Experimental study on the critical heat flux in a varying acceleration field, (1)

International Nuclear Information System (INIS)

Kusunoki, Tsuyoshi; Yokomura, Takeyoshi; Otsuji, Tomoo; Ikawa, Masahiro; Kurosawa, Akira.

1988-12-01

It is very important for the thermohydraulic design and for the safety assesement of marine reactors, to understand the effect of varying acceleration induced by ship motion on critical heart flux. The purpose of this joint study is to examine quantitatively the influence of varying acceleration on the behavior of bubbles. In the experiment, FREON-113 was used as working fluid. This report describes some experimental results; measurements of void fraction and bubble velocity near the heat transfer surface, measurement of bubble size under stationary acceleration field and observation of bubble behavior under varying acceleration field. (author)

One-dimensional radionuclide transport under time-varying conditions

International Nuclear Information System (INIS)

Gelbard, F.; Olague, N.E.; Longsine, D.E.

1990-01-01

This paper discusses new analytical and numerical solutions presented for one-dimensional radionuclide transport under time-varying fluid-flow conditions including radioactive decay. The analytical solution assumes that all radionuclides have identical retardation factors, and is limited to instantaneous releases. The numerical solution does not have these limitations, but is tested against the limiting case given for the analytical solution. Reasonable agreement between the two solutions was found. Examples are given for the transport of a three-member radionuclide chain transported over distances and flow rates comparable to those reported for Yucca Mountain, the proposed disposal site for high-level nuclear waste

Evaluation of new reference genes in papaya for accurate transcript normalization under different experimental conditions.

Directory of Open Access Journals (Sweden)

Xiaoyang Zhu

Full Text Available Real-time reverse transcription PCR (RT-qPCR is a preferred method for rapid and accurate quantification of gene expression studies. Appropriate application of RT-qPCR requires accurate normalization though the use of reference genes. As no single reference gene is universally suitable for all experiments, thus reference gene(s validation under different experimental conditions is crucial for RT-qPCR analysis. To date, only a few studies on reference genes have been done in other plants but none in papaya. In the present work, we selected 21 candidate reference genes, and evaluated their expression stability in 246 papaya fruit samples using three algorithms, geNorm, NormFinder and RefFinder. The samples consisted of 13 sets collected under different experimental conditions, including various tissues, different storage temperatures, different cultivars, developmental stages, postharvest ripening, modified atmosphere packaging, 1-methylcyclopropene (1-MCP treatment, hot water treatment, biotic stress and hormone treatment. Our results demonstrated that expression stability varied greatly between reference genes and that different suitable reference gene(s or combination of reference genes for normalization should be validated according to the experimental conditions. In general, the internal reference genes EIF (Eukaryotic initiation factor 4A, TBP1 (TATA binding protein 1 and TBP2 (TATA binding protein 2 genes had a good performance under most experimental conditions, whereas the most widely present used reference genes, ACTIN (Actin 2, 18S rRNA (18S ribosomal RNA and GAPDH (Glyceraldehyde-3-phosphate dehydrogenase were not suitable in many experimental conditions. In addition, two commonly used programs, geNorm and Normfinder, were proved sufficient for the validation. This work provides the first systematic analysis for the selection of superior reference genes for accurate transcript normalization in papaya under different experimental

Experimental performance evaluation for a carbon dioxide light commercial cooling application under transcritical and subcritical conditions

International Nuclear Information System (INIS)

Boccardi, G.; Calabrese, N.; Celata, G.P.; Mastrullo, R.; Mauro, A.W.; Perrone, A.; Trinchieri, R.

2013-01-01

CO 2 is one of the most interesting non toxic, nor flammable, low GWP natural fluid to be used in applications with a large direct contribution to global warming, such as vending machines. In this paper the results of an experimental investigation on a small capacity, air-forced refrigerating plant working with CO 2 are presented. The air inlet temperatures at gas cooler and evaporator were varied between 16 °C and 31 °C and between −25 °C and 25 °C, respectively, to cover the range of temperatures under conditions typical of commercial refrigeration, during quasi-steady operation. The thermodynamic analysis of the system performance was carried on varying independently the pressure at the gas cooler, by overfeeding the liquid receiver to point out the effect of refrigerant charge. The results allow to describe the performance of the system in a map varying the boundary conditions; at the same time the corresponding variations of the thermodynamic cycle, the COP and the mass flow rate are reported. -- Highlights: ► A light commercial refrigerating plant working with CO 2 was tested in order to evaluate its performance. ► 71 experimental points were collected varying the flow rates, the temperatures of air sources and the refrigerant charge. ► Mass flow rate, cooling capacity, electrical power and COP were evaluated as a function of pressures and superheating. ► The segregate influence of each operating parameter on each performance indicator was calculated. ► A map of plant performance as a function of air source temperatures is reported

The effect of bedload transport rates on bedform and planform morphological development in a laboratory meandering stream under varying flow conditions

Science.gov (United States)

Sullivan, C.; Good, R. G. R.; Binns, A. D.

2017-12-01

Sediment transport processes in streams provides valuable insight into the temporal evolution of planform and bedform geometry. The majority of previous experimental research in the literature has focused on bedload transport and corresponding bedform development in rectangular, confined channels, which does not consider planform adjustment processes in streams. In contrast, research conducted with laboratory streams having movable banks can investigate planform development in addition to bedform development, which is more representative of natural streams. The goal of this research is to explore the relationship between bedload transport rates and the morphological adjustments in meandering streams. To accomplish this, a series of experimental runs were conducted in a 5.6 m by 1.9 m river basin flume at the University of Guelph to analyze the bedload impacts on bed formations and planform adjustments in response to varying flow conditions. In total, three experimental runs were conducted: two runs using steady state conditions and one run using unsteady flow conditions in the form of a symmetrical hydrograph implementing quasi steady state flow. The runs were performed in a series of time-steps in order to monitor the evolution of the stream morphology and the bedload transport rates. Structure from motion (SfM) was utilized to capture the channel morphology after each time-step, and Agisoft PhotoScan software was used to produce digital elevation models to analyze the morphological evolution of the channel with time. Bedload transport rates were quantified using a sediment catch at the end of the flume. Although total flow volumes were similar for each run, the morphological evolution and bedload transport rates in each run varied. The observed bedload transport rates from the flume are compared with existing bedload transport formulas to assess their accuracy with respect to sediment transport in unconfined meandering channels. The measured sediment transport

Atmospheric particle formation in spatially and temporally varying conditions

Energy Technology Data Exchange (ETDEWEB)

Lauros, J.

2011-07-01

Atmospheric particles affect the radiation balance of the Earth and thus the climate. New particle formation from nucleation has been observed in diverse atmospheric conditions but the actual formation path is still unknown. The prevailing conditions can be exploited to evaluate proposed formation mechanisms. This study aims to improve our understanding of new particle formation from the view of atmospheric conditions. The role of atmospheric conditions on particle formation was studied by atmospheric measurements, theoretical model simulations and simulations based on observations. Two separate column models were further developed for aerosol and chemical simulations. Model simulations allowed us to expand the study from local conditions to varying conditions in the atmospheric boundary layer, while the long-term measurements described especially characteristic mean conditions associated with new particle formation. The observations show statistically significant difference in meteorological and back-ground aerosol conditions between observed event and non-event days. New particle formation above boreal forest is associated with strong convective activity, low humidity and low condensation sink. The probability of a particle formation event is predicted by an equation formulated for upper boundary layer conditions. The model simulations call into question if kinetic sulphuric acid induced nucleation is the primary particle formation mechanism in the presence of organic vapours. Simultaneously the simulations show that ignoring spatial and temporal variation in new particle formation studies may lead to faulty conclusions. On the other hand, the theoretical simulations indicate that short-scale variations in temperature and humidity unlikely have a significant effect on mean binary water sulphuric acid nucleation rate. The study emphasizes the significance of mixing and fluxes in particle formation studies, especially in the atmospheric boundary layer. The further

Sex differences in in-group cooperation vary dynamically with competitive conditions and outcomes.

Science.gov (United States)

Bailey, Drew H; Winegard, Benjamin; Oxford, Jon; Geary, David C

2012-03-18

Men's but not women's investment in a public goods game varied dynamically with the presence or absence of a perceived out-group. Three hundred fifty-four (167 male) young adults participated in multiple iterations of a public goods game under intergroup and individual competition conditions. Participants received feedback about whether their investments in the group were sufficient to earn a bonus to be shared among all in-group members. Results for the first trial confirm previous research in which men's but not women's investments were higher when there was a competing out-group. We extended these findings by showing that men's investment in the in-group varied dynamically by condition depending on the outcome of the previous trial: In the group condition, men, but not women, decreased spending following a win (i.e., earning an in-group bonus). In the individual condition, men, but not women, increased spending following a win. We hypothesize that these patterns reflect a male bias to calibrate their level of in-group investment such that they sacrifice only what is necessary for their group to successfully compete against a rival group.

Sex Differences in In-Group Cooperation Vary Dynamically with Competitive Conditions and Outcomes

Directory of Open Access Journals (Sweden)

Drew H. Bailey

2012-01-01

Full Text Available Men's but not women's investment in a public goods game varied dynamically with the presence or absence of a perceived out-group. Three hundred fifty-four (167 male young adults participated in multiple iterations of a public goods game under intergroup and individual competition conditions. Participants received feedback about whether their investments in the group were sufficient to earn a bonus to be shared among all in-group members. Results for the first trial confirm previous research in which men's but not women's investments were higher when there was a competing out-group. We extended these findings by showing that men's investment in the in-group varied dynamically by condition depending on the outcome of the previous trial: In the group condition, men, but not women, decreased spending following a win (i.e., earning an in-group bonus. In the individual condition, men, but not women, increased spending following a win. We hypothesize that these patterns reflect a male bias to calibrate their level of in-group investment such that they sacrifice only what is necessary for their group to successfully compete against a rival group.

Towards artificial intelligence based diesel engine performance control under varying operating conditions using support vector regression

Directory of Open Access Journals (Sweden)

Naradasu Kumar Ravi

2013-01-01

Full Text Available Diesel engine designers are constantly on the look-out for performance enhancement through efficient control of operating parameters. In this paper, the concept of an intelligent engine control system is proposed that seeks to ensure optimized performance under varying operating conditions. The concept is based on arriving at the optimum engine operating parameters to ensure the desired output in terms of efficiency. In addition, a Support Vector Machines based prediction model has been developed to predict the engine performance under varying operating conditions. Experiments were carried out at varying loads, compression ratios and amounts of exhaust gas recirculation using a variable compression ratio diesel engine for data acquisition. It was observed that the SVM model was able to predict the engine performance accurately.

Leading-Edge Noise Prediction of General Airfoil Profiles with Spanwise-Varying Inflow Conditions

NARCIS (Netherlands)

Miotto, Renato Fuzaro; Wolf, William Roberto; De Santana, Leandro Dantas

2018-01-01

This paper presents a study of the leading-edge noise radiated by an airfoil undergoing a turbulent inflow. The noise prediction of generic airfoil profiles subjected to spanwise-varying inflow conditions is performed with the support of Amiet’s theory and the inverse strip technique. In the

Leading-Edge Noise Prediction of General Airfoil Profiles with Spanwise-Varying Inflow Conditions

NARCIS (Netherlands)

Miotto, Renato Fuzaro; Wolf, William Roberto; De Santana, Leandro Dantas

This paper presents a study of the leading-edge noise radiated by an airfoil undergoing a turbulent inflow. The noise prediction of generic airfoil profiles subjected to spanwise-varying inflow conditions is performed with the support of Amiet’s theory and the inverse strip technique. In the

Varied Practice in Laparoscopy Training: Beneficial Learning Stimulation or Cognitive Overload?

Science.gov (United States)

Spruit, Edward N; Kleijweg, Luca; Band, Guido P H; Hamming, Jaap F

2016-01-01

Determining the optimal design for surgical skills training is an ongoing research endeavor. In education literature, varied practice is listed as a positive intervention to improve acquisition of knowledge and motor skills. In the current study we tested the effectiveness of a varied practice intervention during laparoscopy training. Twenty-four trainees (control group) without prior experience received a 3 weeks laparoscopic skills training utilizing four basic and one advanced training task. Twenty-eight trainees (experimental group) received the same training with a random training task schedule, more frequent task switching and inverted viewing conditions on the four basic training tasks, but not the advanced task. Results showed inferior performance of the experimental group on the four basic laparoscopy tasks during training, at the end of training and at a 2 months retention session. We assume the inverted viewing conditions have led to the deterioration of learning in the experimental group because no significant differences were found between groups on the only task that had not been practiced under inverted viewing conditions; the advanced laparoscopic task. Potential moderating effects of inter-task similarity, task complexity, and trainee characteristics are discussed.

Varied Practice in Laparoscopy Training: Beneficial Learning Stimulation or Cognitive Overload?

Directory of Open Access Journals (Sweden)

Edward N. eSpruit

2016-05-01

Full Text Available AbstractDetermining the optimal design for surgical skills training is an ongoing research endeavor. In education literature, varied practice is listed as a positive intervention to improve acquisition of knowledge and motor skills. In the current study we tested the effectiveness of a varied practice intervention during laparoscopy training. 24 trainees (control group without prior experience received a three week laparoscopic skills training utilizing four basic and one advanced training task. 28 trainees (experimental group received the same training with a random training task schedule, more frequent task switching and inverted viewing conditions on the four basic training tasks, but not the advanced task. Results showed inferior performance of the experimental group on the four basic laparoscopy tasks during training, at the end of training and at a two month retention session. We assume the inverted viewing conditions have led to the deterioration of learning in the experimental group because no significant differences were found between groups on the only task that had not been practiced under inverted viewing conditions; the advanced laparoscopic task. Potential moderating effects of inter-task similarity, task complexity and trainee characteristics are discussed.

Applicability of common stomatal conductance models in maize under varying soil moisture conditions.

Science.gov (United States)

Wang, Qiuling; He, Qijin; Zhou, Guangsheng

2018-07-01

In the context of climate warming, the varying soil moisture caused by precipitation pattern change will affect the applicability of stomatal conductance models, thereby affecting the simulation accuracy of carbon-nitrogen-water cycles in ecosystems. We studied the applicability of four common stomatal conductance models including Jarvis, Ball-Woodrow-Berry (BWB), Ball-Berry-Leuning (BBL) and unified stomatal optimization (USO) models based on summer maize leaf gas exchange data from a soil moisture consecutive decrease manipulation experiment. The results showed that the USO model performed best, followed by the BBL model, BWB model, and the Jarvis model performed worst under varying soil moisture conditions. The effects of soil moisture made a difference in the relative performance among the models. By introducing a water response function, the performance of the Jarvis, BWB, and USO models improved, which decreased the normalized root mean square error (NRMSE) by 15.7%, 16.6% and 3.9%, respectively; however, the performance of the BBL model was negative, which increased the NRMSE by 5.3%. It was observed that the models of Jarvis, BWB, BBL and USO were applicable within different ranges of soil relative water content (i.e., 55%-65%, 56%-67%, 37%-79% and 37%-95%, respectively) based on the 95% confidence limits. Moreover, introducing a water response function, the applicability of the Jarvis and BWB models improved. The USO model performed best with or without introducing the water response function and was applicable under varying soil moisture conditions. Our results provide a basis for selecting appropriate stomatal conductance models under drought conditions. Copyright © 2018 Elsevier B.V. All rights reserved.

Understanding and simulating vibrations of plain bridge cables under varying meteorological conditions

DEFF Research Database (Denmark)

Matteoni, Giulia

amplitude peak to peak amplitudes, occurred. This latter behaviour was likely to be associated to dry inclined galloping. Passive dynamic wind tunnel tests were finally undertaken in presence of rain, using the same cable model as adopted in the dry state. The tests served to improve the current......The dissertation investigates the phenomenon of wind induced vibration of bridge cables under varying meteorological conditions. A twin research approach is adopted, where wind tunnel investigation of full-scale bridge cable section models is paralleled with theoretical modelling. A literature......-scale monitoring, wind tunnel testing and theoretical modelling. An extensive wind tunnel test campaign was then undertaken in order to further understand the onset conditions and characteristics of instability in the different climatic conditions described in the literature. Tests were separated into two...

Experimental evaluation of automotive air-conditioning using HFC-134a and HC-134a

Science.gov (United States)

Nasution, Henry; Zainudin, Muhammad Amir; Aziz, Azhar Abdul; Latiff, Zulkarnain Abdul; Perang, Mohd Rozi Mohd; Rahman, Abd Halim Abdul

2012-06-01

An experimental study to evaluate the energy consumption of an automotive air conditioning is presented. In this study, these refrigerants will be tested using the experimental rig which simulated the actual cars as a cabin complete with a cooling system component of the actual car that is as the blower, evaporator, condenser, radiators, electric motor, which acts as a vehicle engine, and then the electric motor will operate the compressor using a belt and pulley system, as well as to the alternator will recharge the battery. The compressor working with the fluids HFC-134a and HC-134a and has been tested varying the speed in the range 1000, 1500, 2000 and 2500 rpm. The measurements taken during the one hour experimental periods at 2-minutes interval times for temperature setpoint of 20°C with internal heat loads 0, 500, 700 and 1000 W. The final results of this study show an overall better energy consumption of the HFC-134a compared with the HC-134a.

A SVDD and K-Means Based Early Warning Method for Dual-Rotor Equipment under Time-Varying Operating Conditions

Directory of Open Access Journals (Sweden)

Zhinong Jiang

2018-01-01

Full Text Available Under frequently time-varying operating conditions, equipment with dual rotors like gas turbines is influenced by two rotors with different rotating speeds. Alarm methods of fixed threshold are unable to consider the influences of time-varying operating conditions. Hence, those methods are not suitable for monitoring dual-rotor equipment. An early warning method for dual-rotor equipment under time-varying operating conditions is proposed in this paper. The influences of time-varying rotating speeds of dual rotors on alarm thresholds have been considered. Firstly, the operating conditions are divided into several limited intervals according to rotating speeds of dual rotors. Secondly, the train data within each interval is processed by SVDD and the allowable ranges (i.e., the alarm threshold of the vibration are determined. The alarm threshold of each interval of operating conditions is obtained. The alarm threshold can be expressed as a sphere, whose controlling parameters are the coordinate of the center and the radius. Then, the cluster center of the test data, whose alarm state is to be judged, can be extracted through K-means. Finally, the alarm state can be obtained by comparing the cluster center with the corresponding sphere. Experiments are conducted to validate the proposed method.

Counterbalancing for serial order carryover effects in experimental condition orders

OpenAIRE

Brooks, Joseph L

2012-01-01

Reactions of neural, psychological, and social systems are rarely, if ever, independent of previous inputs and states. The potential for serial order carryover effects from one condition to the next in a sequence of experimental trials makes counterbalancing of condition order an essential part of experimental design. Here, a method is proposed for generating counterbalanced sequences for repeated-measures designs including those with multiple observations of each condition on one participant...

Counterbalancing for Serial Order Carryover Effects in Experimental Condition Orders

Science.gov (United States)

Brooks, Joseph L.

2012-01-01

Reactions of neural, psychological, and social systems are rarely, if ever, independent of previous inputs and states. The potential for serial order carryover effects from one condition to the next in a sequence of experimental trials makes counterbalancing of condition order an essential part of experimental design. Here, a method is proposed…

Varying the number of bidders in the first-price sealed-bid auction: experimental evidence for the one-shot game

NARCIS (Netherlands)

Füllbrunn, S.C.; Neugebauer, T.

2013-01-01

The paper reports experimental data on the behavior in the first-price sealed-bid auction for a varying number of bidders when values and bids are private information. This feedback-free design is proposed for the experimental test of the one-shot game situation. We consider both within-subjects and

Experimental analysis of the thermal entrainment factor of air curtains in vertical open display cabinets for different ambient air conditions

International Nuclear Information System (INIS)

Gaspar, Pedro Dinis; Carrilho Goncalves, L.C.; Pitarma, R.A.

2011-01-01

The vertical open refrigerated display cabinets suffer alterations of their thermal performance and energy efficiency due to variations of ambient air conditions. The air curtain provides an aerothermodynamics insulation effect that can be evaluated by the thermal entrainment factor calculation as an engineering approximation or by the calculus of all sensible and latent thermal loads. This study presents the variation of heat transfer rate and thermal entrainment factor obtained through experimental tests carried out for different ambient air conditions, varying air temperature, relative humidity, velocity and its direction relatively to the display cabinet frontal opening. The thermal entrainment factor are analysed and compared with the total sensible and latent heats results for the experimental tests. From an engineering point of view, it is concluded that thermal entrainment factor cannot be used indiscriminately, although its use is suitable to design better cabinet under the same climate class condition.

Globally exponential stability condition of a class of neural networks with time-varying delays

International Nuclear Information System (INIS)

Liao, T.-L.; Yan, J.-J.; Cheng, C.-J.; Hwang, C.-C.

2005-01-01

In this Letter, the globally exponential stability for a class of neural networks including Hopfield neural networks and cellular neural networks with time-varying delays is investigated. Based on the Lyapunov stability method, a novel and less conservative exponential stability condition is derived. The condition is delay-dependent and easily applied only by checking the Hamiltonian matrix with no eigenvalues on the imaginary axis instead of directly solving an algebraic Riccati equation. Furthermore, the exponential stability degree is more easily assigned than those reported in the literature. Some examples are given to demonstrate validity and excellence of the presented stability condition herein

Improving Delay-Range-Dependent Stability Condition for Systems with Interval Time-Varying Delay

Directory of Open Access Journals (Sweden)

Wei Qian

2013-01-01

Full Text Available This paper discusses the delay-range-dependent stability for systems with interval time-varying delay. Through defining the new Lyapunov-Krasovskii functional and estimating the derivative of the LKF by introducing new vectors, using free matrices and reciprocally convex approach, the new delay-range-dependent stability conditions are obtained. Two well-known examples are given to illustrate the less conservatism of the proposed theoretical results.

Experimental Observations of Natural Circulation Flow in the NSTF at Steady-State Conditions

International Nuclear Information System (INIS)

Lisowski, Darius D.; Farmer, Mitch T.

2014-01-01

A ½ scale test facility has been constructed at Argonne National Laboratory (ANL) to study the heat removal performance and natural circulation flow patterns in a Reactor Cavity Cooling System (RCCS). Our test facility, the Natural convection Shutdown heat removal Test Facility (NSTF), supports the broader goal of developing an inherently safe and fully passive ex-vessel decay heat removal for advanced reactor designs. The project, initiated in 2010 to support the Advanced Reactor Concepts (ARC), Small Modular Reactor (SMR), and Next Generation Nuclear Plant (NGNP) programs, has been conducting experimental operations since early 2014. The following paper provides a summary of some primary design features of the 26-m tall test facility along with a description of the data acquisition suite that guides our experimental practices. Specifics of the distributed fiber optic temperature measurements will be discussed, which introduces an unparalleled level of data density that has never before been implemented in a large scale natural circulation test facility. Results from our first test series will then be presented, which provide insight into the thermal hydraulic behavior at steady-state conditions for varying heat flux levels and exhaust chimney configuration states. (author)

Assessment of a surface-layer parameterization scheme in an atmospheric model for varying meteorological conditions

Directory of Open Access Journals (Sweden)

T. J. Anurose

2014-06-01

Full Text Available The performance of a surface-layer parameterization scheme in a high-resolution regional model (HRM is carried out by comparing the model-simulated sensible heat flux (H with the concurrent in situ measurements recorded at Thiruvananthapuram (8.5° N, 76.9° E, a coastal station in India. With a view to examining the role of atmospheric stability in conjunction with the roughness lengths in the determination of heat exchange coefficient (CH and H for varying meteorological conditions, the model simulations are repeated by assigning different values to the ratio of momentum and thermal roughness lengths (i.e. z0m/z0h in three distinct configurations of the surface-layer scheme designed for the present study. These three configurations resulted in differential behaviour for the varying meteorological conditions, which is attributed to the sensitivity of CH to the bulk Richardson number (RiB under extremely unstable, near-neutral and stable stratification of the atmosphere.

Experimental and theoretical study on natural circulation capacity under rolling motion condition

International Nuclear Information System (INIS)

Tan Sichao; Gao Puzhen

2007-01-01

Effect of rolling motion on natural circulation capacity was studied experimentally and theoretically. Experiments were conducted under the conditions of rolling and unrolling motions. The experimental results show that natural circulation capacity decreases under rolling motion condition. A mathematic model was developed to calculate the natural circulation capacity under rolling motion condition, considering the characteristics of natural circulation, the model was modified. The calculated results agree with experimental data well. Effect of rolling motion on natural circulation was analyzed through calculation and the following conclusions were obtained: (1) The increase of flow resistance coefficient is the main reason that the natural circulation capacity decreases under rolling motion condition; (2) Non-uniform distribution of fluid mass in the pipe has also influence on natural circulation capacity. (author)

Experimental investigation on a coupled solar still under desert climatic conditions

International Nuclear Information System (INIS)

Boukar, M.; Harmim, A.

2000-01-01

Distillation of water is energy intensive, and the use of solar energy for this purpose has been quite well developed and applied in many places. The performance of a simple basin greenhouse-type solar still coupled to a flat plate collector is experimentally investigated. The Saharan sites of Algeria enjoys bright sunshine and dry weather during most part of year. The objective of the work is to improve the performances of a simple single basin solar still, we test the distillation system in winter, under desert climatic conditions, to improve the quality and increase the quantity of distilled water, by using a solar collector for increasing the brine temperature, enhancing the evaporation process of a simple solar still and improving distillate collection process. Experiments have been conducted in Adrar, Algerian desert town (27 degree 18' N, latitude, 0 degree 17' W longitude). The daily still productivity in winter period varies from 4.5 l/m 2 /day to 5.3 l/m 2 /day with variation of water level from 1.5 cm to 3.5 cm. (Author)

Experimental evidence for amplitude death induced by a time-varying interaction

Energy Technology Data Exchange (ETDEWEB)

Suresh, K. [Centre for Nonlinear Dynamics, School of Physics, Bharathidasan University, Tiruchirappalli 620024, Tamil Nadu (India); Shrimali, M.D. [Department of Physics, Central University of Rajasthan, NH-8, Bandar Sindri, Ajmer 305 801 (India); Prasad, Awadhesh [Department of Physics and Astrophysics, University of Delhi, Delhi 110 007 (India); Thamilmaran, K., E-mail: maran.cnld@gmail.com [Centre for Nonlinear Dynamics, School of Physics, Bharathidasan University, Tiruchirappalli 620024, Tamil Nadu (India)

2014-08-01

In this paper, we study the time-varying interaction in coupled oscillatory systems. For this purpose, we have designed a novel time-varying resistive network using an analog switch and inverter circuits. We have applied this time-varying resistive network to mutually coupled identical Chua's oscillators. When the resistances are varied in time, we find that amplitude death arises in coupled identical oscillators. This has been observed numerically as well as verified through hardware experiments. - Highlights: • We have implemented the time-varying interaction in coupled oscillatory systems. • We have designed a novel time-varying resistive network using an analog switch and inverter circuits. • When the resistances are varied in time, we find that amplitude death arises in coupled identical oscillators.

An experimental study of soil temperature regimes associated with solar disinfestation techniques under greenhouse conditions in Greece.

Science.gov (United States)

Garofalakis, I; Tsiros, I; Frangoudakis, A; Chronopoulos, K; Flouri, F

2006-01-01

This paper deals with an experimental study of various techniques that have been applied for soil disinfestation purposes under greenhouse conditions. Various meteorological parameters and soil temperatures were measured for four different experimental soil segments (three associated with different disinfestation techniques and one as a reference) at depths varying between 0-1 m and with a time interval of 5 min in a greenhouse located in the Agricultural University of Athens Campus, Greece. Results showed that plastic polyethylene films such as covers, metallic conductors or a combination of both were able to enhance heat transfer and temperature increase in greenhouse soil. For typical disinfestation conditions, the depth-averaged temperature values for plastic covers, metallic conductors, and the combination of both were found to be higher than those for the reference of about 5 degrees C, 12 degrees C and 15 micro C, respectively. Moreover, the remained population percentages 50 days after the initiation of the experiment were found to be 19.3%, 25.3%, 37.3% Kcat 94% of the initial population, for the combination of metallic conductors and plastic covers, metallic conductors, plastic cover, and for the reference, respectively.

Varying the number of bidders in the first-price sealed-bid auction: experimental evidence for the one-shot game

OpenAIRE

Tibor Neugebauer; Sascha F llbrunn

2013-01-01

The paper reports experimental data on the behavior in the first-price sealed-bid auction for a varying number of bidders when values and bids are private information. This feedback-free design is proposed for the experimental test of the one-shot game situation. We consider both within-subject and betweensubjects variations. In line with the qualitative risk neutral Nash equilibrium prediction, the data show that bids increase in the number of bidders. However, in auctions involving a small ...

Pollinator effectiveness varies with experimental shifts in flowering time.

Science.gov (United States)

Rafferty, Nicole E; Ives, Anthony R

2012-04-01

The earlier flowering times exhibited by many plant species are a conspicuous sign of climate change. Altered phenologies have caused concern that species could suffer population declines if they flower at times when effective pollinators are unavailable. For two perennial wildflowers, Tradescantia ohiensis and Asclepias incarnata, we used an experimental approach to explore how changing phenology affects the taxonomic composition of the pollinator assemblage and the effectiveness of individual pollinator taxa. After finding in the previous year that fruit set varied with flowering time, we manipulated flowering onset in greenhouses, placed plants in the field over the span of five weeks, and measured pollinator effectiveness as the number of seeds produced after a single visit to a flower. The average effectiveness of pollinators and the expected rates of pollination success were lower for plants of both species flowering earlier than for plants flowering at historical times, suggesting there could be reproductive costs to earlier flowering. Whereas for A. incarnata, differences in average seed set among weeks were due primarily to changes in the composition of the pollinator assemblage, the differences for T. ohiensis were driven by the combined effects of compositional changes and increases over time in the effectiveness of some pollinator taxa. Both species face the possibility of temporal mismatch between the availability of the most effective pollinators and the onset of flowering, and changes in the effectiveness of individual pollinator taxa through time may add an unexpected element to the reproductive consequences of such mismatches.

Performance of cable-in-conduit conductors in ITER [International Thermonuclear Experimental Reactor] toroidal field coils with varying heat loads

International Nuclear Information System (INIS)

Kerns, J.A.; Wong, R.L.

1989-01-01

The toroidal field (TF) coils in the International Thermonuclear Experimental Reactor (ITER) will operate with varying heat loads generated by ac losses and nuclear heating. The total heat load is estimated to be 2 kW per TF coil under normal operation and can be higher for different operating scenarios. Ac losses are caused by ramping the poloidal field (PF) for plasma initiation, burn, and shutdown; nuclear heating results from neutrons that penetrate into the coil past the shield. Present methods to reduce or eliminate these losses lead to larger and more expensive machines, which are unacceptable with today's budget constraints. A suitable solution is to design superconductors that operate with high heat loads. The cable-in-conduit conductor (CICC) can operate with high heat loads. One CICC design is analyzed for its thermal performance using two computer codes developed at LLNL. One code calculates the steady state flow conditions along the flow path, while the other calculates the transient conditions in the flow. We have used these codes to analyze the superconductor performance during the burn phase of the ITER plasma. The results of these analyses give insight to the choice of flow rate on superconductor performance. 4 refs., 5 figs

Creep rupture properties under varying load/temperature conditions on a nickel-base heat-resistant alloy strengthened by boron addition

International Nuclear Information System (INIS)

Tsuji, Hirokazu; Tanabe, Tatsuhiko; Nakajima, Hajime

1994-01-01

A series of constant load and temperature creep rupture tests and varying load and temperature creep rupture tests was carried out on Hastelloy XR whose boron content level is 60 mass ppm at 900 and 1000 C in order to examine the behavior of the alloy under varying load and temperature conditions. The life fraction rule completely fails in the prediction of the creep rupture life under varying load and temperature conditions though the rule shows good applicability for Hastelloy XR whose boron content level is below 10 mass ppm. The modified life fraction rule has been proposed based on the dependence of the creep rupture strength on the boron content level of the alloy. The modified rule successfully predicts the creep rupture life under the test conditions from 1000 to 900 C. The trend observed in the tests from 900 to 1000 C can be qualitatively explained by the mechanism that the oxide film which is formed during the prior exposure to 900 C plays the role of the protective barrier against the boron dissipation into the environment. (orig.)

Varying hydric conditions during incubation influence egg water exchange and hatchling phenotype in the red-eared slider turtle.

Science.gov (United States)

Delmas, Virginie; Bonnet, Xavier; Girondot, Marc; Prévot-Julliard, Anne-Caroline

2008-01-01

Environmental conditions within the nest, notably temperature and moisture of substrate, exert a powerful influence during embryogenesis in oviparous reptiles. The influence of fluctuating nest temperatures has been experimentally examined in different reptile species; however, similar experiments using moisture as the key variable are lacking. In this article, we examine the effect of various substrate moisture regimes during incubation on different traits (egg mass, incubation length, and hatchling mass) in a chelonian species with flexible-shelled eggs, the red-eared slider turtle (Trachemys scripta elegans). Our results show that the rate of water uptake by the eggs was higher in wet than in dry substrate and varied across development. More important, during the first third of development, the egg mass changes were relatively independent of the soil moisture level; they became very sensitive to moisture levels during the other two-thirds. Moreover, hydric conditions exerted a strong influence on the eggs' long-term sensitivity to the moisture of the substrate. Even short-term episodes of high or low levels of moisture modified permanently their water sensitivity, notably through modification of eggshell shape and volume, and in turn entailed significant effects on hatchling mass (and hence offspring quality). Such complex influences of fluctuating moisture levels at various incubation stages on hatchling phenotype better reflect the natural situation, compared to experiments based on stable, albeit different, moisture levels.

Wetting boundary condition for the color-gradient lattice Boltzmann method: Validation with analytical and experimental data

Science.gov (United States)

Akai, Takashi; Bijeljic, Branko; Blunt, Martin J.

2018-06-01

In the color gradient lattice Boltzmann model (CG-LBM), a fictitious-density wetting boundary condition has been widely used because of its ease of implementation. However, as we show, this may lead to inaccurate results in some cases. In this paper, a new scheme for the wetting boundary condition is proposed which can handle complicated 3D geometries. The validity of our method for static problems is demonstrated by comparing the simulated results to analytical solutions in 2D and 3D geometries with curved boundaries. Then, capillary rise simulations are performed to study dynamic problems where the three-phase contact line moves. The results are compared to experimental results in the literature (Heshmati and Piri, 2014). If a constant contact angle is assumed, the simulations agree with the analytical solution based on the Lucas-Washburn equation. However, to match the experiments, we need to implement a dynamic contact angle that varies with the flow rate.

Detection and classification of alarm threshold violations in condition monitoring systems working in highly varying operational conditions

Science.gov (United States)

Strączkiewicz, M.; Barszcz, T.; Jabłoński, A.

2015-07-01

All commonly used condition monitoring systems (CMS) enable defining alarm thresholds that enhance efficient surveillance and maintenance of dynamic state of machinery. The thresholds are imposed on the measured values such as vibration-based indicators, temperature, pressure, etc. For complex machinery such as wind turbine (WT) the total number of thresholds might be counted in hundreds multiplied by the number of operational states. All the parameters vary not only due to possible machinery malfunctions, but also due to changes in operating conditions and these changes are typically much stronger than the former ones. Very often, such a behavior may lead to hundreds of false alarms. Therefore, authors propose a novel approach based on parameterized description of the threshold violation. For this purpose the novelty and severity factors are introduced. The first parameter refers to the time of violation occurrence while the second one describes the impact of the indicator-increase to the entire machine. Such approach increases reliability of the CMS by providing the operator with the most useful information of the system events. The idea of the procedure is presented on a simulated data similar to those from a wind turbine.

Detection and classification of alarm threshold violations in condition monitoring systems working in highly varying operational conditions

International Nuclear Information System (INIS)

Strączkiewicz, M; Barszcz, T; Jabłoński, A

2015-01-01

All commonly used condition monitoring systems (CMS) enable defining alarm thresholds that enhance efficient surveillance and maintenance of dynamic state of machinery. The thresholds are imposed on the measured values such as vibration-based indicators, temperature, pressure, etc. For complex machinery such as wind turbine (WT) the total number of thresholds might be counted in hundreds multiplied by the number of operational states. All the parameters vary not only due to possible machinery malfunctions, but also due to changes in operating conditions and these changes are typically much stronger than the former ones. Very often, such a behavior may lead to hundreds of false alarms. Therefore, authors propose a novel approach based on parameterized description of the threshold violation. For this purpose the novelty and severity factors are introduced. The first parameter refers to the time of violation occurrence while the second one describes the impact of the indicator-increase to the entire machine. Such approach increases reliability of the CMS by providing the operator with the most useful information of the system events. The idea of the procedure is presented on a simulated data similar to those from a wind turbine. (paper)

Differences in displayed pump flow compared to measured flow under varying conditions during simulated cardiopulmonary bypass.

LENUS (Irish Health Repository)

Hargrove, M

2008-07-01

Errors in blood flow delivery due to shunting have been reported to reduce flow by, potentially, up to 40-83% during cardiopulmonary bypass. The standard roller-pump measures revolutions per minute and a calibration factor for different tubing sizes calculates and displays flow accordingly. We compared displayed roller-pump flow with ultrasonically measured flow to ascertain if measured flow correlated with the heart-lung pump flow reading. Comparison of flows was measured under varying conditions of pump run duration, temperature, viscosity, varying arterial\\/venous loops, occlusiveness, outlet pressure, use of silicone or polyvinyl chloride (PVC) in the roller race, different tubing diameters, and use of a venous vacuum-drainage device.

Creep rupture properties under varying load/temperature conditions on a nickel-base heat-resistant alloy strengthened by boron addition

International Nuclear Information System (INIS)

Tsuji, Hirokazu; Nakajima, Hajime; Tanabe, Tatsuhiko.

1993-09-01

A series of constant load and temperature creep rupture tests and varying load and temperature creep rupture tests was carried out on Hastelloy XR whose boron content level is 60 mass ppm at 900 and 1000degC in order to examine the behavior of the alloy under varying load and temperature conditions. The life fraction rule completely fails in the prediction of the creep rupture life under varying load and temperature conditions though the rule shows good applicability for Hastelloy XR whose boron content level is below 10 mass ppm. The modified life fraction rule has been proposed based on the dependence of the creep rupture strength on the born content level of the alloy. The modified rule successfully predicts the creep rupture life under the test conditions from 1000degC to 900degC. The trend observed in the tests from 900degC to 1000degC can be qualitatively explained by the mechanism that the oxide film which is formed during the prior exposure to 900degC plays the role of the protective barrier against the boron dissipation into the environment. (author)

Immobilization of uranium in the presence of Fe0(s): Model development and simulation of contrasting experimental conditions

International Nuclear Information System (INIS)

Wang Yong; Salvage, Karen

2005-01-01

A geochemical model is developed for the immobilization of U in the presence of metallic Fe. Zero-valent iron (ZVI) serves as a reducing agent inducing the reductive-precipitation of U, and ZVI corrosion products can serve as absorbing agents for U. The numerical model developed allows the complex interactions of U in solution in differing concentrations to be examined, under variable pH and redox conditions, with or without carbonate, in the presence of ZVI of different size and surface area. It incorporates Fe corrosion, Fe(II) and Fe(III) corrosion product formation, reductive-precipitation of U from the soluble U(VI) valence to the poorly soluble U(IV) valence, adsorption/de-sorption of U onto the Fe oxide corrosion products, and aqueous speciation. The processes of Fe corrosion and reductive precipitation of U are simulated as non-equilibrium, an improvement over other geochemical models. The reductive-precipitation process may use either ZVI or Fe(II) as the reducing agent. The model is calibrated using 3 separate sets of experimental data from published literature that cover a wide range of redox conditions. Sensitivity of the model predictions to variations in input parameters is examined. The simulation results show that the different published experimental results can be explained by different solution chemistries in the studies, specifically O 2 and CO 2 availability and pH, and the amount and surface area of the metallic Fe. With this numerical model the behavior of U in ZVI containing systems over a range of conditions realistic for groundwater can be investigated. By synthesizing observations across several experimental studies, it will lead to a broader understanding of the processes controlling U immobilization under varied geochemical conditions

Spacetime-varying couplings and Lorentz violation

International Nuclear Information System (INIS)

Kostelecky, V. Alan; Lehnert, Ralf; Perry, Malcolm J.

2003-01-01

Spacetime-varying coupling constants can be associated with violations of local Lorentz invariance and CPT symmetry. An analytical supergravity cosmology with a time-varying fine-structure constant provides an explicit example. Estimates are made for some experimental constraints

Analysis of polymer/oxide interfaces under ambient conditions - An experimental perspective

Science.gov (United States)

González-Orive, A.; Giner, I.; de los Arcos, T.; Keller, A.; Grundmeier, G.

2018-06-01

In many different hybrid materials and materials composites polymers adhere to bulk oxides or oxide covered metal. The formed polymer/oxide interfaces are of crucial importance for the functionality and durability of such complex materials. Especially, under humid and corrosive conditions such interfaces tend to degrade due to permeability of polymers for water, the high adsorption energy of water on oxide surfaces and even corrosion processes of the metal. Different experimental studies considered such interfaces ranging from spectroscopy to electrochemical analysis. However, it is still a challenge to understand the complex interaction especially under non-ideal ambient conditions. The perspective article presents an overview on the existing experimental approaches and considers most recent experimental developments with regard to their potential applications in the area of polymer/oxide interfaces in the future.

Experimental characterization of gasoline sprays under highly evaporating conditions

Science.gov (United States)

Khan, Muhammad Mahabat; Sheikh, Nadeem Ahmed; Khalid, Azfar; Lughmani, Waqas Akbar

2018-05-01

An experimental investigation of multistream gasoline sprays under highly evaporating conditions is carried out in this paper. Temperature increase of fuel and low engine pressure could lead to flash boiling. The spray shape is normally modified significantly under flash boiling conditions. The spray plumes expansion along with reduction in the axial momentum causes the jets to merge and creates a low-pressure area below the injector's nozzle. These effects initiate the collapse of spray cone and lead to the formation of a single jet plume or a big cluster like structure. The collapsing sprays reduces exposed surface and therefore they last longer and subsequently penetrate more. Spray plume momentum increase, jet plume reduction and spray target widening could delay or prevent the closure condition and limit the penetration (delayed formation of the cluster promotes evaporation). These spray characteristics are investigated experimentally using shadowgraphy, for five and six hole injectors, under various boundary conditions. Six hole injectors produce more collapsing sprays in comparison to five hole injector due to enhanced jet to jet interactions. The spray collapse tendency reduces with increase in injection pressure due high axial momentum of spray plumes. The spray evaporation rates of five hole injector are observed to be higher than six hole injectors. Larger spray cone angles of the six hole injectors promote less penetrating and less collapsing sprays.

Comparison of creep behavior under varying load/temperature conditions between Hastelloy XR alloys with different boron content levels

International Nuclear Information System (INIS)

Tsuji, Hirokazu; Nakajima, Hajime; Shindo, Masami; Tanabe, Tatsuhiko; Nakasone, Yuji.

1996-01-01

In the design of the high-temperature components, it is often required to predict the creep rupture life under the conditions in which the stress and/or temperature may vary by using the data obtained with the constant load and temperature creep rupture tests. Some conventional creep damage rules have been proposed to meet the above-mentioned requirement. Currently only limited data are available on the behavior of Hastelloy XR, which is a developed alloy as the structural material for high-temperature components of the High-Temperature Engineering Test Reactor (HTTR), under varying stress and/or temperature creep conditions. Hence a series of constant load and temperature creep rupture tests as well as varying load and temperature creep rupture tests was carried out on two kinds of Hastelloy XR alloys whose boron content levels are different, i.e., below 10 and 60 mass ppm. The life fraction rule completely fails in the prediction of the creep rupture life of Hastelloy XR with 60 mass ppm boron under varying load and temperature conditions though the rule shows good applicability for Hastelloy XR with below 10 mass ppm boron. The change of boron content level of the material during the tests is the most probable source of impairing the applicability of the life fraction rule to Hastelloy XR whose boron content level is 60 mass ppm. The modified life fraction rule has been proposed based on the dependence of the creep rupture strength on the boron content level of the alloy. The modified rule successfully predicts the creep rupture life under the two stage creep test conditions from 1000 to 900degC. The trend observed in the two stage creep tests from 900 to 1000degC can be qualitatively explained by the mechanism that the oxide film which is formed during the prior exposure to 900degC plays the role of the protective barrier against the boron dissipation into the environment. (J.P.N.)

Aerodynamic performance of a vibrating piezoelectric fan under varied operational conditions

International Nuclear Information System (INIS)

Stafford, J; Jeffers, N

2014-01-01

This paper experimentally examines the bulk aerodynamic performance of a vibrating fan operating in the first mode of vibration. The influence of operating condition on the local velocity field has also been investigated to understand the flow distribution at the exit region and determine the stalling condition for vibrating fans. Fan motion has been generated and controlled using a piezoelectric ceramic attached to a stainless steel cantilever. The frequency and amplitude at resonance were 109.4 Hz and 12.5 mm, respectively. A test facility has been developed to measure the pressure-flow characteristics of the vibrating fan and simultaneously conduct local velocity field measurements using particle image velocimetry. The results demonstrate the impact of system characteristics on the local velocity field. High momentum regions generated due to the oscillating motion exist with a component direction that is tangent to the blade at maximum displacement. These high velocity zones are significantly affected by increasing impedance while flow reversal is a dominant feature at maximum pressure rise. The findings outlined provide useful information for design of thermal management solutions that may incorporate this air cooling approach.

Analysis of grain filling process to the varied meteorological conditions in winter wheat [Triticum aestivum] cultivars

International Nuclear Information System (INIS)

Inoue, K.; Nakazono, K.; Wakiyama, Y.

2005-01-01

This paper describes effects of varied meteorological conditions on the grain filling periods, stabilities of yield and quality of winter wheat cultivars with different maturity characteristics (cv. Ayahikari, Norin61, Bandowase, and Tsurupikari). In the field experiments, the meteorological treatments were made during the first heading time on 17 April 2001 and the middle heading time on 24 April 2000. Air temperature, global solar radiation and soil moisture were controlled using a rain shelter, cheesecloth and irrigation system. The growth speed and growth period of wheat grains varied among four winter wheat cultivars, depending on meteorological conditions. The growth speed increased within 1 8.4 deg C of mean air temperature over the 30 days after the anthesis. On the other hand, it was found that the growth speed of wheat grains and the maximum number of wheat grains (Ymax) decreased greatly with the 44.4% interception of global solar radiation. Logistic functions were fitted to the relationship between the relative thousand-kernel-weight (Y/Ymax) and the total integrated temperature (sigmaTa) after heading for all treatment conditions. The maximum weight of grains (Ymax) achieved at the harvest time varied somewhat clearly among four winter wheat cultivars and meteorological conditions. Multiple regression analysis showed that the grain yield (Ymax) of four wheat cultivars correlated positively with daily mean solar radiation. It was also found that the cultivar Ayahikari had a highly significant negative correlation between its grain weight and soil moisture. Namely, the grain weight of high soil moisture plot with pF=1.5 was lower by about 9% than that of a control plot with pF=3.5. On the other hand, the grain yield of cultivar Norin61 responded inversely to a wet environment, indicating that its grain weight was higher for high soil moisture and high wet-bulb temperature than for a dry environment. The grain yield of early varieties of Bandowase and

The effect of varying talker identity and listening conditions on gaze behavior during audiovisual speech perception.

Science.gov (United States)

Buchan, Julie N; Paré, Martin; Munhall, Kevin G

2008-11-25

During face-to-face conversation the face provides auditory and visual linguistic information, and also conveys information about the identity of the speaker. This study investigated behavioral strategies involved in gathering visual information while watching talking faces. The effects of varying talker identity and varying the intelligibility of speech (by adding acoustic noise) on gaze behavior were measured with an eyetracker. Varying the intelligibility of the speech by adding noise had a noticeable effect on the location and duration of fixations. When noise was present subjects adopted a vantage point that was more centralized on the face by reducing the frequency of the fixations on the eyes and mouth and lengthening the duration of their gaze fixations on the nose and mouth. Varying talker identity resulted in a more modest change in gaze behavior that was modulated by the intelligibility of the speech. Although subjects generally used similar strategies to extract visual information in both talker variability conditions, when noise was absent there were more fixations on the mouth when viewing a different talker every trial as opposed to the same talker every trial. These findings provide a useful baseline for studies examining gaze behavior during audiovisual speech perception and perception of dynamic faces.

Experimental study of micro-shock tube flow

Energy Technology Data Exchange (ETDEWEB)

Park, Jin Ouk; Kim, Gyu Wan; Rasel, Md. Alim Iftakhar [Dept. of Mechanical Engineering, Andong National University, Andong (Korea, Republic of); Kim, Heuy Dong [Fire Research Center, Korea Institute of Civil Engineering and Building Technology, Hwasung (Korea, Republic of)

2015-03-15

The flow characteristics in micro shock tube are investigated experimentally. Studies were carried out using a stainless steel micro shock tube. Shock and expansion wave was measured using 8 pressure sensors. The initial pressure ratio was varied from 4.3 to 30.5, and the diameter of tube was also changed from 3 mm to 6 mm. Diaphragm conditions were varied using two types of diaphragms. The results obtained show that the shock strength in the tube becomes stronger for an increase in the initial pressure ratio and diameter of tube. For the thinner diaphragm, the highest shock strength was found among varied diaphragm condition. Shock attenuation was highly influenced by the diameter of tube.

Detectors for Linear Colliders: Physics Requirements and Experimental Conditions (1/4)

CERN Multimedia

CERN. Geneva

2010-01-01

How is the anticipated physics program of a future e+e- collider shaping the R&D for new detectors in collider particle physics ? This presentation will review the main physics requirements and experimental conditions comparing to LHC and LEP. In particular, I shall discuss how e+e- experimentation is expected to change moving from LEP-2 up to multi-TeV energies.

Identification of time-varying structural dynamic systems - An artificial intelligence approach

Science.gov (United States)

Glass, B. J.; Hanagud, S.

1992-01-01

An application of the artificial intelligence-derived methodologies of heuristic search and object-oriented programming to the problem of identifying the form of the model and the associated parameters of a time-varying structural dynamic system is presented in this paper. Possible model variations due to changes in boundary conditions or configurations of a structure are organized into a taxonomy of models, and a variant of best-first search is used to identify the model whose simulated response best matches that of the current physical structure. Simulated model responses are verified experimentally. An output-error approach is used in a discontinuous model space, and an equation-error approach is used in the parameter space. The advantages of the AI methods used, compared with conventional programming techniques for implementing knowledge structuring and inheritance, are discussed. Convergence conditions and example problems have been discussed. In the example problem, both the time-varying model and its new parameters have been identified when changes occur.

Effect of storage conditions on the calorific value of municipal solid waste.

Science.gov (United States)

Nzioka, Antony Mutua; Hwang, Hyeon-Uk; Kim, Myung-Gyun; Yan, Cao Zheng; Lee, Chang-Soo; Kim, Young-Ju

2017-08-01

Storage conditions are considered to be an important factor as far as waste material characteristics are concerned. This experimental investigation was conducted using municipal solid waste (MSW) with a high moisture content and varying composition of organic waste. The objective of this study was to understand the effect of storage conditions and temperature on the moisture content and calorific value of the waste. Samples were subjected to two different storage conditions and investigated at specified temperatures. The composition of sample materials investigated was varied for each storage condition and temperature respectively. Gross calorific value was determined experimentally while net calorific value was calculated using empirical formulas proposed by other researchers. Results showed minimal changes in moisture content as well as in gross and net calorific values when the samples were subjected to sealed storage conditions. Moisture content reduced due to the ventilation process and the rate of moisture removal increased with a rise in storage temperature. As expected, rate of moisture removal had a positive effect on gross and net calorific values. Net calorific values also increased at varying rates with a simultaneous decrease in moisture content. Experimental investigation showed the effectiveness of ventilation in improving the combustion characteristics of the waste.

Design of experimental system for supercritical CO2 fracturing under confining pressure conditions

Science.gov (United States)

Wang, H.; Lu, Q.; Li, X.; Yang, B.; Zheng, Y.; Shi, L.; Shi, X.

2018-03-01

Supercritical CO2 has the characteristics of low viscosity, high diffusion and zero surface tension, and it is considered as a new fluid for non-polluting and non-aqueous fracturing which can be used for shale gas development. Fracturing refers to a method of utilizing the high-pressure fluid to generate fractures in the rock formation so as to improve the oil and gas flow conditions and increase the oil and gas production. In this article, a new type of experimental system for supercritical CO2 fracturing under confining pressure conditions is designed, which is based on characteristics of supercritical CO2, shale reservoir and down-hole environment. The experimental system consists of three sub-systems, including supercritical CO2 generation system, supercritical CO2 fracturing system and data analysis system. It can be used to simulate supercritical CO2 fracturing under geo-stress conditions, thus to study the rock initiation pressure, the formation of the rock fractures, fractured surface morphology and so on. The experimental system has successfully carried out a series of supercritical CO2 fracturing experiments. The experimental results confirm the feasibility of the experimental system and the high efficiency of supercritical CO2 in fracturing tight rocks.

Effect of Varying Hemodynamic and Vascular Conditions on Fractional Flow Reserve: An In Vitro Study.

Science.gov (United States)

Kolli, Kranthi K; Min, James K; Ha, Seongmin; Soohoo, Hilary; Xiong, Guanglei

2016-06-30

The aim of this study was to investigate the impact of varying hemodynamic conditions on fractional flow reserve (ratio of pressure distal [Pd] and proximal [Pa] to stenosis under hyperemia) in an in vitro setting. Failure to achieve maximal hyperemia and the choice of hyperemic agents may have differential effects on coronary hemodynamics and, consequently, on the determination of fractional flow reserve. An in vitro flow system was developed to experimentally model the physiological coronary circulation as flow-dependent stenosis resistance in series with variable downstream resistance. Five idealized models with 30% to 70% diameter stenosis severity were fabricated using VeroClear rigid material in an Objet260 Connex printer. Mean aortic pressure was maintained at 7 levels (60-140 mm Hg) from hypotension to hypertension using a needle valve that mimicked adjustable microcirculatory resistance. A range of physiological flow rates was applied by a steady flow pump and titrated by a flow sensor. The pressure drop and the pressure ratio (Pd/Pa) were assessed for the 7 levels of aortic pressure and differing flow rates. The in vitro experimental data were coupled with pressure-flow relationships from clinical data for populations with and without myocardial infarction, respectively, to evaluate fractional flow reserve. The curve for pressure ratio and flow rate demonstrated a quadratic relationship with a decreasing slope. The absolute decrease in fractional flow reserve in the group without myocardial infarction (with myocardial infarction) was on the order of 0.03 (0.02), 0.05 (0.02), 0.07 (0.05), 0.17 (0.13) and 0.20 (0.24), respectively, for 30%, 40%, 50%, 60%, and 70% diameter stenosis, for an increase in aortic pressure from 60 to 140 mm Hg. The fractional flow reserve value, an index of physiological stenosis significance, was observed to decrease with increasing aortic pressure for a given stenosis in this idealized in vitro experiment for vascular

Experimental investigations of two-phase mixture level swell and axial void fraction distribution under high pressure, low heat flux conditions in rod bundle geometry

International Nuclear Information System (INIS)

Anklam, T.M.; White, M.D.

1981-01-01

Experimental data is reported from a series of quasi-steady-state two-phase mixture level swell and void fraction distribution tests. Testing was performed at ORNL in the Thermal Hydraulic Test Facility - a large electrically heated test loop configured to produce conditions similar to those expected in a small break loss of coolant accident. Pressure was varied from 2.7 to 8.2 MPa and linear power ranged from 0.33 to 1.95 kW/m. Mixture swell was observed to vary linearly with the total volumetric vapor generation rate over the power range of primary interest in small break analysis. Void fraction data was fit by a drift-flux model and both the drift-velocity and concentration parameter were observed to decrease with increasing pressure

Nonlinear systems time-varying parameter estimation: Application to induction motors

Energy Technology Data Exchange (ETDEWEB)

Kenne, Godpromesse [Laboratoire d' Automatique et d' Informatique Appliquee (LAIA), Departement de Genie Electrique, IUT FOTSO Victor, Universite de Dschang, B.P. 134 Bandjoun (Cameroon); Ahmed-Ali, Tarek [Ecole Nationale Superieure des Ingenieurs des Etudes et Techniques d' Armement (ENSIETA), 2 Rue Francois Verny, 29806 Brest Cedex 9 (France); Lamnabhi-Lagarrigue, F. [Laboratoire des Signaux et Systemes (L2S), C.N.R.S-SUPELEC, Universite Paris XI, 3 Rue Joliot Curie, 91192 Gif-sur-Yvette (France); Arzande, Amir [Departement Energie, Ecole Superieure d' Electricite-SUPELEC, 3 Rue Joliot Curie, 91192 Gif-sur-Yvette (France)

2008-11-15

In this paper, an algorithm for time-varying parameter estimation for a large class of nonlinear systems is presented. The proof of the convergence of the estimates to their true values is achieved using Lyapunov theories and does not require that the classical persistent excitation condition be satisfied by the input signal. Since the induction motor (IM) is widely used in several industrial sectors, the algorithm developed is potentially useful for adjusting the controller parameters of variable speed drives. The method proposed is simple and easily implementable in real-time. The application of this approach to on-line estimation of the rotor resistance of IM shows a rapidly converging estimate in spite of measurement noise, discretization effects, parameter uncertainties (e.g. inaccuracies on motor inductance values) and modeling inaccuracies. The robustness analysis for this IM application also revealed that the proposed scheme is insensitive to the stator resistance variations within a wide range. The merits of the proposed algorithm in the case of on-line time-varying rotor resistance estimation are demonstrated via experimental results in various operating conditions of the induction motor. The experimental results obtained demonstrate that the application of the proposed algorithm to update on-line the parameters of an adaptive controller (e.g. IM and synchronous machines adaptive control) can improve the efficiency of the industrial process. The other interesting features of the proposed method include fault detection/estimation and adaptive control of IM and synchronous machines. (author)

Collective action in culturally similar and dissimilar groups: An axperiment on parochialism, conditional cooperation, and their linkages

NARCIS (Netherlands)

Koopmans, R.; Rebers, S.

2009-01-01

This study examines the effects of ingroup favoritism and outgroup hostility ("parochialism"), as well as of conditionally cooperative strategies, in explaining contributions to experimental public goods games. The experimental conditions vary group composition along two culturally inheritable

Experimental and numerical study of an evaporatively-cooled condenser of air-conditioning systems

International Nuclear Information System (INIS)

Islam, M.R.; Jahangeer, K.A.; Chua, K.J.

2015-01-01

The performance of an air-conditioning unit with evaporately-cooled condenser coil is studied experimentally and numerically. An experimental setup is fabricated by retrofitting a commercially available air-conditioning unit and installing comprehensive measuring sensors and controllers. Experimental result shows that the COP (Coefficient of Performance) of the evaporately-cooled air-conditioning unit increases by about 28% compared to the conventional air cooled air-conditioning unit. To analyze the heat and mass transfer processes involved in the evaporately-cooled condenser, a detailed theoretical model has been developed based on the fluid flow characteristics of the falling film and the thermodynamic aspect of the evaporation process. Simulated results agree well with experimental data. The numerical model provides new insights into the intrinsic links between operating variables and heat transfer characteristics of water film in evaluating the performance of evaporatively-cooled condenser system. Two heat transfer coefficients, namely, wall to bulk and bulk to interface are introduced and computed from the simulation results under different operating conditions. Finally, the overall heat transfer coefficient for the water film is computed and presented as a function of dimensionless variables which can conveniently be employed by engineers to design and analyze high performance evaporatively-cooled heat exchangers. - Highlights: • Performance of evaporatively-cooled condenser is investigated. • Local convective heat transfer coefficients of water film are determined. • Thermal resistance of water film is negligible. • Heat transfer with evaporated vapor plays significant role on performance. • Better condenser performance translates to an improvement in COP

Experiments and numerical modeling of fast flowing liquid metal thin films under spatially varying magnetic field conditions

Science.gov (United States)

Narula, Manmeet Singh

Innovative concepts using fast flowing thin films of liquid metals (like lithium) have been proposed for the protection of the divertor surface in magnetic fusion devices. However, concerns exist about the possibility of establishing the required flow of liquid metal thin films because of the presence of strong magnetic fields which can cause flow disrupting MHD effects. A plan is underway to design liquid lithium based divertor protection concepts for NSTX, a small spherical torus experiment at Princeton. Of these, a promising concept is the use of modularized fast flowing liquid lithium film zones, as the divertor (called the NSTX liquid surface module concept or NSTX LSM). The dynamic response of the liquid metal film flow in a spatially varying magnetic field configuration is still unknown and it is suspected that some unpredicted effects might be lurking. The primary goal of the research work being reported in this dissertation is to provide qualitative and quantitative information on the liquid metal film flow dynamics under spatially varying magnetic field conditions, typical of the divertor region of a magnetic fusion device. The liquid metal film flow dynamics have been studied through a synergic experimental and numerical modeling effort. The Magneto Thermofluid Omnibus Research (MTOR) facility at UCLA has been used to design several experiments to study the MHD interaction of liquid gallium films under a scaled NSTX outboard divertor magnetic field environment. A 3D multi-material, free surface MHD modeling capability is under development in collaboration with HyPerComp Inc., an SBIR vendor. This numerical code called HIMAG provides a unique capability to model the equations of incompressible MHD with a free surface. Some parts of this modeling capability have been developed in this research work, in the form of subroutines for HIMAG. Extensive code debugging and benchmarking exercise has also been carried out. Finally, HIMAG has been used to study the

Experimental Setup for Determining Ammonia-Salt Adsorption and Desorption Behavior Under Typical Heat Pump Conditions. Experimental Results

Energy Technology Data Exchange (ETDEWEB)

Van der Pal, M.; De Boer, R.; Veldhuis, J.B.J. [ECN Biomass and Energy Efficiency, Petten (Netherlands)

2013-09-15

For the aim of obtaining a better understanding of the performance of a salt-ammonia sorption reactor/heat exchanger a new test-rig was developed. This test-rig enables the measurement of the performance in adsorption and desorption mode of different sorption reactor designs. It measures the speed of uptake and release of ammonia gas of various salt-ammonia reactions under well-controlled and well-monitored process conditions, similar to the heat pump conditions. The test-rig measures the ammonia uptake and release under controlled pressure and temperature conditions. Temperatures of the salt reactor can be varied from ambient temperature up to 200{sup o}C and the ammonia pressure can be varied between 0.02 to 2 MPa. These conditions can be set independently and repeated at regular time-intervals. Besides NH3-mass-flow meters, pressure and temperature sensors, the setup also contains an endoscope to observe any macroscopic structural changes in the material during uptake and release of ammonia. Measurements so far have shown a liquid phase of LiCl.3NH3 at pressures of 0.5 MPa and temperatures exceeding 90{sup o}C. Voilent foaming is observed at 120{sup o}C resulting in salt losses. A correlation was determined between the reaction rate of MgCl{sub 2}(2-6)NH3 and the relative pressure gradient yielding a reaction time of about 1500 seconds for a relative pressure difference of 1. Multiple sorption cycles of the CaCl{sub 2}(2-4)NH3 reaction, showed a reduced activity from 85% of the theoretical maximum sorbed mass at the first sorption cycle, to 15% after 300+ cycles.

A discrete time-varying internal model-based approach for high precision tracking of a multi-axis servo gantry.

