The Potential for Wind Energy Meeting Electricity Needs on Vancouver Island

OpenAIRE

Ryan Prescott; G. Cornelis van Kooten; Hui Zhu

2006-01-01

In this paper, an in-depth analysis of power supply and demand on Vancouver Island is used to provide information about the optimal allocation of power across ‘generating’ sources and to investigate the economics of wind generation and penetrability into the Island grid. The methodology developed can be extended to a region much larger than Vancouver Island. Results from the model indicate that Vancouver Island could experience blackouts in the near future unless greater name-plate capacity i...

Surficial Geology of Mount Rainier National Park, Washington

Science.gov (United States)

Crandell, Dwight Raymond

1969-01-01

Much of the ground surface around Mount Rainier volcano is directly underlain by loose geologic deposits that veneer the hard rock formations. Examples of these deposits are sand and gravel bars along the rivers, ridges of loose rock debris beside the glaciers, and sloping aprons of rock fragments beneath almost every cliff. Even though they are generally thin and inconspicuous when compared with the rock formations, these surficial deposits are clues to geologic events that have profoundly influenced the shape of the park's landscape. Thus, from the character and extent of glacial deposits one can judge the age and size of former glaciers that carved the cirques and deep canyons of the park; from the mudflows which streamed down nearly every valley one can infer the age and size of huge landslides of the past that helped determine Mount Rainier's present shape; and from the pumice deposits some of the volcano's recent eruptive activity can be reconstructed. The map (plate 1, in pocket) that accompanies this description of the surficial deposits of Mount Rainier National Park shows the location of the various geologic formations, and the explanation shows the formations arranged in order of their relative age, with the oldest at the bottom. The text describes the surficial deposits in sequence from older to younger. A discussion of the pumice deposits of the park, which were not mapped, is followed by a description of the formations shown on the geologic map. Inspection of the geologic map may lead the viewer to question why the surficial deposits are shown in more detail in a zone several miles wide around the base of the volcano than elsewhere. This is partly because the zone is largely near or above timberline, relatively accessible, and the surficial deposits there can be readily recognized, differentiated, and mapped. In contrast, access is more difficult in the heavily timbered parts of the park, and surficial deposits there are generally blanketed by a dense

Climate change vulnerability and adaptation in the North Cascades region, Washington

Science.gov (United States)

Crystal L. Raymond; David L. Peterson; Regina M. Rochefort

2014-01-01

The North Cascadia Adaptation Partnership (NCAP) is a science-management partnership consisting of the U.S. Department of Agriculture Forest Service Mount Baker-Snoqualmie and Okanogan-Wenatchee National Forests and Pacific Northwest Research Station; North Cascades National Park Complex; Mount Rainier National Park; and University of Washington Climate Impacts Group....

Vancouver Accelerator Conference

Energy Technology Data Exchange (ETDEWEB)

Anon.

1985-06-15

Anyone who contends that particle physics is conducted in an ivory tower, not contributing to other fields of science or to humanity at large, should have attended the 1985 Particle Accelerator Conference in Vancouver. Over a thousand participants contributed 781 papers and only a fraction were actually related to accelerators for high energy physics. The majority of present developments are in the service of other fields of science, for alternative power sources, for medicine, for industrial applications, etc.

Vancouver Accelerator Conference

International Nuclear Information System (INIS)

Anon.

1985-01-01

Anyone who contends that particle physics is conducted in an ivory tower, not contributing to other fields of science or to humanity at large, should have attended the 1985 Particle Accelerator Conference in Vancouver. Over a thousand participants contributed 781 papers and only a fraction were actually related to accelerators for high energy physics. The majority of present developments are in the service of other fields of science, for alternative power sources, for medicine, for industrial applications, etc

Seasonal distribution and aerial surveys of mountain goats in Mount Rainier, North Cascades, and Olympic National Parks, Washington

Science.gov (United States)

Jenkins, Kurt; Beirne, Katherine; Happe, Patricia; Hoffman, Roger; Rice, Cliff; Schaberl, Jim

2011-01-01

We described the seasonal distribution of Geographic Positioning System (GPS)-collared mountain goats (Oreamnos americanus) in Mount Rainier, North Cascades, and Olympic National Parks to evaluate aerial survey sampling designs and provide general information for park managers. This work complemented a companion study published elsewhere of aerial detection biases of mountain goat surveys in western Washington. Specific objectives reported here were to determine seasonal and altitudinal movements, home range distributions, and temporal dynamics of mountain goat movements in and out of aerial survey sampling frames established within each park. We captured 25 mountain goats in Mount Rainier (9), North Cascades (5), and Olympic (11) National Parks, and fitted them with GPS-collars programmed to obtain 6-8 locations daily. We obtained location data on 23 mountain goats for a range of 39-751 days from 2003 to 2008. Altitudinal distributions of GPS-collared mountain goats varied individually and seasonally, but median altitudes used by individual goats during winter ranged from 817 to 1,541 meters in Olympic and North Cascades National Parks, and 1,215 to 1,787 meters in Mount Rainier National Park. Median altitudes used by GPS-collared goats during summer ranged from 1,312 to 1,819 meters in Olympic and North Cascades National Parks, and 1,780 to 2,061 meters in Mount Rainier National Park. GPS-collared mountain goats generally moved from low-altitude winter ranges to high-altitude summer ranges between June 11 and June 19 (range April 24-July 3) and from summer to winter ranges between October 26 and November 9 (range September 11-December 23). Seasonal home ranges (95 percent of adaptive kernel utilization distribution) of males and female mountain goats were highly variable, ranging from 1.6 to 37.0 kilometers during summers and 0.7 to 9.5 kilometers during winters. Locations of GPS-collared mountain goats were almost 100 percent within the sampling frame used for

Evidence for fluid-triggered slip in the 2009 Mount Rainier, Washington earthquake swarm

Science.gov (United States)

Shelly, David R.; Moran, Seth C.; Thelen, Weston A.

2013-01-01

A vigorous swarm of over 1000 small, shallow earthquakes occurred 20–22 September 2009 beneath Mount Rainier, Washington, including the largest number of events ever recorded in a single day at Rainier since seismic stations were installed on the edifice in 1989. Many events were only clearly recorded on one or two stations on the edifice, or they overlapped in time with other events, and thus only ~200 were locatable by manual phase picking. To partially overcome this limitation, we applied waveform-based event detection integrated with precise double-difference relative relocation. With this procedure, detection and location goals are accomplished in tandem, using cross-correlation with continuous seismic data and waveform templates constructed from cataloged events. As a result, we obtained precise locations for 726 events, an improvement of almost a factor of 4. These event locations define a ~850 m long nearly vertical structure striking NNE, with episodic migration outward from the initial hypocenters. The activity front propagates in a manner consistent with a diffusional process. Double-couple-constrained focal mechanisms suggest dominantly near-vertical strike-slip motion on either NNW or ENE striking faults, more than 30° different than the strike of the event locations. This suggests the possibility of en echelon faulting, perhaps with a component of fault opening in a fracture-mesh-type geometry. We hypothesize that the swarm was initiated by a sudden release of high-pressure fluid into preexisting fractures, with subsequent activity triggered by diffusing fluid pressure in combination with stress transfer from the preceding events.

The use of environmental assessment in port management: The case of Vancouver, B.C

International Nuclear Information System (INIS)

Georgison, J.P.; Day, J.C.

1991-01-01

The approach adopted to assess the environmental impacts of development proposals in the Port of Vancouver is analyzed. The institutional and regulatory system for managing Canada's largest port is examined to identify opportunities for, and impediments to, application of effective environmental impact assessments. The Exxon Valdez and Nestucca, Washington incidents increased public awareness and concern regarding the magnitude and effect of bulk liquid commodity spills along the Canadian west coast. In September 1990, the federally mandated Public Review Panel on Tanker Safety and Marine Spills Response Capability concluded that environmental assessment and review of terminal expansion proposals must address the impact of expanded liquid cargo shipments on surrounding communities and risk to air and water quality. It is recommended that assessment consistency, comprehensiveness, and objectiveness should be defined through formulation of legally binding regulations under the forthcoming Canadian Environmental Assessment Act. 23 refs., 1 fig

Erosion by flowing lava: Geochemical evidence in the Cave Basalt, Mount St. Helens, Washington

Science.gov (United States)

Williams, D.A.; Kadel, S.D.; Greeley, R.; Lesher, C.M.; Clynne, M.A.

2004-01-01

We sampled basaltic lava flows and underlying dacitic tuff deposits in or near lava tubes of the Cave Basalt, Mount St. Helens, Washington to determine whether the Cave Basalt lavas contain geochemical evidence of substrate contamination by lava erosion. The samples were analyzed using a combination of wavelength-dispersive X-ray fluorescence spectrometry and inductively-coupled plasma mass spectrometry. The results indicate that the oldest, outer lava tube linings in direct contact with the dacitic substrate are contaminated, whereas the younger, inner lava tube linings are uncontaminated and apparently either more evolved or enriched in residual liquid. The most heavily contaminated lavas occur closer to the vent and in steeper parts of the tube system, and the amount of contamination decreases with increasing distance downstream. These results suggest that erosion by lava and contamination were limited to only the initially emplaced flows and that erosion was localized and enhanced by vigorous laminar flow over steeper slopes. After cooling, the initial Cave Basalt lava flows formed an insulating lining within the tubes that prevented further erosion by later flows. This interpretation is consistent with models of lava erosion that predict higher erosion rates closer to sources and over steeper slopes. A greater abundance of xenoliths and xenocrysts relative to xenomelts in hand samples indicates that mechanical erosion rather than thermal erosion was the dominant erosional process in the Cave Basalt, but further sampling and petrographic analyses must be performed to verify this hypothesis. ?? Springer-Verlag 2003.

Pubs in Public Life: A Place for Liquor Spaces in the City of Vancouver

OpenAIRE

Forbes, Heather

2010-01-01

Vancouver liquor licensing bylaws has been described by members of the media, industry, government and general public as overly restrictive, especially in the areas of hours ofservice, geographical distribution and the cultural diversity ofpublic liquor spaces. According to the City of Vancouver, the objective of city stewardship is to provide for the social, economic and physical well-being of citizens. A consultation of both academic research and the Vancouver community suggests that public...

Sedimentology, Behavior, and Hazards of Debris Flows at Mount Rainier, Washington

Science.gov (United States)

Scott, K.M.; Vallance, J.W.; Pringle, P.T.

1995-01-01

Mount Rainier is potentially the most dangerous volcano in the Cascade Range because of its great height, frequent earthquakes, active hydrothermal system, and extensive glacier mantle. Many debris flows and their distal phases have inundated areas far from the volcano during postglacial time. Two types of debris flows, cohesive and noncohesive, have radically different origins and behavior that relate empirically to clay content. The two types are the major subpopulations of debris flows at Mount Rainier. The behavior of cohesive flows is affected by the cohesion and adhesion of particles; noncohesive flows are dominated by particle collisions to the extent that particle cataclasis becomes common during near-boundary shear. Cohesive debris flows contain more than 3 to 5 percent of clay-size sediment. The composition of these flows changed little as they traveled more than 100 kilometers from Mount Rainier to inundate parts of the now-populated Puget Sound lowland. They originate as deep-seated failures of sectors of the volcanic edifice, and such failures are sufficiently frequent that they are the major destructional process of Mount Rainier's morphologic evolution. In several deposits of large cohesive flows, a lateral, megaclast-bearing facies (with a mounded or hummocky surface) contrasts with a more clay-rich facies in the center of valleys and downstream. Cohesive flows at Mount Rainier do not correlate strongly with volcanic activity and thus can recur without warning, possibly triggered by non-magmatic earthquakes or by changes in the hydrothermal system. Noncohesive debris flows contain less than 3 to 5 percent clay-size sediment. They form most commonly by bulking of sediment in water surges, but some originate directly or indirectly from shallow slope failures that do not penetrate the hydrothermally altered core of the volcano. In contrast with cohesive flows, most noncohesive flows transform both from and to other flow types and are, therefore, the

Correlations of turbidity to suspended-sediment concentration in the Toutle River Basin, near Mount St. Helens, Washington, 2010-11

Science.gov (United States)

Uhrich, Mark A.; Kolasinac, Jasna; Booth, Pamela L.; Fountain, Robert L.; Spicer, Kurt R.; Mosbrucker, Adam R.

2014-01-01

Researchers at the U.S. Geological Survey, Cascades Volcano Observatory, investigated alternative methods for the traditional sample-based sediment record procedure in determining suspended-sediment concentration (SSC) and discharge. One such sediment-surrogate technique was developed using turbidity and discharge to estimate SSC for two gaging stations in the Toutle River Basin near Mount St. Helens, Washington. To provide context for the study, methods for collecting sediment data and monitoring turbidity are discussed. Statistical methods used include the development of ordinary least squares regression models for each gaging station. Issues of time-related autocorrelation also are evaluated. Addition of lagged explanatory variables was used to account for autocorrelation in the turbidity, discharge, and SSC data. Final regression model equations and plots are presented for the two gaging stations. The regression models support near-real-time estimates of SSC and improved suspended-sediment discharge records by incorporating continuous instream turbidity. Future use of such models may potentially lower the costs of sediment monitoring by reducing time it takes to collect and process samples and to derive a sediment-discharge record.

Spread of Rare Fungus from Vancouver Island

Centers for Disease Control (CDC) Podcasts

Cryptococcus gattii, a rare fungus normally found in the tropics, has infected people and animals on Vancouver Island, Canada. Dr. David Warnock, Director, Division of Foodborne, Bacterial, and Mycotic Diseases, CDC, discusses public health concerns about further spread of this organism

Traveling to Canada for the Vancouver 2010 Winter Olympic and Paralympic Games.

Science.gov (United States)

Heggie, Travis W

2009-07-01

The 21st Winter Olympic Games will be held in Vancouver, British Columbia, Canada from February 12 to 28, 2010. Following the Winter Olympic Games, the Winter Paralympic Games will be held from March 12 to 21, 2010. There will be 86 winter sporting events hosted in Vancouver with 5500 athletes staying in two Olympic Villages. Another 2800 members of the media, 25,000 volunteers, and 1 million spectators are expected in attendance. This paper reviews health and safety issues for all travelers to Canada for the 2010 Vancouver Winter Olympic Games with a specific focus on pre-travel planning, road and transportation safety in British Columbia, natural and environmental hazards, Olympic medical facilities, safety and security, and infectious disease.

Quality of ground water in Clark County, Washington, 1988

International Nuclear Information System (INIS)

Turney, G.L.

1990-01-01

Water samples were collected from 76 wells throughout Clark County, in southwest Washington, during April and May 1988, and were analyzed from concentrations of major ions, silica, nitrate, phosphorus, aluminum, manganese, radon, and bacteria. Samples from 20 wells were analyzed for concentrations of trace elements and organic compounds, including most of those on the US Environmental Protection Agency (USEPA) priority pollutant list. Dissolved solids concentrations range from 12 to 245 mg/L, with a median concentration of 132 mg/L. The major dissolved constituents are calcium, bicarbonate, and silica, and, in some samples, sodium. Nitrate concentrations exceeded 1.0 mg/L throughout the Vancouver urban area, and were as large as 6.7 mg/L. Comparison with limited historical data indicates that nitrate concentrations were somewhat correlated, possibly indicating similar sources. Volatile organic compound, including tetrachloroethane and 1,1,1-trichloroethane, were detected in samples from three wells in the Vancouver area. Trace amounts of volatile organic compounds were reported in samples from several other wells, but at concentrations too close to analytical detection limits to ascertain that they were in the groundwater. Trace elements and radiochemical constituents were present at small levels indicating natural sources for these constituents. Only pH, turbidity, iron, manganese, and total coliform bacteria had values that did not meet USEPA Drinking Water Standards

Page from the Log Book of the USS "Harriet Lane" and Painting by Thomas P. Rossiter, Related to the Prince of Wales's 1860 Visit to Mount Vernon

Science.gov (United States)

Potter, Lee Ann; Eder, Elizabeth K.; Hussey, Michael

2011-01-01

On 1860, Prince Albert Edward took a daylong excursion aboard the 270-foot revenue cutter USS "Harriet Lane" to Mount Vernon, the ancestral home of George Washington. The ceremonial visit to Mount Vernon was thought of at the time as not only a tribute to Washington as a man and leader, but as symbolic of reconciliation between England and its…

Network constrained wind integration on Vancouver Island

NARCIS (Netherlands)

Maddaloni, J.D.; Rowe, A.M.; Kooten, van G.C.

2008-01-01

The aim of this study is to determine the costs and carbon emissions associated with operating a hydro-dominated electricity generation system (Vancouver Island, Canada) with varying degrees of wind penetration. The focus is to match the wind resource, system demand and abilities of extant

Trends in temperature and dew point at the summit of Mount Washington, New Hampshire, 1935-2004.

Science.gov (United States)

Grant, A. N.; Pszenny, A. A.; Fischer, E. V.

2005-05-01

Dry and wet bulb temperatures from sling psychrometer measurements taken every six hours from 1935 to 2004 at the summit of Mount Washington, located at 44 °16'N, 71 °18'W, 1914 m ASL have recently been digitized. Annual temperature has increased by 0.3°C, and annual dew point has decreased by 0.4°C over this 70-year period. Synoptic temperature has increased most in spring and winter, changing by 1.0°C and 0.5°C, respectively, while it has decreased slightly in summer and fall. Dew point has decreased in fall, summer, and winter, 0.9°C, 0.5°C, and 0.4°C respectively, and increased by 0.1°C in spring. Preliminary analysis suggests that some of the larger trends in winter and spring may be statistically significant; results of Monte Carlo simulations will be reported. Changes in dew point may be attributed to two factors. Decreasing dew points are expected if the temperature increases but the amount of water vapor present stays the same. Alternatively, lower dew points could be indicative of the presence of drier air. Other dew point climatologies of the continental United States for the second half of the century have shown mixed results, with increased dew points evident at some stations, decreased dew points at others, and no clear regional patterns.

Long-term autonomous volcanic gas monitoring with Multi-GAS at Mount St. Helens, Washington, and Augustine Volcano, Alaska

Science.gov (United States)

Kelly, P. J.; Ketner, D. M.; Kern, C.; Lahusen, R. G.; Lockett, C.; Parker, T.; Paskievitch, J.; Pauk, B.; Rinehart, A.; Werner, C. A.

2015-12-01

In recent years, the USGS Volcano Hazards Program has worked to implement continuous real-time in situ volcanic gas monitoring at volcanoes in the Cascade Range and Alaska. The main goal of this ongoing effort is to better link the compositions of volcanic gases to other real-time monitoring data, such as seismicity and deformation, in order to improve baseline monitoring and early detection of volcanic unrest. Due to the remote and difficult-to-access nature of volcanic-gas monitoring sites in the Cascades and Alaska, we developed Multi-GAS instruments that can operate unattended for long periods of time with minimal direct maintenance from field personnel. Our Multi-GAS stations measure H2O, CO2, SO2, and H2S gas concentrations, are comprised entirely of commercial off-the-shelf components, and are powered by small solar energy systems. One notable feature of our Multi-GAS stations is that they include a unique capability to perform automated CO2, SO2, and H2S sensor verifications using portable gas standards while deployed in the field, thereby allowing for rigorous tracking of sensor performances. In addition, we have developed novel onboard data-processing routines that allow diagnostic and monitoring data - including gas ratios (e.g. CO2/SO2) - to be streamed in real time to internal observatory and public web pages without user input. Here we present over one year of continuous data from a permanent Multi-GAS station installed in August 2014 in the crater of Mount St. Helens, Washington, and several months of data from a station installed near the summit of Augustine Volcano, Alaska in June 2015. Data from the Mount St. Helens Multi-GAS station has been streaming to a public USGS site since early 2015, a first for a permanent Multi-GAS site. Neither station has detected significant changes in gas concentrations or compositions since they were installed, consistent with low levels of seismicity and deformation.

Is Climate influencing Cryptococcus gattii on Vancouver Island?

Centers for Disease Control (CDC) Podcasts

2016-03-24

Dr. Christopher Uejio, Department of Geography and Program in Public Health, Florida State University, discusses Cryptococcus gattii on Vancouver Island.  Created: 3/24/2016 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 3/24/2016.

Command and Control Analysis of the South West Provincial Regional Emergency Operations Centre during Vancouver 2010

Science.gov (United States)

2011-06-01

Venue Site WACC - Whistler Area Command Centre OTHER GPPAG - Government Partners Public Affairs Group 18 ANNEX B. Interview questions...Vancouver Vancouver Richmond WACC Decision Authority Link Information Sharing Link DOC’s 2010 Provincial Games Secretariat GPPAG CCG

Spread of Rare Fungus from Vancouver Island

Centers for Disease Control (CDC) Podcasts

2006-12-20

Cryptococcus gattii, a rare fungus normally found in the tropics, has infected people and animals on Vancouver Island, Canada. Dr. David Warnock, Director, Division of Foodborne, Bacterial, and Mycotic Diseases, CDC, discusses public health concerns about further spread of this organism.  Created: 12/20/2006 by Emerging Infectious Diseases.   Date Released: 12/29/2006.

Hard to Stomach: Food Insecurity and Inequitable Access to Nutritious Food in Vancouver

OpenAIRE

Moe, Jennifer Lauren

2014-01-01

Food insecurity is a problem in Vancouver, BC. Through analysis of the systemic causes and negative correlates of food insecurity, this study examines effective ways to mitigate food insecurity in Vancouver by enabling consistent access to sufficient, nutritious food. Assessments of the economics of food insecurity and multi-level governmental positions on the issue provide a theoretical and practical basis for the research. A literature review and four in-depth stakeholder interviews identif...

Update on the Vancouver Fuel Cell Vehicle Program

International Nuclear Information System (INIS)

Rothwell, B.

2004-01-01

'Full text:' The Vancouver Fuel Cell Vehicle Program (VFCVP) is a $5.8 million initiative designed to test four Ford Focus Fuel Cell Vehicles for three years in the Lower Mainland of British Columbia. The project is the first of its kind in Canada and is led by Fuel Cells Canada (FCC), the Ford Motor Company (Ford), and the Governments of Canada and British Columbia. This presentation will provide program details and an update on activities leading up to currently planned delivery to Vancouver in November 2004. The VFCVP will test the performance, durability and reliability of the Ford fuel cell vehicle cars in real-world conditions and will examine fuelling issues and solutions, the reduction of greenhouse gas emissions and public acceptance of hydrogen fuel cell vehicles. The program will generate data to help evolve the technology and develop international codes and standards E cents Epnd the implementation and adoption of fuel cell technology. (author)

Soil and air temperatures for different habitats in Mount Rainier National Park.

Science.gov (United States)

Sarah E. Greene; Mark Klopsch

1985-01-01

This paper reports air and soil temperature data from 10 sites in Mount Rainier National Park in Washington State for 2- to 5-year periods. Data provided are monthly summaries for day and night mean air temperatures, mean minimum and maximum air temperatures, absolute minimum and maximum air temperatures, range of air temperatures, mean soil temperature, and absolute...

Waste management in Greater Vancouver

Energy Technology Data Exchange (ETDEWEB)

Carrusca, K. [Greater Vancouver Regional District, Burnaby, BC (Canada); Richter, R. [Montenay Inc., Vancouver, BC (Canada)]|[Veolia Environmental Services, Vancouver, BC (Canada)

2006-07-01

An outline of the Greater Vancouver Regional District (GVRD) waste-to-energy program was presented. The GVRD has an annual budget for solid waste management of $90 million. Energy recovery revenues from solid waste currently exceed $10 million. Over 1,660,00 tonnes of GVRD waste is recycled, and another 280,000 tonnes is converted from waste to energy. The GVRD waste-to-energy facility combines state-of-the-art combustion and air pollution control, and has processed over 5 million tonnes of municipal solid waste since it opened in 1988. Its central location minimizes haul distance, and it was originally sited to utilize steam through sales to a recycle paper mill. The facility has won several awards, including the Solid Waste Association of North America award for best facility in 1990. The facility focuses on continual improvement, and has installed a carbon injection system; an ammonia injection system; a flyash stabilization system; and heat capacity upgrades in addition to conducting continuous waste composition studies. Continuous air emissions monitoring is also conducted at the plant, which produces a very small percentage of the total air emissions in metropolitan Vancouver. The GVRD is now seeking options for the management of a further 500,000 tonnes per year of solid waste, and has received 23 submissions from a range of waste energy technologies which are now being evaluated. It was concluded that waste-to-energy plants can be located in densely populated metropolitan areas and provide a local disposal solution as well as a source of renewable energy. Other GVRD waste reduction policies were also reviewed. refs., tabs., figs.

A Cross-Sectional Analysis of Acute Hepatitis B Virus Reported to the Vancouver Coastal Health Authority from 2000 to 2003

Directory of Open Access Journals (Sweden)

Yvette Leung

2006-01-01

Full Text Available BACKGROUND: Acute hepatitis B virus (HBV transmission remains a significant public health problem despite effective vaccination and prophylaxis strategies. Vancouver, British Columbia, has a large ethnic community from endemic areas, which may further impact on the epidemiology of acute HBV. A cross-sectional study of factors associated with acute HBV cases reported to the Vancouver Coastal Health Authority (Vancouver, British Columbia from 2000 to 2003 is reported.

Shaded Relief with Height as Color, Mount Meru, Tanzania

Science.gov (United States)

2002-01-01

Mount Meru is an active volcano located just 70 kilometers (44 miles) west of Mount Kilimanjaro. It reaches 4,566 meters (14,978 feet) in height but has lost much of its bulk due to an eastward volcanic blast sometime in its distant past, perhaps similar to the eruption of Mount Saint Helens in Washington State in 1980. Mount Meru most recently had a minor eruption about a century ago. The several small cones and craters seen in the vicinity probably reflect numerous episodes of volcanic activity. Mount Meru is the topographic centerpiece of Arusha National Park. Its fertile slopes rise above the surrounding savanna and support a forest that hosts diverse wildlife, including nearly 400 species of birds, and also monkeys and leopards.Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the north-south direction. Northern slopes appear bright and southern slopes appear dark, as would be the case at noon at this latitude in June. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow, red, and magenta, to blue and white at the highest elevations.Elevation data used in this image was acquired by the Shuttle Radar Topography Mission (SRTM) aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Imagery and Mapping Agency (NIMA) of the U.S. Department of Defense and the German and Italian space

Additions to the stoneflies (Plecoptera) of Mount Rainier National Park, Washington, U.S.A.

Science.gov (United States)

Kondratieff, B.C.; Lechleitner, R.A.; Zuellig, R.E.

2006-01-01

In summary, 88 species of stoneflies are now known from MRNP, representing 65% of the recorded Washington State fauna (Stark and Baumann 2005). At least two of these species are apparently restricted to the MRNP, Soliperla fenderi (Jewett) (Stark and Gustafson 2004) and P. lechleitneri.

