Nickel hydrogen common pressure vessel battery development

Science.gov (United States)

Jones, Kenneth R.; Zagrodnik, Jeffrey P.

1992-01-01

Our present design for a common pressure vessel (CPV) battery, a nickel hydrogen battery system to combine all of the cells into a common pressure vessel, uses an open disk which allows the cell to be set into a shallow cavity; subsequent cells are stacked on each other with the total number based on the battery voltage required. This approach not only eliminates the assembly error threat, but also more readily assures equal contact pressure to the heat fin between each cell, which further assures balanced heat transfer. These heat fin dishes with their appropriate cell stacks are held together with tie bars which in turn are connected to the pressure vessel weld rings at each end of the tube.

The Clementine Nickel Hydrogen Common Pressure Vessel Battery

OpenAIRE

Garner, Christopher

1994-01-01

The Clementine spacecraft was launched in January 1994 to demonstrate advanced lightweight technologies for the Ballistic Missile Defense Organization (BMDO). One of the key technologies was the first use of a multi-cell nickel hydrogen (NiH2) common pressure vessel (CPV) battery. The 5.0 inch diameter, 22 cell, 15.0 ampere-hour NiH2 CPV battery was manufactured by Johnson Controls Battery Group Inc., (JCBGI). Battery test and integration was performed by the Naval Research Laboratory (NRL). ...

Thermal mathematical modeling of a multicell common pressure vessel nickel-hydrogen battery

Science.gov (United States)

Kim, Junbom; Nguyen, T. V.; White, R. E.

1992-01-01

A two-dimensional and time-dependent thermal model of a multicell common pressure vessel (CPV) nickel-hydrogen battery was developed. A finite element solver called PDE/Protran was used to solve this model. The model was used to investigate the effects of various design parameters on the temperature profile within the cell. The results were used to help find a design that will yield an acceptable temperature gradient inside a multicell CPV nickel-hydrogen battery. Steady-state and unsteady-state cases with a constant heat generation rate and a time-dependent heat generation rate were solved.

Single pressure vessel (SPV) nickel-hydrogen battery design

Energy Technology Data Exchange (ETDEWEB)

Coates, D.; Grindstaff, B.; Fox, C. [Eagle-Picher Industries, Inc., Joplin, MO (United States)

1995-07-01

Single pressure vessel (SPV) technology combines an entire multi-cell nickel-hydrogen (NiH{sub 2}) space battery within a single pressure vessel. SPV technology has been developed to improve the performance (volume/mass) of the NiH{sub 2} system at the battery level and ultimately to reduce overall battery cost and increase system reliability. Three distinct SPV technologies are currently under development and in production. Eagle-Picher has license to the COMSAT Laboratories technology, as well as internally developed independent SPV technology. A third technology resulted from the acquisition of Johnson Controls NiH{sub 2} battery assets in June, 1994. SPV batteries are currently being produced in 25 ampere-hour (Ah), 35 Ah and 50 Ah configurations. The battery designs have an overall outside diameter of 10 inches (25.4 centimeters).

Nickel-hydrogen bipolar battery system

Science.gov (United States)

Thaller, L. H.

1982-01-01

Rechargeable nickel-hydrogen systems are described that more closely resemble a fuel cell system than a traditional nickel-cadmium battery pack. This was stimulated by the currently emerging requirements related to large manned and unmanned low Earth orbit applications. The resultant nickel-hydrogen battery system should have a number of features that would lead to improved reliability, reduced costs as well as superior energy density and cycle lives as compared to battery systems constructed from the current state-of-the-art nickel-hydrogen individual pressure vessel cells.

Performance features of 22-cell, 19Ah single pressure vessel nickel hydrogen battery

Energy Technology Data Exchange (ETDEWEB)

Rao, G.M.; Vaidyanathan, H.

1996-02-01

Two 22-cells 19Ah Nickel-Hydrogen (Ni-H2) Single Pressure Vessel (SPV) Qual batteries, one each from EPI/Joplin and EPI/Butler, were designed and procured. The two batteries differ in the cell encapsulation technology, stack preload, and activation procedure. Both the Butler and Joplin batteries met the specified requirements when subjected to qualification testing and completed 2100 and 1300 LEO cycles respectively, with nominal performance. This paper discusses advantages, design features, testing procedures, and results of the two single pressure vessel Ni-H2 batteries.

Performance features of 22-cell, 19Ah single pressure vessel nickel hydrogen battery

Science.gov (United States)

Rao, Gopalakrishna M.; Vaidyanathan, Hari

1996-01-01

Two 22-cells 19Ah Nickel-Hydrogen (Ni-H2) Single Pressure Vessel (SPV) Qual batteries, one each from EPI/Joplin and EPI/Butler, were designed and procured. The two batteries differ in the cell encapsulation technology, stack preload, and activation procedure. Both the Butler and Joplin batteries met the specified requirements when subjected to qualification testing and completed 2100 and 1300 LEO cycles respectively, with nominal performance. This paper discusses advantages, design features, testing procedures, and results of the two single pressure vessel Ni-H2 batteries.

Nickel-hydrogen battery; Nikkeru/suiso batteri

Energy Technology Data Exchange (ETDEWEB)

Kuwajima, S. [National Space Development Agency, Tokyo (Japan)

1996-07-01

In artificial satellites, electric power is supplied from batteries loaded on them, when sun light can not be rayed on the event of equinoxes. Thus, research and development was started as early as 1970s for light and long-life batteries. Nickel-hydrogen batteries have been used on practical satellites since middle of 1980s. Whereas the cathode reaction of this battery is the same as that of a conventional nickel-cadmium battery, the anode reaction is different in that it involves decomposition and formation of water, generating hydrogen and consuming it. Hydrogen is stored in a state of pressurized gas within the battery vessel. The shape of this vessel is of a bomb, whose size for the one with capacity of 35 Ah is 8cm in diameter and 18cm in length. On a satellite, this one is assembled into a set of 16 ones. National Space Development Agency of Japan has been conducting the evaluation test for nickel-hydrogen batteries in a long term range. It was made clear that the life-determinant factor is related to the inner electrode, not to the vessel. Performance data on long-term endurance of materials to be used have been accumulated also in the agency. 2 figs.

Effect of storage and LEO cycling on manufacturing technology IPV nickel-hydrogen cells

Science.gov (United States)

Smithrick, John J.

1987-01-01

Yardney Manufacturing Technology (MANTECH) 50 A-hr space weight individual pressure vessel nickel-hydrogen cells were evaluated. This consisted of investigating: the effect of storage and charge/discharge cycling on cell performance. For the storage test the cells were precharged with hydrogen, by the manufacturer, to a pressure of 14.5 psia. After undergoing activation and acceptance tests, the cells were discharged at C/10 rate (5A) to 0.1 V or less. The terminals were then shorted. The cells were shipped to NASA Lewis Research Center where they were stored at room temperature in the shorted condition for 1 year. After storage, the acceptance tests were repeated at NASA Lewis. A comparison of test results indicate no significant degradation in electrical performance due to 1 year storage. For the cycle life test the regime was a 90 minute low earth orbit at deep depths of discharge (80 and 60 percent). At the 80 percent DOD the three cells failed on the average at cycle 741. Failure for this test was defined to occur when the cell voltage degraded to 1 V prior to completion of the 35 min discharge. The DOD was reduced to 60 percent. The cycle life test was continued.

International Space Station Nickel-Hydrogen Battery On-Orbit Performance

Science.gov (United States)

Dalton, Penni; Cohen, Fred

2002-01-01

International Space Station (ISS) Electric Power System (EPS) utilizes Nickel-Hydrogen (Ni-H2) batteries as part of its power system to store electrical energy. The batteries are charged during insolation and discharged during eclipse. The batteries are designed to operate at a 35 percent depth of discharge (DOD) maximum during normal operation. Thirty-eight individual pressure vessel (IPV) Ni-H2 battery cells are series-connected and packaged in an Orbital Replacement Unit (ORU). Two ORUs are series-connected utilizing a total of 76 cells to form one battery. The ISS is the first application for low earth orbit (LEO) cycling of this quantity of series-connected cells. The P6 (Port) Integrated Equipment Assembly (IEA) containing the initial ISS high-power components was successfully launched on November 30, 2000. The IEA contains 12 Battery Subassembly ORUs (6 batteries) that provide station power during eclipse periods. This paper will discuss the battery performance data after eighteen months of cycling.

Update on International Space Station Nickel-Hydrogen Battery On-Orbit Performance

Science.gov (United States)

Dalton, Penni; Cohen, Fred

2003-01-01

International Space Station (ISS) Electric Power System (EPS) utilizes Nickel-Hydrogen (Ni-H2) batteries as part of its power system to store electrical energy. The batteries are charged during insolation and discharged during eclipse. The batteries are designed to operate at a 35% depth of discharge (DOD) maximum during normal operation. Thirty-eight individual pressure vessel (IPV) Ni-H2 battery cells are series-connected and packaged in an Orbital Replacement Unit (ORU). Two ORUs are series-connected utilizing a total of 76 cells, to form one battery. The ISS is the first application for low earth orbit (LEO) cycling of this quantity of series-connected cells. The P6 (Port) Integrated Equipment Assembly (IEA) containing the initial ISS high-power components was successfully launched on November 30, 2000. The IEA contains 12 Battery Subassembly ORUs (6 batteries) that provide station power during eclipse periods. This paper will discuss the battery performance data after two and a half years of cycling.

Nickel-hydrogen CPV battery update

Science.gov (United States)

Jones, Kenneth R.; Zagrodnik, Jeffrey P.

1993-01-01

The multicell common pressure vessel (CPV) nickel hydrogen battery manufactured by Johnson Controls Battery Group, Inc. has completed full flight qualification, including random vibration at 19.5 g for two minutes in each axis, electrical characterization in a thermal vacuum chamber, and mass-spectroscopy vessel leak detection. A first launch is scheduled for late in 1992 or early 1993 by the Naval Research Laboratory (NRL). Specifics of the launch date are not available at this time due to the classified nature of the program. Release of orbital data for the battery is anticipated following the launch.

International Space Station Nickel-Hydrogen Battery Start-Up and Initial Performance

Science.gov (United States)

Cohen, Fred; Dalton, Penni J.

2001-01-01

International Space Station (ISS) Electric Power System (EPS) utilizes Nickel-Hydrogen (Ni-H2) batteries as part of its power system to store electrical energy. The batteries are charged during insolation and discharged during eclipse. The batteries are designed to operate at a 35% depth of discharge (DOD) maximum during normal operation. Thirty eight individual pressure vessel (IPV) Ni-H2 battery cells are series-connected and packaged in an Orbital Replacement Unit (ORU). Two ORUs are series-connected utilizing a total of 76 cells, to form one battery. The ISS is the first application for low earth orbit (LEO) cycling of this quantity of series-connected cells. The P6 Integrated Equipment Assembly (IEA) containing the initial ISS high-power components was successfully launched on November 30, 2000. The IEA contains 12 Battery Subassembly ORUs (6 batteries) that provide station power during eclipse periods. This paper will describe the battery hardware configuration, operation, and role in providing power to the main power system of the ISS. We will also discuss initial battery start-up and performance data.

Comparison of cell encapsulation technologies for single pressure vessel nickel-hydrogen battery

Energy Technology Data Exchange (ETDEWEB)

Rao, G. [National Aeronautics and Space Administration, Greenbelt, MD (United States). Goddard Space Flight Center; Vaidyanathan, H. [COMSAT Labs., Clarksburg, MD (United States)

1996-12-31

Two single pressure vessel (SPV) batteries containing 22 series-connected nickel-hydrogen (Ni-H{sub 2}) cells of 19-Ah capacity were designed and procured from Eagle-Picher Industries. The two batteries were similar in mechanical design, dimensions, and composition of the active core. However, they differed in cell encapsulation, location and structure of the gas diffusion membrane, and cell activation. Both batteries have been subjected to detailed flight qualification testing at COMSAT Laboratories. The batteries met the requirements in capacity, capacity retention, discharge voltage, impedance, thermal behavior in vacuum, and response to vibration. The batteries are currently being cycle tested in a low earth orbit (LEO) regime using V-T charge control at a depth of discharge of 40% and at 20 C. The battery design, and its characterization, environmental, and LEO cycle test data are presented.

Multikilowatt Bipolar Nickel/Hydrogen Battery

Science.gov (United States)

1986-01-01

High energy densities appear feasible. Nickel/hydrogen battery utilizing bipolar construction in common pressure vessel, addressing needs for multikilowatt storage for low-Earth-orbit applications, designed and 10-cell prototype model tested. Modular-concept-design 35-kW battery projected energy densities of 20 to 24 Wh/b (160 to 190 kj/kg) and 700 to 900 Wh/ft3 (90 to 110 MJ/m3) and incorporated significant improvements over state-of-the-art storage systems.

Multiple cell CPV nickel-hydrogen battery

Science.gov (United States)

Jones, Ken R.; Zagrodnik, Jeffrey P.

1991-01-01

Johnson Controls, Inc. has developed a multiple cell CPV nickel hydrogen battery that offers significant weight, volume, and cost advantages for aerospace applications. The baseline design was successfully demonstrated through the testing of a 26-cell prototype, which completed over 7000 44 percent depth-of-discharge low earth orbit cycles. Prototype designs using both nominal 5 and 10 inch diameter vessels are currently being developed for a variety of customers and applications.

Nickel hydrogen/nickel cadmium battery trade studies

Science.gov (United States)

Stadnick, S. J.

1983-01-01

Nickel Hydrogen cell and battery technology has matured to the point where a real choice exists between Nickel Hydrogen and Nickel Cadmium batteries for each new spacecraft application. During the past few years, a number of spacecraft programs have been evaluated at Hughes with respect to this choice, with the results being split about fifty-fifty. The following paragraphs contain criteria which were used in making the battery selection.

Test results of a 60 volt bipolar nickel-hydrogen battery

Science.gov (United States)

Cataldo, Robert L.; Gonzalez-Sanabria, Olga; Gahn, Randall F.; Manzo, Michelle A.; Gemeiner, Russel P.

1987-01-01

In July 1986, a high-voltage nickel-hydrogen battery was assembled at the NASA Lewis Research Center. This battery incorporated bipolar construction techniques to build a 50-cell stack with approximately 1.0 A-hr capacity (C) and an open-circuit voltage of 65 V. The battery was characterized at both low and high current rates prior to pulsed and nonpulsed discharges. Pulse discharges at 5 and 10 C were performed before placing the battery on over 1400, 40-percent depth-of-discharge, low-earth-orbit cycles. The successful demonstration of a high-voltage bipolar battery in one containment vessel has advanced the technology to where nickel-hydrogen high-voltage systems can be constructed of several modules instead of hundreds of individual cells.

Design of a 1-kWh bipolar nickel hydrogen battery

Science.gov (United States)

Cataldo, R. L.

1984-01-01

The design of a nickel hydrogen battery utilizing bipolar construction in a common pressure vessel is discussed. Design features are as follows: 40 ampere-hour capacity, 1 kWh stored energy as a 24 cell battery, 1.8 kW delivered in a LEO Cycle and maximum pulse power of 18.0 kW.

Investigation of hydrogen evolution activity for the nickel, nickel-molybdenum nickel-graphite composite and nickel-reduced graphene oxide composite coatings

International Nuclear Information System (INIS)

Jinlong, Lv; Tongxiang, Liang; Chen, Wang

2016-01-01

Graphical abstract: - Highlights: • Improved HER efficiency of Ni-Mo coatings was attributed to ‘cauliflower’ like microstructure. • RGO in nickel-RGO composite coating promoted refined grain and facilitated HER. • Synergistic effect between nickel and RGO facilitated HER due to large specific surface of RGO. - Abstract: The nickel, nickel-molybdenum alloy, nickel-graphite and nickel-reduced graphene oxide composite coatings were obtained by the electrodeposition technique from a nickel sulfate bath. Nanocrystalline molybdenum, graphite and reduced graphene oxide in nickel coatings promoted hydrogen evolution reaction in 0.5 M H_2SO_4 solution at room temperature. However, the nickel-reduced graphene oxide composite coating exhibited the highest electrocatalytic activity for the hydrogen evolution reaction in 0.5 M H_2SO_4 solution at room temperature. A large number of gaps between ‘cauliflower’ like grains could decrease effective area for hydrogen evolution reaction in slight amorphous nickel-molybdenum alloy. The synergistic effect between nickel and reduced graphene oxide promoted hydrogen evolution, moreover, refined grain in nickel-reduced graphene oxide composite coating and large specific surface of reduced graphene oxide also facilitated hydrogen evolution reaction.

Investigation of hydrogen evolution activity for the nickel, nickel-molybdenum nickel-graphite composite and nickel-reduced graphene oxide composite coatings

Energy Technology Data Exchange (ETDEWEB)

Jinlong, Lv, E-mail: ljlbuaa@126.com [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China); Tongxiang, Liang; Chen, Wang [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China)

2016-03-15

Graphical abstract: - Highlights: • Improved HER efficiency of Ni-Mo coatings was attributed to ‘cauliflower’ like microstructure. • RGO in nickel-RGO composite coating promoted refined grain and facilitated HER. • Synergistic effect between nickel and RGO facilitated HER due to large specific surface of RGO. - Abstract: The nickel, nickel-molybdenum alloy, nickel-graphite and nickel-reduced graphene oxide composite coatings were obtained by the electrodeposition technique from a nickel sulfate bath. Nanocrystalline molybdenum, graphite and reduced graphene oxide in nickel coatings promoted hydrogen evolution reaction in 0.5 M H{sub 2}SO{sub 4} solution at room temperature. However, the nickel-reduced graphene oxide composite coating exhibited the highest electrocatalytic activity for the hydrogen evolution reaction in 0.5 M H{sub 2}SO{sub 4} solution at room temperature. A large number of gaps between ‘cauliflower’ like grains could decrease effective area for hydrogen evolution reaction in slight amorphous nickel-molybdenum alloy. The synergistic effect between nickel and reduced graphene oxide promoted hydrogen evolution, moreover, refined grain in nickel-reduced graphene oxide composite coating and large specific surface of reduced graphene oxide also facilitated hydrogen evolution reaction.

Development of a Micro-Fiber Nickel Electrode for Nickel-Hydrogen Cell

Science.gov (United States)

Britton, Doris L.

1996-01-01

The development of a high specific energy battery is one of the objectives of the lightweight nickel-hydrogen (NiH2) program at the NASA Lewis Research Center. The approach has been to improve the nickel electrode by continuing combined in-house and contract efforts to develop a more efficient and lighter weight electrode for the nickel-hydrogen fuel cell. Small fiber diameter nickel plaques are used as conductive supports for the nickel hydroxide active material. These plaques are commercial products and have an advantage of increased surface area available for the deposition of active materials. Initial tests include activation and capacity measurements at different discharge levels followed by half-cell cycle testing at 80 percent depth-of-discharge in a low Earth orbit regime. The electrodes that pass the initial tests are life cycle tested in a boiler plate nickel-hydrogen cell before flightweight designs are built and tested.

Nickel hydrogen battery cell storage matrix test

Science.gov (United States)

Wheeler, James R.; Dodson, Gary W.

1993-01-01

Test were conducted to evaluate post storage performance of nickel hydrogen cells with various design variables, the most significant being nickel precharge versus hydrogen precharge. Test procedures and results are presented in outline and graphic form.

Progress in the Development of Lightweight Nickel Electrode for Nickel-Hydrogen Cell

Science.gov (United States)

Britton, Doris L.

1999-01-01

Development of a high specific energy battery is one of the objectives of the lightweight nickel-hydrogen (Ni-H2) program at the NASA Glenn Research Center. The approach has been to improve the nickel electrode by continuing combined in-house and contract efforts to develop a lighter weight electrode for the nickel-hydrogen cell. Small fiber diameter nickel plaques are used as conductive supports for the nickel hydroxide active material. These plaques are commercial products and have an advantage of increased surface area available for the deposition of active material. Initial tests include activation and capacity measurements at five different discharge levels, C/2, 1.0 C, 1.37 C, 2.0 C, and 2.74 C. The electrodes are life cycle tested using a half-cell configuration at 40 and 80% depths-of-discharge (DOD) in a low-Earth-orbit regime. The electrodes that pass the initial tests are life cycle-tested in a boiler plate nickel-hydrogen cell before flight weight design are built and tested.

Nickel hydrogen bipolar battery electrode design

Science.gov (United States)

Puglisi, V. J.; Russell, P.; Verrier, D.; Hall, A.

1985-01-01

The preferred approach of the NASA development effort in nickel hydrogen battery design utilizes a bipolar plate stacking arrangement to obtain the required voltage-capacity configuration. In a bipolar stack, component designs must take into account not only the typical design considerations such as voltage, capacity and gas management, but also conductivity to the bipolar (i.e., intercell) plate. The nickel and hydrogen electrode development specifically relevant to bipolar cell operation is discussed. Nickel oxide electrodes, having variable type grids and in thicknesses up to .085 inch are being fabricated and characterized to provide a data base. A selection will be made based upon a system level tradeoff. Negative (hydrpogen) electrodes are being screened to select a high performance electrode which can function as a bipolar electrode. Present nickel hydrogen negative electrodes are not capable of conducting current through their cross-section. An electrode was tested which exhibits low charge and discharge polarization voltages and at the same time is conductive. Test data is presented.

Reactivity of hydrogen contained in Raney nickel for ethylene hydrogenation studied by means of a tritium tracer

International Nuclear Information System (INIS)

Miyatani, Daisaku; Takeuchi, Toyosaburo.

1979-01-01

Reactivity of hydrogen contained in Raney nickel with ethylene was studied by using a tritium tracer. Hydrogen in Raney nickel was previously labeled with tritium and distinguished from hydrogen introduced during the hydrogenation reaction. The reactivity of the contained hydrogen was determined by measurement of the radioactivity of ethane produced in the hydrogenation. Ethylene reacted with hydrogen in Raney nickel for no supply of hydrogen during the hydrogenation. However, when ethylene was hydrogenated by both hydrogen in Raney nickel and introduced hydrogen, over 99% of the ethylene reacted with the introduced hydrogen and hardly reacted with the contained hydrogen. (author)

Investigation of nickel hydrogen battery technology for the RADARSAT spacecraft

Science.gov (United States)

Mccoy, D. A.; Lackner, J. L.

1986-01-01

The low Earth orbit (LEO) operations of the RADARSAT spacecraft require high performance batteries to provide energy to the payload and platform during eclipse period. Nickel Hydrogen cells are currently competing with the more traditional Nickel Cadmium cells for high performance spacecraft applications at geostationary Earth orbit (GEO) and Leo. Nickel Hydrogen cells appear better suited for high power applications where high currents and high Depths of Discharge are required. Although a number of GEO missions have flown with Nickel Hydrogen batteries, it is not readily apparent that the LEO version of the Nickel Hydrogen cell is able to withstand the extended cycle lifetime (5 years) of the RADARSAT mission. The problems associated with Nickel Hydrogen cells are discussed in the contex of RADARSAT mission and a test program designed to characterize cell performance is presented.

Hydrogen permeation inhibition by zinc-nickel alloy plating on steel XC68

International Nuclear Information System (INIS)

El Hajjami, A.; Gigandet, M.P.; De Petris-Wery, M.; Catonne, J.C.; Duprat, J.J.; Thiery, L.; Raulin, F.; Starck, B.; Remy, P.

2008-01-01

The inhibition of hydrogen permeation and barrier effect by zinc-nickel plating was investigated using the Devanathan-Stachurski permeation technique. The hydrogen permeation and hydrogen diffusion for the zinc-nickel (12-15%) plating on steel XC68 is compared with zinc and nickel. Hydrogen permeation and hydrogen diffusion were followed as functions of time at current density applied (cathodic side) and potential permanent (anodic side). The hydrogen permeation inhibition for zinc-nickel is intermediate to that of nickel and zinc. This inhibition was due to nickel-rich layer effects at the Zn-Ni alloy/substrate interface, is shown by GDOES. Zinc-nickel plating inhibited the hydrogen diffusion greater as compared to zinc. This diffusion resistance was due to the barrier effect caused by the nickel which is present at the interface and transformed the hydrogen atomic to Ni 2 H compound, as shown by GIXRD.

Hydrogen permeation inhibition by zinc-nickel alloy plating on steel XC68

Energy Technology Data Exchange (ETDEWEB)

El Hajjami, A. [Institut UTINAM, UMR CNRS 6213, Sonochimie et Reactivite des Surfaces, Universite de Franche-Comte, 16 route de Gray, 25030 Besancon Cedex (France); Coventya S.A.S., 51 rue Pierre, 92588 Clichy Cedex (France); Gigandet, M.P. [Institut UTINAM, UMR CNRS 6213, Sonochimie et Reactivite des Surfaces, Universite de Franche-Comte, 16 route de Gray, 25030 Besancon Cedex (France)], E-mail: marie-pierre.gigandet@univ-fcomte.fr; De Petris-Wery, M. [Institut Universitaire de Technologie d' Orsay, Universite Paris XI, Plateau de Moulon, 91400 Orsay (France); Catonne, J.C. [Professeur Honoraire du Conservatoire national des arts et metiers (CNAM), Paris (France); Duprat, J.J.; Thiery, L.; Raulin, F. [Coventya S.A.S., 51 rue Pierre, 92588 Clichy Cedex (France); Starck, B.; Remy, P. [Lisi Automotive, 28 faubourg de Belfort, BP 19, 90101 Delle Cedex (France)

2008-12-30

The inhibition of hydrogen permeation and barrier effect by zinc-nickel plating was investigated using the Devanathan-Stachurski permeation technique. The hydrogen permeation and hydrogen diffusion for the zinc-nickel (12-15%) plating on steel XC68 is compared with zinc and nickel. Hydrogen permeation and hydrogen diffusion were followed as functions of time at current density applied (cathodic side) and potential permanent (anodic side). The hydrogen permeation inhibition for zinc-nickel is intermediate to that of nickel and zinc. This inhibition was due to nickel-rich layer effects at the Zn-Ni alloy/substrate interface, is shown by GDOES. Zinc-nickel plating inhibited the hydrogen diffusion greater as compared to zinc. This diffusion resistance was due to the barrier effect caused by the nickel which is present at the interface and transformed the hydrogen atomic to Ni{sub 2}H compound, as shown by GIXRD.

Nickel brittling by hydrogen. Temperature effect

International Nuclear Information System (INIS)

Lapitz, P.A; Fernandez, S; Alvarez, M.G

2006-01-01

The results of a study on the effect of different variables on the susceptibility to brittling by hydrogen and the velocity of propagation of fissures in nickel wire (99.7% purity) are described. The hydrogen load was carried out by cathodic polarization in H 2 SO 4 0.5m solution. The susceptibility to brittling by hydrogen was determined with traction tests at slow deformation speed and constant cathodic potential, and the later observation of the fracture surface by scanning electron microscopy. The variables studied were: applied cathodic overpower, speed of initial deformation and temperature. The results showed that the speed of fissure propagation in the nickel by brittleness from hydrogen is a function of the applied potential and the speed of deformation used. Without tension, the hydrogen load by cathodic polarization at room temperature leads to the formation of cavities similar to those observed when the hydrogenation is performed in the presence of gaseous hydrogen at high pressure and temperature (CW)

Hydrogen storage in insulated pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Aceves, S.M.; Garcia-Villazana, O. [Lawrence Livermore National Lab., CA (United States)

1998-08-01

Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen (LH{sub 2}) or ambient-temperature compressed hydrogen (CH{sub 2}). Insulated pressure vessels offer the advantages of liquid hydrogen tanks (low weight and volume), with reduced disadvantages (lower energy requirement for hydrogen liquefaction and reduced evaporative losses). This paper shows an evaluation of the applicability of the insulated pressure vessels for light-duty vehicles. The paper shows an evaluation of evaporative losses and insulation requirements and a description of the current analysis and experimental plans for testing insulated pressure vessels. The results show significant advantages to the use of insulated pressure vessels for light-duty vehicles.

Hydrogen-water deuterium exchange over metal oxide promoted nickel catalysts

Energy Technology Data Exchange (ETDEWEB)

Sagert, N H; Shaw-Wood, P E; Pouteau, R M.L. [Atomic Energy of Canada Ltd., Pinawa, Manitoba. Whiteshell Nuclear Research Establishment

1975-11-01

Specific rates have been measured for hydrogen-water deuterium isotope exchange over unsupported nickel promoted with about 20% of various metal oxides. The oxides used were Cr/sub 2/O/sub 3/, MoO/sub 2/, MnO, WO/sub 2/-WO/sub 3/, and UO/sub 2/. Nickel surface areas, which are required to measure the specific rates, were determined by hydrogen chemisorption. Specific rates were measured as a function of temperature in the range 353 to 573 K and as a function of the partial pressure of hydrogen and water over a 10-fold range of partial pressure. The molybdenum and tungsten oxides gave the highest specific rates, and manganese and uranium oxides the lowest. Chromium oxide was intermediate, although it gave the highest rate per gram of catalyst. The orders with respect to hydrogen and water over molybdenum oxide and tungsten oxide promoted nickel were consistent with a mechanism in which nickel oxide is formed from the reaction of water with the catalyst, and then is reduced by hydrogen. Over manganese and uranium oxide promoted catalysts, these orders are consistent with a mechanism in which adsorbed water exchanges with chemisorbed hydrogen atoms on the nickel surface. Chromium oxide is intermediate. It was noted that those oxides which favored the nickel oxide route had electronic work functions closest to those of metallic nickel and nickel oxide.

Hydrogen absorption kinetics of niobium with an ion-plated nickel overlayer

International Nuclear Information System (INIS)

Nakamura, K.

1981-01-01

The hydrogen absorption rate for nickel-ion-plated niobium was measured as a function of hydrogen pressure and temperature. The observed absorption curves of c(mean)/csub(e) against time (c(mean) and csub(e) are the mean and equilibrium hydrogen concentrations respectively) exhibited a marked hydrogen pressure dependence below 628 K but this was less marked above 723 K. The results were analysed on the basis of the proposed model that the rate-determining step is the hydrogen permeation through the nickel overlayer and that the permeation is driven by the hydrogen activity difference between the two interfaces, namely the H 2 -Ni and Ni-Nb interfaces. The marked pressure dependence can be attributed to the fact that the hydrogen activity coefficient in nickel is constant and that in niobium it varies markedly with concentration, i.e. with hydrogen pressure and temperature. It was also found that the change in the nickel overlayer structure caused by the dilatation of bulk niobium during hydrogen absorption enhances the hydrogen absorption rates. The temperature dependence of the hydrogen absorption rate is also discussed in comparison with that for tantalum with a vacuum-deposited nickel overlayer. (Auth.)

Development of nickel-hydrogen battery for electric vehicle; Denki jidoshayo nickel-suiso denchi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Research and development of battery, a main part of electric vehicle, have been promoted. Various batteries, such as lead battery, nickel-cadmium battery, nickel-hydrogen battery, lithium ion battery and so on, have been investigated for electric vehicles. Among these, nickel-hydrogen battery is superior to the others from the points of energy density, lifetime, low-temperature properties, and safety. It is one of the most prospective batteries for electric vehicle. Research and development of the nickel-hydrogen battery with higher energy density and longer lifetime have been promoted for the practical application by Tohoku Electric Power Co., Inc. This article shows main performance of the developed nickel-hydrogen battery for electric vehicle. The nominal voltage is 12 V, the rated capacity is 125 Ah, the outside dimension is L302{times}W170{times}H245 mm, the weight is 25.5 kg, the energy density is 60 Wh/kg, the output density is 180 W/kg, and the available environment temperature is between -20 and 60 {degree}C. 1 fig., 1 tab.

Nickel Hydrogen Battery Expert System

Science.gov (United States)

Johnson, Yvette B.; Mccall, Kurt E.

1992-01-01

The Nickel Cadmium Battery Expert System-2, or 'NICBES-2', which was used by the NASA HST six-battery testbed, was subsequently converted into the Nickel Hydrogen Battery Expert System, or 'NICHES'. Accounts are presently given of this conversion process and future uses being contemplated for NICHES. NICHES will calculate orbital summary data at the end of each orbit, and store these files for trend analyses and rules-generation.

First principles nickel-cadmium and nickel hydrogen spacecraft battery models

Energy Technology Data Exchange (ETDEWEB)

Timmerman, P.; Ratnakumar, B.V.; Distefano, S.

1996-02-01

The principles of Nickel-Cadmium and Nickel-Hydrogen spacecraft battery models are discussed. The Ni-Cd battery model includes two phase positive electrode and its predictions are very close to actual data. But the Ni-H2 battery model predictions (without the two phase positive electrode) are unacceptable even though the model is operational. Both models run on UNIX and Macintosh computers.

Nickel-hydrogen battery with oxygen and electrolyte management features

Science.gov (United States)

Sindorf, John F.

1991-10-22

A nickel-hydrogen battery or cell having one or more pressure vessels containing hydrogen gas and a plurality of cell-modules therein. Each cell-module includes a configuration of cooperatively associated oxygen and electrolyte mangement and component alignment features. A cell-module having electrolyte includes a negative electrode, a positive electrode adapted to facilitate oxygen diffusion, a separator disposed between the positive and negative electrodes for separating them and holding electrolyte for ionic conductivity, an absorber engaging the surface of the positive electrode facing away from the separator for providing electrolyte to the positive electrode, and a pair of surface-channeled diffusion screens for enclosing the positive and negative electrodes, absorber, and separator and for maintaining proper alignment of these components. The screens, formed in the shape of a pocket by intermittently sealing the edges together along as many as three sides, permit hydrogen gas to diffuse therethrough to the negative electrodes, and prevent the edges of the separator from swelling. Electrolyte is contained in the cell-module, absorbhed by the electrodes, the separator and the absorber.

Results of a technical analysis of the Hubble Space Telescope nickel-cadmium and nickel-hydrogen batteries

Science.gov (United States)

Manzo, Michelle A.

1991-01-01

The Hubble Space Telescope (HST) Program Office requested the expertise of the NASA Aerospace Flight Battery Systems Steering Committee (NAFBSSC) in the conduct of an independent assessment of the HST's battery system to assist in their decision of whether to fly nickel-cadmium or nickel-hydrogen batteries on the telescope. In response, a subcommittee to the NAFBSSC was organized with membership comprised of experts with background in the nickel-cadmium/nickel-hydrogen secondary battery/power systems areas. The work and recommendations of that subcommittee are presented.

Life cycle evaluation of spaceflight qualified nickel-hydrogen batteries

Energy Technology Data Exchange (ETDEWEB)

Coates, D.K.; Brill, J.N. [Eagle-Picher Industries, Inc., Joplin, MO (United States). Advanced Systems Operation

1995-12-31

Life cycle test results are summarized from more than 300 spaceflight qualified nickel-hydrogen (NiH{sub 2}) battery cells currently on life test. Cells ranging in size from 4 ampere-hours (Ah) to 120 Ah are being tested under a variety of conditions to support current NiH{sub 2} battery applications. Results to date include 55,600 accelerated LEO cycles at 30% DOD; 102,840 accelerated LEO cycles at 15% DOD; 44,900 cycles under a real-time LEO profile; 44,100 cycles in real-time LEO; 30 accelerated GEO eclipse seasons and 7 real-time GEO eclipse seasons, both at 75% DOD maximum. Alternative separator materials have completed more than 40,000 charge/discharge cycles in accelerated LEO testing and advanced design electrocatalytic hydrogen electrodes have completed more than 16,000 cycles in real-time LEO testing. Common pressure vessel cell designs have completed 18,000 cycles in real-time LEO testing at 45% DOD.

New developments in nickel-hydrogen cell and battery design for commercial applications

Energy Technology Data Exchange (ETDEWEB)

Caldwell, D.B.; Fox, C.L.; Miller, L.E. [Eagle-Picher Industries, Inc., Joplin, MO (United States)

1997-12-31

Nickel-hydrogen (NiH{sub 2}) battery systems were first developed for space applications more than 20 years ago. Currently, they are being manufactured for commercial, terrestrial applications. The battery is ideal for commercial terrestrial energy storage applications because it offers a better potential cycle life than any other battery system and is maintenance free. A selection of low-cost components, electrodes, cell designs and battery designs are being tested to determine their feasibility for commercial applications. The dependent pressure vessel (DPV) design, developed by Eagle-Picher Industries, is the newest step in the continued development and evolution of the NiH{sub 2} system. The unique feature of the DPV cell design is the prismatic electrode stack which is more efficient than the cylindrical electrode stack. The electrode stack is the electrochemically active part of the cell. It contains nickel and hydrogen electrodes interspersed with an absorbent separator. DPV cells of two sizes, 40 and 60 Ah cells, have been developed. The DPV cell offers high specific energy at a reduced cost. The advanced DPV design also offers an efficient mechanical, electrical and thermal configuration and a reduced parts count. The design promotes compact, minimum volume packaging and weight efficiency. 8 refs., 7 figs.

Nickel-hydrogen battery and hydrogen storage alloy electrode; Nikkeru suiso denchi oyobi suiso kyuzo gokin denkyoku

Energy Technology Data Exchange (ETDEWEB)

Ono, T. [Furukawa Electric Co. Ltd., Tokyo (Japan); Furukawa, J. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

1996-03-22

Hermetically sealed nickel-hydrogen battery has such problem that the inner pressure of the battery elevates when it is overcharged since the oxygen gas evolves from the positive electrode. This invention relates to the hermetically sealed nickel-hydrogen battery consisting of positive electrode composed mainly of nickel hydroxide and negative electrode composed mainly of hydrogen storage alloy. According to the invention, the negative electrode contains organic sulfur compound having carbon-sulfur bond. As a result, the elevation of battery inner pressure due to the hydrogen gas evolution, the decrease in discharge capacity due to the repetition of charge and discharge, and the lowering of voltage after charging can be suppressed. The adequate content of the organic sulfur compound is 0.05 - 1 part in weight to 100 part in weight of hydrogen storage alloy. As for the organic sulfur compound, n-butylthiol, ethylthioethane, phenyldithiobenzene, trimethylsulfonium bromide, thiobenzophenone, 2,4-dinitrobenzenesulfenyl chloride, and ethylene sulphidic acid are employed. 2 figs., 1 tab.

Air Force standards for nickel hydrogen battery

Science.gov (United States)

Hwang, Warren; Milden, Martin

1994-01-01

The topics discussed are presented in viewgraph form and include Air Force nickel hydrogen standardization goals, philosophy, project outline, cell level standardization, battery level standardization, and schedule.

Development of nickel hydrogen battery expert system

Science.gov (United States)

Shiva, Sajjan G.

1990-01-01

The Hubble Telescope Battery Testbed employs the nickel-cadmium battery expert system (NICBES-2) which supports the evaluation of performances of Hubble Telescope spacecraft batteries and provides alarm diagnosis and action advice. NICBES-2 also provides a reasoning system along with a battery domain knowledge base to achieve this battery health management function. An effort to modify NICBES-2 to accommodate nickel-hydrogen battery environment in testbed is described.

A microfabricated nickel-hydrogen battery using thick film printing techniques

Science.gov (United States)

Tam, Waiping G.; Wainright, Jesse S.

To utilize the distinctive cycle life and safety characteristics of the nickel-hydrogen chemistry while eliminating the high pressure limitations of conventional nickel-hydrogen cells, a microfabricated nickel-hydrogen battery using a low-pressure metal hydride for hydrogen storage is being developed for powering micro-electromechanical systems (MEMS) devices and for biomedical applications where the battery would be implanted within the body. Thick film printing techniques which are simple and low cost were used to fabricate this battery. Inks were developed for each of the different battery components, including the electrodes, current collectors and separator. SEM images on these printed components showed the desired characteristics for each. Positive electrode cycling tests were performed on the printed positive electrodes while cyclic voltammetry was used to characterize the printed negative electrodes. Consistent charge and discharge performance was observed during positive electrode cycling. Full cells with printed positive and negative assemblies were assembled and tested.

A microfabricated nickel-hydrogen battery using thick film printing techniques

Energy Technology Data Exchange (ETDEWEB)

Tam, Waiping G.; Wainright, Jesse S. [Department of Chemical Engineering, Case Western Reserve University, Cleveland, OH 44106 (United States)

2007-02-25

To utilize the distinctive cycle life and safety characteristics of the nickel-hydrogen chemistry while eliminating the high pressure limitations of conventional nickel-hydrogen cells, a microfabricated nickel-hydrogen battery using a low-pressure metal hydride for hydrogen storage is being developed for powering micro-electromechanical systems (MEMS) devices and for biomedical applications where the battery would be implanted within the body. Thick film printing techniques which are simple and low cost were used to fabricate this battery. Inks were developed for each of the different battery components, including the electrodes, current collectors and separator. SEM images on these printed components showed the desired characteristics for each. Positive electrode cycling tests were performed on the printed positive electrodes while cyclic voltammetry was used to characterize the printed negative electrodes. Consistent charge and discharge performance was observed during positive electrode cycling. Full cells with printed positive and negative assemblies were assembled and tested. (author)

Retention of hydrogen isotopes and helium in nickel

Energy Technology Data Exchange (ETDEWEB)

Okada, Mitsumasa; Sato, Rikiya; Yamaguchi, Kenji; Yamawaki, Michio [Tokyo Univ., Tokai, Ibaraki (Japan). Nuclear Engineering Research Lab.

1996-10-01

In the present study, a thin foil of nickel was irradiated by H{sub 2}{sup +}, D{sub 2}{sup +} and He{sup +} to a fluence of 1.2-6.0x10{sup 20}/m{sup 2} using the TBTS (Tritium Beam Test System) apparatus. The thermal desorption spectroscopy (TDS) technique was employed to evaluate the total amount of retained hydrogen isotope and helium atoms in nickel. In the spectra, two peaks appeared at 440-585K and 720-735K for helium. Hydrogen isotopes irradiation after helium preirradiation were found to enhance the helium release and to decrease the peak temperatures. Helium irradiation after hydrogen isotopes preirradiation were found to enhance the helium release, but the peak temperature showed little difference from that without preirradiation. (author)

Process for forming a nickel foil with controlled and predetermined permeability to hydrogen

Science.gov (United States)

Engelhaupt, Darell E.

1981-09-22

The present invention provides a novel process for forming a nickel foil having a controlled and predetermined hydrogen permeability. This process includes the steps of passing a nickel plating bath through a suitable cation exchange resin to provide a purified nickel plating bath free of copper and gold cations, immersing a nickel anode and a suitable cathode in the purified nickel plating bath containing a selected concentration of an organic sulfonic acid such as a napthalene-trisulfonic acid, electrodepositing a nickel layer having the thickness of a foil onto the cathode, and separating the nickel layer from the cathode to provide a nickel foil. The anode is a readily-corrodible nickel anode. The present invention also provides a novel nickel foil having a greater hydrogen permeability than palladium at room temperature.

Process for forming a nickel foil with controlled and predetermined permeability to hydrogen

International Nuclear Information System (INIS)

Engelhaupt, D. E.

1981-01-01

The present invention provides a novel process for forming a nickel foil having a controlled and predetermined hydrogen permeability. This process includes the steps of passing a nickel plating bath through a suitable cation exchange resin to provide a purified nickel plating bath free of copper and gold cations, immersing a nickel anode and a suitable cathode in the purified nickel plating bath containing a selected concentration of an organic sulfonic acid such as a napthalene-trisulfonic acid, electrodepositing a nickel layer having the thickness of a foil onto the cathode, and separating the nickel layer from the cathode to provide a nickel foil. The anode is a readilycorrodible nickel anode. The present invention also provides a novel nickel foil having a greater hydrogen permeability than palladium at room temperature

Templated synthesis of nickel nanoparticles: Toward heterostructured nanocomposites for efficient hydrogen storage

Energy Technology Data Exchange (ETDEWEB)

Nelson, Nicholas Cole [Iowa State Univ., Ames, IA (United States)

2013-01-01

The world is currently facing an energy and environmental crisis for which new technologies are needed. Development of cost-competitive materials for catalysis and hydrogen storage on-board motor vehicles is crucial to lead subsequent generations into a more sustainable and energy independent future. This thesis presents work toward the scalable synthesis of bimetallic heterostructures that can enable hydrogen to compete with carbonaceous fuels by meeting the necessary gravimetric and volumetric energy densities and by enhancing hydrogen sorption/desorption kinetics near ambient temperatures and pressures. Utilizing the well-known phenomenon of hydrogen spillover, these bimetallic heterostructures could work by lowering the activation energy for hydrogenation and dehydrogenation of metals. Herein, we report a novel method for the scalable synthesis of silica templated zero-valent nickel particles (Ni$\\subset$ SiO₂) that hold promise for the synthesis of nickel nanorods for use in bimetallic heterostructures for hydrogen storage. Our synthesis proceeds by chemical reduction of a nickel-hydrazine complex with sodium borohydride followed by calcination under hydrogen gas to yield silica encapsulated nickel particles. Transmission electron microscopy and powder X-ray diffraction were used to characterize the general morphology of the resultant nanocapsules as well as the crystalline phases of the incorporated Ni⁰ nanocrystals. The structures display strong magnetic behavior at room temperature and preliminary data suggests nickel particle size can be controlled by varying the amount of nickel precursor used in the synthesis. Calcination under different environments and TEM analysis provides evidence for an atomic migration mechanism of particle formation. Ni$\\subset$SiO₂ nanocapsules were used as seeds to induce heterogeneous nucleation and subsequent growth within the nanocapsule via electroless nickel plating. Nickel nanoparticle

Charge retention test experiences on Hubble Space Telescope nickel-hydrogen battery cells

Science.gov (United States)

Nawrocki, Dave E.; Driscoll, J. R.; Armantrout, J. D.; Baker, R. C.; Wajsgras, H.

1993-01-01

The Hubble Space Telescope (HST) nickel-hydrogen battery module was designed by Lockheed Missile & Space Co (LMSC) and manufactured by Eagle-Picher Ind. (EPI) for the Marshall Space Flight Center (MSFC) as an Orbital Replacement Unit (ORU) for the nickel-cadmium batteries originally selected for this low earth orbit mission. The design features of the HST nickel hydrogen battery are described and the results of an extended charge retention test are summarized.

Hypervelocity Impact Testing of Nickel Hydrogen Battery Cells

Science.gov (United States)

Frate, David T.; Nahra, Henry K.

1996-01-01

Nickel-Hydrogen (Ni/H2) battery cells have been used on several satellites and are planned for use on the International Space Station. In January 1992, the NASA Lewis Research Center (LeRC) conducted hypervelocity impact testing on Ni/H2 cells to characterize their failure modes. The cell's outer construction was a 24 mil-thick Inconel 718 pressure vessel. A sheet of 1.27 cm thick honeycomb was placed in front of the battery cells during testing to simulate the on-orbit box enclosure. Testing was conducted at the NASA White Sands Test Facility (WSTF). The hypervelocity gun used was a 7.6 mm (0.30 caliber) two-stage light gas gun. Test were performed at speeds of 3, 6, and 7 km/sec using aluminum 2017 spherical particles of either 4.8 or 6.4 mm diameter as the projectile. The battery cells were electrically charged to about 75 percent of capacity, then back-filled with hydrogen gas to 900 psi simulating the full charge condition. High speed film at 10,000 frames/sec was taken of the impacts. Impacts in the dome area (top) and the electrode area (middle) of the battery cells were investigated. Five tests on battery cells were performed. The results revealed that in all of the test conditions investigated, the battery cells simply vented their hydrogen gas and some electrolyte, but did not burst or generate any large debris fragments.

Metal hydrides for hydrogen storage in nickel hydrogen batteries

International Nuclear Information System (INIS)

Bittner, H.F.; Badcock, C.C.; Quinzio, M.V.

1984-01-01

Metal hydride hydrogen storage in nickel hydrogen (Ni/H 2 ) batteries has been shown to increase battery energy density and improve battery heat management capabilities. However the properties of metal hydrides in a Ni/H 2 battery environment, which contains water vapor and oxygen in addition to the hydrogen, have not been well characterized. This work evaluates the use of hydrides in Ni/H 2 batteries by fundamental characterization of metal hydride properties in a Ni/H 2 cell environment. Hydrogen sorption properties of various hydrides have been measured in a Ni/H 2 cell environment. Results of detailed thermodynamic and kinetic studies of hydrogen sorption in LaNi 5 in a Ni/H 2 cell environment are presented. Long-term cycling studies indicate that degradation of the hydride can be minimized by cycling between certain pressure limits. A model describing the mechanism of hydride degradation is presented

Nickel-Hydrogen Battery Reconditioning

Science.gov (United States)

Levine, Erik L.

1997-01-01

Reconditioning has traditionally been used as a means of maintaining the performance of normal cells and batteries. This paper describes methods and results in which reconditioning was used to improve the performance of nickel-hydrogen batteries. The following method are discussed: (1) SS/L reconditioning implementation; (2) Superbird reconditioning - pressure/capacity growth; (3) INTELSAT 7/7A reconditioning - cell voltage plateaus and life testing; and (4) N-Star reconditioning - cell voltage plateaus (capacity fading and recovery).

75 Ah and 10 boilerplate nickel-hydrogen battery designs and test results

Science.gov (United States)

Daman, M. E.; Manzo, Michelle A.; Chang, R.; Cruz, E.

1992-01-01

The results of initial characterization testing of 75 Ah actively cooled bipolar battery designs and 10 boilerplate nickel-hydrogen battery designs are presented. The results demonstrate the extended cycle life capability of the Ah batteries and the high capacity utilizations at various discharge rates of the nickel-hydrogen batteries.

Vacuum vessel of thermonuclear device and manufacturing method thereof

International Nuclear Information System (INIS)

Kurita, Genichi; Nagashima, Keisuke; Uchida, Takaho; Shibui, Masanao; Ebisawa, Katsuyuki; Nakagawa, Satoshi.

1997-01-01

The present invention provides a vacuum vessel of a thermonuclear device using, as a material of a plasma vacuum vessel, a material to be less activated and having excellent strength as well as a manufacturing method thereof. Namely, the vacuum vessel is made of titanium or a titanium alloy. In addition, a liner layer comprising a manganese alloy, nickel alloy, nickel-chromium alloy or aluminum or aluminum alloy is formed. With such a constitution, the wall substrate made of titanium or a titanium alloy can be isolated by the liner from hydrogen or plasmas. As a result, occlusion of hydrogen to titanium or the titanium alloy can be prevented thereby enabling to prevent degradation of the material of the wall substrate of the vacuum vessel. In addition, since the liner layer has relatively high electric resistance, a torus circumferential resistance value required for plasma ignition can be ensured by using it together with the vessel wall made of titanium alloy. (I.S.)

A submerged ceramic membrane reactor for the p-nitrophenol hydrogenation over nano-sized nickel catalysts.

Science.gov (United States)

Chen, R Z; Sun, H L; Xing, W H; Jin, W Q; Xu, N P

2009-02-01

The catalytic hydrogenation of p-nitrophenol to p-aminophenol over nano-sized nickel catalysts was carried out in a submerged ceramic membrane reactor. It has been demonstrated that the submerged ceramic membrane reactor is more suitable for the p-nitrophenol hydrogenation over nano-sized nickel catalysts compared with the side-stream ceramic membrane reactor, and the membrane module configuration has a great influence on the reaction rate of p-nitrophenol hydrogenation and the membrane treating capacity. The deactivation of nano-sized nickel is mainly caused by the adsorption of impurity on the surface of nickel and the increase of oxidation degree of nickel.

Partial filling of d-band of nickel on hydrogen diffusion

International Nuclear Information System (INIS)

Kapoor, N.; Nigam, A.N.

