WorldWideScience

Sample records for varying initial conditions

  1. Initial Cladding Condition

    International Nuclear Information System (INIS)

    Siegmann, E.

    2000-01-01

    The purpose of this analysis is to describe the condition of commercial Zircaloy clad fuel as it is received at the Yucca Mountain Project (YMP) site. Most commercial nuclear fuel is encased in Zircaloy cladding. This analysis is developed to describe cladding degradation from the expected failure modes. This includes reactor operation impacts including incipient failures, potential degradation after reactor operation during spent fuel storage in pool and dry storage and impacts due to transportation. Degradation modes include cladding creep, and delayed hydride cracking during dry storage and transportation. Mechanical stresses from fuel handling and transportation vibrations are also included. This Analysis and Model Report (AMR) does not address any potential damage to assemblies that might occur at the YMP surface facilities. Ranges and uncertainties have been defined. This analysis will be the initial boundary condition for the analysis of cladding degradation inside the repository. In accordance with AP-2.13Q, ''Technical Product Development Planning'', a work plan (CRWMS M andO 2000c) was developed, issued, and utilized in the preparation of this document. There are constraints, caveats and limitations to this analysis. This cladding degradation analysis is based on commercial Pressurized Water Reactor (PWR) fuel with Zircaloy cladding but is applicable to Boiling Water Reactor (BWR) fuel. Reactor operating experience for both PWRs and BWRs is used to establish fuel reliability from reactor operation. It is limited to fuel exposed to normal operation and anticipated operational occurrences (i.e. events which are anticipated to occur within a reactor lifetime), and not to fuel that has been exposed to severe accidents. Fuel burnup projections have been limited to the current commercial reactor licensing environment with restrictions on fuel enrichment, oxide coating thickness and rod plenum pressures. The information provided in this analysis will be used in

  2. Initial conditions for chaotic inflation

    International Nuclear Information System (INIS)

    Brandenberger, R.; Kung, J.; Feldman, H.

    1991-01-01

    In contrast to many other inflationary Universe models, chaotic inflation does not depend on fine tuning initial conditions. Within the context of linear perturbation theory, it is shown that chaotic inflation is stable towards both metric and matter perturbations. Neglecting gravitational perturbations, it is shown that chaotic inflation is an attractor in initial condition space. (orig.)

  3. Inflation with generalized initial conditions

    International Nuclear Information System (INIS)

    Albrecht, A.; Brandenberger, R.; Matzner, R.

    1987-01-01

    In many current models of the early Universe a scalar field phi which is only very weakly coupled to other quantum fields is used to generate inflation. In such models there are no forces which could thermalize the scalar field, and previous assumptions about its preinflation ''initial'' conditions must be abandoned. In this paper the onset of inflation is studied classically for more general initial conditions of the scalar field configuration. In particular, initial conditions with a nonvanishing spatial average of phi, with phi chosen at random in each initial horizon volume, and with random initial momenta are considered. We identify and discuss several mechanisms that can drive these more general initial conditions toward an inflationary state. The analysis is done in one spatial dimension

  4. Panorama 2011: Refining: varying conditions by region

    International Nuclear Information System (INIS)

    Silva, C.

    2011-01-01

    The economic crisis has further weakened a sector that was already facing difficulties, if we look beyond the flush period (2005-2008) when, buoyed by strong demand, margins remained high and refiners could generate profits while maintaining a healthy level of activity. Falling demand and increased over-capacity in some regions - the immediate consequences of the deteriorating economic conditions over the past two years - have led to declining margins and to financial accounts being in the red. The adoption of increasingly stringent emissions standards and product specifications, burdensome regulatory requirements for refineries (for combating local pollution and reducing greenhouse gas emissions), stiffer competition from new fuels: all of these structural factors are weakening the sector, especially in industrialized nations with their more rigorous regulatory compliance. In this generally gloomy climate, numerous new projects are still being envisaged - although many have recently been postponed and tend to be concentrated in developing countries. (author)

  5. Initial conditions for cosmological perturbations

    Science.gov (United States)

    Ashtekar, Abhay; Gupt, Brajesh

    2017-02-01

    Penrose proposed that the big bang singularity should be constrained by requiring that the Weyl curvature vanishes there. The idea behind this past hypothesis is attractive because it constrains the initial conditions for the universe in geometric terms and is not confined to a specific early universe paradigm. However, the precise statement of Penrose’s hypothesis is tied to classical space-times and furthermore restricts only the gravitational degrees of freedom. These are encapsulated only in the tensor modes of the commonly used cosmological perturbation theory. Drawing inspiration from the underlying idea, we propose a quantum generalization of Penrose’s hypothesis using the Planck regime in place of the big bang, and simultaneously incorporating tensor as well as scalar modes. Initial conditions selected by this generalization constrain the universe to be as homogeneous and isotropic in the Planck regime as permitted by the Heisenberg uncertainty relations.

  6. Initial conditions for cosmological perturbations

    International Nuclear Information System (INIS)

    Ashtekar, Abhay; Gupt, Brajesh

    2017-01-01

    Penrose proposed that the big bang singularity should be constrained by requiring that the Weyl curvature vanishes there. The idea behind this past hypothesis is attractive because it constrains the initial conditions for the universe in geometric terms and is not confined to a specific early universe paradigm. However, the precise statement of Penrose’s hypothesis is tied to classical space-times and furthermore restricts only the gravitational degrees of freedom. These are encapsulated only in the tensor modes of the commonly used cosmological perturbation theory. Drawing inspiration from the underlying idea, we propose a quantum generalization of Penrose’s hypothesis using the Planck regime in place of the big bang, and simultaneously incorporating tensor as well as scalar modes. Initial conditions selected by this generalization constrain the universe to be as homogeneous and isotropic in the Planck regime as permitted by the Heisenberg uncertainty relations . (paper)

  7. Bioventing of gasoline-contaminated soil under varied laboratory conditions

    International Nuclear Information System (INIS)

    Hallman, M.; Shewfelt, K.; Lee, H.; Zytner, R.G.

    2002-01-01

    Bioventing is becoming a popular in situ soil remediation technology for the treatment of hydrocarbon-contaminated soil. Bioventing relies on enhancing the growth of indigenous microorganisms, which can mineralize the contaminant in the presence of sufficient nutrients. Although bioventing is currently being used as a remediation technology, there are some important questions that remain to be answered in order to optimize the process. These questions include the optimum soil moisture content, type and amount of nutrients necessary, and the best means of producing these conditions in the field. To address these questions, two distinct phases of experiments were conducted. The first experimental phase was designed to determine the optimum moisture content, C:N ratio and form of nitrogen supply for this soil. Using approximately 200g of contaminated soil in each of a series of sealed respirometers, microbial degradation of gasoline under bioventing conditions was quantified for C:N ratios of 5, 10 and 20:1, using varying mixtures of NH 4 + - and NO 3 - -N. The results of the studies indicated that the optimum soil moisture content was 15 wt%, with a C:N ratio of 10:1, using a 100% ammonium application. Using the results of the first phase, a second phase of laboratory research was initiated. Five mesoscale reactors have been developed to simulate the bioventing process that takes place in the field. These reactors are filled with approximately 4kg of gasoline-contaminated soil. The initial results are favourable. (author)

  8. Contact Dynamics of EHL Contacts under Time Varying Conditions

    NARCIS (Netherlands)

    Venner, Cornelis H.; Popovici, G.; Wijnant, Ysbrand H.; Dalmaz, G.; Lubrecht, A.A.; Priest, M

    2004-01-01

    By means of numerical simulations of two situations with time varying operating conditions it is shown that the dynamic behaviour of Elasto-Hydrodynamically Lubricated contacts in terms of vibrations can be characterized as: Changes in the mutual approach lead to film thickness changes in the inlet

  9. Robustness of inflation to inhomogeneous initial conditions

    Energy Technology Data Exchange (ETDEWEB)

    Clough, Katy; Lim, Eugene A. [Theoretical Particle Physics and Cosmology Group, Physics Department, Kings College London, Strand, London WC2R 2LS (United Kingdom); DiNunno, Brandon S.; Fischler, Willy; Flauger, Raphael; Paban, Sonia, E-mail: katy.clough@kcl.ac.uk, E-mail: eugene.a.lim@gmail.com, E-mail: bsd86@physics.utexas.edu, E-mail: fischler@physics.utexas.edu, E-mail: flauger@physics.utexas.edu, E-mail: paban@physics.utexas.edu [Department of Physics, The University of Texas at Austin, Austin, TX, 78712 (United States)

    2017-09-01

    We consider the effects of inhomogeneous initial conditions in both the scalar field profile and the extrinsic curvature on different inflationary models. In particular, we compare the robustness of small field inflation to that of large field inflation, using numerical simulations with Einstein gravity in 3+1 dimensions. We find that small field inflation can fail in the presence of subdominant gradient energies, suggesting that it is much less robust to inhomogeneities than large field inflation, which withstands dominant gradient energies. However, we also show that small field inflation can be successful even if some regions of spacetime start out in the region of the potential that does not support inflation. In the large field case, we confirm previous results that inflation is robust if the inflaton occupies the inflationary part of the potential. Furthermore, we show that increasing initial scalar gradients will not form sufficiently massive inflation-ending black holes if the initial hypersurface is approximately flat. Finally, we consider the large field case with a varying extrinsic curvature K , such that some regions are initially collapsing. We find that this may again lead to local black holes, but overall the spacetime remains inflationary if the spacetime is open, which confirms previous theoretical studies.

  10. Vibration condition monitoring of planetary gearbox under varying external load

    Energy Technology Data Exchange (ETDEWEB)

    Bartelmus, W.; Zimroz, R. [Wroclaw University of Technology, Wroclaw (Poland)

    2009-01-15

    The paper shows that for condition monitoring of planetary gearboxes it is important to identify the external varying load condition. In the paper, systematic consideration has been taken of the influence of many factors on the vibration signals generated by a system in which a planetary gearbox is included. These considerations give the basis for vibration signal interpretation, development of the means of condition monitoring, and for the scenario of the degradation of the planetary gearbox. Real measured vibration signals obtained in the industrial environment are processed. The signals are recorded during normal operation of the diagnosed objects, namely planetary gearboxes, which are a part of the driving system used in a bucket wheel excavator, used in lignite mines. It has been found that the most important factor of the proper planetary gearbox condition is connected with perturbation of arm rotation, where an arm rotation gives rise to a specific vibration signal whose properties are depicted by a short-time Fourier transform (STFT) and Wigner-Ville distribution presented as a time-frequency map. The paper gives evidence that there are two dominant low-frequency causes that influence vibration signal modulation, i.e. the varying load, which comes from the nature of the bucket wheel digging process, and the arm/carrier rotation. These two causes determine the condition of the planetary gearboxes considered.

  11. Conditional CAPM: Time-varying Betas in the Brazilian Market

    Directory of Open Access Journals (Sweden)

    Frances Fischberg Blank

    2014-10-01

    Full Text Available The conditional CAPM is characterized by time-varying market beta. Based on state-space models approach, beta behavior can be modeled as a stochastic process dependent on conditioning variables related to business cycle and estimated using Kalman filter. This paper studies alternative models for portfolios sorted by size and book-to-market ratio in the Brazilian stock market and compares their adjustment to data. Asset pricing tests based on time-series and cross-sectional approaches are also implemented. A random walk process combined with conditioning variables is the preferred model, reducing pricing errors compared to unconditional CAPM, but the errors are still significant. Cross-sectional test show that book-to-market ratio becomes less relevant, but past returns still capture cross-section variation

  12. Atmospheric particle formation in spatially and temporally varying conditions

    Energy Technology Data Exchange (ETDEWEB)

    Lauros, J.

    2011-07-01

    Atmospheric particles affect the radiation balance of the Earth and thus the climate. New particle formation from nucleation has been observed in diverse atmospheric conditions but the actual formation path is still unknown. The prevailing conditions can be exploited to evaluate proposed formation mechanisms. This study aims to improve our understanding of new particle formation from the view of atmospheric conditions. The role of atmospheric conditions on particle formation was studied by atmospheric measurements, theoretical model simulations and simulations based on observations. Two separate column models were further developed for aerosol and chemical simulations. Model simulations allowed us to expand the study from local conditions to varying conditions in the atmospheric boundary layer, while the long-term measurements described especially characteristic mean conditions associated with new particle formation. The observations show statistically significant difference in meteorological and back-ground aerosol conditions between observed event and non-event days. New particle formation above boreal forest is associated with strong convective activity, low humidity and low condensation sink. The probability of a particle formation event is predicted by an equation formulated for upper boundary layer conditions. The model simulations call into question if kinetic sulphuric acid induced nucleation is the primary particle formation mechanism in the presence of organic vapours. Simultaneously the simulations show that ignoring spatial and temporal variation in new particle formation studies may lead to faulty conclusions. On the other hand, the theoretical simulations indicate that short-scale variations in temperature and humidity unlikely have a significant effect on mean binary water sulphuric acid nucleation rate. The study emphasizes the significance of mixing and fluxes in particle formation studies, especially in the atmospheric boundary layer. The further

  13. One-dimensional radionuclide transport under time-varying conditions

    International Nuclear Information System (INIS)

    Gelbard, F.; Olague, N.E.; Longsine, D.E.

    1990-01-01

    This paper discusses new analytical and numerical solutions presented for one-dimensional radionuclide transport under time-varying fluid-flow conditions including radioactive decay. The analytical solution assumes that all radionuclides have identical retardation factors, and is limited to instantaneous releases. The numerical solution does not have these limitations, but is tested against the limiting case given for the analytical solution. Reasonable agreement between the two solutions was found. Examples are given for the transport of a three-member radionuclide chain transported over distances and flow rates comparable to those reported for Yucca Mountain, the proposed disposal site for high-level nuclear waste

  14. A thermal model for photovoltaic panels under varying atmospheric conditions

    International Nuclear Information System (INIS)

    Armstrong, S.; Hurley, W.G.

    2010-01-01

    The response of the photovoltaic (PV) panel temperature is dynamic with respect to the changes in the incoming solar radiation. During periods of rapidly changing conditions, a steady state model of the operating temperature cannot be justified because the response time of the PV panel temperature becomes significant due to its large thermal mass. Therefore, it is of interest to determine the thermal response time of the PV panel. Previous attempts to determine the thermal response time have used indoor measurements, controlling the wind flow over the surface of the panel with fans or conducting the experiments in darkness to avoid radiative heat loss effects. In real operating conditions, the effective PV panel temperature is subjected to randomly varying ambient temperature and fluctuating wind speeds and directions; parameters that are not replicated in controlled, indoor experiments. A new thermal model is proposed that incorporates atmospheric conditions; effects of PV panel material composition and mounting structure. Experimental results are presented which verify the thermal behaviour of a photovoltaic panel for low to strong winds.

  15. Estimation of thermal sensation during varied air temperature conditions.

    Science.gov (United States)

    Katsuura, T; Tabuchi, R; Iwanaga, K; Harada, H; Kikuchi, Y

    1998-03-01

    Seven male students were exposed to four varied air temperature environments: hot (37 degrees C) to neutral (27 degrees C) (HN), neutral to hot (NH), cool (17 degrees C) to neutral (CN), and neutral to cool (NC). The air temperature was maintained at the first condition for 20 min, then was changed to the second condition after 15 min and was held there for 20 min. Each subject wore a T-shirt, briefs, trunks, and socks. Each sat on a chair and was continuously evaluated for thermal sensation, thermal comfort, and air velocity sensation. Some physiological and thermal parameters were also measured every 5 s during the experiment. The correlation between thermal sensation and skin temperature at 15 sites was found to be poor. The subjects felt much warmer during the rising phase of the air temperature (CN, NH) than during the descending phase (HN, NC) at a given mean skin temperature. However, thermal sensation at the same heat flux or at the same value of the difference between skin and air temperature (delta(Tsk - Ta)) was not so different among the four experimental conditions, and the correlation between thermal sensation and heat flux or delta(Tsk - Ta) was fairly good. The multiple regression equation of the thermal sensation (TS) on 15 sites of skin temperature (Tsk; degrees C) was calculated and the coefficient of determination (R*2) was found to be 0.656. Higher coefficients of determination were found in the equations of thermal sensation for the heat flux (H; kcal.m-2.h-1) at the right and left thighs of the subjects and on delta(Tsk - Ta) (degrees C) at 4 sites. They were as follows: TS = 2.04 - 0.016 Hright - 0.036 Hleft; R*2 = 0.717, TS = 1.649 + 0.013 delta(Tsk - Ta)UpperArm - 0.036 delta(Tsk - Ta)Chest - 0.223 delta(Tsk - Ta)Thigh-0.083 delta(Tsk - Ta)LowerLeg; R*2 = 0.752, respectively.

  16. Cosmological constant and general isocurvature initial conditions

    International Nuclear Information System (INIS)

    Trotta, R.; Riazuelo, A.; Durrer, R.

    2003-01-01

    We investigate in detail the question of whether a nonvanishing cosmological constant is required by the present-day cosmic microwave background and large scale structure data when general isocurvature initial conditions are taken into account. We also discuss the differences between the usual Bayesian and the frequentist approaches in data analysis. We show that the Cosmic Background Explorer (COBE)-normalized matter power spectrum is dominated by the adiabatic mode and therefore breaks the degeneracy between initial conditions which is present in the cosmic microwave background anisotropies. We find that in a flat universe the Bayesian analysis requires Ω Λ =e0 to more than 3σ, while in the frequentist approach Ω Λ =0 is still within 3σ for a value of h≤0.48. Both conclusions hold regardless of the initial conditions

  17. Thermal shock behaviour of different tungsten grades under varying conditions

    Energy Technology Data Exchange (ETDEWEB)

    Wirtz, Oliver Marius

    2012-07-19

    Thermonuclear fusion power plants are a promising option to ensure the energy supply for future generations, but in many fields of research enormous challenges have to be faced. A major step on the way to the prototype fusion reactor DEMO will be ITER which is build in Cadarache, southern France. One of the most critical issues is the field of in-vessel materials and components, in particular the plasma facing materials (PFM). PFMs that will be used in a device like ITER have to withstand severe environmental conditions in terms of steady state and transient thermal loads as well as high particle fluxes such as hydrogen, helium and neutrons. Candidate wall materials are beryllium, tungsten and carbon based materials like CFC (carbon fibre composite). Tungsten is the most promising material for an application in the divertor region with very severe loading conditions and it will most probably also be used as PFM for DEMO. Hence, this work focuses on the investigation of the thermal shock response of different tungsten grades in order to understand the damage mechanisms and to identify material parameters which influence this behaviour under ITER and DEMO relevant operation conditions. Therefore the microstructure and the mechanical and thermal properties of five industrially manufactured tungsten grades were characterised. All five tungsten grades were exposed to transient thermal events with very high power densities of up to 1.27 GWm{sup -2} at varying base temperatures between RT and 600 C in the electron beam device JUDITH 1. The pulse numbers were limited to a maximum of 1000 in order to avoid immoderate workload on the test facility and to have enough time to cover a wide range of loading conditions. The results of this damage mapping enable to define different damage and cracking thresholds for the investigated tungsten grades and to identify certain material parameters which influence the location of these thresholds and the distinction of the induced

  18. Thermal shock behaviour of different tungsten grades under varying conditions

    International Nuclear Information System (INIS)

    Wirtz, Oliver Marius

    2012-01-01

    Thermonuclear fusion power plants are a promising option to ensure the energy supply for future generations, but in many fields of research enormous challenges have to be faced. A major step on the way to the prototype fusion reactor DEMO will be ITER which is build in Cadarache, southern France. One of the most critical issues is the field of in-vessel materials and components, in particular the plasma facing materials (PFM). PFMs that will be used in a device like ITER have to withstand severe environmental conditions in terms of steady state and transient thermal loads as well as high particle fluxes such as hydrogen, helium and neutrons. Candidate wall materials are beryllium, tungsten and carbon based materials like CFC (carbon fibre composite). Tungsten is the most promising material for an application in the divertor region with very severe loading conditions and it will most probably also be used as PFM for DEMO. Hence, this work focuses on the investigation of the thermal shock response of different tungsten grades in order to understand the damage mechanisms and to identify material parameters which influence this behaviour under ITER and DEMO relevant operation conditions. Therefore the microstructure and the mechanical and thermal properties of five industrially manufactured tungsten grades were characterised. All five tungsten grades were exposed to transient thermal events with very high power densities of up to 1.27 GWm -2 at varying base temperatures between RT and 600 C in the electron beam device JUDITH 1. The pulse numbers were limited to a maximum of 1000 in order to avoid immoderate workload on the test facility and to have enough time to cover a wide range of loading conditions. The results of this damage mapping enable to define different damage and cracking thresholds for the investigated tungsten grades and to identify certain material parameters which influence the location of these thresholds and the distinction of the induced damages

  19. Initial conditions for critical Higgs inflation

    Science.gov (United States)

    Salvio, Alberto

    2018-05-01

    It has been pointed out that a large non-minimal coupling ξ between the Higgs and the Ricci scalar can source higher derivative operators, which may change the predictions of Higgs inflation. A variant, called critical Higgs inflation, employs the near-criticality of the top mass to introduce an inflection point in the potential and lower drastically the value of ξ. We here study whether critical Higgs inflation can occur even if the pre-inflationary initial conditions do not satisfy the slow-roll behavior (retaining translation and rotation symmetries). A positive answer is found: inflation turns out to be an attractor and therefore no fine-tuning of the initial conditions is necessary. A very large initial Higgs time-derivative (as compared to the potential energy density) is compensated by a moderate increase in the initial field value. These conclusions are reached by solving the exact Higgs equation without using the slow-roll approximation. This also allows us to consistently treat the inflection point, where the standard slow-roll approximation breaks down. Here we make use of an approach that is independent of the UV completion of gravity, by taking initial conditions that always involve sub-planckian energies.

  20. Initial conditions for turbulent mixing simulations

    Directory of Open Access Journals (Sweden)

    T. Kaman

    2010-01-01

    Full Text Available In the context of the classical Rayleigh-Taylor hydrodynamical instability, we examine the much debated question of models for initial conditions and the possible influence of unrecorded long wave length contributions to the instability growth rate α.

  1. Initial conditioning of the TFTR vacuum vessel

    International Nuclear Information System (INIS)

    Dylla, H.F.; Blanchard, W.R.; Krawchuk, R.B.; Hawryluk, R.J.; Owens, D.K.

    1984-01-01

    We report on the initial conditioning of the Tokamak Fusion Test Reactor (TFTR) vacuum vessel prior to the initiation of first plasma discharges, and during subsequent operation with high power ohmically-heated plasmas. Following evacuation of the 86 m 3 vessel with the 10 4 1/s high vacuum pumping system, the vessel was conditioned by a 15 A dc glow discharge in H 2 at a pressure of 5 mTorr. Rapid-pulse discharge cleaning was used subsequently to preferentially condition the graphite plasma limiters. The effectiveness of the discharge cleaning was monitored by measuring the exhaust rates of the primary discharge products (CO/C 2 H 4 , CH 4 , and H 2 O). After 175 hours of glow discharge treatment, the equivalent of 50 monolayers of C and O was removed from the vessel, and the partial pressures of impurity gases were reduced to the range of 10 -9 -10 -10 Torr

  2. Initial conditions and entanglement sudden death

    International Nuclear Information System (INIS)

    Qian, Xiao-Feng; Eberly, J.H.

    2012-01-01

    We report results bearing on the behavior of non-local decoherence and its potential for being managed or even controlled. The decoherence process known as entanglement sudden death (ESD) can drive prepared entanglement to zero at the same time that local coherences and fidelity remain non-zero. For a generic ESD-susceptible Bell superposition state, we provide rules restricting the occurrence and timing of ESD, amounting to management tools over a continuous variation of initial conditions. These depend on only three parameters: initial purity, entanglement and excitation. Knowledge or control of initial phases is not needed. -- Highlights: ► We study the possibility of managing disentanglement through initial conditions. ► The initial parameters are the amount of entanglement, excitation, and purity. ► Entanglement sudden death (ESD) free and ESD susceptible phases are identified. ► ESD onset time is also presented in the ESD susceptible phase. ► Our results may guide experiments to prepare ESD free or delayed ESD states.

  3. Crack initiation under generalized plane strain conditions

    International Nuclear Information System (INIS)

    Shum, D.K.M.; Merkle, J.G.

    1991-01-01

    A method for estimating the decrease in crack-initiation toughness, from a reference plane strain value, due to positive straining along the crack front of a circumferential flaw in a reactor pressure vessel is presented in this study. This method relates crack initiation under generalized plane strain conditions with material failure at points within a distance of a few crack-tip-opening displacements ahead of a crack front, and involves the formulation of a micromechanical crack-initiation model. While this study is intended to address concerns regarding the effects of positive out-of- plane straining on ductile crack initiation, the approach adopted in this work can be extended in a straightforward fashion to examine conditions of macroscopic cleavage crack initiation. Provided single- parameter dominance of near-tip fields exists in the flawed structure, results from this study could be used to examine the appropriateness of applying plane strain fracture toughness to the evaluation of circumferential flaws, in particular to those in ring-forged vessels which have no longitudinal welds. In addition, results from this study could also be applied toward the analysis of the effects of thermal streaming on the fracture resistance of circumferentially oriented flaws in a pressure vessel. 37 refs., 8 figs., 1 tab

  4. On the initial condition of inflationary fluctuations

    International Nuclear Information System (INIS)

    Jiang, Hongliang; Wang, Yi; Zhou, Siyi

    2016-01-01

    It is usually assumed that the inflationary fluctuations start from the Bunch-Davies (BD) vacuum and the iε prescription is used when interactions are calculated. We show that those assumptions can be verified explicitly by calculating the loop corrections to the inflationary two-point and three-point correlation functions. Those loop corrections can be resummed to exponential factors, which suppress non-BD coefficients and behave as the iε factor for the case of the BD initial condition. A new technique of loop chain diagram resummation is developed for this purpose. For the non-BD initial conditions which is setup at finite time and has not fully decayed, explicit correction to the two-point and three-point correlation functions are calculated. Especially, non-Gaussianity in the folded limit is regularized due to the interactions.

  5. Initial phase wall conditioning in KSTAR

    International Nuclear Information System (INIS)

    Hong, Suk-Ho; Kim, Kwang-Pyo; Kim, Sungwoo; Lee, Dong-Su; Kim, Kyung-Min; Lee, Kun-Su; Kim, Jong-Su; Park, Jae-Min; Kim, Woong-Chae; Kim, Hak-Kun; Park, Kap-Rai; Yang, Hyung-Lyeol; Sun, Jong-Ho; Woo, Hyun-Jong; Lee, Sang-Yong; Lee, Sang-Hwa; Park, Eun-Kyung; Park, Sang-Joon; Kim, Sun-Ho; Wang, Sun-Jung

    2011-01-01

    The initial phase wall conditioning in KSTAR is depicted. The KSTAR wall conditioning procedure consists of vessel baking, glow discharge cleaning (GDC), ICRH wall conditioning (ICWC) and boronization (Bz). Vessel baking is performed for the initial vacuum conditioning in order to remove various kinds of impurities including H 2 O, carbon and oxygen and for the plasma operation. The total outgassing rates after vessel baking in three successive KSTAR campaigns are compared. GDC is regularly performed as a standard wall cleaning procedure. Another cleaning technique is ICWC, which is useful for inter-shot wall conditioning under a strong magnetic field. In order to optimize the operation time and removal efficiency of ICWC, a parameter scan is performed. Bz is a standard technique to remove oxygen impurity from a vacuum vessel. KSTAR has used carborane powder which is a non-toxic boron-containing material. The KSTAR Bz has been successfully performed through two campaigns: water and oxygen levels in the vacuum vessel are reduced significantly. As a result, KSTAR has achieved its first L-H mode transition, although the input power was marginal for the L-H transition threshold. The characteristics of boron-containing thin films deposited for boronization are investigated.

  6. Tubular Initial Conditions and Ridge Formation

    Directory of Open Access Journals (Sweden)

    M. S. Borysova

    2013-01-01

    Full Text Available The 2D azimuth and rapidity structure of the two-particle correlations in relativistic A+A collisions is altered significantly by the presence of sharp inhomogeneities in superdense matter formed in such processes. The causality constraints enforce one to associate the long-range longitudinal correlations observed in a narrow angular interval, the so-called (soft ridge, with peculiarities of the initial conditions of collision process. This study's objective is to analyze whether multiform initial tubular structures, undergoing the subsequent hydrodynamic evolution and gradual decoupling, can form the soft ridges. Motivated by the flux-tube scenarios, the initial energy density distribution contains the different numbers of high density tube-like boost-invariant inclusions that form a bumpy structure in the transverse plane. The influence of various structures of such initial conditions in the most central A+A events on the collective evolution of matter, resulting spectra, angular particle correlations and vn-coefficients is studied in the framework of the hydrokinetic model (HKM.

  7. The Initial Conditions of Fractional Calculus

    International Nuclear Information System (INIS)

    Trigeassou, J. C.; Maamri, N.

    2011-01-01

    During the past fifty years , Fractional Calculus has become an original and renowned mathematical tool for the modelling of diffusion Partial Differential Equations and the design of robust control algorithms. However, in spite of these celebrated results, some theoretical problems have not yet received a satisfying solution. The mastery of initial conditions, either for Fractional Differential Equations (FDEs) or for the Caputo and Riemann-Liouville fractional derivatives, remains an open research domain. The solution of this fundamental problem, also related to the long range memory property, is certainly the necessary prerequisite for a satisfying approach to modelling and control applications. The fractional integrator and its continuously frequency distributed differential model is a valuable tool for the simulation of fractional systems and the solution of initial condition problems. Indeed, the infinite dimensional state vector of fractional integrators allows the direct generalization to fractional calculus of the theoretical results of integer order systems. After a reminder of definitions and properties related to fractional derivatives and systems, this presentation is intended to show, based on the results of two recent publications [1,2], how the fractional integrator provides the solution of the initial condition problem of FDEs and of Caputo and Riemann-Liouville fractional derivatives. Numerical simulation examples illustrate and validate these new theoretical concepts.

  8. Design of Multijunction Photovoltaic Cells Optimized for Varied Atmospheric Conditions

    Directory of Open Access Journals (Sweden)

    C. Zhang

    2014-01-01

    Full Text Available Band gap engineering provides an opportunity to not only provide higher overall conversion efficiencies of the reference AM1.5 spectra but also customize PV device design for specific geographic locations and microenvironments based on atmospheric conditions characteristic to that particular location. Indium gallium nitride and other PV materials offer the opportunity for limited bandgap engineering to match spectra. The effects of atmospheric conditions such as aerosols, cloud cover, water vapor, and air mass have been shown to cause variations in spectral radiance that alters PV system performance due to both overrating and underrating. Designing PV devices optimized for spectral radiance of a particular region can result in improved PV system performance. This paper presents a new method for designing geographically optimized PV cells with using a numerical model for bandgap optimization. The geographic microclimate spectrally resolved solar flux for twelve representative atmospheric conditions for the incident radiation angle (zenith angle of 48.1° and fixed array angle of 40° is used to iteratively optimize the band gap for tandem, triple, and quad-layer of InGaN-based multijunction cells. The results of this method are illustrated for the case study of solar farms in the New York region and discussed.

  9. Varied overstrain injuries of the vertebral column conditioned by evolution

    Energy Technology Data Exchange (ETDEWEB)

    Kohlbach, W

    1983-08-01

    During physiological growth of the juvenile vertebral column, various stages of stability occur which are characterized by the condition of the marginal rim of the vertebral bodies. If the vertebral juvenile column is overstrained, these variations in stability results in a variety of damage to vertebral bodies and vertebral disks. One of these lesions corresponds to Scheuermann's disease (osteochondrosis of vertebral epiphyses in juveniles). Damage of the vertebral column due to overstrain can occur only if the overstrain is applied in upright position. Since Man alone can damage his vertebral column in upright position (as a result of his evolutionary development), Scheuermann's thesis is confirmed that Scheuermann's disease is confined to Man. Spondylolysis/spondylolisthesis is also a damage caused by overstrain. Here, too, the damage can occur only if the load is exercised in upright position, with the exception of a slanted positioning of the intervertebral components.

  10. Varied overstrain injuries of the vertebral column conditioned by evolution

    International Nuclear Information System (INIS)

    Kohlbach, W.

    1983-01-01

    During physiological growth of the juvenile vertebral column, various stages of stability occur which are characterized by the condition of the marginal rim of the vertebral bodies. If the vertebral juvenile column is overstrained, these variations in stability results in a variety of damage to vertebral bodies and vertebral disks. One of these lesions corresponds to Scheuermann's disease (osteochondrosis of vertebral epiphyses in juveniles). Damage of the vertebral column due to overstrain can occur only if the overstrain is applied in upright position. Since Man alone can damage his vertebral column in upright position (as a result of his evolutionary development), Scheuermann's thesis is confirmed that Scheuermann's disease is confined to Man. Spondylolysis/spondylolisthesis is also a damage caused by overstrain. Here, too, the damage can occur only if the load is exercised in upright position, with the exception of a slanted positioning of the intervertebral components. (orig.) [de

  11. Varied overstrain injuries of the vertebral column conditioned by evolution

    Energy Technology Data Exchange (ETDEWEB)

    Kohlbach, W.

    1983-08-01

    During physiological growth of the juvenile vertebral column, various stages of stability occur which are characterized by the condition of the marginal rim of the vertebral bodies. If the vertebral juvenile column is overstrained, these variations in stability results in a variety of damage to vertebral bodies and vertebral disks. One of these lesions corresponds to Scheuermann's disease (osteochondrosis of vertebral epiphyses in juveniles). Damage of the vertebral column due to overstrain can occur only if the overstrain is applied in upright position. Since Man alone can damage his vertebral column in upright position (as a result of his evolutionary development), Scheuermann's thesis is confirmed that Scheuermann's disease is confined to Man. Spondylolysis/spondylolisthesis is also a damage caused by overstrain. Here, too, the damage can occur only if the load is exercised in upright position, with the exception of a slanted positioning of the intervertebral components.

  12. Initial conditions of radiative shock experiments

    International Nuclear Information System (INIS)

    Kuranz, C. C.; Drake, R. P.; Krauland, C. M.; Marion, D. C.; Grosskopf, M. J.; Rutter, E.; Torralva, B.; Holloway, J. P.; Bingham, D.; Goh, J.; Boehly, T. R.; Sorce, A. T.

    2013-01-01

    We performed experiments at the Omega Laser Facility to characterize the initial, laser-driven state of a radiative shock experiment. These experiments aimed to measure the shock breakout time from a thin, laser-irradiated Be disk. The data are then used to inform a range of valid model parameters, such as electron flux limiter and polytropic γ, used when simulating radiative shock experiments using radiation hydrodynamics codes. The characterization experiment and the radiative shock experiment use a laser irradiance of ∼7 × 10 14 W cm −2 to launch a shock in the Be disk. A velocity interferometer and a streaked optical pyrometer were used to infer the amount of time for the shock to move through the Be disk. The experimental results were compared with simulation results from the Hyades code, which can be used to model the initial conditions of a radiative shock system using the CRASH code

  13. Weed spectrum and selectivity of tembotrione under varying environmental conditions

    Directory of Open Access Journals (Sweden)

    Gatzweiler, Elmar

    2012-03-01

    Full Text Available Tembotrione is a novel HPPD maize herbicide effective against a wide range of broadleaf and grass weeds. Some characteristics of this compound are described in this paper linking weed and crop responses following tembotrione applications to environmental parameters or use conditions. The activity of HPPD herbicides is very much dependant on the availability of light. Increasing illumination intensities following application augmented the activity levels of several comparable HPPD compounds in a growth chamber experiment. Tembotrione was shown to be more efficacious at low and high illumination intensities compared to standard herbicides applied at the same rate. At the high intensity, tembotrione retained its high efficacy from two up to four weeks after application showing a rapid and strong herbicidal activity. The activity following post-emergent treatments of tembotrione against broadleaf weeds was influenced by soil characteristics such as soil texture and organic matter content in a glasshouse test. The level of weed suppression clearly declined stronger on heavier soils than on lighter soils at a rather low application rate of 12.5 g a.i./ha and lower. This is a clear indication of residual efficacy of tembotrione. The selectivity of tembotrione was tested on numerous maize varieties following post-emergent treatment with tembotrione alone or in mixture with the safener isoxadifen-ethyl under field conditions in Germany in comparison to a standard herbicide. The level of crop phytotoxicity tended to increase in the following order: Tembotrione plus safener, standard herbicide to tembotrione alone. Only the mixture of tembotrione with safener did not cause significant adverse effects on maize. Another field experiment in the USA examined crop phytotoxicity using one maize variety in a situation of infurrow soil insecticide treatment followed by a post-emergent application of tembotrione (plus/minus isoxadifen-ethyl and standard herbicides

  14. Effect of Initial Conditions on Reproducibility of Scientific Research

    Science.gov (United States)

    Djulbegovic, Benjamin; Hozo, Iztok

    2014-01-01

    Background: It is estimated that about half of currently published research cannot be reproduced. Many reasons have been offered as explanations for failure to reproduce scientific research findings- from fraud to the issues related to design, conduct, analysis, or publishing scientific research. We also postulate a sensitive dependency on initial conditions by which small changes can result in the large differences in the research findings when attempted to be reproduced at later times. Methods: We employed a simple logistic regression equation to model the effect of covariates on the initial study findings. We then fed the input from the logistic equation into a logistic map function to model stability of the results in repeated experiments over time. We illustrate the approach by modeling effects of different factors on the choice of correct treatment. Results: We found that reproducibility of the study findings depended both on the initial values of all independent variables and the rate of change in the baseline conditions, the latter being more important. When the changes in the baseline conditions vary by about 3.5 to about 4 in between experiments, no research findings could be reproduced. However, when the rate of change between the experiments is ≤2.5 the results become highly predictable between the experiments. Conclusions: Many results cannot be reproduced because of the changes in the initial conditions between the experiments. Better control of the baseline conditions in-between the experiments may help improve reproducibility of scientific findings. PMID:25132705

  15. MUSIC: MUlti-Scale Initial Conditions

    Science.gov (United States)

    Hahn, Oliver; Abel, Tom

    2013-11-01

    MUSIC generates multi-scale initial conditions with multiple levels of refinements for cosmological ‘zoom-in’ simulations. The code uses an adaptive convolution of Gaussian white noise with a real-space transfer function kernel together with an adaptive multi-grid Poisson solver to generate displacements and velocities following first- (1LPT) or second-order Lagrangian perturbation theory (2LPT). MUSIC achieves rms relative errors of the order of 10-4 for displacements and velocities in the refinement region and thus improves in terms of errors by about two orders of magnitude over previous approaches. In addition, errors are localized at coarse-fine boundaries and do not suffer from Fourier space-induced interference ringing.

  16. Chaotic digital communication by encoding initial conditions.

    Science.gov (United States)

    Xiaofeng, Gong; Xingang, Wang; Meng, Zhan; Lai, C H

    2004-06-01

    We investigate the possibility to improve the noise performance of a chaotic digital communication scheme by utilizing further dynamical information. We show that by encoding the initial information of the chaotic carrier according to the transmitting bits, extra redundance can be introduced into the segments of chaotic signals corresponding to the consecutive bits. Such redundant information can be exploited effectively at the receiver end to improve the noise performance of the system. Compared to other methods (e.g., differential chaos shift keying), straightforward application of the proposed modulation/demodulation scheme already provides significant performance gain in the low signal-to-noise ratio (SNR) region. Furthermore, maximum likelihood precleaning procedure based on the Viterbi algorithm can be applied before the demodulation step to overcome the performance degradation in the high SNR region. The study indicates that it is possible to improve the noise performance of the chaotic digital communication scheme if further dynamics information is added to the system. (c) 2004 American Institute of Physics

  17. Modelling and Control of Ionic Electroactive Polymer Actuators under Varying Humidity Conditions

    Directory of Open Access Journals (Sweden)

    S. Sunjai Nakshatharan

    2018-02-01

    Full Text Available In this work, we address the problem of position control of ionic electroactive polymer soft actuators under varying relative humidity conditions. The impact of humidity on the actuation performance of ionic actuators is studied through frequency response and impedance spectroscopy analysis. Considering the uncertain performance of the actuator under varying humidity conditions, an adaptable model using the neural network method is developed. The model uses relative humidity magnitude as one of the model parameters, making it robust to different environmental conditions. Utilizing the model, a closed-loop controller based on the model predictive controller is developed for position control of the actuator. The developed model and controller are experimentally verified and found to be capable of predicting and controlling the actuators with excellent tracking accuracy under relative humidity conditions varying in the range of 10–90%.

  18. The Dependence of Chimera States on Initial Conditions

    International Nuclear Information System (INIS)

    Feng Yue-E; Li Hai-Hong

    2015-01-01

    A chimera state consisting of both coherent and incoherent groups is a fascinating spatial pattern in non-locally coupled identical oscillators. It is thought that random initial conditions hardly evolve to chimera states. In this work, we study the dependence of chimera states on initial conditions. We show that random initial conditions may lead to chimera states and the chance of realizing chimera states becomes increasing when the model parameters are moving away from the boundary of their stable regime. (paper)

  19. Selection of the initial conditions in the tunneling time definition

    International Nuclear Information System (INIS)

    Zajchenko, A.K.

    2004-01-01

    The necessity of changing of the initial conditions in the Olkhovsky - Recami definition of the tunneling time is justified. The new initial conditions are proposed which adequately taking into account the irreversibility of the wave packets spreading. The expression for the tunneling time with the new initial conditions is reduced to the form which is convenient for the performing and controlling the accuracy of calculations

  20. Computing Conditional VaR using Time-varying CopulasComputing Conditional VaR using Time-varying Copulas

    Directory of Open Access Journals (Sweden)

    Beatriz Vaz de Melo Mendes

    2005-12-01

    Full Text Available It is now widespread the use of Value-at-Risk (VaR as a canonical measure at risk. Most accurate VaR measures make use of some volatility model such as GARCH-type models. However, the pattern of volatility dynamic of a portfolio follows from the (univariate behavior of the risk assets, as well as from the type and strength of the associations among them. Moreover, the dependence structure among the components may change conditionally t past observations. Some papers have attempted to model this characteristic by assuming a multivariate GARCH model, or by considering the conditional correlation coefficient, or by incorporating some possibility for switches in regimes. In this paper we address this problem using time-varying copulas. Our modeling strategy allows for the margins to follow some FIGARCH type model while the copula dependence structure changes over time.

  1. Hydrometeorological threshold conditions for debris flow initiation in Norway

    Directory of Open Access Journals (Sweden)

    N. K. Meyer

    2012-10-01

    Full Text Available Debris flows, triggered by extreme precipitation events and rapid snow melt, cause considerable damage to the Norwegian infrastructure every year. To define intensity-duration (ID thresholds for debris flow initiation critical water supply conditions arising from intensive rainfall or snow melt were assessed on the basis of daily hydro-meteorological information for 502 documented debris flow events. Two threshold types were computed: one based on absolute ID relationships and one using ID relationships normalized by the local precipitation day normal (PDN. For each threshold type, minimum, medium and maximum threshold values were defined by fitting power law curves along the 10th, 50th and 90th percentiles of the data population. Depending on the duration of the event, the absolute threshold intensities needed for debris flow initiation vary between 15 and 107 mm day−1. Since the PDN changes locally, the normalized thresholds show spatial variations. Depending on location, duration and threshold level, the normalized threshold intensities vary between 6 and 250 mm day−1. The thresholds obtained were used for a frequency analysis of over-threshold events giving an estimation of the exceedance probability and thus potential for debris flow events in different parts of Norway. The absolute thresholds are most often exceeded along the west coast, while the normalized thresholds are most frequently exceeded on the west-facing slopes of the Norwegian mountain ranges. The minimum thresholds derived in this study are in the range of other thresholds obtained for regions with a climate comparable to Norway. Statistics reveal that the normalized threshold is more reliable than the absolute threshold as the former shows no spatial clustering of debris flows related to water supply events captured by the threshold.

  2. Bearing Condition Recognition and Degradation Assessment under Varying Running Conditions Using NPE and SOM

    Directory of Open Access Journals (Sweden)

    Shaohui Zhang

    2014-01-01

    Full Text Available Manifold learning methods have been widely used in machine condition monitoring and fault diagnosis. However, the results reported in these studies focus on the machine faults under stable loading and rotational speeds, which cannot interpret the practical machine running. Rotating machine is always running under variable speeds and loading, which makes the vibration signal more complicated. To address such concern, the NPE (neighborhood preserving embedding is applied for bearing fault classification. Compared with other algorithms (PCA, LPP, LDA, and ISOP, the NPE performs well in feature extraction. Since the traditional time domain signal denoising is time consuming and memory consuming, we denoise the signal features directly in feature space. Furthermore, NPE and SOM (self-organizing map are combined to assess the bearing degradation performance. Simulation and experiment results validate the effectiveness of the proposed method.

  3. Towards artificial intelligence based diesel engine performance control under varying operating conditions using support vector regression

    Directory of Open Access Journals (Sweden)

    Naradasu Kumar Ravi

    2013-01-01

    Full Text Available Diesel engine designers are constantly on the look-out for performance enhancement through efficient control of operating parameters. In this paper, the concept of an intelligent engine control system is proposed that seeks to ensure optimized performance under varying operating conditions. The concept is based on arriving at the optimum engine operating parameters to ensure the desired output in terms of efficiency. In addition, a Support Vector Machines based prediction model has been developed to predict the engine performance under varying operating conditions. Experiments were carried out at varying loads, compression ratios and amounts of exhaust gas recirculation using a variable compression ratio diesel engine for data acquisition. It was observed that the SVM model was able to predict the engine performance accurately.

  4. Leading-Edge Noise Prediction of General Airfoil Profiles with Spanwise-Varying Inflow Conditions

    NARCIS (Netherlands)

    Miotto, Renato Fuzaro; Wolf, William Roberto; De Santana, Leandro Dantas

    2018-01-01

    This paper presents a study of the leading-edge noise radiated by an airfoil undergoing a turbulent inflow. The noise prediction of generic airfoil profiles subjected to spanwise-varying inflow conditions is performed with the support of Amiet’s theory and the inverse strip technique. In the

  5. Leading-Edge Noise Prediction of General Airfoil Profiles with Spanwise-Varying Inflow Conditions

    NARCIS (Netherlands)

    Miotto, Renato Fuzaro; Wolf, William Roberto; De Santana, Leandro Dantas

    This paper presents a study of the leading-edge noise radiated by an airfoil undergoing a turbulent inflow. The noise prediction of generic airfoil profiles subjected to spanwise-varying inflow conditions is performed with the support of Amiet’s theory and the inverse strip technique. In the

  6. Incipient Fault Detection for Rolling Element Bearings under Varying Speed Conditions

    Directory of Open Access Journals (Sweden)

    Lang Xue

    2017-06-01

    Full Text Available Varying speed conditions bring a huge challenge to incipient fault detection of rolling element bearings because both the change of speed and faults could lead to the amplitude fluctuation of vibration signals. Effective detection methods need to be developed to eliminate the influence of speed variation. This paper proposes an incipient fault detection method for bearings under varying speed conditions. Firstly, relative residual (RR features are extracted, which are insensitive to the varying speed conditions and are able to reflect the degradation trend of bearings. Then, a health indicator named selected negative log-likelihood probability (SNLLP is constructed to fuse a feature set including RR features and non-dimensional features. Finally, based on the constructed SNLLP health indicator, a novel alarm trigger mechanism is designed to detect the incipient fault. The proposed method is demonstrated using vibration signals from bearing tests and industrial wind turbines. The results verify the effectiveness of the proposed method for incipient fault detection of rolling element bearings under varying speed conditions.

  7. Incipient Fault Detection for Rolling Element Bearings under Varying Speed Conditions.

    Science.gov (United States)

    Xue, Lang; Li, Naipeng; Lei, Yaguo; Li, Ningbo

    2017-06-20

    Varying speed conditions bring a huge challenge to incipient fault detection of rolling element bearings because both the change of speed and faults could lead to the amplitude fluctuation of vibration signals. Effective detection methods need to be developed to eliminate the influence of speed variation. This paper proposes an incipient fault detection method for bearings under varying speed conditions. Firstly, relative residual (RR) features are extracted, which are insensitive to the varying speed conditions and are able to reflect the degradation trend of bearings. Then, a health indicator named selected negative log-likelihood probability (SNLLP) is constructed to fuse a feature set including RR features and non-dimensional features. Finally, based on the constructed SNLLP health indicator, a novel alarm trigger mechanism is designed to detect the incipient fault. The proposed method is demonstrated using vibration signals from bearing tests and industrial wind turbines. The results verify the effectiveness of the proposed method for incipient fault detection of rolling element bearings under varying speed conditions.

  8. Effects of the initial conditions on cosmological $N$-body simulations

    OpenAIRE

    L'Huillier, Benjamin; Park, Changbom; Kim, Juhan

    2014-01-01

    Cosmology is entering an era of percent level precision due to current large observational surveys. This precision in observation is now demanding more accuracy from numerical methods and cosmological simulations. In this paper, we study the accuracy of $N$-body numerical simulations and their dependence on changes in the initial conditions and in the simulation algorithms. For this purpose, we use a series of cosmological $N$-body simulations with varying initial conditions. We test the infl...

  9. Remaining useful life estimation for deteriorating systems with time-varying operational conditions and condition-specific failure zones

    Directory of Open Access Journals (Sweden)

    Li Qi

    2016-06-01

    Full Text Available Dynamic time-varying operational conditions pose great challenge to the estimation of system remaining useful life (RUL for the deteriorating systems. This paper presents a method based on probabilistic and stochastic approaches to estimate system RUL for periodically monitored degradation processes with dynamic time-varying operational conditions and condition-specific failure zones. The method assumes that the degradation rate is influenced by specific operational condition and moreover, the transition between different operational conditions plays the most important role in affecting the degradation process. These operational conditions are assumed to evolve as a discrete-time Markov chain (DTMC. The failure thresholds are also determined by specific operational conditions and described as different failure zones. The 2008 PHM Conference Challenge Data is utilized to illustrate our method, which contains mass sensory signals related to the degradation process of a commercial turbofan engine. The RUL estimation method using the sensor measurements of a single sensor was first developed, and then multiple vital sensors were selected through a particular optimization procedure in order to increase the prediction accuracy. The effectiveness and advantages of the proposed method are presented in a comparison with existing methods for the same dataset.

  10. Globally exponential stability condition of a class of neural networks with time-varying delays

    International Nuclear Information System (INIS)

    Liao, T.-L.; Yan, J.-J.; Cheng, C.-J.; Hwang, C.-C.

    2005-01-01

    In this Letter, the globally exponential stability for a class of neural networks including Hopfield neural networks and cellular neural networks with time-varying delays is investigated. Based on the Lyapunov stability method, a novel and less conservative exponential stability condition is derived. The condition is delay-dependent and easily applied only by checking the Hamiltonian matrix with no eigenvalues on the imaginary axis instead of directly solving an algebraic Riccati equation. Furthermore, the exponential stability degree is more easily assigned than those reported in the literature. Some examples are given to demonstrate validity and excellence of the presented stability condition herein

  11. Tailoring discrete quantum walk dynamics via extended initial conditions

    Energy Technology Data Exchange (ETDEWEB)

    Valcarcel, German J de; Roldan, Eugenio [Departament d' Optica, Universitat de Valencia, Dr Moliner 50, 46100-Burjassot, Spain, EU (Spain); Romanelli, Alejandro, E-mail: german.valcarcel@uv.es, E-mail: eugenio.roldan@uv.es, E-mail: alejo@fing.edu.uy [Instituto de Fisica, Facultad de IngenierIa, Universidad de la Republica, CC 30, CP 11000, Montevideo (Uruguay)

    2010-12-15

    We study the evolution of initially extended distributions in the coined quantum walk (QW) on the line. By analysing the dispersion relation of the process, continuous wave equations are derived whose form depends on the initial distribution shape. In particular, for a class of initial conditions, the evolution is dictated by the Schroedinger equation of a free particle. As that equation also governs paraxial optical diffraction, all of the phenomenology of the latter can be implemented in the QW. This allows us, in particular, to devise an initially extended condition leading to a uniform probability distribution whose width increases linearly with time, with increasing homogeneity.

  12. Tailoring discrete quantum walk dynamics via extended initial conditions

    International Nuclear Information System (INIS)

    Valcarcel, German J de; Roldan, Eugenio; Romanelli, Alejandro

    2010-01-01

    We study the evolution of initially extended distributions in the coined quantum walk (QW) on the line. By analysing the dispersion relation of the process, continuous wave equations are derived whose form depends on the initial distribution shape. In particular, for a class of initial conditions, the evolution is dictated by the Schroedinger equation of a free particle. As that equation also governs paraxial optical diffraction, all of the phenomenology of the latter can be implemented in the QW. This allows us, in particular, to devise an initially extended condition leading to a uniform probability distribution whose width increases linearly with time, with increasing homogeneity.

  13. On the initial conditions for a universe with variable G and c

    International Nuclear Information System (INIS)

    Gomide, F.M.; Uehara, M.

    1978-01-01

    Initial conditions are discussed for a closed universe with matter injection process and with time varying G and c. It is shown that the usual interpretation for the cosmic microwave background radiation can be accepted for this model universe, provided a certain initial condition is imposed on the Pryce-Hoyle field. The time varying c is responsible for two red-shift laws one for wave-length and the other for the frequency. If radiation temperature obeys the red-shift law for frequency, the primordial Planck spectrum can be reproduced along cosmic expansion [pt

  14. ATMOSPHERIC CIRCULATION OF HOT JUPITERS: INSENSITIVITY TO INITIAL CONDITIONS

    International Nuclear Information System (INIS)

    Liu Beibei; Showman, Adam P.

    2013-01-01

    The ongoing characterization of hot Jupiters has motivated a variety of circulation models of their atmospheres. Such models must be integrated starting from an assumed initial state, which is typically taken to be a wind-free, rest state. Here, we investigate the sensitivity of hot-Jupiter atmospheric circulation to initial conditions with shallow-water models and full three-dimensional models. Those models are initialized with zonal jets, and we explore a variety of different initial jet profiles. We demonstrate that, in both classes of models, the final, equilibrated state is independent of initial condition—as long as frictional drag near the bottom of the domain and/or interaction with a specified planetary interior are included so that the atmosphere can adjust angular momentum over time relative to the interior. When such mechanisms are included, otherwise identical models initialized with vastly different initial conditions all converge to the same statistical steady state. In some cases, the models exhibit modest time variability; this variability results in random fluctuations about the statistical steady state, but we emphasize that, even in these cases, the statistical steady state itself does not depend on initial conditions. Although the outcome of hot-Jupiter circulation models depend on details of the radiative forcing and frictional drag, aspects of which remain uncertain, we conclude that the specification of initial conditions is not a source of uncertainty, at least over the parameter range explored in most current models.

  15. The Effect of Initial Irrigation Conditions on Heap Leaching Efficiency

    Science.gov (United States)

    Briseño Arellano, A. D.; Milczarek, M.; Yao, M.; Brusseau, M. L. L.

    2017-12-01

    Heap leaching is an unsaturated flow metal recovery process, in which mined ore is irrigated with a lixiviant to dissolve metal contained in the ore. The metal is then extracted from solution. Large scale operations involve stacking ore to depths of 6 to 18 meters on pads that may be hundreds of hectares in area. Heterogeneities within the stacked ore can lead to uneven wetting and the formation of preferential flow pathways, which reduces solution contact and lowers metal recovery. Furthermore, mineral dissolution can cause alteration of the porous media structure and loss of ore permeability. Many mine operators believe that slow initial irrigation rates help minimize permeability loss and increase metal recovery rates. However, this phenomenon has not been studied in detail. Experiments were conducted to investigate the effect of varying initial irrigation rates on leach ore stability. These were conducted with large columns (1.5 m high, 0.5 m in diameter) packed with crushed ore samples that are known to have permeability constraints. The columns were highly instrumented to assess potential changes in material properties both spatially and temporally. Water content was measured with three different methods: capacitance soil moisture sensors placed at 20-cm intervals; a neutron probe to periodically log every 30 cm from four different directions; and electrical resistivity sensors to create a 2-dimensional tomography profile of water content over time. Tensiometers were paired with the soil moisture sensors to measure matric suction and characterize moisture retention characteristics. A non-reactive tracer was used to characterize advective-dispersive transport under unsaturated conditions. A dye solution was introduced at the end of each experiment to map preferential pathways. Continuous monitoring of settling at the surface assisted in measuring consolidation and loss in permeability.

  16. Persistence of Initial Conditions in Continental Scale Air Quality Simulations

    Data.gov (United States)

    U.S. Environmental Protection Agency — This dataset contains the data used in Figures 1 – 6 and Table 2 of the technical note "Persistence of Initial Conditions in Continental Scale Air Quality...

  17. Sensitivity of a Simulated Derecho Event to Model Initial Conditions

    Science.gov (United States)

    Wang, Wei

    2014-05-01

    Since 2003, the MMM division at NCAR has been experimenting cloud-permitting scale weather forecasting using Weather Research and Forecasting (WRF) model. Over the years, we've tested different model physics, and tried different initial and boundary conditions. Not surprisingly, we found that the model's forecasts are more sensitive to the initial conditions than model physics. In 2012 real-time experiment, WRF-DART (Data Assimilation Research Testbed) at 15 km was employed to produce initial conditions for twice-a-day forecast at 3 km. On June 29, this forecast system captured one of the most destructive derecho event on record. In this presentation, we will examine forecast sensitivity to different model initial conditions, and try to understand the important features that may contribute to the success of the forecast.

  18. Modelling Conditional and Unconditional Heteroskedasticity with Smoothly Time-Varying Structure

    DEFF Research Database (Denmark)

    Amado, Christina; Teräsvirta, Timo

    multiplier type misspecification tests. Finite-sample properties of these procedures and tests are examined by simulation. An empirical application to daily stock returns and another one to daily exchange rate returns illustrate the functioning and properties of our modelling strategy in practice......In this paper, we propose two parametric alternatives to the standard GARCH model. They allow the conditional variance to have a smooth time-varying structure of either ad- ditive or multiplicative type. The suggested parameterizations describe both nonlinearity and structural change...... in the conditional and unconditional variances where the transition between regimes over time is smooth. A modelling strategy for these new time-varying parameter GARCH models is developed. It relies on a sequence of Lagrange multiplier tests, and the adequacy of the estimated models is investigated by Lagrange...

  19. Improving Delay-Range-Dependent Stability Condition for Systems with Interval Time-Varying Delay

    Directory of Open Access Journals (Sweden)

    Wei Qian

    2013-01-01

    Full Text Available This paper discusses the delay-range-dependent stability for systems with interval time-varying delay. Through defining the new Lyapunov-Krasovskii functional and estimating the derivative of the LKF by introducing new vectors, using free matrices and reciprocally convex approach, the new delay-range-dependent stability conditions are obtained. Two well-known examples are given to illustrate the less conservatism of the proposed theoretical results.

  20. Protostellar formation in rotating interstellar clouds. VI. Nonuniform initial conditions

    International Nuclear Information System (INIS)

    Boss, A.P.

    1987-01-01

    The collapse and fragmentation of rotating protostellar clouds is explored, starting from nonuniform density and nonuniform rotation initial conditions. Whether binary fragmentation occurs during the first dynamic collapse phase depends strongly on the initial density profile. Exponential clouds are only somewhat more resistant to fragmentation than uniform-density clouds, but power-law clouds do not undergo fragmentation for likely values of a relevant parameter. Because binary fragments start from profiles intermediate between uniform density and exponential clouds, minimum protostellar mass for population I stars should be increased to approximately 0.02 solar mass. The axisymmetric Terey et al. (1984) model should be stable with respect to nonaxisymmetric perturbations. Considering the observed binary frequency, collapse from power-law initial conditions appears to be less common than collapse from more uniform initial conditions. 34 references

  1. Sex differences in in-group cooperation vary dynamically with competitive conditions and outcomes.

    Science.gov (United States)

    Bailey, Drew H; Winegard, Benjamin; Oxford, Jon; Geary, David C

    2012-03-18

    Men's but not women's investment in a public goods game varied dynamically with the presence or absence of a perceived out-group. Three hundred fifty-four (167 male) young adults participated in multiple iterations of a public goods game under intergroup and individual competition conditions. Participants received feedback about whether their investments in the group were sufficient to earn a bonus to be shared among all in-group members. Results for the first trial confirm previous research in which men's but not women's investments were higher when there was a competing out-group. We extended these findings by showing that men's investment in the in-group varied dynamically by condition depending on the outcome of the previous trial: In the group condition, men, but not women, decreased spending following a win (i.e., earning an in-group bonus). In the individual condition, men, but not women, increased spending following a win. We hypothesize that these patterns reflect a male bias to calibrate their level of in-group investment such that they sacrifice only what is necessary for their group to successfully compete against a rival group.

  2. Sex Differences in In-Group Cooperation Vary Dynamically with Competitive Conditions and Outcomes

    Directory of Open Access Journals (Sweden)

    Drew H. Bailey

    2012-01-01

    Full Text Available Men's but not women's investment in a public goods game varied dynamically with the presence or absence of a perceived out-group. Three hundred fifty-four (167 male young adults participated in multiple iterations of a public goods game under intergroup and individual competition conditions. Participants received feedback about whether their investments in the group were sufficient to earn a bonus to be shared among all in-group members. Results for the first trial confirm previous research in which men's but not women's investments were higher when there was a competing out-group. We extended these findings by showing that men's investment in the in-group varied dynamically by condition depending on the outcome of the previous trial: In the group condition, men, but not women, decreased spending following a win (i.e., earning an in-group bonus. In the individual condition, men, but not women, increased spending following a win. We hypothesize that these patterns reflect a male bias to calibrate their level of in-group investment such that they sacrifice only what is necessary for their group to successfully compete against a rival group.

  3. The effect of varying talker identity and listening conditions on gaze behavior during audiovisual speech perception.

    Science.gov (United States)

    Buchan, Julie N; Paré, Martin; Munhall, Kevin G

    2008-11-25

    During face-to-face conversation the face provides auditory and visual linguistic information, and also conveys information about the identity of the speaker. This study investigated behavioral strategies involved in gathering visual information while watching talking faces. The effects of varying talker identity and varying the intelligibility of speech (by adding acoustic noise) on gaze behavior were measured with an eyetracker. Varying the intelligibility of the speech by adding noise had a noticeable effect on the location and duration of fixations. When noise was present subjects adopted a vantage point that was more centralized on the face by reducing the frequency of the fixations on the eyes and mouth and lengthening the duration of their gaze fixations on the nose and mouth. Varying talker identity resulted in a more modest change in gaze behavior that was modulated by the intelligibility of the speech. Although subjects generally used similar strategies to extract visual information in both talker variability conditions, when noise was absent there were more fixations on the mouth when viewing a different talker every trial as opposed to the same talker every trial. These findings provide a useful baseline for studies examining gaze behavior during audiovisual speech perception and perception of dynamic faces.

  4. Understanding and simulating vibrations of plain bridge cables under varying meteorological conditions

    DEFF Research Database (Denmark)

    Matteoni, Giulia

    amplitude peak to peak amplitudes, occurred. This latter behaviour was likely to be associated to dry inclined galloping. Passive dynamic wind tunnel tests were finally undertaken in presence of rain, using the same cable model as adopted in the dry state. The tests served to improve the current......The dissertation investigates the phenomenon of wind induced vibration of bridge cables under varying meteorological conditions. A twin research approach is adopted, where wind tunnel investigation of full-scale bridge cable section models is paralleled with theoretical modelling. A literature......-scale monitoring, wind tunnel testing and theoretical modelling. An extensive wind tunnel test campaign was then undertaken in order to further understand the onset conditions and characteristics of instability in the different climatic conditions described in the literature. Tests were separated into two...

  5. Differences in displayed pump flow compared to measured flow under varying conditions during simulated cardiopulmonary bypass.

    LENUS (Irish Health Repository)

    Hargrove, M

    2008-07-01

    Errors in blood flow delivery due to shunting have been reported to reduce flow by, potentially, up to 40-83% during cardiopulmonary bypass. The standard roller-pump measures revolutions per minute and a calibration factor for different tubing sizes calculates and displays flow accordingly. We compared displayed roller-pump flow with ultrasonically measured flow to ascertain if measured flow correlated with the heart-lung pump flow reading. Comparison of flows was measured under varying conditions of pump run duration, temperature, viscosity, varying arterial\\/venous loops, occlusiveness, outlet pressure, use of silicone or polyvinyl chloride (PVC) in the roller race, different tubing diameters, and use of a venous vacuum-drainage device.

  6. Pre-Swirl Stator and Propeller Design for Varying Operating Conditions

    DEFF Research Database (Denmark)

    Saettone, Simone; Regener, Pelle Bo; Andersen, Poul

    2016-01-01

    blades ahead of the propeller.This paper describes the hydrodynamic design of apre-swirl stator with radially variable pitch, paired with aconventional propeller. The aim is to achieve the highest possible effciency in various operating conditions, and to avoid effciency penalties in off-design operation.......To investigate the propeller and stator designs and configurations in different operating conditions, the computationally inexpensive vortex-lattice method is used a sa first step to optimize the geometry in an initial parameter study. Then the flow over hull, stator and propelleris simulated in a CFD...

  7. An in vitro experimental study of flow past aortic valve under varied pulsatile conditions

    Science.gov (United States)

    Zhang, Ruihang; Zhang, Yan

    2017-11-01

    Flow past aortic valve represents a complex fluid-structure interaction phenomenon that involves pulsatile, vortical, and turbulent conditions. The flow characteristics immediately downstream of the valve, such as the variation of pulsatile flow velocity, formation of vortices, distribution of shear stresses, are of particular interest to further elucidate the role of hemodynamics in various aortic diseases. However, the fluid dynamics of a realistic aortic valve is not fully understood. Particularly, it is unclear how the flow fields downstream of the aortic valve would change under varied pulsatile inlet boundary conditions. In this study, an in vitro experiment has been conducted to investigate the flow fields downstream of a silicone aortic valve model within a cardiovascular flow simulator. Phased-locked Particle Image Velocimetry measurements were performed to map the velocity fields and Reynolds normal and shear stresses at different phases in a cardiac cycle. Temporal variations of pressure across the valve model were measured using high frequency transducers. Results have been compared for different pulsatile inlet conditions, including varied frequencies (heart rates), magnitudes (stroke volumes), and cardiac contractile functions (shapes of waveforms).

  8. Applicability of common stomatal conductance models in maize under varying soil moisture conditions.

    Science.gov (United States)

    Wang, Qiuling; He, Qijin; Zhou, Guangsheng

    2018-07-01

    In the context of climate warming, the varying soil moisture caused by precipitation pattern change will affect the applicability of stomatal conductance models, thereby affecting the simulation accuracy of carbon-nitrogen-water cycles in ecosystems. We studied the applicability of four common stomatal conductance models including Jarvis, Ball-Woodrow-Berry (BWB), Ball-Berry-Leuning (BBL) and unified stomatal optimization (USO) models based on summer maize leaf gas exchange data from a soil moisture consecutive decrease manipulation experiment. The results showed that the USO model performed best, followed by the BBL model, BWB model, and the Jarvis model performed worst under varying soil moisture conditions. The effects of soil moisture made a difference in the relative performance among the models. By introducing a water response function, the performance of the Jarvis, BWB, and USO models improved, which decreased the normalized root mean square error (NRMSE) by 15.7%, 16.6% and 3.9%, respectively; however, the performance of the BBL model was negative, which increased the NRMSE by 5.3%. It was observed that the models of Jarvis, BWB, BBL and USO were applicable within different ranges of soil relative water content (i.e., 55%-65%, 56%-67%, 37%-79% and 37%-95%, respectively) based on the 95% confidence limits. Moreover, introducing a water response function, the applicability of the Jarvis and BWB models improved. The USO model performed best with or without introducing the water response function and was applicable under varying soil moisture conditions. Our results provide a basis for selecting appropriate stomatal conductance models under drought conditions. Copyright © 2018 Elsevier B.V. All rights reserved.

  9. Modelling of the diffusion of pollutants in the atmosphere under varying conditions in large cultivated regions

    International Nuclear Information System (INIS)

    Wueneke, C.D.; Schultz, H.

    1975-01-01

    The most important routines of a numerical code based on the particle-in-cell-method for calculating the transport and the turbulent dispersion of inert and radio-active pollutants in the atmosphere have been programmed and have been tested successfully on the CDC computer CYBER 73/76 of the Regional Computer Centre for Niedersachsen in Hanover. Compared to the Gaussian plume model such a numerical code based on the particle-in-cell-method offers several advantages for the computation of the diffusion under varying conditions in large cultivated regions. (orig.) [de

  10. On specification of initial conditions in turbulence models

    Energy Technology Data Exchange (ETDEWEB)

    Rollin, Bertrand [Los Alamos National Laboratory; Andrews, Malcolm J [Los Alamos National Laboratory

    2010-12-01

    Recent research has shown that initial conditions have a significant influence on the evolution of a flow towards turbulence. This important finding offers a unique opportunity for turbulence control, but also raises the question of how to properly specify initial conditions in turbulence models. We study this problem in the context of the Rayleigh-Taylor instability. The Rayleigh-Taylor instability is an interfacial fluid instability that leads to turbulence and turbulent mixing. It occurs when a light fluid is accelerated in to a heavy fluid because of misalignment between density and pressure gradients. The Rayleigh-Taylor instability plays a key role in a wide variety of natural and man-made flows ranging from supernovae to the implosion phase of Inertial Confinement Fusion (ICF). Our approach consists of providing the turbulence models with a predicted profile of its key variables at the appropriate time in accordance to the initial conditions of the problem.

  11. Chaotic inflation as an attractor in initial-condition space

    International Nuclear Information System (INIS)

    Kung, J.H.; Brandenberger, R.H.

    1990-01-01

    We study the evolution of scalar field inhomogeneities in the preinflationary phase of an inflationary universe. We decompose the scalar field configuration in Fourier modes and consider initial conditions in which more than one mode is excited. We find that the long-wavelength modes are stable against perturbations due to short-wavelength excitations and that chaotic inflation results even if at the initial time the short waves contain most of the energy density

  12. Multipoint propagators for non-Gaussian initial conditions

    International Nuclear Information System (INIS)

    Bernardeau, Francis; Sefusatti, Emiliano; Crocce, Martin

    2010-01-01

    We show here how renormalized perturbation theory calculations applied to the quasilinear growth of the large-scale structure can be carried on in presence of primordial non-Gaussian (PNG) initial conditions. It is explicitly demonstrated that the series reordering scheme proposed in Bernardeau, Crocce, and Scoccimarro [Phys. Rev. D 78, 103521 (2008)] is preserved for non-Gaussian initial conditions. This scheme applies to the power spectrum and higher-order spectra and is based on a reorganization of the contributing terms into the sum of products of multipoint propagators. In case of PNG, new contributing terms appear, the importance of which is discussed in the context of current PNG models. The properties of the building blocks of such resummation schemes, the multipoint propagators, are then investigated. It is first remarked that their expressions are left unchanged at one-loop order irrespective of statistical properties of the initial field. We furthermore show that the high-momentum limit of each of these propagators can be explicitly computed even for arbitrary initial conditions. They are found to be damped by an exponential cutoff whose expression is directly related to the moment generating function of the one-dimensional displacement field. This extends what had been established for multipoint propagators for Gaussian initial conditions. Numerical forms of the cutoff are shown for the so-called local model of PNG.

  13. Positive and negative variations in capacitive images for given defects under varying experimental conditions

    Science.gov (United States)

    Li, Chen; Yin, Xiaokang; Li, Zhen; Li, Wei; Chen, Guoming

    2018-04-01

    Capacitive imaging (CI) technique is a novel electromagnetic NDE technique. The Quasi-static electromagnetic field from the carefully designed electrode pair will vary when the electrical properties of the sample change, leading to the possibility of imaging. It is observed that for a given specimen, the targeted features appear as different variations in capacitive images under different experimental conditions. In some cases, even opposite variations occur, which brings confusion to indication interpretation. It is thus thought interesting to embark on investigations into the cause and effects of the negative variation phenomenon. In this work, the positive and negative variations were first explained from the measurement sensitivity distribution perspective. This was then followed by a detailed analysis using finite element models in COMSOL. A parametric experimental study on a glass fiber composite plate with artificial defects was then carried out to investigate how the experimental conditions affect the variation.