Science.gov (United States)

Zhang, Zhen; Yan, Peng; Jiang, Huan; Ye, Peiqing

2014-09-01

In this paper, we consider the discrete time-varying internal model-based control design for high precision tracking of complicated reference trajectories generated by time-varying systems. Based on a novel parallel time-varying internal model structure, asymptotic tracking conditions for the design of internal model units are developed, and a low order robust time-varying stabilizer is further synthesized. In a discrete time setting, the high precision tracking control architecture is deployed on a Voice Coil Motor (VCM) actuated servo gantry system, where numerical simulations and real time experimental results are provided, achieving the tracking errors around 3.5‰ for frequency-varying signals. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Risky behavior and its effect on survival: snowshoe hare behavior under varying moonlight conditions

Science.gov (United States)

Gigliotti, Laura C.; Diefenbach, Duane R.

2018-01-01

Predation and predation risk can exert strong influences on the behavior of prey species. However, risk avoidance behaviors may vary among populations of the same species. We studied a population of snowshoe hares (Lepus americanus) near the southern edge of their range, in Pennsylvania. This population occupies different habitat types, experiences different environmental conditions, and are exposed to different predator species and densities than northern hare populations; therefore, they might exhibit differences in risk avoidance behaviors. We analyzed hare survival, movement rates, and habitat use under different levels of predation risk, as indexed by moonlight. Similar to previous work, we found snowshoe hare survival decreased with increased moon illumination during the winter, but we found differences in behavioral responses to increased predation risk. We found that snowshoe hares did not reduce movement rates during high‐risk nights, but instead found that hares selected areas with denser canopy cover, compared to low‐risk nights. We suggest that behavioral plasticity in response to predation risk allows populations of the same species to respond to localized conditions.

Experimental Study on Effect of Operating Conditions on Thermoelectric Power Generation

DEFF Research Database (Denmark)

Mahmoudi Nezhad, Sajjad; Rezaniakolaei, Alireza; Rosendahl, Lasse Aistrup

2017-01-01

Effect of boundary conditions of thermal reservoirs on power generation of thermoelectric modules (TEMs) is examined experimentally. To realize the characteristics of the power generation by the TEMs, the system performance is studied over various volumetric flow rates and flow temperatures...

Effects of varying environmental conditions on emissivity spectra of bulk lunar soils: Application to Diviner thermal infrared observations of the Moon

Science.gov (United States)

Donaldson Hanna, K. L.; Greenhagen, B. T.; Patterson, W. R.; Pieters, C. M.; Mustard, J. F.; Bowles, N. E.; Paige, D. A.; Glotch, T. D.; Thompson, C.

2017-02-01

Currently, few thermal infrared measurements exist of fine particulate (samples (e.g. minerals, mineral mixtures, rocks, meteorites, and lunar soils) measured under simulated lunar conditions. Such measurements are fundamental for interpreting thermal infrared (TIR) observations by the Diviner Lunar Radiometer Experiment (Diviner) onboard NASA's Lunar Reconnaissance Orbiter as well as future TIR observations of the Moon and other airless bodies. In this work, we present thermal infrared emissivity measurements of a suite of well-characterized Apollo lunar soils and a fine particulate (sample as we systematically vary parameters that control the near-surface environment in our vacuum chamber (atmospheric pressure, incident solar-like radiation, and sample cup temperature). The atmospheric pressure is varied between ambient (1000 mbar) and vacuum (radiation is varied between 52 and 146 mW/cm2, and the sample cup temperature is varied between 325 and 405 K. Spectral changes are characterized as each parameter is varied, which highlight the sensitivity of thermal infrared emissivity spectra to the atmospheric pressure and the incident solar-like radiation. Finally spectral measurements of Apollo 15 and 16 bulk lunar soils are compared with Diviner thermal infrared observations of the Apollo 15 and 16 sampling sites. This comparison allows us to constrain the temperature and pressure conditions that best simulate the near-surface environment of the Moon for future laboratory measurements and to better interpret lunar surface compositions as observed by Diviner.

Mapping and simulating systematics due to spatially varying observing conditions in DES science verification data

International Nuclear Information System (INIS)

Leistedt, B.; Peiris, H. V.; Elsner, F.; Benoit-Lévy, A.; Amara, A.

2016-01-01

Spatially varying depth and the characteristics of observing conditions, such as seeing, airmass, or sky background, are major sources of systematic uncertainties in modern galaxy survey analyses, particularly in deep multi-epoch surveys. We present a framework to extract and project these sources of systematics onto the sky, and apply it to the Dark Energy Survey (DES) to map the observing conditions of the Science Verification (SV) data. The resulting distributions and maps of sources of systematics are used in several analyses of DES–SV to perform detailed null tests with the data, and also to incorporate systematics in survey simulations. We illustrate the complementary nature of these two approaches by comparing the SV data with BCC-UFig, a synthetic sky catalog generated by forward-modeling of the DES–SV images. We analyze the BCC-UFig simulation to construct galaxy samples mimicking those used in SV galaxy clustering studies. We show that the spatially varying survey depth imprinted in the observed galaxy densities and the redshift distributions of the SV data are successfully reproduced by the simulation and are well-captured by the maps of observing conditions. The combined use of the maps, the SV data, and the BCC-UFig simulation allows us to quantify the impact of spatial systematics on N(z), the redshift distributions inferred using photometric redshifts. We conclude that spatial systematics in the SV data are mainly due to seeing fluctuations and are under control in current clustering and weak-lensing analyses. However, they will need to be carefully characterized in upcoming phases of DES in order to avoid biasing the inferred cosmological results. Finally, the framework presented here is relevant to all multi-epoch surveys and will be essential for exploiting future surveys such as the Large Synoptic Survey Telescope, which will require detailed null tests and realistic end-to-end image simulations to correctly interpret the deep, high

Experimental Aspects in the Vibration-Based Condition Monitoring of Large Hydrogenerators

Directory of Open Access Journals (Sweden)

Geraldo Carvalho Brito Junior

2017-01-01

Full Text Available Based on experimental observations on a set of twenty 700 MW hydrogenerators, compiled from several technical reports issued over the last three decades and collected from the reprocessing of the vibration signals recorded during the last commissioning tests, this paper shows that the accurate determination of the journal bearings operating conditions may be a difficult task. It shows that the outsize bearing brackets of large hydrogenerators are subject to substantial dimensional changes caused by external agents, like the generator electromagnetic field and the bearing cooling water temperature. It also shows that the shaft eccentricity of a journal bearing of a healthy large hydrogenerator, operating in steady-state condition, may experience unpredictable, sudden, and significant changes without apparent reasons. Some of these phenomena are reproduced in ordinary commissioning tests or may be noticed even during normal operation, while others are rarely observed or are only detected through special tests. These phenomena modify journal bearings stiffness and damping, changing the hydrogenerator dynamics, creating discrepancies between theoretical predictions and experimental measurements, and making damage detection and diagnostics difficult. Therefore, these phenomena must be analyzed and considered in the application of vibration-based condition monitoring to these rotating machines.

Factorial experimental design intended for the optimization of the alumina purification conditions

Science.gov (United States)

Brahmi, Mounaouer; Ba, Mohamedou; Hidri, Yassine; Hassen, Abdennaceur

2018-04-01

The objective of this study was to determine the optimal conditions by using the experimental design methodology for the removal of some impurities associated with the alumina. So, three alumina qualities of different origins were investigated under the same conditions. The application of full-factorial designs on the samples of different qualities of alumina has followed the removal rates of the sodium oxide. However, a factorial experimental design was developed to describe the elimination of sodium oxide associated with the alumina. The experimental results showed that chemical analyze followed by XRF prior treatment of the samples, provided a primary idea concerning these prevailing impurities. Therefore, it appeared that the sodium oxide constituted the largest amount among all impurities. After the application of experimental design, analysis of the effectors different factors and their interactions showed that to have a better result, we should reduce the alumina quantity investigated and by against increase the stirring time for the first two samples, whereas, it was necessary to increase the alumina quantity in the case of the third sample. To expand and improve this research, we should take into account all existing impurities, since we found during this investigation that the levels of partial impurities increased after the treatment.

Modelling of the diffusion of pollutants in the atmosphere under varying conditions in large cultivated regions

International Nuclear Information System (INIS)

Wueneke, C.D.; Schultz, H.

1975-01-01

The most important routines of a numerical code based on the particle-in-cell-method for calculating the transport and the turbulent dispersion of inert and radio-active pollutants in the atmosphere have been programmed and have been tested successfully on the CDC computer CYBER 73/76 of the Regional Computer Centre for Niedersachsen in Hanover. Compared to the Gaussian plume model such a numerical code based on the particle-in-cell-method offers several advantages for the computation of the diffusion under varying conditions in large cultivated regions. (orig.) [de

Diesel soot oxidation under controlled conditions

OpenAIRE

Song, Haiwen

2003-01-01

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University, 11/12/2003. In order to improve understanding of diesel soot oxidation, an experimental rig was designed and set up, in which the soot oxidation conditions, such as temperature, oxygen partial pressure, and CO2 partial pressure, could be varied independently of each other. The oxidizing gas flow in the oxidizer was under laminar condition. This test rig comprised a naturally-aspirated single ...

Vibration Analysis of a Tire in Ground Contact under Varied Conditions

Directory of Open Access Journals (Sweden)

Karakus Murat

2017-03-01

Full Text Available The effect of three different factors, which are inflation pressure, vertical load and coefficient of friction on the natural frequencies of a tire (175/70 R13 has been studied. A three dimensional tire model is constructed, using four different material properties and parts in the tire. Mechanical properties of the composite parts are evaluated. After investigating the free vibration, contact analysis is carried out. A concrete block and the tire are modelled together, using three different coefficients of friction. Experiments are run under certain conditions to check the accuracy of the numerical model. The natural frequencies are measured to describe free vibration and vibration of the tire contacted by ground, using a damping monitoring method. It is seen, that experimental and numerical results are in good agreement. On the other hand, investigating the impact of three different factors together is quite difficult on the natural frequencies. When some of these factors are assumed to be constant and the variables are taken one by one, it is easier to assess the effects.

Establishment of a head injury by club model in rabbits and experimental conditions

International Nuclear Information System (INIS)

Cao Yunxing; Xi Huanjiu; Zhang Jing; Li Hongwei; Yin Zhiyong; Zhao Hui

2013-01-01

Objective: To establish an animal model to replicate the injury by club in forensic medicine. Methods: Twenty-four New Zealand white rabbits were divided into control group (n=4), minor injury group (n=10), and severe injury group (n=10). Based on the BIM-Ⅱ Horizontal Bio-impact Machine, a self-designed iron bar was used to produce head injury by club. Six hours after injury, all the rabbits were subjected to a CT examination and dissected to observe the injury morphology and undergo routine pathological examination. Four control, six minor and severe rabbits were given moisture content examination. Results: Varying degrees of positive signs of the nervous system were observed in all the injured rabbits within 6 hours. The mortality rate was 1/10 in the minor injury group and 6/10 in the severe injury group. The morphological changes consisted of different levels of scalp hematoma, skull fracture, epidural hematoma, subdural hematoma, subarachnoid hemorrhage and brain injury. The difference in moisture content between the three groups was of statistical significance. Conclusion: Under the rigidly-controlled experimental condition, this animal model produces good reproducibility and stable results. Meanwhile, it can simulate the morphology of injury by club and be used to study the mechanism of injury by club in forensic medicine. (authors)

Experimental observation of dynamic ductile damage development under various triaxiality conditions - description of the principle

Directory of Open Access Journals (Sweden)

Pillon L.

2012-08-01

Full Text Available The Gurson model has been extended by Perrin to describe damage evolution in ductile viscoplastic materials. The so-called Gurson-Perrin model allows representing damage development with respect to strain-rate conditions. In order to fill a lack in current experimental procedures, we propose an experimental project able to test and validate the Gurson-Perrin model under various dynamic conditions and for different stress triaxiality levels.

Experimental measurements of the solubility of technetium under near-field conditions

International Nuclear Information System (INIS)

Pilkington, N.J.; Wilkins, J.D.

1988-05-01

The solubility of technetium in contact with hydrated technetium dioxide under near-field conditions has been measured experimentally. The values obtained were changed little by a change in pH or in the filtration method used. The presence of organic degradation products increased slightly the solution concentration of technetium. (author)

Experimental study of a novel capacity control algorithm for a multi-evaporator air conditioning system

International Nuclear Information System (INIS)

Xu Xiangguo; Pan Yan; Deng Shiming; Xia Liang; Chan Mingyin

2013-01-01

The use of a multi-evaporator air conditioning (MEAC) system is advantageous in terms of installation convenience, high design flexibility, being easy to maintain and commission, better indoor thermal comfort control and higher energy efficiency. While MEAC units worth billions of dollars are sold worldwide, the detailed accounts on compressor capacity control and refrigeration flow distribution amongst evaporators remain unavailable in public domain, mainly due to commercial confidentiality. Limited control algorithms for MEAC systems have been developed based on system simulation, and no experimental-based capacity controller developments and their controllability tests may be identified in open literature. In the study reported in this paper, a novel capacity control algorithm, which imitated On–Off control of a single evaporator air conditioning (A/C) system in each indoor unit of a MEAC system by using variable speed compressor and electronic expansion valves (EEVs), was developed. Controllability tests under various settings for experimentally validating the novel capacity control algorithm were carried out and the control algorithm was further improved based on the experimental results. - Highlights: ► A capacity control algorithm for a multi-evaporator air conditioning system was developed. ► Experimental controllability tests under various settings were carried out. ► The control algorithm was further improved based on the experimental results.

Postnatal development of the hippocampal dentate gyrus under normal and experimental conditions

International Nuclear Information System (INIS)

Altman, J.; Bayer, S.

Studies on postnatal maturation of the dentate gyrus are reviewed. Some topics discussed are: normal development of the dentate gyrus, cytogenesis, morphogenesis, synaptogenesis, gleogenesis, myelogenesis, development of the gyrus under experimental conditions, and effects of x radiation on cytogenesis and morphogenesis

Urban tree species show the same hydraulic response to vapor pressure deficit across varying tree size and environmental conditions.

Directory of Open Access Journals (Sweden)

Lixin Chen

Full Text Available The functional convergence of tree transpiration has rarely been tested for tree species growing under urban conditions even though it is of significance to elucidate the relationship between functional convergence and species differences of urban trees for establishing sustainable urban forests in the context of forest water relations.We measured sap flux of four urban tree species including Cedrus deodara, Zelkova schneideriana, Euonymus bungeanus and Metasequoia glyptostroboides in an urban park by using thermal dissipation probes (TDP. The concurrent microclimate conditions and soil moisture content were also measured. Our objectives were to examine 1 the influence of tree species and size on transpiration, and 2 the hydraulic control of urban trees under different environmental conditions over the transpiration in response to VPD as represented by canopy conductance. The results showed that the functional convergence between tree diameter at breast height (DBH and tree canopy transpiration amount (E(c was not reliable to predict stand transpiration and there were species differences within same DBH class. Species differed in transpiration patterns to seasonal weather progression and soil water stress as a result of varied sensitivity to water availability. Species differences were also found in their potential maximum transpiration rate and reaction to light. However, a same theoretical hydraulic relationship between G(c at VPD = 1 kPa (G(cref and the G(c sensitivity to VPD (-dG(c/dlnVPD across studied species as well as under contrasting soil water and R(s conditions in the urban area.We concluded that urban trees show the same hydraulic regulation over response to VPD across varying tree size and environmental conditions and thus tree transpiration could be predicted with appropriate assessment of G(cref.

Urban tree species show the same hydraulic response to vapor pressure deficit across varying tree size and environmental conditions.

Science.gov (United States)

Chen, Lixin; Zhang, Zhiqiang; Ewers, Brent E

2012-01-01

The functional convergence of tree transpiration has rarely been tested for tree species growing under urban conditions even though it is of significance to elucidate the relationship between functional convergence and species differences of urban trees for establishing sustainable urban forests in the context of forest water relations. We measured sap flux of four urban tree species including Cedrus deodara, Zelkova schneideriana, Euonymus bungeanus and Metasequoia glyptostroboides in an urban park by using thermal dissipation probes (TDP). The concurrent microclimate conditions and soil moisture content were also measured. Our objectives were to examine 1) the influence of tree species and size on transpiration, and 2) the hydraulic control of urban trees under different environmental conditions over the transpiration in response to VPD as represented by canopy conductance. The results showed that the functional convergence between tree diameter at breast height (DBH) and tree canopy transpiration amount (E(c)) was not reliable to predict stand transpiration and there were species differences within same DBH class. Species differed in transpiration patterns to seasonal weather progression and soil water stress as a result of varied sensitivity to water availability. Species differences were also found in their potential maximum transpiration rate and reaction to light. However, a same theoretical hydraulic relationship between G(c) at VPD = 1 kPa (G(cref)) and the G(c) sensitivity to VPD (-dG(c)/dlnVPD) across studied species as well as under contrasting soil water and R(s) conditions in the urban area. We concluded that urban trees show the same hydraulic regulation over response to VPD across varying tree size and environmental conditions and thus tree transpiration could be predicted with appropriate assessment of G(cref).

Experimental and Theoretical Determination of Heavy Oil Viscosity Under Reservoir Conditions; ANNUAL

International Nuclear Information System (INIS)

Gabitto, Jorge; Barrufet, Maria

2002-01-01

The main objective of this research was to propose a simple procedure to predict heavy oil viscosity at reservoir conditions as a function of easily determined physical properties. This procedure will avoid costly experimental testing and reduce uncertainty in designing thermal recovery processes

The influence of spatially and temporally varying oceanographic conditions on meroplanktonic metapopulations

Science.gov (United States)

Botsford, L. W.; Moloney, C. L.; Hastings, A.; Largier, J. L.; Powell, T. M.; Higgins, K.; Quinn, J. F.

We synthesize the results of several modelling studies that address the influence of variability in larval transport and survival on the dynamics of marine metapopulations distributed along a coast. Two important benthic invertebrates in the California Current System (CCS), the Dungeness crab and the red sea urchin, are used as examples of the way in which physical oceanographic conditions can influence stability, synchrony and persistence of meroplanktonic metapopulations. We first explore population dynamics of subpopulations and metapopulations. Even without environmental forcing, isolated local subpopulations with density-dependence can vary on time scales roughly twice the generation time at high adult survival, shifting to annual time scales at low survivals. The high frequency behavior is not seen in models of the Dungeness crab, because of their high adult survival rates. Metapopulations with density-dependent recruitment and deterministic larval dispersal fluctuate in an asynchronous fashion. Along the coast, abundance varies on spatial scales which increase with dispersal distance. Coastwide, synchronous, random environmental variability tends to synchronize these metapopulations. Climate change could cause a long-term increase or decrease in mean larval survival, which in this model leads to greater synchrony or extinction respectively. Spatially managed metapopulations of red sea urchins go extinct when distances between harvest refugia become greater than the scale of larval dispersal. All assessments of population dynamics indicate that metapopulation behavior in general dependes critically on the temporal and spatial nature of larval dispersal, which is largely determined by physical oceanographic conditions. We therfore explore physical influences on larval dispersal patterns. Observed trends in temperature and salinity applied to laboratory-determined responses indicate that natural variability in temperature and salinity can lead to variability in

Genome-wide transcriptome analysis of soybean primary root under varying water-deficit conditions.

Science.gov (United States)

Song, Li; Prince, Silvas; Valliyodan, Babu; Joshi, Trupti; Maldonado dos Santos, Joao V; Wang, Jiaojiao; Lin, Li; Wan, Jinrong; Wang, Yongqin; Xu, Dong; Nguyen, Henry T

2016-01-15

Soybean is a major crop that provides an important source of protein and oil to humans and animals, but its production can be dramatically decreased by the occurrence of drought stress. Soybeans can survive drought stress if there is a robust and deep root system at the early vegetative growth stage. However, little is known about the genome-wide molecular mechanisms contributing to soybean root system architecture. This study was performed to gain knowledge on transcriptome changes and related molecular mechanisms contributing to soybean root development under water limited conditions. The soybean Williams 82 genotype was subjected to very mild stress (VMS), mild stress (MS) and severe stress (SS) conditions, as well as recovery from the severe stress after re-watering (SR). In total, 6,609 genes in the roots showed differential expression patterns in response to different water-deficit stress levels. Genes involved in hormone (Auxin/Ethylene), carbohydrate, and cell wall-related metabolism (XTH/lipid/flavonoids/lignin) pathways were differentially regulated in the soybean root system. Several transcription factors (TFs) regulating root growth and responses under varying water-deficit conditions were identified and the expression patterns of six TFs were found to be common across the stress levels. Further analysis on the whole plant level led to the finding of tissue-specific or water-deficit levels specific regulation of transcription factors. Analysis of the over-represented motif of different gene groups revealed several new cis-elements associated with different levels of water deficit. The expression patterns of 18 genes were confirmed byquantitative reverse transcription polymerase chain reaction method and demonstrated the accuracy and effectiveness of RNA-Seq. The primary root specific transcriptome in soybean can enable a better understanding of the root response to water deficit conditions. The genes detected in root tissues that were associated with

Estimating time-varying conditional correlations between stock and foreign exchange markets

Science.gov (United States)

Tastan, Hüseyin

2006-02-01

This study explores the dynamic interaction between stock market returns and changes in nominal exchange rates. Many financial variables are known to exhibit fat tails and autoregressive variance structure. It is well-known that unconditional covariance and correlation coefficients also vary significantly over time and multivariate generalized autoregressive model (MGARCH) is able to capture the time-varying variance-covariance matrix for stock market returns and changes in exchange rates. The model is applied to daily Euro-Dollar exchange rates and two stock market indexes from the US economy: Dow-Jones Industrial Average Index and S&P500 Index. The news impact surfaces are also drawn based on the model estimates to see the effects of idiosyncratic shocks in respective markets.

varying elastic parameters distributions

KAUST Repository

Moussawi, Ali

2014-12-01

The experimental identication of mechanical properties is crucial in mechanics for understanding material behavior and for the development of numerical models. Classical identi cation procedures employ standard shaped specimens, assume that the mechanical elds in the object are homogeneous, and recover global properties. Thus, multiple tests are required for full characterization of a heterogeneous object, leading to a time consuming and costly process. The development of non-contact, full- eld measurement techniques from which complex kinematic elds can be recorded has opened the door to a new way of thinking. From the identi cation point of view, suitable methods can be used to process these complex kinematic elds in order to recover multiple spatially varying parameters through one test or a few tests. The requirement is the development of identi cation techniques that can process these complex experimental data. This thesis introduces a novel identi cation technique called the constitutive compatibility method. The key idea is to de ne stresses as compatible with the observed kinematic eld through the chosen class of constitutive equation, making possible the uncoupling of the identi cation of stress from the identi cation of the material parameters. This uncoupling leads to parametrized solutions in cases where 5 the solution is non-unique (due to unknown traction boundary conditions) as demonstrated on 2D numerical examples. First the theory is outlined and the method is demonstrated in 2D applications. Second, the method is implemented within a domain decomposition framework in order to reduce the cost for processing very large problems. Finally, it is extended to 3D numerical examples. Promising results are shown for 2D and 3D problems.

Experimental effects of immersion time and water temperature on body condition, burying depth and timing of spawning of the tellinid bivalve Macoma balthica

Science.gov (United States)

de Goeij, Petra; Honkoop, Pieter J.

2003-03-01

The burying depth of many bivalve molluscs on intertidal mudflats varies throughout the year and differs between places. Many factors are known to influence burying depth on a seasonal or spatial scale, with temperature and tidal regime probably being very important. Burying depth, body condition and gonadal development of Macoma balthica were followed throughout winter and spring in an experiment in which water temperature and immersion time were manipulated. Unexpectedly, relative water temperature, in contrast to the prediction, did not generally affect body condition or burying depth. This was probably a consequence of the exceptionally overall low water temperatures during the experimental winter. Differences in temperature did, however, result in different timing of spawning: M. balthica spawned earlier at higher spring temperatures. Longer immersion times led to higher body condition only late in spring, but led to deeper burying throughout almost the whole period. There was no effect of immersion time on the timing of spawning. We conclude that a longer immersion time leads to deeper burying, independent of body condition. We also conclude that burying behaviour of M. balthica is not determined by the moment of spawning.

Optimization of hydrostatic pressure at varied sonication conditions--power density, intensity, very low frequency--for isothermal ultrasonic sludge treatment.

Science.gov (United States)

Delmas, Henri; Le, Ngoc Tuan; Barthe, Laurie; Julcour-Lebigue, Carine

2015-07-01

This work aims at investigating for the first time the key sonication (US) parameters: power density (DUS), intensity (IUS), and frequency (FS) - down to audible range, under varied hydrostatic pressure (Ph) and low temperature isothermal conditions (to avoid any thermal effect). The selected application was activated sludge disintegration, a major industrial US process. For a rational approach all comparisons were made at same specific energy input (ES, US energy per solid weight) which is also the relevant economic criterion. The decoupling of power density and intensity was obtained by either changing the sludge volume or most often by changing probe diameter, all other characteristics being unchanged. Comprehensive results were obtained by varying the hydrostatic pressure at given power density and intensity. In all cases marked maxima of sludge disintegration appeared at optimum pressures, which values increased at increasing power intensity and density. Such optimum was expected due to opposite effects of increasing hydrostatic pressure: higher cavitation threshold then smaller and fewer bubbles, but higher temperature and pressure at the end of collapse. In addition the first attempt to lower US frequency down to audible range was very successful: at any operation condition (DUS, IUS, Ph, sludge concentration and type) higher sludge disintegration was obtained at 12 kHz than at 20 kHz. The same values of optimum pressure were observed at 12 and 20 kHz. At same energy consumption the best conditions - obtained at 12 kHz, maximum power density 720 W/L and 3.25 bar - provided about 100% improvement with respect to usual conditions (1 bar, 20 kHz). Important energy savings and equipment size reduction may then be expected. Copyright © 2014 Elsevier B.V. All rights reserved.

Corrosion study of API 5L x-series pipeline steels in 3.5% NaCl solution under varying conditions

International Nuclear Information System (INIS)

Shahid, M.; Qureshi, M.I.; Farooq, M.U.; Khan, M.I.

2003-01-01

Pipelines provide convenient and efficient means for mass transportation of variety of fluids, such as oil and gas, over varying distances. In the last two decades or so, pipeline designers focused mainly on the usage of larger sizes and higher operating pressures for achieving higher transportation efficiency. This has been accomplished through the provision of steels with progressive increase in yield strength coupled with good weldability and sufficient toughness to restrict crack propagation. In addition to higher strength and toughness, developing pipeline technologies have required improved resistance to corrosion, which has been tried with specific alloy additions and special control over non-metallic inclusions. Corrosion investigations were carried out on various grades of pipeline steels (API 5L X-46, X-52, X-56, X-60 and X- 70) under varying environmental conditions. This paper describes the results pertaining to corrosion behavior of the steels in 3.5% NaCl solutions in stagnant, turbulent and deaerated conditions. It was found that all grades corrode in this solution and their corrosion potentials and corrosion currents are in close vicinity of each other. Turbulent solutions, however, have shown an increase in corrosion rates whereas deaeration has revealed a relative decrease in aggressivity of the electrolyte. (author)

Conditioned responses elicited by experimentally produced cues for smoking.

Science.gov (United States)

Mucha, R F; Pauli, P; Angrilli, A

1998-03-01

Several theories of drug-craving postulate that a signal for drug elicits conditioned responses. However, depending on the theory, a drug cue is said to elicit drug similar, drug compensatory, positive motivational, and negative motivational effects. Since animal data alone cannot tease apart the relative importance of different cue-related processes in the addict, we developed and examined a model of drug cues in the human based on a two-sound, differential conditioning procedure using smoking as the reinforcer. After multiple pairings of a sound with smoking, there was a preference for the smoking cue on a conditioned preference test. The acute effects of smoking (increased heart rate, respiration rate, skin conductance level, skin conductance fluctuations, EEG beta power and trapezius EMG, decreased alpha power) were not affected by the smoking cue, although subjects drew more on their cigarette in the presence of the smoking cue than in the presence of a control cue. Moreover, the cue did not change baseline behaviour except for a possible increase in EEG beta power and an increase in trapezius EMG at about the time when smoking should have occurred. The findings confirm the value of experimental models of drug cues in the human for comparing different cue phenomena in the dependent individual. They indicate that an acquired signal for drug in the human may elicit incentive motivational effects and associated preparatory motor responses in addition to possible conditioned tolerance.

An experimental study of low concentration sludge settling velocity under turbulent condition.

Science.gov (United States)

Guo, Lisha; Zhang, Daijun; Xu, Danyu; Chen, Yuan

2009-05-01

Particle Image Velocimetry (PIV) was used to study the settling of activated sludge flocs under turbulent flow conditions. Experimental results showed that a larger particle diameter led to a higher settling velocity while the higher turbulence intensity led to lower settling velocity. Based on the measurements a mathematical relation has been derived which correlates the settling velocity for individual sludge flocs under turbulent conditions through a modified Vesilind equation. Settling velocity shows a power-type relation to sludge particle diameter and an exponential-type relation with turbulence intensity and sludge concentration.

Wind conditions in urban layout - Numerical and experimental research

Science.gov (United States)

Poćwierz, Marta; Zielonko-Jung, Katarzyna

2018-01-01

This paper presents research which compares the numerical and the experimental results for different cases of airflow around a few urban layouts. The study is concerned mostly with the analysis of parameters, such as pressure and velocity fields, which are essential in the building industry. Numerical simulations have been performed by the commercial software Fluent, with the use of a few different turbulence models, including popular k-ɛ, k-ɛ realizable or k-ω. A particular attention has been paid to accurate description of the conditions on the inlet and the selection of suitable computing grid. The pressure measurement near buildings and oil visualization were undertaken and described accordingly.

Time-varying output performances of piezoelectric vibration energy harvesting under nonstationary random vibrations

Science.gov (United States)

Yoon, Heonjun; Kim, Miso; Park, Choon-Su; Youn, Byeng D.

2018-01-01

Piezoelectric vibration energy harvesting (PVEH) has received much attention as a potential solution that could ultimately realize self-powered wireless sensor networks. Since most ambient vibrations in nature are inherently random and nonstationary, the output performances of PVEH devices also randomly change with time. However, little attention has been paid to investigating the randomly time-varying electroelastic behaviors of PVEH systems both analytically and experimentally. The objective of this study is thus to make a step forward towards a deep understanding of the time-varying performances of PVEH devices under nonstationary random vibrations. Two typical cases of nonstationary random vibration signals are considered: (1) randomly-varying amplitude (amplitude modulation; AM) and (2) randomly-varying amplitude with randomly-varying instantaneous frequency (amplitude and frequency modulation; AM-FM). In both cases, this study pursues well-balanced correlations of analytical predictions and experimental observations to deduce the relationships between the time-varying output performances of the PVEH device and two primary input parameters, such as a central frequency and an external electrical resistance. We introduce three correlation metrics to quantitatively compare analytical prediction and experimental observation, including the normalized root mean square error, the correlation coefficient, and the weighted integrated factor. Analytical predictions are in an excellent agreement with experimental observations both mechanically and electrically. This study provides insightful guidelines for designing PVEH devices to reliably generate electric power under nonstationary random vibrations.

Pemodelan Markov Switching Dengan Time-varying Transition Probability

OpenAIRE

Savitri, Anggita Puri; Warsito, Budi; Rahmawati, Rita

2016-01-01

Exchange rate or currency is an economic variable which reflects country's state of economy. It fluctuates over time because of its ability to switch the condition or regime caused by economic and political factors. The changes in the exchange rate are depreciation and appreciation. Therefore, it could be modeled using Markov Switching with Time-Varying Transition Probability which observe the conditional changes and use information variable. From this model, time-varying transition probabili...

Development of experimental data bank on heat transfer crisis under stationary conditions

International Nuclear Information System (INIS)

Koshtyalek, Ya.

1982-01-01

The development of an experimental data bank on heat transfer orisis under stationary conditions is discussed. The work is being carried out under the auspices of CMEA in compliance with the resolution of CMEA countries experts meetinq in January 1981 held in Moscow. The data bank is supposed to be formed as a sequential set of available experimental data on the regimes with heat-transfer crisis, recorded on a standard magnetic tape for ES or IBM comuter family. All operations with the bank are to be performed via the computer. Recommendations are given to what the record structure should be used and an example of a code is suggested for a user to extract data from the bank in accordance with various criteria. At the present time parameters of more than 12000 experimental regimes are prepared for the bank and some 3000 more are being processed [ru

Experimental study of elliptical jet from sub to supercritical conditions

Energy Technology Data Exchange (ETDEWEB)

Muthukumaran, C. K.; Vaidyanathan, Aravind, E-mail: aravind7@iist.ac.in [Department of Aerospace Engineering, Indian Institute of Space Science and Technology, Trivandrum, Kerala 695547 (India)

2014-04-15

The jet mixing at supercritical conditions involves fluid dynamics as well as thermodynamic phenomena. All the jet mixing studies at critical conditions to the present date have focused only on axisymmetric jets. When the liquid jet is injected into supercritical environment, the thermodynamic transition could be well understood by considering one of the important fluid properties such as surface tension since it decides the existence of distinct boundary between the liquid and gaseous phase. It is well known that an elliptical liquid jet undergoes axis-switching phenomena under atmospheric conditions due to the presence of surface tension. The experimental investigations were carried out with low speed elliptical jet under supercritical condition. Investigation of the binary component system with fluoroketone jet and N{sub 2} gas as environment shows that the surface tension force dominates for a large downstream distance, indicating delayed thermodynamic transition. The increase in pressure to critical state at supercritical temperature is found to expedite the thermodynamic transition. The ligament like structures has been observed rather than droplets for supercritical pressures. However, for the single component system with fluoroketone jet and fluoroketone environment shows that the jet disintegrates into droplets as it is subjected to the chamber conditions even for the subcritical pressures and no axis switching phenomenon is observed. For a single component system, as the pressure is increased to critical state, the liquid jet exhibits gas-gas like mixing behavior and that too without exhibiting axis-switching behavior.

Experimental FSO network availability estimation using interactive fog condition monitoring

Science.gov (United States)

Turán, Ján.; Ovseník, Łuboš

2016-12-01

Free Space Optics (FSO) is a license free Line of Sight (LOS) telecommunication technology which offers full duplex connectivity. FSO uses infrared beams of light to provide optical broadband connection and it can be installed literally in a few hours. Data rates go through from several hundreds of Mb/s to several Gb/s and range is from several 100 m up to several km. FSO link advantages: Easy connection establishment, License free communication, No excavation are needed, Highly secure and safe, Allows through window connectivity and single customer service and Compliments fiber by accelerating the first and last mile. FSO link disadvantages: Transmission media is air, Weather and climate dependence, Attenuation due to rain, snow and fog, Scattering of laser beam, Absorption of laser beam, Building motion and Air pollution. In this paper FSO availability evaluation is based on long term measured data from Fog sensor developed and installed at TUKE experimental FSO network in TUKE campus, Košice, Slovakia. Our FSO experimental network has three links with different physical distances between each FSO heads. Weather conditions have a tremendous impact on FSO operation in terms of FSO availability. FSO link availability is the percentage of time over a year that the FSO link will be operational. It is necessary to evaluate the climate and weather at the actual geographical location where FSO link is going to be mounted. It is important to determine the impact of a light scattering, absorption, turbulence and receiving optical power at the particular FSO link. Visibility has one of the most critical influences on the quality of an FSO optical transmission channel. FSO link availability is usually estimated using visibility information collected from nearby airport weather stations. Raw data from fog sensor (Fog Density, Relative Humidity, Temperature measured at each ms) are collected and processed by FSO Simulator software package developed at our Department. Based

Instability of automotive air conditioning system with a variable displacement compressor. Part 1. Experimental investigation

Energy Technology Data Exchange (ETDEWEB)

Tian, Changqing; Dou, Chunpeng; Yang, Xinjiang; Li, Xianting [Department of Building Science, School of Architecture, Tsinghua University, Beijing 100084 (People' s Republic of China)

2005-11-01

A test system is built first in order to investigate the instability of the automotive air conditioning (AAC) system with a variable displacement compressor (VDC), and hunting phenomena caused by the large external disturbance in the AAC system with a VDC and a thermal expansion valve, and in the AAC system with a VDC and a fixed-area throttling device are investigated experimentally in part 1 of this paper. The experimental results indicate that there also exist the hunting phenomena in the AAC system with a fixed-area throttling device. The system stability is found to be dependent on the direction of the external disturbance, and the system is apt to cause hunting when the condensing pressure decreases excessively since it may cause two-phase state at the throttling device inlet and make a large disturbance to the system. The piston stroke length will oscillate only when the oscillation amplitudes of forces acting on the wobble plate are great enough, otherwise the piston stroke length will be kept invariable, and then the system instability rule is also suitable for the AAC system with a fixed displacement compressor. From the experimental results, it is concluded that the two-phase flow at the throttling device inlet or at the evaporator outlet is the necessary condition but not sufficient condition for system hunting. Finally, a new concept, conservative stable region, is proposed based on the experimental results and theoretical analysis. (author)

Adaptive Neural Network Control for Nonlinear Hydraulic Servo-System with Time-Varying State Constraints

Directory of Open Access Journals (Sweden)

Shu-Min Lu

2017-01-01

Full Text Available An adaptive neural network control problem is addressed for a class of nonlinear hydraulic servo-systems with time-varying state constraints. In view of the low precision problem of the traditional hydraulic servo-system which is caused by the tracking errors surpassing appropriate bound, the previous works have shown that the constraint for the system is a good way to solve the low precision problem. Meanwhile, compared with constant constraints, the time-varying state constraints are more general in the actual systems. Therefore, when the states of the system are forced to obey bounded time-varying constraint conditions, the high precision tracking performance of the system can be easily realized. In order to achieve this goal, the time-varying barrier Lyapunov function (TVBLF is used to prevent the states from violating time-varying constraints. By the backstepping design, the adaptive controller will be obtained. A radial basis function neural network (RBFNN is used to estimate the uncertainties. Based on analyzing the stability of the hydraulic servo-system, we show that the error signals are bounded in the compacts sets; the time-varying state constrains are never violated and all singles of the hydraulic servo-system are bounded. The simulation and experimental results show that the tracking accuracy of system is improved and the controller has fast tracking ability and strong robustness.

Thermal shock behaviour of different tungsten grades under varying conditions

Energy Technology Data Exchange (ETDEWEB)

Wirtz, Oliver Marius

2012-07-19

Thermonuclear fusion power plants are a promising option to ensure the energy supply for future generations, but in many fields of research enormous challenges have to be faced. A major step on the way to the prototype fusion reactor DEMO will be ITER which is build in Cadarache, southern France. One of the most critical issues is the field of in-vessel materials and components, in particular the plasma facing materials (PFM). PFMs that will be used in a device like ITER have to withstand severe environmental conditions in terms of steady state and transient thermal loads as well as high particle fluxes such as hydrogen, helium and neutrons. Candidate wall materials are beryllium, tungsten and carbon based materials like CFC (carbon fibre composite). Tungsten is the most promising material for an application in the divertor region with very severe loading conditions and it will most probably also be used as PFM for DEMO. Hence, this work focuses on the investigation of the thermal shock response of different tungsten grades in order to understand the damage mechanisms and to identify material parameters which influence this behaviour under ITER and DEMO relevant operation conditions. Therefore the microstructure and the mechanical and thermal properties of five industrially manufactured tungsten grades were characterised. All five tungsten grades were exposed to transient thermal events with very high power densities of up to 1.27 GWm{sup -2} at varying base temperatures between RT and 600 C in the electron beam device JUDITH 1. The pulse numbers were limited to a maximum of 1000 in order to avoid immoderate workload on the test facility and to have enough time to cover a wide range of loading conditions. The results of this damage mapping enable to define different damage and cracking thresholds for the investigated tungsten grades and to identify certain material parameters which influence the location of these thresholds and the distinction of the induced

Thermal shock behaviour of different tungsten grades under varying conditions

International Nuclear Information System (INIS)

Wirtz, Oliver Marius

2012-01-01

Thermonuclear fusion power plants are a promising option to ensure the energy supply for future generations, but in many fields of research enormous challenges have to be faced. A major step on the way to the prototype fusion reactor DEMO will be ITER which is build in Cadarache, southern France. One of the most critical issues is the field of in-vessel materials and components, in particular the plasma facing materials (PFM). PFMs that will be used in a device like ITER have to withstand severe environmental conditions in terms of steady state and transient thermal loads as well as high particle fluxes such as hydrogen, helium and neutrons. Candidate wall materials are beryllium, tungsten and carbon based materials like CFC (carbon fibre composite). Tungsten is the most promising material for an application in the divertor region with very severe loading conditions and it will most probably also be used as PFM for DEMO. Hence, this work focuses on the investigation of the thermal shock response of different tungsten grades in order to understand the damage mechanisms and to identify material parameters which influence this behaviour under ITER and DEMO relevant operation conditions. Therefore the microstructure and the mechanical and thermal properties of five industrially manufactured tungsten grades were characterised. All five tungsten grades were exposed to transient thermal events with very high power densities of up to 1.27 GWm -2 at varying base temperatures between RT and 600 C in the electron beam device JUDITH 1. The pulse numbers were limited to a maximum of 1000 in order to avoid immoderate workload on the test facility and to have enough time to cover a wide range of loading conditions. The results of this damage mapping enable to define different damage and cracking thresholds for the investigated tungsten grades and to identify certain material parameters which influence the location of these thresholds and the distinction of the induced damages

Experimental and numerical investigation of centrifugal pumps with asymmetric inflow conditions

Science.gov (United States)

Mittag, Sten; Gabi, Martin

2015-11-01

Most of the times pumps operate off best point states. Reasons are changes of operating conditions, modifications, pollution and wearout or erosion. As consequences non-rotational symmetric flows, transient operational conditions, increased risk of cavitation, decrease of efficiency and unpredictable wearout can appear. Especially construction components of centrifugal pumps, in particular intake elbows, contribute to this matter. Intake elbows causes additional losses and secondary flows, hence non-rotational velocity distributions as intake profile to the centrifugal pump. As a result the impeller vanes experience permanent changes of the intake flow angle and with it transient flow conditions in the blade channels. This paper presents the first results of a project, experimentally and numerically investigating the consequences of non-rotational inflow to leading edge flow conditions of a centrifugal pump. Therefore two pumpintake- elbow systems are compared, by only altering the intake elbow geometry: a common single bended 90° elbow and a numerically optimized elbow (improved regarding rotational symmetric inflow conditions and friction coefficient). The experiments are carried out, using time resolved stereoscopic PIV on a full acrylic pump with refractions index matched (RIM) working fluid. This allows transient investigations of the flow field simultaneously for all blade leading edges. Additional CFD results are validated and used to further support the investigation i.e. for comparing an analog pump system with ideal inflow conditions.

Experimental determination of the boundary condition for diffuse photons in a homogeneous turbid medium

International Nuclear Information System (INIS)

Everitt, David L.; Zhu, Tuo; Zhu, H.-M.; Zhu, X. D.

2000-01-01

We present a simple experimental method that permits an empirical determination of the effective boundary condition and the extrapolated end point for the diffuse photon density in a homogeneous turbid medium. (c) 2000 Optical Society of America

Presentation and comparison of experimental critical heat flux data at conditions prototypical of light water small modular reactors

Energy Technology Data Exchange (ETDEWEB)

Greenwood, M.S., E-mail: 1greenwoodms@ornl.gov; Duarte, J.P.; Corradini, M.

2017-06-15

Highlights: • Low mass flux and moderate to high pressure CHF experimental results are presented. • Facility uses chopped-cosine heater profile in a 2 × 2 square bundle geometry. • The EPRI, CISE-GE, and W-3 CHF correlations provide reasonable average CHF prediction. • Neural network analysis predicts experimental data and demonstrates utility of method. - Abstract: The critical heat flux (CHF) is a two-phase flow phenomenon which rapidly decreases the efficiency of the heat transfer performance at a heated surface. This phenomenon is one of the limiting criteria in the design and operation of light water reactors. Deviations of operating parameters greatly alters the CHF condition and must be experimentally determined for any new parameters such as those proposed in small modular reactors (SMR) (e.g. moderate to high pressure and low mass fluxes). Current open literature provides too little data for functional use at the proposed conditions of prototypical SMRs. This paper presents a brief summary of CHF data acquired from an experimental facility at the University of Wisconsin-Madison designed and built to study CHF at high pressure and low mass flux ranges in a 2 × 2 chopped cosine rod bundle prototypical of conceptual SMR designs. The experimental CHF test inlet conditions range from pressures of 8–16 MPa, mass fluxes of 500–1600 kg/m2 s, and inlet water subcooling from 250 to 650 kJ/kg. The experimental data is also compared against several accepted prediction methods whose application ranges are most similar to the test conditions.

Behavior of a PCM at Varying Heating Rates: Experimental and Theoretical Study with an Aim at Temperature Moderation in Radionuclide Concrete Encasements

Science.gov (United States)

Medved', Igor; Trník, Anton

2018-07-01

Phase-change materials (PCMs) can store/release thermal energy within a small temperature range. This is of interest in various industrial applications, for example, in civil engineering (heating/cooling of buildings) or cold storage applications. Another application may be the moderation of temperature increases in concrete encasements of radionuclides during their decay. The phase-change behavior of a material is determined by its heat capacity and the peak it exhibits near a phase change. We analyze the behavior of such peaks for a selected PCM at heating rates varying between 0.1°C\\cdot min^{-1} and 1°C\\cdot min^{-1}, corresponding in real situations to different decay rates of radionuclides. We show that experimentally measured peaks can be plausibly described by an equilibrium theory that enables us to calculate the latent heat and phase-change temperature from experimental data.

Possibilities of pharmacologic correction of cognitive disorders in conditions of experimental equivalent of multiple sclerosis

Directory of Open Access Journals (Sweden)

Nefyodov A.A.

2015-06-01

Full Text Available A comparative analysis of the impact of citicoline, ±-lipoic acid, nicergoline, donepezil and colloidal solution of nano-silver (CSNS on the processes of learning and consolidation of memorable track in the test of the conditional reaction of passive avoidance (CRPA in conditions of experimental allergic encephalomyelitis (EAE was conducted. Testing of passive defensive skill was performed on days 12 and 20 after the induction of EAE. To assess the impact of drugs on the inputted information processes the investigated substances were administered intragastrically (CSNS - intraperitoneally once daily in the definite dose from the second to the day 10 after the induction of EAE (latent phase of the disease, and assessing processes of conditional skill preserving, further administration of drugs by the day 20 of the experiment (average duration of EAE was used. A positive effect of citicoline, ±-lipoic acid, nicergoline and donepezil on the input information processes and the ability to prevent accelerated extinction of acquired contingent skill in the conditions of experimental pathology was established. Drugs statistically significantly increased duration of the latent period of CRPA in comparison with a group of active control by 49%, 43%, 39% and 34%, respectively. Here with preparations were characterized by a high coefficient of antiamnesic activity, by the end of the experiment it was recorded at the level of 95% (citicoline, 81% (±-lipoic acid, 76% (nicergoline and 53% (donepezil. It is shown that the ability to prevent development of cognitive impairment in conditions of experimental equivalent of multiple sclerosis decreases in the number of citicoline (500 mg/kg > ±-lipoic acid (50 mg/kg H nicergoline (10 mg/kg > donepezil (10 mg/kg.

Development of Fuzzy Logic Control for Vehicle Air Conditioning System

Directory of Open Access Journals (Sweden)

Henry Nasution

2008-08-01

Full Text Available A vehicle air conditioning system is experimentally investigated. Measurements were taken during the experimental period at a time interval of one minute for a set point temperature of 22, 23 and 24oC with internal heat loads of 0, 1 and 2 kW. The cabin temperature and the speed of the compressor were varied and the performance of the system, energy consumption and energy saving ware analyzed. The main objective of the experimental work is to evaluate the energy saving obtained when the fuzzy logic control (FLC algorithm, through an inverter, continuously regulates the compressor speed. It demonstrates better control of the compressor operation in terms of energy consumption as compared to the control by using a thermostat imposing On/Off cycles on the compressor at the nominal frequency of 50 Hz. The experimental set-up consists of original components from the air conditioning system of a compact passenger vehicle. The experimental results indicate that the proposed technique can save energy and improve indoor comfort significantly for vehicle air conditioning systems compared to the conventional (On/Off control technique.

An experimental test of condition-dependent male and female mate choice in zebra finches.

Directory of Open Access Journals (Sweden)

Marie-Jeanne Holveck

Full Text Available In mating systems with social monogamy and obligatory bi-parental care, such as found in many songbird species, male and female fitness depends on the combined parental investment. Hence, both sexes should gain from choosing mates in high rather than low condition. However, theory also predicts that an individual's phenotypic quality can constrain choice, if low condition individuals cannot afford prolonged search efforts and/or face higher risk of rejection. In systems with mutual mate choice, the interaction between male and female condition should thus be a better predictor of choice than either factor in isolation. To address this prediction experimentally, we manipulated male and female condition and subsequently tested male and female mating preferences in zebra finches Taeniopygia guttata, a songbird species with mutual mate choice and obligatory bi-parental care. We experimentally altered phenotypic quality by manipulating the brood size in which the birds were reared. Patterns of association for high- or low-condition individuals of the opposite sex differed for male and female focal birds when tested in an 8-way choice arena. Females showed repeatable condition-assortative preferences for males matching their own rearing background. Male preferences were also repeatable, but not predicted by their own or females' rearing background. In combination with a brief review of the literature on condition-dependent mate choice in the zebra finch we discuss whether the observed sex differences and between-studies differences arise because males and females differ in context sensitivity (e.g. male-male competition suppressing male mating preferences, sampling strategies or susceptibility to rearing conditions (e.g. sex-specific effect on physiology. While a picture emerges that juvenile and current state indeed affect preferences, the development and context-dependency of mutual state-dependent mate choice warrants further study.

Experimental and theoretical study of electronic structure of aluminum in extreme conditions with X-ray absorption spectroscopy

International Nuclear Information System (INIS)

Festa, Floriane

2013-01-01

Matter in extreme conditions belongs to Warm Dense Matter regime which lays between dense plasma regime and condensed matter. This regime is still not well known, indeed it is very complex to generate such plasma in the laboratory to get experimental data and validate models. The goal of this thesis is to study electronic structure of aluminum in extreme conditions with X-ray absorption spectroscopy. Experimentally aluminum has reached high densities and high temperatures, up to now unexplored. An X-ray source has also been generated to probe highly compressed aluminum. Two spectrometers have recorded aluminum absorption spectra and aluminum density and temperature conditions have been deduced thanks to optical diagnostics. Experimental spectra have been compared to ab initio spectra, calculated in the same conditions. The theoretical goal was to validate the calculation method in high densities and high temperatures regime with the study of K-edge absorption modifications. We also used absorption spectra to study the metal-non metal transition which takes place at low density (density ≤ solid density). This transition could be study with electronic structure modifications of the system. (author) [fr

Optimization of experimental conditions for composite biodiesel production from transesterification of mixed oils of Jatropha and Pongamia

Energy Technology Data Exchange (ETDEWEB)

Yogish, H.; Chandrashekara, K.; Pramod Kumar, M.R. [S.J. College of Engineering, Department of Mechanical Engineering, Mysore (India)

2012-11-15

India is looking at the renewable alternative sources of energy to reduce its dependence on import of crude oil. As India imports 70 % of the crude oil, the country has been greatly affected by increasing cost and uncertainty. Biodiesel fuel derived by the two step acid transesterification of mixed non-edible oils from Jatropha curcas and Pongamia (karanja) can meet the requirements of diesel fuel in the coming years. In the present study, different proportions of Methanol, Sodium hydroxide, variation of Reaction time, Sulfuric acid and Reaction Temperature were adopted in order to optimize the experimental conditions for maximum biodiesel yield. The preliminary studies revealed that biodiesel yield varied widely in the range of 75-95 % using the laboratory scale reactor. The average yield of 95 % was obtained. The fuel and chemical properties of biodiesel, namely kinematic viscosity, specific gravity, density, flash point, fire point, calorific value, pH, acid value, iodine value, sulfur content, water content, glycerin content and sulfated ash values were found to be within the limits suggested by Bureau of Indian Standards (BIS 15607: 2005). The optimum combination of Methanol, Sodium hydroxide, Sulfuric acid, Reaction Time and Reaction Temperature are established. (orig.)

Optimization of experimental conditions for composite biodiesel production from transesterification of mixed oils of Jatropha and Pongamia

Science.gov (United States)

Yogish, H.; Chandrashekara, K.; Pramod Kumar, M. R.

2012-11-01

India is looking at the renewable alternative sources of energy to reduce its dependence on import of crude oil. As India imports 70 % of the crude oil, the country has been greatly affected by increasing cost and uncertainty. Biodiesel fuel derived by the two step acid transesterification of mixed non-edible oils from Jatropha curcas and Pongamia (karanja) can meet the requirements of diesel fuel in the coming years. In the present study, different proportions of Methanol, Sodium hydroxide, variation of Reaction time, Sulfuric acid and Reaction Temperature were adopted in order to optimize the experimental conditions for maximum biodiesel yield. The preliminary studies revealed that biodiesel yield varied widely in the range of 75-95 % using the laboratory scale reactor. The average yield of 95 % was obtained. The fuel and chemical properties of biodiesel, namely kinematic viscosity, specific gravity, density, flash point, fire point, calorific value, pH, acid value, iodine value, sulfur content, water content, glycerin content and sulfated ash values were found to be within the limits suggested by Bureau of Indian Standards (BIS 15607: 2005). The optimum combination of Methanol, Sodium hydroxide, Sulfuric acid, Reaction Time and Reaction Temperature are established.

Contact conditions in skin-pass rolling

DEFF Research Database (Denmark)

Kijima, Hideo; Bay, Niels

2007-01-01

The special contact conditions in skin-pass rolling of steel strip is analysed by studying plane strain upsetting of thin sheet with low reduction applying long narrow tools and dry friction conditions. An extended sticking region is estimated by an elasto-plastic FEM analysis of the plane strain...... upsetting. This sticking region causes a highly inhomogeneous elasto-plastic deformation with large influence of work-hardening and friction. A numerical analysis of skin-pass rolling shows the same contact conditions, i.e. an extended sticking region around the center of the contact zone. The calculated...... size of the sticking region with varying contact length and pressure/reduction is experimentally verified by plane strain upsetting tests measuring the local surface deformation of the work pieces after unloading....

Experimental analysis of an air-to-air heat recovery unit for balanced ventilation systems in residential buildings

International Nuclear Information System (INIS)

Fernandez-Seara, Jose; Diz, Ruben; Uhia, Francisco J.; Dopazo, Alberto; Ferro, Jose M.

2011-01-01

This paper deals with the experimental analysis of an air-to-air heat recovery unit equipped with a sensible polymer plate heat exchanger (PHE) for balanced ventilation systems in residential buildings. The PHE is arranged in parallel triangular ducts. An experimental facility was designed to reproduce the typical outdoor and exhaust air conditions with regard to temperature and humidity. The unit was tested under balanced operation conditions, as commonly used in practice. A set of tests was conducted under the reference operating conditions to evaluate the PHE performance. Afterwards, an experimental parametric analysis was conducted to investigate the influence of changing the operating conditions on the PHE performance. Experiments were carried out varying the inlet fresh air temperature, the exhaust air relative humidity and the air flow rate. The experimental results are shown and discussed in this paper.

QEEG Spectral and Coherence Assessment of Autistic Children in Three Different Experimental Conditions

Science.gov (United States)

Machado, Calixto; Estévez, Mario; Leisman, Gerry; Melillo, Robert; Rodríguez, Rafael; DeFina, Phillip; Hernández, Adrián; Pérez-Nellar, Jesús; Naranjo, Rolando; Chinchilla, Mauricio; Garófalo, Nicolás; Vargas, José; Beltrán, Carlos

2015-01-01

We studied autistics by quantitative EEG spectral and coherence analysis during three experimental conditions: basal, watching a cartoon with audio (V-A), and with muted audio band (VwA). Significant reductions were found for the absolute power spectral density (PSD) in the central region for delta and theta, and in the posterior region for sigma…

Experimental study of horizontal annular channels under non-developed conditions

International Nuclear Information System (INIS)

Delgadino, G.; Balino, J.; Carrica, P.

1995-01-01

In this work an experimental study of the two-phase air-water flow in a horizontal annular channel under non-developed conditions is presented. A conductive local probe was placed at the end of the channel to measure the local phase indication function under a wide range of gas and water flow rates. The signal was processed to obtain the void fraction and statistical distributions of liquid and gas residence times. From these data the topology of the flow could be inferred. A laser intermittence detector was also located close to the channel exit, in order to measure statistical parameters for intermittent flows by means of a two-probe method

Experimental study of horizontal annular channels under non-developed conditions

Energy Technology Data Exchange (ETDEWEB)

Delgadino, G. [Rensselaer Polytechnic Institute, Troy, NY (United States); Balino, J.; Carrica, P. [Centro Atomico Bariloche e Instituto Balseriro (Argentina)

1995-09-01

In this work an experimental study of the two-phase air-water flow in a horizontal annular channel under non-developed conditions is presented. A conductive local probe was placed at the end of the channel to measure the local phase indication function under a wide range of gas and water flow rates. The signal was processed to obtain the void fraction and statistical distributions of liquid and gas residence times. From these data the topology of the flow could be inferred. A laser intermittence detector was also located close to the channel exit, in order to measure statistical parameters for intermittent flows by means of a two-probe method.

Rolling Friction Torque in Ball-Race Contacts Operating in Mixed Lubrication Conditions

Directory of Open Access Journals (Sweden)

Mihaela Rodica D. Bălan

2015-04-01

Full Text Available Based on a theoretical model and an experimental methodology for defining the friction torque for lubricated conditions in a modified thrust ball bearing having only three balls, the authors experimentally investigated the influence of the lubricant parameter Λ on friction torque for mixed IVR (isoviscous rigid and EHL (elastohydrodynamic lubrication conditions. The experiments were conducted using ball diameters of 3 mm, 3.97 mm and 6.35 mm loaded at 0.125 N, 0.400 N and 0.633 N. Two oils of viscosity 0.08 Pa·s and 0.05 Pa·s were used and rotational speed was varied in the range 60–210 rpm to obtain a lubricant parameter Λ varying between 0.3 and 3.2. The experiments confirmed that the measured friction torque can be explained using hydrodynamic rolling force relationships respecting the transition from an IVR to an EHL lubrication regime.

Fuel performance under normal PWR conditions: A review of relevant experimental results and models

Science.gov (United States)

Charles, M.; Lemaignan, C.

1992-06-01

Experiments conducted at Grenoble (CEA/DRN) over the past 20 years in the field of nuclear fuel behaviour are reviewed. Of particular concern is the need to achieve a comprehensive understanding of and subsequently overcome the limitations associated with high burnup and load-following conditions (pellet-cladding interaction (PCI), fission gas release (FGR), water-side corrosion). A general view is given of the organization of research work as well as some experimental details (irradiation, postirradiation examination — PIE). Based on various experimental programmes (Cyrano, Medicis, Anemone, Furet, Tango, Contact, Cansar, Hatac, Flog, Decor), the main contributions of the thermomechanical behaviour of a PWR fuel rod are described: thermal conductivity, in-pile densification, swelling, fission gas release in steady state and moderate transient conditions, gap thermal conductance, formation of primary and secondary ridges under PCI conditions. Specific programmes (Gdgrif, Thermox, Grimox) are devoted to the behaviour of particular fuels (gadolinia-bearing fuel, MOX fuel). Moreover, microstructure-based studies have been undertaken on fission gas release (fine analysis of the bubble population inside irradiated fuel samples), and on cladding behaviour (PCI related studies on stress-corrosion cracking (SCO, irradiation effects on zircaloy microstructure).

Natural circulation cooling in a PWR geometry under accident-induced conditions

International Nuclear Information System (INIS)

Shimeck, D.J.; Johnsen, G.W.

1983-01-01

The characteristics and limits of natural circulation heat rejection over a wide range of conditions were experimentally investigated in a small-scale model of a pressurized water reactor. Conditions that were varied included primary and secondary coolant inventory, decay heat power, and primary noncondensable gas content. The results have defined three distinct modes of natural circulation, their limits and transition points, and the characteristic signatures accompanying natural circulation behavior. Particular emphasis is focused on the limits of natural circulation under severely degraded primary and secondary conditions

Phytoremdiation Species And Their Modification Under By Weed Varying Climatic Condition A Changing Scenario

Directory of Open Access Journals (Sweden)

Anita Singh

2015-08-01

Full Text Available Abstract The major reasons for environmental contamination are population explosion increase in industrial and other urban activities. One of the consequent effect of these activities is heavy metal pollution. It is one of the serious issue to be discussed by the scientists and academicians that how to solve this problem to protect the environment. As heavy metals are non-biodegradable so they require effective cleanup technology. Most of the traditional methods such as excavation solidification and burial are very costly or they simply involve the isolation of the metals from contaminated sites. Among different technologies phytoremediation is best approach for removing metal contamination from environment. It involves plants to remove detoxify or immobilize metals from environment. Weed plants are found to be play very important role in metal remediation. They get affected by climatic variation which is also a consequent effect of environmental pollution. The physiology of plants as well as physiochemical properties of soil gets affected by varying climatic condition. Therefore the present review gives the information on metal remediation processes and how these process particularly phytoremediation by weed plants get affected by climatic changes.

Optimization of Experimental Conditions of the Pulsed Current GTAW Parameters for Mechanical Properties of SDSS UNS S32760 Welds Based on the Taguchi Design Method

Science.gov (United States)

Yousefieh, M.; Shamanian, M.; Saatchi, A.

2012-09-01

Taguchi design method with L9 orthogonal array was implemented to optimize the pulsed current gas tungsten arc welding parameters for the hardness and the toughness of super duplex stainless steel (SDSS, UNS S32760) welds. In this regard, the hardness and the toughness were considered as performance characteristics. Pulse current, background current, % on time, and pulse frequency were chosen as main parameters. Each parameter was varied at three different levels. As a result of pooled analysis of variance, the pulse current is found to be the most significant factor for both the hardness and the toughness of SDSS welds by percentage contribution of 71.81 for hardness and 78.18 for toughness. The % on time (21.99%) and the background current (17.81%) had also the next most significant effect on the hardness and the toughness, respectively. The optimum conditions within the selected parameter values for hardness were found as the first level of pulse current (100 A), third level of background current (70 A), first level of % on time (40%), and first level of pulse frequency (1 Hz), while they were found as the second level of pulse current (120 A), second level of background current (60 A), second level of % on time (60%), and third level of pulse frequency (5 Hz) for toughness. The Taguchi method was found to be a promising tool to obtain the optimum conditions for such studies. Finally, in order to verify experimental results, confirmation tests were carried out at optimum working conditions. Under these conditions, there were good agreements between the predicted and the experimental results for the both hardness and toughness.

Experimental investigation on the causes for pellet fragmentation under LOCA conditions

International Nuclear Information System (INIS)

Bianco, Andrea

2015-01-01

An experimental investigation was conducted in hot cells on single fuel rod segments to appraise the behavior of fuel pellets fragmentation during a loss of coolant accident in a light water reactor. In pursuing the conceptual design of the experiment, calculations were performed to study the thermal-hydraulics boundary conditions and the fuel rod behavior during the transient. The experiment's results encompass non-destructive and destructive examinations. In order to describe the resulting fuel fragments size distribution, a semi-empirical correlation was derived from the fractal theory.