1987-01-01

It is seen that low-temperature annealing of nickel wires forbids the complete filling in of the d-band of nickel when the latter is subjected to cathodic-hydrogen diffusion. At a certain low-temperature range irreversible changes occur in the orientation of the surface planes of nickel which persist even if the temperature is raised to the room temperature

Fabrication of Nickel Nanotube Using Anodic Oxidation and Electrochemical Deposition Technologies and Its Hydrogen Storage Property

Directory of Open Access Journals (Sweden)

Yan Lv

2016-01-01

Full Text Available Electrochemical deposition technique was utilized to fabricate nickel nanotubes with the assistance of AAO templates. The topography and element component of the nickel nanotubes were characterized by TEM and EDS. Furthermore, the nickel nanotube was made into microelectrode and its electrochemical hydrogen storage property was studied using cyclic voltammetry. The results showed that the diameter of nickel nanotubes fabricated was around 20–100 mm, and the length of the nanotube could reach micron grade. The nickel nanotubes had hydrogen storage property, and the hydrogen storage performance was higher than that of nickel powder.

IPv4-protokollasta siirtyminen IPv6-protokollaan

OpenAIRE

Ylituomaala, Jaakko

2011-01-01

Tässä työssä tutkitaan IPv6-osoiteavaruutta, sekä IPv6-protokollan yhteensopivuutta IPv4-protokollan kanssa. Työssä käydään läpi myös yleisimmät IPv4-yhteensopivat IPv6-reititysmenetelmät. Tutkimuksessa tutustutaan pääpiirteittäin IPv4-osoiteluokkiin, itse osoitteisiin ja IPv4-headeriin. IPv4 osoiteryhmiä on viisi, jotka ovat A, B, C, D ja E. Lisäksi luodaan katsaus IPv4-headerin eri osioihin ja tutustutaan niiden käyttötarkoituksiin. Työssä käydään läpi myös osittain NAT-toiminto. Tu...

Fractography of hydrogen-embrittled iron-chromium-nickel alloys

International Nuclear Information System (INIS)

Caskey, G.R. Jr.

1980-01-01

Tensile specimens of iron-chromium-nickel base alloys were broken in either a hydrogen environment or in air following thermal charging with hydrogen. Fracture surfaces were examined by scanning electron microscopy. Fracture morphology of hydrogen-embrittled specimens was characterized by: changed dimple size, twin-boundary parting, transgranular cleavage, and intergranular separation. The nature and extent of the fracture mode changes induced by hydrogen varied systematically with alloy composition and test temperature. Initial microstructure developed during deformation processing and heat treating had a secondary influence on fracture mode

Determination of the gaseous hydrogen ductile-brittle transition in copper-nickel alloys

Science.gov (United States)

Parr, R. A.; Johnston, M. H.; Davis, J. H.; Oh, T. K.

1985-01-01

A series of copper-nickel alloys were fabricated, notched tensile specimens machined for each alloy, and the specimens tested in 34.5 MPa hydrogen and in air. A notched tensile ratio was determined for each alloy and the hydrogen environment embrittlement (HEE) determined for the alloys of 47.7 weight percent nickel to 73.5 weight percent nickel. Stacking fault probability and stacking fault energies were determined for each alloy using the x ray diffraction line shift and line profiles technique. Hydrogen environment embrittlement was determined to be influenced by stacking fault energies; however, the correlation is believed to be indirect and only partially responsible for the HEE behavior of these alloys.

Deployment IPv6 over IPv4 network infrastructure

OpenAIRE

Hoang, Tien Dung

2015-01-01

The purpose of this thesis is doing the research about IPv6, concentrate in how to deploy an IPv6 network based on IPv4 network without making any interruption to IPv4 network. This thesis is made for Financing and Promoting Technology Corporation (FPT) in Vietnam. This thesis is completed in two main parts. The theoretical part is making research about IPv4 and IPv6 to have the point of view about IPv4 and IPv6 basically, and from those one, seeing the advantages of IPv6 comparing wit...

Implementasi Migrasi Ipv4 Ke Ipv6

OpenAIRE

Syafrizal, Melwin; Qamar, Syamsul; Aji, Damawan Bayu

2013-01-01

IPv4 yang digunakan di jaringan publik (internet) sudah habis, sehingga kebutuhan koneksi internet baru tidak dapat dilayani. Layanan baru, konten baru, domain name baru, server baru, router baru tidak dapat koneksi ke internet, kecuali menggunakan IPv6. Migrasi IPv4 ke IPv6 bukan hal yang mudah, pengetahuan baru tentang IPv6 perlu dipelajari, kondisi-kondisi yang akan dialami akibat Perubahan IP, mekanisme transisi, atau mekanisme routing perlu dipahami. Cara-cara konfigurasi IPv6 pada berba...

Intermetallic nickel silicide nanocatalyst-A non-noble metal-based general hydrogenation catalyst.

Science.gov (United States)

Ryabchuk, Pavel; Agostini, Giovanni; Pohl, Marga-Martina; Lund, Henrik; Agapova, Anastasiya; Junge, Henrik; Junge, Kathrin; Beller, Matthias

2018-06-01

Hydrogenation reactions are essential processes in the chemical industry, giving access to a variety of valuable compounds including fine chemicals, agrochemicals, and pharmachemicals. On an industrial scale, hydrogenations are typically performed with precious metal catalysts or with base metal catalysts, such as Raney nickel, which requires special handling due to its pyrophoric nature. We report a stable and highly active intermetallic nickel silicide catalyst that can be used for hydrogenations of a wide range of unsaturated compounds. The catalyst is prepared via a straightforward procedure using SiO 2 as the silicon atom source. The process involves thermal reduction of Si-O bonds in the presence of Ni nanoparticles at temperatures below 1000°C. The presence of silicon as a secondary component in the nickel metal lattice plays the key role in its properties and is of crucial importance for improved catalytic activity. This novel catalyst allows for efficient reduction of nitroarenes, carbonyls, nitriles, N-containing heterocycles, and unsaturated carbon-carbon bonds. Moreover, the reported catalyst can be used for oxidation reactions in the presence of molecular oxygen and is capable of promoting acceptorless dehydrogenation of unsaturated N-containing heterocycles, opening avenues for H 2 storage in organic compounds. The generality of the nickel silicide catalyst is demonstrated in the hydrogenation of over a hundred of structurally diverse unsaturated compounds. The wide application scope and high catalytic activity of this novel catalyst make it a nice alternative to known general hydrogenation catalysts, such as Raney nickel and noble metal-based catalysts.

The Earth Observing System (EOS) nickel-hydrogen battery

Science.gov (United States)

Bennett, Charles W.

1992-01-01

Information is given in viewgraph form on the Earth Observing System (EOS) nickel hydrogen battery. Information is given on the life evaluation test, cell characteristics, acceptance and characterization tests, and the battery system description.

Transition from IPv4 to IPv6

DEFF Research Database (Denmark)

Henten, Anders; Tadayoni, Reza

The paper examines the transition from IPv4 to IPv6. More specifically, the aim of the paper is to present information on the status of the transition process and on the drivers and barriers concerning this transition. This includes an update on the availability of IPv4 addresses and on how far t...... the adoption of IPv6 has come. It also includes a discussion on what but also who the drivers and barriers are, including an examination of the implications of implementing transfer markets for IPv4 addresses.......The paper examines the transition from IPv4 to IPv6. More specifically, the aim of the paper is to present information on the status of the transition process and on the drivers and barriers concerning this transition. This includes an update on the availability of IPv4 addresses and on how far...

PWG4 perspective on ex-vessel hydrogen sources

International Nuclear Information System (INIS)

2000-07-01

The purpose of this perspective document is to identify the potential ex-vessel hydrogen sources and to address the question whether, considered the uncertainties associated to these sources, further investigations are required. The statement is established with reference to the needs for safety evaluation of nuclear reactors under severe accident conditions. It is recognised that the views could be different if one looks at these issues from another standpoint. Since the TMI-2 accident in 1979, there had been a large interest in the nuclear reactor safety community for studying the behaviour of hydrogen in case of a severe accident. As a result, different 'state of the art' reports were produced. Examples of these documents are NUREG/CR-1561 and EUR 14307. In particular, they identified potential hydrogen sources during accidents, including ex-vessel sources. Various ex-vessel hydrogen sources, covering a variety of physical and chemical processes, were identified. Although their precise quantification and relative importance is to be established on a case by case basis with respect to the specific reactor design of interest, general trends can be formulated. The sources to be considered are the followings: - radiolysis of water; - corrosion reactions, - reaction of urania with steam and water; - core-concrete interaction; - debris-atmosphere interaction. These sources are discussed successively. The PWG4 (CSNI's Principal Working Group on the Confinement of Accidental Radioactive Releases) perspective on Ex-vessel Hydrogen Sources can be summarised in the following statements: 1. The issue of hydrogen sources must be considered as a whole and cannot be separated into in-vessel and ex-vessel issues. For significant sources that may not be accommodated by mitigation means associated to DBA, the uncertainty is largely dominated by the unknown extent of Zr oxidation during the in-vessel phase. 2. PWG4 notes that hydrogen production during corium quenching by water is

Hydrogen pressure dependence of the fracture mode transition in nickel

International Nuclear Information System (INIS)

Jones, R.H.; Baer, D.R.; Bruemmer, S.M.; Thomas, M.T.

1983-01-01

A relationship between fracture mode, grain boundary composition, and hydrogen pressure has been determined for nickel straining electrode samples tested at cathodic potentials. This relationship can be expressed as C /SUB S/ α P /SUP -n/ /SUB H2/ where C /SUB S/ is the critical grain boundary sulfur concentration corresponding to 50% transgranular and 50% intergranular fracture and P /SUB H2/ is the hydrogen pressure. The value of n was found to be between 0.34 and 0.9. This expression was derived by relating C /SUB S/ to the hydrogen overpotential with the Nernst equation. At a cathodic test potential of -0.3 V (SCE), C /SUB S/ was equal to 0.20 monolayers of sulfur and at higher cathodic potentials or higher hydrogen pressures, C /SUB S/ decreased such that at -0.72 V (SCE) C /SUB S/ was equal to 0.045 monolayers of sulfur. The inverse hydrogen pressure dependence observed with cathodic hydrogen is similar to that for the hydrogen permeation rate or a critical hydrogen concentration derived by Gerberich et al. for gaseous hydrogen. This similarity between gaseous and cathodic hydrogen suggests that grain boundary impurities contribute to the hydrogen embrittlement process without altering the embrittlement process although this result does not indicate whether decohesion or plasticity dependent processes are responsible for the combined sulfur-hydrogen effect on the intergranular fracture of nickel

Advances in nickel hydrogen technology at Yardney Battery Division

Science.gov (United States)

Bentley, J. G.; Hall, A. M.

1987-01-01

The current major activites in nickel hydrogen technology being addressed at Yardney Battery Division are outlined. Five basic topics are covered: an update on life cycle testing of ManTech 50 AH NiH2 cells in the LEO regime; an overview of the Air Force/industry briefing; nickel electrode process upgrading; 4.5 inch cell development; and bipolar NiH2 battery development.

Analysis and Design of Cryogenic Pressure Vessels for Automotive Hydrogen Storage

Science.gov (United States)

Espinosa-Loza, Francisco Javier

Cryogenic pressure vessels maximize hydrogen storage density by combining the high pressure (350-700 bar) typical of today's composite pressure vessels with the cryogenic temperature (as low as 25 K) typical of low pressure liquid hydrogen vessels. Cryogenic pressure vessels comprise a high-pressure inner vessel made of carbon fiber-coated metal (similar to those used for storage of compressed gas), a vacuum space filled with numerous sheets of highly reflective metalized plastic (for high performance thermal insulation), and a metallic outer jacket. High density of hydrogen storage is key to practical hydrogen-fueled transportation by enabling (1) long-range (500+ km) transportation with high capacity vessels that fit within available spaces in the vehicle, and (2) reduced cost per kilogram of hydrogen stored through reduced need for expensive structural material (carbon fiber composite) necessary to make the vessel. Low temperature of storage also leads to reduced expansion energy (by an order of magnitude or more vs. ambient temperature compressed gas storage), potentially providing important safety advantages. All this is accomplished while simultaneously avoiding fuel venting typical of cryogenic vessels for all practical use scenarios. This dissertation describes the work necessary for developing and demonstrating successive generations of cryogenic pressure vessels demonstrated at Lawrence Livermore National Laboratory. The work included (1) conceptual design, (2) detailed system design (3) structural analysis of cryogenic pressure vessels, (4) thermal analysis of heat transfer through cryogenic supports and vacuum multilayer insulation, and (5) experimental demonstration. Aside from succeeding in demonstrating a hydrogen storage approach that has established all the world records for hydrogen storage on vehicles (longest driving range, maximum hydrogen storage density, and maximum containment of cryogenic hydrogen without venting), the work also

Cost reductions in nickel-hydrogen battery

Science.gov (United States)

Beauchamp, Richard L.; Sindorf, Jack F.

1987-01-01

Significant progress was made toward the development of a commercially marketable hydrogen nickel oxide battery. The costs projected for this battery are remarkably low when one considers where the learning curve is for commercialization of this system. Further developmental efforts on this project are warranted as the H2/NiO battery is already cost competitive with other battery systems.

Impact of shuttle environment on prelaunch handling of nickel-hydrogen batteries

Science.gov (United States)

Green, R. S.

1986-01-01

Deployment of the American Satellite Company 1 spacecraft for the Space Shuttle Discovery in August 1985 set a new milestone in nickel-hydrogen battery technology. This communications satellite is equipped with two 35 Ah nickel-hydrogen batteries and it is the first such satellite launched into orbit via the Space Shuttle. The prelaunch activities, combined with the environmental constraints onboard the Shuttle, led to the development of a new battery handling procedure. An outline of the prelaunch activities, with particular attention to battery charging, is presented.

Hydrogen pressure dependence of the fracture mode transition in nickel

International Nuclear Information System (INIS)

Jones, R.H.; Baer, D.R.; Bruemmer, S.M.; Thomas, M.T.

1983-01-01

A relationship between fracture mode, grain boundary composition, and hydrogen pressure has been determined for nickel straining electrode samples tested at cathodic potentials. This relationship can be expressed as C /SUB s/ α P /SUP -n/ /SUB H2/ where C /SUB s/ is the critical grain boundary sulfur concentration corresponding to 50 pct transgranular and 50 pct intergranular fracture and P /SUB H2/ is the hydrogen pressure. The value of n was found to be between 0.34 and 0.9. This expression was derived by relating C /SUB s/ to th hydrogen overpotential with the Nernst equation. At a cathodic test potential of -0.3 V (SCE). C /SUB s/ was equal to 0.20 monolayers of sulfur and at higher cathodic potentials or higher hydrogen pressures, C /SUB s/ decreased such that at -0.72 V (SCE) C /SUB s/ was equal to 0.045 monolayers of sulfur. The inverse hydrogen pressure dependence observed with cathodic hydrogen is similar to that for the hydrogen permeation rate or a critical hydrogen concentration derived by Gerberich et al. for gaseous hydrogen. This similarity between gaseous and cathodic hydrogen suggests that grain boundary impurities contribute to the hydrogen embrittlement process without altering the embrittlement process although this result does not indicate whether decohesion or plasticity dependent processes are responsible for the combined sulfur-hydrogen effect on the intergranular fracture of nickel

Interaction of atomic hydrogen with ethylene adsorbed on nickel films

International Nuclear Information System (INIS)

Korchak, V.N.; Tret'yakov, I.I.; Kislyuk, M.U.

1976-01-01

The reactivity of ethylene adsorbed on the pure films of nickel at various temperatures was studied with respect to hydrogen atoms generated in the gaseous phase. The experiments were conducted in a glass vacuum apparatus enabling one to obtain the highest vacuum up to 2x20 -10 torr. The catalyst, nickel films, was produced by their deposition onto the walls of the glass reactor at a pressure of the residual gas of 10 -9 torr and a temperature of the walls of 25 deg C. Gas purity was analyzed by the mass spectrometric method. The ethylene adsorbed at the temperatures below 173 deg K reacted readily with the hydrogen atoms to yield ethane. The process ran without practically any activation energy involved and was limited by the attachment of the first hydrogen atom to the ethylene molecule. The efficiency of this interaction was 0.02 of the number of the hydrogen atoms collisions against the surface occupied by the ethylene. The adsorption of the ethylene at room and higher temperatures was accompanied by its disproportioning with the release of the hydrogen into the gaseous phase and a serious destruction of the ethylene molecules adsorbed to produce hydrogen residues interacting with neither molecular nor atomic hydrogen [ru

Wustite-based photoelectrodes with lithium, hydrogen, sodium, magnesium, manganese, zinc and nickel additives

Science.gov (United States)

Carter, Emily Ann; Toroker, Maytal Caspary

2017-08-15

A photoelectrode, photovoltaic device and photoelectrochemical cell and methods of making are disclosed. The photoelectrode includes an electrode at least partially formed of FeO combined with at least one of lithium, hydrogen, sodium, magnesium, manganese, zinc, and nickel. The electrode may be doped with at least one of lithium, hydrogen, and sodium. The electrode may be alloyed with at least one of magnesium, manganese, zinc, and nickel.

Packet traffic features of IPv6 and IPv4 protocol traffic

OpenAIRE

ÇİFLİKLİ, Cebrail; GEZER, Ali; ÖZŞAHİN, Abdullah Tuncay

2012-01-01

Nowadays, the IPv6 protocol is in a transition phase in operational networks. The ratio of its traffic volume is increasing day by day. The many provided facilities for IPv6 connection increasethe total IPv6 traffic load. IPv6-over-IPv4 tunnels, pilot programsto provide IPv6 connections, IPv6/IPv4 dual stack operating systems,and free IPv6 tunnel brokers cause the IPv6 protocol to expand quickly. For efficient resource utilization, the characteristics of network traffic should be determ...

Hydrogenation properties and microstructure of Ti-Mn-based alloys for hybrid hydrogen storage vessel

International Nuclear Information System (INIS)

Shibuya, Masachika; Nakamura, Jin; Akiba, Etsuo

2008-01-01

Ti-Mn-based AB 2 -type alloys which are suitable for a hybrid hydrogen storage vessel have been synthesized and evaluated hydrogenation properties. As the third element V was added to Ti-Mn binary alloys. All the alloys synthesized in this work mainly consist of the C14 Laves and BCC phase. In the case of Ti0.5V0.5Mn alloy, the amounts of hydrogen absorption was 1.8 wt.% at 243 K under the atmosphere of 7 MPa H 2 , and the hydrogen desorption pressure was in the range of 0.2-0.4 MPa at 243 K. The hydrogen capacity of this alloy did not saturate under 7 MPa H 2 and seems to increase with hydrogen pressure up to 35 MPa that is estimated working pressure of the hybrid hydrogen storage vessel

Evaluation of nickel-hydrogen battery for space application

Science.gov (United States)

Billard, J. M.; Dupont, D.

1983-01-01

Results of electrical space qualification tests of nickel-hydrogen battery type HR 23S are presented. The results obtained for the nickel-cadmium battery type VO 23S are similar except that the voltage level and the charge conservation characteristics vary significantly. The electrical and thermal characteristics permit predictions of the following optimal applications: charge coefficient in the order of 1.3 to 1.4 at 20C; charge current density higher than C/10 at 20C; discharge current density from C/10 to C/3 at 20C; maximum discharge temperature: OC; storage temperature: -20C.

Hydrogen Production by Steam Reforming of Natural Gas Over Vanadium-Nickel-Alumina Catalysts.

Science.gov (United States)

Yoo, Jaekyeong; Park, Seungwon; Song, Ji Hwan; Song, In Kyu

2018-09-01

A series of vanadium-nickel-alumina (xVNA) catalysts were prepared by a single-step sol-gel method with a variation of vanadium content (x, wt%) for use in the hydrogen production by steam reforming of natural gas. The effect of vanadium content on the physicochemical properties and catalytic activities of xVNA catalysts in the steam reforming of natural gas was investigated. It was found that natural gas conversion and hydrogen yield showed volcano-shaped trends with respect to vanadium content. It was also revealed that natural gas conversion and hydrogen yield increased with decreasing nickel crystallite size.

IPv4 and IPv6 protocol compatibility options analysis

Directory of Open Access Journals (Sweden)

Regina Misevičienė

2013-09-01

Full Text Available The popularity of the internet has led to a very rapid growth of IPv4 (Internet Protocol v4 users. This caused a shortage of IP addresses, so it was created a new version – IPv6 (Internet Protocol v6. Currently, there are two versions of IP for IPv4 and IPv6. Due to the large differences in addressing the protocols IPv4 and IPv6 are incompatible. It is therefore necessary to find ways to move from IPv4 to IPv6. To facilitate the transition from one version to another are developed various mechanisms and strategies. Comparative analysis is done for dual stack, 6to4 tunnel and NAT64 mechanisms in this work. It has helped to reveal the shortcomings of these mechanisms and their application in selection of realization decisions.

Problems of the internet transition from protocol IPv4 to IPv6

OpenAIRE

Potrebuješ , Nejc

2013-01-01

Internet currently coexist of older IPv4 networks, new IPv6 network and networks that supports both IPv6 and IPv4 stack. IPv4 and IPv6 networks are unfortunately incompatible. To enable communication between these two networks several mechanisms were developed. These mechanisms are so called »IPv4/v6 transition mechanisms«. In this thesis first there are IPv4 and IPv6 protocols presented, disadvantages of an IPv4 protocol and advantages of an IPv6 protocol. Further there are some transitio...

Hydrogenation of surface carbon on alumina-supported nickel

Energy Technology Data Exchange (ETDEWEB)

Mccarthy, J.G.; Wise, H.

1979-05-01

The methanation of carbon deposited by CO or ethylene decomposition on Girdler G-65 catalyst (25Vertical Bar3< nickel, 8Vertical Bar3< alkali, mostly CaO, 4Vertical Bar3< C as graphite, on alumina) was studied by temperature-programed desorption and temperature-programed surface reaction. Four types of carbon were identified: ..cap alpha..-carbon consisted of isolated carbon atoms bonded to nickel and reacting with hydrogen at 470/sup 0/ +/- 20/sup 0/K; ..gamma..-carbon was probably a bulk carbide, most likely Ni/sub 3/C, which had a reaction peak at 550/sup 0/K; ..beta..-carbon consisted of amorphous, polymerized carbon, which had a reaction peak at 680/sup 0/K; and an unreactive crystalline graphite-like species. The ..cap alpha..-form was thermally unstable and transformed into the ..beta..-form above 600/sup 0/K. Both ..cap alpha..- and ..beta..-forms slowly converted to inert graphite above 600/sup 0/K. The evidence suggested that synthesis gas methanation proceeds by dissociative adsorption of CO as the rate-determining step which forms a very reactive carbon adatom state (..cap alpha..') which converts to the ..cap alpha..-state in the absence of hydrogen and to methane in the presence of hydrogen.

IPv6-protokolla

OpenAIRE

Hautanen, Jukka-Pekka

2012-01-01

Tämän työn tarkoituksena on tutkia IPv6-protokollaa ja IPv6-protokollan yhteensopivuutta IPv4-protokollan kanssa. Työn alussa tarkastellaan IPv6-protokollan historiaa ja tämän hetkistä levinneisyyttä. Työssä paneudutaan tarkemmin IPv6-protokollan pääpiirteisiin: IPv6-protokollan osoitetyypit ja niiden esitystavat, aliverkotus, IPv6-protokollan uudistetun otsikon rakenne ja uudet lisäotsikot. Edellä mainittuja pääpiirteitä verrataan tarvittaessa IPv4-protokollaan, jotta nähdään parannukset...

Life Modeling for Nickel-Hydrogen Batteries in Geosynchronous Satellite Operation

National Research Council Canada - National Science Library

Zimmerman, A. H; Ang, V. J

2005-01-01

.... The model has been used to predict how properly designed and operated nickel-hydrogen battery lifetimes should depend on the operating environments and charge control methods typically used in GEO operation...

Evaluation of nickel and copper catalysts in biogas reforming for hydrogen production in SOFC

Energy Technology Data Exchange (ETDEWEB)

Silva, Leonardo Alves; Martins, Andre Rosa; Rangel, Maria do Carmo, E-mail: mcarmov@ufba.br [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Grupo de Estudos em Cinetica e Catalise; Ballarini, Adriana; Maina, Silvia [Instituto de Investigaciones en Catalisis Y Petroquimica Ing. Jose Miguel Parera (INCAPE), Santa Fe (Argentina)

2017-01-15

The solid oxide fuel cells (SOFC) enable the efficient generation of clean energy, fitting the current requirements of the growing demand for electricity and for the environment preservation. When powered with biogas (from digesters of municipal wastes), the SOFCs also contribute to reduce the environmental impact of these wastes. The most suitable route to produce hydrogen inside SOFC from biogas is through dry reforming but the catalyst is easily deactivated by coke, because of the high amounts of carbon in the stream. A promising way to overcome this drawback is by adding a second metal to nickel-based catalysts. Aiming to obtain active, selective and stable catalysts for biogas dry reforming, solids based on nickel (15%) and copper (5%) supported on aluminum and magnesium oxide were studied in this work. Samples were prepared by impregnating the support with nickel and copper nitrate, followed by calcination at 500, 600 and 800 deg C. It was noted that all solids were made of nickel oxide, nickel aluminate and magnesium aluminate but no copper compound was found. The specific surface areas did not changed with calcination temperature but the nickel oxide average particles size increased. The solids reducibility decreased with increasing temperature. All catalysts were active in methane dry reforming, leading to similar conversions but different selectivities to hydrogen and different activities in water gas shift reaction (WGSR). This behavior was assigned to different interactions between nickel and copper, at different calcination temperatures. All catalysts were active in WGSR, decreasing the hydrogen to carbon monoxide molar ratio and producing water. The catalyst calcined at 500 deg C was the most promising one, leading to the highest hydrogen yield, besides the advantage of being produced at the lowest calcination temperature, requiring less energy in its preparation. (author)

Evaluation of nickel and copper catalysts in biogas reforming for hydrogen production in SOFC

International Nuclear Information System (INIS)

Silva, Leonardo Alves; Martins, Andre Rosa; Rangel, Maria do Carmo

2017-01-01

The solid oxide fuel cells (SOFC) enable the efficient generation of clean energy, fitting the current requirements of the growing demand for electricity and for the environment preservation. When powered with biogas (from digesters of municipal wastes), the SOFCs also contribute to reduce the environmental impact of these wastes. The most suitable route to produce hydrogen inside SOFC from biogas is through dry reforming but the catalyst is easily deactivated by coke, because of the high amounts of carbon in the stream. A promising way to overcome this drawback is by adding a second metal to nickel-based catalysts. Aiming to obtain active, selective and stable catalysts for biogas dry reforming, solids based on nickel (15%) and copper (5%) supported on aluminum and magnesium oxide were studied in this work. Samples were prepared by impregnating the support with nickel and copper nitrate, followed by calcination at 500, 600 and 800 deg C. It was noted that all solids were made of nickel oxide, nickel aluminate and magnesium aluminate but no copper compound was found. The specific surface areas did not changed with calcination temperature but the nickel oxide average particles size increased. The solids reducibility decreased with increasing temperature. All catalysts were active in methane dry reforming, leading to similar conversions but different selectivities to hydrogen and different activities in water gas shift reaction (WGSR). This behavior was assigned to different interactions between nickel and copper, at different calcination temperatures. All catalysts were active in WGSR, decreasing the hydrogen to carbon monoxide molar ratio and producing water. The catalyst calcined at 500 deg C was the most promising one, leading to the highest hydrogen yield, besides the advantage of being produced at the lowest calcination temperature, requiring less energy in its preparation. (author)

Test Results of a Ten Cell Bipolar Nickel-hydrogen Battery

Science.gov (United States)

Cataldo, R. L.

1984-01-01

A study was initiated to design and evaluate a new design concept for nickel-hydrogen cells. This concept involved constructing a battery in a bipolar stack with cells consisting of a one plate for each nickel and hydrogen electrode. Preliminary designs at the system level of this concept promised improvements in both volumetric and gravimetric energy densities, thermal management, life extension, costs, and peak power capability over more conventional designs. Test results were most encouraging. This preprototype battery, built with less than ideal components and hardware, exceeded expectations. A total of 2000 LEO cycles at 80 percent depth of discharge were accrued. A cycle life goal of 30,000 cycles appears achievable with minor design changes. These improvements include advanced technology nickel electrodes, insulated bipolar plates and specifically designed frames to minimize shunt currents. The discharge rate capability of this design exceeds 25C. At the 10C discharge rate, 80% of the battery capacity can be withdrawn in six minutes. This data shows that the bipolar design is well suited for those applications requiring high peak power pulses.

Hydrogen storage alloy electrode and the nickel-hydrogen secondary battery using the electrode; Suiso kyuzo gokin denkyoku to sorewo mochiita nikkeru/suiso niji denchi

Energy Technology Data Exchange (ETDEWEB)

Ono, T. [Furukawa Electric Co. Ltd., Tokyo (Japan); Furukawa, J. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

1997-02-14

With respect to the conventional nickel-hydrogen secondary battery, pulverization of the hydrogen storage alloy due to repetition of charging-discharging cycles can be prevented by using a fluorocarbon resin as a binder in manufacture of the hydrogen storage alloy electrode; however, the inner pressure increase of the battery in case of overcharging can not be fully controlled. The invention relates to control of the inner pressure increase of the nickel-hydrogen secondary battery in case of overcharging. As to the hydrogen storage alloy electrode, the compound comprising the hydrogen storage alloy powder as a main ingredient is supported by a current collector; further, the compound particularly comprises a fluororubber as a binder. The nickel-hydrogen secondary battery equipped with the hydrogen storage alloy electrode can control the inner pressure increase of the battery in case of overcharging, and lessen decrease of the battery capacity due to repetition of charging-discharging cycles over long time. The effects are dependent on the use of the fluororubber as a binder which has good flexibility, and strong binding capacity as well as water repellency. 1 tab.

Hydrogen gas driven permeation through tungsten deposition layer formed by hydrogen plasma sputtering

International Nuclear Information System (INIS)

Uehara, Keiichiro; Katayama, Kazunari; Date, Hiroyuki; Fukada, Satoshi

2015-01-01

Highlights: • H permeation tests for W layer formed by H plasma sputtering are performed. • H permeation flux through W layer is larger than that through W bulk. • H diffusivity in W layer is smaller than that in W bulk. • The equilibrium H concentration in W layer is larger than that in W bulk. - Abstract: It is important to evaluate the influence of deposition layers formed on plasma facing wall on tritium permeation and tritium retention in the vessel of a fusion reactor from a viewpoint of safety. In this work, tungsten deposition layers having different thickness and porosity were formed on circular nickel plates by hydrogen RF plasma sputtering. Hydrogen permeation experiment was carried out at the temperature range from 250 °C to 500 °C and at hydrogen pressure range from 1013 Pa to 101,300 Pa. The hydrogen permeation flux through the nickel plate with tungsten deposition layer was significantly smaller than that through a bare nickel plate. This indicates that a rate-controlling step in hydrogen permeation was not permeation through the nickel plate but permeation though the deposition layer. The pressure dependence on the permeation flux differed by temperature. Hydrogen permeation flux through tungsten deposition layer is larger than that through tungsten bulk. From analysis of the permeation curves, it was indicated that hydrogen diffusivity in tungsten deposition layer is smaller than that in tungsten bulk and the equilibrium hydrogen concentration in tungsten deposition layer is enormously larger than that in tungsten bulk at same hydrogen pressure.

Electroless Nickel-Based Catalyst for Diffusion Limited Hydrogen Generation through Hydrolysis of Borohydride

Directory of Open Access Journals (Sweden)

Shannon P. Anderson

2013-07-01

Full Text Available Catalysts based on electroless nickel and bi-metallic nickel-molybdenum nanoparticles were synthesized for the hydrolysis of sodium borohydride for hydrogen generation. The catalysts were synthesized by polymer-stabilized Pd nanoparticle-catalyzation and activation of Al2O3 substrate and electroless Ni or Ni-Mo plating of the substrate for selected time lengths. Catalytic activity of the synthesized catalysts was tested for the hydrolyzation of alkaline-stabilized NaBH4 solution for hydrogen generation. The effects of electroless plating time lengths, temperature and NaBH4 concentration on hydrogen generation rates were analyzed and discussed. Compositional analysis and surface morphology were carried out for nano-metallized Al2O3 using Scanning Electron Micrographs (SEM and Energy Dispersive X-Ray Microanalysis (EDAX. The as-plated polymer-stabilized electroless nickel catalyst plated for 10 min and unstirred in the hydrolysis reaction exhibited appreciable catalytic activity for hydrolysis of NaBH4. For a zero-order reaction assumption, activation energy of hydrogen generation using the catalyst was estimated at 104.6 kJ/mol. Suggestions are provided for further work needed prior to using the catalyst for portable hydrogen generation from aqueous alkaline-stabilized NaBH4 solution for fuel cells.

Determination of nickel in hydrogenated fats and selected chocolate bars in Czech Republic.

Science.gov (United States)

Dohnalova, Lucie; Bucek, Pavel; Vobornik, Petr; Dohnal, Vlastimil

2017-02-15

Nickel is a metal that can be present in products containing hardened edible oils, possibly as leftover catalyst from the vegetable oil hardening process. Nickel may cause toxic effects including the promotion of cancer and contact allergy. In this work, nickel content was determined in hydrogenated vegetable fats and confectionery products, made with these fats, available on the Czech market using newly developed method combining microwave digestion and graphite furnace AAS. While concentrations of 0.086±0.014mg.kg(-1) or less were found in hydrogenated vegetable fats, the Ni content in confectionery products was significantly higher, varying between 0.742±0.066 and 3.141±0.217mg.kg(-1). Based on an average consumer basket, daily intake of nickel from vegetable fats is at least twice as low as intake from confectionery products. Based on results, the levels of nickel in neither vegetable fats nor confectionery products, do not represent a significant health risk. Copyright © 2016 Elsevier Ltd. All rights reserved.

Design of a nickel-hydrogen battery simulator for the NASA EOS testbed

Science.gov (United States)

Gur, Zvi; Mang, Xuesi; Patil, Ashok R.; Sable, Dan M.; Cho, Bo H.; Lee, Fred C.

1992-01-01

The hardware and software design of a nickel-hydrogen (Ni-H2) battery simulator (BS) with application to the NASA Earth Observation System (EOS) satellite is presented. The battery simulator is developed as a part of a complete testbed for the EOS satellite power system. The battery simulator involves both hardware and software components. The hardware component includes the capability of sourcing and sinking current at a constant programmable voltage. The software component includes the capability of monitoring the battery's ampere-hours (Ah) and programming the battery voltage according to an empirical model of the nickel-hydrogen battery stored in a computer.

IPv4 to IPv6 Transformation Schemes

Science.gov (United States)

Miyakawa, Shin

According to the recent observations of IPv4 (Internet Protocol version 4) address allocation status, it will be running out within few years. Consequently, to ensure the continuous extension of the Internet operation, introducing IPv6 (Internet Protocol version 6) protocol is surely needed. But at the same time, such transformation must be “smooth” for every Internet users and be compatible with today's IPv4 based practices. This paper describes several techniques and usage scenario which are discussed mainly in the IETF — Internet Engineering Task Force — and tried to be implemented as prototype products to transform today's Internet towards the IPv6 based one.

Perancangan dan Analisis Perbandingan Implementasi OSPF pada Jaringan IPv4 dan IPv6

Directory of Open Access Journals (Sweden)

PAULINE RAHMIATI

2016-02-01

Full Text Available Abstrak OSPF (Open Shortest Path First adalah suatu routing protokol bersifat terbuka dan didukung oleh berbagai perangkat network. IPv4 telah mencapai batas maksimum dalam jumlah alamat sehingga IPv6 merupakan solusi dalam hal tersebut. Seperti IPv4, IPv6 juga sudah mulai diimplementasikan untuk routing protokol OSPF, oleh karena itu pada penelitian ini akan dirancang suatu routing protokol OSPF IPv6 dan sebagai bahan perbandingan akan dibandingkan dengan OSPF IPv4. Software Cisco Packet Tracer 5.3 digunakan untuk mensimulasikan perancangan jaringan yang dibuat. Pada penelitian ini akan dibandingkan 2 buah jaringan berbasis routing protokol OSPF, yaitu OSPF untuk IPv4 dan IPv6. Skenario pertama dilakukan 100 kali dalam 5 kasus untuk mengetahui nilai delay OSPF IPv4 dan OSPF IPv6. Skenario kedua dilakukan pemutusan link dilakukan sebanyak 30 kali, hal yang dilihat dari pengujian ini adalah hasil trace route dari cost yang ada. Skenario ketiga dilakukan dengan mengamati waktu konvergensi dari OSPF IPv4 dan IPv6. Secara keseluruhan nilai delay OSPF IPv6 lebih kecil dibandingkan dengan OSPF IPv4 sebesar 3-6%, Trace route dan nilai cost pada OSPF IPv6 dan OSPF IPv4 sama tetapi nilai delay OSPF IPv6 lebih kecil sebesar 3-6% dan waktu konvergensi OSPF IPv4 bernilai sama dengan OSPF IPv6 yaitu 10 detik. Kata kunci: OSPF, IPv4, Ipv6, delay, konvergensi Abstract OSPF (Open Shortest Path First is a routing protocol that opened and supported by a wide range of network devices. IPv4 has reached the maximum limit on the number of addresses that IPv6 are a solution in this case. Same as IPv4, IPv6 also has begun to be implemented for the OSPF routing protocol, therefore this study wiould design an IPv6 OSPF routing protocol and as a comparison will be compared to IPv4 OSPF. Cisco Packet Tracer 5.3 software was used to simulate the made network design. This research would compare two pieces of network-based routing protocol OSPF, OSPF for IPv4 and IPv6. The

Hydrogen-absorbing alloys for the nickel-metal hydride battery

Energy Technology Data Exchange (ETDEWEB)

Mingming Geng; Jianwen Han; Feng Feng [University of Windsor, Ontario (Canada). Mechanical and Materials Engineering; Northwood, D.O. [University of Windsor, Ontario (Canada). Mechanical and Materials Engineering]|[Ryerson Polytechnic University, Toronto (Canada)

1998-12-31

In recent years, owing to the rapid development of portable electronic and electrical appliances, the market for rechargeable batteries has increased at a high rate. The nickel-metal hydride battery (Ni/MH) is one of the more promising types, because of its high capacity, high-rate charge/discharge capability and non-polluting nature. This type of battery uses a hydrogen storage alloy as its negative electrode. The characteristics of the Ni/MH battery, including discharge voltage, high-rate discharge capability and charge/discharge cycle lifetime are mainly determined by the construction of the negative electrode and the composition of the hydrogen-absorbing alloy. The negative electrode of the Ni/MH battery described in this paper was made from a mixture of hydrogen-absorbing alloy, nickel powder and polytetrafluoroethylene (PTFE). A multicomponent MmNi{sub 5}-based alloy (Mm{sub 0.95}Ti{sub 0.05}Ni{sub 3.85} Co{sub 0.45}Mn{sub 0.35}Al{sub 0.35}) was used as the hydrogen-absorbing alloy. The discharge characteristics of the negative electrode, including discharge capacity, cycle lifetime, and polarization overpotential, were studied by means of electrochemical experiments and analysis. The decay of the discharge capacity for the Ni/MH battery (AA size, 1 Ah) was about 1% after 100 charge/discharge cycles and 10% after 500 charge/discharge cycles. (author)

Modelling of hydrogen deflagration in vessels using GOTHIC

International Nuclear Information System (INIS)

Wang, L.L.; Wong, R.C.; Fluke, R.J.

1997-01-01

Simulations of hydrogen deflagration tests were performed using the discrete lumpedparameter bum model of the computer code GOTHIC. The tests were performed in small and large scale spherical vessels and a cylindrical vessel. The small vessel cases included the effects of venting, and the cylindrical tests included the effects of obstacles. The simulations were performed by sub-dividing the volumes into either five or ten 'cells', and parameters such as flame speed and hydrogen concentration were varied. Measured flame speeds were used in the simulations and the results were compared to simulations using the code 'default' flame speed. The calculated pressure transients compared well with the experimental results using the measured flame speeds in the simulations of unvented cases, whereas for vented cases, the predicted peak pressures were generally less than the measurements. However, when the code default flame speed is used, the predicted peak pressures were more consistent and generally conservative when compared with the measurements. When the default flame speeds were used for vessels without obstacles, the peak pressures obtained were higher and the bum times were shorter than the experimental measurements. This was probably due to the basis for the correlations used for default flame speed in the bum model. These correlations were derived from intermediate-scale experiments for hydrogen combustion in relatively turbulent (fans on) environments. For vessels without obstacles, laminar flame speeds were more likely. Hence, the predicted peak pressures would be expected to be higher than the experimental results. In order to account for the degree of turbulence and flame acceleration caused by the presence of obstacles, higher than default flame speeds were used in the simulation of the vessel with obstacles. It was found that twice the default flame speed provided predictions of peak pressures comparable to the measurements. Based on the simulations conducted

A simplified physics-based model for nickel hydrogen battery

Science.gov (United States)

Liu, Shengyi; Dougal, Roger A.; Weidner, John W.; Gao, Lijun

This paper presents a simplified model of a nickel hydrogen battery based on a first approximation. The battery is assumed uniform throughout. The reversible potential is considered primarily due to one-electron transfer redox reaction of nickel hydroxide and nickel oxyhydroxide. The non-ideality due to phase reactions is characterized by the two-parameter activity coefficients. The overcharge process is characterized by the oxygen reaction. The overpotentials are lumped to a tunable resistive drop to fit particular battery designs. The model is implemented in the Virtual Test Bed environment, and the characteristics of the battery are simulated and in good agreement with the experimental data within the normal operating regime. The model can be used for battery dynamic simulation and design in a satellite power system, an example of which is given.

IPv6 Security

Science.gov (United States)

Babik, M.; Chudoba, J.; Dewhurst, A.; Finnern, T.; Froy, T.; Grigoras, C.; Hafeez, K.; Hoeft, B.; Idiculla, T.; Kelsey, D. P.; López Muñoz, F.; Martelli, E.; Nandakumar, R.; Ohrenberg, K.; Prelz, F.; Rand, D.; Sciabà, A.; Tigerstedt, U.; Traynor, D.; Wartel, R.

2017-10-01

IPv4 network addresses are running out and the deployment of IPv6 networking in many places is now well underway. Following the work of the HEPiX IPv6 Working Group, a growing number of sites in the Worldwide Large Hadron Collider Computing Grid (WLCG) are deploying dual-stack IPv6/IPv4 services. The aim of this is to support the use of IPv6-only clients, i.e. worker nodes, virtual machines or containers. The IPv6 networking protocols while they do contain features aimed at improving security also bring new challenges for operational IT security. The lack of maturity of IPv6 implementations together with the increased complexity of some of the protocol standards raise many new issues for operational security teams. The HEPiX IPv6 Working Group is producing guidance on best practices in this area. This paper considers some of the security concerns for WLCG in an IPv6 world and presents the HEPiX IPv6 working group guidance for the system administrators who manage IT services on the WLCG distributed infrastructure, for their related site security and networking teams and for developers and software engineers working on WLCG applications.

PERFORMANCE ANALYSIS OF IPv4 AND IPv6 INTERNET TRAFFIC

Directory of Open Access Journals (Sweden)

Rupesh Jaiswal

2015-12-01

Full Text Available The gigantic growth of the internet communication technology has illustrated its value and benefits to private businesses, government organizations, worldwide professionals, academic institutes and individuals over the past few years. The size and range of computing devices connected to the internet, substantially increased because of IPv6 and offers the potential to establish a much more powerful internet compared to the IPv4. IPV6 developed by the IETF to deal with a shortage of IP addresses under IPv4. New features of IPv6 enhance packet processing speeds over routers, switches and end systems. These improved features will have different traffic characteristics than IPv4. The internet traffic which was earlier assumed as Poisson is now shown to have fractal characteristics as; heavy tailedness, self-similarity and long range dependency. Internet traffic showing above characteristics are found to have burstiness at multiple timescales. This behavior impacts network performance and degrades it substantially. It also increases complexity for network design and create difficulties to maintain desired QoS. IPv4 traffic has been well established as self-similar traffic. Nowadays, IPv6 forming a larger share of the internet traffic and it is pivotal to asses IPv6 with regards to fractal behavior. This will enable network designers to do necessary changes in the existing network to reconcile with IPv6. In this paper we compared IPv4 and IPv6 with respect to fractal behavioral characteristics. It is found that IPv6 shows higher degree of heavy tailedness, higher values of Hurst parameter values, higher fractal dimension values i.e. it is more self-similar, greater autocorrelation achieved even at larger lag and thus showing more burstiness.

IPv6 Essentials

CERN Document Server

Hagen, Silvia

2006-01-01

IPv6 Essentials, Second Edition provides a succinct, in-depth tour of all the new features and functions in IPv6. It guides you through everything you need to know to get started, including how to configure IPv6 on hosts and routers and which applications currently support IPv6. Aimed at system and network administrators, engineers, network designers, and IT managers, this book will help you understand, plan for, design, and integrate IPv6 into your current IPv4 infrastructure

Analysis of Pressure Variations in a Low-Pressure Nickel-Hydrogen Battery - Part 1.

Science.gov (United States)

Purushothaman, B K; Wainright, J S

2012-05-15

A low pressure nickel-hydrogen battery using either a metal hydride or gaseous hydrogen for H(2) storage has been developed for use in implantable neuroprosthetic devices. In this paper, pressure variations inside the cell for the gaseous hydrogen version are analyzed and correlated with oxygen evolution side reaction at the end of charging, the recombination of oxygen with hydrogen during charging and a subsequent rest period, and the self-discharge of the nickel electrode. About 70% of the recombination occurred simultaneously with oxygen evolution during charging and the remaining oxygen recombined with hydrogen during the 1(st) hour after charging. Self-discharge of the cell varies linearly with hydrogen pressure at a given state of charge and increased with increasing battery charge levels. The coulometric efficiency calculated based on analysis of the pressure-time data agreed well with the efficiency calculated based on the current-time data. Pressure variations in the battery are simulated accurately to predict coulometric efficiency and the state of charge of the cell, factors of extreme importance for a battery intended for implantation within the human body.

Hydrogen storage in metallic hydrides: the hydrides of magnesium-nickel alloys

International Nuclear Information System (INIS)

Silva, E.P. da.

1981-01-01

The massive and common use of hydrogen as an energy carrier requires an adequate solution to the problem of storing it. High pressure or low temperatures are not entirely satisfactory, having each a limited range of applications. Reversible metal hydrides cover a range of applications intermediate to high pressure gas and low temperature liquid hydrogen, retaining very favorable safety and energy density characteristics, both for mobile and stationary applications. This work demonstrates the technical viability of storing hydrogen in metal hydrides of magnesium-nickel alloys. Also, it shows that technology, a product of science, can be generated within an academic environment, of the goal is clear, the demand outstanding and the means available. We review briefly theoretical models relating to metal hydride properties, specially the thermodynamics properties relevant to this work. We report our experimental results on hydrides of magnesium-nickel alloys of various compositions including data on structure, hydrogen storage capacities, reaction kinetics, pressure-composition isotherms. We selected a promising alloy for mass production, built and tested a modular storage tank based on the hydrides of the alloy, with a capacity for storing 10 Nm sup(3) of hydrogen of 1 atm and 20 sup(0)C. The tank weighs 46,3 Kg and has a volume of 21 l. (author)

A low pressure bipolar nickel-hydrogen battery

Energy Technology Data Exchange (ETDEWEB)

Golben, M.; Nechev, K.; DaCosta, D.H.; Rosso, M.J.

1997-12-01

Ergenics is developing a low pressure high power rechargeable battery for electric vehicles and other large battery applications. The Hy-Stor{trademark} battery couples a bipolar nickel-hydrogen electrochemical system with the high energy storage density of metal hydride technology. In addition to its long cycle life, high specific power, and energy density, this battery offers safety and economic advantages over other rechargeable batteries. Results from preliminary testing of the first Hy-Stor battery are presented.

The interaction of water and hydrogen with nickel surfaces

NARCIS (Netherlands)

Shan, Junjun

2009-01-01

As nickel and platinum are in the same group of the periodic table, the Ni(111) and Pt(111) surfaces may be expected to show similar interaction with water and hydrogen. However in this thesis, we show these interactions for Ni(111) are quite different from those of Pt(111). Moreover, our results

A continuum damage analysis of hydrogen attack in 2.25 Cr-1Mo vessel

DEFF Research Database (Denmark)

van der Burg, M.W.D.; van der Giessen, E.; Tvergaard, Viggo

1998-01-01

A micromechanically based continuum damage model is presented to analyze the stress, temperature and hydrogen pressure dependent material degradation process termed hydrogen attack, inside a pressure vessel. Hydrogen attack (HA) is the damage process of grain boundary facets due to a chemical...... reaction of carbides with hydrogen, thus forming cavities with high pressure methane gas. Driven by the methane gas pressure, the cavities grow, while remote tensile stresses can significantly enhance the cavitation rate. The damage model gives the strain-rate and damage rate as a function...... of the temperature, hydrogen pressure and applied stresses. The model is applied to study HA in a vessel wall, where nonuniform distributions of hydrogen pressure, temperature and stresses result in a nonuniform damage distribution over the vessel wall. Stresses inside the vessel wall first tend to accelerate...

Comparison Between IPv4 to IPv6 Transition Techniques

OpenAIRE

Cordeiro, Edwin; Carnier, Rodrigo; Zucchi, Wagner L

2016-01-01

The IPv4 addresses exhaustion demands a protocol transition from IPv4 to IPv6. The original transition technique, the dual stack, is not widely deployed yet and it demanded the creation of new transition techniques to extend the transition period. This work makes an experimental comparison of techniques that use dual stack with a limited IPv4 address. This limited address might be a RFC 1918 address with a NAT at the Internet Service Provider (ISP) gateway, also known as Carrier Grade NAT (CG...

The study of hydrogen electrosorption in layered nickel foam/palladium/carbon nanofibers composite electrodes

International Nuclear Information System (INIS)

Skowronski, J.M.; Czerwinski, A.; Rozmanowski, T.; Rogulski, Z.; Krawczyk, P.

2007-01-01

In the present work, the process of hydrogen electrosorption occurring in alkaline KOH solution on the nickel foam/palladium/carbon nanofibers (Ni/Pd/CNF) composite electrodes is examined. The layered Ni/Pd/CNF electrodes were prepared by a two-step method consisting of chemical deposition of a thin layer of palladium on the nickel foam support to form Ni/Pd electrode followed by coating the palladium layer with carbon nanofibers layer by means of the CVD method. The scanning electron microscope was used for studying the morphology of both the palladium and carbon layer. The process of hydrogen sorption/desorption into/from Ni/Pd as well as Ni/Pd/CNF electrode was examined using the cyclic voltammetry method. The amount of hydrogen stored in both types of composite electrodes was shown to increase on lowering the potential of hydrogen sorption. The mechanism of the anodic desorption of hydrogen changes depending on whether or not CNF layer is present on the Pd surface. The anodic peak corresponding to the removal of hydrogen from palladium is lower for Ni/Pd/CNF electrode as compared to that measured for Ni/Pd one due to a partial screening of the Pd surface area by CNF layer. The important feature of Ni/Pd/CNF electrode is anodic peak appearing on voltammetric curves at potential ca. 0.4 V more positive than the peak corresponding to hydrogen desorption from palladium. The obtained results showed that upon storing the hydrogen saturated Ni/Pd/CNF electrode at open circuit potential, diffusion of hydrogen from carbon to palladium phase occurs due to interaction between carbon fibers and Pd sites on the nickel foam support

WLCG and IPv6 - the HEPiX IPv6 working group

Science.gov (United States)

Campana, S.; Chadwick, K.; Chen, G.; Chudoba, J.; Clarke, P.; Eliáš, M.; Elwell, A.; Fayer, S.; Finnern, T.; Goossens, L.; Grigoras, C.; Hoeft, B.; Kelsey, D. P.; Kouba, T.; López Muñoz, F.; Martelli, E.; Mitchell, M.; Nairz, A.; Ohrenberg, K.; Pfeiffer, A.; Prelz, F.; Qi, F.; Rand, D.; Reale, M.; Rozsa, S.; Sciaba, A.; Voicu, R.; Walker, C. J.; Wildish, T.

