Technical aspects of biodiesel production from vegetable oils

Directory of Open Access Journals (Sweden)

Krishnakumar Janahiraman

2008-01-01

Full Text Available Biodiesel, a promising substitute as an alternative fuel has gained significant attention due to the finite nature of fossil energy sources and does not produce sulfur oxides and minimize the soot particulate in comparison with the existing one from petroleum diesel. The utilization of liquid fuels such as biodiesel produced from vegetable oil by transesterification process represents one of the most promising options for the use of conventional fossil fuels. In the first step of this experimental research, edible rice bran oil used as test material and converted into methyl ester and non-edible jatropha vegetable oil is converted into jatropha oil methyl ester, which are known as biodiesel and they are prepared in the presence of homogeneous acid catalyst and optimized their operating parameters like reaction temperature, quantity of alcohol and the catalyst requirement, stirring rate and time of esterification. In the second step, the physical properties such as density, flash point, kinematic viscosity, cloud point, and pour point were found out for the above vegetable oils and their methyl esters. The same characteristics study was also carried out for the diesel fuel for obtaining the baseline data for analysis. The values obtained from the rice bran oil methyl ester and jatropha oil methyl ester are closely matched with the values of conventional diesel and it can be used in the existing diesel engine without any hardware modification. In the third step the storage characteristics of biodiesel are also studied. .

Breads Fortified with Freeze-Dried Vegetables: Quality and Nutritional Attributes. Part II: Breads Not Containing Oil as an Ingredient

Directory of Open Access Journals (Sweden)

Viren Ranawana

2016-09-01

Full Text Available The present article describes the second part of a study investigating the effect of adding vegetables on the nutritional, physico-chemical, and oxidative properties of wheat bread, and specifically focuses on bread that does not contain oil as an added ingredient. Wheat flour breads fortified with freeze-dried carrot, tomato, beetroot or broccoli were developed and assessed for their nutritional composition, antioxidant potential, oxidative stability, and storage properties. Using a simulated in vitro model, the study also examined the impact of vegetable addition on the oxidative stability of macronutrients during gastro-intestinal digestion. Adding vegetables improved the nutritional and functional attributes of the oil-free breads. However, they demonstrated a lower antioxidant potential compared to their oil-containing counterparts. Similarly, the textural and storage properties of the oil-free vegetable breads were poorer compared to the oil-containing breads. As expected, in the absence of oil the oil-free breads were associated with lower lipid oxidation both in their fresh form and during gastro-intestinal digestion. Adding vegetables reduced protein oxidation in the fresh oil-free breads but had no effect during gastro-intestinal digestion. The impact of vegetables on macronutrient oxidation in the oil-free breads during digestion appears to be vegetable-specific with broccoli exacerbating it and the others having no effect. Of the evaluated vegetables, beetroot showed the most promising nutritional and physico-chemical benefits when incorporated into bread that does not contain added oil.

CONSIDERATIONS ABOUT THE USE OF LOVAGE LEAVES TO IMPROVE THE QUALITY OF EDIBLE VEGETABLE OILS AND OIL BLENDS

OpenAIRE

GEIDA SEVDAGUL SULIMAN; SEMAGHIUL BIRGHILA; ANCA DUMBRAVA

2018-01-01

We studied four edible vegetable oils and nine oil blends based on refined sunflower oil, in order to improve the quality characteristics of sunflower oil. The oils used for blends were linseed oil, grapeseed oil, and coconut oil. The physico-chemical properties demonstrated the superior features for oil blends, like lower acidity (measured by acid value) and higher stability to autoxidation (measured by peroxide value and refractive index). The best combination for sunflower oil was with coc...

[Efficiency evaluation of capsaicinoids to discriminate bio-waste oils from edible vegetable oils].

Science.gov (United States)

Mao, Lisha; Liu, Honghe; Kang, Li; Jiang, Jie; Liao, Shicheng; Liu, Guihua; Deng, Pingjian

2014-07-01

To evaluate the efficiency of capsaicinoids to discriminate bio-waste oil from edible vegetable oil. 14 raw vegetable oils, 24 fried waste oils, 34 kitchen-waste oils, 32 edible non-peanut vegetable oil, 32 edible peanuts oil, 16 edible oil add flavorand and 11 refined bio-waste oils were prepared and examined for capsaicinoids including capsaicin, dihydrocapsaicin and nonylic acid vanillylamide. The detection results of the above samples were statistically tested based on sample category to assessment identify the effectiveness of the bio-waste oils with capsaicinoids. As a indicator, capsaincin was possessed of high detection sensitivity and has the highest efficiency to discern kitchen-waste oils and refined bio-waste oils samples from edible non-peanut vegetable oil correctly. The accuracy rate of identification were 100% and 90.1% respectively. There is the background in peanut oil. CONCLUSION Capsaicin added in cooking process can be retained in the refining process and hardly be removed in the refining process. In the case of fully eliminating the background interference, capsaicinoids can effectively identify bio-waste oils and edible vegetable oil in combination.

Disinfection of vegetable seed by treatment with essential oils, organic acids and plant extract

NARCIS (Netherlands)

Wolf, van der J.M.; Birnbaum, Y.E.; Zouwen, van der P.S.; Groot, S.P.C.

2008-01-01

Various essential oils, organic acids, Biosept, (grapefruit extract), Tillecur and extracts of stinging nettle and golden rod were tested for their antimicrobial properties in order to disinfect vegetable seed. In in vitro assays, thyme oil, oregano oil, cinnamon oil, clove oil and Biosept had the

CONSIDERATIONS ABOUT THE USE OF LOVAGE LEAVES TO IMPROVE THE QUALITY OF EDIBLE VEGETABLE OILS AND OIL BLENDS

Directory of Open Access Journals (Sweden)

GEIDA SEVDAGUL SULIMAN

2018-03-01

Full Text Available We studied four edible vegetable oils and nine oil blends based on refined sunflower oil, in order to improve the quality characteristics of sunflower oil. The oils used for blends were linseed oil, grapeseed oil, and coconut oil. The physico-chemical properties demonstrated the superior features for oil blends, like lower acidity (measured by acid value and higher stability to autoxidation (measured by peroxide value and refractive index. The best combination for sunflower oil was with coconut oil (lower acidity, higher stability to autoxidation. For a supplementary improvement of properties, especially for the preservation of oils and oil blends, we tested the lovage (Levisticum officinale extract as additive. The obtained additivated mixtures demonstrated better quality characteristics, which recommend them for the human consumption.

Transesterification of Vegetable Oils with Ethanol and Characterization of the Key Fuel Properties of Ethyl Esters

Directory of Open Access Journals (Sweden)

Stamoulis Stournas

2009-06-01

Full Text Available The transesterification reactions of four different vegetable oils (sunflower, rapeseed, olive oil and used frying oil with ethanol, using sodium hydroxide as catalyst, were studied. The ester preparation involved a two-step transesterification reaction, followed by purification. The effects of the mass ratio of catalyst to oil (0.25 – 1.5%, the molar ratio of ethanol to oil (6:1 – 12:1, and the reaction temperature (35 – 90 °C were studied for the conversion of sunflower oil to optimize the reaction conditions in both stages. The rest of the vegetable oils were converted to ethyl esters under optimum reaction parameters. The optimal conditions for first stage transesterification were an ethanol/oil molar ratio of 12:1, NaOH amount (1% wt/wt, and 80 °C temperature, whereas the maximum yield of ethyl esters reached 81.4% wt/wt. In the second stage, the yield of ethyl esters was improved by 16% in relation with the one-stage transesterification, which was obtained under the following optimal conditions: catalyst concentration 0.75% and ethanol/oil molar ratio 6:1. The fuel properties of the esters were measured according to EN test methods. Based on the experimental results one can see that the ethyl esters do not differ significantly from methyl esters. Moreover, the results showed that the values of density, viscosity, and higher heating value of ethyl esters were similar to those of automotive and heavy duty engine diesel fuel. However, the CFPP values were higher, which may contribute to potential difficulties in cold starts. On the other hand, the flash points, which were higher than those of diesel fuel constituted a safety guarantee from the point of view of handling and storage.

Vegetable oil based liquid nanocomposite dielectric

Directory of Open Access Journals (Sweden)

Leon Chetty

2013-01-01

Full Text Available Physically smaller dielectric materials would improve the optimisation of space for power systems. Development of nanotechnology provides an effective way to improve the performances of insulating oils used in power system applications. In this research study, we focused on the development of nanomodified vegetable oils to be used in power transformers. Higher conduction currents were observed in virgin linseed oil than in virgin castor oil. However, for both virgin linseed and virgin castor oil, the DC conduction current increased approximately linearly with the applied DC voltage. In nanomodified linseed oil, the characteristic curve showed two distinct regions: a linear region (at lower applied voltage and a saturation region (at slightly higher voltage. Conversely, in nanomodified castor oil, the characteristic curve showed three distinct regions: a linear region (at lower applied voltage, a saturation region (at intermediate applied voltage and an exponential growth region (at higher applied voltage. The nanomodified linseed oil exhibited a better dielectric performance than the nanomodified castor oil. Overall, the addition of nanodielectrics to vegetable oils decreased the dielectric performance of the vegetable oils. The results of this study contribute to the understanding of the pre-breakdown phenomenon in liquid nanocomposite dielectrics.

Phenolation of vegetable oils

Directory of Open Access Journals (Sweden)

ZORAN S. PETROVIĆ

2011-04-01

Full Text Available Novel bio-based compounds containing phenols suitable for the syn­thesis of polyurethanes were prepared. The direct alkylation of phenols with different vegetable oils in the presence of superacids (HBF4, triflic acid as ca­talysts was studied. The reaction kinetics was followed by monitoring the de­crease of the double bond content (iodine value with time. In order to under­stand the mechanism of the reaction, phenol was alkylated with model com­pounds. The model compounds containing one internal double bond were 9-oc­tadecene and methyl oleate and those with three double bonds were triolein and high oleic safflower oil (82 % oleic acid. It was shown that the best structures for phenol alkylation are fatty acids with only one double bond (oleic acid. Fatty acids with two double bonds (linoleic acid and three double bonds (lino­lenic acid lead to polymerized oils by a Diels–Alder reaction, and to a lesser extent to phenol alkylated products. The reaction product of direct alkylation of phenol with vegetable oils is a complex mixture of phenol alkylated with poly­merized oil (30–60 %, phenyl esters formed by transesterification of phenol with triglyceride ester bonds (<10 % and unreacted oil (30 %. The phenolated vegetable oils are new aromatic–aliphatic bio-based raw materials suitable for the preparation of polyols (by propoxylation, ethoxylation, Mannich reactions for the preparation of polyurethanes, as intermediates for phenolic resins or as bio-based antioxidants.

New options for conversion of vegetable oils to alternative fuels

Energy Technology Data Exchange (ETDEWEB)

Demirbas, A.; Kara, H. [Selcuk University, Konya (Turkey). Department of Chemical Engineering

2006-05-15

Biodiesel from transesterification of vegetable oils is an excellent alternative fuel. There is, however, a need to develop a direct process for conversion of vegetable oils into gasoline-competitive biodiesel and other petroleum products. Methyl esters of vegetable oils have several outstanding advantages among other new-renewable and clean engine fuel alternatives. The purpose of the transesterification process is to lower the viscosity of vegetable oil. Compared to No. 2 diesel fuel, all of the vegetable oils are much more viscous, whereas methyl esters of vegetable oils are slightly more viscous. The methyl esters are more volatile than those of the vegetable oils. Conversion of vegetable oils to useful fuels involves the pyrolysis and catalytic cracking of the oils into lower molecular products. Pyrolysis produces more biogasoline than biodiesel fuel. Soap pyrolysis products of vegetable oils can be used as alternative diesel engine fuel. The soaps obtained from the vegetable oils can be pyrolyzed into hydrocarbon-rich products. Zinc chloride catalyst contributed greatly to high amounts of hydrocarbons in the liquid product. The yield of ZnCl2 catalytic conversion of the soybean oil reached the maximum 79.9% at 660 K. (author)

Production and comparison of fuel properties, engine performance, and emission characteristics of biodiesel from various non-edible vegetable oils: A review

International Nuclear Information System (INIS)

Ashraful, A.M.; Masjuki, H.H.; Kalam, M.A.; Rizwanul Fattah, I.M.; Imtenan, S.; Shahir, S.A.; Mobarak, H.M.

2014-01-01

Highlights: • Overview of current energy situation. • Overview of biology, distribution and chemistry of various non-edible oil resources. • Comparison of fuel properties of various biodiesels produced from various non-edible oils. • Comparison of engine performance and emission characteristics of reviewed biodiesels. - Abstract: Energy demand is increasing dramatically because of the fast industrial development, rising population, expanding urbanization, and economic growth in the world. To fulfill this energy demand, a large amount of fuel is widely used from different fossil resources. Burning of fossil fuels has caused serious detrimental environmental consequences. The application of biodiesel has shown a positive impact in resolving these issues. Edible vegetable oils are one of the potential feedstocks for biodiesel production. However, as the use of edible oils will jeopardize food supplies and biodiversity, non-edible vegetable oils, also known as second-generation feedstocks, are considered potential substitutes of edible food crops for biodiesel production. This paper introduces some species of non-edible vegetables whose oils are potential sources of biodiesel. These species are Pongamia pinnata (karanja), Calophyllum inophyllum (Polanga), Maduca indica (mahua), Hevea brasiliensis (rubber seed), Cotton seed, Simmondsia chinesnsis (Jojoba), Nicotianna tabacum (tobacco), Azadirachta indica (Neem), Linum usitatissimum (Linseed) and Jatropha curcas (Jatropha). Various aspects of non-edible feedstocks, such as biology, distribution, and chemistry, the biodiesel’s physicochemical properties, and its effect on engine performance and emission, are reviewed based on published articles. From the review, fuel properties are found to considerably vary depending on feedstocks. Analysis of the performance results revealed that most of the biodiesel generally give higher brake thermal efficiency and lower brake-specific fuel consumption. Emission results

Physico-chemical properties of blends of palm olein with other vegetable oils

Directory of Open Access Journals (Sweden)

Mobin Siddique, Bazlul

2010-12-01

Full Text Available Palm oil (olein was blended with other edible oils for the enhancement of its market acceptability in terms of melting point depression and shelf life. The physico-chemical properties like viscosity, density, melting behavior, peroxide value (PV, saponification value (SV and iodine value (IV of four different binary blends with four vegetable oils were evaluated. Palm olein was found to be more stable against rancidity than the other oils. For the stability against oxidation and melting point depression the palm olein-canola (PO/CO blend was found to be better than the others. The Differential Scanning Calorimeter (DSC thermogram of the melting behavior of the blends traces some new polymorphs of the triglyceride. This study will help the oil producing industry to find out the most economically viable oil blends for cooking purposes, with maximum nutrition as well as desirable physico-chemical properties.

Aceite de palma (oleína fue mezclada con otros aceites comestibles para aumentar su aceptabilidad en el mercado en términos de descenso del punto de fusión y mejora de su almacenamiento. Las propiedades físico-químicas tales como viscosidad, densidad, comportamiento en la fusión, valor de peróxidos (PV, valor de saponificación (SV e índice de yodo (IV de cuatro diferentes mezclas binarias con cuatro aceites vegetales fueron evaluadas. La oleína de palma fue más estable frente a la rancidez que otros aceites. En la estabilidad frente la oxidación y el descenso del punto de fusión, la mezcla de oleína de palma/canola (PO/CO fue mejor que las otras. Los termogramas del calorímetro diferencial de barrido (DSC referidos al comportamiento de fusión de las mezclas indican algunos nuevos polimorfismos de los triglicéridos. Este estudio podría ayudar a las empresas que elaboran aceites a encontrar los aceites económicamente más viables para cocinar, con buenas propiedades nutricionales, así como con unas propiedades f

Diesel fuel from vegetable oil via transesterification and soap pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Demirbas, A.

2002-09-15

Transesterifications of 6 vegetable oil samples in supercritical methanol (SC MeOH) were studied without using any catalyst. Methyl esters of vegetable oils have several outstanding advantages among other new-renewable and clean engine fuel alternatives. The variables affecting the methyl ester yielded during the transesterification reaction, such as the molar ratio of alcohol to vegetable oil and reaction temperature, were investigated. Compared to No. 2 diesel fuel, all of the vegetable oils are much more viscous, while methyl esters of vegetable oils are the slightly more viscous. The methyl esters are more volatile than those of the vegetable oils. The soaps obtained from the vegetable oils can be pyrolyzed into hydrocarbon-rich products. (author)

The influence of animal fat replacement with vegetable oils on sensorial perception of meat emulsified products

Directory of Open Access Journals (Sweden)

Cristian TUDOSE

2014-12-01

Full Text Available For the purpose of the present study, in an emulsified meat product the pork backfat was replaced with a vegetable oil pre-emulsion and its effect on quality attributes were investigated. In order to do so, a classic and a new meat products were manufactured. Extra virgin olive oil and palm oil pre-emulsion were added instead of animal fat in the new product. Texture and physiochemical properties were analyzed by instrumental measurements. It was observed that during storage moisture and pH decreased. Using vegetable oils determined substantial increase of TBA values. Texture was influenced mainly by storage time for both products, while replacement of pork backfat with vegetable oil pre-emulsion had no influence on sample firmness. The sensory properties of meat products were evaluated by a group of trained panelists using an analitycal sensory evaluation technique. Overall the new product presented good acceptability which recommends it like a new healthier meat product.

Effect of x-rays on edible vegetable oils

International Nuclear Information System (INIS)

Agba, E.H.; Chile, S.T.; Sombo, T.

2009-01-01

X-irradiated and non-irradiated vegetable oil sample were investigated by assessing the effect of the radiation on peroxide and fatty acid values on Turkey oil, Groundnut oil and Soya bean oil samples. The result of the investigation showed a rise in peroxide value by 99% for Turkey oil, 61% for Groundnut oil and 52% for Soya bean oil, while the acid value increased by as much as 58% for Turkey oil, 21% for Groundnut oil and 50% for Soya bean oil. These results show that X-irradiation has an adverse effect on the quality of edible vegetable oils

Encapsulation of vegetable oils as source of omega-3 fatty acids for enriched functional foods.

Science.gov (United States)

Ruiz Ruiz, Jorge Carlos; Ortiz Vazquez, Elizabeth De La Luz; Segura Campos, Maira Rubi

2017-05-03

Polyunsaturated omega-3 fatty acids (PUFAs), a functional component present in vegetable oils, are generally recognized as being beneficial to health. Omega-3 PUFAs are rich in double bonds and unsaturated in nature; this attribute makes them highly susceptible to lipid oxidation and unfit for incorporation into long shelf life foods. The microencapsulation of oils in a polymeric matrix (mainly polysaccharides) offers the possibility of controlled release of the lipophilic functional ingredient and can be useful for the supplementation of foods with PUFAs. The present paper provides a literature review of different vegetable sources of omega-3 fatty acids, the functional effects of omega-3 fatty acids, different microencapsulation methods that can possibly be used for the encapsulation of oils, the properties of vegetable oil microcapsules, the effect of encapsulation on oxidation stability and fatty acid composition of vegetable oils, and the incorporation of long-chain omega-3 polyunsaturated fatty acids in foods.

Analysis of filtration properties of locally sourced base oil for the ...

African Journals Online (AJOL)

This study examines the use of locally sourced oil like, groundnut oil, melon oil, vegetable oil, soya oil and palm oil as substitute for diesel oil in formulating oil base drilling fluids relative to filtration properties. The filtrate volumes of each of the oils were obtained for filtration control analysis. With increasing potash and ...

Natural (Mineral, Vegetable, Coconut, Essential) Oils and Contact Dermatitis.

Science.gov (United States)

Verallo-Rowell, Vermén M; Katalbas, Stephanie S; Pangasinan, Julia P

2016-07-01

Natural oils include mineral oil with emollient, occlusive, and humectant properties and the plant-derived essential, coconut, and other vegetable oils, composed of triglycerides that microbiota lipases hydrolyze into glycerin, a potent humectant, and fatty acids (FAs) with varying physico-chemical properties. Unsaturated FAs have high linoleic acid used for synthesis of ceramide-I linoleate, a barrier lipid, but more pro-inflammatory omega-6:-3 ratios above 10:1, and their double bonds form less occlusive palisades. VCO FAs have a low linoleic acid content but shorter and saturated FAs that form a more compact palisade, more anti-inflammatory omega-6:-3 ratio of 2:1, close to 7:1 of olive oil, which disrupts the skin barrier, otherwise useful as a penetration enhancer. Updates on the stratum corneum illustrate how this review on the contrasting actions of NOs provide information on which to avoid and which to select for barrier repair and to lower inflammation in contact dermatitis genesis.

Researches on thermal and rheological properties of cream- and vegetable spread

Directory of Open Access Journals (Sweden)

A. N. Ostrikov

2016-01-01

Full Text Available Researches of thermal and rheological properties of cream- and vegetable spread are necessary for the scientific substantiation of their obtaining process, namely mixing and crystallization processes. As the object of research, we chose a cream- and vegetable spread, with the following composition: peanut butter 10%; wheat germ oil 10%; linseed oil 20%; butter 59.8%; emulsifier 0.2%. With the data obtained in the course of research of the rheological properties of cream- and vegetable spread, one can subsequently generate recommendations for optimization of technological modes of production. In particular, one can solve problems of intensification of hydro-mechanical and thermal processes by carrying them out at such a temperature and speed when the maximum preservation of the produced product structure will be achieved. Determination of thermal characteristics was carried out in the apparatus for the study of thermal and rheological properties of viscoelastic liquids Coesfeld RT-1394H. Rheological researches of cream- and vegetable spread were carried out on a series of viscometers SV-10 and PB-8m. The graphs of spread dynamic viscosity dependence on the temperature, and the dependence of the effective viscosity of the spread and vegetable oils on the shear rate were built according to experimental data. The data obtained is rational to choose the equipment for processing and production of cream- and vegetable spread, to simulate processes taking place in the production process, to solve problems of intensification of thermal and hydro-mechanical processes reasonably, by conducting the production process at temperatures that do not cause the destruction of the product structure.

Straight Vegetable Oil as a Diesel Fuel?

Energy Technology Data Exchange (ETDEWEB)

None

2014-01-01

Biodiesel, a renewable fuel produced from animal fats or vegetable oils, is popular among many vehicle owners and fleet managers seeking to reduce emissions and support U.S. energy security. Questions sometimes arise about the viability of fueling vehicles with straight vegetable oil (SVO), or waste oils from cooking and other processes, without intermediate processing. But SVO and waste oils differ from biodiesel (and conventional diesel) in some important ways and are generally not considered acceptable vehicle fuels for large-scale or long-term use.

Production of Biodiesel from Vegetable Oil Using Microware Irradiation

Directory of Open Access Journals (Sweden)

N. Kapilan

2012-01-01

Full Text Available The petroleum oil supply crisis, the increase in demand and the price eruption have led to a search for an alternative fuel of bio-origin in India. Among the alternative fuels, biodiesel is considered as a sustainable renewable alternative fuel to fossil diesel. Non-edible jatropha oil has considerable potential for the production of biodiesel in India. The production of biodiesel from jatropha oil using a conventional heating method takes more than 1h. In this work, microwave irradiation has been used as a source of heat for the transesterification reaction. A domestic microwave oven was modified and used for microwave heating of the reactants. The time taken for biodiesel production using microwave irradiation was 1 min. The fuel property analysis shows that the properties of jatropha oil biodiesel satisfy the biodiesel standards, and are close to the fossil diesel standards. From this work, it is concluded that biodiesel can be produced from vegetable oil using microwave irradiation, with a significant reduction in production time.

Applicability of Vegetable Oils as a Wood Preservative

Directory of Open Access Journals (Sweden)

Eylem Dizman Tomak

2012-04-01

Full Text Available Conventional heavy duty wood preservatives have been banned or restricted for some applications due to their mammalian toxicity and their adverse effect on the environment. New, eco-friendly, but nevertheless still effective protection systems, is needed to protect wood in outdoors. Non-toxic vegetable oils can form of a protective layer on the surface of the wood cells which decrease water uptake of wood. For that reason, oils have a good potential as being a wood preservative. However, impregnation with vegetable oils is insufficient to impart adequate biological decay and termite resistance, and indeed the treatment may increase wood’s propensity to burn. In addition, a high level of oil absorption required for good protection make the process impractical and uneconomic to use. The efficiency of the treatment can be improved with using the biocides and oils together. Beside this, usage of modified oils can decrease the retention levels in wood. In this study, applicability of vegetable oils being one of the environment-friendly, biodegradable water repellents on wood treatments was reported. Furthermore, problems related to the use of oils for wood protection, and possible solutions for the problems were discussed.In this study, applicability of vegetable oils as one of the environment-friendly, biodegradable water repellents was reported. Furthermore, problems related to the use of oils for wood protection and possible solutions for the problems were discussed

Determination of the physical characteristics of vegetable oils

Energy Technology Data Exchange (ETDEWEB)

Andrade, Danielle Oliveira de; Andrade, Ednilton Tavares de; Pereira, Roberto Guimaraes [Universidade Federal Fluminense (TER/UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Agricola e do Meio Ambiente; Tulcan, Oscar Edwin Piamba [Universidade Nacional da Colombia (UNAL), Bogota (Colombia). Fac de Ingenieria

2008-07-01

The objective of this work was the characterization of vegetable oils of canola, sunflower, corn and soybean through corrosion, kinematic viscosity, density, cloud point and flow point tests. Vegetable oils are used as raw material for preparation of biofuels or as fuel diesel additive or substitute. The vegetable oils tested showed a low level of corrosion, kinematic viscosities are measured in the range of 31 to 36 mm{sup 2}.s{sup -1}, density was tested at 15 and 20 deg C and showed results varying in the third decimal order. For the oils tested, the cloud point is around 0 deg C and the flow point around -17 deg C. (author)

EFFECT OF VARIOUS VEGETABLE OILS ON THE LIPID PROFILE AND ANTIOXIDANT STATUS IN HYPERCHOLESTEROLAEMIC WISTAR RATS- A COMPARATIVE STUDY

Directory of Open Access Journals (Sweden)

Prasad Ravindra Manjeshwar

2017-02-01

addition of vegetable oils showed a positive influence on lipid metabolism in hypercholesterolaemic rats. Among the vegetable oils, coconut oil was found to be beneficial as it has more antioxidant property. These findings can provide useful information regarding the choice of vegetable oils in hypercholesterolaemic patients in future.

Recent developments in microbial oils production: a possible alternative to vegetable oils for biodiesel without competition with human food?

Directory of Open Access Journals (Sweden)

Gwendoline Christophe

2012-02-01

Full Text Available Since centuries vegetable oils are consumed as human food but it also finds applications in biodiesel production which is attracting more attention. But due to being in competition with food it could not be sustainable and leads the need to search for alternative. Nowdays microbes-derived oils (single cell oils seem to be alternatives for biodiesel production due to their similar composition to that of vegetable oils. However, the cold flow properties of the biodiesel produced from microbial oils are unacceptable and have to be modified by an efficient transesterification. Glycerol which is by product of transesterification can be valorised into some more useful products so that it can also be utilised along with biodiesel to simplify the downstream processing. The review paper discusses about various potent microorganisms for biodiesel production, enzymes involved in the lipid accumulation, lipid quantification methods, catalysts used in transesterification (including enzymatic catalyst and valorisation of glycerol.

Replacement of dietary fish oil with vegetable oils improves the growth and flesh quality of large yellow croaker ( Larmichthys crocea)

Science.gov (United States)

Duan, Qingyuan; Mai, Kangsen; Shentu, Jikang; Ai, Qinghui; Zhong, Huiying; Jiang, Yujian; Zhang, Lu; Zhang, Chunxiao; Guo, Sitong

2014-06-01

We investigated the effect of the replacement of dietary fish oil with vegetable oils on the growth and flesh quality of large yellow croaker ( Larmichthys crocea). The basal diet (FO) was formulated to contain 66.5% fish meal and 6.4% menhaden fish oil; whereas the other 3 experimental diets were formulated by replacing the fish oil with 50% soybean oil (SO50), 100% soybean oil (SO100) and 100% palm oil (PO100), respectively. The 4 diets were randomly assigned to 4 floating sea cages (3.0 m × 3.0 m × 3.0 m), and each was stocked with 250 fish individuals with an initial average weight of 245.29 g ± 7.45 g. The fish were fed to apparent satiation twice a day at 5:00 and 17:00, respectively, for 12 weeks. Experimental analysis showed that the specific growth rate of fish fed SO50 or PO100 were significantly higher than that of fish fed FO or SO100 ( P0.05). Compared to FO diet, SO50, SO100 and PO100 diets led to substantial decreases in the liquid loss and water loss from fresh fillets (1 d, 4°C) ( Preplacement of fish oil with vegetable oils. These findings indicated that the growth performance and selected flesh quality properties (liquid holding capacity and TBARS value) of large yellow croaker were substantially improved by replacing dietary fish oil with vegetable oils.

Determination Of Adsorption And Paraffin Characterization Of Treatment To Adsorb Vegetable Oil

International Nuclear Information System (INIS)

Aminah, Neneng Siti; Mulijani, Sri; Sudirman; Ridwan

2004-01-01

Using vegetable oil repeatedly, beside affect on quality decline of food and the oil itself, it is harmful to human health. Some poisoning and carcinogenic symptom were founded with experiment using animals. According to that fact, the aim of the research is using paraffin and candle to adsorb used vegetable oil and to convert into solid sample, so it can be easily wasted. At first, 2 g of sample was poured into the heated oil, with gently stirrer until it turned cold and harden. Each sample and standard before and after treatment was characterized with Ftir, XRD, and DSc. The result shows that paraffins adsorbs 40 ml used vegetable oil with 2 g sample in proportion. That proportion is lower than the standard which can adsorb 66.67 ml vegetable oil in the same weight sample. The difference of paraffin and standard is caused by physical properties within that two materials, and it can be explained by Ftir, X-Ray Diffraction (XRD) and differential scanning calorimetry (DSc). Based on result of Ftir analysis, standard consented of saturated hydrocarbon compound (alkanes) whereas paraffin consisted of unsaturated hydrocarbon compound (alkenes). Infrared spectrum after treatment showed the changes of compound, O-H and esters group were formed and it shows characterised the adsorption process. The result of DSc analysis showed that crystalline the melting point of standard is 75,3 o C and paraffin is 54,17 o C. The result of analysis XRD, described that standard and paraffin before treatment are crystalline whereas after treatment are am orf

A detection method of vegetable oils in edible blended oil based on three-dimensional fluorescence spectroscopy technique.

Science.gov (United States)

Xu, Jing; Liu, Xiao-Fei; Wang, Yu-Tian

2016-12-01

Edible blended vegetable oils are made from two or more refined oils. Blended oils can provide a wider range of essential fatty acids than single vegetable oils, which helps support good nutrition. Nutritional components in blended oils are related to the type and content of vegetable oils used, and a new, more accurate, method is proposed to identify and quantify the vegetable oils present using cluster analysis and a Quasi-Monte Carlo integral. Three-dimensional fluorescence spectra were obtained at 250-400nm (excitation) and 260-750nm (emission). Mixtures of sunflower, soybean and peanut oils were used as typical examples to validate the effectiveness of the method. Copyright © 2016 Elsevier Ltd. All rights reserved.

Influence of Brazilian vegetable oils on mechanical resistence of hair fiber

Directory of Open Access Journals (Sweden)

Maria Valéria Velasco

2015-02-01

Full Text Available Associating the global trend of incorporating active compounds and plants in cosmetic formulations and the vast Brazilian biodiversity, the present work aimed to study the incorporation of Brazilian vegetable oils in hair conditioner formulations, evaluating the mechanical resistance of hair fibers. The following oils were incorporated into base formulations at 5.0 % (w/w: babassu, buriti, andiroba and pequi. The formulations were applied to samples of Caucasian hair, followed by several washing steps, then the evaluation of mechanical strength. It was found that there was no statistically significant difference in mechanical resistance between samples treated with oils and the control between the first and seventh wash cycles. This fact can be explained by the possible low penetration of oils into the cortex, a region responsible for the mechanical properties of the hair fiber, since the grease composition disfavors its diffusion. The common effects of vegetable oils on the cuticle, such as filling in cracks or cavities, lubrication, and increased protein hydrophobicity cannot be excluded. The oils tested in this work were not able to raise or protect hair tresses. However, additional studies are required in order to establish the effects of oil treatments, particularly in damaged hair.

The potential of using vegetable oil fuels as fuel for diesel engines

International Nuclear Information System (INIS)

Altin, Recep; Cetinkaya, Selim; Yucesu, Huseyin Serdar

2001-01-01

Vegetable oils are produced from numerous oil seed crops. While all vegetable oils have high energy content, most require some processing to assure safe use in internal combustion engines. Some of these oils already have been evaluated as substitutes for diesel fuels. The effects of vegetable oil fuels and their methyl esters (raw sunflower oil, raw cottonseed oil, raw soybean oil and their methyl esters, refined corn oil, distilled opium poppy oil and refined rapeseed oil) on a direct injected, four stroke, single cylinder diesel engine performance and exhaust emissions was investigated in this paper. The results show that from the performance viewpoint, both vegetable oils and their esters are promising alternatives as fuel for diesel engines. Because of their high viscosity, drying with time and thickening in cold conditions, vegetable oil fuels still have problems, such as flow, atomisation and heavy particulate emissions. (Author)

The potential of using vegetable oil fuels as fuel for diesel engines

Energy Technology Data Exchange (ETDEWEB)

Altin, Recep [Ministry of Education, Projects Coordination Unit, Ankara (Turkey); Cetinkaya, Selim [Gazi Univ., Technical Education Faculty, Ankara (Turkey); Yucesu, Huseyin Serdar [Karaelmas Univ., Technical Education Faculty, Karabuk (Turkey)

2001-03-01

Vegetable oils are produced from numerous oil seed crops. While all vegetable oils have high energy content, most require some processing to assure safe use in internal combustion engines. Some of these oils already have been evaluated as substitutes for diesel fuels. The effects of vegetable oil fuels and their methyl esters (raw sunflower oil, raw cottonseed oil, raw soybean oil and their methyl esters, refined corn oil, distilled opium poppy oil and refined rapeseed oil) on a direct injected, four stroke, single cylinder diesel engine performance and exhaust emissions was investigated in this paper. The results show that from the performance viewpoint, both vegetable oils and their esters are promising alternatives as fuel for diesel engines. Because of their high viscosity, drying with time and thickening in cold conditions, vegetable oil fuels still have problems, such as flow, atomisation and heavy particulate emissions. (Author)

Influence of vegetable oils fatty acid composition on reaction temperature and glycerides conversion to biodiesel during transesterification.

Science.gov (United States)

Pinzi, S; Gandía, L M; Arzamendi, G; Ruiz, J J; Dorado, M P

2011-01-01

Presence of unreacted glycerides in biodiesel may reduce drastically its quality. This is why conversion of raw material in biodiesel through transesterification needs to readjust reaction parameter values to complete. In the present work, monitoring of glycerides transformation in biodiesel during the transesterification of vegetable oils was carried out. To check the influence of the chemical composition on glycerides conversion, selected vegetable oils covered a wide range of fatty acid composition. Reactions were carried out under alkali-transesterification in the presence of methanol. In addition, a multiple regression model was proposed. Results showed that kinetics depends on chemical and physical properties of the oils. It was found that the optimal reaction temperature depends on both length and unsaturation degree of vegetable oils fatty acid chains. Vegetable oils with higher degree of unsaturation exhibit faster monoglycerides conversion to biodiesel. It can be concluded that fatty acid composition influences reaction parameters and glycerides conversion, hence biodiesel yield and economic viability. Copyright © 2010 Elsevier Ltd. All rights reserved.

Evaluating lubricating capacity of vegetal oils using Abbott-Firestone curve

Science.gov (United States)

Georgescu, C.; Cristea, G. C.; Dima, C.; Deleanu, L.

2017-02-01

The paper presents the change of functional parameters defined on the Abbott-Firestone curve in order to evaluate the surface quality of the balls from the four ball tester, after tests done with several vegetable oils. The tests were done using two grades of rapeseed oil (degummed and refined) and two grades of soybean oil (coarse and degummed) and a common transmission oil (T90). Test parameters were 200 N and 0.576 m/s (1500 rpm) for 60 minutes. For the refined rapeseed oil, the changes in shape of the Abbott-Firestone curves are more dramatic, these being characterized by high values of Spk (the average value for the wear scars on the three balls), thus being 40% of the sum Svk + Sk + Spk, percentage also obtained for the soybean oil, but the value Spk being lower. For the degummed soybean oil, the profile height of the wear scars are taller than those obtained after testing the coarse soybean oil, meaning that the degumming process has a negative influence on the worn surface quality and the lubricating capacity of this oil. Comparing the surface quality of the wear scars on fixed tested balls is a reliable method to point out the lubricant properties of the vegetable oils, especially if they are compared to a “classical” lubricant as a non-additivated transmission mineral oil T90. The best surface after testing was obtained for the soybean oil, followed by T90 oil and the degummed grades of the soybean oil and rapeseed oil (these three giving very close values for the functional parameters), but the refined rapeseed oil generated the poorest quality of the wear scars on the balls, under the same testing conditions.

The use of Brazilian vegetable oils in nanoemulsions: an update on preparation and biological applications

Directory of Open Access Journals (Sweden)

Lisiane Bajerski

Full Text Available ABSTRACT Vegetable oils present important pharmacological properties, which gained ground in the pharmaceutical field. Its encapsulation in nanoemulsions is considered a promising strategy to facilitate the applicability of these natural compounds and to potentiate the actions. These formulations offer several advantages for topical and systemic delivery of cosmetic and pharmaceutical agents including controlled droplet size, protection of the vegetable oil to photo, thermal and volatilization instability and ability to dissolve and stabilize lipophilic drugs. For these reasons, the aim of this review is to report on some characteristics, preparation methods, applications and especially analyze recent research available in the literature concerning the use of vegetable oils with therapeutic characteristics as lipid core in nanoemulsions, specially from Brazilian flora, such as babassu (Orbignya oleifera, aroeira (Schinus molle L., andiroba (Carapa guaianiensis, casca-de-anta (Drimys brasiliensis Miers, sucupira (Pterodon emarginatus Vogel and carqueja doce (Stenachaenium megapotamicum oils.

Non-conventional use of vegetable oils: Possibilities and prospects

International Nuclear Information System (INIS)

Pellizzi, G.

1992-01-01

This paper examines the feasibility, relative to the specific capabilities of the Italian agricultural industry, of the production of biomass fuels and lubricating oils. A comparative cost benefit analysis is made to determine the technical and economic convenience of the production of grain or vegetable oil derived biomass for direct use as lubricants, fuel oils or for conversion into ethanol fuels. The suitability of different types of engines is examined for the direct combustion of vegetable oils and for the combustion of ethanol fuels. The study also has a look at what should be the suitable mix of Italian Government agricultural, environmental and fiscal strategies to support and encourage the production and use of industrial vegetable fuel oils and lubricants

Caracterización de una biograsa de aceite vegetal de Jatropha curcas L y jabón de litio//Characterization of biogrease based on Jatropha curcas L vegetable oil and Lithium Soap Thickener

Directory of Open Access Journals (Sweden)

Juliano Chitue de Assunção Nascimento

2013-05-01

Full Text Available Los aceites vegetales poseen un gran potencial como fluido base y como sustituto de los aceites minerales para la formulación de grasas lubricantes, estos aceites son biodegradables y renovables. En el trabajo se determinaron las propiedades  fisicoquímicas, antidesgaste y de extrema presión de una biograsa de aceite vegetal de Jatropha curcas L y jabón de litio empleando los métodos de pruebas estándar para las grasas lubricantes. La biograsa posee un color amarillo claro, una textura suave y homogénea,  un grado de penetración NLGI 1, una temperatura de goteo de 145 oC, magnitudes adecuadas del contenido de álcalis libre y corrosión al cobre; así como  propiedades antidesgaste y de extrema presión similares a otras grasas minerales y biograsas formuladas con diferentes aceites vegetales. Palabras claves: biograsa, aceite de Jatropha curcas L, jabón de litio, propiedades fisicoquímicas, propiedades antidesgaste, propiedades de extrema presión. Characterization of biogrease based on Jatropha curcas L vegetable oil and Lithium Soap Thickener. Abstract Vegetable oils have a great potential as a base fluid and a substitute for mineral oil in grease formulation, these oils are biodegradable and renewable. In this paper were determined the  physicochemical, antiwear and extreme pressure properties of a biogrease based on Jatropha curcas L vegetable oil and lithium soap thickener using the lubricanting greases standard test methods. The biogrease have a light yellow color, soft and homogeneous texture, a penetration grade NLGI 1, a drop point of 145 oC, appropriate magnitudes of free alkalis and copper corrosion; as well as antiwear and extreme pressure properties similar to the other mineral lubricating grease and formulated biogreases with differents vegetable oils. Key words: biogrease, Jatropha curcas L vegetable oil, lithium soap thickener, physicochemical properties, antiwear properties, extreme pressure properties.

Synthesis of epoxidized cardanol and its antioxidative properties for vegetable oils and biodiesel

Science.gov (United States)

A novel antioxidant epoxidized cardanol (ECD), derived from cardanol, was synthesized and characterized by FT-IR, 1H-NMR and 13C-NMR. Oxidative stability of ECD used in vegetable oils and biodiesel was evaluated by pressurized differential scanning calorimetry (PDSC) and the Rancimat method, respect...

Interaction between vegetable oil based plasticizer molecules and polyvinyl chloride, and their plasticization effect

Science.gov (United States)

Haryono, Agus; Triwulandari, Evi; Jiang, Pingping

2017-01-01

Plasticizer molecules are low molecular weight compounds that are widely used in polymer industries especially in polyvinyl chloride (PVC) resin. As an additive in PVC resin, the important role of plasticizer molecules is to improve the flexibility and processability of PVC by lowering the glass transition temperature (Tg). However, the commercial plasticizer like di(2-ethylhexyl)phthalate (DEHP) is known to cause liver cancer, at least in laboratory rats. DEHP can leach out from PVC into blood, certain drug solutions and fatty foods, which has been detected in the bloodstream of patients undergoing transfusion. Vegetable oil based plasticizers have some attractive properties such as non-toxic, bio-degradable, good heat and light stability, renewable resources, and environmentally friendly. Here we discussed the main results and development of vegetable oil based plasticizer, and especially palm oil based plasticizer. The interaction between plasticizer and polymer was discussed from the properties of the plasticized polymeric material.

Authentication of edible vegetable oils adulterated with used frying oil by Fourier Transform Infrared Spectroscopy.

Science.gov (United States)

Zhang, Qing; Liu, Cheng; Sun, Zhijian; Hu, Xiaosong; Shen, Qun; Wu, Jihong

2012-06-01

The application of Fourier Transform Infrared (FTIR) Spectroscopy to authenticate edible vegetable oils (corn, peanut, rapeseed and soybean oil) adulterated with used frying oil was introduced in this paper. The FTIR spectrum of oil was divided into 22 regions which corresponded to the constituents and molecular structures of vegetable oils. Samples of calibration set were classified into four categories for corn and peanut oils and five categories for rapeseed and soybean oils by cluster analysis. Qualitative analysis of validation set was obtained by discriminant analysis. Area ratio between absorption band 19 and 20 and wavenumber shift of band 19 were treated by linear regression for quantitative analysis. For four adulteration types, LODs of area ratio were 6.6%, 7.2%, 5.5%, 3.6% and wavenumber shift were 8.1%, 9.0%, 6.9%, 5.6%, respectively. The proposed methodology is a useful tool to authenticate the edible vegetable oils adulterated with used frying oil. Copyright © 2011 Elsevier Ltd. All rights reserved.

Selection of surfactants for using in invert emulsion based on vegetable oil; Selecao de surfactantes para uso em emulsoes inversas a base de oleo vegetal

Energy Technology Data Exchange (ETDEWEB)

Silva, Giliane V.; Lacerda, Vanessa M.; Garcia, Rosangela B.; Costa, Marta [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil). Lab. de Pesquisa em Petroleo (LAPET); Girao, Joaquim Helder S. [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2004-07-01

The purpose of this study was to investigate the superficial properties of a vegetable oil of degree nutritious front the several biodegradable surfactants, seeking to stabilize emulsions of the type water-in-oil, presents in formulations of fluids of perforation of oleofilic base. Mentioned them fluids they are suitable to the perforation of located oil wells in leases of high environmental sensibility and with inferior temperature to 250 deg F. The use of a fluid of that nature can make possible the discard of the solids perforated directly in the sea, sparing the application of previous treatments, or the transport of the same ones for dike-mother, operations that you/they can elevate the total cost of the perforation. The values of the superficial tension and of the concentration critical micellar, they were measured in the solutions oil vegetal/tensoactive, through the method of the ring (DuNouy), using a tensiometer DCA 315 (Thermo Cahn). The effects of the variation of the concentration and of the temperature in the superficial properties of the oil were certain. (author)

Preparation of function-enhanced vegetable oils

Directory of Open Access Journals (Sweden)

Hiroshi Maeda

2016-01-01

Full Text Available Background: Previously, we (HM found that most commercially available edible oils, which were processed by hexane extraction followed by a number of purification steps, were extremely low in anti-peroxy radical (ROO., or radical scavenging activity. This is a great contrast to the respective virgin oils as exemplified by extra-virgin olive oil or crude rape seed oil [1-4] (Figure 1. Therefore, such highly purified oils will became prooxidant and less desirable food components in terms of health oriented diet. Oxidized oils may eventually cause DNA cleavages, modification of proteins, RNA, and lipids, as well as cellular damage, or promote inflammation and carcinogenesis at later time [5-9]. These commercial oils of low antioxidant activity may be improved by adding functionally effective antioxidative components, by using dried vegetable-waste such as tomato-juice-waste-residues and wine-ferment-waste-residues. Their antioxiative components will be transferred into the functionally poor grade edible oils, and consequently, one can improve the quality of such functionally poor oils and thereby contributing human health [2,8,9]. The purpose of this paper is to report a practical procedure to fortify functionally low grade conventional edible oils to functionally enriched edible oils using dried vegetable-waste residues such as tomato juice waste, and wine-ferment-residues, or other vegetable-waste residues. Methods: (1 Preparation and measurements of lycopene and carotenoid enriched oils. To 5.0g or 1.0g of the dried residue of tomato juice waste, 100ml of commercial rape seed (canola oil was added respectively. Each mixture was incubated at room temperature in dark for several weeks. Amount of lycopene and carotenoids extracted into the oil was monitored by increase of absorption (400-550nm and fluorescence at 470nm of carotenoid. Grape-juice ferment (wine waste was similarly prepared after hot air drying, and immersed in canola oil. (2

Vegetable oils as lube basestocks: A review | Srivastava | African ...

African Journals Online (AJOL)

Vegetable oils are promising candidates as base fluid for eco-friendly lubricants because of their excellent lubricity, biodegradability, viscosity-temperature characteristics and low volatility. In view of agriculture based Indian economy, there is a great potential of producing vegetable oil based lubricants, which has ecological ...

Fast-HPLC Fingerprinting to Discriminate Olive Oil from Other Edible Vegetable Oils by Multivariate Classification Methods.

Science.gov (United States)

Jiménez-Carvelo, Ana M; González-Casado, Antonio; Pérez-Castaño, Estefanía; Cuadros-Rodríguez, Luis

2017-03-01

A new analytical method for the differentiation of olive oil from other vegetable oils using reversed-phase LC and applying chemometric techniques was developed. A 3 cm short column was used to obtain the chromatographic fingerprint of the methyl-transesterified fraction of each vegetable oil. The chromatographic analysis took only 4 min. The multivariate classification methods used were k-nearest neighbors, partial least-squares (PLS) discriminant analysis, one-class PLS, support vector machine classification, and soft independent modeling of class analogies. The discrimination of olive oil from other vegetable edible oils was evaluated by several classification quality metrics. Several strategies for the classification of the olive oil were used: one input-class, two input-class, and pseudo two input-class.