Forest insect and disease conditions, Vancouver forest region, 1986. Annual publication

Energy Technology Data Exchange (ETDEWEB)

Humphreys, N; Ferris, R L

1987-01-01

This report outlines the status of forest pest conditions in the Vancouver Forest Region, and forecasts population trends of some potentially damaging pests. Pests are listed by host in order of importance.

Attracting new advertisers and retaining old ones: carving a niche in Vancouver's city magazine market

OpenAIRE

McCready, Kathryn Elizabeth

2009-01-01

This report examines city magazine advertising in Vancouver. It explores the types of advertisers that use this medium, their marketing needs, the range of media in Vancouver that attempt to satisfy these needs, and how these local businesses plan and execute their media campaigns. It uses a case study of a city magazine, VLM to explore and analyse the advertising sales process. It provides an overview of the changes in editorial, circulation and advertising strategy that VLM introduced in 20...

Contests over social memory in waterfront Vancouver: Historical editing & obfuscation through public art

Directory of Open Access Journals (Sweden)

Gordon Brent Ingram

2000-02-01

Full Text Available Every public art site has a relationship to the history of surrounding areas whether in obscuring social memory or in highlighting certain relationships and events over others. Over the last decade, much of central Vancouver's waterfront, particularly around False Creek (a marine inlet, has been redeveloped with international capital - much of which has been linked to Hong Kong. Several large redevelopment areas have involved close cooperation in urban design processes between `the city' and `the developer'. In these megaprojects, public art has emerged as a more substantial and stable urban amenity while becoming less overtly ideological and associated with democratic public space. In this part of North America, such relatively public art projects have become almost iconographic for economic and social changes associated with globalization. Contentious historical information has tended to be censored - particularly around a range of non-European communities and events over the last century involving social conflict. In the same period, outdoor art has been increasingly used as a part of strategies to reclaim public space and attempts to democratize it. These two kinds and functions of public art have tended to be used for divergent experiences of the relationships of history to the present, of public space and the existence of and responses to social conflict, and of `sense of place'. Six public art sites, with four built, along the north shore of False Creek, in central Vancouver, are analyzed in terms of their cultural, urban and spatial politics and, in particular, in terms of contemporary tensions around the extent of aboriginal presence before and after the arrival of Europeans, the multiracial and multicultural origins and character of the city, contamination with toxic chemicals, violence against women, and the AIDS pandemic. A method for better analyzing the cultural politics of public art sites (and the design processes that were

Mount St. Helens: Controlled-source audio-frequency magnetotelluric (CSAMT) data and inversions

Science.gov (United States)

Wynn, Jeff; Pierce, Herbert A.

2015-01-01

This report describes a series of geoelectrical soundings carried out on and near Mount St. Helens volcano, Washington, in 2010–2011. These soundings used a controlled-source audio-frequency magnetotelluric (CSAMT) approach (Zonge and Hughes, 1991; Simpson and Bahr, 2005). We chose CSAMT for logistical reasons: It can be deployed by helicopter, has an effective depth of penetration of as much as 1 kilometer, and requires less wire than a Schlumberger sounding.

Network constrained wind integration on Vancouver Island

International Nuclear Information System (INIS)

Maddaloni, Jesse D.; Rowe, Andrew M.; Kooten, G. Cornelis van

2008-01-01

The aim of this study is to determine the costs and carbon emissions associated with operating a hydro-dominated electricity generation system (Vancouver Island, Canada) with varying degrees of wind penetration. The focus is to match the wind resource, system demand and abilities of extant generating facilities on a temporal basis, resulting in an operating schedule that minimizes system cost over a given period. This is performed by taking the perspective of a social planner who desires to find the lowest-cost mix of new and existing generation facilities. Unlike other studies, this analysis considers variable efficiency for thermal and hydro-generators, resulting in a fuel cost that varies with respect to generator part load. Since this study and others have shown that wind power may induce a large variance on existing dispatchable generators, forcing more frequent operation at reduced part load, inclusion of increased fuel cost at part load is important when investigating wind integration as it can significantly reduce the economic benefits of utilizing low-cost wind. Results indicate that the introduction of wind power may reduce system operating costs, but this depends heavily on whether the capital cost of the wind farm is considered. For the Vancouver Island mix with its large hydro-component, operating cost was reduced by a maximum of 15% at a wind penetration of 50%, with a negligible reduction in operating cost when the wind farm capital cost was included

Verification of an ENSO-Based Long-Range Prediction of Anomalous Weather Conditions During the Vancouver 2010 Olympics and Paralympics

Science.gov (United States)

Mo, Ruping; Joe, Paul I.; Doyle, Chris; Whitfield, Paul H.

2014-01-01

A brief review of the anomalous weather conditions during the Vancouver 2010 Winter Olympic and Paralympic Games and the efforts to predict these anomalies based on some preceding El Niño-Southern Oscillation (ENSO) signals are presented. It is shown that the Olympic Games were held under extraordinarily warm conditions in February 2010, with monthly mean temperature anomalies of +2.2 °C in Vancouver and +2.8 °C in Whistler, ranking respectively as the highest and the second highest in the past 30 years (1981-2010). The warm conditions continued, but became less anomalous, in March 2010 for the Paralympic Games. While the precipitation amounts in the area remained near normal through this winter, the lack of snow due to warm conditions created numerous media headlines and practical problems for the alpine competitions. A statistical model was developed on the premise that February and March temperatures in the Vancouver area could be predicted using an ENSO signal with considerable lead time. This model successfully predicted the warmer-than-normal, lower-snowfall conditions for the Vancouver 2010 Winter Olympics and Paralympics.

Volcanic tremor masks its seismogenic source: Results from a study of noneruptive tremor recorded at Mount St. Helens, Washington

Science.gov (United States)

Denlinger, Roger P.; Moran, Seth C.

2014-01-01

On 2 October 2004, a significant noneruptive tremor episode occurred during the buildup to the 2004–2008 eruption of Mount St. Helens (Washington). This episode was remarkable both because no explosion followed, and because seismicity abruptly stopped following the episode. This sequence motivated us to consider a model for volcanic tremor that does not involve energetic gas release from magma but does involve movement of conduit magma through extension on its way toward the surface. We found that the tremor signal was composed entirely of Love and Rayleigh waves and that its spectral bandwidth increased and decreased with signal amplitude, with broader bandwidth signals containing both higher and lower frequencies. Our modeling results demonstrate that the forces giving rise to this tremor were largely normal to conduit walls, generating hybrid head waves along conduit walls that are coupled to internally reflected waves. Together these form a crucial part of conduit resonance, giving tremor wavefields that are largely a function of waveguide geometry and velocity. We find that the mechanism of tremor generation fundamentally masks the nature of the seismogenic source giving rise to resonance. Thus multiple models can be invoked to explain volcanic tremor, requiring that information from other sources (such as visual observations, geodesy, geology, and gas geochemistry) be used to constrain source models. With concurrent GPS and field data supporting rapid rise of magma, we infer that tremor resulted from drag of nearly solid magma along rough conduit walls as magma was forced toward the surface.

Metro Vancouver air quality management plan : progress report

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-10-15

The Greater Vancouver Regional District (GVRD) developed an air quality management plan (AQMP) in 2005 as a means of addressing air quality issues in the region. The plan required progress reports every 2 years as well as a comprehensive review every 5 years. The AQMP established goals to minimize risk to public health from air pollution, improve visibility, and minimize the region's contributions to global climatic change by reducing emissions; implementing local air quality management programs; and enhancing air quality information and public awareness. The AQMP also included a sustainability framework for GVRD's policies and regulations related to regional growth, service delivery and political leadership. Regional strategies for solid waste and liquid waste management were developed in 2008. The sustainability framework has developed 3 priority goals: (1) to reduce diesel particulates by 75 per cent from Metro Vancouver corporate sources by 2012, (2) to be carbon neutral by 2012 excluding solid waste operations, and (3) to reduce regional GHGs by 15 per cent by 2015, and 33 per cent by 2020. Progress updates on regional planning efforts for the AQMP were presented. The report also outlined trends and performance measures used by the GVRD, and discussed changes in air quality issues and priorities that have occurred since the AQMP was adopted in 2005. 1 tab., 8 figs.

Metro Vancouver air quality management plan : progress report

International Nuclear Information System (INIS)

2008-10-01

The Greater Vancouver Regional District (GVRD) developed an air quality management plan (AQMP) in 2005 as a means of addressing air quality issues in the region. The plan required progress reports every 2 years as well as a comprehensive review every 5 years. The AQMP established goals to minimize risk to public health from air pollution, improve visibility, and minimize the region's contributions to global climatic change by reducing emissions; implementing local air quality management programs; and enhancing air quality information and public awareness. The AQMP also included a sustainability framework for GVRD's policies and regulations related to regional growth, service delivery and political leadership. Regional strategies for solid waste and liquid waste management were developed in 2008. The sustainability framework has developed 3 priority goals: (1) to reduce diesel particulates by 75 per cent from Metro Vancouver corporate sources by 2012, (2) to be carbon neutral by 2012 excluding solid waste operations, and (3) to reduce regional GHGs by 15 per cent by 2015, and 33 per cent by 2020. Progress updates on regional planning efforts for the AQMP were presented. The report also outlined trends and performance measures used by the GVRD, and discussed changes in air quality issues and priorities that have occurred since the AQMP was adopted in 2005. 1 tab., 8 figs

The potential for wind energy meeting electricity needs on Vancouver Island

NARCIS (Netherlands)

Prescott, R.; Kooten, van G.C.; Zhu, H.

2007-01-01

In this paper, an in-depth analysis of power supply and demand on Vancouver Island is used to provide information about the optimal allocation of power across 'generating' sources and to investigate the economics of wind generation and penetrability into the Island grid. The methodology developed

Prostitution in Vancouver: violence and the colonization of First Nations women.

Science.gov (United States)

Farley, Melissa; Lynne, Jacqueline; Cotton, Ann J

2005-06-01

We interviewed 100 women prostituting in Vancouver, Canada. We found an extremely high prevalence of lifetime violence and post-traumatic stress disorder (PTSD). Fifty-two percent of our interviewees were women from Canada's First Nations, a significant overrepresentation in prostitution compared with their representation in Vancouver generally (1.7-7%). Eighty-two percent reported a history of childhood sexual abuse, by an average of four perpetrators. Seventy-two percent reported childhood physical abuse, 90% had been physically assaulted in prostitution, 78% had been raped in prostitution. Seventy-two percent met DSM-IV criteria for PTSD. Ninety-five percent said that they wanted to leave prostitution. Eighty-six percent reported current or past homelessness with housing as one of their most urgent needs. Eighty-two percent expressed a need for treatment for drug or alcohol addictions. Findings are discussed in terms of the legacy of colonialism, the intrinsically traumatizing nature of prostitution and prostitution's violations of basic human rights.

A cost-benefit/cost-effectiveness analysis of an unsanctioned supervised smoking facility in the Downtown Eastside of Vancouver, Canada.

Science.gov (United States)

Jozaghi, Ehsan

2014-11-13

Smoking crack involves the risk of transmitting diseases such as HIV and hepatitis C (HCV). The current study determines whether the formerly unsanctioned supervised smoking facility (SSF)-operated by the grassroot organization, Vancouver Area Network of Drug Users (VANDU) for the last few years-costs less than the costs incurred for health-care services as a direct consequence of not having such a program in Vancouver, Canada. The data pertaining to the attendance at the SSF was gathered in 2012-2013 by VANDU. By relying on this data, a mathematical model was employed to estimate the number of HCV infections prevented by the former facility in Vancouver's Downtown Eastside (DTES). The DTES SSF's benefit-cost ratio was conservatively estimated at 12.1:1 due to its low operating cost. The study used 70% and 90% initial pipe-sharing rates for sensitivity analysis. At 80% sharing rate, the marginal HCV cases prevented were determined to be 55 cases. Moreover, at 80% sharing rate, the marginal cost-effectiveness ratio ranges from $1,705 to $97,203. The results from both the baseline and sensitivity analysis demonstrated that the establishment of the SSF by VANDU on average had annually saved CAD$1.8 million dollars in taxpayer's money. Funding SSFs in Vancouver is an efficient and effective use of financial resources in the public health domain; therefore, Vancouver Coastal Health should actively participate in their establishment in order to reduce HCV and other blood-borne infections such as HIV within the non-injecting drug users.

Evaluation of radon progeny from Mount St. Helens eruptions. Final report

International Nuclear Information System (INIS)

Lepel, E.A.; Olsen, K.B.; Thomas, V.W.; Eichner, F.N.

1982-09-01

A network of twelve monitoring sites around Mount St. Helens was established to evaluate possible short-lived radioactivity in the fallen ash. Seven sites were located near major population centers of Washington and Oregon, and five sites were located within 80 km of the volcano. Each site monitored the radioactivity present by the use of thermoluminescent dosimeters which recorded the total exposure to radioactivity over the exposure period. Eruptions occurring on July 22, August 7, and October 16 to 18, 1980 were monitored. No statistically significant quantities of measurable radon daughters were observed

Mount Baker lahars and debris flows, ancient, modern, and future

Science.gov (United States)

Tucker, David S; Scott, Kevin M.; Grossman, Eric E.; Linneman, Scott

2014-01-01

The Middle Fork Nooksack River drains the southwestern slopes of the active Mount Baker stratovolcano in northwest Washington State. The river enters Bellingham Bay at a growing delta 98 km to the west. Various types of debris flows have descended the river, generated by volcano collapse or eruption (lahars), glacial outburst floods, and moraine landslides. Initial deposition of sediment during debris flows occurs on the order of minutes to a few hours. Long-lasting, down-valley transport of sediment, all the way to the delta, occurs over a period of decades, and affects fish habitat, flood risk, gravel mining, and drinking water.

Source mechanisms of persistent shallow earthquakes during eruptive and non-eruptive periods between 1981 and 2011 at Mount St. Helens, Washington

Science.gov (United States)

Lehto, Heather L.; Roman, Diana C.; Moran, Seth C.

2013-01-01

Shallow seismicity between 0 and 3-km depth has persisted at Mount St. Helens, Washington (MSH) during both eruptive and non-eruptive periods for at least the past thirty years. In this study we investigate the source mechanisms of shallow volcano-tectonic (VT) earthquakes at MSH by calculating high-quality hypocenter locations and fault plane solutions (FPS) for all VT events recorded during two eruptive periods (1981–1986 and 2004–2008) and two non-eruptive periods (1987–2004 and 2008–2011). FPS show a mixture of normal, reverse, and strike-slip faulting during all periods, with a sharp increase in strike-slip faulting observed in 1987–1997 and an increase in normal faulting in 1998–2004. FPS P-axis orientations show a ~ 90° rotation with respect to regional σ1 (N23°E) during 1981–1986 and 2004–2008, bimodal orientations (~ N-S and ~ E-W) during 1987–2004, and bimodal orientations at ~ N-E and ~ S-W from 2008–2011. We interpret these orientations to likely be due to pressurization accompanying the shallow intrusion and subsequent eruption of magma as domes during 1981–1986 and 2004–2008 and the buildup of pore pressure beneath a seismogenic volume (located at 0–1 km) with a smaller component due to the buildup of tectonic forces during 1987–2004 and 2008–2011.

Air quality overview assessment of thermal power generation in Vancouver, BC

International Nuclear Information System (INIS)

Caton, R.B.; Brotherston, A.E.

1992-01-01

B.C. Hydro is preparing a 25 year utilization plan for Burrard Thermal Generating Plant, a 900 MW natural gas fired steam boiler facility near Vancouver. Historical emissions from the plant and ambient air quality in the region were reviewed to place plant operations in context of the technological modifications which have been made over the past 10 years. Environmental effects criteria and regulatory developments which may constrain planning were reviewed and evaluated. Unit emission rates at Burrard have been reduced by 40% since 1989, by extensive combustion modifications, to ca 40 ng/J of NOx. Nevertheless, anticipated regulatory requirements of emissions reductions nationally and in the Vancouver region will necessitate further reductions, or equivalent strategies, over the next ten years. The findings of the Burrard Thermal air quality review are summarized, including historical emissions in the Lower Mainland, transport and transformation of oxidants and acidic deposition, human health impacts, and vegetation impacts. The difficulties that arise in evaluating the imapct of an isolated source of NOx in an urban area are discussed. 30 refs., 5 figs., 6 tabs

The impact of visual air quality on tourism revenues in Greater Vancouver and the Lower Fraser Valley

Energy Technology Data Exchange (ETDEWEB)

McNeill, R. [Environment Canada, Vancouver, BC (Canada); Roberge, A.

2000-07-01

The Greater Vancouver area has been experiencing common episodes of poor visibility as a result of urban and agricultural sources of emissions. A study was conducted to determine the response of tourists in the Vancouver and Lower Fraser Valley Regions to visible air quality and to estimate the potential losses in tourist revenue due to poor visibility episodes. This was accomplished using an interactive survey of tourists in 1999. The results were statistically analyzed to develop visibility response functions. A simple economic model based on the visibility response function was then created to predict losses in tourist revenue. The group of tourists were shown four photographic slides of the Valley and Vancouver area depicting various stages of degradation in visibility. They were asked to rate each slide as either acceptable or unacceptable (if they would not make a return visit). Unacceptability rates for the four camera locations were statistically analyzed. The effect of clouds and the measurable visibility parameter was examined. The model predicts future tourist revenue losses in the amount of $7.45 million for the Greater Vancouver Area and $1.32 million in the Fraser Valley. It was recommended that further research should be conducted with more camera locations to provide a wider variety of viewpoints for assessment. This study can provide direction in setting policies to improve visibility in the region. 25 refs., 20 tabs., 4 figs., 3 appendices.

Variations in community exposure to lahar hazards from multiple volcanoes in Washington State (USA)

Science.gov (United States)

Diefenbach, Angela K.; Wood, Nathan J.; Ewert, John W.

2015-01-01

Understanding how communities are vulnerable to lahar hazards provides critical input for effective design and implementation of volcano hazard preparedness and mitigation strategies. Past vulnerability assessments have focused largely on hazards posed by a single volcano, even though communities and officials in many parts of the world must plan for and contend with hazards associated with multiple volcanoes. To better understand community vulnerability in regions with multiple volcanic threats, we characterize and compare variations in community exposure to lahar hazards associated with five active volcanoes in Washington State, USA—Mount Baker, Glacier Peak, Mount Rainier, Mount Adams and Mount St. Helens—each having the potential to generate catastrophic lahars that could strike communities tens of kilometers downstream. We use geospatial datasets that represent various population indicators (e.g., land cover, residents, employees, tourists) along with mapped lahar-hazard boundaries at each volcano to determine the distributions of populations within communities that occupy lahar-prone areas. We estimate that Washington lahar-hazard zones collectively contain 191,555 residents, 108,719 employees, 433 public venues that attract visitors, and 354 dependent-care facilities that house individuals that will need assistance to evacuate. We find that population exposure varies considerably across the State both in type (e.g., residential, tourist, employee) and distribution of people (e.g., urban to rural). We develop composite lahar-exposure indices to identify communities most at-risk and communities throughout the State who share common issues of vulnerability to lahar-hazards. We find that although lahars are a regional hazard that will impact communities in different ways there are commonalities in community exposure across multiple volcanoes. Results will aid emergency managers, local officials, and the public in educating at-risk populations and developing

Telling our stories: heroin-assisted treatment and SNAP activism in the Downtown Eastside of Vancouver.

Science.gov (United States)

Boyd, Susan; Murray, Dave; MacPherson, Donald

2017-05-18

This article highlights the experiences of a peer-run group, SALOME/NAOMI Association of Patients (SNAP), that meets weekly in the Downtown Eastside of Vancouver, British Columbia, Canada. SNAP is a unique independent peer- run drug user group that formed in 2011 following Canada's first heroin-assisted treatment trial (HAT), North America Opiate Medication Initiative (NAOMI). SNAP's members are now made up of former research participants who participated in two heroin-assisted trials in Vancouver. This article highlights SNAP members' experiences as research subjects in Canada's second clinical trial conducted in Vancouver, Study to Assess Longer-term Opioid Medication Effectiveness (SALOME), that began recruitment of research participants in 2011. This paper draws on one brainstorming session, three focus groups, and field notes, with the SALOME/NAOMI Association of Patients (SNAP) in late 2013 about their experiences as research subjects in Canada's second clinical trial, SALOME in the DTES of Vancouver, and fieldwork from a 6-year period (March 2011 to February 2017) with SNAP members. SNAP's research draws on research principles developed by drug user groups and critical methodological frameworks on community-based research for social justice. The results illuminate how participating in the SALOME clinical trial impacted the lives of SNAP members. In addition, the findings reveal how SNAP member's advocacy for HAT impacts the group in positive ways. Seven major themes emerged from the analysis of the brainstorming and focus groups: life prior to SALOME, the clinic setting and routine, stability, 6-month transition, support, exiting the trial and ethics, and collective action, including their participation in a constitutional challenge in the Supreme Court of BC to continue receiving HAT once the SALOME trial ended. HAT benefits SNAP members. They argue that permanent HAT programs should be established in Canada because they are an effective harm reduction

PV module mounting method and mounting assembly

Science.gov (United States)

Lenox, Carl J.S.; Johnson, Kurt M.

2013-04-23

A method for mounting PV modules to a deck includes selecting PV module layout pattern so that adjacent PV module edges are spaced apart. PV mounting and support assemblies are secured to the deck according to the layout pattern using fasteners extending into the deck. The PV modules are placed on the PV mounting and support assemblies. Retaining elements are located over and secured against the upper peripheral edge surfaces of the PV modules so to secure them to the deck with the peripheral edges of the PV modules spaced apart from the deck. In some examples a PV module mounting assembly, for use on a shingled deck, comprises flashing, a base mountable on the flashing, a deck-penetrating fastener engageable with the base and securable to the deck so to secure the flashing and the base to the shingled deck, and PV module mounting hardware securable to the base.

VP Structure of Mount St. Helens, Washington, USA, imaged with local earthquake tomography

Science.gov (United States)

Waite, G.P.; Moran, S.C.

2009-01-01

We present a new P-wave velocity model for Mount St. Helens using local earthquake data recorded by the Pacific Northwest Seismograph Stations and Cascades Volcano Observatory since the 18 May 1980 eruption. These data were augmented with records from a dense array of 19 temporary stations deployed during the second half of 2005. Because the distribution of earthquakes in the study area is concentrated beneath the volcano and within two nearly linear trends, we used a graded inversion scheme to compute a coarse-grid model that focused on the regional structure, followed by a fine-grid inversion to improve spatial resolution directly beneath the volcanic edifice. The coarse-grid model results are largely consistent with earlier geophysical studies of the area; we find high-velocity anomalies NW and NE of the edifice that correspond with igneous intrusions and a prominent low-velocity zone NNW of the edifice that corresponds with the linear zone of high seismicity known as the St. Helens Seismic Zone. This low-velocity zone may continue past Mount St. Helens to the south at depths below 5??km. Directly beneath the edifice, the fine-grid model images a low-velocity zone between about 2 and 3.5??km below sea level that may correspond to a shallow magma storage zone. And although the model resolution is poor below about 6??km, we found low velocities that correspond with the aseismic zone between about 5.5 and 8??km that has previously been modeled as the location of a large magma storage volume. ?? 2009 Elsevier B.V.

Rockslide-debris avalanche of May 18, 1980, Mount St. Helens Volcano, Washington

Science.gov (United States)

Glicken, Harry

1996-01-01

This report provides a detailed picture of the rockslide-debris avalanche of the May 18, 1980, eruption of Mount St. Helens volcano. It provides a characterization of the deposit, a reinterpretation of the details of the first minutes of the eruption of May 18, and insight into the transport mechanism of the mass movement. Details of the rockslide event, as revealed by eyewitness photographs, are correlated with features of the deposit. The photographs show three slide blocks in the rockslide movement. Slide block I was triggered by a magnitude 5.1 earthquake at 8:32 a.m. Pacific Daylight Time (P.D.T.). An exploding cryptodome burst through slide block II to produce the 'blast surge.' Slide block III consisted of many discrete failures that were carried out in continuing pyroclastic currents generated from the exploding cryptodome. The cryptodome continued to depressurize after slide block III, producing a blast deposit that rests on top of the debris-avalanche deposit. The hummocky 2.5 cubic kilometer debris-avalanche deposit consists of block facies (pieces of the pre-eruption Mount St. Helens transported relatively intact) and matrix facies (a mixture of rocks from the old mountain and cryptodome dacite). Block facies is divided into five lithologic units. Matrix facies was derived from the explosively generated current of slide block III as well as from disaggregation and mixing of debris-avalanche blocks. The mean density of the old cone was measured to be abut 20 percent greater than the mean density of the avalanche deposit. Density in the deposit does not decrease with distance which suggests that debris-avalanche blocks were dilated at the mountain, rather than during transport. Various grain-size parameters that show that clast size converges about a mean with distance suggest mixing during transport. The debris-avalanche flow can be considered a grain flow, where particles -- either debris-avalanche blocks or the clasts within the blocks -- collided and

Magma at depth: A retrospective analysis of the 1975 unrest at Mount Baker, Washington, USA

Science.gov (United States)

Crider, Juliet G.; Frank, David; Malone, Stephen D.; Poland, Michael P.; Werner, Cynthia; Caplan-Auerbach, Jacqueline

2011-01-01

Mount Baker volcano displayed a short interval of seismically-quiescent thermal unrest in 1975, with high emissions of magmatic gas that slowly waned during the following three decades. The area of snow-free ground in the active crater has not returned to pre-unrest levels, and fumarole gas geochemistry shows a decreasing magmatic signature over that same interval. A relative microgravity survey revealed a substantial gravity increase in the ~30 years since the unrest, while deformation measurements suggest slight deflation of the edifice between 1981-83 and 2006-07. The volcano remains seismically quiet with regard to impulsive volcano-tectonic events, but experiences shallow (10 km) long-period earthquakes. Reviewing the observations from the 1975 unrest in combination with geophysical and geochemical data collected in the decades that followed, we infer that elevated gas and thermal emissions at Mount Baker in 1975 resulted from magmatic activity beneath the volcano: either the emplacement of magma at mid-crustal levels, or opening of a conduit to a deep existing source of magmatic volatiles. Decadal-timescale, multi-parameter observations were essential to this assessment of magmatic activity.

Colonization and Community: the Vancouver Island coalfield and the making of the British Columbian working class

Energy Technology Data Exchange (ETDEWEB)

John Douglas Belshaw [University College of the Cariboo, Kamloops, BC (Canada). Department of Philosophy, History, and Politics

2002-04-01

In the nineteenth century coal-miners imported from Europe, Asia, and eastern North America burrowed beneath the Vancouver Island towns of Nanaimo, Wellington, and Cumberland. The book looks at British Columbia's first working class, the men, women, and children beneath and beyond the pit-head. Beginning with an exploration of emigrant expectations and ambitions, it investigates working conditions, household wages, racism, industrial organization, gender, schooling, leisure, community building, and the fluid identity of the British mining colony, the archetypal west coast proletariat. By connecting the story of Vancouver Island to the larger story of Victorian industrialization, the author delineates what was distinctive and what was common about the lot of the settler society.

