxymethyl cellulose-graft-poly(acrylic acid) (CMC-g-PAA) hydrogel as adsorbent.Effect of pH was studied to remove hexavalent chromium.Graft copolymerization of poly(acrylic acid) onto carboxymethyl cellulose was carried out in the presence of benzoyl peroxide redox initiator and methylenbisacrylamide as crosslinker agent. Batch experiments were carried out to investigate the effects ofinitial pH.The adsorption of Cr(VI) ions as a function of pH was conducted in the initial pH range of 1 to 8. The results indicated that acidic pH strongly favored the adsorption. The optimum pH for adsorption of Cr(VI) ranged from 1 to 3, and the maximum uptake of Cr(VI) from the solution was 6.53 mg/g at pH 1 and 30°C. FTIR spectroscopy, SEM analyses were performed on the adsorbent before and after Cr(VI) binding. All analyses confirmed the complexation of Cr(VI) ions on the adsorbent.

  8. The adsorption behavior and mechanism investigation of Cr(VI ions removal by poly(2-(dimethylaminoethyl methacrylate/poly(ethyleneimine gels

    Directory of Open Access Journals (Sweden)

    Hou Zhengbo

    2015-01-01

    Full Text Available The composite hydrogels based on N,N’-dimethylamino ethyl methacrylate (DMAEMA and polyethyleneimine (PEI were prepared by amino radical polymerization and confirmed by Fourier Transform Infrared Spectra (FTIR and elemental analysis. Then adsorption behavior and mechanism of Cr(VI ions on the obtained materials were investigated with scanning electron microscope, Zeta potential and thermal gravity analysis, etc. The adsorption process was found to follow the pseudo-second order kinetics and Langmuir model, and the maximum adsorption capacity of Cr(VI ions reached 122.8 mg g-1. X-ray photoelectron spectroscopy (XPS and pH analysis revealed that the Cr(VI ions were adsorbed into the gels through electrostatic interaction mechanism, and SO42- in the solution had a great effect on the adsorption process. In addition, high pH and ionic strength could reduce the uptakes of adsorbate, which could be used for desorption of Cr(VI ions from the gels.

  9. Zinc Metal-Organic Framework for Selective Detection and Differentiation of Fe(III) and Cr(VI) Ions in Aqueous Solution.

    Science.gov (United States)

    Lv, Rui; Li, Hui; Su, Jian; Fu, Xin; Yang, Boyi; Gu, Wen; Liu, Xin

    2017-10-16

    A new luminescent Zn(II)-based metal-organic framework (MOF), [Zn 2 (TPOM)(NDC) 2 ]·3.5H 2 O (Zn-MOF; TPOM = tetrakis(4-pyridyloxymethylene)methane and H 2 ndc = 2,6-naphthalenedicarboxylic acid), was successfully synthesized by a hydrothermal reaction. The MOF exhibits excellent luminescence emission, and it can detect Fe(III) and Cr(VI) ions with high selectivity, well antiinterference performance, and short response time. In addition, Zn-MOF was selected as a parent coordination compound to encapsulate Eu 3+ cations to obtain a Eu 3+ -incorporated sample (Eu 3+ @Zn-MOF). Subsequently, we explored the potential application of Eu 3+ @Zn-MOF as a probe for the selective sensing of Fe(III) and Cr(VI) ions, and it revealed that we could differentiate Fe(III) and Cr(VI) ions by the combination Zn-MOF and Eu 3+ @Zn-MOF. More importantly, it represents the first example of MOF-based luminescent sensors which can detect and differentiate Fe(III) and Cr(VI) ions selectively. And the possible sensing mechanism was discussed in detail.

  10. Breakthrough Curve Analysis for Column Dynamics Sorption of Mn(II Ions from Wastewater by Using Mangostana garcinia Peel-Based Granular-Activated Carbon

    Directory of Open Access Journals (Sweden)

    Z. Z. Chowdhury

    2013-01-01

    Full Text Available The potential of granular-activated carbon (GAC derived from agrowaste of Mangostene (Mangostana garcinia fruit peel was investigated in batch and fixed bed system as a replacement of current expensive methods for treating wastewater contaminated by manganese, Mn(II cations. Batch equilibrium data was analyzed by Langmuir, Freundlich, and Temkin isotherm models at different temperatures. The effect of inlet metal ion concentration (50 mg/L, 70 mg/L, and 100 mg/L, feed flow rate (1 mL/min and 3 mL/min, and activated carbon bed height (4.5 cm and 3 cm on the breakthrough characteristics of the fixed bed sorption system were determined. The adsorption data were fitted with well-established column models, namely, Thomas, Yoon-Nelson, and Adams-Bohart. The results were best-fitted with Thomas and Yoon-Nelson models rather than Adams-Bohart model for all conditions. The column had been regenerated and reused consecutively for five cycles. The results demonstrated that the prepared activated carbon was suitable for removal of Mn(II ions from wastewater using batch as well as fixed bed sorption system.

  11. Plutonium sorption onto hematite colloids at femto- and nanomolar concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Romanchuk, A.Yu.; Kalmykov, S.N.; Aliev, R.A. [Lomonosov Moscow State Univ., Moscow (Russian Federation). Radiochemistry Div.

    2011-07-01

    The surface-mediated reduction of Pu(VI) upon sorption onto hematite colloids is addressed in the paper that bring some new light on the mechanisms of interaction of Pu in high valence states with different Fe(III) oxides. We study the sorption of Pu taken at two different total concentrations around 10{sup -9} and 10{sup -14} M using {sup 239}Pu and short-lived {sup 237}Pu tracer. In order to conclude on the mechanisms of Pu sorption onto hematite, the kinetics of sorption of Pu(IV) and Pu(VI) at two concenrations is studied as well as its leaching behavior. The rate limiting step in Pu(VI) sorption is its surface-mediated reduction. The experimental evidence of the polymerization of Pu(IV) on the surface taken at Pu total concentration of {proportional_to} 10{sup -9} M is presented based on the kinetics of sorption and leaching behavior. (orig.)

  12. Ultrasensitive photoelectrochemical determination of chromium(VI) in water samples by ion-imprinted/formate anion-incorporated graphitic carbon nitride nanostructured hybrid

    Energy Technology Data Exchange (ETDEWEB)

    Fang, Tian; Yang, Xiaomin; Zhang, Lizhi; Gong, Jingming, E-mail: jmgong@mail.ccnu.edu.cn

    2016-07-15

    Highlights: • IIP functionalized F-g-C{sub 3}N{sub 4} first applied to Cr(VI) detection. • The first smart integration of F-g-C{sub 3}N{sub 4} with IIP yielding a novel PEC sensing probe. • The system also explored for the speciation determination of chromium species. • The resulting sensor exhibiting fine applicability in real water samples. - Abstract: A rapid and highly sensitive photoelectrochemical (PEC) method has been proposed for the determination of trace amounts of chromium in water samples under visible-light irradiation. Here, a unique nanostructured hybrid of formate anion incorporated graphitic carbon nitride (F-g-C{sub 3}N{sub 4}) is smartly integrated with a Cr(VI) ion-imprinted polymer (IIP) as a photoactive electrode (denoted as IIP@F-g-C{sub 3}N{sub 4}). The nanohybrid of F-g-C{sub 3}N{sub 4} exhibits an enhanced charge separation with substantially improved PEC responses versus g-C{sub 3}N{sub 4}. The newly designed IIP@F-g-C{sub 3}N{sub 4} PEC sensor exhibits high sensitivity and selectivity for the determination of Cr(VI) because it offers efficient photogenerated electron reduction toward Cr(VI). The PEC analysis is highly linear over Cr(VI) concentrations ranging from 0.01 to 100.00 ppb with a detection limit of 0.006 ppb (S/N = 3). Our approach can be used to detect Cr(VI), Cr(III) and the total chromium level in aqueous solution through oxidation of Cr(III) to Cr(VI) and the determination of the total chromium as Cr(VI). In practical applications, this low-cost and sensitive assay has been successfully applied for speciation determination of chromium in environmental water samples.

  13. Simultaneous determination of chromium(III) and chromium(VI) in aqueous solutions by ion chromatography and chemiluminescence detection

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Jøns, O; Nielsen, B

    1992-01-01

    A method for the simultaneous determination of chromium(iii) and chromium(vi) in a flow system based on chemiluminescence was developed. A Dionex cation-exchange guard column was used to separate chromium(iii) from chromium(vi), and chromium(vi) was reduced by potassium sulfite, whereupon both...

  14. Chromium (VI) ion adsorption by grafted cross-linked chitosan beads in aqueous solution - a mathematical and statistical modeling study.

    Science.gov (United States)

    Igberase, E; Osifo, P; Ofomaja, A

    2017-12-01

    Chitosan outstanding qualities and efficient way of binding metal ions even to near zero concentration is the major reason for special attention. Modification of chitosan allows the polymer to be applied in numerous field of research. Depending on the modification techniques, chitosan possesses increased adsorption capacity. In this study chitosan beads (CS) were formulated from chitosan flakes, the beads were cross-linked with glutaraldehyde and thereafter grafted with ethyldiaminetetraacetic acid. The stability and amine concentration of the beads were determined. The chemical functionalities of the beads were obtained by Fourier transform infrared spectroscopy, X-ray diffraction and thermogravimetric analysis (TGA). However, in the adsorption studies with Cr(VI), the number of runs in the experiment was obtained by response surface methodology (RSM), and the maximum adsorption capacity (Qm) from each run was determined from the Langmuir model. The results of the experiment showed that the non-modified beads were soluble at pH 1-4 and insoluble at pH 5, while the modified beads were insoluble at pH 1-6. The amine concentration of CS, CCS and grafted cross-linked chitosan beads (GCCS) were 4.4, 3.8 and 5.0 mmol/g, respectively. The point of zero charge (pHPZC) of GCCS was found to be 4.4. The quadratic model was significant and adequate in describing the experimental data. The difference between experimental and predicted Qm was negligible. From the design matrix and results, increased Qm was achieved at pH 5, contact time 70 min, temperature 45°C, adsorbent dosage 5 g and initial concentration 70 mg/l. The desorption of the beads loaded with Cr(VI) was successful with 0.5 M HCl eluant and contact time of 180 min, leading to cost minimization.

  15. Selective sorption of lead, cadmium and zinc ions by a polymeric cation exchanger containing nano-Zr(HPO3S)2.

    Science.gov (United States)

    Zhang, Qingrui; Pan, Bingcai; Pan, Bingjun; Zhang, Weiming; Jia, Kun; Zhang, Quanxing

    2008-06-01

    A novel polymeric hybrid sorbent, namely ZrPS-001, was fabricated for enhanced sorption of heavy metal ions by impregnating Zr(HPO3S)2 (i.e., ZrPS) nanoparticles within a porous polymeric cation exchanger D-001. The immobilized negatively charged groups bound to the polymeric matrix D-001 would result in preconcentration and permeation enhancement of target metal ions prior to sequestration, and ZrPS nanoparticles are expected to sequester heavy metals selectively through an ion-exchange process. Highly effective sequestration of lead, cadmium, and zinc ions from aqueous solution can be achieved by ZrPS-001 even in the presence of competing calcium ion at concentration several orders of magnitude greater than the target species. The exhausted ZrPS-001 beads are amenable to regeneration with 6 M HCI solution for repeated use without any significant capacity loss. Fixed-bed column treatment of simulated waters containing heavy metals at high or trace levels was also performed. The content of heavy metals in treated effluent approached or met the WHO drinking water standard.

  16. Normal and reverse defect annealing in ion implanted II-VI oxide semiconductors

    Science.gov (United States)

    Azarov, Alexander; Galeckas, Augustinas; Wendler, Elke; Ellingsen, Josef; Monakhov, Edouard; Svensson, Bengt G.

    2017-09-01

    Post-implantation annealing is typically used to remove structural defects and electrically activate implanted dopants in semiconductors. However, ion-induced defects and their interaction with dopants in group II oxide semiconductors are not fully understood. Here, we study defect evolution in the course of annealing in CdO and ZnO materials implanted with nitrogen which is one of the most promising candidates for p-type doping. The results of photoluminescence and ion channeling measurements revealed a striking difference in defect behavior between CdO and ZnO. In particular, the defect annealing in CdO exhibits a two stage behavior, the first stage accounting for efficient removal of point defects and small defect clusters, while the second one involves gradual disappearance of extended defects where the sample decomposition can play a role. In contrast, a strong reverse annealing occurs for ZnO with a maximum defect concentration around 900 °C. This effect occurs exclusively for nitrogen ions and is attributed to efficient growth of extended defects promoted by the presence of nitrogen.

  17. Melanin-embedded materials effectively remove hexavalent chromium (CrVI) from aqueous solution.

    Science.gov (United States)

    Cuong, An Manh; Le Na, Nguyen Thi; Thang, Pham Nhat; Diep, Trinh Ngoc; Thuy, Ly Bich; Thanh, Nguyen Lai; Thang, Nguyen Dinh

    2018-02-23

    Currently, it is recognized that water polluted with toxic heavy metal ions may cause serious effects on human health. Therefore, the development of new materials for effective removal of heavy metal ions from water is still a widely important area. Melanin is being considered as a potential material for removal of heavy metal from water. In this study, we synthesized two melanin-embedded beads from two different melanin powder sources and named IMB (Isolated Melanin Bead originated from squid ink sac) and CMB (Commercial Melanin Bead originated from sesame seeds). These beads were of globular shape and 2-3 mm in diameter. We investigated and compared the sorption abilities of these two bead materials toward hexavalent-chromium (Cr VI ) in water. The isotherm sorption curves were established using Langmuir and Freundlich models in the optimized conditions of pH, sorption time, solid/liquid ratio, and initial concentration of Cr VI . The FITR analysis was also carried out to show the differences in surface properties of these two beads. The optimized conditions for isotherm sorption of Cr VI on IMB/CMB were set at pH values of 2/2, sorption times of 90/300 min, and solid-liquid ratios of 10/20 mg/mL. The maximum sorption capacities calculated based on the Langmuir model were 19.60 and 6.24 for IMB and CMB, respectively. However, the adsorption kinetic of Cr VI on the beads fitted the Freundlich model with R 2 values of 0.992 for IMB and 0.989 for CMB. The deduced Freundlich constant, 1/n, in the range of 0.2-0.8 indicated that these beads are good adsorption materials. In addition, structure analysis data revealed great differences in physical and chemical properties between IMB and CMB. Interestingly, FTIR analysis results showed strong signals of -OH (3295.35 cm - 1 ) and -C=O (1608.63 cm - 1 ) groups harboring on the IMB but not CMB. Moreover, loading of Cr VI on the IMB caused a shift of broad peaks from 3295.35 cm - 1 and 1608.63 cm - 1 to 3354

  18. Effect of sorption conditions on the state of copper(II) ions in the phase of AN-31 ion exchange resin, according to data from ESR and UV-vis diffuse reflectance spectroscopy

    Science.gov (United States)

    Stroganova, E. A.; Anufrienko, V. F.; Larina, T. V.; Vasenin, N. T.; Lebedev, Yu. A.; Parmon, V. N.

    2017-08-01

    It is found that the sorption recovery of copper ions from water solutions in the phase of AN-31 low basicity anion exchanger has a mixed character. It is established via diffuse reflectance spectroscopy that ions are stabilized through complexation with the participation of the functional groups of the sorbent with the formation of structures [Cu(NR3)2(OH)2(H2O)2], [Cu(NR3)3(OH)(H2O)2], and as a result of the physical adsorption of oxide dimers and planar-squared copper clusters. It is shown that increasing the ionic strength of a solution by introducing sodium chloride into the system greatly improves the capacity of the sorbent and leads to the uniform distribution of copper ions in the resin matrix. The similarity between the ESR spectrum parameters of copper-containing samples of the ion exchanger, obtained in a wider range of pH, is determined via ESR and testifies to the homogeneity of the stabilization positions of Cu2+ ions. The crystalline field of tetragonal-elongated octahedron is typical of all Cu2+ ions. All of the complexes have Cu(NO3)2 coordination nodes with the covalent bonding of Cu2+ ions and the amine groups of the sorbent.

  19. Uranium sorption on bentonite modified by octadecyltrimethylammonium bromide

    Energy Technology Data Exchange (ETDEWEB)

    Majdan, Marek, E-mail: marek@hermes.umcs.lublin.pl [Maria Curie Sklodowska University, Faculty of Chemistry, 20-031 Lublin (Poland); Pikus, Stanislaw; Gajowiak, Agnieszka; Sternik, Dariusz [Maria Curie Sklodowska University, Faculty of Chemistry, 20-031 Lublin (Poland); Zieba, Emil [Catholic University of Lublin, SEM Laboratory, 20-718 Lublin (Poland)

    2010-12-15

    Graphical abstract: The influence of pH on U(VI) sorption on ODTMA-bentonite. Research highlights: {yields}ODTMA-bentonite has high sorption affinity for U(VI) in a pH range: 6-10. {yields} Anionic complexes: (UO{sub 2}){sub 3}(OH){sub 7}{sup -} sorption is the most probable. {yields} U(VI) sorption data can be evaluated by straight line dependence. - Abstract: The sorption of U(VI) on octadecyltrimethyl-bentonite was investigated at the pH values of the aqueous phase ranging from 3 to 10 and the concentrations of U(VI): 0.1-1 mmol/dm{sup 3}. The concentrations of alkylammonium cation in bentonite were increased from 21% to 150% of CEC (cation exchange capacity). It was determined that the sorption of U(VI) on modified bentonite, i.e. the distribution constant -K{sub d} decreases with the percent of mineral modification until it attains a minimum at 76% of CEC and then increases again. The effective sorption of U(VI) was found to be in the pH range: 6-10 for the modified bentonite and was explained as the consequence of U(VI) anionic hydroxy complexes sorption. Both FT-IR and XRD spectra of the modified bentonite were analyzed and provided arguments for the existence of surfactant cations in the form of monolayer and bilayer in the interlamellar space of bentonite. In turn the luminescence spectra of bentonite suspensions, i.e. their character at different values of pH, proved the existence of hydroxide-like planar polymeric U(VI) species in the bentonite phase at pH 9.

  20. Superb adsorption capacity of hierarchical calcined Ni/Mg/Al layered double hydroxides for Congo red and Cr(VI) ions

    Energy Technology Data Exchange (ETDEWEB)

    Lei, Chunsheng [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); College of Environmental & Safety Engineering, Changzhou University, Changzhou 213164 (China); Zhu, Xiaofeng [College of Environmental & Safety Engineering, Changzhou University, Changzhou 213164 (China); Zhu, Bicheng; Jiang, Chuanjia; Le, Yao [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Yu, Jiaguo, E-mail: jiaguoyu@yahoo.com [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Department of Physics, Faculty of Science, King Abdulaziz University, Jeddah 21589 (Saudi Arabia)

    2017-01-05

    Highlights: • Ni/Mg/Al layered double hydroxides (NMA-LDHs) synthesized. • NMA-LDHs with hierarchically hollow microsphere structure. • Calcined NMA-LDHs have large adsorption capacities for CR and Cr(VI) ions. - Abstract: The preparation of hierarchical porous materials as catalysts and sorbents has attracted much attention in the field of environmental pollution control. Herein, Ni/Mg/Al layered double hydroxides (NMA-LDHs) hierarchical flower-like hollow microspheres were synthesized by a hydrothermal method. After the NMA-LDHs was calcined at 600 °C, NMA-LDHs transformed into Ni/Mg/Al layered double oxides (NMA-LDOs), which maintained the hierarchical flower-like hollow structure. The crystal phase, morphology, and microstructure of the as-prepared samples were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy elemental mapping, Fourier transform infrared spectroscopy, and nitrogen adsorption−desorption methods. Both the calcined and non-calcined NMA-LDHs were examined for their performance to remove Congo red (CR) and hexavalent chromium (Cr(VI)) ions in aqueous solution. The maximum monolayer adsorption capacities of CR and Cr(VI) ions over the NMA-LDOs sample were 1250 and 103.4 mg/g at 30 °C, respectively. Thermodynamic studies indicated that the adsorption process was endothermic in nature. In addition, the addition of coexisting anions negatively influenced the adsorption capacity of Cr(VI) ions, in the following order: CO{sub 3}{sup 2−} > SO{sub 4}{sup 2−} > H{sub 2}PO{sub 4}{sup −} > Cl{sup −}. This work will provide new insight into the design and fabrication of advanced adsorption materials for water pollutant removal.

  1. Box-Behnken experimental design for chromium(VI) ions removal by bacterial cellulose-magnetite composites.

    Science.gov (United States)

    Stoica-Guzun, Anicuta; Stroescu, Marta; Jinga, Sorin Ion; Mihalache, Nicoleta; Botez, Adriana; Matei, Cristian; Berger, Daniela; Damian, Celina Maria; Ionita, Valentin

    2016-10-01

    In this study bacterial cellulose-magnetite composites were synthesised for the removal of chromium(VI) from aqueous solutions. Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), thermogravimetric analysis and X-ray Photoelectron Spectroscopy (XPS) were used to characterize the bacterial cellulose-magnetite composites and to reveal the uniform dispersion of nanomagnetite in the BC matrix. Magnetic properties were also measured to confirm the magnetite immobilization on bacterial cellulose membrane. The effects of initial Cr(VI) concentration, solution pH and solid/liquid ratio upon chromium removal were examined using the statistical Box-Behnken Design. Because of the possibility of magnetite dissolution during chromium(VI) adsorption, the degree of iron leaching was also analysed in the same conditions as Cr(VI) adsorption. From the factors affecting chromium(VI) adsorption the most important was solution pH. The highest Cr(VI) removal efficiency was observed at pH 4, accompanied by the lowest iron leaching in the solution. The adsorption experiments also indicated that the adsorption process of chromium(VI) is well described by Freundlich adsorption model. Our results proved that the BC-magnetite composites could be used for an efficient removal of chromium(VI) from diluted solutions with a minimum magnetite dissolution during operation. Copyright © 2016 Elsevier B.V. All rights reserved.

  2. APLIKASI PENGOLAHAN POLUTAN ANION KHROM(VI DENGAN MENGGUNAKAN AGEN PENUKAR ION HYDROTALCIT ZN-AI-SO4 (Synthesis of and its Application to Treat Chrom(VI Pollutant Using Hydrotalcite Zn-Al_SO4 as Anion Exchanger

    Directory of Open Access Journals (Sweden)

    Roto Roto

    2009-03-01

    Full Text Available ABSTRAK Keberadaan logam khrom di dalam sistem perairan bersifat polutan yang harus ditangani dengan baik, dan untuk khrom (Vl yang sering dijumpai dalam bentuk anion dapat diolah dengan menggunakan mekanisme pertukaran ion. Suatu agen penukar anion telah dibuat berupa senyawa hidrotalsit Zn-Al-SOa melalui proses sintesis, karakterisasi serta dilakukan pula pengujian aplikasinya untuk pengurangan polutant anion khrom (VI dalam bentuk ion dikromat. Sintesis hidrotalsit Zn-Al-SOa dilakukan dengan metode stoikiometri pada pH 8 dan perlakuan hidrotermal. Aplikasi pertukaran dikromat dengan anion sulfat dalam antar lapis hidrotalsit serta uji regenerasi bahan diamati dengan bantuan analisis struktur dan analisis kinetika reaksi pertukaran. Produk pertukaran ion dikarakterisasi dengan XRD, spektrofotometri IR dan spektrometri serapan atom. Rumus kimia hidrotalsit produk diketahui adalah Zn0,74Al0,26(OH1,74(SO40,13.0,52H2O. Anion dikromat dapat menukar sulfat dalam antarlapis hidrotalsit yang ditunjukkan dalam spektra IR dan pola XRD. Kapasitas pertukaran anion untuk dikromat diketahui 216,84 mek/100 g, sedangkan kinetika reaksi pertukaran ion mengikuti orde dua dengan k = 3 x 10-8 ppm-1.detik-1. Hasil menunjukkan Zn-Al-Cr2O7 dapat mudah diregenerasi.    ABSTRACT  Chrom as pollutant in aquatics system usually establishes as crom (VI and should be worked with special treatment and as an example is ion exchanger. Material Zn-Al-SO4 hydrotalcite product have been synthesized and its application as anion exchanger for dichromate have been studied. Synthesis of Zn-Al-SO4 hydrotalcite was carried out by stoichiometric method at pH 8 and hydrothermal treatment. Sulphate in hydrotalcite interlayer was exchanged by dichromate. Kinetics of ion exchange was also investigated. The product of ion exchange was characterized by XRD, IR spectrophotometry and atomic adsorption  spectrometry. The chemical formula of the  hydrotalcite is Zn0.74Al0.26(OH1.74(SO4 0

  3. Room temperature synthesis of hydrated nickel(III) oxide and study of its effect on Cr(VI) ions removal and bacterial culture

    Science.gov (United States)

    Dey, Sayan; Bhattacharjee, Swarupananda; Bose, Raj Shekhar; Ghosh, Chandan Kr.

    2015-06-01

    Cr(VI) ion is a toxic inorganic affluent that causes carcinogenic effects on the human body. Another problem that requires immediate attention is the fouling of water borne metal surface by micro-organisms. The present study aims to suggest the synthesis of Ni2O3·H2O nanoparticles and to investigate its heavy metal adsorption capacity and bacteriotoxicity in order to address the current global problems. Stable Ni2O3·H2O nanoparticles having various particle sizes were synthesized using active halogenation of nickel(II) precursor at different temperatures. Phase purity was investigated by X-ray diffraction technique. Due to high surface area, surface heterogeneity and surface polarity, they show excellent adsorption affinity (up to 73.9 % removal capacity) of heavy metal ions like Cr(VI). Adsorption isotherms (Freundlich and Langmuir) are plotted for them. Kinetics of the adsorption process reveals it to be pseudo-first-order kinetic in nature. They are also found to be fairly toxic to bacterial subcultures. Maximum value of the minimum inhibitory concentration and minimum bactericidal concentration were found to be ~0.54 and 0.58 mg/l for particles synthesized at 70 °C. It was observed that Cr(VI) adsorption highly depends on the surface heterogeneity, while the bactericidal effect depends on the size of the nanoparticles so-prepared. Hence, the prepared particles could be used as a potential material for Cr(VI) ion removal and as an antifouling agent.

  4. Influence of pH, soil humic/fulvic acid, ionic strength and foreign ions on sorption of thorium(IV) onto {gamma}-Al{sub 2}O{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Chen, C.L. [Institute of Plasma Physics, Chinese Academy of Sciences, P.O. Box 1126, Hefei, Anhui 230031 (China); Wang, X.K. [Institute of Plasma Physics, Chinese Academy of Sciences, P.O. Box 1126, Hefei, Anhui 230031 (China)]. E-mail: xkwang@ipp.ac.cn

    2007-02-15

    The sorption of Th(IV) onto {gamma}-Al{sub 2}O{sub 3} in the absence and presence of soil humic acid (HA)/fulvic acid (FA) was studied by batch technique. The influence of pH from 2 to 12, ionic strength from 0.01M to 0.1M KNO{sub 3}, soil HA/FA concentrations from 2.5mg/L to 17.5mg/L, and foreign cations (Li{sup +}, Na{sup +}, K{sup +}) and anions (NO{sub 3}{sup -}, Cl{sup -}) on the sorption of Th(IV) onto {gamma}-Al{sub 2}O{sub 3} was also tested. The sorption isotherms of Th(IV) were determined at pH 3.50 (+/-0.02) and analyzed with the linear, Freundlich, and Langmuir sorption models, respectively. The results demonstrated that the sorption of Th(IV) onto {gamma}-Al{sub 2}O{sub 3} increases steeply with increasing pH from 2 to 4. HA/FA was shown to enhance Th(IV) sorption at low pH, but to reduce Th(IV) sorption at high pH. It was assumed that the significantly positive influence of HA/FA on Th(IV) sorption onto {gamma}-Al{sub 2}O{sub 3} at pH 2-4 is attributable to the strong surface binding of HA/FA on {gamma}-Al{sub 2}O{sub 3} and subsequently to the formation of ternary surface complexes such as ?SO-O-HA-Th or ?SO-O-FA-Th. The results also demonstrated that the sorption is strongly dependent on the concentration of HA/FA, and slightly dependent on ionic strength. The sorption of Th(IV) onto {gamma}-Al{sub 2}O{sub 3} was also dependent on foreign ions in solution under the experimental conditions.

  5. Removal of dioxouran (VI) cations from aqueous solution by natural sorbents

    Science.gov (United States)

    Naumova, Lyudmila; Gorlenko, Nikolai; Sarkisov, Yurii; Tsvetkov, Nikolai; Shepelenko, Tat'yana; Chukhlomina, Lyudmila

    2017-01-01

    The paper presents investigations of the mechanism of UO22+ cation sorption by natural zeolites and peat from aqueous solutions using a limited volume method. It is proved that the sorption rate depends on sorbent granulating, dioxouran (VI) temperature and concentration. The results show that sorption of UO22+ cations by natural sorbents is the mixed-diffusional mechanism. The use of 24-hour interruption technique (`kinetic memory') demonstrates that in the mixed-diffusional mechanism for natural peat and zeolites the internal ion diffusion predominates. The coefficients of internal diffusion and activation energy are calculated in this paper. The infrared spectroscopy technique and synchronous thermal test are used to identify the interaction between dioxouran (VI) and energy components of natural sorbents. The synchronous thermal test shows that UO22+ cation sorption decreases the thermal stability of peat as compared to its original state. The peat decomposition is determined after UO22+ cation removal as well as the appearance of end-effect maximum of 777.5°C. An assumption is made on a possible decomposition of different metal oxalates in peat and clay peat bonds which irreversibly absorb UO22+ cations. These research findings can be recommended for water purification at nuclear fuel cycle facility.

  6. Batch sorption dynamics and equilibrium for the removal of lead ions from aqueous phase using activated carbon developed from coffee residue activated with zinc chloride.

    Science.gov (United States)

    Boudrahem, F; Aissani-Benissad, F; Aït-Amar, H

    2009-07-01

    Lignocellulosic materials are good precursors for the production of activated carbon. In this work, coffee residue has been used as raw material in the preparation of powder activated carbon by the method of chemical activation with zinc chloride for the sorption of Pb(II) from dilute aqueous solutions. The influence of impregnation ratio (ZnCl2/coffee residue) on the physical and chemical properties of the prepared carbons was studied in order to optimize this parameter. The optimum experimental condition for preparing predominantly microporous activated carbons with high pore surface area (890 m2/g) and micropore volume (0.772 cm3/g) is an impregnation ratio of 100%. The developed activated carbon shows substantial capability to sorb lead(II) ions from aqueous solutions and for relative impregnation ratios of 75 and 100%, the maximum uptake is practically the same. Thus, 75% represents the optimal impregnation ratio. Batch experiments were conducted to study the effects of the main parameters such as contact time, initial concentration of Pb(II), solution pH, ionic strength and temperature. The maximum uptake of lead(II) at 25 degrees C was about 63 mg/g of adsorbent at pH 5.8, initial Pb(II) concentration of 10 mg/L, agitation speed of 200 rpm and ionic strength of 0.005 M. The kinetic data were fitted to the models of pseudo-first order and pseudo-second order, and follow closely the pseudo-second order model. Equilibrium sorption isotherms of Pb(II) were analyzed by the Langmuir, Freundlich and Temkin isotherm models. The Freundlich model gives a better fit than the others. Results from this study suggest that activated carbon produced from coffee residue is an effective adsorbent for the removal of lead from aqueous solutions and that ZnCl2 is a suitable activating agent for the preparation of high-porosity carbons.

  7. TECHNETIUM SORPTION MEDIA REVIEW

    Energy Technology Data Exchange (ETDEWEB)

    DUNCAN JB; KELLY SE; ROBBINS RA; ADAMS RD; THORSON MA; HAASS CC

    2011-08-25

    This report presents information and references to aid in the selection of 99Tc sorption media for feasibility studies regarding the removal of 99Tc from Hanford's low activity waste. The report contains literature search material for sorption media (including ion exchange media) for the most tested media to date, including SuperLig 639, Reillex HPQ, TAM (Kruion), Purolite A520E and A530E, and Dowex 1X8. The U.S. Department of Energy (DOE), Office of River Protection (ORP) is responsible for management and completion of the River Protection Project (RPP) mission, which comprises both the Hanford Site tank farms and the Waste Treatment and Immobilization Plant (WTP). The RPP mission is to store, retrieve and treat Hanford's tank waste; store and dispose of treated wastes; and close the tank farm waste management areas and treatment facilities in a safe, environmentally compliant, cost-effective and energy-effective manner.

  8. Response surface methodological approach for the optimization of adsorption process in the removal of Cr(VI) ions by Cu2(OH)2CO3 nanoparticles

    Science.gov (United States)

    Srivastava, Varsha; Sharma, Y. C.; Sillanpää, Mika

    2015-01-01

    Cu2(OH)2CO3 nanoparticles were synthesized and characterized by XRD, TEM, SEM and ATR-FTIR. SEM suggested the porous nature of nanoparticles. BET surface area of nanoparticles was measured to be 87 m2 g-1. Cu2(OH)2CO3 nanoparticles were used as adsorbent for the removal of Cr(VI) ions from aqueous solutions and wastewater of the printing press. The central composite design (CCD) of the response surface methodology was employed to optimize important adsorption parameters viz. initial Cr(VI) concentration, pH and dose. Analysis of variance (ANOVA) of the quadratic model suggested that experimental data were excellently fitted to the quadratic model. Optimum conditions for approximately 99% removal of Cr(VI) from synthetic wastewater were determined to be pH 6.5, initial concentration of 550 mg/L, adsorbent dose 0.69 g. The kinetic data for Cr(VI) adsorption were best fitted to the pseudo second order model. The Langmuir adsorption capacity of the adsorbent was determined as 87.72 mg/g. Thermodynamic analysis revealed that the adsorption process was spontaneous and endothermic. Desorption study confirms its reusability up to four adsorption-desorption cycles. Cu2(OH)2CO3 nanoparticles also showed efficient removal in presence of anions like SO42-, PO43-, NO32- and Cl-. Findings of the present study suggest that Cu2(OH)2CO3 is a suitable adsorbent material for the removal of Cr(VI) from aqueous solutions and wastewater.

  9. Laser-ignited frontal polymerization of shape-controllable poly(VI-co-AM) hydrogels based on 3D templates toward adsorption of heavy metal ions

    Science.gov (United States)

    Fan, Suzhen; Liu, Sisi; Wang, Xiao-Qiao; Wang, Cai-Feng; Chen, Su

    2016-06-01

    Given the increasing heavy metal pollution issue, fast preparation of polymeric hydrogels with excellent adsorption property toward heavy metal ions is very attractive. In this work, a series of poly( N-vinylimidazole-co-acrylamide) (poly(VI-co-AM)) hydrogels were synthesized via laser-ignited frontal polymerization (LIFP) for the first time. The dependence of frontal velocity and temperature on two factors monomer ratios and initiator concentrations was systematically investigated. Poly(VI-co-AM) hydrogels with any self-supporting shapes can be synthesized by a one-step LIFP in seconds through the application of 3D templates. These shape-persistent hydrogels are pH-responsive and exhibit excellent adsorption/desorption characteristics toward Mn(II), Zn(II), Cd(II), Ni(II), Cu(II) and Co(II) ions, and the adsorption conformed to the pseudo-second-order kinetic model. The reusability of the hydrogels toward mental ions adsorption was further researched, which suggested that the hydrogels can be reused without serious decrease in adsorption capacity. This work might open a promising strategy to facilely prepare shape-controllable hydrogels and expand the application of LIFP.

  10. Zeolitic imidazolate framework-8 for efficient adsorption and removal of Cr(VI) ions from aqueous solution.

    Science.gov (United States)

    Niknam Shahrak, Mahdi; Ghahramaninezhad, Mahboube; Eydifarash, Mohsen

    2017-04-01

    Heavy metals are emerging toxic pollutants in which the development of advanced materials for their efficient adsorption and separation is thus of great significance in environmental sciences point of view. In this study, one of the zinc-based zeolitic imidazolate framework materials, known as ZIF-8, has been synthesized and used for chromium(VI) contaminant removal from water for the first time. The as-synthesized ZIF-8 adsorbent was characterized with different methodologies such as powder X-ray diffraction (XRD), thermo-gravimetric analysis, FT-IR, nuclear magnetic resonance spectroscopy, and UV-Vis spectra of solid state. Various factors affecting removal percentage (efficiency) are experimentally investigated including pH of solution, adsorbent dosage, contact time and initial concentration of Cr(VI) to achieve the optimal condition. The obtained results indicate that the ZIF-8 shows good performance for the Cr(VI) removal from aqueous solution so that 60 min mixing of 2 g of ZIF-8 adsorbent with the 2.5 ppm of Cr(VI) solution in a neutral environment will result in the highest separation efficiency around 70%. The time needed to reach the equilibrium (maximum separation efficiency) is only 60 min for a concentration of 5 mg L -1 . Structure stability in the presence of water is also carefully examined by XRD determination of ZIF-8 under different contact times in aqueous solution, which suggests that the structure is going to be destructed after 60 min immersed in solution. Electrostatic interaction of Cr(VI) anions by positively charged ZIF-8 is responsible for Cr(VI) adsorption and separation. Moreover, equilibrium adsorption study reveals that the Cr(VI) removal process using ZIF-8 nicely fits the Langmuir and Toth isotherm models which mean the adsorbent has low heterogeneous surface with different distributions of adsorption energies during Cr(VI) adsorption. Equilibrium adsorption capacity is observed around 0.25 for 20 mg L -1 of initial Cr(VI

  11. Superb adsorption capacity of hierarchical calcined Ni/Mg/Al layered double hydroxides for Congo red and Cr(VI) ions.

    Science.gov (United States)

    Lei, Chunsheng; Zhu, Xiaofeng; Zhu, Bicheng; Jiang, Chuanjia; Le, Yao; Yu, Jiaguo

    2017-01-05

    The preparation of hierarchical porous materials as catalysts and sorbents has attracted much attention in the field of environmental pollution control. Herein, Ni/Mg/Al layered double hydroxides (NMA-LDHs) hierarchical flower-like hollow microspheres were synthesized by a hydrothermal method. After the NMA-LDHs was calcined at 600°C, NMA-LDHs transformed into Ni/Mg/Al layered double oxides (NMA-LDOs), which maintained the hierarchical flower-like hollow structure. The crystal phase, morphology, and microstructure of the as-prepared samples were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy elemental mapping, Fourier transform infrared spectroscopy, and nitrogen adsorption-desorption methods. Both the calcined and non-calcined NMA-LDHs were examined for their performance to remove Congo red (CR) and hexavalent chromium (Cr(VI)) ions in aqueous solution. The maximum monolayer adsorption capacities of CR and Cr(VI) ions over the NMA-LDOs sample were 1250 and 103.4mg/g at 30°C, respectively. Thermodynamic studies indicated that the adsorption process was endothermic in nature. In addition, the addition of coexisting anions negatively influenced the adsorption capacity of Cr(VI) ions, in the following order: CO3(2-)>SO4(2-)>H2PO4(-)>Cl(-). This work will provide new insight into the design and fabrication of advanced adsorption materials for water pollutant removal. Copyright © 2016 Elsevier B.V. All rights reserved.

  12. In situ preparation of powder and the sorption behaviors of molecularly imprinted polymers through the complexation between polymer ion of methyl methacrylate/acrylic acid and Ca++ ion.

    Science.gov (United States)

    Chough, Sung Hyo; Park, Kwang Ho; Cho, Seung Jin; Park, Hye Ryoung

    2014-09-02

    Molecularly imprinted polymer (MIP) powders were prepared using a simple complexation strategy between the polymer carboxylate groups and template molecule followed by metal cation cross-linking of residual polymer carboxylates. Polymer powders were formed in situ by templating carboxylic acid containing polymers with 4-ethylaniline (4-EA), followed by addition of an aqueous CaCl2 solution. The solution remained homogeneous. The powders were prepared by precipitation by slowly adding a non-solvent, H2O, to the mixture. The resulting particles were very porous with uptake capacity that approached the theoretical value. We suggest two types of complexes are formed between the template, 4-EA, and polymer. The isolated entry type forms well defined cavities for the template with high specific selectivity, while the adjacent entry type forms wider binding sites without specific sorption for isomeric molecules. To evaluate conditions for forming materials with high affinity and selectivity, three MIPs were prepared containing 0.5, 1.0, and 1.5 equivalents of template to the base polymer. The MIP containing 0.5 eq showed higher specific selectivity to 4-EA, but the MIP containing 1.5 eq had noticeably lower selectivity. The lower selectivity is attributed to poorly formed binding sites with little selective sorption to any isomer when the higher ratio of template was used. However at the lower ratio of template the isolated entry is preferably formed to produce well defined binding cavities with higher selectivity to template. Copyright © 2014 Elsevier B.V. All rights reserved.

  13. Evaluation of ion exchange-modified Y and ZSM5 zeolites in Cr(VI) biosorption and catalytic oxidation of ethyl acetate

    OpenAIRE

    Silva, Bruna Andreia Nogueira Airosa; Figueiredo, Hugo; Soares, O. S. G. P.; Pereira, M. de F. R.; Figueiredo, J.L.; Lewandowska, A. E.; Bañares, M. A.; Neves, I.C.; Tavares,M. T.

    2012-01-01

    The aim of this work was the evaluation of the performance of two zeolites with different structures (FAU and MFI) and acidity properties in the biosorption of Cr(VI) and catalytic oxidation of ethyl acetate. The starting zeolites, Y (FAU) and ZSM5 (MFI), were modified by ion exchange treatments with NaNO3 in order to obtain zeolites with different acidity and sodium content. A biosorption system consisting of a bacterium, Arthrobacter viscosus, supported on the different zeolites was used fo...

  14. Comparative and competitive adsorption of Cr(VI), As(III), and Ni(II) onto coconut charcoal.

    Science.gov (United States)

    Wu, Yunhai; Wen, Yajun; Zhou, Jianxin; Cao, Julin; Jin, Yanping; Wu, Yunying

    2013-04-01

    This study evaluates the behavior of coconut charcoal (AC) to adsorb Cr(VI), As(III), and Ni(II) in mono- and multicomponent (binary and ternary) systems. Batch experiments were carried out for mono- and multicomponent systems with varying metal ion concentrations to investigate the competitive adsorption characteristics. The adsorption kinetics followed the mechanism of the pseudo-second-order equation in both single and binary systems, indicating chemical sorption as the rate-limiting step of adsorption mechanism. Equilibrium studies showed that the adsorption of Cr(VI), As(III), and Ni(II) followed the Langmuir model and maximum adsorption capacities were found to be 5.257, 0.042, and 1.748 mg/g, respectively. In multicomponent system, As(III) and Ni(II) adsorption competed intensely, while Cr(VI) adsorption was much less affected by competition than As(III) and Ni(II). With the presence of Cr(VI), the adsorption capacities of As(III) and Ni(II) on AC were higher than those in single system and the metal sorption followed the order of Ni(II) > As(III) > Cr(VI). The results from the sequential adsorption-desorption cycles showed that AC adsorbent held good desorption and reusability.

  15. Biosorption of copper(II and chromium(VI by modified tea fungus

    Directory of Open Access Journals (Sweden)

    Šćiban Marina B.

    2012-01-01

    Full Text Available The tea fungus was found to have good adsorption capacities for heavy metal ions. In this work it was treated with HCl or NaOH at 20°C or 100°C, with the aim to improve its adsorption ability. The sorption of Cu(II and Cr(VI ions from aqueous solutions by raw and treated tea fungus was investigated in the batch mode. The largest quantity of adsorbed Cu(II, of about 55 mg/g, was achieved by tea fungus modified with NaOH at 100°C. For Cr(VI, the largest quantity of adsorbed anions, of about 58 mg/g, was achieved by the adsorbent modified with NaOH at 20°C. It was shown that acid modification of tea fungus biomass was not effective. [Projekat Ministarstva nauke Republike Srbije, br. III 43005 i br. TR 31002

  16. Synthesis of polyacrylate/polyethylene glycol interpenetrating network hydrogel and its sorption of heavy-metal ions

    Directory of Open Access Journals (Sweden)

    Qunwei Tang, Xiaoming Sun, Qinghua Li, Jihuai Wu and Jianming Lin

    2009-01-01

    Full Text Available A simple two-step aqueous polymerization method was introduced to synthesize a polyacrylate/polyethylene glycol (PAC/PEG interpenetrating network (IPN hydrogel. On the basis of the effects of the ratio of PAC to PEG, neutralization degree, heavy-metal ion concentration, and temperature on the adsorption behavior of PAC/PEG IPN hydrogel toward Ni2 +, Cr3 + and Cd2 +, the preparation conditions were optimized. In our system, the greatest amount of Ni2 +, Cr3 + and Cd2 + adsorbed were 102.34, 49.38 and 33.41 mg g- 1, respectively. The adsorption abilities of a dried PAC/PEG composite and a swollen PAC/PEG IPN hydrogel were compared. It was found that the efficiency of removing metal ions using the swollen hydrogel was greater than that using the dried composite. The adsorption mechanism and model are also discussed.

  17. Thermodynamics of cationic surfactant sorption onto natural clinoptilolite

    Energy Technology Data Exchange (ETDEWEB)

    Sullivan, E.J.; Bowman, R.S. [New Mexico Inst. of Mining and Technology, Socorro, NM (United States); Carey, J.W. [Los Alamos National Lab., NM (United States)

    1998-10-15

    Sorption enthalpies of hexadecyltrimethylammonium bromide (HDTMA) as monomers and micelles and tetraethylammonium bromide (TEA) were used with surfactant, counterion, and co-ion sorption isotherms to infer the conformation, sorption mechanism, and relative stability of the sorbed surfactants on natural clinoptilolite. The average value of the sorption enthalpy was {minus}10.38 kJ/mol for monomers, {minus}11.98 kJ/mol for micelles, and +3.03 kJ/mol for TEA. Sorption of monomers produced a lower sorption plateau than equivalent micelle sorption (maxima 145 mmol/kg, 225 mmol/kg). Analysis of the sorption data demonstrated a change in the sorption mechanism at the external cation exchange capacity (ECEC) of clinoptilolite. Sorption data from below and above the ECEC were fit to a simple polynomial model and the Gibbs free energy of sorption ({Delta} G{sub m}{sup 0}) and sorption entropies were calculated. Resultant values of {Delta} G{sub m}{sup 0} were {minus}9.27 and {minus}14.38 kJ/mol for HDTMA monomers and micelles, respectively, for sorption below the ECEC, and {minus}16.11 and {minus}23.10 kJ/mol, respectively, for sorption above the ECEC. The value for TEA was {minus}1.04 kJ/mol, indicating weaker sorption than for HDTMA. Monomer sorption to clinoptilolite exceeded the ECEC, even when the solution concentration was below the critical micelle concentration. Hydrophobic (tail-tail) components of {Delta} G{sub m}{sup 0} were the driving force for sorption of HDTMA, both below and above the ECEC. A significant kinetic effect was observed in the sorption isotherms with a period of rapid sorption followed by slow equilibration requiring 7 days to achieve steady state for HDTMA; TEA equilibration occurred within 24 h.

  18. Periodic Density Functional Theory Investigation of the Uranyl Ion Sorption on Three Mineral Surfaces: A Comparative Study

    Directory of Open Access Journals (Sweden)

    Eric Simoni

    2009-06-01

    Full Text Available Canister integrity and radionuclides retention is of prime importance for assessing the long term safety of nuclear waste stored in engineered geologic depositories. A comparative investigation of the interaction of uranyl ion with three different mineral surfaces has thus been undertaken in order to point out the influence of surface composition on the adsorption mechanism(s. Periodic DFT calculations using plane waves basis sets with the GGA formalism were performed on the TiO2(110, Al(OH3(001 and Ni(111 surfaces. This study has clearly shown that three parameters play an important role in the uranyl adsorption mechanism: the solvent (H2O distribution at the interface, the nature of the adsorption site and finally, the surface atoms’ protonation state.

  19. An ATR-FTIR study of sulphate sorption on magnetite; rate of adsorption, surface speciation, and effect of calcium ions.

    Science.gov (United States)

    Roonasi, Payman; Holmgren, Allan

    2009-05-01

    The adsorption of sulphate on magnetite was studied in-situ using ATR-FTIR spectroscopy. Synthetic magnetite particles were deposited on a ZnSe internal reflection element and the spectra of sulphate adsorbed at pH 4-8.5 were recorded. Two different ionic strengths were used viz. 0.01 M and 0.1 M NaCl. The spectra of adsorbed sulphate on magnetite coated ZnSe were compared with the spectra of sulphate solutions at the same pH values and in contact with uncoated ZnSe. The spectrum of adsorbed sulphate at pH 4 showed three maxima at 979, 1044, and 1115 cm(-1) indicating a monodentate adsorption in which the T(d) symmetry of SO(4)(2-) is lowered to C(3v). At pH 6.5, sulphate adsorbed as an outer-sphere complex with two weak bands appearing at 1102 and 980 cm(-1). Moreover, spectra of the adsorbed sulphate at pH 4 were recorded as a function of time and sulphate concentration. The equilibrium absorbance at different concentrations fitted a Langmuir type adsorption isotherm. The Langmuir affinity constant K at pH 4 was determined from the slope and intercept of the Langmuir plot to be K=1.2344x10(4) M(-1) and the Gibbs free energy of adsorption DeltaG(ads)(0) was estimated from this value to be -33.3 kJ/mol. Kinetic analysis indicated that adsorption at pH 4 is fast, whilst the desorption kinetic at the same pH is very slow. In addition, the effect of Ca ions on sulphate adsorption was also studied. It was shown that Ca ions increased the sulphate adsorption on magnetite at pH 8.5.

  20. Sorption of Cd2+ Ions From Aqueous Solutions on Organic Wastes / Sorpcja Jonów Cd2+ Z Roztworów Wodnych Na Odpadach Organicznych

    Science.gov (United States)

    Bożęcka, Agnieszka; Sanak-Rydlewska, Stanisława

    2015-09-01

    This article presents the results of research on the Cd2+ ions sorption from model aqueous solutions on sunflower hulls, walnut shells and plum stones. The effect of various factors, such as mass of the natural sorbent, the pH, the time and the temperature was studied. The process of Cd2+ ions sorption on studied sorbents was described by the Langmuir model. The best sorption capacity has been achieved for sunflower hulls. The maximum sorption capacity for this material was 19.93 mg/g. W artykule przedstawiono wyniki badań, które dotyczyły usuwania jonów Cd2+ z modelowych roztworów wodnych za pomocą odpadów organicznych, takich jak: łuski słonecznika, łupiny orzecha włoskiego i pestki śliwek. Wykazano, iż badane materiały mogą być skutecznie wykorzystywane do usuwania jonów Cd2+ z modelowych roztworów wodnych w układach jednoskładnikowych. Dla badanego zakresu stężeń i przyjętych warunków procesu sorpcji w układach jednoskładnikowych, największą wydajność sorpcji jonów Cd2+, osiągnięto dla łuszczyn słonecznika. Wyniosła ona 81,75-93,02%. Dla pozostałych materiałów sorpcja jest nieco niższa, ale również zadowalająca. W pracy podano interpretację otrzymanych wyników w oparciu o jeden z najpopularniejszych modeli izoterm adsorpcji - Langmuira, który potwierdził, iż najlepszym sorbentem jonów Cd2+, spośród badanych, są łuszczyny słonecznika. Materiał ten cechuje się największą wartością parametrów qmax i b izotermy Langmuira. W tym przypadku stała qmax, wyrażająca pojemność monowarstwy, przyjęła wartość 19,93 mg/g, a parametr b, określający powinowactwo do usuwanych jonów wynosi 0,2264 dm3/mg (Rys. 5, Tab. 1). Udowodniono również, że proces sorpcji jonów Cd2+ na badanych sorbentach organicznych zależy od masy sorbentu. Dla wszystkich materiałów stopień usunięcia jonów Cd2+ z roztworów wodnych rośnie ze wzrostem masy sorbentu, aż do uzyskania maksimum przy naważce 0,5 g (Rys. 1

  1. Radiation-induced reduction of U(VI) ion at 6>pH>4 as observed by fast conductimetry

    Science.gov (United States)

    Broszkiewicz, Roman K.; Vojnovic, Borivoj; Michael, Barry D.

    Reactions between U(VI) and ionic species produced upon irradiation of aqueous (pH 4.4 or 5.5) and acetonic solutions have been observed directly using a.c. conductivity. Apart from e -aq also H 3O + reacts rapidly with hydroxides of the UO 2+2. An electron pulse of 20 ns duration starts a sequence of phenomena which does not terminated until ca. 10 s.

  2. Layered Double Hydroxides as Effective Adsorbents for U(VI and Toxic Heavy Metals Removal from Aqueous Media

    Directory of Open Access Journals (Sweden)

    G. N. Pshinko

    2013-01-01

    Full Text Available Capacities of different synthesized Zn,Al-hydrotalcite-like adsorbents, including the initial carbonate [Zn4Al2(OH12]·CO3·8H2O and its forms intercalated with chelating agents (ethylenediaminetetraacetic acid (EDTA, diethylenetriaminepentaacetic acid (DTPA, and hexamethylenediaminetetraacetic acid (HMDTA and heat-treated form Zn4Al2O7, to adsorb uranium(VI and ions of toxic heavy metals have been compared. Metal sorption capacities of hydrotalcite-like adsorbents have been shown to correlate with the stability of their complexes with the mentioned chelating agents in a solution. The synthesized layered double hydroxides (LDHs containing chelating agents in the interlayer space are rather efficient for sorption purification of aqueous media free from U(VI irrespective of its forms of natural abundance (including water-soluble bi- and tricarbonate forms and from heavy metal ions. [Zn4Al2(OH12]·EDTA·nH2O is recommended for practical application as one of the most efficient and inexpensive synthetic adsorbents designed for recovery of both cationic and particularly important anionic forms of U(VI and other heavy metals from aqueous media. Carbonate forms of LDHs turned out to be most efficient for recovery of Cu(II from aqueous media with pH0≥7 owing to precipitation of Cu(II basic carbonates and Cu(II hydroxides. Chromate ions are efficiently adsorbed from water only by calcinated forms of LDHs.