Natural Organochlorines as Precursors of 3-Monochloropropanediol Esters in Vegetable Oils.

Science.gov (United States)

Tiong, Soon Huat; Saparin, Norliza; Teh, Huey Fang; Ng, Theresa Lee Mei; Md Zain, Mohd Zairey Bin; Neoh, Bee Keat; Md Noor, Ahmadilfitri; Tan, Chin Ping; Lai, Oi Ming; Appleton, David Ross

2018-01-31

During high-temperature refining of vegetable oils, 3-monochloropropanediol (3-MCPD) esters, possible carcinogens, are formed from acylglycerol in the presence of a chlorine source. To investigate organochlorine compounds in vegetable oils as possible precursors for 3-MCPD esters, we tested crude palm, soybean, rapeseed, sunflower, corn, coconut, and olive oils for the presence of organochlorine compounds. Having found them in all vegetable oils tested, we focused subsequent study on oil palm products. Analysis of the chlorine isotope mass pattern exhibited in high-resolution mass spectrometry enabled organochlorine compound identification in crude palm oils as constituents of wax esters, fatty acid, diacylglycerols, and sphingolipids, which are produced endogenously in oil palm mesocarp throughout ripening. Analysis of thermal decomposition and changes during refining suggested that these naturally present organochlorine compounds in palm oils and perhaps in other vegetable oils are precursors of 3-MCPD esters. Enrichment and dose-response showed a linear relationship to 3-MCPD ester formation and indicated that the sphingolipid-based organochlorine compounds are the most active precursors of 3-MCPD esters.

Experimental and theoretical study of the influence of water on hydrolyzed product formation during the feruloylation of vegetable oil.

Science.gov (United States)

Compton, David L; Evans, Kervin O; Appell, Michael

2017-07-01

Feruloylated vegetable oil is a valuable green bioproduct that has several cosmeceutical applications associated with its inherent anti-oxidant and ultraviolet-absorption properties. Hydrolyzed vegetable oil by-products can influence product quality and consistency. The formation of by-products by residual water in the enzymatic synthesis of feruloylated vegetable oil was investigated using chemical theory and experimental studies by monitoring the reaction over a 22-day period. The hydrolysis of vegetable oil is thermodynamically favored over the hydrolysis of the ethyl ferulate starting material. These results suggest that hydrolyzed vegetable oil products will be experimentally observed in greater concentrations compared to hydrolyzed ethyl ferulate products. Quantum chemical studies identified several reaction mechanisms that explain the formation of side products by water, suggesting that residual water influences product quality. Efforts to reduce residual water can improve product consistency and reduce purification costs. Published 2016. This article is a U.S. Government work and is in the public domain in the USA. Published 2016. This article is a U.S. Government work and is in the public domain in the USA.

A novel quantitative analysis method of three-dimensional fluorescence spectra for vegetable oils contents in edible blend oil

Science.gov (United States)

Xu, Jing; Wang, Yu-Tian; Liu, Xiao-Fei

2015-04-01

Edible blend oil is a mixture of vegetable oils. Eligible blend oil can meet the daily need of two essential fatty acids for human to achieve the balanced nutrition. Each vegetable oil has its different composition, so vegetable oils contents in edible blend oil determine nutritional components in blend oil. A high-precision quantitative analysis method to detect the vegetable oils contents in blend oil is necessary to ensure balanced nutrition for human being. Three-dimensional fluorescence technique is high selectivity, high sensitivity, and high-efficiency. Efficiency extraction and full use of information in tree-dimensional fluorescence spectra will improve the accuracy of the measurement. A novel quantitative analysis is proposed based on Quasi-Monte-Carlo integral to improve the measurement sensitivity and reduce the random error. Partial least squares method is used to solve nonlinear equations to avoid the effect of multicollinearity. The recovery rates of blend oil mixed by peanut oil, soybean oil and sunflower are calculated to verify the accuracy of the method, which are increased, compared the linear method used commonly for component concentration measurement.

Taxonomic perspective of plant species yielding vegetable oils used ...

African Journals Online (AJOL)

A search conducted to determine the plants yielding vegetable oils resulted in 78 plant species with potential use in cosmetics and skin care products. The taxonomic position of these plant species is described with a description of vegetable oils from these plants and their use in cosmetic and skin care products.

Production of biodiesel from vegetable oils

Directory of Open Access Journals (Sweden)

Luque, Susana

2008-03-01

Full Text Available Biodiesel is produced by transesterification of triglycerides present in animal fat or vegetable oils, by displacing glycerine with a low molar mass alcohol. This resulting ester mixture has physico-chemical properties similar to those of petroleum diesel. This paper reviews the synthetic paths that lead to biodiesel by means of the catalytic transesterification of vegetable oils. Although methyl esters are at present the only ones produced at industrial scale, the use of ethanol, which can also be obtained from renewable resources, has been considered, since it would generate a cleaner and more biocompatible fuel.El biodiésel se produce mediante la transesterificación de triglicéridos, presentes en grasas animales o aceites vegetales, en un proceso en el que un alcohol de bajo peso molecular desplaza a la glicerina. La mezcla de esteres así resultante posee unas propiedades físico-químicas similares a las del diésel procedente de petróleo. En este artículo se revisan las vías de síntesis de biodiésel mediante la transesterificación catalítica de aceites vegetales. Aunque actualmente a escala industrial solo se producen ésteres metílicos, también se ha considerado el uso de etanol, ya que éste se obtiene también de fuentes renovables, generando así un combustible más limpio y biocompatible.

Vegetable oils as fuels and lubrificants: Commercialization problematics

International Nuclear Information System (INIS)

Bartolelli, V.

1992-01-01

The aim of this paper is to assess the commercialization feasibility of vegetable oils as industrial fuels and lubricants. The paper also discusses what should be the suitable mix of Italian Government agricultural, environmental and fiscal strategies to support and encourage the production and use of industrial vegetable fuel oils and lubricants. It points out the main advantages of bio-fuel oils - they are much less polluting than conventional fossil fuel oils and can be produced domestically, thus reducing national dependency on foreign energy imports and increasing employment opportunities. The major obstacle to their development is identified as being the creation of suitable pricing and fiscal policies in harmony with traditional energy markets

Determination of lipid oxidation products in vegetable oils and marine omega-3 supplements.

Science.gov (United States)

Halvorsen, Bente Lise; Blomhoff, Rune

2011-01-01

There is convincing evidence that replacing dietary saturated fats with polyunsaturated fats (PUFA) decreases risk of cardiovascular diseases. Therefore, PUFA rich foods such as vegetable oils, fatty fish, and marine omega-3 supplements are recommended. However, PUFA are easily oxidizable and there is concern about possible negative health effects from intake of oxidized lipids. Little is known about the degree of lipid oxidation in such products. To assess the content of lipid oxidation products in a large selection of vegetable oils and marine omega-3 supplements available in Norway. Both fresh and heated vegetable oils were studied. A large selection of commercially available vegetable oils and marine omega-3 supplements was purchased from grocery stores, pharmacies, and health food stores in Norway. The content of lipid oxidation products were measured as peroxide value and alkenal concentration. Twelve different vegetable oils were heated for a temperature (225°C) and time (25 minutes) resembling conditions typically used during cooking. The peroxide values were in the range 1.04-10.38 meq/kg for omega-3 supplements and in the range 0.60-5.33 meq/kg for fresh vegetable oils. The concentration range of alkenals was 158.23-932.19 nmol/mL for omega-3 supplements and 33.24-119.04 nmol/mL for vegetable oils. After heating, a 2.9-11.2 fold increase in alkenal concentration was observed for vegetable oils. The contents of hydroperoxides and alkenals in omega-3 supplements are higher than in vegetable oils. After heating vegetable oils, a large increase in alkenal concentration was observed.

Undesirable substances in vegetable oils: anything to declare?

Directory of Open Access Journals (Sweden)

Lacoste Florence

2014-01-01

Full Text Available The presence of undesirable compounds in vegetable and animal oils and fats may have many different origins. Although the potential toxicity of most of these undesirable compounds is real, poisoning risks are rather limited due to the efficient elimination during oil-refining steps, careful conditioning, choice of efficient packaging and industrial quality control management. However the research of contaminants is part of multiple controls conducted by fat and oil industry to verify the conformity of products placed on the market in relation to regulations such as the European commission regulation EC No. 1881/2006 setting maximum levels for some contaminants in food as lead, some mycotoxins, dioxins, polychlorobiphenyls, benzo[a]pyrene. In the absence of regulation, the detection of contaminants must be addressed in partnership with authorities according to the toxicity of molecules. The controls are not confined to environmental contaminants. They also include compounds that can be formed during the production process of vegetable oils such as esters of 3-monochloropropanediol. This article focuses more particularly on heavy metals, polycyclic aromatic hydrocarbons, mineral oils, phthalates and 3-MCPD or glycidyl esters. Aspects such as methods for analysis, limits fixed by EC regulation and occurrence in vegetable oils are discussed.

Genetically engineered plants with increased vegetative oil content

Science.gov (United States)

Benning, Christoph

2017-05-23

The invention relates to genetically modified agricultural plants with increased oil content in vegetative tissues, as well as to expression systems, plant cells, seeds and vegetative tissues related thereto.

Operation variables in transesterification of vegetable oil: an enzymatic catalysis review

Directory of Open Access Journals (Sweden)

Andrés Felipe Rojas González

2010-01-01

Full Text Available This paper presents the results of a literature review regarding how operating conditions influence vegetable oil enzymatic transesterification yield. The following parameters were studied: temperature and time reaction, alcohol: oil molar ratio, alcohol type, biocatalyst type and concentration, solvent, mixed intensity, reagent purity and free fatty acid and moisture concentration. Yields greater than 90% can be achieved in the enzymatic catalyst of vegetable oil using 35-50°C temperatures, long time reactions (7- 90h and a 3:1alcohol: vegetable oil molar ratio; however, such values would intrinsically depend on the type of lipase and oil u- sed. It was also found that free fatty acid and moisture concentration were parameters which did not require rigorous control due to high enzyme specificity. Lipases immobilised from Pseudomona cepacia bacteria and Rhizopus orizae fungi were most used in vegetable oil enzymatic transesterification.

Macauba: a promising tropical palm for the production of vegetable oil

Directory of Open Access Journals (Sweden)

Colombo Carlos Augusto

2018-01-01

Full Text Available The growing global demand for vegetable oils for food and for replacing fossil fuels leads to increased oilseeds production. Almost 122 of the current 187 million tons of vegetable oils produced in the world correspond to palm and soybean oils. The oil palm is cultivated in the tropical zone, in areas formerly occupied by forests, and soybean oil is a by-product of protein meal production. The diversification of raw materials for the vegetable oil market is thus strategic for both food and non-food sectors. Sources for vegetable oil should be economically competitive and provide sustainability indexes higher than that provided by oil palm and soybean. In this context, we describe the potential of Acrocomia aculeata, popularly known as macauba. Macauba is an American palm from the tropical zones which presents oil productivity and quality similar to that of the oil palm. It grows spontaneously in a wide range of environments and it is not very water demanding. Macauba palm has a high potential for oil production and for diversification of co-products with some potential of value aggregation. Such a perennial and sustainable species will probably fulfill the requirements to become an important new commercial oilseed crop.

Development of building blocks using vegetable oil and recycled aggregate

Directory of Open Access Journals (Sweden)

Attia Mohamed I.

2017-01-01

Full Text Available The primary objective of this research was to contribute towards greater sustainability of the construction industry in the Qatar by proposing methods to reduce its dependency on primary imported materials. In this investigation, recycled and secondary aggregates (RSA were combined with non-traditional binders to develop a unique method of manufacturing construction and building blocks. Following an extensive phase of laboratory trials and experimentation, it was realised that many types of graded mineral aggregates, when mixed with vegetable oils (virgin or waste at optimal proportions, then compacted and thermally cured at elevated temperatures can readily generate hardened composites that have the mechanical characteristics of conventional building blocks. The resultant blocks have been named “Vegeblocks” and are viewed as viable alternatives to conventional concrete blocks. Furthermore, the research has demonstrated the feasibility of producing Vegeblocks composed of 100% recycled aggregate and discarded waste cooking oil. Based on physical and mineralogical properties, each type of aggregate has an optimum oil content for maximum compressive strength, beyond which, any additional oil will result in reduction in mechanical properties. Acceptable compressive strength values were achieved by thermally curing Vegeblocks at of 170 °C for 24 hours.

Comparative evaluation of physicochemical properties of jatropha curcas seed oil for coolant-lubricant application

Science.gov (United States)

Murad, Muhamad Nasir; Sharif, Safian; Rahim, Erween Abd.; Abdullah, Rozaini

2017-09-01

Increased attention to environmental issues due to industrial activities has forced the authorities raise awareness and implement regulations to reduce the use of mineral oil. Some vegetable oils unexplored or less explored, particularly the non-edible oils such as Jatropha curcas oil (JCO) and others. Physicochemical properties of JCO is compared with others edible oils, synthetic ester and fatty alcohol to obtain a viable alternative in metal cutting fluids. The oil was found to show the suitability of properties for coolant-lubricant applications in term of its physicochemical properties and better in flash point and viscosity value.

Vegetable oils in the agriculture. Experience reports; Pflanzenoel als Kraftstoff in der Landwirtschaft. Erfahrungsberichte

Energy Technology Data Exchange (ETDEWEB)

Kemnitz, Dietmar [Fachagentur Nachwachsende Rohstoffe e.V., Guelzow (Germany); Paul, Nicole [Fachagentur Nachwachsende Rohstoffe e.V., Guelzow (Germany); WPR COMMUNICATION GmbH und Co. KG, Koenigswinter/Bonn (Germany); Wichmann, Volker; Schuemann, Ulrike [Rostock Univ. (Germany); Maurer, Karl [Hohenheim Univ. (Germany); Remmele, Edgar [Technologie- und Foerderzentrum Straubing (Germany)

2006-08-15

In the agriculture, bio fuels increasingly meet with great interest. The use of bio diesel and vegetable oil as alternative fuels in diesel engines requires clear technical adjustments. The brochure under consideration reports on realizations of farmers who switched their tractors to an operation with vegetable oils. The brochure consists of the following contributions: (a) Employment of vegetable oil as fuel in the agriculture (empiric reports of farmers); (b) Re-equipment on operation with vegetable oil (empiric reports of reequipping persons); (c) Scientifically accompanying research of re-equipment (results of a 100-tractor-demonstration project); (d) Mixtures of plant oil and diesel fuel (results from engine test stand investigations); (e) Production of vegetable oil (experiences from an oil mill operator); (f) scientifically accompanying research for the production of vegetable oils (references to the production of rapeseed oil fuel according to the standard DIN 51605); (g) Hints and notes for the practice; (h) Fuel filling stations for self-consumers and storage of vegetable oil; (i) FNR funding programs bio fuels in the agriculture; (j) Adresses and contact persons.

Determination of lipid oxidation products in vegetable oils and marine omega-3 supplements

Directory of Open Access Journals (Sweden)

Rune Blomhoff

2011-06-01

Full Text Available Background : There is convincing evidence that replacing dietary saturated fats with polyunsaturated fats (PUFA decreases risk of cardiovascular diseases. Therefore, PUFA rich foods such as vegetable oils, fatty fish, and marine omega-3 supplements are recommended. However, PUFA are easily oxidizable and there is concern about possible negative health effects from intake of oxidized lipids. Little is known about the degree of lipid oxidation in such products. Objective : To assess the content of lipid oxidation products in a large selection of vegetable oils and marine omega-3 supplements available in Norway. Both fresh and heated vegetable oils were studied. Design : A large selection of commercially available vegetable oils and marine omega-3 supplements was purchased from grocery stores, pharmacies, and health food stores in Norway. The content of lipid oxidation products were measured as peroxide value and alkenal concentration. Twelve different vegetable oils were heated for a temperature (225°C and time (25 minutes resembling conditions typically used during cooking. Results : The peroxide values were in the range 1.04–10.38 meq/kg for omega-3 supplements and in the range 0.60–5.33 meq/kg for fresh vegetable oils. The concentration range of alkenals was 158.23–932.19 nmol/mL for omega-3 supplements and 33.24–119.04 nmol/mL for vegetable oils. After heating, a 2.9–11.2 fold increase in alkenal concentration was observed for vegetable oils. Conclusions : The contents of hydroperoxides and alkenals in omega-3 supplements are higher than in vegetable oils. After heating vegetable oils, a large increase in alkenal concentration was observed.

Straight vegetable oil use in Micro-Gas Turbines: System adaptation and testing

International Nuclear Information System (INIS)

Prussi, M.; Chiaramonti, D.; Riccio, G.; Martelli, F.; Pari, L.

2012-01-01

Highlights: → The possibility to feed a Micro Gas Turbine with Straight Vegetable Oil (SVO) has been investigated. → Correlative analysis and CFD were used to model the effect of SVO characteristics on atomization and evaporation. → Minor modifications to a the commercial MGT were adopted. → Measured power output and specific fuel consumption were close to standard fuel, taking into account the LHV of SVO. → Emissions were higher than for standard fossil fuel but strongly affected by SVO temperature. -- Abstract: The aim of this research work is to investigate the use of straight vegetable sunflower oil (SFO), a liquid biofuel, in a Micro-Gas Turbine (MGT). Compared to conventional diesel engines, micro-gas turbines represent a very reliable, clean and performing small scale cogeneration technology. Commercial gas turbines have already been tested with unconventional fuels, such as biomass derived fuels; however, research work on using Straight Vegetable Oil (SVO) as fuel in MGTs are really scarce. The chemical and physical characteristics of SVO are different from fossil diesel oil and rather far from the common technical specifications for gas turbine liquid fuels, not only in terms of kinematic viscosity and Lower Heating Value, but also as regards other issues as contaminant levels and composition, fuel cold properties, ignition properties, etc. Therefore, particular attention has to be given to the atomization and evaporation phases, as these are the most critical steps to achieve stable and efficient long term operation. An analysis based on numerical correlations available from literature was initially adopted for the analysis of the atomization process, supported by CFD modeling to qualitatively investigate the flow pattern. Control parameters were revised and set so to produce a sunflower oil spray having evaporation time comparable to diesel, and minor adaptations to the fuel line were designed and installed on the MGT. Tests with blends and

Biodiesel in Belgium. From rapeseed oil to used vegetable oils

International Nuclear Information System (INIS)

Pelkmans, L.

1997-01-01

There are two motives for the search for alternative motor fuels: reducing the growing pressure of traffic on environment, and looking for a replacement for petrol and diesel oil that are bound to be worn-out in a few decades. A promising alternative motor fuel is biodiesel. The author's institute is involved in its second biodiesel demonstration project. In the first project RME (rapeseed methyl ester) was used undiluted in five passenger cars for two years. There were no technical problems and a clear environmental advantage was noticed. However, the price remains a problem. The use of waste vegetable oils for the production of biodiesel could help to overcome this problem. Therefore, a second biodiesel demonstration project was started in which UVOME (used vegetable oil methyl ester) is used. The preliminary results show a great similarity with the RME results and no technical problems in real life use. 1 fig., 1 tab., 5 refs

Remediation of trichloroethylene-contaminated soils by star technology using vegetable oil smoldering.

Science.gov (United States)

Salman, Madiha; Gerhard, Jason I; Major, David W; Pironi, Paolo; Hadden, Rory

2015-03-21

Self-sustaining treatment for active remediation (STAR) is an innovative soil remediation approach based on smoldering combustion that has been demonstrated to effectively destroy complex hydrocarbon nonaqueous phase liquids (NAPLs) with minimal energy input. This is the first study to explore the smoldering remediation of sand contaminated by a volatile NAPL (trichloroethylene, TCE) and the first to consider utilizing vegetable oil as supplemental fuel for STAR. Thirty laboratory-scale experiments were conducted to evaluate the relationship between key outcomes (TCE destruction, rate of remediation) to initial conditions (vegetable oil type, oil: TCE mass ratio, neat versus emulsified oils). Several vegetable oils and emulsified vegetable oil formulations were shown to support remediation of TCE via self-sustaining smoldering. A minimum concentration of 14,000 mg/kg canola oil was found to treat sand exhibiting up to 80,000 mg/kg TCE. On average, 75% of the TCE mass was removed due to volatilization. This proof-of-concept study suggests that injection and smoldering of vegetable oil may provide a new alternative for driving volatile contaminants to traditional vapour extraction systems without supplying substantial external energy. Copyright © 2014 Elsevier B.V. All rights reserved.

A simplified kinetic and mass transfer modelling of the thermal hydrolysis of vegetable oils

DEFF Research Database (Denmark)

Forero-Hernandez, Hector Alexander; Jones, Mark Nicholas; Sarup, Bent

2017-01-01

This work presents a combined modelling approach to investigate the kinetics and masstransfer effects on the hydrolysis of vegetable oils under subcritical conditions. The primary purpose of this simplified model is to interpret experimental data collected from typical batch tests and to estimate...... parameters for the proposed model. Due to its heterogeneous nature, the hydrolysis reaction is affected not only by the chemical kinetics but also by the rate of mass transfer between the oil and water as well as their specific contact area in this two phase emulsion. Considering these properties, a model...... and improvement accompanied by Monte Carlo uncertainty analysis. Since the lack of experimental data is a crucial issue in the hydrolysis of vegetable oils, this model-based analysis of data is of substantial value to provide necessary information for detailed modeling and characterization of the process....

Photolysis of polychlorinated dibenzo-p-dioxins and dibenzofurans dissolved in vegetable oils: influence of oil quality

International Nuclear Information System (INIS)

Isosaari, Pirjo; Laine, Olli; Tuhkanen, Tuula; Vartiainen, Terttu

2005-01-01

Sunlight or ultraviolet light irradiation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in the presence of vegetable oil offers a potential method for the cleanup of contaminated soil. In this study, the effects of different types of vegetable oils on the photochemical degradation of 1,2,3,4,6,7,8-heptachlorodibenzofuran and heptachlorodibenzo-p-dioxin (1,2,3,4,6,7,8-HpCDF/HpCDD) were investigated in the laboratory. Using a blacklight lamp as a source of ultraviolet light, 93-100% of 1,2,3,4,6,7,8-HpCDF degraded in 60 min in rapeseed oil, extra virgin olive oil and olive oil. Less degradation occurred in palm oil (59%), toluene (39%) and hexane (20%). The better degradation in vegetable oils in comparison with organic solvents was attributed to the photooxidation of lipids producing hydrogen for PCDD/F dechlorination. In addition to the hydrogen donor capacity, permeability of ultraviolet light was involved in the differences between vegetable oils. α-Tocopherol and chlorophyll did not influence the performance of oil at concentrations normally present in vegetable oils, whereas β-carotene had an inhibitory effect on the degradation of 1,2,3,4,6,7,8-HpCDF. Up to 28% of the degradation products of 1,2,3,4,6,7,8-HpCDF were formed via the dechlorination pathway. Products included both toxic (2,3,7,8-chlorinated) and non-toxic PCDD/Fs, the toxic PCDD/Fs being more stable. Irradiation of 1,2,3,4,6,7,8-HpCDD yielded only non-toxic dechlorination products. Polychlorinated hydroxybiphenyls (OH-PCBs), polychlorinated dihydroxybiphenyls (DOH-PCBs) and polychlorinated hydroxydiphenylethers (OH-PCDEs) containing one to seven chlorine atoms were not detected in irradiated HpCDF/HpCDD samples

Photolysis of polychlorinated dibenzo-p-dioxins and dibenzofurans dissolved in vegetable oils: influence of oil quality

Energy Technology Data Exchange (ETDEWEB)

Isosaari, Pirjo [National Public Health Institute, Department of Environmental Health, P.O. Box 95, FI-70701 Kuopio (Finland)]. E-mail: pirjo.isosaari@ktl.fi; Laine, Olli [National Public Health Institute, Department of Environmental Health, P.O. Box 95, FI-70701 Kuopio (Finland); Tuhkanen, Tuula [Tampere University of Technology, Environmental Engineering and Biotechnology, P.O. Box 541, FI-33101 Tampere (Finland); Vartiainen, Terttu [National Public Health Institute, Department of Environmental Health, P.O. Box 95, FI-70701 Kuopio (Finland); University of Kuopio, Department of Environmental Sciences, P.O. Box 1627, Kuopio, FI-70211 Kuopio (Finland)

2005-03-20

Sunlight or ultraviolet light irradiation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in the presence of vegetable oil offers a potential method for the cleanup of contaminated soil. In this study, the effects of different types of vegetable oils on the photochemical degradation of 1,2,3,4,6,7,8-heptachlorodibenzofuran and heptachlorodibenzo-p-dioxin (1,2,3,4,6,7,8-HpCDF/HpCDD) were investigated in the laboratory. Using a blacklight lamp as a source of ultraviolet light, 93-100% of 1,2,3,4,6,7,8-HpCDF degraded in 60 min in rapeseed oil, extra virgin olive oil and olive oil. Less degradation occurred in palm oil (59%), toluene (39%) and hexane (20%). The better degradation in vegetable oils in comparison with organic solvents was attributed to the photooxidation of lipids producing hydrogen for PCDD/F dechlorination. In addition to the hydrogen donor capacity, permeability of ultraviolet light was involved in the differences between vegetable oils. {alpha}-Tocopherol and chlorophyll did not influence the performance of oil at concentrations normally present in vegetable oils, whereas {beta}-carotene had an inhibitory effect on the degradation of 1,2,3,4,6,7,8-HpCDF. Up to 28% of the degradation products of 1,2,3,4,6,7,8-HpCDF were formed via the dechlorination pathway. Products included both toxic (2,3,7,8-chlorinated) and non-toxic PCDD/Fs, the toxic PCDD/Fs being more stable. Irradiation of 1,2,3,4,6,7,8-HpCDD yielded only non-toxic dechlorination products. Polychlorinated hydroxybiphenyls (OH-PCBs), polychlorinated dihydroxybiphenyls (DOH-PCBs) and polychlorinated hydroxydiphenylethers (OH-PCDEs) containing one to seven chlorine atoms were not detected in irradiated HpCDF/HpCDD samples.

Salt marsh recovery from a crude oil spill: Vegetation, oil weathering, and response

International Nuclear Information System (INIS)

Hoff, R.Z.; Shigenaka, G.; Henry, C.B. Jr.

1993-01-01

When a spill of Prudhoe Bay crude oil covered a fringing Salicornia virginica marsh in Fidalgo Bay, Washington (northern Puget Sound) in February 1991, response personnel used several low-impact techniques to remove oil from the marsh, and minimized access by cleanup workers. Following the response, a monitoring program was established to track marsh recovery, and to document the effectiveness of the response techniques used and their impacts on the marsh. Through monthly sampling over a 16-month period, vegetative growth was monitored and chemical degradation of remaining oil was tracked. Sampling was conducted along transects located in four areas affected in different ways by the spill, including an oiled, trampled section; an oiled, vacuumed section; and an oiled, washed, and vacuumed section. In addition, a control transect was established in an unoiled adjacent marsh. The study included both biological and chemical components. Biological measurements included percent cover of live vegetation (sampled monthly) and below-ground plant biomass (sampled at the beginning of each growing season in April 1991 and April 1992). Sediment samples included surface sediment (monthly) and core samples collected at the beginning and end of the growing seasons. Sediment samples were analyzed using gas chromatography/mass spectroscopy, and indicator compounds were tracked to determine rates of oil degradation. Results from 16 months of post-spill monitoring show that foot trampling was most detrimental to marsh plants, while washing with vacuuming removed the most oil and minimized adverse impacts to vegetation. Dense clay substrate helped prevent oil from penetrating the sediment, thus minimizing acute toxic effects from oil exposure to marsh plant rootstock. By the second growing season post-spill, Salicornia and other marsh plants were growing in all areas except one heavily oiled patch

Lipid Peroxidation in Rat Liver using Different Vegetable Oils

International Nuclear Information System (INIS)

Eqbal Dauqan; Aminah Abdullah; Halimah Abdullah Sani

2013-01-01

The objective of the study was to evaluate the effect of different vegetable oils (Red Palm Olien (RPO), Palm Olein (PO), Corn Oil (CO) and Coconut Oil on lipid peroxidation of rat liver. One hundred and thirty two Sprague Dawley male rats were randomly divided into two groups. The first group contains seventy two rats were divided into twelve groups of 6 rats per group and were treated with different concentrations of RPO (5 %, 10 % and 15 %) for 2, 4 and 8 weeks. The second group contains sixty male rats were randomly divided into ten groups of 6 rats per group and were treated with 15 % of RPO, PO, CO and COC for 4 and 8 weeks. The results shows that after 8 weeks of treatment the malonaldehyde (MDA) value in RPO group was significantly lower (P≤0.05) than control or vegetable oils studied. These experiments suggested that red palm olein antioxidants present in rat diets may better attenuate peroxyl radical than other vegetable oil studied. (author)

Replacement of milk fat by mixed vegetable oils in manufacturing soft cheese treated by gamma irradiation

International Nuclear Information System (INIS)

Afifi, E.A.; Anwar, M.M.

2007-01-01

This investigation aimed to study the possibility of substituting milk fat by using blended vegetable oils in manufacturing soft cheese with low salt content, in addition, lo utilize gamma irradiation to prolong the shelf-life of the new manufactured product. Therefore, one hundred (lOOKg) from fresh buffaloes milk containing 5 % milk fal and 3 % salt were divided into tow parts , the first part was used for manufacturing control soft cheese sample (containing milk fat ), while the second part was skimmed, blended with blended vegetable oils and homogenized. The skim homogenized milk containing 5% mixed vegetable oils used for manufacturing soft cheese ( new product filled ). The obtained soft cheese was subjected to 1, 2 and 3 kGy y-irradiation, and stored at refrigerator temperature. During cold storage, the sensory, microbial and chemical properties of control soft cheese and treated one were evaluated. The obtained results indicated that the replacement of milk fat by mixed vegetable oils in the manufacturing soft cheese had no effect on chemical composition and sensory properties except white color and slight oily flavor which have been noticed in treated filled cheese. In addition, irradiation dose of 3 kGy prolonged the shelf-life of treated filled cheese to 42 days compared to 18 days for control sample and scqueiitly, the new product high percentage of iinsaluraled fatly acid and no cholesterol compared with cheese made from natural milk and can be recommended as a healthy food especially for those who need to low or free cholesterol foods

Production of Biodiesel from Locally Available Spent Vegetable Oils

Directory of Open Access Journals (Sweden)

Mohamed Mostafa Al Naggar

2017-06-01

Full Text Available The depletion of fossil fuels prompted considerable research to find alternative fuels. Due its environmental benefits and renewable nature the production of biodiesel has acquired increasing importance with a view to optimizing the production procedure and the sources of feedstock. Millions of liters of waste frying oil are produced from local restaurants and houses every year, most are discarded into sewage systems causing damage to the networks.  This study is intended to consider aspects related to the feasibility of the production of biodiesel from waste frying oils which will solve the problem of waste frying oil pollution and reduce the cost of biodiesel production.This research studies the conversion of locally available spent vegetable oils of different origins and with different chemical compositions into an environmentally friendly fuel. The biodiesel production requirements by base catalyzed trans-esterification process for the different feed stocks are determined according to the measured physical properties. The quality of the produced biodiesel is compared to petro diesel in terms of established standard specifications.

Eco-Friendly Multipurpose Lubricating Greases from Vegetable Residual Oils

Directory of Open Access Journals (Sweden)

Ponnekanti Nagendramma

2015-10-01

Full Text Available Environmentally friendly multipurpose grease formulation has been synthesized by using Jatropha vegetable residual oil with lithium soap and multifunctional additive. The thus obtained formulation was evaluated for its tribological performance on a four-ball tribo-tester. The anti-friction and anti-wear performance characteristics were evaluated using standard test methods. The biodegradability and toxicity of the base oil was assessed. The results indicate that the synthesized residual oil grease formulation shows superior tribological performance when compared to the commercial grease. On the basis of physico-chemical characterization and tribological performance the vegetable residual oil was found to have good potential for use as biodegradable multipurpose lubricating grease. In addition, the base oils are biodegradable and non toxic.

Production and characterization of a functional Iranian white brined cheese by replacement of dairy fat with vegetable oils.

Science.gov (United States)

Achachlouei, B Fathi; Hesari, J; Damirchi, S Azadmard; Peighambardoust, Sh; Esmaiili, M; Alijani, S

2013-10-01

Full-fat cheese usually contains high amounts of saturated fatty acids and cholesterol, which may have negative health effects. In this study, full-fat white brined cheese, as a control sample, and experimental cheeses with olive and canola oils (T1, white brined cheese containing 50% canola oil, T2, white brined cheese containing 50% olive oil, T3, white brined cheese containing 100% canola oil and T4, white brined cheese containing 100% olive oil) were prepared from bovine milk. Physicochemical properties, lipolysis, proteolysis patterns and sensorial properties in the prepared samples were determined during 80 days of storage at 20-day intervals. Cheese incorporating vegetable oils showed lower amounts of saturated fatty acids and higher amounts of unsaturated fatty acids compared with the full-fat cheese (control) samples. Moisture, pH, lipolysis value, as assessed by the acid-degree value, and proteolysis values (pH 4.6 SN/TN% and NPN/TN%) significantly (p titrable acidity decreased during 40 days of ripening but then increased slightly. Sensory properties of white brined cheese incorporating with vegetable oils were different from those of full-fat cheese samples. White brined cheese containing olive and canola oils (100% fat substitution) received better sensory scores compared to other samples. The results showed that it is possible to replace dairy fat with olive and canola oils, which can lead to produce a new healthy and functional white brined cheese.

Tensão superficial estática de soluções aquosas com óleos minerais e vegetais utilizados na agricultura Surface tension of mineral oils and vegetable oils

Directory of Open Access Journals (Sweden)

Cristina G. de Mendonça

2007-01-01

improve any characteristics of the spray solution. The surface tension was evaluated in emulsion contend: mineral oils (Assist, Attach, Dytrol, Iharol, Mineral Oil, Spinner, Sunspray-E e Triona and vegetable oils (Agrex'oil Vegetal, Crop Oil, Natur'l Óleo, Óleo Vegetal Nortox e Veget Oil. For each product were evaluated eleven concentrations. This property of the mineral oils and vegetable oils were evaluated with the weight of drops formed in the extremity of a burette. The data were adjusted to the Mitscherlich's Model. The mineral oils Assist, Dytrol, Iharol and Mineral Oil presented the smallest minimum surface tension, respectively, 29.255; 28.442; 26.097 and 28.584 mN m-1. The vegetal oils that presented the smallest values of minimum superficial tension were: Agrex' oil Vegetal (27.716 mN m-1, Natur'l Óleo (28.216 mN m-1, Veget Oil (27.308 mN m-1 and Crop Oil (29.964 mN m-1.

Optimization of Refining Craft for Vegetable Insulating Oil

Science.gov (United States)

Zhou, Zhu-Jun; Hu, Ting; Cheng, Lin; Tian, Kai; Wang, Xuan; Yang, Jun; Kong, Hai-Yang; Fang, Fu-Xin; Qian, Hang; Fu, Guang-Pan

2016-05-01

Vegetable insulating oil because of its environmental friendliness are considered as ideal material instead of mineral oil used for the insulation and the cooling of the transformer. The main steps of traditional refining process included alkali refining, bleaching and distillation. This kind of refining process used in small doses of insulating oil refining can get satisfactory effect, but can't be applied to the large capacity reaction kettle. This paper using rapeseed oil as crude oil, and the refining process has been optimized for large capacity reaction kettle. The optimized refining process increases the acid degumming process. The alkali compound adds the sodium silicate composition in the alkali refining process, and the ratio of each component is optimized. Add the amount of activated clay and activated carbon according to 10:1 proportion in the de-colorization process, which can effectively reduce the oil acid value and dielectric loss. Using vacuum pumping gas instead of distillation process can further reduce the acid value. Compared some part of the performance parameters of refined oil products with mineral insulating oil, the dielectric loss of vegetable insulating oil is still high and some measures are needed to take to further optimize in the future.

The effect of partial substitution of pork back fat with vegetable oils and walnuts on chemical composition, texture profile and sensorial properties of meatloaf

Directory of Open Access Journals (Sweden)

Gabriel Dănuţ MOCANU

2015-08-01

Full Text Available The present study investigates the effects of the partial substitution of the pork back fat with different vegetable oils (sea buckthorn, walnut and sunflower and walnuts on the chemical composition, texture profile and sensory characteristics of meatloaves. The dry matter and ash content of meatloaf with vegetable oils and walnuts were higher than the control sample (P < 0.05. The cooking loss, energy values and lipid oxidation for the samples with walnuts and vegetable oils were lower than the control sample. The meatloaf sample containing walnuts and sea buckthorn oil had the highest total antioxidant capacity. The partial substitution of pork back fat showed a positive effect on textural and sensorial characteristics. Results reveal that the incorporation of vegetable oils and walnuts has successfully reduced the animal fat content in the finite products while improving the quality characteristics.

Vegetable oils as diesel fuel

International Nuclear Information System (INIS)

Fedeli, E.; Girelli, A.

2001-01-01

During the seventies, one of the recurring fuels crisis gave rise to research on alternative sources and among them to the idea of utilizing vegetable oils. The research work made clear that the oils cannot be utilized as such but they must be transformed in simple esters, eliminating the problems arising from the presence of the glycerine. The Experiment Stations of the Industry, Commerce and Handicraft Department of the Italian Government, by request of the last one, in the '70/'80 has done a successful experimentation that is presented in the paper [it

Polymercaptanized soybean oil – properties and tribological characterization

Science.gov (United States)

Polymercaptanized vegetable oils are produced in industrial scale by the addition of hydrogen sulfide across double bonds or epoxides of vegetable oils, in the presence of UV-light. To date, soybean oil, epoxidized soybean oil, and castor oil has been mercaptanized using such a procedure. Depending ...

Highly efficient procedure for the transesterification of vegetable oil

Energy Technology Data Exchange (ETDEWEB)

Liang, Xuezheng; Gao, Shan; He, Mingyuan [Shanghai Key Laboratory of Green Chemistry and Chemical Process, Department of Chemistry, East China Normal University, Shanghai 200062 (China); Yang, Jianguo [Shanghai Key Laboratory of Green Chemistry and Chemical Process, Department of Chemistry, East China Normal University, Shanghai 200062 (China); Energy Institute, Department of Materials Science and Engineering, Pennsylvania State University, University Park, PA 16802 (United States)

2009-10-15

The highly efficient procedure has been developed for the synthesis of biodiesel from vegetable oil and methanol. The KF/MgO has been selected as the most efficient catalyst for the reactions with the yield of 99.3%. Operational simplicity, without need of the purification of raw vegetable oil, low cost of the catalyst used, high activities, no saponification and reusability are the key features of this methodology. (author)

Effect of vegetable oils on fatty acid composition and cholesterol content of chicken frankfurters

Science.gov (United States)

Belichovska, D.; Pejkovski, Z.; Belichovska, K.; Uzunoska, Z.; Silovska-Nikolova, A.

2017-09-01

To study the effect of pork adipose tissue substitution with vegetable oils in chicken frankfurters, six frankfurter formulations were produced: control; with pork backfat; with olive oil; with rapeseed oil; with sunflower oil; with palm oil, and; with a mixture of 12% rapeseed oil and 8% palm oil. Fatty acid composition and cholesterol content and some oxides thereof were determined in the final products. The use of vegetable oils resulted in improvement of the fatty acid composition and nutritional of frankfurters. Frankfurters with vegetable oils contained significantly less cholesterol and some of its oxides, compared to the frankfurters with pork fat. The formulation with palm oil had the least favourable fatty acid composition. The use of 12% rapeseed oil improved the ratio of fatty acids in frankfurters with a mixture of rapeseed and palm oils. Complete pork fat replacement with vegetable oils in chicken frankfurter production is technologically possible. The mixture of 12% rapeseed oil and 8% palm oil is a good alternative to pork fat from health aspects. Further research is needed to find the most appropriate mixture of vegetable oils, which will produce frankfurters with good sensory characteristics, a more desirable fatty acid ratio and high nutritional value.

Production of Biodiesel from Waste Vegetable Oil via KM Micromixer

Directory of Open Access Journals (Sweden)

M. F. Elkady

2015-01-01

Full Text Available The production of biodiesel from waste vegetable oils through its pretreatment followed by transesterification process in presence of methanol was investigated using a KM micromixer reactor. The parameters affecting biodiesel production process such as alcohol to oil molar ratio, catalyst concentration, the presence of tetrahydrofuran (THF as a cosolvent, and the volumetric flow rates of inlet fluids were optimized. The properties of the produced biodiesel were compared with its parent waste oil through different characterization techniques. The presence of methyl ester groups at the produced biodiesel was confirmed using both the gas chromatography-mass spectrometry (GC-MS and the infrared spectroscopy (FT-IR. Moreover, the thermal analysis of the produced biodiesel and the comparable waste oil indicated that the product after the transesterification process began to vaporize at 120°C which makes it lighter than its parent oil which started to vaporize at around 300°C. The maximum biodiesel production yield of 97% was recorded using 12 : 1 methanol to oil molar ratio in presence of both 1% NaOH and THF/methanol volume ratio 0.3 at 60 mL/h flow rate.

Oilseeds and vegetable oils in asia: a world of diversity

Directory of Open Access Journals (Sweden)

Mittaine Jean-François

2016-11-01

Full Text Available Out of the two dozen countries that constitute what is generally called “Asia”, some are the largest in the world while others are islands with smaller populations. When looking at oilseeds and vegetable oils in the region, one is faced with the same huge diversity which makes it complex to analyze, all the more that statistics are not easily available for many countries. Aside from the large differences in size, the region covers a wide spectrum of diversified climate environments. Asia is also mainly characterized by its huge population which has become largely urban, a key factor leading to the impressive growth of vegetable oil demand in the past 30 years. At an verage of 23.2 kg/year, Asian per capita consumption of oils and fats still remains slightly below the world average of 28.3 kg/capita/year. Therefore, although 53% of the world population is located in Asia, only 45% of world oils and fats is consumed in the region. As detailed in the paper, the world of Asian oilseeds and vegetable oils is highly concentrated on soybeans and palm oil. In spite of a large domestic production in China (12.3 MnT, soybeans are imported in huge quantities, mostly by China (78 MnT, 84% of the region’s imports where more than 28% of world soybeans production is being crushed. Palm oil, the second large commodity consumed in the region, is mainly produced within the region, mostly in Indonesia and Malaysia. So where is the “world of diversity”? Hidden behind those two dominant commodities, practically all of the ten oilseeds constituting the core of the world production are grown in significant quantities in the region while, for vegetable oils, all those of significant importance are produced within the region with the exception of olive oil. The main question that should be kept in mind when reviewing this large regional demand is under what condition will future vegetable oil production be able to meet the expected rise of per capita oils and

A comparative analysis of physical and chemical properties of Jatropha Curcas. L, Calophyllum Inophyllum. L and Sterculia Feotida. L oil

Energy Technology Data Exchange (ETDEWEB)

Silitonga, A.S. [Department of Mechanical Engineering, Medan State Polytechnic (Indonesia)], email: ardinsu@yahoo.co.id, email: a_atabani2@msn.com; Atabani, A.E. [Department of Mechanical Engineering, University of Khartoum (Sudan); Mahlia, T.M.I. [Department of Mechanical Engineering, Syiah Kuala University, (Indonesia); Masjuki, H.H.; Badruddin, I.A. [Department of Mechanical Engineering, University of Malaya (Malaysia)

2011-07-01

Production of bio-diesel converted from edible oil has raised the issue of competition for resources between food production and fuel production, as well as other questions of environmental impact. It has been established that producing bio-diesel from non-edible vegetable oils was one of the effective ways to resolve these issues. Jatropha curcas L., Calophyllum inophyllum L., and Sterculia foetida L. are all non-edible oils and all can be potential sources for future energy supply. The purpose of this paper is to reveal the results of a comparative analysis of the physical and chemical properties of Jatropha curcas L., Calophyllum inophyllum L., and Sterculia foetida L. oils. Physical and chemical properties of these vegetable oils, such as density, iodine value, free fatty acid, etc. were investigated and measured. These properties were then compared with those of other non-edible vegetable oils in terms of potential. This paper finds that the results of analysis indicate that there is high potential for using Jatropha curcas L., Calophyllum inophyllum L., and Sterculia foetida L. crude oil as an alternative fuel.

Production of vegetal oil for energetic purposes; Producao de oleo vegetal com fins energeticos a partir de oleoginosas perenes

Energy Technology Data Exchange (ETDEWEB)

Andrade Pinto, R. de [Companhia Paranaense de Energia (COPEL), Curitiba, PQ (Brazil)

1987-12-31

The technology to obtain vegetable oil from trans esterification is already dominated. However, the oil grain`s cultures of annual cycle (soy-beans, peanuts, sunflowers) demand fertile and plain lands, which actually ought to be destined for food production, The utilization of slope wise areas, which are often destroyed by means of burning, for the reforestation with perennial oily trees which will be subject for further experimental researches, is studied. Particularly, the studies involves the cultivation of avocado`s varieties, which present pulps with a high oil concentration, in regions of temperate climates. It also involves an analysis of the high productivity and various difficulties to be surpassed, since the development of a simple procedure for thr oils and by-products extraction (in rural properties), until genetic developments of new avocado`s kinds, in order to achieve a better adaptation to the regions climate and to contain a higher oil concentration. 7 refs., 1 tab.

Using vegetable oils and animal fats in Diesel Engines: chemical analyses and engine texts

International Nuclear Information System (INIS)

Marmino, I.; Verhelst, S.; Sierens, R.

2008-01-01

In this work, some vegetable oils (rapeseed oil, palm oil) and animal fat were tested in a Diesel engine at a range of engine spreads and torque settings, after preheating at 70 0 C. Engine performance, fuel consumption and NOx, unburnt hydrocarbons and soot emissions have been recorded. The results have been compared to those obtained with diesel fuel in the same test conditions. The oils and fats were also analyzed for their physical and chemical properties (viscosity, composition, unsaturation, heating value). NOx emissions were found to be lower for the oils than for the diesel fuel. This, combined with higher HC emissions, can probably be explained through less effective atomization due to the higher viscosity of the oils and fat. On the other hand, soot emissions were found to decrease. [it

Analysis of physical characteristics of vegetable oils

Energy Technology Data Exchange (ETDEWEB)

Piamba Tulcan, Oscar Edwin [Universidade Nacional da Colombia (UNAL), Bogota (Colombia). Fac. de Ingenieria; Universidade Federal Fluminense (PGMEC/UFF), Niteroi, RJ (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica], E-mail: oepiambat@unal.edu.co; Andrade, Danielle Oliveira de; Andrade, Ednilton Tavares de [Universidade Federal Fluminense (TER/UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Agricola e do Meio Ambiente; Pereira, Roberto Guimaraes [Universidade Federal Fluminense (TER/UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Mecanica

2008-07-01

Different vegetable oils were characterized using standardized methods. The evaluated characteristics were density, viscosity, flow point, cloud point and corrosion. The obtained data was tabulated and compared with average composition values of oils in percentage of fatty acids and iodine number for each oil. In this analysis it is shown that viscosity decreases with the increase of the iodine number, and density decrease. The cloud and flow point have greater relation with the presence of saturated or highly unsaturated fatty acids, respectively. The index of corrosion is greater when oil saturation or its iodine number are increased. (author)

Analysis of Brand Preference for Vegetable Oil in Abia State, Nigeria ...

African Journals Online (AJOL)

This study examined the consumer brand preference for vegetable oil in Abia State. It specifically focused on the determining factors that influenced consumer preference between branded and unbranded vegetable oil. This study adopted multistage sampling technique in the selection of a total sample of 150 respondents.

SOLID BIOFUEL UTILIZATION IN VEGETABLE OIL PRODUCTION

Directory of Open Access Journals (Sweden)

Slusarenko V.

