The influence of the vane on the lubrication characteristics between the vane and the rolling piston of a rotary compressor

International Nuclear Information System (INIS)

Cho, Ihn Sung; Jung, Jae Youn

2006-01-01

The rolling piston type rotary compressor has been widely used for refrigeration and air -conditioning systems due to its compactness and high-speed operation. The present analysis is part of a research program directed toward maximizing the advantages of refrigerant compressors. The study of lubrication characteristics in the critical sliding component is essential for the design of refrigerant compressors. Therefore, theoretical investigation of the lubrication characteristics of a rotary compressor being used for refrigeration and air-conditioning systems was investigated. The Newton-Raphson method was used for a partial elastohydrodynamic lubrication analysis between the vane and the rolling piston of a rotary compressor. The results demonstrated that the vane thickness and the center line position of the vane significantly influenced the friction force and the energy loss between the vane and the rolling piston

Experimental hot-wire measurements in a centrifugal compressor with vaned diffuser

International Nuclear Information System (INIS)

Pinarbasi, Ali

2008-01-01

The purpose of this study was to improve the understanding of the flow physics in a centrifugal compressor with vaned diffuser. For this reason three component hot wire measurements in the vaneless space and vane region of a low speed centrifugal compressor are presented. A low speed compressor with a 19 bladed backswept impeller and diffuser with 16 wedge vanes were used. The measurements were made at three inter-vane positions and are presented as mean velocity, turbulent kinetic energy and flow angle distributions. The flow entering the diffuser closely resembles the classic jet-wake flow characteristic of centrifugal impeller discharges. A strong upstream influence of the diffuser vanes is observed which results in significant variations in flow quantities between the vane-to-vane locations. The circumferential variations due to the passage and blade wakes rapidly mix out in the vaneless space, although some variations are still discernible in the vaned region. The impeller blade wakes mix out rapidly within the vaneless space and more rapidly than in an equivalent vaneless diffuser. Although the flow is highly non uniform in velocity at the impeller exit, there is no evidence in the results of any separation from the diffuser vanes

Extended residence time centrifugal contactor design modification and centrifugal contactor vane plate valving apparatus for extending mixing zone residence time

Science.gov (United States)

Wardle, Kent E.

2017-06-06

The present invention provides an annular centrifugal contactor, having a housing adapted to receive a plurality of flowing liquids; a rotor on the interior of the housing; an annular mixing zone, wherein the annular mixing zone has a plurality of fluid retention reservoirs with ingress apertures near the bottom of the annular mixing zone and egress apertures located above the ingress apertures of the annular mixing zone; and an adjustable vane plate stem, wherein the stem can be raised to restrict the flow of a liquid into the rotor or lowered to increase the flow of the liquid into the rotor.

Numerical Analysis and Geometry Optimisation of Vertical Vane of Room Air-conditioner

Directory of Open Access Journals (Sweden)

Al-Obaidi Abdulkareem Sh. Mahdi

2018-01-01

Full Text Available Vertical vanes of room air-conditioners are used to control and direct cold air. This paper aims to study vertical vane as one of the parameters that affect the efficiency of dissipating cold air to a given space. The vertical vane geometry is analysed and optimised for lower production cost using CFD. The optimised geometry of the vertical vane should have the same or increased efficiency of dissipating cold air and have lesser mass compared to the existing original design. The existing original design of vertical vane is simplified and analysed by using ANSYS Fluent. Efficiency of wind direction is define as how accurate the direction of airflow coming out from vertical vane. In order to calculate the efficiency of wind direction, 15° and 30° rotation of vertical vane inside room air-conditioner are simulated. The efficiency of wind direction for 15° rotation of vertical vane is 57.81% while efficiency of wind direction for 30° rotation of vertical vane is 47.54%. The results of the efficiency of wind direction are used as base reference for parametric study. The parameters investigated for optimisation of vertical vane are focused at length of long span, tip chord and short span. The design of 15% decreased in vane surface area at tip chord is the best optimised design of vertical vane because the efficiency of wind direction is the highest as 60.32%.

Solar energy system with wind vane

Science.gov (United States)

Grip, Robert E

2015-11-03

A solar energy system including a pedestal defining a longitudinal axis, a frame that is supported by the pedestal and that is rotateable relative to the pedestal about the longitudinal axis, the frame including at least one solar device, and a wind vane operatively connected to the frame to urge the frame relative to the pedestal about the longitudinal axis in response to wind acting on the wind vane.

Study and Control of a Radial Vaned Diffuser Stall

Directory of Open Access Journals (Sweden)

Aurélien Marsan

2012-01-01

Full Text Available The aim of the present study is to evaluate the efficiency of a boundary layer suction technique in case of a centrifugal compressor stage in order to extend its stable operating range. First, an analysis of the flow pattern within the radial vaned diffuser is presented. It highlights the stall of the diffuser vanes when reaching a low massflow. A boundary layer separation in the hub-suction side corner grows when decreasing the massflow from the nominal operating point to the surge and finally leads to a massive stall. An aspiration strategy is investigated in order to control the stall. The suction slot is put in the vicinity of the saddle that originates the main separating skin-friction line, identified thanks to the analysis of the skin-friction pattern. Several aspiration massflow rates are tested, and two different modelings of the aspiration are evaluated. Finally, an efficient control is reached with a removal of only 0,1% of the global massflow and leads—from a steady-state calculations point of view—to an increase by 40% of the compressor operating range extent.

Study of the laboratory Vane test on mortars

Energy Technology Data Exchange (ETDEWEB)

Bauer, Elton [Post-Graduate Program in Structures and Civil Construction, Civil and Environmental Engineering Department, University of Brasilia Campus Universitario Darcy Ribeiro Asa Norte, 70910-900 Brasilia/DF (Brazil); Sousa, Jose G.G. de [Federal University of Vale do Sao Francisco, Av. Presidente Tancredo Neve, 100-56306-410 Petroline/PE (Brazil); Guimaraes, Elvio A. [University of Feira de Santana, Campus Universitario-BR 116, Km 03-44031-460-Feira de Santana/BA (Brazil); Silva, Francisco Gabriel S. [Post-Graduate Program in Structures and Civil Construction, University of Brasilia Campus Universitario Darcy Ribeiro Asa Norte, 70910-900 Brasilia/DF (Brazil)

2007-01-15

The Vane method (Vane test) is a simple but efficient method to measure the yield stress among other properties of non-Newtonian fluids. These fluids exhibit big flow effects in flat surfaces which are common in rheometers devices of different types (parallel disk or coaxial cylinder types). The yield stress values obtained with Vane method, in pastes, gels, soils and concentrated suspensions, have presented good agreement with results found elsewhere by most of the rheologic methods shown in the literature. The aim of this work is presenting a discussion on the capabilities of the Vane method, highlighting the theoretical basis, the functioning principle with some operational particularities, and some applications of the method in investigating the properties of fresh rendering mortars. Works of several authors that used the same method for fresh mortars were reviewed and experimental results of tests done by the authors of this paper using the method are also presented and discussed, focusing on the desirable workability for mortars. The Vane test method is an important tool in studying rheological properties in freshly applied mortar. It is able to define clear conditions in the applying of this material. (author)

Optimization analysis of a new vane MRF damper

Energy Technology Data Exchange (ETDEWEB)

Zhang, J Q; Feng, Z Z; Jing, Q [Department of Technical Support Engineering, Academy of Armored Force Engineering, Beijing, 100072 (China)], E-mail: zhangjq63@yahoo.com.cn

2009-02-01

The primary purpose of this study was to provide the optimization analysis certain characteristics and benefits of a vane MRF damper. Based on the structure of conventional vane hydraulic damper for heavy vehicle, a narrow arc gap between clapboard and rotary vane axle, which one rotates relative to the other, was designed for MRF valve and the mathematical model of damping was deduced. Subsequently, the finite element analysis of electromagnetic circuit was done by ANSYS to perform the optimization process. Some ways were presented to augment the damping adjustable multiple under the condition of keeping initial damping forces and to increase fluid dwell time through the magnetic field. The results show that the method is useful in the design of MR dampers and the damping adjustable range of vane MRF damper can meet the requirement of heavy vehicle semi-active suspension system.

Turbocharger with variable nozzle having vane sealing surfaces

Science.gov (United States)

Arnold, Philippe [Hennecourt, FR; Petitjean, Dominique [Julienrupt, FR; Ruquart, Anthony [Thaon les Vosges, FR; Dupont, Guillaume [Thaon les Vosges, FR; Jeckel, Denis [Thaon les Vosges, FR

2011-11-15

A variable nozzle for a turbocharger includes a plurality of vanes rotatably mounted on a nozzle ring and disposed in a nozzle flow path defined between the nozzle ring and an opposite nozzle wall. Either or both of the faces of the nozzle ring and nozzle wall include(s) at least one step that defines sealing surfaces positioned to be substantially abutted by airfoil surfaces of the vanes in the closed position of the vanes and to be spaced from the airfoil surfaces in positions other than the closed position. This substantial abutment between the airfoil surfaces and the sealing surfaces serves to substantially prevent exhaust gas from leaking past the ends of the airfoil portions. At the same time, clearances between the nozzle ring face and the end faces of the airfoil portions can be sufficiently large to prevent binding of the vanes under all operating conditions.

Demonstration and Field Evaluation of Streambank Stabilization with Submerged Vanes

Science.gov (United States)

Whitman, H.; Hoopes, J.; Poggi, D.; Fitzpatrick, F.; Walz, K.; ,

2001-01-01

The effectiveness of submerged vanes for reducing bank erosion and improving aquatic habitat is being evaluated at a site on North Fish Creek, a Lake Superior tributary. Increased runoff from agricultural areas with clayey soils has increased flood magnitudes and the erosion potential/transport capacity of the stream. Most of the creek's sediment load originates from the erosion of 17 large bluffs. This creek contains important recreational fisheries that are potentially limited by the loss of aquatic habitat from deposition of sediment on spawning beds. Submerged vanes are a cost effective and environmentally less intrusive alternative to traditional structural stabilization measures. Submerged vanes protrude from a channel bed, are oriented at an angle to the local velocity, and are distributed along a portion of channel. They induce a transverse force and torque on the flow along with longitudinal vortexes that alter the cross sectional shape and alignment of the channel. Submerged vanes were installed at a bluff/bend site in summer and fall 2000. The number, size, and layout of the vanes were based upon the channel morphology under estimated bankfull conditions. The effectiveness of the vanes will be evaluated by comparing surveys of the bluff face, streamflow, and channel conditions for several years after installation of the submerged vanes with surveys before and immediately after their installation.

Suppression of tonal noise in a centrifugal fan using guide vanes

Science.gov (United States)

Paramasivam, Kishokanna; Rajoo, Srithar; Romagnoli, Alessandro

2015-11-01

This paper presents the work aiming for tonal noise reduction in a centrifugal fan. In previous studies, it is well documented that tonal noise is the dominant noise source generated in centrifugal fans. Tonal noise is generated due to the aerodynamic interaction between the rotating impeller and stationary diffuser vanes. The generation of tonal noise is related to the pressure fluctuation at the leading edge of the stationary vane. The tonal noise is periodic in time which occurs at the blade passing frequency (BPF) and its harmonics. Much of previous studies, have shown that the stationary vane causes the tonal noise and generation of non-rotational turbulent noise. However, omitting stationary vanes will lead to the increase of non-rotational turbulent noise resulted from the high velocity of the flow leaving the impeller. Hence in order to reduce the tonal noise and the non-rotational noise, guide vanes were designed as part of this study to replace the diffuser vanes, which were originally used in the chosen centrifugal fan. The leading edge of the guide vane is tapered. This modification reduces the strength of pressure fluctuation resulting from the interaction between the impeller outflow and stationary vane. The sound pressure level at blade passing frequency (BPF) is reduced by 6.8 dB, the 2nd BPF is reduced by 4.1 dB and the 3rd BPF reduced by about 17.5 dB. The overall reduction was 0.9 dB. The centrifugal fan with tapered guide vanes radiates lower tonal noise compared to the existing diffuser vanes. These reductions are achieved without compromising the performance of the centrifugal fan. The behavior of the fluid flow was studied using computational fluid dynamics (CFD) tools and the acoustics characteristics were determined through experiments in an anechoic chamber.

Study on Orbital Liquid Transport and Interface Behavior in Vane Tank

Science.gov (United States)

Kang, Qi; Rui, Wei

2016-07-01

Liquid propellant tank is used to supply gas free liquid for spacecraft as an important part of propulsion system. The liquid behavior dominated by surface tension in microgravity is obviously different with that on the ground, which put forward a new challenge to the liquid transport and relocation. The experiments which are investigated at drop tower in National Microgravity Lab have concentrated on liquid relocation following thruster firing. Considered that the liquid located at the bottom in the direction of the acceleration vector, a sphere scale vane tank is used to study the liquid-gas interface behaviors with different acceleration vector and different filling independently and we obtain a series of stable equilibrium interface and relocation time. We find that there is an obvious sedimentation in the direction of acceleration vector when fill rate greater than 2% fill. Suggestions have been put forward that outer vanes transferring liquid to the outlet should be fixed and small holes should be dogged at the vane close to the center post to improve the liquid flow between different vanes when B0 is greater than 2.5. The research about liquid transport alone ribbon vanes is simulated though software Flow3D. The simulation process is verified by comparing the liquid lip and vapor-liquid interface obtained from drop tower experiment and simulation result when fill rate is 15%. Then the influence of fill rate, numbers of vanes and the gap between vane and wall is studied through the same simulate process. Vanes' configurations are also changed to study the effect on the lip and liquid volume below some section. Some suggestions are put forward for the design of vanes.

Bed erosion control at 60 degree river confluence using vanes

Science.gov (United States)

Wuppukondur, Ananth; Chandra, Venu

2017-04-01

Confluences are common occurrences along natural rivers. Hydrodynamics at the confluence is complex due to merging of main and lateral flows with different characteristics. Bed erosion occurs at the confluence due to turbulence and also secondary circulation induced by centrifugal action of the lateral flow. The eroded sediment poses various problems in the river ecosystem including river bank failure. Reservoirs are majorly affected due to sediment deposition which reduces storage capacity. The bed erosion also endangers stability of pipeline crossings and bridge piers. The aim of this experimental study is to check the performance of vanes in controlling bed erosion at the confluence. Experiments are performed in a 600 confluence mobile bed model with a non-uniform sediment of mean particle size d50 = 0.28mm. Discharge ratio (q=ratio of lateral flow discharge to main flow discharge) is maintained as 0.5 and 0.75 with a constant average main flow depth (h) of 5cm. Vanes of width 0.3h (1.5cm) and thickness of 1 mm are placed along the mixing layer at an angle of 150, 300 and 600(with respect to main flow) to perform the experiments. Also, two different spacing of 2h and 3h (10cm and 15cm) between the vanes are used for conducting the experiments. A digital point gauge with an accuracy of ±0.1mm is used to measure bed levels and flow depths at the confluence. An Acoustic Doppler Velocitimeter (ADV) with a frequency of 25Hz and accuracy of ±1mm/s is used to measure flow velocities. Maximum scour depth ratio Rmax, which is ratio between maximum scour depth (Ds) and flow depth (h), is used to present the experimental results.From the experiments without vanes, it is observed that the velocities are increasing along the mixing layer and Rmax=0.82 and 1.06, for q=0.5 and 0.75, respectively. The velocities reduce with vanes since roughness increases along the mixing layer. For q=0.5 and 0.75, Rmax reduces to 0.62 and 0.7 with vanes at 2h spacing, respectively. Similarly

Hot spot detection system for vanes or blades of a combustion turbine

Science.gov (United States)

Twerdochlib, M.

1999-02-02

This invention includes a detection system that can determine if a turbine component, such as a turbine vane or blade, has exceeded a critical temperature, such as a melting point, along any point along the entire surface of the vane or blade. This system can be employed in a conventional combustion turbine having a compressor, a combustor and a turbine section. Included within this system is a chemical coating disposed along the entire interior surface of a vane or blade and a closed loop cooling system that circulates a coolant through the interior of the vane or blade. If the temperature of the vane or blade exceeds a critical temperature, the chemical coating will be expelled from the vane or blade into the coolant. Since while traversing the closed loop cooling system the coolant passes through a detector, the presence of the chemical coating in the coolant will be sensed by the system. If the chemical coating is detected, this indicates that the vane or blade has exceeded a critical temperature. 5 figs.

Powerful Swirl Generation of Flow-driven Rotating Mixing Vane for Enhancing CHF

International Nuclear Information System (INIS)

Seo, Han; Seo, Seok Bin; Heo, Hyo; Bang, In Cheol

2014-01-01

Mixing vanes are utilized to improve CHF and heat transfer performance in the rod bundle during normal operation. Experimental measurement of the swirling flow from a split vane pair was conducted using particle image velocimetry (PIV) and boroscope. The lateral velocity fields show that the swirling flow was initially centered in the subchannel and the computational fluid dynamics (CFD) analysis was performed based on the experiment. To visualize flow patterns in the 5Χ5 subchannel using PIV, matching the refraction between the working fluid and the structure was considered and the experiment aimed to develop the experimental data for providing fundamental information of the CFD analysis. The fixed split vane is the main mixing inducer in the fuel assembly. In a heat exchanger research, propeller type swirl generates at several pitch ratios and different blades angles were used to enhance heat transfer rate. Significant improvements of the heat transfer rate using the propellers were confirmed due to creation of tangential flow. In the present study, the mixing effect of rotation vane which has a shape of propeller was studied using PIV. A split vane was considered in the experiment to show the effect of rotation vane. Vertical and horizontal flow analyses were conducted to show the possible use of rotation vane in a subchannel. In the present work, the study of flow visualization using three types of vanes is conducted to show the mixing effect. The vertical flow and the horizontal flow distributions were analyzed in the two experimental facilities. For the vertical flow facility, flow distributions, flow profiles, and the turbulence kinetic energy are analyzed at the centerline of the channel. The results show that the rotation vane has the highest flow and turbulence kinetic intensity at the centerline of the channel. For the horizontal flow facility, the results indicate that lateral flow of the rotation vane is generated and maintained along with the flow

An analytical model for droplet separation in vane separators and measurements of grade efficiency and pressure drop

International Nuclear Information System (INIS)

Koopman, Hans K.; Köksoy, Çağatay; Ertunç, Özgür; Lienhart, Hermann; Hedwig, Heinz; Delgado, Antonio

2014-01-01

Highlights: • An analytical model for efficiency is extended with additional geometrical features. • A simplified and a novel vane separator design are investigated experimentally. • Experimental results are significantly affected by re-entrainment effects. • Outlet droplet size spectra are accurately predicted by the model. • The improved grade efficiency doubles the pressure drop. - Abstract: This study investigates the predictive power of analytical models for the droplet separation efficiency of vane separators and compares experimental results of two different vane separator geometries. The ability to predict the separation efficiency of vane separators simplifies their design process, especially when analytical research allows the identification of the most important physical and geometrical parameters and can quantify their contribution. In this paper, an extension of a classical analytical model for separation efficiency is proposed that accounts for the contributions provided by straight wall sections. The extension of the analytical model is benchmarked against experiments performed by Leber (2003) on a single stage straight vane separator. The model is in very reasonable agreement with the experimental values. Results from the analytical model are also compared with experiments performed on a vane separator of simplified geometry (VS-1). The experimental separation efficiencies, computed from the measured liquid mass balances, are significantly below the model predictions, which lie arbitrarily close to unity. This difference is attributed to re-entrainment through film detachment from the last stage of the vane separators. After adjustment for re-entrainment effects, by applying a cut-off filter to the outlet droplet size spectra, the experimental and theoretical outlet Sauter mean diameters show very good agreement. A novel vane separator geometry of patented design (VS-2) is also investigated, comparing experimental results with VS-1

A new wind vane for the measurement of atmospheric turbulence

Energy Technology Data Exchange (ETDEWEB)

Parker, M.J.; Heverly, M.

1997-02-01

A Cooperative Research and Development Agreement (CRADA) between Met One Instruments, Incorporated (Met One) and Westinghouse Savannah River Company (WSRC) was created to develop a new wind vane that more accurately measures atmospheric turbulence. Through a process that had several phases, Met One created a prototype vane that was designed to attach to the existing Model 1585 Bi-Directional Wind Vane instrument structure. The prototype contained over 20% less mass to enhance responsiveness, which was also increased through the use of a teardrop-shaped fin structure. The prototype vane can be readily manufactured for commercial retail. Tests in wind tunnel of Building 735-7A, the Meteorological Engineering Facility, indicated that the new vane has a superior starting threshold of less than 0.14 meter per second, a delay distance of 0.72 meter, and a damping ratio of 0.4. The relative accuracy of less than one degree is unchanged from the previous design. The vane bias was acceptable at 0.8 degree for the horizontal wind angle, but was slightly high at 1.4 degree for the verticle wind angle. The high value of the verticle wind angle bias can most likely be reduced to the desired less than one degree value with standard manufacturing production techniques. The durability of the prototype vane was not tested in the field but is expected to be slightly less due to the use of hollow rather than foam-filled fins. However, the loss of some durability is more than compensated with increased sensitivity at low wind speeds. Field testing of the prototype is required to test for adequacy of durability.

A lightweight, biological structure with tailored stiffness: The feather vane.

Science.gov (United States)

Sullivan, Tarah N; Pissarenko, Andreï; Herrera, Steven A; Kisailus, David; Lubarda, Vlado A; Meyers, Marc A

2016-09-01

The flying feathers of birds are keratinous appendages designed for maximum performance with a minimum weight penalty. Thus, their design contains ingenious combinations of components that optimize lift, stiffness, aerodynamics, and damage resistance. This design involves two main parts: a central shaft that prescribes stiffness and lateral vanes which allows for the capture of air. Within the feather vane, barbs branch from the shaft and barbules branch from barbs, forming a flat surface which ensures lift. Microhooks at the end of barbules hold barbs tightly together, providing the close-knit, unified structure of the feather vane and enabling a repair of the structure through the reattachment of un-hooked junctions. Both the shaft and barbs are lightweight biological structures constructed of keratin using the common motif of a solid shell and cellular interior. The cellular core increases the resistance to buckling with little added weight. Here we analyze the detailed structure of the feather barb and, for the first time, explain its flexural stiffness in terms of the mechanics of asymmetric foam-filled beams subjected to bending. The results are correlated and validated with finite element modeling. We compare the flexure of single barbs as well as arrays of barbs and find that the interlocking adherence of barbs to one another enables a more robust structure due to minimized barb rotation during deflection. Thus, the flexure behavior of the feather vane can be tailored by the adhesive hooking between barbs, creating a system that mitigates damage. A simplified three-dimensional physical model for this interlocking mechanism is constructed by additive manufacturing. The exceptional architecture of the feather vane will motivate the design of bioinspired structures with tailored and unique properties ranging from adhesives to aerospace materials. Despite its importance to bird flight, literature characterizing the feather vane is extremely limited. The feather

Numerical modelling of multi-vane expander operating conditions in ORC system

Science.gov (United States)

Rak, Józef; Błasiak, Przemysław; Kolasiński, Piotr

2017-11-01

Multi-vane expanders are positive displacement volumetric machines which are nowadays considered for application in micro-power domestic ORC systems as promising alternative to micro turbines and other volumetric expanders. The multi-vane expander features very simple design, low gas flow capacity, low expansion ratios, an advantageous ratio of the power output to the external dimensions and are insensitive to the negative influence of the gas-liquid mixture expansion. Moreover, the multi-vane expander can be easily hermetically sealed, which is one of the key issues in the ORC system design. A literature review indicates that issues concerning the application of multi-vane expanders in such systems, especially related to operating of multi-vane expander with different low-boiling working fluids, are innovative, not fully scientifically described and have the potential for practical implementation. In this paper the results of numerical investigations on multi-vane expander operating conditions are presented. The analyses were performed on three-dimensional numerical model of the expander in ANSYS CFX software. The numerical model of the expander was validated using the data obtained from the experiment carried out on a lab test-stand. Then a series of computational analysis were performed using expanders' numerical model in order to determine its operating conditions under various flow conditions of different working fluids.

Split coaxial RFQ structure with modulated vanes

International Nuclear Information System (INIS)

Arai, S.

1983-10-01

A new split coaxial RFO structure with modulated vanes is proposed. The structure is designed to accelerate 238 U 4+ from 1.68 keV/u to 45.1 keV/u at frequency of 12.5 MHz. The cavity is 1.6 m in diameter and 8 m in length. The cavity consists of four cavity modules divided by three stems which support horizontal and vertical vanes periodically and alternatively. At the same time, problems on the beam dynamics and design procedures are described and discussed. (orig.)

Numerical analysis and experiment research on fluid orbital performance of vane type propellant management device

International Nuclear Information System (INIS)

Hu, Q; Li, Y; Pan, H L; Liu, J T; Zhuang, B T

2015-01-01

Vane type propellant management device (PMD) is one of the key components of the vane-type surface tension tank (STT), and its fluid orbital performance directly determines the STT's success or failure. In present paper, numerical analysis and microgravity experiment study on fluid orbital performance of a vane type PMD were carried out. By using two-phase flow model of volume of fluid (VOF), fluid flow characteristics in the tank with the vane type PMD were numerically calculated, and the rules of fluid transfer and distribution were gotten. A abbreviate model test system of the vane type PMD is established and microgravity drop tower tests were performed, then fluid management and transmission rules of the vane type PMD were obtained under microgravity environment. The analysis and tests results show that the vane type PMD has good and initiative fluid orbital management ability and meets the demands of fluid orbital extrusion in the vane type STT. The results offer valuable guidance for the design and optimization of the new generation of vane type PMD, and also provide a new approach for fluid management and control in space environment

Fluid-structure coupling in the guide vanes cascade of a pump-turbine scale model

International Nuclear Information System (INIS)

Roth, S; Hasmatuchi, V; Botero, F; Farhat, M; Avellan, F

2010-01-01

The present study concerns fluid-structure coupling phenomena occurring in a guide vane cascade of a pump-turbine scale model placed in the EPFL PF3 test rig. An advanced instrument set is used to monitor both vibrating structures and the surrounding flow. The paper highlights the interaction between vibrating guide vanes and the flow behavior. The pressure fluctuations in the stay vanes region are found to be strongly influenced by the amplitude of the vibrating guide vanes. Moreover, the flow induces different hydrodynamic damping on the vibrating guide vanes depending on the operating point of the pump-turbine.

Fluid-structure coupling in the guide vanes cascade of a pump-turbine scale model

Science.gov (United States)

Roth, S.; Hasmatuchi, V.; Botero, F.; Farhat, M.; Avellan, F.

2010-08-01

The present study concerns fluid-structure coupling phenomena occurring in a guide vane cascade of a pump-turbine scale model placed in the EPFL PF3 test rig. An advanced instrument set is used to monitor both vibrating structures and the surrounding flow. The paper highlights the interaction between vibrating guide vanes and the flow behavior. The pressure fluctuations in the stay vanes region are found to be strongly influenced by the amplitude of the vibrating guide vanes. Moreover, the flow induces different hydrodynamic damping on the vibrating guide vanes depending on the operating point of the pump-turbine.

Extension of the Vane Pump-Grinder Technology to Manufacture Finely Dispersed Meat Batters.

Science.gov (United States)

Irmscher, Stefan B; Gibis, Monika; Herrmann, Kurt; Oechsle, Anja Maria; Kohlus, Reinhard; Weiss, Jochen

2016-03-01

A vane pump-grinder system was extended to enable the manufacture of finely dispersed emulsion-type sausages by constructing and attaching a high-shear homogenizer at the outlet. We hypothesized that the dispersing capabilities of the extended system may be improved to the point of facilitating meat-fat emulsification due to an overall increased volumetric energy input EV . Coarsely ground raw material mixtures were processed to yield meat batters at varying volume flow rates (10 to 60 L/min) and rotational rotor speeds of the homogenizer nrotor (1000 to 3400 rpm). The normalized torques acting on pump, grinder, and homogenizer motors were recorded and unit power consumptions were calculated. The structure of the manufactured meat batters and sausages were analyzed via image analysis. Key physicochemical properties of unheated and heated batters, that is, texture, water-binding, color, and solubilized protein were determined. The mean diameter d10 of the visible lean meat particles varied between 352 and 406 μm whereas the mean volume-surface diameter d32 varied between 603 and 796 μm. The lightness L* ranged from 66.2 to 70.7 and correlated with the volumetric energy input and product structure. By contrast, varying process parameters did not impact color values a* (approximately 11) and b* (approximately 8). Interestingly, water-binding and protein solubilization were not affected. An exponential process-structure relationship was identified allowing manufacturers to predict product properties as a function of applied process parameters. Raw material mixtures can be continuously comminuted, emulsified, and subsequently filled into casings using an extended vane pump-grinder. © 2016 Institute of Food Technologists®

Numerical modelling of multi-vane expander operating conditions in ORC system

Directory of Open Access Journals (Sweden)

Rak Józef

2017-01-01

Full Text Available Multi-vane expanders are positive displacement volumetric machines which are nowadays considered for application in micro-power domestic ORC systems as promising alternative to micro turbines and other volumetric expanders. The multi-vane expander features very simple design, low gas flow capacity, low expansion ratios, an advantageous ratio of the power output to the external dimensions and are insensitive to the negative influence of the gas-liquid mixture expansion. Moreover, the multi-vane expander can be easily hermetically sealed, which is one of the key issues in the ORC system design. A literature review indicates that issues concerning the application of multi-vane expanders in such systems, especially related to operating of multi-vane expander with different low-boiling working fluids, are innovative, not fully scientifically described and have the potential for practical implementation. In this paper the results of numerical investigations on multi-vane expander operating conditions are presented. The analyses were performed on three-dimensional numerical model of the expander in ANSYS CFX software. The numerical model of the expander was validated using the data obtained from the experiment carried out on a lab test-stand. Then a series of computational analysis were performed using expanders' numerical model in order to determine its operating conditions under various flow conditions of different working fluids.

Vane-Cam - camshaft controls with new functionalities; Vane-Cam - Nockenwellenversteller mit neuen Funktionalitaeten

Energy Technology Data Exchange (ETDEWEB)

Knecht, A.; Pohl, D. [Hydraulik-Ring GmbH, Nuertingen (Germany); Hannibal, W. [Fachhochschule Suedwestfalen, Iserlohn (Germany). Labor fuer Konstruktion und CAE-Anwendungen; enTec Consulting GmbH, Hemer (Germany)

2007-01-15

Infinitely variable camshaft phasing systems will be used in the future in practically all gasoline internal combustion engines high volume production. This paper of Hydraulik-Ring GmbH gives an overview of the current system concepts of the latest generation of camshaft controls utilizing the principle of the vane motor. (orig.)

The Screw-Conveyor Vane Design for Piece-Wise Construction ...

African Journals Online (AJOL)

Such a method of manufacture is beyond the resources of a general-purpose metal workshop that may require the odd spiral vane once in a while and can neither afford the time nor the cost of ordering from abroad. In this article the method of six blanks which the author has developed for the building up of the vane ...

A horizontal vane radiometer: experiment, theory and simulation

OpenAIRE

Wolfe, David; Lazarra, Andres; Garcia, Alejandro

2015-01-01

The existence of two motive forces on a Crookes radiometer has complicated the investigation of either force independently. The thermal creep shear force in particular has been subject to differing interpretations of the direction in which it acts and its order of magnitude. In this article we provide a horizontal vane radiometer design which isolates the thermal creep shear force. The horizontal vane radiometer is explored through experiment, kinetic theory, and the Direct Simulation Monte C...

Vane fabrication for the proof-of-principle radio-frequency quadrupole accelerator

International Nuclear Information System (INIS)

Williams, S.W.; Potter, J.M.

1981-01-01

The electrodes for the Proof-of-Principle (POP) Radio-Frequency Quadrupole (RFQ) accelerator were machined on a numerically controlled, three-axis, vertical mill. These pole tips, or vanes, were prepared for, and used, in the successful demonstration of RFQ practicality at Los Alamos National Laboratory in February 1980. The data set that described the vanes contained about 10 million bits of tool position data. The vanes were cut from OFHC copper blanks. The tolerances achieved were approximately +- 0.005 cm. The design and manufacturing procedures are described

Solar updraft power generator with radial and curved vanes

Science.gov (United States)

Hafizh, Hadyan; Hamsan, Raziff; Zamri, Aidil Azlan Ahmad; Keprawi, Mohamad Fairuz Mohamad; Shirato, Hiromichi

2018-02-01

Solar radiation is the largest source of energy available on earth and the solar updraft power generator (SUPG) is a renewable energy facility capable of harnessing its abundant power. Unlike the conventional wind turbines that harness natural wind in the atmosphere and often encounter with the intermittent issue or even complete cut-off from airflow, the SUPG creates artificial wind as a result of solar-induced convective flows. However, the SUPG has an inherent low total efficiency due to the conversion of thermal energy into pressure energy. Acknowledging the low efficiency and considering its potential as a renewable energy facility, the current work aims to increase the total efficiency by installing a series of guide walls inside the collector. Two types of guide walls were used i.e. radial and curved vanes. The result with curved vanes showed that the updraft velocity is higher compare to those without vanes. About 18% and 64% improvement of updraft velocity and mechanical power were attained respectively. Furthermore, it was observed that the role of radial vanes configuration was more to produce a smooth updraft velocity profile rather than increasing the total efficiency.

Water table tests of proposed heat transfer tunnels for small turbine vanes

Science.gov (United States)

Meitner, P. L.

1974-01-01

Water-table flow tests were conducted for proposed heat-transfer tunnels which were designed to provide uniform flow into their respective test sections of a single core engine turbine vane and a full annular ring of helicopter turbine vanes. Water-table tests were also performed for the single-vane test section of the core engine tunnel. The flow in the heat-transfer tunnels was shown to be acceptable.

Testing of Composite Fan Vanes With Erosion-Resistant Coating Accelerated

Science.gov (United States)

Bowman, Cheryl L.; Sutter, James K.; Otten, Kim D.; Samorezov, Sergey; Perusek, Gail P.

2004-01-01

The high-cycle fatigue of composite stator vanes provided an accelerated life-state prior to insertion in a test stand engine. The accelerated testing was performed in the Structural Dynamics Laboratory at the NASA Glenn Research Center under the guidance of Structural Mechanics and Dynamics Branch personnel. Previous research on fixturing and test procedures developed at Glenn determined that engine vibratory conditions could be simulated for polymer matrix composite vanes by using the excitation of a combined slip table and electrodynamic shaker in Glenn's Structural Dynamics Laboratory. Bench-top testing gave researchers the confidence to test the coated vanes in a full-scale engine test.

Theoretical morphology and development of flight feather vane asymmetry with experimental tests in parrots.

Science.gov (United States)

Feo, Teresa J; Prum, Richard O

2014-06-01

Asymmetry in flight feather vane width is a major functional innovation associated with the evolution of flight in the ancestors of birds. However, the developmental and morphological basis of feather shape is not simple, and the developmental processes involved in vane width asymmetry are poorly understood. We present a theoretical model of feather morphology and development that describes the possible ways to modify feather development and produce vane asymmetry. Our model finds that the theoretical morphospace of feather shape is redundant, and that many different combinations of parameters could be responsible for vane asymmetry in a given feather. Next, we empirically measured morphological and developmental model parameters in asymmetric and symmetric feathers from two species of parrots to identify which combinations of parameters create vane asymmetry in real feathers. We found that both longer barbs, and larger barb angles in the relatively wider trailing vane drove asymmetry in tail feathers. Developmentally, longer barbs were the result of an offset of the radial position of the new barb locus, whereas larger barb angles were produced by differential expansion of barbs as the feather unfurls from the tubular feather germ. In contrast, the helical angle of barb ridge development did not contribute to vane asymmetry and could be indicative of a constraint. This research provides the first comprehensive description of both the morphological and developmental modifications responsible for vane asymmetry within real feathers, and identifies key steps that must have occurred during the evolution of vane asymmetry. © 2014 Wiley Periodicals, Inc.

Interaction of impeller and guide vane in a series-designed axial-flow pump

International Nuclear Information System (INIS)

Kim, S; Choi, Y S; Lee, K Y; Kim, J H

2012-01-01

In this paper, the interaction of the impeller and guide vane in a series-designed axial-flow pump was examined through the implementation of a commercial CFD code. The impeller series design refers to the general design procedure of the base impeller shape which must satisfy the various flow rate and head requirements by changing the impeller setting angle and number of blades of the base impeller. An arc type meridional shape was used to keep the meridional shape of the hub and shroud with various impeller setting angles. The blade angle and the thickness distribution of the impeller were designed as an NACA airfoil type. In the design of the guide vane, it was necessary to consider the outlet flow condition of the impeller with the given setting angle. The meridional shape of the guide vane were designed taking into consideration the setting angle of the impeller, and the blade angle distribution of the guide vane was determined with a traditional design method using vane plane development. In order to achieve the optimum impeller design and guide vane, three-dimensional computational fluid dynamics and the DOE method were applied. The interaction between the impeller and guide vane with different combination set of impeller setting angles and number of impeller blades was addressed by analyzing the flow field of the computational results.

Study on effects of mixing vane grids on coolant temperature distribution by subchannel analysis

Energy Technology Data Exchange (ETDEWEB)

Mao, H.; Yang, B.W.; Han, B. [Xi' an Jiaotong Univ., Shaanxi (China). Science and Technology Center for Advanced Nuclear Fuel Research

2016-07-15

Mixing vane grids (MVG) have great influence on coolant temperature field in the rod bundle. The MVG could enhance convective heat transfer between the fuel rod wall and the coolant, and promote inter-subchannel mixing at the same time. For the influence of the MVG on convective heat transfer enhancement, many experiments have been done and several correlations have been developed based on the experimental data. However, inter-subchannel mixing promotion caused by the MVG is not well estimated in subchannel analysis because the information of mixing vanes is totally missing in most subchannel codes. This paper analyzes the influence of mixing vanes on coolant temperature distribution using the improved MVG model in subchannel analysis. The coolant temperature distributions with the MVG are analyzed, and the results show that mixing vanes lead to a more uniform temperature distribution. The performances of split vane grids under different power conditions are evaluated. The results are compared with those of spacer grids without mixing vanes and some conclusions are obtained.

Study on effects of mixing vane grids on coolant temperature distribution by subchannel analysis

International Nuclear Information System (INIS)

Mao, H.; Yang, B.W.; Han, B.

2016-01-01

Mixing vane grids (MVG) have great influence on coolant temperature field in the rod bundle. The MVG could enhance convective heat transfer between the fuel rod wall and the coolant, and promote inter-subchannel mixing at the same time. For the influence of the MVG on convective heat transfer enhancement, many experiments have been done and several correlations have been developed based on the experimental data. However, inter-subchannel mixing promotion caused by the MVG is not well estimated in subchannel analysis because the information of mixing vanes is totally missing in most subchannel codes. This paper analyzes the influence of mixing vanes on coolant temperature distribution using the improved MVG model in subchannel analysis. The coolant temperature distributions with the MVG are analyzed, and the results show that mixing vanes lead to a more uniform temperature distribution. The performances of split vane grids under different power conditions are evaluated. The results are compared with those of spacer grids without mixing vanes and some conclusions are obtained.

Performance improvement of a centrifugal compressor stage by using different vaned diffusers

International Nuclear Information System (INIS)

Zhang, Y C; Kong, X Z; Li, F; Sun, W; Chen, Q G

2013-01-01

The vaneless diffuser (VLD) is usually adopted in the traditional design of the multi-stage centrifugal compressor because of the stage's match problem. The drawback of the stage with vaneless diffusers is low efficiency. In order to increase the efficiency and at the same time, induce no significant decline in the operating range of the stage, three different types of vaned diffusers are designed and numerically investigated: the traditional vaned diffuser (TVD), the low-solidity cascade diffuser (LSD) and the partial-height vane diffuser (PVD). These three types of vaned diffusers have different influences on the performance of the centrifugal compressor. In the present investigation, the first part investigates the performance of a centrifugal compressor stage with three different vaned diffusers. The second part studies the influences of the height and the position of partial height vanes on the stage performance, and discusses the matching problem between the PVD and the downstream return channel. The stage investigated in this paper includes the impeller, the diffuser, the bend and the return channel. In the process of numerical investigation, the flow is assumed to be steady, and this process includes calculation and simulation. The calculation of 3-D turbulent flow in the stage uses the commercial CFD code NUMECA together with the Spalart-Allmaras turbulence model. The simulation of the computational region includes the impeller passages, the diffuser passages and return channel passages. The structure and surrounding region are assumed to have a perfect cyclic symmetry, so the single channel model and periodic boundary condition are applied at the middle of the passage, that is to reduce the calculation region to only one region. The investigation showed that the low-solidity cascade diffuser would be a better choice as a middle course for the first stage of the multistage centrifugal compressor. Besides, the influences of the height and the position

Experimental Study on Series Operation of Sliding Vane Pump and Centrifugal Pump

OpenAIRE

Li, Tao; Zhang, Weiming; Jiang, Ming; Li, Zhengyang

2013-01-01

A platform for sliding vane pump and centrifugal pump tests is installed to study the series operation of them under different characteristics of pipeline. Firstly, the sliding vane pump and the centrifugal pump work independently, and the performance is recorded. Then, the two types of pumps are combined together, with the sliding vane pump acting as the feeding pump. Comparison is made between the performance of the independently working pump and the performance of series operation pump. Re...

Numerical Analysis of a Centrifugal Fan for Improved Performance using Splitter Vanes

OpenAIRE

N. Yagnesh Sharma; K. Vasudeva Karanth

2009-01-01

The flow field in a centrifugal fan is highly complex with flow reversal taking place on the suction side of impeller and diffuser vanes. Generally performance of the centrifugal fan could be enhanced by judiciously introducing splitter vanes so as to improve the diffusion process. An extensive numerical whole field analysis on the effect of splitter vanes placed in discrete regions of suspected separation points is possible using CFD. This paper examines the effect of sp...

Twisted Vanes Would Enhance Fuel/Air Mixing In Turbines

Science.gov (United States)

Nguyen, H. Lee; Micklow, Gerald J.; Dogra, Anju S.

1994-01-01

Computations of flow show performance of high-shear airblast fuel injector in gas-turbine engine enhanced by use of appropriately proportioned twisted (instead of flat) dome swirl vanes. Resultant more nearly uniform fuel/air mixture burns more efficiently, emitting smaller amounts of nitrogen oxides. Twisted-vane high-shear airblast injectors also incorporated into paint sprayers, providing advantages of low pressure drop characteristic of airblast injectors in general and finer atomization of advanced twisted-blade design.

Pressure Drop Test of Hybrid Mixing Vane Spacer Grid

Energy Technology Data Exchange (ETDEWEB)

Oh, D. S.; Chang, S. K.; Kim, B. D.; Chun, S. Y.; Chun, T. H

2007-08-15

The pressure loss test has been accomplished in the test section containing 5x5 rod bundle with a length of 2 m including 3 spacer grids. The test has been performed for the 5 kinds of spacer grids to compare the pressure loss characteristics: 1. Plain spacer grid which has the same body of the Hybrid but without vane (Plain), 2. Hybrid Vane spacer grid (Hybrid), 3. Hybrid-SC spacer grid which is constructed with coined, chamfered strip and is fabricated by spot welding, 4. Hybrid-LC spacer grid which is constructed with coined, chamfered strip and is fabricated by line welding along intersection line, 5. Westinghouse spacer grid with split vane (Plus-7). The pressure loss coefficient of the Plain, Hybrid, Hybrid-SC, Hybrid-LC, and Plus-7 spacer grid is 0.93, 1.15, 1.02, 1.04, and 1.08, respectively.

75 FR 7469 - Panel Member List for Hydropower Licensing Study Dispute Resolution; Notice Extending Filing Date...

Science.gov (United States)

2010-02-19

... List for Hydropower Licensing Study Dispute Resolution; Notice Extending Filing Date for Applications for Panel Member List for Hydropower Licensing Study Dispute Resolution February 4, 2010. On October... on a list of resource experts willing to serve as a third panel member in the Commission's hydropower...

On the study of wavy leading-edge vanes to achieve low fan interaction noise

Science.gov (United States)

Tong, Fan; Qiao, Weiyang; Xu, Kunbo; Wang, Liangfeng; Chen, Weijie; Wang, Xunnian

2018-04-01

The application of wavy leading-edge vanes to reduce a single-stage axial fan noise is numerically studied. The aerodynamic and acoustic performance of the fan is numerically investigated using a hybrid unsteady Reynolds averaged Navier-Stokes (URANS)/acoustic analogy method (Goldstein equations). First, the hybrid URANS/Goldstein method is developed and successfully validated against experiment results. Next, numerical simulations are performed to investigate the noise reduction effects of the wavy leading-edge vanes. The aerodynamic and acoustic performance is assessed for a fan with vanes equipped with two different wavy leading-edge profiles and compared with the performance of conventional straight leading-edge vanes. Results indicate that a fan with wavy leading-edge vanes produces lower interaction noise than the baseline fan without a significant loss in aerodynamic performance. In fact, it is demonstrated that wavy leading-edge vanes have the potential to lead to both aerodynamic and acoustic improvements. The two different wavy leading-edge profiles are shown to successfully reduce the fan tone sound power level by 1.2 dB and 4.3 dB, respectively. Fan efficiency is also improved by about 1% with one of the tested wavy leading-edge profiles. Large eddy simulation (LES) is also performed for a simplified fan stage model to assess the effects of wavy leading-edge vanes on the broadband fan noise. Results indicate that the overall sound power level of a fan can be reduced by about 4 dB with the larger wavy leading-edge profile. Finally, the noise reduction mechanisms are investigated and analysed. It is found that the wavy leading-edge profiles can induce significant streamwise vorticity around the leading-edge protuberances and reduce pressure fluctuations (especially at locations of wavy leading-edge hills) and unsteady forces on the stator vanes. The underlying mechanism of the reduced pressure fluctuations is also discussed by examining the magnitude

Design and experimental validation of the inlet guide vane system of a mini hydraulic bulb-turbine

Energy Technology Data Exchange (ETDEWEB)

Ferro, L.M.C. [Department of Mechanical Engineering, Escola Superior de Tecnologia de Setubal, Polytechnic Institute of Setubal, Campus do IPS, Estefanilha, 2910-761 Setubal (Portugal); IDMEC, Instituto Superior Tecnico, Technical University of Lisbon, Av. Rovisco Pais,1049-001 Lisboa (Portugal); Gato, L.M.C.; Falcao, A.F.O. [IDMEC, Instituto Superior Tecnico, Technical University of Lisbon, Av. Rovisco Pais,1049-001 Lisboa (Portugal)

2010-09-15

The paper presents a fast design method for the inlet guide vanes of low-cost mini hydraulic bulb turbines. The guide vanes are positioned between two conical surfaces with a common vertex and have constant thickness distribution, except close to the leading and the trailing edges. The conical-walled inlet guide vane row is designed using a quasi-three-dimensional calculation method, by prescribing the angular-momentum distribution along the span at the outlet section of the guide vanes. The meridional through-flow is computed by a streamline curvature method and the blade-to-blade flow by a singularity surface method. The stagger angle and the vane camber are computed to fulfil the required design circulation and zero-incidence flow at the leading edge. The final vane shape is a single-curvature surface with straight leading and trailing edges. To validate the design method, a conical-walled inlet guide vane row nozzle-model with six fixed vanes was designed, manufactured and tested in an airflow rig. Traversing measurements along the circumferential and radial directions were made with a five-hole probe. The experimental results are compared with the prescribed design conditions and with numerical results from the three-dimensional inviscid and viscous flow computed with the FLUENT code. (author)

Control rod velocity limiter

International Nuclear Information System (INIS)

Cearley, J.E.; Carruth, J.C.; Dixon, R.C.; Spencer, S.S.; Zuloaga, J.A. Jr.

1986-01-01

This patent describes a velocity control arrangement for a reciprocable, vertically oriented control rod for use in a nuclear reactor in a fluid medium, the control rod including a drive hub secured to and extending from one end therefrom. The control device comprises: a toroidally shaped control member spaced from and coaxially positioned around the hub and secured thereto by a plurality of spaced radial webs thereby providing an annular passage for fluid intermediate the hub and the toroidal member spaced therefrom in coaxial position. The side of the control member toward the control rod has a smooth generally conical surface. The side of the control member away from the control rod is formed with a concave surface constituting a single annular groove. The device also comprises inner and outer annular vanes radially spaced from one another and spaced from the side of the control member away from the control rod and positioned coaxially around and spaced from the hub and secured thereto by spaced radial webs thereby providing an annular passage for fluid intermediate the hub and the vanes. The vanes are angled toward the control member, the outer edge of the inner vane being closer to the control member and the inner edge of the outer vane being closer to the control member. When the control rod moves in the fluid in the direction toward the drive hub the vanes direct a flow of fluid turbulence which provides greater resistance to movement of the control rod in the direction toward the drive hub than in the other direction

Research and development on the hydraulic design system of the guide vanes of multistage centrifugal pumps

International Nuclear Information System (INIS)

Zhang, Q H; Xu, Y; Shi, W D; Lu, W G

2012-01-01

To improve the hydraulic design accuracy and efficiency of the guide vanes of the multistage centrifugal pumps, four different-structured guide vanes are investigated, and the design processes of those systems are established. The secondary development platforms of the ObjectArx2000 and the UG/NX OPEN are utilized to develop the hydraulic design systems of the guide vanes. The error triangle method is adopted to calculate the coordinates of the vanes, the profiles of the vanes are constructed by Bezier curves, and then the curves of the flow areas along the flow-path are calculated. Two-dimensional and three-dimensional hydraulic models can be developed by this system.

ESRC guide vanes of hydraulic turbine for Three Gorges project

Directory of Open Access Journals (Sweden)

Rui CHEN

2005-05-01

Full Text Available The mechanical properties and internal quality of low carbon martensite Electroslag Remelting Casting (ESRCstainless steel castings are superior to that of sand casting ones. The key technologies for the equipments and ESRC processes have been resolved during the experimental research period of guide vanes of hydraulic turbines for Three Gorges project. And ESRC guide vanes of hydraulic turbines for Three Gorges project have been produced successfully.

Study of turbine and guide vanes integration to enhance the performance of cross flow vertical axis wind turbine

Science.gov (United States)

Wibowo, Andreas; Tjahjana, Dominicus Danardono Dwi Prija; Santoso, Budi; Situmorang, Marcelinus Risky Clinton

2018-02-01

The main purpose of this study is to investigate the best configuration between guide vanes and cross flow vertical axis wind turbine with variation of several parameters including guide vanes tilt angle and the number of turbine and guide vane blades. The experimental test were conducted under various wind speed and directions for testing cross flow wind turbine, consisted of 8, 12 and 16 blades. Two types of guide vane were developed in this study, employing 20° and 60° tilt angle. Both of the two types of guide vane had three variations of blade numbers which had same blade numbers variations as the turbines. The result showed that the configurations between 60° guide vane with 16 blade numbers and turbine with 16 blade numbers had the best configurations. The result also showed that for certain configuration, guide vane was able to increase the power generated by the turbine significantly by 271.39% compared to the baseline configuration without using of guide vane.