2014-06-01

The HEPiX (http://www.hepix.org) IPv6 Working Group has been investigating the many issues which feed into the decision on the timetable for the use of IPv6 (http://www.ietf.org/rfc/rfc2460.txt) networking protocols in High Energy Physics (HEP) Computing, in particular in the Worldwide Large Hadron Collider (LHC) Computing Grid (WLCG). RIPE NCC, the European Regional Internet Registry (RIR), ran out ofIPv4 addresses in September 2012. The North and South America RIRs are expected to run out soon. In recent months it has become more clear that some WLCG sites, including CERN, are running short of IPv4 address space, now without the possibility of applying for more. This has increased the urgency for the switch-on of dual-stack IPv4/IPv6 on all outward facing WLCG services to allow for the eventual support of IPv6-only clients. The activities of the group include the analysis and testing of the readiness for IPv6 and the performance of many required components, including the applications, middleware, management and monitoring tools essential for HEP computing. Many WLCG Tier 1/2 sites are participants in the group's distributed IPv6 testbed and the major LHC experiment collaborations are engaged in the testing. We are constructing a group web/wiki which will contain useful information on the IPv6 readiness of the various software components and a knowledge base (http://hepix-ipv6.web.cern.ch/knowledge-base). This paper describes the work done by the working group and its future plans.

Effect of component compression on the initial performance of an IPV nickel-hydrogen cell

Science.gov (United States)

Gahn, Randall F.

1987-01-01

An experimental method was developed for evaluating the effect of component compression on the charge and discharge voltage characteristics of a 3 1/2 in. diameter boiler plate cell. A standard boiler plate pressure vessel was modified by the addition of a mechanical feedthrough on the bottom of the vessel which permitted different compressions to be applied to the components without disturbing the integrity of the stack. Compression loadings from 0.94 to 27.4 psi were applied by suspending weights from the feedthrough rod. Cell voltages were measured for 0.96-C, 55-min charge and for 1.37-C, 35-min and 2-C, 24-min discharges. An initial change in voltage performance on both charge and discharge as the loading increased was attributed to seating of the components. Subsequent variation of the compression from 2.97 to 27.4 psi caused only minor changes in either the charge or the discharge voltages. Several one month open-circuit voltage stands and 1100 cycles under LEO conditions at the maximum loading have produced no change in performance.

Stereoselective hydrogenation of H-alkynes on boron-nickel catalysts

International Nuclear Information System (INIS)

Petrova, S.S.; Sijmer, Eh.Kh.; Amitan, I.I.

1992-01-01

It is ascertained that in the course of stereoselective hydrogenation of H-alkynes on boron-nickel catalysts the contact modified by 2-phenyl-1,5 dimethylpyrasol-2-anom in the ratio Ni(2+):BH 4 -=1:5 is the most active and selective one. Moreover, cis-alkane was prepared with the yield of 94.5% and selective of 79%

Hydrogen induced plastic damage in pressure vessel steel of 2.25Cr-1Mo

International Nuclear Information System (INIS)

Han, G.W.; Song, Y.J.

1995-01-01

2.25Cr-1Mo steel is generally employed as a hydrogenation reaction vessel material used at elevated temperature and in a hydrogen containing environment. During service of the reaction vessel, a large number of hydrogen atoms would enter its wall. When the reaction vessel is shutdown and the temperature reduces to about ambient temperature, the hydrogen atoms remaining in the wall would induce plastic damage in the steel. The mechanism of hydrogen induced plastic damage is different for various materials with different microstructures. Investigations have demonstrated that the hydrogen induced plastic damage in carbide annealed carbon steels is caused by hydrogen accelerating the initiating and growing of microvoids from the carbide particles. However, SEM examination on the fracture surface of hydrogen charged tensile specimen of 2.25Cr-1Mo steel show that a large number of fisheyes appear on the fracture surface. This indicates that hydrogen induced plastic damage in 2.25Cr-1Mo steel is related to the occurrence of fisheye cracks during plastic deformation. By means of micro-fracture mechanics to analyze fisheye crack occurrence from the first generation microvoid, the mechanism of hydrogen induced plastic damage in the pressure vessel steel is investigated

Effects of nickel on irradiation embrittlement of light water reactor pressure vessel steels

International Nuclear Information System (INIS)

2005-06-01

This TECDOC was developed under the IAEA Coordinated Research Project (CRP) entitled Effects of Nickel on Irradiation Embrittlement of Light Water Reactor Pressure Vessel (RPV) Steels. This CRP is the sixth in a series of CRPs to determine the influence of the mechanism and quantify the influence of nickel content on the deterioration of irradiation embrittlement of reactor pressure vessel steels of the Ni-Cr-Mo-V or Mn-Ni-Cr-Mo types. The scientific scope of the programme includes procurement of materials, determination of mechanical properties, irradiation and testing of specimens in power and/or test reactors, and microstructural characterization. Eleven institutes from eight different countries and the European Union participated in this CRP and six institutes conducted the irradiation experiments of the CRP materials. In addition to the irradiation and testing of those materials, irradiation experiments of various national steels were also conducted. Moreover, some institutes performed microstructural investigations of both the CRP materials and national steels. This TECDOC presents and discusses all the results obtained and the analyses performed under the CRP. The results analysed are clear in showing the significantly higher radiation sensitivity of high nickel weld metal (1.7 wt%) compared with the lower nickel base metal (1.2 wt%). These results are supported by other similar results in the literature for both WWER-1000 RPV materials, pressurized water reactor (PWR) type materials, and model alloys. Regardless of the increased sensitivity of WWER-1000 high nickel weld metal (1.7 wt%), the transition temperature shift for the WWER-1000 RPV design fluence is still below the curve predicted by the Russian code (standard for strength calculations of components and piping in NPPs - PNAE G 7-002-86). For higher fluence, no data were available and the results should not be extrapolated. Although manganese content was not incorporated directly in this CRP

[The effect of hydrogen peroxide on the electrochemical corrosion properties and metal ions release of nickel-chromium dental alloys].

Science.gov (United States)

Wang, Jue; Qiao, Guang-yan

2013-04-01

To investigate the effect of hydrogen peroxide on the electrochemical corrosion and metal ions release of nickel-chromium dental alloys. The corrosion resistance of nickel-chromium dental alloys was compared by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization curve (PD) methods in artificial saliva after immersed in different concentrations of hydrogen peroxide for 112 h. The metal ions released from nickel-chromium dental alloys to the artificial saliva were detected after electrochemical measurements using inductively coupled plasma mass spectrometry (ICP-MS). The data was statistically analyzed by analysis of variance (ANOVA) using SPSS 13.0 software package. The electrochemical experiment showed that the sequence of polarization resistance in equivalent circuit (Rct), corrosion potential (Ecorr), pitting breakdown potential (Eb), and the difference between Ecorr and Eb representing the "pseudo-passivation" (δE) of nickel-chromium alloys in artificial saliva was 30% alloys to the artificial saliva, and the order of the concentrations of metal ions was 0% corrosion resistance of nickel-chromium dental alloys decrease after immersed in different concentrations of hydrogen peroxide for 112 h. Nickel-chromium dental alloys are more prone to corrosion in the artificial saliva with the concentration of hydrogen peroxide increased, and more metal ions are released in the artificial saliva.

A study on hydrogen-storage behaviors of nickel-loaded mesoporous MCM-41.

Science.gov (United States)

Park, Soo-Jin; Lee, Seul-Yi

2010-06-01

The objective of the present work was to investigate the possibility of improving the hydrogen-storage capacity of mesoporous MCM-41 containing nickel (Ni) oxides (Ni/MCM-41). The MCM-41 and Ni/MCM-41 were prepared using a hydrothermal process as a function of Ni content (2, 5, and 10 wt.% in the MCM-41). The surface functional groups of the Ni/MCM-41 were identified by Fourier transform infrared spectroscopy (FTIR). The structure and morphology of the Ni/MCM-41 were characterized by X-ray diffraction (XRD) and field emission transmission electron microscopy (FE-TEM). XRD results showed a well-ordered hexagonal pore structure; FE-TEM also revealed, as a complementary technique, the structure and pore size. The textural properties of the Ni/MCM-41 were analyzed using N(2) adsorption isotherms at 77 K. The hydrogen-storage capacity of the Ni/MCM-41 was evaluated at 298 K/100 bar. It was found that the presence of Ni on mesoporous MCM-41 created hydrogen-favorable sites that enhanced the hydrogen-storage capacity by a spillover effect. Furthermore, it was concluded that the hydrogen-storage capacity was greatly influenced by the amount of nickel oxide, resulting in a chemical reaction between Ni/MCM-41 and hydrogen molecules. Crown Copyright © 2010. Published by Elsevier Inc. All rights reserved.

Gas-phase hydrogenation of benzene on supported nickel catalyst

Energy Technology Data Exchange (ETDEWEB)

Franco, H.A.; Phillips, M.J.

1980-06-01

The reaction of 22.66-280 Pa benzene with 72.39-122.79 Pa hydrogen on kieselguhr-supported nickel at 392.2/sup 0/-468.2/sup 0/K yielded only cyclohexane and was independent of 5.33-40 Pa cyclohexane added to the feed of the differential flow reactor. Best fit for the kinetic data was obtained with a rate equation developed by van Meerten and Coenen which assumed that all hydrogen addition steps have the same rate constant and are slow. An observed rate maximum at 458/sup 0/K may be the result of an increasing rate constant and decreasing cyclohexyl surface coverage as the temperature increases. Temperature-programed hydrogen desorption showed a series of desorption peaks at 358/sup 0/-600/sup 0/K, including one at 453/sup 0/K, which may be due to the hydrogen involved in the surface reaction.

A 37.5-kW point design comparison of the nickel-cadmium battery, bipolar nickel-hydrogen battery, and regenerative hydrogen-oxygen fuel cell energy storage subsystems for low earth orbit

International Nuclear Information System (INIS)

Manzo, M.A.; Hoberecht, M.A.

1984-01-01

Nickel-cadmium batteries, bipolar nickel-hydrogen batteries, and regenerative fuel cell storage subsystems were evaluated for use as the storage subsystem in a 37.5 kW power system for space station. Design requirements were set in order to establish a common baseline for comparison purposes. The storage subsystems were compared on the basis of effective energy density, round trip electrical efficiency, total subsystem weight and volume, and life

A 37.5-kW point design comparison of the nickel-cadmium battery, bipolar nickel-hydrogen battery, and regenerative hydrogen-oxygen fuel cell energy storage subsystems for low earth orbit

Science.gov (United States)

Manzo, M. A.; Hoberecht, M. A.

1984-01-01

Nickel-cadmium batteries, bipolar nickel-hydrogen batteries, and regenerative fuel cell storage subsystems were evaluated for use as the storage subsystem in a 37.5 kW power system for Space Station. Design requirements were set in order to establish a common baseline for comparison purposes. The storage subsystems were compared on the basis of effective energy density, round trip electrical efficiency, total subsystem weight and volume, and life.

CORPORATE MIGRATION FROM IPv4 TO IPv6 USING DIFFERENT TRANSITION MECHANISMS

OpenAIRE

Nellore Karthikeyan*, K.Chandra Mouli

2016-01-01

Currently, the Internet world is confronting the huge issue that is exhaustion of IP addresses with the IPv4 protocol. This paper contains the imperative hypothetical ideas of new era Internet Protocol IPv6 which tackles the issue of IP tending to furthermore concentrate on IPv6 address design, directing and three mechanisms of migration from IPv4 to IPv6 system: Dual Stack, Translation and Tunneling utilizing Network Simulator as Packet tracer. This paper more accentuation on network migrati...

WLCG and IPv6 – the HEPiX IPv6 working group

International Nuclear Information System (INIS)

Campana, S; Elwell, A; Goossens, L; Grigoras, C; Martelli, E; Nairz, A; Pfeiffer, A; Chadwick, K; Chen, G; Chudoba, J; Eliáš, M; Kouba, T; Clarke, P; Fayer, S; Finnern, T; Ohrenberg, K; Hoeft, B; Kelsey, D P; Muñoz, F López; Mitchell, M

2014-01-01

The HEPiX (http://www.hepix.org) IPv6 Working Group has been investigating the many issues which feed into the decision on the timetable for the use of IPv6 (http://www.ietf.org/rfc/rfc2460.txt) networking protocols in High Energy Physics (HEP) Computing, in particular in the Worldwide Large Hadron Collider (LHC) Computing Grid (WLCG). RIPE NCC, the European Regional Internet Registry (RIR), ran out ofIPv4 addresses in September 2012. The North and South America RIRs are expected to run out soon. In recent months it has become more clear that some WLCG sites, including CERN, are running short of IPv4 address space, now without the possibility of applying for more. This has increased the urgency for the switch-on of dual-stack IPv4/IPv6 on all outward facing WLCG services to allow for the eventual support of IPv6-only clients. The activities of the group include the analysis and testing of the readiness for IPv6 and the performance of many required components, including the applications, middleware, management and monitoring tools essential for HEP computing. Many WLCG Tier 1/2 sites are participants in the group's distributed IPv6 testbed and the major LHC experiment collaborations are engaged in the testing. We are constructing a group web/wiki which will contain useful information on the IPv6 readiness of the various software components and a knowledge base (http://hepix-ipv6.web.cern.ch/knowledge-base). This paper describes the work done by the working group and its future plans.

Nickel foam/polyaniline-based carbon/palladium composite electrodes for hydrogen storage

International Nuclear Information System (INIS)

Skowronski, Jan M.; Urbaniak, Jan

2008-01-01

The sandwich-like nickel/palladium/carbon electrodes exhibiting ability to absorb hydrogen in alkaline solution are presented. Electrodes were prepared by successive deposition of palladium and polyaniline layers on nickel foam substrate followed by heat treatment to give Ni/Pd/C electrode. It was shown that thermal conversion of polymer into carbon layer and subsequent thermal activation of carbon component bring about the modification of the mechanism of reversible hydrogen sorption. It was proven that carbon layer, interacting with Pd catalyst, plays a considerable role in the process of hydrogen storage. In the other series of experiments, Pd particles were dispersed electrochemically on carbon coating leading to Ni/C/Pd system. The adding of the next carbon layer resulted in Ni/C/Pd/C electrodes. Electrochemical properties of the electrodes depend on both the sequence of Pd and C layers and the preparation/activation of carbon coating. Electrochemical behavior of sandwich-like electrodes in the reaction of hydrogen sorption/desorption was characterized in 6 M KOH using the cyclic voltammetry method and the results obtained were compared to those for Ni/Pd electrode. The anodic desorption of hydrogen from electrodes free and containing carbon layer was considered after the potentiodynamic as well as potentiostatic sorption of hydrogen. The influence of the sorption potential and the time of rest of electrodes at a cut-off circuit on the kinetics of hydrogen recovery were examined. The results obtained for Ni/Pd/C electrodes indicate that the displacement of hydrogen between C and Pd phase takes place during the rest at a cut-off circuit. Electrodes containing carbon layer require longer time for hydrogen electrosorption. On the other hand, the presence of carbon layer in electrodes is advantageous because a considerable longer retention of hydrogen is possible, as compared to Pd/Ni electrode. Hydrogen stored in sandwich-like electrodes can instantly be

DICOM image secure communications with Internet protocols IPv6 and IPv4.

Science.gov (United States)

Zhang, Jianguo; Yu, Fenghai; Sun, Jianyong; Yang, Yuanyuan; Liang, Chenwen

2007-01-01

Image-data transmission from one site to another through public network is usually characterized in term of privacy, authenticity, and integrity. In this paper, we first describe a general scenario about how image is delivered from one site to another through a wide-area network (WAN) with security features of data privacy, integrity, and authenticity. Second, we give the common implementation method of the digital imaging and communication in medicine (DICOM) image communication software library with IPv6/IPv4 for high-speed broadband Internet by using open-source software. Third, we discuss two major security-transmission methods, the IP security (IPSec) and the secure-socket layer (SSL) or transport-layer security (TLS), being used currently in medical-image-data communication with privacy support. Fourth, we describe a test schema of multiple-modality DICOM-image communications through TCP/IPv4 and TCP/IPv6 with different security methods, different security algorithms, and operating systems, and evaluate the test results. We found that there are tradeoff factors between choosing the IPsec and the SSL/TLS-based security implementation of IPv6/IPv4 protocols. If the WAN networks only use IPv6 such as in high-speed broadband Internet, the choice is IPsec-based security. If the networks are IPv4 or the combination of IPv6 and IPv4, it is better to use SSL/TLS security. The Linux platform has more security algorithms implemented than the Windows (XP) platform, and can achieve better performance in most experiments of IPv6 and IPv4-based DICOM-image communications. In teleradiology or enterprise-PACS applications, the Linux operating system may be the better choice as peer security gateways for both the IPsec and the SSL/TLS-based secure DICOM communications cross public networks.

POTENTIAL FOR HYDROGEN BUILDUP IN HANFORD SEALED AIR FILLED NUCLEAR STORAGE VESSELS

International Nuclear Information System (INIS)

HEY BE

2008-01-01

This calculation is performed in accordance with HNF-PRO-8259, PHMC Calculation Preparation and Issue and addresses the question as to whether a flammable mixture of hydrogen gas can accumulate in a Hanford sealed nuclear storage vessel where the only source of hydrogen is the moisture in the air that initially filled the vessel Of specific concern is nuclear fuel inside IDENT 69-Gs, placed in Core Component Containers (CCCs) located inside Interim Storage Vaults (ISVs) at the Plutonium Finishing Plant (PFP) The CCCs are to be removed from the ISVs and placed inside a Hanford Unirradiated Fuel Package (HUFP) for transport and interim storage. The repackaging procedures mandated that no plastics were permitted, all labels and tape were to be removed and the pins to be clean and inspected Loading of the fuel into the CCC/ISV package was permitted only if it was not raining or snowing. This was to preclude the introduction of any water The purpose was to minimize the presence of any hydrogenous material inside the storage vessels. The scope of NFPA 69, 'Standard on Explosion Prevention Systems', precludes its applicability for this case. The reactor fuel pins are helium bonded. The non-fuel pins, such as the pellet stacks, are also helium bonded. The fuel pellets were sintered at temperatures that preclude any residual hydrogenous material. Hydrogen gas can be formed from neutron and gamma radiolysis of water vapor. The radiolysis reaction is quite complex involving several intermediate radicals, and competing recombination reactions. Hydrogen gas can also be formed through corrosion. This analysis takes a simplistic approach and assumes that all water vapor present in the storage vessel is decomposed into hydrogen gas. Although the analysis is needed to specifically address HUFP storage of nuclear fuel, it is equally applicable to any sealed fuel storage vessel under the assumptions listed

The development of hydrogen storage electrode alloys for nickel hydride batteries

Science.gov (United States)

Hong, Kuochih

The development of hydrogen storage electrode alloys in the 1980s resulted in the birth and growth of the rechargeable nickel hydride (Ni/MH) battery. In this paper we describe briefly a semi-empirical electrochemical/thermodynamic approach to develop/screen a hydrogen storage alloy for electrochemical application. More specifically we will discuss the AB x Ti/Zr-based alloys. Finally, the current state of the Ni/MH batteries including commercial manufacture processes, cell performance and applications is given.

Optimization of the dissolved hydrogen level in PWR to mitigate stress corrosion cracking of nickel alloys. Bibliographic review, modelling and recommendations

International Nuclear Information System (INIS)

Labousse, M.; Deforge, D.; Gressier, F.; Taunier, S.; Le Calvar, M.

2012-09-01

Nickel based alloys Stress Corrosion Cracking (SCC) has been a major concern for the Nuclear Power Plants (NPP) utilities since more than 40 years. At EDF, this issue led to the replacement of all upper vessel heads and of most of the steam generators with Alloy 600 MA tubes. Under the scope of plant lifetime extension, there is some concerns about the behaviour of Bottom Mounted Instrumentation Nozzles (BMI) made of Alloy 600 welded with Alloy 182 and a few vessel dissimilar metal welds made of Alloy 82, for only three 1450 MWe plants. It is considered for long that Primary Water Stress Corrosion Cracking (PWSCC) is influenced by the dissolved hydrogen (DH) level in primary coolant. Now, the whole community clearly understands that there is a hydrogen level corresponding to a maximum in terms of SCC susceptibility. Many experimental studies were done worldwide to optimize the hydrogen level in primary water during power operation, both in terms of SCC initiation and propagation. From these studies, most of American plants decided to increase the dissolved hydrogen level in order to mitigate crack propagation. Conversely, in Japan, based on crack initiation data, it is thought that drastically decreasing the hydrogen content would rather be beneficial. In order to consolidate EDF position, a review of laboratory tests data was made. Studies on the influence of hydrogen on nickel alloys 600 and 182 PWSCC were compiled and rationalized. Data were collapsed using a classical Gaussian model, such as initially proposed by Morton et al. An alternative model based on more phenomenological considerations was also proposed. Both models lead to similar results. The maximum susceptibility to SCC cracking appears to be rather consistent with the Ni/NiO transition, which was not taken as an initial hypothesis. Regarding crack initiation, an inverse Gaussian model was proposed. Based on the current hydrogen concentration range during power operation and considering components

Nickel-hydrogen battery testing for Hubble Space Telescope

Science.gov (United States)

Baggett, Randy M.; Whitt, Thomas H.

1989-01-01

The authors identify objectives and provide data from several nickel-hydrogen battery tests designed to evaluate the possibility of launching Ni-H2 batteries on the Hubble Space Telescope (HST). Test results from a 14-cell battery, a 12-cell battery, and a 4-cell pack are presented. Results of a thermal vacuum test to verify the battery-module/bay heat rejection capacity are reported. A 6-battery system simulation breadboard is described, and test results are presented.

Design and implementation of scalable IPv4-IPv6 internetworking gateway

Science.gov (United States)

Zhu, Guo-sheng; Yu, Shao-hua; Dai, Jin-you

2008-11-01

This paper proposed a scalable architecture of IPv4-IPv6 internetworking gateway based on EZchip 10Gbps network processor NP-1c. The Application Layer Gateway(ALG) of control plane can be upgraded without needing to modify the data forwarding plane.A SIP ALG of 3GPP IMS(IP Multimedia Subsystem)was implemented and tested under real China Next Generation Internet(CNGI) network environment.IPv4 SIP UEs can communicate with IPv6 SIP UEs through the gateway.

Bipolar nickel-hydrogen battery design

Science.gov (United States)

Koehler, C. W.; Applewhite, A. Z.; Kuo, Y.

1985-01-01

The initial design for the NASA-Lewis advanced nickel-hydrogen battery is discussed. Fabrication of two 10-cell boilerplate battery stacks will soon begin. The test batteries will undergo characterization testing and low Earth orbit life cycling. The design effectively deals with waste heat generated in the cell stack. Stack temperatures and temperature gradients are maintained to acceptable limits by utilizing the bipolar conduction plate as a heat path to the active cooling fluid panel external to the edge of the cell stack. The thermal design and mechanical design of the battery stack together maintain a materials balance within the cell. An electrolyte seal on each cell frame prohibits electrolyte bridging. An oxygen recombination site and electrolyte reservoir/separator design does not allow oxygen to leave the cell in which it was generated.

Hydrogen production with nickel powder cathode catalysts in microbial electrolysis cells

KAUST Repository

Selembo, Priscilla A.

2010-01-01

Although platinum is commonly used as catalyst on the cathode in microbial electrolysis cells (MEC), non-precious metal alternatives are needed to reduce costs. Cathodes were constructed using a nickel powder (0.5-1 μm) and their performance was compared to conventional electrodes containing Pt (0.002 μm) in MECs and electrochemical tests. The MEC performance in terms of coulombic efficiency, cathodic, hydrogen and energy recoveries were similar using Ni or Pt cathodes, although the maximum hydrogen production rate (Q) was slightly lower for Ni (Q = 1.2-1.3 m3 H2/m3/d; 0.6 V applied) than Pt (1.6 m3 H2/m3/d). Nickel dissolution was minimized by replacing medium in the reactor under anoxic conditions. The stability of the Ni particles was confirmed by examining the cathodes after 12 MEC cycles using scanning electron microscopy and linear sweep voltammetry. Analysis of the anodic communities in these reactors revealed dominant populations of Geobacter sulfurreduces and Pelobacter propionicus. These results demonstrate that nickel powder can be used as a viable alternative to Pt in MECs, allowing large scale production of cathodes with similar performance to systems that use precious metal catalysts. © 2009 Professor T. Nejat Veziroglu.

Analysis of Pressure Variations in a Low-Pressure Nickel-Hydrogen Battery – Part 1

Science.gov (United States)

Purushothaman, B. K.; Wainright, J. S.

2012-01-01

A low pressure nickel-hydrogen battery using either a metal hydride or gaseous hydrogen for H2 storage has been developed for use in implantable neuroprosthetic devices. In this paper, pressure variations inside the cell for the gaseous hydrogen version are analyzed and correlated with oxygen evolution side reaction at the end of charging, the recombination of oxygen with hydrogen during charging and a subsequent rest period, and the self-discharge of the nickel electrode. About 70% of the recombination occurred simultaneously with oxygen evolution during charging and the remaining oxygen recombined with hydrogen during the 1st hour after charging. Self-discharge of the cell varies linearly with hydrogen pressure at a given state of charge and increased with increasing battery charge levels. The coulometric efficiency calculated based on analysis of the pressure-time data agreed well with the efficiency calculated based on the current-time data. Pressure variations in the battery are simulated accurately to predict coulometric efficiency and the state of charge of the cell, factors of extreme importance for a battery intended for implantation within the human body. PMID:22423175

Hydrogenation of Levulinic Acid over Nickel Catalysts Supported on Aluminum Oxide to Prepare γ-Valerolactone

Directory of Open Access Journals (Sweden)

Jie Fu

2015-12-01

Full Text Available Four types of nickel catalysts supported on aluminum oxide (Ni/Al2O3 with different nickel loadings were synthesized using the co-precipitation method and were used for the hydrogenation of levulinic acid (LA to prepare γ-valerolactone (GVL. The synthesized Ni/Al2O3 catalysts exhibited excellent catalytic activity in dioxane, and the activity of the catalysts was excellent even after being used four times in dioxane. The catalytic activity in dioxane as a solvent was found to be superior to the activity in water. Nitrogen physisorption, X-ray diffraction, and transmission electron microscopy were employed to characterize the fresh and used catalysts. The effects of the nickel loading, temperature, hydrogen pressure, and substrate/catalyst ratio on the catalytic activity were investigated.

Influence of sulfur, phosphorus, and antimony segregation on the intergranular hydrogen embrittlement of nickel

International Nuclear Information System (INIS)

Bruemmer, S.M.; Baer, D.R.; Jones, R.H.; Thomas, M.T.

1983-01-01

The effectiveness of sulfur, phosphorus, and antimony in promoting the intergranular embrittlement of nickel was investigated using straining electrode tests in 1N H 2 SO 4 at cathodic potentials. Sulfur was found to be the critical grain boundary segregant due to its large enrichment at grain boundaries (10 4 to 10 5 times the bulk content) and the direct relationship between sulfur coverage and hydrogeninduced intergranular failure. Phosphorus was shown to be significantly less effective than sulfur or antimony in inducing the intergranular hydrogen embrittlement of nickel. The addition of phosphoru to nickel reduced the tendency for intergranular fracture and improved ductility because phosphoru segregated strongly to grain interfaces and limited sulfur enrichment. The hydrogen embrittling potency of antimony was also less than that of sulfur while its segregation propensity was considerably less. It was found that the effectiveness of segregated phosphorus and antimony in prompting inter granular embrittlement vs that of sulfur could be expressed in terms of an equivalent grain boundary sulfur coverage. The relative hydrogen embrittling potencies of sulfur, phosphorus, and antimony are discussed in reference to general mechanisms for the effect of impurity segregation on hydrogeninduced intergranular fracture

Electrolyte management considerations in modern nickel/hydrogen and nickel/cadmium cells and battery designs

Energy Technology Data Exchange (ETDEWEB)

Thaller, L.H. [The Aerospace Corporation, El Segundo, CA (United States); Zimmermann, A.H. [The Aerospace Corporation, El Segundo, CA (United States)

1996-11-01

While attention has been paid to understanding and modeling abnormal nickel/hydrogen cell behaviors, not enough attention has been paid to the potassium ion content in these cells, and more recently, in batteries. This paper will review three general areas where the potassium ion content can impact the performance and life of nickel/hydrogen and nickel/cadmium cells. Sample calculations of the concentration or volume changes that can take place within operating cells will be presented. With the aid of an accurate model of an operating cell or battery, the impact of changes of potassium ion content within a potential cell design can be estimated. All three of these areas are directly related to the volume tolerance and pore size engineering aspects of the components used in the cell or battery design. the three areas follow. (i) The gamma phase uptake of potassium ion can result in a lowering of the electrolyte concentration. This leads to a higher electrolyte resistance as well as electrolyte diffusional limitations on the discharge rate. This phenomenon also impacts the response of the cell to a reconditioning cycle. (ii) The transport of water vapor from a warmer to a cooler portion of the cell or battery under the driving force of a vapor pressure gradient has already impacted cells when water vapor condenses on a colder cell wall. This paper will explore the convective and diffusive movement of gases saturated with water vapor from a warmer plate pack to a cooler one, both with and without liquid communication. (iii) The impact of low level shunt currents in multicell configurations results in the net movement of potassium hydroxide from one part of the battery to another. This movement impacts the electrolyte volume/vapor pressure relationship within the cell or battery. (orig.)

Hydrogen Induced Intergranular Cracking of Nickel-Base Alloys.

Science.gov (United States)

1982-02-01

alloys are discussed. Experimental The steel used in the present investigation is a fully bainitic 2 1/4 Cr-lMo pressure vessel steel , ASTM A542 Class 3...Appendix A describes recent experiments performed in order to study the influence of plastic deformation on hydrogen transport in a 214 Cr-lMo steel (8...PLASTIC DEFORMATION ON HYDROGEN TRANSPORT IN 2 1/4 Cr-lMo STEEL M. Kurkela, G.S. Frankel, and R.M. Latanision Department of Materials Science and

SAFT 4{1/2} inch nickel hydrogen battery cells

Energy Technology Data Exchange (ETDEWEB)

Duquesne, D.; Lacout, B.; Sennet, A. [SAFT Advanced Batteries, Poitiers (France)

1995-12-31

SAFT Advanced Batteries has now produced over 400 high capacity 4{1/2} inch Nickel Hydrogen Battery Cells for flight programs. The 4.5 inch diameter, rabbit-ear cell design is designed to provide the anticipated energy required at the lowest practical weight. SAFT has incorporated into the design of the dry-powder nickel electrode, truly hermetic ceramic to metal seals, qualified terminal feedthroughs, high reliability mechanical design, composite pure platinum negative electrode, and zircar separator, plus more than 25 years experience in aerospace nickel cell technology, resulting in a 4{1/2} inch configuration with the 3{1/2} inch cell design carryover heritage. General performance requirements for GEO missions that SAFT cells meet are 15 years in orbit lifetime, 80% DOD, low mass to energy ratios, and flexible capacity by modifying number of electrodes in the stack. This design is qualified for geostationary orbits based on SAFT`s 3{1/2} inch qualification heritage, design verification, and cycling performed by customer Space Systems/LORAL in support of the INTELSAT VIIA and N-STAR flight programs.

Study on the combustion behavior of radiolytically generated hydrogen explosion in small scale annular vessels at the reprocessing plant

International Nuclear Information System (INIS)

Kudo, Tatsuya; Tamauchi, Yoshikazu; Arai, Nobuyuki; Dai, Wenbin; Sakaihara, Motohiro; Kanehira, Osamu

2017-01-01

Hydrogen is generated by radiolysis of water, etc. in process vessels in reprocessing plant. Usually, the hydrogen is scavenged by compressed air into vessels to prevent hydrogen explosion. When an earthquake beyond design based occurs, for example, the compressed air may stop and the hydrogen starts accumulating in the vessels, and under this condition, an ignition source might set off hydrogen explosion. Therefore, the explosion derived by the radiolytically generated hydrogen is designated as one of severe accidents on Rokkasho Reprocessing Plant in new regulatory requirements. It is important to understand the combustion behavior of hydrogen explosion inside a vessel for consideration of safety measures against the severe accident, because the influences of detonation are not considered in the design basis of vessels. Especially, the investigations about the combustion behavior which considered influence of interior obstacles inside the vessel are not performed yet. In order to investigate the combustion behavior comprehensively, explosion experiment, combustion analysis and structural analysis are carried out using the representative vessels (small scale annular vessel, small scale plate vessel, large scale annular vessel and large scale cylindrical vessel) selected from Rokkasho Reprocessing Plant. In this paper, the results of experiments and analysis of small scale annular vessel (as one of representative vessel, imitated a pulsed column in the reprocessing plant) are reported. As imitated vessels, three vessels are manufactured with different interior obstacle arrangements as follows, A) cylindrical obstacles are faithfully reproduced and are arranged based on the actual vessel, B) cylindrical obstacles are arranged more densely than the actual vessel, and C) there are no obstacles inside the vessel. Experiments of hydrogen explosion are performed under condition of stoichiometric hydrogen-air ratio (premixed hydrogen-air is used). As a result of

Nickel-hydrogen battery self-discharge mechanism and methods for its inhibition

Science.gov (United States)

Visintin, Arnaldo; Anani, Anaba; Srinivasan, Supramaniam; Appleby, A. J.; Lim, Hong S.

1992-01-01

A review of our studies on the elucidation of the self-discharge mechanism of the Ni/H2 battery and methods to inhibit this phenomena is presented. The results show that (1) the rate of heat generation from nickel hydroxide powders and from electrodes increases with increase of hydrogen pressure, simultaneously, the open-circuit potential of the nickel hydroxide electrode is shifted in a negative direction more rapidly, indicating the transformation of NiOOH to Ni(OH)2; (2) heat generation rates measured in the microcalorimeter are considerably faster for electrolyte starved electrodes than for electrolyte-flooded electrodes; (3) there is a good correlation between the extent of self-discharge, as determined by heat generation in microcalorimetric measurement and capacity change; and (4) the self-discharge in Ni/H2 battery occurs via direct reduction of the active material by pressurized hydrogen. The addition of cadmium to the electrode reduces the self-discharge.

Reverse degradation of nickel graphene junction by hydrogen annealing

Directory of Open Access Journals (Sweden)

Zhenjun Zhang

2016-02-01

Full Text Available Metal contacts are fundamental building components for graphene based electronic devices and their properties are greatly influenced by interface quality during device fabrication, leading to resistance variation. Here we show that nickel graphene junction degrades after air exposure, due to interfacial oxidation, thus creating a tunneling barrier. Most importantly, we demonstrate that hydrogen annealing at moderate temperature (300 0C is an effective technique to reverse the degradation.

IPv6 Network Security using Snort

OpenAIRE

Kaur, Ravreet; Kumar, Sumit

2013-01-01

IPv6 is new routing protocol. IPv6 is introduced by IETF mainly due IPv4 address exhaustion but it is also an enhanced version of IPv4. There are many changes in IPv6 header, some fields from IPv6 header has been deprecated from IPv6 and some are newly added. There is also common misconception among people that IPv6 is more secure than IPv4, which is not true. Now a day's intruders are targeting IPv6 networks as it is widely being accepted by many organization for their network. An intruder c...

A mathematical approach for evaluating nickel-hydrogen cells

Science.gov (United States)

Leibecki, H. F.

1986-01-01

A mathematical equation is presented which gives a quantitative relationship between time-voltage discharge curves, when a cell's ampere-hour capacity is determined at a constant discharge current. In particular the equation quantifies the initial exponential voltage decay; the rate of voltage decay; the overall voltage shift of the curve and the total capacity of the cell at the given discharge current. The results of 12 nickel-hydrogen boiler plate cells cycled to 80 percent depth-of-discharge (DOD) are discussed in association with these equations.

IPv6:n tietoturvaominaisuudet

OpenAIRE

Sorsa, Kari

2013-01-01

Opinnäytetyön tavoitteena on esitellä IPv6-protokolla ja selvittää sen tärkeimmät tietoturvaominaisuudet ja -riskit. Työtä tullaan käyttämään teoreettisena apuna Turun Ammattikorkeakoulun Lemminkäisenkadun toimipisteen laboratorioverkon siirtämisessä IPv6:een. Opinnäytetyö on jaettu kolmeen osaan. Ensimmäisessä esitellään lyhyesti IPv6:n historia ja kehitysvaiheet sekä uuden protokollan ominaisuudet. Toinen osa koostuu ominaisuus- ja tietoturvavertailusta IPv4:n ja IPv6:n välillä, jo...

Planning for IPv6

CERN Document Server

Hagen, Silvia

2011-01-01

It's official: with IPv4 network addresses close to depletion, moving to IPv6 is now business critical. This concise book helps you plan for IPv6 integration by providing a high-level overview of the technical-and nontechnical-steps involved. Many of the challenges for your enterprise are on the organizational level, and solutions differ from company to company. IPv6 Essentials author Silvia Hagen, a protocol analysis and directory service expert who's worked with IPv6 international groups and forums for 10 years, supplies answers to the issues most frequently discussed by the clients she co

Interworking between IP security and NAT-PT under IPv4/IPv6 co-existent environments

Science.gov (United States)

Ye, Run-Guo; Yu, Shu-Yao; Yang, Hong-Wei; Song, Chuck

2005-02-01

Similar to conventional NAT gateways, NAT-PT gateways break traditional TCP/IP"s end-to-end argument property; hence, any IP-based applications protected by IPSec protocol cannot traverse NAT-PT gateways properly. The interworking issues between IPSec and NAT-PT gateways under IPv4/IPv6 co-existent environments were studied: this paper first pointed out the deficiency of current NAT-Traversal scheme when interworking with NAT-PT gateways and proposed an enhanced scheme, which enabled interworking between IPSec and NAT-PT gateways and served the following three scenarios: 1) secure communication between IPv6 hosts and IPv4 hosts; 2) secure communication between IPv6 subnets and IPv4 subnets; 3) secure communication between remote IPv6 hosts and legacy IPv4 subnets.

Predicted energy densitites for nickel-hydrogen and silver-hydrogen cells embodying metallic hydrides for hydrogen storage

Science.gov (United States)

Easter, R. W.

1974-01-01

Simplified design concepts were used to estimate gravimetric and volumetric energy densities for metal hydrogen battery cells for assessing the characteristics of cells containing metal hydrides as compared to gaseous storage cells, and for comparing nickel cathode and silver cathode systems. The silver cathode was found to yield superior energy densities in all cases considered. The inclusion of hydride forming materials yields cells with very high volumetric energy densities that also retain gravimetric energy densities nearly as high as those of gaseous storage cells.

Nickel hydrogen and silver zinc battery cell modeling at the Aerospace Corporation

Energy Technology Data Exchange (ETDEWEB)

Zimmerman, A.H.

1996-02-01

A nickel hydrogen battery cell model has been fully developed and implemented at The Aerospace Corporation. Applications of this model to industry needs for the design of better cells, power system design and charge control thermal management, and long-term performance trends will be described. Present efforts will be described that are introducing the silver and zinc electrode reactions into this model architecture, so that the model will be able to predict performance for not only silver zinc cells, but also nickel zinc, silver hydrogen, and silver cadmium cells. The silver zinc cell modeling effort is specifically designed to address the concerns that arise most often in launch vehicle applications: transient response, power-on voltage regulation, hot or cold operation, electrolyte spewing, gas venting, self-discharge, separator oxidation, and oxalate crystal growth. The specific model features that are being employed to address these issues will be described.

Embrittlement of nickel-, cobalt-, and iron-base superalloys by exposure to hydrogen

Science.gov (United States)

Gray, H. R.

1975-01-01

Five nickel-base alloys (Inconel 718, Udimet 700, Rene 41, Hastelloy X, and TD-NiCr), one cobalt-base alloy (L-605), and an iron-base alloy (A-286) were exposed in hydrogen at 0.1 MN/sq m (15 psi) at several temperatures in the range from 430 to 980 C for as long as 1000 hours. These alloys were embrittled to varying degrees by such exposures in hydrogen. Embrittlement was found to be: (1) sensitive to strain rate, (2) reversible, (3) caused by large concentrations of absorbed hydrogen, and (4) not associated with any detectable microstructural changes in the alloys. These observations are consistent with a mechanism of internal reversible hydrogen embrittlement.

KOH concentration effect on the cycle life of nickel-hydrogen cells

Science.gov (United States)

Lim, H. S.; Verzwyvelt, S. A.

1985-01-01

Effects of KOH concentration on the cycle life of a sintered-type nickel electrode were studied in a boiler plate nickel-hydrogen cell at 23 C using an accelerated 45-min cycle regime at 80 percent depth of discharge. The cycle life improved greatly as the KOH concentration decreased, although the initial capacity of the cell decreased slightly. The cycle life improved by a factor of two or more when the KOH concentration was reduced from 36 to 31 percent and by a similar factor from reductions of 31 to 26 percent. For many applications, this life improvement may outweigh the initial capacity decrease.

IPV Screening and Readiness to Respond to IPV in Ob-Gyn Settings: A Patient-Physician Study

Directory of Open Access Journals (Sweden)

Katherine M. Jones

2018-01-01

Full Text Available Purpose. Intimate partner violence (IPV is a serious, preventable public health concern that largely affects women of reproductive age. Obstetrician-gynecologists (ob-gyns have a unique opportunity to identify and support women experiencing IPV to improve women’s health. Considering recent efforts to increase IPV awareness and intervention, the present study aimed to provide a current evaluation of nationally representative samples to assess ob-gyn readiness to respond to IPV as well as patient IPV-related experiences. Methods. 400 ob-gyns were randomly selected from American College of Obstetricians and Gynecologists’ (ACOG Collaborative Ambulatory Research Network. Each physician was mailed one physician survey and 25 patient surveys. Results. IPV training/education and IPV screening practices were associated with most measures of ob-gyn readiness to respond to IPV. Among respondents, 36.8% endorsed screening all patients at annual exams; however, 36.8% felt they did not have sufficient training to assist individuals in addressing IPV. Workplace encouragement of IPV response was associated with training, screening, detection, preparation/knowledge, response practices, and resources. Thirty-one percent of patients indicated their ob-gyn had asked about possible IPV experiences during their medical visit. Conclusion. Findings highlight specific gaps in ob-gyns’ IPV knowledge and response practices to be further addressed by IPV training.

An experimental study of aluminium electrowinning using a nickel-based hydrogen diffusion anode

International Nuclear Information System (INIS)

Namboothiri, Sankar; Taylor, Mark P.; Chen, John J.J.; Hyland, Margaret M.; Cooksey, Mark A.

2011-01-01

Research highlights: → Measurable depolarisation of the anode potential and formation of water vapour. → Metallic aluminium was found on the spent cathode. → HF emissions can be minimised by conducting the electrolysis at 750 o C. → The nickel based anode surface corroded during electrolysis. → Its application is constrained by the material limitation of the porous anode. - Abstract: Laboratory scale electrolysis experiments were conducted to investigate the electrowinning of aluminium using hydrogen diffusion anodes. A potassium-based electrolyte (KF-AlF 3 -Al 2 O 3 ), porous nickel alloy anode and molybdenum disk cathode were used in experiments at 750 o C. Hydrogen gas was supplied to the anode/electrolyte interface through the porous anode. Experiments were conducted in potentiostatic, galvanostatic and galvanodynamic modes. There was a measurable depolarisation of the anode potential and also anode reaction of hydrogen and oxygen ions in the bath to form water vapour was confirmed by the water vapour condensate found at the electrolysis exit gas pipe. Metallic aluminium was found on the spent cathode. The experiments conducted in the galvanodynamic mode suggested that the rate limiter for hydrogen oxidation was the availability of surface hydrogen at the anode/electrolyte interface. The anode surface corroded during electrolysis and impurities were found both in the molten bath and on the cathode.

Current Status of IPv6 Management

OpenAIRE

Astic , Isabelle; Festor , Olivier

2002-01-01

Nowadays, we are at an important time of the development of the IPv6 (Internet Protocol version 6) network. Until now, this protocol was used only between IPv6 «islands». These islands were connected by IPv4 (Internet Protocol version 4) networks. So the transport of IPv6 packets was made through IPv4 ones, or into MPLS (MultiProtocol Label Switching) tunnels. Now, that real IPv6 native equipment appears, it is possible to create real native IPv6 networks.Because in these networks, IPv4 does ...

Esimerkkiyrityksen IPv6-lähiverkko

OpenAIRE

Palkki, Ville

2013-01-01

Insinöörityön tavoitteena oli suunnitella ja toteuttaa esimerkkiyrityksen IPv6-lähiverkko. Toisena tavoitteena oli suunnitella esimerkkiyrityksen siirtyminen IPv4-protokollasta IPv6-protokollaan. Työssä käsiteltiin IPv6-protokollaa ensin teoreettisesti ja tämän jälkeen suunniteltiin sekä rakennettiin toimiva IPv6-lähiverkko. Aluksi työssä käytiin läpi IPv6-protokollan etuja verrattuna vanhaan IPv4-protokollaan. Teoriaosuudessa selvitettiin myös IPv6-protokollan rakennetta ja lähetysformaa...

Nickel-hydrogen battery state of charge management in the absence of active cooling

Energy Technology Data Exchange (ETDEWEB)

Lurie, C.; Foroozan, S. [TRW, Redondo Beach, CA (United States); Brewer, J.; Jackson, L.G. [NASA, Huntsville, AL (United States). Marshall Space Flight Center

1995-12-31

Battery management during prelaunch activities has always required special attention and careful planning. `ne transition from nickel-cadmium to nickel-hydrogen batteries, with their higher self discharge rate and lower charge efficiency, as well as longer prelaunch scenarios, have made this aspect of spacecraft management even more challenging. The NASA AXAF-I Program requires high battery state of charge at launch. The use of active cooling, to ensure adequate state of charge during prelaunch charge, trickle charge, and stand was considered and proved to be expensive and difficult to implement. Alternate approaches were considered. A procedure including optimized charging and low rate (nickel-hydrogen batteries can achieve and maintain high states of charge, in the absence of active cooling, using the approach described in this paper.

Reduction of nickel oxide particles by hydrogen studied in an environmental TEM

DEFF Research Database (Denmark)

Jeangros, Q.; Hansen, Thomas Willum; Wagner, Jakob Birkedal

2013-01-01

In situ reduction of nickel oxide (NiO) particles is performed under 1.3 mbar of hydrogen gas (H2) in an environmental transmission electron microscope (ETEM). Images, diffraction patterns and electron energy-loss spectra (EELS) are acquired to monitor the structural and chemical evolution of the...

From IPv4 to eternity - the HEPiX IPv6 working group

CERN Multimedia

CERN. Geneva

2012-01-01

The much-heralded exhaustion of the IPv4 networking address space has finally started. While many of the research and education networks have been ready and poised for years to carry IPv6 traffic, there is a well-known lack of academic institutes using the new protocols. One reason for this is an obvious absence of pressure due to the extensive use of NAT or that most currently still have sufficient IPv4 addresses. More importantly though, the fact is that moving your distributed applications to IPv6 involves much more than the routing, naming and addressing solutions provided by your campus and national networks. Application communities need to perform a full analysis of their applications, middleware and tools to confirm how much development work is required to use IPv6 and to plan a smooth transition. A new working group of HEPiX (http://www.hepix.org) was formed in Spring 2011 to address exactly these issues for the High Energy Physics community. The HEPiX IPv6 Working Group has been investigating the ma...

Development of advanced manufacturing technologies for low cost hydrogen storage vessels

Energy Technology Data Exchange (ETDEWEB)

Leavitt, Mark [Quantum Fuel Systems Technologies Worldwide, Inc., Irvine, CA (United States); Lam, Patrick [Boeing Research and Technology (BR& T), Seattle, WA (United States)

2014-12-29

The U.S. Department of Energy (DOE) defined a need for low-cost gaseous hydrogen storage vessels at 700 bar to support cost goals aimed at 500,000 units per year. Existing filament winding processes produce a pressure vessel that is structurally inefficient, requiring more carbon fiber for manufacturing reasons, than would otherwise be necessary. Carbon fiber is the greatest cost driver in building a hydrogen pressure vessel. The objective of this project is to develop new methods for manufacturing Type IV pressure vessels for hydrogen storage with the purpose of lowering the overall product cost through an innovative hybrid process of optimizing composite usage by combining traditional filament winding (FW) and advanced fiber placement (AFP) techniques. A numbers of vessels were manufactured in this project. The latest vessel design passed all the critical tests on the hybrid design per European Commission (EC) 79-2009 standard except the extreme temperature cycle test. The tests passed include burst test, cycle test, accelerated stress rupture test and drop test. It was discovered the location where AFP and FW overlap for load transfer could be weakened during hydraulic cycling at 85°C. To design a vessel that passed these tests, the in-house modeling software was updated to add capability to start and stop fiber layers to simulate the AFP process. The original in-house software was developed for filament winding only. Alternative fiber was also investigated in this project, but the added mass impacted the vessel cost negatively due to the lower performance from the alternative fiber. Overall the project was a success to show the hybrid design is a viable solution to reduce fiber usage, thus driving down the cost of fuel storage vessels. Based on DOE’s baseline vessel size of 147.3L and 91kg, the 129L vessel (scaled to DOE baseline) in this project shows a 32% composite savings and 20% cost savings when comparing Vessel 15 hybrid design and the Quantum

Separating hydrogen and oxygen evolution in alkaline water electrolysis using nickel hydroxide

Science.gov (United States)

Chen, Long; Dong, Xiaoli; Wang, Yonggang; Xia, Yongyao

2016-01-01

Low-cost alkaline water electrolysis has been considered a sustainable approach to producing hydrogen using renewable energy inputs, but preventing hydrogen/oxygen mixing and efficiently using the instable renewable energy are challenging. Here, using nickel hydroxide as a redox mediator, we decouple the hydrogen and oxygen production in alkaline water electrolysis, which overcomes the gas-mixing issue and may increase the use of renewable energy. In this architecture, the hydrogen production occurs at the cathode by water reduction, and the anodic Ni(OH)2 is simultaneously oxidized into NiOOH. The subsequent oxygen production involves a cathodic NiOOH reduction (NiOOH→Ni(OH)2) and an anodic OH− oxidization. Alternatively, the NiOOH formed during hydrogen production can be coupled with a zinc anode to form a NiOOH-Zn battery, and its discharge product (that is, Ni(OH)2) can be used to produce hydrogen again. This architecture brings a potential solution to facilitate renewables-to-hydrogen conversion. PMID:27199009

Magnetic nickel ferrite nanoparticles as highly durable catalysts for catalytic transfer hydrogenation of bio-based aldehydes

DEFF Research Database (Denmark)

He, Jian; Yang, Song; Riisager, Anders

2018-01-01

Magnetic nickel ferrite (NiFe2O4) nanoparticles were exploited as stable and easily separable heterogeneous catalysts for catalytic transfer hydrogenation (CTH) of furfural to furfuryl alcohol with 2-propanol as both the hydrogen source and the solvent providing 94% product yield at 180 degrees C...