Influence of experimental conditions on atom column visibility in energy dispersive X-ray spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Dycus, J.H.; Xu, W.; Sang, X. [Department of Materials Science and Engineering, North Carolina State University, 911 Partners Way Engineering Building 1, Raleigh, NC 27606 (United States); D' Alfonso, A.J. [School of Physics, University of Melbourne, Parkville, Victoria 3010 (Australia); Chen, Z. [School of Physics and Astronomy, Monash University, Clayton, Victoria 3800 (Australia); Weyland, M. [Monash Centre for Electron Microscopy, Monash University, Clayton, Victoria 3800 (Australia); Department of Materials Science and Engineering, Monash University, Clayton, Victoria 3800 (Australia); Allen, L.J. [School of Physics, University of Melbourne, Parkville, Victoria 3010 (Australia); Findlay, S.D. [School of Physics and Astronomy, Monash University, Clayton, Victoria 3800 (Australia); LeBeau, J.M., E-mail: jmlebeau@ncsu.edu [Department of Materials Science and Engineering, North Carolina State University, 911 Partners Way Engineering Building 1, Raleigh, NC 27606 (United States)

2016-12-15

Here we report the influence of key experimental parameters on atomically resolved energy dispersive X-ray spectroscopy (EDX). In particular, we examine the role of the probe forming convergence semi-angle, sample thickness, lattice spacing, and dwell/collection time. We show that an optimum specimen-dependent probe forming convergence angle exists to maximize the signal-to-noise ratio of the atomically resolved signal in EDX mapping. Furthermore, we highlight that it can be important to select an appropriate dwell time to efficiently process the X-ray signal. These practical considerations provide insight for experimental parameters in atomic resolution energy dispersive X-ray analysis. - Highlights: • Impacts of microscope operating conditions on EDX signal and atom column contrast are demonstrated. • Influence of sample thickness and lattice spacing is shown. • Conditions for obtaining optimal signal and contrast for different sample types are discussed. • Effects of dwell time during EDX acquisition are discussed.

Panorama 2011: Refining: varying conditions by region

International Nuclear Information System (INIS)

Silva, C.

2011-01-01

The economic crisis has further weakened a sector that was already facing difficulties, if we look beyond the flush period (2005-2008) when, buoyed by strong demand, margins remained high and refiners could generate profits while maintaining a healthy level of activity. Falling demand and increased over-capacity in some regions - the immediate consequences of the deteriorating economic conditions over the past two years - have led to declining margins and to financial accounts being in the red. The adoption of increasingly stringent emissions standards and product specifications, burdensome regulatory requirements for refineries (for combating local pollution and reducing greenhouse gas emissions), stiffer competition from new fuels: all of these structural factors are weakening the sector, especially in industrialized nations with their more rigorous regulatory compliance. In this generally gloomy climate, numerous new projects are still being envisaged - although many have recently been postponed and tend to be concentrated in developing countries. (author)

Review of experimental data for modelling LWR fuel cladding behaviour under loss of coolant accident conditions

Energy Technology Data Exchange (ETDEWEB)

Massih, Ali R. [Quantum Technologies AB, Uppsala Science Park (Sweden)

2007-02-15

Extensive range of experiments has been conducted in the past to quantitatively identify and understand the behaviour of fuel rod under loss-of-coolant accident (LOCA) conditions in light water reactors (LWRs). The obtained experimental data provide the basis for the current emergency core cooling system acceptance criteria under LOCA conditions for LWRs. The results of recent experiments indicate that the cladding alloy composition and high burnup effects influence LOCA acceptance criteria margins. In this report, we review some past important and recent experimental results. We first discuss the background to acceptance criteria for LOCA, namely, clad embrittlement phenomenology, clad embrittlement criteria (limitations on maximum clad oxidation and peak clad temperature) and the experimental bases for the criteria. Two broad kinds of test have been carried out under LOCA conditions: (i) Separate effect tests to study clad oxidation, clad deformation and rupture, and zirconium alloy allotropic phase transition during LOCA. (ii) Integral LOCA tests, in which the entire LOCA sequence is simulated on a single rod or a multi-rod array in a fuel bundle, in laboratory or in a tests and results are discussed and empirical correlations deduced from these tests and quantitative models are conferred. In particular, the impact of niobium in zirconium base clad and hydrogen content of the clad on allotropic phase transformation during LOCA and also the burst stress are discussed. We review some recent LOCA integral test results with emphasis on thermal shock tests. Finally, suggestions for modelling and further evaluation of certain experimental results are made.

Optimisation of Experimental Conditions for Ex-Bed Desulfurization

Energy Technology Data Exchange (ETDEWEB)

Sanchez, J. M.; Ruiz, E.; Otero, J.

2010-12-22

This report compiles the results of the work conducted by CIEMAT for Task 6.3 Sulfur and Nitrogen Compounds Abatement of the FLEXGAS project Near Zero Emission Advanced Fluidized Bed Gasification, which has been carried out with financial support from the Research Fund for Coal and Steel, RFCR-CT-2007-00005. The assignment of CIEMAT in Task 6.3 has dealt with the experimental study of ex-bed desulfurization at high temperature and high pressure. Based on a review of the state of the art, a zinc oxide sorbent was chosen as a promising candidate for bulk sulfur removal in highly reducing gases such as those from coal and waste oxygen gasification or for a polishing stage in low sulfur content gases, which is typically the case in biomass gasification gases. The work accomplished has included the study of the sulfidation and regeneration stages in order to determine successful operating conditions and the assessment of the long term performance of the sorbent over subsequent sulfidation and regeneration cycles. (Author) 36 refs.

Anistropically varying conductivity in irreversible electroporation simulations.

Science.gov (United States)

Labarbera, Nicholas; Drapaca, Corina

2017-11-01

One recent area of cancer research is irreversible electroporation (IRE). Irreversible electroporation is a minimally invasive procedure where needle electrodes are inserted into the body to ablate tumor cells with electricity. The aim of this paper is to propose a mathematical model that incorporates a tissue's conductivity increasing more in the direction of the electrical field as this has been shown to occur in experiments. It was necessary to mathematically derive a valid form of the conductivity tensor such that it is dependent on the electrical field direction and can be easily implemented into numerical software. The derivation of a conductivity tensor that can take arbitrary functions for the conductivity in the directions tangent and normal to the electrical field is the main contribution of this paper. Numerical simulations were performed for isotropic-varying and anisotropic-varying conductivities to evaluate the importance of including the electrical field's direction in the formulation for conductivity. By starting from previously published experimental results, this paper derived a general formulation for an anistropic-varying tensor for implementation into irreversible electroporation modeling software. The anistropic-varying tensor formulation allows the conductivity to take into consideration both electrical field direction and magnitude, as opposed to previous published works that only took into account electrical field magnitude. The anisotropic formulation predicts roughly a five percent decrease in ablation size for the monopolar simulation and approximately a ten percent decrease in ablation size for the bipolar simulations. This is a positive result as previously reported results found the isotropic formulation to overpredict ablation size for both monopolar and bipolar simulations. Furthermore, it was also reported that the isotropic formulation overpredicts the ablation size more for the bipolar case than the monopolar case. Thus, our

Experimental Study on Intelligent Control Scheme for Fan Coil Air-Conditioning System

Directory of Open Access Journals (Sweden)

Yanfeng Li

2013-01-01

Full Text Available An intelligent control scheme for fan coil air-conditioning systems has been put forward in order to overcome the shortcomings of the traditional proportion-integral-derivative (PID control scheme. These shortcomings include the inability of anti-interference and large inertia. An intelligent control test rig of fan coil air-conditioning system has been built, and MATLAB/Simulink dynamics simulation software has been adopted to implement the intelligent control scheme. A software for data exchange has been developed to combine the intelligence control system and the building automation (BA system. Experimental tests have been conducted to investigate the effectiveness of different control schemes including the traditional PID control, fuzzy control, and fuzzy-PID control for fan coil air-conditioning system. The effects of control schemes have been compared and analyzed in robustness, static and dynamic character, and economy. The results have shown that the developed data exchange interface software can induce the intelligent control scheme of the BA system more effectively. Among the proposed control strategies, fuzzy-PID control scheme which has the advantages of both traditional PID and fuzzy schemes is the optimal control scheme for the fan coil air-conditioning system.

Synthesis of different-sized silver nanoparticles by simply varying reaction conditions with leaf extracts of Bauhinia variegata L.

Science.gov (United States)

Kumar, V; Yadav, S K

2012-03-01

Green synthesis of nanoparticles is one of the crucial requirements in today's climate change scenario all over the world. In view of this, leaf extract (LE) of Bauhinia variegata L. possessing strong antidiabetic and antibacterial properties has been used to synthesise silver nanoparticles (SNP) in a controlled manner. Various-sized SNP (20-120 nm) were synthesised by varying incubation temperature, silver nitrate and LE concentrations. The rate of SNP synthesis and their size increased with increase in AgNO(3) concentration up to 4 mM. With increase in LE concentration, size and aggregation of SNP was increased. The size and aggregation of SNP were also increased at temperatures above and below 40°C. This has suggested that size and dispersion of SNP can be controlled by varying reaction components and conditions. Polarity-based fractionation of B. variegata LE has suggested that only water-soluble fraction is responsible for SNP synthesis. Fourier transform infrared spectroscopy analysis revealed the attachment of polyphenolic and carbohydrate moieties to SNP. The synthesised SNPs were found stable in double distilled water, BSA and phosphate buffer (pH 7.4). On the contrary, incubation of SNP with NaCl induced aggregation. This suggests the safe use of SNP for various in vivo applications.

Deep Boreholes Seals Subjected to High P, T conditions – Preliminary Experimental Studies

Energy Technology Data Exchange (ETDEWEB)

Caporuscio, Florie Andre [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Norskog, Katherine Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Maner, James Lavada [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-01-18

The objective of this planned experimental work is to evaluate physio-chemical processes for ‘seal’ components and materials relevant to deep borehole disposal. These evaluations will encompass multi-laboratory efforts for the development of seals concepts and application of Thermal-Mechanical-Chemical (TMC) modeling work to assess barrier material interactions with subsurface fluids, their stability at high temperatures, and the implications of these processes to the evaluation of thermal limits. Deep borehole experimental work will constrain the Pressure, Temperature (P, T) conditions which “seal” material will experience in deep borehole crystalline rock repositories. The rocks of interest to this study include the silicic (granitic gneiss) end members. The experiments will systematically add components to capture discrete changes in both water and EBS component chemistries.

Assessing the effects of adaptation measures on optimal water resources allocation under varied water availability conditions

Science.gov (United States)

Liu, Dedi; Guo, Shenglian; Shao, Quanxi; Liu, Pan; Xiong, Lihua; Wang, Le; Hong, Xingjun; Xu, Yao; Wang, Zhaoli

2018-01-01

Human activities and climate change have altered the spatial and temporal distribution of water availability which is a principal prerequisite for allocation of different water resources. In order to quantify the impacts of climate change and human activities on water availability and optimal allocation of water resources, hydrological models and optimal water resource allocation models should be integrated. Given that increasing human water demand and varying water availability conditions necessitate adaptation measures, we propose a framework to assess the effects of these measures on optimal allocation of water resources. The proposed model and framework were applied to a case study of the middle and lower reaches of the Hanjiang River Basin in China. Two representative concentration pathway (RCP) scenarios (RCP2.6 and RCP4.5) were employed to project future climate, and the Variable Infiltration Capacity (VIC) hydrological model was used to simulate the variability of flows under historical (1956-2011) and future (2012-2099) conditions. The water availability determined by simulating flow with the VIC hydrological model was used to establish the optimal water resources allocation model. The allocation results were derived under an extremely dry year (with an annual average water flow frequency of 95%), a very dry year (with an annual average water flow frequency of 90%), a dry year (with an annual average water flow frequency of 75%), and a normal year (with an annual average water flow frequency of 50%) during historical and future periods. The results show that the total available water resources in the study area and the inflow of the Danjiangkou Reservoir will increase in the future. However, the uneven distribution of water availability will cause water shortage problems, especially in the boundary areas. The effects of adaptation measures, including water saving, and dynamic control of flood limiting water levels (FLWLs) for reservoir operation, were

Curing potential of experimental resin composites with systematically varying amount of bioactive glass: Degree of conversion, light transmittance and depth of cure.

Science.gov (United States)

Par, Matej; Spanovic, Nika; Bjelovucic, Ruza; Skenderovic, Hrvoje; Gamulin, Ozren; Tarle, Zrinka

2018-06-17

The aim of this work was to investigate the curing potential of an experimental resin composite series with the systematically varying amount of bioactive glass 45S5 by evaluating the degree of conversion, light transmittance and depth of cure. Resin composites based on a Bis-GMA/TEGDMA resin with a total filler load of 70 wt% and a variable amount of bioactive glass (0-40 wt%) were prepared. The photoinitiator system was camphorquinone and ethyl-4-(dimethylamino) benzoate. The degree of conversion and light transmittance were measured by Raman spectroscopy and UV-vis spectroscopy, respectively. The depth of cure was evaluated according to the classical ISO 4049 test. The initial introduction of bioactive glass into the experimental series diminished the light transmittance while the further increase in the bioactive glass amount up to 40 wt% caused minor variations with no clear trend. The curing potential of the experimental composites was similar to or better than that of commercial resin composites. However, unsilanized bioactive glass fillers demonstrated the tendency to diminish both the maximum attainable conversion and the curing efficiency at depth. Experimental composite materials containing bioactive glass showed a clinically acceptable degree of conversion and depth of cure. The degree of conversion and depth of cure were diminished by bioactive glass fillers in a dose-dependent manner, although light transmittance was similar among all of the experimental composites containing 5-40 wt% of bioactive glass. Reduced curing potential caused by the bioactive glass has possible consequences on mechanical properties and biocompatibility. Copyright © 2018 Elsevier Ltd. All rights reserved.

Separating timing, movement conditions and individual differences in the analysis of human movement

DEFF Research Database (Denmark)

Raket, Lars Lau; Grimme, Britta; Schöner, Gregor

2016-01-01

mixed-effects models as viable alternatives to conventional analysis frameworks. The model is then combined with a novel factor-analysis model that estimates the low-dimensional subspace within which movements vary when the task demands vary. Our framework enables us to visualize different dimensions......A central task in the analysis of human movement behavior is to determine systematic patterns and differences across experimental conditions, participants and repetitions. This is possible because human movement is highly regular, being constrained by invariance principles. Movement timing...

Experimental study on centerline velocities of a rectangular capture hood under realistic conditions.

Science.gov (United States)

He, Xinjian; Lewis, Braxton V; Guffey, Steven E

2018-02-01

Capture hoods are an important component of a local ventilation system designed to reduce exposures to airborne contaminants. The velocity at any point along the centerline of the hood (V x ) is currently estimated using one of many predictive equations developed since the 1930s. It is unproven that those predictive equations for V x are accurate, despite the prodigious number of studies concerning them. Among other issues, almost all experimental verifications were conducted for conditions that were either unrealistically ideal without competing air currents (e.g., zero cross draft) or were not described. This study measured values of V x along the midline using Particle Image Velocimetry (PIV) at distances of 1-14 inches in front of a rectangular capture hood. The experiments were conducted in a large wind tunnel (9' × 12' × 40', H × W × L) using a heated, breathing, anthropomorphically sized manikin. Three 0 degree draft velocities (V draft = 4, 14, and 50 ft/min) were tested, all directed toward the hood face and the back of the manikin (if present). For each value of V draft , the velocity fields were measured in a factorial design with and without the manikin, and with and without a worktable underneath the hood. An ideal condition was represented by a freestanding hood at the 4 fpm draft. Nonideal conditions included the presence of a worktable or manikin, and the combination of table and manikin. Each condition was tested at the three levels of V draft . The experimental results found significant effects (p < 0.001) for V draft , the presence of the manikin, the presence of the worktable, and all combinations of those factors. The effects of the independent variables were most pronounced at distances greater than 10 in (25.4 cm) from the hood face. It is concluded that none of the previously published models accurately predicted V x under the realistic conditions tested in this study. A satisfactory model will have to include terms for V draft and the

Ellipsometry with randomly varying polarization states

NARCIS (Netherlands)

Liu, F.; Lee, C. J.; Chen, J. Q.; E. Louis,; van der Slot, P. J. M.; Boller, K. J.; F. Bijkerk,

2012-01-01

We show that, under the right conditions, one can make highly accurate polarization-based measurements without knowing the absolute polarization state of the probing light field. It is shown that light, passed through a randomly varying birefringent material has a well-defined orbit on the Poincar

Optimization of experimental conditions in uranium trace determination using laser time-resolved fluorimetry

International Nuclear Information System (INIS)

Baly, L.; Garcia, M.A.

1996-01-01

At the present paper a new sample excitation geometry is presented for the uranium trace determination in aqueous solutions by the Time-Resolved Laser-Induced Fluorescence. This new design introduces the laser radiation through the top side of the cell allowing the use of cells with two quartz sides, less expensive than commonly used at this experimental set. Optimization of the excitation conditions, temporal discrimination and spectral selection are presented

Pre-Swirl Stator and Propeller Design for Varying Operating Conditions

DEFF Research Database (Denmark)

Saettone, Simone; Regener, Pelle Bo; Andersen, Poul

2016-01-01

blades ahead of the propeller.This paper describes the hydrodynamic design of apre-swirl stator with radially variable pitch, paired with aconventional propeller. The aim is to achieve the highest possible effciency in various operating conditions, and to avoid effciency penalties in off-design operation.......To investigate the propeller and stator designs and configurations in different operating conditions, the computationally inexpensive vortex-lattice method is used a sa first step to optimize the geometry in an initial parameter study. Then the flow over hull, stator and propelleris simulated in a CFD...

Effect of Varying Acid Hydrolysis Condition in Gracilaria Sp. Fermentation Using Sasad

Science.gov (United States)

Mansuit, H.; Samsuri, M. D. C.; Sipaut, C. S.; Yee, C. F.; Yasir, S. M.; Mansa, R.

2015-04-01

Macroalgae or seaweed is being considered as promising feedstock for bioalcohol production due to high polysaccharides content. Polysaccharides can be converted into fermentable sugar through acid hydrolysis pre-treatment. In this study, the potential of using carbohydrate-rich macroalgae, Gracilaria sp. as feedstock for bioalcohol production via various acid hydrolysis conditions prior to the fermentation process was investigated and evaluated. The seaweed used in this research was from the red algae group, using species of Gracilaria sp. which was collected from Sg. Petani Kedah, Malaysia. Pre-treatment of substrate was done using H2SO4 and HCl with molarity ranging from 0.2M to 0.8M. The pretreatment time were varied in the range of 15 to 30 minutes. Fermentation was conducted using Sasad, a local Sabahan fermentation agent as a starter culture. Alcohol extraction was done using a distillation unit. Reducing sugar analysis was done by Benedict test method. Alcohol content analysis was done using specific gravity test. After hydrolysis, it was found out that acid hydrolysis at 0.2M H2SO4 and pre-treated for 20 minutes at 121°C has shown the highest reducing sugar content which has yield (10.06 mg/g) of reducing sugar. It was followed by other samples hydrolysis using 0.4M HCl with 30 minutes pre-treatment and 0.2M H2SO4, 15 minutes pre-treatment with yield of 8.06 mg/g and 5.75 mg/g reducing sugar content respectively. In conclusion, acid hydrolysis of Gracilaria sp. can produce higher reducing sugar yield and thus it can further enhance the bioalcohol production yield. Hence, acid hydrolysis of Gracilaria sp. should be studied more as it is an important step in the bioalcohol production and upscaling process.

What causes IOR? Attention or perception? - manipulating cue and target luminance in either blocked or mixed condition.

Science.gov (United States)

Zhao, Yuanyuan; Heinke, Dietmar

2014-12-01

Inhibition of return (IOR) refers to the performance disadvantage when detecting a target presented at a previously cued location. The current paper contributes to the long-standing debate whether IOR is caused by attentional processing or perceptual processing. We present a series of four experiments which varied the cue luminance in mixed and blocked conditions. We hypothesised that if inhibition was initialized by an attentional process the size of IOR should not vary in the blocked condition as participants should be able to adapt to the level of cue luminance. However, if a perceptual process triggers inhibition both experimental manipulations should lead to varying levels of IOR. Indeed, we found evidence for the latter hypothesis. In addition, we also varied the target luminance in blocked and mixed condition. Both manipulations, cue luminance and target luminance, affected IOR in an additive fashion suggesting that the two stimuli affect human behaviour on different processing stages. Copyright © 2014 Elsevier Ltd. All rights reserved.

Automatic Traffic Data Collection under Varying Lighting and Temperature Conditions in Multimodal Environments: Thermal versus Visible Spectrum Video-Based Systems

Directory of Open Access Journals (Sweden)

Ting Fu

2017-01-01

Full Text Available Vision-based monitoring systems using visible spectrum (regular video cameras can complement or substitute conventional sensors and provide rich positional and classification data. Although new camera technologies, including thermal video sensors, may improve the performance of digital video-based sensors, their performance under various conditions has rarely been evaluated at multimodal facilities. The purpose of this research is to integrate existing computer vision methods for automated data collection and evaluate the detection, classification, and speed measurement performance of thermal video sensors under varying lighting and temperature conditions. Thermal and regular video data was collected simultaneously under different conditions across multiple sites. Although the regular video sensor narrowly outperformed the thermal sensor during daytime, the performance of the thermal sensor is significantly better for low visibility and shadow conditions, particularly for pedestrians and cyclists. Retraining the algorithm on thermal data yielded an improvement in the global accuracy of 48%. Thermal speed measurements were consistently more accurate than for the regular video at daytime and nighttime. Thermal video is insensitive to lighting interference and pavement temperature, solves issues associated with visible light cameras for traffic data collection, and offers other benefits such as privacy, insensitivity to glare, storage space, and lower processing requirements.

Experimental Assessment of residential split type air-conditioning systems using alternative refrigerants to R-22 at high ambient temperatures

International Nuclear Information System (INIS)

Joudi, Khalid A.; Al-Amir, Qusay R.

2014-01-01

Highlights: • R290, R407C and R410A in residential split A/C units at high ambient. • 1 and 2 TR residential air conditioners with R22 alternatives at high ambient. • Residential split unit performance at ambients up to 55 °C with R22 alternatives. - Abstract: Steady state performance of residential air conditioning systems using R22 and alternatives R290, R407C, R410A, at high ambient temperatures, have been investigated experimentally. System performance parameters such as optimum refrigerant charge, coefficient of performance, cooling capacity, power consumption, pressure ratio, power per ton of refrigeration and TEWI environmental factor have been determined. All refrigerants were tested in the cooling mode operation under high ambient air temperatures, up to 55 °C, to determine their suitability. Two split type air conditioner of 1 and 2 TR capacities were used. A psychrometric test facility was constructed consisting of a conditioned cool compartment and an environmental duct serving the condenser. Air inside the conditioned compartment was maintained at 25 °C dry bulb and 19 °C wet bulb for all tests. In the environmental duct, the ambient air temperature was varied from 35 °C to 55 °C in 5 °C increments. The study showed that R290 is the better candidate to replace R22 under high ambient air temperatures. It has lower TEWI values and a better coefficient of performance than the other refrigerants tested. It is suitable as a drop-in refrigerant. R407C has the closest performance to R22, followed by R410A

Steady shear viscosity of stirred yoghurts with varying ropiness

NARCIS (Netherlands)

van Marle, M.E.; van Marle, M.E.; van den Ende, Henricus T.M.; de Kruif, C.G.; de Kruif, C.G.; Mellema, J.

1999-01-01

Stirred yogurt was viewed as a concentrated dispersion of aggregates consisting of protein particles. The steady-shear behavior of three types of stirred yogurt with varying ropiness was investigated experimentally. To describe the shear-dependent viscosity, a microrheological model was used which

PERT: A Method for Expression Deconvolution of Human Blood Samples from Varied Microenvironmental and Developmental Conditions

Science.gov (United States)

Csaszar, Elizabeth; Yu, Mei; Morris, Quaid; Zandstra, Peter W.

2012-01-01

The cellular composition of heterogeneous samples can be predicted using an expression deconvolution algorithm to decompose their gene expression profiles based on pre-defined, reference gene expression profiles of the constituent populations in these samples. However, the expression profiles of the actual constituent populations are often perturbed from those of the reference profiles due to gene expression changes in cells associated with microenvironmental or developmental effects. Existing deconvolution algorithms do not account for these changes and give incorrect results when benchmarked against those measured by well-established flow cytometry, even after batch correction was applied. We introduce PERT, a new probabilistic expression deconvolution method that detects and accounts for a shared, multiplicative perturbation in the reference profiles when performing expression deconvolution. We applied PERT and three other state-of-the-art expression deconvolution methods to predict cell frequencies within heterogeneous human blood samples that were collected under several conditions (uncultured mono-nucleated and lineage-depleted cells, and culture-derived lineage-depleted cells). Only PERT's predicted proportions of the constituent populations matched those assigned by flow cytometry. Genes associated with cell cycle processes were highly enriched among those with the largest predicted expression changes between the cultured and uncultured conditions. We anticipate that PERT will be widely applicable to expression deconvolution strategies that use profiles from reference populations that vary from the corresponding constituent populations in cellular state but not cellular phenotypic identity. PMID:23284283

Global stabilization of linear continuous time-varying systems with bounded controls

International Nuclear Information System (INIS)

Phat, V.N.

2004-08-01

This paper deals with the problem of global stabilization of a class of linear continuous time-varying systems with bounded controls. Based on the controllability of the nominal system, a sufficient condition for the global stabilizability is proposed without solving any Riccati differential equation. Moreover, we give sufficient conditions for the robust stabilizability of perturbation/uncertain linear time-varying systems with bounded controls. (author)

Scram reliability under seismic conditions at the Experimental Breeder Reactor II

International Nuclear Information System (INIS)

Roglans, J.; Wang, C.Y.; Hill, D.J.

1993-01-01

A Probabilistic Risk Assessment of the Experimental Breeder Reactor II has recently been completed. Seismic events are among the external initiating events included in the assessment. As part of the seismic PRA a detailed study has been performed of the ability to shutdown the reactor under seismic conditions. A comprehensive finite element model of the EBR-II control rod drive system has been used to analyze the control rod system response when subjected to input seismic accelerators. The results indicate the control rod drive system has a high seismic capacity. The estimated seismic fragility for the overall reactor shutdown system is dominated by the primary tank failure

The effect of process conditions on the alpha-amylolytic hydrolysis of amylopectin potato starch : an experimental design approach

NARCIS (Netherlands)

Marchal, L.M.; Jonkers, J.; Franke, G.T.; Goooijer, de C.D.; Tramper, J.

1999-01-01

The hydrolysis of amylopectin potato starch with Bacillus licheniformis α-amylase (Maxamyl) was studied under industrially relevant conditions (i.e. high dry-weight concentrations). The following ranges of process conditions were chosen and investigated by means of an experimental design: pH [5.6-

Experimental study of movements respiratory conditions acceptable in radiotherapy techniques advanced; Estudio experimental de las condiciones de movimiento respiratorio aceptables en tecnicas de radioterapia avanzada

Energy Technology Data Exchange (ETDEWEB)

Carrasco de Fez, P.; Ruiz Martinez, A.; Ruiz Martinez, A.; Jornet Sala, N.; Latorre Musoll, A.; Eudaldo Puell, T.; Ribas Morales, M.

2015-07-01

The aim is Determine experimentally in what conditions the movement of the PTV produces uncertainties unacceptable in the various stages of the treatment radiotherapy, from the acquisition of imagens 4D to the irradiation. (Author)

Experimental investigations on a common centrifugal pump operating under gas entrainment conditions

Energy Technology Data Exchange (ETDEWEB)

Schäfer, Thomas, E-mail: thomas.schaefer@hzdr.de [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Fluid Dynamics (Germany); Neumann, Martin [Technische Universität Dresden, AREVA Endowed Chair of Imaging Techniques in Energy and Process Engineering (Germany); Bieberle, André [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Fluid Dynamics (Germany); Hampel, Uwe [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Fluid Dynamics (Germany); Technische Universität Dresden, AREVA Endowed Chair of Imaging Techniques in Energy and Process Engineering (Germany)

2017-05-15

Highlights: • The pump performance has been evaluated for several gas entrainment conditions. • The gas entraining flow regime has a large impact on the pump performance. • High-resolution gamma-ray computed tomography (HireCT) has been applied. • Gas holdup inside the operating impeller has been visualized and quantified. • Gas holdup profiles along selected streamlines have been calculated. - Abstract: This paper presents an experimental study on the effects of additional gas entrainment in centrifugal pumps designed for conveying liquid phases only. The pump performance has been evaluated for several gas entrainment conditions, and for various operational settings of the pump, such as its alignment and the rotational speed of the impeller. As a main performance indicator the impact of entrained gas on the hydraulic power of the pump has been analyzed using experimental data. Additionally, high-resolution gamma-ray computed tomography (HireCT) operated in time-averaged rotation-synchronized scanning mode has been applied to quantify local phase fraction distributions inside the rapidly rotating pump impeller. Based on these quantitative tomographic measurements, gas holdup profiles along selected streamlines have been calculated and gas accumulation areas inside the impeller chambers have been visualized. Thus, various internally accumulated gas holdup patterns have been identified and, eventually, associated with characteristic pump performance behaviors. Moreover, the tomographic measuring method allowed an enhanced gas holdup analysis in specified pump compartments. As a result, the related specific gas and liquid phase holdup profiles have been evaluated.

Experimental investigations on a common centrifugal pump operating under gas entrainment conditions

International Nuclear Information System (INIS)

Schäfer, Thomas; Neumann, Martin; Bieberle, André; Hampel, Uwe

2017-01-01

Highlights: • The pump performance has been evaluated for several gas entrainment conditions. • The gas entraining flow regime has a large impact on the pump performance. • High-resolution gamma-ray computed tomography (HireCT) has been applied. • Gas holdup inside the operating impeller has been visualized and quantified. • Gas holdup profiles along selected streamlines have been calculated. - Abstract: This paper presents an experimental study on the effects of additional gas entrainment in centrifugal pumps designed for conveying liquid phases only. The pump performance has been evaluated for several gas entrainment conditions, and for various operational settings of the pump, such as its alignment and the rotational speed of the impeller. As a main performance indicator the impact of entrained gas on the hydraulic power of the pump has been analyzed using experimental data. Additionally, high-resolution gamma-ray computed tomography (HireCT) operated in time-averaged rotation-synchronized scanning mode has been applied to quantify local phase fraction distributions inside the rapidly rotating pump impeller. Based on these quantitative tomographic measurements, gas holdup profiles along selected streamlines have been calculated and gas accumulation areas inside the impeller chambers have been visualized. Thus, various internally accumulated gas holdup patterns have been identified and, eventually, associated with characteristic pump performance behaviors. Moreover, the tomographic measuring method allowed an enhanced gas holdup analysis in specified pump compartments. As a result, the related specific gas and liquid phase holdup profiles have been evaluated.

Verification of Dinamika-5 code on experimental data of water level behaviour in PGV-440 under dynamic conditions

Energy Technology Data Exchange (ETDEWEB)

Beljaev, Y.V.; Zaitsev, S.I.; Tarankov, G.A. [OKB Gidropress (Russian Federation)

1995-12-31

Comparison of the results of calculational analysis with experimental data on water level behaviour in horizontal steam generator (PGV-440) under the conditions with cessation of feedwater supply is presented in the report. Calculational analysis is performed using DIMANIKA-5 code, experimental data are obtained at Kola NPP-4. (orig.). 2 refs.

Verification of Dinamika-5 code on experimental data of water level behaviour in PGV-440 under dynamic conditions

Energy Technology Data Exchange (ETDEWEB)

Beljaev, Y V; Zaitsev, S I; Tarankov, G A [OKB Gidropress (Russian Federation)

1996-12-31

Comparison of the results of calculational analysis with experimental data on water level behaviour in horizontal steam generator (PGV-440) under the conditions with cessation of feedwater supply is presented in the report. Calculational analysis is performed using DIMANIKA-5 code, experimental data are obtained at Kola NPP-4. (orig.). 2 refs.

Enhancement of heat transfer using varying width twisted tape inserts

African Journals Online (AJOL)

International Journal of Engineering, Science and Technology ... experimental investigations of the augmentation of turbulent flow heat transfer in a horizontal tube by means of varying width twisted tape inserts with air as the working fluid.

Experimental characterization of a concentrating photovoltaic system varying the light concentration

International Nuclear Information System (INIS)

Renno, C.; Petito, F.; Landi, G.; Neitzert, H.C.

2017-01-01

Highlights: • Experimental characterization of a concentrating photovoltaic system. • Analysis of the point-focus concentrating system performances. • Photovoltaic system parameters as function of the concentration factor. - Abstract: The concentrating photovoltaic system represents one of the most promising solar technologies because it allows a more efficient energy conversion. When a CPV system is designed, the main parameter which has to be considered is the concentration factor that affects both the system energy performances and its configuration. An experimental characterization of a CPV system previously realized at the University of Salerno, is presented in this paper considering several aspects related to the optical configuration, the concentration factor and the solar cell used. In particular, the parameters of an Indium Gallium Phosphide/Gallium Arsenide/Germanium triple-junction solar cell are investigated as function of the concentration factor determined by means of an experimental procedure that uses different optical configurations. The maximum concentration factor reached by the CPV system is 310 suns. The cell parameters dependence on the concentration is reported together with an electroluminescence analysis of the Indium Gallium Phosphide/Gallium Arsenide/Germanium cell. A monitoring of the electrical power provided by the system during its working is also presented corresponding to different direct irradiance values. A mean power of 2.95 W with an average efficiency of 32.8% is obtained referring to a mean irradiance of 930 W/m"2; lower values are obtained when the irradiance is highly fluctuating. The concentrating photovoltaic system electric energy output is estimated considering different concentration levels; the maximal obtained value is 23.5 W h on a sunny day at 310×. Finally, the temperature of the triple-junction solar cell is evaluated for different months in order to evaluate the potential annual thermal energy production

Experimental Investigation into Suitable Process Conditions for Plastic Injection Molding of Thin-Sheet Parts

Directory of Open Access Journals (Sweden)

Dyi-Cheng Chen

2014-04-01

Full Text Available This study performs an experimental investigation into the effects of the process parameters on the surface quality of injection molded thin-sheet thermoplastic components. The investigations focus specifically on the shape, number and position of the mold gates, the injection pressure and the injection rate. It can be seen that the gravity force entering point improved filling of the cavity for the same forming time and injection pressure. Moreover, it shows the same injection pressure and packing time, the taper-shape gate yields a better surface appearance than the sheet-shape gate. The experimental results provide a useful source of reference in suitable the process conditions for the injection molding of thin-sheet plastic components.

Experimental analysis of fuzzy controlled energy efficient demand controlled ventilation economizer cycle variable air volume air conditioning system

Directory of Open Access Journals (Sweden)

Rajagopalan Parameshwaran

2008-01-01

Full Text Available In the quest for energy conservative building design, there is now a great opportunity for a flexible and sophisticated air conditioning system capable of addressing better thermal comfort, indoor air quality, and energy efficiency, that are strongly desired. The variable refrigerant volume air conditioning system provides considerable energy savings, cost effectiveness and reduced space requirements. Applications of intelligent control like fuzzy logic controller, especially adapted to variable air volume air conditioning systems, have drawn more interest in recent years than classical control systems. An experimental analysis was performed to investigate the inherent operational characteristics of the combined variable refrigerant volume and variable air volume air conditioning systems under fixed ventilation, demand controlled ventilation, and combined demand controlled ventilation and economizer cycle techniques for two seasonal conditions. The test results of the variable refrigerant volume and variable air volume air conditioning system for each techniques are presented. The test results infer that the system controlled by fuzzy logic methodology and operated under the CO2 based mechanical ventilation scheme, effectively yields 37% and 56% per day of average energy-saving in summer and winter conditions, respectively. Based on the experimental results, the fuzzy based combined system can be considered to be an alternative energy efficient air conditioning scheme, having significant energy-saving potential compared to the conventional constant air volume air conditioning system.

Experimental and FE Analysis of Exterior Plastic Components of Cars under Static and Dynamic Loading Conditions

OpenAIRE

Faghihi, Hassan

2011-01-01

This thesis is composed by an experimental part and numerical part, aimed at contributing to a better knowledge of the behavior of plastic parts under different loading conditions. The study is intended to validate a FE model for simulating exterior plastic components of car especially the A-decor and plastic clips in the context of thermal and static load analysis. From the comparison of numerical and experimental results in the terms of thermal and static deformation of the A-decor, it is c...

Influence of Experimental Conditions on Electronic Tongue Results—Case of Valsartan Minitablets Dissolution

Directory of Open Access Journals (Sweden)

Małgorzata Wesoły

2016-08-01

Full Text Available A potentiometric electronic tongue was applied to study the release of valsartan from pharmaceutical formulations, i.e., minitablets uncoated and coated with Eudragit E. Special attention was paid to evaluate the influence of medium temperature and composition, as well as to compare the performances of the sensor arrays working in various hydrodynamic conditions. The drug dissolution profiles registered with the ion-sensitive electrodes were compared with standard dissolution tests performed with USP Apparatus 2 (paddle. Moreover, the signal changes of all sensors were processed by principal component analysis to visualize the release modifications, related to the presence of the coating agent. Finally, the importance and influence of the experimental conditions on the results obtained using potentiometric sensor arrays were discussed.

Experimental verification of electrostatic boundary conditions in gate-patterned quantum devices

Science.gov (United States)

Hou, H.; Chung, Y.; Rughoobur, G.; Hsiao, T. K.; Nasir, A.; Flewitt, A. J.; Griffiths, J. P.; Farrer, I.; Ritchie, D. A.; Ford, C. J. B.

2018-06-01

In a model of a gate-patterned quantum device, it is important to choose the correct electrostatic boundary conditions (BCs) in order to match experiment. In this study, we model gated-patterned devices in doped and undoped GaAs heterostructures for a variety of BCs. The best match is obtained for an unconstrained surface between the gates, with a dielectric region above it and a frozen layer of surface charge, together with a very deep back boundary. Experimentally, we find a  ∼0.2 V offset in pinch-off characteristics of 1D channels in a doped heterostructure before and after etching off a ZnO overlayer, as predicted by the model. Also, we observe a clear quantised current driven by a surface acoustic wave through a lateral induced n-i-n junction in an undoped heterostructure. In the model, the ability to pump electrons in this type of device is highly sensitive to the back BC. Using the improved boundary conditions, it is straightforward to model quantum devices quite accurately using standard software.

Optimum condition for spatial ion cyclotron resonance in a multiple magnetic mirror field

International Nuclear Information System (INIS)

Mieno, Tetsu; Hatakeyama, Rikizo; Sato, Noriyoshi

1988-01-01

A Spatial cyclotron resonance of ion beams passing through a multiple magnetic mirror field is investigated experimentally by varying parameters of the multiple mirror field. The optimum resonance condition is realized with a decrease in the cell length of the multiple mirror along the beams to satisfy the local condition of the spatial ion cyclotron resonance. The results show a remarkable increase of nonadiabatic transfer of the beam energy into the transverse direction to the magnetic field. (author)

Design of Multijunction Photovoltaic Cells Optimized for Varied Atmospheric Conditions

Directory of Open Access Journals (Sweden)

C. Zhang

2014-01-01

Full Text Available Band gap engineering provides an opportunity to not only provide higher overall conversion efficiencies of the reference AM1.5 spectra but also customize PV device design for specific geographic locations and microenvironments based on atmospheric conditions characteristic to that particular location. Indium gallium nitride and other PV materials offer the opportunity for limited bandgap engineering to match spectra. The effects of atmospheric conditions such as aerosols, cloud cover, water vapor, and air mass have been shown to cause variations in spectral radiance that alters PV system performance due to both overrating and underrating. Designing PV devices optimized for spectral radiance of a particular region can result in improved PV system performance. This paper presents a new method for designing geographically optimized PV cells with using a numerical model for bandgap optimization. The geographic microclimate spectrally resolved solar flux for twelve representative atmospheric conditions for the incident radiation angle (zenith angle of 48.1° and fixed array angle of 40° is used to iteratively optimize the band gap for tandem, triple, and quad-layer of InGaN-based multijunction cells. The results of this method are illustrated for the case study of solar farms in the New York region and discussed.

Simulation of experiment on aerosol behaviour at severe accident conditions in the LACE experimental facility with the ASTEC CPA code

International Nuclear Information System (INIS)

Kljenak, I.; Mavko, B.

2007-01-01

The experiment LACE LA4 on thermal-hydraulics and aerosol behavior in a nuclear power plant containment, which was performed in the LACE experimental facility, was simulated with the ASTEC CPA module of the severe accident computer code ASTEC V1.2. The specific purpose of the work was to assess the capability of the module (code) to simulate thermal-hydraulic conditions and aerosol behavior in the containment of a light-water-reactor nuclear power plant at severe accident conditions. The test was simulated with boundary conditions, described in the experiment report. Results of thermal-hydraulic conditions in the test vessel, as well as dry aerosol concentrations in the test vessel atmosphere, are compared to experimental results and analyzed. (author)

Adaptive observer-based control for an IPMC actuator under varying humidity conditions

Science.gov (United States)

Bernat, Jakub; Kolota, Jakub

2018-05-01

As ionic polymer metal composites (IPMC) are increasingly applied to mechatronic systems, many new IPMC modeling efforts have been reported in the literature. The demands of rapidly growing technology has generated interest in advancing the intrinsic actuation and sensing capabilities of IPMC. Classical IPMC applications need constant hydration to operate. On the other hand, for IPMCs operating in air, the water content of the polymer varies with the humidity level of the ambient environment, which leads to its strong humidity-dependent behavior. Furthermore, decreasing water content over time plays a crucial role in the effectiveness of IPMC. Therefore, the primary challenge of this work is to accurately model this phenomenon. The principal contribution of the paper is a new IPMC model, which considers the change of moisture content. A novel nonlinear adaptive observer is designed to determine the unknown electric potential and humidity level in the polymer membrane. This approach effectively determines the moisture content of the IPMC during long-term continuous operation in air. This subsequently allows us to develop an effective back-stepping control algorithm that considers varying moisture content. Data from experiments are presented to support the effectiveness of the observation process, which is shown in illustrative examples.

Numerical investigations of rib fracture failure models in different dynamic loading conditions.

Science.gov (United States)

Wang, Fang; Yang, Jikuang; Miller, Karol; Li, Guibing; Joldes, Grand R; Doyle, Barry; Wittek, Adam

2016-01-01

Rib fracture is one of the most common thoracic injuries in vehicle traffic accidents that can result in fatalities associated with seriously injured internal organs. A failure model is critical when modelling rib fracture to predict such injuries. Different rib failure models have been proposed in prediction of thorax injuries. However, the biofidelity of the fracture failure models when varying the loading conditions and the effects of a rib fracture failure model on prediction of thoracic injuries have been studied only to a limited extent. Therefore, this study aimed to investigate the effects of three rib failure models on prediction of thoracic injuries using a previously validated finite element model of the human thorax. The performance and biofidelity of each rib failure model were first evaluated by modelling rib responses to different loading conditions in two experimental configurations: (1) the three-point bending on the specimen taken from rib and (2) the anterior-posterior dynamic loading to an entire bony part of the rib. Furthermore, the simulation of the rib failure behaviour in the frontal impact to an entire thorax was conducted at varying velocities and the effects of the failure models were analysed with respect to the severity of rib cage damages. Simulation results demonstrated that the responses of the thorax model are similar to the general trends of the rib fracture responses reported in the experimental literature. However, they also indicated that the accuracy of the rib fracture prediction using a given failure model varies for different loading conditions.

Cuticular antifungals in spiders: density- and condition dependence.

Directory of Open Access Journals (Sweden)

Daniel González-Tokman

Full Text Available Animals living in groups face a high risk of disease contagion. In many arthropod species, cuticular antimicrobials constitute the first protective barrier that prevents infections. Here we report that group-living spiders produce cuticular chemicals which inhibit fungal growth. Given that cuticular antifungals may be costly to produce, we explored whether they can be modulated according to the risk of contagion (i.e. under high densities. For this purpose, we quantified cuticular antifungal activity in the subsocial crab spider Diaea ergandros in both natural nests and experimentally manipulated nests of varying density. We quantified the body-condition of spiders to test whether antifungal activity is condition dependent, as well as the effect of spider density on body-condition. We predicted cuticular antifungal activity to increase and body-condition to decrease with high spider densities, and that antifungal activity would be inversely related to body-condition. Contrary to our predictions, antifungal activity was neither density- nor condition-dependent. However, body-condition decreased with density in natural nests, but increased in experimental nests. We suggest that pathogen pressure is so important in nature that it maintains high levels of cuticular antifungal activity in spiders, impacting negatively on individual energetic condition. Future studies should identify the chemical structure of the isolated antifungal compounds in order to understand the physiological basis of a trade-off between disease prevention and energetic condition caused by group living, and its consequences in the evolution of sociality in spiders.

Cuticular antifungals in spiders: density- and condition dependence.

Science.gov (United States)

González-Tokman, Daniel; Ruch, Jasmin; Pulpitel, Tamara; Ponton, Fleur

2014-01-01

Animals living in groups face a high risk of disease contagion. In many arthropod species, cuticular antimicrobials constitute the first protective barrier that prevents infections. Here we report that group-living spiders produce cuticular chemicals which inhibit fungal growth. Given that cuticular antifungals may be costly to produce, we explored whether they can be modulated according to the risk of contagion (i.e. under high densities). For this purpose, we quantified cuticular antifungal activity in the subsocial crab spider Diaea ergandros in both natural nests and experimentally manipulated nests of varying density. We quantified the body-condition of spiders to test whether antifungal activity is condition dependent, as well as the effect of spider density on body-condition. We predicted cuticular antifungal activity to increase and body-condition to decrease with high spider densities, and that antifungal activity would be inversely related to body-condition. Contrary to our predictions, antifungal activity was neither density- nor condition-dependent. However, body-condition decreased with density in natural nests, but increased in experimental nests. We suggest that pathogen pressure is so important in nature that it maintains high levels of cuticular antifungal activity in spiders, impacting negatively on individual energetic condition. Future studies should identify the chemical structure of the isolated antifungal compounds in order to understand the physiological basis of a trade-off between disease prevention and energetic condition caused by group living, and its consequences in the evolution of sociality in spiders.

Mechanical Behaviour of Conventional Materials at Experimental Conditions of Deep Drawing Technological Process

Science.gov (United States)

Nikolov, N.; Pashkouleva, D.; Kavardzhikov, V.

2012-09-01

The paper deals with experimental investigations on the mechanical behaviour of body-centred-cubic (BCC) and face-centred-cubic (FCC)-conventionally structured sheet metalic-metalic materials under stress-strain conditions of a deep drawing process determined by a coefficient close to the limiting one for Steel 08 and punch diameter of 50 mm. The mechanical characteristics of the investigated materials are identified by one-dimensional tension tests. The materials' responses, as results of identical loading conditions, are described by the change of blank sizes and characteristics of the forming processes. The chosen deformation path ensures obtaining a qualitative steel piece and leads to failures of aluminium and brass blanks. The reported results could be useful for investigations and predictions of the mechanical responses of such type metallic structures applying microscopic instrumented observations and numerical simulations.

Experimental stress during molt suggests the evolution of condition-dependent and condition-independent ornaments in the king penguin.

Science.gov (United States)

Schull, Quentin; Robin, Jean-Patrice; Dobson, F Stephen; Saadaoui, Hédi; Viblanc, Vincent A; Bize, Pierre

2018-01-01

Sexual selection and social selection are two important theories proposed for explaining the evolution of colorful ornamental traits in animals. Understanding signal honesty requires studying how environmental and physiological factors during development influence the showy nature of sexual and social ornaments. We experimentally manipulated physiological stress and immunity status during the molt in adult king penguins ( Aptenodytes patagonicus ), and studied the consequences of our treatments on colourful ornaments (yellow-orange and UV beak spots and yellow-orange auricular feather patches) known to be used in sexual and social contexts in this species. Whereas some ornamental features showed strong condition-dependence (yellow auricular feather chroma, yellow and UV chroma of the beak), others were condition-independent and remained highly correlated before and after the molt (auricular patch size and beak UV hue). Our study provides a rare examination of the links between ornament determinism and selection processes in the wild. We highlight the coexistence of ornaments costly to produce that may be honest signals used in mate choice, and ornaments for which honesty may be enforced by social mediation or rely on genetic constraints.

Experimental conditions at Osiris with the new CARAMEL fuel

International Nuclear Information System (INIS)

Beylot, J.

1979-01-01

Replacing the former highly enriched (93%) U-Al fuel by low enrichment (7%) oxide has brought about some changes in the experimental conditions for irradiations. The advantages for the experiments placed right in the lattice are shown to be a great improvement in the neutron spectrum (fast/thermal) and a very significant reduction in heating due to gamma radiation. In the case of the peripherally placed experiments there is an increase in the number of high thermal flux sites. In all cases, there is found to be an increase in the duration of the irradiation cycle, between two partial reloadings, permitted by the significant amount of 235 U tied up in the loading. The drawbacks observed are reduced thermo-hydraulic performance of the new fuel elements that does not allow working with a core of a size under a 7x7 configuration, increased surveillance of the kind of experiments placed in the lattice to avoid excessive power rises on the neighbouring fuel elements and moderate reduction in the level of thermal neutron fluxes in the peripheral irradiation sites [fr

Experimental study of the effects of alternating fields on HTS coils according to the winding insulation conditions

International Nuclear Information System (INIS)

Hwang, Y J; Lee, T S; Lee, W S; Ko, T K; Ahn, M C

2013-01-01

This paper examines the effects of alternating fields on high-temperature superconducting (HTS) coils according to the winding insulation condition. Alternating fields can occur in synchronous machines (armature reaction, faults) and other devices. In superconducting synchronous machines, alternating fields affect the operational characteristics of the machine and the superconducting field coil. Therefore, a method of reducing the effects of alternating fields is necessary in superconducting synchronous design. In this study, the effects of alternating fields on the HTS field coil according to the winding insulation condition were experimentally evaluated. The experimental results show that HTS coils made using the no-insulation technique can be a solution for reducing the effects of the alternating field. These results are expected to suggest useful data for applications of HTS field coils in superconducting synchronous machines. (paper)

Differences in nutrient uptake capacity of the benthic filamentous algae Cladophora sp., Klebsormidium sp. and Pseudanabaena sp. under varying N/P conditions.

Science.gov (United States)

Liu, Junzhuo; Vyverman, Wim

2015-03-01

The N/P ratio of wastewater can vary greatly and directly affect algal growth and nutrient removal process. Three benthic filamentous algae species Cladophora sp., Klebsormidium sp. and Pseudanabaena sp. were isolated from a periphyton bioreactor and cultured under laboratory conditions on varying N/P ratios to determine their ability to remove nitrate and phosphorus. The N/P ratio significantly influenced the algal growth and phosphorus uptake process. Appropriate N/P ratios for nitrogen and phosphorus removal were 5-15, 7-10 and 7-20 for Cladophora sp., Klebsormidium sp. and Pseudanabaena sp., respectively. Within these respective ranges, Cladophora sp. had the highest biomass production, while Pseudanabaena sp. had the highest nitrogen and phosphorus contents. This study indicated that Cladophora sp. had a high capacity of removing phosphorus from wastewaters of low N/P ratio, and Pseudanabaena sp. was highly suitable for removing nitrogen from wastewaters with high N/P ratio. Copyright © 2014 Elsevier Ltd. All rights reserved.

Experimental research on single-phase heat transfer characteristics in a vertical circular tube under marine conditions

International Nuclear Information System (INIS)

Du Sijia; Zhang Hong; Jia Baoshan

2011-01-01

Experiments have been conducted to study the heat transfer characteristics of single-phase forced circulation when the test tube was under different marine conditions. The experiments measured the wall temperature of test tube to calculate the heat transfer coefficients at different circumferential places. When the test tube was under inclined conditions, the heat transfer coefficient increased at downside and decreased at upside of test tube because of buoyancy effect. When the test tube was under rolling conditions, the heat transfer coefficients fluctuated with the rolling motions, and the Coriolis force dominated the heat transfer fluctuation during the rolling motion. CFD method was used to simulate the heat transfer phenomena under marine conditions, and the results were accord to the experimental phenomena. (authors)

Experimental investigation on local parameter measurement using optical probes in two-phase flow under rolling condition

International Nuclear Information System (INIS)

Tian Daogui; Sun Licheng; Yan Changqi; Liu Guoqiang

2013-01-01

In order to get more local interfacial information as well as to further comprehend the intrinsic mechanism of two-phase flow under rolling condition, a method was proposed to measure the local parameters by using optical probes under rolling condition in this paper. An experimental investigation of two-phase flow under rolling condition was conducted using the probe fabricated by the authors. It is verified that the probe method is feasible to measure the local parameters in two'-phase flow under rolling condition. The results show that the interfacial parameters distribution near wall region has a distinct periodicity due to the rolling motion. The averaged deviation of the void fraction measured by the probe from that obtained from measured pressure drop is about 8%. (authors)

Echolalic responses by a child with autism to four experimental conditions of sociolinguistic input.

Science.gov (United States)

Violette, J; Swisher, L

1992-02-01

Studies of the immediate verbal imitations (IVIs) of subjects with echolalia report that features of linguistic or social input alone affect the number of IVIs elicited. This experimental study of a child with echolalia and autism controlled each of these variables while introducing a systematic change in the other. The subject produced more (p less than .05) IVIs in response to unknown lexical words presented with a high degree of directiveness (Condition D) than in response to three other conditions of stimulus presentation (e.g., unknown lexical words, minimally directive style.) Thus, an interaction between the effects of linguistic and social input was demonstrated. IVIs were produced across all conditions, primarily during first presentations of lexical stimuli. Only the IVIs elicited by first presentations of the lexical stimuli during Condition D differed significantly (p less than .05) from the number of IVIs elicited by first presentations of lexical stimuli in other conditions. These findings viewed together suggest that the occurrence of IVIs was related, at least for this child, to an uncertain or informative event and that this response was significantly greater when the lexical stimuli were unknown and presented in a highly directive style.

Experimental and numerical investigation on natural convection heat transfer in nanofluids

International Nuclear Information System (INIS)

Kulkarni, P.P.; Nayak, A.K.; Vijayan, P.K.

2014-01-01

Currently, a lot of research is being carried out on the potential application of nanofluids as a coolant in nuclear reactors owing to their enhanced heat transfer characteristics as compared to base fluid. In this regards, an experimental study has been undertaken concerning natural convection heat transfer of nanofluids over a cylindrical heater with a constant wall heat flux condition. The heat flux was varied from 0-50000 W/m 2 and Rayleigh number range is 30000 to 1.65 X 10 5 . Results show that there was a reduction in natural convection heat transfer coefficient of nanofluids as compared to water. Experimental results were compared with existing models for similar geometry. However, the available correlation was found to be unable to predict experimental data. A new empirical model was developed based on the experimental data including the effect of nanoparticles concentration which predicts the experimental data satisfactorily. (author)

Experimental performance study of a proposed desiccant based air conditioning system.

Science.gov (United States)

Bassuoni, M M

2014-01-01

An experimental investigation on the performance of a proposed hybrid desiccant based air conditioning system referred as HDBAC is introduced in this paper. HDBAC is mainly consisted of a liquid desiccant dehumidification unit integrated with a vapor compression system (VCS). The VCS unit has a cooling capacity of 5.27 kW and uses 134a as refrigerant. Calcium chloride (CaCl2) solution is used as the working desiccant material. HDBAC system is used to serve low sensible heat factor applications. The effect of different parameters such as, process air flow rate, desiccant solution flow rate, evaporator box and condenser box solution temperatures, strong solution concentration and regeneration temperature on the performance of the system is studied. The performance of the system is evaluated using some parameters such as: the coefficient of performance (COPa), specific moisture removal and energy saving percentage. A remarkable increase of about 54% in the coefficient of performance of the proposed system over VCS with reheat is achieved. A maximum overall energy saving of about 46% is observed which emphasizes the use of the proposed system as an energy efficient air conditioning system.

Electrothermally Actuated Microbeams With Varying Stiffness

KAUST Repository

Tella, Sherif Adekunle

2017-11-03

We present axially loaded clamped-guided microbeams that can be used as resonators and actuators of variable stiffness, actuation, and anchor conditions. The applied axial load is implemented by U-shaped electrothermal actuators stacked at one of the beams edges. These can be configured and wired in various ways, which serve as mechanical stiffness elements that control the operating resonance frequency of the structures and their static displacement. The experimental results have shown considerable increase in the resonance frequency and mid-point deflection of the microbeam upon changing the end conditions of the beam. These results can be promising for applications requiring large deflection and high frequency tunability, such as filters, memory devices, and switches. The experimental results are compared to multi-physics finite-element simulations showing good agreement among them.

Brane world cosmologies with varying speed of light

International Nuclear Information System (INIS)

Youm, Donam

2001-02-01

We study cosmologies in the Randall-Sundrum models, incorporating the possibility of time-varying speed of light and Newton's constant. The cosmologies with varying speed of light (VSL) were proposed by Moffat and by Albrecht and Magueijo as an alternative to inflation for solving the cosmological problems. We consider the case in which the speed of light varies with time after the radion or the scale of the extra dimension has been stabilized. We elaborate on the conditions under which the flatness problem and the cosmological constant problem can be resolved. Particularly, the VSL cosmologies may provide a possible mechanism for bringing the quantum corrections to the fine-tuned brane tensions after the SUSY breaking under control. (author)

Theoretical and experimental investigations into natural circulation behaviour in a simulated facility of the Indian PHWR under reduced inventory conditions

International Nuclear Information System (INIS)

Satish Kumar, N.V.; Nayak, A.K.; Vijayan, P.K.; Pal, A.K.; Saha, D.; Sinha, R.K.

2004-01-01

A theoretical and experimental investigation has been carried out to study natural circulation characteristics of an Indian PHWR under reduced inventory conditions. The theoretical model incorporates a quasi-steady state analysis of natural circulation at different system inventories. It predicts the system flow rate under single-phase and two-phase conditions and the inventory at which reflux condensation occurs. The model predictions were compared with test data obtained from FISBE (facility for integral system behaviour experiments), which simulates the thermal hydraulic behaviour of the Indian 220 MWe PHWR. The experimental results were found to be in close agreement with the predictions. It was also found that the natural circulation could be oscillatory under reduced inventory conditions. (orig.)

Experimental measurement of compressibility coefficients of synthetic sandstone in hydrostatic conditions

International Nuclear Information System (INIS)

Asaei, H; Moosavi, M

2013-01-01

For the characterization of the mechanical behavior of porous media in elastic conditions, the theory of poroelasticity is used. The number of poroelastic coefficients is greater in elastic conditions because of the complexity of porous media. The laboratory measurement of poroelastic coefficients needs a system that can control and measure the variables of poroelasticity. In this paper, experimental measurements of these coefficients are presented. Laboratory tests are performed using a system designed by the authors. Laboratory hydrostatic tests are performed on cylindrical samples in drained, pore pressure loading, undrained and dry conditions. Compressibilities (bulk and pore compressibility), effective stress and Skempton coefficients are measured by these tests. Samples are made of a composition (sand and cement) and are made by a compaction process synthetically. Calibration tests are performed for the setup to identify possible errors in the system and to correct the results of the main tests. This is done by performing similar compressibility tests at each stress level on a cylindrical steel sample (5.47 mm in diameter) with a longitudinal hole along it (hollow cylinder). A steel sample is used to assume an incompressible sample. The results of the tests are compared with the theory of poroelasticity and the obtained graphs and their errors are analyzed. This study shows that the results of the drained and pore pressure loading tests are compatible with poroelastic formulation, while the undrained results have errors because of extra fluid volume in the pore pressure system and calibration difficulties. (paper)

Experimental Evaluation of Grid Support Enabled PV Inverter Response to Abnormal Grid Conditions: Preprint

Energy Technology Data Exchange (ETDEWEB)

Nelson, Austin; Martin, Gregory; Hurtt, James

2017-05-08

As revised interconnection standards for grid-tied photovoltaic (PV) inverters address new advanced grid support functions (GSFs), there is increasing interest in inverter performance in the case of abnormal grid conditions. The growth of GSF-enabled inverters has outpaced the industry standards that define their operation, although recently published updates to UL1741 with Supplement SA define test conditions for GSFs such as volt-var control, frequency-watt control, and volt-age/frequency ride-through, among others. A comparative experimental evaluation has been completed on four commercially available, three-phase PV inverters in the 24.0-39.8 kVA power range on their GSF capability and the effect on abnormal grid condition response. This study examines the impact particular GSF implementations have on run-on times during islanding conditions, peak voltages in load rejection overvoltage scenarios, and peak currents during single-phase and three-phase fault events for individual inverters. This report reviews comparative test data, which shows that GSFs have little impact on the metrics of interest in most tests cases.

Effects of elevated CO2 and drought on wheat : testing crop simulation models for different experimental and climatic conditions

NARCIS (Netherlands)

Ewert, F.; Rodriguez, D.; Jamieson, P.; Semenov, M.A.; Mitchell, R.A.C.; Goudriaan, J.; Porter, J.R.; Kimball, B.A.; Pinter, P.J.; Manderscheid, R.; Weigel, H.J.; Fangmeier, A.; Fereres, E.; Villalobos, F.

2002-01-01

Effects of increasing carbon dioxide concentration [CO2] on wheat vary depending on water supply and climatic conditions, which are difficult to estimate. Crop simulation models are often used to predict the impact of global atmospheric changes on food production. However, models have rarely been

Experimental study of gas–liquid two-phase flow through packed bed under natural circulation conditions

International Nuclear Information System (INIS)

Chen, Shao-Wen; Miwa, Shuichiro; Griffiths, Matt

2016-01-01

Dry-out phenomena in packed beds or porous media may cause a significant digression of cooling/reaction performance in heat transfer/chemical reactor systems. One of the phenomena responsible for the dry-out in packed beds is known as the counter-current flow limitation (CCFL). In order to investigate the CCFL phenomena induced by gas–liquid two-phase flow in packed beds inside a pool, a natural circulation packed bed test facility was designed and constructed. A total of 27 experimental conditions covering various packing media sizes (sphere diameters: 3.0, 6.4 and 9.5 mm), packed bed heights (15, 35 and 50 cm) and water level heights (1.0, 1.5 and 2.0 m) were tested to examine the CCFL criteria with adiabatic air–water two-phase flow under natural circulation conditions. Both CCFL and flow reversal phenomena were observed, and the experimental data including instantaneous and time-averaged void fraction, differential pressure and superficial gas–liquid velocities were collected. The CCFL criteria were determined when periodical oscillations of void fraction and differential pressure appear. In addition, the Wallis correlation for CCFL was utilized for data analysis, and the Wallis coefficient, C, was determined experimentally from the packed bed CCFL tests. Compared to the existing data-sets in literature, the higher C values obtained in the present experiment suggest a possibly higher dry-out heat flux for natural circulation debris systems, which may be due to the water supply from both top and bottom surfaces of the packed beds. Considering the effects of bed height and hydraulic diameter of the packing media, a newly developed model for the Wallis coefficient, C, under natural circulation CCFL is presented. The present model can predict the experimental data with an averaged absolute error of ±7.9%. (author)

Experimental study of the permeability of concrete under variable thermal and hydric conditions

International Nuclear Information System (INIS)

Chen, W.