  3. Extraction of actinide (III, IV, V, VI) ions and TcO4- byN,N,N',N'- tetraisobutyl-3-oxa-glutaramide

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Guoxin; Zhang, Ping; Wang, Jianchen; Rao, Linfeng

    2005-05-01

    The extraction behavior of U(VI), Np(V), Pu(IV), Am(III), and TcO{sub 4}{sup -} with N, N, N', N'-tetraisobutyl-3-oxa-glutaramide (TiBOGA) were investigated. An organic phase of 0.2 mol/L TiBOGA in 40/60% (V/V) 1-octanol/kerosene showed good extractability for actinides (III, IV, V VI) and TcO{sub 4}{sup -}from aqueous solutions of HNO{sub 3} (0.1 to 4 mol/L). At 25 C, the distribution ratio of the actinide ions (D{sub An}) generally increased as the concentration of HNO{sub 3} in the aqueous phase was increased from 0.1 to 4 mol/L, while the D{sub Tc} at first increased, then decreased, with a maximum of 3.0 at 2 mol/L HNO{sub 3}. Based on the slope analysis of the dependence of D{sub M} (M = An or Tc) on the concentrations of reagents, the formula of extracted complexes were assumed to be UO{sub 2}L{sub 2}(NO{sub 3}){sub 2}, NpO{sub 2}L{sub 2}(NO{sub 3}), PuL(NO{sub 3}){sub 4}, AmL{sub 3}(NO{sub 3}){sub 3}, and HL{sub 2}(TcO{sub 4}) where L = TiBOGA. The enthalpy and entropy of the corresponding extraction reactions, {Delta}{sub r}H and {Delta}{sub r}S, were calculated from the dependence of D on temperature in the range of 15-55 C. For U(VI), Np(V), Am(III) and TcO{sub 4}{sup -}, the extraction reactions are enthalpy driven and disfavored by entropy ({Delta}{sub r}H < 0 and {Delta}{sub r}S < 0). In contrast, the extraction reaction of Pu(IV) is entropy driven and disfavored by enthalpy ({Delta}{sub r}H > 0 and {Delta}{sub r}S > 0). A test run with 0.2 mol/L TiBOGA in 40/60% 1-octanol/kerosene was performed to separate actinides and TcO{sub 4}{sup -} from a simulated acidic high-level liquid waste (HLLW), using tracer amounts of {sup 238}U(VI), {sup 237}Np(V), {sup 239}Pu(VI), {sup 241}Am(III) and {sup 99}TcO{sub 4}{sup -}. The distribution ratios of U(VI), Np(V), Pu(VI), Am(III) and TcO{sub 4}{sup -} were 12.4, 3.9, 87, > 1000 and 1.5, respectively, confirming that TiBOGA is a promising extractant for the separation of all actinides and TcO{sub 4}{sup

  4. An investigation of the applicability of the new ion exchange resin, Reillex{trademark}-HPQ, in ATW separations. Milestone 4, Final report

    Energy Technology Data Exchange (ETDEWEB)

    Ashley, K.R.; Ball, J.; Grissom, M.; Williamson, M.; Cobb, S.; Young, D.; Wu, Yen-Yuan J.

    1993-09-07

    The investigations with the anion exchange resin Reillex{trademark}-HPQ is continuing along several different paths. The topics of current investigations that are reported here are: The sorption behavior of chromium(VI) on Reillex{trademark}-HPQ from nitric acid solutions and from sodium hydroxide/sodium nitrate solutions; sorption behavior of F{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; sorption behavior of Cl{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; sorption behavior of Br{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; and the Honors thesis by one of the students is attached as Appendix II (on ion exchange properties of a new macroperous resin using bromide as the model ion in aqueous nitrate solutions).

  5. Radiation-induced reduction of U(VI) ion at 6>pH>4 as observed by fast conductimetry

    Energy Technology Data Exchange (ETDEWEB)

    Broszkiewicz, R.K. (Institute of Nuclear Chemistry and Technology, Dorodna (Poland)); Vojnovic, B.; Michael, B.D. (Mount Vernon Hospital, Northwood (United Kingdom). Gray Lab.)

    1992-01-01

    Reactions between U(VI) and ionic species produced upon irradiation of aqueous (pH 4.4 or 5.5) and acetonic solutions have been observed directly using a.c. conductivity. Apart from e{sub aq}{sup -} also H{sub 3}O{sup +} reacts rapidly with hydroxides of the UO{sub 2}{sup 2+}. An electron pulse of 20 ns duration starts a sequence of phenomena which does not terminate until ca. 10 s. (author).

  6. Synthesis of titania modified silica-pillared clay (SPC) with highly ordered interlayered mesoporous structure for removing toxic metal ion Cr(VI) from aqueous state

    Science.gov (United States)

    Mao, Huihui; Zhu, Kongnan; Li, Baoshan; Yao, Chao; Kong, Yong

    2014-02-01

    Titanium-functionalized silica-pillared clays synthesized through post synthetic route was utilized as adsorbers for the removal of Cr(VI) ions from aqueous solutions under different temperatures and initial concentrations. The starting mesostructured silica-pillared clay is assembled by intragallery ammonia-catalyzed hydrolysis of tetraethoxysilane using cationic surfactant as gallery template, and subsequently, the formed interlayered pore walls were decorated with nano-sized TiO2 particle through organic titanium functionalization process. The kind of structural transformation has been confirmed by X-ray diffraction (XRD), nitrogen adsorption-desorption isotherms, Fourier transform infrared (FT-IR) analysis, UV-vis diffuse reflectance spectroscopy (DRS), elemental analysis (XRF), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Such results indicate that most of the grafted titanium species was combined with Si-OH on the surface of gallery pores. By changing the concentration of organic titanium source during synthesis, the porous structure system is effected. Under suitable conditions, these materials exhibit high adsorption capacity and efficiency. Qualitative estimates of the thermodynamic parameters showed that the overall adsorption process is spontaneous (ΔG° 0). The adsorption isotherms of Cr(VI) on titanium-functionalized silica-pillared clay were best fitted by Redlich-Peterson models. Detail results of thermodynamics and kinetics are also presented.

  7. Uranium sorption on bentonite modified by octadecyltrimethylammonium bromide.

    Science.gov (United States)

    Majdan, Marek; Pikus, Stanisław; Gajowiak, Agnieszka; Sternik, Dariusz; Zięba, Emil

    2010-12-15

    The sorption of U(VI) on octadecyltrimethyl-bentonite was investigated at the pH values of the aqueous phase ranging from 3 to 10 and the concentrations of U(VI): 0.1-1 mmol/dm(3). The concentrations of alkylammonium cation in bentonite were increased from 21% to 150% of CEC (cation exchange capacity). It was determined that the sorption of U(VI) on modified bentonite, i.e. the distribution constant -K(d) decreases with the percent of mineral modification until it attains a minimum at 76% of CEC and then increases again. The effective sorption of U(VI) was found to be in the pH range: 6-10 for the modified bentonite and was explained as the consequence of U(VI) anionic hydroxy complexes sorption. Both FT-IR and XRD spectra of the modified bentonite were analyzed and provided arguments for the existence of surfactant cations in the form of monolayer and bilayer in the interlamellar space of bentonite. In turn the luminescence spectra of bentonite suspensions, i.e. their character at different values of pH, proved the existence of hydroxide-like planar polymeric U(VI) species in the bentonite phase at pH 9. Copyright © 2010 Elsevier B.V. All rights reserved.

  8. Distinguished Cr(VI) capture with rapid and superior capability using polydopamine microsphere: Behavior and mechanism.

    Science.gov (United States)

    Zhang, Qingrui; Li, Yixuan; Yang, Qinggang; Chen, He; Chen, Xinqing; Jiao, Tifeng; Peng, Qiuming

    2018-01-15

    Toxic heavy metal containing Cr(VI) species is a serious threat for ecological environment and human beings. In this work, a new mussel-inspired polydopamine microsphere (PDA-sphere) is prepared through in situ oxidative polymerization at air condition with controllable sizes. The adsorption of Cr(VI) ions onto PDA-sphere is highly pH dependent with the optimal pH ranging from 2.5 to 3.8. A rapid Cr(VI) removal can approach in 8min for equilibrium. More importantly, the prepared materials exhibit a remarkable sorption selectivity, coexisting SO42-, NO3- and Cl- ions at high levels; The applicability model further proves its effective performances with treated capacity of 42,000kg/kg sorbent, and the effluent can be reduced from 2000ppb to below 50ppb, which meets the drinking water criterions recommended by WHO. 1kg sorbent can also purify approximately 100t Cr(VI) contaminated wastewaters basing on the wastewater discharges of China. Such capacity for application ranks the top level for Cr(VI) removal. Additionally, the exhausted materials can be well regenerated by binary alkaline and salts mixtures. Such efficient adsorption can be ascribed to the well-dispersed morphology as well as the strong affinity between Cr(VI) and catechol or amine groups by XPS investigation. All the results suggest that polydopamine microspheres may be ideal materials for Cr(VI) treatment in waters. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Determination of Pb(II), Zn(II), Cd(II), and Co(II) ions by flame atomic absorption spectrometry in food and water samples after preconcentration by coprecipitation with Mo(VI)-diethyldithiocarbamate.

    Science.gov (United States)

    Tufekci, Mehmet; Bulut, Volkan Numan; Elvan, Hamide; Ozdes, Duygu; Soylak, Mustafa; Duran, Celal

    2013-02-01

    A new, simple, and rapid separation and preconcentration procedure, for determination of Pb(II), Cd(II), Zn(II), and Co(II) ions in environmental real samples, has been developed. The method is based on the combination of coprecipitation of analyte ions by the aid of the Mo(VI)-diethyldithiocarbamate-(Mo(VI)-DDTC) precipitate and flame atomic absorption spectrometric determinations. The effects of experimental conditions like pH of the aqueous solution, amounts of DDTC and Mo(VI), standing time, centrifugation rate and time, sample volume, etc. and also the influences of some foreign ions were investigated in detail on the quantitative recoveries of the analyte ions. The preconcentration factors were found to be 150 for Pb(II), Zn(II) and Co(II), and 200 for Cd(II) ions. The detection limits were in the range of 0.1-2.2 μg L(-1) while the relative standard deviations were found to be lower than 5 % for the studied analyte ions. The accuracy of the method was checked by spiked/recovery tests and the analysis of certified reference material (CRM TMDW-500 Drinking Water). The procedure was successfully applied to seawater and stream water as liquid samples and baby food and dried eggplant as solid samples in order to determine the levels of Pb(II), Cd(II), Zn(II), and Co(II) ions.

  10. Microwave-induced synthesis of pyrophosphate Zr{sub 1-x}Ti{sub x}P{sub 2}O{sub 7} and TiP{sub 2}O{sub 7} with enhanced sorption capacity for uranium (VI)

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Rui [State Key Laboratory of Fine Chemicals, School of Chemical Engineering, Dalian University of Technology, Dalian 116024 (China); School of Chemistry and Materials Science, Liaoning Shihua University, Fushun 113001 (China); Ye, Junwei, E-mail: junweiye@dlut.edu.cn [State Key Laboratory of Fine Chemicals, School of Chemical Engineering, Dalian University of Technology, Dalian 116024 (China); Rauf, Abdul [State Key Laboratory of Fine Chemicals, School of Chemical Engineering, Dalian University of Technology, Dalian 116024 (China); Wu, Xiaomeng; Liu, Hongxue [School of Chemistry and Materials Science, Liaoning Shihua University, Fushun 113001 (China); Ning, Guiling, E-mail: ninggl@dlut.edu.cn [State Key Laboratory of Fine Chemicals, School of Chemical Engineering, Dalian University of Technology, Dalian 116024 (China); Jiang, Heng, E-mail: hjiang78@hotmail.com [School of Chemistry and Materials Science, Liaoning Shihua University, Fushun 113001 (China)

    2016-09-05

    Highlights: • New zirconium titanium pyrophosphates Zr{sub 1-x}Ti{sub x}P{sub 2}O{sub 7} were synthesized. • A facile microwave induced route was employed. • The adsorption capacity of Zr{sub 1-x}Ti{sub x}P{sub 2}O{sub 7} for U(VI) was adjusted by Ti content. • The maximum amount of TiP{sub 2}O{sub 7} for U(VI) reached up to 309.8 mg g{sup −1}. • Adsorption kinetics and thermodynamic analysis of Zr{sub 1-x}Ti{sub x}P{sub 2}O{sub 7} were performed. - Abstract: A series of nanostructured pyrophosphates Zr{sub 1-x}Ti{sub x}P{sub 2}O{sub 7} (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, and 1.0), have been prepared via a facile microwave induced route in which zirconium hydroxide, titanium hydroxide and phosphoric acid were used as Zr, Ti and P sources, respectively. It is demonstrated the isomorphous substitution of Zr{sup 4+} by Ti{sup 4+} results in a decrease of the size and an enhancement of the adsorption capacity of the obtained particles for U(VI) in aqueous solution. The maximum amount of TiP{sub 2}O{sub 7} for U(VI) reached up to 309.8 mg g{sup −1} under the experimental conditions (pH = 5, t = 60 min and T = 303 K). The as-obtained specific metal pyrophosphates exhibit a considerably higher adsorption capability for U(VI) in aqueous solution compared with Zr{sub 1-x}Ti{sub x}P{sub 2}O{sub 7} prepared by calcined method, showing a high potential for U(VI) sequestration applications. The adsorption kinetics and thermodynamic analysis of Zr{sub 1-x}Ti{sub x}P{sub 2}O{sub 7} on adsorption of U (VI) were performed, and a possible adsoprtion mechanism was also proposed.

  11. Studies of kinetic of Cr(VI) adsorption in chitosan magnetic particles by radiochemistry method; Estudo da cinetica de adsorcao de Cr(VI) em particulas magneticas de quitosana pelo metodo radioquimico

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, Levi S.; Yamaura, Mitiko; Camilo, Ruth L. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)]. E-mail: lsrodri@ipen.br; Landgraf, Fernando J.G. [Instituto de Pesquisas Tecnologicas (IPT), Sao Paulo, SP (Brazil)]. E-mail: landgraf@ipt.br

    2005-07-01

    There are a number of processes which are used for remove or recovery metals from waters and waste waters. However, such processes are expensive and sometimes ineffective, especially when metals are present in solution at very low concentrations. Alternative and more efficient processes than ones usually employed are being intensively investigated as sorption. Biosorption of metals is already sufficiently known and its mechanisms have been intensely studied. Therefore, the efficiency and the mechanism of Cr(VI) ions uptake in chitosan magnetic particles obtained by suspension crosslinking technique were studied. These particles were spherical in shape and had a high porosity degree, a low saturation magnetization and a low percentage of swelling. The Cr(VI) ions uptake onto chitosan magnetic particles followed a mechanism of second order, suggesting chemical adsorption. (author)

  12. BIOSORPTION OF CHROMIUM (VI) USING IMMOBILIZED ...

    African Journals Online (AJOL)

    USER

    2016-05-20

    May 20, 2016 ... water and air. It affects the growth of flora and fauna which in turn affect human health negatively. Chromium could also bio-accumulate in plants and animals and this becomes ... The sorption kinetic models of Cr (VI) onto the biosorbents were examined with ... bulk density, moisture and ash contents.

  13. Simultaneous sorption of fluoride and arsenic ions (V) in a naturally occurring material modified with iron and aluminum; Sorcion simultanea de iones fluoruros y arsenico (V) en un material de origen natural modificado con hierro y aluminio

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez M, G.

    2016-07-01

    In this research, two materials, zeolite and pozzolans from the States of Oaxaca and Mexico, were used respectively, which were modified to evaluate their efficiencies to remove F and As(V) ions from solution and natural water. The materials were modified with iron and aluminum using an electrochemical cell, and with the hydroxides formed with iron and aluminum chloride solutions. The natural and modified materials were characterized by X-ray diffraction, scanning electron microscopy with energy X-ray disperse spectroscopy analysis, specific area and the point of zero charge (pHzpc). F- and As(V) adsorption properties of both materials were investigated. Experimental data on the sorption processes of F- ions by modified zeolite and pozzolans were adjusted to the kinetic models of pseudo-second-order (q e, 0408 mg /g K, 4.33 g / mg h) and Lagergen (q e, 0.807 mg/g K L, 1.83 1/min), respectively. Both materials showed the best fit to the Freundlich isotherm, Kf, 0.33 and 0.64 (mg/g) (L/mg) for pozzolans and zeolite respectively; suggesting a physical adsorption process on a heterogeneous material. Experimental adsorption capacities of pozzolans and modified zeolite for F ions were 0.36 and 0.83 mg/g respectively. The results of the kinetics of adsorption of As(V) were treated with the Largergren, pseudo-second-order and Elovich models; however the adsorption rate was high and consequently the rate constants could not be calculated. The isotherms data were fitted to the Freundlich model and the constants Kf were 6.24 and 11.15 (mg/g) (L/mg) for pozzolans and zeolite respectively. The thermodynamic parameters of the adsorption processes suggest endothermic adsorption for F- ions by both materials and for As(V) by the pozzolans. The free energy values ΔG indicate spontaneous processes and not spontaneous for F- ions by pozzolans. The adsorption of As (V) by the pozzolans presented an exothermic and spontaneous behavior. Finally, a study was performed in columns with

  14. Sorption of redox-sensitive elements: critical analysis

    Energy Technology Data Exchange (ETDEWEB)

    Strickert, R.G.

    1980-12-01

    The redox-sensitive elements (Tc, U, Np, Pu) discussed in this report are of interest to nuclear waste management due to their long-lived isotopes which have a potential radiotoxic effect on man. In their lower oxidation states these elements have been shown to be highly adsorbed by geologic materials occurring under reducing conditions. Experimental research conducted in recent years, especially through the Waste Isolation Safety Assessment Program (WISAP) and Waste/Rock Interaction Technology (WRIT) program, has provided extensive information on the mechanisms of retardation. In general, ion-exchange probably plays a minor role in the sorption behavior of cations of the above three actinide elements. Formation of anionic complexes of the oxidized states with common ligands (OH/sup -/, CO/sup - -//sub 3/) is expected to reduce adsorption by ion exchange further. Pertechnetate also exhibits little ion-exchange sorption by geologic media. In the reduced (IV) state, all of the elements are highly charged and it appears that they form a very insoluble compound (oxide, hydroxide, etc.) or undergo coprecipitation or are incorporated into minerals. The exact nature of the insoluble compounds and the effect of temperature, pH, pe, other chemical species, and other parameters are currently being investigated. Oxidation states other than Tc (IV,VII), U(IV,VI), Np(IV,V), and Pu(IV,V) are probably not important for the geologic repository environment expected, but should be considered especially when extreme conditions exist (radiation, temperature, etc.). Various experimental techniques such as oxidation-state analysis of tracer-level isotopes, redox potential measurement and control, pH measurement, and solid phase identification have been used to categorize the behavior of the various valence states.

  15. On the passivation mechanism of Fe{sub 3}O{sub 4} nanoparticles during Cr(VI) removal from water: A XAFS study

    Energy Technology Data Exchange (ETDEWEB)

    Pinakidou, F., E-mail: fpina@physics.auth.gr [Aristotle University of Thessaloniki, Department of Chemical Engineering, Analytical Chemistry Laboratory, 54124 Thessaloniki (Greece); Katsikini, M. [Aristotle University of Thessaloniki, School of Physics, Section of Solid State Physics, 54124 Thessaloniki (Greece); Simeonidis, K.; Kaprara, E. [Aristotle University of Thessaloniki, Department of Chemical Engineering, Analytical Chemistry Laboratory, 54124 Thessaloniki (Greece); Paloura, E.C. [Aristotle University of Thessaloniki, School of Physics, Section of Solid State Physics, 54124 Thessaloniki (Greece); Mitrakas, M. [Aristotle University of Thessaloniki, Department of Chemical Engineering, Analytical Chemistry Laboratory, 54124 Thessaloniki (Greece)

    2016-01-01

    Graphical abstract: - Highlights: • Presence of Fe(II) even after high Cr-loading. • The vacancies in the γ-Fe{sub 2}O{sub 3} layer formed offer sites for Cr(III) sorption. • Cr(III) sorbs into the vacancies and Cr(VI) forms outer sphere complexes. • Increasing surface Cr(III) loading changes the polymerization of the Fe–O–Fe chains. • Cr(III) sorption modifies Fe{sub 3}O{sub 4} structure obstructing further Cr(VI) removal. - Abstract: X-Ray Absorption Spectroscopies (XAFS) are employed in order to gather a thorough insight on the uptake mechanism of Cr(VI) by Fe{sub 3}O{sub 4} nanoparticles under water treatment conditions. The XANES measurements identify that the reducing potential of Fe{sub 3}O{sub 4} activates the precipitation of Cr(VI) in the form of insoluble and non-toxic Cr(III). However, electron donation from Fe(II) is responsible for its gradual consumption, resulting in the presence of a surface maghemite layer and the formation of structural vacancies. EXAFS analysis reveal that adsorption of Cr(III)-oxyanions occurs on sorption sites provided by the vacancies in the maghemite layer, where Cr(III) is involved in a bidentate binuclear ({sup 2}E) geometry with Fe-octahedra while it also forms monodentate ({sup 1}V) complexes with the Fe(III)O{sub 4} tetrahedra. The surface maghemitization along with the reduced Cr(III) adsorption into the vacancies, tracks the degree of Cr-reduction, since this surface structural modifications hinder Cr(VI) access to the Fe(II) ions of the magnetite nanoparticles. Thus, high surface coverage leads to the passivation of the reduction ability since physisorbed Cr(VI) is also detected through the formation of outer sphere complexes.

  16. Preparation, characterization, uranium (VI) biosorption models, and conditions optimization by response surface methodology (RSM) for amidoxime-functionalized marine fungus materials

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Xuechun; Gao, Yang; Jiang, Min; He, Dianxiong; Liao, Sen; Hou, Dan; Yan, Xueming; Long, Wei; Wu, Yaxin; Tan, Ni [Univ. of South China, Hengyang (China). School of Chemistry and Chemical Engineering

    2017-08-01

    Amidoxime-functionalized marine fungus Fusarium sp. ZZF51 (ZGDA) was synthesized and studied to adsorb uranium (VI) from the aqueous solution. Different instrumental techniques such as FTIR, SEM, and TGA were employed for the characterization of the manufactured materials, and theirs ability of removal uranium (VI) was optimized using RSM. The experimental results showed the maximum adsorption capacity for the synthesized materials was 230.78 mg g{sup -1} at the following optimization conditions: S-L ratio 150 mg L{sup -1}, pH 5.13, uranium (VI) initial concentration 40 mg L{sup -1}, and equilibrium time 122.40 min. More than 85% of the absorbed uranium (VI) could be desorbed by 0.5 or 1.0 mol L{sup -1} HCl, and the modified mycelium could be reused at least five times. The thermodynamic experimental data of adsorption uranium (VI) could fit better with Langmuir and Freundlich isotherms models, and the pseudo-second-order model was better to interpret the kinetics process. The modified fungus materials exhibited the better sorption capacity for uranium (VI) in comparison with raw biomass should be attributed to the strong chelation of amidoxime to uranium (VI) ions.

  17. Synthesis of layered titanate nanowires at low temperature and their application in efficient removal of U(VI).

    Science.gov (United States)

    Yin, Ling; Wang, Pengyi; Wen, Tao; Yu, Shujun; Wang, Xiangxue; Hayat, Tasawar; Alsaedi, Ahmed; Wang, Xiangke

    2017-07-01

    Uranium(VI) has become one of the most potential contaminants due to its productive and irreversibility impact on the surrounding environment. Titanate nanowires (TNWs) have attracted significant attention because of its high ion exchange ability and facile synthesis. Herein the TNWs were synthesized, and the morphology and structure of TNWs were investigated by Fourier transformed infrared spectroscopy, scanning electron microscope, transmission electron microscope, X-ray diffraction and X-ray photoelectron spectroscopy in detail. The application of TNWs in U(VI) removal was studied under various environmental conditions using batch technique, and the results indicated that the sorption of U(VI) on TNWs was strongly affected by pH and weakly affected by ionic strength. The presence of PO4(3-) and CO3(2-) could overwhelmingly influence U(VI) interaction with TNWs, which was mainly attributed to the formation of anionic and electro-neutral complexes. From the Langmuir model simulation, the maximum sorption capacities were calculated to be 358, 384, and 410 mg g(-1) at the temperatures of 298 K, 313 K and 328 K, respectively. The thermodynamic results revealed that the interaction process was spontaneous and endothermic. The extraordinary ion exchange capacity and facile synthesis under mild conditions made TNWs promising materials for the potential application in the efficient elimination of U(VI) or other lanthanides and actinides from aqueous solutions in the environmental radioactive pollution cleanup. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Performances of local chitosan and its nanocomposite 5%Bentonite/Chitosan in the removal of chromium ions (Cr(VI)) from wastewater.

    Science.gov (United States)

    Moussout, Hamou; Ahlafi, Hammou; Aazza, Mustapha; El Akili, Charaf

    2017-11-06

    The present work focuses on the study of the application of abundant and less expensive materials such as chitosan (CS) and bentonite/chitosan nanobiocomposite (nano 5%Bt/CS) in the removal of hexavalent chromium. The adsorption behavior of the prepared materials (CS and nano 5%Bt/CS) was tested for the removal of chromium (VI) ions in a synthetic solution and wastewater from a tanning industry. Spectroscopic analysis like techniques FTIR, XRD and SEM/EDX have been used to characterise the adsorbents before and after their contact with chromium ions. The experimental data indicate that the adsorption of chromium proceeds kinetically according to a pseudo-second order model on both adsorbents and the apparent activation energy (Ea) have been measured to be 4.11kJmol(-1) and 15.98kJmol(-1) for chitosan and nano 5%Bt/CS, respectively. It was found that the non-linear modelling of experimental isotherms was well adapted to the Langmuir and Redlich-Peterson models. Thermodynamic parameters (i.e., change in the free energy (ΔG°), the enthalpy (ΔH°), and the entropy (ΔS°)) have been also, evaluated and the results revealed that the removal of chromium ions on both solids was done via physical adsorption. The adsorption test on a real rejection of the tanning industry shows that the CS and nano 5%Bt/CS can substitute other more expensive adsorbents. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. A catechol-like phenolic ligand-functionalized hydrothermal carbon: One-pot synthesis, characterization and sorption behavior toward uranium

    Energy Technology Data Exchange (ETDEWEB)

    Li, Bo; Ma, Lijian; Tian, Yin; Yang, Xiaodan; Li, Juan; Bai, Chiyao; Yang, Xiaoyu; Zhang, Shuang; Li, Shoujian, E-mail: sjli000616@scu.edu.cn; Jin, Yongdong, E-mail: jinyongdong@scu.edu.cn

    2014-04-01

    Highlights: • A new catechol-like ligand-functionalized hydrothermal carbon sorbent is synthesized. • A combination of bayberry tannin and glyoxal is firstly used as starting materials. • Simple, economically viable and environment-friendly synthesis method. • The sorbent exhibits high sorption capacity and distinct selectivity for uranium. - Abstract: We proposed a new approach for preparing an efficient uranium-selective solid phase extractant (HTC-btg) by choosing bayberry tannin as the main building block and especially glyoxal as crosslinking agent via a simple, economic, and green one-pot hydrothermal synthesis. The results of characterization and analysis show that after addition of glyoxal into only bayberry tannin-based hydrothermal reaction system, the as-synthesized HTC-btg displayed higher thermal stability, larger specific surface area and more than doubled surface phenolic hydroxyl groups. The sorption behavior of the sorbents toward uranium under various conditions was investigated in detail and the results indicated that the process is fast, endothermic, spontaneous, and pseudo-second-order chemisorption. The U(VI) sorption capacity reached up to 307.3 mg g{sup −1} under the current experimental conditions. The selective sorption in a specially designed multi-ion solution containing 12 co-existing cations over the range of pH 1.0–4.5 shown that the amount of uranium sorbed accounts for about 53% of the total sorption amount at pH 4.5 and distinctively about 85%, unreported so far to our knowledge, at pH 2.0. Finally, a possible mechanism involving interaction between uranyl ions and phenolic hydroxyl groups on HTC-btg was proposed.

  20. SORPTION OF Au(III BY Saccharomyces cerevisiae BIOMASS

    Directory of Open Access Journals (Sweden)

    Amaria Amaria

    2010-07-01

    Full Text Available Au(III sorption by S. cerevisiae biomass extracted from beer waste industry was investigated. Experimentally, the sorption was conducted in batch method. This research involved five steps: 1 identification the functional groups present in the S. cerevisiae biomass by infrared spectroscopic technique, 2 determination of optimum pH, 3 determination of the sorption capacity and energy, 4 determination of the sorption type by conducting desorption of sorbed Au(III using specific eluents having different desorption capacity such as H2O (van der Waals, KNO3 (ion exchange, HNO3 (hydrogen bond, and tiourea (coordination bond, 5 determination of effective eluents in Au(III desorption by partial desorption of sorbed Au(III using thiourea, NaCN and KI. The remaining Au(III concentrations in filtrate were analyzed using Atomic Absorption Spectrophotometer. The results showed that: 1 Functional groups of S. cerevisiae biomass that involved in the sorption processes were hydroxyl (-OH, carboxylate (-COO- and amine (-NH2, 2 maximum sorption was occurred at pH 4, equal to 98.19% of total sorption, 3 The sorption capacity of biomass was 133.33 mg/g (6.7682E-04 mol/g and was involved sorption energy 23.03 kJ mol-1, 4 Sorption type was dominated by coordination bond, 5 NaCN was effective eluent to strip Au(III close to 100%.   Keywords: sorption, desorption, S. cerevisiae biomass, Au(III

  1. Fate and transport of uranium (VI) in weathered saprolite.

    Science.gov (United States)

    Kim, Young-Jin; Brooks, Scott C; Zhang, Fan; Parker, Jack C; Moon, Ji-Won; Roh, Yul

    2015-01-01

    Batch and column experiments were conducted to investigate sorption and transport of uranium (U) in the presence of saprolite derived from interbedded shale, limestone, and sandstone sequences. Sorption kinetics were measured at two initial concentrations (C0; 1, 10 μM) and three soil:solution ratios (Rs/w; 0.005, 0.25, 2 kg/L) at pH 4.5 (pH of the saprolite). The rate of U loss from solution (μmole/L/h) increased with increasing Rs/w. Uranium sorption exhibited a fast phase with 80% sorption in the first eight hours for all C0 and Rs/w values and a slow phase during which the reaction slowly approached (pseudo)equilibrium over the next seven days. The pH-dependency of U sorption was apparent in pH sorption edges. U(VI) sorption increased over the pH range 4-6, then decreased sharply at pH > 7.5. U(VI) sorption edges were well described by a surface complexation model using calibrated parameters and the reaction network proposed by Waite et al. (1994). Sorption isotherms measured using the same Rs/w and pH values showed a solids concentration effect where U(VI) sorption capacity and affinity decreased with increasing solids concentration. This effect may have been due to either particle aggregation or competition between U(VI) and exchangeable cations for sorption sites. The surface complexation model with calibrated parameters was able to predict the general sorption behavior relatively well, but failed to reproduce solid concentration effects, implying the importance of appropriate design if batch experiments are to be utilized for dynamic systems. Transport of U(VI) through the packed column was significantly retarded. Transport simulations were conducted using the reactive transport model HydroGeoChem (HGC) v5.0 that incorporated the surface complexation reaction network used to model the batch data. Model parameters reported by Waite et al. (1994) provided a better prediction of U transport than optimized parameters derived from our sorption edges. The

  2. Contribution of extracellular polymeric substances from Shewanella sp. HRCR-1 biofilms to U(VI) immobilization.

    Science.gov (United States)

    Cao, Bin; Ahmed, Bulbul; Kennedy, David W; Wang, Zheming; Shi, Liang; Marshall, Matthew J; Fredrickson, Jim K; Isern, Nancy G; Majors, Paul D; Beyenal, Haluk

    2011-07-01

    The goal of this study was to quantify the contribution of extracellular polymeric substances (EPS) to U(VI) immobilization by Shewanella sp. HRCR-1. Through comparison of U(VI) immobilization using cells with bound EPS (bEPS) and cells with minimal EPS, we show that (i) bEPS from Shewanella sp. HRCR-1 biofilms contribute significantly to U(VI) immobilization, especially at low initial U(VI) concentrations, through both sorption and reduction; (ii) bEPS can be considered a functional extension of the cells for U(VI) immobilization and they likely play more important roles at lower initial U(VI) concentrations; and (iii) the U(VI) reduction efficiency is dependent upon the initial U(VI) concentration and decreases at lower concentrations. To quantify the relative contributions of sorption and reduction to U(VI) immobilization by EPS fractions, we isolated loosely associated EPS (laEPS) and bEPS from Shewanella sp. HRCR-1 biofilms grown in a hollow fiber membrane biofilm reactor and tested their reactivity with U(VI). We found that, when reduced, the isolated cell-free EPS fractions could reduce U(VI). Polysaccharides in the EPS likely contributed to U(VI) sorption and dominated the reactivity of laEPS, while redox active components (e.g., outer membrane c-type cytochromes), especially in bEPS, possibly facilitated U(VI) reduction.

  3. Selective and sensitive speciation analysis of Cr(VI) and Cr(III) in water samples by fiber optic-linear array detection spectrophotometry after ion pair based-surfactant assisted dispersive liquid-liquid microextraction.

    Science.gov (United States)

    Yousefi, Seyedeh Mahboobeh; Shemirani, Farzaneh

    2013-06-15

    A simple ion pair based-surfactant assisted dispersive liquid-liquid microextraction (IP-SA-DLLME) was evaluated for extraction and preconcentration of Cr(VI) and Cr(III) in aqueous samples. In this method, which was used for the first time for chromium speciation analysis, sodium dodecyl sulfate (SDS) was used as both ion-pairing and disperser agent. Cr(VI) ions were converted into their cationic complex with 1,5-diphenylcarbazide (DPC) and then extracted into 1-octanol dispersed in aqueous solution. Cr(III) ion also can be determined by this procedure after oxidation to Cr(VI). After extraction and phase separation, upper organic phase was transferred to a micro cell of a fiber optic-linear array detection spectrophotometry (FO-LADS). The effects of various parameters on the extraction recovery were investigated. Under the optimized conditions and preconcentration of 10 mL of sample, the enrichment factor of 159 and the detection limit of 0.05 μgL(-1) were obtained. Validation of the method was performed by spiking-recovery method and comparison of results with those obtained by ET-AAS method. Copyright © 2013 Elsevier B.V. All rights reserved.

  4. Aspects on the catalysis of lipase from porcine pancreas (type VI-s in aqueous media: development of ion-pairs

    Directory of Open Access Journals (Sweden)

    Marina Kokkinou

    2012-04-01

    Full Text Available This article reports a first contribution for the elucidation of catalytic mechanism of Lipase from porcine pancreas, type VI-s (PPL, in hydrolyzing an ester substrate in aqueous media. The conclusions were based on the pH-profiles of Michaelis-Menten parameters k cat/Km, k cat and Km, as well as on the absolute temperature profile of k cat/Km, obtained during the hydrolysis of p-nitrophenyl laurate by PPL. It was found that (a PPL performs catalysis by means of ion pairs formed either as Ser152-Ο-/His263-Im+H and/or Carbonyl-Ο-/His263-Im+H, (b the parameter k cat/Km equals to k1 and thus ES is formed and destroyed in the course of a series of consecutive reactions governed by the dynamic constant K S = k2/k1, and (c the hydrolysis of substrate is assisted by a hydrogen bond developed between deprotonated Asp176 and the positively charged imidazole of His263 across a pKa-value 3.85, necessary for efficient catalysis.

  5. Influence of Arsenic (III, Cadmium (II, Chromium (VI, Mercury (II, and Lead (II Ions on Human Triple Negative Breast Cancer (HCC1806 Cell Cytotoxicity and Cell Viability

    Directory of Open Access Journals (Sweden)

    Tsdale F. Mehari

    2017-01-01

    Full Text Available The hazardous consequences of heavy metal ions (HMIs on human health necessitate the immediate need to probe fundamentally the interactions and cytotoxic effects of HMIs on humans. This study investigated the influence of five toxic HMIs (arsenic (As (III, cadmium (Cd (II, chromium (Cr (VI, mercury (Hg (II, and lead (Pb (II on human TNBC (HCC 1806 cell viability using optical microscopy, trypan blue dye-exclusion assays, and flow cytometry. The TNBC cells were exposed to varying concentrations of HMIs for 24 and 48 hours. We evaluated the influence of the concentrations and duration of HMIs exposure on TNBC cell viability. Light microscopy, cell viability assays, revealed that after 48-hour treatment of TNBC cells with 1 x 10-5 M of As (III, Cd (II, Hg (II, Cr (IV, and Pb (II resulted in cell viabilities of 23%, 34%, 35%, 56%, 91% respectively, suggesting that As (III has the greatest cytotoxicity (77% cell death while Pb (II showed the least (9% cell death. Furthermore, flow cytometry revealed that while Pb (II, As (III and Cr (IV had significant increases in cell death, Hg (II caused a G1 arrest. Together, this study revealed that HMIs cause a differential cytotoxic effect on TNBC cells and suggest that they may have very different genotoxic targets and implications in their mutagenic potential.

  6. As(V)/Cr(VI) retention on un-amended and waste-amended soil samples: competitive experiments.

    Science.gov (United States)

    Rivas-Pérez, Ivana M; Conde-Cid, Manuel; Nóvoa-Muñoz, Juan Carlos; Arias-Estévez, Manuel; Fernández-Sanjurjo, María J; Álvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino

    2017-01-01

    Focusing on simultaneous arsenic and chromium pollution, we used batch-type experiments to study As(V)/Cr (VI) competitive sorption on soil samples, pyritic material, mussel shell, oak ash, pine bark and hemp waste, as well as on binary mixtures (50 % mussel shell and 50 % another material-oak ash, pine bark, or hemp waste), and on forest and vineyard soil samples and pyritic material amended with 48 t ha(-1) of mussel shell, oak ash, pine bark, or hemp waste. Equal As(V) and Cr(VI) concentrations (0 to 6 mmol L(-1)) were added to the individual materials, binary mixtures, and 48 t ha(-1) amended materials. The individual forest soil sample, pyritic material, and oak ash showed clearly higher As(V) sorption, whereas Cr(VI) sorption was higher on pine bark. Sorption was up to 50 % higher for As(V) than for Cr(VI) on the forest soil sample, oak ash, and pyritic material, while pine bark sorbed 95 % more Cr(VI). Regarding binary mixtures, the presence of mussel shell increased As(V) sorption on pine bark and Cr(VI) sorption on hemp waste. As regards the amendments, in the case of the forest soil sample, the amendments with oak ash and mussel shell increased As(V) sorption, while pine bark amendment increased Cr(VI) sorption; in the vineyard soil sample, the mussel shell amendment increased As(V) sorption; in the pyritic material, pine bark amendment increased Cr(VI) sorption. These results could be useful to appropriately manage the soils and individual or mixed by-products assayed when As(V) and Cr(VI) pollution occurs.

  7. Solid-Phase Extraction of Trace Amounts of Uranium(VI in Environmental Water Samples Using an Extractant-Impregnated Resin Followed by Detection with UV-Vis Spectrophotometry

    Directory of Open Access Journals (Sweden)

    Ahmad Hosseini-Bandegharaei

    2013-01-01

    Full Text Available A stable extractant-impregnated resin (EIR containing Chrome Azurol B was prepared using Amberlite XAD-2010 as a porous polymeric support. The new EIR was employed for trace separation and preconcentration of U(VI ion followed by spectrophotometric determination with the arsenazo III procedure. CAB/XAD-2010 exhibited excellent selectivity for U(VI ion over coexisting ions. Experimental parameters including pH, contact time, shaking speed, and ionic strength were investigated by batch extraction methods. Maximum sorption of U(VI ions occurred at pH 4.3–6.9. The capacity of EIR was found to be 0.632 mmol·g−1. Equilibrium was reached in 25 min and the loading half-time, t1/2, was less than 6 min. The equilibrium adsorption isotherm of U(VI was fitted with the Langmuir adsorption model. In addition, a column packed with CAB/XAD-2010 was used for column-mode separation and preconcentration of U(VI ion. For the optimization of the dynamic procedure, effects of sample volume, sample and eluent flow rate, eluent concentration, and its volume were investigated. The preconcentration factors for U(VI were found out to be 160. But, for convenience, a preconcentration factor of 150 was utilized for the column-mode preconcentration. The dynamic procedure gave a detection limit of 5.0×10-10 mol·L−1 (0.12 μg·L−1 for U(VI ion. The proposed dynamic method showed good performance in analyzing environmental water samples.

  8. Sorption and migration of radionuclides in geologic media

    Energy Technology Data Exchange (ETDEWEB)

    Erdal, B.R.; Daniels, W.R.; Hoffman, D.C.; Lawrence, F.O.; Wolfsberg, K.

    1978-12-31

    The interactions of a quartz monzonite, an argillite, an alluvium, and several tuffs with various radionuclides in selected phreatic waters have been studied. The sorption--desorption hehavior of Sr, Tc(VII), Cs, Ba, Ce, Eu, U(VI), Pu, and Am under ambient and 70{sup 0}C temperature conditions has been measured.

  9. Geometry VI

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 1; Issue 8. Geometry VI - Space-the Final Frontier. Kapil H Paranjape. Series Article Volume 1 Issue 8 August 1996 pp 28-33. Fulltext. Click here to view fulltext PDF. Permanent link: http://www.ias.ac.in/article/fulltext/reso/001/08/0028-0033 ...

  10. VI KA’

    DEFF Research Database (Denmark)

    Sprogøe, Jonas

    2012-01-01

    Artiklen handler om hvordan man kan bruge et spil til at udvikle og måle kompetencer. Artiklen diskuterer forskellige forståelser kompetencebegrebet og diskuterer hvordan Vi Ka'-spillet bidrager til at indfange den mere aktive forståelse af kompetence, som noget du gør i en bestemt kontekst....

  11. Contribution of Extracellular Polymeric Substances from Shewanella sp. HRCR-1 Biofilms to U(VI) Immobilization

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Bin; Ahmed, B.; Kennedy, David W.; Wang, Zheming; Shi, Liang; Marshall, Matthew J.; Fredrickson, Jim K.; Isern, Nancy G.; Majors, Paul D.; Beyenal, Haluk

    2011-06-05

    The goal of this study was to quantify the contribution of extracellular polymeric substances (EPS) in U(VI) immobilization by Shewanella sp. HRCR-1. Through comparison of U(VI) immobilization using cells with bound EPS (bEPS) and cells without EPS, we showed that i) bEPS from Shewanella sp. HRCR-1 biofilms contributed significantly to U(VI) immobilization, especially at low initial U(VI) concentrations, through both sorption and reduction; ii) bEPS could be considered as a functional extension of the cells for U(VI) immobilization and they likely play more important roles at initial U(VI) concentrations; and iii) U(VI) reduction efficiency was found to be dependent upon initial U(VI) concentration and the efficiency decreased at lower concentrations. To quantify relative contribution of sorption and reduction in U(VI) immobilization by EPS fractions, we isolated loosely associated EPS (laEPS) and bEPS from Shewanella sp. HRCR-1 biofilms grown in a hollow fiber membrane biofilm reactor and tested their reactivity with U(V). We found that, when in reduced form, the isolated cell-free EPS fractions could reduce U(VI). Polysaccharides in the EPS likely contributed to U(VI) sorption and dominated reactivity of laEPS while redox active components (e.g., outer membrane c-type cytochromes), especially in bEPS, might facilitate U(VI) reduction.

  12. Chromium Biosorption from Cr(VI) Aqueous Solutions by Cupressus lusitanica Bark: Kinetics, Equilibrium and Thermodynamic Studies.

    Science.gov (United States)

    Netzahuatl-Muñoz, Alma Rosa; Cristiani-Urbina, María del Carmen; Cristiani-Urbina, Eliseo

    2015-01-01

    The present study investigated the kinetics, equilibrium and thermodynamics of chromium (Cr) ion biosorption from Cr(VI) aqueous solutions by Cupressus lusitanica bark (CLB). CLB total Cr biosorption capacity strongly depended on operating variables such as initial Cr(VI) concentration and contact time: as these variables rose, total Cr biosorption capacity increased significantly. Total Cr biosorption rate also increased with rising solution temperature. The pseudo-second-order model described the total Cr biosorption kinetic data best. Langmuir´s model fitted the experimental equilibrium biosorption data of total Cr best and predicted a maximum total Cr biosorption capacity of 305.4 mg g(-1). Total Cr biosorption by CLB is an endothermic and non-spontaneous process as indicated by the thermodynamic parameters. Results from the present kinetic, equilibrium and thermodynamic studies suggest that CLB biosorbs Cr ions from Cr(VI) aqueous solutions predominantly by a chemical sorption phenomenon. Low cost, availability, renewable nature, and effective total Cr biosorption make CLB a highly attractive and efficient method to remediate Cr(VI)-contaminated water and wastewater.

  13. Chromium Biosorption from Cr(VI) Aqueous Solutions by Cupressus lusitanica Bark: Kinetics, Equilibrium and Thermodynamic Studies

    Science.gov (United States)

    Netzahuatl-Muñoz, Alma Rosa; Cristiani-Urbina, María del Carmen; Cristiani-Urbina, Eliseo

    2015-01-01

    The present study investigated the kinetics, equilibrium and thermodynamics of chromium (Cr) ion biosorption from Cr(VI) aqueous solutions by Cupressus lusitanica bark (CLB). CLB total Cr biosorption capacity strongly depended on operating variables such as initial Cr(VI) concentration and contact time: as these variables rose, total Cr biosorption capacity increased significantly. Total Cr biosorption rate also increased with rising solution temperature. The pseudo-second-order model described the total Cr biosorption kinetic data best. Langmuir´s model fitted the experimental equilibrium biosorption data of total Cr best and predicted a maximum total Cr biosorption capacity of 305.4 mg g-1. Total Cr biosorption by CLB is an endothermic and non-spontaneous process as indicated by the thermodynamic parameters. Results from the present kinetic, equilibrium and thermodynamic studies suggest that CLB biosorbs Cr ions from Cr(VI) aqueous solutions predominantly by a chemical sorption phenomenon. Low cost, availability, renewable nature, and effective total Cr biosorption make CLB a highly attractive and efficient method to remediate Cr(VI)-contaminated water and wastewater. PMID:26352933

  14. Mechanisms of optical orientation of an individual Mn2+ ion spin in a II–VI quantum dot

    Science.gov (United States)

    Smoleński, T.; Cywiński, Ł.; Kossacki, P.

    2018-02-01

    We provide a theoretical description of the optical orientation of a single Mn2+ ion spin under quasi-resonant excitation demonstrated experimentally by Goryca et al (2009 Phys. Rev. Lett. 103 087401). We build and analyze a hierarchy of models by starting with the simplest assumptions (transfer of perfectly spin-polarized excitons from Mn-free dot to the other dot containing a single Mn2+ spin, followed by radiative recombination) and subsequently adding more features, such as spin relaxation of electrons and holes. Particular attention is paid to the role of the influx of the dark excitons and the process of biexciton formation, which are shown to contribute significantly to the orientation process in the quasi-resonant excitation case. Analyzed scenarios show how multiple features of the excitonic complexes in magnetically-doped quantum dots, such as the values of exchange integrals, spin relaxation times, etc, lead to a plethora of optical orientation processes, characterized by distinct dependencies on light polarization and laser intensity, and occurring on distinct timescales. Comparison with experimental data shows that the correct description of the optical orientation mechanism requires taking into account Mn2+ spin-flip processes occurring not only when the exciton is already in the orbital ground state of the light-emitting dot, but also those that happen during the exciton transfer from high-energy states to the ground state. Inspired by the experimental results on energy relaxation of electrons and holes in nonmagnetic dots, we focus on the process of biexciton creation allowed by mutual spin-flip of an electron and the Mn2+ spin, and we show that by including it in the model, we obtain good qualitative and quantitative agreement with the experimental data on quasi-resonantly driven Mn2+ spin orientation.

  15. Base Catalytic Approach: A Promising Technique for the Activation of Biochar for Equilibrium Sorption Studies of Copper, Cu(II) Ions in Single Solute System.

    Science.gov (United States)

    Hamid, Sharifah Bee Abdul; Chowdhury, Zaira Zaman; Zain, Sharifuddin Mohammad

    2014-04-09

    This study examines the feasibility of catalytically pretreated biochar derived from the dried exocarp or fruit peel of mangostene with Group I alkali metal hydroxide (KOH). The pretreated char was activated in the presence of carbon dioxide gas flow at high temperature to upgrade its physiochemical properties for the removal of copper, Cu(II) cations in single solute system. The effect of three independent variables, including temperature, agitation time and concentration, on sorption performance were carried out. Reaction kinetics parameters were determined by using linear regression analysis of the pseudo first, pseudo second, Elovich and intra-particle diffusion models. The regression co-efficient, R² values were best for the pseudo second order kinetic model for all the concentration ranges under investigation. This implied that Cu(II) cations were adsorbed mainly by chemical interactions with the surface active sites of the activated biochar. Langmuir, Freundlich and Temkin isotherm models were used to interpret the equilibrium data at different temperature. Thermodynamic studies revealed that the sorption process was spontaneous and endothermic. The surface area of the activated sample was 367.10 m²/g, whereas before base activation, it was only 1.22 m²/g. The results elucidated that the base pretreatment was efficient enough to yield porous carbon with an enlarged surface area, which can successfully eliminate Cu(II) cations from waste water.

  16. Base Catalytic Approach: A Promising Technique for the Activation of Biochar for Equilibrium Sorption Studies of Copper, Cu(II Ions in Single Solute System

    Directory of Open Access Journals (Sweden)

    Sharifah Bee Abdul Hamid

    2014-04-01

    Full Text Available This study examines the feasibility of catalytically pretreated biochar derived from the dried exocarp or fruit peel of mangostene with Group I alkali metal hydroxide (KOH. The pretreated char was activated in the presence of carbon dioxide gas flow at high temperature to upgrade its physiochemical properties for the removal of copper, Cu(II cations in single solute system. The effect of three independent variables, including temperature, agitation time and concentration, on sorption performance were carried out. Reaction kinetics parameters were determined by using linear regression analysis of the pseudo first, pseudo second, Elovich and intra-particle diffusion models. The regression co-efficient, R2 values were best for the pseudo second order kinetic model for all the concentration ranges under investigation. This implied that Cu(II cations were adsorbed mainly by chemical interactions with the surface active sites of the activated biochar. Langmuir, Freundlich and Temkin isotherm models were used to interpret the equilibrium data at different temperature. Thermodynamic studies revealed that the sorption process was spontaneous and endothermic. The surface area of the activated sample was 367.10 m2/g, whereas before base activation, it was only 1.22 m2/g. The results elucidated that the base pretreatment was efficient enough to yield porous carbon with an enlarged surface area, which can successfully eliminate Cu(II cations from waste water.

  17. Base Catalytic Approach: A Promising Technique for the Activation of Biochar for Equilibrium Sorption Studies of Copper, Cu(II) Ions in Single Solute System

    Science.gov (United States)

    Hamid, Sharifah Bee Abdul; Chowdhury, Zaira Zaman; Zain, Sharifuddin Mohammad

    2014-01-01

    This study examines the feasibility of catalytically pretreated biochar derived from the dried exocarp or fruit peel of mangostene with Group I alkali metal hydroxide (KOH). The pretreated char was activated in the presence of carbon dioxide gas flow at high temperature to upgrade its physiochemical properties for the removal of copper, Cu(II) cations in single solute system. The effect of three independent variables, including temperature, agitation time and concentration, on sorption performance were carried out. Reaction kinetics parameters were determined by using linear regression analysis of the pseudo first, pseudo second, Elovich and intra-particle diffusion models. The regression co-efficient, R2 values were best for the pseudo second order kinetic model for all the concentration ranges under investigation. This implied that Cu(II) cations were adsorbed mainly by chemical interactions with the surface active sites of the activated biochar. Langmuir, Freundlich and Temkin isotherm models were used to interpret the equilibrium data at different temperature. Thermodynamic studies revealed that the sorption process was spontaneous and endothermic. The surface area of the activated sample was 367.10 m2/g, whereas before base activation, it was only 1.22 m2/g. The results elucidated that the base pretreatment was efficient enough to yield porous carbon with an enlarged surface area, which can successfully eliminate Cu(II) cations from waste water. PMID:28788595

  18. Packed-bed column biosorption of chromium(VI) and nickel(II) onto Fenton modified Hydrilla verticillata dried biomass.

    Science.gov (United States)

    Mishra, Ashutosh; Tripathi, Brahma Dutt; Rai, Ashwani Kumar

    2016-10-01

    The present study represents the first attempt to investigate the biosorption potential of Fenton modified Hydrilla verticillata dried biomass (FMB) in removing chromium(VI) and nickel(II) ions from wastewater using up-flow packed-bed column reactor. Effects of different packed-bed column parameters such as bed height, flow rate, influent metal ion concentration and particle size were examined. The outcome of the column experiments illustrated that highest bed height (25cm); lowest flow rate (10mLmin(-1)), lowest influent metal concentration (5mgL(-1)) and smallest particle size range (0.25-0.50mm) are favourable for biosorption. The maximum biosorption capacity of FMB for chromium(VI) and nickel(II) removal were estimated to be 89.32 and 87.18mgg(-1) respectively. The breakthrough curves were analyzed using Bed Depth Service Time (BDST) and Thomas models. The experimental results obtained agree to both the models. Column regeneration experiments were also carried out using 0.1M HNO3. Results revealed good reusability of FMB during ten cycles of sorption and desorption. Performance of FMB-packed column in treating secondary effluent was also tested under identical experimental conditions. Results demonstrated significant reduction in chromium(VI) and nickel(II) ions concentration after the biosorption process. Copyright © 2016 Elsevier Inc. All rights reserved.