IPv6 Testing

National Research Council Canada - National Science Library

Landis, Christopher B

2006-01-01

.... The DoD is also forming working relationships to conduct testing and share information. IPv6 was developed to resolve the issues of IPv4, mainly the limited amount of addresses and lack of security...

LEO life tests on a 75 Ah bipolar nickel-hydrogen battery

Science.gov (United States)

Lenhart, S.; Koehler, C.; Applewhite, A.

1988-01-01

The design, building, and testing of an actively cooled 10-cell 75-Ah bipolar nickel/hydrogen battery are discussed. During the last 1000 cycles, the battery has shown some evidence of elecrical performance degradation. In particular, EOC and EOD voltages have increased and decreased by several millivolts, respectively, and deep discharge capacities to a 1.0 V/cell average cutoff voltage have decreased.

DNS and BIND on IPv6

CERN Document Server

Liu, Cricket

2011-01-01

If you're preparing to roll out IPv6 on your network, this concise book provides the essentials you need to support this protocol with DNS. You'll learn how DNS was extended to accommodate IPv6 addresses, and how you can configure a BIND name server to run on the network. This book also features methods for troubleshooting problems with IPv6 forward- and reverse-mapping, and techniques for helping islands of IPv6 clients communicate with IPv4 resources. Topics include: DNS and IPv6-Learn the structure and representation of IPv6 addresses, and the syntaxes of AAAA and PTR records in the ip6.a

The 100 kW space station. [regenerative fuel cells and nickel hydrogen and nickel cadmium batteries for solar arrays

Science.gov (United States)

Mckhann, G.

1977-01-01

Solar array power systems for the space construction base are discussed. Nickel cadmium and nickel hydrogen batteries are equally attractive relative to regenerative fuel cell systems at 5 years life. Further evaluation of energy storage system life (low orbit conditions) is required. Shuttle and solid polymer electrolyte fuel cell technology appears adequate; large units (approximately four times shuttle) are most appropriate and should be studied for a 100 KWe SCB system. A conservative NiH2 battery DOD (18.6%) was elected due to lack of test data and offers considerable improvement potential. Multiorbit load averaging and reserve capacity requirements limit nominal DOD to 30% to 50% maximum, independent of life considerations.

PROPUESTA DE CONEXIÓN DE ENTORNOS IPv6 MEDIANTE UN BACKBONE MPLS/IPv4

Directory of Open Access Journals (Sweden)

Nancy Yaneth Gelvez García

2013-09-01

Full Text Available Las redes actuales MPLS/IPv4 presentan las ventajas de poder implementar ingeniería de tráfico, así como realizar diferenciación de flujos mediante clases de servicio (CoS frente a las redes con enrutamiento IP tradicional. En aras de aprovechar cualidades estratégicas durante la etapa de coexistencia entre IPv4 e IPv6 existen 4 métodos para proveer conectividad a islas IPv6 [1] remotas a través de una infraestructura de core MPLS con IPv4 nativo [2], sin embargo una de las formas que permite un rápida y fácil provisión de la misma dados los mínimos requisitos de configuración y de equipos es la de disponer túneles IPv6 en los enrutadores de acceso (CE de la red. No obstante, sus cuatro variantes (manual, GRE, 6to4 e IPv6 compatible IPv4 [3] resultan adecuadas o no según las características inherentes de la red a interconectar; por tanto este artículo presenta las ventajas y desventajas propias de la utilización de cada técnica de entunelamiento como resultado de la interconexión con los cuatro tipos de túneles de una red emulada mediante GNS3+Dynamips.

A comparison of two IPv4/IPv6 transition mechanisms - OpenVPN and IVI

Science.gov (United States)

Vu, Cong Tuan; Tran, Quang Anh; Jiang, Frank

2012-09-01

This document presents a comparison of two IPv4/IPv6 transition mechanisms. They are OpenVPN and IVI. Meanwhile OpenVPN is based on tunneling technology, IVI is a stateless IPv4/IPv6 translation technique which is developed by China Education and Research Network (CERNET). This research focus on the quantitative and qualitative comparison of these two main mechanisms; how they are applied in practical situation by the Internet Service Providers, as well as their advantages and drawbacks.

Surface treatment for hydrogen storage alloy of nickel/metal hydride battery

Energy Technology Data Exchange (ETDEWEB)

Wu, M.-S.; Wu, H.-R.; Wang, Y.-Y.; Wan, C.-C. [National Tsing Hua Univ., Hsinchu (Taiwan). Dept. of Chemical Engineering

2000-04-28

The electrochemical performance of AB{sub 2}-type (Ti{sub 0.35}Zr{sub 0.65}Ni{sub 1.2}V{sub 0.6}Mn{sub 0.2}Cr{sub 0.2}) and AB{sub 5}-type (MmB{sub 4.3}(Al{sub 0.3}Mn{sub 0.4}){sub 0.5}) hydrogen storage alloys modified by hot KOH etching and electroless nickel coating has been investigated. It is found that the alloy modified with hot KOH solution shows quick activation but at the expense of cycle-life stability. The alloy coated with nickel was effectively improved in both cycle-life stability and discharge capacity. Both the exchange and limiting current densities were increased by modifying the alloys by hot KOH solution dipping or electroless nickel coating as compared with untreated alloy electrode. The electrode with higher exchange current density and limiting current density leads to increased high-rate dischargeability. A duplex surface modified alloy (i.e., alloy first treated with hot KOH solution and then coated with nickel) has been developed, which performs satisfactorily with respect to both quick activation and long cycle life. In addition, the high-rate dischargeability for the electrode with duplex surface modification is superior to that of electrode solely treated with KOH etching or Ni plating. (orig.)

IPv6-specific misconfigurations in the DNS

NARCIS (Netherlands)

Hendriks, Luuk; de Boer, Pieter-Tjerk; Pras, Aiko

2017-01-01

With the Internet transitioning from IPv4 to IPv6, the number of IPv6-specific DNS records (AAAA) increases. Misconfigurations in these records often go unnoticed, as most systems are provided with connectivity over both IPv4 and IPv6, and automatically fall back to IPv4 in case of connection

The evolution of hydrogen and iodine by the decomposition of ammonium iodide and hydrogen iodide

International Nuclear Information System (INIS)

Ishikawa, Hiroshi; Nakane, Masanori; Ishii, Eiichi; Uehara, Itsuki; Miyake, Yoshizo

1977-01-01

As a fundamental study on thermochemical production of hydrogen from water, the evolution of hydrogen and iodine from ammonium iodide and hydrogen iodide was investigated. Hydrogen was evolved by the reaction of nickel with ammonium iodide or with hydrogen iodide, and the resulting nickel(II) iodide was decomposed thermally at 600 -- 700 0 C to form nickel. First, the iodination of powdered nickel with ammonium iodide was studied by heating their powder mixture. The maximum yield of hydrogen was obtained at a temperature near 430 0 C. The iodination of powdered nickel with gaseous ammonium iodide or with dry hydrogen iodide gas was also investigated. In this case, coating of nickel particles with a layer of resulting nickel(II) iodide prevented further conversion of nickel and lowered the reaction rate. Such a retardation effect was appreciably lessened by use of carrier. When nickel was supported on such a carrier as ''isolite'', the nickel was converted into nickel(II) iodide easily. In a reaction temperature from 400 to 500 0 C, the rate of reaction between nickel and hydrogen iodide increased slightly with the elevation of the reaction temperature. In the case of ammonium iodide, the reaction rate was higher than that for hydrogen iodide and decreased apparently with the elevation of the reaction temperature, because ammonium iodide decomposed to ammonia and hydrogen iodide. Tests using a fixed bed reactor charged with 8 -- 10 mesh ''isolite''-nickel (30 wt%) were also carried out. The maximum yield of hydrogen was about 80% for ammonium iodide at 430 0 C of reaction temperature and 60% for hydrogen iodide at 500 0 C. (auth.)

Urine nickel concentrations in nickel-exposed workers.

Science.gov (United States)

Bernacki, E J; Parsons, G E; Roy, B R; Mikac-Devic, M; Kennedy, C D; Sunderman, F W

1978-01-01

Electrothermal atomic absorption spectrometry was employed for analyses of nickel concentrations in urine samples from nickel-exposed workers in 10 occupational groups and from non-exposed workers in two control groups. Mean concentrations of nickel in urine were greatest in workers who were exposed to inhalation of aerosols of soluble nickel salts (e.g., workers in nickel plating operations and in an electrolytic nickel refinery). Less marked increases in urine nickel concentrations were found in groups of metal sprayers, nickel battery workers, bench mechanics and are welders. No significant increases in mean concentrations of nickel were found in urine samples from workers who performed grinding, buffing and polishing of nickel-containing alloys or workers in a coal gasification plant who employed Raney nickel as a hydrogenation catalyst. Measurements of nickel concentrations in urine are more sensitive and practical than measurements of serum nickel concentrations for evaluation of nickel exposures in industrial workers.

Siirtyminen IPv6-protokollaan yrityksen verkkolaitteistossa

OpenAIRE

Lindén, Kalle

2012-01-01

Tämän opinnäytetyön tarkoituksena on selvittää, mitä muutoksia Päijät-Hämeen koulutuskonsernin (PHKK) tietoverkon runkolaitteissa tarvitsee tehdä, jotta voidaan ottaa IPv6-protokolla käyttöön. Siirtyminen IPv6-protokollaan tulee olemaan välttämätön toimenpide, koska IPv4-protokollasta loppuvat uudet yksilölliset osoitteet. IPv4- ja IPv6-protokollien suurimmat erot ovat osoitekentän koon kasvaminen 32 bitistä 128 bittiin. Aluksi IPv4-osoitteistuksessa oli käytössä luokallinen osoitejärjest...

Amorphous nickel/cobalt tungsten sulfide electrocatalysts for high-efficiency hydrogen evolution reaction

Energy Technology Data Exchange (ETDEWEB)

Yang, Lun [Key Laboratory of Modern Acoustics, MOE, Institute of Acoustics and Collaborative Innovation Center of Advanced Microstructures, National Laboratory of Solid State Microstructures, Nanjing University, Nanjing 210093 (China); Wu, Xinglong, E-mail: hkxlwu@nju.edu.cn [Key Laboratory of Modern Acoustics, MOE, Institute of Acoustics and Collaborative Innovation Center of Advanced Microstructures, National Laboratory of Solid State Microstructures, Nanjing University, Nanjing 210093 (China); Department of Physics, NingBo University, NingBo 315001 (China); Zhu, Xiaoshu [Center for Analysis and Testing, Nanjing Normal University, Nanjing 210093 (China); He, Chengyu; Meng, Ming; Gan, Zhixing [Key Laboratory of Modern Acoustics, MOE, Institute of Acoustics and Collaborative Innovation Center of Advanced Microstructures, National Laboratory of Solid State Microstructures, Nanjing University, Nanjing 210093 (China); Chu, Paul K. [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China)

2015-06-30

Graphical abstract: - Highlights: • Amorphous nickel/cobalt tungsten sulfides were synthesized by a thermolytic process. • Amorphous NiWS and CoWS could realize hydrogen evolution efficiently. • Ni/Co promotion and annealing alter the porous structure and chemical bonding states. • Active sites on the surface of amorphous WS{sub x} are increased with Ni or Co doping. • Amorphous NiWS and CoWS have immense potentials in water splitting devices. - Abstract: The hydrogen evolution reaction (HER), an appealing solution for future energy supply, requires efficient and inexpensive electrocatalysts with abundant active surface sites. Although crystalline MoS{sub 2} and WS{sub 2} are promising candidates, their activity is dominated by edge sites. Amorphous tungsten sulfide prepared so far lacks the required active sites and its application has thus been hampered. In this work, nickel and cobalt incorporated amorphous tungsten sulfide synthesized by a thermolytic process is demonstrated to enhance the HER efficiency dramatically. The amorphous nickel tungsten sulfide (amorphous NiWS) annealed at 210 °C delivers the best HER performance in this system boasting a Tafel slope of 55 mV per decade and current density of 8.6 mA cm{sup −2} at 250 mV overpotential in a sustained test for 24 h. The introduction of Ni or Co into the catalyst and subsequent thermal treatment alters the porous structure and chemical bonding states thereby increasing the density of active sites on the surface.

Evaluating IPv6 Adoption in the Internet

Science.gov (United States)

Colitti, Lorenzo; Gunderson, Steinar H.; Kline, Erik; Refice, Tiziana

As IPv4 address space approaches exhaustion, large networks are deploying IPv6 or preparing for deployment. However, there is little data available about the quantity and quality of IPv6 connectivity. We describe a methodology to measure IPv6 adoption from the perspective of a Web site operator and to evaluate the impact that adding IPv6 to a Web site will have on its users. We apply our methodology to the Google Web site and present results collected over the last year. Our data show that IPv6 adoption, while growing significantly, is still low, varies considerably by country, and is heavily influenced by a small number of large deployments. We find that native IPv6 latency is comparable to IPv4 and provide statistics on IPv6 transition mechanisms used.

Adsorption of cadmium ions on nickel surface skeleton catalysts and its effect on reaction of cathodic hydrogen evolution

International Nuclear Information System (INIS)

Korovin, N.V.; Udris, E.Ya.; Savel'eva, O.N.

1986-01-01

Cadmium adsorption from different concentration CdSO 4 solutions on nickel surface skeleton catalysts (Ni ssc ) is studied by recording of polarization and potentiodynamic curves using electron microscopy and X-ray spectrometry. Main regularities of cadmium adsorption on Ni ssc are shown to be similar to those on smooth and skeleton nickel. A conclusion is drawn that increase of catalytic activity in reaction of cathodic hydrogen evolution from alkali solutions of Ni ssc base electrodes after their treatment in solutions containing Cd 2+ ions is due to irreversible desorption of strongly and averagely bound hydrogen from electrode surface at cadmium adsorption on them

A review of IPv6 security concerns

CSIR Research Space (South Africa)

Van Heerden, RP

2012-08-01

Full Text Available This study focuses on the security concerns of IPv6. We make a broad introduction to IPv6 then briefly look at the differences between the IPv6 and IPv4 protocols, their known vulnerabilities and identify some security concerns when implementing IPv...

Gas-phase Hydrogenation of Crotonaldehyde Over Nickel-on-Kieselguhr Catalyst Pellets

International Nuclear Information System (INIS)

Uraz, C.; Atalay, F.; Atalay, S.

2001-01-01

Gas phase catalytic hydrogenation of crotonaldehyde to η-butanol was investigated. A nickel based commercial catalyst produced by Harshaw was used at constant temperatures ranging from 160 to 210deg; at pressures of 1.5, 2 , and 2.5 atm and at different crotonaldehyde to hydrogen feed ratios changing from 0.134 to 0.226. The conversion of crotonaldehyde at different operating conditions were determined and the reaction rates were calculated . The experimental results were fitted to ten langmuir-Hinshelwood/ Eley Rideal type models in addition to a homogeneous kinetics modal and the best modal was identified. The effects of external and internal mass transfer resistances were found to be negligible .(authors) refs 28., 2 figs , 4 tabs

Modeling the Thermal Mechanical Behavior of a 300 K Vacuum Vessel that is Cooled by Liquid Hydrogen in Film Boiling

International Nuclear Information System (INIS)

Yang, S.Q.; Green, M.A.; Lau, W.

2004-01-01

This report discusses the results from the rupture of a thin window that is part of a 20-liter liquid hydrogen vessel. This rupture will spill liquid hydrogen onto the walls and bottom of a 300 K cylindrical vacuum vessel. The spilled hydrogen goes into film boiling, which removes the thermal energy from the vacuum vessel wall. This report analyzes the transient heat transfer in the vessel and calculates the thermal deflection and stress that will result from the boiling liquid in contact with the vessel walls. This analysis was applied to aluminum and stainless steel vessels

Low cost AB{sub 5}-type hydrogen storage alloys for a nickel-metal hydride battery

Energy Technology Data Exchange (ETDEWEB)

Jiang Lijun [General Res. Inst. for Non-Ferrous Metals, Beijing (China); Zhan Feng [General Res. Inst. for Non-Ferrous Metals, Beijing (China); Bao Deyou [General Res. Inst. for Non-Ferrous Metals, Beijing (China); Qing Guangrong [General Res. Inst. for Non-Ferrous Metals, Beijing (China); Li Yaoquan [General Res. Inst. for Non-Ferrous Metals, Beijing (China); Wei Xiuying [General Res. Inst. for Non-Ferrous Metals, Beijing (China)

1995-12-15

The studies have been carried out on utilizing Ml(NiAl){sub 5}-based alloys as a low cost negative battery electrode. The replacement of nickel by copper improved the cycle lifetime to some extent without a decrease in capacity. Using Ml(NiAlCu){sub 5} alloys, hydrogen storage alloys with good overall characteristics and low cost were obtained through substituting cobalt or silicon for nickel. The discharge capacity was further increased by increasing the lanthanum content in lanthanum-rich mischmetal. (orig.)

Device for removing hydrogen gas from the safety containment vessel of a nuclear reactor

International Nuclear Information System (INIS)

Stiefel, M.

1983-01-01

The safe processing of all concentrations of gas mixtures should be possible with such a device using a thermal recombiner of compact construction. A recombiner consisting of a metal case and diverter sheets situated in it is heated by induction. The incoming pipe for the gas mixture enriched with hydrogen and the outgoing pipe for the gas mixture with low hydrogen content are connected together by a three way valve. The third connection to the safety valve takes the larger port of the gas mixture with low hydrogen content back to the safety containment vessel. Sufficient amount of the gas mixture with low hydrogen content is taken via the three way valve to the safety containment vessel to ensure that the hydrogen content of the gas mixture taken to the recombiner remains below the 4% by volume limit. (orig./PW)

IPv6 Geolocation Using Latency Constraints

Science.gov (United States)

2014-03-01

ground truth datasets. In doing so, we investigate the following: • What is the accuracy of CBG when geolocating IPv6 hosts? • What are the accuracy...the overall PL is shorter for IPv6 than IPv4 which is consistent to what was found in recent work discussed in Section 3.5. Note that the average PL...growth of IPv6 addresses has increased significantly since 2010.The rate of increase of IPv6 usage is expected to continue; thus the need to determine

Hydrogen production by dry reforming of methane with carbon dioxide in one-dimensional nickel-based catalysts

International Nuclear Information System (INIS)

Lopez U, A. C.

2016-01-01

The main objective of this thesis is development of nickel catalysts supported over 1D matrix of cerium oxide, to be used in dry reforming methane reaction with carbon dioxide for hydrogen production. The catalysts were characterized by: Temperature Programmed Reduction (TPR), Scanning Electronic Microscopy (Sem), Surface Area (Bet method) an X Ray Diffraction (XRD). The TPR technique allowed to define reduction temperature of the active phase in the catalyst, Sem technique showed that the CeO_2 matrix had a nano rod morphology. XRD allowed to identify the crystalline phases of the catalysts. Finally, the catalysts were tested in the dry reforming methane reaction, high catalytic activity and hydrogen production were performed at 700 degrees Celsius and the catalyst with 30 wt.% of nickel. (Author)

IPv6 deployment and management

CERN Document Server

Dooley, Michael

2013-01-01

A guide for understanding, deploying, and managing Internet Protocol version 6 The growth of the Internet has created a need for more addresses than are available with Internet Protocol version 4 (IPv4)-the protocol currently used to direct almost all Internet traffic. Internet Protocol version 6 (IPv6)-the new IP version intended to ultimately succeed IPv4-will expand the addressing capacity of the Internet to support the explosive growth of users and devices on the Internet as well as add flexibility to allocating addresses and efficiency for routing traffic. IPv6 Deploy

Linear and non-linear video and TV applications using IPv6 and IPv6 multicast

CERN Document Server

Minoli, Daniel

2012-01-01

Provides options for implementing IPv6 and IPv6 multicast in service provider networks New technologies, viewing paradigms, and content distribution approaches are taking the TV/video services industry by storm. Linear and Nonlinear Video and TV Applications: Using IPv6 and IPv6 Multicast identifies five emerging trends in next-generation delivery of entertainment-quality video. These trends are observable and can be capitalized upon by progressive service providers, telcos, cable operators, and ISPs. This comprehensive guide explores these evolving directions in the TV/v

Investigating the Performance of the MPT Multipath Communication Library in IPv4 and IPv6

Directory of Open Access Journals (Sweden)

Béla Almási

2016-01-01

Full Text Available The currently used mobile devices (laptops, tablets, mobile phones contain many built-in network cards for communication (e.g. Wi-Fi, 3G, Bluetooth, etc.. A natural request could be combining the resources of the different network connection possibilities in order to increase the throughput of the communication. Unfortunately the standard IP communication technology does not support it: the communication is restricted to one IP address (i.e. to one interface. The Multipath TCP (MPTCP specification (appeared in January 2013 offers a Transport layer solution of using more than one interface in a TCP communication session. In this paper we investigate a Network layer solution. The MPT multipath communication library opens the multipath communication possibility in the Network layer. Using the MPT library, applications built on the UDP protocol are also able to perform multipath communication. The MPT library was developed by using a full dual-stack technology, which means the MPT based multipath environment can be used both in IPv4 and IPv6. Protocol version change is also possible: an IPv6 based application is able to run in an IPv4 multipath environment, and an IPv4 application can be used in an IPv6 multipath environment. In this paper we give a short overview on the MPT communication library’s working mechanism and detailed numerical examples will be shown to present how the MPT library aggregates the paths’ throughput in IPv4 and IPv6 environments. The main contribution of the paper is to demonstrate the effective throughput aggregation property of the MPT library in IPv6 and in mixed (i.e. protocol version change environments.

Nickel-hydrogen battery design for the Transporter Energy Storage Subsystem (TESS)

Science.gov (United States)

Lapinski, John R.; Bourland, Deborah S.

1992-01-01

Information is given in viewgraph form on nickel hydrogen battery design for the transporter energy storage subsystem (TESS). Information is given on use in the Space Station Freedom, the launch configuration, use in the Mobile Servicing Center, battery design requirements, TESS subassembley design, proof of principle testing of a 6-cell battery, possible downsizing of TESS to support the Mobile Rocket Servicer Base System (MBS) redesign, TESS output capacity, and cell testing.

Lattice-enabled nuclear reactions in the nickel and hydrogen gas system

International Nuclear Information System (INIS)

Nagel, David J.

2015-01-01

Thousands of lattice-enabled nuclear reaction (LENR) experiments involving electrochemical loading of deuterium into palladium have been conducted and reported in hundreds of papers. But, it appears that the first commercial LENR power generators will employ gas loading of hydrogen onto nickel. This article reviews the scientific base for LENR in the gas-loaded Ni-H system, and some of the tests of pre-commercial prototype generators based on this combination. (author)

Storage and characterization of the hydrogen in mixed oxides on base of cerium-nickel and zirconium or the aluminium

International Nuclear Information System (INIS)

Debeusscher, S.

2008-12-01

The mixed oxides based on cerium-nickel and zirconium or aluminium are able to store large quantities of hydrogen, To determine nature, reactivity and properties of hydrogen species (spill-over, direct desorption), the solid were studied by different physicochemical techniques in the dried, calcined and partially reduced states: XRD, porosity, TGA, TPR, TPA, TPD, chemical titration and inelastic neutron scattering (INS). Solids are mainly meso-porous with a common pore size at 4 nm, They are constituted of CeO 2 phase, Ce-Ni or Ce-Ni-Zr solid solution and of Ni(OH) 2 in the dried state and NiO in the calcined state. The Ni species are in various environments and the strong interactions between the cations in solid solution and at different particles interface influence their reducibility and the creation of anionic vacancies. Activation in H 2 in temperature is determining for hydrogen storage in the solid while calcination step is not necessary. INS Analyses evidence that the hydrogen species inserted during treatment in H 2 are H + (OH - ), hydride H - and H * (metallic nickel) species, present in various chemical environments, in particular for hydride species. All kinds of hydrogen species participate to the reaction during the chemical titration in agreement with the proposed hydrogenation mechanism. The study of the adsorption of hydrogen shows that this step is fast and in quantity of the same order as that measured by chemical titration. The direct desorption of H 2 is very low, linked to the presence of hydrogen in interaction with metallic nickel (H *- .). Desorption of water is also observed, in parallel, corresponding to the elimination of groups. The hydride species are not desorbed. These various observations allow connecting hydrogen species properties with their localization in the structure and to model active sites. (author)

TRANSPORTE DE VOZ (VoIP SOBRE REDES IPv4 e IPv6

Directory of Open Access Journals (Sweden)

Fausto Alexander Gamboa

2012-05-01

Full Text Available El presente artículo tiene como finalidad evaluar el comportamiento de la VoIP en redes IPv6 y compararlo con IPv4, de igual manera presentar las arquitecturas que la soportan. Con el fin de que los resultados sean los más cercanos a la realidad, el artículo no solo se soporta en simulaciones si no en implementaciones reales. Dentro de las conclusiones más sobresalientes se encontró que la VoIP6 presenta mejor rendimiento ante el Jitter y el retardo que VoIPv4.

Submerged-arc wire electrodes with nickel-plated surfaces

International Nuclear Information System (INIS)

Hagen, H. vom.

1976-01-01

The article reports on the development of SANWELD welding rods at GARHYTTAN's which is a wire free of impurities, copper, and hydrogen with a nickel surface. It is producted according to the SANBOND process. The wire has an optimum of mechanical quality grades depending on the powder used for welding, especially an improvement of notch impact strength. The elongation, especially the long-time values, are improved, hydrogen cracks are excluded depending on the correct powder or protective gas, and the low-temparature values are improved. An attendant phenomenon, which is not unimportant, is that the wires are practically corrosion-resistant in the non-welded state. The wire is suitable for submerged-arc welding in steam boilers and pressure vessels. (IHoe) [de

IPv6 addressing proxy: mapping native addressing from legacy technologies and devices to the Internet of Things (IPv6).

Science.gov (United States)

Jara, Antonio J; Moreno-Sanchez, Pedro; Skarmeta, Antonio F; Varakliotis, Socrates; Kirstein, Peter

2013-05-17

Sensors utilize a large number of heterogeneous technologies for a varied set of application environments. The sheer number of devices involved requires that this Internet be the Future Internet, with a core network based on IPv6 and a higher scalability in order to be able to address all the devices, sensors and things located around us. This capability to connect through IPv6 devices, sensors and things is what is defining the so-called Internet of Things (IoT). IPv6 provides addressing space to reach this ubiquitous set of sensors, but legacy technologies, such as X10, European Installation Bus (EIB), Controller Area Network (CAN) and radio frequency ID (RFID) from the industrial, home automation and logistic application areas, do not support the IPv6 protocol. For that reason, a technique must be devised to map the sensor and identification technologies to IPv6, thus allowing homogeneous access via IPv6 features in the context of the IoT. This paper proposes a mapping between the native addressing of each technology and an IPv6 address following a set of rules that are discussed and proposed in this work. Specifically, the paper presents a technology-dependent IPv6 addressing proxy, which maps each device to the different subnetworks built under the IPv6 prefix addresses provided by the internet service provider for each home, building or user. The IPv6 addressing proxy offers a common addressing environment based on IPv6 for all the devices, regardless of the device technology. Thereby, this offers a scalable and homogeneous solution to interact with devices that do not support IPv6 addressing. The IPv6 addressing proxy has been implemented in a multi-protocol Sensors 2013, 13 6688 card and evaluated successfully its performance, scalability and interoperability through a protocol built over IPv6.

IPv6 Addressing Proxy: Mapping Native Addressing from Legacy Technologies and Devices to the Internet of Things (IPv6

Directory of Open Access Journals (Sweden)

Peter Kirstein

2013-05-01

Full Text Available Sensors utilize a large number of heterogeneous technologies for a varied set of application environments. The sheer number of devices involved requires that this Internet be the Future Internet, with a core network based on IPv6 and a higher scalability in order to be able to address all the devices, sensors and things located around us. This capability to connect through IPv6 devices, sensors and things is what is defining the so-called Internet of Things (IoT. IPv6 provides addressing space to reach this ubiquitous set of sensors, but legacy technologies, such as X10, European Installation Bus (EIB, Controller Area Network (CAN and radio frequency ID (RFID from the industrial, home automation and logistic application areas, do not support the IPv6 protocol. For that reason, a technique must be devised to map the sensor and identification technologies to IPv6, thus allowing homogeneous access via IPv6 features in the context of the IoT. This paper proposes a mapping between the native addressing of each technology and an IPv6 address following a set of rules that are discussed and proposed in this work. Specifically, the paper presents a technology-dependent IPv6 addressing proxy, which maps each device to the different subnetworks built under the IPv6 prefix addresses provided by the internet service provider for each home, building or user. The IPv6 addressing proxy offers a common addressing environment based on IPv6 for all the devices, regardless of the device technology. Thereby, this offers a scalable and homogeneous solution to interact with devices that do not support IPv6 addressing. The IPv6 addressing proxy has been implemented in a multi-protocol Sensors 2013, 13 6688 card and evaluated successfully its performance, scalability and interoperability through a protocol built over IPv6.

IPv6 Addressing Proxy: Mapping Native Addressing from Legacy Technologies and Devices to the Internet of Things (IPv6)

Science.gov (United States)

Jara, Antonio J.; Moreno-Sanchez, Pedro; Skarmeta, Antonio F.; Varakliotis, Socrates; Kirstein, Peter

2013-01-01

Sensors utilize a large number of heterogeneous technologies for a varied set of application environments. The sheer number of devices involved requires that this Internet be the Future Internet, with a core network based on IPv6 and a higher scalability in order to be able to address all the devices, sensors and things located around us. This capability to connect through IPv6 devices, sensors and things is what is defining the so-called Internet of Things (IoT). IPv6 provides addressing space to reach this ubiquitous set of sensors, but legacy technologies, such as X10, European Installation Bus (EIB), Controller Area Network (CAN) and radio frequency ID (RFID) from the industrial, home automation and logistic application areas, do not support the IPv6 protocol. For that reason, a technique must be devised to map the sensor and identification technologies to IPv6, thus allowing homogeneous access via IPv6 features in the context of the IoT. This paper proposes a mapping between the native addressing of each technology and an IPv6 address following a set of rules that are discussed and proposed in this work. Specifically, the paper presents a technology-dependent IPv6 addressing proxy, which maps each device to the different subnetworks built under the IPv6 prefix addresses provided by the internet service provider for each home, building or user. The IPv6 addressing proxy offers a common addressing environment based on IPv6 for all the devices, regardless of the device technology. Thereby, this offers a scalable and homogeneous solution to interact with devices that do not support IPv6 addressing. The IPv6 addressing proxy has been implemented in a multi-protocol card and evaluated successfully its performance, scalability and interoperability through a protocol built over IPv6. PMID:23686145

Teardown analysis of a ten cell bipolar nickel-hydrogen battery

Science.gov (United States)

Manzo, M. A.; Gonzalez-Sanabria, O. D.; Herzau, J. S.; Scaglione, L. J.

1984-01-01

Design studies have identified bipolar nickel-hydrogen batteries as an attractive storage option for high power, high voltage applications. A pre-prototype Ni-H2 battery was designed, assembled and tested in the early phases of a concept verification program. The initial stack was built with available hardware and components from past programs. The stack performed well. After 2000 low-earth-orbit cycles the stack was dismantled in order to allow evaluation and analysis of the design and components. The results of the teardown analysis and recommended modifications are discussed.

KOH concentration effect on the cycle life of nickel-hydrogen cells. 4: Results of failure analyse

Science.gov (United States)

Lim, H. S.; Verzwyvelt, S. A.

1989-01-01

Effects of KOH concentrations on failure modes and mechanisms of nickel-hydrogen cells were studied using long cycled boiler plate cells containing electrolytes of various KOH concentrations ranging 21 to 36 percent. Life of these cells were up to 40,000 cycles in an accelerated low earth orbit (LEO) cycle regime at 80 percent depth of discharge. An interim life test results were reported earlier in J. Power Sources, 22, 213-220, 1988. The results of final life test, end-of-life cell performance, and teardown analyses are discussed. These teardown analyses included visual observations, measurements of nickel electrode capacity in an electrolyte-flooded cell, dimensional changes of cell components, SEM studies on cell cross section, BET surface area and pore volume distribution in cycled nickel electrodes, and chemical analyses. Cycle life of a nickel-hydrogen cell was improved tremendously as KOH concentration was decreased from 36 to 31 percent and from 31 to 26 percent while effect of further concentration decrease was complicated as described in our earlier report. Failure mode of high concentration (31 to 36 percent) cells was gradual capacity decrease, while that of low concentration (21 to 26 percent) cells was mainly formation of a soft short. Long cycled (25,000 to 40,000 cycles) nickel electrodes were expanded more than 50 percent of the initial value, but no correlation was found between this expansion and measured capacity. All electrodes cycled in low concentration (21 to 26 percent) cells had higher capacity than those cycled in high concentration (31 to 36 percent) cells.

Migrating Applications to IPv6

CERN Document Server

York, Dan

2011-01-01

If IPv6 is to be adopted on a large scale, the applications running on desktop systems, laptops, and even mobile devices need to work just as well with this protocol as they do with IPv4. This concise book takes you beyond the network layer and helps you explore the issues you need to address if you are to successfully migrate your apps to IPv6. It's ideal for application developers, system/network architects, product managers, and others involved in moving your network to IPv6. Explore changes you need to make in your application's user interfaceMake sure your application is retrieving corre

HIV Positive Diagnosis During Pregnancy Increases Risk of IPV Postpartum Among Women with No History of IPV in Their Relationship.

Science.gov (United States)

Groves, Allison K; Reyes, H Luz McNaughton; Moodley, Dhayendre; Maman, Suzanne

2017-07-24

There has been limited study of whether and for whom physical intimate partner violence (IPV) is a consequence of an HIV-positive diagnosis. Per the diathesis stress model, the consequences of HIV infection may be worse for women with a history of IPV. We hypothesize that the positive association between HIV diagnosis in pregnancy and postpartum IPV will be exacerbated for women with a history of IPV. Data come from a prospective cohort study with 1015 participants who completed a baseline antenatal and 9-month postpartum visit. Using logistic regression analyses, we found a statistically significant interaction between HIV diagnosis, history of IPV and postpartum IPV (AOR: 0.40, 95% CI 0.17-0.96). The findings were in the opposite direction as expected: HIV-diagnosis was not associated with IPV for women with a history of IPV (AOR: 2.17, 95% CI 1.06, 4.42). However, HIV-positive women without a history of IPV faced more than two times the risk of incident postpartum IPV than HIV-negative women (AOR: 2.17, 95% CI 1.06, 4.42). Interventions to reduce incident and ongoing IPV during the perinatal period are needed.

The effect of urea on microstructures of Ni{sub 3}S{sub 2} on nickel foam and its hydrogen evolution reaction

Energy Technology Data Exchange (ETDEWEB)

Jinlong, Lv, E-mail: ljltsinghua@126.com [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China); Tongxiang, Liang, E-mail: txliang@mail.tsinghua.edu.cn [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China)

2016-11-15

The effects of urea concentration on microstructures of Ni{sub 3}S{sub 2}formed on nickel foam and its hydrogen evolution reaction were investigated. The Ni{sub 3}S{sub 2} nanosheets with porous structure were formed on nickel foam during hydrothermal process due to low urea concentration. While high urea concentration facilitated the forming of Ni{sub 3}S{sub 2} nanotube arrays. The resulting Ni{sub 3}S{sub 2} nanotube arrays exhibited higher catalytic activity than Ni3S2nanosheets for hydrogen evolution reaction. This was mainly attributed to a fact that Ni{sub 3}S{sub 2} nanotube arrays facilitated diffusion of electrolyte for hydrogen evolution reaction. - Graphical abstract: The resulting Ni{sub 3}S{sub 2} nanotube arrays exhibited higher catalytic activity than Ni{sub 3}S{sub 2} nanosheets for hydrogen evolution reaction. This was mainly attributed to a fact that Ni{sub 3}S{sub 2} nanotube arrays facilitated diffusion of electrolyte for hydrogen evolution reaction and hydrogen evolution. - Highlights: • Urea promoted to forming more Ni{sub 3}S{sub 2} nanotube arrays on nickel foam. • Ni{sub 3}S{sub 2} nanotube arrays showed higher catalytic activity in alkaline solution. • Ni{sub 3}S{sub 2} nanotube arrays promoted electron transport and reaction during the HER.

A review of IPv6 security concerns

CSIR Research Space (South Africa)

Van Heerden, RP

2012-11-01

Full Text Available This study focuses on the security concerns of IPv6. A broad introduction to IPv6 is made then briefly the differences between the IPv6 and IPv4 protocols are looked at, their known vulnerabilities and this identifies some security concerns when...

NICKEL PLATING PROCESS

Science.gov (United States)

Hoover, T.B.; Zava, T.E.

1959-05-12

A simplified process is presented for plating nickel by the vapor decomposition of nickel carbonyl. In a preferred form of the invention a solid surface is nickel plated by subjecting the surface to contact with a mixture containing by volume approximately 20% nickel carbonyl vapor, 2% hydrogen sulfide and .l% water vapor or 1% oxygen and the remainder carbon dioxide at room temperature until the desired thickness of nickel is obtained. The advantage of this composition over others is that the normally explosive nickel carbonyl is greatly stabilized.

Caracterización de IPv6

Directory of Open Access Journals (Sweden)

Carlos A. Castillo Medina

2013-05-01

Full Text Available The present paper attempts to survey the current state of the network protocol called IPv6; starting from the evolution of IPv4 (which motivated the design of new features to the details that are comprised in the new version of the Internet Protocol. The main sections explain the drawbacks of IPv4 that can be overcome by implementing IPv6, highlighting aspects such as security, mobility, and Quality of Service (QoS.

IPv4 to IPv6 Transition: Optimal Routing Protocol within Dual Stack and Tunneling

OpenAIRE

Aparna Sivaprakash; S. Kayalvizhi

2016-01-01

The number of global internet users has been growing exponentially, necessitating a much larger number of unique IP addresses for all the connected networking devices. The prevalent IP version 4 is not able to meet the current requirement for IP addresses. To meet the future IP address requirement, a new version IPv6 has been introduced since 1999. However IPv6 is not backward compatible with IPv4.since it is not possible to migrate all the networking devices to ...

Intimate partner violence (IPV)

DEFF Research Database (Denmark)

Rasch, Vibeke; Van, Toan Ngo; Nguyen, Hanh Thi Thuy

2018-01-01

BACKGROUND: Intimate partner violence (IPV) is a global problem that affects one-third of all women. The present study aims to develop and determine the validity of a screening instrument for the detection of IPV in pregnant women in Tanzania and Vietnam and to determine the minimum number...

Analisis Performa File Transport Protocol pada Perbandingan Metode IPv4 Murni, IPv6 Murni dan Tunneling 6to4 Berbasis Router Mikrotik

Directory of Open Access Journals (Sweden)

Siswo Wardoyo

2014-09-01

Full Text Available The use of IPv4 which has more than 30 years led to the capacity of available addresses is running out availability. Currently emerging new generation IP (IPnext generation is IPv6. Many methods for the implementation of IPv6, one with tunneling. 6to4 is a tunneling method that can be directly implemented on an IPv4 network. This study compared the performance level of a pure IPv4 network, IPv6 6to4 tunneling with pure and searching FTP throughput performance. Throughput results obtained pure IPv6 is smaller than the value of 42.9% pure IPv4 throughput, 6to4 tunneling is smaller than 39.4% pure IPv4 and IPv6 pure value 53.626% greater throughput than 6to4 tunneling configuration.

Ni(0-CMC-Na Nickel Colloids in Sodium Carboxymethyl-Cellulose: Catalytic Evaluation in Hydrogenation Reactions

Directory of Open Access Journals (Sweden)

Abdallah Karim

2011-01-01

Full Text Available A recyclable catalyst, Ni(0-CMC-Na, composed of nickel colloids dispersed in a water soluble bioorganic polymer, sodium carboxymethylcellulose (CMC-Na, was synthesized by a simple procedure from readily available reagents. The catalyst thus obtained is stable and highly active in alkene hydrogenations.

Hydrogen production by steam reforming of liquefied natural gas over a nickel catalyst supported on mesoporous alumina xerogel

Science.gov (United States)

Seo, Jeong Gil; Youn, Min Hye; Cho, Kyung Min; Park, Sunyoung; Song, In Kyu

Mesoporous alumina xerogel (A-SG) is prepared by a sol-gel method for use as a support for a nickel catalyst. The Ni/A-SG catalyst is then prepared by an impregnation method, and is applied to hydrogen production by steam reforming of liquefied natural gas (LNG). The effect of the mesoporous alumina xerogel support on the catalytic performance of Ni/A-SG catalyst is investigated. For the purpose of comparison, a nickel catalyst supported on commercial alumina (A-C) is also prepared by an impregnation method (Ni/A-C). Both the hydroxyl-rich surface and the electron-deficient sites of the A-SG support enhance the dispersion of the nickel species on the support during the calcination step. The formation of the surface nickel aluminate phase in the Ni/A-SG catalyst remarkably increases the reducibility and stability of the catalyst. Furthermore, the high-surface area and the well-developed mesoporosity of the Ni/A-SG catalyst enhance the gasification of surface hydrocarbons that are adsorbed in the reaction. In the steam reforming of LNG, the Ni/A-SG catalyst exhibits a better catalytic performance than the Ni/A-C catalyst in terms of LNG conversion and hydrogen production. Moreover, the Ni/A-SG catalyst shows strong resistance toward catalyst deactivation.

IPv6 geolokace a vizualizace

OpenAIRE

Suchomel, Tomáš

2011-01-01

Tato diplomová práce se zabývá problematikou geolokace IPv6 adres a vizualizace jejich lokalit. Má za úkol prozkoumat oblast IPv6, dále porovnává současné přístupy ke geolokaci. Jejím hlavním cílem je vybudovat systém, který dokáže vytvořit geolokační databázi s pravidelnou aktualizací a který bude schopen zobrazit geografickou lokalitu IPv6 adresy na světové mapě. Geolokační systém nejprve získá geografické adresy pro jednotlivé prefixy IPv6 z veřejně přístupného systému Whois. Tyto adresy t...

The association between child exposure to intimate partner violence (IPV) and perpetration of IPV in adulthood-A systematic review.

Science.gov (United States)

Kimber, Melissa; Adham, Sami; Gill, Sana; McTavish, Jill; MacMillan, Harriet L

2018-02-01

Increasingly recognized as a distinct form of childhood maltreatment, children's exposure to intimate partner violence (IPV) has been shown to be associated with an array of negative psychosocial outcomes, including elevated risk for additional violence over the life course. Although studies have identified child exposure to IPV as a predictor of IPV perpetration in adulthood, no review has critically evaluated the methodology of this quantitative work. The present study examines the association between childhood exposure to IPV and the perpetration of IPV in adulthood based on a systematic review of the literature from inception to January 4, 2016. Databases searched included Medline, Embase, PsycINFO, CINAHL, Cochrane Database of Systematic Reviews, Sociological Abstracts and ERIC. Database searches were complemented with backward and forward citation chaining. Studies were critically appraised using the Quality Assessment Tool for Observational Cohort and Cross-Sectional Studies. Of 5601 articles identified by the search, 19 studies were included for data extraction. Sixteen of these studies found that child exposure to IPV was significantly and positively associated with adult IPV perpetration; three studies reported null findings. The methodological quality of the studies was low. Work thus far has tended to focus on child exposure to physical IPV and the perpetration of physical IPV within heterosexual contexts. In addition, measures of child exposure to IPV vary in their classification of what exposure entails. We critically discuss the strengths and limitations of the existing evidence and the theoretical frameworks informing this work. Copyright © 2017 Elsevier Ltd. All rights reserved.

Highly efficient electrochemical hydrogen evolution based on nickel diselenide nanowall film

Science.gov (United States)

Tang, Chun; Xie, Lisi; Sun, Xuping; Asiri, Abdullah M.; He, Yuquan

2016-05-01

In this letter, we report on hydrothermal growth of nickel diselenide nanowall film on carbon cloth (NiSe2 NW/CC) through topotactic transformation from a Ni(OH)2 precursor based on anion exchange reactions. When tested as an integrated 3D hydrogen-evolving cathode in strongly acidic media, NiSe2 NW/CC exhibits outstanding catalytic activity superior to its powder counterpart and strong long-term durability. It displays 10 and 100 mA cm-2 at overpotentials of 145 and 183 mV, respectively, with its catalytic activity being retained for 40 h.

The Deployment of IPv6 in an IPv4 World and Transition Strategies.

Science.gov (United States)

Bouras, C.; Ganos, P.; Karaliotas, A.

2003-01-01

The current version of the IP protocol, IPv4, is the most widely used protocol in computer networks. This article describes mechanisms that can be used to facilitate the transition to the new version of the IP protocol, IPv6, and examines usability, usefulness and manageability. Describes how some of these mechanisms were applied to the Greek…

The production deployment of IPv6 on WLCG

Science.gov (United States)

Bernier, J.; Campana, S.; Chadwick, K.; Chudoba, J.; Dewhurst, A.; Eliáš, M.; Fayer, S.; Finnern, T.; Grigoras, C.; Hartmann, T.; Hoeft, B.; Idiculla, T.; Kelsey, D. P.; López Muñoz, F.; Macmahon, E.; Martelli, E.; Millar, A. P.; Nandakumar, R.; Ohrenberg, K.; Prelz, F.; Rand, D.; Sciabà, A.; Tigerstedt, U.; Voicu, R.; Walker, C. J.; Wildish, T.

2015-12-01

The world is rapidly running out of IPv4 addresses; the number of IPv6 end systems connected to the internet is increasing; WLCG and the LHC experiments may soon have access to worker nodes and/or virtual machines (VMs) possessing only an IPv6 routable address. The HEPiX IPv6 Working Group has been investigating, testing and planning for dual-stack services on WLCG for several years. Following feedback from our working group, many of the storage technologies in use on WLCG have recently been made IPv6-capable. This paper presents the IPv6 requirements, tests and plans of the LHC experiments together with the tests performed on the group's IPv6 test-bed. This is primarily aimed at IPv6-only worker nodes or VMs accessing several different implementations of a global dual-stack federated storage service. Finally the plans for deployment of production dual-stack WLCG services are presented.

IPv6 Network Administration

CERN Document Server

Murphy, Niall Richard

2009-01-01

This essential guide explains what works, what doesn't, and most of all, what's practical about IPv6--the next-generation Internet standard. A must-have for network administrators everywhere looking to fix their network's scalability and management problems. Also covers other IPv6 benefits, such as routing, integrated auto-configuration, quality-of-services (QoS), enhanced mobility, and end-to-end security.

Effect of controlled deactivation on the thermochemical characteristics of hydrogen adsorption on skeletal nickel from sodium hydroxide-water solutions

Science.gov (United States)

Prozorov, D. A.; Lukin, M. V.; Ulitin, M. V.

2013-04-01

Differential heats of adsorption in a wide range of surface coverage and maximum amounts of adsorbed hydrogen are determined by adsorption calorimetry on partially deactivated skeletal nickel from aqueous solutions of sodium hydroxide. The effect of the composition of solutions on the values of limiting adsorption and adsorption equilibria of individual forms of hydrogen is shown.

Magnetic effects of interstitial hydrogen in nickel

Energy Technology Data Exchange (ETDEWEB)

León, Andrea [Departamento de Física, Universidad Técnica Federico Santa María, Valparaíso (Chile); Velásquez, E.A. [Facultad de Física y Centro de Investigación en Nanotecnología y Materiales Avanzados CIEN-UC, Pontificia Universidad Católica de Chile, Santiago (Chile); Centro para el Desarrollo de la Nanociencia y la Nanotecnología CEDENNA, Santiago (Chile); Grupo de Investigación en Modelamiento y Simulación Computacional, Universidad de San Buenaventura Sec. Medellín, Medellín (Colombia); Mazo-Zuluaga, J. [Grupo de Instrumentación Científica y Microelectrónica, Grupo de Estado Sólido, IF-FCEN, Universidad de Antioquia UdeA, Calle 70 No. 52-21, Medellín (Colombia); Mejía-López, J. [Facultad de Física y Centro de Investigación en Nanotecnología y Materiales Avanzados CIEN-UC, Pontificia Universidad Católica de Chile, Santiago (Chile); Centro para el Desarrollo de la Nanociencia y la Nanotecnología CEDENNA, Santiago (Chile); Florez, J.M. [Departamento de Física, Universidad Técnica Federico Santa María, Valparaíso (Chile); and others

2017-01-01

Hydrogen storage in materials is among the most relevant fields when thinking about energy conversion and storage. In this work we present a study that responds to a couple of questions concerning induced electronic changes that H produces in ferromagnetic nickel (Ni) host. We calculate and explain the change of magnetic properties of Ni with different concentrations of H. Density functional theory calculations (DFT) were performed for super-cells of fcc Ni with interstitial H in octahedral sites at different concentrations. In order to physically explain the effect of magnetization diminishing as the hydrogen concentration increases, we propose a simple Stoner type of model to describe the influence of the H impurity on the magnetic properties of Ni. The exchange splitting reduction, as shown in first principles calculations, is clearly explained within this physical model. Using a paramagnetic Ni fcc band with variable number of electrons and a Stoner model allow us to obtain the correct trend for the magnetic moment of the system as a function of the H concentration. - Highlights: • We calculate and explain the change of magnetic properties of Ni with different concentrations of H. • We propose a simple Stoner type of model to describe the influence of the H impurity on the magnetic properties of Ni. • The band exchange splitting reduction as the H concentration increases, is a consequence of the competition between the band energy term (kinetic energy) and the ferromagnetic energy term (Weiss field).

Effect of nickel content on mechanical properties and fracture toughness of weld metal of WWER-1000 reactor vessel welded joints

International Nuclear Information System (INIS)

Zubchenko, A.S.; Vasilchenko, G.S.; Starchenko, E.G.; Nosov, S.I.