2011-01-01

The main objective of this study is to evaluate the variable thermal and hydric effect, with fissuration effect on the hydraulic behaviour of two concretes. Many experimental tests (saturation and permeability measurements, uniaxial and triaxial compressions tests) were carried out in order to investigate the temperature and saturation influence on the behaviour hydraulic on sound and micro-cracked concrete. Moreover, an experimental device for permeability measurement on macro-cracked concrete was realized, it allows to study the behaviour of macro-cracked of concrete confined and subjected to dry gas flow or very moist air at different temperatures. Multiaxial mechanical tests are coupled to the permeability measurements of sound concrete and micro-cracked by freezing and thawing, which allow to measuring the permeability under deviatoric load-unload with the effect of pre-cracking under stress. We also effectuated a test of relative permeability of concrete as a function of water saturation, subjected to drying and re-saturation, conditioning by the different relative humidity imposed. (author)

Forming Limits in Sheet Metal Forming for Non-Proportional Loading Conditions - Experimental and Theoretical Approach

International Nuclear Information System (INIS)

Ofenheimer, Aldo; Buchmayr, Bruno; Kolleck, Ralf; Merklein, Marion

2005-01-01

The influence of strain paths (loading history) on material formability is well known in sheet forming processes. Sophisticated experimental methods are used to determine the entire shape of strain paths of forming limits for aluminum AA6016-T4 alloy. Forming limits for sheet metal in as-received condition as well as for different pre-deformation are presented. A theoretical approach based on Arrieux's intrinsic Forming Limit Stress Curve (FLSC) concept is employed to numerically predict the influence of loading history on forming severity. The detailed experimental strain paths are used in the theoretical study instead of any linear or bilinear simplified loading histories to demonstrate the predictive quality of forming limits in the state of stress

Experimental Investigation of Muon-Catalyzed $dt$ Fusion in Wide Ranges of $D/T$ Mixture Conditions

CERN Document Server

Bom, V R; Demin, D L; van Eijk, C W E; Faifman, M P; Filchenkov, V V; Golubkov, A N; Grafov, N N; Grishenchkin, S K; Gritsaj, K I; Klevtsov, V G; Konin, A D; Kuryakin, A V; Medved', S V; Musyaev, R K; Perevozchikov, V V; Rudenko, A I; Sadetsky, S M; Vinogradov, Yu I; Yukhimchuk, A A; Yukhimchuk, S A; Zinov, V G; Zlatoustovskii, S V

2004-01-01

A vast program of the experimental investigation of muon-catalyzed $dt$ fusion was performed at the JINR Phasotron. Parameters of the $dt$ cycle were obtained in a wide range of $D/T$ mixture conditions: temperatures of $20\\div 800$ K, densities of $0.2\\div1.2$ LHD and tritium concentrations of $15\\div 86\\%$. The results obtained are summarized.

Experimental loop for fast neutron fuels under normal, abnormal, transient and emergency conditions

International Nuclear Information System (INIS)

Bauge, M.; Colomez, G.; Marfaing, R.J.; Mourain, M.

1976-01-01

Within the scope of safety experiments on power reactor fuels, an experimental loop is described which can, by reduction of the flow, flush the sodium joint of vented mixed carbide fuel elements and allow the study of the resulting phenomena. With the help of the annex laboratories at OSIRIS, the control test can be analyzed and followed, with special attention to the study of the migration of fission products inside and outside the fuel. This apparatus can, of course, also be used for testing the fuels under normal and abnormal working conditions [fr

Processes influencing migration of bioavailable organic compounds from polymers - investigated during biotic and abiotic testing under static and non-static conditions with varying S/V-ratios

DEFF Research Database (Denmark)

Corfitzen, Charlotte B.; Arvin, Erik; Albrechtsen, Hans-Jørgen

. The bioavailable migration from the polymer surface was influence by diffusion over the solid-liquid boundary layer under sterile conditions, which resulted in an inversely proportionally relationship between bioavailable migration expressed per unit surface area of material and the surface to volume ratio (S/V-ratio...... the effect of the boundary layer, since bioavailable migration was continuously consumed by the bacteria. Thus the driving force for the diffusion process was maintained at a maximum, thereby enhancing the bioavailable migration from the material surfaces. Thus neither non-static conditions nor varying S/V-ratios...

Experimental study of centrifugal pump performance under steam-water two-phase flow conditions at elevated pressures

International Nuclear Information System (INIS)

Chan, A.M.C.; Barreca, S.L.; Hartlen, R.T.

1991-01-01

The performance of a centrifugal pump under two-phase flow conditions was studied in a closed loop. System voids of increasing magnitude were attained by draining water from the loop in steps. The operating temperature/pressure were varied from 110 degrees C/0.15 MPa to 260 degrees C/4.7 MPa. Only tests in the first quadrant were conducted. In this paper the head-flow characteristics and pump head degradation data are presented and discussed

SPINE: SParse eIgengene NEtwork linking gene expression clusters in Dehalococcoides mccartyi to perturbations in experimental conditions.

Directory of Open Access Journals (Sweden)

Cresten B Mansfeldt

Full Text Available We present a statistical model designed to identify the effect of experimental perturbations on the aggregate behavior of the transcriptome expressed by the bacterium Dehalococcoides mccartyi strain 195. Strains of Dehalococcoides are used in sub-surface bioremediation applications because they organohalorespire tetrachloroethene and trichloroethene (common chlorinated solvents that contaminate the environment to non-toxic ethene. However, the biochemical mechanism of this process remains incompletely described. Additionally, the response of Dehalococcoides to stress-inducing conditions that may be encountered at field-sites is not well understood. The constructed statistical model captured the aggregate behavior of gene expression phenotypes by modeling the distinct eigengenes of 100 transcript clusters, determining stable relationships among these clusters of gene transcripts with a sparse network-inference algorithm, and directly modeling the effect of changes in experimental conditions by constructing networks conditioned on the experimental state. Based on the model predictions, we discovered new response mechanisms for DMC, notably when the bacterium is exposed to solvent toxicity. The network identified a cluster containing thirteen gene transcripts directly connected to the solvent toxicity condition. Transcripts in this cluster include an iron-dependent regulator (DET0096-97 and a methylglyoxal synthase (DET0137. To validate these predictions, additional experiments were performed. Continuously fed cultures were exposed to saturating levels of tetrachloethene, thereby causing solvent toxicity, and transcripts that were predicted to be linked to solvent toxicity were monitored by quantitative reverse-transcription polymerase chain reaction. Twelve hours after being shocked with saturating levels of tetrachloroethene, the control transcripts (encoding for a key hydrogenase and the 16S rRNA did not significantly change. By contrast

Experimental determination of the energy efficiency of an air-cooled chiller under part load conditions

International Nuclear Information System (INIS)

Yu, F.W.; Chan, K.T.

2005-01-01

In cities located in a subtropical climate, air-cooled chillers are commonly used to provide cooling to the indoor environment. This accounts for the increasing electricity demand of buildings over the decades. This paper investigates how the condensing temperature serves to accurately determine the energy efficiency, or coefficient of performance (COP), of air-cooled chillers under part load conditions. An experiment on an air-cooled reciprocating chiller showed that for any given operating condition, the COP of the chiller varies, depending on how the condensing temperature is controlled. A sensitivity analysis is implemented to investigate to what extent COP is responding to changes in operating variables and confirms that the condensing temperature is an adequate variable to gauge COP under various operating conditions. The specifications of the upper limit for the condensing temperature in order to improve the energy efficiency of air-cooled chillers are discussed. The results of this work will give designers and researchers a good idea about how to model chiller energy performance curves in the thermal and energy computation exercises

International experience in conditioning spent fuel elements

International Nuclear Information System (INIS)

Ashton, P.

1991-04-01

The purpose of this report is to compile and present in a clear form international experience (USA, Canada, Sweden, FRG, UK, Japan, Switzerland) gained to date in conditioning spent fuel elements. The term conditioning is here taken to mean the handling and packaging of spent fuel elements for short- or long-term storage or final disposal. Plants of a varying nature fall within this scope, both in terms of the type of fuel element treated and the plant purpose eg. experimental or production plant. Emphasis is given to plants which bear some similarity to the concept developed in Germany for direct disposal of spent fuel elements. Worldwide, however, relatively few conditioning plants are in existence or have been conceived. Hence additional plants have been included where aspects of the experience gained are also of relevance eg. plants developed for the consolidation of spent fuel elements. (orig./HP) [de

Bounds and asymptotics for orthogonal polynomials for varying weights

CERN Document Server

Levin, Eli

2018-01-01

This book establishes bounds and asymptotics under almost minimal conditions on the varying weights, and applies them to universality limits and entropy integrals.  Orthogonal polynomials associated with varying weights play a key role in analyzing random matrices and other topics.  This book will be of use to a wide community of mathematicians, physicists, and statisticians dealing with techniques of potential theory, orthogonal polynomials, approximation theory, as well as random matrices. .

Experimental verification of boundary conditions for numerical simulation of airflow in a benchmark ventilation channel

Directory of Open Access Journals (Sweden)

Lizal Frantisek

2016-01-01

Full Text Available Correct definition of boundary conditions is crucial for the appropriate simulation of a flow. It is a common practice that simulation of sufficiently long upstream entrance section is performed instead of experimental investigation of the actual conditions at the boundary of the examined area, in the case that the measurement is either impossible or extremely demanding. We focused on the case of a benchmark channel with ventilation outlet, which models a regular automotive ventilation system. At first, measurements of air velocity and turbulence intensity were performed at the boundary of the examined area, i.e. in the rectangular channel 272.5 mm upstream the ventilation outlet. Then, the experimentally acquired results were compared with results obtained by numerical simulation of further upstream entrance section defined according to generally approved theoretical suggestions. The comparison showed that despite the simple geometry and general agreement of average axial velocity, certain difference was found in the shape of the velocity profile. The difference was attributed to the simplifications of the numerical model and the isotropic turbulence assumption of the used turbulence model. The appropriate recommendations were stated for the future work.

Experimental Assessment of a Helical Coil Heat Exchanger Operating at Subcritical and Supercritical Conditions in a Small-Scale Solar Organic Rankine Cycle

Directory of Open Access Journals (Sweden)

Marija Lazova

2017-05-01

Full Text Available In this study, the performance of a helical coil heat exchanger operating at subcritical and supercritical conditions is analysed. The counter-current heat exchanger was specially designed to operate at a maximal pressure and temperature of 42 bar and 200 °C, respectively. The small-scale solar organic Rankine cycle (ORC installation has a net power output of 3 kWe. The first tests were done in a laboratory where an electrical heater was used instead of the concentrated photovoltaic/thermal (CPV/T collectors. The inlet heating fluid temperature of the water was 95 °C. The effects of different parameters on the heat transfer rate in the heat exchanger were investigated. Particularly, the performance analysis was elaborated considering the changes of the mass flow rate of the working fluid (R-404A in the range of 0.20–0.33 kg/s and the inlet pressure varying from 18 bar up to 41 bar. Hence, the variation of the heat flux was in the range of 5–9 kW/m2. The results show that the working fluid’s mass flow rate has significant influence on the heat transfer rate rather than the operational pressure. Furthermore, from the comparison between the experimental results with the heat transfer correlations from the literature, the experimental results fall within the uncertainty range for the supercritical analysis but there is a deviation of the investigated subcritical correlations.

Dual Extended Kalman Filter for the Identification of Time-Varying Human Manual Control Behavior

Science.gov (United States)

Popovici, Alexandru; Zaal, Peter M. T.; Pool, Daan M.

2017-01-01

A Dual Extended Kalman Filter was implemented for the identification of time-varying human manual control behavior. Two filters that run concurrently were used, a state filter that estimates the equalization dynamics, and a parameter filter that estimates the neuromuscular parameters and time delay. Time-varying parameters were modeled as a random walk. The filter successfully estimated time-varying human control behavior in both simulated and experimental data. Simple guidelines are proposed for the tuning of the process and measurement covariance matrices and the initial parameter estimates. The tuning was performed on simulation data, and when applied on experimental data, only an increase in measurement process noise power was required in order for the filter to converge and estimate all parameters. A sensitivity analysis to initial parameter estimates showed that the filter is more sensitive to poor initial choices of neuromuscular parameters than equalization parameters, and bad choices for initial parameters can result in divergence, slow convergence, or parameter estimates that do not have a real physical interpretation. The promising results when applied to experimental data, together with its simple tuning and low dimension of the state-space, make the use of the Dual Extended Kalman Filter a viable option for identifying time-varying human control parameters in manual tracking tasks, which could be used in real-time human state monitoring and adaptive human-vehicle haptic interfaces.

SOFC regulation at constant temperature: Experimental test and data regression study

International Nuclear Information System (INIS)

Barelli, L.; Bidini, G.; Cinti, G.; Ottaviano, A.

2016-01-01

Highlights: • SOFC operating temperature impacts strongly on its performance and lifetime. • Experimental tests were carried out varying electric load and feeding mixture gas. • Three different anodic inlet gases were tested maintaining constant temperature. • Cathodic air flow rate was used to maintain constant its operating temperature. • Regression law was defined from experimental data to regulate the air flow rate. - Abstract: The operating temperature of solid oxide fuel cell stack (SOFC) is an important parameter to be controlled, which impacts the SOFC performance and its lifetime. Rapid temperature change implies a significant temperature differences between the surface and the mean body leading to a state of thermal shock. Thermal shock and thermal cycling introduce stress in a material due to temperature differences between the surface and the interior, or between different regions of the cell. In this context, in order to determine a control law that permit to maintain constant the fuel cell temperature varying the electrical load and the infeed fuel mixture, an experimental activity were carried out on a planar SOFC short stack to analyse stack temperature. Specifically, three different anodic inlet gas compositions were tested: pure hydrogen, reformed natural gas with steam to carbon ratio equal to 2 and 2.5. By processing the obtained results, a regression law was defined to regulate the air flow rate to be provided to the fuel cell to maintain constant its operating temperature varying its operating conditions.

Children's Understanding of Experimental Contrast and Experimental Control: An Inventory for Primary School

Science.gov (United States)

Osterhaus, Christopher; Koerber, Susanne; Sodian, Beate

2015-01-01

Experimentation skills are a central component of scientific thinking, and many studies have investigated whether and when primary-school children develop adequate experimentation strategies. However, the answers to these questions vary substantially depending on the type of task that is used: while discovery tasks, which require children to…

A Comparative Experimental Study of Fixed Temperature and Fixed Heat Flux Boundary Conditions in Turbulent Thermal Convection

Science.gov (United States)

Huang, Shi-Di; Wang, Fei; Xi, Heng-Dong; Xia, Ke-Qing

2014-11-01

We report an experimental study of the influences of thermal boundary condition in turbulent thermal convection. Two configurations were examined: one was fixed heat flux at the bottom boundary and fixed temperature at the top (HC cells); the other was fixed temperature at both boundaries (CC cells). It is found that the flow strength in the CC cells is on average 9% larger than that in the HC ones, which could be understood as change in plume emission ability under different boundary conditions. It is further found, rather surprisingly, that flow reversals of the large-scale circulation occur more frequently in the CC cell, despite a stronger large-scale flow and more uniform temperature distribution over the boundaries. These findings provide new insights into turbulent thermal convection and should stimulate further studies, especially experimental ones. This work is supported by the Hong Kong Research Grants Council under Grant No. CUHK 403712.

A reciprocal Wald theorem for varying gravitational function

International Nuclear Information System (INIS)

Fay, Stephane

2004-01-01

We study when a cosmological constant is a natural issue if it is mimicked by the potential of a massive Hyperextended Scalar Tensor theory with a perfect fluid for Bianchi type I and V models. We then deduce a reciprocal Wald theorem giving the conditions such that the potential tends to a non vanishing constant when the gravitational function varies. We also get the conditions allowing the potential to vanish or diverge. (orig.)

Stability Control of Force-Reflected Nonlinear Multilateral Teleoperation System under Time-Varying Delays

Directory of Open Access Journals (Sweden)

Da Sun

2016-01-01

Full Text Available A novel control algorithm based on the modified wave-variable controllers is proposed to achieve accurate position synchronization and reasonable force tracking of the nonlinear single-master-multiple-slave teleoperation system and simultaneously guarantee overall system’s stability in the presence of large time-varying delays. The system stability in different scenarios of human and environment situations has been analyzed. The proposed method is validated through experimental work based on the 3-DOF trilateral teleoperation system consisting of three different manipulators. The experimental results clearly demonstrate the feasibility of the proposed algorithm to achieve high transparency and robust stability in nonlinear single-master-multiple-slave teleoperation system in the presence of time-varying delays.

Quantum Hall resistance standard in graphene devices under relaxed experimental conditions

Science.gov (United States)

Schopfer, F.; Ribeiro-Palau, R.; Lafont, F.; Brun-Picard, J.; Kazazis, D.; Michon, A.; Cheynis, F.; Couturaud, O.; Consejo, C.; Jouault, B.; Poirier, W.

Large-area and high-quality graphene devices synthesized by CVD on SiC are used to develop reliable electrical resistance standards, based on the quantum Hall effect (QHE), with state-of-the-art accuracy of 1x10-9 and under an extended range of experimental conditions of magnetic field (down to 3.5 T), temperature (up to 10 K) or current (up to 0.5 mA). These conditions are much relaxed as compared to what is required by GaAs/AlGaAs standards and will enable to broaden the use of the primary quantum electrical standards to the benefit of Science and Industry for electrical measurements. Furthermore, by comparison of these graphene devices with GaAs/AlGaAs standards, we demonstrate the universality of the QHE within an ultimate uncertainty of 8.2x10-11. This suggests the exact relation of the quantized Hall resistance with the Planck constant and the electron charge, which is crucial for the new SI to be based on fixing such fundamental constants. These results show that graphene realizes its promises and demonstrates its superiority over other materials for a demanding application. Nature Nanotech. 10, 965-971, 2015, Nature Commun. 6, 6806, 2015

Impact of Varying Wave Conditions on the Mobility of Arsenic in a Nearshore Aquifer on the Great Lakes

Science.gov (United States)

Rakhimbekova, S.; O'Carroll, D. M.; Robinson, C. E.

2017-12-01

Groundwater-coastal water interactions play an important role in controlling the behavior of inorganic chemicals in nearshore aquifers and the subsequent flux of these chemicals to receiving coastal waters. Previous studies have shown that dynamic groundwater flows and water exchange across the sediment-water interface can set up strong geochemical gradients and an important reaction zone in a nearshore aquifer that affect the fate of reactive chemicals. There is limited understanding of the impact of transient coastal forcing such as wave conditions on groundwater dynamics and geochemistry in a nearshore aquifer. The goal of this study was to assess the impact of intensified wave conditions on the behavior of arsenic in a nearshore aquifer and to determine the hydrological and geochemical factors controlling its fate and ultimate delivery to receiving coastal waters. Field investigations were conducted over the period of intensified wave conditions on a freshwater beach on Lake Erie, Canada. High spatial resolution aqueous and sediment sampling was conducted to characterize the subsurface distribution of inorganic species in the nearshore aquifer. Numerical groundwater flow and transport simulations were conducted to evaluate wave-induced perturbations in the flow dynamics including characterizing changes in the groundwater flow recirculations in the nearshore aquifer. The combination of field data and numerical simulations reveal that varying wave conditions alter groundwater flows and set up geochemical transition zones within the aquifer resulting in the release and sequestration of arsenic. Interactions between oxic surface water, mildly reducing shallow groundwater, and reducing sulfur- and iron-rich deep groundwater promote dynamic iron, sulfur and manganese cycling which control the mobility of arsenic in the aquifer. The findings of this study have potential implications for the fate and transport of other reactive chemicals (e.g. phosphorus, mercury) in

Characterization of the startup transient electrokinetic flow in rectangular channels of arbitrary dimensions, zeta potential distribution, and time-varying pressure gradient.

Science.gov (United States)

Miller, Andrew; Villegas, Arturo; Diez, F Javier

2015-03-01

The solution to the startup transient EOF in an arbitrary rectangular microchannel is derived analytically and validated experimentally. This full 2D transient solution describes the evolution of the flow through five distinct periods until reaching a final steady state. The derived analytical velocity solution is validated experimentally for different channel sizes and aspect ratios under time-varying pressure gradients. The experiments used a time resolved micro particle image velocimetry technique to calculate the startup transient velocity profiles. The measurements captured the effect of time-varying pressure gradient fields derived in the analytical solutions. This is tested by using small reservoirs at both ends of the channel which allowed a time-varying pressure gradient to develop with a time scale on the order of the transient EOF. Results showed that under these common conditions, the effect of the pressure build up in the reservoirs on the temporal development of the transient startup EOF in the channels cannot be neglected. The measurements also captured the analytical predictions for channel walls made of different materials (i.e., zeta potentials). This was tested in channels that had three PDMS and one quartz wall, resulting in a flow with an asymmetric velocity profile due to variations in the zeta potential between the walls. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Establishment and performance of an experimental green roof under extreme climatic conditions.

Science.gov (United States)

Klein, Petra M; Coffman, Reid

2015-04-15

Green roofs alter the surface energy balance and can help in mitigating urban heat islands. However, the cooling of green roofs due to evapotranspiration strongly depends on the climatic conditions, and vegetation type and density. In the Southern Central Plains of the United States, extreme weather events, such as high winds, heat waves and drought conditions pose challenges for successful implementation of green roofs, and likely alter their standard performance. The National Weather Center Experimental Green Roof, an interdisciplinary research site established in 2010 in Norman, OK, aimed to investigate the ecological performance and surface energy balance of green roof systems. Starting in May 2010, 26 months of vegetation studies were conducted and the radiation balance, air temperature, relative humidity, and buoyancy fluxes were monitored at two meteorological stations during April-October 2011. The establishment of a vegetative community trended towards prairie plant dominance. High mortality of succulents and low germination of grasses and herbaceous plants contributed to low vegetative coverage. In this condition succulent diversity declined. Bouteloua gracilis and Delosperma cooperi showed typological dominance in harsh climatic conditions, while Sedum species experienced high mortality. The plant community diversified through volunteers such as Euphorbia maculate and Portulaca maculate. Net radiation measured at a green-roof meteorological station was higher than at a control station over the original, light-colored roofing material. These findings indicate that the albedo of the green roof was lower than the albedo of the original roofing material. The low vegetative coverage during the heat and drought conditions in 2011, which resulted in the dark substrate used in the green roof containers being exposed, likely contributed to the low albedo values. Nevertheless, air temperatures and buoyancy fluxes were often lower over the green roof indicating

Experimental study on neptunium migration under in situ geochemical conditions

Science.gov (United States)

Kumata, M.; Vandergraaf, T. T.

1998-12-01

Results are reported for migration experiments performed with Np under in situ geochemical conditions over a range of groundwater flow rates in columns of crushed rock in a specially designed facility at the 240-level of the Underground Research Laboratory (URL) near Pinawa, Manitoba, Canada. This laboratory is situated in an intrusive granitic rock formation, the Lac du Bonnet batholith. Highly altered granitic rock and groundwater were obtained from a major subhorizontal fracture zone at a depth of 250 m in the URL. The granite was wet-crushed and wet-sieved with groundwater from this fracture zone. The 180-850-μm size fraction was selected and packed in 20-cm long, 2.54-cm in diameter Teflon™-lined stainless steel columns. Approximately 30-ml vols of groundwater containing 3HHO and 237Np were injected into the columns at flow rates of 0.3, 1, and 3 ml/h, followed by elution with groundwater, obtained from the subhorizontal fracture, at the same flow rates, for a period of 95 days. Elution profiles for 3HHO were obtained, but no 237Np was detected in the eluted groundwater. After terminating the migration experiments, the columns were frozen, the column material was removed and cut into twenty 1-cm thick sections and each section was analyzed by gamma spectrometry. Profiles of 237Np were obtained for the three columns. A one-dimensional transport model was fitted to the 3HHO breakthrough curves to obtain flow parameters for this experiment. These flow parameters were in turn applied to the 237Np concentration profiles in the columns to produce sorption and dispersion coefficients for Np. The results show a strong dependence of retardation factors ( Rf) on flow rate. The decrease in the retarded velocity of the neptunium ( Vn) varied over one order of magnitude under the geochemical conditions for these experiments.

Parental care mitigates carry-over effects of poor early conditions on offspring growth

Science.gov (United States)

Auer, Sonya K.; Martin, Thomas E.

2017-01-01

Poor developmental conditions can have long-lasting negative effects on offspring phenotypes, but impacts often differ among species. Contrasting responses may reflect disparities in experimental protocols among single-species studies or inherent differences among species in their sensitivity to early conditions and/or ability to mitigate negative impacts. We used a common experimental protocol to assess and compare the role of parental care in mitigating effects of poor early conditions on offspring among 4 sympatric bird species in the wild. We experimentally induced low incubation temperatures and examined effects on embryonic developmental rates, hatching success, nestling growth rates, and parental responses. We examined the generality of these effects across 4 species that differ in their phylogenetic history, breeding ecology, and life histories. We found that cooling led to delayed hatching in all species, but carry-over effects on offspring differed among species. Parents of some but not all species increased their offspring provisioning rates in response to experimental cooling with critical benefits for offspring growth rates. Our study shows for the first time that species exhibit clear differences in the degree to which they are affected by poor early conditions. Observed differences among species demonstrate that parental care is a critical mechanism for mitigating potential negative effects on offspring and suggest that parental responses may be constrained to varying degrees by ecology and life histories.

Organic matter cycling in a neotropical reservoir: effects of temperature and experimental conditions

Directory of Open Access Journals (Sweden)

Flávia Bottino

2013-06-01

Full Text Available AIM:This study reports a comparison between decomposition kinetics of detritus derived from two macrophyte species (Polygonum lapathifolium L.: Polygonaceae; Eichhornia azurea (Sw. Kunth.: Pontederiaceae growing in a neotropical reservoir (Brazil, under laboratory and field conditions, in order to assess hypotheses on the main differences in factors affecting organic matter cycling, including the effect of temperature. METHODS: Plant and water samples were collected from the reservoir in August 2009. In field incubation mass loss was assessed using a litter bag technique and in the laboratory the decay was followed using a decomposition chamber maintained under controlled conditions (i.e. in the dark, at 15 ºC and 25 ºC. A kinetic model was adopted to explain and compare the organic matter decay, ANOVA (Repeated Measures testing was used to describe the differences between the treatments and a linear correlation was used to compare in situ and in vitro experiments. RESULTS: The mass decay was faster in natural conditions with rapid release of the labile-soluble portion. The simulated values of mineralization rates of dissolved organic matter and refractory organic matter were rapid in high temperatures (25 ºC. The high Q10 results (mainly for E. azurea, and experimental conditions, and outcomes of ANOVA testing indicate the temperature variation (10 ºC influence the rates of mass decay. CONCLUSIONS: The results suggested rapid organic matter cycling in warm months (from October to December supporting the microbial loop. Although the particulate organic matter losses are high in field conditions the results are of the same magnitude in both conditions suggesting an equivalence of the mass decay kinetic.

On the formation of sulphuric acid – amine clusters in varying atmospheric conditions and its influence on atmospheric new particle formation

Directory of Open Access Journals (Sweden)

I. K. Ortega

2012-10-01

Full Text Available Sulphuric acid is a key component in atmospheric new particle formation. However, sulphuric acid alone does not form stable enough clusters to initiate particle formation in atmospheric conditions. Strong bases, such as amines, have been suggested to stabilize sulphuric acid clusters and thus participate in particle formation. We modelled the formation rate of clusters with two sulphuric acid and two amine molecules (JA2B2 at varying atmospherically relevant conditions with respect to concentrations of sulphuric acid ([H2SO4], dimethylamine ([DMA] and trimethylamine ([TMA], temperature and relative humidity (RH. We also tested how the model results change if we assume that the clusters with two sulphuric acid and two amine molecules would act as seeds for heterogeneous nucleation of organic vapours (other than amines with higher atmospheric concentrations than sulphuric acid. The modelled formation rates JA2B2 were functions of sulphuric acid concentration with close to quadratic dependence, which is in good agreement with atmospheric observations of the connection between the particle formation rate and sulphuric acid concentration. The coefficients KA2B2 connecting the cluster formation rate and sulphuric acid concentrations as JA2B2=KA2B2[H2SO4]2 turned out to depend also on amine concentrations, temperature and relative humidity. We compared the modelled coefficients KA2B2 with the corresponding coefficients calculated from the atmospheric observations (Kobs from environments with varying temperatures and levels of anthropogenic influence. By taking into account the modelled behaviour of JA2B2 as a function of [H2SO4], temperature and RH, the atmospheric particle formation rate was reproduced more closely than with the traditional semi-empirical formulae based on sulphuric acid concentration only. The formation rates of clusters with two sulphuric acid and two amine molecules with different amine compositions (DMA or TMA or one of both had

Volatility spillover and time-varying conditional correlation between DDGS, corn, and soybean meal markets

NARCIS (Netherlands)

Etienne, Xiaoli L.; Trujillo-Barrera, Andrés; Hoffman, Linwood A.

2017-01-01

We find distiller's dried grains with solubles (DDGS) prices to be positively correlated with both corn and soybean meal prices in the long run. However, neither corn nor soybean meal prices respond to deviations from this long-run relationship. We also identify strong time-varying dynamic

Experimental analysis of a direct expansion solar assisted heat pump with integral storage tank for domestic water heating under zero solar radiation conditions

International Nuclear Information System (INIS)

Fernández-Seara, José; Piñeiro, Carolina; Alberto Dopazo, J.; Fernandes, F.; Sousa, Paulo X.B.

2012-01-01

Highlights: ► We analyze a direct expansion solar assisted heat pump under zero solar radiation. ► We determine the COP and equivalent seasonal performance factors (SPFe). ► We determine the main components’ performance under transient operating conditions. ► The Huang and Lee performance evaluation method provides a characteristic COP of 3.23. - Abstract: This paper deals with the experimental evaluation of the performance of a direct expansion solar assisted heat pump water heating (DX-SAHPWH) system working under zero solar radiation conditions at static heating operation mode of the storage tank. The DX-SAHPWH system includes two bare solar collectors as evaporator, a R134a rotary-type hermetic compressor, a thermostatic expansion valve and a helical coil condenser immersed in a 300 L water storage tank. The zero solar radiation and stable ambient air temperature working conditions were established by placing the solar collectors into a climate chamber. The analysis is based on experimental data taken from the DX-SAHPWH provided by the manufacturer and equipped with an appropriate data acquisition system. In the paper, the experimental facility, the data acquisition system and the experimental methodology are described. Performance parameters to evaluate the energy efficiency, such as COP and equivalent seasonal performance factors (SPFe) for the heating period, and the water thermal stratification in the storage tank are defined and obtained from the experimental data. Results from the experimental analysis under transient operating working conditions of the DX-SAHPWH system and its main components are shown and discussed. Lastly, the Huang and Lee DX-SAHPWH performance evaluation method was applied resulting in a characteristic COP of 3.23 for the DX-SAHPWH system evaluated under zero solar radiation condition.

Design of Robust AMB Controllers for Rotors Subjected to Varying and Uncertain Seal Forces

DEFF Research Database (Denmark)

Lauridsen, Jonas Skjødt; Santos, Ilmar

2017-01-01

This paper demonstrates the design and simulation results of model based controllers for AMB systems, subjectedto uncertain and changing dynamic seal forces. Specifically, a turbocharger with a hole-pattern seal mounted acrossthe balance piston is considered. The dynamic forces of the seal, which...... are dependent on the operational conditions,have a significant effect on the overall system dynamics. Furthermore, these forces are considered uncertain.The nominal and the uncertainty representation of the seal model are established using results from conventionalmodelling approaches, i.e. CFD and Bulkflow......, and experimental results. Three controllers are synthesized: I) AnH∞ controller based on nominal plant representation, II) A µ controller, designed to be robust against uncertaintiesin the dynamic seal model and III) a Linear Parameter Varying (LPV) controller, designed to provide a unifiedperformance over a large...

Experimental investigations on steel-concrete composite columns for varying parameters

Science.gov (United States)

Aparna, V.; Vivek, D.; Neelima, Kancharla; Karthikeyan, B.

2017-07-01

In this study, the experimental investigations on steel tubes filled with different types of concrete are presented. Steel tubes filled with fibre reinforced concrete using lathe waste and steel tube with concerned confined with steel mesh were investigated. The combinations were compared with steel tubes with conventional concrete. A total of 4 concrete filled steel tube (CFST) combinations were made with tubes of diameter 100 mm with wall thickness 1.6 mm and a height of 300 mm. Axial compression test to examine the resisting capacity of the columns and push-out test for noting the bond strength were performed. Coupon tests were also conducted to determine the mechanical properties of steel. The structural behaviour of the composite columns was evaluated from on the test results. It was observed that steel tube filled fibre reinforced possessed better bond strength and resistance to axial load.

Experimental study on frosting control of mobile air conditioning system with microchannel evaporator

International Nuclear Information System (INIS)

Qu Xiaohua; Shi Junye; Qi Zhaogang; Chen Jiangping

2011-01-01

In this paper, a newly developed frost control system is proposed. System bench tests and vehicle test in wind tunnel have been carried out to explore the anti-frosting performance of automotive air conditioning system with microchannel evaporator. The experimental results are compared with the baseline conventional laminated evaporator system. The test results show that the installation position of temperature sensor can dramatically affect the anti-frosting performance. The clutch switching on/off temperature range of the microchannel evaporator is also experimentally studied. The test results show that, with a proper installation position and on/off temperature range, the system COP can be improved, and meanwhile the panel vents' air off temperature can be reduced, and temperature swing can be reduced. - Highlights: → The frost control systems were tested with microchannel and laminated evaporators separately. → The installation position of temperature sensor affects the anti-frosting performance. → Temperature control range affects the anti-frosting performance. → The panel vents' air off temperature and swing can be reduced by proper control parameters. → The system COP can be improved by proper control parameters.

Asymmetric Vibration of Polar Orthotropic Annular Circular Plates of Quadratically Varying Thickness with Same Boundary Conditions

Directory of Open Access Journals (Sweden)

N. Bhardwaj

2008-01-01

Full Text Available In the present paper, asymmetric vibration of polar orthotropic annular circular plates of quadratically varying thickness resting on Winkler elastic foundation is studied by using boundary characteristic orthonormal polynomials in Rayleigh-Ritz method. Convergence of the results is tested and comparison is made with results already available in the existing literature. Numerical results for the first ten frequencies for various values of parameters describing width of annular plate, thickness profile, material orthotropy and foundation constant for all three possible combinations of clamped, simply supported and free edge conditions are shown and discussed. It is found that (a higher elastic property in circumferential direction leads to higher stiffness against lateral vibration; (b Lateral vibration characteristics of F-Fplates is more sensitive towards parametric changes in material orthotropy and foundation stiffness than C-C and S-Splates; (c Effect of quadratical thickness variation on fundamental frequency is more significant in cases of C-C and S-S plates than that of F-Fplates. Thickness profile which is convex relative to plate center-line tends to result in higher stiffness of annular plates against lateral vibration than the one which is concave and (d Fundamental mode of vibration of C-C and S-Splates is axisymmetrical while that of F-Fplates is asymmetrical.

Modelling Time-Varying Volatility in Financial Returns

DEFF Research Database (Denmark)

Amado, Cristina; Laakkonen, Helinä

2014-01-01

The “unusually uncertain” phase in the global financial markets has inspired many researchers to study the effects of ambiguity (or “Knightian uncertainty”) on the decisions made by investors and their implications for the capital markets. We contribute to this literature by using a modified...... version of the time-varying GARCH model of Amado and Teräsvirta (2013) to analyze whether the increasing uncertainty has caused excess volatility in the US and European government bond markets. In our model, volatility is multiplicatively decomposed into two time-varying conditional components: the first...... being captured by a stable GARCH(1,1) process and the second driven by the level of uncertainty in the financial market....

A method comparison of total and HMW adiponectin: HMW/total adiponectin ratio varies versus total adiponectin, independent of clinical condition.

Science.gov (United States)

van Andel, Merel; Drent, Madeleine L; van Herwaarden, Antonius E; Ackermans, Mariëtte T; Heijboer, Annemieke C

2017-02-01

Total and high-molecular-weight (HMW) adiponectin have been associated with endocrine and cardiovascular pathology. As no gold standard is available, the discussion about biological relevance of isoforms is complicated. In our study we perform a method comparison between two commercially available assays measuring HMW and total adiponectin, in various patient groups, thus contributing further to this discussion. We determined levels of HMW and total adiponectin using assays by Lumipulse® and Millipore® respectively, in 126 patients with different clinical characteristics (n=29 healthy volunteers, n=22 dialysis patients, n=25 elderly with body mass index (BMI) LUMIPULSE ∗0.5-0.9=total adiponectin MILLIPORE , albeit with significant deviation from linearity (p<0.001). Pearson's correlation was R=0.987 (p=0.000). No significant differences between patient groups were observed (p=0.190). The HMW/total adiponectin ratio varies with total adiponectin concentration independent of clinical conditions studied. Our results imply that total and HMW adiponectin have similar utility when assessing adiponectin levels in blood, as the ratio is independent of clinical condition. Copyright © 2016 Elsevier B.V. All rights reserved.

Spontaneous burp phenomenon: analysis of experimental data and approach to theoretical interpretation

International Nuclear Information System (INIS)

Shabalin, E.

2004-01-01

Cases of spontaneous release of energy (''burp'') were observed numerously in solid methane, water ice and other hydrogeneous compounds irradiated in fast neutron fields with absorbed dose 2-10 MGy. Nature of this phenomenon is that accumulation of radicals and thermal instability of a sample under due concentration of radicals culminate to autocatalytic reaction of their recombination. The most odious feature of this phenomenon is that irradiation time, before a burp occurs, varies significantly even in identical irradiation condition. Respectively, amount of released energy varies as well. For example, in URAM-2 experiments with water ice, irradiation time before appearance of spontaneous burp varied from 5 hours to 11 hours for equal samples and up to 20 hours for the smallest sample. Another feature of the phenomenon is that regularities for occurrence of spontaneous release of energy (that is, dependence on temperature, size of sample, absorbed dose) can't be extracted explicitly from experimental data, if applying known relations for critical concentration of radicals, namely: Semenov's and Frank-Kamenetski's conditions of thermal instability of a sample, Jackson's relation for chain process of recombination of uniformly distributed radicals, critical condition based on accounting for acceleration of a process of recombination in the regions of micro-cracks, and, finally, critical condition for irregular distribution of radicals proposed by the author of this article. Not one of these theories predicts casual character of a burp on macro-scale basis. So that, notwithstanding fair amount of experimental data on spontaneous burps, it is still impossible to derive well-balanced theory of this phenomenon. One attempt to understand a reason for the strange behavior of spontaneous burping is a probabilistic, cluster model of spontaneous release of energy, developed in the chapter 4 of this paper. Spontaneous burps observed during URAM-2 project and in solid methane

A Novel Time-Varying Friction Compensation Method for Servomechanism

Directory of Open Access Journals (Sweden)

Bin Feng

2015-01-01

Full Text Available Friction is an inevitable nonlinear phenomenon existing in servomechanisms. Friction errors often affect their motion and contour accuracies during the reverse motion. To reduce friction errors, a novel time-varying friction compensation method is proposed to solve the problem that the traditional friction compensation methods hardly deal with. This problem leads to an unsatisfactory friction compensation performance and the motion and contour accuracies cannot be maintained effectively. In this method, a trapezoidal compensation pulse is adopted to compensate for the friction errors. A generalized regression neural network algorithm is used to generate the optimal pulse amplitude function. The optimal pulse duration function and the pulse amplitude function can be established by the pulse characteristic parameter learning and then the optimal friction compensation pulse can be generated. The feasibility of friction compensation method was verified on a high-precision X-Y worktable. The experimental results indicated that the motion and contour accuracies were improved greatly with reduction of the friction errors, in different working conditions. Moreover, the overall friction compensation performance indicators were decreased by more than 54% and this friction compensation method can be implemented easily on most of servomechanisms in industry.

Varying Constants, Gravitation and Cosmology

Directory of Open Access Journals (Sweden)

Jean-Philippe Uzan

2011-03-01

Full Text Available Fundamental constants are a cornerstone of our physical laws. Any constant varying in space and/or time would reflect the existence of an almost massless field that couples to matter. This will induce a violation of the universality of free fall. Thus, it is of utmost importance for our understanding of gravity and of the domain of validity of general relativity to test for their constancy. We detail the relations between the constants, the tests of the local position invariance and of the universality of free fall. We then review the main experimental and observational constraints that have been obtained from atomic clocks, the Oklo phenomenon, solar system observations, meteorite dating, quasar absorption spectra, stellar physics, pulsar timing, the cosmic microwave background and big bang nucleosynthesis. At each step we describe the basics of each system, its dependence with respect to the constants, the known systematic effects and the most recent constraints that have been obtained. We then describe the main theoretical frameworks in which the low-energy constants may actually be varying and we focus on the unification mechanisms and the relations between the variation of different constants. To finish, we discuss the more speculative possibility of understanding their numerical values and the apparent fine-tuning that they confront us with.

Experimental Study of Impregnation Birch and Aspen Samples

Directory of Open Access Journals (Sweden)

Igor Vladislavovich Grigorev

2014-10-01

Full Text Available An experimental study of wood impregnation was implemented by applying centrifugal methods. The impregnants were a 10% aqueous solution of potassium chloride and a 2% aqueous solution of borax. Birch (Betula pendula and aspen (Populus tremula wood samples in different moisture content were tested. The impregnation time in the centrifugal device were 30 seconds repeated 21 times, and the samples were measured after every 30 seconds. The experimental results were fitted to a nonlinear filtration law, which indicated that the centrifugal wood impregnation was dependent on wood species, wood moisture, rotational speed, and radius. Determination of rotational speed and centrifuge radius for impregnating aspen and birch at varying lengths and humidity under conditions of the nonlinear impregnant filtration law can be done using the example charts that were developed and presented in this study.

Conservadorismo condicional: estudo a partir de variáveis econômicas Conditional conservatism: a study based on economic variables

Directory of Open Access Journals (Sweden)

Rafael de Lacerda Moreira

2010-12-01

Full Text Available A Contabilidade, na perspectiva da abordagem da informação, volta-se à utilidade da informação. O Conservadorismo Condicional está ligado à tendência de a Contabilidade exigir um maior grau de verificação das boas notícias para reconhecê-las no resultado em relação ao grau de verificação das más notícias. Em face das preocupações referentes à qualidade da informação contábil, o objetivo deste artigo consiste em analisar o reflexo do Conservadorismo Condicional no resultado contábil a partir de variáveis econômicas. O estudo utiliza o Modelo Reverso de Lucros Associados a Retornos (BASU, 1997 e o modelo proposto por Kahn e Watts (2009, que analisam a relação entre as variáveis lucro contábil e retorno econômico, utilizando os valores dos retornos positivos e negativos como proxy de boas e más notícias, e outras variáveis largamente aceitas na avaliação do conservadorismo. Para tanto, foram estimados os modelos estatísticos para uma amostra de 96 empresas para o período de 2005 a 2007 partindo de informações anuais disponíveis no Economática® e dados reportados em notas explicativas. Com o objetivo de selecionar um evento econômico que pode impactar no reconhecimento assimétrico do resultado econômico, decidiu-se comparar os resultados entre empresas listadas nos níveis de governança da Bovespa com as demais empresas. Os resultados obtidos confirmam a hipótese de utilização de conservadorismo condicional na mensuração do resultado das companhias da amostra. A diferenciação positiva quanto ao grau de conservadorismo para as empresas que aderiram aos níveis de governança não são conclusivas, visto que os modelos apresentaram resultados dispersos. As variáveis econômicas criam vantagens quando as más notícias não podem ser tão claramente visíveis nas Demonstrações Contábeis, podendo diminuir os resultados futuros esperados.Accounting from an information perspective looks at the

Experimental study on void fraction of two-phase flow inside a micro-fin tube

OpenAIRE

Koyama, Shigeru; Chen, Yongchang; Kitano, Ryuji; Kuwahara, Ken

2001-01-01

In this paper the void fraction and flow pattern of the two-phase flow in a micro-fin tube were investigated experimentally for a pure refrigerant HFC134a. The experiment was carried out at a pressure range of 0.6 and 1.2MPa with mass velocities of 90 and 180kg/m^2 s, in which the vapor quality varied from 0 to 1. The void fraction was measured by means of simultaneously closing valves of both sides of the test tube at adiabatic condition. Experimental results for the micro-fin tube were comp...

Experimental study of performance of a dry cooling and dedicated ventilation (DCDV) system under different space cooling load conditions

International Nuclear Information System (INIS)

Jia, Jie; Lee, W.L.; Chen, Hua

2013-01-01

Highlights: • This is an experimental study of the use of DCDV system for achieving the decoupling and energy saving objectives. • The study focuses on side-by-side comparison of the DCDV and conventional systems. • DCDV system can better achieve the desired space air conditions and is more energy efficient. • A prediction model has been developed to relate the possible condensation period with different operating parameters. • The results are useful for wider application of DCDV system. - Abstract: The use of DCDV system for decoupling dehumidification from cooling to achieve energy saving objective for air-conditioning of office environments in Hong Kong was confirmed effective based on simulation studies by the authors. However, given that simulation typically assumes a perfect control and feedback system, whether or not the benefits of DCDV system can be realized in practice, in particular under various space part load ratio (PLR) and sensible heat ratio (SHR) conditions, is subject to experimental verifications. In this study, a prototype which could be switched between the proposed DCDV system mode and the conventional system mode was constructed in a test facility for laboratory experiments. Through two sets of identical experiments under various space cooling load conditions, it was found that if compared to the conventional system, DCDV system could perform slightly better in achieving the desired indoor condition and in reducing the moisture-related air quality problems, but would result in 1–3% higher in cooling output. As for the overall coefficient of performance (COP o ), the DCDV system was found performed better by 5.6–7.2%. Additional experimental analysis was conducted for the development of a prediction model to relate the possible condensation period (ψ) on the DC coil with different operating parameters

Constitutive Equation with Varying Parameters for Superplastic Flow Behavior

Science.gov (United States)

Guan, Zhiping; Ren, Mingwen; Jia, Hongjie; Zhao, Po; Ma, Pinkui

2014-03-01

In this study, constitutive equations for superplastic materials with an extra large elongation were investigated through mechanical analysis. From the view of phenomenology, firstly, some traditional empirical constitutive relations were standardized by restricting some strain paths and parameter conditions, and the coefficients in these relations were strictly given new mechanical definitions. Subsequently, a new, general constitutive equation with varying parameters was theoretically deduced based on the general mechanical equation of state. The superplastic tension test data of Zn-5%Al alloy at 340 °C under strain rates, velocities, and loads were employed for building a new constitutive equation and examining its validity. Analysis results indicated that the constitutive equation with varying parameters could characterize superplastic flow behavior in practical superplastic forming with high prediction accuracy and without any restriction of strain path or deformation condition, showing good industrial or scientific interest. On the contrary, those empirical equations have low prediction capabilities due to constant parameters and poor applicability because of the limit of special strain path or parameter conditions based on strict phenomenology.

Experimental assessment for instantaneous temperature and heat flux measurements under Diesel motored engine conditions

International Nuclear Information System (INIS)

Torregrosa, A.J.; Bermúdez, V.; Olmeda, P.; Fygueroa, O.

2012-01-01

Higlights: ► We measured in-cylinder wall heat fluxes. ► We examine the effects of different engine parameters. ► Increasing air mass flow increase heat fluxes. ► The effect of engine speed can be masked by the effect of volumetric efficiency. ► Differences among the different walls have been found. - Abstract: The main goal of this work is to validate an innovative experimental facility and to establish a methodology to evaluate the influence of some of the engine parameters on local engine heat transfer behaviour under motored steady-state conditions. Instantaneous temperature measurements have been performed in order to estimate heat fluxes on a modified Diesel single cylinder combustion chamber. This study was divided into two main parts. The first one was the design and setting on of an experimental bench to reproduce Diesel conditions and perform local-instantaneous temperature measurements along the walls of the combustion chamber by means of fast response thermocouples. The second one was the development of a procedure for temperature signal treatment and local heat flux calculation based on one-dimensional Fourier analysis. A thermodynamic diagnosis model has been employed to characterise the modified engine with the new designed chamber. As a result of the measured data coherent findings have been obtained in order to understand local behaviour of heat transfer in an internal combustion engine, and the influence of engine parameters on local instantaneous temperature and heat flux, have been analysed.

Carbon allocation to major metabolites in illuminated leaves is not just proportional to photosynthesis when gaseous conditions (CO2 and O2 ) vary.

Science.gov (United States)

Abadie, Cyril; Bathellier, Camille; Tcherkez, Guillaume

2018-04-01

In gas-exchange experiments, manipulating CO 2 and O 2 is commonly used to change the balance between carboxylation and oxygenation. Downstream metabolism (utilization of photosynthetic and photorespiratory products) may also be affected by gaseous conditions but this is not well documented. Here, we took advantage of sunflower as a model species, which accumulates chlorogenate in addition to sugars and amino acids (glutamate, alanine, glycine and serine). We performed isotopic labelling with 13 CO 2 under different CO 2 /O 2 conditions, and determined 13 C contents to compute 13 C-allocation patterns and build-up rates. The 13 C content in major metabolites was not found to be a constant proportion of net fixed carbon but, rather, changed dramatically with CO 2 and O 2 . Alanine typically accumulated at low O 2 (hypoxic response) while photorespiratory intermediates accumulated under ambient conditions and at high photorespiration, glycerate accumulation exceeding serine and glycine build-up. Chlorogenate synthesis was relatively more important under normal conditions and at high CO 2 and its synthesis was driven by phosphoenolpyruvate de novo synthesis. These findings demonstrate that carbon allocation to metabolites other than photosynthetic end products is affected by gaseous conditions and therefore the photosynthetic yield of net nitrogen assimilation varies, being minimal at high CO 2 and maximal at high O 2 . © 2018 The Authors. New Phytologist © 2018 New Phytologist Trust.

Comparison of the kinetics of different Markov models for ligand binding under varying conditions

International Nuclear Information System (INIS)

Martini, Johannes W. R.; Habeck, Michael

2015-01-01

We recently derived a Markov model for macromolecular ligand binding dynamics from few physical assumptions and showed that its stationary distribution is the grand canonical ensemble [J. W. R. Martini, M. Habeck, and M. Schlather, J. Math. Chem. 52, 665 (2014)]. The transition probabilities of the proposed Markov process define a particular Glauber dynamics and have some similarity to the Metropolis-Hastings algorithm. Here, we illustrate that this model is the stochastic analog of (pseudo) rate equations and the corresponding system of differential equations. Moreover, it can be viewed as a limiting case of general stochastic simulations of chemical kinetics. Thus, the model links stochastic and deterministic approaches as well as kinetics and equilibrium described by the grand canonical ensemble. We demonstrate that the family of transition matrices of our model, parameterized by temperature and ligand activity, generates ligand binding kinetics that respond to changes in these parameters in a qualitatively similar way as experimentally observed kinetics. In contrast, neither the Metropolis-Hastings algorithm nor the Glauber heat bath reflects changes in the external conditions correctly. Both converge rapidly to the stationary distribution, which is advantageous when the major interest is in the equilibrium state, but fail to describe the kinetics of ligand binding realistically. To simulate cellular processes that involve the reversible stochastic binding of multiple factors, our pseudo rate equation model should therefore be preferred to the Metropolis-Hastings algorithm and the Glauber heat bath, if the stationary distribution is not of only interest

Comparison of the kinetics of different Markov models for ligand binding under varying conditions

Energy Technology Data Exchange (ETDEWEB)

Martini, Johannes W. R., E-mail: jmartin2@gwdg.de [Max Planck Institute for Developmental Biology, Tübingen (Germany); Felix Bernstein Institute for Mathematical Statistics in the Biosciences, University of Göttingen, Göttingen (Germany); Habeck, Michael, E-mail: mhabeck@gwdg.de [Felix Bernstein Institute for Mathematical Statistics in the Biosciences, University of Göttingen, Göttingen (Germany); Max Planck Institute for Biophysical Chemistry, Göttingen (Germany)

2015-03-07

We recently derived a Markov model for macromolecular ligand binding dynamics from few physical assumptions and showed that its stationary distribution is the grand canonical ensemble [J. W. R. Martini, M. Habeck, and M. Schlather, J. Math. Chem. 52, 665 (2014)]. The transition probabilities of the proposed Markov process define a particular Glauber dynamics and have some similarity to the Metropolis-Hastings algorithm. Here, we illustrate that this model is the stochastic analog of (pseudo) rate equations and the corresponding system of differential equations. Moreover, it can be viewed as a limiting case of general stochastic simulations of chemical kinetics. Thus, the model links stochastic and deterministic approaches as well as kinetics and equilibrium described by the grand canonical ensemble. We demonstrate that the family of transition matrices of our model, parameterized by temperature and ligand activity, generates ligand binding kinetics that respond to changes in these parameters in a qualitatively similar way as experimentally observed kinetics. In contrast, neither the Metropolis-Hastings algorithm nor the Glauber heat bath reflects changes in the external conditions correctly. Both converge rapidly to the stationary distribution, which is advantageous when the major interest is in the equilibrium state, but fail to describe the kinetics of ligand binding realistically. To simulate cellular processes that involve the reversible stochastic binding of multiple factors, our pseudo rate equation model should therefore be preferred to the Metropolis-Hastings algorithm and the Glauber heat bath, if the stationary distribution is not of only interest.

Protein folding: Defining a standard set of experimental conditions and a preliminary kinetic data set of two-state proteins

DEFF Research Database (Denmark)

Maxwell, Karen L.; Wildes, D.; Zarrine-Afsar, A.

2005-01-01

Recent years have seen the publication of both empirical and theoretical relationships predicting the rates with which proteins fold. Our ability to test and refine these relationships has been limited, however, by a variety of difficulties associated with the comparison of folding and unfolding ...... efforts is to set uniform standards for the experimental community and to initiate an accumulating, self-consistent data set that will aid ongoing efforts to understand the folding process....... constructs. The lack of a single approach to data analysis and error estimation, or even of a common set of units and reporting standards, further hinders comparative studies of folding. In an effort to overcome these problems, we define here a consensus set of experimental conditions (25°C at pH 7.0, 50 m...... rates, thermodynamics, and structure across diverse sets of proteins. These difficulties include the wide, potentially confounding range of experimental conditions and methods employed to date and the difficulty of obtaining correct and complete sequence and structural details for the characterized...

Uncertainty Quantification in Experimental Structural Dynamics Identification of Composite Material Structures

DEFF Research Database (Denmark)

Luczak, Marcin; Peeters, Bart; Kahsin, Maciej

2014-01-01

for uncertainty evaluation in experimentally estimated models. Investigated structures are plates, fuselage panels and helicopter main rotor blades as they represent different complexity levels ranging from coupon, through sub-component up to fully assembled structures made of composite materials. To evaluate......Aerospace and wind energy structures are extensively using components made of composite materials. Since these structures are subjected to dynamic environments with time-varying loading conditions, it is important to model their dynamic behavior and validate these models by means of vibration...

Multi-Fibre Optode Microsensors: affordable designs for monitoring oxygen in soils under varying environmental conditions

Science.gov (United States)

Rezanezhad, F.; Milojevic, T.; Parsons, C. T.; Smeaton, C. M.; Van Cappellen, P.

2017-12-01

, where the imaged data is transmitted remotely using a photo-logging system. The MuFO sensor is currently being tested at a Southern Ontario field site in a year-long experiment. Here we present the field and laboratory results of soil O2 monitoring by this newly developed MuFO microsensor system under varying environmental conditions.

Experimental investigation of the effects of blowing conditions and Mach number on the unsteady behavior of coolant ejection through a trailing edge cutback

International Nuclear Information System (INIS)

Barigozzi, Giovanna; Armellini, Alessandro; Mucignat, Claudio; Casarsa, Luca

2012-01-01

Highlights: ► Flow visualization and PIV documented the presence of large coherent structures. ► The presence of coherent structures is documented up to the vane trailing edge. ► Shape and direction of rotation of vortices change with injection conditions. ► Vortices morphology influences the film cooling effectiveness distributions. ► A Mach number increase moves vortices closer to the wall. - Abstract: The present paper shows the results of an experimental investigation into the unsteadiness of coolant ejection at the trailing edge of a highly loaded nozzle vane cascade. The trailing edge cooling scheme features a pressure side cutback with film cooling slots, stiffened by evenly spaced ribs in an inline configuration. Cooling air is also ejected through two rows of cylindrical holes placed upstream of the cutback. Tests were performed with a low inlet turbulence intensity level (Tu 1 = 1.6%), changing the cascade operating conditions from low speed (M 2is = 0.2) up to high subsonic regime (M 2is = 0.6), and with coolant to main stream mass flow ratio varied within the 0.5–2.0% range. Particle Image Velocimetry (PIV) and flow visualizations were used to investigate the unsteady mixing process taking place between coolant and main flow downstream of the cutback, up to the trailing edge. For all the tested conditions, the results show the presence of large coherent structures, which presence is still evident up to the trailing edge. Their shape and direction of rotation change with injection conditions, as a function of coolant to mainstream velocity ratio, strongly influencing the thermal protection capability of the injected coolant flow. The Mach number increase is only responsible for a positioning of such vortical structures closer to the wall, while the Strouhal number almost remains unchanged.

Modeling conditional correlations of asset returns

DEFF Research Database (Denmark)

Silvennoinen, Annastiina; Teräsvirta, Timo

2015-01-01

In this paper we propose a new multivariate GARCH model with time-varying conditional correlation structure. The time-varying conditional correlations change smoothly between two extreme states of constant correlations according to a predetermined or exogenous transition variable. An LM-test is d......In this paper we propose a new multivariate GARCH model with time-varying conditional correlation structure. The time-varying conditional correlations change smoothly between two extreme states of constant correlations according to a predetermined or exogenous transition variable. An LM......-test is derived to test the constancy of correlations and LM- and Wald tests to test the hypothesis of partially constant correlations. Analytical expressions for the test statistics and the required derivatives are provided to make computations feasible. An empirical example based on daily return series of five...

RELAP simulation and experimental verification of transient boiling conditions in narrow coolant channels, at low temperature and pressure

International Nuclear Information System (INIS)

Kunze, J.F.; Loyalka, S.K.; Hultsch, R.A.; Oladiran, O.; McKibben, J.C.

1990-01-01

This paper reports on benchmark experiments needed to verify the accuracy of thermal hydraulic codes (such as RELAP5/MOD2) with respect to their capability to simulate transient boiling conditions both with and without a closed recirculation path in narrow channels, under essentially atmospheric pressure conditions characteristic of plate-type research reactors. An experimental apparatus with this objective has been constructed, and data for surface heat flux of 1.2 x 10 5 w/m 2 are reported

Real-time corrosion monitoring of steel influenced by microbial activity (SRB) under controlled seawater injection conditions

Energy Technology Data Exchange (ETDEWEB)

Kane, Russell D. [InterCorr International, Inc., 14503 Bammel N. Houston Road, Suite 300, Houston, TX 77019 (United States); Campbell, Scott [Commercial Microbiology Inc., 10400 Westoffice Drive Suite 107, Houston, TX 77042 (United States)

2004-07-01

An experimental study of microbiologically influenced corrosion (MIC) was conducted involving online, real-time monitoring of a bio-film loop under controlled conditions simulating oil field water handling and injection. Bio-film growth, MIC and biocide efficacy were monitored using an automated, multi-technique monitoring system including linear polarization resistance, electrochemical noise and harmonic distortion analysis. This data was correlated with conventional off-line methods to differentiate conditions of varying MIC activity in real-time to facilitate quick assessment and operator intervention. (authors)

Perturbation methods and the Melnikov functions for slowly varying oscillators

International Nuclear Information System (INIS)

Lakrad, Faouzi; Charafi, Moulay Mustapha

2005-01-01

A new approach to obtaining the Melnikov function for homoclinic orbits in slowly varying oscillators is proposed. The present method applies the Lindstedt-Poincare method to determine an approximation of homoclinic solutions. It is shown that the resultant Melnikov condition is the same as that obtained in the usual way involving distance functions in three dimensions by Wiggins and Holmes [Homoclinic orbits in slowly varying oscillators. SIAM J Math Anal 1987;18(3):612

The Effectiveness of Experimental Diet with Varying Levels of Papain on The Growth Performance, Survival Rate and Feed Utilization of Keureling Fish (Tor tambra

Directory of Open Access Journals (Sweden)

Zainal Abidin Muchlisin

2016-09-01

Full Text Available The objective of present study was to determine the optimum level of papain in the diet of keureling fish (Tor tambra. The complete random design was utilized in this study. Six levels of papain dosage were tested in triplicates, i.e. 0 (control; 17.5 mg kg-1,  20.0 mg kg-1, 22.5 mg kg-1, 25.0 mg kg-1 and 27.5 mg kg-1 of feed. The experimental fish were fed the experimental diet two times a day at 8 AM and 5 PM at feeding level of 5% body weight for 90 days. The Anova test result showed that papain enzyme  gave a significant effect on the weight gain, daily growth rate, specific growth rate, survival rate, feed conversion ratio and feed efficiency (P<0.05. The Duncan multi-rage test result showed that the higher values for all measured parameters were obtained at the dosage of 27.5 mg kg-1. Therefore, it is concluded that the optimum dosage of papain enzyme for keureling fish was 27.5 mg kg-1 of feed.How to CiteMuchlisin, Z. A., Afrido, F., Murda, T., Fadli, N., Muhammadar, A. A., Jalil, Z., & Yulvizar, C. (2016. The Effectiveness of Experimental Diet with Varying Levels of Papain on The Growth Performance, Survival Rate and Feed Utilization of Keureling Fish (Tor tambra. Biosaintifika: Journal of Biology & Biology Education, 8(2, 172-177.

Demographic aspects of Chrysomya megacephala (Diptera, Calliphoridae) adults maintained under experimental conditions: reproductive rate estimates

OpenAIRE

Carvalho, Marcelo Henrique de; Von Zuben, Claudio José

2006-01-01

The objective of this work was to evaluate some aspects of the populational ecology of Chrysomya megacephala, analyzing demographic aspects of adults kept under experimental conditions. Cages of C. megacephala adults were prepared with four different larval densities (100, 200, 400 and 800). For each cage, two tables were made: one with demographic parameters for the life expectancy estimate at the initial age (e0), and another with the reproductive rate and average reproduction age estimates...