Adventure Education and the Acculturation of First-Generation Chinese Canadians in Vancouver, Canada

Science.gov (United States)

Lo, Simon; Gidlow, Bob; Cushman, Grant

2014-01-01

This article reports on research that demonstrates how parents in first-generation Chinese families in Vancouver, Canada, most of them from Hong Kong, control their children's involvement in local adventure education (AE) programs and in so doing minimize the likelihood of intergenerational culture conflict involving those children. The research…

Immigrants as Active Citizens: Exploring the Volunteering Experience of Chinese Immigrants in Vancouver

Science.gov (United States)

Guo, Shibao

2014-01-01

Despite the fact that immigration has played an important role in transforming Canada into an ethno-culturally diverse and economically prosperous nation, immigrants themselves are often criticised as passive citizens. This study attempts to deconstruct this myth by investigating the volunteering experiences of Chinese immigrants in Vancouver. The…

THE PROPOSED NATIONAL ARBORETUM AT WASHINGTON.

Science.gov (United States)

Coville, F V

1925-12-25

Nature. The proposed national arboretum at Washington would contain a permanent living collection of trees and other outdoor plants for purposes of scientific research and education. It would include the trees, shrubs, and perennials used in forestry and horticulture, and the wild relatives of these plants. It would be a bureau of standards for horticulture. It would contain a water garden and a wildrice preserve, and it would serve incidentally as a bird sanctuary. Economic value. The arboretum would make the work of the Department of Agriculture more valuable to the country in many ways, but especially through plant breeding. The development of faster-growing timber trees, improved fruits, and disease-resistant plants generally, through the facilities afforded by the arboretum, would increase profoundly the agricultural wealth and welfare of the United States. Location. The Mount Hamilton and Hickey Hill tracts in the District of Columbia, together with the Anacostia River flats above Benning Bridge, constitute an admirable site for the arboretum, convenient in location and with a great variety of soils. Cost. About 400 acres of the proposed site is already owned by the government. It consists of marsh land, about to be drained by army engineers. The Mount Hamilton and Hickey Hill area, 408 acres, privately owned, was reported by the assessor in January, 1925, to be valued at $343,048, distributed among thirty owners. Maintenance. If the purchase of the Mount Hamilton and Hickey Hill tracts in the fiscal year 1927 is authorized, it is estimated that the cost of maintenance of the arboretum for the first three years would be as follows: 1927. Nothing 1928. $25,000 1929. $50,000.

Analysis of potential debris flow source areas on Mount Shasta, California, by using airborne and satellite remote sensing data

Science.gov (United States)

Crowley, J.K.; Hubbard, B.E.; Mars, J.C.

2003-01-01

Remote sensing data from NASA's Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) and the first spaceborne imaging spectrometer, Hyperion, show hydrothermally altered rocks mainly composed of natroalunite, kaolinite, cristobalite, and gypsum on both the Mount Shasta and Shastina cones. Field observations indicate that much of the visible altered rock consists of talus material derived from fractured rock zones within and adjacent to dacitic domes and nearby lava flows. Digital elevation data were utilized to distinguish steeply sloping altered bedrock from more gently sloping talus materials. Volume modeling based on the imagery and digital elevation data indicate that Mount Shasta drainage systems contain moderate volumes of altered rock, a result that is consistent with Mount Shasta's Holocene record of mostly small to moderate debris flows. Similar modeling for selected areas at Mount Rainier and Mount Adams, Washington, indicates larger altered rock volumes consistent with the occurrence of much larger Holocene debris flows at those volcanoes. The availability of digital elevation and spectral data from spaceborne sensors, such as Hyperion and the Advanced Spaceborne Thermal Emission and Reflectance Radiometer (ASTER), greatly expands opportunities for studying potential debris flow source characteristics at stratovolcanoes around the world. ?? 2003 Elsevier Inc. All rights reserved.

Height growth and site index curves for western white pine in the Cascade Range of Washington and Oregon.

Science.gov (United States)

Robert O. Curtis; Nancy M. Diaz; Gary W. Clendenen

1990-01-01

Height growth and site index curves were constructed from stem analyses of mature western white pine (Pinus monticola Dougl. ex D. Don) growing in high-elevation forests of the Cascade Range in the Mount Hood and Gifford Pinchot National Forests of Oregon and Washington, respectively. Alternate systems using reference ages for site index of 50 and...

Going Social at Vancouver Public Library: What the Virtual Branch Did Next

Science.gov (United States)

Cahill, Kay

2011-01-01

Purpose: The purpose of this paper is to follow up on the 2009 publication "Building a virtual branch at Vancouver Public Library (VPL) using Web 2.0 tools" and to explore the work that VPL has been doing in the social media space over the past two years. Design/methodology/approach: Following the launch of its new web site in 2008,…

Photovoltaic mounting/demounting unit

DEFF Research Database (Denmark)

2014-01-01

The present invention relates to a photovoltaic arrangement comprising a photovoltaic assembly comprising a support structure defining a mounting surface onto which a photovoltaic module is detachably mounted; and a mounting/demounting unit comprising at least one mounting/demounting apparatus...... which when the mounting/demounting unit is moved along the mounting surface, causes the photovoltaic module to be mounted or demounted to the support structure; wherein the photovoltaic module comprises a carrier foil and wherein a total thickness of the photo voltaic module is below 500 muiotaeta....... The present invention further relates to an associated method for mounting/demounting photovoltaic modules....

Building a Virtual Branch at Vancouver Public Library Using Web 2.0 Tools

Science.gov (United States)

Cahill, Kay

2009-01-01

Purpose: The purpose of this paper is to demonstrate the work undertaken by Vancouver Public Library (VPL) in an effort to convert its website into a true virtual branch, both through the functionality of the website itself and by extending its web presence on to external social networking sites. Design/methodology/approach: VPL worked with its…

Vancouver Cyclotron Conference

International Nuclear Information System (INIS)

Clark, David J.

1993-01-01

Although no longer on the high energy frontier, the cyclotron field is still a major scientific growth area. Its progress is highlighted at the international conference on cyclotron design, development and utilization held at intervals of about three years, under the auspices of the International Union of Pure and Applied Physics (IUPAP). Vancouver, surrounded by mountains, water and some cyclotrons, provided a pleasant setting for the 13th Conference, held last summer. With over 200 cyclotrons in operation around the world, the attendance, 241 delegates and 26 industrial exhibitors, was a near record, reflecting the flourishing state of the field. The early sessions covered the initial operation of new or upgraded cyclotron facilities. Major facilities completed since the previous Conference in Berlin in May 1989 included the 400 MeV ring cyclotron at Osaka, the U400M cyclotron at Dubna which will be coupled to the U400 to give 20 MeV nucléon uranium beams, the 130 MeV cyclotron at Jyvaskyla (in Finland, the furthest north!), the 110 MeV JAERI machine in Japan, and the 65 MeV proton therapy cyclotron in Nice. Among the facility upgrades were the KFA cyclotron at Julich which will inject the 2.5 GeV storage ring COSY, and the addition of an FM mode to the K=200 CW mode at Uppsala to give protons up to 180 MeV. The impressive current of 1.5 mA at 72 MeV obtained from the PSI Injector II will soon be injected into the 590 MeV ring

ZEUS contributions to the Real-Time 93 conference, Vancouver, Canada

International Nuclear Information System (INIS)

1993-07-01

This is a collection of the eight contributions of the ZEUS Data Acquisition group, presented at the Eighth Conference on Real-Time Computer Applications in Nuclear, Particle and Plasma Physics, Vancouver, Canada, June 8-11, 1993. This note describes the major parts of the ZEUS Data Acquisition system and the experience gained since the first HERA running in April 1992. Note that the papers are appended in the order of recommended reading, which does not reflect the order of importance. The presenters for the papers are listed in the following. (orig.)

Embracing a New Understanding of the City: The Museum of Vancouver's Vision in Action

Science.gov (United States)

Gosselin, Viviane

2013-01-01

The Museum of Vancouver recently undertook a major rethinking of its role in the city. New interplays are being proposed between emerging conceptions of urbanity and civic participation, and the museum's collection and function as facilitator and advocate. This short paper provides a brief overview of the museum's recent transformation, situates…

Proximal ecological effects of the 1980 eruptions of Mount St. Helens

Science.gov (United States)

Swanson, F. J.

1988-01-01

The diversity of ecosystems and volcanic processes involved in the 1980 eruptions of Mount St. Helens, southwest Washington, provide an excellent setting for examining effects of volcanic events on ecosystems. These eruptions included a lateral blast, debris avalanche, mudflows, pyroclastic flows, and airfall tephra. Affected ecosystems within 30 km of the vent were lakes, streams, upland and riparian forest, and meadows. Ecological disturbances imposed by the Mount St. Helens events were predominantly physical, rather than climatic or chemical which are the dominant classes of disturbances considered in analysis of global catastrophes. Analysis of ecosystem response to disturbance should be based on consideration of composition and structure of the predisturbance system in terms that represent potential survivability of organisms, mechanisms in the primary disturbance, initial survivors, secondary disturbances arising from the primary disturbance and the biological responses to secondary disturbances, invasion of the site by new propagules, interactions among secondary disturbance processes and surviving and invading organisms. Predicting ecosystem response to disturbance is enchanced by considering the mechanisms of disturbance rather than type of disturbance. In the 1980 Mount St. Helens events, the disturbance types, involved primarily the mechanisms of sedimentation, heating, and shear stress. Each disturbance type involved one or more mechanisms. Ecosystem response varied greatly across the landscape. Analysis of ecosystem response to disturbance, regardless of type, should include detailed consideration of the properties of individual species, primary and secondary disturbance mechanisms, and their distributions across landscapes.

Photovoltaic module mounting system

Science.gov (United States)

Miros, Robert H. J. [Fairfax, CA; Mittan, Margaret Birmingham [Oakland, CA; Seery, Martin N [San Rafael, CA; Holland, Rodney H [Novato, CA

2012-04-17

A solar array mounting system having unique installation, load distribution, and grounding features, and which is adaptable for mounting solar panels having no external frame. The solar array mounting system includes flexible, pedestal-style feet and structural links connected in a grid formation on the mounting surface. The photovoltaic modules are secured in place via the use of attachment clamps that grip the edge of the typically glass substrate. The panel mounting clamps are then held in place by tilt brackets and/or mid-link brackets that provide fixation for the clamps and align the solar panels at a tilt to the horizontal mounting surface. The tilt brackets are held in place atop the flexible feet and connected link members thus creating a complete mounting structure.

Magnetic core mounting system

Science.gov (United States)

Ronning, Jeffrey J.

2002-01-01

A mounting apparatus for an electromagnetic device such as a transformer of inductor includes a generally planar metallic plate as a first heat sink, and a metallic mounting cup as a second heat sink. The mounting cup includes a cavity configured to receive the electromagnetic device, the cavity being defined by a base, and an axially-extending annular sidewall extending from the base to a flange portion of the mounting cup. The mounting cup includes first and second passages for allowing the leads of first and second windings of the electromagnetic device to be routed out of the cavity. The cavity is filled with a polyurethane potting resin, and the mounting cup, including the potted electromagnetic device, is mounted to the plate heat sink using fasteners. The mounting cup, which surrounds the electromagnetic device, in combination with the potting resin provides improved thermal transfer to the plate heat sink, as well as providing resistance to vibration and shocks.

Optoelectronic Mounting Structure

Science.gov (United States)

Anderson, Gene R.; Armendariz, Marcelino G.; Baca, Johnny R. F.; Bryan, Robert P.; Carson, Richard F.; Chu, Dahwey; Duckett, III, Edwin B.; McCormick, Frederick B.; Peterson, David W.; Peterson, Gary D.; Reber, Cathleen A.; Reysen, Bill H.

2004-10-05

An optoelectronic mounting structure is provided that may be used in conjunction with an optical transmitter, receiver or transceiver module. The mounting structure may be a flexible printed circuit board. Thermal vias or heat pipes in the head region may transmit heat from the mounting structure to the heat spreader. The heat spreader may provide mechanical rigidity or stiffness to the heat region. In another embodiment, an electrical contact and ground plane may pass along a surface of the head region so as to provide an electrical contact path to the optoelectronic devices and limit electromagnetic interference. In yet another embodiment, a window may be formed in the head region of the mounting structure so as to provide access to the heat spreader. Optoelectronic devices may be adapted to the heat spreader in such a manner that the devices are accessible through the window in the mounting structure.

The Geography of School Choice in a City with Growing Inequality: The Case of Vancouver

Science.gov (United States)

Yoon, Ee-Seul; Lubienski, Christopher; Lee, Jin

2018-01-01

This analysis aims to measure the impact of school choice policy on secondary school students' enrolment patterns within the social geography of Vancouver, an increasingly polarized global city. The rationale for the study is to examine the impact of "education market" reforms on the socio-economic composition of schools in a Canadian…

Liner mounting assembly

Science.gov (United States)

Halila, Ely E. (Inventor)

1994-01-01

A mounting assembly includes an annular supporting flange disposed coaxially about a centerline axis which has a plurality of circumferentially spaced apart supporting holes therethrough. An annular liner is disposed coaxially with the supporting flange and includes a plurality of circumferentially spaced apart mounting holes aligned with respective ones of the supporting holes. Each of a plurality of mounting pins includes a proximal end fixedly joined to the supporting flange through a respective one of the supporting holes, and a distal end disposed through a respective one of the liner mounting holes for supporting the liner to the supporting flange while unrestrained differential thermal movement of the liner relative to the supporting flange.

Vancouver winters: Environmental influences on inpatient adult orthopaedic trauma demographics

International Nuclear Information System (INIS)

Noordin, S.; Masri, B. A.

2014-01-01

Objective: To compare the pattern of adult inpatient orthopaedic injuries admitted at three Vancouver hospitals following one of the worst winter snowstorms in the region with the preceding control winter period. Methods: The surveillance study was conducted at the University of British Columbia, Vancouver, Canada, 2007 to 2010. Inpatient adult admissions for orthopaedic injuries at three hospitals were recorded, including age, gender, anatomic location of injury, type of fracture (open or closed), fixation method (internal versus external fixation), and length of acute care hospital stay. Comparisons between admissions during this weather pattern and admission during a previous winter with minimal snow were made. SPSS 19 was used for statistical analysis. Results: Of the 511 patients admitted under Orthopaedic trauma service during the significant winter snowstorms of December 2008 - January 2009, 100 (19.6%) (CI: 16.2%-23.2%) were due to ice and snow, whereas in the preceding mild winter only 18 of 415 (4.3%) (CI: 2.5%-6.8%) cases were related to snow (p<0.05). Ankle and wrist fractures were the most frequent injuries during the index snow storm period (p<0.05). At all the three institutions, 97 (96.5%) fractures were closed during the snowstorm as opposed to 17 (95%) during the control winter period. Internal fixation in 06 (89%) fractures as opposed to external fixation in 12 (11%) patients was the predominant mode of fixation across the board during both time periods. Conclusion: The study demonstrated a significantly higher inpatient orthopaedic trauma volume during the snowstorm more rigorous prospective studies need to be designed to gain further insight to solving these problems from a public health perspective. (author)

The conscious city II: traffic congestion and the tipping point in greater Vancouver

OpenAIRE

Holt, Rebecca

2007-01-01

The Conscious City II explores how broad, long-term change toward sustainability in cities can be fostered, nurtured and facilitated. Using a qualitative, mixed-method approach, this research adapts a model from Malcolm Gladwell’s Tipping Point framework to explore how social consciousness can be mobilized to achieve change toward sustainability through an analysis of traffic congestion in Greater Vancouver. The results demonstrate the important influence of leadership, context and message on...

Urban policy engagement with social sustainability in metro Vancouver.

Science.gov (United States)

Holden, Meg

2012-01-01

This article presents an analysis of social sustainability in comparative theoretical context and as a challenge to the post-political interpretation of sustainability in policy practice at the urban and regional scales. Metro Vancouver provides a case study for improving our understanding of the meaning of social sustainability as a framework for social policy in that it is among the handful of cities around the world currently working to define and enact social sustainability in governance terms. Results of this participant research provide evidence that some cities are politically engaging alternative development pathways using the concept of social sustainability. For sustainable development to retain its promise as an alternative policy framework for cities, social sustainability must be at the forefront.

Zircon reveals protracted magma storage and recycling beneath Mount St. Helens

Science.gov (United States)

Claiborne, L.L.; Miller, C.F.; Flanagan, D.M.; Clynne, M.A.; Wooden, J.L.

2010-01-01

Current data and models for Mount St. Helens volcano (Washington, United States) suggest relatively rapid transport from magma genesis to eruption, with no evidence for protracted storage or recycling of magmas. However, we show here that complex zircon age populations extending back hundreds of thousands of years from eruption age indicate that magmas regularly stall in the crust, cool and crystallize beneath the volcano, and are then rejuvenated and incorporated by hotter, young magmas on their way to the surface. Estimated dissolution times suggest that entrained zircon generally resided in rejuvenating magmas for no more than about a century. Zircon elemental compositions reflect the increasing influence of mafic input into the system through time, recording growth from hotter, less evolved magmas tens of thousands of years prior to the appearance of mafic magmas at the surface, or changes in whole-rock geochemistry and petrology, and providing a new, time-correlated record of this evolution independent of the eruption history. Zircon data thus reveal the history of the hidden, long-lived intrusive portion of the Mount St. Helens system, where melt and crystals are stored for as long as hundreds of thousands of years and interact with fresh influxes of magmas that traverse the intrusive reservoir before erupting. ?? 2010 Geological Society of America.

Geologic map of the Simcoe Mountains Volcanic Field, main central segment, Yakama Nation, Washington

Science.gov (United States)

Hildreth, Wes; Fierstein, Judy

2015-01-01

Mountainous parts of the Yakama Nation lands in south-central Washington are mostly covered by basaltic lava flows and cinder cones that make up the Simcoe Mountains volcanic field. The accompanying geologic map of the central part of the volcanic field has been produced by the U.S. Geological Survey (USGS) on behalf of the Water Resources Program of the Yakama Nation. The volcanic terrain stretches continuously from Mount Adams eastward as far as Satus Pass and Mill Creek Guard Station. Most of the many hills and buttes are volcanic cones where cinders and spatter piled up around erupting vents while lava flows spread downslope. All of these small volcanoes are now extinct, and, even during their active lifetimes, most of them erupted for no more than a few years. On the Yakama Nation lands, the only large long-lived volcano capable of erupting again in the future is Mount Adams, on the western boundary.

Forest insect and disease conditions, Vancouver forest region, 1987. Annual publication

Energy Technology Data Exchange (ETDEWEB)

Humphreys, N; Ferris, R L

1988-01-01

The Forest Insect and Disease Survey (FIDS) is a nation-wide network within Forestry Canada with the responsibility of producing an overview of forest pest conditions and their implications; maintaining records and surveys to support quarantine and facilitate predictions; supporting forestry research with records, insect collections and herbaria; providing advice on forest insect and disease conditions; developing and testing survey techniques; and conducting related biological studies. This report outlines the status of forest pest conditions in the Vancouver Forest Region, and forecasts population trends of some potentially damaging pests. Pests are listed by host in order of importance.

33 CFR 165.1314 - Safety Zone; Fort Vancouver Fireworks Display, Columbia River, Vancouver, Washington.

Science.gov (United States)

2010-07-01

... highway bridge to Hayden Island, Oregon at latitude 45°36″ 51.5′ N, longitude 122°40″ 39′ W; thence east along Hayden Island to latitude 45°36″ 36′ N, longitude 122°39″ 48′ W (not to include Hayden Bay...

A Search for Decolonizing Place-Based Pedagogies: An Exploration of Unheard Histories in Kitsilano Vancouver, B.C.

Science.gov (United States)

Henry, Elizabeth Ruth

2014-01-01

This paper explores the ways that place-based pedagogies can facilitate dialogue on colonization, or some of the "dark matters" of environmental education, specifically by engaging non-Indigenous adults in decolonizing dialogues. I share findings from an action research project with Kitsilano Neighbourhood House in Vancouver, British…

First hvdc underwater transmission links mainland and Vancouver

Energy Technology Data Exchange (ETDEWEB)

1967-06-01

Delicate and complex equipment for North America's first hvdc underwater transmission line is being installed. The power link will connect British Columbia Hydro and power authority's switchyards on the mainland near Ladner with the western terminus of the transmission scheme at Duncan on Vancouver Island, a distance of 42 miles. Nearly 19 miles of the transmission will be underwater, between Tsawwassen and Galiano Island, and between Parker and Saltspring Islands. The remaining distance will be spanned by a conventional aerial conductor. The submarine conductor cable will be approximately 3-1/2 inches in diameter and its copper core will be sheathed in lead and armored with a ring of steel wire. The cable, which is being manufactured in Calais, France, and coiled in a planned sequence aboard the cable laying vessel, Marcel Bayard, will be placed across the Gulf of Georgia in the spring of 1968.

Chronology and pyroclastic stratigraphy of the May 18, 1980, eruption of Mount St. Helens, Washington

Science.gov (United States)

Criswell, C. William

1987-01-01

The eruption of Mount St. Helens on May 18, 1980 can be subdivided into six phases: the paroxysmal phase I, the early Plinian phase II, the early ash flow phase III, the climactic phase IV, the late ash flow phase V, and phase VI, the activity of which consisted of a low-energy ash plume. These phases are correlated with stratigraphic subunits of ash-fall tephra and pyroclastic flow deposits. Sustained vertical discharge of phase II produced evolved dacite with high S/Cl ratios. Ash flow activity of phase III is attributed to decreases in gas content, indicated by reduced S/Cl ratios and increased clast density of the less evolved gray pumice. Climactic events are attributed to vent clearing and exhaustion of the evolved dacite.

Shoulder-Mounted Robot for MRI-guided arthrography: Accuracy and mounting study.

Science.gov (United States)

Monfaredi, R; Wilson, E; Sze, R; Sharma, K; Azizi, B; Iordachita, I; Cleary, K

2015-08-01

A new version of our compact and lightweight patient-mounted MRI-compatible 4 degree-of-freedom (DOF) robot for MRI-guided arthrography procedures is introduced. This robot could convert the traditional two-stage arthrography procedure (fluoroscopy-guided needle insertion followed by a diagnostic MRI scan) to a one-stage procedure, all in the MRI suite. The results of a recent accuracy study are reported. A new mounting technique is proposed and the mounting stability is investigated using optical and electromagnetic tracking on an anthropomorphic phantom. Five volunteer subjects including 2 radiologists were asked to conduct needle insertion in 4 different random positions and orientations within the robot's workspace and the displacement of the base of the robot was investigated during robot motion and needle insertion. Experimental results show that the proposed mounting method is stable and promising for clinical application.

Database for geologic maps of pyroclastic-flow and related deposits of the 1980 eruptions of Mount St. Helens, Washington

Science.gov (United States)

Furze, Andrew J.; Bard, Joseph A.; Robinson, Joel; Ramsey, David W.; Kuntz, Mel A.; Rowley, Peter D.; MacLeod, Norman S.

2017-10-31

This publication releases digital versions of the geologic maps in U.S. Geological Survey Miscellaneous Investigations Map 1950 (USGS I-1950), “Geologic maps of pyroclastic-flow and related deposits of the 1980 eruptions of Mount St. Helens, Washington” (Kuntz, Rowley, and MacLeod, 1990) (https://pubs.er.usgs.gov/publication/i1950). The 1980 Mount St. Helens eruptions on May 18, May 25, June 12, July 22, August 7, and October 16–18 produced pyroclastic-flow and related deposits. The distribution and morphology of these deposits, as determined from extensive field studies and examination of vertical aerial photographs, are shown on four maps in I-1950 (maps A–D) on two map sheets. Map A shows the May 18, May 25, and June 12 deposits; map B shows the July 22 deposits; map C shows the August 7 deposits; and map D shows the October 16–18 deposits. No digital geospatial versions of the geologic data were made available at the time of publication of the original maps. This data release consists of attributed vector features, data tables, and the cropped and georeferenced scans from which the features were digitized, in order to enable visualization and analysis of these data in GIS software. This data release enables users to digitally re-create the maps and description of map units of USGS I-1950; map sheet 1 includes text sections (Introduction, Physiography of Mount St. Helens at the time of the 1980 eruptions, Processes of the 1980 eruptions, Deposits of the 1980 eruptions, Limitations of the maps, Preparation of the maps, and References cited) and associated tables and figures that are not included in this data release.

EnviroAtlas - Portland, OR - Meter-Scale Urban Land Cover (MULC) Data (2012)

Data.gov (United States)

U.S. Environmental Protection Agency — The EnviroAtlas Portland, OR Meter-Scale Urban Land Cover (MULC) dataset includes data for the Portland metropolitan area plus the city of Vancouver, Washington and...

Interobserver and intraobserver reliability and validity of the Vancouver classification system of periprosthetic femoral fractures after hip arthroplasty.

LENUS (Irish Health Repository)

Naqvi, Gohar A

2012-06-01

The Vancouver classification system of periprosthetic fractures has been revalidated in this study, using the radiographs of 45 patients. Three consultants and 3 trainees reviewed the radiographs independently, on 2 separate occasions, at least 2 weeks apart. Interobserver and intraobserver agreement and validity were analyzed, using weighted κ statistics. The mean κ value for interobserver agreement was found to be 0.69 (0.63-0.72) for consultants and 0.61 (0.56-0.65) for the trainees, both representing substantial agreement. Intraobserver κ values ranged from 0.74 to 0.90, showing substantial agreement. Validity analysis of 37 type B cases revealed 81% agreement within B1, B2, and B3 subgroups with a κ value of 0.68 (substantial agreement). This study has reconfirmed the reliability and validity of the Vancouver classification while it also emphasizes the intraoperative assessment of implant stability.

78 FR 15053 - Simpson Lumber Company, LLC, Shelton, Washington; Simpson Lumber Company, LLC, Tacoma, Washington...

Science.gov (United States)

2013-03-08

...,372B] Simpson Lumber Company, LLC, Shelton, Washington; Simpson Lumber Company, LLC, Tacoma, Washington; Simpson Lumber Company, LLC, Longview, Washington; Notice of Revised Determination on Reconsideration On... Reconsideration for the workers and former workers of Simpson Lumber Company, LLC, Shelton, Washington (TA-W-81...

Analysis of adjusting effects of mounting force on frequency conversion of mounted nonlinear optics.

Science.gov (United States)

Su, Ruifeng; Liu, Haitao; Liang, Yingchun; Lu, Lihua

2014-01-10

Motivated by the need to increase the second harmonic generation (SHG) efficiency of nonlinear optics with large apertures, a novel mounting configuration with active adjusting function on the SHG efficiency is proposed and mechanically and optically studied. The adjusting effects of the mounting force on the distortion and stress are analyzed by the finite element methods (FEM), as well as the contribution of the distortion and stress to the change in phase mismatch, and the SHG efficiency are theoretically stated. Further on, the SHG efficiency is calculated as a function of the mounting force. The changing trends of the distortion, stress, and the SHG efficiency with the varying mounting force are obtained, and the optimal ones are figured out. Moreover, the mechanism of the occurrence of the optimal values is studied and the adjusting strategy is put forward. Numerical results show the robust adjustment of the mounting force, as well as the effectiveness of the mounting configuration, in increasing the SHG efficiency.