  19. Sorption and binary exchange of nitrate, sulfate, and uranium on an anion-exchange resin.

    Science.gov (United States)

    Gu, Baohua; Ku, Yee-Kyoung; Jardine, Philip M

    2004-06-01

    Competitive ion-exchange reactions were studied on a strong-base anion-exchange resin to remove NO3- and uranium from a contaminated groundwater containing high levels of NO3- (approximately 140 mM), SO4(2-) (approximately 10 mM), and U(VI) (approximately 0.2 mM). Results indicate that although SO4(2-) carries divalent negative charges, it showed the least selectivity for sorption by the Purolite A-520E resin, which is functionalized with triethylamine exchange sites. Nitrate was the most strongly sorbed. Sorption selectivity followed the order of NO3- > Cl- > SO4(2-) under the experimental conditions. Nitrate competitively sorbed and displaced previously sorbed SO4(2-) in a column flow-through experiment and resulted in a high elution front of SO4(2-) in the effluent. Although the concentration of uranium in groundwater is orders of magnitude lower than that of NO3- or SO4(2-), it was found to be strongly sorbed by the anion-exchange resin. Because the most stable uranium species in oxic and suboxic environments is the UO2(2+) cation, its strong sorption by anion-exchange resins is hypothesized to be the result of the co-ion effect of NO3- by forming anionic UO2(NO3)3- complexes in the resin matrix. These observations point out a potential alternative remediation strategy that uses strong-base anion-exchange resins to remove uranium from this site-specific groundwater, which has a low pH and a relatively high NO3- concentration.

  20. Sorption of fibronectin to human root surfaces in vitro

    Energy Technology Data Exchange (ETDEWEB)

    Mendieta, C.; Caravana, C.; Fine, D.H. (Columbia Univ., New York, NY (USA))

    1990-05-01

    The purpose of this study was to determine the conditions that favor the sorption and retention of human plasma fibronectin to cementum. Rectangular root segments prepared from teeth extracted for orthodontic reasons were mounted on a capillary pipette and immersed in solutions of {sup 125}I fibronectin for assay of cementum sorption under various conditions. Kinetic studies showed sorption to be rapid, with 77% of the maximum fibronectin sorption occurring within 1 minute. Fibronectin sorption was reduced when added in conjunction with serum and was inhibited by monovalent ions (such as sodium), but enhanced in the presence of divalent cations (such as calcium). Exposure of cementum to serum partially blocked subsequent sorption of fibronectin, while cementum bound fibronectin was eluted by subsequent exposure to serum. Treatment of cementum with citric acid pH 1.1 (4 minutes) followed by 5% sodium hypochlorite (5 minutes) caused a significant increase in fibronectin sorption with maximum retention upon subsequent exposure to serum (P less than 0.05). Fibronectin sorption to cementum was: rapid, electrostatic in nature, competitive, reversible, Ca+(+)-facilitated, and maximized by prior treatment of the root with citric acid and sodium hypochlorite. It is concluded that sorption of fibronectin to cementum can be achieved for clinical gain; however, conditions of application can significantly influence both accumulation and subsequent release of root sorbed material.

  1. Sorption of curium by silica colloids: Effect of humic acid

    Energy Technology Data Exchange (ETDEWEB)

    Kar, Aishwarya Soumitra; Kumar, Sumit [Radiochemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Tomar, B.S., E-mail: bstomar@barc.gov.in [Radiochemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Manchanda, V.K. [Radiochemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India)

    2011-02-28

    Sorption of curium by silica colloids has been studied as a function of pH and ionic strength using {sup 244}Cm as a tracer. The sorption was found to increase with increasing pH and reach a saturation value of {approx}95% at pH beyond 5.3. The effect of humic acid on the sorption of {sup 244}Cm onto silica was studied by changing the order of addition of the metal ion and humic acid. In general, in the presence of humic acid (2 mg/L), the sorption increased at lower pH (<5) while it decreased in the pH range 6.5-8 and above pH 8, the sorption was found to increase again. As curium forms strong complex with humic acid, its presence results in the enhancement of curium sorption at lower pH. At higher pH the humic acid present in the solution competes with the surface sites for curium thus decreasing the sorption. The decrease in the Cm sorption in presence of humic acid was found to be less when humic acid was added after the addition of curium. Linear additive model qualitatively reproduced the profile of the Cm(III) sorption by silica in presence of humic acid at least in the lower pH region, however it failed to yield quantitative agreement with the experimental results. The results of the present study evidenced the incorporation of Cm into the silica matrix.

  2. Mucopolysaccharidosis VI

    Science.gov (United States)

    2010-01-01

    Mucopolysaccharidosis VI (MPS VI) is a lysosomal storage disease with progressive multisystem involvement, associated with a deficiency of arylsulfatase B leading to the accumulation of dermatan sulfate. Birth prevalence is between 1 in 43,261 and 1 in 1,505,160 live births. The disorder shows a wide spectrum of symptoms from slowly to rapidly progressing forms. The characteristic skeletal dysplasia includes short stature, dysostosis multiplex and degenerative joint disease. Rapidly progressing forms may have onset from birth, elevated urinary glycosaminoglycans (generally >100 μg/mg creatinine), severe dysostosis multiplex, short stature, and death before the 2nd or 3rd decades. A more slowly progressing form has been described as having later onset, mildly elevated glycosaminoglycans (generally sialidosis and mucolipidosis. Before enzyme replacement therapy (ERT) with galsulfase (Naglazyme®), clinical management was limited to supportive care and hematopoietic stem cell transplantation. Galsulfase is now widely available and is a specific therapy providing improved endurance with an acceptable safety profile. Prognosis is variable depending on the age of onset, rate of disease progression, age at initiation of ERT and on the quality of the medical care provided. PMID:20385007

  3. Mucopolysaccharidosis VI

    Directory of Open Access Journals (Sweden)

    Harmatz Paul

    2010-04-01

    Full Text Available Abstract Mucopolysaccharidosis VI (MPS VI is a lysosomal storage disease with progressive multisystem involvement, associated with a deficiency of arylsulfatase B leading to the accumulation of dermatan sulfate. Birth prevalence is between 1 in 43,261 and 1 in 1,505,160 live births. The disorder shows a wide spectrum of symptoms from slowly to rapidly progressing forms. The characteristic skeletal dysplasia includes short stature, dysostosis multiplex and degenerative joint disease. Rapidly progressing forms may have onset from birth, elevated urinary glycosaminoglycans (generally >100 μg/mg creatinine, severe dysostosis multiplex, short stature, and death before the 2nd or 3rd decades. A more slowly progressing form has been described as having later onset, mildly elevated glycosaminoglycans (generally ARSB gene, located in chromosome 5 (5q13-5q14. Over 130 ARSB mutations have been reported, causing absent or reduced arylsulfatase B (N-acetylgalactosamine 4-sulfatase activity and interrupted dermatan sulfate and chondroitin sulfate degradation. Diagnosis generally requires evidence of clinical phenotype, arylsulfatase B enzyme activity ®, clinical management was limited to supportive care and hematopoietic stem cell transplantation. Galsulfase is now widely available and is a specific therapy providing improved endurance with an acceptable safety profile. Prognosis is variable depending on the age of onset, rate of disease progression, age at initiation of ERT and on the quality of the medical care provided.

  4. Influence of the redox state on the neptunium sorption under alkaline conditions. Batch sorption studies on titanium dioxide and calcium silicate hydrates

    Energy Technology Data Exchange (ETDEWEB)

    Tits, Jan; Laube, Andreas; Wieland, Erich [Paul Scherrer Institute (PSI), Villigen (Switzerland). Lab. for Waste Management; Gaona, Xavier [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany). Inst. for Nuclear Waste Disposal

    2014-07-01

    Wet chemistry experiments were carried out to investigate the effect of the redox state and aqueous speciation on the uptake of neptunium by titanium dioxide (TiO{sub 2}) and by calcium silicate hydrates (C-S-H) under alkaline conditions. TiO{sub 2} was chosen as a reference sorbent to determine the surface complexation behaviour of neptunium under alkaline conditions. C-S-H phases are important constituents of cement and concrete. They may contribute significantly to radionuclide retention due to their high recrystallization rates making incorporation the dominating sorption mechanism for many radionuclides (e.g. the actinides) on these materials. The sorption of neptunium on both solids was found to depend strongly on the degree of hydrolysis. On TiO{sub 2}R{sub d} values for Np(IV), Np(V) and Np(VI) are identical at pH = 10 and decrease with progressing hydrolysis in case of Np(V) and Np(VI). On C-S-H phases, R{sub d} values for the three redox states are also identical at pH = 10. While the R{sub d} values for Np(VI) sorption on C-S-H phases decrease with progressing hydrolysis, the R{sub d} values for Np(IV) and Np(V) sorption are not affected by the pH. In addition to the effect of hydrolysis, the presence of Ca is found to promote Np(V) and Np(VI) sorption on TiO{sub 2} whereas on C-S-H phases, the present wet chemistry data do not give unambiguous evidence. Thus, the aqueous speciation appears to have a similar influence on the sorption of the actinides on both types of solids despite the different sorption mechanism. The similar R{sub d} values for Np(IV,V,VI) sorption at pH = 10 can be explained qualitatively by invoking inter-ligand electrostatic repulsion between OH groups in the coordination sphere of Np(V) and Np(VI). This mechanism was proposed earlier in the literature for the prediction of actinide complexation constants with inorganic ligands. A limiting coordination number for each Np redox state, resulting from the inter-ligand electrostatic

  5. Sorption mechanisms of chromate with coprecipitated ferrihydrite in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Mamun, Abdullah Al, E-mail: mamun@toki.waseda.jp [Graduate School of Creative Science and Engineering, Waseda University, 3-4-1 Okubo, Shinjuku-ku, Tokyo 169-8555 (Japan); Morita, Masao, E-mail: masao.swimer@akane.waseda.jp [Graduate School of Creative Science and Engineering, Waseda University, 3-4-1 Okubo, Shinjuku-ku, Tokyo 169-8555 (Japan); Matsuoka, Mitsuaki, E-mail: m-matsuoka@aoni.waseda.jp [Faculty of Science and Engineering, Waseda University, 3-4-1 Okubo, Shinjuku-ku, Tokyo 169-8555 (Japan); Tokoro, Chiharu, E-mail: tokoro@waseda.jp [Faculty of Science and Engineering, Waseda University, 3-4-1 Okubo, Shinjuku-ku, Tokyo 169-8555 (Japan)

    2017-07-15

    Highlights: • Coprecipitation showed twice the sorption density of simple adsorption at pH 5. • Mechanism shift from outer- to inner-sphere surface complexation at high Cr/Fe. • In coprecipitation the mechanism shift occurs at lower Cr/Fe ratios than adsorption. • Higher-molar-ratio bidentate binuclear Cr−Fe bonds; yielded ferrihydrite expansion. - Abstract: Hexavalent chromium (Cr(VI)) attracted researchers’ interest for its toxicity, natural availability and removal difficulty. Nevertheless, its sorption mechanism is not clearly understood yet. In this work, we elucidated the sorption mechanism of the co-precipitation of chromates with ferrihydrite through quantitative analysis. The influence of Cr/Fe molar ratio on sorption was investigated by zeta potential measurements, X-ray diffraction (XRD) and X-ray adsorption fine-structure analysis (XAFS). Coprecipitation at pH 5 showed almost twice the sorption density of adsorption at pH 5. In co-precipitation, a shift of the XRD peak due to inner-sphere sorption of chromate was observed at Cr/Fe molar ratio 0.5. For adsorption, the same peak shift was confirmed at Cr/Fe molar ratio of 1. Zeta potential at pH 5 suggested that the sorption mechanism changed at Cr/Fe molar ratio 0.25 for coprecipitation and at Cr/Fe molar ratio of 1 for adsorption. Fitting of Cr and Fe K-edge extended X-ray adsorption fine-structure suggested that ferrihydrite immobilized Cr(VI) via outer sphere surface complexation for lower Cr/Fe ratios and via inner-sphere surface complexation for higher molar ratios. At higher molar ratios, bidentate binuclear Cr−Fe bonds were well established, thus resulting in the expansion of the ferrihydrite structure.

  6. Adsorption of chromium(VI) from aqueous solutions by glycidylmethacrylate-grafted-densified cellulose with quaternary ammonium groups

    Science.gov (United States)

    Anirudhan, T. S.; Nima, J.; Divya, P. L.

    2013-08-01

    This study successfully synthesized a new adsorbent by ethylation of glycidylmethacrylate grafted aminated titanium dioxide densified cellulose (Et-AMPGDC), to remove chromium(VI) from aqueous solutions. The adsorbent was characterized by the FTIR, XRD, SEM and TG-DTG measurements. Batch adsorption technique using Et-AMPGDC was applied for the removal of Cr(VI) from aqueous solution and waste water. The contact time necessary to attain equilibrium and the optimum pH were found to be 1 h and 4.5, respectively. The kinetics of sorption of Cr(VI) ions was described by a pseudo-second-order kinetic model. The equilibrium isotherm data were analyzed using the Langmuir and Freundlich isotherm equations and the adsorption process was reflected by Langmuir isotherm. The maximum adsorption capacity was evaluated to be 123.60 mg/g. The electroplating industrial wastewater samples were treated with Et-AMPGDC to demonstrate its efficiency in removing Cr(VI) from wastewater. Almost complete removal was possible with 100 mg of the adsorbent from 50 mL of wastewater sample. Desorption efficiency was achieved by treatment with 0.1 M NaOH and five adsorption-desorption cycles were performed without significant decrease in adsorption capacity.

  7. Concurrent Co2+ and Sr2+ sorption from binary mixtures using aluminum industry waste: Kinetic study

    Science.gov (United States)

    Milenković, A.; Smičiklas, I.; Šljivić-Ivanović, M.; Vukelić, N.

    2015-12-01

    Multi-component sorption studies are essential to identify the applicability of red mud as a lowcost sorbent for the simultaneous removal of metal ions from wastewaters. Sorption kinetics of Co2+ and Sr2+ ions was investigated, at different total concentrations of mixtures and different molar ratios of two cations. Kinetics of metal sorption from binary systems was found to be well described by pseudo-second order rate model. Equilibrium sorbed amounts and equilibrium times for Co2+ sorption increased with the increase of its total concentration in the mixture, whereas pseudo-second order rate constants exhibited the opposite trend. Sr2+ sorption was strongly suppressed in the presence of Co2+ ions, and the removal efficiency decreased with increasing concentration and mole fraction of Co2+. Red mud can be used for simultaneous Co2+ and Sr2+ removal from mixtures of lower initial concentration, otherwise Co2+ sorption is dominant.

  8. The ternary system U(VI) / humic acid / Opalinus Clay

    Energy Technology Data Exchange (ETDEWEB)

    Joseph, Claudia

    2013-07-23

    , where the geochemical interaction with uranium contaminated water plays a role. Concerning the suitability of Opalinus Clay as host rock for a nuclear waste repository, it can be concluded, that Opalinus Clay has a relatively high retardation potential for U(VI). In case of water ingress U(VI) as part of the nuclear waste is released into the clay formation. Under near-neutral pH conditions, it will be complexed by calcium and carbonate ions leached out from Opalinus Clay, whereby Ca{sub 2}UO{sub 2}(CO{sub 3}){sub 3}(aq) is formed. This complex is only weakly retarded by sorption onto the clay, which can contribute to an enhanced mobility of U(VI) in the host rock. However, the U(VI) migration through the clay rock is governed by molecular diffusion. This decelerates the migration of Ca{sub 2}UO{sub 2}(CO{sub 3}){sub 3}(aq) through Opalinus Clay and thus it represents the decisive retardation process in the investigated system.

  9. The application of macroporous copolymers in the sorption of heavy and precious metals from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Nastasović Aleksandra B.

    2006-01-01

    Full Text Available Macroporous crosslinked poly(GMA-co-EGDMA was synthesized by the suspension copolymerisation and functionalized by the ring-opening reaction of the pendant epoxy groups with ethylene diamine. The porosity parameters (specific pore volume, specific surface area, and pore diameter, which corresponds to half of the pore volume for the initial and amino-functionalized copolymer samples were calculated from the cumulative pore volume distribution curves obtained by mercury porosimetry. The selectivity, sorption capacity and sorption rate of amino-functionalized poly(GMA-co-EGDMA-en were determined under static conditions. The sorption of Cu(ll and Ag(l ions on poly(GMA-co-EGDMA-en was very rapid (ti/2 value about 1 min. Slower sorption was observed for Au(lll ions with a ti/2 value of 6.5 minutes. The different rates of Au(lll, Cu(ll and Ag(l sorption could be applied for gold, copper and silver ion separation from mixed solutions. The sorption of Ni(ll and Cu(ll ions from galvanic solution under competitive conditions was also fast, with ti/2 values of 0.5 and 2 min, respectively. However, Zn(ll sorption was considerably slower (a ti/2 of 10 min. Similar results were obtained for galvanic solution under dynamic conditions, i.e., the metal sorption capacities of poly(GMA-co-EGDMA-en decreased in the order: Ni(ll > Cu(ll >> Zn(ll. The reusability of amino-functionalized poly(GMA-co-EGDMA for Cu(ll sorption was tested in four sorption/desorption cycles. Regeneration experiments were performed with 0.1 and 1 M H2SO4 showed a Cu(ll capacity loss of 50 % in the first sorption/desorption cycle. The sorption capacity increased when additional neutralization with 0.1 and 1 M NaOH was performed after each sorption/desorption cycle.

  10. Lanthanide-Potassium Biphenyl-3,3'-disulfonyl-4,4'-dicarboxylate Frameworks: Gas Sorption, Proton Conductivity, and Luminescent Sensing of Metal Ions.

    Science.gov (United States)

    Zhou, Li-Juan; Deng, Wei-Hua; Wang, Yu-Ling; Xu, Gang; Yin, Shun-Gao; Liu, Qing-Yan

    2016-06-20

    A novel sulfonate-carboxylate ligand of biphenyl-3,3'-disulfonyl-4,4'-dicarboxylic acid (H4-BPDSDC) and its lanthanide-organic frameworks {[LnK(BPDSDC)(DMF)(H2O)]·x(solvent)}n (JXNU-2, where JXNU denotes Jiangxi Normal University, DMF indicates dimethylformamide, and Ln = Sm(3+), Eu(3+), and Pr(3+)) were synthesized and structurally characterized. The three isomorphous lanthanide compounds feature three-dimensional frameworks constructed from one-dimensional (1D) rod-shaped heterometallic Ln-K secondary building units and are an illustration of a Kagome-like lattice with large 1D hexagonal channels and small 1D trigonal channels. The porous material of the representive JXNU-2(Sm) has an affinity to quadrupolar molecules such as CO2 and C2H2. In addition, the JXNU-2(Sm) compound exhibits humidity- and temperature-dependent proton conductivity with a large value of 1.11 × 10(-3) S cm(-1) at 80 °C and 98% relative humidity. The hydrophilic sulfonate group on the surface of channels facilitates enrichment of the solvate water molecules in the channels, which enhances the proton conductivity of this material. Moreover, the JXNU-2(Eu) material with the characteristic bright red color shows the potential for recognition of K(+) and Fe(3+) ions. The enhancing Eu(3+) luminescence with the K(+) ion and quenching Eu(3+) luminescence with the Fe(3+) ion can be associated with the functional groups of the organic ligand.

  11. The removal of toxic metals from liquid effluents by ion exchange resins. Part I: Chromium(VI/Sulphate/Dowex 1x8

    Directory of Open Access Journals (Sweden)

    Alguacil, F. J.

    2002-08-01

    Full Text Available The removal of chromium (VI from sulphuric acid solutions using the Dowex 1x8 resin has been investigated. The influence of several variables such as the stirring speed, temperature, the sulphuric acid and metal concentrations in the aqueous phase and the variation of the amount of resin added has been studied. Various aqueous solutions were used for the elution of the metal. Although concentrated nitric acid elutes chromium, this can be best accomplished using hydrazine sulphate solutions which at the same time reduce the toxic Cr (VI to the less toxic trivalent chromium state. Results obtained from batch experiments were applied to a continuous system using vertical columns. Moreover, an analytical application of the system in the determination of Cr (VI presents in the leachate of an EAF dust was investigated by transfering the methodology to an on-line flow injection system.

    Se estudia la eliminación de cromo(VI presente en disoluciones de ácido sulfúrico mediante la resina Dowex 1x8. Las variables experimentales estudiadas fueron: velocidad de agitación, temperatura, las concentraciones de metal y ácido sulfúrico en el medio acuoso y la cantidad de resina añadida. Se utilizaron diversas disoluciones acuosas para eluir al metal. Aunque el ácido nítrico se puede utilizar como eluyente, la operación de elución parece ser más eficiente cuando se emplean disoluciones de sulfato de hidracina que, al mismo tiempo, reduce el cromo(VI a cromo(III. Los resultados obtenidos en los ensayos en discontinuo se han experimentado en sistemas en continuo, utilizando mini-columnas. Por último, se ha aplicado el sistema a la determinación analítica del cromo(VI presente en los lixiviados de un polvo de horno de arco eléctrico, transfiriendo la tecnología a un sistema on-line con inyección de flujo.

  12. Temperature effect on the retention of U(VI) by SrTiO{sub 3}; Effet de la temperature sur la retention de U(VI) par SrTiO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Garcia Rosales, G

    2007-11-15

    The purpose of this research was the study of the interaction mechanisms between U(VI) ions and SrTiO{sub 3} surfaces versus pH and temperature: 25, 50, 75 and 90 C. Firstly, a physicochemical characterization was realized (DRX, MEB, FTIR) and the surface site density was determined. The potentiometric titration data were simulated, for each temperature, using the constant capacitance model and taking into account bath protonation of the {identical_to}Sr-OH surface sites and deprotonation of the {identical_to}Ti-OH ones (one pK{sub a} model). Both enthalpy and entropy changes, corresponding to the surface acid-base reactions, were evaluated using the van't Hoff relation. U(VI) was sorbed onto SrTiO{sub 3} powder in the pH range 0.5-5.0 with an U(VI) initial concentration 1.10{sup -4} M. By TRLIFS two U(VI) complexes were detected associated with two lifetime values (60 {+-} 5 and 12 {+-} 2 {mu}s at 25 C). The sorption edges were simulated using FITEQL 4.0 software. The surface complexation constants of the system SrTiO{sub 3}/U(VI) between 25 and 90 C temperature range were thus obtained with the constant capacitance model considering two reactive surface sites. It reveals that two types of surface complex, namely [({identical_to}SrOH)({identical_to}TiOH)UO{sub 2}]{sup 2+} and [({identical_to}TiOH)({identical_to}TiO)UO{sup 2+}]{sup 2+}, are needed to properly describe the experimental observations. By application of the van't Hoff equation, Delta{sub R}S{sup 0} and Delta{sub R}H{sup 0} were obtained, which indicated an endothermic sorption process. Finally, an energy transfer study was realised by TRLIFS. The energy transfer between Tb{sup 3+} and Eu{sup 3+} ions sorbed onto SrTiO{sub 3} powders were investigated. The results showed that the energy transfer between Tb{sup 3+} and Eu{sup 3+} is a non-radiative process and follows a dipole-dipole type interaction. A formalism based on the Dexter and the Inokuti-Hirayama theories was used to calculate the

  13. Sorption of Pb2+ Ions from Aqueous Solutions on Organic Wastes (part i) / Sorpcja JONÓW Pb2+ Z ROZTWORÓW Wodnych NA Odpadach Organicznych (CZĘŚĆ I)

    Science.gov (United States)

    Bożęcka, Agnieszka; Sanak-Rydlewska, Stanisława

    2013-12-01

    This article presents the results of the research on the Pb2+ ions sorption from model aqueous solutions on walnut shells, plum stones and sunflower hulls. The effect of various factors, such as the concentration of natural sorbent, the pH, and the temperature was studied. The process of Pb2+ ions sorption on studied sorbents was described by the Langmuir model. The best sorption capacity has been revealed for sunflower hulls. The maximum sorption capacity for this material was 36.9 mg/g. W artykule przedstawiono wyniki badań, które dotyczyły usuwania jonów Pb2+ z modelowych roztworów wodnych za pomocą odpadów organicznych, takich jak: łuski słonecznika, łupiny orzecha włoskiego i pestki śliwek. Dla badanego zakresu stężeń od 6,0-110 mg/dm3 i warunków procesu największą wydajność sorpcji, będącą w zakresie (89,4-96,3)% uzyskano dla łusek słonecznika. W przypadku łupin orzecha włoskiego i pestek śliwek sorpcja jonów Pb2+ jest znacznie niższa a jej wydajność wynosi odpowiednio (60,8-78,7)% i (62,3-81,3)%. Zbadano także wpływ stężenia sorbentu, pH roztworu i temperatury na badany proces sorpcji. Dla wszystkich materiałów optymalne stężenie sorbentu wyniosło 5 g/dm3. Powyżej tej wartości nie obserwowano istotnych zmian w stopniu redukcji jonów Pb2+ (rys.2). We wszystkich przypadkach maksima sorpcji osiągnięto przy pH równym 4,0±0,1 co obrazuje rysunek 3. Obniżenie sorpcji, występujące przy pH poniżej i powyżej wartości 4,0 prawdopodobnie związane jest to z ładunkiem gromadzącym się na powierzchni sorbentu (elektrostatyczne odpychanie i przyciąganie badanych jonów). Wartość pH roztworu determinuje także formę oraz stężenie badanego jonu w roztworze. W roztworach silnie kwaśnych ołów występuje głównie w postaci kationów. Stopniowy wzrost pH prowadzi do tworzenia jonów kompleksowych i strącania go w postaci wodorotlenku. Wykazano również, że ze wzrostem temperatury w zakresie (293-313)K nast

  14. Influence of humic acid on the Am(III) sorption onto kaolinite

    Energy Technology Data Exchange (ETDEWEB)

    Krepelova, A.; Sachs, S.; Bernhard, G. [Forschungszentrum Rossendorf e.V. (FZR), Dresden (Germany). Inst. fuer Radiochemie

    2011-07-01

    The sorption of americium(III), (Am(III)), onto kaolinite was studied in batch experiments in the absence and presence of humic acid (HA) ([Am(III)]{sub 0} = 1 x 10{sup -6} M, [HA]{sub 0} = 0 or 10 mg/L, I = 0.01 M NaClO{sub 4}, pH = 3-10, p{sub CO{sub 2}} = 10{sup -3.5} atm, solid-to-liquid ratio (S/L)=1 or 4 g/L). The results show that the Am(III) sorption onto kaolinite is influenced by S/L, the presence of HA and the pH value. In the absence of HA, Am(III) exhibits a very strong and almost pH independent sorption onto kaolinite at the S/L ratio of 4 g/L. In the presence of HA, there are small differences in the Am(III) sorption compared to the HA free system. At pH values < 5, HA very slightly enhances the sorption of Am(III). Conversely, at pH values {>=} 5.5, the presence of HA decreases the sorption of Am(III) due to the formation of dissolved Am(III) humate complexes. The decrease of S/L from 4 to 1 g/L has a significant effect on the Am(III) sorption onto kaolinite. A sorption edge occurs at pH 6 and the influence of carbonate on the Am(III) sorption at higher pH values becomes evident. Furthermore, the influence of HA on the Am(III) sorption onto kaolinite is more pronounced. The Am(III) sorption results are compared to literature data and to those of U(VI) sorption onto kaolinite obtained under the same experimental conditions. (orig.)

  15. Cesium sorption and desorption on selected Los Alamos soils

    Energy Technology Data Exchange (ETDEWEB)

    Kung, K.S.; Chan, J.; Longmire, P.; Fowler, M.

    1995-08-01

    Laboratory experiments were conducted to evaluate the sorptivity of cesium onto Los Alamos soils under controlled experimental conditions. Four soil profiles were collected and each soil profile which is broken into layers according to previously identified soil horizons were studied. Batch sorption isotherms were studied to quantify the chemical reactivity of each soil horizon toward cesium ion. Radioactive cesium-137 was used as sorbent and gamma counting was used to quantify the amount of sorption. Desorption experiments were conducted after the sorption experiments. Batch desorption isotherms were studied to quantify the desorption of presorbed cesium from these Los Alamos soils. This study suggests cesium may sorb strongly and irreversibly on most Los Alamos soils. The amount of cesium sorption and desorption is possibly related to the clay content of the soil sample since subsurface sample has a higher clay content than that of surface sample.

  16. Pyridine appended L-methionine: a novel chelating resin for pH dependent Cr speciation with scanning electron microscopic evidence and monitoring of yeast mediated green bio-reduction of Cr(VI) to Cr(III) in environmental samples.

    Science.gov (United States)

    Sahana, Animesh; Das, Sudipto; Banerjee, Arnab; Lohar, Sisir; Karak, Debasis; Das, Debasis

    2011-01-30

    Chemical speciation and pH dependent separation of Cr(III) and Cr(VI) species in environmental samples have been achieved by solid phase extraction using a new chelating resin containing pyridine appended L-methionine. Cr(III) is completely sorbed on the resin at pH 8.0 and Cr(VI) at pH 2.0. Hence a pH dependent separation of Cr(III) and Cr(VI) is possible with a limit of detection of 1.6 μg mL(-1) and 0.6 μg mL(-1) respectively. The sorption capacity of the resin for Cr(III) and Cr(VI) is 2.8 mmol g(-1) and 1.3 mmol g(-1) respectively. The sorption of chromium on the resin is supported by scanning electron microscopy (SEM). Complete desorption of Cr(III) and Cr(VI) from 1g of Cr loaded resin was achieved using 10 mL of 2 mol L(-1) HNO(3) and 6 mL of 3 mol L(-1) HNO(3) respectively. Quantitative recoveries of Cr(III) (pH 8.0) and Cr(VI) (pH 2.0) were found to be 96.0% and 98.0% respectively. Reduction efficiency of Rhodotornula mucilaginosa yeast from Cr(VI) to Cr(III) was monitored with this new resin. Concentrations of metal ions were measured by flame atomic absorption spectroscopy (FAAS). Copyright © 2010 Elsevier B.V. All rights reserved.

  17. Factors influencing U(VI adsorption onto soil from a candidate very low level radioactive waste disposal site in China

    Directory of Open Access Journals (Sweden)

    Zuo Rui

    2016-01-01

    Full Text Available The properties of soil at disposal sites are very important for geological disposal of very low level radioactive waste in terms of U(VI. In this study, soil from a candidate very low level radioactive waste disposal site in China was evaluated for its capacity on uranium sorption. Specifically, the equilibrium time, initial concentration, soil particle, pH, temperature, and carbonate were evaluated. The results indicated that after 15-20 days of sorption, the Kd value fluctuated and stabilized at 355-360 mL/g. The adsorptive capacity of uranium was increased as the initial uranium concentration increased, while it decreased as the soil particle size increased. The pH value played an important role in the U(VI sorption onto soil, especially under alkaline conditions, and had a great effect on the sorption capacity of soil for uranium. Moreover, the presence of carbonate decreased the sorption of U(VI onto soil because of the role of the strong complexation of carbonate with U(VI in the groundwater. Overall, this study assessed the behavior of U(VI sorption onto natural soil, which would be an important factor in the geological barrier of the repository, has contribution on mastering the characteristic of the adsorption of uranium in the particular soil media for the process of very low level radioactive waste disposal.

  18. Nickel and cobalt sorption on anaerobic granular sludges: kinetic and equilibrium studies

    NARCIS (Netherlands)

    Hullebusch, van E.D.; Zandvoort, M.H.; Lens, P.N.L.

    2004-01-01

    The kinetics and equilibria of sorption of the divalent metal ions cobalt and nickel onto anaerobic granular sludge are described. Single component and binary equimolar systems were studied at different pH values (pH 6, 7 and 8). The kinetic modelling of metal sorption by anaerobic granular sludge

  19. Cranial mononeuropathy VI

    Science.gov (United States)

    ... Abducens palsy; Lateral rectus palsy; VIth nerve palsy; Cranial nerve VI palsy; Sixth nerve palsy; Neuropathy - sixth nerve ... Cranial mononeuropathy VI is damage to the sixth cranial nerve. This nerve is also called the abducens nerve. ...

  20. Metal Ions Removal Using Nano Oxide Pyrolox™ Material

    Science.gov (United States)

    Gładysz-Płaska, A.; Skwarek, E.; Budnyak, T. M.; Kołodyńska, D.

    2017-02-01

    The paper presents the use of Pyrolox™ containing manganese nano oxides used for the removal of Cu(II), Zn(II), Cd(II), and Pb(II) as well as U(VI) ions. Their concentrations were analyzed using the atomic absorption spectrometer SpectrAA 240 FS (Varian) as well as UV-vis method. For this purpose the static kinetic and equilibrium studies were carried out using the batch technique. The effect of solution pH, shaking time, initial metal ion concentrations, sorbent dosage, and temperature was investigated. The equilibrium data were analyzed using the sorption isotherm models proposed by Freundlich, Langmuir-Freundlich, Temkin, and Dubinin-Radushkevich. The kinetic results showed that the pseudo second order kinetic model was found to correlate the experimental data well. The results indicate that adsorption of Cu(II), Zn(II), Cd(II), and Pb(II) as well as U(VI) ions is strongly dependent on pH. The value of pH 4-7 was optimal adsorption. The time to reach the equilibrium was found to be 24 h, and after this time, the sorption percentage reached about 70%. Kinetics of Cu(II), Zn(II), Cd(II), Pb(II), and U(VI) adsorption on the adsorbent can be described by the pseudo second order rate equation. Nitrogen adsorption/desorption, infrared spectroscopy (FTIR), and scanning electron microscopy (SEM) measurements for adsorbent characterization were performed. Characteristic points of the double layer determined for the studied Pyrolox™ sample in 0.001 mol/dm3 NaCl solution are pHPZC = 4 and pHIEP < 2.

  1. Studies on the effect of pH on the sorption of cadmium (ll), nickel (II ...

    African Journals Online (AJOL)

    Studies on the effect of pH on the sorption of cadmium (ll), nickel (II), lead (II) and chromium (VI) from aqueous solutions by African white star apple ( Chrysophyllum albidium ) shell. ... The cleaning of our environment should be carried out with the use of natural products instead of chemicals so as to reduce pollution.

  2. Sorption of actinides onto nanodiamonds

    Energy Technology Data Exchange (ETDEWEB)

    Buchatskaya, Yulia; Romanchuk, Anna; Yakovlev, Ruslan; Kulakova, Inna [Lomonosov Moscow State Univ., Moscow (Russian Federation). Dept. of Chemistry; Shiryaev, Andrei [Russian Academy of Sciences, Moscow (Russian Federation). Frumkin Institute of Physical Chemistry and Electrochemistry; Russian Academy of Sciences, Moscow (Russian Federation). Inst. of Geology of Ore Deposits, Petrography, Mineralogy and Geochemistry; Kalmykov, Stepan [Lomonosov Moscow State Univ., Moscow (Russian Federation). Dept. of Chemistry; Russian Academy of Sciences, Moscow (Russian Federation). Frumkin Institute of Physical Chemistry and Electrochemistry; Russian Academy of Sciences, Moscow (Russian Federation). Vernadsky Institute of Geochemistry and Analytical Chemistry

    2015-06-01

    Detonation nanodiamonds (ND) present a significant part of nanocarbons group, which could be produced on commercial scale by detonation of explosives in a closed chamber. Their unique properties of high surface area, low weight and radiation resistance make ND a prospective candidate for applications in sorption processes in radiochemistry. To study the influence of surface chemistry on sorption properties, apristine sample of ND was treated with acids and hydrogen. The surface chemistry of the samples was characterised by infrared spectroscopy, X-ray photoelectron spectroscopy and Boehm titration. The sorption properties of ND were tested fordifferent radionuclides. The sorption capacity of ND was shown to be higher than those of commonly used radionuclide sorbents like activated carbon and compariable to other members of nanocarbon group like graphene oxide and carbon nanotubes. The sorption properties were shown to be influenced by the presence of oxygen-containing groups on the surface of ND. This represents an opportunity to increase the sorption capacity of ND.

  3. Water sorption of resin-modified glass-ionomer cements photoactivated with LED Sorção de água de cimentos de ionômero de vidro modificados por resina fotoativados com LED

    Directory of Open Access Journals (Sweden)

    Daniela Francisca Gigo Cefaly

    2006-12-01

    Full Text Available The Light Emitting Diodes (LED technology has been used to photoactivate composite resins and there is a great number of published studies in this area. However, there are no studies regarding resin-modified glass-ionomer cements (RMGIC, which also need photoactivation. Therefore, the aim of this study was to evaluate water sorption of two RMGIC photoactivated with LED and to compare this property to that obtained with a halogen light curing unit. A resin composite was used as control. Five specimens of 15.0 mm in diameter x 1.0 mm in height were prepared for each combination of material (Fuji II LC Improved, Vitremer, and Filtek Z250 and curing unit (Radii and Optilight Plus and transferred to desiccators until a constant mass was obtained. Then the specimens were immersed into deionized water for 7 days, weighed and reconditioned to a constant mass in desiccators. Water sorption was calculated based on weight and volume of specimens. The data were analyzed by two-way ANOVA and Tukey test (p A tecnologia baseada em Diodos emissores de luz (LED tem sido utilizada para a fotoativação de resinas compostas e existe um grande número de estudos publicados a este respeito. Entretanto, não existem estudos envolvendo cimentos de ionômero de vidro modificados por resina (CIVMR, que também necessitam fotoativação. Assim, o objetivo deste estudo foi o de avaliar a sorção de água de dois CIVMR fotoativados com LED e comparar essa propriedade com aquela obtida com unidade com lâmpada halógena. Uma resina composta foi utilizada como controle. Cinco espécimes com 15,0 mm diâmetro x 1,0 mm de altura foram preparados para cada combinação de material (Fuji II LC Improved, Vitremer e Filtek Z250 e fonte de luz (Radii e Optilight Plus e transferidos a dessecadores até a obtenção de massa constante. Em seguida, os espécimes foram imersos em água deionizada por 7 dias, pesados e recondicionados a uma massa constante em dessecadores. A sor

  4. KINETIC STUDIES ON THE SORPTION OF LEAD AND CADMIUM ...

    African Journals Online (AJOL)

    Kinetic investigations are necessary for determining the rate of reaction and mechanism. The kinetics of the sorption of Pb2+ and Cd2+ from aqueous solution on to the biomass of C. bicolor was studied by batch equilibrium technique. The removal of the two metal ions was found to be > 60% depending on the initial metal ...

  5. Ofloxacin sorption in soils after long-term tillage: The contribution of organic and mineral compositions

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Dandan; Chen, Bingfa; Wu, Min, E-mail: kustless@gmail.com; Liang, Ni; Zhang, Di; Li, Hao; Pan, Bo

    2014-11-01

    Intensive human activities in agricultural areas resulted in significant alteration of soil properties, which consequently change their interactions with various contaminants. This process needs to be incorporated in contaminant behavior prediction and their risk assessment. However, the relevant study is missing. This work was designed to examine the change of soil properties and ofloxacin (OFL) sorption after tillage. Soil samples were collected in Yuanyang, Mengzi, and Dianchi areas with different agricultural activities. Although the mineral compositions of soils from Yuanyang and Dianchi differed greatly, these compositions are similar after tillage, especially for paddy soils. Soil pH decreased generally after OFL sorption, suggesting that ion exchange of OFL with protons in soil organic matter (SOM) was important for OFL sorption. However, a positive relationship between SOM and OFL sorption was not observed. On the contrary, increased SOM decreased OFL sorption when soils from the same geological location were compared. Generally speaking, tillage activities or dense vegetations greatly decreased OFL sorption. The higher OFL sorption in B horizon than A horizon suggested limited leaching of OFL through soil columns. The summed sorption calculated based on the sorption of individual soil components and their percentages in soils was higher than the intact soil. This phenomenon may be understood from the interactions between soil components, such as the coating of SOM on mineral particles. This study emphasizes that soil should be treat as a dynamic environmental matrix when assessing antibiotic behaviors and risks, especially in the area with intense human activities. - Highlights: • Mineral compositions tend to be similar after tillage. • Increased SOM decreases OFL sorption for soils from the same geological location. • Tillage activities or dense vegetations greatly decrease OFL sorption. • The summed sorption of individual soil components is

  6. Speciation of arsenic(III)/arsenic(V) and selenium(IV)/ selenium(VI) using coupled ion chromatography - hydride generation atomic absorption spectrometry

    Science.gov (United States)

    Simple analytical methods have been developed to speciate inorganic arsenic and selenium in the ppb range using coupled ion chromatography-hydride generation atomic absorption spectrometry. Because of the differences in toxicity and adsorption behavior, determinations of the redox states arsenite A...

  7. Predicting chromium (VI) adsorption rate in the treatment of liquid ...

    African Journals Online (AJOL)

    The adsorption rate of chromium (VI) on commercial activated carbon during the treatment of the flocculation effluent of liquid-phase oil-based drill-cuttings has been investigated in terms of contact time and initial chromium (VI) ion concentration. Homogenizing 1 g of the activated carbon with 100 ml of the flocculation ...

  8. Effect of deacetylation on property of electrospun chitosan/PVA nanofibrous membrane and removal of methyl orange, Fe(III) and Cr(VI) ions.

    Science.gov (United States)

    Habiba, Umma; Siddique, Tawsif A; Talebian, Sepehr; Lee, Jacky Jia Li; Salleh, Areisman; Ang, Bee Chin; Afifi, Amalina M

    2017-12-01

    In this study, effect of degree of deacetylation on property and adsorption capacity of chitosan/polyvinyl Alcohol electrospun membrane has been investigated. Resulting nanofibers were characterized by FESEM, FTIR, XRD, TGA, tensile testing, weight loss test and adsorption test. FESEM result shows, finer nanofiber was fabricated from 42h hydrolyzed chitosan and PVA blend solution. FTIR and XRD result showed a strong interaction between chitosan and polyvinyl alcohol. Higher tensile strength was observed for the nanofiber having 42h hydrolyzed chitosan. Blend solution of chitosan/PVA having low DD chitosan had higher viscosity. The nanofibrous membrane was stable in distilled water, acidic and basic medium. The isotherm study shows that the adsorption capacity (qm) of nanofiber containing higher DD chitosan was higher for Cr(VI). In contrary, the membrane containing chitosan with lower DD showed the higher adsorption capacity for Fe(III) and methyl orange. Moreover, the effect of DD on removal percentage of adsorbate was dependent on the initial concentration of the adsorbate. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Scaling Effects of Cr(VI) Reduction Kinetics. The Role of Geochemical Heterogeneity

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Li [Pennsylvania State Univ., State College, PA (United States); Li, Li [Pennsylvania State Univ., State College, PA (United States)

    2015-10-22

    The natural subsurface is highly heterogeneous with minerals distributed in different spatial patterns. Fundamental understanding of how mineral spatial distribution patterns regulate sorption process is important for predicting the transport and fate of chemicals. Existing studies about the sorption was carried out in well-mixed batch reactors or uniformly packed columns, with few data available on the effects of spatial heterogeneities. As a result, there is a lack of data and understanding on how spatial heterogeneities control sorption processes. In this project, we aim to understand and develop modeling capabilities to predict the sorption of Cr(VI), an omnipresent contaminant in natural systems due to its natural occurrence and industrial utilization. We systematically examine the role of spatial patterns of illite, a common clay, in determining the extent of transport limitation and scaling effects associated with Cr(VI) sorption capacity and kinetics using column experiments and reactive transport modeling. Our results showed that the sorbed mass and rates can differ by an order of magnitude due to of the illite spatial heterogeneities and transport limitation. With constraints from data, we also developed the capabilities of modeling Cr(VI) in heterogeneous media. The developed model is then utilized to understand the general principles that govern the relationship between sorption and connectivity, a key measure of the spatial pattern characteristics. This correlation can be used to estimate Cr(VI) sorption characteristics in heterogeneous porous media. Insights gained here bridge gaps between laboratory and field application in hydrogeology and geochemical field, and advance predictive understanding of reactive transport processes in the natural heterogeneous subsurface. We believe that these findings will be of interest to a large number of environmental geochemists and engineers, hydrogeologists, and those interested in contaminant fate and transport

  10. Self-assembly of silver nanoparticles as high active surface-enhanced Raman scattering substrate for rapid and trace analysis of uranyl(VI) ions

    Science.gov (United States)

    Wang, Shaofei; Jiang, Jiaolai; Wu, Haoxi; Jia, Jianping; Shao, Lang; Tang, Hao; Ren, Yiming; Chu, Mingfu; Wang, Xiaolin

    2017-06-01

    A facile surface-enhanced Raman scattering (SERS) substrate based on the self-assembly of silver nanoparticles on the modified silicon wafer was obtained, and for the first time, an advanced SERS analysis method basing on this as-prepared substrate was established for high sensitive and rapid detection of uranyl ions. Due to the weakened bond strength of Odbnd Udbnd O resulting from two kinds of adsorption of uranyl species (;strong; and ;weak; adsorption) on the substrate, the ν1 symmetric stretch vibration frequency of Odbnd Udbnd O shifted from 871 cm- 1 (normal Raman) to 720 cm- 1 and 826 cm- 1 (SERS) along with significant Raman enhancement. Effects of the hydrolysis of uranyl ions on SERS were also investigated, and the SERS band at 826 cm- 1 was first used to approximately define the constitution of uranyl species at trace quantity level. Besides, the SERS intensity was proportional to the variable concentrations of uranyl nitrate ranging from 10- 7 to 10- 3 mol L- 1 with an excellent linear relation (R2 = 0.998), and the detection limit was 10- 7 mol L- 1. Furthermore, the related SERS approach involves low-cost substrate fabrication, rapid and trace analysis simultaneously, and shows great potential applications for the field assays of uranyl ions in the nuclear fuel cycle and environmental monitoring.

  11. Proposed adsorption-diffusion model for characterizing chromium(VI) removal using dried water hyacinth roots

    Energy Technology Data Exchange (ETDEWEB)

    Sarkar, Debasish; Mukherjee, Paramartha; Bandyopadhyay, Amitava [Department of Chemical Engineering, University of Calcutta, Kolkata (India); Das, Sudip Kumar [Department of Chemical Technology, University of Calcutta, Kolkata (India)

    2010-08-15

    Experiments have been carried out to characterize the adsorption of chromium(VI) in the aqueous phase onto dried roots of water hyacinth. Results revealed a very high degree of removal efficiency ({proportional_to}100%). Theoretical analyzes are also made for describing the sorption and diffusion processes. The effective pore diffusivity of chromium(VI) in the water hyacinth roots is determined by a suitable global optimization technique. The depth of penetration, on the other hand, has been estimated for various initial concentrations of chromium(VI). Theoretically predicted concentration profiles are in excellent agreement with the experimental values. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  12. BIOADSORPTION USING COMPOST: AN ALTERNATIVE FOR REMOVAL OF CHROMIUM (VI) FROM AQUEOUS SOLUTIONS

    OpenAIRE

    Claudia Vargas; Pedro F. B. Brandão,; Jesús Ágreda,; Elianna Castillo

    2012-01-01

    The removal of Cr(VI) from aqueous solutions was studied using a compost generated from carnation flowers waste. The highest percentage of removal achieved (ca. 99 %) was obtained at pH 2.0, using a 10 mg L-1 of Cr(VI) solution, a dose of 10 g L-1 of compost, and with an equilibrium time of 3 hours. Under these conditions, the kinetics and adsorption isotherm were examined varying the initial Cr(VI) concentration from 15 to 200 mg L-1. The maximum sorption capacity at equilibrium (Qm), from t...

  13. Reduction of U(VI) by Fe(II) in the presence of hydrous ferric oxide and hematite: effects of solid transformation, surface coverage, and humic acid.

    Science.gov (United States)

    Jang, Je-Hun; Dempsey, Brian A; Burgos, William D

    2008-04-01

    Fe(II) was added to U(VI)-spiked suspensions of hydrous ferric oxide (HFO) or hematite to compare the redox behaviors of uranium in the presence of two different Fe(III) (oxyhydr)oxides. Experiments were conducted with low or high initial sorption density of U(VI) and in the presence or absence of humic acid (HA). About 80% of U(VI) was reduced within 3 days for low sorbed U(VI) conditions, with either hematite or HFO. The {Fe(3+)} in the low U(VI) experiments at 3 days, based on measured Fe(II) and U(VI) and the assumed presence of amorphous UO(2(s)), was consistent with control by HFO for either initial Fe(III) (oxyhydr)oxide. After about 1 day, partial re-oxidation to U(VI) was observed in the low sorbed U(VI) experiments in the absence of HA, without equivalent increase of dissolved U(VI). No reduction of U(VI) was observed in the high sorbed U(VI) experiments; it was hypothesized that the reduction required sorption proximity of U(VI) and Fe(II). Addition of 5mg/L HA slowed the reduction with HFO and had less effect with hematite. Mössbauer spectroscopy (MBS) of (57)Fe(II)-enriched samples identified the formation of goethite, hematite, and non-stoichiometric magnetite from HFO, and the formation of HFO, hydrated hematite, and non-stoichiometric magnetite from hematite.

  14. Sorption isotherm measurements by NMR.

    Science.gov (United States)

    Leisen, Johannes; Beckham, Haskell W; Benham, Michael

    2002-01-01

    An experimental setup is described for the automated recording of sorption isotherms by NMR experiments at precisely defined levels of relative humidity (RH). Implementation is demonstrated for a cotton fabric; Bloch decays. T1 and T2* relaxation times were measured at predefined steps of increasing and decreasing relative humidities (RHs) so that a complete isotherm of NMR properties was obtained. Bloch decays were analyzed by fitting to relaxation functions consisting or a slow- and a fast-relaxing component. The fraction of slow-relaxing component was greater than the fraction of sorbed moisture determined from gravimetric sorption data. The excess slow-relaxing component was attributed to plasticized segments of the formerly rigid cellulose matrix. T1 and T2* sorption isotherms exhibit hysteresis similar to gravimetric sorption isotherms. However, correlating RH to moisture content (MC) reveals that both relaxation constants depend only on MC, and not on the history of moisture exposure.

  15. Biosorbent encapsulation in calcium alginate: Effects of process variables on Cr(VI) removal from solutions.

    Science.gov (United States)

    Šillerová, Hana; Komárek, Michael; Liu, Chang; Poch, Jordi; Villaescusa, Isabel

    2015-09-01

    Selected biosorbents, brewers draff and grape waste, have been encapsulated in calcium alginate beads and used for the removal of Cr(VI) from aqueous solutions. The effects of encapsulation variables, including the type of waste, the percentage of waste in the beads and the curing time of the beads in CaCl2, on the diameters of the beads and Cr(VI) sorption kinetics have been evaluated. In total, 21 different types of beads were produced. The diameters of the beads increased with increasing amounts of encapsulated biomaterial. Beads that contained grape waste were larger than those containing brewers draff. The most efficient beads for Cr(VI) removal were beads that contained 4% (w/w) of grape waste. No significant differences in the kinetics of Cr(VI) sorption were found with respect to the curing time variable in the case of grape waste calcium alginate beads. Statistical analysis confirmed that the type and percentage of waste are the critical parameters influencing the diameters of the beads and Cr(VI) removal. It was proven that the sorption efficiencies of the beads containing draff and grape waste encapsulated under the optimum conditions were much higher than the efficiencies obtained when using both wastes in their native states. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. Studies of anions sorption on natural zeolites.

    Science.gov (United States)

    Barczyk, K; Mozgawa, W; Król, M

    2014-12-10

    This work presents results of FT-IR spectroscopic studies of anions-chromate, phosphate and arsenate - sorbed from aqueous solutions (different concentrations of anions) on zeolites. The sorption has been conducted on natural zeolites from different structural groups, i.e. chabazite, mordenite, ferrierite and clinoptilolite. The Na-forms of sorbents were exchanged with hexadecyltrimethylammonium cations (HDTMA(+)) and organo-zeolites were obtained. External cation exchange capacities (ECEC) of organo-zeolites were measured. Their values are 17mmol/100g for chabazite, 4mmol/100g for mordenite and ferrierite and 10mmol/100g for clinoptilolite. The used initial inputs of HDTMA correspond to 100% and 200% ECEC of the minerals. Organo-modificated sorbents were subsequently used for immobilization of mentioned anions. It was proven that aforementioned anions' sorption causes changes in IR spectra of the HDTMA-zeolites. These alterations are dependent on the kind of anions that were sorbed. In all cases, variations are due to bands corresponding to the characteristic Si-O(Si,Al) vibrations (occurring in alumino- and silicooxygen tetrahedra building spatial framework of zeolites). Alkylammonium surfactant vibrations have also been observed. Systematic changes in the spectra connected with the anion concentration in the initial solution have been revealed. The amounts of sorbed CrO4(2-), AsO4(3-) and PO4(3-) ions were calculated from the difference between their concentrations in solutions before (initial concentration) and after (equilibrium concentration) sorption experiments. Concentrations of anions were determined by spectrophotometric method. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. Biosorption of Cr(VI) and As(V) at high concentrations by organic and inorganic wastes

    Science.gov (United States)

    María Rivas Pérez, Ivana; Paradelo Núñez, Remigio; Nóvoa Muñoz, Juan Carlos; Arias Estévez, Manuel; José Fernández Sanjurjo, María; Álvarez Rodríguez, Esperanza; Núñez Delgado, Avelino

    2016-04-01

    The potential reutilization of several wastes as biosorbents for As(V) and Cr(VI) has been assessed in batch-type experiments. The materials studied were one inorganic: mussel shell, and three organic: pine bark, oak ash and hemp waste. Batch experiments were performed in order to determine the removal capacity of the wastes under conditions of high As(V) and Cr(VI) loads. For this, 3 g of each waste material were added with 30 mL NaNO3 0.01 M dissolutions containing 0, 0.5, 1.5, 3 and 6 mmol As(V) L-1 or Cr(VI) L-1, prepared from analytical grade Na2HAsO4 or K2Cr2O7. The resulting suspensions were shaken for 24 h, centrifuged and filtered. Once each batch experiment corresponding to the sorption trials ended, each individual sample was added with 30 mL of NaNO3 0.01 M to desorb As(V) or Cr(VI), shaken for 24 h, centrifuged and filtered as in the sorption trials. Oak ash showed high sorption (>76%) and low desorption (hemp waste (98%) with very low desorption (hemp waste and mussel shell, that presented very low Cr(VI) sorption (<10%). Sorption data for both elements were better described by the Freundlich than by the Langmuir model. The variable results obtained for the removal of the two anionic contaminants for a given sorbent suggest that different mechanisms govern removal from the solution in each case. In summary, oak ash would be an efficient sorbent material for As(V), but not for Cr(VI), while pine bark would be the best sorbent for Cr(VI) removal.