Hydraulic analysis of river training cross-vanes as part of post-restoration monitoring

Directory of Open Access Journals (Sweden)

T. A. Endreny

2011-07-01

Full Text Available River restoration design methods are incrementally improved by studying and learning from monitoring data in previous projects. In this paper we report post-restoration monitoring data and simulation analysis for a Natural Channel Design (NCD restoration project along 1600 m of the Batavia Kill (14 km² watershed in the Catskill Mountains, NY. The restoration project was completed in 2002 with goals to reduce bank erosion and determine the efficacy of NCD approaches for restoring headwater streams in the Catskill Mountains, NY. The NCD approach used a reference-reach to determine channel form, empirical relations between the project site and reference site bankfull dimensions to size channel geometry, and hydraulic and sediment computations based on a bankfull (1.3 yr return interval discharge to test channel capacity and sediment stability. The NCD project included 12 cross-vanes and 48 j-hook vanes as river training structures along 19 meander bends to protect against bank erosion and maintain scour pools for fish habitat. Monitoring data collected from 2002 to 2004 were used to identify aggradation of pools in meander bends and below some structures. Aggradation in pools was attributed to the meandering riffle-pool channel trending toward step-pool morphology and cross-vane arms not concentrating flow in the center of the channel. The aggradation subsequently caused flow splitting and 4 partial point bar avulsions during a spring 2005 flood with a 25-yr return interval. Processing the pre-flood monitoring data with hydraulic analysis software provided clues the reach was unstable and preventative maintenance was needed. River restoration and monitoring teams should be trained in robust hydraulic analytical methods that help them extend project restoration goals and structure stability.

Design and Analysis of a Split Deswirl Vane in a Two-Stage Refrigeration Centrifugal Compressor

Directory of Open Access Journals (Sweden)

Jeng-Min Huang

2014-09-01

Full Text Available This study numerically investigated the influence of using the second row of a double-row deswirl vane as the inlet guide vane of the second stage on the performance of the first stage in a two-stage refrigeration centrifugal compressor. The working fluid was R134a, and the turbulence model was the Spalart-Allmaras model. The parameters discussed included the cutting position of the deswirl vane, the staggered angle of two rows of vane, and the rotation angle of the second row. The results showed that the performance of staggered angle 7.5° was better than that of 15° or 22.5°. When the staggered angle was 7.5°, the performance of cutting at 1/3 and 1/2 of the original deswirl vane length was slightly different from that of the original vane but obviously better than that of cutting at 2/3. When the staggered angle was 15°, the cutting position influenced the performance slightly. At a low flow rate prone to surge, when the second row at a staggered angle 7.5° cutting at the half of vane rotated 10°, the efficiency was reduced by only about 0.6%, and 10% of the swirl remained as the preswirl of the second stage, which is generally better than other designs.

CMC vane assembly apparatus and method

Science.gov (United States)

Schiavo, Anthony L; Gonzalez, Malberto F; Huang, Kuangwei; Radonovich, David C

2012-10-23

A metal vane core or strut (64) is formed integrally with an outer backing plate (40). An inner backing plate (38) is formed separately. A spring (74) with holes (75) is installed in a peripheral spring chamber (76) on the strut. Inner and outer CMC shroud covers (46, 48) are formed, cured, then attached to facing surfaces of the inner and outer backing plates (38, 40). A CMC vane airfoil (22) is formed, cured, and slid over the strut (64). The spring (74) urges continuous contact between the strut (64) and airfoil (66), eliminating vibrations while allowing differential expansion. The inner end (88) of the strut is fastened to the inner backing plate (38). A cooling channel (68) in the strut is connected by holes (69) along the leading edge of the strut to peripheral cooling paths (70, 71) around the strut. Coolant flows through and around the strut, including through the spring holes.

Performance improvement of centrifugal compressor stage with pinched geometry or vaned diffuser

Energy Technology Data Exchange (ETDEWEB)

Jaatinen, A.

2009-07-01

Centrifugal compressors are widely used for example in refrigeration processes, the oil and gas industry, superchargers, and waste water treatment. In this work, five different vaneless diffusers and six different vaned diffusers are investigated numerically. The vaneless diffusers vary only by their diffuser width, so that four of the geometries have pinch implemented to them. Pinch means a decrease in the diffuser width. Four of the vaned diffusers have the same vane turning angle and a different number of vanes, and two have different vane turning angles. The flow solver used to solve the flow fields is Finfo, which is a Navier-Stokes solver. All the cases are modeled Chien's k-epsilon turbulence model. All five vaneless diffusers and three vaned diffusers are investigated also experimentally. For each construction, the compressor operating map is measured according to relevant standards. In addition to this, the flow fields before and after the diffuser are measured with static and total pressure, flow angle and total temperature measurements k-omega SST turbulence model. The simulation results indicate that it is possible to improve the efficiency with the pinch, and according to the numerical results, the two best geometries are the ones with most pinch at the shroud. These geometries have approximately 4 percentage points higher effciency than the unpinched vaneless diffusers. The hub pinch does not seem to have any major benefits. In general, the pinches make the flow fields before and after the diffuser more uniform. The pinch also seems to improve the impeller effciency. This is down to two reasons. The major reason is that the pinch decreases the size of slow flow and possible backflow region located near the shroud after the impeller. Secondly, the pinches decrease the flow velocity in the tip clearance, leading to a smaller tip leakage flow and therefore slightly better impeller efficiency. Also some of the vaned diffusers improve the efficiency

Discussion on the re-irradiated fuel assembly with damaged guide vanes

International Nuclear Information System (INIS)

Li Ligang

2013-01-01

In January 2011, during the second plant of CNNC Nuclear Power Operations Management Co., Ltd.(hereinafter referred to as the second plant) refueling outage, the visual inspection found the guide vanes of fuel assembly A had felling off. After the National Nuclear Safety Administration (NNSA) estimated and approved, the fuel assembly A was reloaded in the specified location of reactor core. During the refueling outage in March 2012, the fuel assembly A was removed again from the reactor core. Visual inspection confirmed that the fuel assembly A was complete and without abnormal changes. The practice provides reference for re-irradiated of fuel assembly with the same type of damaged guide vanes, and provides case support for standard development for the same type of re-irradiated fuel assembly with damaged guide vanes. (author)

Effect of spacer grid mixing vanes on coolant outlet temperature distribution

Energy Technology Data Exchange (ETDEWEB)

Raemae, Tommi; Lahtinen, Tuukka; Brandt, Tellervo; Toppila, Timo [Fortum Power and Heat, Fortum (Finland). Nuclear Competence Center

2012-08-15

In Loviisa VVER-440-type NPP the coolant outlet temperature of the hot subchannel is constantly monitored during the operation. According to the authority requirement the maximum subchannel outlet temperature must not exceed the saturation temperature. Coolant temperature distribution inside the fuel assembly is affected by the efficiency of the coolant mixing. In order to enhance the coolant mixing the fuel manufacturer is introducing the additional mixing vanes on the fuel bundle spacer grids. In the paper the effect of the different mixing vane modifications is studied with computational fluid dynamics (CFD) simulation. Goal of the modelling is to find vane modifications with which sufficient mixing is reached with acceptable increase in the spacer grid pressure loss. The results of the studies are discussed in the paper. (orig.)

Numerical prediction for effects of guide vane blade numbers on hydraulic turbine performance

International Nuclear Information System (INIS)

Shi, F X; Yang, J H; Wang, X H; Li, C E

2013-01-01

Using unstructured hybrid grid technique and SIMPLEC algorithm,a general three-dimensional simulation based on Reynolds Navier- stocks in multiple reference frames and the RNG k-ε turbulence model, is presented for the reversal centrifugal pump (PAT) with a guide vane. Four different schemes are designed by a change of the number of guide vane blade of PAT. The inner flow field in every scheme is simulated, accordingly, the external characteristic and static pressure distribution in flow field in PAT is obtained. The results obtained show that the efficiency can be improved by adding a guide vane for the PAT, besides, the high efficiency area is wider than before. Guide blade numbers changed, external characteristics of turbine changed, and the external characteristic changed. The optimal value is existent for the guide vane blade number, which has a great impact on the distribution of pressure in runner inlet

Design and numerical investigation of swirl recovery vanes for the Fokker 29 propeller

Directory of Open Access Journals (Sweden)

Wang Yangang

2014-10-01

Full Text Available Swirl recovery vanes (SRVs are a set of stationary vanes located downstream from a propeller, which may recover some of the residual swirl from the propeller, hoping for an improvement in both thrust and efficiency. The SRV concept design for a scaled version representing the Fokker 29 propeller is performed in this paper, which may give rise to a promotion in propulsive performance of this traditional propeller. Firstly the numerical strategy is validated from two aspects of global quantities and the local flow field of the propeller compared with experimental data, and then the exit flow together with the development of propeller wake is analyzed in detail. Three kinds of SRV are designed with multiple circular airfoils. The numerical results show that the swirl behind the propeller is recovered significantly with Model V3, which is characterized by the highest solidity along spanwise, for various working conditions, and the combination of rotor and vane produced 5.76% extra thrust at the design point. However, a lower efficiency is observed asking for a better vane design and the choice of a working point. The vane position is studied which shows that there is an optimum range for higher thrust and efficiency.

Static thrust-vectoring performance of nonaxisymmetric convergent-divergent nozzles with post-exit yaw vanes. M.S. Thesis - George Washington Univ., Aug. 1988

Science.gov (United States)

Foley, Robert J.; Pendergraft, Odis C., Jr.

1991-01-01

A static (wind-off) test was conducted in the Static Test Facility of the 16-ft transonic tunnel to determine the performance and turning effectiveness of post-exit yaw vanes installed on two-dimensional convergent-divergent nozzles. One nozzle design that was previously tested was used as a baseline, simulating dry power and afterburning power nozzles at both 0 and 20 degree pitch vectoring conditions. Vanes were installed on these four nozzle configurations to study the effects of vane deflection angle, longitudinal and lateral location, size, and camber. All vanes were hinged at the nozzle sidewall exit, and in addition, some were also hinged at the vane quarter chord (double-hinged). The vane concepts tested generally produced yaw thrust vectoring angles much less than the geometric vane angles, for (up to 8 percent) resultant thrust losses. When the nozzles were pitch vectored, yawing effectiveness decreased as the vanes were moved downstream. Thrust penalties and yawing effectiveness both decreased rapidly as the vanes were moved outboard (laterally). Vane length and height changes increased yawing effectiveness and thrust ratio losses, while using vane camber, and double-hinged vanes increased resultant yaw angles by 50 to 100 percent.

Numerical and experimental study of the leakage flow in guide vanes with different hydrofoils

Directory of Open Access Journals (Sweden)

Sailesh Chitrakar

2017-07-01

Full Text Available Clearance gaps between guide vanes and cover plates of Francis turbines tend to increase in size due to simultaneous effect of secondary flow and erosion in sediment affected hydropower plants. The pressure difference between the two sides of the guide vane induces leakage flow through the gap. This flow enters into the suction side with high acceleration, disturbing the primary flow and causing more erosion and losses in downstream turbine components. A cascade rig containing a single guide vane passage has been built to study the effect of the clearance gap using pressure sensors and PIV (Particle Image Velocimetry technique. This study focuses on developing a numerical model of the test rig, validating the results with experiments and investigating the behavior of leakage flow numerically. It was observed from both CFD and experiment that the leakage flow forms a passage vortex, which shifts away from the wall while travelling downstream. The streamlines contributing to the formation of this vortex have been discussed. Furthermore, the reference guide vane with symmetrical hydrofoil has been compared with four cambered profiles, in terms of the guide vane loading and the consequent effect on the leakage flow. A dimensionless term called Leakage Flow Factor (Lff has been introduced to compare the performances of hydrofoils. It is shown that the leakage flow and its effect on increasing losses and erosion can be minimized by changing the pressure distribution over the guide vane.

Influence of blockage effect on measurement by vane anemometers

Directory of Open Access Journals (Sweden)

Sluse Jan

2017-01-01

Full Text Available The article deals with influence of blockage effect caused by vane anemometer in the wind tunnel by measurement via this anemometer. The influences will be represented by correction coefficient. The first part of this article is focused on the design of the impeller of vane anemometers. The impellers are printed on 3D printer with variable parameters. The anemometer is fixed in an open section of the wind tunnel with closed loop and the velocity profile is measured by Laser Doppler velocimetry (LDV in front and behind it for all impellers. The experimental data are compared with the numerical simulation in OpenFOAM. The results are correction coefficients.

Analysis on influence of guide vanes closure laws of pump-turbine on load rejection transient process

Science.gov (United States)

Yao, Z.; Bi, H. L.; Huang, Q. S.; Li, Z. J.; Wang, Z. W.

2013-12-01

In load rejection transient process, the sudden shut down of guide vanes may cause units speed rise and a sharp increase in water hammer pressure of diversion system, which endangers the safety operation of the power plant. Adopting reasonable guide vane closure law is a kind of economic and effective measurement to reduce the water hammer pressure and limit rotational speed increases. In this paper, combined with Guangzhou Pumped Storage Power Station plant A, the load rejection condition under different guide vanes closure laws is calculated and the key factor of guide vanes closure laws on the impact of the load rejection transition process is analyzed. The different inflection points, which are the closure modes, on the impact of unit speed change, water level fluctuation of surge tank, and the pressure fluctuation of volute inlet and draft tube inlet are further discussed. By compared with the calculation results, a reasonable guide vanes inflection point position can be determined according to security requirements and a reasonable guide vanes closure law can be attained to effectively coordinate the unit speed rise and the rapid pressure change in the load rejection transient process.

Effects of the friction coefficient on the torque characteristics of a hydraulic cam-rotor vane motor

Energy Technology Data Exchange (ETDEWEB)

Ma, Qiankun; Wang, Xuyong; Yuan, Fan; Chen, Liang Shen; Tao, Jian Feng [School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai (China); Miao, Zhong Hua [School of Mechatronic Engineering and Automation, Shanghai University, Shanghai (China)

2016-08-15

The friction coefficient between the vane and the slot is one of the most critical factors that affects the performance of a continuous rotary hydraulic cam-rotor vane motor. To study the effects of this coefficient on the torque characteristics of the motor, the mathematical model for the normal force and the disturbing torque between the cam rotors and the vanes of the motor was established by analyzing the forces exerted on the vanes. The mathematical model was simulated with MATLAB, and simulation results show that an increase in the friction coefficient would simultaneously decrease the normal force and increase the disturbing torque, which would negatively affect the performance of the motor. Further experimental research indicated that the low-speed performance of the hydraulic cam-rotor motor was significantly improved when the friction coefficient was reduced by controlling the parallelism tolerance, flatness and roughness between the vanes and the slots.

Evaluation of effect of low opening operation on increasing wear of bearing bushings of guide vanes used in hydropower plants

International Nuclear Information System (INIS)

Kim, Jong Sung; Kim, Se Na

2012-01-01

A guide vane plays a key role in controlling the flow rate of water supplied to the turbine of a hydropower plant. It has been reported that guide vane bearing bushings are subjected to considerable wear, which requires them to be maintained. An ancillary service such as frequency control and black start causes cyclic low opening operation of the guide vanes. It is empirically well known that such operation increases the wear rate of the guide vane bearing bushing. In this study, the effect of low opening operation on the increasing wear of the guide vane bearing bushing is quantitatively assessed via finite element flow analysis, finite element stress analysis, and relative wear evaluation. As a result of the assessment, it is identified that the pressure applied on the guide vane surface increases and the contact length between the outer surface of the guide vane stem and the inner surface of the bearing bushing decreases with a decrease in the opening of the guide vane. In addition, low opening of the guide vanes results in an increase in the relative wear owing to the generation of high contact pressure on the bearing bushing surfaces

A three dimensional model of a vane rheometer

International Nuclear Information System (INIS)

Nazari, Behzad; Moghaddam, Ramin Heidari; Bousfield, Douglas

2013-01-01

Highlights: • FEM was used to calculate the isothermal flow parameters in a vane geometry. • Velocity, pressure and then stress fields were obtained. • Using total stress, shaft torque was calculated to compare with experimental data. • A modified cell Reynolds number and power number were used to study flow pattern. • A comparison between 2D and 3D modeling was done based on calculated torques. -- Abstract: Vane type geometries are often used in rheometers to avoid slippage between the sample and the fixtures. While yield stress and other rheological properties can be obtained with this geometry, a complete analysis of this complex flow field is lacking in the literature. In this work, a finite element method is used to calculate the isothermal flow parameters in a vane geometry. The method solves the mass and momentum continuity equations to obtain velocity, pressure and then stress fields. Using the total stress numerical data, we calculated the torque applied on solid surfaces. The validity of the computational model was established by comparing the results to experimental results of shaft torque at different angular velocities. The conditions where inertial terms become important and the linear relationship between torque and stress are quantified with dimensionless groups. The accuracy of a two dimensional analysis is compared to the three dimensional results

The image evaluation of iterative motion correction reconstruction algorithm PROPELLER T2-weighted imaging compared with MultiVane T2-weighted imaging

Science.gov (United States)

Lee, Suk-Jun; Yu, Seung-Man

2017-08-01

The purpose of this study was to evaluate the usefulness and clinical applications of MultiVaneXD which was applying iterative motion correction reconstruction algorithm T2-weighted images compared with MultiVane images taken with a 3T MRI. A total of 20 patients with suspected pathologies of the liver and pancreatic-biliary system based on clinical and laboratory findings underwent upper abdominal MRI, acquired using the MultiVane and MultiVaneXD techniques. Two reviewers analyzed the MultiVane and MultiVaneXD T2-weighted images qualitatively and quantitatively. Each reviewer evaluated vessel conspicuity by observing motion artifacts and the sharpness of the portal vein, hepatic vein, and upper organs. The signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) were calculated by one reviewer for quantitative analysis. The interclass correlation coefficient was evaluated to measure inter-observer reliability. There were significant differences between MultiVane and MultiVaneXD in motion artifact evaluation. Furthermore, MultiVane was given a better score than MultiVaneXD in abdominal organ sharpness and vessel conspicuity, but the difference was insignificant. The reliability coefficient values were over 0.8 in every evaluation. MultiVaneXD (2.12) showed a higher value than did MultiVane (1.98), but the difference was insignificant ( p = 0.135). MultiVaneXD is a motion correction method that is more advanced than MultiVane, and it produced an increased SNR, resulting in a greater ability to detect focal abdominal lesions.

Effect of Guide Vane Clearance Gap on Francis Turbine Performance

Directory of Open Access Journals (Sweden)

Ravi Koirala

2016-04-01

Full Text Available Francis turbine guide vanes have pivoted support with external control mechanism, for conversion of pressure to kinetic energy and to direct them to runner vanes. This movement along the support is dependent on variation of load and flow (operating conditions. Small clearance gaps between facing plates and the upper and lower guide vane tips are available to aid this movement, through which leakage flow occurs. This secondary flow disturbs the main flow stream, resulting performance loss. Additionally, these increased horseshoe vortex, in presence of sand, when crosses through the gaps, both the surfaces are eroded. This causes further serious effect on performance and structural property by increasing gaps. This paper discusses the observation of the severity in hydropower plants and effect of clearance gaps on general performance of the Francis turbine through computational methods. It also relates the primary result with the empirical relation for leakage flow prediction. Additionally, a possible method to computationally estimate thickness depletion has also been presented. With increasing clearance gap, leakage increases, which lowers energy conversion and turbine efficiency along with larger secondary vortex.

Performance of an alpha-vane and pitot tube in simulated heavy rain environment

Science.gov (United States)

Luers, J. K.; Fiscus, I. B.

1985-01-01

Experimental tests were conducted in the UDRI Environmental Wind/Rain Tunnel to establish the performance of an alpha-vane, that measures angle of attack, in a simulated heavy rain environment. The tests consisted of emersing the alpha-vane in an airstream with a concurrent water spray penetrating vertically through the airstream. The direction of the spray was varied to make an angle of 5.8 to 18 deg with the airstream direction in order to simulate the conditions that occur when an aircraft lands in a heavy rain environment. Rainrates simulated varied from 1000 to 1200 mm/hr which are the most severe ever expected to be encountered by an aircraft over even a 30 second period. Tunnel airspeeds ranged from 85 to 125 miles per hour. The results showed that even the most severe rainrates produced a misalignment in the alpha-vane of only 1 deg away from the airstream direction. Thus for normal rain conditions experienced by landing aircraft no significant deterioration in alpha-vane performance is expected.

Precision Model for Microwave Rotary Vane Attenuator

DEFF Research Database (Denmark)

Guldbrandsen, Tom

1979-01-01

A model for a rotary vane attenuator is developed to describe the attenuator reflection and transmission coefficients in detail. All the parameters of the model can be measured in situ, i.e., without diassembling any part. The tranmission errors caused by internal reflections are calculated from ...

Design optimization of a T mixing vane in nuclear fuel assembly

International Nuclear Information System (INIS)

Jung, Sang-Ho; Moon, Mi-Ae; Kim, Kwang-Yong

2009-01-01

The purposes of present work are to analyze the convective heat transfer with three-dimensional Reynolds-averaged Navier-Stokes analysis, and to optimize shape of the mixing vane using the analysis results. PLUS7 that is designed by KNF and Westinghouse is used as reference geometry. Shear stress transport turbulence model is used as a turbulence closure. Two bend angles of mixing vane are selected as design variable. The objective function is defined as a combination of inverse of heat transfer rate and friction loss. Response surface method is employed as an optimization technique. The calculation domains of 1x2 geometry are analyzed with translational and rotational periodic boundary conditions which take flow directions into account. The fluid flow and heat transfer characteristics have been explained through velocity vectors, streamlines and Nusselt numbers. The results show that the optimized geometry improves the heat transfer performance of the mixing vane with a relatively small pressure drop increment and has higher Critical Heat Flux. (author)

Flow control in axial fan inlet guide vanes by synthetic jets

Directory of Open Access Journals (Sweden)

Wurst P.

2013-04-01

Full Text Available Tested high pressure axial flow fan with hub/tip ratio of 0.70 and external diameter of 600 mm consisted of inlet guide vanes (IGV, rotor and stator blade rows. Fan peripheral velocity was 47 m/s. Air volume flow rate was changed by turning of rear part of the inlet guide vanes. At turning of 20 deg the flow was separated on the IGV profiles. The synthetic jets were introduced through radial holes in machine casing in the location before flow separation origin. Synthetic jet actuator was designed with the use of a speaker by UT AVCR. Its membrane had diameter of 63 mm. Excitation frequency was chosen in the range of 500 Hz – 700 Hz. Synthetic jets favourably influenced separated flow on the vane profiles in the distance of (5 – 12 mm from the casing surface. The reduction of flow separation area caused in the region near the casing the decrease of the profile loss coefficient approximately by 20%.

Flow control in axial fan inlet guide vanes by synthetic jets

Science.gov (United States)

Cyrus, V.; Trávníček, Z.; Wurst, P.; Kordík, J.

2013-04-01

Tested high pressure axial flow fan with hub/tip ratio of 0.70 and external diameter of 600 mm consisted of inlet guide vanes (IGV), rotor and stator blade rows. Fan peripheral velocity was 47 m/s. Air volume flow rate was changed by turning of rear part of the inlet guide vanes. At turning of 20 deg the flow was separated on the IGV profiles. The synthetic jets were introduced through radial holes in machine casing in the location before flow separation origin. Synthetic jet actuator was designed with the use of a speaker by UT AVCR. Its membrane had diameter of 63 mm. Excitation frequency was chosen in the range of 500 Hz - 700 Hz. Synthetic jets favourably influenced separated flow on the vane profiles in the distance of (5 - 12) mm from the casing surface. The reduction of flow separation area caused in the region near the casing the decrease of the profile loss coefficient approximately by 20%.

Reduction of background noise induced by wind tunnel jet exit vanes

Science.gov (United States)

Martin, R. M.; Brooks, T. F.; Hoad, D. R.

1985-01-01

The NASA-Langley 4 x 7 m wind tunnel develops low frequency flow pulsations at certain velocity ranges during open throat mode operation, affecting the aerodynamics of the flow and degrading the resulting model test data. Triangular vanes attached to the trailing edge of flat steel rails, mounted 10 cm from the inside of the jet exit walls, have been used to reduce this effect; attention is presently given to methods used to reduce the inherent noise generation of the vanes while retaining their pulsation reduction features.

Further development and performance evaluation of the autonomous sailing boat Maribot Vane

OpenAIRE

Dhomé, Ulysse

2018-01-01

This paper describes the ongoing development of Maribot Vane, an autonomous sailing vessel at the Maritime Robotics Laboratory of KTH, the Royal Institute of Technology, Stockholm. There is an ac-celerating need for ocean sensing where autonomous vehicles can play a key role in assisting scientists with environmental monitoring and collecting oceanographic data. The purpose of Maribot Vane is to offer a sus-tainable alternative for these autonomous missions by using wind and an energy efficie...

Erosion estimation of guide vane end clearance in hydraulic turbines with sediment water flow

Science.gov (United States)

Han, Wei; Kang, Jingbo; Wang, Jie; Peng, Guoyi; Li, Lianyuan; Su, Min

2018-04-01

The end surface of guide vane or head cover is one of the most serious parts of sediment erosion for high-head hydraulic turbines. In order to investigate the relationship between erosion depth of wall surface and the characteristic parameter of erosion, an estimative method including a simplified flow model and a modificatory erosion calculative function is proposed in this paper. The flow between the end surfaces of guide vane and head cover is simplified as a clearance flow around a circular cylinder with a backward facing step. Erosion characteristic parameter of csws3 is calculated with the mixture model for multiphase flow and the renormalization group (RNG) k-𝜀 turbulence model under the actual working conditions, based on which, erosion depths of guide vane and head cover end surfaces are estimated with a modification of erosion coefficient K. The estimation results agree well with the actual situation. It is shown that the estimative method is reasonable for erosion prediction of guide vane and can provide a significant reference to determine the optimal maintenance cycle for hydraulic turbine in the future.

Acting in solidarity : Testing an extended dual pathway model of collective action by bystander group members

NARCIS (Netherlands)

Saab, Rim; Tausch, Nicole; Spears, Russell; Cheung, Wing-Yee

We examined predictors of collective action among bystander group members in solidarity with a disadvantaged group by extending the dual pathway model of collective action, which proposes one efficacy-based and one emotion-based path to collective action (Van Zomeren, Spears, Fischer, & Leach,

CFD analysis for spacer grid mixing vane design

International Nuclear Information System (INIS)

Park, Sung-Kew; Kim, Kang-Hoon; Park, Eung-Jun; Jung, Yil-Sup; Suh, Jung-Min; Jeong, Ji-Hun

2008-01-01

A computational fluid dynamics (CFD) analysis for a rod bundle with the larger scale model (6x6 array model) has been performed to develop the base shape of mixing vane in accordance with the hydraulic and thermal performance. Explanatory parameters are span pressure drop and span average heat transfer coefficient. The concern related to hot spot is also considered as a subsidiary criterion. Of the several candidates, the final candidate was determined by using the CFD analysis code, STAR-CD. And then, the optimization for it was performed using the response surface method (RSM) that the proper tolerance was considered under the two acceptance criteria such as lower span pressure drop while maintaining the span average heat transfer coefficient with respect to the current shape. The optimized mixing vane shape was verified by the CFD analysis including the effects of allowable tolerance. (author)

Background noise measurements from jet exit vanes designed to reduced flow pulsations in an open-jet wind tunnel

Science.gov (United States)

Hoad, D. R.; Martin, R. M.

1985-01-01

Many open jet wind tunnels experience pulsations of the flow which are typically characterized by periodic low frequency velocity and pressure variations. One method of reducing these fluctuations is to install vanes around the perimeter of the jet exit to protrude into the flow. Although these vanes were shown to be effective in reducing the fluctuation content, they can also increase the test section background noise level. The results of an experimental acoustic program in the Langley 4- by 7-Meter Tunnel is presented which evaluates the effect on tunnel background noise of such modifications to the jet exit nozzle. Noise levels for the baseline tunnel configuration are compared with those for three jet exit nozzle modifications, including an enhanced noise reduction configuration that minimizes the effect of the vanes on the background noise. Although the noise levels for this modified vane configuration were comparable to baseline tunnel background noise levels in this facility, installation of these modified vanes in an acoustic tunnel may be of concern because the noise levels for the vanes could be well above background noise levels in a quiet facility.

''VaneCAM'' - the third generation of camshaft adjustment systems; ''VaneCAM'' - Nockenwellenversteller der dritten Generation

Energy Technology Data Exchange (ETDEWEB)

Knecht, A. [Hydraulik-Ring GmbH, Nuertingen (Germany). Entwicklung Motorentechnik; Stephan, W. [Hydraulik-Ring GmbH, Nuertingen (Germany); Hannibal, W. [Fachhochschule Suedwestfalen, Iserlohn (Germany). Labor fuer Konstruktion und CAE-Anwendungen

2002-04-01

Continuously variable camphasers are now well established for modern spark-ignition engines in high-volume production. With the latest generation of camshaft adjustment systems using the vane-type actuator principle, it is possible to move rapidly and reliably through a large adjustment angle. The layout of these adjusting systems is very simple. The production costs are low in comparison to the first generation of camphasers using spur/helical gears to vary the valve timing. The new-generation systems are mechatronic, with the function depending on the coordination and tuning of hydraulic actuation and engine electronics. The term 'VaneCAM' is used for the continuously variable systems of this new generation supplied by Hydraulik-Ring in Nuertingen, Germany. (orig.) [German] Stufenlos wirkende Nockenwellenversteller haben sich an modernen Ottomotoren in den letzten Jahren in der Grossserie etabliert. Mit der neuesten Generation von Nockenwellenverstellern, die nach dem Schwenkmotor-Prinzip aufgebaut sind, lassen sich grosse Verdrehwinkel sehr schnell und betriebssicher verstellen. Der Aufbau dieser Versteller ist einfach, und die Herstellkosten sind gering im Vergleich zur ersten Generation von Verstellern. Bei den Systemen der neuen Generation handelt es sich um mechatronische Systeme, deren Funktion von dem Zusammenspiel und der Abstimmung von hydraulischer Ansteuerung und Motorelektronik abhaengt. Mit dem Begriff 'VaneCAM' werden die stufenlos wirkenden Systeme dieser neuen Generation von Hydraulik-Ring aus Nuertingen bezeichnet. (orig.)

Static pressure recovery analysis in the vane island diffuser of a centrifugal pump

Energy Technology Data Exchange (ETDEWEB)

Si, Qiaorui [National Research Center of Pumps, Jiangsu University, Zhenjiang (China); Dupont, Patrick; Bayeul-Laine, Annie-Claude; Dazin, Antoine; Roussette, Olivier; Bois, Gerard [LML, UMR CNRS 8107 Ecole Centrale de Lille, Lille (France)

2016-02-15

The overall performance of a vane-island type diffuser of a centrifugal pump model was obtained by means of directional probe traverses. These measurements were performed in an air model of a real hydraulic pump for five volume flow rates. Directional probe traverses are performed with a classical three-hole probe to cover most of the complete inlet section of the diffuser from hub to shroud and from pressure to suction side. Existing Particle image velocimetry (PIV) measurement results are also used to compare probe measurement results between the inlet and outlet throats of vane island diffuser at mid-span. Some assistance from already existing unsteady calculation, including leakage effects, is used to evaluate the numerical approach capability and to correctly define the mean initial conditions at impeller's outlet section. Pressure recovery and the measured total pressure loss levels inside this particular vane diffuser geometry are then calculated. Detailed analysis of the flow structure at the inlet section of the vane island diffuser is presented to focus on pressure evolution inside the entire diffuser section for different flow rates. The combined effects of incidence angle and blockage distributions along hub to shroud direction are found to play an important role on loss distribution in such a diffuser.

A novel thermally driven rotor-vane/pressure-exchange ejector refrigeration system with environmental benefits and energy efficiency

International Nuclear Information System (INIS)

Hong, W.J.; Alhussan, Khaled; Zhang Hongfang; Garris, Charles A.

2004-01-01

The latest results of an ongoing coordinated experimental and computational program on the design and performance of a novel supersonic rotor-vane/pressure-exchange ejector for thermally driven ejector refrigeration systems are presented. For the supersonic rotor-vane/pressure-exchange ejector, careful management of the entropy rise through the oblique shocks and boundary layers is required for obtaining an advance in ejector performance. Since the invention of this new ejector is quite recent, understanding its aerodynamics, with the consequent optimization of performance, is in the formative stage. This paper shows how the supersonic aerodynamics is managed to provide the desirable flow induction characteristics through computational study and, in parallel, experimental results including flow visualization showing actual behavior with different-shaped rotor vanes. The importance of the existence of the tail part with a long expansion ramp, the sharp leading edge such as knife-edge, the proper height of leading edges, for the overall shape of rotor vane, were observed. Also the larger spin-angle rotor vane produces better flow induction and mixing between primary flow and secondary flow

Assessment of guide vane self-excitation stability at small openings in pump flow

International Nuclear Information System (INIS)

Nennemann, B; Sallaberger, M; Henggeler, U; Gentner, C; Parkinson, E

2012-01-01

A parameter study of self-excited pump turbine guide vane instability at small openings using a combined CFD-1DOF approach shows that clear tendencies are difficult to obtain. Two types of boundary conditions can be used in the simulations: prescribed mass flow and prescribed pressure. Simulations with both show results that - for one specific operating condition - are consistent with a self-excited guide vane incident at a prototype pump turbine. However, over a larger range of reduced velocities, the tendencies obtained with the two boundary condition types are not always consistent. Pressure boundary conditions may be the more realistic option. Results then show that with increasing reduced velocity, guide vanes will eventually reach static instability or divergence. This may not be problematic. In contrast, passing through a zone of dynamic instability during operation should and can be avoided.

Test procedure for use of the shear vane in tanks 103-SY, 103-AN, and 103-AW

International Nuclear Information System (INIS)

LeClair, M.D.; Waters, E.

1995-01-01

This is a record copy of a test procedure for application of the full-scale shear vane to underground waste tanks at Hanford. The introduction of the report provides background information on the development and proof-testing of the shear vane, as well as information about its current location. The document was originally prepared in 1988, and the work as shelved temporarily for lack of funds. Activities to utilize the shear vane will be expedited by use of this information

Velocity and pressure measurements in guide vane clearance gap of a low specific speed Francis turbine

Science.gov (United States)

Thapa, B. S.; Dahlhaug, O. G.; Thapa, B.

2016-11-01

In Francis turbine, a small clearance gap between the guide vanes and the cover plates is usually required to pivot guide vanes as a part of governing system. Deflection of cover plates and erosion of mating surfaces causes this gap to increase from its design value. The clearance gap induces the secondary flow in the distributor system. This effects the main flow at the runner inlet, which causes losses in efficiency and instability. A guide vane cascade of a low specific speed Francis turbine has been developed for experimental investigations. The test setup is able to produce similar velocity distributions at the runner inlet as that of a reference prototype turbine. The setup is designed for particle image velocimetry (PIV) measurements from the position of stay vane outlet to the position of runner inlet. In this study, velocity and pressure measurements are conducted with 2 mm clearance gap on one side of guide vane. Leakage flow is observed and measured together with pressure measurements. It is concluded that the leakage flow behaves as a jet and mixes with the main flow in cross-wise direction and forms a vortex filament. This causes non-uniform inlet flow conditions at runner blades.

Enlarging the operation range of a centrifugal compressor by cutting vanes based on CFD

International Nuclear Information System (INIS)

Mo, J T; Pan, X H; Gu, C H; Zheng, S Y

2013-01-01

Many centrifugal compressors are liable to insufficient operation range. The purpose of this paper is to enlarge the operation range of a centrifugal compressor used in turbocharger by cutting vanes. Some numerical works have been done based on CFD. The comparison of the calculated and measured results shows good agreement. The overall performance characteristics of the centrifugal compressor with different cutted vanes are observed and analyzed. The performance characteristic curves show that cutting vanes can increase the operation range by more than 50% with the loss of the highest efficiency limited in 1%. The flow fields are also shown in this paper and related explanations about the change of the performance characteristics curves are given. Shock wave is also detected in the simulation, and some related characteristics are summed up

Preliminary Investigation on Turbulent Flow in Tight-lattice Rod Bundle with Twist-mixing Vane Spacer Grid

International Nuclear Information System (INIS)

Lee, Chiyoung; Kwack, Youngkyun; Park, Juyong; Shin, Changhwan; In, Wangkee

2013-01-01

Our research group has investigated the effect of P/D difference on the behavior of turbulent rod bundle flow without the mixing vane spacer grid, using PIV (Particle Image Velocimetry) and MIR (Matching Index of Refraction) techniques for tight lattice fuel rod bundle application. In this work, using the tight-lattice rod bundle with a twist-mixing vane spacer grid, the turbulent rod bundle flow is preliminarily examined to validate the PIV measurement and CFD (Computational Fluid Dynamics) simulation. The turbulent flow in the tight-lattice rod bundle with a twist-mixing vane spacer grid was preliminarily examined to validate the PIV measurement and CFD simulation. Both were in agreement with each other within a reasonable degree of accuracy. Using PIV measurement and CFD simulation tested in this work, the detailed investigations on the behavior of turbulent rod bundle flow with the twist-mixing vane spacer grid will be performed at various conditions, and reported in the near future

One member, two leaders: extending leader-member exchange theory to a dual leadership context.

Science.gov (United States)

Vidyarthi, Prajya R; Erdogan, Berrin; Anand, Smriti; Liden, Robert C; Chaudhry, Anjali

2014-05-01

In this study, we develop and test a model that extends leader-member exchange (LMX) theory to a dual leadership context. Drawing upon relative deprivation theory, we assert that when employees work for 2 leaders, each relationship exists within the context of the other relationship. Thus, the level of alignment or misalignment between the 2 relationships has implications for employees' job satisfaction and voluntary turnover. Employing polynomial regression on time-lagged data gathered from 159 information technology consultants nested in 26 client projects, we found that employee outcomes are affected by the quality of the relationship with both agency and client leaders, such that the degree of alignment between the 2 LMXs explained variance in outcomes beyond that explained by both LMXs. Results also revealed that a lack of alignment in the 2 LMXs led to asymmetric effects on outcomes, such that the relationship with agency leader mattered more than the relationship with one's client leader. Finally, frequency of communication with the agency leader determined the degree to which agency LMX affected job satisfaction in the low client LMX condition. (c) 2014 APA, all rights reserved.

Improvement of wells turbine performance by means of 3D guide vanes; Sanjigen annai hane ni yoru wells turbine seino no kaizen

Energy Technology Data Exchange (ETDEWEB)

Takao, M.; Kim, T.H. [Saga University, Saga (Japan); Setoguchi, T. [Saga University, Saga (Japan). Faculty of Science and Engineering; Inoue, M. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

2000-02-25

Performance of a Wells turbine was improved by equipping 3D guide vanes before and behind a rotor. For further improvement, 3D guide vanes have been proposed in this paper. The performance of the Wells turbine with 2D and 3D guide vanes have been investigated experimentally by model testing under steady flow conditions. Then, the running and starting characteristics in irregular ocean waves have been obtained by a computer simulation. As a result, it is found that both of the running and starting characteristics of the Wells turbine with 3D guide vanes are superior to those of the turbine with 2D guide vanes. (author)

The effect of grid assembly mixing vanes on critical heat flux values and azimuthal location in fuel assemblies

International Nuclear Information System (INIS)

De Crecy, F.

1994-01-01

Critical heat flux (CHF) is one of the limiting phenomena for a PWR. It has been widely studied for years, but many facts are still not satisfactorily understood. This paper deals with the effect of the grid assembly mixing vanes on both the value of the CHF and the azimuthal location of the departure from nucleate boiling (DNB). A series of experimental studies was performed on electrically heated, 5x5 square pitched, vertical rod bundles. Two specific grid assembly designs were used: with and without mixing vanes. DNB was detected by eight thermocouples welded internally in each rod at the same level in order to determine the azimuthal location. The coolant was Freon-12 flowing upwards to simulate high pressure water (as defined by Stevens). Single-phase flow experiments were also conducted to measure the exit temperature field in order to obtain the mixing coefficients for subchannel analysis.The results show very clearly that the mixing vanes have a significant effect on both the DNB azimuthal location and the CHF value. - Without mixing vanes, DNB occurs mainly on the most central rod and preferentially at the azimuthal location facing the adjacent rod. - With mixing vanes, DNB can occur on any of the nine central rods and is distributed in an apparently random way around the rod. -The effect of the mixing vanes on CHF is dramatic and depends a great deal on the parameter range (pressure, local mass velocity and local quality). Generally speaking, CHF with mixing vanes is significantly higher than without mixing vanes, but this effect can be inverted in some cases.In order to understand this fact more clearly, it is necessary to perform detailed analysis of subchannel behavior. Indeed, the analyses show that the magnitude of this effect is closely related to the mixing coefficients used. These mixing coefficients, estimated from the single-phase flow experiments, are subject to large uncertainties in two-phase flow. ((orig.))

Experimental investigation of in-cylinder air flow to optimize number of helical guide vanes to enhance DI diesel engine performance using mamey sapote biodiesel

Science.gov (United States)

Kumar, A. Raj; Janardhana Raju, G.; Hemachandra Reddy, K.

2018-03-01

The current research work investigates the influence of helical guide vanes in to the intake runner of a D.I diesel engine operating by the high viscous Mamey Sapote biodiesel to enhance in-cylinder suction air flow features. Helical guide vanes of different number of vanes are produced from 3D printing and placed in the intake manifold to examine the air flow characteristics. Four different helical guide vane devices namely 3, 4, 5 and 6 vanes of the same dimensions are tested in a D.I diesel engine operating with Mamey Sapote biodiesel blend. As per the experimental results of engine performance and emission characteristics, it is found that 5 vanes helical guide vane swirl device exhibited in addition number of increased improvements such as the brake power and bake thermal efficiency by 2.4% and 8.63% respectively and the HC, NOx, Carbon monoxide and, Smoke densities are reduced by 15.62%, 4.23%, 14.27% and 9.6% at peak load operating conditions as collate with normal engine at the same load. Hence this investigation concluded that Helical Guide Vane Devices successfully enhanced the in-cylinder air flow to improve better addition of Mamey Sapote biodiesel with air leading in better performance of the engine than without vanes.

The effect of mixing-vane arrangements in a subchannel turbulent flow

International Nuclear Information System (INIS)

Ikeno, Tsutomu; Murata, Tamotsu; Kajishima, Takeo

2006-01-01

Large eddy simulation (LES) of developed turbulent flows in a rod bundle was carried out for four spacer designs. The mixing-vanes attached at the spacer were inclined at 30degC or 20deg; they were arranged to promote the swirling or convective flow. These arrangements are possible elements to compose an actual rod bundle. Our LES technique with a consistent higher-order immersed boundary method and a one-equation dynamic sub-grid scale model contributed to an efficient treatment of the complex wall configurations of rods and spacers. The computational results reasonably reproduced experimental results for the drag coefficient and the decay rate of swirling flow. The profiles of the axial velocities and the turbulence intensities indicated reasonable trend for the turbulent flow in the rod bundle. The effect of mixing-vane arrangement on the lateral flows was successfully clarified: the cross flow took the longer way on the rod surface than the swirling flow and then was more significantly influenced by momentum diffusion at the no-slip wall. Therefore, the largely inclined mixing-vanes promoted the cross flow only in the neighborhood of the spacer, the swirling flow inside a subchannel could reach farther downstream than the cross flow. (author)

Performance and internal flow characteristics of a cross-flow turbine by guide vane angle

International Nuclear Information System (INIS)

Chen, Z M; Choi, Y D

2013-01-01

This study attempts to investigate the performance and internal flow characteristics of a cross-flow turbine by guide vane angle. In order to improve the performance of a cross flow turbine, the paper presents a numerical investigation of the turbine with air supply and discusses the influence of variable guide vane angle on the internal flow. A newly developed air supply from air suction Hole is adopted. To investigate the performance and internal flow of the cross-flow turbine, the CFD software based on the two-phase flow model is utilized. The numerical grids are made in two-dimensional geometry in order to shorten the time of two-phase calculations. Then a series of CFD analysis has been conducted in the range of different guide vane angle. Moreover, local output power is divided at different stages and the effect of air layer in each stage is examined

Introduction on KPS's maintenance experience of the swirl vane assemblies of primary separators for SG model F in Korea

International Nuclear Information System (INIS)

Kim, Yong tae

2003-01-01

Recently, we had experienced to replace the Swirl Vane Assemblies of primary moisture separator for SG model F in Korea because of serious degradation (Thinning) in carbon steel swirl vane blades and carbon steel separator barrel wall adjacent to swirl vane blades. When the symptom was observed by us at the first time on the swirl vane assemblies, there were small or a bit clear erosion / or corrosion marks on the edge regions of the blades but within 3 cycles of operation, we found that those marks became holes which penetrated the most of swirl vane assemblies and even more seriously, some parts of the assemblies were worn-out. Therefore, we concluded that the speed of degradation would be very rapid and serious from the beginning stage. It had been assumed that these kinds of thinning problems would be due to FAC(Flow Accelerated Corrosion) because the plants having these problems are using a highly concentrated hydrazine for the water treatment of secondary side which lead to reduce the oxygen and pH in the water. What are more serious reasons will be that the swirl vane assemblies are very weak to FAC because they were made by a low concentrated chromium carbon steel and the assemblies would have to be under the operation conditions of the highly turbulent steam-water mixed fluid with the operating temperature of higher than 280 .deg. C. Potentially, the damaged swirl vane assemblies of the primary moisture separator may create bad influences for the plant operation because it may cause the rupture of SG Tubes and over-exceed fluid influx onto the turbine and etc. KPS had successfully performed the replacement of the degraded swirl vane assemblies through our own planning and preparation. This was the unique case in all over the world and I would like to introduce you about our unique repair experience to prepare an expected future situation as we see the similar problems in other model F SGs operating in Korea

Performance Analysis of a Centrifugal Compressor for HFC-134a with aviation of Diffuser Vane Angle

International Nuclear Information System (INIS)

Park, Han Young; Chung, Jin Taek; Shin, You Hwan; Lee, Yoon Pyo; Kim, Kwang Ho; Cho, Yong Hun; Kim, Jong Seong

2007-01-01

Numerical simulation on the two-stage centrifugal compressor with Low Solidity Vaned Diffuser (LSVD) for HFC-134a turbo-chiller was performed using a commercial code. The comparative study with experimental results from other compressor was also investigated to testify the simulation schemes. The numerical analysis was separately simulated for each stage of the compressor and the effect of impeller-diffuser flow interaction was considered. Setting angle of the diffuser vane changed in the range of 15 .deg. and the effects on its variation were discussed in detail including the flow analysis in the passage of the compressor. The vane setting angle obtained from the preliminary design was slightly adjusted to the optimal value by the performance enhancement in terms of pressure recovery and flow characteristics

Numerical Study of Bubble Coalescence and Breakup in the Reactor Fuel Channel with a Vaned Grid

Directory of Open Access Journals (Sweden)

Tenglong Cong

2018-01-01

Full Text Available The characteristics of bubbles of different sizes in fuel assembly are vital to two-phase flow resistance and heat transfer capacity. However, due to the swirl flow caused by the mixing vane, bubbles can crowd at the heated surface, which may anticipate the occurrence of departure from nucleation boiling. In the current work, the adiabatic two-phase flow in a simplified fuel assembly was analyzed by using the Eulerian two-fluid model and the MUSIG (MUltiple SIze Group model. This computational domain consists of two coolant channels and two sets of vaned spacers, with three sets of periodic boundary conditions at the side faces of the domain. The distributions of vapor phase and bubble diameters were obtained, based on which the effects of mixing vanes on the bubble characteristics were analyzed. Vapor phase crowded at the rod surface in the higher inlet vapor fraction case, but crowded in the channel center in the lower inlet vapor fraction cases. This work can be used as a reference for the design of mixing vanes to avoid the anticipation of departure of nucleation boiling that may be caused by unreasonable design.

Computational model for turbulent flow around a grid spacer with mixing vane

International Nuclear Information System (INIS)

Tsutomu Ikeno; Takeo Kajishima

2005-01-01

Turbulent mixing coefficient and pressure drop are important factors in subchannel analysis to predict onset of DNB. However, universal correlations are difficult since these factors are significantly affected by the geometry of subchannel and a grid spacer with mixing vane. Therefore, we propose a computational model to estimate these factors. Computational model: To represent the effect of geometry of grid spacer in computational model, we applied a large eddy simulation (LES) technique in couple with an improved immersed-boundary method. In our previous work (Ikeno, et al., NURETH-10), detailed properties of turbulence in subchannel were successfully investigated by developing the immersed boundary method in LES. In this study, additional improvements are given: new one-equation dynamic sub-grid scale (SGS) model is introduced to account for the complex geometry without any artificial modification; the higher order accuracy is maintained by consistent treatment for boundary conditions for velocity and pressure. NUMERICAL TEST AND DISCUSSION: Turbulent mixing coefficient and pressure drop are affected strongly by the arrangement and inclination of mixing vane. Therefore, computations are carried out for each of convolute and periodic arrangements, and for each of 30 degree and 20 degree inclinations. The difference in turbulent mixing coefficient due to these factors is reasonably predicted by our method. (An example of this numerical test is shown in Fig. 1.) Turbulent flow of the problem includes unsteady separation behind the mixing vane and vortex shedding in downstream. Anisotropic distribution of turbulent stress is also appeared in rod gap. Therefore, our computational model has advantage for assessing the influence of arrangement and inclination of mixing vane. By coarser computational mesh, one can screen several candidates for spacer design. Then, by finer mesh, more quantitative analysis is possible. By such a scheme, we believe this method is useful

the screw-conveyor vane design for piece-wise construction

African Journals Online (AJOL)

Dr Obe

Summary. One of the long-used methods of conveying granular, Powdery or slurry material is by the screw conveyor. This method of transport is well suited to some at the needs of local processing Industries based on such local produce as millet, maize, cocoa-beans, rice, palm-kernels. The spiral vanes of such conveyors ...

A Three-Dimensional Coupled Internal/External Simulation of a Film-Cooled Turbine Vane

Science.gov (United States)

Heidmann, James D.; Rigby, David L.; Ameri, Ali A.

1999-01-01

A three-dimensional Navier-Stokes simulation has been performed for a realistic film-cooled turbine vane using the LeRC-HT code. The simulation includes the flow regions inside the coolant plena and film cooling holes in addition to the external flow. The vane is the subject of an upcoming NASA Glenn Research Center experiment and has both circular cross-section and shaped film cooling holes. This complex geometry is modeled using a multi-block grid which accurately discretizes the actual vane geometry including shaped holes. The simulation matches operating conditions for the planned experiment and assumes periodicity in the spanwise direction on the scale of one pitch of the film cooling hole pattern. Two computations were performed for different isothermal wall temperatures, allowing independent determination of heat transfer coefficients and film effectiveness values. The results indicate separate localized regions of high heat transfer coefficient values, while the shaped holes provide a reduction in heat flux through both parameters. Hole exit data indicate rather simple skewed profiles for the round holes, but complex profiles for the shaped holes with mass fluxes skewed strongly toward their leading edges.

Measuring Undrained Shear Strength using CPT and Field Vane

DEFF Research Database (Denmark)

Luke, Kirsten

1992-01-01

This paper presents the results of CPT's and Field Vane tests from two small test areas with different soils, Glacial Till and Yoldia Clay. An average of Nk = qt/cv for the Yoldia Clay is 7.7 with a standard deviation of 0.7. The average of Nk for the Glacial Till is 9.7 with a standard deviation...