Water-quality effects on Baker Lake of recent volcanic activity at Mount Baker, Washington

Science.gov (United States)

Bortleson, Gilbert Carl; Wilson, Reed T.; Foxworthy, B.L.

1976-01-01

Increased volcanic activity on Mount Baker, which began in March 1975, represents the greatest known activity of a Cascade Range volcano since eruptions at Lassen Peak, Calif. during 1914-17. Emissions of dust and increased emanations of steam, other gases, and heat from the Sherman Crater area of the mountain focused attention on the possibility of hazardous events, including lava flows, pyroclastic eruptions, avalanches, and mudflows. However, the greatest undesirable natural results that have been observed after one year of the increased activity are an increase in local atmospheric pollution and a decrease in the quality of some local water resources, including Baker Lake. Baker Lake, a hydropower reservoir behind Upper Baker Dam, supports a valuable fishery resource and also is used for recreation. The lake's feedwater is from Baker River and many smaller streams, some of which, like Boulder Creek, drain parts of Mount Baker. Boulder Creek receives water from Sherman Crater, and its channel is a likely route for avalanches or mudflows that might originate in the crater area. Boulder Creek drains only about 5 percent of the total drainage area of Baker Lake, but during 1975 carried sizeable but variable loads of acid and dissolved minerals into the lake. Sulfurous gases and the fumarole dust from Sherman Crater are the main sources for these materials, which are brought into upper Boulder Creek by meltwater from the crater. In September 1973, before the increased volcanic activity, Boulder Creek near the lake had a pH of 6.0-6.6; after the increase the pH ranged as low as about 3.5. Most nearby streams had pH values near 7. On April 29, in Boulder Creek the dissolved sulfate concentration was 6 to 29 times greater than in nearby creeks or in Baker River; total iron was 18-53 times greater than in nearby creeks; and other major dissolved constituents generally 2 to 7 times greater than in the other streams. The short-term effects on Baker Lake of the acidic

Toward a cardiovascular pathology training report on the forum held in Vancouver, March 6, 2004, Society for Cardiovascular Pathology

NARCIS (Netherlands)

Thiene, Gaetano; Becker, Anton E.; Buja, L. Maximilian; Fallon, John T.; McManus, Bruce M.; Schoen, Frederick J.; Winters, Gayle L.

2005-01-01

Cardiovascular pathology is a subspecialty of anatomic pathology that requires both clinical education and expertise in contemporary physiopathology. The Society for Cardiovascular Pathology sponsored a special workshop within the frame of the USCAP Annual Meeting, held in Vancouver, March 6-12,

Workplace violence among female sex workers who use drugs in Vancouver, Canada: does client-targeted policing increase safety?

Science.gov (United States)

Prangnell, Amy; Shannon, Kate; Nosova, Ekaterina; DeBeck, Kora; Milloy, M-J; Kerr, Thomas; Hayashi, Kanna

2018-02-01

Workplace violence, by clients or predators, poses serious negative health consequences for sex workers. In 2013, the Vancouver (British Columbia), Canada Police Department changed their guidelines with the goal of increasing safety for sex workers by focusing law enforcement on clients and third parties, but not sex workers. We sought to examine the trends and correlates of workplace violence among female sex workers (FSW) before and after the guideline change, using data collected from prospective cohorts of persons who use illicit drugs in Vancouver, Canada. Among 259 FSW, 21.0% reported workplace violence at least once during the study period between 2008 and 2014. There was no statistically significant change in rates of workplace violence after the guideline change. In our multivariable analysis, daily heroin use was independently associated with workplace violence. The 2013 policing guideline change did not appear to have resulted in decreased reports of workplace violence. Increased access to opioid agonist therapies may reduce workplace violence among drug-using FSW.

Mounting for ceramic scroll

Science.gov (United States)

Petty, Jack D.

1993-01-01

A mounting for a ceramic scroll on a metal engine block of a gas turbine engine includes a first ceramic ring and a pair of cross key connections between the first ceramic ring, the ceramic scroll, and the engine block. The cross key connections support the scroll on the engine block independent of relative radial thermal growth and for bodily movement toward an annular mounting shoulder on the engine. The scroll has an uninterrupted annular shoulder facing the mounting shoulder on the engine block. A second ceramic ring is captured between mounting shoulder and the uninterrupted shoulder on the scroll when the latter is bodily shifted toward the mouting shoulder to define a gas seal between the scroll and the engine block.

Solar panel truss mounting systems and methods

Energy Technology Data Exchange (ETDEWEB)

Al-Haddad, Tristan Farris; Cavieres, Andres; Gentry, Russell; Goodman, Joseph; Nolan, Wade; Pitelka, Taylor; Rahimzadeh, Keyan; Brooks, Bradley; Lohr, Joshua; Crooks, Ryan; Porges, Jamie; Rubin, Daniel

2016-06-28

An exemplary embodiment of the present invention provides a solar panel truss mounting system comprising a base and a truss assembly coupled to the base. The truss assembly comprises a first panel rail mount, second panel rail mount parallel to the first panel rail mount, base rail mount parallel to the first and second panel rail mounts, and a plurality of support members. A first portion of the plurality of support members extends between the first and second panel rail mounts. A second portion of the plurality of support members extends between the first panel rail mount and the base rail mount. A third portion of the plurality of support members extends between the second panel rail mount and the base rail mount. The system can further comprise a plurality of connectors for coupling a plurality of photovoltaic solar panels to the truss assembly.

Solar panel truss mounting systems and methods

Energy Technology Data Exchange (ETDEWEB)

Al-Haddad, Tristan Farris; Cavieres, Andres; Gentry, Russell; Goodman, Joseph; Nolan, Wade; Pitelka, Taylor; Rahimzadeh, Keyan; Brooks, Bradley; Lohr, Joshua; Crooks, Ryan; Porges, Jamie; Rubin, Daniel

2018-01-30

An exemplary embodiment of the present invention provides a solar panel truss mounting system comprising a base and a truss assembly coupled to the base. The truss assembly comprises a first panel rail mount, second panel rail mount parallel to the first panel rail mount, base rail mount parallel to the first and second panel rail mounts, and a plurality of support members. A first portion of the plurality of support members extends between the first and second panel rail mounts. A second portion of the plurality of support members extends between the first panel rail mount and the base rail mount. A third portion of the plurality of support members extends between the second panel rail mount and the base rail mount. The system can further comprise a plurality of connectors for coupling a plurality of photovoltaic solar panels to the truss assembly.

Solar panel truss mounting systems and methods

Science.gov (United States)

Al-Haddad, Tristan Farris; Cavieres, Andres; Gentry, Russell; Goodman, Joseph; Nolan, Wade; Pitelka, Taylor; Rahimzadeh, Keyan; Brooks, Bradley; Lohr, Joshua; Crooks, Ryan; Porges, Jamie; Rubin, Daniel

2015-10-20

An exemplary embodiment of the present invention provides a solar panel truss mounting system comprising a base and a truss assembly coupled to the base. The truss assembly comprises a first panel rail mount, second panel rail mount parallel to the first panel rail mount, base rail mount parallel to the first and second panel rail mounts, and a plurality of support members. A first portion of the plurality of support members extends between the first and second panel rail mounts. A second portion of the plurality of support members extends between the first panel rail mount and the base rail mount. A third portion of the plurality of support members extends between the second panel rail mount and the base rail mount. The system can further comprise a plurality of connectors for coupling a plurality of photovoltaic solar panels to the truss assembly.

The Learning Exchange: A Shared Space for the University of British Columbia and Vancouver's Downtown Eastside Communities

Science.gov (United States)

Towle, Angela; Leahy, Kathleen

2016-01-01

The Learning Exchange was established by the University of British Columbia (UBC) in 1999 in Vancouver's Downtown Eastside (DTES). The challenge has been to create a shared space for learning exchanges between two very different communities: a research-intensive university and an inner city area most commonly depicted as a place of hopelessness.…

The head-mounted microscope.

Science.gov (United States)

Chen, Ting; Dailey, Seth H; Naze, Sawyer A; Jiang, Jack J

2012-04-01

Microsurgical equipment has greatly advanced since the inception of the microscope into the operating room. These advancements have allowed for superior surgical precision and better post-operative results. This study focuses on the use of the Leica HM500 head-mounted microscope for the operating phonosurgeon. The head-mounted microscope has an optical zoom from 2× to 9× and provides a working distance from 300 mm to 700 mm. The headpiece, with its articulated eyepieces, adjusts easily to head shape and circumference, and offers a focus function, which is either automatic or manually controlled. We performed five microlaryngoscopic operations utilizing the head-mounted microscope with successful results. By creating a more ergonomically favorable operating posture, a surgeon may be able to obtain greater precision and success in phonomicrosurgery. Phonomicrosurgery requires the precise manipulation of long-handled cantilevered instruments through the narrow bore of a laryngoscope. The head-mounted microscope shortens the working distance compared with a stand microscope, thereby increasing arm stability, which may improve surgical precision. Also, the head-mounted design permits flexibility in head position, enabling operator comfort, and delaying musculoskeletal fatigue. A head-mounted microscope decreases the working distance and provides better ergonomics in laryngoscopic microsurgery. These advances provide the potential to promote precision in phonomicrosurgery. Copyright © 2011 The American Laryngological, Rhinological, and Otological Society, Inc.

Full waveform ambient noise tomography of Mount Rainer

Science.gov (United States)

Flinders, A. F.; Shen, Y.

2014-12-01

Mount Rainier towers over the landscape of western Washington, ranking with Fuji-yama in Japan, Mt. Pinatubo in the Philippines, and Mt. Vesuvius in Italy, as one of the great stratovolcanoes of the world. Notwithstanding it's picturesque stature, Mt. Rainier is potentially the most devastating stratovolcano in North America, with more than 3.5 million people living beneath its shadow in the Seattle-Tacoma area. The primary hazard posed by the volcano is in the form of highly destructive volcanic debris flows (lahars). These lahars form when water and/or melted ice erode away and entrain preexisting volcanic sediment. At Mt. Rainier these flows are often initiated by sector collapse of the volcano's hydrothermally rotten flanks and compounded from Mt. Rainier's extensive snow and glacial ice coverage. It is therefore imperative to ascertain the extent of summit hydrothermal alteration within the volcano, and determine areas prone to collapse. Despite being one of the sixteen volcanoes globally designated by the International Association of Volcanology and Chemistry of the Earth's Interior as warranting detailed and focused study, Mt. Rainier remains enigmatic both in terms of shallow internal structure and the degree of summit hydrothermal alteration. We image this shallow internal structure and areas of possible summit alteration using ambient noise tomography. Our full waveform forward modeling includes high-resolution topography, allowing us to accurately account for the effects of topography on the propagation of short-period Rayleigh waves. Empirical Green's functions were extracted from 80 stations within 200 km of Mount Rainier and compared with synthetic greens functions over multiple frequency bands from 2-28 seconds. The preliminary model shows a broad (60 km wide) low shear-wave velocity anomaly in the mid-crust beneath the volcano. The mid-crust low-velocity body extends to the surface beneath the volcano summit in a narrow near-vertical conduit, the

Channel uranium-graphite reactor mounting

International Nuclear Information System (INIS)

Polushkin, K.K.; Kuznetsov, A.G.; Zheleznyakov, B.N.

1981-01-01

According to theoretical principles of general engineering technology the engineering experience of construction-mounting works at the NPP with channel uranium-graphite reactors is systematized. Main parameters and structural features of the 1000 MW channel uranium-graphite reactors are considered. The succession of mounting operations, premounting equipment and pipelines preparation and mounting works technique are described. The most efficient methods of fitting, welding and machining of reactor elements are recommended. Main problems of technical control service are discussed. A typical netted diagram of main equipment of channel uranium-graphite reactors mounting is given

Preparing for Further Introduction of Computing Technology in Vancouver Community College Instruction. Report of the Instructional Computing Committee.

Science.gov (United States)

Vancouver Community Coll., British Columbia.

After examining the impact of changing technology on postsecondary instruction and on the tools needed for instruction, this report analyzes the status and offers recommendations concerning the future of instructional computing at Vancouver Community College (VCC) in British Columbia. Section I focuses on the use of computers in community college…

Colonization and community: the Vancouver Island coalfield and the making of the British Columbian working class

Energy Technology Data Exchange (ETDEWEB)

Belshaw, J.D. [University College of the Cariboo, Kamloops, BC (Canada). Department of Philosophy, History, and Politics

2002-07-01

During the nineteenth century, coal miners from Europe, Asia, and eastern North America settled on Vancouver Island, British Columbia to mine coal deposits at Nanaimo, Wellington, and Cumberland. The factors that attracted British miners and their families, their expectations and ambitions, and their integration into mining communities are discussed. Working conditions, household wages, racism, industrial organization, gender, schooling, leisure, and community building and identity are considered.

Social capital generators? A case study of industry associations within the Vancouver new media cluster

OpenAIRE

Petrusevich, Michelle Regina

2005-01-01

This thesis uses a case study approach to explore the question: "How do civic associations affect social capital formation in an industrial cluster?" The Vancouver new meda industry is the site of thls research, which is based on over seventy interviews, statistical information from published sources, qualitative and quantitative surveys, and participant observation. The study concludes that civic associations play a crucial role in influencing the production, quality, and amount of social ca...

Detector Mount Design for IGRINS

Directory of Open Access Journals (Sweden)

Jae Sok Oh

2014-06-01

Full Text Available The Immersion Grating Infrared Spectrometer (IGRINS is a near-infrared wide-band high-resolution spectrograph jointly developed by the Korea Astronomy and Space Science Institute and the University of Texas at Austin. IGRINS employs three HAWAII-2RG Focal Plane Array (H2RG FPA detectors. We present the design and fabrication of the detector mount for the H2RG detector. The detector mount consists of a detector housing, an ASIC housing, a Field Flattener Lens (FFL mount, and a support base frame. The detector and the ASIC housing should be kept at 65 K and the support base frame at 130 K. Therefore they are thermally isolated by the support made of GFRP material. The detector mount is designed so that it has features of fine adjusting the position of the detector surface in the optical axis and of fine adjusting yaw and pitch angles in order to utilize as an optical system alignment compensator. We optimized the structural stability and thermal characteristics of the mount design using computer-aided 3D modeling and finite element analysis. Based on the structural and thermal analysis, the designed detector mount meets an optical stability tolerance and system thermal requirements. Actual detector mount fabricated based on the design has been installed into the IGRINS cryostat and successfully passed a vacuum test and a cold test.

Mount Athos: Between autonomy and statehood

Directory of Open Access Journals (Sweden)

Avramović Dragutin

2013-01-01

Full Text Available Legal status of the Mount Athos is characterized by many special features that make it internationally unique legal regime. The author analyzes peculiarities of Mount Athos territorial status, legal position of residents and visitors, as well as organization of Mount Athos authorities. The author concludes that the Mount Athos is characterized by a kind of para-sovereignty. Its autonomy involves not only the internal organization, autonomous governance and religious autonomy, but it also includes many elements of secular life of their visitors. Mount Athos has its own, separate legislative, administrative and judicial powers, while the Statute of the Mount Athos has greater legal force than all the other laws of the Greek state, because the state can not unilaterally change its provisions. Having in mind that the wide self-government is vested in church authorities and that the monks have very specific way of living, the author takes a position that the Mount Athos represent 'monastic state', but without statehood. The author also states that the Mount Athos will be faced with many challenges in the context of spreading of an assimilating, universal conception of human rights.

High-resolution digital elevation model of lower Cowlitz and Toutle Rivers, adjacent to Mount St. Helens, Washington, based on an airborne lidar survey of October 2007

Science.gov (United States)

Mosbrucker, Adam

2015-01-01

The lateral blast, debris avalanche, and lahars of the May 18th, 1980, eruption of Mount St. Helens, Washington, dramatically altered the surrounding landscape. Lava domes were extruded during the subsequent eruptive periods of 1980–1986 and 2004–2008. More than three decades after the emplacement of the 1980 debris avalanche, high sediment production persists in the Toutle River basin, which drains the northern and western flanks of the volcano. Because this sediment increases the risk of flooding to downstream communities on the Toutle and lower Cowlitz Rivers, the U.S. Army Corps of Engineers (USACE), under the direction of Congress to maintain an authorized level of flood protection, continues to monitor and mitigate excess sediment in North and South Fork Toutle River basins to help reduce this risk and to prevent sediment from clogging the shipping channel of the Columbia River. From October 22–27, 2007, Watershed Sciences, Inc., under contract to USACE, collected high-precision airborne lidar (light detection and ranging) data that cover 273 square kilometers (105 square miles) of lower Cowlitz and Toutle River tributaries from the Columbia River at Kelso, Washington, to upper North Fork Toutle River (below the volcano's edifice), including lower South Fork Toutle River. These data provide a digital dataset of the ground surface, including beneath forest cover. Such remotely sensed data can be used to develop sediment budgets and models of sediment erosion, transport, and deposition. The U.S. Geological Survey (USGS) used these lidar data to develop digital elevation models (DEMs) of the study area. DEMs are fundamental to monitoring natural hazards and studying volcanic landforms, fluvial and glacial geomorphology, and surface geology. Watershed Sciences, Inc., provided files in the LASer (LAS) format containing laser returns that had been filtered, classified, and georeferenced. The USGS produced a hydro-flattened DEM from ground-classified points at

Cretaceous origin of dogwoods: an anatomically preserved Cornus (Cornaceae fruit from the Campanian of Vancouver Island

Directory of Open Access Journals (Sweden)

Brian A. Atkinson

2016-12-01

Full Text Available Background Cornaceae consists of 58 species, all within the genus Cornus. The Cenozoic record of Cornus is extensive and well documented. Molecular divergence-time studies suggest that crown-group Cornus may have originated by the Late Cretaceous. However, there has been no formal report of Cornus from Cretaceous deposits. Here, we characterize a permineralized fossil fruit assignable to Cornus subg. Cornus from the Upper Cretaceous (Campanian Shelter Point locality of Vancouver Island, British Columbia, Canada. Methods Serial sections of the specimen were made using the cellulose acetate peel technique. Peels were mounted onto microscope slides and studied by light microscopy. Results The fossil fruit consists of a tri-locular woody endocarp with dorsal germination valves. The locules are sub-triangular to ellipsoidal in transverse section and are separated by thin septa. Endocarp tissue consists of elongated and isodiametric sclereids and secretory cavities. Internal vascular tissue was not observed, but is interpreted to have been located along the outer periphery of the septa for some length, common in many cornalean taxa. There is one seed in each locule, one of which was found to have endosperm and a dicotyledonous embryo. Discussion Woody endocarps with germination valves, without central vascular bundles, and with one seed per locule are characteristic of several families within the order Cornales. The interpreted vascular pattern and presence of secretory cavities indicates that the fossil fruit is assignable to Cornus subg. Cornus. Comparative analysis suggests that the fossil is most similar to Cornus piggae, a species described from the Paleocene of North Dakota. This fossil is the first evidence of crown-group Cornaceae from the Cretaceous and sheds light on both the plesiomorphic fruit characters and the timing of the initial diversification of the family and basal asterid lineage, Cornales.

Perks of controlled circ: a case study of the distribution practices of Vancouver and Western Living magazines

OpenAIRE

Law, Melanie

2007-01-01

This report examines controlled-circulation magazines using Vancouver and Western Living magazines as successful examples. It provides an analysis of the workings of controlled circulation with reference to advertising, editorial, branding, and operations, and shows how magazines with this distribution method can be successful despite publishing professionals’ common assumption that controlled-circulation magazines are of lesser quality than paid-circulation magazines.

Canwest propane: Canwest Propane's newest terminal delivers the winning conditions for B.C. market expansion

International Nuclear Information System (INIS)

Anon

2004-01-01

Opening of a new propane terminal in Surrey, BC by Canwest Propane Ltd., is reported. The facility is the first rail terminal opened by Canwest, and is intended to serve the greater Vancouver area, Vancouver island and the US Northwest, specifically Washington State. The Surrey location allows the company to service its business by rail, the most efficient method of getting product to the Lower Mainland. The facility sits on 4.5 acres of land; a CN rail track runs alongside the site, where six 30,000 gallon storage tanks are located. About 60 million litres of propane is expected to be distributed from the terminal, with further expansion anticipated both on Vancouver Island and in the US Northwest. photos

12 CFR 4.4 - Washington office.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Washington office. 4.4 Section 4.4 Banks and... EXAMINERS Organization and Functions § 4.4 Washington office. The Washington office of the OCC is the main office and headquarters of the OCC. The Washington office directs OCC policy, oversees OCC operations...

Historical changes to Lake Washington and route of the Lake Washington Ship Canal, King County, Washington

Science.gov (United States)

Chrzastowski, Michael J.

1983-01-01

Lake Washington, in the midst of the greater Seattle metropolitan area of the Puget Sound region (fig. 1), is an exceptional commercial, recreational, and esthetic resource for the region . In the past 130 years, Lake Washington has been changed from a " wild " lake in a wilderness setting to a regulated lake surrounded by a growing metropolis--a transformation that provides an unusual opportunity to study changes to a lake's shoreline and hydrologic characteristics -resulting from urbanization.

Sustainability and public health nutrition at school: assessing the integration of healthy and environmentally sustainable food initiatives in Vancouver schools.

Science.gov (United States)

Black, Jennifer L; Velazquez, Cayley E; Ahmadi, Naseam; Chapman, Gwen E; Carten, Sarah; Edward, Joshua; Shulhan, Stephanie; Stephens, Teya; Rojas, Alejandro

2015-09-01

To describe the development and application of the School Food Environment Assessment Tools and a novel scoring system to assess the integration of healthy and environmentally sustainable food initiatives in elementary and secondary schools. The cross-sectional study included direct observations of physical food environments and interviews with key school personnel regarding food-related programmes and policies. A five-point scoring system was then developed to assess actions across six domains: (i) food gardens; (ii) composting systems; (iii) food preparation activities; (iv) food-related teaching and learning activities; and availability of (v) healthy food; and (vi) environmentally sustainable food. Vancouver, Canada. A purposive sample of public schools (n 33) from all six sectors of the Vancouver Board of Education. Schools scored highest in the areas of food garden and compost system development and use. Regular integration of food-related teaching and learning activities and hands-on food preparation experiences were also commonly reported. Most schools demonstrated rudimentary efforts to make healthy and environmentally sustainable food choices available, but in general scored lowest on these two domains. Moreover, no schools reported widespread initiatives fully supporting availability or integration of healthy or environmentally sustainable foods across campus. More work is needed in all areas to fully integrate programmes and policies that support healthy, environmentally sustainable food systems in Vancouver schools. The assessment tools and proposed indicators offer a practical approach for researchers, policy makers and school stakeholders to assess school food system environments, identify priority areas for intervention and track relevant changes over time.

Academic performance and educational pathways of young allophones: A comparative multivariate analysis of Montreal, Toronto, and Vancouver

Directory of Open Access Journals (Sweden)

Jacques Ledent

2013-05-01

Full Text Available Using several local and provincial data banks enabling one to follow the school progression of the cohort of students who, in Canada’s three main immigration-destination cities, were expected to graduate secondary school in 2004, this article examines the academic performance and educational pathways of those students who at home use a language other the main language of schooling: non-French speakers in Montreal and non-English speakers in Toronto and Vancouver. First, after accounting for differences in characteristics, those students (target group are shown to succeed better than the remaining students (comparison group, especially in Vancouver. However, within the target group, there appear to be substantial differences in performance between linguistic subgroups, which are far from being similar in all three cities. Second, the individual and contextual factors that influence the academic performance of the students in the target group appear to be similar for some and different for others in the three cities, while presenting some more-or-less large discrepancies with the corresponding factors pertaining to the comparison group. The article concludes with a few policy implications.

Flush Mounting Of Thin-Film Sensors

Science.gov (United States)

Moore, Thomas C., Sr.

1992-01-01

Technique developed for mounting thin-film sensors flush with surfaces like aerodynamic surfaces of aircraft, which often have compound curvatures. Sensor mounted in recess by use of vacuum pad and materials selected for specific application. Technique involves use of materials tailored to thermal properties of substrate in which sensor mounted. Together with customized materials, enables flush mounting of thin-film sensors in most situations in which recesses for sensors provided. Useful in both aircraft and automotive industries.

“Columns of the House” and Proud Workers: Greek Immigrant Women in Vancouver, 1954-1975

OpenAIRE

Kalogeropoulou, Maria

2015-01-01

In this thesis, I study the experiences of eight first-generation Greek immigrant women who moved to Vancouver between 1954 and 1975 by listening to and contextualizing their oral life histories. Looking at their lives before they immigrated, I explore how these women’s gender experiences were very much shaped by religion, class, and rural vis-à-vis urban locations in Greece. I also demonstrate that many exercised agency in this patriarchal culture, and that they were part of the decision-mak...

Characterization of Engine Mount Elastomers

National Research Council Canada - National Science Library

Szabo, Jeffrey P

2005-01-01

As part of a project to develop methods for modelling the performance of engine mounts, several oil resistant alternative materials were prepared, and compared to conventional materials from mounts...

Better Jobs, Brighter Futures, a Stronger Washington. Washington's Community and Technical Colleges

Science.gov (United States)

Washington State Board for Community and Technical Colleges, 2015

2015-01-01

The world is changing rapidly. With changes in technology, demographics, and workforce trends, Washington needs colleges to not only keep pace, but lead the way. Washington's 34 community and technical colleges answer that call. The community and technical colleges have proven uniquely positioned to adapt to, embrace, and ignite change. Community…

Oil spill response issues in Washington State

International Nuclear Information System (INIS)

Lempriere, P.R.

1997-01-01

Washington State statutes and regulations applicable to oil transport and oil spills were described. Specific provisions of the statutes and regulations and other relevant matters were also discussed. Among these were: (1) Washington State oil spill prevention plans, (2) Washington State oil spill contingency plans, (3) best achievable protection, (4) Intertanko's lawsuit against Washington State, (5) oil spill removal organizations, (6) certificates of financial responsibility in Washington State, (7) extent of potential liability under Washington Law, (8) disposal of cleanup materials, and (9) definition of 'qualified individuals' on marine vessels having the authority to implement removal actions

Solar panel parallel mounting configuration

Science.gov (United States)

Mutschler, Jr., Edward Charles (Inventor)

1998-01-01

A spacecraft includes a plurality of solar panels interconnected with a power coupler and an electrically operated device to provide power to the device when the solar cells are insolated. The solar panels are subject to bending distortion when entering or leaving eclipse. Spacecraft attitude disturbances are reduced by mounting each of the solar panels to an elongated boom made from a material with a low coefficient of thermal expansion, so that the bending of one panel is not communicated to the next. The boom may be insulated to reduce its bending during changes in insolation. A particularly advantageous embodiment mounts each panel to the boom with a single mounting, which may be a hinge. The single mounting prevents transfer of bending moments from the panel to the boom.