  14. Assessment of a surface-layer parameterization scheme in an atmospheric model for varying meteorological conditions

    Directory of Open Access Journals (Sweden)

    T. J. Anurose

    2014-06-01

    Full Text Available The performance of a surface-layer parameterization scheme in a high-resolution regional model (HRM is carried out by comparing the model-simulated sensible heat flux (H with the concurrent in situ measurements recorded at Thiruvananthapuram (8.5° N, 76.9° E, a coastal station in India. With a view to examining the role of atmospheric stability in conjunction with the roughness lengths in the determination of heat exchange coefficient (CH and H for varying meteorological conditions, the model simulations are repeated by assigning different values to the ratio of momentum and thermal roughness lengths (i.e. z0m/z0h in three distinct configurations of the surface-layer scheme designed for the present study. These three configurations resulted in differential behaviour for the varying meteorological conditions, which is attributed to the sensitivity of CH to the bulk Richardson number (RiB under extremely unstable, near-neutral and stable stratification of the atmosphere.

  15. Analysis of grain filling process to the varied meteorological conditions in winter wheat [Triticum aestivum] cultivars

    International Nuclear Information System (INIS)

    Inoue, K.; Nakazono, K.; Wakiyama, Y.

    2005-01-01

    This paper describes effects of varied meteorological conditions on the grain filling periods, stabilities of yield and quality of winter wheat cultivars with different maturity characteristics (cv. Ayahikari, Norin61, Bandowase, and Tsurupikari). In the field experiments, the meteorological treatments were made during the first heading time on 17 April 2001 and the middle heading time on 24 April 2000. Air temperature, global solar radiation and soil moisture were controlled using a rain shelter, cheesecloth and irrigation system. The growth speed and growth period of wheat grains varied among four winter wheat cultivars, depending on meteorological conditions. The growth speed increased within 1 8.4 deg C of mean air temperature over the 30 days after the anthesis. On the other hand, it was found that the growth speed of wheat grains and the maximum number of wheat grains (Ymax) decreased greatly with the 44.4% interception of global solar radiation. Logistic functions were fitted to the relationship between the relative thousand-kernel-weight (Y/Ymax) and the total integrated temperature (sigmaTa) after heading for all treatment conditions. The maximum weight of grains (Ymax) achieved at the harvest time varied somewhat clearly among four winter wheat cultivars and meteorological conditions. Multiple regression analysis showed that the grain yield (Ymax) of four wheat cultivars correlated positively with daily mean solar radiation. It was also found that the cultivar Ayahikari had a highly significant negative correlation between its grain weight and soil moisture. Namely, the grain weight of high soil moisture plot with pF=1.5 was lower by about 9% than that of a control plot with pF=3.5. On the other hand, the grain yield of cultivar Norin61 responded inversely to a wet environment, indicating that its grain weight was higher for high soil moisture and high wet-bulb temperature than for a dry environment. The grain yield of early varieties of Bandowase and

  16. A new equilibrium torus solution and GRMHD initial conditions

    Science.gov (United States)

    Penna, Robert F.; Kulkarni, Akshay; Narayan, Ramesh

    2013-11-01

    Context. General relativistic magnetohydrodynamic (GRMHD) simulations are providing influential models for black hole spin measurements, gamma ray bursts, and supermassive black hole feedback. Many of these simulations use the same initial condition: a rotating torus of fluid in hydrostatic equilibrium. A persistent concern is that simulation results sometimes depend on arbitrary features of the initial torus. For example, the Bernoulli parameter (which is related to outflows), appears to be controlled by the Bernoulli parameter of the initial torus. Aims: In this paper, we give a new equilibrium torus solution and describe two applications for the future. First, it can be used as a more physical initial condition for GRMHD simulations than earlier torus solutions. Second, it can be used in conjunction with earlier torus solutions to isolate the simulation results that depend on initial conditions. Methods: We assume axisymmetry, an ideal gas equation of state, constant entropy, and ignore self-gravity. We fix an angular momentum distribution and solve the relativistic Euler equations in the Kerr metric. Results: The Bernoulli parameter, rotation rate, and geometrical thickness of the torus can be adjusted independently. Our torus tends to be more bound and have a larger radial extent than earlier torus solutions. Conclusions: While this paper was in preparation, several GRMHD simulations appeared based on our equilibrium torus. We believe it will continue to provide a more realistic starting point for future simulations.

  17. Basic regulatory principles of Escherichia coli's electron transport chain for varying oxygen conditions.

    Science.gov (United States)

    Henkel, Sebastian G; Ter Beek, Alexander; Steinsiek, Sonja; Stagge, Stefan; Bettenbrock, Katja; de Mattos, M Joost Teixeira; Sauter, Thomas; Sawodny, Oliver; Ederer, Michael

    2014-01-01

    For adaptation between anaerobic, micro-aerobic and aerobic conditions Escherichia coli's metabolism and in particular its electron transport chain (ETC) is highly regulated. Although it is known that the global transcriptional regulators FNR and ArcA are involved in oxygen response it is unclear how they interplay in the regulation of ETC enzymes under micro-aerobic chemostat conditions. Also, there are diverse results which and how quinones (oxidised/reduced, ubiquinone/other quinones) are controlling the ArcBA two-component system. In the following a mathematical model of the E. coli ETC linked to basic modules for substrate uptake, fermentation product excretion and biomass formation is introduced. The kinetic modelling focusses on regulatory principles of the ETC for varying oxygen conditions in glucose-limited continuous cultures. The model is based on the balance of electron donation (glucose) and acceptance (oxygen or other acceptors). Also, it is able to account for different chemostat conditions due to changed substrate concentrations and dilution rates. The parameter identification process is divided into an estimation and a validation step based on previously published and new experimental data. The model shows that experimentally observed, qualitatively different behaviour of the ubiquinone redox state and the ArcA activity profile in the micro-aerobic range for different experimental conditions can emerge from a single network structure. The network structure features a strong feed-forward effect from the FNR regulatory system to the ArcBA regulatory system via a common control of the dehydrogenases of the ETC. The model supports the hypothesis that ubiquinone but not ubiquinol plays a key role in determining the activity of ArcBA in a glucose-limited chemostat at micro-aerobic conditions.

  18. Mapping and simulating systematics due to spatially varying observing conditions in DES science verification data

    International Nuclear Information System (INIS)

    Leistedt, B.; Peiris, H. V.; Elsner, F.; Benoit-Lévy, A.; Amara, A.

    2016-01-01

    Spatially varying depth and the characteristics of observing conditions, such as seeing, airmass, or sky background, are major sources of systematic uncertainties in modern galaxy survey analyses, particularly in deep multi-epoch surveys. We present a framework to extract and project these sources of systematics onto the sky, and apply it to the Dark Energy Survey (DES) to map the observing conditions of the Science Verification (SV) data. The resulting distributions and maps of sources of systematics are used in several analyses of DES–SV to perform detailed null tests with the data, and also to incorporate systematics in survey simulations. We illustrate the complementary nature of these two approaches by comparing the SV data with BCC-UFig, a synthetic sky catalog generated by forward-modeling of the DES–SV images. We analyze the BCC-UFig simulation to construct galaxy samples mimicking those used in SV galaxy clustering studies. We show that the spatially varying survey depth imprinted in the observed galaxy densities and the redshift distributions of the SV data are successfully reproduced by the simulation and are well-captured by the maps of observing conditions. The combined use of the maps, the SV data, and the BCC-UFig simulation allows us to quantify the impact of spatial systematics on N(z), the redshift distributions inferred using photometric redshifts. We conclude that spatial systematics in the SV data are mainly due to seeing fluctuations and are under control in current clustering and weak-lensing analyses. However, they will need to be carefully characterized in upcoming phases of DES in order to avoid biasing the inferred cosmological results. Finally, the framework presented here is relevant to all multi-epoch surveys and will be essential for exploiting future surveys such as the Large Synoptic Survey Telescope, which will require detailed null tests and realistic end-to-end image simulations to correctly interpret the deep, high

  19. Bayesian recovery of the initial condition for the heat equation

    NARCIS (Netherlands)

    Knapik, B.T.; Vaart, van der A.W.; Zanten, van J.H.

    2011-01-01

    We study a Bayesian approach to recovering the initial condition for the heat equation from noisy observations of the solution at a later time. We consider a class of prior distributions indexed by a parameter quantifying "smoothness" and show that the corresponding posterior distributions contract

  20. Star formation in mergers with comologically motivated initial conditions

    NARCIS (Netherlands)

    Karman, Wouter; Macciò, Andrea V.; Kannan, Rahul; Moster, Benjamin P.; Somerville, Rachel S.

    2015-01-01

    We use semi-analytic models and cosmological merger trees to provide the initial conditions for multimerger numerical hydrodynamic simulations, and exploit these simulations to explore the effect of galaxy interaction and merging on star formation (SF). We compute numerical realizations of 12 merger

  1. Classical and quantum initial conditions for Higgs inflation

    Directory of Open Access Journals (Sweden)

    Alberto Salvio

    2015-11-01

    Full Text Available We investigate whether Higgs inflation can occur in the Standard Model starting from natural initial conditions or not. The Higgs has a non-minimal coupling to the Ricci scalar. We confine our attention to the regime where quantum Einstein gravity effects are small in order to have results that are independent of the ultraviolet completion of gravity. At the classical level we find no tuning is required to have successful Higgs inflation, provided the initial homogeneity condition is satisfied. On the other hand, at the quantum level we obtain that the renormalization for large non-minimal coupling requires an additional degree of freedom, unless a tuning of the initial values of the running parameters is made. In order to see that this effect may change the predictions we finally include such degree of freedom in the field content and show that Starobinsky's R2 inflation dominates over Higgs inflation.

  2. Initial locomotor sensitivity to cocaine varies widely among inbred mouse strains.

    Science.gov (United States)

    Wiltshire, T; Ervin, R B; Duan, H; Bogue, M A; Zamboni, W C; Cook, S; Chung, W; Zou, F; Tarantino, L M

    2015-03-01

    Initial sensitivity to psychostimulants can predict subsequent use and abuse in humans. Acute locomotor activation in response to psychostimulants is commonly used as an animal model of initial drug sensitivity and has been shown to have a substantial genetic component. Identifying the specific genetic differences that lead to phenotypic differences in initial drug sensitivity can advance our understanding of the processes that lead to addiction. Phenotyping inbred mouse strain panels are frequently used as a first step for studying the genetic architecture of complex traits. We assessed locomotor activation following a single, acute 20 mg/kg dose of cocaine (COC) in males from 45 inbred mouse strains and observed significant phenotypic variation across strains indicating a substantial genetic component. We also measured levels of COC, the active metabolite, norcocaine and the major inactive metabolite, benzoylecgonine, in plasma and brain in the same set of inbred strains. Pharmacokinetic (PK) and behavioral data were significantly correlated, but at a level that indicates that PK alone does not account for the behavioral differences observed across strains. Phenotypic data from this reference population of inbred strains can be utilized in studies aimed at examining the role of psychostimulant-induced locomotor activation on drug reward and reinforcement and to test theories about addiction processes. Moreover, these data serve as a starting point for identifying genes that alter sensitivity to the locomotor stimulatory effects of COC. © 2015 John Wiley & Sons Ltd and International Behavioural and Neural Genetics Society.

  3. Geographically varying effects of weather on tobacco consumption: implications for health marketing initiatives.

    Science.gov (United States)

    Govind, Rahul; Garg, Nitika; Sun, Wenbin

    2014-01-01

    Weather and its fluctuations have been found to influence the consumption of negative hedonic goods. However, such findings are of limited use to health marketers who cannot control the weather, and hence, its effects. The current research utilizes data obtained at the zip-code level to study geographical variations in the effect of weather on tobacco consumption across the entire continental United States. The results allow health marketers to identify areas that will be most responsive to marketing efforts aimed at curtailing negative hedonic consumption and thus implement more effective, region-specific initiatives.

  4. Detection and classification of alarm threshold violations in condition monitoring systems working in highly varying operational conditions

    Science.gov (United States)

    Strączkiewicz, M.; Barszcz, T.; Jabłoński, A.

    2015-07-01

    All commonly used condition monitoring systems (CMS) enable defining alarm thresholds that enhance efficient surveillance and maintenance of dynamic state of machinery. The thresholds are imposed on the measured values such as vibration-based indicators, temperature, pressure, etc. For complex machinery such as wind turbine (WT) the total number of thresholds might be counted in hundreds multiplied by the number of operational states. All the parameters vary not only due to possible machinery malfunctions, but also due to changes in operating conditions and these changes are typically much stronger than the former ones. Very often, such a behavior may lead to hundreds of false alarms. Therefore, authors propose a novel approach based on parameterized description of the threshold violation. For this purpose the novelty and severity factors are introduced. The first parameter refers to the time of violation occurrence while the second one describes the impact of the indicator-increase to the entire machine. Such approach increases reliability of the CMS by providing the operator with the most useful information of the system events. The idea of the procedure is presented on a simulated data similar to those from a wind turbine.

  5. Detection and classification of alarm threshold violations in condition monitoring systems working in highly varying operational conditions

    International Nuclear Information System (INIS)

    Strączkiewicz, M; Barszcz, T; Jabłoński, A

    2015-01-01

    All commonly used condition monitoring systems (CMS) enable defining alarm thresholds that enhance efficient surveillance and maintenance of dynamic state of machinery. The thresholds are imposed on the measured values such as vibration-based indicators, temperature, pressure, etc. For complex machinery such as wind turbine (WT) the total number of thresholds might be counted in hundreds multiplied by the number of operational states. All the parameters vary not only due to possible machinery malfunctions, but also due to changes in operating conditions and these changes are typically much stronger than the former ones. Very often, such a behavior may lead to hundreds of false alarms. Therefore, authors propose a novel approach based on parameterized description of the threshold violation. For this purpose the novelty and severity factors are introduced. The first parameter refers to the time of violation occurrence while the second one describes the impact of the indicator-increase to the entire machine. Such approach increases reliability of the CMS by providing the operator with the most useful information of the system events. The idea of the procedure is presented on a simulated data similar to those from a wind turbine. (paper)

  6. Effect of initial conditions on combustion generated loads

    International Nuclear Information System (INIS)

    Tieszen, S.R.

    1993-01-01

    This analytical study examines the effect of initial thermodynamic conditions on the loads generated by the combustion of homogeneous hydrogen-air-steam mixtures. The effect of initial temperature, pressure, hydrogen concentration, and steam concentration is evaluated for two cases, (1) constant volume and (2) constant initial pressure. For each case, the Adiabatic, Isochoric, Complete Combustion (AICC), Chapman-Jouguet (CJ), and normally reflected CJ pressures are calculated for a range of hydrogen and steam concentrations representative of the entire flammable regime. For detonation loads, pressure profiles and time-histories are also evaluated in one-dimensional Cartesian geometry. The results show that to a first approximation, the AICC and CJ pressures are directly proportional to the initial density. Increasing the hydrogen concentration up to stoichiometric concentrations significantly increases the AICC, CJ, and reflected CJ pressures. For the constant volume case, the AICC, CJ, and reflected CJ pressures increase with increasing hydrogen concentration on the rich side of stoichiometric concentrations. For the constant initial pressure case, the AICC, CJ, and reflected CJ pressures decrease with increasing hydrogen concentration on the rich side of stoichiometric values. The addition of steam decreases the AICC, CJ, and reflected CJ pressures for the constant initial pressure case, but increases them for the constant volume case. For detonations, the pressure time-histories can be normalized with the AICC pressure and the reverberation time for Cartesion geometry. (orig.)

  7. Risky behavior and its effect on survival: snowshoe hare behavior under varying moonlight conditions

    Science.gov (United States)

    Gigliotti, Laura C.; Diefenbach, Duane R.

    2018-01-01

    Predation and predation risk can exert strong influences on the behavior of prey species. However, risk avoidance behaviors may vary among populations of the same species. We studied a population of snowshoe hares (Lepus americanus) near the southern edge of their range, in Pennsylvania. This population occupies different habitat types, experiences different environmental conditions, and are exposed to different predator species and densities than northern hare populations; therefore, they might exhibit differences in risk avoidance behaviors. We analyzed hare survival, movement rates, and habitat use under different levels of predation risk, as indexed by moonlight. Similar to previous work, we found snowshoe hare survival decreased with increased moon illumination during the winter, but we found differences in behavioral responses to increased predation risk. We found that snowshoe hares did not reduce movement rates during high‐risk nights, but instead found that hares selected areas with denser canopy cover, compared to low‐risk nights. We suggest that behavioral plasticity in response to predation risk allows populations of the same species to respond to localized conditions.

  8. PERT: A Method for Expression Deconvolution of Human Blood Samples from Varied Microenvironmental and Developmental Conditions

    Science.gov (United States)

    Csaszar, Elizabeth; Yu, Mei; Morris, Quaid; Zandstra, Peter W.

    2012-01-01

    The cellular composition of heterogeneous samples can be predicted using an expression deconvolution algorithm to decompose their gene expression profiles based on pre-defined, reference gene expression profiles of the constituent populations in these samples. However, the expression profiles of the actual constituent populations are often perturbed from those of the reference profiles due to gene expression changes in cells associated with microenvironmental or developmental effects. Existing deconvolution algorithms do not account for these changes and give incorrect results when benchmarked against those measured by well-established flow cytometry, even after batch correction was applied. We introduce PERT, a new probabilistic expression deconvolution method that detects and accounts for a shared, multiplicative perturbation in the reference profiles when performing expression deconvolution. We applied PERT and three other state-of-the-art expression deconvolution methods to predict cell frequencies within heterogeneous human blood samples that were collected under several conditions (uncultured mono-nucleated and lineage-depleted cells, and culture-derived lineage-depleted cells). Only PERT's predicted proportions of the constituent populations matched those assigned by flow cytometry. Genes associated with cell cycle processes were highly enriched among those with the largest predicted expression changes between the cultured and uncultured conditions. We anticipate that PERT will be widely applicable to expression deconvolution strategies that use profiles from reference populations that vary from the corresponding constituent populations in cellular state but not cellular phenotypic identity. PMID:23284283

  9. Assessing the effects of adaptation measures on optimal water resources allocation under varied water availability conditions

    Science.gov (United States)

    Liu, Dedi; Guo, Shenglian; Shao, Quanxi; Liu, Pan; Xiong, Lihua; Wang, Le; Hong, Xingjun; Xu, Yao; Wang, Zhaoli

    2018-01-01

    Human activities and climate change have altered the spatial and temporal distribution of water availability which is a principal prerequisite for allocation of different water resources. In order to quantify the impacts of climate change and human activities on water availability and optimal allocation of water resources, hydrological models and optimal water resource allocation models should be integrated. Given that increasing human water demand and varying water availability conditions necessitate adaptation measures, we propose a framework to assess the effects of these measures on optimal allocation of water resources. The proposed model and framework were applied to a case study of the middle and lower reaches of the Hanjiang River Basin in China. Two representative concentration pathway (RCP) scenarios (RCP2.6 and RCP4.5) were employed to project future climate, and the Variable Infiltration Capacity (VIC) hydrological model was used to simulate the variability of flows under historical (1956-2011) and future (2012-2099) conditions. The water availability determined by simulating flow with the VIC hydrological model was used to establish the optimal water resources allocation model. The allocation results were derived under an extremely dry year (with an annual average water flow frequency of 95%), a very dry year (with an annual average water flow frequency of 90%), a dry year (with an annual average water flow frequency of 75%), and a normal year (with an annual average water flow frequency of 50%) during historical and future periods. The results show that the total available water resources in the study area and the inflow of the Danjiangkou Reservoir will increase in the future. However, the uneven distribution of water availability will cause water shortage problems, especially in the boundary areas. The effects of adaptation measures, including water saving, and dynamic control of flood limiting water levels (FLWLs) for reservoir operation, were

  10. Accurate initial conditions in mixed Dark Matter--Baryon simulations

    CERN Document Server

    Valkenburg, Wessel

    2017-06-01

    We quantify the error in the results of mixed baryon--dark-matter hydrodynamic simulations, stemming from outdated approximations for the generation of initial conditions. The error at redshift 0 in contemporary large simulations, is of the order of few to ten percent in the power spectra of baryons and dark matter, and their combined total-matter power spectrum. After describing how to properly assign initial displacements and peculiar velocities to multiple species, we review several approximations: (1) {using the total-matter power spectrum to compute displacements and peculiar velocities of both fluids}, (2) scaling the linear redshift-zero power spectrum back to the initial power spectrum using the Newtonian growth factor ignoring homogeneous radiation, (3) using longitudinal-gauge velocities with synchronous-gauge densities, and (4) ignoring the phase-difference in the Fourier modes for the offset baryon grid, relative to the dark-matter grid. Three of these approximations do not take into account that ...

  11. No-hair conjectures, primordial shear and protoinflationary initial conditions

    CERN Document Server

    Giovannini, Massimo

    2014-01-01

    Anisotropic inflationary background geometries are analyzed in the context of an extended gauge action where the electric and magnetic susceptibilities are not bound to coincide and depend on the inflaton field. After deriving various classes of solutions with electric and magnetic hairs, we discuss the problem of the initial boundary conditions of the shear parameter and consider a globally neutral plasma as a possible relic of a preinflationary stage of expansion. While electric hairs are washed out by the finite value of the protoinflationary conductivity, magnetic hairs can persist and introduce a tiny amount of shear causing a different inflationary rate of expansion along orthogonal spatial directions. The plasma interactions are a necessary criterion to discriminate between physical and unphysical initial conditions but they are not strictly sufficient to warrant the stability of a given magnetic solution.

  12. Correlated initial condition for an embedded process by time partitioning

    Czech Academy of Sciences Publication Activity Database

    Velický, Bedřich; Kalvová, Anděla; Špička, Václav

    2010-01-01

    Roč. 81, č. 23 (2010), 235116/1-235116/12 ISSN 1098-0121 R&D Projects: GA ČR GA202/08/0361 Institutional research plan: CEZ:AV0Z10100520; CEZ:AV0Z10100521 Keywords : non-equilibrium * Initial conditions * decay of correlations * Green's functions * quantum transport equations Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.772, year: 2010

  13. arXiv Initial Conditions for Critical Higgs Inflation

    CERN Document Server

    Salvio, Alberto

    2018-05-10

    It has been pointed out that a large non-minimal coupling ξ between the Higgs and the Ricci scalar can source higher derivative operators, which may change the predictions of Higgs inflation. A variant, called critical Higgs inflation, employs the near-criticality of the top mass to introduce an inflection point in the potential and lower drastically the value of ξ . We here study whether critical Higgs inflation can occur even if the pre-inflationary initial conditions do not satisfy the slow-roll behavior (retaining translation and rotation symmetries). A positive answer is found: inflation turns out to be an attractor and therefore no fine-tuning of the initial conditions is necessary. A very large initial Higgs time-derivative (as compared to the potential energy density) is compensated by a moderate increase in the initial field value. These conclusions are reached by solving the exact Higgs equation without using the slow-roll approximation. This also allows us to consistently treat the inflection poi...

  14. Neural initialization of audiovisual integration in prereaders at varying risk for developmental dyslexia.

    Science.gov (United States)

    I Karipidis, Iliana; Pleisch, Georgette; Röthlisberger, Martina; Hofstetter, Christoph; Dornbierer, Dario; Stämpfli, Philipp; Brem, Silvia

    2017-02-01

    Learning letter-speech sound correspondences is a major step in reading acquisition and is severely impaired in children with dyslexia. Up to now, it remains largely unknown how quickly neural networks adopt specific functions during audiovisual integration of linguistic information when prereading children learn letter-speech sound correspondences. Here, we simulated the process of learning letter-speech sound correspondences in 20 prereading children (6.13-7.17 years) at varying risk for dyslexia by training artificial letter-speech sound correspondences within a single experimental session. Subsequently, we acquired simultaneously event-related potentials (ERP) and functional magnetic resonance imaging (fMRI) scans during implicit audiovisual presentation of trained and untrained pairs. Audiovisual integration of trained pairs correlated with individual learning rates in right superior temporal, left inferior temporal, and bilateral parietal areas and with phonological awareness in left temporal areas. In correspondence, a differential left-lateralized parietooccipitotemporal ERP at 400 ms for trained pairs correlated with learning achievement and familial risk. Finally, a late (650 ms) posterior negativity indicating audiovisual congruency of trained pairs was associated with increased fMRI activation in the left occipital cortex. Taken together, a short (audiovisual integration in neural systems that are responsible for processing linguistic information in proficient readers. To conclude, the ability to learn grapheme-phoneme correspondences, the familial history of reading disability, and phonological awareness of prereading children account for the degree of audiovisual integration in a distributed brain network. Such findings on emerging linguistic audiovisual integration could allow for distinguishing between children with typical and atypical reading development. Hum Brain Mapp 38:1038-1055, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals

  15. Initial conditions of urban permeable surfaces in rainfall-runoff models using Horton’s infiltration

    DEFF Research Database (Denmark)

    Davidsen, Steffen; Löwe, Roland; Høegh Ravn, Nanna

    2017-01-01

    Infiltration is a key process controlling runoff, but varies depending on antecedent conditions. This study provides estimates on initial conditions for urban permeable surfaces via continuous simulation of the infiltration capacity using historical rain data. An analysis of historical rainfall...... records show that accumulated rainfall prior to large rain events does not depend on the return period of the event. Using an infiltration-runoff model we found that for a typical large rain storm, antecedent conditions in general lead to reduced infiltration capacity both for sandy and clayey soils...... and that there is substantial runoff for return periods above 1–10 years....

  16. Genome-wide transcriptome analysis of soybean primary root under varying water-deficit conditions.

    Science.gov (United States)

    Song, Li; Prince, Silvas; Valliyodan, Babu; Joshi, Trupti; Maldonado dos Santos, Joao V; Wang, Jiaojiao; Lin, Li; Wan, Jinrong; Wang, Yongqin; Xu, Dong; Nguyen, Henry T

    2016-01-15

    Soybean is a major crop that provides an important source of protein and oil to humans and animals, but its production can be dramatically decreased by the occurrence of drought stress. Soybeans can survive drought stress if there is a robust and deep root system at the early vegetative growth stage. However, little is known about the genome-wide molecular mechanisms contributing to soybean root system architecture. This study was performed to gain knowledge on transcriptome changes and related molecular mechanisms contributing to soybean root development under water limited conditions. The soybean Williams 82 genotype was subjected to very mild stress (VMS), mild stress (MS) and severe stress (SS) conditions, as well as recovery from the severe stress after re-watering (SR). In total, 6,609 genes in the roots showed differential expression patterns in response to different water-deficit stress levels. Genes involved in hormone (Auxin/Ethylene), carbohydrate, and cell wall-related metabolism (XTH/lipid/flavonoids/lignin) pathways were differentially regulated in the soybean root system. Several transcription factors (TFs) regulating root growth and responses under varying water-deficit conditions were identified and the expression patterns of six TFs were found to be common across the stress levels. Further analysis on the whole plant level led to the finding of tissue-specific or water-deficit levels specific regulation of transcription factors. Analysis of the over-represented motif of different gene groups revealed several new cis-elements associated with different levels of water deficit. The expression patterns of 18 genes were confirmed byquantitative reverse transcription polymerase chain reaction method and demonstrated the accuracy and effectiveness of RNA-Seq. The primary root specific transcriptome in soybean can enable a better understanding of the root response to water deficit conditions. The genes detected in root tissues that were associated with

  17. Phytoremdiation Species And Their Modification Under By Weed Varying Climatic Condition A Changing Scenario

    Directory of Open Access Journals (Sweden)

    Anita Singh

    2015-08-01

    Full Text Available Abstract The major reasons for environmental contamination are population explosion increase in industrial and other urban activities. One of the consequent effect of these activities is heavy metal pollution. It is one of the serious issue to be discussed by the scientists and academicians that how to solve this problem to protect the environment. As heavy metals are non-biodegradable so they require effective cleanup technology. Most of the traditional methods such as excavation solidification and burial are very costly or they simply involve the isolation of the metals from contaminated sites. Among different technologies phytoremediation is best approach for removing metal contamination from environment. It involves plants to remove detoxify or immobilize metals from environment. Weed plants are found to be play very important role in metal remediation. They get affected by climatic variation which is also a consequent effect of environmental pollution. The physiology of plants as well as physiochemical properties of soil gets affected by varying climatic condition. Therefore the present review gives the information on metal remediation processes and how these process particularly phytoremediation by weed plants get affected by climatic changes.

  18. Asymmetric Vibration of Polar Orthotropic Annular Circular Plates of Quadratically Varying Thickness with Same Boundary Conditions

    Directory of Open Access Journals (Sweden)

    N. Bhardwaj

    2008-01-01

    Full Text Available In the present paper, asymmetric vibration of polar orthotropic annular circular plates of quadratically varying thickness resting on Winkler elastic foundation is studied by using boundary characteristic orthonormal polynomials in Rayleigh-Ritz method. Convergence of the results is tested and comparison is made with results already available in the existing literature. Numerical results for the first ten frequencies for various values of parameters describing width of annular plate, thickness profile, material orthotropy and foundation constant for all three possible combinations of clamped, simply supported and free edge conditions are shown and discussed. It is found that (a higher elastic property in circumferential direction leads to higher stiffness against lateral vibration; (b Lateral vibration characteristics of F-Fplates is more sensitive towards parametric changes in material orthotropy and foundation stiffness than C-C and S-Splates; (c Effect of quadratical thickness variation on fundamental frequency is more significant in cases of C-C and S-S plates than that of F-Fplates. Thickness profile which is convex relative to plate center-line tends to result in higher stiffness of annular plates against lateral vibration than the one which is concave and (d Fundamental mode of vibration of C-C and S-Splates is axisymmetrical while that of F-Fplates is asymmetrical.

  19. Relativistic initial conditions for N-body simulations

    Energy Technology Data Exchange (ETDEWEB)

    Fidler, Christian [Catholic University of Louvain—Center for Cosmology, Particle Physics and Phenomenology (CP3) 2, Chemin du Cyclotron, B-1348 Louvain-la-Neuve (Belgium); Tram, Thomas; Crittenden, Robert; Koyama, Kazuya; Wands, David [Institute of Cosmology and Gravitation, University of Portsmouth, Portsmouth PO1 3FX (United Kingdom); Rampf, Cornelius, E-mail: christian.fidler@uclouvain.be, E-mail: thomas.tram@port.ac.uk, E-mail: rampf@thphys.uni-heidelberg.de, E-mail: robert.crittenden@port.ac.uk, E-mail: kazuya.koyama@port.ac.uk, E-mail: david.wands@port.ac.uk [Institut für Theoretische Physik, Universität Heidelberg, Philosophenweg 16, D–69120 Heidelberg (Germany)

    2017-06-01

    Initial conditions for (Newtonian) cosmological N-body simulations are usually set by re-scaling the present-day power spectrum obtained from linear (relativistic) Boltzmann codes to the desired initial redshift of the simulation. This back-scaling method can account for the effect of inhomogeneous residual thermal radiation at early times, which is absent in the Newtonian simulations. We analyse this procedure from a fully relativistic perspective, employing the recently-proposed Newtonian motion gauge framework. We find that N-body simulations for ΛCDM cosmology starting from back-scaled initial conditions can be self-consistently embedded in a relativistic space-time with first-order metric potentials calculated using a linear Boltzmann code. This space-time coincides with a simple ''N-body gauge'' for z < 50 for all observable modes. Care must be taken, however, when simulating non-standard cosmologies. As an example, we analyse the back-scaling method in a cosmology with decaying dark matter, and show that metric perturbations become large at early times in the back-scaling approach, indicating a breakdown of the perturbative description. We suggest a suitable ''forwards approach' for such cases.

  20. Solutions to the Cosmic Initial Entropy Problem without Equilibrium Initial Conditions

    Directory of Open Access Journals (Sweden)

    Vihan M. Patel

    2017-08-01

    Full Text Available The entropy of the observable universe is increasing. Thus, at earlier times the entropy was lower. However, the cosmic microwave background radiation reveals an apparently high entropy universe close to thermal and chemical equilibrium. A two-part solution to this cosmic initial entropy problem is proposed. Following Penrose, we argue that the evenly distributed matter of the early universe is equivalent to low gravitational entropy. There are two competing explanations for how this initial low gravitational entropy comes about. (1 Inflation and baryogenesis produce a virtually homogeneous distribution of matter with a low gravitational entropy. (2 Dissatisfied with explaining a low gravitational entropy as the product of a ‘special’ scalar field, some theorists argue (following Boltzmann for a “more natural” initial condition in which the entire universe is in an initial equilibrium state of maximum entropy. In this equilibrium model, our observable universe is an unusual low entropy fluctuation embedded in a high entropy universe. The anthropic principle and the fluctuation theorem suggest that this low entropy region should be as small as possible and have as large an entropy as possible, consistent with our existence. However, our low entropy universe is much larger than needed to produce observers, and we see no evidence for an embedding in a higher entropy background. The initial conditions of inflationary models are as natural as the equilibrium background favored by many theorists.

  1. Curvature profiles as initial conditions for primordial black hole formation

    International Nuclear Information System (INIS)

    Polnarev, Alexander G; Musco, Ilia

    2007-01-01

    This work is part of an ongoing research programme to study possible primordial black hole (PBH) formation during the radiation-dominated era of the early universe. Working within spherical symmetry, we specify an initial configuration in terms of a curvature profile, which represents initial conditions for the large amplitude metric perturbations, away from the homogeneous Friedmann-Robertson-Walker model, which are required for PBH formation. Using an asymptotic quasi-homogeneous solution, we relate the curvature profile with the density and velocity fields, which at an early enough time, when the length scale of the configuration is much larger than the cosmological horizon, can be treated as small perturbations of the background values. We present general analytic solutions for the density and velocity profiles. These solutions enable us to consider in a self-consistent way the formation of PBHs in a wide variety of cosmological situations with the cosmological fluid being treated as an arbitrary mixture of different components with different equations of state. We obtain the analytical solutions for the density and velocity profiles as functions of the initial time. We then use two different parametrizations for the curvature profile and follow numerically the evolution of initial configurations

  2. Should tsunami models use a nonzero initial condition for horizontal velocity?

    Science.gov (United States)

    Nava, G.; Lotto, G. C.; Dunham, E. M.

    2017-12-01

    Tsunami propagation in the open ocean is most commonly modeled by solving the shallow water wave equations. These equations require two initial conditions: one on sea surface height and another on depth-averaged horizontal particle velocity or, equivalently, horizontal momentum. While most modelers assume that initial velocity is zero, Y.T. Song and collaborators have argued for nonzero initial velocity, claiming that horizontal displacement of a sloping seafloor imparts significant horizontal momentum to the ocean. They show examples in which this effect increases the resulting tsunami height by a factor of two or more relative to models in which initial velocity is zero. We test this claim with a "full-physics" integrated dynamic rupture and tsunami model that couples the elastic response of the Earth to the linearized acoustic-gravitational response of a compressible ocean with gravity; the model self-consistently accounts for seismic waves in the solid Earth, acoustic waves in the ocean, and tsunamis (with dispersion at short wavelengths). We run several full-physics simulations of subduction zone megathrust ruptures and tsunamis in geometries with a sloping seafloor, using both idealized structures and a more realistic Tohoku structure. Substantial horizontal momentum is imparted to the ocean, but almost all momentum is carried away in the form of ocean acoustic waves. We compare tsunami propagation in each full-physics simulation to that predicted by an equivalent shallow water wave simulation with varying assumptions regarding initial conditions. We find that the initial horizontal velocity conditions proposed by Song and collaborators consistently overestimate the tsunami amplitude and predict an inconsistent wave profile. Finally, we determine tsunami initial conditions that are rigorously consistent with our full-physics simulations by isolating the tsunami waves (from ocean acoustic and seismic waves) at some final time, and backpropagating the tsunami

  3. Influence of initial conditions on rod behaviour during boiling crisis phase following a reactivity initiated accident

    International Nuclear Information System (INIS)

    Georgenthum, V.; Sugiyama, T.

    2010-01-01

    In the frame of their research programs on high burn-up fuel safety, the French Institute for Radioprotection and Nuclear Safety (IRSN) and the Japan Atomic Energy Agency (JAEA) performed a large set of tests devoted to the study of PWR fuel rod behavior during Reactivity Initiated Accident (RIA) respectively in the CABRI reactor and in the NSRR reactor. The reactor test conditions are different in terms of coolant nature, temperature and pressure. In the CABRI reactor, tests were performed until now with sodium coolant at 280 Celsius degrees and 3 bar. In the NSRR reactor most of the tests were performed with stagnant water at 20 C. degrees and atmospheric pressure but recently a new high temperature high pressure capsule has been developed which allows to performed tests at up to 280 Celsius degrees and 70 bar. The paper discusses the influence of test conditions on rod behaviour during boiling phase, based on tests results and SCANAIR code calculations. The study shows that when the boiling crisis is reached, the initial inner and outer rod pressure have an essential impact on the clad straining and possible ballooning. The analysis of the different test conditions makes it possible to discriminate the influence of initial conditions on the different phases of the transient and is useful for modelling and code development. (authors)

  4. Singularity, initial conditions and quantum tunneling in modern cosmology

    International Nuclear Information System (INIS)

    Khalatnikov, I M; Kamenshchik, A Yu

    1998-01-01

    The key problems of modern cosmology, such as the cosmological singularity, initial conditions, and the quantum tunneling hypothesis, are discussed. The relationship between the latest cosmological trends and L D Landau's old ideas is analyzed. Particular attention is given to the oscillatory approach to singularity; quantum tunneling processes determining wave function of the Universe in the presence of a compex scalar field; and the role of quantum corrections in these processes. The classical dynamics of closed models with a real scalar field is investigated from the standpoint of chaotic, fractal, and singularity-avoiding properties. (special issue)

  5. Linear stochastic differential equations with anticipating initial conditions

    DEFF Research Database (Denmark)

    Khalifa, Narjess; Kuo, Hui-Hsiung; Ouerdiane, Habib

    In this paper we use the new stochastic integral introduced by Ayed and Kuo (2008) and the results obtained by Kuo et al. (2012b) to find a solution to a drift-free linear stochastic differential equation with anticipating initial condition. Our solution is based on well-known results from...... classical Itô theory and anticipative Itô formula results from Kue et al. (2012b). We also show that the solution obtained by our method is consistent with the solution obtained by the methods of Malliavin calculus, e.g. Buckdahn and Nualart (1994)....

  6. Initial Development of Four Forest Species in Different Shading Conditions

    Directory of Open Access Journals (Sweden)

    C. C. Silva

    2013-07-01

    Full Text Available Abstract: Evaluated the initial development through destructive and non-destructive sampling, forest species Adenanthera pavonina, Cassia fistula, Parkia pendula and Hymenolobium petraeum, propagated by seeds at different levels of shading screens black poliefinas (0, 50 and 65% , in the region of Sinop, MT. There were no significant interactions between time and level of shading to any variable. Changes in fresh and dry weight at all levels of shading occurred from 30 DAT. The highest rates of growth were observed in 50% shading to A. pavonina, P. pendula and H. petraeum and 65% shading for C. fistula.Keywords: seedling, growth, physiology, climatic conditions.

  7. The influence of spatially and temporally varying oceanographic conditions on meroplanktonic metapopulations

    Science.gov (United States)

    Botsford, L. W.; Moloney, C. L.; Hastings, A.; Largier, J. L.; Powell, T. M.; Higgins, K.; Quinn, J. F.

    We synthesize the results of several modelling studies that address the influence of variability in larval transport and survival on the dynamics of marine metapopulations distributed along a coast. Two important benthic invertebrates in the California Current System (CCS), the Dungeness crab and the red sea urchin, are used as examples of the way in which physical oceanographic conditions can influence stability, synchrony and persistence of meroplanktonic metapopulations. We first explore population dynamics of subpopulations and metapopulations. Even without environmental forcing, isolated local subpopulations with density-dependence can vary on time scales roughly twice the generation time at high adult survival, shifting to annual time scales at low survivals. The high frequency behavior is not seen in models of the Dungeness crab, because of their high adult survival rates. Metapopulations with density-dependent recruitment and deterministic larval dispersal fluctuate in an asynchronous fashion. Along the coast, abundance varies on spatial scales which increase with dispersal distance. Coastwide, synchronous, random environmental variability tends to synchronize these metapopulations. Climate change could cause a long-term increase or decrease in mean larval survival, which in this model leads to greater synchrony or extinction respectively. Spatially managed metapopulations of red sea urchins go extinct when distances between harvest refugia become greater than the scale of larval dispersal. All assessments of population dynamics indicate that metapopulation behavior in general dependes critically on the temporal and spatial nature of larval dispersal, which is largely determined by physical oceanographic conditions. We therfore explore physical influences on larval dispersal patterns. Observed trends in temperature and salinity applied to laboratory-determined responses indicate that natural variability in temperature and salinity can lead to variability in

  8. Effect of Varying Acid Hydrolysis Condition in Gracilaria Sp. Fermentation Using Sasad

    Science.gov (United States)

    Mansuit, H.; Samsuri, M. D. C.; Sipaut, C. S.; Yee, C. F.; Yasir, S. M.; Mansa, R.

    2015-04-01

    Macroalgae or seaweed is being considered as promising feedstock for bioalcohol production due to high polysaccharides content. Polysaccharides can be converted into fermentable sugar through acid hydrolysis pre-treatment. In this study, the potential of using carbohydrate-rich macroalgae, Gracilaria sp. as feedstock for bioalcohol production via various acid hydrolysis conditions prior to the fermentation process was investigated and evaluated. The seaweed used in this research was from the red algae group, using species of Gracilaria sp. which was collected from Sg. Petani Kedah, Malaysia. Pre-treatment of substrate was done using H2SO4 and HCl with molarity ranging from 0.2M to 0.8M. The pretreatment time were varied in the range of 15 to 30 minutes. Fermentation was conducted using Sasad, a local Sabahan fermentation agent as a starter culture. Alcohol extraction was done using a distillation unit. Reducing sugar analysis was done by Benedict test method. Alcohol content analysis was done using specific gravity test. After hydrolysis, it was found out that acid hydrolysis at 0.2M H2SO4 and pre-treated for 20 minutes at 121°C has shown the highest reducing sugar content which has yield (10.06 mg/g) of reducing sugar. It was followed by other samples hydrolysis using 0.4M HCl with 30 minutes pre-treatment and 0.2M H2SO4, 15 minutes pre-treatment with yield of 8.06 mg/g and 5.75 mg/g reducing sugar content respectively. In conclusion, acid hydrolysis of Gracilaria sp. can produce higher reducing sugar yield and thus it can further enhance the bioalcohol production yield. Hence, acid hydrolysis of Gracilaria sp. should be studied more as it is an important step in the bioalcohol production and upscaling process.

  9. Centrifuge model tests of rainfall-induced slope failures for the investigation of the initiation conditions

    Science.gov (United States)

    Matziaris, Vasileios; Marshall, Alec; Yu, Hai-Sui

    2015-04-01

    Rainfall-induced landslides are very common natural disasters which cause damage to properties and infrastructure and may result in the loss of human lives. These phenomena often take place in unsaturated soil slopes and are triggered by the saturation of the soil profile, due to rain infiltration, which leads to a loss of shear strength. The aim of this study is to determine rainfall thresholds for the initiation of landslides under different initial conditions. Model tests of rainfall-induced landslides are conducted in the Nottingham Centre for Geomechanics 50g-T geotechnical centrifuge. Initially unsaturated plane-strain slope models made with fine silica sand are prepared at varying densities at 1g and accommodated within a climatic chamber which provides controlled environmental conditions. During the centrifuge flight at 60g, rainfall events of varying intensity and duration are applied to the slope models causing the initiation of slope failure. The impact of soil state properties and rainfall characteristics on the landslide initiation process are discussed. The variation of pore water pressures within the slope before, during and after simulated rainfall events is recorded using miniature pore pressure transducers buried in the soil model. Slope deformation is determined by using a high-speed camera and digital image analysis techniques.

  10. Multi-Fibre Optode Microsensors: affordable designs for monitoring oxygen in soils under varying environmental conditions

    Science.gov (United States)

    Rezanezhad, F.; Milojevic, T.; Parsons, C. T.; Smeaton, C. M.; Van Cappellen, P.

    2017-12-01

    , where the imaged data is transmitted remotely using a photo-logging system. The MuFO sensor is currently being tested at a Southern Ontario field site in a year-long experiment. Here we present the field and laboratory results of soil O2 monitoring by this newly developed MuFO microsensor system under varying environmental conditions.

  11. Identification of spatially-localized initial conditions via sparse PCA

    Science.gov (United States)

    Dwivedi, Anubhav; Jovanovic, Mihailo

    2017-11-01

    Principal Component Analysis involves maximization of a quadratic form subject to a quadratic constraint on the initial flow perturbations and it is routinely used to identify the most energetic flow structures. For general flow configurations, principal components can be efficiently computed via power iteration of the forward and adjoint governing equations. However, the resulting flow structures typically have a large spatial support leading to a question of physical realizability. To obtain spatially-localized structures, we modify the quadratic constraint on the initial condition to include a convex combination with an additional regularization term which promotes sparsity in the physical domain. We formulate this constrained optimization problem as a nonlinear eigenvalue problem and employ an inverse power-iteration-based method to solve it. The resulting solution is guaranteed to converge to a nonlinear eigenvector which becomes increasingly localized as our emphasis on sparsity increases. We use several fluids examples to demonstrate that our method indeed identifies the most energetic initial perturbations that are spatially compact. This work was supported by Office of Naval Research through Grant Number N00014-15-1-2522.

  12. Exploring Proposals for Resolving the Initial Conditions and Multiverse Problems in Inflation

    Science.gov (United States)

    Panithanpaisal, Nondh; Steinhardt, Paul

    2018-01-01

    The theory of cosmic inflation with the plateau-like potentials for the scalar field is very successful in predicting standard cosmological parameters. However, if the quantum effects are included, the theory inherently contains serious problems, namely, the multiverse problem and the initial conditions problem. It has been suggested in Mukhanov 2015 and Deen et al. 2016 to add a potential wall to the potential, so that the field never reaches the self-reproduction point. We examine these two proposals by varying the positions of the potential wall as well as varying the initial ratios of kinetic energy, potential energy and curvature. We demonstrate that both proposals are fine-tuned, at best, as they suffer from the drift in the predictions of the spectral tilt (ns) and the tensor-to-scalar ratio (r).

  13. Attenuation of organic micropollutants in an urban lowland stream under varying seasonal and hydrological conditions

    Science.gov (United States)

    Jaeger, Anna; Posselt, Malte; Schaper, Jonas; Lewandowski, Jörg

    2017-04-01

    Transport and fate of polar organic micropollutants in urban streams are of increasing concern for urban water management. Appropriate river management techniques may support a river's ability to self-purify. The river Erpe, an urban lowland stream located in Berlin, Germany, receives treated wastewater which increases its discharge up to 4-fold. Numerous micropollutants (e.g. pharmaceuticals, personal care products, performance chemicals) which survive the treatment process are released into the river and threaten ecosystems and aquatic groundwater quality. In the present work the transport of 57 substances was investigated along a 4.7 km stretch of the river with the aim of understanding the influence of varying seasonal and hydrological conditions on micropollutant fate. We hypothesized that particularly transient storage is a main driver of micropollutant attenuation. A Lagrangian sampling scheme was applied to follow water parcels down the river using the diurnal fluctuations of conservative solute concentrations as an intrinsic tracer. Water samples were collected at two (April) and three (June) stations along a 4.7 km reach downstream of the wastewater inflow. In June the experiment was conducted twice, before and after the first stretch was cleared of macrophytes. Each experiment comprised of hourly sample collection for 48 hours, accompanied by discharge measurements and continuous data logging of water-level, -temperature and electric conductivity. The set of micropollutants, which included both parent compounds and transformation products, was analysed by a newly developed direct injection-UHPLC-MS/MS method. The behaviour of individual micropollutants was compound-specific. Carbamazepine and benzotriazole were persistent along the river stretch while substances such as valsartan and metoprolol were attenuated by up to 15% of their original concentration. Interestingly, some transformation products, such as valsartan acid increased in concentration

  14. Effect of Varying Hemodynamic and Vascular Conditions on Fractional Flow Reserve: An In Vitro Study.

    Science.gov (United States)

    Kolli, Kranthi K; Min, James K; Ha, Seongmin; Soohoo, Hilary; Xiong, Guanglei

    2016-06-30

    The aim of this study was to investigate the impact of varying hemodynamic conditions on fractional flow reserve (ratio of pressure distal [Pd] and proximal [Pa] to stenosis under hyperemia) in an in vitro setting. Failure to achieve maximal hyperemia and the choice of hyperemic agents may have differential effects on coronary hemodynamics and, consequently, on the determination of fractional flow reserve. An in vitro flow system was developed to experimentally model the physiological coronary circulation as flow-dependent stenosis resistance in series with variable downstream resistance. Five idealized models with 30% to 70% diameter stenosis severity were fabricated using VeroClear rigid material in an Objet260 Connex printer. Mean aortic pressure was maintained at 7 levels (60-140 mm Hg) from hypotension to hypertension using a needle valve that mimicked adjustable microcirculatory resistance. A range of physiological flow rates was applied by a steady flow pump and titrated by a flow sensor. The pressure drop and the pressure ratio (Pd/Pa) were assessed for the 7 levels of aortic pressure and differing flow rates. The in vitro experimental data were coupled with pressure-flow relationships from clinical data for populations with and without myocardial infarction, respectively, to evaluate fractional flow reserve. The curve for pressure ratio and flow rate demonstrated a quadratic relationship with a decreasing slope. The absolute decrease in fractional flow reserve in the group without myocardial infarction (with myocardial infarction) was on the order of 0.03 (0.02), 0.05 (0.02), 0.07 (0.05), 0.17 (0.13) and 0.20 (0.24), respectively, for 30%, 40%, 50%, 60%, and 70% diameter stenosis, for an increase in aortic pressure from 60 to 140 mm Hg. The fractional flow reserve value, an index of physiological stenosis significance, was observed to decrease with increasing aortic pressure for a given stenosis in this idealized in vitro experiment for vascular

  15. Volatility spillover and time-varying conditional correlation between DDGS, corn, and soybean meal markets

    NARCIS (Netherlands)

    Etienne, Xiaoli L.; Trujillo-Barrera, Andrés; Hoffman, Linwood A.

    2017-01-01

    We find distiller's dried grains with solubles (DDGS) prices to be positively correlated with both corn and soybean meal prices in the long run. However, neither corn nor soybean meal prices respond to deviations from this long-run relationship. We also identify strong time-varying dynamic

  16. Neural plasticity and its initiating conditions in tinnitus.

    Science.gov (United States)

    Roberts, L E

    2018-03-01

    Deafferentation caused by cochlear pathology (which can be hidden from the audiogram) activates forms of neural plasticity in auditory pathways, generating tinnitus and its associated conditions including hyperacusis. This article discusses tinnitus mechanisms and suggests how these mechanisms may relate to those involved in normal auditory information processing. Research findings from animal models of tinnitus and from electromagnetic imaging of tinnitus patients are reviewed which pertain to the role of deafferentation and neural plasticity in tinnitus and hyperacusis. Auditory neurons compensate for deafferentation by increasing their input/output functions (gain) at multiple levels of the auditory system. Forms of homeostatic plasticity are believed to be responsible for this neural change, which increases the spontaneous and driven activity of neurons in central auditory structures in animals expressing behavioral evidence of tinnitus. Another tinnitus correlate, increased neural synchrony among the affected neurons, is forged by spike-timing-dependent neural plasticity in auditory pathways. Slow oscillations generated by bursting thalamic neurons verified in tinnitus animals appear to modulate neural plasticity in the cortex, integrating tinnitus neural activity with information in brain regions supporting memory, emotion, and consciousness which exhibit increased metabolic activity in tinnitus patients. The latter process may be induced by transient auditory events in normal processing but it persists in tinnitus, driven by phantom signals from the auditory pathway. Several tinnitus therapies attempt to suppress tinnitus through plasticity, but repeated sessions will likely be needed to prevent tinnitus activity from returning owing to deafferentation as its initiating condition.

  17. Charging conditions research to increase the initial projected velocity at different initial charge temperatures

    Science.gov (United States)

    Ishchenko, Aleksandr; Burkin, Viktor; Kasimov, Vladimir; Samorokova, Nina; Zykova, Angelica; Diachkovskii, Alexei

    2017-11-01

    The problems of the defense industry occupy the most important place in the constantly developing modern world. The daily development of defense technology does not stop, nor do studies on internal ballistics. The scientists of the whole world are faced with the task of managing the main characteristics of a ballistic experiment. The main characteristics of the ballistic experiment are the maximum pressure in the combustion chamber Pmax and the projected velocity at the time of barrel leaving UM. During the work the combustion law of the new high-energy fuel was determined in a ballistic experiment for different initial temperatures. This combustion law was used for a parametric study of depending Pmax and UM from a powder charge mass and a traveling charge was carried out. The optimal conditions for loading were obtained for improving the initial velocity at pressures up to 600 MPa for different initial temperatures. In this paper, one of the most promising schemes of throwing is considered, as well as a method for increasing the muzzle velocity of a projected element to 3317 m/s.

  18. Estimating time-varying conditional correlations between stock and foreign exchange markets

    Science.gov (United States)

    Tastan, Hüseyin

    2006-02-01

    This study explores the dynamic interaction between stock market returns and changes in nominal exchange rates. Many financial variables are known to exhibit fat tails and autoregressive variance structure. It is well-known that unconditional covariance and correlation coefficients also vary significantly over time and multivariate generalized autoregressive model (MGARCH) is able to capture the time-varying variance-covariance matrix for stock market returns and changes in exchange rates. The model is applied to daily Euro-Dollar exchange rates and two stock market indexes from the US economy: Dow-Jones Industrial Average Index and S&P500 Index. The news impact surfaces are also drawn based on the model estimates to see the effects of idiosyncratic shocks in respective markets.

  19. Multi-Scale Initial Conditions For Cosmological Simulations

    Energy Technology Data Exchange (ETDEWEB)

    Hahn, Oliver; /KIPAC, Menlo Park; Abel, Tom; /KIPAC, Menlo Park /ZAH, Heidelberg /HITS, Heidelberg

    2011-11-04

    We discuss a new algorithm to generate multi-scale initial conditions with multiple levels of refinements for cosmological 'zoom-in' simulations. The method uses an adaptive convolution of Gaussian white noise with a real-space transfer function kernel together with an adaptive multi-grid Poisson solver to generate displacements and velocities following first- (1LPT) or second-order Lagrangian perturbation theory (2LPT). The new algorithm achieves rms relative errors of the order of 10{sup -4} for displacements and velocities in the refinement region and thus improves in terms of errors by about two orders of magnitude over previous approaches. In addition, errors are localized at coarse-fine boundaries and do not suffer from Fourier-space-induced interference ringing. An optional hybrid multi-grid and Fast Fourier Transform (FFT) based scheme is introduced which has identical Fourier-space behaviour as traditional approaches. Using a suite of re-simulations of a galaxy cluster halo our real-space-based approach is found to reproduce correlation functions, density profiles, key halo properties and subhalo abundances with per cent level accuracy. Finally, we generalize our approach for two-component baryon and dark-matter simulations and demonstrate that the power spectrum evolution is in excellent agreement with linear perturbation theory. For initial baryon density fields, it is suggested to use the local Lagrangian approximation in order to generate a density field for mesh-based codes that is consistent with the Lagrangian perturbation theory instead of the current practice of using the Eulerian linearly scaled densities.

  20. Conditional Probabilities in the Excursion Set Theory. Generic Barriers and non-Gaussian Initial Conditions

    CERN Document Server

    De Simone, Andrea; Riotto, Antonio

    2011-01-01

    The excursion set theory, where density perturbations evolve stochastically with the smoothing scale, provides a method for computing the dark matter halo mass function. The computation of the mass function is mapped into the so-called first-passage time problem in the presence of a moving barrier. The excursion set theory is also a powerful formalism to study other properties of dark matter halos such as halo bias, accretion rate, formation time, merging rate and the formation history of halos. This is achieved by computing conditional probabilities with non-trivial initial conditions, and the conditional two-barrier first-crossing rate. In this paper we use the recently-developed path integral formulation of the excursion set theory to calculate analytically these conditional probabilities in the presence of a generic moving barrier, including the one describing the ellipsoidal collapse, and for both Gaussian and non-Gaussian initial conditions. The non-Markovianity of the random walks induced by non-Gaussi...

  1. Linear parameter varying control of wind turbines covering both partial load and full load conditions

    DEFF Research Database (Denmark)

    Østergaard, Kasper Zinck; Stoustrup, Jakob; Brath, Per

    2009-01-01

    operations tend to be ill-conditioned. The paper proposes a controller construction algorithm together with various remedies for improving the numerical conditioning the algorithm.The proposed algorithm is applied to the design of a LPV controller for wind turbines, and a comparison is made with a controller...... designed using classical techniques to conclude that an improvement in performance is obtained for the entire operating envelope....

  2. Numerical simulation of diurnally varying thermal environment in a street canyon under haze-fog conditions

    Science.gov (United States)

    Tan, Zijing; Dong, Jingliang; Xiao, Yimin; Tu, Jiyuan

    2015-10-01

    The impact of haze-fog on surface temperature, flow pattern, pollutant dispersion and pedestrian thermal comfort are investigated using computational fluid dynamics (CFD) approach based on a three-dimensional street canyon model under different haze-fog conditions. In this study, light extinction coefficient (Kex) is adopted to represent haze-fog pollution level. Numerical simulations are performed for different Kex values at four representative time events (1000 LST, 1300 LST, 1600 LST and 2000 LST). The numerical results suggest that the surface temperature is strongly affected by the haze-fog condition. Surface heating induced by the solar radiation is enhanced by haze-fog, as higher surface temperature is observed under thicker haze-fog condition. Moreover, the temperature difference between sunlit and shadow surfaces is reduced, while that for the two shadow surfaces is slightly increased. Therefore, the surface temperature among street canyon facets becomes more evenly distributed under heavy haze-fog conditions. In addition, flow patterns are considerably altered by different haze-fog conditions, especially for the afternoon (1600 LST) case, in which thermal-driven flow has opposite direction as that of the wind-driven flow direction. Consequently, pollutants such as vehicular emissions will accumulate at pedestrian level, and pedestrian thermal comfort may lower under thicker haze-fog condition.

  3. Adaptive observer-based control for an IPMC actuator under varying humidity conditions

    Science.gov (United States)

    Bernat, Jakub; Kolota, Jakub

    2018-05-01

    As ionic polymer metal composites (IPMC) are increasingly applied to mechatronic systems, many new IPMC modeling efforts have been reported in the literature. The demands of rapidly growing technology has generated interest in advancing the intrinsic actuation and sensing capabilities of IPMC. Classical IPMC applications need constant hydration to operate. On the other hand, for IPMCs operating in air, the water content of the polymer varies with the humidity level of the ambient environment, which leads to its strong humidity-dependent behavior. Furthermore, decreasing water content over time plays a crucial role in the effectiveness of IPMC. Therefore, the primary challenge of this work is to accurately model this phenomenon. The principal contribution of the paper is a new IPMC model, which considers the change of moisture content. A novel nonlinear adaptive observer is designed to determine the unknown electric potential and humidity level in the polymer membrane. This approach effectively determines the moisture content of the IPMC during long-term continuous operation in air. This subsequently allows us to develop an effective back-stepping control algorithm that considers varying moisture content. Data from experiments are presented to support the effectiveness of the observation process, which is shown in illustrative examples.

  4. Performance of asphaltic concrete incorporating styrene butadiene rubber subjected to varying aging condition

    Science.gov (United States)

    Salah, Faisal Mohammed; Jaya, Ramadhansyah Putra; Mohamed, Azman; Hassan, Norhidayah Abdul; Rosni, Nurul Najihah Mad; Mohamed, Abdullahi Ali; Agussabti

    2017-12-01

    The influence of styrene butadiene rubber (SBR) on asphaltic concrete properties at different aging conditions was presented in this study. These aging conditions were named as un-aged, short-term, and long-term aging. The conventional asphalt binder of penetration grade 60/70 was used in this work. Four different levels of SBR addition were employed (i.e., 0 %, 1 %, 3 %, and 5 % by binder weight). Asphalt concrete mixes were prepared at selected optimum asphalt content (5 %). The performance was evaluated based on Marshall Stability, resilient modulus, and dynamic creep tests. Results indicated the improving stability and permanent deformation characteristics that the mixes modified with SBR polymer have under aging conditions. The result also showed that the stability, resilient modulus, and dynamic creep tests have the highest rates compared to the short-term aging and un-aged samples. Thus, the use of 5 % SBR can produce more durable asphalt concrete mixtures with better serviceability.

  5. The Metal-Halide Lamp Under Varying Gravity Conditions Measured by Emission and Laser Absorption Spectroscopy

    Science.gov (United States)

    Flikweert, A. J.; Nimalasuriya, T.; Kroesen, G. M. W.; Haverlag, M.; Stoffels, W. W.

    2009-11-01

    Diffusive and convective processes in the metal-halide lamp cause an unwanted axial colour segregation. Convection is induced by gravity. To understand the flow phenomena in the arc discharge lamp it has been investigated under normal laboratory conditions, micro-gravity (ISS and parabolic flights) and hyper-gravity (parabolic flights 2 g, centrifuge 1 g-10 g). The measurement techniques are webcam imaging, and emission and laser absorption spectroscopy. This paper aims to give an overview of the effect of different artificial gravity conditions on the lamp and compares the results from the three measurement techniques.

  6. Experimental study on Kd of 137Cs at varying suspended load conditions

    International Nuclear Information System (INIS)

    Jaison, T.J.; Jain, Abhishek; Patra, A.K.; Ravi, P.M.; Tripathi, R.M.

    2018-01-01

    137 Cs is one of the radionuclide likely to be released through liquid effluents from a nuclear facility. It is soluble in water, but its mobility in aquatic environments is highly retarded by its strong interaction with suspended sediment. The 137 Cs + sorption by suspended load, especially in the subtropics and tropics are not fully understood. Besides, according to IAEA document in emergency situation 137 Cs and 131 I being marker radionuclides, are easier to identify and representative of all the other radionuclides present. Hence a laboratory study is carried out on sorption of 137 Cs with varying silt load, using the upstream lake water and sediments to estimate site specific distribution coefficient (K d )

  7. Basic regulatory principles of Escherichia coli's electron transport chain for varying oxygen conditions

    NARCIS (Netherlands)

    Henkel, S.G.; Ter Beek, A.S.; Steinsiek, S.; Stagge, S.; Bettenbrock, K.; Teixeira De Mattos, M.J.; Sauter, T.; Sawodny, O.; Ederer, M.

    2014-01-01

    For adaptation between anaerobic, micro-aerobic and aerobic conditions Escherichia coli's metabolism and in particular its electron transport chain (ETC) is highly regulated. Although it is known that the global transcriptional regulators FNR and ArcA are involved in oxygen response it is unclear

  8. Adult Tea Green Leafhoppers, Empoasca onukii (Matsuda), Change Behaviors under Varying Light Conditions.

    Science.gov (United States)

    Shi, Longqing; Vasseur, Liette; Huang, Huoshui; Zeng, Zhaohua; Hu, Guiping; Liu, Xin; You, Minsheng

    2017-01-01

    Insect behaviors are often influenced by light conditions including photoperiod, light intensity, and wavelength. Understanding pest insect responses to changing light conditions may help with developing alternative strategies for pest control. Little is known about the behavioral responses of leafhoppers (Hemiptera: Cicadellidae) to light conditions. The behavior of the tea green leafhopper, Empoasca onukii Matsuda, was examined when exposed to different light photoperiods or wavelengths. Observations included the frequency of locomotion and cleaning activities, and the duration of time spent searching. The results suggested that under normal photoperiod both female and male adults were generally more active in darkness (i.e., at night) than in light. In continuous darkness (DD), the locomotion and cleaning events in Period 1 (7:00-19:00) were significantly increased, when compared to the leafhoppers under normal photoperiod (LD). Leafhoppers, especially females, changed their behavioral patterns to a two day cycle under DD. Under continuous illumination (continuous quartz lamp light, yellow light at night, and green light at night), the activities of locomotion, cleaning, and searching were significantly suppressed during the night (19:00-7:00) and locomotion activities of both females and males were significantly increased during the day (7:00-19:00), suggesting a shift in circadian rhythm. Our work suggests that changes in light conditions, including photoperiod and wavelength, can influence behavioral activities of leafhoppers, potentially affecting other life history traits such as reproduction and development, and may serve as a method for leafhopper behavioral control.

  9. Variation formulae for the solutions of delay differential equations with discontinuous initial conditions

    International Nuclear Information System (INIS)

    Kharatishvili, G L; Tadumadze, T A

    2005-01-01

    Variation formulae are proved for solutions of non-linear differential equations with variable delays and discontinuous initial conditions. The discontinuity of the initial condition means that at the initial moment of time the values of the initial function and the trajectory, generally speaking, do not coincide. The formulae obtained contain a new summand connected with the discontinuity of the initial condition and the variation of the initial moment.

  10. The in vitro fitness cost of antimicrobial resistance in Escherichia coli varies with the growth conditions

    DEFF Research Database (Denmark)

    Petersen, Andreas; Aarestrup, Frank Møller; Olsen, John Elmerdahl

    2009-01-01

    The objective of this study was to investigate the influence of stressful growth conditions on the fitness cost of antimicrobial resistance in Escherichia coli BJ4 caused by chromosomal mutations and plasmid acquisition. The fitness cost of chromosomal streptomycin resistance increased......H and at high-salt concentrations. Strains with an impaired rpoS demonstrated a reduced fitness only during growth in a high-salt concentration. In conclusion, it was demonstrated that bacterial fitness cost in association with antimicrobial resistance generally increases under stressful growth conditions....... However, the growth potential of bacteria with antimicrobial resistances did not increase in a straightforward manner in these in vitro experiments and is therefore probably even more difficult to predict in vivo....

  11. Characterization of Transient Plasma Ignition Flame Kernel Growth for Varying Inlet Conditions

    Science.gov (United States)

    2009-12-01

    from Intercity Manufacturing. Without their expertise in precision machining this thesis would not have been possible. Their countless hours spent...somewhere within the combustor due to the time required to produce the required conditions, and will be travelling at near Mach 5 speeds for most...atmospheric pressure. This sudden drop in pressure creates a rarefaction wave that travels forward in the combustor. The blowdown time for a 1 meter long

  12. Detection of respiratory viruses in shelter dogs maintained under varying environmental conditions

    Directory of Open Access Journals (Sweden)

    Francielle Liz Monteiro

    Full Text Available Abstract Three dog shelters in Rio Grande do Sul were investigated for associations between the occurrence of respiratory viruses and shelter environmental conditions. Nasal secretions randomly collected during the cold season were tested via PCR, and this data collection was followed by nucleotide sequencing of the amplicons. In shelter #1 (poor sanitary and nutritional conditions, high animal density and constant contact between dogs, 78% (58/74 of the nasal samples were positive, 35% (26/74 of which were in single infections and 44% (32/74 of which were in coinfections. Shelters #2 and #3 had satisfactory sanitary and nutritional conditions, outdoors exercise areas (#2 and animal clustering by groups (#3. In shelter #2, 9% (3/35 of the samples were positive for Canine parainfluenza virus (CPIV, and 6% (2/35 were positive for Canid herpesvirus 1 (CaHV-1. In shelter #3, 9% (7/77 of the samples were positive for Canine adenovirus type 2 (CAdV-2, and 1% (1/77 were positive for Canine distemper virus (CDV. The amplicon sequences (CPIV and CDV nucleoprotein gene; CAdV-2 E3 gene; CaHV-1 glycoprotein B gene showed 94-100% nucleotide identity with GenBank sequences. Our results demonstrate that CPIV, CAdV-2 and CDV are common in dog shelters and that their frequencies appear to be related with environmental and nutritional conditions. These results indicate the need for control/prevention measures, including vaccination and environmental management, to minimize these infections and improve dog health.

  13. Mobility of Iron-Cyanide Complexes in a Humic Topsoil under Varying Redox Conditions

    Directory of Open Access Journals (Sweden)

    Thilo Rennert

    2009-01-01

    Full Text Available The potentially toxic Fe-CN complexes ferricyanide, [FeIII(CN6]3−, and ferrocyanide, [FeII(CN6]4−, undergo a variety of redox processes in soil, which affect their mobility. We carried out microcosm experiments with suspensions of a humic topsoil (pH 5.3; Corg 107 g kg-1 to which we added ferricyanide (20 mg l-1. We varied the redox potential (EH from −280 to 580 mV by using O2, N2 and glucose. The decrease of EH led to decreasing concentrations of Fe-CN complexes and partial reductive dissolution of (hydrous Fe and Mn oxides. The dynamics of aqueous Fe-CN concentrations was characterized by decreasing concentrations when the pH rose and the EH dropped. We attribute these dependencies to adsorption on organic surfaces, for which such a pH/EH behavior has been shown previously. Adsorption was reversible, because when the pH and EH changed into the opposite direction, desorption occurred. This study demonstrates the possible impact of soil organic matter on the fate of Fe-CN complexes in soil.

  14. Transient response of a polymer electrolyte membrane fuel cell subjected to time-varying modulating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Noorani, S.; Shamim, T. [Michigan-Dearborn Univ., Dearborn, MI (United States). Dept. of Mechanical Engineering

    2009-07-01

    In order for fuel cells to compete with internal combustion engines, they must have significant advantages in terms of overall efficiency, weight, packaging, safety and cost. A key requirement is its ability to operate under highly transient conditions during start-up, acceleration, and deceleration with stable performance. Therefore, a better understanding of fuel cell dynamic behaviour is needed along with better water management and distributions inside the cell. Therefore, this study investigated the effect of transient conditions on water distribution inside a polymer electrolyte membrane (PEM) cell. A macroscopic single-fuel cell based, one-dimensional, isothermal mathematical model was used to study the effect of modulating cell voltage on the water distribution of anode, cathode, catalyst layers, and membrane. Compared to other existing models, this model did not rely on the non-physical assumption of the uptake curve equilibrium between the pore vapour and ionomer water in the catalyst layers. Instead, the transition between the two phases was modeled as a finite-rate equilibration process. The modulating conditions were simulated by forcing the temporal variations in fuel cell voltage. The results revealed that cell voltage modulations cause a departure in the cell behaviour from its steady behaviour, and the finite-rate equilibration between the catalyst vapour and liquid water can be a factor in determining the cell response. The cell response is also affected by the modulating frequency and amplitude. The peak cell response was observed at low frequencies. Keywords: fuel cell, water transport, dynamic behaviour, numerical simulations. 9 refs., 1 tab., 5 figs.

  15. Oral complementary medicine and alternative practitioner use varies across chronic conditions and attitudes to risk

    Directory of Open Access Journals (Sweden)

    Robert J Adams

    2010-11-01

    Full Text Available Robert J Adams1, Sarah L Appleton1, Antonia Cole2, Tiffany K Gill3, Anne W Taylor3, Catherine L Hill11The Health Observatory, 2Rheumatology Unit, 3Population Research and Outcomes Unit, SA Health, The University of Adelaide Discipline of Medicine, Queen Elizabeth Hospital, Woodville, AustraliaObjectives: To determine whether chronic conditions and patient factors, such as risk perception and decision-making preferences, are associated with complementary medicine and alternative practitioner use in a representative longitudinal population cohort.Participants and setting: Analysis of data from Stage 2 of the North West Adelaide Health Study of 3161 adults who attended a study clinic visit in 2004–2006. The main outcome measures were the medications brought by participants to the study clinic visit, chronic health conditions, attitudes to risk, levels of satisfaction with conventional medicine, and preferred decision-making style.Results: At least one oral complementary medicine was used by 27.9% of participants, and 7.3% were visiting alternative practitioners (naturopath, osteopath. Oral complementary medicine use was significantly associated with arthritis, osteoporosis, and mental health conditions, but not with other chronic conditions. Any pattern of complementary medicine use was generally significantly associated with female gender, age at least 45 years, patient-driven decision-making preferences (odds ratio [OR] 1.38, 95% confidence interval [CI]: 1.08–1.77, and frequent general practitioner visits (>five per year; OR 3.62, 95% CI: 2.13–6.17. Alternative practitioner visitors were younger, with higher levels of education (diploma/trade [OR 1.88, 95% CI: 1.28–2.76], bachelor’s degree [OR 1.77, 95% CI: 1.11–2.82], income > $80,000 (OR 2.28, 95% CI: 1.26–4.11, female gender (OR 3.15, 95% CI: 2.19–4.52, joint pain not diagnosed as arthritis (OR 1.68, 95% CI: 1.17–2.41, moderate to severe depressive symptoms (OR 2.15, 95% CI

  16. Nitrous Oxide Production and Fluxes from Coastal Sediments under Varying Environmental Conditions

    Science.gov (United States)

    Ziebis, W.; Wankel, S. D.; de Beer, D.; Dentinger, J.; Buchwald, C.; Charoenpong, C.