T2-weighted liver MRI using the multiVane technique at 3T: Comparison with conventional T2-weighted MRI

Energy Technology Data Exchange (ETDEWEB)

Kang, Kyung A [Dept. of Radiology, Myongji Hospital, Seonam University College of Medicine, Goyang (Korea, Republic of); Kim, Young Kon; Jeong, Woo Kyoung; Choi, Dong Il; Lee, Won Jae [Dept. of Radiology and Center for Imaging Science, Samsung Medical Center, Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of); Kim, Eun Ju [Philips Healthcare Korea, Philips, Seoul (Korea, Republic of); Jung, Sin Ho; Baek, Sun Young [Biostatistics and Clinical Epidemiology Center, Samsung Medical Center, Seoul (Korea, Republic of)

2015-10-15

To assess the value of applying MultiVane to liver T2-weighted imaging (T2WI) compared with conventional T2WIs with emphasis on detection of focal liver lesions. Seventy-eight patients (43 men and 35 women) with 86 hepatic lesions and 20 pancreatico-biliary diseases underwent MRI including T2WIs acquired using breath-hold (BH), respiratory-triggered (RT), and MultiVane technique at 3T. Two reviewers evaluated each T2WI with respect to artefacts, organ sharpness, and conspicuity of intrahepatic vessels, hilar duct, and main lesion using five-point scales, and made pairwise comparisons between T2WI sequences for these categories. Diagnostic accuracy (Az) and sensitivity for hepatic lesion detection were evaluated using alternative free-response receiver operating characteristic analysis. MultiVane T2WI was significantly better than BH-T2WI or RT-T2WI for organ sharpness and conspicuity of intrahepatic vessels and main lesion in both separate reviews and pairwise comparisons (p < 0.001). With regard to motion artefacts, MultiVane T2WI or BH-T2WI was better than RT-T2WI (p < 0.001). Conspicuity of hilar duct was better with BH-T2WI than with MultiVane T2WI (p = 0.030) or RT-T2WI (p < 0.001). For detection of 86 hepatic lesions, sensitivity (mean, 97.7%) of MultiVane T2WI was significantly higher than that of BH-T2WI (mean, 89.5%) (p = 0.008) or RT-T2WI (mean, 84.9%) (p = 0.001). Applying the MultiVane technique to T2WI of the liver is a promising approach to improving image quality that results in increased detection of focal liver lesions compared with conventional T2WI.

Investigating the thermal hydraulic performance of spacer grid with mixing vanes using STAR-CCM+ and MATRA

International Nuclear Information System (INIS)

Agbodemegbe, V. Y.

2014-07-01

Enhancement of heat transfer for flow through rod bundles is linked to the extent and sustainability of mixing in the flow geometry. Spacer grids used as support for rod bundles in nuclear reactors, when attached with ditferent designs of mixing vanes promote turbulent mixing by inducing swirl or forced lateral convection that improves mixing within or between sub-channels. The improved turbulent mixing raises the margin of the onset of critical heat flux in light water reactors (LWR) and also ensures a higher fuel cycle economy. To optimize design of mixing vanes and performance of spacer grids with mixing vanes, computational fluid dynamic simulations arc carried out on new designs and validated experimentally prior to industrial application. In the present study, computational fluid dynamic simulation using STAR-CCM+ and sub-channel analysis with MATRA were performed for flow of water through a 5 X 5 rod bundle geometry for which the rod to rod pitch to diameter ratio was 1.33 and the wall to rod pitch to diameter ratio was 0.74. The two layer k-epsilon turbulence model with an all- y + automatic wall treatment function in STAR-CCM+ were adopted for an isothermal single phase flow through the geometry with imposed cyclic periodic and non-cyclic periodic interface boundary conditions. The objective was to primarily investigate the detail flow behavior in rod bundle in the presence of spacer grids with and without attached mixing vanes. Furthermore, the present study also investigated the extent of turbulent mixing and lateral mass flux induced by the mixing vanes through comparative analysis of parametric trends for spacer grid with and without mixing vanes. New models and empirical correlations for describing the mixing vanes effects were also developed. These semi-empirical correlations improved the prediction for lateral mass flux due to turbulence, fraction of flow diverted through gaps and cross-flow resistance coefficients. Validation of simulation results

Heat transfer coefficient testing in nuclear fuel rod bundles with mixing vane grids

International Nuclear Information System (INIS)

Conner, Michael E.; Smith, L. David III; Holloway, Mary V.; Beasley, Donald E.

2005-01-01

An air heat transfer test facility was developed to test the heat transfer downstream of support grids in simulated PWR nuclear fuel rod bundles. The goal of this testing is to study the single-phase heat transfer coefficients downstream of grids with mixing vanes in a square-pitch rod bundle. The technique developed utilizes fully-heated grid spans and a specially designed thermocouple holder that can be moved axially down the rod bundle and aximuthally within a test rod. From this testing, the axial and aximuthally varying heat transfer coefficient can be determined. Different grid designs are tested and compared to determine the heat transfer enhancement associated with key grid features such as mixing vanes. (author)

CFD analysis of supercritical water flow and heat transfer in single channel with mixing vane

International Nuclear Information System (INIS)

Zuo Guoping; Xie Hongyan; Yu Tao

2012-01-01

Three-dimensional rectangular channel with the mixing wane in supercritical water reactor is investigated with CFX. The mixing vane elevation influenced on temperature distribution and flow field are simulated in the model. The results showed the mixing vane cause fluid circumferential flow, making flow hot and cold fluids mixed and fluid temperature uniform distribution, effectively improve the fuel rod surface temperature distribution and reduced hot temperature. Among the mixing wing elevation of 15, 30, 45, 50, 60 and 70 angle, the 30 angle is the best case in improving temperature distribution. (authors)

RF field measurement of a four-vane type RFQ with PISLs

International Nuclear Information System (INIS)

Ueno, A.; Yamajaki, Y.

1992-01-01

Field instability due to a dipole mode mixing is the most significant disadvantage of an original four-vane type radio-frequency quadrupole (RFQ) linac. In order to avoid any dipole mode mixing, several pairs of vane coupling rings (VCRs) have mainly been used so far. However the VCR has complicated shape and is difficult to fabricate, particularly in the RFQ linac operated with a high-duty factor. Thus, a new field-stabilization concept was proposed and was referred to as a π-mode stabilizing loop (PISL) in a previous paper. The results of rf characteristics measurements on a low-power model cavity with or without PISLs are presented in this paper. The measurements showed that the PISLs were capable of stabilizing the accelerating mode, reducing the ratio of a dipole mode mixing from 7% to less than 1.5% (Author) 4 figs., tab., 10 refs

Performance Enhancement of the In-Line Fan Equipped with the Guiding Vane and the Tail Body

Directory of Open Access Journals (Sweden)

Hung-Cheng Yen

2014-02-01

Full Text Available This integrated numerical and experimental study intends to enhance the performance of an in-line fan with the implement of the guiding vane and the tail body. At first the flow flied associated with the original in-line fan is simulated and analyzed within the framework of CFD code Fluent, in which the finite volume method is applied. Next, the guiding vane is constructed based on the calculated flow characteristics, and attached in the downstream of rotor to smoothen the flow pattern. An appropriate guiding vane with high-performance and low-noise features can be achieved after several design iterations. In addition, the tail body connected to the motor is introduced for further enhancing the fan performance by reducing the sizes of wake and reversed flow behind the hub. Thereafter, to manufacture the mockup for experimental verification, the modified fan with guiding vane is plotted in the CAD/CAM format for mockup fabrication via the rapid-prototype technique. Moreover, a set of relations correlating the performance and noise of this fan prototype are executed inside AMCA test chamber and semianechoic chamber, respectively. Consequently, the feasibility of design scheme and numerical system can be verified according to these experimental results. In summary, this work provides a systematic scheme for designing and analyzing the in-line fan.

The VanE operon in Enterococcus faecalis N00-410 is found on a putative integrative and conjugative element, Tn6202.

Science.gov (United States)

Boyd, D A; Mulvey, M R

2013-02-01

To date no complete genetic structure of acquired DNA harbouring a d-Ala-d-Ser operon in an Enterococcus is known. We wished to characterize the acquired DNA harbouring the vanE operon located in the Enterococcus faecalis N00-410 chromosome. Whole genome sequencing of E. faecalis N00-410 was conducted by massively parallel sequencing. Two sequence contigs harbouring the vanE region were linked by PCR and the acquired DNA harbouring the vanE operon was completely characterized. Excision/integration of the region was determined by PCR and transfer attempted by conjugation. The regions flanking the vanE operon were analysed and a total of 42 open reading frames were identified in a region flanked by inverted terminal and direct repeats (Tn6202). Tn6202 could be excised from the chromosome, circularized and the target site rejoined, but transfer could not be demonstrated. The vanE operon was found on the putative integrative and conjugative element Tn6202 in the E. faecalis N00-410 chromosome. This represents the first characterization of acquired DNA harbouring a D-Ala-D-Ser operon.

Numerical investigation of variable inlet guide vanes with trailing-edge dual slots to decrease the aerodynamic load on centrifugal compressor impeller

Directory of Open Access Journals (Sweden)

Jianchi Xin

2016-03-01

Full Text Available In engineering practice, most centrifugal compressors use variable inlet guide vanes which can provide pre-whirl and control volume flow rates. As the impeller of a centrifugal compressor passes through the wakes created from the guide vanes, the aerodynamic parameters change significantly. The concept of adding dual slots at the trailing-edge of the guide vanes is proposed for reducing the aerodynamic load on the compressor impeller blades. In this article, the steady and unsteady performances of the new guide vanes are analysed under two compressor operating conditions (winter and design conditions. The results show that the average amplitude of the impeller passing frequency at the leading edge has a 13% decrease under the winter condition, especially at the middle and root parts. Moreover, the dual slots structure has no effect on the overall compressor performance.

Numerical study of pressure fluctuations in different guide vanes' opening angle in pump mode of a pump turbine

International Nuclear Information System (INIS)

Sun, Y K; Zuo, Z G; Liu, S H; Wu, Y L; Liu, J T

2012-01-01

A numerical model based on a pumped storage power station was built to develop the numerical simulation, to analyze the pressure fluctuations in a pump turbine in different guide vanes' opening angle. The different guide vanes' opening angles were simulated using the SST k-ω turbulence model and SIMPLEC Pressure-Velocity coupling scheme. The pressure sensor were placed in mainly three positions, they are: bottom ring between runner and the wicket gates, downstream and left side in the draft tube cone below the runner. All the peak to peak values of pressure fluctuation meet signal probability of 97%. The frequency is gained by Fast Fourier Transform. The pressure fluctuations in different positions of the model in pump condition were showed when the guide vanes' opening angels were different. The simulation results confirmed the results gained in model tests. The results show that pressure fluctuations in design opening angle were much lower than those in off design opening angle. The main source of pressure fluctuations between runner and guide vanes is rotor stator interaction. While a lower frequency is the main frequency of the pressure fluctuation in draft tube.

Suction Side Roughness Effects on Film Cooling Heat Transfer on a Turbine Vane

National Research Council Canada - National Science Library

Rutledge, James

2004-01-01

An experimental study was conducted in a simulated three vane linear cascade to determine the effects of surface roughness and film cooling on the heat transfer coefficient distribution in the region...

Analytical solution for the electrical properties of a radio-frequency quadrupole (RFQ) with simple vanes

International Nuclear Information System (INIS)

Lancaster, H.

1982-01-01

Although the SUPERFISH program is used for calculating the design parameters of an RFQ structure with complex vanes, an analytical solution for electrical properties of an RFQ with simple vanes provides insight into the parametric behavior of these more complicated resonators. The fields in an inclined plane wave guide with proper boundary conditions match those in one quadrant of an RFQ. The principle of duality is used to exploit the solutions to a radial transmission line in solving the field equations. Calculated are the frequency equation, frequency sensitivity factors, electric field, magnetic field, stored energy (U), power dissipation, and quality factor

Numerical research on the effects of impeller pump-out vanes on axial force in a solid-liquid screw centrifugal pump

International Nuclear Information System (INIS)

Cheng, X R; Li, R N; Gao, Y; Guo, W L

2013-01-01

A commercial CFD code has been used to predict the performance of a screw centrifugal pump with pump-out vanes, especially when changing regularity of impeller axial force based on the solid-liquid two-phase flow. The Unsteady Reynolds Averaged Navier-Stokes (URANS) approach has been applied to solve the unsteady, incompressible, three-dimensional turbulent. The SIMPLEC algorithm, standard wall functions and mix two-phase flow model were applied. The RNG k ε-model was used to account the turbulence effects. By changing the number of impeller pump-out vanes and width, six different screw centrifugal pump numerical simulation projects were given, and each scheme in the different solid volume fraction were calculated respectively. The change rules of axial force, velocity and pressure distribution of flow field were obtained on the different condition and different volume fraction. The results showed that the axial forces values based solid-fluid two-phase greater than based single-phase clear water, but both changing regularity of the axial force were consistent; as same condition, the same solid-phase volume concentration, with the increase of pump-out vanes number or width, the impeller axial force increased as well. Meanwhile the number of the pump-out vanes and the width of pump-out vanes in balancing the impeller axial force, there are the most optimal value

Investigation of Blade-row Flow Distributions in Axial-flow-compressor Stage Consisting of Guide Vanes and Rotor-blade Row

Science.gov (United States)

Mahoney, John J; Dugan, Paul D; Budinger, Raymond E; Goelzer, H Fred

1950-01-01

A 30-inch tip-diameter axial-flow compressor stage was investigated with and without rotor to determine individual blade-row performance, interblade-row effects, and outer-wall boundary-layer conditions. Velocity gradients at guide-vane outlet without rotor approximated design assumptions, when the measured variation of leaving angle was considered. With rotor in operation, Mach number and rotor-blade effects changed flow distribution leaving guide vanes and invalidated design assumption of radial equilibrium. Rotor-blade performance correlated interpolated two-dimensional results within 2 degrees, although tip stall was indicated in experimental and not two-dimensional results. Boundary-displacement thickness was less than 1.0 and 1.5 percent of passage height after guide vanes and after rotor, respectively, but increased rapidly after rotor when tip stall occurred.

Effect of long time service exposure on microstructure and mechanical properties of gas turbine vanes made of IN939 alloy

International Nuclear Information System (INIS)

Jahangiri, M.R.; Abedini, M.

2014-01-01

Highlights: • Microstructure of service-exposed turbine vanes made of IN939 was investigated. • Mechanical properties of service-exposed alloy were also investigated. • Formation of M 23 C 6 films on GBs and degeneration of MCs are microstructural changes. • Despite its thermodynamic favorability, σ phase is not observed in microstructure. • Microstructural changes lead to a loss in tensile ductility and creep life. - Abstract: In the present study, the effects of long-term service exposure have been investigated on microstructure and mechanical properties of gas turbine vanes made of IN939 superalloy. The major microstructural changes for the investigated service-exposed vanes include the formation of continuous grain boundary carbides and the transformation (degeneration) of MC carbides located at the grain boundaries. The brittle σ phase, which is predicted to be stable on the basis of thermodynamic calculations, is not observed in the microstructure of service-exposed vanes. The microstructural changes during service lead to a loss in room temperature ductility as well as in creep properties of the alloy

Analysis of waves in the plasma guided by a periodical vane-type slow wave structure

International Nuclear Information System (INIS)

Wu, T.J.; Kou, C.S.

2005-01-01

In this study, the dispersion relation has been derived to characterize the propagation of the waves in the plasma guided by a periodical vane-type slow wave structure. The plasma is confined by a quartz plate. Results indicate that there are two different waves in this structure. One is the plasma mode that originates from the plasma surface wave propagating along the interface between the plasma and the quartz plate, and the other is the guide mode that originally travels along the vane-type slow wave structure. In contrast to its original slow wave characteristics, the guide mode becomes a fast wave in the low-frequency portion of the passband, and there exists a cut-off frequency for the guide mode. The vane-type guiding structure has been shown to limit the upper frequency of the passband of the plasma mode, compared with that of the plasma surface wave. In addition, the passband of the plasma mode increases with the plasma density while it becomes narrower for the guide mode. The influences of the parameters of the guiding structure and plasma density on the propagation of waves are also presented

An Empirical Model for Vane-Type Vortex Generators in a Navier-Stokes Code

Science.gov (United States)

Dudek, Julianne C.

2005-01-01

An empirical model which simulates the effects of vane-type vortex generators in ducts was incorporated into the Wind-US Navier-Stokes computational fluid dynamics code. The model enables the effects of the vortex generators to be simulated without defining the details of the geometry within the grid, and makes it practical for researchers to evaluate multiple combinations of vortex generator arrangements. The model determines the strength of each vortex based on the generator geometry and the local flow conditions. Validation results are presented for flow in a straight pipe with a counter-rotating vortex generator arrangement, and the results are compared with experimental data and computational simulations using a gridded vane generator. Results are also presented for vortex generator arrays in two S-duct diffusers, along with accompanying experimental data. The effects of grid resolution and turbulence model are also examined.

Nuclear fuel assembly incorporating primary and secondary structural support members

International Nuclear Information System (INIS)

Carlson, W.R.; Gjertsen, R.K.; Miller, J.V.

1987-01-01

A nuclear fuel assembly, comprising: (a) an upper end structure; (b) a lower end structure; (c) elongated primary structural members extending longitudinally between and rigidly interconnecting the upper and lower end structures, the upper and lower end structures and primary structural members together forming a rigid structural skeleton of the fuel assembly; (d) transverse grids supported on the primary structural members at axially spaced locations therealong between the upper and lower end structures; (e) fuel rods extending through and supported by the grids between the upper and lower end structures so as to extend in generally side-by-side spaced relation to one another and to the primary structural members; and (f) elongated secondary structural members extending longitudinally between but unconnected with the upper and lower end structures, the secondary structural members extending through and rigidly interconnected with the grids to extend in generally side-by-side spaced relation to one another, to the fuel rods and to the primary structural members so as to bolster the stiffness of the structural skeleton of the fuel assembly

Advanced Instrumentation for Measuring Fluid-Structure Coupling Phenomena in the Guide Vanes Cascade of a Pump-Turbine Scale Model

OpenAIRE

Roth, Steven; Hasmatuchi, Vlad; Botero, Francisco; Farhat, Mohamed; Avellan, François

2010-01-01

In the present study, the fluid-structure coupling is investigated in the guide vanes of a pump-turbine scale model placed in one of the test rigs of the Laboratory for Hydraulic Machines (EPFL) in Lausanne. The paper focuses on the advanced instrumentation used to get reliable and complete fluid-structure coupling results. Semi-conductor strain gages are installed on three guide vanes which are especially weakened to account for stronger fluid-structure coupling phenomena. These are statical...

Characterization of Rotating Detonation Engine Exhaust Through Nozzle Guide Vanes

Science.gov (United States)

2013-03-21

ENY/13-M09 Abstract A Rotating Detonation Engine ( RDE ) has higher thermal efficiencies in comparison to its traditional gas turbine counterparts. Thus...as budgets decrease and fuel costs increase, RDEs have become a research focus for the United States Air Force. An integration assembly for attaching...the first Nozzle Guide Vane (NGV) section from a T63 gas turbine engine to a 6 inch diameter RDE was designed and built for this study. Pressure

Aerodynamic forces estimation on jet vanes exposed to supersonic exhaust of a CD Nozzle

International Nuclear Information System (INIS)

Bukhari, S.B.H.; Jehan, I.; Zahir, S.; Khan, M.A.

2003-01-01

A comprehensive study has been made for the estimation of aerodynamic forces on the jet Vane placed in the supersonic exhaust of a Convergent Divergent, CD-Nozzle. Such a system is used to provide the control forces that consist of four orthogonal vanes mounted in the supersonic exhaust of the CD-Nozzles. The flow field parameters for a CD Nozzle were analyzed and validated earlier. In this paper the published experimental and CFD results from RAMPANT Code from Fluent Inc. were used to estimate the axial and normal forces by using PAK-3D, a Computational Fluid Dynamics (CFD) software based on Navier-Stokes Equations solver. Results got verified quantitatively with a maximum error of 8% between PAK-3D and experiment, while 4% between PAK-3D and a CFD code, RAMPANT for the axial force. (author)

Analysis of swirl recovery vanes for increased propulsive efficiency in tractor propeller aircraft

NARCIS (Netherlands)

Veldhuis, L.L.M.; Stokkermans, T.C.A.; Sinnige, T.; Eitelberg, G.

2016-01-01

In this paper we address a preliminary assessment of the performance effects of swirl recovery vanes (SRVs) in a installed and uninstalled tractor propeller arrangement. A numerical analysis was performed on a propeller and a propeller-wing configuration after the SRVs were optimized first in a

Automatic efficiency optimization of an axial compressor with adjustable inlet guide vanes

Science.gov (United States)

Li, Jichao; Lin, Feng; Nie, Chaoqun; Chen, Jingyi

2012-04-01

The inlet attack angle of rotor blade reasonably can be adjusted with the change of the stagger angle of inlet guide vane (IGV); so the efficiency of each condition will be affected. For the purpose to improve the efficiency, the DSP (Digital Signal Processor) controller is designed to adjust the stagger angle of IGV automatically in order to optimize the efficiency at any operating condition. The A/D signal collection includes inlet static pressure, outlet static pressure, outlet total pressure, rotor speed and torque signal, the efficiency can be calculated in the DSP, and the angle signal for the stepping motor which control the IGV will be sent out from the D/A. Experimental investigations are performed in a three-stage, low-speed axial compressor with variable inlet guide vanes. It is demonstrated that the DSP designed can well adjust the stagger angle of IGV online, the efficiency under different conditions can be optimized. This establishment of DSP online adjustment scheme may provide a practical solution for improving performance of multi-stage axial flow compressor when its operating condition is varied.

Methodology of Computer-Aided Design of Variable Guide Vanes of Aircraft Engines

Science.gov (United States)

Falaleev, Sergei V.; Melentjev, Vladimir S.; Gvozdev, Alexander S.

2016-01-01

The paper presents a methodology which helps to avoid a great amount of costly experimental research. This methodology includes thermo-gas dynamic design of an engine and its mounts, the profiling of compressor flow path and cascade design of guide vanes. Employing a method elaborated by Howell, we provide a theoretical solution to the task of…

Gas turbine structural mounting arrangement between combustion gas duct annular chamber and turbine vane carrier

Science.gov (United States)

Wiebe, David J.; Charron, Richard C.; Morrison, Jay A.

2016-10-18

A gas turbine engine ducting arrangement (10), including: an annular chamber (14) configured to receive a plurality of discrete flows of combustion gases originating in respective can combustors and to deliver the discrete flows to a turbine inlet annulus, wherein the annular chamber includes an inner diameter (52) and an outer diameter (60); an outer diameter mounting arrangement (34) configured to permit relative radial movement and to prevent relative axial and circumferential movement between the outer diameter and a turbine vane carrier (20); and an inner diameter mounting arrangement (36) including a bracket (64) secured to the turbine vane carrier, wherein the bracket is configured to permit the inner diameter to move radially with the outer diameter and prevent axial deflection of the inner diameter with respect to the outer diameter.

Novel investigation of the different Omni-direction-guide-vane angles effects on the urban vertical axis wind turbine output power via three-dimensional numerical simulation

International Nuclear Information System (INIS)

Shahizare, B.; Nik-Ghazali, N.; Chong, W.T.; Tabatabaeikia, S.; Izadyar, Nima; Esmaeilzadeh, Alireza

2016-01-01

Highlights: • Investigation of the Omni-direction-guide-vane impacts on the VAWT performance. • Obtain the best position of the guide vane angles in order to achieve the maximum performance. • Validation of the 3D computational fluid dynamics with experimental data. • Acquire the optimal Omni-direction-guide-vane based on numerical simulation results. - Abstract: The aim of this study is to present the effects of different Omni-direction-guide-vane (ODGV) angles on the performance of the vertical axis wind turbine (VAWT). For this purpose, five different straight-bladed VAWTs have been simulated via three-dimensional (3D) computational fluid dynamics (CFD). Hence, the VAWT without ODGV covering, were simulated and validated via CFD and experimental fluid dynamics (EFD) data, respectively in the first step. Indeed, grid and time step independency test as well as the effect of domain size, have been conducted and a suitable agreement was found based on comparison of the CFD and EFD results. In the next step, the VAWT was shrouded by ODGV cover and the whole system was simulated for 52 angles of the ODGV in four different tip speed ratios (TSR), to investigate the impact of guide vanes angles on the VAWT performance. Results of this study indicated that output power of the VAWT with α = 20° and β = 55° ODGV guide vanes, was improved 40.9%, 36.5%, 35.3% and 33.2%, respectively in four different TSR including 0.745, 1.091, 1.901 and 2.53.

3D shape optimization of fan vanes for multiple operating regimes subject to efficiency and noise-related excellence criteria and constraints

Directory of Open Access Journals (Sweden)

Ivo Marinić-Kragić

2016-01-01

Full Text Available Fully generic 3D shapes of centrifugal roof fan vanes are explored based on a custom-developed numerical workflow with the ability to vary the vane 3D shape by manipulating the control points of parametric surfaces and change the number of vanes and rotation speed. An excellence formulation is based on design flow efficiency, multi-regime operational conditions and noise criteria for various cases, including multi-objective optimization. Multiple cases of optimization demonstrate the suitability of customized and individualized fan designs for specific working environments according to the selected excellence criteria. Noise analysis is considered as an additional decision-making tool for cases where multiple solutions of equal efficiency are generated and as an additional criteria for multi-objective optimization. The 3D vane shape enables further gains in efficiency compared to 2D shape optimization, while multi-objective optimization with noise as an additional criterion shows potential to greatly reduce the roof fan noise with only small losses in efficiency. The developed workflow which comprises (i a 3D parametric shape modeler, (ii an evolutionary optimizer and (iii a computational fluid dynamics (CFD simulator can be viewed as an integral tool for optimizing the designs of roof fans under custom conditions.

Influence of the Applied Working Fluid and the Arrangement of the Steering Edges on Multi-Vane Expander Performance in Micro ORC System

Directory of Open Access Journals (Sweden)

Józef Rak

2018-04-01

Full Text Available Micro-power domestic organic Rankine cycle (ORC systems are nowadays of great interest. These systems are considered for combined heat and power (CHP generation in domestic and distributed applications. The main issues of ORC systems design is selection of the expander and the working fluid. Thanks to their positive features, multi-vane expanders are especially promising for application in micro-power ORC systems. These expanders are very simple in design, small in dimensions, inexpensive and feature low gas flow capacity and expansion ratio. The application of multi-vane expanders in ORC systems is innovative and currently limited to prototype applications. However, a literature review indicates the growing interest in these machines and the potential for practical implementation. For this reason, it is necessary to conduct detailed studies on the multi-vane expanders operation in ORC systems. In this paper the results of experimental and numerical investigations on the influence of the applied working fluid and the arrangement of the steering edges on multi-vane expander performance in micro ORC system are reported. The experiments were performed using the specially designed lab test-stand, i.e. the domestic ORC system. Numerical simulations were proceeded in ANSYS CFX software (ANSYS, Inc., Canonsburg, PA, USA and were focused on determining the expander performance under various flow conditions of different working fluids. Detailed numerical analysis of the arrangement of the machine steering edges showed existence of optimal mutual position of the inlet and outlet port for which the multi-vane expander achieves maximum internal work and internal efficiency.

The impact of inlet angle and outlet angle of guide vane on pump in reversal based hydraulic turbine performance

International Nuclear Information System (INIS)

Shi, F X; Yang, J H; Wang, X H; Zhang, R H; Li, C E

2012-01-01

In this paper, in order to research the impact of inlet angle and outlet angle of guide vane on hydraulic turbine performance, a centrifugal pump in reversal is adopted as turbine. A numerical simulation method is adopted for researching outer performance and flow field of turbine. The results show: inlet angle has a crucial role to turbine, to the same flow, there is a noticeable decline for the efficiency and head of turbine with the inlet angle increases. At the best efficiency point(EFP),to a same inlet angle, when the inlet angle greater than inlet angle, velocity circulation in guide vane outlet decreases, which lead the efficiency of turbine to reduce, Contrarily, the efficiency rises. With the increase of inlet angle and outlet angle, the EFP moves to the big flow area and the uniformity of pressure distribution becomes worse. The paper indicates that the inlet angle and outlet angle have great impact on the turbine performance, and the best combination exists for the inlet angle and outlet angle of the guide vane.

Thermal modelling of a dry revolving vane compressor

Science.gov (United States)

Ooi, K. T.; Aw, K. T.

2017-08-01

The lubricant used in compressors serves to lubricate, to seal the gaps to reduce internal leakage and to a certain extent, to cool. However, a lubricant free compressor is attractive if lubricants become a source of contaminant, or in areas where the compressor needs be placed under any orientation, such as those in military or portable computing. In this paper, a thermal model for a dry revolving vane compressor is presented. This thermal model sets out to predict the steady-state operating temperatures of the compressor components. The lumped thermal conductance method was employed. The results of the components temperature will be presented and discussed. A high potential for overheating is observed at the shaft bearings.

Effect of turbulence intensity on cross-injection film cooling at a stepped or smooth endwall of a gas turbine vane passage.

Science.gov (United States)

Wu, Pey-Shey; Tsai, Shen-Ta; Jhuo, Yue-Hua

2014-01-01

This study is concerned with a film cooling technique applicable to the protection of the endwalls of a gas turbine vane. In the experiments, cross-injection coolant flow from two-row, paired, inclined holes with nonintersecting centerlines was utilized. The test model is a scaled two-half vane. The levels of turbulence intensity used in the experiments are T.I. = 1.8%, 7%, and 12%. Other parameters considered in the film cooling experiments include three inlet Reynolds numbers (9.20 × 10(4), 1.24 × 10(5), and 1.50 × 10(5)), three blowing ratios (0.5, 1.0, and 2.0), and three endwall conditions (smooth endwall and stepped endwall with forward-facing or backward-facing step). Thermochromic liquid crystal (TLC) technique with steady-state heat transfer experiments was used to obtain the whole-field film cooling effectiveness. Results show that, at low turbulence intensity, increasing Reynolds number decreases the effectiveness in most of the vane passage. There is no monotonic trend of influence by Reynolds number at high turbulence intensity. The effect of blowing ratio on the effectiveness has opposite trends at low and high turbulence levels. Increasing turbulent intensity decreases the effectiveness, especially near the inlet of the vane passage. With a stepped endwall, turbulence intensity has only mild effect on the film cooling effectiveness.

Effect of Turbulence Intensity on Cross-Injection Film Cooling at a Stepped or Smooth Endwall of a Gas Turbine Vane Passage

Directory of Open Access Journals (Sweden)

Pey-Shey Wu

2014-01-01

Full Text Available This study is concerned with a film cooling technique applicable to the protection of the endwalls of a gas turbine vane. In the experiments, cross-injection coolant flow from two-row, paired, inclined holes with nonintersecting centerlines was utilized. The test model is a scaled two-half vane. The levels of turbulence intensity used in the experiments are T.I.=1.8%, 7%, and 12%. Other parameters considered in the film cooling experiments include three inlet Reynolds numbers (9.20×104 , 1.24×105, and  1.50×105, three blowing ratios (0.5, 1.0, and 2.0, and three endwall conditions (smooth endwall and stepped endwall with forward-facing or backward-facing step. Thermochromic liquid crystal (TLC technique with steady-state heat transfer experiments was used to obtain the whole-field film cooling effectiveness. Results show that, at low turbulence intensity, increasing Reynolds number decreases the effectiveness in most of the vane passage. There is no monotonic trend of influence by Reynolds number at high turbulence intensity. The effect of blowing ratio on the effectiveness has opposite trends at low and high turbulence levels. Increasing turbulent intensity decreases the effectiveness, especially near the inlet of the vane passage. With a stepped endwall, turbulence intensity has only mild effect on the film cooling effectiveness.

Enhancing sediment distribution at the vicinity of power plant intakes using double rows of vanes and groins (Case study: New tebbin power plant

Directory of Open Access Journals (Sweden)

Sayed Mahgoub

2013-12-01

The study results showed that, in case of vanes absence, sediments with rates 1–2 m3/week were stuck within the sediment trap under the winter conditions. Also, the results indicated that the submerged vanes play an important role in preventing the sediment intrusion. Also, it was clear that using groins might lead to enhancing the sediment distribution at the intake vicinity.

Loss model for off-design performance analysis of radial turbines with pivoting-vane, variable-area stators

Science.gov (United States)

Meitner, P. L.; Glassman, A. J.

1980-01-01

An off-design performance loss model for a radial turbine with pivoting, variable-area stators is developed through a combination of analytical modeling and experimental data analysis. A viscous loss model is used for the variation in stator loss with setting angle, and stator vane end-clearance leakage effects are predicted by a clearance flow model. The variation of rotor loss coefficient with stator setting angle is obtained by means of an analytical matching of experimental data for a rotor that was tested with six stators, having throat areas from 20 to 144% of the design area. An incidence loss model is selected to obtain best agreement with experimental data. The stator vane end-clearance leakage model predicts increasing mass flow and decreasing efficiency as a result of end-clearances, with changes becoming significantly larger with decreasing stator area.

Flow characteristics of guide vane of diffuser pump by PIV measurement

International Nuclear Information System (INIS)

Kim, J. H.; Lee, Young Ho; Choi, J. W.; Kim, M. Y.; Lee, H.

2000-01-01

The present experimental study is focused on the application of multi-point simultaneous measurement by PIV(Particle Image Velocimetry) to guide vane region within a diffuser pump. Various different kinds of clearance were selected as experimental conditions. Optimized cross correlation identification to obtain velocity vectors was implemented with direct calculation of correlation coefficients. Fine optical setup important in PIV performance is arranged for the accurate PIV measurement of high-speed complex flow. Various flow patterns are represented quantitatively at the stator passages

Numerical Investigations of Unsteady Flow in a Centrifugal Pump with a Vaned Diffuser

Directory of Open Access Journals (Sweden)

Olivier Petit

2013-01-01

Full Text Available Computational fluid dynamics (CFD analyses were made to study the unsteady three-dimensional turbulence in the ERCOFTAC centrifugal pump test case. The simulations were carried out using the OpenFOAM Open Source CFD software. The test case consists of an unshrouded centrifugal impeller with seven blades and a radial vaned diffuser with 12 vanes. A large number of measurements are available in the radial gap between the impeller and the diffuse, making this case ideal for validating numerical methods. Results of steady and unsteady calculations of the flow in the pump are compared with the experimental ones, and four different turbulent models are analyzed. The steady simulation uses the frozen rotor concept, while the unsteady simulation uses a fully resolved sliding grid approach. The comparisons show that the unsteady numerical results accurately predict the unsteadiness of the flow, demonstrating the validity and applicability of that methodology for unsteady incompressible turbomachinery flow computations. The steady approach is less accurate, with an unphysical advection of the impeller wakes, but accurate enough for a crude approximation. The different turbulence models predict the flow at the same level of accuracy, with slightly different results.

MATHEMATICAL MODEL FOR THE STUDY AND DESIGN OF A ROTARY-VANE GAS REFRIGERATION MACHINE

Directory of Open Access Journals (Sweden)

V. V. Trandafilov

2016-08-01

Full Text Available This paper presents a mathematical model of calculating the main parameters the operating cycle, rotary-vane gas refrigerating machine that affect installation, machine control and working processes occurring in it at the specified criteria. A procedure and a graphical method for the rotary-vane gas refrigerating machine (RVGRM are proposed. A parametric study of the main geometric variables and temperature variables on the thermal behavior of the system is analyzed. The model considers polytrope index for the compression and expansion in the chamber. Graphs of the pressure and temperature in the chamber of the angle of rotation of the output shaft are received. The possibility of inclusion in the cycle regenerative heat exchanger is appreciated. The change of the coefficient of performance machine after turning the cycle regenerative heat exchanger is analyzed. It is shown that the installation of a regenerator RVGRM cycle results in increased COP more than 30%. The simulation results show that the proposed model can be used to design and optimize gas refrigerator Stirling.

Scaling laws for gas–liquid flow in swirl vane separators

International Nuclear Information System (INIS)

Liu, Li; Bai, Bofeng

2016-01-01

Highlights: • Model for swirl vane separator performance is established with similarity criteria. • Scaling laws are developed to correlate downscale test with prototype separator. • Effects of key similarity criteria on separation performance are studied. • The vital role of droplet size distribution on separation performance is discussed. - Abstract: Laboratory tests on gas–liquid flow in swirl vane separators are usually carried out to help establish an experimental database for separator design and performance improvement. Such model tests are generally performed in the reduced scale and not on the actual working conditions. Though great efficiency is often obtainable in the reduced model, the performance of the full-sized prototype usually cannot be well predicted. To design downscale model tests and apply the experimental results to predict the prototype, a general relationship to correlate them is required. In this paper, the relation of the similitude-criterion concerning the pressure loss is presented by using the dimensionless analysis, and mathematical models for critical droplet diameter, grade efficiency and overall separation efficiency are established by analyzing the features of the droplet trajectory in gas swirling flow field. The essential similarity criteria accounting for pressure loss and separation efficiency are obtained, respectively. On this basis, the scaling laws which enable a comparison between the reduced model and the full-sized prototype under similar conditions are also developed. It is found that the overall separation efficiency is significantly affected by the size distribution of the small droplets, especially when the mean diameter is smaller than the critical droplet diameter.

Combining effect of optimized axial compressor variable guide vanes and bleed air on the thermodynamic performance of aircraft engine system

International Nuclear Information System (INIS)

Kim, Sangjo; Son, Changmin; Kim, Kuisoon

2017-01-01

Aim of this work is to provide evidence of the effectiveness of combined use of the variable guide vanes (VGVs) and bleed air on the thermodynamic performance of aircraft engine system. This paper performed the comparative study to evaluate the overall thermal performance of an aircraft engine with optimized VGVs and bleed air, separately or simultaneously. The low-bypass ratio turbofan engine has been modeled with a 0D/1D modeling approach. The genetic algorithm is employed to find the optimum schedule of VGVs and bleed air. There are four types of design variables: (1) the inlet guide vane (IGV) angle, (2) the IGV and 1st stator vane (SV) angles, (3) bleed air mass flow rate at the exit of the axial compressor, and (4) both type 2 and type 3. The optimization is conducted with surge margin constraints of more than 10% and 15% in the axial compressor. The results show that the additional use of the bleed air increases the efficiency of the compressors. Overall, the percentage reductions of the total fuel consumption for the engine with the IGV, 1st SV and bleed air schedule is 1.63% for 15% surge margin constraints when compared with the engine with the IGV schedule. - Highlights: • The effect of combined use of variable guide vanes and bleed air is evaluated. • The genetic algorithm is employed to find the optimum setting angle and bleed air. • A low bypass ratio mixed turbofan engine is analyzed for optimization. • Additional use of the bleed air shows improved overall performance of the engine.

A new low threshold bi-directional wind vane and its potential impact on unplanned atmospheric release prediction

International Nuclear Information System (INIS)

Parker, M.J.

1996-01-01

At the Savannah River Site, the Environmental Transport Group (ETG) maintains and develops a comprehensive meteorological monitoring program which employs bi-directional wind vanes (bivanes) for the measurement of horizontal and vertical wind direction and turbulence. Wind data collected near and below instrument starting thresholds under stable nighttime conditions with these bivanes can result in artificially large standard deviations of horizontal wind direction (σA). In one hypothetical case, downwind concentrations could be underestimated by a factor of 40 by using artificially high σA data in a Gaussian dispersion model. In an effort to improve low wind speed measurements of wind direction, a Cooperative Research and Development Agreement (CRADA) between Met One Instruments and the Westinghouse Savannah River Company (WSRC) has been created to improve the dynamic performance of the Met One Model 1585 Bi-Directional Wind Vane

Change of performance of a horizontal wind turbine with V type tip vane%风力机加V型小翼后的性能变化

Institute of Scientific and Technical Information of China (English)

贾瑞博; 汪建文

2011-01-01

试验和数值模拟证明,在风力机叶片的叶尖添加小翼,可以提高风能转化效率.为了清楚地了解小翼对风力机动力放大的影响,文章基于叶轮周围流场的数值模拟结果,分析了加V型小翼和不加小翼的风力机流场-速度场和压力场特性.可以看出,小翼对风力机叶片叶端的影响较大,风力机叶尖的漩涡强度降低,能量转换效率提高.%It was proved that a tip vane could improve thewind turbine's efficiency by the test and the numerical simulation. In order to distinctly understand the power augmentation effect of the wind turbine by the tip vane, this paper analyzed the flow field of the wind turbine with the V type tip vane and without a tip vane, as well as the characteristics of the velocity field and the pressure field, which based on the numerical simulation result of the flow field of the wind turbine. The tip vane has more influence to the blade tip of the wind turbine. The vortex intensity around the blade tip was reduced and the energy transformation efficiency was improved.

Mapping of the lateral flow field in typical subchannels of a support grid with vanes

International Nuclear Information System (INIS)

McClusky, Heather L.; Holloway, Mary V.; Conover, Timothy A.; Beasley, Donald E.; Conner, Michael E.; Smith III, L. David

2003-01-01

Lateral flow fields in four subchannels of a model rod bundle fuel assembly are measured using particle image velocimetry. Vanes (split-vane pairs) are located on the downstream edge of the support grids in the rod bundle fuel assembly and generate swirling flow. Measurements are acquired at a nominal Reynolds number of 28,000 and for seven streamwise locations ranging from 1.4 to 17.0 hydraulic diameters downstream of the grid. The streamwise development of the lateral flow field is divided into two regions based on the lateral flow structure. In Region I, multiple vortices are present in the flow field and vortex interactions occur. Either a single circular vortex or a hairpin shaped flow structure is formed in Region II. Lateral kinetic energy, maximum lateral velocity, centroid of vorticity, radial profiles of azimuthal velocity, and angular momentum are employed as measures of the streamwise development of the lateral flow field. The particle image velocimetry measurements of the present study are compared with laser doppler velocimetry measurements taken for the identical support grids and flow condition. (author)

On development of RFQ vanes from beam dynamics data

International Nuclear Information System (INIS)

Chatterjee, Avik; Padhi, Rakesh; Banerjee, M.K.; Naik, Vaishali; Sanyal, Dirtha; Choudhury, Siddhartha De; Chakrabarti, Alok

2005-01-01

Simulation at critical steps of product development greatly helps to detect the design flaws at the earlier stage and gives a digital platform to iterate the design and process at the initial stage. This helps to reduce the risk of failure considerably and gives an alternative to reduce the number of physical prototypes for design validation. Modern concepts of virtual prototyping for predicting functional behaviour of a product and process are gaining momentum globally as it is the fully integrated approach to converge the concepts of functional design, Design for Manufacturing (DFM), Design for Assembly (DFA) and manufacturing process simulation. This concept has been partially implemented in development of RFQ (Radio Frequency Quadruple) vanes and the basic guidelines have been discussed. (author)

Investigation of the Optimal Omni-Direction-Guide-Vane Design for Vertical Axis Wind Turbines Based on Unsteady Flow CFD Simulation

Directory of Open Access Journals (Sweden)

Behzad Shahizare

2016-03-01

Full Text Available With soaring energy demands, the desire to explore alternate and renewable energy resources has become the focal point of various active research fronts. Therefore, the scientific community is revisiting the notion to tap wind resources in more rigorous and novel ways. In this study, a two-dimensional computational investigation of the vertical axis wind turbine (VAWT with omni-direction-guide-vane (ODGV is proposed to determine the effects of this guide vane. In addition, the mesh and time step (dt size dependency test, as well as the effect of the different turbulence models on results accuracy are investigated. Eight different shape ratios (R of the omni-direction-guide-vane were also examined in this study. Further, the CFD model is validated by comparing the numerical results with the experimental data. Validation results show a good agreement in terms of shape and trend in CFD simulation. Based on these results, all the shape ratios, except two ratios including 0.3 and 0.4 at TSR of 1.3 to 3, have a positive effect on the power and torque coefficient improvement. Moreover, results show that the best case has a shape ratio of 0.55, which improves the power coefficient by 48% and the torque coefficient up to 58%.

Preliminary results for validation of Computational Fluid Dynamics for prediction of flow through a split vane spacer grid

International Nuclear Information System (INIS)

Rashkovan, A.; Novog, D.R.

2012-01-01

This paper presents the results of the CFD simulations of turbulent flow past spacer grid with mixing vanes. This study summarizes the first stage of the ongoing numerical blind exercise organized by OECD-NEA. McMaster University along with other participants plan to submit a numerical prediction of the detailed flow field and turbulence characteristics of the flow past 5x5 rod bundle with a spacer grid equipped with two types of mixing vanes. The results will be compared with blind experimental measurements performed in Korea. Due to the fact that a number of the modeling strategies are suggested in literature for such types of flows, we have performed a series of tests to assess the mesh requirements, flow steadiness, turbulence modeling and wall treatment effects. Results of these studies are reported in the present paper. (author)

2.5 MeV CW 4-vane RFQ accelerator design for BNCT applications

Science.gov (United States)

Zhu, Xiaowen; Wang, Hu; Lu, Yuanrong; Wang, Zhi; Zhu, Kun; Zou, Yubin; Guo, Zhiyu

2018-03-01

Boron Neutron Capture Therapy (BNCT) promises a bright future in cancer therapy for its highly selective destruction of cancer cells, using the 10B +n→7Li +4 He reaction. It offers a more satisfactory therapeutic effect than traditional methods for the treatment of malignant brain tumors, head and neck cancer, melanoma, liver cancer and so on. A CW 4-vane RFQ, operating at 162.5 MHz, provides acceleration of a 20 mA proton beam to 2.5 MeV, bombarding a liquid lithium target for neutron production with a soft neutron energy spectrum. The fast neutron yield is about 1.73×1013 n/s. We preliminarily develop and optimize a beam shaping assembly design for the 7Li(p, n)7Be reaction with a 2.5 MeV proton beam. The epithermal neutron flux simulated at the beam port will reach up to 1 . 575 ×109 n/s/cm2. The beam dynamics design, simulation and benchmark for 2.5 MeV BNCT RFQ have been performed with both ParmteqM (V3.05) and Toutatis, with a transmission efficiency higher than 99.6% at 20 mA. To ease the thermal management in the CW RFQ operation, we adopt a modest inter-vane voltage design (U = 65 kV), though this does increase the accelerator length (reaching 5.2 m). Using the well-developed 3D electromagnetic codes, CST MWS and ANSYS HFSS, we are able to deal with the complexity of the BNCT RFQ, taking the contribution of each component in the RF volume into consideration. This allows us to optimize the longitudinal field distribution in a full-length model. Also, the parametric modeling technique is of great benefit to extensive modifications and simulations. In addition, the resonant frequency tuning of this RFQ is studied, giving the tuning sensitivities of vane channel and wall channel as -16.3 kHz/°C and 12.4 kHz/°C, respectively. Finally, both the multipacting level of this RFQ and multipacting suppressing in the coaxial coupler are investigated.

Effects of Mie tip-vane on pressure distribution of rotor blade and power augmentation of horizontal axis wind turbine; Yokutan shoyoku Mie ben ni yoru suiheijiku fusha yokumenjo no atsuryoku bunpu no kaizen to seino kojo tono kankei

Energy Technology Data Exchange (ETDEWEB)

Shimizu, Y.; Maeda, T.; Kamada, Y. [Mie Univ., Mie (Japan); Seto, H. [Mitsubishi Motors Corp., Tokyo (Japan)

2000-04-01

By recent developments of exclusive rotor blade, the efficiency of wind turbine is improved substantially. By measuring pressure on rotor blades of horizontal axis wind turbines rotating in wind tunnels, this report clarified relation between improvement of pressure distribution on main rotor blades by Mie vane and upgrade of wind turbine performance. The results under mentioned have been got by measuring pressure distribution on rotor blades, visualization by tuft, and measuring resistance of Mie vane. (1) The difference of pressure between suction surface and pressure surface on the end of rotor blade increase, and output power of wind turbine improves. (2) Vortex of blade end is inhibited by Mie vane. (3) The reason of reduction on wind turbine performance with Mie vane in aria of high rotating speed ratio is the increase of Mie vane flow resistance.(NEDO)

Influence of omni-directional guide vane on the performance of cross-flow rotor for urban wind energy

Science.gov (United States)

Wicaksono, Yoga Arob; Tjahjana, Dominicus Danardono Dwi Prija; Hadi, Syamsul

2018-02-01

Vertical axis wind turbine like cross-flow rotor have some advantage there are, high self-starting torque, low noise, and high stability; so, it can be installed in the urban area to produce electricity. But, the urban area has poor wind condition, so the cross-flow rotor needs a guide vane to increase its performance. The aim of this study is to determine experimentally the effect of Omni-Directional Guide Vane (ODGV) on the performance of a cross-flow wind turbine. Wind tunnel experiment has been carried out for various configurations. The ODGV was placed around the cross-flow rotor in order to increase ambient wind environment of the wind turbine. The maximum power coefficient is obtained as Cpmax = 0.125 at 60° wind direction. It was 21.46% higher compared to cross-flow wind turbine without ODGV. This result showed that the ODGV able to increase the performance of the cross-flow wind turbine.

3D computations of flow field in a guide vane blading designed by means of 2D model for a low head hydraulic turbine

International Nuclear Information System (INIS)

Krzemianowski, Z; Puzyrewski, R

2014-01-01

The paper presents the main parameters of the flow field behind the guide vane cascade designed by means of 2D inverse problem and following check by means of 3D commercial program ANSYS/Fluent applied for a direct problem. This approach of using different models reflects the contemporary design procedure for non-standardized turbomachinery stage. Depending on the model, the set of conservation equation to be solved differs, although the physical background remains the same. The example of computations for guide vane cascade for a low head hydraulic turbine is presented.

Proposal of a novel compact P-band magnetically insulated transmission line oscillator with inclined vanes

Science.gov (United States)

Zhang, Xiaoping; Dang, Fangchao; Li, Yangmei; Jin, Zhenxing

2015-06-01

In this paper, we present a novel compact P-band magnetically insulated transmission line oscillator (MILO) with specially inclined slow-wave-structure (SWS) vanes to decrease its total dimension and weight. The dispersion characteristics of the inclined SWS are investigated in detail and made comparisons with that of the traditional straight SWS. The results show that the inclined SWS is more advantageous in operating on a steady frequency in a wide voltage range and has a better asymmetric mode segregation and a relatively large band-gap between the TM00 and TM01 modes which are in favor of avoiding the asymmetric and transverse mode competition. Besides, the transverse dimension of the proposed novel inclined SWS with the same operation frequency is decreased by about 50%, and correspondingly the device volume shrinks remarkably to its 0.35 times. In particle-in-cell simulation, the electron bunching spokes are obviously formed in the inclined SWS, and a P-band high-power microwave with a power of 5.8 GW, frequency of 645 MHz, and efficiency of 17.2% is generated by the proposed device, which indicates the feasibility of the compact design with the inclined vanes at the P-band.

Cooling Strategies for Vane Leading Edges in a Syngas Environment Including Effects of Deposition and Turbulence

Energy Technology Data Exchange (ETDEWEB)

Ames, Forrest [Univ. of North Dakota, Grand Forks, ND (United States); Bons, Jeffrey [Univ. of North Dakota, Grand Forks, ND (United States)

2014-09-30

The Department of Energy has goals to move land based gas turbine systems to alternate fuels including coal derived synthetic gas and hydrogen. Coal is the most abundant energy resource in the US and in the world and it is economically advantageous to develop power systems which can use coal. Integrated gasification combined cycles are (IGCC) expected to allow the clean use of coal derived fuels while improving the ability to capture and sequester carbon dioxide. These cycles will need to maintain or increase turbine entry temperatures to develop competitive efficiencies. The use of coal derived syngas introduces a range of potential contaminants into the hot section of the gas turbine including sulfur, iron, calcium, and various alkali metals. Depending on the effectiveness of the gas clean up processes, there exists significant likelihood that the remaining materials will become molten in the combustion process and potentially deposit on downstream turbine surfaces. Past evidence suggests that deposition will be a strong function of increasing temperature. Currently, even with the best gas cleanup processes a small level of particulate matter in the syngas is expected. Consequently, particulate deposition is expected to be an important consideration in the design of turbine components. The leading edge region of first stage vanes most often have higher deposition rates than other areas due to strong fluid acceleration and streamline curvature in the vicinity of the surface. This region remains one of the most difficult areas in a turbine nozzle to cool due to high inlet temperatures and only a small pressure ratio for cooling. The leading edge of a vane often has relatively high heat transfer coefficients and is often cooled using showerhead film cooling arrays. The throat of the first stage nozzle is another area where deposition potentially has a strongly adverse effect on turbine performance as this region meters the turbine inlet flow. Based on roughness

Turbine blade and vane heat flux sensor development, phase 2

Science.gov (United States)

Atkinson, W. H.; Cyr, M. A.; Strange, R. R.