  18. Vi, de civiliserede

    DEFF Research Database (Denmark)

    Nyemann, Dorthe

    2016-01-01

    Vi har i årtier troet på, at mennesker under de rette omstændigheder kan lykkes med at leve i fred og fordragelighed med hinanden. Skal vi til at erkende, at også vores samfundsstrukturer kun er en tynd fernis ovenpå et utæmmeligt voldspotentiale og egoisme?......Vi har i årtier troet på, at mennesker under de rette omstændigheder kan lykkes med at leve i fred og fordragelighed med hinanden. Skal vi til at erkende, at også vores samfundsstrukturer kun er en tynd fernis ovenpå et utæmmeligt voldspotentiale og egoisme?...

  19. “Stereoscopic” 2D super-microporous phosphazene-based covalent organic framework: Design, synthesis and selective sorption towards uranium at high acidic condition

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Shuang; Zhao, Xiaosheng; Li, Bo; Bai, Chiyao; Li, Yang; Wang, Lei; Wen, Rui; Zhang, Meicheng; Ma, Lijian; Li, Shoujian, E-mail: sjli000616@scu.edu.cn

    2016-08-15

    Highlights: • Phosphorus element was first introduced into covalent organic frameworks (COFs). • Monomer in C{sub 3}-like spatial configuration was first used to construct COF materials. • A new 2D super-microporous phosphazene-based sorbent (MPCOF) was synthesized. • Separation of U (VI) by MPCOF at high acidic media (up to 1M HNO{sub 3}) was achieved. • Selectivity for U (VI) separation from multi-ion solution can reach unreported 92%. - Abstract: So far, only five primary elements (C, H, O, N and B) and two types of spatial configuration (C{sub 2}–C{sub 4}, C{sub 6} and T{sub d}) are reported to build the monomers for synthesis of covalent organic frameworks (COFs), which have partially limited the route selection for accessing COFs with new topological structure and novel properties. Here, we reported the design and synthesis of a new “stereoscopic” 2D super-microporous phosphazene-based covalent organic framework (MPCOF) by using hexachorocyclotriphosphazene (a P-containing monomer in a C{sub 3}-like spatial configuration) and p-phenylenediamine (a linker). The as-synthesized MPCOF shows high crystallinity, relatively high heat and acid stability and distinctive super-microporous structure with narrow pore-size distributions ranging from 1.0–2.1 nm. The results of batch sorption experiments with a multi-ion solution containing 12 co-existing cations show that in the pH range of 1–2.5, MPCOF exhibits excellent separation efficiency for uranium with adsorption capacity more than 71 mg/g and selectivity up to record-breaking 92%, and furthermore, an unreported sorption capacity (>50 mg/g) and selectivity (>60%) were obtained under strong acidic condition (1 M HNO{sub 3}). Studies on sorption mechanism indicate that the uranium separation by MPCOF in acidic solution is realized mainly through both intra-particle diffusion and size-sieving effect.

  20. Zn Isotope Fractionation during Sorption onto Kaolinite.

    Science.gov (United States)

    Guinoiseau, Damien; Gélabert, Alexandre; Moureau, Julien; Louvat, Pascale; Benedetti, Marc F

    2016-02-16

    In this study, we quantify zinc isotope fractionation during its sorption onto kaolinite, by performing experiments under various pH, ionic strength, and total Zn concentrations. A systematic enrichment in heavy Zn isotopes on the surface of kaolinite was measured, with Δ(66)Znadsorbed-solution ranging from 0.11‰ at low pH and low ionic strength to 0.49‰ at high pH and high ionic strength. Both the measured Zn concentration and its isotopic ratio are correctly described using a thermodynamic sorption model that considers two binding sites: external basal surfaces and edge sites. Based on this modeling approach, two distinct Zn isotopic fractionation factors were calculated: Δ(66)Znadsorbed-solution = 0.18 ± 0.06‰ for ion exchange onto basal sites, and Δ(66)Znadsorbed-solution = 0.49 ± 0.06‰ for specific complexation onto edge sites. These two distinct factors indicate that Zn isotope fractionation is dominantly controlled by the chemical composition of the solution (pH, ionic strength).

  1. Sorption study and contribution of ion exchange in the dynamics of {sup 137}Cs n highly weathered soils; Estudo da sorcao e da contribuicao da troca ionica na dinamica do {sup 137}Cs em solos altamente intemperizados

    Energy Technology Data Exchange (ETDEWEB)

    Nascimento Sobrinho, Guilherme Augusto

    2014-08-01

    The present study investigated the sorption kinetics and the reversibility of {sup 137}Cs within highly weathered soils, by means of sorption isotherms and desorption with three concentrations of silver thiourea (AgTU). For this purpose, four soils were selected based on their mineralogy and pedogenetics and sampled from lysimeters placed within the experimental area of the Tropical Radioecology Laboratory of the Institute for Radioprotection and Dosimetry. Three of them were tropical soils, belonging to the Argissolo (ARG), Latossolo vermelho (LV) and Latossolo vermelho amarelo (LVA) classes, and one subtropical, belonging to the Nitossolo (NIT) class. The 'goodness-of-fit' of the constant partition, Langmuir and Freundlich isotherms to the experimental data were assessed by means of a 'traditional' approach, i.e. correlation (R) and determination (R{sup 2}) coefficients, and a 'theoretic-informative' one, based upon the Corrected Akaike Information Criteria (AICc). In this work became clear that even presenting high affinity for the soil surface, once the sorption equilibrium was reached within 24 h (66 to 97% of sorbed {sup 137}Cs), quite a lot of this radionuclide remains easily mobile (40 to 73% of desorbed {sup 137}Cs), by means of a single extraction with AgTU 0,05 mol.L-1, and that such reversibility relates in an inverse manner to the sorption capacity of the studied soils for {sup 137}Cs. This work pointed also that the constant partition model, mostly known as Kdi, does not fit at all for the sorption data gathered for four highly weathered soils from four mineralogical groups, and for a very dilute solution of {sup 137}Cs. The mathematical model that most adequately described the sorption data for the four studied soils was the Langmuir equation (R{sup 2} > 0,95). The multi model analysis was not able to support generalizations for the four soils. The three models considered in this study provided good predictions of the

  2. Selective removal of chromium (VI) from sulphates and other metal ...

    African Journals Online (AJOL)

    Leaching of the chromate template from the polymer particles was achieved with successive stirring of the ion-imprinted polymer (IIP) particles in 4 M HNO3 solutions to obtain leached materials, which were then used for selective rebinding of Cr (VI) ions from aqueous solutions. Similarly, the non-imprinted polymer/control ...

  3. Sorption of sodium hydroxide by type I collagen and bovine corneas.

    Science.gov (United States)

    Whikehart, D R; Edwards, W C; Pfister, R R

    1991-01-01

    There are no quantitative studies on the uptake of alkali into corneal tissues. To study this phenomenon, both type I collagen and bovine corneas were incubated in sodium hydroxide (NaOH) under varying conditions for periods up to 27.5 h. The sorption (absorption or adsorption) of the alkali to protein and tissue was measured as the quantity of NaOH no longer available for titration to neutrality with hydrochloric acid. Sorption was found to be dependent on the concentration of NaOH (0.01-1 N) but independent of the incubation temperature (4-35 degrees C). In whole cornea, sorption of 1 N NaOH began immediately and increased with time up to 6 h. After 6 h, sorption decreased, together with the observed degradation and solubilization of the tissue. Stripping of the corneal endothelium alone or of the endothelium and epithelium increased sorption in a similar manner when compared to whole corneas for periods up to 4 h. These observations are compatible with ionic and nonionic bonding of hydroxide ions to collagen (including that of the cornea) and the subsequent release of hydroxide ions during hydrolysis of the protein itself. Indirect evidence also suggests the inclusion of quantities of unbound hydroxide ions in hydrated gels of glycosaminoglycans. It is proposed that in a chemical burn of the cornea, alkali is both stored in the tissue (by sorption) and reacted with it (by hydrolysis), without any net consumption of alkali taking place.

  4. Interaction of aerobic soil bacteria with plutonium(VI)

    Energy Technology Data Exchange (ETDEWEB)

    Panak, P.J. [Lawrence Berkeley National Lab., Berkeley, CA (United States). Chemical Sciences Div.; Nitsche, H. [Lawrence Berkeley National Lab., Berkeley, CA (United States). Chemical Sciences Div.; California Univ., Berkeley, CA (United States). Dept. of Chemistry

    2001-07-01

    We studied the interaction of Pu(VI) with Pseudomonas stutzeri ATCC 17588 and Bacillus sphaericus ATCC 14577, representatives of the main aerobic groups of soil bacteria present in the upper soil layers. The biosorption studies have shown that these soil bacteria accumulate high amounts of Pu(VI). The relative sorption efficiency toward Pu(VI) related to the amount of biomass used decreased with increasing biomass concentration due to increased agglomeration of the bacteria resulting in a decrease of the number of available complexing groups. Spores of Bacillus sphaericus showed a higher biosorption than the vegetative cells at low biomass concentration which decreased significantly with increasing biomass concentration. At higher biomass concentrations (> 0.7 g/L), the vegetative cells of both strains and the spores of B. sphaericus showed comparable sorption efficiencies. Investigations on the pH dependency of the biosorption and extraction studies with 0.01 M EDTA solution have shown that the biosorption of plutonium is a reversible process and the plutonium is bound by surface complexation. Optical absorption spectroscopy showed that one third of the initially present Pu(VI) was reduced to Pu(V) after 24 hours. Kinetic studies and solvent extraction to separate different oxidation states of Pu after contact with the biomass provided further information on the yield and the kinetics of the bacteria-mediated reduction. Long-term studies showed that also 16% of Pu(IV) was formed after one month. The slow kinetics of this process indicate that under our experimental conditions the Pu(IV) was not a produced by microbial reduction but seemed to be rather the result of the disproportionation of the formed Pu(V) or autoreduction of Pu(VI). (orig.)

  5. Biosorption of uranium (VI) by immobilized Aspergillus fumigatus beads

    Energy Technology Data Exchange (ETDEWEB)

    Wang Jingsong, E-mail: xhwjs@163.co [School of Urban Construction, University of South China, 28 West Changsheng Road, Hengyang, Hunan 421001 (China) and Hunan Key Laboratory of Pollution Control and Resource Reuse, University of South China, Henyang, Hunan 421001 (China); Hu Xinjiang [School of Urban Construction, University of South China, 28 West Changsheng Road, Hengyang, Hunan 421001 (China); College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Liu Yunguo [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Xie Shuibo [School of Urban Construction, University of South China, 28 West Changsheng Road, Hengyang, Hunan 421001 (China); Hunan Key Laboratory of Pollution Control and Resource Reuse, University of South China, Henyang, Hunan 421001 (China); Bao Zhenglei [School of Urban Construction, University of South China, 28 West Changsheng Road, Hengyang, Hunan 421001 (China)

    2010-06-15

    Biosorption of uranium (VI) ions by immobilized Aspergillus fumigatus beads was investigated in a batch system. The influences of solution pH, biosorbent dose, U (VI) concentration, and contact time on U (VI) biosorption were studied. The results indicated that the adsorption capacity was strongly affected by the solution pH, the biosorbent dose and initial U (VI) concentration. Optimum biosorption was observed at pH 5.0, biosrobent dose (w/v) 2.5%, initial U (VI) concentration 60 mg L{sup -1}. Biosorption equilibrium was established in 120 min. The adsorption process conformed to the Freunlich and Temkin isothermal adsorption models. The dynamic adsorption model conformed to pseudo-second order model.

  6. Competitive sorption of heavy metal by soils. Isotherms and fractional factorial experiments.

    Science.gov (United States)

    Echeverría, J C; Morera, M T; Mazkiarán, C; Garrido, J J

    1998-01-01

    Competing ions strongly affect heavy metal sorption onto the solid surfaces of soil. This study evaluated competitive sorption of Cd, Cu, Ni, Pb and Zn on three soils: Calcixerollic Xerochrept, Paralithic Xerorthent and Lithic Haplumbrept. Monometal and competitive sorption isotherms were obtained at 25 degrees C. The individual effect of ions on retention of the others was ascertained by a fractional factorial analysis design. Most of the sorption isotherms belonged to type L subtype 2 in the classification of Giles. In competitive sorption the initial linear part was shorter and the knee sharper when compared with monometal sorption isotherms. Parameters related to sorptive capacity, such as Point B, Langmuir monolayer and Freundlich distribution coefficient, were higher in monometal than in competitive sorption, and in basic soils than in acidic soil. Calcium desorbed at different points of the sorption isotherms indicated that cationic exchange with Ca was the main retention mechanism in calcareous soils. For Pb, the ratio Ca desorbed/Pb sorbed was close to one; for Cu, Ni and Zn the ratio ranged from 1.20 to 1.37, probably due to partial dissolution of calcium carbonates by hydrolytic processes during retention. On the other hand, Cd had a ratio around 0.6 reflecting another additional retention mechanism, probably surface complexation. Fractional factorial design confirmed that the presence of the cations investigated reduced the amount of the five metals retained, but the presence of Cu and Pb in the system depressed Ni, Cd and Zn sorption more than the inverse. Cation mobility was enhanced when equilibrium concentration increased and the effect was higher in Ca-saturated soils.

  7. Sorption isotherms, GAB parameters and isosteric heat of sorption

    NARCIS (Netherlands)

    Quirijns, E.J.; Boxtel, van A.J.B.; Loon, van W.K.P.; Straten, van G.

    2005-01-01

    The diffusion-sorption drying model has been developed as a physics-based way to model the decreasing drying rate at low moisture contents. This new model is founded on the existence of different classes of water: free and bound water. The transition between these classes and the corresponding

  8. Polymer based nanocomposites for the removal of Cr(VI) from water

    CSIR Research Space (South Africa)

    Setshedi, K

    2012-10-10

    Full Text Available .3 pH 2 pH 6 % R em ov al pH Feasibility test for Cr(VI) contaminated ground water and the effect of competing ions 100 ppm Cr(VI) sol. Nanocomposite + Cr(VI) sol 0 ppm Cr(VI) sol. 0 20 40 60 80 100 Q e( m g/ g) Cr 6+ Cr 6... nanocomposites for the removal of Cr(VI) from water Emerging Researcher Symposium Katlego Setshedi 10 October 2012 Outline ? CSIR 2012 Slide 2 ? Background ? Problem statement ? Health impacts ? Remedies ? Objectives ? Experimental procedure...

  9. Competitive and Noncompetitive Batch Sorption Studies of Aqueous Cd(II) and Pb(II) Uptake onto Coffea canephora Husks, Cyperus papyrus Stems, and Musa spp. Peels

    OpenAIRE

    Bakyayita, G. K.; Norrström, A. C.; Kulabako, R. N.

    2015-01-01

    Coffea canephora, Cyperus papyrus, and Musa spp. were studied for competitive and noncompetitive removal of aqueous Cd2+ and Pb2+. The optimal conditions were pH 4.5 and agitation time 3.0 hours. Biomass constituent ions showed no interference effects whereas cation exchange capacity values corresponded to the sorption efficiencies. XRD spectroscopy revealed surface oxygen and nitrogen groups that provide binding sites for metal ions. The maximum sorption efficiency ranges for metal ions in n...

  10. Sorption media for stormwater treatment

    DEFF Research Database (Denmark)

    Wium-Andersen, Tove; Nielsen, Asbjørn Haaning; Hvitved-Jacobsen, Thorkild

    2012-01-01

    Five sorption materials were studied with focus on polishing pretreated stormwater: crushed limestone, shell-sand, zeolite and two granulates of olivine. These materials are commercially available at comparatively low cost and have been subjected to a minimum of modification from their natural st...... be designed for long life expectancy at comparatively low cost by applying the materials tested....

  11. Moisture Sorption in Porous Materials

    DEFF Research Database (Denmark)

    Nielsen, Lauge Fuglsang

    2007-01-01

    Abstract: Information on pore geometry is very important in any study of the mechanical and physical behavior of porous materials. Unfortunately pores are not very accessible for direct measurements. Indirect methods have to be used which involve impregnation (sorption) experiments from which...... in the subject considered this software is available on request to the author. Keywords: Porous materials, moisture, adsorption, desorption, BET-parameters....

  12. Sorption properties of modified zeolit

    Directory of Open Access Journals (Sweden)

    Beikut Balgysheva

    2011-12-01

    Full Text Available The modification of zeolites in the presence of sodium phosphate hydrogen in a mechanical chemical activation (type of mill is “NATO” №2607 was carried out. High degree of sorption of k =87.5% at a ratio of zeolite : Mn2+ = 1 : 150 and duration 60 min, СMn2+ -1000 mkg/L was determined.

  13. Interaction of monosaccharides and related compounds with oxocations of Mo(VI), W(VI) and U(VI) studied by NMR spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Geraldes, C.F.G.C.; Castro, M.M.C.A.; Saraiva, M.E.; Aureliano, M.; Dias, B.A.

    1988-05-01

    Proton, /sup 13/C and /sup 31/P nuclear magnetic resonance spectroscopy has been used to study the complexation of Mo(VI), W(VI) and U(VI) oxocations with various aldoses, cyclic polyols and ribose-5-phosphate in aqueous solution. The aldoses D-mannose, D-lyxose and D-ribose form tridentate complexes with Mo(VI) and W(VI) at pH similarly ordered 5, via the 1,2,3-hydroxyl groups, which are cis to each other in these sugars. Other aldoses, like D-arabinose, D-glucose, D-xylose and D-galactose form weaker bidentate complexes with those ions because they can only use the 1 and 3-cis hydroxyl groups in metal binding. These bidentate interactions also take place in the binding of U(VI) to D-mannose and D-ribose, at pH similarly ordered 10. However, sugars having 1,3,5-hydroxyl groups in the cis position do not form stable chelates with these oxocations, possibly due to steric crowding. In the case of ribose-5-phosphate, the phosphate group is the exclusive binding site for the three oxocations, except for U(VI) at very basic pH (pH > 10), where the hydroxyl groups also interact with UO/sub 2//sup 2 +/.

  14. and dioxouranium(vi)

    African Journals Online (AJOL)

    a

    Thorium(IV) and uranium(VI) with atomic radii of 1.65 and .... to ν(NH) vibrations. Practically no effect on these frequencies after complexation precludes the possibility of metal-coordination at this group. The absorptions at 1600 ... observation suggests involvement of unsaturated nitrogen atoms of the two azomethine groups.

  15. The role of sediment properties and solution pH in the adsorption of uranium(VI) to freshwater sediments.

    Science.gov (United States)

    Crawford, Sarah E; Lofts, Stephen; Liber, Karsten

    2017-01-01

    Uranium (U) can enter aquatic environments from natural and anthropogenic processes, accumulating in sediments to concentrations that could, if bioavailable, adversely affect benthic organisms. To better predict the sorption and mobility of U in aquatic ecosystems, we investigated the sediment-solution partition coefficients (Kd) of U for nine uncontaminated freshwater sediments with a wide range of physicochemical characteristics over an environmentally relevant pH range. Test solutions were reconstituted to mimic water quality conditions and U(VI) concentrations (0.023-2.3 mg U/L) found downstream of Canadian U mines. Adsorption of U(VI) to each sediment was greatest at pH 6 and 7, and significantly reduced at pH 8. There were significant differences in pH-dependent sorption among sediments with different physicochemical properties, with sorption increasing up until thresholds of 12% total organic carbon, 37% fine fraction (≤50 μm), and 29 g/kg of iron content. The Kd values for U(VI) were predicted using the Windermere Humic Aqueous Model (WHAM) using total U(VI) concentrations, and water and sediment physicochemical parameters. Predicted Kd-U values were generally within a factor of three of the observed values. These results improve the understanding and assessment of U sorption to field sediment, and quantify the relationship with sediment properties that may influence the bioavailability and ecological risk of U-contaminated sediments. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Flow injection on-line preconcentration of low levels of Cr(VI) with detection by ETAAS

    DEFF Research Database (Denmark)

    Som-aum, Waraporn; Liawruangrath, Saisunee; Hansen, Elo Harald

    2002-01-01

    A flow injection (FI) on-line sorption preconcentration procedure utilizing a packed column reactor and combined with electrothermal atomic absorption spectrometry (ETAAS) is proposed for the determination of low levels of Cr(VI) in water samples. Polytetrafluoroethylene (PTFE) beads packed...

  17. Equilibrium, kinetic and thermodynamic studies for sorption of Ni (II from aqueous solution using formaldehyde treated waste tea leaves

    Directory of Open Access Journals (Sweden)

    Jasmin Shah

    2015-05-01

    Full Text Available The sorption characteristic of Ni (II from aqueous solution using formaldehyde treated waste tea leaves as a low cost sorbent has been studied. The effect of pH, contact time, sorbent dose, initial metal ion concentration and temperature were investigated in batch experiments. The equilibrium data were fitted into four most common isotherm models; Freundlich, Langmuir, Tempkin and Dubinin–Radushkevich (D–R. The Langmuir model described the sorption isotherm best with maximum monolayer sorption capacity of 120.50 mg g−1. Four kinetic models, pseudo-first-order, pseudo-second-order, intraparticle diffusion and Elovich were employed to explain the sorption mechanism. The kinetics of sorption data showed that the pseudo-second-order model is the best with correlation coefficient of 0.9946. The spontaneous and exothermic nature of the sorption process was revealed from thermodynamic investigations. The effect of some common alkali and alkaline earth metal ions were also studied which showed that the presence of these ions have no effect on the sorption of Ni (II. The results showed that waste tea leaves have the potential to be used as a low cost sorbent for the removal of Ni (II from aqueous solutions.

  18. short communication binding of nickel and zinc ions with activated ...

    African Journals Online (AJOL)

    a

    ABSTRACT. Activated carbon was prepared from sugar cane fibre by carbonizing at 500 oC for 30 minutes. ... Equilibrium sorption of nickel and zinc ions by the activated carbon was studied using a range of metal ion .... which means that limited sorption cycles will be required in the treatment of waste water containing the ...

  19. Pervaporation with ion exchange membranes

    Energy Technology Data Exchange (ETDEWEB)

    Boeddeker, K.W.; Wenzlaff, A.

    1986-01-01

    Sorption and pervaporation of aqueous-organic solvent systems (water-ethanol; water-carboxylic acids) with commercial ion exchange membranes are compared to obtain information on polymersolvent interaction vs. coupling. Close agreement between sorption selectivity and pervaporation selectivity indicates coupling. If pervaporation is less selective than sorption, polymer-solvent interaction overtakes coupling, the limit of de-coupling being phase separation within the sorbate as signaled by a sudden increase in permeability of the lesser interacting component. As long as sorption and pervaporation operate in parallel, favoring enrichment of the same component, coupling enhances the separation effect. If pervaporation counteracts sorption, coupling is detrimental to the separation effect. Potential applications include the dehydration of pre-concentrated water-ethanol using anion exchange membranes, and the enrichment of acetic acid from dilute aqueous solution by pervaporative removal of water through cation exchange membranes.

  20. Interaction of aerobic soil bacteria with plutonium(VI)

    Energy Technology Data Exchange (ETDEWEB)

    Panak, Petra J.; Nitsche, Heino

    2000-08-22

    We studied the interaction of Pu(VI) with Pseudomonas stutzeri ATCC 17588 and Bacillus sphaericus ATCC 14577, representatives of the main aerobic groups of soil bacteria present in the upper soil layers. The accumulation studies have shown that these soil bacteria accumulate high amounts of Pu(VI). The sorption efficiency toward Pu(VI) decreased with increasing biomass concentration due to increased agglomeration of the bacteria resulting in a decreased total surface area and number of available complexing groups. Spores of Bacillus sphaericus showed a higher biosorption than the vegetative cells at low biomass concentration which decreased significantly with increasing biomass concentration. At higher biomass concentrations (> 0.7 g/L), the vegetative cells of both strains and the spores of B. sphaericus showed comparable sorption efficiencies. Investigations on the pH dependency of the biosorption and extraction studies with 0.01 M EDTA solution have shown that the biosorption of plutonium is a reversible process and the plutonium is bound by surface complexation. Optical absorption spectroscopy showed that one third of the initially present Pu(VI) was reduced to Pu(V) after 24 hours. Kinetic studies and solvent extraction to separate different oxidation states of Pu after contact with the biomass provided further information on the yield and the kinetics of the bacteria-mediated reduction. Long-term studies showed that also 16% of Pu(IV) was formed after one month. The comparison of the amount of Pu(IV) formed during that time period with literature data of the Pu(V) disproportionation, indicated that the Pu(IV) seemed to be rather the result of the disproportionation of the formed Pu(V) than of a further microbial reduction.

  1. II-VI semiconductor compounds

    CERN Document Server

    1993-01-01

    For condensed matter physicists and electronic engineers, this volume deals with aspects of II-VI semiconductor compounds. Areas covered include devices and applications of II-VI compounds; Co-based II-IV semi-magnetic semiconductors; and electronic structure of strained II-VI superlattices.

  2. Investigating the gas sorption mechanism in an rht -metal-organic framework through computational studies

    KAUST Repository

    Pham, Tony T.

    2014-01-09

    Grand canonical Monte Carlo (GCMC) simulations were performed to investigate CO2 and H2 sorption in an rht-metal-organic framework (MOF) that was synthesized with a ligand having a nitrogen-rich trigonal core through trisubstituted triazine groups and amine functional groups. This MOF was synthesized by two different groups, each reporting their own distinct gas sorption measurements and crystal structure. Electronic structure calculations demonstrated that the small differences in the atomic positions between each group\\'s crystal structure resulted in different electrostatic parameters about the Cu2+ ions for the respective unit cells. Simulations of CO2 sorption were performed with and without many-body polarization effects and using our recently developed CO2 potentials, in addition to a well-known bulk CO2 model, in both crystallographic unit cells. Simulated CO2 sorption isotherms and calculated isosteric heats of adsorption, Qst, values were in excellent agreement with the results reported previously by Eddaoudi et al. for both structures using the polarizable CO2 potential. For both crystal structures, the initial site for CO2 sorption were the Cu 2+ ions that had the higher positive charge in the unit cell, although the identity of this electropositive Cu2+ ion was different in each case. Simulations of H2 sorption were performed with three different hydrogen potentials of increasing anisotropy in both crystal structures and the results, especially with the highest fidelity model, agreed well with Eddaoudi et al.\\'s experimental data. The preferred site of H 2 sorption at low loading was between two Cu2+ ions of neighboring paddlewheels. The calculation of the normalized hydrogen dipole distribution for the polarizable model in both crystal structures aided in the identification of four distinct sorption sites in the MOF, which is consistent to what was observed in the experimental inelastic neutron scattering (INS) spectra. Lastly, while the

  3. Competitive and Noncompetitive Batch Sorption Studies of Aqueous Cd(II and Pb(II Uptake onto Coffea canephora Husks, Cyperus papyrus Stems, and Musa spp. Peels

    Directory of Open Access Journals (Sweden)

    G. K. Bakyayita

    2015-01-01

    Full Text Available Coffea canephora, Cyperus papyrus, and Musa spp. were studied for competitive and noncompetitive removal of aqueous Cd2+ and Pb2+. The optimal conditions were pH 4.5 and agitation time 3.0 hours. Biomass constituent ions showed no interference effects whereas cation exchange capacity values corresponded to the sorption efficiencies. XRD spectroscopy revealed surface oxygen and nitrogen groups that provide binding sites for metal ions. The maximum sorption efficiency ranges for metal ions in noncompetitive media were 95.2–98.7% for C. canephora, 42.0–91.3% for C. papyrus, and 79.9–92.2% for Musa spp. and in competitive sorption 90.8–98.0% for C. canephora, 19.5–90.4% for C. papyrus, and 56.4–89.3% for Musa spp. The Pb2+ ions uptake was superior to that of Cd2+ ions in competitive and noncompetitive media. In competitive sorption synergistic effects were higher for Cd2+ than Pb2+ ions. The pseudo-second-order kinetic model fitted experimental data with 0.917≤R2≥1.000 for Pb2+ ions and 0.711≤R2≥0.999 for Cd2+ ions. The Langmuir model fitted noncompetitive sorption data with 0.769≤R2≥0.999; moreover the Freundlich model fitted competitive sorption data with 0.867≤R2≥0.989. Noncompetitive sorption was monolayer chemisorption whereas competitive sorption exhibited heterogeneous sorption mechanisms.

  4. Sorption Kinetics Of Selected Heavy Metals Adsorption To Natural And Fe(III) Modified Zeolite Tuff Containing Clinoptilolite Mineral

    Science.gov (United States)

    Sirotiak, Maroš; Lipovský, Marek; Bartošová, Alica

    2015-06-01

    In the research described in this paper, studied was sorption capacity of natural and ferric modification of zeolite tuff containing mineral clinoptilolite from the Nižný Hrabovec deposit to remove potentially toxic metals (ionic forms of chromium, nickel, copper and aluminium) from their water solutions. We reported that the Fe (III) zeolite has an enhanced ability to sorption of Cu (II), and a slight improvement occurs in the case of Cr (VI) and Ni (II). On the other hand, the deterioration was observed in the case of Al (III) adsorption.

  5. A sorption model for alkalis in cement-based materials - Correlations with solubility and electrokinetic properties

    Science.gov (United States)

    Henocq, Pierre

    2017-06-01

    In cement-based materials, radionuclide uptake is mainly controlled by calcium silicate hydrates (C-S-H). This work presents an approach for defining a unique set of parameters of a surface complexation model describing the sorption behavior of alkali ions on the C-S-H surface. Alkali sorption processes are modeled using the CD-MUSIC function integrated in the Phreeqc V.3.0.6 geochemical code. Parameterization of the model was performed based on (1) retention, (2) zeta potential, and (3) solubility experimental data from the literature. This paper shows an application of this model to sodium ions. It was shown that retention, i.e. surface interactions, and solubility are closely related, and a consistent sorption model for radionuclides in cement-based materials requires a coupled surface interaction/chemical equilibrium model. In case of C-S-H with low calcium-to-silicon ratios, sorption of sodium ions on the C-S-H surface strongly influences the chemical equilibrium of the C-S-H + NaCl system by significantly increasing the aqueous calcium concentration. The close relationship between sorption and chemical equilibrium was successfully illustrated by modeling the effect of the solid-to-liquid ratio on the calcium content in solution in the case of C-S-H + NaCl systems.

  6. Sorption Characteristics of Organic Powder Sorption Material in Fluidized Bed with a Cooling Pipe

    Science.gov (United States)

    Horibe, Akihiko; Husain, Syahrul; Inaba, Hideo; Haruki, Naoto

    The dynamic sorption characteristics of organic sorbent materials have been studied by using fluidized bed with a cooling pipe. The organic powder type sorbent made from a bridged complex of sodium polyacrylate which is one of the sorption polymers is adopted in this study. Sorption rate of water vapor and the variation of temperature in the sorbent bed with time were measured under various conditions. As a result, sorption ratio increases and the completion time for the sorption process decreases by using a cooling pipe. Furthermore, the non-dimensional correlation equations were obtained for water vapor mass transfer under sorption process in terms of relevant non-dimensional parameters.

  7. Sorption of perfluoroalkyl substances in sewage sludge.

    Science.gov (United States)

    Milinovic, Jelena; Lacorte, Silvia; Rigol, Anna; Vidal, Miquel

    2016-05-01

    The sorption behaviour of three perfluoroalkyl substances (PFASs) (perfluorooctanesulfonic acid (PFOS), perfluorooctanoic acid (PFOA) and perfluorobutanesulfonic acid (PFBS)) was studied in sewage sludge samples. Sorption isotherms were obtained by varying initial concentrations of PFOS, PFOA and PFBS. The maximum values of the sorption solid-liquid distribution coefficients (Kd,max) varied by almost two orders of magnitude among the target PFASs: 140-281 mL g(-1) for PFOS, 30-54 mL g(-1) for PFOA and 9-18 mL g(-1) for PFBS. Freundlich and linear fittings were appropriate for describing the sorption behaviour of PFASs in the sludge samples, and the derived KF and Kd,linear parameters correlated well. The hydrophobicity of the PFASs was the key parameter that influenced their sorption in sewage sludge. Sorption parameters and log(KOW) were correlated, and for PFOS (the most hydrophobic compound), pH and Ca + Mg status of the sludge controlled the variation in the sorption parameter values. Sorption reversibility was also tested from desorption isotherms, which were also linear. Desorption parameters were systematically higher than the corresponding sorption parameters (up to sixfold higher), thus indicating a significant degree of irreversible sorption, which decreased in the sequence PFOS > PFOA > PFBS.

  8. VI Nukitsa konkurss

    Index Scriptorium Estoniae

    2002-01-01

    VI Nukitsa konkursi auhinnad: Kirjanikud: I - Henno Käo ("Kusagil mujal"); II - Aidi Vallik ("Kuidas elad, Ann?"); III - Artur Jurin ("Piletijaht: uued segadused Kilulibeda teel"). Kunstnikud: I - Karel Korp (Leelo Tungla ja Karel Korbi "Tema amet"); II - Edgar Valter ("Kuidas õppida vaatama?"); III - Artur Jurin - ("Piletijaht: uued segadused Kilulibeda teel"). Täiskasvanute küsitluse võitis nii teksti kui piltidega Ene-Maris Tali ja Tarmo Tali "Tähtraamat. Aastaring Maarjamaal"

  9. Formation of a ternary neptunyl(V) biscarbonato inner-sphere sorption complex inhibits calcite growth rate.

    Science.gov (United States)

    Heberling, Frank; Scheinost, Andreas C; Bosbach, Dirk

    2011-06-01

    Neptunyl, Np(V)O(2)(+), along with the other actinyl ions U(VI)O(2)(2+) and Pu(V,VI)O(2)((+,2+)), is considered to be highly mobile in the geosphere, while interaction with mineral surfaces (inner- or outer-sphere adsorption, ion-exchange, and coprecipitation/structural incorporation) may retard its migration. Detailed information about the exact interaction mechanisms including the structure and stoichiometry of the adsorption complexes is crucial to predict the retention behavior in diverse geochemical environments. Here, we investigated the structure of the neptunyl adsorption complex at the calcite-water interface at pH 8.3 in equilibrium with air by means of low-temperature (15K) EXAFS spectroscopy at the Np-L(III) edge. The coordination environment of neptunyl consists of two axial oxygen atoms at 1.87(±0.01)Å, and an equatorial oxygen shell of six atoms at 2.51(±0.01)Å. Two oxygen backscatterers at 3.50(±0.04)Å along with calcium backscatterers at 3.95(±0.03)Å suggest that neptunyl is linked to the calcite surface through two monodentate bonds towards carbonate groups of the calcite surface. Two additional carbon backscatterers at 2.94(±0.02)Å are attributed to two carbonate ions in bidentate coordination. This structural environment is conclusively interpreted as a ternary surface complex, where a neptunyl biscarbonato complex sorbs through two monodentate carbonate bonds to steps at the calcite (104) face, while the two bidentately coordinated carbonate groups point away from the surface. This structural information is further supported by Mixed Flow Reactor (MFR) experiments. They show a significant decrease of the calcite growth rate in the presence of neptunyl(V), in line with blockage of the most active crystal growth sites, step and kink sites, by adsorption of neptunyl. Formation of this sorption complex constitutes an important retention mechanism for neptunyl in calcite-rich environments. Copyright © 2011 Elsevier B.V. All rights

  10. Investigations on uranium sorption on bentonite and montmorillonite, respectively, and uranium in environmental samples; Untersuchungen zur Uransorption an Bentonit bzw. Montmorillonit sowie von Uran in Umweltproben

    Energy Technology Data Exchange (ETDEWEB)

    Azeroual, Mohamed

    2010-09-22

    The geotechnical barrier is an important component of a geological repository and consists of compacted bentonite surrounding radioactive waste containers. Its most important functions are, to retard the radionuclide migration into the biosphere and to prevent groundwater contact with containers. lt is therefore of central importance to investigate the bentonite material on its capacity to sorb radionuclides under near-natural chemical and physical conditions. The purpose of this work was to study the adsorption of uranium(VI) on bentonit and on montmorillonite-standards at high uranium concentrations. Thereby, a special account was given to the calcium-uranyl-carbonate complexation, which leads to the formation of very stable and mobile uncharged Ca{sub 2}UO{sub 2}(CO{sub 3}){sub 3} complex. Results of batch experiments showed that the dicalcium-uranyl-tricarbonate complexation lowers the uranium(VI) sorption on natural clay (bentonite) by a factor of up to 3. After 21 days of contact time, about 40 % and 20 % of the initial uranium(VI)concentration were sorbed on Na-bentonite and ea-bentonite, respectively, from a solution with Ca{sub 2}UO{sub 2}(CO{sub 3}){sub 3} dominating the uranium(VI) speciation. On the contrary, about 55 % of the initial uranium(VI)-concentration were sorbed on thes clays from the solution, in which (UO{sub 2}){sub 2}CO{sub 3}(OH){sub 3}{sup -} complex dominated the uranium(VI) speciation. Thus uranium(VI) sorption is more strongly influenced by the solution composition than by bentonite type. Na-bentonite should be used instead of ea-bentonite as a geotechnical barrier, since calcium-uranyl-carbonate complexation may be a realistic scenario. Further SEM-EDX and HREM-EDX studies showed that uranium(VI) sorption occurred predominantly on montmorillonite, which is the main component of bentonite. Uranium(VI) sorption on bentonite's accessory Minerals (pyrite, calcite, mica, and feldspar) was not observed. Investigation of uranium(VI

  11. Contribution to the study of sorption mechanisms at solid-liquid interfaces: application to the cases of apatites and oxy-hydroxides; Contribution a l'etude des mecanismes de sorption aux interfaces solide-liquide: application aux cas des apatites et des oxy-hydroxydes

    Energy Technology Data Exchange (ETDEWEB)

    Duc, M

    2002-11-15

    Sorption-desorption phenomena play an important role in the transport of toxic and radioactive elements in surface and underground water in contact with solid matter. Selenium, which is one of the long-lived radionuclides present in radioactive waste, is characterized by several oxidation states and by anionic species in aqueous solutions. In order to predict its transport, we need a good knowledge of its sorption processes. We have studied the sorption of Se(IV) and Se(VI) on two types of solids present in natural media or which have been proposed as additives to active barriers: hydroxy-apatites, fluoro-apatite and iron oxi-hydroxides (goethite and hematite). Sorption mechanisms have been studied through an approach including several different and complementary methods: titrimetry, zeta-metry, scanning and transmission electron microscopy, infrared spectroscopy, X-ray diffraction, X-ray photo electron spectroscopy, etc... Results showed that Se(VI) is much less sorbed than Se(VI) on both types of solids. For Se(IV) the sorption mechanisms are different for iron oxides and apatites. On oxides, sorption increases when pH decreases. It can be interpreted by a surface complexation model, essentially through an inner sphere complex (monodentate or bidentate). Modelling of Se sorption curves was performed after the determination of acido-basic properties of oxides. However, the determination of the intrinsic properties of oxides is disturbed by several parameters identified as impurities, evolution of the solid in solution, kinetic and solubility of the solid. For apatites, selenium sorption proceeds by exchange with superficial groups, with a maximum of fixation at approximately pH 8. Thanks to XPS measurements and the elaboration of a mathematical model, we could determine the depth of penetration of both selenium and cadmium on apatites. (author)

  12. Mechanisms of cesium sorption onto magnetite

    Energy Technology Data Exchange (ETDEWEB)

    Granizo, N.; Missana, T. [CIEMAT, Dept. de Medioambiente, Madrid (Spain)

    2006-07-01

    One of the current options for the final disposal of high level radioactive wastes is the deep geological repository (DGR). The metal canisters represent the first physical barrier to radionuclide migration towards the geosphere and their corrosion products may play a significant role in sequestering radionuclides by sorption and/or (co)precipitation phenomena. In this work, the sorption of {sup 137}Cs on pure nanocrystalline magnetite has been experimentally studied in a wide range of pH, ionic strength, and radionuclide and sorbent concentration. The magnetite was synthesized in laboratory under controlled conditions and its main physico-chemical properties as microstructure, surface area and surface charge were analysed previous to sorption experiments. Sorption was negligible up to pH 8.5 and maximum sorption values were reached around pH 12. A significant increase in Cs sorption was observed when decreasing the ionic strength. Linear sorption isotherms were observed within the range of Cs concentration used (up to 10{sup -6} M). As expected, Cs showed very small sorption onto the oxide, but the whole experimental results could be satisfactorily fit with a simple model. In addition, the model developed in the oxide-electrolyte system was able to reproduce fairly well the sorption of Cs onto magnetite in two more complex waters (synthetic bentonite and cement porewaters). All the possible effects on sorption that could increase the uncertainties on the (small) sorption values were analysed in depth. In addition, the possible influence of mineral trace impurities on the sorption (for example silicates from experimental vessels), already discussed in the literature, was avoided. (orig.)

  13. (VI) from water by micro-alloyed aluminium composite (MAlC)

    African Journals Online (AJOL)

    driniev

    2004-07-03

    Jul 3, 2004 ... Abstract. This paper deals with Cr(VI) ion removal from water, by micro-alloyed aluminium composite (MAlC), under flow conditions. In a water ... Cr(VI) were below the maximal allowed concentrations for drinking water, in all model solutions. ... mucous membrane irritant and some of these hexavalent com-.

  14. Effect of different solutes, natural organic matter, and particulate Fe(III) on ferrate(VI) decomposition in aqueous solutions.

    Science.gov (United States)

    Jiang, Yanjun; Goodwill, Joseph E; Tobiason, John E; Reckhow, David A

    2015-03-03

    This study investigated the impacts of buffer ions, natural organic matter (NOM), and particulate Fe(III) on ferrate(VI) decomposition and characterized Fe(VI) decomposition kinetics and exposure in various waters. Homogeneous and heterogeneous Fe(VI) decomposition can be described as a second- and first-order reaction with respect to Fe(VI), respectively. Fe(VI) decay was catalyzed by Fe(VI) decomposition products. Solutes capable of forming complexes with iron hydroxides retarded Fe(VI) decay. Fractionation of the resulting solutions from Fe(VI) self-decay and ferric chloride addition in borate- and phosphate-buffered waters showed that phosphate could sequester Fe(III). The nature of the iron precipitate from Fe(VI) decomposition was different from that of freshly precipitated ferric hydroxide from ferric chloride solutions. The stabilizing effects of different solutes on Fe(VI) are in the following order: phosphate > bicarbonate > borate. The constituents of colored and alkaline waters (NOM and bicarbonate) inhibited the catalytic effects of Fe(VI) decomposition products and stabilized Fe(VI) in natural waters. Because of the stabilizing effects of solutes, moderate doses of Fe(VI) added to natural waters at pH 7.5 resulted in exposures that have been shown to be effective for inactivation of target pathogens. Preformed ferric hydroxide was less effective than freshly dosed ferric chloride in accelerating Fe(VI) decomposition.

  15. Biogenic sulfides for sequestration of Cr (VI, COD and sulfate from synthetic wastewater

    Directory of Open Access Journals (Sweden)

    Anamika Verma

    2015-04-01

    Full Text Available The aim of this work is to explore the possibility of using mixed culture of mesophilic sulfate-reducing bacteria (SRB for retrieval of toxic and carcinogenic Cr (VI from synthetic solution. In order to treat Cr (VI containing wastewater effectively, SRB culture was adapted to 50 mg/L Cr (VI and maintained through repeated sub-culturing to enhance the growth and activity of SRB. Batch biosorption experiments were carried out in glass serum vials by cultured SRB, accomplishing the removal of 82.1% Cr (VI, 76.9% sulfate, 85.7% COD under the following optimized conditions: pH 7, hydraulic retention time (HRT 7 days, temperature 37 °C and initial Cr (VI concentration of 50 mg/L. Further sorption experiments were conducted on synthetic wastewater under optimal operational conditions and resulted in 89.2% Cr (VI, 81.9% COD and 95.3% sulfate reduction from simulated wastewater. The results of this work contributed to a better understanding of metal uptake by biogenic sulfides and would be beneficial in the development of potential biosorbents that possess high capacities for Cr (VI uptake from aqueous environments.

  16. Adsorption of Uranyl Ions at the Nano-hydroxyapatite and Its Modification.

    Science.gov (United States)

    Skwarek, Ewa; Gładysz-Płaska, Agnieszka; Bolbukh, Yuliia

    2017-12-01

    Nano-hydroxyapatite and its modification, hydroxyapatite with the excess of phosphorus (P-HAP) and hydroxyapatite with the carbon ions built into the structure (C-HAP), were prepared by the wet method. They were studied by means of XRD, accelerated surface area and porosimetry (ASAP), and SEM. The size of crystallites computed using the Scherrer method was nano-hydroxyapatite (HAP) = 20 nm; P-HAP-impossible to determine; C-HAP = 22 nm; nano-HAP/U(VI) = 13.7 nm; P-HAP/U(VI)-impossible to determine, C-HAP/U(VI) = 11 nm. There were determined basic parameters characterizing the double electrical layer at the nano-HAP/electrolyte and P-HAP/electrolyte, C-HAP/electrolyte inter faces: density of the surface charge and zeta potential. The adsorption properties of nano-HAP sorbent in relation to U(VI) ions were studied by the batch technique. The adsorption processes were rapid in the first 60 min and reached the equilibrium within approximately 120 min (for P-HAP) and 300 min (for C-HAP and nano-HAP). The adsorption process fitted well with the pseudo-second-order kinetics. The Freundlich, Langmuir-Freundlich, and Dubinin-Radushkevich models of isotherms were examined for their ability to the equilibrium sorption data. The maximum adsorption capabilities (q m ) were 7.75 g/g for P-HAP, 1.77 g/g for C-HAP, and 0.8 g/g for HAP at 293 K.

  17. Effect of glutamic acid on copper sorption onto kaolinite - Batch experiments and surface complexation modeling.

    Science.gov (United States)

    Karimzadeh, Lotfollah; Barthen, Robert; Stockmann, Madlen; Gruendig, Marion; Franke, Karsten; Lippmann-Pipke, Johanna

    2017-07-01

    High carbonate content of the European Kupferschiefer ore deposits is a challenge for acid copper leaching (pH ≤ 2). Therefore investigating the mobility behavior of Cu(II) under conditions related to an alternative, neutrophil biohydrometallurgical Cu(II) leaching approach is of interest. As glutamic acid (Glu) might be present as a component in the growth media, we studied its effects on the adsorption of Cu(II) onto kaolinite. The binary and ternary batch sorption measurements of Cu(II) and Glu onto kaolinite were performed in the presence of 10 mM NaClO 4 as background electrolyte and at a pH range from 4 to 9. Sorption experiments were modeled by the charge-distribution multi-site ion complexation (CD-MUSIC) model by using single sorption site (≡SOH) and monodentate surface complexation reactions. Glu sorption on kaolinite is weak (copper mobility. The results of isotherms show that Cu(II)-Glu sorption onto kaolinite mimics the Freundlich model. The proposed CD-MUSIC model provides a close fit to the experimental data and predicts the sorption of Cu(II), Cu(II)-Glu and Glu onto kaolinite as well as the effect of Glu on Cu(II) mobility. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Acid-activated spent bleaching earth as a sorbent for chromium (VI) in aqueous solution.

    Science.gov (United States)

    Low, K S; Lee, C K; Lee, T S

    2003-02-01

    Spent bleaching earth, an industrial waste produced after the bleaching of crude palm oil, was investigated for its potential in removing Cr(VI) from aqueous solution. The earth was treated with different amounts of sulfuric acid and under different activation temperatures. Results show that the optimum treatment process involved 10% sulfuric acid at 350 degrees C. The effects of contact time, pH, initial concentration, sorbent dosage, temperature, sorption isotherms and the presence of other anions on its sorption capacity were studied. Isotherm data could be fitted into a modified Langmuir isotherm model implying monolayer coverage of Cr(VI) on acid activated spent bleaching earth. The maximum sorption capacity derived from the Langmuir isotherm was 21.2 mg g(-1). This value was compared with those of some other low cost sorbents. Studies of anion effect on the uptake of Cr(VI) on acid activated spent bleaching earth provided the following order of suppression: EDTA >PO4(3-)>SO4(2-)>NO3(-)>Cl(-).

  19. Phenanthrene Sorption on Biochar-Amended Soils

    DEFF Research Database (Denmark)

    Kumari, K. G I D; Moldrup, Per; Paradelo, Marcos

    2014-01-01

    on their influences on the sorption of environmental contaminants. In a field-based study at two experimental sites in Denmark, we investigated the effect of birch wood-derived biochar (Skogans kol) on the sorption of phenanthrene in soils with different properties. The soil sorption coefficient, Kd (L kg-1......), of phenanthrene was measured on sandy loam and loamy sand soils which have received from zero up to 100 t ha-1 of biochar. Results show that birch wood biochar had a higher Kd compared to soils. Furthermore, the application of birch wood biochar enhanced the sorption of phenanthrene in agricultural soils...

  20. Moisture sorption in naturally coloured cotton fibres

    Science.gov (United States)

    Ceylan, Ö.; De Clerck, K.

    2017-10-01

    Increasing environmental concerns have stimulated an interest in naturally coloured cottons. As many commercial and technical performance aspects of cotton fibres are influenced by their response towards atmospheric humidity, an in-depth research on moisture sorption behaviour of these fibres using dynamic vapour sorption is carried out. Significant differences were observed in sorption capacity and hysteresis behaviour of brown and green cotton fibres. These differences are mainly attributed to the variations in maturity and crystallinity index of the fibres. This study provides valuable insights into the moisture sorption behaviour of naturally coloured cotton fibres.

  1. Influence of pig manure biochar mineral content on Cr(III) sorption capacity

    DEFF Research Database (Denmark)

    Wnetrzak, Renata; Leahy, J.J.; Chojnacka, Katarzyna W.

    2014-01-01

    BACKGROUND: The adsorption of Cr(III) ions on various pig manure biochar (BC) samples was investigated to determine the effect of operating conditions (initial pH, sorbate and sorbent concentrations) on sorptive capacity. The BC samples with higher sorption capacity showed high surface area...

  2. Influence of humic fulvic acid on the sorption behaviour of Eu(III) on natural hematite

    Energy Technology Data Exchange (ETDEWEB)

    Rabung, T. [Universitaet des Saarlandes, Saarbruecken (Germany). Anorganische und Analytische Chemie und Radiochemie]|[Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Nukleare Entsorgungstechnik; Geckeis, H.; Kim, J.I. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Nukleare Entsorgungstechnik; Beck, H.P. [Universitaet des Saarlandes, Saarbruecken (Germany). Anorganische und Analytische Chemie und Radiochemie

    1999-04-01

    The solid-water interface reaction is investigated for the sorption of the Eu(III) ion, as a trivalent actinide homologue, onto well-characterized natural hematite at pH{<=}6 in 0.1 M NaClO{sub 4} in the presence of humic and fulvic acid (HA/FA). (orig.)

  3. Investigation of U(VI) adsorption in quartz-chlorite mineral mixtures.

    Science.gov (United States)

    Wang, Zheming; Zachara, John M; Shang, Jianying; Jeon, Choong; Liu, Juan; Liu, Chongxuan

    2014-07-15

    A batch and cryogenic laser-induced time-resolved luminescence spectroscopy investigation of U(VI) adsorbed on quartz-chlorite mixtures with variable mass ratios have been performed under field-relevant uranium concentrations (5×10(-7) M and 5×10(-6) M) in pH 8.1 synthetic groundwater. The U(VI) adsorption Kd values steadily increased as the mass fraction of chlorite increased, indicating preferential sorption to chlorite. For all mineral mixtures, U(VI) adsorption Kd values were lower than that calculated from the assumption of component additivity possibly caused by surface modifications stemming from chlorite dissolution; The largest deviation occurred when the mass fractions of the two minerals were equal. U(VI) adsorbed on quartz and chlorite displayed characteristic individual luminescence spectra that were not affected by mineral mixing. The spectra of U(VI) adsorbed within the mixtures could be simulated by one surface U(VI) species on quartz and two on chlorite. The luminescence intensity decreased in a nonlinear manner as the adsorbed U(VI) concentration increased with increasing chlorite mass fraction-likely due to ill-defined luminescence quenching by both structural Fe/Cr in chlorite, and trace amounts of solubilized and reprecipitated Fe/Cr in the aqueous phase. However, the fractional spectral intensities of U(VI) adsorbed on quartz and chlorite followed the same trend of fractional adsorbed U(VI) concentration in each mineral phase with approximate linear correlations, offering a method to estimate of U(VI) concentration distribution between the mineral components with luminescence spectroscopy.

  4. (VI) from water by micro-alloyed aluminium composite (MAlC)

    African Journals Online (AJOL)

    driniev

    2004-07-03

    Jul 3, 2004 ... This paper deals with Cr(VI) ion removal from water, by micro-alloyed aluminium composite (MAlC), under flow conditions. In a water environment the MAlC acts as a strong reducing agent. Dissolving it in water is accompanied by the generation of Al(III) ions and reduction of water to H2, with OH– ions.