    2014-12-01

    Although coastal zones represent important contributors to the increasing levels of atmospheric nitrous oxide (N2O), it is still unclear which role benthic processes play and whether marine sediments represent sinks or sources for N2O, since interactions among closely associated microbial groups lead to a high degree of variability. In addition, coastal areas are extremely dynamic regions, often exposed to increased nutrient loading and conditions of depleted oxygen. We investigated benthic N2O fluxes and how environmental conditions affect N2O production in different sediments at 2 different geographical locations (German Wadden Sea, a California coastal lagoon). At each location, a total of 32 sediment cores were taken in areas that differed in sediment type, organic content and pore-water nutrient concentrations, as well as in bioturbation activity. Parallel cores were incubated under in-situ conditions, low oxygen and increased nitrate levels for 10 days. Zones of N2O production and consumption were identified in intact cores by N2O microprofiles at the beginning and end of the experiments. In a collaborative effort to determine the dominant sources of N2O, samples were taken throughout the course of the experiments for the determination of the isotopic composition of N2O (as well as nitrate, nitrite and ammonium). Our results indicate that both, nitrate addition and low oxygen conditions in the overlying water, caused an increase of subsurface N2O production in most sediments, with a high variability between different sediment types. N2O production in the sediments was accompanied by N2O consumption, reducing the fluxes to the water column. In general, organic rich sediments showed the strongest response to environmental changes with increased production and efflux of N2O into the overlying water. Bioturbation activity added to the complexity of N2O dynamics by an increase in nitrification-denitrification processes, as well as enhanced pore-water transport

  17. Oral complementary medicine and alternative practitioner use varies across chronic conditions and attitudes to risk.

    Science.gov (United States)

    Adams, Robert J; Appleton, Sarah L; Cole, Antonia; Gill, Tiffany K; Taylor, Anne W; Hill, Catherine L

    2010-11-08

    To determine whether chronic conditions and patient factors, such as risk perception and decision-making preferences, are associated with complementary medicine and alternative practitioner use in a representative longitudinal population cohort. Analysis of data from Stage 2 of the North West Adelaide Health Study of 3161 adults who attended a study clinic visit in 2004-2006. The main outcome measures were the medications brought by participants to the study clinic visit, chronic health conditions, attitudes to risk, levels of satisfaction with conventional medicine, and preferred decision-making style. At least one oral complementary medicine was used by 27.9% of participants, and 7.3% were visiting alternative practitioners (naturopath, osteopath). Oral complementary medicine use was significantly associated with arthritis, osteoporosis, and mental health conditions, but not with other chronic conditions. Any pattern of complementary medicine use was generally significantly associated with female gender, age at least 45 years, patient-driven decision-making preferences (odds ratio [OR] 1.38, 95% confidence interval [CI]: 1.08-1.77), and frequent general practitioner visits (>five per year; OR 3.62, 95% CI: 2.13-6.17). Alternative practitioner visitors were younger, with higher levels of education (diploma/trade [OR 1.88, 95% CI: 1.28-2.76], bachelor's degree [OR 1.77, 95% CI: 1.11-2.82], income >$80,000 (OR 2.28, 95% CI: 1.26-4.11), female gender (OR 3.15, 95% CI: 2.19-4.52), joint pain not diagnosed as arthritis (OR 1.68, 95% CI: 1.17-2.41), moderate to severe depressive symptoms (OR 2.15, 95% CI: 1.04-4.46), and risk-taking behavior (3.26, 1.80-5.92), or low-to-moderate risk aversion (OR 2.08, 95% CI: 1.26-4.11). Although there is widespread use of complementary medicines in the Australian community, there are differing patterns of use between those using oral complementary medicines and those using alternative practitioners.

  18. Varied sensitivity to therapy of HIV-1 strains in CD4+ lymphocyte sub-populations upon ART initiation

    Directory of Open Access Journals (Sweden)

    Paxton William A

    2010-12-01

    Full Text Available Abstract Background Although antiretroviral therapy (ART has proven its success against HIV-1, the long lifespan of infected cells and viral latency prevent eradication. In this study we analyzed the sensitivity to ART of HIV-1 strains in naïve, central memory and effector memory CD4+ lymphocyte subsets. Methods From five patients cellular HIV-1 infection levels were quantified before and after initiation of therapy (2-5 weeks. Through sequencing the C2V3 region of the HIV-1 gp120 envelope, we studied the effect of short-term therapy on virus variants derived from naïve, central memory and effector memory CD4+ lymphocyte subsets. Results During short-term ART, HIV-1 infection levels declined in all lymphocyte subsets but not as much as RNA levels in serum. Virus diversity in the naïve and central memory lymphocyte populations remained unchanged, whilst diversity decreased in serum and the effector memory lymphocytes. ART differentially affected the virus populations co-circulating in one individual harboring a dual HIV-1 infection. Changes in V3 charge were found in all individuals after ART initiation with increases within the effector memory subset and decreases found in the naïve cell population. Conclusions During early ART virus diversity is affected mainly in the serum and effector memory cell compartments. Differential alterations in V3 charge were observed between effector memory and naïve populations. While certain cell populations can be targeted preferentially during early ART, some virus strains demonstrate varied sensitivity to therapy, as shown from studying two strains within a dual HIV-1 infected individual.

  19. Fractal analysis on a classical hard-wall billiard with openings using a two-dimensional set of initial conditions

    International Nuclear Information System (INIS)

    Ree, Suhan

    2003-01-01

    Fractal analysis is performed to measure the chaoticity of a classical hard-wall billiard with openings. We use the circular billiard with a straight cut with two openings, and a two-dimensional (2D) set of initial conditions that produce all possible trajectories of a particle injected from one opening. We numerically compute the fractal dimension of singular points of the function that maps an initial condition to the number of collisions with the wall before the exit, using the box-counting algorithm that uses uniformly distributed points inside the 2D set of initial conditions. Finally, the classical chaotic properties are observed while the parameters of the billiard are varied, and the results are compared with those with the one-dimensional set of initial conditions

  20. Aerodynamic performance of a vibrating piezoelectric fan under varied operational conditions

    International Nuclear Information System (INIS)

    Stafford, J; Jeffers, N

    2014-01-01

    This paper experimentally examines the bulk aerodynamic performance of a vibrating fan operating in the first mode of vibration. The influence of operating condition on the local velocity field has also been investigated to understand the flow distribution at the exit region and determine the stalling condition for vibrating fans. Fan motion has been generated and controlled using a piezoelectric ceramic attached to a stainless steel cantilever. The frequency and amplitude at resonance were 109.4 Hz and 12.5 mm, respectively. A test facility has been developed to measure the pressure-flow characteristics of the vibrating fan and simultaneously conduct local velocity field measurements using particle image velocimetry. The results demonstrate the impact of system characteristics on the local velocity field. High momentum regions generated due to the oscillating motion exist with a component direction that is tangent to the blade at maximum displacement. These high velocity zones are significantly affected by increasing impedance while flow reversal is a dominant feature at maximum pressure rise. The findings outlined provide useful information for design of thermal management solutions that may incorporate this air cooling approach.

  1. Buckling of Nonprismatic Column on Varying Elastic Foundation with Arbitrary Boundary Conditions

    Directory of Open Access Journals (Sweden)

    Ahmad A. Ghadban

    2017-01-01

    Full Text Available Buckling of nonprismatic single columns with arbitrary boundary conditions resting on a nonuniform elastic foundation may be considered as the most generalized treatment of the subject. The buckling differential equation for such columns is extremely difficult to solve analytically. Thus, the authors propose a numerical approach by discretizing the column into a finite number of segments. Each segment has constants E (modulus of elasticity, I (moment of inertia, and β (subgrade stiffness. Next, an exact analytical solution is derived for each prismatic segment resting on uniform elastic foundation. These segments are then assembled in a matrix from which the critical buckling load is obtained. The derived formulation accounts for different end boundary conditions. Validation is performed by benchmarking the present results against analytical solutions found in the literature, showing excellent agreement. After validation, more examples are solved to illustrate the power and flexibility of the proposed method. Overall, the proposed method provides reasonable results, and the examples solved demonstrate the versatility of the developed approach and some of its many possible applications.

  2. Schema bias in source monitoring varies with encoding conditions: support for a probability-matching account.

    Science.gov (United States)

    Kuhlmann, Beatrice G; Vaterrodt, Bianca; Bayen, Ute J

    2012-09-01

    Two experiments examined reliance on schematic knowledge in source monitoring. Based on a probability-matching account of source guessing, a schema bias will only emerge if participants do not have a representation of the source-item contingency in the study list, or if the perceived contingency is consistent with schematic expectations. Thus, the account predicts that encoding conditions that affect contingency detection also affect schema bias. In Experiment 1, the schema bias commonly found when schematic information about the sources is not provided before encoding was diminished by an intentional source-memory instruction. In Experiment 2, the depth of processing of schema-consistent and schema-inconsistent source-item pairings was manipulated. Participants consequently overestimated the occurrence of the pairing type they processed in a deep manner, and their source guessing reflected this biased contingency perception. Results support the probability-matching account of source guessing. PsycINFO Database Record (c) 2012 APA, all rights reserved.

  3. Rimsulfuron in Soil: Effects on Microbiological Properties under Varying Soil Conditions

    Directory of Open Access Journals (Sweden)

    Ljiljana Radivojević

    2011-01-01

    Full Text Available The effects of rimsulfuron a sulfonylurea herbicide on the growth and activity of soil microorganisms under laboratory conditions was investigated in two soils. The application rates were: 0.2, 2.0 and 20.0 mg a.i kg-1 soil. The lowest concentration tested was the label rate (0.2 mg a.i kg-1, and the other two were ten and hundred timeshigher. No adverse effects on microbiological processes were observed for the label rate. Decrease in microbial biomass carbon, dehydrogenase activity, fungi and bacteria in comparison with untreated control, were found at higher rates. The magnitude of these effects were generally slight and transitory.

  4. Demonstration of Aerosol Property Profiling by Multiwavelength Lidar Under Varying Relative Humidity Conditions

    Science.gov (United States)

    Veselovskii, I.; Whiteman, D. N.; Kolgotin, A.; Andrews, E.; Korenskii, M.

    2009-01-01

    During the months of July-August 2007 NASA conducted a research campaign called the Tropical Composition, Clouds and Climate Coupling (TC4) experiment. Vertical profiles of ozone were measured daily using an instrument known as an ozonesonde, which is attached to a weather balloon and launch to altitudes in excess of 30 km. These ozone profiles were measured over coastal Las Tablas, Panama (7.8N, 80W) and several times per week at Alajuela, Costa Rica (ION, 84W). Meteorological systems in the form of waves, detected most prominently in 100-300 in thick ozone layer in the tropical tropopause layer, occurred in 50% (Las Tablas) and 40% (Alajuela) of the soundings. These layers, associated with vertical displacements and classified as gravity waves ("GW," possibly Kelvin waves), occur with similar stricture and frequency over the Paramaribo (5.8N, 55W) and San Cristobal (0.925, 90W) sites of the Southern Hemisphere Additional Ozonesondes (SHADOZ) network. The gravity wave labeled layers in individual soundings correspond to cloud outflow as indicated by the tracers measured from the NASA DC-8 and other aircraft data, confirming convective initiation of equatorial waves. Layers representing quasi-horizontal displacements, referred to as Rossby waves, are robust features in soundings from 23 July to 5 August. The features associated with Rossby waves correspond to extra-tropical influence, possibly stratospheric, and sometimes to pollution transport. Comparison of Las Tablas and Alajuela ozone budgets with 1999-2007 Paramaribo and San Cristobal soundings shows that TC4 is typical of climatology for the equatorial Americas. Overall during TC4, convection and associated meteorological waves appear to dominate ozone transport in the tropical tropopause layer.

  5. Fractional differential equation with the fuzzy initial condition

    Directory of Open Access Journals (Sweden)

    Sadia Arshad

    2011-02-01

    Full Text Available In this paper we study the existence and uniqueness of the solution for a class of fractional differential equation with fuzzy initial value. The fractional derivatives are considered in the Riemann-Liouville sense.

  6. Broccoli (Brassica oleracea var. italica head initiation under field conditions

    Directory of Open Access Journals (Sweden)

    Alina Kałużewicz

    2012-12-01

    Full Text Available A two–year study on the influence of temperature on broccoli head initiation was carried out at the ''Marcelin'' experimental station of the Poznań University of Life Sciences. In each year of the study, plants were planted in the field at four dates. The evaluation of the developmental phase of the broccoli shoot apex was based on the analysis of microscope slides. The date of head initiation was assumed as the day on which the first of the examined apices were found to be at the early generative phase. The plant characteristics (number of leaves, leaf area and stem diameter on the date of initiation were also determined. Variation in length of the period from planting to head initiation was found both between dates of planting and between experimental years. The shortest period from planting to initiation was when the plants were planted in April and June (17-18 days in the first year and the longest one for planting in April in the first year of the study (29 days. The length of the period from planting to head initiation depended on mean daily air temperature. The higher the temperature was, the shorter was the period.

  7. IR radiation characteristics of rocket exhaust plumes under varying motor operating conditions

    Directory of Open Access Journals (Sweden)

    Qinglin NIU

    2017-06-01

    Full Text Available The infrared (IR irradiance signature from rocket motor exhaust plumes is closely related to motor type, propellant composition, burn time, rocket geometry, chamber parameters and flight conditions. In this paper, an infrared signature analysis tool (IRSAT was developed to understand the spectral characteristics of exhaust plumes in detail. Through a finite volume technique, flow field properties were obtained through the solution of axisymmetric Navier-Stokes equations with the Reynolds-averaged approach. A refined 13-species, 30-reaction chemistry scheme was used for combustion effects and a k-ε-Rt turbulence model for entrainment effects. Using flowfield properties as input data, the spectrum was integrated with a line of sight (LOS method based on a single line group (SLG model with Curtis-Godson approximation. The model correctly predicted spectral distribution in the wavelengths of 1.50–5.50 μm and had good agreement for its location with imaging spectrometer data. The IRSAT was then applied to discuss the effects of three operating conditions on IR signatures: (a afterburning; (b chamber pressure from ignition to cutoff; and (c minor changes in the ratio of hydroxyl-terminated polybutadiene (HTPB binder to ammonium perchlorate (AP oxidizer in propellant. Results show that afterburning effects can increase the size and shape of radiance images with enhancement of radiation intensity up to 40%. Also, the total IR irradiance in different bands can be characterized by a non-dimensional chamber pressure trace in which the maximum discrepancy is less than 13% during ignition and engine cutoff. An increase of chamber pressure can lead to more distinct diamonds, whose distance intervals are extended, and the position of the first diamond moving backwards. In addition, an increase in HTPB/AP causes a significant jump in spectral intensity. The incremental rates of radiance intensity integrated in each band are linear with the increase of HTPB

  8. Hydroxyisohexyl 3-cyclohexene carboxaldehyde (lyral) in patch test preparations under varied storage conditions.

    Science.gov (United States)

    Hamann, Dathan; Hamann, Carsten R; Zimerson, Erik; Bruze, Magnus

    2013-01-01

    The common practice of preparing patch tests in advance has recently been called into question by researchers. It has been established that fragrance compounds are volatile and their testing efficacy may be affected by storage conditions and preparation. Allergens in fragrance mix I rapidly decrease in concentration after preapplication to test chambers. This study aimed to investigate the volatility of hydroxyisohexyl 3-cyclohexene carboxaldehyde (HICC) in petrolatum when stored in test chambers and to explore the correlation between vapor pressure and allergen loss in petrolatum during preparation and storage. Standardized HICC in petrolatum was prepared and stored in IQ Chambers and Finn Chambers with covers at 5°C, 25°C, and 35°C, and concentration was analyzed at intervals for up to 9 days using gel permeation chromatography. Changes in HICC concentrations were not statistically significant at 8 hours at 5°C, 25°C, and 35°C. After 9 days, HICC concentrations were found to fall approximately 30% when stored at 35°C, 10% at 25°C, and less than 5% at 5°C. There was no significant difference between IQ and Finn chambers. Hydroxyisohexyl 3-cyclohexene carboxaldehyde concentrations are more stable in petrolatum than many other studied fragrance allergens, but HICC is still at risk for decreasing concentration when exposed to ambient air or heat for prolonged periods.

  9. Vibration Analysis of a Tire in Ground Contact under Varied Conditions

    Directory of Open Access Journals (Sweden)

    Karakus Murat

    2017-03-01

    Full Text Available The effect of three different factors, which are inflation pressure, vertical load and coefficient of friction on the natural frequencies of a tire (175/70 R13 has been studied. A three dimensional tire model is constructed, using four different material properties and parts in the tire. Mechanical properties of the composite parts are evaluated. After investigating the free vibration, contact analysis is carried out. A concrete block and the tire are modelled together, using three different coefficients of friction. Experiments are run under certain conditions to check the accuracy of the numerical model. The natural frequencies are measured to describe free vibration and vibration of the tire contacted by ground, using a damping monitoring method. It is seen, that experimental and numerical results are in good agreement. On the other hand, investigating the impact of three different factors together is quite difficult on the natural frequencies. When some of these factors are assumed to be constant and the variables are taken one by one, it is easier to assess the effects.

  10. Toxicity of pentachlorophenol to aquatic organisms under naturally varying and controlled environmental conditions

    Energy Technology Data Exchange (ETDEWEB)

    Hedtke, S.F.; West, C.W.; Allen, K.N.; Norberg-King, T.J.; Mount, D.I.

    1986-06-01

    The toxicity of pentachlorophenol (PCP) was determined in the laboratory for 11 aquatic species. Tests were conducted seasonally in ambient Mississippi River water and under controlled conditions in Lake Superior water. Fifty-one acute toxicity tests were conducted, with LC50 values ranging from 85 micrograms/L for the white sucker Catastomus commersoni during the summer to greater than 7770 micrograms/L for the isopod Asellus racovitzai during the winter. The effect of PCP on growth and/or reproduction was determined for seven species. The most sensitive chronically exposed organisms were the cladoceran Ceriodaphnia reticulata and the snail Physa gyrina. The greatest variation in toxicity was due to species sensitivity. Within a given, season there was as much as a 40-fold difference in LC50 values between species. For any one species, the maximum variation in LC50 between seasons was approximately 14-fold. There were also substantial differences in acute-chronic relationships, with acute/chronic ratios ranging from greater than 37 for C. reticulata to 1 for Simocephalus vetulus. It is suggested that the composition of the aquatic community should be the most important consideration in estimating the potential environmental effects of PCP.

  11. Comparison of the kinetics of different Markov models for ligand binding under varying conditions

    International Nuclear Information System (INIS)

    Martini, Johannes W. R.; Habeck, Michael

    2015-01-01

    We recently derived a Markov model for macromolecular ligand binding dynamics from few physical assumptions and showed that its stationary distribution is the grand canonical ensemble [J. W. R. Martini, M. Habeck, and M. Schlather, J. Math. Chem. 52, 665 (2014)]. The transition probabilities of the proposed Markov process define a particular Glauber dynamics and have some similarity to the Metropolis-Hastings algorithm. Here, we illustrate that this model is the stochastic analog of (pseudo) rate equations and the corresponding system of differential equations. Moreover, it can be viewed as a limiting case of general stochastic simulations of chemical kinetics. Thus, the model links stochastic and deterministic approaches as well as kinetics and equilibrium described by the grand canonical ensemble. We demonstrate that the family of transition matrices of our model, parameterized by temperature and ligand activity, generates ligand binding kinetics that respond to changes in these parameters in a qualitatively similar way as experimentally observed kinetics. In contrast, neither the Metropolis-Hastings algorithm nor the Glauber heat bath reflects changes in the external conditions correctly. Both converge rapidly to the stationary distribution, which is advantageous when the major interest is in the equilibrium state, but fail to describe the kinetics of ligand binding realistically. To simulate cellular processes that involve the reversible stochastic binding of multiple factors, our pseudo rate equation model should therefore be preferred to the Metropolis-Hastings algorithm and the Glauber heat bath, if the stationary distribution is not of only interest

  12. Comparison of the kinetics of different Markov models for ligand binding under varying conditions

    Energy Technology Data Exchange (ETDEWEB)

    Martini, Johannes W. R., E-mail: jmartin2@gwdg.de [Max Planck Institute for Developmental Biology, Tübingen (Germany); Felix Bernstein Institute for Mathematical Statistics in the Biosciences, University of Göttingen, Göttingen (Germany); Habeck, Michael, E-mail: mhabeck@gwdg.de [Felix Bernstein Institute for Mathematical Statistics in the Biosciences, University of Göttingen, Göttingen (Germany); Max Planck Institute for Biophysical Chemistry, Göttingen (Germany)

    2015-03-07

    We recently derived a Markov model for macromolecular ligand binding dynamics from few physical assumptions and showed that its stationary distribution is the grand canonical ensemble [J. W. R. Martini, M. Habeck, and M. Schlather, J. Math. Chem. 52, 665 (2014)]. The transition probabilities of the proposed Markov process define a particular Glauber dynamics and have some similarity to the Metropolis-Hastings algorithm. Here, we illustrate that this model is the stochastic analog of (pseudo) rate equations and the corresponding system of differential equations. Moreover, it can be viewed as a limiting case of general stochastic simulations of chemical kinetics. Thus, the model links stochastic and deterministic approaches as well as kinetics and equilibrium described by the grand canonical ensemble. We demonstrate that the family of transition matrices of our model, parameterized by temperature and ligand activity, generates ligand binding kinetics that respond to changes in these parameters in a qualitatively similar way as experimentally observed kinetics. In contrast, neither the Metropolis-Hastings algorithm nor the Glauber heat bath reflects changes in the external conditions correctly. Both converge rapidly to the stationary distribution, which is advantageous when the major interest is in the equilibrium state, but fail to describe the kinetics of ligand binding realistically. To simulate cellular processes that involve the reversible stochastic binding of multiple factors, our pseudo rate equation model should therefore be preferred to the Metropolis-Hastings algorithm and the Glauber heat bath, if the stationary distribution is not of only interest.

  13. Effect of Initial Hydraulic Conditions on Capillary Rise in a Porous Medium: Pore-Network Modeling

    KAUST Repository

    Joekar-Niasar, V.; Hassanizadeh, S. M.

    2012-01-01

    The dynamics of capillary rise in a porous medium have been mostly studied in initially dry systems. As initial saturation and initial hydraulic conditions in many natural and industrial porous media can be variable, it is important to investigate

  14. Quantifying uncertainty in Gulf of Mexico forecasts stemming from uncertain initial conditions

    KAUST Repository

    Iskandarani, Mohamed; Le Hé naff, Matthieu; Srinivasan, Ashwanth; Knio, Omar

    2016-01-01

    Polynomial Chaos (PC) methods are used to quantify the impacts of initial conditions uncertainties on oceanic forecasts of the Gulf of Mexico circulation. Empirical Orthogonal Functions are used as initial conditions perturbations with their modal

  15. Modeling Quantum Dot Nanoparticle Fate and Transport in Saturated Porous Media under Varying Flow Conditions

    Science.gov (United States)

    Becker, M. D.; Wang, Y.; Englehart, J.; Pennell, K. D.; Abriola, L. M.

    2010-12-01

    As manufactured nanomaterials become more prevalent in commercial and industrial applications, the development of mathematical models capable of predicting nanomaterial transport and retention in subsurface systems is crucial to assessing their fate and distribution in the environment. A systematic modeling approach based on a modification of clean-bed filtration theory was undertaken to elucidate mechanisms governing the transport and deposition behavior of quantum dots in saturated quartz sand as a function of grain size and flow velocity. The traditional deposition governing equation, which assumes irreversible attachment by a first-order rate (katt), was modified to include a maximum or limiting retention capacity (Smax) and first-order detachment of particles from the solid phase (kdet). Quantum dot mobility experiments were performed in columns packed with three size fractions of Ottawa sand (d50 = 125, 165, and 335 μm) at two different pore-water velocities (0.8 m/d and 7.6 m/d). The CdSe quantum dots in a CdZnS shell and polyacrylic acid coating were negatively charged (zeta potential measured ca. -35 mV) with a hydrodynamic diameter of approximately 30 nm. Fitted values of katt, Smax, and kdet were obtained for each transport and deposition experiment through the implementation of a nonlinear least-squares routine developed to fit the model to experimental breakthrough and retention data via multivariate optimization. Fitted attachment rates and retention capacities increased exponentially with decreasing grain size at both flow rates, while no discernable trend was apparent for the fitted detachment rates. Maximum retention capacity values were plotted against a normalized mass flux expression, which accounts for flow conditions and grain size. A power function fit to the data yielded a dependence that was consistent with a previous study undertaken with fullerene nanoparticles.

  16. Reaction-diffusion fronts with inhomogeneous initial conditions

    Energy Technology Data Exchange (ETDEWEB)

    Bena, I [Departement de Physique Theorique, Universite de Geneve, CH-1211 Geneva 4 (Switzerland); Droz, M [Departement de Physique Theorique, Universite de Geneve, CH-1211 Geneva 4 (Switzerland); Martens, K [Departement de Physique Theorique, Universite de Geneve, CH-1211 Geneva 4 (Switzerland); Racz, Z [Institute for Theoretical Physics, Eoetvoes University, 1117 Budapest (Hungary)

    2007-02-14

    Properties of reaction zones resulting from A+B {yields} C type reaction-diffusion processes are investigated by analytical and numerical methods. The reagents A and B are separated initially and, in addition, there is an initial macroscopic inhomogeneity in the distribution of the B species. For simple two-dimensional geometries, exact analytical results are presented for the time evolution of the geometric shape of the front. We also show using cellular automata simulations that the fluctuations can be neglected both in the shape and in the width of the front.

  17. Initial data release of regular blood drip stain created by varying fall height, angle of impact and source dimension

    Directory of Open Access Journals (Sweden)

    Nabanita Basu

    2016-09-01

    Full Text Available The dataset developed consists of 108 blood drip stains developed with fresh porcine blood, blood admixed with different dosage of Warfarin and Heparin, respectively. For each particular blood type (i.e. fresh blood, blood admixed with Warfarin at different dosage and blood admixed with Heparin at varied dosage stain patterns were created by passive dripping of blood from a 2.5 cm3 subcutaneous syringe with needle filled to capacity, at 30°, 60° and 90° angle of impact with corresponding fall height of 20, 40 and 60 cm respectively. In the other dataset of 162 datapoints, 81 regular drip stains were formed from blood that had dripped passively from a subcutaneous syringe without needle at the aforementioned angle of impact and fall height, while the other stains were formed as a result of dripping of blood from a subcutaneous syringe with needle. In order to compare stains formed, all stains were recorded on the same representative, non-porous, smooth target surface under similar physical conditions. The interpretations relevant to the dataset are available in the article titled ‘2D Source Area prediction based on physical characteristics of a regular, passive blood drip stain’ (Basu and Bandyopadhyay, 2016 [7]. An image pre-processing algorithm for extracting ROI has also been incorporated in this article. Keywords: Drip stain, Bloodstain Pattern Analysis, Source Dimension prediction

  18. Cardiovascular disease markers responses in male receiving improved-fat meat-products vary by initial LDL-cholesterol levels.

    Directory of Open Access Journals (Sweden)

    Paloma Celada

    2016-11-01

    Full Text Available Objectives: Cardiovascular disease (CVD is prevalent in people at high meat-product consumption. To study the effect of consuming different Pâté and Frankfurter formulations on clinical/emergent CVD biomarkers in male volunteers with different initial LDL-cholesterol levels (< and ³ 3.36 mmol/L. Method: Eighteen male volunteers with at least two CVD risk factors were enrolled in a crossover controlled study. Pork-products were consumed during 4wk: reduced-fat (RF, omega-3-enriched-RF (n-3RF, and normal-fat (NF. Pork-products were separated by 4wk washout. Lipids, lipoproteins, oxidized LDL (oxLDL, apolipoproteins (apo and their ratios, homocysteine (tHcys, arylesterase (AE, C-reactive protein (CRP, tumor necrotic factor (TNFa were tested. Results: The rate of change for AE, oxLDL, Lp(a, AE/HDL-cholesterol, LDL/apo B and AE/oxLDL ratios varied (p<0.05 among periods only in volunteers with LDLcholesterol ³3.36 mmol/L. TNFa decreased (p<0.05 among volunteers with low-normal LDL-cholesterol values while AE increased (p<0.01 in high LDL-cholesterol volunteers during the RF-period. AE increased while CRP decreased (both p<0.01 in low-normal LDL-cholesterol volunteers while AE (p<0.001 and apo B (p<0.01 increased in the high LDL-cholesterol group during the n-3RF-period. Total cholesterol (p<0.05 increased in the low/normal LDL-cholesterol group while tHcys decreased (p<0.05 in the high LDL-cholesterol group during the NF-period. Differences in response in volunteers with low-normal vs. high initial LDL-cholesterol levels to the n-3RF but not to the RF meat-products seem evident. Conclusions: Subjects with high LDL-cholesterol seem target for n-3RF products while subjects with LDL-cholesterol <3.36 mmol/L were more negatively affected by NF-products. Any generalization about functional meat product or consumption should be avoided.

  19. Initial Conditions Corresponding to Optimal Ion Acceleration in the VINCY Cyclotron

    International Nuclear Information System (INIS)

    Ilic, A. Z.; Ristic-Djurovic, J. L.; Cirkovic, S. T.

    2007-01-01

    The quality of a beam in a cyclotron depends a lot on the choice of initial conditions for acceleration. The criteria defining optimal acceleration as well as the choice of the corresponding initial conditions have been outlined. The results of beam dynamics simulations with optimal and non-optimal initial conditions are compared. (author)

  20. Initial orthostatic hypotension: review of a forgotten condition

    NARCIS (Netherlands)

    Wieling, Wouter; Krediet, C. T. Paul; van Dijk, Nynke; Linzer, Mark; Tschakovsky, Michael E.

    2007-01-01

    Several studies have shown that standing up is a frequent (3-10 %) trigger of loss of consciousness both in young and old subjects. An exaggerated transient BP (blood pressure) fall upon standing is the underlying cause. IOH (initial orthostatic hypotension) is defined as a transient BP decrease

  1. Probing the cosmological initial conditions using the CMB

    Science.gov (United States)

    Yadav, Amit P. S.

    In the last few decades, advances in observational cosmology have given us a standard model of cosmology. The basic cosmological parameters have been laid out to high precision. Cosmologists have started asking questions about the nature of the cosmological initial conditions. Many ambitious experiments such as Planck satellite, EBEX, ACT, CAPMAP, QUaD, BICEP, SPIDER, QUIET, and GEM are underway. Experiments like these will provide us with a wealth of information about CMB polarization, CMB lensing, and polarization foregrounds. These experiments will be complemented with great observational campaigns to map the 3D structure in the Universe and new particle physics constraints from the Large Hadron Collider. In my graduate work I have made explicit how observations of the CMB temperature and E-polarization anisotropies can be combined to provide optimal constraints on models of the early universe at the highest energies. I have developed new ways of constraining models of the early universe using CMB temperature and polarization data. Inflation is one of the most promising theories of the early universe. Different inflationary models predict different amounts of non-Gaussian perturbations. Although any non-Gaussianity predicted by the canonical inflation model is very small, there exist models which can generate significant amounts of non-Gaussianities. Hence any characterization of non-Gaussianity of the primordial perturbations constrains the models of inflation. The information in the bispectrum (or higher order moments) is completely independent of the power spectrum constraints on the amplitude of primordial power spectrum (A), the scalar spectral index of the primordial power spectrum ns, and the running of the primordial power spectrum. My work has made it possible to extract the bispectrum information from large, high resolution CMB temperature and polarization data. We have demonstrated that the primordial adiabatic perturbations can be reconstructed using

  2. Influence of the initial state of carbon nanotubes on their colloidal stability under natural conditions

    International Nuclear Information System (INIS)

    Schwyzer, Irene; Kaegi, Ralf; Sigg, Laura; Magrez, Arnaud; Nowack, Bernd

    2011-01-01

    The colloidal stability of dry and suspended carbon nanotubes (CNTs) in the presence of amphiphilic compounds (i.e. natural organic matter or surfactants) at environmentally realistic concentrations was investigated over several days. The suspensions were analyzed for CNT concentration (UV-vis spectroscopy), particle size (nanoparticle tracking analysis), and CNT length and dispersion quality (TEM). When added in dry form, around 1% of the added CNTs remained suspended. Pre-dispersion in organic solvent or anionic detergent stabilized up to 65% of the added CNTs after 20 days of mild shaking and 5 days of settling. The initial state of the CNTs (dry vs. suspended) and the medium composition hence are critical determinants for the partitioning of CNTs between sediment and the water column. TEM analysis revealed that single suspended CNTs were present in all suspensions and that shaking and settling resulted in a fractionation of the CNTs with shorter CNTs remaining predominantly in suspension. - Highlights: → Individually suspended CNTs are present under environment relevant conditions. → The number of suspended CNTs varies depending on the medium composition. → Surfactants at environmental concentrations have no suspending effect on dry CNTs. → Pre-dispersed CNTs are more stable in suspension than dry CNTs. - The colloidal stability of CNTs varies a lot depending on the initial state of the CNTs (dry vs. pre-dispersed), the applied dispersant for pre-suspension, and the composition of the medium.

  3. Mixing-model Sensitivity to Initial Conditions in Hydrodynamic Predictions

    Science.gov (United States)

    Bigelow, Josiah; Silva, Humberto; Truman, C. Randall; Vorobieff, Peter

    2017-11-01

    Amagat and Dalton mixing-models were studied to compare their thermodynamic prediction of shock states. Numerical simulations with the Sandia National Laboratories shock hydrodynamic code CTH modeled University of New Mexico (UNM) shock tube laboratory experiments shocking a 1:1 molar mixture of helium (He) and sulfur hexafluoride (SF6) . Five input parameters were varied for sensitivity analysis: driver section pressure, driver section density, test section pressure, test section density, and mixture ratio (mole fraction). We show via incremental Latin hypercube sampling (LHS) analysis that significant differences exist between Amagat and Dalton mixing-model predictions. The differences observed in predicted shock speeds, temperatures, and pressures grow more pronounced with higher shock speeds. Supported by NNSA Grant DE-0002913.

  4. Varying the agglomeration position of particles in a micro-channel using Acoustic Radiation Force beyond the resonance condition.

    Science.gov (United States)

    Dron, Olivier; Aider, Jean-Luc

    2013-09-01

    It is well-known that particles can be focused at mid-height of a micro-channel using Acoustic Radiation Force (ARF) tuned at the resonance frequency (h=λ/2). The resonance condition is a strong limitation to the use of acoustophoresis (particles manipulation using acoustic force) in many applications. In this study we show that it is possible to focus the particles anywhere along the height of a micro-channel just by varying the acoustic frequency, in contradiction with the resonance condition. This result has been thoroughly checked experimentally. The different physical properties as well as wall materials have been changed. The wall materials is finally the only critical parameters. One of the specificity of the micro-channel is the thickness of the carrier and reflector layer. A preliminary analysis of the experimental results suggests that the acoustic focusing beyond the classic resonance condition can be explained in the framework of the multilayered resonator proposed by Hill [1]. Nevertheless, further numerical studies are needed in order to confirm and fully understand how the acoustic pressure node can be moved over the entire height of the micro channel by varying the acoustic frequency. Despite some uncertainties about the origin of the phenomenon, it is robust and can be used for improved acoustic sorting or manipulation of particles or biological cells in confined set-ups. Copyright © 2013 Elsevier B.V. All rights reserved.

  5. Recovery methods of the dragonfly from irregular initial conditions

    Science.gov (United States)

    Melfi, James; Leonardo, Anthony; Wang, Jane

    We release dragonflies from a magnetic tether in a wide range of initial orientations, which results in them utilizing multiple methods to regain their typical flight orientation. Special focus is placed on dropping them while upside down, as the recovery method used is a purely rolling motion. Filming this stereotypical motion with a trio of high speed cameras at 4000 fps, we capture detailed body and wing kinematics data to determine how the dragonfly generates this motion. By replaying the flights within a computer simulation, we can isolate the significant changes to wing kinematics, and find that it is an asymmetry in the wing pitch which generates the roll. Further investigation demonstrates that this choice is highly dependent upon the state of the dragonfly, and as such our results indicate the dragonfly both tracks its current state, and changes its mid-flight control mechanisms accordingly.

  6. Identifying Initial Condition in Degenerate Parabolic Equation with Singular Potential

    Directory of Open Access Journals (Sweden)

    K. Atifi

    2017-01-01

    Full Text Available A hybrid algorithm and regularization method are proposed, for the first time, to solve the one-dimensional degenerate inverse heat conduction problem to estimate the initial temperature distribution from point measurements. The evolution of the heat is given by a degenerate parabolic equation with singular potential. This problem can be formulated in a least-squares framework, an iterative procedure which minimizes the difference between the given measurements and the value at sensor locations of a reconstructed field. The mathematical model leads to a nonconvex minimization problem. To solve it, we prove the existence of at least one solution of problem and we propose two approaches: the first is based on a Tikhonov regularization, while the second approach is based on a hybrid genetic algorithm (married genetic with descent method type gradient. Some numerical experiments are given.

  7. Urban tree species show the same hydraulic response to vapor pressure deficit across varying tree size and environmental conditions.

    Directory of Open Access Journals (Sweden)

    Lixin Chen

    Full Text Available The functional convergence of tree transpiration has rarely been tested for tree species growing under urban conditions even though it is of significance to elucidate the relationship between functional convergence and species differences of urban trees for establishing sustainable urban forests in the context of forest water relations.We measured sap flux of four urban tree species including Cedrus deodara, Zelkova schneideriana, Euonymus bungeanus and Metasequoia glyptostroboides in an urban park by using thermal dissipation probes (TDP. The concurrent microclimate conditions and soil moisture content were also measured. Our objectives were to examine 1 the influence of tree species and size on transpiration, and 2 the hydraulic control of urban trees under different environmental conditions over the transpiration in response to VPD as represented by canopy conductance. The results showed that the functional convergence between tree diameter at breast height (DBH and tree canopy transpiration amount (E(c was not reliable to predict stand transpiration and there were species differences within same DBH class. Species differed in transpiration patterns to seasonal weather progression and soil water stress as a result of varied sensitivity to water availability. Species differences were also found in their potential maximum transpiration rate and reaction to light. However, a same theoretical hydraulic relationship between G(c at VPD = 1 kPa (G(cref and the G(c sensitivity to VPD (-dG(c/dlnVPD across studied species as well as under contrasting soil water and R(s conditions in the urban area.We concluded that urban trees show the same hydraulic regulation over response to VPD across varying tree size and environmental conditions and thus tree transpiration could be predicted with appropriate assessment of G(cref.

  8. Urban tree species show the same hydraulic response to vapor pressure deficit across varying tree size and environmental conditions.

    Science.gov (United States)

    Chen, Lixin; Zhang, Zhiqiang; Ewers, Brent E

    2012-01-01

    The functional convergence of tree transpiration has rarely been tested for tree species growing under urban conditions even though it is of significance to elucidate the relationship between functional convergence and species differences of urban trees for establishing sustainable urban forests in the context of forest water relations. We measured sap flux of four urban tree species including Cedrus deodara, Zelkova schneideriana, Euonymus bungeanus and Metasequoia glyptostroboides in an urban park by using thermal dissipation probes (TDP). The concurrent microclimate conditions and soil moisture content were also measured. Our objectives were to examine 1) the influence of tree species and size on transpiration, and 2) the hydraulic control of urban trees under different environmental conditions over the transpiration in response to VPD as represented by canopy conductance. The results showed that the functional convergence between tree diameter at breast height (DBH) and tree canopy transpiration amount (E(c)) was not reliable to predict stand transpiration and there were species differences within same DBH class. Species differed in transpiration patterns to seasonal weather progression and soil water stress as a result of varied sensitivity to water availability. Species differences were also found in their potential maximum transpiration rate and reaction to light. However, a same theoretical hydraulic relationship between G(c) at VPD = 1 kPa (G(cref)) and the G(c) sensitivity to VPD (-dG(c)/dlnVPD) across studied species as well as under contrasting soil water and R(s) conditions in the urban area. We concluded that urban trees show the same hydraulic regulation over response to VPD across varying tree size and environmental conditions and thus tree transpiration could be predicted with appropriate assessment of G(cref).

  9. Soil erosion and effluent particle size distribution under different initial conditions and rock fragment coverage

    Science.gov (United States)

    Jomaa, S.; Barry, D. A.; Brovelli, A.; Heng, B. C. P.; Sander, G. C.; Parlange, J.-Y.

    2012-04-01

    It is well known that the presence of rock fragments on the soil surface and the soil's initial characteristics (moisture content, surface roughness, bulk density, etc.) are key factors influencing soil erosion dynamics and sediment delivery. In addition, the interaction of these factors increases the complexity of soil erosion patterns and makes predictions more difficult. The aim of this study was (i) to investigate the effect of soil initial conditions and rock fragment coverage on soil erosion yields and effluent particle size distribution and (ii) to evaluate to what extent the rock fragment coverage controls this relationship. Three laboratory flume experiments with constant precipitation rate of 74 mm/h on a loamy soil parcel with a 2% slope were performed. Experiments with duration of 2 h were conducted using the 6-m × 2-m EPFL erosion flume. During each experiment two conditions were considered, a bare soil and a rock fragment-protected (with 40% coverage) soil. The initial soil surface state was varied between the three experiments, from a freshly re-ploughed and almost dry condition to a compacted soil with a well-developed shield layer and high moisture content. Experiments were designed so that rain splash was the primary driver of soil erosion. Results showed that the amount of eroded mass was highly controlled by the initial soil conditions and whether the steady-state equilibrium was un-, partially- or fully- developed during the previous event. Additionally, results revealed that sediment yields and particle size composition in the initial part of an erosion event are more sensitive to the erosion history than the long-time behaviour. This latter appears to be mainly controlled by rainfall intensity. If steady-state was achieved for a previous event, then the next event consistently produced concentrations for each size class that peaked rapidly, and then declined gradually to steady-state equilibrium. If steady state was not obtained, then

  10. Comparison of creep behavior under varying load/temperature conditions between Hastelloy XR alloys with different boron content levels

    International Nuclear Information System (INIS)

    Tsuji, Hirokazu; Nakajima, Hajime; Shindo, Masami; Tanabe, Tatsuhiko; Nakasone, Yuji.

    1996-01-01

    In the design of the high-temperature components, it is often required to predict the creep rupture life under the conditions in which the stress and/or temperature may vary by using the data obtained with the constant load and temperature creep rupture tests. Some conventional creep damage rules have been proposed to meet the above-mentioned requirement. Currently only limited data are available on the behavior of Hastelloy XR, which is a developed alloy as the structural material for high-temperature components of the High-Temperature Engineering Test Reactor (HTTR), under varying stress and/or temperature creep conditions. Hence a series of constant load and temperature creep rupture tests as well as varying load and temperature creep rupture tests was carried out on two kinds of Hastelloy XR alloys whose boron content levels are different, i.e., below 10 and 60 mass ppm. The life fraction rule completely fails in the prediction of the creep rupture life of Hastelloy XR with 60 mass ppm boron under varying load and temperature conditions though the rule shows good applicability for Hastelloy XR with below 10 mass ppm boron. The change of boron content level of the material during the tests is the most probable source of impairing the applicability of the life fraction rule to Hastelloy XR whose boron content level is 60 mass ppm. The modified life fraction rule has been proposed based on the dependence of the creep rupture strength on the boron content level of the alloy. The modified rule successfully predicts the creep rupture life under the two stage creep test conditions from 1000 to 900degC. The trend observed in the two stage creep tests from 900 to 1000degC can be qualitatively explained by the mechanism that the oxide film which is formed during the prior exposure to 900degC plays the role of the protective barrier against the boron dissipation into the environment. (J.P.N.)

  11. Synthesis of different-sized silver nanoparticles by simply varying reaction conditions with leaf extracts of Bauhinia variegata L.

    Science.gov (United States)

    Kumar, V; Yadav, S K

    2012-03-01

    Green synthesis of nanoparticles is one of the crucial requirements in today's climate change scenario all over the world. In view of this, leaf extract (LE) of Bauhinia variegata L. possessing strong antidiabetic and antibacterial properties has been used to synthesise silver nanoparticles (SNP) in a controlled manner. Various-sized SNP (20-120 nm) were synthesised by varying incubation temperature, silver nitrate and LE concentrations. The rate of SNP synthesis and their size increased with increase in AgNO(3) concentration up to 4 mM. With increase in LE concentration, size and aggregation of SNP was increased. The size and aggregation of SNP were also increased at temperatures above and below 40°C. This has suggested that size and dispersion of SNP can be controlled by varying reaction components and conditions. Polarity-based fractionation of B. variegata LE has suggested that only water-soluble fraction is responsible for SNP synthesis. Fourier transform infrared spectroscopy analysis revealed the attachment of polyphenolic and carbohydrate moieties to SNP. The synthesised SNPs were found stable in double distilled water, BSA and phosphate buffer (pH 7.4). On the contrary, incubation of SNP with NaCl induced aggregation. This suggests the safe use of SNP for various in vivo applications.

  12. Influence of changes in initial conditions for the simulation of dynamic systems

    Energy Technology Data Exchange (ETDEWEB)

    Kotyrba, Martin [Department of Informatics and Computers, University of Ostrava, 30 dubna 22, Ostrava (Czech Republic)

    2015-03-10

    Chaos theory is a field of study in mathematics, with applications in several disciplines including meteorology, sociology, physics, engineering, economics, biology, and philosophy. Chaos theory studies the behavior of dynamical systems that are highly sensitive to initial conditions—a paradigm popularly referred to as the butterfly effect. Small differences in initial conditions field widely diverging outcomes for such dynamical systems, rendering long-term prediction impossible in general. This happens even though these systems are deterministic, meaning that their future behavior is fully determined by their initial conditions, with no random elements involved. In this paperinfluence of changes in initial conditions will be presented for the simulation of Lorenz system.

  13. Varying hydric conditions during incubation influence egg water exchange and hatchling phenotype in the red-eared slider turtle.

    Science.gov (United States)

    Delmas, Virginie; Bonnet, Xavier; Girondot, Marc; Prévot-Julliard, Anne-Caroline

    2008-01-01

    Environmental conditions within the nest, notably temperature and moisture of substrate, exert a powerful influence during embryogenesis in oviparous reptiles. The influence of fluctuating nest temperatures has been experimentally examined in different reptile species; however, similar experiments using moisture as the key variable are lacking. In this article, we examine the effect of various substrate moisture regimes during incubation on different traits (egg mass, incubation length, and hatchling mass) in a chelonian species with flexible-shelled eggs, the red-eared slider turtle (Trachemys scripta elegans). Our results show that the rate of water uptake by the eggs was higher in wet than in dry substrate and varied across development. More important, during the first third of development, the egg mass changes were relatively independent of the soil moisture level; they became very sensitive to moisture levels during the other two-thirds. Moreover, hydric conditions exerted a strong influence on the eggs' long-term sensitivity to the moisture of the substrate. Even short-term episodes of high or low levels of moisture modified permanently their water sensitivity, notably through modification of eggshell shape and volume, and in turn entailed significant effects on hatchling mass (and hence offspring quality). Such complex influences of fluctuating moisture levels at various incubation stages on hatchling phenotype better reflect the natural situation, compared to experiments based on stable, albeit different, moisture levels.

  14. Experiments and numerical modeling of fast flowing liquid metal thin films under spatially varying magnetic field conditions

    Science.gov (United States)

    Narula, Manmeet Singh

    Innovative concepts using fast flowing thin films of liquid metals (like lithium) have been proposed for the protection of the divertor surface in magnetic fusion devices. However, concerns exist about the possibility of establishing the required flow of liquid metal thin films because of the presence of strong magnetic fields which can cause flow disrupting MHD effects. A plan is underway to design liquid lithium based divertor protection concepts for NSTX, a small spherical torus experiment at Princeton. Of these, a promising concept is the use of modularized fast flowing liquid lithium film zones, as the divertor (called the NSTX liquid surface module concept or NSTX LSM). The dynamic response of the liquid metal film flow in a spatially varying magnetic field configuration is still unknown and it is suspected that some unpredicted effects might be lurking. The primary goal of the research work being reported in this dissertation is to provide qualitative and quantitative information on the liquid metal film flow dynamics under spatially varying magnetic field conditions, typical of the divertor region of a magnetic fusion device. The liquid metal film flow dynamics have been studied through a synergic experimental and numerical modeling effort. The Magneto Thermofluid Omnibus Research (MTOR) facility at UCLA has been used to design several experiments to study the MHD interaction of liquid gallium films under a scaled NSTX outboard divertor magnetic field environment. A 3D multi-material, free surface MHD modeling capability is under development in collaboration with HyPerComp Inc., an SBIR vendor. This numerical code called HIMAG provides a unique capability to model the equations of incompressible MHD with a free surface. Some parts of this modeling capability have been developed in this research work, in the form of subroutines for HIMAG. Extensive code debugging and benchmarking exercise has also been carried out. Finally, HIMAG has been used to study the

  15. Impact of Varying Wave Conditions on the Mobility of Arsenic in a Nearshore Aquifer on the Great Lakes

    Science.gov (United States)

    Rakhimbekova, S.; O'Carroll, D. M.; Robinson, C. E.

    2017-12-01

    Groundwater-coastal water interactions play an important role in controlling the behavior of inorganic chemicals in nearshore aquifers and the subsequent flux of these chemicals to receiving coastal waters. Previous studies have shown that dynamic groundwater flows and water exchange across the sediment-water interface can set up strong geochemical gradients and an important reaction zone in a nearshore aquifer that affect the fate of reactive chemicals. There is limited understanding of the impact of transient coastal forcing such as wave conditions on groundwater dynamics and geochemistry in a nearshore aquifer. The goal of this study was to assess the impact of intensified wave conditions on the behavior of arsenic in a nearshore aquifer and to determine the hydrological and geochemical factors controlling its fate and ultimate delivery to receiving coastal waters. Field investigations were conducted over the period of intensified wave conditions on a freshwater beach on Lake Erie, Canada. High spatial resolution aqueous and sediment sampling was conducted to characterize the subsurface distribution of inorganic species in the nearshore aquifer. Numerical groundwater flow and transport simulations were conducted to evaluate wave-induced perturbations in the flow dynamics including characterizing changes in the groundwater flow recirculations in the nearshore aquifer. The combination of field data and numerical simulations reveal that varying wave conditions alter groundwater flows and set up geochemical transition zones within the aquifer resulting in the release and sequestration of arsenic. Interactions between oxic surface water, mildly reducing shallow groundwater, and reducing sulfur- and iron-rich deep groundwater promote dynamic iron, sulfur and manganese cycling which control the mobility of arsenic in the aquifer. The findings of this study have potential implications for the fate and transport of other reactive chemicals (e.g. phosphorus, mercury) in

  16. The effect of coronae on leader initiation and development under thunderstorm conditions and in long air gaps

    International Nuclear Information System (INIS)

    Aleksandrov, N.L.; Bazelyan, E.M.; Carpenter Jr, R.B.; Drabkin, M.M.; Raizer, Yu P.

    2001-01-01

    The initiation and development of a leader is theoretically studied by considering an electrode which is embedded in a cloud of space charge injected by a corona discharge. The focus is on the initiation of upward lightning from a stationary grounded object in a thundercloud electric field. The main results are also applicable to the leader process in long laboratory air gaps at direct voltage. Simple physical models of non-stationary coronae developing in free space near a solitary stressed sphere and of a leader propagating in the space charge cloud of coronae are suggested. It is shown that the electric field redistribution due to the space charge released by the long corona discharge near the top of a high object hinders the initiation and development of an upward leader from the object in a thundercloud electric field. The conditions for the formation of corona streamers that are required to initiate a leader are derived. The criteria are obtained for a leader to be initiated and propagate in the space charge cloud. A hypothesis is proposed that the streamers are never initiated near the top of a high object under thunderstorm conditions if at ground level there is only a slowly-varying electric field of the thundercloud. The streamers may be induced by the fast-rising electric field of distant downward leaders or intracloud discharges. (author)

  17. Evaluation of the Survivability of Microorganisms Deposited on Filtering Respiratory Protective Devices under Varying Conditions of Humidity

    Directory of Open Access Journals (Sweden)

    Katarzyna Majchrzycka

    2016-01-01

    Full Text Available Bioaerosols are common biological factors in work environments, which require routine use of filtering respiratory protective devices (FRPDs. Currently, no studies link humidity changes in the filter materials of such devices, during use, with microorganism survivability. Our aim was to determine the microclimate inside FRPDs, by simulating breathing, and to evaluate microorganism survivability under varying humidity conditions. Breathing was simulated using commercial filtering facepiece respirators in a model system. Polypropylene melt-blown nonwoven fabrics with moisture contents of 40%, 80%, and 200%, were used for assessment of microorganisms survivability. A modified AATCC 100-2004 method was used to measure the survivability of ATCC and NCAIM microorganisms: Escherichia coli, Staphylococcus aureus, Bacillus subtilis, Candida albicans and Aspergillus niger. During simulation relative humidity under the facepiece increased after 7 min of usage to 84%–92% and temperature increased to 29–30 °C. S. aureus survived the best on filter materials with 40%–200% moisture content. A decrease in survivability was observed for E. coli and C. albicans when mass humidity decreased. We found that B. subtilis and A. niger proliferated for 48–72 h of incubation and then died regardless of the moisture content. In conclusion, our tests showed that the survivability of microorganisms on filter materials depends on the amount of accumulated moisture and microorganism type.

  18. Evaluation of the Survivability of Microorganisms Deposited on Filtering Respiratory Protective Devices under Varying Conditions of Humidity.

    Science.gov (United States)

    Majchrzycka, Katarzyna; Okrasa, Małgorzata; Skóra, Justyna; Gutarowska, Beata

    2016-01-04

    Bioaerosols are common biological factors in work environments, which require routine use of filtering respiratory protective devices (FRPDs). Currently, no studies link humidity changes in the filter materials of such devices, during use, with microorganism survivability. Our aim was to determine the microclimate inside FRPDs, by simulating breathing, and to evaluate microorganism survivability under varying humidity conditions. Breathing was simulated using commercial filtering facepiece respirators in a model system. Polypropylene melt-blown nonwoven fabrics with moisture contents of 40%, 80%, and 200%, were used for assessment of microorganisms survivability. A modified AATCC 100-2004 method was used to measure the survivability of ATCC and NCAIM microorganisms: Escherichia coli, Staphylococcus aureus, Bacillus subtilis, Candida albicans and Aspergillus niger. During simulation relative humidity under the facepiece increased after 7 min of usage to 84%-92% and temperature increased to 29-30 °C. S. aureus survived the best on filter materials with 40%-200% moisture content. A decrease in survivability was observed for E. coli and C. albicans when mass humidity decreased. We found that B. subtilis and A. niger proliferated for 48-72 h of incubation and then died regardless of the moisture content. In conclusion, our tests showed that the survivability of microorganisms on filter materials depends on the amount of accumulated moisture and microorganism type.

  19. Relationship between continuity of care and adverse outcomes varies by number of chronic conditions among older adults with diabetes

    Directory of Open Access Journals (Sweden)

    Eva H. DuGoff

    2016-06-01

    Full Text Available Follow us on Twitter Co-Editors-in-Chief Martin Fortin Jane Gunn Stewart W. Mercer Susan Smith Marjan van den Akker Society for Academic Primary Care Journal Help USER You are logged in as... avalster My Profile Log Out JOURNAL CONTENT Search Search Scope Search Browse By Issue By Author By Title By Sections By Identify Types OPEN JOURNAL SYSTEMS FONT SIZE Make font size smallerMake font size defaultMake font size larger INFORMATION For Readers For Authors For Librarians ARTICLE TOOLS Print this article Indexing metadata How to cite item Supplementary files Finding References Email this article Email the author Post a Comment NOTIFICATIONS View (378 new Manage IRCMO NEWS ‘Addressing the global challenge of... Publications on multimorbidity... The CARE Plus study Prevalence of multimorbidity in the... Multimorbidity in adults from a... CURRENT ISSUE Atom logo RSS2 logo RSS1 logo HOSTED BY Part of the PKP Publishing Services Network HOME ABOUT USER HOME SEARCH CURRENT ARCHIVES ANNOUNCEMENTS PUBLISHER AUTHOR GUIDELINES SUBMISSIONS WHY PUBLISH WITH US? Home > Vol 6, No 2 (2016 >\tDuGoff Relationship between continuity of care and adverse outcomes varies by number of chronic conditions among older adults with diabetes Eva H. DuGoff, Karen Bandeen-Roche, Gerard F. Anderson Abstract Background: Continuity of care is a basic tenant of primary care practice. However, the evidence on the importance of continuity of care for older adults with complex conditions is mixed. Objective: To assess the relationship between measurement of continuity of care, number of chronic conditions, and health outcomes. Design: We analyzed data from a cohort of 1,600 US older adults with diabetes and ≥1 other chronic condition in a private Medicare health plan from July 2010 to December 2011. Multivariate regression models were used to examine the association of baseline continuity (the first 6 months and the composite outcome of any emergency room use or inpatient

  20. Initial condition effects on large scale structure in numerical simulations of plane mixing layers

    Science.gov (United States)

    McMullan, W. A.; Garrett, S. J.

    2016-01-01

    In this paper, Large Eddy Simulations are performed on the spatially developing plane turbulent mixing layer. The simulated mixing layers originate from initially laminar conditions. The focus of this research is on the effect of the nature of the imposed fluctuations on the large-scale spanwise and streamwise structures in the flow. Two simulations are performed; one with low-level three-dimensional inflow fluctuations obtained from pseudo-random numbers, the other with physically correlated fluctuations of the same magnitude obtained from an inflow generation technique. Where white-noise fluctuations provide the inflow disturbances, no spatially stationary streamwise vortex structure is observed, and the large-scale spanwise turbulent vortical structures grow continuously and linearly. These structures are observed to have a three-dimensional internal geometry with branches and dislocations. Where physically correlated provide the inflow disturbances a "streaky" streamwise structure that is spatially stationary is observed, with the large-scale turbulent vortical structures growing with the square-root of time. These large-scale structures are quasi-two-dimensional, on top of which the secondary structure rides. The simulation results are discussed in the context of the varying interpretations of mixing layer growth that have been postulated. Recommendations are made concerning the data required from experiments in order to produce accurate numerical simulation recreations of real flows.

  1. Determination of Initial Conditions for the Safety Analysis by Random Sampling of Operating Parameters

    International Nuclear Information System (INIS)

    Jeong, Hae-Yong; Park, Moon-Ghu

    2015-01-01

    In most existing evaluation methodologies, which follow a conservative approach, the most conservative initial conditions are searched for each transient scenario through tremendous assessment for wide operating windows or limiting conditions for operation (LCO) allowed by the operating guidelines. In this procedure, a user effect could be involved and a remarkable time and human resources are consumed. In the present study, we investigated a more effective statistical method for the selection of the most conservative initial condition by the use of random sampling of operating parameters affecting the initial conditions. A method for the determination of initial conditions based on random sampling of plant design parameters is proposed. This method is expected to be applied for the selection of the most conservative initial plant conditions in the safety analysis using a conservative evaluation methodology. In the method, it is suggested that the initial conditions of reactor coolant flow rate, pressurizer level, pressurizer pressure, and SG level are adjusted by controlling the pump rated flow, setpoints of PLCS, PPCS, and FWCS, respectively. The proposed technique is expected to contribute to eliminate the human factors introduced in the conventional safety analysis procedure and also to reduce the human resources invested in the safety evaluation of nuclear power plants

  2. Heavy metals in precipitation waters under conditions of varied anthropopressure in typical of European low mountain regions

    Directory of Open Access Journals (Sweden)

    Rabajczyk A.

    2013-04-01

    Full Text Available The environment is a dynamic system, subject to change resulting from a variety of physicochemical factors, such as temperature, pressure, pH, redox potential and human activity. The quantity and variety of these determinants cause the inflow of substances into individual environmental elements to vary in both time and space, as well as in terms of substance types and quantities. The energy and matter flow in the environment determines its integrity, which means that the processes occurring in one element of the environment affect the others. A certain measure of the energy and matter flow is the migration of chemical substances in various forms from one place to another. In a particular geographical space, under natural conditions, a specific level of balance between individual processes appears; in areas subject to anthropopressure, the correlations are different. In small areas, varying deposition volumes and chemism of precipitation waters which reach the substratum directly can both be observed. The study area is similar in terms of geological origins as well as morphological, structural and physico-chemical properties, and is typical of European low mountain regions. A qualitative and quantitative study of wet atmospheric precipitation was conducted between February 2009 and May 2011 in the Bobrza river catchment in the Holy Cross (Świętokrzyskie Mountains (Poland, at three sampling sites of varying land development and distance from sources of various acidic-alkaline emissions. Field and laboratory work was conducted over 29 months, from February 2009 to May 2011. Atmospheric precipitation measurements were carried out in a continuous manner by means of a Hellman rain gauge (200cm2. The collecting surface was placed at ground level (0m AGL. The application of a collecting funnel and an adequately prepared polyethylene collecting can in the rain gauge enabled the measurement of precipitation volume and water sampling for chemical

  3. On the formation of sulphuric acid – amine clusters in varying atmospheric conditions and its influence on atmospheric new particle formation

    Directory of Open Access Journals (Sweden)

    I. K. Ortega

    2012-10-01

    Full Text Available Sulphuric acid is a key component in atmospheric new particle formation. However, sulphuric acid alone does not form stable enough clusters to initiate particle formation in atmospheric conditions. Strong bases, such as amines, have been suggested to stabilize sulphuric acid clusters and thus participate in particle formation. We modelled the formation rate of clusters with two sulphuric acid and two amine molecules (JA2B2 at varying atmospherically relevant conditions with respect to concentrations of sulphuric acid ([H2SO4], dimethylamine ([DMA] and trimethylamine ([TMA], temperature and relative humidity (RH. We also tested how the model results change if we assume that the clusters with two sulphuric acid and two amine molecules would act as seeds for heterogeneous nucleation of organic vapours (other than amines with higher atmospheric concentrations than sulphuric acid. The modelled formation rates JA2B2 were functions of sulphuric acid concentration with close to quadratic dependence, which is in good agreement with atmospheric observations of the connection between the particle formation rate and sulphuric acid concentration. The coefficients KA2B2 connecting the cluster formation rate and sulphuric acid concentrations as JA2B2=KA2B2[H2SO4]2 turned out to depend also on amine concentrations, temperature and relative humidity. We compared the modelled coefficients KA2B2 with the corresponding coefficients calculated from the atmospheric observations (Kobs from environments with varying temperatures and levels of anthropogenic influence. By taking into account the modelled behaviour of JA2B2 as a function of [H2SO4], temperature and RH, the atmospheric particle formation rate was reproduced more closely than with the traditional semi-empirical formulae based on sulphuric acid concentration only. The formation rates of clusters with two sulphuric acid and two amine molecules with different amine compositions (DMA or TMA or one of both had

  4. On the initial condition problem of the time domain PMCHWT surface integral equation

    KAUST Repository

    Uysal, Ismail Enes; Bagci, Hakan; Ergin, A. Arif; Ulku, H. Arda

    2017-01-01

    Non-physical, linearly increasing and constant current components are induced in marching on-in-time solution of time domain surface integral equations when initial conditions on time derivatives of (unknown) equivalent currents are not enforced

  5. The Use of Graphs in Specific Situations of the Initial Conditions of Linear Differential Equations

    Science.gov (United States)

    Buendía, Gabriela; Cordero, Francisco

    2013-01-01

    In this article, we present a discussion on the role of graphs and its significance in the relation between the number of initial conditions and the order of a linear differential equation, which is known as the initial value problem. We propose to make a functional framework for the use of graphs that intends to broaden the explanations of the…

  6. Seed banks as a source of vegetation regeneration to support the recovery of degraded rivers: A comparison of river reaches of varying condition.

    Science.gov (United States)

    O'Donnell, Jessica; Fryirs, Kirstie A; Leishman, Michelle R

    2016-01-15

    Anthropogenic disturbance has contributed to widespread geomorphic adjustment and the degradation of many rivers. This research compares for river reaches of varying condition, the potential for seed banks to support geomorphic river recovery through vegetation regeneration. Seven river reaches in the lower Hunter catchment of south-eastern Australia were assessed as being in poor, moderate, or good condition, based on geomorphic and ecological indicators. Seed bank composition within the channel and floodplain (determined in a seedling emergence study) was compared to standing vegetation. Seed bank potential for supporting geomorphic recovery was assessed by measuring native species richness, and the abundance of different plant growth forms, with consideration of the roles played by different growth forms in geomorphic adjustment. The exotic seed bank was considered a limiting factor for achieving ecological restoration goals, and similarly analysed. Seed bank native species richness was comparable between the reaches, and regardless of condition, early successional and pioneer herbs, sedges, grasses and rushes dominated the seed bank. The capacity for these growth forms to colonise and stabilise non-cohesive sediments and initiate biogeomorphic succession, indicates high potential for the seed banks of even highly degraded reaches to contribute to geomorphic river recovery. However, exotic propagules increasingly dominated the seed banks of moderate and poor condition reaches and reflected increasing encroachment by terrestrial exotic vegetation associated with riparian degradation. As the degree of riparian degradation increases, the resources required to control the regeneration of exotic species will similarly increase, if seed bank-based regeneration is to contribute to both geomorphic and ecological restoration goals. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Maximum run-up behavior of tsunamis under non-zero initial velocity condition

    Directory of Open Access Journals (Sweden)

    Baran AYDIN

    2018-03-01

    Full Text Available The tsunami run-up problem is solved non-linearly under the most general initial conditions, that is, for realistic initial waveforms such as N-waves, as well as standard initial waveforms such as solitary waves, in the presence of initial velocity. An initial-boundary value problem governed by the non-linear shallow-water wave equations is solved analytically utilizing the classical separation of variables technique, which proved to be not only fast but also accurate analytical approach for this type of problems. The results provide important information on maximum tsunami run-up qualitatively. We observed that, although the calculated maximum run-ups increase significantly, going as high as double that of the zero-velocity case, initial waves having non-zero fluid velocity exhibit the same run-up behavior as waves without initial velocity, for all wave types considered in this study.

  8. Gravity with free initial conditions: A solution to the cosmological constant problem testable by CMB B -mode polarization

    Science.gov (United States)

    Totani, Tomonori

    2017-10-01

    In standard general relativity the universe cannot be started with arbitrary initial conditions, because four of the ten components of the Einstein's field equations (EFE) are constraints on initial conditions. In the previous work it was proposed to extend the gravity theory to allow free initial conditions, with a motivation to solve the cosmological constant problem. This was done by setting four constraints on metric variations in the action principle, which is reasonable because the gravity's physical degrees of freedom are at most six. However, there are two problems about this theory; the three constraints in addition to the unimodular condition were introduced without clear physical meanings, and the flat Minkowski spacetime is unstable against perturbations. Here a new set of gravitational field equations is derived by replacing the three constraints with new ones requiring that geodesic paths remain geodesic against metric variations. The instability problem is then naturally solved. Implications for the cosmological constant Λ are unchanged; the theory converges into EFE with nonzero Λ by inflation, but Λ varies on scales much larger than the present Hubble horizon. Then galaxies are formed only in small Λ regions, and the cosmological constant problem is solved by the anthropic argument. Because of the increased degrees of freedom in metric dynamics, the theory predicts new non-oscillatory modes of metric anisotropy generated by quantum fluctuation during inflation, and CMB B -mode polarization would be observed differently from the standard predictions by general relativity.

  9. Stellar mass spectrum within massive collapsing clumps. I. Influence of the initial conditions

    Science.gov (United States)

    Lee, Yueh-Ning; Hennebelle, Patrick

    2018-04-01

    Context. Stars constitute the building blocks of our Universe, and their formation is an astrophysical problem of great importance. Aim. We aim to understand the fragmentation of massive molecular star-forming clumps and the effect of initial conditions, namely the density and the level of turbulence, on the resulting distribution of stars. For this purpose, we conduct numerical experiments in which we systematically vary the initial density over four orders of magnitude and the turbulent velocity over a factor ten. In a companion paper, we investigate the dependence of this distribution on the gas thermodynamics. Methods: We performed a series of hydrodynamical numerical simulations using adaptive mesh refinement, with special attention to numerical convergence. We also adapted an existing analytical model to the case of collapsing clouds by employing a density probability distribution function (PDF) ∝ρ-1.5 instead of a lognormal distribution. Results: Simulations and analytical model both show two support regimes, a thermally dominated regime and a turbulence-dominated regime. For the first regime, we infer that dN/d logM ∝ M0, while for the second regime, we obtain dN/d logM ∝ M-3/4. This is valid up to about ten times the mass of the first Larson core, as explained in the companion paper, leading to a peak of the mass spectrum at 0.2 M⊙. From this point, the mass spectrum decreases with decreasing mass except for the most diffuse clouds, where disk fragmentation leads to the formation of objects down to the mass of the first Larson core, that is, to a few 10-2 M⊙. Conclusions: Although the mass spectra we obtain for the most compact clouds qualitatively resemble the observed initial mass function, the distribution exponent is shallower than the expected Salpeter exponent of - 1.35. Nonetheless, we observe a possible transition toward a slightly steeper value that is broadly compatible with the Salpeter exponent for masses above a few solar masses

  10. THE ANALYSIS OF THE COMMODITY PRICE FORECASTING SUCCESS CONSIDERING DIFFERENT LENGTHS OF THE INITIAL CONDITION DRIFT

    Directory of Open Access Journals (Sweden)

    Marcela Lascsáková

    2015-09-01

    Full Text Available In the paper the numerical model based on the exponential approximation of commodity stock exchanges was derived. The price prognoses of aluminium on the London Metal Exchange were determined as numerical solution of the Cauchy initial problem for the 1st order ordinary differential equation. To make the numerical model more accurate the idea of the modification of the initial condition value by the stock exchange was realized. By having analyzed the forecasting success of the chosen initial condition drift types, the initial condition drift providing the most accurate prognoses for the commodity price movements was determined. The suggested modification of the original model made the commodity price prognoses more accurate.

  11. Optimal control of distributed parameter system with incomplete information about the initial condition

    International Nuclear Information System (INIS)

    Kotarski, W.; Kowalewski, A.

    1982-03-01

    In this paper we consider an optimal control problem for a system described by a linear partial differential equation of the parabolic type with Dirichlet's boundary condition. We impose some constraints on the control. The performance functional has the integral form. The control time T is fixed. The initial condition is not given by a known function but belongs to a certain set (incomplete information about the initial state). The problem formulated in this paper describes the process of optimal heating, of which we do not have exact information about the initial temperature on the heated object. We present an example in which the set of admissible controls and one of initial conditions are given by means of the norm constraints too. The application of the well-known projective gradient method in the Hilbert space allows us to obtain the numerical solution for our optimization problem. (author)

  12. Varied Human Tolerance to the Combined Conditions of Low Contrast and Diminished Luminance: A Quasi-Meta Analysis

    Science.gov (United States)

    2017-08-30

    conditions (e.g., dry eyes , mild cataractous conditions, Stevens-Johnson Syndrome ) using CS alone as the performance index. More commonly, it has been...subjects tested under conditions of spherical blur, astigmatic blur, low luminance, and one eye vs. two eyes ...conditions). The vast majority of past mesopic visual performance studies were predominantly isolated to evaluations of various eye disease

  13. Initial conditions and ENSO prediction using a coupled ocean-atmosphere model

    Science.gov (United States)

    Larow, T. E.; Krishnamurti, T. N.