2004-01-01

Welding of WWER-1000 reactor vessel of steel 15X2HMPHIA is performed using the C B -12X2H2MAA wire and PHI-16 or PHI-16A flux. Nickel content in the weld metal usually lays within the limits 1.2-1.9%. The experimental data is shown on the weld metal with the nickel contents 1.28-2.45% after irradiation with fluence up to 260.10 22 n/m 2 at energy more than 0.5 MEV. The embrittlement was measured by shift of critical brittleness temperature. Has appeared, that the weld metal with the low nickel content is the least responsive to irradiation embrittlement. The mechanical properties and fracture toughness of the weld metal with the contents of a nickel less than 1.3% are studied. Specimens CT-1T are tested, the 'master-curve', and its confidence bounds with probability of destruction 5 and 95% is built. 'Master-curve' in the specified confidence interval is affirmed by CT-4T specimens test data. Is shown, that the mechanical properties and fracture toughness of the weld metal with the contents of nickel less than 1.3% satisfy the normative requirements

Effect of water flow rate and water chemistry on corrosion environment in reactor pressure vessel bottom of BWRs

Energy Technology Data Exchange (ETDEWEB)

Ichikawa, Nagayoshi; Hemmi, Yukio; Takagi, Junichi; Urata, Hidehiro [Toshiba Corp., Kawasaki, Kanagawa (Japan)

1999-07-01

To evaluate the corrosion environment at the bottom of the reactor pressure vessel in a BWR and the effect of hydrogen water chemistry on the corrosion of materials in the region, measurements of the corrosion potential of Type-304 stainless steel and nickel base alloy were made in a laboratory test loop. The effect of water chemistry on the corrosion potential of nickel base alloy is found to be similar to the effect on Type-304 stainless steel. Flow analysis and precise evaluations of the corrosion potential of materials in the bottom region were implemented. Corrosion potentials throughout the region were evaluated from the flow analysis results. At the jet pump outlet and shroud support leg, a rather large amount of hydrogen had to be added to reduce the potential. Conversely, a small amount of hydrogen was enough in the case of the stub tube of the control rod drive guide tubing and the ICM housings located in the center of the bottom region. (author)

Effect of water flow rate and water chemistry on corrosion environment in reactor pressure vessel bottom of BWRs

International Nuclear Information System (INIS)

Ichikawa, Nagayoshi; Hemmi, Yukio; Takagi, Junichi; Urata, Hidehiro

1999-01-01

To evaluate the corrosion environment at the bottom of the reactor pressure vessel in a BWR and the effect of hydrogen water chemistry on the corrosion of materials in the region, measurements of the corrosion potential of Type-304 stainless steel and nickel base alloy were made in a laboratory test loop. The effect of water chemistry on the corrosion potential of nickel base alloy is found to be similar to the effect on Type-304 stainless steel. Flow analysis and precise evaluations of the corrosion potential of materials in the bottom region were implemented. Corrosion potentials throughout the region were evaluated from the flow analysis results. At the jet pump outlet and shroud support leg, a rather large amount of hydrogen had to be added to reduce the potential. Conversely, a small amount of hydrogen was enough in the case of the stub tube of the control rod drive guide tubing and the ICM housings located in the center of the bottom region. (author)

Home networking architecture for IPv6

OpenAIRE

Arkko, Jari; Weil, Jason; Troan, Ole; Brandt, Anders

2012-01-01

This text describes evolving networking technology within increasingly large residential home networks. The goal of this document is to define an architecture for IPv6-based home networking while describing the associated principles, considerations and requirements. The text briefly highlights the specific implications of the introduction of IPv6 for home networking, discusses the elements of the architecture, and suggests how standard IPv6 mechanisms and addressing can be employed in home ne...

Dynamics of Abusive IPv6 Networks

Science.gov (United States)

2014-09-01

39 List of References 43 Initial Distribution List 47 vii THIS PAGE INTENTIONALLY LEFT BLANK viii List of Figures Figure 1.1 Google User IPv6 Adoption...2 Figure 1.1: Google User IPv6 Adoption Statistics, from June 2014 [3] For example, as a result of expanding use of IPv6, it is hypothesized that a...excessive annoyance of poorly crafted advertising emails, they can sometimes contain attachments or links to scam offers, phishing attempts, or malicious

An IPv6 Multihomed Host for Outbound Traffic

Science.gov (United States)

Chen, Chin-Ling; Cao, Sheng-Lung

Though the technology of IPv6 network has become mature in recent years, it still takes long to dispose IPv6 in an all-round way in the internet. In this research, we have designed an IPv6 multihomed host architecture to connect both IPv6 network and 6to4 network. This paper describes a load balance mechanism that allows applications on multihomed devices to utilize the individual networks efficiently to transmit streams that could be part of a session. We experiment the relevant parameters in the IPv6 testbed environment to demonstrate its effectiveness.

Hydrogen Production by Steam Reforming of Liquefied Natural Gas (LNG) Over Nickel-Phosphorus-Alumina Xerogel Catalyst Prepared by a Carbon-Templating Epoxide-Driven Sol-Gel Method.

Science.gov (United States)

Bang, Yongju; Park, Seungwon; Han, Seung Ju; Yoo, Jaekyeong; Choi, Jung Ho; Kang, Tae Hun; Lee, Jinwon; Song, In Kyu

2016-05-01

A nickel-phosphorus-alumina xerogel catalyst was prepared by a carbon-templating epoxide-driven sol-gel method (denoted as CNPA catalyst), and it was applied to the hydrogen production by steam reforming of liquefied natural gas (LNG). For comparison, a nickel-phosphorus-alumina xerogel catalyst was also prepared by a similar method in the absence of carbon template (denoted as NPA catalyst). The effect of carbon template addition on the physicochemical properties and catalytic activities of the catalysts in the steam reforming of LNG was investigated. Both CNPA and NPA catalysts showed excellent textural properties with well-developed mesoporous structure. However, CNPA catalyst retained a more reducible nickel aluminate phase than NPA catalyst. XRD analysis of the reduced CNPA and NPA catalysts revealed that nickel sintering on the CNPA catalyst was suppressed compared to that on the NPA catalyst. From H2-TPD and CH4-TPD measurements of the reduced CNPA and NPA catalysts, it was also revealed that CNPA catalyst with large amount of hydrogen uptake and strong hydrogen-binding sites showed larger amount of methane adsorption than NPA catalyst. In the hydrogen production by steam reforming of LNG, CNPA catalyst with large methane adsorption capacity showed a better catalytic activity than NPA catalyst.

Modelling of hydrogen deflagration in a vented vessel

International Nuclear Information System (INIS)

Wang, L.L.; Wong, R.C.

1995-01-01

Hydrogen Deflagration inside closed and vented 2.3 m diameter vessels were simulated by using the GOTHIC lumped-parameter computer code. Different cell arrangements were used in the modelling. Other parameters such as flame speed and hydrogen concentration were studied. It was found that the calculated peak pressures for cases using the experimental measured burn durations were close to the pressures measured from the experiments. When the default flame speed was used, higher peak pressure was predicted by GOTHIC. This could be explained by the the fact that the default flame speed used in the GOTHIC burn model was based on the results of a large scale test with moderate turbulence level. However, the overall results of the pressure transients were comparable with the experimental data. In addition, time and spatial convergencies of the model were also studied. The peak pressure estimated by modelling the sphere as five or more spherical cells was shown to converge to within +/- 3 percent. (author). 8 refs., 6 tabs., 9 figs

Ultrasound augmented leaching of nickel sulfate in sulfuric acid and hydrogen peroxide media.

Science.gov (United States)

Li, Haoyu; Li, Shiwei; Peng, Jinhui; Srinivasakannan, Chandrasekar; Zhang, Libo; Yin, Shaohua

2018-01-01

A new method of preparation high purity nickel sulfate assisted by ultrasonic was studied. The process mechanism was analyzed by Inductively Coupled Plasma (ICP), X-ray diffraction (XRD), Scanning electron microscopy (SEM), and Energy dispersive X-ray spectrometry (EDS).The reaction mechanisms of oxidizing leaching and ultrasonic leaching were explored, respectively. Results showed that ultrasonic treatment peel off the oxide film on the surface of nickel. The leachate under strongly agitated, the yield rate of nickel sulfate was accelerate. And the reaction area was increased by the cavitation effect, the liquid-solid reaction was promoted, and the activation energy was reduced. The leaching rate of nickel reached 46.29% by conventional leaching, which takes about 5h. Under the same conditions, the ultrasonic leaching rate reached 40%, only half of the conventional leaching time. Concentration of leaching agent, reaction temperature, ultrasonic power, leaching time had significant effect on the enhancement of the leaching reaction with ultrasonic radiation. The leaching rate of 60.41% under the optimum experiment conditions as follows: sulfuric acid concentration 30%, hydrogen peroxide 10%, leaching temperature 333K, ultrasonic power 200W and leaching time 4h. The kinetic study of the system was investigated, and the reaction rates of conventional leaching and ultrasonic leaching were controlled by diffusion, and the apparent activation energies were 16.2kJ/mol and 11.83kJ/mol. Copyright © 2017. Published by Elsevier B.V.

Metal hydride electrode and nickel hydrogen storage battery; Suiso kyuzo gokin denkyoku oyobi nikkeru-suiso chikudenchi

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Y.; Tamagawa, H. [Shin-Kobe Electric Machinery Co. Ltd., Tokyo (Japan); Ikawa, A.; Muranaka, R. [Hitachi Ltd., Ibaraki (Japan). Hitachi Research Lab.

1996-04-16

Water soluble polymers such as cellulose derivatives and polyvinylalcohol have been used conventionally as binders for metal hydride electrode used for nickel-hydrogen storage batteries. The shortcomings of those binders, however, are low flexibility, and poor binding property for hydrogen absorbing alloy powder and the conductive supporting substrate. This invention relates to the use of ethylene-vinyl copolymer with less than -10{degree}C Tg as the binder for hydrogen absorbing alloy powder. It is desirable that the ethylene-vinylacetate copolymer is selected out of ethylene-vinyl acetate-acryl copolymer and ethylene-vinyl acetate-long chain vinyl ester copolymer, and that the addition is larger than 0.1wt% and less than 1wt% against the weight of hydrogen absorbing alloy in the electrode. The use of this binder results in strong binding of hydrogen absorbing alloy powder to the conductive supporting substrate, providing flexibility as well. 4 figs., 5 tabs.

Nivel de desempeño en redes IPv4 con respecto a redes IPv6 con MPLS y RSVP

Directory of Open Access Journals (Sweden)

Alexis Guevara Peña

2011-06-01

Full Text Available This paper contains relevant information of the state of art of traffic engineering, MPLS (Multiprotocol Lable Switching and RSVP (Resource Reservation Protocol, as a case study and the techniques used under the new version of IPV6, against IPV4 version. The paper is intended to serve as a framework for the study of Engineering Traffic Based on the new version of IPV6, specifically MPLS and RSVP, takinginto account relevant considerations necessary when making decisions regarding the stability of the Backbone remains the key to Internet service providers that have recently stabilized its IPv4 infrastructure.

Effect of nickel content on mechanical properties and fracture toughness of weld metal of WWER-1000 reactor vessel welded joints

Energy Technology Data Exchange (ETDEWEB)

Zubchenko, A.S.; Vasilchenko, G.S.; Starchenko, E.G.; Nosov, S.I

2004-08-01

Welding of WWER-1000 reactor vessel of steel 15X2HMPHIA is performed using the C{sub B}-12X2H2MAA wire and PHI-16 or PHI-16A flux. Nickel content in the weld metal usually lays within the limits 1.2-1.9%. The experimental data is shown on the weld metal with the nickel contents 1.28-2.45% after irradiation with fluence up to 260.10{sup 22}n/m{sup 2} at energy more than 0.5 MEV. The embrittlement was measured by shift of critical brittleness temperature. Has appeared, that the weld metal with the low nickel content is the least responsive to irradiation embrittlement. The mechanical properties and fracture toughness of the weld metal with the contents of a nickel less than 1.3% are studied. Specimens CT-1T are tested, the 'master-curve', and its confidence bounds with probability of destruction 5 and 95% is built. 'Master-curve' in the specified confidence interval is affirmed by CT-4T specimens test data. Is shown, that the mechanical properties and fracture toughness of the weld metal with the contents of nickel less than 1.3% satisfy the normative requirements.

Modelo para la integración de redes IPv4 – IPv6 basado en túneles

Directory of Open Access Journals (Sweden)

Danilo López

2010-12-01

Full Text Available The intention of this paper is to set up a general model in order to interconnect heterogeneous nets IPv4-IPv6, guarantying the integrity of the data, making use of transition techniques.

Sintering of nickel steam reforming catalysts

DEFF Research Database (Denmark)

Sehested, Jens; Larsen, Niels Wessel; Falsig, Hanne

2014-01-01

. In this paper, particle migration and coalescence in nickel steam reforming catalysts is studied. Density functional theory calculations indicate that Ni-OH dominate nickel transport at nickel surfaces in the presence of steam and hydrogen as Ni-OH has the lowest combined energies of formation and diffusion...

Destructive physical analysis of spaceflight qualified nickel-hydrogen battery cells

Energy Technology Data Exchange (ETDEWEB)

Coates, D.; Francisco, J.; Giertz, K.; Smith, R.; Nowlin, G. [Eagle-Picher Industries, Inc., Joplin, MO (United States). Advanced Systems Operation

1996-11-01

Nickel-hydrogen (NiH{sub 2}) batteries are extensively used in the aerospace industry as the power system of choice in earth-orbital spacecraft. The batteries are typically required to support a 10--15 year geosynchronous-earth-orbit (GEO) mission or thousands of charge/discharge cycles in low-earth-orbit (LEO). Reliability requirements for this application are extensive and include the routine destructive physical analysis (DPA) of sample flight production battery cells. Standard procedures have been developed over the past 15 years for the disassembly, handling and detailed analysis of the cell components. These include mechanical, thermal and impedance analysis, electrolyte concentration and distribution, gas management, corrosion, dye penetrant and radiographic inspection, and several chemical and electrochemical analytical procedures for the battery electrodes and separator materials. Electrolyte management is a critical issue in the electrolyte-starved NiH{sub 2} cell design and procedures have been developed to particularly address this aspect of the DPA analysis. Specific analytical procedures for cell components includes nickel electrode active material and sinter substrate corrosion analysis, scanning electron microscopy (SEM), energy dispersive x-ray analysis (EDX), cobalt ion, potassium-carbonate and anion analysis. Many of these procedures are also applicable to aerospace battery systems in general and to other alkaline rechargeable batteries.

Carbon-encapsulated nickel-iron nanoparticles supported on nickel foam as a catalyst electrode for urea electrolysis

International Nuclear Information System (INIS)

Wu, Mao-Sung; Jao, Chi-Yu; Chuang, Farn-Yih; Chen, Fang-Yi

2017-01-01

Highlights: • Electrochemical process can purify the urea-rich wastewater, producing hydrogen gas. • Carbon-encapsulated nickel iron nanoparticles (CE-NiFe) are prepared by pyrolysis. • An ultra-thin layer of CE-NiFe nanoparticles is attached to the 3D Ni foam. • CE-NiFe nanoparticles escalate both the urea electrolysis and hydrogen evolution. - Abstract: A cyanide-bridged bimetallic coordination polymer, nickel hexacyanoferrate, could be pyrolyzed to form carbon-encapsulated nickel-iron (CE-NiFe) nanoparticles. The formation of nitrogen-doped spherical carbon shell with ordered mesoporous structure prevented the structural damage of catalyst cores and allowed the migration and diffusion of electrolyte into the hollow carbon spheres. An ultra-thin layer of CE-NiFe nanoparticles could be tightly attached to the three-dimensional macroporous nickel foam (NF) by electrophoretic deposition. The CE-NiFe nanoparticles could lower the onset potential and increase the current density in anodic urea electrolysis and cathodic hydrogen production as compared with bare NF. Macroporous NF substrate was very useful for the urea electrolysis and hydrogen production, which allowed for fast transport of electron, electrolyte, and gas products. The superior electrocatalytic ability of CE-NiFe/NF electrode in urea oxidation and water reduction made it favorable for versatile applications such as water treatment, hydrogen generation, and fuel cells.

IPv6 Test Bed for Testing Aeronautical Applications

Science.gov (United States)

Wilkins, Ryan; Zernic, Michael; Dhas, Chris

2004-01-01

Aviation industries in United States and in Europe are undergoing a major paradigm shift in the introduction of new network technologies. In the US, NASA is also actively investigating the feasibility of IPv6 based networks for the aviation needs of the United States. In Europe, the Eurocontrol lead, Internet Protocol for Aviation Exchange (iPAX) Working Group is actively investigating the various ways of migrating the aviation authorities backbone infrastructure from X.25 based networks to an IPv6 based network. For the last 15 years, the global aviation community has pursued the development and implementation of an industry-specific set of communications standards known as the Aeronautical Telecommunications Network (ATN). These standards are now beginning to affect the emerging military Global Air Traffic Management (GATM) community as well as the commercial air transport community. Efforts are continuing to gain a full understanding of the differences and similarities between ATN and Internet architectures as related to Communications, Navigation, and Surveillance (CNS) infrastructure choices. This research paper describes the implementation of the IPv6 test bed at NASA GRC, and Computer Networks & Software, Inc. and these two test beds are interface to Eurocontrol over the IPv4 Internet. This research work looks into the possibility of providing QoS performance for Aviation application in an IPv6 network as is provided in an ATN based network. The test bed consists of three autonomous systems. The autonomous system represents CNS domain, NASA domain and a EUROCONTROL domain. The primary mode of connection between CNS IPv6 testbed and NASA and EUROCONTROL IPv6 testbed is initially a set of IPv6 over IPv4 tunnels. The aviation application under test (CPDLC) consists of two processes running on different IPv6 enabled machines.

A Literature Survey on Handoff for Mobile IPv6

OpenAIRE

Zongpu Jia; Gaolei Wang; Ran Zhao

2011-01-01

With the development of network technology, IPv6 will be widely used in the next generation Internet, IPv6 will be used in the next generation Internet, IPv6 could combine mobile networks and fixed wireless networks closely, which brings great convenience to people’s live. The handoff delay of Mobile IPv6 seriously affected the real-time communication service quality, therefore various improvement methods based on the basic Mobile IPv6 protocol are proposed. The working principle of Mob...

East/west steels for reactor pressure vessels

International Nuclear Information System (INIS)

Davies, M.; Kryukov, A.; Nikolaev, Y.; English, C.

1997-01-01

The report consist of three parts dealing with comparison of the irradiation behaviour of 'Eastern' and 'Western' steels, mechanisms of irradiation embrittlement and the role of compositional variations on the irradiation sensitivity of pressure vessels. Nickel, copper and phosphorus are the elements rendering the most essential influence on behaviour of pressure vessel steels under irradiation and subsequent thermal annealing. For WWER-440 reactor pressure vessel (RPV) steels in which nickel content does nor exceed 0.3% the main affecting factors are phosphorous and copper. For WWER-1000 RPV welds in which nickel content generally exceed 1.5% the role of nickel in radiation embrittlement is decisive. In 'Western' type steels main influencing elements are nickel and copper. The secondary role of phosphorus in radiation embrittlement of 'Western' steels is caused by lower relative content compared to 'Eastern' steels. The process of how copper, phosphorus and nickel contents affect the irradiation sensitivity of both types of steel seem to be similar. Some distinctions between the observed radiation effects is apparently caused by differences in the irradiation conditions and ratios of the contents of above mentioned elements in both types of steel. For 'Eastern' RPV steels the dependence of the recovery degree of irradiated steels due to postirradiation thermal annealing id obviously dependent on phosphorus contents and the influence of nickel contents on this process is detectable

Implantación de IPv6 : red, mecanismos de transición IPv4-IPv6, servicios de aplicación y migración de aplicaciones

OpenAIRE

Rodríguez Hervella, Juan Francisco

2003-01-01

El presente proyecto fin de carrera trata los aspectos más importantes de la gestión y migración de las redes IP hacia el nuevo protocolo de red IPv6 y pone gran énfasis en experiencias de implantación de los mismos. A lo largo de este proyecto se profundiza sobre los distintos mecanismos de transición IPv4/IPv6 existentes, concretamente se describen y se prueban (en entornos Linux y FreeBSD) los siguientes: .Túneles 6t04, automáticos, configurados. .Mecanismo DSTM, TRT, ISATAP, NAT-PT. Tambi...

Carbon-encapsulated nickel-cobalt alloys nanoparticles fabricated via new post-treatment strategy for hydrogen evolution in alkaline media

Science.gov (United States)

Guo, Hailing; Youliwasi, Nuerguli; Zhao, Lei; Chai, Yongming; Liu, Chenguang

2018-03-01

This paper addresses a new post-treatment strategy for the formation of carbon-encapsulated nickel-cobalt alloys nanoparticles, which is easily controlled the performance of target products via changing precursor composition, calcination conditions (e.g., temperature and atmosphere) and post-treatment condition. Glassy carbon electrode (GCE) modified by the as-obtained carbon-encapsulated mono- and bi-transition metal nanoparticles exhibit excellent electro-catalytic activity for hydrogen production in alkaline water electrolysis. Especially, Ni0.4Co0.6@N-Cs800-b catalyst prepared at 800 °C under an argon flow exhibited the best electrocatalytic performance towards HER. The high HER activity of the Ni0.4Co0.6@N-Cs800-b modified electrode is related to the appropriate nickel-cobalt metal ratio with high crystallinity, complete and homogeneous carbon layers outside of the nickel-cobalt with high conductivity and the synergistic effect of nickel-cobalt alloys that also accelerate electron transfer process.

Measuring and Comparing the Stability of Internet Paths over IPv4 & IPv6

OpenAIRE

Golkar, Forough

2014-01-01

Enormous Internet growth is an obvious trend nowadays while Internet protocol version 4 address space exhaustion led into the invention of Internet protocol version 6 and subsequently raised the transitioning challenges from one protocol to the other one. As the Internet protocol version 6 have not been around for a long time, thus there is a limitation knowledge in topology, routing change and performance of IPv6. Several studies are going on in order to getting the information about IPv6 wh...

Thermal modeling of nickel-hydrogen battery cells operating under transient orbital conditions

Science.gov (United States)

Schrage, Dean S.

1991-01-01

An analytical study of the thermal operating characteristics of nickel-hydrogen battery cells is presented. Combined finite-element and finite-difference techniques are employed to arrive at a computationally efficient composite thermal model representing a series-cell arrangement operating in conjunction with a radiately coupled baseplate and coldplate thermal bus. An aggressive, low-mass design approach indicates that thermal considerations can and should direct the design of the thermal bus arrangement. Special consideration is given to the potential for mixed conductive and convective processes across the hydrogen gap. Results of a compressible flow model are presented and indicate the transfer process is suitably represented by molecular conduction. A high-fidelity thermal model of the cell stack (and related components) indicates the presence of axial and radial temperature gradients. A detailed model of the thermal bus reveals the thermal interaction of individual cells and is imperative for assessing the intercell temperature gradients.

Study of Supported Nickel Catalysts Prepared by Aqueous Hydrazine Method. Hydrogenating Properties and Hydrogen Storage: Support Effect. Silver Additive Effect

International Nuclear Information System (INIS)

Wojcieszak, R.

2006-06-01

We have studied Ni or NiAg nano-particles obtained by the reduction of nickel salts (acetate or nitrate) by hydrazine and deposited by simple or EDTA-double impregnation on various supports (γ-Al 2 O 3 , amorphous or crystallized SiO 2 , Nb 2 O 5 , CeO 2 and carbon). Prepared catalysts were characterized by different methods (XRD, XPS, low temperature adsorption and desorption of N 2 , FTIR and FTIR-Pyridine, TEM, STEM, EDS, H 2 -TPR, H 2 -adsorption, H 2 -TPD, isopropanol decomposition) and tested in the gas phase hydrogenation of benzene or as carbon materials in the hydrogen storage at room temperature and high pressure. The catalysts prepared exhibited better dispersion and activity than classical catalysts. TOF's of NiAg/SiO 2 or Ni/carbon catalysts were similar to Pt catalysts in benzene hydrogenation. Differences in support acidity or preparation method and presence of Ag as metal additive play a crucial role in the chemical reduction of Ni by hydrazine and in the final properties of the materials. Ni/carbon catalysts could store significant amounts of hydrogen at room temperature and high pressure (0.53%/30 bars), probably through the hydrogen spillover effect. (author)

Palm H-FAME Production through Partially Hydrogenation using Nickel/Carbon Catalyst to Increase Oxidation Stability

Directory of Open Access Journals (Sweden)

Ramayeni Elsa

2018-01-01

Full Text Available One of the methods to improve the oxidation stability of palm biodiesel is through partially hydrogenation. The production using Nickel/Carbon catalyst to speed up the reaction rate. Product is called Palm H-FAME (Hydrogenated FAME. Partial hydrogenation breaks the unsaturated bond on FAME (Fatty Acid Methyl Ester, which is a key component of the determination of oxidative properties. Changes in FAME composition by partial hydrogenation are predicted to change the oxidation stability so it does not cause deposits that can damage the injection system of diesel engine, pump system, and storage tank. Partial hydrogenation is carried out under operating conditions of 120 °C and 6 bar with 100:1, 100:3, 100:5, 100:10 % wt catalyst in the stirred batch autoclave reactor. H-FAME synthesis with 100:5 % wt Ni/C catalyst can decrease the iodine number which is the empirical measure of the number of unsaturated bonds from 91.78 to 82.38 (g-I2/100 g with an increase of oxidation stability from 585 to 602 minutes.

Long life nickel electrodes for a nickel-hydrogen cell: Cycle life tests

Science.gov (United States)

Lim, H. S.; Verzwyvelt, S. A.

1985-01-01

In order to develop a long life nickel electrode for a Ni/H2 cell, the cycle life of nickel electrodes was tested in Ni/H2 boiler plate cells. A 19 test cell matrix was made of various nickel electrode designs including three levels each of plaque mechanical strength, median pore size of the plaque, and active material loading. Test cells were cycled to the end of their life (0.5v) in a 45 minute low Earth orbit cycle regime at 80% depth-of-discharge. It is shown that the active material loading level affects the cycle life the most with the optimum loading at 1.6 g/cc void. Mechanical strength does not affect the cycle life noticeably in the bend strength range of 400 to 700 psi. It is found that the best plaque is made of INCO nickel powder type 287 and has median pore size of 13 micron.

Antibody responses of Macaca fascicularis against a new inactivated polio vaccine derived from Sabin strains (sIPV) in DTaP-sIPV vaccine.

Science.gov (United States)

Sato, Y; Shiosaki, K; Goto, Y; Sonoda, K; Kino, Y

2013-05-01

Antibody responses of Macaca fascicularis against a new tetravalent vaccine composed of diphtheria toxoid, tetanus toxoid, acellular pertussis antigens, and inactivated poliovirus derived from Sabin strains (sIPV) was investigated to predict an optimal dose of sIPV in a new tetravalent vaccine (DTaP-sIPV) prior to conducting a dose-defined clinical study. Monkeys were inoculated with DTaP-sIPVs containing three different antigen units of sIPVs: Vaccine A (types 1:2:3 = 3:100:100 DU), Vaccine B (types 1:2:3 = 1.5:50:50 DU), and Vaccine C (types 1:2:3 = 0.75:25:25 DU). There was no difference in the average titers of neutralizing antibody against the attenuated or virulent polioviruses between Vaccines A and B. The average neutralizing antibody titers of Vaccine C tended to be lower than those of Vaccines A and B. The sIPV antigens did not affect the anti-diphtheria or anti-tetanus antibody titers of DTaP-sIPV. Furthermore, the average neutralizing antibody titers of Vaccine A against the attenuated and virulent polioviruses were comparable between M. fascicularis and humans. These results suggest that M. fascicularis may be a useful animal model for predicting the antibody responses to sIPVs in humans, and that it may be likely to reduce the amount of sIPVs contained in DTaP-sIPVs, even for humans. Copyright © 2013 The International Alliance for Biological Standardization. Published by Elsevier Ltd. All rights reserved.

Mobile video with mobile IPv6

CERN Document Server

Minoli, Daniel

2012-01-01

Increased reliance on mobile devices and streaming of video content are two of the most recent changes that have led those in the video distribution industry to be concerned about the shifting or erosion of traditional advertising revenues. Infrastructure providers also need to position themselves to take advantage of these trends. Mobile Video with Mobile IPv6provides an overview of the current mobile landscape, then delves specifically into the capabilities and operational details of IPv6. The book also addresses 3G and 4G services, the application of Mobile IPv6 to streaming and other mobil

Carbon formation on nickel and nickel-copper alloy catalysts

Energy Technology Data Exchange (ETDEWEB)

Alstrup, I.; Soerensen, O.; Rostrup-Nielsen, J.R. [Haldor Topsoe Research Labs., Lyngby (Denmark); Tavares, M.T.; Bernardo, C.A.

1998-05-01

Equilibrium, kinetic and morphological studies of carbon formation in CH{sub 4} + H{sub 2}, CO, and CO + H{sub 2} gases on silica supported nickel and nickel-copper catalysts are reviewed. The equilibrium deviates in all cases from graphite equilibrium and more so in CO + CO{sub 2} than in CH{sub 4} + H{sub 2}. A kinetic model based on information from surface science results with chemisorption of CH{sub 4} and possibly also the first dehydrogenation step as rate controlling describes carbon formation on nickel catalyst in CH{sub 4} + H{sub 2} well. The kinetics of carbon formation in CO and CO + H{sub 2} gases are in agreement with CO disproportionation as rate determining step. The presence of hydrogen influences strongly the chemisorption of CO. Carbon filaments are formed when hydrogen is present in the gas while encapsulating carbon dominates in pure CO. Small amounts of Cu alloying promotes while larger amounts (Cu : Ni {>=} 0.1) inhibits carbon formation and changes the morphology of the filaments (``octopus`` carbon formation). Adsorption induced nickel segregation changes the kinetics of the alloy catalysts at high carbon activities. Modifications suggested in some very recent papers on the basis of new results are also briefly discussed. (orig.) 31 refs.

ASSESSMENT OF THE POTENTIAL FOR HYDROGEN GENERATION DURING GROUTING OPERATIONS IN THE R AND P REACTOR VESSELS

Energy Technology Data Exchange (ETDEWEB)

Wiersma, B.

2010-05-24

The R- and P-reactor buildings were retired from service and are now being prepared for deactivation and decommissioning (D and D). D and D activities consist primarily of immobilizing contaminated components and structures in a grout-like formulation. Aluminum corrodes very rapidly when it comes in contact with the alkaline grout materials and as a result produces hydrogen gas. To address this potential deflagration/explosion hazard, the Materials Science and Technology Directorate (MS and T) of the Savannah River National Laboratory (SRNL) has been requested to review and evaluate existing experimental and analytical studies of this issue to determine if any process constraints on the chemistry of the fill material and the fill operation are necessary. Various options exist for the type of grout material that may be used for D and D of the reactor vessels. The grout formulation options include ceramicrete (pH 6-8), low pH portland cement + silica fume grout (pH 10.4), or Portland cement groupt (pH 12.5). The assessment concluded that either ceramicrete or the silica fume grout may be used to safely grout the P-reactor vessel. The risk of accumulation of a flammable mixture of hydrogen between the grout-air interface and the top of the reactor is very low. Portland cement grout, on the other hand, for the same range of process parameters does not provide a margin of safety against the accumulation of flammable gas in the reactor vessel during grouting operations in the P-reactor vessel. It is recommended that this grout not be utilized for this task. The R-reactor vessel cotnains significantly less aluminum based on current facility process knowledge, surface observations, and drawings. Therefore, a Portland cement grout may be considered for grouting operations as well as the other grout formulations. For example, if the grout fill rate is less than 1 inch/min and the grout temperature is maintained at 70 C or less, the risk of hydrogen accumulation during fill

Sensitivity analyses on in-vessel hydrogen generation for KNGR

International Nuclear Information System (INIS)

Kim, See Darl; Park, S.Y.; Park, S.H.; Park, J.H.

2001-03-01

Sensitivity analyses for the in-vessel hydrogen generation, using the MELCOR program, are described in this report for the Korean Next Generation Reactor. The typical accident sequences of a station blackout and a large LOCA scenario are selected. A lower head failure model, a Zircaloy oxidation reaction model and a B 4 C reaction model are considered for the sensitivity parameters. As for the base case, 1273.15K for a failure temperature of the penetrations or the lower head, an Urbanic-Heidrich correlation for the Zircaloy oxidation reaction model and the B 4 C reaction model are used. Case 1 used 1650K as the failure temperature for the penetrations and Case 2 considered creep rupture instead of penetration failure. Case 3 used a MATPRO-EG and G correlation for the Zircaloy oxidation reaction model and Case 4 turned off the B 4 C reaction model. The results of the studies are summarized below : (1) When the penetration failure temperature is higher, or the creep rupture failure model is considered, the amount of hydrogen increases for two sequences. (2) When the MATPRO-EG and G correlation for a Zircaloy oxidation reaction is considered, the amount of hydrogen is less than the Urbanic-Heidrich correlation (Base case) for both scenarios. (3) When the B 4 C reaction model turns off, the amount of hydrogen decreases for two sequences

First-in-human safety and immunogenicity investigations of three adjuvanted reduced dose inactivated poliovirus vaccines (IPV-Al SSI) compared to full dose IPV Vaccine SSI when given as a booster vaccination to adolescents with a history of IPV vaccination at 3, 5, 12months and 5years of age.

Science.gov (United States)

Lindgren, Line M; Tingskov, Pernille N; Justesen, Annette H; Nedergaard, Bettina S; Olsen, Klaus J; Andreasen, Lars V; Kromann, Ingrid; Sørensen, Charlotte; Dietrich, Jes; Thierry-Carstensen, Birgit

2017-01-23

There is a demand of affordable IPV in the World. Statens Serum Institut (SSI) has developed three reduced dose IPV formulations adsorbed to aluminium hydroxide; 1/3 IPV-Al, 1/5 IPV-Al and 1/10 IPV-Al SSI, and now report the results of the first investigations in humans. 240 Danish adolescents, aged 10-15years, and childhood vaccinated with IPV were booster vaccinated with 1/3 IPV-Al, 1/5 IPV-Al, 1/10 IPV-Al or IPV Vaccine SSI. The booster effects (GMTRs) of the three IPV-Al SSI were compared to IPV Vaccine SSI, and evaluated for non-inferiority. The pre-vaccination GMTs were similar across the groups; 926 (type 1), 969 (type 2) and 846 (type 3) in the total trial population. The GMTRs by poliovirus type and IPV formulation were: Type 1: 17.0 (1/3 IPV-Al), 13.0 (1/5 IPV-Al), 7.1 (1/10 IPV-Al) and 42.2 (IPV Vaccine SSI). Type 2: 12.5 (1/3 IPV-Al), 13.1 (1/5 IPV-Al), 7.6 (1/10 IPV-Al) and 47.8 (IPV Vaccine SSI). Type 3: 14.5 (1/3 IPV-Al), 16.2 (1/5 IPV-Al), 8.9 (1/10 IPV-Al) and 62.4 (IPV Vaccine SSI) Thus, the three IPV-Al formulations were highly immunogenic, but inferior to IPV Vaccine SSI, in this booster vaccination trial. No SAE and no AE of severe intensity occurred. 59.2% of the subjects reported at least one AE. Injection site pain was the most frequent AE in all groups; from 24.6% to 43.3%. Injection site redness and swelling frequencies were<5% in most and<10% in all groups. The most frequent systemic AEs were fatigue (from 8.2% to 15.0%) and headache (from 15.0% to 28.3%). Most AEs were of mild intensity. In conclusion, the three IPV-Al SSI were safe in adolescents and the booster effects were satisfactory. ClinicalTrials.gov registration number: NCT02280447. Copyright © 2016. Published by Elsevier Ltd.

Implementation of IPv6 at the PřF JU

OpenAIRE

JOUDAL, Jakub

2011-01-01

Aspects of IPv6 implementation. Is the current network structure capable of deploying IPv6 JU? What would this change mean? What will be the financial costs of transition? The advantages of IPv6 in terms of high schools.

Intimate partner violence: IPV in the LGBT community.

Science.gov (United States)

Chen, Ping-Hsin; Jacobs, Abbie; Rovi, Susan L D

2013-09-01

Nationally, the rates of intimate partner violence (IPV) among lesbian, gay, bisexual, or transgender (LGBT) individuals are similar to or greater than rates for heterosexuals. Many have experienced psychological and physical abuse as sexual minorities, making it difficult for them to seek help for IPV. Physician behavior, such as not assuming that all patients are heterosexual, being nonjudgmental, and using inclusive language, can empower LGBT patients to disclose IPV. Also, physicians should ascertain the degree to which the patient is out. The threat of being outed can be an aspect of the power and control exerted by an abusive partner and a significant barrier to seeking help. Physicians should screen for IPV and intervene in a similar manner with LGBT and non-LGBT patients, but they should be aware of potential limitations in resources for LGBT patients, such as shelters. As sexual minorities experiencing IPV, LGBT individuals are at greater risk of depression and substance abuse than are non-LGBT individuals. Minority stress, resulting from stigmatization and discrimination, can be exacerbated by IPV. Physicians should learn about legal issues for LGBT individuals and the availability of community or advocacy programs for LGBT perpetrators or victims of IPV. Written permission from the American Academy of Family Physicians is required for reproduction of this material in whole or in part in any form or medium.

Analisis Kesiapan Penyelenggara Jaringan Internet di Indonesia dalam Migrasi ke IPv6

Directory of Open Access Journals (Sweden)

Riza Azmi

2012-06-01

Full Text Available Internet Protocol merupakan sumberdaya pengalamatan jaringan yang sifatnya terbatas. Sejak dikembangkankan konsep TCP/IP, sumberdaya pengalamatan jaringan dan internet berbasiskan pada Internet Protokol versi 4 (IPv4 yang memiliki 4 miliar alamat unik. Data dari potaroo.net pada 18 maret 2011, diperkirakan alokasi IPv4 berakhir pada bulan May 2011. Dalam menghadapi keterbatasan IPv4 tersebut, dibuatlah konsep pengalamatan baru IPv6 yang memiliki jumlah alamat 6,5 x 1038 alamat unik. Di Indonesia sendiri dalam rangka mengantisipasi habisnya penggunaan IPv4 tersebut, stakeholder internet di Indonesia yang dikomandoi oleh Kementerian Komunikasi dan Informatika cq. Ditjen Postel membentuk Indonesia IPv6 Task Force (ID-IPv6TF. ID-IPv6TF merumuskan peta jalan / roadmap migrasi ke IPv6 versi 2 yang berakhir pada 2012. Studi ini melakukan evaluasi formatif sejauhmana kesiapan migrasi dari IPv4 ke IPv6 di Indonesia pada tingkat Penyelenggara Jaringan Internet  dengan melihat dari dimensi kesiapan aplikasi, strategi migrasi dan kesiapan infrastruktur. Kesiapan migrasi tersebut dikategorkan menjadi 5 level yaitu IPv6 Agnostic, IPv6 Aware,. Hasil studi menunjukkan bahwa Indonesia berada pada level IPv6 Savvy dengan distribusi level yang beragam.

High temperature cathodic charging of hydrogen in zirconium alloys and iron and nickel base alloys

International Nuclear Information System (INIS)

John, J.T.; De, P.K.; Gadiyar, H.S.

1990-01-01

These investigations lead to the development of a new technique for charging hydrogen into metals and alloys. In this technique a mixture of sulfates and bisulfates of sodium and potassium is kept saturated with water at 250-300degC in an open pyrex glass beaker and electrolysed using platinum anode and the material to be charged as the cathode. Most of the studies were carried out on Zr alloys. It is shown that because of the high hydrogen flux available at the surface and the high diffusivity of hydrogen in metals at these temperatures the materials pick up hydrogen faster and more uniformly than the conventional electrolytic charging at room temperature and high temperature autoclaving in LiOH solutions. Chemical analysis, metallographic examination and XRD studies confirm this. This technique has been used to charge hydrogen into many iron and nickel base austentic alloys, which are very resistant to hydrogen pick up and to H-embrittlement. Since this involved a novel method of electrolysing water, the hydrogen/deuterium isotopic ratio has been studied. At this temperatures the D/H ratio in the evolved hydrogen gas was found to be closer to the value in the liquid water, which means a smaller separation factor. This confirm the earlier observation that separation factor decreases with increase of temperature. (author). 16 refs., 21 fi gs., 6 tabs

A magnetic investigation of phase transitions for metal-hydrogen systems based on nickel by means of computer-aided data acquisition

International Nuclear Information System (INIS)

Martin, W.E.

1986-01-01

In the present thesis the magnetic behaviour of Nickel-based metal-hydrogen systems is investigated in relation to its background in metal physics, in order to get information on the formation and the decomposition of metal-hydrogen phases. The magnetic investigations are performed at the systems Ni-Cu-H and Ni-Cr-H with Cu up to 40 at% and Cr up to 7 at%. The differential susceptibility is measured during hydration and decomposition of hydrides and the connection between magnetic moment and hydrogen concentration is discussed. (BHO)

An overview of advanced high-strength nickel-base alloys for LWR applications

International Nuclear Information System (INIS)

Prybylowski, J.; Ballinger, R.G.

1989-01-01

This paper reviews our current understanding of the behavior of high strength nickel base alloys used in light water reactor (LWR) applications. Emphasis is placed on understanding the fundamental mechanisms controlling crack propagation in these environments. To provide a foundation for this survey, general mechanisms of stress corrosion cracking and hydrogen embrittlement are first reviewed. The behavior of high strength nickel base alloys in LWR environments, as well as in other relevant environments is then reviewed. Suggested mechanisms of crack propagation are discussed. Alternate alloys and microstructural modifications that may result in improved behavior are presented. It is now clear that, at temperatures near 100C, alloy X-750, the predominant high strength nickel base alloy used today in LWR applications, is susceptible to hydrogen embrittlement. A review of published data from hydrogen embrittlement studies of nickel base superalloys during electrolytic charging and in hydrogen sulfide/brine solutions suggests that other nickel base superalloys are available possessing resistance to hydrogen embrittlement superior to that of alloy X-750. Available results of tests in gaseous hydrogen suggest that reduced grain boundary precipitation and a fine distribution of intragranular precipitates that act as irreversible hydrogen traps is the optimum microstructure for hydrogen embrittlement resistance. 42 refs., 2 figs., 5 tabs

Dry Reforming of Methane Using a Nickel Membrane Reactor

Directory of Open Access Journals (Sweden)

Jonas M. Leimert

2017-12-01

Full Text Available Dry reforming is a very interesting process for synthesis gas generation from CH 4 and CO 2 but suffers from low hydrogen yields due to the reverse water–gas shift reaction (WGS. For this reason, membranes are often used for hydrogen separation, which in turn leads to coke formation at the process temperatures suitable for the membranes. To avoid these problems, this work shows the possibility of using nickel self-supported membranes for hydrogen separation at a temperature of 800 ∘ C. The higher temperature effectively suppresses coke formation. The paper features the analysis of the dry reforming reaction in a nickel membrane reactor without additional catalyst. The measurement campaign targeted coke formation and conversion of the methane feedstock. The nickel approximately 50% without hydrogen separation. The hydrogen removal led to an increase in methane conversion to 60–90%.

Deployment of IPv6-only CPU resources at WLCG sites

Science.gov (United States)

Babik, M.; Chudoba, J.; Dewhurst, A.; Finnern, T.; Froy, T.; Grigoras, C.; Hafeez, K.; Hoeft, B.; Idiculla, T.; Kelsey, D. P.; López Muñoz, F.; Martelli, E.; Nandakumar, R.; Ohrenberg, K.; Prelz, F.; Rand, D.; Sciabà, A.; Tigerstedt, U.; Traynor, D.

2017-10-01

The fraction of Internet traffic carried over IPv6 continues to grow rapidly. IPv6 support from network hardware vendors and carriers is pervasive and becoming mature. A network infrastructure upgrade often offers sites an excellent window of opportunity to configure and enable IPv6. There is a significant overhead when setting up and maintaining dual-stack machines, so where possible sites would like to upgrade their services directly to IPv6 only. In doing so, they are also expediting the transition process towards its desired completion. While the LHC experiments accept there is a need to move to IPv6, it is currently not directly affecting their work. Sites are unwilling to upgrade if they will be unable to run LHC experiment workflows. This has resulted in a very slow uptake of IPv6 from WLCG sites. For several years the HEPiX IPv6 Working Group has been testing a range of WLCG services to ensure they are IPv6 compliant. Several sites are now running many of their services as dual-stack. The working group, driven by the requirements of the LHC VOs to be able to use IPv6-only opportunistic resources, continues to encourage wider deployment of dual-stack services to make the use of such IPv6-only clients viable. This paper presents the working group’s plan and progress so far to allow sites to deploy IPv6-only CPU resources. This includes making experiment central services dual-stack as well as a number of storage services. The monitoring, accounting and information services that are used by jobs also need to be upgraded. Finally the VO testing that has taken place on hosts connected via IPv6-only is reported.

Hydrodynamic model of hydrogen-flame propagation in reactor vessels

International Nuclear Information System (INIS)

Baer, M.R.; Ratzel, A.C.

1982-01-01

A hydrodynamic model for hydrogen flame propagation in reactor geometries is presented. This model is consistent with the theory of slow combustion in which the gasdynamic field equations are treated in the limit of small Mach numbers. To the lowest order, pressure is spatially uniform. The flame is treated as a density and entropy discontinuity which propagates at prescribed burning velocities, corresponding to laminar or turbulent flames. Radiation cooling of the burned combustion gases and possible preheating of the unburned gases during propagation of the flame is included using a molecular gas-band thermal radiation model. Application of this model has been developed for 1-D variable area flame propagation. Multidimensional effects induced by hydrodynamics and buoyancy are introduced as a correction to the burn velocity (which reflects a modification of planar flame surface to a distorted surface) using experimentally measured pressure-rise time data for hydrogen/air deflagrations in cylindrical vessels

Radiation embrittlement of WWER-1000 reactor vessel steels

International Nuclear Information System (INIS)

Nikolaeva, A.V.; Nikolaev, Yu.A.; Kevorkyan, Yu.R.

2001-01-01

Results obtained on the blank samples of materials of the WWER-1000 vessels irradiated by low density neutron flux are discussed. Chemical composition of the materials is characterized by the low content of the impurities (copper and phosphorus) and high content of nickel. Dependence of the radiation embrittlement of the WWER-1000 vessel materials on metallurgic variables and damage dose is treated. The research showed that nickel largely enhanced the radiation embrittlement. New dependences for determination of the radiation embrittlement real rate of the WWER-1000 vessel materials and its conservative estimation were developed [ru

Development of nickel membranes deposited on ceramic materials by electroless plating: studies of the hydrogen perm-selectivity properties at elevated temperatures

International Nuclear Information System (INIS)

Amer, J.

2008-09-01

The main objective of this work was to synthesize nickel based membranes by electroless plating on materials such as alumina-α, alumina-γ and zirconia with various textures and to determine their hydrogen perm-selectivity at high temperatures. The synthesis of metal films of high purity (≥ 99% mass Ni) resulting from the choice of hydrazine with its dual role of reducing and complexing agent has revealed that the diameter of pores on the surface support has an impact on the quality of metal adherence. The various contributions of hydrogen transport through these composite membranes at low temperatures (Knudsen and surface diffusion) and at high temperatures (Knudsen and activated diffusion) was established. At its implementation in a membrane reactor (reaction of propane dehydrogenation), the layer of nickel showed a very good resistance to coking. (author)

Influence of metallurgical heterogeneities on the mechanisms of hydrogen diffusion and trapping of in nickel

International Nuclear Information System (INIS)

Oudriss, Abdelali

2012-01-01

A thorough investigation on the influence of several metallurgical defects on the hydrogen diffusion and trapping was conducted on nickel. This work was conducted towards two scientific orientations. A first approach was to assess the impact of intrinsic defects, especially grain boundaries and geometrically necessary dislocations on the hydrogen transport and segregation mechanisms. Combining microstructural characterizations with electrochemical permeation tests and thermal desorption spectroscopy, it has established that the grain boundaries with ordered structure called 'special grain boundaries' are preferential areas for hydrogen segregation. On the other hand, a second category of grain boundaries called 'general' or 'random' with high free volume and disordered structure are promoters for hydrogen diffusion, and they represent the main sources of the phenomena short circuit diffusion reported in the face-centered cubic materials. The second approach of this work consisted in the study of the interaction of hydrogen with the plastic deformation heterogeneities. The electrochemical permeation tests performed on microstructures obtained by deformation showed that for the traction monotonous, the equiaxed cells and walls of dislocations are the potential traps for hydrogen and they slow its transport, this latter is mainly provided by the interstitial diffusion mechanism. In addition, for fatigue microstructure, rapid diffusivity of hydrogen was recorded, and suggesting that a phenomenon similar to short-circuit diffusion is involved in the transport of hydrogen. On two approaches, the results suggest a contribution of hydrogen in the formation of vacancies. (author) [fr

IPv6 Addressing Proxy: Mapping Native Addressing from Legacy Technologies and Devices to the Internet of Things (IPv6)

OpenAIRE

Jara, Antonio J.; Moreno-Sanchez, Pedro; Skarmeta, Antonio F.; Varakliotis, Socrates; Kirstein, Peter

2013-01-01

Sensors utilize a large number of heterogeneous technologies for a varied set of application environments. The sheer number of devices involved requires that this Internet be the Future Internet, with a core network based on IPv6 and a higher scalability in order to be able to address all the devices, sensors and things located around us. This capability to connect through IPv6 devices, sensors and things is what is defining the so-called Internet of Things (IoT). IPv6 provides addressing spa...

Improved rapidly-quenched hydrogen-absorbing alloys for development of improved-capacity nickel metal hydride batteries

Science.gov (United States)

Ise, Tadashi; Hamamatsu, Takeo; Imoto, Teruhiko; Nogami, Mitsuzo; Nakahori, Shinsuke

The effects of annealing a rapidly-quenched hydrogen-absorbing alloy with a stoichiometric ratio of 4.76 were investigated concerning its hydrogen-absorbing properties, crystal structure and electrochemical characteristics. Annealing at 1073 K homogenized the alloy microstructure and flattened its plateau slope in the P-C isotherms. However, annealing at 1273 K segregated a second phase rich in rare earth elements, increased the hydrogen-absorbing pressure and decreased the hydrogen-absorbing capacity. As the number of charge-discharge cycles increases, the particle size distribution of the rapidly-quenched alloy became broad due to partial pulverization. However, particle size distribution of the rapidly-quenched, annealed, alloy was sharp, since the annealing homogenized the microstructure, thereby improving the cycle characteristics. A high-capacity rectangular nickel metal hydride battery using a rapidly-quenched, annealed, surface-treated alloy for the negative electrode and an active material coated with cobalt compound containing sodium for the positive electrode was developed. The capacity of the resulting battery was 30% greater than that of a conventional battery.

Water level measurement system in reactor pressure vessel of BWR and hydrogen concentration monitoring system for severe accident

International Nuclear Information System (INIS)

Kuroda, Hidehiko; Okazaki, Koki; Shiraishi, Fujio; Kenjyo, Hiroaki; Isoda, Koichiro

2013-01-01

TEPCO's Fukushima Daiichi Nuclear Power Station Accident caused severe accident to lose functions of many instrumentation systems. As a result, many important plant parameters couldn't be monitored. In order to monitor plant parameters in the case of severe accident, new instrumentation systems available in the severe conditions are being developed. Water level in reactor pressure vessel and hydrogen concentration in primary containment vessel are one of the most important parameters. Performance test results about water level measurement sensor and hydrogen sensor in severe environmental conditions are described. (author)

Embrittlement and annealing of reactor pressure vessel steels: comparison of BR3 surveillance and vessel plates to the surrogate plates representative of the Yankee Rowe vessel

International Nuclear Information System (INIS)

Fabry, A.; Chaouadi, T.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rossinski, S.T.; Carter, R.G.