  5. Valorisation of post-sorption materials: Opportunities, strategies, and challenges.

    Science.gov (United States)

    Harikishore Kumar Reddy, D; Vijayaraghavan, K; Kim, Jeong Ae; Yun, Yeoung-Sang

    2017-04-01

    Adsorption is a facile, economic, eco-friendly and low-energy requiring technology that aims to separate diverse compounds (ions and molecules) from one phase to another using a wide variety of adsorbent materials. To date, this technology has been used most often for removal/recovery of pollutants from aqueous solutions; however, emerging post-sorption technologies are now enabling the manufacture of value-added key adsorption products that can subsequently be used for (i) fertilizers, (ii) catalysis, (iii) carbonaceous metal nanoparticle synthesis, (iv) feed additives, and (v) biologically active compounds. These new strategies ensure the sustainable valorisation of post-sorption materials as an economically viable alternative to the engineering of other green chemical products because of the ecological affability, biocompatibility, and widespread accessibility of post-sorption materials. Fertilizers and feed additives manufactured using sorption technology contain elements such as N, P, Cu, Mn, and Zn, which improve soil fertility and provide essential nutrients to animals and humans. This green and effective approach to managing post-sorption materials is an important step in reaching the global goals of sustainability and healthy human nutrition. Post-sorbents have also been utilized for the harvesting of metal nanoparticles via modern catalytic pyrolysis techniques. The resulting materials exhibited a high surface area (>1000m(2)/g) and are further used as catalysts and adsorbents. Together with the above possibilities, energy production from post-sorbents is under exploration. Many of the vital 3E (energy, environment, and economy) problems can be addressed using post-sorption materials. In this review, we summarize a new generation of applications of post-adsorbents as value-added green chemical products. At the end of each section, scientific challenges, further opportunities, and issues related to toxicity are discussed. We believe this critical

  6. Selective removal of chromium (VI) from sulphates and other metal ...

    African Journals Online (AJOL)

    2011-10-06

    Oct 6, 2011 ... (Leonberg, Germany) equipped with a Lambda 1010 UV-Vis absorbance detector was ... AG 7 (4 x 50 mm) guard column and Dionex IonPac® AS7 (4 x. 250 mm) analytical ...... and equilibrium characterization of uranium(VI) adsorption onto .... netic nanoparticles in a polyvinylpyridine matrix. Polymer 41.

  7. Adsorption kinetics for the removal of chromium (VI) from aqueous ...

    African Journals Online (AJOL)

    A comparison of kinetic models applied to the adsorption of Cr(VI) ions on the adsorbents was evaluated for the pseudo first-order, the pseudo second-order, Elovich and intraparticle diffusion kinetic models, respectively. Results show that the pseudo second-order kinetic model was found to correlate the experimental data ...

  8. Spectroscopic studies on the interaction of U(VI) with Bacillus sphaericus

    Energy Technology Data Exchange (ETDEWEB)

    Panak, P.J.; Knopp, R.; Booth, C.H. [Lawrence Berkeley National Lab., The Glenn T. Seaborg Center, Berkeley, CA (United States); Nitsche, H. [Lawrence Berkeley National Lab., The Glenn T. Seaborg Center, Berkeley, CA (United States); Univ. of California at Berkeley, Dept. of Chemistry, Berkeley, CA (United States)

    2002-07-01

    We studied the interaction of U(VI) with vegetative cells, heat killed cells, spores, and decomposed cells of Bacillus sphaericus. The characterization of the formed complexes was performed by time-resolved laser fluorescence spectroscopy (TRLFS) and extended X-ray absorption fine structure spectroscopy (EXAFS). We observed no significant differences in the sorption behavior of vegetative and heat killed cells, whereas the spores showed a higher sorption of U(VI) (related to their dry weight). Regardless of the higher relative sorption of the spores of B. sphaericus, the fluorescence and EXAFS spectra of the vegetative cells, heat killed cells and spores were almost identical. Analysis of the data proved that U(VI) forms inner sphere complexes with organic bound phosphate groups on the cell surface. We observed no significant differences in the coordination numbers and the distances of the oxygen and phosphorus atoms in the inner coordination sphere. After eight weeks, the vegetative cells of B. sphaericus were completely decomposed. Lysing of the cell walls and activity of enzymes led to a release of various decomposition products. We found that large amounts of H{sub 2}PO{sub 4}{sup -} were released which caused a quantitative precipitation of bacterial U(VI) as UO{sub 2}(H{sub 2}PO{sub 4}){sub 2}. The H{sub 2}PO{sub 4}{sup -} was detected by Raman spectroscopy. The decomposed bacterial suspension showed the same fluorescence spectrum as UO{sub 2}(H{sub 2}PO{sub 4}){sub 2} which differed significantly from those of the bacterial U(VI) surface complexes. (orig.)

  9. Understanding the sorption behavior of Pu{sup 4+} on poly(amidoamine) dendrimer functionalized carbon nanotube. Sorption equilibrium, mechanism, kinetics, radiolytic stability, and back-extraction studies

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Parveen [Indian Institute of Technology, Himachal Pradesh (India); Sengupta, Arijit [Bahbha Atomic Research Centre, Mumbai (India). Radiochemistry Div.; Deb, Ashish Kumar Singha; Ali, S. Musharaf [Bahbha Atomic Research Centre, Mumbai (India). Chemical Engineering Div.; Homi Bhabha National Institute, Mumbai (India); Dasgupta, Kinshuk [Bhabha National Institute, Mumbai (India). Mechanical Metallurgy Div.

    2017-07-01

    Poly(amidoamine) dendrimer functionalized carbon nanotube was demonstrated as highly efficient sorbent of the Pu{sup 4+} from radioactive waste solution. The second generation dendrimer was found to have more efficiency as compared to the 1{sup st} generation might be due to the availability of more functionality for coordinating to the Pu{sup 4+} ion. Analysis of different isotherm models revealed that, Langmuir isotherm was predominantly operating through chemi-sorption (with the sorption energy 10.07 and 16.95 kJ mol{sup -1} for 1{sup st} and 2{sup nd} generation dendrimer) with the sorption capacity 89.22 mg g{sup -1} and 92.48 mg g{sup -1} for 1{sup st} and 2{sup nd} generation dendrimer, respectively. Analysis of different sorption kinetics model revealed that the sorption proceeded via pseudo 2{sup nd} order reaction. The 2{sup nd} generation dendrimer was found to be radiolytically more stable while oxalic acid was found to be suitable for quantitative back extraction of Pu{sup 4+}.

  10. Sorption and desorption of chromate by wood shavings impregnated with iron or aluminum oxide.

    Science.gov (United States)

    Kuo, S; Bembenek, R

    2008-09-01

    This study examined the impregnation of hybrid poplar shavings with Fe or Al oxide and their reactivity with Cr(VI). The shavings were impregnated with an average of 1.24+/-0.18 mmol Fe g(-1) or 1.51+/-0.17 mmol Al g(-1), and the impregnated Fe or Al oxide was highly amorphous. Capacity of Cr(VI) sorption by impregnated shavings was high and rate of the sorption was rapid. While the freshly sorbed Cr on the Fe oxide-shavings was readily desorbed in 0.1M NaOH, nine weeks of ageing reduced the desorbability to only 6.5% of the sorbed Cr. Extraction with 0.1M NaOH remained feasible to recover most sorbed Cr from the Al oxide-shavings over the same ageing period. Impregnation of the shavings with Fe or Al oxide turns the wood waste into a product for removing Cr(VI) or other oxyanions from wastewater.

  11. Vi tror, vi forstår hinanden, men det gør vi ikke

    DEFF Research Database (Denmark)

    Boysen, Mikkel Snorre Wilms

    2016-01-01

    Vores verdensbillede er baseret på en tro på, at vi forstår hinanden. Men meget tyder på, at denne tro snarere er en illusion. Derfor må vi indstille os på, at der skal en særlig indsats til, hvis vi skal kunne forstå vores omverden og menneskene i den......Vores verdensbillede er baseret på en tro på, at vi forstår hinanden. Men meget tyder på, at denne tro snarere er en illusion. Derfor må vi indstille os på, at der skal en særlig indsats til, hvis vi skal kunne forstå vores omverden og menneskene i den...

  12. Focused Ion Beam Analysis of Banana Peel and Its Application for Arsenate Ion Removal

    Directory of Open Access Journals (Sweden)

    Jamil R. Memon

    2015-06-01

    Full Text Available Banana peel, a common fruit waste, has been investigated for its ability to remove arsenate ions from ground water as a function of pH, contact time, and initial metal ion concentration. Focused ion beam (FIB analysis revealed the internal morphology of the banana peels. Arsenate ions were entered into micropores of banana peel. pH was seen to have no effect on the sorption process. Retained species were eluted using 5 mL of 2 M H2SO4. The kinetics of sorption were observed to follow the pseudo first order rate equation. The sorption data followed Freundlich and D-R isotherms. The energy value obtained from the D-R isotherms indicated that the sorption was physical in nature for arsenate species. Our study has shown that banana peel has the ability to remove arsenate species from ground water samples.

  13. Sorption of cesium and strontium from concentrated brines by backfill barrier materials

    Energy Technology Data Exchange (ETDEWEB)

    Winslow, C D

    1981-03-01

    The sorption of radionuclides from potentially intruding groundwater at a nuclear waste repository is a major chemical function of backfill barriers. In this study, various materials (including clays, zeolites and an inorganic ion exchanger) were screened for the sorption of the fission products cesium and strontium in concentrated brines. Representative brines A and B for the Waste Isolation Pilot Plant (WIPP), a proposed radioactive waste repository and test facility in bedded salt were used. Sorption properties were quantified using empirical distribution coefficients, k/sub d/. Of the materials examined, sodium titanate had the highest k/sub d/ for the sorption of Sr(II) in both brine A (k/sub d/ = 125 ml/g) and brine B(k/sub d/ = 500 to 600 ml/g). A mordenite-type zeolite was the most effective getter for Cs(I) in brine A (k/sub d = 27 ml/g), while illite yielded the highest k/sub d/ for Cs(I) in brine B (k/sub d/ = 115 ml/g). The relative merit of these k/sub d/ values is evaluated in terms of calculated estimates of breakthrough times for a backfill barrier containing the getter. Results show that a backfill mixture containing these getters is potentially an effective barrier to the migration of Sr(II) and Cs(I), although further study (especially for the sorption of cesium from brine A) is recommended. Initial mechanistic studies revealed competing ion effects which would support an ion exchange mechanism. K/sub d/'s were constant over a Sr(II) concentration range of 10/sup -11/ to 10/sup -5/ M and a Cs(I) concentration range of 10/sup -8/ to 10/sup -5/ M, supporting the choice of a linear sorption isotherm as a model for the results. Constant batch composition was shown to be attained within one week.

  14. Regenerative sorption compressors for cryogenic refrigeration

    Science.gov (United States)

    Bard, Steven; Jones, Jack A.

    Dramatic efficiency improvements for sorption coolers appear possible with use of compressor heat regeneration techniques. The general theory of sorption compressor heat regeneration is discussed in this paper, and several design concepts are presented. These designs result in long-life, low-vibration cryocoolers that potentially have efficiencies comparable to Stirling refrigerators for 65 to 90 K spacecraft instrument cooling applications.

  15. Phosphorus sorption isotherms and external phosphorus ...

    African Journals Online (AJOL)

    Information on P sorption characteristics of soils is important for making profitable P fertiliser recommendations and designing appropriate P management strategies for improving crop productivity. An experiment was conducted to determine the P sorption capacities and external P requirements (EPR) of some soils of ...

  16. Predicting Organic Cation Sorption Coefficients: Accounting for Competition from Sorbed Inorganic Cations Using a Simple Probe Molecule.

    Science.gov (United States)

    Jolin, William C; Goyetche, Reaha; Carter, Katherine; Medina, John; Vasudevan, Dharni; MacKay, Allison A

    2017-06-06

    With the increasing number of emerging contaminants that are cationic at environmentally relevant pH values, there is a need for robust predictive models of organic cation sorption coefficients (Kd). Current predictive models fail to account for the differences in the identity, abundance, and affinity of surface-associated inorganic exchange ions naturally present at negatively charged receptor sites on environmental solids. To better understand how organic cation sorption is influenced by surface-associated inorganic exchange ions, sorption coefficients of 10 organic cations (including eight pharmaceuticals and two simple probe organic amines) were determined for six homoionic forms of the aluminosilicate mineral, montmorillonite. Organic cation sorption coefficients exhibited consistent trends for all compounds across the various homoionic clays with sorption coefficients (Kd) decreasing as follows: KdNa+ > KdNH4+ ≥ KdK+ > KdCa2+ ≥ KdMg2+ > KdAl3+. This trend for competition between organic cations and exchangeable inorganic cations is consistent with the inorganic cation selectivity sequence, determined for exchange between inorganic ions. Such consistent trends in competition between organic and inorganic cations suggested that a simple probe cation, such as phenyltrimethylammonium or benzylamine, could capture soil-to-soil variations in native inorganic cation identity and abundance for the prediction of organic cation sorption to soils and soil minerals. Indeed, sorption of two pharmaceutical compounds to 30 soils was better described by phenyltrimethylammonium sorption than by measures of benzylamine sorption, effective cation exchange capacity alone, or a model from the literature (Droge, S., and Goss, K. Environ. Sci. Technol. 2013, 47, 14224). A hybrid approach integrating structural scaling factors derived from this literature model of organic cation sorption, along with phenyltrimethylammonium Kd values, allowed for estimation of Kd values for more

  17. Cinética e equilíbrio de adsorção dos oxiânions Cr (VI, Mo (VI e Se (VI pelo sal de amônio quaternário de quitosana Kinetics and equilibrium of adsorption of oxyanions Cr (VI, Mo (VI and Se (VI by quaternary ammonium chitosan salt

    Directory of Open Access Journals (Sweden)

    Viviane A. Spinelli

    2005-07-01

    one gram of cross-linked quaternary chitosan salt adsorbed 68.3 mg of chromium, 63.4 mg of molybdenum and 90.0 mg of selenium. The adsorption process followed a pseudo second-order kinetic rate equation and the equilibrium regarding the three ions was reached after 200 minutes. The studies from X-ray dispersive energy showed that the main adsorption mechanism is ionic exchange among Cl- groups on the polymer surface by oxyanions from solution and the anionic exchanger showed the following selectivity order: Cr (VI > Mo (VI > Se (VI.

  18. Long Term Sorption Diffusion Experiment (LTDE-SD). Performance of main in situ experiment and results from water phase measurements

    Energy Technology Data Exchange (ETDEWEB)

    Widestrand, Henrik; Byegaard, Johan; Nilsson, Kersti; Hoeglund, Susanne; Gustafsson, Erik (Geosigma AB, Uppsala (Sweden)); Kronberg, Magnus (Swedish Nuclear Fuel and Waste Management Co. (Sweden))

    2010-12-15

    The LTDE-SD experiment, (Long Term Sorption Diffusion Experiment) aimed at increasing the scientific knowledge of sorption and diffusion under in situ conditions and to provide data for performance and safety assessment calculations. Performance and results of the in situ experiment phase are presented in the report. In total, 21 radionuclide trace elements and one stable trace element were injected, circulated and sampled for approx6.5 months in a closed borehole section. The trace elements represented non-sorbing tracers and sorbing tracers for which the sorption was dominated by a cation exchange mechanism, a surface complexation mechanism, or dependent on an electrochemical reduction in order to reach the tetravalent state (oxidation state IV) considered very strongly sorbing. The borehole section in contact with the tracer labelled groundwater consisted in part of a natural fracture surface and a borehole section in the unaltered matrix rock, devoid of natural fractures. Water samples were regularly extracted and analysed for trace element concentration and a few ion exchange speciation and filtered samplings were also conducted. Independent colloid filtering and chemical speciation calculations were performed in support the evaluation. Sorption was demonstrated for a series of elements present in the experiment. The amounts lost of the different respective tracers from the aqueous phase follow very well the general understanding of the relative sorption strength of the tracers, as inferred from e.g. batch sorption experiments and dynamic in situ tracer experiments. The chemical speciation calculations of the different tracers were in line with the results of the ion exchange speciation performed during the experiment. With the exception of UO{sub 2} 2+ carbonate complexes formed, no strong indications were obtained that aqueous complexation prevents adsorption under the chemical conditions of the experiment. The 20 nm filtered sampling indicated that

  19. Adsorption Properties of Bentonite with In Situ Immobilized Polyaniline Towards Anionic Forms of Cr(VI, Mo(VI, W(VI, V(V

    Directory of Open Access Journals (Sweden)

    Kateryna RYABCHENKO

    2016-05-01

    Full Text Available A new composite material bentonite-PANI was synthesized by in situ immobilization of polyaniline (PANI on the surface of natural mineral bentonite. It was established as a result of the modification of bentonite a surface area and an interlayer distance of mineral decrease and particles of bentonite transformed of irregular shape with different porosity on irregularly shaped particles of smaller size. It has been found that the total Cr(VI ions extraction took place under the acid conditions (pH=1 – 2 and W(VI ions have been well adsorbed in the pH range from 1 to 8 by the composite bentonite-PANI unlike the initial mineral. Whereas adsorption of oxo anions of V(V and Mo(VI made up some 50%. It is proved that the in situ immobilization of bentonite by polyaniline leads to increasing the value of adsorption capacity towards the investigated ions compared with the initial mineral. It was established that the adsorption properties of the synthesized composite with respect to the studied oxo ions were worse than the adsorption properties of composite vermiculite-PANI, similar to the composite Sokyryntsyy clinoptilolite-PANI and better than composites of polyaniline with Podilskyy saponite and Karelian shungite.DOI: http://dx.doi.org/10.5755/j01.ms.22.2.6976

  20. Investigation of uranium (VI) adsorption by polypyrrole.

    Science.gov (United States)

    Abdi, S; Nasiri, M; Mesbahi, A; Khani, M H

    2017-06-15

    The purpose of this study was to investigate the adsorption of uranium (VI) ions on the polypyrrole adsorbent. Polypyrrole was synthesized by a chemical method using polyethylene glycol, sodium dodecylbenzenesulfonate, and cetyltrimethylammonium bromide as the surfactant and iron (III) chloride as an oxidant in the aqueous solution. The effect of various surfactants on the synthesized polymers and their performance as the uranium adsorbent were investigated. Adsorbent properties were characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) techniques. The effect of different parameters such as pH, contact time, initial metal ion concentrations, adsorbent dose, and the temperature was investigated in the batch system for uranium adsorption process. It has been illustrated that the adsorption equilibrium time is 7min. The results showed that the Freundlich model had the best agreement and the maximum adsorption capacity of polypyrrole for uranium (VI) was determined 87.72mg/g from Langmuir isotherm. In addition, the mentioned adsorption process was fast and the kinetic data were fitted to the Pseudo first and second order models. The adsorption kinetic data followed the pseudo-second-order kinetic model. Moreover, the thermodynamic parameters ΔG(0), ΔH(0) and ΔS(0) showed that the uranium adsorption process by polypyrrole was endothermic and spontaneous. Copyright © 2017. Published by Elsevier B.V.

  1. Assessment of metal sorption mechanisms by aquatic macrophytes using PIXE analysis

    Energy Technology Data Exchange (ETDEWEB)

    Módenes, A.N., E-mail: anmodenes@yahoo.com.br [Department of Chemical Engineering-Postgraduate Program, West Parana State University, Campus of Toledo, rua da Faculdade 645, Jd. La Salle, 85903-000 Toledo, PR (Brazil); Espinoza-Quiñones, F.R.; Santos, G.H.F.; Borba, C.E. [Department of Chemical Engineering-Postgraduate Program, West Parana State University, Campus of Toledo, rua da Faculdade 645, Jd. La Salle, 85903-000 Toledo, PR (Brazil); Rizzutto, M.A. [Physics Institute, University of São Paulo, Rua do Matão s/n, Travessa R 187, 05508-900 São Paulo, SP (Brazil)

    2013-10-15

    Highlights: • Divalent metal ion removals by Egeria densa biosorbent. • Multielements concentrations in biosorbent samples by PIXE analysis. • Elements mass balance in liquid and solid phase before and after metal removals. • Assessment of the mechanisms involved in Cd{sup 2+} and Zn{sup 2+} removal by biosorbent. • Confirmation of the signature of ion exchange process in metal removal. -- Abstract: In this work, a study of the metal sorption mechanism by dead biomass has been performed. All batch metal biosorption experiments were performed using the aquatic macrophyte Egeria densa as biosorbent. Divalent cadmium and zinc solutions were used to assess the sorption mechanisms involved. Using a suitable equilibrium time of 2 h and a mixture of 300 mg biosorbent and 50 mL metal solution at pH 5, monocomponent sorption experiments were performed. In order to determine the residual amounts of metals in the aqueous solutions and the concentrations of removed metals in the dry biomass, Particle Induced X-ray Emission (PIXE) measurements in thin and thick target samples were carried out. Based on the strong experimental evidence from the mass balance among the major elements participating in the sorption processes, an ion exchange process was identified as the mechanism responsible for metal removal by the dry biomass.

  2. Ex-situ bioremediation of U(VI from contaminated mine water using Acidithiobacillus ferrooxidans strains

    Directory of Open Access Journals (Sweden)

    Maria eRomero-Gonzalez

    2016-05-01

    Full Text Available The ex-situ bioremoval of U(VI from contaminated water using Acidithiobacillus ferrooxidans strain 8455 and 13538 was studied under a range of pH and uranium concentrations. The effect of pH on the growth of bacteria was evaluated across the range 1.5 – 4.5 pH units. The respiration rate of At. ferrooxidans at different U(VI concentrations was quantified as a measure of the rate of metabolic activity over time using an oxygen electrode. The biosorption process was quantified using a uranyl nitrate solution, U-spiked growth media and U-contaminated mine water. The results showed that both strains of At. ferrooxidans are able to remove U(VI from solution at pH 2.5 – 4.5, exhibiting a buffering capacity at pH 3.5. The respiration rate of the micro-organism was affected at U(VI concentration of 30 mg L-1. The kinetics of the sorption fitted a pseudo-first order equation, and depended on the concentration of U(VI. The KD obtained from the biosorption experiments indicated that strain 8455 is more efficient for the removal of U(VI. A bioreactor designed to treat a solution of 100 mg U(VI L-1 removed at least 50% of the U(VI in water. The study demonstrated that At. ferrooxidans can be used for the ex-situ bioremediation of U(VI contaminated mine water.

  3. A study of sorption of cadmium by goethite in aqueous solution

    Directory of Open Access Journals (Sweden)

    N. Salami

    2002-06-01

    Full Text Available Investigation has been carried out on the potential of a locally sourced goethite for the removal of cadmium ion from aqueous solutions using batch equilibration technique. The maximum uptake of cadmium is 6.4  10-2 mg/g-goethite. The sorption kinetics appears to be rapid as equilibrium was attained within a period of 1 hour. The highest sorption capacity was obtained for particle size with diameter (Φ 0.09 mm. Both infrared spectrophotometric and X-ray diffraction (XRD techniques have also provided evidence for cadmium fixation on to the surface of the goethite. The sorption mechanism appears to follow Langmuir adsorption isotherm model. The Langmuir constants K and Xm (mass of Cd2+ required to form monolayer on the entire surface of the goethite were 0.096 mg/g-goethite and 0.075 mg/g-goethite, respectively.

  4. Support vector regression model for predicting the sorption capacity of lead (II

    Directory of Open Access Journals (Sweden)

    Nusrat Parveen

    2016-09-01

    Full Text Available Biosorption is supposed to be an economical process for the treatment of wastewater containing heavy metals like lead (II. In this research paper, the support vector regression (SVR has been used to predict the sorption capacity of lead (II ions with the independent input parameters being: initial lead ion concentration, pH, temperature and contact time. Tree fern, an agricultural by-product, has been employed as a low cost biosorbent. Comparison between multiple linear regression (MLR and SVR-based models has been made using statistical parameters. It has been found that the SVR model is more accurate and generalized for prediction of the sorption capacity of lead (II ions.

  5. The influence of salting out on the sorption of neutral organic compounds in estuaries.

    Science.gov (United States)

    Turner, A; Rawling, M C

    2001-12-01

    The relative (unsaturated) solubility and sorption of 2,2',5,5'-tetrachlorobiphenyl have been studied along an estuarine salinity gradient. The aqueous compound was salted out with increasing salinity and an aqueous salting constant of about 0.0021 g(-1) was derived. Sorption of the compound to estuarine particles increased with increasing salinity for a range of particle concentrations, but the magnitude of this effect (sorption salting constants of about 0.005-0.011 g(-1)) indicated that salting out of the aqueous phase was not solely responsible. It is suggested that the hydrophobicity of sediment organic matter is enhanced by its interaction with seawater ions through a reduction in the charge of the particle surface and, possibly, modification of the structure of the organic matter. Examination of literature data on the sorption of neutral organic compounds to estuarine sediment indicates a general increase in sorption with increasing salinity which can be empirically defined by a salting equation. Although charge reduction of estuarine particles is a general observation, it is not possible to establish the general significance of this effect (or any other form of salting out of sediment organic matter) on the sorption of organic compounds in estuaries because appropriate site- and compound-specific aqueous salting constants are unavailable. Increased sorption at high salinities has obvious implications for the disposal and transport of organic chemicals in estuaries. However, the inverse dependency of sediment-water partitioning on particle concentration is likely to be of at least equal significance in macrotidal environments where sediment resuspension occurs. An empirical model, combining the effects of salinity and particle concentration, is proposed for deriving first-order estimates of the partitioning of neutral organic compounds in estuaries.

  6. Determination of {sup 60}Co sorption in natural clinoptilolite; Determinacion de la sorcion de {sup 60}Co en clinoptilolita natural

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez B, E.; Granados C, F. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1997-07-01

    It was studied the clinoptilolite behavior coming from a deposit in Taxco, Guerrero in hydration and stabilization conditions with sodium for determining its sorption properties. The ion exchange process was carried out through gamma spectrometry using a CoCl{sub 2} solution marked with {sup 60} Co at p H 6.5 in different contact times. It was observed a maximum sorption of 0.408 m eq Co{sup +2}/g mineral, from 0.314 m eq Co{sup +2}/g mineral correspond at ion exchange. (Author)

  7. Diametral tensile strength and water sorption of glass-ionomer cements used in Atraumatic Restorative Treatment Resistência à tração diametral e sorção de água de cimentos de ionômero de vidro usados no Tratamento Restaurador Atraumático

    Directory of Open Access Journals (Sweden)

    Daniela Francisca Gigo Cefaly

    2003-06-01

    Full Text Available The purposes of this study were to evaluate the diametral tensile strength and the water sorption of restorative (Fuji IX and Ketac Molar and resin-modified glass-ionomer luting cements (ProTec Cem, Fuji Plus and Vitremer mixed at both manufacturer and increased powder: liquid ratio, for their use in the Atraumatic Restorative Treatment. A conventional restorative glass-ionomer (Ketac Fil was used as control. Specimens (6.0 mm in diameter x 3.0 mm in height were prepared and stored (1 hour, 1 day and 1 week for a diametral tensile strength test. Data were subjected to two-way ANOVA and Tukey tests (pAvaliou-se a resistência à tração diametral e a sorção de água de cimentos de ionômero de vidro restauradores (Fuji IX e Ketac Molar e modificados por resina indicados para cimentação (ProTec Cem, Fuji Plus e Vitremer manipulados na proporção pó: líquido indicada pelo fabricante e em maior proporção para a utilização no Tratamento Restaurador Atraumático. O ionômero restaurador convencional (Ketac Fil foi utilizado como controle. Espécimes (6,0 mm de diâmetro x 3,0 mm de altura foram preparados e armazenados (1 hora, 1 dia e 1 semana para o teste de resistência à tração diametral. Os dados foram submetidos a ANOVA a dois critérios e ao teste de Tukey (p<0,05. Para o teste de sorção de água, espécimes com 15,0 mm de diâmetro x 0,5 mm de altura foram preparados e transferidos a dessecadores até a obtenção de uma massa constante. Em seguida, os espécimes foram imersos em água deionizada por 7 dias, pesados e recondicionados a uma massa constante em dessecadores. Os dados foram submetidos a ANOVA a um critério e ao teste de Tukey (p<0,05. Cinco espécimes de cada material e consistência foram preparados para cada teste. Os ionômeros modificados por resina mostraram maior resistência que os convencionais. Exceto pelo ProTec Cem, a resistência dos materiais modificados por resina significativamente aumentou da

  8. Sorption of methylxanthines by different sorbents

    Science.gov (United States)

    Dmitrienko, S. G.; Andreeva, E. Yu.; Tolmacheva, V. V.; Terent'eva, E. A.

    2013-05-01

    Sorption of caffeine, theophylline, theobromine, diprophylline, and pentoxyphylline on different sorbents (supercross-linked polystyrene, surface-modified copolymer of styrene and divinylbenzene Strata-X, and carbon nanomaterials Taunit and Diasorb-100-C16T) was studied in a static mode in an effort to find new sorbents suitable for sorption isolation and concentration of methylxanthines. The peculiarities of sorption of methylxanthines were explained in relation to the solution acidity, the nature of the sorbates and their concentration, the nature of the solvent, and the structural characteristics of the sorbents.

  9. Examination of competitive lanthanide sorption onto smectites and its significance in the management of radioactive waste

    Energy Technology Data Exchange (ETDEWEB)

    Galunin, Evgeny [Departament de Quimica Analitica, Universitat de Barcelona, Marti i Franques 1-11, 08028 Barcelona (Spain); Alba, Maria D. [Instituto de Ciencia de Materiales de Sevilla, Consejo Superior de Investigaciones Cientificas - Universidad de Sevilla, Av. Americo Vespucio 49, 41092 Sevilla (Spain); Santos, Maria J. [Departamento de Quimica, Universidade Estadual de Londrina, Londrina, PR 86051-990 (Brazil); Abrao, Taufik [Instituto de Ciencia de Materiales de Sevilla, Consejo Superior de Investigaciones Cientificas - Universidad de Sevilla, Av. Americo Vespucio 49, 41092 Sevilla (Spain); Vidal, Miquel, E-mail: miquel.vidal@ub.edu [Departament de Quimica Analitica, Universitat de Barcelona, Marti i Franques 1-11, 08028 Barcelona (Spain)

    2011-02-28

    The competitive effect of La and Lu (analogues of radionuclides appearing in radioactive waste) in the sorption in four smectites was examined. Sorption and desorption distribution coefficients (K{sub d}; K{sub d,des}), and desorption rates (R{sub des}) were determined from batch tests in two media: deionized water and, to consider the influence of cement leachates, 0.02 mol L{sup -1} Ca. The competitive effect was lower when high-affinity sites were available, as in the water medium at the lowest range of initial lanthanide concentration, with high K{sub d} for La and for Lu (5-63 x 10{sup 4} L kg{sup -1}). Lower K{sub d} was measured at higher initial concentrations and in the Ca medium, where Lu showed a stronger competitive effect. This was confirmed by fitting the sorption data to a two-solute Langmuir isotherm. The desorption data indicated that sorption was virtually irreversible for the scenarios with high sorption, with an excellent correlation between K{sub d} and K{sub d,des} (R{sup 2} around 0.9 for the two lanthanides). Assuming that radioactive waste is a mixture of radionuclides, and that Ca ions will be provided by the cement leachates, this would reduce the retention capacity of clay engineered barriers.

  10. Equilibrium and kinetic studies of Pb(II, Cd(II and Zn(II sorption by Lagenaria vulgaris shell

    Directory of Open Access Journals (Sweden)

    Mitić-Stojanović Dragana-Linda

    2012-01-01

    Full Text Available The sorption of lead, cadmium and zinc ions from aqueous solution by Lagenaria vulgaris shell biosorbent (LVB in batch system was investigated. The effect of relevant parameters such as contact time, biosorbent dosage and initial metal ions concentration was evaluated. The Pb(II, Cd(II and Zn(II sorption equilibrium (when 98% of initial metal ions were sorbed was attained within 15, 20 and 25 min, respectively. The pseudo first, pseudo-second order, Chrastil’s and intra-particle diffusion models were used to describe the kinetic data. The experimental data fitted the pseudo-second order kinetic model and intra-particle diffusion model. Removal efficiency of lead(II, cadmium(II and zinc(II ions rapidly increased with increasing biosorbent dose from 0.5 to 8.0 g dm-3. Optimal biosorbent dose was set to 4.0 g dm-3. An increase in the initial metal concentration increases the sorption capacity. The sorption data of investigated metal ions are fitted to Langmuir, Freundlich and Temkin isotherm models. Langmuir model best fitted the equilibrium data (r2 > 0.99. Maximal sorption capacities of LVB for Pb(II, Cd(II and Zn(II at 25.0±0.5°C were 0.130, 0.103 and 0.098 mM g-1, respectively. The desorption experiments showed that the LVB could be reused for six cycles with a minimum loss of the initial sorption capacity.

  11. Photocatalytic Reduction of Aqueous Cr(VI) with CdS under Visible Light Irradiation: Effect of Particle Size

    OpenAIRE

    A. B. Makama; Ali Salmiaton; Elias B. Saion; T. S.Y. Choong; Abdullah, N.

    2017-01-01

    Stringent environmental standards have made the removal of Cr(VI) from water an important problem for environmental scientist and engineering. Heterogeneous photocatalysis using suspended photocatalyst is an interesting technique to consider for this application. In this work, the influence of particle size of suspended CdS on the photocatalytic reduction of aqueous Cr(VI) ion was investigated. The efficiency of Cr(VI) reduction was monitored through UV-visible analysis. The experimental resu...

  12. ViFiLite Project

    Data.gov (United States)

    National Aeronautics and Space Administration — ViFiLite is a wireless infrastructure that utilizes the advantages of a V-band technology in supporting data gathering for structural health monitoring as well as...

  13. Computer simulation of molecular sorption in zeolites

    CERN Document Server

    Calmiano, M D

    2001-01-01

    The work presented in this thesis encompasses the computer simulation of molecular sorption. In Chapter 1 we outline the aims and objectives of this work. Chapter 2 follows in which an introduction to sorption in zeolites is presented, with discussion of structure and properties of the main zeolites studied. Chapter 2 concludes with a description of the principles and theories of adsorption. In Chapter 3 we describe the methodology behind the work carried out in this thesis. In Chapter 4 we present our first computational study, that of the sorption of krypton in silicalite. We describe work carried out to investigate low energy sorption sites of krypton in silicalite where we observe krypton to preferentially sorb into straight and sinusoidal channels over channel intersections. We simulate single step type I adsorption isotherms and use molecular dynamics to study the diffusion of krypton and obtain division coefficients and the activation energy. We compare our results to previous experimental and computat...

  14. Powerful reactive sorption of silver(I) and mercury(II) onto poly(o-phenylenediamine) microparticles.

    Science.gov (United States)

    Li, Xin-Gui; Ma, Xiao-Li; Sun, Jin; Huang, Mei-Rong

    2009-02-03

    The strong adsorbability of Ag(I) and Hg(II) ions onto fine poly(o-phenylenediamine) (PoPD) microparticles synthesized through a chemically oxidative polymerization of o-phenylenediamine was systematically examined and PoPD/Ag nanocomposites were facilely prepared through the reactive sorption method. The effect of the (NH4)2S2O8 oxidant/o-phenylenediamine monomer ratio on the polymerization yield, macromolecular structure, conductivity, and insolubility of the PoPD microparticles was studied. The Ag(I) adsorbability of the microparticles was significantly optimized by varying the oxidant/monomer ratio, doping state, Ag(I) concentration, sorption time, and solution pH. The Ag(I) adsorbance steadily increases with changing oxidant/monomer molar ratio from 3/1 to 1/1, reaching up to the highest Ag(I) adsorbance of 533 mg.g(-1) at the oxidant/monomer ratio of 1/1. The sorption process fits the pseudosecond-order kinetics. The sorption is rapid because both the adsorbance and adsorptivity within 30 min reach up to 76% of the final values. The initial sorption rate of silver ions obtained from the pseudosecond-order equation is 12.9 mg.g(-1).min(-1). The highest adsorptivity of silver ions is up to 99.1%. The optimal solution pH for Ag(I) sorption is around 5.0. The sorption mechanism may include the chelation and redox reaction between Ag(I) ions and amine/imine groups on the PoPD chains. Similarly, the microparticles also have powerful Hg(II) adsorbability with 96.7% adsorptivity at an initial Hg(II) concentration of 4 mM. Competitive sorption between Ag(I) and Hg(II) in their mixture solution onto the microparticles was studied, exhibiting a preferential sorption toward Ag(I). The microparticles as a cost-effective sorbent demonstrate a promising application in the removal and even recovery of heavy-metal ions from wastewater. The PoPD/Ag nanocomposites possess (1) high Ag content of 34.8 wt %, (2) small diameter of Ag nanoparticles of around 10-20 nm, (3) narrow

  15. Chromium (VI removal from aqueous solutions using a polyethylenimine - epichlorohydrin resin

    Directory of Open Access Journals (Sweden)

    Sarri Sofia

    2016-01-01

    Full Text Available The ability of a synthesized polyethylenimine - epichlorohydrin resin to remove Cr(VI from aqueous solutions was investigated in absence (initial pH 2 to 7 and presence of background electrolytes (NaNO3 and Na2SO4 solutions of initial pH 3 and 6. The determined Cr-uptake was significantly higher than the one reported for the majority of other sorbents. The photo-metrically determined uptake data were modeled by the Langmuir, Redlich-Peterson, Langmuir-Freundlich, and Toth equations. The modeling results did not point out any preference to one specific model in terms of the goodness-of-fit and the prediction of maximum sorption capacity. The Cr-sorption kinetics was investigated at 15, 25, 35 and 45 oC using 51Cr-labeled solutions and γ-ray spectroscopy. The Cr-sorption was very fast at all studied temperatures and well reproduced by the pseudo-second order kinetics equation. Rate constant and activation energy values were calculated using the experimental data. The Cr-loaded resin was also examined by XRD, XPS, XAFS and SEM/EDS. The XPS and XAFS investigations indicated a partial reduction of Cr(VI to Cr(III. The environmental compatibility of the Cr-loaded resin was examined using the EPA-TCLP method. The Cr-binding by the resin was very stable and regeneration attempts by HCl solutions of pH 3 were rather unsuccessful.

  16. Biosorption of chromium (VI) onto NaOH activated Codium tomentosum biomass.

    Science.gov (United States)

    Palanisamy, Suresh Babu; Balaiah, Anandaraj

    2015-11-01

    Batch experiments were conducted to examine the efficacy of NaOH activated Codium tomentosum biomass on the sorption of hexavalent chromium. Several influencing parameters like pH, contact time, dosage and initial chromium(VI) concentration was experimented at 20°C. The monolayer sorption capacity was found to be 5.504 ± 0.360 mg g(-1). Langmuir and Freundlich isotherm implied favorable condition of chromium(VI) biosorption, based on R2 values. Dubinin-Radushkevich isotherm showed the best fit linearity and infered that adsorption energy as 4.888 ± 0.129 kJ mol(-1). Pseudo-second order kinetics showed good compliance for the entire data and the rate constant (k2) was found to be 0.0398 ± 0.007 g mg(-1) min. Elovich kinetics exhibited that adsorption occurs on heterogeneous surface. Intraparticle diffusion model specified multi-linearity in adsorption process. Hence, the employed biosorbent was sensible and sorption efficiency was remarkable.

  17. Skal vi have flere krondyr?

    DEFF Research Database (Denmark)

    Pedersen, Jens Christian

    2008-01-01

    Vi kunne have væsentligt flere krondyr i den danske natur end vi har i øjeblikket. Den primære årsag er jagt. Det viser en ny undersøgelse fra Danmarks Miljøundersøgelser ved Aarhus Universitet. Bestanden af krondyr er ganske vist steget meget siden 1970, men der er både plads og føde til mange...

  18. Equilibrium modeling of mono and binary sorption of Cu(II and Zn(II onto chitosan gel beads

    Directory of Open Access Journals (Sweden)

    Nastaj Józef

    2016-12-01

    Full Text Available The objective of the work are in-depth experimental studies of Cu(II and Zn(II ion removal on chitosan gel beads from both one- and two-component water solutions at the temperature of 303 K. The optimal process conditions such as: pH value, dose of sorbent and contact time were determined. Based on the optimal process conditions, equilibrium and kinetic studies were carried out. The maximum sorption capacities equaled: 191.25 mg/g and 142.88 mg/g for Cu(II and Zn(II ions respectively, when the sorbent dose was 10 g/L and the pH of a solution was 5.0 for both heavy metal ions. One-component sorption equilibrium data were successfully presented for six of the most useful three-parameter equilibrium models: Langmuir-Freundlich, Redlich-Peterson, Sips, Koble-Corrigan, Hill and Toth. Extended forms of Langmuir-Freundlich, Koble-Corrigan and Sips models were also well fitted to the two-component equilibrium data obtained for different ratios of concentrations of Cu(II and Zn(II ions (1:1, 1:2, 2:1. Experimental sorption data were described by two kinetic models of the pseudo-first and pseudo-second order. Furthermore, an attempt to explain the mechanisms of the divalent metal ion sorption process on chitosan gel beads was undertaken.

  19. Mechanisms of cesium sorption onto magnetite

    Energy Technology Data Exchange (ETDEWEB)

    Granizo, N.; Missana, T. [Environmental Impact of Energy Department. CIEMAT 28040 Madrid (Spain)

    2005-07-01

    Full text of publication follows: One of the current options for the final disposal of the high level radioactive waste is the deep geological repository. The radioactive waste canisters represent the first physical barrier to radionuclide migration to the geosphere and their corrosion products may play a significant role in sequestering radionuclide due to sorption and coprecipitation phenomena. In this work, the sorption of the fission product Cs-137 on magnetite, which is considered to be the main corrosion products under the reducing conditions expected in the repository, has been studied in a wide range of pH, ionic strength, radionuclide and sorbent concentration. The magnetite was synthesized in the laboratory and the main physico-chemical properties as microstructure, surface area and surface charge were analysed prior to sorption experiments. A measurable cesium sorption, generally never exceeding 20 %, was found only in alkaline conditions. Linear sorption isotherms were observed within the range of Cs concentration used (up to 10{sup -6} M). A slight increase in the sorption of cesium was seen when decreasing the ionic strength and increasing the pH, probably indicating the formation of outer sphere complexes. The possible effects on sorption of silicate impurities from the experimental vessels was deeply analysed and finally discarded. The experimental data have been satisfactorily modelled supposing the formation of a monodentate outer sphere complex and considering just one type of surface site on the magnetite. The combination of the structural information derived from XAS analysis, which is ongoing, together with wet chemistry sorption data will clarify the physical and chemical structure of sorbed complex and confirm the validity of surface complexation model proposed. (authors)

  20. Sorption of organophosphate esters by carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Wei; Yan, Li [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); Duan, Jinming [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Jing, Chuanyong, E-mail: cyjing@rcees.ac.cn [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China)

    2014-05-01

    Graphical abstract: The interfacial interactions between the OPE molecules and CNTs. - Highlights: • Oxygen-containing groups on CNTs change the sorption property for OPEs. • Molecular configuration of OPEs has insignificant impact on their sorption. • Hydrophobic, π–π EDA and Brønsted acid–base interaction occurred between the CNTs and OPEs. - Abstract: Insights from the molecular-level mechanism of sorption of organophosphate esters (OPEs) on carbon nanotubes (CNTs) can further our understanding of the fate and transport of OPEs in the environment. The motivation for our study was to explore the sorption process of OPEs on multi-walled CNTs (MWCNTs), single-walled CNTs (SWCNTs) and their oxidized counterparts (O-MWCNTs and O-SWCNTs), and its molecular mechanism over a wide concentration range. The sorption isotherm results revealed that the hydrophobicity of OPEs dominated their affinities on a given CNT and the π–π electron donor–acceptor (EDA) interaction also played an important role in the sorption of aromatic OPEs. This π–π EDA interaction, verified with Raman and FT-IR spectroscopy, could restrict the radial vibration of SWCNTs and affect the deformation vibration γ(CH) bands of OPE molecules. The OPE surface coverage on CNTs, estimated using the nonlinear Dubinin–Ashtakhov model, indicated that the oxygen-containing functional groups on CNTs could interact with water molecules by H-bonding, resulting in a decrease in effective sorption sites. In addition, FTIR analysis also confirmed the occurrence of Brønsted acid–base interactions between OPEs and surface OH groups of SWCNTs. Our results should provide mechanistic insights into the sorption mechanism of OPE contaminants on CNTs.

  1. Sorption characteristics of fluoride on to magnesium oxide-rich phases calcined at different temperatures.

    Science.gov (United States)

    Sasaki, Keiko; Fukumoto, Naoyuki; Moriyama, Sayo; Hirajima, Tsuyoshi

    2011-07-15

    The effect of calcination temperature during production of magnesium oxide-rich phases from MgCO(3) on the sorption of F(-) ions in the aqueous phase has been investigated. Magnesium oxide-rich phases were formed by calcination at over 873 K for 1h. Higher calcination temperatures produced more crystalline MgO with smaller specific surface area and provided larger values of the total basicity per unit surface area. The higher calcination temperatures lead to slower F(-) removal rate, and lower equilibrium F(-) concentrations, when the equilibrium F(-) concentrations are less than 1 mmol dm(-3). Larger total basicity per unit surface area made the reactivity with F(-) ions in aqueous phase more feasible, resulting in a greater degree of F(-) sorption. For equilibrium F(-) concentrations more than 1 mmol dm(-3), lower calcination temperatures favored the co-precipitation of F(-) with Mg(OH)(2), probably leading to the formation of Mg(OH)(2-x)F(x), and the achievement of larger sorption density. This is the first paper which describes the relationship between the solid base characteristics obtained by CO(2)-TPD for MgO with different calcination temperatures as a function of the reactivity of F(-) sorption in the aqueous phase. Copyright © 2011 Elsevier B.V. All rights reserved.

  2. Polyaniline (PANI) modified bentonite by plasma technique for U(VI) removal from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xinghao [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China); Intelligent Manufacturing Technology Research Institute, Hefei University of Technology, Hefei 230088 (China); Cheng, Cheng [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Xiao, Chengjian, E-mail: xiaocj@caep.cn [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China); Shao, Dadong, E-mail: shaodadong@126.com [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Xu, Zimu, E-mail: xzm@mail.ustc.edu.cn [Intelligent Manufacturing Technology Research Institute, Hefei University of Technology, Hefei 230088 (China); Wang, Jiaquan; Hu, Shuheng [Intelligent Manufacturing Technology Research Institute, Hefei University of Technology, Hefei 230088 (China); Li, Xiaolong; Wang, Weijuan [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China)

    2017-07-31

    Highlights: • PANI/bentonie can be synthesized by simple plasma technique. • PANI/bentonie has an excellent adsorption capacity for trace uranium in solution. • U(VI) adsorption on PANI/bentonite is a spontaneous and endothermic process. - Abstract: Polyaniline (PANI) modified bentonite (PANI/bentonie) was synthesized by plasma induced polymerization of aniline on bentonite surface, and applied to uptake of uranium(VI) ions from aqueous solution. The as-synthesized PANI/bentonie was characterized by scanning electron microscopy (SEM), powder X-ray diffraction (XRD), thermal gravimetric analysis (TGA), and X-ray photoelectron spectroscopy (XPS). Batch adsorption technique was utilized to investigate the adsorption of U(VI) on bentonite and PANI/bentonite. The adsorption of U(VI) (10 mg/L) on PANI/bentonite surface is fairly depend on solution pH, ionic strength, and temperature in solution. The modified PANI on PANI/bentonite surface significantly enhances its adsorption capability for U(VI). The presence of humic acid (HA) can sound enhance U(VI) adsorption on PANI/bentonite at pH < 6.5 because of the strong complexation, and inhibits U(VI) adsorption at pH > 6.5. According to the thermodynamic parameters, the adsorption of U(VI) on PANI/bentonite surface is a spontaneous and endothermic process. The results highlight the application of PANI/bentonite composites as candidate material for the uptake of trace U(VI) from aqueous solution.

  3. Uranium(VI adsorption on surfactant modified heulandite/clinoptilolite rich tuff

    Directory of Open Access Journals (Sweden)

    SRDJAN MATIJASEVIC

    2006-12-01

    Full Text Available The adsorption of uranium(VI on heulandite/clinoptilolite rich zeolitic tuff modified with diferent amounts (2, 5 and 10 meq/100 g of hexadecyltrimethyl ammonium (HDTMA ion was investigated. The organozeolites were prepared by ion exchange of inorganic cations at the zeolite surface with HDTMA ions, and the three prepared samples were denoted as OA-2, OA-5 and OA-10. The maximal amount of HDTMAin the organozeolite OA-10 (10 meq/100 g was equal to the external cation exchange capacity of the starting material. The results showed that uranium( VI adsorption on unmodified zeolitic tuff was low (0.34 mg uranium(VI/g adsorbent, while for the organozeolites, the adsorption increased with increasing amount of HDTMA at the zeolitic surface. The highest adsorption indexes were achieved for the organozeolite OA-10, in which all the surface inorganic cations had been replaced with HDTMA. An investigation of the adsorption of uranium(VI ions onto organozeolite OA-10 at different pH values (3, 6 and 8 showed that the adsorption index increased with increasing amount of adsorbent in the suspension. Since uranium(VI speciation is highly dependent on pH, from the adsorption isotherms, it can be seen that uranium(VI adsorption on organozeolite OA-10 at pH 6 and 8 is well described by a Langmuir type of isotherm, while at pH 3, it corresponds to a Type III isotherm.

  4. Quantification of Cation Sorption to Engineered Barrier Materials Under Extreme Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Powell, Brian [Clemson Univ., SC (United States); Schlautman, Mark [Clemson Univ., SC (United States); Rao, Linfeng [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Nitsche, Heino [Univ. of California, Berkeley, CA (United States); Gregorich, Kenneth [Univ. of California, Berkeley, CA (United States)

    2016-02-02

    The objective of this research is to examine mechanisms and thermodynamics of actinide sorption to engineered barrier materials (iron (oxyhydr)oxides and bentonite clay) for nuclear waste repositories under high temperature and high ionic strength conditions using a suite of macroscopic and microscopic techniques which will be coupled with interfacial reaction models. Gaining a mechanistic understanding of interfacial processes governing the sorption/sequestration of actinides at mineral-water interfaces is fundamental for the accurate prediction of actinide behavior in waste repositories. Although macroscale sorption data and various spectroscopic techniques have provided valuable information regarding speciation of actinides at solid-water interfaces, significant knowledge gaps still exist with respect to sorption mechanisms and the ability to quantify sorption, particularly at high temperatures and ionic strengths. This objective is addressed through three major tasks: (1) influence of oxidation state on actinide sorption to iron oxides and clay minerals at elevated temperatures and ionic strengths; (2) calorimetric titrations of actinide-mineral suspensions; (3) evaluation of bentonite performance under repository conditions. The results of the work will include a qualitative conceptual model and a quantitative thermodynamic speciation model describing actinide partitioning to minerals and sediments, which is based upon a mechanistic understanding of specific sorption processes as determined from both micro-scale and macroscale experimental techniques. The speciation model will be a thermodynamic aqueous and surface complexation model of actinide interactions with mineral surfaces that is self-consistent with macroscopic batch sorption data, calorimetric and potentiometric titrations, X-ray absorption Spectroscopy (XAS, mainly Extended X-ray Absorption Fine Structure (EXAFS)), and electron microscopy analyses. The novelty of the proposed work lies largely in

  5. Visible light Cr(VI) reduction and organic chemical oxidation by TiO2 photocatalysis.

    Science.gov (United States)

    Sun, Bo; Reddy, Ettireddy P; Smirniotis, Panagiotis G

    2005-08-15

    Here we report the simultaneous Cr(VI) reduction and 4-chlorophenol (4-CP) oxidation in water under visible light (wavelength > 400 nm) using commercial Degussa P25 TiO2. This remarkable observation was attributed to a synergistic effect among TiO2, Cr(VI), and 4-CP. It is well known that TiO2 alone cannot remove either 4-CP or Cr(VI) efficiently under visible light. Moreover, the interaction between Cr(VI) and 4-CP is minimal if not negligible. However, we found that the combination of TiO2, Cr(VI), and 4-CP together can enable efficient Cr(VI) reduction and 4-CP oxidation under visible light. The specific roles of the three ingredients in the synergistic system were studied parametrically. It was found that optimal concentrations of Cr(VI) and TiO2 exist for the Cr(VI) reduction and 4-CP oxidation. Cr(VI) was compared experimentally with other metals such as Cu(ll), Fe(lll), Mn(IV), Ce(IV), and V(V). Among all these metal ions, only Cr(VI) promotes the photocatalytic oxidation of 4-CP. The amount of 4-CP removed was directly related to the initial concentration of Cr(VI). The system was also tested with four other chemicals (aniline, salicylic acid, formic acid, and diethyl phosphoramidate). We found that the same phenomenon occurred for organics containing acid and/or phenolic groups. Cr(VI) was reduced at the same time as the organic chemicals being oxidized during photoreaction under visible light. The synergistic effect was also found with pure anatase TiO2 and rutile TiO2. This study demonstrates a possible economical way for environmental cleanup under visible light.

  6. Sorption interactions of heavy metals with biochar in soil remediation studies

    Science.gov (United States)

    Fristak, Vladimir; Friesl-Hanl, Wolfgang; Wawra, Anna; Soja, Gerhard

    2015-04-01

    study of sorption mechanisms showed differences in the sorption of the targeted heavy metals in relation to the contribution of ion-exchange and precipitation processes. We confirmed the effectivity of physico-chemical artificial aging on sorption capacity of biochar in terms of changes in surface structure. Based on these results, the application potential of biochar as sorption material for stabilizing heavy metals in soils is discussed.