    1998-01-01

    A coupled ocean-atmosphere initialization scheme using Newtonian relaxation has been developed for the Florida State University coupled ocean-atmosphere global general circulation model. The initialization scheme is used to initialize the coupled model for seasonal forecasting the boreal summers of 1987 and 1988. The atmosphere model is a modified version of the Florida State University global spectral model, resolution T-42. The ocean general circulation model consists of a slightly modified version of the Hamburg's climate group model described in Latif (1987) and Latif et al. (1993). The coupling is synchronous with information exchanged every two model hours. Using ECMWF atmospheric daily analysis and observed monthly mean SSTs, two, 1-year, time-dependent, Newtonian relaxation were performed using the coupled model prior to conducting the seasonal forecasts. The coupled initializations were conducted from 1 June 1986 to 1 June 1987 and from 1 June 1987 to 1 June 1988. Newtonian relaxation was applied to the prognostic atmospheric vorticity, divergence, temperature and dew point depression equations. In the ocean model the relaxation was applied to the surface temperature. Two, 10-member ensemble integrations were conducted to examine the impact of the coupled initialization on the seasonal forecasts. The initial conditions used for the ensembles are the ocean's final state after the initialization and the atmospheric initial conditions are ECMWF analysis. Examination of the SST root mean square error and anomaly correlations between observed and forecasted SSTs in the Niño-3 and Niño-4 regions for the 2 seasonal forecasts, show closer agreement between the initialized forecast than two, 10-member non-initialized ensemble forecasts. The main conclusion here is that a single forecast with the coupled initialization outperforms, in SST anomaly prediction, against each of the control forecasts (members of the ensemble) which do not include such an initialization

  14. Consistent initial conditions for the Saint-Venant equations in river network modeling

    Directory of Open Access Journals (Sweden)

    C.-W. Yu

    2017-09-01

    Full Text Available Initial conditions for flows and depths (cross-sectional areas throughout a river network are required for any time-marching (unsteady solution of the one-dimensional (1-D hydrodynamic Saint-Venant equations. For a river network modeled with several Strahler orders of tributaries, comprehensive and consistent synoptic data are typically lacking and synthetic starting conditions are needed. Because of underlying nonlinearity, poorly defined or inconsistent initial conditions can lead to convergence problems and long spin-up times in an unsteady solver. Two new approaches are defined and demonstrated herein for computing flows and cross-sectional areas (or depths. These methods can produce an initial condition data set that is consistent with modeled landscape runoff and river geometry boundary conditions at the initial time. These new methods are (1 the pseudo time-marching method (PTM that iterates toward a steady-state initial condition using an unsteady Saint-Venant solver and (2 the steady-solution method (SSM that makes use of graph theory for initial flow rates and solution of a steady-state 1-D momentum equation for the channel cross-sectional areas. The PTM is shown to be adequate for short river reaches but is significantly slower and has occasional non-convergent behavior for large river networks. The SSM approach is shown to provide a rapid solution of consistent initial conditions for both small and large networks, albeit with the requirement that additional code must be written rather than applying an existing unsteady Saint-Venant solver.

  15. Effect of Initial Hydraulic Conditions on Capillary Rise in a Porous Medium: Pore-Network Modeling

    KAUST Repository

    Joekar-Niasar, V.

    2012-01-01

    The dynamics of capillary rise in a porous medium have been mostly studied in initially dry systems. As initial saturation and initial hydraulic conditions in many natural and industrial porous media can be variable, it is important to investigate the influence of initial conditions on the dynamics of the process. In this study, using dynamic pore-network modeling, we simulated capillary rise in a porous medium for different initial saturations (and consequently initial capillary pressures). Furthermore, the effect of hydraulic connectivity of the wetting phase in corners on the height and velocity of the wetting front was studied. Our simulation results show that there is a trade-off between capillary forces and trapping due to snap-off, which leads to a nonlinear dependence of wetting front velocity on initial saturation at the pore scale. This analysis may provide a possible answer to the experimental observations in the literature showing a non-monotonic dependency between initial saturation and the macroscopic front velocity. © Soil Science Society of America.

  16. Elliptic flow from non-equilibrium initial condition with a saturation scale

    International Nuclear Information System (INIS)

    Ruggieri, M.; Scardina, F.; Plumari, S.; Greco, V.

    2013-01-01

    A current goal of relativistic heavy-ion collisions experiments is the search for a Color Glass Condensate (CGC) as the limiting state of QCD matter at very high density. In viscous hydrodynamics simulations, a standard Glauber initial condition leads to estimate 4πη/s∼1, while employing the Kharzeev–Levin–Nardi (KLN) modeling of the glasma leads to at least a factor of 2 larger η/s. Within a kinetic theory approach based on a relativistic Boltzmann-like transport simulation, our main result is that the out-of-equilibrium initial distribution reduces the efficiency in building-up the elliptic flow. At RHIC energy we find the available data on v 2 are in agreement with a 4πη/s∼1 also for KLN initial conditions. More generally, our study shows that the initial non-equilibrium in p-space can have a significant impact on the build-up of anisotropic flow

  17. The Matter Bispectrum in N-body Simulations with non-Gaussian Initial Conditions

    OpenAIRE

    Sefusatti, Emiliano; Crocce, Martin; Desjacques, Vincent

    2010-01-01

    We present measurements of the dark matter bispectrum in N-body simulations with non-Gaussian initial conditions of the local kind for a large variety of triangular configurations and compare them with predictions from Eulerian perturbation theory up to one-loop corrections. We find that the effects of primordial non-Gaussianity at large scales, when compared to perturbation theory, are well described by the initial component of the matter bispectrum, linearly extrapolated at the redshift of ...

  18. 3-D simulations to investigate initial condition effects on the growth of Rayleigh-Taylor mixing

    Energy Technology Data Exchange (ETDEWEB)

    Andrews, Malcolm J [Los Alamos National Laboratory

    2008-01-01

    The effect of initial conditions on the growth rate of turbulent Rayleigh-Taylor (RT) mixing has been studied using carefully formulated numerical simulations. An integrated large-eddy simulation (ILES) that uses a finite-volume technique was employed to solve the three-dimensional incompressible Euler equations with numerical dissipation. The initial conditions were chosen to test the dependence of the RT growth parameters ({alpha}{sub b}, {alpha}{sub s}) on variations in (a) the spectral bandwidth, (b) the spectral shape, and (c) discrete banded spectra. Our findings support the notion that the overall growth of the RT mixing is strongly dependent on initial conditions. Variation in spectral shapes and bandwidths are found to have a complex effect of the late time development of the RT mixing layer, and raise the question of whether we can design RT transition and turbulence based on our choice of initial conditions. In addition, our results provide a useful database for the initialization and development of closures describing RT transition and turbulence.

  19. Ductile Crack Initiation Criterion with Mismatched Weld Joints Under Dynamic Loading Conditions.

    Science.gov (United States)

    An, Gyubaek; Jeong, Se-Min; Park, Jeongung

    2018-03-01

    Brittle failure of high toughness steel structures tends to occur after ductile crack initiation/propagation. Damages to steel structures were reported in the Hanshin Great Earthquake. Several brittle failures were observed in beam-to-column connection zones with geometrical discontinuity. It is widely known that triaxial stresses accelerate the ductile fracture of steels. The study examined the effects of geometrical heterogeneity and strength mismatches (both of which elevate plastic constraints due to heterogeneous plastic straining) and loading rate on critical conditions initiating ductile fracture. This involved applying the two-parameter criterion (involving equivalent plastic strain and stress triaxiality) to estimate ductile cracking for strength mismatched specimens under static and dynamic tensile loading conditions. Ductile crack initiation testing was conducted under static and dynamic loading conditions using circumferentially notched specimens (Charpy type) with/without strength mismatches. The results indicated that the condition for ductile crack initiation using the two parameter criterion was a transferable criterion to evaluate ductile crack initiation independent of the existence of strength mismatches and loading rates.

  20. Conditional stability in determination of initial data for stochastic parabolic equations

    International Nuclear Information System (INIS)

    Yuan, Ganghua

    2017-01-01

    In this paper, we solve two kinds of inverse problems in determination of the initial data for stochastic parabolic equations. One is determination of the initial data by lateral boundary observation on arbitrary portion of the boundary, the second one is determination of the initial data by internal observation in a subregion inside the domain. We obtain conditional stability for the two kinds of inverse problems. To prove the results, we estimate the initial data by a terminal observation near the initial time, then we estimate this terminal observation by lateral boundary observation on arbitrary portion of the boundary or internal observation in a subregion inside the domain. To achieve those goals, we derive several new Carleman estimates for stochastic parabolic equations in this paper. (paper)

  1. Conditional stability in determination of initial data for stochastic parabolic equations

    Science.gov (United States)

    Yuan, Ganghua

    2017-03-01

    In this paper, we solve two kinds of inverse problems in determination of the initial data for stochastic parabolic equations. One is determination of the initial data by lateral boundary observation on arbitrary portion of the boundary, the second one is determination of the initial data by internal observation in a subregion inside the domain. We obtain conditional stability for the two kinds of inverse problems. To prove the results, we estimate the initial data by a terminal observation near the initial time, then we estimate this terminal observation by lateral boundary observation on arbitrary portion of the boundary or internal observation in a subregion inside the domain. To achieve those goals, we derive several new Carleman estimates for stochastic parabolic equations in this paper.

  2. Corona initiated from grounded objects under thunderstorm conditions and its influence on lightning attachment

    International Nuclear Information System (INIS)

    Bazelyan, E M; Raizer, Yu P; Aleksandrov, N L

    2008-01-01

    Lightning attachment to grounded structures due to the initiation of an upward connecting leader from them is considered taking into account the effect of corona space charge near the structures. It is shown that the corona space charge strongly affects the initiation and development of the connecting leader. Specific features of a non-stationary corona are analysed analytically and numerically for one-dimensional electrode geometries and for a grounded rod coronating in a slowly varying thundercloud electric field that can be enhanced by the charge of an approaching downward lightning leader. Initiation and development of an upward connecting leader or upward lightning from high ground objects are investigated. Prospects of using the effect of coronae to control downward lightning discharges are discussed.

  3. Effect of initial conditions and Mach number on the Richtmyer-Meshkov instability in ICF like conditions

    Science.gov (United States)

    Rao, Pooja; She, Dan; Lim, Hyunkyung; Glimm, James

    2015-11-01

    The qualitative and quantitative effect of initial conditions (linear and non-linear) and high Mach number (1.3 and 1.45) is studied on the turbulent mixing induced by the Richtmyer-Meshkov instability in idealized ICF conditions. The Richtmyer-Meshkov instability seeds Rayleigh-taylor instabilities in ICF experiments and is one of the factors that contributes to reduced performance of ICF experiments. Its also found in collapsing cores of stars and supersonic combustion. We use the Stony Brook University code, FronTier, which is verified via a code comparison study against the AMR multiphysics code FLASH, and validated against vertical shock tube experiments done by the LANL Extreme Fluids Team. These simulations are designed as a step towards simulating more realistic ICF conditions and quantifying the detrimental effects of mixing on the yield.

  4. Predictability of Japan/East Sea (JES) System to Uncertain Initial/Lateral Boundary Conditions and Surface Winds

    National Research Council Canada - National Science Library

    Fang, Chin-Lung

    2003-01-01

    .... Change in either initial or boundary condition leads to a variety of model solutions. It is necessary to specify realistic initial and boundary conditions to achieve better understanding and prediction of the ocean behavior...

  5. On Perturbative Cubic Nonlinear Schrodinger Equations under Complex Nonhomogeneities and Complex Initial Conditions

    Directory of Open Access Journals (Sweden)

    Magdy A. El-Tawil

    2009-01-01

    Full Text Available A perturbing nonlinear Schrodinger equation is studied under general complex nonhomogeneities and complex initial conditions for zero boundary conditions. The perturbation method together with the eigenfunction expansion and variational parameters methods are used to introduce an approximate solution for the perturbative nonlinear case for which a power series solution is proved to exist. Using Mathematica, the symbolic solution algorithm is tested through computing the possible approximations under truncation procedures. The method of solution is illustrated through case studies and figures.

  6. Generation of synthetic surface electromyography signals under fatigue conditions for varying force inputs using feedback control algorithm.

    Science.gov (United States)

    Venugopal, G; Deepak, P; Ghosh, Diptasree M; Ramakrishnan, S

    2017-11-01

    Surface electromyography is a non-invasive technique used for recording the electrical activity of neuromuscular systems. These signals are random, complex and multi-component. There are several techniques to extract information about the force exerted by muscles during any activity. This work attempts to generate surface electromyography signals for various magnitudes of force under isometric non-fatigue and fatigue conditions using a feedback model. The model is based on existing current distribution, volume conductor relations, the feedback control algorithm for rate coding and generation of firing pattern. The result shows that synthetic surface electromyography signals are highly complex in both non-fatigue and fatigue conditions. Furthermore, surface electromyography signals have higher amplitude and lower frequency under fatigue condition. This model can be used to study the influence of various signal parameters under fatigue and non-fatigue conditions.

  7. A SVDD and K-Means Based Early Warning Method for Dual-Rotor Equipment under Time-Varying Operating Conditions

    Directory of Open Access Journals (Sweden)

    Zhinong Jiang

    2018-01-01

    Full Text Available Under frequently time-varying operating conditions, equipment with dual rotors like gas turbines is influenced by two rotors with different rotating speeds. Alarm methods of fixed threshold are unable to consider the influences of time-varying operating conditions. Hence, those methods are not suitable for monitoring dual-rotor equipment. An early warning method for dual-rotor equipment under time-varying operating conditions is proposed in this paper. The influences of time-varying rotating speeds of dual rotors on alarm thresholds have been considered. Firstly, the operating conditions are divided into several limited intervals according to rotating speeds of dual rotors. Secondly, the train data within each interval is processed by SVDD and the allowable ranges (i.e., the alarm threshold of the vibration are determined. The alarm threshold of each interval of operating conditions is obtained. The alarm threshold can be expressed as a sphere, whose controlling parameters are the coordinate of the center and the radius. Then, the cluster center of the test data, whose alarm state is to be judged, can be extracted through K-means. Finally, the alarm state can be obtained by comparing the cluster center with the corresponding sphere. Experiments are conducted to validate the proposed method.

  8. Path dependence, initial conditions, and routines in organizations : The Toyota production system re-examined

    NARCIS (Netherlands)

    Dolfsma, W.A.; van Driel, H.

    2009-01-01

    Purpose - The purpose of this paper is to disentangle and elaborate on the constitutive elements of the concept of path dependence (initial conditions and lock-in) for a concerted and in-depth application to the study of organizational change. Design/methodology/approach - The approach takes the

  9. Influence of the initial conditions for the numerical simulation of two-phase slug flow

    Energy Technology Data Exchange (ETDEWEB)

    Pachas Napa, Alex A.; Morales, Rigoberto E.M.; Medina, Cesar D. Perea

    2010-07-01

    Multiphase flows in pipelines commonly show several patterns depending on the flow rate, geometry and physical properties of the phases. In oil production, the slug flow pattern is the most common among the others. This flow pattern is characterized by an intermittent succession in space and time of an aerated liquid slug and an elongated gas bubble with a liquid film. Slug flow is studied through the slug tracking model described as one-dimensional and Lagrangian frame referenced. In the model, the mass and the momentum balance equations are applied in control volumes constituted by the gas bubble and the liquid slug. Initial conditions must be determined, which need to reproduce the intermittence of the flow pattern. These initial conditions are given by a sequence of flow properties for each unit cell. Properties of the unit cell in initial conditions should reflect the intermittence, for which they can be analyzed in statistical terms. Therefore, statistical distributions should be obtained for the slug flow variables. Distributions are complemented with the mass balance and the bubble design model. The objective of the present work is to obtain initial conditions for the slug tracking model that reproduce a better adjustment of the fluctuating properties for different pipe inclinations (horizontal, vertical or inclined). The numerical results are compared with experimental data obtained by PFG/FEM/UNICAMP for air-water flow at 0 deg, 45 deg and 90 deg and good agreement is observed. (author)

  10. Multiple unit root tests under uncertainty over the initial condition : some powerful modifications

    NARCIS (Netherlands)

    Hanck, C.

    We modify the union-of-rejection unit root test of Harvey et al. "Unit Root Testing in Practice: Dealing with Uncertainty over the Trend and Initial Condition" (Harvey, Econom Theory 25:587-636, 2009). This test rejects if either of two different unit root tests rejects but controls the inherent

  11. Choice of initial conditions in dynamical calculations of distributions of nuclear fission fragments

    International Nuclear Information System (INIS)

    Kosenko, G.I.

    1993-01-01

    The distribution function in the coordinates and momenta for a fissioning system traversing a barrier is determined in terms of Langevin fluctuation-dissipation dynamics. It is shown that this distribution is best described by the Kramers distribution. The equilibrium distribution can be used as the initial condition, provided that the system is in the overdamping regime. 28 refs., 5 figs., 3 tabs

  12. Initial conditions and robust Newton-Raphson for harmonic balance analysis of free-running oscillators

    NARCIS (Netherlands)

    Virtanen, J.E.; Maten, ter E.J.W.; Beelen, T.G.J.; Honkala, M.; Hulkkonen, M.

    2011-01-01

    Poor initial conditions for Harmonic Balance (HB) analysis of freerunning oscillators may lead to divergence of the direct Newton-Raphson method or may prevent to find the solution within an optimization approach. We exploit time integration to obtain estimates for the oscillation frequency and for

  13. Initial conditions and robust Newton-Raphson for harmonic balance analysis of free-running oscillators

    NARCIS (Netherlands)

    Virtanen, J.E.; Maten, ter E.J.W.; Honkala, M.; Hulkkonen, M.; Günther, M.; Bartel, A.; Brunk, M.; Schoeps, S.; Striebel, M.

    2012-01-01

    Poor initial conditions for Harmonic Balance (HB) analysis of free-running oscillators may lead to divergence of the direct Newton-Raphson method or may prevent to find the solution within an optimization approach. We exploit time integration to obtain estimates for the oscillation frequency and for

  14. Computer code calculations of the TMI-2 accident: initial and boundary conditions

    International Nuclear Information System (INIS)

    Behling, S.R.

    1985-05-01

    Initial and boundary conditions during the Three Mile Island Unit 2 (TMI-2) accident are described and detailed. A brief description of the TMI-2 plant configuration is given. Important contributions to the progression of the accident in the reactor coolant system are discussed. Sufficient information is provided to allow calculation of the TMI-2 accident with computer codes

  15. Predicting a contact's sensitivity to initial conditions using metrics of frictional coupling

    International Nuclear Information System (INIS)

    Flicek, Robert C.; Hills, David A.; Brake, Matthew Robert W.

    2016-01-01

    This paper presents a method for predicting how sensitive a frictional contact’s steady-state behavior is to its initial conditions. Previous research has proven that if a contact is uncoupled, i.e. if slip displacements do not influence the contact pressure distribution, then its steady-state response is independent of initial conditions, but if the contact is coupled, the steady-state response depends on initial conditions. In this paper, two metrics for quantifying coupling in discrete frictional systems are examined. These metrics suggest that coupling is dominated by material dissimilarity due to Dundurs’ composite material parameter β when β ≥ 0.2, but geometric mismatch becomes the dominant source of coupling for smaller values of β. Based on a large set of numerical simulations with different contact geometries, material combinations, and friction coefficients, a contact’s sensitivity to initial conditions is found to be correlated with the product of the coupling metric and the friction coefficient. For cyclic shear loading, this correlation is maintained for simulations with different contact geometries, material combinations, and friction coefficients. Furthermore, for cyclic bulk loading, the correlation is only maintained when the contact edge angle is held constant.

  16. On a nonlinear integrodifferential evolution inclusion with nonlocal initial conditions in Banach spaces

    Directory of Open Access Journals (Sweden)

    Zuomao Yan

    2012-01-01

    Full Text Available In this paper, we discuss the existence results for a class of nnlinear integrodifferential evolution inclusions with nonlocal initial conditions in Banach spaces. Our results are based on a fixed point theorem for condensing maps due to Martelli and the resolvent operators combined with approximation techniques.

  17. 42 CFR 433.130 - Waiver of conditions of initial operation and approval.

    Science.gov (United States)

    2010-10-01

    ... Claims Processing and Information Retrieval Systems § 433.130 Waiver of conditions of initial operation... system will not significantly improve the efficiency of the administration of the State plan. (c) If CMS... waiver, that a system would significantly improve the administration of the State Medicaid program, CMS...

  18. Skill of a global seasonal streamflow forecasting system, relative roles of initial conditions and meteorological forcing

    NARCIS (Netherlands)

    Candogan Yossef, N.; Winsemius, H.C.; Weerts, A.; Van Beek, R.; Bierkens, M.F.P.

    2013-01-01

    We investigate the relative contributions of initial conditions (ICs) and meteorological forcing (MF) to the skill of the global seasonal streamflow forecasting system FEWS-World, using the global hydrological model PCRaster Global Water Balance. Potential improvement in forecasting skill through

  19. Model Forecast Skill and Sensitivity to Initial Conditions in the Seasonal Sea Ice Outlook

    Science.gov (United States)

    Blanchard-Wrigglesworth, E.; Cullather, R. I.; Wang, W.; Zhang, J.; Bitz, C. M.

    2015-01-01

    We explore the skill of predictions of September Arctic sea ice extent from dynamical models participating in the Sea Ice Outlook (SIO). Forecasts submitted in August, at roughly 2 month lead times, are skillful. However, skill is lower in forecasts submitted to SIO, which began in 2008, than in hindcasts (retrospective forecasts) of the last few decades. The multimodel mean SIO predictions offer slightly higher skill than the single-model SIO predictions, but neither beats a damped persistence forecast at longer than 2 month lead times. The models are largely unsuccessful at predicting each other, indicating a large difference in model physics and/or initial conditions. Motivated by this, we perform an initial condition sensitivity experiment with four SIO models, applying a fixed -1 m perturbation to the initial sea ice thickness. The significant range of the response among the models suggests that different model physics make a significant contribution to forecast uncertainty.

  20. Perturbations in the initial soil moisture conditions: Impacts on hydrologic simulation in a large river basin

    Science.gov (United States)

    Niroula, Sundar; Halder, Subhadeep; Ghosh, Subimal

    2018-06-01

    Real time hydrologic forecasting requires near accurate initial condition of soil moisture; however, continuous monitoring of soil moisture is not operational in many regions, such as, in Ganga basin, extended in Nepal, India and Bangladesh. Here, we examine the impacts of perturbation/error in the initial soil moisture conditions on simulated soil moisture and streamflow in Ganga basin and its propagation, during the summer monsoon season (June to September). This provides information regarding the required minimum duration of model simulation for attaining the model stability. We use the Variable Infiltration Capacity model for hydrological simulations after validation. Multiple hydrologic simulations are performed, each of 21 days, initialized on every 5th day of the monsoon season for deficit, surplus and normal monsoon years. Each of these simulations is performed with the initial soil moisture condition obtained from long term runs along with positive and negative perturbations. The time required for the convergence of initial errors is obtained for all the cases. We find a quick convergence for the year with high rainfall as well as for the wet spells within a season. We further find high spatial variations in the time required for convergence; the region with high precipitation such as Lower Ganga basin attains convergence at a faster rate. Furthermore, deeper soil layers need more time for convergence. Our analysis is the first attempt on understanding the sensitivity of hydrological simulations of Ganga basin on initial soil moisture conditions. The results obtained here may be useful in understanding the spin-up requirements for operational hydrologic forecasts.

  1. Workshop on initiation of stress corrosion cracking under LWR conditions: Proceedings

    International Nuclear Information System (INIS)

    Nelson, J.L.; Cubicciotti, D.; Licina, G.J.

    1988-05-01

    A workshop titled ''Initiation of Stress Corrosion Cracking under LWR Conditions'' was held in Palo Alto, California on November 13, 1986, hosted by the Electric Power Research Institute. Participants were experts on the topic from nuclear steam supply and component manufacturers, public and private research laboratories, and university environments. Presentations included discussions on the definition of crack initiation, the effects of environmental and electrochemical variables on cracking susceptibility, and detection methods for the determination of crack initiation events and measurement of critical environmental and stress parameters. Examination of the questions related to crack initiation and its relative importance to the overall question of cracking of LWR materials from these perspectives provided inputs to EPRI project managers on the future direction of research efforts designed to prevent and control cracking. Thirteen reports have been cataloged separately

  2. Biodiesel production process optimization and characterization to assess the suitability of the product for varied environmental conditions

    Energy Technology Data Exchange (ETDEWEB)

    Eevera, T.; Rajendran, K.; Saradha, S. [Department of Biotechnology, Periyar Maniammai University, Periyar Nagar, Vallam, Thanjavur, Tamilnadu 613 403 (India)

    2009-03-15

    In this study, both edible (coconut oil, palm oil, groundnut oil, and rice bran oil) and non-edible oils (pongamia, neem and cotton seed oil) were used to optimize the biodiesel production process variables like catalyst concentration, amount of methanol required for reaction, reaction time and reaction temperature. The fuel properties like specific gravity, moisture content, refractive index, acid value, iodine number, saponification value and peroxide value were estimated. Based on the cetane number and iodine value, the methyl esters obtained from palm and coconut oils were not suitable to use as biodiesel in cold weather conditions, but for hot climate condition biodiesel obtained from the remaining oil sources is suitable. (author)

  3. TRANSFORMATION OF PB(II FROM CERRUSITE TO CHLOROPYROMORPHITE IN THE PRESENCE OF HYDROXYAPATITE UNDER VARYING CONDITIONS OF PH

    Science.gov (United States)

    The soluble Pb concentration and formation of chloropyromorphite [Pb5(PO4)3Cl] were monitored during the reaction of cerrusite (PbCO3), a highly bioavailable soil Pb species, and hydroxyapatite [Ca5(PO4)3OH] at various P/Pb molar ratios under constant and dynamic pH conditions. ...

  4. Analytical solution for multi-species contaminant transport in finite media with time-varying boundary conditions

    Science.gov (United States)

    Most analytical solutions available for the equations governing the advective-dispersive transport of multiple solutes undergoing sequential first-order decay reactions have been developed for infinite or semi-infinite spatial domains and steady-state boundary conditions. In this work we present an ...

  5. Foam Core Particleboards with Intumescent FRT Veneer: Cone Calorimeter Testing With Varying Adhesives, Surface Layer Thicknesses, and Processing Conditions

    Science.gov (United States)

    Mark A. Dietenberger; Johannes Welling; Ali Shalbafan

    2014-01-01

    Intumescent FRT Veneers adhered to the surface of foam core particleboard to provide adequate fire protection were evaluated by means of cone calorimeter tests (ASTM E1354). The foam core particleboards were prepared with variations in surface layer treatment, adhesives, surface layer thicknesses, and processing conditions. Ignitability, heat release rate profile, peak...

  6. Cyclic plastic material behavior leading to crack initiation in stainless steel under complex fatigue loading conditions

    International Nuclear Information System (INIS)

    Facheris, G.

    2014-01-01

    The improvement of the reliability and of the safety in the design of components belonging to the primary cooling circuit of a light water nuclear reactor is nowadays one of the most important research topics in nuclear industry. One of the most important damage mechanisms leading the crack initiation in this class of components is the low cycle fatigue (LCF) driven by thermal strain fluctuations caused by the complex thermo-mechanical loading conditions typical for the primary circuit (e.g. operating thermal transients, thermal stratification, turbulent mixing of cold and hot water flows, etc.). The cyclic application of the resulting plastic deformation to the steel grades commonly used for the fabrication of piping parts (e.g. austenitic stainless steels) is associated with a continuous evolution of the mechanical response of the material. As an additional complication, the cyclic behavior of stainless steels is influenced by temperature, strain amplitude and cyclic accumulation of inelastic strain (i.e. ratcheting). The accurate prediction of the structural response of components belonging to the primary cooling circuit requires the development of a reliable constitutive model that must be characterized by a reduced complexity to allow its application in an industrial context. In this framework, the main goal of the current dissertation is to formulate, calibrate and implement in a commercial Finite Element code, a constitutive model that is suitable for the stainless stain grade 316L subjected to complex loading conditions. As a first task, a characterization of the mechanical behavior of 316L subjected to uniaxial and multiaxial strain-controlled conditions (including LCF and ratcheting) is carried out performing several tests in the laboratories of the Paul Scherrer Institute (PSI, Villigen, Switzerland) and of Politecnico di Milano (Italy). The uniaxial experiments demonstrate that, prescribing a strain-controlled ratcheting path, a harder material response

  7. Cyclic plastic material behavior leading to crack initiation in stainless steel under complex fatigue loading conditions

    Energy Technology Data Exchange (ETDEWEB)

    Facheris, G.

    2014-07-01

    The improvement of the reliability and of the safety in the design of components belonging to the primary cooling circuit of a light water nuclear reactor is nowadays one of the most important research topics in nuclear industry. One of the most important damage mechanisms leading the crack initiation in this class of components is the low cycle fatigue (LCF) driven by thermal strain fluctuations caused by the complex thermo-mechanical loading conditions typical for the primary circuit (e.g. operating thermal transients, thermal stratification, turbulent mixing of cold and hot water flows, etc.). The cyclic application of the resulting plastic deformation to the steel grades commonly used for the fabrication of piping parts (e.g. austenitic stainless steels) is associated with a continuous evolution of the mechanical response of the material. As an additional complication, the cyclic behavior of stainless steels is influenced by temperature, strain amplitude and cyclic accumulation of inelastic strain (i.e. ratcheting). The accurate prediction of the structural response of components belonging to the primary cooling circuit requires the development of a reliable constitutive model that must be characterized by a reduced complexity to allow its application in an industrial context. In this framework, the main goal of the current dissertation is to formulate, calibrate and implement in a commercial Finite Element code, a constitutive model that is suitable for the stainless stain grade 316L subjected to complex loading conditions. As a first task, a characterization of the mechanical behavior of 316L subjected to uniaxial and multiaxial strain-controlled conditions (including LCF and ratcheting) is carried out performing several tests in the laboratories of the Paul Scherrer Institute (PSI, Villigen, Switzerland) and of Politecnico di Milano (Italy). The uniaxial experiments demonstrate that, prescribing a strain-controlled ratcheting path, a harder material response

  8. EARLY DYNAMICAL EVOLUTION OF THE SOLAR SYSTEM: PINNING DOWN THE INITIAL CONDITIONS OF THE NICE MODEL

    International Nuclear Information System (INIS)

    Batygin, Konstantin; Brown, Michael E.

    2010-01-01

    In the recent years, the 'Nice' model of solar system formation has attained an unprecedented level of success in reproducing much of the observed orbital architecture of the solar system by evolving the planets to their current locations from a more compact configuration. Within the context of this model, the formation of the classical Kuiper Belt requires a phase during which the ice giants have a high eccentricity. An outstanding question of this model is the initial configuration from which the solar system started out. Recent work has shown that multi-resonant initial conditions can serve as good candidates, as they naturally prevent vigorous type-II migration. In this paper, we use analytical arguments, as well as self-consistent numerical N-body simulations to identify fully resonant initial conditions, whose dynamical evolution is characterized by an eccentric phase of the ice giants, as well as planetary scattering. We find a total of eight such initial conditions. Four of these primordial states are compatible with the canonical 'Nice' model, while the others imply slightly different evolutions. The results presented here should prove useful in further development of a comprehensive model for solar system formation.

  9. An alternative phase-space distribution to sample initial conditions for classical dynamics simulations

    International Nuclear Information System (INIS)

    Garcia-Vela, A.

    2002-01-01

    A new quantum-type phase-space distribution is proposed in order to sample initial conditions for classical trajectory simulations. The phase-space distribution is obtained as the modulus of a quantum phase-space state of the system, defined as the direct product of the coordinate and momentum representations of the quantum initial state. The distribution is tested by sampling initial conditions which reproduce the initial state of the Ar-HCl cluster prepared by ultraviolet excitation, and by simulating the photodissociation dynamics by classical trajectories. The results are compared with those of a wave packet calculation, and with a classical simulation using an initial phase-space distribution recently suggested. A better agreement is found between the classical and the quantum predictions with the present phase-space distribution, as compared with the previous one. This improvement is attributed to the fact that the phase-space distribution propagated classically in this work resembles more closely the shape of the wave packet propagated quantum mechanically

  10. Spinning in different directions: western rock lobster larval condition varies with eddy polarity, but does their diet?

    OpenAIRE

    O'Rorke, R.; Jeffs, A. G.; Wang, M.; Waite, A. M.; Beckley, L. E.; Lavery, S. D.

    2015-01-01

    Larvae of the western rock lobster (Panulirus cygnus) that occur in the south-east Indian Ocean offshore of Western Australia have been found to be in poorer nutritional condition in anticyclonic compared with cyclonic mesoscale eddies. The reason for this is unknown, but culture-based experiments have shown that diet composition and water temperature are key determinants of phyllosoma health and survival. Whether differences in prey composition are the cause of poor phyllosoma co...

  11. Effects of varying environmental conditions on emissivity spectra of bulk lunar soils: Application to Diviner thermal infrared observations of the Moon

    Science.gov (United States)

    Donaldson Hanna, K. L.; Greenhagen, B. T.; Patterson, W. R.; Pieters, C. M.; Mustard, J. F.; Bowles, N. E.; Paige, D. A.; Glotch, T. D.; Thompson, C.

    2017-02-01

    Currently, few thermal infrared measurements exist of fine particulate (samples (e.g. minerals, mineral mixtures, rocks, meteorites, and lunar soils) measured under simulated lunar conditions. Such measurements are fundamental for interpreting thermal infrared (TIR) observations by the Diviner Lunar Radiometer Experiment (Diviner) onboard NASA's Lunar Reconnaissance Orbiter as well as future TIR observations of the Moon and other airless bodies. In this work, we present thermal infrared emissivity measurements of a suite of well-characterized Apollo lunar soils and a fine particulate (sample as we systematically vary parameters that control the near-surface environment in our vacuum chamber (atmospheric pressure, incident solar-like radiation, and sample cup temperature). The atmospheric pressure is varied between ambient (1000 mbar) and vacuum (radiation is varied between 52 and 146 mW/cm2, and the sample cup temperature is varied between 325 and 405 K. Spectral changes are characterized as each parameter is varied, which highlight the sensitivity of thermal infrared emissivity spectra to the atmospheric pressure and the incident solar-like radiation. Finally spectral measurements of Apollo 15 and 16 bulk lunar soils are compared with Diviner thermal infrared observations of the Apollo 15 and 16 sampling sites. This comparison allows us to constrain the temperature and pressure conditions that best simulate the near-surface environment of the Moon for future laboratory measurements and to better interpret lunar surface compositions as observed by Diviner.

  12. Evolution of deformation structures under varying loading conditions followed in situ by high angular resolution 3DXRD

    DEFF Research Database (Denmark)

    Pantleon, Wolfgang; Wejdemann, Christian; Jakobsen, B.

    2009-01-01

    copper to different loading conditions are presented: during uninterrupted tensile deformation, formation of subgrains can be observed concurrently with broadening of the Bragg reflection shortly after onset of plastic deformation. With continued tensile deformation, the subgrain structure develops...... intermittently. When the traction is terminated, stress relaxation occurs and number, size and orientation of subgrains are found to be constant. The subgrain structure freezes and only a minor clean-up of the dislocation structure is observed. When changing the tensile direction after pre-deformation in tension...

  13. A new Method for the Estimation of Initial Condition Uncertainty Structures in Mesoscale Models

    Science.gov (United States)

    Keller, J. D.; Bach, L.; Hense, A.

    2012-12-01

    The estimation of fast growing error modes of a system is a key interest of ensemble data assimilation when assessing uncertainty in initial conditions. Over the last two decades three methods (and variations of these methods) have evolved for global numerical weather prediction models: ensemble Kalman filter, singular vectors and breeding of growing modes (or now ensemble transform). While the former incorporates a priori model error information and observation error estimates to determine ensemble initial conditions, the latter two techniques directly address the error structures associated with Lyapunov vectors. However, in global models these structures are mainly associated with transient global wave patterns. When assessing initial condition uncertainty in mesoscale limited area models, several problems regarding the aforementioned techniques arise: (a) additional sources of uncertainty on the smaller scales contribute to the error and (b) error structures from the global scale may quickly move through the model domain (depending on the size of the domain). To address the latter problem, perturbation structures from global models are often included in the mesoscale predictions as perturbed boundary conditions. However, the initial perturbations (when used) are often generated with a variant of an ensemble Kalman filter which does not necessarily focus on the large scale error patterns. In the framework of the European regional reanalysis project of the Hans-Ertel-Center for Weather Research we use a mesoscale model with an implemented nudging data assimilation scheme which does not support ensemble data assimilation at all. In preparation of an ensemble-based regional reanalysis and for the estimation of three-dimensional atmospheric covariance structures, we implemented a new method for the assessment of fast growing error modes for mesoscale limited area models. The so-called self-breeding is development based on the breeding of growing modes technique

  14. Quantifying uncertainty in Gulf of Mexico forecasts stemming from uncertain initial conditions

    KAUST Repository

    Iskandarani, Mohamed

    2016-06-09

    Polynomial Chaos (PC) methods are used to quantify the impacts of initial conditions uncertainties on oceanic forecasts of the Gulf of Mexico circulation. Empirical Orthogonal Functions are used as initial conditions perturbations with their modal amplitudes considered as uniformly distributed uncertain random variables. These perturbations impact primarily the Loop Current system and several frontal eddies located in its vicinity. A small ensemble is used to sample the space of the modal amplitudes and to construct a surrogate for the evolution of the model predictions via a nonintrusive Galerkin projection. The analysis of the surrogate yields verification measures for the surrogate\\'s reliability and statistical information for the model output. A variance analysis indicates that the sea surface height predictability in the vicinity of the Loop Current is limited to about 20 days. © 2016. American Geophysical Union. All Rights Reserved.

  15. Kinetics of gamma quanta initiated difluoroethane chlorization in inert solvent in dynamic conditions

    International Nuclear Information System (INIS)

    Begishev, I.R.; Poluehktov, V.A.

    1979-01-01

    Studied is the kinetics of asymmetric difluoroethane chlorination under dynamic conditions where difluoroethane and chlorine are passed through liquid tetrachloromethane layer. It is shown that initiating chlorination of asymmetric difluoroethane by gamma quanta in the dose and temperature ranges of 2-50 rad/s and -30-100 deg C respectively brings to the significant increase of the reaction rate and unusually high trend for halogenated hydrocarbons, i.e. practically 1, 1, 1 - difluorochloroethane with quantitative yield is formed. In this case radiation chemical yield G=10 4 -10 5 is achieved. It is shown that the chlorination process under dynamic conditions, complicated by the transport of initial reagents from a gas phase to a liquid one and reaction products from a liquid phase to a gas one, is described satisfactorily by the model of ideal substitution reactor

  16. Anomalous transport in cellular flows: The role of initial conditions and aging

    Science.gov (United States)

    Pöschke, Patrick; Sokolov, Igor M.; Nepomnyashchy, Alexander A.; Zaks, Michael A.

    2016-09-01

    We consider the diffusion-advection problem in two simple cellular flow models (often invoked as examples of subdiffusive tracer motion) and concentrate on the intermediate time range, in which the tracer motion indeed may show subdiffusion. We perform extensive numerical simulations of the systems under different initial conditions and show that the pure intermediate-time subdiffusion regime is only evident when the particles start at the border between different cells, i.e., at the separatrix, and is less pronounced or absent for other initial conditions. The motion moreover shows quite peculiar aging properties, which are also mirrored in the behavior of the time-averaged mean squared displacement for single trajectories. This kind of behavior is due to the complex motion of tracers trapped inside the cell and is absent in classical models based on continuous-time random walks with no dynamics in the trapped state.

  17. Abstract fractional integro-differential equations involving nonlocal initial conditions in α-norm

    Directory of Open Access Journals (Sweden)

    Wang Rong-Nian

    2011-01-01

    Full Text Available Abstract In the present paper, we deal with the Cauchy problems of abstract fractional integro-differential equations involving nonlocal initial conditions in α-norm, where the operator A in the linear part is the generator of a compact analytic semigroup. New criterions, ensuring the existence of mild solutions, are established. The results are obtained by using the theory of operator families associated with the function of Wright type and the semigroup generated by A, Krasnoselkii's fixed point theorem and Schauder's fixed point theorem. An application to a fractional partial integro-differential equation with nonlocal initial condition is also considered. Mathematics subject classification (2000 26A33, 34G10, 34G20

  18. Non-Gaussian initial conditions in ΛCDM: Newtonian, relativistic, and primordial contributions

    International Nuclear Information System (INIS)

    Bruni, Marco; Hidalgo, Juan Carlos; Meures, Nikolai; Wands, David

    2014-01-01

    The goal of the present paper is to set initial conditions for structure formation at nonlinear order, consistent with general relativity, while also allowing for primordial non-Gaussianity. We use the nonlinear continuity and Raychaudhuri equations, which together with the nonlinear energy constraint, determine the evolution of the matter density fluctuation in general relativity. We solve this equations at first and second order in a perturbative expansion, recovering and extending previous results derived in the matter-dominated limit and in the Newtonian regime. We present a second-order solution for the comoving density contrast in a ΛCDM universe, identifying nonlinear contributions coming from the Newtonian growing mode, primordial non-Gaussianity and intrinsic non-Gaussianity, due to the essential nonlinearity of the relativistic constraint equations. We discuss the application of these results to initial conditions in N-body simulations, showing that relativistic corrections mimic a non-zero nonlinear parameter f NL

  19. Quantification of discreteness effects in cosmological N-body simulations: Initial conditions

    International Nuclear Information System (INIS)

    Joyce, M.; Marcos, B.

    2007-01-01

    The relation between the results of cosmological N-body simulations, and the continuum theoretical models they simulate, is currently not understood in a way which allows a quantification of N dependent effects. In this first of a series of papers on this issue, we consider the quantification of such effects in the initial conditions of such simulations. A general formalism developed in [A. Gabrielli, Phys. Rev. E 70, 066131 (2004).] allows us to write down an exact expression for the power spectrum of the point distributions generated by the standard algorithm for generating such initial conditions. Expanded perturbatively in the amplitude of the input (i.e. theoretical, continuum) power spectrum, we obtain at linear order the input power spectrum, plus two terms which arise from discreteness and contribute at large wave numbers. For cosmological type power spectra, one obtains as expected, the input spectrum for wave numbers k smaller than that characteristic of the discreteness. The comparison of real space correlation properties is more subtle because the discreteness corrections are not as strongly localized in real space. For cosmological type spectra the theoretical mass variance in spheres and two-point correlation function are well approximated above a finite distance. For typical initial amplitudes this distance is a few times the interparticle distance, but it diverges as this amplitude (or, equivalently, the initial redshift of the cosmological simulation) goes to zero, at fixed particle density. We discuss briefly the physical significance of these discreteness terms in the initial conditions, in particular, with respect to the definition of the continuum limit of N-body simulations

  20. Assessing initial conditions for chloride transport across low-permeability argillaceous rocks, Wellenberg, Switzerland

    International Nuclear Information System (INIS)

    Waber, H.N.; Hobbs, M.Y.; Frape, S.K.

    2013-01-01

    Information about fluid evolution and solute transport in a low-permeability metamorphic rock sequence has been obtained by comparing chloride concentrations and chlorine isotope ratios of pore water, groundwater, and fluid inclusions. The similarity of δ 37 Cl values in fluid inclusions and groundwater suggests a closed-system evolution during the metamorphic overprint, and signatures established at this time appear to form the initial conditions for chloride transport after exhumation of the rock sequence. (authors)

  1. Assessment of initial soil moisture conditions for event-based rainfall-runoff modelling

    OpenAIRE

    Tramblay, Yves; Bouvier, Christophe; Martin, C.; Didon-Lescot, J. F.; Todorovik, D.; Domergue, J. M.

    2010-01-01

    Flash floods are the most destructive natural hazards that occur in the Mediterranean region. Rainfall-runoff models can be very useful for flash flood forecasting and prediction. Event-based models are very popular for operational purposes, but there is a need to reduce the uncertainties related to the initial moisture conditions estimation prior to a flood event. This paper aims to compare several soil moisture indicators: local Time Domain Reflectometry (TDR) measurements of soil moisture,...

  2. Assessing initial conditions for chloride transport across low-permeability argillaceous rocks, Wellenberg, Switzerland

    Energy Technology Data Exchange (ETDEWEB)

    Waber, H.N. [Rock-Water Interaction Group, Institute of Geological Sciences, University of Bern, Baltzerstrasse 1-3, 3012 Bern (Switzerland); Hobbs, M.Y. [Rock-Water Interaction Group, Institute of Geological Sciences, University of Bern, Baltzerstrasse 1-3, 3012 Bern (Switzerland); Nuclear Waste Management Organization (NWMO), 22 St. Clair Avenue East, M4T 2S3 Toronto, Ontario (Canada); Frape, S.K. [Department of Earth and Environmental Sciences, University of Waterloo, Waterloo, Ontario (Canada)

    2013-07-01

    Information about fluid evolution and solute transport in a low-permeability metamorphic rock sequence has been obtained by comparing chloride concentrations and chlorine isotope ratios of pore water, groundwater, and fluid inclusions. The similarity of δ{sup 37}Cl values in fluid inclusions and groundwater suggests a closed-system evolution during the metamorphic overprint, and signatures established at this time appear to form the initial conditions for chloride transport after exhumation of the rock sequence. (authors)

  3. Discretizing LTI Descriptor (Regular Differential Input Systems with Consistent Initial Conditions

    Directory of Open Access Journals (Sweden)

    Athanasios D. Karageorgos

    2010-01-01

    Full Text Available A technique for discretizing efficiently the solution of a Linear descriptor (regular differential input system with consistent initial conditions, and Time-Invariant coefficients (LTI is introduced and fully discussed. Additionally, an upper bound for the error ‖x¯(kT−x¯k‖ that derives from the procedure of discretization is also provided. Practically speaking, we are interested in such kind of systems, since they are inherent in many physical, economical and engineering phenomena.

  4. Flow behaviour in a CANDU horizontal fuel channel from stagnant subcooled initial conditions

    International Nuclear Information System (INIS)

    Caplan, M.Z.; Gulshani, P.; Holmes, R.W.; Wright, A.C.D.

    1984-01-01

    The flow behaviour in a CANDU primary system with horizontal fuel channels is described following a small inlet header break. With the primary pumps running, emergency coolant injection is in the forward direction so that the channel outlet feeders remain warmer than the inlet thereby promoting forward natural circulation. However, the break force opposes the forward driving force. Should the primary pumps run down after the circuit has refilled, there is a break size for which the natural circulation force is balanced by the break force and channels could, theoretically, stagnate. Result of visualization and of full-size channel tests on channel flow behaviour from an initially stagnant channel condition are discussed. After a channel stagnation, the decay power heats the coolant to saturation. Steam is then formed and the coolant stratifies. The steam expands into the subcooled water in the end fitting in a chugging type of flow regime due to steam condensation. After the end fitting reaches the saturation temperature, steam is able to penetrate into the vertical feeder thereby initiating a large buoyancy induced flow which refills the channel. The duration of stagnation is shown to be sensitive to small asymmetries in the initial conditions. A small initial flow can significantly shorten the occurrence and/or duration of boiling as has been confirmed by reactor experience. (author)

  5. The shear-free condition and constant-mean-curvature hyperboloidal initial data

    International Nuclear Information System (INIS)

    Allen, Paul T; Allen, Iva Stavrov; Isenberg, James; Lee, John M

    2016-01-01

    We consider the Einstein–Maxwell-fluid constraint equations, and make use of the conformal method to construct and parametrize constant-mean-curvature hyperboloidal initial data sets that satisfy the shear-free condition. This condition is known to be necessary in order that a spacetime development admit a regular conformal boundary at future null infinity; see (Andersson and Chruściel 1994 Commun. Math. Phys. 161 533–68). We work with initial data sets in a variety of regularity classes, primarily considering those data sets whose geometries are weakly asymptotically hyperbolic , as defined in (Allen et al 2015 arXiv:1506.03399). These metrics are C 1,1 conformally compact, but not necessarily C 2 conformally compact. In order to ensure that the data sets we construct are indeed shear-free, we make use of the conformally covariant traceless Hessian introduced in (Allen et al 2015 arXiv:1506.03399). We furthermore construct a class of initial data sets with weakly asymptotically hyerbolic metrics that may be only C 0,1 conformally compact; these data sets are insufficiently regular to make sense of the shear-free condition. (paper)

  6. Avoiding the blue spectrum and the fine-tuning of initial conditions in hybrid inflation

    International Nuclear Information System (INIS)

    Clesse, Sebastien; Rocher, Jonathan

    2009-01-01

    Hybrid inflation faces two well-known problems: the blue spectrum of the nonsupersymmetric version of the model and the fine-tuning of the initial conditions of the fields leading to sufficient inflation to account for the standard cosmological problems. They are investigated by studying the exact two-fields dynamics instead of assuming slow-roll. When the field values are restricted to be less than the reduced Planck mass, a non-negligible part of the initial condition space (around 15% depending on potential parameters) leads to successful inflation. Most of it is located outside the usual inflationary valley and organized in continuous patterns instead of being isolated as previously found. Their existence is explained and their properties are studied. This shows that no excessive fine-tuning is required for successful hybrid inflation. Moreover, by extending the initial condition space to Planckian-like or super-Planckian values, inflation becomes generically sufficiently long and can produce a red-tilted scalar power spectrum due to slow-roll violations. The robustness of these properties is confirmed by conducting our analysis on three other models of hybrid-type inflation in various framework: 'smooth' and 'shifted' inflation in SUSY and SUGRA, and 'radion assisted' gauge inflation. A high percentage of successful inflation for smooth hybrid inflation (up to 80%) is observed.

  7. Investigating the emerging role of comparative proteomics in the search for new biomarkers of metal contamination under varying abiotic conditions

    Energy Technology Data Exchange (ETDEWEB)

    Vellinger, Céline, E-mail: celine.vellinger@gmail.com [Laboratoire Interdisciplinaire des Environnements Continentaux (LIEC), CNRS UMR 7360, Université de Lorraine – Metz (France); Sohm, Bénédicte, E-mail: benedicte.sohm@univ-lorraine.fr [Laboratoire Interdisciplinaire des Environnements Continentaux (LIEC), CNRS UMR 7360, Université de Lorraine – Metz (France); Parant, Marc, E-mail: marc.parant@univ-lorraine.fr [Laboratoire Interdisciplinaire des Environnements Continentaux (LIEC), CNRS UMR 7360, Université de Lorraine – Metz (France); Immel, Françoise, E-mail: Francoise.Immel@u-bourgogne.fr [Biogéosciences, CNRS UMR 6282, Université de Bourgogne – Dijon (France); Usseglio-Polatera, Philippe, E-mail: philippe.usseglio-polatera@univ-lorraine.fr [Laboratoire Interdisciplinaire des Environnements Continentaux (LIEC), CNRS UMR 7360, Université de Lorraine – Metz (France)

    2016-08-15

    This study aims at investigating the potential use of comparative proteomics as a multi-marker approach of metal contamination, taking into account the potential confounding effect of water temperature. The major objective was to identify combinations of proteins specifically responding to a given metal, even if included in a metal mixture. The diagnostic approach was performed via the comparative analysis of protein expression on spot mapping provided by adult males of Gammarus pulex (Amphipoda, Crustacea) respectively exposed to arsenate (As), cadmium (Cd) or a binary mixture of these metals (AsCd) at three realistic temperatures (5, 10 and 15 °C). Proteomic expression analysis was performed by Differential in-Gel Electrophoresis (2D-DiGE), and completed by an adapted inferential statistical approach. Combinations of under/over-expressed protein spots discriminated the metal identity. However, none of these spots discriminated both the individual metal effect (As or Cd) and its effect in metal mixture (AsCd) whatever the tested temperature. Some limits of the two-dimensional analysis of protein spot maps in G. pulex have been highlighted: (i) the presence of contaminating peptides and/or abundant “déja-vu” proteins which can mask the responses of other proteins of interest or (ii) the presence of post-translational modifications. An optimization of the experimental design (especially during the sample preparation) has been described for future investigations. This study has also highlighted (i) the importance of precisely identifying the protein spots of interest to avoid erroneous interpretations in terms of action mechanisms of chemicals and (ii) the importance of working under controlled laboratory conditions with a temperature close to 10 °C. In such conditions, we have demonstrated a higher impact of As than Cd on the energetic metabolism of Gammarus. This As impact is reduced in AsCd mixture confirming the antagonistic interaction of this binary

  8. Investigating the emerging role of comparative proteomics in the search for new biomarkers of metal contamination under varying abiotic conditions

    International Nuclear Information System (INIS)

    Vellinger, Céline; Sohm, Bénédicte; Parant, Marc; Immel, Françoise; Usseglio-Polatera, Philippe

    2016-01-01

    This study aims at investigating the potential use of comparative proteomics as a multi-marker approach of metal contamination, taking into account the potential confounding effect of water temperature. The major objective was to identify combinations of proteins specifically responding to a given metal, even if included in a metal mixture. The diagnostic approach was performed via the comparative analysis of protein expression on spot mapping provided by adult males of Gammarus pulex (Amphipoda, Crustacea) respectively exposed to arsenate (As), cadmium (Cd) or a binary mixture of these metals (AsCd) at three realistic temperatures (5, 10 and 15 °C). Proteomic expression analysis was performed by Differential in-Gel Electrophoresis (2D-DiGE), and completed by an adapted inferential statistical approach. Combinations of under/over-expressed protein spots discriminated the metal identity. However, none of these spots discriminated both the individual metal effect (As or Cd) and its effect in metal mixture (AsCd) whatever the tested temperature. Some limits of the two-dimensional analysis of protein spot maps in G. pulex have been highlighted: (i) the presence of contaminating peptides and/or abundant “déja-vu” proteins which can mask the responses of other proteins of interest or (ii) the presence of post-translational modifications. An optimization of the experimental design (especially during the sample preparation) has been described for future investigations. This study has also highlighted (i) the importance of precisely identifying the protein spots of interest to avoid erroneous interpretations in terms of action mechanisms of chemicals and (ii) the importance of working under controlled laboratory conditions with a temperature close to 10 °C. In such conditions, we have demonstrated a higher impact of As than Cd on the energetic metabolism of Gammarus. This As impact is reduced in AsCd mixture confirming the antagonistic interaction of this binary

  9. The initial representation in reasoning towards an interpretation of conditional sentences.

    Science.gov (United States)

    Schroyens, Walter; Braem, Senne

    2011-02-01

    All accounts of human reasoning (whether presented at the symbolic or subsymbolic level) have to reckon with the temporal organization of the human processing systems and the ephemeral nature of the representations it uses. We present three new empirical tests for the hypothesis that people commence the interpretational process by constructing a minimal initial representation. In the case of if A then C the initial representation captures the occurrence of the consequent, C, within the context of the antecedent, A. Conditional inference problems are created by a categorical premise that affirms or denies A or C. The initial representation allows an inference when the explicitly represented information matches (e.g., the categorical premise A affirms the antecedent "A") but not when it mismatches (e.g., "not-A" denies A). Experiments 1 and 2 confirmed that people tend to accept the conclusion that "nothing follows" for the denial problems, as indeed they do not have a determinate initial-model conclusion. Experiment 3 demonstrated the other way round that the effect of problem type (affirmation versus denial) is reduced when we impede the possibility of inferring a determinate conclusion on the basis of the initial representation of both the affirmation and the denial problems.

  10. An empirical assessment of driver motivation and emotional states in perceived safety margins under varied driving conditions.

    Science.gov (United States)

    Zhang, Yu; Kaber, David B

    2013-01-01

    Motivation models in driving behaviour postulate that driver motives and emotional states dictate risk tolerance under various traffic conditions. The present study used time and driver performance-based payment systems to manipulate motivation and risk-taking behaviour. Ten participants drove to a predefined location in a simulated driving environment. Traffic patterns (density and velocity) were manipulated to cause driver behaviour adjustments due to the need to conform with the social norms of the roadway. The driving environment complexity was investigated as a mediating factor in risk tolerance. Results revealed the performance-based payment system to closely relate to risk-taking behaviour as compared with the time-based payment system. Drivers conformed with social norms associated with specific traffic patterns. Higher roadway complexity led to a more conservative safety margins and speeds. This research contributes to the further development of motivational models of driver behaviour. This study provides empirical justification for two motivation factors in driver risk-taking decisions, including compliance with social norm and emotions triggered by incentives. Environment complexity was identified as a mediating factor in motivational behaviour model. This study also recommended safety margin measures sensitive to changes in driver risk tolerance.

  11. Modulating the phenology and yield of camelina sativa L. by varying sowing dates under water deficit stress conditions

    Directory of Open Access Journals (Sweden)

    Ejaz Ahmad Waraich

    2017-05-01

    Full Text Available Camelina (Camelina sativa L. an oilseed crop has emerged as a potential source for biofuels and bio-products. Camelina is an economic crop due to its less requirements of agronomic inputs as compared to other oilseed crops. However, it is direly required to evaluate the adaptability of camelina and characterize its production potential. Therefore, a pot experiment was carried out in rain out shelter at the Department of Agronomy, University of Agriculture, Faisalabad, Pakistan to optimize appropriate sowing date with respect to growth and yield potential of different genotypes of camelina under drought stress. Completely randomized design with factorial arrangements was adopted. Three sowing dates with the difference of 10 days (November 13 th, 23rd and December 03rd, two water regimes (100% FC and 60% FC and two camlena genotypes (611 and 618 were used in this experiment. Results indicated that camelina growth and yield related traits were significantly influenced by difference in sowing dates and water regimes. Maximum leaf area index (LAI, crop growth rate (CGR, leaf area duration (LAD, net assimilation rate (NAR and yield related traits were recorded with early sowing (13th November which was followed by sowing on 23rd November and least values of these variables were recorded in late sowing (December 03rd. Plants grown under water deficit conditions (60% FC showed the decreased values of LAI, CGR, LAD, NAR and yield related attributes as compared to normally irrigated plants (100% FC. However, the response of genotypes of camelina 611 and 618 remained statistically similar to each other.

  12. Symbolic computation of analytic approximate solutions for nonlinear differential equations with initial conditions

    Science.gov (United States)

    Lin, Yezhi; Liu, Yinping; Li, Zhibin

    2012-01-01

    The Adomian decomposition method (ADM) is one of the most effective methods for constructing analytic approximate solutions of nonlinear differential equations. In this paper, based on the new definition of the Adomian polynomials, and the two-step Adomian decomposition method (TSADM) combined with the Padé technique, a new algorithm is proposed to construct accurate analytic approximations of nonlinear differential equations with initial conditions. Furthermore, a MAPLE package is developed, which is user-friendly and efficient. One only needs to input a system, initial conditions and several necessary parameters, then our package will automatically deliver analytic approximate solutions within a few seconds. Several different types of examples are given to illustrate the validity of the package. Our program provides a helpful and easy-to-use tool in science and engineering to deal with initial value problems. Program summaryProgram title: NAPA Catalogue identifier: AEJZ_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEJZ_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 4060 No. of bytes in distributed program, including test data, etc.: 113 498 Distribution format: tar.gz Programming language: MAPLE R13 Computer: PC Operating system: Windows XP/7 RAM: 2 Gbytes Classification: 4.3 Nature of problem: Solve nonlinear differential equations with initial conditions. Solution method: Adomian decomposition method and Padé technique. Running time: Seconds at most in routine uses of the program. Special tasks may take up to some minutes.

  13. Rare Earth Element Behavior During Incongruent Weathering and Varying Discharge Conditions in Silicate Dominated River Systems: The Australian Victorian Alps

    Science.gov (United States)

    Hagedorn, K. B.; Cartwright, I.

    2008-12-01

    The distribution of rare earth elements (REE) and trace elements was measured by ICP-MS on fresh, slightly weathered and weathered granite and surface water samples from a network of 11 pristine rivers draining the Australian Victorian Alps during (i) high and (ii) low discharge conditions. River water REE concentrations are largely derived from atmospheric precipitation (rain, snow), as indicated by similar Chondrite normalized REE patterns (higher LREE over HREE; negative Ce anomalies, positive Eu anomalies) and similar total REE concentrations during both dry and wet seasons. Calculations based on the covariance between REE and Cl concentrations and oxygen and hydrogen isotopes indicate precipitation input coupled with subsequent evaporation may account for 30% o 100% of dissolved REE in stream waters. The dissolved contribution to the granitic substratum to stream water comes mainly from the transformation of plagioclase to smectite, kaolinite and gibbsite and minor apatite dissolution. However, since most REE of the regional granite are present in accessory minerals (titanite, zircon, etc.) they do not significantly contribute to the river REE pool. REE concentrations drop sharply downstream as a result of dilution and chemical attenuation. A trend of downstream enrichment of the heavier REE is due to selective partitioning of the lighter REE (as both free REE or REECO3 complexes) to hydrous oxides of suspended Al which, in turn, is controlled by a downstream increase of pH to values > 6.1 (for free REE) and > 7.3 (for REECO3 complexes). Although most circumneutral waters were supersaturated with REE phosphate compounds, precipitation of LnPO4 is not believed to have been a dominant process because the predicted phosphate fractionation pattern is inconsistent with the observed trends. Negative saturation indices of hydrous ferric oxides also militate against surface complexation onto goethite. Instead, REE attenuation most likely resulted from adsorption onto

  14. Decoupling in an expanding universe boundary RG-flow affects initial conditions for inflation

    CERN Document Server

    Schalm, K; Van der Schaar, J P; Schalm, Koenraad; Shiu, Gary; Schaar, Jan Pieter van der

    2004-01-01

    We study decoupling in FRW spacetimes, emphasizing a Lagrangian description throughout. To account for the vacuum choice ambiguity in cosmological settings, we introduce an arbitrary boundary action representing the initial conditions. RG flow in these spacetimes naturally affects the boundary interactions. As a consequence the boundary conditions are sensitive to high-energy physics through irrelevant terms in the boundary action. Using scalar field theory as an example, we derive the leading dimension four irrelevant boundary operators. We discuss how the known vacuum choices, e.g. the Bunch-Davies vacuum, appear in the Lagrangian description and square with decoupling. For all choices of boundary conditions encoded by relevant boundary operators, of which the known ones are a subset, backreaction is under control. All, moreover, will generically feel the influence of high-energy physics through irrelevant (dimension four) boundary corrections. Having established a coherent effective field theory framework ...

  15. Validation of the criteria for initiating the cleaning of heating, ventilation, and air-conditioning (HVAC) ductwork under real conditions.

    Science.gov (United States)

    Lavoie, Jacques; Marchand, Geneviève; Cloutier, Yves; Lavoué, Jérôme

    2011-08-01

    Dust accumulation in the components of heating, ventilation, and air-conditioning (HVAC) systems is a potential source of contaminants. To date, very little information is available on recognized methods for assessing dust buildup in these systems. The few existing methods are either objective in nature, involving numerical values, or subjective in nature, based on experts' judgments. An earlier project aimed at assessing different methods of sampling dust in ducts was carried out in the laboratories of the Institut de recherche Robert-Sauvé en santé et en sécurité du travail (IRSST). This laboratory study showed that all the sampling methods were practicable, provided that a specific surface-dust cleaning initiation criterion was used for each method. However, these conclusions were reached on the basis of ideal conditions in a laboratory using a reference dust. The objective of this present study was to validate these laboratory results in the field. To this end, the laboratory sampling templates were replicated in real ducts and the three sampling methods (the IRSST method, the method of the U.S. organization National Air Duct Cleaner Association [NADCA] and that of the French organization Association pour la Prévention et l'Étude de la Contamination [ASPEC]) were used simultaneously in a statistically representative number of systems. The air return and supply ducts were also compared. Cleaning initiation criteria under real conditions were found to be 6.0 mg/100 cm(2) using the IRSST method, 2.0 mg/100 cm(2) using the NADCA method, and 23 mg/100 cm(2) using the ASPEC method. In the laboratory study, the criteria using the same methods were 6.0 for the IRSST method, 2.0 for the NADCA method, and 3.0 for the ASPEC method. The laboratory criteria for the IRSST and NADCA methods were therefore validated in the field. The ASPEC criterion was the only one to change. The ASPEC method therefore allows for the most accurate evaluation of dust accumulation in HVAC

  16. Processes influencing migration of bioavailable organic compounds from polymers - investigated during biotic and abiotic testing under static and non-static conditions with varying S/V-ratios

    DEFF Research Database (Denmark)

    Corfitzen, Charlotte B.; Arvin, Erik; Albrechtsen, Hans-Jørgen

    . The bioavailable migration from the polymer surface was influence by diffusion over the solid-liquid boundary layer under sterile conditions, which resulted in an inversely proportionally relationship between bioavailable migration expressed per unit surface area of material and the surface to volume ratio (S/V-ratio...... the effect of the boundary layer, since bioavailable migration was continuously consumed by the bacteria. Thus the driving force for the diffusion process was maintained at a maximum, thereby enhancing the bioavailable migration from the material surfaces. Thus neither non-static conditions nor varying S/V-ratios...

  17. Creep rupture properties under varying load/temperature conditions on a nickel-base heat-resistant alloy strengthened by boron addition

    International Nuclear Information System (INIS)

    Tsuji, Hirokazu; Tanabe, Tatsuhiko; Nakajima, Hajime

    1994-01-01

    A series of constant load and temperature creep rupture tests and varying load and temperature creep rupture tests was carried out on Hastelloy XR whose boron content level is 60 mass ppm at 900 and 1000 C in order to examine the behavior of the alloy under varying load and temperature conditions. The life fraction rule completely fails in the prediction of the creep rupture life under varying load and temperature conditions though the rule shows good applicability for Hastelloy XR whose boron content level is below 10 mass ppm. The modified life fraction rule has been proposed based on the dependence of the creep rupture strength on the boron content level of the alloy. The modified rule successfully predicts the creep rupture life under the test conditions from 1000 to 900 C. The trend observed in the tests from 900 to 1000 C can be qualitatively explained by the mechanism that the oxide film which is formed during the prior exposure to 900 C plays the role of the protective barrier against the boron dissipation into the environment. (orig.)

  18. Creep rupture properties under varying load/temperature conditions on a nickel-base heat-resistant alloy strengthened by boron addition

    International Nuclear Information System (INIS)

    Tsuji, Hirokazu; Nakajima, Hajime; Tanabe, Tatsuhiko.

    1993-09-01

    A series of constant load and temperature creep rupture tests and varying load and temperature creep rupture tests was carried out on Hastelloy XR whose boron content level is 60 mass ppm at 900 and 1000degC in order to examine the behavior of the alloy under varying load and temperature conditions. The life fraction rule completely fails in the prediction of the creep rupture life under varying load and temperature conditions though the rule shows good applicability for Hastelloy XR whose boron content level is below 10 mass ppm. The modified life fraction rule has been proposed based on the dependence of the creep rupture strength on the born content level of the alloy. The modified rule successfully predicts the creep rupture life under the test conditions from 1000degC to 900degC. The trend observed in the tests from 900degC to 1000degC can be qualitatively explained by the mechanism that the oxide film which is formed during the prior exposure to 900degC plays the role of the protective barrier against the boron dissipation into the environment. (author)

  19. High throughput nanostructure-initiator mass spectrometry screening of microbial growth conditions for maximal β-glucosidase production.

    Science.gov (United States)

    Cheng, Xiaoliang; Hiras, Jennifer; Deng, Kai; Bowen, Benjamin; Simmons, Blake A; Adams, Paul D; Singer, Steven W; Northen, Trent R

    2013-01-01

    Production of biofuels via enzymatic hydrolysis of complex plant polysaccharides is a subject of intense global interest. Microbial communities are known to express a wide range of enzymes necessary for the saccharification of lignocellulosic feedstocks and serve as a powerful reservoir for enzyme discovery. However, the growth temperature and conditions that yield high cellulase activity vary widely, and the throughput to identify optimal conditions has been limited by the slow handling and conventional analysis. A rapid method that uses small volumes of isolate culture to resolve specific enzyme activity is needed. In this work, a high throughput nanostructure-initiator mass spectrometry (NIMS)-based approach was developed for screening a thermophilic cellulolytic actinomycete, Thermobispora bispora, for β-glucosidase production under various growth conditions. Media that produced high β-glucosidase activity were found to be I/S + glucose or microcrystalline cellulose (MCC), Medium 84 + rolled oats, and M9TE + MCC at 45°C. Supernatants of cell cultures grown in M9TE + 1% MCC cleaved 2.5 times more substrate at 45°C than at all other temperatures. While T. bispora is reported to grow optimally at 60°C in Medium 84 + rolled oats and M9TE + 1% MCC, approximately 40% more conversion was observed at 45°C. This high throughput NIMS approach may provide an important tool in discovery and characterization of enzymes from environmental microbes for industrial and biofuel applications.

  20. High throughput nanostructure-initiator mass spectrometry screening of microbial growth conditions for maximal β-glucosidase production

    Directory of Open Access Journals (Sweden)

    Xiaoliang eCheng

    2013-12-01

    Full Text Available Production of biofuels via enzymatic hydrolysis of complex plant polysaccharides is a subject of intense global interest. Microbial communities are known to express a wide range of enzymes necessary for the saccharification of lignocellulosic feedstocks and serve as a powerful reservoir for enzyme discovery. However, the growth temperature and conditions that yield high cellulase activity vary widely, and the throughput to identify optimal conditions has been limited by the slow handling and conventional analysis. A rapid method that uses small volumes of isolate culture to resolve specific enzyme activity is needed. In this work, a high throughput nanostructure-initiator mass spectrometry (NIMS based approach was developed for screening a thermophilic cellulolytic actinomycete, Thermobispora bispora, for β-glucosidase production under various growth conditions. Media that produced high β-glucosidase activity were found to be I/S + glucose or microcrystalline cellulose (MCC, Medium 84 + rolled oats, and M9TE + MCC at 45 °C. Supernatants of cell cultures grown in M9TE + 1% MCC cleaved 2.5 times more substrate at 45 °C than at all other temperatures. While T. bispora is reported to grow optimally at 60 °C in Medium 84 + rolled oats and M9TE + 1% MCC, approximately 40% more conversion was observed at 45 °C. This high throughput NIMS approach may provide an important tool in discovery and characterization of enzymes from environmental microbes for industrial and biofuel applications.

  1. Greenland Regional and Ice Sheet-wide Geometry Sensitivity to Boundary and Initial conditions

    Science.gov (United States)

    Logan, L. C.; Narayanan, S. H. K.; Greve, R.; Heimbach, P.

    2017-12-01

    Ice sheet and glacier model outputs require inputs from uncertainly known initial and boundary conditions, and other parameters. Conservation and constitutive equations formalize the relationship between model inputs and outputs, and the sensitivity of model-derived quantities of interest (e.g., ice sheet volume above floatation) to model variables can be obtained via the adjoint model of an ice sheet. We show how one particular ice sheet model, SICOPOLIS (SImulation COde for POLythermal Ice Sheets), depends on these inputs through comprehensive adjoint-based sensitivity analyses. SICOPOLIS discretizes the shallow-ice and shallow-shelf approximations for ice flow, and is well-suited for paleo-studies of Greenland and Antarctica, among other computational domains. The adjoint model of SICOPOLIS was developed via algorithmic differentiation, facilitated by the source transformation tool OpenAD (developed at Argonne National Lab). While model sensitivity to various inputs can be computed by costly methods involving input perturbation simulations, the time-dependent adjoint model of SICOPOLIS delivers model sensitivities to initial and boundary conditions throughout time at lower cost. Here, we explore both the sensitivities of the Greenland Ice Sheet's entire and regional volumes to: initial ice thickness, precipitation, basal sliding, and geothermal flux over the Holocene epoch. Sensitivity studies such as described here are now accessible to the modeling community, based on the latest version of SICOPOLIS that has been adapted for OpenAD to generate correct and efficient adjoint code.

  2. Initial experience with computed tomographic colonography applied for noncolorectal cancerous conditions

    International Nuclear Information System (INIS)

    Ichikawa, Tamaki; Kawada, Shuichi; Hirata, Satoru; Ikeda, Shu; Sato, Yuuki; Imai, Yutaka

    2011-01-01

    The aim of this study was to asses retrospectively the performance of computed tomography colonography (CTC) for noncolorectal cancerous conditions. A total of 44 patients with non-colorectal cancerous conditions underwent CTC. We researched the indications for CTC or present illness and evaluated the CTC imaging findings. We assessed whether diagnosis by CTC reduced conventional colonoscopic examinations. A total of 47 examinations were performed in 44 patients. The indications for CTC or a present illness were as follows: 15 patients with impossible or incomplete colonoscopy, 7 with diverticular disease, 6 with malignancy (noncolorectal cancer), 6 with Crohn's disease, 4 suspected to have a submucosal tumor on colonoscopy, 2 with ischemic colitis, and 4 with various other diseases. Colonic findings were diagnosed on CTC in 36 examinations, and extracolonic findings were identified in 35 of 44 patients. In all, 17 patients had undergone colonoscopy previously, 9 (52.9%) of whom did not require further colonoscopy by CTC. Five patients underwent colonoscopy after CTC. The indications for CTC were varied for patients with noncolorectal cancerous conditions. CTC examinations could be performed safely. Unlike colonoscopy or CT without preparation, CTC revealed colonic and extracolonic findings and may reduce the indication of colonoscopy in patients with noncolorectal cancerous conditions. (author)

  3. Initial growth of Bauhinia variegata trees under different colored shade nets and light conditions

    Directory of Open Access Journals (Sweden)

    Renata Bachin Mazzini-Guedes

    2014-12-01

    Full Text Available Bauhinia variegata and B. variegata var. candida, commonly known as orchid trees, are small sized trees widely used for urban forestry and landscaping. Adult plants grow under full sun; in Brazil, however, seedlings are generally cultivated in commercial nurseries under natural half-shading. The objective of this study was to evaluate the influence of different colored shade nets and light conditions on the initial growth of B. variegata and B. variegata var. candida. The influence of six light conditions (red net with 50% shading; blue net with 50% shading; black net with 70% shading; black net with 50% shading; black net with 30% shading; and full sun on the initial growth of B. variegata and B. variegata var. candida were evaluated along 160 days, and growth relationships were calculated. Seedlings showed more efficiency on the use of photoassimilated compounds when grown under full sun. Such condition is the most appropriate for seedling production of B. variegata and B. variegata var. candida, contradicting what has been performed in practice.