A multi-scale approach to monitor urban carbon-dioxide emissions in the atmosphere over Vancouver, Canada

Science.gov (United States)

Christen, A.; Crawford, B.; Ketler, R.; Lee, J. K.; McKendry, I. G.; Nesic, Z.; Caitlin, S.

2015-12-01

Measurements of long-lived greenhouse gases in the urban atmosphere are potentially useful to constrain and validate urban emission inventories, or space-borne remote-sensing products. We summarize and compare three different approaches, operating at different scales, that directly or indirectly identify, attribute and quantify emissions (and uptake) of carbon dioxide (CO2) in urban environments. All three approaches are illustrated using in-situ measurements in the atmosphere in and over Vancouver, Canada. Mobile sensing may be a promising way to quantify and map CO2 mixing ratios at fine scales across heterogenous and complex urban environments. We developed a system for monitoring CO2 mixing ratios at street level using a network of mobile CO2 sensors deployable on vehicles and bikes. A total of 5 prototype sensors were built and simultaneously used in a measurement campaign across a range of urban land use types and densities within a short time frame (3 hours). The dataset is used to aid in fine scale emission mapping in combination with simultaneous tower-based flux measurements. Overall, calculated CO2 emissions are realistic when compared against a spatially disaggregated scale emission inventory. The second approach is based on mass flux measurements of CO2 using a tower-based eddy covariance (EC) system. We present a continuous 7-year long dataset of CO2 fluxes measured by EC at the 28m tall flux tower 'Vancouver-Sunset'. We show how this dataset can be combined with turbulent source area models to quantify and partition different emission processes at the neighborhood-scale. The long-term EC measurements are within 10% of a spatially disaggregated scale emission inventory. Thirdly, at the urban scale, we present a dataset of CO2 mixing ratios measured using a tethered balloon system in the urban boundary layer above Vancouver. Using a simple box model, net city-scale CO2 emissions can be determined using measured rate of change of CO2 mixing ratios

High-resolution digital elevation model of Mount St. Helens crater and upper North Fork Toutle River basin, Washington, based on an airborne lidar survey of September 2009

Science.gov (United States)

Mosbrucker, Adam

2014-01-01

The lateral blast, debris avalanche, and lahars of the May 18th, 1980, eruption of Mount St. Helens, Washington, dramatically altered the surrounding landscape. Lava domes were extruded during the subsequent eruptive periods of 1980–1986 and 2004–2008. More than three decades after the emplacement of the 1980 debris avalanche, high sediment production persists in the North Fork Toutle River basin, which drains the northern flank of the volcano. Because this sediment increases the risk of flooding to downstream communities on the Toutle and Cowlitz Rivers, the U.S. Army Corps of Engineers (USACE), under the direction of Congress to maintain an authorized level of flood protection, built a sediment retention structure on the North Fork Toutle River in 1989 to help reduce this risk and to prevent sediment from clogging the shipping channel of the Columbia River. From September 16–20, 2009, Watershed Sciences, Inc., under contract to USACE, collected high-precision airborne lidar (light detection and ranging) data that cover 214 square kilometers (83 square miles) of Mount St. Helens and the upper North Fork Toutle River basin from the sediment retention structure to the volcano's crater. These data provide a digital dataset of the ground surface, including beneath forest cover. Such remotely sensed data can be used to develop sediment budgets and models of sediment erosion, transport, and deposition. The U.S. Geological Survey (USGS) used these lidar data to develop digital elevation models (DEMs) of the study area. DEMs are fundamental to monitoring natural hazards and studying volcanic landforms, fluvial and glacial geomorphology, and surface geology. Watershed Sciences, Inc., provided files in the LASer (LAS) format containing laser returns that had been filtered, classified, and georeferenced. The USGS produced a hydro-flattened DEM from ground-classified points at Castle, Coldwater, and Spirit Lakes. Final results averaged about five laser last

Mounting Thin Samples For Electrical Measurements

Science.gov (United States)

Matus, L. G.; Summers, R. L.

1988-01-01

New method for mounting thin sample for electrical measurements involves use of vacuum chuck to hold a ceramic mounting plate, which holds sample. Contacts on mounting plate establish electrical connection to sample. Used to make electrical measurements over temperature range from 77 to 1,000 K and does not introduce distortions into magnetic field during Hall measurements.

Realizing User-Relevant Conceptual Model for the Ski Jump Venue of the Vancouver 2010 Winter Olympics

Science.gov (United States)

Teakles, Andrew; Mo, Ruping; Dierking, Carl F.; Emond, Chris; Smith, Trevor; McLennan, Neil; Joe, Paul I.

2014-01-01

As was the case for most other Olympic competitions, providing weather guidance for the ski jump and Nordic combined events involved its own set of unique challenges. The extent of these challenges was brought to light before the Vancouver 2010 Winter Olympics during a series of outflow wind events in the 2008/2009 winter season. The interactions with the race officials during the difficult race conditions brought on by the outflows provided a new perspective on the service delivery requirements for the upcoming Olympic Games. In particular, the turbulent nature of the winds and its impact on the ski jump practice events that season highlighted the need of race officials for nowcasting advice at very short time scales (from 2 min to 1 h) and forecast products tailored to their decision-making process. These realizations resulted in last minute modifications to the monitoring strategy leading up to the Olympic Games and required forecasters' conceptual models for flow within the Callaghan Valley to be downscaled further to reflect the evolution of turbulence at the ski jump site. The SNOW-V10 (Science of Nowcasting Olympic Weather for Vancouver 2010) team provided support for these efforts by supplying diagnostic case analyses of important events using numerical weather data and by enhancing the real-time monitoring capabilities at the ski jump venue.

Resilient mounting systems in buildings

NARCIS (Netherlands)

Breeuwer, R.; Tukker, J.C.

1976-01-01

The basic elements of resilient mounting systems are described and various measures for quantifying the effect of such systems defined. Using electrical analogue circuits, the calculation of these measures is illustrated. With special reference to resilient mounting systems in buildings, under

Assessment of increased thermal activity at Mount Baker, Washington, March 1975-March 1976

Science.gov (United States)

Frank, David; Meier, Mark Frederick; Swanson, Donald A.; with contributions by Babcock, James W.; Fretwell, Marvin O.; Malone, Stephen D.; Rosenfeld, Charles L.; Shreve, Ronald L.; Wilcox, Ray E.

1977-01-01

In March 1975 Mount Baker showed a large increase in thermal emission, which has persisted for more than 1 year. Fumarole ejecta accompanied the thermal activity from March to September, but the ejecta had no constituents that suggest a magmatic source. Estimates of that part of the total heat flux that would account for the observed snow and ice loss show that the heat-flow increase was roughly one order of magnitude, from about 2 megawatts at 10 watts per square meter, averaged over Sherman Crater before 1975, to about 30 megawatts at 180 watts per square meter, during 1975. Almost half of the glacier that occupied the basin of Sherman Crater was melted in 1975. The new activity generated great concern among the public and the government agencies responsible for geological evaluation of potential hazards and for protection of life and property. The past geologic history, current topography, rock alteration, and location of major fumarolic activity indicate that large rock avalanches and mudflows on the east slope in Boulder Creek valley are the potential hazards of most significance related to present conditions. The most probable types of large mass movements would be mudflows, having speeds of as much as 50 kilometers per hour, that would originate from mixtures of snow, ice, and melt water and avalanches of structurally weak clay-rich rocks that make up the rim of Sherman Crater. Similar mudflows from the volcano have traveled at least 12 kilometers 8 times during the past 10,000 years. A possible worst case event, however, might be a larger, air-cushioned avalanche of as much as 20 to 30 million cubic meters that could hit Baker Lake at speeds of more than 300 kilometers per hour and generate a wave of water large enough to overtop Upper Baker Dam. At least 30 million cubic meters of potentially unstable material occurs as hydrothermally altered remnants of the rim of Sherman Crater and could provide the required volume for the estimated worst case event or

Low-Thermal-Resistance Baseplate Mounting

Science.gov (United States)

Perreault, W. T.

1984-01-01

Low-thermal-resistance mounting achieved by preloading baseplate to slight convexity with screws threaded through beam. As mounting bolts around edge of base-place tightened, baseplate and cold plate contact first in center, with region of intimate contact spreading outward as bolts tightened.

An improved loopless mounting method for cryocrystallography

International Nuclear Information System (INIS)

Jian-Xun, Qi; Fan, Jiang

2010-01-01

Based on a recent loopless mounting method, a simplified loopless and bufferless crystal mounting method is developed for macromolecular crystallography. This simplified crystal mounting system is composed of the following components: a home-made glass capillary, a brass seat for holding the glass capillary, a flow regulator, and a vacuum pump for evacuation. Compared with the currently prevalent loop mounting method, this simplified method has almost the same mounting procedure and thus is compatible with the current automated crystal mounting system. The advantages of this method include higher signal-to-noise ratio, more accurate measurement, more rapid flash cooling, less x-ray absorption and thus less radiation damage to the crystal. This method can be extended to the flash-freeing of a crystal without or with soaking it in a lower concentration of cryoprotectant, thus it may be the best option for data collection in the absence of suitable cryoprotectant. Therefore, it is suggested that this mounting method should be further improved and extensively applied to cryocrystallographic experiments. (general)

An improved loopless mounting method for cryocrystallography

Science.gov (United States)

Qi, Jian-Xun; Jiang, Fan

2010-01-01

Based on a recent loopless mounting method, a simplified loopless and bufferless crystal mounting method is developed for macromolecular crystallography. This simplified crystal mounting system is composed of the following components: a home-made glass capillary, a brass seat for holding the glass capillary, a flow regulator, and a vacuum pump for evacuation. Compared with the currently prevalent loop mounting method, this simplified method has almost the same mounting procedure and thus is compatible with the current automated crystal mounting system. The advantages of this method include higher signal-to-noise ratio, more accurate measurement, more rapid flash cooling, less x-ray absorption and thus less radiation damage to the crystal. This method can be extended to the flash-freeing of a crystal without or with soaking it in a lower concentration of cryoprotectant, thus it may be the best option for data collection in the absence of suitable cryoprotectant. Therefore, it is suggested that this mounting method should be further improved and extensively applied to cryocrystallographic experiments.

AVTA Federal Fleet PEV Readiness Data Logging and Characterization Study for the National Park Service: Fort Vancouver National Historic Site

Energy Technology Data Exchange (ETDEWEB)

Stephen Schey; Jim Francfort

2014-03-01

significant reductions in emission of greenhouse gases and petroleum use, while also reducing fuel costs. The Vancouver, Washington area and neighboring Portland, Oregon are leaders in adoption of PEVs in the United States1. PEV charging stations, or more appropriately identified as electric vehicle supply equipment, located on the FVNHS facility would be a benefit for both FVNHS fleets and general public use. Fleet drivers and park visitors operating privately owned plug-in electric vehicles benefit by using the charging infrastructure. ITSNA recommends location analysis of the FVNHS site to identify the optimal station placement for electric vehicle supply equipment. ITSNA recognizes the support of Idaho National Laboratory and ICF International for their efforts to initiate communication with the National Parks Service and FVNHS for participation in this study. ITSNA is pleased to provide this report and is encouraged by the high interest and support from the National Park Service and FVNHS personnel

Food and beverage promotions in Vancouver schools: A study of the prevalence and characteristics of in-school advertising, messaging, and signage.

Science.gov (United States)

Velazquez, Cayley E; Black, Jennifer L; Ahmadi, Naseam

2015-01-01

The purpose of this study was to provide a descriptive profile of food-related advertising, messaging, and signage in Vancouver schools and to examine differences in the prevalence and characteristics of promotions between elementary and secondary schools. All food-related promotions were photographed in 23 diverse Vancouver public schools between November 2012 and April 2013. Key attributes, including the location, size, and main purpose of each promotion, as well as the type of food and/or beverage advertised and compliance with provincial school nutrition guidelines, were coded. Descriptive statistics assessed the prevalence and characteristics of promotions. Cross-tabulations examined whether the promotional landscape differed between elementary and secondary schools. All secondary and 80% of elementary schools contained food or beverage promotions (median = 17, range = 0-57 promotions per school). Of the 493 promotions documented, approximately 25% depicted "choose least" or "not recommended" items, prohibited for sale by provincial school nutrition guidelines. Nearly 1/3 of promotions advertised commercial items (e.g., brand name beverages such as Pepsi), in violation of the Board of Education's advertising policies and only 13% conveyed nutrition education messages. Close to half of all promotions were created by students for class projects, many of which marketed minimally nutritious items. In Vancouver schools, food-related promotions are common and are more prevalent in secondary than elementary schools. Students are regularly exposed to messaging for nutritionally poor items that are not in compliance with provincial school nutrition guidelines and which violate school board advertising policies. Stronger oversight of food-related promotional materials is needed to ensure that schools provide health promoting food environments.

Collaborative Citation Analysis and Accuracy Degree of Vancouver Style Application in References Of The Scientific Journal of Birjand University Of Medical Sciences: Short Communication

Directory of Open Access Journals (Sweden)

halimeh sadeghi

2015-04-01

Conclusion: It was found that in the bibliography Of the cited English articles, Vancouver style had not been applied completely, which should be paid attention to by scholars in their initial surveying of the articles.

Multi-Mounted X-Ray Computed Tomography.

Science.gov (United States)

Fu, Jian; Liu, Zhenzhong; Wang, Jingzheng

2016-01-01

Most existing X-ray computed tomography (CT) techniques work in single-mounted mode and need to scan the inspected objects one by one. It is time-consuming and not acceptable for the inspection in a large scale. In this paper, we report a multi-mounted CT method and its first engineering implementation. It consists of a multi-mounted scanning geometry and the corresponding algebraic iterative reconstruction algorithm. This approach permits the CT rotation scanning of multiple objects simultaneously without the increase of penetration thickness and the signal crosstalk. Compared with the conventional single-mounted methods, it has the potential to improve the imaging efficiency and suppress the artifacts from the beam hardening and the scatter. This work comprises a numerical study of the method and its experimental verification using a dataset measured with a developed multi-mounted X-ray CT prototype system. We believe that this technique is of particular interest for pushing the engineering applications of X-ray CT.

The 2004–2008 dome-building eruption at Mount St. Helens, Washington: Epilogue

Science.gov (United States)

Dzurisin, Daniel; Moran, Seth C.; Lisowski, Michael; Schilling, Steve P.; Anderson, Kyle R.; Werner, Cynthia A.

2015-01-01

The 2004–2008 dome-building eruption at Mount St. Helens ended during winter 2007–2008 at a time when field observations were hampered by persistent bad weather. As a result, recognizing the end of the eruption was challenging—but important for scientists trying to understand how and why long-lived eruptions end and for public officials and land managers responsible for hazards mitigation and access restrictions. In hindsight, the end of the eruption was presaged by a slight increase in seismicity in December 2007 that culminated on January 12–13, 2008, with a burst of more than 500 events, most of which occurred in association with several tremor-like signals and a spasmodic burst of long-period earthquakes. At about the same time, a series of regular, localized, small-amplitude tilt events—thousands of which had been recorded during earlier phases of the eruption—came to an end. Thereafter, seismicity declined to 10–20 events per day until January 27–28, when a spasmodic burst of about 50 volcano-tectonic earthquakes occurred over a span of 3 h. This was followed by a brief return of repetitive “drumbeat” earthquakes that characterized much of the eruption. By January 31, however, seismicity had declined to 1–2 earthquakes per day, a rate similar to pre-eruption levels. We attribute the tilt and seismic observations to convulsive stagnation of a semisolid magma plug in the upper part of the conduit. The upward movement of the plug ceased when the excess driving pressure, which had gradually decreased throughout the eruption as a result of reservoir deflation and increasing overburden from the growing dome, was overcome by increasing friction as a result of cooling and crystallization of the plug.

Housing And Mounting Structure

Science.gov (United States)

Anderson, Gene R.; Armendariz, Marcelino G.; Baca, Johnny R.F.; Bryan, Robert P.; Carson, Richard F.; Duckett, III, Edwin B.; McCormick, Frederick B.; Miller, Gregory V.; Peterson, David W.; Smith, Terrance T.

2005-03-08

This invention relates to an optical transmitter, receiver or transceiver module, and more particularly, to an apparatus for connecting a first optical connector to a second optical connector. The apparatus comprises: (1) a housing having at least a first end and at least a second end, the first end of the housing capable of receiving the first optical connector, and the second end of the housing capable of receiving the second optical connector; (2) a longitudinal cavity extending from the first end of the housing to the second end of the housing; and (3) an electromagnetic shield comprising at least a portion of the housing. This invention also relates to an apparatus for housing a flexible printed circuit board, and this apparatus comprises: (1) a mounting structure having at least a first surface and a second surface; (2) alignment ridges along the first and second surfaces of the mounting structure, the alignment ridges functioning to align and secure a flexible printed circuit board that is wrapped around and attached to the first and second surfaces of the mounting structure; and (3) a series of heat sink ridges adapted to the mounting structure, the heat sink ridges functioning to dissipate heat that is generated from the flexible printed circuit board.

The 1980-1982 Geothermal Resource Assessment Program in Washington

Energy Technology Data Exchange (ETDEWEB)

Korosec, Michael A.; Phillips, William M.; Schuster, J.Eric

1983-08-01

Since 1978, the Division of Geology and Earth Resources of the Washington Department of Natural Resources has participated in the U.S. Department of Energy's (USDOE) State-Coupled Geothermal Resource Program. Federal and state funds have been used to investigate and evaluate the potential for geothermal resources, on both a reconnaissance and area-specific level. Preliminary results and progress reports for the period up through mid-1980 have already been released as a Division Open File Report (Korosec, Schuster, and others, 1981). Preliminary results and progress summaries of work carried out from mid-1980 through the end of 1982 are presented in this report. Only one other summary report dealing with geothermal resource investigations in the state has been published. An Information Circular released by the Division (Schuster and others, 1978) compiled the geology, geochemistry, and heat flow drilling results from a project in the Indian Heaven area in the south Cascades. The previous progress report for the geothermal program (Korosec, Schuster, and others, 1981) included information on temperature gradients measured throughout the state, heat flow drilling in the southern Cascades, gravity surveys for the southern Cascades, thermal and mineral spring investigations, geologic mapping for the White Pass-Tumac Mountain area, and area specific studies for the Camas area of Clark County and Mount St. Helens. This work, along with some additional studies, led to the compilation of the Geothermal Resources of Washington map (Korosec, Kaler, and others, 1981). The map is principally a nontechnical presentation based on all available geothermal information, presented as data points, tables, and text on a map with a scale of 1:500,000.

PECULIARITIES OF ASSIGNMENT OF ROLLING BEARING MOUNTING AND PARAMETERS OF GEOMETRIC ACCURACY OF MOUNTING SURFACES OF SHAFTS AND FRAMES

Directory of Open Access Journals (Sweden)

Adamenko Yu. І.

2017-04-01

Full Text Available The standards and methods concerning assignment of rolling bearing fit with shafts and frames via example of bearing 6-208 are analyzed. We set certain differences of recommendations according to GOST 3325-85, "Rolling bearings. Tolerance zones and technical requirements to mounting surfaces of shafts and frames. Attachment" and by reference of rolling bearing manufacturers. The following factors should be taken into consideration when assigning the mounting with the tension the internal ring of the bearing with shaft and mounting with a gap in the outer ring with a housing bore. The methods of achieving accuracy of mounting surfaces of shafts and frames via form tolerance assignment: roundness tolerance, profile of longitudinal cut, cross section, cylindricity and others. It is possible to limit the bearing rings in different ways, for example appointing the cylindrical mounting surfaces and bead end surfaces the appropriate tolerances, namely: coaxiality tolerance or full radial beat of mounting surfaces, and also perpendicularity tolerance, butt beats and full butt beats of mounting end surfaces. We suggest to expand methods of achieving the accuracy of shafts and frames depending on seriation of production and production operations metrology support.

Social influences upon injection initiation among street-involved youth in Vancouver, Canada: a qualitative study

Directory of Open Access Journals (Sweden)

Wood Evan

2009-04-01

Full Text Available Abstract Background Street-involved youth are a population at risk of adopting injection as a route of administration, and preventing the transition to injection drug use among street youth represents a public health priority. In order to inform epidemiological research and prevention efforts, we conducted a qualitative study to investigate the initiation of injection drug use among street-involved youth in Vancouver, Canada. Methods Qualitative interviews with street youth who inject drugs elicited descriptions of the adoption of injection as a route of administration. Interviewees were recruited from the At-Risk Youth Study (ARYS, a cohort of street-involved youth who use illicit drugs in Vancouver, Canada. Audio recorded interviews were transcribed verbatim and a thematic analysis was conducted. Results 26 youth aged 16 to 26 participated in this study, including 12 females. Among study participants the first injection episode frequently featured another drug user who facilitated the initiation of injecting. Youth narratives indicate that the transition into injecting is influenced by social interactions with drug using peers and evolving perceptions of injecting, and rejecting identification as an injector was important among youth who did not continue to inject. It appears that social conventions discouraging initiating young drug users into injection exist among established injectors, although this ethic is often ignored. Conclusion The importance of social relationships with other drug users within the adoption of injection drug use highlights the potential of social interventions to prevent injection initiation. Additionally, developing strategies to engage current injectors who are likely to initiate youth into injection could also benefit prevention efforts.

Mounting support for a photovoltaic module

Science.gov (United States)

Brandt, Gregory Michael; Barsun, Stephan K.; Coleman, Nathaniel T.; Zhou, Yin

2013-03-26

A mounting support for a photovoltaic module is described. The mounting support includes a foundation having an integrated wire-way ledge portion. A photovoltaic module support mechanism is coupled with the foundation.

Socio Economic Status and Traumatic Brain Injury amongst Pediatric Populations: A Spatial Analysis in Greater Vancouver

Directory of Open Access Journals (Sweden)

Ofer Amram

2015-12-01

Full Text Available Introduction: Within Canada, injuries are the leading cause of death amongst children fourteen years of age and younger, and also one of the leading causes of morbidity. Low Socio Economic Status (SES seems to be a strong indicator of a higher prevalence of injuries. This study aims to identify hotspots for pediatric Traumatic Brain Injury (TBI and examines the relationship between SES and pediatric TBI rates in greater Vancouver, British Columbia (BC, Canada. Methods: Pediatric TBI data from the BC Trauma Registry (BCTR was used to identify all pediatric TBI patients admitted to BC hospitals between the years 2000 and 2013. Spatial analysis was used to identify hotspots for pediatric TBI. Multivariate analysis was used to distinguish census variables that were correlated with rates of injury. Results: Six hundred and fifty three severe pediatric TBI injuries occurred within the BC Lower Mainland between 2000 and 2013. High rates of injury were concentrated in the East, while low rate clusters were most common in the West of the region (more affluent neighborhoods. A low level of education was the main predictor of a high rate of injury (OR = 1.13, 95% CI = 1.03–1.23, p-Value 0.009. Conclusion: While there was a clear relationship between different SES indicators and pediatric TBI rates in greater Vancouver, income-based SES indicators did not serve as good predictors within this region.

PBO Borehole Strainmeters: 2017 Episodic Tremor and Slip Event for Southern Vancouver Island, BC, Canada through Olympia, WA, USA

Science.gov (United States)

Van Boskirk, E. J.; Hodgkinson, K. M.; Gottlieb, M. H.; Johnson, W.; Henderson, D. B.; Mencin, D.; Mattioli, G. S.

2017-12-01

The Plate Boundary Observatory's (PBO) borehole strainmeters along the Cascadia Subduction Zone (CSZ) record the development and migration of Episodic Tremor and Slip (ETS). Along the southern Vancouver Island to Olympia, WA portion of the CSZ ETS events seem to repeat every 14 months. ETS events are non-volcanic tremor swarms that occur over periods of weeks, often migrating along segments of the subduction zone and can release the energy equivalent to a M7 or greater earthquake. Each ETS event is different; initial propagation location, ETS movement, duration, and direction all vary. Constraints provided by strainmeter observations of ETS events illuminate strain release patterns along the subducting slab interface and may help resolve questions regarding the location of the locked zone of the slab and what role ETS events play in the CSZ earthquake cycle. The 2017 CSZ ETS began in early February continuing through early April. Beginning in the northern Olympic Peninsula, near Port Angeles, it migrated south towards Olympia over the course of a week. After a two week pause it resumed under the Straits of Juan de Fuca and propagated northwest under Vancouver Island. There are 15 PBO borehole strainmeters along this segment, and ETS strain observations correlate with seismic and GPS measurements. The PBO borehole strainmeters are sensitive even over great distances from the ETS epicenters, and observe compression or extension relative to the ETS migration. Openly available PBO borehole strainmeter data used by the community has made significant contributions to understanding the ETS process, including the determination that ETS slip is tidally modulated. Data are publically available through UNAVCO and IRIS, which provide links to online tutorials and scripts. There are 32 strainmeters covering the CSZ from southern Vancouver Island, Canada to northern California, USA, and data spans back to 2005. Each site has a Gladwin tensor borehole strainmeter, a Malin three

Systems and methods for mirror mounting with minimized distortion

Science.gov (United States)

Antonille, Scott R. (Inventor); Wallace, Thomas E. (Inventor); Content, David A. (Inventor); Wake, Shane W. (Inventor)

2012-01-01

A method for mounting a mirror for use in a telescope includes attaching the mirror to a plurality of adjustable mounts; determining a distortion in the mirror caused by the plurality adjustable mounts, and, if the distortion is determined to be above a predetermined level: adjusting one or more of the adjustable mounts; and determining the distortion in the mirror caused by the adjustable mounts; and in the event the determined distortion is determined to be at or below the predetermined level, rigidizing the adjustable mounts.

Subduction zone and crustal dynamics of western Washington; a tectonic model for earthquake hazards evaluation

Science.gov (United States)

Stanley, Dal; Villaseñor, Antonio; Benz, Harley

1999-01-01

buttress occurs under the North Cascades region of Washington and under southern Vancouver Island. We find that regional faults zones such as the Devils Mt. and Darrington zones follow the margin of this buttress and the Olympic-Wallowa lineament forms its southern boundary east of the Puget Lowland. Thick, high-velocity, lower-crustal rocks are interpreted to be a mafic/ultramafic wedge occuring just above the subduction thrust. This mafic wedge appears to be jointly deformed with the arch, suggesting strong coupling between the subducting plate and upper plate crust in the Puget Sound region at depths >30 km. Such tectonic coupling is possible if brittle-ductile transition temperatures for mafic/ultramafic rocks on both sides of the thrust are assumed. The deformation models show that dominant north-south compression in the coast ranges of Washington and Oregon is controlled by a highly mafic crust and low heat flow, allowing efficient transmission of margin-parallel shear from Pacific plate interaction with North America. Complex stress patterns which curve around the Puget Sound region require a concentration of northwest-directed shear in the North Cascades of Washington. The preferred model shows that greatest horizontal shortening occurs across the Devils Mt. fault zone and the east end of the Seattle fault.