1996-07-01

The sister pressure vessels at the BR3 and Rowe Yankee PWR plants were operated at a lower-than-usual temperature (260 degrees Celsius) and their plates were austenitized at higher-than-usual temperature (970 degrees Celsius). A heat tratemement leading to a coarser microstructure than typical for the fine grain plates that are considered in development of USNRC Regulatory guide 1.99. This material displayed outlier behaviour charackterized by a 41J CVN-shift significantly larger than predicted by Regulatory Guide 1.99. Because lower radiation temperature and nickell alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rowe plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements enbodied in the PTS screening criterion. This paper compares three complementary studies undertaken to clarify these uncertainties: 1) the accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63% (A533-B) and YA9, 0.19% (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively, 2) the BR3 surveillance and vessel testing program: this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, ANCL was trepanned in early 1995, 3) the accelerated irradiations in the Belgian BR2 test reactor of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is shown that the PTS screening criterion was never attained by the BR3 and Rowe plates, and that the BR3 vessel anneal was neither necessary nor sufficient. Finally, the sensitivity of embrittlement, annealing and post-annealing reembrittlement to irradiation

Embrittlement and annealing of reactor pressure vessel steels: comparison of BR3 surveillance and vessel plates to the surrogate plates representative of the Yankee Rowe vessel

Energy Technology Data Exchange (ETDEWEB)

Fabry, A.; Chaouadi, T.; Puzzolante, J.L.; Van de Velde, J. [Centre de l``Etude de l``Energie Nucleaire, Mol (Belgium); Biemiller, E.C. [Yankee Atomic Electric Company, Bolton (United States); Rossinski, S.T.; Carter, R.G. [Electric Power Research Institute, Charlotte (United States)

1996-07-01

The sister pressure vessels at the BR3 and Rowe Yankee PWR plants were operated at a lower-than-usual temperature (260 degrees Celsius) and their plates were austenitized at higher-than-usual temperature (970 degrees Celsius). A heat tratemement leading to a coarser microstructure than typical for the fine grain plates that are considered in development of USNRC Regulatory guide 1.99. This material displayed outlier behaviour charackterized by a 41J CVN-shift significantly larger than predicted by Regulatory Guide 1.99. Because lower radiation temperature and nickell alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rowe plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements enbodied in the PTS screening criterion. This paper compares three complementary studies undertaken to clarify these uncertainties: 1) the accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63% (A533-B) and YA9, 0.19% (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively, 2) the BR3 surveillance and vessel testing program: this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, ANCL was trepanned in early 1995, 3) the accelerated irradiations in the Belgian BR2 test reactor of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is shown that the PTS screening criterion was never attained by the BR3 and Rowe plates, and that the BR3 vessel anneal was neither necessary nor sufficient. Finally, the sensitivity of embrittlement, annealing and post-annealing reembrittlement to irradiation

Mobile Multicast in Hierarchical Proxy Mobile IPV6

Science.gov (United States)

Hafizah Mohd Aman, Azana; Hashim, Aisha Hassan A.; Mustafa, Amin; Abdullah, Khaizuran

2013-12-01

Mobile Internet Protocol Version 6 (MIPv6) environments have been developing very rapidly. Many challenges arise with the fast progress of MIPv6 technologies and its environment. Therefore the importance of improving the existing architecture and operations increases. One of the many challenges which need to be addressed is the need for performance improvement to support mobile multicast. Numerous approaches have been proposed to improve mobile multicast performance. This includes Context Transfer Protocol (CXTP), Hierarchical Mobile IPv6 (HMIPv6), Fast Mobile IPv6 (FMIPv6) and Proxy Mobile IPv6 (PMIPv6). This document describes multicast context transfer in hierarchical proxy mobile IPv6 (H-PMIPv6) to provide better multicasting performance in PMIPv6 domain.

Inactivated polio vaccine development for technology transfer using attenuated Sabin poliovirus strains to shift from Salk-IPV to Sabin-IPV.

Science.gov (United States)

Bakker, Wilfried A M; Thomassen, Yvonne E; van't Oever, Aart G; Westdijk, Janny; van Oijen, Monique G C T; Sundermann, Lars C; van't Veld, Peter; Sleeman, Eelco; van Nimwegen, Fred W; Hamidi, Ahd; Kersten, Gideon F A; van den Heuvel, Nico; Hendriks, Jan T; van der Pol, Leo A

2011-09-22

Industrial-scale inactivated polio vaccine (IPV) production dates back to the 1960s when at the Rijks Instituut voor de Volksgezondheid (RIV) in Bilthoven a process was developed based on micro-carrier technology and primary monkey kidney cells. This technology was freely shared with several pharmaceutical companies and institutes worldwide. In this contribution, the history of one of the first cell-culture based large-scale biological production processes is summarized. Also, recent developments and the anticipated upcoming shift from regular IPV to Sabin-IPV are presented. Responding to a call by the World Health Organization (WHO) for new polio vaccines, the development of Sabin-IPV was continued, after demonstrating proof of principle in the 1990s, at the Netherlands Vaccine Institute (NVI). Development of Sabin-IPV plays an important role in the WHO polio eradication strategy as biocontainment will be critical in the post-OPV cessation period. The use of attenuated Sabin strains instead of wild-type Salk polio strains will provide additional safety during vaccine production. Initially, the Sabin-IPV production process will be based on the scale-down model of the current, and well-established, Salk-IPV process. In parallel to clinical trial material production, process development, optimization and formulation research is being carried out to further optimize the process and reduce cost per dose. Also, results will be shown from large-scale (to prepare for future technology transfer) generation of Master- and Working virus seedlots, and clinical trial material (for phase I studies) production. Finally, the planned technology transfer to vaccine manufacturers in low and middle-income countries is discussed. Copyright © 2011 Elsevier Ltd. All rights reserved.

So you've got IPv6 address space. Can you defend it?

OpenAIRE

Sande, Mikal

2014-01-01

Internet Protocol version 6 (IPv6) is the successor of Internet Protocol version 4 (IPv4). IPv6 will become the next standard networking protocol on the Internet. It brings with it a great increase in address space, changes to network operations, and new network security concerns. In this thesis we examine IPv6 from a security perspective. The security of IPv6 is important to all protocols that use IPv6 on the Internet. The goal of this thesis is to introduce the reader to existing IPv6 secur...

Discovery of IPV6 Router Interface Addresses via Heuristic Methods

Science.gov (United States)

2015-09-01

NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS DISCOVERY OF IPV6 ROUTER INTERFACE ADDRESSES VIA HEURISTIC METHODS by Matthew D. Gray September...AND SUBTITLE DISCOVERY OF IPV6 ROUTER INTERFACE ADDRESSES VIA HEURISTIC METHODS 5. FUNDING NUMBERS CNS-1111445 6. AUTHOR(S) Matthew D. Gray 7...Internet Assigned Numbers Authority, there is continued pressure for widespread IPv6 adoption. Because the IPv6 address space is orders of magnitude

Simulasi Penggunaan Ipv6 Pada PD. Pumas Jaya Menggunakan Metode Manual Tunneling

Directory of Open Access Journals (Sweden)

Elidjen Elidjen

2010-12-01

Full Text Available Internet usage trends with IPv4 addresses that only have 32-bit addresses could no longer cope with the large allocation of the required addresses. Internet Engineering Task Force (IETF has issued a new standard of Internet protocol called IPv6 to anticipate this problem. PD. Pumas Jaya, which started in 1996 in the field of marine products in particular marinated seafood, such as salted fish, rebon shrimp, cuttlefish, anchovies and other marine products to anticipate the need for this in its network. However, IPv6 can not simply be used to replace IPv4 as the existing network infrastructure with IPv4. This research discussed IPv6 simulation tunneling with manual methods so that an IPv6 site can communicate with other IPv6 site even if separated by an infrastructure that supports only IPv4. 

Hydrogen evolution reaction at Ru-modified nickel-coated carbon fibre in 0.1 M NaOH

Directory of Open Access Journals (Sweden)

Pierożyński Bogusław

2015-03-01

Full Text Available The electrochemical activity towards hydrogen evolution reaction (HER was studied on commercially available (Toho-Tenax and Ru-modified nickel-coated carbon fibre (NiCCF materials. Quality and extent of Ru electrodeposition on NiCCF tows were examined by means of scanning electron microscopy (SEM. Kinetics of the hydrogen evolution reaction were investigated at room temperature, as well as over the temperature range: 20-50°C in 0.1 M NaOH solution for the cathodic overpotential range: -100 to -300 mV vs. RHE. Corresponding values of charge-transfer resistance, exchange current-density for the HER and other electrochemical parameters for the examined fibre tow composites were recorded.

IPv6: The Next Generation Internet Protocol

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 8; Issue 3. IPv6: The Next Generation Internet Protocol - IPv4 and its Shortcomings. Harsha Srinath. General Article Volume 8 Issue 3 March 2003 pp 33-41. Fulltext. Click here to view fulltext PDF. Permanent link:

IPv6: The Next Generation Internet Protocol

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 8; Issue 4. IPv6: The Next Generation Internet Protocol - New Features in IPv6. Harsha Srinath. General Article Volume 8 Issue 4 April 2003 pp 8-16. Fulltext. Click here to view fulltext PDF. Permanent link:

Contribution to the study of the electrodeposition of iron-nickel alloys; Contribution a l'etude du depot electrolytique des alliages fer-nickel

Energy Technology Data Exchange (ETDEWEB)

Valignat, J [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1967-12-01

Using a coulometric technique based upon the anodic intentiostatic dissolution, we studied the potentiostatic, deposition of nickel, iron and nickel iron alloys. We have shown that the minimum of the curve I = f (t) (deposition current versus time) is probably due to the transitory blocking of the surface by hydrogen and that the syn-crystallisation of nickel and iron is responsible for the anomalous co-deposition of these two elements. (author) [French] En employant une methode coulometrique par dissolution anodique intensipstatique, nous avons etudie le depot potentiostatique du nickel, du fer et des alliages fer-nickel. Nous avons pu montrer que le minimum de la courbe I = f (t) enregistree au cours du depot est du probablement au blocage momentane de la surface par l'hydrogene et que la syncristallisation du fer et du nickel est responsable de l'anomalie du depot simultane de ces deux elements. (auteur)

Inkubasi Implementasi Ipv6 di Lingkungan PT Telekomunikasi Indonesia Tbk

Directory of Open Access Journals (Sweden)

Lunel Candra

2013-12-01

ABSTRACT As a network and information service provider in Indonesia, PT Telekomunikasi Indonesia (Telkom is facing a number of problems of exhausted IP addresses, which is also being faced by global telecommunications world. IP addresses widely used todays, i.e. IPv4, have a limitation in terms of number and will be out soon. However, there are some solutions that can be done by telecom operators including implementation of NAT (Network Address Translation 444, dual stack IPv4 and IPv6, tunneling, and native IPv6. Each of the solutions mentioned above have advantages and disadvantages, but the target native IPv6 as main target seems to be the only feasible solution to be addressed by IT industry players, including Telkom. Telkom RDC as the unit mainly focusing in the research of IT technology has been reviewing and testing a lab-scale IPv6 implementation. This also focused on the capabilities incubation for enabling IPv6 on existing telecommunications equipment and interoperability test between the devices. This study provides the result of function, multi-layer integration and interoperability test of IPv6 conducted in Telkom RDC OASIS v6 lab, which also can be considered as references for decision makers within the company to adopt IP technology to be implemented in the future.

Modeling the IPv6 internet AS-level topology

Science.gov (United States)

Xiao, Bo; Liu, Lian-dong; Guo, Xiao-chen; Xu, Ke

2009-02-01

To measure the IPv6 internet AS-level topology, a network topology discovery system, called Dolphin, was developed. By comparing the measurement result of Dolphin with that of CAIDA’s Scamper, it was found that the IPv6 Internet at AS level, similar to other complex networks, is also scale-free but the exponent of its degree distribution is 1.2, which is much smaller than that of the IPv4 Internet and most other scale-free networks. In order to explain this feature of IPv6 Internet we argue that the degree exponent is a measure of uniformity of the degree distribution. Then, for the purpose of modeling the networks, we propose a new model based on the two major factors affecting the exponent of the EBA model. It breaks the lower bound of degree exponent which is 2 for most models. To verify the validity of this model, both theoretical and experimental analyses have been carried out. Finally, we demonstrate how this model can be successfully used to reproduce the topology of the IPv6 Internet.

High-frequency mapping of the IPv6 Internet using Yarrp

OpenAIRE

Gaston, Eric W.

2017-01-01

Approved for public release; distribution is unlimited Both the number of hosts using Internet Protocol version 6 (IPv6), and the volume of IPv6 traffic, has increased exponentially since 2012.With this adoption, the IPv6 routed infrastructure becomes an increasingly important component of global critical infrastructure and network policy. Unfortunately, the tools and techniques used to perform active network topology discovery were designed for Internet Protocol version 4 (IPv4), leading ...

The Department of Defense's Transition of Program of Record (POR) Systems from Internet Protocol Version Four (IPv4) to Internet Protocol Version Six (IPv6)

National Research Council Canada - National Science Library

Perkins, Kyle L; Scott, Michael A

2006-01-01

.... The research outlines the initial intended useful life and limitations of IPv4 and IPv6. The financial aspects of transitioning to IPv6 are examined from a programs perspective, relative to the Program Objective Memorandum (POM...

An Approach to Understanding Cohesive Slurry Settling, Mobilization, and Hydrogen Gas Retention in Pulsed Jet Mixed Vessels

Energy Technology Data Exchange (ETDEWEB)

Gauglitz, Phillip A.; Wells, Beric E.; Fort, James A.; Meyer, Perry A.

2009-05-22

The Hanford Waste Treatment and Immobilization Plant (WTP) is being designed and built to pretreat and vitrify a large portion of the waste in Hanford’s 177 underground waste storage tanks. Numerous process vessels will hold waste at various stages in the WTP. Some of these vessels have mixing-system requirements to maintain conditions where the accumulation of hydrogen gas stays below acceptable limits, and the mixing within the vessels is sufficient to release hydrogen gas under normal conditions and during off-normal events. Some of the WTP process streams are slurries of solid particles suspended in Newtonian fluids that behave as non-Newtonian slurries, such as Bingham yield-stress fluids. When these slurries are contained in the process vessels, the particles can settle and become progressively more concentrated toward the bottom of the vessels, depending on the effectiveness of the mixing system. One limiting behavior is a settled layer beneath a particle-free liquid layer. The settled layer, or any region with sufficiently high solids concentration, will exhibit non-Newtonian rheology where it is possible for the settled slurry to behave as a soft solid with a yield stress. In this report, these slurries are described as settling cohesive slurries.

Spatial data efficient transmission in WebGIS based on IPv6

Science.gov (United States)

Wang, Zhen-feng; Liu, Ji-ping; Wang, Liang; Tao, Kun-wang

2008-12-01

Large-size of spatial data and limited bandwidth of network make it restricted to transmit spatial data in WebGIS. This paper employs IPv6 (Internet Protocol version 6), the successor of IPv4 running now, to transmit spatial data efficiently. As the core of NGN (Next Generation Network), IPv6 brings us many advantages to resolve performance problems in current IPv4 network applications. Multicast, which is mandatory in IPv6 routers, can make one server serve many clients simultaneously efficiently, thus to improve capacity of network applications. The new type of anycast address in IPv6 will make network client applications possible to find the nearest server. This makes data transmission between client and server fastest. The paper introduces how to apply IPv6 multicast and anycast in WebGIS to transmit data efficiently.

ERADIKASI POLIO DAN IPV (INACTIVATED POLIO VACCINE

Directory of Open Access Journals (Sweden)

Gendrowahyuhono Gendrowahyuhono

2012-09-01

Full Text Available In the year 1988, World Health Organization (WHO claims that polio viruses should be eradicated after year 2000. However, until year 2010 the world have not been free from polio viruses circulation. So many effort had been achieved and it is estimated that the world will be free from polio virus after the year 2013. Control of poliomyelitis in Indonesia has been commenced since 1982 with routine immunization of polio program and the National Immunization Days (NID has been commenced since 1995,1996,2005 and 2006. When the world is free from polio virus, WHO suggests several alternative effort to maintain the world free from polio viruses : I stop the OPV (Oral Polio Vaccine and no polio immunization, 2 stop OPV and stock pile mOPV (monovalent OPV, 3 use OPV and IPV (Inactivated Polio Vaccine in a certain times, 4 use IPV only in a certain times. IPV has been used routinely in develop countries but has not been used in the developing countries. Several studies in development countries has been conducted, but had not been done in the developing countries. Indonesia collaboration with WHO has conducted the study of IPV in Yogyakarta Province since year 2002 until year 2010. The overall aim of the study is to compile the necessary data that will inform global and national decision-making regarding future polio immunization policies for the OPV cessation era. The data generated from the study will be particularly important to make decisions regarding optimal IPV use in developing tropical countries. It is unlikely that this data can be assembled through other means than through this study. The tentative result of the study shows that OPV immunization coverage in the year 2004 is 99% in four district and 93 % in the Yogyakarta city. Environment surveillance shows that there are 65.7% polio virus detected from 137 sewage samples pre IPV swich, and 4.8% polio virus detected from 83 sewage samples post IPV swich. Survey polio antibody serologis shows

A Discussion on Internet Security Based on the IPv6 agreement%基于IPv6协议的网络安全问题探讨

Institute of Scientific and Technical Information of China (English)

张贵军

2011-01-01

With the increase of the Internet application of next generation, our government、net service providers and consumers paid more attention to the safety of IPv6. This essay introduced the IPv6 agreement first, then analyzed some security issues. We hope these problems can be solved in the deploy process of IPv6 agreement.%随着下一代互联网应用的不断增加,国家、网络运营商和用户对于IPv6的安全问题日益重视。本文在对IPv6协议简单介绍的基础上,分析了IPv6网络目前存在的一些安全问题,希望在部署IPv6协议的过程中能够不断地解决这些问题。

IPV6 Deployment - Mauritius to benefit from Opportunities and World ...

African Journals Online (AJOL)

user1

gaming, and many other new applications cost even higher to be deployed on IPv4 ... mitigate the effects of the imminent depletion of the IPv4 address space and .... The government of Korea plans to achieve complete IPv6 transition in the.

Protocolo IPv6 com pilha dupla em um campus universitário

Directory of Open Access Journals (Sweden)

Fernando Barreto

2015-11-01

Full Text Available Com o esgotamento do endereçamento IPv4 sendo uma realidade, a adoção do IPv6 se torna cada vez mais necessária. Os protocolos IPv4 e IPv6 são incompatíveis e têm questões de operação diferentes, o que torna a implementação do IPv6 relativamente difícil para administradores de rede IPv4. Com o objetivo de reduzir essa dificuldade, este artigo apresenta uma comparação entre IPv4 e IPv6 com foco no dia a dia de administração de rede de campus. Esse artigo também apresenta as soluções, experiências e lições adquiridas de uma implementação de sucesso do IPv6, utilizando a técnica de Pilha Dupla em um pequeno campus universitário.

A Case Study of IPv6 Network Performance: Packet Delay, Loss, and Reordering

Directory of Open Access Journals (Sweden)

Fuliang Li

2017-01-01

Full Text Available Internet Protocol (IP is used to identify and locate computers on the Internet. Currently, IPv4 still routes most Internet traffic. However, with the exhausting of IPv4 addresses, the transition to IPv6 is imminent, because, as the successor of IPv4, IPv6 can provide a larger available address space. Existing studies have addressed the notion that IPv6-centric next generation networks are widely deployed and applied. In order to gain a deep understanding of IPv6, this paper revisits several critical IPv6 performance metrics. Our extensive measurement shows that packet delay and loss rate of IPv6 are similar to IPv4 when the AS-level paths are roughly the same. Specifically, when the link utilization exceeds a threshold, for example, 0.83 in our study, variation of packet delay presents a similar pattern with the variation of link utilization. If packet delay of a path is large, packet-loss rate of that path is more likely to fluctuate. In addition, we conduct a first-ever analysis of packet reordering in IPv6 world. Few IPv6 probe packets are out-of-order and the reordering rate is 2.3⁎10-6, which is much lower than that of 0.79% in IPv4 world. Our analysis consolidates an experimental basis for operators and researchers of IPv6 networks.

Firewall for Dynamic IP Address in Mobile IPv6

Science.gov (United States)

Qiu, Ying; Bao, Feng; Zhou, Jianying

Mobile communication is becoming the mainstream with the rapid growth of mobile devices penetrating our daily life. More and more mobile devices such as mobile phones, personal digital assistants, notebooks etc, are capable of Internet access. Mobile devices frequently change their communication IP addresses in mobile IPv6 network following its current attached domain. This raises a big challenge for building firewall for mobile devices. The conventional firewalls are primarily based on IPv4 networks where the security criteria are specified only to the fixed IP addresses or subnets, which apparently do not apply to mobile IPv6. In this paper we propose three solutions for mobile IPv6 firewall. Our approaches make the firewall adaptive to dynamic IP addresses in mobile IPv6 network. They have different expense and weight corresponding to different degree of universality. The paper focuses the study more from practical aspect.

IPv6 Monitoring in Nederland : De Nulmeting

NARCIS (Netherlands)

Boen-Leo, M.; Holtzer, A.; Tijmes, M.R.; Smets, R.

2010-01-01

In dit document wordt de mate van uitrol van IPv6 in Nederland per april 2010 beschreven. De 'nulmeting' is uitgevoerd in opdracht van het Ministerie van Ecnomische Zaken en is de eerste van twee metingen die in 2010 worden uitgevoerd. Allereerst wordt een korte uitleg gegeven over IPv6 en het

Hydrogen attack of pressure-vessel steel. Progress report, April 1, 1980-March 31, 1981

International Nuclear Information System (INIS)

Shewmon, P.G.

1980-12-01

The nucleation and growth of methane bubbles in the hydrogen attack of pressure vessel steel has been shown to obey models developed to describe the growth of bubbles limiting the creep ductility of metals. This has been done through studies of the effect of prior deformation on bubble nucleation as well as the effect of methane pressure (stress) and temperature on growth kinetics. A comprehensive model of the factors limiting growth has been developed. Its application to the hydrogen attack of a 2 1/4 Cr-1 Mo steel leads to several interesting predictions

A simplified hydrodynamic model of hydrogen flame propagation in reactor vessels

International Nuclear Information System (INIS)

Baer, M.; Ratzel, A.

1983-01-01

A hydrodynamic model for hydrogen flame propagation in reactor geometries is presented. This model is consistent with the theory of slow combustion in which the gasdynamic field equations are treated in the limit of small Mach numbers. To the lowest order, pressure is spatially uniform. The flame is treated as a density and entropy discontinuity which propagates at prescribed burning velocities, corresponding to laminar or turbulent flames. Radiation cooling of the burned combustion gases and possible preheating of the unburned gases during propagation of the flame is included using a molecular gas-band thermal radiation model. Application of this model has been developed for 1-D variable area flame propagation. Multidimensional effects induced by hydrodynamics and buoyancy are introduced as a correction to the burn velocity (which reflects a modification of planar flame surface to a distorted surface) using experimentally measured pressure-rise time data for hydrogen/air deflagrations in cylindrical vessels. This semianalytical model of flame propagation reduces to a set of ordinary differential equations which describes the temporal variations of vessel pressure, burned volume and gas entropy. The thermodynamic state of the burned gas immediately following the flame is determined using an isobaric Hugoniot relationship. At other locations the burned gas thermodynamic states are determined using a Lagrangian particle tracking method. Results of a computer code using the method are presented

Reclaiming unused IPv4 addresses

CERN Multimedia

IT Department

2016-01-01

As many people might know, the number of IPv4 addresses is limited and almost all have been allocated (see here and here for more information).   Although CERN has been allocated some 340,000 addresses, the way these are allocated across the site is not as efficient as we would like. As we face an increasing demand for IPv4 addresses with the growth in virtual machines, the IT Department’s Communication Systems Group will be reorganising address allocation during 2016 to make more efficient use of the IPv4 address ranges that have been allocated to CERN. We aim, wherever possible, to avoid giving out fixed IP addresses, and have all devices connected to the campus network obtain an address dynamically each time they connect. As a first stage, starting in February, IP addresses that have not been used for more than 9 months will be reclaimed. No information about the devices concerned will be deleted from LANDB, but a new IP address will have to be requested if they are ever reconnected to t...

Characterization testing of a 40 AHR bipolar nickel-hydrogen battery

Science.gov (United States)

Brewer, Jeffrey C.; Manzo, Michelle A.; Gemeiner, Russel P.

1989-01-01

Extensive characterization testing has been done on a second 40 amp-hour (Ahr), 10-cell bipolar nickel-hydrogen (Ni-H2) battery to study the effects of such operating parameters as charge and discharge rates, temperature, and pressure, on capacity, Ahr and watt-hour (Whr) efficiencies, end-of-charge (EOC) and mid-point discharge voltages. Testing to date has produced many interesting results, with the battery performing well throughout all of the test matrix except during the high-rate (5C and 10C) discharges, where poorer than expected results were observed. The exact cause of this poor performance is, as yet, unknown. Small scale 2 x 2 inch battery tests are to be used in studying this problem. Low earth orbit (LEO) cycle life testing at a 40 percent depth of discharge (DOD) and 10 C is scheduled to follow the characterization testing.

Flow-based detection of IPv6-specific network layer attacks

NARCIS (Netherlands)

Hendriks, Luuk; Velan, Petr; de O. Schmidt, Ricardo; de Boer, Pieter-Tjerk; Pras, Aiko; Tuncer, Daphne; Koch, Robert; Badonne, Rémi; Stiller, Burkhard

2017-01-01

With a vastly different header format, IPv6 introduces new vulnerabilities not possible in IPv4, potentially requiring new detection algorithms. While many attacks specific to IPv6 have proven to be possible and are described in the literature, no detection solutions for these attacks have been

Japanese Women’s Perceptions of Intimate Partner Violence (IPV)

Science.gov (United States)

Nagae, Miyoko; Dancy, Barbara L.

2013-01-01

Intimate partner violence (IPV) is a serious problem in Japan. The purpose of this study was to describe IPV as perceived by Japanese adult females who were in a heterosexual marriage and lived with their spouses at the time of IPV. Using a cross-sectional retroactive qualitative description research design with individual face-to-face in-depth interviews, a purposive sample of 11 Japanese adult females from three urban areas in Japan was interviewed. All women reported that they and their husbands were born in Japan. At the time of the interview, the women had a mean age of 38 years whereas at the time of the IPV, their mean age was 28 years. Data was analyzed using the directed qualitative content analysis method. The results revealed that IPV occurred at the women’s homes primarily at night. All the women reported that they experienced physical and emotional abuse and 82% reported experiencing sexual abuse. Additionally, 64% reported that their parents-in-law emotionally abused them. Communication between these women and their husbands were characterized as unilateral with the husbands initiating and dominating the conversations with orders, lectures, and reprimands. The women identified that the cultural influences of the Japanese patriarchal system that reinforces male superiority and dominance and women inferiority were directly related to IPV. The implication is that health professionals need to actively advocate for effective legislation and policies to address IPV in Japan. PMID:19465572

RAZVOJ MODELA IN SIMULACIJA IZČRPANJA IPv4 NASLOVNEGA PROSTORA

OpenAIRE

Ciber, Peter

2014-01-01

Magistrsko delo obravnava razvoj modela in simulacijo izčrpanja IPv4 naslovnega prostora. Za dodeljevanje IPv4 naslovnega prostora skrbi organizacija IANA, ki je po petih celinah sveta dodelila velike kose IPv4 naslovnega prostora. V Evropi tako za nadaljnjo razdelitev skrbi organizacija RIPE NCC, v Afriki AFRINIC, v azijsko-pacifiški regiji APNIC, v Ameriki ARIN v Latinski Ameriki in Karibih pa LACNIC. Zanimalo nas je koliko in kako je IANA razdelila IPv4 naslove po celinah in kako so region...

Platinum-nickel alloy nanoparticles supported on carbon for 3-pentanone hydrogenation

Energy Technology Data Exchange (ETDEWEB)

Zhu, Lihua, E-mail: lihuazhu@stu.xmu.edu.cn [School of Metallurgy and Chemical Engineering, Jiangxi University of Science and Technology, Ganzhou 341000, Jiang Xi (China); Department of Chemical and Biochemical Engineering, National Engineering Laboratory for Green Productions of Alcohols-Ethers-Esters, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China); Zheng, Tuo; Yu, Changlin [School of Metallurgy and Chemical Engineering, Jiangxi University of Science and Technology, Ganzhou 341000, Jiang Xi (China); Zheng, Jinbao [Department of Chemical and Biochemical Engineering, National Engineering Laboratory for Green Productions of Alcohols-Ethers-Esters, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China); Tang, Zhenbiao [School of Metallurgy and Chemical Engineering, Jiangxi University of Science and Technology, Ganzhou 341000, Jiang Xi (China); Zhang, Nuowei [Department of Chemical and Biochemical Engineering, National Engineering Laboratory for Green Productions of Alcohols-Ethers-Esters, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China); Shu, Qing [School of Metallurgy and Chemical Engineering, Jiangxi University of Science and Technology, Ganzhou 341000, Jiang Xi (China); Chen, Bing H., E-mail: chenbh@xmu.edu.cn [Department of Chemical and Biochemical Engineering, National Engineering Laboratory for Green Productions of Alcohols-Ethers-Esters, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China)

2017-07-01

Highlights: • The PtNi/Ni(OH){sub 2}/C catalyst was successfully synthesized at room temperature. • PtNi alloy/C was obtained after PtNi/Ni(OH){sub 2}/C reduced in hydrogen at 300 °C. • Nanostructures of the PtNi catalysts were characterized by numerous techniques. • PtNi alloy/C exhibited high catalytic activity for 3-pentanone hydrogenation. - Abstract: In this work, we prepared the Ni/Ni(OH){sub 2}/C sample at room temperature by hydrazine hydrate reducing method. The galvanic replacement reaction method was applied to deposit platinum on the Ni/Ni(OH){sub 2} nanoparticles, to prepare the PtNi/Ni(OH){sub 2}/C catalyst. The catalyst of platinum-nickel alloy nanoparticles supported on carbon (signed as PtNi/C) was obtained by the thermal treatment of PtNi/Ni(OH){sub 2}/C in flowing hydrogen at 300 °C for 2 h. The size, nanostructure, surface properties, Pt and Ni chemical states of the PtNi/C catalyst were analyzed using powder X-ray diffraction (XRD), transmission electron microscope (TEM) and high resolution transmission electron microscope (HRTEM), high-angle annular dark-field scanning TEM (HAADF-STEM) and elemental energy dispersive X-ray spectroscopy (EDS) line scanning, X-ray photoelectron spectroscopy (XPS) and high-sensitivity low-energy ion scattering spectroscopy (HS-LEIS) techniques. The as-synthesized PtNi/C catalyst showed enhanced catalytic performance relative to the Ni/Ni(OH){sub 2}/C, Ni/C, Pt/C and PtNi/Ni(OH){sub 2}/C catalysts for 3-pentanone hydrogenation due to electron synergistic effect between Pt and Ni species in the PtNi/C catalyst. The PtNi/C catalyst also had exceling stability, with industrial application value.

Decay of Sabin inactivated poliovirus vaccine (IPV)-boosted poliovirus antibodies.

Science.gov (United States)

Resik, Sonia; Tejeda, Alina; Fonseca, Magile; Sein, Carolyn; Hung, Lai Heng; Martinez, Yenisleidys; Diaz, Manuel; Okayasu, Hiromasa; Sutter, Roland W

We conducted a follow-on study to a phase I randomized, controlled trial conducted in Cuba, 2012, to assess the persistence of poliovirus antibodies at 21-22 months following booster dose of Sabin-IPV compared to Salk-IPV in adults who had received multiple doses of oral poliovirus vaccine (OPV) during childhood. In 2012, 60 healthy adult males aged 19-23 were randomized to receive one booster dose, of either Sabin-inactivated poliovirus vaccine (Sabin-IPV), adjuvanted Sabin-IPV (aSabin-IPV), or conventional Salk-IPV. In the original study, blood was collected at days 0 (before) and 28 (after vaccination), respectively. In this study, an additional blood sample was collected 21-22 months after vaccination, and tested for neutralizing antibodies to Sabin poliovirus types 1, 2 and 3. We collected sera from 59/60 (98.3%) subjects; 59/59 (100%) remained seropositive to all poliovirus types, 21-22 months after vaccination. The decay curves were very similar among the study groups. Between day 28 and 21-22 months, there was a reduction of ⩾87.4% in median antibody levels for all poliovirus types in all study groups, with no significant differences between the study groups. The decay of poliovirus antibodies over a 21-22-month period was similar regardless of the type of booster vaccine used, suggesting the scientific data of Salk IPV long-term persistence and decay may be broadly applicable to Sabin IPV.

Análise de campo do desempenho de acessos Web em IPv6.

OpenAIRE

Pirani, Deivis Fernandes

2014-01-01

Este trabalho apresenta um estudo de campo, comparativo, sobre a utilização dos protocolos IPv4 e IPv6 no acesso a páginas web. Foi considerada a perspectiva de um usuário real deste tipo de serviço, no atual período de transição do IPv4 para o IPv6. Para que tal estudo pudesse ser realizado, foi desenvolvido um arranjo no qual três configurações de endereçamento do Protocolo de Internet, IPv4, IPv6 e Pilha Dupla (IPv4+IPv6), foram utilizadas nos acessos às 100 páginas web, com suporte ao I v...

Structural, hydrogen storage and thermodynamic properties of some mischmetal-nickel alloys with partial substitutions for nickel

Energy Technology Data Exchange (ETDEWEB)

Kumar, E. Anil; Maiya, M. Prakash [Department of Mechanical Engineering, Indian Institute of Technology Madras, Chennai 600036 (India); Murthy, S. Srinivasa [Department of Mechanical Engineering, Indian Institute of Technology Madras, Chennai 600036 (India)], E-mail: ssmurthy@iitm.ac.in; Viswanathan, B. [National Centre for Catalysis Research, Indian Institute of Technology Madras, Chennai 600036 (India)

2009-05-12

Mischmetal-nickel (Mm-Ni) alloys with single (Al) and multiple (Al, Co, Mn, Fe) substitutions for Ni are studied for their structural, hydrogen storage and thermodynamic properties. The alloys considered are MmNi{sub 5}, MmNi{sub 4.7}Al{sub 0.3,} MmNi{sub 4.5}Al{sub 0.5}, MmNi{sub 4.2}Al{sub 0.8} and MmNi{sub 4}Al for single substitution, and MmNi{sub 3.9}Co{sub 0.8}Mn{sub 0.2}Al{sub 0.1}, MmNi{sub 3.8}Co{sub 0.7}Mn{sub 0.3}Al{sub 0.2}, MmNi{sub 3.7}Co{sub 0.7}Mn{sub 0.3}Al{sub 0.3}, MmNi{sub 3.6}Co{sub 0.6}Mn{sub 0.3}Al{sub 0.3}Fe{sub 0.2} and MmNi{sub 3.5}Co{sub 0.4}Mn{sub 0.4}Al{sub 0.4}Fe{sub 0.3} for multiple substitutions. The XRD patterns of all the alloys show single phase with the reflection peaks related to the CaCu{sub 5} hexagonal structure. All the multiple substituted alloys absorb and desorb hydrogen at sub-atmospheric pressures. The equilibrium pressure and hysteresis decrease, while enthalpy of formation ({delta}H) and plateau slope increase with increase in unit cell volume, indicating an increase in the stability of the alloys.

Application of IPv6 in GIS

Science.gov (United States)

Wang, Zhen-feng; Wang, Liang

2008-10-01

The inherent flaws in current network, especially the inadequate IP address space, make the born of NGN (Next Generation Network). The NGN aims to enable the information sharing and inter-operation of heterogeneous networks. As the core of NGN, IPv6 (Internet Protocol version 6), which is designed as the successor of IPv4 running now, brings us many new features. It provides larger address space, supports mobile devices, and has built-in security policy, and so on. Although it brings us so many advantages and the backbone of NGN also has been constructed in many countries, we have difficulties moving to NGN. One of the main reasons is there are few killer applications for it. So what features can be employed by GIS, and how to use them is the main content of this paper. The IPv6 certainly offers new entry to solve some problems in GIS.

Graywater Discharges from Vessels

Science.gov (United States)

2011-11-01

metals (e.g., cadmium, chromium, lead, copper , zinc, silver, nickel, and mercury), solids, and nutrients (USEPA, 2008b; USEPA 2010). Wastewater from... flotation ), and disinfection (using ultraviolet light) as compared to traditional Type II MSDs that use either simple maceration and chlorination, or...Coliform Naval Vessels Oceanographic Vessels Small Cruise Ships 25a Vendor 2 Hamann AG Biological Treatment with Dissolved Air Flotation and

Kondisi Migrasi Internet Protocol version 6 (IPv6 di Indonesia

Directory of Open Access Journals (Sweden)

Fahrizal Lukman Budiono

2011-06-01

Full Text Available    Sejalan dengan pertumbuhan industri Internet di Indonesia tersebut, maka kebutuhan akan alamat Internet Protocol (IP juga pasti meningkat. Operator Internet akan membutuhkan alamat IP untuk mengembangkan layanannya hingga ke seluruh pelosok negeri. Saat ini, jaringan Internet di Indonesia berikut perangkat-perangkat pendukungnya hingga di tingkat end user masih menggunakan Internet Protocol version 4 (IPv4. Kenyataan yang dihadapi dunia sekarang adalah menipisnya persediaan alamat IPv4 yang dialokasikan. Hal ini dikarenakan jumlah alamat yang dapat didukung oleh IPv4 adalah 232 bits, sedangkan data terakhir didapatkan bahwa alokasi IPv4 telah habis dialokasikan pada akhir April 2011 di tingkat Internet Assigned Numbers Authority (IANA, organisasi yang mengelola sumberdaya protokol Internet dunia. Untuk mempercepat migrasi, stakeholder internet di Indonesia yaitu Kementerian Komunikasi dan Informatika dan Industri Penyelenggara Internet membentuk ID-IPv6TF. Dalam studi ini, ditemukan bahwa implementasi IPv6 di Indonesia termasuk dalam kategori baik dibandingkan dengan negara lain di dunia. Namun, terlihat bahwa perkembangan ini masih sporadis dengan kurangnya peran koordinator, serta sosialiasi ke masyarakat yang tidak ada.

Decomposition of hydrogen peroxide on nickel oxide - vanadium pentoxide catalysts and the effect of ionizing radiation on them

International Nuclear Information System (INIS)

Mucka, V.

1984-01-01

Some physico-chemical and catalytic properties of nickel oxide-vanadium pentoxide two-component catalysts were studied over the entire concentration range of the components, using the decomposition of hydrogen peroxide in an aqueous solution as the test reaction. The two oxides were found to affect each other; this was shown by the dependences of the specific surface area, the V 4+ ion concentration, and the catalyst activity on the system composition. At low vanadium pentoxide concentrations (up to 15 mol%) the reaction took place on nickel oxide modified with vanadium pentoxide, whereas in the region of higher vanadium pentoxide concentrations the decomposition of the peroxide was catalyzed primarily in the homogeneous phase by vanadium(V) peroxide ions; in a sample with 30 mol% V 2 O 5 , trivalent vanadium also played a part. With catalysts obtained by mere mechanical mixing of the two oxides, a modified activity was observed in the region of high excess of nickel oxide. The activity of catalyst, particularly pure nickel oxide, was increased by its partial reduction and decreased by its exposure to gamma radiation if the dose was higher than 10 5 Gy. The effects observed are interpreted in terms of the concept of bivalent catalytic centres. (author)

IPv6 for Future Wireless Networks

DEFF Research Database (Denmark)

Nielsen, Thomas Toftegaard

2001-01-01

The functionalities of the next generation Internet protocol, IPv6, havebecome increasingly interesting due to the current merging of the traditionalcellular mobile communications and the traditional data-communications intothe future wireless systems, as e.g., UMTS. IPv6 provides several...... enhancedfunctionalities requested for the future mobile systems. In this article thelargest advantages in relation to mobile systems are presented. Variousaspects of introducing IP throughout the entire mobile network (core, accessand termainals) are also presented along with an illustration of the abilitiesof the future...

IPV6 Deployment - Mauritius to benefit from Opportunities and World ...

African Journals Online (AJOL)

The current standard protocol, IPV4, has reached its limit in terms of addressing possibilities, being limited by the 32-bits addressing scheme. Its successor, IPV6, had been devised since the mid 1990's. In addition to handling the address limitations, IPV6 also includes a number of improved features, making it superior to ...

Characterization testing of a 40 ampere hour bipolar nickel-hydrogen battery

Science.gov (United States)

Brewer, Jeffrey C.; Manzo, Michelle A.; Gemeiner, Russel P.

1990-01-01

Extensive characterization testing has been done on a second 40-ampere hour (A h), 10-cell, bipolar nickel-hydrogen (Ni-H2) battery, to study the effects of operating parameters such as charge and discharge rates, temperature, and pressure on capacity, A h and watt hour (W h) efficiencies, and end-of-charge and midpoint discharge voltages. Testing to date has produced many interesting results, with the battery performing well throughout the test matrix except during the high-rate (5 C and 10 C) discharges, where poorer than expected results were observed. The exact cause of this poor performance is, as yet, unknown. Small scale 2 in. x 2 in. battery tests are to be used in studying this problem. Low earth orbit cycle life testing at a 40-percent depth of discharge and 10 C is scheduled to follow the characterization testing.

Performance evaluation of secured DICOM image communication with next generation internet protocol IPv6

Science.gov (United States)

Yu, Fenghai; Zhang, Jianguo; Chen, Xiaomeng; Huang, H. K.

2005-04-01

Next Generation Internet (NGI) technology with new communication protocol IPv6 emerges as a potential solution for low-cost and high-speed networks for image data transmission. IPv6 is designed to solve many of the problems of the current version of IP (known as IPv4) with regard to address depletion, security, autoconfiguration, extensibility, and more. We choose CTN (Central Test Node) DICOM software developed by The Mallinckrodt Institute of Radiology to implement IPv6/IPv4 enabled DICOM communication software on different operating systems (Windows/Linux), and used this DICOM software to evaluate the performance of the IPv6/IPv4 enabled DICOM image communication with different security setting and environments. We compared the security communications of IPsec with SSL/TLS on different TCP/IP protocols (IPv6/IPv4), and find that there are some trade-offs to choose security solution between IPsec and SSL/TLS in the security implementation of IPv6/IPv4 communication networks.

Hydrogen permeation on Al{sub 2}O{sub 3}-based nickel/cobalt composite membranes

Energy Technology Data Exchange (ETDEWEB)

Park, Jihee; Jung, Miewon [Department of Chemistry/Institute of Basic Science, Sungshin Women' s University, Seoul 136-742 (Korea, Republic of); Hong, Tae-Whan [Department of Materials Science and Engineering/Research Center for Sustainable Eco-Devices and Materials(ReSEM), Chungju National University, Chungju 380-702 (Korea, Republic of)

2010-12-15

Al{sub 2}O{sub 3} was synthesized using the sol-gel process with aluminum isopropoxide as the precursor and primary distilled water as the solvent. Nickel and cobalt metal powders were used to increase the strength of the membranes. The Al{sub 2}O{sub 3}-based membranes were prepared using HPS following a mechanical alloying process. The phase transformation, thermal evolution, surface and cross-section morphology of Al{sub 2}O{sub 3} and Al{sub 2}O{sub 3}-based membranes were characterized by XRD, TG-DTA and FE-SEM. The hydrogen permeation of Al{sub 2}O{sub 3}-based membranes was examined at 300-473 K under increasing pressure. Hydrogen permeation flux through an Al{sub 2}O{sub 3}-20wt%Co membrane was obtained to 2.36 mol m{sup -2} s{sup -1}. Reaction enthalpy was calculated to 4.5 kJ/mol using a Van't Hoff's plot. (author)

The Impact of IPv6 on Penetration Testing

NARCIS (Netherlands)

Ottow, Christiaan; van Vliet, Frank; de Boer, Pieter-Tjerk; Pras, Aiko

In this paper we discuss the impact the use of IPv6 has on remote penetration testing of servers and web applications. Several modifications to the penetration testing process are proposed to accommodate IPv6. Among these modifications are ways of performing fragmentation attacks, host discovery and

Highly efficient photocatalytic hydrogen evolution from nickel quinolinethiolate complexes under visible light irradiation

Science.gov (United States)

Rao, Heng; Yu, Wen-Qian; Zheng, Hui-Qin; Bonin, Julien; Fan, Yao-Ting; Hou, Hong-Wei

2016-08-01

Earth-abundant metal complexes have emerged as promising surrogates of platinum for catalyzing the hydrogen evolution reaction (HER). In this study, we report the design and synthesis of two novel nickel quinolinethiolate complexes, namely [Ni(Hqt)2(4, 4‧-Z-2, 2‧-bpy)] (Hqt = 8-quinolinethiol, Z = sbnd H [1] or sbnd CH3 [2], bpy = bipyridine). An efficient three-component photocatalytic homogeneous system for hydrogen generation working under visible light irradiation was constructed by using the target complexes as catalysts, triethylamine (TEA) as sacrificial electron donor and xanthene dyes as photosensitizer. We obtain turnover numbers (TON, vs. catalyst) for H2 evolution of 5923/7634 under the optimal conditions with 5.0 × 10-6 M complex 1/2 respectively, 1.0 × 10-3 M fluorescein and 5% (v/v) TEA at pH 12.3 in EtOH/H2O (1:1, v/v) mixture after 8 h irradiation (λ > 420 nm). We discuss the mechanism of H2 evolution in the homogeneous photocatalytic system based on fluorescence spectrum and cyclic voltammetry data.

Active Edge Sites Engineering in Nickel Cobalt Selenide Solid Solutions for Highly Efficient Hydrogen Evolution

KAUST Repository

Xia, Chuan

2017-01-06

An effective multifaceted strategy is demonstrated to increase active edge site concentration in NiCoSe solid solutions prepared by in situ selenization process of nickel cobalt precursor. The simultaneous control of surface, phase, and morphology result in as-prepared ternary solid solution with extremely high electrochemically active surface area (C = 197 mF cm), suggesting significant exposure of active sites in this ternary compound. Coupled with metallic-like electrical conductivity and lower free energy for atomic hydrogen adsorption in NiCoSe, identified by temperature-dependent conductivities and density functional theory calculations, the authors have achieved unprecedented fast hydrogen evolution kinetics, approaching that of Pt. Specifically, the NiCoSe solid solutions show a low overpotential of 65 mV at -10 mV cm, with onset potential of mere 18 mV, an impressive small Tafel slope of 35 mV dec, and a large exchange current density of 184 μA cm in acidic electrolyte. Further, it is shown that the as-prepared NiCoSe solid solution not only works very well in acidic electrolyte but also delivers exceptional hydrogen evolution reaction (HER) performance in alkaline media. The outstanding HER performance makes this solid solution a promising candidate for mass hydrogen production.

Evaluation de la mise en ceuvre des services du protocole IPV6 ...

African Journals Online (AJOL)

At present, the configurations of networks are based on the protocol ipv4. The addresses ipv4 begin to run out. Groups of search work on the new version of the protocol IPV6 (in France, in United States, in Japan). Certain networks run under ipv6. However the great majority of the existing networks always use the ...

Early construction and operation of the highly contaminated water treatment system in Fukushima Daiichi Nuclear Power Station (4). Assessment of hydrogen behavior in stored Cs adsorption vessel

International Nuclear Information System (INIS)

Kondo, Masahiro; Arai, Takahiro; Nishi, Yoshihisa

2014-01-01

Hydrogen diffusion behavior in a cesium adsorption vessel is assessed. The vessel is used to remove radioactive substance from contaminated water, which is proceeded from Fukushima accident. Experiment and numerical calculation are conducted to clarify the characteristics of natural circulation in the vessel. The natural circulation arising from the temperature difference between inside and outside the vessel is confirmed. We develop an evaluation model to predict the natural circulation and its prediction agrees well with the results obtained by the experiment and the calculation. Using the model, we predict steady and transient behavior of hydrogen concentration. Results indicate that hydrogen concentration is kept lower than the flammability limit when the short vent pipe is open. (author)

Hydrogen Gas Retention and Release from WTP Vessels: Summary of Preliminary Studies

Energy Technology Data Exchange (ETDEWEB)

Gauglitz, Phillip A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Bontha, Jagannadha R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Daniel, Richard C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Mahoney, Lenna A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rassat, Scot D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wells, Beric E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Bao, Jie [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Boeringa, Gregory K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Buchmiller, William C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Burns, Carolyn A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Chun, Jaehun [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Karri, Naveen K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Li, Huidong [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tran, Diana N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-07-01

The Hanford Waste Treatment and Immobilization Plant (WTP) is currently being designed and constructed to pretreat and vitrify a large portion of the waste in the 177 underground waste storage tanks at the Hanford Site. A number of technical issues related to the design of the pretreatment facility (PTF) of the WTP have been identified. These issues must be resolved prior to the U.S. Department of Energy (DOE) Office of River Protection (ORP) reaching a decision to proceed with engineering, procurement, and construction activities for the PTF. One of the issues is Technical Issue T1 - Hydrogen Gas Release from Vessels (hereafter referred to as T1). The focus of T1 is identifying controls for hydrogen release and completing any testing required to close the technical issue. In advance of selecting specific controls for hydrogen gas safety, a number of preliminary technical studies were initiated to support anticipated future testing and to improve the understanding of hydrogen gas generation, retention, and release within PTF vessels. These activities supported the development of a plan defining an overall strategy and approach for addressing T1 and achieving technical endpoints identified for T1. Preliminary studies also supported the development of a test plan for conducting testing and analysis to support closing T1. Both of these plans were developed in advance of selecting specific controls, and in the course of working on T1 it was decided that the testing and analysis identified in the test plan were not immediately needed. However, planning activities and preliminary studies led to significant technical progress in a number of areas. This report summarizes the progress to date from the preliminary technical studies. The technical results in this report should not be used for WTP design or safety and hazards analyses and technical results are marked with the following statement: “Preliminary Technical Results for Planning – Not to be used for WTP Design

Plated nickel wire mesh makes superior catalyst bed

Science.gov (United States)

Sill, M.

1965-01-01

Porous nickel mesh screen catalyst bed produces gas evolution in hydrogen peroxide thrust chambers used for attitude control of space vehicles. The nickel wire mesh disks in the catalyst bed are plated in rugose form with a silver-gold coating.

A Brief History of MPLS Usage in IPv6

OpenAIRE

Vanaubel, Yves; Mérindol, Pascal; Pansiot, Jean-Jacques; Donnet, Benoît

2016-01-01

Recent researches have stated the fast deployment of IPv6. It has been demonstrated that IPv6 grows much faster, being so more and more adopted by both Internet service providers but also by servers and end-hosts. In parallel, researches have been conducted to discover and assess the usage of MPLS tunnels. Indeed, recent developments in the ICMP protocol make certain categories of MPLS tunnels transparent to traceroute probing. However, these studies focus only on IPv4, where MPLS is st...

New generation of full composite vessels for 70 MPa gaseous hydrogen storage : results and achievements of the French HyBou project

Energy Technology Data Exchange (ETDEWEB)

Nony, F. [CEA Materials, Monts (France); Weber, M. [Air Liquide, Paris (France); Tcharkhtchi, A. [Ecole Nationale Superieure d' Arts et Metiers, Paris (France); Lafarie-Frenot, M.C. [Ecole Nationale Superique De Mecanique et d' Aerotechnique, Poitiers (France); Perrier, O. [Raigi, Arbouville (France)

2009-07-01

The French collaborative Project known as HyBou explores hydrogen storage as a key enabling technology for the extensive use of hydrogen as an energy carrier. HyBou aims to develop robust, safe and efficient compressed gaseous hydrogen (CGH2) storage systems and validate innovative materials and processes suitable for storage vessel manufacturing with improved performance at low cost. The development of a new generation of type-4 70 MPa vessel was described along with a newly developed liner based on polyurethane materials. The new liner presents increased thermal stability, hydrogen barrier properties and cost effectiveness. The project also aims to evaluate the potential of new high resistance fibers and develop an improved thermosetting resin for composite winding with enhanced mechanical resistance and durability. A specific apparatus was therefore designed to characterize and evaluate coupled thermal and mechanical fatigue resistance in representative conditions.