  4. Reduction of damage initiation density in fused silica optics via UV laser conditioning

    Science.gov (United States)

    Peterson, John E.; Maricle, Stephen M.; Brusasco, Raymond M.; Penetrante, Bernardino M.

    2004-03-16

    The present invention provides a method for reducing the density of sites on the surface of fused silica optics that are prone to the initiation of laser-induced damage, resulting in optics which have far fewer catastrophic defects and are better capable of resisting optical deterioration upon exposure for a long period of time to a high-power laser beam having a wavelength of about 360 nm or less. The initiation of laser-induced damage is reduced by conditioning the optic at low fluences below levels that normally lead to catastrophic growth of damage. When the optic is then irradiated at its high fluence design limit, the concentration of catastrophic damage sites that form on the surface of the optic is greatly reduced.

  5. Chimera states and the interplay between initial conditions and non-local coupling

    Science.gov (United States)

    Kalle, Peter; Sawicki, Jakub; Zakharova, Anna; Schöll, Eckehard

    2017-03-01

    Chimera states are complex spatio-temporal patterns that consist of coexisting domains of coherent and incoherent dynamics. We study chimera states in a network of non-locally coupled Stuart-Landau oscillators. We investigate the impact of initial conditions in combination with non-local coupling. Based on an analytical argument, we show how the coupling phase and the coupling strength are linked to the occurrence of chimera states, flipped profiles of the mean phase velocity, and the transition from a phase- to an amplitude-mediated chimera state.

  6. Initial conditions for slow-roll inflation in a random Gaussian landscape

    Energy Technology Data Exchange (ETDEWEB)

    Masoumi, Ali; Vilenkin, Alexander; Yamada, Masaki, E-mail: ali@cosmos.phy.tufts.edu, E-mail: vilenkin@cosmos.phy.tufts.edu, E-mail: Masaki.Yamada@tufts.edu [Institute of Cosmology, Department of Physics and Astronomy, Tufts University, Medford, MA 02155 (United States)

    2017-07-01

    In the landscape perspective, our Universe begins with a quantum tunneling from an eternally-inflating parent vacuum, followed by a period of slow-roll inflation. We investigate the tunneling process and calculate the probability distribution for the initial conditions and for the number of e-folds of slow-roll inflation, modeling the landscape by a small-field one-dimensional random Gaussian potential. We find that such a landscape is fully consistent with observations, but the probability for future detection of spatial curvature is rather low, P ∼ 10{sup −3}.

  7. Necessary conditions for the initiation and propagation of nuclear-detonation waves in plane atmospheres

    International Nuclear Information System (INIS)

    Weaver, T.A.; Wood, L.

    1979-01-01

    The basic conditions for the initiation of a nuclear-detonation wave in an atmosphere having plane symmetry (e.g., a thin, layered fluid envelope on a planet or star) are developed. Two classes of such a detonation are identified: those in which the temperature of the plasma is comparable to that of the electromagnetic radiation permeating it, and those in which the temperature of the plasma is much higher. Necessary conditions are developed for the propagation of such detonation waves for an arbitrarily great distance. The contribution of fusion chain reactions to these processes is evaluated. By means of these considerations, it is shown that neither the atmosphere nor oceans of the Earth may be made to undergo propagating nuclear detonation under any circumstances

  8. Exact solution for four-order acousto-optic Bragg diffraction with arbitrary initial conditions.

    Science.gov (United States)

    Pieper, Ron; Koslover, Deborah; Poon, Ting-Chung

    2009-03-01

    An exact solution to the four-order acousto-optic (AO) Bragg diffraction problem with arbitrary initial conditions compatible with exact Bragg angle incident light is developed. The solution, obtained by solving a 4th-order differential equation, is formalized into a transition matrix operator predicting diffracted light orders at the exit of the AO cell in terms of the same diffracted light orders at the entrance. It is shown that the transition matrix is unitary and that this unitary matrix condition is sufficient to guarantee energy conservation. A comparison of analytical solutions with numerical predictions validates the formalism. Although not directly related to the approach used to obtain the solution, it was discovered that all four generated eigenvalues from the four-order AO differential matrix operator are expressed simply in terms of Euclid's Divine Proportion.

  9. INITIAL TEST WELL CONDITIONING AT NOPAL I URANIUM DEPOSIT, SIERRA PENA BLANCA, CHIHUAHUA, MEXICO

    Energy Technology Data Exchange (ETDEWEB)

    R.D. Oliver; J.C. Dinsmoor; S.J. Goldstein; I. Reyes; R. De La Garza

    2005-07-11

    Three test wells, PB-1, PB-2, and PB-3, were drilled at the Nopal I uranium deposit as part of a natural analogue study to evaluate radionuclide transport processes during March-April 2003. The initial pumping to condition the wells was completed during December 2003. The PB-1 well, drilled immediately adjacent to the Nopal I ore body, was continuously cored to a depth of 250 m, terminating 20 m below the top of the measured water level. The PB-2 and PB-3 wells, which were drilled on opposite sides of PB-1 at a radial distance of approximately 40 to 50 m outside of the remaining projected ore body, were also drilled to about 20 m below the top of the measured water level. Each test well was completed with 4-inch (10.2-cm) diameter PVC casing with a slotted liner below the water table. Initial conditioning of all three wells using a submersible pump at low pump rates [less than 1 gallon (3.8 1) per minute] resulted in measurable draw down and recoveries. The greatest drawdown ({approx}15 m) was observed in PB-2, whereas only minor (<1 m) drawdown occurred in PB-3. For PB-1 and PB-2, the water turbidity decreased as the wells were pumped and the pH values decreased, indicating that the contamination from the drilling fluid was reduced as the wells were conditioned. Test wells PB-1 and PB-2 showed increased inflow after several borehole volumes of fluid were removed, but their inflow rates remained less that the pumping rate. Test well PB-3 showed the smallest drawdown and least change in pH and conductivity during initial pumping and quickest recovery with a rise in measured water level after conditioning. The 195 gallons (750 l) of water pumped from PB-3 during conditioning was discharged through a household sponge. That sponge showed measurable gamma radiation, which decayed to background values in less than 12 hours. Preliminary interpretations include filtration of a radioisotope source with a short half-life or of a radioisotope that volatized as the sponge

  10. INITIAL TEST WELL CONDITIONING AT NOPAL I URANIUM DEPOSIT, SIERRA PENA BLANCA, CHIHUAHUA, MEXICO

    International Nuclear Information System (INIS)

    Oliver, R.D.; Dinsmoor, J.C.; Goldstein, S.J.; Reyes, I.; De La Garza, R.

    2005-01-01

    Three test wells, PB-1, PB-2, and PB-3, were drilled at the Nopal I uranium deposit as part of a natural analogue study to evaluate radionuclide transport processes during March-April 2003. The initial pumping to condition the wells was completed during December 2003. The PB-1 well, drilled immediately adjacent to the Nopal I ore body, was continuously cored to a depth of 250 m, terminating 20 m below the top of the measured water level. The PB-2 and PB-3 wells, which were drilled on opposite sides of PB-1 at a radial distance of approximately 40 to 50 m outside of the remaining projected ore body, were also drilled to about 20 m below the top of the measured water level. Each test well was completed with 4-inch (10.2-cm) diameter PVC casing with a slotted liner below the water table. Initial conditioning of all three wells using a submersible pump at low pump rates [less than 1 gallon (3.8 1) per minute] resulted in measurable draw down and recoveries. The greatest drawdown (∼15 m) was observed in PB-2, whereas only minor (<1 m) drawdown occurred in PB-3. For PB-1 and PB-2, the water turbidity decreased as the wells were pumped and the pH values decreased, indicating that the contamination from the drilling fluid was reduced as the wells were conditioned. Test wells PB-1 and PB-2 showed increased inflow after several borehole volumes of fluid were removed, but their inflow rates remained less that the pumping rate. Test well PB-3 showed the smallest drawdown and least change in pH and conductivity during initial pumping and quickest recovery with a rise in measured water level after conditioning. The 195 gallons (750 l) of water pumped from PB-3 during conditioning was discharged through a household sponge. That sponge showed measurable gamma radiation, which decayed to background values in less than 12 hours. Preliminary interpretations include filtration of a radioisotope source with a short half-life or of a radioisotope that volatized as the sponge dried

  11. Initiation and inhibition of pitting corrosion on reinforcing steel under natural corrosion conditions

    Energy Technology Data Exchange (ETDEWEB)

    Abd El Wanees, S., E-mail: s_wanees@yahoo.com [Chemistry Department, Faculty of Science, University of Tabuk, Tabuk (Saudi Arabia); Chemistry Department, Faculty of Science, Zagazig University, Zagazig 44519 (Egypt); Bahgat Radwan, A. [Center for Advanced Materials, Qatar University, Doha 2713 (Qatar); Alsharif, M.A. [Chemistry Department, Faculty of Science, University of Tabuk, Tabuk (Saudi Arabia); Abd El Haleem, S.M. [Chemistry Department, Faculty of Science, Zagazig University, Zagazig 44519 (Egypt)

    2017-04-01

    Initiation and inhibition of pitting corrosion on reinforcing steel in saturated, naturally aerated Ca(OH){sub 2} solutions, under natural corrosion conditions, are followed through measurements of corrosion current, electrochemical impedance spectroscopy and SEM investigation. Induction period for pit initiation and limiting corrosion current for pit propagation are found to depend on aggressive salt anion and cation-types, as well as, concentration. Ammonium chlorides and sulfates are more corrosive than the corresponding sodium salts. Benzotriazole and two of its derivatives are found to be good inhibitors for pitting corrosion of reinforcing steel. Adsorption of these compounds follows a Langmuir adsorption isotherm. The thermodynamic functions ΔE{sup ∗}, ΔH{sup ∗} and ΔS{sup ∗} for pitting corrosion processes in the absence and presence of inhibitor are calculated and discussed. - Highlights: • Cl{sup −} and SO{sub 4} {sup 2-} induce pitting corrosion on passive reinforcing steel. • Initiation and propagation of pitting depend on cation and anion types. • Inhibition is based on adsorption according to Langmuir isotherm.

  12. Initial growth of Costus longebracteolatus and Costus spiralis ‘French Kiss’ under different light conditions

    Directory of Open Access Journals (Sweden)

    Renata Bachin Mazzini-Guedes

    2016-12-01

    Full Text Available The Brazilian native Costus longebracteolatus and Costus spiralis ‘French Kiss’, in the family Costaceae, have been used as both cut flowers and cut foliage. It is known that Costus species grow better under partial shade, but studies on the influence of shading or light on plant growth, development, and flower production are still incipient. As this kind of information is essential on planning of planting, production, and agribusiness activities, the objective of this research was to evaluate the influence of different colored shade nets and light conditions on the initial growth of both C. longebracteolatus and C. spiralis ‘French Kiss’. Plants, obtained from cuttings of pseudostems, were cultivated under six light conditions, which comprised six treatments, along 270 days: red net with 50% shading, blue net with 50% shading, black net with 70% shading, black net with 50% shading, black net with 30% shading, and full sun. The initial growth of C. longebracteolatus (up to 270 days is more successful under the blue net with 50% shading, which promoted highest values of pseudostem length and dry matter of aerial part. For C. spiralis ‘French Kiss’ plants, both the red and blue nets with 50% shading implied best results and differed for the other treatments with greater pseudostem length. Plant exposure to full sun inhibited growth and development, and favored early leaf necrosis.

  13. The halo bispectrum in N-body simulations with non-Gaussian initial conditions

    Science.gov (United States)

    Sefusatti, E.; Crocce, M.; Desjacques, V.

    2012-10-01

    We present measurements of the bispectrum of dark matter haloes in numerical simulations with non-Gaussian initial conditions of local type. We show, in the first place, that the overall effect of primordial non-Gaussianity on the halo bispectrum is larger than on the halo power spectrum when all measurable configurations are taken into account. We then compare our measurements with a tree-level perturbative prediction, finding good agreement at large scales when the constant Gaussian bias parameter, both linear and quadratic, and their constant non-Gaussian corrections are fitted for. The best-fitting values of the Gaussian bias factors and their non-Gaussian, scale-independent corrections are in qualitative agreement with the peak-background split expectations. In particular, we show that the effect of non-Gaussian initial conditions on squeezed configurations is fairly large (up to 30 per cent for fNL = 100 at redshift z = 0.5) and results from contributions of similar amplitude induced by the initial matter bispectrum, scale-dependent bias corrections as well as from non-linear matter bispectrum corrections. We show, in addition, that effects at second order in fNL are irrelevant for the range of values allowed by cosmic microwave background and galaxy power spectrum measurements, at least on the scales probed by our simulations (k > 0.01 h Mpc-1). Finally, we present a Fisher matrix analysis to assess the possibility of constraining primordial non-Gaussianity with future measurements of the galaxy bispectrum. We find that a survey with a volume of about 10 h-3 Gpc3 at mean redshift z ≃ 1 could provide an error on fNL of the order of a few. This shows the relevance of a joint analysis of galaxy power spectrum and bispectrum in future redshift surveys.

  14. Cosmological Simulations with Scale-Free Initial Conditions. I. Adiabatic Hydrodynamics

    International Nuclear Information System (INIS)

    Owen, J.M.; Weinberg, D.H.; Evrard, A.E.; Hernquist, L.; Katz, N.

    1998-01-01

    We analyze hierarchical structure formation based on scale-free initial conditions in an Einstein endash de Sitter universe, including a baryonic component with Ω bary = 0.05. We present three independent, smoothed particle hydrodynamics (SPH) simulations, performed at two resolutions (32 3 and 64 3 dark matter and baryonic particles) and with two different SPH codes (TreeSPH and P3MSPH). Each simulation is based on identical initial conditions, which consist of Gaussian-distributed initial density fluctuations that have a power spectrum P(k) ∝ k -1 . The baryonic material is modeled as an ideal gas subject only to shock heating and adiabatic heating and cooling; radiative cooling and photoionization heating are not included. The evolution is expected to be self-similar in time, and under certain restrictions we identify the expected scalings for many properties of the distribution of collapsed objects in all three realizations. The distributions of dark matter masses, baryon masses, and mass- and emission-weighted temperatures scale quite reliably. However, the density estimates in the central regions of these structures are determined by the degree of numerical resolution. As a result, mean gas densities and Bremsstrahlung luminosities obey the expected scalings only when calculated within a limited dynamic range in density contrast. The temperatures and luminosities of the groups show tight correlations with the baryon masses, which we find can be well represented by power laws. The Press-Schechter (PS) approximation predicts the distribution of group dark matter and baryon masses fairly well, though it tends to overestimate the baryon masses. Combining the PS mass distribution with the measured relations for T(M) and L(M) predicts the temperature and luminosity distributions fairly accurately, though there are some discrepancies at high temperatures/luminosities. In general the three simulations agree well for the properties of resolved groups, where a group

  15. Importance of initial buoyancy field on evolution of mantle thermal structure: Implications of surface boundary conditions

    Directory of Open Access Journals (Sweden)

    Petar Glišović

    2015-01-01

    Full Text Available Although there has been significant progress in the seismic imaging of mantle heterogeneity, the outstanding issue that remains to be resolved is the unknown distribution of mantle temperature anomalies in the distant geological past that give rise to the present-day anomalies inferred by global tomography models. To address this question, we present 3-D convection models in compressible and self-gravitating mantle initialised by different hypothetical temperature patterns. A notable feature of our forward convection modelling is the use of self-consistent coupling of the motion of surface tectonic plates to the underlying mantle flow, without imposing prescribed surface velocities (i.e., plate-like boundary condition. As an approximation for the surface mechanical conditions before plate tectonics began to operate we employ the no-slip (rigid boundary condition. A rigid boundary condition demonstrates that the initial thermally-dominated structure is preserved, and its geographical location is fixed during the evolution of mantle flow. Considering the impact of different assumed surface boundary conditions (rigid and plate-like on the evolution of thermal heterogeneity in the mantle we suggest that the intrinsic buoyancy of seven superplumes is most-likely resolved in the tomographic images of present-day mantle thermal structure. Our convection simulations with a plate-like boundary condition reveal that the evolution of an initial cold anomaly beneath the Java-Indonesian trench system yields a long-term, stable pattern of thermal heterogeneity in the lowermost mantle that resembles the present-day Large Low Shear Velocity Provinces (LLSVPs, especially below the Pacific. The evolution of subduction zones may be, however, influenced by the mantle-wide flow driven by deeply-rooted and long-lived superplumes since Archean times. These convection models also detect the intrinsic buoyancy of the Perm Anomaly that has been identified as a unique

  16. TRANSFORMATION OF ECONOMY IN THE CONDITIONS OF FORMING THE NATIONAL TECHNOLOGICAL INITIATIVE

    Directory of Open Access Journals (Sweden)

    Elena Sibirskaya

    2017-12-01

    Full Text Available The relevance of the study is conditioned by the need for a clear idea about the upcoming transformation of the Russian economy for implementing the national technology initiative (NTI. Today, Russia is facing a “challenge of development”, which determines the necessity of transition to breakthrough scientific and technological development as a major strategic objective for the future, which definitely determines further socio-economic development. In his address to the Federal Assembly of December 4, 2014, Russian President Vladimir Putin outlined the National technology initiative to be one of the priorities of state policy. “On the basis of long-term forecasting it is necessary to understand what challenges Russia will face in 10-15 years, what advanced solutions will be required in order to ensure national security, high quality of life, development of new technological order” (from the message to the Federal Assembly [6]. The response to this challenge is the National technology initiative, aimed at developing a robust creative and business environment that allows to convert technological breakthroughs to new markets into an element of the system of continuous reproduction of income, human and technological capital. Information base of the research includes legal documents of the Government of the Russian Federation, the official publications under the project office of STI, reports of Russian Academy of Sciences, developments of the Expert Council under the government of the Russian Federation and Agency for strategic initiatives, Federal Agency of scientific organizations, research groups, individual scientists and specialists, Internet resources and the authors’ own developments. The first systematic and methodologically coherent statement of the ideology of economy transformation in the conditions of forming national technological initiative is presented in the report “Framework of the National technology initiative” of

  17. Rescattering effects on intensity interferometry and initial conditions in relativistic heavy ion collisions

    Science.gov (United States)

    Li, Yang

    The properties of the quark-gluon plasma are being thoroughly studied by utilizing relativistic heavy ion collisions. After its invention in astronomy in the 1950s, intensity interferometry was found to be a robust method to probe the spatial and temporal information of the nuclear collisions also. Although rescattering effects are negligible in elementary particle collisions, it may be very important for heavy ion collisions at RHIC and in the future LHC. Rescattering after production will modify the measured correlation function and make it harder to extract the dynamical information from data. To better understand the data which are dimmed by this final state process, we derive a general formula for intensity interferometry which can calculate rescattering effects easily. The formula can be used both non-relativistically and relativistically. Numerically, we found that rescattering effects on kaon interferometry for RHIC experiments can modify the measured ratio of the outward radius to the sideward radius, which is a sensitive probe to the equation of state, by as large as 15%. It is a nontrivial contribution which should be included to understand the data more accurately. The second part of this thesis is on the initial conditions in relativistic heavy ion collisions. Although relativistic hydrodynamics is successful in explaining many aspects of the data, it is only valid after some finite time after nuclear contact. The results depend on the choice of initial conditions which, so far, have been very uncertain. I describe a formula based on the McLerran-Venugopalan model to compute the initial energy density. The soft gluon fields produced immediately after the overlap of the nuclei can be expanded as a power series of the proper time t. Solving Yang-Mills equations with color current conservation can give us the analytical formulas for the fields. The local color charges on the transverse plane are stochastic variables and have to be taken care of by random

  18. Carbon allocation to major metabolites in illuminated leaves is not just proportional to photosynthesis when gaseous conditions (CO2 and O2 ) vary.

    Science.gov (United States)

    Abadie, Cyril; Bathellier, Camille; Tcherkez, Guillaume

    2018-04-01

    In gas-exchange experiments, manipulating CO 2 and O 2 is commonly used to change the balance between carboxylation and oxygenation. Downstream metabolism (utilization of photosynthetic and photorespiratory products) may also be affected by gaseous conditions but this is not well documented. Here, we took advantage of sunflower as a model species, which accumulates chlorogenate in addition to sugars and amino acids (glutamate, alanine, glycine and serine). We performed isotopic labelling with 13 CO 2 under different CO 2 /O 2 conditions, and determined 13 C contents to compute 13 C-allocation patterns and build-up rates. The 13 C content in major metabolites was not found to be a constant proportion of net fixed carbon but, rather, changed dramatically with CO 2 and O 2 . Alanine typically accumulated at low O 2 (hypoxic response) while photorespiratory intermediates accumulated under ambient conditions and at high photorespiration, glycerate accumulation exceeding serine and glycine build-up. Chlorogenate synthesis was relatively more important under normal conditions and at high CO 2 and its synthesis was driven by phosphoenolpyruvate de novo synthesis. These findings demonstrate that carbon allocation to metabolites other than photosynthetic end products is affected by gaseous conditions and therefore the photosynthetic yield of net nitrogen assimilation varies, being minimal at high CO 2 and maximal at high O 2 . © 2018 The Authors. New Phytologist © 2018 New Phytologist Trust.

  19. Optimization of hydrostatic pressure at varied sonication conditions--power density, intensity, very low frequency--for isothermal ultrasonic sludge treatment.

    Science.gov (United States)

    Delmas, Henri; Le, Ngoc Tuan; Barthe, Laurie; Julcour-Lebigue, Carine

    2015-07-01

    This work aims at investigating for the first time the key sonication (US) parameters: power density (DUS), intensity (IUS), and frequency (FS) - down to audible range, under varied hydrostatic pressure (Ph) and low temperature isothermal conditions (to avoid any thermal effect). The selected application was activated sludge disintegration, a major industrial US process. For a rational approach all comparisons were made at same specific energy input (ES, US energy per solid weight) which is also the relevant economic criterion. The decoupling of power density and intensity was obtained by either changing the sludge volume or most often by changing probe diameter, all other characteristics being unchanged. Comprehensive results were obtained by varying the hydrostatic pressure at given power density and intensity. In all cases marked maxima of sludge disintegration appeared at optimum pressures, which values increased at increasing power intensity and density. Such optimum was expected due to opposite effects of increasing hydrostatic pressure: higher cavitation threshold then smaller and fewer bubbles, but higher temperature and pressure at the end of collapse. In addition the first attempt to lower US frequency down to audible range was very successful: at any operation condition (DUS, IUS, Ph, sludge concentration and type) higher sludge disintegration was obtained at 12 kHz than at 20 kHz. The same values of optimum pressure were observed at 12 and 20 kHz. At same energy consumption the best conditions - obtained at 12 kHz, maximum power density 720 W/L and 3.25 bar - provided about 100% improvement with respect to usual conditions (1 bar, 20 kHz). Important energy savings and equipment size reduction may then be expected. Copyright © 2014 Elsevier B.V. All rights reserved.

  20. A simple method to calculate first-passage time densities with arbitrary initial conditions

    Science.gov (United States)

    Nyberg, Markus; Ambjörnsson, Tobias; Lizana, Ludvig

    2016-06-01

    Numerous applications all the way from biology and physics to economics depend on the density of first crossings over a boundary. Motivated by the lack of general purpose analytical tools for computing first-passage time densities (FPTDs) for complex problems, we propose a new simple method based on the independent interval approximation (IIA). We generalise previous formulations of the IIA to include arbitrary initial conditions as well as to deal with discrete time and non-smooth continuous time processes. We derive a closed form expression for the FPTD in z and Laplace-transform space to a boundary in one dimension. Two classes of problems are analysed in detail: discrete time symmetric random walks (Markovian) and continuous time Gaussian stationary processes (Markovian and non-Markovian). Our results are in good agreement with Langevin dynamics simulations.

  1. On the initial condition problem of the time domain PMCHWT surface integral equation

    KAUST Repository

    Uysal, Ismail Enes

    2017-05-13

    Non-physical, linearly increasing and constant current components are induced in marching on-in-time solution of time domain surface integral equations when initial conditions on time derivatives of (unknown) equivalent currents are not enforced properly. This problem can be remedied by solving the time integral of the surface integral for auxiliary currents that are defined to be the time derivatives of the equivalent currents. Then the equivalent currents are obtained by numerically differentiating the auxiliary ones. In this work, this approach is applied to the marching on-in-time solution of the time domain Poggio-Miller-Chan-Harrington-Wu-Tsai surface integral equation enforced on dispersive/plasmonic scatterers. Accuracy of the proposed method is demonstrated by a numerical example.

  2. Corrosion study of API 5L x-series pipeline steels in 3.5% NaCl solution under varying conditions

    International Nuclear Information System (INIS)

    Shahid, M.; Qureshi, M.I.; Farooq, M.U.; Khan, M.I.

    2003-01-01

    Pipelines provide convenient and efficient means for mass transportation of variety of fluids, such as oil and gas, over varying distances. In the last two decades or so, pipeline designers focused mainly on the usage of larger sizes and higher operating pressures for achieving higher transportation efficiency. This has been accomplished through the provision of steels with progressive increase in yield strength coupled with good weldability and sufficient toughness to restrict crack propagation. In addition to higher strength and toughness, developing pipeline technologies have required improved resistance to corrosion, which has been tried with specific alloy additions and special control over non-metallic inclusions. Corrosion investigations were carried out on various grades of pipeline steels (API 5L X-46, X-52, X-56, X-60 and X- 70) under varying environmental conditions. This paper describes the results pertaining to corrosion behavior of the steels in 3.5% NaCl solutions in stagnant, turbulent and deaerated conditions. It was found that all grades corrode in this solution and their corrosion potentials and corrosion currents are in close vicinity of each other. Turbulent solutions, however, have shown an increase in corrosion rates whereas deaeration has revealed a relative decrease in aggressivity of the electrolyte. (author)

  3. RECREATION MONITORING OF RESOURCE CONDITIONS IN THE KRONOTSKY STATE NATURAL BIOSPHERE PRESERVE (KAMCHATKA: AN INITIAL ASSESSMENT

    Directory of Open Access Journals (Sweden)

    Anna Zavadskaya

    2011-01-01

    Full Text Available The paper describes assessment and monitoring program which has been designed and initiated for monitoring recreational impacts in some wildernesses areas of Kamchatka. The framework of the recreational assessment was tested through its application in a case study conducted during the summer 2008 in the Kronotsky State Natural Biosphere Preserve (the Kamchatka peninsula, Russia. The overall objective of the case study was to assess the existing campsite and trail recreation impacts and to establish a network of key sites for the subsequent long-term impact monitoring. The detailed assessment of different components of natural complexes of the Kronotsky State Natural Preserve and the obtained maps of their ecological conditions showed that some sites had been highly disturbed. The results of these works have given rise to a concern that the intensive use of these areas would make an unacceptable impact on the nature. Findings of our initial work corroborate the importance of founding wilderness management programs on knowledge about the trail and campsite impacts and emphasize the necessity of adopting the recreational assessment and monitoring framework to the practice of decision-making.

  4. Height distribution tails in the Kardar-Parisi-Zhang equation with Brownian initial conditions

    Science.gov (United States)

    Meerson, Baruch; Schmidt, Johannes

    2017-10-01

    For stationary interface growth, governed by the Kardar-Parisi-Zhang (KPZ) equation in 1 + 1 dimensions, typical fluctuations of the interface height at long times are described by the Baik-Rains distribution. Recently Chhita et al (2016 arXiv:1611.06690) used the totally asymmetric simple exclusion process (TASEP) to study the height fluctuations in systems of the KPZ universality class for Brownian interfaces with arbitrary diffusion constant. They showed that there is a one-parameter family of long-time distributions, parameterized by the diffusion constant of the initial random height profile. They also computed these distributions numerically by using Monte Carlo (MC) simulations. Here we address this problem analytically and focus on the distribution tails at short times. We determine the (stretched exponential) tails of the height distribution by applying the optimal fluctuation method (OFM) to the KPZ equation. We argue that, by analogy with other initial conditions, the ‘slow’ tail holds at arbitrary times and therefore provides a proper asymptotic to the family of long-time distributions studied in Chhita et al (2016 arXiv:1611.06690). We verify this hypothesis by performing large-scale MC simulations of a TASEP with a parallel-update rule. The ‘fast’ tail, predicted by the OFM, is also expected to hold at arbitrary times, at sufficiently large heights.

  5. Tribological and Wear Performance of Carbide Tools with TiB2 PVD Coating under Varying Machining Conditions of TiAl6V4 Aerospace Alloy

    Directory of Open Access Journals (Sweden)

    Jose Mario Paiva

    2017-11-01

    Full Text Available Tribological phenomena and tool wear mechanisms during machining of hard-to-cut TiAl6V4 aerospace alloy have been investigated in detail. Since cutting tool wear is directly affected by tribological phenomena occurring between the surfaces of the workpiece and the cutting tool, the performance of the cutting tool is strongly associated with the conditions of the machining process. The present work shows the effect of different machining conditions on the tribological and wear performance of TiB2-coated cutting tools compared to uncoated carbide tools. FEM modeling of the temperature profile on the friction surface was performed for wet machining conditions under varying cutting parameters. Comprehensive characterization of the TiB2 coated vs. uncoated cutting tool wear performance was made using optical 3D imaging, SEM/EDX and XPS methods respectively. The results obtained were linked to the FEM modeling. The studies carried out show that during machining of the TiAl6V4 alloy, the efficiency of the TiB2 coating application for carbide cutting tools strongly depends on cutting conditions. The TiB2 coating is very efficient under roughing at low speeds (with strong buildup edge formation. In contrast, it shows similar wear performance to the uncoated tool under finishing operations at higher cutting speeds when cratering wear predominates.

  6. Automatic Traffic Data Collection under Varying Lighting and Temperature Conditions in Multimodal Environments: Thermal versus Visible Spectrum Video-Based Systems

    Directory of Open Access Journals (Sweden)

    Ting Fu

    2017-01-01

    Full Text Available Vision-based monitoring systems using visible spectrum (regular video cameras can complement or substitute conventional sensors and provide rich positional and classification data. Although new camera technologies, including thermal video sensors, may improve the performance of digital video-based sensors, their performance under various conditions has rarely been evaluated at multimodal facilities. The purpose of this research is to integrate existing computer vision methods for automated data collection and evaluate the detection, classification, and speed measurement performance of thermal video sensors under varying lighting and temperature conditions. Thermal and regular video data was collected simultaneously under different conditions across multiple sites. Although the regular video sensor narrowly outperformed the thermal sensor during daytime, the performance of the thermal sensor is significantly better for low visibility and shadow conditions, particularly for pedestrians and cyclists. Retraining the algorithm on thermal data yielded an improvement in the global accuracy of 48%. Thermal speed measurements were consistently more accurate than for the regular video at daytime and nighttime. Thermal video is insensitive to lighting interference and pavement temperature, solves issues associated with visible light cameras for traffic data collection, and offers other benefits such as privacy, insensitivity to glare, storage space, and lower processing requirements.

  7. A study on gap heat transfer of LWR fuel rods under reactivity initiated accident conditions

    International Nuclear Information System (INIS)

    Fujishiro, Toshio

    1984-03-01

    Gap heat transfer between fuel pellet and cladding have a large influence on the LWR fuel behaviors under reactivity initiated accident (RIA) conditions. The objective of the present study is to investigate the effects of gap heat transfer on RIA fuel behaviors based on the results of the gap-gas parameter tests in NSRR and on their analysis with NSR-77 code. Through this study, transient variations of gap heat transfer, the effects of the gap heat transfer on fuel thermal behaviors and on fuel failure, effects of pellet-cladding sticking by eutectic formation, and the effects of cladding collapse under high external pressure have been clearified. The studies have also been performed on the applicability and its limit of modified Ross and Stoute equation which is extensively utilized to evaluate the gap heat transfer coefficient in the present fuel behavior codes. The method to evaluate the gap conductance to the conditions beyond the applicability limit of the Ross and Stoute equation has also been proposed. (author)

  8. Hydrological modelling for flood forecasting: Calibrating the post-fire initial conditions

    Science.gov (United States)

    Papathanasiou, C.; Makropoulos, C.; Mimikou, M.

    2015-10-01

    Floods and forest fires are two of the most devastating natural hazards with severe socioeconomic, environmental as well as aesthetic impacts on the affected areas. Traditionally, these hazards are examined from different perspectives and are thus investigated through different, independent systems, overlooking the fact that they are tightly interrelated phenomena. In fact, the same flood event is more severe, i.e. associated with increased runoff discharge and peak flow and decreased time to peak, if it occurs over a burnt area than that occurring over a land not affected by fire. Mediterranean periurban areas, where forests covered with flammable vegetation coexist with agricultural land and urban zones, are typical areas particularly prone to the combined impact of floods and forest fires. Hence, the accurate assessment and effective management of post-fire flood risk becomes an issue of priority. The research presented in this paper aims to develop a robust methodological framework, using state of art tools and modern technologies to support the estimation of the change in time of five representative hydrological parameters for post-fire conditions. The proposed methodology considers both longer- and short-term initial conditions in order to assess the dynamic evolution of the selected parameters. The research focuses on typical Mediterranean periurban areas that are subjected to both hazards and concludes with a set of equations that associate post-fire and pre-fire conditions for five Fire Severity (FS) classes and three soil moisture states. The methodology has been tested for several flood events on the Rafina catchment, a periurban catchment in Eastern Attica (Greece). In order to validate the methodology, simulated hydrographs were produced and compared against available observed data. Results indicate a close convergence of observed and simulated flows. The proposed methodology is particularly flexible and thus easily adaptable to catchments with similar

  9. Vasculogenesis and angiogenesis initiation under normoxic conditions through Wnt/β-catenin pathway in gliomas.

    Science.gov (United States)

    Vallée, Alexandre; Guillevin, Rémy; Vallée, Jean-Noël

    2018-01-26

    The canonical Wnt/β-catenin pathway is up-regulated in gliomas and involved in proliferation, invasion, apoptosis, vasculogenesis and angiogenesis. Nuclear β-catenin accumulation correlates with malignancy. Hypoxia activates hypoxia-inducible factor (HIF)-1α by inhibiting HIF-1α prolyl hydroxylation, which promotes glycolytic energy metabolism, vasculogenesis and angiogenesis, whereas HIF-1α is degraded by the HIF prolyl hydroxylase under normoxic conditions. We focus this review on the links between the activated Wnt/β-catenin pathway and the mechanisms underlying vasculogenesis and angiogenesis through HIF-1α under normoxic conditions in gliomas. Wnt-induced epidermal growth factor receptor/phosphatidylinositol 3-kinase (PI3K)/Akt signaling, Wnt-induced signal transducers and activators of transcription 3 (STAT3) signaling, and Wnt/β-catenin target gene transduction (c-Myc) can activate HIF-1α in a hypoxia-independent manner. The PI3K/Akt/mammalian target of rapamycin pathway activates HIF-1α through eukaryotic translation initiation factor 4E-binding protein 1 and STAT3. The β-catenin/T-cell factor 4 complex directly binds to STAT3 and activates HIF-1α, which up-regulates the Wnt/β-catenin target genes cyclin D1 and c-Myc in a positive feedback loop. Phosphorylated STAT3 by interleukin-6 or leukemia inhibitory factor activates HIF-1α even under normoxic conditions. The activation of the Wnt/β-catenin pathway induces, via the Wnt target genes c-Myc and cyclin D1 or via HIF-1α, gene transactivation encoding aerobic glycolysis enzymes, such as glucose transporter, hexokinase 2, pyruvate kinase M2, pyruvate dehydrogenase kinase 1 and lactate dehydrogenase-A, leading to lactate production, as the primary alternative of ATP, at all oxygen levels, even in normoxic conditions. Lactate released by glioma cells via the monocarboxylate lactate transporter-1 up-regulated by HIF-1α and lactate anion activates HIF-1α in normoxic endothelial cells by

  10. The effect of bedload transport rates on bedform and planform morphological development in a laboratory meandering stream under varying flow conditions

    Science.gov (United States)

    Sullivan, C.; Good, R. G. R.; Binns, A. D.

    2017-12-01

    Sediment transport processes in streams provides valuable insight into the temporal evolution of planform and bedform geometry. The majority of previous experimental research in the literature has focused on bedload transport and corresponding bedform development in rectangular, confined channels, which does not consider planform adjustment processes in streams. In contrast, research conducted with laboratory streams having movable banks can investigate planform development in addition to bedform development, which is more representative of natural streams. The goal of this research is to explore the relationship between bedload transport rates and the morphological adjustments in meandering streams. To accomplish this, a series of experimental runs were conducted in a 5.6 m by 1.9 m river basin flume at the University of Guelph to analyze the bedload impacts on bed formations and planform adjustments in response to varying flow conditions. In total, three experimental runs were conducted: two runs using steady state conditions and one run using unsteady flow conditions in the form of a symmetrical hydrograph implementing quasi steady state flow. The runs were performed in a series of time-steps in order to monitor the evolution of the stream morphology and the bedload transport rates. Structure from motion (SfM) was utilized to capture the channel morphology after each time-step, and Agisoft PhotoScan software was used to produce digital elevation models to analyze the morphological evolution of the channel with time. Bedload transport rates were quantified using a sediment catch at the end of the flume. Although total flow volumes were similar for each run, the morphological evolution and bedload transport rates in each run varied. The observed bedload transport rates from the flume are compared with existing bedload transport formulas to assess their accuracy with respect to sediment transport in unconfined meandering channels. The measured sediment transport

  11. Reconstruction of Oryza sativa indica Genome Scale Metabolic Model and Its Responses to Varying RuBisCO Activity, Light Intensity, and Enzymatic Cost Conditions

    Directory of Open Access Journals (Sweden)

    Ankita Chatterjee

    2017-11-01

    Full Text Available To combat decrease in rice productivity under different stresses, an understanding of rice metabolism is needed. Though there are different genome scale metabolic models (GSMs of Oryza sativa japonica, no GSM with gene-protein-reaction association exist for Oryza sativa indica. Here, we report a GSM, OSI1136 of O.s. indica, which includes 3602 genes and 1136 metabolic reactions and transporters distributed across the cytosol, mitochondrion, peroxisome, and chloroplast compartments. Flux balance analysis of the model showed that for varying RuBisCO activity (Vc/Vo (i the activity of the chloroplastic malate valve increases to transport reducing equivalents out of the chloroplast under increased photorespiratory conditions and (ii glyceraldehyde-3-phosphate dehydrogenase and phosphoglycerate kinase can act as source of cytosolic ATP under decreased photorespiration. Under increasing light conditions we observed metabolic flexibility, involving photorespiration, chloroplastic triose phosphate and the dicarboxylate transporters of the chloroplast and mitochondrion for redox and ATP exchanges across the intracellular compartments. Simulations under different enzymatic cost conditions revealed (i participation of peroxisomal glutathione-ascorbate cycle in photorespiratory H2O2 metabolism (ii different modes of the chloroplastic triose phosphate transporters and malate valve, and (iii two possible modes of chloroplastic Glu–Gln transporter which were related with the activity of chloroplastic and cytosolic isoforms of glutamine synthetase. Altogether, our results provide new insights into plant metabolism.

  12. Constraints on rapidity-dependent initial conditions from charged-particle pseudorapidity densities and two-particle correlations

    Science.gov (United States)

    Ke, Weiyao; Moreland, J. Scott; Bernhard, Jonah E.; Bass, Steffen A.

    2017-10-01

    We study the initial three-dimensional spatial configuration of the quark-gluon plasma (QGP) produced in relativistic heavy-ion collisions using centrality and pseudorapidity-dependent measurements of the medium's charged particle density and two-particle correlations. A cumulant-generating function is first used to parametrize the rapidity dependence of local entropy deposition and extend arbitrary boost-invariant initial conditions to nonzero beam rapidities. The model is then compared to p +Pb and Pb + Pb charged-particle pseudorapidity densities and two-particle pseudorapidity correlations and systematically optimized using Bayesian parameter estimation to extract high-probability initial condition parameters. The optimized initial conditions are then compared to a number of experimental observables including the pseudorapidity-dependent anisotropic flows, event-plane decorrelations, and flow correlations. We find that the form of the initial local longitudinal entropy profile is well constrained by these experimental measurements.

  13. Condition Help: A Patient- and Family-Initiated Rapid Response System.

    Science.gov (United States)

    Eden, Elizabeth L; Rack, Laurie L; Chen, Ling-Wan; Bump, Gregory M

    2017-03-01

    Rapid response teams (RRTs) help in delivering safe, timely care. Typically they are activated by clinicians using specific parameters. Allowing patients and families to activate RRTs is a novel intervention. The University of Pittsburgh Medical Center developed and implemented a patient- and family-initiated rapid response system called Condition Help (CH). When the CH system is activated, a patient care liaison or an on-duty administrator meets bedside with the unit charge nurse to address the patient's concerns. In this study, we collected demographic data, call reasons, call designations (safety or nonsafety), and outcome information for all CH calls made during the period January 2012 through June 2015. Two hundred forty patients/family members made 367 CH calls during the study period. Most calls were made by patients (76.8%) rather than family members (21.8%). Of the 240 patients, 43 (18%) made multiple calls; their calls accounted for 46.3% of all calls (170/367). Inadequate pain control was the reason for the call in most cases (48.2%), followed by dissatisfaction with staff (12.5%). The majority of calls involved nonsafety issues (83.4%) rather than safety issues (11.4%). In 41.4% of cases, a change in care was made. Patient- and family-initiated RRTs are designed to engage patients and families in providing safer care. In the CH system, safety issues are identified, but the majority of calls involve nonsafety issues. Journal of Hospital Medicine 2017;12:157-161. © 2017 Society of Hospital Medicine

  14. Differences in nutrient uptake capacity of the benthic filamentous algae Cladophora sp., Klebsormidium sp. and Pseudanabaena sp. under varying N/P conditions.

    Science.gov (United States)

    Liu, Junzhuo; Vyverman, Wim

    2015-03-01

    The N/P ratio of wastewater can vary greatly and directly affect algal growth and nutrient removal process. Three benthic filamentous algae species Cladophora sp., Klebsormidium sp. and Pseudanabaena sp. were isolated from a periphyton bioreactor and cultured under laboratory conditions on varying N/P ratios to determine their ability to remove nitrate and phosphorus. The N/P ratio significantly influenced the algal growth and phosphorus uptake process. Appropriate N/P ratios for nitrogen and phosphorus removal were 5-15, 7-10 and 7-20 for Cladophora sp., Klebsormidium sp. and Pseudanabaena sp., respectively. Within these respective ranges, Cladophora sp. had the highest biomass production, while Pseudanabaena sp. had the highest nitrogen and phosphorus contents. This study indicated that Cladophora sp. had a high capacity of removing phosphorus from wastewaters of low N/P ratio, and Pseudanabaena sp. was highly suitable for removing nitrogen from wastewaters with high N/P ratio. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. Determination and demarcation of fatigue crack initiation phase in rotating bending condition

    International Nuclear Information System (INIS)

    Pasha, R.A.; Rehman, K.; Shah, M.

    2012-01-01

    In engineering applications, components often experience cyclic loading and therefore, have crack initiation propagation phase. In this research work experimental demarcation of fatigue crack initiation has been investigated. Initiation phase of fatigue life of Aluminium was determined by using single and two step fatigue loading test on four point rotating bending fatigue testing machine. Experimental data is used to determine the distinction between the initiation and propagation phase. Initiation phase is determined at different stress levels. The obtained results demonstrate the effect of stress level on initiation phase and propagation phase. (author)

  16. Study on the behavior of waterside corroded PWR fuel rods under reactivity initiated accident conditions

    International Nuclear Information System (INIS)

    Sasajima, Hideo

    1989-06-01

    One of the highlighted problems from the fuel reliability point of view is a waterside corrosion of fuel cladding which becomes more significant at extended burnup stages. To date, at highly burned fuel, waterside corrosion was recognized as important because cladding oxidation increased with increasing burn-up. In experiments, as the basic research for the study of high burn-up fuel, the test fuel rods were prepressurized to ranges from 3.47 to 3.55 MPa, oxidized artificially to both 10 and 20 μm in thickness. Regarding fabricated oxide thickness of 10 μm, it is corresponded to be transition point from cubic law to linear law as a function of burn-up. Pulse irradiation experiments by NSRR were carried out to study the behavior of waterside corroded PWR type fuels under RIA conditions. Obtained results are: (1) The failure threshold of tested fuels was 110 cal/g·fuel (0.46 KJ/g·fuel) in enthalpy. This showed that the failure threshold of tested fuels was same as that of the past NSRR experimental data. (2) The failure mechanisms of the tested fuel rods was cladding rupture induced by ballooning. No differences in failure mechanisms existed between the past NSRR prepressurized standard fuel and the tested fuels. (3) Cracks were existed without propagating into cladding matrix, so that it was judged that these were not initiation of failure. (4) Whithin this experimental condition, reduction of cladding thickness being attributed to the increase of oxidation did not failure threshold. (author)

  17. High burnup (41 - 61 GWd/tU) BWR fuel behavior under reactivity initiated accident conditions

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, Takehiko; Kusagaya, Kazuyuki; Yoshinaga, Makio; Uetsuka, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-12-01

    High burnup boiling water reactor (BWR) fuel was pulse irradiated in the Nuclear Safety Research Reactor (NSRR) to investigate fuel behavior under cold startup reactivity initiated accident (RIA) conditions. Temperature, deformation, failure, and fission gas release behavior under the simulated RIA condition was studied in the tests. Fuel failure due to pellet-cladding mechanical interaction (PCMI) did not occur in the tests with typical domestic BWR fuel at burnups up to 56 GWd/tU, because they had limited cladding embrittlement due to hydrogen absorption of about 100 ppm or less. However, the cladding failure occurred in tests with fuel at a burnup of 61 GWd/tU, in which the peak hydrogen content in the cladding was above 150 ppm. This type of failure was observed for the first time in BWR fuels. The cladding failure occurred at fuel enthalpies of 260 to 360 J/g (62 to 86 cal/g), which were higher than the PCMI failure thresholds decided by the Japanese Nuclear Safety Commission. From post-test examinations of the failed fuel, it was found that the crack in the BWR cladding progressed in a manner different from the one in PWR cladding failed in earlier tests, owing to its more randomly oriented hydride distribution. Because of these differences, the BWR fuel was judged to have failed at hydrogen contents lower than those of the PWR fuel. Comparison of the test results with code calculations revealed that the PCMI failure was caused by thermal expansion of pellets, rather than by the fission gas expansion in the pellets. The gas expansion, however, was found to cause large cladding hoop deformation later after the cladding temperature escalated. (author)

  18. Behavior of irradiated ATR/MOX fuel under reactivity initiated accident conditions (Joint research)

    International Nuclear Information System (INIS)

    Sasajima, Hideo; Fuketa, Toyoshi; Nakamura, Takehiko; Nakamura, Jinichi; Uetsuka, Hiroshi

    2000-03-01

    Pulse irradiation experiments with irradiated ATR/MOX fuel rods of 20 MWd/kgHM were conducted at the NSRR in JAERI to study the transient behavior of MOX fuel rod under reactivity initiated accident conditions. Four pulse irradiation experiments were performed with peak fuel enthalpy ranging from 335 J/g to 586 J/g, resulted in no failure of fuel rods. Deformation of the fuel rods due to PCMI occurred in the experiments with peak fuel enthalpy above 500 J/g. Significant fission gas release up to 20% was measured by rod puncture measurement. The generation of fine radial cracks in pellet periphery, micro-cracks and boundary separation over the entire region of pellet were observed. These microstructure changes might contribute to the swelling of fuel pellets during the pulse irradiation. This could cause the large radial deformation of fuel rod and high fission gas release when the pulse irradiation conducted at relatively high peak fuel enthalpy. In addition, fine grain structures around the plutonium spot and cauliflower structure in cavity of the plutonium spot were observed in the outer region of the fuel pellet. (author)

  19. Topology in two dimensions. IV - CDM models with non-Gaussian initial conditions

    Science.gov (United States)

    Coles, Peter; Moscardini, Lauro; Plionis, Manolis; Lucchin, Francesco; Matarrese, Sabino; Messina, Antonio

    1993-02-01

    The results of N-body simulations with both Gaussian and non-Gaussian initial conditions are used here to generate projected galaxy catalogs with the same selection criteria as the Shane-Wirtanen counts of galaxies. The Euler-Poincare characteristic is used to compare the statistical nature of the projected galaxy clustering in these simulated data sets with that of the observed galaxy catalog. All the models produce a topology dominated by a meatball shift when normalized to the known small-scale clustering properties of galaxies. Models characterized by a positive skewness of the distribution of primordial density perturbations are inconsistent with the Lick data, suggesting problems in reconciling models based on cosmic textures with observations. Gaussian CDM models fit the distribution of cell counts only if they have a rather high normalization but possess too low a coherence length compared with the Lick counts. This suggests that a CDM model with extra large scale power would probably fit the available data.

  20. Slum Conditions in Haryana and Pro-poor Housing Initiatives in Faridabad, India

    Directory of Open Access Journals (Sweden)

    Nirmala

    2017-09-01

    Full Text Available Rapid urbanization forces urban poor to live in slums and squatter settlement. In neo-liberal development approach, participatory planning and collaborative actions are becoming popular in slum upgrading programmes. This paper discusses the slum scenario in state of Haryana along with detailed pro-poor housing attempts in industrial city of Haryana i.e. Faridabad. The paper reviews the three projects that aimed to improve the living conditions and lives of urban poor communities in Faridabad. The study examines in detail BSUP projects at Dabua Colony and Bapu Nagar taken up under India’s first urban renewal mission i.e. JNNURM within the context of community participation. Results reveal that contrary to the state’s rhetoric of inclusive governance, the urban poor are completely excluded from settlement planning, leading to a lack of understanding of their needs by the state. BSUP housing scheme has failed to mobilize slum dwellers. Drawing on the experience of these projects, the paper seeks to answer the question: why the stated objectives were not achieved and makes recommendation that community led initiatives and slum mapping should be at the core of slum improvement strategy so that qualitatively superior areas can be planned for the unprivileged.

  1. Behaviour of rock-like oxide fuels under reactivity-initiated accident conditions

    International Nuclear Information System (INIS)

    Kazuyuki, Kusagaya; Takehiko, Nakamura; Makio, Yoshinaga; Hiroshi, Akie; Toshiyuki, Yamashita; Hiroshi, Uetsuka

    2002-01-01

    Pulse irradiation tests of three types of un-irradiated rock-like oxide (ROX) fuel - yttria-stabilised zirconia (YSZ) single phase, YSZ and spinel (MgAl 2 O 4 ) homogeneous mixture and particle-dispersed YSZ/spinel - were conducted in the Nuclear Safety Research Reactor to investigate the fuel behaviour under reactivity-initiated accident conditions. The ROX fuels failed at fuel volumetric enthalpies above 10 GJ/m 3 , which was comparable to that of un-irradiated UO 2 fuel. The failure mode of the ROX fuels, however, was quite different from that of the UO 2 fuel. The ROX fuels failed with fuel pellet melting and a part of the molten fuel was released out to the surrounding coolant water. In spite of the release, no significant mechanical energy generation due to fuel/coolant thermal interaction was observed in the tested enthalpy range below∼12 GJ/m 3 . The YSZ type and homogenous YSZ/spinel type ROX fuels failed by cladding burst when their temperatures peaked, while the particle-dispersed YSZ/spinel type ROX fuel seemed to have failed by cladding local melting. (author)

  2. Quantum reversibility is relative, or does a quantum measurement reset initial conditions?

    Science.gov (United States)

    Zurek, Wojciech H

    2018-07-13

    I compare the role of the information in classical and quantum dynamics by examining the relation between information flows in measurements and the ability of observers to reverse evolutions. I show that in the Newtonian dynamics reversibility is unaffected by the observer's retention of the information about the measurement outcome. By contrast-even though quantum dynamics is unitary, hence, reversible-reversing quantum evolution that led to a measurement becomes, in principle, impossible for an observer who keeps the record of its outcome. Thus, quantum irreversibility can result from the information gain rather than just its loss-rather than just an increase of the (von Neumann) entropy. Recording of the outcome of the measurement resets, in effect, initial conditions within the observer's (branch of) the Universe. Nevertheless, I also show that the observer's friend-an agent who knows what measurement was successfully carried out and can confirm that the observer knows the outcome but resists his curiosity and does not find out the result-can, in principle, undo the measurement. This relativity of quantum reversibility sheds new light on the origin of the arrow of time and elucidates the role of information in classical and quantum physics. Quantum discord appears as a natural measure of the extent to which dissemination of information about the outcome affects the ability to reverse the measurement.This article is part of a discussion meeting issue 'Foundations of quantum mechanics and their impact on contemporary society'. © 2018 The Author(s).

  3. The influence of initial conditions of water-entry on ricochet phenomenon

    Energy Technology Data Exchange (ETDEWEB)

    Guoming, Chen; Jinfu, Feng; Junhua, Hu; An, Liu [Aeronautics and Astronautics Engineering College, Air Force Engineering University, Xi’an, 710038 (China); Yongli, Li, E-mail: 18192081790@163.com [Engineering University of CAPF, Xi’an 710086 (China)

    2017-08-15

    The ricochet phenomenon of the water-entry of the water–air crossing vehicle is investigated by both experiments and numerical simulations. Experiments and numerical simulations of the water-entry process with different inclination angles, velocities, and attack angles are performed. The whole ricochet progress and the changing rules of angular acceleration, angular velocity, and displacement are obtained and analyzed by numerical simulation for a deeper understanding of ricochet phenomenon. The experiment is carried out to study the underwater trajectory by changing the initial condition only. The experimental results are in good agreement with the simulations. The results show that: (1) A small inclination angle causes the trajectory to bend upward, favoring the ricochet phenomenon. (2) A large velocity value also favors the ricochet phenomenon, making it occur more easily and quickly, but lower velocities are insufficient to provide the necessary kinetic energy. (3) The ricochet phenomenon is more likely to occur under a negative attack angle that causes the trajectory to bend upward, but a positive angle balances the underwater trajectory. These results can provide guidance to design a new water–air cross vehicle. (paper)

  4. Initial sexual maturity and fecundity of the goldfish Carassius auratus (Perciformes: Cyprynidae under semi-controlled conditions

    Directory of Open Access Journals (Sweden)

    A.A Ortega-Salas

    2006-12-01

    Full Text Available We studied the time of initial sexual maturity and the fecundity of the goldfish Carassius auratus under semi-controlled conditions. During the study the water temperature fluctuated from 21 to 30 ºC, the pH between 7 and 8, and the dissolved oxygen between 5.5 and 7 ppm. Sixty days old juvenile fish received prophylactic treatments of brackish water (15 ‰ and methylene blue baths (1 %, and they were fed with live Daphnia magna. The initial sexual maturity occurred between 225 and 233 days of captivity. Mean absolute fecundity was 2 347 (± 302.2 SD ova per gonad, and mean relative fecundity was 63.44 eggs/g fish weight. Gonadosomatic index was between 7.5 and 9.0. Our data will allow ornamental fish producers to calculate the time of initial maturity and fecundity for this species. Rev. Biol. Trop. 54 (4: 1113-1116. Epub 2006 Dec. 15.Estudiamos el tiempo inicial de madurez sexual y la fecundidad del pez dorado Carassius auratus en condiciones semi-controladas. Durante el estudio la temperatura del gua varió de 21 a 30 ºC, el pH entre 7 y 8, y el oxígeno disuelto entre 5.5 y 7 ppm. Jóvenes de 60 días de edad recibieron tratamiento profiláctico con agua salobre (15 ‰, y baños de azul de metileno (1 %. Se les alimentó con Daphnia magna. La madurez sexual inicial fue tras 225 a 233 días en cautiverio. La fecundidad absoluta media fue de 2 347 (±302.2 DS óvulos por gónada y la fecundidad relativa fue de 63.44 óvulos/g del peso del pez. El índice gonadosomático se calculó entre 7.5 and 9.0.

  5. A method comparison of total and HMW adiponectin: HMW/total adiponectin ratio varies versus total adiponectin, independent of clinical condition.

    Science.gov (United States)

    van Andel, Merel; Drent, Madeleine L; van Herwaarden, Antonius E; Ackermans, Mariëtte T; Heijboer, Annemieke C

    2017-02-01

    Total and high-molecular-weight (HMW) adiponectin have been associated with endocrine and cardiovascular pathology. As no gold standard is available, the discussion about biological relevance of isoforms is complicated. In our study we perform a method comparison between two commercially available assays measuring HMW and total adiponectin, in various patient groups, thus contributing further to this discussion. We determined levels of HMW and total adiponectin using assays by Lumipulse® and Millipore® respectively, in 126 patients with different clinical characteristics (n=29 healthy volunteers, n=22 dialysis patients, n=25 elderly with body mass index (BMI) LUMIPULSE ∗0.5-0.9=total adiponectin MILLIPORE , albeit with significant deviation from linearity (p<0.001). Pearson's correlation was R=0.987 (p=0.000). No significant differences between patient groups were observed (p=0.190). The HMW/total adiponectin ratio varies with total adiponectin concentration independent of clinical conditions studied. Our results imply that total and HMW adiponectin have similar utility when assessing adiponectin levels in blood, as the ratio is independent of clinical condition. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. Effects of Varying RedoxConditions on Natural Attenuation of Inorganic Contaminants from the D-Area Coal Pile Runoff Basin (U)

    Energy Technology Data Exchange (ETDEWEB)

    Kaplan, D

    2004-05-30

    The objective of this study was to provide geochemical parameters to characterize the D-Area Coal Pile Runoff Basin (DCPRB) sediment as a potential source term. It is anticipated that the measured values will be used in risk calculations and will provide additional technical support for imposing Monitored Natural Attenuation at D-Area. This study provides a detailed evaluation of the DCPRB sediment and is part of another study that quantified the Monitored Natural Attenuation of inorganic contaminants more broadly at the D-Area Expanded Operable Unit, which includes the DCPRB (Powell et al. 2004). Distribution coefficients (K{sub d} values; a solid to liquid contaminant concentration ratio) and the Potentially Leachable Fraction (the percent of the total contaminant concentration in the sediment that can likely contribute to a contaminant plume) were measured in a DCPRB sediment as a function of redox conditions. Redox conditions at the DCPRB are expected to vary greatly as the system undergoes varying drying and flooding conditions. Conservative values; K{sub d} values that err on the side of being too low and Potentially Leachable Fraction values that err on the side of being too high, are presented. The K{sub d} values are high compared to conservative literature values, and underscores the importance of measuring site-specific values to provide estimates of sediments natural attenuation/sorption capacities. The Potentially Leachable Fraction indicates that as little as 27% of the As, but all of the Cu and Tl will be part of the source term. In the case of the As, the remaining 83% will likely never leach out of the sediment, thereby providing a form of natural attenuation. Importantly, Be, Cr, Cu, Ni, and V concentrations in the sediment were less-than twice background levels, indicating this sediment was not a potential source for these contaminants. K{sub d} values generally increased significantly (As, Cd, Co, Cr, Cu, Ni, Se, and Tl) when the sediment was

  7. Effects of initial conditions on self-similarity in a co-flowing axi-symmetric round jet

    International Nuclear Information System (INIS)

    Uddin, M.; Pollard, A.

    2004-01-01

    The effect of initial conditions of a spatially developing coflowing jet is investigated using an LES at Re D = 7,300. A co-flow velocity to initial jet centerline velocity ratio of 1:11 and a co-flow to initial jet diameter ratio of 35:1 are used to match the flow cases of Reference 11. The 35D x 135D simulation volume is divided into 1024 x 256 x 128 control volumes in the longitudinal, radial and azimuthal directions respectively. Time averaged results of the effect of initial conditions on mean flow, the decay of jet centreline velocity, growth of the jet and the distribution of Reynolds stresses in the near, and far field of the shear layer is presented. These quantities show good agreement with the measurements of Reference 11. Our results suggest that the first order moments, e.g., decay of centreline velocity excess, the radial mean velocity profiles, have little dependence on the initial conditions. As well, the Reynolds shear stress appears to have lesser sensitivity to the variation of initial velocity profiles. However, initial conditions have pronounced effect on the self-similarity of normal stresses. Additionally, the computations indicate little Reynolds number dependency, which is consistent with Townsend's school of thought. (author)

  8. Attribution of soil moisture dynamics - Initial conditions vs. atmospheric forcing and the role of climate change

    Science.gov (United States)

    Orth, Rene; Seneviratne, Sonia I.

    2014-05-01

    conditions versus the atmospheric forcing for monthly soil moisture variations. We find that initial soil moisture anomalies are overall more important than the forcing, even if less pronounced in summer. Especially in southern Europe we show high drought forecasting potential, whereas the forcing is more important in Central and North-eastern Europe.

  9. Analysis of grain growth process in melt spun Fe-B alloys under the initial saturated grain boundary segregation condition

    International Nuclear Information System (INIS)

    Chen, Z.; Liu, F.; Yang, X.Q.; Fan, Y.; Shen, C.J.

    2012-01-01

    Highlights: → We compared pure kinetic, pure thermodynamic and extended thermo-kinetic models. → An initial saturated GB segregation condition of nanoscale Fe-B alloys was determined. → The controlled-mechanism was proposed using two characteristic times (t 1 and t 2 ). - Abstract: A grain growth process in the melt spun low-solid-solubility Fe-B alloys was analyzed under the initial saturated grain boundary (GB) segregation condition. Applying melt spinning technique, single-phase supersaturated nanograins were prepared. Grain growth behavior of the single-phase supersaturated nanograins was investigated by performing isothermal annealing at 700 deg. C. Combined with the effect of GB segregation on the initial GB excess amount, the thermo-kinetic model [Chen et al., Acta Mater. 57 (2009) 1466] was extended to describe the initial GB segregation condition of nanoscale Fe-B alloys. In comparison of pure kinetic model, pure thermodynamic model and the extended thermo-kinetic model, an initial saturated GB segregation condition was determined. The controlled-mechanism of grain growth under initial saturated GB segregation condition was proposed using two characteristic annealing times (t 1 and t 2 ), which included a mainly kinetic-controlled process (t ≤ t 1 ), a transition from kinetic-mechanism to thermodynamic-mechanism (t 1 2 ) and pure thermodynamic-controlled process (t ≥ t 2 ).

  10. An initial study on the estimation of time-varying volumetric treatment images and 3D tumor localization from single MV cine EPID images

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, Pankaj, E-mail: pankaj.mishra@varian.com; Mak, Raymond H.; Rottmann, Joerg; Bryant, Jonathan H.; Williams, Christopher L.; Berbeco, Ross I.; Lewis, John H. [Brigham and Women' s Hospital, Dana-Farber Cancer Institute and Harvard Medical School, Boston, Massachusetts 02115 (United States); Li, Ruijiang [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California 94305 (United States)

    2014-08-15

    Purpose: In this work the authors develop and investigate the feasibility of a method to estimate time-varying volumetric images from individual MV cine electronic portal image device (EPID) images. Methods: The authors adopt a two-step approach to time-varying volumetric image estimation from a single cine EPID image. In the first step, a patient-specific motion model is constructed from 4DCT. In the second step, parameters in the motion model are tuned according to the information in the EPID image. The patient-specific motion model is based on a compact representation of lung motion represented in displacement vector fields (DVFs). DVFs are calculated through deformable image registration (DIR) of a reference 4DCT phase image (typically peak-exhale) to a set of 4DCT images corresponding to different phases of a breathing cycle. The salient characteristics in the DVFs are captured in a compact representation through principal component analysis (PCA). PCA decouples the spatial and temporal components of the DVFs. Spatial information is represented in eigenvectors and the temporal information is represented by eigen-coefficients. To generate a new volumetric image, the eigen-coefficients are updated via cost function optimization based on digitally reconstructed radiographs and projection images. The updated eigen-coefficients are then multiplied with the eigenvectors to obtain updated DVFs that, in turn, give the volumetric image corresponding to the cine EPID image. Results: The algorithm was tested on (1) Eight digital eXtended CArdiac-Torso phantom datasets based on different irregular patient breathing patterns and (2) patient cine EPID images acquired during SBRT treatments. The root-mean-squared tumor localization error is (0.73 ± 0.63 mm) for the XCAT data and (0.90 ± 0.65 mm) for the patient data. Conclusions: The authors introduced a novel method of estimating volumetric time-varying images from single cine EPID images and a PCA-based lung motion model

  11. Behavior of small-sized BWR fuel under reactivity initiated accident conditions

    International Nuclear Information System (INIS)

    Yanagisawa, Kazuaki; Fujishiro, Toshio; Horiki, Oichiro; Chen Dianshan; Takeuchi, Kiyoshi.

    1992-01-01

    The present work was performed on this small-sized BWR fuel, where Zr liner and rod prepressurization were taken as experimental parameters. Experiment was done under simulated reactivity initiated accident (RIA) conditions at Nuclear Safety Research Reactor (NSRR) belonged to Japan Atomic Energy Research Institute (JAERI). Major remarks obtained are as follows: (1) Three different types of the fuel rods consisted of (a) Zr lined/pressurized (0.65MPa), (b) Zr lined/non-pressurized and (c) non-Zr lined/pressurized (o.65MPa) were used, respectively. Failure thresholds of these were not less than that (260 cal/g·fuel) described in Japanese RIA Licensing Guideline. Small-sized BWR and conventional 8 x 8 BWR fuels were considered to be in almost the same level in failure threshold. Failure modes of the three were (a) cladding melt/brittle, (b) cladding melt/brittle and (c) rupture by large ballooning, respectively. (2) The magnitude of pressure pulse at fuel fragmentation was also studied by lined/pressurized and non-lined/pressurized fuels. Above the energy deposition of 370 cal/g·fuel, mechanical energy (or pressure) was found to be released from these fragmented fuels. No measurable difference was, however, observed between the tested fuels and NSRR standard (and conventional 8 x 8 BWR) fuels. (3) It is worthy of mentioning that Zr liner tended to prevent the cladding from large ballooning. Non-lined/pressurized fuel tended to cause wrinkle deformation at cladding. Hence, cladding external was notched much by the wrinkles. (4) Time to fuel failure measured from the tested BWR fuels (pressurization < 0.6MPA) was longer than that measured from PWR fuels (pressurization < 3.2MPa). The magnitude of the former was of the order of 3 ∼ 6s, while that of the latter was < 1s. (J.P.N.)

  12. SCC of cold-worked austenitic stainless steels exposed to PWR primary water conditions: susceptibility to initiation

    International Nuclear Information System (INIS)

    Herms, E.; Raquet, O.; Sejourne, L.; Vaillant, F.

    2009-01-01

    Heavily cold-worked austenitic stainless steels (AISI 304L and 316L types) could be significantly susceptible to Stress Corrosion Cracking (SCC) when exposed to PWR nominal primary water conditions even in absence of any pollutants. Susceptibility to SCC was shown to be related with some conditions such as initial hardness, procedure of cold-work or dynamic straining. A dedicated program devoted to better understand the initiation stage on CW austenitic stainless steels in PWR water is presented. Initiation is studied thanks to SCC test conditions leading to an intergranular cracking propagation mode on a CW austenitic stainless steel which is the mode generally reported after field experience. SCC tests are carried out in typical primary water conditions (composition 1000 ppm B and 2 ppm Li) and for temperature in the range 290 - 340 C. Material selected is 316L cold-worked essentially by rolling (reduction in thickness of 40%). Initiation tests are carried out under various stress levels with the aim to investigate the evolution of the initiation period versus the value of applied stress. SCC tests are performed on cylindrical notched specimens in order to increase the applied stress and allow accelerated testing without modify the exposure conditions to strictly nominal hydrogenated PWR water. Respective influences of cyclic/dynamic conditions on SCC initiation are presented and discussed. Dedicated interrupted tests help to investigate the behaviour of the crack initiation process. These SCC tests have shown that crack initiation could be obtained after a very short time under dynamic loading conditions on heavily pre-strained austenitic stainless steels. Actual results show that the most limiting stage of the cracking process on CW 316L seems to be the transition from slow transgranular propagation of surface initiated cracks to intergranular fast propagation through the thickness of the sample. The duration of this stage during crack initiation tests is

  13. STAR FORMATION AT VERY LOW METALLICITY. V. THE GREATER IMPORTANCE OF INITIAL CONDITIONS COMPARED TO METALLICITY THRESHOLDS

    International Nuclear Information System (INIS)

    Jappsen, Anne-Katharina; Low, Mordecai-Mark Mac; Glover, Simon C. O.; Klessen, Ralf S.; Kitsionas, Spyridon

    2009-01-01

    The formation of the first stars out of metal-free gas appears to result in stars at least an order of magnitude more massive than in the present-day case. We here consider what controls the transition from a primordial to a modern initial mass function. It has been proposed that this occurs when effective metal line cooling occurs at a metallicity threshold of Z/Z sun > 10 -3.5 . We study the influence of low levels of metal enrichment on the cooling and collapse of initially ionized gas in small protogalactic halos using three-dimensional, smoothed particle hydrodynamics simulations with particle splitting. Our initial conditions represent protogalaxies forming within a previously ionized H II region that has not yet had time to cool and recombine. These differ considerably from those used in simulations predicting a metallicity threshold, where the gas was initially cold and only partially ionized. In the centrally condensed potential that we study here, a wide variety of initial conditions for the gas yields a monolithic central collapse. Our models show no fragmentation during collapse to number densities as high as 10 5 cm -3 , for metallicities reaching as high as 10 -1 Z sun , far above the threshold suggested by previous work. Rotation allows for the formation of gravitationally stable gas disks over large fractions of the local Hubble time. Turbulence slows the growth of the central density slightly, but both spherically symmetric and turbulent initial conditions collapse and form a single sink particle. We therefore argue that fragmentation at moderate density depends on the initial conditions for star formation more than on the metal abundances present. The actual initial conditions to be considered still need to be determined in detail by observation and modeling of galaxy formation. Metal abundance may still drive fragmentation at very high densities due to dust cooling, perhaps giving an alternative metallicity threshold.

  14. Assessing and monitoring the effects of filter material amendments on the biophysicochemical properties during composting of solid winery waste under open field and varying climatic conditions.

    Science.gov (United States)

    Mtimkulu, Y; Meyer, A H; Mulidzi, A R; Shange, P L; Nchu, F

    2017-01-01

    Waste management in winery and distillery industries faces numerous disposal challenges as large volumes of both liquid and solid waste by-products are generated yearly during cellar practices. Composting has been suggested as a feasible option to beneficiate solid organic waste. This incentivized the quest for efficient composting protocols to be put in place. The objective of this study was to experiment with different composting strategies for spent winery solid waste. Compost materials consisting of chopped pruning grape stalks, skins, seed and spent wine filter material consisting of a mixture of organic and inorganic expend ingredients were mixed in compost heaps. The filter material component varied (in percentage) among five treatments: T1 (40%) lined, T2 (20%) lined, T3 (0%) lined, T4 (40%) ground material, lined and T5 (40%) unlined. Composting was allowed to proceed under open field conditions over 12months, from autumn to summer. Indicators such as temperature, moisture, enzyme activities, microbial counts, pH, and C/N ratio, were recorded. Generally, season (df=3, 16, Pwinery solid waste. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. A CLUSTER IN THE MAKING: ALMA REVEALS THE INITIAL CONDITIONS FOR HIGH-MASS CLUSTER FORMATION

    International Nuclear Information System (INIS)

    Rathborne, J. M.; Contreras, Y.; Longmore, S. N.; Bastian, N.; Jackson, J. M.; Alves, J. F.; Bally, J.; Foster, J. B.; Garay, G.; Kruijssen, J. M. D.; Testi, L.; Walsh, A. J.