Radiation damage in stainless steel under varying temperature neutron irradiation

Energy Technology Data Exchange (ETDEWEB)

Yoshida, Naoaki [Kyushu Univ., Kasuga, Fukuoka (Japan). Research Inst. for Applied Mechanics

1998-03-01

Microstructural evolution of model alloys of 316SS was examined by neutron irradiation at JMTR under cyclic temperature varying condition. In the case of Fe-16Cr-17Ni, formation of interstitial loops and voids are strongly suppressed by varying the temperature from 473K to 673K. By adding Ti as miner element (0.25wt%), however, abnormal accumulation of vacancies (void swelling of 11%dpa at 0.1dpa) was observed. Theoretical analysis standing on the rate theory of defect clustering and simulation irradiation experiments with heavy ions indicates that the vacancy-rich condition which appears temporally during and after changing the temperature from low to high brings these results. It was also shown that only 1 dpa pre-irradiation at low temperature changes swelling behavior at high temperature above several 10 dpa. The understanding of non-steady-state defect processes under temperature varying irradiation is very important to estimate the radiation damage under fusion environment where short-term and long-term temperature variation is expected. (author)

Establishment and performance of an experimental green roof under extreme climatic conditions

Energy Technology Data Exchange (ETDEWEB)

Klein, Petra M., E-mail: pkklein@ou.edu [School of Meteorology, University of Oklahoma, Norman, OK (United States); Coffman, Reid, E-mail: rcoffma4@kent.edu [College of Architecture and Environmental Design, Kent State University, Kent, OH (United States)

2015-04-15

Green roofs alter the surface energy balance and can help in mitigating urban heat islands. However, the cooling of green roofs due to evapotranspiration strongly depends on the climatic conditions, and vegetation type and density. In the Southern Central Plains of the United States, extreme weather events, such as high winds, heat waves and drought conditions pose challenges for successful implementation of green roofs, and likely alter their standard performance. The National Weather Center Experimental Green Roof, an interdisciplinary research site established in 2010 in Norman, OK, aimed to investigate the ecological performance and surface energy balance of green roof systems. Starting in May 2010, 26 months of vegetation studies were conducted and the radiation balance, air temperature, relative humidity, and buoyancy fluxes were monitored at two meteorological stations during April–October 2011. The establishment of a vegetative community trended towards prairie plant dominance. High mortality of succulents and low germination of grasses and herbaceous plants contributed to low vegetative coverage. In this condition succulent diversity declined. Bouteloua gracilis and Delosperma cooperi showed typological dominance in harsh climatic conditions, while Sedum species experienced high mortality. The plant community diversified through volunteers such as Euphorbia maculate and Portulaca maculate. Net radiation measured at a green-roof meteorological station was higher than at a control station over the original, light-colored roofing material. These findings indicate that the albedo of the green roof was lower than the albedo of the original roofing material. The low vegetative coverage during the heat and drought conditions in 2011, which resulted in the dark substrate used in the green roof containers being exposed, likely contributed to the low albedo values. Nevertheless, air temperatures and buoyancy fluxes were often lower over the green roof indicating

Establishment and performance of an experimental green roof under extreme climatic conditions

International Nuclear Information System (INIS)

Klein, Petra M.; Coffman, Reid

2015-01-01

Green roofs alter the surface energy balance and can help in mitigating urban heat islands. However, the cooling of green roofs due to evapotranspiration strongly depends on the climatic conditions, and vegetation type and density. In the Southern Central Plains of the United States, extreme weather events, such as high winds, heat waves and drought conditions pose challenges for successful implementation of green roofs, and likely alter their standard performance. The National Weather Center Experimental Green Roof, an interdisciplinary research site established in 2010 in Norman, OK, aimed to investigate the ecological performance and surface energy balance of green roof systems. Starting in May 2010, 26 months of vegetation studies were conducted and the radiation balance, air temperature, relative humidity, and buoyancy fluxes were monitored at two meteorological stations during April–October 2011. The establishment of a vegetative community trended towards prairie plant dominance. High mortality of succulents and low germination of grasses and herbaceous plants contributed to low vegetative coverage. In this condition succulent diversity declined. Bouteloua gracilis and Delosperma cooperi showed typological dominance in harsh climatic conditions, while Sedum species experienced high mortality. The plant community diversified through volunteers such as Euphorbia maculate and Portulaca maculate. Net radiation measured at a green-roof meteorological station was higher than at a control station over the original, light-colored roofing material. These findings indicate that the albedo of the green roof was lower than the albedo of the original roofing material. The low vegetative coverage during the heat and drought conditions in 2011, which resulted in the dark substrate used in the green roof containers being exposed, likely contributed to the low albedo values. Nevertheless, air temperatures and buoyancy fluxes were often lower over the green roof indicating

Optimum Design of Multi-Function Robot Arm Gripper for Varying Shape Green Product

Directory of Open Access Journals (Sweden)

Razali Zol Bahri

2016-01-01

Full Text Available The project focuses on thorough experimentally studies of the optimum design of Multi-function Robot Arm Gripper for varying shape green product. The purpose of this project is to design a few of robot arm gripper for multi-functionally grip a green product with varying shape. The main character of the gripper is that it can automated adjust its finger to suit with the shape of the product. An optimum design of multi-function robot arm gripper is verified through experimental study. The expected result is a series of analytical results on the proposal of gripper design and material that will be selected for the gripper. The analysis of the gripper design proposal by using ANSYS and CATIA software is described in detail in this paper.

Experimental Investigation of Mechanical Properties of PVC Polymer under Different Heating and Cooling Conditions

Directory of Open Access Journals (Sweden)

Sarkawt Rostam

2016-01-01

Full Text Available Due to a widely increasing usage of polymers in various industrial applications, there should be a continuous need in doing research investigations for better understanding of their properties. These applications require the usage of the polymer in different working environments subjecting the material to various temperature ranges. In this paper, an experimental investigation of mechanical properties of polyvinyl chloride (PVC polymer under heating and cooling conditions is presented. For this purpose standard samples are prepared and tested in laboratory using universal material testing apparatus. The samples are tested under different conditions including the room temperature environment, cooling in a refrigerator, and heating at different heating temperatures. It is observed that the strength of the tested samples decreases with the increasing of heating temperature and accordingly the material becomes softer. Meanwhile the cooling environments give a clear increasing to the strength of the material.

An Experimental Study of Turbulent Nonpremixed Jet Flames in Crossflow Under Low-Gravity Conditions

Science.gov (United States)

Boxx, Isaac G.; Idicheria, Cherian A.; Clemens, Noel T.

2002-11-01

We will present results of a study of turbulent nonpremixed jet flames in crossflow under normal and low gravity conditions. This enables us to experimentally separate the competing influences of initial jet-to-crossflow momentum ratio and buoyancy effects on the flame structure. The low gravity conditions (10-30 milli-g) are achieved by dropping a self-contained jet flame rig in the University of Texas 1.25-second drop tower facility. This rig uses a small blow-through wind tunnel to create the crossflow. The jet flames issue from an orifice that is flush with the wall. High-speed CCD imaging of jet flame luminosity is the primary diagnostic. We present results for hydrocarbon jet flames with initial jet-to-crossflow momentum ratios of 10-20. Results such as flame trajectory, flame length, large scale structure and flame tip dynamics will be presented.

Experimental studies of an optimal operating condition for the Bunsen process in the I-S thermochemical cycle

International Nuclear Information System (INIS)

Yoon, Ho Joon; No, Hee Cheon; Kim, Young Soo; Jin, Hyung Gon; Lee, Jeong Ik; Lee, Byung Jin

2009-01-01

Conventional I-S cycles have critical limitations in material integrity and thermal efficiency. The HIx and sulfuric acids in high temperature and pressure cause serious material corrosions. They also carry too much water and iodine over the entire processes. To try to find a solution to these problems, KAIST proposed an optimal operating condition of Bunsen section through a parametric study of existing experimental data, and, based on it, devised a new flowsheet. When the contents of water and I 2 in the feed are controlled within the optimal band, HI concentration in HIx phase becomes strongly over-azeotropic. By simple flashing of the over-azeotropic HI solution, highly enriched HI vapor can be obtained, which leads to improved energy efficiency of the cycle. Since the cycle is operable under low pressures, the corrosivity of the operating condition can also be alleviated. In order to validate the previous experimental data and enhance the feasibility of the newly proposed flowsheet, KAIST is performing experiments. Procedure and results of early stage of experiments are introduced in this paper. (author)

Empirical Evidence on Time-Varying Hedging Effectiveness of Emissions Allowances under Departures from the Cost-of-Carry Theory

Directory of Open Access Journals (Sweden)

Kai Chang

2013-01-01

Full Text Available Under departures from the cost-of-carry theory, traded spot prices and conditional volatility disturbed from futures market have significant impacts on futures price of emissions allowances, and then we propose time-varying hedge ratios and hedging effectiveness estimation using ECM-GARCH model. Our empirical results show that conditional variance, conditional covariance, and their correlation between between spot and futures prices exhibit time-varying trends. Conditional volatility of spot prices, conditional volatility disturbed from futures market, and conditional correlation of market noises implied from spot and futures markets have significant effects on time-varying hedge ratios and hedging effectiveness. In the immature emissions allowances market, market participants optimize portfolio sizes between spot and futures assets using historical market information and then achieve higher risk reduction of assets portfolio revenues; accordingly, we can obtain better hedging effectiveness through time-varying hedge ratios with departures from the cost-of-carry theory.

Bedforms formed by experimental supercritical density flows

Science.gov (United States)

Naruse, Hajime; Izumi, Norihiro; Yokokawa, Miwa; Muto, Tetsuji

2014-05-01

This study reveals characteristics and formative conditions of bedforms produced by saline density flows in supercritical flow conditions, especially focusing on the mechanism of the formation of plane bed. The motion of sediment particles forming bedforms was resolved by high-speed cameras (1/1000 frame/seconds). Experimental density flows were produced by mixtures of salt water (1.01-1.04 in density) and plastic particles (1.5 in specific density, 140 or 240 mm in diameter). Salt water and plastic particles are analogue materials of muddy water and sand particles in turbidity currents respectively. Acrylic flume (4.0 m long, 2.0 cm wide and 0.5 m deep) was submerged in an experimental tank (6.0 m long, 1.8 m wide and 1.2 m deep) that was filled by clear water. Features of bedforms were observed when the bed state in the flume reached equilibrium condition. The experimental conditions range 1.5-4.2 in densimetric Froude number and 0.2-0.8 in Shields dimensionless stress. We report the two major discoveries as a result of the flume experiments: (1) Plane bed under Froude-supercritical flows and (2) Geometrical characteristics of cyclic steps formed by density flows. (1) Plane bed was formed under the condition of supercritical flow regime. In previous studies, plane bed has been known to be formed by subcritical unidirectional flows (ca. 0.8 in Froude number). However, this study implies that plane bed can also be formed by supercritical conditions with high Shields dimensionless stress (>0.4) and very high Froude number (> 4.0). This discovery may suggest that previous estimations of paleo-hydraulic conditions of parallel lamination in turbidites should be reconsidered. The previous experimental studies and data from high-speed camera suggest that the region of plane bed formation coincides with the region of the sheet flow developments. The particle transport in sheet flow (thick bedload layer) induces transform of profile of flow shear stress, which may be

A Question of Control? Examining the Role of Control Conditions in Experimental Psychopathology using the Example of Cognitive Bias Modification Research.

Science.gov (United States)

Blackwell, Simon E; Woud, Marcella L; MacLeod, Colin

2017-10-26

While control conditions are vitally important in research, selecting the optimal control condition can be challenging. Problems are likely to arise when the choice of control condition is not tightly guided by the specific question that a given study aims to address. Such problems have become increasingly apparent in experimental psychopathology research investigating the experimental modification of cognitive biases, particularly as the focus of this research has shifted from theoretical questions concerning mechanistic aspects of the association between cognitive bias and emotional vulnerability, to questions that instead concern the clinical efficacy of 'cognitive bias modification' (CBM) procedures. We discuss the kinds of control conditions that have typically been employed in CBM research, illustrating how difficulties can arise when changes in the types of research questions asked are not accompanied by changes in the control conditions employed. Crucially, claims made on the basis of comparing active and control conditions within CBM studies should be restricted to those conclusions allowed by the specific control condition employed. CBM studies aiming to establish clinical utility are likely to require quite different control conditions from CBM studies aiming to illuminate mechanisms. Further, conclusions concerning the clinical utility of CBM interventions cannot necessarily be drawn from studies in which the control condition has been chosen to answer questions concerning mechanisms. Appreciating the need to appropriately alter control conditions in the transition from basic mechanisms-focussed investigations to applied clinical research could greatly facilitate the translational process.

Experimental calibration and validation of sewer/surface flow exchange equations in steady and unsteady flow conditions

Science.gov (United States)

Rubinato, Matteo; Martins, Ricardo; Kesserwani, Georges; Leandro, Jorge; Djordjević, Slobodan; Shucksmith, James

2017-09-01

The linkage between sewer pipe flow and floodplain flow is recognised to induce an important source of uncertainty within two-dimensional (2D) urban flood models. This uncertainty is often attributed to the use of empirical hydraulic formulae (the one-dimensional (1D) weir and orifice steady flow equations) to achieve data-connectivity at the linking interface, which require the determination of discharge coefficients. Because of the paucity of high resolution localised data for this type of flows, the current understanding and quantification of a suitable range for those discharge coefficients is somewhat lacking. To fulfil this gap, this work presents the results acquired from an instrumented physical model designed to study the interaction between a pipe network flow and a floodplain flow. The full range of sewer-to-surface and surface-to-sewer flow conditions at the exchange zone are experimentally analysed in both steady and unsteady flow regimes. Steady state measured discharges are first analysed considering the relationship between the energy heads from the sewer flow and the floodplain flow; these results show that existing weir and orifice formulae are valid for describing the flow exchange for the present physical model, and yield new calibrated discharge coefficients for each of the flow conditions. The measured exchange discharges are also integrated (as a source term) within a 2D numerical flood model (a finite volume solver to the 2D Shallow Water Equations (SWE)), which is shown to reproduce the observed coefficients. This calibrated numerical model is then used to simulate a series of unsteady flow tests reproduced within the experimental facility. Results show that the numerical model overestimated the values of mean surcharge flow rate. This suggests the occurrence of additional head losses in unsteady conditions which are not currently accounted for within flood models calibrated in steady flow conditions.

Looking for carbonates in the deep Earth: an experimental approach at extreme conditions

Science.gov (United States)

Chariton, S.; Bykova, E.; Bykov, M.; Cerantola, V.; Vasiukov, D.; Stekiel, M.; Aprilis, G.; Kupenko, I.; Ismailova, L.; Chumakov, A. I.; Winkler, B.; McCammon, C. A.; Dubrovinsky, L. S.

2017-12-01

There is a long list of natural and experimental evidence to support a key role for carbonates in the deep carbon cycle. As potential carriers of carbon in subducted slabs with the possibility to influence redox conditions, carbonates have deservedly been the focus of many high pressure and high temperature experimental studies over the past decade. "How long do they survive after subduction? What form do they transform to? How do they react with their surroundings?" are all important questions. We use many tools to search for carbonates in the deep Earth. Using laser heated diamond anvil cells to generate pressures and temperatures over 100 GPa and 2500 K along with the advanced technology provided by synchrotron facilities, we have been able to study in situ the behavior of various carbonate minerals at conditions of the Earth's mantle. We have particularly focused our interest on transition metal carbonates (Fe, Mn, Co, Zn, Ni)CO3 in order to study the crystal chemistry of calcite-type carbonates using single crystal X-ray diffraction and Raman spectroscopy. Our results show new high-pressure carbonate structures, including either CO3-3or CO4-4 units, that often coexist with complex metal oxides. Combined with carbonate stability fields from the surface to the lower mantle, we investigated the possibility to detect carbonates from seismic data. We determined the elastic wave velocities of plausible carbonate mineral compositions in the (Mg-Fe)CO3 system using Nuclear Inelastic Scattering. Our results show the strong anisotropic behavior of carbonates that could explain anisotropic anomalies observed at transition zone depths and confirm the presence of carbonate reservoirs. The effect of carbonate composition and Fe2+ spin transition, which is completed above 50 GPa, are also well demonstrated. More new carbonate phases and their seismic signatures await to be discovered, and thus experiments continue.

Experimental studies of solar heat pipe used to operate absorption chiller in conditions of Vietnam

Energy Technology Data Exchange (ETDEWEB)

Hiep, Le Chi [Ho Chi Minh City Univ. of Tech., Ho Chi Minh City (Viet Nam); Quoc, Hoang An [Ho Chi Minh City Univ. of Tech. Education, Ho Chi Minh City (Viet Nam); Hung, Hoang Duong [Danang Univ. of Tech., Danang City (Viet Nam)

2008-07-01

Several models of solar heat pipe have been fabricated and tested. The experiments show that the flat plate model could be used to operate absorption chiller in the climate of southern part of Vietnam. Two main advantages of the selected solar heat pipe are low cost and easy fabrication at local conditions. It is expected that the selected solar heat pipe could attract attention of the community to develop the application of solar energy in Vietnam. Based on the current demand, the paper presents the experimental studies of the first generation of low cost solar heat pipe. The paper also discusses the ability of application of solar air conditioning in Vietnam and recommends the suitable diagram mixing solar energy with other heat source to operate stably the system. (orig.)

An experimental study on the two-phase natural circulation flow through the gap between reactor vessel and insulation under ERVC

Energy Technology Data Exchange (ETDEWEB)

Ha, Kwang-Soon; Park, Rae-Joon; Cho, Young-Ro; Kim, Sang-Baik; Kim, Hwan-Yeol; Kim, Hee-dong

2005-04-01

As part of a study on a two-phase natural circulation flow between the outer reactor vessel and the insulation material in the reactor cavity under an external reactor vessel cooling of APR1400, T-HERMES-SMALL and HERMES-HALF experiments have been performed. For the T-HERMES-SMALL experiments, an 1/21.6 scaled experimental facility was prepared utilizing the results of a scaling analysis to simulate the APR1400 reactor and insulation system. The liquid mass flow rates driven by natural circulation loop were measured by varying the wall heat flux, upper outlet area and configuration, and water head condition. The experimental data were also compared with numerical ones given by simple loop analysis. And non-heating small-scaled experiments have also been performed to certify the hydraulic similarity of the heating experiments by injecting air equivalent to the steam generated in the heating experimental condition. The HERMES-HALF experiment is a half-scaled / non-heating experimental study on the two-phase natural circulation through the annular gap between the reactor vessel and the insulation. The behaviors of the two-phase natural circulation flow in the insulation gap were observed, and the liquid mass flow rates driven by natural circulation loop were measured by varying the air injection rate, the coolant inlet area and configuration, and the outlet area and also the water head condition of coolant reservoir. From the experimental flow observation, the recirculation flows in the near region of the shear key were identified. At a higher air injection rate condition, higher recirculation flows and choking phenomenon in the near region of the shear key were observed. As the water inlet areas increased, the natural circulation mass flow rates asymptotically increased, that is, they converged at a specific value. And the experimental correlations for the natural circulation mass flow rates along with a variation of the inlet / outlet area and wall heat flux were

Experimental and numerical study on inlet and outlet conditions of a bulb turbine with considering free surface

International Nuclear Information System (INIS)

Zhao, Y P; Liao, W L; Feng, H D; Ruan, H; Luo, X Q

2012-01-01

For a bulb turbine, it has a low head and a big runner diameter, and the free surface influences the flow at the inlet and outlet of the turbine, which bring many problems such as vibration, cracks and cavitation to the turbine. Therefore, it is difficult to get the precise internal flow characteristics through a numerical simulation with conventional ideal flow conditions. In this paper, both numerical and experimental methods are adopted to investigate the flow characteristics at the inlet and outlet of the bulb turbine with considering free surface. Firstly, experimental and numerical studies in a low head pressure pipeline are conducted, and the corresponding boundary condition according with reality is obtained through the comparison between the model test result and the CFD simulation result. Then, through an analysis of the velocity and pressure fields at the inlet of the bulb turbine at different heads, the flow characteristics and rules at the entrance of the bulb turbine have been revealed with considering free surface; Finally, the performance predictions for a bulb turbine have been conducted by using the obtained flow rules at the inlet as the boundary condition of a turbine, and the causes that lead to non-uniform forces on blades, cavitation and vibration have been illustrated in this paper, which also provide a theory basis for an accurate numerical simulation and optimization design of a bulb turbine.

Experimental and theoretical investigations of Cs-Ba vapor tacitron inverter for power conditioning in space power systems

International Nuclear Information System (INIS)

El-Genk, M.; Murray, C.; Wernsman, B.

1993-01-01

The operation characteristics of the Cs-Ba tacitron as a switch are investigated experimentally in three modes: (a) breakdown mode, (b) I-V mode, and (c) current modulation mode. The switching frequency, grid potentials for ignition and extinguishing of discharge, and the Cs pressure and emission conditions (Ba pressure and emitter temperature) for stable current modulation are determined. The experimental data is also used to determine the off-time required for successful ignition, and the effects of the aforementioned operation parameters on the ignition duty cycle threshold for stable modulation. Operation parameters measured include switching frequency up to 20 kHz, hold-off voltage up to 180 V, current densities in excess of 15 A/cm 2 , switch power density of 1 kW/cm 2 . and a switching efficiency in excess of 90% at collector C: realer than 30 V. The voltage drop strongly depends on the Cs pressure and to a lesser extent on the emission conditions. Increasing the Cs pressure and/or the emission current lowers the voltage drop, however, for the same initial Cs pressure and emission conditions, the voltage drop in the I-V mode is usually lower than that during current modulation. As long as the discharge current is kept lower that the.emission current, the voltage drop during stable current modulation could be as low as 3 V

Development status of the experimental and numerical load analysis of package units CASTOR registered under drop test conditions

International Nuclear Information System (INIS)

Voelzer, Walter; Schaefer, Marc; Rumanus, Erkan; Liedtke, Ralph; Brehmer, Frank

2012-01-01

The mechanical integrity of package units CASTOR registered for a 9-m drop test under accident conditions has to be demonstrated according the requirements of IAEA among others. For reduction of the loads the containers have to be equipped with shock absorbers on the bottom and top sides. The determination of loads under drop test conditions can be performed with experimental or numerical methods. Due to the complexity of the load state and the verification of results both methods are usually used for integrity demonstration. The numerical codes have to model the short-term dynamic behavior of the whole container for different drop orientations and temperatures, local stress states have to be quantifiable for assessment. One of the problems is the modeling of the material behavior of wood that is used in the shock absorbers. The so far used energetic calculation approach will be replaced by a dynamic approach, the numerical models will have to be verified by experimental drop tests.

Effect of experimental conditions on the stability of Tc-99m radiopharmaceuticals

International Nuclear Information System (INIS)

Vucina, J.

2002-01-01

The stability of three 99m Tc radiopharmaceuticals in dependence on the experimental conditions and on the presence of some chemical stabiliser was tested. Examined were dimercapto succinate (DMS), pyrophosphate (PyP) and 2,3-dicarboxypropane-1,1-diphosphonate (DPD). The reliability and applicability of the preparation of the three radiopharmaceuticals from the inactive (technetium-cold) kit solutions were tested. Each kit was dissolved in saline (0.9% NaCl). The storage conditions of the inactive kit solutions before labelling were determined. The main problem is the stability of the reductant stannous ions which is very difficult to predict. Ascorbic or gentisic acid was added in order to stabilise the labelled radiopharmaceuticals and ensure their good quality. The best results were obtained by keeping the samples at -20 deg C. Although either stabiliser can be used, much lower concentrations of ascorbic acid are sufficient for an effective protection. Its concentrations of 12-60 μg/ml of the kit stabilise DMS and PyP for about 7-8 days. The solution of DPD was stable even without any stabiliser, presumably dut to the chemical nature of this complex. In routine practice, however, the procedure requires caution, and the staff should be very experienced in radiopharmacy procedures

Type of activity and order of experimental conditions affect noise annoyance by identifiable and unidentifiable transportation noise.

Science.gov (United States)

White, Kim; Bronkhorst, Adelbert W; Meeter, Martijn

2018-04-01

Previous studies have shown that identifiability of sound sources influence noise annoyance levels. The aim of the present experiment was to additionally study the effects of actively performing a task versus a less active pastime on noise annoyance. This was done by asking participants to perform a task (task condition) or read a magazine of their choice (no-task condition), while listening to identifiable and unidentifiable samples of transportation noise at varying sound exposure levels (55-85 ASEL). Annoyance was higher for identifiable samples (recordings) than for unidentifiable transformed samples (with equal spectral energy and envelope). Although there was no main effect of activity type on noise annoyance, for the transformed samples, an interaction was found between activity type and sound exposure levels: annoyance started lower in the no-task condition, but rose more steeply with ascending exposure levels than was the case during task performance (large effect). When assessing order effects, it was found that annoyance was higher when the task condition came first, especially for lower sound exposure levels (large effects). It is therefore concluded that the type of activity and the condition order do influence noise annoyance but in interaction with exposure levels, the type of noise and habituation.

Experimental identification of pedestrian-induced lateral forces on footbridges

DEFF Research Database (Denmark)

Ingólfsson, Einar Thór; Georgakis, Christos; Ricciardelli, Francesco

2011-01-01

combinations of frequencies (0.33-1.07 Hz) and amplitudes 4.5-48 mm). The experimental campaign involved seventy-one male and female human adults and covered approximately 55 km of walking distributed between 4954 individual tests. When walking on a laterally moving surface, motion-induced forces develop also......This paper presents a comprehensive experimental analysis of lateral forces generated by single pedestrians during continuous walking on a treadmill. Two different conditions are investigated; initially the treadmill is fixed and then it is laterally driven in a sinusoidal motion at varying...... and inter-subject variability. It is shown that the motion induced portion of the pedestrian load (on average) inputs energy into the structure in the frequency range (normalised by the average walking frequency) between approximately 0.6 and 1.2. Furthermore, it is shown that the load component in phase...

Effects of Varying RedoxConditions on Natural Attenuation of Inorganic Contaminants from the D-Area Coal Pile Runoff Basin (U)

Energy Technology Data Exchange (ETDEWEB)

Kaplan, D

2004-05-30

The objective of this study was to provide geochemical parameters to characterize the D-Area Coal Pile Runoff Basin (DCPRB) sediment as a potential source term. It is anticipated that the measured values will be used in risk calculations and will provide additional technical support for imposing Monitored Natural Attenuation at D-Area. This study provides a detailed evaluation of the DCPRB sediment and is part of another study that quantified the Monitored Natural Attenuation of inorganic contaminants more broadly at the D-Area Expanded Operable Unit, which includes the DCPRB (Powell et al. 2004). Distribution coefficients (K{sub d} values; a solid to liquid contaminant concentration ratio) and the Potentially Leachable Fraction (the percent of the total contaminant concentration in the sediment that can likely contribute to a contaminant plume) were measured in a DCPRB sediment as a function of redox conditions. Redox conditions at the DCPRB are expected to vary greatly as the system undergoes varying drying and flooding conditions. Conservative values; K{sub d} values that err on the side of being too low and Potentially Leachable Fraction values that err on the side of being too high, are presented. The K{sub d} values are high compared to conservative literature values, and underscores the importance of measuring site-specific values to provide estimates of sediments natural attenuation/sorption capacities. The Potentially Leachable Fraction indicates that as little as 27% of the As, but all of the Cu and Tl will be part of the source term. In the case of the As, the remaining 83% will likely never leach out of the sediment, thereby providing a form of natural attenuation. Importantly, Be, Cr, Cu, Ni, and V concentrations in the sediment were less-than twice background levels, indicating this sediment was not a potential source for these contaminants. K{sub d} values generally increased significantly (As, Cd, Co, Cr, Cu, Ni, Se, and Tl) when the sediment was

Experimental assessment of an absorption cooling system operating with the ammonia/lithium nitrate mixture

International Nuclear Information System (INIS)

Hernández-Magallanes, J.A.; Domínguez-Inzunza, L.A.; Gutiérrez-Urueta, G.; Soto, P.; Jiménez, C.; Rivera, W.

2014-01-01

This paper reports the experimental results of a single effect absorption cooling system of 3 kW of nominal cooling capacity operating with ammonia–lithium nitrate solution. The system was designed and built in the Instituto de Energías Renovables of the Universidad Nacional Autónoma de México and can be used for food conservation or air conditioning. The absorber and generator are falling film heat exchangers. The condenser, evaporator and solution heat exchanger are compact plate heat exchangers. The heat was supplied to the generator at temperatures between 85 °C and 105 °C, while the cooling water temperatures to remove the heat produced during the condensation and absorption varied between 18 °C and 36 °C. The results showed that the system can produce up to 2.7 kW of cooling capacity at heating water temperatures of 95 °C and can achieve evaporator temperatures as low as 1 °C. The experimental coefficients of performance varied between 0.45 and 0.70. Because of the developed system do not need a rectifier and reasonable good coefficients of performance were achieved, the developed system seems to be a good alternative to be used for food conservation or air conditioning. - Highlights: • An absorption cooling system was developed using NH 3 –LiNO 3 . • The achieved COP (coefficients of performance) are the highest reported for a system using NH 3 –LiNO 3 . • Evaporator temperatures as low as 1 °C were achieved. • COP varied between 0.45 and 0.7. • The developed system seems to be a good alternative for food conservation and air conditioning

Simulation and experimental study of a solar heat pump desalination system

Energy Technology Data Exchange (ETDEWEB)

Hawlader, M.N.A.; Tjandra, Tobias Bestari [Dept. of Mechanical Engineering, National Univ. of Singapore, Singapore (Singapore)

2008-07-01

With the rising price of oil and gas, the energy cost of desalination process increases significantly. Also, the consumption of fuel to provide thermal and electrical energy in a desalination process will pollute the environment. Therefore, it is necessary to find a new source of energy which is clean and renewable. Solar energy fulfills this challenge to a great extent. An experimental rig was constructed in order to investigate the use of solar energy in desalination. A series of experiments were performed under the meteorological conditions of Singapore. A simulation study was then performed for the system, and comparisons of the predicted and experimental results showed good agreement. The experimental system is capable of producing 1 liter of water per hour. The system has a coefficient of performance that varies from 5 to 9, and a performance ratio of 0.6 to 1.38. (orig.)

Cluster dynamics modeling and experimental investigation of the effect of injected interstitials

Science.gov (United States)

Michaut, B.; Jourdan, T.; Malaplate, J.; Renault-Laborne, A.; Sefta, F.; Décamps, B.

2017-12-01

The effect of injected interstitials on loop and cavity microstructures is investigated experimentally and numerically for 304L austenitic stainless steel irradiated at 450 °C with 10 MeV Fe5+ ions up to about 100 dpa. A cluster dynamics model is parametrized on experimental results obtained by transmission electron microscopy (TEM) in a region where injected interstitials can be safely neglected. It is then used to model the damage profile and study the impact of self-ion injection. Results are compared to TEM observations on cross-sections of specimens. It is shown that injected interstitials have a significant effect on cavity density and mean size, even in the sink-dominated regime. To quantitatively match the experimental data in the self-ions injected area, a variation of some parameters is necessary. We propose that the fraction of freely migrating species may vary as a function of depth. Finally, we show that simple rate theory considerations do not seem to be valid for these experimental conditions.

Equilibrium phase experimental determination of petroleum + gas systems at supercritical condition using ultrasonic technology; Estudo experimental do equilibrio de fases de sistemas de fracoes de petroleo e gases em condicoes supercriticas utilizando tecnicas de ultra-som: aparato experimental

Energy Technology Data Exchange (ETDEWEB)

Mehl, Ana; Pessoa, Fernando L.P.; Silva, Silvia M.C. da [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Quimica; Feiteira, Jose F. [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Escola de Engenharia

2008-07-01

In separation process of multicomponent systems based on phase equilibrium is essential know the phase behavior and the critical points of the system for determination and optimization of the operational conditions. The experimental apparatus presents the challenge of determine the equilibrium phase dates of a system composed by petroleum residua and supercritical solvent. The used method, named acoustic method, allows the composition identification of the phases in equilibrium also in cloudy systems as they are the systems formed by residues of crude oil. For this reason, the acoustic methodology, based on the ultra-sound technology will be used in the study of the phase equilibrium and experimental characterization of the system, in benches scale, operating in severe conditions of temperature and pressure.The acoustic method is one not invasive and not subjective technique, what becomes the work in high pressures safer. (author)

Local conditions and uncertainty bands for Semiscale Test S-02-9

International Nuclear Information System (INIS)

Varacalle, D.J. Jr.

1979-01-01

Analysis was performed to derive local conditions heat transfer parameters and their uncertainties using computer codes and experimentally derived boundary conditions for the Semiscale core for LOCA Test S-02-9. Calculations performed consisted of nominal code cases using best-estimate input parameters and cases where the specified input parameters were perturbed in accordance with the response surface method of uncertainty analysis. The output parameters of interest were those that are used in film boiling heat transfer correlations including enthalpy, pressure, quality, and coolant flow rate. Large uncertainty deviations occurred during low core mass flow periods where the relative flow uncertainties were large. Utilizing the derived local conditions and their associated uncertainties, a study was then made which showed the uncertainty in film boiling heat transfer coefficient varied between 5 and 250%

Experimental device for investigating the crack growth behaviour of RPV steel under BWR conditions

International Nuclear Information System (INIS)

Anders, D.; Ahlf, J.

1983-01-01

An experimental device is developed to investigate the crack growth behaviour of RPV steel specimens under service conditions. It will be installed in the experimental power station VAK-Kahl (BWR, 16 MWe). The in pile part is composed of a stable frame with a hydraulically actuated load mechanism, the specimen chain and a measuring instrumentation. The specimen chain, fastened between load mechanism and a lower fixing point at the frame, is made up of five compact tensile specimens (CT40) and the associated connecting links. Specimen strain, crack opening and temperature are measured; for neutron dose monitoring activation wires are disposed. Out of pile, in the reactor hall, the hydraulic loading system is installed. The loading force is generated by a 100 kN-material testing machine; it moves a piston in the control cylinder, which is connected to the loading bellows of the in pile section. The measuring and control equipment and a desk computer serving for data preparation and reduction is placed in the reactor control room. (Auth.)

Detection of respiratory viruses in shelter dogs maintained under varying environmental conditions

Directory of Open Access Journals (Sweden)

Francielle Liz Monteiro

Full Text Available Abstract Three dog shelters in Rio Grande do Sul were investigated for associations between the occurrence of respiratory viruses and shelter environmental conditions. Nasal secretions randomly collected during the cold season were tested via PCR, and this data collection was followed by nucleotide sequencing of the amplicons. In shelter #1 (poor sanitary and nutritional conditions, high animal density and constant contact between dogs, 78% (58/74 of the nasal samples were positive, 35% (26/74 of which were in single infections and 44% (32/74 of which were in coinfections. Shelters #2 and #3 had satisfactory sanitary and nutritional conditions, outdoors exercise areas (#2 and animal clustering by groups (#3. In shelter #2, 9% (3/35 of the samples were positive for Canine parainfluenza virus (CPIV, and 6% (2/35 were positive for Canid herpesvirus 1 (CaHV-1. In shelter #3, 9% (7/77 of the samples were positive for Canine adenovirus type 2 (CAdV-2, and 1% (1/77 were positive for Canine distemper virus (CDV. The amplicon sequences (CPIV and CDV nucleoprotein gene; CAdV-2 E3 gene; CaHV-1 glycoprotein B gene showed 94-100% nucleotide identity with GenBank sequences. Our results demonstrate that CPIV, CAdV-2 and CDV are common in dog shelters and that their frequencies appear to be related with environmental and nutritional conditions. These results indicate the need for control/prevention measures, including vaccination and environmental management, to minimize these infections and improve dog health.

Comparison of computer code calculations with experimental results obtained in the NSPP series of experiments

International Nuclear Information System (INIS)

Tobias, M.L.

1987-01-01

Experiments were done on several aerosols in air atmospheres at varying temperatures and humidity conditions of interest in forming a data base for testing aerosol behavior models used as part of the process of evaluating the ''source term'' in light water reactor accidents. This paper deals with the problems of predicting the observed experimental data for suspended aerosol concentration with aerosol calculational codes. Comparisons of measured versus predicted data are provided

In-situ Condition Monitoring of Components in Small Modular Reactors Using Process and Electrical Signature Analysis. Final report, volume 1. Development of experimental flow control loop, data analysis and plant monitoring

Energy Technology Data Exchange (ETDEWEB)

Upadhyaya, Belle [Univ. of Tennessee, Knoxville, TN (United States); Hines, J. Wesley [Univ. of Tennessee, Knoxville, TN (United States); Damiano, Brian [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Mehta, Chaitanya [Univ. of Tennessee, Knoxville, TN (United States); Collins, Price [Univ. of Tennessee, Knoxville, TN (United States); Lish, Matthew [Univ. of Tennessee, Knoxville, TN (United States); Cady, Brian [Univ. of Tennessee, Knoxville, TN (United States); Lollar, Victor [Univ. of Tennessee, Knoxville, TN (United States); de Wet, Dane [Univ. of Tennessee, Knoxville, TN (United States); Bayram, Duygu [Univ. of Tennessee, Knoxville, TN (United States)

2015-12-15

plant parameters and the pump electrical signatures. Additionally, the reactor simulation is being used to generate normal operation data and data with instrumentation faults and process anomalies. A frequency controller was interfaced with the motor power supply in order to vary the electrical supply frequency. The experimental flow control loop was used to generate operational data under varying motor performance characteristics. Coolant leakage events were simulated by varying the bypass loop flow rate. The accuracy of motor power calculation was improved by incorporating the power factor, computed from motor current and voltage in each phase of the induction motor.- A variety of experimental runs were made for steady-state and transient pump operating conditions. Process, vibration, and electrical signatures were measured using a submersible pump with variable supply frequency. High correlation was seen between motor current and pump discharge pressure signal; similar high correlation was exhibited between pump motor power and flow rate. Wide-band analysis indicated high coherence (in the frequency domain) between motor current and vibration signals. - Wide-band operational data from a PWR were acquired from AMS Corporation and used to develop time-series models, and to estimate signal spectrum and sensor time constant. All the data were from different pressure transmitters in the system, including primary and secondary loops. These signals were pre-processed using the wavelet transform for filtering both low-frequency and high-frequency bands. This technique of signal pre-processing provides minimum distortion of the data, and results in a more optimal estimation of time constants of plant sensors using time-series modeling techniques.

In-situ Condition Monitoring of Components in Small Modular Reactors Using Process and Electrical Signature Analysis. Final report, volume 1. Development of experimental flow control loop, data analysis and plant monitoring

International Nuclear Information System (INIS)

Upadhyaya, Belle; Hines, J. Wesley; Damiano, Brian; Mehta, Chaitanya; Collins, Price; Lish, Matthew; Cady, Brian; Lollar, Victor; De Wet, Dane; Bayram, Duygu

2015-01-01

plant parameters and the pump electrical signatures. Additionally, the reactor simulation is being used to generate normal operation data and data with instrumentation faults and process anomalies. A frequency controller was interfaced with the motor power supply in order to vary the electrical supply frequency. The experimental flow control loop was used to generate operational data under varying motor performance characteristics. Coolant leakage events were simulated by varying the bypass loop flow rate. The accuracy of motor power calculation was improved by incorporating the power factor, computed from motor current and voltage in each phase of the induction motor.- A variety of experimental runs were made for steady-state and transient pump operating conditions. Process, vibration, and electrical signatures were measured using a submersible pump with variable supply frequency. High correlation was seen between motor current and pump discharge pressure signal; similar high correlation was exhibited between pump motor power and flow rate. Wide-band analysis indicated high coherence (in the frequency domain) between motor current and vibration signals. - Wide-band operational data from a PWR were acquired from AMS Corporation and used to develop time-series models, and to estimate signal spectrum and sensor time constant. All the data were from different pressure transmitters in the system, including primary and secondary loops. These signals were pre-processed using the wavelet transform for filtering both low-frequency and high-frequency bands. This technique of signal pre-processing provides minimum distortion of the data, and results in a more optimal estimation of time constants of plant sensors using time-series modeling techniques.

A new time-varying harmonic decomposition structure based on recursive hanning window

NARCIS (Netherlands)

Martins, C.H.; Silva, L.R.M.; Duque, C.A.; Cerqueira, A.S.; Teixeira, E.C.; Ribeiro, P.F.

2012-01-01

Analysis of power quality phenomena under time-varying conditions has become an important subject as the complexity of the grid increases. As a consequence, several methods have been developed/applied also to study power quality parameters during transient conditions such as time-frequency methods.

Metabolic Desynchronization in Critical Conditions: Experimental Study

Directory of Open Access Journals (Sweden)

G. V. Livanov

2006-01-01

Full Text Available Objective. To conduct an experimental study of the impact of the time of administration of succinic acid preparations on central nervous system (CNS function and gas exchange while simulating metabolic therapy for severe poisoning by ethyl alcohol. The study was performed on 74 male albino rats weighing 140—180 g. Acute severe and very severe intoxication was simulated, by intraabdominally administering 30% ethanol to the rats. Cytoflavin was used to simulate experimental therapy. The rate of gas exchange was estimated by the oxygen uptake determined by the closed chamber method in a Regnault apparatus (Germany. Spontaneous bioelectrical activity was recorded in the frontooccipital lead by the routine procedure. External pain stimulation and rhythmical photostimulation were employed to evaluate cerebral responsiveness. Heterodirectional EEG changes in the «early» and «late» administration of succinate were not followed by the similar alterations of gas exchange: oxygen consumption in both the «early» and «late» administration of succinate remained significantly lower than in the control animals. With the late administration of succinate to the animals with mixed (toxic and hypoxic coma, the so-called discrepancy between the noticeably increased energy production and brutally diminished metabolism occurred. It may be just the pathological mechanism that was the basis for higher mortality in the late succinate administration group. The findings and their analysis make it possible to advance a hypothesis that succinate may cause metabolic desynchronization if activation of metabolic processes takes place under severe tissue respiratory tissue depression. In these cases, there is a severe damage to tissue and chiefly the brain. This manifests itself as EEG epileptiform activity splashes preceding the animals’ death. Therefore, resuscitation aimed at restoring the transport of oxygen and its involvement in tissue energy processes should

Time-varying parameter models for catchments with land use change: the importance of model structure

Science.gov (United States)

Pathiraja, Sahani; Anghileri, Daniela; Burlando, Paolo; Sharma, Ashish; Marshall, Lucy; Moradkhani, Hamid

2018-05-01

Rapid population and economic growth in Southeast Asia has been accompanied by extensive land use change with consequent impacts on catchment hydrology. Modeling methodologies capable of handling changing land use conditions are therefore becoming ever more important and are receiving increasing attention from hydrologists. A recently developed data-assimilation-based framework that allows model parameters to vary through time in response to signals of change in observations is considered for a medium-sized catchment (2880 km2) in northern Vietnam experiencing substantial but gradual land cover change. We investigate the efficacy of the method as well as the importance of the chosen model structure in ensuring the success of a time-varying parameter method. The method was used with two lumped daily conceptual models (HBV and HyMOD) that gave good-quality streamflow predictions during pre-change conditions. Although both time-varying parameter models gave improved streamflow predictions under changed conditions compared to the time-invariant parameter model, persistent biases for low flows were apparent in the HyMOD case. It was found that HyMOD was not suited to representing the modified baseflow conditions, resulting in extreme and unrealistic time-varying parameter estimates. This work shows that the chosen model can be critical for ensuring the time-varying parameter framework successfully models streamflow under changing land cover conditions. It can also be used to determine whether land cover changes (and not just meteorological factors) contribute to the observed hydrologic changes in retrospective studies where the lack of a paired control catchment precludes such an assessment.

Time-varying parameter models for catchments with land use change: the importance of model structure

Directory of Open Access Journals (Sweden)

S. Pathiraja

2018-05-01

Full Text Available Rapid population and economic growth in Southeast Asia has been accompanied by extensive land use change with consequent impacts on catchment hydrology. Modeling methodologies capable of handling changing land use conditions are therefore becoming ever more important and are receiving increasing attention from hydrologists. A recently developed data-assimilation-based framework that allows model parameters to vary through time in response to signals of change in observations is considered for a medium-sized catchment (2880 km2 in northern Vietnam experiencing substantial but gradual land cover change. We investigate the efficacy of the method as well as the importance of the chosen model structure in ensuring the success of a time-varying parameter method. The method was used with two lumped daily conceptual models (HBV and HyMOD that gave good-quality streamflow predictions during pre-change conditions. Although both time-varying parameter models gave improved streamflow predictions under changed conditions compared to the time-invariant parameter model, persistent biases for low flows were apparent in the HyMOD case. It was found that HyMOD was not suited to representing the modified baseflow conditions, resulting in extreme and unrealistic time-varying parameter estimates. This work shows that the chosen model can be critical for ensuring the time-varying parameter framework successfully models streamflow under changing land cover conditions. It can also be used to determine whether land cover changes (and not just meteorological factors contribute to the observed hydrologic changes in retrospective studies where the lack of a paired control catchment precludes such an assessment.

Theoretical model and experimental validation of a direct-expansion solar assisted heat pump for domestic hot water applications

International Nuclear Information System (INIS)

Moreno-Rodríguez, A.; González-Gil, A.; Izquierdo, M.; Garcia-Hernando, N.

2012-01-01

This paper has shown the development of a theoretical model to determine the operating parameters and consumption of a domestic hot water (DHW) installation, which uses a direct-expansion solar assisted heat pump (DXSAHP) with refrigerant R-134a, a compressor with a rated capacity of 1.1 kW and collectors with a total area of 5.6 m 2 . The model results have been compared and validated the experimental results obtained with the equipment installed at the University Carlos III, South of Madrid. The analysis was conducted over the course of a year, and the results have been represented depending on the meteorological and process variables of several representative days. Taking into account the thermal losses of the installation and the dependency on the operating conditions, the acquired experimental coefficient of performance is between 1.7 and 2.9, while the DHW tank temperature over the course of the study is 51 °C. -- Highlights: ► The study aims to present a new theoretical model and an experimental validation. ► The experimental COP vary between 1.7 and 2.9 (max. condensation temperature 57 °C). ► The operating parameters respond to the solar radiation. The COP may increase up to 50%. ► The useful surface area varies between 50% and 85% of the total surface. ► The system stops if conditions exceed the maximum value of the absorbed heat.

An Ice Track Equipped with Optical Sensors for Determining the Influence of Experimental Conditions on the Sliding Velocity

Science.gov (United States)

Lungevics, J.; Jansons, E.; Gross, K. A.

2018-02-01

The ability to slide on ice has previously focused on the measurement of friction coefficient rather than the actual sliding velocity that is affected by it. The performance can only be directly measured by the sliding velocity, and therefore the objective was to design and setup a facility to measure velo-city, and determine how experimental conditions affect it. Optical sensors were placed on an angled ice track to provide sliding velocity measurements along three sections and the velocity for the total sliding distance. Experimental conditions included the surface roughness, ambient temperature and load. The effect of roughness was best reported with a Criterion of Contact that showed a similar sliding velocity for metal blocks abraded with sand paper smoother than 600 grit. Searching for the effect of temperature, the highest sliding velocity coincided with the previously reported lowest coefficient of ice friction. Load showed the greatest velocity increase at temperatures closer to the ice melting point suggesting that in such conditions metal block overcame friction forces more easily than in solid friction. Further research needs to be conducted on a longer ice track, with larger metal surfaces, heavier loads and higher velocities to determine how laboratory experiments can predict real-life situations.

An Ice Track Equipped with Optical Sensors for Determining the Influence of Experimental Conditions on the Sliding Velocity

Directory of Open Access Journals (Sweden)

Lungevics J.

2018-02-01

Full Text Available The ability to slide on ice has previously focused on the measurement of friction coefficient rather than the actual sliding velocity that is affected by it. The performance can only be directly measured by the sliding velocity, and therefore the objective was to design and setup a facility to measure velo-city, and determine how experimental conditions affect it. Optical sensors were placed on an angled ice track to provide sliding velocity measurements along three sections and the velocity for the total sliding distance. Experimental conditions included the surface roughness, ambient temperature and load. The effect of roughness was best reported with a Criterion of Contact that showed a similar sliding velocity for metal blocks abraded with sand paper smoother than 600 grit. Searching for the effect of temperature, the highest sliding velocity coincided with the previously reported lowest coefficient of ice friction. Load showed the greatest velocity increase at temperatures closer to the ice melting point suggesting that in such conditions metal block overcame friction forces more easily than in solid friction. Further research needs to be conducted on a longer ice track, with larger metal surfaces, heavier loads and higher velocities to determine how laboratory experiments can predict real-life situations.

Bearing Condition Recognition and Degradation Assessment under Varying Running Conditions Using NPE and SOM

Directory of Open Access Journals (Sweden)

Shaohui Zhang

2014-01-01

Full Text Available Manifold learning methods have been widely used in machine condition monitoring and fault diagnosis. However, the results reported in these studies focus on the machine faults under stable loading and rotational speeds, which cannot interpret the practical machine running. Rotating machine is always running under variable speeds and loading, which makes the vibration signal more complicated. To address such concern, the NPE (neighborhood preserving embedding is applied for bearing fault classification. Compared with other algorithms (PCA, LPP, LDA, and ISOP, the NPE performs well in feature extraction. Since the traditional time domain signal denoising is time consuming and memory consuming, we denoise the signal features directly in feature space. Furthermore, NPE and SOM (self-organizing map are combined to assess the bearing degradation performance. Simulation and experiment results validate the effectiveness of the proposed method.

Investigation of Focusing Effect according to the Cooling Condition and Height of the Metallic layer in a Severe Accident

Energy Technology Data Exchange (ETDEWEB)

Moon, Je-Young; Chung, Bum-Jin [Kyung Hee University, Yongin (Korea, Republic of)

2015-05-15

The Fukushima nuclear power plant accident has led to renewed research interests in severe accidents of nuclear power plants. In-Vessel Retention (IVR) of core melt is one of key severe accident management strategies adopted in nuclear power plant design. The metallic layer is heated from below by the radioactive decay heat generated at the oxide pool, and is cooled from above and side walls. During the IVR process, reactor vessel may be cooled externally (ERVC) and the heat fluxes to the side wall increase with larger temperature difference than above. This {sup F}ocusing effect{sup i}s varied by cooling condition of upper boundary and height of the metallic layer. A sulfuric acid–copper sulfate (H{sub 2}SO{sub 4} - CuSO{sub 4}) electroplating system was adopted as the mass transfer system. Numerical analysis using the commercial CFD program FLUENT 6.3 were carried out with the same material properties and cooling conditions to examine the variation of the cell. The experimental and numerical studies were performed to investigate the focusing effect according to cooling condition of upper boundary and the height in metallic layer. The height of the side wall was varied for three different cooling conditions: top only, side only, and both top and side. Mass transfer experiments, based on the analogy concept, were carried out in order to achieve high Rayleigh number. The experimental results agreed well with the Rayleigh-Benard convection correlations of Dropkin and Somerscales and Globe and Dropkin. The heat transfer on side wall cooling condition without top cooling is highest and was enhanced by decreasing the aspect ratio. The numerical results agreed well with the experimental results. Each cell pattern (cell size, cell direction, central location of cell) differed in the cooling condition. Therefore, it is difficult to predict the internal flow due to complexity of cell formation behavior.

Experimental study of critical heat flux enhancement with hypervapotron structure under natural circulation conditions

Energy Technology Data Exchange (ETDEWEB)

Hou, Fangxin [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing (China); Chang, Huajian [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing (China); State Nuclear Power Technology R& D Center (Beijing), Beijing (China); Zhao, Yufeng, E-mail: zhaoyufeng@snptc.com.cn [State Nuclear Power Technology R& D Center (Beijing), Beijing (China); Zhang, Ming; Gao, Tianfang [State Nuclear Power Technology R& D Center (Beijing), Beijing (China); Chen, Peipei [State Power Investment Corporation, Beijing (China)

2017-05-15

Highlights: • Natural circulation tests are performed to study the effect of hypervapotron on CHF. • Hypervapotron structure improves CHF under natural circulation conditions. • Visualization data illustrate vapor blanket behavior under subcooled flow conditions. - Abstract: The enhancement of critical heat flux with a hypervapotron structure under natural circulation conditions is investigated in this study. Subcooled flow boiling CHF experiments are performed using smooth and hypervapotron surfaces at different inclination angles under natural circulation conditions. The experimental facility, TESEC (Test of External Vessel Surface with Enhanced Cooling), is designed to conduct CHF experiments in a 30 mm by 61 mm rectangular flow channel with a 200 mm long heated surface along the flow direction. The two-phase flow of subcooled flow boiling on both smooth and hypervapotron heating plates is observed and analyzed by the high-speed visualization technology. The results show that both smooth surface and hypervapotron surface CHF data exhibit a similar trend against inclination angles compared with the CHF results under forced flow condition on the same facility in earlier studies. However, the CHF enhancement of the hypervapotron structure is evidently more significant than the one under forced flow conditions. The experiments also indicate that the natural flow rates are higher with hypervapotron structure. The initiation of CHF is analyzed under transient subcooling and flow rate conditions for both smooth and hypervapotron heating surfaces. An explanation is given for the significant enhancement effect caused by the hypervapotron surface under natural circulation conditions. The visualization data are exhibited to demonstrate the behavior of the vapor blanket at various inclination angles and on different surfaces. The geometric data of the vapor blanket are quantified by an image post-processing method. It is found that the thickness of the vapor blanket

Conditional cooperation and confusion in public-goods experiments.

Science.gov (United States)

Burton-Chellew, Maxwell N; El Mouden, Claire; West, Stuart A

2016-02-02

Economic experiments are often used to study if humans altruistically value the welfare of others. A canonical result from public-good games is that humans vary in how they value the welfare of others, dividing into fair-minded conditional cooperators, who match the cooperation of others, and selfish noncooperators. However, an alternative explanation for the data are that individuals vary in their understanding of how to maximize income, with misunderstanding leading to the appearance of cooperation. We show that (i) individuals divide into the same behavioral types when playing with computers, whom they cannot be concerned with the welfare of; (ii) behavior across games with computers and humans is correlated and can be explained by variation in understanding of how to maximize income; (iii) misunderstanding correlates with higher levels of cooperation; and (iv) standard control questions do not guarantee understanding. These results cast doubt on certain experimental methods and demonstrate that a common assumption in behavioral economics experiments, that choices reveal motivations, will not necessarily hold.

Influence of experimental parameters on the microencapsulation of a photopolymerizable phase.

Science.gov (United States)

Pernot, J M; Brun, H; Pouyet, B; Sergent, M; Phan-Tan-Luu, R

1993-01-01

Conditions of microencapsulation by in situ polycondensation, using melamine-formaldehyde as wall material, are influenced by the chemical nature of the core to encapsulate. In our study concerning the encapsulation of a photopolymerizable phase containing an electrically charged compound, it was necessary to modify the experimental process to obtain capsules of good quality. We used the factorial design method of screening by utilization of an asymmetric matrix, according to the collapsing principle of Addleman. The advantage of this method is that it allows determination of the simultaneous influences of the 11 experimental parameters involved in this preparation. The calculation method can be applied to more than two levels for some of the factors. The continuously varying parameters were altered between two extreme levels, chosen to allow encapsulation. For discontinuous factors, such as the molecular weight of the modifying system or nature of the aminoplast, we used the commercially available compounds, respectively three and four kinds. The results of the obtained capsules were determined by comparing microphotographic pictures. With 16 experiments we found four more factors influencing quality of capsules. We also determined the most favourable levels for the other seven parameters. The results allowed us to find optimal conditions in the experimental field. We obtained capsules of a satisfactory quality for this purpose, using only minimum experimentation.

Experimental study of self-leveling behavior in debris bed

International Nuclear Information System (INIS)

Zhang, Bin; Harada, Tetsushi; Hirahara, Daisuke; Matsumoto, Tatsuya; Morita, Koji; Fukuda, Kenji; Yamano, Hidemasa; Suzuki, Tohru; Tobita, Yoshiharu

2008-01-01

After a core disruptive accident in a sodium-cooled fast reactor, core debris may settle on locations such as within the core-support structure or in the lower inlet plenum of the reactor vessel as debris beds, as a consequence of rapid quenching and fragmentation of core materials in subcooled sodium. The particle beds that are initially of varying depth have been observed to undergo a process of self-leveling when sodium boiling occurs within the beds. The boiling is believed to provide the driven force with debris needed to overcome resisting forces. Self-leveling ability has much effect on heat-removal capability of debris beds. In the present study, characteristics of self-leveling behaviors were investigated experimentally with simulant materials. Although the decay heat from fuel debris drives the coolant boiling in reactor accident conditions, the present experiments employed depressurization boiling of water to simulate axially increasing void distribution in a debris bed, which consists of solid particles of alumina or lead with different density. The particle size (from 0.5 mm to 6 mm in diameter) and shape (spherical or non-spherical particles) were also taken as experimental parameters. A rough criteria for self-leveling occurrence is proposed and compared with the experimental results. Characteristics of the self-leveling behaviors observed are analyzed and extrapolate to reactor accident conditions. (author)

Estimation of time-varying pollutant emission rates in a ventilated enclosure: inversion of a reduced model obtained by experimental application of the modal identification method

International Nuclear Information System (INIS)

Girault, M; Maillet, D; Bonthoux, F; Galland, B; Martin, P; Braconnier, R; Fontaine, J R

2008-01-01

A method is proposed for the estimation of time-varying emission rates of pollutant sources in a ventilated enclosure, through the resolution of an inverse forced convection problem. Unsteady transport–diffusion of the pollutant is considered, with the assumption of a stationary velocity field remaining unchanged during emission (passive contaminant). The pollutant transport equation is therefore linear with respect to concentration. The source's location is also supposed to be known. As the first step, a reduced model (RM) linking concentrations at a set of control points to emission rates of sources is identified from experimental data by using the modal identification method (MIM). This parameter estimation problem uses transient contaminant concentration measurements made at control points inside the ventilated enclosure, corresponding to increasing and decreasing steps of emission rates. Such experimental modelling allows us to avoid dealing with a CFD code involving turbulence modelling and to get rid of uncertainties about sensors position. In a second step, the identified RM is used to solve an inverse forced convection problem: from contaminant concentration measured at the same control points, rates of sources emitting simultaneously are estimated with a sequential in time algorithm using future time steps

Effect of an experimental zirconia-silica coating technique on micro tensile bond strength of zirconia in different priming conditions

NARCIS (Netherlands)

Chen, C.; Kleverlaan, C.J.; Feilzer, A.J.

2012-01-01

Objectives This study aimed to evaluate the adhesive properties of a MDP-containing resin cement to a colored zirconia ceramic, using an experimental zirconia-silica coating technique with different priming conditions. Methods 18 zirconia ceramic discs (Cercon base colored) were divided into two

Preventative and Therapeutic Probiotic Use in Allergic Skin Conditions: Experimental and Clinical Findings

Science.gov (United States)

Özdemir, Öner; Göksu Erol, Azize Yasemin

2013-01-01

Probiotics are ingested live microbes that can modify intestinal microbial populations in a way that benefits the host. The interest in probiotic preventative/therapeutic potential in allergic diseases stemmed from the fact that probiotics have been shown to improve intestinal dysbiosis and permeability and to reduce inflammatory cytokines in human and murine experimental models. Enhanced presence of probiotic bacteria in the intestinal microbiota is found to correlate with protection against allergy. Therefore, many studies have been recently designed to examine the efficacy of probiotics, but the literature on the allergic skin disorders is still very scarce. Here, our objective is to summarize and evaluate the available knowledge from randomized or nonrandomized controlled trials of probiotic use in allergic skin conditions. Clinical improvement especially in IgE-sensitized eczema and experimental models such as atopic dermatitis-like lesions (trinitrochlorobenzene and picryl chloride sensitizations) and allergic contact dermatitis (dinitrofluorobenzene sensitization) has been reported. Although there is a very promising evidence to recommend the addition of probiotics into foods, probiotics do not have a proven role in the prevention or the therapy of allergic skin disorders. Thus, being aware of possible measures, such as probiotics use, to prevent/heal atopic diseases is essential for the practicing allergy specialist. PMID:24078929

Central recirculation zone analysis in an unconfined tangential swirl burner with varying degrees of premixing

Energy Technology Data Exchange (ETDEWEB)

Valera-Medina, A. [CIATEQ, Parque Industrial Bernardo Quintana, Turbomachinery Department, Queretaro (Mexico); Syred, N.; Kay, P.; Griffiths, A. [Cardiff University, School of Engineering, Cardiff, Wales (United Kingdom)

2011-06-15

Swirl-stabilised combustion is one of the most widely used techniques for flame stabilisation, uses ranging from gas turbine combustors to pulverised coal-fired power stations. In gas turbines, lean premixed systems are of especial importance, giving the ability to produce low NOx systems coupled with wide stability limits. The common element is the swirl burner, which depends on the generation of an aerodynamically formed central recirculation zone (CRZ) and which serves to recycle heat and active chemical species to the root of the flame as well as providing low-velocity regions where the flame speed can match the local flow velocity. Enhanced mixing in and around the CRZ is another beneficial feature. The structure of the CRZ and hence that of the associated flames, stabilisation and mixing processes have shown to be extremely complex, three-dimensional and time dependent. The characteristics of the CRZ depend very strongly on the level of swirl (swirl number), burner configuration, type of flow expansion, Reynolds number (i.e. flowrate) and equivalence ratio. Although numerical methods have had some success when compared to experimental results, the models still have difficulties at medium to high swirl levels, with complex geometries and varied equivalence ratios. This study thus focuses on experimental results obtained to characterise the CRZ formed under varied combustion conditions with different geometries and some variation of swirl number in a generic swirl burner. CRZ behaviour has similarities to the equivalent isothermal state, but is strongly dependent on equivalence ratio, with interesting effects occurring with a high-velocity fuel injector. Partial premixing and combustion cause more substantive changes to the CRZ than pure diffusive combustion. (orig.)

Effects of Ichthyophonus hoferi on condition indices and blood chemistry of experimentally infected rainbow trout (Oncorhynchus mykiss).

Science.gov (United States)

Rand, T G; Cone, D K

1990-07-01

Body condition, hepatosomatic index and blood chemistry of Oncorhynchus mykiss experimentally infected with a tissue dwelling fish pathogenic fungus, Ichthyophonus hoferi, were monitored over a 6 wk period. This was to determine whether the infection constituted a stress manifest by changes in the hypothalamic-pituitary interrenal axis, and especially plasma cortisol levels. Infection caused anaemia and leucopenia but did not change the condition, hepatosomatic indices, or plasma chloride, cholesterol, cortisol, creatinine, glucose, osmolarity, potassium, total protein, sodium and T4. It is suggested that increased cortisol levels may not be a normal component of the stress response of fish to disease caused by invasive infectious agents.

Robust stabilisation of time-varying delay systems with probabilistic uncertainties

Science.gov (United States)

Jiang, Ning; Xiong, Junlin; Lam, James

2016-09-01

For robust stabilisation of time-varying delay systems, only sufficient conditions are available to date. A natural question is as follows: if the existing sufficient conditions are not satisfied, and hence no controllers can be found, what can one do to improve the stability performance of time-varying delay systems? This question is addressed in this paper when there is a probabilistic structure on the parameter uncertainty set. A randomised algorithm is proposed to design a state-feedback controller, which stabilises the system over the uncertainty domain in a probabilistic sense. The capability of the designed controller is quantified by the probability of stability of the resulting closed-loop system. The accuracy of the solution obtained from the randomised algorithm is also analysed. Finally, numerical examples are used to illustrate the effectiveness and advantages of the developed controller design approach.

The Thermal Collector With Varied Glass Covers

International Nuclear Information System (INIS)

Luminosu, I.; Pop, N.

2010-01-01

The thermal collector with varied glass covers represents an innovation realized in order to build a collector able to reach the desired temperature by collecting the solar radiation from the smallest surface, with the highest efficiency. In the case of the thermal collector with variable cover glasses, the number of the glass plates covering the absorber increases together with the length of the circulation pipe for the working fluid. The thermal collector with varied glass covers compared to the conventional collector better meet user requirements because: for the same temperature increase, has the collecting area smaller; for the same collection area, realizes the highest temperature increase and has the highest efficiency. This works is addressed to researchers in the solar energy and to engineers responsible with air-conditioning systems design or industrial and agricultural products drying.

Experimental sintering of ash at conduit conditions and implications for the longevity of tuffisites

Science.gov (United States)

Gardner, James E.; Wadsworth, Fabian B.; Llewellin, Edward W.; Watkins, James M.; Coumans, Jason P.