1985-01-01

The development of heat flux sensors for gas turbine blades and vanes and the demonstration of heat transfer measurement methods are reported. The performance of the heat flux sensors was evaluated in a cylinder in cross flow experiment and compared with two other heat flux measurement methods, the slug calorimeter and a dynamic method based on fluctuating gas and surface temperature. Two cylinders, each instrumented with an embedded thermocouple sensor, a Gardon gauge, and a slug calorimeter, were fabricated. Each sensor type was calibrated using a quartz lamp bank facility. The instrumented cylinders were then tested in an atmospheric pressure combustor rig at conditions up to gas stream temperatures of 1700K and velocities to Mach 0.74. The test data are compared to other measurements and analytical prediction.

Prospects for the domestic production of large-sized cast blades and vanes for industrial gas turbines

Science.gov (United States)

Kazanskiy, D. A.; Grin, E. A.; Klimov, A. N.; Berestevich, A. I.

2017-10-01

Russian experience in the production of large-sized cast blades and vanes for industrial gas turbines is analyzed for the past decades. It is noted that the production of small- and medium-sized blades and vanes made of Russian alloys using technologies for aviation, marine, and gas-pumping turbines cannot be scaled for industrial gas turbines. It is shown that, in order to provide manufacturability under large-scale casting from domestic nickel alloys, it is necessary to solve complex problems in changing their chemical composition, to develop new casting technologies and to optimize the heat treatment modes. An experience of PAO NPO Saturn in manufacturing the blades and vanes made of ChS88U-VI and IN738-LC foundry nickel alloys for the turbines of the GTE-110 gas turbine unit is considered in detail. Potentialities for achieving adopted target parameters for the mechanical properties of working blades cast from ChS88UM-VI modified alloy are established. For the blades made of IN738-LC alloy manufactured using the existing foundry technology, a complete compliance with the requirements of normative and technical documentation has been established. Currently, in Russia, the basis of the fleet of gas turbine plants is composed by foreign turbines, and, for the implementation of the import substitution program, one can use the positive experience of PAO NPO Saturn in casting blades from IN738-LC alloy based on a reverse engineering technique. A preliminary complex of studies of the original manufacturer's blades should be carried out, involving, first of all, the determination of geometric size using modern measurement methods as well as the studies on the chemical compositions of the used materials (base metal and protective coatings). Further, verifying the constructed calculation models based on the obtained data, one could choose available domestic materials that would meet the operating conditions of the blades according to their heat resistance and corrosion

Computational Fluid Dynamics (CFD) Analyses in Support of Space Shuttle Main Engine (SSME) Heat Exchanger (HX) Vane Cracking Investigation

Science.gov (United States)

Garcia, Roberto; Benjamin, Theodore G.; Cornelison, J.; Fredmonski, A. J.

1993-01-01

Integration issues involved with installing the alternate turbopump (ATP) High Pressure Oxygen Turbopump (HPOTP) into the SSME have raised questions regarding the flow in the HPOTP turnaround duct (TAD). Steady-state Navier-Stokes CFD analyses have been performed by NASA and Pratt & Whitney (P&W) to address these questions. The analyses have consisted of two-dimensional axisymmetric calculations done at Marshall Space Flight Center and three-dimensional calculations performed at P&W. These analyses have identified flowfield differences between the baseline ATP and the Rocketdyne configurations. The results show that the baseline ATP configuration represents a more severe environment to the inner HX guide vane. This vane has limited life when tested in conjunction with the ATP but infinite life when tested with the current SSME HPOTP. The CFD results have helped interpret test results and have been used to assess proposed redesigns. This paper includes details of the axisymmetric model, its results, and its contribution towards resolving the problem.

Acting in solidarity: Testing an extended dual pathway model of collective action by bystander group members.

Science.gov (United States)

Saab, Rim; Tausch, Nicole; Spears, Russell; Cheung, Wing-Yee

2015-09-01

We examined predictors of collective action among bystander group members in solidarity with a disadvantaged group by extending the dual pathway model of collective action, which proposes one efficacy-based and one emotion-based path to collective action (Van Zomeren, Spears, Fischer, & Leach, 2004). Based on two proposed functions of social identity performance (Klein, Spears, & Reicher, 2007), we distinguished between the efficacy of collective action at consolidating the identity of a protest movement and its efficacy at achieving social change (political efficacy). We expected identity consolidation efficacy to positively predict collective action tendencies directly and indirectly via political efficacy. We also expected collective action tendencies to be positively predicted by moral outrage and by sympathy in response to disadvantaged outgroup's suffering. These hypotheses were supported in two surveys examining intentions to protest for Palestine in Britain (Study 1), and intentions to attend the June 4th vigil in Hong Kong to commemorate the Tiananmen massacre among a sample of Hong Kong citizens (Study 2). The contributions of these findings to research on the dual pathway model of collective action and the different functions of collective action are discussed. © 2014 The British Psychological Society.

LOX/LH2 vane pump for auxiliary propulsion systems

Science.gov (United States)

Hemminger, J. A.; Ulbricht, T. E.

1985-01-01

Positive displacement pumps offer potential efficiency advantages over centrifugal pumps for future low thrust space missions. Low flow rate applications, such as space station auxiliary propulsion or dedicated low thrust orbiter transfer vehicles, are typical of missions where low flow and high head rise challenge centrifugal pumps. The positive displacement vane pump for pumping of LOX and LH2 is investigated. This effort has included: (1) a testing program in which pump performance was investigated for differing pump clearances and for differing pump materials while pumping LN2, LOX, and LH2; and (2) an analysis effort, in which a comprehensive pump performance analysis computer code was developed and exercised. An overview of the theoretical framework of the performance analysis computer code is presented, along with a summary of analysis results. Experimental results are presented for pump operating in liquid nitrogen. Included are data on the effects on pump performance of pump clearance, speed, and pressure rise. Pump suction performance is also presented.

78 FR 49276 - Advisory Committee on Organ Transplantation; Request for Nominations for Voting Members

Science.gov (United States)

2013-08-13

... 25 members, who are Special Government Employees, and 5 ex-officio, non-voting members. Members and... committees; and therefore, extends particular encouragement to nominations for appropriately qualified female...

Big Gods: Extended prosociality or group binding?

Science.gov (United States)

Galen, Luke W

2016-01-01

Big Gods are described as having a "prosocial" effect. However, this conflates parochialism (group cohesion) with cooperation extended to strangers or out-group members. An examination of the cited experimental studies indicates that religion is actually associated with increased within-group parochialism, rather than extended or universal prosociality, and that the same general mechanisms underlie both religious and secular effects.

Experimental comparison of the optical measurements of a cross-flow in a rod bundle with mixing vanes

International Nuclear Information System (INIS)

Chang, Seok Kyu; Choo, Yeon Jun; Kim, Bok Deuk; Song, Chul Hwa

2008-01-01

The lateral crossflow on subchannels in a rod bundle array was investigated to understand the flow characteristics related to the mixing vane types on a spacer grid by using the PIV technique. For more measurement resolutions, a 5x5 rod bundle was fabricated a 2.6 times larger than the real rod bundle size in a pressurized water reactor. A rod-embedded optic array was specially designed and used for the illumination of the inner subchannels. The crossflow field in a subchannel was characterized by the type and the arrangement of the mixing vanes. At a near downstream location from the spacer grid (z/D h =1) in the case of the split type, a couple of small vortices were generated diagonally in a subchannel. On the other hand, in the case of the swirl type, there was a large elliptic vortex generated in the center of a subchannel. The measurement results were compared with the experimental results which had been performed with the LDV technique at the same test facility. The magnitudes of the flow velocity and the vorticity in PIV results were less than those in LDV measurement results. It was shown that the instantaneous flow fields in a subchannel frequently have quite different shapes from the averaged one

Influence of steam leakage through vane, gland, and shaft seals on rotordynamics of high-pressure rotor of a 1,000 MW ultra-supercritical steam turbine

Energy Technology Data Exchange (ETDEWEB)

Jiang, P.N. [Shanghai Jiao Tong University, Key Laboratory of Power Machinery and Engineering, Ministry of Education, School of Mechanical Engineering, Shanghai (China); Shanghai Turbine Company, Department of R and D, Shanghai (China); Wang, W.Z.; Liu, Y.Z. [Shanghai Jiao Tong University, Key Laboratory of Power Machinery and Engineering, Ministry of Education, School of Mechanical Engineering, Shanghai (China); Meng, G. [Shanghai Jiao Tong University, State Key Laboratory of Mechanical System and Vibration, School of Mechanical Engineering, Shanghai (China)

2012-02-15

A comparative analysis of the influence of steam leakage through vane, gland, and shaft seals on the rotordynamics of the high-pressure rotor of a 1,000 MW ultra-supercritical steam turbine was performed using numerical calculations. The rotordynamic coefficients associated with steam leakage through the three labyrinth seals were calculated using the control-volume method and perturbation analysis. A stability analysis of the rotor system subject to the steam forcing induced by the leakage flow was performed using the finite element method. An analysis of the influence of the labyrinth seal forcing on the rotordynamics was carried out by varying the geometrical parameters pertaining to the tooth number, seal clearance, and inner diameter of the labyrinth seals, along with the thermal parameters with respect to pressures and temperatures. The results demonstrated that the steam forcing with an increase in the length of the blade for the vane seal significantly influences the rotordynamic coefficients. Furthermore, the contribution of steam forcing to the instability of the rotor is decreased and increased with increases in the seal clearance and tooth number, respectively. The comparison of the rotordynamic coefficients associated with steam leakage through the vane seal, gland seal, and shaft seal convincingly disclosed that, although the steam forcing attenuates the stability of the rotor system, the steam turbine is still operating under safe conditions. (orig.)

导叶对涡轮型垂直轴风力机气动性能的影响%Effects of guiding vanes on aerodynamic performance of vortex vertical axis wind turbine

Institute of Scientific and Technical Information of China (English)

原红红; 赵振宙; 郑源; 黄娟

2013-01-01

To overcome the problem of low efficiency of the traditional vertical axis wind turbine, the structural advantages of the wind turbine with guiding vanes are introduced and the effects of guiding vanes on the vortex vertical axis wind turbine are analyzed in detail. Based on computational fluid dynamics theory, the slippage mesh technique and the k-ε model were used to compare the aerodynamic performance of the vortex vertical axis wind turbine with and without guiding vanes at a design velocity of 12 m/s. Studies have shown that the guiding vanes can effectively prevent the direct impact of the coming flow from acting on the suction section of the blade in the upwind area so as to decrease the drag torque, while the guiding vanes also negatively affect the performance of blades in the downwind area, but the positive effect of the former is more significant, so the performance of a wind turbine with guiding vanes greatly improves. The vortex vertical axis wind turbine with arc-type guiding vanes has a wider operating range, higher optimum tip speed ratio, and higher aerodynamic efficiency. The maximum wind power coefficient can reach 0.24 .%针对传统垂直轴风力机效率低的缺陷,阐述带导叶垂直轴风力机的结构优势,并分析导叶对涡轮型垂直轴风力机的作用。应用计算流体力学理论,在设计风速12 m/s下,采用滑移网格技术及k-着模型对有、无导叶两种涡轮型垂直轴风力机的气动性能进行比较。研究表明,导叶可以有效降低由于来流对逆风区叶片吸力面的直接冲击而造成的阻力扭矩,也会负面影响顺风区叶片的性能,但其负作用效果远不及在逆风区挡流降阻的正作用效果,故加导叶后风轮的性能会有很大提高。带弧线形导叶涡轮型垂直轴风力机最大风能利用系数可达0.24,具有工作范围广、最佳尖速比大的特点。

Tubular-Type Hydroturbine Performance for Variable Guide Vane Opening by CFD

Science.gov (United States)

Kim, Y. T.; Nam, S. H.; Cho, Y. J.; Hwang, Y. C.; Choi, Y. D.; Nam, C. D.; Lee, Y. H.

Micro hydraulic power generation which has output of less or equal to 100kW is attracting considerable attention. This is because of its small, simple, renewable, and large amount of energy resources. By using a small hydro power generator of which main concept is based on using differential water pressures in pipe lines, energy which was initially wasted by use of a reducing valve at an end of the pipeline, is collected by a turbine in the hydro power generator. A propeller shaped hydroturbine has been used in order to make use of this renewable pressure energy. In this study, in order to acquire basic design data of tubular type hydroturbine, output power, head, and efficiency characteristics due to the guide vane opening angle are examined in detail. Moreover, influences of pressure, tangential and axial velocity distributions on turbine performance are investigated by using a commercial CFD code.

Exergy Analysis of the Revolving Vane Compressed Air Engine

Directory of Open Access Journals (Sweden)

Alison Subiantoro

2016-01-01

Full Text Available Exergy analysis was applied to a revolving vane compressed air engine. The engine had a swept volume of 30 cm3. At the benchmark conditions, the suction pressure was 8 bar, the discharge pressure was 1 bar, and the operating speed was 3,000 rev·min−1. It was found that the engine had a second-law efficiency of 29.6% at the benchmark conditions. The contributors of exergy loss were friction (49%, throttling (38%, heat transfer (12%, and fluid mixing (1%. A parametric study was also conducted. The parameters to be examined were suction reservoir pressure (4 to 12 bar, operating speed (2,400 to 3,600 rev·min−1, and rotational cylinder inertia (0.94 to 2.81 g·mm2. The study found that a higher suction reservoir pressure initially increased the second-law efficiency but then plateaued at about 30%. With a higher operating speed and a higher cylinder inertia, second-law efficiency decreased. As compared to suction pressure and operating speed, cylinder inertia is the most practical and significant to be modified.

Achieving more efficient operation of the nozzle vane and rotor blade rows of gas turbines through using nonaxisymmetric end wall surfaces of interblade channels

Science.gov (United States)

Inozemtsev, A. A.; Samokhvalov, N. Yu.; Tikhonov, A. S.

2012-09-01

Results from a numerical study of three versions of the end-wall generatrix of the interblade channel used in the second-stage nozzle vanes of a prospective engine's turbine are presented. Recommendations for designing nonaxisymmetric end-wall surfaces are suggested based on the obtained data.

Developmental Complexity in Student Conduct: An Extended Case Analysis of Student Board Members

Science.gov (United States)

Bittinger, Joshua D.; Reif, Gabriel; Kimball, Ezekiel W.

2018-01-01

College students frequently serve on boards that hear cases of alleged student misconduct. These students contribute to decisions that can affect their peers' lives and make their colleges vulnerable to litigation and negative media coverage. It is critical that student board members carefully interpret all information presented in disciplinary…

Flow Range of Centrifugal Compressor Being Extended

Science.gov (United States)

Skoch, Gary J.

2001-01-01

General Aviation will benefit from turbine engines that are both fuel-efficient and reliable. Current engines fall short of their potential to achieve these attributes. The reason is compressor surge, which is a flow stability problem that develops when the compressor is subjected to conditions that are outside of its operating range. Compressor surge can occur when fuel flow to the engine is increased, temporarily back pressuring the compressor and pushing it past its stability limit, or when the compressor is subjected to inlet flow-field distortions that may occur during takeoff and landing. Compressor surge can result in the loss of an aircraft. As a result, engine designers include a margin of safety between the operating line of the engine and the stability limit line of the compressor. Unfortunately, the most efficient operating line for the compressor is usually closer to its stability limit line than it is to the line that provides an adequate margin of safety. A wider stable flow range will permit operation along the most efficient operating line of the compressor, improving the specific fuel consumption of the engine and reducing emissions. The NASA Glenn Research Center is working to extend the stable flow range of the compressor. Significant extension has been achieved in axial compressors by injecting air upstream of the compressor blade rows. Recently, the technique was successfully applied to a 4:1 pressure ratio centrifugal compressor by injecting streams of air into the diffuser. Both steady and controlled unsteady injection were used to inject air through the diffuser shroud surface and extend the range. Future work will evaluate the effect of air injection through the diffuser hub surface and diffuser vanes with the goal of maximizing the range extension while minimizing the amount of injected air that is required.

The experimental study on the wind turbine’s guide-vanes and diffuser of an exhaust air energy recovery system integrated with the cooling tower

International Nuclear Information System (INIS)

Chong, W.T.; Hew, W.P.; Yip, S.Y.; Fazlizan, A.; Poh, S.C.; Tan, C.J.; Ong, H.C.

2014-01-01

Highlights: • On-site exhaust air energy recovery turbine generator mounted above cooling tower. • Energy from wasted wind resources is re-used for electricity generation. • Optimum angle arrangement of guide-vanes and diffusers help to improve wind-flow. • Enclosure solves conventional wind turbine problems. • 13.3% reduction in CO 2 emission is expected to be achieved from this system. - Abstract: An assembly of two vertical axis wind turbines (VAWTs) and an enclosure is installed above a cooling tower to harness the discharged wind for electricity generation. The enclosure consists of guide-vanes and diffuser-plates, is used to enhance the rotational speed of the turbines for power augmentation. The angle of the guide-vanes is optimized to ensure the oncoming wind stream impinges the rotor blades of the turbine at an optimum angle. The diffuser-plates are tilted at an optimum angle to increase the discharged airflow rate. The performance of the system is tested in the laboratory followed by a field test on an actual size cooling tower. The VAWT performance is increased in the range of 7–8% with the integration of enclosure. There is no significant difference in the current consumption of the fan motor between the bare cooling tower and the one with installed VAWTs. With the presence of this system, approximately 17.5 GW h/year is expected to be recovered from 3000 units of cooling towers at commercial areas, assuming the cooling tower is driven by a 7.5 kW fan motor and operates 16 h/day. This amount of recovered energy can also be translated into 13% reduction in CO 2 emission

Atoms for peace: Extending the benefits of nuclear technologies

International Nuclear Information System (INIS)

Qian, J.; Rogov, A.

1995-01-01

The article focuses on the projects co-operatively undertaken through IAEA mechanisms to extend the reach of beneficial nuclear technologies in response to increasing demands for technical support and assistance from its Member States

The NTF Inlet Guide Vanes Thermal Gradient Problem and Its Mitigation

Science.gov (United States)

Venkat, Venki S.; Paryz, Roman W.; Bissett, Owen W.; Kilgore, W.

2013-01-01

The National Transonic Facility (NTF) utilizes Inlet Guide Vanes (IGV) to provide precise, quick response Mach number control for the tunnel. During cryogenic operations, the massive IGV structure can experience large thermal gradients, measured as "Delta T or (Delta)T", between the IGV ring and its support structure called the transfer case. If these temperature gradients are too large, the IGV structure can be stressed beyond its safety limit and cease operation. In recent years, (Delta)T readings exceeding the prescribed safety limits were observed frequently during cryogenic operations, particularly during model access. The tactical operation methods of the tunnel to minimize (Delta)T did not always succeed. One obvious option to remedy this condition is to warm up the IGV structure by disabling the main drive operation, but this "natural" warm up method can takes days in some cases, resulting in productivity loss. This paper documents the thermal gradient problem associated with the IGV structure during cryogenic operation and how the facility has recently achieved an acceptable mitigation which has resulted in improved efficiency of operations.

Application of dynamic slip wall modeling to a turbine nozzle guide vane

Science.gov (United States)

Bose, Sanjeeb; Talnikar, Chaitanya; Blonigan, Patrick; Wang, Qiqi

2015-11-01

Resolution of near-wall turbulent structures is computational prohibitive necessitating the need for wall-modeled large-eddy simulation approaches. Standard wall models are often based on assumptions of equilibrium boundary layers, which do not necessarily account for the dissimilarity of the momentum and thermal boundary layers. We investigate the use of the dynamic slip wall boundary condition (Bose and Moin, 2014) for the prediction of surface heat transfer on a turbine nozzle guide vane (Arts and de Rouvroit, 1992). The heat transfer coefficient is well predicted by the slip wall model, including capturing the transition to turbulence. The sensitivity of the heat transfer coefficient to the incident turbulence intensity will additionally be discussed. Lastly, the behavior of the thermal and momentum slip lengths will be contrasted between regions where the strong Reynolds analogy is invalid (near transition on the suction side) and an isothermal, zero pressure gradient flat plate boundary layer (Wu and Moin, 2010).

Positioning and tail rotor of a small horizontal axis wind turbine of due to the influence of drag coefficient and lift affecting vane cola

International Nuclear Information System (INIS)

Farinnas Wong, E. Y.; Jauregui Rigo, S.; Betancourt Mena, J.

2009-01-01

In the present investigation was carried out an assessment on the state of technology on guidance systems and tail protection when used in small horizontal axis wind turbines, work was improved methodological approach for the development of guidance systems queue by time of these machines, to incorporate the use of coefficients of lift and drag behavior varies according to the aspect ratio, using the principles of continuum mechanics and CFD methods. Two versions are analyzed , original and updated, the wind turbine CEET-01, on which the author would have been granted a Certificate of Patent of Invention and one of Industrial Model, the updated version was derived from the procedure proposed by the author, this presents a holder for the longest vane and a larger area in the vane. In addition to analyzing the amount and cost of power generated and the capacity factor at three locations in the province of Villa Clara it was concluded that the updated variant of the turbine CEET-01 is superior to the original

78 FR 36134 - Limitations on Terms of Consumer Credit Extended to Service Members and Dependents

Science.gov (United States)

2013-06-17

... vigilant to eliminate continuing, evolving predatory lending practices targeting service members and their... predatory marketing practices, and other abuses identified by consumer protection advocates, including the...

An interactive physics-based unmanned ground vehicle simulator leveraging open source gaming technology: progress in the development and application of the virtual autonomous navigation environment (VANE) desktop

Science.gov (United States)

Rohde, Mitchell M.; Crawford, Justin; Toschlog, Matthew; Iagnemma, Karl D.; Kewlani, Guarav; Cummins, Christopher L.; Jones, Randolph A.; Horner, David A.

2009-05-01

It is widely recognized that simulation is pivotal to vehicle development, whether manned or unmanned. There are few dedicated choices, however, for those wishing to perform realistic, end-to-end simulations of unmanned ground vehicles (UGVs). The Virtual Autonomous Navigation Environment (VANE), under development by US Army Engineer Research and Development Center (ERDC), provides such capabilities but utilizes a High Performance Computing (HPC) Computational Testbed (CTB) and is not intended for on-line, real-time performance. A product of the VANE HPC research is a real-time desktop simulation application under development by the authors that provides a portal into the HPC environment as well as interaction with wider-scope semi-automated force simulations (e.g. OneSAF). This VANE desktop application, dubbed the Autonomous Navigation Virtual Environment Laboratory (ANVEL), enables analysis and testing of autonomous vehicle dynamics and terrain/obstacle interaction in real-time with the capability to interact within the HPC constructive geo-environmental CTB for high fidelity sensor evaluations. ANVEL leverages rigorous physics-based vehicle and vehicle-terrain interaction models in conjunction with high-quality, multimedia visualization techniques to form an intuitive, accurate engineering tool. The system provides an adaptable and customizable simulation platform that allows developers a controlled, repeatable testbed for advanced simulations. ANVEL leverages several key technologies not common to traditional engineering simulators, including techniques from the commercial video-game industry. These enable ANVEL to run on inexpensive commercial, off-the-shelf (COTS) hardware. In this paper, the authors describe key aspects of ANVEL and its development, as well as several initial applications of the system.

Wind-tunnel calibration of a combined pitot-static tube and vane-type flow-angularity indicator at Mach numbers of 1.61 and 2.01

Science.gov (United States)

Sinclair, Archibald R; Mace, William D

1956-01-01

A limited calibration of a combined pitot-static tube and vane-type flow-angularity indicator has been made in the Langley 4- by 4-foot supersonic pressure tunnel at Mach numbers of 1.61 and 2.01. The results indicated that the angle-of-yaw indications were affected by unsymmetric shock effects at low angles of attack.

Studi Eksperimen Aliran Melalui Square Duct dan Square Elbow 90º dengan Double Guide Vane pada Variasi Sudut Bukaan Damper

Directory of Open Access Journals (Sweden)

Andrew Jaya Nazar

2017-01-01

Full Text Available Instalasi saluran udara tidak hanya berupa pipa lurus, tetapi juga terdapat fitting/aksesoris perpipaan misalnya elbow 90o dan damper. Aksesoris perpipaan ini berfungsi agar saluran udara dapat terpasang sesuai dengan kebutuhan. Namun, penggunaan aksesoris perpipaan ini menyebabkan bertambahnya pressure drop akibat adanya friction loss dan separation loss. Pemasangan guide vane pada elbow 90o diharapkan dapat mengurangi pressure drop karena dapat mengurangi terjadinya secondary flow, namun hal ini dapat menambah kerugian akibat gaya gesek. Saat ini penghematan energi menjadi sorotan terutama dalam dunia industri. Penurunan pressure drop pada belokan perpipaan sangat diharapkan, agar dapat menghemat energi lebih. Untuk itu perlu dilakukan usaha agar dapat menurunkan pressure drop yang terjadi. Penelitian ini dilakukan secara eksperimen dengan benda uji saluran udara yang terdiri dari: upstream duct (straight duct, square elbow 90o dengan r/Dh=1,5 dan dilengkapi double guide vane, damper, downstream duct (straight duct, dan induced fan. Pengukuran parameter yang dibutuhkan dilakukan dengan menggunakan: pitot tube, inclined manometer, pressure tranducer. Dari eksperimen ini diperoleh bahwa profil kecepatan pada masing-masing variasi sudut bukaan damper sudah mendekati keadaan recovery aliran pada akhir section baik dari bidang vertikal maupun horizontal. Pressure drop yang terjadi semakin naik seiring dengan bertambahnya nilai bilangan Reynolds dan sudut bukaan damper. Nilai konstanta damper semakin naik dari bukaan sudut 0o hingga 30o.

Numerical Study of the Effects of Thermal Barrier Coating and Turbulence Intensity on Cooling Performances of a Nozzle Guide Vane

Directory of Open Access Journals (Sweden)

Prasert Prapamonthon

2017-03-01

Full Text Available This work presents a numerical investigation of the combined effects of thermal barrier coating (TBC with mainstream turbulence intensity (Tu on a modified vane of the real film-cooled nozzle guide vane (NGV reported by Timko (NASA CR-168289. Using a 3D conjugate heat transfer (CHT analysis, the NGVs with and without TBC are simulated at three Tus (Tu = 3.3%, 10% and 20%. The overall cooling effectiveness, TBC effectiveness and heat transfer coefficient are analyzed and discussed. The results indicate the following three interesting phenomena: (1 TBC on the pressure side (PS is more effective than that on the suction side (SS due to a fewer number of film holes on the SS; (2 for all three Tus, the variation trends of the overall cooling effectiveness are similar, and TBC plays the positive and negative roles in heat flux at the same time, and significantly increases the overall cooling effectiveness in regions cooled ineffectively by cooling air; (3 when Tu increases, the TBC effect is more significant, for example, at the highest Tu (Tu = 20% the overall cooling effectiveness can increase as much as 24% in the film cooling ineffective regions, but near the trailing edge (TE and the exits and downstream of film holes on the SS, this phenomenon is slight.

Investigating temporal patterns of a native bee community in a remnant North American bunchgrass prairie using blue vane traps.

Science.gov (United States)

Kimoto, Chiho; Debano, Sandra J; Thorp, Robbin W; Rao, Sujaya; Stephen, William P

2012-01-01

Native bees are important ecologically and economically because their role as pollinators fulfills a vital ecosystem service. Pollinators are declining due to various factors, including habitat degradation and destruction. Grasslands, an important habitat for native bees, are particularly vulnerable. One highly imperiled and understudied grassland type in the United States is the Pacific Northwest Bunchgrass Prairie. No studies have examined native bee communities in this prairie type. To fill this gap, the bee fauna of the Zumwalt Prairie, a large, relatively intact remnant of the Pacific Northwest Bunchgrass Prairie, was examined. Native bees were sampled during the summers of 2007 and 2008 in sixteen 40-ha study pastures on a plateau in northeastern Oregon, using a sampling method not previously used in grassland studies-blue vane traps. This grassland habitat contained an abundant and diverse community of native bees that experienced marked seasonal and inter-annual variation, which appears to be related to weather and plant phenology. Temporal variability evident over the entire study area was also reflected at the individual trap level, indicating a consistent response across the spatial scale of the study. These results demonstrate that temporal variability in bee communities can have important implications for long-term monitoring protocols. In addition, the blue vane trap method appears to be well-suited for studies of native bees in large expanses of grasslands or other open habitats, and may be a useful tool for monitoring native bee communities in these systems.

Film cooling for a closed loop cooled airfoil

Science.gov (United States)

Burdgick, Steven Sebastian; Yu, Yufeng Phillip; Itzel, Gary Michael

2003-01-01

Turbine stator vane segments have radially inner and outer walls with vanes extending therebetween. The inner and outer walls are compartmentalized and have impingement plates. Steam flowing into the outer wall plenum passes through the impingement plate for impingement cooling of the outer wall upper surface. The spent impingement steam flows into cavities of the vane having inserts for impingement cooling the walls of the vane. The steam passes into the inner wall and through the impingement plate for impingement cooling of the inner wall surface and for return through return cavities having inserts for impingement cooling of the vane surfaces. At least one film cooling hole is defined through a wall of at least one of the cavities for flow communication between an interior of the cavity and an exterior of the vane. The film cooling hole(s) are defined adjacent a potential low LCF life region, so that cooling medium that bleeds out through the film cooling hole(s) reduces a thermal gradient in a vicinity thereof, thereby the increase the LCF life of that region.

Space and power: young mothers' management of smoking in extended families in China.

Science.gov (United States)

Mao, Aimei

2013-05-01

Multigenerational co-residence is a widespread phenomenon in China but there is little knowledge about the impact of power dynamics on smoking behaviors among extended family residents. Using a gender lens, this ethnographic study explored how young mothers in extended families in mainland China managed the smoking of their husbands and other family members. Analysis of data resulted in a model of 'two units-three domains' to reflect gendered relationships between young mothers and other family members, and young mothers' participation in family management. Exploration of the mothers' efforts to deal with household smoking using the model provided an explanation for why the young mothers had limited control over household space and could only impose partial restrictions on home smoking in the extended family. Copyright © 2013 Elsevier Ltd. All rights reserved.

Experimental measurements and analytical analysis related to gas turbine heat transfer. Part 1: Time-averaged heat-flux and surface-pressure measurements on the vanes and blades of the SSME fuel-side turbine and comparison with prediction. Part 2: Phase-resolved surface-pressure and heat-flux measurements on the first blade of the SSME fuel-side turbine

Science.gov (United States)

1994-01-01

Time averaged Stanton number and surface-pressure distributions are reported for the first-stage vane row, the first stage blade row, and the second stage vane row of the Rocketdyne Space Shuttle Main Engine two-stage fuel-side turbine. Unsteady pressure envelope measurements for the first blade are also reported. These measurements were made at 10 percent, 50 percent, and 90 percent span on both the pressure and suction surfaces of the first stage components. Additional Stanton number measurements were made on the first stage blade platform blade tip, and shroud, and at 50 percent span on the second vane. A shock tube was used as a short duration source of heated and pressurized air to which the turbine was subjected. Platinum thin-film heat flux gages were used to obtain the heat flux measurements, while miniature silicon-diaphragm flush-mounted pressure transducers were used to obtain the pressure measurements. The first stage vane Stanton number distributions are compared with predictions obtained using a version of STAN5 and a quasi-3D Navier-Stokes solution. This same quasi-3D N-S code was also used to obtain predictions for the first blade and the second vane.

Airfoil nozzle and shroud assembly

Science.gov (United States)

Shaffer, J.E.; Norton, P.F.

1997-06-03

An airfoil and nozzle assembly are disclosed including an outer shroud having a plurality of vane members attached to an inner surface and having a cantilevered end. The assembly further includes a inner shroud being formed by a plurality of segments. Each of the segments having a first end and a second end and having a recess positioned in each of the ends. The cantilevered end of the vane member being positioned in the recess. The airfoil and nozzle assembly being made from a material having a lower rate of thermal expansion than that of the components to which the airfoil and nozzle assembly is attached. 5 figs.

Behaviour of the extended Toda lattice

Science.gov (United States)

Wattis, Jonathan A. D.; Gordoa, Pilar R.; Pickering, Andrew

2015-11-01

We consider the first member of an extended Toda lattice hierarchy. This system of equations is differential with respect to one independent variable and differential-delay with respect to a second independent variable. We use asymptotic analysis to consider the long wavelength limits of the system. By considering various magnitudes for the parameters involved, we derive reduced equations related to the Korteweg-de Vries and potential Boussinesq equations.

Combustion-driven oscillation in a furnace with multispud-type gas burners. 4th Report. Effects of position of secondary air guide sleeve and openness of secondary air guide vane on combustion oscillation condition; Multispud gata gas turner ni okeru nensho shindo. 4. Nijigen kuki sleeve ichi oyobi nijigen kuki vane kaido no shindo reiki ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Akiyama, I.; Okiura, K.; Baba, A.; Orimoto, M. [Babcock-Hitachi K.K., Tokyo (Japan)

1994-07-25

Effects of the position of a secondary air guide sleeve and the openness of a secondary air guide vane on combustion oscillation conditions were studied experimentally for multispud-type gas burners. Pressure fluctuation in furnaces was analyzed with the previously reported resonance factor which was proposed as an index to represent the degree of combustion oscillation. As a result, the combustion oscillation region was largely affected by both position of a guide sleeve and openness of a guide vane. As the openness having large effect on the ratio of primary and secondary air/tertiary air and the position hardly having effect on the ratio were adjusted skillfully, the burner with no combustion oscillation region was achieved in its normal operation range. In addition, as the effect of preheating combustion air was arranged with a standard flow rate or mass flow flux of air, it was suggested the combustion oscillation region due to preheating can be described with the same manner as that due to no preheating. 5 refs., 8 figs.

Incarceration in the household: academic outcomes of adolescents with an incarcerated household member.

Science.gov (United States)

Nichols, Emily Bever; Loper, Ann Booker

2012-11-01

The United States has the highest incarceration rate in the world, yet there is relatively little information on how the removal of these adults from households impacts the youth who are left behind. This study used a child-centered lens to examine the impact of incarceration on the school outcomes of youth who resided with a family member or family associate who was incarcerated prior to the youth's 18th birthday. We used data from 11 waves of the National Longitudinal Survey of Youth: Child and Young Adult (n = 3,338, 53 % female). Initial analyses indicated that youth who experienced a household members' incarceration evidenced more socioeconomic challenges, more frequent home adversities, and lower cognitive skills relative to youth who did not experience a household members' incarceration. Results also revealed that youth who had experienced a household member's incarceration were more likely to report extended absence from school and were less likely to graduate from high school relative to those youth who did not experience a household members' incarceration. Counter to our hypotheses, results revealed the incarceration of an extended family member being in the household was the only relation significantly associated with worse school outcomes. Plausibly, families who allow non-immediate criminally involved individuals to reside in the household are experiencing a more pervasive chaotic home environment than those with a parent or sibling incarcerated. Our study suggests that efforts to address the needs of children with incarcerated parents need to be widened to those who experience the loss of any household member due to incarceration.

76 FR 67363 - Extending Religious and Family Member FICA and FUTA Exceptions to Disregarded Entities

Science.gov (United States)

2011-11-01

... unless the requisite family relationship exists between the employee and each of the partners comprising... the exceptions from employment that apply because of the existence of a family relationship between...(c). The inability of these entities to benefit from the exceptions for family employees and members...

Lateral Flow Field Behavior Downstream of Mixing Vanes In a Simulated Nuclear Fuel Rod Bundle

International Nuclear Information System (INIS)

Conner, Michael E.; Smith, L. David III; Holloway, Mary V.; Beasley, Donald E.

2004-01-01

To assess the fuel assembly performance of PWR nuclear fuel assemblies, average subchannel flow values are used in design analyses. However, for this highly complex flow, it is known that local conditions around fuel rods vary dependent upon the location of the fuel rod in the fuel assembly and upon the support grid design that maintains the fuel rod pitch. To investigate the local flow in a simulated nuclear fuel rod bundle, a testing technique has been employed to measure the lateral flow field in a 5 x 5 rod bundle. Particle Image Velocimetry was used to measure the lateral flow field downstream of a support grid with mixing vanes for four unique subchannels in the 5 x 5 bundle. The dominant lateral flow structures for each subchannel are compared in this paper including the decay of these flow structures. (authors)

Extended families of 2D arrays with near optimal auto and low cross-correlation

Science.gov (United States)

Svalbe, I. D.; Tirkel, A. Z.

2017-12-01

Families of 2D arrays can be constructed where each array has perfect autocorrelation, and the cross-correlation between any pair of family members is optimally low. We exploit equivalent Hadamard matrices to construct many families of p p × p arrays, where p is any 4k-1 prime. From these families, we assemble extended families of arrays with members that exhibit perfect autocorrelation and next-to-optimally low cross-correlation. Pseudo-Hadamard matrices are used to construct extended families using p = 4k + 1 primes. An optimal family of 31 31 × 31 perfect arrays can provide copyright protection to uniquely stamp a robust, low-visibility watermark within every frame of each second of high-definition, 30 fps video. The extended families permit the embedding of many more perfect watermarks that have next-to-minimal cross-correlations.

Active Flow Control in a Radial Vaned Diffuser for Surge Margin Improvement: A Multislot Suction Strategy

Directory of Open Access Journals (Sweden)

Aurélien Marsan

2017-01-01

Full Text Available This work is the final step of a research project that aims at evaluating the possibility of delaying the surge of a centrifugal compressor stage using a boundary-layer suction technique. It is based on Reynolds-Averaged Navier-Stokes numerical simulations. Boundary-layer suction is applied within the radial vaned diffuser. Previous work has shown the necessity to take into account the unsteady behavior of the flow when designing the active flow control technique. In this paper, a multislot strategy is designed according to the characteristics of the unsteady pressure field. Its implementation results in a significant increase of the stable operating range predicted by the unsteady RANS numerical model. A hub-corner separation still exists further downstream in the diffuser passage but does not compromise the stability of the compressor stage.

Numerical Study of Compact Plate-Fin Heat Exchanger for Rotary-Vane Gas Refrigeration Machine

Directory of Open Access Journals (Sweden)

V. V. Trandafilov

2017-10-01

Full Text Available Plate-fin heat exchangers are widely used in refrigeration technique. They are popular because of their compactness and excellent heat transfer performance. Here we present a numerical model for the development, research and optimization of a plate-fin heat exchanger for a rotary-vane gas refrigeration machine. The method of analysis by graphic method of plate - fin heat exchanger is proposed. The model describes the effects of secondary parameters such as axial thermal conductivity through a metal matrix of the heat exchanger. The influence of geometric parameters and heat transfer coefficient is studied. Graphs of dependences of length, efficiency of a fin and pressure drop in a heat exchanger on the thickness of the fin and the number of fins per meter are obtained. To analyze the results of numerical simulation, the heat exchanger was designed in the Aspen HYSYS program. The simulation results show that the total deviation from the proposed numerical model is not more than 15%. 

Film cooling air pocket in a closed loop cooled airfoil

Science.gov (United States)

Yu, Yufeng Phillip; Itzel, Gary Michael; Osgood, Sarah Jane; Bagepalli, Radhakrishna; Webbon, Waylon Willard; Burdgick, Steven Sebastian

2002-01-01

Turbine stator vane segments have radially inner and outer walls with vanes extending between them. The inner and outer walls are compartmentalized and have impingement plates. Steam flowing into the outer wall plenum passes through the impingement plate for impingement cooling of the outer wall upper surface. The spent impingement steam flows into cavities of the vane having inserts for impingement cooling the walls of the vane. The steam passes into the inner wall and through the impingement plate for impingement cooling of the inner wall surface and for return through return cavities having inserts for impingement cooling of the vane surfaces. To provide for air film cooing of select portions of the airfoil outer surface, at least one air pocket is defined on a wall of at least one of the cavities. Each air pocket is substantially closed with respect to the cooling medium in the cavity and cooling air pumped to the air pocket flows through outlet apertures in the wall of the airfoil to cool the same.

Steam exit flow design for aft cavities of an airfoil

Science.gov (United States)

Storey, James Michael; Tesh, Stephen William

2002-01-01

Turbine stator vane segments have inner and outer walls with vanes extending therebetween. The inner and outer walls have impingement plates. Steam flowing into the outer wall passes through the impingement plate for impingement cooling of the outer wall surface. The spent impingement steam flows into cavities of the vane having inserts for impingement cooling the walls of the vane. The steam passes into the inner wall and through the impingement plate for impingement cooling of the inner wall surface and for return through return cavities having inserts for impingement cooling of the vane surfaces. A skirt or flange structure is provided for shielding the steam cooling impingement holes adjacent the inner wall aerofoil fillet region of the nozzle from the steam flow exiting the aft nozzle cavities. Moreover, the gap between the flash rib boss and the cavity insert is controlled to minimize the flow of post impingement cooling media therebetween. This substantially confines outflow to that exiting via the return channels, thus furthermore minimizing flow in the vicinity of the aerofoil fillet region that may adversely affect impingement cooling thereof.

The effect of epoxidized soybean oil on mechanical and rheological properties of poly(butylene succinate)/lignin via vane extruder

Science.gov (United States)

Liu, Huanyu; Huang, Zhaoxia; Qu, Jinping; Meng, Cong

2016-03-01

Epoxidized Soybean Oil (ESO) have been used as the compatilizer in the Poly (butylene succinate)/lignin (PBS/lignin) composites. Compatibilized composites were fabricated by a novel vane extruder (VE) which can generate global and dynamic elongational flow. The effects of ESO on the mechanical, rheological properties and morphology of PBS/lignin were studied. The results indicated that the use of ESO had plasticizing effect on the matrix PBS while the addition reduced tensile strength. From SEM micrographs it could be clearly observed that there was a better interfacial adhesion between lignin and matrix. Meanwhile, rheological tests showed the incorporation of ESO improved its Newtonian behavior and can enhance PBS's flexibility.

Intermediate flow mixing nonsupport grid for BWR fuel assembly

International Nuclear Information System (INIS)

Taleyarkhan, R.P.

1987-01-01

An intermediate flow mixing nonsupport grid is described for use in a nuclear reactor fuel assembly containing an array of elongated fuel rods. The grid comprises: (a) interleaved inner straps arranged in an egg-crate configuration to define inner cell openings for receiving respective ones of the fuel rods. The inner straps have outer terminal end portions; (b) an outer peripheral strap attached to the respective terminal end portions of the inner straps to define perimeter cell openings for receiving other ones of the fuel rods. The inner straps and outer strap together have opposite upstream and downstream sides; (c) a first group of mixing vanes disposed at the downstream side and being attached on portions of the outer strap and on respective portions of the inner straps. Together with the outer strap portions, they define the perimeter cell openings. Each of the mixing vanes of the first group extend generally in a downstream direction and inwardly toward the perimeter cell openings for deflecting coolant flowing; and (d) a second group of mixing vanes disposed at the downstream side and being attached on other portions of the inner straps. Together with the respective portions, they define the inner cell openings. Each of the mixing vanes of the second group extend generally in a downstream direction and inwardly toward the inner cell openings for deflecting coolant flowing therethrough; (e) the mixing vanes of the second group are substantially smaller in size than the mixing vanes of the first group so as to generate substantially less turbulence in the portions of the coolant flowing through the inner cell openings than in the portions of the coolant flowing through the perimeter cell openings

Numerical investigation on pressure fluctuations in centrifugal compressor with different inlet guide vanes pre-whirl angles

Science.gov (United States)

Wang, Y. C.; Shi, M.; Cao, S. L.; Li, Z. H.

2013-12-01

The pressure fluctuations in a centrifugal compressor with different inlet guide vanes (IGV) pre-whirl angles were investigated numerically, as well as the pre-stress model and static structural of blade. The natural frequency was evaluated by pre-stress model analysis. The results show that, the aero-dynamic pressure acting on blade surface is smaller than rotation pre-stress, which wouldn't result in large deformation of blade. The natural frequencies with rotation pre-stress are slightly higher than without rotation pre-stress. The leading mechanism of pressure fluctuations for normal conditions is the rotor-stator (IGVs) interaction, while is serious flow separations for conditions that are close to surge line. A few frequency components in spectra are close to natural frequency, which possibly result in resonant vibration if amplitude is large enough, which is dangerous for compressor working, and should be avoided.

Teenage pregnancy in adolescents with an incarcerated household member.

Science.gov (United States)

Whalen, Mathilde Logan; Loper, Ann Booker

2014-03-01

This study examines the association between the incarceration of a household member and adolescent pregnancy, and evaluates whether this association extends beyond that of other variables associated with sexual health. We used data from 12 waves of the National Longitudinal Survey of Youth: Child and Young Adult. After eliminating males and individuals who did not respond to key questions, a sample of 1,229 girls (ages 14-19) was analyzed. Girls who experienced the incarceration of a household member faced more demographic and family environment risk factors than those who did not. Regression analyses demonstrated that the addition of a household incarceration variable afforded superior prediction of teenage pregnancy relative to the prediction based on demographic and family features alone. Programs that are directed toward reducing teen pregnancy will benefit from attention to the home situation of the at-risk girl, particularly the experience of household member incarceration and related family dynamics.

ON SOME TERMS DENOTING CREW MEMBERS ON DUBROVNIK SHIPS

Directory of Open Access Journals (Sweden)

Ariana Violić-Koprivec

2015-01-01

Full Text Available The paper discusses selected terms denoting crew members on Dubrovnik ships throughout the history. The titles of the most important crew members are analyzed based on the corpus of the 18th century documents, literary works, and technical literature. The goal is to determine which terms are typical of the Dubrovnik area, whether their meanings have become restricted or extended, and how they have disappeared or remained in use over the centuries. It is obvious that the importance of individual crew members and their positions changed with time. Their responsibilities occasionally overlapped, and certain terms for their positions coexisted as synonyms, either belonging to the standard or local, i.e. colloquial use. A comparative analysis has revealed some specific features of the Dubrovnik maritime terminology referring to the ship’s crew. The terms škrivan, nokjer, nostromo, pilot, gvardijan and dispensjer are lexemes specific for this area. This is confirmed by their use in literary works.

The Analysis for the Effect of Mixing Vane Shape on TDC

International Nuclear Information System (INIS)

Moon, Kang Hoon; Park, Ho Young; Kim, Kang Hoon; Park, Eung Jun; Suh, Jung Min

2011-01-01

The Thermal Diffusion Coefficient (TDC) is an input parameter to subchannel code, and it is required to predict local flow conditions in a PWR fuel bundle. TDC influences on the prediction of thermal interchange or mixing of thermal energy between the hot subchannel and interconnected adjacent subchannels. The thermal mixing term in the energy equation is generally represented in terms of a non-dimensional inverse Peclet number or TDC. The parameters associated with thermal mixing can be defined as Eq.(1): TDC =Pe x De/a (1) where: Pe : Inverse Peclet Number (dimensionless) = ε/ Va De : Equivalent hydraulic diameter, in. a : Lateral flow area between channels per unit length, in 2 /in ε : Mixing coefficient, in 2 /sec V : Velocity, in/sec TDC is an important factor to evaluate thermal performance. So, flow temperature maps were obtained from the 5x5 rod bundle test section to assess the thermal performance of corresponding fuels. The flow temperatures were measured by thermocouple at the end of heated length and the centroid of subchannel. There are two typical methods to arrange the hot and cold fuel rods as shown in Fig. 1. Configuration Fig. 1(b) is adopted in this work. This paper presents how to determine the TDC and verifies whether all TDC with the effect of mixing vane shape is valid with respect to current design value

An extended family suddenly confronted with a life-threatening hereditary arrhythmia

NARCIS (Netherlands)

Hendriks, K.S.W.H.; Van Langen, I.M.; Van Tintelen, J.P.; Grosfeld, F.J.M.; Wilde, A.A.M.; Ten Kroode, H.F.J.

2005-01-01

Objective. This exploratory study serves to illustrate the psychological impact on an extended family in the process of genetic counselling and testing for a potentially life-threatening arrhythmia, the long-QT syndrome (LQTS). Method. All members of the third generation and their partners (n=11)

An extended family suddenly confronted with a life-threatening hereditary arrhythmia

NARCIS (Netherlands)

Hendriks, K. S. W. H.; van Langen, I. M.; van Tintelen, J. P.; Grosfeld, F. J. M.; Wilde, A. A. M.; ten Kroode, H. F. J.

2005-01-01

This exploratory study serves to illustrate the psychological impact on an extended family in the process of genetic counselling and testing for a potentially life-threatening arrhythmia, the long-QT syndrome (LQTS). All members of the third generation and their partners (n=11) were interviewed, the

Numerical investigation on pressure fluctuations in centrifugal compressor with different inlet guide vanes pre-whirl angles

International Nuclear Information System (INIS)

Wang, Y C; Shi, M; Cao, S L; Li, Z H

2013-01-01

The pressure fluctuations in a centrifugal compressor with different inlet guide vanes (IGV) pre-whirl angles were investigated numerically, as well as the pre-stress model and static structural of blade. The natural frequency was evaluated by pre-stress model analysis. The results show that, the aero-dynamic pressure acting on blade surface is smaller than rotation pre-stress, which wouldn't result in large deformation of blade. The natural frequencies with rotation pre-stress are slightly higher than without rotation pre-stress. The leading mechanism of pressure fluctuations for normal conditions is the rotor-stator (IGVs) interaction, while is serious flow separations for conditions that are close to surge line. A few frequency components in spectra are close to natural frequency, which possibly result in resonant vibration if amplitude is large enough, which is dangerous for compressor working, and should be avoided

Computer Programme Library at Ispra: Service to IAEA Member States

International Nuclear Information System (INIS)

1974-01-01

In 1964, in view of the increasingly important role of computers in atomic energy, the Nuclear Energy Agency of the Organization for Economic Co-operation and Development established a Computer Programme Library (CPL) at Ispra, Italy. The original purpose of this Library, then consisting chiefly of programmes for reactor calculations, was to improve communication between the originators of the computer programmes and the scientists and engineers in Member States of the OECD who used them, thus furthering the efficient and economic use of the many large and expensive computers in the countries concerned. During the first few years of the Library's operation, a growing interest in its activities became evident in countries which were not members of the OECD. The Director General of the International Atomic Energy Agency, aware that such countries which were Member States of the IAEA could benefit from the Library's services, concluded an agreement with the Nuclear Energy Agency in 1967 to the effect that these services would be extended to all IAEA Member States. In March 1968, the Director General announced by circular letter that these services were available, and requested the governments of Member States that were not members of OECD to nominate establishments to participate in the activities of the Computer Programme Library. By August 1973, 32 such establishments were regularly using the services of the CPL

CFD simulation and validation of turbulent mixing in a rod bundle with vaned spacer grids based on LDV test

International Nuclear Information System (INIS)

Chen Xi; Li Songwei; Li Zhongchun; Du Sijia; Zhang Yu; Peng Huanhuan

2017-01-01

Spacer grids with mixing vanes are generally used in fuel assemblies of Pressurized Water Reactor (PWR), because that mixing vanes could enhance the lateral turbulent mixing in subchannels. Thus, heat exchangements are more efficient, and the value of departure from nucleate boiling (DNB) is greatly increased. Actually turbulent mixing is composed of two kinds of flows: swirling flow inside the subchannel and cross flow between subchannels. Swirling flow could induce mixing between hot water near the rod and cold water in the center of the subchannel, and may accelerate deviation of the bubbles from the rod surface. Besides, crossing flow help to mixing water between hot subchannels and cold subchannels, which impact relatively large flow area. As a result, how to accurately capture and how to predict the complicated mixing phenomenon are of great concernments. Recently many experimental studies has been conducted to provide detailed turbulent mixing in rod bundle, among which Laser Doppler Velocimetry method is widely used. With great development of Computational Fluid Dynamics, CFD has been validated as an analysis method for nuclear engineering, especially for single phase calculation. This paper presents the CFD simulation and validation of the turbulent mixing induced by spacer grid with mixing vanes in rod bundles. Experiment data used for validation came from 5 x 5 rod bundle test with LDV technology, which is organized by Science and Technology on Reactor System Design Technology Laboratory. A 5 x 5 rod bundle with two spacer grids were used. Each rod has dimension of 9.5 mm in outer diameter and distance between rods is 12.6 mm. Two axial bulk velocities were conducted at 3.0 m/s for high Reynolds number and 1.0 m/s for low Reynolds number. Working pressure was 1.0 bar, and temperature was about 25degC. Two different distances from the downstream of the mixing spacer grid and one from upstream were acquired. Mean axial velocities and turbulent intensities

Surface Temperature Measurements from a Stator Vane Doublet in a Turbine Engine Afterburner Flame Using a YAG:Tm Thermographic Phosphor

Science.gov (United States)

Eldridge, J. I.; Walker, D. G.; Gollub, S. L.; Jenkins, T. P.; Allison, S. W.