    2015-01-01

    G0.253+0.016 is a molecular clump that appears to be on the verge of forming a high-mass cluster: its extremely low dust temperature, high mass, and high density, combined with its lack of prevalent star formation, make it an excellent candidate for an Arches-like cluster in a very early stage of formation. Here we present new Atacama Large Millimeter/Sub-millimeter Array observations of its small-scale (∼0.07 pc) 3 mm dust continuum and molecular line emission from 17 different species that probe a range of distinct physical and chemical conditions. The data reveal a complex network of emission features with a complicated velocity structure: there is emission on all spatial scales, the morphology of which ranges from small, compact regions to extended, filamentary structures that are seen in both emission and absorption. The dust column density is well traced by molecules with higher excitation energies and critical densities, consistent with a clump that has a denser interior. A statistical analysis supports the idea that turbulence shapes the observed gas structure within G0.253+0.016. We find a clear break in the turbulent power spectrum derived from the optically thin dust continuum emission at a spatial scale of ∼0.1 pc, which may correspond to the spatial scale at which gravity has overcome the thermal pressure. We suggest that G0.253+0.016 is on the verge of forming a cluster from hierarchical, filamentary structures that arise from a highly turbulent medium. Although the stellar distribution within high-mass Arches-like clusters is compact, centrally condensed, and smooth, the observed gas distribution within G0.253+0.016 is extended, with no high-mass central concentration, and has a complex, hierarchical structure. If this clump gives rise to a high-mass cluster and its stars are formed from this initially hierarchical gas structure, then the resulting cluster must evolve into a centrally condensed structure via a dynamical process

  16. Surface-Initiated Graft Atom Transfer Radical Polymerization of Methyl Methacrylate from Chitin Nanofiber Macroinitiator under Dispersion Conditions

    Directory of Open Access Journals (Sweden)

    Ryo Endo

    2015-08-01

    Full Text Available Surface-initiated graft atom transfer radical polymerization (ATRP of methyl methacrylate (MMA from self-assembled chitin nanofibers (CNFs was performed under dispersion conditions. Self-assembled CNFs were initially prepared by regeneration from a chitin ion gel with 1-allyl-3-methylimidazolium bromide using methanol; the product was then converted into the chitin nanofiber macroinitiator by reaction with α-bromoisobutyryl bromide in a dispersion containing N,N-dimethylformamide. Surface-initiated graft ATRP of MMA from the initiating sites on the CNFs was subsequently carried out under dispersion conditions, followed by filtration to obtain the CNF-graft-polyMMA film. Analysis of the product confirmed the occurrence of the graft ATRP on the surface of the CNFs.

  17. Variability of the morphometric features of Calliphora vicina (Diptera, Calliphoridae under the varying and constant micro-climatic condi-tions

    Directory of Open Access Journals (Sweden)

    L. I. Faly

    2013-03-01

    Full Text Available Variability of the main morphometric features of imago flies Calliphora vicina R.-D. (Diptera, Calliphoridae of two samples was studied. First sample consists of individuals caught in the wild (park ecosystems of Dnipropetrovsk, the second one – specimens cultured in the laboratory under the constant temperature and humidity. Possible using of C. vicina R.-D. as a bioindicator of anthropogenic factors is analysed. Environmental factors may act as the stimulators of adaptive changes in physiological functions, as the constraints that cause impossibility of the existence of certain species in particular conditions, and as modifiers that determine the morpho- anatomical and physiological changes in organisms. The most significant differences between studied samples were found for the width (“laboratory” individuals are characterized by larger head size and for the length of limbs segments. The fluctuating range of the head width in specimens collected in the wild is much wider, due to the heterogeneity of the micro-climatic conditions of the larvae development and trophic resources. Maximal negative asymmetry of the head width is observed in individuals C. vicina R.-D. of the “natural” sample as compared with “laboratory” individuals. Among imagoes caught in the wild the individuals with a relatively wide head are dominated, as evidenced by the large positive value of kurtosis. At the same time, the distribution of values in “laboratory” individuals is almost normal. In adults bred in the laboratory the shortening of segments of the leg pair I is observed in comparison with the individuals of “natural” sample. Similar results were recorded for other insect groups cultivated in a laboratory. For most other linear measurements of the C. vicina R.-D. body the differences between samples are not registered. Ephemeral existence of the substrate of blow flies leads to higher prevailing evolutionary adaptation of species to varying

  18. Conservadorismo condicional: estudo a partir de variáveis econômicas Conditional conservatism: a study based on economic variables

    Directory of Open Access Journals (Sweden)

    Rafael de Lacerda Moreira

    2010-12-01

    Full Text Available A Contabilidade, na perspectiva da abordagem da informação, volta-se à utilidade da informação. O Conservadorismo Condicional está ligado à tendência de a Contabilidade exigir um maior grau de verificação das boas notícias para reconhecê-las no resultado em relação ao grau de verificação das más notícias. Em face das preocupações referentes à qualidade da informação contábil, o objetivo deste artigo consiste em analisar o reflexo do Conservadorismo Condicional no resultado contábil a partir de variáveis econômicas. O estudo utiliza o Modelo Reverso de Lucros Associados a Retornos (BASU, 1997 e o modelo proposto por Kahn e Watts (2009, que analisam a relação entre as variáveis lucro contábil e retorno econômico, utilizando os valores dos retornos positivos e negativos como proxy de boas e más notícias, e outras variáveis largamente aceitas na avaliação do conservadorismo. Para tanto, foram estimados os modelos estatísticos para uma amostra de 96 empresas para o período de 2005 a 2007 partindo de informações anuais disponíveis no Economática® e dados reportados em notas explicativas. Com o objetivo de selecionar um evento econômico que pode impactar no reconhecimento assimétrico do resultado econômico, decidiu-se comparar os resultados entre empresas listadas nos níveis de governança da Bovespa com as demais empresas. Os resultados obtidos confirmam a hipótese de utilização de conservadorismo condicional na mensuração do resultado das companhias da amostra. A diferenciação positiva quanto ao grau de conservadorismo para as empresas que aderiram aos níveis de governança não são conclusivas, visto que os modelos apresentaram resultados dispersos. As variáveis econômicas criam vantagens quando as más notícias não podem ser tão claramente visíveis nas Demonstrações Contábeis, podendo diminuir os resultados futuros esperados.Accounting from an information perspective looks at the

  19. Evaluation of strength and failure of brittle rock containing initial cracks under lithospheric conditions

    Science.gov (United States)

    Li, Xiaozhao; Qi, Chengzhi; Shao, Zhushan; Ma, Chao

    2018-02-01

    Natural brittle rock contains numerous randomly distributed microcracks. Crack initiation, growth, and coalescence play a predominant role in evaluation for the strength and failure of brittle rocks. A new analytical method is proposed to predict the strength and failure of brittle rocks containing initial microcracks. The formulation of this method is based on an improved wing crack model and a suggested micro-macro relation. In this improved wing crack model, the parameter of crack angle is especially introduced as a variable, and the analytical stress-crack relation considering crack angle effect is obtained. Coupling the proposed stress-crack relation and the suggested micro-macro relation describing the relation between crack growth and axial strain, the stress-strain constitutive relation is obtained to predict the rock strength and failure. Considering different initial microcrack sizes, friction coefficients and confining pressures, effects of crack angle on tensile wedge force acting on initial crack interface are studied, and effects of crack angle on stress-strain constitutive relation of rocks are also analyzed. The strength and crack initiation stress under different crack angles are discussed, and the value of most disadvantaged angle triggering crack initiation and rock failure is founded. The analytical results are similar to the published study results. Rationality of this proposed analytical method is verified.

  20. Straw incorporation increases crop yield and soil organic carbon sequestration but varies under different natural conditions and farming practices in China: a system analysis

    Directory of Open Access Journals (Sweden)

    X. Han

    2018-04-01

    Full Text Available Loss of soil organic carbon (SOC from agricultural soils is a key indicator of soil degradation associated with reductions in net primary productivity in crop production systems worldwide. Technically simple and locally appropriate solutions are required for farmers to increase SOC and to improve cropland management. In the last 30 years, straw incorporation (SI has gradually been implemented across China in the context of agricultural intensification and rural livelihood improvement. A meta-analysis of data published before the end of 2016 was undertaken to investigate the effects of SI on crop production and SOC sequestration. The results of 68 experimental studies throughout China in different edaphic conditions, climate regions and farming regimes were analyzed. Compared with straw removal (SR, SI significantly sequestered SOC (0–20 cm depth at the rate of 0.35 (95 % CI, 0.31–0.40 Mg C ha−1 yr−1, increased crop grain yield by 13.4 % (9.3–18.4 % and had a conversion efficiency of the incorporated straw C of 16 % ± 2 % across China. The combined SI at the rate of 3 Mg C ha−1 yr−1 with mineral fertilizer of 200–400 kg N ha−1 yr−1 was demonstrated to be the best farming practice, where crop yield increased by 32.7 % (17.9–56.4 % and SOC sequestrated by the rate of 0.85 (0.54–1.15 Mg C ha−1 yr−1. SI achieved a higher SOC sequestration rate and crop yield increment when applied to clay soils under high cropping intensities, and in areas such as northeast China where the soil is being degraded. The SOC responses were highest in the initial starting phase of SI, then subsequently declined and finally became negligible after 28–62 years. However, crop yield responses were initially low and then increased, reaching their highest level at 11–15 years after SI. Overall, our study confirmed that SI created a positive feedback loop of SOC enhancement together with

  1. Straw incorporation increases crop yield and soil organic carbon sequestration but varies under different natural conditions and farming practices in China: a system analysis

    Science.gov (United States)

    Han, Xiao; Xu, Cong; Dungait, Jennifer A. J.; Bol, Roland; Wang, Xiaojie; Wu, Wenliang; Meng, Fanqiao

    2018-04-01

    Loss of soil organic carbon (SOC) from agricultural soils is a key indicator of soil degradation associated with reductions in net primary productivity in crop production systems worldwide. Technically simple and locally appropriate solutions are required for farmers to increase SOC and to improve cropland management. In the last 30 years, straw incorporation (SI) has gradually been implemented across China in the context of agricultural intensification and rural livelihood improvement. A meta-analysis of data published before the end of 2016 was undertaken to investigate the effects of SI on crop production and SOC sequestration. The results of 68 experimental studies throughout China in different edaphic conditions, climate regions and farming regimes were analyzed. Compared with straw removal (SR), SI significantly sequestered SOC (0-20 cm depth) at the rate of 0.35 (95 % CI, 0.31-0.40) Mg C ha-1 yr-1, increased crop grain yield by 13.4 % (9.3-18.4 %) and had a conversion efficiency of the incorporated straw C of 16 % ± 2 % across China. The combined SI at the rate of 3 Mg C ha-1 yr-1 with mineral fertilizer of 200-400 kg N ha-1 yr-1 was demonstrated to be the best farming practice, where crop yield increased by 32.7 % (17.9-56.4 %) and SOC sequestrated by the rate of 0.85 (0.54-1.15) Mg C ha-1 yr-1. SI achieved a higher SOC sequestration rate and crop yield increment when applied to clay soils under high cropping intensities, and in areas such as northeast China where the soil is being degraded. The SOC responses were highest in the initial starting phase of SI, then subsequently declined and finally became negligible after 28-62 years. However, crop yield responses were initially low and then increased, reaching their highest level at 11-15 years after SI. Overall, our study confirmed that SI created a positive feedback loop of SOC enhancement together with increased crop production, and this is of great practical importance to straw management as agriculture

  2. Corrosion fatigue initiation and short crack growth behaviour of austenitic stainless steels under light water reactor conditions

    International Nuclear Information System (INIS)

    Seifert, H.P.; Ritter, S.; Leber, H.J.

    2012-01-01

    Highlights: ► Corrosion fatigue in austenitic stainless steels under light water reactor conditions. ► Identification of major parameters of influence on initiation and short crack growth. ► Critical system conditions for environmental reduction of fatigue initiation life. ► Comparison with the environmental factor (F env ) approach. - Abstract: The corrosion fatigue initiation and short crack growth behaviour of different wrought low-carbon and stabilised austenitic stainless steels was characterised under simulated boiling water reactor and pressurised water reactor primary water conditions by cyclic fatigue tests with sharply notched fracture mechanics specimens. The special emphasis was placed to the behaviour at low corrosion potentials and, in particular, to hydrogen water chemistry conditions. The major parameter effects and critical conjoint threshold conditions, which result in relevant environmental reduction and acceleration of fatigue initiation life and subsequent short crack growth, respectively, are discussed and summarised. The observed corrosion fatigue behaviour is compared with the fatigue evaluation procedures in codes and regulatory guidelines.

  3. Reverse engineering of heavy-ion collisions: Unraveling initial conditions from anisotropic flow data

    International Nuclear Information System (INIS)

    Retinskaya, Ekaterina

    2014-01-01

    Ultra-Relativistic heavy-ion physics is a promising field of high energy physics connecting two fields: nuclear physics and elementary particle physics. Experimental achievements of the last years have provided an opportunity to study the properties of a new state of matter created in heavy-ion collisions called quark-gluon plasma. The initial state of two colliding nuclei is affected by fluctuations coming from wave- functions of nucleons. These fluctuations lead to the momentum anisotropy of the hadronic matter which is observed by the detectors. The system created in the collision behaves like a fluid, so the initial state is connected to the final state via hydrodynamic evolution. In this thesis we model the evolution with relativistic viscous hydrodynamics. Our results, combined with experimental data, give non trivial constraints on the initial state, thus achieving 'reverse engineering' of the heavy-ion collisions. The observable which characterizes the momentum anisotropy is the anisotropic flow v n . We present the first measurements of the first harmonic of the anisotropic flow called directed flow v 1 in Pb-Pb collisions at the LHC. We then perform the first viscous hydrodynamic modeling of directed flow and show that it is less sensitive to viscosity than higher harmonics. Comparison of these experimental data with the modeling allows to extract the values of the dipole asymmetry of the initial state, which provides constraints on the models of initial states. A prediction for directed flow v 1 in Au-Au collisions is also made for RHIC. We then perform a similar modeling of the second and third harmonics of the anisotropic flow, called respectively elliptic v 2 and triangular v 3 flow. A combined analysis of the elliptic and triangular flow data compared with viscous hydrodynamic calculations allows us to put constraints on initial ellipticity and triangularity of the system. These constraints are then used as a filter for different models of

  4. Fate of As(V)-treated nano zero-valent iron: determination of arsenic desorption potential under varying environmental conditions by phosphate extraction.

    Science.gov (United States)

    Dong, Haoran; Guan, Xiaohong; Lo, Irene M C

    2012-09-01

    Nano zero-valent iron (NZVI) offers a promising approach for arsenic remediation, but the spent NZVI with elevated arsenic content could arouse safety concerns. This study investigated the fate of As(V)-treated NZVI (As-NZVI), by examining the desorption potential of As under varying conditions. The desorption kinetics of As from As-NZVI as induced by phosphate was well described by a biphasic rate model. The effects of As(V)/NZVI mass ratio, pH, and aging time on arsenic desorption from As-NZVI by phosphate were investigated. Less arsenic desorption was observed at lower pH or higher As(V)/NZVI mass ratio, where stronger complexes (bidentate) formed between As(V) and NZVI corrosion products as indicated by FTIR analysis. Compared with the fresh As-NZVI, the amount of phosphate-extractable As significantly decreased in As-NZVI aged for 30 or 60 days. The results of the sequential extraction experiments demonstrated that a larger fraction of As was sorbed in the crystalline phases after aging, making it less susceptible to phosphate displacement. However, at pH 9, a slightly higher proportion of phosphate-extractable As was observed in the 60-day sample than in the 30-day sample. XPS results revealed the transformation of As(V) to more easily desorbed As(III) during aging and a higher As(III)/As(V) ratio in the 60-day sample at pH 9, which might have resulted in the higher desorption. Copyright © 2012 Elsevier Ltd. All rights reserved.

  5. Successful transportation of human corneal endothelial tissues without cool preservation in varying Indian tropical climatic conditions and in vitro cell expansion using a novel polymer.

    Science.gov (United States)

    Rao, Srinivas K; Sudhakar, John; Parikumar, Periyasamy; Natarajan, Sundaram; Insaan, Aditya; Yoshioka, Hiroshi; Mori, Yuichi; Tsukahara, Shigeo; Baskar, Subramani; Manjunath, Sadananda Rao; Senthilkumar, Rajappa; Thamaraikannan, Paramasivam; Srinivasan, Thangavelu; Preethy, Senthilkumar; Abraham, Samuel J K

    2014-02-01

    Though the transplantation of human corneal endothelial tissue (CET) separated from cadaver cornea is in practice, its transportation has not been reported. We report the successful transportation of CET in varying Indian climatic conditions without cool preservation and the in vitro expansion of Human Corneal Endothelial Precursor Cells (HCEPCs) using a novel Thermo-reversible gelation polymer (TGP). CET from cadaver corneas (n = 67), unsuitable for transplantation, were used. In phase I, CET was transported in Basal Culture Medium (Group I) and TGP (Group II) and in Phase II, in TGP cocktail alone, from three hospitals 250-2500 km away, to a central laboratory. The transportation time ranged from 6 h to 72 h and the outdoor temperature between 20°C and 41°C. On arrival, CET were processed, cells were expanded upto 30 days in basal culture medium (Group A) and TGP scaffold (Group B). Cell viability and morphology were documented and Reverse transcription polymerase chain reaction (RT-PCR) characterization undertaken. In Phase I, TGP yielded more viable cells (0.11 × 10(6) cells) than Group I (0.04 × 10(6) cells). In Phase II, the average cell count was 5.44 × 10(4) cells. During expansion, viability of HCEPCs spheres in TGP was maintained for a longer duration. The cells from both the groups tested positive for B-3 tubulin and negative for cytokeratins K3 and K12, thereby proving them to be HCEPCs. TGP preserves the CET during transportation without cool preservation and supports in vitro expansion, with a higher yield of HCEPCs, similar to that reported in clinical studies.

  6. Successful transportation of human corneal endothelial tissues without cool preservation in varying Indian tropical climatic conditions and in vitro cell expansion using a novel polymer

    Directory of Open Access Journals (Sweden)

    Srinivas K Rao

    2014-01-01

    Full Text Available Background: Though the transplantation of human corneal endothelial tissue (CET separated from cadaver cornea is in practice, its transportation has not been reported. We report the successful transportation of CET in varying Indian climatic conditions without cool preservation and the in vitro expansion of Human Corneal Endothelial Precursor Cells (HCEPCs using a novel Thermo-reversible gelation polymer (TGP. Materials and Methods: CET from cadaver corneas (n = 67, unsuitable for transplantation, were used. In phase I, CET was transported in Basal Culture Medium (Group I and TGP (Group II and in Phase II, in TGP cocktail alone, from three hospitals 250-2500 km away, to a central laboratory. The transportation time ranged from 6 h to 72 h and the outdoor temperature between 20°C and 41°C. On arrival, CET were processed, cells were expanded upto 30 days in basal culture medium (Group A and TGP scaffold (Group B. Cell viability and morphology were documented and Reverse transcription polymerase chain reaction (RT-PCR characterization undertaken. Results: In Phase I, TGP yielded more viable cells (0.11 × 10 6 cells than Group I (0.04 × 10 6 cells. In Phase II, the average cell count was 5.44 × 10 4 cells. During expansion, viability of HCEPCs spheres in TGP was maintained for a longer duration. The cells from both the groups tested positive for B-3 tubulin and negative for cytokeratins K3 and K12, thereby proving them to be HCEPCs. Conclusion: TGP preserves the CET during transportation without cool preservation and supports in vitro expansion, with a higher yield of HCEPCs, similar to that reported in clinical studies.

  7. 42 CFR 418.54 - Condition of participation: Initial and comprehensive assessment of the patient.

    Science.gov (United States)

    2010-10-01

    ... patient's well-being, comfort, and dignity throughout the dying process. The comprehensive assessment must... and participate in his or her own care. (4) Imminence of death. (5) Severity of symptoms. (6) Drug... their ability to cope with the patient's death. Information gathered from the initial bereavement...

  8. Modeling precipitation thermodynamics and kinetics in type 316 austenitic stainless steels with varying composition as an initial step toward predicting phase stability during irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Shim, Jae-Hyeok, E-mail: jhshim@kist.re.kr [Department of Nuclear Engineering, University of Tennessee, Knoxville, TN 37996 (United States); High Temperature Energy Materials Research Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Povoden-Karadeniz, Erwin [Christian Doppler Laboratory for Early Stages of Precipitation, Vienna University of Technology, A-1040 Vienna (Austria); Kozeschnik, Ernst [Institute of Materials Science and Technology, Vienna University of Technology, A-1040 Vienna (Austria); Wirth, Brian D. [Department of Nuclear Engineering, University of Tennessee, Knoxville, TN 37996 (United States)

    2015-07-15

    Highlights: • We model the precipitation kinetics in irradiated 316 austenitic stainless steels. • Radiation-induced phases are predicted to form at over 10 dpa segregation conditions. • The Si content is the most critical for the formation of radiation-induced phases. - Abstract: The long-term evolution of precipitates in type 316 austenitic stainless steels at 400 °C has been simulated using a numerical model based on classical nucleation theory and the thermodynamic extremum principle. Particular attention has been paid to the precipitation of radiation-induced phases such as γ′ and G phases. In addition to the original compositions, the compositions for radiation-induced segregation at a dose level of 5, 10 or 20 dpa have been used in the simulation. In a 316 austenitic stainless steel, γ′ appears as the main precipitate with a small amount of G phase forming at 10 and 20 dpa. On the other hand, G phase becomes relatively dominant over γ′ at the same dose levels in a Ti-stabilized 316 austenitic stainless steel, which tends to suppress the formation of γ′. Among the segregated alloying elements, the concentration of Si seems to be the most critical for the formation of radiation-induced phases. An increase in dislocation density as well as increased diffusivity of Mn and Si significantly enhances the precipitation kinetics of the radiation-induced phases within this model.

  9. Efficient Procedure to Compute the Microcanonical Volume of Initial Conditions that Lead to Escape Trajectories from a Multidimensional Potential Well

    NARCIS (Netherlands)

    Waalkens, Holger; Burbanks, Andrew; Wiggins, Stephen

    2005-01-01

    A procedure is presented for computing the phase space volume of initial conditions for trajectories that escape or ‘‘react’’ from a multidimensional potential well. The procedure combines a phase space transition state theory, which allows one to construct dividing surfaces that are free of local

  10. Features of the development of round jets for different initial conditions and in the presence of obstacles

    Science.gov (United States)

    Kozlov, V. V.; Litvinenko, M. V.; Litvinenko, Yu. A.; Kozlov, G. V.

    2016-10-01

    The goal of this work is an experimental study of the influence of the initial conditions (nozzle configuration, mean velocity profile at the nozzle exit, surface roughness, and jet diameter) on the flow structure in a round jet by various methods: hot-wire anemometry, smoke visualization, and particle image velocimetry (PIV).

  11. On the initial conditions of time-dependent mean-field equations of evolution. Pt. 2

    International Nuclear Information System (INIS)

    Troudet, T.; Paris-11 Univ., 91 - Orsay

    1986-01-01

    We analyze the problem so far untouched of determining the initial mean-field wavefunction in the context of zero-temperature mean-field descriptions of time-dependent expectation values and quantum fluctuations of nuclear observables. The nucleus, at zero temperature, is taken to be in a low-lying excited many-body eigenstate and is approximated by the corresponding RPA wavefunction as a continuous superposition of coherent states (i.e. Slater determinants). A generating function Gsub(A)(lambda) for time-dependent expectation values and quantum fluctuations is constructed within the formalism of functional integration. By applying the saddle-point method to the functional action of Gsub(A)(lambda) and then taking its lambda-derivatives, we recover the well-known TDHF theory and propose a simple determination of the initial Slater determinant for an appropriate mean-field description of time-dependent expectation values. The analog mean-field description of quadratic-quantum fluctuations proceeds similarly and in addition includes the contribution of the uncorrelated TDHF-RPA phonons coupled to collective excitations of the initial (static) mean-field configuration. When the collective TDHF-RPA excitations are solely taken into account, we obtain an improved version of the Balian-Veneroni dispersion formula by showing how to determine the initial mean-field wavefunction. By first taking the lambda-derivatives of Gsub(A)(lambda) before applying the saddle-point method, the initial mean-field wavefunction is found to be non-linearly coupled to the mean-field dynamics themselves. In return, and in contrast to the first quantization scheme, these both depend non-trivially upon the observable A being measured so that approximations must be proposed to simplify the resulting mean-field equations. (orig.)

  12. Modifying mixing and instability growth through the adjustment of initial conditions in a high-energy-density counter-propagating shear experiment on OMEGA

    International Nuclear Information System (INIS)

    Merritt, E. C.; Doss, F. W.; Loomis, E. N.; Flippo, K. A.; Kline, J. L.

    2015-01-01

    Counter-propagating shear experiments conducted at the OMEGA Laser Facility have been evaluating the effect of target initial conditions, specifically the characteristics of a tracer foil located at the shear boundary, on Kelvin-Helmholtz instability evolution and experiment transition toward nonlinearity and turbulence in the high-energy-density (HED) regime. Experiments are focused on both identifying and uncoupling the dependence of the model initial turbulent length scale in variable-density turbulence models of k-ϵ type on competing physical instability seed lengths as well as developing a path toward fully developed turbulent HED experiments. We present results from a series of experiments controllably and independently varying two initial types of scale lengths in the experiment: the thickness and surface roughness (surface perturbation scale spectrum) of a tracer layer at the shear interface. We show that decreasing the layer thickness and increasing the surface roughness both have the ability to increase the relative mixing in the system, and thus theoretically decrease the time required to begin transitioning to turbulence in the system. We also show that we can connect a change in observed mix width growth due to increased foil surface roughness to an analytically predicted change in model initial turbulent scale lengths

  13. Tagged particle in single-file diffusion with arbitrary initial conditions

    Science.gov (United States)

    Cividini, J.; Kundu, A.

    2017-08-01

    We compute the full probability distribution of the positions of a tagged particle exactly for the given arbitrary initial positions of the particles, and for general single-particle propagators. We consider the thermodynamic limit of our exact expressions in quenched and annealed settings. For a particular class of single-particle propagators, the exact formula is expressed in a simple integral form in the quenched case whereas in the annealed case, it is expressed as a simple combination of Bessel functions. In particular, we focus on the step and the power-law initial configurations. In the former case, a drift is induced even when the one-particle propagators are symmetric. On the other hand, in the later case the scaling of the cumulants of the position of the tracer differs from the uniform case. We provide numerical verifications of our results.

  14. Initial conditions for hydrodynamics from weakly coupled pre-equilibrium evolution

    International Nuclear Information System (INIS)

    Mazeliauskas, Aleksas

    2017-01-01

    We use leading order effective kinetic theory to simulate the pre-equilibrium evolution of transverse energy and flow perturbations in heavy-ion collisions. We provide a Green function which propagates the initial perturbations of the energy-momentum tensor to a time when hydrodynamics becomes applicable. With this map, the pre-thermal evolution from saturated nuclei to hydrodynamics can be modeled in the framework of weakly coupled QCD. (paper)

  15. Market development of organic products in Europe: conditions and role of Organic Marketing Initiatives

    OpenAIRE

    Schmit, Otto; Fontguyon, Guy de; Sans, Pierre

    2007-01-01

    The contribution presents some of the main results of a European program of investigation (titled Organic Marketing Initiatives – OMIs – and Rural Development). Firstly, consumer behavior, as well as attitudes, expectations, motives and buying barriers concerning organic food are explored. Then, authors give a brief overview of the organic market analysis of 18 European countries, based on a Delphi inquiry. Finally, the third part highlights the role of OMIs in the organic market development ...

  16. Initial conditions of non-equilibrium quark-gluon plasma evolution

    International Nuclear Information System (INIS)

    Shmatov, S.V.

    2002-01-01

    In accordance with the hydrodynamic Bjorken limit, the initial energy density and temperature for a chemical non-equilibrium quark-gluon system formed in the heavy ion collisions at the LHC are computed. The dependence of this value on the type of colliding nuclei and the collision impact parameter is studied. The principle possibility of the non-equilibrium quark-gluon plasma (QGP) formation in the light nuclei collisions is shown. The life time of QGP is calculated. (author)

  17. Initial conditions for hydrodynamics from weakly coupled pre-equilibrium evolution

    CERN Document Server

    Keegan, Liam; Mazeliauskas, Aleksas; Teaney, Derek

    2016-01-01

    We use effective kinetic theory, accurate at weak coupling, to simulate the pre-equilibrium evolution of transverse energy and flow perturbations in heavy-ion collisions. We provide a Green function which propagates the initial perturbations to the energy-momentum tensor at a time when hydrodynamics becomes applicable. With this map, the complete pre-thermal evolution from saturated nuclei to hydrodynamics can be modelled in a perturbatively controlled way.

  18. Comparative estimation of inevitable endogenous ileal flow of amino acids in Pekin ducks under varying dietary or physiological conditions and their significance to nutritional requirements for amino acids.

    Science.gov (United States)

    Akinde, D O

    2017-10-01

    In 2 experiments in Pekin ducks the inevitable endogenous ileal flow (IEIF) of AA was estimated at changing intake and source of crude fiber (CF) or soybean oil (SO) level. Also the roles of dry matter intake (DMI) and BW or age as well as the proportion of IEIF in the dietary requirement for AA were studied. In experiment 1 three basal CP (20, 60, or 100 g/kg) diets were formulated containing a low CF (LCF, 30 g/kg) or high (HCF, 80 g/kg) level; achieved with cellulose supplementation. All diets were similar in every other respect including having SO content of 40 g/kg. Four floor pens of eight 85-day-old ducks were randomly allocated to each diet. Similar diets were mixed in experiment 2 but corn cob meal replaced cellulose as the fiber source. A high SO (HSO) series was also formed by increasing the SO level from 40 g/kg in the basal series to 100 g/kg. Thus the LCF series was concurrently classified as low SO (LSO) series to control SO effect. Each of the eventual 9 diets were fed to 5 floor pens of ten 65-day-old ducks. Ileal AA flow was measured after a 5 day feeding period in both experiments. Linear regression was calculated between ileal flow and dietary intake of individual AA. The IEIF interpreted as the y-intercept of each linear function responded neither to elevated ingestion of each CF type nor to SO level. Age and DMI had no effect on IEIF computed in relation to BW, but wide discrepancies resulted when related to DMI. Overall IEIF of AA varied between 14.3 to 129.8 mg/kg BW d-1. These flows were established in model computations to account for 10 to 64% of the recommended intake of limiting AA. In conclusion the ileal inevitable flow is constant within the dietary/age conditions investigated. However it is modulated by feed intake and accounts for a significant portion of total amino acid requirement. © 2017 Poultry Science Association Inc.

  19. Accumulation of N and P in the Legume Lespedeza davurica in Controlled Mixtures with the Grass Bothriochloa ischaemum under Varying Water and Fertilization Conditions.

    Science.gov (United States)

    Xu, Bingcheng; Xu, Weizhou; Wang, Zhi; Chen, Zhifei; Palta, Jairo A; Chen, Yinglong

    2018-01-01

    Water and fertilizers affect the nitrogen (N) and phosphorus (P) acquisition and allocation among organs in dominant species in natural vegetation on the semiarid Loess Plateau. This study aimed to clarify the N and P accumulation and N:P ratio at organ and plant level of a local legume species mixed with a grass species under varying water and fertilizer supplies, and thus to fully understand the requirements and balance of nutrient elements in response to growth conditions change of native species. The N and P concentration in the organ (leaf, stem, and root) and plant level of Lespedeza davurica (C 3 legume), were examined when intercropped with Bothriochloa ischaemum (C 4 grass). The two species were grown outdoors in pots under 80, 60, and 40% of soil water field capacity (FC), -NP, +N, +P, and +NP supply and the grass:legume mixture ratios of 2:10, 4:8, 6:6, 8:4, 10:2, and 12:0. The three set of treatments were under a randomized complete block design. Intercropping with B. ischaemum did not affect N concentrations in leaf, stem and root of L. davurica , but reduced P concentration in each organ under P fertilization. Only leaf N concentration in L. davurica showed decreasing trend as soil water content decreased under all fertilization and mixture proportion treatments. Stems had the lowest, while roots had the highest N and P concentration. As the mixture proportion of L. davurica decreased under P fertilization, P concentration in leaf and root also decreased. The N concentration in L. davurica at the whole plant level was 11.1-17.2%. P fertilization improved P concentration, while decreased N:P ratio in L. davurica . The N:P ratios were less than 14.0 under +P and +NP treatments. Our results implied that exogenous N and P fertilizer application may change the N:P stoichiometry and influence the balance between nutrients and organs of native dominant species in natural grassland, and P element should be paid more attention when considering rehabilitating

  20. Accumulation of N and P in the Legume Lespedeza davurica in Controlled Mixtures with the Grass Bothriochloa ischaemum under Varying Water and Fertilization Conditions

    Directory of Open Access Journals (Sweden)

    Bingcheng Xu

    2018-02-01

    Full Text Available Water and fertilizers affect the nitrogen (N and phosphorus (P acquisition and allocation among organs in dominant species in natural vegetation on the semiarid Loess Plateau. This study aimed to clarify the N and P accumulation and N:P ratio at organ and plant level of a local legume species mixed with a grass species under varying water and fertilizer supplies, and thus to fully understand the requirements and balance of nutrient elements in response to growth conditions change of native species. The N and P concentration in the organ (leaf, stem, and root and plant level of Lespedeza davurica (C3 legume, were examined when intercropped with Bothriochloa ischaemum (C4 grass. The two species were grown outdoors in pots under 80, 60, and 40% of soil water field capacity (FC, -NP, +N, +P, and +NP supply and the grass:legume mixture ratios of 2:10, 4:8, 6:6, 8:4, 10:2, and 12:0. The three set of treatments were under a randomized complete block design. Intercropping with B. ischaemum did not affect N concentrations in leaf, stem and root of L. davurica, but reduced P concentration in each organ under P fertilization. Only leaf N concentration in L. davurica showed decreasing trend as soil water content decreased under all fertilization and mixture proportion treatments. Stems had the lowest, while roots had the highest N and P concentration. As the mixture proportion of L. davurica decreased under P fertilization, P concentration in leaf and root also decreased. The N concentration in L. davurica at the whole plant level was 11.1–17.2%. P fertilization improved P concentration, while decreased N:P ratio in L. davurica. The N:P ratios were less than 14.0 under +P and +NP treatments. Our results implied that exogenous N and P fertilizer application may change the N:P stoichiometry and influence the balance between nutrients and organs of native dominant species in natural grassland, and P element should be paid more attention when considering

  1. Regional scenario building as a tool to support vulnerability assessment of food & water security and livelihood conditions under varying natural resources managements

    Science.gov (United States)

    Reinhardt, Julia; Liersch, Stefan; Dickens, Chris; Kabaseke, Clovis; Mulugeta Lemenih, Kassaye; Sghaier, Mongi; Hattermann, Fred

    2013-04-01

    Participatory regional scenario building was carried out with stakeholders and local researchers in four meso-scale case studies (CS) in Africa. In all CS the improvement of food and / or water security and livelihood conditions was identified as the focal issue. A major concern was to analyze the impacts of different plausible future developments on these issues. The process of scenario development is of special importance as it helps to identify main drivers, critical uncertainties and patterns of change. Opportunities and constraints of actors and actions become clearer and reveal adaptation capacities. Effective strategies must be furthermore reasonable and accepted by local stakeholders to be implemented. Hence, developing scenarios and generating strategies need the integration of local knowledge. The testing of strategies shows how they play out in different scenarios and how robust they are. Reasons and patterns of social and natural vulnerability can so be shown. The scenario building exercise applied in this study is inspired by the approach from Peter Schwartz. It aims at determining critical uncertainties and to identify the most important driving forces for a specific focal issue which are likely to shape future developments of a region. The most important and uncertain drivers were analyzed and systematized with ranking exercises during meetings with local researchers and stakeholders. Cause-effect relationships were drawn in the form of concept maps either during the meetings or by researchers based on available information. Past observations and the scenario building outcomes were used to conduct a trend analysis. Cross-comparisons were made to find similarities and differences between CS in terms of main driving forces, patterns of change, opportunities and constraints. Driving forces and trends which aroused consistently over scenarios and CS were identified. First results indicate that livelihood conditions of people rely often directly on the

  2. Consideration of loading conditions initiated by thermal transients in PWR pressure vessels

    International Nuclear Information System (INIS)

    Azodi; Glahn; Kersting; Schulz; Jansky.

    1983-01-01

    This report describes the present state of PWR-plants in the Federal Republic of Germany with respect to - the design of the primary pressure boundary - the analysis of thermal transients and resulting loads - the material conditions and neutron fluence - the requirements for protection against fast fracture. The experimental and analytical research and development programs are delineated together with some foreign R and D programs. It is shown that the parameters investigated (loading condition, crack shape and orientation etc.) cover a broad range. Extensive analytical investigations are emphasized. (orig./RW) [de

  3. Initial conditions for cosmological N-body simulations of the scalar sector of theories of Newtonian, Relativistic and Modified Gravity

    International Nuclear Information System (INIS)

    Valkenburg, Wessel; Hu, Bin

    2015-01-01

    We present a description for setting initial particle displacements and field values for simulations of arbitrary metric theories of gravity, for perfect and imperfect fluids with arbitrary characteristics. We extend the Zel'dovich Approximation to nontrivial theories of gravity, and show how scale dependence implies curved particle paths, even in the entirely linear regime of perturbations. For a viable choice of Effective Field Theory of Modified Gravity, initial conditions set at high redshifts are affected at the level of up to 5% at Mpc scales, which exemplifies the importance of going beyond Λ-Cold Dark Matter initial conditions for modifications of gravity outside of the quasi-static approximation. In addition, we show initial conditions for a simulation where a scalar modification of gravity is modelled in a Lagrangian particle-like description. Our description paves the way for simulations and mock galaxy catalogs under theories of gravity beyond the standard model, crucial for progress towards precision tests of gravity and cosmology

  4. FORSIM, Solution of Ordinary or Partial Differential Equation with Initial Conditions

    International Nuclear Information System (INIS)

    Carver, M.B.

    1985-01-01

    1 - Description of problem or function: FORSIM is a FORTRAN oriented simulation program which automates the continuous transient solution of systems of ordinary and/or partial differential equations. The user writes his equations in a FORTRAN subroutine, following prescribed rules, and loads this routine along with the executive routines. The executive routines then read in initial data supplied by the user and proceed with the integration. 2 - Method of solution: Partial differential equations are converted to coupled ordinary differential equations by suitable discretization formulae. Integration is done by variable order, variable step-size error controlled algorithms. 3 - Restrictions on the complexity of the problem - Maximum of: 1000 ordinary differential equations

  5. Study on light water reactor fuel behavior under reactivity initiated accident condition in TREAT

    International Nuclear Information System (INIS)

    Ohnishi, Nobuaki; Ishijima, Kiyomi; Ochiai, Masaaki; Tanzawa, Sadamitsu; Uemura, Mutsumi

    1981-05-01

    This report reviews the results of the fuel failure experiments performed in TREAT in the U.S.A. simulating Reactivity Initiated Accidents. One of the main purposes of the TREAT experiments is the study of the fuel failure behavior, and the other is the study of the molten fuel-water coolant interaction and the consequent hydrogen behavior. This report mainly shows the results of the TREAT experiments studying the fuel failure behavior in Light Water Reactor, and then it describes the fuel failure threshold and the fuel failure mechanism, considering the results of the photographic experiments of the fuel failure behavior with transparent capsules. (author)

  6. On the stochastic approach to inflation and the initial conditions in the universe

    International Nuclear Information System (INIS)

    Pollock, M.D.

    1986-05-01

    By applying stochastic methods to a theory in which a potential V(Φ) causes a period of quasi-expansion of the universe, Starobinsky has derived an expression for the probability distribution P(V) appropriate to chaotic inflation in the classical approximation. We obtain the corresponding expression for a broken-symmetry theory of gravity. For the Coleman-Weinberg potential, it appears most probable that the initial value of Φ is Φ i O , in which case inflation occurs naturally, because V(Φ i )>O

  7. The effect of initial conditions on the electromagnetic radiation generation in type III solar radio bursts

    International Nuclear Information System (INIS)

    Schmitz, H.; Tsiklauri, D.

    2013-01-01

    Extensive particle-in-cell simulations of fast electron beams injected in a background magnetised plasma with a decreasing density profile were carried out. These simulations were intended to further shed light on a newly proposed mechanism for the generation of electromagnetic waves in type III solar radio bursts [D. Tsiklauri, Phys. Plasmas, 18, 052903 (2011)]. The numerical simulations were carried out using different density profiles and fast electron distribution functions. It is shown that electromagnetic L and R modes are excited by the transverse current, initially imposed on the system. In the course of the simulations, no further interaction of the electron beam with the background plasma could be observed

  8. Entropy Growth in the Early Universe and Confirmation of Initial Big Bang Conditions

    Science.gov (United States)

    Beckwith, Andrew

    2009-09-01

    This paper shows how increased entropy values from an initially low big bang level can be measured experimentally by counting relic gravitons. Furthermore the physical mechanism of this entropy increase is explained via analogies with early-universe phase transitions. The role of Jack Ng's (2007, 2008a, 2008b) revised infinite quantum statistics in the physics of gravitational wave detection is acknowledged. Ng's infinite quantum statistics can be used to show that ΔS~ΔNgravitons is a startmg point to the increasing net universe cosmological entropy. Finally, in a nod to similarities AS ZPE analysis, it is important to note that the resulting ΔS~ΔNgravitons ≠ 1088, that in fact it is much lower, allowing for evaluating initial graviton production as an emergent field phenomena, which may be similar to how ZPE states can be used to extract energy from a vacuum if entropy is not maximized. The rapid increase in entropy so alluded to without near sudden increases to 1088 may be enough to allow successful modeling of relic graviton production for entropy in a manner similar to ZPE energy extraction from a vacuum state.

  9. Lack of anomalous diffusion in linear translationally-invariant systems determined by only one initial condition

    International Nuclear Information System (INIS)

    Khorrami, Mohammad; Shariati, Ahmad; Aghamohammadi, Amir; Fatollahi, Amir H.

    2012-01-01

    It is shown that as far as the linear diffusion equation meets both time- and space-translational invariance, the time dependence of a moment of degree α is a polynomial of degree at most equal to α, while all connected moments are at most linear functions of time. As a special case, the variance is an at most linear function of time. -- Highlights: ► The sufficient conditions for having the non-anomalous diffusion are given. ► Conditions are linearity, space-time translation invariance, solution uniqueness. ► Some versions of the fractional derivatives lack the translational invariance. ► It is shown the encoded inhomogeneity in derivatives causes anomalous behavior.

  10. Lack of anomalous diffusion in linear translationally-invariant systems determined by only one initial condition

    Energy Technology Data Exchange (ETDEWEB)

    Khorrami, Mohammad, E-mail: mamwad@mailaps.org [Department of Physics, Alzahra University, Tehran 19938-93973 (Iran, Islamic Republic of); Shariati, Ahmad, E-mail: shariati@mailaps.org [Department of Physics, Alzahra University, Tehran 19938-93973 (Iran, Islamic Republic of); Aghamohammadi, Amir, E-mail: mohamadi@alzahra.ac.ir [Department of Physics, Alzahra University, Tehran 19938-93973 (Iran, Islamic Republic of); Fatollahi, Amir H., E-mail: ahfatol@gmail.com [Department of Physics, Alzahra University, Tehran 19938-93973 (Iran, Islamic Republic of)

    2012-01-16

    It is shown that as far as the linear diffusion equation meets both time- and space-translational invariance, the time dependence of a moment of degree α is a polynomial of degree at most equal to α, while all connected moments are at most linear functions of time. As a special case, the variance is an at most linear function of time. -- Highlights: ► The sufficient conditions for having the non-anomalous diffusion are given. ► Conditions are linearity, space-time translation invariance, solution uniqueness. ► Some versions of the fractional derivatives lack the translational invariance. ► It is shown the encoded inhomogeneity in derivatives causes anomalous behavior.

  11. Surface conditioning with Escherichia coli cell wall components can reduce biofilm formation by decreasing initial adhesion

    Directory of Open Access Journals (Sweden)

    Luciana C. Gomes

    2017-07-01

    Full Text Available Bacterial adhesion and biofilm formation on food processing surfaces pose major risks to human health. Non-efficient cleaning of equipment surfaces and piping can act as a conditioning layer that affects the development of a new biofilm post-disinfection. We have previously shown that surface conditioning with cell extracts could reduce biofilm formation. In the present work, we hypothesized that E. coli cell wall components could be implicated in this phenomena and therefore mannose, myristic acid and palmitic acid were tested as conditioning agents. To evaluate the effect of surface conditioning and flow topology on biofilm formation, assays were performed in agitated 96-well microtiter plates and in a parallel plate flow chamber (PPFC, both operated at the same average wall shear stress (0.07 Pa as determined by computational fluid dynamics (CFD. It was observed that when the 96-well microtiter plate and the PPFC were used to form biofilms at the same shear stress, similar results were obtained. This shows that the referred hydrodynamic feature may be a good scale-up parameter from high-throughput platforms to larger scale flow cell systems as the PPFC used in this study. Mannose did not have any effect on E. coli biofilm formation, but myristic and palmitic acid inhibited biofilm development by decreasing cell adhesion (in about 50%. These results support the idea that in food processing equipment where biofilm formation is not critical below a certain threshold, bacterial lysis and adsorption of cell components to the surface may reduce biofilm buildup and extend the operational time.

  12. Determination of initial conditions for heat exchanger placed in furnace by burning pellets

    Science.gov (United States)

    Durčanský, Peter; Jandačka, Jozef; Kapjor, Andrej

    2014-08-01

    Objective of the experimental facility and subsequent measurements is generally determine whether the expected physical properties of the verification, identification of the real behavior of the proposed system, or part thereof. For the design of heat exchanger for combined energy machine is required to identify and verify a large number of parameters. One of these are the boundary conditions of heat exchanger and pellets burner.

  13. INITIATORS AND TRIGGERING CONDITIONS FOR ADAPTIVE AUTOMATION IN ADVANCED SMALL MODULAR REACTORS

    Energy Technology Data Exchange (ETDEWEB)

    Katya L Le Blanc; Johanna h Oxstrand

    2014-04-01

    It is anticipated that Advanced Small Modular Reactors (AdvSMRs) will employ high degrees of automation. High levels of automation can enhance system performance, but often at the cost of reduced human performance. Automation can lead to human out-of the loop issues, unbalanced workload, complacency, and other problems if it is not designed properly. Researchers have proposed adaptive automation (defined as dynamic or flexible allocation of functions) as a way to get the benefits of higher levels of automation without the human performance costs. Adaptive automation has the potential to balance operator workload and enhance operator situation awareness by allocating functions to the operators in a way that is sensitive to overall workload and capabilities at the time of operation. However, there still a number of questions regarding how to effectively design adaptive automation to achieve that potential. One of those questions is related to how to initiate (or trigger) a shift in automation in order to provide maximal sensitivity to operator needs without introducing undesirable consequences (such as unpredictable mode changes). Several triggering mechanisms for shifts in adaptive automation have been proposed including: operator initiated, critical events, performance-based, physiological measurement, model-based, and hybrid methods. As part of a larger project to develop design guidance for human-automation collaboration in AdvSMRs, researchers at Idaho National Laboratory have investigated the effectiveness and applicability of each of these triggering mechanisms in the context of AdvSMR. Researchers reviewed the empirical literature on adaptive automation and assessed each triggering mechanism based on the human-system performance consequences of employing that mechanism. Researchers also assessed the practicality and feasibility of using the mechanism in the context of an AdvSMR control room. Results indicate that there are tradeoffs associated with each

  14. Relation Between Initial Cosmological Conditions and the Properties of Dark Matter Haloes

    International Nuclear Information System (INIS)

    Semenov, Vadim

    2013-01-01

    The core-cusp problem is one of the essential issues in modern cosmology. The Entropy Theory of haloes Evolution recently suggested by Lukash, Doroshkevich and Mikheeva is one of the possible solutions to this problem. This work compares some results of numerical simulation of Large-Scale Structure with the conclusions of the Entropy Theory in order to verify this theory. The numerical simulation was performed in a volume 100 Mpc/h in a side using ∼ 17 million particles. Dark matter particles, which then form virialized haloes, were found in the initial perturbation field. This work investigates the distribution of these dark matter particles and measures the velocity dispersion profiles. It also traces evolution of haloes entropy profiles. On the whole, simulation results correspond to Entropy Theory of haloes evolution

  15. Incidence of WHO stage 3 and 4 conditions following initiation of anti-retroviral therapy in resource limited settings.

    Directory of Open Access Journals (Sweden)

    Andrea J Curtis

    Full Text Available OBJECTIVES: To determine the incidence of WHO clinical stage 3 and 4 conditions during early anti-retroviral therapy (ART in resource limited settings (RLS. DESIGN/SETTING: A descriptive analysis of routine program data collected prospectively from 25 Médecins Sans Frontières supported HIV treatment programs in eight countries between 2002 and 2010. SUBJECTS/PARTICIPANTS: 35,349 study participants with median follow-up on ART of 1.33 years (IQR 0.51-2.41. OUTCOME MEASURES: Incidence in 100 person-years of WHO stage 3 or 4 conditions during 5 periods after ART initiation. Diagnoses of conditions were made according to WHO criteria and relied upon clinical assessments supported by basic laboratory investigations. RESULTS: The incidence of any WHO clinical stage 3 or 4 condition over 3 years was 40.02 per 100 person-years (31.77 for stage 3 and 8.25 for stage 4. The incidence of stage 3 and 4 conditions fell by over 97% between months 0-3 and months 25-36 (77.81 to 2.40 for stage 3 and 28.70 to 0.64 for stage 4. During months 0-3 pulmonary tuberculosis was the most common condition diagnosed in adults (incidence 22.24 per 100 person-years and children aged 5-14 years (25.76 and oral candidiasis was the most common in children <5 years (25.79. Overall incidences were higher in Africa compared with Asia (43.98 versus 12.97 for stage 3 and 8.98 versus 7.05 for stage 4 conditions, p<0.001. Pulmonary tuberculosis, weight loss, oral and oesophageal candidiasis, chronic diarrhoea, HIV wasting syndrome and severe bacterial infections were more common in Africa. Extra-pulmonary tuberculosis, non-tuberculous mycobacterial infection, cryptococcosis, penicilliosis and toxoplasmosis were more common in Asia. CONCLUSIONS: The incidence of WHO stage 3 and 4 conditions during the early period after ART initiation in RLS is high, but greatly reduces over time. This is likely due to both the benefits of ART and deaths of the sickest patients occurring shortly

  16. Evaluation of optimization strategies and the effect of initial conditions on IMAT optimization using a leaf position optimization algorithm

    International Nuclear Information System (INIS)

    Oliver, Mike; Jensen, Michael; Chen, Jeff; Wong, Eugene

    2009-01-01

    Intensity-modulated arc therapy (IMAT) is a rotational variant of intensity-modulated radiation therapy (IMRT) that can be implemented with or without angular dose rate variation. The purpose of this study is to assess optimization strategies and initial conditions using a leaf position optimization (LPO) algorithm altered for variable dose rate IMAT. A concave planning target volume (PTV) with a central cylindrical organ at risk (OAR) was used in this study. The initial IMAT arcs were approximated by multiple static beams at 5 deg. angular increments where multi-leaf collimator (MLC) leaf positions were determined from the beam's eye view to irradiate the PTV but avoid the OAR. For the optimization strategy, two arcs with arc ranges of 280 deg. and 150 deg. were employed and plans were created using LPO alone, variable dose rate optimization (VDRO) alone, simultaneous LPO and VDRO and sequential combinations of these strategies. To assess the MLC initialization effect, three single 360 deg. arc plans with different initial MLC configurations were generated using the simultaneous LPO and VDRO. The effect of changing optimization degrees of freedom was investigated by employing 3 deg., 5 deg. and 10 deg. angular sampling intervals for the two 280 deg., two 150 deg. and single arc plans using LPO and VDRO. The objective function value, a conformity index, a dose homogeneity index, mean dose to OAR and normal tissues were computed and used to evaluate the treatment plans. This study shows that the best optimization strategy for a concave target is to use simultaneous MLC LPO and VDRO. We found that the optimization result is sensitive to the choice of initial MLC aperture shapes suggesting that an LPO-based IMAT plan may not be able to overcome local minima for this geometry. In conclusion, simultaneous MLC leaf position and VDRO are needed with the most appropriate initial conditions (MLC positions, arc ranges and number of arcs) for IMAT.

  17. Robust Initial Wetness Condition Framework of an Event-Based Rainfall–Runoff Model Using Remotely Sensed Soil Moisture

    OpenAIRE

    Wooyeon Sunwoo; Minha Choi

    2017-01-01

    Runoff prediction in limited-data areas is vital for hydrological applications, such as the design of infrastructure and flood defenses, runoff forecasting, and water management. Rainfall–runoff models may be useful for simulation of runoff generation, particularly event-based models, which offer a practical modeling scheme because of their simplicity. However, there is a need to reduce the uncertainties related to the estimation of the initial wetness condition (IWC) prior to a rainfall even...

  18. Radiographic detection of initial carious lesions on the proximal surfaces of teeth. Part I. The influence of exposure conditions

    International Nuclear Information System (INIS)

    Arnold, L.V.

    1987-01-01

    The relationship between a number of technical exposure conditions and the diagnostic value of bitewing radiographs in the interpretation of initial proximal carious lesions was evaluated. The most important exposure factors for radiographs are tube voltage, filtration, and exposure time. Tube voltage and filtration were found to have an insignificant influence on the diagnostic quality. Exposure time proved to be the most critical factor in influencing diagnostic quality. The greatest difference in diagnostic quality, however, was caused by differences between observers

  19. Hydrides blister formation and induced embrittlement on zircaloy-4 cladding tubes in reactivity initiated conditions

    International Nuclear Information System (INIS)

    Hellouin-De-Menibus, A.

    2012-01-01

    Our aim is to study the cladding fracture with mechanical tests more representative of RIA conditions, taking into account the hydrides blisters, representative strain rates and stress states. To obtain hydride blisters, we developed a thermodiffusion setup that reproduces blister growth in reactor conditions. By metallography, nano-hardness, XRD and ERDA, we showed that they are constituted by 80% to 100% of δ hydrides in a Zircaloy-4 matrix, and that the zirconium beneath has some radially oriented hydrides. We modeled the blister growth kinetics taking into account the hysteresis of the hydrogen solubility limit and defined the thermal gradient threshold for blister growth. The modeling of the dilatometric behavior of hydrided zirconium indicates the important role of the material crystallographic texture, which could explain differences in the blister shape. Mechanical tests monitored with an infrared camera showed that significant local heating occurred at strain rates higher than 0.1/s. In parallel, the Expansion Due to Compression test was optimized to increase the bi-axiality level from uniaxial stress to plane strain (HB-EDC and VHB-EDC tests). This increase in loading bi-axiality lowers greatly the fracture strain at 25 C and 350 C only in homogeneous material without blister. Eventually, the ductility decrease of unirradiated Zircaloy-4 cladding tube in function of the blister depth was quantified. (author) [fr

  20. Effects of Heterogeneity and Uncertainties in Sources and Initial and Boundary Conditions on Spatiotemporal Variations of Groundwater Levels

    Science.gov (United States)

    Zhang, Y. K.; Liang, X.

    2014-12-01

    Effects of aquifer heterogeneity and uncertainties in source/sink, and initial and boundary conditions in a groundwater flow model on the spatiotemporal variations of groundwater level, h(x,t), were investigated. Analytical solutions for the variance and covariance of h(x, t) in an unconfined aquifer described by a linearized Boussinesq equation with a white noise source/sink and a random transmissivity field were derived. It was found that in a typical aquifer the error in h(x,t) in early time is mainly caused by the random initial condition and the error reduces as time goes to reach a constant error in later time. The duration during which the effect of the random initial condition is significant may last a few hundred days in most aquifers. The constant error in groundwater in later time is due to the combined effects of the uncertain source/sink and flux boundary: the closer to the flux boundary, the larger the error. The error caused by the uncertain head boundary is limited in a narrow zone near the boundary but it remains more or less constant over time. The effect of the heterogeneity is to increase the variation of groundwater level and the maximum effect occurs close to the constant head boundary because of the linear mean hydraulic gradient. The correlation of groundwater level decreases with temporal interval and spatial distance. In addition, the heterogeneity enhances the correlation of groundwater level, especially at larger time intervals and small spatial distances.

  1. Divergent series and memory of the initial condition in the long-time solution of some anomalous diffusion problems.

    Science.gov (United States)

    Yuste, S Bravo; Borrego, R; Abad, E

    2010-02-01

    We consider various anomalous d -dimensional diffusion problems in the presence of an absorbing boundary with radial symmetry. The motion of particles is described by a fractional diffusion equation. Their mean-square displacement is given by r(2) proportional, variant t(gamma)(0divergent series appear when the concentration or survival probabilities are evaluated via the method of separation of variables. While the solution for normal diffusion problems is, at most, divergent as t-->0 , the emergence of such series in the long-time domain is a specific feature of subdiffusion problems. We present a method to regularize such series, and, in some cases, validate the procedure by using alternative techniques (Laplace transform method and numerical simulations). In the normal diffusion case, we find that the signature of the initial condition on the approach to the steady state rapidly fades away and the solution approaches a single (the main) decay mode in the long-time regime. In remarkable contrast, long-time memory of the initial condition is present in the subdiffusive case as the spatial part Psi1(r) describing the long-time decay of the solution to the steady state is determined by a weighted superposition of all spatial modes characteristic of the normal diffusion problem, the weight being dependent on the initial condition. Interestingly, Psi1(r) turns out to be independent of the anomalous diffusion exponent gamma .

  2. Dynamics of leaf and spikelet primordia initiation in wheat as affected by Ppd-1a alleles under field conditions.

    Science.gov (United States)

    Ochagavía, Helga; Prieto, Paula; Savin, Roxana; Griffiths, Simon; Slafer, GustavoA

    2018-04-27

    Wheat adaptation is affected by Ppd genes, but the role of these alleles in the rates of leaf and spikelet initiation has not been properly analysed. Twelve near isogenic lines (NILs) combining Ppd-1a alleles from different donors introgressed in A, B, and/or D genomes were tested under field conditions during two growing seasons together with the wild type, Paragon. Leaf initiation rate was unaffected by Ppd-1a alleles so the final leaf number (FLN) was reduced in parallel with reductions in the duration of the vegetative phase. Spikelet primordia initiation was accelerated and consequently the effect on spikelets per spike was less than proportional to the effect on the duration of spikelet initiation. The magnitude of these effects on spikelet plastochron depended on the doses of Ppd-1 homoeoalleles and the specific insensitivity alleles carried. Double ridge was consistently later than floral initiation, but the difference between them was not affected by Ppd-1a alleles. These findings have potential for selecting the best combinations from the Ppd-1 homoeoallelic series for manipulating adaptation taking into consideration particular effects on spikelet number.

  3. Experimental characterization of initial conditions and spatio-temporal evolution of a small Atwood number Rayleigh-Taylor mixing layer

    Energy Technology Data Exchange (ETDEWEB)

    Mueschke, N J; Andrews, M J; Schilling, O

    2005-09-26

    The initial multi-mode interfacial velocity and density perturbations present at the onset of a small Atwood number, incompressible, miscible, Rayleigh-Taylor instability-driven mixing layer have been quantified using a combination of experimental techniques. The streamwise interfacial and spanwise interfacial perturbations were measured using high-resolution thermocouples and planar laser-induced fluorescence (PLIF), respectively. The initial multi-mode streamwise velocity perturbations at the two-fluid density interface were measured using particle-image velocimetry (PIV). It was found that the measured initial conditions describe an initially anisotropic state, in which the perturbations in the streamwise and spanwise directions are independent of one another. The evolution of various fluctuating velocity and density statistics, together with velocity and density variance spectra, were measured using PIV and high-resolution thermocouple data. The evolution of the velocity and density statistics is used to investigate the early-time evolution and the onset of strongly-nonlinear, transitional dynamics within the mixing layer. The early-time evolution of the density and vertical velocity variance spectra indicate that velocity fluctuations are the dominant mechanism driving the instability development. The implications of the present experimental measurements on the initialization of Reynolds-averaged turbulent transport and mixing models and of direct and large-eddy simulations of Rayleigh-Taylor instability-induced turbulence are discussed.

  4. Improvement of initial vacuum condition along 2008-2010 KSTAR campaign by vessel baking

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kwang Pyo, E-mail: kpkim@nfri.er.ke [National Fusion Research Institute, Gwahagno 113, Daejeon 305-333 (Korea, Republic of); Hong, S.H.; Jung, N.Y.; Kim, S.T.; Kim, H.T.; Lee, K.S.; Kim, K.M.; Bang, E.N.; Chang, Y.B.; Kim, H.K.; Chu, Y.; Kim, Y.O.; Park, S.H.; Woo, I.S.; Hong, J.S.; Kim, S.W.; Park, K.R.; Na, H.K.; Yang, H.L.; Kim, Y.S. [National Fusion Research Institute, Gwahagno 113, Daejeon 305-333 (Korea, Republic of)

    2011-10-15

    Korea Superconducting Tokamak Advanced Research (KSTAR) is upgraded for its KSTAR 3rd campaign for new target mission to produce the D-shaped plasma with a target plasma current of 500 kA and/or pulse length of 5 s. New Plasma Facing Components (PFCs) are installed which leads to the increase of the surface area of the vessel by a factor of about 5. The vacuum conditioning such as the vessel baking has been performed in order to remove various kinds of impurities including H{sub 2}O, carbon and oxygen for the plasma. The total outgassing rate in the KSTAR 1st campaign was measured as 1.5 x 10{sup -4} mbar l s{sup -1} which is increased by a factor of 3 (6.49 x 10{sup -4} mbar l s{sup -1}) in the KSTAR 3rd campaign. Nevertheless, the outgassing rates per unit area have been decreased from 9.31 x 10{sup -5} mbar l m{sup -2} s{sup -1} to 1.22 x 10{sup -5} mbar l m{sup -2} s{sup -1} due to the upgrade of baking system and series of baking operation.

  5. Improvement of initial vacuum condition along 2008-2010 KSTAR campaign by vessel baking

    International Nuclear Information System (INIS)

    Kim, Kwang Pyo; Hong, S.H.; Jung, N.Y.; Kim, S.T.; Kim, H.T.; Lee, K.S.; Kim, K.M.; Bang, E.N.; Chang, Y.B.; Kim, H.K.; Chu, Y.; Kim, Y.O.; Park, S.H.; Woo, I.S.; Hong, J.S.; Kim, S.W.; Park, K.R.; Na, H.K.; Yang, H.L.; Kim, Y.S.

    2011-01-01

    Korea Superconducting Tokamak Advanced Research (KSTAR) is upgraded for its KSTAR 3rd campaign for new target mission to produce the D-shaped plasma with a target plasma current of 500 kA and/or pulse length of 5 s. New Plasma Facing Components (PFCs) are installed which leads to the increase of the surface area of the vessel by a factor of about 5. The vacuum conditioning such as the vessel baking has been performed in order to remove various kinds of impurities including H 2 O, carbon and oxygen for the plasma. The total outgassing rate in the KSTAR 1st campaign was measured as 1.5 x 10 -4 mbar l s -1 which is increased by a factor of 3 (6.49 x 10 -4 mbar l s -1 ) in the KSTAR 3rd campaign. Nevertheless, the outgassing rates per unit area have been decreased from 9.31 x 10 -5 mbar l m -2 s -1 to 1.22 x 10 -5 mbar l m -2 s -1 due to the upgrade of baking system and series of baking operation.

  6. Autolytic degradation of skipjack tuna during heating as affected by initial quality and processing conditions.

    Science.gov (United States)

    Stagg, Nicola J; Amato, Penny M; Giesbrecht, Francis; Lanier, Tyre C

    2012-02-01

    Several factors were studied as affecting protein degradation and texture of skipjack tuna muscle following ambient pressure thermal processing (precooking). These included degree of mushy tuna syndrome (MTS) evidenced in the raw meat, raw meat pH, abusive thawing/holding, and precooking temperature/time. Slurries and intact pieces from frozen skipjack tuna, either tempered for 2 h or thawed and held at 25 °C for 22 h (abusive treatment) were heated at temperatures ranging from 40 to 80 °C for up to 2 h, and also at 90 °C for 1 h, with or without prior adjustment of pH to 5 or 7 to favor cathepsin or calpain activity, respectively. Proteolysis of precooked samples was monitored by Lowry assay and SDS-PAGE; cooked texture of intact meat was measured using a Kramer shear press and by sensory profile analysis. Proteolysis maximally occurred in slurries of skipjack tuna muscle that had been abusively stored (22 h at 25 °C) and adjusted to pH 5 prior to heating at 55 °C. Intact pieces of tuna abusively thawed/held for 22 h with subsequent heating at 55 °C also evidenced the most proteolysis and were the least firm in texture. Raw fish that evidenced higher severity of MTS when raw displayed higher levels of proteolysis prior to cooking, which were further increased after cooking at 55 °C. The kinetic data presented here can be used to optimize processing conditions for skipjack tuna canning to minimize textural degradation and optimize quality. © 2012 Institute of Food Technologists®

  7. Simulation of Electrical Discharge Initiated by a Nanometer-Sized Probe in Atmospheric Conditions

    International Nuclear Information System (INIS)

    Chen Ran; Chen Chilai; Liu Youjiang; Wang Huanqin; Kong Deyi; Ma Yuan; Cada Michael; Brugger Jürgen

    2013-01-01

    In this paper, a two-dimensional nanometer scale tip-plate discharge model has been employed to study nanoscale electrical discharge in atmospheric conditions. The field strength distributions in a nanometer scale tip-to-plate electrode arrangement were calculated using the finite element analysis (FEA) method, and the influences of applied voltage amplitude and frequency as well as gas gap distance on the variation of effective discharge range (EDR) on the plate were also investigated and discussed. The simulation results show that the probe with a wide tip will cause a larger effective discharge range on the plate; the field strength in the gap is notably higher than that induced by the sharp tip probe; the effective discharge range will increase linearly with the rise of excitation voltage, and decrease nonlinearly with the rise of gap length. In addition, probe dimension, especially the width/height ratio, affects the effective discharge range in different manners. With the width/height ratio rising from 1:1 to 1:10, the effective discharge range will maintain stable when the excitation voltage is around 50 V. This will increase when the excitation voltage gets higher and decrease as the excitation voltage gets lower. Furthermore, when the gap length is 5 nm and the excitation voltage is below 20 V, the diameter of EDR in our simulation is about 150 nm, which is consistent with the experiment results reported by other research groups. Our work provides a preliminary understanding of nanometer scale discharges and establishes a predictive structure-behavior relationship

  8. Evaluating the influence of initial magnetization conditions on extracted exchange parameters in NMR relaxation experiments: applications to CPMG and CEST

    Energy Technology Data Exchange (ETDEWEB)

    Yuwen, Tairan; Sekhar, Ashok; Kay, Lewis E., E-mail: kay@pound.med.utoronto.ca [The University of Toronto, Departments of Molecular Genetics, Biochemistry and Chemistry (Canada)

    2016-08-15

    Transient excursions of native protein states to functionally relevant higher energy conformations often occur on the μs–ms timescale. NMR spectroscopy has emerged as an important tool to probe such processes using techniques such as Carr–Purcell–Meiboom–Gill (CPMG) relaxation dispersion and Chemical Exchange Saturation Transfer (CEST). The extraction of kinetic and structural parameters from these measurements is predicated upon mathematical modeling of the resulting relaxation profiles, which in turn relies on knowledge of the initial magnetization conditions at the start of the CPMG/CEST relaxation elements in these experiments. Most fitting programs simply assume initial magnetization conditions that are given by equilibrium populations, which may be incorrect in certain implementations of experiments. In this study we have quantified the systematic errors in extracted parameters that are generated from analyses of CPMG and CEST experiments using incorrect initial boundary conditions. We find that the errors in exchange rates (k{sub ex}) and populations (p{sub E}) are typically small (<10 %) and thus can be safely ignored in most cases. However, errors become larger and cannot be fully neglected (20–40 %) as k{sub ex} falls near the lower limit of each method or when short CPMG/CEST relaxation elements are used in these experiments. The source of the errors can be rationalized and their magnitude given by a simple functional form. Despite the fact that errors tend to be small, it is recommended that the correct boundary conditions be implemented in fitting programs so as to obtain as robust estimates of exchange parameters as possible.

  9. Downscaling Ocean Conditions: Initial Results using a Quasigeostrophic and Realistic Ocean Model

    Science.gov (United States)

    Katavouta, Anna; Thompson, Keith

    2014-05-01

    Previous theoretical work (Henshaw et al, 2003) has shown that the small-scale modes of variability of solutions of the unforced, incompressible Navier-Stokes equation, and Burgers' equation, can be reconstructed with surprisingly high accuracy from the time history of a few of the large-scale modes. Motivated by this theoretical work we first describe a straightforward method for assimilating information on the large scales in order to recover the small scale oceanic variability. The method is based on nudging in specific wavebands and frequencies and is similar to the so-called spectral nudging method that has been used successfully for atmospheric downscaling with limited area models (e.g. von Storch et al., 2000). The validity of the method is tested using a quasigestrophic model configured to simulate a double ocean gyre separated by an unstable mid-ocean jet. It is shown that important features of the ocean circulation including the position of the meandering mid-ocean jet and associated pinch-off eddies can indeed be recovered from the time history of a small number of large-scales modes. The benefit of assimilating additional time series of observations from a limited number of locations, that alone are too sparse to significantly improve the recovery of the small scales using traditional assimilation techniques, is also demonstrated using several twin experiments. The final part of the study outlines the application of the approach using a realistic high resolution (1/36 degree) model, based on the NEMO (Nucleus for European Modelling of the Ocean) modeling framework, configured for the Scotian Shelf of the east coast of Canada. The large scale conditions used in this application are obtained from the HYCOM (HYbrid Coordinate Ocean Model) + NCODA (Navy Coupled Ocean Data Assimilation) global 1/12 degree analysis product. Henshaw, W., Kreiss, H.-O., Ystrom, J., 2003. Numerical experiments on the interaction between the larger- and the small-scale motion of

  10. Artificial boundary conditions for certain evolution PDEs with cubic nonlinearity for non-compactly supported initial data

    Science.gov (United States)

    Vaibhav, V.

    2011-04-01

    The paper addresses the problem of constructing non-reflecting boundary conditions for two types of one dimensional evolution equations, namely, the cubic nonlinear Schrödinger (NLS) equation, ∂tu+Lu-iχ|u|2u=0 with L≡-i∂x2, and the equation obtained by letting L≡∂x3. The usual restriction of compact support of the initial data is relaxed by allowing it to have a constant amplitude along with a linear phase variation outside a compact domain. We adapt the pseudo-differential approach developed by Antoine et al. (2006) [5] for the NLS equation to the second type of evolution equation, and further, extend the scheme to the aforementioned class of initial data for both of the equations. In addition, we discuss efficient numerical implementation of our scheme and produce the results of several numerical experiments demonstrating its effectiveness.

  11. Conditions of Antonin seam exploitation in the open pit Druzba near Sokolov with regard to the protection of thermal and mineral water resources in Karlovy Vary

    International Nuclear Information System (INIS)

    Grmela, A.; Sterba, J.

    1997-01-01

    From new structural-tectonic findings concerning the extent and character of the Nove Sedlo fault in the area of the Druzba open pit in the Sokolov Basin, it is evident that it is a form of listric fault of shallow range, ending in an intermediate slip. This finding has a decisive relevance for deciding as to the current placement of the pit in the protection zone of Karlovy Vary's thermal springs. For the purposes of the exploitation of the Antonin seam, it is necessary to create a network of multipurpose bore holes at the bottom of the pit and in front of the working face for the regulation of pressure in the basal aquifer and to ensure unity of monitoring and its complex evaluation on the basis of numerical modelling of the hydrodynamic state of the basal aquifer and the geotechnical processes of the seam's impermeable bedrock. 4 refs

  12. Tracer Studies to Characterize the Effects of Roadside Noise Barriers on Near-Road Pollutant Dispersion under Varying Atmospheric Stability Conditions

    Science.gov (United States)

    A roadway toxics dispersion study was conducted by the Field Research Division (FRD) of NOAA at the Idaho National Laboratory (INL) near Idaho Falls, ID to document the effects on concentrations of roadway emissions behind a roadside sound barrier in various conditions of atmosph...

  13. Treatment and conditioning of low-level radioactive waste in Belgium: initial operating results of the Cilva facility

    International Nuclear Information System (INIS)

    Monsch, O.; Renard, C.; Deckers, J.; Luycx, P.