Direct Aldehyde C-H Arylation and Alkylation via the Combination of Nickel, Hydrogen Atom Transfer, and Photoredox Catalysis.

Science.gov (United States)

Zhang, Xiaheng; MacMillan, David W C

2017-08-23

A mechanism that enables direct aldehyde C-H functionalization has been achieved via the synergistic merger of photoredox, nickel, and hydrogen atom transfer catalysis. This mild, operationally simple protocol transforms a wide variety of commercially available aldehydes, along with aryl or alkyl bromides, into the corresponding ketones in excellent yield. This C-H abstraction coupling technology has been successfully applied to the expedient synthesis of the medicinal agent haloperidol.

Multiscale modelling and experimentation of hydrogen embrittlement in aerospace materials

Science.gov (United States)

Jothi, Sathiskumar

Pulse plated nickel and nickel based superalloys have been used extensively in the Ariane 5 space launcher engines. Large structural Ariane 5 space launcher engine components such as combustion chambers with complex microstructures have usually been manufactured using electrodeposited nickel with advanced pulse plating techniques with smaller parts made of nickel based superalloys joined or welded to the structure to fabricate Ariane 5 space launcher engines. One of the major challenges in manufacturing these space launcher components using newly developed materials is a fundamental understanding of how different materials and microstructures react with hydrogen during welding which can lead to hydrogen induced cracking. The main objective of this research has been to examine and interpret the effects of microstructure on hydrogen diffusion and hydrogen embrittlement in (i) nickel based superalloy 718, (ii) established and (iii) newly developed grades of pulse plated nickel used in the Ariane 5 space launcher engine combustion chamber. Also, the effect of microstructures on hydrogen induced hot and cold cracking and weldability of three different grades of pulse plated nickel were investigated. Multiscale modelling and experimental methods have been used throughout. The effect of microstructure on hydrogen embrittlement was explored using an original multiscale numerical model (exploiting synthetic and real microstructures) and a wide range of material characterization techniques including scanning electron microscopy, 2D and 3D electron back scattering diffraction, in-situ and ex-situ hydrogen charged slow strain rate tests, thermal spectroscopy analysis and the Varestraint weldability test. This research shows that combined multiscale modelling and experimentation is required for a fundamental understanding of microstructural effects in hydrogen embrittlement in these materials. Methods to control the susceptibility to hydrogen induced hot and cold cracking and

IPv6 in ESnet

International Nuclear Information System (INIS)

Matthews, W.; Fink, B.; Hicks, S.; Grigaliunas, V.

2001-01-01

The importance of the Internet to modern High Energy Physics collaborators is clearly immense, and understanding how new developments in network technology impact networks is critical to the future design of experiments. The next generation Internet Protocol (IPv6) is being deployed on testbeds and production networks throughout the world. The protocol has been designed to solve todays internet problems, and many of the features will be core Internet services in the future. In this talk the features of the protocol will be described. Details will be given on the deployment at sites important to High Energy Physics Research and the network services operating at these sites. In particular IPv6 deployment on the U.S. Energy Sciences Network (ESnet) will be reviewed. The connectivity and performance between High Energy Physics Laboratories, Universities and Institutes will be discussed

Modeling a constant power load for nickel-hydrogen battery testing using SPICE

Science.gov (United States)

Bearden, Douglas B.; Lollar, Louis F.; Nelms, R. M.

1990-01-01

The effort to design and model a constant power load for the HST (Hubble Space Telescope) nickel-hydrogen battery tests is described. The constant power load was designed for three different simulations on the batteries: life cycling, reconditioning, and capacity testing. A dc-dc boost converter was designed to act as this constant power load. A boost converter design was chosen because of the low test battery voltage (4 to 6 VDC) generated and the relatively high power requirement of 60 to 70 W. The SPICE model was shown to consistently predict variations in the actual circuit as various designs were attempted. It is concluded that the confidence established in the SPICE model of the constant power load ensures its extensive utilization in future efforts to improve performance in the actual load circuit.

The Rise of IPv6: Benefits and Costs of Transforming Military Cyberspace

Science.gov (United States)

2015-04-01

people, the structure of the Internet is changing for the first time in its history with the ex- haustion of the IP version four ( IPv4 ) protocol and the...have.4 The need to transition from IPv4 to IPv6 is not hy- pothetical since the global supply of IP addresses in IPv4 is quickly be- ing exhausted...Registry (RIR) IPv4 Address Run-Down Model Year RI R Ad dr es s Po ol (/ 8s ) 2013 2014 2015 2016 2017 2018 2019 2020 4.5 4 3.5 3 2.5 2 1.5 1 0.5

Selective Hydrogen Atom Abstraction through Induced Bond Polarization: Direct α-Arylation of Alcohols through Photoredox, HAT, and Nickel Catalysis.

Science.gov (United States)

Twilton, Jack; Christensen, Melodie; DiRocco, Daniel A; Ruck, Rebecca T; Davies, Ian W; MacMillan, David W C

2018-05-04

The combination of nickel metallaphotoredox catalysis, hydrogen atom transfer catalysis, and a Lewis acid activation mode, has led to the development of an arylation method for the selective functionalization of alcohol α-hydroxy C-H bonds. This approach employs zinc-mediated alcohol deprotonation to activate α-hydroxy C-H bonds while simultaneously suppressing C-O bond formation by inhibiting the formation of nickel alkoxide species. The use of Zn-based Lewis acids also deactivates other hydridic bonds such as α-amino and α-oxy C-H bonds. This approach facilitates rapid access to benzylic alcohols, an important motif in drug discovery. A 3-step synthesis of the drug Prozac exemplifies the utility of this new method. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

The design of IPv6's transitional scheme in university

Science.gov (United States)

Li, Biqing; Li, Zhao

2017-05-01

According to the current network environment of campus, the specific scheme of network transition is proposed, which has conducted detailed analyses for the basic concepts, the types of address, the necessary technology for transition and the agreement and principle of transition. According to the tunneling technology of IPv6, the IPv4 network and IPv6 network can communicate with each other, and the network of whole campus can operate well.

V1.6 Development of Advanced Manufacturing Technologies for Low Cost Hydrogen Storage Vessels

Energy Technology Data Exchange (ETDEWEB)

Leavitt, Mark; Lam, Patrick; Nelson, Karl M.; johnson, Brice A.; Johnson, Kenneth I.; Alvine, Kyle J.; Ruiz, Antonio; Adams, Jesse

2012-10-01

The goal of this project is to develop an innovative manufacturing process for Type IV high-pressure hydrogen storage vessels, with the intent to significantly lower manufacturing costs. Part of the development is to integrate the features of high precision AFP and commercial FW. Evaluation of an alternative fiber to replace a portion of the baseline fiber will help to reduce costs further.

IPV among Adolescent Reproductive Health Patients: The Role of Relationship Communication

Science.gov (United States)

Messinger, Adam M.; Davidson, Leslie L.; Rickert, Vaughn I.

2011-01-01

Population-specific data on factors that affect intimate partner violence (IPV) are needed on female adolescents and young adults, a cohort at greatest risk of IPV in the United States (Rennison, 2001). Studies have frequently overlooked the role of relationship communication as a gatekeeper to IPV (Ridley & Feldman, 2003). To address this…

Comparison of BR3 Surveillance and Vessel Plates to the Surrogate Plates Representative of the Yankee Rowe PWR Vessel

Energy Technology Data Exchange (ETDEWEB)

Fabry, A.; Chaouadi, R.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rosinski, S.T.; Carter, R.G

1998-07-01

The sister pressure vessels at the BR3 and Yankee Rowe PWR plants were operated at lower-than-usual temperature ( 260 degrees Celsius) and their plates were austenitized a higher-than-usual temperature (970 degrees Celsius) - a heat treatment leading to a coarser microstructure than is typical for the fine grain plates considered in development of USNRC Regulatory Guide 1.99. The surveillance programs provided by Westinghouse for the two plants were limited to the same A302-B plate representative of the Rowe vessel upper shell plate; this material displayed outlier behaviour characterized by a 41 J Charpy-V Notch shift significantly larger than predicted by Regulatory Guide 1.99. Because lower irradiation temperature and nickel alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rate plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements embodied in the PTS screening criterion. This paper compares free complementary studies undertaken to clarify these uncertainties: (1) The accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63 % (A533-B) and YA9, 0.19 (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively; (2) The BR3 surveillance and vessel testing program: this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, and was trepanned in early 1995; (3) The accelerated irradiations in the Belgian test reactor BR2 of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is contended that the PTS screening criterion was never attained by the BR3 and Rowe plates, and

Comparison of BR3 Surveillance and Vessel Plates to the Surrogate Plates Representative of the Yankee Rowe PWR Vessel

International Nuclear Information System (INIS)

Fabry, A.; Chaouadi, R.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rosinski, S.T.; Carter, R.G.

1998-07-01

The sister pressure vessels at the BR3 and Yankee Rowe PWR plants were operated at lower-than-usual temperature ( 260 degrees Celsius) and their plates were austenitized a higher-than-usual temperature (970 degrees Celsius) - a heat treatment leading to a coarser microstructure than is typical for the fine grain plates considered in development of USNRC Regulatory Guide 1.99. The surveillance programs provided by Westinghouse for the two plants were limited to the same A302-B plate representative of the Rowe vessel upper shell plate; this material displayed outlier behaviour characterized by a 41 J Charpy-V Notch shift significantly larger than predicted by Regulatory Guide 1.99. Because lower irradiation temperature and nickel alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rate plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements embodied in the PTS screening criterion. This paper compares free complementary studies undertaken to clarify these uncertainties: (1) The accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63 % (A533-B) and YA9, 0.19 (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively; (2) The BR3 surveillance and vessel testing program: this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, and was trepanned in early 1995; (3) The accelerated irradiations in the Belgian test reactor BR2 of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is contended that the PTS screening criterion was never attained by the BR3 and Rowe plates, and

Comparison of BR3 surveillance and vessel plates to the surrogate plates representative of the Yankee Rowe PWR vessel

International Nuclear Information System (INIS)

Fabry, A.; Chaouadi, R.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rosinski, S.T.; Carter, R.G.

1999-01-01

The sister pressure vessels at the BR3 and Yankee Rowe PWR plants were operated at lower-than-usual temperature (∼260 C) and their plates were austenitized at higher-than-usual temperature (∼970 C) -- a heat treatment leading to a coarser microstructure than is typical for the fine grain plates considered in development of USNRC Regulatory Guide 1.99. The surveillance programs provided by Westinghouse for the two plants were limited to the same A302-B plate representative of the Rowe vessel upper shell plate; this material displayed outlier behavior characterized by a 41J. Charpy-V Notch shift significantly larger than predicted by Regulatory Guide 1.99. Because lower irradiation temperature and nickel alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rowe plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements embodied in the PTS screening criterion. This paper compares three complementary studies undertaken to clarify these uncertainties: (1) The accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63% (A533-B) and YA9, 0.19% (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively; (2) The BR3 surveillance and vessel testing program; this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, and was trepanned in early 1995; (3) The accelerated irradiations in the Belgian test reactor BR2 of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is contended that the PTS screening criterion was never attained by the BR3 and Rowe plates, and that the BR3 vessel

Analysis of Pressure Variations in a Low-Pressure Nickel-Hydrogen Battery- Part 2: Cells with Metal Hydride Storage.

Science.gov (United States)

Purushothaman, B K; Wainright, J S

2012-05-15

A sub-atmospheric pressure nickel hydrogen (Ni-H(2)) battery with metal hydride for hydrogen storage is developed for implantable neuroprosthetic devices. Pressure variations during charge and discharge of the cell are analyzed at different states of charge and are found to follow the desorption curve of the pressure composition isotherm (PCI) of the metal hydride. The measured pressure agreed well with the calculated theoretical pressure based on the PCI and is used to predict the state of charge of the battery. Hydrogen equilibration with the metal hydride during charge/discharge cycling is fast when the pressure is in the range from 8 to 13 psia and slower in the range from 6 to 8 psia. The time constant for the slower hydrogen equilibration, 1.37h, is similar to the time constant for oxygen recombination and therefore pressure changes due to different mechanisms are difficult to estimate. The self-discharge rate of the cell with metal hydride is two times lower in comparison to the cell with gaseous hydrogen storage alone and is a result of the lower pressure in the cell when the metal hydride is used.

Analysis of Pressure Variations in a Low-Pressure Nickel-Hydrogen Battery– Part 2: Cells with Metal Hydride Storage

Science.gov (United States)

Purushothaman, B. K.; Wainright, J. S.

2012-01-01

A sub-atmospheric pressure nickel hydrogen (Ni-H2) battery with metal hydride for hydrogen storage is developed for implantable neuroprosthetic devices. Pressure variations during charge and discharge of the cell are analyzed at different states of charge and are found to follow the desorption curve of the pressure composition isotherm (PCI) of the metal hydride. The measured pressure agreed well with the calculated theoretical pressure based on the PCI and is used to predict the state of charge of the battery. Hydrogen equilibration with the metal hydride during charge/discharge cycling is fast when the pressure is in the range from 8 to 13 psia and slower in the range from 6 to 8 psia. The time constant for the slower hydrogen equilibration, 1.37h, is similar to the time constant for oxygen recombination and therefore pressure changes due to different mechanisms are difficult to estimate. The self-discharge rate of the cell with metal hydride is two times lower in comparison to the cell with gaseous hydrogen storage alone and is a result of the lower pressure in the cell when the metal hydride is used. PMID:22711974

A Comparison of Internet Protocol (IPv6 Security Guidelines

Directory of Open Access Journals (Sweden)

Steffen Hermann

2014-01-01

Full Text Available The next generation of the Internet Protocol (IPv6 is currently about to be introduced in many organizations. However, its security features are still a very novel area of expertise for many practitioners. This study evaluates guidelines for secure deployment of IPv6, published by the U.S. NIST and the German federal agency BSI, for topicality, completeness and depth. The later two are scores defined in this paper and are based on the Requests for Comments relevant for IPv6 that were categorized, weighted and ranked for importance using an expert survey. Both guides turn out to be of practical value, but have a specific focus and are directed towards different audiences. Moreover, recommendations for possible improvements are presented. Our results could also support strategic management decisions on security priorities as well as for the choice of security guidelines for IPv6 roll-outs.

Konsep Tingkat Kematangan penerapan Internet Protokol versi 6 (Capability Maturity Model for IPv6 Implementation

Directory of Open Access Journals (Sweden)

Riza Azmi

2015-03-01

Full Text Available Internet Protocol atau IP merupakan standar penomoran internet di dunia yang jumlahnya terbatas. Di dunia, alokasi IP diatur oleh Internet Assignd Number Authority (IANA dan didelegasikan ke melalui otoritas masing-masing benua. IP sendiri terdiri dari 2 jenis versi yaitu IPv4 dan IPv6 dimana alokasi IPv4 dinyatakan habis di tingkat IANA pada bulan April 2011. Oleh karena itu, penggunaan IP diarahkan kepada penggunaan IPv6. Untuk melihat bagaimana kematangan suatu organisasi terhadap implementasi IPv6, penelitian ini mencoba membuat sebuah model tingkat kematangan penerapan IPv6. Konsep dasar dari model ini mengambil konsep Capability Maturity Model Integrated (CMMI, dengan beberapa tambahan yaitu roadmap migrasi IPv6 di Indonesia, Request for Comment (RFC yang terkait dengan IPv6 serta beberapa best-practice implementasi dari IPv6. Dengan konsep tersebut, penelitian ini menghasilkan konsep Capability Maturity for IPv6 Implementation.

Empirical analysis of the effects and the mitigation of IPv4 address exhaustion

OpenAIRE

Richter, Philipp

2017-01-01

IP addresses are essential resources for communication over the Internet. In IP version 4, an address is represented by 32 bits in the IPv4 header; hence there is a finite pool of roughly 4B addresses available. The Internet now faces a fundamental resource scarcity problem: The exhaustion of the available IPv4 address space. In 2011, the Internet Assigned Numbers Authority (IANA) depleted its pool of available IPv4 addresses. IPv4 scarcity is now reality. In the subsequent years, IPv4 a...

Research on IPv6 intrusion detection system Snort-based

Science.gov (United States)

Shen, Zihao; Wang, Hui

2010-07-01

This paper introduces the common intrusion detection technologies, discusses the work flow of Snort intrusion detection system, and analyzes IPv6 data packet encapsulation and protocol decoding technology. We propose the expanding Snort architecture to support IPv6 intrusion detection in accordance with CIDF standard combined with protocol analysis technology and pattern matching technology, and present its composition. The research indicates that the expanding Snort system can effectively detect various intrusion attacks; it is high in detection efficiency and detection accuracy and reduces false alarm and omission report, which effectively solves the problem of IPv6 intrusion detection.

Intimate partner violence: office screening for victims and perpetrators of IPV.

Science.gov (United States)

Chen, Ping-Hsin; Jacobs, Abbie; Rovi, Susan L D

2013-09-01

Intimate partner violence (IPV) affects more than 12 million individuals annually. Power and control are central concepts underlying abusive relationships. Physicians may see IPV victims, perpetrators, and their children for annual examinations, as well as for injuries and health conditions associated with abuse. In 2013, the US Preventive Services Task Force recommended that women of childbearing age (ie, 14 to 46 years) be screened for IPV. Brief, validated screening tools, such as the 4-item Hurt, Insult, Threaten, and Scream (HITS), can be used to facilitate screening. Physicians should always assess patients whose medical histories or presenting symptoms or injuries are consistent with abuse. Risk factors for IPV and consequences of abuse include general health conditions (eg, asthma, irritable bowel syndrome), reproductive issues (eg, gynecologic disorders, unintended pregnancies), psychological conditions (eg, depression, sleep disturbances), and risky health behaviors (eg, substance use, poor health care adherence). Tools for identifying perpetrators are under investigation. To prepare the practice to address IPV, physicians should educate themselves and staff and learn about community and national resources. By identifying and responding to IPV, clinicians may be able to reduce IPV and interrupt the intergenerational cycle of violence. Written permission from the American Academy of Family Physicians is required for reproduction of this material in whole or in part in any form or medium.

Enabling IPv6 at FZU - WLCG Tier2 in Prague

International Nuclear Information System (INIS)

Kouba, Tomáš; Chudoba, Jiří; Eliáš, Marek

2014-01-01

The usage of the new IPv6 protocol in production is becoming reality in the HEP community and the Computing Centre of the Institute of Physics in Prague participates in many IPv6 related activities. Our contribution presents experience with monitoring in HEPiX distributed IPv6 testbed which includes 11 remote sites. We use Nagios to check availability of services and Smokeping for monitoring the network latency. Since it is not always trivial to setup DNS in a dual stack environment properly, we developed a Nagios plugin for checking whether a domain name is resolvable when using only IP protocol version 6 and only version 4. We will also present local area network monitoring and tuning related to IPv6 performance. One of the most important software for a grid site is a batch system for a job execution. We will present our experience with configuring and running Torque batch system in a dual stack environment. We also discuss the steps needed to run VO specific jobs in our IPv6 testbed.

Enabling IPv6 at FZU - WLCG Tier2 in Prague

Science.gov (United States)

Kouba, Tomáš; Chudoba, Jiří; Eliáš, Marek

2014-06-01

The usage of the new IPv6 protocol in production is becoming reality in the HEP community and the Computing Centre of the Institute of Physics in Prague participates in many IPv6 related activities. Our contribution presents experience with monitoring in HEPiX distributed IPv6 testbed which includes 11 remote sites. We use Nagios to check availability of services and Smokeping for monitoring the network latency. Since it is not always trivial to setup DNS in a dual stack environment properly, we developed a Nagios plugin for checking whether a domain name is resolvable when using only IP protocol version 6 and only version 4. We will also present local area network monitoring and tuning related to IPv6 performance. One of the most important software for a grid site is a batch system for a job execution. We will present our experience with configuring and running Torque batch system in a dual stack environment. We also discuss the steps needed to run VO specific jobs in our IPv6 testbed.

Design of Hydrogen Storage Alloys/Nanoporous Metals Hybrid Electrodes for Nickel-Metal Hydride Batteries

Science.gov (United States)

Li, M. M.; Yang, C. C.; Wang, C. C.; Wen, Z.; Zhu, Y. F.; Zhao, M.; Li, J. C.; Zheng, W. T.; Lian, J. S.; Jiang, Q.

2016-06-01

Nickel metal hydride (Ni-MH) batteries have demonstrated key technology advantages for applications in new-energy vehicles, which play an important role in reducing greenhouse gas emissions and the world’s dependence on fossil fuels. However, the poor high-rate dischargeability of the negative electrode materials—hydrogen storage alloys (HSAs) limits applications of Ni-MH batteries in high-power fields due to large polarization. Here we design a hybrid electrode by integrating HSAs with a current collector of three-dimensional bicontinuous nanoporous Ni. The electrode shows enhanced high-rate dischargeability with the capacity retention rate reaching 44.6% at a discharge current density of 3000 mA g-1, which is 2.4 times that of bare HSAs (18.8%). Such a unique hybrid architecture not only enhances charge transfer between nanoporous Ni and HSAs, but also facilitates rapid diffusion of hydrogen atoms in HSAs. The developed HSAs/nanoporous metals hybrid structures exhibit great potential to be candidates as electrodes in high-performance Ni-MH batteries towards applications in new-energy vehicles.

Electro-activity of cobalt and nickel complexes for the reduction of protons into di-hydrogen. Application to PEM water electrolysis

International Nuclear Information System (INIS)

Pantani, O.; Anxolabehere, E.; Aukauloo, A.; Millet, P.

2006-01-01

Proton exchange membrane (PEM) water electrolysis is a safe and efficient way to perform water splitting into di-hydrogen and di-oxygen. In a PEM water electrolyser, platinum is commonly used as electro-catalyst on the cathodic side of the cells, mostly because of its efficiency for hydrogen evolution. But for cost considerations, there is a need to find alternative low-cost electrocatalysts. Molecular chemistry offers the possibility of synthesizing new compounds for this purpose, such as transition metal complexes. Results obtained with nickel- and cobalt-oximes compounds are presented in this paper. They have been chemically (1H NMR, EPR) and electrochemically (voltametry, spectro-electrochemistry) characterized. Their ability to electrochemically reduce protons into di-hydrogen when they are either dissolved in solution or immobilized at the surface of a solid electrode is discussed. (authors)

Decay of Sabin inactivated poliovirus vaccine (IPV)-boosted poliovirus antibodies

OpenAIRE

Resik, Sonia; Tejeda, Alina; Fonseca, Magile; Sein, Carolyn; Hung, Lai Heng; Martinez, Yenisleidys; Diaz, Manuel; Okayasu, Hiromasa; Sutter, Roland W.

2015-01-01

Introduction: We conducted a follow-on study to a phase I randomized, controlled trial conducted in Cuba, 2012, to assess the persistence of poliovirus antibodies at 21–22 months following booster dose of Sabin-IPV compared to Salk-IPV in adults who had received multiple doses of oral poliovirus vaccine (OPV) during childhood. Methods: In 2012, 60 healthy adult males aged 19–23 were randomized to receive one booster dose, of either Sabin-inactivated poliovirus vaccine (Sabin-IPV), adjuvant...

Sintering of nickel catalysts. Effects of time, atmosphere, temperature, nickel-carrier interactions, and dopants

Energy Technology Data Exchange (ETDEWEB)

Sehested, Jens; Gelten, Johannes A.P.; Helveg, Stig [Haldor Topsoee A/S, Nymoellevej 55, DK-2800 Kgs. Lyngby (Denmark)

2006-08-01

Supported nickel catalysts are widely used in the steam-reforming process for industrial scale production of hydrogen and synthesis gas. This paper provides a study of sintering in nickel-based catalysts (Ni/Al{sub 2}O{sub 3} and Ni/MgAl{sub 2}O{sub 4}). Specifically the influence of time, temperature, atmosphere, nickel-carrier interactions and dopants on the rate of sintering is considered. To probe the sintering kinetics, all catalysts were analyzed by sulfur chemisorption to determine the Ni surface area. Furthermore selected samples were further analyzed using X-ray diffraction (XRD), mercury porosimetry, BET area measurements, and electron microscopy (EM). The observed sintering rates as a function of time, temperature, and P{sub H{sub 2}O}/P{sub H{sub 2}} ratio were consistent with recent model predictions [J. Sehested, J.A.P. Gelten, I.N. Remediakis, H. Bengaard, J.K. Norskov, J. Catal. 223 (2004) 432] over a broad range of environmental conditions. However, exposing the catalysts to severe sintering conditions the loss of nickel surface area is faster than model predictions and the deviation is attributed to a change in the sintering mechanism and nickel removal by nickel-carrier interactions. Surprisingly, alumina-supported Ni particles grow to sizes larger than the particle size of the carrier indicating that the pore diameter does not represent an upper limit for Ni particle growth. The effects of potassium promotion and sulfur poisoning on the rates of sintering were also investigated. No significant effects of the dopants were observed after ageing at ambient pressure. However, at high pressures of steam and hydrogen (31bar and H{sub 2}O:H{sub 2}=10:1) potassium promotion increased the sintering rate relative to that of the unpromoted catalyst. Sulfur also enhances the rate of sintering at high pressures, but the effect of sulfur is less than for potassium. (author)

High hydrogen desorption properties of Mg-based nanocomposite at moderate temperatures: The effects of multiple catalysts in situ formed by adding nickel sulfides/graphene

Science.gov (United States)

Xie, Xiubo; Chen, Ming; Liu, Peng; Shang, Jiaxiang; Liu, Tong

2017-12-01

Nickel sulfides decorated reduced graphene oxide (rGO) has been produced by co-reducing Ni2+ and graphene oxide (GO), and is subsequently ball milled with Mg nanoparticles (NPs) produced by hydrogen plasma metal reaction (HPMR). The nickel sulfides of about 800 nm completely in situ change to MgS, Mg2Ni and Ni multiple catalysts after first hydrogenation/dehydrogenation process at 673 K. The Mg-5wt%NiS/rGO nanocomposite shows the highest hydrogen desorption kinetics and capacity properties, and the catalytic effect order of the additives is NiS/rGO, NiS and rGO. At 573 K, the Mg-NiS/rGO nanocomposite can quickly desorb 3.7 wt% H2 in 10 min and 4.5 wt% H2 in 60 min. The apparent hydrogen absorption and desorption activation energies of the Mg-5wt%NiS/rGO nanocomposite are decreased to 44.47 and 63.02 kJ mol-1, smaller than those of the Mg-5wt%rGO and Mg-5wt%NiS samples. The best hydrogen desorption properties of the Mg-5wt%NiS/rGO nanocomposite can be explained by the synergistic catalytic effects of the highly dispersed MgS, Mg2Ni and Ni catalysts on the rGO sheets, and the more nucleation sites between the catalysts, rGO sheets and Mg matrix.

Pretreatments of porous silica for improving the activity of a nickel-loaded catalyst

Energy Technology Data Exchange (ETDEWEB)

Arai, M.; Ikushima, Y.; Nishiyama, Y.

1986-02-01

Nickel catalysts supported on porous silicas treated with water, ethanol, and 1-butanol were found to be more active than that supported on untreated silica for ethane hydrogenolysis and furan hydrogenation. To elucidate the reason for the activation, some surface properties of the treated silicas were examined. The treatments decreased the surface area and increased the volume of the macropores, the surface density of hydroxyl groups, and the heat of immersion in water per unit surface area. The state of nickel on the support was examined by temperature programed desorption (TPD) of hydrogen, X-ray diffraction (XRD), and scanning electron microscopy/X-ray microanalysis. The dispersion measured by XRD was not appreciably altered by the treatments, but the TPD showed more hydrogen desorbed above 150/sup 0/C from nickel on the treated supports. The activation of nickel by pretreatment of the support was ascribed to the increase of those nickel atoms which dispersed finely over the support by the increased number of surface hydroxyl groups. This was based on the number of hydroxyl groups per unit surface area. The nickel catalyst supported on the pretreated silicas showed greater thermal stability. 16 references, 5 figures, 1 table.

Improving hydrogen storage in Ni-doped carbon nanospheres

Energy Technology Data Exchange (ETDEWEB)

Zubizarreta, L.; Menendez, J.A.; Pis, J.J.; Arenillas, A. [Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo (Spain)

2009-04-15

The effect of nickel distribution and content in Ni-doped carbon nanospheres on hydrogen storage capacity under conditions of moderate temperature and pressure was studied. It was found that the nickel distribution, obtained by using different doping techniques and conditions, has a noticeable influence on hydrogen storage capacity. The samples with the most homogeneous nickel distribution, obtained by pre-oxidising the carbon nanospheres, displayed the highest storage capacity. In addition, storage capacity is influenced by the amount of nickel. It was found a higher storage capacity in samples containing 5 wt.% of Ni. This is due to the greater interactions between the nickel and the support that produce a higher activation of the solid through a spillover effect. (author)

Initial results from an IPv6 Darknet

OpenAIRE

Ronan, John; Ford, Matthew; Stevens, Jonathan

2006-01-01

A darknet is an advertised and routed portion of Internet address space that contains no advertised services. Any traffic observed on a darknet is therefore illegitimate and darknets are useful tools for observing the level of background ‘noise’ on a larger network. Darknets have been used in existing IPv4 networks to help to identify malicious traffic, malware trends, or the consequences of misconfiguration. We have created what may be the world’s first IPv6 darknet to help us observe the ‘n...

Surface modification method of rare earth-nickel hydrogen storage alloy for a battery; Denchiyo kidorui-nikkeru kei suiso kyuzo gokin no hyomen kaishitsu shoriho

Energy Technology Data Exchange (ETDEWEB)

Higashiyama, N.; Kimoto, M.; Matsuura, Y.; Kuroda, Y.; Nogami, M.; Nishio, K.; Saito, T.

1996-07-16

The characteristics of an alkaline battery with hydrogen storage alloy depend significantly on the activity of the used rare earth-nickel hydrogen storage alloy and require an activation process in its manufacturing. However, the previous manufacturing method was found to have a defect that surface modification cannot be uniformly conducted due to a rapid increase of pH of the processing solution during the processing. This invention aims to present a surface modification method to enable to produce uniform surface of the alloy particles with a high activity. In this invention, the rare earth-nickel hydrogen storage alloy is immersed in a buffer solution of pH 1 to 3.6 for a fixed period followed by washing with water or an alkaline solution. The rapid change of pH can be avoided by the use of the buffer solution and the surface of the alloy particles is modified uniformly. The use of the obtained alloy suppresses the increase of the internal pressure in the battery during charging and affords an alkaline battery with a long cycle life and a high performance. 1 fig., 3 tabs.

Stable hydrogen production from ethanol through steam reforming reaction over nickel-containing smectite-derived catalyst.

Science.gov (United States)

Yoshida, Hiroshi; Yamaoka, Ryohei; Arai, Masahiko

2014-12-25

Hydrogen production through steam reforming of ethanol was investigated with conventional supported nickel catalysts and a Ni-containing smectite-derived catalyst. The former is initially active, but significant catalyst deactivation occurs during the reaction due to carbon deposition. Side reactions of the decomposition of CO and CH4 are the main reason for the catalyst deactivation, and these reactions can relatively be suppressed by the use of the Ni-containing smectite. The Ni-containing smectite-derived catalyst contains, after H2 reduction, stable and active Ni nanocrystallites, and as a result, it shows a stable and high catalytic performance for the steam reforming of ethanol, producing H2.

RIPng- A next Generation Routing Protocal (IPv6) | Falaye | Journal ...

African Journals Online (AJOL)

... Information Protocol Next Generation (RIPng) owing to the current depletion rate of IPv4. ... that support the Internet Protocol Version 6 (IPv6).addressing scheme. ... A brief history is given; its various versions are discussed, and detailed ...

Orbital simulation life tests of nickel hydrogen batteries with additional non-eclipse cycles

Science.gov (United States)

Johnson, P. J.; Donley, S. W.; Verrier, D. C.

Nickel-hydrogen battery technology has established itself as the system of choice to provide energy storage on board Earth orbiting satellites. In addition to providing electrical power for the satellite during the periods the satellite's solar arrays are eclipsed by the Earth, applications are evolving (such as ion propulsion) where the battery is required to supplement the power supplied to the spacecraft by the solar panels in order to meet the peak power demands. In this paper, the results of a four-year accelerated life test programme, equivalent to more than 20 years in orbit, are reported. Additional non-eclipse cycles were added to both the eclipse and solstice seasons of each simulated spacecraft year. The results show that the additional discharges do not significantly effect the rates of performance degradation of the batteries.

A paste type negative electrode using a MmNi{sub 5} based hydrogen storage alloy for a nickel-metal hydride (Ni-MH) battery

Energy Technology Data Exchange (ETDEWEB)

Uchida, H.; Matsumoto, T.; Watanabe, S.; Kobayashi, K.; Hoshino, H. [Tokai Univ., Kanagawa (Japan). School of Engineering

2001-07-01

Different conducting materials (nickel, copper, cobalt, graphite) were mixed with a MmNi{sub 5} type hydrogen storage alloy, and negative electrodes for a nickel-metal hydride(Ni-MH) rechargeable battery were prepared and examined with respect to the discharge capacity of the electrodes. The change in the discharge capacity of the electrodes with different conducting materials was measured as a function of the number of electrochemical charge and discharge cycles. From the measurements, the electrodes with cobalt and graphite were found to yield much higher discharge capacities than those with nickel or cobalt. From a comparative discharge measurements for an electrode composed of only cobalt powder without the alloy and an electrode with a mixture of cobalt and the alloy, an appreciable contribution of the cobalt surface to the enhancement of charge and discharge capacities was found. (author)

Design and implementation of an intrusion detection system based on IPv6 protocol

Science.gov (United States)

Liu, Bin; Li, Zhitang; Li, Yao; Li, Zhanchun

2005-11-01

Network intrusion detection systems (NIDS) are important parts of network security architecture. Although many NIDS have been proposed, there is little effort to expand the current set of NIDS to support IPv6 protocol. This paper presents the design and implementation of a Network-based Intrusion Detection System that supports both IPv6 protocol and IPv4 protocol. It characters rules based logging to perform content pattern matching and detect a variety of attacks and probes from IPv4 and IPv6.There are four primary subsystems to make it up: packet capture, packet decoder, detection engine, and logging and alerting subsystem. A new approach to packet capture that combined NAPI with MMAP is proposed in this paper. The test results show that the efficiency of packet capture can be improved significantly by this method. Several new attack tools for IPv6 have been developed for intrusion detection evaluation. Test shows that more than 20 kinds of IPv6 attacks can be detected by this system and it also has a good performance under heavy traffic load.

Study of Supported Nickel Catalysts Prepared by Aqueous Hydrazine Method. Hydrogenating Properties and Hydrogen Storage: Support Effect. Silver Additive Effect; Catalyseurs de nickel supportes prepares par la methode de l'hydrazine aqueuse. Proprietes hydrogenantes et stockage d'hydrogene. Effet du support. Effet de l'ajout d'argent

Energy Technology Data Exchange (ETDEWEB)

Wojcieszak, R

2006-06-15

We have studied Ni or NiAg nano-particles obtained by the reduction of nickel salts (acetate or nitrate) by hydrazine and deposited by simple or EDTA-double impregnation on various supports ({gamma}-Al{sub 2}O{sub 3}, amorphous or crystallized SiO{sub 2}, Nb{sub 2}O{sub 5}, CeO{sub 2} and carbon). Prepared catalysts were characterized by different methods (XRD, XPS, low temperature adsorption and desorption of N{sub 2}, FTIR and FTIR-Pyridine, TEM, STEM, EDS, H{sub 2}-TPR, H{sub 2}-adsorption, H{sub 2}-TPD, isopropanol decomposition) and tested in the gas phase hydrogenation of benzene or as carbon materials in the hydrogen storage at room temperature and high pressure. The catalysts prepared exhibited better dispersion and activity than classical catalysts. TOF's of NiAg/SiO{sub 2} or Ni/carbon catalysts were similar to Pt catalysts in benzene hydrogenation. Differences in support acidity or preparation method and presence of Ag as metal additive play a crucial role in the chemical reduction of Ni by hydrazine and in the final properties of the materials. Ni/carbon catalysts could store significant amounts of hydrogen at room temperature and high pressure (0.53%/30 bars), probably through the hydrogen spillover effect. (author)

IPv6:n käyttöönotto PK-yrityksessä

OpenAIRE

Salonen, Arttu Petteri

2011-01-01

Tämän opinnäytetyön tarkoituksena on selvittää, kuinka IPv6-yhteydet otetaan käyt-töön PK-yrityksessä. Työssä selvitetään minkälaiset vaatimukset IPv6 asettaa lait-teistolle ja minkälaisia käytännön asioita yrityksen täytyy huomioida IPv6:n käyt-töönotossa. Lisäksi työssä on laboratoriosimulaation avulla havainnollistettu eri käyt-töjärjestelmien tukea IPv6:lle ja käyttöönottoon liittyviä reititin- ja osoitekonfiguraati-oita. Käyttöönoton lisäksi opinnäytetyössä esitellään IPv6-protokoll...

Cermet sintering on the oase of molybdenum, nickel, aluminium oxide in dry and wet hydrogen medium

International Nuclear Information System (INIS)

Fedotov, A.V.; Lutskaya, E.Eh.

1985-01-01

Cermet sintering on the base of molybdenum, nickel and aluminium oxide in dry and wer hydrogen medium is studied. It is stated that presence of water vapours permits to decrease sintering temperature of molybdenum containing cermets and to prepare dense nickeliferous cermets. Cermet density can he rather high at final stages of sintering that is probably conditioned by decrease of growth rate of corundum crystals. Pressing pressure activates cermet siptering at intermediate stages and it is low effective at finite stages of condensation. Constancy of relative reduction of void volume is preserved only at final stages of sintering

Hydrogen-plasticity interactions in nickel and nickel base alloys

International Nuclear Information System (INIS)

Girardin, G.

2004-03-01

We evaluate the different contributions of the hydrogen-dislocation interactions to the plasticity of fcc materials in order to feed predictive models of stress corrosion cracking. Static strain ageing experiments are used to quantify the hardening contribution of solute drag by dislocations to the flow stress. We demonstrate the role of hydrogen transport by dislocations on the fracture mechanism. We model the influence of the screening of the elastic field of dislocations by hydrogen on elementary plasticity mechanisms and we conclude that the decrease of the cross slip ability arises from the combined action of elastic and core effects. The testing of single crystals shows that the major effect is on the cross slip mechanism. Tensile tests on polycrystals enlighten the diversity of macroscopic responses observed in alloys. (author)

Exchange of deuterium with hydrogen of zeolite catalyst surface

International Nuclear Information System (INIS)

Minachev, Kh.M.; Dmitriev, R.V.; Penchev, V.; Kanazirev, V.; Minchev, Kh.; Kasimov, Ch.K.; Bylgarska Akademiya na Naukite, Sofia. Inst. za Obshta i Organichna Khimiya; AN Azerbajdzhanskoj SSR, Baku. Inst. Neftekhimicheskikh Protsessov)

1981-01-01

Isotope heteromolecular exchange of hydrogen on the reduced nickel-containing zeolites takes places at the temperatures above 100 deg and it is controlled by activated hydrogen transfer from metal particles on the substrate surface. High-temperature redox treatment of nickel-containing zeolites results in the formation of large nickel crystallites on zeolite external faces. The rest part of nickel remains in zeolite pores and conditions a high promoting effect in the exchange reaction. Catalytic activity of reduced zeolites NiCaNaY in toluene disproportionation increases considerably only in the cases when nickel is introduced into zeolite by means of ion exchange. Close spatial location of nickel particles and OH groups promotes the procedure of both isotope exchange and disproportionation of toluene [ru

Hydrogen embrittlement: the game changing factor in the applicability of nickel alloys in oilfield technology

Science.gov (United States)

Sarmiento Klapper, Helmuth; Klöwer, Jutta; Gosheva, Olesya

2017-06-01

Precipitation hardenable (PH) nickel (Ni) alloys are often the most reliable engineering materials for demanding oilfield upstream and subsea applications especially in deep sour wells. Despite their superior corrosion resistance and mechanical properties over a broad range of temperatures, the applicability of PH Ni alloys has been questioned due to their susceptibility to hydrogen embrittlement (HE), as confirmed in documented failures of components in upstream applications. While extensive work has been done in recent years to develop testing methodologies for benchmarking PH Ni alloys in terms of their HE susceptibility, limited scientific research has been conducted to achieve improved foundational knowledge about the role of microstructural particularities in these alloys on their mechanical behaviour in environments promoting hydrogen uptake. Precipitates such as the γ', γ'' and δ-phase are well known for defining the mechanical and chemical properties of these alloys. To elucidate the effect of precipitates in the microstructure of the oil-patch PH Ni alloy 718 on its HE susceptibility, slow strain rate tests under continuous hydrogen charging were conducted on material after several different age-hardening treatments. By correlating the obtained results with those from the microstructural and fractographic characterization, it was concluded that HE susceptibility of oil-patch alloy 718 is strongly influenced by the amount and size of precipitates such as the γ' and γ'' as well as the δ-phase rather than by the strength level only. In addition, several HE mechanisms including hydrogen-enhanced decohesion and hydrogen-enhanced local plasticity were observed taking place on oil-patch alloy 718, depending upon the characteristics of these phases when present in the microstructure. This article is part of the themed issue 'The challenges of hydrogen and metals'.

Solubility of nickel ferrite (NiFe2O4) from 100 to 200 deg. C

International Nuclear Information System (INIS)

Bellefleur, Alexandre; Bachet, Martin; Benezeth, Pascale; Schott, Jacques

2012-09-01

The solubility of nickel ferrite was measured in a Hydrogen-Electrode Concentration Cell (HECC) at temperatures of 100 deg. C, 150 deg. C and 200 deg. C and pH between 4 and 5.25. The experimental solution was composed of HCl and NaCl (0.1 mol.L -1 ). Based on other studies ([1,2]), pure nickel ferrite was experimentally synthesized by calcination of a mixture of hematite Fe 2 O 3 and bunsenite NiO in molten salts at 1000 deg. C for 15 hours in air. The so obtained powder was fully characterized. The Hydrogen-Electrode Concentration cell has been described in [3]. It allowed us to run solubility experiments up to 250 deg. C with an in-situ pH measurement. To avoid reduction of the solid phase to metallic nickel, a hydrogen/argon mixture was used instead of pure hydrogen. Consequently, the equilibration time for the electrodes was longer than with pure hydrogen. Eight samples were taken on a 70 days period. After the experiments, the powder showed no significant XRD evidence of Ni (II) reduction. Nickel concentration was measured by atomic absorption spectroscopy and iron concentration was measured by UV spectroscopy. The protocol has been designed to be able to measure both dissolved Fe (II) and total iron. The nickel solubility of nickel ferrite was slightly lower than the solubility of nickel oxide in close experimental conditions [3]. Dissolved iron was mainly ferrous and the solution was under-saturated relative to both hematite and magnetite. The nickel/iron ratio indicated a non-stoichiometric dissolution. The solubility measurements were compared with equilibrium calculations using the MULTEQ database. [1] Hayashi et al (1980) J. Materials Sci. 15, 1491-1497. [2] Ziemniak et al (2007) J. Physics and Chem. of Solids. 68,10-21. [3] EPRI Report 1003155 (2002). (authors)

Towards an Ultrasonic Guided Wave Procedure for Health Monitoring of Composite Vessels: Application to Hydrogen-Powered Aircraft.

Science.gov (United States)

Yaacoubi, Slah; McKeon, Peter; Ke, Weina; Declercq, Nico F; Dahmene, Fethi

2017-09-19

This paper presents an overview and description of the approach to be used to investigate the behavior and the defect sensitivity of various ultrasonic guided wave (UGW) modes propagating specifically in composite cylindrical vessels in the framework of the safety of hydrogen energy transportation such as hydrogen-powered aircrafts. These structures which consist of thick and multi-layer composites are envisioned for housing hydrogen gas at high pressures. Due to safety concerns associated with a weakened structure, structural health monitoring techniques are needed. A procedure for optimizing damage detection in these structural types is presented. It is shown that a finite element method can help identify useful experimental parameters including frequency range, excitation type, and receiver placement.

A nanostructural study of Raney-type nickel catalysts

NARCIS (Netherlands)

Devred, F.

2004-01-01

Raney-type nickel catalysts have been applied in commercial hydrogenation reactions for decades. They are relatively cheap and have proven to be very efficient in hydrogenation. The preparation process is relatively simple, but it appears that many parameters have an influence on the performance of

Decay of Sabin inactivated poliovirus vaccine (IPV-boosted poliovirus antibodies

Directory of Open Access Journals (Sweden)

Sonia Resik

2015-01-01

Conclusion: The decay of poliovirus antibodies over a 21–22-month period was similar regardless of the type of booster vaccine used, suggesting the scientific data of Salk IPV long-term persistence and decay may be broadly applicable to Sabin IPV.

The use of stainless steel and nickel alloys as low-cost cathodes in microbial electrolysis cells

KAUST Repository

Selembo, Priscilla A.

2009-05-01

Microbial electrolysis cells (MECs) are used to produce hydrogen gas from the current generated by bacteria, but low-cost alternatives are needed to typical cathode materials (carbon cloth, platinum and Nafion™). Stainless steel A286 was superior to platinum sheet metal in terms of cathodic hydrogen recovery (61% vs. 47%), overall energy recovery (46% vs. 35%), and maximum volumetric hydrogen production rate (1.5 m3 m-3 day-1 vs. 0.68 m3 m-3 day-1) at an applied voltage of 0.9 V. Nickel 625 was better than other nickel alloys, but it did not perform as well as SS A625. The relative ranking of these materials in MEC tests was in agreement with cyclic voltammetry studies. Performance of the stainless steel and nickel cathodes was further increased, even at a lower applied voltage (0.6 V), by electrodepositing a nickel oxide layer onto the sheet metal (cathodic hydrogen recovery, 52%, overall energy recovery, 48%; maximum volumetric hydrogen production rate, 0.76 m3 m-3 day-1). However, performance of the nickel oxide cathodes decreased over time due to a reduction in mechanical stability of the oxides (based on SEM-EDS analysis). These results demonstrate that non-precious metal cathodes can be used in MECs to achieve hydrogen gas production rates better than those obtained with platinum. © 2009 Elsevier B.V. All rights reserved.

The use of stainless steel and nickel alloys as low-cost cathodes in microbial electrolysis cells

KAUST Repository

Selembo, Priscilla A.; Merrill, Mathew D.; Logan, Bruce E.

2009-01-01

Microbial electrolysis cells (MECs) are used to produce hydrogen gas from the current generated by bacteria, but low-cost alternatives are needed to typical cathode materials (carbon cloth, platinum and Nafion™). Stainless steel A286 was superior to platinum sheet metal in terms of cathodic hydrogen recovery (61% vs. 47%), overall energy recovery (46% vs. 35%), and maximum volumetric hydrogen production rate (1.5 m3 m-3 day-1 vs. 0.68 m3 m-3 day-1) at an applied voltage of 0.9 V. Nickel 625 was better than other nickel alloys, but it did not perform as well as SS A625. The relative ranking of these materials in MEC tests was in agreement with cyclic voltammetry studies. Performance of the stainless steel and nickel cathodes was further increased, even at a lower applied voltage (0.6 V), by electrodepositing a nickel oxide layer onto the sheet metal (cathodic hydrogen recovery, 52%, overall energy recovery, 48%; maximum volumetric hydrogen production rate, 0.76 m3 m-3 day-1). However, performance of the nickel oxide cathodes decreased over time due to a reduction in mechanical stability of the oxides (based on SEM-EDS analysis). These results demonstrate that non-precious metal cathodes can be used in MECs to achieve hydrogen gas production rates better than those obtained with platinum. © 2009 Elsevier B.V. All rights reserved.

Analysis of the dose-sparing effect of adjuvanted Sabin-inactivated poliovirus vaccine (sIPV).

Science.gov (United States)

Li, Zhuofan; Ding, Wenting; Guo, Qi; Liu, Ze; Zhu, Zhe; Song, Shaohui; Li, Weidong; Liao, Guoyang

2018-03-30

Sabin-based inactivated poliovirus vaccine(sIPV) is gradually replacing live-attenuated oral polio vaccine(OPV). Sabin-inactivated poliovirus vaccine(sIPV) has played a vital role in reducing economic burden of poliomyelitis and maintaining appropriate antibody levels in the population. However, due to its high cost and limited manufacturing capacity, sIPV cannot reach its full potential for global poliovirus eradication in developing countries. Therefore, to address this situation, we designed this study to evaluate the dose-sparing effects of AS03, CpG oligodeoxynucleotides (CpG-ODN) and polyinosinic:polycytidylic acid (PolyI:C) admixed with sIPV in rats. Our results showed that a combination of 1/4-dose sIPV adjuvanted with AS03 or AS03 with BW006 provides a seroconversion rate similar to that of full-dose sIPV without adjuvant and that, this rate is 5-fold higher than that of 1/4-dose sIPV without adjuvant after the first immunization. The combination of AS03 or AS03 with BW006 as an adjuvant effectively reduced sIPV dose by at least 4-fold and induced both humoral and cellular immune responses. Therefore, our study revealed that the combination of AS03 or AS03 with BW006 is a promising adjuvant for sIPV development.

RENEW: a real-time and effective network emulator of windows for IPv6

Science.gov (United States)

Zhao, Bing; Jin, Zhigang; Shu, Yantai; Li, Yu; Cen, Dan

2007-09-01

Although IPv4 is still working, IPv6 is considered as the backbone and characteristic of the NGI. With the development of Internet, new protocols and network equipments are required to develop. It is necessary to test the new protocols and network equipments extensively before deployment. This paper proposes the design and implementation of RENEW, a useable and accurate network emulator which supports both IPv4 and IPv6 protocols. Besides, it also works on Windows platform. In our IPv6 testbed, we use RENEW to emulate various network characteristics and conditions including bandwidth, delay packet loss and jitter. Compared with the expected values, results are acceptable. Through implementation and experimentation study, we have shown that RENEW does provide the real-time control and change on the parameters of IPv6 network conditions effectively and expediently on Windows. It also gives enough accuracy and more satisfactory convenience to the development and test work for the new protocols.

Treatment method of hydrogen storage alloy for battery; Denchiyo suiso kyuzo gokin no shori hoho

Energy Technology Data Exchange (ETDEWEB)

Negi, Y.; Kaminaka, H.; Nagata, T.; Takeshita, Y.

1997-04-04

A nickel-hydrogen battery using a hydrogen storage alloy takes considerably long time for the initial activation treatment after the assembly of the battery. In this invention, a hydrogen storage alloy containing nickel is immersed in an aqueous acid solution or an aqueous alkaline solution and washed with a solution containing a complexing agent to form a nickel complex by a reaction with Ni(OH)2 in a concentration of 10{sup -6} to 10{sup -1} followed by washing with water. By using this method, hydroxides, particularly, Ni(OH)2 deposited on the alloy surface on the treatment of the hydrogen storage alloy with aqueous acid or alkaline solution can be removed efficiently to afford the hydrogen storage alloy with a high initial activity. The hydrogen storage alloy which is the object of this treatment method is AB5 type and AB2 type alloy used for a nickel-hydrogen battery and an alloy composed of nickel is particularly preferable. The complexing agent is selected from ammonia, ethylenediamine and cyanides. 2 figs., 6 tabs.