Greater Vancouver's water supply receives ozone treatment

Energy Technology Data Exchange (ETDEWEB)

Crosby, J.; Singh, I.; Reil, D. D.; Neden, G.

2000-10-01

To improve the overall quality of the treated water delivered to the member municipalities of the Greater Vancouver Water District (GVWD), the GVWD implemented a phased drinking water quality improvement program. The phased treatment program is directed at attaining effective disinfection while minimizing the formation of chlorinated disinfection by-products. Accordingly, the current primary disinfection method of chlorination was reevaluated and an ozone primary disinfection without filtration was authorized. Ozonization provides increased protection against Giardia and Cryptosporidium and a decrease in the formation potential for disinfection by-products (DPBs). This paper describes the design for the ozonation facility at Coquitlam, construction of which began in 1998 and completed during the summer of 2000. The facility houses the liquid oxygen supply, ozone generation, cooling water, ozone injection, primary off-gas ozone destruct system, and provides a home for various office, electrical maintenance and diesel generating functions. The second site at Capilano is expected to start construction in the fall of 2000 and be completed late in 2002. Wit its kilometre long stainless steel ozone contactor and sidestream injector tower, the Coquitlam Ozonation Facility is the first ozone pressure injection system of its kind in North America. 1 tab., 2 figs.

Technical preparation of the Yuzhteploehnergomontazh trust for technological equipment mounting

International Nuclear Information System (INIS)

Zayats, A.I.

1982-01-01

Measures of technical preparation for equipment mounting at the Zaporozhe NPP developed with the Yuzhteploehnergomontazh trust experts are considered. These measures envisage the construction of mounting base of heat facilities, calculation of labour contents and determination of necessary quantity of mounters, development of optimal flowsheet of mounting control, improvement of mounting qualification and creation of stable collective body, improvement of technical level of mounting and welding works, organizational-technical measures on mounting logistics. Factors affecting negatively technical preparation quality of equipment mounting at the Zaporozhe NPP are discussed. The flowsheet of mounting control is presented

Combat vehicle crew helmet-mounted display: next generation high-resolution head-mounted display

Science.gov (United States)

Nelson, Scott A.

1994-06-01

The Combat Vehicle Crew Head-Mounted Display (CVC HMD) program is an ARPA-funded, US Army Natick Research, Development, and Engineering Center monitored effort to develop a high resolution, flat panel HMD for the M1 A2 Abrams main battle tank. CVC HMD is part of the ARPA High Definition Systems (HDS) thrust to develop and integrate small (24 micrometers square pels), high resolution (1280 X 1024 X 6-bit grey scale at 60 frame/sec) active matrix electroluminescent (AMEL) and active matrix liquid crystal displays (AMLCD) for head mounted and projection applications. The Honeywell designed CVC HMD is a next generation head-mounted display system that includes advanced flat panel image sources, advanced digital display driver electronics, high speed (> 1 Gbps) digital interconnect electronics, and light weight, high performance optical and mechanical designs. The resulting dramatic improvements in size, weight, power, and cost have already led to program spin offs for both military and commercial applications.

Experimental High-Resolution Land Surface Prediction System for the Vancouver 2010 Winter Olympic Games

Science.gov (United States)

Belair, S.; Bernier, N.; Tong, L.; Mailhot, J.

2008-05-01

The 2010 Winter Olympic and Paralympic Games will take place in Vancouver, Canada, from 12 to 28 February 2010 and from 12 to 21 March 2010, respectively. In order to provide the best possible guidance achievable with current state-of-the-art science and technology, Environment Canada is currently setting up an experimental numerical prediction system for these special events. This system consists of a 1-km limited-area atmospheric model that will be integrated for 16h, twice a day, with improved microphysics compared with the system currently operational at the Canadian Meteorological Centre. In addition, several new and original tools will be used to adapt and refine predictions near and at the surface. Very high-resolution two-dimensional surface systems, with 100-m and 20-m grid size, will cover the Vancouver Olympic area. Using adaptation methods to improve the forcing from the lower-resolution atmospheric models, these 2D surface models better represent surface processes, and thus lead to better predictions of snow conditions and near-surface air temperature. Based on a similar strategy, a single-point model will be implemented to better predict surface characteristics at each station of an observing network especially installed for the 2010 events. The main advantage of this single-point system is that surface observations are used as forcing for the land surface models, and can even be assimilated (although this is not expected in the first version of this new tool) to improve initial conditions of surface variables such as snow depth and surface temperatures. Another adaptation tool, based on 2D stationnary solutions of a simple dynamical system, will be used to produce near-surface winds on the 100-m grid, coherent with the high- resolution orography. The configuration of the experimental numerical prediction system will be presented at the conference, together with preliminary results for winter 2007-2008.

Where is the hot rock and where is the ground water – Using CSAMT to map beneath and around Mount St. Helens

Science.gov (United States)

Wynn, Jeff; Mosbrucker, Adam; Pierce, Herbert; Spicer, Kurt R.

2016-01-01

We have observed several new features in recent controlled-source audio-frequency magnetotelluric (CSAMT) soundings on and around Mount St. Helens, Washington State, USA. We have identified the approximate location of a strong electrical conductor at the edges of and beneath the 2004–08 dome. We interpret this conductor to be hot brine at the hot-intrusive-cold-rock interface. This contact can be found within 50 meters of the receiver station on Spine 5, which extruded between April and July of 2005. We have also mapped separate regional and glacier-dome aquifers, which lie one atop the other, out to considerable distances from the volcano.

Secular variations of radon in metropolitan Vancouver, British Columbia, Canada

International Nuclear Information System (INIS)

Ghomshei, M.M.; Slawson, W.F.

1990-01-01

In this paper sampling of radon within the soil from three sites in metropolitan Vancouver is reported. Alpha trace bi-weekly measurements during a period of 4 years show secular variations with a period of 8-15 months. There are low-radon and high-radon episodes enduring several months to a year. Average radon level during the high-radon episodes reaches 5-10 times that of the low-radon periods. During high-radon episodes the high-frequency variations show very high amplitudes. After filtering of the high-frequency fluctuations, the data from different sites demonstrate remarkably similar trends. It is suggested that along with hydrogeological events, stress relaxation in rocks, earthquake, and magma emplacement may contribute to the sources of secular variations of radon. Because of long-term variations, radon level in urban areas should be monitored on a continuous basis. Single measurements, even those integrating radiation over a period of few months, may sample a low-radon episode, and provide a false assurance, or occur during a high-radon episode and give a false alarm

Mounting and Alignment of IXO Mirror Segments

Science.gov (United States)

Chan, Kai-Wing; Zhang, William; Evans, Tyler; McClelland, Ryan; Hong, Melinda; Mazzarella, James; Saha, Timo; Jalota, Lalit; Olsen, Lawrence; Byron, Glenn

2010-01-01

A suspension-mounting scheme is developed for the IXO (International X-ray Observatory) mirror segments in which the figure of the mirror segment is preserved in each stage of mounting. The mirror, first fixed on a thermally compatible strongback, is subsequently transported, aligned and transferred onto its mirror housing. In this paper, we shall outline the requirement, approaches, and recent progress of the suspension mount processes.

14 CFR 33.23 - Engine mounting attachments and structure.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Engine mounting attachments and structure... mounting attachments and structure. (a) The maximum allowable limit and ultimate loads for engine mounting attachments and related engine structure must be specified. (b) The engine mounting attachments and related...

76 FR 76689 - Cibola National Forest, Mount Taylor Ranger District, NM, Mount Taylor Combined Exploratory Drilling

Science.gov (United States)

2011-12-08

... National Forest, Mount Taylor Ranger District, NM, Mount Taylor Combined Exploratory Drilling AGENCY... proposed action is to approve two Plans of Operations for exploratory uranium drilling on the Cibola... San Mateo. In total, there are up to 279 drill holes that would be drilled over a period not to exceed...

Mount Ararat, Turkey, Perspective with Landsat Image Overlay

Science.gov (United States)

2004-01-01

This perspective view shows Mount Ararat in easternmost Turkey, which has been the site of several searches for the remains of Noah's Ark. The main peak, known as Great Ararat, is the tallest peak in Turkey, rising to 5165 meters (16,945 feet). This southerly, near horizontal view additionally shows the distinctly conically shaped peak known as 'Little Ararat' on the left. Both peaks are volcanoes that are geologically young, but activity during historic times is uncertain.This image was generated from a Landsat satellite image draped over an elevation model produced by the Shuttle Radar Topography Mission (SRTM). The view uses a 1.25-times vertical exaggeration to enhance topographic expression. Natural colors of the scene are enhanced by image processing, inclusion of some infrared reflectance (as green) to highlight the vegetation pattern, and inclusion of shading of the elevation model to further highlight the topographic features. Volcanoes pose hazards for people, the most obvious being the threat of eruption. But other hazards are associated with volcanoes too. In 1840 an earthquake shook the Mount Ararat region, causing an unstable part of mountain's north slope to tumble into and destroy a village. Visualizations of satellite imagery when combined with elevation models can be used to reveal such hazards leading to disaster prevention through improved land use planning.But the hazards of volcanoes are balanced in part by the benefits they provide. Over geologic time volcanic materials break down to form fertile soils. Cultivation of these soils has fostered and sustained civilizations, as has occurred in the Mount Ararat region. Likewise, tall volcanic peaks often catch precipitation, providing a water supply to those civilizations. Mount Ararat hosts an icefield and set of glaciers, as seen here in this late summer scene, that are part of this beneficial natural processElevation data used in this image was acquired by the Shuttle Radar Topography Mission

Radioisotope Thermoelectric Generator Transporation System licensed hardware second certification test series and package shock mount system test

International Nuclear Information System (INIS)

Ferrell, P.C.; Moody, D.A.

1995-10-01

This paper presents a summary of two separate drop test a e performed in support of the Radioisotope Thermoelectric Generator (RTG) Transportation System (RTGTS). The first portion of this paper presents the second series of drop testing required to demonstrate that the RTG package design meets the requirements of Title 10, Code of Federal Regulations, ''Part 71'' (10 CFR 71). Results of the first test series, performed in July 1994, demonstrated that some design changes were necessary. The package design was modified to improve test performance and the design changes were incorporated into the Safety Analysis Report for Packaging (SARP). The second full-size certification test article (CTA-2) incorporated the modified design and was tested at the US Department of Energy's (DOE) Hanford Site near Richland, Washington. With the successful completion of the test series, and pending DOE Office of Facility Safety Analysis approval of the SARP, a certificate of compliance will be issued for the RTG package allowing its use. The second portion of this paper presents the design and testing of the RTG Package Mount System. The RTG package mount was designed to protect the RTG from excessive vibration during transport, provide shock protection during on/off loading, and provide a mechanism for moving the RTG package with a forklift. Military Standard (MIL-STD) 810E, Transit Drop Procedure (DOE 1989), was used to verify that the shock limiting system limited accelerations in excess of 15 G's at frequencies below 150 Hz. Results of the package mount drop tests indicate that an impact force of 15 G's was not exceeded in any test from a free drop height of 457 mm (18 in.)

Still "at risk": An examination of how street-involved young people understand, experience, and engage with "harm reduction" in Vancouver's inner city.

Science.gov (United States)

Bozinoff, Nikki; Small, Will; Long, Cathy; DeBeck, Kora; Fast, Danya

2017-07-01

Vancouver is an international leader in implementing interventions to reduce harms related to drug use. However, street-involved young people who use drugs continue to be vulnerable to overdose death, hepatitis C (HCV) infection, and high rates of syringe sharing. To better understand this in the context of the intensive public health response, we examined how young people, who are involved in the 'street drug scene', understood, experienced and engaged with harm reduction. Twelve semi-structured interviews were conducted in 2013 with 13 young people (ages 17-28) recruited from the At-Risk Youth Study, a prospective cohort of street-involved and drug-using young people. These interviews were embedded within a larger, eight-year program of ethnographic research and explored participants' understandings of harm reduction, their use of specific services, and their ideas about improving their day-to-day lives. Interviews were transcribed verbatim and a thematic analysis was performed. Young peoples' ideas about harm reduction were diverse and expansive. They articulated the limitations of existing programs, indicating that while they are positioned to reduce the risk of HIV and HCV transmission, they offer little meaningful support to improve young peoples' broader life chances. Young people described strategies to mitigate risk and harm in their own lives, including transitioning to drugs deemed less harmful and attempting to gain access to drug treatment. Finally, young people indicated that spatial considerations (e.g., distance from Vancouver's Downtown Eastside) strongly determined access to services. In Vancouver, a large, well established harm reduction infrastructure seeks to reduce HIV and HCV transmission among street-involved young people. However, young peoples' multiple understandings, experiences and engagements with harm reduction in this setting illustrate the limitations of the existing infrastructure in improving their broader life chances. Copyright

Outdoor brothel culture: the un/making of a transsexual stroll in Vancouver's West End, 1975–1984.

Science.gov (United States)

Ross, Becki

2012-01-01

In the mid-1970s, following a series of police raids on prostitution inside downtown nightclubs, a community of approximately 200 sex workers moved into Vancouver's West End neighborhood, where a small stroll had operated since the early 1970s. This paper examines the contributions made by three male-to-female (MTF) transsexuals of color to the culture of on-street prostitution in the West End. The trans women's stories address themes of fashion, working conditions, money, community formation, violence, and resistance to well-organized anti-prostitution forces. These recollections enable me to bridge and enrich trans history and prostitution history – two fields of inquiry that have under-represented the participation of trans women in the sex industry across the urban West. Acutely familiar with the hazards inherent in a criminalized, stigmatized trade, trans sex workers in the West End manufactured efficacious strategies of harm reduction, income generation, safety planning, and community building. Eschewing the label of “victim”, they leveraged their physical size and style, charisma, contempt towards pimps, earning capacity, and seniority as the first workers on the stroll to assume leadership within the broader constituency of “hookers on Davie Street”. I discover that their short-lived outdoor brothel culture offered only a temporary bulwark against the inevitability of eviction via legal injunction in July 1984, and the subsequent rise in lethal violence against all prostitutes in Vancouver, including MTF transsexuals.

Mounting apparatus for a nozzle guide vane assembly

Science.gov (United States)

Boyd, Gary L.; Shaffer, James E.

1995-01-01

The present invention provides a ceramic nozzle guide assembly with an apparatus for mounting it to a metal nozzle case that includes an intermediate ceramic mounting ring. The mounting ring includes a plurality of projections that are received within a plurality of receptacles formed in the nozzle case. The projections of the mounting ring are secured within the receptacles by a ceramic retainer that allows contact between the two components only along arcuate surfaces thus eliminating sliding contact between the components.

Food and beverage promotions in Vancouver schools: A study of the prevalence and characteristics of in-school advertising, messaging, and signage

Directory of Open Access Journals (Sweden)

Cayley E. Velazquez

2015-01-01

In Vancouver schools, food-related promotions are common and are more prevalent in secondary than elementary schools. Students are regularly exposed to messaging for nutritionally poor items that are not in compliance with provincial school nutrition guidelines and which violate school board advertising policies. Stronger oversight of food-related promotional materials is needed to ensure that schools provide health promoting food environments.

Mounting clips for panel installation

Science.gov (United States)

Cavieres, Andres; Al-Haddad, Tristan; Goodman, Joseph

2017-07-11

A photovoltaic panel mounting clip comprising a base, central indexing tabs, flanges, lateral indexing tabs, and vertical indexing tabs. The mounting clip removably attaches one or more panels to a beam or the like structure, both mechanically and electrically. It provides secure locking of the panels in all directions, while providing guidance in all directions for accurate installation of the panels to the beam or the like structure.

49 CFR 179.10 - Tank mounting.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Tank mounting. 179.10 Section 179.10 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... Design Requirements § 179.10 Tank mounting. (a) The manner in which tanks are attached to the car...

Effect of recycling activities on the heating value of solid waste: case study of the Greater Vancouver Regional District (Metro Vancouver).

Science.gov (United States)

Abedini, Ali R; Atwater, James W; Fu, George Yuzhu

2012-08-01

Two main goals of the integrated solid waste management system (ISWMS) of Metro Vancouver (MV) include further recycling of waste and energy recovery via incineration of waste. These two very common goals, however, are not always compatible enough to fit in an ISWMS depending on waste characteristics and details of recycling programs. This study showed that recent recycling activities in MV have negatively affected the net heating value (NHV) of municipal solid waste (MSW) in this regional district. Results show that meeting MV's goal for additional recycling of MSW by 2015 will further reduce the NHV of waste, if additional recycling activities are solely focused on more extensive recycling of packaging materials (e.g. paper and plastic). It is concluded that 50% additional recycling of paper and plastic in MV will increase the overall recycling rate to 70% (as targeted by the MV for 2015) and result in more than 8% reduction in NHV of MSW. This reduction translates to up to 2.3 million Canadian dollar (CAD$) less revenue at a potential waste-to-energy (WTE) plant with 500 000 tonnes year(-1) capacity. Properly designed recycling programmes, however, can make this functional element of ISWMS compatible with green goals of energy recovery from waste. Herein an explanation of how communities can increase their recycling activities without affecting the feasibility of potential WTE projects is presented.

Ocean floor mounting of wave energy converters

Science.gov (United States)

Siegel, Stefan G

2015-01-20

A system for mounting a set of wave energy converters in the ocean includes a pole attached to a floor of an ocean and a slider mounted on the pole in a manner that permits the slider to move vertically along the pole and rotate about the pole. The wave energy converters can then be mounted on the slider to allow adjustment of the depth and orientation of the wave energy converters.

Housing and Education Partnerships: A Case Study of Vancouver, Washington

Science.gov (United States)

Galvez, Martha; Simington, Jasmine

2015-01-01

The housing and education sectors are being asked to do more with fewer resources. School districts often struggle to meet the needs of low-income students who deal with challenges outside of school and to connect them to resources that can strengthen their academic competencies. Public housing authorities and other assisted-housing providers…

GeoGirls: A Geology and Geophysics Field Camp for Middle School Girls at Mount St. Helens

Science.gov (United States)

Samson, C.; Allstadt, K.; Melander, S.; Groskopf, A.; Driedger, C. L.; Westby, E.

2015-12-01

The August 2015 GeoGirls program was a project designed to inspire girls to gain an appreciation and enthusiasm for Earth sciences using Mount St. Helens as an outdoor volcanic laboratory. Occupations in the field of science and engineering tend to be held by more males than females. One way to address this is to introduce girls to possible opportunities within the geosciences and encourage them to learn more about the dynamic environment in which they live. In 2015, the GeoGirls program sought to accomplish this goal through organizing a five day-long field camp for twenty middle school-aged girls, along with four high school-aged mentors and two local teachers. This group explored Mount St. Helens guided by female scientists from the USGS Cascade Volcano Observatory (CVO), the Mount St. Helens Institute (MSHI), UNAVCO, Boise State, Georgia Tech, University of Washington and Oregon State University. To introduce participants to techniques used by volcanologists, the girls participated in hands-on experiments and research projects focusing on seismology, GPS, terrestrial lidar, photogrammetry, water and tephra. Participants also learned to collect samples, analyze data and use microscopes. Through this experience, participants acquired strategies for conducting research by developing hypotheses, making observations, thinking critically and sharing their findings with others. The success of the GeoGirls program was evaluated by participant and parent survey questionnaires, which allowed assessment of overall enthusiasm and interest in pursuing careers in the geosciences. The program was free to participants and was run jointly by MSHI and CVO and funded by NSF, the American Association of University Women, the Association for Women Geoscientists, the Association of Environmental & Engineering Geologists and private donors. The program will run again in the summer of 2016.

The ecology, status, and conservation of marine and shoreline birds on the west coast of Vancouver Island

International Nuclear Information System (INIS)

Vermeer, K.; Butler, R.W.; Morgan, K.H.

1992-01-01

A symposium was held to combine various disciplines to provide a review of current knowledge about the marine biology of the west coast of Vancouver Island, with a particular emphasis on birds. Papers were presented on the physical and biological environment of the study region, the population and breeding ecology of marine and shoreline birds, the distribution of marine and shoreline birds at sea, the effects of oil pollution on the bird population, and the conservation of marine and shoreline birds. Separate abstracts have been prepared for two papers from this symposium

Washington State Biofuels Industry Development

Energy Technology Data Exchange (ETDEWEB)

Gustafson, Richard [Univ. of Washington, Seattle, WA (United States)

2017-04-09

The funding from this research grant enabled us to design, renovate, and equip laboratories to support University of Washington biofuels research program. The research that is being done with the equipment from this grant will facilitate the establishment of a biofuels industry in the Pacific Northwest and enable the University of Washington to launch a substantial biofuels and bio-based product research program.

"Split Cast Mounting: Review and New Technique".

Science.gov (United States)

Gundawar, S M; Pande, Neelam A; Jaiswal, Priti; Radke, U M

2014-12-01

For the fabrication of a prosthesis, the Prosthodontist meticulously performs all the steps. The laboratory technician then make every effort/strives to perform the remaining lab procedures. However when the processed dentures are remounted on the articulator, some changes are seen. These changes may be divided into two categories: Pre-insertion and post-insertion changes, which deal with the physical properties of the materials involved (Parker, J Prosthet Dent 31:335-342, 1974). Split cast mounting is the method of mounting casts on the articulator. It is essentially a maxillary cast constructed in two parts with a horizontal division. The procedure allows for the verification of the accuracy of the initial mounting and the ease of removal and replacement of the cast. This provides a precise means of correcting the changes in occlusion occurring as a result of the processing technique (Nogueira et al., J Prosthet Dent 91:386-388, 2004). Instability of the split mounting has always been a problem to the Prosthodontist thereby limiting its use. There are various materials mentioned in the literature. The new technique by using Dowel pins and twill thread is very easy, cheaper and simple way to stabilize the split mounting. It is useful and easy in day to day laboratory procedures. The article presents different methods of split cast mounting and the new procedure using easily available materials in prosthetic laboratory.

Research on LQR optimal control method of active engine mount

Science.gov (United States)

Huan, Xie; Yu, Duan

2018-04-01

In this paper, the LQR control method is applied to the active mount of the engine, and a six-cylinder engine excitation model is established. Through the joint simulation of AMESim and MATLAB, the vibration isolation performance of the active mount system and the passive mount system is analyzed. Excited by the multi-engine operation, the simulation results of the vertical displacement, acceleration and dynamic deflection of the vehicle body show that the vibration isolation capability of the active mount system is superior to that of the passive mount system. It shows that compared with the passive mount, LQR active mount can greatly improve the vibration isolation performance, which proves the feasibility and effectiveness of the LQR control method.

Mounting clips for panel installation

Science.gov (United States)

Cavieres, Andres; Al-Haddad, Tristan; Goodman, Joseph; Valdes, Francisco

2017-02-14

An exemplary mounting clip for removably attaching panels to a supporting structure comprises a base, spring locking clips, a lateral flange, a lever flange, and a spring bonding pad. The spring locking clips extend upwardly from the base. The lateral flange extends upwardly from a first side of the base. The lateral flange comprises a slot having an opening configured to receive at least a portion of one of the one or more panels. The lever flange extends outwardly from the lateral flange. The spring bonding flange extends downwardly from the lever flange. At least a portion of the first spring bonding flange comprises a serrated edge for gouging at least a portion of the one or more panels when the one or more panels are attached to the mounting clip to electrically and mechanically couple the one or more panels to the mounting clip.

University of Washington

Data.gov (United States)

Federal Laboratory Consortium — The theme of the University of Washington based Center for Child Environmental Health Risks Research (CHC) is understanding the biochemical, molecular and exposure...

Photoelectric panel with equatorial mounting of drive

Science.gov (United States)

Kukhta, M. S.; Krauinsh, P. Y.; Krauinsh, D. P.; Sokolov, A. P.; Mainy, S. B.

2018-03-01

The relevance of the work is determined by the need to create effective models for sunny energy. The article considers a photoelectric panel equipped with a system for tracking the sun. Efficiency of the system is provided by equatorial mounting, which compensates for the rotation of the Earth by rotating the sunny panel in the plane of the celestial equator. The specificity of climatic and geographical conditions of Tomsk is estimated. The dynamics of power variations of photoelectric panels with equatorial mounting during seasonal fluctuations in Tomsk is calculated. A mobile photovoltaic panel with equatorial mounting of the drive has been developed. The methods of design strategy for placing photovoltaic panels in the architectural environment of the city are presented. Key words: sunny energy, photovoltaics, equatorial mounting, mechatronic model, wave reducer, electric drive.

[The controversy of routine articulator mounting in orthodontics].

Science.gov (United States)

Wang, Li; Han, Xianglong; Bai, Ding

2013-06-01

Articulators have been widely used by clinicians of dentistry. But routine articulator mounting is still controversial in orthodontics. Orthodontists oriented by gnathology approve routine articulator mounting while nongnathologic orthodontists disapprove it. This article reviews the thoughts of orthodontist that they agree or disagree with routine articulator mounting based on the considerations of biting, temporomandibular disorder (TMD), periodontitis, and so on.

The challenges and opportunities of Chinese-language media in Vancouver: A case study of Coast Mountain Publishing & Media Management Corporation

OpenAIRE

Lin, Xiaojun

2018-01-01

This report introduces how Chinese-language media based in Vancouver have experienced ups and downs, and how they seized the moment to dominate their market with the developing and expanding ethnic Chinese group. By taking Coast Mountain Publishing & Media Management Corporation as an example, this report analyses a typical Chinese-language media’s surviving strategies and revenue models in details. Going through the history and observing the existing circumstances closely, this report tr...

Oil spill remote sensing flights around Vancouver Island

Energy Technology Data Exchange (ETDEWEB)

Brown, C.E.; Fingas, M.F.; Marois, R. [Environment Canada, Ottawa, ON (Canada)

2006-07-01

A large number of oiled seabirds are found on beaches and shorelines in Canada each year. Although there are several programs in place to detect high-volume oily bilge dumping incidents, the sensors used in many surveillance procedures are not capable of detecting suspected chronic low-volume disposal of contaminated waste waters by ships. This paper described the development and testing procedures of the Scanning Laser Environmental Airborne Fluorosensor (SLEAF), which was designed to map and characterize oil contamination in marine coastal and shoreline environments. Laser-induced fluorescence is detected by SLEAF with a spectrometric receiver. Full-spectral resolution geo-referenced fluorescence data are collected for each laser pulse and recorded directly to a computer. Eight oil spill remote sensing flights using SLEAF were conducted during March and April 2006. Geo-referenced infrared, ultraviolet, colour video and digital still imagery was collected alongside the fluorosensor data. Several light patches of oil were observed with SLEAF, most of which were in shipping lanes in the Strait of Juan de Fuca. The oil patches were light, and some were not visible to the naked eye, and were only detected by the laser fluorosensor. Larger slicks were captured in video imagery. Approximately 50 marine vessels were overflown during the flight demonstration program, and only 2 vessels appeared to be associated with the oil slicks. It was concluded that chronic low-volume oil releases in shipping lanes around Vancouver Island are a cause for concern. 11 refs., 2 tabs., 5 figs.