2016-08-01

Full Text Available The paper deals with questions of creating at JSC “Alimentarmash "in the last 20 years the technological equipment for the production of vegetable oils from oilseeds: from the press for the final spin to mini oilfactory, using as an energy source for heating the liquid coolant (Thermal oil "Arian" of solid biofuels - husk of sunflower seeds.

Straight vegetable oils usage in a compression ignition engine - A review

Energy Technology Data Exchange (ETDEWEB)

Misra, R.D.; Murthy, M.S. [Mechanical Engineering Department, National Institute of Technology, Silchar 788010, Assam (India)

2010-12-15

The ever increasing fossil fuel usage and cost, environmental concern has forced the world to look for alternatives. Straight vegetable oils in compression ignition engine are a ready solution available, however, with certain limitations and with some advantages as reported by many researchers. A comprehensive and critical review is presented specifically pertaining to straight vegetable oils usage in diesel engine. A detailed record of historical events described. Research carried out specifically under Indian conditions and international research work on the usage of straight vegetable oils in the diesel engine is separately reviewed. Many researchers have reported that straight vegetable oils in small percentage blends with diesel when used lower capacity diesel engines have shown great promise with regards to the thermal performance as well exhaust emissions. This has been explained in detail. Finally based on the review of international as well as Indian research a SWOT analysis is carried out. The review concludes that there is still scope for research in this area. (author)

Palm Oil Consumption Increases LDL Cholesterol Compared with Vegetable Oils Low in Saturated Fat in a Meta-Analysis of Clinical Trials.

Science.gov (United States)

Sun, Ye; Neelakantan, Nithya; Wu, Yi; Lote-Oke, Rashmi; Pan, An; van Dam, Rob M

2015-07-01

Palm oil contains a high amount of saturated fat compared with most other vegetable oils, but studies have reported inconsistent effects of palm oil on blood lipids. We systematically reviewed the effect of palm oil consumption on blood lipids compared with other cooking oils using data from clinical trials. We searched PubMed and the Cochrane Library for trials of at least 2 wk duration that compared the effects of palm oil consumption with any of the predefined comparison oils: vegetable oils low in saturated fat, trans fat-containing partially hydrogenated vegetable oils, and animal fats. Data were pooled by using random-effects meta-analysis. Palm oil significantly increased LDL cholesterol by 0.24 mmol/L (95% CI: 0.13, 0.35 mmol/L; I(2) = 83.2%) compared with vegetable oils low in saturated fat. This effect was observed in randomized trials (0.31 mmol/L; 95% CI: 0.20, 0.42 mmol/L) but not in nonrandomized trials (0.03 mmol/L; 95% CI: -0.15, 0.20 mmol/L; P-difference = 0.02). Among randomized trials, only modest heterogeneity in study results remained after considering the test oil dose and the comparison oil type (I(2) = 27.5%). Palm oil increased HDL cholesterol by 0.02 mmol/L (95% CI: 0.01, 0.04 mmol/L; I(2) = 49.8%) compared with vegetable oils low in saturated fat and by 0.09 mmol/L (95% CI: 0.06, 0.11 mmol/L; I(2) = 47.8%) compared with trans fat-containing oils. Palm oil consumption results in higher LDL cholesterol than do vegetable oils low in saturated fat and higher HDL cholesterol than do trans fat-containing oils in humans. The effects of palm oil on blood lipids are as expected on the basis of its high saturated fat content, which supports the reduction in palm oil use by replacement with vegetable oils low in saturated and trans fat. This systematic review was registered with the PROSPERO registry at http://www.crd.york.ac.uk/PROSPERO/display_record.asp?ID=CRD42012002601#.VU3wvSGeDRZ as CRD42012002601. © 2015 American Society for Nutrition.

Assessing food allergy risks from residual peanut protein in highly refined vegetable oil

NARCIS (Netherlands)

Blom, W.M.; Kruizinga, A.G.; Rubingh, C.M.; Remington, B.C.; Crevel, R.W.R.; Houben, G.F.

2017-01-01

Refined vegetable oils including refined peanut oil are widely used in foods. Due to shared production processes, refined non-peanut vegetable oils can contain residual peanut proteins. We estimated the predicted number of allergic reactions to residual peanut proteins using probabilistic risk

Vegetable fats and oils as functional ingredients in meat products

Directory of Open Access Journals (Sweden)

Alfonso Totosaus

2011-12-01

Full Text Available Sausages are a widely consumed food in México, and due to their low fat content (ca. 10% they can be employed to enrich diet by including functional or nutraceutic ingredients as vegetable fats and oils. The replace or incorporation of vegetable fats or oils in cooked sausages is a way to improve their nutritional profile to offer functional meat products.

Tribological Performance of Hydrogenated Amorphous Carbon (a-C: H DLC Coating when Lubricated with Biodegradable Vegetal Canola Oil

Directory of Open Access Journals (Sweden)

H.M. Mobarak

2014-06-01

Full Text Available Increasing environmental awareness and demands for lowering energy consumptions are strong driving forces behind the development of the vehicles of tomorrow. Without the advances of lubricant chemistry and adequate lubricant formulation, expansion of modern engines would not have been possible. Considering environmental awareness factors as compared to mineral oils, vegetal oil based biolubricants are renewable, biodegradable, non-toxic and have a least amount of greenhouse gases. Furthermore, improvement in engine performance and transmission components, which were impossible to achieve by applying only lubricants design, is now possible through diamond like carbon (DLC coatings. DLC coatings exhibit brilliant tribological properties, such as good wear resistance and low friction. In this regard, tribological performance of a-C: H DLC coating when lubricated with Canola vegetal oil has been investigated by the help of a ball-on-flat geometry. Experimental results demonstrated that the a-C: H DLC coating exhibited better performance with Canola oil in terms of friction and wear as compared to the uncoated materials. Large amount of polar components in the Canola oil significantly improved the tribological properties of the a-C:H coating. Thus, usage of a-C: H DLC coating with Canola oil in the long run may have a positive impact on engine life.

Optimization of biodiesel production process using recycled vegetable oil

Science.gov (United States)

Lugo, Yarely

Petro diesel toxic emissions and its limited resources have created an interest for the development of new energy resources, such as biodiesel. Biodiesel is traditionally produced by a transesterification reaction between vegetable oil and an alcohol in the presence of a catalyst. However, this process is slow and expensive due to the high cost of raw materials. Low costs feedstock oils such as recycled and animal fats are available but they cannot be transesterified with alkaline catalysts due to high content of free fatty acids, which can lead to undesirable reactions such as saponification. In this study, we reduce free fatty acids content by using an acid pre-treatment. We compare sulfuric acid, hydrochloric acid and ptoluenesulfonic acid (PTSA) to pre-treat recycled vegetable oil. PTSA removes water after 60 minutes of treatment at room temperature or within 15 minutes at 50°C. The pretreatment was followed by a transesterification reaction using alkaline catalyst. To minimize costs and accelerate reaction, the pretreatment and transesterification reaction of recycle vegetable oil was conducted at atmospheric pressure in a microwave oven. Biodiesel was characterized using a GC-MS method.

Catalytic cracking of vegetable oil with metal oxides for biofuel production

International Nuclear Information System (INIS)

Yigezu, Zerihun Demrew; Muthukumar, Karuppan

2014-01-01

Highlights: • Biofuel was synthesized from vegetable oil by catalytic cracking. • Performance of six different metal catalysts was studied. • Influence of temperature and reaction time on the process was evaluated. • Methyl and ethyl esters are the major components of the biofuel synthesized. - Abstract: This study presents the utilization of metal oxides for the biofuel production from vegetable oil. The physical and chemical properties of the diesel-like products obtained, and the influence of reaction variables on the product distribution were investigated. Six different metal oxides (Co 3 O 4 , KOH, MoO 3 , NiO, V 2 O 5 , and ZnO) were employed as catalysts and the results indicated that the metal oxides are suitable for catalyzing the conversion of oil into organic liquid products (OLPs). The maximum conversion (87.6%) was obtained with V 2 O 5 at 320 °C in 40 min whereas a minimum conversion (55.1%) was obtained with MoO 3 at 390 °C in 30 min. The physical characteristics of the product obtained (density, specific gravity, higher heat value, flash point and kinematic viscosity), were in line with ASTM D6751 (B100) standards. The hydrocarbons majorly present in the product were found to be methyl and ethyl esters. Furthermore, OLPs obtained were distilled and separated into four components. The amount of light hydrocarbons, gasoline, kerosene and heavy oil like components obtained were 18.73%, 33.62%, 24.91% and 90.93%, respectively

Biodiesel production from vegetable oil and waste animal fats in a pilot plant.

Science.gov (United States)

Alptekin, Ertan; Canakci, Mustafa; Sanli, Huseyin

2014-11-01

In this study, corn oil as vegetable oil, chicken fat and fleshing oil as animal fats were used to produce methyl ester in a biodiesel pilot plant. The FFA level of the corn oil was below 1% while those of animal fats were too high to produce biodiesel via base catalyst. Therefore, it was needed to perform pretreatment reaction for the animal fats. For this aim, sulfuric acid was used as catalyst and methanol was used as alcohol in the pretreatment reactions. After reducing the FFA level of the animal fats to less than 1%, the transesterification reaction was completed with alkaline catalyst. Due to low FFA content of corn oil, it was directly subjected to transesterification. Potassium hydroxide was used as catalyst and methanol was used as alcohol for transesterification reactions. The fuel properties of methyl esters produced in the biodiesel pilot plant were characterized and compared to EN 14214 and ASTM D6751 biodiesel standards. According to the results, ester yield values of animal fat methyl esters were slightly lower than that of the corn oil methyl ester (COME). The production cost of COME was higher than those of animal fat methyl esters due to being high cost biodiesel feedstock. The fuel properties of produced methyl esters were close to each other. Especially, the sulfur content and cold flow properties of the COME were lower than those of animal fat methyl esters. The measured fuel properties of all produced methyl esters met ASTM D6751 (S500) biodiesel fuel standards. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of Presence and Concentration of Plasticizers, Vegetable Oils, and Surfactants on the Properties of Sodium-Alginate-Based Edible Coatings

Science.gov (United States)

Schott, Michael; Müller, Kajetan

2018-01-01

Achieving high quality of a coated food product is mostly dependent on the characteristics of the food material to be coated, the properties of the components in the coating solution, and the obtained coating material. In the present study, usability and effectiveness of various components as well as their concentrations were assessed to produce an effective coating material. For this purpose, different concentrations of gelling agent (sodium alginate 0–3.5%, w/w), plasticizers (glycerol and sorbitol (0–20%, w/w), surfactants (tween 40, tween 80, span 60, span 80, lecithin (0–5%, w/w), and vegetable oils (sunflower oil, olive oil, rapeseed oil (0–5%, w/w) were used to prepare edible coating solutions. Formulations were built gradually, and characteristics of coatings were evaluated by analyzing surface tension values and its polar and dispersive components, emulsion droplet size, and optical appearance in microscopic scale. The results obtained showed that 1.25% sodium alginate, 2% glycerol, 0.2% sunflower oil, 1% span 80, and 0.2% tween 40 or tween 80 can be used in formulation to obtain an effective coating for hydrophobic food surfaces. Three formulations were designed, and their stability (emulsion droplet size, optical characteristics, and creaming index) and wettability tests on strawberry showed that they could be successfully used in coating applications. PMID:29509669

Effect of Presence and Concentration of Plasticizers, Vegetable Oils, and Surfactants on the Properties of Sodium-Alginate-Based Edible Coatings

Directory of Open Access Journals (Sweden)

Tugce Senturk Parreidt

2018-03-01

Full Text Available Achieving high quality of a coated food product is mostly dependent on the characteristics of the food material to be coated, the properties of the components in the coating solution, and the obtained coating material. In the present study, usability and effectiveness of various components as well as their concentrations were assessed to produce an effective coating material. For this purpose, different concentrations of gelling agent (sodium alginate 0–3.5%, w/w, plasticizers (glycerol and sorbitol (0–20%, w/w, surfactants (tween 40, tween 80, span 60, span 80, lecithin (0–5%, w/w, and vegetable oils (sunflower oil, olive oil, rapeseed oil (0–5%, w/w were used to prepare edible coating solutions. Formulations were built gradually, and characteristics of coatings were evaluated by analyzing surface tension values and its polar and dispersive components, emulsion droplet size, and optical appearance in microscopic scale. The results obtained showed that 1.25% sodium alginate, 2% glycerol, 0.2% sunflower oil, 1% span 80, and 0.2% tween 40 or tween 80 can be used in formulation to obtain an effective coating for hydrophobic food surfaces. Three formulations were designed, and their stability (emulsion droplet size, optical characteristics, and creaming index and wettability tests on strawberry showed that they could be successfully used in coating applications.

The effects of heated vegetable oils on blood pressure in rats

Directory of Open Access Journals (Sweden)

Kamsiah Jaarin

2011-01-01

Full Text Available OBJECTIVES: The goal of this study was to determine the possible mechanism that is involved in the blood pressureraising effect of heated vegetable oils. METHODS: Adult male Sprague-Dawley rats were divided into 11 groups; the control group was fed with rat chow, and the other groups were fed with chow that was mixed with 15% weight/weight palm or soy oils, which were either in a fresh form or heated once, twice, five, or ten times. Blood pressures were measured at the baseline and throughout the 24-week study. Plasma nitric oxide levels were assessed prior to treatment and at the end of the study. Following 24 weeks, the rats were sacrificed to investigate their vascular reactivity using the thoracic aorta. RESULTS: Palm and soy oils had no detrimental effects on blood pressure, and they significantly elevated the nitric oxide contents and reduced the contractile responses to phenylephrine. However, trials using palm and soy oils that were repeatedly heated showed an increase in blood pressure, enhanced phenylephrine-induced contractions, reduced acetylcholine- and sodium nitroprusside-induced relaxations relative to the control and rats that were fed fresh vegetable oils. CONCLUSIONS: The blood pressure-raising effect of the heated vegetable cooking oils is associated with increased vascular reactivity and a reduction in nitric oxide levels. The chronic consumption of heated vegetable oils leads to disturbances in endogenous vascular regulatory substances, such as nitric oxide. The thermal oxidation of the cooking oils promotes the generation of free radicals and may play an important contributory role in the pathogenesis of hypertension in rats.

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Directory of Open Access Journals (Sweden)

Li Benkai

2016-08-01

Full Text Available Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL. This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that (1 castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient; (2 palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient; (3 MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil; (4 viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils; (5 although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature; (6 saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and (7 a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force, 87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy

Vegetable Oils Consumption as One of the Leading Cause of Cancer and Heart Disease

OpenAIRE

Somayeh Zaminpira; Sorush Niknamian

2017-01-01

This review takes a deep look at increases in the incidence of cancer and heart disease after the introduction of industrial vegetable oils in the world. Most vegetable oils are highly processed and refined products, which completely lack the essential nutrients. Omega-6 Linoleic acid from vegetable oils increases oxidative stress in the body of humans, contributing to endothelial dysfunction and heart disease. The consumption of these harmful oils which are high in mega-6 polyunsaturated fat...

Controlling the frying stability of vegetable oils with tocopherols and phytosterols

Science.gov (United States)

Polyunsaturated vegetable oils are usually oxidatively stable for salad oils; however, in high stability applications such as frying, these oils are not resistant to the deteriorative processes of oxidation, hydrolysis and polymerization. To solve this problem in the past, oils were hydrogenated an...

Investigation of activated Al-pillared clay efficiency in vegetable oil purification

Directory of Open Access Journals (Sweden)

Lomić Gizela A.

2004-01-01

Full Text Available This paper represents a contribution to the applicability of natural clays and their derivates as adsorbents in the process of purification of vegetable oil. Investigation of textural properties of raw and purified clay samples reveals that during acid activation and Al-pillaring, BET and micropore surface area increases significantly. However, bleaching capacity of clay and its derivates is not determined by using sample surface area, but rather sample total pore volume. Surface area, especially micropore surface area contributes to removal of smaller molecules. This was confirmed by successful elimination of moisture and volatile materials by samples with an appropriate micropore structure. Used samples of clay and its derivates do not significantly influence acid and peroxide values of raw sunflower oil during its treatment.

Detection of Adulterated Vegetable Oils Containing Waste Cooking Oils Based on the Contents and Ratios of Cholesterol, β-Sitosterol, and Campesterol by Gas Chromatography/Mass Spectrometry.

Science.gov (United States)

Zhao, Haixiang; Wang, Yongli; Xu, Xiuli; Ren, Heling; Li, Li; Xiang, Li; Zhong, Weike

2015-01-01

A simple and accurate authentication method for the detection of adulterated vegetable oils that contain waste cooking oil (WCO) was developed. This method is based on the determination of cholesterol, β-sitosterol, and campesterol in vegetable oils and WCO by GC/MS without any derivatization. A total of 148 samples involving 12 types of vegetable oil and WCO were analyzed. According to the results, the contents and ratios of cholesterol, β-sitosterol, and campesterol were found to be criteria for detecting vegetable oils adulterated with WCO. This method could accurately detect adulterated vegetable oils containing 5% refined WCO. The developed method has been successfully applied to multilaboratory analysis of 81 oil samples. Seventy-five samples were analyzed correctly, and only six adulterated samples could not be detected. This method could not yet be used for detection of vegetable oils adulterated with WCO that are used for frying non-animal foods. It provides a quick method for detecting adulterated edible vegetable oils containing WCO.

Enzymatic transesterification of waste vegetable oil to produce biodiesel.

Science.gov (United States)

Lopresto, C G; Naccarato, S; Albo, L; De Paola, M G; Chakraborty, S; Curcio, S; Calabrò, V

2015-11-01

An experimental study on enzymatic transesterification was performed to produce biodiesel from waste vegetable oils. Lipase from Pseudomonas cepacia was covalently immobilized on a epoxy-acrylic resin support. The immobilized enzyme exhibited high catalytic specific surface and allowed an easy recovery, regeneration and reutilisation of biocatalyst. Waste vegetable oils - such as frying oils, considered not competitive with food applications and wastes to be treated - were used as a source of glycerides. Ethanol was used as a short chain alcohol and was added in three steps with the aim to reduce its inhibitory effect on lipase activity. The effect of biocatalyst/substrate feed mass ratios and the waste oil quality have been investigated in order to estimate the process performances. Biocatalyst recovery and reuse have been also studied with the aim to verify the stability of the biocatalyst for its application in industrial scale. Copyright © 2015 Elsevier Inc. All rights reserved.

Rheology of oleo gels based on sorbitan and glyceryl mono stearates and vegetable oils for lubricating applications

Energy Technology Data Exchange (ETDEWEB)

Sanchez, R.; Franco, J. M.; Delgado, M. A.; Valencia, C.; Gallegos, C.

2011-07-01

Oleo gels based on sorbitan and glyceryl mono stearates and different types of vegetable oils, potentially applicable as biodegradable alternatives to traditional lubricating greases, have been studied. In particular, the rheological behavior, by means of small-amplitude oscillatory shear (SAOS) measurements, and some lubrication performance-related properties (mechanical stability and tribological response) have been evaluated in this work. SAOS response and mechanical stability of these oleo gels are significantly influenced by the type and concentration of the organogelator and the vegetable oil used in the formulations. Glyceryl monostearate (GMS) generally produces stronger gels than sorbitan monostearate (SMS). The use of low-viscosity oils, such as rapeseed and soybean oils, yields gels with significantly higher values of the linear viscoelastic functions than oleo gels prepared with high-viscosity oils, i.e. castor oil. The rheological behavior of SMS-based oleo gels also depends on the cooling rate applied during the gelification process. On the other hand, the oleo gels studied present low values of the friction coefficient obtained in a tribological contact, although only some GMS/castor oil-based oleo gels exhibit a suitable mechanical stability. (Author) 28 refs.

Review of Heterogeneous Catalysts for Catalytically Upgrading Vegetable Oils into Hydrocarbon Biofuels

OpenAIRE

Xianhui Zhao; Lin Wei; Shouyun Cheng; James Julson

2017-01-01

To address the issues of greenhouse gas emissions associated with fossil fuels, vegetable oilseeds, especially non-food oilseeds, are used as an alternative fuel resource. Vegetable oil derived from these oilseeds can be upgraded into hydrocarbon biofuel. Catalytic cracking and hydroprocessing are two of the most promising pathways for converting vegetable oil to hydrocarbon biofuel. Heterogeneous catalysts play a critical role in those processes. The present review summarizes current progres...

Long storage stability of biodiesel from vegetable and used frying oils

Energy Technology Data Exchange (ETDEWEB)

Abderrahim Bouaid; Mercedes Martinez; Jose Aracil [Complutense University, Madrid (Spain). Department of Chemical Engineering

2007-11-15

Biodiesel is defined as the mono-alkyl esters of vegetable oils. Production of biodiesel has grown tremendously in European Union in the last years. Though the commercial prospects for biodiesel have also grown, there remains some concern with respect to its resistance to oxidative degradation during storage. Due to the chemical structure of biodiesel the presence of the double bond in the molecule produce a high level of reactivity with the oxygen, especially when it placed in contact with air. Consequently, storage of biodiesel over extended periods may lead to degradation of fuel properties that can compromise fuel quality. This study used samples of biodiesel prepared by the process of transesterification from different vegetable oils: high oleic sunflower oil (HOSO), high and low erucic Brassica carinata oil (HEBO and LEBO) respectively and used frying oil (UFO). These biodiesels, produced from different sources, were used to determine the effects of long storage under different conditions on oxidation stability. Samples were stored in white (exposed) and amber (not exposed) glass containers at room temperature. The study was conducted for a period of 30-months. At regular intervals, samples were taken to measure the following physicochemical quality parameters: acid value (AV), peroxide value (PV), viscosity {nu}, iodine value (IV) and insoluble impurities (II). Results showed that AV, PV, {nu} and II increased, while IV decreased with increasing storage time of biodiesel samples. However, slight differences were found between biodiesel samples exposed and not exposed to daylight before a storage time of 12 months. But after this period the differences were significant. 22 refs., 5 figs., 3 tabs.

The effect of refining step on the changes in viscosity values of vegetable oils

International Nuclear Information System (INIS)

Ergonul, P.G.

2013-01-01

In this work, the viscosity values of chemically refined vegetable oils (sunflower, corn, soybean and rapeseed) and physically refined vegetable oils (olive and palm) were determined during refining processes. At this point of view, fatty acid compositions and viscosity values of oil samples were determined. The edible vegetable oils presented Newtonian behavior in shear rates at ranges 6.28-20.93 s/sup -1/. It was observed that palm oil is more viscous than the others. During physical refining, the effect of both oil type and refining steps were significantly important, whereas in chemical refining only the effect of oil type was found statistically important (p<0.01). It was observed that correlation among fatty acid compositions and viscosity values of the samples showed differences according to oil type. (author)

Vegetable oil and fat viscosity forecast models based on iodine number and saponification number

International Nuclear Information System (INIS)

Toscano, G.; Riva, G.; Foppa Pedretti, E.; Duca, D.

2012-01-01

Vegetable oil and fats can be considered as an important renewable source for the energy production. There are many applications where these biofuels are used directly in engines. However, the use of pure vegetable oils causes some problems as consequence of its chemical and physical characteristic. Viscosity is one of the most important parameters affecting several physical and mechanical processes of the operation of the engine. The determination of this parameter at different tis important to determine the behavior of the vegetable oil and fats. In this work we investigated the effects of two analytical chemical parameters (iodine number and saponification number) and forecasting models have been proposed. -- Highlights: ► Vegetable oil and fat viscosity is predicted by mathematical model based on saponification number and iodine number. ► Unsaturated vegetable oils with small size molecules of fatty acids have a lower viscosity values. ► The models proposed show an average error lower than 12%

Fuel Continuous Mixer ? an Approach Solution to Use Straight Vegetable Oil for Marine Diesel Engines

OpenAIRE

Đặng Van Uy; Tran The Nam

2018-01-01

The vegetable oil is well known as green fuel for diesel engines due to its low sunphur content and renewable stock. However, there are some problems raising when vegetable oil is used as fuel for diesel engines such as highly effected by cold weather, lower general efficiency, separation in layer if mixed with diesel oil and so on. To overcome that disadvantiges, the authors propose a new idea that to use a continuous fuel mixer to blend vegetable oil with diesel oil to make so called a mixe...

Detection and quantification of adulteration of sesame oils with vegetable oils using gas chromatography and multivariate data analysis.

Science.gov (United States)

Peng, Dan; Bi, Yanlan; Ren, Xiaona; Yang, Guolong; Sun, Shangde; Wang, Xuede

2015-12-01

This study was performed to develop a hierarchical approach for detection and quantification of adulteration of sesame oil with vegetable oils using gas chromatography (GC). At first, a model was constructed to discriminate the difference between authentic sesame oils and adulterated sesame oils using support vector machine (SVM) algorithm. Then, another SVM-based model is developed to identify the type of adulterant in the mixed oil. At last, prediction models for sesame oil were built for each kind of oil using partial least square method. To validate this approach, 746 samples were prepared by mixing authentic sesame oils with five types of vegetable oil. The prediction results show that the detection limit for authentication is as low as 5% in mixing ratio and the root-mean-square errors for prediction range from 1.19% to 4.29%, meaning that this approach is a valuable tool to detect and quantify the adulteration of sesame oil. Copyright © 2015 Elsevier Ltd. All rights reserved.

ZETA POTENTIAL AND COLOR INVESTIGATIONS OF VEGETABLE OIL BASED EMULSIONS AS ECO-FRIENDLY LUBRICANTS

Directory of Open Access Journals (Sweden)

ROMICĂ CREŢU

2017-06-01

Full Text Available In the past 10 years, the need for biodegradable lubricants has been more and more emphasized. The use of vegetable oils as lubricants offers several advantages. The vegetable oils are biodegradable; thus, the environmental pollution is minimal either during or after their use. The aim of this paper is to presents a preliminary study concerning the influence of some preparation conditions on the stability of vegetable oil-in-water (O/W emulsions as eco-friendly lubricants stabilized by nonionic surfactant. In this context, vegetable oil-in-water emulsions characteristics where assessed using microscopically observation and zeta potential. In addition, the color of these emulsions can be evaluated. It can be observed that the emulsions tend to stabilize in time.

Identification of vegetable oil botanical speciation in refined vegetable oil blends using an innovative combination of chromatographic and spectroscopic techniques.

Science.gov (United States)

Osorio, Maria Teresa; Haughey, Simon A; Elliott, Christopher T; Koidis, Anastasios

2015-12-15

European Regulation 1169/2011 requires producers of foods that contain refined vegetable oils to label the oil types. A novel rapid and staged methodology has been developed for the first time to identify common oil species in oil blends. The qualitative method consists of a combination of a Fourier Transform Infrared (FTIR) spectroscopy to profile the oils and fatty acid chromatographic analysis to confirm the composition of the oils when required. Calibration models and specific classification criteria were developed and all data were fused into a simple decision-making system. The single lab validation of the method demonstrated the very good performance (96% correct classification, 100% specificity, 4% false positive rate). Only a small fraction of the samples needed to be confirmed with the majority of oils identified rapidly using only the spectroscopic procedure. The results demonstrate the huge potential of the methodology for a wide range of oil authenticity work. Copyright © 2014 Elsevier Ltd. All rights reserved.

Sustainability aspects of biobased products : comparison of different crops and products from the vegetable oil platform

NARCIS (Netherlands)

Meesters, K.P.H.; Corré, W.J.; Conijn, J.G.; Patel, M.K.; Bos, H.L.

2012-01-01

This study focusses on the production of vegetable oil based products. A limited number of aspacts of the sustainability of the full chain (from agriculture to product at the factory gate) was evaluated. Three different vegetable oils were taken into account: palm oil, soy oil and rapeseed oil. Also

Genotoxicity of diesel engine emissions during combustion of vegetable oils, mineral oil, and their blends; Gentoxizitaet von Dieselmotoremissionen bei Verbrennung von Pflanzenoelen, Mineraloeldiesel und deren Mischkraftstoffen

Energy Technology Data Exchange (ETDEWEB)

Buenger, Joern

2013-07-09

High particle emissions and strong mutagenic effects were observed after combustion of vegetable oil in diesel engines. This study tested the hypothesis that these results are affected by the amount of unsaturated or polyunsaturated fatty acids of vegetable oils and that blends of diesel fuel and vegetable oil are mutagenic. Three different vegetable oils (linseed oil, LO; palm tree oil, PO; rapeseed oil, RO), blends of 20% vegetable oil and 80% diesel fuel (B20) and 50% vegetable oil and 50% diesel fuel (B50) as well as common diesel fuel (DF) were combusted in a heavy duty diesel engine. The exhaust was investigated for particle emissions and its mutagenic effect in comparison to emissions of DF. The engine was operated using European Stationary Cycle. Particle mass was determined gravimetrically while mutagenicity was determined using the bacterial reverse mutation assay with tester strains TA98 and TA100. Combustion of LO caused the largest amount of total particulate matter (TPM). In comparison to DF it particularly raised the soluble organic fraction (SOF). RO presented second highest TPM and SOF, followed by PO which was scarcely above DF. B50 revealed the lowest amount of TPM while B20 reached as high as DF. RO revealed the highest number of mutations of the vegetable oils closely followed by LO. PO was less mutagenic, but still induced stronger effects than DF. B50 showed higher mutagenic potential than B20. While TPM and SOF were strongly correlated with the content of polyunsaturated fatty acids in the vegetable oils, mutagenicity had a significant correlation with the amount of total unsaturated fatty acids. Vegetable oil blends seem to be less mutagenic than the pure oils with a shifted maximum compared to blends with biodiesel and DF. This study supports the hypothesis that numbers of double bounds in unsaturated fatty acids of vegetable oils combusted in diesel engines influence the amount of emitted particles and the mutagenicity of the exhaust. And

A Novel Approach for Analyzing Water Diffusion in Mineral and Vegetable Oil-Paper Insulation

Directory of Open Access Journals (Sweden)

Bin Du

2014-04-01

Full Text Available Water diffusion characteristics of mineral and vegetable oil-paper insulation systems are important for insulation condition evaluation of oil-filled transformers. In this paper, we describe a novel application method of in situ attenuated total reflection Fourier transform infrared (ATR-FTIR approach for analyzing the diffusion process of water molecules in oil-immersed insulating paper. Two-dimensional correlation was used to analyze the 3700 cm-1 to 3000 cm- 1 hydroxyl peak. The observed results indicated that water molecules form two types of hydroxyl (OH with oil-impregnated paper in the diffusion process are weak and strong hydrogen bonds, respectively. 2D infrared correlation analysis revealed that three OH stretching vibration spectra absorption peaks was existed in hygroscopic vegetable oil-immersed insulating paper. And there are four OH stretching vibration spectra absorption peaks in mineral oil-immersed insulation paper. Furthermore, mineral oil-impregnated paper and vegetable oil-impregnated paper diffusion coefficients were obtained by nonlinear fitting.

Highly effective ionic liquids for biodiesel production from waste vegetable oils

Directory of Open Access Journals (Sweden)

Fathy A. Yassin

2015-03-01

Full Text Available As conventional energy sources deplete, the need for developing alternative energy resources which are environment friendly becomes more imperative. Vegetable oils are attracting increased interest in this purpose. The methanolysis of vegetable oil to produce a fatty acid methyl ester (FAME, i.e., biodiesel fuel was catalyzed by commercial ionic liquid and its chloride modification. The imidazolium chloride ionic liquid was frequently chosen for the synthesis of biodiesel. The dual-functionalized’ ionic liquid is prepared by a direct combination reaction between imidazolium cation and various metal chlorides such as CoCl2, CuCl2, NiCl2, FeCl3 and AlCl3. Imidazolium tetrachloroferrate was proved to be a selective catalyst for the methanolysis reaction at a yield of 97% when used at 1:10, catalyst: oil ratio for 8 h at 55 °C. Operational simplicity, reusability of the used catalyst for 8 times at least, high yields and no saponification are the key features of this methodology. The dynamic viscosity and density of the upgraded vegetable oil decreased from 32.1 cP and 0.9227 g/cm3 to 10.2 cP and 0.9044 g/cm3 respectively, compared to those of the base vegetable oil. The objective of this study was the synthesis and characterization of biodiesel using commercial ionic liquid and its chloride modification. The ionic liquid catalysts were characterized using FTIR, Raman spectroscopy, DSC, TG and UV.

Avocado and olive oil methyl esters

International Nuclear Information System (INIS)

Knothe, Gerhard

2013-01-01

Biodiesel, the mono-alkyl esters of vegetable oils, animal fats or other triacylglycerol-containing materials and an alternative to conventional petroleum-based diesel fuel, has been derived from a variety of feedstocks. Numerous feedstocks have been investigated as potential biodiesel sources, including commodity oils, however, the methyl esters of avocado and olive oil would likely be suitable as biodiesel fuel. In order to expand the database and comprehensive evaluation of the properties of vegetable oil esters, in this work the fuel-related properties of avocado and olive oil methyl esters, which exhibit similar fatty acid profiles including high oleic acid content, are determined. The cetane numbers of avocado oil methyl esters and olive oil methyl esters are relatively high, determined as 59.2 and 62.5, respectively, due to their elevated content of methyl oleate. Other properties are well within the ranges specified in biodiesel standards. The cloud points of both esters are slightly above 0 °C due to their content of saturated esters, especially methyl palmitate. Overall, avocado and olive oil yield methyl esters with fuel properties comparable to methyl esters from other commodity vegetable oils. The 1 H and 13 C NMR spectra of avocado and olive oil methyl esters are reported. -- Highlights: • Methyl esters of avocado and olive oil meet biodiesel fuel standards. • Provides comparison for methyl esters of other vegetable oils with high oleic content. • Discusses and compares present results with prior literature

Vegetable Oil-Based Hyperbranched Thermosetting Polyurethane/Clay Nanocomposites.

Science.gov (United States)

Deka, Harekrishna; Karak, Niranjan

2009-04-25

The highly branched polyurethanes and vegetable oil-based polymer nanocomposites have been showing fruitful advantages across a spectrum of potential field of applications. Mesua ferrea L. seed oil-based hyperbranched polyurethane (HBPU)/clay nanocomposites were prepared at different dose levels by in situ polymerization technique. The performances of epoxy-cured thermosetting nanocomposites are reported for the first time. The partially exfoliated structure of clay layers was confirmed by XRD and TEM. FTIR spectra indicate the presence of H bonding between nanoclay and the polymer matrix. The present investigation outlines the significant improvement of tensile strength, scratch hardness, thermostability, water vapor permeability, and adhesive strength without much influencing impact resistance, bending, and elongation at break of the nanocomposites compared to pristine HBPU thermoset. An increment of two times the tensile strength, 6 degrees C of melting point, and 111 degrees C of thermo-stability were achieved by the formation of nanocomposites. An excellent shape recovery of about 96-99% was observed for the nanocomposites. Thus, the formation of partially exfoliated clay/vegetable oil-based hyperbranched polyurethane nanocomposites significantly improved the performance.

Grinding temperature and energy ratio coe cient in MQL grinding of high-temperature nickel-base alloy by using di erent vegetable oils as base oil

Institute of Scientific and Technical Information of China (English)

Li Benkai; Li Changhe; Zhang Yanbin; Wang Yaogang; Jia Dongzhou; Yang Min

2016-01-01

Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grind-ing temperature, and energy ratio coefficient of MQL grinding were compared among the seven veg-etable oil types. Results revealed that (1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding tem-perature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less vis-cous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid;and (7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force, 87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7%energy ratio coefficient

Tariff Impact on the Domestic Price of Vegetable Oil in Iran and the Associated Issues

Directory of Open Access Journals (Sweden)

omid gilanpour

2015-05-01

Full Text Available This study uses vector error correction model to examine the effects of oilseeds, crude oil and vegetable oil tariffs on vegetable oil consumer price. Monthly data sets for the years 2004-2013 and VAR and VECM models were applied for this study. Research findings indicates only a long term equilibrium relation between the study variables .The effect of vegetable oil tariffs on consumer and producer price index are 0.4 and 0.07, respectively. Furthermore, one percent increase in the oil seeds and crude oil tariff, will increase consumer prices by 2.35, 0.19percent. The huge gap between the impacts of the two tariffs –e.g. oilseeds and crude oil tariffs- on consumer price shows that oil industries work with low efficiency. This practically doubles the impact of tariff on consumers. Accordingly, structural reform in the oil industry can develop oil production and prevent additional burden upon the consumer price.

HPLC-UV Polyphenolic Profiles in the Classification of Olive Oils and Other Vegetable Oils via Principal Component Analysis

Directory of Open Access Journals (Sweden)

Mireia Farrés-Cebrián

2016-12-01

Full Text Available High performance liquid chromatography-ultraviolet (HPLC-UV was applied to the analysis and characterization of olive oils and other vegetable oils. A chromatographic separation on a Zorbax Eclipse XDB-C8 reversed-phase column was proposed under gradient elution, employing 0.1% formic acid aqueous solution and methanol as mobile phase, for the determination of 14 polyphenols and phenolic acids, allowing us to obtain compositional profiles in less than 20 min. Acceptable sensitivity (limit of detection (LOD values down to 80 µg/L in the best of cases, linearity (r2 higher than 0.986, good run-to-run and day-to-day precisions (relative standard deviation (RSD values lower than 11.5%, and method trueness (relative errors lower than 6.8% were obtained. The proposed HPLC-UV method was then applied to the analysis of 72 oil samples (47 olive oils and 27 vegetable oils including sunflower, soy, corn, and mixtures of them. Analytes were recovered using a liquid–liquid extraction method employing ethanol:water 70:30 (v/v solution and hexane as extracting and defatting solvents, respectively. HPLC-UV polyphenolic profiles using peak areas were then analysed by principal component analysis (PCA to extract information from the most significant data contributing to the characterization and classification of olive oils against other vegetable oils, as well as among Arbequina and Picual olive oil varieties. PCA results showed a noticeable difference between olive oils and the other classes. In addition, a reasonable discrimination of olive oils as a function of fruit varieties was also encountered.

[Consumption of nuts and vegetal oil in people with type 1 diabetes mellitus].

Science.gov (United States)

Ferrer-García, Juan Carlos; Granell Vidal, Lina; Muñoz Izquierdo, Amparo; Sánchez Juan, Carlos

2015-06-01

Recent studies have demonstrated the cardiovascular benefits of the Mediterranean Diet, enriched with olive oil and nuts. People with diabetes, who have an increased risk of cardiovascular complications, could benefit greatly from following this type of eating pattern. Analysis of vegetable fats intake from nuts and olive oil in patients with 1 Diabetes Mellitus type (DM1). Transverse descriptive study comparing 60 people with type 1 Diabetes Mellitus (DM1) with 60 healthy individuals. We collect the frequency of consumption of vegetable oils and nuts and calculate the contribution of these foods in mono and polyunsaturated fatty acids (oleic acid, linoleic acid and α-linolenic acid). For data collection we designed a food frequency questionnaire specifically. We also collect anthropometric variables, cardiovascular risk factors and diabetes-related variables. Vegetable fat intake from vegetable oils (3.02 ± 1.14 vs 3.07 ± 1.27 portions/day, P = 0.822) and nuts (1.35 ± 2.24 vs 1.60 ± 2.44 portions/week, P = 0.560), was similar in both groups. The DM1 group consumed fewer portions of olive oil daily than the control group (2.55 ± 1.17 vs 3.02 ± 1.34 portions/day, P = 0.046). We detected a significantly lower intake of α-linolenic acid in the control group (1.13 ± 2.06 versus 2.64 ± 4.37 g/day, p = 0.018) while there were not differences in the rest of fatty acids (oleic acid 28.30 ± 18.13 vs 29.53 ± 16.90 g/day, P = 0.703; linoleic 13.70 ± 16.80 vs 15.45 ± 19.90 g/day, P = 0.605). In DM1, it not demonstrated an influence of the intake of vegetable fats and oils from nuts in the anthropometric, metabolic and diabetes-specific variables. In people with DM1, total intake of vegetable oils and nuts do not differ from the general population. However, the consumption of olive oil and the contribution of α-linolenic fatty acid derived from such fats are slightly lower than the general population. Although intake of vegetable oils and nuts in people with DM1

Ultrasound assisted PTC catalyzed saponification of vegetable oils using aqueous alkali.

Science.gov (United States)

Bhatkhande, B S; Samant, S D

1998-03-01

A few vegetable oils were saponified using aqueous KOH and different PTCs at room temperature in the presence of ultrasound. The extent of saponification was studied using the saponification value as a reference. Optimizations of various parameters such as time, selection of PTC, quantity of PTC, quantity of KOH and quantity of water were carried out using soyabean oil as a sample oil under sonication with stirring. To study the effect of ultrasound, the saponification was also carried out at 35 +/- 2 degrees C under different conditions, namely stirring, sonication, stirring and sonication, and heating at 100 degrees C. It was found that the heterogeneous liquid-liquid phase saponification of different vegetable oils using aq. KOH/CTAB was remarkably accelerated at 35 +/- 2 degrees C in the presence of ultrasound along with stirring.

Phase-transfer catalysis and ultrasonic waves II: saponification of vegetable oil.

Science.gov (United States)

Entezari, M H; Keshavarzi, A

2001-07-01

Saponification of oils which is a commercially important heterogeneous reaction, can be speeded up by the application of ultrasound in the presence of phase-transfer catalyst (PTC). This paper focuses on the ability of ultrasound to cause efficient mixing of this liquid-liquid heterogeneous reaction. Castor oil was taken as a model oil and the kinetic of the reaction was followed by the extent of saponification. The hydrolysis of castor oil was carried out with different PTC such as cetyl trimethyl ammonium bromide (CTAB), benzyl triethyl ammonium chloride (BTAC) and tetrabutyl ammonium bromide (TBAB) in aqueous alkaline solution. As hydroxyl anion moves very slowly from aqueous to oil phase, the presence of a PTC is of prime importance. For this purpose, cationic surfactants are selected. The sonication of biphasic system were performed by 20 kHz (simple horn and cup horn) and 900 kHz. It was found that CTAB was better than the two others and this could be related to the molecular structure of the PTCs. The effect of temperature was also studied on the saponification process. By increasing the temperature, the yield was also increased and this could be explained by intermolecular forces, interfacial tension and mass transfer. Saponification of three different vegetable oils shows that the almond oil is saponified easier than the two others and this could be related to their properties such as surface tension, viscosity and density.

Hydration of vegetable oils for high-grade Diesel fuel components; Hydrierung von Pflanzenoelen zu hochwertigen Dieselkraftstoffkomponenten

Energy Technology Data Exchange (ETDEWEB)

Endisch, M.; Olschar, M.; Kuchling, T. [TU Bergakademie Freiberg (Germany); Balfanz, U. [BP AG, Global Fuels Technology, Bochum (Germany)

2008-07-01

The legally regulated admixture of biogenic fuel components for diesel fuels are actually realized in Germany by an admixture of vegetable oil methylester (e.g. from rapeseed oil). The paper describes the hydration of vegetable oils as alternative to this procedure. Infrared and {sup 13}NMR spectroscopy were used to analyse the reaction kinetics for rapeseed, soy been and palm oil hydration. Experimental results of investigations under operational conditions using a continuous test facility and different vegetable oils identified the possibilities of this technology. The technology allows the high-yield production of diesel fuel components with certain numbers higher than average.

Determination of vegetable oils and fats adulterants in diesel oil by high performance liquid chromatography and multivariate methods.

Science.gov (United States)

Brandão, Luiz Filipe Paiva; Braga, Jez Willian Batista; Suarez, Paulo Anselmo Ziani

2012-02-17

The current legislation requires the mandatory addition of biodiesel to all Brazilian road diesel oil A (pure diesel) marketed in the country and bans the addition of vegetable oils for this type of diesel. However, cases of irregular addition of vegetable oils directly to the diesel oil may occur, mainly due to the lower cost of these raw materials compared to the final product, biodiesel. In Brazil, the situation is even more critical once the country is one of the largest producers of oleaginous products in the world, especially soybean, and also it has an extensive road network dependent on diesel. Therefore, alternatives to control the quality of diesel have become increasingly necessary. This study proposes an analytical methodology for quality control of diesel with intention to identify and determine adulterations of oils and even fats of vegetable origin. This methodology is based on detection, identification and quantification of triacylglycerols on diesel (main constituents of vegetable oils and fats) by high performance liquid chromatography in reversed phase with UV detection at 205nm associated with multivariate methods. Six different types of oils and fats were studied (soybean, frying oil, corn, cotton, palm oil and babassu) and two methods were developed for data analysis. The first one, based on principal component analysis (PCA), nearest neighbor classification (KNN) and univariate regression, was used for samples adulterated with a single type of oil or fat. In the second method, partial least square regression (PLS) was used for the cases where the adulterants were mixtures of up to three types of oils or fats. In the first method, the techniques of PCA and KNN were correctly classified as 17 out of 18 validation samples on the type of oil or fat present. The concentrations estimated for adulterants showed good agreement with the reference values, with mean errors of prediction (RMSEP) ranging between 0.10 and 0.22% (v/v). The PLS method was

A comparison of cold flow properties of biodiesel produced from virgin and used frying oil

Energy Technology Data Exchange (ETDEWEB)

Al-Shanableh, Filiz [Food Engineering Department, Near East University (Cyprus); Evcil, Ali; Govsa, Cemal [Mechanical Engineering Department, Near East University (Cyprus); Savasdylmac, Mahmut A. [Mechanical Engineering Department, Booazici University (Turkey)

2011-07-01

Bio-diesel can be produced from different kinds of feedstock. The purpose of this paper is to research and make the comparison of the cold flow properties of bio-diesel produced from refined-virgin frying vegetable oil (RVFVO) and waste frying vegetable oil (WFVO). As is known, bio-diesel fuel will have higher cloud points (CP), cold filter plugging points (CFPP) and pour points (PP) if it is derived from fat or oil which consists of significant amounts of saturated fatty compounds. Both RVFVO and WFVO were derived from the same cafeteria on a Near East University campus and converted to biodiesel fuel through base catalyzed transesterification reaction. As the current results show, there is no considerable difference in cold flow properties of the bio-diesel produced from RVFVO and WFVO. So WFVO seems be better positioned to serve as raw material in biodiesel production because of its lower cost and its environmental benefits.

Vegetable oils as hydraulic fluids for agricultural applications

Directory of Open Access Journals (Sweden)

Mendoza, G.

2011-03-01

Full Text Available The formulation of environmentally friendly lubricants following the criterion of the European EcoLabel is expensive owing to the lack of technological development in this area. The present work deals with the development of lubricant formulations from vegetable oils, in particular using high oleic sunflower oil as base fluid. These new biolubricants have to perform as good as the reference lubricants used in the real application (an agricultural tractor but with the additional condition and value of their biodegradability without toxicity. Formulation development has been performed by Verkol Lubricantes, involving the selection of the base oil and the design of the additive package. The investigation performed by Tekniker in the laboratory has covered different aspects, characterizing the most important physicochemical properties of the lubricants, including their behavior at low temperatures and their resistance to oxidation. The tribological properties of the new biolubricants have also been studied, analyzing their ability to protect the interacting surface from wear, as well as the level of friction generated during sliding. Moreover, the compatibility of the new formulated oil with all the seals present in the real application has been taken into consideration. The selected lubricant is now being tested in agricultural machinery from AGRIA.