2018-03-01

Escape of gas from magma in the conduit plays a crucial role in mitigating explosivity. Tuffisite veins—ash-filled cracks that form in and around volcanic conduits—represent important gas escape pathways. Sintering of the ash infill decreases its porosity, eventually forming dense glass that is impermeable to gas. We present an experimental investigation of surface tension-driven sintering and associated densification of rhyolitic ash under shallow conduit conditions. Suites of isothermal (700-800 °C) and isobaric H2O pressure (20 and 40 MPa) experiments were run for durations of 5-90 min. Obsidian powders with two different size distributions were used: 1-1600 μm (mean size = 89 μm), and 63-400 μm (mean size = 185 μm). All samples evolved similarly through four textural phases: phase 1—loose and cohesion-less particles; phase 2—particles sintered at contacts and surrounded by fully connected tortuous pore space of up to 40% porosity; phase 3—continuous matrix of partially coalesced particles that contain both isolated spherical vesicles and connected networks of larger, contorted vesicles; phase 4—dense glass with 2-5% fully isolated vesicles that are mainly spherical. Textures evolve faster at higher temperature and higher H2O pressure. Coarse samples sinter more slowly and contain fewer, larger vesicles when fully sintered. We quantify the sintering progress by measuring porosity as a function of experimental run-time, and find an excellent collapse of data when run-time is normalized by the sintering timescale {λ}_s=η \\overline{R}/σ , where η is melt viscosity, \\overline{R} is mean particle radius, and σ is melt-gas surface tension. Because timescales of diffusive H2O equilibration are generally fast compared to those of sintering, the relevant melt viscosity is calculated from the solubility H2O content at experimental temperature and pressure. We use our results to develop a framework for estimating ash sintering rates under shallow

Experimental and numerical study on frost heave of saturated rock under uniform freezing conditions

Science.gov (United States)

Lv, Zhitao; Xia, Caichu; Li, Qiang

2018-04-01

A series of freezing experiments are conducted on saturated sandstone and mortar specimens to investigate the frost heave of saturated rock under uniform freezing conditions. The experimental results show that the frost heave of saturated rock is isotropic under uniform freezing conditions. During the freezing process, three stages are observed in the curves of variation of total frost heaving strain versus time: the thermal contraction stage, the frost heaving stage and the steady stage. Moreover, the amount of final stable frost heave first increases and then decreases with decrease in freezing temperature, and the maximum final stable frost heave occurs at different freezing temperature in saturated sandstone and mortar. Furthermore, a coupled thermal-mechanical (TM) model of frost heave of saturated rock is proposed in which a constraint coefficient \\zeta is used to consider the susceptibility of the internal rock grain structure to the expansion of pore ice. Then, numerical simulations are implemented with COMSOL to solve the governing equations of the TM model. Comparisons of the numerical results with the experimental results are performed to demonstrate the reliability of the model. The influences of elastic modulus and porosity on frost heave are also investigated, and the results show that the total frost heaving strain decreases non-linearly with increasing elastic modulus, and the decrease is significant when the elastic modulus is less than 3000 MPa, or approximately five times the elastic modulus of ice. In addition, the total frost heaving strain increases linearly with increasing porosity. Finally, an empirical equation between total frost heaving strain and freezing temperature is proposed and the equation well describes the variation of total frost heaving strain with freezing temperature.

Experimental studies of microwave interaction with a plasma-covered planar conducting surface

International Nuclear Information System (INIS)

Destler, W.W.; Rodgers, J.; DeGrange, J.E.; Segalov, Z.

1990-01-01

The authors present experimental studies of the reflection and absorption of microwave radiation from a plasma-covered planar conducting surface. In the experiments, microwave radiation from both highpower, short pulse (10 GHz, 100 MW, 30 ns) and low power (10 GHz, 10 mW, CW) sources is radiated at a 30 cm diameter conducting plate. A time-varying plasma is created on the surface of the conductor by 19 coaxial plasma guns embedded in the surface of the plate and discharged using a fast-rise capacitor bank. The plasma density distribution on the conducting surface is a function of time and the charging voltage on the capacitor bank. Incident and reflected microwave radiation has been measured for a wide variety of experimental conditions

Vesicle biomechanics in a time-varying magnetic field.

Science.gov (United States)

Ye, Hui; Curcuru, Austen

2015-01-01

Cells exhibit distortion when exposed to a strong electric field, suggesting that the field imposes control over cellular biomechanics. Closed pure lipid bilayer membranes (vesicles) have been widely used for the experimental and theoretical studies of cellular biomechanics under this electrodeformation. An alternative method used to generate an electric field is by electromagnetic induction with a time-varying magnetic field. References reporting the magnetic control of cellular mechanics have recently emerged. However, theoretical analysis of the cellular mechanics under a time-varying magnetic field is inadequate. We developed an analytical theory to investigate the biomechanics of a modeled vesicle under a time-varying magnetic field. Following previous publications and to simplify the calculation, this model treated the inner and suspending media as lossy dielectrics, the membrane thickness set at zero, and the electric resistance of the membrane assumed to be negligible. This work provided the first analytical solutions for the surface charges, electric field, radial pressure, overall translational forces, and rotational torques introduced on a vesicle by the time-varying magnetic field. Frequency responses of these measures were analyzed, particularly the frequency used clinically by transcranial magnetic stimulation (TMS). The induced surface charges interacted with the electric field to produce a biomechanical impact upon the vesicle. The distribution of the induced surface charges depended on the orientation of the coil and field frequency. The densities of these charges were trivial at low frequency ranges, but significant at high frequency ranges. The direction of the radial force on the vesicle was dependent on the conductivity ratio between the vesicle and the medium. At relatively low frequencies (biomechanics under a time-varying magnetic field. Biological effects of clinical TMS are not likely to occur via alteration of the biomechanics of brain

Absorber and regenerator models for liquid desiccant air conditioning systems. Validation and comparison using experimental data

Energy Technology Data Exchange (ETDEWEB)

Krause, M.; Heinzen, R.; Jordan, U.; Vajen, K. [Kassel Univ., Inst. of Thermal Engineering, Kassel (Germany); Saman, W.; Halawa, E. [Sustainable Energy Centre, Univ. of South Australia, Mawson Lakes, Adelaide (Australia)

2008-07-01

Solar assisted air conditioning systems using liquid desiccants represent a promising option to decrease high summer energy demand caused by electrically driven vapor compression machines. The main components of liquid desiccant systems are absorbers for dehumidifying and cooling of supply air and regenerators for concentrating the desiccant. However, high efficient and validated reliable components are required and the design and operation have to be adjusted to each respective building design, location, and user demand. Simulation tools can help to optimize component and system design. The present paper presents new developed numerical models for absorbers and regenerators, as well as experimental data of a regenerator prototype. The models have been compared with a finite-difference method model as well as experimental data. The data are gained from the regenerator prototype presented and an absorber presented in the literature. (orig.)

You make me tired: An experimental test of the role of interpersonal operant conditioning in fatigue.

Science.gov (United States)

Lenaert, Bert; Jansen, Rebecca; van Heugten, Caroline M

2018-04-01

Chronic fatigue is highly prevalent in the general population as well as in multiple chronic diseases and psychiatric disorders. Its etiology however remains poorly understood and cannot be explained by biological factors alone. Occurring in a psychosocial context, the experience and communication of fatigue may be shaped by social interactions. In particular, interpersonal operant conditioning may strengthen and perpetuate fatigue complaints. In this experiment, individuals (N = 44) repeatedly rated their currently experienced fatigue while engaging in cognitive effort (working memory task). Subtle social reward was given when fatigue increased relative to the previous rating; or disapproval when fatigue decreased. In the control condition, only neutral feedback was given. Although all participants became more fatigued during cognitive effort, interpersonal operant conditioning led to increased fatigue reporting relative to neutral feedback. This effect occurred independently of conscious awareness. Interestingly, the experimental condition also performed worse on the working memory task. Results suggest that fatigue complaints (and cognitive performance) may become controlled by their consequences such as social reward, and not exclusively by their antecedents such as effort. Results have implications for treatment development and suggest that interpersonal operant conditioning may contribute to fatigue becoming a chronic symptom. Copyright © 2018 Elsevier Ltd. All rights reserved.

Clathrate hydrate dissociation conditions of refrigerants R404A, R406A, R408A and R427A: Experimental measurements and thermodynamic modeling

International Nuclear Information System (INIS)

Hashemi, Hamed; Babaee, Saeedeh; Mohammadi, Amir H.; Naidoo, Paramespri; Ramjugernath, Deresh

2015-01-01

Highlights: • The application of refrigerant hydrates in cold storage systems is investigated. • Hydrate dissociation conditions of various refrigerants have been measured. • A correlative thermodynamic model was applied to the data. • Enthalpy of dissociation for the refrigerants studied calculated. • Experimental measurements performed over a wide range of pressures. - Abstract: Clathrate hydrate dissociation conditions were measured for four “alternative” refrigerants, viz. R404A, R406A, R408A and R427A. The experimental measurements were performed within the pressure range of (0.079 to 9.995) MPa and temperatures ranging from (272.7 to 288.7) K. An isochoric pressure-search method was used to perform the measurements. A thermodynamic model based on the van der Waals–Platteeuw (vdW–P) model was applied for the prediction of the dissociation conditions which were compared to the experimental measurements. The fluid phase was modeled using the MHV2 G E -EoS mixing rule along with the UNIFAC (original) activity model. The van der Waals–Platteeuw (vdW–P) model was used for the modeling of the hydrate phase. There was reasonable agreement between the experimental and predicted values

Modeling and Analysis of a Piezoelectric Energy Harvester with Varying Cross-Sectional Area

Directory of Open Access Journals (Sweden)

Maiara Rosa

2014-01-01

Full Text Available This paper reports on the modeling and on the experimental verification of electromechanically coupled beams with varying cross-sectional area for piezoelectric energy harvesting. The governing equations are formulated using the Rayleigh-Ritz method and Euler-Bernoulli assumptions. A load resistance is considered in the electrical domain for the estimate of the electric power output of each geometric configuration. The model is first verified against the analytical results for a rectangular bimorph with tip mass reported in the literature. The experimental verification of the model is also reported for a tapered bimorph cantilever with tip mass. The effects of varying cross-sectional area and tip mass on the electromechanical behavior of piezoelectric energy harvesters are also discussed. An issue related to the estimation of the optimal load resistance (that gives the maximum power output on beam shape optimization problems is also discussed.

Experimental Investigation of Stiffness Characteristics and Damping Properties of a Metallic Rubber Material

Science.gov (United States)

Lu, Ch. Zh.; Li, Jingyuan; Zhou, Bangyang; Li, Shuang

2017-09-01

The static stiffness and dynamic damping properties of a metallic rubber material (MR) were investigated, which exhibited a nonlinear deformation behavior. Its static stiffness is analyzed and discussed. The effects of structural parameters of MR and experimental conditions on its shock absorption capacity were examined by dynamic tests. Results revealed excellent elastic and damping properties of the material. Its stiffness increased with density, but decreased with thickness. The damping property of MR varied with its density, thickness, loading frequency, and amplitude.

Plasma treatment of bulk niobium surface for superconducting rf cavities: Optimization of the experimental conditions on flat samples

Directory of Open Access Journals (Sweden)

M. Rašković

2010-11-01

Full Text Available Accelerator performance, in particular the average accelerating field and the cavity quality factor, depends on the physical and chemical characteristics of the superconducting radio-frequency (SRF cavity surface. Plasma based surface modification provides an excellent opportunity to eliminate nonsuperconductive pollutants in the penetration depth region and to remove the mechanically damaged surface layer, which improves the surface roughness. Here we show that the plasma treatment of bulk niobium (Nb presents an alternative surface preparation method to the commonly used buffered chemical polishing and electropolishing methods. We have optimized the experimental conditions in the microwave glow discharge system and their influence on the Nb removal rate on flat samples. We have achieved an etching rate of 1.7  μm/min⁡ using only 3% chlorine in the reactive mixture. Combining a fast etching step with a moderate one, we have improved the surface roughness without exposing the sample surface to the environment. We intend to apply the optimized experimental conditions to the preparation of single cell cavities, pursuing the improvement of their rf performance.

Heavy metals in precipitation waters under conditions of varied anthropopressure in typical of European low mountain regions

Directory of Open Access Journals (Sweden)

Rabajczyk A.

2013-04-01

Full Text Available The environment is a dynamic system, subject to change resulting from a variety of physicochemical factors, such as temperature, pressure, pH, redox potential and human activity. The quantity and variety of these determinants cause the inflow of substances into individual environmental elements to vary in both time and space, as well as in terms of substance types and quantities. The energy and matter flow in the environment determines its integrity, which means that the processes occurring in one element of the environment affect the others. A certain measure of the energy and matter flow is the migration of chemical substances in various forms from one place to another. In a particular geographical space, under natural conditions, a specific level of balance between individual processes appears; in areas subject to anthropopressure, the correlations are different. In small areas, varying deposition volumes and chemism of precipitation waters which reach the substratum directly can both be observed. The study area is similar in terms of geological origins as well as morphological, structural and physico-chemical properties, and is typical of European low mountain regions. A qualitative and quantitative study of wet atmospheric precipitation was conducted between February 2009 and May 2011 in the Bobrza river catchment in the Holy Cross (Świętokrzyskie Mountains (Poland, at three sampling sites of varying land development and distance from sources of various acidic-alkaline emissions. Field and laboratory work was conducted over 29 months, from February 2009 to May 2011. Atmospheric precipitation measurements were carried out in a continuous manner by means of a Hellman rain gauge (200cm2. The collecting surface was placed at ground level (0m AGL. The application of a collecting funnel and an adequately prepared polyethylene collecting can in the rain gauge enabled the measurement of precipitation volume and water sampling for chemical

Conditional Cooperation and the Marginal per Capita Return in Public Good Games

Directory of Open Access Journals (Sweden)

Edward J. Cartwright

2014-11-01

Full Text Available We investigate experimentally whether the extent of conditional cooperation in public good games depends on the marginal per capita return (MPCR to the public good and type of game. The MPCR is varied from 0.2 to 0.4 to 0.8. The ‘standard’ game, in which three players contribute before a follower, is compared with a leader-follower game, in which one player leads and three follow. Even though we observe less conditional cooperation for an MPCR of 0.2, the prevalence of conditional cooperation remains relatively stable to changes in the MPCR and game timing. In contrast, the level of MPCR has a strong effect on unconditional contributions. Our results highlight the critical role played by leaders in a public good game.

Evaluation of the Survivability of Microorganisms Deposited on Filtering Respiratory Protective Devices under Varying Conditions of Humidity

Directory of Open Access Journals (Sweden)

Katarzyna Majchrzycka

2016-01-01

Full Text Available Bioaerosols are common biological factors in work environments, which require routine use of filtering respiratory protective devices (FRPDs. Currently, no studies link humidity changes in the filter materials of such devices, during use, with microorganism survivability. Our aim was to determine the microclimate inside FRPDs, by simulating breathing, and to evaluate microorganism survivability under varying humidity conditions. Breathing was simulated using commercial filtering facepiece respirators in a model system. Polypropylene melt-blown nonwoven fabrics with moisture contents of 40%, 80%, and 200%, were used for assessment of microorganisms survivability. A modified AATCC 100-2004 method was used to measure the survivability of ATCC and NCAIM microorganisms: Escherichia coli, Staphylococcus aureus, Bacillus subtilis, Candida albicans and Aspergillus niger. During simulation relative humidity under the facepiece increased after 7 min of usage to 84%–92% and temperature increased to 29–30 °C. S. aureus survived the best on filter materials with 40%–200% moisture content. A decrease in survivability was observed for E. coli and C. albicans when mass humidity decreased. We found that B. subtilis and A. niger proliferated for 48–72 h of incubation and then died regardless of the moisture content. In conclusion, our tests showed that the survivability of microorganisms on filter materials depends on the amount of accumulated moisture and microorganism type.

Evaluation of the Survivability of Microorganisms Deposited on Filtering Respiratory Protective Devices under Varying Conditions of Humidity.

Science.gov (United States)

Majchrzycka, Katarzyna; Okrasa, Małgorzata; Skóra, Justyna; Gutarowska, Beata

2016-01-04

Bioaerosols are common biological factors in work environments, which require routine use of filtering respiratory protective devices (FRPDs). Currently, no studies link humidity changes in the filter materials of such devices, during use, with microorganism survivability. Our aim was to determine the microclimate inside FRPDs, by simulating breathing, and to evaluate microorganism survivability under varying humidity conditions. Breathing was simulated using commercial filtering facepiece respirators in a model system. Polypropylene melt-blown nonwoven fabrics with moisture contents of 40%, 80%, and 200%, were used for assessment of microorganisms survivability. A modified AATCC 100-2004 method was used to measure the survivability of ATCC and NCAIM microorganisms: Escherichia coli, Staphylococcus aureus, Bacillus subtilis, Candida albicans and Aspergillus niger. During simulation relative humidity under the facepiece increased after 7 min of usage to 84%-92% and temperature increased to 29-30 °C. S. aureus survived the best on filter materials with 40%-200% moisture content. A decrease in survivability was observed for E. coli and C. albicans when mass humidity decreased. We found that B. subtilis and A. niger proliferated for 48-72 h of incubation and then died regardless of the moisture content. In conclusion, our tests showed that the survivability of microorganisms on filter materials depends on the amount of accumulated moisture and microorganism type.

Perspectives of experimental and theoretical studies of self-organized dust structures in complex plasmas under microgravity conditions

International Nuclear Information System (INIS)

Tsytovich, V N

2015-01-01

We review research aimed at understanding the phenomena occurring in a complex plasma under microgravity conditions. Some aspects of the work already performed are considered that have not previously been given sufficient attention but which are potentially crucial for future work. These aspects, in particular, include the observation of compact dust structures that are estimated to be capable of confining all components of a dust plasma in a bounded spatial volume; experimental evidence of the nonlinear screening of dust particles; and experimental evidence of the excitation of collective electric fields. In theoretical terms, novel collective attraction processes between likely charged dust particles are discussed and all schemes of the shadowy attraction between dust particles used earlier, including in attempts to interpret observations, are reviewed and evaluated. Dust structures are considered from the standpoint of the current self-organization theory. It is emphasized that phase transitions between states of self-organized systems differ significantly from those in homogeneous states and that the phase diagrams should be constructed in terms of the parameters of a self-organized structure and cannot be constructed in terms of the temperature and density or similar parameters of homogeneous structures. Using the existing theoretical approaches to modeling self-organized structures in dust plasmas, the parameter distribution of a structure is recalculated for a simpler model that includes the quasineutrality condition and neglects diffusion. These calculations indicate that under microgravity conditions, any self-organized structure can contain a limited number of dust particles and is finite in size. The maximum possible number of particles in a structure determines the characteristic inter-grain distance in dust crystals that can be created under microgravity conditions. Crystallization criteria for the structures are examined and the quasispherical

Monitoring of 7Be in surface air of varying PM10 concentrations

International Nuclear Information System (INIS)

Chao, J.H.; Liu, C.C.; Cho, I.C.; Niu, H.

2014-01-01

In this study, beryllium-7 ( 7 Be) concentrations of surface air were monitored throughout a span of 23 years (1992–2012) in the Taiwanese cities Yilan, Taipei, Taichung, and Kaohsiung. During this period, particulate matter (PM) concentrations, in terms of PM 10 , were collected monthly from the nearest air-quality pollutant monitoring stations and compared against 7 Be concentrations. Seasonal monsoons influenced 7 Be concentrations in all cities, resulting in high winter and low summer concentrations. In addition, the meteorological conditions caused seasonal PM 10 variations, yielding distinct patterns among the cities. There was no correlation between 7 Be and PM 10 in the case cities. The average annual 7 Be concentrations varied little among the cities, ranging from 2.9 to 3.5 mBq/m 3 , while the PM 10 concentrations varied significantly from 38 μg/m 3 in Yilan to 92 μg/m 3 in Kaohsiung depending on the degree of air pollution and meteorological conditions. The correlation between the 7 Be concentration and gross-beta activities (A β ) in air implied that the 7 Be was mainly attached to crustal PM and its concentration varied little among the cities, regardless of the increase in anthropogenic PM in air-polluted areas. - Highlights: • Both 7 Be and PM 10 concentrations were monitored in four Taiwanese cities from 1992 to 2012. • Seasonal variations of 7 Be and PM 10 were explained based on on meteorological and pollution conditions. • The annual concentrations of 7 Be varied little among the four cities even in high PM environment. • 7 Be is believed to mainly attach to natural PM in the cities that exhibited varying PM 10 concentrations

Influence of different process settings conditions on the accuracy of micro injection molding simulations: an experimental validation

DEFF Research Database (Denmark)

Tosello, Guido; Gava, Alberto; Hansen, Hans Nørgaard

2009-01-01

Currently available software packages exhibit poor results accuracy when performing micro injection molding (µIM) simulations. However, with an appropriate set-up of the processing conditions, the quality of results can be improved. The effects on the simulation results of different and alternative...... process conditions are investigated, namely the nominal injection speed, as well as the cavity filling time and the evolution of the cavity injection pressure as experimental data. In addition, the sensitivity of the results to the quality of the rheological data is analyzed. Simulated results...... are compared with experiments in terms of flow front position at part and micro features levels, as well as cavity injection filling time measurements....

Effects of the imposed pressure differential conditions on duoplasmatron performance

International Nuclear Information System (INIS)

Oztarhan, A.

1988-01-01

The duoplasmatron plasma source (D.P.T.) was modified to allow access to the arc discharge (to measure the discharge properties) and to vary independently the pressures in different volumes of the arc with the aim of seeing if this freedom would help in optimising the output. The duoplasmatron plasma source was operated under normal running condition (N.R.C.), positive imposed pressure differential condition (P.I.P.D.C.) and negative imposed pressure differential condition (N.I.P.D.C.) and the corresponding properties of the plasma output were measured. Running the duoplasmatron under P.I.P.D. condition did not seem to improve the output as compared to that under N.R.C. However, running the duoplasmatron under N.I.P.D. condition seemed to be advantageous as the output increased by about 30%. It was observed that the back pressure was critical in maintaining the arc and the gap pressure could be lowered much below the normal minimum (while the arc was on) if back pressure was kept above a critical value. The results showed that the effects of varying the dimensions of the intermediate electrode nozzle on the output could be understood in terms of the effect of changes in these dimensions on the relative pressures. An empirical expression for the effect of the pressure ratio was developed from the observations and compared with the experimental results. The reasons for various results can be related to the plasma emission mechanism. (author). 8 refs, 6 figs, 1 tab

Identification of key factors in Accelerated Low Water Corrosion through experimental simulation of tidal conditions: influence of stimulated indigenous microbiota

NARCIS (Netherlands)

Marty, F.; Gueuné, H.; Malard, E.; Sánchez-Amaya, J.M.; Sjögren, L.; Abbas, B.; Quillet, L.; van Loosdrecht, M.C.M.; Muyzer, G.

2014-01-01

Biotic and abiotic factors favoring Accelerated Low Water Corrosion (ALWC) on harbor steel structures remain unclear warranting their study under controlled experimental tidal conditions. Initial stimulation of marine microbial consortia by a pulse of organic matter resulted in localized corrosion

Determinants for swine mycoplasmal pneumonia reproduction under experimental conditions: A systematic review and recursive partitioning analysis

Science.gov (United States)

Garcia-Morante, Beatriz; Segalés, Joaquim; Serrano, Emmanuel

2017-01-01

One of the main Mycoplasma hyopneumoniae (M. hyopneumoniae) swine experimental model objectives is to reproduce mycoplasmal pneumonia (MP). Unfortunately, experimental validated protocols to maximize the chance to successfully achieve lung lesions induced by M. hyopneumoniae are not available at the moment. Thus, the objective of this work was to identify those factors that might have a major influence on the effective development of MP, measured as macroscopic lung lesions, under experimental conditions. Data from 85 studies describing M. hyopneumoniae inoculation experiments were compiled by means of a systematic review and analyzed thereafter. Several variables were considered in the analyses such as the number of pigs in the experiment, serological status against M. hyopneumoniae, source of the animals, age at inoculation, type of inoculum, strain of M. hyopneumoniae, route, dose and times of inoculation, study duration and co-infection with other swine pathogens. Descriptive statistics were used to depict M. hyopneumoniae experimental model main characteristics whereas a recursive partitioning approach, using regression trees, assessed the importance of the abovementioned experimental variables as MP triggering factors. A strong link between the time period between challenge and necropsies and lung lesion severity was observed. Results indicated that the most important factors to explain the observed lung lesion score variability were: (1) study duration, (2) M. hyopneumoniae strain, (3) age at inoculation, (4) co-infection with other swine pathogens and (5) animal source. All other studied variables were not relevant to explain the variability on M. hyopneumoniae lung lesions. The results provided in the present work may serve as a basis for debate in the search for a universally accepted M. hyopneumoniae challenge model. PMID:28742802

Determinants for swine mycoplasmal pneumonia reproduction under experimental conditions: A systematic review and recursive partitioning analysis.

Directory of Open Access Journals (Sweden)

Beatriz Garcia-Morante

Full Text Available One of the main Mycoplasma hyopneumoniae (M. hyopneumoniae swine experimental model objectives is to reproduce mycoplasmal pneumonia (MP. Unfortunately, experimental validated protocols to maximize the chance to successfully achieve lung lesions induced by M. hyopneumoniae are not available at the moment. Thus, the objective of this work was to identify those factors that might have a major influence on the effective development of MP, measured as macroscopic lung lesions, under experimental conditions. Data from 85 studies describing M. hyopneumoniae inoculation experiments were compiled by means of a systematic review and analyzed thereafter. Several variables were considered in the analyses such as the number of pigs in the experiment, serological status against M. hyopneumoniae, source of the animals, age at inoculation, type of inoculum, strain of M. hyopneumoniae, route, dose and times of inoculation, study duration and co-infection with other swine pathogens. Descriptive statistics were used to depict M. hyopneumoniae experimental model main characteristics whereas a recursive partitioning approach, using regression trees, assessed the importance of the abovementioned experimental variables as MP triggering factors. A strong link between the time period between challenge and necropsies and lung lesion severity was observed. Results indicated that the most important factors to explain the observed lung lesion score variability were: (1 study duration, (2 M. hyopneumoniae strain, (3 age at inoculation, (4 co-infection with other swine pathogens and (5 animal source. All other studied variables were not relevant to explain the variability on M. hyopneumoniae lung lesions. The results provided in the present work may serve as a basis for debate in the search for a universally accepted M. hyopneumoniae challenge model.

Flow in curved ducts of varying cross-section

Science.gov (United States)

Sotiropoulos, F.; Patel, V. C.

1992-07-01

Two numerical methods for solving the incompressible Navier-Stokes equations are compared with each other by applying them to calculate laminar and turbulent flows through curved ducts of regular cross-section. Detailed comparisons, between the computed solutions and experimental data, are carried out in order to validate the two methods and to identify their relative merits and disadvantages. Based on the conclusions of this comparative study a numerical method is developed for simulating viscous flows through curved ducts of varying cross-sections. The proposed method is capable of simulating the near-wall turbulence using fine computational meshes across the sublayer in conjunction with a two-layer k-epsilon model. Numerical solutions are obtained for: (1) a straight transition duct geometry, and (2) a hydroturbine draft-tube configuration at model scale Reynolds number for various inlet swirl intensities. The report also provides a detailed literature survey that summarizes all the experimental and computational work in the area of duct flows.

Experimental Analysis of a Piezoelectric Energy Harvesting System for Harmonic, Random, and Sine on Random Vibration

Directory of Open Access Journals (Sweden)

Jackson W. Cryns

2013-01-01

Full Text Available Harvesting power with a piezoelectric vibration powered generator using a full-wave rectifier conditioning circuit is experimentally compared for varying sinusoidal, random, and sine on random (SOR input vibration scenarios; the implications of source vibration characteristics on harvester design are discussed. The rise in popularity of harvesting energy from ambient vibrations has made compact, energy dense piezoelectric generators commercially available. Much of the available literature focuses on maximizing harvested power through nonlinear processing circuits that require accurate knowledge of generator internal mechanical and electrical characteristics and idealization of the input vibration source, which cannot be assumed in general application. Variations in source vibration and load resistance are explored for a commercially available piezoelectric generator. The results agree with numerical and theoretical predictions in the previous literature for optimal power harvesting in sinusoidal and flat broadband vibration scenarios. Going beyond idealized steady-state sinusoidal and flat random vibration input, experimental SOR testing allows for more accurate representation of real world ambient vibration. It is shown that characteristic interactions from more complex vibration sources significantly alter power generation and processing requirements by varying harvested power, shifting optimal conditioning impedance, inducing voltage fluctuations, and ultimately rendering idealized sinusoidal and random analyses incorrect.

Weed spectrum and selectivity of tembotrione under varying environmental conditions

Directory of Open Access Journals (Sweden)

Gatzweiler, Elmar

2012-03-01

Full Text Available Tembotrione is a novel HPPD maize herbicide effective against a wide range of broadleaf and grass weeds. Some characteristics of this compound are described in this paper linking weed and crop responses following tembotrione applications to environmental parameters or use conditions. The activity of HPPD herbicides is very much dependant on the availability of light. Increasing illumination intensities following application augmented the activity levels of several comparable HPPD compounds in a growth chamber experiment. Tembotrione was shown to be more efficacious at low and high illumination intensities compared to standard herbicides applied at the same rate. At the high intensity, tembotrione retained its high efficacy from two up to four weeks after application showing a rapid and strong herbicidal activity. The activity following post-emergent treatments of tembotrione against broadleaf weeds was influenced by soil characteristics such as soil texture and organic matter content in a glasshouse test. The level of weed suppression clearly declined stronger on heavier soils than on lighter soils at a rather low application rate of 12.5 g a.i./ha and lower. This is a clear indication of residual efficacy of tembotrione. The selectivity of tembotrione was tested on numerous maize varieties following post-emergent treatment with tembotrione alone or in mixture with the safener isoxadifen-ethyl under field conditions in Germany in comparison to a standard herbicide. The level of crop phytotoxicity tended to increase in the following order: Tembotrione plus safener, standard herbicide to tembotrione alone. Only the mixture of tembotrione with safener did not cause significant adverse effects on maize. Another field experiment in the USA examined crop phytotoxicity using one maize variety in a situation of infurrow soil insecticide treatment followed by a post-emergent application of tembotrione (plus/minus isoxadifen-ethyl and standard herbicides

In-plane vibrations of inhomogeneous curved bars having varying cross-section

International Nuclear Information System (INIS)

Suzuki, Katsuyoshi; Kosawada, Tadashi; Takahashi, Shin

1986-01-01

An exact method using power series expansions is presented for solving in-plane free vibration problems of inhomogeneous curved bars having varying curvatures and cross-sections. Equations of motion and boundary conditions are derived from the stationary conditions of the Lagrangian of curved bars. Natural frequencies and mode shapes are presented for elliptical and circular arc bars having both ends clamped and calmped-free ends. (author)

Elements of a pragmatic approach for dealing with bias and uncertainty in experiments through predictions : experiment design and data conditioning; %22real space%22 model validation and conditioning; hierarchical modeling and extrapolative prediction.

Energy Technology Data Exchange (ETDEWEB)

Romero, Vicente Jose

2011-11-01

This report explores some important considerations in devising a practical and consistent framework and methodology for utilizing experiments and experimental data to support modeling and prediction. A pragmatic and versatile 'Real Space' approach is outlined for confronting experimental and modeling bias and uncertainty to mitigate risk in modeling and prediction. The elements of experiment design and data analysis, data conditioning, model conditioning, model validation, hierarchical modeling, and extrapolative prediction under uncertainty are examined. An appreciation can be gained for the constraints and difficulties at play in devising a viable end-to-end methodology. Rationale is given for the various choices underlying the Real Space end-to-end approach. The approach adopts and refines some elements and constructs from the literature and adds pivotal new elements and constructs. Crucially, the approach reflects a pragmatism and versatility derived from working many industrial-scale problems involving complex physics and constitutive models, steady-state and time-varying nonlinear behavior and boundary conditions, and various types of uncertainty in experiments and models. The framework benefits from a broad exposure to integrated experimental and modeling activities in the areas of heat transfer, solid and structural mechanics, irradiated electronics, and combustion in fluids and solids.

Benzodiazepines, opioids and driving: an overview of the experimental research.

Science.gov (United States)

Leung, Stefanie Y

2011-05-01

Road crashes contribute significantly to the total burden of injury in Australia, with the risk of injury being associated with the presence of drugs and/or alcohol in the driver's blood. Increasingly, some of the most commonly detected drugs include prescription medicines, the most notable of these being benzodiazepines and opioids. However, there is a paucity of experimental research into the effects of prescribed psychoactive drugs on driving behaviours. This paper provides an overview of experimental studies investigating the effects of prescribed doses of benzodiazepines and opioids on driving ability, and points to future directions for research. There is growing epidemiological evidence linking the therapeutic use of benzodiazepines and opioids to an increased crash risk. However, the current experimental literature remains unclear. Limitations to study methodologies have resulted in inconsistent findings. Limited experimental evidence exists to inform policy and guidelines regarding fitness-to-drive for patients taking prescribed benzodiazepines and opioids. Further experimental research is required to elucidate the effects of these medications on driving, under varying conditions and in different medical contexts. This will ensure that doctors prescribing benzodiazepines and opioids are well informed, and can appropriately advise patients of the risks associated with driving whilst taking these medications. © 2011 Australasian Professional Society on Alcohol and other Drugs.

Scalable Video Streaming Adaptive to Time-Varying IEEE 802.11 MAC Parameters

Science.gov (United States)

Lee, Kyung-Jun; Suh, Doug-Young; Park, Gwang-Hoon; Huh, Jae-Doo

This letter proposes a QoS control method for video streaming service over wireless networks. Based on statistical analysis, the time-varying MAC parameters highly related to channel condition are selected to predict available bitrate. Adaptive bitrate control of scalably-encoded video guarantees continuity in streaming service even if the channel condition changes abruptly.

Mate preference of female blue tits varies with experimental photoperiod.

Directory of Open Access Journals (Sweden)

Laura B Reparaz

Full Text Available Organisms use environmental cues to time their life-cycles and among these cues, photoperiod is the main trigger of reproductive behaviours such as territory defence or song activity. Whether photoperiod is also important for another behaviour closely associated with reproduction, mate choice, is unknown. In many bird species, mate choice occurs at two different times during the annual cycle that strongly differ in daylength: in late winter when photoperiod is short and social mates are chosen, and again around egg-laying when photoperiod is longer and extra-pair mates are chosen. This duality makes the role that photoperiod plays on mate choice behaviours intriguing. We investigated the effect of photoperiod on mate choice using three experimental photoperiodic treatments (9 L:15 D, 14 L:10 D, 18 L:6 D, using blue tits (Cyanistes caeruleus as a biological model. We show that female choice was stronger under long photoperiods. In addition, female blue tits spent significantly more time near males with long tarsi and long wings. This latter preference was only expressed under long photoperiods, suggesting that some indices of male quality only become significant to females when they are strongly photostimulated, and therefore that females could select their social and extra-pair mates based on different phenotypic traits. These results shed light on the roles that photoperiod may play in stimulating pair-bonding and in refining female selectivity for male traits.

Experimental impedance investigation of an ultracapacitor at different conditions for electric vehicle applications

Science.gov (United States)

Zhang, Lei; Hu, Xiaosong; Wang, Zhenpo; Sun, Fengchun; Dorrell, David G.

2015-08-01

Ultracapacitors (UCs) are being increasingly deployed as a short-term energy storage device in various energy systems including uninterruptable power supplies, electrified vehicles, renewable energy systems, and wireless communication. They exhibit excellent power density and energy efficiency. The dynamic behavior of a UC, however, strongly depends on its impedance characteristics. In this paper, the impedance characteristics of a commercial UC are experimentally investigated through the well-adopted Electrochemical Impedance Spectroscopy (EIS) technique. The implications of the UC operating conditions (i.e., temperature and state of charge (SOC)) to the impedance are systematically examined. The results show that the impedance is highly sensitive to the temperature and SOC; and the temperature effect is more significant. In particular, the coupling effect between the temperature and SOC is illustrated, as well as the high-efficiency SOC window, which is highlighted. To further verify the reliability of the EIS-based investigation and to probe the sensitivity of UC parameters to the operating conditions, a dynamic model is characterized by fitting the collected impedance data. The interdependence of UC parameters (i.e., capacitance and resistance elements) on the temperature and SOC is quantitatively revealed. The impedance-based model is demonstrated to be accurate in two driving-cycle tests.

Experimental quantum verification in the presence of temporally correlated noise

Science.gov (United States)

Mavadia, S.; Edmunds, C. L.; Hempel, C.; Ball, H.; Roy, F.; Stace, T. M.; Biercuk, M. J.

2018-02-01

Growth in the capabilities of quantum information hardware mandates access to techniques for performance verification that function under realistic laboratory conditions. Here we experimentally characterise the impact of common temporally correlated noise processes on both randomised benchmarking (RB) and gate-set tomography (GST). Our analysis highlights the role of sequence structure in enhancing or suppressing the sensitivity of quantum verification protocols to either slowly or rapidly varying noise, which we treat in the limiting cases of quasi-DC miscalibration and white noise power spectra. We perform experiments with a single trapped 171Yb+ ion-qubit and inject engineered noise (" separators="∝σ^ z ) to probe protocol performance. Experiments on RB validate predictions that measured fidelities over sequences are described by a gamma distribution varying between approximately Gaussian, and a broad, highly skewed distribution for rapidly and slowly varying noise, respectively. Similarly we find a strong gate set dependence of default experimental GST procedures in the presence of correlated errors, leading to significant deviations between estimated and calculated diamond distances in the presence of correlated σ^ z errors. Numerical simulations demonstrate that expansion of the gate set to include negative rotations can suppress these discrepancies and increase reported diamond distances by orders of magnitude for the same error processes. Similar effects do not occur for correlated σ^ x or σ^ y errors or depolarising noise processes, highlighting the impact of the critical interplay of selected gate set and the gauge optimisation process on the meaning of the reported diamond norm in correlated noise environments.

Remobilization of americium in soil columns under experimental rhizo-spheric conditions

Energy Technology Data Exchange (ETDEWEB)

Perrier, T.; Martin-Garin, A.; Morello, M. [CEA Cadarache (DEI/SECRE/LRE), Laboratory of Radioecology and Ecotoxicology, Institute for Radioprotection and Nuclear Safety, 13 - Saint-Paul-lez-Durance (France)

2004-07-01

The biogeochemical behaviour of americium in subsurface soils plays a dominant role on the potential migration of this actinide, but is currently poorly known. The identification and understanding of these processes is of major concern for this highly (radio)toxic element and can allow the determination of its impact on the natural media. This research investigates the relevant processes controlling americium biogeochemical speciation in the rhizosphere of an agricultural soil. Lixiviation tests were performed on columns packed with a 2 mm-sieved calcareous soil contaminated with {sup 241}Am (500 Bq.g{sup -1}), under steady-state unsaturated or saturated hydric flow conditions. The columns were percolated with soil solution of varied compositions, containing citrate and/or glucose simulating root exudates in non-sterile conditions. The physico-chemical parameters of the outlet solution (pH, conductivity, major ions, organic acids) were monitored, as well as the microbial activity. Inorganic and organic speciation of {sup 241}Am is supported by geochemical modeling with JChess, using a thermodynamic database based on NEA database and the latest PSI recommendations. The percolation of a solution in equilibrium with the soil released small amount of americium (<5 mBq/cm{sup 3}), as predicted by the high {sup 241}Am K{sub d} values. 10{sup -4} M concentrations of citrate, glucose or both combined did not enhance remobilization either. Poor remobilization was also observed at high glucose concentrations (10{sup -2} M), despite an effective glucose microbial degradation, the production of ligands such as acetate, and important changes in the chemistry of the solution. On the contrary, high concentrations of citrate (10{sup -2} M) released 1000 times more americium, which is in accordance with previous studies. Even greater releases (10000 times) were observed when 10{sup -2} M glucose was added to 10{sup -2} M citrate. The remobilization of americium resulting from the

Experimental Investigation of Separated and Transitional Boundary Layers Under Low-Pressure Turbine Airfoil Conditions

Science.gov (United States)

Hultgren, Lennart S.; Volino, Ralph J.

2002-01-01

Modern low-pressure turbine airfoils are subject to increasingly stronger pressure gradients as designers impose higher loading in an effort to improve efficiency and to reduce part count. The adverse pressure gradients on the suction side of these airfoils can lead to boundary-layer separation, particularly under cruise conditions. Separation bubbles, notably those which fail to reattach, can result in a significant degradation of engine efficiency. Accurate prediction of separation and reattachment is hence crucial to improved turbine design. This requires an improved understanding of the transition flow physics. Transition may begin before or after separation, depending on the Reynolds number and other flow conditions, has a strong influence on subsequent reattachment, and may even eliminate separation. Further complicating the problem are the high free-stream turbulence levels in a real engine environment, the strong pressure gradients along the airfoils, the curvature of the airfoils, and the unsteadiness associated with wake passing from upstream stages. Because of the complicated flow situation, transition in these devices can take many paths that can coexist, vary in importance, and possibly also interact, at different locations and instances in time. The present work was carried out in an attempt to systematically sort out some of these issues. Detailed velocity measurements were made along a flat plate subject to the same nominal dimensionless pressure gradient as the suction side of a modern low-pressure turbine airfoil ('Pak-B'). The Reynolds number based on wetted plate length and nominal exit velocity, Re, was varied from 50;000 to 300; 000, covering cruise to takeoff conditions. Low, 0.2%, and high, 7%, inlet free-stream turbulence intensities were set using passive grids. These turbulence levels correspond to about 0.2% and 2.5% turbulence intensity in the test section when normalized with the exit velocity. The Reynolds number and free

Performance of asphaltic concrete incorporating styrene butadiene rubber subjected to varying aging condition

Science.gov (United States)

Salah, Faisal Mohammed; Jaya, Ramadhansyah Putra; Mohamed, Azman; Hassan, Norhidayah Abdul; Rosni, Nurul Najihah Mad; Mohamed, Abdullahi Ali; Agussabti

2017-12-01

The influence of styrene butadiene rubber (SBR) on asphaltic concrete properties at different aging conditions was presented in this study. These aging conditions were named as un-aged, short-term, and long-term aging. The conventional asphalt binder of penetration grade 60/70 was used in this work. Four different levels of SBR addition were employed (i.e., 0 %, 1 %, 3 %, and 5 % by binder weight). Asphalt concrete mixes were prepared at selected optimum asphalt content (5 %). The performance was evaluated based on Marshall Stability, resilient modulus, and dynamic creep tests. Results indicated the improving stability and permanent deformation characteristics that the mixes modified with SBR polymer have under aging conditions. The result also showed that the stability, resilient modulus, and dynamic creep tests have the highest rates compared to the short-term aging and un-aged samples. Thus, the use of 5 % SBR can produce more durable asphalt concrete mixtures with better serviceability.

Experimental validation of a theoretical model for a direct-expansion solar-assisted heat pump applied to heating

International Nuclear Information System (INIS)

Moreno-Rodriguez, A.; Garcia-Hernando, N.; González-Gil, A.; Izquierdo, M.

2013-01-01

This paper discusses the experimental validation of a theoretical model that determines the operating parameters of a DXSAHP (direct-expansion solar-assisted heat pump) applied to heating. For this application, the model took into account the variable condensing temperature, and it was developed from the following environmental variables: outdoor temperature, solar radiation and wind. The experimental data were obtained from a prototype installed at the University Carlos III, which is located south of Madrid. The prototype uses a solar collector with a total area of 5.6 m 2 , a compressor with a rated capacity of 1100 W, a thermostatic expansion valve and fan-coil units as indoor terminals. The monitoring results were analyzed for several typical days in the climatic zone where the machine was located to understand the equipment's seasonal behavior. The experimental coefficient of the performance varies between 1.9 and 2.7, and the equipment behavior in extreme outdoor conditions has also been known to determine the thermal demand that can be compensated for. - Highlights: • The study aims to present an experimental validation of a theoretical model. • The experimental COP can vary between 1.9 and 2.7 (max. condensation temperature 59 °C). • A “dragging term” relates condensation and evaporation temperature. • The operating parameters respond to the solar radiation. The COP may increase up to 25%

Nitrous Oxide Production and Fluxes from Coastal Sediments under Varying Environmental Conditions

Science.gov (United States)

Ziebis, W.; Wankel, S. D.; de Beer, D.; Dentinger, J.; Buchwald, C.; Charoenpong, C.

2014-12-01

Although coastal zones represent important contributors to the increasing levels of atmospheric nitrous oxide (N2O), it is still unclear which role benthic processes play and whether marine sediments represent sinks or sources for N2O, since interactions among closely associated microbial groups lead to a high degree of variability. In addition, coastal areas are extremely dynamic regions, often exposed to increased nutrient loading and conditions of depleted oxygen. We investigated benthic N2O fluxes and how environmental conditions affect N2O production in different sediments at 2 different geographical locations (German Wadden Sea, a California coastal lagoon). At each location, a total of 32 sediment cores were taken in areas that differed in sediment type, organic content and pore-water nutrient concentrations, as well as in bioturbation activity. Parallel cores were incubated under in-situ conditions, low oxygen and increased nitrate levels for 10 days. Zones of N2O production and consumption were identified in intact cores by N2O microprofiles at the beginning and end of the experiments. In a collaborative effort to determine the dominant sources of N2O, samples were taken throughout the course of the experiments for the determination of the isotopic composition of N2O (as well as nitrate, nitrite and ammonium). Our results indicate that both, nitrate addition and low oxygen conditions in the overlying water, caused an increase of subsurface N2O production in most sediments, with a high variability between different sediment types. N2O production in the sediments was accompanied by N2O consumption, reducing the fluxes to the water column. In general, organic rich sediments showed the strongest response to environmental changes with increased production and efflux of N2O into the overlying water. Bioturbation activity added to the complexity of N2O dynamics by an increase in nitrification-denitrification processes, as well as enhanced pore-water transport

Delay-dependent exponential stability of cellular neural networks with time-varying delays

International Nuclear Information System (INIS)

Zhang Qiang; Wei Xiaopeng; Xu Jin

2005-01-01

The global exponential stability of cellular neural networks (CNNs) with time-varying delays is analyzed. Two new sufficient conditions ensuring global exponential stability for delayed CNNs are obtained. The conditions presented here are related to the size of delay. The stability results improve the earlier publications. Two examples are given to demonstrate the effectiveness of the obtained results

Does the Effect of Micro-Environmental Factors on a Street's Appeal for Adults' Bicycle Transport Vary across Different Macro-Environments? An Experimental Study.

Science.gov (United States)

Mertens, Lieze; Van Cauwenberg, Jelle; Ghekiere, Ariane; Van Holle, Veerle; De Bourdeaudhuij, Ilse; Deforche, Benedicte; Nasar, Jack; Van de Weghe, Nico; Van Dyck, Delfien

2015-01-01

Characteristics of the physical environment can be classified into two broad categories: macro- ("raw" urban planning features influenced on a regional level) and micro- (features specifically within a streetscape influenced on a neighborhood level) environmental factors. In urban planning applications, it is more feasible to modify conditions at the neighborhood level than at the regional level. Yet for the promotion of bicycle transport we need to know whether relationships between micro-environmental factors and bicycle transport depend on different types of macro-environments. This study aimed to identify whether the effect of three micro-environmental factors (i.e., evenness of the cycle path surface, speed limits and type of separation between cycle path and motorized traffic) on the street's appeal for adults' bicycle transport varied across three different macro-environments (i.e., low, medium and high residential density street). In total, 389 middle-aged adults completed a web-based questionnaire consisting of socio-demographic characteristics and a series of choice tasks with manipulated photographs, depicting two possible routes to cycle along. Conjoint analysis was used to analyze the data. Although the magnitude of the overall effects differed, in each macro-environment (i.e., low, medium and high residential density), middle-aged adults preferred a speed limit of 30 km/h, an even cycle path surface and a hedge as separation between motorized traffic and the cycle path compared to a speed limit of 50 or 70 km/h, a slightly uneven or uneven cycle path surface and a curb as separation or no separation between motorized traffic and the cycle path. Our results suggest that irrespective of the macro-environment, the same micro-environmental factors are preferred in middle-aged adults concerning the street's appeal for bicycle transport. The controlled environment simulations in the experimental choice task have the potential to inform real life

Does the Effect of Micro-Environmental Factors on a Street's Appeal for Adults' Bicycle Transport Vary across Different Macro-Environments? An Experimental Study.

Directory of Open Access Journals (Sweden)

Lieze Mertens

Full Text Available Characteristics of the physical environment can be classified into two broad categories: macro- ("raw" urban planning features influenced on a regional level and micro- (features specifically within a streetscape influenced on a neighborhood level environmental factors. In urban planning applications, it is more feasible to modify conditions at the neighborhood level than at the regional level. Yet for the promotion of bicycle transport we need to know whether relationships between micro-environmental factors and bicycle transport depend on different types of macro-environments. This study aimed to identify whether the effect of three micro-environmental factors (i.e., evenness of the cycle path surface, speed limits and type of separation between cycle path and motorized traffic on the street's appeal for adults' bicycle transport varied across three different macro-environments (i.e., low, medium and high residential density street.In total, 389 middle-aged adults completed a web-based questionnaire consisting of socio-demographic characteristics and a series of choice tasks with manipulated photographs, depicting two possible routes to cycle along. Conjoint analysis was used to analyze the data.Although the magnitude of the overall effects differed, in each macro-environment (i.e., low, medium and high residential density, middle-aged adults preferred a speed limit of 30 km/h, an even cycle path surface and a hedge as separation between motorized traffic and the cycle path compared to a speed limit of 50 or 70 km/h, a slightly uneven or uneven cycle path surface and a curb as separation or no separation between motorized traffic and the cycle path.Our results suggest that irrespective of the macro-environment, the same micro-environmental factors are preferred in middle-aged adults concerning the street's appeal for bicycle transport. The controlled environment simulations in the experimental choice task have the potential to inform real life

Time-Varying Value of Energy Efficiency in Michigan

Energy Technology Data Exchange (ETDEWEB)

Mims, Natalie; Eckman, Tom; Schwartz, Lisa C.

2018-04-02

Quantifying the time-varying value of energy efficiency is necessary to properly account for all of its benefits and costs and to identify and implement efficiency resources that contribute to a low-cost, reliable electric system. Historically, most quantification of the benefits of efficiency has focused largely on the economic value of annual energy reduction. Due to the lack of statistically representative metered end-use load shape data in Michigan (i.e., the hourly or seasonal timing of electricity savings), the ability to confidently characterize the time-varying value of energy efficiency savings in the state, especially for weather-sensitive measures such as central air conditioning, is limited. Still, electric utilities in Michigan can take advantage of opportunities to incorporate the time-varying value of efficiency into their planning. For example, end-use load research and hourly valuation of efficiency savings can be used for a variety of electricity planning functions, including load forecasting, demand-side management and evaluation, capacity planning, long-term resource planning, renewable energy integration, assessing potential grid modernization investments, establishing rates and pricing, and customer service (KEMA 2012). In addition, accurately calculating the time-varying value of efficiency may help energy efficiency program administrators prioritize existing offerings, set incentive or rebate levels that reflect the full value of efficiency, and design new programs.

Theoretical analysis and experimental research on dispersed-flow boiling heat transfer

International Nuclear Information System (INIS)

Yu Zhenwan; Jia Dounan; Li Linjiao; Mu Quanhou

1989-01-01

Experiment on dispersed-flow boiling heat transfer at low pressure has been done. The hot patch technique has been used to establish post-dryout conditions. The position of the hot patch can be varied along the test section. The superheated vapor temperatures at different elevations after dryout point are obtained. The experimental data are generally in agreement with the models of predictions of existing nonequilibrium film boiling. A heat transfer model for dispersed-flow boiling heat transfer has been developed. And the model can explain the phenomena of heat transfer near the dryout point. (orig./DG)

Discrete-Time Sliding-Mode Control of Uncertain Systems with Time-Varying Delays via Descriptor Approach

Directory of Open Access Journals (Sweden)

Maode Yan

2008-01-01

Full Text Available This paper considers the problem of robust discrete-time sliding-mode control (DT-SMC design for a class of uncertain linear systems with time-varying delays. By applying a descriptor model transformation and Moon's inequality for bounding cross terms, a delay-dependent sufficient condition for the existence of stable sliding surface is given in terms of linear matrix inequalities (LMIs. Based on this existence condition, the synthesized sliding mode controller can guarantee the sliding-mode reaching condition of the specified discrete-time sliding surface for all admissible uncertainties and time-varying delays. An illustrative example verifies the effectiveness of the proposed method.

Adult Tea Green Leafhoppers, Empoasca onukii (Matsuda), Change Behaviors under Varying Light Conditions.

Science.gov (United States)

Shi, Longqing; Vasseur, Liette; Huang, Huoshui; Zeng, Zhaohua; Hu, Guiping; Liu, Xin; You, Minsheng

2017-01-01

Insect behaviors are often influenced by light conditions including photoperiod, light intensity, and wavelength. Understanding pest insect responses to changing light conditions may help with developing alternative strategies for pest control. Little is known about the behavioral responses of leafhoppers (Hemiptera: Cicadellidae) to light conditions. The behavior of the tea green leafhopper, Empoasca onukii Matsuda, was examined when exposed to different light photoperiods or wavelengths. Observations included the frequency of locomotion and cleaning activities, and the duration of time spent searching. The results suggested that under normal photoperiod both female and male adults were generally more active in darkness (i.e., at night) than in light. In continuous darkness (DD), the locomotion and cleaning events in Period 1 (7:00-19:00) were significantly increased, when compared to the leafhoppers under normal photoperiod (LD). Leafhoppers, especially females, changed their behavioral patterns to a two day cycle under DD. Under continuous illumination (continuous quartz lamp light, yellow light at night, and green light at night), the activities of locomotion, cleaning, and searching were significantly suppressed during the night (19:00-7:00) and locomotion activities of both females and males were significantly increased during the day (7:00-19:00), suggesting a shift in circadian rhythm. Our work suggests that changes in light conditions, including photoperiod and wavelength, can influence behavioral activities of leafhoppers, potentially affecting other life history traits such as reproduction and development, and may serve as a method for leafhopper behavioral control.

Experimental evidence for the cardioprotective effects of red wine.

Science.gov (United States)

Das, Samarjit; Santani, Dev D; Dhalla, Naranjan S

2007-01-01

Both epidemiological and experimental studies have revealed that intake of wine, particularly red wine, in moderation protects cardiovascular health; however, the experimental basis for such an action is not fully understood. Because all types of red wine contain varying amounts of alcohol and antioxidants, it is likely that the cardioprotective effect of red wine is due to both these constituents. In view of its direct action on the vascular smooth muscle cells, alcohol may produce coronary vasodilation in addition to attenuating oxidative stress by its action on the central nervous system. The antioxidant components of red wine may provide cardioprotection by their ability to reduce oxidative stress in the heart under different pathological conditions. Mild-to-moderate red wine consumption improves cardiac function in the ischemic myocardium through the protection of endothelial function, the expression of several cardioprotective oxidative stress-inducible proteins, as well as the activation of adenosine receptors and nitrous oxide synthase mechanisms.

Experimental evidence for the cardioprotective effects of red wine

Science.gov (United States)

Das, Samarjit; Santani, Dev D; Dhalla, Naranjan S

2007-01-01

Both epidemiological and experimental studies have revealed that intake of wine, particularly red wine, in moderation protects cardiovascular health; however, the experimental basis for such an action is not fully understood. Because all types of red wine contain varying amounts of alcohol and antioxidants, it is likely that the cardioprotective effect of red wine is due to both these constituents. In view of its direct action on the vascular smooth muscle cells, alcohol may produce coronary vasodilation in addition to attenuating oxidative stress by its action on the central nervous system. The antioxidant components of red wine may provide cardioprotection by their ability to reduce oxidative stress in the heart under different pathological conditions. Mild-to-moderate red wine consumption improves cardiac function in the ischemic myocardium through the protection of endothelial function, the expression of several cardioprotective oxidative stress-inducible proteins, as well as the activation of adenosine receptors and nitrous oxide synthase mechanisms. PMID:18650973

Useful model organisms, indicators, or both? Ground beetles (Coleoptera, Carabidae) reflecting environmental conditions.

Science.gov (United States)

Koivula, Matti J

2011-01-01

Classic studies have successfully linked single-species abundances, life-history traits, assemblage structures and biomass of carabid beetles to past and present, human-caused environmental impacts and variation in 'natural' conditions. This evidence has led many to suggest carabids to function as 'indicators' - a term that bears multiple meanings. Here, a conservation-oriented definition for an indicator is used, carabid indicator potential from seven views is evaluated, and ways to proceed in indicator research are discussed. (1) Carabid species richness poorly indicates the richness and abundance of other taxa, which underlines the importance of using multiple taxa in environmental assessments. The ability of assemblage indices and specialist or functional-group abundances to reflect rare species and habitats should be examined in detail. (2) Experimental evidence suggests that carabids may potentially serve as keystone indicators. (3) Carabids are sensitive to human-altered abiotic conditions, such as pesticide use in agro-ecosystems and heavy metal contamination of soils. Carabids might thus reflect ecological sustainability and 'ecosystem health'. (4) Carabid assemblages host abundant species characteristic of particular habitat types or successional stages, which makes them promising dominance indicators. (5) Carabids reflect variation in 'natural' conditions, but vegetation and structural features are more commonly adopted as condition indicators. Carabids nevertheless provide yet another, equally accurate, view on the structure of the environment. (6) Carabids may function as early-warning signalers, as suggested by recent studies linking climate and carabid distributions. (7) Carabids reflect natural and human-caused disturbances and management, but the usefulness of these responses for conservation purposes requires further research. In summary, European carabids appear useful model organisms and possibly indicators because they are diverse

Useful model organisms, indicators, or both? Ground beetles (Coleoptera, Carabidae reflecting environmental conditions

Directory of Open Access Journals (Sweden)

Matti Koivula

2011-05-01

Full Text Available Classic studies have successfully linked single-species abundances, life-history traits, assemblage structures and biomass of carabid beetles to past and present, human-caused environmental impacts and variation in ‘natural’ conditions. This evidence has led many to suggest carabids to function as ‘indicators’ − a term that bears multiple meanings. Here, a conservation-oriented definition for an indicator is used, carabid indicator potential from seven views is evaluated, and ways to proceed in indicator research are discussed. (1 Carabid species richness poorly indicates the richness and abundance of other taxa, which underlines the importance of using multiple taxa in environmental assessments. The ability of assemblage indices and specialist or functional-group abundances to reflect rare species and habitats should be examined in detail. (2 Experimental evidence suggests that carabids may potentially serve as keystone indicators. (3 Carabids are sensitive to human-altered abiotic conditions, such as pesticide use in agro-ecosystems and heavy metal contamination of soils. Carabids might thus reflect ecological sustainability and ‘ecosystem health’. (4 Carabid assemblages host abundant species characteristic of particular habitat types or successional stages, which makes them promising dominance indicators. (5 Carabids reflect variation in ‘natural’ conditions, but vegetation and structural features are more commonly adopted as condition indicators. Carabids nevertheless provide yet another, equally accurate, view on the structure of the environment. (6 Carabids may function as early-warning signalers, as suggested by recent studies linking climate and carabid distributions. (7 Carabids reflect natural and human-caused disturbances and management, but the usefulness of these responses for conservation purposes requires further research. In summary, European carabids appear useful model organisms and possibly indicators because

Optimal conditions for particle-bubble attachment in flotation: an experimental study

Science.gov (United States)

Sanchez Yanez, Aaron; Hernandez Sanchez, Jose Federico; Thoroddsen, Sigurdur T.

2017-11-01

Mineral flotation is a process used in the mining industry for separating solid particles of different sizes and densities. The separation is done by injecting bubbles into a slurry where the particles attach to them, forming floating aggregates. The attachment depends mainly on the bubbles and particles sizes as well as the hydrophobicity and roughness of the particles. We simplified the collective behavior in the industrial process to a single free particle-bubble collision, in contrast with previous studies where one of the two was kept fixed. We experimentally investigated the collision of spherical solid particles of a fixed diameter with bubbles of different sizes. By controlling the initial relative offset of the bubble and the particle, we conducted experiments observing their interaction. Recording with two synchronized high-speed cameras, perpendicular to each other, we can reconstruct the tridimensional trajectories of the bubble, the solid particle, and the aggregate. We describe the conditions for which the attachment happens in terms of dimensionless parameters such as the Ohnesorge number, the relative particle-bubble offset and the hydrophobicity of the particle surface. We furthermore investigate the role of the surface roughness in the attachment.

Experimental investigation of mixing of non-isothermal water streams at BWR operating conditions

Energy Technology Data Exchange (ETDEWEB)

Bergagio, Mattia, E-mail: bergagio@kth.se [AlbaNova University Center, Nuclear Reactor Technology Division, Department of Physics, Royal Institute of Technology, 106 91 Stockholm (Sweden); Anglart, Henryk, E-mail: henryk@kth.se [AlbaNova University Center, Nuclear Reactor Technology Division, Department of Physics, Royal Institute of Technology, 106 91 Stockholm (Sweden); Institute of Heat Engineering, Warsaw University of Technology, 21/25 Nowowiejska Street, 00-665 Warsaw (Poland)

2017-06-15

Highlights: • Temperatures are measured in the presence of mixing at BWR operating conditions. • The thermocouple support is moved along a pattern to extend the measurement region. • Uncertainty of 1.58 K for temperatures acquired at 1000 Hz. • Momenta of the hot streams and thermal stratification affect the data examined. • Unconventional spectral analysis is required to further study the data collected. - Abstract: In this experimental investigation, wall surface temperatures have been measured during mixing of three water streams in the annular gap between two coaxial stainless-steel tubes. The inner tube, with an outer diameter of 35 mm and a thickness of 5 mm, holds six K-type, ungrounded thermocouples with a diameter of 0.5 mm, which measured surface temperatures with a sampling rate of either 100 Hz or 1000 Hz. The tube was rotated from 0 to 360° and moved in a range of 387 mm in the axial direction to allow measurements of surface temperatures in the whole mixing region. The outer tube has an inner diameter of 80 mm and a thickness of 10 mm to withstand a water pressure of 9 MPa. A water stream at a temperature of either 333 K or 423 K and a Reynolds number between 1657 and 8410 rose vertically in the annular gap and mixed with two water streams at a temperature of 549 K and a Reynolds number between 3.56 × 10{sup 5} and 7.11 × 10{sup 5}. These two water streams entered the annulus radially on the same axial level, 180° apart. Water pressure was kept at 7.2 MPa. Temperature recordings were performed at five axial and eight azimuthal locations, for each set of boundary conditions. Each recording lasted 120 s to provide reliable data on the variance, intermittency and frequency of the surface temperature time series at hand. Thorough calculations indicate that the uncertainty in the measured temperature is of 1.58 K. The mixing region extends up to 0.2 m downward of the hot inlets. In most cases, measurements indicate non-uniform mixing in the

Experimental conditions and monitoring items of the prototype repository project (PRP). Research document

International Nuclear Information System (INIS)

Sugita, Yutaka; Ito, Akira; Kawakami, Susumu

2003-03-01

Various experiments are ongoing in the underground research facility 'the Hard Rock Laboratory (HRL)' of SKB in Sweden for the geological disposal of the high-level radioactive waste. International joint project Prototype Repository Project (PRP) is one of the experiments in the HRL which has some engineered barrier systems and to study the coupled behavior happening in and around the engineered barrier system. JNC has joined this international joint project PRP to obtain the information of the coupled behavior on such systematic engineered barrier system and to apply the JNC's coupled THMC analytical code to the prediction and back analysis of the PRP. The analytical code will be verified through these analyses in this project. JNC can apply the verified analytical code to assess the coupled behavior in Japan. This report summarizes the experimental conditions and monitoring items of the PRP. (author)

Exergo-Economic Analysis of an Experimental Aircraft Turboprop Engine Under Low Torque Condition

Science.gov (United States)

Atilgan, Ramazan; Turan, Onder; Aydin, Hakan

Exergo-economic analysis is an unique combination of exergy analysis and cost analysis conducted at the component level. In exergo-economic analysis, cost of each exergy stream is determined. Inlet and outlet exergy streams of the each component are associated to a monetary cost. This is essential to detect cost-ineffective processes and identify technical options which could improve the cost effectiveness of the overall energy system. In this study, exergo-economic analysis is applied to an aircraft turboprop engine. Analysis is based on experimental values at low torque condition (240 N m). Main components of investigated turboprop engine are the compressor, the combustor, the gas generator turbine, the free power turbine and the exhaust. Cost balance equations have been formed for all components individually and exergo-economic parameters including cost rates and unit exergy costs have been calculated for each component.