Development of a Double Glass Mounting Method Using Formaldehyde Alcohol Azocarmine Lactophenol (FAAL) and its Evaluation for Permanent Mounting of Small Nematodes.

Science.gov (United States)

Zahabiun, Farzaneh; Sadjjadi, Seyed Mahmoud; Esfandiari, Farideh

2015-01-01

Permanent slide preparation of nematodes especially small ones is time consuming, difficult and they become scarious margins. Regarding this problem, a modified double glass mounting method was developed and compared with classic method. A total of 209 nematode samples from human and animal origin were fixed and stained with Formaldehyde Alcohol Azocarmine Lactophenol (FAAL) followed by double glass mounting and classic dehydration method using Canada balsam as their mounting media. The slides were evaluated in different dates and times, more than four years. Different photos were made with different magnification during the evaluation time. The double glass mounting method was stable during this time and comparable with classic method. There were no changes in morphologic structures of nematodes using double glass mounting method with well-defined and clear differentiation between different organs of nematodes in this method. Using this method is cost effective and fast for mounting of small nematodes comparing to classic method.

Washington Tsunami Hazard Mitigation Program

Science.gov (United States)

Walsh, T. J.; Schelling, J.

2012-12-01

Washington State has participated in the National Tsunami Hazard Mitigation Program (NTHMP) since its inception in 1995. We have participated in the tsunami inundation hazard mapping, evacuation planning, education, and outreach efforts that generally characterize the NTHMP efforts. We have also investigated hazards of significant interest to the Pacific Northwest. The hazard from locally generated earthquakes on the Cascadia subduction zone, which threatens tsunami inundation in less than hour following a magnitude 9 earthquake, creates special problems for low-lying accretionary shoreforms in Washington, such as the spits of Long Beach and Ocean Shores, where high ground is not accessible within the limited time available for evacuation. To ameliorate this problem, we convened a panel of the Applied Technology Council to develop guidelines for construction of facilities for vertical evacuation from tsunamis, published as FEMA 646, now incorporated in the International Building Code as Appendix M. We followed this with a program called Project Safe Haven (http://www.facebook.com/ProjectSafeHaven) to site such facilities along the Washington coast in appropriate locations and appropriate designs to blend with the local communities, as chosen by the citizens. This has now been completed for the entire outer coast of Washington. In conjunction with this effort, we have evaluated the potential for earthquake-induced ground failures in and near tsunami hazard zones to help develop cost estimates for these structures and to establish appropriate tsunami evacuation routes and evacuation assembly areas that are likely to to be available after a major subduction zone earthquake. We intend to continue these geotechnical evaluations for all tsunami hazard zones in Washington.

Improved resolution by mounting of tissue sections for laser microdissection.

Science.gov (United States)

van Dijk, M C R F; Rombout, P D M; Dijkman, H B P M; Ruiter, D J; Bernsen, M R

2003-08-01

Laser microbeam microdissection has greatly facilitated the procurement of specific cell populations from tissue sections. However, the fact that a coverslip is not used means that the morphology of the tissue sections is often poor. To develop a mounting method that greatly improves the morphological quality of tissue sections for laser microbeam microdissection purposes so that the identification of target cells can be facilitated. Fresh frozen tissue and formalin fixed, paraffin wax embedded tissue specimens were used to test the morphological quality of mounted and unmounted tissue. The mounting solution consisted of an adhesive gum and blue ink diluted in water. Interference of the mounting solution with DNA quality was analysed by the polymerase chain reaction using 10-2000 cells isolated by microdissection from mounted and unmounted tissue. The mounting solution greatly improved the morphology of tissue sections for laser microdissection purposes and had no detrimental effects on the isolation and efficiency of amplification of DNA. One disadvantage was that the mounting solution reduced the cutting efficiency of the ultraviolet laser. To minimise this effect, the mounting solution should be diluted as much as possible. Furthermore, the addition of blue ink to the mounting medium restores the cutting efficiency of the laser. The mounting solution is easy to prepare and apply and can be combined with various staining methods without compromising the quality of the DNA extracted.

Rapid, low-cost photogrammetry to monitor volcanic eruptions: an example from Mount St. Helens, Washington, USA

Science.gov (United States)

Diefenbach, Angela K.; Crider, Juliet G.; Schilling, Steve P.; Dzurisin, Daniel

2012-01-01

We describe a low-cost application of digital photogrammetry using commercially available photogrammetric software and oblique photographs taken with an off-the-shelf digital camera to create sequential digital elevation models (DEMs) of a lava dome that grew during the 2004–2008 eruption of Mount St. Helens (MSH) volcano. Renewed activity at MSH provided an opportunity to devise and test this method, because it could be validated against other observations of this well-monitored volcano. The datasets consist of oblique aerial photographs (snapshots) taken from a helicopter using a digital single-lens reflex camera. Twelve sets of overlapping digital images of the dome taken during 2004–2007 were used to produce DEMs and to calculate lava dome volumes and extrusion rates. Analyses of the digital images were carried out using photogrammetric software to produce three-dimensional coordinates of points identified in multiple photos. The evolving morphology of the dome was modeled by comparing successive DEMs. Results were validated by comparison to volume measurements derived from traditional vertical photogrammetric surveys by the US Geological Survey Cascades Volcano Observatory. Our technique was significantly less expensive and required less time than traditional vertical photogrammetric techniques; yet, it consistently yielded volume estimates within 5% of the traditional method. This technique provides an inexpensive, rapid assessment tool for tracking lava dome growth or other topographic changes at restless volcanoes.

Large-scale magnetic field perturbation arising from the 18 May 1980 eruption from Mount St. Helens, Washington

Science.gov (United States)

Mueller, R.J.; Johnston, M.J.S.

1989-01-01

A traveling magnetic field disturbance generated by the 18 may 1980 eruption of Mount St. Helens at 1532 UT was detected on an 800-km linear array of recording magnetometers installed along the San Andreas fault system in California, from San Francisco to the Salton Sea. Arrival times of the disturbance field, from the most northern of these 24 magnetometers (996 km south of the volcano) to the most southern (1493 km S23?? E), are consistent with the generation of a traveling ionospheric disturbance stimulated by the blast pressure wave in the atmosphere. The first arrivals at the north and the south ends of the array occurred at 26 and 48 min, respectively, after the initial eruption. Apparent average wave velocity through the array is 309 ?? 14 m s-1 but may have approached 600 m s-1 close to the volcano. The horizontal phase and the group velocity of ??? 300 m s-1 at periods of 70-80 min, and the attenuation with distance, strongly suggest that the magnetic field perturbations at distances of 1000-1500 km are caused by gravity mode acoustic-gravity waves propagating at F-region heights in the ionosphere. ?? 1989.

Declaraciones del Comité Internacional de Directores de Revistas Médicas anexas a las normas de Vancouver Statements issued by the International Committee of Medical Journal Editors in conjunction with the Vancouver standards

Directory of Open Access Journals (Sweden)

1998-04-01

Full Text Available Estas declaraciones, emitidas por el Comité de Directores de Revistas Médicas como publicación anexa a las normas de Vancouver, abarcan temas relacionados con algunos aspectos legales, éticos y prácticos de la publicación de trabajos de investigación, y de los comentarios que estos suscitan, en revistas biomédicas. Partiendo de la definición de lo que constituye una revista sometida a arbitraje científico, se describen las funciones de los propietarios y directores de revistas y de los miembros de una junta editorial y se establecen normas de conducta en casos de conflictos de intereses, retractaciones o correcciones, fraude y violaciones de la confidencialidad. Por último se exploran, entre otros temas, los problemas que encierra la divulgación de los resultados de investigaciones por los medios de comunicación de masas, la inclusión de material propagandístico en la revista y la aceptación simultánea de manuscritos cuyos autores llegan a conclusiones divergentes sobre los resultados de una misma investigación.These statements, which are published by the International Committee of Medical Journal Editors in conjunction with the Vancouver standards, cover some of the legal, ethical, and practical aspects of the publication of research papers, and of the comments generated by them, in biomedical journals. Following a definition of what constitutes a peer-reviewed journal, the roles of journal owners and editors are described, along with those of members of an editorial board, and procedural norms are set forth in connection with conflicts of interests, retractions or corrections, fraud, and breaches of confidentiality. Among the last topics explored are the problems involved in the dissemination of research results by the popular media, the handling of advertising within the journal, and the simultaneous acceptance of manuscripts whose authors have arrived at opposite conclusions regarding the results of a particular study.

Impact of the Vancouver Island natural gas pipeline construction on water quality: Project report

Energy Technology Data Exchange (ETDEWEB)

Li, G

1993-01-01

Prior to the construction of the Vancouver Island natural gas pipeline, concern was expressed for the potential defilement of community domestic water supplies when the construction work occurred in community watersheds. When drinking water becomes turbid from rainfall runoff passing through construction sites, the community disinfection process is rendered inefficacious. At a specified turbidity level, the water becomes too risky to drink without alternative disinfection such as boiling. This situation creates significant administrative problems for local health officials, intolerable social problems for residents and processing problems for industries which require clean water. This document is a review of the weekly environmental surveillance reports submitted by D. Tripp Biological Consultants to the B.C. Utilities Commission. The material is organized to relate construction practices with weather patterns thereby showing the resultant effects on water quality (turbidity).

Isolation Mounting for Charge-Coupled Devices

Science.gov (United States)

Goss, W. C.; Salomon, P. M.

1985-01-01

CCD's suspended by wires under tension. Remote thermoelectric cooling of charge coupled device allows vibration isolating mounting of CCD assembly alone, without having to suspend entire mass and bulk of thermoelectric module. Mounting hardware simple and light. Developed for charge-coupled devices (CCD's) in infrared telescope support adaptable to sensors in variety of environments, e.g., sensors in nuclear reactors, engine exhausts and plasma chambers.

Flow distortion on boom mounted cup anemometers

DEFF Research Database (Denmark)

Lindelöw, Per Jonas Petter; Friis Pedersen, Troels; Gottschall, Julia

In this report we investigate on wind direction dependent errors in the measurement of the horizontal wind speed by boom mounted cup anemometers. The boom mounting on the studied lattice tower is performed according to IEC standard design rules, yet, larger deviations than predicted by flow models...... are observed. The errors on the measurements are likely caused by an underestimation of the flow distortions around the tower. In this paper an experimental method for deriving a correction formula and an in-field calibration is suggested. The method is based on measurements with two cup anemometers mounted...

Transducer-Mounting Fixture

Science.gov (United States)

Spiegel, Kirk W.

1990-01-01

Transducer-mounting fixture holds transducer securely against stud. Projects only slightly beyond stud after installation. Flanged transducer fits into fixture when hinged halves open. When halves reclosed, fixture tightened onto threaded stud until stud makes contact with transducer. Knurled area on fixture aids in tightening fixture on stud.

49 CFR 571.212 - Standard No. 212; Windshield mounting.

Science.gov (United States)

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Standard No. 212; Windshield mounting. 571.212... Motor Vehicle Safety Standards § 571.212 Standard No. 212; Windshield mounting. S1. Scope. This standard..., under the conditions of S6, the windshield mounting of the vehicle shall retain not less than the...

New active machine tool drive mounting on the frame

Directory of Open Access Journals (Sweden)

Švéda J.

2007-10-01

Full Text Available The paper deals with the new active mounting of the machine tool drives. The commonly used machine tools are at this time mainly equipped with fix-mounting of the feed drives. This structure causes full transmission of the force shocks to the machine bed and thereby restricts the dynamic properties of the motion axis and the whole machine. The spring-mounting of the feed drives is one of the possibilities how to partially suppress the vibrations. The force that reacts to the machine tool bed is transformed thereby the vibrations are lightly reduced. Unfortunately the transformation is not fully controlled. The new active mounting of the machine tool drives allows to fully control the force behaviour that react to the machine body. Thereby the number of excited frequencies on the machine tool bed is significantly reduced. The active variant of the feed drive mounting is characterized by the synergistic cooperation between two series-connected actuators (“motor on motor”. The paper briefly describes design, control techniques and optimization of the feed drives with the new active mounting conception.

Science of Nowcasting Olympic Weather for Vancouver 2010 (SNOW-V10): a World Weather Research Programme Project

Science.gov (United States)

Isaac, G. A.; Joe, P. I.; Mailhot, J.; Bailey, M.; Bélair, S.; Boudala, F. S.; Brugman, M.; Campos, E.; Carpenter, R. L.; Crawford, R. W.; Cober, S. G.; Denis, B.; Doyle, C.; Reeves, H. D.; Gultepe, I.; Haiden, T.; Heckman, I.; Huang, L. X.; Milbrandt, J. A.; Mo, R.; Rasmussen, R. M.; Smith, T.; Stewart, R. E.; Wang, D.; Wilson, L. J.

2014-01-01

A World Weather Research Programme (WWRP) project entitled the Science of Nowcasting Olympic Weather for Vancouver 2010 (SNOW-V10) was developed to be associated with the Vancouver 2010 Olympic and Paralympic Winter Games conducted between 12 February and 21 March 2010. The SNOW-V10 international team augmented the instrumentation associated with the Winter Games and several new numerical weather forecasting and nowcasting models were added. Both the additional observational and model data were available to the forecasters in real time. This was an excellent opportunity to demonstrate existing capability in nowcasting and to develop better techniques for short term (0-6 h) nowcasts of winter weather in complex terrain. Better techniques to forecast visibility, low cloud, wind gusts, precipitation rate and type were evaluated. The weather during the games was exceptionally variable with many periods of low visibility, low ceilings and precipitation in the form of both snow and rain. The data collected should improve our understanding of many physical phenomena such as the diabatic effects due to melting snow, wind flow around and over terrain, diurnal flow reversal in valleys associated with daytime heating, and precipitation reductions and increases due to local terrain. Many studies related to these phenomena are described in the Special Issue on SNOW-V10 for which this paper was written. Numerical weather prediction and nowcast models have been evaluated against the unique observational data set now available. It is anticipated that the data set and the knowledge learned as a result of SNOW-V10 will become a resource for other World Meteorological Organization member states who are interested in improving forecasts of winter weather.

Organization and processes of the BN-600 reactor mounting

International Nuclear Information System (INIS)

Dubrovin, E.Z.; Karpenko, V.N.; Takhtaulov, V.M.

1982-01-01

Structural peculiarities of the BN-600 reactor plant are considered. Experience of metal structure mounting inside the reactor vessel has been analysed. Recommendations on the improvements on the organization of the thermal mechanical equipment mounting are given. It is concluded that the consideration of these recommendations will permit to reduce expenditures of labour by 10-40% for the mounting

46 CFR 61.05-15 - Boiler mountings and attachments.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Boiler mountings and attachments. 61.05-15 Section 61.05... TESTS AND INSPECTIONS Tests and Inspections of Boilers § 61.05-15 Boiler mountings and attachments. (a....05-10. (b) Each stud or bolt for each boiler mounting that paragraph (c) of this section requires to...

Tourism, Tolerance, or Hospitality? An Assessment of a Native/Non-Native, Urban/Rural Youth Exchange Program between Fort Good Hope, NWT, and East Vancouver, BC

Science.gov (United States)

Hern, Matt

2009-01-01

This article considers and assesses a youth exchange project between two community-based youth centers: The Purple Thistle Centre in East Vancouver, British Columbia, and the K'asho Got'ine Youth Centre in Fort Good Hope, Northwest Territories. Both centers serve primarily low-income youth, but after that the similarities are very few. The…

Linear and/or curvilinear rail mount system

Science.gov (United States)

Thomas, Jackie D. (Inventor); Harris, Lawanna L. (Inventor)

2012-01-01

One or more linear and/or curvilinear mounting rails are coupled to a structure. Each mounting rail defines a channel and at least one cartridge assembly is engaged in the channel. Each cartridge assembly includes a housing that slides within the channel. The housing defines a curvilinearly-shaped recess longitudinally aligned with the channel when the housing is in engagement therewith. The cartridge assembly also includes a cleat fitted in the recess for sliding engagement therealong. The cleat can be coupled to a fastener that passes through the mounting rail and the housing when the housing is so-engaged in the channel. The cleat is positioned in the recess by a position of the fastener.

Greater Vancouver regional district air quality management plan : implementation status report

International Nuclear Information System (INIS)

2001-03-01

In December 1994, an Air Quality Management Plan (AQMP) was adopted by the Greater Vancouver Regional District. The AQMP included ways to improve air quality in the region, leading to reduced emissions from commercial and industrial operations. This Plan encourages cooperation with the various communities affected to achieve clean air lifestyles and manage emissions from human activity to enhance human health and the integrity of the environment. The reduction of total emissions of the common air contaminants sulphur and nitrogen oxides, particulate matter, carbon monoxide and volatile organic compounds by 38 per cent is the stated aim of the AQMP. Five years of planning resulted in the formulation of the AQMP. The issues addressed were assigned one of four priorities as follows: priority 1 deals with ground level ozone and fine particulate, priority 2 looks at visibility, hazardous air pollutants, and global climate change, priority 3 concerns odour, carbon monoxide, sulphur dioxide, acidic deposition, and nitrogen dioxide, and priority 4 contains total suspended particulate matter and volatile organic compounds. A total of 54 Emission Reduction Measures were established, and the document reviewed them. Progress is being made in all areas. 2 tabs., 3 figs

Gay Men's Understanding and Education of New HIV Prevention Technologies in Vancouver, Canada.

Science.gov (United States)

Klassen, Benjamin J; Lachowsky, Nathan J; Lin, Sally Yue; Edward, Joshua B; Chown, Sarah A; Hogg, Robert S; Moore, David M; Roth, Eric A

2017-10-01

Effective rollout of HIV treatment-based prevention such as pre-exposure prophylaxis and treatment as prevention has been hampered by poor education, limited acceptability, and stigma among gay men. We undertook a thematic analysis regarding the education sources and acceptability of these New Prevention Technologies (NPTs) using 15 semistructured interviews with gay men in Vancouver, Canada, who were early adopters of NPTs. NPT education was derived from a variety of sources, including the Internet, health care providers, community organizations, sexual partners, and peers; participants also emphasized their own capacities as learners and educators. Acceptable forms of NPT education featured high-quality factual information, personal testimony, and easy access. Stigma was highlighted as a major barrier. For public health, policy makers, and gay communities to optimize the personal and population benefits of NPTs, there is a need for increased community support and dialogue, antistigma efforts, early NPT adopter testimony, and personalized implementation strategies.

Methods and apparatus for radially compliant component mounting

Science.gov (United States)

Bulman, David Edward [Cincinnati, OH; Darkins, Jr., Toby George; Stumpf, James Anthony [Columbus, IN; Schroder, Mark S [Greenville, SC; Lipinski, John Joseph [Simpsonville, SC

2012-03-27

Methods and apparatus for a mounting assembly for a liner of a gas turbine engine combustor are provided. The combustor includes a combustor liner and a radially outer annular flow sleeve. The mounting assembly includes an inner ring surrounding a radially outer surface of the liner and including a plurality of axially extending fingers. The mounting assembly also includes a radially outer ring coupled to the inner ring through a plurality of spacers that extend radially from a radially outer surface of the inner ring to the outer ring.

Vertical repositioning accuracy of magnetic mounting systems on 4 articulator models.

Science.gov (United States)

Lee, Wonsup; Kwon, Ho-Beom

2018-03-01

Research of the ability of a cast mounted on an articulator on maintaining the identical position of a cast mounted on an articulator after repeated repositioning is lacking, despite the possible effects this may have on the occlusion of a mounted cast. The purpose of this in vitro study was to verify and compare the vertical repositioning accuracy of 4 different, commercially available articulator magnetic mounting plate systems. Four articulators and their associated magnetic mounting plates were selected for the study. These were the Artex AR articulator (Amann Girrbach AG), the Denar Mark II articulator (Whip Mix Corp), the Kavo Protar Evo articulator (Kavo Dental GmbH), and the SAM3 articulator (SAM Präzisionstechnik GmbH). Three new magnetic mounting plates were prepared for each articulator system. The repositioning accuracy of each mounting plate was evaluated by comparing the standard deviation of the vertical distances measured between the mounting plate and a laser displacement sensor. The lower arm of the articulator was secured, and the vertical distance was measured by positioning the laser displacement sensor positioned vertically above the mounting plate. Once the vertical distance was measured, the mounting plate was detached from the articulator and reattached manually to prepare for the next measurement. This procedure was repeated 30 times for each of the 3 magnetic mounting plates. Data were analyzed by ANOVA for 2-stage nested design and the Levene test (α=.05). Significant differences were detected among articulator systems and between magnetic mounting plates of the same type. The standard deviations of the measurements made with the Artex AR articulator, Denar Mark II articulator, Kavo Protar Evo articulator, and SAM3 articulator were 0.0027, 0.0308, 0.0214, and 0.0215 mm, respectively. Thus, the repositioning accuracy could be ranked in the order as follows: Artex AR, Kavo Protar Evo, SAM3, and Denar Mark II. The position of the

Temperature profiles from MBT casts from the VANCOUVER from Ocean Weather Station P (OWS-P) in the North Pacific Ocean from 30 October to 1968-12-01 (NODC Accession 6900711)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Bathythermograph data were collected from the VANCOUVER within a 1-mile radius of Ocean Weather Station P (5000N 14500W) and in transit. Data were collected by the...

Internally Mounting Strain Gages

Science.gov (United States)

Jett, J. R., Jr.

1984-01-01

Technique for mounting strain gages inside bolt or cylinder simultaneously inserts gage, attached dowel segment, and length of expandable tubing. Expandable tubing holds gage in place while adhesive cures, assuring even distribution of pressure on gage and area gaged.

Geothermal segmentation of the Cascade Range in the USA

Science.gov (United States)

Guffanti, Marianne; Muffler, L.J.; Mariner, R.H.; Sherrod, D.R.; Smith, James G.; Blackwell, D.D.; Weaver, C.S.

1990-01-01

Characteristics of the crustal thermal regime of the Quaternary Cascades vary systematically along the range. Spatially congruent changes in volcanic vent distribution, volcanic extrusion rate, hydrothermal discharge rate, and regional conductive heat flow define 5 geothermal segments. These segments are, from north to south: (1) the Washington Cascades north of Mount Rainier, (2) the Cascades from Mount Rainier to Mount Hood, (3) the Oregon Cascades from south of Mount Hood to the California border, (4) northernmost California, including Mount Shasta and Medicine Lake volcano, and (5) the Lassen region of northern California. This segmentation indicates that geothermal resource potential is not uniform in the Cascade Range. Potential varies from high in parts of Oregon to low in Washington north of Mount Rainier.

Application of Evolutionary Computation in Automotive Powertrain Mount Tuning

Directory of Open Access Journals (Sweden)

Anab Akanda

2006-01-01

Full Text Available Engine mount tuning is a multi-disciplinary exercise since it affects Idle-shake, Road-shake and power-train noise response. Engine inertia is often used as a tuned absorber for controlling suspension resonance related road-shake issues. Last but not least, vehicle ride and handling may also be affected by mount tuning. In this work, Torque-Roll-Axis (TRA decoupling of the rigid powertrain was used as a starting point for mount tuning. Nodal point of flexible powertrain bending was used to define the envelop for transmission mount locations. The frequency corresponding to the decoupled roll mode of the rigid powertrain was then adjusted for idle-shake and road-shake response management.

Father Secchi Goes to Washington

Science.gov (United States)

McCarthy, M. F.

1994-12-01

In 1848 a small group of Jesuit refugees arrived at Georgetown College near Washington, D.C. Among them was a young priest, Angelo Secchi, who had finished theology studies in Rome, but had not been able to complete his final examinations. This done successfully, Secchi turned to astronomy and the new facilities of the Georgetown College Observatory, directed by its founder, Fr. James Curley. During his two years in Washington, Secchi studied physics, wrote an article on Electrical Rheometry for the Smithsonian Institution, and formed a friendship with Matthew Fontaine Maury of the U.S. Navy, who headed the Chart Service and in 1844 was named superintendent of the National Observatory. This was later named the U.S. Naval Observatory. Secchi's friendships formed during the Washington visit proved most helpful for relations between European astronomers and U.S. colleagues. Secchi, after his return to Rome constructed the Observatory of the Collegio Romano atop the baroque Church of St. Ignatius in Rome and began his work in spectral classification of stars.

Corrections Education. Washington's Community and Technical Colleges

Science.gov (United States)

Washington State Board for Community and Technical Colleges, 2015

2015-01-01

The Washington State Department of Corrections contracts with community colleges to provide basic education and job training at each of the state's 12 adult prisons so upon release, individuals are more likely to get jobs and less likely to return. Washington State community colleges build a bridge for offenders to successfully re-enter…

Aerospace Training. Washington's Community and Technical Colleges

Science.gov (United States)

Washington State Board for Community and Technical Colleges, 2014

2014-01-01

Aerospace is an economic powerhouse that generates jobs and fuels our economy. Washington's community and technical colleges produce the world-class employees needed to keep it that way. With about 1,250 aerospace-related firms employing more than 94,000 workers, Washington has the largest concentration of aerospace expertise in the nation. To…

76 FR 16323 - Irish Potatoes Grown in Washington; Continuance Referendum

Science.gov (United States)

2011-03-23

...; FV11-946-1 CR] Irish Potatoes Grown in Washington; Continuance Referendum AGENCY: Agricultural... conducted among eligible Washington potato growers to determine whether they favor continuance of the marketing order regulating the handling of Irish potatoes grown in Washington. DATES: The referendum will be...

Flat mount preparation for observation and analysis of zebrafish embryo specimens stained by whole mount in situ hybridization.

Science.gov (United States)

Cheng, Christina N; Li, Yue; Marra, Amanda N; Verdun, Valerie; Wingert, Rebecca A

2014-07-17

The zebrafish embryo is now commonly used for basic and biomedical research to investigate the genetic control of developmental processes and to model congenital abnormalities. During the first day of life, the zebrafish embryo progresses through many developmental stages including fertilization, cleavage, gastrulation, segmentation, and the organogenesis of structures such as the kidney, heart, and central nervous system. The anatomy of a young zebrafish embryo presents several challenges for the visualization and analysis of the tissues involved in many of these events because the embryo develops in association with a round yolk mass. Thus, for accurate analysis and imaging of experimental phenotypes in fixed embryonic specimens between the tailbud and 20 somite stage (10 and 19 hours post fertilization (hpf), respectively), such as those stained using whole mount in situ hybridization (WISH), it is often desirable to remove the embryo from the yolk ball and to position it flat on a glass slide. However, performing a flat mount procedure can be tedious. Therefore, successful and efficient flat mount preparation is greatly facilitated through the visual demonstration of the dissection technique, and also helped by using reagents that assist in optimal tissue handling. Here, we provide our WISH protocol for one or two-color detection of gene expression in the zebrafish embryo, and demonstrate how the flat mounting procedure can be performed on this example of a stained fixed specimen. This flat mounting protocol is broadly applicable to the study of many embryonic structures that emerge during early zebrafish development, and can be implemented in conjunction with other staining methods performed on fixed embryo samples.