    1995-01-01

    The Belgian National Radioactive Waste and Enriched Fissile Material Agency (ONDRAF), which is responsible for the management of all radioactive waste in Belgium, recently decided to commission the CILVA facility. Operation of this facility, which comprises a number of units for the treatment of low-level radwaste, has been contracted to ONDRAF's Belgoprocess subsidiary based at the Dessel site. A consortium comprising SGN and Fabricom was in charge of building the CILVA facility's waste preparation and conditioning (concrete solidification) units. The concrete solidification processes, which were devised and developed by SGN, have been qualified to secure ONDRAF certification of the process and the facility. This enabled active commissioning of the waste conditioning unit in mid-August 1994. Active commissioning of the waste preparation unit was carried out in several stages up to the beginning of 1995 in accordance with operating requirements. Initial operating results of the two units are presented. (author)

  14. Automatically varying the composition of a mixed refrigerant solution for single mixed refrigerant LNG (liquefied natural gas) process at changing working conditions

    International Nuclear Information System (INIS)

    Xu, Xiongwen; Liu, Jinping; Cao, Le; Pang, Weiqiang

    2014-01-01

    The SMR (single mixed refrigerant) process is widely used in the small- and medium-scale liquefaction of NG (natural gas). Operating the MR (mixed-refrigerant) process outside of the design specifications is difficult but essential to save energy. Nevertheless, it is difficult to realize because the process needs to alter the working refrigerant composition. To address this challenge, this study investigated the performance diagnosis mechanism for SMR process. A control strategy was then proposed to control the changes in working refrigerant composition under different working conditions. This strategy separates the working refrigerant flow in the SMR process into three flows through two phase separators before it flows into the cold box. The first liquid flow is rich in the high-temperature component (isopentane). The second liquid flow is rich in the middle-temperature components (ethylene and propane), and the gas flow is rich in the low-temperature components (nitrogen and methane). By adjusting the flow rates, it is easy to decouple the control variables and automate the system. Finally, this approach was validated by process simulation and shown to be highly adaptive and exergy efficient in response to changing working conditions. - Highlights: • The performance diagnosis mechanism of SMR LNG process is studied. • A measure to automatically change the operation composition as per the working conditions is proposed for SMR process. • SMR process simulation is performed to verify the validity of the control solution. • The control solution notably improves the energy efficiency of SMR process at changing working condition

  15. Co-production of lipids, eicosapentaenoic acid, fucoxanthin, and chrysolaminarin by Phaeodactylum tricornutum cultured in a flat-plate photobioreactor under varying nitrogen conditions

    Science.gov (United States)

    Gao, Baoyan; Chen, Ailing; Zhang, Wenyuan; Li, Aifen; Zhang, Chengwu

    2017-10-01

    The marine diatom Phaeodactylum tricornutum is a polymorphological, ecologically significant, and well-studied model of unicellular microalga. This diatom can accumulate diverse important metabolites. Herein, we cultured P. tricornutum in an internally installed tie-piece flat-plate photobioreactor under 14.5 m mol L-1 (high nitrogen, HN) and 2.9 m mol L-1 (low nitrogen, LN) of KNO3 and assessed its time-resolved changes in biochemical compositions. The results showed that HN was inductive to accumulate high biomass (4.1 g L-1). However, the LN condition could accelerate lipid accumulation in P. tricornutum. The maximum total lipid (TL) content under LN was up to 42.5% of biomass on day 12. Finally, neutral lipids (NLs) were 63.8% and 75.7% of TLs under HN and LN, respectively. The content of EPA ranged from 2.3% to 1.5% of dry weight during the growth period under the two culture conditions. Peak volumetric lipid productivity of 128.4 mg L-1d-1 was achieved in the HN group (on day 9). The highest volumetric productivity values of EPA, chrysolaminarin, and fucoxanthin were obtained in the exponential phase (on day 6) under HN, which were 9.6, 93.6, and 4.7 mg L-1d-1, respectively. In conclusion, extractable amounts of lipids, EPA, fucoxanthin, and chrysolaminarin could be obtained from P. tricornutum by regulating the culture conditions.

  16. [Changes of vascular reactivity and reactive oxygen species in conditions of varying duration of permanent stay in the alienation zone in mice].

    Science.gov (United States)

    Tkachenko, M M; Kotsiuruba, A V; Baziliuk, O V; Horot', I V; Sahach, V F

    2010-01-01

    Peculiarities of changes in the vascular reactivity and in the content of reactive forms of oxygen and stable metabolites of nitric oxide (NO) were studied in the aorta preparations of C57BL/6 and BALB/c mice of the two age groups (6 and 18 mo.), which were born and permanently kept in the Chernobyl alienation zone. The results obtained showed a disturbance of acetylcholine-induced endothelium-dependent reactions of relaxation of smooth muscles of the thoracic aorta. A lower level of NO synthesis and lower level of oxidative arginase metabolism of arginine corresponded to a higher degree of damage of endothelium-dependent reactions of relaxation of the thoracic aorta smooth muscles. A decrease of NO synthesis in conditions of permanent effects of low doses of radiation was conditioned by an increase of generation of reactive forms of oxygen, namely, superoxide and hydroxyl radicals, which might be formed in mitochondria. In conditions of permanent effects of low doses of radiation a lesser level of protein nitrosothilation, same as lesser one of generation of OH-radical, corresponded to a higher level of damage of endothelium-dependent reactions.

  17. Initial reaction between CaO and SO2 under carbonating and non-carbonating conditions

    DEFF Research Database (Denmark)

    Rasmussen, Martin Hagsted; Wedel, Stig; Pedersen, Kim H.

    2015-01-01

    The initial kinetics of the CaO/SO2 reaction have been investigated for reaction times shorter than 1s and in the temperature interval between 450 and 600°C under both carbonating and non-carbonating conditions (0-20 vol% CO2) to clarify how recirculating CaO influences the emission of SO2 from...... showed that the CaO conversion with respect to SO2 declined when the CO2 concentration was increased. Under all conditions, larger specific surface areas of CaO gave higher reaction rates with SO2. Higher temperatures had a positive effect on the reaction between SO2 and CaO under non......-carbonating conditions, but no or even a negative effect under carbonating conditions. The results led to the conclusion that SO2 released from raw meal in the upper stages of the preheater does not to any significant extent react with CaO recirculating in the preheater tower....

  18. Initial conditions for inflation and the energy scale of SUSY-breaking from the (nearly) gaussian sky

    CERN Document Server

    Álvarez-Gaumé, Luis; Jimenez, Raul

    We show how general initial conditions for small field inflation can be obtained in multi-field models. This is provided by non-linear angular friction terms in the inflaton that provide a phase of non-slow-roll inflation before the slow-roll inflation phase. This in turn provides a natural mechanism to star small-field slow-roll at nearly zero velocity for arbitrary initial conditions. We also show that there is a relation between the scale of SUSY breaking sqrt (f) and the amount of non-gaussian fluctuations generated by the inflaton. In particular, we show that in the local non-gaussian shape there exists the relation sqrt (f) = 10^{13} GeV sqrt (f_NL). With current observational limits from Planck, and adopting the minimum amount of non-gaussian fluctuations allowed by single-field inflation, this provides a very tight constraint for the SUSY breaking energy scale sqrt (f) = 3-7 x 10^{13} GeV at 95% confidence. Further limits, or detection, from next year's Planck polarisation data will further tighten th...

  19. A new luminescence dating chronology for the Rhafas cave site (NE Morocco): Insights into Palaeolithic human cultural change under varying palaeoenvironmental conditions in the Maghreb

    Science.gov (United States)

    Dörschner, Nina; Fitzsimmons, Kathryn E.; Ditchfield, Peter; McLaren, Sue J.; Steele, Teresa E.; Zielhofer, Christoph; McPherron, Shannon P.; Bouzouggar, Abdeljalil; Hublin, Jean-Jacques

    2016-04-01

    Archaeological sites in northern Africa provide a rich record that is of increasing importance for current debates relating to the origins of modern human behaviour and to Out of Africa human dispersal events. Particular interest is placed on the cultural transition between the North African Middle Stone Age (MSA) and Late Stone Age (LSA), and the need for accurately defined chronologies, however the timing and nature of Palaeolithic human behaviour and dispersal across north-western Africa (the Maghreb) and potential correlation with environmental conditions remain poorly understood. The inland cave site of Rhafas (Morocco) preserves a long stratified sequence providing valuable chronological information about cultural changes in the Maghreb spanning the North African MSA through to the Neolithic. In this study, we apply optically stimulated luminescence (OSL) dating on sand-sized quartz grains to the cave deposits of Rhafas as well as to a section on the terrace in front of the cave entrance. Single grain OSL dating reliably constrains the timing of technocomplexes beyond the limits of radiocarbon by directly dating sediment associated with archaeological traces. We combine OSL dating with multi-proxy geological investigations (XRF, grain size analyses, stable isotopes, thin sections) to investigate site formation processes and reconstruct palaeoenvironmental conditions during human occupation phases at Rhafas. Our results indicate that the occupation of the site started at least in MIS 6 during a phase of relatively arid environmental conditions. Climatic amelioration after c.140 ka is associated with a change in sediment geochemistry at the site, most likely linked to a change in sediment source due to shifting wind directions. Tanged pieces - typical for the classical Aterian technocomplex - start to occur in the archaeological sequence in MIS 5, consistent with previously published chronological data from the Maghreb. From 55 ka, climatic conditions were

  20. A Comparative Study of Environmental Conditions, Bee Management and the Epidemiological Situation in Apiaries Varying in the Level of Colony Losses

    Directory of Open Access Journals (Sweden)

    Pohorecka Krystyna

    2014-12-01

    Full Text Available Explaining the reasons for the increased mortality of the honey bee (Apis mellifera L. in recent years, in Europe and North America, has become a global research priority in apicultural science. Our project was aimed at determining the relationship between environmental conditions, beekeeping techniques, the epidemiological situation of pathogens, and the mortality rate of bee colonies. Dead bee samples were collected by beekeepers from 2421 colonies. The samples were examined for the presence of V. destructor, Nosema spp. (Nosema apis and Nosema ceranae, chronic bee paralysis virus (CBPV, acute bee paralysis virus (ABPV, deformed wing virus (DWV, and Israeli acute paralysis virus (IAPV.

  1. Projected atoll shoreline and run-up changes in response to sea-level rise and varying large wave conditions at Wake and Midway Atolls, Northwestern Hawaiian Islands

    Science.gov (United States)

    Shope, James B.; Storlazzi, Curt D.; Hoeke, Ron K.

    2017-10-01

    Atoll islands are dynamic features that respond to seasonal alterations in wave conditions and sea level. It is unclear how shoreline wave run-up and erosion patterns along these low elevation islands will respond to projected sea-level rise (SLR) and changes in wave climate over the next century, hindering communities' preparation for the future. To elucidate how these processes may respond to climate change, extreme boreal winter and summer wave conditions under future sea-level rise (SLR) and wave climate scenarios were simulated at two atolls, Wake and Midway, using a shallow-water hydrodynamic model. Nearshore wave conditions were used to compute the potential longshore sediment flux along island shorelines via the CERC empirical formula and wave-driven erosion was calculated as the divergence of the longshore drift; run-up and the locations where the run-up exceed the berm elevation were also determined. SLR is projected to predominantly drive future island morphological change and flooding. Seaward shorelines (i.e., ocean fronted shorelines directly facing incident wave energy) were projected to experience greater erosion and flooding with SLR and in hypothetical scenarios where changes to deep water wave directions were altered, as informed by previous climate change forced Pacific wave modeling efforts. These changes caused nearshore waves to become more shore-normal, increasing wave attack along previously protected shorelines. With SLR, leeward shorelines (i.e., an ocean facing shoreline but sheltered from incident wave energy) became more accretive on windward islands and marginally more erosive along leeward islands. These shorelines became more accretionary and subject to more flooding with nearshore waves becoming more shore-normal. Lagoon shorelines demonstrated the greatest SLR-driven increase in erosion and run-up. They exhibited the greatest relative change with increasing wave heights where both erosion and run-up magnitudes increased. Wider

  2. Projected atoll shoreline and run-up changes in response to sea-level rise and varying large wave conditions at Wake and Midway Atolls, Northwestern Hawaiian Islands

    Science.gov (United States)

    Shope, James B.; Storlazzi, Curt; Hoeke, Ron

    2017-01-01

    Atoll islands are dynamic features that respond to seasonal alterations in wave conditions and sea level. It is unclear how shoreline wave run-up and erosion patterns along these low elevation islands will respond to projected sea-level rise (SLR) and changes in wave climate over the next century, hindering communities' preparation for the future. To elucidate how these processes may respond to climate change, extreme boreal winter and summer wave conditions under future sea-level rise (SLR) and wave climate scenarios were simulated at two atolls, Wake and Midway, using a shallow-water hydrodynamic model. Nearshore wave conditions were used to compute the potential longshore sediment flux along island shorelines via the CERC empirical formula and wave-driven erosion was calculated as the divergence of the longshore drift; run-up and the locations where the run-up exceed the berm elevation were also determined. SLR is projected to predominantly drive future island morphological change and flooding. Seaward shorelines (i.e., ocean fronted shorelines directly facing incident wave energy) were projected to experience greater erosion and flooding with SLR and in hypothetical scenarios where changes to deep water wave directions were altered, as informed by previous climate change forced Pacific wave modeling efforts. These changes caused nearshore waves to become more shore-normal, increasing wave attack along previously protected shorelines. With SLR, leeward shorelines (i.e., an ocean facing shoreline but sheltered from incident wave energy) became more accretive on windward islands and marginally more erosive along leeward islands. These shorelines became more accretionary and subject to more flooding with nearshore waves becoming more shore-normal. Lagoon shorelines demonstrated the greatest SLR-driven increase in erosion and run-up. They exhibited the greatest relative change with increasing wave heights where both erosion and run-up magnitudes increased. Wider

  3. Estimating pesticide sampling rates by the polar organic chemical integrative sampler (POCIS) in the presence of natural organic matter and varying hydrodynamic conditions

    International Nuclear Information System (INIS)

    Charlestra, Lucner; Amirbahman, Aria; Courtemanch, David L.; Alvarez, David A.; Patterson, Howard

    2012-01-01

    The polar organic chemical integrative sampler (POCIS) was calibrated to monitor pesticides in water under controlled laboratory conditions. The effect of natural organic matter (NOM) on the sampling rates (R s ) was evaluated in microcosms containing −1 of total organic carbon (TOC). The effect of hydrodynamics was studied by comparing R s values measured in stirred (SBE) and quiescent (QBE) batch experiments and a flow-through system (FTS). The level of NOM in the water used in these experiments had no effect on the magnitude of the pesticide sampling rates (p > 0.05). However, flow velocity and turbulence significantly increased the sampling rates of the pesticides in the FTS and SBE compared to the QBE (p < 0.001). The calibration data generated can be used to derive pesticide concentrations in water from POCIS deployed in stagnant and turbulent environmental systems without correction for NOM. - Highlights: ► We assessed the effect of TOC and stirring on pesticide sampling rates by POCIS. ► Total organic carbon (TOC) had no effect on the sampling rates. ► Water flow and stirring significantly increased the magnitude of the sampling rates. ► The sampling rates generated are directly applicable to field conditions. - This study provides POCIS sampling rates data that can be used to estimate freely dissolved concentrations of toxic pesticides in natural waters.

  4. Transients from initial conditions based on Lagrangian perturbation theory in N-body simulations II: the effect of the transverse mode

    International Nuclear Information System (INIS)

    Tatekawa, Takayuki

    2014-01-01

    We study the initial conditions for cosmological N-body simulations for precision cosmology. In general, Zel'dovich approximation has been applied for the initial conditions of N-body simulations for a long time. These initial conditions provide incorrect higher-order growth. These error caused by setting up the initial conditions by perturbation theory is called transients. We investigated the impact of transient on non-Gaussianity of density field by performing cosmological N-body simulations with initial conditions based on first-, second-, and third-order Lagrangian perturbation theory in previous paper. In this paper, we evaluates the effect of the transverse mode in the third-order Lagrangian perturbation theory for several statistical quantities such as power spectrum and non-Gaussianty. Then we clarified that the effect of the transverse mode in the third-order Lagrangian perturbation theory is quite small

  5. Estimating pesticide sampling rates by the polar organic chemical integrative sampler (POCIS) in the presence of natural organic matter and varying hydrodynamic conditions

    Science.gov (United States)

    Charlestra, Lucner; Amirbahman, Aria; Courtemanch, David L.; Alvarez, David A.; Patterson, Howard

    2012-01-01

    The polar organic chemical integrative sampler (POCIS) was calibrated to monitor pesticides in water under controlled laboratory conditions. The effect of natural organic matter (NOM) on the sampling rates (Rs) was evaluated in microcosms containing -1 of total organic carbon (TOC). The effect of hydrodynamics was studied by comparing Rs values measured in stirred (SBE) and quiescent (QBE) batch experiments and a flow-through system (FTS). The level of NOM in the water used in these experiments had no effect on the magnitude of the pesticide sampling rates (p > 0.05). However, flow velocity and turbulence significantly increased the sampling rates of the pesticides in the FTS and SBE compared to the QBE (p < 0.001). The calibration data generated can be used to derive pesticide concentrations in water from POCIS deployed in stagnant and turbulent environmental systems without correction for NOM.

  6. A Mathematical Model of Hourly Solar Radiation in Varying Weather Conditions for a Dynamic Simulation of the Solar Organic Rankine Cycle

    Directory of Open Access Journals (Sweden)

    Taehong Sung

    2015-07-01

    Full Text Available A mathematical model of hourly solar radiation with weather variability is proposed based on the simple sky model. The model uses a superposition of trigonometric functions with short and long periods. We investigate the effects of the model variables on the clearness (kD and the probability of persistence (POPD indices and also evaluate the proposed model for all of the kD-POPD weather classes. A simple solar organic Rankine cycle (SORC system with thermal storage is simulated using the actual weather conditions, and then, the results are compared with the simulation results using the proposed model and the simple sky model. The simulation results show that the proposed model provides more accurate system operation characteristics than the simple sky model.

  7. Heterogeneous nucleation helps the search for initial crystallization conditions of γ-glutamyl transpeptidase from Bacillus licheniformis

    International Nuclear Information System (INIS)

    Lin, Long-Liu; Merlino, Antonello

    2013-01-01

    An additional example in which heterogeneous nucleation has helped in the search for crystallization conditions of a protein is reported. Optimization of the crystallization conditions led to the formation of single crystals of γ-glutamyl transpeptidase from B. licheniformis that diffracted to about 3.0 Å resolution. Here, the crystallization and preliminary X-ray diffraction studies of Bacillus licheniformis γ-glutamyl transpeptidase (BlGT) are reported. The serendipitous finding of heterogeneous nucleants in the initial experiments provided the first crystallization conditions for the protein. Crystals were grown by hanging-drop vapour diffusion using a precipitant solution consisting of 20%(w/v) PEG 3350, 0.2 M magnesium chloride hexahydrate, 0.1 M Tris–HCl pH 8.2. The protein crystallized in the orthorhombic space group P2 1 2 1 2 1 , with one heterodimer per asymmetric unit and unit-cell parameters a = 60.90, b = 61.97, c = 148.24 Å. The BlGT crystals diffracted to 2.95 Å resolution

  8. On the appropriate definition of soil profile configuration and initial conditions for land surface-hydrology models in cold regions

    Science.gov (United States)

    Sapriza-Azuri, Gonzalo; Gamazo, Pablo; Razavi, Saman; Wheater, Howard S.

    2018-06-01

    Arctic and subarctic regions are amongst the most susceptible regions on Earth to global warming and climate change. Understanding and predicting the impact of climate change in these regions require a proper process representation of the interactions between climate, carbon cycle, and hydrology in Earth system models. This study focuses on land surface models (LSMs) that represent the lower boundary condition of general circulation models (GCMs) and regional climate models (RCMs), which simulate climate change evolution at the global and regional scales, respectively. LSMs typically utilize a standard soil configuration with a depth of no more than 4 m, whereas for cold, permafrost regions, field experiments show that attention to deep soil profiles is needed to understand and close the water and energy balances, which are tightly coupled through the phase change. To address this gap, we design and run a series of model experiments with a one-dimensional LSM, called CLASS (Canadian Land Surface Scheme), as embedded in the MESH (Modélisation Environmentale Communautaire - Surface and Hydrology) modelling system, to (1) characterize the effect of soil profile depth under different climate conditions and in the presence of parameter uncertainty; (2) assess the effect of including or excluding the geothermal flux in the LSM at the bottom of the soil column; and (3) develop a methodology for temperature profile initialization in permafrost regions, where the system has an extended memory, by the use of paleo-records and bootstrapping. Our study area is in Norman Wells, Northwest Territories of Canada, where measurements of soil temperature profiles and historical reconstructed climate data are available. Our results demonstrate a dominant role for parameter uncertainty, that is often neglected in LSMs. Considering such high sensitivity to parameter values and dependency on the climate condition, we show that a minimum depth of 20 m is essential to adequately represent

  9. On the appropriate definition of soil profile configuration and initial conditions for land surface–hydrology models in cold regions

    Directory of Open Access Journals (Sweden)

    G. Sapriza-Azuri

    2018-06-01

    Full Text Available Arctic and subarctic regions are amongst the most susceptible regions on Earth to global warming and climate change. Understanding and predicting the impact of climate change in these regions require a proper process representation of the interactions between climate, carbon cycle, and hydrology in Earth system models. This study focuses on land surface models (LSMs that represent the lower boundary condition of general circulation models (GCMs and regional climate models (RCMs, which simulate climate change evolution at the global and regional scales, respectively. LSMs typically utilize a standard soil configuration with a depth of no more than 4 m, whereas for cold, permafrost regions, field experiments show that attention to deep soil profiles is needed to understand and close the water and energy balances, which are tightly coupled through the phase change. To address this gap, we design and run a series of model experiments with a one-dimensional LSM, called CLASS (Canadian Land Surface Scheme, as embedded in the MESH (Modélisation Environmentale Communautaire – Surface and Hydrology modelling system, to (1 characterize the effect of soil profile depth under different climate conditions and in the presence of parameter uncertainty; (2 assess the effect of including or excluding the geothermal flux in the LSM at the bottom of the soil column; and (3 develop a methodology for temperature profile initialization in permafrost regions, where the system has an extended memory, by the use of paleo-records and bootstrapping. Our study area is in Norman Wells, Northwest Territories of Canada, where measurements of soil temperature profiles and historical reconstructed climate data are available. Our results demonstrate a dominant role for parameter uncertainty, that is often neglected in LSMs. Considering such high sensitivity to parameter values and dependency on the climate condition, we show that a minimum depth of 20 m is essential to

  10. Dynamics of floret initiation/death determining spike fertility in wheat as affected by Ppd genes under field conditions.

    Science.gov (United States)

    Prieto, Paula; Ochagavía, Helga; Savin, Roxana; Griffiths, Simon; Slafer, Gustavo A

    2018-04-27

    As wheat yield is linearly related to grain number, understanding the physiological determinants of the number of fertile florets based on floret development dynamics due to the role of the particular genes is relevant. The effects of photoperiod genes on dynamics of floret development are largely ignored. Field experiments were carried out to (i) characterize the dynamics of floret primordia initiation and degeneration and (ii) to determine which are the most critical traits of such dynamics in establishing genotypic differences in the number of fertile florets at anthesis in near isogenic lines (NILs) carrying photoperiod-insensitive alleles. Results varied in magnitude between the two growing seasons, but in general introgression of Ppd-1a alleles reduced the number of fertile florets. The actual effect was affected not only by the genome and the doses but also by the source of the alleles. Differences in the number of fertile florets were mainly explained by differences in the floret generation/degeneration dynamics, and in most cases associated with floret survival. Manipulating photoperiod insensitivity, unquestionably useful for changing flowering time, may reduce spike fertility but much less than proportionally to the change in duration of development, as the insensitivity alleles did increase the rate of floret development.

  11. Path integral for stochastic inflation: Nonperturbative volume weighting, complex histories, initial conditions, and the end of inflation

    Science.gov (United States)

    Gratton, Steven

    2011-09-01

    In this paper we present a path integral formulation of stochastic inflation. Volume weighting can be naturally implemented from this new perspective in a very straightforward way when compared to conventional Langevin approaches. With an in-depth study of inflation in a quartic potential, we investigate how the inflaton evolves and how inflation typically ends both with and without volume weighting. The calculation can be carried to times beyond those accessible to conventional Fokker-Planck approaches. Perhaps unexpectedly, complex histories sometimes emerge with volume weighting. The reward for this excursion into the complex plane is an insight into how volume-weighted inflation both loses memory of initial conditions and ends via slow roll. The slow-roll end of inflation mitigates certain “Youngness Paradox”-type criticisms of the volume-weighted paradigm. Thus it is perhaps time to rehabilitate proper-time volume weighting as a viable measure for answering at least some interesting cosmological questions.

  12. Path integral for stochastic inflation: Nonperturbative volume weighting, complex histories, initial conditions, and the end of inflation

    International Nuclear Information System (INIS)

    Gratton, Steven

    2011-01-01

    In this paper we present a path integral formulation of stochastic inflation. Volume weighting can be naturally implemented from this new perspective in a very straightforward way when compared to conventional Langevin approaches. With an in-depth study of inflation in a quartic potential, we investigate how the inflaton evolves and how inflation typically ends both with and without volume weighting. The calculation can be carried to times beyond those accessible to conventional Fokker-Planck approaches. Perhaps unexpectedly, complex histories sometimes emerge with volume weighting. The reward for this excursion into the complex plane is an insight into how volume-weighted inflation both loses memory of initial conditions and ends via slow roll. The slow-roll end of inflation mitigates certain ''Youngness Paradox''-type criticisms of the volume-weighted paradigm. Thus it is perhaps time to rehabilitate proper-time volume weighting as a viable measure for answering at least some interesting cosmological questions.

  13. H I versus H α - comparing the kinematic tracers in modelling the initial conditions of the Mice

    Science.gov (United States)

    Mortazavi, S. Alireza; Lotz, Jennifer M.; Barnes, Joshua E.; Privon, George C.; Snyder, Gregory F.

    2018-03-01

    We explore the effect of using different kinematic tracers (H I and H α) on reconstructing the encounter parameters of the Mice major galaxy merger (NGC 4676A/B). We observed the Mice using the SparsePak Integral Field Unit (IFU) on the WIYN telescope, and compared the H α velocity map with VLA H I observations. The relatively high spectral resolution of our data (R ≈ 5000) allows us to resolve more than one kinematic component in the emission lines of some fibres. We separate the H α-[N II] emission of the star-forming regions from shocks using their [N II]/H α line ratio and velocity dispersion. We show that the velocity of star-forming regions agree with that of the cold gas (H I), particularly, in the tidal tails of the system. We reconstruct the morphology and kinematics of these tidal tails utilizing an automated modelling method based on the IDENTIKIT software package. We quantify the goodness of fit and the uncertainties of the derived encounter parameters. Most of the initial conditions reconstructed using H α and H I are consistent with each other, and qualitatively agree with the results of previous works. For example, we find 210± ^{50}_{40} Myr, and 180± ^{50}_{40} Myr for the time since pericentre, when modelling H α and H I kinematics, respectively. This confirms that in some cases, H α kinematics can be used instead of H I kinematics for reconstructing the initial conditions of galaxy mergers, and our automated modelling method is applicable to some merging systems.

  14. Multidimensional Quantum Mechanical Modeling of Electron Transfer and Electronic Coherence in Plant Cryptochromes: The Role of Initial Bath Conditions.

    Science.gov (United States)

    Mendive-Tapia, David; Mangaud, Etienne; Firmino, Thiago; de la Lande, Aurélien; Desouter-Lecomte, Michèle; Meyer, Hans-Dieter; Gatti, Fabien

    2018-01-11

    A multidimensional quantum mechanical protocol is used to describe the photoinduced electron transfer and electronic coherence in plant cryptochromes without any semiempirical, e.g., experimentally obtained, parameters. Starting from a two-level spin-boson Hamiltonian we look at the effect that the initial photoinduced nuclear bath distribution has on an intermediate step of this biological electron transfer cascade for two idealized cases. The first assumes a slow equilibration of the nuclear bath with respect to the previous electron transfer step that leads to an ultrafast decay with little temperature dependence; while the second assumes a prior fast bath equilibration on the donor potential energy surface leading to a much slower decay, which contrarily displays a high temperature dependence and a better agreement with previous theoretical and experimental results. Beyond Marcus and semiclassical pictures these results unravel the strong impact that the presence or not of equilibrium initial conditions has on the electronic population and coherence dynamics at the quantum dynamics level in this and conceivably in other biological electron transfer cascades.

  15. First results on T91 claddings with and without modified FeCrAlY coatings exposed in PbBi under varying conditions

    International Nuclear Information System (INIS)

    Weisenburger, A.; Heinzel, A.; Miller, G.; Rousanov, A.

    2008-01-01

    It is well known that at temperatures above 500 deg C low activation austenitic steels suffer from severe corrosion in lead or lead-bismuth. Low activation martensitic steels instead form under similar conditions concerning temperature and oxygen content thick oxide scales that periodically may span off. Both groups of materials are therefore restricted to areas having lower temperature load. For parts that are intended to be used in high-temperature regions, like claddings, surface protection has to be applied. From gas turbines the role of elements forming thin stable oxide scales is well understood. The concept chosen here for thermally high loaded parts, the claddings, is the deposition of a FeCrAlY coating of about 30 vt,m thickness that is afterwards re-melted applying a pulsed electron beam (GESA). The beam energy is adjusted in a way to melt the entire coating together with a few thin region of the bulk to create a perfect intermixing at the boundary. This results in a new surface area of the cladding with an aluminium content of the order of 5 wt.% that will be sufficiently high to grow thin stable oxide scales. This concept is proven for austenitic cladding materials like 1.4970 as well as for martensitic ones like T91. In long-term corrosion tests the compatibility to Pb or PbBi, the resistance against corrosion and severe oxidation, was clearly demonstrated. No negative response of such a modified coating on the mechanical properties and the stability under irradiation has been observed as of yet. This paper will focus on the surface modification process, the corrosion results thus far obtained and on the evaluation of some mechanical properties. For example, the swelling of the fuel by irradiation will lead during operation to an increase of the internal pressure. This is simulated in experiments where an internal pressure of defined value was applied on T91 cladding tubes. The influence of flow velocity between to 3 m/s on the oxidation behaviour of T

  16. Initiation of soil formation in weathered sulfidic Cu-Pb-Zn tailings under subtropical and semi-arid climatic conditions.

    Science.gov (United States)

    You, Fang; Dalal, Ram; Huang, Longbin

    2018-08-01

    Field evidence has been scarce about soil (or technosol) formation and direct phytostabilization of base metal mine tailings under field conditions. The present study evaluated key attributes of soil formation in weathered and neutral Cu-Pb-Zn tailings subject to organic amendment (WC: woodchips) and colonization of pioneer native plant species (mixed native woody and grass plant species) in a 2.5-year field trial under subtropical and semi-arid climatic conditions. Key soil indicators of engineered soil formation process were characterized, including organic carbon fractions, aggregation, microbial community and key enzymatic activities. The majority (64-87%) of the OC was stabilized in microaggregate or organo-mineral complexes in the amended tailings. The levels of OC and water soluble OC were elevated by 2-3 folds across the treatments, with the highest level in the treatment of WC and plant colonization (WC+P). Specifically, the WC+P treatment increased the proportion of water stable macroaggregates. Plants further contributed to the N rich organic matter in the tailings, favouring organo-mineral interactions and organic stabilization. Besides, the plants played a major role in boosting microbial biomass and activities in the treated tailings. WC and plants enhanced the contents of organic carbon (OC) associated with aggregates (e.g., physically protected OC), formation of water-stable aggregates (e.g., micro and macroaggregates), chemical buffering capacity (e.g., cation exchange capacity). Microbial community and enzymatic activities were also stimulated in the amended tailings. The present results showed that the formation of functional technosol was initiated in the eco-engineered and weathered Cu-Pb-Zn tailings under field conditions for direct phytostabilization. Copyright © 2018 Elsevier Ltd. All rights reserved.

  17. SIMULATION OF CARS ACCUMULATION PROCESSES FOR SOLVING TASKS OF OPERATIONAL PLANNING IN CONDITIONS OF INITIAL INFORMATION UNCERTAINTY

    Directory of Open Access Journals (Sweden)

    О. A. Tereshchenko

    2017-06-01

    Full Text Available Purpose. The article highlights development of the methodological basis for simulation the processes of cars accumulation in solving operational planning problems under conditions of initial information uncertainty for assessing the sustainability of the adopted planning scenario and calculating the associated technological risks. Methodology. The solution of the problem under investigation is based on the use of general scientific approaches, the apparatus of probability theory and the theory of fuzzy sets. To achieve this purpose, the factors influencing the entropy of operational plans are systematized. It is established that when planning the operational work of railway stations, sections and nodes, the most significant factors that cause uncertainty in the initial information are: a external conditions with respect to the railway ground in question, expressed by the uncertainty of the timing of cars arrivals; b external, hard-to-identify goals for the functioning of other participants in the logistics chain (primarily customers, expressed by the uncertainty of the completion time with the freight cars. These factors are suggested to be taken into account in automated planning through statistical analysis – the establishment and study of the remaining time (prediction errors. As a result, analytical dependencies are proposed for rational representation of the probability density functions of the time residual distribution in the form of point, piecewise-defined and continuous analytic models. The developed models of cars accumulation, the application of which depends on the identified states of the predicted incoming car flow to the accumulation system, are presented below. In addition, the last proposed model is a general case of models of accumulation processes with an arbitrary level of reliability of the initial information for any structure of the incoming flow of cars. In conclusion, a technique for estimating the results of

  18. Constraints on the initial conditions of stellar formation from ISOCAM observations of dense cores seen in absorption

    International Nuclear Information System (INIS)

    Bacmann, Aurore

    1999-01-01

    Stars form in molecular clouds by gravitational collapse of small condensations called pre-stellar cores. This stage of the star formation process is still relatively unknown since these dense cores are deeply embedded within a thick cocoon of matter. The collapse, as well as the accretion phase depend on the structure of these objects. In order to constrain the initial conditions of star formation. We have carried out a study of the density structure of a vast sample of pre-stellar cores that we observed with the mid-infrared camera ISOCAM aboard the ISO satellite. As the cores are very dense and cold, they are seen in absorption against the diffuse mid-infrared background. This absorption method is highly interesting for our study since it is sensitive to the density structure in the outer parts of the cores. The study of these cores enabled us to confirm the presence of a flattening in their central parts, to show that their column density profiles were composed of a portion close to a NH_2 ∝ r"-"1 power-law, and that some of them presented an edge, i.e. that the slope in the outer parts of the profiles became steeper than NH_2 ∝ r"-"2. An implication of the presence of an edge is that the mass reservoir available for star formation in these cores is finite, supporting the idea that the stellar initial mass function is partly determined at a pre-stellar stage. Comparison of our results with various models of core structure shows that the column density profiles we obtained are consistent with ambipolar diffusion models of magnetically supported cores, although they require a strong background magnetic field which has up to now not been observed in these kinds of regions. (author) [fr

  19. Joint route planning under varying market conditions

    NARCIS (Netherlands)

    Cruijssen, Frans; Bräysy, Olli; Dullaert, Wout; Fleuren, Hein; Salomon, Marc

    2007-01-01

    Purpose - To provide empirical evidence on the level of savings that can be attained by joint route planning and how these savings depend on specific market characteristics. Design/methodology/approach - Joint route planning is a measure that companies can take to decrease the costs of their

  20. Experimental study of the initial conditions of the Rayleigh-Taylor instability at the ablation front in inertial confinement fusion

    International Nuclear Information System (INIS)

    Delorme, Barthelemy

    2015-01-01

    Numerous designs and experiments in the domain of Inertial Confinement Fusion (ICF) show that, in both direct and indirect drive approaches, one of the main limitations to reach the ignition is the Rayleigh-Taylor instability (RTI). It may lead to shell disruption and performance degradation of spherically imploding targets. Thus, the understanding and the control of the initial conditions of the RTI is of crucial importance for the ICF program. In this thesis, we present an experimental and theoretical study of the initial conditions of the ablative RTI in direct drive, by means of two experimental campaigns performed on the OMEGA laser facility (LLE, Rochester). The first campaign consisted in studying the laser-imprinted ablative Richtmyer-Meshkov instability (RMI) which starts at the beginning of the interaction and seeds the ablative RTI. We set up an experimental configuration that allowed to measure for the first time the temporal evolution of the laser-imprinted ablative RMI. The experimental results have been interpreted by a theoretical model and numerical simulations performed with the hydrodynamic code CHIC. We show that the best way to control the ablative RMI is to reduce the laser intensity inhomogeneities. This can be achieved with targets covered by a layer of a low density foam. Thus, in the second campaign, we studied for the first time the effect of underdense foams on the growth of the ablative RTI. A layer of low density foam was placed in front of a plastic foil, and the perturbation was imprinted by an intensity modulated laser beam. Experimental data are presented: backscattered laser energy, target dynamic obtained by side-on self emission measurement, and face-on radiographs showing the effect of the foams on the target areal density modulations. These data were interpreted using the CHIC code and the laser-plasma interaction code PARAX. We show that the foams noticeably reduce the amplitude of the laser intensity inhomogeneities and the

  1. How will precipitation change in extratropical cyclones as the planet warms? Insights from a large initial condition climate model ensemble

    Science.gov (United States)

    Yettella, Vineel; Kay, Jennifer E.

    2017-09-01

    The extratropical precipitation response to global warming is investigated within a 30-member initial condition climate model ensemble. As in observations, modeled cyclonic precipitation contributes a large fraction of extratropical precipitation, especially over the ocean and in the winter hemisphere. When compared to present day, the ensemble projects increased cyclone-associated precipitation under twenty-first century business-as-usual greenhouse gas forcing. While the cyclone-associated precipitation response is weaker in the near-future (2016-2035) than in the far-future (2081-2100), both future periods have similar patterns of response. Though cyclone frequency changes are important regionally, most of the increased cyclone-associated precipitation results from increased within-cyclone precipitation. Consistent with this result, cyclone-centric composites show statistically significant precipitation increases in all cyclone sectors. Decomposition into thermodynamic (mean cyclone water vapor path) and dynamic (mean cyclone wind speed) contributions shows that thermodynamics explains 92 and 95% of the near-future and far-future within-cyclone precipitation increases respectively. Surprisingly, the influence of dynamics on future cyclonic precipitation changes is negligible. In addition, the forced response exceeds internal variability in both future time periods. Overall, this work suggests that future cyclonic precipitation changes will result primarily from increased moisture availability in a warmer world, with secondary contributions from changes in cyclone frequency and cyclone dynamics.

  2. (Re)evaluating the Implications of the Autoregressive Latent Trajectory Model Through Likelihood Ratio Tests of Its Initial Conditions.

    Science.gov (United States)

    Ou, Lu; Chow, Sy-Miin; Ji, Linying; Molenaar, Peter C M

    2017-01-01

    The autoregressive latent trajectory (ALT) model synthesizes the autoregressive model and the latent growth curve model. The ALT model is flexible enough to produce a variety of discrepant model-implied change trajectories. While some researchers consider this a virtue, others have cautioned that this may confound interpretations of the model's parameters. In this article, we show that some-but not all-of these interpretational difficulties may be clarified mathematically and tested explicitly via likelihood ratio tests (LRTs) imposed on the initial conditions of the model. We show analytically the nested relations among three variants of the ALT model and the constraints needed to establish equivalences. A Monte Carlo simulation study indicated that LRTs, particularly when used in combination with information criterion measures, can allow researchers to test targeted hypotheses about the functional forms of the change process under study. We further demonstrate when and how such tests may justifiably be used to facilitate our understanding of the underlying process of change using a subsample (N = 3,995) of longitudinal family income data from the National Longitudinal Survey of Youth.

  3. Curli fimbriae are conditionally required in Escherichia coli O157:H7 for initial attachment and biofilm formation.

    Science.gov (United States)

    Carter, Michelle Qiu; Louie, Jacqueline W; Feng, Doris; Zhong, Wayne; Brandl, Maria T

    2016-08-01

    Several species of enteric pathogens produce curli fimbriae, which may affect their interaction with surfaces and other microbes in nonhost environments. Here we used two Escherichia coli O157:H7 outbreak strains with distinct genotypes to understand the role of curli in surface attachment and biofilm formation in several systems relevant to fresh produce production and processing. Curli significantly enhanced the initial attachment of E. coli O157:H7 to spinach leaves and stainless steel surfaces by 5-fold. Curli was also required for E. coli O157:H7 biofilm formation on stainless steel and enhanced biofilm production on glass by 19-27 fold in LB no-salt broth. However, this contribution was not observed when cells were grown in sterile spinach lysates. Furthermore, both strains of E. coli O157:H7 produced minimal biofilms on polypropylene in LB no-salt broth but considerable amounts in spinach lysates. Under the latter conditions, curli appeared to slightly increase biofilm production. Importantly, curli played an essential role in the formation of mixed biofilm by E. coli O157:H7 and plant-associated microorganisms in spinach leaf washes, as revealed by confocal microscopy. Little or no E. coli O157:H7 biofilms were detected at 4 °C, supporting the importance of temperature control in postharvest and produce processing environments. Published by Elsevier Ltd.

  4. Driving force of PCMI failure under reactivity initiated accident conditions and influence of hydrogen embrittlement on failure limit

    International Nuclear Information System (INIS)

    Tomiyasu, Kunihiko; Sugiyama, Tomoyuki; Nakamura, Takehiko; Fuketa, Toyoshi

    2005-09-01

    In order to clarify the driving force of PCMI (Pellet/Cladding Mechanical Interaction) failure on high burnup fuels and to investigate the influence of hydrogen embrittlement on failure limit under RIA (Reactivity Initiated Accident) conditions, RIA-simulation experiments were performed on fresh fuel rods in the NSRR (Nuclear Safety Research Reactor). The driving force of PCMI was restricted only to thermal expansion of pellet by using fresh UO 2 pellets. Fresh claddings were pre-hydrided to simulate hydrogen absorption of high burnup fuel rods. In seven experiments out of fourteen, test rods resulted in PCMI failure, which has been observed in the NSRR tests on high burnup PWR fuels, in terms of the transient behavior and the fracture configuration. This indicates that the driving force of PCMI failure is sufficiently explained with thermal expansion of pellet and a contribution of fission gas on it is small. A large number of incipient cracks were generated in the outer surface of the cladding even on non-failed fuel rods, and they stopped at the boundary between hydride rim, which was a hydride layer localized in the periphery of the cladding, and metallic layer. It suggests that the integrity of the metallic layer except for the hydride rim has particular importance for failure limit. Fuel enthalpy at failure correlates with the thickness of hydride rim, and tends to decrease with thicker hydride layer. (author)

  5. Initiative for local district heating. New chances for municipal utilities. Boundary conditions for the heat market; Initiative Nahwaerme. Neue Chancen fuer Stadtwerke. Rahmenbedingungen fuer den Waermemarkt

    Energy Technology Data Exchange (ETDEWEB)

    Koenig, Michael [K.Group GmbH, Muenchen (Germany). Bereich Nachhaltige Energieversorgung und Stadtentwicklung

    2009-06-15

    In the regulated market, municipal utilities are forced to find new fields of activity. The heat market offers good chances. For example, local district heating grids can be established, independent power generation can be encouraged, and new services can be offered which may increase customer loyalty. The district heating initiative of the Baden-Wuerttemberg Minister of the Environment was launched early in 2009 with the intention to offer valuable assistance to the municipal utilities. (orig.)

  6. An experimental seasonal hydrological forecasting system over the Yellow River basin - Part 1: Understanding the role of initial hydrological conditions

    Science.gov (United States)

    Yuan, Xing; Ma, Feng; Wang, Linying; Zheng, Ziyan; Ma, Zhuguo; Ye, Aizhong; Peng, Shaoming

    2016-06-01

    The hydrological cycle over the Yellow River has been altered by the climate change and human interventions greatly during past decades, with a decadal drying trend mixed with a large variation of seasonal hydrological extremes. To provide support for the adaptation to a changing environment, an experimental seasonal hydrological forecasting system is established over the Yellow River basin. The system draws from a legacy of a global hydrological forecasting system that is able to make use of real-time seasonal climate predictions from North American Multimodel Ensemble (NMME) climate models through a statistical downscaling approach but with a higher resolution and a spatially disaggregated calibration procedure that is based on a newly compiled hydrological observation dataset with 5 decades of naturalized streamflow at 12 mainstream gauges and a newly released meteorological observation dataset including 324 meteorological stations over the Yellow River basin. While the evaluation of the NMME-based seasonal hydrological forecasting will be presented in a companion paper to explore the added values from climate forecast models, this paper investigates the role of initial hydrological conditions (ICs) by carrying out 6-month Ensemble Streamflow Prediction (ESP) and reverse ESP-type simulations for each calendar month during 1982-2010 with the hydrological models in the forecasting system, i.e., a large-scale land surface hydrological model and a global routing model that is regionalized over the Yellow River. In terms of streamflow predictability, the ICs outweigh the meteorological forcings up to 2-5 months during the cold and dry seasons, but the latter prevails over the former in the predictability after the first month during the warm and wet seasons. For the streamflow forecasts initialized at the end of the rainy season, the influence of ICs for lower reaches of the Yellow River can be 5 months longer than that for the upper reaches, while such a difference

  7. Robust Initial Wetness Condition Framework of an Event-Based Rainfall–Runoff Model Using Remotely Sensed Soil Moisture

    Directory of Open Access Journals (Sweden)

    Wooyeon Sunwoo

    2017-01-01

    Full Text Available Runoff prediction in limited-data areas is vital for hydrological applications, such as the design of infrastructure and flood defenses, runoff forecasting, and water management. Rainfall–runoff models may be useful for simulation of runoff generation, particularly event-based models, which offer a practical modeling scheme because of their simplicity. However, there is a need to reduce the uncertainties related to the estimation of the initial wetness condition (IWC prior to a rainfall event. Soil moisture is one of the most important variables in rainfall–runoff modeling, and remotely sensed soil moisture is recognized as an effective way to improve the accuracy of runoff prediction. In this study, the IWC was evaluated based on remotely sensed soil moisture by using the Soil Conservation Service-Curve Number (SCS-CN method, which is one of the representative event-based models used for reducing the uncertainty of runoff prediction. Four proxy variables for the IWC were determined from the measurements of total rainfall depth (API5, ground-based soil moisture (SSMinsitu, remotely sensed surface soil moisture (SSM, and soil water index (SWI provided by the advanced scatterometer (ASCAT. To obtain a robust IWC framework, this study consists of two main parts: the validation of remotely sensed soil moisture, and the evaluation of runoff prediction using four proxy variables with a set of rainfall–runoff events in the East Asian monsoon region. The results showed an acceptable agreement between remotely sensed soil moisture (SSM and SWI and ground based soil moisture data (SSMinsitu. In the proxy variable analysis, the SWI indicated the optimal value among the proposed proxy variables. In the runoff prediction analysis considering various infiltration conditions, the SSM and SWI proxy variables significantly reduced the runoff prediction error as compared with API5 by 60% and 66%, respectively. Moreover, the proposed IWC framework with

  8. The Advantages of Hybrid 4DEnVar in the Context of the Forecast Sensitivity to Initial Conditions

    Science.gov (United States)

    Song, Hyo-Jong; Shin, Seoleun; Ha, Ji-Hyun; Lim, Sujeong

    2017-11-01

    Hybrid four-dimensional ensemble variational data assimilation (hybrid 4DEnVar) is a prospective successor to three-dimensional variational data assimilation (3DVar) in operational weather prediction centers currently developing a new weather prediction model and those that do not operate adjoint models. In experiments using real observations, hybrid 4DEnVar improved Northern Hemisphere (NH; 20°N-90°N) 500 hPa geopotential height forecasts up to 5 days in a NH summer month compared to 3DVar, with statistical significance. This result is verified against ERA-Interim through a Monte Carlo test. By a regression analysis, the sensitivity of 5 day forecast is associated with the quality of the initial condition. The increased analysis skill for midtropospheric midlatitude temperature and subtropical moisture has the most apparent effect on forecast skill in the NH including a typhoon prediction case. Through attributing the analysis improvements by hybrid 4DEnVar separately to the ensemble background error covariance (BEC), its four-dimensional (4-D) extension, and climatological BEC, it is revealed that the ensemble BEC contributes to the subtropical moisture analysis, whereas the 4-D extension does to the midtropospheric midlatitude temperature. This result implies that hourly wind-mass correlation in 6 h analysis window is required to extract the potential of hybrid 4DEnVar for the midlatitude temperature analysis to the maximum. However, the temporal ensemble correlation, in hourly time scale, between moisture and another variable is invalid so that it could not work for improving the hybrid 4DEnVar analysis.

  9. Different target-discrimination times can be followed by the same saccade-initiation timing in different stimulus conditions during visual searches

    Science.gov (United States)

    Tanaka, Tomohiro; Nishida, Satoshi

    2015-01-01

    The neuronal processes that underlie visual searches can be divided into two stages: target discrimination and saccade preparation/generation. This predicts that the length of time of the prediscrimination stage varies according to the search difficulty across different stimulus conditions, whereas the length of the latter postdiscrimination stage is stimulus invariant. However, recent studies have suggested that the length of the postdiscrimination interval changes with different stimulus conditions. To address whether and how the visual stimulus affects determination of the postdiscrimination interval, we recorded single-neuron activity in the lateral intraparietal area (LIP) when monkeys (Macaca fuscata) performed a color-singleton search involving four stimulus conditions that differed regarding luminance (Bright vs. Dim) and target-distractor color similarity (Easy vs. Difficult). We specifically focused on comparing activities between the Bright-Difficult and Dim-Easy conditions, in which the visual stimuli were considerably different, but the mean reaction times were indistinguishable. This allowed us to examine the neuronal activity when the difference in the degree of search speed between different stimulus conditions was minimal. We found that not only prediscrimination but also postdiscrimination intervals varied across stimulus conditions: the postdiscrimination interval was longer in the Dim-Easy condition than in the Bright-Difficult condition. Further analysis revealed that the postdiscrimination interval might vary with stimulus luminance. A computer simulation using an accumulation-to-threshold model suggested that the luminance-related difference in visual response strength at discrimination time could be the cause of different postdiscrimination intervals. PMID:25995344

  10. Influence of Cu(NO32 initiation additive in two-stage mode conditions of coal pyrolytic decomposition

    Directory of Open Access Journals (Sweden)

    Larionov Kirill

    2017-01-01

    Full Text Available Two-stage process (pyrolysis and oxidation of brown coal sample with Cu(NO32 additive pyrolytic decomposition was studied. Additive was introduced by using capillary wetness impregnation method with 5% mass concentration. Sample reactivity was studied by thermogravimetric analysis with staged gaseous medium supply (argon and air at heating rate 10 °C/min and intermediate isothermal soaking. The initiative additive introduction was found to significantly reduce volatile release temperature and accelerate thermal decomposition of sample. Mass-spectral analysis results reveal that significant difference in process characteristics is connected to volatile matter release stage which is initiated by nitrous oxide produced during copper nitrate decomposition.

  11. Comparisons of Stuttering Frequency during and after Speech Initiation in Unaltered Feedback, Altered Auditory Feedback and Choral Speech Conditions

    Science.gov (United States)

    Saltuklaroglu, Tim; Kalinowski, Joseph; Robbins, Mary; Crawcour, Stephen; Bowers, Andrew

    2009-01-01

    Background: Stuttering is prone to strike during speech initiation more so than at any other point in an utterance. The use of auditory feedback (AAF) has been found to produce robust decreases in the stuttering frequency by creating an electronic rendition of choral speech (i.e., speaking in unison). However, AAF requires users to self-initiate…

  12. The influence of discontinuity and orthotropy of fracture toughness on conditions of fracture initiation in singular stress concentrators

    Czech Academy of Sciences Publication Activity Database

    Klusák, Jan; Profant, T.; Knésl, Zdeněk; Kotoul, M.

    2013-01-01

    Roč. 110, SEP (2013), s. 438-447 ISSN 0013-7944 R&D Projects: GA ČR GAP108/10/2049 Institutional support: RVO:68081723 Keywords : Stability criterion of notch es * crack initiation * Singular stress concentrators * bi-material notch Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 1.662, year: 2013

  13. Initial data of seismic input and soil conditions of Kozloduy NPP site. Extension to Part 2 soil conditions, issued October '93

    International Nuclear Information System (INIS)

    Boyadjiev, Z.

    1995-01-01

    On the basis of the results of the carried out experimental (laboratory and in situ) investigations of the dynamic characteristics, the following conclusions for the Kozloduy NPP site are presented. (1) The established through experimental studies relationships for the shear module and the damping factor as strain dependent of representative samples of soils of the site profile, can be used for all similar soils in the profile in the different parts of the site, taking into account the possible differences by means of the initial shear module in the normalized relationship for the respective generalized soil type. (2) When solving the problems of the site response and the 'soil - structure analysis', the geotechnical seismic model of the 'free field' profile can be assumed for all parts of the NPP site. (3) The changes of the lithological profile in different parts of the site, in respect to type and thickness, as well as in view of the different way and depth of the NPP structures foundation, make it necessary the elaboration of a geotechnical seismic model of the profile below the foundation plates of the reactor buildings of the NPP units in each particular case. These models can be made out on the basis of the summarized data about the shear velocities of the soil types, the lithological data of the studied boreholes in these places and the data having natural bulk density from 30 - 40 m depth determined by the laboratory studies of samples of these soils, assuming with approximation that the geotechnical seismic model below this depth is the same as the one of the 'free field'. (4) Studies have been carried out through in situ and laboratory studies of all the fundamental structures on the NPP site and the results of them are sufficient as an addition to the present initial data for solving the problems of the site response and the 'soil-structure inter-action' analyses of each structure

  14. Travelers' use of the WSDOT traffic conditions web site : customer satisfaction evaluation -- Metropolitan Model Deployment Initiative : Seattle, Washington

    Science.gov (United States)

    2000-01-28

    This report presents the results of an evaluation of public use of the Washington State Department of Transportation's (WSDOT) traffic conditions web site. This research was sponsored by the US Department of Transportation to assess customer satisfac...

  15. The flux pinning properties of BaSnO{sub 3}-added GdBa{sub 2}Cu3O{sub 7-δ} films with varying growth conditions

    Energy Technology Data Exchange (ETDEWEB)

    Lee, J. K.; Oh, J. Y.; Kang, B. [Dept. of Physics, Chungbuk National University, Cheongju (Korea, Republic of); Lee, J. M.; Kang, W. N. [Dept. of Physics, Sungkyunkwan University, Suwon (Korea, Republic of)

    2017-09-15

    Addition of BaSnO{sub 3} (BSO) to GdBa{sub 2}Cu{sub 3}O{sub 7-δ} (GdBCO) is reported to enhance the flux pinning property of GdBCO thick films. To investigate the effect of growth condition on the pinning properties, 700 nm-thick BSO-added GdBCO films deposited with varying temperatures and growth rates were prepared by using a pulsed laser deposition method. As the deposition temperature increases, the critical current density and the pinning force density show an improved field dependence up to 750 ℃ due to the increase in the formation of the a-axis growth and the BSO nanostructures. The films deposited at higher temperatures show degraded surfaces and as a result, degraded pinning behaviors. For the change in growth rate, the critical current density and the pinning force increase as the repetition rate increase at low magnetic fields, but this behavior is reversed in high magnetic fields. These results indicate that the film growth conditions significantly affect the formation of BSO nanostructures and the pinning properties of BSO-added GdBCO films.

  16. Influence of the initial surface condition on the release of nickel alloys in the primary circuit of PWRs

    Energy Technology Data Exchange (ETDEWEB)

    Guinard, L.; Kerrec, O.; Noel, D.; Gardey, S.; Coulet, F.

    1997-01-01

    The effect of surface condition on corrosion and release and the mechanisms involved are investigated. The detrimental and beneficial effects of certain conditions or processes are identified: role of the last thermomechanical treatment, detrimental effect of cold-work, beneficial effect of electropolishing. The results can not be explained by mechanisms based only on solubility and mass transfer. Ionic migration through the inner barrier film is also probably involved. (K.A.). 32 refs.

  17. Influence of the initial surface condition on the release of nickel alloys in the primary circuit of PWRs

    International Nuclear Information System (INIS)

    Guinard, L.; Kerrec, O.; Noel, D.; Gardey, S.; Coulet, F.

    1997-01-01

    The effect of surface condition on corrosion and release and the mechanisms involved are investigated. The detrimental and beneficial effects of certain conditions or processes are identified: role of the last thermomechanical treatment, detrimental effect of cold-work, beneficial effect of electropolishing. The results can not be explained by mechanisms based only on solubility and mass transfer. Ionic migration through the inner barrier film is also probably involved. (K.A.)

  18. varying elastic parameters distributions

    KAUST Repository

    Moussawi, Ali

    2014-12-01

    The experimental identication of mechanical properties is crucial in mechanics for understanding material behavior and for the development of numerical models. Classical identi cation procedures employ standard shaped specimens, assume that the mechanical elds in the object are homogeneous, and recover global properties. Thus, multiple tests are required for full characterization of a heterogeneous object, leading to a time consuming and costly process. The development of non-contact, full- eld measurement techniques from which complex kinematic elds can be recorded has opened the door to a new way of thinking. From the identi cation point of view, suitable methods can be used to process these complex kinematic elds in order to recover multiple spatially varying parameters through one test or a few tests. The requirement is the development of identi cation techniques that can process these complex experimental data. This thesis introduces a novel identi cation technique called the constitutive compatibility method. The key idea is to de ne stresses as compatible with the observed kinematic eld through the chosen class of constitutive equation, making possible the uncoupling of the identi cation of stress from the identi cation of the material parameters. This uncoupling leads to parametrized solutions in cases where 5 the solution is non-unique (due to unknown traction boundary conditions) as demonstrated on 2D numerical examples. First the theory is outlined and the method is demonstrated in 2D applications. Second, the method is implemented within a domain decomposition framework in order to reduce the cost for processing very large problems. Finally, it is extended to 3D numerical examples. Promising results are shown for 2D and 3D problems.

  19. The role of grain boundary fission gases in high burn-up fuel under reactivity initiated accident conditions

    International Nuclear Information System (INIS)

    Lemoine, F.; Papin, J.; Frizonnet, J.M.; Cazalis, B.; Rigat, H.

    2002-01-01

    In the frame of reactivity-initiated accidents (RIA) studies, the CABRI REP-Na programme is currently performed, focused on high burn-up UO 2 and MOX fuel behaviour. From 1993 to 1998, seven tests were performed with UO 2 fuel and three with MOX fuel. In all these tests, particular attention has been devoted to the role of fission gases in transient fuel behaviour and in clad loading mechanisms. From the analysis of experimental results, some basic phenomena were identified and a better understanding of the transient fission gas behaviour was obtained in relation to the fuel and clad thermo-mechanical evolution in RIA, but also to the initial state of the fuel before the transient. A high burn-up effect linked to the increasing part of grain boundary gases is clearly evidenced in the final gas release, which would also significantly contribute to the clad loading mechanisms. (authors)

  20. A Utilitarian Perspective of Social and Medical Contributions to Three Illustrative Conditions, and Recent UK NHS Policy Initiatives

    OpenAIRE

    Middleton, Hugh; Shaw, Ian

    2007-01-01

    Background: To date debate concerning the relative merits of social and medical sciences has been\\ud largely academic.\\ud Aims: To outline and critically appraise a utilitarian approach to mental health research that reflects a\\ud critical realist perspective.\\ud Method: Consideration of the relative utility of differing approaches to illustrative ‘‘psychiatric’’\\ud disorders, and recent policy initiatives.\\ud Results: Socially relevant outcomes of Bipolar Affective Disorder are determined by...

  1. Einstein boundary conditions in relation to constraint propagation for the initial-boundary value problem of the Einstein equations

    International Nuclear Information System (INIS)

    Frittelli, Simonetta; Gomez, Roberto

    2004-01-01

    We show how the use of the normal projection of the Einstein tensor as a set of boundary conditions relates to the propagation of the constraints, for two representations of the Einstein equations with vanishing shift vector: the Arnowitt-Deser-Misner formulation, which is ill posed, and the Einstein-Christoffel formulation, which is symmetric hyperbolic. Essentially, the components of the normal projection of the Einstein tensor that act as nontrivial boundary conditions are linear combinations of the evolution equations with the constraints that are not preserved at the boundary, in both cases. In the process, the relationship of the normal projection of the Einstein tensor to the recently introduced 'constraint-preserving' boundary conditions becomes apparent

  2. Effect of initial conditions on two-dimensional Rayleigh-Taylor instability and transition to turbulence in planar blast-wave-driven systems

    International Nuclear Information System (INIS)

    Miles, A.R.; Edwards, M.J.; Greenough, J.A.

    2004-01-01

    Perturbations on an interface driven by a strong blast wave grow in time due to a combination of Rayleigh-Taylor, Richtmyer-Meshkov, and decompression effects. In this paper, the results from a computational study of such a system under drive conditions to be attainable on the National Ignition Facility [E. M. Campbell, Laser Part. Beams 9, 209 (1991)] are presented. Using the multiphysics, adaptive mesh refinement, higher order Godunov Eulerian hydrocode, Raptor [L. H. Howell and J. A. Greenough, J. Comput. Phys. 184, 53 (2003)], the late nonlinear instability evolution for multiple amplitude and phase realizations of a variety of multimode spectral types is considered. Compressibility effects preclude the emergence of a regime of self-similar instability growth independent of the initial conditions by allowing for memory of the initial conditions to be retained in the mix-width at all times. The loss of transverse spectral information is demonstrated, however, along with the existence of a quasi-self-similar regime over short time intervals. Certain aspects of the initial conditions, including the rms amplitude, are shown to have a strong effect on the time to transition to the quasi-self-similar regime

  3. The significance of nitrogen limited condition in the initiation of lipid biosynthesis in Aurantiochytrium sp. SW1

    Science.gov (United States)

    Haladu, Zangoma Maryam; Ibrahim, Izyanti; Hamid, Aidil Abdul

    2018-04-01

    The manner of the onset of lipid synthesis in Aurantiochytrium sp. SW1 as well as the possible role of NAD+ dependent isocitrate dehydrogenase (NAD+: ICDH) in the initiation of lipid biosynthesis were studied. The initiation of lipid synthesis in the microalgae was not associated with the cessation of growth, but commence at the early phase of growth. Substantial amount of lipid (30 %, g/g biomass) was accumulated during the active growth phase at 48 h with growth rate decreasing from 0.11 g/L/h during active growth to 0.02 g/L/h in the limited growth phase. At that period the activity of NAD+: ICDH was still detectable although it slightly decreased to 20 nmol/min/mg in 48 h from 25 nmol/min/mg at 24 h. Analysis of ammonium sulfate fractionated of NAD+: ICDH activity showed that NAD+: ICDH was not completely dependent on adenosine monophosphate (AMP) for its activity, although the presence of AMP increased the enzyme's affinity towards its substrate (isocitrate) indicated by the low Km value of the enzyme for isocitrate. While citrate acts as inhibitor of the enzyme only at high concentration. The probable implications of these properties to the regulation of lipid are discussed.

  4. Zn(II, Mn(II and Sr(II Behavior in a Natural Carbonate Reservoir System. Part I: Impact of Salinity, Initial pH and Initial Zn(II Concentration in Atmospheric Conditions

    Directory of Open Access Journals (Sweden)

    Auffray B.

    2016-07-01

    Full Text Available The sorption of inorganic elements on carbonate minerals is well known in strictly controlled conditions which limit the impact of other phenomena such as dissolution and/or precipitation. In this study, we evidence the behavior of Zn(II (initially in solution and two trace elements, Mn(II and Sr(II (released by carbonate dissolution in the context of a leakage from a CO2 storage site. The initial pH chosen are either equal to the pH of the water-CO2 equilibrium (~ 2.98 or equal to the pH of the water-CO2-calcite system (~ 4.8 in CO2 storage conditions. From this initial influx of liquid, saturated or not with respect to calcite, the batch experiments evolve freely to their equilibrium, as it would occur in a natural context after a perturbation. The batch experiments are carried out on two natural carbonates (from Lavoux and St-Emilion with PCO2 = 10−3.5 bar, with different initial conditions ([Zn(II]i from 10−4 to 10−6 M, either with pure water or 100 g/L NaCl brine. The equilibrium regarding calcite dissolution is confirmed in all experiments, while the zinc sorption evidenced does not always correspond to the two-step mechanism described in the literature. A preferential sorption of about 10% of the concentration is evidenced for Mn(II in aqueous experiments, while Sr(II is more sorbed in saline conditions. This study also shows that this preferential sorption, depending on the salinity, is independent of the natural carbonate considered. Then, the simulations carried out with PHREEQC show that experiments and simulations match well concerning the equilibrium of dissolution and the sole zinc sorption, with log KZn(II ~ 2 in pure water and close to 4 in high salinity conditions. When the simulations were possible, the log K values for Mn(II and Sr(II were much different from those in the literature obtained by sorption in controlled conditions. It is shown that a new conceptual model regarding multiple Trace Elements (TE sorption is

  5. A necessary and sufficient condition for well-posedness of initial value problems of retarded functional differential equations

    Science.gov (United States)

    Nishiguchi, Junya

    2017-09-01

    We introduce the retarded functional differential equations (RFDEs) with general delay structure to treat various delay differential equations (DDEs) in a unified way and to clarify the delay structure in those dynamics. We are interested in the question as to which space of histories is suitable for the dynamics of each DDE, and investigate the well-posedness of the initial value problems (IVPs) of the RFDEs. A main theorem is that the IVP is well-posed for any ;admissible; history functional if and only if the semigroup determined by the trivial RFDE x ˙ = 0 is continuous. We clarify the meaning of the Hale-Kato axiom (Hale & Kato [12]) by applying this result to RFDEs with infinite delay. We also apply the result to DDEs with unbounded time- and state-dependent delays.

  6. Evaluation des performances de la production de graines par tamisage manuel du sol chez trois variétés de Stylosanthes guianensis (Aublet Swartz, dans les conditions du Plateau des Batéké (RDC

    Directory of Open Access Journals (Sweden)

    Bulakali, BP.

    2013-01-01

    Full Text Available Performance Assessment of the Production of Seeds by Manual Sieving of the Soil of Three Varieties of Stylosanthes guianensis (Aublet Swartz under the Conditions of the Batéké Plateau (DRC. In manual agriculture with low resources level, Stylosanthes guianensis is one of the most interesting cover crop for developing direct seeding mulch-based cropping systems. To promote its cultivation in the DRC, the performances of a seed production method by sieving of the soil were evaluated for three varieties of Stylo (a local ecotype, CIAT 184 variety, and 202cc variety in two sites of the Batéké plateau characterized by contrasted fertility levels. The results obtained demonstrate the interest of the seed multiplication method tested, both in quantities and quality of the produced seeds. The production cost of one kg of seeds varies with the soil fertility, the planting date, and the cultivar. Among the three compared varieties, CIAT 184 variety produced the highest quantity of seeds. If sown at the beginning of the long rainy season, after a long fallow, in one of the most fertile soils of the plateau, this cultivar can produce 600 kg ha-1 seed in the first year of cultivation with a production cost of USD 1.31 kg-1, equivalent to less than 0.5 man.day.kg-1.

  7. Increase on the initial soluble heme levels in acidic conditions is an important mechanism for spontaneous heme crystallization in vitro.

    Directory of Open Access Journals (Sweden)

    Renata Stiebler

    Full Text Available BACKGROUND: Hemozoin (Hz is a heme crystal that represents a vital pathway for heme disposal in several blood-feeding organisms. Recent evidence demonstrated that β-hematin (βH (the synthetic counterpart of Hz formation occurs under physiological conditions near synthetic or biological hydrophilic-hydrophobic interfaces. This seems to require a heme dimer acting as a precursor of Hz crystals that would be formed spontaneously in the absence of the competing water molecules bound to the heme iron. Here, we aimed to investigate the role of medium polarity on spontaneous βH formation in vitro. METHODOLOGY/PRINCIPAL FINDINGS: We assessed the effect of water content on spontaneous βH formation by using the aprotic solvent dimethylsulfoxide (DMSO and a series of polyethyleneglycols (PEGs. We observed that both DMSO and PEGs (3.350, 6.000, 8.000, and 22.000 increased the levels of soluble heme under acidic conditions. These compounds were able to stimulate the production of βH crystals in the absence of any biological sample. Interestingly, the effects of DMSO and PEGs on βH formation were positively correlated with their capacity to promote previous heme solubilization in acidic conditions. Curiously, a short chain polyethyleneglycol (PEG 300 caused a significant reduction in both soluble heme levels and βH formation. Finally, both heme solubilization and βH formation strongly correlated with reduced medium water activity provided by increased DMSO concentrations. CONCLUSIONS: The data presented here support the notion that reduction of the water activity is an important mechanism to support spontaneous heme crystallization, which depends on the previous increase of soluble heme levels.

  8. The use of human samples obtained during medicolegal autopsies in research: An introduction to current conditions and initiatives in Japan.

    Science.gov (United States)

    Tsujimura-Ito, Takako; Inoue, Yusuke; Muto, Kaori; Yoshida, Ken-Ichi

    2017-04-01

    Background Leftover samples obtained during autopsies are extremely important basic materials for forensic research. However, there are no established practices for research-related use of obtained samples. Objective This study discusses good practice for the secondary use of samples collected during medicolegal autopsies. Methods A questionnaire was posted to all 76 departments of forensic medicine performing medicolegal autopsies in Japan, and 48 responses were received (response rate: 63.2%). As a secondary analysis, we surveyed information provided on department websites. Results Ethical reviews conducted when samples were to be used for research varied greatly among departments, with 21 (43.8%) departments reporting 'fundamentally, all cases are subject to review', eight (16.7%) reporting 'only some are subject to review' and 17 (39.6%) reporting 'none are subject to review'. Information made available on websites indicated that 11 departments had a statement of some type to bereaved families about the potential research use of human samples obtained during autopsies. Nine of these included a notice stating that bereaved families may revoke their consent for use. Several departments used an opt-out system. Conclusion There is no common practice in the field of legal medicine on the ethical use for medical research of leftover samples from medicolegal autopsies. The trust of not only bereaved families but also society in general is required for the scientific validity and social benefits of medical studies using leftover samples from medicolegal autopsies through the use of opt-out consenting and offline and online dissemination and public-relations activities.

  9. Numerical doubly-periodic solution of the (2+1)-dimensional Boussinesq equation with initial conditions by the variational iteration method

    International Nuclear Information System (INIS)

    Inc, Mustafa

    2007-01-01

    In this Letter, a scheme is developed to study numerical doubly-periodic solutions of the (2+1)-dimensional Boussinesq equation with initial condition by the variational iteration method. As a result, the approximate and exact doubly-periodic solutions are obtained. For different modulus m, comparison between the approximate solution and the exact solution is made graphically, revealing that the variational iteration method is a powerful and effective tool to non-linear problems

  10. Program of in-pile IASCC testing under the simulated actual plant condition. Development of technique for in-pile IASCC initiation test in JMTR

    International Nuclear Information System (INIS)

    Ugachi, Hirokazu; Tsukada, Takashi; Kaji, Yoshiyuki; Nagata, Nobuaki; Dozaki, Koji; Takiguchi, Hideki

    2003-01-01

    Irradiation assisted stress corrosion cracking (IASCC) is caused by the synergistic effects of neutron irradiation, stress and corrosion by high temperature water. It is, therefore, essential to perform in-pile SCC tests, which are material tests under the conditions simulating those of actual LWR operation, in order to clarify the precise mechanism of the phenomenon, though mainly out-of-pile SCC tests for irradiated materials have been carried out in this research field. There are, however, many difficulties to perform in-pile SCC tests. Performing in-pile SCC tests, essential key techniques must be developed. Hence as a part of development of the key techniques for in-pile SCC tests, we have embarked on development of the test technique which enables us to obtain the information concerning the effect of such parameters as applied stress level, water chemistry, irradiation conditions, etc. on the crack initiation behavior. Although it is difficult to detect the crack initiation in in-pile SCC tests, the crack initiation can be evaluated by the detection of specimen rupture if the cross section area of the specimen is small enough. Therefore, we adopted the uniaxial constant loading (UCL) test with small tensile specimens. This paper will describe the current status of the development of several techniques for in-pile SCC initiation tests in JMTR and the results of the performance tests of the designed testing unit using the out-of-pile loop facility. (author)

  11. On the initial conditions and solutions of the semi-classical Einstein equations in a cosmological scenario

    Energy Technology Data Exchange (ETDEWEB)

    Pinamonti, Nicola [Hamburg Univ. (Germany). 2. Inst. fuer Theoretische Physik

    2010-01-15

    In this paper we discuss the backreaction of a massive quantum scalar field on the curvature, the latter treated as a classical field. Furthermore, we deal with this problem in the realm of cosmological spacetime by analyzing the Einstein equations in a semiclassical fashion. More precisely, we show that, at least on small intervals of time, solutions for this interacting system exist. This result is achieved furnishing an iteration scheme and showing that it converges in the appropriate Banach space. Moreover, we show that the quantum states with good ultraviolet behavior (Hadamard property) used in order to obtain the backreaction will be completely individuated by their form on the initial surface if chosen to be lightlike. On large intervals of time the situation is more complicated but, if the spacetime is expanding, we show that the end limiting point of the evolution does not depend strongly on the quantum state, because, in this limit, the expectation values of the matter fields responsible for the backreaction do not depend on the particular homogeneous Hadamard state at all. Finally, we comment on the interpretation of the semiclassical Einstein equations for this kind of problems. Although the fluctuations of the expectation values of pointlike fields diverge, if the spacetime and the quantum state have a large spatial symmetry and if we consider the smeared fields on regions of large spatial volume, they tend to vanish. Assuming this point of view the semiclassical Einstein equations become more reliable. (orig.)