Edge Modeling by Two Blur Parameters in Varying Contrasts.

Science.gov (United States)

Seo, Suyoung

2018-06-01

This paper presents a method of modeling edge profiles with two blur parameters, and estimating and predicting those edge parameters with varying brightness combinations and camera-to-object distances (COD). First, the validity of the edge model is proven mathematically. Then, it is proven experimentally with edges from a set of images captured for specifically designed target sheets and with edges from natural images. Estimation of the two blur parameters for each observed edge profile is performed with a brute-force method to find parameters that produce global minimum errors. Then, using the estimated blur parameters, actual blur parameters of edges with arbitrary brightness combinations are predicted using a surface interpolation method (i.e., kriging). The predicted surfaces show that the two blur parameters of the proposed edge model depend on both dark-side edge brightness and light-side edge brightness following a certain global trend. This is similar across varying CODs. The proposed edge model is compared with a one-blur parameter edge model using experiments of the root mean squared error for fitting the edge models to each observed edge profile. The comparison results suggest that the proposed edge model has superiority over the one-blur parameter edge model in most cases where edges have varying brightness combinations.

Varied overstrain injuries of the vertebral column conditioned by evolution

Energy Technology Data Exchange (ETDEWEB)

Kohlbach, W

1983-08-01

During physiological growth of the juvenile vertebral column, various stages of stability occur which are characterized by the condition of the marginal rim of the vertebral bodies. If the vertebral juvenile column is overstrained, these variations in stability results in a variety of damage to vertebral bodies and vertebral disks. One of these lesions corresponds to Scheuermann's disease (osteochondrosis of vertebral epiphyses in juveniles). Damage of the vertebral column due to overstrain can occur only if the overstrain is applied in upright position. Since Man alone can damage his vertebral column in upright position (as a result of his evolutionary development), Scheuermann's thesis is confirmed that Scheuermann's disease is confined to Man. Spondylolysis/spondylolisthesis is also a damage caused by overstrain. Here, too, the damage can occur only if the load is exercised in upright position, with the exception of a slanted positioning of the intervertebral components.

Varied overstrain injuries of the vertebral column conditioned by evolution

International Nuclear Information System (INIS)

Kohlbach, W.

1983-01-01

During physiological growth of the juvenile vertebral column, various stages of stability occur which are characterized by the condition of the marginal rim of the vertebral bodies. If the vertebral juvenile column is overstrained, these variations in stability results in a variety of damage to vertebral bodies and vertebral disks. One of these lesions corresponds to Scheuermann's disease (osteochondrosis of vertebral epiphyses in juveniles). Damage of the vertebral column due to overstrain can occur only if the overstrain is applied in upright position. Since Man alone can damage his vertebral column in upright position (as a result of his evolutionary development), Scheuermann's thesis is confirmed that Scheuermann's disease is confined to Man. Spondylolysis/spondylolisthesis is also a damage caused by overstrain. Here, too, the damage can occur only if the load is exercised in upright position, with the exception of a slanted positioning of the intervertebral components. (orig.) [de

Comparison of finite-element stress analysis with experimental copper sphere impacts

International Nuclear Information System (INIS)

Frantz, C.E.; Hecker, S.S.; Stout, M.G.; Browning, R.V.

1980-07-01

Three copper spheres were impacted on targets of varying surface finishes at 100 m/s. Impact face friction was varied for each test and the impact was photographed with a high-speed camera. Postimpact strains and deformation were measured. A finite-element computer code, NONSAP, was used to model the impact. The best agreement between computer prediction and experiment was obtained using isoparametric elements, a graded mesh, and actual high-strain-rate copper stress-strain data. Frictional conditions at the impact face were also modeled by altering the standard NONSAP code. The most critical test of NONSAP was accurate prediction of experimental impact strains. The best agreement we could obtain had a maximum point-to-point error of 20%, although in general, the comparison was much better. Results of this research indicate that we must know more about material and impact interface friction in order to obtain reliable numerical predictions

Effects of chlorpyrifos in freshwater model ecosystems: the influence of experimental conditions on ecotoxicological thresholds.

Science.gov (United States)

van Wijngaarden, René P A; Brock, Theo C M; Douglas, Mark T

2005-10-01

Three experiments were conducted to determine the impact of the insecticide chlorpyrifos (single applications of 0.01 to 10 microg AI litre(-1)) in plankton-dominated nutrient-rich microcosms. The microcosms (water volume approximately 14 litres) were established in the laboratory under temperature, light regimes and nutrient levels that simulated cool 'temperate' and warm 'Mediterranean' environmental conditions. The fate of chlorpyrifos in the water column was monitored and the effects on zooplankton, phytoplankton and community metabolism were followed for 4 or 5 weeks. The mean half-life (t1/2) of chlorpyrifos in the water of the test systems was 45 h under 'temperate' conditions and about 30 h under 'Mediterranean' environmental conditions. Microcrustaceans (cladocerans and copepod nauplii) were amongst the most sensitive organisms. All three experiments yielded community NOEC (no observed effect concentrations) of 0.1 microg AI litre(-1), similar to those derived from more complex outdoor studies. Above this threshold level, responses and effect chains, and time spans for recovery, differed between the experiments. For example, algal blooms as an indirect effect from the impact of exposure on grazing organisms were only observed under the 'Mediterranean' experimental conditions. The relatively simple indoor test system seems to be sufficient to provide estimates of safe threshold levels for the acute insecticidal effects of low-persistence compounds such as chlorpyrifos. The robustness of the community NOEC indicates that this threshold level is likely to be representative for many freshwater systems. Copyright (c) 2005 Society of Chemical Industry.

Comparison of particle-wall interaction boundary conditions in the prediction of cyclone collection efficiency in computational fluid dynamics (CFD) modeling

International Nuclear Information System (INIS)

Valverde Ramirez, M.; Coury, J.R.; Goncalves, J.A.S.

2009-01-01

In recent years, many computational fluid dynamics (CFD) studies have appeared attempting to predict cyclone pressure drop and collection efficiency. While these studies have been able to predict pressure drop well, they have been only moderately successful in predicting collection efficiency. Part of the reason for this failure has been attributed to the relatively simple wall boundary conditions implemented in the commercially available CFD software, which are not capable of accurately describing the complex particle-wall interaction present in a cyclone. According, researches have proposed a number of different boundary conditions in order to improve the model performance. This work implemented the critical velocity boundary condition through a user defined function (UDF) in the Fluent software and compared its predictions both with experimental data and with the predictions obtained when using Fluent's built-in boundary conditions. Experimental data was obtained from eight laboratory scale cyclones with varying geometric ratios. The CFD simulations were made using the software Fluent 6.3.26. (author)

Time-varying coefficient estimation in SURE models. Application to portfolio management

DEFF Research Database (Denmark)

Casas, Isabel; Ferreira, Eva; Orbe, Susan

This paper provides a detailed analysis of the asymptotic properties of a kernel estimator for a Seemingly Unrelated Regression Equations model with time-varying coefficients (tv-SURE) under very general conditions. Theoretical results together with a simulation study differentiates the cases...

Volitional components of consciousness vary across wakefulness, dreaming and lucid dreaming

NARCIS (Netherlands)

Dresler, M.; Eibl, L.; Fischer, C.F.; Wehrle, R.; Spoormaker, V.I.; Steiger, A.; Czisch, M.; Pawlowski, M.

2014-01-01

Consciousness is a multifaceted concept; its different aspects vary across species, vigilance states, or health conditions. While basal aspects of consciousness like perceptions and emotions are present in many states and species, higher-order aspects like reflective or volitional capabilities seem

Looking for the best experimental conditions to detail the protein solvation shell in a binary aqueous solvent via small angle scattering

International Nuclear Information System (INIS)

Ortore, Maria Grazia; Sinibaldi, Raffaele; Spinozzi, Francesco; Carbini, Andrea; Carsughi, Flavio; Mariani, Paolo

2009-01-01

Protein hydration features attract particular interest in different fields, from biology up to physics, crossing chemistry and medicine. Particular attention is devoted to proteins dissolved in binary aqueous mixtures, since the presence of cosolvent can induce modifications in structural and functional properties. We have recently developed a methodology to obtain a quantitative description on protein solvation shell by a set of in-solution small angle scattering experiments, simultaneously analysed by a global-fit approach. In this paper, numerical simulations of small angle scattering curves are presented to figure out the sensitivity of the technique to different experimental conditions. Simulations concern two model proteins of different molecular weights and an unique cosolvent. A reliability test is introduced in order to find the best experimental conditions to be investigated, together with the most suitable scattering probe (neutrons or X-rays).

Experimental study of the initial conditions of the Rayleigh-Taylor instability at the ablation front in inertial confinement fusion

International Nuclear Information System (INIS)

Delorme, Barthelemy

2015-01-01

Numerous designs and experiments in the domain of Inertial Confinement Fusion (ICF) show that, in both direct and indirect drive approaches, one of the main limitations to reach the ignition is the Rayleigh-Taylor instability (RTI). It may lead to shell disruption and performance degradation of spherically imploding targets. Thus, the understanding and the control of the initial conditions of the RTI is of crucial importance for the ICF program. In this thesis, we present an experimental and theoretical study of the initial conditions of the ablative RTI in direct drive, by means of two experimental campaigns performed on the OMEGA laser facility (LLE, Rochester). The first campaign consisted in studying the laser-imprinted ablative Richtmyer-Meshkov instability (RMI) which starts at the beginning of the interaction and seeds the ablative RTI. We set up an experimental configuration that allowed to measure for the first time the temporal evolution of the laser-imprinted ablative RMI. The experimental results have been interpreted by a theoretical model and numerical simulations performed with the hydrodynamic code CHIC. We show that the best way to control the ablative RMI is to reduce the laser intensity inhomogeneities. This can be achieved with targets covered by a layer of a low density foam. Thus, in the second campaign, we studied for the first time the effect of underdense foams on the growth of the ablative RTI. A layer of low density foam was placed in front of a plastic foil, and the perturbation was imprinted by an intensity modulated laser beam. Experimental data are presented: backscattered laser energy, target dynamic obtained by side-on self emission measurement, and face-on radiographs showing the effect of the foams on the target areal density modulations. These data were interpreted using the CHIC code and the laser-plasma interaction code PARAX. We show that the foams noticeably reduce the amplitude of the laser intensity inhomogeneities and the

Using the power balance model to simulate cross-country skiing on varying terrain.

Science.gov (United States)

Moxnes, John F; Sandbakk, Oyvind; Hausken, Kjell

2014-01-01

The current study adapts the power balance model to simulate cross-country skiing on varying terrain. We assumed that the skier's locomotive power at a self-chosen pace is a function of speed, which is impacted by friction, incline, air drag, and mass. An elite male skier's position along the track during ski skating was simulated and compared with his experimental data. As input values in the model, air drag and friction were estimated from the literature based on the skier's mass, snow conditions, and speed. We regard the fit as good, since the difference in racing time between simulations and measurements was 2 seconds of the 815 seconds racing time, with acceptable fit both in uphill and downhill terrain. Using this model, we estimated the influence of changes in various factors such as air drag, friction, and body mass on performance. In conclusion, the power balance model with locomotive power as a function of speed was found to be a valid tool for analyzing performance in cross-country skiing.

Experimental study on the heat transfer of MWCNT/water nanofluid flowing in a car radiator

International Nuclear Information System (INIS)

Oliveira, Guilherme Azevedo; Cardenas Contreras, Edwin Martin; Bandarra Filho, Enio Pedone

2017-01-01

This study is concerned with an experimental evaluation of the thermal performance of multi-walled carbon nanotubes (MWCNT) dispersed in distilled water flowing inside an automotive radiator. A two-step method called high-pressure homogenization was used to disperse the MWCNT nanoparticles in water, in concentrations varying between 0.05 and 0.16 wt%. Experiments have been carried out in an experimental set up composed by a wind tunnel that simulates the air flow through a car radiator, and a hot fluid circuit, that circulates the nanofluid inside the radiator. The air flow rate was maintained constant at 0.175 kg/s. The mass flow rate of the hot fluid varied from 30 up to 70 g/s and the inlet temperature was maintained constant at 50, 60, 70 and 80 °C, respectively. The temperature drop and heat transfer rate have been investigated. A slight-decrease on the heat transfer rate, up to 5%, was found for all test conditions. On the other hand as the nanoparticle concentration increased, the heat transfer rate decreased.

Relationship between continuity of care and adverse outcomes varies by number of chronic conditions among older adults with diabetes

Directory of Open Access Journals (Sweden)

Eva H. DuGoff

2016-06-01

Full Text Available Follow us on Twitter Co-Editors-in-Chief Martin Fortin Jane Gunn Stewart W. Mercer Susan Smith Marjan van den Akker Society for Academic Primary Care Journal Help USER You are logged in as... avalster My Profile Log Out JOURNAL CONTENT Search Search Scope Search Browse By Issue By Author By Title By Sections By Identify Types OPEN JOURNAL SYSTEMS FONT SIZE Make font size smallerMake font size defaultMake font size larger INFORMATION For Readers For Authors For Librarians ARTICLE TOOLS Print this article Indexing metadata How to cite item Supplementary files Finding References Email this article Email the author Post a Comment NOTIFICATIONS View (378 new Manage IRCMO NEWS ‘Addressing the global challenge of... Publications on multimorbidity... The CARE Plus study Prevalence of multimorbidity in the... Multimorbidity in adults from a... CURRENT ISSUE Atom logo RSS2 logo RSS1 logo HOSTED BY Part of the PKP Publishing Services Network HOME ABOUT USER HOME SEARCH CURRENT ARCHIVES ANNOUNCEMENTS PUBLISHER AUTHOR GUIDELINES SUBMISSIONS WHY PUBLISH WITH US? Home > Vol 6, No 2 (2016 >\tDuGoff Relationship between continuity of care and adverse outcomes varies by number of chronic conditions among older adults with diabetes Eva H. DuGoff, Karen Bandeen-Roche, Gerard F. Anderson Abstract Background: Continuity of care is a basic tenant of primary care practice. However, the evidence on the importance of continuity of care for older adults with complex conditions is mixed. Objective: To assess the relationship between measurement of continuity of care, number of chronic conditions, and health outcomes. Design: We analyzed data from a cohort of 1,600 US older adults with diabetes and ≥1 other chronic condition in a private Medicare health plan from July 2010 to December 2011. Multivariate regression models were used to examine the association of baseline continuity (the first 6 months and the composite outcome of any emergency room use or inpatient

Varied overstrain injuries of the vertebral column conditioned by evolution

Energy Technology Data Exchange (ETDEWEB)

Kohlbach, W.

1983-08-01

During physiological growth of the juvenile vertebral column, various stages of stability occur which are characterized by the condition of the marginal rim of the vertebral bodies. If the vertebral juvenile column is overstrained, these variations in stability results in a variety of damage to vertebral bodies and vertebral disks. One of these lesions corresponds to Scheuermann's disease (osteochondrosis of vertebral epiphyses in juveniles). Damage of the vertebral column due to overstrain can occur only if the overstrain is applied in upright position. Since Man alone can damage his vertebral column in upright position (as a result of his evolutionary development), Scheuermann's thesis is confirmed that Scheuermann's disease is confined to Man. Spondylolysis/spondylolisthesis is also a damage caused by overstrain. Here, too, the damage can occur only if the load is exercised in upright position, with the exception of a slanted positioning of the intervertebral components.

Experimental studies of flow induced vibrations of the fuel assembly for the PEC reactor

International Nuclear Information System (INIS)

Pitimada, D.; Presaghi, M.; Tampone, O.; Cesari, F.

1977-01-01

The vibration behaviour of an assembly of seven mock-up fuel bundles of PEC reactor has been investigated. The assembly was excited by a parallel flow of water simulating sodium. The motion of the group (or of a single bundle in the group) has been measured in transverse sections detecting two orthogonal components of displacement. During the experiences the following parameters were varied: bundle foot and pads restraints, flow rate condition, coolant flow outlet conditions at the head of fuel bundles. Experimental data were processed in order to obtain: trajectories of three points of fuel bundle axis, power density spectra of measured vibration amplitudes, correlations between coolant flow rate and vibration amplitude R.M.S. (author)

Tribological and Wear Performance of Carbide Tools with TiB2 PVD Coating under Varying Machining Conditions of TiAl6V4 Aerospace Alloy

Directory of Open Access Journals (Sweden)

Jose Mario Paiva

2017-11-01

Full Text Available Tribological phenomena and tool wear mechanisms during machining of hard-to-cut TiAl6V4 aerospace alloy have been investigated in detail. Since cutting tool wear is directly affected by tribological phenomena occurring between the surfaces of the workpiece and the cutting tool, the performance of the cutting tool is strongly associated with the conditions of the machining process. The present work shows the effect of different machining conditions on the tribological and wear performance of TiB2-coated cutting tools compared to uncoated carbide tools. FEM modeling of the temperature profile on the friction surface was performed for wet machining conditions under varying cutting parameters. Comprehensive characterization of the TiB2 coated vs. uncoated cutting tool wear performance was made using optical 3D imaging, SEM/EDX and XPS methods respectively. The results obtained were linked to the FEM modeling. The studies carried out show that during machining of the TiAl6V4 alloy, the efficiency of the TiB2 coating application for carbide cutting tools strongly depends on cutting conditions. The TiB2 coating is very efficient under roughing at low speeds (with strong buildup edge formation. In contrast, it shows similar wear performance to the uncoated tool under finishing operations at higher cutting speeds when cratering wear predominates.

Identification of Time-Varying Pilot Control Behavior in Multi-Axis Control Tasks

Science.gov (United States)

Zaal, Peter M. T.; Sweet, Barbara T.

2012-01-01

Recent developments in fly-by-wire control architectures for rotorcraft have introduced new interest in the identification of time-varying pilot control behavior in multi-axis control tasks. In this paper a maximum likelihood estimation method is used to estimate the parameters of a pilot model with time-dependent sigmoid functions to characterize time-varying human control behavior. An experiment was performed by 9 general aviation pilots who had to perform a simultaneous roll and pitch control task with time-varying aircraft dynamics. In 8 different conditions, the axis containing the time-varying dynamics and the growth factor of the dynamics were varied, allowing for an analysis of the performance of the estimation method when estimating time-dependent parameter functions. In addition, a detailed analysis of pilots adaptation to the time-varying aircraft dynamics in both the roll and pitch axes could be performed. Pilot control behavior in both axes was significantly affected by the time-varying aircraft dynamics in roll and pitch, and by the growth factor. The main effect was found in the axis that contained the time-varying dynamics. However, pilot control behavior also changed over time in the axis not containing the time-varying aircraft dynamics. This indicates that some cross coupling exists in the perception and control processes between the roll and pitch axes.

On the scaling limits of Galton Watson processes in varying environment

NARCIS (Netherlands)

Bansaye, V.; Simatos, F.

2011-01-01

Renormalized sequences of Galton Watson processes converge to Continuous State Branching Processes (CSBP), characterized by a L\\'evy triplet of two numbers and a measure. This paper investigates the case of Galton Watson processes in varying environment and provides an explicit sufficient condition

Buckling of Nonprismatic Column on Varying Elastic Foundation with Arbitrary Boundary Conditions

Directory of Open Access Journals (Sweden)

Ahmad A. Ghadban

2017-01-01

Full Text Available Buckling of nonprismatic single columns with arbitrary boundary conditions resting on a nonuniform elastic foundation may be considered as the most generalized treatment of the subject. The buckling differential equation for such columns is extremely difficult to solve analytically. Thus, the authors propose a numerical approach by discretizing the column into a finite number of segments. Each segment has constants E (modulus of elasticity, I (moment of inertia, and β (subgrade stiffness. Next, an exact analytical solution is derived for each prismatic segment resting on uniform elastic foundation. These segments are then assembled in a matrix from which the critical buckling load is obtained. The derived formulation accounts for different end boundary conditions. Validation is performed by benchmarking the present results against analytical solutions found in the literature, showing excellent agreement. After validation, more examples are solved to illustrate the power and flexibility of the proposed method. Overall, the proposed method provides reasonable results, and the examples solved demonstrate the versatility of the developed approach and some of its many possible applications.

Experimental and numerical study on single-phase flow characteristics of natural circulation system with heated narrow rectangular channel under rolling motion condition

International Nuclear Information System (INIS)

Yu, Shengzhi; Wang, Jianjun; Yan, Ming; Yan, Changqi; Cao, Xiaxin

2017-01-01

Highlights: • The phasic difference between flow rate and frictional pressure drop is negligible. • Effect mechanism of rolling motion on flow behaviors of NC is interpreted. • The startup model is proposed and verified. • Steady-state correlations are feasible to predict transient resistance. • The in-house code can simulate instantaneous flow behaviors of NC correctly. - Abstract: Effects of rolling motion on flow characteristics in a natural circulation system were investigated experimentally and numerically. The numerical results from validated code were mainly used to provide detailed information for the discussion and analysis of experimental results. The results indicate that under rolling motion condition, the phasic difference between flow rate and frictional pressure drop of narrow rectangular channel is negligible. Angular acceleration is the eigenvalue for the effects of rolling motion on flow rate under single-phase natural circulation condition. When angular acceleration is approximately equal, even though either the angle or the period of rolling motion is different, peak, trough and time-averaged values of flow rate are approximately equal. Under rolling motion and single-phase natural circulation conditions, the phenomenon that dimensionless time-averaged mass flow rate is smaller than that under steady state condition is controlled by the nonlinear relationship between mass flow rate and the resistance of loop. The factor also causes the result that the absolute difference of dimensionless flow rate between peak and steady state is smaller than that between trough and steady state. The startup model which is proposed in present paper can be used to predict the flow characteristics of single-phase natural circulation system at startup stage of rolling motion favorably. The self-developed code can simulate instantaneous flow characteristics of single-phase natural circulation system under rolling motion and steady state conditions

Experimental study of the mechanisms of CO2 capture by calcium cycle under circulating fluidized bed conditions

International Nuclear Information System (INIS)

Hoteit, A.

2006-06-01

The work undertaken in this Thesis in partnership with department R and D of ALSTOM Power Boilers, CEMEX and the ADEME, relates to the experimental study of various phenomena associated to CO 2 capture under circulating fluidized bed conditions. The size of particles, temperature and the CO 2 concentration have an influence on the limestone calcination reaction. The reaction of carbonation of lime is not total. During successive cycles of calcination/carbonation, the rate of carbonation obtained with hydrated lime is increasingly higher than that obtained with the lime. Under continuously reducing conditions, the decomposition of sulphates present in the bed ashes is not total. This decomposition is total under reduction/oxidation cycles. A modeling of calcination allowed to determine the intrinsic kinetic constants of calcination and carbonation. (author)

Attenuation of organic micropollutants in an urban lowland stream under varying seasonal and hydrological conditions

Science.gov (United States)

Jaeger, Anna; Posselt, Malte; Schaper, Jonas; Lewandowski, Jörg

2017-04-01

Transport and fate of polar organic micropollutants in urban streams are of increasing concern for urban water management. Appropriate river management techniques may support a river's ability to self-purify. The river Erpe, an urban lowland stream located in Berlin, Germany, receives treated wastewater which increases its discharge up to 4-fold. Numerous micropollutants (e.g. pharmaceuticals, personal care products, performance chemicals) which survive the treatment process are released into the river and threaten ecosystems and aquatic groundwater quality. In the present work the transport of 57 substances was investigated along a 4.7 km stretch of the river with the aim of understanding the influence of varying seasonal and hydrological conditions on micropollutant fate. We hypothesized that particularly transient storage is a main driver of micropollutant attenuation. A Lagrangian sampling scheme was applied to follow water parcels down the river using the diurnal fluctuations of conservative solute concentrations as an intrinsic tracer. Water samples were collected at two (April) and three (June) stations along a 4.7 km reach downstream of the wastewater inflow. In June the experiment was conducted twice, before and after the first stretch was cleared of macrophytes. Each experiment comprised of hourly sample collection for 48 hours, accompanied by discharge measurements and continuous data logging of water-level, -temperature and electric conductivity. The set of micropollutants, which included both parent compounds and transformation products, was analysed by a newly developed direct injection-UHPLC-MS/MS method. The behaviour of individual micropollutants was compound-specific. Carbamazepine and benzotriazole were persistent along the river stretch while substances such as valsartan and metoprolol were attenuated by up to 15% of their original concentration. Interestingly, some transformation products, such as valsartan acid increased in concentration

Exponential stability of switched linear systems with time-varying delay

Directory of Open Access Journals (Sweden)

Satiracoo Pairote

2007-11-01

Full Text Available We use a Lyapunov-Krasovskii functional approach to establish the exponential stability of linear systems with time-varying delay. Our delay-dependent condition allows to compute simultaneously the two bounds that characterize the exponential stability rate of the solution. A simple procedure for constructing switching rule is also presented.

An integrative time-varying frequency detection and channel sounding method for dynamic plasma sheath

Science.gov (United States)

Shi, Lei; Yao, Bo; Zhao, Lei; Liu, Xiaotong; Yang, Min; Liu, Yanming

2018-01-01

The plasma sheath-surrounded hypersonic vehicle is a dynamic and time-varying medium and it is almost impossible to calculate time-varying physical parameters directly. The in-fight detection of the time-varying degree is important to understand the dynamic nature of the physical parameters and their effect on re-entry communication. In this paper, a constant envelope zero autocorrelation (CAZAC) sequence based on time-varying frequency detection and channel sounding method is proposed to detect the plasma sheath electronic density time-varying property and wireless channel characteristic. The proposed method utilizes the CAZAC sequence, which has excellent autocorrelation and spread gain characteristics, to realize dynamic time-varying detection/channel sounding under low signal-to-noise ratio in the plasma sheath environment. Theoretical simulation under a typical time-varying radio channel shows that the proposed method is capable of detecting time-variation frequency up to 200 kHz and can trace the channel amplitude and phase in the time domain well under -10 dB. Experimental results conducted in the RF modulation discharge plasma device verified the time variation detection ability in practical dynamic plasma sheath. Meanwhile, nonlinear phenomenon of dynamic plasma sheath on communication signal is observed thorough channel sounding result.

Seed banks as a source of vegetation regeneration to support the recovery of degraded rivers: A comparison of river reaches of varying condition.

Science.gov (United States)

O'Donnell, Jessica; Fryirs, Kirstie A; Leishman, Michelle R

2016-01-15

Anthropogenic disturbance has contributed to widespread geomorphic adjustment and the degradation of many rivers. This research compares for river reaches of varying condition, the potential for seed banks to support geomorphic river recovery through vegetation regeneration. Seven river reaches in the lower Hunter catchment of south-eastern Australia were assessed as being in poor, moderate, or good condition, based on geomorphic and ecological indicators. Seed bank composition within the channel and floodplain (determined in a seedling emergence study) was compared to standing vegetation. Seed bank potential for supporting geomorphic recovery was assessed by measuring native species richness, and the abundance of different plant growth forms, with consideration of the roles played by different growth forms in geomorphic adjustment. The exotic seed bank was considered a limiting factor for achieving ecological restoration goals, and similarly analysed. Seed bank native species richness was comparable between the reaches, and regardless of condition, early successional and pioneer herbs, sedges, grasses and rushes dominated the seed bank. The capacity for these growth forms to colonise and stabilise non-cohesive sediments and initiate biogeomorphic succession, indicates high potential for the seed banks of even highly degraded reaches to contribute to geomorphic river recovery. However, exotic propagules increasingly dominated the seed banks of moderate and poor condition reaches and reflected increasing encroachment by terrestrial exotic vegetation associated with riparian degradation. As the degree of riparian degradation increases, the resources required to control the regeneration of exotic species will similarly increase, if seed bank-based regeneration is to contribute to both geomorphic and ecological restoration goals. Copyright © 2015 Elsevier B.V. All rights reserved.

Analysis of cerebral vessels dynamics using experimental data with missed segments

Science.gov (United States)

Pavlova, O. N.; Abdurashitov, A. S.; Ulanova, M. V.; Shihalov, G. M.; Semyachkina-Glushkovskaya, O. V.; Pavlov, A. N.

2018-04-01

Physiological signals often contain various bad segments that occur due to artifacts, failures of the recording equipment or varying experimental conditions. The related experimental data need to be preprocessed to avoid such parts of recordings. In the case of few bad segments, they can simply be removed from the signal and its analysis is further performed. However, when there are many extracted segments, the internal structure of the analyzed physiological process may be destroyed, and it is unclear whether such signal can be used in diagnostic-related studies. In this paper we address this problem for the case of cerebral vessels dynamics. We perform analysis of simulated data in order to reveal general features of quantifying scaling features of complex signals with distinct correlation properties and show that the effects of data loss are significantly different for experimental data with long-range correlations and anti-correlations. We conclude that the cerebral vessels dynamics is significantly less sensitive to missed data fragments as compared with signals with anti-correlated statistics.

Variability of the morphometric features of Calliphora vicina (Diptera, Calliphoridae under the varying and constant micro-climatic condi-tions

Directory of Open Access Journals (Sweden)

L. I. Faly

2013-03-01

Full Text Available Variability of the main morphometric features of imago flies Calliphora vicina R.-D. (Diptera, Calliphoridae of two samples was studied. First sample consists of individuals caught in the wild (park ecosystems of Dnipropetrovsk, the second one – specimens cultured in the laboratory under the constant temperature and humidity. Possible using of C. vicina R.-D. as a bioindicator of anthropogenic factors is analysed. Environmental factors may act as the stimulators of adaptive changes in physiological functions, as the constraints that cause impossibility of the existence of certain species in particular conditions, and as modifiers that determine the morpho- anatomical and physiological changes in organisms. The most significant differences between studied samples were found for the width (“laboratory” individuals are characterized by larger head size and for the length of limbs segments. The fluctuating range of the head width in specimens collected in the wild is much wider, due to the heterogeneity of the micro-climatic conditions of the larvae development and trophic resources. Maximal negative asymmetry of the head width is observed in individuals C. vicina R.-D. of the “natural” sample as compared with “laboratory” individuals. Among imagoes caught in the wild the individuals with a relatively wide head are dominated, as evidenced by the large positive value of kurtosis. At the same time, the distribution of values in “laboratory” individuals is almost normal. In adults bred in the laboratory the shortening of segments of the leg pair I is observed in comparison with the individuals of “natural” sample. Similar results were recorded for other insect groups cultivated in a laboratory. For most other linear measurements of the C. vicina R.-D. body the differences between samples are not registered. Ephemeral existence of the substrate of blow flies leads to higher prevailing evolutionary adaptation of species to varying

Conditional Correlation Models of Autoregressive Conditional Heteroskedasticity with Nonstationary GARCH Equations

DEFF Research Database (Denmark)

Amado, Cristina; Teräsvirta, Timo

-run and the short-run dynamic behaviour of the volatilities. The structure of the conditional correlation matrix is assumed to be either time independent or to vary over time. We apply our model to pairs of seven daily stock returns belonging to the S&P 500 composite index and traded at the New York Stock Exchange......In this paper we investigate the effects of careful modelling the long-run dynamics of the volatilities of stock market returns on the conditional correlation structure. To this end we allow the individual unconditional variances in Conditional Correlation GARCH models to change smoothly over time...... by incorporating a nonstationary component in the variance equations. The modelling technique to determine the parametric structure of this time-varying component is based on a sequence of specification Lagrange multiplier-type tests derived in Amado and Teräsvirta (2011). The variance equations combine the long...

Experimental and numerical investigation of the mixed-mode delamination in Arcan laminated specimens

International Nuclear Information System (INIS)

Choupani, Naghdali

2008-01-01

This paper investigates mixed-mode interlaminar fracture behaviour in woven carbon fibre/polyetherimide (CF/PEI) thermoplastic composite material based on experimental and numerical analyses. Experiments were conducted on modified Arcan specimens using the special test loading device. By varying the loading angle from 0 o to 90 o , pure mode-I, pure mode-II and a wide range of mixed-mode data were obtained experimentally. Using the finite-element results, correction factors were applied to the CF/PEI fracture specimen. By employing experimentally measured critical loads and the aid of the finite-element method, mixed-mode interlaminar fracture toughness for the composite under consideration determined. The failure response of CF/PEI composite was compared to the different mixed-mode failure criteria, and the best criterion was selected. The fracture surfaces of the CF/PEI composite under different mixed-mode loading conditions were examined by optical and scanning electron microscopy to gain insight into the failure responses

Cognitive load and task condition in event- and time-based prospective memory: an experimental investigation.

Science.gov (United States)

Khan, Azizuddin; Sharma, Narendra K; Dixit, Shikha

2008-09-01

Prospective memory is memory for the realization of delayed intention. Researchers distinguish 2 kinds of prospective memory: event- and time-based (G. O. Einstein & M. A. McDaniel, 1990). Taking that distinction into account, the present authors explored participants' comparative performance under event- and time-based tasks. In an experimental study of 80 participants, the authors investigated the roles of cognitive load and task condition in prospective memory. Cognitive load (low vs. high) and task condition (event- vs. time-based task) were the independent variables. Accuracy in prospective memory was the dependent variable. Results showed significant differential effects under event- and time-based tasks. However, the effect of cognitive load was more detrimental in time-based prospective memory. Results also revealed that time monitoring is critical in successful performance of time estimation and so in time-based prospective memory. Similarly, participants' better performance on the event-based prospective memory task showed that they acted on the basis of environment cues. Event-based prospective memory was environmentally cued; time-based prospective memory required self-initiation.

Analytical and experimental investigation of chlorine decay in water supply systems under unsteady hydraulic conditions

DEFF Research Database (Denmark)

Aisopou, Angeliki; Stoianov, Ivan; Graham, Nigel

2013-01-01

This paper investigates the impact of the dynamic hydraulic conditions on the kinetics of chlorine decay in water supply systems. A simulation framework has been developed for the scale-adaptive hydraulic and chlorine decay modelling under steady- and unsteady-state flows. An unsteady decay coeff...... of experimental data provides new insights for the near real-time modelling and management of water quality as well as highlighting the uncertainty and challenges of accurately modelling the loss of disinfectant in water supply networks.......This paper investigates the impact of the dynamic hydraulic conditions on the kinetics of chlorine decay in water supply systems. A simulation framework has been developed for the scale-adaptive hydraulic and chlorine decay modelling under steady- and unsteady-state flows. An unsteady decay...... coefficient is defined which depends upon the absolute value of shear stress and the rate of change of shear stress for quasi-unsteady and unsteady-state flows. By coupling novel instrumentation technologies for continuous hydraulic monitoring and water quality sensors for in-pipe water quality sensing...

[Effect of vitamin C on the condition of NO-synthase system in experimental stomach ulcer].

Science.gov (United States)

Zhuroms'kyĭ, V S; Skliarov, O Ia

2011-01-01

We investigated the effect of Vitamin C (Vit C) on the changes of activity of the enzymes of NO-synthase system, nitric oxide content, lipoperoxidation processes, activity of SOD and catalase in gastric mucosa (GM), and concentrations of L-arginine, Vit C and Vit E in the blood of rats under conditions of experimental ulcer of the stomach caused by adrenaline injection. Vit C displayed a pronounced antioxidant action, reduced the degree of destructive affections, diminished the activity of iNOS and lipoperoxidation processes, decreased the NO content and SOD activity. Furthermore, the concentration of L-arginine and Vit C in the blood was increased. Combined action of Vit C with L-arginine reduced the degree of GM lesions, activity of eNOS and the content of NO in GM whereas the concentration of L-arginine in blood was increased. Under conditions of Vit C action and iNOS and COX-2 blockage, the activity of NO-synthases and lipoperoxidation processes were slightly decreased, indicating on dominant action of Vit C.

Out-of-plane vibrations of inhomogeneous curved bars having varying cross-sections

International Nuclear Information System (INIS)

Suzuki, Katsuyoshi; Kosawada, Tadashi

1987-01-01

An exact method using power series expansions is presented for solving out-of-plane free vibrations of inhomogeneous curved bars with varying curvatures and cross-sections. Equations of motion and boundary conditions are derived from the stationary conditions of the Lagrangian of curved bars. Natural frequencies and mode shapes are presented for elliptical and circular arc bars having both ends clamped and clamped-free ends. (author)

Experimental studies on mitigation of LOCA for a high flux research reactor

International Nuclear Information System (INIS)

Saxena, A.K.

2006-01-01

Experimental studies on the rewetting behaviour of hot vertical annular channels were performed to study the mitigation of consequences of loss of coolant accident (LOCA) for a high flux research reactor. Studies were carried out to study the rewetting behaviour with hot inner tube, for bottom flooding and top flow rewetting conditions. The tube was made of stainless steel. Experiments were conducted for water flow rates in the annulus upto 7 litres per minute (l pm) (11.7 x 10 -5 m 3 s -1 ). The initial surface temperature of the inner tube was varied from 200 to 500 degC. (author)

Delineamento experimental e tamanho de amostra para alface cultivada em hidroponia Experimental design and sample size for hydroponic lettuce crop

Directory of Open Access Journals (Sweden)

Valéria Schimitz Marodim

2000-10-01

Full Text Available Este estudo visa a estabelecer o delineamento experimental e o tamanho de amostra para a cultura da alface (Lactuca sativa em hidroponia, pelo sistema NFT (Nutrient film technique. O experimento foi conduzido no Laboratório de Cultivos Sem Solo/Hidroponia, no Departamento de Fitotecnia da Universidade Federal de Santa Maria e baseou-se em dados de massa de plantas. Os resultados obtidos mostraram que, usando estrutura de cultivo de alface em hidroponia sobre bancadas de fibrocimento com seis canais, o delineamento experimental adequado é blocos ao acaso se a unidade experimental for constituída de faixas transversais aos canais das bancadas, e deve ser inteiramente casualizado se a bancada for a unidade experimental; para a variável massa de plantas, o tamanho da amostra é de 40 plantas para uma semi-amplitude do intervalo de confiança em percentagem da média (d igual a 5% e de 7 plantas para um d igual a 20%.This study was carried out to establish the experimental design and sample size for hydroponic lettuce (Lactuca sativa crop under nutrient film technique. The experiment was conducted in the Laboratory of Hydroponic Crops of the Horticulture Department of the Federal University of Santa Maria. The evaluated traits were plant weight. Under hydroponic conditions on concrete bench with six ducts, the most indicated experimental design for lettuce is randomised blocks for duct transversal plots or completely randomised for bench plot. The sample size for plant weight should be 40 and 7 plants, respectively, for a confidence interval of mean percentage (d equal to 5% and 20%.

An analytical and experimental approach for pressure distribution analysis of a particular lobe and plain bearing performance keeping in view of all impeding varying parameters associating with fixed lubrication SAE20W40

International Nuclear Information System (INIS)

Biswas, Nabarun; Chakraborti, Prasun; Belkar, Sanjay

2016-01-01

This paper presents both analytical and experimental pressure analysis approach of a typical Lobe and plain bearing for determining effective performance of the bearing. This is found to be dependent on several variables viz. angular velocity (1200-1900 rpm), load (300- 750 N) and pressure angle (0.deg.-180.deg.). This study in particular has been carried out for better rectifications and comparative prediction of lobe and plain bearing in terms of pressure distribution behavior under lubrication oil grade of SAE20W40. Influencing parameters were varied in this set up only to get optimum parametric combination considering all relevant practical issues. The experimentation was done based on significant directives of relevant literatures in these sectors. Attempt was made to compare the analytical findings with experimental results and found matched appreciably. After that attention was diverted to find the nature of pressure and load carrying capacity at various fluctuating speed and load with a fixed lubrication of SAE20W40 for appropriate decision making towards its characteristic performance. The analytical data generated by MATLAB are compared with experimental data which is generated by JBTR

An analytical and experimental approach for pressure distribution analysis of a particular lobe and plain bearing performance keeping in view of all impeding varying parameters associating with fixed lubrication SAE20W40

Energy Technology Data Exchange (ETDEWEB)

Biswas, Nabarun; Chakraborti, Prasun [National Institute of Technology Agartala, Jirania (India); Belkar, Sanjay [Pravara Rural Engineering CollegeLoni, Rahata taluka (India)

2016-05-15

This paper presents both analytical and experimental pressure analysis approach of a typical Lobe and plain bearing for determining effective performance of the bearing. This is found to be dependent on several variables viz. angular velocity (1200-1900 rpm), load (300- 750 N) and pressure angle (0.deg.-180.deg.). This study in particular has been carried out for better rectifications and comparative prediction of lobe and plain bearing in terms of pressure distribution behavior under lubrication oil grade of SAE20W40. Influencing parameters were varied in this set up only to get optimum parametric combination considering all relevant practical issues. The experimentation was done based on significant directives of relevant literatures in these sectors. Attempt was made to compare the analytical findings with experimental results and found matched appreciably. After that attention was diverted to find the nature of pressure and load carrying capacity at various fluctuating speed and load with a fixed lubrication of SAE20W40 for appropriate decision making towards its characteristic performance. The analytical data generated by MATLAB are compared with experimental data which is generated by JBTR.

Rimsulfuron in Soil: Effects on Microbiological Properties under Varying Soil Conditions

Directory of Open Access Journals (Sweden)

Ljiljana Radivojević

2011-01-01

Full Text Available The effects of rimsulfuron a sulfonylurea herbicide on the growth and activity of soil microorganisms under laboratory conditions was investigated in two soils. The application rates were: 0.2, 2.0 and 20.0 mg a.i kg-1 soil. The lowest concentration tested was the label rate (0.2 mg a.i kg-1, and the other two were ten and hundred timeshigher. No adverse effects on microbiological processes were observed for the label rate. Decrease in microbial biomass carbon, dehydrogenase activity, fungi and bacteria in comparison with untreated control, were found at higher rates. The magnitude of these effects were generally slight and transitory.

Experimental determination of drift and PM10 cooling tower emissions: Influence of components and operating conditions.

Science.gov (United States)

Ruiz, J; Kaiser, A S; Lucas, M

2017-11-01

Cooling tower emissions have become an increasingly common hazard to the environment (air polluting, ice formation and salts deposition) and to the health (Legionella disease) in the last decades. Several environmental policies have emerged in recent years limiting cooling tower emissions but they have not prevented an increasing intensity of outbreaks. Since the level of emissions depends mainly on cooling tower component design and the operating conditions, this paper deals with an experimental investigation of the amount of emissions, drift and PM 10 , emitted by a cooling tower with different configurations (drift eliminators and distribution systems) and working under several operating conditions. This objective is met by the measurement of cooling tower source emission parameters by means of the sensitive paper technique. Secondary objectives were to contextualize the observed emission rates according to international regulations. Our measurements showed that the drift rates included in the relevant international standards are significantly higher than the obtained results (an average of 100 times higher) and hence, the environmental problems may occur. Therefore, a revision of the standards is recommended with the aim of reducing the environmental and human health impact. By changing the operating conditions and the distribution system, emissions can be reduced by 52.03% and 82% on average. In the case of drift eliminators, the difference ranges from 18.18% to 98.43% on average. As the emissions level is clearly influenced by operating conditions and components, regulation tests should be referred to default conditions. Finally, guidelines to perform emission tests and a selection criterion of components and conditions for the tested cooling tower are proposed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Experimental substantiation of methodic of 11-13 years old boxers’ coordination development

Directory of Open Access Journals (Sweden)

Yong Qiang Liu

2015-06-01

Full Text Available Purpose: experimental substantiation of methodic of junior boxers’ coordination training. Material: in the research 18 boxers of 11-13 year old age participated. In total, during 4 months 42 trainings were conducted. Total time of coordination load’s fulfillment at each training was 15-45 minutes. Results: dynamic of results in control tests was statistically confident in the tested parameters of movements. It proves effectiveness of usage the tasks with complex-coordination orientation, accented on impact on sensor-informational and motor systems of movements in junior boxers’ trainings. Conclusions: coordination training in boxing at initial stage shall include specialized varied means and methods, which would facilitate formation of motor condition and skills’ basis. Motor condition and skills are a reserve for further rising of coordination abilities’ level of junior sportsmen.

Cooling the vertical surface by conditionally single pulses

Science.gov (United States)

Karpov, Pavel; Nazarov, Alexander; Serov, Anatoly; Terekhov, Victor

2017-10-01

You Sprays with periodic supply of the droplet phase have great opportunities to control the heat exchange processes. Varying pulse duration and frequency of their repetition, we can achieve the optimal conditions of evaporative cooling with minimization of the liquid flow rate. The paper presents experimental data on studying local heat transfer on a large subcooled surface, obtained on the original setup with multinozzle controlled system of impact irrigation by the gas-droplet flow. A contribution to intensification of the spray parameters (flow rate, pulse duration, repetition frequency) per a growth of integral heat transfer was studied. Data on instantaneous distribution of the heat flux value helped us to describe the processes occurring on the studied surface. These data could describe the regime of "island" film cooling.

Experimental evidence of population differences in reproductive investment conditional on environmental stochasticity

Energy Technology Data Exchange (ETDEWEB)

Gauthey, Zoé [INRA, UMR 1224, Ecologie Comportementale et Biologie des Populations de Poissons, Aquapôle, quartier Ibarron, 64310 Saint-Pée sur Nivelle (France); Univ Pau & Pays Adour, UMR 1224, Ecologie Comportementale et Biologie des Populations de Poissons, UFR Sciences et Techniques de la Côte Basque, Allée du parc Montaury, 64600 Anglet (France); Panserat, Stéphane [INRA, UR 107, Nutrition Metabolism Aquaculture, Aquapôle, 64310 Saint Pée sur Nivelle (France); Elosegi, Arturo [Faculty of Science and Technology, University of the Basque Country UPV/EHU, 48080 Bilbao (Spain); Herman, Alexandre [INRA, UR 107, Nutrition Metabolism Aquaculture, Aquapôle, 64310 Saint Pée sur Nivelle (France); Tentelier, Cédric [INRA, UMR 1224, Ecologie Comportementale et Biologie des Populations de Poissons, Aquapôle, quartier Ibarron, 64310 Saint-Pée sur Nivelle (France); Univ Pau & Pays Adour, UMR 1224, Ecologie Comportementale et Biologie des Populations de Poissons, UFR Sciences et Techniques de la Côte Basque, Allée du parc Montaury, 64600 Anglet (France); and others

2016-01-15

Environmental stochasticity is expected to shape life histories of species, wherein organisms subjected to strong environmental variation should display adaptive response by being able to tune their reproductive investment. For riverine ecosystems, climate models forecast an increase in the frequency and intensity of extreme events such as floods and droughts. The speed and the mechanisms by which organisms may adapt their reproductive investment are therefore of primary importance to understand how species will cope with such radical environmental changes. In the present study, we sampled spawners from two different populations of wild brown trout, originating from two environments with contrasting levels of flow stochasticity. We placed them in sympatry within an experimental channel during reproductive season. In one modality, water flow was maintained constant, whereas in another modality, water flow was highly variable. Reproductive investment of all individuals was monitored using weight and energetic plasma metabolite variation throughout the reproductive season. Only the populations originating from the most variable environment showed a plastic response to experimental manipulation of water flow, the females being able to reduce their weight variation (from 19.2% to 13.1%) and metabolites variations (from 84.2% to 18.6% for triglycerides for instance) under variable flow conditions. These results imply that mechanisms to cope with environmental stochasticity can differ between populations of the same species, where some populations can be plastic whereas other cannot. - Highlights: • We place two populations of brown trout under contrasting water flow for reproduction. • Energetic metabolite variation is used as a cue of reproductive investment. • In constant flow, both populations show the same reproductive investment. • In variable flow, only one of the populations modifies its reproductive investment. • Divergent evolution of reproductive

Experimental evidence of population differences in reproductive investment conditional on environmental stochasticity

International Nuclear Information System (INIS)

Gauthey, Zoé; Panserat, Stéphane; Elosegi, Arturo; Herman, Alexandre; Tentelier, Cédric

2016-01-01

Environmental stochasticity is expected to shape life histories of species, wherein organisms subjected to strong environmental variation should display adaptive response by being able to tune their reproductive investment. For riverine ecosystems, climate models forecast an increase in the frequency and intensity of extreme events such as floods and droughts. The speed and the mechanisms by which organisms may adapt their reproductive investment are therefore of primary importance to understand how species will cope with such radical environmental changes. In the present study, we sampled spawners from two different populations of wild brown trout, originating from two environments with contrasting levels of flow stochasticity. We placed them in sympatry within an experimental channel during reproductive season. In one modality, water flow was maintained constant, whereas in another modality, water flow was highly variable. Reproductive investment of all individuals was monitored using weight and energetic plasma metabolite variation throughout the reproductive season. Only the populations originating from the most variable environment showed a plastic response to experimental manipulation of water flow, the females being able to reduce their weight variation (from 19.2% to 13.1%) and metabolites variations (from 84.2% to 18.6% for triglycerides for instance) under variable flow conditions. These results imply that mechanisms to cope with environmental stochasticity can differ between populations of the same species, where some populations can be plastic whereas other cannot. - Highlights: • We place two populations of brown trout under contrasting water flow for reproduction. • Energetic metabolite variation is used as a cue of reproductive investment. • In constant flow, both populations show the same reproductive investment. • In variable flow, only one of the populations modifies its reproductive investment. • Divergent evolution of reproductive

Uniform stability for time-varying infinite-dimensional discrete linear systems

International Nuclear Information System (INIS)

Kubrusly, C.S.

1988-09-01

Stability for time-varying discrete linear systems in a Banach space is investigated. On the one hand, it established a fairly complete collection of necessary and sufficient conditions for uniform asymptotic equistability for input-free systems. This includes uniform and strong power equistability, and uniform and strong l p -equistability, among other technical conditions which also play essential role in stability theory. On other hand, it is shown that uniform asymptotic equistability for input-free systems is equivalent to each of the following concepts of uniform stability for forced systems: l p -input l p -state, c o -input c o -state, bounded-input bounded-state, l p>1 -input bounded-state, c sub (o)-input bounded-state, and convergent-input bounded-state; which are also equivalent to their nonuniform counterparts. For time-varying convergent systems, the above is also equivalent to convergent-input convergent-state stability. The proofs presented here are all ''elementary'' in the sense that they are based essentially only on the Banach-Steinhaus theorem. (autor) [pt

Non-verbal mother-child communication in conditions of maternal HIV in an experimental environment.

Science.gov (United States)

de Sousa Paiva, Simone; Galvão, Marli Teresinha Gimeniz; Pagliuca, Lorita Marlena Freitag; de Almeida, Paulo César

2010-01-01

Non-verbal communication is predominant in the mother-child relation. This study aimed to analyze non-verbal mother-child communication in conditions of maternal HIV. In an experimental environment, five HIV-positive mothers were evaluated during care delivery to their babies of up to six months old. Recordings of the care were analyzed by experts, observing aspects of non-verbal communication, such as: paralanguage, kinesics, distance, visual contact, tone of voice, maternal and infant tactile behavior. In total, 344 scenes were obtained. After statistical analysis, these permitted inferring that mothers use non-verbal communication to demonstrate their close attachment to their children and to perceive possible abnormalities. It is suggested that the mothers infection can be a determining factor for the formation of mothers strong attachment to their children after birth.

Does the Effect of Micro-Environmental Factors on a Street’s Appeal for Adults’ Bicycle Transport Vary across Different Macro-Environments? An Experimental Study

Science.gov (United States)

Mertens, Lieze; Van Cauwenberg, Jelle; Ghekiere, Ariane; Van Holle, Veerle; De Bourdeaudhuij, Ilse; Deforche, Benedicte; Nasar, Jack; Van de Weghe, Nico; Van Dyck, Delfien

2015-01-01

Background Characteristics of the physical environment can be classified into two broad categories: macro- (“raw” urban planning features influenced on a regional level) and micro- (features specifically within a streetscape influenced on a neighborhood level) environmental factors. In urban planning applications, it is more feasible to modify conditions at the neighborhood level than at the regional level. Yet for the promotion of bicycle transport we need to know whether relationships between micro-environmental factors and bicycle transport depend on different types of macro-environments. This study aimed to identify whether the effect of three micro-environmental factors (i.e., evenness of the cycle path surface, speed limits and type of separation between cycle path and motorized traffic) on the street’s appeal for adults’ bicycle transport varied across three different macro-environments (i.e., low, medium and high residential density street). Methods In total, 389 middle-aged adults completed a web-based questionnaire consisting of socio-demographic characteristics and a series of choice tasks with manipulated photographs, depicting two possible routes to cycle along. Conjoint analysis was used to analyze the data. Results Although the magnitude of the overall effects differed, in each macro-environment (i.e., low, medium and high residential density), middle-aged adults preferred a speed limit of 30 km/h, an even cycle path surface and a hedge as separation between motorized traffic and the cycle path compared to a speed limit of 50 or 70 km/h, a slightly uneven or uneven cycle path surface and a curb as separation or no separation between motorized traffic and the cycle path. Conclusions Our results suggest that irrespective of the macro-environment, the same micro-environmental factors are preferred in middle-aged adults concerning the street’s appeal for bicycle transport. The controlled environment simulations in the experimental choice task

Experimental study of elliptical jet from supercritical to subcritical conditions using planar laser induced fluorescence

Energy Technology Data Exchange (ETDEWEB)

Muthukumaran, C. K.; Vaidyanathan, Aravind, E-mail: aravind7@iist.ac.in [Department of Aerospace Engineering, Indian Institute of Space Science and Technology, Trivandrum, Kerala 695547 (India)

2015-03-15

The study of fluid jet dynamics at supercritical conditions involves strong coupling between fluid dynamic and thermodynamic phenomena. Beyond the critical point, the liquid-vapor coexistence ceases to exist, and the fluid exists as a single phase known as supercritical fluid with its properties that are entirely different from liquids and gases. At the critical point, the liquids do not possess surface tension and latent heat of evaporation. Around the critical point, the fluid undergoes large changes in density and possesses thermodynamic anomaly like enhancement in thermal conductivity and specific heat. In the present work, the transition of the supercritical and near-critical elliptical jet into subcritical as well as supercritical environment is investigated experimentally with nitrogen and helium as the surrounding environment. Under atmospheric condition, a liquid jet injected from the elliptical orifice exhibits axis switching phenomena. As the injection temperature increases, the axis switching length also increases. Beyond the critical temperature, the axis switching is not observed. The investigation also revealed that pressure plays a major role in determining the thermodynamic transition of the elliptical jet only for the case of supercritical jet injected into subcritical chamber conditions. At larger pressures, the supercritical jet undergoes disintegration and formation of droplets in the subcritical environment is observed. However, for supercritical jet injection into supercritical environment, the gas-gas like mixing behavior is observed.

Experimental study of elliptical jet from supercritical to subcritical conditions using planar laser induced fluorescence

International Nuclear Information System (INIS)

Muthukumaran, C. K.; Vaidyanathan, Aravind

2015-01-01

The study of fluid jet dynamics at supercritical conditions involves strong coupling between fluid dynamic and thermodynamic phenomena. Beyond the critical point, the liquid-vapor coexistence ceases to exist, and the fluid exists as a single phase known as supercritical fluid with its properties that are entirely different from liquids and gases. At the critical point, the liquids do not possess surface tension and latent heat of evaporation. Around the critical point, the fluid undergoes large changes in density and possesses thermodynamic anomaly like enhancement in thermal conductivity and specific heat. In the present work, the transition of the supercritical and near-critical elliptical jet into subcritical as well as supercritical environment is investigated experimentally with nitrogen and helium as the surrounding environment. Under atmospheric condition, a liquid jet injected from the elliptical orifice exhibits axis switching phenomena. As the injection temperature increases, the axis switching length also increases. Beyond the critical temperature, the axis switching is not observed. The investigation also revealed that pressure plays a major role in determining the thermodynamic transition of the elliptical jet only for the case of supercritical jet injected into subcritical chamber conditions. At larger pressures, the supercritical jet undergoes disintegration and formation of droplets in the subcritical environment is observed. However, for supercritical jet injection into supercritical environment, the gas-gas like mixing behavior is observed

Reconstruction of Oryza sativa indica Genome Scale Metabolic Model and Its Responses to Varying RuBisCO Activity, Light Intensity, and Enzymatic Cost Conditions

Directory of Open Access Journals (Sweden)

Ankita Chatterjee

2017-11-01

Full Text Available To combat decrease in rice productivity under different stresses, an understanding of rice metabolism is needed. Though there are different genome scale metabolic models (GSMs of Oryza sativa japonica, no GSM with gene-protein-reaction association exist for Oryza sativa indica. Here, we report a GSM, OSI1136 of O.s. indica, which includes 3602 genes and 1136 metabolic reactions and transporters distributed across the cytosol, mitochondrion, peroxisome, and chloroplast compartments. Flux balance analysis of the model showed that for varying RuBisCO activity (Vc/Vo (i the activity of the chloroplastic malate valve increases to transport reducing equivalents out of the chloroplast under increased photorespiratory conditions and (ii glyceraldehyde-3-phosphate dehydrogenase and phosphoglycerate kinase can act as source of cytosolic ATP under decreased photorespiration. Under increasing light conditions we observed metabolic flexibility, involving photorespiration, chloroplastic triose phosphate and the dicarboxylate transporters of the chloroplast and mitochondrion for redox and ATP exchanges across the intracellular compartments. Simulations under different enzymatic cost conditions revealed (i participation of peroxisomal glutathione-ascorbate cycle in photorespiratory H2O2 metabolism (ii different modes of the chloroplastic triose phosphate transporters and malate valve, and (iii two possible modes of chloroplastic Glu–Gln transporter which were related with the activity of chloroplastic and cytosolic isoforms of glutamine synthetase. Altogether, our results provide new insights into plant metabolism.

Influence of hydraulic regimes on bacterial community structure and composition in an experimental drinking water distribution system.

Science.gov (United States)

Douterelo, I; Sharpe, R L; Boxall, J B

2013-02-01

Microbial biofilms formed on the inner-pipe surfaces of drinking water distribution systems (DWDS) can alter drinking water quality, particularly if they are mechanically detached from the pipe wall to the bulk water, such as due to changes in hydraulic conditions. Results are presented here from applying 454 pyrosequencing of the 16S ribosomal RNA (rRNA) gene to investigate the influence of different hydrological regimes on bacterial community structure and to study the potential mobilisation of material from the pipe walls to the network using a full scale, temperature-controlled experimental pipeline facility accurately representative of live DWDS. Analysis of pyrosequencing and water physico-chemical data showed that habitat type (water vs. biofilm) and hydraulic conditions influenced bacterial community structure and composition in our experimental DWDS. Bacterial community composition clearly differed between biofilms and bulk water samples. Gammaproteobacteria and Betaproteobacteria were the most abundant phyla in biofilms while Alphaproteobacteria was predominant in bulk water samples. This suggests that bacteria inhabiting biofilms, predominantly species belonging to genera Pseudomonas, Zooglea and Janthinobacterium, have an enhanced ability to express extracellular polymeric substances to adhere to surfaces and to favour co-aggregation between cells than those found in the bulk water. Highest species richness and diversity were detected in 28 days old biofilms with this being accentuated at highly varied flow conditions. Flushing altered the pipe-wall bacterial community structure but did not completely remove bacteria from the pipe walls, particularly under highly varied flow conditions, suggesting that under these conditions more compact biofilms were generated. This research brings new knowledge regarding the influence of different hydraulic regimes on the composition and structure of bacterial communities within DWDS and the implication that this

Theoretical and experimental study of single particle tracking in extreme conditions: single photon imaging

International Nuclear Information System (INIS)

Cajgfinger, T.

2012-10-01

This manuscript presents my thesis on the high frame rate (500 frames / second) single-photon detector electron-bombarded CMOS (ebCMOS). The first section compares three ultra-sensitive detectors and their methods for improving photon sensitivity: the CMOS low noise (sCMOS), the electron-multiplying CCD (emCCD) with signal multiplication by pixel and the ebCMOS with amplification by applied electric field. The method developed to detect single photon impacts with intra-pixel resolution on the ebCMOS sensor is presented. The second section compares the localization accuracy of these detectors in extreme conditions of very low photon flux (<10 photons/frame). First the theoretical limit is calculated using the Cramer-Rao lower bound for significant parameter sets. An experimental comparison of the detectors is then described. The setup provides one or more point sources controlled in position, signal and background noise. The results allow a comparison of the experimental effectiveness, purity and localization accuracy. The last section describes two experiments with the ebCMOS camera. The first aims at tracking hundreds of quantum dots simultaneously at the Nanoptec center. The second focuses on the swimming of bacteria at the surface at the Joliot Curie Institute. The point sources tracking algorithm using single photons and the Kalman filter implementation developed for these experiments is also described. (author)

Understanding the behaviour of the actinides under disposal conditions: A comparison between calculated and experimental solubilities

International Nuclear Information System (INIS)

Pryke, D.C.; Rees, J.H.

1986-01-01

The solubilities of plutonium, americium and neptunium measured in simulated near-field waters have compared with those predicted using the simple thermodynamic model NearSol. The dependence of solubility on pH and redox potential is examined in an effort to understand the behaviour of actinides in disposal. The agreement was variable. Differences could be appreciable, in particular for neptunium under oxidizing conditions; conversly, the model successfully predicted the behaviour of neptunium under reducing conditions. Such comparisons pinpointed deficiences in the thermodynamic data base and showed the sensitivity of solubilities to certain experimental parameters such as Eh and the concentration of carbonate ions. A comparison between NearSol and the reaction pathway program PHREEQE gave generally good agreement. NearSol was quicker and easier to use, requiring only limited preselection of participating species; however it did not account for the behaviour of bulk inactive species in solution; like feature will be built into an updated version. (orig.)

Experimental study and phenomenological modeling of the hydrolysis of tritiated sodium: influence of experimental conditions on the tritium distribution in the effluents

International Nuclear Information System (INIS)

Chassery, Aurelien

2014-01-01

Within the framework of the decommissioning of fast reactors, several processes are under investigation regarding sodium disposal. One of them rests on the implementation of the sodium-water reaction (SWR), in a controlled and progressive way, to remove residual sodium containing impurities such as sodium hydrides, sodium oxides and tritiated sodium hydrides. Such a hydrolysis releases some amount of energy and produces a liquid effluent, composed of a solution of soda, and a gaseous effluent, composed of hydrogen, steam and an inert gas. The tritium, originally into the sodium as a soluble (T - ) or precipitate form (NaT), will be distributed between the liquid and gaseous effluent, and according to two chemical forms, the tritium hydride HT and the tritiated water HTO. HTO being 10,000 times more radio-toxic than HT, a precise knowledge of the mechanisms governing the distribution of tritium is necessary in order to estimate the exhaust gas releases and design the process needed to treat the off-gas before its release into the environment. An experimental study has been carried out in order to determine precisely the phenomena involved in the hydrolysis. The influence of the experimental conditions on the tritium distribution has been tested. The results of this study leaded to a phenomenological description of the tritiated sodium hydrolysis that will help to predict the composition of the effluents, regarding tritium. (author) [fr

Numerical simulation of diurnally varying thermal environment in a street canyon under haze-fog conditions

Science.gov (United States)

Tan, Zijing; Dong, Jingliang; Xiao, Yimin; Tu, Jiyuan

2015-10-01

The impact of haze-fog on surface temperature, flow pattern, pollutant dispersion and pedestrian thermal comfort are investigated using computational fluid dynamics (CFD) approach based on a three-dimensional street canyon model under different haze-fog conditions. In this study, light extinction coefficient (Kex) is adopted to represent haze-fog pollution level. Numerical simulations are performed for different Kex values at four representative time events (1000 LST, 1300 LST, 1600 LST and 2000 LST). The numerical results suggest that the surface temperature is strongly affected by the haze-fog condition. Surface heating induced by the solar radiation is enhanced by haze-fog, as higher surface temperature is observed under thicker haze-fog condition. Moreover, the temperature difference between sunlit and shadow surfaces is reduced, while that for the two shadow surfaces is slightly increased. Therefore, the surface temperature among street canyon facets becomes more evenly distributed under heavy haze-fog conditions. In addition, flow patterns are considerably altered by different haze-fog conditions, especially for the afternoon (1600 LST) case, in which thermal-driven flow has opposite direction as that of the wind-driven flow direction. Consequently, pollutants such as vehicular emissions will accumulate at pedestrian level, and pedestrian thermal comfort may lower under thicker haze-fog condition.