La formulación de lubricantes amigables con el medioambiente siguiendo los criterios Europeos de la EcoLabel resulta cara debido a la falta de desarrollo tecnológico en esta área. En el presente trabajo se han desarrollado formulaciones de lubricantes a partir de aceites de origen vegetal, en particular empleando como aceite base el GAO (Girasol de Alto Oleico. Estos nuevos lubricantes deben presentar un comportamiento tan bueno como el de los lubricantes de referencia empleados en la aplicación real (un tractor agrícola, pero con la condición y valor añadido de ser biodegradables y no t

Biodiesel fuels from vegetable oils via catalytic and non-catalytic supercritical alcohol transesterifications and other methods: a survey

International Nuclear Information System (INIS)

Demirbas, Ayhan

2003-01-01

Vegetable oil fuels have not been acceptable because they were more expensive than petroleum fuels. With recent increases in petroleum prices and uncertainties concerning petroleum availability, there is renewed interest in vegetable oil fuels for Diesel engines. Dilution of oils with solvents and microemulsions of vegetable oils lowers the viscosity, but some engine performance problems still exist. The purpose of the transesterification process is to lower the viscosity of the oil. Pyrolysis produces more biogasoline than biodiesel fuel. Soap pyrolysis products of vegetable oils can be used as alternative Diesel engine fuel. Methyl and ethyl esters of vegetable oils have several outstanding advantages among other new renewable and clean engine fuel alternatives. The main factors affecting transesterification are the molar ratio of glycerides to alcohol, catalyst, reaction temperature and pressure, reaction time and the contents of free fatty acids and water in oils. The commonly accepted molar ratios of alcohol to glycerides are 6:1-30:1

Vegetable Oil-Based Hyperbranched Thermosetting Polyurethane/Clay Nanocomposites

Directory of Open Access Journals (Sweden)

Deka Harekrishna

2009-01-01

Full Text Available Abstract The highly branched polyurethanes and vegetable oil-based polymer nanocomposites have been showing fruitful advantages across a spectrum of potential field of applications.Mesua ferreaL. seed oil-based hyperbranched polyurethane (HBPU/clay nanocomposites were prepared at different dose levels by in situ polymerization technique. The performances of epoxy-cured thermosetting nanocomposites are reported for the first time. The partially exfoliated structure of clay layers was confirmed by XRD and TEM. FTIR spectra indicate the presence of H bonding between nanoclay and the polymer matrix. The present investigation outlines the significant improvement of tensile strength, scratch hardness, thermostability, water vapor permeability, and adhesive strength without much influencing impact resistance, bending, and elongation at break of the nanocomposites compared to pristine HBPU thermoset. An increment of two times the tensile strength, 6 °C of melting point, and 111 °C of thermo-stability were achieved by the formation of nanocomposites. An excellent shape recovery of about 96–99% was observed for the nanocomposites. Thus, the formation of partially exfoliated clay/vegetable oil-based hyperbranched polyurethane nanocomposites significantly improved the performance.

The flexfuel tractor. Invesigations on the combustion behaviour of vegetable oil fuels and on the discernability of fossil and biogenic fuels; Der Flexfuel Traktor. Untersuchungen zum Verbrennungsverhalten von Pflanzenoelkraftstoffen und zur Unterscheidbarkeit fossiler und biogener Kraftstoffe

Energy Technology Data Exchange (ETDEWEB)

Dieringer, Stefanie

2012-07-01

Increasing energy prices, especially for fossil fuels, as well as the necessity to reduce CO{sub 2} emissions are emphasizing the advantages of self-produced vegetable oil fuels in agriculture. Monetary advantages are depending on basic conditions like farm size or tax legislation, which can be changing locally as well as temporarily. Due to the differing properties of diesel and vegetable oil fuel, engines have to be adapted to each fuel to fulfil performance requirements as well as emission limits and reliability. Knowing that there are advantages of vegetable oil compared to diesel fuel, though not always and everywhere present, it becomes obvious that the well known flexible fuel concept of passenger cars should be adapted for diesel engines of agricultural machines. So called flexfuel engines imply the detection of the fuel type and an automated adjustment of the engine control parameters without any manual action of an operator. Therefore, the first step consists of the evaluation of the combustion properties of rapeseed, sunflower, jatropha and false flax oil compared to diesel fuel. The tested vegetable oils showed very similar behaviour in the tested common rail diesel engine. Especially the limited emissions were met with the same engine control software with all vegetable oils. In consequence it is possible to realize a flexfuel engine using the two engine control maps available at the moment, one for diesel and the other one for vegetable oil fuels. For further investigations one oil type, namely rapeseed oil was selected to test the combustion behaviour of fuel blends made of diesel and vegetable oil. The goal was to determine the blend ratio of vegetable oil and diesel fuel at which the engine control software has to be changed from the diesel to the vegetable oil map automatically. If the fuel consists of 40% or more vegetable oil, the vegetable oil engine control map has to be selected in order to fulfil legal emission limits. Finally the

Extent of Microbial Contamination of Refined and Unrefined Vegetable oils sold in South-west Nigeria

Directory of Open Access Journals (Sweden)

Oluwafemi Flora

2018-04-01

Full Text Available Oils constitute a major source of plant-based protein. A major limitation to optimal oil consumption in sub-tropical region is fungal infestation and consequent mycotoxin contamination. Ten refined and eight unrefined vegetable oils were randomly purchase from open markets and screened for microbial contamination using standard microbial procedures. Twenty six fungi isolates were obtained from the vegetable oil samples, the isolates were identified as Aspergillus fumigatus (43.0%, Mucor (17.9%, Saccharomyces cerevisiae (10.7%, Aspergillus niger (7.1%, Aspergillus flavus (7.1%, Penicillium spp (7.1%, Aspergillus oryzae (3.6%, Mucor (17.9% and Rhizopus spp (3.6%. Five out of the ten refined vegetable oil samples had no fungal contamination. A. flavus and A. oryzae were absent in all the refined oil samples while A. niger was absent in all the unrefined oil samples. Isolation of mycotoxigenic fungi such as Aspergillus spp. is of vital importance in the food industry. Education and training of processors and consumers is recommended.

Physicochemical characterization of Quassia undulata seed oil for ...

African Journals Online (AJOL)

... peroxide value (6.756). The values obtained from Q. undulata were uniquely different from common vegetable oils but with a superior combination of properties to suit a promising industrial process such as biodiesel production. Keywords: Quassia undulata, physicochemical properties, vegetable oil, biodiesel production ...

New antioxidants and antioxidant systems for improvement of the stability of vegetable oils and fish oils

Science.gov (United States)

Most vegetable oils and fish oils contain polyunsaturated fatty acids ranging from 18 carbons with two to three double bonds, to 22 or 24 carbons, and up to six double bonds. Nutritional research over the years has indicated that individual fatty acids from the diet play a complex role in nutrition ...

Heterogeneous hydrogenation of vegetable oils : A literature review

NARCIS (Netherlands)

Veldsink, JW; Bouma, MJ; Schoon, NH; Beenackers, AACM

1997-01-01

Hardening of vegetable oils is reviewed from an engineering point of view. The present review focuses on kinetics of the hydrogenation and relevant transport and adsorption steps. It aims to contribute to accelerate new research to improve substantially on selectivities in general and a decrease of

HVO, hydrotreated vegetable oil. A premium renewable biofuel for diesel engines

Energy Technology Data Exchange (ETDEWEB)

Mikkonen, Seppo [Neste Oil, Porvoo (Finland); Honkanen, Markku; Kuronen, Markku [Neste Oil, Espoo (Finland)

2013-06-01

HVO is renewable paraffinic diesel fuel produced from vegetable oils or animal fats by hydrotreating and isomerization. Composition is similar to GTL. HVO is not ''biodiesel'' which is a definition reserved for FAME. HVO can be used in diesel fuel without any ''blending wall'' as well as in addition to the FAME in EN 590. As a blending component HVO enhances fuel properties thanks to its high cetane, zero aromatics and reasonable distillation range. HVO can be used for upgrading gas oils to meet diesel fuel standard and for producing premium diesel fuels. HVO is comparable to fossil diesel regarding fuel logistics, stability, water separation and microbiological growth. The use of HVO as such or in blends reduces NO{sub x} and particulate emissions. Risks for fuel system deposits and engine oil deterioration are low. Combustion is practically ash-free meaning low risk for exhaust aftertreatment life-time. Winter grade fuels down to -40 C cloud point can be produced by HVO process from many kinds of feedstocks. HVO is fully accepted by directives and fuel standards. (orig.)

Effect of the use of waste vegetable oil based biodiesel on the landscape in diesel engines

Directory of Open Access Journals (Sweden)

Bereczky Akos

2017-01-01

Full Text Available Petroleum-based fuels are now widely known as environmentally unfriendly because of non-renewable supplies and its contribution to environmental pollution. The challenge, therefore is to ensure appropriate energy supplies at minimum cost. There is an increasing energy demand in the world and nowadays it can be fulfilled only on the basis of fossil fuels. Therefore, it is necessary to evolve a renewable energy source with lower environmental impact. One alternative solution can be oils of plant origin, like vegetable oils and non-edible oils. With waste vegetable oil methyl ester, biofuel dependency can be decreased. Therefore, the aim of this research paper is to analyze the economic and environmental effect of waste vegetable oil methyl ester compared to fossil fuels. In some cases only the age of vehicles could raise burdens to biofuel utilization in road vehicles. Transport and energy policy – on a large scale – can play an important role in fuel consumption. Author is aware that waste vegetable oil methyl ester can play only a limited role in biofuel substitution.

Burn drug made from ozonated vegetable oil mixture with white tumeric and cassava leaves extract

Directory of Open Access Journals (Sweden)

Moulydia Farah

2018-01-01

Full Text Available This research aims to create a burn treatment performed with ozonation process from a mixture of vegetable oil and added extracts of herbal ingredients. Ozonation on vegetable oils proven to kill bacteria and safe for the body. Ozonated vegetable oil produced from the ozone reactor batch process by doing a variety of extraction mixture to Oleozon® and vegetable oils. Then the results of ozonation is added extracts of herbal ingredients that cassava leaves and white turmeric to increase effectiveness in killing bacteria. Cassava leaves have anti-inflammatory agent, namely Vitamin C. While white turmeric Curcuma zedoaria have substance, which of the two compounds can inhibit and kill bacteria. The quality of ozonated oil (Oleozon® analytically were tested by the method of iodine number, acid number, peroxide number, and FTIR. Ozonation increased the peroxide and acid values for both oils, the increase being higher for mixture of coconut oil and soybean oil. The results of such mixing is then tested in bacteria to determine their effectiveness in killing the bacteria. The best ozonation condition is in an increase of 386,85% acid value, peroxide value about 102,91 meq/kg oil, and decrease in iodine number up to 21%. The result showed that under these conditions, ozonized oil has an antiseptic effect against Staphylococcus aureus. The final results of this study are expected to be a new innovation in the healing of skin wounds caused by burns as an anti-inflammatory that is effective, safe, and environmentally friendly.

Enzymatic interesterification of vegetable oil/ fish oil blend for margarine production

DEFF Research Database (Denmark)

Ibrahim, Nuzul Amri Bin; Xu, Xuebing

the desired properties. In this study, palm stearin (PS), palm kernel oil (PKO) and fish oil (FO) are blended and modified by enzymatic interesterification. PS functioned as the hard stock, PKO as the soft oil and FO as a source for eicosapentaenoic acid (EPA)/ docosahexaenoic acid (DHA). The purpose...... cause the product to be susceptible to oxidation due to the presence of high content of polyunsaturated fatty acids. Furthermore, FO could also influence the melting properties of the product. Therefore, in addition to determining the fatty acid position on the glycerol backbone, it is also pertinent...

Synthesis of biodiesel from waste vegetable oil with large amounts of free fatty acids using a carbon-based solid acid catalyst

Energy Technology Data Exchange (ETDEWEB)

Shu, Qing; Gao, Jixian; Nawaz, Zeeshan; Liao, Yuhui; Wang, Dezheng; Wang, Jinfu [Beijing Key Laboratory of Green Chemical Reaction Engineering and Technology, Department of Chemical Engineering, Tsinghua University, Beijing 100084 (China)

2010-08-15

A carbon-based solid acid catalyst was prepared by the sulfonation of carbonized vegetable oil asphalt. This catalyst was employed to simultaneously catalyze esterification and transesterification to synthesis biodiesel when a waste vegetable oil with large amounts of free fatty acids (FFAs) was used as feedstock. The physical and chemical properties of this catalyst were characterized by a variety of techniques. The maximum conversion of triglyceride and FFA reached 80.5 wt.% and 94.8 wt.% after 4.5 h at 220 C, when using a 16.8 M ratio of methanol to oil and 0.2 wt.% of catalyst to oil. The high catalytic activity and stability of this catalyst was related to its high acid site density (-OH, Broensted acid sites), hydrophobicity that prevented the hydration of -OH species, hydrophilic functional groups (-SO{sub 3}H) that gave improved accessibility of methanol to the triglyceride and FFAs, and large pores that provided more acid sites for the reactants. (author)

Demonstration study on direct use of waste vegetable oil as car fuel

International Nuclear Information System (INIS)

Remoto, Yasuyuki; Zeeren, Nyamgerel; Ushiyama, Izumi

2009-01-01

Full text: Various kinds of vegetable oil and waste cooking oil are in fact used as car fuel all over the world. In general, 'bio-diesel' i.e. fatty acid methyl ester extracted from such oil is utilized as fuel for vehicles. However bio-diesel has some problems such as byproduct and waste materials created during transesterification. An alternative method is the direct use of vegetable oil as car fuel through installation of a heater unit in the car to decrease vegetable oil viscosity. However little data has been reported concerning this method. The authors of this study carried out performance tests on the direct use of waste cooking oil using a car with a heater unit and found its high potential. Moreover, the authors compared the environmental load of direct use with biodiesel and light oil by carrying out life cycle inventory to clarify the superiority of direct use. First, the authors made a car to test waste cooking oil as fuel by equipping a heater unit, filter and sub tank for light oil to a used Toyota Estima Diesel KD-CXR10G. The car can be driven on road using only waste cooking oil, although a little light oil is necessary for starting the engine. The authors, then, carried out chassis dynamo tests and on-road tests using the car. The car showed similar performance and could be driven on road for over half a year without any problems in both cases using either waste cooking oil or light oil as fuel. Next, authors carried out life cycle inventory and compared the environmental loads of direct use of waste cooking oil with biodiesel from waste cooking oil and light oil. The data for life cycle inventory were obtained from tests on direct use, from a factory in Japan for bio-diesel and from the Life Cycle Assessment Society of Japan database for light oil, respectively. The CO 2 emission rates were 73.9, 12.7 and 7.06 [kg-CO 2 / GJ] for light oil, bio-diesel from waste cooking oil and the direct use of waste cooking oil, respectively. The superiority of

Recycled palm oil spoilage: Correlation between physicochemical properties and oleophilicity

Science.gov (United States)

Kadir, Ili Afiqa Ab; Zubairi, Saiful Irwan; Jurid, Lailatul Syema

2016-11-01

Palm oil is widely used for domestic and commercial frying due to its techno-economic advantages as compared to other vegetable oils. However, if the oil is used beyond its recommended usage cycle, it might lead to oil spoilage. Therefore this study focuses on the comprehensive analysis of chemical and physical properties of recycled palm oil. Recycled palm oil was prepared by frying potato strips up to 4 batches; 5 cycles for each batch) was carried out with potato (g)-to-oil (ml) ratio of 3/20 prior to physico-chemical analysis (moisture content, color measurement, viscosity, density and iodine value. From 5 tests used to indicate physico-chemical properties of recycled palm oil, only color measurement, viscosity and IV shows results accordingly to theories. Whereas moisture content and density were not comply to theories. With increasing frying times, recycled palm oil color has been darker due to chemical reaction that occurs during frying. The trend line illustrates that with increasing frying times, recycled palm oil lightness decreases. It also means that its color has been darker. Meanwhile, b* rate increase indicating that recycled palm oil show tendency towards green color. Whereas, a* rate decreased, showing low tendency towards red color. Viscosity and moisture content increase with frying cycle. This situation occurred might be due to formation of hydrolysis products which are volatile while frying process. But the remaining non-volatile compounds among the hydrolysis products might also accumulate in palm oil and thus affect the total oil/fat chemical changes. Meanwhile the density of palm oil was quite constant at 0.15 g/cm3 except for cycle 2 with 0.17 g/cm3. The result obtained from this experiment were comply with previous study that stated frying batch number is a significant variable (a = 0.05) affecting the density of oil only after 20 frying batch. The contact angle of recycled palm oil on PHBV thin film was more than 90 °. Hence it shows

Finding the food-fuel balance. Supply and demand dynamics in global vegetable oil markets

Energy Technology Data Exchange (ETDEWEB)

Savanti, P.

2012-10-15

Demand for vegetable oils for food and biofuel use is expected to increase by an additional 23 million tonnes by 2016; however supply is expected to struggle to keep up with this demand, according to this Rabobank report. Vegetable oil stocks have reached a 38 year low this year due in large part to constraints such as land availability and adverse weather.

Evaluation of Physicochemical Properties of Biodiesel Produced ...

African Journals Online (AJOL)

The non-edible vegetable oils of Jatropha curcas, neem, castor, rubber and edible oils of soyabean and cotton were investigated for their use as biodiesel feedstock. The analysis of different oil properties, fuel properties of non-edible and edible vegetable oils were investigated in detail. A two-step and transesterification ...

Evaluation of antioxidants stability by thermal analysis and its protective effect in heated edible vegetable oil

Directory of Open Access Journals (Sweden)

Seme Youssef Reda

2011-06-01

Full Text Available In this work, through the use of thermal analysis techniques, the thermal stabilities of some antioxidants were investigated, in order to evaluate their resistance to thermal oxidation in oils, by heating canola vegetable oil, and to suggest that antioxidants would be more appropriate to increase the resistance of vegetable oils in the thermal degradation process in frying. The techniques used were: Thermal Gravimetric (TG and Differential Scanning Calorimetry (DSC analyses, as well as an allusion to a possible protective action of the vegetable oils, based on the thermal oxidation of canola vegetable oil in the laboratory under constant heating at 180 ºC/8 hours for 10 days. The studied antioxidants were: ascorbic acid, sorbic acid, citric acid, sodium erythorbate, BHT (3,5-di-tert-butyl-4-hydroxytoluene, BHA (2, 3-tert-butyl-4-methoxyphenol, TBHQ (tertiary butyl hydroquinone, PG (propyl gallate - described as antioxidants by ANVISA and the FDA; and also the phytic acid antioxidant and the SAIB (sucrose acetate isobutyrate additive, which is used in the food industry, in order to test its behavior as an antioxidant in vegetable oil. The following antioxidants: citric acid, sodium erythorbate, BHA, BHT, TBHQ and sorbic acid decompose at temperatures below 180 ºC, and therefore, have little protective action in vegetable oils undergoing frying processes. The antioxidants below: phytic acid, ascorbic acid and PG, are the most resistant and begin their decomposition processes at temperatures between 180 and 200 ºC. The thermal analytical techniques have also shown that the SAIB antioxidant is the most resistant to oxidative action, and it can be a useful choice in the thermal decomposition prevention of edible oils, improving stability regarding oxidative processes.

Rapid determination of saponification value and polymer content of vegetable and fish oils by terahertz spectroscopy.

Science.gov (United States)

Jiang, Feng Ling; Ikeda, Ikuo; Ogawa, Yuichi; Endo, Yasushi

2012-01-01

A rapid method for determining the saponification value (SV) and polymer content of vegetable and fish oils using the terahertz (THz) spectroscopy was developed. When the THz absorption spectra for vegetable and fish oils were measured in the range of 20 to 400 cm⁻¹, two peaks were seen at 77 and 328 cm⁻¹. The level of absorbance at 77 cm⁻¹ correlated well with the SV. When the THz absorption spectra of thermally treated high-oleic safflower oils were measured, the absorbance increased with heating time. The polymer content in thermally treated oil correlated with the absorbance at 77 cm⁻¹. These results demonstrate that the THz spectrometry is a suitable non-destructive technique for the rapid determination of the SV and polymer content of vegetable and fish oils.

Systematic methodology and property prediction of fatty systems for process design/analysis in the oil and fat industry

DEFF Research Database (Denmark)

Díaz Tovar, Carlos Axel; Ceriani, Roberta; Gani, Rafiqul

2010-01-01

in the vegetable oil were defined. Basic and critical properties were then computed by means of appropriate property prediction software. Temperature dependant properties were modeled using and extending available correlations. The process model was developed through the PRO II commercial simulator and validated......A systematic model based methodology has been developed and its application highlighted through the solvent recovery section of a soybean oil extraction process, with emphasis on the effect of design variables on the process performance. First, the most representative compounds present...

Soil TPH Concentration Estimation Using Vegetation Indices in an Oil Polluted Area of Eastern China

Science.gov (United States)

Zhu, Linhai; Zhao, Xuechun; Lai, Liming; Wang, Jianjian; Jiang, Lianhe; Ding, Jinzhi; Liu, Nanxi; Yu, Yunjiang; Li, Junsheng; Xiao, Nengwen; Zheng, Yuanrun; Rimmington, Glyn M.

2013-01-01

Assessing oil pollution using traditional field-based methods over large areas is difficult and expensive. Remote sensing technologies with good spatial and temporal coverage might provide an alternative for monitoring oil pollution by recording the spectral signals of plants growing in polluted soils. Total petroleum hydrocarbon concentrations of soils and the hyperspectral canopy reflectance were measured in wetlands dominated by reeds (Phragmites australis) around oil wells that have been producing oil for approximately 10 years in the Yellow River Delta, eastern China to evaluate the potential of vegetation indices and red edge parameters to estimate soil oil pollution. The detrimental effect of oil pollution on reed communities was confirmed by the evidence that the aboveground biomass decreased from 1076.5 g m−2 to 5.3 g m−2 with increasing total petroleum hydrocarbon concentrations ranging from 9.45 mg kg−1 to 652 mg kg−1. The modified chlorophyll absorption ratio index (MCARI) best estimated soil TPH concentration among 20 vegetation indices. The linear model involving MCARI had the highest coefficient of determination (R 2 = 0.73) and accuracy of prediction (RMSE = 104.2 mg kg−1). For other vegetation indices and red edge parameters, the R2 and RMSE values ranged from 0.64 to 0.71 and from 120.2 mg kg−1 to 106.8 mg kg−1 respectively. The traditional broadband normalized difference vegetation index (NDVI), one of the broadband multispectral vegetation indices (BMVIs), produced a prediction (R 2 = 0.70 and RMSE = 110.1 mg kg−1) similar to that of MCARI. These results corroborated the potential of remote sensing for assessing soil oil pollution in large areas. Traditional BMVIs are still of great value in monitoring soil oil pollution when hyperspectral data are unavailable. PMID:23342066

Some properties of castor oil affecting its performance as a capacitor impregnant and their significance to future impregnant research

International Nuclear Information System (INIS)

Boicourt, G.P.

1975-01-01

For a considerable time castor oil and polychlorinated biphenyl (PCB) have been the principal impregnants used in energy-storage capacitors. Castor oil has proven to be better than PCB for pulsed applications. PCB's have come under attack as an environmental hazard, while castor oil is a vegetable product and its supply and quality are subject to fluctuation. These two facts make the development of new impregnants desirable. The properties of PCB as a capacitor impregnant are well known. This paper first compares a number of properties of castor oil and PCB's. A comparison is made between the lives of castor oil capacitors and comparable PCB energy-storage capacitors. Some of the physical and chemical properties of castor oil which make it a good pulse capacitor impregnant are examined. These properties can be used as a guide for future research on new pulse capacitor impregnants

Plasticizer contamination in edible vegetable oil in a U.S. retail market.

Science.gov (United States)

Bi, Xiaolong; Pan, Xiaojun; Yuan, Shoujun; Wang, Qiquan

2013-10-02

With the wide application of plastics, the contamination of plasticizers migrating from plastic materials in the environment is becoming ubiquitous. The presence of phthalates, the major group of plasticizers, in edible items has gained increasingly more concern due to their endocrine disrupting property. In this study, 15 plasticizers in 21 edible vegetable oils purchased from a U.S. retail market were analyzed using gas chromatograph-mass spectrometry. Di(2-ethylhexyl) phthalate (DEHP) and diisobutyl phthalate (DiBP) were detected in all oil samples. Benzylbutyl phthalate (BzBP), dibutyl phthalate (DBP), and diethyl phthalate (DEP) were detected at a rate of 95.2, 90.5, and 90.5%, respectively. The detection rates for all other plasticizers ranged from 0 to 57.1%. The content of total plasticizers in oil samples was determined to be 210-7558 μg/kg, which was comparable to the content range in oil marketed in Italy. Although no significant difference (p = 0.05) in the total content of plasticizer was observed among oil species (soybean, canola, corn, and olive), the wider range and higher average of total content of plasticizers in olive oil than other oil species indicated the inconsistence of plasticizer contamination in olive oil and a possible priority for quality monitoring. No significant difference (p = 0.05) in the total content of plasticizers was found among glass-bottle (n = 4), plastic-bottle (n = 14), and metal-can (n = 3) packaging, implying that oil packaging is not the major cause of plasticizer contamination. The daily intake amount of plasticizers contained in edible oil on this U.S. retail market constituted only a minimum percentage of reference dose established by US EPA, thus no obvious toxicological effect might be caused. However, the fact that DEHP content in two olive oils exceeded relevant special migration limits (SMLs) of Europe and China might need attention.

Replacing Fish Oil with Vegetable Oils in Salmon Feed Increases Hepatic Lipid Accumulation and Reduces Insulin Sensitivity in Mice

DEFF Research Database (Denmark)

Midtbø, Lisa Kolden

Background: Due to a growing global aquaculture production, fish oil (FO) and fish meal (FM) are partly replaced with vegetable ingredients in aqua feed for Atlantic salmon. These replacements in the feed lead to an altered fatty acid composition in the salmon fillet. We aimed to investigate how...... these changes affects obesity development and insulin sensitivity in mice eating the salmon. In addition, we wanted to investigate how the background diet affects the antiobesity effect of FO. Results: Western diets (WDs) were produced containing salmon fed either FO (WD-FO), or with partly replacement (80......%) of FO with different vegetable oils (VOs); rape seed oil (WDRO), olive oil (WD-OO) or soybean oil (WD-SO). These diets were given to C57BL/6J mice, and mice had higher hepatic lipid accumulation and lower insulin sensitivity when given WD-SO compared with WD-FO. Mice given WD-SO had higher hepatic...

Fuel Continuous Mixer ? an Approach Solution to Use Straight Vegetable Oil for Marine Diesel Engines

Directory of Open Access Journals (Sweden)

Đặng Van Uy

2018-03-01

Full Text Available The vegetable oil is well known as green fuel for diesel engines due to its low sunphur content and renewable stock. However, there are some problems raising when vegetable oil is used as fuel for diesel engines such as highly effected by cold weather, lower general efficiency, separation in layer if mixed with diesel oil and so on. To overcome that disadvantiges, the authors propose a new idea that to use a continuous fuel mixer to blend vegetable oil with diesel oil to make so called a mixed fuel supplying to diesel engines inline. In order to ensure a quality of the mixed fuel created by continuous mixer, a homogeneous testing was introduced with believable results. Then, the continuous mixer has been installed into fuel supply system of diesel engine 6LU32 at a lab of Vietnam Maritime University in terms of checking a real operation of the fuel continuous mixer with diesel engine.

Hydroprocesssing of light gas oil - rape oil mixtures

Energy Technology Data Exchange (ETDEWEB)

Walendziewski, Jerzy; Stolarski, Marek; Luzny, Rafal; Klimek, Bartlomiej [Faculty of Chemistry, Wroclaw University of Technology, ul. Gdanska 7/9, 50-310 Wroclaw (Poland)

2009-05-15

Two series of experiments of hydroprocessing of light gas oil - rape oil mixtures were carried out. The reactor feed was composed of raw material: first series - 10 wt.% rape oil and 90 wt.% of diesel oil; second series - 20 wt.% rape oil and 80 wt.% of diesel oil. Hydroprocessing of both mixtures was performed with the same parameter sets, temperature (320, 350 and 380 C), hydrogen pressure 3 and 5 MPa, LHSV = 2 h{sup -} {sup 1} and hydrogen feed ratio of 500 Nm{sup 3}/m{sup 3}. It was stated that within limited range it is possible to control vegetable oil hydrogenolysis in the presence of light gas oil fraction (diesel oil boiling range) through the proper selection of the process parameters. Hydrogenolysis of ester bonds and hydrogenation of olefinic bonds in vegetable oils are the main reactions in the process. Basic physicochemical properties of the obtained hydroprocessed products are presented. (author)

Influence of the processed sunflower oil on the cement properties

Science.gov (United States)

Fleysher, A. U.; Tokarchuk, V. V.; Sviderskiy, V. A.

2015-01-01

Used oils (vegetable oil, animal oil, engine oil, etc.), which are essentially industrial wastes, have found application as secondary raw materials in some braches of industry. In particular, the only well-known and commonly-used way of utilizing wastes of vegetable oils is to apply them as raw materials in the production of biodiesel. The goal of the present study is to develop a conceptually new way of vegetable oil wastes utilization in the building industry. The test admixture D-148 was obtained from the processing of wastes of sunflower oil and it mainly consists of fatty acid diethanolamide. The test admixture was added to the cement system for the purpose of studying its influence on water demand, flowability, setting times, compressive strength and moisture adsorption. The test admixture D-148 at the optimal content 0. 2 weight % causes 10% decrease in water demand, 1.7 time increase in flowability (namely spread diameter), 23% increase in grade strength and 34% decrease in moisture adsorption. The results of the present investigation make it possible to consider the final product of the waste sunflower oil processing as multifunctional plasticizing-waterproofing admixture.

The Influence and Compatibility of Vegetable Oils and other ...

African Journals Online (AJOL)

The vegetable oils used as skin permeation enhancers were selected on the basis of compatibility studies data. A total of eight monolithic systems were prepared by using different concentrations of drug-polymers-permeation enhancers. The permeation parameters, flux, permeability coefficient, enhancement ratio and ...

Analysis of polycyclic aromatic hydrocarbons in vegetable oils combining gel permeation chromatography with solid-phase extraction clean-up

DEFF Research Database (Denmark)

Fromberg, Arvid; Højgård, A.; Duedahl-Olesen, Lene

2007-01-01

system equipped with a GPC column (S-X3) and pre-packed silica SPE columns for the subsequent clean-up and finally gas chromatography-mass spectrometry (GC-MS) determination. The method was validated for the determination of PAHs in vegetable oils and it can meet the criteria for the official control...... of benzo[a]pyrene levels in foods laid down by the Commission of the European Communities. A survey of 69 vegetable oils sampled from the Danish market included olive oil as well as other vegetable oils such as rapeseed oil, sunflower oil, grape seed oil and sesame oil. Levels of benzo[a]pyrene in all......A semi-automatic method for the determination of polycyclic aromatic hydrocarbons (PAHs) in edible oils using a combined gel permeation chromatography/solid-phase extraction (GPC/SPE) clean-up is presented. The method takes advantage of automatic injections using a Gilson ASPEC XL sample handling...

Chitosan-Based Coating with Antimicrobial Agents: Preparation, Property, Mechanism, and Application Effectiveness on Fruits and Vegetables

Directory of Open Access Journals (Sweden)

Yage Xing

2016-01-01

Full Text Available Chitosan coating is beneficial to maintaining the storage quality and prolonging the shelf life of postharvest fruits and vegetables, which is always used as the carrier film for the antimicrobial agents. This review focuses on the preparation, property, mechanism, and application effectiveness on the fruits and vegetables of chitosan-based coating with antimicrobial agents. Chitosan, derived by deacetylation of chitin, is a modified and natural biopolymer as the coating material. In this article, the safety and biocompatible and antimicrobial properties of chitosan were introduced because these attributes are very important for its application. The methods to prepare the chitosan-based coating with antimicrobial agents, such as essential oils, acid, and nanoparticles, were developed by other researchers. Meanwhile, the application of chitosan-based coating is mainly due to its antimicrobial activity and other functional properties, which were investigated, introduced, and analyzed in this review. Furthermore, the surface and mechanical properties were also investigated by researchers and concluded in this article. Finally, the effects of chitosan-based coating on the storage quality, microbial safety, and shelf life of fruits and vegetables were introduced. Their results indicated that chitosan-based coating with different antimicrobial agents would probably have wide prospect in the preservation of fruits and vegetables in the future.

Mechanism of formation of 3-chloropropan-1,2-diol (3-MCPD) esters under conditions of the vegetable oil refining.

Science.gov (United States)

Šmidrkal, Jan; Tesařová, Markéta; Hrádková, Iveta; Berčíková, Markéta; Adamčíková, Aneta; Filip, Vladimír

2016-11-15

3-MCPD esters are contaminants that can form during refining of vegetable oils in the deodorization step. It was experimentally shown that their content in the vegetable oil depends on the acid value of the vegetable oil and the chloride content. 3-MCPD esters form approximately 2-5 times faster from diacylglycerols than from monoacylglycerols. It has been proved that the higher fatty acids content in the oil caused higher 3-MCPD esters content in the deodorization step. Neutralization of free fatty acids in the vegetable oil before the deodorization step by alkaline carbonates or hydrogen carbonates can completely suppress the formation of 3-MCPD esters. Potassium salts are more effective than sodium salts. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermal Properties of Jojoba Oil Between 20°C and 45°C

Science.gov (United States)

Lara-Hernández, G.; Flores-Cuautle, J. J. A.; Hernandez-Aguilar, C.; Suaste-Gómez, E.; Cruz-Orea, A.

2017-08-01

Vegetable oils have been widely studied as biofuel candidates. Among these oils, jojoba ( Simmondsia chinensis) oil has attracted interest because it is composed almost entirely of wax esters that are liquid at room temperature. Consequently, it is widely used in the cosmetic and pharmaceutical industries. To date, research on S. chinensis oil has focused on to its use as a fuel and its thermal stability, and information about its thermal properties is scarce. In the present study, the thermal effusivity and conductivity of jojoba oil between 20°C and 45°C were obtained using the inverse photopyroelectric and hot-ball techniques. The feasibility of an inverse photopyroelectric method and a hot-ball technique to monitor the thermal conductivity, and the thermal effusivity of the S. chinensis is demonstrated. The thermal effusivity decreased from 538 W\\cdot s^{1/2}\\cdot m^{-2}\\cdot K^{-1} to 378 W\\cdot s^{1/2}m^{-2}\\cdot K^{-1} as the temperature increased, whereas the thermal conductivity remained the same over the temperature range investigated in this study. The obtained results provide insight into the thermal properties of S. chinensis oil between 20°C and 45°C.

Green Diesel from Hydrotreated Vegetable Oil Process Design Study

NARCIS (Netherlands)

Hilbers, T.J.; Sprakel, Lisette Maria Johanna; van den Enk, L.B.J.; Zaalberg, B.; van den Berg, Henderikus; van der Ham, Aloysius G.J.

2015-01-01

A systematic approach was applied to study the process of hydrotreating vegetable oils. During the three phases of conceptual, detailed, and final design, unit operations were designed and sized. Modeling of the process was performed with UniSim Design®. Producing green diesel and jet fuel from

The effect of nanoparticle surfactant polarization on trapping depth of vegetable insulating oil-based nanofluids

Energy Technology Data Exchange (ETDEWEB)

Li, Jian, E-mail: lijian@cqu.edu.cn; Du, Bin; Wang, Feipeng; Yao, Wei; Yao, Shuhan

2016-02-05

Nanoparticles can generate charge carrier trapping and reduce the velocity of streamer development in insulating oils ultimately leading to an enhancement of the breakdown voltage of insulating oils. Vegetable insulating oil-based nanofluids with three sizes of monodispersed Fe{sub 3}O{sub 4} nanoparticles were prepared and their trapping depths were measured by thermally stimulated method (TSC). It is found that the nanoparticle surfactant polarization can significantly influence the trapping depth of vegetable insulating oil-based nanofluids. A nanoparticle polarization model considering surfactant polarization was proposed to calculate the trapping depth of the nanofluids at different nanoparticle sizes and surfactant thicknesses. The results show the calculated values of the model are in a fairly good agreement with the experimental values. - Highlights: • Three different sized Fe{sub 3}O{sub 4} vegetable-oil based nanofluids was successfully prepared. • The trapping depth of the Fe{sub 3}O{sub 4} nanofluids was investigated. • A new model considering surfactant polarization was proposed to calculate the trapping depth of the nanofluids.

Kolkhoung (Pistacia khinjuk Hull Oil and Kernel Oil as Antioxidative Vegetable Oils with High Oxidative Stability and Nutritional Value

Directory of Open Access Journals (Sweden)

Maryam Asnaashari

2015-01-01

Full Text Available In this study, in order to introduce natural antioxidative vegetable oil in food industry, the kolkhoung hull oil and kernel oil were extracted. To evaluate their antioxidant efficiency, gas chromatography analysis of the composition of kolkhoung hull and kernel oil fatty acids and high–performance liquid chromatography analysis of tocopherols were done. Also, the oxidative stability of the oil was considered based on the peroxide value and anisidine value during heating at 100, 110 and 120 °C. Gas chromatography analysis showed that oleic acid was the major fatty acid of both types of oil (hull and kernel and based on a low content of saturated fatty acids, high content of monounsaturated fatty acids, and the ratio of ω-6 and ω-3 polyunsaturated fatty acids, they were nutritionally well-balanced. Moreover, both hull and kernel oil showed high oxidative stability during heating, which can be attributed to high content of tocotrienols. Based on the results, kolkhoung hull oil acted slightly better than its kernel oil. However, both of them can be added to oxidation–sensitive oils to improve their shelf life.

Sensor and Methodology for Dielectric Analysis of Vegetal Oils Submitted to Thermal Stress

Directory of Open Access Journals (Sweden)

Sergio Luiz Stevan

2015-10-01

Full Text Available Vegetable oils used in frying food represent a social problem as its destination. The residual oil can be recycled and returned to the production line, as biodiesel, as soap, or as putty. The state of the residual oil is determined according to their physicochemical characteristics whose values define its economically viable destination. However, the physicochemical analysis requires high costs, time and general cost of transporting. This study presents the use of a capacitive sensor and a quick and inexpensive method to correlate the physicochemical variables to the dielectric constant of the material undergoing oil samples to thermal cycling. The proposed method allows reducing costs in the characterization of residual oil and the reduction in analysis time. In addition, the method allows an assessment of the quality of the vegetable oil during use. The experimental results show the increasing of the dielectric constant with the temperature, which facilitates measurement and classification of the dielectric constant at considerably higher temperatures. The results also confirm a definitive degradation in used oil and a correlation between the dielectric constant of the sample with the results of the physicochemical analysis (iodine value, acid value, viscosity and refractive index.

Sensor and methodology for dielectric analysis of vegetal oils submitted to thermal stress.

Science.gov (United States)

Stevan, Sergio Luiz; Paiter, Leandro; Galvão, José Ricardo; Roque, Daniely Vieira; Chaves, Eduardo Sidinei

2015-10-16

Vegetable oils used in frying food represent a social problem as its destination. The residual oil can be recycled and returned to the production line, as biodiesel, as soap, or as putty. The state of the residual oil is determined according to their physicochemical characteristics whose values define its economically viable destination. However, the physicochemical analysis requires high costs, time and general cost of transporting. This study presents the use of a capacitive sensor and a quick and inexpensive method to correlate the physicochemical variables to the dielectric constant of the material undergoing oil samples to thermal cycling. The proposed method allows reducing costs in the characterization of residual oil and the reduction in analysis time. In addition, the method allows an assessment of the quality of the vegetable oil during use. The experimental results show the increasing of the dielectric constant with the temperature, which facilitates measurement and classification of the dielectric constant at considerably higher temperatures. The results also confirm a definitive degradation in used oil and a correlation between the dielectric constant of the sample with the results of the physicochemical analysis (iodine value, acid value, viscosity and refractive index).

Kolkhoung (Pistacia khinjuk) Hull Oil and Kernel Oil as Antioxidative Vegetable Oils with High Oxidative Stability 
and Nutritional Value.

Science.gov (United States)

Asnaashari, Maryam; Hashemi, Seyed Mohammad Bagher; Mehr, Hamed Mahdavian; Yousefabad, Seyed Hossein Asadi

2015-03-01

In this study, in order to introduce natural antioxidative vegetable oil in food industry, the kolkhoung hull oil and kernel oil were extracted. To evaluate their antioxidant efficiency, gas chromatography analysis of the composition of kolkhoung hull and kernel oil fatty acids and high-performance liquid chromatography analysis of tocopherols were done. Also, the oxidative stability of the oil was considered based on the peroxide value and anisidine value during heating at 100, 110 and 120 °C. Gas chromatography analysis showed that oleic acid was the major fatty acid of both types of oil (hull and kernel) and based on a low content of saturated fatty acids, high content of monounsaturated fatty acids, and the ratio of ω-6 and ω-3 polyunsaturated fatty acids, they were nutritionally well--balanced. Moreover, both hull and kernel oil showed high oxidative stability during heating, which can be attributed to high content of tocotrienols. Based on the results, kolkhoung hull oil acted slightly better than its kernel oil. However, both of them can be added to oxidation-sensitive oils to improve their shelf life.

Fatty Acid Digestibility in Lactating Cows Fed Increasing Amounts of Protected Vegetable Oil, Fish Oil or Saturated Fat

DEFF Research Database (Denmark)

Børsting, Christian Friis; Weisbjerg, Martin Riis; Hvelplund, Torben

1992-01-01

Fatty acid digestion was studied in three dairy cows cannulated in the rumen, duodenum and ileum. Cows were fed encapsulated fat sources (vegetable oil, saturated fat and fish oil). A preperiod diet was fed with no added fat. In a graeco-latin design nine diets comprising three levels of each...... of the three fat sources were fed. The preperiod diet contained 230 g fatty acids (FA), whereas the three other fats were fed at about 550, 850 and 1150 g FA/day. The feed-ileùm true digestibility of total FA was 95, 47 and 86% for vegetable, saturated and fish fat, respectively. The true digestibility of FA...

Rapid bioassay-guided screening of toxic substances in vegetable oils that shorten the life of SHRSP rats

Directory of Open Access Journals (Sweden)

Lewandowski Paul

2010-02-01

Full Text Available Abstract It has been consistently reported that vegetable oils including canola oil have a life shortening effect in Stroke-Prone Spontaneously Hypertensive Rats (SHRSP and this toxic effect is not due to the fatty acid composition of the oil. Although it is possible that the phytosterol content or type of phytosterol present in vegetable oils may play some role in the life shortening effect observed in SHRSP rats this is still not completely resolved. Furthermore supercritical CO2 fractionation of canola oil with subsequent testing in SHRSP rats identified safe and toxic fractions however, the compounds responsible for life shortening effect were not characterised. The conventional approach to screen toxic substances in oils using rats takes more than six months and involves large number of animals. In this article we describe how rapid bioassay-guided screening could be used to identify toxic substances derived from vegetable oils and/or processed foods fortified with vegetable oils. The technique incorporates sequential fractionation of oils/processed foods and subsequent treatment of human cell lines that can be used in place of animal studies to determine cytotoxicity of the fractions with structural elucidation of compounds of interest determined via HPLC-MS and GC-MS. The rapid bioassay-guided screening proposed would require two weeks to test multiple fractions from oils, compared with six months if animal experiments were used to screen toxic effects. Fractionation of oil before bio-assay enhances the effectiveness of the detection of active compounds as fractionation increases the relative concentration of minor components.

Emissions from diesel engines using fatty acid methyl esters from different vegetable oils as blends and pure fuel

International Nuclear Information System (INIS)

Schröder, O; Munack, A; Schaak, J; Pabst, C; Schmidt, L; Bünger, J; Krahl, J

2012-01-01

Biodiesel is used as a neat fuel as well as in blends with mineral diesel fuel. Because of the limited availability of fossil resources, an increase of biogenic compounds in fuels is desired. To achieve this goal, next to rapeseed oil, other sustainably produced vegetable oils can be used as raw materials. These raw materials influence the fuel properties as well as the emissions. To investigate the environmental impact of the exhaust gas, it is necessary to determine regulated and non-regulated exhaust gas components. In detail, emissions of aldehydes and polycyclic aromatic hydrocarbons (PAH), as well as mutagenicity in the Ames test are of special interest. In this paper emission measurements on a Euro III engine OM 906 of Mercedes-Benz are presented. As fuel vegetable oil methyl esters from various sources and reference diesel fuel were used as well as blends of the vegetable oil methyl esters with diesel fuel. PAH were sampled according to VDI Guideline 3872. The sampling procedure of carbonyls was accomplished using DNPH cartridges coupled with potassium iodide cartridges. The carbon monoxide and hydrocarbon emissions of the tested methyl esters show advantages over DF. The particle mass emissions of methyl esters were likewise lower than those of DF, only linseed oil methyl ester showed higher particle mass emissions. A disadvantage is the use of biodiesel with respect to emissions of nitrogen oxides. They increased depending on the type of methyl ester by 10% to 30%. Emissions of polycyclic aromatic hydrocarbons (PAHs) and the results of mutagenicity tests correlate with those of the PM measurements, at which for palm oil methyl ester next to coconut oil methyl ester the lowest emissions were detected. From these results one can formulate a clear link between the iodine number of the ester and the emission behaviour. For blends of biodiesel and diesel fuel, emissions changed linearly with the proportion of biodiesel. However, especially in the non

Responses of selected biota after biostimulation of a vegetable oil ...

African Journals Online (AJOL)

Responses of selected biota after biostimulation of a vegetable oil spill in the Con Joubert Bird Sanctuary wetland: A pilot study. Mapurunyane C Selala, Paul J Oberholster, Karen AK Surridge, Arno R de Klerk, Anna-Maria Botha ...

[Determination of gossypol in edible vegetable oil with high performance liquid chromatography-tandem mass spectrometry].

Science.gov (United States)

Zhang, Wenhua; Huang, Chaoqun; Xie, Wen; Shen, Li

2014-06-01

A liquid chromatography-tandem mass spectrometry (LC-MS/MS) method was developed for the determination of gossypol in edible vegetable oil. The sample was extracted with ethyl alcohol by vortex-excited oscillation. The extract was cleaned up by 0.22 microm filter membrane and centrifuged for 5 min at 4 000 r/min after standing in a fridge at 4 degrees C for 30 min. The compound was separated on a C18 column (100 mm x 2.1 mm, 3.5 microm) with acetonitrile and 1% (v/v) formic acid aqueous solution as mobile phase. The detection of gossypol was carried out by LC-MS/MS with positive electrospray ionization under multiple reaction monitoring (MRM) mode using external standard method. The limits of quantification (S/N > 10) of gossypol in edible vegetable oil was 1 mg/kg. The recoveries were from 87.4% to 100% at the spiked levels of 1, 2, 200 mg/kg of gossypol in edible vegetable oil with the relative standard deviations (RSDs) between 3.9% and 12.2%. The method, with high sensitivity, good precision and high recovery, was suitable for the confirmation and quantification of gossypol residue in edible vegetable oil.

Effect of Vegetable Oils on the Surface Tension, Diffusion and Efficiency of Sethoxydim to Control Wild oat (Avena ludoviciana Durieu.

Directory of Open Access Journals (Sweden)

H. Hammami

2017-08-01

Full Text Available Introduction: During last century, population explosion has been pressing man to produce more supplies of food by consuming more energy in agroecosystems like applying chemical management strategies. herbicides have increasingly become a key component of weed management programs. In Iran, using herbicides led to increasing wheat yield about 20% and 22% in rainfed and irrigated farms respectively (20. Nonetheless, herbicides have also a negative impact on environment. A tool for reducing the herbicide usage which allows to decreasing their cost and side effects is the use of adjuvants. They increase the effectiveness of the post-emergence herbicides. Some adjuvants have toxic effects on living organisms such as Polyethoxylated tallowamine adjuvants that they are very toxic in fairy shrimp (Thamnocephalus platyurus (6. Vegetable oils are not phytotoxic and likely are degraded and metabolized quickly in the environment (8. Sethoxydim is an acetyl coenzyme A carboxylase (ACCase inhibitor that is considered to be a key enzyme in lipid biosynthesis. Similar to other foliar applied herbicides, it need to be associated with an adjuvant for more effective control. Vegetable oils can be developed characteristics of sethoxydim solution such as surface tension and spry drop diffusion. Therefore, the objective of this research is to determine the effect of vegetable oils on the surface tension, diffusion and efficiency of sethoxydim to control wild oat (Avena ludoviciana Durieu.. Materials and Metods: To evaluate the effect of vegetable oils on properties of sethoxydim solution, a series of experiments were separately conducted at Ferdowsi University of Mashhad and Khorasan Science and Technology Park in 2012. For evaluating the effect of vegetable oils on surface tension of distilled water and sethoxydim solution and the sethoxydim efficiency on wild oat control, three experiments were conducted as factorial based on completely randomized design. In other

Unilever food safety assurance system for refined vegetable oils and fats

Directory of Open Access Journals (Sweden)

van Duijn Gerrit

2010-03-01

Full Text Available The Unilever Food Safety Assurance system for refined oils and fats is based on risk assessments for the presence of contaminants or pesticide residues in crude oils, and refining process studies to validate the removal of these components. Crude oil risk assessments were carried out by combining supply chain visits, and analyses of the contaminant and pesticide residue levels in a large number of crude oil samples. Contaminants like poly-aromatic hydrocarbons and hydrocarbons of mineral origin, and pesticide residues can largely be removed by refining. For many years, this Food Safety Assurance System has proven to be effective in controlling contaminant levels in refined vegetable oils and fats.