2015-01-01

Luminescence-based surface temperature measurements were obtained from a YAG:Tm-coated stator vane doublet exposed to the afterburner flame of a J85 test engine at University of Tennessee Space Institute (UTSI). The objective of the testing was to demonstrate that reliable surface temperatures based on luminescence decay of a thermographic phosphor producing short-wavelength emission could be obtained from the surface of an actual engine component in a high gas velocity, highly radiative afterburner flame environment. YAG:Tm was selected as the thermographic phosphor for its blue emission at 456 nm (1D23F4 transition) and UV emission at 365 nm (1D23H6 transition) because background thermal radiation is lower at these wavelengths, which are shorter than those of many previously used thermographic phosphors. Luminescence decay measurements were acquired using a probe designed to operate in the afterburner flame environment. The probe was mounted on the sidewall of a high-pressure turbine vane doublet from a Honeywell TECH7000 turbine engine coated with a standard electron-beam physical vapor deposited (EB-PVD) 200-m-thick TBC composed of yttria-stabilized zirconia (YSZ) onto which a 25-m-thick YAG:Tm thermographic phosphor layer was deposited by solution precursor plasma spray (SPPS). Spot temperature measurements were obtained by measuring luminescence decay times at different afterburner power settings and then converting decay time to temperature via calibration curves. Temperature measurements using the decays of the 456 and 365 nm emissions are compared. While successful afterburner environment measurements were obtained to about 1300C with the 456 nm emission, successful temperature measurements using the 365 nm emission were limited to about 1100C due to interference by autofluorescence of probe optics at short decay times.

Extended Collective Licenses and the Nordic Experience - It's a Hybrid but is it a VOLVO or a Lemon?

DEFF Research Database (Denmark)

Riis, Thomas; Schovsbo, Jens Hemmingsen

An extended collective license is a legal model whereby the binding effect of a collective agreement between an organization of copyright holders and a user of copyrightable works is extended to right holders who are not members of the organization. Such models have been used for rights clearance...

Zero-gravity Mean Free Surface Curvature of a Confined Liquid in a Radially-Vaned Container

Science.gov (United States)

Chen, Yongkang; Callahan, Michael; Weislogel, Mark

2013-01-01

A variety of increasingly intricate container geometries are under consideration for the passive manipulation of liquids aboard spacecraft where the impact of gravity may be neglected. In this study we examine the mean curvature of a liquid volume confined within a radial array of disconnected vanes of infinite extent. This particular geometry possesses a number of desirable characteristics relevant to waste water treatment aboard spacecraft for life support. It is observed that under certain conditions the slender shape of the free surface approaches an asymptote, which can be predicted analytically using new hybrid boundary conditions proposed herein. This contribution represents possibly the final extension of what has been referred to as the method of de Lazzer et al. (1996). The method enables the integration of the Young-Laplace equation over a domain with its boundaries, including the wetted portion of the solid boundaries, symmetry planes, and circular arcs representing free surfaces at the center plane of the liquid body. Asymptotic solutions at several limits are obtained and the analysis is confirmed with numerical computations.

Extending Social Learning Theory to Explain Victimization Among Gang and Ex-Gang Offenders.

Science.gov (United States)

Gagnon, Analisa

2018-03-01

This study is among the first to extend and test social learning theory's ability to understand property and violent victimization. It specifically tests whether aspects of definitions, differential reinforcement, and differential association/modeling can explain the three types of victimization of gang members: actual experience, perception of likelihood, and fear. The sample consists of over 300 male and female gang members incarcerated in jails throughout Florida. The results show that all three types of victimization can be explained by the three aspects of social learning theory.

Tension stiffening in partially prestressed concrete flexural members

International Nuclear Information System (INIS)

Oukaili, K. N.

2000-01-01

Concrete tensile strength is not being zero, cracking does not extend to the neutral axis as assumed in standard cracked section analysis. In addition, un cracked concrete, which exists above the crack tip in the tension zone, contributes to the stiffness of the member. This paper discusses the influence of concrete tensile stress below the neut ural axis position at the cracked section on the tension stiffening phenomenon and deflection of progressively cracking partially prestressed concrete flexural members. The computation of the neutral axis location, which takes into consideration the effect of concrete in tension, can be achieved by solving iteratively tow simultaneous equation derived from forces and moments equilibrium, strain compatibility and linear stress - strain relationship in concrete across the section depth. Once the section depth after cracking is known, it can be used to calculate the effective moment of inertia for deflection analysis. (author). 13 refs., 3 figs., 1 table

Airfoil shape for a turbine nozzle

Science.gov (United States)

Burdgick, Steven Sebastian; Patik, Joseph Francis; Itzel, Gary Michael

2002-01-01

A first-stage nozzle vane includes an airfoil having a profile according to Table I. The annulus profile of the hot gas path is defined in conjunction with the airfoil profile and the profile of the inner and outer walls by the Cartesian coordinate values given in Tables I and II, respectively. The airfoil is a three-dimensional bowed design, both in the airfoil body and in the trailing edge. The airfoil is steam and air-cooled by flowing cooling mediums through cavities extending in the vane between inner and outer walls.

Extended Collective Licenses and the Nordic Experience - It’s a Hybrid but is It a Volvo or a Lemon

DEFF Research Database (Denmark)

Schovsbo, Jens Hemmingsen; Riis, Thomas

2010-01-01

An extended collective license is a legal model whereby the binding effect of a collective agreement between an organization of copyright holders and a user of copyrightable works is extended to right holders who are not members of the organization. Such models have been used for rights clearance...

Rotor boundary layer development with inlet guide vane (IGV) wake impingement

Science.gov (United States)

Jia, Lichao; Zou, Tengda; Zhu, Yiding; Lee, Cunbiao

2018-04-01

This paper examines the transition process in a boundary layer on a rotor blade under the impingement of an inlet guide vane wake. The effects of wake strengths and the reduced frequency on the unsteady boundary layer development on a low-speed axial compressor were investigated using particle image velocimetry. The measurements were carried out at two reduced frequencies (fr = fIGVS0/U2i, fr = 1.35, and fr = 0.675) with the Reynolds number, based on the blade chord and the isentropic inlet velocity, being 97 500. At fr = 1.35, the flow separated at the trailing edge when the wake strength was weak. However, the separation was almost totally suppressed as the wake strength increased. For the stronger wake, both the wake's high turbulence and the negative jet behavior of the wake dominated the interaction between the unsteady wake and the separated boundary layer on the suction surface of the airfoil. The boundary layer displacement thickened first due to the negative jet effect. Then, as the disturbances developed underneath the wake, the boundary layer thickness reduced gradually. The high disturbance region convected downstream at a fraction of the free-stream velocity and spread in the streamwise direction. The separation on the suction surface was suppressed until the next wake's arrival. Because of the long recovery time at fr = 0.675, the boundary layer thickened gradually as the wake convected further downstream and finally separated due to the adverse pressure gradient. The different boundary layer states in turn affected the development of disturbances.

Analysis on regulation strategies for extending service life of hydropower turbines

Science.gov (United States)

Yang, W.; Norrlund, P.; Yang, J.

2016-11-01

Since a few years, there has been a tendency that hydropower turbines experience fatigue to a greater extent, due to increasingly more regulation movements of governor actuators. The aim of this paper is to extend the service life of hydropower turbines, by reasonably decreasing the guide vane (GV) movements with appropriate regulation strategies, e.g. settings of PI (proportional-integral) governor parameters and controller filters. The accumulated distance and number of GV movements are the two main indicators of this study. The core method is to simulate the long-term GV opening of Francis turbines with MATLAB/Simulink, based on a sequence of one-month measurements of the Nordic grid frequency. Basic theoretical formulas are also discussed and compared to the simulation results, showing reasonable correspondence. Firstly, a model of a turbine governor is discussed and verified, based on on-site measurements of a Swedish hydropower plant. Then, the influence of governor parameters is discussed. Effects of different settings of controller filters (e.g. dead zone, floating dead zone and linear filter) are also examined. Moreover, a change in GV movement might affect the quality of the frequency control. This is also monitored via frequency deviation characteristics, determined by elementary simulations of the Nordic power system. The results show how the regulation settings affect the GV movements and frequency quality, supplying suggestions for optimizing the hydropower turbine operation for decreasing the wear and tear.

Plane stress analysis of wood members using isoparametric finite elements, a computer program

Science.gov (United States)

Gary D. Gerhardt

1983-01-01

A finite element program is presented which computes displacements, strains, and stresses in wood members of arbitrary shape which are subjected to plane strain/stressloading conditions. This report extends a program developed by R. L. Taylor in 1977, by adding both the cubic isoparametric finite element and the capability to analyze nonisotropic materials. The...

Extended family childcare arrangements in a context of AIDS: collapse or adaptation?

Science.gov (United States)

Mathambo, Vuyiswa; Gibbs, Andy

2009-01-01

Families are subjected to a number of social, economic, political and demographic challenges. In recent years, the AIDS epidemic has constituted a major challenge for already poor families due to its wide reaching social, economic and health consequences. The devastating consequence of HIV and AIDS is being seen through the prolonged illness and death of family members of prime working age which impacts on family livelihoods and the ability to provide for and protect its members. This paper forms part of a review - commissioned by the Joint Learning Initiative on Children and HIV/AIDS - of qualitative studies of how families in southern Africa have changed, and are changing, as a result of the impact of HIV and AIDS. This paper presents results of how extended family childcare arrangements are changing as a result of the AIDS epidemic. In a southern African context, family denotes a wider array of relations than biological parents and their children - with children growing up amongst a multitude of relations sharing responsibility for their care and upbringing (Chirwa, 2002; Verhoef, 2005). Recently, there has been growing interest in the capacity of the extended family to care for the increasing number of children whose parents have died. However, literature on the role of the extended family in caring for orphaned children remains contradictory. One approach - the social rupture thesis (Chirwa, 2002) - suggests that the extended family network is collapsing under the strain of AIDS. On the other hand, families are portrayed as resilient and dynamic entities which are adapting their systems of childcare in response to the epidemic (Kuo,2007). In line with Abebe and Aase (2007) and Adams, Cekan, and Sauerborn (1998), this paper proposes a continuum of survival rather than a polarisation of extended family childcare arrangements.

Off-design performance loss model for radial turbines with pivoting, variable-area stators

Science.gov (United States)

Meitner, P. L.; Glassman, A. J.

1980-01-01

An off-design performance loss model was developed for variable stator (pivoted vane), radial turbines through analytical modeling and experimental data analysis. Stator loss is determined by a viscous loss model; stator vane end-clearance leakage effects are determined by a clearance flow model. Rotor loss coefficient were obtained by analyzing the experimental data from a turbine rotor previously tested with six stators having throat areas from 20 to 144 percent of design area and were correlated with stator-to-rotor throat area ratio. An incidence loss model was selected to obtain best agreement with experimental results. Predicted turbine performance is compared with experimental results for the design rotor as well as with results for extended and cutback versions of the rotor. Sample calculations were made to show the effects of stator vane end-clearance leakage.

Stratigraphy, artefact industries and hominid associations for Sterkfontein, member 5.

Science.gov (United States)

Kuman, K; Clarke, R J

2000-06-01

A revised stratigraphy for the early hominid site of Sterkfontein (Gauteng Province, South Africa) reveals a complex distribution of infills in the main excavation area between 2.8 and 1.4 m.y.a, as well as deposits dating to the mid to late Pleistocene. New research now shows that the Member 4 australopithecine breccia (2.8-2.6 Ma) extends further west than was previously thought, while a late phase of Member 4 is recognized in a southern area. The artefact-bearing breccias were defined sedimentologically as Member 5, but one supposed part of these younger breccias, the StW 53 infill, lacks in situ stone tools, although it does appear to post-date 2.6 Ma when artefacts first appear in the archaeological record. The StW 53 hominid, previously referred to Homo habilis, is here argued to be Australopithecus. The first artefact-bearing breccia of Member 5 is the Oldowan Infill, estimated at 2-1.7 Ma. It occupies a restricted distribution in Member 5 east and contains an expedient, flake-based tool industry associated with a few fossils of Paranthropos robustus. An enlarged cave opening subsequently admitted one or more Early Acheulean infills associated in Member 5 west with Homo ergaster. The artefacts attest to a larger site accumulation between ca. 1.7 and 1.4 Ma, with more intensive use of quartzite over quartz and a subtle but important shift to large flakes and heavier-duty tools. The available information on palaeoenvironments is summarized, showing an overall change from tropical to sub-tropical gallery forest, forest fringe and woodland conditions in Member 4 to more open woodland and grassland habitats in the later units, but with suggestions of a wet localized topography in the Paranthropus -bearing Oldowan Infill. Copyright 2000 Academic Press.

A Study of Performance Output of a Multivane Air Engine Applying Optimal Injection and Vane Angles

Directory of Open Access Journals (Sweden)

Bharat Raj Singh

2012-01-01

Full Text Available This paper presents a new concept of the air engine using compressed air as the potential power source for motorbikes, in place of an internal combustion engine. The motorbike is proposed to be equipped with an air engine, which transforms the energy of the compressed air into mechanical motion energy. A mathematical model is presented here, and performance evaluation is carried out on an air-powered novel air turbine engine. The maximum power output is obtained as 3.977 kW (5.50 HP at the different rotor to casing diameter ratios, optimal injection angle 60°, vane angle 45° for linear expansion (i.e., at minimum air consumption when the casing diameter is kept 100 mm, at injection pressure 6 bar (90 psi and speed of rotation 2500 rpm. A prototype air engine is built and tested in the laboratory. The experimental results are also seen much closer to the analytical values, and the performance efficiencies are recorded around 70% to 95% at the speed of rotation 2500–3000 rpm.

Active unsteady aerodynamic suppression of rotating stall in an incompressible flow centrifugal compressor with vaned diffuser

Science.gov (United States)

Lawless, Patrick B.; Fleeter, Sanford

1991-01-01

A mathematical model is developed to analyze the suppression of rotating stall in an incompressible flow centrifugal compressor with a vaned diffuser, thereby addressing the important need for centrifugal compressor rotating stall and surge control. In this model, the precursor to to instability is a weak rotating potential velocity perturbation in the inlet flow field that eventually develops into a finite disturbance. To suppress the growth of this potential disturbance, a rotating control vortical velocity disturbance is introduced into the impeller inlet flow. The effectiveness of this control is analyzed by matching the perturbation pressure in the compressor inlet and exit flow fields with a model for the unsteady behavior of the compressor. To demonstrate instability control, this model is then used to predict the control effectiveness for centrifugal compressor geometries based on a low speed research centrifugal compressor. These results indicate that reductions of 10 to 15 percent in the mean inlet flow coefficient at instability are possible with control waveforms of half the magnitude of the total disturbance at the inlet.

Effects of grid spacer with mixing vane on entrainments and depositions in two-phase annular flows

Directory of Open Access Journals (Sweden)

Akimaro Kawahara

2015-06-01

Full Text Available The effects of mixing vanes (MVs attached to a grid spacer on the characteristics of air–water annular flows were experimentally investigated. To know the effects, a grid spacer with or without MV was inserted in a vertical circular pipe of 16-mm internal diameter. For three cases (i.e., no spacer, spacer without MV, and spacer with MV, the liquid film thickness, liquid entrainment fraction, and deposition rate were measured by the constant current method, single liquid film extraction method, and double liquid film extraction method, respectively. The MVs significantly promote the re-deposition of liquid droplets in the gas core flow into the liquid film on the channel walls. The deposition mass transfer coefficient is three times higher for the spacer with MV than for the spacer without MV, even for cases 0.3-m downstream from the spacer. The liquid film thickness becomes thicker upstream and downstream for the spacer with MV, compared with the thickness for the spacer without MV and for the case with no spacer.

International bowel function extended spinal cord injury data set

DEFF Research Database (Denmark)

Krogh, K; Perkash, I; Stiens, S A

2008-01-01

and the ASIA Board. Relevant and interested scientific and professional organizations and societies (around 40) were also invited to review the data set and it was posted on the ISCoS and ASIA websites for 3 months to allow comments and suggestions. The ISCoS Scientific Committee, ISCoS Council and ASIA Board......STUDY DESIGN: International expert working group.Objective:To develop an International Bowel Function Extended Spinal Cord Injury (SCI) Data Set presenting a standardized format for the collection and reporting of an extended amount of information on bowel function. SETTING: Working group...... consisting of members appointed by the American Spinal Injury Association (ASIA) and the International Spinal Cord Society (ISCoS). METHODS: A draft prepared by the working group was reviewed by Executive Committee of the International SCI Standards and Data Sets and later by the ISCoS Scientific Committee...

75 FR 22641 - Order Extending and Modifying Temporary Conditional Exemptions Under the Securities Exchange Act...

Science.gov (United States)

2010-04-29

... those positions. Under Eurex customer clearing, the clearing relationship and Eurex's guarantee extends... member default. The customer relationship would be governed by an agreement between the customer and the... risks inherent in the CDS market, and thus can help mitigate potential systemic impact. We have...

Why the EU-15 Maintains Higher CIT Rates than the New Member States?

Directory of Open Access Journals (Sweden)

Karpowicz Andrzej

2014-11-01

Full Text Available The European Union is not a homogenous area. This lack of homogeneity extends to taxes, which vary across jurisdictions. On average, Western Europe imposes significantly higher taxes on capital than New Member States, which joined the Community in 2004 and 2007. Often this fact is simply taken for granted. However, there are several arguments that can explain this variance. Although several of these arguments are well known and have been researched, they have not been assessed in combination, or used in a comparative analysis of corporate income tax (CIT rates between EU member states. Because of interest in harmonizing CIT throughout the EU, the roots of divergent CIT is of particular and timely value. Therefore, this article we attempts to demonstrate the differences in CIT rates in the EU-15 and New Member States. In so doing the general characteristics of these country grouping is identified, and then discussed in the context of the taxation theory.

Extending the moral economy beyond households: Gendered livelihood strategies of single migrant women in Accra, Ghana

NARCIS (Netherlands)

Tufuor, T.; Niehof, A.; Sato, C.; Horst, van der H.M.

2015-01-01

This article highlights how single migrant women (SMW) from rural northern Ghana generate livelihoods through the adoption of both market and non-market based strategies by extending and then prioritising moral obligations to community members beyond their immediate households instead of focusing on

Minority faculty members' resilience and academic productivity: are they related?

Science.gov (United States)

Cora-Bramble, Denice; Zhang, Kehua; Castillo-Page, Laura

2010-09-01

To explore whether there is a relationship between resilience and academic productivity of minority faculty members in U.S. academic health centers. For the purposes of the study, the authors defined academic productivity as peer-reviewed and non-peer-reviewed publications, grants, and academic promotion. In 2007, the authors simultaneously collected quantitative and qualitative data by using a triangulation (mixed-method) design. Past participants in the Association of American Medical Colleges' Minority Faculty Career Development Seminar completed the Web-based 70-item Personal Resilience Questionnaire (PRQ). In addition, two focus groups were conducted with past seminar participants. Seventy-four minority faculty members completed the PRQ, and 15 participated in the two focus groups. The quantitative data showed a positive correlation between demographic, educational, and academic productivity variables and certain resilience subscale scores. Common themes that emerged from the qualitative data were categorized under four major domains: existing barriers to academic advancement, internal protective factors or cultural buffers, external institutional or environmental facilitators, and necessary attributes for ensuring academic productivity and advancement. Certain resilience subscales showed correlation with academic productivity of minority faculty members, and specific personal and/or cultural characteristics were identified as enablers. Minority faculty members may benefit from skill development and coaching that extends beyond the traditional scope of faculty development programs and that specifically targets modifiable resilience characteristics. Additional research is needed, but such nontraditional, resilience-centered intervention strategies may positively affect the advancement of minority faculty in academic medicine.

Rod cluster having improved vane configuration

International Nuclear Information System (INIS)

Shockling, L.A.; Francis, T.A.

1989-01-01

This patent describes a pressurized water reactor vessel, the vessel defining a predetermined axial direction of the flow of coolant therewithin and having plural spider assemblies supporting, for vertical movement within the vessel, respective clusters of rods in spaced, parallel axial relationship, parallel to the predetermined axial direction of coolant flow, and a rod guide for each spider assembly and respective cluster of rods. The rod guide having horizontally oriented support plates therewithin, each plate having an interior opening for accommodating axial movement therethrough of the spider assembly and respective cluster of rods. The opening defining plural radially extending channels and corresponding parallel interior wall surfaces of the support plate

Effects of Radial Gap Ratio between Impeller and Vaned Diffuser on Performance of Centrifugal Compressors

Directory of Open Access Journals (Sweden)

Mohammadjavad Hosseini

2017-07-01

Full Text Available A high-performance centrifugal compressor is needed for numerous industry applications nowadays. The radial gap ratio between the impeller and the diffuser vanes plays an important role in the improvement of the compressor performance. In this paper, the effects of the radial gap ratio on a high-pressure ratio centrifugal compressor are investigated using numerical simulations. The performance and the flow field are compared for six different radial gap ratios and five rotational speeds. The minimal radial gap ratio was 1.04 and the maximal was 1.14. Results showed that reducing the radial gap ratio decreases the choke mass flow rate. For the tip-speed Mach number (impeller inlet with Mu < 1, the pressure recovery and the loss coefficients are not sensitive to the radial gap ratio. However, for Mu ≥ 1, the best radial gap ratio is 1.08 for the pressure recovery and the loss coefficients. Furthermore, the impeller pressure ratio and efficiency are reduced by increasing the radial gap ratio. Finally, the compressor efficiency was compared for different radial gap ratios. For Mu < 1, the radial gap ratio does not have noticeable effects. In comparison, the radial gap ratio of 1.08 has the best performance for Mu ≥ 1.

Experimental evidence of the thermal effect of lubricating oil sprayed in sliding-vane air compressors

Directory of Open Access Journals (Sweden)

Gianluca Valenti

2014-11-01

Full Text Available A way to increase the efficiency of positive-displacement air compressor is spraying the lube oil to exploit it not only as lubricating and sealing agent but also as thermal ballast. This work seeks the experimental evidence in sliding-vane compressors by measuring the air standard volume flow rate and the electrical power input of three diverse configurations. The first configuration, taken as the reference, employs a conventional injection system comprising calibrated straight orifices. The other two, referred to as advanced, adopt smaller orifices and pressure-swirl full-cone nozzles designed for the purpose; the third configuration utilizes a pump to boost the oil pressure. The laser imagining technique shows that the nozzles generate sprays that break-up within a short distance into spherical droplets, ligaments, ramifications and undefined structures. Tests on the packaged compressors reveal that the advanced configurations provide almost the same air flow rate while utilizing half of the oil because the sprays generate a good sealing. Moreover, the sprayed oil is acting as a thermal ballast because the electrical input is reduced by 3.5% and 3.0%, respectively, if the pump is present or not , while the specific energy requirement, accounting for the slightly reduced air flow, by 2.4% and 2.9%, respectively.

The Text of the Agreement of 8 July Extending the Asian Regional Co-Operative Project on Food Irradiation. Extension Agreement

International Nuclear Information System (INIS)

1983-12-01

The text of the Agreement to Extend the Agreement of 23 May 1980 Establishing the Asian Regional Co-operative Project on Food Irradiation within the framework of the Regional Co-operative Agreement for Research, Development and Training Related to Nuclear Science and Technology of 1972, as extended in 1977 and in 1982, is reproduced herein for the information of all Members

A Non-Member Spouse's Entitlement To The Member's Pension Interest

Directory of Open Access Journals (Sweden)

Motseotsile Clement Marumoagae

2014-12-01

Full Text Available It is important that married couples seek legal advice with regard to the assets falling within their joint estate, more particularly their retirement benefits. This article reflects on the entitlement (if any of non-member spouses to their spouses' retirement fund benefits. Pension benefits can be due before, during or after divorce, and parties to the marriage should be aware of their rights with regard to the accruing pension benefits of their spouses. While it is settled law that non-member spouses are entitled to receive a portion of their member spouses' pension benefits (known as "pension interest" immediately on divorce, it is not particularly clear whether non-member spouses are also entitled to receive the same before or sometime after divorce. In this article I provide a contextual understanding of the entitlements (if any which spouses or former spouses of members of pension funds have on such member spouses' retirement benefits. Furthermore, it shown in this article that various divisions of South African High Courts have been inconsistent in how they have approached the issue of the pension interest between divorcing spouses or divorced ex-spouses.

TACT1- TRANSIENT THERMAL ANALYSIS OF A COOLED TURBINE BLADE OR VANE EQUIPPED WITH A COOLANT INSERT

Science.gov (United States)

Gaugler, R. E.

1994-01-01

As turbine-engine core operating conditions become more severe, designers must develop more effective means of cooling blades and vanes. In order to design reliable, cooled turbine blades, advanced transient thermal calculation techniques are required. The TACT1 computer program was developed to perform transient and steady-state heat-transfer and coolant-flow analyses for cooled blades, given the outside hot-gas boundary condition, the coolant inlet conditions, the geometry of the blade shell, and the cooling configuration. TACT1 can analyze turbine blades, or vanes, equipped with a central coolant-plenum insert from which coolant-air impinges on the inner surface of the blade shell. Coolant-side heat-transfer coefficients are calculated with the heat transfer mode at each station being user specified as either impingement with crossflow, forced convection channel flow, or forced convection over pin fins. A limited capability to handle film cooling is also available in the program. The TACT1 program solves for the blade temperature distribution using a transient energy equation for each node. The nodal energy balances are linearized, one-dimensional, heat-conduction equations which are applied at the wall-outer-surface node, at the junction of the cladding and the metal node, and at the wall-inner-surface node. At the mid-metal node a linear, three-dimensional, heat-conduction equation is used. Similarly, the coolant pressure distribution is determined by solving the set of transfer momentum equations for the one-dimensional flow between adjacent fluid nodes. In the coolant channel, energy and momentum equations for one-dimensional compressible flow, including friction and heat transfer, are used for the elemental channel length between two coolant nodes. The TACT1 program first obtains a steady-state solution using iterative calculations to obtain convergence of stable temperatures, pressures, coolant-flow split, and overall coolant mass balance. Transient

Leader-member exchange (LMX) and culture: a meta-analysis of correlates of LMX across 23 countries.

Science.gov (United States)

Rockstuhl, Thomas; Dulebohn, James H; Ang, Soon; Shore, Lynn M

2012-11-01

This study extends leader-member exchange (LMX) research by meta-analyzing the role of national culture in moderating relationships between LMX and its correlates. Results based on 282 independent samples (N = 68,587) from 23 countries and controlling for extreme response style differences indicate that (a) relationships of LMX with organizational citizenship behavior, justice perceptions, job satisfaction, turnover intentions, and leader trust are stronger in horizontal-individualistic (e.g., Western) contexts than in vertical-collectivistic (e.g., Asian) contexts; and (b) national culture does not affect relationships of LMX with task performance, organizational commitment, and transformational leadership. These findings highlight that although members are universally sensitive to how their leaders treat them, members' responses in Asian contexts may also be influenced by collective interests and role-based obligations. (c) 2012 APA, all rights reserved.

Members of the Agency

International Nuclear Information System (INIS)

2007-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.63) is Palau which deposited its Instrument of Acceptance of the Statute on 2 March 2007. The Attachment hereto shows the dates on which the present 144 Member States became Members [fr

Members of the Agency

International Nuclear Information System (INIS)

2007-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.63) is Palau which deposited its Instrument of Acceptance of the Statute on 2 March 2007. The Attachment hereto shows the dates on which the present 144 Member States became Members [es

Computational study: The influence of omni-directional guide vane on the flow pattern characteristic around Savonius wind turbine

Science.gov (United States)

Wicaksono, Yoga Arob; Tjahjana, D. D. D. P.

2017-01-01

Standart Savonius wind turbine have a low performance such as low coefficient of power and low coefficient of torque compared with another type of wind turbine. This phenomenon occurs because the wind stream can cause the negative pressure at the returning rotor. To solve this problem, standard Savonius combined with Omni Directional Guide Vane (ODGV) proposed. The aim of this research is to study the influence of ODGV on the flow pattern characteristic around of Savonius wind turbine. The numerical model is based on the Navier-Stokes equations with the standard k-ɛ turbulent model. This equation solved by a finite volume discretization method. This case was analyzed by commercial computational fluid dynamics solver such as SolidWorks Flow Simulations. Simulations were performed at the different wind directions; there are 0°, 30°,60° at 4 m/s wind speed. The numerical method validated with the past experimental data. The result indicated that the ODGV able to augment air flow to advancing rotor and decrease the negative pressure in the upstream of returning rotor compared to the bare Savonius wind turbine.

Preparation, melting behavior and thermal stability of poly(lactic acid)/poly(propylene carbonate) blends processed by vane extruder

Energy Technology Data Exchange (ETDEWEB)

Zou, Wei, E-mail: zw55624@163.com; Chen, Rongyuan; Zhang, Haichen; Qu, Jinping, E-mail: jpqu@scut.edu.cn [National Engineering Research Center of Novel Equipment for Polymer Processing, South China University of Technology, Guangzhou 510640 (China)

2016-03-09

Poly (lactic acid) (PLA)/Poly (propylene carbonate) (PPC) blends were prepared by vane extruder which is a type of novel polymer processing extruder based on elongation force field. Scanning electron microscope (SEM), differential scanning calorimetry (DSC) and thermogravimetric (TG) were used respectively to analyze the compatibility, the melting behavior and thermal stability properties of PLA/PPC blends affected by the different content of PPC. The results showed that with the increase of the PPC content, the glass transition temperature of PLA was reduced, and the glass transition temperature of PPC was increased, which indicated that PLA and PPC had partial compatibility. The cold crystallization temperature of PLA increased with the increase of the PPC content, which showed that PPC hindered the cold crystallization process of PLA. The addition of PPC had little impact on the melting process of PLA, and the melting temperature of PLA was almost kept the same value. Thermogravimetric analysis showed that the thermal stability of PPC was worse than that of PLA, the addition of PPC reduced the thermal stability of PLA.

Extended lanthanide-transition metal arrays with cyanide bridges: syntheses, structures, and catalytic applications

International Nuclear Information System (INIS)

Liu Shengming; Poplaukhin, Pavel; Ding Errun; Plecnik, Christine E.; Chen Xuenian; Keane, Mark A.; Shore, Sheldon G.

2006-01-01

Systematic synthetic procedures produced several different structural types of extended lanthanide-transition metal (group 10) complexes with cyanide bridges. Of these, one-dimensional ladder arrays containing a Yb-Pd combination have been converted to bimetallic heterogeneous catalysts on an oxide (SiO 2 ) surface that is more effective than supported Pd alone. Two lanthanide-Cu(I) complexes have been prepared. One type, an inclusion complex consists of lanthanide(III) cations encapsulated in the pockets of a three-dimensional anionic array that contains Cu(I)-CN-Cu(I) bridges. The second type, an extended layer complex, consists of joined five-membered rings in a 'tile-like' pattern with Ln-CN-Cu and Cu-CN-Cu bridges

Does formal mentoring for faculty members matter? A survey of clinical faculty members.

Science.gov (United States)

Mylona, Elza; Brubaker, Linda; Williams, Valerie N; Novielli, Karen D; Lyness, Jeffrey M; Pollart, Susan M; Dandar, Valerie; Bunton, Sarah A

2016-06-01

Mentoring relationships, for all medical school faculty members, are an important component of lifelong development and education, yet an understanding of mentoring among medical school clinical faculty members is incomplete. This study examined associations between formal mentoring relationships and aspects of faculty members' engagement and satisfaction. It then explored the variability of these associations across subgroups of clinical faculty members to understand the status of mentoring and outcomes of mentoring relationships. The authors hypothesised that academic clinical faculty members currently in formal mentoring relationships experience enhanced employee engagement and satisfaction with their department and institution. Medical school faculty members at 26 self-selected USA institutions participated in the 2011-2014 Faculty Forward Engagement Survey. Responses from clinical faculty members were analysed for relationships between mentoring status and perceptions of engagement by faculty members. Of the 11 953 clinical faculty respondents, almost one-third reported having a formal mentoring relationship (30%; 3529). Most mentored faculty indicated the relationship was important (86%; n = 3027), and over three-fourths were satisfied with their mentoring experience (77%; n = 2722). Mentored faculty members across ranks reported significantly higher levels of satisfaction and more positive perceptions of their roles in the organisation. Faculty members who were not receiving mentoring reported significantly less satisfaction with their workplace environment and lower overall satisfaction. Mentored clinical faculty members have significantly greater satisfaction with their department and institution. This multi-institutional study provides evidence that fostering mentoring opportunities may facilitate faculty members' satisfaction and engagement, which, in turn, may help medical schools retain high-quality faculty staff committed to the multidimensional

Numerical simulation of air flow through turbocharger compressors with dual volute design

Energy Technology Data Exchange (ETDEWEB)

Jiao, Kui; Li, Xianguo; Wu, Hao [Department of Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo, ON (Canada); Sun, Harold; Schram, Tim [Ford Motor Company, Dearborn, MI 48126 (United States); Krivitzky, Eric; Larosiliere, Louis M. [Concepts NREC, White River Junction, VT 05001 (United States)

2009-11-15

In this paper, turbocharger centrifugal compressors with dual volute design were investigated by using Computational Fluid Dynamics (CFD) method. The numerical simulation focused on the air flow from compressor impeller inlet to volute exit, and the overall performance level and range are predicted. The numerical investigation revealed that the dual volute design could separate the compressor into two operating regions: ''high efficiency'' and ''low efficiency'' regions with different air flow characteristics, and treating these two regions separately with dual diffuser design showed extended stable operating range and improved efficiency by comparing with conventional single volute design. The ''dual sequential volute'' concept also showed the potential to further extend the stable operating range by closing one of the volutes at low air flow rates. Furthermore, by comparing with other alternate designs such as variable diffuser vanes and variable inlet guide vanes, the operation of the dual sequential volute also features relatively simple control and calibration. (author)

Extended suicide with a pet.

Science.gov (United States)

Cooke, Brian K

2013-01-01

The combination of the killing of a pet and a suicide is a perplexing scenario that is largely unexplored in the literature. Many forensic psychiatrists and psychologists may be unaccustomed to considering the significance of the killing of a pet. The subject is important, however, because many people regard their pets as members of their family. A case is presented of a woman who killed her pet dog and herself by carbon monoxide poisoning. The purpose of this article is to provide an initial exploration of the topic of extended suicide with a pet. Forensic mental health evaluations may have a role in understanding the etiology of this event and in opining as to the culpability of individuals who attempt to or successfully kill a pet and then commit suicide. Because the scientific literature is lacking, there is a need to understand this act from a variety of perspectives. First, a social and anthropological perspective will be presented that summarizes the history of the practice of killing of one's pet, with a focus on the ancient Egyptians. A clinical context will examine what relationship animals have to mental illness. A vast body of existing scientific data showing the relevance of human attachment to pets suggests that conclusions from the phenomena of homicide-suicide and filicide-suicide are applicable to extended suicide with a pet. Finally, recommendations will be proposed for both clinical and forensic psychiatrists faced with similar cases.

Transition Process from Diffuser Stall to Stage Stall in a Centrifugal Compressor with a Vaned Diffuser

Directory of Open Access Journals (Sweden)

Nobumichi Fujisawa

2017-01-01

Full Text Available The transition process from a diffuser rotating stall to a stage stall in a centrifugal compressor with a vaned diffuser was investigated by experimental and numerical analyses. From the velocity measurements, it was found that the rotating stall existed on the shroud side of the diffuser passage in the off-design flow condition. The numerical results revealed the typical vortical structure of the diffuser stall. The diffuser stall cell was caused by the systematic vortical structure which consisted of the tornado-type vortex, the longitudinal vortex at the shroud/suction surface corner (i.e., leading edge vortex (LEV, and the vortex in the throat area of the diffuser passages. Furthermore, the stage stall, which rotated within both the impeller and diffuser passages, occurred instead of the diffuser stall as the mass flow rate was decreased. According to the velocity measurements at the diffuser inlet, the diffuser stall which rotated on the shroud side was shifted to the hub side. Then, the diffuser stall moved into the impeller passages and formed the stage stall. Therefore, the stage stall was caused by the development of the diffuser stall, which transferred from the shroud side to the hub side in the vaneless space and expanded to the impeller passages.

The design, simulation and testing of an urban vertical axis wind turbine with the omni-direction-guide-vane

International Nuclear Information System (INIS)

Chong, W.T.; Fazlizan, A.; Poh, S.C.; Pan, K.C.; Hew, W.P.; Hsiao, F.B.

2013-01-01

Graphical abstract: Solar energy, renewable energy, urban wind energy, environment, augmented wind turbine. Highlights: ► A system for on-site wind–solar hybrid power generation and rain water collection. ► The omni-direction-guide-vane (ODGV) overcomes the weak wind and turbulence conditions in urban areas. ► The ODGV improves the wind turbine performance by speeding-up and guiding the wind. ► The ODGV is designed to blend into the building architecture with safety enhancement. ► The wind tunnel test and CFD simulation results are presented. - Abstract: A novel omni-direction-guide-vane (ODGV) that surrounds a vertical axis wind turbine (VAWT) is designed to improve the wind turbine performance. Wind tunnel testing was performed to evaluate the performance of a 5-bladed (Wortmann FX63-137 airfoil) H-rotor wind turbine, with and without the integration of the ODGV. The test was conducted using a scaled model turbine which was constructed to simulate the VAWT enclosed by the ODGV placed on a building. The VAWT shows an improvement on its self-starting behavior where the cut-in speed was reduced with the integration of the ODGV. Since the VAWT is able to self-start at a lower wind speed, the working hour of the wind turbine would increase. At a wind speed of 6 m/s and under free-running condition (only rotor inertia and bearing friction were applied), the ODGV helps to increase the rotor rotational speed by 182%. With extra load application at the same wind speed (6 m/s), the wind turbine power output was increased by 3.48 times at its peak torque with the aid of the ODGV. The working concept of the ODGV is to minimize the negative torque zone of a lift-type VAWT and to reduce turbulence and rotational speed fluctuation. It was verified by re-simulating the torque coefficient data of a single bladed (NACA 0015 airfoil) VAWT published by the Sandia National Laboratories. From the simulation results, with the presence of the ODGV, it was shown that the

Extended parental care in communal social groups

Directory of Open Access Journals (Sweden)

Stephen H. Forbes

2002-11-01

Full Text Available Recent developments in social insect research have challenged the need for close kinship as a prerequisite for the evolution of stable group living. In a model communal bee species, Lasioglossum (Chilalictus hemichalceum, previous allozyme work indicated that groups of cooperating adult females are not relatives. Yet at any given time, not all group members perform the risky task of foraging. We previously hypothesized that tolerance for non-foragers was a component of extended parental care, previously known only for kin based social systems. DNA microsatellites were used to study colony genetic structure in order to test this hypothesis. Microsatellite polymorphism was substantial (He = 0.775. Overall intracolony relatedness, mainly of immatures, was low but significant in nine, late season nests (r = 0.136 plus or minus0.023, indicating that broods contain five to six unrelated sib ships. Detailed analyses of kinship between pairs of individuals revealed that most pairs were unrelated and most related pairs were siblings. Mothers are absent for 89-91% of the developing immature females, and 97% of developing males. Alternatively, 46% of adult females had neither sibs nor offspring in their nests. These findings indicate that the extended parental care model applies broadly to both kin based and nonkin based social systems in the Hymenoptera.

How Far Can Extended Knowledge Be Extended?

DEFF Research Database (Denmark)

Wray, K. Brad

2018-01-01

by an artifact, like a notebook or telescope. The chapter illustrates this by applying Pritchard’s account of extended knowledge to collaborating scientists. The beliefs acquired through collaborative research cannot satisfy both of Pritchard’s conditions of creditability. Further, there is evidence......Duncan Pritchard (2010) has developed a theory of extended knowledge based on the notion of extended cognition initially developed by Clark and Chalmers (1998). Pritchard’s account gives a central role to the notion of creditability, which requires the following two conditions to be met: (i...... that scientists are not prepared to take responsibility for the actions of the scientists with whom they collaborate....

A DOZEN NEW GALAXIES CAUGHT IN THE ACT: GAS STRIPPING AND EXTENDED EMISSION LINE REGIONS IN THE COMA CLUSTER

International Nuclear Information System (INIS)

Yagi, Masafumi; Komiyama, Yutaka; Kashikawa, Nobunari; Yoshida, Michitoshi; Furusawa, Hisanori; Okamura, Sadanori; Graham, Alister W.; Miller, Neal A.; Carter, David; Mobasher, Bahram; Jogee, Shardha

2010-01-01

We present images of extended Hα clouds associated with 14 member galaxies in the Coma cluster obtained from deep narrowband imaging observations with the Suprime-Cam at the Subaru Telescope. The parent galaxies of the extended Hα clouds are distributed farther than 0.2 Mpc from the peak of the X-ray emission of the cluster. Most of the galaxies are bluer than g - r ∼ 0.5 and they account for 57% of the blue (g - r < 0.5) bright (r < 17.8 mag) galaxies in the central region of the Coma cluster. They reside near the red- and blueshifted edges of the radial velocity distribution of Coma cluster member galaxies. Our findings suggest that most of the parent galaxies were recently captured by the Coma cluster potential and are now infalling toward the cluster center with their disk gas being stripped off and producing the observed Hα clouds.

Cavitation on a scaled-down model of a Francis turbine guide vane: high-speed imaging and PIV measurements

Science.gov (United States)

Pervunin, K. S.; Timoshevskiy, M. V.; Churkin, S. A.; Kravtsova, A. Yu; Markovich, D. M.; Hanjalić, K.

2015-12-01

Cavitation on two symmetric foils, a NACA0015 hydrofoil and a scaled-down model of a Francis turbine guide vane (GV), was investigated by high-speed visualization and PIV. At small attack angles the differences between the profiles of the mean and fluctuating velocities for both hydrofoils were shown to be insignificant. However, at the higher angle of incidence, flow separation from the GV surface was discovered for quasi-steady regimes including cavitation-free and cavitation inception cases. The flow separation leads to the appearance of a second maximum in velocity fluctuations distributions downstream far from the GV surface. When the transition to unsteady regimes occurred, the velocity distributions became quite similar for both foils. Additionally, for the GV an unsteady regime characterized by asymmetric spanwise variations of the sheet cavity length along with alternating periodic detachments of clouds between the sidewalls of the test channel was for the first time visualized. This asymmetric behaviour is very likely to be governed by the cross instability that was recently described by Decaix and Goncalvès [8]. Moreover, it was concluded that the existence of the cross instability is independent on the test body shape and its aspect ratio.

Theoretical study of a novel refrigeration compressor - Part II: Performance of a rotating discharge valve in the revolving vane (RV) compressor

Energy Technology Data Exchange (ETDEWEB)

Teh, Y.L.; Ooi, K.T. [Thermal and Fluids Engineering Division, School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, S639798 (Singapore); Djamari, D. Wibowo [Engineering Mechanics Division, School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, S639798 (Singapore)

2009-08-15

A new refrigeration compressor, named 'Revolving Vane (RV) compressor', has been introduced in Part I of this paper series. For a first time in refrigeration compressors, a rotating discharge valve is employed in the RV compressor mainly due to the rotation of the entire cylinder. This paper presents a theoretical investigation on the dynamic behavior of a reed-type discharge valve undergoing rotatory motion, with the primary objective of elucidating the applicability of such valves in refrigeration compressors. Under the application of the Euler-Bernoulli beam theory, a mathematical model of the rotating valve is formulated and the transient response of the valve under centrifugal loads in addition to pressure forces is analyzed. Results have shown that under careful design considerations, the performance as well as the reliability of the rotating discharge valve can be enhanced as compared to a non-rotating valve that has been used in all refrigeration compressors currently. (author)

The Members of the Agency

International Nuclear Information System (INIS)

2003-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.58) is Kyrgyzstan, which deposited the instrument of acceptance of the Statute on 10 September 2003. The list shows the dates on which the present 137 Member States became Members

Thermal effects in concrete members

International Nuclear Information System (INIS)

Kar, A.K.

1977-01-01

When subjected to temperature changes and restrained from free movement, a member develops stresses. Restrained members are sometimes assumed to act independently of other members. A method of analysis and design for thermal stresses in such members is provided. The method of analysis, based on the ultimate strength concept, greatly reduces the computational efforts for determining thermal effects in concrete members. Available charts and tables and the recommendations given herein simplify the design. (Auth.)

The Members of the Agency

International Nuclear Information System (INIS)

2009-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.67) is Cambodia which deposited its Instrument of Acceptance of the Statute on 23 November 2009. The Attachment hereto shows the dates on which the present 151 Member States became Members [fr

The Members of the Agency

International Nuclear Information System (INIS)

2007-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.63) is Palau which deposited its Instrument of Acceptance of the Statute on 2 March 2007. The Attachment hereto shows the dates on which the present 144 Member States became Members

The Members of the Agency

International Nuclear Information System (INIS)

2009-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.67) is Cambodia which deposited its Instrument of Acceptance of the Statute on 23 November 2009. The Attachment hereto shows the dates on which the present 151 Member States became Members

The Members of the Agency

International Nuclear Information System (INIS)

2008-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.64) is Nepal which deposited its Instrument of Acceptance of the Statute on 8 July 2008. The Attachment hereto shows the dates on which the present 145 Member States became Members

The Members of the Agency

International Nuclear Information System (INIS)

2006-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.62) is Montenegro which deposited its Instrument of Acceptance of the Statute on 30 October 2006. The Attachment hereto shows the dates on which the present 143 Member States became Members

The Members of the Agency

International Nuclear Information System (INIS)

2009-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.67) is Cambodia which deposited its Instrument of Acceptance of the Statute on 23 November 2009. The Attachment hereto shows the dates on which the present 151 Member States became Members [ru

The Members of the Agency

International Nuclear Information System (INIS)

2009-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.67) is Cambodia which deposited its Instrument of Acceptance of the Statute on 23 November 2009. The Attachment hereto shows the dates on which the present 151 Member States became Members [es

The Members of the Agency

International Nuclear Information System (INIS)

2006-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.60) is Chad, which deposited the instrument of acceptance of the Statute on 2 November 2005. The Attachment hereto shows the dates on which the present 139 Member States became Members

The Members of the Agency

International Nuclear Information System (INIS)

2009-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.65) is the Sultanate of Oman which deposited its Instrument of Acceptance of the Statute on 5 February 2009. The Attachment hereto shows the dates on which the present 146 Member States became Members

The Members of the Agency

International Nuclear Information System (INIS)

2009-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.65) is the Sultanate of Oman which deposited its Instrument of Acceptance of the Statute on 5 February 2009. The Attachment hereto shows the dates on which the present 146 Member States became Members [fr

The Members of the Agency

International Nuclear Information System (INIS)

2005-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.59) is the Islamic Republic of Mauritania, which deposited the instrument of acceptance of the Statute on 23 November 2004. The Attachment hereto shows the dates on which the present 138 Member States became Members

The Members of the Agency

International Nuclear Information System (INIS)

2009-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.65) is the Sultanate of Oman which deposited its Instrument of Acceptance of the Statute on 5 February 2009. The Attachment hereto shows the dates on which the present 146 Member States became Members [es

The Text of the Second Agreement to Extend the Regional Co-operative Agreement for Research, Development and Training related to Nuclear Science and Technology of 1972

International Nuclear Information System (INIS)

1982-12-01

The text of the Second Agreement to Extend the Regional Co-operative Agreement for Research, Development and Training Related to Nuclear Science and Technology of 1972 the RCA Agreement, fist extended in 1977, for a further period of five years with effect from 12 June 1982, is reproduced herein for the information of all Members

Strategies to improve sleep during extended search and rescue operations.

Science.gov (United States)

Jenkins, Jennifer Lee; Fredericksen, Kim; Stone, Roger; Tang, Nelson

2007-01-01

This study investigated strategies to improve sleeping conditions during search and rescue operations during disaster response. Forty members of the Montgomery County (Maryland) Urban Search and Rescue Team were surveyed for individual sleep habits and sleeping aids used during extended deployments. Team members were also asked to suggest methods to improve sleep on future deployments. The average amount of sleep during field operations was 5.4 hours with a range of 4-8 hours. Eight percent surveyed would prefer another schedule besides the 12-hour work day, all of whom proposed three 8-hour shifts. Fifteen percent of participants were interested in a pharmacological sleeping aid. Fifty percent of search and rescue members interviewed would consider using nonpharmacological sleeping aids. Furthermore, 40% of participants stated they had successfully devised self-employed methods of sleep aids for previous deployments, such as ear plugs, massage, mental imagery, personal routines, music and headphones, reading, and blindfolds. This study suggests that availability of both pharmacological and nonpharmacological sleeping aids to search and rescue workers via the team cache could impact the quantity of sleep. Further investigation into methods of optimizing sleep during field missions could theoretically show enhanced performance through various aspects of missions including mitigation of errors, improved productivity, and improved overall physiological and emotional well-being of search and rescue personnel.

Extended objects

International Nuclear Information System (INIS)

Creutz, M.

1976-01-01

After some disconnected comments on the MIT bag and string models for extended hadrons, I review current understanding of extended objects in classical conventional relativistic field theories and their quantum mechanical interpretation

The Members of the Agency

International Nuclear Information System (INIS)

2006-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.61) are Belize, Mozambique and Malawi, which deposited their Instruments of Acceptance of the Statute on 31 March 2006, 18 September 2006 and 2 October 2006 respectively. The Attachment hereto shows the dates on which the present 142 Member States became Members [fr

The Members of the Agency

International Nuclear Information System (INIS)

2006-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.61) are Belize, Mozambique and Malawi, which deposited their Instruments of Acceptance of the Statute on 31 March 2006, 18 September 2006 and 2 October 2006 respectively. The Attachment hereto shows the dates on which the present 142 Member States became Members

The Members of the Agency

International Nuclear Information System (INIS)

2009-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.66) are Bahrain, Burundi, Congo and Lesotho which deposited their Instruments of Acceptance of the Statute on 23 June 2009, 24 June 2009, 15 July 2009 and 13 July 2009, respectively. The Attachment hereto shows the dates on which the present 150 Member States became Members [fr

The Members of the Agency

International Nuclear Information System (INIS)

2009-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.66) are Bahrain, Burundi, Congo and Lesotho which deposited their Instruments of Acceptance of the Statute on 23 June 2009, 24 June 2009, 15 July 2009 and 13 July 2009, respectively. The Attachment hereto shows the dates on which the present 150 Member States became Members

The Members of the Agency

International Nuclear Information System (INIS)

2009-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.66) are Bahrain, Burundi, Congo and Lesotho which deposited their Instruments of Acceptance of the Statute on 23 June 2009, 24 June 2009, 15 July 2009 and 13 July 2009, respectively. The Attachment hereto shows the dates on which the present 150 Member States became Members [ru

The Members of the Agency

International Nuclear Information System (INIS)

2009-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.66) are Bahrain, Burundi, Congo and Lesotho which deposited their Instruments of Acceptance of the Statute on 23 June 2009, 24 June 2009, 15 July 2009 and 13 July 2009, respectively. The Attachment hereto shows the dates on which the present 150 Member States became Members [es

7 CFR 983.42 - Initial members and nomination of successor members.

Science.gov (United States)

2010-01-01

...) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF... alternate is selected shall serve in place of that member on the committee, and shall have and be able to... members of the committee shall serve for terms of two years: Provided, That four of the initially selected...