  7. Sorption kinetics of heavy oil into porous carbons.

    Science.gov (United States)

    Nishi, Yoko; Iwashita, Norio; Sawada, Yoshihiro; Inagaki, Michio

    2002-12-01

    Sorption kinetics of heavy oil into porous carbons was evaluated by a concept of liquid sorption coefficient obtained from the weight increase of heavy oil with sorption time, which was measured by a wicking test. Exfoliated graphite, carbonized fir fibers and carbon fiber felts were used as porous materials. It was found that the liquid sorption coefficient of fibrous carbons was twice larger than that of exfoliated graphite. Such a difference in the liquid sorption coefficient between the exfoliated graphite and two fibrous carbons was caused by a difference in effective sorption porosity and tortuosity between them. For the exfoliated graphite and carbonized fir fibers, the liquid sorption coefficient and the effective sorption porosity were strongly dependent on their density. The maximum values of both liquid sorption coefficient and effective sorption porosity of the exfoliated graphite were shown at the bulk density around 16 kg/m3. The liquid sorption coefficient of the carbonized fir fibers increased with increasing the density in the range from 6 to 30 kg/m3. When the carbonized fir fibers were densified above 30 kg/m3, the sorption rate was saturated. On the other hand, the sorption kinetics into the carbon fiber felt was almost independent of the bulk density, because the density of the carbon fiber felt is not effective for the pore structure. The effect of bulk density on the sorption kinetics could be supported from an analysis of pore structure of the porous carbons with different densities, which was measured by mercury porosimeter.

  8. Sorption Speciation of Lanthanides/Actinides on Minerals by TRLFS, EXAFS and DFT Studies: A Review

    Directory of Open Access Journals (Sweden)

    Xiaoli Tan

    2010-11-01

    Full Text Available Lanthanides/actinides sorption speciation on minerals and oxides by means of time resolved laser fluorescence spectroscopy (TRLFS, extended X-ray absorption fine structure spectroscopy (EXAFS and density functional theory (DFT is reviewed in the field of nuclear disposal safety research. The theoretical aspects of the methods are concisely presented. Examples of recent research results of lanthanide/actinide speciation and local atomic structures using TRLFS, EXAFS and DFT are discussed. The interaction of lanthanides/actinides with oxides and minerals as well as their uptake are also of common interest in radionuclide chemistry. Especially the sorption and inclusion of radionuclides into several minerals lead to an improvement in knowledge of minor components in solids. In the solid-liquid interface, the speciation and local atomic structures of Eu(III, Cm(III, U(VI, and Np(IV/VI in several natural and synthetic minerals and oxides are also reviewed and discussed. The review is important to understand the physicochemical behavior of lanthanides/actinides at a molecular level in the natural environment.

  9. A simple Cr(VI)–S(IV)–O{sub 2} system for rapid and simultaneous reduction of Cr(VI) and oxidative degradation of organic pollutants

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Yanan; Yang, Shaojie [Department of Environmental Science, Hubei Key Lab of Biomass Resource Chemistry and Environmental Biotechnology, School of Resources and Environmental Science, Wuhan University, 430079 (China); Zhou, Danna, E-mail: zdncug@163.com [Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Wu, Feng [Department of Environmental Science, Hubei Key Lab of Biomass Resource Chemistry and Environmental Biotechnology, School of Resources and Environmental Science, Wuhan University, 430079 (China)

    2016-04-15

    Highlights: • Rapid and simultaneous reduction of Cr(VI) and degradation of organic pollutants occur. • Oxysulfur radicals generated in Cr(VI)–S(IV)–O{sub 2} system oxidize the organic pollutants. • Acidic pH facilitates the reactions from both directions of reduction and oxidation. • Degradation potential of aromatic amines depends on the substituted groups. • Cr(VI)–S(IV)–O{sub 2} system is promising for “waste control by waste”. - Abstract: Hexavalent chromium (Cr(VI)), a heavy-metal contaminant, can be easily reduced to less toxic trivalent chromium (Cr(III)) by sulfite ions (S(IV)). However, S(IV) has not drawn as much attention as the ferrous ion has. We report herein a novel Cr(VI)–S(IV)–O{sub 2} system containing sulfite ions that rapidly and simultaneously reduces Cr(VI) and oxidize organic pollutants in the presence of oxygen in aqueous solutions. This Cr(VI)–S(IV)-O{sub 2} system contains the initiator Cr(VI), the reductant S(IV), and the oxidant O{sub 2}, which produce oxysulfur radicals (mainly SO{sub 4}·{sup −} and SO{sub 5}·{sup −}) and hydroxyl radicals (OH·). The Cr(VI)/S(IV) molar ratio, pH, and oxygen content play important roles in the entire reaction system. Acidic conditions (pH 3.0) facilitated degradation of organic compounds and reduction of Cr(VI) as well. In addition, experiments of rapid degradation of several kinds of organic pollutants such as azo dye (acid orange 7, AO7), aniline, phenol, bisphenol A etc were also conducted. Preliminary results show that the removal rates of the analogs of phenols or aromatic amines in this Cr(VI)–S(IV)–O{sub 2} system have a relationship with the electronic parameters (Hammett constant, σ) of the substituted groups. Thus, the Cr(VI)–S(IV)–O{sub 2} system, provides an excellent strategy of “waste control by waste” for removing multiple industrial contaminants.

  10. Biosorption of Cr(VI from Aqueous Solutions Using Trametes Versicolor Polyporus Fungi

    Directory of Open Access Journals (Sweden)

    M. Venkata Subbaiah

    2008-01-01

    Full Text Available Removal of chromium(VI from aqueous solution was studied using abundantly available trametes versicolor polyporus fungi as biosorbing medium under equilibrium and column flow conditions. Various sorption parameters such as contact time, effect of pH, concentration of Cr(VI and amount of biomass on the adsorption capacity of the biosorbent were studied. The equilibrium adsorption data were fitted to Freundlich and Langmuir adsorption isotherm models and the model parameters are evaluated. In addition, the data were used to predict the kinetics of adsorption. The results indicated that the adsorption of Cr(VI on fungi followed second order kinetics. The column flow adsorption data were used to predict break through curves. The fungi loaded with Cr(VI was regenerated with 0.1 M NaOH solution and the regenerated biomass was used in the subsequent adsorptiondesorption cycles. The experimental results demonstrated that the trametes versicolor polyporus fungi could be used as sorbent for immobilizing Cr(VI.

  11. Cr(VI) Adsorption to Magnetic Iron Oxide Nanoparticle-Multi-Walled Carbon Nanotube Adsorbents.

    Science.gov (United States)

    Lee, Chang-Gu; Kim, Song-Bae

    2016-11-01

      The aim of this study was to investigate the Cr(VI) adsorption to magnetic iron oxide(MIO) nanoparticle- multi-walled carbon nanotubes (MWCNTs) in aqueous solutions using batch experiments. Results show that the maximum adsorption capacity of Cr(VI) to MIO-MWCNTs was 11.256 mg/g. Kinetic model analysis demonstrates that the pseudo-second-order model and Elovich model are suitable for describing the kinetic data. Thermodynamic analysis indicates that Cr(VI) adsorption to MIO-MWCNTs decreased with increasing temperature from 5-60 °C, indicating the spontaneous and exothermic nature of the sorption process. Equilibrium isotherm analysis demonstrates that the Redlich-Peterson model suitably describes the equilibrium data. In the pH experiments, Cr(VI) adsorption to MIO-MWCNTs decreased gradually from 5.70-2.13 mg/g with increasing pH from 3.0-7.3. Sequential extraction indicates that, among the five binding forms of Cr(VI) associated with MIO-MWCNTs, the predominant contributions are the fraction bound to Fe-Mn oxides (57.82%) and the residual (23.38%).

  12. Isotope fractionation and spectroscopic analysis as an evidence of Cr(VI) reduction during biosorption.

    Science.gov (United States)

    Šillerová, Hana; Chrastný, Vladislav; Čadková, Eva; Komárek, Michael

    2014-01-01

    This work investigates the mechanisms behind Cr(VI) biosorption/reduction on three biomaterials (brewers draff, grape waste and synthetic humic acid). Coupled Cr isotope analysis with ICP-OES, XPS and SEM was tested as a novel approach to study the reduction of Cr(VI) by the biomaterials. The Cr(VI) biosorption process was accompanied with heavier Cr isotopes enrichment in the remaining Cr(VI) fraction. A significant fractionation of Cr stable isotopes was observed with no significant pH effect; δ(53)Cr of the remaining fraction ranged from 0.2‰ to 1.9‰ while δ(53)Cr of the product (sorbed Cr) ranged from -1.2‰ to -2.8‰. The Rayleigh fractionation model fitted well the measured data and Cr isotope analysis provides thus an efficient tool to quantify Cr(VI) reduction by different biomaterials. In general, the sorption/reduction potential of the three studied biomaterials decreased in the following order: grape waste>humic acids>brewers draff. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Synthesis of Graphene Oxide by Oxidation of Graphite with Ferrate(VI) Compounds: Myth or Reality?

    Science.gov (United States)

    Sofer, Zdeněk; Luxa, Jan; Jankovský, Ondřej; Sedmidubský, David; Bystroň, Tomáš; Pumera, Martin

    2016-09-19

    It is well established that graphene oxide can be prepared by the oxidation of graphite using permanganate or chlorate in an acidic environment. Recently, however, the synthesis of graphene oxide using potassium ferrate(VI) ions has been reported. Herein, we critically replicate and evaluate this new ferrate(VI) oxidation method. In addition, we test the use of potassium ferrate(VI) for the synthesis of graphene oxide under various experimental routes. The synthesized materials are analyzed by a number of analytical methods in order to confirm or disprove the possibility of synthesizing graphene oxide by the ferrate(VI) oxidation route. Our results confirm the unsuitability of using ferrate(VI) for the oxidation of graphite on graphene oxide because of its high instability in an acidic environment and low oxidation power in neutral and alkaline environments. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Reduction of trace quantities of chromium(VI by strong acids

    Directory of Open Access Journals (Sweden)

    Pezzin Sérgio H

    2004-01-01

    Full Text Available The chemical behavior of Cr(VI at low concentrations (10-4 to 10-7 mol L-1 in several strong acids was studied using high specific activity 51Cr(VI as a tracer. The speciation of the products from these systems was carried out by ion exchange chromatography with stepwise elution. The results show that trace quantities of Cr(VI, monitored by means of radiochromium (51Cr, are reduced in the presence of mineral acids such as perchloric, hydrochloric, hydrofluoric, sulfuric, nitric and trifluoromethanesulfonic acids, even in the absence of conventional reducing agents, producing different measureable Cr(III species, depending on the acid anion. Detailed studies of the reduction of low concentrations of Cr(VI with nitric acid have shown that the relative rate of reduction increases as the concentration of the acid increases or as the concentration of the Cr(VI decreases.

  15. ION-EXCHANGE PROPERTIES OF IONITES WITH VARIOUS FUNCTIONAL GROUPS

    Directory of Open Access Journals (Sweden)

    Manhur Jafarli

    2016-12-01

    Full Text Available Sorption regularities of Zn2+ and Pb2+ ions from water solutions by ion exchangers of Diaion CR 11, Amberlite IRC 748 with iminodiacetic acid functional group and Dowex M 4195 with bis-picolilamine functional group are investigated, sorption isotherms are plotted, isotherms are analyzed on the basis of known models, thermodynamic parameters are calculated on the basis of kinetic data, thermodynamic factor controlling processes is determined.

  16. Sequential injection analysis as a tool for on-line monitoring the sorption of fulvic acid onto modified vermiculite

    Directory of Open Access Journals (Sweden)

    Abate Gilberto

    2006-01-01

    Full Text Available This paper presents a sequential injection system associated with a tangential filtration unit and an ultraviolet detector for on-line monitoring of fulvic acid sorption onto two modified vermiculites. With the proposed approach it was possible to improve the temporal resolution in the investigation of the equilibrium time needed for the system sorbent-sorbate to reach the chemical equilibrium. Sorption onto a 10 g L-1 suspension of vermiculite material modified by intercalation of polyhydroxycations of Fe(III was fast, reaching the equilibrium after 4 min of contact time, and resulting in sorption of 97.9 % of the initial 10 mg L-1 fulvic acid concentration. Sorption onto a 10 g L-1 suspension of an organic vermiculite which was modified by ion exchange with hexadecyltrimethylammonium bromide exhibited a fast initial rate of sorption, followed by desorption and re-adsorption processes, reaching the equilibrium after 30 min of contact time, with sorption of 98% of the initial 10 mg L-1 fulvic acid concentration.

  17. Investigation of uranium (VI) adsorption by polypyrrole

    Energy Technology Data Exchange (ETDEWEB)

    Abdi, S. [Faculty of Chemical, Petroleum and Gas Engineering, Semnan University, Semnan 35195-363 (Iran, Islamic Republic of); Nasiri, M., E-mail: mnasiri@semnan.ac.ir [Faculty of Chemical, Petroleum and Gas Engineering, Semnan University, Semnan 35195-363 (Iran, Islamic Republic of); Mesbahi, A. [Faculty of Chemical, Petroleum and Gas Engineering, Semnan University, Semnan 35195-363 (Iran, Islamic Republic of); Khani, M.H. [Nuclear Fuel Cycle Research School, Nuclear Science and Technology Research Institute, Tehran, 14395-836 (Iran, Islamic Republic of)

    2017-06-15

    Highlights: • The adsorbent (polypyrrole) was synthesized by a chemical method using PEG, DBSNa and CTAB as the surfactant. • The solution pH was one of the most important parameters affecting the adsorption of uranium. • The CTAB provided higher removal percentage compared with the other surfactants. • The maximum adsorption capacity obtained from Langmuir isotherm was 87.72 mg/g. • The pseudo second-order model fitted well with the adsorption kinetic of polypyrrole to uranium. - Abstract: The purpose of this study was to investigate the adsorption of uranium (VI) ions on the polypyrrole adsorbent. Polypyrrole was synthesized by a chemical method using polyethylene glycol, sodium dodecylbenzenesulfonate, and cetyltrimethylammonium bromide as the surfactant and iron (III) chloride as an oxidant in the aqueous solution. The effect of various surfactants on the synthesized polymers and their performance as the uranium adsorbent were investigated. Adsorbent properties were characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) techniques. The effect of different parameters such as pH, contact time, initial metal ion concentrations, adsorbent dose, and the temperature was investigated in the batch system for uranium adsorption process. It has been illustrated that the adsorption equilibrium time is 7 min. The results showed that the Freundlich model had the best agreement and the maximum adsorption capacity of polypyrrole for uranium (VI) was determined 87.72 mg/g from Langmuir isotherm. In addition, the mentioned adsorption process was fast and the kinetic data were fitted to the Pseudo first and second order models. The adsorption kinetic data followed the pseudo-second-order kinetic model. Moreover, the thermodynamic parameters ΔG{sup 0}, ΔH{sup 0} and ΔS{sup 0} showed that the uranium adsorption process by polypyrrole was endothermic and spontaneous.

  18. Studies on sorption properties of zeolite derived from Indian fly ash.

    Science.gov (United States)

    Mishra, T; Tiwari, S K

    2006-09-01

    Indian fly ash has been completely converted to crystalline porous 13X zeolite by NaOH fusion at 600 degrees C followed by hydrothermal treatment at 105 degrees C for 20 h. Obtained materials were characterized by XRD, SEM and surface area measurement. Prepared material was used for the sorption study of different metal ions (Cu(2+), Co(2+) and Ni(2+)) at different pH, temperature. Thermodynamic data (DeltaS, DeltaH and DeltaG) corresponding to different metal ion uptake were evaluated from Langmuir equation. In all the experiment sorption capacity of prepared zeolite was found to be quite high than that of fly ash at acidic pH. However, the uptake selectivity order for both the materials is Cu(2+)>Co(2+)>Ni(2+).

  19. Development of a Composite Non-Electrostatic Surface Complexation Model Describing Plutonium Sorption to Aluminosilicates

    Energy Technology Data Exchange (ETDEWEB)

    Powell, B A; Kersting, A; Zavarin, M; Zhao, P

    2008-10-28

    Due to their ubiquity in nature and chemical reactivity, aluminosilicate minerals play an important role in retarding actinide subsurface migration. However, very few studies have examined Pu interaction with clay minerals in sufficient detail to produce a credible mechanistic model of its behavior. In this work, Pu(IV) and Pu(V) interactions with silica, gibbsite (Aloxide), and Na-montmorillonite (smectite clay) were examined as a function of time and pH. Sorption of Pu(IV) and Pu(V) to gibbsite and silica increased with pH (4 to 10). The Pu(V) sorption edge shifted to lower pH values over time and approached that of Pu(IV). This behavior is apparently due to surface mediated reduction of Pu(V) to Pu(IV). Surface complexation constants describing Pu(IV)/Pu(V) sorption to aluminol and silanol groups were developed from the silica and gibbsite sorption experiments and applied to the montmorillonite dataset. The model provided an acceptable fit to the montmorillonite sorption data for Pu(V). In order to accurately predict Pu(IV) sorption to montmorillonite, the model required inclusion of ion exchange. The objective of this work is to measure the sorption of Pu(IV) and Pu(V) to silica, gibbsite, and smectite (montmorillonite). Aluminosilicate minerals are ubiquitous at the Nevada National Security Site and improving our understanding of Pu sorption to aluminosilicates (smectite clays in particular) is essential to the accurate prediction of Pu transport rates. These data will improve the mechanistic approach for modeling the hydrologic source term (HST) and provide sorption Kd parameters for use in CAU models. In both alluvium and tuff, aluminosilicates have been found to play a dominant role in the radionuclide retardation because their abundance is typically more than an order of magnitude greater than other potential sorbing minerals such as iron and manganese oxides (e.g. Vaniman et al., 1996). The sorption database used in recent HST models (Carle et al., 2006

  20. Sorption kinetics of Cs and Sr in sediments of a Savannah River Site reservoir

    Energy Technology Data Exchange (ETDEWEB)

    Stephens, J.A.

    1997-07-01

    Laboratory measurements of the sorption and desorption of {sup 134}Cs and {sup 85}Sr to sediments were conducted. These sediments were sampled from the profundal zone of Par Pond at the Savannah River Site, Aiken, South Carolina. The isotopes {sup 134}Cs and {sup 85}Sr were used to trace the sorption properties of the main contaminants found in the reservoir which are {sup 137}Cs and {sup 90}Sr respectively. The sorption behavior of these two elements was studied using spiked sediment/water slurries of a known mass to volume ratio. The results reveal that Sr undergoes significant reversible sorption while a fraction of Cs irreversibly sorbs to the sediment. The calculated distribution coefficient Kd at equilibrium was (3 {+-} 0.6) x 10{sup 3} for {sup 134}Cs after 60 d and (1 {+-} 0.2) x 10{sup 3} for {sup 85}Sr after 7 d at pH {approx} 6 and slurry ratio of 1:1000 g/ml. The K{sub d} for {sup 134}Cs ranged from 2 x 10{sup 2} to 3 x 10{sup 4} depending on pH and conductivity. The {sup 85}Sr reached equilibrium in a few days, while {sup 134}Cs reached an apparent equilibrium in 1--2 months. The K{sub d} for {sup 134}Cs was a function of the slurry ratio, pH, conductivity, and contact time. These factors were interrelated since the sediments released ions to the slurry mixture which decreased the pH and increased the conductivity. A sorption isotherm measured for {sup 134}Cs was linear at water concentrations from 60 mBq/ml to 20 Bq/ml. A kinetic model was proposed to describe the basic sorption of {sup 134}Cs to Par Pond sediments under homogeneous laboratory conditions.

  1. Prediction of metal sorption in soils

    Energy Technology Data Exchange (ETDEWEB)

    WESTRICH,HENRY R.; ANDERSON JR.,HAROLD L.; ARTHUR,SARA E.; BRADY,PATRICK V.; CYGAN,RANDALL T.; LIANG,JIANJIE; ZHANG,PENGCHU; YEE,N.

    2000-03-02

    Radionuclide transport in soils and groundwaters is routinely calculated in performance assessment (PA) codes using simplified conceptual models for radionuclide sorption, such as the K{sub D} approach for linear and reversible sorption. Model inaccuracies are typically addressed by adding layers of conservativeness (e.g., very low K{sub D}'s), and often result in failed transport predictions or substantial increases in site cleanup costs. Realistic assessments of radionuclide transport over a wide range of environmental conditions can proceed only from accurate, mechanistic models of the sorption process. They have focused on the sorption mechanisms and partition coefficients for Cs{sup +}, Sr{sup 2+} and Ba{sup 2+} (analogue for Ra{sup 2+}) onto iron oxides and clay minerals using an integrated approach that includes computer simulations, sorption/desorption measurements, and synchrotron analyses of metal sorbed substrates under geochemically realistic conditions. Sorption of Ba{sup 2+} and Sr{sup 2+} onto smectite is strong, pH-independent, and fully reversible, suggesting that cation exchange at the interlayer basal sites controls the sorption process. Sr{sup 2+} sorbs weakly onto geothite and quartz, and is pH-dependent. Sr{sup 2+} sorption onto a mixture of smectite and goethite, however, is pH- and concentration dependent. The adsorption capacity of montmorillonite is higher than that of goethite, which may be attributed to the high specific surface area and reaction site density of clays. The presence of goethite also appears to control the extent of metal desorption. In-situ, extended X-ray absorption fine structure (EXAFS) spectroscopic measurements for montmorillonite and goethite show that the first shell of adsorbed Ba{sup 2+} is coordinated by 6 oxygens. The second adsorption shell, however, varies with the mineral surface coverage of adsorbed Ba{sup 2+} and the mineral substrate. This suggests that Ba{sup 2+} adsorption on mineral surfaces

  2. The impact of solution chemistry of electrolyte on the sorption of pentachlorophenol and phenanthrene by natural hematite nanoparticles.

    Science.gov (United States)

    Zeng, Fanfeng; He, Yan; Lian, Zhenghua; Xu, Jianming

    2014-01-01

    Hematite nanoparticles (NPs) were studied as a sorbent for hydrophobic organic contaminants (OCs) under natural ambient conditions through specially designed contrasting solution chemistry of electrolyte. Ionizable pentachlorophenol (PCP) and non-ionizable phenanthrene (PHE) were selected as representative OCs. The sorption capacities of PCP and PHE were pH-dependent, and a larger amount of PCP was sorbed at pH values below its pKa (4.75). However, the PHE sorption capacity was higher at relatively high or low pHs (e.g. below 4.0 and above 10.0), possibly due to the larger available surface area of the hematite NPs, caused by the higher values of net charges and charge density. Changes in pH might thus affect the sorption of OCs by hematite NPs, through modification of the surface characteristics of the sorbent and the electronic properties of the sorbate molecules. The influence of different ionic strengths indicated that the amounts of PCP and PHE sorbed by hematite NPs decreased as a concentration function of different types of ions (e.g. Na(+), K(+), Mg(2+) and Ca(2+)), with the underlying mechanism possibly being due to four interactions i.e. hydrogen-bonding, competitive sorption by ions in the ambient solution, screening effects and aggregation effects. The results confirmed that the surface chemistry of hematite NPs, the chemical properties of PCP and PHE, and solution chemistry (e.g. pH and ionic strength) of the electrolyte all played an important role in PCP and PHE sorption by hematite NPs. By comparison of both sorption capacity and ecologic advantages, our results suggested that natural hematite NPs would be more competitive and efficient for PCP and PHE sorption than engineered NPs. This finding increases our knowledge regarding the environmental function of natural NPs (such as hematite NPs) for OC remediation through manipulating their interfacial behavior. © 2013.

  3. Sorption of small molecules in polymeric media

    Science.gov (United States)

    Camboni, Federico; Sokolov, Igor M.

    2016-12-01

    We discuss the sorption of penetrant molecules from the gas phase by a polymeric medium within a model which is very close in spirit to the dual sorption mode model: the penetrant molecules are partly dissolved within the polymeric matrix, partly fill the preexisting voids. The only difference with the initial dual sorption mode situation is the assumption that the two populations of molecules are in equilibrium with each other. Applying basic thermodynamics principles we obtain the dependence of the penetrant concentration on the pressure in the gas phase and find that this is expressed via the Lambert W-function, a different functional form than the one proposed by dual sorption mode model. The Lambert-like isotherms appear universally at low and moderate pressures and originate from the assumption that the internal energy in a polymer-penetrant-void ternary mixture is (in the lowest order) a bilinear form in the concentrations of the three components. Fitting the existing data shows that in the domain of parameters where the dual sorption mode model is typically applied, the Lambert function, which describes the same behavior as the one proposed by the gas-polymer matrix model, fits the data equally well.

  4. Moisture sorption of Thai red curry powder

    Directory of Open Access Journals (Sweden)

    Sudathip Inchuen

    2009-12-01

    Full Text Available Moisture sorption study was conducted on Thai red curry powder prepared by two different drying methods, viz. microwave and hot-air drying. Moisture sorption isotherms of the red curry powder at 30 C and water activity in the range of 0.113-0.970 were determined by a static gravimetric method. The isotherms exhibited Type III behaviour. The moisture sorption data were fitted to several sorption models and a non-linear regression analysis method was used to evaluate the constants of the sorption equations. The fit was evaluated using the coefficient of determination (R2, the reduced chi-square (2 and the root mean square error (RMSE. The GAB model followed by the Lewiski-3 model gave the best fit to the experimental data. The monolayer moisture content, taken as the safe minimum moisture level in the red curry powder, was determined using the BET equation and was found to range between 0.080 - 0.085 gram water per gram dry matter.

  5. Experimental and modeling studies on sorption and diffusion of radium in bentonite.

    Science.gov (United States)

    Tachi, Y; Shibutani, T; Sato, H; Yui, M

    2001-02-01

    The sorption and desorption behavior of radium on bentonite and purified smectite was investigated as a function of pH, ionic strength and liquid to solid ratio by batch experiments. The distribution coefficients (Kd) were in the range of 10(2) to > 10(4) ml g-1 and depended on ionic strength and pH. Most of sorbed Ra was desorbed by 1 M KCl. The results for purified smectite indicated that Ra sorption is dominated by ion exchange at layer sites of smectite, and surface complexation at edge sites may increase Ra sorption at higher pH region. Reaction parameters between Ra and smectite were determined based on an interaction model between smectite and groundwater. The reaction parameters were then used to explain the results of bentonite by considering dissolution and precipitation of minerals and soluble impurities. The dependencies of experimental Kd values on pH, ionic strength and liquid to solid ratio were qualitatively explained by the model. The modeling result for bentonite indicated that sorption of Ra on bentonite is dominated by ion exchange with smectite. The observed pH dependency was caused by changes of Ca concentration arising from dissolution and precipitation of calcite. Diffusion behavior of Ra in bentonite was also investigated as a function of dry density and ionic strength. The apparent diffusion coefficients (Da) obtained in compacted bentonite were in the range of 1.1 x 10(-11) to 2.2 x 10(-12) m2 s-1 and decreased with increasing in dry density and ionic strength. The Kd values obtained by measured effective diffusion coefficient (De) and modeled De were consistent with those by the sorption model in a deviation within one order of magnitude.

  6. Sorption of Pb2+ from Aqueous Solution unto Modified Rice Husk: Isotherms Studies

    Directory of Open Access Journals (Sweden)

    A. O. Dada

    2013-01-01

    Full Text Available Investigation of the sorption potential of rice husk, an agricultural waste, as an adsorbent was carried out. The rice husk was modified with orthophosphoric acid and was used for adsorption of lead (II ions (Pb2+ from aqueous solution. Physicochemical properties of the modified rice husk were determined. Equilibrium sorption data were confirmed with Langmuir, Freundlich and Temkin adsorption isotherms. On the basis of adsorption isotherm graphs, R2 values were determined to be 0.995, 0.916, and 0.797 for Langmuir, Temkin, and Freundlich isotherms, respectively, indicating that the data fitted well into the adsorption isotherms, but Langmuir isotherm is a better model. The maximum monolayer coverage from Langmuir studies, Qmax=138.89 mg/g, Langmuir isotherm constant, KL=0.699 L/mg, and the separation factor, RL=1.41×10−2 at 100 mg/L of lead(II ions indicating that the sorption process, was favourable. The suitability of modified rice husk as an adsorbent for the removal of lead ions from aqueous solution and its potential for pollution control is established.

  7. Competitive Adsorption of Cd(II), Cr(VI), and Pb(II) onto Nanomaghemite: A Spectroscopic and Modeling Approach.

    Science.gov (United States)

    Komárek, Michael; Koretsky, Carla M; Stephen, Krishna J; Alessi, Daniel S; Chrastný, Vladislav

    2015-11-03

    A combined modeling and spectroscopic approach is used to describe Cd(II), Cr(VI), and Pb(II) adsorption onto nanomaghemite and nanomaghemite coated quartz. A pseudo-second order kinetic model fitted the adsorption data well. The sorption capacity of nanomaghemite was evaluated using a Langmuir isotherm model, and a diffuse double layer surface complexation model (DLM) was developed to describe metal adsorption. Adsorption mechanisms were assessed using X-ray photoelectron spectroscopy and X-ray absorption spectroscopy. Pb(II) adsorption occurs mainly via formation of inner-sphere complexes, whereas Cr(VI) likely adsorbs mainly as outer-sphere complexes and Cd(II) as a mixture of inner- and outer-sphere complexes. The simple DLM describes well the pH-dependence of single adsorption edges. However, it fails to adequately capture metal adsorption behavior over broad ranges of ionic strength or metal-loading on the sorbents. For systems with equimolar concentrations of Pb(II), Cd(II), and Cr(VI). Pb(II) adsorption was reasonably well predicted by the DLM, but predictions were poorer for Cr(VI) and Cd(II). This study demonstrates that a simple DLM can describe well the adsorption of the studied metals in mixed sorbate-sorbent systems, but only under narrow ranges of ionic strength or metal loading. The results also highlight the sorption potential of nanomaghemite for metals in complex systems.

  8. Removal of chromium (VI) from water by micro-alloyed aluminium ...

    African Journals Online (AJOL)

    This paper deals with Cr(VI) ion removal from water, by micro-alloyed aluminium composite (MAlC), under flow conditions. In a water environment the MAlC acts as a strong reducing agent. Dissolving it in water is accompanied by the generation of Al(III) ions and reduction of water to H2, with OH- ions. The final product is ...

  9. Sorption kinetics of cesium on natural mordenite

    Energy Technology Data Exchange (ETDEWEB)

    Tienjui Liang; Yuecheung Tsai Joseph [Taiwan Power Co., Taipei, Taiwan (China). Radiation Lab.

    1995-01-01

    The characteristics of sorption kinetics of cesium on natural mordenite, including apparent rate constant, intraparticle diffusion coefficient and reaction mechanisms, were investigated in this study. The apparent rate constant of sorption, as derived from the semi-empirical Elovich equation, was indicated from the experimental results to be about 56.9 {mu}equiv {center_dot} g{sup -1}{center_dot} s{sup -1}. The rate-determining step of sorption reaction was identified as the intraparticle diffusion of cesium cation from the main channel to site B, which is located in the side void, through the side channel system of mordenite. The linear and nonlinear intraparticle diffusion coefficients of Cs{sup +} were observed via calculation by the spherical diffusion model as being 4.7 x 10{sup 18} and 3.5 x 10{sup 18} m{sup 2}{center_dot} s{sup -1}, respectively. (author).

  10. Simulations of hydrogen sorption in rht-MOF-1: identifying the binding sites through explicit polarization and quantum rotation calculations

    KAUST Repository

    Pham, Tony

    2014-01-01

    Grand canonical Monte Carlo (GCMC) simulations of hydrogen sorption were performed in rht-MOF-1, a metal-organic framework (MOF) that consists of isophthalate groups joined by copper paddlewheel clusters and Cu3O trimers through tetrazolate moeities. This is a charged rht-MOF that contains extra-framework nitrate counterions within the material. For the simulations performed herein, excellent agreement with experiment was achieved for the simulated hydrogen sorption isotherms and calculated isosteric heat of adsorption, Qst, values only when using a polarizable potential. Thermodynamic agreement is demonstrated via comparing to experimental isotherms and binding sites are revealed by combining simulation and inelastic neutron scattering (INS) data. Simulations involving explicit many-body polarization interactions assisted in the determination of the binding sites in rht-MOF-1 through the distribution of the induced dipoles that led to strong adsorbate interactions. Four distinct hydrogen sorption sites were determined from the polarization distribution: the nitrate ions located in the corners of the truncated tetrahedral cages, the Cu2+ ions of the paddlewheels that project into the truncated tetrahedral and truncated octahedral cages (Cu1 ions), the Cu2+ ions of the Cu3O trimers (Cu3 ions), and the sides of the paddlewheels in the cuboctahedral cage. The simulations revealed that the initial sorption sites for hydrogen in rht-MOF-1 are the nitrate ions; this site corresponds to the high initial Qst value for hydrogen (9.5 kJ mol-1) in the MOF. The radial distribution functions, g(r), about the Cu2+ ions at various loadings revealed that the Cu1 ions are the preferred open-metal sorption sites for hydrogen at low loading, while the Cu3 ions become occupied at higher loadings. The validation of the aforementioned sorption sites in rht-MOF-1 was confirmed by calculating the two-dimensional quantum rotational levels about each site and comparing the levels to the

  11. Molecular simulation of polycyclic aromatic hydrocarbon sorption to black carbon

    NARCIS (Netherlands)

    Haftka, J.J.H.; Parsons, J.R.; Govers, H.A.J.

    2009-01-01

    Strong sorption of hydrophobic organic contaminants to soot or black carbon (BC) is an important environmental process limiting the bioremediation potential of contaminated soils and sediments. Reliable methods to predict BC sorption coefficients for organic contaminants are therefore required. A

  12. Water sorption and transport in dry crispy bread crust

    NARCIS (Netherlands)

    Meinders, M.B.J.; Nieuwenhuijzen, van N.H.; Tromp, R.H.; Hamer, R.J.; Vliet, van T.

    2010-01-01

    Water sorption and dynamical properties of bread crust have been studied using gravimetric sorption experiments. Water uptake and loss were followed while relative humidity (RH) was stepwise in- or decreased (isotherm experiment) or varied between two adjusted values (oscillatory experiment).

  13. Water Sorption and Transport in Dry, Crispy Bread Crust

    NARCIS (Netherlands)

    Meinders, M.B.J.; Nieuwenhuijzen, N.H. van; Tromp, R.H.; Hamer, R.J.; Vliet, T. van

    2010-01-01

    Water - sorption and dynamic properties of bread crust have been studied in gravimetric sorption experiments. Water uptake and loss were measured while relative humidity (RH) was stepwise increased or decreased (isotherm experiment) or varied between two adjusted values (oscillatory experiment).

  14. Site-specific functionalization for chemical speciation of Cr(III) and Cr(VI) using polyaniline impregnated nanocellulose composite: equilibrium, kinetic, and thermodynamic modeling

    Science.gov (United States)

    Jain, Priyanka; Varshney, Shilpa; Srivastava, Shalini

    2017-07-01

    Site-specific functionalizations are the emergent attention for the enhancement of sorption latent of heavy metals. Limited chemistry has been applied for the fabrication of diafunctionalized materials having potential to tether both environmentally stable oxidation states of chromium (Cr(III) and Cr(VI). Polyaniline impregnated nanocellulose composite (PANI-NCC) has been fabricated using click chemistry and explored for the removal of Cr(III) and Cr(VI) from hydrological environment. The structure, stability, morphology, particle size, surface area, hydrophilicity, and porosity of fabricated PANI-NCC were characterized comprehensively using analytical techniques and mathematical tools. The maximum sorption performance of PANI-NCC was procured for (Cr(III): 47.06 mg g-1; 94.12 %) and (Cr(VI): 48.92 mg g-1; 97.84 %) by equilibrating 0.5 g sorbent dose with 1000 mL of 25 mg L-1 chromium conc. at pH 6.5 and 2.5 for Cr(III) and Cr(VI), respectively. The sorption data showed a best fit to the Langmuir isotherm and pseudo-second-order kinetic model. The negative value of ∆ G° (-8.59 and -11.16 kJ mol-1) and ∆ H° (66.46 × 10-1 and 17.84 × 10-1 kJ mol-1), and positive value of ∆ S° (26.66 and 31.46 J mol-1K-1) for Cr(III) and Cr(VI), respectively, reflect the spontaneous, feasibility, and exothermic nature of the sorption process. The application of fabricated PANI-NCC for removing both the forms of chromium in the presence of other heavy metals was also tested at laboratory and industrial waste water regime. These findings open up new avenues in the row of high performance, scalable, and economic nanobiomaterial for the remediation of both forms of chromium from water streams.

  15. Adsorption Process and Mechanism of Cd(Ii and Cr(Vi Removal from Aqueous Solution by Waste Marigold Flowers

    Directory of Open Access Journals (Sweden)

    Monoj Kumar Mondal

    2015-12-01

    Full Text Available In this work, waste marigold flowers from Temple were used as adsorbent to remove cadmium (II and chromium (VI ions from aqueous solutions. Influences of initial heavy metal concentrations, contact time, adsorbent dose, temperature and initial pH on removal of cadmium (II and chromium (VI ions were studied under batch mode of operation. Both the adsorption process of cadmium (II and chromium (VI followed pseudo-second order kinetics. Adsorption isotherm parameters of cadmium (II and chromium (VI on dried marigold flower were determined using Langmuir and Freundlich models. Thermodynamic parameters depicted that the process was spontaneous and exothermic under experimental conditions. The maximum removal efficiency of cadmium (II was obtained as 83% at contact time 75 min and pH 5. The maximum removal efficiency of chromium (VI was found as 96% at contact time 105 min and pH 3. Dried marigold flower showed active reusability characteristics upto three consecutive adsorption-desorption cycles.

  16. Sorption of the organic cation metoprolol on silica gel from its aqueous solution considering the competition of inorganic cations.

    Science.gov (United States)

    Kutzner, Susann; Schaffer, Mario; Börnick, Hilmar; Licha, Tobias; Worch, Eckhard

    2014-05-01

    Systematic batch experiments with the organic monovalent cation metoprolol as sorbate and the synthetic material silica gel as sorbent were conducted with the aim of characterizing the sorption of organic cations onto charged surfaces. Sorption isotherms for metoprolol (>99% protonated in the tested pH of around 6) in competition with mono- and divalent inorganic cations (Na(+), NH4(+), Ca(2+), and Mg(2+)) were determined in order to assess their influence on cation exchange processes and to identify the role of further sorptive interactions. The obtained sorption isotherms could be described well by an exponential function (Freundlich isotherm model) with consistent exponents (about 0.8). In general, a decreasing sorption of metoprolol with increasing concentrations in inorganic cations was observed. Competing ions of the same valence showed similar effects. A significant sorption affinity of metoprolol with ion type dependent Freundlich coefficients KF,0.77 between 234.42 and 426.58 (L/kg)(0.77) could still be observed even at very high concentrations of competing inorganic cations. Additional column experiments confirm this behavior, which suggests the existence of further relevant interactions beside cation exchange. In subsequent batch experiments, the influence of mixtures with more than one competing ion and the effect of a reduced negative surface charge at a pH below the point of zero charge (pHPZC ≈ 2.5) were also investigated. Finally, the study demonstrates that cation exchange is the most relevant but not the sole mechanism for the sorption of metoprolol on silica gel. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Protostars and Planets VI

    Science.gov (United States)

    Beuther, Henrik; Klessen, Ralf S.; Dullemond, Cornelis P.; Henning, Thomas

    star and planet formation. They are used by students to dive into new topics, and they are much valued by experienced researchers as a comprehensive overview of the field with all its interactions. We hope that you will enjoy reading (and learning from) this book as much as we do. The organization of the Protostars and Planets conference was carried out in close collaboration between the Max Planck Institute for Astronomy and the Center for Astronomy of the University Heidelberg, with generous support from the German Science Foundation. This volume is a product of effort and care by many people. First and foremost, we want to acknowledge the 250 contributing authors, as it is only due to their expertise and knowledge that such a comprehensive review compendium in all its depth and breadth is possible. The Protostars and Planets VI conference and this volume was a major undertaking, with support and contributions by many people and institutions. We like to thank the members of the Scientific Advisory Committee who selected the 38 teams and chapters out of more than 120 submitted proposals. Similarly, we are grateful to the reviewers, who provided valuable input and help to the chapter authors. The book would also not have been possible without the great support of Renée Dotson and other staff from USRA’s Lunar and Planetary Institute, who handled the detailed processing of all manuscripts and the production of the book, and of Allyson Carter and other staff from the University of Arizona Press. We are also grateful to Richard Binzel, the General Editor of the Space Science Series, for his constant support during the long process, from the original concept to this final product. Finally, we would like to express a very special thank you to the entire conference local organizing committee, and in particular, Carmen Cuevas and Natali Jurina, for their great commitment to the project and for a very fruitful and enjoyable collaboration.

  18. Nanoporous functional organosilicas for sorption of toxic ions

    Science.gov (United States)

    Belyakova, L. A.; Lyashenko, D. Yu.

    2014-03-01

    The chemical immobilization of β-cyclodextrin and its bromoacetyl and thiosemicarbazidoacetyl functional derivatives on the surface of highly disperse amorphous nanoporous silica was performed. β-Cyclodextrin-containing silicas were found to have high affinity to mercury(II), cadmium(II), and zinc(II) cations. Supramolecular surface structures formed whose chemical composition depends on the nature of the sorbed cations and the functional substituents in the attached β-cyclodextrin molecules.

  19. Sorption of Lead (II Ions on Activated Coconut Husk

    Directory of Open Access Journals (Sweden)

    Amin Jahangard

    2016-10-01

    Full Text Available Background: In recent years, various toxic chemicals/compounds have been widely detected at dangerous levels in drinking water in many parts of the world posing a variety of serious health risks to human beings. One of these toxic chemicals is lead, so this paper aimed to evaluate of efficiency coconut husk as cheap adsorbent for removal lead under different conditions. Methods: In the spring of 2015, batch studies were performed in laboratory (Branch of Hamadan, Islamic Azad University, to evaluate the influences of various experimental parameters like pH, initial concentration, adsorbent dosage, contact time and the effect of temperature on the adsorption capacity of coconut husk for removal lead from aqueous solution. Results: Optimum conditions for Pb (II removal were pH 6, adsorbent dosage 1g/100ml of solution and equilibrium time 120 min. The adsorption isotherm was also affected by temperature since the adsorption capacity was increased by raising the temperature from 25 to 45 °C. The equilibrium adsorption isotherm was better described by Freuindlich adsorption isotherm model. Conclusion: It is evident from the literature survey that coconut-based biosorbents have shown good potential for the removal of various aquatic pollutants. Coconut husk-based activated carbon can be a promising adsorbent for removal of Pb from aqueous solutions.

  20. Sorption of toxic metal ions in aqueous environment using ...

    African Journals Online (AJOL)

    2012-03-08

    Mar 8, 2012 ... electrode was calibrated for a strong acid–strong base reaction by the Gran method (Gran, 1952) and Eº value of the reaction was obtained using the GLEE software (Gans and O'Sullivan,. 2000).The pKw value of 13.83±0.01, obtained in 0.1 M tetra- methylammonium chloride (TMACl) as an ionic medium,.

  1. Sorption of toxic metal ions in aqueous environment using ...

    African Journals Online (AJOL)

    carbodithioate and imidazole-1-carbodithioate were employed as sorbents for heavy metals from aqueous environments. The equilibrating time, initial metal concentrations and sorbent mass for optimal adsorption were 40 min, 5 mg/ℓ and 8 mg, ...

  2. Sorption of toxic metal ions in aqueous environment using ...

    African Journals Online (AJOL)

    PROMOTING ACCESS TO AFRICAN RESEARCH ... Log in or Register to get access to full text downloads. ... Browse By Category · Browse Alphabetically · Browse By Country · List All Titles · Free To Read Titles This Journal is Open Access.

  3. Gas Sorption and Storage Properties of Calixarenes

    Energy Technology Data Exchange (ETDEWEB)

    Patil, Rahul S.; Banerjee, Debasis; Atwood, Jerry L.; Thallapally, Praveen K.

    2016-12-01

    Calixarenes, a class of organic macrocyclic molecules have shown interesting gas sorption properties towards industrially important gases such as carbon di-oxide, hydrogen, methane and acetylene. These macrocycles are involved in weak van der Waals interaction to form multidimensional supramolecular frameworks. The gas-diffusion and subsequent sorption occurs due to a cooperative behavior between neighboring macrocycles. Furthermore, the flexibility at the upper rim functional group also plays a key role in the overall gas uptake of calixarene. In this book chapter, we give a brief account of interaction and diffusion of gases in calixarene and selected derivatives.

  4. Sorption Properties of Some Romanian Gingerbread

    Directory of Open Access Journals (Sweden)

    Tulbure Anca

    2014-06-01

    Full Text Available Water activity of gingerbread is very important for keeping the product freshness and shelf life. Water activity is influenced by composition, water content and temperature. The water content of gingerbread could vary according with storage condition. i.e. rH. 11 gingerbread samples were analysed. The water content and water activity lies between 7.0 and 12.6% and respectively 0.590 and 0.715. The sorption isotherms were determined at 30°C by gravimetric method. The moisture sorption is influenced by composition, especially sweeteners and humectants. Honey and invert sugar have the same impact on gingerbread higroscopicity.

  5. Lithium sorption properties of HMnO in seawater and wastewater.

    Science.gov (United States)

    Park, HyunJu; Singhal, Naresh; Jho, Eun Hea

    2015-12-15

    The lithium concentration in seawater is 0.17 mg/L, which is very low, but the overall quantity is approximately 2.5 × 10(14) kg. Therefore, seawater, which contains a vast amount of lithium, could be a major alternative source that might supply the rising demand for lithium. This research was undertaken to evaluate the feasibility of a manganese oxide (HMnO) adsorbent, which was produced after leaching lithium from lithium manganese oxide, for lithium collection from seawater. The HMnO was synthesized and deformed to a plastic after wet blending of manganese oxide and lithium hydroxide, and subsequently, the influence of pH, sorption isotherms, sorption rates, sorption energies, and effects of the co-ions were measured. Thermodynamic parameters such as ΔG°, ΔH°, and ΔS° indicated that the nature of the lithium sorption was both spontaneous and endothermic. The used HMnO could be regenerated by washing it with an HCl solution. The results demonstrated that HMnO could be effectively used for the collection of lithium from seawater with good selectivity. Copyright © 2015 Elsevier Ltd. All rights reserved.

  6. An assessment of strontium sorption onto bentonite buffer material in waste repository.

    Science.gov (United States)

    Pathak, Pankaj

    2017-03-01

    In the present study, changes occurring in sorption characteristics of a representative bentonite (WIn-BT) exposed to SrCl 2 (0.001-0.1 M) under the pH range of 1-13 were investigated. Such interaction revealed a significant variation in surface charge density and binding energy of ions with respect to bentonite, and alteration in their physicochemical properties viz., specific surface area, cation exchange capacity, thermal and mechanical behaviour were observed. The distribution coefficients (k d ) calculated for sorption onto virgin (UCBT) and contaminated bentonite (CBT) indicated a greater influence of mineralogical changes occurred with variance of pH and strontium concentration. Notably, the sorption mechanism clearly elucidates the effect of structural negative charge and existence of anionic metal species onto CBT, and depicted the reason behind significant k d values at highly acidic and alkaline pH. The maximum k d of UCBT and CBT (0.001M SrCl2) were 8.99 and 2.92 L/kg, respectively, at the soil pH 8.5; whereas it was 2.37 and 1.23 L/kg at pH 1 for the CBT (0.1M SrCl2) and CBT (0.01M SrCl2) , respectively. The findings of this study can be useful to identify the physicochemical parameters of candidate buffer material and sorption reversibility in waste repository.

  7. Understanding hydrogen sorption in a metal-organic framework with open-metal sites and amide functional groups

    KAUST Repository

    Pham, Tony T.

    2013-05-09

    Grand canonical Monte Carlo (GCMC) studies of the mechanism of hydrogen sorption in an rht-MOF known as Cu-TPBTM are presented. The MOF is a decorated/substituted isostructural analogue to the unembellished rht-MOF, PCN-61, that was studied previously [ Forrest, K. A.J. Phys. Chem. C 2012, 116, 15538-15549. ]. The simulations were performed using three different hydrogen potentials of increasing complexity. Simulated hydrogen sorption isotherms and calculated isosteric heat of adsorption, Qst, values were in excellent agreement with the reported experimental data for only a polarizable model in one of four experimentally observed crystal structure configurations. The study demonstrates the ability of modeling to distinguish the differential sorption of distinct strucures; one configuration is found to be dominant due to favorable interactions with substrates. In addition, it was discovered that the presence of polar amide groups had a significant effect on the electrostatics of the Cu2+ ions and directs the low-pressure physisorption of hydrogen in the MOF. This is in contrast to what was observed in PCN-61, where an exterior copper ion had a higher relative charge and was the favored loading site. This tunability of the electrostatics of the copper ions via chemical substitution on the MOF framework can be explained by the presence of the negatively charged oxygen atom of the amide group that causes the interior Cu2+ ion to exhibit a higher positive charge through an inductive effect. Further, control simulations, taking advantage of the flexibility afforded by theoretical modeling, include artificially modified charges for both Cu2+ ions chosen equal to or with a higher charge on the exterior Cu2+ ion. This choice resulted in distinctly different hydrogen sorption characteristics in Cu-TPBTM with no direct sorption on the open-metal sites. Thus, this study demonstrates both the tunable nature of MOF platforms and the possibility for rational design of sorption

  8. VI Tallinna arhitektuuritriennaal / Leonhard Lapin

    Index Scriptorium Estoniae

    Lapin, Leonhard, 1947-

    2005-01-01

    15.-17. IX Tallinnas Niguliste kirikus toimuval VI Tallinna arhitektuuritriennaalil esinevad inglise arhitektuurikriitik Peter Davey, šveitsi arhitekt Peter Zumthor, soome arhitekt Juha Leviskä, eesti arhitekt Vilen Künnapu, eesti kunstiajaloolane Juhan Maiste jt. Külastatakse KUMU, tutvutab autor Pekka Vapaavuori

  9. (VI) oxide in acetic acid

    African Journals Online (AJOL)

    The oxidation of cyclohexene by chromium (VI) oxide in aqueous and acetic media was studied. The reaction products were analysed using infra red (IR) and gas chromatography coupled with mass (GC/MS) spectroscopy. The major products of the oxidation reaction in acetic acid medium were cyclohexanol, ...

  10. Sorption of perfluorooctane sulfonate to carbon nanotubes in aquatic sediments

    NARCIS (Netherlands)

    Kwadijk, C.J.A.F.; Velzeboer, I.; Koelmans, A.A.

    2013-01-01

    To date, sorption of organic compounds to nanomaterials has mainly been studied for the nanomaterial in its pristine state. However, sorption may be different when nanomaterials are buried in sediments. Here, we studied sorption of Perfluorooctane sulfonate (PFOS) to sediment and to sediment with 4%

  11. suitability of murram for phosphorus sorption in constructed wetlands

    African Journals Online (AJOL)

    Mimi

    ABSTRACT: The study of Moshi Pumice's phosphorus sorption behaviours and properties was carried out in laboratory scale where by 1-2 mm, 2-4 mm and 4-8 mm grains were tested using batch experiments. The results show that Moshi Pumice has high phosphorus sorption capacity. The sorption capacity for the Moshi ...

  12. An improved experimental and regression methodology for sorption isotherms

    NARCIS (Netherlands)

    Quirijns, E.J.; Boxtel, van A.J.B.; Loon, van W.K.P.; Straten, van G.

    2005-01-01

    Sorption isotherms of corn and starch cylinders with immobilised catalase are experimentally determined at different temperatures for use in drying models in optimal control studies. This application of the sorption isotherm requires an accurate prediction of the sorption data at different

  13. Attenuation of polychlorinated biphenyl sorption to charcoal by humic acids

    NARCIS (Netherlands)

    Koelmans, A.A.; Meulman, B.; Meijer, T.; Jonker, M.T.O.

    2009-01-01

    Strong sorption to black carbon may limit the environmental risks of organic pollutants, but interactions with cosorbing humic acid (HA) may interfere. We studied the attenuative effect of HA additions on the sorption of polychlorinated biphenyls (PCBs) to a charcoal. "Intrinsic" sorption to

  14. Attenuation of polychlorinated biphenyl sorption to charcoal by humic acids.

    NARCIS (Netherlands)

    Koelmans, A.A.; Meulman, B.; Meijer, T.; Jonker, M.T.O.|info:eu-repo/dai/nl/175518793

    2009-01-01

    Strong sorption to black carbon may limit the environmental risks of organic pollutants, but interactions with cosorbing humic acid (HA) may interfere. We studied the attenuative effect of HA additions on the sorption of polychlorinated biphenyls (PCBs) to a charcoal. "Intrinsic" sorption to

  15. Investigations on the molecular structure of water dissolved and hematite-sorbed uranium(VI) complexes with aliphatic (hydroxo-) carboxylic acids. Combination of several spectroscopic techniques with factor analysis and quantum chemical calculations; Untersuchungen zur Struktur von wassergeloesten und an Haematit sorbierten Uran(VI)-Komplexen mit aliphatischen (Hydroxy-) Carbonsaeuren. Kombination verschiedener spektroskopischer Methoden mit Faktorenanalyse und quantenchemischen Berechnungen

    Energy Technology Data Exchange (ETDEWEB)

    Lucks, Christian

    2013-04-23

    This study is focussed on throwing light on the structures of uranium(VI) complexes with aliphatic (hydroxy-) carboxylic acids and on the structures of the sorption complexes on the iron mineral hematite in presence and absence of organic acids. The ternary system of hematite, uranium(VI), and organic ligand is very complicated, thus it is necessary to decompose it in binary systems. The results within these binary systems are used to better understand the complicated ternary system. Based on the comprehensive investigations on the aqueous uranium(VI) complexes, it is now possible to draw inferences from the structure of the carboxylic acid about the structure of the formed uranium(VI) complex in dependence of the pH. At first it has to be mentioned that uranium(VI) commonly gives pentagonal bipyramidal complexes. The pentaaquauranylion is formed by two axial oxygen atoms (O{sub ax}) at a distance of 1.76 Aa and five equatorial oxygen atoms (O{sub eq}) at 2.40 Aa stemming from coordinated water molecules. Due to complexation with organic ligands water is replaced by the ligand, thus the interatomic distances change. The results gained during all these investigations can help to better understand the interaction of uranium(VI) and carboxylic acids, and beyond that the sorption of uranium(VI) on hematite in the presence of carboxylic acids. Structures of the aqueous and sorption complexes are proposed. All these findings support the ongoing research on the transport behaviour of radioactive matter and may lead to more reliable risk assessment in connection with the permanent disposal of nuclear waste and the residues of uranium mining.