Formation of alkanes alkylcycloalkanes and alkylbenzenes during the catalytic hydrocracking of vegetable oils

Energy Technology Data Exchange (ETDEWEB)

Filho, G.N. da Rocha; Brodzki, D.; Djega-Mariadassou, G. (Universite Pierre et Marie Curie, Paris (France). Lab. Reactivite de Surface et Structure)

1993-04-01

Catalytic hydrocracking of vegetable oils was performed in the presence of a NiMo/[gamma]-Al[sub 2]O[sub 3] catalyst sulfided in situ with elemental sulfur under hydrogen pressure. Various vegetable oils were selected to study the effect of the degree of saturation and lateral chain length: [ital Passiflora edulis] (maracuja), [ital Astrocaryum vulgare] (tucuma), [ital Mauritia flexuosa] (buriti), [ital Orbygnya martiana] (babassu) and soybean. The effects of reaction temperature and hydrogen pressure in cyclization were studied. Carboxylic acids were used as model compounds. 29 refs., 5 figs., 5 tabs.

Vegetable Oil-Loaded Nanocapsules: Innovative Alternative for Incorporating Drugs for Parenteral Administration.

Science.gov (United States)

Venturinil, C G; Bruinsmann, A; Oliveira, C P; Contri, R V; Pohlmann, A R; Guterres, S S

2016-02-01

An innovative nanocapsule formulation for parenteral administration using selected vegetable oils (mango, jojoba, pequi, oat, annatto, calendula, and chamomile) was developed that has the potential to encapsulate various drugs. The vegetable oil-loaded nanocapsules were prepared by interfacial deposition and compared with capric/caprylic triglyceride-loaded lipid core nanocapsules. The major objective was to investigate the effect of vegetable oils on particle size distribution and physical stability and to determine the hemolytic potential of the nanocapsules, considering their applicability for intravenous administration. Taking into account the importance of accurately determining particle size for the selected route of administration, different size characterization techniques were employed, such as Laser Diffraction, Dynamic Light Scattering, Multiple Light Scattering, Nanoparticle Tracking Analysis, and Transmission Electronic Microscopy. Laser diffraction studies indicated that the mean particle size of all nanocapsules was below 300 nm. For smaller particles, the laser diffraction and multiple light scattering data were in agreement (D[3,2]-130 nm). Dynamic light scattering and nanoparticle tracking analysis, two powerful techniques that complement each other, exhibited size values between 180 and 259 nm for all nanoparticles. Stability studies demonstrated a tendency of particle creaming for jojoba-nanocapsules and sedimentation for the other nanoparticles; however, no size variation occurred over 30 days. The hemolysis test proved the hemocompatibility of all nanosystems, irrespective of the type of oil. Although all developed nanocapsules presented the potential for parenteral administration, jojoba oil-loaded nanocapsules were selected as the most promising nanoformulation due to their low average size and high particle size homogeneity.

A catalogue of crude oil and oil product properties, 1990

International Nuclear Information System (INIS)

Bobra, M.A.; Callaghan, S.

1990-09-01

This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 109 refs

A catalogue of crude oil and oil product properties, 1992

International Nuclear Information System (INIS)

Whiticar, S.; Bobra, M.; Liuzzo, P.; Callaghan, S.; Fingas, M.; Jokuty, P.; Ackerman, F.; Cao, J.

1993-02-01

This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 140 refs

Lipids for Health and Beauty: Enzymatic Modification of Vegetable Oil

Science.gov (United States)

Ferulic acid has been extensively investigated for its potential as a cosmetic and pharmaceutical agent. We have prepared lipophilic derivatives of ferulic acid by a simple, enzyme-catalyzed transesterification reaction of ethyl ferulate with vegetable oils. Immobilized Candida antarctica lipase B...

[Effects of vegetal oil supplementation on the lipid profile of Wistar rats ].

Science.gov (United States)

Poveda, Elpidia; Ayala, Paola; Milena, Rodríguez; Ordóñez, Edgar; Baracaldo, Cesar; Delgado, Willman; Guerra, Martha

2005-03-01

Dietary tocopherols, tocotrienols and saturated, mono and polyunsaturated fatty acids have been reported to have an effect on blood lipid profiles. In Colombia, vegetable oils (palm, soy, corn, sunflower, and canola) are a common dietary constituent and consumed in high quantities. In the current study, the effects of vegetable oil consumption was examined by measuring blood concentrations of triglycerides (TG), total cholesterol (TC) and HDL cholesterol (HDL-C) in male Wistar rats. The concentrations of tocopherols, tocotrienols, and fatty acids in each oil was quantified by High Performance Liquid Chromatography (HPLC). Each rat diet was supplemented with 0.2 ml/day with one oil type. Over a 4-week period, groups of animals were sacrificed weekly and blood samples were obtained to quantify TC, TG and HDL-C for each oil class. Statistical analyses included mean, standard deviation, ANOVA and Bonferroni comparisons tests. Triglyceride content was not affected except in the control and the soy group in the third treatment week, although a tendency for decreased TG was noted in the palm oil group and for increased TG in the sunflower oil and canola oil groups. No significant differences in total cholesterol were observed. In HDL-C, significant differences were present for every treatment week (p = 0.005); this represented a decreasing trend in palm oil group and an increasing trend in the sunflower and corn oil groups. The oils effected changes in the blood lipid profile. A small amount of saturated fatty acids (tocopherol and tocotrienol) were favourable for the HDL-C increase. The presenct of tocorienols tended to decrease the TG and probably helped attenuate the unfavorable effects of the saturated fatty acids.

Breads Fortified with Freeze-Dried Vegetables: Quality and Nutritional Attributes. Part 1: Breads Containing Oil as an Ingredient

Directory of Open Access Journals (Sweden)

Viren Ranawana

2016-03-01

Full Text Available There is increasing emphasis on reformulating processed foods to make them healthier. This study for the first time comprehensively investigated the effects of fortifying bread (containing oil as an ingredient with freeze-dried vegetables on its nutritional and physico-chemical attributes. Breads fortified with carrot, tomato, beetroot or broccoli were assessed for nutrition, antioxidant potential, storage life, shelf stability, textural changes and macronutrient oxidation. Furthermore, using an in vitro model the study for the first time examined the impact of vegetable addition on the oxidative stability of macronutrients during human gastro-intestinal digestion. As expected, adding vegetables improved the nutritional and antioxidant properties of bread. Beetroot and broccoli significantly improved bread storage life. None of the vegetables significantly affected bread textural changes during storage compared to the control. Lipid oxidation in fresh bread was significantly reduced by all four types of vegetables whilst protein oxidation was lowered by beetroot, carrot and broccoli. The vegetables demonstrated varying effects on macronutrient oxidation during gastro-intestinal digestion. Beetroot consistently showed positive effects suggesting its addition to bread could be particularly beneficial.

Physicochemical properties and oxidative stability of bleached pomace-olive oil on Tunisian activated clays

International Nuclear Information System (INIS)

Jahouach, Wafa

2002-01-01

This work is a contribution to studying bleaching process, which is an important stage in refining of vegetable oils. This process permitted to reduce or convert undesired constituents to harmless ones from oils and fats. Virgin olive oil, considered as reference, and pomace-olive oil were bleached in optimal conditions using Tunisian activated clays ( collected from the South of Tunisia) which were prepared in our laboratory and compared with commercial bleaching earths. It was shown that activated Tunisian clays are characterized by a very important adsorptive capacity, which is similar to that of commercial ones. In addition, the study of physicochemical properties of bleached oils was considered. The fatty acid composition (GC), the triacylglycerol composition (HPLC), and oxidative stability (UV spectrometry) allowed to conclude that treated oils do not undergo considerable physicochemical alterations and their caracteristics remain in concordance with international standards relative to edible refined oils. (Author)

Comparison of chemical characteristics of high oleic acid fraction of moringa oleifera oil with some vegetable oils

International Nuclear Information System (INIS)

Rahman, F.; Nadeem, M.; Zahoor, Y.

2014-01-01

Chemical characteristics of High oleic acid fraction (HOF) of Moringa oleifera oil (MOO) was compared with sunflower, soybean and canola oils. HOF of MOO was obtained by dry fractionation at 0 degree C. Iodine value and C18:1 in HOF increased from 61.55 to 82.47 points and 70.29% to 81.15%, respectively. Cloud point of HOF was 1.1 degree C as compared to 10.2 degree C in MOO. The induction period of HOF was greater than all the vegetable oils tested in this investigation. HOF can be used as a source of edible oil with better health attributes and superior storage stability. (author)

The use of antioxidants in vegetable oils – A review

African Journals Online (AJOL)

STORAGESEVER

2008-12-29

Dec 29, 2008 ... Department of Chemical Engineering, University of Benin, Benin City, Nigeria. Accepted 12 ... Methods of improving oxidative stability values currently available include ... Key words: Vegetable oils, oxidative stability, natural extracts. .... the development of oxidative rancidity has been applied in the US ...

Novel Bioplastics and biocomposites from Vegetable Oils

Energy Technology Data Exchange (ETDEWEB)

Henna, Phillip H. [Iowa State Univ., Ames, IA (United States)

2008-01-01

there are three degrees of unsaturation. In addition, the double bonds are not in conjugation. Table 1 gives the fatty acid make-up of linseed oil. It can be seen that linseed oil has an average of 6.0 double bonds per triglyceride. Its fatty acid content consists of 5.4% palmitic acid (C16:0), 3.5% stearic acid (C18:0), 19% oleic acid (C18:1), 24 % linoleic acid (C18:2) and 47% linolenic (C18:3). Table 1 also gives the fatty acid composition and varying degrees of unsaturation for various other naturally-occurring natural vegetable oils. The regions of unsaturation in natural oils allow for interesting polymer chemistry to take place. Some of this interesting polymer science, however, involves chemical modification of the regions of unsaturation. Acrylated epoxidized soybean oil (AESO) is prepared by epoxidation of the double bonds, followed by ring opening with acrylic acid. The resulting oil has both acrylate groups and hydroxyl groups. Wool and colleagues have further reacted the hydroxyl groups within the oil with maleic anhydride to produce maleated acrylated epoxidized soybean oil (MAESO). The MAESO has been copolymerized with styrene free radically to produce promising thermosetting sheet molding resins. Petrovi? and co-workers have directly ring opened the epoxidized oil to produce polyols that produce promising polyurethanes through condensation polymerization with diisocyanates. Our group's work initially focused on direct cationic copolymerization of the double bonds or conjugated double bonds of natural oils with monomers, such as styrene and divinylbenzene, to produce promising thermosetting resins. The only modification of the oils that was carried out in these studies was conjugation of the double bonds to enhance the reactivity of the oil. This work has been expanded recently with the incorporation of glass fiber to produce promising composites. We have also explored thermal polymerization techniques to make novel thermosets. This dissertation is

Reduced Need of Lubricity Additives in Soybean Oil Blends Under Boundary Lubrication Conditions

Science.gov (United States)

Converging prices of vegetable oils and petroleum, along with increased focus on renewable resources, gave more momentum to vegetable oil lubricants. Boundary lubrication properties of four Extreme Pressure (EP) additive blends in conventional Soy Bean Oil (SBO) and Paraffinic Mineral Oil (PMO) of ...

Evaluation of the use of a vegetable oil in distribution transformers

OpenAIRE

Fernando-Navas,Diego; Echeverry-Ibarra,Diego Fernando; Cadavid-Ramírez,Héctor

2012-01-01

Since the start of transformers immersed in refrigerating liquid, the fluid traditionally used has been mineral oil. However, in recent decades, efforts have been joined in the search for alternatives with a lower environmental impact and which also satisfy the technical requirements of insulation and refrigeration in the transformers. Currently, insulating vegetable oils are available in the market, which may have lower environmental impact during their use and final disposition; nevertheles...

Performance evaluation of NEEM oil and HONGE Oil as cutting fluid in drilling operation of mild steel

Science.gov (United States)

Jyothi, P. N.; Susmitha, M.; Sharan, P.

2017-04-01

Cutting fluids are used in machining industries for improving tool life, reducing work piece and thermal deformation, improving surface finish and flushing away chips from the cutting zone. Although the application of cutting fluids increases the tool life and Machining efficiency, but it has many major problems related to environmental impacts and health hazards along with recycling & disposal. These problems gave provision for the introduction of mineral, vegetable and animal oils. These oils play an important role in improving various machining properties, including corrosion protection, lubricity, antibacterial protection, even emulsibility and chemical stability. Compared to mineral oils, vegetable oils in general possess high viscosity index, high flash point, high lubricity and low evaporative losses. Vegetable oils can be edible or non-edible oils and Various researchers have proved that edible vegetable oils viz., palm oil, coconut oil, canola oil, soya bean oil can be effectively used as eco-friendly cutting fluid in machining operations. But in present situations harnessing edible oils for lubricants formation restricts the use due to increased demands of growing population worldwide and availability. In the present work, Non-edible vegetable oil like Neem and Honge are been used as cutting fluid for drilling of Mild steel and its effect on cutting temperature, hardness and surface roughness are been investigated. Results obtained are compared with SAE 20W40 (petroleum based cutting fluid)and dry cutting condition.

A systematic framework for CAFD and resources allocation optimisation using MINLP in vegetable oil processing

DEFF Research Database (Denmark)

Quaglia, Alberto; Sarup, Bent; Sin, Gürkan

Although being a mature and well established industry segment, over the last few decades the vegetable oil industry has been facing many important new challenges due to emerging new products (such as biodiesel and nutraceuticals compounds), as well as new trends and regulations with regards....... In this paper, a systematic framework for Computer-Aided Flowsheet Syntesis and Design (CAFD) and resources allocation for the vegetable oil sector is presented. In the framework a Mixed Integer Non Linear Programming (MINLP) problem is formulated and solved for a soybean processing case study, to determine...... the optimal processing network for vegetable oil extraction and refining (including biodiesel production and various options for byproducts valorization), as well as the optimal material flows to each processing step. In order to optimize the resources needed to solve such a large and complex problem...

Performance evaluation of vegetable-based oils in drilling austenitic stainless steel

DEFF Research Database (Denmark)

Belluco, Walter; De Chiffre, Leonardo

2004-01-01

breaking were recorded for each bore, and tool wear was measured at constant intervals. A commercial mineral-based oil was taken as reference product, and five vegetable-based cutting fluids at different levels of additivation were tested. All measured parameters were in agreement, confirming......The efficiency of six cutting oils was evaluated in drilling AISI 316L austenitic stainless steel using conventional HSS-Co tools by measurements of tool life, tool wear, cutting forces and chip formation. Seven tools were tested with each fluid to catastrophic failure. Cutting forces and chip...... to tool life testing. All vegetable-based fluids performed better than the reference product. The best performance was obtained with a cutting fluid yielding 177% increases in tool life and 7% reduction in thrust force. (C) 2003 Elsevier B.V. All rights reserved....

Performances of cutting fluids in turning. Vegetable based oil - RV

DEFF Research Database (Denmark)

Axinte, Dragos Aurelian; Belluco, Walter

1999-01-01

Scope of the present measurement campaign is the evaluation of the cutting fluid performance. The report presents the standard routine and the results obtained when turning stainless steel and brass with a commercial vegetable based oil called RV. The methods were developed to be applicable...

Comparative Studies on Some Physicochemical Properties of ...

African Journals Online (AJOL)

Keywords: Physicochemical properties, vegetable Oils, Baobab. INTRODUCTION. Fat and .... vegetable oil (0.32), though a disadvantage in the paint and soap industry may ... inferior to other edible oils used for cooking. It is safe for human ...

Detection of argan oil adulteration with vegetable oils by high-performance liquid chromatography-evaporative light scattering detection.

Science.gov (United States)

Salghi, Rachid; Armbruster, Wolfgang; Schwack, Wolfgang

2014-06-15

Triacylglycerol profiles were selected as indicator of adulteration of argan oils to carry out a rapid screening of samples for the evaluation of authenticity. Triacylglycerols were separated by high-performance liquid chromatography-evaporative light scattering detection. Different peak area ratios were defined to sensitively detect adulteration of argan oil with vegetable oils such as sunflower, soy bean, and olive oil up to the level of 5%. Based on four reference argan oils, mean limits of detection and quantitation were calculated to approximately 0.4% and 1.3%, respectively. Additionally, 19 more argan oil reference samples were analysed by high-performance liquid chromatography-refractive index detection, resulting in highly comparative results. The overall strategy demonstrated a good applicability in practise, and hence a high potential to be transferred to routine laboratories. Copyright © 2013 Elsevier Ltd. All rights reserved.

COMPARISON OF THE QUALITY OF VEGETABLE OILS DESIGNED FOR THE FRYING FOOD

Directory of Open Access Journals (Sweden)

Ladislav Mura

2012-12-01

Full Text Available The object of the research was to investigate the quality of vegetable oils for cooking food. The analysis used two types of oils - oil Fritol and Promienna. Both oils were purchased commercially. Oil changes were observed at frying French fries. At the same changes were observed oil stored at room temperature and the temperature in the refrigerator. The determined parameters included the measurement of polar materials in oil with electronic device Testo 265 for measuring the quality of cooking oil. Determination of change in the texture of oil during the oil deterioration by device Texturometer TA.XT Plus and determination the peroxide value by STN EN ISO 3960:2007. The work is also evaluating the results of the studied parameters. In all compared cases based on the content of the TPM showed higher heat resistance oil Fritol and sample of oil stored in the refrigerator.doi:10.5219/210

Solubility of Two Vegetable Oils in Supercritical CO2

Czech Academy of Sciences Publication Activity Database

Sovová, Helena; Zarevúcka, Marie; Vacek, Miroslav; Stránský, Karel

2001-01-01

Roč. 20, č. 1 (2001), s. 15-28 ISSN 0896-8446 R&D Projects: GA ČR GA203/99/1457; GA ČR GA203/98/1445 Institutional research plan: CEZ:AV0Z4072921 Keywords : vegetable oil * supercritical CO2 * solubility Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.975, year: 2001

PERFORMANCE AND EMISSION CHARACTERISTICS OF A CI ENGINE OPERATED ON VEGETABLE OILS AS ALTERNATIVE FUELS

Directory of Open Access Journals (Sweden)

K. Rajagopal

2011-12-01

Full Text Available An experimental analysis was done using a four-stroke, single cylinder, constant speed, water-cooled diesel engine, which was interfaced with Engine software. Performance and emission characteristics were evaluated for three non-edible vegetable oils, i.e. thumba, jojoba, neem oil, as well as jojoba methyl ester, to study the effect of injection pressure at 205, 220, 240 and 260 bar with a variation in injection timing at 23°bTDC and 28°bTDC. The performance of jojoba methyl ester improved with an increase in injection pressure. A maximum brake thermal efficiency of 29.72% was obtained with lower emissions compared to the other vegetable oils; this might be explained by low viscosity and better combustion. Further investigations were carried out with a new lubricant, SAE 5W-30, which improved the performance of the CI engine by 1.59%. All of the abovementioned investigations were fruitful and these results are expected to lead to substantial contributions in the development of a viable vegetable oil engine.

Retention levels of vegetable extractable beta-carotene preserved in virgin coconut oil and unadulterated honey

Directory of Open Access Journals (Sweden)

Mungai, Z. M.,

2017-06-01

Full Text Available Dark green leafy vegetables such as Amaranthus spp. are known to be good sources of beta-carotene, a pro-vitamin A carotenoid with highly potent antioxidant property. As an antioxidant, beta-carotene scavenges for electron and thus terminates chain reactions, prevents recurrence and formation of unstable oxygen which otherwise initiate a chain reaction leading to such cases as cancer. While beta-carotene is supplied from consuming vegetables to provide vitamin A, it is also given as a supplement in cases of deficiency. However, it is highly degraded in the presence of light, heat, and oxygen posing a challenge to the methods of its preservation. Coconut oil and honey are popularly consumed in many countries facing vitamin A deficiency as good antioxidants and yet their role in preservation is largely unknown. The study reports the retention of beta-carotene extracted from Amaranthus spp. and separately preserved in virgin coconut oil (VCO and unadulterated honey for up to six months. HPLC and DPPH assay were used to determine beta-carotene and antioxidant activity respectively. Virgin coconut oil and honey had significantly different (p<0.001 antioxidant activities of 65.12±0.70 and 81.51±1.39 % radical scavenging activity respectively that compared well with those of BHT and ascorbic acid. The concentration of beta-carotene preserved in VCO and unadulterated honey degraded by 90%, though the final retention provided higher than the recommended daily allowance of retinol (0.216±0.001 and 0.312±0.003 retinol activity equivalent respectively when 100 mg is consumed. Virgin coconut oil and unadulterated honey can preserve beta-carotene if high amounts are used.

Optimization of Jatropha curcas pure vegetable oil production parameters for cooking energy

Directory of Open Access Journals (Sweden)

X. Aboubakar

2017-12-01

Full Text Available The extraction of vegetable oil from Jatropha from the Tanzanian variety with a fat content of 33.84 ± 2.58% and a moisture content of 5.4 ± 1.97%, was made using two methods: the traditional and the mechanical extraction method. The traditional consists in extracting the oil from the paste using boiling water as a solvent. While the mechanical consists of directly pressing the seeds of Jatropha using a ram press called Bielenberg press, to extract the oil contained in the seeds dried or heated before. The net yield of oil extraction by the traditional method was 22.02 ± 2.1%, with a oil cake percentage of 67.02 ± 3.3% and the ratio water/paste in mass adopted was 0.36. Mechanical extraction has an average raw yield of 26.15 ± 2.74%, with a recovery rate of 74.71%. After decanting for 10 days and filtration, the net yield was 15.39 ± 2.82% with a decantation and filtration rate of 58.67 ± 7.24%. The oil produced by traditional method has a water and volatile content of 1.01 ± 0.05% and a density of 0.884. The one produced by mechanical extraction has 0.19 ± 0.09% and a density of 0.891. The result of combustion test using two burners and one stove showed that the combustion rates were: 0.177 ± 0.034 g/min for the burner using one flame and 1.06 ± 0.04 g/min for the six flame burner and finally 3.07 ± 0, 4 g/min for the ten-flame stove. This ten-flame stove allowed 3 L of water to be boiled at 100 °C for 32 min, although during combustion it was observed a release of black fumes which indicates incomplete combustion with Jatropha in this Stove. The cost of the liter of Jatropha oil obtained is higher compared to fossil fuels such as petroleum (500 FCFA per liter and gas oil (624F CFA per liter. It would be possible to use vegetable oil from Jatropha as a cooking fuel. Keywords: Vegetable oil, Jatropha, Traditional extraction, Mechanical extraction, Bielenberg press

Effect of methanol extracts of rosemary and olive vegetable water on the stability of olive oil and sunflower oil

Directory of Open Access Journals (Sweden)

Gamel, T. H.

1999-10-01

Full Text Available Effect of methanol extracts of rosemary and olive vegetable water on the stability of olive oil and sunflower oil. Methanol phenolic extracts of dry rosemary leaves and olive vegetable water filtrate, in combination with BHA, were added to olive oil (blend of refined and virgin olive oil, 3 to 1 and to sunflower oil and their antioxidant effects under accelerated conditions were evaluated. Accelerated conditions included the oven test (at 63 °C and the conductivity method (Rancimat at 120 °C. Frying process at 180 °C was also applied. The methanol phenolic extracts and the BHA were added to each oil at the following concentrations: 200 ppm rosemary extract; 200 ppm olive vegetable water extract; 100 ppm rosemary extract + 100 ppm BHA; 100 ppm vegetable water extract + 100 ppm BHA and 200 ppm BHA. In general, antioxidant effect of phenolic additives of rosemary and of BHA was in the following order: 200 ppm rosemary extract > 100 ppm rosemary extract + 100 ppm BHA > and 200 ppm BHA. The addition of 200 ppm vegetable water extract and 100 ppm vegetable water extract + 100 ppm BHA exhibited similar antioxidant effect to that of 200 ppm BHA.

Extractos metanólicos de fenoles de hojas secas de romero y filtrados de agua de vegetación de la aceituna, en combinación con BHA, se añadieron al aceite de oliva (mezcla de aceite de oliva refinado y virgen, 3 a 1 y al aceite de girasol, evaluándose sus efectos antioxidantes usando condiciones aceleradas. Estas condiciones incluyeron el test del horno de oxidación (a 63 °C y el método de conductividad (Rancimat a 120 °C. También se aplicó al proceso de fritura a 180 °C. Los extractos metanólicos de fenoles y el BHA se añadieron a cada aceite en las siguientes concentraciones: 200 ppm de extracto de romero, 200 ppm de extracto de agua de vegetación de la aceituna, 100 ppm de extracto de romero + 100 ppm de BHA, 100 ppm de extracto de agua de vegetación + 100 ppm de BHA y 200 ppm de BHA

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

OpenAIRE

Li Benkai; Li Changhe; Zhang Yanbin; Wang Yaogang; Jia Dongzhou; Yang Min

2016-01-01

Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type t...

The relation between dietary intake of vegetable oils and serum lipids and apolipoprotein levels in central Iran

Directory of Open Access Journals (Sweden)

Hossein Khosravi Boroujeni

2012-01-01

Full Text Available BACKGROUND: The detrimental effects of partially hydrogenated vegetable oils (PHVOs on apolipoproteins have been reported from several parts of the world. However, little data is available in this regard from the understudied region of the Middle East. The present study therefore tried to evaluate the association between type of vegetable oils and serum lipids and apolipoprotein levels among Iranians. METHODS: In this cross-sectional study, data from 1772 people (795 men and 977 women aged 19-81 years, who were selected with multistage cluster random sampling method from three cities of Isfahan, Najaf Abad and Arak in "Isfahan Healthy Heart Program" (IHHP, was used. To assess participants' usual dietary intakes, a validated food frequency questionnaire was used. Hydrogenated vegetable oil (commonly consumed for cooking in Iran and margarine were considered as the category of PHVOs. Soy, sunflower, corn, olive and canola oils were considered as non-HVOs. After an overnight fasting, serum cholesterol (total, low density lipoprotein (LDL and high density lipoprotein (HDL cholesterol and triglyceride as well as apolipoproteins A and B were measured using standard methods. RESULTS: Participants with the highest intakes of non-HVOs and PHVOs were younger and had lower weight than those with lowest intakes. High consumption of non-HVOs and PHVOs was associated with lower intakes of energy, carbohydrate, dietary fiber, and higher intakes of fruits, vegetables, meat, milk and grains. No overall significant differences were found in serum lipids and apolipoprotein levels across the quartiles of non-HVOs and PHVOs after controlling for potential confounding. CONCLUSION: We did not find any significant associations between hydrogenated or non-hydrogenated vegetable oil and serum lipid and apolipoprotein levels. Thus, further studies are needed in this region to explore this association. Keywords: Vegetable Oils, Cardiovascular Risk Factors, Lipids

Rheology of oleogels based on sorbitan and glyceryl monostearates and vegetable oils for lubricating applications

Directory of Open Access Journals (Sweden)

Sánchez, R.

2011-09-01

Full Text Available Oleogels based on sorbitan and glyceryl monostearates and different types of vegetable oils, potentially applicable as biodegradable alternatives to traditional lubricating greases, have been studied. In particular, the rheological behavior, by means of small-amplitude oscillatory shear (SAOS measurements, and some lubrication performance-related properties (mechanical stability and tribological response have been evaluated in this work. SAOS response and mechanical stability of these oleogels are significantly influenced by the type and concentration of the organogelator and the vegetable oil used in the formulations. Glyceryl monostearate (GMS generally produces stronger gels than sorbitan monostearate (SMS. The use of low-viscosity oils, such as rapeseed and soybean oils, yields gels with significantly higher values of the linear viscoelastic functions than oleogels prepared with high-viscosity oils, i.e. castor oil. The rheological behavior of SMS-based oleogels also depends on the cooling rate applied during the gelification process. On the other hand, the oleogels studied present low values of the friction coefficient obtained in a tribological contact, although only some GMS/castor oil-based oleogels exhibit a suitable mechanical stability.

En el presente trabajo se han estudiado diferentes oleogeles, basados en monoestearatos de sorbitano y glicerilo y aceites vegetales, que podrían ser potencialmente empleados como alternativas biodegradables a las grasas lubricantes tradicionales. En concreto, se ha evaluado su comportamiento reológico, a través de ensayos en cizalla oscilatoria, y algunas propiedades relacionadas con su rendimiento en la lubricación, tales como su estabilidad mecánica y comportamiento tribológico. La respuesta reológica y la estabilidad mecánica de los oleogeles estudiados están significativamente influenciadas por el tipo y la concentración del agente gelificante y por el aceite vegetal empleado. As

Development of continuous processes for vegetable oil alcoholysis in microfluidic devices

Directory of Open Access Journals (Sweden)

Richard Romain

2013-01-01

Full Text Available Biodiesel can be produced from vegetable oils, animal fats, and waste cooking oils by transesterification with ethanol (also called ethanolysis in order to substitute fossil fuels. In this work, we were interested in the transesterification reaction of sunflower oil with ethanol, which leads to ethyl esters, used to date for applications principally in food and cosmetic industry. To open the application field to biofuels (to substitute current fuels resulting from fossil resources, the process efficiency has to be developed to be economically profitable. The batch reaction of vegetable oil ethanolysis was transposed to a micro-scaled continuous device (PFA tube of 508 μm internal diameter, inducing better heat and mass transfer. Study of the influence of the operational conditions (reactants flow, initial ethanol to oil molar ratio, temperature. . . revealed the favourable reaction parameters necessary to reach high conversions and yields. In these conditions, it is possible to acquire kinetics data at the first seconds of the reaction, which was not feasible in a conventional batch process. These data were used to model occurring phenomena and to determine kinetic constants and transfer coefficients. The model was subsequently used to simulate reactions with other operational conditions. To acquire these data in microreactors, an on-line analysis method by Near InfraRed (NIR spectroscopy was developed by using gas chromatography as a reference method. PLS models were then set up to quantify on-line the major compounds contents during the reaction.

Soybean-oil-based waterborne polyurethane dispersions: effects of polyol functionality and hard segment content on properties.

Science.gov (United States)

Lu, Yongshang; Larock, Richard C

2008-11-01

The environmentally friendly vegetable-oil-based waterborne polyurethane dispersions with very promising properties have been successfully synthesized without difficulty from a series of methoxylated soybean oil polyols (MSOLs) with different hydroxyl functionalities ranging from 2.4 to as high as 4.0. The resulting soybean-oil-based waterborne polyurethane (SPU) dispersions exhibit a uniform particle size, which increases from about 12 to 130 nm diameter with an increase in the OH functionality of the MSOL from 2.4 to 4.0 and decreases with increasing content of the hard segments. The structure and thermophysical and mechanical properties of the resulting SPU films, which contain 50-60 wt % MSOL as renewable resources, have been studied by Fourier transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, thermogravimetric analysis, transmission electron microscopy, and mechanical testing. The experimental results reveal that the functionality of the MSOLs and the hard segment content play a key role in controlling the structure and the thermophysical and mechanical properties of the SPU films. These novel films exhibit tensile stress-strain behavior ranging from elastomeric polymers to rigid plastics and possess Young's moduli ranging from 8 to 720 MPa, ultimate tensile strengths ranging from 4.2 to 21.5 MPa, and percent elongation at break values ranging from 16 to 280%. This work has addressed concerns regarding gelation and higher cross-linking caused by the high functionality of vegetable-oil-based polyols. This article reports novel environmentally friendly biobased SPU materials with promising applications as decorative and protective coatings.

Chemical and spectroscopic characterization of a vegetable oil used as dielectric coolant in distribution transformers

Energy Technology Data Exchange (ETDEWEB)

Gomez, Neffer A.; Abonia, Rodrigo, E-mail: rodrigo.abonia@correounivalle.edu.co [Departamento de Quimica, Escuela de Ingenieria Electrica, Universidad del Valle, Cali (Colombia); Cadavid, Hector [Grupo GRALTA, Escuela de Ingenieria Electrica, Universidad del Valle, Cali (Colombia); Vargas, Ines H. [Area de Ingenieria de Distribucion, Empresas Publicas de Medellin (EPM), Medellin (Colombia)

2011-09-15

In this work, a complete UV-Vis, IR and (1H, 13C and DEPT) NMR spectroscopic analysis was performed for a FR3 vegetable oil sample used as dielectric coolant in an experimental distribution transformer. The same spectroscopic analysis was performed for three used FR3 oil samples (i.e., 4 months in use, 8 months in use and 7 years in use), removed from several operating distribution transformers. Comparison of the data indicated that no significant spectroscopic changes, and hence, no structural changes occurred to the oils by the use. Chemical transformations like catalytic hydrogenation (hardening) and hydrolysis were performed to the FR3 oil sample and the obtained products were analyzed by spectroscopic methods in order to collect further structural information about the FR3 oil. Accelerated aging tests in laboratory were also performed for three FR3 oil samples affording interesting information about the structure of the degradation products. These findings would be valuable to search for a spectroscopy-based technique for monitoring the lifetime and performance of this insulating vegetable oil. (author)

Modification of olefinic double bonds of unsaturated fatty acids and other vegetable oil derivatives via epoxidation: A review

International Nuclear Information System (INIS)

Noor Armylisas, A.H.; Siti Hazirah, M.F.; Yeong, S.K.; Hazimah, A.H.

2017-01-01

The highly strained ring in epoxides makes these compounds very versatile intermediates. Epoxidized vegetable oils are gaining a lot of attention as renewable and environmentally friendly feedstock with various industrial applications such as plasticizers, lubricant base oils, surfactants, etc. Numerous papers have been published on the development of the epoxidation methods and the number is still growing. This review reports the synthetic approaches and applications of epoxidized vegetable oils. [es

Study of the oxidative stability of oils vegetables for production of Biodiesel

Directory of Open Access Journals (Sweden)

Marco Aurélio R Melo

2014-04-01

Full Text Available Biodiesel is technological and estrategical Brazilian oportunity once this country has abundant vegetable species which oils are extracted to produce this biofuel. Oleaginous viability depends on its technical, economical and social-environmental competitiviness. Fatty acid variety determines its thermal and oxidative stability, mainly polyunsaturated ones. In this point of view, this papers aims evaluate oxidative stability and resistence to thermal decomposition of pequi, buriti and macauba oils. These fatty acids profiles are in agreement with literature data. Comparing thermal and oxidative stability of these oils, it can be seen pequi oil is more easily to oxidate than buriti and macauba oils when PetroOXY and Rancimat methods are employed.

Is it true that polymerization of vegetable oil occurs through Diels-Alder reaction?

Science.gov (United States)

Diels-Alder reaction mechanism is known to be one of the major reaction mechanisms to produce dimers and polymers during heating process of vegetable oil. However, our NMR study showed no evidence for Diels-Alder products. Soybean oil oxidized at 180 °C for 24 hrs with 1.45 surface area-to-volume ...

Evaluation of Palm Oil as a Suitable Vegetable Oil for Vitamin A Fortification Programs.

Science.gov (United States)

Pignitter, Marc; Hernler, Natalie; Zaunschirm, Mathias; Kienesberger, Julia; Somoza, Mark Manuel; Kraemer, Klaus; Somoza, Veronika

2016-06-21

Fortification programs are considered to be an effective strategy to mitigate vitamin A deficiency in populations at risk. Fortified vegetable oils rich in polyunsaturated fatty acids were shown to be prone to oxidation, leading to limited vitamin A stability. Thus, it was hypothesized that fortified oils consisting of mainly saturated fatty acids might enhance the stability of vitamin A. Mildly (peroxide value: 1.0 meq O₂/kg) and highly (peroxide value: 7.5 meq O₂/kg) oxidized palm oil was stored, after fortification with 60 International Units/g retinyl palmitate, in 0.5 L transparent polyethylene terephthalate bottles under cold fluorescent lighting (12 h/day) at 32 °C for 57 days. An increase of the peroxide value by 15 meq O₂/kg, which was also reflected by a decrease of α-tocopherol congener by 15%-18%, was determined independent of the initial rancidity. The oxidative deterioration of the highly oxidized palm oil during storage was correlated with a significant 46% decline of the vitamin A content. However, household storage of mildly oxidized palm oil for two months did not induce any losses of vitamin A. Thus, mildly oxidized palm oil may be recommended for vitamin A fortification programs, when other sources of essential fatty acids are available.

Process Parameters Optimization of Potential SO42-/ZnO Acid Catalyst for Heterogeneous Transesterification of Vegetable Oil to Biodiesel

Directory of Open Access Journals (Sweden)

Istadi Istadi

2012-12-01

Full Text Available Among the possible renewable energy resources, diesel fuels derived from triglycerides of vegetable oils and animal fats have shown potential as substitutes for petroleum-based diesel fuels. The biodiesel could be produced from vegetable oils over homogeneous catalyst, heterogeneous catalyst, or enzymatic catalyst. In this study, the synthesized SO42-/ZnO catalyst was explored to be used in the heterogeneous biodiesel production by using the vegetable oils and methanol. The study began with the preparation of SO42-/ZnO catalyst followed by the transesterification reaction between vegetable oil with methanol. The independent variables (reaction time and the weight ratio of catalyst/oil were optimized to obtain the optimum biodiesel (fatty acid methyl ester yield. The results of this study showed that the acid catalyst SO42-/ZnO was potential to be used as catalyst for biodiesel production through heterogeneous transesterification of vegetable oils. Optimum operating condition for this catalytic reaction was the weight ratio of catalyst/oil of 8:1 and reaction time of 2.6 h with respect to 75.5% yield of methyl ester products. The biodiesel product was also characterized to identify the respected fatty acid methyl ester components. Copyright © 2012 by BCREC UNDIP. All rights reserved. (Selected Paper from International Conference on Chemical and Material Engineering (ICCME 2012Received: 23rd October 2012, Revised: 25th November 2012, Accepted: 25th November 2012[How to Cite: I. Istadi, Didi D. Anggoro, Luqman Buchori, Inshani Utami, Roikhatus Solikhah, (2012. Process Parameters Optimization of Potential SO42-/ZnO Acid Catalyst for Heterogeneous Transesterification of Vegetable Oil to Biodiesel. Bulletin of Chemical Reaction Engineering & Catalysis, 7(2: 150-157. (doi:10.9767/bcrec.7.2.4064.150-157][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.7.2.4064.150-157 ] | View in 

Synthesis of Polyformate Esters of Vegetable Oils: Milkweed, Pennycress, and Soy

Directory of Open Access Journals (Sweden)

Rogers E. Harry-O’kuru

2016-01-01

Full Text Available In a previous study of the characteristics of acyl derivatives of polyhydroxy milkweed oil (PHMWO, it was observed that the densities and viscosities of the respective derivatives decreased with increased chain length of the substituent acyl group. Thus from the polyhydroxy starting material, attenuation in viscosity of the derivatives relative to PHMWO was found in the order: PHMWO ≫ PAcMWE ≫ PBuMWE ≫ PPMWE (2332 : 1733 : 926.2 : 489.4 cSt, resp., at 40°C, where PAcMWE, PBuMWE, and PPMWE were the polyacetyl, polybutyroyl, and polypentanoyl ester derivatives, respectively. In an analogous manner, the densities also decreased as the chain length increased although not as precipitously compared to the viscosity drop. By inference, derivatives of vegetable oils with short chain length substituents on the triglyceride would be attractive in lubricant applications in view of their higher densities and possibly higher viscosity indices. Pursuant to this, we have explored the syntheses of formyl esters of three vegetable oils in order to examine the optimal density, viscosity, and related physical characteristics in relation to their suitability as lubricant candidates. In the absence of ready availability of formic anhydride, we opted to employ the epoxidized vegetable oils as substrates for formyl ester generation using glacial formic acid. The epoxy ring-opening process was smooth but was apparently followed by a simultaneous condensation reaction of the putative α-hydroxy formyl intermediate to yield vicinal diformyl esters from the oxirane. All three polyformyl esters milkweed, soy, and pennycress derivatives exhibited low coefficient of friction and a correspondingly much lower wear scar in the 4-ball antiwear test compared to the longer chain acyl analogues earlier studied.

Synthesis of Polyformate Esters of Vegetable Oils: Milkweed, Pennycress, and Soy.

Science.gov (United States)

Harry-O'kuru, Rogers E; Biresaw, Girma; Tisserat, Brent; Evangelista, Roque

2016-01-01

In a previous study of the characteristics of acyl derivatives of polyhydroxy milkweed oil (PHMWO), it was observed that the densities and viscosities of the respective derivatives decreased with increased chain length of the substituent acyl group. Thus from the polyhydroxy starting material, attenuation in viscosity of the derivatives relative to PHMWO was found in the order: PHMWO ≫ PAcMWE ≫ PBuMWE ≫ PPMWE (2332 : 1733 : 926.2 : 489.4 cSt, resp., at 40°C), where PAcMWE, PBuMWE, and PPMWE were the polyacetyl, polybutyroyl, and polypentanoyl ester derivatives, respectively. In an analogous manner, the densities also decreased as the chain length increased although not as precipitously compared to the viscosity drop. By inference, derivatives of vegetable oils with short chain length substituents on the triglyceride would be attractive in lubricant applications in view of their higher densities and possibly higher viscosity indices. Pursuant to this, we have explored the syntheses of formyl esters of three vegetable oils in order to examine the optimal density, viscosity, and related physical characteristics in relation to their suitability as lubricant candidates. In the absence of ready availability of formic anhydride, we opted to employ the epoxidized vegetable oils as substrates for formyl ester generation using glacial formic acid. The epoxy ring-opening process was smooth but was apparently followed by a simultaneous condensation reaction of the putative α-hydroxy formyl intermediate to yield vicinal diformyl esters from the oxirane. All three polyformyl esters milkweed, soy, and pennycress derivatives exhibited low coefficient of friction and a correspondingly much lower wear scar in the 4-ball antiwear test compared to the longer chain acyl analogues earlier studied.

Stability of traditionally processed vegetable oils and their blends ...

African Journals Online (AJOL)

The objective of the study was to investigate the stability of traditionally processed palm oil (PO), sunflower oil (SO) and sesame oil (SSO) and their blends as function of storage conditions by analysing their physicochemical properties which included acid value, saponification value, peroxide value, iodine value and ...

Use of crude filtered vegetable oil as a fuel in diesel engines state of the art: Literature review

Energy Technology Data Exchange (ETDEWEB)

Sidibe, S.S.; Azoumah, Y. [Institut Internationale d' ingenierie de l' Eau et de l' Environnement (2iE), rue de science 01 Ouagadougou 01 BP 594 (Burkina Faso); Blin, J. [Institut Internationale d' ingenierie de l' Eau et de l' Environnement (2iE), rue de science 01 Ouagadougou 01 BP 594 (Burkina Faso); Centre International de Recherche Agronomique pour le Developpement (CIRAD), UPR Biomasse energie, TA B-42/16, 73 rue JF Breton, 34398 Montpellier Cedex 5 (France); Vaitilingom, G. [Centre International de Recherche Agronomique pour le Developpement (CIRAD), UPR Biomasse energie, TA B-42/16, 73 rue JF Breton, 34398 Montpellier Cedex 5 (France)

2010-12-15

Many studies have been published on vegetable oil use in diesel engines. The different authors unanimously acknowledge the potential and merits of this renewable fuel. Typically, Straight Vegetable Oils (SVOs) produced locally on a small scale, have proven to be easy to produce with very little environmental impact. However, as their physico-chemical characteristics differ from those of diesel oil, their use in diesel engines can lead to a certain number of technical problems over time. In bibliography, there is substantial disagreement between authors regarding the advanced phenomena linked to this problems and the recommended solutions. Some of these publications treat options individually without any real comparison between them. Another observation is that the literature rarely tackles problems linked to vegetable oil quality. This paper sets out to review the state of the art for SVO use as fuel in diesel engines, based on a bibliographic study (literature review). The first section of the document examines the influence of the type and quality of vegetable oils for fuel use in diesel engines. The second section discusses the advantages and disadvantages of two options recommended for SVO use in diesel engines: dual fuelling and blending with diesel fuel. (author)

Comparative study of oxidation in canned foods with a combination of vegetables and covering oils

Directory of Open Access Journals (Sweden)

E. Bravi

2015-06-01

Full Text Available The effects of sunflower (SFO, extra-virgin olive (EVO, and soybean oils (SBO, in combination with canned aubergins and dried tomatoes were studied during an accelerated shelf-life trial. Hydrolytic and oxidative quality parameters was determined and a sensorial test was run. For both canned vegetables, the SBO showed greater resistance to the oxidation at the end of the shelflife trial. The SBO in both vegetables yielded similar results for peroxide formation, whereas a reduced formation of secondary oxidation products was observed in aubergins. The results highlighted a higher oxidation stability of canned vegetables in SBO and EVO than those in SFO. The sensorial test underlined differences between the oils, in aubergins and dried tomatoes, after 30 days of accelerated storage (corresponding to the sell-by date. Flavour and texture were judged better for vegetables in SBO.

Differentiation of frog fats from vegetable and marine oils by Fourier Transform Infrared Spectroscopy and chemometric analysis

Directory of Open Access Journals (Sweden)

A. N. Nina Naquiah

2015-01-01

Full Text Available The agro-based production and consumption of frogs coupled with world-wide trading have been increased in the recent years giving rise to the risk of frog fat adulteration in expensive vegetable and marine oils. For the first time, we profiled here frog fats using Fourier Transform Infrared (FTIR Spectroscopy coupled with multivariate principal component analysis (PCA. The comparison of the FTIR spectral absorbance intensities demonstrated linkage of frog fats to other edible fats and oils. Three commercially available marine oils and three vegetables oils were studied with frog fats and clear pattern of clusters with distinctive identifiable features were obtained through PCA modeling. PCA analysis identified 2922.21 cm-1, 2852.88 cm-1, 1745.45 cm-1, 1158.29 cm-1 and 721.51 cm-1 FTIR-frequencies as the most discriminating variables influencing the group separation into different clusters. This fundamental study has clear implications in the identification of frog fat from its marine and vegetable counterparts for the potential detection of frog fat adulteration in various fat and oils.

Technical aspects of biodiesel production from vegetable oils

OpenAIRE

Krishnakumar Janahiraman; Venkatachalapathy Karuppannan V.S.; Elancheliyan Sellappan

2008-01-01

Biodiesel, a promising substitute as an alternative fuel has gained significant attention due to the finite nature of fossil energy sources and does not produce sulfur oxides and minimize the soot particulate in comparison with the existing one from petroleum diesel. The utilization of liquid fuels such as biodiesel produced from vegetable oil by transesterification process represents one of the most promising options for the use of conventional fossil fuels. In the first step of this experim...

Lipid recovery from a vegetable oil emulsion using microbial enrichment cultures

NARCIS (Netherlands)

Tamis, J.; Sorokin, D.Y.; Jiang, Y.; Van Loosdrecht, M.C.M.; Kleerebezem, R.

2015-01-01

Background Many waste streams have a relatively high vegetable oil content, which is a potential resource that should be recovered. Microbial storage compound production for the recovery of lipids from lipid-water emulsions with open (unsterilized) microbial cultures was investigated in a sequencing

Zinc availability in relation to selected soil properties in a crude oil polluted eutric tropofluvent

International Nuclear Information System (INIS)

Chukwuma, M.C.; Eshett, E.T.; Onweremadu, E.U.; Okon, M.A.