  12. On the initial conditions and solutions of the semi-classical Einstein equations in a cosmological scenario

    International Nuclear Information System (INIS)

    Pinamonti, Nicola

    2010-01-01

    In this paper we discuss the backreaction of a massive quantum scalar field on the curvature, the latter treated as a classical field. Furthermore, we deal with this problem in the realm of cosmological spacetime by analyzing the Einstein equations in a semiclassical fashion. More precisely, we show that, at least on small intervals of time, solutions for this interacting system exist. This result is achieved furnishing an iteration scheme and showing that it converges in the appropriate Banach space. Moreover, we show that the quantum states with good ultraviolet behavior (Hadamard property) used in order to obtain the backreaction will be completely individuated by their form on the initial surface if chosen to be lightlike. On large intervals of time the situation is more complicated but, if the spacetime is expanding, we show that the end limiting point of the evolution does not depend strongly on the quantum state, because, in this limit, the expectation values of the matter fields responsible for the backreaction do not depend on the particular homogeneous Hadamard state at all. Finally, we comment on the interpretation of the semiclassical Einstein equations for this kind of problems. Although the fluctuations of the expectation values of pointlike fields diverge, if the spacetime and the quantum state have a large spatial symmetry and if we consider the smeared fields on regions of large spatial volume, they tend to vanish. Assuming this point of view the semiclassical Einstein equations become more reliable. (orig.)

  13. Development of the BWR Dry Core Initial and Boundary Conditions for the SNL XR2 Experiments; TOPICAL

    International Nuclear Information System (INIS)

    Ott, L.J.

    1994-01-01

    The objectives of the Boiling Water Reactor Experimental Analysis and Model Development for Severe Accidents (BEAMD) Program at the Oak Ridge National Laboratory (ORNL) are: (1) the development of a sound quantitative understanding of boiling water reactor (BWR) core melt progression; this includes control blade and channel box effects, metallic melt relocation and possible blockage formation under severe accident conditions, and (2) provision of BWR melt progression modeling capabilities in SCDAP/RELAP5 (consistent with the BWR experimental data base). This requires the assessment of current modeling of BWR core melt progression against the expanding BWR data base. Emphasis is placed upon data from the BWR tests in the German CORA test facility and from the ex-reactor experiments[Sandia National Laboratories (SNL)] on metallic melt relocation and blockage formation in BWRs, as well as upon in-reactor data from the Annular Core Research Reactor (ACRR) DF-4 BWR test (conducted in 1986 at SNL). The BEAMD Program is a derivative of the BWR Severe Accident Technology Programs at ORNL. The ORNL BWR programs have studied postulated severe accidents in BWRs and have developed a set of models specific to boiling water reactor response under severe accident conditions. These models, in an experiment-specific format, have been successfully applied to both pretest and posttest analyses of the DF-4 experiment, and the BWR severe fuel damage (SFD) experiments performed in the CORA facility at the Kernforschungszentrum Karlsruhe (KfK) in Germany, resulting in excellent agreement between model prediction and experiment. The ORNL BWR models have provided for more precise predictions of the conditions in the BWR experiments than were previously available. This has provided a basis for more accurate interpretation of the phenomena for which the experiments are performed. The experiment-specific models, as used in the ORNL DF-4 and CORA BWR experimental analyses, also provide a basis

  14. Mechanical energy release and fuel fragmentation in high energy deposition into fuel under a reactivity initiated accident condition

    International Nuclear Information System (INIS)

    Tsuruta, Takaharu; Saito, Shinzo; Ochiai, Masaaki

    1985-01-01

    The fuel fragmentation is one of important subjects to be studied, since it is one of basic processes of molten fuel-coolant interaction (MFCI) and it has not yet been made clear enough. Accordingly, UO 2 fuel fragmentation was studied in the NSRR experiments simulating a reactivity initiated accident (RIA). As results of the experiments, the distribution of the size of fuel fragments was obtained and the mechanism of fuel fragmentation was discussed as described below. It was revealed that the distribution was well displayed in the form of logarithmic Rosin-Rammler's distribution law. It was shown that the conversion ratio from thermal energy to mechanical in the experiment was in inverse propotion to the volume-surface mean diameter defined as a ratio of the total volume of fragments to the total surface. Consequently, it was confirmed that the mean diameter was proper as an index for the degree of the fuel fragmentation. It was also pointed out that the Weber-type hydraulic instability model for fragmentation was consistent with the experimental results. The mechanism of the fuel fragmentation is understood as follows. Cladding tube is ruptured due to the increase in rod pressure when fuel is molten, and then molten fuel spouts through the openings in the form of jet. As a result of molten fuel spouting, fuel is fragmented by the Weber-type of hydraulic instability. The model well explains the effects of experimental parameters as heat deposition, subcooling of cooling water and capsule diameter, on the fuel fragmentation. According to the model, fuel fragments have to be spherical. There were many spherical particles which had hollow and burst crack. This may be due to internal burst during solidification process. The items which should be studied further are also described in the end of this report. (author)

  15. Preparing for the future today: The findings of the NEA RK and M initiative for the short term (This period covers several decades and likely more than 100 years. The actual duration will vary across national programmes)

    International Nuclear Information System (INIS)

    Schroeder, Jantine

    2015-01-01

    The NEA initiative on Records, Knowledge and Memory (RK and M) across Generations is an initiative that expresses, supports and aims to answer to an evolution in long-term radioactive waste management (RWM) thinking over the past decades. In the earlier days, the vision seems to have been that waste management ends with the closure of disposal sites. Oversight after closure was not an issue that was studied, (tacitly) assuming safe oblivion of geological repositories, or that archives, markers and other similar tools would suffice, e.g. to avoid human intrusion and/or to understand the nature of the underground facility. Today, it is recognised that oversight should take place for as long as practicable. The new vision includes the preservation of information to be used by future generations. In this paper we want to highlight that such a vision shift with regard to the future requires an accompanying shift with regard to present thinking and practices. To this aim, we will outline some of the studies undertaken within the RK and M initiative that substantiate this finding that the future starts today, and offer suggestions to support its concretization. societal oversight as long as practicable, we should acknowledge the fact that RK and M loss takes place rapidly if it is not acted upon in a conscious and ongoing manner that involves various actors and does more than dumping records into archives. The success of RK and M preservation cannot be judged today by whether they will last for one or ten thousand years. Instead, it lies in establishing and maintaining awareness of the need and responsibility for RK and M preservation in the minds of regulators, operators, stakeholders and, especially in the longer term, the local and regional authorities and general public. Therefore, we should not only think about future activities, but act upon the idea that the long term starts today, and that RK and M preservation needs to be prepared for in the present, while the

  16. ngVLA Key Science Goal 2: Probing the Initial Conditions for Planetary Systems and Life with Astrochemistry

    Science.gov (United States)

    McGuire, Brett; ngVLA Science Working Group 1

    2018-01-01

    One of the most challenging aspects in understanding the origin and evolution of planets and planetary systems is tracing the influence of chemistry on the physical evolution of a system from a molecular cloud to a solar system. Existing facilities have already shown the stunning degree of molecular complexity present in these systems. The unique combination of sensitivity and spatial resolution offered by the ngVLA will permit the observation of both highly complex and very low-abundance chemical species that are exquisitely sensitive to the physical conditions and evolutionary history of their sources, which are out of reach of current observatories. In turn, by understanding the chemical evolution of these complex molecules, unprecedentedly detailed astrophysical insight can be gleaned from these astrochemical observations.This poster will overview a number of key science goals in astrochemistry which will be enabled by the ngVLA, including:1) imaging of the deepest, densest regions in protoplanetary disks and unveiling the physical history through isotopic ratios2) probing the ammonia snow line in these disks, thought to be the only viable tracer of the water snowline3) observations of the molecular content of giant planet atmospheres4) detections of new, complex molecules, potentially including the simplest amino acids and sugars5) tracing the origin of chiral excess in star-forming regions

  17. Changes in bacterial community structure correlate with initial operating conditions of a field-scale denitrifying fluidized bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, C. [Miami Univ., Oxford, OH (United States). Dept. of Microbiology; Wu, W.M. [Stanford Univ., CA (United States). Dept. of Civil and Environmental Engineering; Gentry, T.J. [Oak Ridge National Lab., TN (US). Environmental Sciences Div.] (and others)

    2006-08-15

    High levels of nitrate are present in groundwater migrating from the former waste disposal ponds at the Y-12 National Security Complex in Oak Ridge, TN. A field-scale denitrifying fluidized bed reactor (FBR) was designed, constructed, and operated with ethanol as an electron donor for the removal of nitrate. After inoculation, biofilms developed on the granular activated carbon particles. Changes in the bacterial community of the FBR were evaluated with clone libraries (n=500 partial sequences) of the small-subunit rRNA gene for samples taken over a 4-month start-up period. Early phases of start-up operation were characterized by a period of selection, followed by low diversity and predominance by Azoarcus-like sequences. Possible explanations were high pH and nutrient limitations. After amelioration of these conditions, diversification increased rapidly, with the appearance of Dechloromonas, Pseudomonas, and Hydrogenophaga sequences. Changes in NO{sub 3}, SO{sub 4}, and pH also likely contributed to shifts in community composition. The detection of sulfate-reducing-bacteria-like sequences closely related to Desulfovibrio and Desulfuromonas in the FBR have important implications for downstream applications at the field site. (orig.)

  18. Initial discussion on ore-forming conditions and prospecting direction of volcanic type uranium deposits in the gangdise tectonic belt

    International Nuclear Information System (INIS)

    Zhao Baoguang; Wang Sili; Wang Qin; Sun Yue; Du Xiaolin; Chen Yuliang

    2010-01-01

    The most active volcanic activity in the Gangdise tectonic belt happened in early Cretaceous, Paleocene and Eocene, and Eocene is the most active period. The distribution of volcanic rock is controlled by latitudinal deep fault and deuteric longitudinal fault. Paleo-volcano was located at these structural compounds frequently. The volcanics which appeared near the merdional large scale pull-apart construction in Neogene is considered as land facies medium-acidic volcanics which brought by various kinds of volcanic basin. A large stream sediment anomaly (>6.8 x 10 -6 ) has been found at Cenozoic volcanics in south of CuoQin basin, and its areas amount to hundreds square kilometers. The uranium content of volcanics in Wuyu basin amounts to 20.0 x 10 -6 at most. It has favorable Ore-forming conditions for forming volcanic type uranium deposit due to the volcanic geologic environment, accompanying mineral, region feature of geochemistry and geophysical, volcanic-tectonic depression and so on. The major prospecting targets are the south of CuoQin basin and the Nanmulin district. (authors)

  19. Self-similar bumps and wiggles: Isolating the evolution of the BAO peak with power-law initial conditions

    International Nuclear Information System (INIS)

    Orban, Chris; Weinberg, David H.

    2011-01-01

    Motivated by cosmological surveys that demand accurate theoretical modeling of the baryon acoustic oscillation (BAO) feature in galaxy clustering, we analyze N-body simulations in which a BAO-like Gaussian bump modulates the linear theory correlation function ξ L (r)=(r 0 /r) n+3 of an underlying self-similar model with initial power spectrum P(k)=Ak n . These simulations test physical and analytic descriptions of BAO evolution far beyond the range of most studies, since we consider a range of underlying power spectra (n=-0.5, -1, -1.5) and evolve simulations to large effective correlation amplitudes (equivalent to σ 8 =4-12 for r bao =100h -1 Mpc). In all cases, nonlinear evolution flattens and broadens the BAO bump in ξ(r) while approximately preserving its area. This evolution resembles a diffusion process in which the bump width σ bao is the quadrature sum of the linear theory width and a length proportional to the rms relative displacement Σ pair (r bao ) of particle pairs separated by r bao . For n=-0.5 and n=-1, we find no detectable shift of the location of the BAO peak, but the peak in the n=-1.5 model shifts steadily to smaller scales, following r peak /r bao =1-1.08(r 0 /r bao ) 1.5 . The perturbation theory scheme of McDonald (2007) [P. McDonald, Phys. Rev. D 75, 043514 (2007).] and, to a lesser extent, standard 1-loop perturbation theory are fairly successful at explaining the nonlinear evolution of the Fourier power spectrum of our models. Analytic models also explain why the ξ(r) peak shifts much more for n=-1.5 than for n≥-1, though no ab initio model we have examined reproduces all of our numerical results. Simulations with L box =10r bao and L box =20r bao yield consistent results for ξ(r) at the BAO scale, provided one corrects for the integral constraint imposed by the uniform density box.

  20. Chemical and physical reservoir parameters at initial conditions in Berlin geothermal field, El Salvador: a first assessment

    Energy Technology Data Exchange (ETDEWEB)

    D`Amore, F. [CNR, Pisa (Italy). International Institute for Geothermal Research ; Mejia, J.T. [Comision Ejuctiva Hidroelectrica del Rio Lempa, El Salvador (El Salvador)

    1999-02-01

    A study has been made to obtain the main chemical and physical reservoir conditions of the Berlin field (El Salvador), before the commencement of large-scale exploitation of the geothermal resource. The upflow zone and the main flow path within the geothermal system have been determined from the area distribution of chemical parameters such as Cl concentrations, ratios such as Na/K, K/Mg, K/Ca, and temperatures computed from silica concentrations and cation ratios. Gas compositions have been used to calculate reservoir parameters such as temperature, steam fraction and P{sub CO{sub 2}}. The computer code WATCH (new edition 1994) has been used to evaluate the temperature of equilibrium between the aqueous species and selected alteration minerals in the reservoir. The fluid in Berlin flows to the exploited reservoir from the south, entering it in the vicinity of well TR-5. Along its flow-path (south-north direction), the fluid is cooled by boiling and conductive cooling. The chloride-enthalpy diagram indicates the existence of a parent water, with a chemical composition similar to well TR-5, that boils and the residual brine produces the fluid of well TR-3, which is very concentrated in salts. The fluid of TR-5 is probably produced from this parent water, generating the fluids of wells TR-2 and TR-9 by boiling, and the fluids of wells TR-1 and TR-4 by conductive cooling. The computed values for the deep steam fraction clearly indicate that this is a liquid-dominated system, with computed temperature values decreasing from 310{sup o}C (upflow zone) to about 230{sup o}C, from south to north. (author)

  1. Time-varying BRDFs.

    Science.gov (United States)

    Sun, Bo; Sunkavalli, Kalyan; Ramamoorthi, Ravi; Belhumeur, Peter N; Nayar, Shree K

    2007-01-01

    The properties of virtually all real-world materials change with time, causing their bidirectional reflectance distribution functions (BRDFs) to be time varying. However, none of the existing BRDF models and databases take time variation into consideration; they represent the appearance of a material at a single time instance. In this paper, we address the acquisition, analysis, modeling, and rendering of a wide range of time-varying BRDFs (TVBRDFs). We have developed an acquisition system that is capable of sampling a material's BRDF at multiple time instances, with each time sample acquired within 36 sec. We have used this acquisition system to measure the BRDFs of a wide range of time-varying phenomena, which include the drying of various types of paints (watercolor, spray, and oil), the drying of wet rough surfaces (cement, plaster, and fabrics), the accumulation of dusts (household and joint compound) on surfaces, and the melting of materials (chocolate). Analytic BRDF functions are fit to these measurements and the model parameters' variations with time are analyzed. Each category exhibits interesting and sometimes nonintuitive parameter trends. These parameter trends are then used to develop analytic TVBRDF models. The analytic TVBRDF models enable us to apply effects such as paint drying and dust accumulation to arbitrary surfaces and novel materials.

  2. Predictors for the initiation of a basal supported oral therapy (BOT) in type 2 diabetic patients under real-life conditions in Germany.

    Science.gov (United States)

    Kostev, Karel; Dippel, Franz-Werner

    2012-12-01

    To assess the predictors for the initiation of a basal supported oral therapy (BOT) in type 2 diabetic patients under real-life conditions in Germany. A historical cohort study based on representative German real life data (IMS(®) Disease Analyzer) was performed. The study included patients with type 2 diabetes who started an oral antidiabetic drug (OAD) treatment between 01/1995 and 12/2011. Patients with consecutive treatment data for at least 12 months before the initiation of an OAD treatment were eligible for the analysis. The time-dependent rate of patients starting an insulin therapy with a long-acting insulin was calculated by use of the Kaplan-Meier method. Multivariate Cox regression analyses were applied to identify associated factors. The study included 194,967 patients with type 2 diabetes mellitus being on OAD therapy. 24,964 patients were switched to BOT during the observational period. The probability of switching to insulin therapy was associated with three main predictors such as (1) poor metabolic control, (2) midlife age and (3) number and type of the OAD before insulinization. The variation of the HbA1c threshold to HbA1c≥7.5 leads to comparable outcomes with significant HR. The highest probability of initiating a basal supported oral therapy (BOT) under real life conditions was found for patients with poor metabolic control, midlife age and pre-treatment with specific OADs such as SU, GLI or AGI before initiation of insulin therapy. Copyright © 2012 Primary Care Diabetes Europe. Published by Elsevier Ltd. All rights reserved.

  3. Detection of dynamically varying interaural time differences

    DEFF Research Database (Denmark)

    Kohlrausch, Armin; Le Goff, Nicolas; Breebaart, Jeroen

    2010-01-01

    of fringes surrounding the probe is equal to the addition of the effects of the individual fringes. In this contribution, we present behavioral data for the same experimental condition, called dynamically varying ITD detection, but for a wider range of probe and fringe durations. Probe durations varied...

  4. Semiclassical modelling of finite-pulse effects on non-adiabatic photodynamics via initial condition filtering: The predissociation of NaI as a test case

    Energy Technology Data Exchange (ETDEWEB)

    Martínez-Mesa, Aliezer [Departmento de Física Teórica, Universidad de la Habana, San Lázaro y L, La Habana 10400 (Cuba); Institut für Chemie, Universität Potsdam, Karl-Liebknecht-Strasse 24-25, D-14476 Potsdam-Golm (Germany); Saalfrank, Peter [Institut für Chemie, Universität Potsdam, Karl-Liebknecht-Strasse 24-25, D-14476 Potsdam-Golm (Germany)

    2015-05-21

    Femtosecond-laser pulse driven non-adiabatic spectroscopy and dynamics in molecular and condensed phase systems continue to be a challenge for theoretical modelling. One of the main obstacles is the “curse of dimensionality” encountered in non-adiabatic, exact wavepacket propagation. A possible route towards treating complex molecular systems is via semiclassical surface-hopping schemes, in particular if they account not only for non-adiabatic post-excitation dynamics but also for the initial optical excitation. One such approach, based on initial condition filtering, will be put forward in what follows. As a simple test case which can be compared with exact wavepacket dynamics, we investigate the influence of the different parameters determining the shape of a laser pulse (e.g., its finite width and a possible chirp) on the predissociation dynamics of a NaI molecule, upon photoexcitation of the A(0{sup +}) state. The finite-pulse effects are mapped into the initial conditions for semiclassical surface-hopping simulations. The simulated surface-hopping diabatic populations are in qualitative agreement with the quantum mechanical results, especially concerning the subpicosend photoinduced dynamics, the main deviations being the relative delay of the non-adiabatic transitions in the semiclassical picture. Likewise, these differences in the time-dependent electronic populations calculated via the semiclassical and the quantum methods are found to have a mild influence on the overall probability density distribution. As a result, the branching ratios between the bound and the dissociative reaction channels and the time-evolution of the molecular wavepacket predicted by the semiclassical method agree with those computed using quantum wavepacket propagation. Implications for more challenging molecular systems are given.

  5. Under Pressure: Financial Effect of the Hospital-Acquired Conditions Initiative-A Statewide Analysis of Pressure Ulcer Development and Payment.

    Science.gov (United States)

    Meddings, Jennifer; Reichert, Heidi; Rogers, Mary A M; Hofer, Timothy P; McMahon, Laurence F; Grazier, Kyle L

    2015-07-01

    To assess the financial effect of the 2008 Hospital-Acquired Conditions Initiative (HACI) pressure ulcer payment changes on Medicare, other payers, and hospitals. Retrospective before-and-after study of all-payer statewide administrative data for more than 2.4 million annual adult discharges in 2007 and 2009 using the Healthcare Cost and Utilization Project State Inpatient Datasets for California. How often and by how much the 2008 payment changes for pressure ulcers affected hospital payment was assessed. Nonfederal acute care California hospitals (N = 311). Adults discharged from acute-care hospitals. Pressure ulcer rates and hospital payment changes. Hospital-acquired pressure ulcer rates were low in 2007 (0.28%) and 2009 (0.27%); present-on-admission pressure ulcer rates increased from 2.3% in 2007 to 3.0% in 2009. According to clinical stage of pressure ulcer (available in 2009), hospital-acquired Stage III and IV ulcers occurred in 603 discharges (0.02%); 60,244 discharges (2.42%) contained other pressure ulcer diagnoses. Payment removal for Stage III and IV hospital-acquired ulcers reduced payment in 75 (0.003%) discharges, for a statewide payment decrease of $310,444 (0.001%) for all payers and $199,238 (0.001%) for Medicare. For all other pressure ulcers, the Hospital-Acquired Conditions Initiative reduced hospital payment in 20,246 (0.81%) cases (including 18,953 cases with present-on-admission ulcers), reducing statewide payment by $62,538,586 (0.21%) for all payers and $47,237,984 (0.32%) for Medicare. The total financial effect of the 2008 payment changes for pressure ulcers was negligible. Most payment decreases occurred by removal of comorbidity payments for present-on-admission pressure ulcers other than Stages III and IV. The removal of payment for hospital-acquired Stage III and IV ulcers by implementation of the HACI policy was 1/200th that of the removal of payment for other types of pressure ulcers that occurred in implementation of the

  6. Improvement of a mesoscale atmospheric dynamic model PHYSIC. Utilization of output from synoptic numerical prediction model for initial and boundary condition

    International Nuclear Information System (INIS)

    Nagai, Haruyasu; Yamazawa, Hiromi

    1995-03-01

    This report describes the improvement of the mesoscale atmospheric dynamic model which is a part of the atmospheric dispersion calculation model PHYSIC. To introduce large-scale meteorological changes into the mesoscale atmospheric dynamic model, it is necessary to make the initial and boundary conditions of the model by using GPV (Grid Point Value) which is the output of the numerical weather prediction model of JMA (Japan Meteorological Agency). Therefore, the program which preprocesses the GPV data to make a input file to PHYSIC was developed and the input process and the methods of spatial and temporal interpolation were improved to correspond to the file. Moreover, the methods of calculating the cloud amount and ground surface moisture from GPV data were developed and added to the model code. As the example of calculation by the improved model, the wind field simulations of a north-west monsoon in winter and a sea breeze in summer in the Tokai area were also presented. (author)

  7. Fitting Nonlinear Ordinary Differential Equation Models with Random Effects and Unknown Initial Conditions Using the Stochastic Approximation Expectation-Maximization (SAEM) Algorithm.

    Science.gov (United States)

    Chow, Sy-Miin; Lu, Zhaohua; Sherwood, Andrew; Zhu, Hongtu

    2016-03-01

    The past decade has evidenced the increased prevalence of irregularly spaced longitudinal data in social sciences. Clearly lacking, however, are modeling tools that allow researchers to fit dynamic models to irregularly spaced data, particularly data that show nonlinearity and heterogeneity in dynamical structures. We consider the issue of fitting multivariate nonlinear differential equation models with random effects and unknown initial conditions to irregularly spaced data. A stochastic approximation expectation-maximization algorithm is proposed and its performance is evaluated using a benchmark nonlinear dynamical systems model, namely, the Van der Pol oscillator equations. The empirical utility of the proposed technique is illustrated using a set of 24-h ambulatory cardiovascular data from 168 men and women. Pertinent methodological challenges and unresolved issues are discussed.

  8. The impact of the uncertainty in the initial soil moisture condition of irrigated areas on the spatiotemporal characteristics of convective activity in Central Greece

    Science.gov (United States)

    Kotsopoulos, Stylianos; Ioannis, Tegoulias; Ioannis, Pytharoulis; Stergios, Kartsios; Dimitrios, Bampzelis; Theodore, Karacostas

    2015-04-01

    The region of Thessaly is the second largest plain in Greece and has a vital role in the financial life of the country, because of its significant agricultural production. The intensive and extensive cultivation of irrigated crops, in combination with the population increase and the alteration of precipitation patterns due to climate change, often leading the region to experience severe drought conditions, especially during the warm period of the year. The aim of the DAPHNE project is to tackle the problem of drought in this area by means of Weather Modification.In the framework of the project DAPHNE, the numerical weather prediction model WRF-ARW 3.5.1 is used to provide operational forecasts and hindcasts for the region of Thessaly. The goal of this study is to investigate the impact of the uncertainty in the initial soil moisture condition of irrigated areas, on the spatiotemporal characteristics of convective activity in the region of interest. To this end, six cases under the six most frequent synoptic conditions, which are associated with convective activity in the region of interest, are utilized, considering six different soil moisture initialization scenarios. In the first scenario (Control Run), the model is initialized with the surface soil moisture of the ECMWF analysis data, that usually does not take into account the modification of soil moisture due to agricultural activity in the area of interest. In the other five scenarios (Experiment 1,2,3,4,5) the soil moisture in the upper soil layers of the study area are modified from -50% to 50% of field capacity (-50%FC, -25%FC, FC, 25%FC, 50%FC),for the irrigated cropland.Three model domains, covering Europe, the Mediterranean Sea and northern Africa (d01), the wider area of Greece (d02) and central Greece - Thessaly region (d03) are used at horizontal grid-spacings of 15km, 5km and 1km respectively. ECMWF operational analyses at 6-hourly intervals (0.25ox0.25o lat.-long.) are imported as initial and

  9. Role of Ocean Initial Conditions to Diminish Dry Bias in the Seasonal Prediction of Indian Summer Monsoon Rainfall: A Case Study Using Climate Forecast System

    Science.gov (United States)

    Koul, Vimal; Parekh, Anant; Srinivas, G.; Kakatkar, Rashmi; Chowdary, Jasti S.; Gnanaseelan, C.

    2018-03-01

    Coupled models tend to underestimate Indian summer monsoon (ISM) rainfall over most of the Indian subcontinent. Present study demonstrates that a part of dry bias is arising from the discrepancies in Oceanic Initial Conditions (OICs). Two hindcast experiments are carried out using Climate Forecast System (CFSv2) for summer monsoons of 2012-2014 in which two different OICs are utilized. With respect to first experiment (CTRL), second experiment (AcSAL) differs by two aspects: usage of high-resolution atmospheric forcing and assimilation of only ARGO observed temperature and salinity profiles for OICs. Assessment of OICs indicates that the quality of OICs is enhanced due to assimilation of actual salinity profiles. Analysis reveals that AcSAL experiment showed 10% reduction in the dry bias over the Indian land region during the ISM compared to CTRL. This improvement is consistently apparent in each month and is highest for June. The better representation of upper ocean thermal structure of tropical oceans at initial stage supports realistic upper ocean stability and mixing. Which in fact reduced the dominant cold bias over the ocean, feedback to air-sea interactions and land sea thermal contrast resulting better representation of monsoon circulation and moisture transport. This reduced bias of tropospheric moisture and temperature over the Indian land mass and also produced better tropospheric temperature gradient over land as well as ocean. These feedback processes reduced the dry bias in the ISM rainfall. Study concludes that initializing the coupled models with realistic OICs can reduce the underestimation of ISM rainfall prediction.

  10. Microbiological changes, shelf life and identification of initial and spoilage microbiota of sea bream fillets stored under various conditions using 16S rRNA gene analysis.

    Science.gov (United States)

    Parlapani, Foteini F; Kormas, Konstantinos Ar; Boziaris, Ioannis S

    2015-09-01

    Sea bream fillets are one of the most important value-added products of the seafood market. Fresh seafood spoils mainly owing to bacterial action. In this study an exploration of initial and spoilage microbiota of sea bream fillets stored under air and commercial modified atmosphere packaging (MAP) at 0 and 5 °C was conducted by 16S rRNA gene sequence analysis of isolates grown on plates. Sensory evaluation and enumeration of total viable counts and spoilage microorganisms were also conducted to determine shelf life and bacterial growth respectively. Different temperatures and atmospheres affected growth and synthesis of spoilage microbiota as well as shelf life. Shelf life under air at 0 and 5 °C was 14 and 5 days respectively, while under MAP it was 20 and 8 days respectively. Initial microbiota were dominated by Pseudomonas fluorescens, Psychrobacter and Macrococcus caseolyticus. Different temperatures and atmospheres affected the synthesis of spoilage microbiota. At the end of shelf life, different phylotypes of Pseudomonas closely related to Pseudomonas fragi were found to dominate in most cases, while Pseudomonas veronii dominated in fillets under MAP at 0 °C. Furthermore, in fillets under MAP at 5 °C, new dominant species such as Carnobacterium maltaromaticum, Carnobacterium divergens and Vagococcus fluvialis were revealed. Different temperature and atmospheric conditions affected bacterial growth, shelf life and the synthesis of spoilage microbiota. Molecular identification revealed species and strains of microorganisms that have not been reported before for sea bream fillets stored under various conditions, thus providing valuable information regarding microbiological spoilage. © 2014 Society of Chemical Industry.

  11. Relación entre la variación de las condiciones ambientales y la temperatura interna de la yema del manzano 'Anna' Inner bud temperature of' Anna' apple trees in relation to varying environmental conditions

    Directory of Open Access Journals (Sweden)

    Casierra Posada Fannor

    2001-12-01

    Full Text Available En Paipa (Colombia, se realizó un ensayo de campo con el fin de determinar el efecto de la variación de las condiciones ambientales sobre la temperatura interna de la yema del manzano 'Anna' cultivado en condiciones de altiplano tropical. Los registros se hicieron en un árbol de cuatro años, el cual se defolió manualmente y se podó pocas semanas después de la cosecha. Se midió la temperatura del aire y se comparó con la temperatura de una yema en el árbol. Para medir la temperatura de la yema se colocó un sensor digital muy delgado entre los catáfilos de la yema; la temperatura ambiente se registró con un termómetro de bulbo. Las mediciones se realizaron cada media hora entre las 7:00 y las 17:30 horas del día, durante 19 días, empezando el día en que el árbol fue defoliado hasta cuando la yema alcanzó el estado fenológico "green tip". Al tiempo con cada medición de temperatura se registró el fenómeno climático más sobresaliente (lluvia, tiempo soleado, viento, tiempo nublado, etc. y los datos se agruparon según cada fenómeno climático. Los resultados mostraron que la yema presentó una temperatura 1,49°C por encima de la temperatura del aire durante el transcurso del día, en la noche no hubo diferencia de temperatura. En condiciones de lluvia, la temperatura
    de la yema estuvo 0,57°C por encima de la temperatura
    del aire. Bajo cielo nublado la yema estuvo 0,56°C más cálida
    que el aire. En condiciones de viento la yema presentó una
    diferencia de 0,87°C sobre la temperatura del aire. En días
    soleados, la yema mantuvo una temperatura 2,3°C sobre la temperatura del aire. Las diferencias entre la temperatura del aire y la de la yema se discuten con base en la transpiración, la convección y la radiación.A field experiment was conducted in Paipa (Colombia to study the effect of environmental varying over inner bud temperature of an 'Anna' apple tree 4 years old growing in tropical

  12. Thermal wave propagation in blood perfused tissues under hyperthermia treatment for unique oscillatory heat flux at skin surface and appropriate initial condition

    Science.gov (United States)

    Dutta, Jaideep; Kundu, Balaram

    2018-05-01

    This paper aims to develop an analytical study of heat propagation in biological tissues for constant and variable heat flux at the skin surface correlated with Hyperthermia treatment. In the present research work we have attempted to impose two unique kind of oscillating boundary condition relevant to practical aspect of the biomedical engineering while the initial condition is constructed as spatially dependent according to a real life situation. We have implemented Laplace's Transform method (LTM) and Green Function (GFs) method to solve single phase lag (SPL) thermal wave model of bioheat equation (TWMBHE). This research work strongly focuses upon the non-invasive therapy by employing oscillating heat flux. The heat flux at the skin surface is considered as constant, sinusoidal, and cosine forms. A comparative study of the impact of different kinds of heat flux on the temperature field in living tissue explored that sinusoidal heat flux will be more effective if the time of therapeutic heating is high. Cosine heating is also applicable in Hyperthermia treatment due to its precision in thermal waveform. The result also emphasizes that accurate observation must be required for the selection of phase angle and frequency of oscillating heat flux. By possible comparison with the published experimental research work and published mathematical study we have experienced a difference in temperature distribution as 5.33% and 4.73%, respectively. A parametric analysis has been devoted to suggest an appropriate procedure of the selection of important design variables in viewpoint of an effective heating in hyperthermia treatment.

  13. How fields vary.

    Science.gov (United States)

    Krause, Monika

    2018-03-01

    Field theorists have long insisted that research needs to pay attention to the particular properties of each field studied. But while much field-theoretical research is comparative, either explicitly or implicitly, scholars have only begun to develop the language for describing the dimensions along which fields can be similar to and different from each other. In this context, this paper articulates an agenda for the analysis of variable properties of fields. It discusses variation in the degree but also in the kind of field autonomy. It discusses different dimensions of variation in field structure: fields can be more or less contested, and more or less hierarchical. The structure of symbolic oppositions in a field may take different forms. Lastly, it analyses the dimensions of variation highlighted by research on fields on the sub- and transnational scale. Post-national analysis allows us to ask how fields relate to fields of the same kind on different scales, and how fields relate to fields on the same scale in other national contexts. It allows us to ask about the role resources from other scales play in structuring symbolic oppositions within fields. A more fine-tuned vocabulary for field variation can help us better describe particular fields and it is a precondition for generating hypotheses about the conditions under which we can expect to observe fields with specified characteristics. © London School of Economics and Political Science 2017.

  14. Influence of the initial metallurgical state and the austenizing conditions on the distribution of austenitc grain size of the martensitic-ferritic steel T91(9%Cr-1%Mo-V-Nb)

    International Nuclear Information System (INIS)

    Zavaleta Gutierrez, N; Luppo, M.I; Danon, C.A; Garcia de Andres, C

    2006-01-01

    It is a known fact that the austenizing conditions (speed of heating to the austenite temperature and austenizing time) as well as the initial metallurgical state of the material strongly influence the distribution of austenitic grain size in steels. This distribution will be one of the parameters that will control the behavior of the material in a later transformation from the austenite -by continuous cooling or in the isothermal case - and this behavior will determine the product's final mechanical properties. Based on the published literature, we have studied the influence of the initial metallurgical state and the speed of heating to austenite on the distribution of austenitic grain size for a certain austenizing temperature and time for a martensitic-iron ASTM A213 grade T91 steel. Two-stage thermal cycles were designed for this, that is, tempering for a variable period of time at the industrial tempering temperature (780 o C) followed by the austenizing (1050 o C, 30 minutes) 'in situ'. We have analyzed the following as a whole: 1) the role of the stabilizing elements (Nb, V) that eventually control the anchoring of the austenitic grain boundary by carbide or carbonitride precipitation. Therefore, we have tried to vary the fraction of these elements present in solid solution by annealing before austenizing. 2) the role of the speed of heating to austenite. In this case, we have considered two different values (1 and 30 o C/s), previously reported as inferior and superior, respectively, to the speed of 'critical' heat needed to produce a distribution of heterogeneous austenitic grain size when the metallurgical state before the austenizing is quenched and tempered. Preliminary results suggest that a annealing stage after tempering in the plant and prior to eventual austenizing significantly reduces the influence of the heating to austenite speed in the development of a heterogeneous structure of austenitic grains (CW)

  15. Towards an improved understanding of hillslope runoff as a supply for groundwater recharge: Assessing hillslope runoff under regional deforestation and varying climate conditions in a drainage basin in central coastal California

    Science.gov (United States)

    Young, K. S.; Beganskas, S.; Fisher, A. T.

    2017-12-01

    We use a hydrologic model to analyze hillslope runoff under a range of climate and land use conditions in the San Lorenzo River Basin (SLRB), central coastal California, including contemporary land use and incremental deforestation. The SLRB is a heavily forested watershed with chronically overdrafted aquifers; in some areas, groundwater levels have been lowered by >50 m in recent decades. Managed aquifer recharge (MAR) can help mitigate declines in groundwater storage, routing excess surface flows to locations where they can infiltrate. We are especially interested in opportunities for collection of stormwater runoff, particularly where development and other changes in landuse have increased hill slope runoff. To assess hillslope runoff at the subwatershed scale (10-100 ha; 25-250 ac), we apply the Precipitation Runoff Modeling System (PRMS) to a high-resolution, digital elevation model and populate the simulation with area- and density-weighted vegetation and soil parameters calculated from high resolution input data. We also develop and apply a catalog of dry, normal, and wet climate scenarios from the historic record (1981-2014). In addition, we simulate conditions ranging from 0 to 100 percent of redwoods harvested (representing the mid-1800s to 1930s logging era) using a historical land use data set to alter soil and vegetation conditions. Results under contemporary land use suggest there are ample opportunities to establish MAR projects during all climate scenarios; hill slope runoff generation is spatially variable and on average exceeds 23,000 ac-ft/yr (3.2 in/yr) during the driest climate scenario. Preliminary results from the deforestation scenarios show notable increases in hillslope runoff with progressive redwood harvesting. Relative to pre-logging conditions, between 1.1 in (dry climates) and 1.5 in (wet climates) more runoff is generated under contemporary conditions, with most of the runoff increase occurring in urban areas. These modeling methods

  16. Productivity of seed agrocenosis of common millet (Panicum miliaceum L. at varying so­ ing w terms and techniques under the conditions of Right- Bank Forest-Steppe

    Directory of Open Access Journals (Sweden)

    С. П. Полторецький

    2013-08-01

    Full Text Available The objective of the research is to improve the techno­logy of growing high-quality seeds of millet broomcorn by means of the optimization of sowing terms and methods, aimed at increasing its productivity and improving seed qualities under conditions of unstable moistening of the Right-Bank Forest-Steppe of Ukraine. Scientific literature review indicates the study of the influence of these technology elements on the formation of sowing qualities and crop capacity of millet seeds has been of schematic and occasional nature. The issue has not been studied in this region condition at all, that is why the research has considerable significance and novelty. Analysis, observations and calculations were done by means of conventional methods. Research results indicate that under conditions of unstable moistening of the southern part of the Right-Bank Forest-Steppe of Ukraine the highest yield of Slobozhanske and Lana varieties was reached at sowing in drills – 39.2 and 41.0 metric centners per hectare, respectively. That was 2.4 and 3.9 metric centners per hectare increase against the wide-row sowing. In the years with optimal hydrothermal conditions maximum seed productivity of millet broomcorn at the level of 4.24 to 4.79 metric tons per hectare (Slobozhanske variety and 4.53 to 5.28 metric tons per hectare (Lana variety was observed at postponing the sowing terms to the third decade of May. If atypical for the region hydrothermal conditions (drought or excessive moistening are forecasted du­ ring the vegetation period of millet, the highest productivity is provided by sowing in the second decade of May. Early sowing in the first decade of May causes decrease in yield at the level of 0.14 to 0.48 metric tons per hectare (Slobozhanske variety and 0.14 to 0.48 metric tons per hectare (Lana variety; if the sowing is postponed to the first decade of June, the yield increases by 0.31 to 0.77 and 0.39 to 0.84 metric tons per hectare, respectively. Early

  17. The influence on the contact condition and initial fixation stability of the main design parameters of a self-expansion type anterior cruciate ligament fixation device

    International Nuclear Information System (INIS)

    Kim, Jong Dae; Oh, Chae Youn; Kim, Cheol Sang

    2008-01-01

    This paper proposes a self-expansion type anterior cruciate ligament fixation device. The proposed fixation device provides graft fixation force by maintaining contact with the bone tunnel. Since the device maintains contact with the bone tunnel by the force that expands by the self-driven elastic force of the device, the main design parameters that determine the performance of this device are the ring thickness and expansion angle. This paper develops the three-dimensional finite element models of the fixation device and bone. By simulation with the developed finite element model, this paper studies the influence of the main design parameters of the device on the maximum stress around the ring when grasping the fixation device. Through the analysis of the stress on the bone tunnel wall when the fixation device comes in contact with the bone tunnel, this paper shows the influence of the main design parameters of the fixation device on the contact condition. In addition, through the analysis of the migration that occur upon application of the pull-out force, this paper studies the influence of the main design parameters on the initial fixation stability of the fixation device

  18. The influence on the contact condition and initial fixation stability of the main design parameters of a self-expansion type anterior cruciate ligament fixation device

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Dae [Jeonju University, Jeonju (Korea, Republic of); Oh, Chae Youn; Kim, Cheol Sang [Chonbuk National University, Jeonju (Korea, Republic of)

    2008-12-15

    This paper proposes a self-expansion type anterior cruciate ligament fixation device. The proposed fixation device provides graft fixation force by maintaining contact with the bone tunnel. Since the device maintains contact with the bone tunnel by the force that expands by the self-driven elastic force of the device, the main design parameters that determine the performance of this device are the ring thickness and expansion angle. This paper develops the three-dimensional finite element models of the fixation device and bone. By simulation with the developed finite element model, this paper studies the influence of the main design parameters of the device on the maximum stress around the ring when grasping the fixation device. Through the analysis of the stress on the bone tunnel wall when the fixation device comes in contact with the bone tunnel, this paper shows the influence of the main design parameters of the fixation device on the contact condition. In addition, through the analysis of the migration that occur upon application of the pull-out force, this paper studies the influence of the main design parameters on the initial fixation stability of the fixation device

  19. Use of fog water to the initial establishment of tree species under conditions of barren Lomas in the Quebrada Topará, Chincha-Perú

    Science.gov (United States)

    Vargas, A.; Cabrera, R.; Bederski, K.; Orellana, A.

    2010-07-01

    The Quebrada Topara is located in the Peruvian coastal desert (13012'L.S, 76009'L.W.) and is influenced by the fog during the winter months, these conditions of high humidity allows its use to achieve the establishment of a permanent vegetation cover Huaquina hill, which is representative at the place of study. Uncounted fog water can be captured and used for irrigation of plants. Also due to the absence of any tree species coverage in this region is not known which or which could have a better performance under these environmental conditions, We used to native species Caesalpinia spinosa "tara" and Schinus molle "molle" also introduced species Casuarina equisetifolia "Casuarina", as these could have a better adaptation. Soil analysis determined a high salinity and nitrogen poverty, preventing water infiltration into the soil and is not used by the plant so that the saline soil difficult to establish plants. This research can be considered an exploratory phase, the objectives were: to determine the potential for fog water harvesting to capture in the study area, to assess for 20 months the initial performance of the species tara, molle and casuarina, and profit incorporation in the final sowing of organic matter and soil amendments to facilitate a better development of plants. 3 standard fog collector (SFC) proposed by Schemenauer and Cereceda (1993) were installed and we evaluated the capture water during 31 months, from June 2007 to December 2009, finding much water collected in the winter months, the average annual in the 3 SFC was similar (1.1, 1.2 and 1.1 L m -2 day-1) which allows us to plan according to necessary the best way to harness and store water to supply the plants. It was found that native species, tara and molle were more adaptable to extreme conditions of the place that introduced casuarina species. The tara does grow faster in height and stem diameter, also achieves a good coverage to intercept fog water itself making it more viable and capable

  20. The isotopic composition of valves and organic tissue of diatoms grown in steady state cultures under varying conditions of temperature, light and nutrients. Implications for the interpretation of oxygen isotopes from sedimentary biogenic opal as proxies of environmental variations

    Energy Technology Data Exchange (ETDEWEB)

    Kowalczyk, K

    2006-05-15

    The oxygen isotopes of diatomaceous silica from marine and freshwater sediments are frequently used as indicators of the palaeotemperature development, particularly in cases where calcareous microfossils are rare or absent. With regard to terrestrial waters it is unknown whether or not palaeotemperature scale can be used in a limnic ecosystem. Due to the fact that the seasonal variations in lakes are larger than in oceans, specific problems arise when working with freshwater sediments. Thus, an understanding of the contribution of the various factors (e.g. temperature, light nutrients, competition) influencing the formation of isotope signals in biogenic opal is a prerequisite for the accurate interpretation of environmental processes. Since it is impossible to examine the influence of a single parameter under natural ecosystem conditions due to permanent changes of the environment, laboratory experiments with single diatom species are needed. Therefore, the aim of this study was to investigate the correlation between the oxygen isotope variations in biogenic opal and different environmental parameters using steady state cultures with diatoms. It should be examined whether or not the different diatom species grown under identical conditions show equal oxygen isotope ratios (species relationship), if variations of the water temperature induce variations of the oxygen isotope ratio (relationship with temperature), variable parameters such as light intensity and nitrate concentration influence the isotope ratio, and if vital effects (e.g. growth rate) lead to variations of the oxygen isotope ratio. (orig.)

  1. The isotopic composition of valves and organic tissue of diatoms grown in steady state cultures under varying conditions of temperature, light and nutrients. Implications for the interpretation of oxygen isotopes from sedimentary biogenic opal as proxies of environmental variations

    International Nuclear Information System (INIS)

    Kowalczyk, K.

    2006-05-01

    The oxygen isotopes of diatomaceous silica from marine and freshwater sediments are frequently used as indicators of the palaeotemperature development, particularly in cases where calcareous microfossils are rare or absent. With regard to terrestrial waters it is unknown whether or not palaeotemperature scale can be used in a limnic ecosystem. Due to the fact that the seasonal variations in lakes are larger than in oceans, specific problems arise when working with freshwater sediments. Thus, an understanding of the contribution of the various factors (e.g. temperature, light nutrients, competition) influencing the formation of isotope signals in biogenic opal is a prerequisite for the accurate interpretation of environmental processes. Since it is impossible to examine the influence of a single parameter under natural ecosystem conditions due to permanent changes of the environment, laboratory experiments with single diatom species are needed. Therefore, the aim of this study was to investigate the correlation between the oxygen isotope variations in biogenic opal and different environmental parameters using steady state cultures with diatoms. It should be examined whether or not the different diatom species grown under identical conditions show equal oxygen isotope ratios (species relationship), if variations of the water temperature induce variations of the oxygen isotope ratio (relationship with temperature), variable parameters such as light intensity and nitrate concentration influence the isotope ratio, and if vital effects (e.g. growth rate) lead to variations of the oxygen isotope ratio. (orig.)

  2. Fluctuation of Dof1/Dof2 expression ratio under the influence of varying nitrogen and light conditions: involvement in differential regulation of nitrogen metabolism in two genotypes of finger millet (Eleusine coracana L.).

    Science.gov (United States)

    Gupta, Supriya; Gupta, Sanjay Mohan; Gupta, Alok Kumar; Gaur, Vikram Singh; Kumar, Anil

    2014-08-10

    In order to gain insights into the mechanism of high nitrogen use efficiency (NUE) of finger millet (FM) the role of Dof2 transcription factor (TF), which is a repressor of genes involved in C/N metabolism was investigated. The partial cDNA fragment of EcDof2 (912-bp; GenBank acc. no. KF261117) was isolated and characterized from finger millet (FM) that showed 63% and 58% homology with Dof2 of Zea mays at nucleotide and protein level, respectively. Its expression studies were carried out along with the activator EcDof1 in two genotypes (GE3885, high protein genotype (HPG); GE1437, low protein genotype (LPG)) of FM differing in grain protein contents (13.8% and 6.2%) showed that EcDof2 is expressed in both shoot and root tissues with significantly (p≤0.05) higher expression in the roots. The diurnal expression of both EcDof1 and EcDof2 in shoots was differential having different time of peak expression indicating a differential response to diurnal condition. Under continuous dark conditions, expression of EcDof1 and EcDof2 oscillated in both the genotypes whereas on illumination, the fold expression of EcDof1 was higher as compared to EcDof2. Under increasing nitrate concentration, EcDof2 expression increases in roots and shoots of LPG while it remains unchanged in HPG. However, the EcDof1 expression was found to increase in both genotypes. Further, time kinetics studies under single nitrate concentration revealed that EcDof2 was repressed in the roots of both genotypes whereas EcDof1 oscillated with time. The EcDof1/EcDof2 ratio measured showed differential response under different light and nitrogen conditions. It was higher in the roots of HPG indicating higher activation of genes involved in N uptake and assimilation resulting in high grain protein accumulation. The results indicate that both light and nitrogen concentration influence Dof1 and Dof2 expression and suggests a complex pattern of regulation of genes influenced by these plant specific TFs. In

  3. Informing the development of services supporting self-care for severe, long term mental health conditions: a mixed method study of community based mental health initiatives in England

    Directory of Open Access Journals (Sweden)

    Steve Gillard

    2012-07-01

    Full Text Available Abstract Background Supporting self-care is being explored across health care systems internationally as an approach to improving care for long term conditions in the context of ageing populations and economic constraint. UK health policy advocates a range of approaches to supporting self-care, including the application of generic self-management type programmes across conditions. Within mental health, the scope of self-care remains poorly conceptualised and the existing evidence base for supporting self-care is correspondingly disparate. This paper aims to inform the development of support for self-care in mental health by considering how generic self-care policy guidance is implemented in the context of services supporting people with severe, long term mental health problems. Methods A mixed method study was undertaken comprising standardised psychosocial measures, questionnaires about health service use and qualitative interviews with 120 new referrals to three contrasting community based initiatives supporting self-care for severe, long term mental health problems, repeated nine months later. A framework approach was taken to qualitative analysis, an exploratory statistical analysis sought to identify possible associations between a range of independent variables and self-care outcomes, and a narrative synthesis brought these analyses together. Results Participants reported improvement in self-care outcomes (e.g. greater empowerment; less use of Accident and Emergency services. These changes were not associated with level of engagement with self-care support. Level of engagement was associated with positive collaboration with support staff. Qualitative data described the value of different models of supporting self-care and considered challenges. Synthesis of analyses suggested that timing support for self-care, giving service users control over when and how they accessed support, quality of service user-staff relationships and decision

  4. Ellipsometry with randomly varying polarization states

    NARCIS (Netherlands)

    Liu, F.; Lee, C. J.; Chen, J. Q.; E. Louis,; van der Slot, P. J. M.; Boller, K. J.; F. Bijkerk,

    2012-01-01

    We show that, under the right conditions, one can make highly accurate polarization-based measurements without knowing the absolute polarization state of the probing light field. It is shown that light, passed through a randomly varying birefringent material has a well-defined orbit on the Poincar

  5. Study on initial stage of diesel spray formation. Effects of the condition inside the nozzle sac; Diesel funmu no shoki keisei katei ni kansuru kenkyu. Sac nai nenryo no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, N.; Tsujimura, K. [Nissan Diesel Motor Co. Ltd., Saitama (Japan); Komori, M.

    1996-06-25

    To realize clean diesel exhaust, it is very important to clarify the atomization phenomena of the fuel spray. In this study, the initial stage of the atomization process of a diesel injection fuel spray was analyzed with a high-speed image converter camera under the conditions of atmospheric gas pressure and room temperature. As a result, it was found that the initial spray formation was greatly affected lay the condition inside the nozzle sac. In the case in which fuel existed in the sac, pin-like structure spray formation was observed at the initial injection stage. This phenomenon was not observed in the case in which no fuel was present in the sac, and a widely spread fuel spray formation was observed at the initial injection stage. The relatively low-speed fuel spray injected in the initial low-sac-pressure condition was pushed away by the subsequent fuel spray injected in the high-sac-pressure condition. 7 refs., 12 figs., 1 tab.

  6. Condition varies with habitat choice in postbreeding forest birds

    Science.gov (United States)

    Scott H. Stoleson

    2013-01-01

    Many birds that are experiencing population declines require extensive tracts of mature forest habitat for breeding. Recent work suggests that at least some may shift their habitat use to early-successional areas after nesting but before migration. I used constant-effort mist netting in regenerating clearcuts (4-8 years postcut) and dense mature-forest understories to...

  7. Spectroscopy on metal-halide lamps under varying gravity conditions

    NARCIS (Netherlands)

    Flikweert, A.J.

    2008-01-01

    Worldwide, 20% of all electricity is used for lighting. For this reason, efficient lamps are economically and ecologically important. High intensity discharge (HID) lamps are efficient lamps. The most common HID lamp these days is the metal-halide (MH) lamp. MH lamps have a good colour rendering

  8. Varying Conditions for Hexanoic Acid Degradation with BioTiger™

    Energy Technology Data Exchange (ETDEWEB)

    Foreman, Koji [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Milliken, Charles [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Brigmon, Robin [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-07-27

    BioTiger™ (BT) is a consortium of 12 bacteria designed for petroleum waste biodegradation. BT is currently being studied and could be considered for bioremediation of the Athabasca oil sands refineries in Canada and elsewhere. The run-off ponds from the petroleum extraction processes, called tailings ponds, are a mixture of polycyclic aromatic hydrocarbons, naphthenic acids, hydrocarbons, toxic chemicals like heavy metals, water, and sand. Due to environmental regulations the oil industry would like to separate and degrade the hazardous chemical species from the tailings ponds while recycling the water. It has been shown that BT at 30 C° is able to completely degrade 10 mM hexanoic acid (HA) co-metabolically with 0.2% yeast extract (w/v) in 48 hours when starting at 0.4 OD 600nm. After establishing this stable degradation capability, variations were tested to explore the wider parameters of BT activity in temperature, pH, intermediate degradation, co-metabolic dependence, and transfer stability. Due to the vast differences in temperature at various points in the refineries, a wide range of temperatures were assessed. The results indicate that BT retains the ability to degrade HA, a model surrogate for tailings pond contaminants, at temperatures ranging from 15°C to 35°C. Hexanamide (HAM) was shown to be an intermediate generated during the degradation of HA in an earlier work and HAM is completely degraded after 48 hours, indicating that HAM is not the final product of HA degradation. Various replacements for yeast extract were attempted. Glucose, a carbon source; casein amino acids, a protein source; additional ammonia, mimicking known media; and additional phosphate with Wolffe’s vitamins and minerals all showed no significant degradation of HA compared to control. Decreasing the yeast extract concentration (0.05%) demonstrated limited but significant degradation. Finally, serial inoculations of BT were performed to determine the stability of degradation over several generations. Overall, BT has shown to be moderately flexible for HA co-metabolic biodegradation.

  9. HIV-1 transcripts use IRES-initiation under conditions where Cap-dependent translation is restricted by poliovirus 2A protease.

    Directory of Open Access Journals (Sweden)

    Raquel Amorim

    Full Text Available The 30 different species of mRNAs synthesized during the HIV-1 replication cycle are all capped and polyadenilated. Internal ribosome entry sites have been recognized in the 5' untranslated region of some mRNA species of HIV-1, which would contribute to an alternative mechanism of initiation of mRNA translation. However, the Cap-dependent translation is assumed to be the main mechanism driving the initiation of HIV-1 protein synthesis. In this work, we describe a cell system in which lower to higher levels of transient expression of the poliovirus 2A protease strongly inhibited cellular Cap-dependent translation with no toxic effect to the cells during a 72-hour time frame. In this system, the synthesis of HIV-1 proteins was inhibited in a temporal dose-dependent way. Higher levels of 2A protease expression severely inhibited HIV-1 protein synthesis during the first 24 hours of infection consequently inhibiting viral production and infectivity. Intermediate to lower levels of 2A Protease expression caused the inhibition of viral protein synthesis only during the first 48 hours of viral replication. After this period both protein synthesis and viral release were recovered to the control levels. However, the infectivity of viral progeny was still partially inhibited. These results indicate that two mechanisms of mRNA translation initiation contribute to the synthesis of HIV-1 proteins; during the first 24-48 hours of viral replication HIV-1 protein synthesis is strongly dependent on Cap-initiation, while at later time points IRES-driven translation initiation is sufficient to produce high amounts of viral particles.

  10. THE ENSURING FUNCTIONAL INTERCHANGEABILITY WHEN FORMING THE CONTROL COMPLEX OF INDICATORS OF THE INITIAL CONDITION OF THE CONSUMER OF SPORTS AND IMPROVING SERVICES

    Directory of Open Access Journals (Sweden)

    A. S. Khorloohiyn

    2017-01-01

    Full Text Available One of key elements of an engineering component quality management system of process of provision of sports and improving services in gyms is the subsystem of diagnostics of physical client state. The aim of the study was to increase in efficiency of functioning of a quality management system of process of provision of sports and improving services in gyms due to development of techniques of incorrect estimation of the initial client state.The task of formation of a complex of indices of the initial status by criterion of necessary informtiveness is formulated. The principle of the functional interchangeability as a methodological basis for its decision is reasonable. The hierarchical structure of an integral assessment of the initial client state of gym is offered. On its basis the hierarchical model of rating of informtiveness of a complex of the single (measured indices, the providing objectivity of an integral assessment of the initial status is developed. The correctness of model is provided at the expense of a formulation of a complex of assumptions and original technology of application of different methods of expert estimation.The result of simulation of informtiveness of an integral assessment of the initial client state for a specific type of service and the purposes of physical enhancement includes: 1 library of sets of single indices, for each of which the technique and a monitoring aid, and also an informtiveness assessment in points, 2 the rules of support of the functional interchangeability of alternative complexes of indices by criterion of sufficiency of informtiveness of a complex based on additive models and the accepted restrictions is defined.The concept of a technique of formation of a complex of the measured and (or evaluated indices of the initial client state for the specific type of sports and improving service adapted under material opportunities of gym on the one hand, and responding to criterion of necessary

  11. The determination of the local conditions for void initiation in front of a crack tip for materials with second-phase particles

    Energy Technology Data Exchange (ETDEWEB)

    Sabirov, I. [Erich Schmid Institute of Materials Science, Austrian Academy of Sciences, Jahnstrasse 12, A-8700 Leoben (Austria)]. E-mail: sabirov@unileoben.ac.at; Duschlbauer, D. [Institute of Lightweight Design and Structural Biomechanics, Vienna University of Technology, Gusshausstrasse 27-29, A-1040 Vienna (Austria); Pettermann, H.E. [Institute of Lightweight Design and Structural Biomechanics, Vienna University of Technology, Gusshausstrasse 27-29, A-1040 Vienna (Austria); Kolednik, O. [Erich Schmid Institute of Materials Science, Austrian Academy of Sciences, Jahnstrasse 12, A-8700 Leoben (Austria)

    2005-02-25

    A procedure is proposed to determine, for second-phase particles near a crack tip, the maximum particle stresses at the moment of void initiation by either particle fracture or particle/matrix interface separation. A digital image analysis system is applied to perform a quantitative analysis of corresponding fracture surface regions from stereo image pairs taken in the scanning electron microscope. The fracture surface analysis is used to measure, for individual particles, the crack tip opening displacement at the moment of void initiation and the particle location with respect to the crack tip. From these data, the stress tensor at the moment of void initiation is calculated from the Hutchinson-Rice-Rosengren (HRR) field theory. The corresponding average local stresses within the particle are evaluated by a non-linear Mori-Tanaka-type approach. These stresses are compared to estimates according to the models by Argon et al. [A.S. Argon, J. Im, R. Safoglu, Metall. Trans. 6 (1975) 825] and Beremin [F.M. Beremin, Metall. Trans. 12 (1981) 723]. The procedure is demonstrated on an Al6061-10% Al{sub 2}O{sub 3} metal matrix composite.

  12. Time-varying Crash Risk

    DEFF Research Database (Denmark)

    Christoffersen, Peter; Feunoua, Bruno; Jeon, Yoontae

    We estimate a continuous-time model with stochastic volatility and dynamic crash probability for the S&P 500 index and find that market illiquidity dominates other factors in explaining the stock market crash risk. While the crash probability is time-varying, its dynamic depends only weakly on re...

  13. Eestlased Karlovy Varys / J. R.

    Index Scriptorium Estoniae

    J. R.

    2007-01-01

    Ilmar Raagi mängufilm "Klass" osaleb 42. Karlovy Vary rahvusvahelise filmifestivali võistlusprogrammis "East of the West" ja Asko Kase lühimängufilm "Zen läbi prügi" on valitud festivali kõrvalprogrammi "Forum of Independents"

  14. Esmaklassiline Karlovy Vary / Jaanus Noormets

    Index Scriptorium Estoniae

    Noormets, Jaanus

    2007-01-01

    Ilmar Raagi mängufilm "Klass" võitis 42. Karlovy Vary rahvusvahelise filmifestivalil kaks auhinda - ametliku kõrvalvõistlusprogrammi "East of the West" eripreemia "Special mention" ja Euroopa väärtfilmikinode keti Europa Cinemas preemia. Ka Asko Kase lühifilmi "Zen läbi prügi linastumisest ning teistest auhinnasaajatest ning osalejatest

  15. Optimistlik Karlovy Vary / Jaan Ruus

    Index Scriptorium Estoniae

    Ruus, Jaan, 1938-2017

    2007-01-01

    42. Karlovy Vary rahvusvahelise filmifestivali auhinnatud filmidest (žürii esimees Peter Bart). Kristallgloobuse sai Islandi-Saksamaa "Katseklaasilinn" (režii Baltasar Kormakur), parimaks režissööriks tunnistati norralane Bard Breien ("Negatiivse mõtlemise kunst"). Austraallase Michael James Rowlandi "Hea õnne teekond" sai žürii eripreemia

  16. Characterization of Eosinophil Adhesion to TNF-a-Activated Endothelium Under Flow Conditions: a4 Integrins Mediate Initial Attachment, and E-Selectin Mediates Rolling

    NARCIS (Netherlands)

    Ulfman, L.H.; Kuijper, P.H.M.; Linden, J.A.M. van der; Lammers, J.W.J.; Zwaginga, Jaap Jan; Koenderman, L.

    1999-01-01

    The multistep model of leukocyte adhesion reveals that selectins mediate rolling interactions and that integrins mediate firm adhesion processes. In this study, the interaction between eosinophils and TNF-a-activated HUVEC (second or third passage) was studied under flow conditions (0.8 and 3.2

  17. Initial results from dissolution rate testing of N-Reactor spent fuel over a range of potential geologic repository aqueous conditions

    International Nuclear Information System (INIS)

    Gray, W.J.; Einziger, R.E.

    1998-04-01

    Hanford N-Reactor spent nuclear fuel (HSNF) may ultimately be placed in a geologic repository for permanent disposal. To determine whether the engineered barrier system that will be designed for emplacement of light-water-reactor (LWR) spent fuel will also suffice for HSNF, aqueous dissolution rate measurements were conducted on the HSNF. The purpose of these tests was to determine whether HSNF dissolves faster or slower than LWR spent fuel under some limited repository-relevant water chemistry conditions. The tests were conducted using a flowthrough method that allows the dissolution rate of the uranium matrix to be measured without interference by secondary precipitation reactions that would confuse interpretation of the results. Similar tests had been conducted earlier with LWR spent fuel, thereby allowing direct comparisons. Two distinct corrosion modes were observed during the course of these 12 tests. The first, Stage 1, involved no visible corrosion of the test specimen and produced no undissolved corrosion products. The second, Stage 2, resulted in both visible corrosion of the test specimen and left behind undissolved corrosion products. During Stage 1, the rate of dissolution could be readily determined because the dissolved uranium and associated fission products remained in solution where they could be quantitatively analyzed. The measured rates were much faster than has been observed for LWR spent fuel under all conditions tested to date when normalized to the exposed test specimen surface areas. Application of these results to repository conditions, however, requires some comparison of the physical conditions of the different fuels. The surface area of LWR fuel that could potentially be exposed to repository groundwater is estimated to be approximately 100 times greater than HSNF. Therefore, when compared on the basis of mass, which is more relevant to repository conditions, the HSNF and LWR spent fuel dissolve at similar rates

  18. Variáveis relacionadas à iniciação do tabagismo entre estudantes do ensino médio de escola pública e particular na cidade de Belém - PA Variables related to smoking initiation among students in public and private high schools in the city of Belém, Brazil

    Directory of Open Access Journals (Sweden)

    Denise da Silva Pinto

    2007-10-01

    Full Text Available OBJETIVO: Analisar as variáveis relacionadas à iniciação do tabagismo entre adolescentes estudantes de nível médio de uma escola particular e outra pública, na cidade de Belém-PA, em 2005. MÉTODOS: Para a coleta de dados, foi utilizado um questionário não identificado, de autopreenchimento, com 27 questões fechadas, sobre experimentação de cigarro, fumo habitual, acesso à compra de cigarros, motivo para a experimentação do fumo, autopercepção sobre o seu rendimento escolar, diálogo sobre tabagismo no ambiente familiar e nível sócio-econômico. Participaram do estudo 1520 estudantes, sendo 724 (47,6% da rede particular e 796 (52,4% da rede pública. RESULTADOS: A média de idade dos estudantes foi de 16,5 anos. Dos 1520 estudantes, 669 (44% referiram ter experimentado cigarro e 11% faziam uso habitual de cigarros. A proporção de experimentadores na escola pública foi de 51,2% e na particular foi de 36,7% (p = 0; a de fumantes habituais foi 14,6% na escola pública e de 7% na particular (p = 0. As associações encontradas para iniciação e uso atual de cigarro em ambas as escolas foram: curiosidade, presença de pessoas fumantes no convívio social do adolescente, não ter sido elogiado por não fumar, e se considerar um aluno regular ou ruim. Não houve associação entre experimentação e fumo atual com classes sociais nas duas escolas, exceto para experimentadores das classes A e B na escola particular. CONCLUSÕES: A variável mais importante para fumo entre os estudantes foi a curiosidade. A experimentação e uso habitual de cigarro foram mais freqüentes na escola pública que na particular.OBJETIVE: To analyze the variables related to smoking initiation among adolescent students in two high schools (one public and one private in the city of Belém, Brazil, in 2005. METHODS: An anonymous self-report questionnaire - comprising 27 closed questions regarding smoking experimentation, smoking habit, access to buying

  19. Connecting the dots: Semi-analytical and random walk numerical solutions of the diffusion–reaction equation with stochastic initial conditions

    Energy Technology Data Exchange (ETDEWEB)

    Paster, Amir, E-mail: paster@tau.ac.il [Environmental Fluid Mechanics Laboratories, Dept. of Civil and Environmental Engineering and Earth Sciences, University of Notre Dame, Notre Dame, IN (United States); School of Mechanical Engineering, Tel Aviv University, Tel Aviv, 69978 (Israel); Bolster, Diogo [Environmental Fluid Mechanics Laboratories, Dept. of Civil and Environmental Engineering and Earth Sciences, University of Notre Dame, Notre Dame, IN (United States); Benson, David A. [Hydrologic Science and Engineering, Colorado School of Mines, Golden, CO, 80401 (United States)

    2014-04-15

    We study a system with bimolecular irreversible kinetic reaction A+B→∅ where the underlying transport of reactants is governed by diffusion, and the local reaction term is given by the law of mass action. We consider the case where the initial concentrations are given in terms of an average and a white noise perturbation. Our goal is to solve the diffusion–reaction equation which governs the system, and we tackle it with both analytical and numerical approaches. To obtain an analytical solution, we develop the equations of moments and solve them approximately. To obtain a numerical solution, we develop a grid-less Monte Carlo particle tracking approach, where diffusion is modeled by a random walk of the particles, and reaction is modeled by annihilation of particles. The probability of annihilation is derived analytically from the particles' co-location probability. We rigorously derive the relationship between the initial number of particles in the system and the amplitude of white noise represented by that number. This enables us to compare the particle simulations and the approximate analytical solution and offer an explanation of the late time discrepancies. - Graphical abstract:.

  20. High-Order Weno Simulations of Three-Dimensional Reshocked Richtmyer-Meshkov Instability to Late Times: Dynamics, Dependence on Initial Conditions, and Comparisons to Experimental Data

    Energy Technology Data Exchange (ETDEWEB)

    Schilling, O; Latini, M

    2010-01-12

    The dynamics of the reshocked multi-mode Richtmyer-Meshkov instability is investigated using 513 x 257{sup 2} three-dimensional ninth-order weighted essentially nonoscillatory shock-capturing simulations. A two-mode initial perturbation with superposed random noise is used to model the Mach 1.5 air/SF{sub 6} Vetter-Sturtevant shock tube experiment. The mass fraction and enstrophy isosurfaces, and density cross-sections are utilized to show the detailed flow structure before, during, and after reshock. It is shown that the mixing layer growth agrees well with the experimentally measured growth rate before and after reshock. The post-reshock growth rate is also in good agreement with the prediction of the Mikaelian model. A parametric study of the sensitivity of the layer growth to the choice of amplitudes of the short and long wavelength initial interfacial perturbation is also presented. Finally, the amplification effects of reshock are quantified using the evolution of the turbulent kinetic energy and turbulent enstrophy spectra, as well as the evolution of the baroclinic enstrophy production, buoyancy production, and shear production terms in the enstrophy and turbulent kinetic transport equations.

  1. Genetic polymorphisms in varied environments.

    Science.gov (United States)

    Powell, J R

    1971-12-03

    Thirteen experimenital populationis of Drosophila willistoni were maintained in cages, in some of which the environments were relatively constant and in others varied. After 45 weeks, the populations were assayed by gel electrophoresis for polymorphisms at 22 protein loci. The average heterozygosity per individual and the average unmber of alleles per locus were higher in populations maintained in heterogeneous environments than in populations in more constant enviroments.

  2. Computational issues of solving the 1D steady gradually varied flow equation

    Directory of Open Access Journals (Sweden)

    Artichowicz Wojciech

    2014-09-01

    Full Text Available In this paper a problem of multiple solutions of steady gradually varied flow equation in the form of the ordinary differential energy equation is discussed from the viewpoint of its numerical solution. Using the Lipschitz theorem dealing with the uniqueness of solution of an initial value problem for the ordinary differential equation it was shown that the steady gradually varied flow equation can have more than one solution. This fact implies that the nonlinear algebraic equation approximating the ordinary differential energy equation, which additionally coincides with the wellknown standard step method usually applied for computing of the flow profile, can have variable number of roots. Consequently, more than one alternative solution corresponding to the same initial condition can be provided. Using this property it is possible to compute the water flow profile passing through the critical stage.

  3. Spatially varying dispersion to model breakthrough curves.

    Science.gov (United States)

    Li, Guangquan

    2011-01-01

    Often the water flowing in a karst conduit is a combination of contaminated water entering at a sinkhole and cleaner water released from the limestone matrix. Transport processes in the conduit are controlled by advection, mixing (dilution and dispersion), and retention-release. In this article, a karst transport model considering advection, spatially varying dispersion, and dilution (from matrix seepage) is developed. Two approximate Green's functions are obtained using transformation of variables, respectively, for the initial-value problem and for the boundary-value problem. A numerical example illustrates that mixing associated with strong spatially varying conduit dispersion can cause strong skewness and long tailing in spring breakthrough curves. Comparison of the predicted breakthrough curve against that measured from a dye-tracing experiment between Ames Sink and Indian Spring, Northwest Florida, shows that the conduit dispersivity can be as large as 400 m. Such a large number is believed to imply strong solute interaction between the conduit and the matrix and/or multiple flow paths in a conduit network. It is concluded that Taylor dispersion is not dominant in transport in a karst conduit, and the complicated retention-release process between mobile- and immobile waters may be described by strong spatially varying conduit dispersion. Copyright © 2010 The Author(s). Journal compilation © 2010 National Ground Water Association.

  4. Model simulation studies to clarify the effect on saccadic eye movements of initial condition velocities set by the Vestibular Ocular Reflex (VOR)

    Science.gov (United States)

    Nam, M. H.; Winters, J. M.; Stark, L.

    1981-01-01

    Voluntary active head rotations produced vestibulo-ocular reflex eye movements (VOR) with the subject viewing a fixation target. When this target jumped, the size of the refixation saccades were a function of the ongoing initial velocity of the eye. Saccades made against the VOR were larger in magnitude. Simulation of a reciprocally innervated model eye movement provided results comparable to the experimental data. Most of the experimental effect appeared to be due to linear summation for saccades of 5 and 10 degree magnitude. For small saccades of 2.5 degrees, peripheral nonlinear interaction of state variables in the neuromuscular plant also played a role as proven by comparable behavior in the simulated model with known controller signals.

  5. The Thermal Collector With Varied Glass Covers

    International Nuclear Information System (INIS)

    Luminosu, I.; Pop, N.

    2010-01-01

    The thermal collector with varied glass covers represents an innovation realized in order to build a collector able to reach the desired temperature by collecting the solar radiation from the smallest surface, with the highest efficiency. In the case of the thermal collector with variable cover glasses, the number of the glass plates covering the absorber increases together with the length of the circulation pipe for the working fluid. The thermal collector with varied glass covers compared to the conventiona