Modeling Quantum Dot Nanoparticle Fate and Transport in Saturated Porous Media under Varying Flow Conditions

Science.gov (United States)

Becker, M. D.; Wang, Y.; Englehart, J.; Pennell, K. D.; Abriola, L. M.

2010-12-01

As manufactured nanomaterials become more prevalent in commercial and industrial applications, the development of mathematical models capable of predicting nanomaterial transport and retention in subsurface systems is crucial to assessing their fate and distribution in the environment. A systematic modeling approach based on a modification of clean-bed filtration theory was undertaken to elucidate mechanisms governing the transport and deposition behavior of quantum dots in saturated quartz sand as a function of grain size and flow velocity. The traditional deposition governing equation, which assumes irreversible attachment by a first-order rate (katt), was modified to include a maximum or limiting retention capacity (Smax) and first-order detachment of particles from the solid phase (kdet). Quantum dot mobility experiments were performed in columns packed with three size fractions of Ottawa sand (d50 = 125, 165, and 335 μm) at two different pore-water velocities (0.8 m/d and 7.6 m/d). The CdSe quantum dots in a CdZnS shell and polyacrylic acid coating were negatively charged (zeta potential measured ca. -35 mV) with a hydrodynamic diameter of approximately 30 nm. Fitted values of katt, Smax, and kdet were obtained for each transport and deposition experiment through the implementation of a nonlinear least-squares routine developed to fit the model to experimental breakthrough and retention data via multivariate optimization. Fitted attachment rates and retention capacities increased exponentially with decreasing grain size at both flow rates, while no discernable trend was apparent for the fitted detachment rates. Maximum retention capacity values were plotted against a normalized mass flux expression, which accounts for flow conditions and grain size. A power function fit to the data yielded a dependence that was consistent with a previous study undertaken with fullerene nanoparticles.

Global exponential stability of fuzzy BAM neural networks with time-varying delays

International Nuclear Information System (INIS)

Zhang Qianhong; Luo Wei

2009-01-01

In this paper, a class of fuzzy bidirectional associated memory (BAM) neural networks with time-varying delays are studied. Employing fixed point theorem, matrix theory and inequality analysis, some sufficient conditions are established for the existence, uniqueness and global exponential stability of equilibrium point. The sufficient conditions are easy to verify at pattern recognition and automatic control. Finally, an example is given to show feasibility and effectiveness of our results.

Optimization of aspergillus niger nutritional conditions using statistical experimental methods for bio-recovery of manganese from pyrolusite

International Nuclear Information System (INIS)

Mujeeb-ur-Rahman; Yasinzai, M.M.; Tareen, R.B.; Iqbal, A.; Gul, S.; Odhano, E.A.

2011-01-01

Optimization of aspergillus niger nutritional conditions using statistical experimental methods for bio-recovery of manganese from pyrolusite Mujeeb-ur-rahman, Mohammed Masoom Yasinzai, Rasool Bakhsh Tareen, Asim Iqbal, Ejaz Ali Odhano, Shereen Gul. The nutritional requirements for Aspergillus niger PCSIR-06 for bio-recovery of manganese from pyrolusite ore were optimized. Box-Bhenken design and response surface methodology were used for designing of experiment and statistical analysis of the results. This procedure limited the number of actual experiments to 54 for studying the possible interaction between six nutrients. The optimum concentration of the nutrients were Sucrose 148.5 g/L, KH/sub 2/PO/sub 4/ 0.50 g/L, NH/sub 4/NO/sub 3/ 0.33 g/L, MgSO/sub 4/ 0.41 g/L, Zn 23.76 mg/L, Fe 0.18 mg/L for Aspergillus niger to achieve maximum bio-recovery of manganese (82.47 +- 5.67%). The verification run confirmed the predicted optimized concentration of all the six ingredients for maximum bio leaching of manganese and successfully confirmed the use of Box-Bhenken experimental design for maximum bio-recovery. Results also revealed that small and less time consuming experimental designs could be efficient for optimization of bio-recovery processes. (author)

Experimental simulations of oxidizing conditions and organic decomposition on the surface of Mars

International Nuclear Information System (INIS)

Stoker, C.R.; Mancinelli, R.L.; Mckay, C.P.

1988-01-01

One important scientific objective of a Mars Rover Sample Return mission would be to look for traces of living and extinct life on Mars. An instrument to search for organic carbon may be the simplest instrument that could screen samples which are interesting from a biological point of view. An experimental program is described which would help to understand the nature of the oxidizing soil on Mars and the mechanism responsible for organic degradation on the Martian surface. This is approached by lab simulations of the actual conditions that occur on Mars, particularly the oxidant production by atmospheric photochemistry, and the combined effects of UV light and oxidants in decomposing organic compounds. The results will be used to formulate models of the photochemistry of the atmospheric, the atmosphere-soil interaction, and the diffusion of reactive compounds into the soils. This information will provide insights and constraints on the design of a sampling strategy to search for organic compounds on Mars

Frequency-scanning interferometry using a time-varying Kalman filter for dynamic tracking measurements.

Science.gov (United States)

Jia, Xingyu; Liu, Zhigang; Tao, Long; Deng, Zhongwen

2017-10-16

Frequency scanning interferometry (FSI) with a single external cavity diode laser (ECDL) and time-invariant Kalman filtering is an effective technique for measuring the distance of a dynamic target. However, due to the hysteresis of the piezoelectric ceramic transducer (PZT) actuator in the ECDL, the optical frequency sweeps of the ECDL exhibit different behaviors, depending on whether the frequency is increasing or decreasing. Consequently, the model parameters of Kalman filter appear time varying in each iteration, which produces state estimation errors with time-invariant filtering. To address this, in this paper, a time-varying Kalman filter is proposed to model the instantaneous movement of a target relative to the different optical frequency tuning durations of the ECDL. The combination of the FSI method with the time-varying Kalman filter was theoretically analyzed, and the simulation and experimental results show the proposed method greatly improves the performance of dynamic FSI measurements.

Characterization of Transient Plasma Ignition Flame Kernel Growth for Varying Inlet Conditions

Science.gov (United States)

2009-12-01

from Intercity Manufacturing. Without their expertise in precision machining this thesis would not have been possible. Their countless hours spent...somewhere within the combustor due to the time required to produce the required conditions, and will be travelling at near Mach 5 speeds for most...atmospheric pressure. This sudden drop in pressure creates a rarefaction wave that travels forward in the combustor. The blowdown time for a 1 meter long

Exponential stability of fuzzy cellular neural networks with constant and time-varying delays

International Nuclear Information System (INIS)

Liu Yanqing; Tang Wansheng

2004-01-01

In this Letter, the global stability of delayed fuzzy cellular neural networks (FCNN) with either constant delays or time varying delays is proposed. Firstly, we give the existence and uniqueness of the equilibrium point by using the theory of topological degree and the properties of nonsingular M-matrix and the sufficient conditions for ascertaining the global exponential stability by constructing a suitable Lyapunov functional. Secondly, the criteria for guaranteeing the global exponential stability of FCNN with time varying delays are given and the estimation of exponential convergence rate with regard to speed of vary of delays is presented by constructing a suitable Lyapunov functional

Theoretical and experimental investigation of plasma and wave characteristics of coaxial discharges at low pressures

International Nuclear Information System (INIS)

Neichev, Z; Benova, E; Gamero, A; Sola, A

2006-01-01

The paper discusses a new configuration of the surface-wave sustained plasma - 'the coaxial structure'. The coaxial structure is investigated on the base of one-dimensional axial fluid model. That model is adequate enough for low pressure plasma, when the main process for charged particles production is the direct ionization from the ground state and the loss of electrons is due to diffusion to the wall. The role of the geometric factors is evaluated and discussed, varying the discharge conditions in the theoretical model. The main equations of the model - the local dispersion relation and the wave energy balance equation are obtained from Maxwell's equations with appropriate boundary conditions. The phase diagrams, the radial profiles of the electric field and the axial profiles of dimensionless electron number density, wave number, wave power are obtained at various plasma radii and dielectric tube thickness. The results are compared with those for the typical cylindrical plasma column at similar conditions. For the purpose of modelling at low pressure of a coaxial discharge sustained by a travelling electromagnetic wave, some important characteristics of the propagation of surface waves have been investigated experimentally. The axial profiles of the propagation coefficient and radial profiles of the electric field at different experimental conditions have been obtained and discussed

Creep and Environmental Durability of EBC/CMCs Under Imposed Thermal Gradient Conditions

Science.gov (United States)

Appleby, Matthew; Morscher, Gregory N.; Zhu, Dongming

2013-01-01

Interest in SiC fiber-reinforced SiC ceramic matrix composite (CMC) environmental barrier coating (EBC) systems for use in high temperature structural applications has prompted the need for characterization of material strength and creep performance under complex aerospace turbine engine environments. Stress-rupture tests have been performed on SiC/SiC composites systems, with varying fiber types and coating schemes to demonstrate material behavior under isothermal conditions. Further testing was conducted under exposure to thermal stress gradients to determine the effect on creep resistance and material durability. In order to understand the associated damage mechanisms, emphasis is placed on experimental techniques as well as implementation of non-destructive evaluation; including electrical resistivity monitoring. The influence of environmental and loading conditions on life-limiting material properties is shown.

Effects of varying laser trimming geometries on thin film\\ud resistors

OpenAIRE

Alafogianni, Maria; Birkett, Martin; Penlington, Roger

2017-01-01

Purpose - This paper studies the effects of varying laser trim patterns on several performance parameters of thin film resistors such as the temperature coefficient of resistance (TCR) and target resistance value.\\ud \\ud Design/methodology/approach - The benefits and limitations of basic trim patterns are taken into consideration and the plunge cut, double plunge cut and the curved L-cut were selected to be modelled and tested experimentally. A computer simulation of the laser trim patterns h...

Robust Stabilization of Discrete-Time Systems with Time-Varying Delay: An LMI Approach

Directory of Open Access Journals (Sweden)

Valter J. S. Leite

2008-01-01

Full Text Available Sufficient linear matrix inequality (LMI conditions to verify the robust stability and to design robust state feedback gains for the class of linear discrete-time systems with time-varying delay and polytopic uncertainties are presented. The conditions are obtained through parameter-dependent Lyapunov-Krasovskii functionals and use some extra variables, which yield less conservative LMI conditions. Both problems, robust stability analysis and robust synthesis, are formulated as convex problems where all system matrices can be affected by uncertainty. Some numerical examples are presented to illustrate the advantages of the proposed LMI conditions.

Ventilatory function assessment in safety pharmacology: Optimization of rodent studies using normocapnic or hypercapnic conditions

International Nuclear Information System (INIS)

Goineau, Sonia; Rompion, Sonia; Guillaume, Philippe; Picard, Sandra

2010-01-01

Although the whole body plethysmography for unrestrained animals is the most widely used method to assess the respiratory risk of new drugs in safety pharmacology, non-appropriate experimental conditions may mask deleterious side effects of some substances. If stimulant or bronchodilatory effects can be easily evidenced in rodents under standard experimental conditions, i.e. normal air breathing and diurnal phase, drug-induced respiratory depression remains more difficult to detect. This study was aimed at comparing the responsiveness of Wistar rats, Duncan Hartley guinea-pigs or BALB/c mice to the respiratory properties of theophylline (50 or 100 mg/kg p.o.) or morphine (30 mg/kg i.p.) under varying conditions (100% air versus 5% CO 2 -enriched air, light versus dark day phase), in order to select the most appropriate experimental conditions to each species for safety airway investigations. Our results showed that under normocapnia the ventilatory depressant effects of morphine can be easily evidenced in mice, slightly observed in guinea-pigs and not detected in rats in any day phase. Slight hypercapnic conditions enhanced the responsiveness of rats to morphine but not that of guinea-pigs and importantly they did not blunt the airway responsiveness of rats to the stimulation and bronchodilation evoked by theophylline, the most widely used reference agent in safety pharmacology studies. In conclusion, hypercapnic conditions associated with the non-invasive whole body plethysmography should be considered for optimizing the assessment of both the ventilatory depressant potential of morphine-like substances or the respiratory stimulant effects of new drugs in the rat, the most extensively used species in rodent safety and toxicological investigations.

Comparison of Experimental and Numerical Two-Phase Flows in a Porous Micro-Model

Directory of Open Access Journals (Sweden)

Dustin Crandall

2009-12-01

Full Text Available Characterizing two-phase flow in porous media is important to provide estimates of sweep efficiency in enhanced oil recovery and storage estimates in potential geological CO2 sequestration repositories. To further the current understanding of two-phase flow in porous media a micro-model of interconnected channels was designed and fabricated using stereolithography to experimentally study gas-liquid flows. This flowcell was created with a wide variability of throat dimensions to represent naturally occurring porous media. Low flow rate experiments of immiscible two-phase drainage were performed within this cell. Additionally, a computational model for analyzing two-phase flows in the same flowcell was developed and used to simulate conditions not possible with our laboratory settings. The computational model was first tested for the identical conditions used in the experimental studies, and was shown to be in good agreement with the experimentally determined fractal dimension of the invading gas structure, time until breakthrough, and fluid saturation. The numerical model was then used to study two-phase air-water flows in flowcells with the same geometry and different gas-liquid-solid contact angles. The percent saturation of air and the motion of the fluids through the cell were found to vary with changes in these parameters. Finally, to simulate flows expected during geologic carbon sequestration, the fluid properties and interface conditions were set to model the flow of CO2 into a brine-saturated porous medium at representative subsurface conditions. The CO2 flows were shown to have larger gas saturations than the previous air into water studies. Thus the accuracy of the computational model was supported by the flowcell experiments, and the computational model extended the laboratory results to conditions not possible with the apparatus used in the experiments.

Lyapunov Functions to Caputo Fractional Neural Networks with Time-Varying Delays

Directory of Open Access Journals (Sweden)

Ravi Agarwal

2018-05-01

Full Text Available One of the main properties of solutions of nonlinear Caputo fractional neural networks is stability and often the direct Lyapunov method is used to study stability properties (usually these Lyapunov functions do not depend on the time variable. In connection with the Lyapunov fractional method we present a brief overview of the most popular fractional order derivatives of Lyapunov functions among Caputo fractional delay differential equations. These derivatives are applied to various types of neural networks with variable coefficients and time-varying delays. We show that quadratic Lyapunov functions and their Caputo fractional derivatives are not applicable in some cases when one studies stability properties. Some sufficient conditions for stability of equilibrium of nonlinear Caputo fractional neural networks with time dependent transmission delays, time varying self-regulating parameters of all units and time varying functions of the connection between two neurons in the network are obtained. The cases of time varying Lipschitz coefficients as well as nonLipschitz activation functions are studied. We illustrate our theory on particular nonlinear Caputo fractional neural networks.

Development of a butterfly check valve model under natural circulation conditions

International Nuclear Information System (INIS)

Rao, Yuxian; Yu, Lei; Fu, Shengwei; Zhang, Fan

2015-01-01

Highlights: • Bases on Lim’s swing check valve model, a butterfly check valve model was developed. • The method to quantify the friction torque T F in Li’s model was corrected. • The developed model was implemented into the RELAP5 code and verified. - Abstract: A butterfly check valve is widely used to prevent a reverse flow in the pipe lines of a marine nuclear power plant. Under some conditions, the natural circulation conditions in particular, the fluid velocity through the butterfly check valve might become too low to hold the valve disk fully open, thereby the flow resistance of the butterfly check valve varies with the location of the valve disk and as a result the fluid flow is significantly affected by the dynamic motion of the valve disk. Simulation of a pipe line that includes some butterfly check valves, especially under natural circulation conditions, is thus complicated. This paper focuses on the development of a butterfly check valve model to enhance the capability of the thermal–hydraulic system code and the developed model is implemented into the RELAP5 code. Both steady-state calculations and transient calculations were carried out for the primary loop system of a marine nuclear power plant and the calculation results are compared with the experimental data for verification purpose. The simulation results show an agreement with the experimental data

Whole-Pin Furnace system: An experimental facility for studying irradiated fuel pin behavior under potential reactor accident conditions

International Nuclear Information System (INIS)

Liu, Y.Y.; Tsai, H.C.; Donahue, D.A.; Pushis, D.O.; Savoie, F.E.; Holland, J.W.; Wright, A.E.; August, C.; Bailey, J.L.; Patterson, D.R.

1990-05-01

The whole-pin furnace system is a new in-cell experimental facility constructed to investigate how irradiated fuel pins may fail under potential reactor accident conditions. Extensive checkouts have demonstrated excellent performance in remote operation, temperature control, pin breach detection, and fission gas handling. The system is currently being used in testing of EBIR-II-irradiated Integral Fast Reactor (IFR) metal fuel pins; future testing will include EBR-II-irradiated mixed-oxide fuel pins. 7 refs., 4 figs

Global exponential stability of uncertain fuzzy BAM neural networks with time-varying delays

International Nuclear Information System (INIS)

Syed Ali, M.; Balasubramaniam, P.

2009-01-01

In this paper, the Takagi-Sugeno (TS) fuzzy model representation is extended to the stability analysis for uncertain Bidirectional Associative Memory (BAM) neural networks with time-varying delays using linear matrix inequality (LMI) theory. A novel LMI-based stability criterion is obtained by LMI optimization algorithms to guarantee the exponential stability of uncertain BAM neural networks with time-varying delays which are represented by TS fuzzy models. Finally, the proposed stability conditions are demonstrated with numerical examples.

An Investigation about using Nanorefrigerants in Air Conditioning Systems According to the Theoretical, CFD and Experimental Review of the Recent Literature

Directory of Open Access Journals (Sweden)

Farshad Panahizadeh

2016-10-01

Full Text Available Greenhouse gases (GHG causing global warming and climate change. In the year 2014, 32.3 billion tones CO2 emitted to the atmosphere as the most important greenhouse gas. According to the statistics, a significant portion of this amount is related to electricity demand of air conditioning systems, for producing a one ton of refrigeration in HVAC air cooled or water cooled systems respectively 1026 and 764 grams GHG emitted in the atmosphere. Therefore, air conditioning systems have an important role in the global warming and climate change. By increasing the COP of air conditioning systems the electricity demand of them reduced. One strategy for increasing the COP of air conditioning systems is using nanorefrigerants. In the present study, a comprehensive information is given regarding to use nanorefrigerants in air conditioning systems according to the theoretical, CFD and experimental review of the recent literature. This paper gives assistance to designers of air conditioning systems in their future efforts for selecting refrigerant for their systems

Radionuclide release from spent fuel under geologic disposal conditions: An overview of experimental and theoretical work through 1985

Energy Technology Data Exchange (ETDEWEB)

Reimus, P.W.; Simonson, S.A.

1988-04-01

This report presents an overview of experimental and theoretical work on radionuclide release from spent fuel and uranium dioxide (UO/sub 2/) under geologic disposal conditions. The purpose of the report is to provide a source book of information that can be used to develop models that describe radionuclide release from spent fuel waste packages. Modeling activities of this nature will be conducted within the Waste Package Program (WPP) of the Department of Energy's Salt Repository Project (SRP). The topics discussed include experimental methods for investigating radionuclide release, how results have been reported from radionuclide release experiments, theoretical studies of UO/sub 2/ and actinide solubility, results of experimental studies of radionuclide release from spent fuel and UO/sub 2/ (i.e., the effects of different variables on radionuclide release), characteristics of spent fuel pertinent to radionuclide release, and status of modeling of radionuclide release from spent fuel. Appendix A presents tables of data from spent fuel radionuclide release experiments. These data have been digitized from graphs that appear in the literature. An annotated bibliography of literature on spent fuel characterization is provided in Appendix B.

Experimental and modeling study of hydrogen/syngas production and particulate emissions from a natural gas-fueled partial oxidation engine

International Nuclear Information System (INIS)

McMillian, Michael H.; Lawson, Seth A.

2006-01-01

In this study, a combustion model was first applied to conditions representing varying compression ratios and equivalence ratios to investigate engine exhaust composition from partial oxidation (POX) of natural gas in reciprocating engines. The model was experimentally validated over a range of equivalence ratios from 1.3 to 1.6 with a spark-ignited single cylinder engine fueled by natural gas. The modeling results matched well with engine gaseous emission data over the experimental range. The model was also extended to higher equivalence ratios to predict H 2 and CO production at engine conditions and stoichiometries representative of homogeneous charge compression ignition (HCCI) engine operation. Secondly, over the same experimental range of equivalence ratios, particulate samples were taken to determine both total particulate mass production (g/hph) via gravimetric measurement as well as particle size distribution and loading via a scanning mobility particle sizer (SMPS). While experiments indicate hydrogen yields up to 11% using spark ignition (SI), modeling results indicate that greater than 20% H 2 yield may be possible in HCCI operation. Over the experimental range, rich-burn particulate matter (PM) production is no greater than that from typical lean-burn operation. Finally, an energy balance was performed over the range of engine experimental operation. (author)

Measurement of the redistribution of arsenic at nickel silicide/silicon interface by secondary ion mass spectrometry: artifact and optimized analysis conditions

International Nuclear Information System (INIS)

Hoummada, K.; Mangelinck, D.; Perrin, C.; Carron, V.; Holliger, P.

2008-01-01

The arsenic redistribution after NiSi formation has been measured by secondary ion mass spectrometry (SIMS). The NiSi film has been obtained by solid state reaction of a Ni thin film with a silicon substrate doped with As. An increase in the As SIMS signal at the NiSi/Si interface was observed for some experimental conditions. By varying the SIMS experimental parameters (incidence angle and the impact energy), the As signal at NiSi/Si interface was found to change. The SIMS experimental parameters have been optimized and were found to be an impact energy of 1 keV and an incidence angle superior to 50 deg. This allows us to minimize differences in sputtering rate and ion yield between NiSi and Si and to obtain a good depth resolution and dynamic range. Under these conditions the bump in the As signal does not appear: this illustrates the difficulty to measure concentration at interface by SIMS

Performance investigation of low – Concentration photovoltaic systems under hot and arid conditions: Experimental and numerical results

International Nuclear Information System (INIS)

Yousef, Mohamed S.; Abdel Rahman, Ali K.; Ookawara, S.

2016-01-01

Highlights: • Influence of cooling on the performance of photovoltaic systems. • A comprehensive model (optical, thermal, and electrical) was developed. • Experimental measurements were conducted under hot climate conditions. • For conventional photovoltaic with cooling, about 11% more power was obtained. • For concentrated photovoltaic with cooling, about 15% more power was obtained. - Abstract: In this study, a comparative performance analysis was performed between a conventional photovoltaic system and a low-concentration photovoltaic system. Two typical photovoltaic modules and two compound parabolic concentrating photovoltaic systems were examined. A Cooling system was employed to lower the temperature of the solar cells in each of the two configurations. Experimental and numerical investigations of the performance of the two arrangements with and without cooling were presented. Experiments were conducted outdoors at the Egypt-Japan University of Science and Technology, subjected to the hot climate conditions of New Borg El-Arab City, Alexandria, Egypt (Longitude/Latitude: E 029°42′/N 30°55′). A comprehensive system model was established, which comprises an optical model, coupled with thermal and electrical models. The coupled model was developed analytically and solved numerically, using MATLAB software, to assess the overall performance of the two configurations, considering the concentration ratio of the concentrated photovoltaic system to be 2.4X. The results indicated that cooling the solar panels considerably improved the electrical power yield of the photovoltaic systems. By employing cooling, the temperatures of the conventional photovoltaic system and the concentrated photovoltaic system were effectively lowered by approximately 25% and 30%, respectively, resulting in a significant enhancement in the electrical power output of the photovoltaic system by 11% and that of the concentrated photovoltaic system by 15%. Furthermore, the

Experimental Incubations Elicit Profound Changes in Community Transcription in OMZ Bacterioplankton

Science.gov (United States)

Stewart, Frank J.; Dalsgaard, Tage; Young, Curtis R.; Thamdrup, Bo; Revsbech, Niels Peter; Ulloa, Osvaldo; Canfield, Don E.; DeLong, Edward F.

2012-01-01

Sequencing of microbial community RNA (metatranscriptome) is a useful approach for assessing gene expression in microorganisms from the natural environment. This method has revealed transcriptional patterns in situ, but can also be used to detect transcriptional cascades in microcosms following experimental perturbation. Unambiguously identifying differential transcription between control and experimental treatments requires constraining effects that are simply due to sampling and bottle enclosure. These effects remain largely uncharacterized for “challenging” microbial samples, such as those from anoxic regions that require special handling to maintain in situ conditions. Here, we demonstrate substantial changes in microbial transcription induced by sample collection and incubation in experimental bioreactors. Microbial communities were sampled from the water column of a marine oxygen minimum zone by a pump system that introduced minimal oxygen contamination and subsequently incubated in bioreactors under near in situ oxygen and temperature conditions. Relative to the source water, experimental samples became dominated by transcripts suggestive of cell stress, including chaperone, protease, and RNA degradation genes from diverse taxa, with strong representation from SAR11-like alphaproteobacteria. In tandem, transcripts matching facultative anaerobic gammaproteobacteria of the Alteromonadales (e.g., Colwellia) increased 4–13 fold up to 43% of coding transcripts, and encoded a diverse gene set suggestive of protein synthesis and cell growth. We interpret these patterns as taxon-specific responses to combined environmental changes in the bioreactors, including shifts in substrate or oxygen availability, and minor temperature and pressure changes during sampling with the pump system. Whether such changes confound analysis of transcriptional patterns may vary based on the design of the experiment, the taxonomic composition of the source community, and on the

Modelling conditional correlations of asset returns: A smooth transition approach

DEFF Research Database (Denmark)

Silvennoinen, Annastiina; Teräsvirta, Timo

In this paper we propose a new multivariate GARCH model with time-varying conditional correlation structure. The time-varying conditional correlations change smoothly between two extreme states of constant correlations according to a predetermined or exogenous transition variable. An LM-test is d......In this paper we propose a new multivariate GARCH model with time-varying conditional correlation structure. The time-varying conditional correlations change smoothly between two extreme states of constant correlations according to a predetermined or exogenous transition variable. An LM......-test is derived to test the constancy of correlations and LM- and Wald tests to test the hypothesis of partially constant correlations. Analytical expressions for the test statistics and the required derivatives are provided to make computations feasible. An empirical example based on daily return series of ve...

CADMIUM EXCRETION IN FECES OF RATS AT EXPERIMENTAL CONDITIONS

Directory of Open Access Journals (Sweden)

O. A. Zemlianyi

2014-10-01

Full Text Available Studies demonstrated that the excretions per 1 gof rat weight inthe experimental group usually prevails over the  control group, especially in the second part of the experiment. The increase in the amount of feces in animals of the experimental group was also registered. Such processes may indicate the intense excretory processes and  increase the output of harmful  pollutants from the rats  together with overall stimulation of rat digestive activity. The higher correlations between Cd and other pollutants, namely toxic Ni and Pb (r = 0.84 and 0.91, respectively were calculated for rat feces of experimental group compared to the control. The concentration of Cd and Pb in the excretion of experimental group was maximal in the first day of the experiment, suggesting definite reaction towards rapid output of maximum amount of toxicants from rat body. Subsequently, a decrease in concentration of other pollutants demonstrated their incorporation in metabolic processes and significant accumulation in rat body (kidney and liver, or involvement of other mechanisms for neutralization and removal of intoxicants. Given the increasing amount of excretions  in the second half of the experiment, this may be a solution to this issue. The Cd output per 1 g of rat weight was maximal in the first day, followed by a rapid decline and partial restoration in second half of the experiment. Obviously, it confirms the theory of substitution mechanisms in excretion of significant amount of hazardous toxicants and shifting towards less concentrated excretions in greater amount. Thus, the correlation index between the percentage of excreted pollutant and its concentration in the excretion was 0.75. When we considered only the first 7 days this increased to 0.91 and proved that during the first stage of experiment the percentage of pollutants excretion was dependent upon its concentration in feces. Correlation between Cd output rate and excretion volumes was

Wall conditioning for ITER: Current experimental and modeling activities

Energy Technology Data Exchange (ETDEWEB)

Douai, D., E-mail: david.douai@cea.fr [CEA, IRFM, Association Euratom-CEA, 13108 St. Paul lez Durance (France); Kogut, D. [CEA, IRFM, Association Euratom-CEA, 13108 St. Paul lez Durance (France); Wauters, T. [LPP-ERM/KMS, Association Belgian State, 1000 Brussels (Belgium); Brezinsek, S. [FZJ, Institut für Energie- und Klimaforschung Plasmaphysik, 52441 Jülich (Germany); Hagelaar, G.J.M. [Laboratoire Plasma et Conversion d’Energie, UMR5213, Toulouse (France); Hong, S.H. [National Fusion Research Institute, Daejeon 305-806 (Korea, Republic of); Lomas, P.J. [CCFE, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Lyssoivan, A. [LPP-ERM/KMS, Association Belgian State, 1000 Brussels (Belgium); Nunes, I. [Associação EURATOM-IST, Instituto de Plasmas e Fusão Nuclear, 1049-001 Lisboa (Portugal); Pitts, R.A. [ITER International Organization, F-13067 St. Paul lez Durance (France); Rohde, V. [Max-Planck-Institut für Plasmaphysik, 85748 Garching (Germany); Vries, P.C. de [ITER International Organization, F-13067 St. Paul lez Durance (France)

2015-08-15

Wall conditioning will be required in ITER to control fuel and impurity recycling, as well as tritium (T) inventory. Analysis of conditioning cycle on the JET, with its ITER-Like Wall is presented, evidencing reduced need for wall cleaning in ITER compared to JET–CFC. Using a novel 2D multi-fluid model, current density during Glow Discharge Conditioning (GDC) on the in-vessel plasma-facing components (PFC) of ITER is predicted to approach the simple expectation of total anode current divided by wall surface area. Baking of the divertor to 350 °C should desorb the majority of the co-deposited T. ITER foresees the use of low temperature plasma based techniques compatible with the permanent toroidal magnetic field, such as Ion (ICWC) or Electron Cyclotron Wall Conditioning (ECWC), for tritium removal between ITER plasma pulses. Extrapolation of JET ICWC results to ITER indicates removal comparable to estimated T-retention in nominal ITER D:T shots, whereas GDC may be unattractive for that purpose.

Measurement of instantaneous rotational speed using double-sine-varying-density fringe pattern

Science.gov (United States)

Zhong, Jianfeng; Zhong, Shuncong; Zhang, Qiukun; Peng, Zhike

2018-03-01

Fast and accurate rotational speed measurement is required both for condition monitoring and faults diagnose of rotating machineries. A vision- and fringe pattern-based rotational speed measurement system was proposed to measure the instantaneous rotational speed (IRS) with high accuracy and reliability. A special double-sine-varying-density fringe pattern (DSVD-FP) was designed and pasted around the shaft surface completely and worked as primary angular sensor. The rotational angle could be correctly obtained from the left and right fringe period densities (FPDs) of the DSVD-FP image sequence recorded by a high-speed camera. The instantaneous angular speed (IAS) between two adjacent frames could be calculated from the real-time rotational angle curves, thus, the IRS also could be obtained accurately and efficiently. Both the measurement principle and system design of the novel method have been presented. The influence factors on the sensing characteristics and measurement accuracy of the novel system, including the spectral centrobaric correction method (SCCM) on the FPD calculation, the noise sources introduce by the image sensor, the exposure time and the vibration of the shaft, were investigated through simulations and experiments. The sampling rate of the high speed camera could be up to 5000 Hz, thus, the measurement becomes very fast and the change in rotational speed was sensed within 0.2 ms. The experimental results for different IRS measurements and characterization of the response property of a servo motor demonstrated the high accuracy and fast measurement of the proposed technique, making it attractive for condition monitoring and faults diagnosis of rotating machineries.

Estudo experimental da aplicação retiniana do laser infravermelho via transescleral sob condições de baixa visibilidade Transscleral infrared laser retinal photocoagulation experimental study under low visibility conditions

Directory of Open Access Journals (Sweden)

Dario Grechi Goulart

2008-06-01

Full Text Available OBJETIVOS: Pesquisa experimental, com laser de diodo infravermelho, para estimar a segurança, a reprodutibilidade e a permeabilidade da parede ocular à sua atuação clínica, quando aplicado via transescleral, em condições de baixa visibilidade. MÉTODOS: Submetemos olhos de coelhos pigmentados da raça Nova Zelândia à fotocoagulação retiniana por laser de diodo infravermelho. No olho direito, realizamos fotocoagulação via transescleral sob parâmetros de potência e tempo pré-determinados clinicamente. No olho esquerdo, foram repetidos os mesmos valores da potência e tempo usados no olho direito, desta vez, via transpupilar. Imediatamente e após 2 meses, estudos clínicos baseados na retinografia e histopatológicos foram realizados. RESULTADOS: A permeabilidade da parede ocular, quando da aplicação do laser de diodo infravermelho via transescleral, variou entre 58,95 e 63,87%. A média da permeabilidade da parede ocular a 300 mW (63,14% mostrou-se significativamente superior àquela da permeabilidade da parede ocular encontrada a 500 mW (59,11%, (PPURPOSE: Retinal photocoagulation under poor visualization condition is often required. Transscleral infrared laser can be used as an alternative to regular transpupillary treatment. Based upon retinographic measurements, we proposed to estimate the reproducibility as well as ocular wall permeability rate for this treatment. Our primary goal was to evaluate whether this technique can deliver adequate photocoagulation at predetermined parameters without direct retinal visualization. METHODS: In New Zealand pigmented rabbits, optimal transscleral infrared diode laser settings were administered to the right eye. With the same parameters, transpupillary photocoagulation was repeated in the left eye. Retinographic and clinical examinations were performed immediately and two months later. RESULTS: Ocular wall permeability rate varied between 58.95 and 63.87%. Average permeability using a

Experimental Study on the Burning Behavior of Pool Fires in Rooms with Different Wall Linings

DEFF Research Database (Denmark)

Poulsen, Annemarie; Jomaas, Grunde

2011-01-01

An experimental test series, comprising 10 experiments with varying pool sizes, lining materials and amounts of liquid burning, was conducted under free burn and room burn conditions. The thermal feedback from the enclosure (ISO 9705 Room Corner Test facility) enhanced the burning rate of the poo...... in the shortest time. Given the profound difference between the enclosure tests and the free burn tests and also between enclosure tests with different linings, it is recommended to show great caution if free burn tests are to be used in design fire scenarios....

An Experimental Insight into Extracellular Phosphatases – Differential Induction of Cell-Specific Activity in Green Algae Cultured under Various Phosphorus Conditions

Directory of Open Access Journals (Sweden)

Jaroslav Vrba

2018-02-01

Full Text Available Extracellular phosphatase activity (PA has been used as an overall indicator of P depletion in lake phytoplankton. However, detailed insights into the mechanisms of PA regulation are still limited, especially in the case of acid phosphatases. The novel substrate ELF97 phosphate allows for tagging PA on single cells in an epifluorescence microscope. This fluorescence-labeled enzyme activity (FLEA assay enables for autecological studies in natural phytoplankton and algal cultures. We combined the FLEA assay with image analysis to measure cell-specific acid PA in two closely related species of the genus Coccomyxa (Trebouxiophyceae, Chlorophyta isolated from two acidic lakes with distinct P availability. The strains were cultured in a mineral medium supplied with organic (beta-glycerol phosphate or inorganic (orthophosphate P at three concentrations. Both strains responded to experimental conditions in a similar way, suggesting that acid extracellular phosphatases were regulated irrespectively of the origin and history of the strains. We found an increase in cell-specific PA at low P concentration and the cultures grown with organic P produced significantly higher (ca. 10-fold PA than those cultured with the same concentrations of inorganic P. The cell-specific PA measured in the cultures grown with the lowest organic P concentration roughly corresponded to those of the original Coccomyxa population from an acidic lake with impaired P availability. The ability of Coccomyxa strains to produce extracellular phosphatases, together with tolerance for both low pH and metals can be one of the factors enabling the dominance of the genus in extreme conditions of acidic lakes. The analysis of frequency distribution of the single-cell PA documented that simple visual counting of ‘active’ (labeled and ‘non-active’ (non-labeled cells can lead to biased conclusions regarding algal P status because the actual PA of the ‘active’ cells can vary from

Determination of service lives under varying loading using a life-fraction rule. Pt. 1

International Nuclear Information System (INIS)

Schaefer, L.

1986-01-01

Previously the attempt has been made to improve the often accuracy of the life-fraction rule (Robinson), applied to calculate the service lives under varying loading, by introducing constants into the mathematical representation of the rule which take into account the influence of the material and the conditions of loading. Therefore, the calculated service lives are not real predictions. In this work description based on constants is dispensed with and only one boundary condition is indicated for the life-fraction rule which is necessary and sufficient to calculate correctly any fractional damage and hence any service life under varying loading. The abbreviated wording of this boundary condition is: To calculate a fractional damage, the life fraction tsub(i) must be devided by a service life tsub(m,i), the structural condition Gsub(i) being the same. The specimen (X10NiCrTi1616 steel) will rupture as soon as the sum of fractional damages has attained unity: Σsub(i)(tsub(i)/tsub(m,i)) sub(Gsub(i)) = 1. (orig./GSCH)

Critical velocities in He II for independently varied superfluid and normal fluid velocities

International Nuclear Information System (INIS)

Baehr, M.L.

1984-01-01

Experiments were performed to measure the critical velocity in pure superflow and compare to the theoretical prediction; to measure the first critical velocity for independently varied superfluid and normal fluid velocities; and to investigate the propagation of the second critical velocity from the thermal counterflow line through the V/sub n/,-V/sub s/ quadrant. The experimental apparatus employed a thermal counterflow heater to adjust the normal fluid velocity, a fountain pump to vary the superfluid velocity, and a level sensing capacitor to measure the superfluid velocity. The results of the pure superfluid critical velocity measurements indicate that this velocity is temperature independent contrary to Schwarz's theory. It was found that the first critical velocity for independently varied V/sub n/ and V/sub s/ could be described by a linear function of V/sub n/ and was otherwise temperature independent. It was found that the second critical velocity could only be distinguished near the thermal counterflow line

Finite-time stability of neutral-type neural networks with random time-varying delays

Science.gov (United States)

Ali, M. Syed; Saravanan, S.; Zhu, Quanxin

2017-11-01

This paper is devoted to the finite-time stability analysis of neutral-type neural networks with random time-varying delays. The randomly time-varying delays are characterised by Bernoulli stochastic variable. This result can be extended to analysis and design for neutral-type neural networks with random time-varying delays. On the basis of this paper, we constructed suitable Lyapunov-Krasovskii functional together and established a set of sufficient linear matrix inequalities approach to guarantee the finite-time stability of the system concerned. By employing the Jensen's inequality, free-weighting matrix method and Wirtinger's double integral inequality, the proposed conditions are derived and two numerical examples are addressed for the effectiveness of the developed techniques.

Basic regulatory principles of Escherichia coli's electron transport chain for varying oxygen conditions

NARCIS (Netherlands)

Henkel, S.G.; Ter Beek, A.S.; Steinsiek, S.; Stagge, S.; Bettenbrock, K.; Teixeira De Mattos, M.J.; Sauter, T.; Sawodny, O.; Ederer, M.

2014-01-01

For adaptation between anaerobic, micro-aerobic and aerobic conditions Escherichia coli's metabolism and in particular its electron transport chain (ETC) is highly regulated. Although it is known that the global transcriptional regulators FNR and ArcA are involved in oxygen response it is unclear

Premixed Flames Under Microgravity and Normal Gravity Conditions

Science.gov (United States)

Krikunova, Anastasia I.; Son, Eduard E.

2018-03-01

Premixed conical CH4-air flames were studied experimentally and numerically under normal straight, reversed gravity conditions and microgravity. Low-gravity experiments were performed in Drop tower. Classical Bunsen-type burner was used to find out features of gravity influence on the combustion processes. Mixture equivalence ratio was varied from 0.8 to 1.3. Wide range of flow velocity allows to study both laminar and weakly turbulized flames. High-speed flame chemoluminescence video-recording was used as diagnostic. The investigations were performed at atmospheric pressure. As results normalized flame height, laminar flame speed were measured, also features of flame instabilities were shown. Low- and high-frequency flame-instabilities (oscillations) have a various nature as velocity fluctuations, preferential diffusion instability, hydrodynamic and Rayleigh-Taylor ones etc., that was explored and demonstrated.

Cooling the vertical surface by conditionally single pulses

Directory of Open Access Journals (Sweden)

Karpov Pavel

2017-01-01

Full Text Available You Sprays with periodic supply of the droplet phase have great opportunities to control the heat exchange processes. Varying pulse duration and frequency of their repetition, we can achieve the optimal conditions of evaporative cooling with minimization of the liquid flow rate. The paper presents experimental data on studying local heat transfer on a large subcooled surface, obtained on the original setup with multinozzle controlled system of impact irrigation by the gas-droplet flow. A contribution to intensification of the spray parameters (flow rate, pulse duration, repetition frequency per a growth of integral heat transfer was studied. Data on instantaneous distribution of the heat flux value helped us to describe the processes occurring on the studied surface. These data could describe the regime of “island” film cooling.

Large-scale experimental facility for emergency condition investigation of a new generation NPP WWER-640 reactor with passive safety systems

Energy Technology Data Exchange (ETDEWEB)

Aniskevich, Y.N.; Vasilenko, V.A.; Zasukha, V.K.; Migrov, Y.A.; Khabensky, V.B. [Research Inst. of Technology NITI (Russian Federation)

1997-12-31

The creation of the large-scale integral experimental facility (KMS) is specified by the programme of the experimental investigations to justify the engineering decisions on the safety of the design of the new generation NPP with the reactor WWER-640. The construction of KMS in a full volume will allow to conduct experimental investigations of all physical phenomena and processes, practically, occurring during the accidents on the NPPs with the reactor of WWER type and including the heat - mass exchange processes with low rates of the coolant, which is typical during the utilization of the passive safety systems, process during the accidents with a large leak, and also the complex intercommunicated processes in the reactor unit, passive safety systems and in the containment with the condition of long-term heat removal to the final absorber. KMS is being constructed at the Research Institute of Technology (NITI), Sosnovy Bor, Leningrad region, Russia. (orig.). 5 refs.

Large-scale experimental facility for emergency condition investigation of a new generation NPP WWER-640 reactor with passive safety systems

International Nuclear Information System (INIS)

Aniskevich, Y.N.; Vasilenko, V.A.; Zasukha, V.K.; Migrov, Y.A.; Khabensky, V.B.

1997-01-01

The creation of the large-scale integral experimental facility (KMS) is specified by the programme of the experimental investigations to justify the engineering decisions on the safety of the design of the new generation NPP with the reactor WWER-640. The construction of KMS in a full volume will allow to conduct experimental investigations of all physical phenomena and processes, practically, occurring during the accidents on the NPPs with the reactor of WWER type and including the heat - mass exchange processes with low rates of the coolant, which is typical during the utilization of the passive safety systems, process during the accidents with a large leak, and also the complex intercommunicated processes in the reactor unit, passive safety systems and in the containment with the condition of long-term heat removal to the final absorber. KMS is being constructed at the Research Institute of Technology (NITI), Sosnovy Bor, Leningrad region, Russia. (orig.)

Large-scale experimental facility for emergency condition investigation of a new generation NPP WWER-640 reactor with passive safety systems

Energy Technology Data Exchange (ETDEWEB)

Aniskevich, Y N; Vasilenko, V A; Zasukha, V K; Migrov, Y A; Khabensky, V B [Research Inst. of Technology NITI (Russian Federation)

1998-12-31

The creation of the large-scale integral experimental facility (KMS) is specified by the programme of the experimental investigations to justify the engineering decisions on the safety of the design of the new generation NPP with the reactor WWER-640. The construction of KMS in a full volume will allow to conduct experimental investigations of all physical phenomena and processes, practically, occurring during the accidents on the NPPs with the reactor of WWER type and including the heat - mass exchange processes with low rates of the coolant, which is typical during the utilization of the passive safety systems, process during the accidents with a large leak, and also the complex intercommunicated processes in the reactor unit, passive safety systems and in the containment with the condition of long-term heat removal to the final absorber. KMS is being constructed at the Research Institute of Technology (NITI), Sosnovy Bor, Leningrad region, Russia. (orig.). 5 refs.

Psychoimmunomodulating activity of Phenibut under conditions of experimental hyperthyroidism

Directory of Open Access Journals (Sweden)

M A Samotrueva

2012-03-01

Full Text Available Psychoimmunomodulating action of Phenibut has been shown on the model of experimental hyperthyroidism. It has been found that the drug (intra-abdominal injection in the dose 25 mg/kg is able to restore humoral immunoreactivity and liquidate disturbances of the behaviour reactions appearing in the result of induced pathology as well.

Experimental investigation of hydrocarbon mixtures to replace HFC-134a in an automotive air conditioning system

International Nuclear Information System (INIS)

Wongwises, Somchai; Kamboon, Amnouy; Orachon, Banchob

2006-01-01

This paper presents an experimental study on the application of hydrocarbon mixtures to replace HFC-134a in automotive air conditioners. The hydrocarbons investigated are propane (R290), butane (R600) and isobutane (R600a). The measured data are obtained from an automotive air conditioning test facility utilizing HFC-134a as the refrigerant. The air conditioner, with a capacity of 3.5 kW driven by a Diesel engine, is charged and tested with four different ratios of hydrocarbon mixtures. The experiments are conducted at the same surrounding conditions. The temperature and pressure of the refrigerant at every major position in the refrigerant loop, the temperature, flow rate and humidity of air, torque and engine speed are recorded and analyzed. The parameters investigated are the refrigeration capacity, the compressor power and the coefficient of performance (COP). The results show that propane/butane/isobutane: 50%/40%/10% is the most appropriate alternative refrigerant to replace HFC-134a, having the best performance of all the hydrocarbon mixtures investigated

The effects of transient conditions on the onset of intermittent dryout during blowdown

Energy Technology Data Exchange (ETDEWEB)

Statham, B.A., E-mail: stathaba@mcmaster.ca; Novog, D.R., E-mail: novog@mcmaster.ca

2017-06-15

Highlights: • This papers presents the results of an experimental investigation of transient critical heat flux in high quality and intermediate pressure water. • In existing literature conclusions vary from those showing no effect of transient conditions to results which show 30–40% improvement in CHF. • Along with new CHF data points in the liquid film dominated flow regime, the authors provide a methodology for producing bias free estimates of CHF based on existing correlations. • With these bias free CHF estimates, comparisons are made between transient and steady-state CHF at comparable local conditions. • The work concludes that based on consistently collected and analyzed data that quasi-steady CHF experiments adequately predict transient CHF using the same local thermalhydraulic conditions. - Abstract: For a given set of conditions in a boiling system the point of liquid film dryout or departure from nucleate boiling corresponds to the change from convective or nucleate boiling to transition or film boiling. This change is associated with a rapid deterioration of the heat transfer coefficient and the heat flux at this transition is denoted the critical heat flux (CHF). Computer models used to predict station transients and CHF rely heavily on empirical correlations to predict the CHF. Liquid film CHF data are usually obtained using a quasi-steady method wherein the heat flux is incremented in small steps with each step being allowed to reach a new equilibrium until an abnormal temperature increase is detected on the experimental surfaces. In applying a correlation derived from steady-state experiments to transient analyses these codes implicitly assume that dryout will occur for the same local conditions during transients as during steady state conditions. There is some disagreement in literature as to the validity of this hypothesis. This paper provides new steady-state and transient experimental data for CHF in water at intermediate pressures

Fast space-varying convolution using matrix source coding with applications to camera stray light reduction.

Science.gov (United States)

Wei, Jianing; Bouman, Charles A; Allebach, Jan P

2014-05-01

Many imaging applications require the implementation of space-varying convolution for accurate restoration and reconstruction of images. Here, we use the term space-varying convolution to refer to linear operators whose impulse response has slow spatial variation. In addition, these space-varying convolution operators are often dense, so direct implementation of the convolution operator is typically computationally impractical. One such example is the problem of stray light reduction in digital cameras, which requires the implementation of a dense space-varying deconvolution operator. However, other inverse problems, such as iterative tomographic reconstruction, can also depend on the implementation of dense space-varying convolution. While space-invariant convolution can be efficiently implemented with the fast Fourier transform, this approach does not work for space-varying operators. So direct convolution is often the only option for implementing space-varying convolution. In this paper, we develop a general approach to the efficient implementation of space-varying convolution, and demonstrate its use in the application of stray light reduction. Our approach, which we call matrix source coding, is based on lossy source coding of the dense space-varying convolution matrix. Importantly, by coding the transformation matrix, we not only reduce the memory required to store it; we also dramatically reduce the computation required to implement matrix-vector products. Our algorithm is able to reduce computation by approximately factoring the dense space-varying convolution operator into a product of sparse transforms. Experimental results show that our method can dramatically reduce the computation required for stray light reduction while maintaining high accuracy.

Time-varying value of electric energy efficiency

Energy Technology Data Exchange (ETDEWEB)

Mims, Natalie A.; Eckman, Tom; Goldman, Charles

2017-06-30

in value of all the components of avoided costs across the locations studied. -Of the five energy efficiency measures studied, those targeting residential air conditioning in summer-peaking electric systems have the most significant added value when the total time-varying value is considered. -The increased use of rooftop solar systems, storage, and demand response, and the addition of electric vehicles and other major new electricity-consuming end uses are anticipated to significantly alter the load shape of many utility systems in the future. Data used to estimate the impact of energy efficiency measures on electric system peak demands will need to be updated periodically to accurately reflect the value of savings as system load shapes change. -Publicly available components of electric system costs avoided through energy efficiency are not uniform across states and utilities. Inclusion or exclusion of these components and differences in their value affect estimates of the time-varying value of energy efficiency. -Publicly available data on end-use load and energy savings shapes are limited, are concentrated regionally, and should be expanded.

Sterilization efficacy of ultraviolet irradiation on microbial aerosols under dynamic airflow by experimental air conditioning systems

International Nuclear Information System (INIS)

Nakamura, Hiroshi

1987-01-01

In order to know the sterilization efficacy of ultraviolet irradiation on microbial aerosols, the size and the weight of the aerosol particles were evaluated, and these were irradiated under dynamic air flow created by an experimental air conditioning system. The experimental apparatus consisted of a high efficiency particulate air (HEPA) filter, an aerosol generator, spiral UV lamps placed around a quart glass tube, an Andersen air sampler and a vacuum pump. They were connected serially by stainless steel ducts (85 mm in diameter, 8 m in length). Six types of microbial aerosols generated from an ultrasonic nebulizer were irradiated by UV rays (wavelength 254 nm, mean density 9400 μW/cm 2 ). Their irradiation time ranged from 1.0 to 0.0625 seconds. The microbial aerosols were collected onto the trypticase soy agar (TSA) medium in the Andersen air sampler. After incubation, the number of colony forming units (CFU) were counted, and converted to particle counts. The diameter of microbial aerosol particles calculated by their log normal distribution were found to match the diameter of a single bacteria cell measured by a microscope. The sterilization efficacy of UV in standard airflow conditions (0.5 sec. irradiation) were found to be over 99.5 % in Staphylococcus aureus, Staphylococcus epidermidis, Serratia marcescens, Bacillus subtilis (vegetative cell) and Bacillus subtilis (spore) and 67 % in Aspergillus niger (conidium). In A. niger, which was the most resistant microbe to UV irradiation, the efficacy rose up to 79 % when irradiated for 1.0 sec., and it was observed that the growth speed of the colonies was slower than that of the controls. It was thought that UV rays caused some damage to the proliferation of A. niger cells. (author)

The performance of cleaner wrasse, Labroides dimidiatus, in a reversal learning task varies across experimental paradigms

Directory of Open Access Journals (Sweden)

Simon Gingins

2018-05-01

Full Text Available Testing performance in controlled laboratory experiments is a powerful tool for understanding the extent and evolution of cognitive abilities in non-human animals. However, cognitive testing is prone to a number of potential biases, which, if unnoticed or unaccounted for, may affect the conclusions drawn. We examined whether slight modifications to the experimental procedure and apparatus used in a spatial task and reversal learning task affected performance outcomes in the bluestreak cleaner wrasse, Labroides dimidiatus (hereafter “cleaners”. Using two-alternative forced-choice tests, fish had to learn to associate a food reward with a side (left or right in their holding aquarium. Individuals were tested in one of four experimental treatments that differed slightly in procedure and/or physical set-up. Cleaners from all four treatment groups were equally able to solve the initial spatial task. However, groups differed in their ability to solve the reversal learning task: no individuals solved the reversal task when tested in small tanks with a transparent partition separating the two options, whereas over 50% of individuals solved the task when performed in a larger tank, or with an opaque partition. These results clearly show that seemingly insignificant details to the experimental set-up matter when testing performance in a spatial task and might significantly influence the outcome of experiments. These results echo previous calls for researchers to exercise caution when designing methodologies for cognition tasks to avoid misinterpretations.

The performance of cleaner wrasse, Labroides dimidiatus, in a reversal learning task varies across experimental paradigms.

Science.gov (United States)

Gingins, Simon; Marcadier, Fanny; Wismer, Sharon; Krattinger, Océane; Quattrini, Fausto; Bshary, Redouan; Binning, Sandra A

2018-01-01

Testing performance in controlled laboratory experiments is a powerful tool for understanding the extent and evolution of cognitive abilities in non-human animals. However, cognitive testing is prone to a number of potential biases, which, if unnoticed or unaccounted for, may affect the conclusions drawn. We examined whether slight modifications to the experimental procedure and apparatus used in a spatial task and reversal learning task affected performance outcomes in the bluestreak cleaner wrasse, Labroides dimidiatus (hereafter "cleaners"). Using two-alternative forced-choice tests, fish had to learn to associate a food reward with a side (left or right) in their holding aquarium. Individuals were tested in one of four experimental treatments that differed slightly in procedure and/or physical set-up. Cleaners from all four treatment groups were equally able to solve the initial spatial task. However, groups differed in their ability to solve the reversal learning task: no individuals solved the reversal task when tested in small tanks with a transparent partition separating the two options, whereas over 50% of individuals solved the task when performed in a larger tank, or with an opaque partition. These results clearly show that seemingly insignificant details to the experimental set-up matter when testing performance in a spatial task and might significantly influence the outcome of experiments. These results echo previous calls for researchers to exercise caution when designing methodologies for cognition tasks to avoid misinterpretations.

Frequency variations of gravity waves interacting with a time-varying tide

Energy Technology Data Exchange (ETDEWEB)

Huang, C.M.; Zhang, S.D.; Yi, F.; Huang, K.M.; Gan, Q.; Gong, Y. [Wuhan Univ., Hubei (China). School of Electronic Information; Ministry of Education, Wuhan, Hubei (China). Key Lab. of Geospace Environment and Geodesy; State Observatory for Atmospheric Remote Sensing, Wuhan, Hubei (China); Zhang, Y.H. [Nanjing Univ. of Information Science and Technology (China). College of Hydrometeorolgy

2013-11-01

Using a nonlinear, 2-D time-dependent numerical model, we simulate the propagation of gravity waves (GWs) in a time-varying tide. Our simulations show that when aGW packet propagates in a time-varying tidal-wind environment, not only its intrinsic frequency but also its ground-based frequency would change significantly. The tidal horizontal-wind acceleration dominates the GW frequency variation. Positive (negative) accelerations induce frequency increases (decreases) with time. More interestingly, tidal-wind acceleration near the critical layers always causes the GW frequency to increase, which may partially explain the observations that high-frequency GW components are more dominant in the middle and upper atmosphere than in the lower atmosphere. The combination of the increased ground-based frequency of propagating GWs in a time-varying tidal-wind field and the transient nature of the critical layer induced by a time-varying tidal zonal wind creates favorable conditions for GWs to penetrate their originally expected critical layers. Consequently, GWs have an impact on the background atmosphere at much higher altitudes than expected, which indicates that the dynamical effects of tidal-GW interactions are more complicated than usually taken into account by GW parameterizations in global models.

Statistical approach for uncertainty quantification of experimental modal model parameters

DEFF Research Database (Denmark)

Luczak, M.; Peeters, B.; Kahsin, M.

2014-01-01

Composite materials are widely used in manufacture of aerospace and wind energy structural components. These load carrying structures are subjected to dynamic time-varying loading conditions. Robust structural dynamics identification procedure impose tight constraints on the quality of modal models...... represent different complexity levels ranging from coupon, through sub-component up to fully assembled aerospace and wind energy structural components made of composite materials. The proposed method is demonstrated on two application cases of a small and large wind turbine blade........ This paper aims at a systematic approach for uncertainty quantification of the parameters of the modal models estimated from experimentally obtained data. Statistical analysis of modal parameters is implemented to derive an assessment of the entire modal model uncertainty measure. Investigated structures...

Asymmetric vibrations of shells of revolution having meridionally varying curvature and thickness

International Nuclear Information System (INIS)

Suzuki, Katsuyoshi; Kosawada, Tadashi; Miura, Kazuyuki.

1988-01-01

An exact method using power series expansions is presented for solving asymmetric free vibration problems for shells of revolution having meridionally varying curvature and thickness. The gaverning equations of motion and the boundary conditions are derived from the stationary conditions of the Lagrangian of the shells of revolution. The method is demonstrated for shells of revolution having elliptical, cycloidal, parabolical, catenary and hyperbolical meridional curvature. The natural frequencies are numerically calculated for these shells having second degree thickness variation. (author)

Robust stability analysis of uncertain stochastic neural networks with interval time-varying delay

International Nuclear Information System (INIS)

Feng Wei; Yang, Simon X.; Fu Wei; Wu Haixia

2009-01-01

This paper addresses the stability analysis problem for uncertain stochastic neural networks with interval time-varying delays. The parameter uncertainties are assumed to be norm bounded, and the delay factor is assumed to be time-varying and belong to a given interval, which means that the lower and upper bounds of interval time-varying delays are available. A sufficient condition is derived such that for all admissible uncertainties, the considered neural network is robustly, globally, asymptotically stable in the mean square. Some stability criteria are formulated by means of the feasibility of a linear matrix inequality (LMI), which can be effectively solved by some standard numerical packages. Finally, numerical examples are provided to demonstrate the usefulness of the proposed criteria.

The flux pinning properties of BaSnO{sub 3}-added GdBa{sub 2}Cu3O{sub 7-δ} films with varying growth conditions

Energy Technology Data Exchange (ETDEWEB)

Lee, J. K.; Oh, J. Y.; Kang, B. [Dept. of Physics, Chungbuk National University, Cheongju (Korea, Republic of); Lee, J. M.; Kang, W. N. [Dept. of Physics, Sungkyunkwan University, Suwon (Korea, Republic of)

2017-09-15

Addition of BaSnO{sub 3} (BSO) to GdBa{sub 2}Cu{sub 3}O{sub 7-δ} (GdBCO) is reported to enhance the flux pinning property of GdBCO thick films. To investigate the effect of growth condition on the pinning properties, 700 nm-thick BSO-added GdBCO films deposited with varying temperatures and growth rates were prepared by using a pulsed laser deposition method. As the deposition temperature increases, the critical current density and the pinning force density show an improved field dependence up to 750 ℃ due to the increase in the formation of the a-axis growth and the BSO nanostructures. The films deposited at higher temperatures show degraded surfaces and as a result, degraded pinning behaviors. For the change in growth rate, the critical current density and the pinning force increase as the repetition rate increase at low magnetic fields, but this behavior is reversed in high magnetic fields. These results indicate that the film growth conditions significantly affect the formation of BSO nanostructures and the pinning properties of BSO-added GdBCO films.

Physiological response of invasive mussel Limnoperna fortunei (Dunker, 1857 (Bivalvia: Mytilidae submitted to transport and experimental conditions

Directory of Open Access Journals (Sweden)

N. I. S. Cordeiro

Full Text Available Abstract Successful animal rearing under laboratory conditions for commercial processes or laboratory experiments is a complex chain that includes several stressors (e.g., sampling and transport and incurs, as a consequence, the reduction of natural animal conditions, economic losses and inconsistent and unreliable biological results. Since the invasion of the bivalve Limnoperna fortunei (Dunker, 1857 in South America, several studies have been performed to help control and manage this fouling pest in industrial plants that use raw water. Relatively little attention has been given to the laboratory rearing procedure of L. fortunei, its condition when exposed to a stressor or its acclimation into laboratory conditions. Considering this issue, the aims of this study are to (i investigate L. fortunei physiological responses when submitted to the depuration process and subsequent air transport (without water/dry condition at two temperatures, based on glycogen concentrations, and (ii monitor the glycogen concentrations in different groups when maintained for 28 days under laboratory conditions. Based on the obtained results, depuration did not affect either of the groups when they were submitted to approximately eight hours of transport. The variation in glycogen concentration among the specimens that were obtained from the field under depurated and non-depurated conditions was significant only in the first week of laboratory growth for the non-depurated group and in the second week for the depurated group. In addition, the tested temperature did not affect either of the groups that were submitted to transport. The glycogen concentrations were similar to those of the specimens that were obtained from the field in third week, which suggests that the specimens acclimated to laboratory conditions during this period of time. Thus, the results indicate that the air transport and acclimation time can be successfully incorporated into experimental studies

Mobility of Iron-Cyanide Complexes in a Humic Topsoil under Varying Redox Conditions

Directory of Open Access Journals (Sweden)

Thilo Rennert

2009-01-01

Full Text Available The potentially toxic Fe-CN complexes ferricyanide, [FeIII(CN6]3−, and ferrocyanide, [FeII(CN6]4−, undergo a variety of redox processes in soil, which affect their mobility. We carried out microcosm experiments with suspensions of a humic topsoil (pH 5.3; Corg 107 g kg-1 to which we added ferricyanide (20 mg l-1. We varied the redox potential (EH from −280 to 580 mV by using O2, N2 and glucose. The decrease of EH led to decreasing concentrations of Fe-CN complexes and partial reductive dissolution of (hydrous Fe and Mn oxides. The dynamics of aqueous Fe-CN concentrations was characterized by decreasing concentrations when the pH rose and the EH dropped. We attribute these dependencies to adsorption on organic surfaces, for which such a pH/EH behavior has been shown previously. Adsorption was reversible, because when the pH and EH changed into the opposite direction, desorption occurred. This study demonstrates the possible impact of soil organic matter on the fate of Fe-CN complexes in soil.

Structural nested mean models for assessing time-varying effect moderation.