  16. 29 CFR 1926.1126 - Chromium (VI).

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Chromium (VI). 1926.1126 Section 1926.1126 Labor... Chromium (VI). (a) Scope. (1) This standard applies to occupational exposures to chromium (VI) in all forms... objective data demonstrating that a material containing chromium or a specific process, operation, or...

  17. 29 CFR 1915.1026 - Chromium (VI).

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Chromium (VI). 1915.1026 Section 1915.1026 Labor... § 1915.1026 Chromium (VI). (a) Scope. (1) This standard applies to occupational exposures to chromium (VI... cement; or (4) Where the employer has objective data demonstrating that a material containing chromium or...

  18. Sorption of Am(III) on attapulgite/iron oxide magnetic composites. Effect of pH, ionic strength and humic acid

    Energy Technology Data Exchange (ETDEWEB)

    Yu, T. [Lanzhou Univ., Gansu (China). Radiochemistry Lab.; East China Institute of Technology, Fuzhou, Jiangxi (China). College of Chemistry, Biology and Materials Science; Fan, Q.H.; Wu, W.S. [Lanzhou Univ., Gansu (China). Radiochemistry Lab.; Lanzhou Univ., Gansu (China). State Key Laboratory of Applied Chemistry; Liu, S.P.; Pan, D.Q.; Zhang, Y.Y.; Li, P. [Lanzhou Univ., Gansu (China). Radiochemistry Lab.

    2012-07-01

    Attapulgite/iron oxide magnetic (ATP/IOM) composites was prepared, and the sorption behavior of Am(III) on that composites was studied as a function of pH, ionic strength, the solid-to-liquid ratio (m/V), contact time, and the concentration of Am(III) under ambient conditions using batch technique. The time to achieve the sorption equilibrium was less than 5 h. The sorption of Am(III) on ATP/IOM composites was strongly affected by pH and ionic strength. Though ion exchange reaction contributed to Am(III) sorption over low pH range and low ionic strength, the sorption was mainly dominated by surface complexion (i.e., outer- and/or inner-sphere complexes) in the whole observed pH range. In the presence of humic acid (HA), the sorption edge of Am(III) on ATP/IOM composites obviously shifted to lower pH; but Am(III) sorption gradually became weak after pH exceeded 4, which may be mainly in terms of the soluble complexes of HA-Am(III). (orig.)

  19. Effect of humic acid, fulvic acid, pH, ionic strength and temperature on {sup 63}Ni(II) sorption to MnO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Sheng, G.; Wang, X. [School of Nuclear Science and Engineering, North China Electric Power Univ., BJ (China); Key Lab. of Novel Thin Film Solar Cells, Inst. of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Hu, J.; Yang, S.; Ren, X.; Li, J. [Key Lab. of Novel Thin Film Solar Cells, Inst. of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Jin, H. [National Synchrotron Radiation Lab., Univ. of Science and Technology of China, Hefei, AH (China); Chen, Y. [School of Nuclear Science and Engineering, North China Electric Power Univ., BJ (China)

    2010-07-01

    The effects of pH, ionic strength, temperature, humic acid (HA) and fulvic acid (FA) on the sorption of radionuclide {sup 63}Ni(II) to MnO{sub 2} have been investigated by using batch techniques. The results indicated that the sorption of {sup 63}Ni(II) on MnO{sub 2} is obviously dependent on pH values but independent of ionic strength. The presence of HA/FA strongly enhances the sorption of {sup 63}Ni(II) on MnO{sub 2} at low pH values, whereas reduces {sup 63}Ni(II) sorption at high pH values. The sorption of {sup 63}Ni(II) on MnO{sub 2} is attributed to inner-sphere surface complexation rather than outer-sphere surface complexation or ion exchange. The diffuse layer model (DLM) is used to simulate the experimental data well with the aid of FITEQL 3.2. The thermodynamic parameters ({delta}H{sup 0}, {delta}S{sup 0}, {delta}G{sup 0}) are also calculated from the temperature dependent sorption isotherms, and the results suggest that the sorption of {sup 63}Ni(II) on MnO{sub 2} is a spontaneous and endothermic process. (orig.)

  20. Microporous Carbon Disks For Sorption Refrigerators

    Science.gov (United States)

    Munukutla, Lakshmi V.; Moore, Mark R.

    1993-01-01

    Slow, carefully controlled pyrolysis found to turn polyvinylidene chloride disks into carbon disks having small pores and large surface areas. Disks exhibit high adsorptivities making them useful in krypton-sorption refrigerators. Carbons made from polyvinylidene chloride have greater adsorptive capacities. Thermal instability controlled and variability of product reduced by careful control of rates of heating, heating times, and rate of final cooling.

  1. A Sorption Hysteresis Model For Cellulosic Materials

    DEFF Research Database (Denmark)

    Frandsen, Henrik Lund; Damkilde, Lars

    2006-01-01

    The equilibrium concentration of adsorbed water in cellulosic materials is dependent on the history of the variations of vapor pressure in the ambient air, i.e. sorption hysteresis. Existing models to describe this phenomenon such as the independent domain theory have numerical drawbacks and/or i...

  2. Methanol{2-methoxy-6-[(2-oxidopropyliminomethyl]phenolato}dioxidomolybdenum(VI

    Directory of Open Access Journals (Sweden)

    Helen Stoeckli-Evans

    2009-12-01

    Full Text Available In the structure of the title compound, [Mo(C11H13NO3O2(CH3OH], the MoVI ion is octahedrally coordinated by two oxide O atoms, the N atom and two deprotonated OH groups of the tridentate Schiff base ligand 2-methoxy-6-[(2-oxidopropyliminomethyl]phenolate and by a methanol O atom. In the crystal structure, two complexes are linked via O—H...O hydrogen bonds, yielding a centrosymmetric arrangement involving the methanol hydroxy group and one of the ligand O atoms coordinated to the MoVI ion.

  3. Di-μ-chlorido-bis-[chloridobis(dimethyl sulfoxide)dioxidouranium(VI)].

    Science.gov (United States)

    Takao, Koichiro; Ikeda, Yasuhisa

    2007-12-06

    In the crystal structure of the title compound, [U(2)Cl(4)O(4)(C(2)H(6)OS)(4)], the compound has a centrosymmetric dimeric structure bridged by two chloride anions. Each U(VI) atom is seven-coordinate in a penta-gonal-bipyramidal geometry. In the equatorial plane of the uranyl unit there are two O atoms from non-adjacent dimethyl sulfoxides and three chloride ions (of which two chlorides are bridging). The compound is of inter-est as an anhydrous starting material of the uran-yl(VI) ion.

  4. Evaluation of Cesium, Strontium, and Lead Sorption, Desorption, and Diffusion in Volcanic Tuffs from Frenchman Flat, Nevada Test Site: Macroscopic and Spectroscopic Investigations

    Energy Technology Data Exchange (ETDEWEB)

    Charalambos Papelis; Wooyong Um

    2003-03-01

    The interaction of radionuclides and other contaminants with minerals and other aquifer materials controls the rate of migration of these contaminants in groundwater. The stronger these interactions, the more a radionuclide will be retarded. Processes such as sorption and diffusion often control the migration of inorganic compounds in aquifers. In addition, these processes are often controlled by the nature of ions of interest, the nature of the aquifer materials, and the specific geochemical conditions. Parameters describing sorption and diffusion of radionuclides and other inorganic ions on aquifer materials are used in transport codes to predict the potential for migration of these contaminants into the accessible environment. Sorption and diffusion studies can help reduce the uncertainty of radionuclide transport modeling on the Nevada Test Site (NTS) and other nuclear testing areas. For example, reliable sorption equilibrium constants, obtained under a variety of conditions, can be used to suggest a plausible sorption mechanism and to provide retardation parameters that can be used in transport models. In addition, these experiments, performed under a variety of conditions, can lead to models that can accommodate changing geochemical conditions. Desorption studies can probe the reversibility of reactions and test whether the reversibility assumed by equilibrium models is justified. Kinetic studies can be used to probe the time-dependent limitations of reactions and suggest whether an equilibrium or kinetic model may be more appropriate. Finally, spectroscopic studies can be used to distinguish between different sorption mechanisms, and provide further guidance with respect to model selection.

  5. Water vapor sorption properties of cellulose nanocrystals and nanofibers using dynamic vapor sorption apparatus.

    Science.gov (United States)

    Guo, Xin; Wu, Yiqiang; Xie, Xinfeng

    2017-10-27

    Hygroscopic behavior is an inherent characteristic of nanocellulose which strongly affects its applications. In this study, the water vapor sorption behavior of four nanocellulose samples, such as cellulose nanocrystals and nanofibers with cellulose I and II structures (cellulose nanocrystals (CNC) I, CNC II, cellulose nanofibers (CNF) I, and CNF II) were studied by dynamic vapor sorption. The highly reproducible data including the running time, real-time sample mass, target relative humidity (RH), actual RH, and isotherm temperature were recorded during the sorption process. In analyzing these data, significant differences in the total running time, equilibrium moisture content, sorption hysteresis and sorption kinetics between these four nanocellulose samples were confirmed. It was important to note that CNC I, CNC II, CNF I, and CNF II had equilibrium moisture contents of 21.4, 28.6, 33.2, and 38.9%, respectively, at a RH of 95%. Then, the sorption kinetics behavior was accurately described by using the parallel exponential kinetics (PEK) model. Furthermore, the Kelvin-Voigt model was introduced to interpret the PEK behavior and calculate the modulus of these four nanocellulose samples.

  6. Micro- and Nano-scale Diffusion Domains Acting as Kinetic Controls for U(VI) Release to the Hanford 300-Area Aquifer

    Science.gov (United States)

    Stoliker, D. L.; Hay, M. B.; Davis, J. A.; Zachara, J. M.

    2008-12-01

    The 300-Area of the Hanford reservation, a cold-war era nuclear processing facility, is plagued by long-term elevated concentrations of U(VI) in the underlying aquifer. While the sediment U(VI) concentration is relatively low, it continues to act as a source and sink for the contaminant, allowing for persistent groundwater concentrations well above the maximum contamination limit (MCL). Simple Kd modeling of the attenuation of U(VI) in the aquifer predicted that groundwater U(VI) concentrations would decrease to below the drinking water standard by the year 2002. However, grain-scale morphology of the aquifer material suggests that intra-grain flow paths and mineral coatings, in which sorption complexes and precipitates formed over years of waste disposal, provide a significant kinetic constraint that slows groundwater flushing of the sediments. In order to quantify the impact of diffusion kinetics on the release of U(VI), high-resolution, non-reactive tracer studies were conducted on vadose zone sediments in both column and batch reactors. Systems were equilibrated for long time scales with tritated artificial groundwater and then flushed with flow and stop-flow events included for columns. Previously collected U(VI) release data from batch dissolution/desorption studies is compared with tritium tracer diffusion kinetics as well as porosimetry and detailed microscopy characterization. The micro-scale and nano-scale diffusion regimes, including intra-granular regions as well as mineral coatings, represent a significant potential long-term source of contaminant U(VI). Understanding the physical kinetic limitations coupled with the complex chemistry of U(VI) sorption processes within natural systems is an important step forward in providing information to strengthen field-scale reactive transport simulations.

  7. An ecological new approach for treating Cr(VI)-containing industrial wastewater: Photochemical reduction.

    Science.gov (United States)

    Liu, Jie; Huang, Kun; Xie, Keng; Yang, Ying; Liu, Huizhou

    2016-04-15

    An ecological new approach for photochemical reduction of Cr(VI) in aqueous solution by adding into water-soluble copolymer, polyethylene glycol (PEG), was investigated. Various influences including light intensity, initial solution pH value, PEG molecular weight and initial concentration ratio of PEG to Cr(VI) on photochemical reduction of Cr(VI) were discussed, and a possible reaction mechanism was proposed. Experimental results revealed that Cr(VI) could be reduced to Cr(III) by PEG under sunlight irradiation. The photo-reduction rate of Cr(VI) increased with the decrease of solution pH and PEG molecular weight, but increased with the light intensity. The reduction percentage of Cr(VI) increased with the initial concentration ratio of PEG to Cr(VI). When the initial solution pH value was below 3.0, almost all of Cr(VI) was completely reduced to Cr(III) within 20 min of 50 × 10(3) lux solar irradiation in the presence of PEG. After photo-reduction, PEG and Cr(III) in aqueous solutions could be recovered by adding into a high-concentrated Na2SO4 aqueous solution to induce the formation of a stable PEG-based aqueous biphasic system. By doing so, Na2SO4 in aqueous solution could also be removed. The present work highlights a promising new route for treating the industrial wastewater containing toxic Cr(VI) ions by adding into environmental-friendly PEG for photo-reduction of Cr(VI) to Cr(III), and then salting-out recovery of PEG and removal of Cr(III) in wastewater by adding into another high-salt wastewater, so that the high-salt wastewater could also be treated. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Sorption behaviour of perfluoroalkyl substances in soils.

    Science.gov (United States)

    Milinovic, Jelena; Lacorte, Silvia; Vidal, Miquel; Rigol, Anna

    2015-04-01

    The sorption behaviour of three perfluoroalkyl substances (PFASs), perfluorooctane sulfonic acid (PFOS), perfluorooctanoic acid (PFOA) and perfluorobutane sulfonic acid (PFBS), was studied in six soils with contrasting characteristics, especially in the organic carbon content. Sorption isotherms were obtained by equilibrating the soil samples with 0.01 mol L(-1) CaCl2 solutions spiked with increasing concentrations of the target PFAS. The sorption reversibility of PFASs was also tested for some of the samples. Liquid chromatography coupled to tandem mass spectrometry was used to quantify the target PFASs in the solutions. Both the Freundlich and linear models were appropriate to describe the sorption behaviour of PFASs in soils, and enabled us to derive solid-liquid distribution coefficients (Kd) for each compound in each soil. Kd values increased from 19 to 295 mL g(-1) for PFOS, from 2.2 to 38 mL g(-1) for PFOA and from 0.4 to 6.8 mL g(-1) for PFBS, and were positively correlated with the organic carbon content of the soil. KOC values obtained from the correlations were 710, 96 and 17 mL g(-1) for PFOS, PFOA and PFBS, respectively. Whereas Kd values decreased in the sequence PFOS>PFOA>PFBS, desorption yields were lower than 13% for PFOS, from 24 to 58% for PFOA, and from 32 to 60% for PFBS. This shows that the physicochemical characteristics of PFASs, basically their hydrophobicity, controlled their sorption behaviour in soils, with PFOS being the most irreversibly sorbed PFAS. Copyright © 2014 Elsevier B.V. All rights reserved.

  9. Sorption of niobium on boreal forest soil

    Energy Technology Data Exchange (ETDEWEB)

    Soederlund, Mervi; Hakanen, Martti; Lehto, Jukka [Helsinki Univ. (Finland). Lab. of Radiochemistry

    2015-07-01

    The sorption of niobium (Nb) was investigated on humus and mineral soil samples taken from various depths of a four-metre deep forest soil pit on Olkiluoto Island, southwestern Finland. Mass distribution coefficients, K{sub d}, were determined in batch sorption tests. The steady state of Nb sorption was observed in the mineral soil samples already after one week of equilibration, and sorption decreased with depth from a very high value of 185000 mL/g at 0.7 m to 54000 mL/g at 3.4 m. The reason behind this decrease is probably the tenfold reduction in the specific surface area of the soil at the same depth range. Distribution coefficients were clearly lower in the humus layer (1000 mL/g). The K{sub d} values determined in pure water at a pH range of 4.7-6.5 were at a high level (above 55000 mL/g), but decreased dramatically above pH 6.5, corresponding to the change in the major Nb species from the neutral Nb(OH){sub 5} to the low-sorbing anionic Nb(OH){sub 6}{sup -} and Nb(OH){sub 7}{sup 2-}. However, the K{sub d} values in the model soil solution were in the slightly alkaline range an order of magnitude higher than in pure water, which is probably caused by the formation of calcium niobate surface precipitate or electrostatic interaction between surface-sorbed calcium and solute Nb. Among nine soil constituent minerals kaolinite performed best in retaining Nb in both pure water and model soil solution at pH 8, whereas potassium feldspar showed the poorest sorption. The K{sub d} value for kaolinite was above 500000 mL/g in both solutions, while the respective potassium feldspar values were in the range of 120-220 mL/g.

  10. Modeling Fission Product Sorption in Graphite Structures

    Energy Technology Data Exchange (ETDEWEB)

    Szlufarska, Izabela [University of Wisconsin, Madison, WI (United States); Morgan, Dane [University of Wisconsin, Madison, WI (United States); Allen, Todd [University of Wisconsin, Madison, WI (United States)

    2013-04-08

    The goal of this project is to determine changes in adsorption and desorption of fission products to/from nuclear-grade graphite in response to a changing chemical environment. First, the project team will employ principle calculations and thermodynamic analysis to predict stability of fission products on graphite in the presence of structural defects commonly observed in very high- temperature reactor (VHTR) graphites. Desorption rates will be determined as a function of partial pressure of oxygen and iodine, relative humidity, and temperature. They will then carry out experimental characterization to determine the statistical distribution of structural features. This structural information will yield distributions of binding sites to be used as an input for a sorption model. Sorption isotherms calculated under this project will contribute to understanding of the physical bases of the source terms that are used in higher-level codes that model fission product transport and retention in graphite. The project will include the following tasks: Perform structural characterization of the VHTR graphite to determine crystallographic phases, defect structures and their distribution, volume fraction of coke, and amount of sp2 versus sp3 bonding. This information will be used as guidance for ab initio modeling and as input for sorptivity models; Perform ab initio calculations of binding energies to determine stability of fission products on the different sorption sites present in nuclear graphite microstructures. The project will use density functional theory (DFT) methods to calculate binding energies in vacuum and in oxidizing environments. The team will also calculate stability of iodine complexes with fission products on graphite sorption sites; Model graphite sorption isotherms to quantify concentration of fission products in graphite. The binding energies will be combined with a Langmuir isotherm statistical model to predict the sorbed concentration of fission

  11. Biomineralization of U(VI) phosphate promoted by microbially-mediated phytate hydrolysis in contaminated soils

    Science.gov (United States)

    Salome, Kathleen R.; Beazley, Melanie J.; Webb, Samuel M.; Sobecky, Patricia A.; Taillefert, Martial

    2017-01-01

    The bioreduction of uranium may immobilize a significant fraction of this toxic contaminant in reduced environments at circumneutral pH. In oxic and low pH environments, however, the low solubility of U(VI)-phosphate minerals also makes them good candidates for the immobilization of U(VI) in the solid phase. As inorganic phosphate is generally scarce in soils, the biomineralization of U(VI)-phosphate minerals via microbially-mediated organophosphate hydrolysis may represent the main immobilization process of uranium in these environments. In this study, contaminated sediments were incubated aerobically in two pH conditions to examine whether phytate, a naturally-occurring and abundant organophosphate in soils, could represent a potential phosphorous source to promote U(VI)-phosphate biomineralization by natural microbial communities. While phytate hydrolysis was not evident at pH 7.0, nearly complete hydrolysis was observed both with and without electron donor at pH 5.5, suggesting indigenous microorganisms express acidic phytases in these sediments. While the rate of hydrolysis of phytate generally increased in the presence of uranium, the net rate of inorganic phosphate production in solution was decreased and inositol phosphate intermediates were generated in contrast to similar incubations conducted without uranium. These findings suggest uranium stress enhanced the phytate-metabolism of the microbial community, while simultaneously inhibiting phosphatase production and/or activity by the indigenous population. Finally, phytate hydrolysis drastically decreased uranium solubility, likely due to formation of ternary sorption complexes, U(VI)-phytate precipitates, and U(VI)-phosphate minerals. Overall, the results of this study provide evidence for the ability of natural microbial communities to liberate phosphate from phytate in acidic sediments, possibly as a detoxification mechanism, and demonstrate the potential utility of phytate-promoted uranium

  12. Removal of fluoride from aqueous phase by biosorption onto algal biosorbent Spirogyra sp.-IO2: Sorption mechanism elucidation

    Energy Technology Data Exchange (ETDEWEB)

    Venkata Mohan, S. [Bioengineering and Environmental Centre, Indian Institute of Chemical Technology, Hyderabad 500007 (India)]. E-mail: vmohan_s@yahoo.com; Ramanaiah, S.V. [Bioengineering and Environmental Centre, Indian Institute of Chemical Technology, Hyderabad 500007 (India); Rajkumar, B. [Bioengineering and Environmental Centre, Indian Institute of Chemical Technology, Hyderabad 500007 (India); Sarma, P.N. [Bioengineering and Environmental Centre, Indian Institute of Chemical Technology, Hyderabad 500007 (India)]. E-mail: sarma1950@yahoo.com

    2007-03-22

    This communication presents results pertaining to the adsorptive studies carried out on fluoride removal onto algal biosorbent (Spirogyra IO2). Batch sorption studies were performed and the results revealed that biosorbent demonstrated ability to adsorb the fluoride. Influence of varying the conditions for removal of fluoride, such as the fluoride concentration, the pH of aqueous solution, the dosage of adsorbent, the temperature on removal of fluoride, and the adsorption-desorption studies were investigated. Sorption interaction of fluoride on to algal species obeyed the pseudo first order rate equation. Experimental data showed good fit with the Langmuir's adsorption isotherm model. Fluoride sorption was found to be dependent on the aqueous phase pH and the uptake was observed to be greater at lower pH. Maximum fluoride sorption was observed at operating 30 deg. C operating temperature. Adsorption-desorption of fluoride into inorganic solutions and distilled water was observed and this indicated the combined effect of ion exchange and physical sorption phenomena. Significant changes in the FT-IR spectra was observed after fluoride sorption which is indicative of the participation of surface function groups associated with hydrogen atoms in the carboxylic groups in sorption interaction. From X-ray photoelectron spectroscopy (XPS) analysis a marginal increase in the area for the binding energy peak at 287.4 eV was observed which could be due to the formation of -C-F- bonds. Thermogravimetric (TGA) analysis of the fluoride loaded sorbent showed that the biosorbent underwent three steps decomposition process when heated from 25 to 100 deg. C. The maximum weight loss was observed to be between 200 and 400 deg. C and 700 and 800 deg. C.

  13. The analysis of isotherms of radionuclides sorption by inorganic sorbents

    Science.gov (United States)

    Bykova, E. P.; Nedobukh, T. A.

    2017-09-01

    The isotherm of cesium sorption by an inorganic sorbent based on granulated glauconite obtained in a wide cesium concentrations range was mathematically treated using Langmuir, Freundlich and Redlich-Peterson sorption models. The algorithms of mathematical treatment of experimental data using these models were described; parameters of all isotherms were determined. It was shown that estimating the correctness of various sorption models relies not only on the correlation coefficient values but also on the closeness of the calculated and experimental data. Various types of sorption sites were found as a result of mathematical treatment of the isotherm of cesium sorption. The algorithm was described and calculation of parameters of the isotherm was performed under the assumption that simultaneous sorption on all three types of sorption sites occurs in accordance with Langmuir isotherm.

  14. Removal of toxic heavy metal ions in runoffs by modified alfalfa and juniper

    Science.gov (United States)

    J.S. Han; J.K. Park; S.H. Min

    2000-01-01

    A series of batch isotherm tests was performed with alfalfa and juniper fibers to evaluate the effectiveness in filtering toxic heavy metals from stormwater. The adsorption of the heavy metal ions on the alfalfa and juniper fibers was strongly dependent on the equilibrium pH value of the solution. The change in sorption rate over time showed that two different sorption...

  15. Effect of metal ion concentration on the biosorption of Pb2+ and ...

    African Journals Online (AJOL)

    The influence of initial metal ion concentration of the batch sorption of Pb2+ and Cd2+ onto a low-cost biosorbent was investigated. The experimental results were analysed in terms of Langmuir and Freundlich isotherms. According to the evaluation using Langmuir equation, the monolayer sorption capacity obtained were ...

  16. Hvad bruger vi tiden til?

    DEFF Research Database (Denmark)

    Brichet, Nathalia Sofie; Hastrup, Frida

    2016-01-01

    I denne artikel kaster vi et antropologisk blik på samtidsarkæologi ved at diskutere måder, hvorpå antropologiske analyser kan adressere tid, fortidige hændelser og historiske processer. Vi argumenterer for, at en radikal nutidsorientering er en afgørende kvalitet ved det antropologiske feltarbej...... komplicerer en ide om fortidige (gamle eller nyere) objekter som nogle, der kan udgraves......., hvis sigte det er løbende at generere sit materiale nu og her med henblik på at skabe nye forståelser, historier og forslag til mangeartede sammenhænge. En implikation af dette er, at uanset hvor ’historisk’ et antropologisk materiale end måtte være, må det altid ses som samtidigt og ufærdigt, hvilket...

  17. Role of Brine Chemistry and Sorption in Potential Long-Term Storage of Radioactive Waste in Geologic Salt Formations: Experimental Evaluation of Sorption Parameters

    Science.gov (United States)

    Dittrich, T. M.; Emerson, H. P.; Michael, D. P.; Reed, D. T.

    2016-12-01

    Bedded geologic salt formations have been shown to have many favorable properties for the disposal of radioactive waste (i.e., reducing conditions, fracture healing). Performance assessment (PA) modeling for a 10,000 year period for the Waste Isolation Pilot Plant (WIPP) near Carlsbad, NM have predicted an extremely low risk of radioactive material reaching the surrounding environment after the 100 year period required for creep to seal the waste panels and access shafts. Human intrusion caused by drilling operations for oil and gas exploration is the main pathway of concern for environmental release of radioactive material due to pressurized brine pockets located within the salt formation below the repository. Our work focuses on the long-term capability of salt repositories and the associated geologic media to safely isolate stored radioactive waste from the surrounding environment, even in the event of a human intrusion scenario such as a direct brine release (DBR) due to a drilling operation intersecting a brine pocket. In particular, we are revisiting the degree of conservatism in the estimated sorption partition coefficients (Kds) used in the PA model based on complementary batch and column experimental methods (Dittrich and Reimus, 2016). The main focus of this work is to investigate the role of ionic strength, solution chemistry, and oxidation state (III-VI) in actinide sorption to dolomite rock. Based on redox conditions and solution chemistry expected in the WIPP, possible actinide species include Pu(III), Pu(IV), U(IV), U(VI), Np(IV), Np(V), Am(III), and Th(IV). We will present (1) a conceptual overview of Kd use in the PA model, (2) background and evolution of the Kd ranges used, and (3) results from batch and column experiments and model predictions for Kds with WIPP-relevant geologic media. We will also briefly discuss the challenges of upscaling from lab experiments to field scale predictions, the presence of ligands (e.g., acetate, citrate, EDTA

  18. Removal of americium from aqueous nitrate solutions by sorption onto PC88A-impregnated macroporous polymeric beads.

    Science.gov (United States)

    Pathak, S K; Tripathi, S C; Singh, K K; Mahtele, A K; Kumar, Manmohan; Gandhi, P M

    2014-08-15

    The removal of Am (III) ions from aqueous solutions was studied by solid-liquid extraction using indigenously synthesized Extractant Impregnated Macroporous Polymeric Beads (EIMPBs). These beads were prepared by an in situ phase inversion method using polyethersulfone (PES) as base polymer and 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (PC88A) as an extractant. The synthesized EIMPBs were characterized by FTIR, TGA and SEM techniques. The batch equilibration study using these beads for the uptake of Am (III) was carried out as a function of parameters, like pH, equilibration time, Am (III) concentration, etc. The blank polymeric beads, without PC88A, have shown negligible sorption of Am (III) under the experimental conditions. The experimental data on the sorption behavior of Am (III) on the polymeric beads fitted well in the pseudo-second-order kinetics model. The synthesized polymeric beads exhibited very good sorption capacity for Am (III) at pH 3. The reusability of the beads was also ascertained by repetitive sorption/desorption of Am (III) up to 10 cycles of operation, without any significant change in their sorption characteristics. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. Polyaniline (PANI) modified bentonite by plasma technique for U(VI) removal from aqueous solution

    Science.gov (United States)

    Liu, Xinghao; Cheng, Cheng; Xiao, Chengjian; Shao, Dadong; Xu, Zimu; Wang, Jiaquan; Hu, Shuheng; Li, Xiaolong; Wang, Weijuan

    2017-07-01

    Polyaniline (PANI) modified bentonite (PANI/bentonie) was synthesized by plasma induced polymerization of aniline on bentonite surface, and applied to uptake of uranium(VI) ions from aqueous solution. The as-synthesized PANI/bentonie was characterized by scanning electron microscopy (SEM), powder X-ray diffraction (XRD), thermal gravimetric analysis (TGA), and X-ray photoelectron spectroscopy (XPS). Batch adsorption technique was utilized to investigate the adsorption of U(VI) on bentonite and PANI/bentonite. The adsorption of U(VI) (10 mg/L) on PANI/bentonite surface is fairly depend on solution pH, ionic strength, and temperature in solution. The modified PANI on PANI/bentonite surface significantly enhances its adsorption capability for U(VI). The presence of humic acid (HA) can sound enhance U(VI) adsorption on PANI/bentonite at pH 6.5. According to the thermodynamic parameters, the adsorption of U(VI) on PANI/bentonite surface is a spontaneous and endothermic process. The results highlight the application of PANI/bentonite composites as candidate material for the uptake of trace U(VI) from aqueous solution.

  20. A review of the distribution coefficients of trace elements in soils: influence of sorption system, element characteristics, and soil colloidal properties.

    Science.gov (United States)

    Shaheen, Sabry M; Tsadilas, Christos D; Rinklebe, Jörg

    2013-12-01

    Knowledge about the behavior and reactions of separate soil components with trace elements (TEs) and their distribution coefficients (Kds) in soils is a key issue in assessing the mobility and retention of TEs. Thus, the fate of TEs and the toxic risk they pose depend crucially on their Kd in soil. This article reviews the Kd of TEs in soils as affected by the sorption system, element characteristics, and soil colloidal properties. The sorption mechanism, determining factors, favorable conditions, and competitive ions on the sorption and Kd of TEs are also discussed here. This review demonstrates that the Kd value of TEs does not only depend on inorganic and organic soil constituents, but also on the nature and characteristics of the elements involved as well as on their competition for sorption sites. The Kd value of TEs is mainly affected by individual or competitive sorption systems. Generally, the sorption in competitive systems is lower than in mono-metal sorption systems. More strongly sorbed elements, such as Pb and Cu, are less affected by competition than mobile elements, such as Cd, Ni, and Zn. The sorption preference exhibited by soils for elements over others may be due to: (i) the hydrolysis constant, (ii) the atomic weight, (iii) the ionic radius, and subsequently the hydrated radius, and (iv) its Misono softness value. Moreover, element concentrations in the test solution mainly affect the Kd values. Mostly, values of Kd decrease as the concentration of the included cation increases in the test solution. Additionally, the Kd of TEs is controlled by the sorption characteristics of soils, such as pH, clay minerals, soil organic matter, Fe and Mn oxides, and calcium carbonate. However, more research is required to verify the practical utilization of studying Kd of TEs in soils as a reliable indicator for assessing the remediation process of toxic metals in soils and waters. © 2013 Elsevier B.V. All rights reserved.

  1. Ion imprinted activated carbon solid-phase extraction coupled to flame atomic absorption spectrometry for selective determination of lead ions in environmental samples

    Energy Technology Data Exchange (ETDEWEB)

    Naraghi, Kiyana; Panahi, Homayon Ahmad; Hassani, Amir Hesam [Islamic Azad University, Tehran (Korea, Republic of); Moniri, Elham [Islamic Azad University, Varamin (Iran, Islamic Republic of)

    2014-10-15

    A simple lead ion imprinted sorbent was synthesized by coupling activated carbon with a known metal chelating compound, iminodiacetic acid. The ion imprinted sorbent has been characterized using Fourier transform infrared spectroscopy, elemental analysis and thermogravimetric analysis and subjected for the extraction and determination of trace Pb(II) in environmental water samples. The optimum pH value for sorption of the lead ion was 6.5. The sorption capacity of lead imprinted sorbent was 42.2 mg g{sup −1}. The chelating imprinted sorbent can be reused for five cycles of sorption-desorption without any significant change in sorption capacity. Compared with non-imprinted polymer particles, the lead ion imprinted sorbent showed high adsorption capacity, significant selectivity, good site accessibility for Pb(II). The equilibrium adsorption data of Pb(II) by modified resin were analyzed by Langmuir, Freundlich, Temkin and Redlich-Peterson models.

  2. Regeneration of spent organoclays after the sorption of organic pollutants: A review.

    Science.gov (United States)

    Zhu, Runliang; Zhu, Jianxi; Ge, Fei; Yuan, Peng

    2009-08-01

    Clay minerals modified with organic ions, also known as organoclays, have found applications in a wide range of organic pollution control fields because of their excellent sorption capacity towards organic pollutants. Regeneration of the spent organoclays after the sorption of organic pollutants is of great importance during their application in pollution control. In this review, the reported methods for the regeneration of the spent organoclays are summarized, including biological degradation, photo-assisted oxidation, chemical extraction/desorption, supercritical extraction, thermal desorption, et al. The characteristics and applications of these methods are briefly described. It shows that most of these methods have been developed for regenerating spent organoclays from wastewater treatment. The biological regeneration method, as an in situ, low cost and easy-operating method, is applicable for regenerating spent organoclays not only from wastewater treatment, but also from soil and groundwater remediation.

  3. Derivative spectrophotometric determination of uranium (VI using diacetyl monoxime isonicotinoyl hydrazone (DMIH

    Directory of Open Access Journals (Sweden)

    ChandraSekhar Reddy Gadikota

    2011-08-01

    Full Text Available Uranium (VI forms a yellow coloured water soluble complex with diacetyl monoxime isonicotinoyl hydrazone (DMIH reagent in acidic buffer of pH 3.25 with ?max at 364 nm. The molar absorptivity and sandell’s sensitivity are 1.63 X 10 4 L.mol -1.cm-1 and 0.00307692 µg/cm 2, respectively. The Beer’s law validity range is 1.19–14.28 µg/mL. Uranium (VI forms (M:L 1:1 complex with DMIH and stability constant of the complex is 4.928 X 106 .The derivative spectrophotometric determination of U (VI was carried out by measuring peak height method. The developed derivative spectrophotometric method was employed for the determination of uranium (VI in rock and synthetic samples. The effect of various diverse ions was also studied.

  4. Removal of Cr(VI) from Aqueous Environments Using Micelle-Clay Adsorption

    Science.gov (United States)

    Qurie, Mohannad; Khamis, Mustafa; Manassra, Adnan; Ayyad, Ibrahim; Nir, Shlomo; Scrano, Laura; Bufo, Sabino A.; Karaman, Rafik

    2013-01-01

    Removal of Cr(VI) from aqueous solutions under different conditions was investigated using either clay (montmorillonite) or micelle-clay complex, the last obtained by adsorbing critical micelle concentration of octadecyltrimethylammonium ions onto montmorillonite. Batch experiments showed the effects of contact time, adsorbent dosage, and pH on the removal efficiency of Cr(VI) from aqueous solutions. Langmuir adsorption isotherm fitted the experimental data giving significant results. Filtration experiments using columns filled with micelle-clay complex mixed with sand were performed to assess Cr(VI) removal efficiency under continuous flow at different pH values. The micelle-clay complex used in this study was capable of removing Cr(VI) from aqueous solutions without any prior acidification of the sample. Results demonstrated that the removal effectiveness reached nearly 100% when using optimal conditions for both batch and continuous flow techniques. PMID:24222757

  5. Removal of Cr(VI from Aqueous Environments Using Micelle-Clay Adsorption

    Directory of Open Access Journals (Sweden)

    Mohannad Qurie

    2013-01-01

    Full Text Available Removal of Cr(VI from aqueous solutions under different conditions was investigated using either clay (montmorillonite or micelle-clay complex, the last obtained by adsorbing critical micelle concentration of octadecyltrimethylammonium ions onto montmorillonite. Batch experiments showed the effects of contact time, adsorbent dosage, and pH on the removal efficiency of Cr(VI from aqueous solutions. Langmuir adsorption isotherm fitted the experimental data giving significant results. Filtration experiments using columns filled with micelle-clay complex mixed with sand were performed to assess Cr(VI removal efficiency under continuous flow at different pH values. The micelle-clay complex used in this study was capable of removing Cr(VI from aqueous solutions without any prior acidification of the sample. Results demonstrated that the removal effectiveness reached nearly 100% when using optimal conditions for both batch and continuous flow techniques.

  6. [Study on the sorption behavior of tetracycline onto activated sludge].

    Science.gov (United States)

    Chen, Rui-Ping; Zhang, Li; Yu, Jie; Tao, Yun; Zhang, Zhong-Pin; Li, Ke-Xun; Liu, Dong-Fang

    2012-01-01

    The batch sorption methods were employed to investigate the sorption behavior of tetracycline (TC) on the activated sludge. It was shown that the mixed liquor suspended solids (MLSS) and the initial concentration of TC had great impacts on equilibrium time, adsorption capacity and adsorption rate. Compared with pseudo first-order model, pseudo second-order model showed the better agreement. At 10, 25 degrees C, the Langmuir model was the best isotherm to describe the experimental data for adsorption of TC on activated sludge, and the maximum adsorption capacities were 31.14, 70.95 mg x g(-1) respectively; at 40 degrees C, the linear isotherm confirmed the agreement. The data were also modeled by D-R isotherm to determine the type of adsorption. At 10 degrees C (E was 9.13 kJ x mol(-1)), the dominant type was physical, and at 40 degrees C (E was 7.07 kJ x mol(-1)), the dominant type was chemical. With the temperature increasing, the adsorption capacity increased. Ion exchange is one mechanism for adsorption of TC on activated sludge. When the initial concentrations of TC were 5, 10, 20 mg x L(-1), with the Na+ concentration increasing from 0 mol x L(-1) to 0.1 mol x L(-1), the adsorption capacities decreased by 15.32%, 15.00%, 20.12% respectively. The maximum adsorption capacity was got at pH 6 when pH varied from 5 to 10.

  7. Defluoridation by Bacteriogenic Iron Oxides: Sorption Studies

    Science.gov (United States)

    Evans, K.; Ferris, F.

    2009-05-01

    At concentrations above 1 mg/L, fluoride in drinking water can lead to dental and skeletal fluorosis, a disease that causes mottling of the teeth, calcification of ligaments, crippling bone deformities and many other physiological disorders that can, ultimately, lead to death. Conservative estimates are that fluorosis afflicts tens of millions of people worldwide. As there is no treatment for fluorosis, prevention is the only means of controlling the disease. While numerous defluoridation techniques have been explored, no single method has been found to be both effective and inexpensive enough to implement widely. Our research began in India, with a large-scale geochemical study of the groundwater in a fluoride-contaminated region of Orissa. Having developed a better understanding of the geochemical relationships that exist between fluoride and other parameters present in an affected area, as well as the complex relationships that arise among those parameters that can impact the presence of fluoride, we began investigating certain remediation scenarios involving iron oxides. A common approach to remediation involves the partitioning of fluoride from groundwater by sorption onto a variety of materials, one of the most effective of which is iron oxide whose surface area acts as a scavenger for fluoride. In the presence of iron oxidizing bacteria, the oxidation rate of iron has been shown to be ˜6 times greater than in their absence; fluoride should, therefore, be removed from an aqueous environment by bacteriogenic iron oxides (BIOS) much more quickly than by abiotic iron oxides. Most recently, sorption studies have been conducted using both BIOS and synthetic hydrous ferric oxides in order to compare the behavior between biotic and abiotic sorbents. These studies have provided sorption isotherms that allow comparison of fluoride removed by sorption to BIOS versus synthetic iron oxides. Sorption affinity constants have also been determined, which allow for the

  8. Column study of Cr(VI) removal by cationic hydrogel for in-situ remediation of contaminated groundwater and soil.

    Science.gov (United States)

    Tang, Samuel C N; Yin, Ke; Lo, Irene M C

    2011-07-01

    Column experiments were conducted for examining the effectiveness of the cationic hydrogel on Cr(VI) removal from groundwater and soil. For in-situ groundwater remediation, the effects of background anions, humic acid (HA) and pH were studied. Cr(VI) has a higher preference for being adsorbed onto the cationic hydrogel than sulphate, bicarbonate ions and HA. However, the adsorbed HA reduced the Cr(VI) removal capacity of the cationic hydrogel, especially after regeneration of the adsorbents, probably due to the blockage of adsorption sites. The Cr(VI) removal was slightly influenced by the groundwater pH that could be attributed to Cr(VI) speciation. The 6-cycle regeneration and reusability study shows that the effectiveness of the cationic hydrogel remained almost unchanged. On average, 93% of the adsorbed Cr(VI) was recovered in each cycle and concentrated Cr(VI) solution was obtained after regeneration. For in-situ soil remediation, the flushing water pH had an insignificant effect on the release of Cr(VI) from the soils. Multiple-pulse flushing increased the removal of Cr(VI) from the soils. In contrast, more flushing water and longer operation may be required to achieve the same removal level by continuous flushing. Copyright © 2011 Elsevier B.V. All rights reserved.

  9. The specific sorption of Np(V) on the corundum (α-Al2O3) surface in the presence of trivalent lanthanides Eu(III) and Gd(III): A batch sorption and XAS study.

    Science.gov (United States)

    Virtanen, S; Bok, F; Ikeda-Ohno, A; Rossberg, A; Lützenkirchen, J; Rabung, T; Lehto, J; Huittinen, N

    2016-12-01

    The sorption of pentavalent neptunium, Np(V), on corundum (α-Al2O3) was investigated in the absence and presence of trivalent europium or gadolinium as a competing element under CO2-free conditions. The objective of this study was to investigate how a trivalent metal ion with a higher charge than that of the neptunyl(V) ion would affect the sorption of Np(V) when allowed to adsorb on the mineral surface before the addition of Np(V). Batch sorption experiments conducted as a function of pH (pH-edges) and as a function of Np(V) concentration (isotherms) in the absence and presence of 1×10(-5)M Eu(III) showed no sign of Eu being able to block Np sorption sites. Surface complexation modelling using the diffuse double layer model was applied to the batch data to obtain surface complexation constants for the formed Np(V) complexes on corundum. To account for potential changes occurring in the coordination environment of the neptunium ion in the presence of a trivalent lanthanide, X-ray absorption spectroscopy (XAS) measurements were carried out on the samples containing only Np(V) and Np(V)+Gd(III). The results reveal the presence of a bidentate Np(V) edge-sharing complex on the corundum surface in the absence of Gd(III), while the coordination environment of Np(V) on the corundum surface could be changed when Gd(III) is added to the sample before the sorption of Np(V). Copyright © 2016 Elsevier Inc. All rights reserved.

  10. New low cost sorbents for Cr(VI – batch and column experiments

    Directory of Open Access Journals (Sweden)

    Šillerová H.

    2013-04-01

    Full Text Available The use of agricultural byproducts and industrial biowaste materials has been shown to be an attractive technique for removing Cr(VI from contaminated waste waters. In this study, used brewers draff, peat moss, sawdust, grape stalks and husks were investigated as novel biosorbents for Cr(VI. The material was tested in two different modifications. The material was dried, cut and sieved and part of it was subjected to acid (2 M H2SO4 and alkali (0.5 M NaOH pre-treatments to remove starch, proteins and sugars. Fourier transform infrared rays analysis on solid phase (FTIR-ATR was used to determine the main functional groups that might control the metal uptake. Batch experiments were performed at different pH values (3, 4.5, 6 and at various initial concentration of Cr(VI (25–2012;250 mg L−1. Two equilibrium empirical models, Langmuir and Freundlich, were used to describe Cr(VI adsorption. In order to identify possible reduction processes, ion exchange separation on the AG1-X8 resin was used to separate the anionic Cr(VI and the reduced cationic Cr(III from the aqueous phase after biosorption. As expected, Cr(VI removal was pH-dependent and fitted well both the Langmuir and Freundlich isotherm models. The ion exchange separation showed that Cr(VI reduction had occurred in the solution during biosorption. The efficiency of draff as a biosorbent was comparable (or even higher to highly organic materials (e.g., composted peat showing its potential application for Cr(VI decontamination.

  11. Removal of Cr(VI) from aqueous solution by flocculant with the capacity of reduction and chelation

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Gang, E-mail: gangw99@163.com [School of Environmental and Municipal Engineering, Lanzhou Jiaotong University, Lanzhou, Gansu 730070 (China); Chang, Qing; Han, Xiaoting; Zhang, Mingyue [School of Environmental and Municipal Engineering, Lanzhou Jiaotong University, Lanzhou, Gansu 730070 (China)

    2013-03-15

    Highlights: ► We report a novel flocculant with the properties of reduction and chelation for Cr. ► The removal of Cr(VI) by the flocculant depends highly on pH value. ► Some coexisting ions inhibit Cr (VI) removal, but promote total Cr removal. ► Cr and turbidity can be removed simultaneously in the treated wastewater. ► The interaction mechanism is investigated by FTIR and SEM. -- Abstract: A novel agent polyethyleneimine-sodium xanthogenate (PEX) with the multifunction of reduction, chelation, flocculation and precipitation was synthesized by using polyethyleneimine (PEI), carbon disulfide (CS{sub 2}), and sodium hydroxide (NaOH). The effects of different important parameters, such as pH value, initial Cr(VI) concentration, coexisting ions and turbidity etc., on the removal of chromium from aqueous solution by PEX were investigated in flocculation experiments. The experiments results demonstrated that PEX could efficiently remove Cr(VI) and total Cr (Cr(VI) + Cr(III)) in strongly acidic media. It was proved that the presence of coexisting ions (Na{sup +}, Ca{sup 2+}, F{sup −}, Cl{sup −}, and SO{sub 4}{sup 2−}) in the solution had a little influence on the removal of chromium. Furthermore, it was conformed that Cr(VI) ions and turbidity could be simultaneously removed when water samples contained both Cr(VI) ions and turbidity. Finally, the mechanism of interaction between chromium and PEX was further confirmed by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The results reveal that dithiocarboxylic acid groups on PEX macromolecule play a major role in Cr(VI) reduction and Cr(III) chelation, and the flocs formation is attributed to the interparticle bridging mechanism of PEX.

  12. Isotherm, kinetic, and thermodynamic study of ciprofloxacin sorption on sediments.

    Science.gov (United States)

    Mutavdžić Pavlović, Dragana; Ćurković, Lidija; Grčić, Ivana; Šimić, Iva; Župan, Josip

    2017-04-01

    In this study, equilibrium isotherms, kinetics and thermodynamics of ciprofloxacin on seven sediments in a batch sorption process were examined. The effects of contact time, initial ciprofloxacin concentration, temperature and ionic strength on the sorption process were studied. The K d parameter from linear sorption model was determined by linear regression analysis, while the Freundlich and Dubinin-Radushkevich (D-R) sorption models were applied to describe the equilibrium isotherms by linear and nonlinear methods. The estimated K d values varied from 171 to 37,347 mL/g. The obtained values of E (free energy estimated from D-R isotherm model) were between 3.51 and 8.64 kJ/mol, which indicated a physical nature of ciprofloxacin sorption on studied sediments. According to obtained n values as measure of intensity of sorption estimate from Freundlich isotherm model (from 0.69 to 1.442), ciprofloxacin sorption on sediments can be categorized from poor to moderately difficult sorption characteristics. Kinetics data were best fitted by the pseudo-second-order model (R 2  > 0.999). Thermodynamic parameters including the Gibbs free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) were calculated to estimate the nature of ciprofloxacin sorption. Results suggested that sorption on sediments was a spontaneous exothermic process.

  13. Sorption kinetics and its effects on retention and leaching.

    Science.gov (United States)

    de Wilde, Tineke; Mertens, Jan; Spanoghe, Pieter; Ryckeboer, Jaak; Jaeken, Peter; Springael, Dirk

    2008-06-01

    Sorption of pesticides to substrates used in biopurification systems is important as it controls the system's efficiency. Ideally, pesticide sorption should occur fast so that leaching of the pesticide in the biopurification system is minimized. Although modeling of pesticide transport commonly assumes equilibrium, this may not always be true in practice. Sorption kinetics have to be taken into account. This study investigated the batch sorption kinetics of linuron, isoproturon, metalaxyl, isoxaben and lenacil on substrates commonly used in a biopurification system, i.e. cow manure, straw, willow chopping, sandy loam soil, coconut chips, garden waste compost and peat mix. The first-order sorption kinetics model was fitted to the observed pesticide concentrations versus time resulting in an estimated kinetic rate constant alpha. Sorption appeared to be fast for the pesticides linuron and isoxaben, pesticides which were classified as immobile, while less mobile pesticides displayed an overall slower sorption. However, the substrate does not seem to be the main parameter influencing the sorption kinetics. Coconut chips, which is a substrate with a high organic matter content showed slow sorption for most of the pesticides. The effect of different estimated alpha values on the breakthrough of pesticides through a biopurification system was evaluated using the HYDRUS 1D model. Significant differences in leaching behavior were observed as a result of the obtained differences in sorption kinetics.

  14. Testosterone sorption and desorption: Effects of soil particle size

    Energy Technology Data Exchange (ETDEWEB)

    Qi, Yong, E-mail: yqi01@unomaha.edu [Civil Engineering Dept., University of Nebraska-Lincoln at Omaha Campus, Omaha, NE 68182 (United States); Zhang, Tian C. [Civil Engineering Dept., University of Nebraska-Lincoln at Omaha Campus, Omaha, NE 68182 (United States); Ren, Yongzheng [School of Environmental Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China)

    2014-08-30

    Graphical abstract: - Highlights: • Smaller soil particles have higher sorption and lower desorption rates. • The sorption capacity ranks as clay > silt > sand. • Small particles like clays have less potential for desorption. • Colloids (clays) have high potential to facilitate the transport of hormones in soil–water environments. - Abstract: Soils contain a wide range of particles of different diameters with different mobility during rainfall events. Effects of soil particles on sorption and desorption behaviors of steroid hormones have not been investigated. In this study, wet sieve washing and repeated sedimentation methods were used to fractionate the soils into five ranges. The sorption and desorption properties and related mechanisms of testosterone in batch reactors filled with fractionated soil particles were evaluated. Results of sorption and desorption kinetics indicate that small soil particles have higher sorption and lower desorption rates than that of big ones. Thermodynamic results show the sorption processes are spontaneous and exothermal. The sorption capacity ranks as clay > silt > sand, depending mainly on specific surface area and surface functional groups. The urea control test shows that hydrogen bonding contributes to testosterone sorption onto clay and silt but not on sand. Desorption tests indicate sorption is 36–65% irreversible from clay to sand. Clays have highest desorption hysteresis among these five soil fractions, indicating small particles like clays have less potential for desorption. The results provide indirect evidence on the colloid (clay)-facilitated transport of hormones (micro-pollutants) in soil environments.

  15. Surface complexation modeling or organic acid sorption to goethite

    Energy Technology Data Exchange (ETDEWEB)

    Evanko, C.R.; Dzombak, D.A. [Carnegie Mellon Univ., Pittsburgh, PA (United States). Dept. of Civil and Environmental Engineering

    1999-06-15

    Surface complexation modeling was performed using the Generalized Two-Layer Model for a series of low molecular weight organic acids. Sorption of these organic acids to goethite was investigated in a previous study to assess the influence of particular structural features on sorption. Here, the ability to describe the observed sorption behavior for compounds with similar structural features using surface complexation modeling was investigated. A set of surface reactions and equilibrium constants yielding optimal data fits was obtained for each organic acid over a range of total sorbate concentrations. Surface complexation modeling successfully described sorption of a number of the simple organic acids, but an additional hydrophobic component was needed to describe sorption behavior of some compounds with significant hydrophobic character. These compounds exhibited sorption behavior of some compounds with significant hydrophobic character. These compounds exhibited sorption behavior that was inconsistent with ligand exchange mechanisms since sorption behavior of some compounds with significant hydrophobic character. These compounds exhibited sorption behavior that was inconsistent with ligand exchange mechanisms since sorption did not decrease with increasing total sorbate concentration and/or exceeded surface site saturation. Hydrophobic interactions appeared to be most significant for the compound containing a 5-carbon aliphatic chain. Comparison of optimized equilibrium constants for similar surface species showed that model results were consistent with observed sorption behavior: equilibrium constants were highest for compounds having adjacent carboxylic groups, lower for compounds with adjacent phenolic groups, and lowest for compounds with phenolic groups in the ortho position relative to a carboxylic group. Surface complexation modeling was also performed to fit sorption data for Suwannee River fulvic acid. The data could be described well using reactions and

  16. Thermodynamics and sorption characteristics of Zn(II) onto natural and chemically modified zeolites for agricultural and environmental using

    Science.gov (United States)

    Saltali, K.; Tazebay, N.; Kaya, M.