Chemical Abundances of New Member Stars in the Tucana II Dwarf Galaxy

Science.gov (United States)

Chiti, Anirudh; Frebel, Anna; Ji, Alexander P.; Jerjen, Helmut; Kim, Dongwon; Norris, John E.

2018-04-01

We present chemical abundance measurements for seven stars with metallicities ranging from Fe/H] = ‑3.3 to [Fe/H] = ‑2.4 in the Tucana II ultra-faint dwarf galaxy (UFD), based on high-resolution spectra obtained with the MIKE spectrograph on the 6.5 m Magellan-Clay Telescope. For three stars, we present detailed chemical abundances for the first time. Of those, two stars are newly discovered members of Tucana II and were selected as probable members from deep narrowband photometry of the Tucana II UFD taken with the SkyMapper telescope. This result demonstrates the potential for photometrically identifying members of dwarf galaxy systems based on chemical composition. One new star was selected from the membership catalog of Walker et al. The other four stars in our sample have been reanalyzed, following additional observations. Overall, six stars have chemical abundances that are characteristic of the UFD stellar population. The seventh star shows chemical abundances that are discrepant from the other Tucana II members and an atypical, higher strontium abundance than what is expected for typical UFD stars. While unlikely, its strontium abundance raises the possibility that it may be a foreground metal-poor halo star with the same systemic velocity as Tucana II. If we were to exclude this star, Tucana II would satisfy the criteria to be a surviving first galaxy. Otherwise, this star implies that Tucana II has likely experienced somewhat extended chemical evolution. This paper includes data gathered with the 6.5 m Magellan Telescopes located at Las Campanas Observatory, Chile.

THE EXTENDED VIRGO CLUSTER CATALOG

Energy Technology Data Exchange (ETDEWEB)

Kim, Suk; Rey, Soo-Chang; Lee, Youngdae; Chung, Jiwon; Pak, Mina; Yi, Wonhyeong; Lee, Woong [Department of Astronomy and Space Science, Chungnam National University, 99 Daehak-ro, Daejeon 305-764 (Korea, Republic of); Jerjen, Helmut [Research School of Astronomy and Astrophysics, The Australian National University, Cotter Road, Weston, ACT 2611 (Australia); Lisker, Thorsten [Astronomisches Rechen-Institut, Zentrum für Astronomie der Universität Heidelberg (ZAH), Mönchhofstraße 12-14, D-69120 Heidelberg (Germany); Sung, Eon-Chang [Korea Astronomy and Space Science institute, 776 Daedeokdae-ro, Daejeon 305-348 (Korea, Republic of)

2015-01-01

We present a new catalog of galaxies in the wider region of the Virgo cluster, based on the Sloan Digital Sky Survey (SDSS) Data Release 7. The Extended Virgo Cluster Catalog (EVCC) covers an area of 725 deg{sup 2} or 60.1 Mpc{sup 2}. It is 5.2 times larger than the footprint of the classical Virgo Cluster Catalog (VCC) and reaches out to 3.5 times the virial radius of the Virgo cluster. We selected 1324 spectroscopically targeted galaxies with radial velocities less than 3000 km s{sup –1}. In addition, 265 galaxies that have been overlooked in the SDSS spectroscopic survey but have available redshifts in the NASA Extragalactic Database are also included. Our selection process secured a total of 1589 galaxies, 676 of which are not included in the VCC. The certain and possible cluster members are defined by means of redshift comparison with a cluster infall model. We employed two independent and complementary galaxy classification schemes: the traditional morphological classification based on the visual inspection of optical images and a characterization of galaxies from their spectroscopic features. SDSS u, g, r, i, and z passband photometry of all EVCC galaxies was performed using Source Extractor. We compare the EVCC galaxies with the VCC in terms of morphology, spatial distribution, and luminosity function. The EVCC defines a comprehensive galaxy sample covering a wider range in galaxy density that is significantly different from the inner region of the Virgo cluster. It will be the foundation for forthcoming galaxy evolution studies in the extended Virgo cluster region, complementing ongoing and planned Virgo cluster surveys at various wavelengths.

Improvement of the efficiency of the Agnew micro hydro turbine at part loads due to installing guide vanes mechanism

Energy Technology Data Exchange (ETDEWEB)

Yassi, Yousef; hashemloo, Safar [Iranian Research Organization for Science and Technology (IROST), No. 29 Forssat St., Enghelaab Ave., Tehran (Iran)

2010-10-15

Agnew turbine is an axial micro hydro of Kaplan type, with its main shaft subtending 45 to the line of horizon. Due to governmental power generating programs for limited hydro potentials in Iran and on the basis of a joint project between the University of Glasgow and the Iranian Research Organization for Science and Technology (IROST), the turbine was developed to operate under low heads and limited flow potentials in Iran. However the turbine was originally designed to operate without any guide vanes and test results showed that the turbine achieved an efficiency of 62% at its best point of performance. Later a modified Agnew turbine, consisting of a guide blades mechanism was designed and manufactured, at (IROST). The mechanism was so designed that it was also used as a second support for the turbine's main shaft. The standard turbine tests proved that; the modified version of the Agnew turbine had 23% higher efficiency at its best performance point; compared to the original design. Then the effects of the improvements on the turbine were studied on the performance of the turbine at part loads. However, efficiency improvements were observed under all part load conditions. (author)

Improvement of the efficiency of the Agnew micro hydro turbine at part loads due to installing guide vanes mechanism

International Nuclear Information System (INIS)

Yassi, Yousef; Hashemloo, Safar

2010-01-01

Agnew turbine is an axial micro hydro of Kaplan type, with its main shaft subtending 45 deg. to the line of horizon. Due to governmental power generating programs for limited hydro potentials in Iran and on the basis of a joint project between the University of Glasgow and the Iranian Research Organization for Science and Technology (IROST), the turbine was developed to operate under low heads and limited flow potentials in Iran. However the turbine was originally designed to operate without any guide vanes and test results showed that the turbine achieved an efficiency of 62% at its best point of performance. Later a modified Agnew turbine, consisting of a guide blades mechanism was designed and manufactured, at (IROST). The mechanism was so designed that it was also used as a second support for the turbine's main shaft. The standard turbine tests proved that; the modified version of the Agnew turbine had 23% higher efficiency at its best performance point; compared to the original design. Then the effects of the improvements on the turbine were studied on the performance of the turbine at part loads. However, efficiency improvements were observed under all part load conditions.

Extended radio sources in the cluster environment

International Nuclear Information System (INIS)

Burns, J.O. Jr.

1979-01-01

Extended radio galaxies that lie in rich and poor clusters were studied. A sample of 3CR and 4C radio sources that spatially coincide with poor Zwicky clusters of galaxies was observed to obtain accurate positions and flux densities. Then interferometer observations at a resolution of approx. = 10 arcsec were performed on the sample. The resulting maps were used to determine the nature of the extended source structure, to make secure optical identifications, and to eliminate possible background sources. The results suggest that the environments around both classical double and head-tail radio sources are similar in rich and poor clusters. The majority of the poor cluster sources exhibit some signs of morphological distortion (i.e., head-tails) indicative of dynamic interaction with a relatively dense intracluster medium. A large fraction (60 to 100%) of all radio sources appear to be members of clusters of galaxies if one includes both poor and rich cluster sources. Detailed total intensity and polarization observations for a more restricted sample of two classical double sources and nine head-tail galaxies were also performed. The purpose was to examine the spatial distributions of spectral index and polarization. Thin streams of radio emission appear to connect the nuclear radio-point components to the more extended structures in the head-tail galaxies. It is suggested that a non-relativistic plasma beam can explain both the appearance of the thin streams and larger-scale structure as well as the energy needed to generate the observed radio emission. The rich and poor radio cluster samples are combined to investigate the relationship between source morphology and the scale sizes of clustering. There is some indication that a large fraction of radio sources, including those in these samples, are in superclusters of galaxies

VizieR Online Data Catalog: NGC 6802 dwarf cluster members and non-members (Tang+, 2017)

Science.gov (United States)

Tang, B.; Geisler, D.; Friel, E.; Villanova, S.; Smiljanic, R.; Casey, A. R.; Randich, S.; Magrini, L.; San, Roman I.; Munoz, C.; Cohen, R. E.; Mauro, F.; Bragaglia, A.; Donati, P.; Tautvaisiene, G.; Drazdauskas, A.; Zenoviene, R.; Snaith, O.; Sousa, S.; Adibekyan, V.; Costado, M. T.; Blanco-Cuaresma, S.; Jimenez-Esteban, F.; Carraro, G.; Zwitter, T.; Francois, P.; Jofre, P.; Sordo, R.; Gilmore, G.; Flaccomio, E.; Koposov, S.; Korn, A. J.; Lanzafame, A. C.; Pancino, E.; Bayo, A.; Damiani, F.; Franciosini, E.; Hourihane, A.; Lardo, C.; Lewis, J.; Monaco, L.; Morbidelli, L.; Prisinzano, L.; Sacco, G.; Worley, C. C.; Zaggia, S.

2016-11-01

The dwarf stars in NGC 6802 observed by GIRAFFE spectrograph are separated into four tables: 1. cluster members in the lower main sequence; 2. cluster members in the upper main sequence; 3. non-member dwarfs in the lower main sequence; 4. non-member dwarfs in the upper main sequence. The star coordinates, V band magnitude, V-I color, and radial velocity are given. (4 data files).

Decision-Making of Patients With Implantable Cardioverter-Defibrillators at End of Life: Family Members' Experiences.

Science.gov (United States)

Lee, Mei Ching; Sulmasy, Daniel P; Gallo, Joseph; Kub, Joan; Hughes, Mark T; Russell, Stuart; Kellogg, Anela; Owens, Sharon G; Terry, Peter; Nolan, Marie T

2017-07-01

Many patients with advanced heart failure (HF) experience the life-extending benefits of implantable cardioverter-defibrillators (ICD), but at the end stage of HF, patients may experience shocks with increasing frequency and change the plan for end-of-life (EOL) care including the deactivation of the ICD. This report describes family members' experiences of patients with ICD making decisions at EOL. Understanding the decision-making of patients with ICD at EOL can promote informed decision-making and improve the quality of EOL care. This pilot study used a mixed methods approach to test the effects of a nurse-guided discussion in decision-making about ICD deactivation (turning off the defibrillation function) at the EOL. Interviews were conducted, audiotaped, and transcribed in 2012 to 2013 with 6 family members of patients with advanced HF and ICDs. Three researchers coded the data and identified themes in 2014. Three main themes described family members' experiences related to patients having HF with ICDs making health-care decision at EOL: decision-making preferences, patients' perception on ICD deactivation, and communication methods. Health-care providers need to have knowledge of patients' decision-making preferences. Preferences for decision-making include the allowing of appropriate people to involve and encourages direct conversation with family members even when advance directives is completed. Information of ICD function and the option of deactivation need to be clearly delivered to patients and family members. Education and guidelines will facilitate the communication of the preferences of EOL care.

26 CFR 1.121-5 - Suspension of 5-year period for certain members of the uniformed services and Foreign Service.

Science.gov (United States)

2010-04-01

... REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED... official extended duty as a member of the Foreign Service of the United States in Brazil. In 2015 B sells... period of ownership and use during his 8-year period of service with the Foreign Service in Brazil. If B...

The Text of the Third Agreement to Extend the Regional Co-operative Agreement for Research, Development and Training related to Nuclear Science and Technology of 1972

International Nuclear Information System (INIS)

1987-09-01

The text of the Third Agreement to Extend the Regional Co-operative Agreement for Research, Development and Training Related to Nuclear Science and Technology of 1972 the RCA Agreement, extended first in 1977 and then in 1982, for a further period of five years with effect from 12 June 1987, is reproduced herein for the information of all Members [fr

3rd Annual Disruptive Technology Conference

Science.gov (United States)

2006-09-07

Panel -- The Warfighter’s Perspective The Impact of Disruptive Technologies on Joint Warfighting MG Michael Vane, USA, Vice Director for Force...Structure, Resources & Assessment, Joint Staff, J-8 Panel -- Perspectives of Change: Identifying the Emerging Commercial Disruptive Technologies Decision...Mark Lucas, Board Member OSGeo, RadiantBlue Technologies Panel -- The Search for Disruptive Technologies - a “Blue Force” Multiplier Advanced

Perspectives on extended Deterrence

International Nuclear Information System (INIS)

Tertrais, Bruno; Yost, David S.; Bunn, Elaine; Lee, Seok-soo; Levite, Ariel e.; Russell, James A.; Hokayem, Emile; Kibaroglu, Mustafa; Schulte, Paul; Thraenert, Oliver; Kulesa, Lukasz

2010-05-01

In November 2009, the Foundation for Strategic Research (Fondation pour la recherche strategique, FRS) convened a workshop on 'The Future of extended Deterrence', which included the participation of some of the best experts of this topic, from the United States, Europe, the Middle East and East Asia, as well as French and NATO officials. This document brings together the papers prepared for this seminar. Several of them were updated after the publication in April 2010 of the US Nuclear Posture Review. The seminar was organized with the support of the French Atomic energy Commission (Commissariat a l'energie atomique - CEA). Content: 1 - The future of extended deterrence: a brainstorming paper (Bruno Tertrais); 2 - US extended deterrence in NATO and North-East Asia (David S. Yost); 3 - The future of US extended deterrence (Elaine Bunn); 4 - The future of extended deterrence: a South Korean perspective (Seok-soo Lee); 5 - Reflections on extended deterrence in the Middle East (Ariel e. Levite); 6 - extended deterrence, security guarantees and nuclear weapons: US strategic and policy conundrums in the Gulf (James A. Russell); 7 - extended deterrence in the Gulf: a bridge too far? (Emile Hokayem); 8 - The future of extended deterrence: the case of Turkey (Mustafa Kibaroglu); 9 - The future of extended deterrence: a UK view (Paul Schulte); 10 - NATO and extended deterrence (Oliver Thraenert); 11 - extended deterrence and assurance in Central Europe (Lukasz Kulesa)

The Members of the Agency

International Nuclear Information System (INIS)

1999-01-01

The document lists the 130 Member States of the Agency as of 1 December 1999. The new Member since the last issue of the list (INFCIRC/2/52) is Angola. The dates on which the present 130 Member States became Members, and the state Honduras) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute are given in an Attachment

Simulation of performance of centrifugal circulators with vane-less diffuser for GCR applications - HTR2008-58166

International Nuclear Information System (INIS)

Tauveron, N.

2008-01-01

In the frame of the international forum Gen lV, CEA has selected various innovative concepts of Gas cooled Nuclear Reactor. Among them, an indirect-cycle gas reactor is under consideration. Thermal hydraulic performances are a key issue for the design. For transient conditions and decay heat removal situations, the thermal hydraulic performance must remain as high as possible. In this context, all the transient situations, the incidental and accidental scenarios must be evaluated by a validated sys-tem code able to correctly describe, in particular, the thermal-hydraulics of the whole plant. As concepts use a helium compressor to maintain the flow in the core, a special emphasis must be laid on compressor modelling. Centrifugal circulators with a vane-less diffuser have significant properties in term of simplicity, cost, ability to operate over a wide range of conditions. The objective of this paper is to present a dedicated description of centrifugal compressor, based on a one dimensional approach. This type of model requires various correlations as input data. The present contribution consists in establishing and validating the numerical simulations (including different sets of correlations) by comparison with representative experimental data. The results obtained show a qualitatively correct behaviour of the model compared to open literature cases of the gas turbine aircraft community and helium circulators of High Temperature Gas Reactors. Further work on modelling and validation are nevertheless needed to have a better confidence in the simulation predictions. (authors)

Extended Emotions

DEFF Research Database (Denmark)

Krueger, Joel; Szanto, Thomas

2016-01-01

beyond the neurophysiological confines of organisms; some even argue that emotions can be socially extended and shared by multiple agents. Call this the extended emotions thesis (ExE). In this article, we consider different ways of understanding ExE in philosophy, psychology, and the cognitive sciences...

Family members' experiences of autopsy

NARCIS (Netherlands)

Oppewal, F; Meyboom-de Jong, B

Background. The experiences of family members will teach us how to handle an autopsy, the ultimate quality assessment tool. Objective. The aim of this study was to determine surviving family members' experience of autopsy. Method. Seven GPs were asked to approach surviving family members of

Jervell and Lange-Nielsen syndrome in a father and daughter from a large highly inbred family: a 16-year follow-up of 59 living members.

Science.gov (United States)

Sanyal, Shyamal Kumar; Kaul, Kanwar K; Hussein, Akhtar; Wilroy, Robert S; Agarwal, Kisan; Sohel, Saira

2013-08-01

To report the autosomal dominant inheritance of the Jervell and Lange-Nielsen syndrome in a highly inbred family, the initiation of Torsades de Pointes, and the natural history of the syndrome based on a 16-year follow-up of the kindred. A family tree was constructed that included 66 blood relatives from three successive generations. Electrocardiograms were obtained from 59 living members including the proband, four members from a nuclear family, and 54 from the extended family. Evoked response audiometry was recorded for the proband and the nuclear family. All 59 family members were followed up regularly for 16 years. A total of 24 living members were affected--QTc: 480-680 ms. The proband had long QTc, bilateral high-tone sensorineural deafness, recurrent syncope, and Torsades de Pointes. The asymptomatic father had long QTc and unilateral high-tone sensorineural deafness that involved specifically the left ear. One asymptomatic sibling of the proband had long QTc and normal hearing. The mother and another sibling were asymptomatic; QTc and hearing were normal in both. A total of 21 affected members from the extended family had only long QTc, and all were asymptomatic. There were three congenitally deaf first cousins who had recurrent syncope and adrenergic-triggered sudden death. In all, seven of 10 parents had consanguineous marriage to a first cousin. Each affected offspring had at least one affected parent. The severely symptomatic proband who received only β-blocker therapy and the 23 affected members without antiadrenergic therapy, all remained asymptomatic throughout the 16-year follow-up period. Jervell and Lange-Nielsen syndrome was inherited as autosomal dominant in this kindred. The majority of the affected members had a mild phenotype. The severity of auditory and cardiac phenotypes corresponded.

The Members of the Agency

International Nuclear Information System (INIS)

2003-01-01

The document lists the 135 Member States of the Agency as of 19 March 2003. The new Member since the last issue of the list (INFCIRC/2/56) is the Republic of Honduras. The dates on which the present 135 Member States became Members are given in an Attachment. It also shows the States whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute

The Members of the Agency

International Nuclear Information System (INIS)

2002-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.55) is the Republic of Botswana, which deposited the instrument of acceptance of the Statute on 20 March 2002. The Attachment hereto shows the dates on which the present 134 Member States became Members. It also shows the State whose application for membership of the Agency has been approved by the General Conference, but which has not yet deposited an instrument of acceptance of the Statute

The Members of the Agency

International Nuclear Information System (INIS)

2001-01-01

The document lists the 132 Member States of the Agency as of 1 June 2001. The new Members since the last issue of the list (INFCIRC/2/53) are Central African Republic and Azerbaijan. The dates on which the present 132 Member States became Members are given in an Attachment. It also shows the States whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute

The members of the Agency

International Nuclear Information System (INIS)

1996-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.46) is Bosnia and Herzegovina. The Attachment hereto shows the dates on which the present 123 Member States became Members. It also shows the States whose applications for membership of the Agency have been approved by the General Conference but which have not yet deposited an instrument of acceptance of the Statute and the State whose application for membership has been recommended by the Board of Governors for approval by the General Conference

The Members of the Agency

International Nuclear Information System (INIS)

1995-01-01

No new Member has joined the Agency since the last list of Member States was issued (INFCIRC/2/Rev.45). The Attachment hereto shows the dates on which the present 122 Member States became Members. It also shows the State whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States whose applications for membership have been recommended by the Board of Governors for approval by the General Conference

The Members of the Agency

International Nuclear Information System (INIS)

2003-01-01

The document lists the 136 Member States of the Agency as of 6 May 2003. The new Members since the last issue of the list (INFCIRC/2/57) are Eritrea and the Republic of Seychelles. Cambodia withdrew from the Agency with effect from 26 March 2003. The dates on which the present 136 Member States became Members are given in an Attachment. It also shows the States whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute

The Members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-11

No new Member has joined the Agency since the last list of Member States was issued (INFCIRC/2/Rev.45). The Attachment hereto shows the dates on which the present 122 Member States became Members. It also shows the State whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States whose applications for membership have been recommended by the Board of Governors for approval by the General Conference.

The members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-26

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.46) is Bosnia and Herzegovina. The Attachment hereto shows the dates on which the present 123 Member States became Members. It also shows the States whose applications for membership of the Agency have been approved by the General Conference but which have not yet deposited an instrument of acceptance of the Statute and the State whose application for membership has been recommended by the Board of Governors for approval by the General Conference.

7 CFR 1425.19 - Member cooperatives.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Member cooperatives. 1425.19 Section 1425.19... OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS COOPERATIVE MARKETING ASSOCIATIONS § 1425.19 Member cooperatives. A CMA may obtain loans or LDP's on behalf of a member cooperative when the member...

The Members of the Agency

International Nuclear Information System (INIS)

2014-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.76) is Brunei Darussalam, which deposited its instrument of acceptance of the Statute on 18 February 2014. The Attachment hereto shows the dates on which the present 162 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.71) is Rwanda, which deposited its instrument of acceptance of the Statute on 4 September 2012. The Attachment hereto shows the dates on which the present 155 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.70) is Papua New Guinea, which deposited its instrument of acceptance of the Statute on 4 April 2012. The Attachment hereto shows the dates on which the present 154 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government

The Members of the Agency

International Nuclear Information System (INIS)

2013-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.74) is Swaziland, which deposited its instrument of acceptance of the Statute on 15 February 2013. The Attachment hereto shows the dates on which the present 159 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.71) is Rwanda, which deposited its instrument of acceptance of the Statute on 4 September 2012. The Attachment hereto shows the dates on which the present 155 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government

The Members of the Agency

International Nuclear Information System (INIS)

2014-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.76) is Brunei Darussalam, which deposited its instrument of acceptance of the Statute on 18 February 2014. The Attachment hereto shows the dates on which the present 162 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.73) is Trinidad and Tobago, which deposited its instrument of acceptance of the Statute on 9 November 2012. The Attachment hereto shows the dates on which the present 158 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.71) is Rwanda, which deposited its instrument of acceptance of the Statute on 4 September 2012. The Attachment hereto shows the dates on which the present 155 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es

The Members of the Agency

International Nuclear Information System (INIS)

2014-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.76) is Brunei Darussalam, which deposited its instrument of acceptance of the Statute on 18 February 2014. The Attachment hereto shows the dates on which the present 162 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.71) is Rwanda, which deposited its instrument of acceptance of the Statute on 4 September 2012. The Attachment hereto shows the dates on which the present 155 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [ru

The Members of the Agency

International Nuclear Information System (INIS)

2001-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.54) are the Republic of Tajikistan, which deposited the instrument of acceptance of the Statute on 10 September 2001 and the Federal Republic of Yugoslavia, which deposited the instrument of acceptance of the Statute on 31 October 2001. The Attachment hereto shows the dates on which the present 133 Member States became Members. It also shows the States whose applications for membership of the Agency have been approved by the General Conference, but which have not yet deposited an instrument of acceptance of the Statute

The members of the Agency

International Nuclear Information System (INIS)

1996-01-01

The document lists the 124 Member States of the Agency as of 1 September 1996. The new Member since the last issue of the list (INFCIRC/2/Rev.47) is Georgia. In an attachment are given the dates on which the 124 Member States became Members, the State (Latvia) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the State (Republic of Moldova) whose application for membership has been recommended by the Board of Governors for approval by the General Conference

The members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-10

The document lists the 124 Member States of the Agency as of 1 September 1996. The new Member since the last issue of the list (INFCIRC/2/Rev.47) is Georgia. In an attachment are given the dates on which the 124 Member States became Members, the State (Latvia) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the State (Republic of Moldova) whose application for membership has been recommended by the Board of Governors for approval by the General Conference.

The method of the gas-dynamic centrifugal compressor stage characteristics recalculation for variable rotor rotational speeds and the rotation angle of inlet guide vanes blades if the kinematic and dynamic similitude conditions are not met

Science.gov (United States)

Vanyashov, A. D.; Karabanova, V. V.

2017-08-01

A mathematical description of the method for obtaining gas-dynamic characteristics of a centrifugal compressor stage is proposed, taking into account the control action by varying the rotor speed and the angle of rotation of the guide vanes relative to the "basic" characteristic, if the kinematic and dynamic similitude conditions are not met. The formulas of the correction terms for the non-dimensional coefficients of specific work, consumption and efficiency are obtained. A comparative analysis of the calculated gas-dynamic characteristics of a high-pressure centrifugal stage with experimental data is performed.

Members of the LHC Resources Review Boards

CERN Multimedia

Maximilien Brice

2002-01-01

Photo 01: Members of the LHCRRB visiting Point 2, hosting the ALICE experiment From l. to r. : W. Korda, Head of the VIP Office; P. Rimmer, CERN public relations, J. Seed, Member of the LHCRRB, J.-P. Revol, ALICE CERN Team Leader; J. Bartke, Member of the LHCRRB; F. Suransky, Member of the LHCRRB; J. Schukraft, Spokesperson, ALICE experiment and S. Molinari, VIP Office. Photo 02: Members of the LHC Resources Review Boards visiting the ALICE magnet at Point 2. L. to. r.: O. Dines-Hansen, H. Boggild, S. Irgens-Jensens, H.A. Gustafsson Photo 03: Members of the LHCRRB visiting Point 2, hosting the ALICE experiment From l. t to r.: J.Richter, Member of the LHCRRB; H. Gutbrod, Deputy Spokesperson, ALICE experiment; G. Paic, ALICE experiment; D. Muller, Member of the LHCRRB; P. Brau-Munzinger, ALICE experiment; R. Santo, Member of the LHCRRB, A. Van Rijn, Member of the LHCRRB; J. Engelen, Member of the LHCRRB.

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.70) is Papua New Guinea, which deposited its instrument of acceptance of the Statute on 4 April 2012. The Attachment hereto shows the dates on which the present 154 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.69) is the Commonwealth of Dominica, which deposited its instrument of acceptance of the Statute on 17 February 2012. The Attachment hereto shows the dates on which the present 153 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr

The Members of the Agency

International Nuclear Information System (INIS)

2011-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.68) is the Lao People's Democratic Republic which deposited its instrument of acceptance of the Statute on 4 November 2011. The Attachment hereto shows the dates on which the present 152 Member States deposited instruments of ratification or acceptance of the Statue with the depositary Government [fr

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.73) is Trinidad and Tobago, which deposited its instrument of acceptance of the Statute on 9 November 2012. The Attachment hereto shows the dates on which the present 158 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.70) is Papua New Guinea, which deposited its instrument of acceptance of the Statute on 4 April 2012. The Attachment hereto shows the dates on which the present 154 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [ru

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.69) is the Commonwealth of Dominica, which deposited its instrument of acceptance of the Statute on 17 February 2012. The Attachment hereto shows the dates on which the present 153 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.69) is the Commonwealth of Dominica, which deposited its instrument of acceptance of the Statute on 17 February 2012. The Attachment hereto shows the dates on which the present 153 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es

The Members of the Agency

International Nuclear Information System (INIS)

2011-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.68) is the Lao People's Democratic Republic which deposited its instrument of acceptance of the Statute on 4 November 2011. The Attachment hereto shows the dates on which the present 152 Member States deposited instruments of ratification or acceptance of the Statue with the depositary Government

The Members of the Agency

International Nuclear Information System (INIS)

2011-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.68) is the Lao People's Democratic Republic which deposited its instrument of acceptance of the Statute on 4 November 2011. The Attachment hereto shows the dates on which the present 152 Member States deposited instruments of ratification or acceptance of the Statue with the depositary Government [es

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.73) is Trinidad and Tobago, which deposited its instrument of acceptance of the Statute on 9 November 2012. The Attachment hereto shows the dates on which the present 158 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.70) is Papua New Guinea, which deposited its instrument of acceptance of the Statute on 4 April 2012. The Attachment hereto shows the dates on which the present 154 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es

Neural network integration during the perception of in-group and out-group members.

Science.gov (United States)

Greven, Inez M; Ramsey, Richard

2017-11-01

Group biases guide social interactions by promoting in-group favouritism, but the neural mechanisms underpinning group biases remain unclear. While neuroscience research has shown that distributed brain circuits are associated with seeing in-group and out-group members as "us" and "them", it is less clear how these networks exchange signals. This fMRI study uses functional connectivity analyses to investigate the contribution of functional integration to group bias modulation of person perception. Participants were assigned to an arbitrary group and during scanning they observed bodies of in-group or out-group members that cued the recall of positive or negative social knowledge. The results showed that functional coupling between perceptual and cognitive neural networks is tuned to particular combinations of group membership and social knowledge valence. Specifically, coupling between body perception and theory-of-mind networks is biased towards seeing a person that had previously been paired with information consistent with group bias (positive for in-group and negative for out-group). This demonstrates how brain regions associated with visual analysis of others and belief reasoning exchange and integrate signals when evaluating in-group and out-group members. The results update models of person perception by showing how and when interplay occurs between perceptual and extended systems when developing a representation of another person. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.72) are Fiji and Togo, which deposited their instruments of acceptance of the Statute on 2 November 2012 and 1 November 2012, respectively. The Attachment hereto shows the dates on which the present 157 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.72) are Fiji and Togo, which deposited their instruments of acceptance of the Statute on 2 November 2012 and 1 November 2012, respectively. The Attachment hereto shows the dates on which the present 157 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [ru

The Members of the Agency

International Nuclear Information System (INIS)

2014-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.75) are San Marino and the Bahamas, which deposited their instruments of acceptance of the Statute on 25 November 2013 and 7 January 2014, respectively. The Attachment hereto shows the dates on which the present 161 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.72) are Fiji and Togo, which deposited their instruments of acceptance of the Statute on 2 November 2012 and 1 November 2012, respectively. The Attachment hereto shows the dates on which the present 157 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government

The members of the Agency

International Nuclear Information System (INIS)

1993-01-01

The 42nd revision of INFCIRC/2 lists the 113 Member States of the International Atomic Energy Agency as of 1 January 1993. It includes Slovenia as a new Member State as of 21 September 1992, Cambodia replaces the former name ''Democratic Kampuchea'' and Czechoslovakia was deleted as it ceased to be a member of the Agency as of 1 January 1993 (INFCIRC/417)

The Members of the Agency

International Nuclear Information System (INIS)

2012-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.72) are Fiji and Togo, which deposited their instruments of acceptance of the Statute on 2 November 2012 and 1 November 2012, respectively. The Attachment hereto shows the dates on which the present 157 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es

The Members of the Agency

International Nuclear Information System (INIS)

2014-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.75) are San Marino and the Bahamas, which deposited their instruments of acceptance of the Statute on 25 November 2013 and 7 January 2014, respectively. The Attachment hereto shows the dates on which the present 161 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [es

The Members of the Agency

International Nuclear Information System (INIS)

2014-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.75) are San Marino and the Bahamas, which deposited their instruments of acceptance of the Statute on 25 November 2013 and 7 January 2014, respectively. The Attachment hereto shows the dates on which the present 161 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government [fr

Numerical study on dissimilar guide vane design with SCC piston for air and emulsified biofuel mixing improvement

Directory of Open Access Journals (Sweden)

Hamid Mohd Fadzli

2017-01-01

Full Text Available Crude palm oil (CPO is one of the most potential biofuels that can be applied in the conventional diesel engines, where the chemical properties of CPO are comparable to diesel fuel. However, its higher viscosity and heavier molecules can contributes to several engine problems such as low atomization during injection, carbon deposit formation, injector clogging, low mixing with air and lower combustion efficiency. An emulsification of biofuel and modifications of few engine critical components have been identified to mitigate the issues. This paper presents the effects of dissimilar guide vane design (GVD in terms of height variation of 0.25R, 0.3R and 0.35R at the intake manifold with shallow depth re-entrance combustion chamber (SCC piston application to the incylinder air flow characteristics improvement. The simulation results show that the intake manifold with GVD improved the performance of the air flow characteristic particularly swirl, tumble and cross tumble ratios from the intake manifold to the engine. The GVD with the height of 0.3R was found to be the optimum design with respect to the overall improvement of the air flow characteristic. The improvement of the air flow characteristic with the application of GVD and SCC piston in the engine was expected to contribute to a better air fuel mixing, fuel atomization and combustion efficiency of the engine using emulsified biofuel as a source of fuel.

The Members of the Agency

International Nuclear Information System (INIS)

1995-01-01

The new member since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.44) is Yemen. The Attachment hereto shows the dates on which the 122 States became members of the Agency, as well as the State whose application for membership of the Agency was approved by the General Conference, but which has not yet deposited an instrument of acceptance of the Statute

The Members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-02-13

The new member since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.44) is Yemen. The Attachment hereto shows the dates on which the 122 States became members of the Agency, as well as the State whose application for membership of the Agency was approved by the General Conference, but which has not yet deposited an instrument of acceptance of the Statute.

Extended icosahedral structures

CERN Document Server

Jaric, Marko V

1989-01-01

Extended Icosahedral Structures discusses the concepts about crystal structures with extended icosahedral symmetry. This book is organized into six chapters that focus on actual modeling of extended icosahedral crystal structures. This text first presents a tiling approach to the modeling of icosahedral quasiperiodic crystals. It then describes the models for icosahedral alloys based on random connections between icosahedral units, with particular emphasis on diffraction properties. Other chapters examine the glassy structures with only icosahedral orientational order and the extent of tra

Practitioner perspectives on extended clinical placement programs in optometry.

Science.gov (United States)

Bentley, Sharon A; Cartledge, Amy; Guest, Daryl J; Cappuccio, Skye; Woods, Craig A

2016-05-01

Some universities are looking to provide a more diverse range of clinical learning experiences through extended clinical placement programs. This approach will potentially have a significant impact on practitioners. The aim of this study was to conduct a national survey of optometrists to ascertain their perspectives on participating in extended clinical placement programs. Members of Optometry Australia were invited to participate in a survey conducted during June and July 2014. A total of 268 practitioners participated (six per cent of registered Australian optometrists): 159 were predominantly employees or locums and 109 were owners or managers who identified as the key representative of a practice or organisation for the purpose of this survey. Almost two-thirds (65 per cent) of participants, who were employees or locums were supportive of extended clinical placement programs. Among this group, females were more likely to be supportive than males (p = 0.033). In comparison, just over one-third (34 per cent) of participants who were key decision-makers were supportive, with 30 per cent possibly supportive and 36 per cent not supportive. Among key decision-makers, males were more likely to be supportive (p = 0.009). The top three perceived advantages of supervising a student were: opportunity to mentor early career development, opportunity to give back to the profession and future recruitment. The top three perceived disadvantages were: burden on time, decrease in number of patients examined and burden on support staff. Suggested incentives for supervising students were credit for continuing professional development and financial remuneration. There appears to be moderate support for extended clinical placement programs; however, there are incentives that might engage a larger proportion of the profession in the future. These findings can inform the development of effective and sustainable clinical training programs for optometry students. Additionally

The process of death imminence awareness by family members of patients in adult critical care.

Science.gov (United States)

Baumhover, Nancy C

2015-01-01

A focus on cost-effective quality end-of-life care remains a high priority in adult critical care given an aging population, high prevalence of death, and aggressive technologies used to extend or sustain life in this setting. A Glaserian grounded theory design was used to conduct this retrospective study to yield a substantive middle-range theory. The data source was semistructured interviews with 14 family members of decedents who died 6 to 60 months prior to the study. The purpose of this study was to generate a theory on how family members of patients in adult critical care come to realize that their loved one is dying. The Process of Death Imminence Awareness by Family Members of Patients in Adult Critical Care middle-range theory contained 6 phases: (1) patient's near-death awareness, (2) dying right in front of me, (3) turning points in the patient's condition, (4) no longer the person I once knew, (5) doing right by them, and (6) time to let go. Patient's near-death awareness preceded all other phases, if communicated by the decedent with their family. Then, family members iteratively moved through all the other key phases in the process until a time to let go became evident. This substantive middle-range theory will guide nursing education, practice, and research aimed at providing quality and cost-effective end-of-life care in adult critical care.

Understanding Heterogeneous Preferences of Cooperative Members

NARCIS (Netherlands)

Kalogeras, N.; Pennings, J.M.E.; Lans, van der I.A.; Garcia, P.; Dijk, van G.

2009-01-01

We study the heterogeneity in the preference structure of cooperative members. Using conjoint analysis the utility that members attach to intra-organizational and strategic attributes of their cooperative is elicited. Recognizing that members are not homogenous, a concomitant finitemixture

Reconstruction of the core and extended regulons of global transcription factors.

Directory of Open Access Journals (Sweden)

Yann S Dufour

2010-07-01

Full Text Available The processes underlying the evolution of regulatory networks are unclear. To address this question, we used a comparative genomics approach that takes advantage of the large number of sequenced bacterial genomes to predict conserved and variable members of transcriptional regulatory networks across phylogenetically related organisms. Specifically, we developed a computational method to predict the conserved regulons of transcription factors across alpha-proteobacteria. We focused on the CRP/FNR super-family of transcription factors because it contains several well-characterized members, such as FNR, FixK, and DNR. While FNR, FixK, and DNR are each proposed to regulate different aspects of anaerobic metabolism, they are predicted to recognize very similar DNA target sequences, and they occur in various combinations among individual alpha-proteobacterial species. In this study, the composition of the respective FNR, FixK, or DNR conserved regulons across 87 alpha-proteobacterial species was predicted by comparing the phylogenetic profiles of the regulators with the profiles of putative target genes. The utility of our predictions was evaluated by experimentally characterizing the FnrL regulon (a FNR-type regulator in the alpha-proteobacterium Rhodobacter sphaeroides. Our results show that this approach correctly predicted many regulon members, provided new insights into the biological functions of the respective regulons for these regulators, and suggested models for the evolution of the corresponding transcriptional networks. Our findings also predict that, at least for the FNR-type regulators, there is a core set of target genes conserved across many species. In addition, the members of the so-called extended regulons for the FNR-type regulators vary even among closely related species, possibly reflecting species-specific adaptation to environmental and other factors. The comparative genomics approach we developed is readily applicable to other

The IAEA Member States' database of discharges of radionuclides to the atmosphere and the aquatic environment (DIRATA)

International Nuclear Information System (INIS)

Berkovskyy, Volodymyr; Hood, Graeme

2008-01-01

Full text: This paper provides the abstract model for authors. It embodies all the required formats and it is written complying with them. DIRATA is the IAEA Member States' database on discharges of radionuclides to the atmosphere and the aquatic environment (http://dirata.iaea.org/). It is a worldwide centralized repository of data submitted by IAEA Member States on a voluntary basis and each site dataset includes annual discharge and detection limits. Regulatory limits are given by Member States whenever available and a limited amount of information on the location of the site (country, geographical coordinates, water body into which radioactivity is released, number, names and types of installations) is also included. One of important purposes of DIRATA is to assist UNSCEAR in the preparation of the regular reports to the UN General Assembly and to serve Member States as a technical means for reporting and reviewing within the framework of the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management. The on-line version of the DIRATA database was deployed for the pilot application by Member States and the general public in 2006 and provides tools for: 1-)Input of the primary information by IAEA Member States and international organizations in batch or interactive (record by record) modes. The Microsoft Excel template is provided on the DIRATA website for the batch input; 2-) On-line access of Member States and the public to the dataset. The information contained in DIRATA is available for downloading (in CSV format) and interactive review. The new web-based version of DIRATA has inherited all of the important features contained on the previous CD-ROM versions, and has been extended by the number of principally new functionalities. The paper describes the structure, functionalities and content of the DIRATA database. (author)

The Members of the Agency

International Nuclear Information System (INIS)

1999-01-01

The document lists the 129 Member States of the Agency as of 1 June 1999. The new Member since the last issue of the list (INFCIRC/2/51) is Benin. The dates on which the present 129 states became Members, and the state (Honduras) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 43rd session of the General Conference are given in an Attachment

The Members of the Agency

International Nuclear Information System (INIS)

1998-01-01

The document lists the 128 Member States of the Agency as of 18 September 1998. The new Member since the last issue of the list (INFCIRC/2/50) is Burkina Faso. In an attachment the dates on which the present 128 states became Members, and the state (Benin) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 42nd session of the General Conference are given

The Members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-18

The document lists the 128 Member States of the Agency as of 18 September 1998. The new Member since the last issue of the list (INFCIRC/2/50) is Burkina Faso. In an attachment the dates on which the present 128 states became Members, and the state (Benin) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 42nd session of the General Conference are given

The Members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-16

The document lists the 129 Member States of the Agency as of 1 June 1999. The new Member since the last issue of the list (INFCIRC/2/51) is Benin. The dates on which the present 129 states became Members, and the state (Honduras) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 43rd session of the General Conference are given in an Attachment.

Thermal effects in concrete members

International Nuclear Information System (INIS)

Kar, A.K.

1977-01-01

The proposed method of analysis for concrete members subjected to temperature changes is consistent with the requirements of ultimate strength design. This also facilitates the provision of the same safety margin as for other loads. Due to cracks and creep in concrete, thermal stresses are nonlinear; they are dependent on the effective member stiffness, which in turn vary with the magnitude of loading. Therefore it is inconsistent to have an ultimate strength design in conjunction with an analysis based on the linear elastic theory. It is proposed that when the requirements of serviceability are met, the neutral axis corresponding to the ultimate load capacity conditions be considered for temperature-induced loadings. This conforms with the fact that the thermal load, because of creep and formation of cracks in the member, can be self-relieving as the failure load condition or ultimate capacity is approached. The maximum thermal load that can develop in dependent on the effective cross section of the member. Recommendations are made for determining the average effective member stiffness, which lies between the stiffness corresponding to the cracked (at ultimate condition) and the uncracked sections. In the proposed method, thermal stresses are not considered completely self-relieving. The stresses are considered simultaneously with stresses resulting from other causes. A step-by-step approach is presented for analysis and design of concrete members subjected to temperature changes

The members of the Agency

International Nuclear Information System (INIS)

1994-01-01

The new members since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.42) are: Armenia, Coratia, the Czech Republic, Lithuania, the Marshall Islands, the Slovak Republic and Uzbekistan. The Attachment to the circular shows the dates on which the 120 States became members of the Agency, as well as those States whose application for membership of the Agency was approved by the General Conference, but who have not yet deposited an instrument of acceptance of the Statute

The members of the Agency

International Nuclear Information System (INIS)

1998-01-01

The document lists the 127 Member States of the Agency as of 1 January 1998. The new Members since the last issue of of the list (INFCIRC/2/49) are Malta and the Republic of Moldova. In an attachment are given the dates on which the present 127 states become Members, the state (Burkina Faso) whose application for membership of the Agency has been approved by the General Conference but which has not deposited an instrument of acceptance of the Statute

The members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-01-15

The document lists the 127 Member States of the Agency as of 1 January 1998. The new Members since the last issue of of the list (INFCIRC/2/49) are Malta and the Republic of Moldova. In an attachment are given the dates on which the present 127 states become Members, the state (Burkina Faso) whose application for membership of the Agency has been approved by the General Conference but which has not deposited an instrument of acceptance of the Statute.

Extended thermodynamics

CERN Document Server

Müller, Ingo

1993-01-01

Physicists firmly believe that the differential equations of nature should be hyperbolic so as to exclude action at a distance; yet the equations of irreversible thermodynamics - those of Navier-Stokes and Fourier - are parabolic. This incompatibility between the expectation of physicists and the classical laws of thermodynamics has prompted the formulation of extended thermodynamics. After describing the motifs and early evolution of this new branch of irreversible thermodynamics, the authors apply the theory to mon-atomic gases, mixtures of gases, relativistic gases, and "gases" of phonons and photons. The discussion brings into perspective the various phenomena called second sound, such as heat propagation, propagation of shear stress and concentration, and the second sound in liquid helium. The formal mathematical structure of extended thermodynamics is exposed and the theory is shown to be fully compatible with the kinetic theory of gases. The study closes with the testing of extended thermodynamics thro...

Extended family medicine training

Science.gov (United States)

Slade, Steve; Ross, Shelley; Lawrence, Kathrine; Archibald, Douglas; Mackay, Maria Palacios; Oandasan, Ivy F.

2016-01-01

Abstract Objective To examine trends in family medicine training at a time when substantial pedagogic change is under way, focusing on factors that relate to extended family medicine training. Design Aggregate-level secondary data analysis based on the Canadian Post-MD Education Registry. Setting Canada. Participants All Canadian citizens and permanent residents who were registered in postgraduate family medicine training programs within Canadian faculties of medicine from 1995 to 2013. Main outcome measures Number and proportion of family medicine residents exiting 2-year and extended (third-year and above) family medicine training programs, as well as the types and numbers of extended training programs offered in 2015. Results The proportion of family medicine trainees pursuing extended training almost doubled during the study period, going from 10.9% in 1995 to 21.1% in 2013. Men and Canadian medical graduates were more likely to take extended family medicine training. Among the 5 most recent family medicine exit cohorts (from 2009 to 2013), 25.9% of men completed extended training programs compared with 18.3% of women, and 23.1% of Canadian medical graduates completed extended training compared with 13.6% of international medical graduates. Family medicine programs vary substantially with respect to the proportion of their trainees who undertake extended training, ranging from a low of 12.3% to a high of 35.1% among trainees exiting from 2011 to 2013. Conclusion New initiatives, such as the Triple C Competency-based Curriculum, CanMEDS–Family Medicine, and Certificates of Added Competence, have emerged as part of family medicine education and credentialing. In acknowledgment of the potential effect of these initiatives, it is important that future research examine how pedagogic change and, in particular, extended training shapes the care family physicians offer their patients. As part of that research it will be important to measure the breadth and uptake of

Scale-invariant extended inflation

International Nuclear Information System (INIS)

Holman, R.; Kolb, E.W.; Vadas, S.L.; Wang, Y.

1991-01-01

We propose a model of extended inflation which makes use of the nonlinear realization of scale invariance involving the dilaton coupled to an inflaton field whose potential admits a metastable ground state. The resulting theory resembles the Jordan-Brans-Dicke version of extended inflation. However, quantum effects, in the form of the conformal anomaly, generate a mass for the dilaton, thus allowing our model to evade the problems of the original version of extended inflation. We show that extended inflation can occur for a wide range of inflaton potentials with no fine-tuning of dimensionless parameters required. Furthermore, we also find that it is quite natural for the extended-inflation period to be followed by an epoch of slow-rollover inflation as the dilaton settles down to the minimum of its induced potential

Osteochondritis Dissecans Lesions in Family Members: Does a Positive Family History Impact Phenotypic Potency?

Science.gov (United States)

Gornitzky, Alex L; Mistovich, R Justin; Atuahuene, Brittany; Storey, Eileen P; Ganley, Theodore J

2017-06-01

Although repetitive microtrauma and athletic overuse patterns are most commonly associated with osteochondritis dissecans (OCD), recent studies have identified a potential genetic predisposition for OCD. Several case series have documented family pedigrees that support autosomal-dominant inheritance, but the families in these studies were all selected as a result of unique histories that may not accurately represent OCD inheritance patterns at large. Because there has been little investigation beyond these case reports, we aimed to describe a broader, more representative pattern of OCD inheritance applicable to all affected patients. (1) What proportion of patients treated for OCD of the knee have one or more immediate and/or extended family members with a history of OCD lesions? (2) Do patients with more phenotypically potent lesions, which we defined as patients with bilateral OCD lesions or patients who have undergone multiple procedures for OCD, have a higher frequency of affected relatives than those with less potent lesions? This retrospective study queried patient databases, diagnosis codes (International Classification of Diseases, 9th Revision), and surgical logs at a regional, tertiary care children's hospital to identify all patients treated over a 10-year period (March 2004-March 2014) by the senior author for OCD of the knee. All patients aged 0-18 years at the time of diagnosis were included. At our institution, patients with intact lesions are treated with a trial of conservative therapy; conversely, patients with a break in the articular cartilage and/or loose fragments of bone/cartilage are treated surgically. There were no OCD-specific contraindications to surgery. This search identified 543 patients. After patient identification, a questionnaire was designed that asked for the number, age, and gender of all immediate family members and the history of OCD lesions in any family member (immediate or extended). For all positive family members

Rational extended thermodynamics

CERN Document Server

Müller, Ingo

1998-01-01

Ordinary thermodynamics provides reliable results when the thermodynamic fields are smooth, in the sense that there are no steep gradients and no rapid changes. In fluids and gases this is the domain of the equations of Navier-Stokes and Fourier. Extended thermodynamics becomes relevant for rapidly varying and strongly inhomogeneous processes. Thus the propagation of high­ frequency waves, and the shape of shock waves, and the regression of small-scale fluctuation are governed by extended thermodynamics. The field equations of ordinary thermodynamics are parabolic while extended thermodynamics is governed by hyperbolic systems. The main ingredients of extended thermodynamics are • field equations of balance type, • constitutive quantities depending on the present local state and • entropy as a concave function of the state variables. This set of assumptions leads to first order quasi-linear symmetric hyperbolic systems of field equations; it guarantees the well-posedness of initial value problems and f...

Radiogenic leukemia risk analysis for the Techa River Cohort members

International Nuclear Information System (INIS)

Krestinina, L.Y.; Epifanova, S.B.; Akleyev, A.V.; Preston, D.; Davis, F.; Ron, E.