2010-01-01

This study examined zinc availability in crude oil-polluted soils. The aim of the study was to determine the effect of zinc on the physiochemical properties of soils in relation to remediation activities. The study was located at a site in Nigeria where crude oil spillage had occurred over a period of 2 months. The region was characterized by quarternary, alluvium, meander belt, wooded back swamps as well as fresh water swamps and Sombreiro-Warri Deltaic plains with large deposits of petroleum and natural gas. Three different land units were studied, notably (1) unpolluted, (2) polluted without vegetation and (3) polluted with vegetation. Soil sampling was conducted using a transect method. Hydrometer analyses were conducted to determine particle size distribution, while a core method was used to determine bulk density. Soil pH, total carbon, phosphorus, and total nitrogen were also measured. An analysis of variance (ANOVA) was used to correlate and regress zinc availability against the selected soil properties. The study showed that zinc availability increased with increases in the value of the effective carbon cation exchange capacity in the unpolluted and polluted samples without vegetation. Zinc decreased with increased clay and organic matter content. Results suggested that soils must be reclaimed quickly in order to prevent additional degradation. 48 refs., 5 tabs., 4 figs.

Zinc availability in relation to selected soil properties in a crude oil polluted eutric tropofluvent

Energy Technology Data Exchange (ETDEWEB)

Chukwuma, M.C.; Eshett, E.T.; Onweremadu, E.U.; Okon, M.A. [Federal Univ. of Technology, Owerri (Nigeria). Dept. of Soil Science and Technology

2010-04-01

This study examined zinc availability in crude oil-polluted soils. The aim of the study was to determine the effect of zinc on the physiochemical properties of soils in relation to remediation activities. The study was located at a site in Nigeria where crude oil spillage had occurred over a period of 2 months. The region was characterized by quarternary, alluvium, meander belt, wooded back swamps as well as fresh water swamps and Sombreiro-Warri Deltaic plains with large deposits of petroleum and natural gas. Three different land units were studied, notably (1) unpolluted, (2) polluted without vegetation and (3) polluted with vegetation. Soil sampling was conducted using a transect method. Hydrometer analyses were conducted to determine particle size distribution, while a core method was used to determine bulk density. Soil pH, total carbon, phosphorus, and total nitrogen were also measured. An analysis of variance (ANOVA) was used to correlate and regress zinc availability against the selected soil properties. The study showed that zinc availability increased with increases in the value of the effective carbon cation exchange capacity in the unpolluted and polluted samples without vegetation. Zinc decreased with increased clay and organic matter content. Results suggested that soils must be reclaimed quickly in order to prevent additional degradation. 48 refs., 5 tabs., 4 figs.

Vegetable Oils as Alternative Solvents for Green Oleo-Extraction, Purification and Formulation of Food and Natural Products.

Science.gov (United States)

Yara-Varón, Edinson; Li, Ying; Balcells, Mercè; Canela-Garayoa, Ramon; Fabiano-Tixier, Anne-Sylvie; Chemat, Farid

2017-09-05

Since solvents of petroleum origin are now strictly regulated worldwide, there is a growing demand for using greener, bio-based and renewable solvents for extraction, purification and formulation of natural and food products. The ideal alternative solvents are non-volatile organic compounds (VOCs) that have high dissolving power and flash point, together with low toxicity and less environmental impact. They should be obtained from renewable resources at a reasonable price and be easy to recycle. Based on the principles of Green Chemistry and Green Engineering, vegetable oils could become an ideal alternative solvent to extract compounds for purification, enrichment, or even pollution remediation. This review presents an overview of vegetable oils as solvents enriched with various bioactive compounds from natural resources, as well as the relationship between dissolving power of non-polar and polar bioactive components with the function of fatty acids and/or lipid classes in vegetable oils, and other minor components. A focus on simulation of solvent-solute interactions and a discussion of polar paradox theory propose a mechanism explaining the phenomena of dissolving polar and non-polar bioactive components in vegetable oils as green solvents with variable polarity.

Estimating the impact of vitamin A-fortified vegetable oil in Bangladesh in the absence of dietary assessment data.

Science.gov (United States)

Fiedler, John L; Lividini, Keith; Bermudez, Odilia I

2015-02-01

Vitamin A deficiency is a serious health problem in Bangladesh. The 2011-12 Bangladesh Micronutrient Survey found 76·8% of children of pre-school age were vitamin A deficient. In the absence of nationally representative, individual dietary assessment data, we use an alternative--household income and expenditure survey data--to estimate the potential impact of the introduction of vitamin A-fortified vegetable oil in Bangladesh. Items in the household income and expenditure survey were matched to food composition tables to estimate households' usual vitamin A intakes. Then, assuming (i) the intra-household distribution of food is in direct proportion to household members' share of the household's total adult male consumption equivalents, (ii) all vegetable oil that is made from other-than mustard seed and that is purchased is fortifiable and (iii) oil fortification standards are implemented, we modelled the additional vitamin A intake due to the new fortification initiative. Nationwide in Bangladesh. A weighted sample of 12,240 households comprised of 55,580 individuals. Ninety-nine per cent of the Bangladesh population consumes vegetable oil. The quantities consumed are sufficiently large and, varying little by socio-economic status, are able to provide an important, large-scale impact. At full implementation, vegetable oil fortification will reduce the number of persons with inadequate vitamin A intake from 115 million to 86 million and decrease the prevalence of inadequate vitamin A intake from 80% to 60%. Vegetable oil is an ideal fortification vehicle in Bangladesh. Its fortification with vitamin A is an important public health intervention.

Effect of vegetable oils applied over acquired enamel pellicle on initial erosion

Directory of Open Access Journals (Sweden)

Franciny Querobim IONTA

Full Text Available Abstract Objective The prevalence of dental erosion has been recently increasing, requiring new preventive and therapeutic approaches. Vegetable oils have been studied in preventive dentistry because they come from a natural, edible, low-cost, and worldwide accessible source. This study aimed to evaluate the protective effect of different vegetable oils, applied in two concentrations, on initial enamel erosion. Material and Methods Initially, the acquired pellicle was formed in situ for 2 hours. Subsequently, the enamel blocks were treated in vitro according to the study group (n=12/per group: GP5 and GP100 – 5% and pure palm oil, respectively; GC5 and GC100 – 5% and pure coconut oil; GSa5 and GSa100 – 5% and pure safflower oil; GSu5 and GSu100 – 5% and pure sunflower oil; GO5 and GO100 – 5% and pure olive oil; CON− – Deionized Water (negative control and CON+ – Commercial Mouthwash (Elmex® Erosion Protection Dental Rinse, GABA/positive control. Then, the enamel blocks were immersed in artificial saliva for 2 minutes and subjected to short-term acid exposure in 0.5% citric acid, pH 2.4, for 30 seconds, to promote enamel surface softening. The response variable was the percentage of surface hardness loss [((SHi - SHf / SHf ×100]. Data were analyzed by one-way ANOVA and Tukey’s test (p0.05 and less than the other groups (p<0.05. There was no difference between GP5, GC5, GC100, GSa5, GSu100, GSa100, GSu5, GO5, GO100, CON− and CON+. Conclusion Palm oil seems to be a promising alternative for preventing enamel erosion. However, further studies are necessary to evaluate a long-term erosive cycling.

Effect of vegetable oils applied over acquired enamel pellicle on initial erosion

Science.gov (United States)

IONTA, Franciny Querobim; de ALENCAR, Catarina Ribeiro Barros; VAL, Poliana Pacifico; BOTEON, Ana Paula; JORDÃO, Maisa Camillo; HONÓRIO, Heitor Marques; BUZALAF, Marília Afonso Rabelo; RIOS, Daniela

2017-01-01

Abstract Objective The prevalence of dental erosion has been recently increasing, requiring new preventive and therapeutic approaches. Vegetable oils have been studied in preventive dentistry because they come from a natural, edible, low-cost, and worldwide accessible source. This study aimed to evaluate the protective effect of different vegetable oils, applied in two concentrations, on initial enamel erosion. Material and Methods Initially, the acquired pellicle was formed in situ for 2 hours. Subsequently, the enamel blocks were treated in vitro according to the study group (n=12/per group): GP5 and GP100 – 5% and pure palm oil, respectively; GC5 and GC100 – 5% and pure coconut oil; GSa5 and GSa100 – 5% and pure safflower oil; GSu5 and GSu100 – 5% and pure sunflower oil; GO5 and GO100 – 5% and pure olive oil; CON− – Deionized Water (negative control) and CON+ – Commercial Mouthwash (Elmex® Erosion Protection Dental Rinse, GABA/positive control). Then, the enamel blocks were immersed in artificial saliva for 2 minutes and subjected to short-term acid exposure in 0.5% citric acid, pH 2.4, for 30 seconds, to promote enamel surface softening. The response variable was the percentage of surface hardness loss [((SHi - SHf) / SHf )×100]. Data were analyzed by one-way ANOVA and Tukey’s test (p0.05) and less than the other groups (p<0.05). There was no difference between GP5, GC5, GC100, GSa5, GSu100, GSa100, GSu5, GO5, GO100, CON− and CON+. Conclusion Palm oil seems to be a promising alternative for preventing enamel erosion. However, further studies are necessary to evaluate a long-term erosive cycling. PMID:28877281

Surface integrity and part accuracy in reaming and tapping stainless steel with new vegetable based cutting oils

DEFF Research Database (Denmark)

Belluco, Walter; De Chiffre, Leonardo

2002-01-01

This paper presents an investigation on the effect of new formulations of vegetable oils on surface integrity and part accuracy in reaming and tapping operations with AISI 316L stainless steel. Surface integrity was assessed with measurements of roughness, microhardness, and using metallographic...... as part accuracy. Cutting fluids based on vegetable oils showed comparable or better performance than mineral oils. ÆÉ2002 Published by Elsevier Science Ltd....... techniques, while part accuracy was measured on a coordinate measuring machine. A widely diffused commercial mineral oil was used as reference for all measurements. Cutting fluid was found to have a significant effect on surface integrity and thickness of the strain hardened layer in the sub-surface, as well...

Fortification of Indonesian unbranded vegetable oil: public-private initiative, from pilot to large scale.

Science.gov (United States)

Soekirman; Soekarjo, Damayanti; Martianto, Drajat; Laillou, Arnaud; Moench-Pfanner, Regina

2012-12-01

Despite improved economic conditions, vitamin A deficiency remains a public health problem in Indonesia. This paper aims to describe the development of the Indonesian unbranded cooking oil fortification program and to discuss lessons learned to date and future steps necessary for implementation of mandatory, large-scale oil fortification with vitamin A. An historic overview of the steps involved in developing the Indonesian unbranded cooking oil fortification program is given, followed by a discussion of lessons learned and next steps needed. Indonesia's low-income groups generally consume unbranded vegetable oil, with an average consumption of approximately 25 g/day. Unbranded oil constitutes approximately 70% of the total oil traded in the country. In 2007-10, a pilot project to fortify unbranded vegetable oil was carried out in Makassar, and an effectiveness study found that the project significantly improved the serum retinol concentrations of schoolchildren. In 2010, the pilot was expanded to two provinces (West Java and North Sumatra) involving the biggest two national refineries. In 2011, a draft national standard for fortified oil was developed, which is currently under review by the National Standard Body and is expected to be mandated nationally in 2013 as announced officially by the Government of Indonesia in national and international meetings. Indonesia is a leading world supplier of cooking oil. With stakeholder support, the groundwork has been laid and efforts are moving forward to implement mandatory fortification. This project could encourage Indonesian industry to fortify more edible oils for export, thus expanding their market potential and potentially reducing vitamin A deficiency in the region.

Incorporating different vegetable oils into an aqueous dispersion of hybrid organic nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Samyn, Pieter, E-mail: Pieter.Samyn@fobawi.uni-freiburg.de [Albert-Luedwigs-University Freiburg, Institute for Forest Utilization (Germany); Schoukens, Gustaaf [Ghent University, Department of Textiles (Belgium); Stanssens, Dirk; Vonck, Leo; Van den Abbeele, Henk [Topchim N.V. (Belgium)

2012-08-15

Different vegetable oils including soy oil, high-oleic sunflower oil, corn oil, castor oil (CO), rapeseed oil, and hydrogenated CO were added to the imidization reaction of poly(styrene-maleic anhydride) or SMA, with ammonium hydroxide in aqueous medium. The oils favorably reduce viscosity during ammonolysis of the anhydride moieties and increase the maximum solid content of the dispersed imidized SMA to at least 50 wt%, compared to a maximum of 35 wt% for pure imidized SMA. The viscosity of imidized SMA with polyunsaturated oils was generally larger than for monosaturated oils, but it was highest for COs due to high contents of hydroxyl groups. Depending on the oil reactivity, homogeneous or core-shell nanoparticles with 20-60 nm diameters formed. The interactions of oil and organic phase were studied by Fourier-transform infrared spectroscopy, indicating qualitative variances between different oils, the fraction imidized SMA and remaining fraction of ammonolyzed SMA without leakage of oil upon diluting the dispersion and precipitation at low pH. A quantitative analysis with calculation of imide contents, amounts of reacted oil and chemical interactions was made by Fourier-transform-Raman spectroscopy suggesting that most interactions take place around the unsaturated oil moieties and ammonolyzed anhydride.

Antioxidant Effect on Oxidation Stability of Blend Fish Oil Biodiesel with Vegetable Oil Biodiesel and Petroleum Diesel Fuel

Directory of Open Access Journals (Sweden)

M. Hossain

2013-06-01

Full Text Available Two different phenolic synthetic antioxidants were used to improve the oxidation stability of fish oil biodiesel blends with vegetable oil biodiesel and petroleum diesel. Butylhydroxytoluene (BHT most effective for improvement of the oxidation stability of petro diesel, whereas  tert-butylhydroquinone (TBHQ showed good performance in fish oil biodiesel. Fish oil/Rapeseed oil biodiesel mixed showed some acceptable results in higher concentration ofantioxidants. TBHQ showed better oxidation stability than BHT in B100 composition. In fish oil biodiesel/diesel mixed fuel, BHT was more effective antioxidant than TBHQ to increase oxidationstability because BHT is more soluble than TBHQ. The stability behavior of biodiesel/diesel blends with the employment of the modified Rancimat method (EN 15751. The performance ofantioxidants was evaluated for treating fish oil biodiesel/Rapeseed oil biodiesel for B100, and blends with two type diesel fuel (deep sulfurization diesel and automotive ultra-low sulfur or zero sulfur diesels. The examined blends were in proportions of 5, 10, 15, and 20% by volume of fish oilbiodiesel.

Utilization of immobilized lipases as catalysts in the transesterification of non-edible vegetable oils with ethanol

Directory of Open Access Journals (Sweden)

P. C. Tiosso

2014-12-01

Full Text Available This work reports the use of commercially available immobilized lipase preparations (Novozym® 435 and Lipozyme TL IM, both from Novozymes, and Lipase PS IM from Amano as catalysts in the transesterification reaction of different alkyl-chain triglycerides with ethanol. The ethanolysis of native oils from Brazilian Amazon plants andiroba (Carapa guianensis, babassu (Orbignya sp., jatropa (Jatropha curcas, and palm (Elaeis sp. was studied in a solvent-free system. In a typical reaction, the immobilized preparations were added to the mixture of vegetable oil-to-ethanol in a molar ratio of 1:9. The reactions were performed at 50 ºC for a maximum period of 48 h. Under the conditions used, all the immobilized lipase preparations were able to generate the main esters of fatty acids present in the tested feedstocks, and both the reaction rate and ester yield were dependent on the source of lipase and vegetable oil. The viscosity values for the samples obtained in each reaction displayed a consistent reduction in relation to their original feedstocks, which also confirms the high conversion of triglycerides to ethyl esters (99.8-74.0%. The best performances were obtained with Amano PS IM and Novozym® 435, with the biodiesel samples from the babassu and jatropha oils exhibiting viscosity values in accordance with those predicted by the technical standards of ASTM D6751 (1.9-6.0 mm²/s. Lipozyme TL IM displayed an unsatisfactory performance, indicating that the conditions of the transesterification reaction should be improved. This comparative study using different catalysts and several vegetable oil sources with varying fatty acid compositions is particularly important for all tropical countries with a diversity of native vegetable oil sources.

Fourier transform infrared and fluorescence spectroscopy for analysis of vegetable oils

Directory of Open Access Journals (Sweden)

Nigri S.

2013-09-01

Full Text Available Fourier transform infrared (FTIR and fluorescence spectroscopy, combined with chemometric approaches have been developed to analysis of extra virgin olive oil adulterated with pomace olive oil. The measurements were made on pure vegetable oils: extra virgin oil, pomace olive oil and that adulterated with varying concentration of pomace olive oil. Today, the application of FTIR spectroscopy has increased in food studied, and particularly has become a powerful analytical tool in the study of edible oils and fats. The spectral regions where the variations were observed chosen for developing models and cross validation was used. The synchronous fluorescence spectrometry takes advantage of the hardware capability to vary both the excitation and emission wavelengths during the analysis with constant wavelength difference is maintained between the two. The region between 300 and 400 nm is attributed to the tocopherols and phenols, the derivatives of vitamin E are associated with the region 400–600 nm and the bands in the region of 600–700 nm are attributed to the chlorophyll and peophytin pigments. The results presented in this study suggest that FTIR and fluorescence may be a useful tool for analysis and detecting adulteration of extra virgin olive oil with pomace oil.

Nutritional enrichment of vegetable oils with long-chain n-3 fatty acids through enzymatic interesterification with a new vegetable lipase

Directory of Open Access Journals (Sweden)

Sousa, J. S.

2015-06-01

Full Text Available The aim of the present work was to produce vegetable oils enriched with long-chain n-3 fatty acids of nutraceutical interest, through an enzyme-catalyzed interesterification with a new lipase, from physic nut (Jatropha curcas L.. The Vegetable Lipase Powder (biocatalyst called VLP, which has never been applied in functional foods, was obtained from the physic nut seed, and efficiently hydrolyzed the 95% of waste fish oil in 24 h. Urea precipitation was used to concentrate polyunsaturated fatty acids (PUFA and was further interesterified with oils of different sources by means of enzymatic catalysis. After the interesterification reaction, which was also catalyzed by the VLP, the PUFA content in coconut oil increased almost ten-fold from 1.8% to 17.7%. In palm oil, the PUFA content increased two-fold from 10.5% to 21.8%, while in olive oil the level of PUFA increased from 8.6% to 21.3%. The mixture of eicosapentaenoic acid (EPA and docosahexaenoic acid (DHA (3.7% to 3.9% was incorporated into the triacylglycerol fraction of each of the coconut, palm and olive oils. Through the hydroesterification (hydrolysis followed by interesterification all the interesterified vegetable oils tested presented sufficient EPA and DHA levels to satisfy the levels recommended for intake by human adults in one tablespoon.El objetivo del presente trabajo fue producir aceites vegetales enriquecidos con ácidos grasos n-3 de cadena larga de interés nutraceutico, por interesterificación catalizada mediante una nueva lipasa, una enzima de semilla de Jatropha curcas L. La lipasa vegetal en polvo (biocatalizador llamada VLP, nunca ha sido aplicada en alimentos funcionales, se obtuvo mediante procedimientos físicos con semillas de nueces, e hidrolizó eficientemente el 95% de aceites de residuos de pescado en 24 h. La precipitación con urea se utilizó para concentrar los ácidos grasos poliinsaturados (PUFA que fueron posteriormente interesterificados con aceites de

Combined effects of thermal barrier coating and blending with diesel fuel on usability of vegetable oils in diesel engines

International Nuclear Information System (INIS)

Aydin, Hüseyin

2013-01-01

The possibility of using pure vegetable oils in a thermally insulated diesel engine has been experimentally investigated. Initially, the standard diesel fuel was tested in the engine, as base experiment for comparison. Then the engine was thermally insulated by coating some parts of it, such as piston, exhaust and intake valves surfaces with zirconium oxide (ZrO 2 ). The main purpose of engine coating was to reduce heat rejection from the walls of combustion chamber and to increase thermal efficiency and thus to increase performance of the engine that using vegetable oil blends. Another aim of the study was to improve the usability of pure vegetable oils in diesel engines without performing any fuel treatments such as pyrolysis, emulsification and transesterification. Pure inedible cottonseed oil and sunflower oil were blended with diesel fuel. Blends and diesel fuel were then tested in the coated diesel engine. Experimental results proved that the main purpose of this study was achieved as the engine performance parameters such as power and torque were increased with simultaneous decrease in fuel consumption (bsfc). Furthermore, exhaust emission parameters such as CO, HC, and Smoke opacity were decreased. Also, sunflower oil blends presented better performance and emission parameters than cottonseed oil blends. -- Highlights: ► Usability of two different vegetable oils in a coated diesel engine was experimentally investigated. ► A diesel engine was coated with ZrO 2 layer to make the combustion chamber insulated. ► Test results showed significant improvements in performance parameters. ► While only minor reductions were observed in emissions with coated engine operation

COMPARISON OF BIODIESEL PRODUCTIVITIES OF DIFFERENT VEGETABLE OILS BY ACIDIC CATALYSIS

Directory of Open Access Journals (Sweden)

AYTEN SAGIROGLU

2011-03-01

Full Text Available Biodiesel has become a subject which increasingly attracts worldwide attention because of its environmental benefits, biodegradability and renewability. Biodiesel production typically involves the transesterification of a triglyceride feedstock with methanol or other short-chain alcohols. This paper presents a study of transesterification of various vegetable oils, sunflower, safflower, canola, soybean, olive, corn, hazelnut and waste sunflower oils, with the acidic catalyst. Under laboratory conditions, fatty acid methyl esters (FAME were prepared by using methanol in the presence of 1.85% hydrochloric acid at 100 °C for 1 h and 25 °C for 3 h. The analyses of biodiesel were carried out by gas chroma¬tography and thin layer chromatography. Also, biodiesel productivities (% were determined on basis of the ratio of ester to oil content (w/w. The biodiesel productivities for all oils were found to be about 80% and about 90% at 25 and 100 °C, respectively. Also, the results showed that the yield of biodiesel depended on temperature for some oils, including canola, sunflower, safflower oils, but it was not found significant differences among all of the oil types on biodiesel productivities.

Determination of saturated aliphatic hydrocarbons in vegetable oils

Energy Technology Data Exchange (ETDEWEB)

Gomez Coca, R.B.; Cert, R.; Perez Camino, M.C.; Moreda, W.

2016-07-01

The aim of this work is to inform about the development of a simple and reliable off-line method for the determination of saturated hydrocarbons (SH) in vegetable oils. SH can be used as markers for fuel or for mineral oil contamination in edible oils and fats. The method consists of the isolation of the fraction by LC on deactivated silver-silica gel and subsequent on-column GC-FID analysis. This stationary phase was prepared avoiding any kind of activation. The method was developed and validated through the participation in both a proficiency test organized by the Joint Research Centre of the European Commission, and a collaborative trial carried out with trained Spanish laboratories according to the standard ISO 5725. Results showed acceptable repeatability and reproducibility values, and Horrat index, being this protocol in use with satisfactory results ever since. The method’s LOQ is 15 mg·kg–1 and its LOD 5 mg·kg–1, which make it suitable to quantify the 50 mg·kg–1 limit established by the EU, and to detect mineral oil content within the 10–500 mg·kg–1 range. Although other procedures with lower LOD have been developed throughout the years, the use of just regular laboratory equipment such as GC-FID makes the proposed method appropriate for application on a routine basis. (Author)

Synthesis and application of molecularly imprinted polymers for the selective extraction of organophosphorus pesticides from vegetable oils.

Science.gov (United States)

Boulanouar, Sara; Combès, Audrey; Mezzache, Sakina; Pichon, Valérie

2017-09-01

The increasing use of pesticides in agriculture causes environmental issues and possible serious health risks to humans and animals. Their determination at trace concentrations in vegetable oils constitutes a significant analytical challenge. Therefore, their analysis often requires both an extraction and a purification step prior to separation with liquid chromatography (LC) and mass spectrometry (MS) detection. This work aimed at developing sorbents that are able to selectively extract from vegetable oil samples several organophosphorus (OPs) pesticides presenting a wide range of physico-chemical properties. Therefore, different conditions were screened to prepare molecularly imprinted polymers (MIPs) by a non-covalent approach. The selectivity of the resulting polymers was evaluated by studying the OPs retention in pure media on both MIPs and non-imprinted polymers (NIP) used as control. The most promising MIP sorbent was obtained using monocrotophos (MCP) as the template, methacrylic acid (MAA) as the monomer and ethylene glycol dimethacrylate (EGDMA) as the cross-linker with a molar ratio of 1/4/20 respectively. The repeatability of the extraction procedure and of the synthesis procedure was demonstrated in pure media. The capacity of this MIP was 1mg/g for malathion. This MIP was also able to selectively extract three OPs from almond oil by applying the optimized SPE procedure. Recoveries were between 73 and 99% with SD values between 4 and 6% in this oil sample. The calculated LOQs (between 0.3 and 2μg/kg) in almond seeds with a SD between 0.1 and 0.4μg/kg were lower than the Maximum Residue Levels (MRLs) established for the corresponding compounds in almond seed. Copyright © 2017 Elsevier B.V. All rights reserved.

Biofuel characteristics of beniseed (Sesanum indicum) oil

African Journals Online (AJOL)

SERVER

2007-11-05

Nov 5, 2007 ... Local method was used to extract oil from beniseed (Sesanum indicum). ... fuel properties similar to common biofuels, hence beniseed could be utilized as an .... industries for the manufacture of soap and vegetable oil –.

A new method to determine oxidative stability of vegetable fats and oils at simulated frying temperature

Directory of Open Access Journals (Sweden)

Gertz Christian

2001-01-01

Full Text Available A new procedure at simulated frying conditions in our laboratory was developed to monitor frying stability of fats and oils. Water-conditioned silica was prepared and added to the fresh vegetable oil, which was heated for two hours at 170°C. The oil stability at frying temperature was then evaluated by determining the amount of formed dimeric triglycerides The results obtained showed that the stability of the vegetable oils at frying temperature could not be explained by the fatty acid composition alone. Corn oil was observed to be more stable than soybean oil, and rapeseed oil was better than olive oil. It was also observed that crude, non-refined oils were found to have a better heat stability than refin-ed oils. To estimate the effectiveness of synthetic and naturally occurring antioxidants, namely various tocopherols, tocopherol acetate and phytosterol fractions, phenolic compounds like quercetin, oryzanol, ferulic acid, gallates, BHT, BHA and other compounds like ascorbic acid 6-palmitate and squalene were added to refined sunflower and rape seed oil, and their oxidative stability at elevated temperature (OSET values determined. Both linoleic and oleic rich oils gave comparable results for the activity of the various compounds. alpha-tocopherol, tocopherol esters and BHA had low effects on oil stability at frying temperature, while ascorbyl palmitate and some phytosterol fractions were found to have the most stabilizing activity under frying conditions.

Coconut oil has less satiating properties than medium chain triglyceride oil.

Science.gov (United States)

Kinsella, R; Maher, T; Clegg, M E

2017-10-01

It is well established that the consumption of medium-chain triglycerides (MCT) can increase satiety and reduce food intake. Many media articles promote the use of coconut oil for weight loss advocating similar health benefits to that of MCT. The aim of this study was to examine the effect of MCT oil compared to coconut oil and control oil on food intake and satiety. Following an overnight fast, participants consumed a test breakfast smoothie containing 205kcal of either (i) MCT oil (ii) coconut oil or (iii) vegetable oil (control) on three separate test days. Participants recorded appetite ratings on visual analogue scales and were presented with an ad libitum lunch meal of preselected sandwiches 180min after consumption of the breakfast. The results showed a significant difference in energy and macronutrient intakes at the ad libitum meal between the three oils with the MCT oil reducing food intake compared to the coconut and control oil. Differences in food intake throughout the day were found for energy and fat, with the control having increased food intake compared to the MCT and coconut. The MCT also increased fullness over the three hours after breakfast compared to the control and coconut oils. The coconut oil was also reported as being less palatable than the MCT oil. The results of this study confirm the differences that exist between MCT and coconut oil such that coconut oil cannot be promoted as having similar effects to MCT oil on food intake and satiety. Crown Copyright © 2017. Published by Elsevier Inc. All rights reserved.

COMPETITIVE POSITION OF THE MAIN PRODUCERS AND EXPORTERS OF OILSEEDS AND VEGETABLE OILS IN THE INTRA-EU TRADE

Directory of Open Access Journals (Sweden)

Karolina Pawlak

2014-09-01

Full Text Available The aim of the paper was to assess the competitive position of the main producers and exporters of oilseeds and vegetable oils in the intra-EU trade in 2004 and 2012. The competitiveness was assessed with the use of a selected set of quantitative measures of international competitive position. Moreover, some shares of the analysed countries in the intra-EU trade, as well as relative export intensity of oilseeds and vegetable oils in these countries were estimated. On the basis of the conducted analyses it is possible to conclude that apart from Germany in trade in rapeseed and soya beans, as well as the Netherlands in trade in rapeseed and sunflower-seed, the main producers and exporters of oilseeds were competitive on the Single European Market. Excluding soya-bean oil produced in the EU mainly from imported raw material, competitive advantage of most of the countries decreased together with the level of processing and was lower in trade in vegetable oils.

Segmentation of the industrial market for food commodities: A conjoint study of purchase of vegetable oils in the mayonnaise and margarine industries

DEFF Research Database (Denmark)

Bech-Larsen, Tino; Skytte, Hans

Executive summary The purpose of this working paper is to study whether current market and technological developments in the vegetable oil industry can be used as the outset for a price and/or quality based segmentation of the major industrial markets for this product. More specifically we want...... that the application of concepts from ind buying behaviour to the study of commodity buying, such as the procurement of vegetable oil, is an appropriate outset, when trying to segment the market for such commodities. The article begins with a brief discussion of why food commodity markets should be segmented......, then follows current developments in the demand and technology conditions on the market for vegetable oil. Later we discuss how concepts from industrial buying behaviour can add to the understanding of commodity buying and segmentati Following this a conjoint model of vegetable oil procurement in the vegetable...

Study Of The Physicochemical Analysis Of Biodiesel Produced From Waste Vegetable Oil.

Directory of Open Access Journals (Sweden)

C. O. Okpanachi

2017-07-01

Full Text Available The study of the physicochemical analysis of biodiesel produced from waste vegetable oil in Sedi Minna Nigeria was carried out in order to ascertain the quality of the biodiesel produced as regards physical and chemical parameters which include visual appearance colour cloud point flash point and cetane index diesel index kinematic velocity calorific value. Biodiesel is a renewable resource that can replace petroleum diesel which comes from fossil fuels that are limited and will be exhausted in the near future. Biodiesel can be made from the transesterification of vegetable oils animal fat greases and oil crops such as soybean and it is biodegradable. The biodiesel produced was subjected to physicochemical analysis and results of cetane index was established to be 52 the flash point using pensky martens close cup was determine to be 1600C diesel index using IP21 0.3411 kinematic viscosity at 400C to be 4.12 and calorific value of 10867calg. The investigated physicochemical parameters show that the biodiesel produced is suitable for use in diesel engines without modifications and is cheaper to produce compared to petroleum diesel.

The effect of oil pulling with pure coconut oil on Streptococcus mutans: A randomized controlled trial

OpenAIRE

Varsha Komath Pavithran; Madhusudhan Krishna; Vinod A Kumar; Ashish Jaiswal; Arul K Selvan; Sudhir Rawlani

2017-01-01

Introduction: Oil pulling as described in ancient Ayurveda involves the use of edible vegetable oils as oral antibacterial agents. It is a practice of swishing oil in the mouth for oral and systemic health benefits. Pure coconut oil has antimicrobial properties and is commonly available in all Indian households. Aim: This study aims to assess the effect of oil pulling therapy with pure coconut oil on Streptococcus mutans count and to compare its efficacy against sesame oil and saline. Materia...

Fish sauce, soy sauce, and vegetable oil fortification in Cambodia: where do we stand to date?

Science.gov (United States)

Theary, Chan; Panagides, Dora; Laillou, Arnaud; Vonthanak, Saphoon; Kanarath, Chheng; Chhorvann, Chhea; Sambath, Pol; Sowath, Sol; Moench-Pfanner, Regina

2013-06-01

The prevalence of micronutrient deficiencies in Cambodia is among the highest in Southeast Asia. Fortification of staple foods and condiments is considered to be one of the most cost-effective strategies for addressing micronutrient deficiencies at the population level. The Government of Cambodia has recognized the importance of food fortification as one strategy for improving the nutrition security of its population. This paper describes efforts under way in Cambodia for the fortification of fish sauce, soy sauce, and vegetable oil. Data were compiled from a stability test of Cambodian fish sauces fortified with sodium iron ethylenediaminetetraacetate (NaFeEDTA); analysis of fortified vegetable oils in the Cambodian market; a Knowledge, Attitudes, and Practices (KAP) study of fortified products; and food fortification program monitoring documents. At different levels of fortification of fish sauce with NaFeEDTA, sedimentation and precipitation were observed. This was taken into consideration in the government-issued standards for the fortification of fish sauce. All major brands of vegetable oil found in markets at the village and provincial levels are imported, and most are nonfortified. Fish sauce, soy sauce, and vegetable oil are widely consumed throughout Cambodia and are readily available in provincial and village markets. Together with an effective regulatory monitoring system, the government can guarantee that these commodities, whether locally produced or imported, are adequately fortified. A communications campaign would be worthwhile, once fortified commodities are available, as the KAP study found that Cambodians had a positive perception of fortified sauces.

Life cycle inventory analysis of hydrogen production by the steam-reforming process: comparison between vegetable oils and fossil fuels as feedstock

International Nuclear Information System (INIS)

Marquevich, M.; Sonnemann, G.W.; Castells, F.; Montane, D.

2002-01-01

A life cycle inventory analysis has been conducted to assess the environmental load, specifically CO 2 (fossil) emissions and global warming potential (GWP), associated to the production of hydrogen by the steam reforming of hydrocarbon feedstocks (methane and naphtha) and vegetable oils (rapeseed oil, soybean oil and palm oil). Results show that the GWPs associated with the production of hydrogen by steam reforming in a 100 years time frame are 9.71 and 9.46 kg CO 2 -equivalent/kg H 2 for natural gas and naphtha, respectively. For vegetable oils, the GWP decreases to 6.42 kg CO 2 -equivalent/kg H 2 for rapeseed oil, 4.32 for palm oil and 3.30 for soybean oil. A dominance analysis determined that the part of the process that has the largest effect on the GWP is the steam reforming reaction itself for the fossil fuel-based systems, which accounts for 56.7% and 74% of the total GWP for natural gas and naphtha, respectively. This contribution is zero for vegetable oil-based systems, for which harvesting and oil production are the main sources of CO 2 -eq emissions.(author)

Authentication of vegetable oils on the basis of their physico-chemical properties with the aid of chemometrics.

Science.gov (United States)

Zhang, Guowen; Ni, Yongnian; Churchill, Jane; Kokot, Serge

2006-09-15

In food production, reliable analytical methods for confirmation of purity or degree of spoilage are required by growers, food quality assessors, processors, and consumers. Seven parameters of physico-chemical properties, such as acid number, colority, density, refractive index, moisture and volatility, saponification value and peroxide value, were measured for quality and adulterated soybean, as well as quality and rancid rapeseed oils. Chemometrics methods were then applied for qualitative and quantitative discrimination and prediction of the oils by methods such exploratory principal component analysis (PCA), partial least squares (PLS), radial basis function-artificial neural networks (RBF-ANN), and multi-criteria decision making methods (MCDM), PROMETHEE and GAIA. In general, the soybean and rapeseed oils were discriminated by PCA, and the two spoilt oils behaved differently with the rancid rapeseed samples exhibiting more object scatter on the PC-scores plot, than the adulterated soybean oil. For the PLS and RBF-ANN prediction methods, suitable training models were devised, which were able to predict satisfactorily the category of the four different oil samples in the verification set. Rank ordering with the use of MCDM models indicated that the oil types can be discriminated on the PROMETHEE II scale. For the first time, it was demonstrated how ranking of oil objects with the use of PROMETHEE and GAIA could be utilized as a versatile indicator of quality performance of products on the basis of a standard selected by the stakeholder. In principle, this approach provides a very flexible method for assessment of product quality directly from the measured data.

Elucidation of structural isomers from the homogeneous rhodium-catalyzed isomerization of vegetable oils.

Science.gov (United States)

Andjelkovic, Dejan D; Min, Byungrok; Ahn, Dong; Larock, Richard C

2006-12-13

The structural isomers formed by the homogeneous rhodium-catalyzed isomerization of several vegetable oils have been elucidated. A detailed study of the isomerization of the model compound methyl linoleate has been performed to correlate the distribution of conjugated isomers, the reaction kinetics, and the mechanism of the reaction. It has been shown that [RhCl(C8H8)2]2 is a highly efficient and selective isomerization catalyst for the production of highly conjugated vegetable oils with a high conjugated linoleic acid (CLA) content, which is highly desirable in the food industry. The combined fraction of the two major CLA isomers [(9Z,11E)-CLA and (10E,12Z)-CLA] in the overall CLA mixture is in the range from 76.2% to 93.4%. The high efficiency and selectivity of this isomerization method along with the straightforward purification process render this approach highly promising for the preparation of conjugated oils and CLA. Proposed improvements in catalyst recovery and reusability will only make this method more appealing to the food, paint, coating, and polymer industries in the future.

Quality determination of vegetable oils used as an addition to fermented meat products with different starter cultures

Directory of Open Access Journals (Sweden)

Hana Šulcerová

2017-01-01

Full Text Available There were developed samples of fermented meat products of „Mettwurst" with an addition of a starter culture pentosacceus AS-3/100 or probiotic culture Lactobacillus casei Lc-01 and its combinations for this thesis. A part of animal fat was replaced with vegetable oils - sunflower oil and rapeseed oil. For comparison, there was also used a sample without an addition of vegetable oil. There were determined the characteristics of fats in samples: saponification value, acidity value, esteric, iodine and peroxide value. The samples were determined on the day of production and always once a week in a period of three following weeks. Every single sample was hereby determined 3 times. According to the results, it is more advantageous to use the samples with sunflower oil with an addition of specific cultures Lactobacillus casei Lc-01 and Pediococcus pentosaceus AS-3/100. The saponification value when adding sunflower oil detects that the quality of fat remains stable till the 14th day of storage (p <0.05. The comparison of acid value detects that a sample with sunflower oil and culture Pediococcus pentosaceus AS-3/100 is more advantageous due to fast acidification in the first half of storage period. Good results of iodine and peroxide value had the variation of a sample with sunflower oil and a combination of both cultures. The variation of peroxide value maintained the lowest values. By using the samples with sunflower oil and unispecific cultures L. casei Lc-01 and P. pentosaceus AS-3/100, the culture P. pentosaceus AS-3/100, which remained stable till the 14th day of production, reached the best values of peroxide value. The sunflower oil is in spite of high content of PUFA more stable to which also contributes the increased content of vitamin E that works as an antioxidant here. The disadvantage of rapeseed oil is its higher susceptibility to oxidation. For reasons of faster decomposition of vegetable oils would be essential to cut down on the

Transesterification of waste vegetable oil under pulse sonication using ethanol, methanol and ethanol–methanol mixtures

Energy Technology Data Exchange (ETDEWEB)

Martinez-Guerra, Edith; Gude, Veera Gnaneswar, E-mail: gude@cee.msstate.edu

2014-12-15

Highlights: • Pulse sonication effect on transesterification of waste vegetable oil was studied. • Effects of ethanol, methanol, and alcohol mixtures on FAMEs yield were evaluated. • Effect of ultrasonic intensity, power density, and its output rates were evaluated. • Alcohol mixtures resulted in higher biodiesel yields due to better solubility. - Abstract: This study reports on the effects of direct pulse sonication and the type of alcohol (methanol and ethanol) on the transesterification reaction of waste vegetable oil without any external heating or mechanical mixing. Biodiesel yields and optimum process conditions for the transesterification reaction involving ethanol, methanol, and ethanol–methanol mixtures were evaluated. The effects of ultrasonic power densities (by varying sample volumes), power output rates (in W), and ultrasonic intensities (by varying the reactor size) were studied for transesterification reaction with ethanol, methanol and ethanol–methanol (50%-50%) mixtures. The optimum process conditions for ethanol or methanol based transesterification reaction of waste vegetable oil were determined as: 9:1 alcohol to oil ratio, 1% wt. catalyst amount, 1–2 min reaction time at a power output rate between 75 and 150 W. It was shown that the transesterification reactions using ethanol–methanol mixtures resulted in biodiesel yields as high as >99% at lower power density and ultrasound intensity when compared to ethanol or methanol based transesterification reactions.

Experimental investigation of various vegetable fibers as sorbent materials for oil spills

Energy Technology Data Exchange (ETDEWEB)

Annunciado, T.R.; Sydenstricker, T.H.D.; Amico, S.C. [Federal University of Parana, Curitiba, (Brazil). Department of Mechanical Engineering

2005-11-15

Oil spills are a global concern due to their environmental and economical impact. various commercial systems have been developed to control these spills, including the use of fibers as sorbents. This research investigates the use of various vegetable fibers, namely mixed leaves residues, mixed sawdust, sisal (Agave sisalana), coir fiber (Cocos nucifera), sponge-gourd (Luffa cylindrica) and silk-floss as sorbent materials of crude oil. Sorption tests with crude oil were conducted in deionized and marine water media, with and without agitation. Water uptake by the fibers was investigated by tests in dry conditions and distillation of the impregnated sorbent. The silk-floss fiber showed a very high degree of hydrophobicity and oil sorption capacity of approximately 85 g oil/g sorbent (in 24 hours). Specific gravity measurements and buoyancy tests were also used to evaluate the suitability of these fibers for the intended application. (author)

Composition and properties of virgin pistachio oils and their by-products from different cultivars.

Science.gov (United States)

Ojeda-Amador, Rosa M; Fregapane, Giuseppe; Salvador, María Desamparados

2018-02-01

Pistachios (Pistacia vera) exhibit an interesting nutritional value, due to the high content of oleic acid and minor components with antioxidant and bioactive properties. This work aimed to characterize pistachio virgin oils and their partially defatted residual cakes, obtained from eight cultivars (Aegina, Avdat, Kastel, Kerman, Larnaka, Mateur, Napoletana, and Sirora). Interesting results on phenolics, tocopherols and antioxidant activity were observed, which were greatly affected by variety. Pistachio virgin oils are rich in healthy oleic acid (55-74%), phytosterols (3200-7600mg/kg) and γ-tocopherol (550-720mg/kg). A high content of phenolic compounds (8600-15000mg/kg gallic acid equivalents) and the corresponding antioxidant activities (12-46 and 155-496mmol/kg for DPPH and ORAC) of the residual cakes demonstrate their potential applications as functional ingredients and as rich sources of bioactive compounds. Moreover, virgin pistachio oils possess peculiar and pleasant sensory characteristics, contributing greater added value to the consumers compared to refined vegetable oils. Copyright © 2017 Elsevier Ltd. All rights reserved.

Experimental investigation of evaporation rate and emission studies of diesel engine fuelled with blends of used vegetable oil biodiesel and producer gas

Directory of Open Access Journals (Sweden)

Nanjappan Balakrishnan

2015-01-01

Full Text Available An experimental study to measure the evaporation rates, engine performance and emission characteristics of used vegetable oil methyl ester and its blends with producer gas on naturally aspirated vertical single cylinder water cooled four stroke single cylinder diesel engine is presented. The thermo-physical properties of all the bio fuel blends have been measured and presented. Evaporation rates of used vegetable oil methyl ester and its blends have been measured under slow convective environment of air flowing with a constant temperature and the values are compared with fossil diesel. Evaporation constants have been determined by using the droplet regression rate data. The fossil diesel, biodiesel blends and producer gas have been utilized in the test engine with different load conditions to evaluate the performance and emission characteristics of diesel engine and the results are compared with each other. From these observations, it could be noted that, smoke and hydrocarbon drastically reduced with biodiesel in the standard diesel engine without any modifications.

Combustion of soybean oil and diesel mixtures for heating purposes

Energy Technology Data Exchange (ETDEWEB)

Guimaraes, Adriana Correa; Sanz, Jose Francisco [European University Miguel de Cervantes, Valladolid (Spain)], E-mail: acorrea@uemc.es; Hernandez, Salvador; Navas, Luis Manuel; Rodriguez, Elena; Ruiz, Gonzalo [University of Valladolid (Spain). Dept. of Agricultural and Forest Engineering; San Jose, Julio [University of Valladolid (Spain). Dept. of Energetic Engineering; Gomez, Jaime [University of Valladolid (Spain). Dept. of Communications and Signal Theory and Telematics Engineering

2008-07-01

Using blends of vegetable oils with petroleum derivates for heating purposes has several advantages over other energy application for vegetable oils. This paper presents the results of an investigation by use of soybean oil and diesel mixture as fuel for producing heat in conventional diesel installation. The paper is set out as follows: properties characterization of soybean oil as fuel and of diesel oil, as well as the mixture of both; selection of the mixture according to their physical chemical properties and how they adapt to conventional combustion installation; experimentation with the selected mixture, allowing the main combustion parameters to be measured; processing the collected data, values of combustion, efficiency and reduction of emissions. Conclusions show that the use of soybean oil and diesel mixture for producing heat energy in conventional equipment is feasible and beneficial for reduction emissions. (author)

The use of antioxidants in vegetable oils – A review | Aluyor | African ...

African Journals Online (AJOL)

The shelf life of vegetable oils in food uses and their applicability in industrial situations is greatly dependent on their oxidative stabilities. Methods of improving oxidative stability values currently available include genetic modifications, compositional changes via chemical means, as well as the inhibition of oxidation by ...

Effect of Replacement of Marine Ingredients with Vegetable Oil and Protein on Oxidative Changes during Ice Storage of Rainbow Trout (Oncorhynchus mykiss)

DEFF Research Database (Denmark)

Jacobsen, Charlotte; Eymard, Sylvie; Timm Heinrich, Maike

Recently, fish meal and fish oil have increasingly been replaced with proteins and oils from vegetable sources in the diets of farmed salmonids, but the consequences for the oxidative stability of the resulting fish products have only been investigated to a limited extent. This presentation...... will discuss results from two recent studies from our laboratory on this topic. In the first study, rainbow trout were fed six different diets, which differed in the ratio between marine oil and proteins vs. vegetable oil and protein. Rapeseed oil was used as the oil source and the vegetable proteins were...... a mix based on pea, wheat, sunflower and beans. In the second study, one group of rainbow trout was fed a traditional diet based on fish meal and fish oil, whereas the other five groups were fed diets in which 40 % of the fish meal was replaced with plant proteins from peas, horse bean and rapeseed...