Empirical Profiling of Cold Hydrogen Plumes Formed from Venting Of LH2 Storage Vessels: Preprint

Energy Technology Data Exchange (ETDEWEB)

Buttner, William J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Rivkin, Carl H [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Schmidt, Kara [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hartmann, Kevin S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wright, Hannah [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Weidner, Eveline [Joint Research Centre, Petten, the Netherlands; Ciotti, Michael [H2 Fueling and CIP Markets Engineering

2017-11-16

Liquid hydrogen (LH2) storage is a viable approach to assuring sufficient hydrogen capacity at commercial fuelling stations. Presently, LH2 is produced at remote facilities and then transported to the end-use site by road vehicles (i.e., LH2 tanker trucks). Venting of hydrogen to depressurize the transport storage tank is a routine part of the LH2 delivery process. The behaviour of cold hydrogen plumes has not been well-characterized because empirical field data is essentially non-existent. The NFPA 2 Hydrogen Storage Safety Task Group, which consists of hydrogen producers, safety experts, and CFD modellers, has identified the lack of understanding of hydrogen dispersion during LH2 venting of storage vessel as a critical gap for establishing safety distances at LH2 facilities, especially commercial hydrogen fuelling stations. To address this need, the NREL sensor laboratory, in collaboration with the NFPA 2 Safety Task Group developed the Cold Hydrogen Plume Analyzer to empirically characterize the hydrogen plume formed during LH2 storage tank venting. A prototype Analyzer was developed and field-deployed at an actual LH2 venting operation with critical findings that included: - H2 being detected as much as 2 m lower than the release point, which is not predicted by existing models - A small and inconsistent correlation between oxygen depletion and the hydrogen concentration - A negligible to non-existent correlation between in-situ temperature and the hydrogen concentration The Analyzer is currently being upgraded for enhanced metrological capabilities including improved real-time spatial and temporal profiling of the plume and tracking of prevailing weather conditions. Additional deployments are planned to monitor plume behaviour under different wind, humidity, and temperatures. This data will be shared with the NFPA 2 Safety Task Group and ultimately will be used support theoretical models and code requirements prescribed in NFPA 2.

Innovative IPV from attenuated Sabin poliovirus or newly designed alternative seed strains.

Science.gov (United States)

Hamidi, Ahd; Bakker, Wilfried A M

2012-11-01

This article gives an overview of the patent literature related to innovative inactivated polio vaccine (i-IPV) based on using Sabin poliovirus strains and newly developed alternative recombinant poliovirus strains. This innovative approach for IPV manufacturing is considered to attribute to the requirement for affordable IPV in the post-polio-eradication era, which is on the horizon. Although IPV is a well-established vaccine, the number of patent applications in this field was seen to have significantly increased in the past decade. Currently, regular IPV appears to be too expensive for universal use. Future affordability may be achieved by using alternative cell lines, alternative virus seed strains, improved and optimized processes, dose sparing, or the use of adjuvants. A relatively short-term option to achieve cost-price reduction is to work on regular IPV, using wild-type poliovirus strains, or on Sabin-IPV, based on using attenuated poliovirus strains. This price reduction can be achieved by introducing efficiency in processing. There are also multiple opportunities to work on dose sparing, for example, by using adjuvants or fractional doses. Renewed interest in this field was clearly reflected in the number and diversity of patent applications. In a later stage, several innovative approaches may become even more attractive, for example the use of recombinant virus strains or even a totally synthetic vaccine. Currently, such work is mainly carried out by research institutes and universities and therefore clinical data are not available.

Electroactivity of cobalt and nickel glyoximes with regard to the electro-reduction of protons into molecular hydrogen in acidic media

Energy Technology Data Exchange (ETDEWEB)

Pantani, O.; Anxolabehere-Mallart, E.; Aukauloo, A. [Equipe de Chimie Inorganique, Institut de Chimie Moleculaire et des Materiaux d' Orsay, UMR 8182, Universite Paris Sud, bat 420, 91405 Orsay Cedex (France); Millet, P. [Equipe de Physico-Chimie de l' Etat Solide, Institut de Chimie Moleculaire et des Materiaux d' Orsay, UMR 8182, Universite Paris Sud, bat 420, 91405 Orsay Cedex (France)

2007-01-15

Water electrolysis is a key technological process for the production of hydrogen and the storage of intermittent and renewable energy sources. For domestic applications, the proton exchange membrane (PEM) process provides a safe and efficient way to split water into molecular hydrogen and oxygen but this technology, which requires platinum family electro-catalysts, remains too expensive. Molecular chemistry offers new opportunities for synthesizing alternative low-cost compounds, sufficiently stable in strong acidic media. In this paper, results obtained with different nickel and cobalt glyoximes are presented. They have been chemically (using UV-visible spectroscopy) and electrochemically (using cyclic voltammetry and spectro-electrochemistry) characterized. Their ability to electroreduce protons into molecular hydrogen from aqueous acidic solutions is discussed, the compounds being either dissolved in solution or immobilized at the surface of a solid electrode using recast Nafion{sup (R)} films in view of PEM applications. (author)

Towards an Ultrasonic Guided Wave Procedure for Health Monitoring of Composite Vessels: Application to Hydrogen-Powered Aircraft

Directory of Open Access Journals (Sweden)

Slah Yaacoubi

2017-09-01

Full Text Available This paper presents an overview and description of the approach to be used to investigate the behavior and the defect sensitivity of various ultrasonic guided wave (UGW modes propagating specifically in composite cylindrical vessels in the framework of the safety of hydrogen energy transportation such as hydrogen-powered aircrafts. These structures which consist of thick and multi-layer composites are envisioned for housing hydrogen gas at high pressures. Due to safety concerns associated with a weakened structure, structural health monitoring techniques are needed. A procedure for optimizing damage detection in these structural types is presented. It is shown that a finite element method can help identify useful experimental parameters including frequency range, excitation type, and receiver placement.

MULTI-LINK SUPPORT FOR IPV6 NETWORKS

Directory of Open Access Journals (Sweden)

Cüneyt Akınlar

2016-03-01

Full Text Available IPv6 ağ konfigürasyonu için genel pratik ağ üzerindeki her fiziksel bağ için ayrı bir altağ öneki atamaktır. Bu uygulama hem birden fazla ağ öneki gereksimine sebep olur, hem de elle yönetim ve konfigürasyon gerektirir. Buna alternatif konfigürasyon yöntemi bütün bağları IPv6 seviyesinde bir köprü ile bağlamak ve bu sayede bütün ağ için tek bir ağ öneki ataması yapmaktır. Bu metoda çoklu-bağ öneki ismi verilir. Bu makalede IPv6 ağları için çoklu-bağ öneki oto-konfigürasyonu konusu ele alınmıştır. Öncelikle tek yönlendiricili ağlar için coklu-bağ desteğinin nasıl gerçekleneceği tarif edilmiş, daha sonra bu yöntemin çok yönlendiricili ağlara nasıl uygulanacağı anlatılmıştır. Önerilen oto-konfigürasyon yöntemleri standart alıcı otokonfigürasyon protokollerini tamamlamakta ve IPv6 ağlarının yaygın kurulum ve kullanımları için gerekli tak-çalıştır metodolojine olanak sağlamaktadır

APT characterization of high nickel RPV steels

International Nuclear Information System (INIS)

Miller, M.K.; Russell, K.F

2004-01-01

Full text: The microstructures of several high nickel content pressure vessel steels have been characterized by atom probe tomography. The purposes of this study were to investigate the influence of high nickel levels on the response to neutron irradiation of high and low copper pressure vessel steels and to establish whether any additional phases were present after neutron irradiation. The nickel levels in these steels were at least twice that typically found in Western pressure vessel steels. Two different types of pressure vessel steels with low and high copper contents were selected for this study. The first set of alloys was low copper (∼0.05% Cu) base (15Ch2NMFAA) and weld (12Ch2N2MAA) materials used in a VVER-1000 reactor. The composition of the lower nickel VVER-1000 base material was Fe- 0.17 wt% C, 0.30% Si, 0.46% Mn, 2.2% Cr, 1.26% Ni, 0.05% Cu, 0.01% S, 0.008% P, 0.10% V and 0.50% Mo. The composition of the higher nickel VVER-1000 weld material was Fe- 0.06 wt % C, 0.33% Si, 0.80% Mn, 1.8% Cr, 1.78% Ni, 0.07% Cu, 0.009% S, 0.005% P, and 0.63% Mo. The VVER-1000 steels were irradiated in the HSSI Program's irradiation facilities at the University of Michigan, Ford Nuclear Reactor at a temperature of 288 o C for 2,137 h at an average flux of 7.08 x 10 11 cm 2 s -1 for a fluence of 5.45 x 10 18 n cm -2 (E >1 MeV) and for 5,340 h at an average flux of 4.33 x 10 11 cm -2 s -1 for a fluence of 8.32 x 10 1 28 n cm -2 (E >1 MeV). Therefore, the total fluence was 1.38 x 10 19 n cm -2 (E >1 MeV). The second type of pressure vessel steel was a high copper (0.20% Cu) weld from the Palisades reactor. The average composition of the Palisades weld was Fe- 0.11 wt% C, 0.18% Si, 1.27% Mn, 0.04% Cr, 1.20% Ni, 0.20% Cu, 0.017% S, 0.014% P, 0.003% V and 0.55% Mn. The Palisades weld, designated weldment 'B' from weld heat 34B009, was irradiated at a temperature of 288 o C and a flux of ∼7 x 10 11 cm -2 s -1 to a fast fluence of 1.4 x 10 19 n cm -2 (E >1 MeV). These three

CONFIGURACIÓN DE UNA RED DE NUEVA GENERACIÓN PARA CONECTIVIDAD CON INTERNET RESPALDADO POR UN SERVICIO DNS CON SOPORTE PARA IPV4 E IPV6.

Directory of Open Access Journals (Sweden)

Carlos Andrés Martínez

2012-05-01

Full Text Available Se presentan las características mas representativas de la implementación de la isla ipv6 del centro de computación de alto desempeño CECAD, realizando pruebas de conexión y desempeño en el tráfico interno con las subredes de la Universidad Distrital y posteriormente con su conexión a Internet a través del protocolo NAT-PT secundado por un servidor de nombres de domino recursivo como base de conectividad y soporte sobre estructuras Ipv4 e Ipv6 nativas.

Special tests and destructive physical analyses as used by the Aerospace Corporation with nickel-hydrogen cells

Science.gov (United States)

Zimmerman, A. H.; Quinzio, M. V.; Thaller, L. H.

1992-01-01

The destructive physical analysis (DPA) of electrochemical devices is an important part of the overall test. Specific tests were developed to investigate the degradation mode or the failure mechanism that surfaces during the course of a cell being assembled, acceptance tested, and life-cycle tested. The tests that have been developed are peculiar to the cell chemistry under investigation. Tests are often developed by an individual or group of researchers as a result of their particular interest in an unresolved failure mechanism or degradation mode. A series of production, operational, and storage issues that were addressed by the Electrochemistry Group at The Aerospace Corporation are addressed. As a result of these investigations, as well as associated research studies carried out to develop a clearer understanding of the nickel oxyhydroxide electrode, a series of unique and useful specialized tests were developed. Some of these special tests were assembled to describe the methods that were found to be particularly useful in resolving a wide spectrum of manufacturing, operational, and storage issues related to nickel-hydrogen cells. The general methodology of these tests is given here with references listed to provide the reader with a more detailed understanding of the tests. The tests are classified according to the sequencing, starting with the impregnation of the nickel plaque material and culminating with the storage of completed cells. The details of the wet chemical procedures that were found to be useful because of their accuracy and reproducibility are given. The equations used to make the appropriate calculations are listed.

Analisis Kematangan Implementasi Internet Protocol versi 6 (IPv6 di Indonesia dengan Interim Maturity Level (IML

Directory of Open Access Journals (Sweden)

Riza Azmi

2012-12-01

Full Text Available Cepat atau lambat, IPv6 akan menggantikan IPv4 dalam penomoran internet. Hal ini dikarenakan IANA telah mengalokasikan blok IPv4 terakhirnya pada Januari 2011 lalu. Pesatnya permintaan terhadap IP ini dikarenakan boomingnya .com sejak tahun 2000. Dengan habisnya IPv4, terdapat beberapa metode untuk melakukan migrasi ke peenomoran baru IPv6. Terkait dengan hal tersebut, penelitian ini mencoba mengukur tingkat kematangan beberapa penyelenggara jasa internet di Indonesia dalam hal implementasi IPv6 dengan menggunakan konsep Capability Maturity Model for IPv6 Implementation. Metode assesmen yang dilakukan dengan Interim Maturity Level, yaitu dengan memberikan seperangkat pertanyaan yang diisi sendiri oleh penyelenggara jasa internet. Hasil yang didapat adalah, sebagian besar penyelenggara internet masih berada pada Level 2 – Savvy.

Deployment of 464XLAT (RFC6877) alongside IPv6-only CPU resources at WLCG sites

Science.gov (United States)

Froy, T. S.; Traynor, D. P.; Walker, C. J.

2017-10-01

IPv4 is now officially deprecated by the IETF. A significant amount of effort has already been expended by the HEPiX IPv6 Working Group on testing dual-stacked hosts and IPv6-only CPU resources. Dual-stack adds complexity and administrative overhead to sites that may already be starved of resource. This has resulted in a very slow uptake of IPv6 from WLCG sites. 464XLAT (RFC6877) is intended for IPv6 single-stack environments that require the ability to communicate with IPv4-only endpoints. This paper will present a deployment strategy for 464XLAT, operational experiences of using 464XLAT in production at a WLCG site and important information to consider prior to deploying 464XLAT.

Special features of nickel-molybdenum alloy electrodeposition onto screen-type cathodes

International Nuclear Information System (INIS)

Aleksandrova, G.S.; Varypaev, V.N.

1982-01-01

Electrolytic nickel-molybdenum alloy, which has a rather low hydrogen overpotential and high corrosion resistance, is of interest as cathode material in industrial electrolysis. Screen-type electrodes with a nickel-molybdenum coating can be used as nonconsumable cathodes in water-activated magnesium-alloy batteries

IPv6 ネットワークの構築

OpenAIRE

山田, 純一

2008-01-01

富山大学では2006年，国立情報学研究所より，IPｖ6(Internet Protocol Version 6)の割り当てが承認された。IPv6は現在使用されているIPアドレスであるIPv4(Internet Protocol Version 4)の枯渇問題を解消するために開発されたIPアドレスである。このIPv6が誕生してから数年，今さらではあるがローカル環境にてIPv6ネットワークを構築し，検証を行ったので，ここに報告する。

Safety and immunogenicity of a primary series of Sabin-IPV with and without aluminum hydroxide in infants.

Science.gov (United States)

Verdijk, Pauline; Rots, Nynke Y; van Oijen, Monique G C T; Weldon, William C; Oberste, M Steven; Okayasu, Hiromasa; Sutter, Roland W; Bakker, Wilfried A M

2014-09-03

An inactivated poliovirus vaccine (IPV) based on attenuated poliovirus strains (Sabin-1, -2 and -3) was developed for technology transfer to manufacturers in low- and middle-income countries in the context of the global polio eradication initiative. Safety and immunogenicity of Sabin-IPV (sIPV) was evaluated in a double-blind, randomized, controlled, dose-escalation trial in the target population. Healthy infants (n=20/group) aged 56-63 days, received a primary series of three intramuscular injections with low-, middle- or high-dose sIPV with or without aluminum hydroxide or with the conventional IPV based on wild poliovirus strains (wIPV). Virus-neutralizing titers against both Sabin and wild poliovirus strains were determined before and 28 days after three vaccinations. The incidence of local and systemic reactions was comparable with the wIPV. Seroconversion rates after three vaccinations were 100% for type 2 and type 3 polioviruses (both Sabin and wild strains) and 95-100% for type 1 polioviruses. Median titers were high in all groups. Titers were well above the log2(titer) correlated with protection (=3) for all groups. Median titers for Sabin-2 were 9.3 (range 6.8-11.5) in the low-dose sIPV group, 9.2 (range 6.8-10.2) in the low-dose adjuvanted sIPV group and 9.8 (range 5.5-15.0) in the wIPV group, Median titers against MEF-1 (wild poliovirus type 2) were 8.2 (range 4.8-10.8) in the low-dose sIPV group, 7.3 (range 4.5-10.2) in the low-dose adjuvanted Sabin-IPV group and 10.3 (range 8.5-17.0) in the wIPV group. For all poliovirus types the median titers increased with increasing dose levels. sIPV and sIPV adjuvanted with aluminum hydroxide were immunogenic and safe at all dose levels, and comparable with the wIPV. EudraCTnr: 2011-003792-11, NCT01709071. Copyright © 2014. Published by Elsevier Ltd.

Optimization in Mobile IPv6 with Dynamic DNS

OpenAIRE

塩津, 達郎

2005-01-01

機器の高性能化により、モバイル端末においてもインターネットを利用した様々なアプリケーションを利用する要求が増え、無線通信環境の充実により、モバイル端末への通信を継続する仕組みが求められるようになった。 移動中の継続的な通信を可能とする技術の一つとして Mobile IPv6 がある。Mobile IPv6 にり、端末が移動しても通信を継続できる移動透過性が提供される。この移動透過性を実現するために、Mobile IPv6 では移動する端末とその端末と通信をしている端末の仲介役となる Home Agent が必要になる。ところが、仲介役となる必要のない場合でも Home Agent が仲介役として動き、無駄なパケットがインターネット上に流れてしまう。 本論文では、Mobile IPv6 という技術に加えて、Dynamic DNS という技術を用いて、Mobile IPv6 ネットワークの最適化を行う手法を提案し、性能評価を行った。...

Carbon-Nanotube-Supported Bio-Inspired Nickel Catalyst and Its Integration in Hybrid Hydrogen/Air Fuel Cells

Energy Technology Data Exchange (ETDEWEB)

Gentil, Solène [Univ. Grenoble Alpes, CNRS, DCM UMR 5250, 38000 Grenoble France; Laboratoire de Chimie et Biologie des Métaux, Univ. Grenoble Alpes, CNRS UMR5249, CEA, 38000 Grenoble France; Lalaoui, Noémie [Univ. Grenoble Alpes, CNRS, DCM UMR 5250, 38000 Grenoble France; Dutta, Arnab [Pacific Northwest National Laboratory, Richland WA 99532 USA; Current address: Chemistry Department, IIT Gandhinagar, Gujarat 382355 India; Nedellec, Yannig [Univ. Grenoble Alpes, CNRS, DCM UMR 5250, 38000 Grenoble France; Cosnier, Serge [Univ. Grenoble Alpes, CNRS, DCM UMR 5250, 38000 Grenoble France; Shaw, Wendy J. [Pacific Northwest National Laboratory, Richland WA 99532 USA; Artero, Vincent [Laboratoire de Chimie et Biologie des Métaux, Univ. Grenoble Alpes, CNRS UMR5249, CEA, 38000 Grenoble France; Le Goff, Alan [Univ. Grenoble Alpes, CNRS, DCM UMR 5250, 38000 Grenoble France

2017-01-12

A biomimetic nickel bis-diphosphine complex incorporating the amino-acid arginine in the outer coordination sphere, was immobilized on modified single-wall carbon nanotubes (SWCNTs) through electrostatic interactions. The sur-face-confined catalyst is characterized by a reversible 2-electron/2-proton redox process at potentials close to the equibrium potential of the H+/H2 couple. Consequently, the functionalized redox nanomaterial exhibits reversible electrocatalytic activity for the H2/2H+ interconversion over a broad range of pH. This system exhibits catalytic bias, analogous to hydrogenases, resulting in high turnover frequencies at low overpotentials for electrocatalytic H2 oxida-tion between pH 0 and 7. This allowed integrating such bio-inspired nanomaterial together with a multicopper oxi-dase at the cathode side in a hybrid bioinspired/enzymatic hydrogen fuel cell. This device delivers ~2 mW cm–2 with an open-circuit voltage of 1.0 V at room temperature and pH 5, which sets a new efficiency record for a bio-related hydrogen fuel cell with base metal catalysts.

Manfacturers, service providers gear up for the next Big Thing IPV6

CERN Multimedia

2003-01-01

"IPv6 apparently is the heir apparent to the current communication standard, IPv4, and communications equipment manufacturers are taking this into consideration as they design their next-generation gear" (1/2 page).

Tungsen--nickel--cobalt alloy and method of producing same

International Nuclear Information System (INIS)

Dickinson, J.M.; Riley, R.E.

1977-01-01

An improved tungsten alloy having a tungsten content of approximately 95 weight percent, a nickel content of about 3 weight percent, and the balance being cobalt of about 2 weight percent is described. A method for producing this tungsten--nickel--cobalt alloy is further described and comprises coating the tungsten particles with a nickel--cobalt alloy, pressing the coated particles into a compact shape, heating the compact in hydrogen to a temperature in the range of 1400 0 C and holding at this elevated temperature for a period of about 2 hours, increasing this elevated temperature to about 1500 0 C and holding for 1 hour at this temperature, cooling to about 1200 0 C and replacing the hydrogen atmosphere with an inert argon atmosphere while maintaining this elevated temperature for a period of about 1 / 2 hour, and cooling the resulting alloy to room temperature in this argon atmosphere

Life cycle test results of a bipolar nickel hydrogen battery

Science.gov (United States)

Cataldo, R. L.

1985-01-01

A history is given of low Earth orbit (LEO) laboratory test data on a 6.5 ampere-hour bipolar nickel hydrogen battery designed and built at the NASA Lewis Research Center. The bipolar concept is a means of achieving the goal of producing an acceptable battery, of higher energy density, able to withstand the demands of low-Earth-orbit regimes. Over 4100 LEO cycles were established on a ten cell battery. It seems that any perturbation on normal cycling effects the cells performance. Explanations and theories of the battery's behavior are varied and widespread among those closely associated with it. Deep discharging does provide a reconditioning effect and further experimentation is planned in this area. The battery watt-hour efficiency is about 75 percent and the time averaged, discharge voltage is about 1.26 volts for all cells at both the C/4 and LEO rate. Since a significant portion of the electrode capacity has degraded, the LEO cycle discharges are approaching depths of 90 to 100 percent of the high rate capacity. Therefore, the low end-of-discharge voltages occur precipitously after the knee of the discharge curve and is more an indication of electrode capacity and is a lesser indicator of overall cell performance.

Something From Nothing (There): Collecting Global IPv6 Datasets from DNS

NARCIS (Netherlands)

Fiebig, T.; Borgolte, Kevin; Hao, Shuang; Kruegel, Christopher; Vigna, Giovanny; Spring, Neil; Riley, George F.

2017-01-01

Current large-scale IPv6 studies mostly rely on non-public datasets, asmost public datasets are domain specific. For instance, traceroute-based datasetsare biased toward network equipment. In this paper, we present a new methodologyto collect IPv6 address datasets that does not require access to

Effect study of the support in nickel and cobalt catalysts for obtaining hydrogen from ethanol steam reforming

International Nuclear Information System (INIS)

Silva, Sirlane Gomes da

2013-01-01

A range of oxide-supported metal catalysts have been investigated for the steam reforming of ethanol for the production of hydrogen and subsequent application in fuel cells. The catalysts were synthesized by the co-precipitation and internal gelification methods using cobalt and nickel as active metals supported on aluminum, zirconium, lanthanum and cerium oxides. After prepared and calcined at 550 Cº the solids were fully characterized by different techniques such as X-rays diffraction(DRX), energy-dispersive X-ray spectroscopy (EDS), scanning electron microscopy, nitrogen adsorption (B.E.T), temperature-programmed reduction in H2 (TPR-H2) and thermogravimetric analysis. The catalytic tests were performed in a monolithic quartz reactor and submitted to different thermodynamic conditions of steam reforming of ethanol at temperatures varying from 500º C to 800 ºC. The product gas streams from the reactor were analyzed by an on-line gas chromatograph. The cobalt/nickel catalyst supported on a ceria-lanthania mixture (Co 10% / Ni 5% - CeO 2 La 2 O 3 ) showed good catalytic performance in hydrogen selectivity reaching a concentration greater than 65%, when compared to other catalytic systems such as: Co 10% / Ni5% - CeO 2 ; Co 10% / Ni 5% - CeO 2 ZrO 2 ; Co 10% / Ni 5% - ZrO 2 ; Co 10% / Ni 5% - La 2 O 3 ; Co 10% / Ni 5% - CeO 2 La 2 O 3 /K 2% ; Co 10 % / Ni 5% - CeO 2 La 2 O 3 / Na 2% ; Ni 10% / Co 5% - CeO 2 La 2 O 3 ; Co-Al 2 O 3 e Co-Al 2 O 3 CeO 2 . (author)

The Relationship Between Family, Parent, and Child Characteristics and Intimate-Partner Violence (IPV) Among Ukrainian Mothers.

Science.gov (United States)

Burlaka, Viktor; Grogan-Kaylor, Andrew; Savchuk, Olena; Graham-Bermann, Sandra A

2017-07-01

To assess the prevalence of intimate partner violence (IPV) in a sample of Ukrainian mothers of schoolchildren, and to examine the relationship between IPV and family, parent, and child characteristics utilizing multilevel models. Mothers of children aged 9-16 (n = 278, 93.5% Ukrainians) answered the Revised Conflict Tactics Scale (CTS2) assessing IPV. We also examined the relationship between IPV and maternal age, education, employment and marital status, family income, and rural or urban residence. Eighty-one percent of women reported psychological violence and 58% reported physical assault. On average, women reported 66 instances of IPV during the last year. Multilevel modeling revealed that lower maternal education, unemployment, not living with the husband or partner, and urban residency were associated with higher IPV victimization. Younger age and family income were not significantly related to IPV. IPV was a significant social problem in the present sample of Ukrainian mothers of school age children. Future policy and violence prevention programming should focus on supporting academic and employment opportunities for women, particularly for those living in urban areas.

Facile synthesis of polypyrrole functionalized nickel foam with catalytic activity comparable to Pt for the poly-generation of hydrogen and electricity

Science.gov (United States)

Tang, Tiantian; Li, Kan; Shen, Zhemin; Sun, Tonghua; Wang, Yalin; Jia, Jinping

2016-01-01

Polypyrrole functionalized nickel foam is facilely prepared through the potentiostatic electrodeposition. The PPy-functionalized Ni foam functions as a hydrogen-evolution cathode in a rotating disk photocatalytic fuel cell, in which hydrogen energy and electric power are generated by consuming organic wastes. The PPy-functionalized Ni foam cathode exhibits stable catalytic activities after thirteen continuous runs. Compared with net or plate structure, the Ni foam with a unique three-dimensional reticulate structure is conducive to the electrodeposition of PPy. Compared with Pt-group electrode, PPy-coated Ni foam shows a satisfactory catalytic performance for the H2 evolution. The combination of PPy and Ni forms a synergistic effect for the rapid trapping and removal of proton from solution and the catalytic reduction of proton to hydrogen. The PPy-functionalized Ni foam could be applied in photocatalytic and photoelectrochemical generation of H2. In all, we report a low cost, high efficient and earth abundant PPy-functionalized Ni foam with a satisfactory catalytic activities comparable to Pt for the practical application of poly-generation of hydrogen and electricity.

Solution-processed copper-nickel nanowire anodes for organic solar cells

Science.gov (United States)

Stewart, Ian E.; Rathmell, Aaron R.; Yan, Liang; Ye, Shengrong; Flowers, Patrick F.; You, Wei; Wiley, Benjamin J.

2014-05-01

This work describes a process to make anodes for organic solar cells from copper-nickel nanowires with solution-phase processing. Copper nanowire films were coated from solution onto glass and made conductive by dipping them in acetic acid. Acetic acid removes the passivating oxide from the surface of copper nanowires, thereby reducing the contact resistance between nanowires to nearly the same extent as hydrogen annealing. Films of copper nanowires were made as oxidation resistant as silver nanowires under dry and humid conditions by dipping them in an electroless nickel plating solution. Organic solar cells utilizing these completely solution-processed copper-nickel nanowire films exhibited efficiencies of 4.9%.This work describes a process to make anodes for organic solar cells from copper-nickel nanowires with solution-phase processing. Copper nanowire films were coated from solution onto glass and made conductive by dipping them in acetic acid. Acetic acid removes the passivating oxide from the surface of copper nanowires, thereby reducing the contact resistance between nanowires to nearly the same extent as hydrogen annealing. Films of copper nanowires were made as oxidation resistant as silver nanowires under dry and humid conditions by dipping them in an electroless nickel plating solution. Organic solar cells utilizing these completely solution-processed copper-nickel nanowire films exhibited efficiencies of 4.9%. Electronic supplementary information (ESI) available. See DOI: 10.1039/c4nr01024h

Multikilowatt hydrogen-nickel oxide battery system

Science.gov (United States)

Dunlop, J. D.

1985-01-01

The potential of the H2-NiO battery for terrestrial applications was assessed. A multicell design approach that differs significantly from the aerospace individual pressure vessel was used. A number of experimental 100-Ah cells were built to evaluate the new design concepts and components. The experimental cells provided the input needed for a multicell battery design. It is found that new multicell H2-NiO battery has a number of potential advantages for aerospace applications such as the manned space station. The advantages are discussed, and a design concept is presented for a multikilowatt battery in a lightweight pressure vessel.

Nickel-silver composition shows promise as catalyst for hydrogen-oxygen fuel cells

Science.gov (United States)

Magerl, J. A.; Murray, J. N.

1970-01-01

Carburized 3-1 nickel-silver preparation exhibits considerable catalytic activity, although not as high as platinum black. Cost and availability factors warrant further evaluation of nickel-silver materials.

The influence of chemistry concentration on the fracture risk of a reactor pressure vessel subjected to pressurized thermal shocks

Energy Technology Data Exchange (ETDEWEB)

Huang, Pin-Chiun [Institute of Nuclear Engineering and Science, National Tsing-Hua University, Hsinchu 30013, Taiwan, ROC (China); Chou, Hsoung-Wei, E-mail: hwchou@iner.gov.tw [Institute of Nuclear Energy Research, Taoyuan 32546, Taiwan, ROC (China); Ferng, Yuh-Ming [Institute of Nuclear Engineering and Science, National Tsing-Hua University, Hsinchu 30013, Taiwan, ROC (China)

2016-02-15

Highlights: • Probabilistic fracture mechanics method was used to analyze a reactor pressure vessel. • Effects of copper and nickel contents on RPV fracture probability under PTS were investigated and discussed. • Representative PTS transients of Beaver Valley nuclear power plant were utilized. • The range of copper and nickel contents of the RPV materials were suggested. • With different embrittlement levels the dominated PTS category is different. - Abstract: The radiation embrittlement behavior of reactor pressure vessel shell is influenced by the chemistry concentration of metal materials. This paper aims to study the effects of copper and nickel content variations on the fracture risk of pressurized water reactor (PWR) pressure vessel subjected to pressurized thermal shock (PTS) transients. The probabilistic fracture mechanics (PFM) code, FAVOR, which was developed by the Oak Ridge National Laboratory in the United States, is employed to perform the analyses. A Taiwan domestic PWR pressure vessel assumed with varied copper and nickel contents of beltline region welds and plates is investigated in the study. Some PTS transients analyzed from Beaver Valley Unit 1 for establishing the U.S. NRC's new PTS rule are applied as the loading condition. It is found that the content variation of copper and nickel will significantly affect the radiation embrittlement and the fracture probability of PWR pressure vessels. The results can be regarded as the risk incremental factors for comparison with the safety regulation requirements on vessel degradation as well as a reference for the operation of PWR plants in Taiwan.

Voltage and capacity stability of the Hubble telescope nickel-hydrogen battery

Energy Technology Data Exchange (ETDEWEB)

Vaidyanathan, H. [Communications Satellite Corp., Clarksburg, MD (United States). COMSAT Labs.; Wajsgras, H. [NASA Goddard Space Flight Center, Greenbelt, MD (United States); Rao, G.M. [NASA Goddard Space Flight Center, Greenbelt, MD (United States)

1996-01-01

The power system of the Ubble Space Telescope includes two orbital replacement units, each containing three nickel-hydrogen (Ni-H{sub 2}) batteries of 88 Ah capacity. Since launch in April 1990, the batteries have completed 23 000 charge and discharge cycles and continue to meet the power demands of the satellite. The voltage, capacity, and pressure characteristics of all six batteries were analyzed to determine the state of health of the battery and to identify any signs of performance degradation. The battery pressures have changed to varying degrees. The end-of-charge pressure for battery 4 increased by 96 psi, while that for battery 3 decreased by 37 psi. The voltages of the individual cells show a decay rate of 0.69 mV per 1000 cycles, and the capacity of the batteries has apparently decreased, possibly due to the system being operated at a lower stage of charge. Autonomous battery operation involving charge termination at a preselected voltage continues to restore the energy dissipated during each orbit. The accumulated data on voltages and recharge ratios can be used to design new temperature-compensated voltage levels for similar missions that employ Ni-H{sub 2} batteries. (orig.)

Contribution to the study of the electrodeposition of iron-nickel alloys

International Nuclear Information System (INIS)

Valignat, J.

1968-01-01

Using a coulometric technique based upon the anodic intentiostatic dissolution, we studied the potentiostatic, deposition of nickel, iron and nickel iron alloys. We have shown that the minimum of the curve I = f (t) (deposition current versus time) is probably due to the transitory blocking of the surface by hydrogen and that the syn-crystallisation of nickel and iron is responsible for the anomalous co-deposition of these two elements. (author) [fr

ARGAZ: a new device for experimental study of the coupling between hydrogen production and hydrogen transfer through saturated Callovian-Oxfordian argillite

International Nuclear Information System (INIS)

Imbert, C.; Bataillon, C.; Touze, G.; Vigier, P.; Talandier, J.

2010-01-01

Document available in extended abstract form only. A specific experimental device has been designed to produce hydrogen at the metal-argillite interface by electrochemistry. The target is for one hand to reproduce the production of hydrogen occurring when a metal is corroded by the water contained in the porosity of the mud-stone. On the other hand, the transfer of the hydrogen through the mud-stone can be studied. The specific features of the experiment are the following: - Hydrogen is generated inside a cell by electrochemistry, at the interface between the argillite and a metallic surface; no gas injection is required; - Electrochemistry gives the possibility to control the hydrogen production rate; - Hydrogen generation implies water consumption: the water comes from the porosity of the bulk argillite, near the interface; - That one-dimensional experiment has been built around a cylindrical sample of bulk and undamaged argillite coming from the Callovian-Oxfordian formation. Inside the device a cylindrical sample of argillite is placed above a nickel plate. Around the argillite, a ring of compacted bentonite ensures a mechanical confinement. When saturated, the bentonite will apply a swelling pressure close to the total pressure encountered by the sample in the geological formation. The hydrogen is generated at the interface nickel-argillite. The nickel plate is one of the two electrodes required for electrochemistry. At the top face of bentonite, iron electrode is used to close the electrical circuit. The hydrogen produced at the bottom face of the mud-stone is expected to go across the argillite towards the top face. A porous plate connected with a sampling bottle allows the capture of hydrogen. The argillite sample has a diameter of 50 mm, and a height of 50 mm. It is obtained by over-coring a core sample, and by a careful machining leading to a perfect geometry and surface quality. The production rate of hydrogen can be calculated from the current intensity

Hydrogenation of citral into its derivatives using heterogeneous catalyst

Science.gov (United States)

Sudiyarmanto, Hidayati, Luthfiana Nurul; Kristiani, Anis; Aulia, Fauzan

2017-11-01

Citral as known as a monoterpene can be found in plants and citrus fruits. The hydrogenation of citral into its derivatives become interesting area for scientist. This compound and its derivatives can be used for many application in pharmaceuticals and food areas. The development of heterogeneous catalysts become an important aspect in catalytic hydrogenation citral process. Nickel supported catalysts are well known as hydrogenation catalyst. These heterogeneous catalysts were tested their catalytic activity in hydrogenation of citral. The effect of various operation conditions, in term of feed concentration, catalyst loading, temperature, and reaction time were also studied. The liquid products produced were analyzed by using Gas Chromatography-Mass Spectroscopy (GC-MS). The result of catalytic activity tests showed nickel skeletal catalyst exhibits best catalytic activity in hydrogenation of citral. The optimum of operation condition was achieved in citral concentration 0.1 M with nickel skeletal catalyst loading of 10% (w/w) at 80 °C and 20 bar for 2 hours produced the highest conversion as of 64.20% and the dominant product resulted was citronellal as of 56.48%.

IPv6 Monitoring in Nederland: De derde meting : TNO-White paper

NARCIS (Netherlands)

Boen-Leo, M.S.A.; Hartog, T.; Holtzer, A.C.G.; Schotanus, H.A.; Smets, R.C.J.; Tijmes, M.R.

2011-01-01

Dit whitepaper beschrijft de derde meting in het kader van IPv6 monitoring in Nederland. Eerder zijn de Nulmeting2 en Tweede Meting3 gepubliceerd. In de tweede helft van 2011 zal nog een vierde meting gepubliceerd worden. Uit de vorige metingen is gebleken dat IPv6 bewustzijn toeneemt, maar dat het

Duplicate Address Detection Table in IPv6 Mobile Networks

Science.gov (United States)

Alisherov, Farkhod; Kim, Taihoon

In IP networks, each computer or communication equipment needs an IP address. To supply enough IP addresses, the new Internet protocol IPv6 is used in next generatoion mobile communication. Although IPv6 improves the existing IPv4 Internet protocol, Duplicate Address Detection (DAD) mechanism may consume resources and suffer from long delay. DAD is used to ensure whether the IP address is unique or not. When a mobile node performs an inter-domain handoff, it will first generate a new IP and perform a DAD procedure. The DAD procedure not only wastes time but also increases the signaling load on Internet. In this paper, the author proposes a new DAD mechanism to speed up the DAD procedure. A DAD table is created in access or mobility routers in IP networks and record all IP addresses of the area. When a new IP address needs to perform DAD, it can just search in the DAD table to confirm the uniqueness of the address.

Peer Influence on IPV by Young Adult Males: Investigating the Case for a Social Norms Approach.

Science.gov (United States)

McKool, Marissa; Stephenson, Rob; Winskell, Kate; Teten Tharp, Andra; Parrott, Dominic

2017-08-01

Nearly 32% of women report experiencing physical violence from an intimate partner and more than 8% report being raped by a significant other in their lifetime. Young people's perceptions that their peers perpetrate relationship violence have been shown to increase the odds of self-reported perpetration. Yet, limited research has been conducted on this relationship as individuals begin to age out of adolescence. The present study sought to examine the link between the perception of peer perpetration of intimate partner violence (IPV) and self-reported IPV perpetration among a sample of predominately young adult (21-35 years) males. This study also explored the discordance between the perception of peer IPV behavior and self-reported perpetration. Data from 101 male peer dyads ( n = 202) were taken from a study on the effects of alcohol and bystander intervention in Atlanta, Georgia. Thirty-six percent ( n = 73) of men reported perpetrating physical IPV and 67% ( n = 135) reported perpetrating sexual IPV in the past 12 months. Nearly 35% ( n = 55) of the sample reported that none of their peers had perpetrated physical IPV, which contradicted their friend's self-report of physical IPV perpetration. Similarly, 68% ( n = 115) of the men perceived none of their peers to have perpetrated sexual IPV, which contradicted their friend's self-report of sexual IPV perpetration. Discordance variables were significantly associated with self-reported perpetration for both physical (χ 2 = 152.7, p peer IPV perpetration among young adult males. Findings suggest a traditional social norms approach to IPV prevention, which seeks to persuade individuals that negative behaviors are less common than perceived, may not be the best approach given a significant number of men believed their friends were nonviolent when they had perpetrated violence.

Hydrogenations of alloys and intermetallic compounds of magnesium

International Nuclear Information System (INIS)

Gavra, Z.

1981-08-01

A kinetic and thermodynamic study of the hydrogenation of alloys and intermetallic compounds of magnesium is presented. It was established that the addition of elements of the IIIA group (Al, Ga, In) to magnesium catalyses its hydrogenation. This is explained by the mechanism of diffusion of magnesium cation vacancies. The hydride Mg 2 NiH 4 was characterized by thermal analysis, x-ray diffraction and NMR measurements. The possibility of forming pseudo-binary compounds of Mg 2 Ni by the substitution of nickel or magnesium was examined. The hydrogenation of the inter-metallic compounds of the Mg-Al system was investigated. It was found that the addition of indium and nickel affected the hydrogenation kinetics. A preliminary study of the hydrogenation of various binary and ternary alloys of magnesium was carried out. (Author)

Desempeño de la calidad del servicio (QoS sobre IPv6

Directory of Open Access Journals (Sweden)

Octavio José Salcedo Parra

2011-06-01

Full Text Available New applications such as VoIP, e-commerce and video conferencing are sensitive to network performance, making the network capacity to provide quality of service is increasingly important. IPv6 was developed to solve some of the problems of IPv4, such as QoS, security and IP address exhaustion. Current IP networks provide better trafficdelivery effort, therefore, offer no guarantee of quality service. However, there are services, including voice, with stringent requirements for delay and delay variation (jitter, which makes it necessary to add functionality to IP networks based on this protocol are capable of supporting such services. For its part, IPv6 uses 2 fields that can be used to implement QoS, which are: Flow Label and Traffic Class. This article describes the mechanisms and architectures that are used to provide QoS on a network. Later, you specify the features that use both IPv4 and IPv6 to implement QoS. In the last sections present the results of the comparison of 2 scenarios, which are evaluated.

A new concept for high-cycle-life LEO: Rechargeable MnO2-hydrogen

Science.gov (United States)

Appleby, A. J.; Dhar, H. P.; Kim, Y. J.; Murphy, O. J.

1989-01-01

The nickel-hydrogen secondary battery system, developed in the early 1970s, has become the system of choice for geostationary earth orbit (GEO) applications. However, for low earth orbit (LEO) satellites with long expected lifetimes the nickel positive limits performance. This requires derating of the cell to achieve very long cycle life. A new system, rechargeable MnO2-Hydrogen, which does not require derating, is described here. For LEO applications, it promises to have longer cycle life, high rate capability, a higher effective energy density, and much lower self-discharge behavior than those of the nickel-hydrogen system.

Reaction of Hydrogen Sulfide with Oxygen in the Presence ofSulfite

Energy Technology Data Exchange (ETDEWEB)

Weres, Oleh; Tsao, Leon

1983-01-01

Commonly, abatement of hydrogen sulfide emissions from a geothermal powerplant requires that hydrogen sulfide dissolved in the cooling water be eliminated by chemical reaction. Oxidation by atmospheric oxygen is the preferred reaction, but requires a suitable catalyst. Nickel is the most potent and thereby cheapest catalyst for this purpose. One Mg/L nickel in the cooling water would allow 99% removal of hydrogen sulfide to be attained. A major drawback of catalytic air oxidation is that colloidal sulfur is a major reaction product; this causes rapid sludge accumulation and deposition of sulfur scale. The authors studied the kinetics and product distribution of the reaction of hydrogen sulfide with oxygen, catalyzed by nickel. Adding sodium sulfite to the solution completely suppresses formation of colloidal sulfur by converting it to thiosulfate. The oxidation reaction is an autocatalytic, free radical chain reaction. A rate expression for this reaction and a detailed reaction mechanism were developed. Nickel catalyzes the chain initiation step, and polysulfidoradical ions propagate the chains. Several complexes of iron and cobalt were also studied. Iron citrate and iron N-hydroxyEDT are the most effective iron based catalysts. Uncomplexed cobalt is as effective as nickel, but forms a precipitate of cobalt oxysulfide and is too expensive for practical use.

Reaction of hydrogen sulfide with oxygen in the presence of sulfite

Energy Technology Data Exchange (ETDEWEB)

Weres, O.; Tsao, L.

1983-01-14

Commonly, abatement of hydrogen sulfide emission from a geothermal powerplant requires that hydrogen sulfide dissolved in the cooling water be eliminated by chemical reaction. Oxidation by atmospheric oxygen is the preferred reaction, but requires a suitable catalyst. Nickel is the most potent and thereby cheapest catalyst for this purpose. One mg/L nickel in the cooling water would allow 99% removal of hydrogen sulfide to be attained. A major drawback of catalytic air oxidation is that colloidal sulfur is a major reaction product; this causes rapid sludge accumulation and deposition of sulfur scale. We studied the kinetics and product distribution of the reaction of hydrogen sulfide with oxygen, catalyzed by nickel. Adding sodium sulfite to the solution completely suppresses formation of colloidal sulfur by converting it to thiosulfate. The oxidation reaction is an autocatalytic, free radical chain reaction. A rate expression for this reaction and a detailed reaction mechanism were developed. Nickel catalyzes the chain initiation step, and polysulfidoradical ions propagate the chains. Several complexes of iron and cobalt were also studied. Iron citrate and iron N-hydroxyEDTA are the most effective iron based catalysts. Uncomplexed cobalt is as effective as nickel, but forms a precipitate of cobalt oxysulfide and is too expensive for practical use. 33 figures, 9 tables.

IPv6 testing and deployment at Prague Tier 2

Science.gov (United States)

Kouba, Tomáŝ; Chudoba, Jiří; Eliáŝ, Marek; Fiala, Lukáŝ

2012-12-01

Computing Center of the Institute of Physics in Prague provides computing and storage resources for various HEP experiments (D0, Atlas, Alice, Auger) and currently operates more than 300 worker nodes with more than 2500 cores and provides more than 2PB of disk space. Our site is limited to one C-sized block of IPv4 addresses, and hence we had to move most of our worker nodes behind the NAT. However this solution demands more difficult routing setup. We see the IPv6 deployment as a solution that provides less routing, more switching and therefore promises higher network throughput. The administrators of the Computing Center strive to configure and install all provided services automatically. For installation tasks we use PXE and kickstart, for network configuration we use DHCP and for software configuration we use CFEngine. Many hardware boxes are configured via specific web pages or telnet/ssh protocol provided by the box itself. All our services are monitored with several tools e.g. Nagios, Munin, Ganglia. We rely heavily on the SNMP protocol for hardware health monitoring. All these installation, configuration and monitoring tools must be tested before we can switch completely to IPv6 network stack. In this contribution we present the tests we have made, limitations we have faced and configuration decisions that we have made during IPv6 testing. We also present testbed built on virtual machines that was used for all the testing and evaluation.

IPv6 testing and deployment at Prague Tier 2

International Nuclear Information System (INIS)

Kouba, Tomáŝ; Chudoba, Jiří; Eliáŝ, Marek; Fiala, Lukáŝ

2012-01-01

Computing Center of the Institute of Physics in Prague provides computing and storage resources for various HEP experiments (D0, Atlas, Alice, Auger) and currently operates more than 300 worker nodes with more than 2500 cores and provides more than 2PB of disk space. Our site is limited to one C-sized block of IPv4 addresses, and hence we had to move most of our worker nodes behind the NAT. However this solution demands more difficult routing setup. We see the IPv6 deployment as a solution that provides less routing, more switching and therefore promises higher network throughput. The administrators of the Computing Center strive to configure and install all provided services automatically. For installation tasks we use PXE and kickstart, for network configuration we use DHCP and for software configuration we use CFEngine. Many hardware boxes are configured via specific web pages or telnet/ssh protocol provided by the box itself. All our services are monitored with several tools e.g. Nagios, Munin, Ganglia. We rely heavily on the SNMP protocol for hardware health monitoring. All these installation, configuration and monitoring tools must be tested before we can switch completely to IPv6 network stack. In this contribution we present the tests we have made, limitations we have faced and configuration decisions that we have made during IPv6 testing. We also present testbed built on virtual machines that was used for all the testing and evaluation.

A theoretical study on the mechanism of hydrogen evolution on non-precious partially oxidized nickel-based heterostructures for fuel cells.

Science.gov (United States)

Pan, Xinju; Zhou, Gang

2018-03-28

It is desirable, yet challenging, to utilize non-precious metals instead of noble-metals as efficient catalysts in the renewable energy manufacturing industry. Using first principles calculations, we study the structural characteristics of partially oxidized nickel-based nanoheterostructures (NiO/Ni NHSs), and the interfacial effects on hydrogen evolution. The origin of the enhanced hydrogen evolution performance is discussed at the microscopic level. This study identifies two types of active sites of the exposed Ni surface available for the hydrogen evolution reaction (HER). One is the hcp-hollow sites near the perimeter boundary that exhibit a more excellent HER performance than platinum (Pt), and the other the second nearest neighbor fcc-hollow sites away from the boundary that exhibit a similar performance to Pt. The interfacial effects result from the competitive charge transfer between NiO and Ni surfaces in NHSs, and enhance the reactivity of NiO/Ni NHSs by shifting the d-states of surface atoms down in energy. The illumination of the mechanism would be helpful for the design of more efficient and cheap transition metal-based catalysts.

Thermoelectric and Hall-effect studies in hydrogenerated nickel foils

International Nuclear Information System (INIS)

Rani, R.; Nigam, A.N.

1978-01-01

Thermo e.m.f. and Hall constant of hydrogenerated nickel foils have been measured. Termo e.m.f. shows a sign reversal which is not due to the change in sign of the charge carriers, as indicated by the Hall-effect measurements. To account for the sign reversal of thermo e.m.f., it is found necessary to take into account the surface states of chemisorbed hydrogen on nickel

Preparation and characterization of nickel catalysts supported on cerium for obtaining hydrogen from steam reforming of ethanol

International Nuclear Information System (INIS)

Urbaninho, A.B.; Bergamaschi, V.S.; Ferreira, J.C.

2016-01-01

The Ni/Ce catalysts for were prepared by co- precipitation method with a view to their use in steam reforming of ethanol to produce a hydrogen-rich gas mixture. The catalysts were characterized by scanning electron microscopy; x-ray dispersive Spectroscopy and surface area BET method. This paper proposes to prepare, characterize and test nickel catalyst supported on cerium in order to obtain a material with higher activity and selectivity of the catalyst using the steam reforming reaction of ethanol, by varying the reaction temperature, molar ratio water/ethanol and uptime. The catalytic tests were monitored by chemical analysis of syngas from steam reforming of ethanol using an analysis online by gas Chromatograph in the reactor. (author)

System for Malicious Node Detection in IPv6-Based Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Kresimir Grgic

2016-01-01

Full Text Available The trend of implementing the IPv6 into wireless sensor networks (WSNs has recently occurred as a consequence of a tendency of their integration with other types of IP-based networks. The paper deals with the security aspects of these IPv6-based WSNs. A brief analysis of security threats and attacks which are present in the IPv6-based WSN is given. The solution to an adaptive distributed system for malicious node detection in the IPv6-based WSN is proposed. The proposed intrusion detection system is based on distributed algorithms and a collective decision-making process. It introduces an innovative concept of probability estimation for malicious behaviour of sensor nodes. The proposed system is implemented and tested through several different scenarios in three different network topologies. Finally, the performed analysis showed that the proposed system is energy efficient and has a good capability to detect malicious nodes.

Thermogravimetric study of the reduction of oxides of nickel and chromium

Science.gov (United States)

Herbell, T. P.

1973-01-01

The effectiveness of hydrogen, carbon and hydrogen-carbon in reducing NiO, Cr2O3, mixed NiO-Cr2O3 and oxidized Ni-20Cr was evaluated by thermogravimetry. NiO was effectively reduced by all three atmospheres, Cr2O3 only by hydrogen-carbon, NiO-Cr2O3 by hydrogen and hydrogen-carbon and oxidized Ni-20Cr by hydrogen, hydrogen-carbon and partially by carbon alone. The results indicate that nickel and carbon promote the reduction of Cr2O3.

Pressure vessels fabricated with high-strength wire and electroformed nickel

Science.gov (United States)