2008-01-01

Full text: Members of the Techa River Cohort have been exposed to a long-term external and internal irradiation due to releases of radioactive waste from the Mayak Production Association into the Techa River. Since internal exposure resulted primarily from incorporation of 90 Sr in the bone structure, the bone marrow was the principal target. The maximum dose to the red bone marrow accumulated over 50 years in cohort members reached 2 Gy, and the mean dose was 0.3 Gy. The epidemiological analysis of radiogenic risk of leukemia development was conducted based on the retrospective cohort study approach and regression analysis using the Epicure statistical packet. The extended Techa River Cohort (ETRC) includes about 30 thousand people of the two genders, various ages and different ethnicity (mostly Russians, Tartars and Bashkirs). The catchment area for leukemia mortality and incidence follow-up includes the whole Chelyabinsk and Kurgan Oblasts. The previous analysis of leukemia mortality risk for a 50-year follow-up period pointed out statistically significant dose dependence. The presentation will for the first time describe the results of leukemia incidence risk analyses for the period from 1953 through 2004. Over this 52-year follow-up period 92 leukemia cases (42 in men and 50 in women) were registered among ETRC members resident in the catchment area. Among those 92 cases there were 22 cases attributed to chronic lymphoid leukemia (12 in men and 10 in women). The preliminary analysis of leukemia incidence risk showed a statistically significant linear dependence on dose for total leukemias (p = 0.006), as well as for leukemias with CLL excluded (p < 0.001). The point value of the total leukemia incidence ERR was 2.0/Gy (95% CI: 0.4-15.4) and for leukemia with CLL excluded the ERR was 4.5/Gy (95% CI: 1.1-14.7). More than 57% of leukemia cases (excluding CLL) registered in ETRC members could be related to the radiogenic factor. Analyses of chronic lymphoid

The Members of the Agency

International Nuclear Information System (INIS)

1994-01-01

The new members since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.43) are: Kazakhstan and the former Yugoslav Republic of Macedonia. The Democratic People's Republic of Korea withdrew from membership of the Agency as of 13 June 1994. The Attachment hereto shows the dates on which the 121 States became members of the Agency, as well as those States whose application for membership of the Agency was approved by the General Conference, but who have not yet deposited an instrument of acceptance of the Statute

REGISTRATION OF VEHICLES IN SWITZERLAND: MEMBERS OF THE FAMILY OF A MEMBER OF THE PERSONNEL

CERN Multimedia

Service des Relations avec les Pays Hôtes

1999-01-01

The Permanent Mission of Switzerland to the International Organisations in Geneva has informed CERN that members of the family of a member of the personnel who hold a carte delégitimation or a Ci permit may not register a vehicle in Switzerland. Only those members of the family who are of Swiss nationality or hold an ordinary permit (e.g. a 'B' or 'C' permit) may register vehicles in their own names.Relations with the Host States Servicehttp://www.cern.ch/relations/Tel. 72848

International Focus: Highlighting APPA Members Worldwide

Science.gov (United States)

Glazner, Steve, Comp.

2011-01-01

While most APPA member institutions are located in the United States and Canada, there are also 45 of member institutions located internationally--from Australia and New Zealand to Southeast Asia to the Middle East to Europe. This article focuses on four of its international members: (1) American University of Kuwait (AUK); (2) American University…

International spinal cord injury endocrine and metabolic extended data set

DEFF Research Database (Denmark)

Bauman, W A; Wecht, J M; Biering-Sørensen, F

2017-01-01

findings in the SCI population. SETTING: This study was conducted in an international setting. METHODS: The ISCIEMEDS was developed by a working group. The initial ISCIEMEDS was revised based on suggestions from members of the International SCI Data Sets Committee, the International Spinal Cord Society......OBJECTIVE: The objective of this study was to develop the International Spinal Cord Injury (SCI) Endocrine and Metabolic Extended Data Set (ISCIEMEDS) within the framework of the International SCI Data Sets that would facilitate consistent collection and reporting of endocrine and metabolic...... (ISCoS) Executive and Scientific Committees, American Spinal Injury Association (ASIA) Board, other interested organizations, societies and individual reviewers. The data set was posted for two months on ISCoS and ASIA websites for comments. Variable names were standardized, and a suggested database...

Post-fire assessment of structural wood members

Science.gov (United States)

Robert J. Ross; Brian K. Brashaw; Xiping Wang; Robert H. White; Roy F. Pellerin

2005-01-01

Since the interior of a charred wood member normally retains its structural integrity, large structural wood members often do not need to be replaced after a fire. Engineering judgement is required to determine which members can remain and which members need to be replaced or repaired. Due to the lack of established methods to directly determine the residual capacity...

Materials Delivered by Member States

International Nuclear Information System (INIS)

1969-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 30 June 1969 in compliance with requests the Agency had made under Article IX. D

The Members of the Agency

International Nuclear Information System (INIS)

1997-01-01

The document lists the 125 Member States of the Agency as of 1 September 1997. The new Member since the last issue of the list (INFCIRC/2/Rev.48) is Latvia. In an Attachment are given the dates on which the present 125 States became Members, the State (Republic of Moldova) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States (Malta and Burkina Faso) whose applications for membership have been recommended by the Board of Governors for approval by the General Conference

The Members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-22

The document lists the 125 Member States of the Agency as of 1 September 1997. The new Member since the last issue of the list (INFCIRC/2/Rev.48) is Latvia. In an Attachment are given the dates on which the present 125 States became Members, the State (Republic of Moldova) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States (Malta and Burkina Faso) whose applications for membership have been recommended by the Board of Governors for approval by the General Conference.

19 CFR 122.75b - Electronic manifest requirement for crew members and non-crew members onboard commercial aircraft...

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Electronic manifest requirement for crew members... THE TREASURY AIR COMMERCE REGULATIONS Documents Required for Clearance and Permission To Depart; Electronic Manifest Requirements for Passengers, Crew Members, and Non-Crew Members Onboard Commercial...

Materials Delivered by Member States

International Nuclear Information System (INIS)

1975-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to 30 June 1975, in compliance with requests the Agency had made under Article IX. D

Materials Delivered by Member States

International Nuclear Information System (INIS)

1974-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to 31 March 1974, in compliance with requests the Agency had made under Article IX. D

Materials Delivered by Member States

International Nuclear Information System (INIS)

1971-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to the end of 1970, in compliance with requests the Agency had made under Article IX. D

Materials Delivered by Member States

International Nuclear Information System (INIS)

1973-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to the end of 1972, in compliance with requests the Agency had made under Article IX. D

Materials Delivered by Member States

International Nuclear Information System (INIS)

1972-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to the end of 1971, in compliance with requests the Agency had made under Article IX. D

Working with Difficult Group Members.

Science.gov (United States)

Kottler, Jeffrey A.

1994-01-01

Describes types of group members who are challenging in group settings including entitled, manipulative, and character-disordered clients. Provides suggestions for working with these group members, either as isolated cases or as homogenous populations, emphasizing the protection of other clients' rights. Includes 31 references. (Author/CRR)

APPARATUS FOR NON-DESTRUCTIVE INSPECTION OF CANTILEVERED MEMBERS

Science.gov (United States)

Taylor, E.R.; Mahoney, C.H.; Lay, C.R.

1961-10-24

An apparatus for non-destructive inspection of cantilevered members, such as compressor blades, is described. The member under inspection is vibrated with a regulated source of air under pressure. The amplitude of vibration of the member is maintained at its natural frequency. The frequency of vibration of the member is measured. An indication of an excessive decay or erratic shifting in the measured frequency above an allowable hysteretic decay is provided as an indication of a fault in the member. The member is vibrated for a selected test period. (AEC)

Extended spider cognition.

Science.gov (United States)

Japyassú, Hilton F; Laland, Kevin N

2017-05-01

There is a tension between the conception of cognition as a central nervous system (CNS) process and a view of cognition as extending towards the body or the contiguous environment. The centralised conception requires large or complex nervous systems to cope with complex environments. Conversely, the extended conception involves the outsourcing of information processing to the body or environment, thus making fewer demands on the processing power of the CNS. The evolution of extended cognition should be particularly favoured among small, generalist predators such as spiders, and here, we review the literature to evaluate the fit of empirical data with these contrasting models of cognition. Spiders do not seem to be cognitively limited, displaying a large diversity of learning processes, from habituation to contextual learning, including a sense of numerosity. To tease apart the central from the extended cognition, we apply the mutual manipulability criterion, testing the existence of reciprocal causal links between the putative elements of the system. We conclude that the web threads and configurations are integral parts of the cognitive systems. The extension of cognition to the web helps to explain some puzzling features of spider behaviour and seems to promote evolvability within the group, enhancing innovation through cognitive connectivity to variable habitat features. Graded changes in relative brain size could also be explained by outsourcing information processing to environmental features. More generally, niche-constructed structures emerge as prime candidates for extending animal cognition, generating the selective pressures that help to shape the evolving cognitive system.

Paradoxical role of an Egr transcription factor family member, Egr2/Krox20, in learning and memory

Directory of Open Access Journals (Sweden)

Roseline Poirier

2007-12-01

Full Text Available It is well established that Egr1/zif268, a member of the Egr family of transcription factors, is critical for the consolidation of several forms of memories. Recently, the Egr3 family member has also been implicated in learning and memory. Because Egr family members encode closely related zinc-finger transcription factors sharing a highly homologous DNA binding domain that recognises the same DNA sequence, they may have related functions in brain. Another Egr family member expressed in brain, Egr2/Krox20 is known to be crucial for normal hindbrain development and has been implicated in several inherited peripheral neuropathies; however, due to Egr2-null mice perinatal lethality, its potential role in cognitive functions in the adult has not been yet explored. Here, we generated Egr2 conditional mutant mice allowing postnatal, forebrain-specific Cre-mediated Egr2 excision and tested homozygous, heterozygous and control littermates on a battery of behavioural tasks to evaluate motor capacity, exploratory behaviour, emotional reactivity and learning and memory performance in spatial and non-spatial tasks. Egr2-deficient mice had no sign of locomotor, exploratory or anxiety disturbances. Surprisingly, they also had no impairment in spatial learning and memory, taste aversion memory or fear memory using a trace conditioning paradigm. On the contrary, Egr2-deficient mice had improved performance in motor learning on a rotarod, and in object recognition memory. These results clearly do not extend the phenotypic consequences resulting from either Egr1 or Egr3 loss-of-function to Egr2. In contrast, they indicate that Egr family members may have different, and in certain circumstances antagonistic functions in the adult brain.

Extending the horizons advances in computing, optimization, and decision technologies

CERN Document Server

Joseph, Anito; Mehrotra, Anuj; Trick, Michael

2007-01-01

Computer Science and Operations Research continue to have a synergistic relationship and this book represents the results of cross-fertilization between OR/MS and CS/AI. It is this interface of OR/CS that makes possible advances that could not have been achieved in isolation. Taken collectively, these articles are indicative of the state-of-the-art in the interface between OR/MS and CS/AI and of the high caliber of research being conducted by members of the INFORMS Computing Society. EXTENDING THE HORIZONS: Advances in Computing, Optimization, and Decision Technologies is a volume that presents the latest, leading research in the design and analysis of algorithms, computational optimization, heuristic search and learning, modeling languages, parallel and distributed computing, simulation, computational logic and visualization. This volume also emphasizes a variety of novel applications in the interface of CS, AI, and OR/MS.

Extended mind and after: socially extended mind and actor-network.

Science.gov (United States)

Kono, Tetsuya

2014-03-01

The concept of extended mind has been impressively developed over the last 10 years by many philosophers and cognitive scientists. The extended mind thesis (EM) affirms that the mind is not simply ensconced inside the head, but extends to the whole system of brain-body-environment. Recently, some philosophers and psychologists try to adapt the idea of EM to the domain of social cognition research. Mind is socially extended (SEM). However, EM/SEM theory has problems to analyze the interactions among a subject and its surroundings with opposition, antagonism, or conflict; it also tends to think that the environment surrounding the subject is passive or static, and to neglect the power of non-human actants to direct and regulate the human subject. In these points, actor-network theory (ANT) proposed by Latour and Callon is more persuasive, while sharing some important ideas with EM/SEM theory. Actor-network is a hybrid community which is composed of a series of heterogeneous elements, animate and inanimate for a certain period of time. I shall conclude that EM/SEM could be best analyzed as a special case of actor-network. EM/SEM is a system which can be controlled by a human agent alone. In order to understand collective behavior, philosophy and psychology have to study the actor-network in which human individuals are situated.

Finding Street Gang Members on Twitter

OpenAIRE

Balasuriya, Lakshika; Wijeratne, Sanjaya; Doran, Derek; Sheth, Amit

2016-01-01

Most street gang members use Twitter to intimidate others, to present outrageous images and statements to the world, and to share recent illegal activities. Their tweets may thus be useful to law enforcement agencies to discover clues about recent crimes or to anticipate ones that may occur. Finding these posts, however, requires a method to discover gang member Twitter profiles. This is a challenging task since gang members represent a very small population of the 320 million Twitter users. ...

Administrative Circular No. 2 (Rev. 7) - Recruitment, appointment and possible developments regarding the contractual position of staff members

CERN Multimedia

2015-01-01

Administrative Circular No. 2 (Rev. 7), entitled "Recruitment, appointment and possible developments regarding the contractual position of staff members", approved by the Director-General following discussion at the Standing Concertation Committee meeting held on 17 February 2015 is available via the following link: AC No. 2 (Rev.7).   This revised circular cancels and replaces Administrative Circular No. 2 (Rev. 6), entitled "Recruitment, appointment and possible developments regarding the contractual position of staff members" and dated January 2015. The circular was revised in order to implement the amendment to Article R II 1.17 of the Staff Regulations, which introduces the possibility of extending limited-duration (LD) contracts up to a maximum total duration of eight years from the previous duration of five years. The award of indefinite contracts will continue to be subject to the outcome of a competitive process. Department Head Of...

Self-esteem and in-group bias among members of a religious social category.

Science.gov (United States)

Hunter, J A

2001-06-01

In a sample of New Zealand university students, the author extended earlier research into the relationship between self-esteem and intergroup discrimination. He found no support for the hypothesis that social-category members (i.e., Christians) experience an elevation in the domain of self-esteem (i.e., religious self-esteem) judged as more relevant to the in-group after evaluations favoring the in-group. Regardless of whether the evaluation targets behaved positively or negatively, the respondents in the experimental condition evaluated in-group (Christian) targets more highly than out-group (Atheist) targets. After evaluations favoring the in-group, the respondents did not experience an elevation of religious self-esteem, global self-esteem, or mathematical self-esteem (judged as less relevant to the in-group).

Integration of an Inter Turbine Burner to a Jet Turbine Engine

Science.gov (United States)

2013-03-01

Technology AFRL = Air Force Research Laboratory EGV = Exit Guide Vane HPT = High-Pressure Turbine ID = Inner Diameter IGV = Inlet Guide Vane...been able to show computationally that the compressor exit guide vane (EGV) and the turbine inlet guide vane ( IGV ) could be combined into a single...turbine engine hot section. The red slashed out sections are, from left to right, the compressor exit vane, HPT IGV , and the stator between the HPT and

Extended producer responsibility: The impact of organizational dimensions on WEEE collection from households.

Science.gov (United States)

Corsini, Filippo; Rizzi, Francesco; Frey, Marco

2017-01-01

Extended Producer Responsibility (EPR) has been the backbone of product life cycle management in Europe since the 2000s. Unfortunately, EPR implementation has multiple impacts on the supply chain and, thus, its consequences are not always easily manageable. Although several studies have explored various examples within the EU, the determinants of the effectiveness of EPR management are still not fully understood. This research seeks to bridge this gap by making use of quantitative analyses to investigate how key issues related to: WEEE Directive transposition and organizational settings adopted by each Member State, influenced the results achieved in those Member States in terms of collection from households. In details, a latent class analysis (LCA) has been used to analyse different EPR management strategies based on the policy set, the supply chain structure, and the performance of the household collection of electronic waste. Results highlight the strong connection between allocation of responsibility and organizational model adopted in Member States and performance related to small households equipment's. Conclusions shows the need for stronger coordination of EPR and waste policies in order to achieve adequate levels of Waste Electrical and Electronic Equipment (WEEE) collection, the need of a clear delineation of the responsibilities of each subject of the supply chain and also the importance of "clearing houses" in moderating the impacts of short-sighted competition between collective schemes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Experimental Investigation of a Forward Swept Rotor in a Multistage Fan with Inlet Distortion

Directory of Open Access Journals (Sweden)

Aspi R. Wadia

2011-01-01

Full Text Available Previous studies of transonic swept rotors in single stage fans have demonstrated the potential of significant improvements in both efficiency and stall margin with forward swept blading. This paper extends the assessment of the payoff derived from forward sweep to multistage configurations. The experimental investigation compare two builds of an advanced two-stage fan configuration tested alternately with a radial and a forward swept stage 1 blade. In the two-stage evaluations, the testing was extended to include the effect on inlet flow distortion. While the common second stage among the two builds prevented the overall fan from showing clean inlet performance and stability benefits with the forward swept rotor 1, this configuration did demonstrate superior front stage efficiency and tolerance to inlet distortion. Having obtained already low distortion sensitivity with the radial rotor 1 configuration relative to current production military fan standards, the sensitivity to inlet distortion was halved with the forward swept rotor 1 configuration. In the case of the 180-degree one-per-rev distortion pattern, the two-stage configuration was evaluated both with and without inlet guide vanes (IGVs. The presence of the inlet guide vanes had a profound impact in lowering the two-stage fan's sensitivity with inlet distortion.

The Extended Enterprise concept

DEFF Research Database (Denmark)

Larsen, Lars Bjørn; Vesterager, Johan; Gobbi, Chiara

1999-01-01

This paper provides an overview of the work that has been done regarding the Extended Enterprise concept in the Common Concept team of Globeman 21 including references to results deliverables concerning the development of the Extended Enterprise concept. The first section presents the basic concept...... picture from Globeman21, which illustrates the Globeman21 way of realising the Extended Enterprise concept. The second section presents the Globeman21 EE concept in a life cycle perspective, which to a large extent is based on the thoughts and ideas behind GERAM (ISO/DIS 15704)....

Extended Enterprise performance Management

NARCIS (Netherlands)

Bobbink, Maria Lammerdina; Hartmann, Andreas

2014-01-01

The allegiance of partnering organisations and their employees to an Extended Enterprise performance is its proverbial sword of Damocles. Literature on Extended Enterprises focuses on collaboration, inter-organizational integration and learning to avoid diminishing or missing allegiance becoming an

Perspectives and expectations of union member and non- union member teachers on teacher unions

Directory of Open Access Journals (Sweden)

Tuncer FİDAN

2015-12-01

Full Text Available Unions, which can be regarded as one of the constitutive elements of democracy, are the pressure groups in political and social fields. Unions were born out of industrial confrontations and expanded into the field of public services over time, and thus teachers – who are also public employees-, also obtained the right to establish and affiliate to unions. In this research the views of union member and non-union member teachers on the most important functions and operational effectiveness of unions, teachers’ expectations from unions and teachers’ evaluation of the solidarity, competition and cooperation between unions were determined and the perspectives of teachers on unionization were revealed. qualitative research design was used. The data needed were collected through semi-structured interviews from volunteering union member and non-union member teachers who were working in the primary and secondary schools in Ankara province and who were selected through “maximum variation sampling approach”. The data were then analyzed by using the content analysis technique. In conclusion, it was found that political ideology was the most important reason for membership of teachers’ unions. Protection and development of personal rights was found to be the most important function of teacher unions and unions were thought to be insufficient in performing those functions.

Burnout in Female Faculty Members.

Science.gov (United States)

Cassidy-Vu, Lisa; Beck, Keli; Moore, Justin B

2017-04-01

Despite approximately equal numbers of male and female medical school graduates, women are entering academic medicine at a lower rate than their male colleagues. Of those who do assume a faculty position, female faculty members report higher levels of burnout, often attributable to gender-specific difficulties in clinical expectations and maintenance of work-life balance. Many of these struggles are attributable to issues that are amenable to supportive policies, but these policies are inconsistent in their availability and practice. This commentary presents evidence for inconsistencies in the day-to-day experience of female faculty members, and proposes solutions for the mitigation of the challenges experienced more often by female faculty members with the goal of diversifying and strengthening academic medicine.

45 CFR 703.9 - Reimbursement of members.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 3 2010-10-01 2010-10-01 false Reimbursement of members. 703.9 Section 703.9... AND FUNCTIONS OF STATE ADVISORY COMMITTEES § 703.9 Reimbursement of members. (a) Advisory Committee members may be reimbursed by the Commission by a per diem subsistence allowance and for travel expenses at...

Family members' involvement in elder care provision in nursing homes and their considerations about financial compensation: a qualitative study.

Science.gov (United States)

Habjanič, Ana; Pajnkihar, Majda

2013-01-01

The aim of this study was to establish how family members are involved in elder care provision in nursing homes; this included research into their feelings about potentially extending their involvement to obtain financial benefits as compensation for high accommodation costs. Family members remain involved in the caring process after their relatives have been admitted to an institution. On average, accommodation costs in nursing homes in Slovenia have risen above the residents' retirement pension, and families must supplement the difference. Because of this, familial involvement should be linked to reduced accommodation costs. This research employed a non-experimental, descriptive study design through unstructured interviews. Participants included fifty family members (n=50) who visit their relatives in nursing homes. Data were collected in 2010 at five nursing homes in Slovenia and processed by means of conventional content analysis. The major themes that emerged from the content analysis, describing family involvement, were as follows: visiting and making oneself useful, delivery of items for personal use, hands-on care, physical therapy and organization of nursing home activities. Family members showed some interest in receiving financial compensation for their involvement. The proposed financial compensation may be a delicate and morally questionable matter but would involve fairness and transparency, while enabling easier organization of elder care provision. Eventually, nursing home residents' well-being could be improved. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Rates of opioid dispensing and overdose after introduction of abuse-deterrent extended-release oxycodone and withdrawal of propoxyphene.

Science.gov (United States)

Larochelle, Marc R; Zhang, Fang; Ross-Degnan, Dennis; Wharam, J Frank

2015-06-01

In the second half of 2010, abuse-deterrent extended-release oxycodone hydrochloride (OxyContin; Purdue Pharma) was introduced and propoxyphene was withdrawn from the US market. The effect of these pharmaceutical market changes on opioid dispensing and overdose rates is unknown. To evaluate the association between 2 temporally proximate changes in the opioid market and opioid dispensing and overdose rates. Claims from a large national US health insurer were analyzed, using an interrupted time series study design. Participants included an open cohort of 31.3 million commercially insured members aged 18 to 64 years between January 1, 2003, and December 31, 2012, with median follow-up of 20 months (last follow-up, December 31, 2012). Introduction of abuse-deterrent OxyContin (resistant to crushing or dissolving) on August 9, 2010, and market withdrawal of propoxyphene on November 19, 2010. Standardized opioid dispensing rates and prescription opioid and heroin overdose rates were the primary outcomes. We used segmented regression to analyze changes in outcomes from 30 quarters before to 8 quarters after the 2 interventions. Two years after the opioid market changes, total opioid dispensing decreased by 19% from the expected rate (absolute change, -32.2 mg morphine-equivalent dose per member per quarter [95% CI, -38.1 to -26.3]). By opioid subtype, the absolute change in dispensing by milligrams of morphine-equivalent dose per member per quarter at 2 years was -11.3 (95% CI, -12.4 to -10.1) for extended-release oxycodone, 3.26 (95% CI, 1.40 to 5.12) for other long-acting opioids, -8.19 (95% CI, -9.30 to -7.08) for propoxyphene, and -16.2 (95% CI, -18.8 to -13.5) for other immediate-release opioids. Two years after the market changes, the estimated overdose rate attributed to prescription opioids decreased by 20% (absolute change, -1.10 per 100,000 members per quarter [95% CI, -1.47 to -0.74]), but heroin overdose increased by 23% (absolute change, 0.26 per 100

Experimental study of complex flow and turbulence structure around a turbomachine rotor blade operating behind a row of Inlet Guide Vanes (IGVS)

Science.gov (United States)

Soranna, Francesco

The flow and turbulence around a rotor blade operating downstream of a row of Inlet Guide Vanes (IGV) are investigated experimentally in a refractive index matched turbomachinery facility that provides unobstructed view of the entire flow field. High resolution 2D and Stereoscopic PIV measurements are performed both at midspan and in the tip region of the rotor blade, focusing on effects of wake-blade, wake-boundary-layer and wake-wake interactions. We first examine the modification to the shape of an IGV-wake as well as to the spatial distribution of turbulence within it as the wake propagates along the rotor blade. Due to the spatially non-uniform velocity distribution, the IGV wake deforms through the rotor passage, expanding near the leading edge and shrinking near the trailing edge. The turbulence within this wake becomes spatially non-uniform and highly anisotropic as a result of interaction with the non-uniform strain rate field within the rotor passage. Several mechanisms, which are associated with rapid straining and highly non-uniform production rate (P), including negative production on the suction side of the blade, contribute to the observed trends. During IGV-wake impingement, the suction side boundary layer near the trailing edge becomes significantly thinner, with lower momentum thickness and more stable profile compared to other phases at the same location. Analysis of available terms in the integral momentum equation indicates that the phase-averaged unsteady term is the main contributor to the decrease in momentum thickness within the impinging wake. Thinning of the boundary/shear layer extends into the rotor near wake, making it narrower and increasing the phase averaged shear velocity gradients and associated production term just downstream of the trailing edge. Consequently, the turbulent kinetic energy (TKE) increases causing as much as 75% phase-dependent variations in peak TKE magnitude. Further away from the blade, the rotor wake is bent

Migration processes in SCO member states

Directory of Open Access Journals (Sweden)

Valentina Sergeevna Antonyuk

2012-12-01

Full Text Available The article concerns modern state and development of migration processes in SCO member states. As a main method of research statistical analysis was applied. The article shows that migration streams between SCO member states are rather intensive, and the problem of labor migration becomes more and more urgent. The countries of consuming and supplying of labour force are clearly differentiated in the region. For some countries, labor export is the key sector of economy. At the same time, interstate relations between SCO member states sometimes are rather disputed. The most urgent factors causing the development of migration processes in the region were determined. Among them, thefactor of growing outflows from China isespecially noted. It is noted that migration processes are discussed by SCO member states nowadays in terms of illegal migration and international criminality connected with it. It means that the question of labor migration is a real problem. It is indicated that the creation of a specific joint commission on migration policy affiliated with the Council of Foreign Ministers of SCO member states is the necessary condition of effective interaction in migration questions within the framework of Shanghai Cooperation Organization.

The Members of the Agency (French Edition)

International Nuclear Information System (INIS)

2013-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.74) is Swaziland, which deposited its instrument of acceptance of the Statute on 15 February 2013. The Attachment hereto shows the dates on which the present 159 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government

The Members of the Agency (Spanish Edition)

International Nuclear Information System (INIS)

2013-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.74) is Swaziland, which deposited its instrument of acceptance of the Statute on 15 February 2013. The Attachment hereto shows the dates on which the present 159 Member States deposited instruments of ratification or acceptance of the Statute with the depositary Government

The Text of the Fourth Agreement to Extend the 1987 Regional Co-operative Agreement for Research, Development and Training related to Nuclear Science and Technology (RCA). Extension of Agreement. Latest Status

International Nuclear Information System (INIS)

2007-01-01

The text of the Fourth Agreement to Extend the 1987 Regional Co-operative Agreement for Research, Development and Training Related to Nuclear Science and Technology, 'the 1987 RCA', is reproduced herein for the information of all Members

Flame-Resistant Composite Materials For Structural Members

Science.gov (United States)

Spears, Richard K.

1995-01-01

Matrix-fiber composite materials developed for structural members occasionally exposed to hot, corrosive gases. Integral ceramic fabric surface layer essential for resistance to flames and chemicals. Endures high temperature, impedes flame from penetrating to interior, inhibits diffusion of oxygen to interior where it degrades matrix resin, resists attack by chemicals, helps resist erosion, and provides additional strength. In original intended application, composite members replace steel structural members of rocket-launching structures that deteriorate under combined influences of atmosphere, spilled propellants, and rocket exhaust. Composites also attractive for other applications in which corrosion- and fire-resistant structural members needed.

When the grace period is over: Assessing the new Member States' compliance with EU requirements for oil stockholding

International Nuclear Information System (INIS)

Tosun, Jale

2011-01-01

The accumulation of appropriate emergency stocks of crude oil and petroleum products has been at the heart of the European Commission's efforts to increase the security of supply. This study investigates how effectively the 'new' Member States comply with the requirements of Council Directive 2006/67/EC, which imposes the obligation to maintain minimum stocks of crude oil and/or petroleum products. The empirical focus of this analysis is not only motivated by the practical relevance of this issue, but also by the fact that eleven of the twelve new Member States were given grace periods between one and seven years to bring their national stockholding arrangements in line with the European requirements. The granting of extended deadlines raises the question whether this instrument indeed facilitates the transposition process. The empirical findings show that except for Latvia, compliance with the EU stockholding requirements is generally very good. A more detailed analysis of the Latvian case highlights that the transposition delays principally stem from budgetary constraints. More generally, the individual new Member States' capacity to cope with the financial burdens and the degree of adjustment pressure determine the variation in oil stock levels. - Highlights: → Compliance with Council Directive 2006/67/EC is generally very good in the new Member States. → Solely Latvia faces difficulties in developing adequate oil stock levels. → Latvia's insufficient compliance can be attributed to severe budgetary constraints. → Financial capacity and adjustment pressure determine cross-country variation in stock levels.

The use of virtual reality in the military's assessment of service members with traumatic brain injury: recent developments and emerging opportunities.

Science.gov (United States)

Edwards, Joe; Vess, James; Reger, Greg; Cernich, Alison

2014-01-01

Traumatic brain injury (TBI) is a common event in the current extended conflicts by American service members, with estimates that as many as 300,000 have sustained combat-related concussions during Operation Iraqi Freedom and Operation Enduring Freedom. The limited ecological validity of traditional neuropsychological assessment measures presents a challenge to effective postconcussion evaluation of service members in relation to fitness-for-duty decisions or rehabilitation needs. Virtual reality (VR) technology offers a promising opportunity to advance the field of functional assessment for TBI. This article reviews the current professional literature on VR applications for TBI assessment, with special emphasis on those that are particularly relevant to U.S. service members. VR affords several advantages for clinical use. These include assessment of complex sets of cognitive and behavioral functions rather than the isolated components assessed by traditional measures; more precise control over the standardized presentation of task stimuli and the recording of response data; and enhanced ecological validity that can lead to more useful assessment data in the applied contexts faced by the U.S. military.

Nurses' turnover intention: The impact of leader-member exchange, organizational identification and job embeddedness.

Science.gov (United States)

Dechawatanapaisal, Decha

2018-06-01

The aim of this study was to examine the influence of three factors on turnover intention: leader-member exchange quality, organizational identification and job embeddedness. This area of inquiry has not been fully investigated in the literature. Employee turnover, particularly of professionals, becomes a very challenging issue. It continually affects organizations in terms of resourcing and developmental costs, manpower instability, day-to-day operations, perception of quality care and efficiency. Therefore, employees' working attitude and behaviour have drawn increasing attention for further research to determine which factors keep them with their employer. A cross-sectional survey was conducted with self-report questionnaires. Data were collected from 1,966 nurses from sixteen private general hospitals in Thailand during February-June 2016. Hypotheses were tested and analysed by means of a confirmatory factor analysis, structural equation modelling and a bootstrapping procedure. The results revealed the direct relationship between leader-member exchange quality and job embeddedness. Organizational identification played an intermediary role that partially mediated the relationship between leader-member exchange quality on job embeddedness. Analysis also provided support for the mediating effect of organizational identification and turnover intention through job embeddedness. This study extends the job embeddedness theory and gains understanding of the antecedent factors that directly and indirectly cause employees to become embedded and lead to predict turnover intention. The findings are pertinent, as few studies have investigated such relationships. The implications provide insights into how organizations can better retain their workforce. © 2018 John Wiley & Sons Ltd.

Leader-member exchange (LMX) and innovation climate: the role of LMX differentiation.

Science.gov (United States)

Tordera, Núria; González-Romá, Vicente

2013-01-01

Leader-member Exchange (LMX) theory has been shown to be one of the most compelling theories for understanding the effects of leadership on organizational behavior. This theory proposes that leaders establish differentiated relationships with each of their subordinates according to the exchanges produced between them. Recently, the concept of LMX differentiation has been introduced into the theory to extend research from the dyadic to the group level. The present paper uses a longitudinal design to analyze the moderator role of LMX differentiation in the relationship between mean LMX and innovation climate in a sample of 24 healthcare teams. The results showed no direct effects of mean LMX on changes in innovation climate over time. However, they provide support for the moderator effect of LMX differentiation in this relationship, as it was stronger when LMX differentiation was low than when it was high.

The Text of the Fourth Agreement to Extend the 1987 Regional Co-operative Agreement for Research, Development and Training related to Nuclear Science and Technology (RCA). Extension of Agreement. Latest Status

International Nuclear Information System (INIS)

2007-01-01

The text of the Fourth Agreement to Extend the 1987 Regional Co-operative Agreement for Research, Development and Training Related to Nuclear Science and Technology, 'the 1987 RCA', is reproduced herein for the information of all Members [es

The symmetric extendibility of quantum states

International Nuclear Information System (INIS)

Nowakowski, Marcin L

2016-01-01

Studies on the symmetric extendibility of quantum states have become particularly important in the context of the analysis of one-way quantum measures of entanglement, and the distillability and security of quantum protocols. In this paper we analyze composite systems containing a symmetric extendible part, with particular attention devoted to the one-way security of such systems. Further, we introduce a new one-way entanglement monotone based on the best symmetric approximation of a quantum state and the extendible number of a quantum state. We underpin these results with geometric observations about the structures of multi-party settings which posses substantial symmetric extendible components in their subspaces. The impossibility of reducing the maximal symmetric extendibility by means of the one-way local operations and classical communication method is pointed out on multiple copies. Finally, we state a conjecture linking symmetric extendibility with the one-way distillability and security of all quantum states, analyzing the behavior of a private key in the neighborhood of symmetric extendible states. (paper)

Static Members of Classes in C#

Directory of Open Access Journals (Sweden)

Adrian LUPASC

2017-12-01

Full Text Available The C# language is object-oriented, which is why the declared member data must be part of a class. Thus, there is no possibility to declare certain variables that can be accessed from anywhere within the application, as it happens, for example, with global variables at the C language level. Making this work in C# is possible through static members of the class. Declaring a class implies defining some of its member data that later receive values when creating each object. A static member of the class can be interpreted as belonging only to the class, not to the objects subsequently created, which means that for the non-static data, there are as many children as there were objects created, while for the static ones there is only one copy, regardless of the number of created objects. In this regard, this paper presents the main aspects that characterize these abstract concepts of object oriented programming in general and C# language in particular, detailing how to develop an application that includes both static and non-static members. At the same time, particularities in the mirror for the two types of data, restrictions on use and potential limitations are presented.

The amazing vanishing Canadian dermatologist: results from the 2006 Canadian Dermatology Association member survey.

Science.gov (United States)

Chow, Eunice Y; Searles, Gordon E

2010-01-01

The 2006 Canadian Dermatology Association (CDA) member survey tracked the Canadian dermatology workforce. Information on use of nondermatologist extenders, impact of financial burden on practice style, and wait times was collected in the survey. To survey Canadian dermatologists for specialty-specific physician resource information including demographics, workload, and future career plans and compare it to results from the 2001 survey. In addition, to explore three other areas not covered in the previous survey: patient access to dermatologic care through wait times, the use of nondermatologist extenders, and potential impact of educational financial debt on practice styles. CDA members in 2006 were surveyed by mail. Follow-up mailings were done for nonresponders. Survey results were compared to those of the 2001 survey. Thirty-six percent (216 of 602) of Canadian dermatologists responded (70% in 2001). The national distribution was identical between surveys. The median age increased to 55 years; two-thirds of dermatologists are male. The median retirement age remained at 65 years. There was a shift from rural to urban practice locations; 78% practice in private offices. Three-fifths of dermatologists do mainly medical dermatology, a decrease between surveys. Pediatric dermatology decreased 10%, whereas surgical dermatology increased 52% between surveys. Fewer practitioners perform noninsured services, and half as many perform research or hospital consultations or teach medical students. Financial debt burden had no impact on selection of practice style. Median wait times for nonurgent consultations doubled from 5 to 10 weeks; follow-up visits increased from 4 to 5 weeks; noninsured consultations increased from 4 to 5 weeks. The national median wait time for a third available consultation appointment was 42 days (range 7-161 days). Seventeen percent of dermatologists reported using nondermatologist extenders. Training programs produce only 60% of new practitioners

The Text of the Third Agreement to Extend the 1987 Regional Co-operative Agreement for Research, Development and Training related to Nuclear Science and Technology (RCA). Latest Status. Extension of Agreement

International Nuclear Information System (INIS)

2002-01-01

The text of the Third Agreement to Extend the 1987 Regional Co-operative Agreement for Research, Development and Training Related to Nuclear Science and Technology, t he 1987 RCA , is reproduced herein for the information of all Members [es

Extended likelihood inference in reliability

International Nuclear Information System (INIS)

Martz, H.F. Jr.; Beckman, R.J.; Waller, R.A.

1978-10-01

Extended likelihood methods of inference are developed in which subjective information in the form of a prior distribution is combined with sampling results by means of an extended likelihood function. The extended likelihood function is standardized for use in obtaining extended likelihood intervals. Extended likelihood intervals are derived for the mean of a normal distribution with known variance, the failure-rate of an exponential distribution, and the parameter of a binomial distribution. Extended second-order likelihood methods are developed and used to solve several prediction problems associated with the exponential and binomial distributions. In particular, such quantities as the next failure-time, the number of failures in a given time period, and the time required to observe a given number of failures are predicted for the exponential model with a gamma prior distribution on the failure-rate. In addition, six types of life testing experiments are considered. For the binomial model with a beta prior distribution on the probability of nonsurvival, methods are obtained for predicting the number of nonsurvivors in a given sample size and for predicting the required sample size for observing a specified number of nonsurvivors. Examples illustrate each of the methods developed. Finally, comparisons are made with Bayesian intervals in those cases where these are known to exist

25 CFR 1000.18 - May a Consortium member Tribe withdraw from the Consortium and become a member of the applicant...

Science.gov (United States)

2010-04-01

...-governance activities for a member Tribe, that planning activity and report may be used to satisfy the planning requirements for the member Tribe if it applies for self-governance status on its own. (b) Submit... for Participation in Tribal Self-Governance Eligibility § 1000.18 May a Consortium member Tribe...

21 CFR 13.10 - Members of a Board.

Science.gov (United States)

2010-04-01

... BEFORE A PUBLIC BOARD OF INQUIRY General Provisions § 13.10 Members of a Board. (a) All members of a... to be free from bias or prejudice concerning the issues involved. A member of a Board may be a full...

Extended Year, Extended Contracts: Increasing Teacher Salary Options.

Science.gov (United States)

Gandara, Patricia

1992-01-01

Reports on an attempt to raise teacher salaries through an extended contract made possible through year-round school schedules. Teacher satisfaction with the 1987 experiment in three California schools (the Orchard Plan) has been high. Elements that have contributed to job satisfaction are discussed. (SLD)

Bibliometric analysis of anaesthesia journal editorial board members: correlation between journal impact factor and the median h-index of its board members.

Science.gov (United States)

Pagel, P S; Hudetz, J A

2011-09-01

h-index is useful for quantifying scholarly activity in medicine, but this statistic has not been extensively applied as a measure of productivity in anaesthesia. We conducted a bibliometric analysis of h-index in editorial board members and tested the hypothesis that editorial board members of anaesthesia journals with higher impact factors (IFs) have higher h-indices. Ten of 19 journals with 2009 IF>1 were randomly chosen from Journal Citation Reports(®). Board members were identified using each journal's website. Publications, citations, citations per publication, and h-index for each member were obtained using Scopus(®). Four hundred and twenty-three individuals filled 481 anaesthesia editorial board positions. The median h-index of all editorial board members was 14. Board members published 75 papers (median) with 1006 citations and 13 citations per publication. Members serving on journals with IF greater than median had significantly (Pcitations, and citations per publication than those at journals with IF less than median. A significant correlation between the median h-index of a journal's editorial board members and its IF (h-index=3.01×IF+6.85; r( 2)=0.452; P=0.033) was observed for the 10 journals examined. Board members of subspeciality-specific journals had bibliometric indices that were less than those at general journals. The h-index was greater in individuals serving more than one journal. European editorial board members had higher h-index values than their American colleagues. The results suggest that editorial board members of anaesthesia journals with higher IFs have higher h-indices.

A Novel Biped Pattern Generator Based on Extended ZMP and Extended Cart-Table Model

Directory of Open Access Journals (Sweden)

Guangbin Sun

2015-07-01

Full Text Available This paper focuses on planning patterns for biped walking on complex terrains. Two problems are solved: ZMP (zero moment point cannot be used on uneven terrain, and the conventional cart-table model does not allow vertical CM (centre of mass motion. For the ZMP definition problem, we propose the extended ZMP (EZMP concept as an extension of ZMP to uneven terrains. It can be used to judge dynamic balance on universal terrains. We achieve a deeper insight into the connection and difference between ZMP and EZMP by adding different constraints. For the model problem, we extend the cart-table model by using a dynamic constraint instead of constant height constraint, which results in a mathematically symmetric set of three equations. In this way, the vertical motion is enabled and the resultant equations are still linear. Based on the extended ZMP concept and extended cart-table model, a biped pattern generator using triple preview controllers is constructed and implemented simultaneously to three dimensions. Using the proposed pattern generator, the Atlas robot is simulated. The simulation results show the robot can walk stably on rather complex terrains by accurately tracking extended ZMP.

Comprehensive Forced Response Analysis of J2X Turbine Bladed-Discs with 360 Degree Variation in CFD Loading

Science.gov (United States)

Elrod, David; Christensen, Eric; Brown, Andrew

2011-01-01

The temporal frequency content of the dynamic pressure predicted by a 360 degree computational fluid dynamics (CFD) analysis of a turbine flow field provides indicators of forcing function excitation frequencies (e.g., multiples of blade pass frequency) for turbine components. For the Pratt and Whitney Rocketdyne J-2X engine turbopumps, Campbell diagrams generated using these forcing function frequencies and the results of NASTRAN modal analyses show a number of components with modes in the engine operating range. As a consequence, forced response and static analyses are required for the prediction of combined stress, high cycle fatigue safety factors (HCFSF). Cyclically symmetric structural models have been used to analyze turbine vane and blade rows, not only in modal analyses, but also in forced response and static analyses. Due to the tortuous flow pattern in the turbine, dynamic pressure loading is not cyclically symmetric. Furthermore, CFD analyses predict dynamic pressure waves caused by adjacent and non-adjacent blade/vane rows upstream and downstream of the row analyzed. A MATLAB script has been written to calculate displacements due to the complex cyclically asymmetric dynamic pressure components predicted by CFD analysis, for all grids in a blade/vane row, at a chosen turbopump running speed. The MATLAB displacements are then read into NASTRAN, and dynamic stresses are calculated, including an adjustment for possible mistuning. In a cyclically symmetric NASTRAN static analysis, static stresses due to centrifugal, thermal, and pressure loading at the mode running speed are calculated. MATLAB is used to generate the HCFSF at each grid in the blade/vane row. When compared to an approach assuming cyclic symmetry in the dynamic flow field, the current approach provides better assurance that the worst case safety factor has been identified. An extended example for a J-2X turbopump component is provided.

Extended KN algebras and extended conformal field theories over higher genus Riemann surfaces

International Nuclear Information System (INIS)

Ceresole, A.; Huang Chaoshang

1990-01-01

A global operator formalism for extended conformal field theories over higher genus Riemann surfaces is introduced and extended KN algebra are obtained by means of the KN bases. The BBSS construction of the spin-3 operator is carried out for Kac-Moody algebra A 2 over a Riemann surface of arbitrary genus. (orig.)

7 CFR 1425.14 - Member business.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Member business. 1425.14 Section 1425.14 Agriculture... business. (a) At least 50 percent of a crop of an authorized commodity acquired by, or delivered to, a CMA... not be considered in determining the volume of member or nonmember business. ...

Ultra low injection angle fuel holes in a combustor fuel nozzle

Science.gov (United States)

York, William David

2012-10-23

A fuel nozzle for a combustor includes a mixing passage through which fluid is directed toward a combustion area and a plurality of swirler vanes disposed in the mixing passage. Each swirler vane of the plurality of swirler vanes includes at least one fuel hole through which fuel enters the mixing passage in an injection direction substantially parallel to an outer surface of the plurality of swirler vanes thereby decreasing a flameholding tendency of the fuel nozzle. A method of operating a fuel nozzle for a combustor includes flowing a fluid through a mixing passage past a plurality of swirler vanes and injecting a fuel into the mixing passage in an injection direction substantially parallel to an outer surface of the plurality of swirler vanes.

Nuclear reactor fuel element assemblies

International Nuclear Information System (INIS)

Krawiec, D.M.; Bevilacqua, F.

1974-01-01

The fuel elements of each fuel element group are separated from each other by means of a multitude of thin, intersecting plates in the from of grid strips. Flow deflectors near the surface of the fuel elements are used in order to make the coolant flow more turbulent. They are designed as vanes and arranged at a distance on the grid strips. Each deflector vane has two arms stretching in opposite directions, each one into a neighbouring channel. In outward direction, the deflector vanes are converging. The strips with the vanes can be put on the supporting grid of the fuel elements. The vane structure can be reinforced by providing distortions in the strip material near the vanes. (DG) [de

DUBNA: Member States

International Nuclear Information System (INIS)

Anon.

1992-01-01

The political upheaval in what was the Soviet Union was reflected in an Extraordinary Plenipotentiaries Committee of Joint Institute for Nuclear Research (JINR) Member States, held in Dubna, near Moscow, on 10-13 December, with representatives of eleven sovereign republics of the former Soviet State taking part

Youth Gang Members: Psychiatric Disorders and Substance Use

Directory of Open Access Journals (Sweden)

Albert John Sargent

2013-10-01

Full Text Available Objective: Approximately 260,000 of youth in the United States are gang-affiliated. There is a paucity of data available to identify the prevalence of mental health disorders in this population. Gang members share many of the features of “at risk” or juvenile justice involved youth who deny gang membership. The authors identified rates of psychiatric disorders within a juvenile justice population delineated in three categories: gang members, friends of gang members, and non-gang members. Methods: A retrospective review of records obtained by a juvenile probation department. A large detention center conducted mental health screenings on 7,615 youth aged 13–17. The mental health screenings were performed by either a master level or doctoral level mental health professional. Odds ratios were computed as an effect size for gender, race/ethnic differences, and gang-membership associations with self-reported psychiatric and substance use disorders. Logistic regression was used to evaluate the risk for psychiatric and substance use disorders among gang-members and friends of gang members. Diagnostic information was generated through a clinical interview and flexible battery. Results: Of the 7,615 youth in this study, ~50% had contact with gangs; 11% were self-identified gang-members, and 38% acknowledged having at least one friendship with a gang member. Similar to other studies, being male was a risk-factor for gang-membership (2.31 odds. In this multi-racial and ethnic study, Latinos had a greater affiliation with gang membership and association with gang members as friends (1.44 odds. Gang members were found to have increased rates of post-traumatic stress disorder (1.77 odds, current substance abuse (2.58 odds, oppositional defiant disorder, (1.24 odds and conduct disorder (4.05 odds; however, they were less likely to have an adjustment disorder than non-gang members (0.70 odds. Conclusions: Juveniles who received a mental health assessment

Range extender module. Enabler for electric mobility; Range-Extender-Modul. Wegbereiter fuer elektrische Mobilitaet

Energy Technology Data Exchange (ETDEWEB)

Fischer, Robert; Fraidl, Guenter Karl; Hubmann, Christian; Kapus, Paul Ernst; Kunzemann, Ralf; Sifferlinger, Bernhard; Beste, Frank [AVL List GmbH, Graz (Austria)

2009-10-15

The Range Extender as an auxiliary power supply for extended driving ranges is of significant importance in achieving a high level of customer acceptance for electric vehicles. The AVL concept is optimized for electric power generation in single-point operation and allows a compactly integrated, cost-efficient and weight-efficient module design. The internal combustion engine requirements of the Pure Range Extender from AVL permit not only the use of simplified four-stroke concepts but also the application of emission-optimized and fuel consumption-optimized two-stroke and rotary piston engines. (orig.)

Experimental Investigation of Turbine Vane Heat Transfer for Alternative Fuels

Energy Technology Data Exchange (ETDEWEB)

Nix, Andrew Carl [West Virginia Univ., Morgantown, WV (United States)

2015-03-23

The focus of this program was to experimentally investigate advanced gas turbine cooling schemes and the effects of and factors that contribute to surface deposition from particulate matter found in coal syngas exhaust flows on turbine airfoil heat transfer and film cooling, as well as to characterize surface roughness and determine the effects of surface deposition on turbine components. The program was a comprehensive, multi-disciplinary collaborative effort between aero-thermal and materials faculty researchers and the Department of Energy, National Energy Technology Laboratory (NETL). The primary technical objectives of the program were to evaluate the effects of combustion of syngas fuels on heat transfer to turbine vanes and blades in land-based power generation gas turbine engines. The primary questions to be answered by this investigation were; What are the factors that contribute to particulate deposition on film cooled gas turbine components? An experimental program was performed in a high-temperature and pressure combustion rig at the DOE NETL; What is the effect of coal syngas combustion and surface deposition on turbine airfoil film cooling? Deposition of particulate matter from the combustion gases can block film cooling holes, decreasing the flow of the film coolant and the film cooling effectiveness; How does surface deposition from coal syngas combustion affect turbine surface roughness? Increased surface roughness can increase aerodynamic losses and result in decreased turbine hot section efficiency, increasing engine fuel consumption to maintain desired power output. Convective heat transfer is also greatly affected by the surface roughness of the airfoil surface; Is there any significant effect of surface deposition or erosion on integrity of turbine airfoil thermal barrier coatings (TBC) and do surface deposits react with the TBC in any way to decrease its thermal insulating capability? Spallation and erosion of TBC is a persistent problem in

Challenges associated with extending spent fuel storage until reprocessing or disposal

International Nuclear Information System (INIS)

Carlsen, Brett; Saegusa, Toshiari; Wasinger, Karl; Grahn, Per; Wolff, Dietmar; Waters, Michael; Bevilacqua, Arturo

2014-01-01

Existing spent fuel storage (SFS) practices are the result of the past presumptions that an end point, e.g. sufficient reprocessing and/or disposal capacity, would be available within the short term (approximately 50 years). Consequently, long term storage (between approximately 50 and 100 years) considerations have not been included in planning the back end of the nuclear fuel cycle. The present reality shows that no country has yet neither licensed nor built nor operated a deep geological repository for spent fuel (SF) and/or high level waste (HLW). Further, present and projected SF generation rates - more than 10 000 metric tons of heavy metal (MTHM) a year - far exceed the current capacity for disposal - 0 MTHM - or reprocessing - 4 800 MTHM a year - and will continue to do so for the rest of this decade. As a result, the SFS periods will extend. Moreover, as the SFM end point - reprocessing and/or disposal - is not presently defined with certainty in most countries, SFS periods will extend over periods within or beyond the long term in those countries. The IAEA has started in October 2010 a programmatic activity to consider challenges associated with extending SFS durations. After four consultants meetings and two technical meetings, a need has been identified for a SFS framework based on renewable storage periods - with as many renewals as may be needed - to ensure safe and secure SFS until sufficient reprocessing and/or disposal capacity is implemented. Over the course of the technical meetings, the consultants have worked with delegates of 36 Member States and 2 International Organizations to emphasize the importance of establishing programs that can provide sufficient confidence that age-related degradation will be recognized and addressed to effectively prevent unacceptable consequences. This paper considers a number of topics from the perspective of assuring safe and effective SFS as storage periods extend including: SFS concepts, packaging of SF

ADA members weigh in on critical issues.

Science.gov (United States)

Burgess, Karen; Ruesch, Jon D; Mikkelsen, Matthew C; Wagner, Karen Schaid

2003-01-01

Science, new technology, patient care, dental reimbursement and government regulations all affect today's dental practitioners. To find out more about how such challenges may affect current private practitioners, the American Dental Association conducted the 2000 Membership Needs and Opinions Survey. A questionnaire was sent to 6,310 ADA members in January 2000 with follow-up mailings in February, March and April 2000. Data collection was completed in July 2000. The survey included questions on critical professional issues, and on perceptions of the ADA and ADA priorities. A total of 3,558 completed surveys were received for an adjusted response rate of 59.5 percent. Members rated the identified issues' level of importance to them. The top three issues included "maintaining my ability to recommend the treatment option I feel is most appropriate for my patients," "receiving fair reimbursement for the dental services I provide," and "protecting myself, my staff and my patients from communicable diseases." New dentists found other items to be more significant to them compared with members overall. Although ADA members as a whole had similar views on critical issues facing dentistry and ADA priorities, there were significant differences regarding some issues. New dentists were far more concerned about securing funds for their practice and paying off debt than were all ADA members. Minority dentists expressed greater levels of concern about certain issues than did all ADA members. When planning and implementing ADA activities, the Association should continue to take into account members' relative rankings of professional issues and note issues of special interest to selected membership subgroups.