Recycling of waste vegetable oil biodiesel and glycerine : social enterprise feasibility study

International Nuclear Information System (INIS)

2005-12-01

This study examined the feasibility of recycling waste vegetable oil into biodiesel fuel as part of a social enterprise spearheaded by the Centre de sante communautaire in Sudbury. The enterprise proposed the collection of waste vegetable oil from local restaurants for refinement into biodiesel fuel as well as glycerine byproducts. The study included reviews of legal issues related to the project as well as details of community consultation processes. Target participants were also identified. The biodiesel industry was briefly reviewed along with details of the biodiesel manufacturing process. The study determined that 2 permanent employees will be required to run the biodiesel project. Initial staffing for the first year of the project was estimated at 4 full-time equivalent participants. Equipment and capital purchases for the first year of operation were estimated at $75,000. Total funds for startup of the project were estimated at $140,000. Budgets were supplied to the year 2009. 34 refs., 2 tabs., 5 figs

Composition of fatty acids in selected vegetable oils

Directory of Open Access Journals (Sweden)

Helena Frančáková

2015-12-01

Full Text Available Plant oils and fats are important and necessary components of the human nutrition. They are energy source and also contain fatty acids - compounds essential for human health. The aim of this study was to evaluate nutritional quality of selected plant oil - olive, rapeseed, pumpkin, flax and sesame; based on fatty acid composition in these oils. Fatty acids (MUFA, PUFA, SFA were analyzed chromatography using system Agilent 6890 GC, injector multimode, detector FID. The highest content of saturated fatty acids was observed in pumpkinseed oil (19.07%, the lowest content was found in rapeseed oil (7.03%, with low level of palmitic and stearic acids and high level of behenic acid (0.32% among the evaluated oils. The highest content of linoleic acid was determined in pumpkinseed (46.40% and sesame oil (40.49%; in these samples was also found lowest content of α-linolenic acid. These oils have important antioxidant properties and are not subject to oxidation. The richest source of linolenic acid was flaxseed oil which, which is therefore more difficult to preserve and process in food industry. In olive oil was confirmed that belongs to the group of oils with a predominantly monosaturated oleic acid (more than 70% and a small amount of polysaturated fatty acid. The most commonly used rapeseed oil belongs to the group of oils with the medium content of linolenic acid (8.76%; this oil also showed a high content of linoleic acid (20.24%. The group of these essentially fatty acids showed a suitable ratio ∑n3/n6 in the rapessed oil (0.44.

Functionalized Vegetable Oils for Utilization as Polymer Building Blocks: Office of Industrial Technologies (OIT) Agriculture Project Fact Sheet

International Nuclear Information System (INIS)

Carde, T.

2001-01-01

Vegetable oils such as soybean oil will be converted to novel polymers using hydroformylation and other catalytic processes. These polymers can be used in the construction, automotive, packaging, and electronic sectors

Elastohydrodynamic Traction Properties of Seed Oils

Science.gov (United States)

The elastohydrodynamic traction coefficient (tc) properties of nine seed oils of varying chemical structures, PAO and hexadecane, were investigated using a ball-on disk traction apparatus. The seed oils were: castor oil, a triglyceride with hydroxyl functional group; jojoba, a monoglyceride; and s...

Effect of vegetable de-oiled cake-diesel blends on diesel engine

Energy Technology Data Exchange (ETDEWEB)

Raj, C.S. [Bharathiyar College of Engineering and Technology, Karaikal (India). MGR Educational and Research Inst.; Arivalagar, A.; Sendilvelan, S. [MGR Univ., Chennai (India). MGR Educational and Research Inst.; Arul, S. [Panimalar College of Engineering, Channai (India)

2009-07-01

This study evaluated the use of coconut oil methyl ester (COME) as a blending agent with the vegetable de-oiled cakes used in biodiesel production. Different proportions of the de-oiled cake were combined with diesel in order to investigate performance, emissions, and combustion characteristics. The experiments were conducted on a 4-stroke single cylinder, air-cooled diesel engine. Fuel flow rates were measured and a thermocouple was used to measure exhaust gas temperatures. A combustion analyzer was used to measure cylinder pressure and heat release rates. Brake thermal efficiency, brake power, and specific fuel consumption performance was monitored. Results of the study showed that rates of heat release were reduced for the de-oiled cake blended fuels as a result of the change in fuel molecular weight. The variation of NOx with load for neat diesel blends was examined. There was no variation of NOx emission up to 50 per cent of load for all blended oils, and it increased with load. Smoke density was reduced for all blends. Soot production was decreased by the oxygen present in the de-oiled cake. The study showed that fossil fuel oil consumption decreased by 14 to 15 per cent when the de-oiled biodiesel was used at low loads, and 4 to 5 per cent at peak loads. 10 refs., 4 tabs., 9 figs.

Sustainability assessment of straight vegetable oil used as self-supply biofuel in agriculture

OpenAIRE

Baquero Armans, Grau; Esteban Dalmau, Bernat; Puig Vidal, Rita; Riba Ruiz, Jordi-Roger; Rius Carrasco, Antoni

2011-01-01

This work proposes and analyses a model for an agricultural fuel self-supply exploitation. The model is based on the current extended crop rotation of wheat and barley in Anoia region (Catalonia, Spain). The introduction of rapeseed to the current crop rotation and its conversion into oil to be used as agricultural fuel is presented. Life cycle assessment methodology is used to carry out an environmental and an economic assessment. Environmental results show a preference for the vegetable oil...

Comparative performance and emissions study of a direct injection Diesel engine using blends of Diesel fuel with vegetable oils or bio-diesels of various origins

International Nuclear Information System (INIS)

Rakopoulos, C.D.; Antonopoulos, K.A.; Rakopoulos, D.C.; Hountalas, D.T.; Giakoumis, E.G.

2006-01-01

An extended experimental study is conducted to evaluate and compare the use of various Diesel fuel supplements at blend ratios of 10/90 and 20/80, in a standard, fully instrumented, four stroke, direct injection (DI), Ricardo/Cussons 'Hydra' Diesel engine located at the authors' laboratory. More specifically, a high variety of vegetable oils or bio-diesels of various origins are tested as supplements, i.e. cottonseed oil, soybean oil, sunflower oil and their corresponding methyl esters, as well as rapeseed oil methyl ester, palm oil methyl ester, corn oil and olive kernel oil. The series of tests are conducted using each of the above fuel blends, with the engine working at a speed of 2000 rpm and at a medium and high load. In each test, volumetric fuel consumption, exhaust smokiness and exhaust regulated gas emissions such as nitrogen oxides (NO x ), carbon monoxide (CO) and total unburned hydrocarbons (HC) are measured. From the first measurement, specific fuel consumption and brake thermal efficiency are computed. The differences in the measured performance and exhaust emission parameters from the baseline operation of the engine, i.e. when working with neat Diesel fuel, are determined and compared. This comparison is extended between the use of the vegetable oil blends and the bio-diesel blends. Theoretical aspects of Diesel engine combustion, combined with the widely differing physical and chemical properties of these Diesel fuel supplements against the normal Diesel fuel, are used to aid the correct interpretation of the observed engine behavior

Color and chemical properties of oil used for deep frying on a large scale.

Science.gov (United States)

Totani, Nagao; Tateishi, Sayuri; Chiue, Hiroko; Mori, Terutosi

2012-01-01

Acid value (AV), polar compound content (PC), carbonyl value (CV) and Gardner color of oil used for deep-frying in kitchens at a supermarket, lunch chain store, restaurant, eating house, and hospital were analyzed. All AVs obtained but one (3.38) were within the limit set by the Food Sanitation Act of Japan (AV ≤ 3, peroxide value ≤ 30). However, some oil samples had a PC over 25%, which is beyond the limit legislated by some European countries. When the relation between the Gardner color and the AV, PC, or CV of the oil was investigated, well correlated logarithmic regression curves were obtained from the oil of all kitchens except the hospital kitchen. However, the use of lard-containing canola oil without oil replenishment in the eating house increased color values rapidly. All of the values obtained from pure vegetable oil used almost daily were plotted on a graph. It was found that kitchen-by-kitchen differences in fryer, vegetable oil, frying temperature, heating time, and amounts and kinds of foods fried did not influence the relation between Gardner color value versus AV, PC or CV. In conclusion, frying vegetable oil used in large-scale kitchens without official inspection can be better controlled with Gardner color determination by the operators and administrators. This would improve the quality of the oil ingested by facility patrons.

Willingness to pay for safety label on sugar and vegetable oil among ...

African Journals Online (AJOL)

This study investigates willingness to pay for safety label on sugar and vegetable oil among households in South – Western Nigeria. In all, 390 consumers comprising 180 from Oyo and 210 from Lagos were sampled. Data collected include socio-economic, market and food safety information variables using structured ...

Green ultrasound-assisted extraction of carotenoids from pomegranate wastes using vegetable oils.

Science.gov (United States)

Goula, Athanasia M; Ververi, Maria; Adamopoulou, Anna; Kaderides, Kyriakos

2017-01-01

The objective of this work was to develop a new process for pomegranate peels application in food industries based on ultrasound-assisted extraction of carotenoids using different vegetable oils as solvents. In this way, an oil enriched with antioxidants is produced. Sunflower oil and soy oil were used as alternative solvents and the effects of various parameters on extraction yield were studied. Extraction temperature, solid/oil ratio, amplitude level, and extraction time were the factors investigated with respect to extraction yield. Comparative studies between ultrasound-assisted and conventional solvent extraction were carried out in terms of processing procedure and total carotenoids content. The efficient extraction period for achieving maximum yield of pomegranate peel carotenoids was about 30min. The optimum operating conditions were found to be: extraction temperature, 51.5°C; peels/solvent ratio, 0.10; amplitude level, 58.8%; solvent, sunflower oil. A second-order kinetic model was successfully developed for describing the mechanism of ultrasound extraction under different processing parameters. Copyright © 2016 Elsevier B.V. All rights reserved.

Novel approaches to analysis of 3-chloropropane-1,2-diol esters in vegetable oils.

Science.gov (United States)

Moravcova, Eliska; Vaclavik, Lukas; Lacina, Ondrej; Hrbek, Vojtech; Riddellova, Katerina; Hajslova, Jana

2012-03-01

A sensitive and accurate method utilizing ultrahigh performance liquid chromatography (U-HPLC) coupled to high resolution mass spectrometry based on orbitrap technology (orbitrapMS) for the analysis of nine 3-chloropropane-1,2-diol (3-MCPD) diesters in vegetable oils was developed. To remove the interfering triacylglycerols that induce strong matrix effects, a clean-up step on silica gel column was used. The quantitative analysis was performed with the use of deuterium-labeled internal standards. The lowest calibration levels estimated for the respective analytes ranged from 2 to 5 μg kg(-1). Good recovery values (89-120%) and repeatability (RSD 5-9%) was obtained at spiking levels of 2 and 10 mg kg(-1). As an alternative, a novel ambient desorption ionization technique, direct analysis in real time (DART), hyphenated with orbitrapMS, was employed for no separation, high-throughput, semi-quantitative screening of 3-MCPD diesters in samples obtained by chromatographic fractionation. Additionally, the levels of 3-MCPD diesters measured in reallife vegetable oil samples (palm oil, sunflower oil, rapeseed oil) using both methods are reported. Relatively good agreement of the data generated by U-HPLC-orbitrapMS and DART-orbitrapMS were observed. With regard to a low ionization yield achieved for 3-MCPD monoesters, the methods presented in this paper were not yet applicable for the analysis of these contaminants at the naturally occurring levels.

levels of vitamin a fortification in flour and vegetable oils sold in kano

African Journals Online (AJOL)

dambayero

This was carried out by the determination of vitamin A in the flour and vegetable oil samples which .... (biochemically equivalent to iron deficiency anaemia, .... 72. Ong, D.E. and Chytil, F. (1975). Retinol acid binding protein in rat tissue. J. Biol.

Manufacturing of environment friendly biolubricants from vegetable oils

Directory of Open Access Journals (Sweden)

Ebtisam K. Heikal

2017-03-01

Full Text Available Environment friendly products such as fuels and lubricants are among the candidates which are studied in several countries including Egypt. The purpose of this work was to utilize commercially available palm oil and Jatropha oil for the production of biolubricants, through two stages of Transesterification. The first stage is the process of using methanol in the presence of potassium hydroxide to produce biodiesel. The second stage is the reaction of biodiesel with trimethylolpropane using sodium methoxide as catalyst to yield palm or Jatropha oil base trimethylolpropane esters (biolubricants. Palm oil based trimethylolpropane esters with yield of 97.8% was obtained after 4 h of reaction at 130 °C. Under similar reaction conditions, Jatropha oil based trimethylolpropane esters with a yield of 98.2% was obtained. The resulting products were confirmed by FTIR and evaluated by ASTM analyses. The obtained Jatropha oil based trimethylolpropane esters exhibited high viscosity indices (140, low pour point temperature (−3 °C, and moderate thermal stabilities and met the requirement of commercial industrial oil ISO VG46 grade. In spite of the high pour point of Palm oil based trimethylolpropane esters (5 °C, which needs pour point depressant to reduce the pour point, other lubrication properties such as viscosity, viscosity indices and flash point are comparable to commercial industrial oil ISO VG32 and VG46.

Biodiesel. A revision of the obtaining process by means of the transesterification of vegetables oils

International Nuclear Information System (INIS)

Benjumea, Pedro Nel; Agudelo, Jhon Ramiro; Zapata, Paula A; Mendoza, Raul

2003-01-01

Biodiesel is a fuel made from raw materials of renewable origin such as vegetable oils and animal fats. It can be used as an alternative fuel to diesels for use in diesel engines. biodiesel is produced by transesterification of large branched triglycerides into smaller, straight chain molecules of alkyl esters, using a low molecular weight alcohol and an adequate catalyst. The objective of this work is to make an overview about production technology of biodiesel. Research work has been focused in the following variables that affect yield and purity of alkyl esters: type of raw material, type and quantity of catalyst, type of alcohol, molar ratio of alcohol to vegetable oil and reaction temperature

Biodiesel development from rice bran oil: Transesterification process optimization and fuel characterization

International Nuclear Information System (INIS)

Sinha, Shailendra; Agarwal, Avinash Kumar; Garg, Sanjeev

2008-01-01

Increased environmental awareness and depletion of resources are driving industry to develop viable alternative fuels from renewable resources that are environmentally more acceptable. Vegetable oil is a potential alternative fuel. The most detrimental properties of vegetable oils are its high viscosity and low volatility, and these cause several problems during their long duration usage in compression ignition (CI) engines. The most commonly used method to make vegetable oil suitable for use in CI engines is to convert it into biodiesel, i.e. vegetable oil esters using process of transesterification. Rice bran oil is an underutilized non-edible vegetable oil, which is available in large quantities in rice cultivating countries, and very little research has been done to utilize this oil as a replacement for mineral Diesel. In the present work, the transesterification process for production of rice bran oil methyl ester has been investigated. The various process variables like temperature, catalyst concentration, amount of methanol and reaction time were optimized with the objective of producing high quality rice bran oil biodiesel with maximum yield. The optimum conditions for transesterification of rice bran oil with methanol and NaOH as catalyst were found to be 55 deg. C reaction temperature, 1 h reaction time, 9:1 molar ratio of rice bran oil to methanol and 0.75% catalyst (w/w). Rice bran oil methyl ester thus produced was characterized to find its suitability to be used as a fuel in engines. Results showed that biodiesel obtained under the optimum conditions has comparable properties to substitute mineral Diesel, hence, rice bran oil methyl ester biodiesel could be recommended as a mineral Diesel fuel substitute for compression ignition (CI) engines in transportation as well as in the agriculture sector

Modeling the dose effects of soybean oil in salad dressing on carotenoid and fat-soluble vitamin bioavailability in salad vegetables.

Science.gov (United States)

White, Wendy S; Zhou, Yang; Crane, Agatha; Dixon, Philip; Quadt, Frits; Flendrig, Leonard M

2017-10-01

Background: Previously, we showed that vegetable oil is necessary for carotenoid absorption from salad vegetables. Research is needed to better define the dose effect and its interindividual variation for carotenoids and fat-soluble vitamins. Objective: The objective was to model the dose-response relation between the amount of soybean oil in salad dressing and the absorption of 1 ) carotenoids, phylloquinone, and tocopherols in salad vegetables and 2 ) retinyl palmitate formed from the provitamin A carotenoids. Design: Women ( n = 12) each consumed 5 vegetable salads with salad dressings containing 0, 2, 4, 8, or 32 g soybean oil. Blood was collected at selected time points. The outcome variables were the chylomicron carotenoid and fat-soluble vitamin area under the curve (AUC) and maximum content in the plasma chylomicron fraction ( C max ). The individual-specific and group-average dose-response relations were investigated by fitting linear mixed-effects random coefficient models. Results: Across the entire 0-32-g range, soybean oil was linearly related to the chylomicron AUC and C max values for α-carotene, lycopene, phylloquinone, and retinyl palmitate. Across 0-8 g of soybean oil, there was a linear increase in the chylomicron AUC and C max values for β-carotene. Across a more limited 0-4-g range of soybean oil, there were minor linear increases in the chylomicron AUC for lutein and α- and total tocopherol. Absorption of all carotenoids and fat-soluble vitamins was highest with 32 g oil ( P vitamins ( P vitamins could be largely predicted by the soybean oil effect. However, the effect varied widely, and some individuals showed a negligible response. There was a global soybean oil effect such that those who absorbed more of one carotenoid and fat-soluble vitamin also tended to absorb more of the others. This trial was registered at clinicaltrials.gov as NCT02867488. © 2017 American Society for Nutrition.

Tribological Characteristics Evaluation of Mustard Oil Blends

OpenAIRE

Mohammed Hassan Jabal; Muhannad Zaidan Khalefa

2018-01-01

A progressive increase in the desire for environmentally friendly lubricants by users and strict government regulations for the use of these lubricants has provided an opportunity to use plant oils as biodegradable lubricants, therefore vegetable oils have been investigated to replace oil lubricants because of their maintaining the conditions of nature (environment) properties. In this paper, the influences of the blending ratio of mustard seeds oil with commercial mineral oil (SAE40) on the ...

In situ burning of oil in coastal marshes. 1. Vegetation recovery and soil temperature as a function of water depth, oil type, and marsh type.

Science.gov (United States)

Lin, Qianxin; Mendelssohn, Irving A; Bryner, Nelson P; Walton, William D

2005-03-15

In-situ burning of oiled wetlands potentially provides a cleanup technique that is generally consistent with present wetland management procedures. The effects of water depth (+10, +2, and -2 cm), oil type (crude and diesel), and oil penetration of sediment before the burn on the relationship between vegetation recovery and soil temperature for three coastal marsh types were investigated. The water depth over the soil surface during in-situ burning was a key factor controlling marsh plant recovery. Both the 10- and 2-cm water depths were sufficient to protect marsh vegetation from burning impacts, with surface soil temperatures of fire significantly impeded the post-burn recovery of Spartina alterniflora and Sagittaria lancifolia but did not detrimentally affect the recovery of Spartina patens and Distichlis spicata. Oil type (crude vs diesel) and oil applied to the marsh soil surface (0.5 L x m(-2)) before the burn did not significantly affect plant recovery. Thus, recovery is species-specific when no surface water exists. Even water at the soil surface will most likely protect wetland plants from burning impact.

Organic vegetable proteins and oil in feed for organic rainbow trout (Oncorhynchus mykiss)

DEFF Research Database (Denmark)

Lund, Ivar; Dalsgaard, Anne Johanne Tang; Jokumsen, Alfred

The demand for organic trout is increasing, stressing the need for organic, vegetable feed ingredients as replacement for fish meal, as the principles of organic aquaculture encourage the development of feed that do not deplete global fish stocks. In addition, the organic code of practice does...... not allow addition of artificial amino acids to the feed, and optimization of the amino acid profile of organically based diets must therefore derive from the protein sources alone. The aim of this study was to evaluate the digestibility and growth performance of organic vegetable dietary ingredients...... as replacement for fish meal and fish oil in feed for organic rainbow trout (Oncorhynchus mykiss). Six iso-energetic and iso- nitrogenous diets were prepared, comprising a fish meal and fish oil based control diet and three diets in which the inclusion of fish meal was gradually reduced from 59 to 35...

Balancing functional and nutritional quality of oils and fats: Current requirements and future trends

Directory of Open Access Journals (Sweden)

Van den Bremt Karen

2012-03-01

Full Text Available Oils and fats play an important role in the structure, aroma and stability of a wide variety of food products, as well as in their nutritional properties. For Puratos, a producer of ingredients for bakery, patisserie and chocolate sector, functionality and taste are of utmost importance, but the company also wants to contribute to the balanced diet of consumers. Vegetable oils and fats are used in margarines and releasing agents, vegetable creams, compound chocolate, fillings and emulsifiers. Each application requires an oil or fat with specific physicochemical properties in order to ensure the optimal structure, stability and taste of the end product. Traditionally, (partially hydrogenated vegetable oils deliver important functional characteristics concerning crystallization behaviour, directly linked with the workability, melting properties, stability and mouth feel of the food product. However, due to negative nutritional implications, trans fats are to be replaced by healthier alternatives, preferably not by saturated fats. Consumers – and in some regions, legal instances – demand transfree or hydro-free products while not compromising on taste. Alternative fats and oils will be discussed concerning their functional and nutritional properties.

Improving Vegetable Oil Fueled CI Engine Characteristics Through Diethyl Ether Blending

KAUST Repository

Vedharaj, S.

2016-12-01

In this research, the flow and ignition properties of vegetable oil (VO) are improved by blending it with diethyl ether (DEE). DEE, synthesized from ethanol, has lower viscosity than diesel and VO. When DEE is blended with VO, the resultant DEEVO mixtures have favorable properties for compression ignition (CI) engine operation. As such, DEEVO20 (20% DEE + 80% VO) and DEEVO40 (40% DEE + 60% VO) were initially considered in the current study. The viscosity of VO is 32.4*10−6 m2/s; the viscosity is reduced with the increase of DEE in VO. In this study, our blends were limited to a maximum of 40% DEE in VO. The viscosity of DEEVO40 is 2.1*10−6 m2/s, which is comparable to that of diesel (2.3*10−6 m2/s). The lower boiling point and flash point of DEE improves the fuel spray and evaporation for DEEVO mixtures. In addition to the improvement in physical properties, the ignition quality of DEEVO mixtures is also improved, as DEE is a high cetane fuel (DCN = 139). The ignition characteristics of DEEVO mixtures were studied in an ignition quality tester (IQT). There is an evident reduction in ignition delay time (IDT) for DEEVO mixtures compared to VO. The IDT of VO (4.5 ms), DEEVO20 (3.2 ms) and DEEVO40 (2.7 ms) was measured in IQT. Accordingly, the derived cetane number (DCN) of DEEVO mixtures increased with the increase in proportion of DEE. The reported mixtures were also tested in a single cylinder CI engine. The start of combustion (SOC) was advanced for DEEVO20 and DEEVO40 compared to diesel, which is attributed to the high DCN of DEEVO mixtures. On the other hand, the peak heat release rate decreased for DEEVO mixtures compared to diesel. Gaseous emissions such as nitrogen oxide (NOX), total hydrocarbon (THC) and smoke were reduced for DEEVO mixtures compared to diesel. The physical and ignition properties of VO are improved by the addition of DEE, and thus, the need for the trans-esterification process is averted. Furthermore, this blending strategy is simpler

Improving Vegetable Oil Fueled CI Engine Characteristics Through Diethyl Ether Blending

KAUST Repository

Vedharaj, S.; Vallinayagam, R.; Sarathy, Mani; Dibble, Robert W.

2016-01-01

In this research, the flow and ignition properties of vegetable oil (VO) are improved by blending it with diethyl ether (DEE). DEE, synthesized from ethanol, has lower viscosity than diesel and VO. When DEE is blended with VO, the resultant DEEVO mixtures have favorable properties for compression ignition (CI) engine operation. As such, DEEVO20 (20% DEE + 80% VO) and DEEVO40 (40% DEE + 60% VO) were initially considered in the current study. The viscosity of VO is 32.4*10−6 m2/s; the viscosity is reduced with the increase of DEE in VO. In this study, our blends were limited to a maximum of 40% DEE in VO. The viscosity of DEEVO40 is 2.1*10−6 m2/s, which is comparable to that of diesel (2.3*10−6 m2/s). The lower boiling point and flash point of DEE improves the fuel spray and evaporation for DEEVO mixtures. In addition to the improvement in physical properties, the ignition quality of DEEVO mixtures is also improved, as DEE is a high cetane fuel (DCN = 139). The ignition characteristics of DEEVO mixtures were studied in an ignition quality tester (IQT). There is an evident reduction in ignition delay time (IDT) for DEEVO mixtures compared to VO. The IDT of VO (4.5 ms), DEEVO20 (3.2 ms) and DEEVO40 (2.7 ms) was measured in IQT. Accordingly, the derived cetane number (DCN) of DEEVO mixtures increased with the increase in proportion of DEE. The reported mixtures were also tested in a single cylinder CI engine. The start of combustion (SOC) was advanced for DEEVO20 and DEEVO40 compared to diesel, which is attributed to the high DCN of DEEVO mixtures. On the other hand, the peak heat release rate decreased for DEEVO mixtures compared to diesel. Gaseous emissions such as nitrogen oxide (NOX), total hydrocarbon (THC) and smoke were reduced for DEEVO mixtures compared to diesel. The physical and ignition properties of VO are improved by the addition of DEE, and thus, the need for the trans-esterification process is averted. Furthermore, this blending strategy is simpler

Experimental investigation of various vegetable fibers as sorbent materials for oil spills.

Science.gov (United States)

Annunciado, T R; Sydenstricker, T H D; Amico, S C

2005-11-01

Oil spills are a global concern due to their environmental and economical impact. Various commercial systems have been developed to control these spills, including the use of fibers as sorbents. This research investigates the use of various vegetable fibers, namely mixed leaves residues, mixed sawdust, sisal (Agave sisalana), coir fiber (Cocos nucifera), sponge-gourd (Luffa cylindrica) and silk-floss as sorbent materials of crude oil. Sorption tests with crude oil were conducted in deionized and marine water media, with and without agitation. Water uptake by the fibers was investigated by tests in dry conditions and distillation of the impregnated sorbent. The silk-floss fiber showed a very high degree of hydrophobicity and oil sorption capacity of approximately 85goil/g sorbent (in 24hours). Specific gravity measurements and buoyancy tests were also used to evaluate the suitability of these fibers for the intended application.

Feed based on vegetable materials changes the muscle proteome of the carnivore rainbow trout

DEFF Research Database (Denmark)

Jessen, Flemming; Wulff, Tune; Bach Mikkelsen, J.

2011-01-01

Feed production for aquaculture of carnivore fish species relies heavily on protein and lipid from the limited resources of wild fish and other sea living organisms. Thus the development of alternative feeds replacing fish meal and oil with components of vegetable origin is important for a sustai......Feed production for aquaculture of carnivore fish species relies heavily on protein and lipid from the limited resources of wild fish and other sea living organisms. Thus the development of alternative feeds replacing fish meal and oil with components of vegetable origin is important...... trout fed two different diets identical in protein and oil content, but with diet C based on fish meal and oil and diet V based on rapeseed oil and vegetable proteins. In addition to the proteomic investigation the textural properties of the fish were analysed by sensory profiling. Protein expression...

Type of vegetable oils used in cooking and risk of metabolic syndrome among Asian Indians.

Science.gov (United States)

Lakshmipriya, Nagarajan; Gayathri, Rajagopal; Praseena, Kallingal; Vijayalakshmi, Parthasarathy; Geetha, Gunasekaran; Sudha, Vasudevan; Krishnaswamy, Kamala; Anjana, Ranjit Mohan; Henry, Jeyakumar; Mohan, Viswanathan

2013-03-01

There is little data on the type of vegetable oil used and the prevalence of metabolic syndrome (MS) in Asian Indians. Food frequency questionnaire was used to document the type of cooking oil in 1875 adults in Chennai city. MS was assessed by new harmonizing criteria. The prevalence of MS was higher among sunflower oil users (30.7%) than palmolein (23.2%) and traditional oil (17.1%, p < 0.001) users. The higher prevalence of MS in sunflower oil group persisted even when stratified according to body mass index, except in obese groups. The risk of MS was further compounded by quantity of refined cereals consumed. Higher LA%E and linoleic acid/alpha-linolenic acid ratio in sunflower oil probably contributes to increased risk of MS.

A new analytical method for quantification of olive and palm oil in blends with other vegetable edible oils based on the chromatographic fingerprints from the methyl-transesterified fraction.

Science.gov (United States)

Jiménez-Carvelo, Ana M; González-Casado, Antonio; Cuadros-Rodríguez, Luis

2017-03-01

A new analytical method for the quantification of olive oil and palm oil in blends with other vegetable edible oils (canola, safflower, corn, peanut, seeds, grapeseed, linseed, sesame and soybean) using normal phase liquid chromatography, and applying chemometric tools was developed. The procedure for obtaining of chromatographic fingerprint from the methyl-transesterified fraction from each blend is described. The multivariate quantification methods used were Partial Least Square-Regression (PLS-R) and Support Vector Regression (SVR). The quantification results were evaluated by several parameters as the Root Mean Square Error of Validation (RMSEV), Mean Absolute Error of Validation (MAEV) and Median Absolute Error of Validation (MdAEV). It has to be highlighted that the new proposed analytical method, the chromatographic analysis takes only eight minutes and the results obtained showed the potential of this method and allowed quantification of mixtures of olive oil and palm oil with other vegetable oils. Copyright © 2016 Elsevier B.V. All rights reserved.

Reduction of gaseous pollutants and particulate materials by using fuels derived from vegetable in substitution to diesel oil; Reducao de poluentes gasosos e de material particulado por meio do uso de combustiveis a base de oleos vegetais como substitutos ao oleo diesel

Energy Technology Data Exchange (ETDEWEB)

Yazaki, Carlos Kazuaki [General Motors do Brasil, Sao Caetano do Sul, SP (Brazil). Engenharia de Chassis e Integracao Powertrain]. E-mail: carlos.yazaki@gm.com; Trielli, Mauricio Assumpcao [Sao Paulo Univ., SP (Brazil). Escola Politecnica. Dept. de Engenharia Mecanica]. E-mail: trielli@ipt.br

2006-07-01

The aim of this article is to present the contribution allowed by fuels derived from vegetable oils in substitution for the diesel oil. It especially emphasizes the vegetable oil esters potential as gaseous exhaust pollutant and particulate matter reduction produced by ignition compression engines, such a conclusion has been achieved through systematization and analysis of results of experimental tests performed by several researchers that applied natural vegetable oils and their esters to this class of engines. Once the vegetable oils are the base of formation of these fuels, their direct application in these engines is also analyzed showing the advantages and disadvantages of this alternative route. This article also includes an analysis of their physical and chemical properties which help the understanding of their performance in the engines. Due to better results obtained from esters use, their industrial processing, the special characteristics of the engineering materials which they will have contact in engine, principally those used in injection systems, as well as aspects related to their storages are discussed too. (author)

The Protective Effect of Hippophae Rhamnoides Carotenoid Extract Against Lipid Peroxidation in Crude Vegetable Oils

Directory of Open Access Journals (Sweden)

Sanda Andrei

2014-11-01

Full Text Available Vegetable oils are important elements of the human diet because they contain essential nutritional factors. Due to the manufacturing processes or inadequate conditions of storage, they may also contain lipid oxidation products that are toxic to the body. The purpose of this paper is to test the protective effect of carotenoid-rich extracts obtained from the fruits of Hippophae rhamnoides on crude sunflower, pumpkin and olive oils oxidative processes. In order to evaluate the effect of antioxidant carotenoids, three stages were followed: thermal induction of lipid peroxidation in the presence of AAPH (2,2'-Azobis(2-amidinopropane dihydrochloride; determination of the level of lipid peroxidation in oxidized oils in the presence and absence of antioxidants, by quantifying the concentration of conjugated dienes and malonyl dialdehyde (MDA; determination of the level of lipid peroxidation by evaluating the profile of the fatty acids and the ratio between the saturated and unsaturated fatty acids (UFA / SFA, using an GC-MS method. In the case of sunflower oil, it was observed that sea buckthorn fruit extract significantly decreased MDA concentration but does not significantly reduce the concentration of conjugated dienes. The protective effect of carotenoids is more evident in the case of oil from pumpkin seeds. In the olive oil, unlike the first two types of oils, the carotenoids extract inhibits both the MDA and the conjugated dienes formation to a lesser extent, statistically insignificant. Overall, the ratio UFA / SFA decreases in crude oxidized oils. In the oils in which carotenoids were added was observed an increase in the UFA / SFA ratio. Carotenoids fraction from sea buckthorn fruits, rich in xanthophylls’ esters, possess a good antioxidant effect, protecting vegetable oils against peroxidation processes induced in the presence of AAPH

A novel cardanol-based antioxidant and its application in vegetable oils and biodiesel

Science.gov (United States)

A novel antioxidant, epoxidized cardanol (ECD), derived from cardanol has been synthesized and characterized by FT-IR, 1H-NMR and 13C-NMR. Oxidative stability of ECD in vegetable oils and biodiesel was evaluated by the pressurized differential scanning calorimetry and Rancimat methods, respectively....

Determination of some inorganic metals in edible vegetable oils by inductively coupled plasma atomic emission spectroscopy (ICP-AES

Directory of Open Access Journals (Sweden)

Musa Özcan, M.

2008-09-01

Full Text Available Seventeen edible vegetable oils were analyzed spectrometrically for their metal (Cu, Fe, Mn, Co, Cr, Pb, Cd, Ni, and Zn contents. Toxic metals in edible vegetable oils were determined by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES. The highest metal concentrations were measured as 0.0850, 0.0352, 0.0220, 0.0040, 0.0010, 0.0074, 0.0045, 0.0254 and 0.2870 mg/kg for copper in almond oil, for iron in corn oil-(c, for manganese in soybean oil, for cobalt in sunflower oil-(b and almond oil, for chromium in almond oil, for lead in virgin olive oil, for cadmium in sunflower oil-(e, for nickel almond oil and for zinc in almond oil respectively. The method for determining toxic metals in edible vegetable oils by using ICP-AES is discussed. The metals were extracted from low quantities of oil (2-3 g with a 10% nitric acid solution. The extracted metal in acid solution can be injected into the ICPAES. The proposed method is simple and allows the metals to be determined in edible vegetable oils with a precision estimated below 10% relative standard deviation (RSD for Cu, 5% for Fe, 15% for Mn, 8% for Co, 10% for Cr, 20% for Pb, 5% for Cd, 16% for Ni and 11% for Zn.En este estudio se analizó espectrométricamente el contenido en metales (Cu, Fe, Mn, Co, Cr, Pb, Cd, Ni, and Zn de 17 aceites vegetales comestibles mediante ICP-AES. Las concentaciones más elevadas se encontraron para el cobre en el aceite de almendra (0.0850 mg/kg, para el hierro en el aceite de maiz(c,(0.0352 mg/kg, para el manganeso en el aceite de soja (0.0220 mg/kg, para el cobalto en el aceite de girasol (b (0.0040 mg/kg, para el cromo en el aceite de almendra (0.0010 mg/kg, para el plomo en el aceite de oliva virgen (0.0074 mg/kg, para el cadmio en el aceite de girasol (e (0.0045 mg/kg, para el niquel en el aceite de almendra (0.0254 mg/kg y para el zincen el aceite de almendra (0.2870 mg/kg. Los metales se extrajeron a partir de bajas cantidades de aceite (2-3 g, con

Monitoring of oil palm plantations and growth variations with a dense vegetation model

DEFF Research Database (Denmark)

Teng, Khar Chun; Koay, Jun Yi; Tey, Seng Heng

2014-01-01

The development of microwave remote sensing models for the monitoring of vegetation has received wide attention in recent years. For vegetation in the tropics, it is necessary to consider a dense medium model for the theoretical modelling of the microwave interaction with the vegetation medium....... In this paper, a multilayer model based on the radiative transfer theory for a dense vegetation medium is developed where the coherence effects and near field interaction effects of closely spaced leaves and branches are considered by incorporating the Dense Medium Phase and Amplitude Correction Theory (DM......-PACT) and Fresnel Phase Corrections. The iterative solutions of the radiative transfer model are computed with input based on ground truth measurements of physical parameters of oil palm plantations in the state of Perak, Malaysia, and compared with the SAR images obtained from RADARSAT2. Preliminary results...

Instantaneous characterization of vegetable oils via TAG and FFA profiles by easy ambient sonic-spray ionization mass spectrometry.

Science.gov (United States)

Simas, Rosineide C; Catharino, Rodrigo R; Cunha, Ildenize B S; Cabral, Elaine C; Barrera-Arellano, Daniel; Eberlin, Marcos N; Alberici, Rosana M

2010-04-01

A fast and reliable method is presented for the analysis of vegetable oils. Easy ambient sonic-spray ionization mass spectrometry (EASI-MS) is shown to efficiently desorb and ionize the main oil constituents from an inert surface under ambient conditions and to provide comprehensive triacylglyceride (TAG) and free fatty acid (FFA) profiles detected mainly as either [TAG + Na](+) or [FFA-H](-) ions. EASI(+/-)-MS analysis is simple, easily implemented, requires just a tiny droplet of the oil and is performed without any pre-separation or chemical manipulation. It also causes no fragmentation of TAG ions hence diacylglyceride (DAG) and monoacylglyceride (MAG) profiles and contents can also be measured. The EASI(+/-)-MS profiles of TAG and FFA permit authentication and quality control and can be used, for instance, to access levels of adulteration, acidity, oxidation or hydrolysis of vegetable oils in general.

The use of isotope ratios (13C/12C) for vegetable oils authentication

Science.gov (United States)

Cristea, G.; Magdas, D. A.; Mirel, V.

2012-02-01

Stable isotopes are now increasingly used for the control of the geographical origin or authenticity of food products. The falsification may be more or less sophisticated and its sophistication as well as its costs increases with the improvement of analytical methods. In this study 22 vegetable oils (olive, sunflower, palm, maize) commercialized on Romanian market were investigated by mean of δ13C in bulk oil and the obtained results were compared with those reported in literature in order to check the labeling of these natural products. The obtained results were in the range of the mean values found in the literature for these types of oils, thus providing their accurate labeling.

Sedimentation and deformation of an aqueous sodium hydroxide drop in vegetable oil

Science.gov (United States)

White, Andrew; Hyacinthe, Hyaquino; Ward, Thomas

2013-11-01

The addition of water droplets in fuels is known to provide benefits such as decreased Nitrous Oxide NOx emissions. Unfortunately the shelf life of a water-fuel emulsion is limited by the sedimentation rate of the water droplets. It is well known that adding surfactants can significantly slow the sedimentation rate due to the introduction of Marangoni stresses. In the case of a vegetable oil fuel, adding sodium hydroxide (NaOH) to the water droplets will produce surfactants through saponification in the form of sodium-carboxylate salts. Pendant drops of aqueous NaOH solutions with pH between 11 and 13 will be suspended in several oils such as corn, olive, canola and soybean oil in order to measure the interfacial tension. The change in interfacial tension with time will be used to estimate the surfactant concentration and the saponification rate. Then individual drops will be placed in the oils to observe the settling velocity and drop deformation. NSF CBET.

Inward Processing Regime Promotion System in Vegetable Oil Industry: A Case Study of Turkey

Directory of Open Access Journals (Sweden)

Sinan Duru

2017-04-01

Full Text Available This study was conducted to determine applicability of the Inward Processing Regime (IPR in enterprises which are vegetable oil producers and exporters. The data was obtained from 26 vegetable oil producer and exporter enterprises by using survey method. Frequency tables, indices, and percentage calculating were used to analyse Data. Also, SWOT analysis was used to determine the strengths, weaknesses, opportunities and threats in the sector, and relationship among some variables were examined with correlation coefficient. According to research findings, 25 of the enterprises (96% utilised the IPR. Since the enterprises started to use that system; availability of cheap raw material, rate of capacity utilisation, market share, and export value all have increased. In addition, raw material was found as an important expense item, and the most important problems were qualified as raw material inadequacy and high input prices.

Biodiesel production from vegetable oil: Process design, evaluation and optimization

Directory of Open Access Journals (Sweden)

Kianimanesh Hamid Reza

2017-09-01

Full Text Available To investigate the effect of reactor performance/configuration of biodiesel production on process parameters (mass & energy consumption, required facilities etc., two diverse production processes (from vegetable oil were implemented/designed using Aspen HYSYS V7.2. Two series reactors were taken into account where overall conversion was set to be 97.7% and 70% in first and second processes respectively. Comparative analysis showed that an increase in conversion yield caused to consumption reduction of oil, methanol, cold energy and hot energy up to 9.1%, 22%, 67.16% and 60.28% respectively; further, a number of facilities (e.g. boiler, heat exchanger, distillation tower were reduced. To reduce mass & energy consumption, mass/heat integration method was employed. Applying integration method showed that in the first design, methanol, cold and hot energy were decreased by 49.81%, 17.46% and 36.17% respectively; while in the second design, oil, methanol, cold and hot energy were decreased by 9%, 60.57% 19.62% and 36.58% respectively.

Utilization of some non-edible oil for biodiesel production ...

African Journals Online (AJOL)

In this work, the production of biodiesel from four sources of non-edible oils, namely jatropha, animal fat, waste vegetable oil and castor oil was carried out. It was done using an acid esterification process followed by alkali transesterification in the laboratory. Subsequently the physicochemical properties for four blends B100 ...

Recovery of different waste vegetable oils for biodiesel production: a pilot experience in Bahia State, Brazil.

Science.gov (United States)

Torres, Ednildo Andrade; Cerqueira, Gilberto S; Tiago, M Ferrer; Quintella, Cristina M; Raboni, Massimo; Torretta, Vincenzo; Urbini, Giordano

2013-12-01

In Brazil, and mainly in the State of Bahia, crude vegetable oils are widely used in the preparation of food. Street stalls, restaurants and canteens make a great use of palm oil and soybean oil. There is also some use of castor oil, which is widely cultivated in the Sertão Region (within the State of Bahia), and widely applied in industry. This massive use in food preparation leads to a huge amount of waste oil of different types, which needs either to be properly disposed of, or recovered. At the Laboratorio Energia e Gas-LEN (Energy & Gas lab.) of the Universidade Federal da Bahia, a cycle of experiments were carried out to evaluate the recovery of waste oils for biodiesel production. The experiences were carried out on a laboratory scale and, in a semi-industrial pilot plant using waste oils of different qualities. In the transesterification process, applied waste vegetable oils were reacted with methanol with the support of a basic catalyst, such as NaOH or KOH. The conversion rate settled at between 81% and 85% (in weight). The most suitable molar ratio of waste oils to alcohol was 1:6, and the amount of catalyst required was 0.5% (of the weight of the incoming oil), in the case of NaOH, and 1%, in case of KOH. The quality of the biodiesel produced was tested to determine the final product quality. The parameters analyzed were the acid value, kinematic viscosity, monoglycerides, diglycerides, triglycerides, free glycerine, total glycerine, clearness; the conversion yield of the process was also evaluated. Copyright © 2013 Elsevier Ltd. All rights reserved.

Simultaneous determination of zearalenone and its derivatives in edible vegetable oil by gel permeation chromatography and gas chromatography-triple quadrupole mass spectrometry.

Science.gov (United States)

Qian, Mingrong; Zhang, Hu; Wu, Liqin; Jin, Nuo; Wang, Jianmei; Jiang, Kezhi

2015-01-01

A sensitive gas chromatographic-triple quadrupole mass spectrometric (GC-QqQ MS) analytical method, for the determination of zearalenone and its five derivatives in edible vegetable oil, was developed. After the vegetable oil samples were prepared using gel permeation chromatography, the eluent was collected, evaporated and dried with nitrogen gas. The residue was silylated with N,O-bis-trimethylsilyltrifluoroacetamide, containing 1% trimethylchlorosilane. GC-QqQ MS was performed in the reaction-monitoring mode to confirm and quantify mycotoxins in vegetable oil. The limits of quantitation were 0.03-0.2 μg kg(-1) for the six mycotoxins. The average recoveries, measured at 2, 20 and 200 μg kg(-1), were in the range 80.3-96.5%. Zearalenone was detected in the range 5.2-184.6 μg kg(-1) in nine maize oils and at 40.7 μg kg(-1) in a rapeseed oil from the local market. Copyright © 2014 Elsevier Ltd. All rights reserved.

EFFECT OF NON-TRADITIONAL VEGETABLE RAW MATERIALS ON THE PROPERTIES AND BIOTECHNOLOGICAL STRUCTURE PASTRY

Directory of Open Access Journals (Sweden)

Y. P. Kolomnikova

2015-01-01

Full Text Available Summary. An important task is the use of catering in the preparation of food products of new types of raw materials, which can solve the problem of nutrition. One way to improve the quality and range of flour culinary products is the use of technology in their enriching additives plant. Among them are a subgroup of additives derived from cereals, pulses, oilseeds, vegetables, fruit and other plant materials. As a result of researches the technology buns bakery products with the addition of oil and meal of wheat germ, pumpkin seed oil cake. Wheat germ oil cake is a source of complete protein and biologically active substances, is rich in essential amino acids, unsaturated ω-3, ω-6 fatty acids, vitamin E, D, B1, B2, B6, PP, pantothenic and folic acid, carotenoids. The composition of pumpkin seed oil cake include essential oils, phytosterols, resinous substances, organic acids, vitamins C and B, carotenoids, carbohydrate melen. In the composition of wheat germ oil contains: all essential, not synthesized by the human amino acid (tryptophan, methionine, leucine, valine, isoleucine, polyunsaturated fatty acids (ω-3, ω-6 and ω-9 acid, a large amount of vitamins, micro - and macronutrients. In the development of the experimental basis for the formulation chosen butter bakery products, in which part of the wheat flour (20 % was replaced by wheat germ oil cake (10 % and pumpkin seed oil cake (10 %. Margarine in the classical formulation was replaced by wheat germ oil, sugar - on natural honey. Insertion additives significantly improve the properties of biotech pastry. The proposed method of production of buns bakery products can reduce the duration of the production process, to intensify the process of gas formation in the test to increase gas-retaining capacity and lift test.

Relationship between the standing vegetation, soil properties and ...

African Journals Online (AJOL)

This study assessed the floristic composition, soil properties and the soil seedbank of the vegetation around the Iron smelting factory. This was with a view to determining the functional role played by soil chemical composition and the seed bank in the modifications of vegetation patterns. Five 100 m × 5 m plots were ...

Conference Proceedings: Structuring oil and gas property transactions

International Nuclear Information System (INIS)

1999-01-01

The 12 presentations at this conference dealt with issues concerning the legal aspects of oil and gas property transaction agreements. Several issues regarding sales and purchase negotiations of oil and gas property are reviewed and some of the basic principles of contract law are explained. Advantages, disadvantages and opportunities of structuring oil and gas property acquisitions, as well as their tax consequences are also identified. The issue of risk assessment regarding environmental consequences and how public concerns regarding the state of the environment has had an impact on oil and gas transactions, is addressed. Interest in this topic stems from the fact that improved enforcement of existing laws regarding the environment can potentially make purchasers liable for significant costs associated with remediation or clean-up of contaminated properties. refs., tabs., figs

Review of antidiabetic fruits, vegetables, beverages, oils and spices commonly consumed in the diet.

Science.gov (United States)

Beidokhti, Maliheh Najari; Jäger, Anna K

2017-04-06

Type 2 diabetes is the most common type of diabetes and its prevalence is rapidly increasing throughout the world. Modifications of lifestyle such as suitable diet and exercise programs along with pharmacotherapy and education of patients are beneficial therapies for patients with type 2 diabetes. The ethnopharmacological use of herbal medicines, many of them part of our diet as spices, vegetables and fruits, has been developed for the treatment of diabetes due to inexpensiveness, easy availability and few side effects. Our aim is to present a review for researchers who are interested in the biologically active dietary plants traditionally utilized in the treatment of diabetes. Information was obtained from a literature search of electronic databases such as Google Scholar, Pubmed, Sci Finder and Cochrane. Common and scientific name of the fruits, vegetables, beverages, oils and spices and the words 'antidiabetic', 'hypoglycemic', 'anti-hyperglycemic', 'type 2 diabetes' were used as keywords for search. Certain fruits and vegetables are functional foods and their consumption reduces the incidence of type 2 diabetes. Hypoglycemic effects of fruits and vegetables may be due to their inducing nature on pancreatic β-cells for insulin secretion, or bioactive compounds such as flavonoids, alkaloids and anthocyanins, which act as insulin-like molecules or insulin secretagogues. This write-up covers hypoglycemic, anti-hyperglycemic and anti-diabetic activities of some dietary fruits, vegetables, beverages, oils and spices and their active hypoglycemic constituents. Including such plant species in the diet might improve management of type 2 diabetes. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

Statistical properties of country risk ratings under oil price volatility: Evidence from selected oil-exporting countries

International Nuclear Information System (INIS)

Liu, Chang; Sun, Xiaolei; Chen, Jianming; Li, Jianping

2016-01-01

This paper focuses on the application of panel models for identification and analysis of influence of oil price volatility on statistical properties of country risk ratings which stem from uncertainty of macroeconomic fluctuations. Firstly, two statistical properties of country risk ratings, volatility clustering and asymmetrical revision were identified in a theoretical framework based on Cruces (2006). Secondly, considering the oil price volatility, numerical experiments were conducted based on extended models to test and verify specific properties of country risk ratings in selected oil-exporting countries. Empirical results suggest that properties of country risk remain comparatively steady despite oil price volatility. It is also found that the oil price volatility can obviously exaggerate the country risk volatility, as it happened during 2007–2009. Country clustering based on the properties of country risk ratings shows that the selected countries maintain a significant clustering tendency. These features are of great importance for estimating risk exposure of international trade and investments in oil export during extreme situations. - Highlights: •Relationship between oil price volatility and country risk is the focus. •An extended model based on Cruces (2006) is proposed. •Volatility clustering and asymmetrical revision of country risk ratings is explored. •Oil price volatility can obviously exaggerate properties of country risk volatility.