    2017-10-01

    Zeolites with high porous and cation exchange capacity have been widely used for agricultural and environmental purposes. This study was conducted to assess the thermodynamics and sorption characteristics of chemically modified zeolite (CMZ) from obtained natural zeolite (NZ), and to compare its properties. At first step of the sorption experiment, effects of pH, slurry concentration, stirring time, and heat on Zn removal were determined. Linear Langmuir isotherm was well fitted to data, and maximum sorption capacities ( q max) were calculated as 20.87 and 33.44 mg/g for NZ and CMZ, respectively. Dubinin-Redushkevich (D-R) isotherm showed that the adsorption process was probably controlled by chemical ion-exchange mechanism. The solubility of zinc DTPA should be so directly related to the model of D-R model. Therefore, zeolites can be used as carrier Zn in soils with insufficient zinc arid and semiarid regions. Enthalpy (Δ H°) and entropy (Δ S°) values were positive. The change values of Gibbs free energy (Δ G°) illustrated that the sorption of Zn ions onto zeolites was feasible and spontaneous. From the obtained results, it could be concluded that chemical modification increased q max value of NZ, and the findings indicate clearly the possibility of using NZ and CMZ as Zn carrier in agricultural and also environmental treatments.

  17. Comparative sorption studies of chromate by nano-and-micro sized Fe2O3 particles

    Directory of Open Access Journals (Sweden)

    Muska M.

    2017-06-01

    Full Text Available The comparative adsorption studies of Cr (VI on nano and micro-powder Fe2O3 were investigated using kinetics and batch adsorption techniques. The uptake of chromate onto both the oxides of iron was observed to be dependent on the pH, contact time, temperature, media dosage and concentration of chromate anions. The values of sorption maxima were higher in the case of Fe2O3 nanopowder than the micro-powder which can be ascribed to the high surface area and point of zero charge (PZC of the former oxide. The Dubinin-Radushkivech and Langmuir models were found well fitted for the description of the batch adsorption data. The FTIR studies confirmed that the hexavalent chromium was adsorbed onto both the iron oxides in the form of the Cr2O72−.

  18. Sorption of phenanthrene on agricultural soils

    DEFF Research Database (Denmark)

    Soares, Antonio; Møldrup, Per; Minh, Luong Nhat

    2013-01-01

    Polyaromatic hydrocarbon (PAH) sorption to soil is a key process deciding the transport and fate of PAH, and potential toxic impacts in the soil and groundwater ecosystems, for example in connection with atmospheric PAH deposition on soils. There are numerous studies on PAH sorption in relatively......, 0.25–1-m depth) by the single-point adsorption method. The organic carbon partition coefficient, KOC (liter per kilogram) for topsoils was found generally to fall between the KOC values estimated by the two most frequently used models for PAH partitioning, the Abdul et al. (Hazardous Waste...... & Hazardous Materials 4(3):211–222, 1987) model and Karickhoff et al. (Water Research 13:241–248, 1979) model. A less-recognized model by Karickhoff (Chemosphere 10:833–846, 1981), yielding a KOC of 14,918 L kg−1, closely corresponded to the average measured KOC value for the topsoils, and this model...

  19. Sorption and transport characteristics of composite sorbent

    Science.gov (United States)

    Zinovyev, V. N.; Kazanin, I. V.; Lebiga, V. A.; Pak, A. Y.; Vereshchagin, A. S.; Fomin, V. M.

    2017-10-01

    The study of sorption and transport characteristics of a composite sorbent based on various types of glass microspheres is carried out. In order to carry out this research, an experimental stand has been prepared for measuring sorbent characteristics at specified pressure and temperature values. The technique of carrying out the experiment and processing the experimental data for the purpose of determining the helium permeability of composite sorbents with a filler made of different material: sodium borosilicate glass, silica microspheres, cenospheres has been worked out. The values of the helium permeability of the composite sorbent in the temperature range from 20 to 140 °C are determined. The transport characteristics of the medium formed by the granules of the composite sorbent, as well as the values of the characteristic time of helium sorption by the composite sorbent are found.

  20. Sorption of three synthetic musks by microplastics.

    Science.gov (United States)

    Zhang, Xiaojun; Zheng, Minggang; Wang, Ling; Lou, Yinghua; Shi, Lei; Jiang, Shujun

    2018-01-01

    Microplastics and synthetic musks (SMs) are two typical organic pollutants in the marine environment. In this study, the sorption of three SMs to microplastics in a simulated seawater environment was examined. Tonalide (AHTN), musk xylene (MX), and musk ketone (MK) were the musks investigated, while polypropylene (PP) was used as the microplastic. It was found that the equilibrium sorption time was about 10h and the adsorption kinetics model conformed to a Lagergren adsorption model. The adsorption capacity increased with decreasing particle size. Adsorption reached a peak at 25°C, and the adsorption capacity was not sensitive to the concentration of sodium chloride. There is a need for more research and monitoring of microplastics in the marine environment due to their strong ability to absorb organic pollutants. Copyright © 2017. Published by Elsevier Ltd.

  1. Phosphate sorption characteristics of European alpine soils

    Czech Academy of Sciences Publication Activity Database

    Kaňa, Jiří; Kopáček, Jiří; Camarero, L.; Garcia-Pausas, J.

    2011-01-01

    Roč. 75, č. 3 (2011), s. 862-870 ISSN 0361-5995 R&D Projects: GA ČR(CZ) GA526/09/0567; GA AV ČR(CZ) KJB600960907 Grant - others:EU EMERGE(CZ) EVK1-CT-1999-00032 Institutional research plan: CEZ:AV0Z60170517 Keywords : phosphate sorption * alpine soils * acidification Subject RIV: DJ - Water Pollution ; Quality Impact factor: 1.979, year: 2011

  2. Sorption of sulfuryl fluoride by food commodities.

    Science.gov (United States)

    Sriranjini, Venkata-rao; Rajendran, Somiahnadar

    2008-08-01

    The use of sulfuryl fluoride, a structural fumigant for termite and woodborer control, has recently been expanded to treating stored food commodities and food facilities. There is, however, a lack of data on the sorption of sulfuryl fluoride by food commodities. Knowledge about sorption is important in the context of effective treatment and residues. When sulfuryl fluoride was applied at a dose of 50 g m(-3) to various food commodities (total 68) with 300 g per replicate in 0.75 L gas wash bottles (fumigation chambers) at 25 +/- 1 degrees C, in most cases (81%) the gas concentrations in the free space of the commodities exceeded 50 g m(-3) (range 51-80 g m(-3)) at the end of 24 h exposure. In chambers without the substrate, an average concentration of 49.7 g m(-3) was recorded. About 54% of the commodities showed low-level ( sulfuryl fluoride, 34% showed medium-level (26-50%) sorption and only 12% were highly sorptive (>50%). The latter include white oats (terminal gas concentration 17.8 g m(-3)), some of the decorticated split pulses (24.0-29.3 g m(-3)), chickpea flour (26.3 g m(-3)), dried ginger (29.0 g m(-3)), refined wheat flour (30.3 g m(-3)) and coriander powder (40.5 g m(-3)). In unfumigated control commodities, owing to interfering volatiles, Fumiscope readings in the range 0-13 were noted. Sulfuryl fluoride has the advantage of a low or moderate level of sorption with the majority of the food commodities.

  3. Moisture sorption isotherms of dehydrated whey proteins

    Directory of Open Access Journals (Sweden)

    Suzana Rimac Brnčić

    2010-03-01

    Full Text Available Moisture sorption isotherms describe the relation between the moisture content of the dry material (food and relative humidity of the surrounding environment. The data obtained are important in modelling of drying process conditions, packaging and shelf-life stability of food that will provide maximum retaining of aroma, colour and texture as well as nutritive and biological value. The objective of this research was to establish the equilibrium moisture content and water activity, as well as monolayer value of two commercial powdered whey protein isolates before and after tribomechanical micronisation and enzymatic hydrolysis, respectively. At the same time it was necessary to evaluate the best moisture sorption isotherm equation to fit the experimental data. The equilibrium moisture contents in investigated samples were determined using standard gravimetric method at 20 °C. The range of water activities was 0.11 to 0.75. The monolayer moisture content was estimated from sorption data using Brunauer-Emmett-Teller (BET and Guggenheim-Anderson-de Boer (GAB models. The results have shown that tribomechanically treated whey protein isolates as well as protein hydrolizates had lower monolayer moisture content values as well as higher corresponding water activity. Therefore, in spite of the fact that they have lower moisture content, they can be storage at higher relative humidity compared to untreated samples. BET model gave better fit to experimental sorption data for a water activity range from 0.11-0.54, while GAB model gave the closest fit for a water activity to 0.75.

  4. Bromide oxidation by ferrate(VI): The formation of active bromine and bromate.

    Science.gov (United States)

    Jiang, Yanjun; Goodwill, Joseph E; Tobiason, John E; Reckhow, David A

    2016-06-01

    Ferrate (VI) (abbreviated as Fe(VI)) has long been considered as a green oxidant that does not produce any known hazardous byproducts. However, this work shows that Fe(VI) can slowly oxidize bromide forming active bromine (HOBr/OBr(-)) and bromate, and in natural waters total organic bromine (TOBr) can also be detected. Results showed that the highest levels of active bromine and bromate were formed at lower pHs and in the absence of phosphate. Hydrogen peroxide, which forms from the reaction of Fe(VI) and water, plays an essential role in suppressing bromate formation by reducing active bromine back to bromide. Fe(VI) decomposition products (assumed to be particulate phase Fe(III)) can catalyze the decomposition of hydrogen peroxide by Fe(VI). Phosphate had a substantial inhibiting effect on the formation of active bromine, but less so on bromate formation. The presence of the raw water matrix in natural water suppressed bromate formation. For a natural water spiked with 0.1 mg/L of bromide, the bromate and TOBr concentrations after Fe(VI) oxidation were below 3.0 and 15 μg/L, respectively. No consistent trend regarding the effect of pH or buffer ions on TOBr formation was observed due to the competition between Fe(VI), hydrogen peroxide, and natural organic matter (NOM) for reaction with active bromine. Under environmentally relevant conditions, the formation of bromate and TOBr would not be a problem for Fe(VI) application as their concentration levels are quite low. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Experiments on sorption hysteresis of desiccant materials

    Energy Technology Data Exchange (ETDEWEB)

    Pesaran, A.; Zangrando, F.

    1984-08-01

    Solid desiccant cooling systems take advantage of solar energy for air conditioning. The process involves passing air through a desiccant bed for drying and subsequent evaporative cooling to provide the air conditioning. The desiccant is then regenerated with hot air provided by a gas burner or solar collectors. This performance is limited by the capacity of the desiccant, its sorption properties, and the long-term stability of the desiccant material under cyclic operation conditions. Therefore, we have developed a versatile test facility to measure the sorption properties of candidate solid desiccant materials under dynamic conditions, under different geometrical configurations, and under a broad range of process air stream conditions, characteristic of desiccant dehumidifer operation. We identified a dependence of the sorption processes on air velocity and the test cell aspect ratio and the dynamic hysteresis between adsorption and desorption processes. These experiments were geared to provide data on the dynamic performance of silica gel in a parallel-passage configuration to prepare for tests with a rotary dehumidifier that will be conducted at SERI in late FY 1984. We also recommend improving the accuracy of the isotopic perturbation technique.

  6. Sorption isotherm characteristics of aonla flakes.

    Science.gov (United States)

    Alam, Md Shafiq; Singh, Amarjit

    2011-06-01

    The equilibrium moisture content was determined for un-osmosed and osmosed (salt osmosed and sugar osmosed) aonla flakes using the static method at temperatures of 25, 40,50, 60 and 70 °C over a range of relative humidities from 20 to 90%. The sorption capacity of aonla decreased with an increase in temperature at constant water activity. The sorption isotherms exhibited hysteresis, in which the equilibrium moisture content was higher at a particular equilibrium relative humidity for desorption curve than for adsorption. The hysteresis effect was more pertinent for un-osmosed and salt osmosed samples in comparison to sugar osmosed samples. Five models namely the modified Chung Pfost, modified Halsey, modified Henderson, modified Exponential and Guggenheim-Anderson-de Boer (GAB) were evaluated to determine the best fit for the experimental data. For both adsorption and desorption process of aonla fruit, the equilibrium moisture content of un-osmosed and osmosed aonla samples can be predicted well by GAB model as well as modified Exponential model. Moreover, the modified Exponential model was found to be the best for describing the sorption behaviour of un-osmosed and salt osmosed samples while, GAB model for sugar osmosed aonla samples.

  7. Cysteine-Functionalized Chitosan Magnetic Nano-Based Particles for the Recovery of Light and Heavy Rare Earth Metals: Uptake Kinetics and Sorption Isotherms.

    Science.gov (United States)

    Galhoum, Ahmed A; Mafhouz, Mohammad G; Abdel-Rehem, Sayed T; Gomaa, Nabawia A; Atia, Asem A; Vincent, Thierry; Guibal, Eric

    2015-02-04

    Cysteine-functionalized chitosan magnetic nano-based particles were synthesized for the sorption of light and heavy rare earth (RE) metal ions (La(III), Nd(III) and Yb(III)). The structural, surface, and magnetic properties of nano-sized sorbent were investigated by elemental analysis, FTIR, XRD, TEM and VSM (vibrating sample magnetometry). Experimental data show that the pseudo second-order rate equation fits the kinetic profiles well, while sorption isotherms are described by the Langmuir model. Thermodynamic constants (ΔG°, ΔH°) demonstrate the spontaneous and endothermic nature of sorption. Yb(III) (heavy RE) was selectively sorbed while light RE metal ions La(III) and Nd(III) were concentrated/enriched in the solution. Cationic species RE(III) in aqueous solution can be adsorbed by the combination of chelating and anion-exchange mechanisms. The sorbent can be efficiently regenerated using acidified thiourea.

  8. Evaluation of Cesium, Strontium, and Lead Sorption, Desorption, and Diffusion in Cores from Western Pahute Mesa, Nevada Test Site, based on Macroscopic and Spectroscopic Investigations

    Energy Technology Data Exchange (ETDEWEB)

    Charalambos Papelis; Wooyong Um

    2003-03-01

    The interaction of radionuclides and other contaminants with minerals and other aquifer materials controls the rate of migration of these contaminants in groundwater. The stronger these interactions, the more a radionuclide will be retarded. Processes such as sorption and diffusion often control the migration of inorganic compounds in aquifers. These processes are often controlled by the nature of the ions of interest, the nature of the aquifer materials, and the specific geochemical conditions. Parameters describing sorption and diffusion of radionuclides and other inorganic ions on aquifer materials are used in transport codes to predict the potential for migration of these contaminants into the accessible environment. Sorption and diffusion studies can reduce the uncertainty of radionuclide transport modeling on the Nevada Test Site (NTS) and other nuclear testing areas.

  9. How to examine soil sorption of ionizable organic compounds and avoid varying pH?

    Science.gov (United States)

    Borisover, Mikhail

    2017-04-01

    Multiple natural and anthropogenic organic compounds including new and emerging pollutants undergo ionization in aqueous solutions, and their sorption by soils and sediments is contributed by presence of both molecular and ionized species. Better understanding of environmental fate of organic chemicals requires taking into account interactions of molecular and ionized species with environmental sorbents. A "standard" (and undoubtedly important) procedure for differentiating contributions of molecular and ionized species into the overall soil sorption of an organic compound involves varying pH of solution in batch sorption experiments. However, varying pH is (1) often not possible, without destroying a sorbent, e.g., due to the buffer capacity of soils containing carbonates, (2) difficult for further interpretation, since it changes not only the ionization status of a solute in a solution but also the sorbent structure, e.g., a conformation of organic matter, and/or ionization of surface functional groups, (3) making difficult (or even impossible) to explicitly evaluate the role of dissolved species-bulk water interactions, directly affecting the affinity of a sorbate to distribute between water and a sorbent. Indeed, both molecular and ionized species undergo interactions with the solvent bulk and, at least in the case of the ionized ones, there was no a simple way to quantify organic ion-water interactions and their role in organic ion distribution between soil and water phases. This paper presents a "counter-intuitive" approach to examine sorption interactions of an ionizable compound, without experimenting with varied pH. The approach is based on an idea of replacing an initial state in sorption transfer of an ionizable compound from the solvent bulk to a solvated (hydrated) sorbed state: a traditional coefficient describing distribution of a partially ionized compound between a hydrated sorbent and a co-equilibrated aqueous phase is converted to the coefficient

  10. A comparative study for the sorption of Cd(II) by soils with different clay contents and mineralogy and the recovery of Cd(II) using rhamnolipid biosurfactant.

    Science.gov (United States)

    Aşçi, Y; Nurbaş, M; Açikel, Y Sağ

    2008-06-15

    Recent research has demonstrated that biosurfactants, especially rhamnolipids, can enhance recovery of soil-bound metals. To propose the success of remediation process of soils by rhamnolipids, both sorption and desorption characteristics of soils having different clay mineralogy should be known exactly. To assess sorption of Cd(II), batch equilibrium experiments were performed using three soils characterized with different proportions of clay minerals from Eskişehir region of Turkey. Soil pH, initial metal concentration and clay mineralogy affected the sorption process. For comparisons between soils, the sorption process was characterized using the Langmuir, Freundlich, Redlich-Peterson, Koble-Corrigan sorption models. The Freundlich model showed the best fit for the Cd(II) sorption data by the soils, while the Langmuir-type models generally failed to describe the sorption data. Soils with higher clay content characterized by having smectite as a dominant component had the greatest sorption capacity and intensity estimated by the KF and n parameters of the Freundlich model. The soil C has the highest sorption efficiency of 83.9%, followed by soils B and A with sorption efficiencies of 76.7% and 57.9%, respectively. After the soils were loaded by different doses of Cd(II), batch washing experiments were used to evaluate the feasibility of using rhamnolipid biosurfactant for the recovery of Cd(II) from the soils. The Cd(II) recovery of the soils were investigated as a function of pH, amount of Cd(II) loaded to the soils, and rhamnolipid concentration. Cd(II) recovery efficiencies from the soils using rhamnolipid biosurfactant decreased in the order of soil A>soil B>soil C. This order was the reverse of the Cd(II) sorption efficiency order on the soils. When 80 mM rhamnolipid was used, the recovery efficiencies of Cd(II) from the soils A, B, and C was found to be 52.9%, 47.7%, 45.5% of the sorbed Cd(II), respectively. Rhamnolipid sorption capacity of the soils in

  11. Har vi brug for hovedregning?

    DEFF Research Database (Denmark)

    Ejersbo, Lisser Rye

    2015-01-01

    Hvor ofte har vi brug for at regne noget i hoved? Har de fleste af os ikke altid et elektronisk hjælpemiddel ved hånden enten som en lille lommeregner eller telefonen? Selvom det umiddelbart kan synes unødvendigt at træne hovedregning, viser det sig, at netop træning af hovedregning støtter...... udvikling af hurtige regnestrategier, hvorfor det faktisk er en god ide at investere tid og energi i at træne netop dette....

  12. Mathematical Modeling of Moisture Sorption Isotherms and Determination of Isosteric Heats of Sorption of Ziziphus Leaves

    Directory of Open Access Journals (Sweden)

    Amel Saad

    2014-01-01

    Full Text Available Desorption and adsorption equilibrium moisture isotherms of Ziziphus spina-christi leaves were determined using the gravimetric-static method at 30, 40, and 50°C for water activity (aw ranging from 0.057 to 0.898. At a given aw, the results show that the moisture content decreases with increasing temperature. A hysteresis effect was observed. The experimental data of sorption were fitted by eight models (GAB, BET, Henderson-Thompson, modified-Chung Pfost, Halsey, Oswin, Peleg, and Adam and Shove. After evaluating the models according to several criteria, the Peleg and Oswin models were found to be the most suitable for describing the sorption curves. The net isosteric heats of desorption and adsorption of Ziziphus spina-christi leaves were calculated by applying the Clausius-Clapeyron equation to the sorption isotherms and an expression for predicting these thermodynamic properties was given.

  13. The Reaction between Iron(II) Iodide and Potassium Dichromate(VI) in Acidified Aqueous Solution

    Science.gov (United States)

    Talbot, Christopher

    2013-01-01

    This "Science note" teaching lesson explores the possible reaction between the ions in a reaction mixture consisting of iron(II) iodide and potassium dichromate(VI) in acidified aqueous solution. The electrode potentials will be used to deduce any spontaneous reactions under standard thermodynamic conditions (298 K, 1 bar (approximately…

  14. Catalytic currents of hydrogen in solutions of W(VI) and mandelic acid

    Energy Technology Data Exchange (ETDEWEB)

    Chikryzova, E.G.; Mashinskaya, S.Ya.

    1986-04-10

    An investigation was made of catalytic polarographic currents of hydrogen in acid dilute solutions of W(VI) with excess of mandelic acid. The nature of the current was studied, and a scheme for the catalytic process is proposed. The reduction of hydrogen ions is catalyzed by the complex (W(OH)HM)/sup 2 +/ adsorbed on the dropping mercury electrode.

  15. Chromium(VI) release from leather and metals can be detected with a diphenylcarbazide spot test

    DEFF Research Database (Denmark)

    Bregnbak, David; Johansen, Jeanne D.; Jellesen, Morten Stendahl

    2015-01-01

    found no false-positive test reactions. Confirmatory testing was performed with X-ray fluorescence (XRF) and spectrophotometrically on extraction fluids. The use of DPC as a colorimetric spot test reagent appears to be a good and valid test method for detecting the release of chromium(VI) ions from...

  16. Implementation of sorption hysteresis in multi-Fickian moisture transport

    DEFF Research Database (Denmark)

    Frandsen, Henrik Lund; Svensson, Staffan

    2007-01-01

    In the cellular structure of wood, bound-water diffusion and water-vapor diffusion interact via sorption in a complex moisture-transportation system. At low relative humidities, moisture transport may be modeled by a Fickian diffusion equation with a good approximation. At higher relative...... represent this behavior. The multi-Fickian model describes the combined transport of bound water and vapor and their interaction through sorption. The bound-water concentration is also influenced by sorption hysteresis. In the worst case, sorption hysteresis may result in deviations of up to 30......-35% in moisture content. Hence, for a precise moisture content computation, sorption hysteresis must be taken into account. The present paper explains the relation between sorption hysteresis and multi-Fickian moisture transport, and clarifies how models for the two phenomena are coupled. To illustrate...

  17. Implementation of sorption hysteresis in multi-Fickian moisture transport

    DEFF Research Database (Denmark)

    Frandsen, Henrik Lund; Svensson, Staffan

    2007-01-01

    In the cellular structure of wood, bound-water diffusion and water-vapor diffusion interact via sorption in a complex moisture-transportation system. At low relative humidity, moisture transport may be modeled by a Fickian diffusion equation to a good approximation. At higher relative humidity...... this behavior. The multi-Fickian model describes the combined transport of bound water and vapor and their interaction through sorption. The bound-water concentration is also influenced by sorption hysteresis. In the worst case, sorption hysteresis may result in deviations of up to 30-35% in moisture content....... Hence, for a precise moisture content computation, sorption hysteresis must be taken into account. The present paper explains the relation between sorption hysteresis and multi-Fickian moisture transport, and clarifies how models for the two phenomena are coupled. To illustrate the effects, a finite...

  18. Radial distribution of ions in pores with a surface charge

    NARCIS (Netherlands)

    van der Stegen, J.H.G.; van der Stegen, J.H.G.; Gortzen, J.; Gortzen, J.; Kuipers, J.A.M.; Hogendoorn, Kees; Versteeg, Geert

    2001-01-01

    A sorption model applicable to calculate the radial equilibrium concentrations of ions in the pores of ion-selective membranes with a pore structure is developed. The model is called the radial uptake model. Because the model is applied to a Nafion sulfonic layer with very small pores and the radial

  19. Adsorption of fluoride ions onto naturally occurring earth materials ...

    African Journals Online (AJOL)

    Batch sorption system using two naturally occurring earth materials (EM) as adsorbents was investigated to remove fluoride ions from aqueous solution. The system variables studied include initial concentration of the sorbate, agitation time, adsorbent dose, pH, co-ions and temperature. The experimental data fitted well to ...

  20. Optimization, equilibrium, kinetic, thermodynamic and desorption studies on the sorption of Cu(II) from an aqueous solution using marine green algae: Halimeda gracilis.

    Science.gov (United States)

    Jayakumar, R; Rajasimman, M; Karthikeyan, C

    2015-11-01

    The aptitude of marine green algae Helimeda gracilis for sorption of Cu(II) ions from an aqueous solution was studied in batch experiments. The effect of relevant parameters such as function of pH, sorbent dosage, agitation speed and contact time was evaluated by using Response surface methodology (RSM). A maximum percentage removal of Cu (II) by Halimeda gracilis occurs at pH-4.49, sorbent dosage-1.98g/L, agitation speed-119.43rpm and contact time-60.21min. Further, the sorbent was characterized by using Fourier Transform Infrared Spectroscopy (FTIR) and Scanning electron microscope (SEM) analysis. Experimental data were analyzed in terms of pseudo-first order, pseudo-second order, intraparticle diffusion, power function and elovich kinetic models. The results showed that the sorption process of Cu(II) ions followed well pseudo-second order kinetics. The sorption data of Cu(II) ions at 308.15K are fitted to Langmuir, Freundlich, Dubinin-Radushkevich (D-R), Temkin, Sips and Toth isotherms. Sorption of Cu(II) onto marine green algae Helimeda gracilis followed the Langmuir and Toth isotherm models (R(2)=0.998 and R(2)=0.999) with the maximum sorption capacity of 38.46 and 38.07mg/g. The calculated thermodynamic parameters such as ΔG°, ΔH° and ΔS° showed that the sorption of Cu(II) ions onto Helimeda gracilis biomass was feasible, spontaneous and endothermic. Desorption study shows that the sorbent could be regenerated using 0.2M HCl solution, with up to 89% recovery. Copyright © 2015 Elsevier Inc. All rights reserved.

  1. Proton magnetic relaxation in aromatic polyamides during water vapor sorption

    Science.gov (United States)

    Smotrina, T. V.; Chulkova, Yu. S.; Karasev, D. V.; Lebedeva, N. P.; Perepelkin, K. E.; Grebennikov, S. F.

    2009-07-01

    The state of the components in the aromatic polyamide-water system was studied by NMR and sorption. A comparative analysis of spin-lattice and spin-spin relaxation in aromatic para-polyamide ( para-aramid) technical fibers Rusar, Kevlar, and Technora was performed depending on the sorption value. The NMR results correlated with the supramolecular structure of polymers and quasi-chemical equation parameters for water vapor sorption.

  2. Hysteresis and Temperature Dependency of Moisture Sorption – New Measurements

    DEFF Research Database (Denmark)

    Rode, Carsten; Hansen, Kurt Kielsgaard

    2011-01-01

    It is well known that sorption characteristics of building materials exhibit hysteresis in the way the equilibrium curves develop between adsorption and desorption, and that the sorption curves are also somewhat temperature dependent. However, these two facts are most often neglected in models...... measurements of hysteresis and temperature dependency of the moisture sorption characteristics of three different porous building materials: aerated concrete, cement paste and spruce. Scanning curves are measured for all three materials where periods with adsorption and desorption interrupt each other...

  3. Sorption of cobalt in zeolites and natural clays of the clinoptilolite and kaolinite type; Sorcion de cobalto en zeolitas y arcillas naturales del tipo clinoptilolita y caolinita

    Energy Technology Data Exchange (ETDEWEB)

    Davila R, J.I.; Solache R, M. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2006-07-01

    In this work the sorption of cobalt of aqueous solutions in two natural zeolites (clinoptilolite) and a clay (kaolinite) of origin in the center-north region of Mexico is evaluated. The effect of the pH and the time of contact in the process of sorption were evaluated. The cobalt retained in the aluminosilicates was determined by neutron activation analysis. The cobalt sorption in the materials in a range of pH from 4 to 7 does not present significant variations. The studies of reaction kinetics show a very fast sorption in the first 5 hours of contact, reaching the equilibrium in approximately 24 hours. The kinetics of sorption of the cobalt ions was represented better by the Ritchie reaction model modified of second order. The experimental data for the zeolites obtained at ambient temperature and varying the concentration were adjusted to the models of Freundlich, Langmuir and Freundlich-Langmuir isotherms and it was observed that the cobalt sorption it behaves according to the Freundlich isotherm model. (Author)

  4. Investigating H 2 Sorption in a Fluorinated Metal–Organic Framework with Small Pores Through Molecular Simulation and Inelastic Neutron Scattering

    KAUST Repository

    Forrest, Katherine A.

    2015-07-07

    © 2015 American Chemical Society. Simulations of H2 sorption were performed in a metal-organic framework (MOF) consisting of Zn2+ ions coordinated to 1,2,4-triazole and tetrafluoroterephthalate ligands (denoted [Zn(trz)(tftph)] in this work). The simulated H2 sorption isotherms reported in this work are consistent with the experimental data for the state points considered. The experimental H2 isosteric heat of adsorption (Qst) values for this MOF are approximately 8.0 kJ mol-1 for the considered loading range, which is in the proximity of those determined from simulation. The experimental inelastic neutron scattering (INS) spectra for H2 in [Zn(trz)(tftph)] reveal at least two peaks that occur at low energies, which corresponds to high barriers to rotation for the respective sites. The most favorable sorption site in the MOF was identified from the simulations as sorption in the vicinity of a metal-coordinated H2O molecule, an exposed fluorine atom, and a carboxylate oxygen atom in a confined region in the framework. Secondary sorption was observed between the fluorine atoms of adjacent tetrafluoroterephthalate ligands. The H2 molecule at the primary sorption site in [Zn(trz)(tftph)] exhibits a rotational barrier that exceeds that for most neutral MOFs with open-metal sites according to an empirical phenomenological model, and this was further validated by calculating the rotational potential energy surface for H2 at this site. (Figure Presented).

  5. Sorption behaviour of nanocrystalline MOR type zeolite for Th(IV) and Eu(III) removal from aqueous waste by batch treatment.

    Science.gov (United States)

    Sharma, Pankaj; Tomar, Radha

    2011-10-01

    The nanocrystalline mordenite (MOR) type zeolite materials with initial chemical composition Na(2)O:Al(2)O(3):10SiO(2):48H(2)O have been synthesized under hydrothermal conditions. MOR1 and MOR2 are spherically shaped nanocrystals, whereas MOR3 and MOR4 have rod-like morphology. This paper reports the sorption characteristics of MOR analogues for Th(IV) and Eu(III) removal from aqueous nuclear waste. Sorption of Th(IV) and Eu(III) on MOR1, MOR2, MOR3 and MOR4 in a single component system with varying initial metal ion concentration, solution pH, contact times, sorbent dose and temperatures has also been investigated. Further, the Langmuir and Freundlich sorption models have been applied to describe equilibrium isotherms at different temperatures. The adsorption capacity increases largely with increasing solution pH and temperature of the system. Specific surface area and pore volume have been investigated by Brunauer-Emmett-Teller (BET) method. The N(2) adsorption isotherm presents a type IV isotherm with narrow hysteresis loop which indicates the presence of mesopores related to inter-particle voids. Thermodynamic results indicate that the sorption follows an endothermic physisorption process. It has been found that these exchangers have good sorption capacity and out of which MOR4 has highest sorption capacity. Thus, nanocrystalline MOR4 is proved to be good sorbent for both Th(IV) and Eu(III). Copyright © 2011 Elsevier Inc. All rights reserved.

  6. Determination of sorption of seventy five pharmaceuticals in sewage sludge

    DEFF Research Database (Denmark)

    Hörsing, Maritha; Ledin, Anna; Grabic, Roman

    2011-01-01

    Sorption of 75 active pharmaceutical ingredients (APIs) to three different types of sludge (primary sludge, secondary sludge with short and long sludge age respectively) were investigated. To obtain the sorption isotherms batch studies with the APIs mixture were performed in four nominal concentr......Sorption of 75 active pharmaceutical ingredients (APIs) to three different types of sludge (primary sludge, secondary sludge with short and long sludge age respectively) were investigated. To obtain the sorption isotherms batch studies with the APIs mixture were performed in four nominal...... was estimated to >80%. 24 APIs were estimated to be present in the liquid phase between 20 and 80%, and 14 APIs were found to have...

  7. Sorption of tebuconazole onto selected soil minerals and humic acids.

    Science.gov (United States)

    Cadková, Eva; Komárek, Michael; Kaliszová, Regina; Koudelková, Věra; Dvořák, Jiří; Vaněk, Aleš

    2012-01-01

    The aim of the present study was to investigate tebuconazole sorption on common soil minerals (birnessite, ferrihydrite, goethite, calcite and illite) and humic acids (representing soil organic matter). Tebuconazole was used (i) in the commercial form Horizon 250 EW and (ii) as an analytical grade pure chemical. In the experiment with the commercially available tebuconazole, a significant pH-dependent sorption onto the oxides was observed (decreasing sorption with increasing pH). The highest sorption was found for ferrihydrite due to its high specific surface area, followed by humic acids, birnessite, goethite and illite. No detectable sorption was found for calcite. The sorption of analytical grade tebuconazole on all selected minerals was significantly lower compared to the commercial product. The sorption was the highest for humic acids, followed by ferrihydrite and illite and almost negligible for goethite and birnessite without any pH dependence. Again, no sorption was observed for calcite. The differences in sorption of the commercially available and analytical grade tebuconazole can be attributed to the additives (e.g., solvents) present in the commercial product. This work proved the importance of soil mineralogy and composition of the commercially available pesticides on the behavior of tebuconazole in soils.

  8. Modification of electrospun polyacrylonitrile nanofibers with EDTA for the removal of Cd and Cr ions from water effluents

    Energy Technology Data Exchange (ETDEWEB)

    Chaúque, Eutilério F.C., E-mail: efchauque@gmail.com [Department of Applied Chemistry, University of Johannesburg, Doornfontein 2028, Johannesburg (South Africa); Dlamini, Langelihle N., E-mail: lndlamini@uj.ac.za [Department of Applied Chemistry, University of Johannesburg, Doornfontein 2028, Johannesburg (South Africa); Adelodun, Adedeji A., E-mail: aadelodun@uj.ac.za [Department of Applied Chemistry, University of Johannesburg, Doornfontein 2028, Johannesburg (South Africa); Greyling, Corinne J., E-mail: GreylingC@cput.ac.za [Technology Station in Clothing and Textiles, Cape Peninsula University of Technology, Symphony Way, Bellville, 7535 (South Africa); Catherine Ngila, J., E-mail: jcngila2002@yahoo.com [Department of Applied Chemistry, University of Johannesburg, Doornfontein 2028, Johannesburg (South Africa)

    2016-04-30

    Graphical abstract: - Highlights: • Polyscrylonitrile (PAN) nanofibers prepared through electrospinning and chemically modified with ethylenediaminetetraacetic acid using ethylenediamine crosslinker. • Fabricated nanofibers have enhanced surface chemistry with insignificant impact on the nanofibrous structure. • Excellent maximum adsorption capacities of 66.24 and 32.68 mg g{sup −1} toward Cr and Cd ions, respectively. • A pre-concentration factor of 19 achieved for removal of Cd and Cr in environmental water samples. - Abstract: Polyacrylonitrile (PAN) nanofibers were obtained by electrospinning technique prior to surface modification with polyethylenediaminetetraacetic acid (EDTA) using ethylenediamine (EDA) as the cross-linker. The modified nanofibers (EDTA-EDA-PAN) were subsequently applied in the wastewater treatment for the removal of Cd(II) and Cr(VI). Textural and chemical characterizations of the nanofibers were carried out by analysis of the specific surface area (Brauner Emmet and Teller (BET)) and thermogravimetric analyses, scanning electron microscopy and Fourier transform infrared spectroscopy. From the adsorption equilibrium studies with Langmuir, Freundlich and Temkin isotherm models, Freundlich was found most suitable for describing the removal mechanism of the target metals as they collect on a heterogeneously functionalized polymer surface. The EDTA-EDA-PAN nanofibers showed effective sorption affinity for both Cd(II) and Cr(VI), achieving maximum adsorption capacities of 32.68 and 66.24 mg g{sup -1}, respectively, at 298 K. In furtherance, the nanofibers were regenerated by simple washing with 2 M HCl solution. Conclusively, the EDTA-EDA-PAN nanofibers were found to be efficient for the removal of Cd(II) and Cr(VI) in water effluents.

  9. Chromium Biosorption from Cr(VI) Aqueous Solutions by Cupressus lusitanica Bark: Kinetics, Equilibrium and Thermodynamic Studies

    OpenAIRE

    Alma Rosa Netzahuatl-Muñoz; María del Carmen Cristiani-Urbina; Eliseo Cristiani-Urbina

    2015-01-01

    The present study investigated the kinetics, equilibrium and thermodynamics of chromium (Cr) ion biosorption from Cr(VI) aqueous solutions by Cupressus lusitanica bark (CLB). CLB total Cr biosorption capacity strongly depended on operating variables such as initial Cr(VI) concentration and contact time: as these variables rose, total Cr biosorption capacity increased significantly. Total Cr biosorption rate also increased with rising solution temperature. The pseudo-second-order model describ...

  10. TREATMENT TESTS FOR EX SITU REMOVAL OF CHROMATE & NITRATE & URANIUM (VI) FROM HANFORD (100-HR-3) GROUNDWATER FINAL REPORT

    Energy Technology Data Exchange (ETDEWEB)

    BECK MA; DUNCAN JB

    1994-01-03

    This report describes batch and ion exchange column laboratory scale studies investigating ex situ methods to remove chromate (chromium [VI]), nitrate (NO{sub 3}{sup -}) and uranium (present as uranium [VI]) from contaminated Hanford site groundwaters. The technologies investigated include: chemical precipitation or coprecipitation to remove chromate and uranium; and anion exchange to remove chromate, uranium and nitrate. The technologies investigated were specified in the 100-HR-3 Groundwater Treatability Test Plan. The method suggested for future study is anion exchange.

  11. Highly selective and efficient removal of arsenic(V), chromium(VI) and selenium(VI) oxyanions by layered double hydroxide intercalated with zwitterionic glycine.

    Science.gov (United States)

    Asiabi, Hamid; Yamini, Yadollah; Shamsayei, Maryam

    2017-10-05

    In this study, a new strategy for highly selective and extremely efficient removal of toxic oxyanions (Cr(VI), Se(VI), and As(V)) from aqueous solutions using zwitterionic glycine intercalated layered double hydroxide (Gly-LDH) was reported. Hence, to investigate the effect of zwitterionic glycine on the adsorption capacity, selectivity factor and adsorption mechanism of LDHs, two NiAl LDHs intercalated with different inter-layer anions, including NO 3 - and glycine, were synthesized. The obtained results show that the adsorption capacity and selectivity factor of oxyanions through ion exchange mechanism in NO 3 -LDH is lower than Gly-LDH. Gly-LDH displayed a selectivity order of Se(VI)exceptionally rapid, showing a 93.5% removal within 30min, 98.0% removal within 40min, and ∼100% removal within 70min. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Synthesis and characterization of polyaniline/zeolite nanocomposite for the removal of chromium(VI from aqueous solution

    Directory of Open Access Journals (Sweden)

    Abdulsalam A. Shyaa

    2015-01-01

    Batch adsorption experiments were used to investigate the effect of various experimental parameters on the equilibrium adsorption of chromium(VI on PANI/zeolite nanocomposite. The adsorption characteristics of the composite toward Cr(VI in dilute aqueous solution were followed spectrophotometrically. The effect of contact time, size of the sorbent and the concentration of Cr(VI in solution on the metal uptake behavior of the composite were studied. It has been observed that the capacity of chromium adsorption on PANI/zeolite increases with initial metal concentration, the metal ion adsorption on surfactant is well represented by the Freundlich isotherm.

  13. Reversible Li-insertion in nanoscaffolds: A promising strategy to alter the hydrogen sorption properties of Li-based complex hydrides

    NARCIS (Netherlands)

    Ngene, Peter; Verkuijlen, Margriet H. W.; Barre, Charlotte; Kentgens, Arno P. M.; de Jongh, Petra E.

    Intercalation and de-intercalation of lithium into graphene layers is a well-established phenomenon in Li-ion battery technology. Here we show how this phenomenon can be exploited to destabilize, and alter the hydrogen sorption behaviour of Li-based metal hydrides (LiBH4 and LiAlH4), thereby

  14. Vi tror ikke noget, vi undersøger det

    DEFF Research Database (Denmark)

    Hansen, Gitte Riis; Winther Johannsen, Inger

    2017-01-01

    I diskussionerne om, hvad der kan betegnes som god viden i forhold til udvikling af pædagogisk ud-vikling og kvalitet, er yderpunkterne kridtet op. Begreber som ”evidensbaseret” og ”datainformeret” synes at udfordre det pædagogiske felts egen forståelse af faglighed og pædagogisk kvalitet. I proj...... tager afsæt i det konkrete projekt og samarbejdet med døgntilbuddene. Vi viser, at arbejdet med datainformeret metode på denne måde ikke er en udradering af pædagogisk faglighed knyttet til fagprofessionel dømmekraft – snarere tværtimod...

  15. Characterization of ‘Aged’ Metolachlor Sorption in Soil Using an Accelerated Solvent Extraction (ASE) Technique

    Science.gov (United States)

    Sorption interactions of pesticides with soil determine pesticide availability for transport and degradation in soil. Thus, knowing and understanding pesticide sorption, particularly in aged soils, is important in determining pesticide fate in soils. Sorption of pesticides is traditionally character...

  16. ADSORPTION OF CHROMIUM (VI FROM AQUEOUS SOLUTIONS BY DIFFERENT ADMIXTURES – A BATCH EQUILIBRIUM TEST STUDY

    Directory of Open Access Journals (Sweden)

    K. SHIVA PRASHANTH KUMAR

    2014-08-01

    Full Text Available Wide variety of inorganic compounds such as nutrients and trace metals, organic chemicals, radioactive contaminants and pathogens are commonly present as contaminants in the groundwater. Migration of contaminants in soil involves important mechanisms such as molecular diffusion, dispersion under physical processes, adsorption, precipitation and oxidation - reduction under chemical processes and biodegradation under biological process. Cr (VI is a major and dangerous contaminant as per the ground water is concerned. There are numerous research work carried out with concentrated efforts by the researchers towards removal of Cr (VI contaminant from aqueous solutions. There are few studies relevant to Cr (VI removal with respect to utilization of low cost admixtures and also soil type. In the present study, different low cost admixtures like rice husk (RH, shredded tyre (ST and fly ash (FA are used to understand the performance in removal of Cr (VI from aqueous solution and also two different soil types are used along with the admixture. The results are discussed in terms of sorption capacity and performance of individual admixture and combination of admixture with soil in removal of contaminant. The fly ash, rice husk and shredded tyre admixtures are used and the results revealed that the shredded tyre showed higher performance in removal of contaminant concentration. Also, the soil which has more fine particle content (size<0.075 mm IS sieve showed reasonable reduction in concentration of contaminant at the lower levels of contaminant initial concentration. The sorption capacity results of Cr (VI contaminant, treated with various admixtures are further validated with the published work of other investigators. The shredded tyre (ST showed more adsorption capacity, i.e., 3.283 mg/g at pH of 4.8. For other admixtures, adsorption capacity value is varying in the range of 0.07 mg/g to 1.7 mg/g. Only in case of activated alumina and modified saw dust

  17. Sorption of Th (IV) to silica as a function of pH, humic/fulvic acid, ionic strength, electrolyte type

    Energy Technology Data Exchange (ETDEWEB)

    Chen Changlun [Institute of Plasma Physics, Chinese Academy of Sciences, P.O. Box 1126, Hefei, 230031, Anhui (China)]. E-mail: clchen@ipp.ac.cn; Wang Xiangke [Institute of Plasma Physics, Chinese Academy of Sciences, P.O. Box 1126, Hefei, 230031, Anhui (China)]. E-mail: xkwang@ipp.ac.cn

    2007-02-15

    The removal behavior of thorium (Th(IV)) has been investigated in multicomponent systems containing silica (SiO{sub 2}) as the model of inorganic particles because of its widespread presence in the earth's crust and soil humic acid (HA)/fulvic acid (FA) by batch experiments. The influence of pH from 2 to 12, ionic strength from 0.02 to 0.2 M KNO{sub 3}, soil HA/FA concentration from 8.3 to 22.5 mg/L, and foreign cations (Li{sup +}, Na{sup +}, K{sup +}) and anions (NO{sub 3} {sup -}, Cl{sup -}) on the sorption of Th(IV) onto SiO{sub 2} was also tested. The sorption isotherms of Th(IV) at approximately constant pH (3.50{+-}0.02) were determined and analyzed regressively with three kinds of sorption isotherm models, i.e., linear, Langmuir, and Freundlich models. The results demonstrated that the sorption of Th(IV) onto SiO{sub 2} increased steeply with increasing pH from 2 to 4. Generally, humic substances (HSs) were shown to enhance Th(IV) sorption at low pH, but to reduce Th(IV) sorption at intermediate and high pH. It was a hypothesis that the significantly positive influence of HA/FA at pH from 2 to 4 on the sorption of Th(IV) onto SiO{sub 2} was attributed to strong surface binding of HA/FA on SiO{sub 2} and subsequently the formation of ternary surface complexes such as {identical_to}MO-O-HA-Th or {identical_to}MO-O-FA-Th. The results also demonstrated that the sorption was strongly dependent on the concentration of HA/FA, and independent of ionic strength and foreign ions under our experimental conditions.

  18. Sorption of Eu(III) and Am(III) on attapulgite. Effect of pH, ionic strength and fulvic acid

    Energy Technology Data Exchange (ETDEWEB)

    Fan, Q.H.; Wu, W.S. [Radiochemistry Lab., School of Nuclear Science and Tech., Lanzhou Univ., GS (China); State Key Lab. of Applied Organic Chemistry, Lanzhou Univ., GS (China); Zhang, M.L.; Zhang, Y.Y.; Ding, K.F.; Yang, Z.Q. [Radiochemistry Lab., School of Nuclear Science and Tech., Lanzhou Univ., GS (China)

    2010-07-01

    Sorption of Eu(III) and Am(III) on attapulgite were studied as a function of pH, ionic strength, the liquid-to-solid ratio (V/m), and Eu(III) and Am(III) concentrations under ambient conditions using batch technique. The sorption of Eu(III) and Am(III) was quickly and {proportional_to} 4 hours were enough to achieve the sorption equilibrium. The K' values were 6.57 x 10{sup 6} g mg{sup -1} h{sup -1} for Eu(III) and 6.67 x 106 g mg{sup -1} h{sup -1} for Am(III), respectively; and q{sub e} values were 4.46 x 10{sup -7} mg/g for Eu(III) and 1.0 x 10{sup -6} mg/g for Am(III), respectively. Sorption of Eu(III) and Am(III) on attapulgite were strongly affected by pH values, and weakly dependent on ionic strength. Sorption of Eu(III) and Am(III) were mainly dominated by surface complexation. although ion exchange also contributed to Eu(III) and Am(III) sorption. In the presence of fulvic acid (FA), the sorption edge of Eu(III) and Am(III) was obviously shifted to lower pH. The results showed that the sorption of Eu(III) and Am(III) to attapulgite was enhanced significantly in the range of pH 0.5 to 6. (orig.)

  19. Sorption capacity of mesoporous metal oxides for the removal of MCPA from polluted waters.

    Science.gov (United States)

    Addorisio, Veria; Esposito, Serena; Sannino, Filomena

    2010-04-28

    A study was performed to assess the sorption capacity of the phenoxy acid herbicide, MCPA, on two mesoporous oxides, Al(2)O(3) and Fe(2)O(3,) by using a batch equilibrium method. Effects of pH, contact time, initial concentration and sorbent dosage on the sorption of the herbicide were investigated. The collected data evidenced the greater sorption efficiency of Al(2)O(3) with respect to Fe(2)O(3). These results can be explained by considering the specific mesoporous structure of Al(2)O(3) together with the greater value of surface area. MCPA is assumed to be bound to Al(2)O(3) and Fe(2)O(3) by a combination of ionic and ion-dipole bonding. Both oxides present as sorbents for a fast and highly efficient removal of MCPA from contaminated waters. For the first time the possible use of mesoporous metal oxides to remove MCPA from contaminated wastewaters identifies these sorbents as suitable filters for the decontamination of point sources.

  20. Measuring the specific caesium sorption capacity of soils, sediments and clay minerals

    Energy Technology Data Exchange (ETDEWEB)

    De Koning, A. [aEnergy Research Centre of the Netherlands (ECN), Westerduinweg 3, P.O. Box 1, 1755 ZG, Petten (Netherlands); Konoplev, A.V. [Institute of Experimental Meteorology, 82 Lenin Avenue, Obninsk, Kaluga Region, 249020 (Russian Federation); Comans, R.N.J. [Wageningen University, Department of Soil Quality, P.O. Box 8005, 6700 EC Wageningen (Netherlands)

    2007-01-15

    Two methods to quantify the specific Cs sorption capacity of soils and sediments, which is generally believed to be associated with the Frayed Edge Sites (FES) of illitic clay minerals, are described in detail and are critically reviewed. The first method is a direct measurement of the FES capacity, while the second quantifies the combined parameter K{sub D}{sup C}s x [K{sup +}] (=K{sub C}(K-->Cs) x [FES]) i.e. the product of the FES capacity and the affinity of these sites for Cs. Both methods use the bulky AgTU-complex to mask non-specific sorption sites for Cs and are applied to a number of different soils and pure minerals. Measurement of the FES capacity of pure illite is straightforward. It is shown that the measured capacity is independent of the saturating ion, but does depend on particle size. This method could not be successfully applied to a peat bog soil with 90% organic matter, because the necessary correction for non-specific Cs sorption by the large pool of organic exchange sites overpasses the capacity of the small FES fraction. Measurement of the combined parameter K{sub D}{sup C}s x [K{sup +}] is shown to be more appropriate in such cases. Application of the FES capacity method to the hydrous aluminosilicate mineral allophane, an important soil constituent of Andisols, shows that the AgTU-complex is unable to block all non-specific sorption sites for Cs on this mineral. The K{sub D}{sup C}s x [K{sup +}] measurements show evidence of a very small number of specific Cs sorption sites on allophane, much smaller than inferred from the FES capacity measurement. The FES capacity of the clay mineral vermiculite is difficult to quantify because the high Cs concentrations that are needed to measure the FES capacity probably cause a collapse of the vermiculite interlayers, thereby creating more high-affinity sites for Cs. The K{sub D}{sup C}s x [K{sup +}] method, in which only trace concentrations of Cs are used, is shown to be more appropriate for soils

  1. Removal of uranyl ions by p-hexasulfonated calyx[6]arene acid

    Energy Technology Data Exchange (ETDEWEB)

    Popescu, Ioana-Carmen [R and D National Institute for Metals and Radioactive Resources–ICPMRR, B-dul Carol I No.70, Sector 2, Bucharest 020917 (Romania); Petru, Filip [“C.D. Nenitescu” Institute of Organic Chemistry, Splaiul Independentei 202B, Sector 6, Bucharest 71141 (Romania); Humelnicu, Ionel [“Al.I. Cuza” University of Iasi, The Faculty of Chemistry, Bd. Carol-I No. 11, Iasi 700506 (Romania); Mateescu, Marina [National R and D Institute for Chemistry and Petrochemistry, Splaiul Independenţei No. 202, Bucharest 060021 (Romania); Militaru, Ecaterina [R and D National Institute for Metals and Radioactive Resources–ICPMRR, B-dul Carol I No.70, Sector 2, Bucharest 020917 (Romania); Humelnicu, Doina, E-mail: doinah@uaic.ro [“Al.I. Cuza” University of Iasi, The Faculty of Chemistry, Bd. Carol-I No. 11, Iasi 700506 (Romania)

    2014-10-15

    Radioactive pollution is a significant threat for the people’s health. Therefore highly effective radioactive decontamination methods are required. Ion exchange, biotechnologies and phytoremediation in constructed wetlands have been used as radioactive decontamination technologies for uranium contaminated soil and water remediation. Recently, beside those classical methods the calix[n]arenic derivatives’ utilization as radioactive decontaminators has jogged attention. The present work aims to present the preliminary research results of uranyl ion sorption studies on the p-hexasulfonated calyx[6]arenic acid. The effect of temperature, contact time, sorbent amount and uranyl concentration variation on sorption efficiency was investigated. Isotherm models revealed that the sorption process fit better Langmuir isotherm.

  2. A comparative in vitro study on fluoride release and water sorption of different flowable esthetic restorative materials

    OpenAIRE

    Harhash, Asmaa Youssif; ElSayad, Iman Ibrahim; Zaghloul, Ahmad G. S.

    2017-01-01

    Objectives: The objective of the study was to evaluate fluoride release and water sorption of three flowable esthetic restorative materials: a giomer, a fluoride-releasing resin composite, and a nonfluoridated resin composite. Materials and Methods: Ten samples from a giomer, a fluoride releasing nano-hybrid, and a nonfluoridated nano-hybrid composite were prepared and immersed in deionized water. Fluoride measurements were done using an ion-specific electrode attached to a microprocessor-bas...

  3. Chromium(VI) release from leather and metals can be detected with a diphenylcarbazide spot test.

    Science.gov (United States)

    Bregnbak, David; Johansen, Jeanne D; Jellesen, Morten S; Zachariae, Claus; Thyssen, Jacob P

    2015-11-01

    Along with chromium, nickel and cobalt are the clinically most important metal allergens. However, unlike for nickel and cobalt, there is no validated colorimetric spot test that detects chromium. Such a test could help both clinicians and their patients with chromium dermatitis to identify culprit exposures. To evaluate the use of diphenylcarbazide (DPC) as a spot test reagent for the identification of chromium(VI) release. A colorimetric chromium(VI) spot test based on DPC was prepared and used on different items from small market surveys. The DPC spot test was able to identify chromium(VI) release at 0.5 ppm without interference from other pure metals, alloys, or leather. A market survey using the test showed no chromium(VI) release from work tools (0/100). However, chromium(VI) release from metal screws (7/60), one earring (1/50), leather shoes (4/100) and leather gloves (6/11) was observed. We found no false-positive test reactions. Confirmatory testing was performed with X-ray fluorescence (XRF) and spectrophotometrically on extraction fluids. The use of DPC as a colorimetric spot test reagent appears to be a good and valid test method for detecting the release of chromium(VI) ions from leather and metal articles. The spot test has