A 3-Factor Model Relating Communication to Risk Mitigation of Extended Information System Failover

Directory of Open Access Journals (Sweden)

Athanasios Podaras

2015-06-01

Full Text Available This paper aims to analyse the relation between timely and effective communication and risk mitigation of late recovery after an unexpected information system outage in enterprises. An unforeseen information system failure in modern enterprise units, may result to significant operational and financial damage. In such a critical incident, effective communication between the team leaders and the recovery team involved, can minimize or even eliminate this negative impact. An extended information system outage can be perceived as a time deviation from the Maximum Accepted Outage (ΜΑΟ timeframe, proposed by the business continuity management, according to the value of which dependent business functions may be interrupted without any serious effects to the company. The paper examines the relation between 3 basic factors and the efficient communication between team members. The factors are: timely information distribution, staff availability and network availability. Through the current paper, the author proposes a risk analysis model, based on the Composite Risk Index theory of Risk Management, which can significantly diminish the possibility of an extended information system outage, as well as calculate the extended time required to recover a system when the aforementioned factors emerge in their worst form. The precise calculation of recovery time can be achieved via the execution of business continuity tests which include scenarios, according to which an unexpected system outage coexists with delayed information distribution as well as low staff and network availability.

Engine piston assembly and forged piston member therefor having a cooling recess

Energy Technology Data Exchange (ETDEWEB)

Cooper, B.C.; Erickson, K.L.; Green, J.A.; Nyez, D.S.

1989-09-19

This patent describes a forged steel piston member for reciprocating movement in an engine. It comprises: an upper portion of substantially cylindrical shape and having a central axis, a top surface, a tubular wall depending from the top surface and having a peripheral groove adapted to receive a sealing ring, a lower end surface, and an inwardly facing wall surface extending upwardly from the lower end surface. The upper portion further includes an outwardly facing wall surface spaced radially inwardly from the inwardly facing wall surface and a downwardly facing transition portion blendingly associated with the inwardly and outwardly facing wall surfaces to collectively define an annular cooling recess, the transition portion being elevational spaced a relatively short distance from the top surface; and the inwardly facing wall surface being a machined surface of revolution about the central axis integral or one-piece forging.

Viability of bull semen extended with commercial semen extender ...

African Journals Online (AJOL)

Andrea Raseona

stored at 24 °C. Sperm motility parameters, morphology, and viability were analysed ... body size, slow average daily weight gain, decreased fertility, extended .... were determined by counting a total of 200 spermatozoa per each stained slide.

Cracking in Flexural Reinforced Concrete Members

DEFF Research Database (Denmark)

Rasmussen, Annette Beedholm; Fisker, Jakob; Hagsten, Lars German

2017-01-01

The system of cracks developing in reinforced concrete is in many aspects essential when modelling structures in both serviceability- and ultimate limit state. This paper discusses the behavior concerning crack development in flexural members observed from tests and associates it with two different...... existing models. From the investigations an approach is proposed on how to predict the crack pattern in flexural members involving two different crack systems; primary flexural cracks and local secondary cracks. The results of the approach is in overall good agreement with the observed tests and captures...... the pronounced size effect associated with flexural cracking in which the crack spacing and crack widths are approximately proportional to the depth of the member....

E-Commerce in OIC members: Facts - Challenges - Prospects

OpenAIRE

Al-Abdali, Abid

2005-01-01

The study seeks to explore the importance of E-Commerce and ICT and their impact on economies of OIC members. Challenges and obstacles of E-Commerce application in member states are analyzed and discussed. The study has concluded that E-Commerce has become an important application in most member states. It also showed that despite there has been growth in the application of E-Commerce in some countries, but in general OIC members as a whole are still behind in the track compared to other grou...

M dwarfs from the Einstein extended medium sensitivity survey

International Nuclear Information System (INIS)

Fleming, T.A.; Liebert, J.; Gioia, I.M.; Maccacaro, T.

1988-01-01

A complete sample of X-ray selected M dwarfs are presented which were serendipitously detected in the extended Einstein Observatory Medium Sensitivity Survey (MSS). The MSS detected only early M dwarfs (type MO through M5), 84 percent of which were emission stars (i.e., type Me V). It was calculated that the X-ray luminosity function for early M dwarfs with a log Lx greater than 27.6 and, by comparison to optical luminosity functions, find that about 25 percent of all early M dwarfs emit X-rays at a level greater than log Lx = 27.6. This result is compared to luminosity function estimates from optically selected samples and discussed in light of the sample's kinematic and mean age. Also presented is H alpha and Ca II K line fluxes for each member of the sample and it is shown that the surface H alpha and Ca II K luminosities do indeed correlate with Lx. The significance of this effect to theories of chromospheric and coronal heating is explained. 76 references

Evolution properties of the community members for dynamic networks

Science.gov (United States)

Yang, Kai; Guo, Qiang; Li, Sheng-Nan; Han, Jing-Ti; Liu, Jian-Guo

2017-03-01

The collective behaviors of community members for dynamic social networks are significant for understanding evolution features of communities. In this Letter, we empirically investigate the evolution properties of the new community members for dynamic networks. Firstly, we separate data sets into different slices, and analyze the statistical properties of new members as well as communities they joined in for these data sets. Then we introduce a parameter φ to describe community evolution between different slices and investigate the dynamic community properties of the new community members. The empirical analyses for the Facebook, APS, Enron and Wiki data sets indicate that both the number of new members and joint communities increase, the ratio declines rapidly and then becomes stable over time, and most of the new members will join in the small size communities that is s ≤ 10. Furthermore, the proportion of new members in existed communities decreases firstly and then becomes stable and relatively small for these data sets. Our work may be helpful for deeply understanding the evolution properties of community members for social networks.

Mental Wellbeing of Family Members of Autistic Adults

Science.gov (United States)

Herrema, Renske; Garland, Deborah; Osborne, Malcolm; Freeston, Mark; Honey, Emma; Rodgers, Jacqui

2017-01-01

Family members are often the primary caregiver for autistic adults and this responsibility may impact on the carer's wellbeing and quality of life. 109 family members of autistic adults completed an online survey assessing their wellbeing relating to their caring role for their autistic relative. Family members who were supporting an autistic…

The Agency's Safeguards System (1965, as provisionally extended in 1966 and 1968); Sistema de Salvaguardias del Organismo (1965, ampliado provisionalmente en 1966 y 1968)

Energy Technology Data Exchange (ETDEWEB)

NONE

1968-09-24

The Agency's safeguards system, as approved by the Board of Governors in 1965, and provisionally extended in 1966, is set forth in this document for the Information of all Members [Spanish] En el presente documento se reproduce, para informacion de todos los Estados Miembros, el Sistema de salvaguardias del Organismo aprobado por la Junta de Gobernadores en 1965 y ampliado provisionalmente en 1966 y 1968.

48 CFR 6301.2 - Qualifications of members.

Science.gov (United States)

2010-10-01

... contract law. ... CONTRACT APPEALS BOARD OF CONTRACT APPEALS 6301.2 Qualifications of members. Each member of the Board must... administrative law judges appointed pursuant to section 3105 of title 5 of the United States Code, with the...

[Comment on] BOSP members

Science.gov (United States)

Richman, Barbara T.

The new Board on Ocean Science and Policy (BOSP) (Eos, June 7, 1983, p. 402) met for the first time on May 4. John B. Slaughter, former director of the National Science Foundation and now chancellor of the University of Maryland in College Park, is the board's chairman. Other board members are D. James Baker, Jr. (University of Washington, Seattle); Kirk Bryan (Geophysical Fluid Dynamics Laboratory, Princeton University); John P. Craven (University of Hawaii); Charles L. Drake (Dartmouth College); Paul M. Fye (Woods Hole Oceanographic Institution); Edward D. Goldberg (Scripps Institution of Oceanography); G. Ross Heath (Oregon State University); Judith T. Kildow (Massachusetts Institute of Technology); John A. Knauss (University of Rhode Island); James J. McCarthy (Museum of Comparative Zoology, Harvard University); H. William Menard (Scripps Institution of Oceanography); C. Barry Raleigh (Lamont-Doherty Geological Observatory); Roger Revelle (University of California, San Diego); David A. Ross (Woods Hole Oceanographic Institution); Brian J. Rothschild (University of Maryland); William M. Sackett (University of South Florida); John H. Steele (Woods Hole Oceanographic Institution); and Carl Wunsch (MIT). Wallace Broecker (Lamont-Doherty Geological Observatory), an original board member, resigned after the first meeting. Broecker told Eos that combining the science and policy boards resulted in a new board whose mission is too broad. A new board member will be appointed in Broecker's place

The dialogically extended mind

DEFF Research Database (Denmark)

Fusaroli, Riccardo; Gangopadhyay, Nivedita; Tylén, Kristian

2014-01-01

A growing conceptual and empirical literature is advancing the idea that language extends our cognitive skills. One of the most influential positions holds that language – qua material symbols – facilitates individual thought processes by virtue of its material properties. Extending upon this model...... relate our approach to other ideas about collective minds and review a number of empirical studies to identify the mechanisms enabling the constitution of interpersonal cognitive systems....

Quasi-extended asymptotic functions

International Nuclear Information System (INIS)

Todorov, T.D.

1979-01-01

The class F of ''quasi-extended asymptotic functions'' is introduced. It contains all extended asymptotic functions as well as some new asymptotic functions very similar to the Schwartz distributions. On the other hand, every two quasiextended asymptotic functions can be multiplied as opposed to the Schwartz distributions; in particular, the square delta 2 of an asymptotic function delta similar to Dirac's delta-function, is constructed as an example

Scientific collaboration between 'old' and 'new' member states

DEFF Research Database (Denmark)

Makkonen, Teemu; Mitze, Timo Friedel

2016-01-01

following the two enlargement waves 2004 and 2007 has significantly increased the co-publication intensity of the new member states with other member countries. The empirical results based on data collected from the Web of Science database and Difference-in-Difference estimations point towards a conclusion...... that joining the EU indeed has had an additional positive impact on the co-publication intensity between the new and old member states and, in particular, between the new member states themselves. These results give tentative support for the successfulness of the EU’s science policies in achieving a common...

Vortex Generators in a Streamline-Traced, External-Compression Supersonic Inlet

Science.gov (United States)

Baydar, Ezgihan; Lu, Frank K.; Slater, John W.; Trefny, Charles J.

2017-01-01

Vortex generators within a streamline-traced, external-compression supersonic inlet for Mach 1.66 were investigated to determine their ability to increase total pressure recovery and reduce total pressure distortion. The vortex generators studied were rectangular vanes arranged in counter-rotating and co-rotating arrays. The vane geometric factors of interest included height, length, spacing, angle-of-incidence, and positions upstream and downstream of the inlet terminal shock. The flow through the inlet was simulated numerically through the solution of the steady-state, Reynolds-averaged Navier-Stokes equations on multi-block, structured grids using the Wind-US flow solver. The vanes were simulated using a vortex generator model. The inlet performance was characterized by the inlet total pressure recovery and the radial and circumferential total pressure distortion indices at the engine face. Design of experiments and statistical analysis methods were applied to quantify the effect of the geometric factors of the vanes and search for optimal vane arrays. Co-rotating vane arrays with negative angles-of-incidence positioned on the supersonic diffuser were effective in sweeping low-momentum flow from the top toward the sides of the subsonic diffuser. This distributed the low-momentum flow more evenly about the circumference of the subsonic diffuser and reduced distortion. Co-rotating vane arrays with negative angles-of-incidence or counter-rotating vane arrays positioned downstream of the terminal shock were effective in mixing higher-momentum flow with lower-momentum flow to increase recovery and decrease distortion. A strategy of combining a co-rotating vane array on the supersonic diffuser with a counter-rotating vane array on the subsonic diffuser was effective in increasing recovery and reducing distortion.

EAES: Extended Advanced Encryption Standard with Extended Security

Directory of Open Access Journals (Sweden)

Abul Kalam Azad

2018-05-01

Full Text Available Though AES is the highest secure symmetric cipher at present, many attacks are now effective against AES too which is seen from the review of recent attacks of AES. This paper describes an extended AES algorithm with key sizes of 256, 384 and 512 bits with round numbers of 10, 12 and 14 respectively. Data block length is 128 bits, same as AES. But unlike AES each round of encryption and decryption of this proposed algorithm consists of five stages except the last one which consists of four stages. Unlike AES, this algorithm uses two different key expansion algorithms with two different round constants that ensure higher security than AES. Basically, this algorithm takes one cipher key and divides the selected key of two separate sub-keys: FirstKey and SecondKey. Then expand them through two different key expansion schedules. Performance analysis shows that the proposed extended AES algorithm takes almost same amount of time to encrypt and decrypt the same amount of data as AES but with higher security than AES.

Research of performance prediction to energy on hydraulic turbine

International Nuclear Information System (INIS)

Quan, H; Li, R N; Li, Q F; Han, W; Su, Q M

2012-01-01

Refer to the low specific speed Francis turbine blade design principle and double-suction pump structure. Then, design a horizontal double-channel hydraulic turbine Francis. Through adding different guide vane airfoil and and no guide vane airfoil on the hydraulic conductivity components to predict hydraulic turbine energy and using Fluent software to numerical simulation that the operating conditions and point. The results show that the blade pressure surface and suction surface pressure is low when the hydraulic turbine installation is added standard positive curvature of the guide vane and modified positive curvature of guide vane. Therefore, the efficiency of energy recovery is low. However, the pressure of negative curvature guide vane and symmetric guide vane added on hydraulic turbine installations is larger than that of the former ones, and it is conducive to working of runner. With the decreasing of guide vane opening, increasing of inlet angle, flow state gets significantly worse. Then, others obvious phenomena are that the reflux and horizontal flow appeared in blade pressure surface. At the same time, the vortex was formed in Leaf Road, leading to the loss of energy. Through analyzing the distribution of pressure, velocity, flow lines of over-current flow in the the back hydraulic conductivity components in above programs we can known that the hydraulic turbine installation added guide vane is more reasonable than without guide vanes, it is conducive to improve efficiency of energy conversion.

Prevalence, Knowledge and Attitudes Towards Smoking Among SEPAR Members.

Science.gov (United States)

Solano Reina, Segismundo; Jiménez Ruiz, Carlos A; de Higes Martinez, Eva; Garcia Rueda, Marcos; Callejas González, Francisco J; de Granda Orive, Jose I; Vaquero Lozano, Paz; de Lucas Ramos, Pilar; Alfageme Michavila, Inmaculada

2016-12-01

The aims of this study were to estimate the prevalence of smoking among SEPAR members, and their approach to smoking cessation in their patients. An online survey was completed by 640 members (496 pulmonologists, 45 nurses, 34 thoracic surgeons, 37 physiotherapists, and 28 other specialists). Of the members interviewed, 5% confessed that they were smokers: 3.5% pulmonologists; 8.9% nurses; 8.8% thoracic surgeons, and 13.5% physiotherapists. A total of 96% of members assign a lot or quite a lot of importance to setting an example; 98% of members always or often ask their patients about their smoking habit. The most effective anti-smoking intervention, according to 77% of members, is a combination of drugs and psychological support. These results are an indicator of the awareness and commitment of SEPAR members to smoking and its cessation. Copyright © 2016 SEPAR. Publicado por Elsevier España, S.L.U. All rights reserved.

Study of High Efficiency Flow Regulation of VIGV in Centrifugal Compressor

Directory of Open Access Journals (Sweden)

Chunjun Ji

2016-01-01

Full Text Available Variable inlet guide vane (VIGV is used to control the mass flow and generate prewhirl in centrifugal compressors. Due to the tip clearance of the guide vanes and the defect of the traditional guide vane profiles, the mass flow regulation of VIGV is limited, resulting in a large waste of compressed gas. Two kinds of inlet flow channels were proposed to eliminate the influence of tip clearance. These structures were numerically investigated at different setting angles. The results show that the improved channels not only expand the range of mass flow regulation, but also reduce the power and increase the efficiency of the compressor. Ten kinds of guide vane profiles, including different thickness distribution, camber line profile, were selected to compare with the original one and with each other. In the premise of ensuring the performance of compressor, the best guide vane profile was selected. The results show that reducing the guide vane thickness, increasing the guide vane camber angle, and increasing the distance between the maximum camber position and the leading edge of guide vane can help expand the range of mass flow regulation. The achievement of this research can effectively improve the flow regulation ability of VIGV and the performance of compressor.

19 CFR 122.49b - Electronic manifest requirement for crew members and non-crew members onboard commercial aircraft...

Science.gov (United States)

2010-04-01

...” means air carrier employees and their family members and persons traveling onboard a commercial aircraft...), air carrier employees, their family members, and persons onboard for the safety of the flight are...) Date of birth; (iii) Place of birth (city, state—if applicable, country); (iv) Gender (F = female; M...

Extending cosmology: the metric approach

OpenAIRE

Mendoza, S.

2012-01-01

Comment: 2012, Extending Cosmology: The Metric Approach, Open Questions in Cosmology; Review article for an Intech "Open questions in cosmology" book chapter (19 pages, 3 figures). Available from: http://www.intechopen.com/books/open-questions-in-cosmology/extending-cosmology-the-metric-approach

Extended cognition and epistemic luck

NARCIS (Netherlands)

Carter, J.A.

2013-01-01

When extended cognition is extended into mainstream epistemology, an awkward tension arises when considering cases of environmental epistemic luck. Surprisingly, it is not at all clear how the mainstream verdict that agents lack knowledge in cases of environmental luck can be reconciled with

Glued structural members

Science.gov (United States)

Russell C. Moody; Jen Y. Liu

1999-01-01

Glued structural members are manufactured in a variety of configurations. Structural composite lumber (SCL) products consist of small pieces of wood glued together into sizes common for solid-sawn lumber. Glued-laminated timber (glulam) is an engineered stress-rated product that consists of two or more layers of lumber in which the grain of all layers is oriented...

Extending Mondrian Memory Protection

Science.gov (United States)

2010-11-01

a kernel semaphore is locked or unlocked. In addition, we extended the system call interface to receive notifications about user-land locking...operations (such as calls to the mutex and semaphore code provided by the C library). By patching the dynamically loadable GLibC5, we are able to test... semaphores , and spinlocks. RTO-MP-IST-091 10- 9 Extending Mondrian Memory Protection to loading extension plugins. This prevents any untrusted code

Extended Cognitive System and Epistemic Subject

Directory of Open Access Journals (Sweden)

Trybulec Barbara

2015-03-01

Full Text Available The concept of an extended cognitive system is central to contemporary studies of cognition. In the paper I analyze the place of the epistemic subject within the extended cognitive system. Is it extended as well? In answering this question I focus on the differences between the first and the second wave of arguments for the extended mind thesis. I argue that the position of Cognitive Integration represented by Richard Menary is much more intuitive and fruitful in analyses of cognition and knowledge than the early argument formulated by Andy Clark and David Chalmers. Cognitive Integration is compatible with virtue epistemology of John Greco’s agent reliabilism. The epistemic subject is constituted by its cognitive character composed of an integrated set of cognitive abilities and processes. Some of these processes are extended, they are a manipulation of external informational structures and, as such, they constitute epistemic practices. Epistemic practices are normative; to conduct them correctly the epistemic subject needs to obey epistemic norms embedded in the cultural context. The epistemic subject is not extended because of the casual coupling with external informational artifacts which extend his mind from inside the head and into the world. Rather, cognitive practices constitute the subject’s mind, they transform his cognitive abilities, and this is what makes the mind and epistemic subject “extended”.

Extended asymptotic functions - some examples

International Nuclear Information System (INIS)

Todorov, T.D.

1981-01-01

Several examples of extended asymptotic functions of two variables are given. This type of asymptotic functions has been introduced as an extension of continuous ordinary functions. The presented examples are realizations of some Schwartz distributions delta(x), THETA(x), P(1/xsup(n)) and can be multiplied in the class of the asymptotic functions as opposed to the theory of Schwartz distributions. The examples illustrate the method of construction of extended asymptotic functions similar to the distributions. The set formed by the extended asymptotic functions is also considered. It is shown, that this set is not closed with respect to addition and multiplication

On the Cλ-extended w∞-symmetry

International Nuclear Information System (INIS)

Douari, J.; El Kinani, E.H.

2003-08-01

Starting from the C λ -extended oscillator algebras, we obtain a new deformed w ∞ -algebra. More precisely, we show that the C λ -extended w ∞ -algebra generators may be expressed via the annihilation and creation operators of the C λ -extended oscillator algebras a and a † as an infinite-dimensional extension of the realization of sp(2) algebra. (author)

Extended recency effect extended: blocking, presentation mode, and retention interval.

Science.gov (United States)

Glidden, L M; Pawelski, C; Mar, H; Zigman, W

1979-07-01

The effect of blocking of stimulus items on the free recall of EMR adolescents was examined. In Experiment 1 a multitrial free-recall list of 15 pictures was presented either simultaneously in groups of 3, or sequentially, one at a time. Consistent ordering was used in both conditions, so that on each trial, each item in each set of 3 pictures was presented contiguously with the other 2 items from that set. In addition, recall came immediately or after a filled or unfilled delay of 24.5 seconds. Results showed that simultaneous presentation led to higher recall, subjective organization, and clustering than did sequential presentation, but analysis of serial-position curves showed a much reduced extended recency effect in comparison with previous studies. Experiment 2 was designed to determine whether the cause of the reduced extended recency was the use of pictures rather than words as stimuli. Stimuli were presented either as pictures, as pictures with auditory labels, or as words with auditory labels, with both simultaneous and consistent ordering for all conditions. Results indicated a strong extended recency effect for all groups, eliminating presentation mode as a causal factor in the data of Experiment 1. We concluded that blocking leads to increased organization and recall over a variety of presentation modes, rates, and block sizes.

Bacteriospermia in extended porcine semen.

Science.gov (United States)

Althouse, Gary C; Lu, Kristina G

2005-01-15

Bacteriospermia is a frequent finding in freshly extended porcine semen and can result in detrimental effects on semen quality and longevity if left uncontrolled. The primary source of bacterial contamination is the boar. Other sources that have been identified include environment, personnel, and the water used for extender preparation. A 1-year retrospective study was performed on submissions of extended porcine semen for routine quality control bacteriological screening at the University of Pennsylvania. Out of 250 sample submissions, 78 (31.2%) tested positive for bacterial contamination. The most popular contaminants included Enterococcus spp. (20.5%), Stenotrophomonas maltophilia (15.4%), Alcaligenes xylosoxidans (10.3%), Serratia marcescens (10.3%), Acinetobacter lwoffi (7.7%), Escherichia coli (6.4%), Pseudomonas spp. (6.4%), and others (23.0%). Prudent individual hygiene, good overall sanitation, and regular monitoring can contribute greatly in controlling bacterial load. Strategies that incorporate temperature-dependent bacterial growth and hyperthermic augmentation of antimicrobial activity are valuable for effective control of susceptible bacterial loads. Aminoglycosides remain the most popular antimicrobial class used in porcine semen extenders, with beta-lactam and lincosamide use increasing. With the advent of more novel antimicrobial selection and semen extender compositions in swine, prudent application and understanding of in vitro pharmacodynamics are becoming paramount to industry success in the use of this breeding modality.

STUDY ON COMMUNICATION TEAM’S MEMBERS ROLES

Directory of Open Access Journals (Sweden)

Cristina BORCA

2014-06-01

Full Text Available The implementation of the management strategy for increasing the competitiveness of modern organizations is more effective if it is correlated with the organizational communication strategy. Team communication of an organization must be an agile one, its agility depending decisively on the way it was constituted, the assigned role for each team member, the statuses etc. A valuation of all skills and abilities of each member of the communication team is therefore required to harmonize and integrate the team into the overall structure of the company. The objective of the paper is to identify the extent to which the formal role of each team member is the same (almost the same with the role determined by applying the Belbin test. The results of the research are prerequisites for development of measures for individual professional development and integration /reintegration of team members in order to increase agility.

Materials Delivered by Member States

International Nuclear Information System (INIS)

1966-01-01

The information given in this document is divided into two parts. In part I the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 31 December 1965 in compliance with requests the Agency had made under Article IX. D. Part III contains information about materials which had not been delivered by 31 December but which had been allocated, in accordance with Article XI. F. 1 of the Statute, to approved Agency projects for which project arrangements were in force on that date

Materials Delivered by Member States

International Nuclear Information System (INIS)

1965-01-01

The information given in this document is divided into two parts. In part I the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 31 December 1964 in compliance with requests the Agency had made under Article IX. D. Part II contains information about materials which had not been delivered by 31 December but which had been allocated, in accordance with Article XI. F. 1 of the Statute, to approved Agency projects for which project arrangements were in force on that date

Materials Delivered by Member States

International Nuclear Information System (INIS)

1968-01-01

The information given in this document is divided into two parts. In part I the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 30 June 1968 in compliance with requests the Agency had made under Article IX,D. Part II contains information about materials which had not been delivered by 30 June 1968 but which had been allocated, in accordance with Article XI.F.I of the Statute, to approved Agency projects for which project arrangements were in force on that date

The Foreign Policies of European Union Member States

DEFF Research Database (Denmark)

Foreign Policies of EU Member States provides a clear and current overview of the motivations and outcomes of EU Member States regarding their foreign policy-making within and beyond the EU. It provides an in-depth analysis of intra-EU policy-making and sheds light, in an innovative and understan......Foreign Policies of EU Member States provides a clear and current overview of the motivations and outcomes of EU Member States regarding their foreign policy-making within and beyond the EU. It provides an in-depth analysis of intra-EU policy-making and sheds light, in an innovative...... prerogative exercised by all EU Member States is to construct their own foreign policies on everything from trade and defence with the rest of the world. This combination of clarity, thematic structure and empirical case studies make this an ideal textbook for all upper-level students of European foreign...

Extended quantum mechanics

International Nuclear Information System (INIS)

Pavel Bona

2000-01-01

The work can be considered as an essay on mathematical and conceptual structure of nonrelativistic quantum mechanics which is related here to some other (more general, but also to more special and 'approximative') theories. Quantum mechanics is here primarily reformulated in an equivalent form of a Poisson system on the phase space consisting of density matrices, where the 'observables', as well as 'symmetry generators' are represented by a specific type of real valued (densely defined) functions, namely the usual quantum expectations of corresponding selfjoint operators. It is shown in this paper that inclusion of additional ('nonlinear') symmetry generators (i. e. 'Hamiltonians') into this reformulation of (linear) quantum mechanics leads to a considerable extension of the theory: two kinds of quantum 'mixed states' should be distinguished, and operator - valued functions of density matrices should be used in the role of 'nonlinear observables'. A general framework for physical theories is obtained in this way: By different choices of the sets of 'nonlinear observables' we obtain, as special cases, e.g. classical mechanics on homogeneous spaces of kinematical symmetry groups, standard (linear) quantum mechanics, or nonlinear extensions of quantum mechanics; also various 'quasiclassical approximations' to quantum mechanics are all sub theories of the presented extension of quantum mechanics - a version of the extended quantum mechanics. A general interpretation scheme of extended quantum mechanics extending the usual statistical interpretation of quantum mechanics is also proposed. Eventually, extended quantum mechanics is shown to be (included into) a C * -algebraic (hence linear) quantum theory. Mathematical formulation of these theories is presented. The presentation includes an analysis of problems connected with differentiation on infinite-dimensional manifolds, as well as a solution of some problems connected with the work with only densely defined unbounded

5 CFR 842.209 - Members of Congress.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Members of Congress. 842.209 Section 842.209 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT (CONTINUED) CIVIL SERVICE REGULATIONS (CONTINUED) FEDERAL EMPLOYEES RETIREMENT SYSTEM-BASIC ANNUITY Eligibility § 842.209 Members of Congress. (a...

Extended Life Coolant Testing

Science.gov (United States)

2016-06-06

number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1. REPORT DATE (DD-MM-YYYY) 06-06-2016 2. REPORT TYPE Interim Report 3. DATES COVERED ... Corrosion Testing of Traditional and Extended Life Coolants 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Hansen, Gregory A. T...providing vehicle specific coolants. Several laboratory corrosion tests were performed according to ASTM D1384 and D2570, but with a 2.5x extended time

Why 4-H Members Leave: A Study of Discontinuance through Both Current 4-H Members and Former Members

Science.gov (United States)

Chilek, Kevin Dwayne

2012-01-01

4-H members quit. It is part of every 4-H program, and according to the research, it is even part of growing up. If only we knew why they quit, we could possibly do something about it. To date, the reasons youth join 4-H have been more thoroughly researched than the reasons they quit. This study explores why youth choose to discontinue membership…

19 CFR 122.49c - Master crew member list and master non-crew member list requirement for commercial aircraft...

Science.gov (United States)

2010-04-01

..., DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Aircraft Entry and Entry Documents; Electronic Manifest Requirements for Passengers, Crew Members, and Non-Crew Members Onboard... sections, must electronically transmit to Customs and Border Protection (CBP), by means of an electronic...

When care situations evoke difficult emotions in nursing staff members: an ethnographic study in two Norwegian nursing homes.

Science.gov (United States)

Sandvoll, Anne Marie; Grov, Ellen Karine; Kristoffersen, Kjell; Hauge, Solveig

2015-01-01

Caring practice in nursing homes is a complex topic, especially the challenges of meeting the basic needs of residents when their behaviour evokes difficult emotions. Cognitive and physical changes related to aging and disability can contribute to behaviours considered to be unacceptable. For example, resident behaviours such as spitting, making a mess with food or grinding teeth are behaviours that most people do not want to see, hear or experience. The aim of this study was to gain a deeper understanding of how nursing home staff members deal with such behaviours in care situations. This article draws on ethnographic data to describe how nursing home staff members manage unpleasant resident behaviours. The study was based on two long-term units in two Norwegian public nursing homes. The Region's Medical Ethics Committee and the Norwegian Social Science Data Services granted approval. In total, 45 participants (37 nursing aides and eight nurses) agreed to participate in this study. Ten of the participants were interviewed at the end of the field study. This study indicates that nursing home staff members experience difficult emotions related to some residents' behaviours. However, they found these feelings difficult to express and rarely verbalized them openly. In addition, they were characterized by a strong obligation to help all residents, despite their own feelings. Therefore, it appears that an inner struggle occurs as a part of everyday practice. Despite these difficult emotions, nursing staff members believed that they needed to manage their responses and continued to offer good care to all residents. These findings extend our understanding of this unarticulated part of nursing home practice.

CE: Military Sexual Trauma in Male Service Members.

Science.gov (United States)

Eckerlin, Denise M; Kovalesky, Andrea; Jakupcak, Matthew

2016-09-01

: The experience of military sexual trauma (MST), which can result from assault, battery, or harassment of a sexual nature, may jeopardize the mental health of service members as well as that of their family members, colleagues, and community members. Although a greater proportion of female than male service members are subjected to MST, the Department of Defense estimates that the absolute numbers of affected men and women, across all ranks and branches of military service, are nearly equal because roughly 85% of military members are men. Little research has explored the effects of MST on men. This article discusses the unique ways in which men may experience MST, and examines how social stereotypes of masculinity, myths surrounding sexual assault, and military culture and structure often influence a man's interpretation of an attack and his likelihood of reporting the incident or seeking treatment. It describes current treatments for MST-related mental health conditions and addresses implications for nurses and other health care professionals.

STRUCTURAL PERFORMANCE OF DEGRADED REINFORCED CONCRETE MEMBERS

International Nuclear Information System (INIS)

Braverman, J.I.; Miller, C.A.; Ellingwood, B.R.; Naus, D.J.; Hofmayer, C.H.; Bezler, P.; Chang, T.Y.

2001-01-01

This paper describes the results of a study to evaluate, in probabilistic terms, the effects of age-related degradation on the structural performance of reinforced concrete members at nuclear power plants. The paper focuses on degradation of reinforced concrete flexural members and shear walls due to the loss of steel reinforcing area and loss of concrete area (cracking/spalling). Loss of steel area is typically caused by corrosion while cracking and spalling can be caused by corrosion of reinforcing steel, freeze-thaw, or aggressive chemical attack. Structural performance in the presence of uncertainties is depicted by a fragility (or conditional probability of failure). The effects of degradation on the fragility of reinforced concrete members are calculated to assess the potential significance of various levels of degradation. The fragility modeling procedures applied to degraded concrete members can be used to assess the effects of degradation on plant risk and can lead to the development of probability-based degradation acceptance limits

Cosmological dynamics of extended chameleons

International Nuclear Information System (INIS)

Tamanini, Nicola; Wright, Matthew

2016-01-01

We investigate the cosmological dynamics of the recently proposed extended chameleon models at both background and linear perturbation levels. Dynamical systems techniques are employed to fully characterize the evolution of the universe at the largest distances, while structure formation is analysed at sub-horizon scales within the quasi-static approximation. The late time dynamical transition from dark matter to dark energy domination can be well described by almost all extended chameleon models considered, with no deviations from ΛCDM results at both background and perturbation levels. The results obtained in this work confirm the cosmological viability of extended chameleons as alternative dark energy models.

Cosmological dynamics of extended chameleons

Energy Technology Data Exchange (ETDEWEB)

Tamanini, Nicola [Institut de Physique Théorique, CEA-Saclay, CNRS UMR 3681, Université Paris-Saclay, F-91191 Gif-sur-Yvette (France); Wright, Matthew, E-mail: nicola.tamanini@cea.fr, E-mail: matthew.wright.13@ucl.ac.uk [Department of Mathematics, University College London, Gower Street, London, WC1E 6BT (United Kingdom)

2016-04-01

We investigate the cosmological dynamics of the recently proposed extended chameleon models at both background and linear perturbation levels. Dynamical systems techniques are employed to fully characterize the evolution of the universe at the largest distances, while structure formation is analysed at sub-horizon scales within the quasi-static approximation. The late time dynamical transition from dark matter to dark energy domination can be well described by almost all extended chameleon models considered, with no deviations from ΛCDM results at both background and perturbation levels. The results obtained in this work confirm the cosmological viability of extended chameleons as alternative dark energy models.

Functional genomic analysis supports conservation of function among cellulose synthase-like a gene family members and suggests diverse roles of mannans in plants

DEFF Research Database (Denmark)

Liepman, Aaron H; Nairn, C Joseph; Willats, William G T

2007-01-01

from Arabidopsis (Arabidopsis thaliana), guar (Cyamopsis tetragonolobus), and Populus trichocarpa catalyze beta-1,4-mannan and glucomannan synthase reactions in vitro. Mannan polysaccharides and homologs of CslA genes appear to be present in all lineages of land plants analyzed to date. In many plants......, the CslA genes are members of extended multigene families; however, it is not known whether all CslA proteins are glucomannan synthases. CslA proteins from diverse land plant species, including representatives of the mono- and dicotyledonous angiosperms, gymnosperms, and bryophytes, were produced...... they are prevalent at cell junctions and in buds. Taken together, these results demonstrate that members of the CslA gene family from diverse plant species encode glucomannan synthases and support the hypothesis that mannans function in metabolic networks devoted to other cellular processes in addition to cell wall...

Mental Wellbeing of Family Members of Autistic Adults.

Science.gov (United States)

Herrema, Renske; Garland, Deborah; Osborne, Malcolm; Freeston, Mark; Honey, Emma; Rodgers, Jacqui

2017-11-01

Family members are often the primary caregiver for autistic adults and this responsibility may impact on the carer's wellbeing and quality of life. 109 family members of autistic adults completed an online survey assessing their wellbeing relating to their caring role for their autistic relative. Family members who were supporting an autistic relative with co-occurring mental health difficulties and who they reported as unprepared for the future, self-reported higher levels of worry, depression, anxiety and stress, and poorer quality of life. These findings emphasise the importance of support for family members of autistic adults, whether through external services to support their relative or individual mental health support for the carer.

The relationship between mental health workers and family members

NARCIS (Netherlands)

van de Bovenkamp, H.M.; Trappenburg, M.J.

2010-01-01

Objective To study the relationship between family members and mental health care workers to learn more about the support available to family members of mental health patients. Methods Eighteen interviews were conducted with family members, seven with professionals and two with patients.

Experimental investigation of hinged and spring loaded rolling piston compressors pertaining to a turbo rotary engine

International Nuclear Information System (INIS)

Okur, Melih; Akmandor, Ibrahim Sinan

2011-01-01

Hinged rolling piston compressor of a new thermodynamic cycle Pars engine promises high performance figures such as single stage high compression levels and higher volume flow discharge with competitively low input power and torque. The pumping characteristic of the present engine compressor unit has been increased by the implementation of a spring less vane configuration. The reciprocating vane which is usually operated by spring compression in air conditioning and refrigeration unit has been replaced by a hinge vane mechanism. At high speeds, the conventional spring loaded vane which is forced against the eccentrically moving rotor periphery does disconnect and starts rocking. With the new configuration, this mishap has been eliminated and subsequently resulting compressor pressure leaks have been avoided. Compressor experiments have been carried out at predetermined rotor speeds and compressed volume flow amounts and required shaft powers have been measured and derived accordingly. Experimentally determined pressure-volume relations have been compared with isentropic, isothermal, isochoric compressions as well as isobaric process. It is seen that at lower speeds, hinged vane compression is half way between isentropic and isochoric compressions whereas at high speed the compression process approaches further isochoric compression behavior. The isentropic compression efficiency of the hinged vane compressor is around 85% for pressures reaching 9 atm. - Research highlights: → Volume flow rate of rotary vane compressor unit has been increased by a hinged vane mechanism. → Hinged compressor pressure output is almost twice the performance of a spring loaded compressor. → The slipping and rocking of the spring loaded vane against the rolling piston have been eliminated.

Nurse IOM members' contributions to the Institute of Medicine.

Science.gov (United States)

Grey, Margaret; Holzemer, William L; Larson, Elaine

2012-01-01

Nursing is the largest health care profession, and Institute of Medicine (IOM) nurse members have the potential to contribute to health policy through IOM activities. We studied reported activities of IOM nurse members. To describe activities of IOM nurse members within the IOM. An e-mail survey was conducted that asked nurse IOM members to assess self-reported IOM activities. Of 57 members, 47 had functioning e-mail addresses, and 33 usable responses were received. The survey consisted of 9 questions dealing with roles and responsibilities undertaken in the previous 5 years. Data analyses were descriptive. The data suggest that nurses have made considerable contributions to the IOM and their participation seems to be as high, or higher, than other disciplines. In an era of health care reform, there is additional opportunity for nurse IOM members to enhance their work in the IOM. Copyright © 2012 Elsevier Inc. All rights reserved.

Shielding member for thermonuclear device

Energy Technology Data Exchange (ETDEWEB)

Onozuka, Masanori

1997-06-30

In a thermonuclear device for shielding fast neutrons by shielding members disposed in a shielding vessel (vacuum vessel and structures such as a blanket disposed in the vacuum vessel), the shielding member comprises a large number of shielding wires formed fine and short so as to have elasticity. The shielding wires are sealed in a shielding vessel together with water, and when the width of the shielding vessel is changed, the shielding wires follow after the change of the width while elastically deforming in the shielding vessel, so that great stress and deformation are not formed thereby enabling to improve reliability. In addition, the length, the diameter and the shape of each of the shielding wires can be selected in accordance with the shielding space of the shielding vessel. Even if the shape of the shielding vessel is complicated, the shielding wires can be inserted easily. Accordingly, the filling rate of the shielding members can be changed easily. It can be produced more easily compared with a conventional spherical pebbles. It can be produced more easily than existent spherical shielding pebbles thereby enabling to reduce the production cost. (N.H.)

Influence of the positive prewhirl on the performance of centrifugal pumps with different airfoils

International Nuclear Information System (INIS)

Zhou, C M; Wang, H M; Huang, X; Lin, H

2012-01-01

According to the basic theory of turbomachinery design and inlet guide vanes prewhirl regulation, two different airfoils inlet guide vanes of prewhirl regulation device were designed, the influence of the positive prewhirl to the performance of centrifugal pump were studied based on different airfoils. The results show that, for a single-suction centrifugal pump: Gottingen bowed blade-type inlet guide vane adjustment effect is better than straight blade-type inlet guide; appropriate design of positive prewhirl can elevate the efficiency of centrifugal pumps. Compared with no vane conditions, the efficiency of centrifugal pump with prewhirl vanes has been greatly improved and the power consumption has been reduced significantly, while has little influence on the head.

Numerical Calculation and Experiment of Coupled Dynamics of the Differential Velocity Vane Pump Driven by the Hybrid Higher-order Fourier Non-circular Gears

Science.gov (United States)

Xu, Gaohuan; Chen, Jianneng; Zhao, Huacheng

2018-06-01

The transmission systems of the differential velocity vane pumps (DVVP) have periodic vibrations under loads. And it is not easy to find the reason. In order to optimize the performance of the pump, the authors proposed DVVP driven by the hybrid Higher-order Fourier non-circular gears and tested it. There were also similar periodic vibrations and noises under loads. Taking into account this phenomenon, the paper proposes fluid mechanics and solid mechanics simulation methodology to analyze the coupling dynamics between fluid and transmission system and reveals the reason. The results show that the pump has the reverse drive phenomenon, which is that the blades drive the non-circular gears when the suction and discharge is alternating. The reverse drive phenomenon leads the sign of the shaft torque to be changed in positive and negative way. So the transmission system produces torsional vibrations. In order to confirm the simulation results, micro strains of the input shaft of the pump impeller are measured by the Wheatstone bridge and wireless sensor technology. The relationships between strain and torque are obtained by experimental calibration, and then the true torque of input shaft is calculated indirectly. The experimental results are consistent to the simulation results. It is proven that the periodic vibrations are mainly caused by fluid solid coupling, which leads to periodic torsional vibration of the transmission system.

Renewable Energy and Proven Oil Reserves Relation: Evidence from OPEC Members

Directory of Open Access Journals (Sweden)

Mehmet Arcan TUZCU

2014-12-01

Full Text Available The well documented literature on the relation between energy consumption and climate change has been extended by the addition of renewable energy consumption. Several studies show its impact on technical efficiency, per capita income or carbon dioxide (CO2 emission levels for developed and developing countries. However, to the extent of our knowledge, very few of them state the importance of renewable energy for the countries where the main type of fossil fuels, oil, is exported. This study aims to explore the association between renewable energy, real gross domestic product (GDP, CO2 emission level, real oil prices as well as the proven oil reserves for seven members of Organization of the Petroleum Exporting Countries (OPEC. The analyses are conducted using panel data techniques, namely fixed effect – random effect tests. Our results show a positive and significant relation between renewable energy consumption, and real GDP and CO2 emission level. A statistically not significant coefficient is found for the relation between renewable energy and the proven oil reserves. The relation between energy and real oil prices is also insignificant.

Laser-Induced Fluorescence and Synthetic Jet Fuel Analysis in the Ultra Compact Combustor

Science.gov (United States)

2009-12-01

Performance Turbine Engine Technology ICCD Intensifying Charge Couple Device IGV Inlet guide vanes ISSI Innovative Scientific Solutions Inc. ITB...centerbody in Fig. 5 simulate inlet guide vanes ( IGV ) or stator blades. In each airfoil, there is a radial vane cavity (RVC) establishing an intermediate

New offer for our members

CERN Document Server

Staff Association

2018-01-01

Evolution 2, your specialist for Outdoor Adventures Be it for a ski lesson, a parachute jump or for a mountain bike descent, come live an unforgettable experience with our outdoor specialists. Benefit from a 10 % discount on all activities: Offer is open to SA members and their family members living in the same household, upon presentation of the membership card. Offer available for all bookings made between 1 June 2018 and 30 May 2019. Offer available on all the Evoltion2 sites. A wide range of summer and winter activities. More information on http://evolution2.com/ Contact and reservation : +33 (0)4.50.02.63.35 management@evolution2.com

Satisfaction with virtual communities of interest : Effect on members' visit frequency

NARCIS (Netherlands)

de Valck, Kristine; Langerak, Fred; Verhoef, Peter C.; Verlegh, Peeter W. J.

The authors develop a four-dimensional scale to measure members' satisfaction with virtual communities of interest (VCIs). The dimensions consist of members' satisfaction with member-to-member interactions, organizer-to-member interactions and organizer-to-community interactions, all of which come

Motivational climate, staff and members' behaviors, and members' psychological well-being at a national fitness franchise.

Science.gov (United States)

Brown, Theresa C; Fry, Mary D

2014-06-01

The purpose of this study was to examine the association between members' perceptions of staffs behaviors, motivational climate, their own behaviors, commitment to future exercise, and life satisfaction in a group-fitness setting. The theory-driven hypothesized mediating role of perceptions of the climate was also tested. Members (N = 5,541) of a national group-fitness studio franchise completed a survey regarding their class experiences. The survey included questions that measured participants' perceptions of the motivational climate (caring, task-involving, ego-involving), perceptions of staff's behaviors, their own behaviors, commitment to exercise, and life satisfaction. Structural equation modeling was used to assess both the association between variables and the theoretically driven predictive relationships. The participants perceived the environment as highly caring and task-involving and low ego-involving. They reported high exercise commitment and moderately high life satisfaction and perceived that the staffs and their own behaviors reflected caring, task-involving characteristics. Structural equation modeling demonstrated that those who perceived a higher caring, task-involving climate and lower ego-involving climate were more likely to report more task-involving, caring behaviors among the staff and themselves as well as greater commitment to exercise. In addition, a theory-driven mediational model suggested that staff behaviors may be an antecedent to members' exercise experiences by impacting their perceptions of the climate. The results of this study give direction to specific behaviors in which staff of group-fitness programs might engage to positively influence members' exercise experiences.

Party member recruitment and the representativeness of party membership

DEFF Research Database (Denmark)

Kosiara-Pedersen, Karina

Party membership figures are in decline. However, parties are still recruiting party members. Are there any differences in the social and political characteristics of old and new party members? If there is a difference, are new party members more or less representative for party voters than old...

48 CFR 1305.403 - Requests from Members of Congress.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Requests from Members of Congress. 1305.403 Section 1305.403 Federal Acquisition Regulations System DEPARTMENT OF COMMERCE... from Members of Congress. Requests from Members of Congress shall be handled in accordance with the...

CERN welcomes new members

Science.gov (United States)

2017-08-01

Lithuania is on course to become an associate member of CERN, pending final approval by the Lithuanian parliament. Associate membership will allow representatives of the Baltic nation to take part in meetings of the CERN Council, which oversees the Geneva-based physics lab.

Supporting Members and Friends

Science.gov (United States)

2005-10-01

Thank you! Over the past year, AGU has received 12,104 gifts, both large and small, from members and friends. The Union has also received corporate contributions, National Science Foundation grants, and support from the National Oceanographic Partnership Program and National Association of Geoscience Teachers. Together their generosity has benefited AGU non revenue producing programs that are critical to our science and the future health of the Union. The following list gratefully acknowledges annual gifts of $100 or more and cumulative giving of $5,000 or more. The 1919 Society ($100,000 or more) and Benefactors ($5,000-$99,999) recognize single major gifts and cumulative contributions. Three circles acknowledge annual giving: President's Circle ($1,000 or more), Leadership Circle ($200-$999), and Supporters Circle ($100-$199). Supporting Life Members, who contribute a one-time gift of $1,200 in addition to lifetime dues, are among our most loyal Supporters.

Technological Packages Extended To Farmers by Non ...

African Journals Online (AJOL)

Global Approaches to Extension Practice: A Journal of Agricultural Extension ... extended to farmers by Non Governmental Organizations in the Niger Delta area of Nigeria. ... Modern snailery was the only identified agro forestry technology extended, ... technologies were the significant soil management practices extended.

The Agency's Safeguards System (1965, as provisionally extended in 1966 and 1968); Le Systeme de Garanties de l'Agence (1965, provisoirement etendu en 1966 et 1968)

Energy Technology Data Exchange (ETDEWEB)

NONE

1968-09-24

The Agency's safeguards system, as approved by the Board of Governors in 1965, and provisionally extended in 1966, is set forth in this document for the Information of all Members [French] Le Systeme de garanties de l'Agence, approuve par le Conseil des gouverneurs en 1965 et provisoirement etendu en 1966 et 1968, est reproduit dans le present document pour l'information de tous les Membres.

77 FR 4646 - Airworthiness Directives; Bombardier, Inc. Airplanes

Science.gov (United States)

2012-01-31

... angle of attack vanes, pitot probes, engine inlets, and windshields, and consequent loss of or... of attack vanes, pitot probes, engine inlets or windshields. In icing conditions, the loss of the ice... of attack vanes, pitot probes, engine inlets, and windshields, and consequent loss of or misleading...

49 CFR 805.735-10 - Member and employee indebtedness.

Science.gov (United States)

2010-10-01

... TRANSPORTATION SAFETY BOARD EMPLOYEE RESPONSIBILITIES AND CONDUCT § 805.735-10 Member and employee indebtedness. Members and employees shall pay each just financial obligation in a proper and timely manner, especially... 49 Transportation 7 2010-10-01 2010-10-01 false Member and employee indebtedness. 805.735-10...

[Ballistic concepts and management of gunshot wounds at members].

Science.gov (United States)

Fabeck, L; Hock, N; Goffin, J; Ngatchou, W

2017-01-01

Ballistic trauma is not the prerogative of battlefields and currently extends to civil environments. Any surgeon or emergency room can be faced with such trauma whose management requires an understanding of wound ballistics. The aim of this retrospective is reviewing the management of ballistic trauma within the C.H.U. Saint-Pierre hospital over a period of ten years. Data recorded included demographics data, lesions, clinical parameters, imaging, treatment and outcome. It appears that the wounds of the members have a low mortality rate but a significant rate of complications. Patients should be managed according to the ATLS protocol and according hemodynamic stability and location of the injury, benefit from imaging. Unstable patients will be operated in emergency, stable patients will be treated according to the extent of damage and the type of fracture either conservatively or by external fixator and intramedullary centromedullary. Debridement and antibiotics are recommended as a nerve exploration if there is a peripheral paralysis. The management of trauma in our sample appear not optimal in light of the literature especially in terms of setting the vascular point of debridement, antibiotic and nerve repair resulting in significant consequences. Two management protocols according to patients' hemodynamic status are offered.

A static investigation of the thrust vectoring system of the F/A-18 high-alpha research vehicle

Science.gov (United States)

Mason, Mary L.; Capone, Francis J.; Asbury, Scott C.

1992-01-01

A static (wind-off) test was conducted in the static test facility of the Langley 16-foot Transonic Tunnel to evaluate the vectoring capability and isolated nozzle performance of the proposed thrust vectoring system of the F/A-18 high alpha research vehicle (HARV). The thrust vectoring system consisted of three asymmetrically spaced vanes installed externally on a single test nozzle. Two nozzle configurations were tested: A maximum afterburner-power nozzle and a military-power nozzle. Vane size and vane actuation geometry were investigated, and an extensive matrix of vane deflection angles was tested. The nozzle pressure ratios ranged from two to six. The results indicate that the three vane system can successfully generate multiaxis (pitch and yaw) thrust vectoring. However, large resultant vector angles incurred large thrust losses. Resultant vector angles were always lower than the vane deflection angles. The maximum thrust vectoring angles achieved for the military-power nozzle were larger than the angles achieved for the maximum afterburner-power nozzle.