Potential and limitations of biomass production for energy purposes: Vegetable oils compared with alcohol

International Nuclear Information System (INIS)

Andrade, C.S.; Rosa, L.P.

1984-01-01

Since Brazil has favourable conditions for biomass production, as regards land mass, soil and climate, several agricultural products have been proposed as alternatives to petroleum-derived fuels. An analysis is made of the potential and limitations of energy systems using biomass production aimed at the use of vegetable oils in diesel engines compared with the experience acquired in Brazil with alcohol fuel in Otto engines. The current status of the national programme for alcohol production (PNA) within the framework of Brazilian agriculture in the last few years is presented, taking into account its objectives, achievements and impacts. Regarding vegetable oils, it must be emphasized that freight and mass passenger transport is being researched in every aspect - from the agricultural production of oleaginous plants to the use of oils in diesel engines. To assess the potential of oleaginous plant production, land needs for the years 1990 and 2000 have been estimated. From the study of some selected oleaginous plants and their potential expansion in a realistic way it was concluded that the viability of this alternative to diesel oil is limited in the short and medium term compared with alcohol, which provides better conditions for great expansion in the short term. It is believed that the option is viable, provided that it is launched gradually to avoid repeating the negative impacts that (according to some experts) were generated by PNA. (author)

Elastohydrodynamic (EHD) traction properties of seed oils

Science.gov (United States)

The elastohydrodynamic traction coefficient (tc) properties of nine seed oils of varying chemical structures, PAO and hexadecane, were investigated using a ball-on disk traction apparatus. The seed oils were: castor oil, a triglyceride with hydroxyl functional group; jojoba, a monoglyceride; and sev...

Environmental audits of oil and gas properties

International Nuclear Information System (INIS)

Moody, T.D.; Forbes, S.

1991-01-01

The growing concern over one, the cost of correcting environmental damage and two, the potential financial liabilities associated with the acquisition, sale or lease of oil and gas properties, has led many prospective buyers to investigate the environmental liabilities associated with the property transfer. The environmental audit provides a tool or mechanism to assist the prudent investor in identifying environmental problems that could adversely effect an otherwise normal business activity. Accordingly, an environmental audit can identify potential environmental liabilities associated with the property, thus allowing the investor an opportunity to better assess financial risks. In addition, should the negative findings of the environmental audit be limited, the findings could be used by the buyer in negotiating the final price of the subject property to account for potential or known liabilities. As this suggests, environmental damage to an oil and gas property does not necessarily render the property worthless. This paper provides a brief guide on environmental audits of oil and gas properties as well as general information on the most common exploration and production wastes

Estimation of Stereospecific Fatty Acid Distribution in Vegetable Oils from Liquid Chromatography Data.

Czech Academy of Sciences Publication Activity Database

Sovová, Helena; Lísa, M.; Holčapek, M.

2008-01-01

Roč. 110, č. 3 (2008), s. 266-276 ISSN 1438-7697 R&D Projects: GA AV ČR(CZ) GA203/04/0120 Institutional research plan: CEZ:AV0Z40720504 Keywords : vegetable oils * triacylglycerol * stereospecificity Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.354, year: 2008

Evaluation of emissions in gas powered electric generator engine with vegetable oil; Avaliacao das emissoes de gases em motor gerador eletrico alimentado com oleo vegetal

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Thalita C. de; Cunha, Joao Paulo Barreto; Cotrim, Suzane Santana; Brito, Gustavo Mendes; Delmond, Josue Gomes [Universidade Estadual de Goias (UNUCET/UEG), Anapolis, GO (Brazil). Unidade Universitaria de Ciencias Exatas e Tecnologicas], E-mail: thalitacarrijo@gmail.com

2012-11-01

The use of vegetable oils as fuel in diesel engines is a good alternative to reduce emissions of greenhouse gases in the atmosphere from the use of fossil fuels, either in pure form or as biodiesel. The soybean, oilseed single high-availability in Brazil, is the most viable feedstock for the production of oil and its use as a fuel because of the structure of production, distribution and grain crushing. This study aimed to evaluate the performance of a duty diesel generator fueled with blends of diesel and soybean oil at concentrations of 10%, 25%, 50% and 75%, and soybean oil pure, 100%. During the tests we evaluated the energy consumption of the generator and the emission of greenhouse gases (O{sub 2}, CO, CO{sub 2}, NO{sub x} and SO{sub 2}), according to the demand of electric charges (0, 500, 1000, 1500 and 2000 Watts) connected to the group generator. The results, using the F test, showed that the hourly consumption of fuel increased with increasing concentration in the mixture of diesel fuel and engine load demand from the generator. It follows that in the environment, increasing the oil concentration in the mixture caused a reduction in emissions, except for the emission of oxygen. The best choice for the operation for the engine generator using vegetable oil soya be provided for up to 60 % oil in the mixture and load demand up to 1000W, in which occurred lower emissions of carbon monoxide (CO) and therefore improved efficiency in the combustion process. (author)

Use of Isomerization and Hydroisomerization Reactions to Improve the Cold Flow Properties of Vegetable Oil Based Biodiesel

Directory of Open Access Journals (Sweden)

Stephen J. Reaume

2013-01-01

Full Text Available Biodiesel is a promising alternative to petroleum diesel with the potential to reduce overall net CO2 emissions. However, the high cloud point of biodiesel must be reduced when used in cold climates. We report on the use of isomerization and hydroisomerization reactions to reduce the cloud point of eight different fats and oils. Isomerization was carried out at 260 °C and 1.5 MPa H2 pressure utilizing beta zeolite catalyst, while hydroisomerization was carried out at 300 °C and 4.0 MPa H2 pressure utilizing 0.5 wt % Pt-doped beta zeolite catalyst. Reaction products were tested for cloud point and flow properties, in addition to catalyst reusability and energy requirements. Results showed that high unsaturated fatty acid biodiesels increased in cloud point, due to the hydrogenation side reaction. In contrast, low unsaturated fatty acid biodiesels yielded cloud point reductions and overall improvement in the flow properties. A maximum cloud point reduction of 12.9 °C was observed with coconut oil as the starting material. Results of the study have shown that branching can reduce the cloud point of low unsaturated fatty acid content biodiesel.

Biodiesel's Characteristics Preparation from Palm Oil

Directory of Open Access Journals (Sweden)

Tilani Hamid

2010-10-01

Full Text Available Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio = 5 : 1, amount of NaOH used as catalyst = 3.5 gr, 4.5 gr, 5 gr and 5.5 gr and it takes about one hour time reaction. The ester (metil ester produced are separated from glycerin and washed until it takes normal pH (6-7 where more amount of catalyst used will decrease the ester (biodiesel produced. The results show that biodiesels' properties made by using 3.5 (M3.5 gr, 4.5 gr (M4.5 and 5 (M5.0 gr catalyst close to industrial diesel oil and the other (M5.5 closes to automotive diesel oil, while blending diesel oil with 20 % biodiesel (B20 is able to improve the diesel engine performances.

Phytic acid-stabilized super-amphiphilic Fe3O4-graphene oxide for extraction of polycyclic aromatic hydrocarbons from vegetable oils.

Science.gov (United States)

Ji, Wenhua; Zhang, Mingming; Duan, Wenjuan; Wang, Xiao; Zhao, Hengqiang; Guo, Lanping

2017-11-15

Phytic acid-stabilized Fe 3 O 4 -graphene oxide (GOPA@Fe 3 O 4 ) was assembled by microwave-enhanced hydrothermal synthesis and super-amphipathicity was demonstrated by measurement of dynamic oil and water contact angles. GOPA@Fe 3 O 4 was used as a sorbent for enrichment of eight polycyclic aromatic hydrocarbons (PAHs) from vegetable oils by magnetic solid-phase extraction (MSPE). The extraction-desorption factors were systematically investigated and, under optimum conditions, the super-amphiphilic sorbent achieved wide linear ranges (0.2-200ngg -1 ), satisfactory precision (3.44-6.64% for intra-day and 5.39-8.41% for inter-day) and low limits of detection (LODs, 0.06-0.15ngg -1 ) for PAHs. Excellent recoveries (85.6-102.3%) for spiked PAHs were obtained with genuine vegetable oil samples. These results indicate that MSPE using GOPA@Fe 3 O 4 as the sorbent, coupled with high performance liquid chromatography (HPLC), is an efficient and simple method for the detection of low concentrations of PAHs in vegetable oils. Copyright © 2017 Elsevier Ltd. All rights reserved.

Non Catalytic Transesterification of Vegetables Oil to Biodiesel in Sub-and Supercritical Methanol: A Kinetic’s Study

Directory of Open Access Journals (Sweden)

Nyoman Puspa Asri

2013-03-01

Full Text Available Non catalytic transesterification in sub and supercritical methanol have been used to produce biodiesel from palm oil and soybean oil. A kinetic study was done under reaction condition with temperature and time control. The experiments were carried out in a batch type reactor at reaction temperatures from 210 °C (subcritical condition to 290 °C (the supercritical state in the interval ranges of temperature of 20 °C and at various molar ratios of oil to methanol. The rate constants of the reaction were determined by employing a simple method, with the overall chemical reaction followed the pseudo-first–order reaction. Based on the results, the rate constants of vegetables oil were significantly influenced by reaction temperature, which were gradually increased at subcritical temperature, but sharply increased in the supercritical state. However, the rate constants of soybean oil were slightly higher than that of palm oil. The activation energy for transesterification of soybean oil was 89.32 and 79.05 kJ/mole for palm oil. Meanwhile, the frequency factor values of both oils were 72462892 and 391210 min-1, respectively. The rate reaction for both of oil were expressed as -rTG = 72462892 exp(-89.32/RTCTG for soybean oil and -rTG = 391210 exp(-79.05/RTCTG for palm oil. © 2013 BCREC UNDIP. All rights reservedReceived: 18th October 2012; Revised: 14th December 2012; Accepted: 16th December 2012[How to Cite: N.P. Asri, S. Machmudah, W. Wahyudiono, S. Suprapto, K. Budikarjono, A. Roesyadi, M. Goto, (2013. Non Catalytic Transesterification of Vegetables Oil to Biodiesel in Sub-and Supercritical Methanol: A Kinetic’s Study. Bulletin of Chemical Reaction Engineering & Catalysis, 7 (3: 215-223. (doi:10.9767/bcrec.7.3.4060.215-223][Permalink/DOI: http://dx.doi.org/10.9767/bcrec.7.3.4060.215-223 ] View in  |

Application of kaolin-based catalysts in biodiesel production via transesterification of vegetable oils in excess methanol.

Science.gov (United States)

Dang, Tan Hiep; Chen, Bing-Hung; Lee, Duu-Jong

2013-10-01

Biodiesel production from transesterification of vegetable oils in excess methanol was performed by using as-prepared catalyst from low-cost kaolin clay. This effective heterogeneous catalyst was successfully prepared from natural kaolin firstly by dehydroxylation at 800°C for 10h and, subsequently, by NaOH-activation hydrothermally at 90°C for 24h and calcined again at 500°C for 6h. The as-obtained catalytic material was characterized with instruments, including FT-IR, XRD, SEM, and porosimeter (BET/BJH analysis). The as-prepared catalyst was advantageous not only for its easy preparation, but also for its cost-efficiency and superior catalysis in transesterification of vegetable oils in excess methanol to produce fatty acid methyl esters (FAMEs). Conversion efficiencies of soybean and palm oils to biodiesel over the as-prepared catalysts reached 97.0±3.0% and 95.4±3.7%, respectively, under optimal conditions. Activation energies of transesterification reactions of soybean and palm oils in excess methanol using these catalysts are 14.09 kJ/mol and 48.87 kJ/mol, respectively. Copyright © 2012 Elsevier Ltd. All rights reserved.

Chromatography in authenticity and traceability tests of vegetable oils and dairy products: a review

Czech Academy of Sciences Publication Activity Database

Cserháti, T.; Forgács, E.; Deyl, Zdeněk; Mikšík, Ivan

2005-01-01

Roč. 19, č. 3 (2005), s. 183-190 ISSN 0269-3879 Grant - others:CZ-HU(CZ) Cooperation programme Institutional research plan: CEZ:AV0Z50110509 Keywords : chromatography * dairy products * vegetable oils Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 1.218, year: 2005

Soybean plant-based toxicity assessment and phytoremediation of soils contaminated by vegetable and mineral oils used in power electrical transformers.

Science.gov (United States)

Sanderson, Karina; Módenes, Aparecido Nivaldo; Espinoza-Quiñones, Fernando Rodolfo; Trigueros, Daniela Estelita Goes; Júnior, Luiz Antônio Zanão; Schuelter, Adilson Ricken; Neves, Camila Vargas; Kroumov, Alexander Dimitrov

2018-04-01

In this work, deleterious effects in soils due to the presence of dielectric fluids were investigated. For this purpose, vegetable (Envirotemp ® FR3) and mineral (Lubrax AV 66 IN) oils were used for simulating a set of soils contaminated in different oil contents (0.5, 1.0, 2.0, 2.5, 5.0, 7.5 and 10%) in which three 120-days soybean crop periods (SCP) were carried out using the species Glycine max (L.) Merr. Both soil and soybean plant samples were analysed on following the changes on chemical attributes, content of oils and greases (COG) in soils and phytotechnical characteristics of soybean plant. No significant changes on soil chemical attributes were found. For a 0.5% vegetable oil fraction, COG removals of 35, 60 and 90% were observed after the 1st, 2nd, and 3rd SCPs, respectively, whereas removals of 25, 40 and 70% were observed for 0.5% mineral oil fraction after the 1st, 2nd, and 3rd SCPs, respectively. There was an effectively accumulated removal on all tested oil fractions as being proportional to the integrated 120-days SCPs, suggesting a lesser number of crops for a complete abatement of oil fraction in soil. A 100% recovery on the seedlings emergence fractions was also evidenced, revealing that at least a number of 7 and 9 SCPs should be applied continuously in soils contaminated by vegetable and mineral oils, respectively, in order to no longer jeopardize soybean plant growth. Finally, an empirical prediction of the number of SCPs necessary for the complete removal of oil from the soil was proposed. Copyright © 2018 Elsevier Ltd. All rights reserved.

Comparative study of oxidation in canned foods with a combination of vegetables and covering oils

OpenAIRE

E. Bravi; A. Mangione; O. Marconi; G. Perretti

2015-01-01

The effects of sunflower (SFO), extra-virgin olive (EVO), and soybean oils (SBO), in combination with canned aubergins and dried tomatoes were studied during an accelerated shelf-life trial. Hydrolytic and oxidative quality parameters was determined and a sensorial test was run. For both canned vegetables, the SBO showed greater resistance to the oxidation at the end of the shelflife trial. The SBO in both vegetables yielded similar results for peroxide formation, whereas a reduced formation ...

Effect of agricultural inputs and essential oils on the soil of vegetables in Colombia's Caribbean region

Directory of Open Access Journals (Sweden)

Eduardo Mena-Rodríguez

2018-01-01

Full Text Available The contribution of vegetables to food security and economic development in Colombia, as well as to environmental problems worldwide, justifies the interest to design sustainable production strategies for the agro-chain. This study was developed to evaluate the effect of the application of essential oils and agricultural inputs in chili peppers, beans and eggplants in Codazzi, Cesar, Colombia. The methodology included the compatibility analysis between pesticides used in these vegetables, and Lippia alba and Cymbopogon citratus oils in relation to their biocidal effect in vitro on native strains of Macrophomina phaseolina, Phytophthora capsici and Colletotrichum gloeosporioides. Applications of thiabendazole in an individual basis and combined with oils were carried out in the field. Physicochemical and microbiological indicators of soil, pests and diseases incidence and crop yield were measured. Oils controlled up to 97% of plant pathogens in vitro and exhibited compatibility with carbendazim and thiabendazole. In the field, up to 67 % of disease control was observed with C. citratus + thiabendazole compared to the control (p = 0.00, yields were close to the regional average, and better microbiological and physicochemical soil conditions were observed. In conclusion, there are differences in the edaphic effect between treatments, as the agrochemical and the oil combinations were more favorable than the individual effect of each product on the variables evaluated. The above exhorts to continue soil evaluations with oils to elucidate the duration of the described effects.

Optical methods and differential scanning calorimetry as a potential tool for discrimination of olive oils (extra virgin and mix with vegetable oils)

Science.gov (United States)

Nikolova, Kr.; Yovcheva, T.; Marudova, M.; Eftimov, T.; Bodurov, I.; Viraneva, A.; Vlaeva, I.

2016-03-01

Eleven samples from olive oil have been investigated using four physical methods - refractive index measurement, fluorescence spectra, color parameters and differential scanning colorimetry. In pomace olive oil (POO) and extra virgin olive oil (EVOO) the oleic acid (65.24 %-78.40 %) predominates over palmitic (10.47 %-15.07 %) and linoleic (5.26 %-13.92 %) acids. The fluorescence spectra contain three peaks related to oxidation products at about λ = (500-540) nm, chlorophyll content at about λ = (675-680) nm and non determined pigments at λ = (700-750) nm. The melting point for EVOO and POO is between -1 °C and -6 °C. In contrast, the salad olive oils melt between -24 °C and -30 °C. The refractive index for EVOO is lower than that for mixed olive oils. The proposed physical methods could be used for fast and simple detection of vegetable oils in EVOO without use of chemical substances. The experimental results are in accordance with those obtained by chemical analysis.

Essential Oils: Sources of Antimicrobials and Food Preservatives

Science.gov (United States)

Pandey, Abhay K.; Kumar, Pradeep; Singh, Pooja; Tripathi, Nijendra N.; Bajpai, Vivek K.

2017-01-01

Aromatic and medicinal plants produce essential oils in the form of secondary metabolites. These essential oils can be used in diverse applications in food, perfume, and cosmetic industries. The use of essential oils as antimicrobials and food preservative agents is of concern because of several reported side effects of synthetic oils. Essential oils have the potential to be used as a food preservative for cereals, grains, pulses, fruits, and vegetables. In this review, we briefly describe the results in relevant literature and summarize the uses of essential oils with special emphasis on their antibacterial, bactericidal, antifungal, fungicidal, and food preservative properties. Essential oils have pronounced antimicrobial and food preservative properties because they consist of a variety of active constituents (e.g., terpenes, terpenoids, carotenoids, coumarins, curcumins) that have great significance in the food industry. Thus, the various properties of essential oils offer the possibility of using natural, safe, eco-friendly, cost-effective, renewable, and easily biodegradable antimicrobials for food commodity preservation in the near future. PMID:28138324

In-vial liquid-liquid microextraction-capillary electrophoresis method for the determination of phenolic acids in vegetable oils.

Science.gov (United States)

Abu Bakar, Nur Bahiyah; Makahleh, Ahmad; Saad, Bahruddin

2012-09-12

An in-vial liquid-liquid microextraction method was developed for the selective extraction of the phenolic acids (caffeic, gallic, cinnamic, ferulic, chlorogenic, syringic, vanillic, benzoic, p-hydroxybenzoic, 2,4-dihydroxybenzoic, o-coumaric, m-coumaric and p-coumaric) in vegetable oil samples. The optimised extraction conditions for 20 g sample were: volume of diluent (n-hexane), 2 mL; extractant, methanol: 5 mM sodium hydroxide (60:40; v/v); volume of extractant, 300 μL (twice); vortex, 1 min; centrifugation, 5 min. Recoveries for the studied phenolic acids were 80.1-119.5%. The simultaneous determination of the phenolic acid extracts was investigated by capillary electrophoresis (CE). Separations were carried out on a bare fused-silica capillary (50 μm i.d.× 40 cm length) involving 25 mM sodium tetraborate (pH 9.15) and 5% methanol as CE background electrolyte in the normal polarity mode, voltage of 30 kV, temperature of 25°C, injection time of 4s (50 mbar) and electropherograms were recorded at 200 nm. The phenolic acids were successfully separated in less than 10 min. The validated in-vial LLME-CE method was applied to the determination of phenolic acids in vegetable oil samples (extra virgin olive oil, virgin olive oil, pure olive oil, walnut oil and grapeseed oil). The developed method shows significant advantages over the current methods as lengthy evaporation step is not required. Copyright © 2012 Elsevier B.V. All rights reserved.

The Influence of Different Vegetable Oils on Some ω-3 Polyunsaturated Fatty Acids in Broiler Chickens Breast

Directory of Open Access Journals (Sweden)

Dragoş-Sorin Fota

2011-05-01

Full Text Available Taking into consideration that the vegetable oils added to the combined fodder can significantly modify the fatty acids profile in broiler food, through its redirection even the fatty acids profile of carcasses can be modified through enrichment in certain fatty acids and obtaining functional foods. Therefore an experiment was conduced on broilers, made up of three experimental groups, fed with a combined base fodder in which 2% of different fat sources have been incorporated (sunflower oil, soybean oil, linseed oil. After the 42 days growth period, the fatty acids profile, % of fatty acids in 100 g product (EPA, DPA, DHA, ∑ SFA, ∑ MUFA, ∑ PUFA of the chicken from the experimental groups, were determined. Fatty acids were determined using gascromatography. The data obtained after statistic processing and interpretation have highlighted the fact that, concerning the fatty acids profile in the chickens breast, we can observe variations of the determined fatty acids content, what shows us that they can be influenced through dietary factors, but there quantity being determined by the participation % of the energy sources (vegetable oils, but also by the fatty acids content of the participating raw materials.

Analysis of glycolipids in vegetable lecithin with HPLC-ELSD

OpenAIRE

Nguyen Tuyet, Mai; De Vrieze, Mike; Van de Walle, Davy; Van Hoed, Vera; Lynen, Frederic; Dewettinck, Koen

2014-01-01

Vegetable lecithins play an important role in the microstructural and macroscopic properties of food and cosmetic products. They are widely used as a natural emulsifier. As lecithin is a by-product of the vegetable oil refining industry, its composition is quite variable and rather complex. Therefore, a more complete view on the chemical composition of lecithin would assist in elucidating its functionality. This study focused on the separation and quantification of several glycolipid...

Phenols and the antioxidant capacity of Mediterranean vegetables prepared with extra virgin olive oil using different domestic cooking techniques.

Science.gov (United States)

Ramírez-Anaya, Jessica Del Pilar; Samaniego-Sánchez, Cristina; Castañeda-Saucedo, Ma Claudia; Villalón-Mir, Marina; de la Serrana, Herminia López-García

2015-12-01

Potato, tomato, eggplant and pumpkin were deep fried, sautéed and boiled in Mediterranean extra virgin olive oil (EVOO), water, and a water/oil mixture (W/O). We determined the contents of fat, moisture, total phenols (TPC) and eighteen phenolic compounds, as well as antioxidant capacity in the raw vegetables and compared these with contents measured after cooking. Deep frying and sautéing led to increased fat contents and TPC, whereas both types of boiling (in water and W/O) reduced the same. The presence of EVOO in cooking increased the phenolics identified in the raw foods as oleuropein, pinoresinol, hydroxytyrosol and tyrosol, and the contents of vegetable phenolics such as chlorogenic acid and rutin. All the cooking methods conserved or increased the antioxidant capacity measured by DPPH, FRAP and ABTS. Multivariate analyses showed that each cooked vegetable developed specific phenolic and antioxidant activity profiles resulting from the characteristics of the raw vegetables and the cooking techniques. Copyright © 2015 Elsevier Ltd. All rights reserved.

Some basic properties of environmentally adapted oils

Energy Technology Data Exchange (ETDEWEB)

Hoeglund, E. [Div. of Machine Elements, Luleaa University of Technology (Sweden)

1998-11-01

Environmental concern has led to a development of lubricants that are less harmful to the environmental than traditional mineral based oils. Biodegradability and non-toxicity are desired properties together with a competitive price and if possible they should also be derived from renewable raw materials. In order to have a major breakthrough for the new, environmentally adapted lubricating oils they must perform well in mechanical and hydraulic systems. They must reduce wear, increase efficiency and reduce maintenance costs equally well, or preferably better than mineral based oils. This paper presents primary results from an investigation where four environmentally adapted oils (rape seed, pine tree, diester and TMP-ester) are compared to a conventional naphthenic mineral oil. Viscosity and viscosity-pressure coefficients, limiting shear stress, friction properties and film forming ability have been evaluated under elastohydrodynamic conditions. It was found that the mineral oil had the highest values of pressure-viscosity coefficient, limiting shear stress and coefficient of friction. Rape seed oil had the second highest pressure-viscosity coefficient but the lowest limiting shear stress and coefficient of friction. Pine tree oil, diester and TMP-ester formed an intermediate group with rather similar results. The Hamrock-Dowson equation for central film thickness was found to overestimate film thickness by about 10-20 per cent with the least discrepancy for the mineral oil. (orig.) 8 refs.

Testing the ecotoxicology of vegetable versus mineral based lubricating oils: 2. Induction of mixed function oxidase enzymes in barramundi, Lates calcarifer, a tropical fish species

International Nuclear Information System (INIS)

Mercurio, Philip; Burns, Kathryn A.; Cavanagh, Joanne

2004-01-01

An increasing number of vegetable-based oils are being developed as environmentally friendly alternatives to petroleum products. However, toxicity towards key tropical marine species has not been investigated. In this study we used laboratory-based biomarker induction experiments to compare the relative stress of a vegetable-based lubricating oil for marine 2-stroke engines with its mineral oil-based counterpart on tropical fish. The sub-lethal stress of 2-stoke outboard lubricating oils towards the fish Lates calcarifer (barramundi) was examined using liver microsomal mixed function oxidase (MFO) induction assays. This study is the first investigation into the use of this key commercial species in tropical North Queensland, Australia in stress assessment of potential hydrocarbon pollution using ethoxyresorufin O-deethylase (EROD) induction. Our results indicated that barramundi provide a wide range of inducible rates of EROD activity in response to relevant organic stressors. The vegetable- and mineral-based lubricants induced significant EROD activity at 1.0 mg kg -1 and there was no significant difference between the two oil treatments at that concentration. At increasing concentrations of 2 and 3 mg kg -1 , the mineral-based lubricant resulted in slightly higher EROD activity than the vegetable-based lubricant. The EROD activity of control and treated barramundi are found to be within ranges for other species from temperate and tropical environments. These results indicate that vegetable-based lubricants may be less stressful to barramundi than their mineral counterparts at concentrations of lubricant ≥2 mg kg -1 . There is great potential for this species to be used in the biomonitoring of waterways around tropical North Queensland and SE Asia. - Vegetable-based lubricating oils appear to cause a tropical fish species less stress than mineral oils

Testing the ecotoxicology of vegetable versus mineral based lubricating oils: 2. Induction of mixed function oxidase enzymes in barramundi, Lates calcarifer, a tropical fish species

Energy Technology Data Exchange (ETDEWEB)

Mercurio, Philip; Burns, Kathryn A.; Cavanagh, Joanne

2004-05-01

An increasing number of vegetable-based oils are being developed as environmentally friendly alternatives to petroleum products. However, toxicity towards key tropical marine species has not been investigated. In this study we used laboratory-based biomarker induction experiments to compare the relative stress of a vegetable-based lubricating oil for marine 2-stroke engines with its mineral oil-based counterpart on tropical fish. The sub-lethal stress of 2-stoke outboard lubricating oils towards the fish Lates calcarifer (barramundi) was examined using liver microsomal mixed function oxidase (MFO) induction assays. This study is the first investigation into the use of this key commercial species in tropical North Queensland, Australia in stress assessment of potential hydrocarbon pollution using ethoxyresorufin O-deethylase (EROD) induction. Our results indicated that barramundi provide a wide range of inducible rates of EROD activity in response to relevant organic stressors. The vegetable- and mineral-based lubricants induced significant EROD activity at 1.0 mg kg{sup -1} and there was no significant difference between the two oil treatments at that concentration. At increasing concentrations of 2 and 3 mg kg{sup -1}, the mineral-based lubricant resulted in slightly higher EROD activity than the vegetable-based lubricant. The EROD activity of control and treated barramundi are found to be within ranges for other species from temperate and tropical environments. These results indicate that vegetable-based lubricants may be less stressful to barramundi than their mineral counterparts at concentrations of lubricant {>=}2 mg kg{sup -1}. There is great potential for this species to be used in the biomonitoring of waterways around tropical North Queensland and SE Asia. - Vegetable-based lubricating oils appear to cause a tropical fish species less stress than mineral oils.

Influence of High Temperature and Duration of Heating on the Sunflower Seed Oil Properties for Food Use and Bio-diesel Production.

Science.gov (United States)

Giuffrè, Angelo Maria; Capocasale, Marco; Zappia, Clotilde; Poiana, Marco

2017-01-01

Two important problems for the food industry are oil oxidation and oil waste after frying. Sunflower seed oil is one of the vegetable oils most commonly used in the food industry. Two variables were applied to the low oleic sunflower seed oil in this work i.e. heating temperature (180-210-240°C) and time of heating (15-30-60-120 minutes), to study from the edible point of view the variations of its physico-chemical properties. After 120 minutes heating at 240°C the following was found: refractive index (1.476), free acidity (0.35%), K232 (2.87), K270 (3.71), antiradical activity (45.90% inhibition), total phenols (523 mg kg -1 ), peroxide value (17.00 meq kg -1 ), p-anisidine value (256.8) and Totox (271.7), all of which showed a constant deterioration. In relation to the use as a feedstock for bio-diesel production, after 120 minutes heating at 240℃ the following was found: acid value 0.70 mg KOH g -1 oil, iodine value 117.83 g I 2 100 g -1 oil, oil stability index 0.67 h, kinematic viscosity (at 40°C) 77.85 mm 2 s -1 , higher heating value 39.86 MJ kg -1 , density 933.34 kg/m 3 and cetane number 67.04. The parameters studied in this work were influenced, in different ways, by the applied variables. Heating temperature between 180 and 210°C and 120 min heating duration were found to be the most appropriate conditions for sunflower seed oil both from the deep frying point of view and from a subsequent use as feedstock for bio-diesel production. In light of the vegetable oils' International standards for an edible use and for a bio-diesel production, findings of this work can be used to set heating temperature and heating duration to preserve as long possible the physico-chemical properties of a low oleic sunflower seed oil for both its edible use as a fat during cooking and for its re-use after frying.

Remediation of trichloroethylene-contaminated soils by star technology using vegetable oil smoldering

OpenAIRE

Salman, Madiha; Gerhard, Jason I.; Major, David W.; Pironi, Paolo; Hadden, Rory

2015-01-01

Self-sustaining treatment for active remediation (STAR) is an innovative soil remediation approach based on smoldering combustion that has been demonstrated to effectively destroy complex hydrocarbon nonaqueous phase liquids (NAPLs) with minimal energy input. This is the first study to explore the smoldering remediation of sand contaminated by a volatile NAPL (trichloroethylene, TCE) and the first to consider utilizing vegetable oil as supplemental fuel for STAR. Thirty laboratory-scale exper...

Influence of non-edible vegetable based oil as cutting fluid on chip, surface roughness and cutting force during drilling operation of Mild Steel

Science.gov (United States)

Susmitha, M.; Sharan, P.; Jyothi, P. N.

2016-09-01

Friction between work piece-cutting tool-chip generates heat in the machining zone. The heat generated reduces the tool life, increases surface roughness and decreases the dimensional sensitiveness of work material. This can be overcome by using cutting fluids during machining. They are used to provide lubrication and cooling effects between cutting tool and work piece and cutting tool and chip during machining operation. As a result, important benefits would be achieved such longer tool life, easy chip flow and higher machining quality in the machining processes. Non-edible vegetable oils have received considerable research attention in the last decades owing to their remarkable improved tribological characteristics and due to increasing attention to environmental issues, have driven the lubricant industry toward eco friendly products from renewable sources. In the present work, different non-edible vegetable oils are used as cutting fluid during drilling of Mild steel work piece. Non-edible vegetable oils, used are Karanja oil (Honge), Neem oil and blend of these two oils. The effect of these cutting fluids on chip formation, surface roughness and cutting force are investigated and the results obtained are compared with results obtained with petroleum based cutting fluids and dry conditions.

Stability of traditionally processed vegetable oils and their blends ...

African Journals Online (AJOL)

physicochemical properties which included acid value, saponification value, peroxide value, iodine ... The oils and their blends were stored in two different conditions; one batch at the air-tight .... about 0.5 ml of starch indicator solution was.

Evaluation of the use of a vegetable oil in distribution transformers Evaluación del uso de un aceite vegetal en transformadores de distribución

Directory of Open Access Journals (Sweden)

Diego Fernando-Navas

2012-08-01

Full Text Available Since the start of transformers immersed in refrigerating liquid, the fluid traditionally used has been mineral oil. However, in recent decades, efforts have been joined in the search for alternatives with a lower environmental impact and which also satisfy the technical requirements of insulation and refrigeration in the transformers. Currently, insulating vegetable oils are available in the market, which may have lower environmental impact during their use and final disposition; nevertheless, their high cost and short time of use have limited their massive application. This work presents the thermal behavior evaluation of two distribution transformers at different powers immersed in dielectric vegetable oil, comparing their performance with that of two constructively equal transformers immersed in mineral oil. The results obtained reveal that the transformers comply with the requirements of existing standards.Desde los inicios de los transformadores inmersos en líquido refrigerante, el fluido empleado por tradición ha sido el aceite de origen mineral. Sin embargo, en las últimas décadas se han unido esfuerzos en la búsqueda de alternativas que tengan un menor impacto en el medio ambiente y que a su vez satisfagan los requerimientos técnicos de aislamiento y refrigeración en los transformadores. Actualmente se encuentran en el mercado aceites aislantes de origen vegetal que pueden tener un menor impacto ambiental durante su uso y disposición final; no obstante, su elevado costo y su poco tiempo de uso han limitado su aplicación masiva. En este trabajo se presenta la evaluación del comportamiento térmico de dos transformadores de distribución de diferente potencia inmersos en aceite dieléctrico de origen vegetal y se compara su desempeño con el de dos transformadores constructivamente iguales inmersos en aceite mineral. Los resultados obtenidos revelan que los transformadores cumplen con los requerimientos de la normatividad

Methyl Ester (Bio diesel) Production from Waste Cooking Vegetable Oil by Microwave Irradiation

International Nuclear Information System (INIS)

Khatun, M.S.; Khatun, M.A.; Khan, M.Z.H.; Debnath, M.

2014-01-01

In this study we tried to develop, test and optimize a batch microwave system using waste cooking vegetable oil (WCVO) that was used as bio diesel feedstock. Two catalysts, sodium hydroxide (NaOH) and potassium hydroxide (KOH) were tested in this study. Transesterification reactions between oil and methanol were carried out in presence of microwaves. It was observed that by using of microwaves, the reaction times were drastically reduced. As high as 99.5 % conversions could be achieved for 0.5% KOH concentration. Moreover, quality analysis of bio diesels according to international standards was performed and the samples were found to meet the necessary specifications. (author)

Effects of Replacing Pork Back Fat with Canola and Flaxseed Oils on Physicochemical Properties of Emulsion Sausages from Spent Layer Meat

Directory of Open Access Journals (Sweden)

Ki Ho Baek

2016-06-01

Full Text Available The objective of this study was to investigate the effects of canola and flaxseed oils on the physicochemical properties and sensory quality of emulsion-type sausage made from spent layer meat. Three types of sausage were manufactured with different fat sources: 20% pork back fat (CON, 20% canola oil (CA and 20% flaxseed oil (FL. The pH value of the CA was significantly higher than the others (p<0.05. The highest water holding capacity was also presented for CA; in other words, CA demonstrated a significantly lower water loss value among the treatments (p<0.05. CA had the highest lightness value (p<0.05. However, FL showed the highest yellowness value (p<0.05 because of its own high-density yellow color. The texture profile of the treatments manufactured with vegetable oils showed higher values than for the CON (p<0.05; furthermore, CA had the highest texture profile values (p<0.05 among the treatments. The replacement of pork back fat with canola and flaxseed oils in sausages significantly increased the omega-3 fatty acid content (p<0.05 over 15 to 86 times, respectively. All emulsion sausages containing vegetable oil exhibited significantly lower values for saturated fatty acid content and the omega-6 to omega-3 ratios compared to CON (p<0.05. The results show that using canola or flaxseed oils as a pork fat replacer has a high potential to produce healthier products, and notably, the use of canola oil produced characteristics of great emulsion stability and sensory quality.

Effects of Replacing Pork Back Fat with Canola and Flaxseed Oils on Physicochemical Properties of Emulsion Sausages from Spent Layer Meat.

Science.gov (United States)

Baek, Ki Ho; Utama, Dicky Tri; Lee, Seung Gyu; An, Byoung Ki; Lee, Sung Ki

2016-06-01

The objective of this study was to investigate the effects of canola and flaxseed oils on the physicochemical properties and sensory quality of emulsion-type sausage made from spent layer meat. Three types of sausage were manufactured with different fat sources: 20% pork back fat (CON), 20% canola oil (CA) and 20% flaxseed oil (FL). The pH value of the CA was significantly higher than the others (p<0.05). The highest water holding capacity was also presented for CA; in other words, CA demonstrated a significantly lower water loss value among the treatments (p<0.05). CA had the highest lightness value (p<0.05). However, FL showed the highest yellowness value (p<0.05) because of its own high-density yellow color. The texture profile of the treatments manufactured with vegetable oils showed higher values than for the CON (p<0.05); furthermore, CA had the highest texture profile values (p<0.05) among the treatments. The replacement of pork back fat with canola and flaxseed oils in sausages significantly increased the omega-3 fatty acid content (p<0.05) over 15 to 86 times, respectively. All emulsion sausages containing vegetable oil exhibited significantly lower values for saturated fatty acid content and the omega-6 to omega-3 ratios compared to CON (p<0.05). The results show that using canola or flaxseed oils as a pork fat replacer has a high potential to produce healthier products, and notably, the use of canola oil produced characteristics of great emulsion stability and sensory quality.

Effect of the addition of fatty by-products from the refining of vegetable oil on methane production in co-digestion.

Science.gov (United States)

Torrijos, M; Sousbie, P; Badey, L; Bosque, F; Steyer, J P

2012-01-01

The purpose of this work was to investigate the effects of the addition of by-products from the refining of vegetable oil on the behavior of co-digestion reactors treating a mixture of grass, cow dung and fruit and vegetable waste. Three by-products were used: one soapstock, one used winterization earth and one skimming of aeroflotation of the effluents. Three 15 l reactors were run in parallel and fed five times a week. In a first phase of 4 weeks, the three reactors were fed with the co-digestion substrates alone (grass, cow dung and fruit and vegetable waste) at an organic loading rate (OLR) of 1.5 g VS/kg d (VS: volatile solids). Then, a different by-product from the refining of oil was added to the feed of each reactor at an OLR of 0.5 g VS/kg d, generating a 33% increase in the OLR. The results show that the addition of by-products from the refining of oil is an efficient way of increasing the methane production of co-digestion reactors thanks to high methane yield of such by-products (0.69-0.77 l CH(4)/g VS loaded). In fact, in this work, it was possible to raise the methane production of the reactors by about 60% through a 33% increase in the OLR thanks to the addition of the by-products from the refining of vegetable oil.

TRANSESTERIFICATION OF VEGETABLES OIL USING SUBAND SUPERCRITICAL METHANOL

Directory of Open Access Journals (Sweden)

Nyoman Puspa Asri

2012-11-01

Full Text Available A benign process, non catalytic transesterification in sub and supercritical methanol method was usedto prepare biodiesel from vegetables oil. The experiment was carried out in batch type reactor (8.8 mlcapacity, stainless steel, AKICO, JAPAN by changing the reaction condition such as reactiontemperature (from 210°C in subcritical condition to 290°C in supercritical state with of 20°Cinterval, molar ratio oil to methanol (1:12-1:42 and time of reaction (10-90 min. The fatty acidmethyl esters (FAMEs content was analyzed by gas chromatography-flame ionization detector (GCFID.Such analysis can be used to determine the biodiesel yield of the transesterification. The resultsshowed that the yield of biodiesel increases gradually with the increasing of reaction time atsubcritical state (210-230oC. However, it was drastically increased at the supercritical state (270-290oC. Similarly, the yield of biodiesel sharply increased with increasing the ratio molar of soy oilmethanolup to 1:24. The maximum yield 86 and 88% were achieved at 290oC, 90 min of reaction timeand molar ratio of oil to methanol 1:24, for soybean oil and palm oil, respectively.Proses transesterifikasi non katalitik dengan metanol sub dan superkritis,merupakan proses yang ramah lingkungan digunakan untuk pembuatan biodiesel dari minyak nabati.Percobaan dilakukan dalam sebuah reaktor batch (kapasitas 8,8 ml, stainless steel, AKICO, JAPAN,dengan variabel kondisi reaksi seperti temperatur reaksi (dari kondisi subkritis 210°C-kondisisuperkritis 290°C dengan interval 20°C, rasio molar minyak-metanol (1:12-1:42 dan waktu reaksi(10-90 menit. Kandungan metil ester asam lemak (FAME dianalisis dengan kromatografi gasdengan detektor FID (GC-FID. Hasil Analisis tersebut dapat digunakan untuk menentukan yieldbiodiesel dari proses transesterifikasi. Hasil penelitian menunjukkan bahwa yield biodiesel meningkatsecara perlahan dengan meningkatnya waktu reaksi pada keadaan subkritis (210-230oC. Namun

Emulsion of systems containing egg yolk, polysaccharides and vegetable oil Emulsão de sistemas contendo gema de ovo, polissacarídeos e óleo vegetal

Directory of Open Access Journals (Sweden)

Clitor Junior Fernandes de Souza

2012-10-01

Full Text Available This work characterizes the emulsifying properties of systems containing egg yolk (0.1; 1.0 and 2.5 % w/v and polysaccharides (xanthan gum, carrageen, pectin and carboxymethylcellulose and three different vegetable oils (sunflower, canola, and palm oils. Emulsifying activity and emulsion stability were measured of each combination and it was found the effect of the oil on emulsion stability correlated to the amount of monounsaturated fatty acid. Additionally, increased egg yolk concentration increased emulsifying activity by reducing coalescence of oil droplets. Lastly, 2.5% egg yolk and 0.2% polysaccharide generated emulsions with high emulsifying activity, excellent stability, and droplet size of 4.32 µm.Neste trabalho, caracterizam-se as propriedades emulsificantes de sistemas contendo gema de ovo (0,1; 1,0 e 2,5% m/v, polissacarídeos (goma xantana, carragena, pectina e carboximetilcelulose e três diferentes óleos vegetais (óleos de palma, canola e girassol. Atividade emulsificante e estabilidade da emulsão foram medidas para cada combinação e verificou-se o efeito do óleo sobre a estabilidade da emulsão correlacionada com a quantidade de ácido graxo monoinsaturado. Além disso, a concentração de gema de ovo aumentou a atividade emulsificante, reduzindo a coalescência das gotículas de óleo. Por último, 2,5 % de gema de ovo e 0,2% de polissacarídeo formaram emulsões com alta atividade emulsificante, excelente estabilidade e tamanho de gota de 4,32 µm.

Evaluation of used vegetable oil for biogas production in Spain; Evaluacion del potencial de aceite vegetal usado para la obtencion de biogasoleo en la Comunidad de Castilla y Leon

Energy Technology Data Exchange (ETDEWEB)

Antolin, G.; Tinaut, F. V.; Saez, A. R.; Vegas, L.; Briceno, Y. [Universidad de Valladolid (Spain)

2002-07-01

This work studies the potential of the residual vegetal oil that is generated in the Community of Castilla and Leon, evaluating the one that could be destined for the production of biogas. Also, it sets out a management model that will allow to establish a suitable collection and processing of this oil. (Author) 10 refs.

Instantaneous Characterization Of Vegetable Oils Via Tag And Ffa Profiles By Easy Ambient Sonic-spray Ionization Mass Spectrometry.

OpenAIRE

Simas, Rosineide C; Catharino, Rodrigo R; Cunha, Ildenize B S; Cabral, Elaine C; Barrera-Arellano, Daniel; Eberlin, Marcos N; Alberici, Rosana M

2015-01-01

A fast and reliable method is presented for the analysis of vegetable oils. Easy ambient sonic-spray ionization mass spectrometry (EASI-MS) is shown to efficiently desorb and ionize the main oil constituents from an inert surface under ambient conditions and to provide comprehensive triacylglyceride (TAG) and free fatty acid (FFA) profiles detected mainly as either [TAG + Na](+) or [FFA-H](-) ions. EASI(+/-)-MS analysis is simple, easily implemented, requires just a tiny droplet of the oil an...

THEORETICAL MODELLING STUDY ON THE RELATIONSHIP BETWEEN MULTI-FREQUENCY MICROWAVE VEGETATION INDEX AND VEGETATION PROPERTIES (OPTICAL DEPTH AND SINGLE SCATTERING ALBEDO

Directory of Open Access Journals (Sweden)

S. Talebi

2018-04-01

Full Text Available This paper presents a theoretical study of derivation Microwave Vegetation Indices (MVIs in different pairs of frequencies using two methods. In the first method calculating MVI in different frequencies based on Matrix Doubling Model (to take in to account multi scattering effects has been done and analyzed in various soil properties. The second method was based on MVI theoretical basis and its independency to underlying soil surface signals. Comparing the results from two methods with vegetation properties (single scattering albedo and optical depth indicated partial correlation between MVI from first method and optical depth, and full correlation between MVI from second method and vegetation properties. The second method to derive MVI can be used widely in global microwave vegetation monitoring.

Comparative Studies on Some Physicochemical Properties of ...

African Journals Online (AJOL)

Industrial and nutritional processes have increased the demands for oil and this in turn has led to the search for oils from different types of seeds. It is in this vein that baobab seed oil was extracted, analyzed and some of it physicochemical properties compared with those of vegetable, peanut and palm oils. The percentage ...

Accounting for co-products in energy use, greenhouse gas emission savings and land use of biodiesel production from vegetable oils

NARCIS (Netherlands)

Corré, W.J.; Conijn, J.G.; Meesters, K.P.H.; Bos, H.L.

2016-01-01

Accounting for co-products of vegetable oil production is essential in reviewing the sustainability of biodiesel production, especially since oil crops produce valuable protein-rich co-products in different quantities and qualities. Two accounting methods, allocation on the basis of energy

Liquid Bio fuels: Vegetable Oils and Bi oethanol

International Nuclear Information System (INIS)

Ballesteros, M.; Ballesteros, I.; Oliva, J. M.; Navarro, A. A.

1998-01-01

The European energy policy has defined clear objectives to reduce the high dependency on fossil petroleum imports, and to increase the security of sustainable energy supply for the transport sector. Moreover, the European environmental policy is requesting clean fuels that reduce environmental risks. Liquid Bio fuels (vegetable oils and bio ethanol) appear to be in a good position to contribute to achieve these goals expressed by the established objective of European Union to reach for bio fuels a market share of 5% of motor vehicle consumption. This work presents the current state and perspectives of the production and utilisation of liquid fuels from agricultural sources by reviewing agricultural feedstocks for energy sector, conversion technologies and different ways to use bio fuels. Environmental and economical aspects are also briefly analysed. (Author) 10 refs