Millimeter-Wave Radar Field Measurements and Inversion of Cloud Parameters for the 1999 Mt. Washington Icing Sensors Project

Science.gov (United States)

Pazmany, Andrew L.; Reehorst, Andrew (Technical Monitor)

2001-01-01

The Mount Washington Icing Sensors Project (MWISP) was a multi-investigator experiment with participants from Quadrant Engineering, NOAA Environmental Technology Laboratory (NOAA/ETL), the Microwave Remote Sensing Laboratory (MIRSL) of the University of Massachusetts (UMass), and others. Radar systems from UMass and NOAA/ETL were used to measure X-, Ka-, and W-band backscatter data from the base of Mt. Washington, while simultaneous in-situ particle measurements were made from aircraft and from the observatory at the summit. This report presents range and time profiles of liquid water content and particle size parameters derived from range profiles of radar reflectivity as measured at X-, Ka-, and W-band (9.3, 33.1, and 94.9 GHz) using an artificial neural network inversion algorithm. In this report, we provide a brief description of the experiment configuration, radar systems, and a review of the artificial neural network used to extract cloud parameters from the radar data. Time histories of liquid water content (LWC), mean volume diameter (MVD) and mean Z diameter (MZD) are plotted at 300 m range intervals for slant ranges between 1.1 and 4 km. Appendix A provides details on the extraction of radar reflectivity from measured radar power, and Appendix B provides summary logs of the weather conditions for each day in which we processed data.

Surviving the housing crisis: Social violence and the production of evictions among women who use drugs in Vancouver, Canada.

Science.gov (United States)

Collins, Alexandra B; Boyd, Jade; Damon, Will; Czechaczek, Sandra; Krüsi, Andrea; Cooper, Hannah; McNeil, Ryan

2018-04-11

Single room accommodation (SRA) housing is among the only forms of accessible housing to marginalized women who use illicit drugs in many urban settings. However, SRA housing environments may create specific health and drug risks for women. Little research has examined the gendered mechanisms contributing to housing vulnerability for women who use drugs and the subsequent ways they aim to mitigate harm. This study examines the gendered vulnerabilities to, and harms stemming from, evictions from SRAs in Vancouver, Canada. Qualitative interviews were conducted with 56 people who use drugs who were recently evicted (past 60 days) from SRAs in Vancouver's Downtown Eastside neighbourhood, 19 of whom identified as women which informed this analysis. Participants were recruited by Peer Researcher Assistants for baseline and follow-up interviews three to six months later. Interview transcripts were analyzed thematically and interpreted by drawing on concepts of social violence. Findings underscore how gendered violence and forms of social control operationalized within SRAs normalized violence against women and restricted their agency. Surveillance mechanisms increased women's experiences of violence as they sought to evade such interventions. Post-eviction, women faced pronounced vulnerability to harm which reinforced their social and spatial marginality within a drug scene. Collectively, women's experiences within SRAs highlight how the hybrid forms of disciplinary mechanisms used within these housing environments significantly impacted women's experiences of harm. Greater attention to the impacts of housing and building policies on women who use drugs is needed to better address the morbidity and mortality of this population. Copyright © 2018 Elsevier Ltd. All rights reserved.

UHV mirror mounts for photophysics beamline at Indus-I

International Nuclear Information System (INIS)

Meenakshi Raja Rao, P.; Bhattacharya, S.S.; Das, N.C.; Rajasekhar, B.N.; Roy, A.P.

1995-01-01

Photophysics beamline makes use of a combination of two toroidal mirrors and one meter Seya-Namioka Monochromator in its fore optics. The fore optics monochromatises and steers the synchrotron radiation source (SRS) beam from its tangent point to the sample situated at a distance of about five meters. Slit widths of the monochromator are of the order of 100μ and the sample size is one mm 2 . Hence it is essential to impart precision rotational and translational movements of the same order of magnitude to the mirrors with the use of appropriate mirror mounts. Since Indus-1 operates at a pressure -9 mbar, the mirror mounts should be UHV compatible and the movements should be actuated under UHV. The mirrors along with the mirror mounts are enclosed in UHV chambers. The mirror chambers have been fabricated at Centre for Advanced Technology (CAT) workshops and tested up to a pressure of 10 -9 mbar. The mirror mounts are designed, fabricated and leak checked (He leak rate -10 std cc/s) The precision movements are achieved with the help of bellow sealed shaft mechanism and adjustable screws provided with the kinematic mount of the mirror frame. The performance of the mirror mount was tested at atmospheric pressure by using a laser beam and found to be good. The minimum displacement of the laser beam at slit and sample positions is ∼ 70μ which is quite adequate for optical alignment. The performance of the mirror mount under UHV conditions is being evaluated. (author). 4 refs., 3 figs

75 FR 14462 - Notice of Inventory Completion: Central Washington University, Department of Anthropology...

Science.gov (United States)

2010-03-25

... Washington University, Department of Anthropology, Ellensburg, WA, and Thomas Burke Memorial Washington State... Washington University, Department of Anthropology, Ellensburg, WA, and the Thomas Burke Memorial Washington... Anthropology, Central Washington University, Ellensburg, WA 98926-7544, telephone (509) 963-2671 or Dr. Peter...

Jim Peters' collapse in the 1954 Vancouver Empire Games marathon.

Science.gov (United States)

Noakes, Tim; Mekler, Jackie; Pedoe, Dan Tunstall

2008-08-01

On 7 August 1954, the world 42 km marathon record holder, Jim Peters, collapsed repeatedly during the final 385 metres of the British Empire and Commonwealth Games marathon held in Vancouver, Canada. It has been assumed that Peters collapsed from heatstroke because he ran too fast and did not drink during the race, which was held in windless, cloudless conditions with a dry-bulb temperature of 28 degrees C. Hospital records made available to us indicate that Peters might not have suffered from exertional heatstroke, which classically produces a rectal temperature > 42 degrees C, cerebral effects and, usually, a fatal outcome without vigorous active cooling. Although Peters was unconscious on admission to hospital approximately 60 minutes after he was removed from the race, his rectal temperature was 39.4 degrees C and he recovered fully, even though he was managed conservatively and not actively cooled. We propose that Peters' collapse was more likely due to a combination of hyperthermia-induced fatigue which caused him to stop running; exercise-associated postural hypotension as a result of a low peripheral vascular resistance immediately he stopped running; and combined cerebral effects of hyperthermia, hypertonic hypernatraemia associated with dehydration, and perhaps undiagnosed hypoglycaemia. But none of these conditions should cause prolonged unconsciousness, raising the possibility that Peters might have suffered from a transient encephalopathy, the exact nature of which is not understood.

Temperature profiles from MBT casts from the VANCOUVER from Ocean Weather Station P (OWS-P) in the North Pacific Ocean from 1967-12-10 to 1968-01-13 (NODC Accession 6900710)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Bathythermograph data were collected from the VANCOUVER within a 1-mile radius of Ocean Weather Station P (5000N 14500W) and in transit. Data were collected by the...

76 FR 377 - Land Acquisitions; Cowlitz Indian Tribe of Washington

Science.gov (United States)

2011-01-04

... State of Washington by Auditor's File Nos. G 450664 and G 147358. Parcel II That portion of the... thereof acquired by the State of Washington by deed recorded under Auditor's File Nos. G 140380 and D... recorded under Auditor's File No. F 38759, records of Clark County, Washington, described as follows...

Hall Current Plasma Source Having a Center-Mounted or a Surface-Mounted Cathode

Science.gov (United States)

Martinez, Rafael A. (Inventor); Williams, John D. (Inventor); Moritz, Jr., Joel A. (Inventor); Farnell, Casey C. (Inventor)

2018-01-01

A miniature Hall current plasma source apparatus having magnetic shielding of the walls from ionized plasma, an integrated discharge channel and gas distributor, an instant-start hollow cathode mounted to the plasma source, and an externally mounted keeper, is described. The apparatus offers advantages over other Hall current plasma sources having similar power levels, including: lower mass, longer lifetime, lower part count including fewer power supplies, and the ability to be continuously adjustable to lower average power levels using pulsed operation and adjustment of the pulse duty cycle. The Hall current plasma source can provide propulsion for small spacecraft that either do not have sufficient power to accommodate a propulsion system or do not have available volume to incorporate the larger propulsion systems currently available. The present low-power Hall current plasma source can be used to provide energetic ions to assist the deposition of thin films in plasma processing applications.

Galvanic coupling effects for module-mounting elements of ground-mounted photovoltaic power station

Directory of Open Access Journals (Sweden)

Pierozynski Boguslaw

2017-12-01

Full Text Available This communication reports on the concerns associated with possible generation of galvanic coupling effects for construction materials that are used to manufacture mounting assemblies for ground-mounted photovoltaic (PV power stations. For this purpose, six macro-corrosion galvanic cells were assembled, including: hot-dip Zn/Magnelis®-coated steel/Al and stainless steel (SS/Al cells. Corrosion experiments involved continuous, ca. three-month exposure of these couplings in 3 wt.% NaCl solution, conducted at room temperature for a stable pH value of around 8. All corrosion cells were subjected to regular assessment of galvanic current-density and potential parameters, where special consideration was given to compare the corrosion behaviour of Zn-coated steel samples with that of Magnelis®-coated electrodes. Characterization of surface condition and elemental composition for examined materials was carried-out by means of SEM and EDX spectroscopy techniques.

The alpine flora of Mount Wilhelm (New Guinea)

NARCIS (Netherlands)

Hoogland, R.D.

1958-01-01

The flora of the higher mountains of New Guinea has been the object of several extensive collecting trips in the past forty years. Until quite recently, however, a serious gap in our knowledge was the very scanty information available from the area between Mount Wilhelmina in the West and Mount

Optimization of Classical Hydraulic Engine Mounts Based on RMS Method

Directory of Open Access Journals (Sweden)

J. Christopherson

2005-01-01

Full Text Available Based on RMS averaging of the frequency response functions of the absolute acceleration and relative displacement transmissibility, optimal parameters describing the hydraulic engine mount are determined to explain the internal mount geometry. More specifically, it is shown that a line of minima exists to define a relationship between the absolute acceleration and relative displacement transmissibility of a sprung mass using a hydraulic mount as a means of suspension. This line of minima is used to determine several optimal systems developed on the basis of different clearance requirements, hence different relative displacement requirements, and compare them by means of their respective acceleration and displacement transmissibility functions. In addition, the transient response of the mount to a step input is also investigated to show the effects of the optimization upon the time domain response of the hydraulic mount.

Recent developments: Washington focus

International Nuclear Information System (INIS)

Anon.

1990-01-01

November was a quiet month in Washington. Although Congress has recessed until 1991, the Senate filled vacancies in party leadership positions created by November's elections. The House is expected to proceed with its changes in early December. The Nuclear Energy Forum was held in Washington, DC on November 11-14 to discuss the status of the nuclear industry in the USA. The Forum, held in conjunction with the American Nuclear Society's annual meeting, assembled a large number of CEO's from US, European, and Far Eastern utilities and vendors. The meeting concluded with an announcement by Philip Bayne, President of NYPA and chairman of the Nuclear Power Oversight Committee (NPOC), of the results of a year-long NPOC study entitled a open-quotes Strategic Plan for Building New Nuclear Power Plants.close quotes

Mirror boxes and mirror mounts for photophysics beamline

International Nuclear Information System (INIS)

Raja Rao, P.M.; Raja Sekhar, B.N.; Das, N.C.; Khan, H.A.; Bhattacharya, S.S.; Roy, A.P.

1996-01-01

Photophysics beamline makes use of one metre Seya-Namioka monochromator and two toroidal mirrors in its fore optics. The first toroidal mirror (pre mirror) focuses light originating from the tangent point of the storage ring onto the entrance slit of the monochromator and second toroidal mirror (post mirror) collects light from the exit slit of the monochromator and focuses light onto the sample placed at a distance of about one metre away from the 2nd mirror. To steer light through monochromator and to focus it on the sample of 1mm x 1mm size require precision rotational and translational motion of the mirrors and this has been achieved with the help of precision mirror mounts. Since Indus-1 operates at pressures less than 10 -9 m.bar, the mirror mounts should be manipulated under similar ultra high vacuum conditions. Considering these requirements, two mirror boxes and two mirror mounts have been designed and fabricated. The coarse movements to the mirrors are imparted from outside the mirror chamber with the help of x-y tables and precision movements to the mirrors are achieved with the help of mirror mounts. The UHV compatibility and performance of the mirror mounts connected to mirror boxes under ultra high vacuum condition is evaluated. The details of the design, fabrication and performance evaluation are discussed in this report. 5 refs., 9 figs., 1 tab

“SALOME gave my dignity back”: The role of randomized heroin trials in transforming lives in the Downtown Eastside of Vancouver, Canada

Directory of Open Access Journals (Sweden)

Ehsan Jozaghi

2014-03-01

Full Text Available Although numerous studies on heroin-assisted treatment (HAT have been published in leading international journals, little attention has been given to HAT's clients, their stories, and what constitutes the most influential factor in the treatment process. The present study investigates the role of HAT in transforming the lives of injection drug users (IDUs in Vancouver, Canada. This study is qualitative focusing on 16 in-depth interviews with patients from the randomized trials of HAT. Interviews were transcribed verbatim and analyzed thematically using NVivo 10 software. The findings revealed a positive change in many respects: the randomized trials reduce criminal activity, sex work, and illicit drug use. In addition, the trials improved the health and social functioning of its clients, with some participants acquiring work or volunteer positions. Many of the participants have been able to reconnect with their family members, which was not possible before the program. Furthermore, the relationship between the staff and patients at the project appears to have transformed the behavior of participants. Attending HAT in Vancouver has been particularly effective in creating a unique microenvironment where IDUs who have attended HAT have been able to form a collective identity advocating for their rights. The result of this research points to the need for continuation of the project beyond the current study, leading toward a permanent program.

Ball mounting fixture for a roundness gage

Science.gov (United States)

Gauler, Allen L.; Pasieka, Donald F.

1983-01-01

A ball mounting fixture for a roundness gage is disclosed. The fixture includes a pair of chuck assemblies oriented substantially transversely with respect to one another and mounted on a common base. Each chuck assembly preferably includes a rotary stage and a wobble plate affixed thereto. A ball chuck affixed to each wobble plate is operable to selectively support a ball to be measured for roundness, with the wobble plate permitting the ball chuck to be tilted to center the ball on the axis of rotation of the rotary stage. In a preferred embodiment, each chuck assembly includes a vacuum chuck operable to selectively support the ball to be measured for roundness. The mounting fixture enables a series of roundness measurements to be taken with a conventional rotating gagehead roundness instrument, which measurements can be utilized to determine the sphericity of the ball.

Tension pneumocephalus: Mount Fuji sign

Directory of Open Access Journals (Sweden)

Pulastya Sanyal

2015-01-01

Full Text Available A 13-year-old male was operated for a space occupying lesion in the brain. A noncontrast computed tomography scan done in the late postoperative period showed massive subdural air collection causing compression of bilateral frontal lobes with widening of interhemispheric fissure and the frontal lobes acquiring a peak like configuration - causing tension pneumocephalus-"Mount Fuji sign." Tension pneumocephalus occurs when air enters the extradural or intradural spaces in sufficient volume to exert a mass or pressure effect on the brain, leading to brain herniation. Tension pneumocephalus is a surgical emergency, which needs immediate intervention in the form of decompression of the cranial cavity by a burr hole or needle aspiration. The Mount Fuji sign differentiates tension pneumocephalus from pneumocephalus.

Taking Charge: Walter Sydney Adams and the Mount Wilson Observatory

Science.gov (United States)

Brashear, R.

2004-12-01

The growing preeminence of American observational astronomy in the first half of the 20th century is a well-known story and much credit is given to George Ellery Hale and his skill as an observatory-building entrepreneur. But a key figure who has yet to be discussed in great detail is Walter Sydney Adams (1876-1956), Hale's Assistant Director at Mount Wilson Observatory. Due to Hale's illnesses, Adams was Acting Director for much of Hale's tenure, and he became the second Director of Mount Wilson from 1923 to 1946. Behind his New England reserve Adams was instrumental in the growth of Mount Wilson and thus American astronomy in general. Adams was hand-picked by Hale to take charge of stellar spectroscopy work at Yerkes and Mount Wilson and the younger astronomer showed tremendous loyalty to Hale and Hale's vision throughout his career. As Adams assumed the leadership role at Mount Wilson he concentrated on making the observatory a place where researchers worked with great freedom but maintain a high level of cooperation. This paper will concentrate on Adams's early years and look at his growing relationship with Hale and how he came to be the central figure in the early history of Mount Wilson as both a solar and stellar observatory. His education, his years at Dartmouth and Yerkes (including his unfortunate encounter with epsilon Leonis), and his formative years on Mount Wilson are all important in learning how he shaped the direction of Mount Wilson and the development of American astronomy in the first half of the 20th century. This latter history cannot be complete until we bring Adams into better focus.

Opportunities for addressing laminated root rot caused by Phellinus sulphuracens in Washington's forests: A Report from the Washington State Academy of Sciences in cooperation with the Washington State Department of Natural Resources

Science.gov (United States)

R. James Cook; Robert L. Edmonds; Ned B. Klopfenstein; Willis Littke; Geral McDonald; Daniel Omdahl; Karen Ripley; Charles G. Shaw; Rona Sturrock; Paul Zambino

2013-01-01

This report from the Washington State Academy of Sciences (WSAS) is in response to a request from the Washington State Department of Natural Resources (DNR) to "identify approaches and opportunities ripe for research on understanding and managing root diseases of Douglas-fir." Similar to the process used by the National Research Council, the WSAS upon...

Digital Data for Volcano Hazards in the Mount Jefferson Region, Oregon

Science.gov (United States)

Schilling, S.P.; Doelger, S.; Walder, J.S.; Gardner, C.A.; Conrey, R.M.; Fisher, B.J.

2008-01-01

Mount Jefferson has erupted repeatedly for hundreds of thousands of years, with its last eruptive episode during the last major glaciation which culminated about 15,000 years ago. Geologic evidence shows that Mount Jefferson is capable of large explosive eruptions. The largest such eruption occurred between 35,000 and 100,000 years ago. If Mount Jefferson erupts again, areas close to the eruptive vent will be severely affected, and even areas tens of kilometers (tens of miles) downstream along river valleys or hundreds of kilometers (hundreds of miles) downwind may be at risk. Numerous small volcanoes occupy the area between Mount Jefferson and Mount Hood to the north, and between Mount Jefferson and the Three Sisters region to the south. These small volcanoes tend not to pose the far-reaching hazards associated with Mount Jefferson, but are nonetheless locally important. A concern at Mount Jefferson, but not at the smaller volcanoes, is the possibility that small-to-moderate sized landslides could occur even during periods of no volcanic activity. Such landslides may transform as they move into lahars (watery flows of rock, mud, and debris) that can inundate areas far downstream. The geographic information system (GIS) volcano hazard data layer used to produce the Mount Jefferson volcano hazard map in USGS Open-File Report 99-24 (Walder and others, 1999) is included in this data set. Both proximal and distal hazard zones were delineated by scientists at the Cascades Volcano Observatory and depict various volcano hazard areas around the mountain.

A magneto-rheological fluid mount featuring squeeze mode: analysis and testing

International Nuclear Information System (INIS)

Chen, Peng; Bai, Xian-Xu; Qian, Li-Jun; Choi, Seung-Bok

2016-01-01

This paper presents a mathematical model for a new semi-active vehicle engine mount utilizing magneto-rheological (MR) fluids in squeeze mode (MR mount in short) and validates the model by comparing analysis results with experimental tests. The proposed MR mount is mainly comprised of a frame for installation, a main rubber, a squeeze plate and a bobbin for coil winding. When the magnetic fields on, MR effect occurs in the upper gap between the squeeze plate and the bobbin, and the dynamic stiffness can be controlled by tuning the applied currents. Employing Bingham model and flow properties between parallel plates of MR fluids, a mathematical model for the squeeze type of MR mount is formulated with consideration of the fluid inertia, MR effect and hysteresis property. The field-dependent dynamic stiffness of the MR mount is then analyzed using the established mathematical model. Subsequently, in order to validate the mathematical model, an appropriate size of MR mount is fabricated and tested. The field-dependent force and dynamic stiffness of the proposed MR mount are evaluated and compared between the model and experimental tests in both time and frequency domains to verify the model efficiency. In addition, it is shown that both the damping property and the stiffness property of the proposed MR mount can be simultaneously controlled. (paper)

Solar rotation measurements at Mount Wilson. Pt. 2

International Nuclear Information System (INIS)

Labonte, B.J.; Howard, R.; Carnegie Institution of Washington, Pasadena

1981-01-01

Possible sources of systematic error in solar Doppler rotational velocities are examined. Scattered light is shown to affect the Mount Wilson solar rotation results, but this effect is not enough to bring the spectroscopic results in coincidence with the sunspot rotation. Interference fringes at the spectrograph focus at Mount Wilson have in two intervals affected the rotation results. It has been possible to correlate this error with temperature and thus correct for it. A misalignment between the entrance and exit slits is a possible source of error, but for the Mount Wilson slit configuration the amplitude of this effect is negligibly small. Rapid scanning of the solar image also produces no measurable effect. (orig.)

Rapid mounting of adult Drosophila structures in Hoyer's medium.

Science.gov (United States)

Stern, David L; Sucena, Elio

2012-01-01

The Drosophila cuticle carries a rich array of morphological details. Thus, cuticle examination has had a central role in the history of genetics. This protocol describes a procedure for mounting adult cuticles in Hoyer's medium, a useful mountant for both larval and adult cuticles. The medium digests soft tissues rapidly, leaving the cuticle cleared for observation. In addition, samples can be transferred directly from water to Hoyer's medium. However, specimens mounted in Hoyer's medium degrade over time. For example, the fine denticles on the larval dorsum are best observed soon after mounting; they begin to fade after 1 week, and can disappear completely after several months. More robust features, such as the ventral denticle belts, will persist for a longer period of time. Because adults cannot profitably be mounted whole in Hoyer's medium, some dissection is necessary.

Structure and agency: reflections from an exploratory study of Vancouver indoor sex workers.

Science.gov (United States)

Bungay, Vicky; Halpin, Michael; Atchison, Chris; Johnston, Caitlin

2011-01-01

Sex work research continues to be characterised by debates around decriminalization. Central to these debates are claims about the agency of those involved in the sex trade. Some researchers argue that individuals involved in the sex trade are victims of structural and interpersonal constraint, whilst others depict them as workers exercising choice. Drawing on structure-agency theory, a review of legal and media accounts of the sex trade and qualitative interviews with 21 indoor sex workers in Vancouver, Canada, we argue that both of these perspectives are insufficient. Rather than reducing the sex trade to part of a binary, we suggest that it is necessary to analyse sex work through the complex interplay of both structure and agency. Specifically, structural analyses undercover the numerous ways that sex workers are controlled, observed and influenced whilst agency perspectives elicit the means that sex workers continue to exercise control in spite of disadvantage. While we do not finalise decriminalisation debates, we do critique current Canadian laws for the lack of responsiveness to the lives of sex workers and their exploitative and contradictory stance on sex work.

Mounting system for optical frequency reference cavities

Science.gov (United States)

Notcutt, Mark (Inventor); Hall, John L. (Inventor); Ma, Long-Sheng (Inventor)

2008-01-01

A technique for reducing the vibration sensitivity of laser-stabilizing optical reference cavities is based upon an improved design and mounting method for the cavity, wherein the cavity is mounted vertically. It is suspended at one plane, around the spacer cylinder, equidistant from the mirror ends of the cavity. The suspension element is a collar of an extremely low thermal expansion coefficient material, which surrounds the spacer cylinder and contacts it uniformly. Once the collar has been properly located, it is cemented in place so that the spacer cylinder is uniformly supported and does not have to be squeezed at all. The collar also includes a number of cavities partially bored into its lower flat surface, around the axial bore. These cavities are support points, into which mounting base pins will be inserted. Hence the collar is supported at a minimum of three points.

Exploring Virtual Worlds With Head-Mounted Displays

Science.gov (United States)

Chung, James C.; Harris, Mark R.; Brooks, Frederick P.; Fuchs, Henry; Kelley, Michael T.; Hughes, John W.; Ouh-Young, Ming; Cheung, Clement; Holloway, Richard L.; Pique, Michael

1989-09-01

For nearly a decade the University of North Carolina at Chapel Hill has been conducting research in the use of simple head-mounted displays in "real-world" applications. Such units provide the user with non-holographic true three-dimensional information, since the kinetic depth effect, stereoscopy, and other visual cues combine to immerse the user in a "virtual world" which behaves like the real world in some respects. UNC's head-mounted display was built inexpensively from commercially available off-the-shelf components. Tracking of the the user's head position and orientation is performed by a Polhemus Navigation Sciences' 3SPACE* tracker. The host computer uses the tracking information to generate updated images corresponding to the user's new left eye and right eye views. The images are broadcast to two liquid crystal television screens (220x320 pixels) mounted on a horizontal shelf at the user's forehead. The user views these color screens through half-silvered mirrors, enabling the computer-generated image to be superimposed upon the user's real physical environment. The head-mounted display has been incorporated into existing molecular modeling and architectural applications being developed at UNC. In molecular structure studies, chemists are presented with a room-sized molecule with which they can interact in a manner more intuitive than that provided by conventional two-dimensional displays and dial boxes. Walking around and through the large molecule may provide quicker understanding of its structure, and such problems as drug-enzyme docking may be approached with greater insight. In architecture, the head-mounted display enables clients to better appreciate three-dimensional designs, which may be misinterpreted in their conventional two-dimensional form by untrained eyes. The addition of a treadmill to the system provides additional kinesthetic input into the understanding of building size and scale.

Mount Oku, Cameroon Volcanic Line

African Journals Online (AJOL)

and continental sectors especially for trace elements in basalts. ... continental sector of the trend is a complex .... values higher than those of HIMU but is within ...... (Mount Cameroon, Central Africa): petrogenetic implications. Miner. Petrol.,.

Micro-inverter solar panel mounting

Science.gov (United States)

Morris, John; Gilchrist, Phillip Charles

2016-02-02

Processes, systems, devices, and articles of manufacture are provided. Each may include adapting micro-inverters initially configured for frame-mounting to mounting on a frameless solar panel. This securement may include using an adaptive clamp or several adaptive clamps secured to a micro-inverter or its components, and using compressive forces applied directly to the solar panel to secure the adaptive clamp and the components to the solar panel. The clamps can also include compressive spacers and safeties for managing the compressive forces exerted on the solar panels. Friction zones may also be used for managing slipping between the clamp and the solar panel during or after installation. Adjustments to the clamps may be carried out through various means and by changing the physical size of the clamps themselves.

Geology of the Ugashik-Mount Peulik Volcanic Center, Alaska

Science.gov (United States)

Miller, Thomas P.

2004-01-01

The Ugashik-Mount Peulik volcanic center, 550 km southwest of Anchorage on the Alaska Peninsula, consists of the late Quaternary 5-km-wide Ugashik caldera and the stratovolcano Mount Peulik built on the north flank of Ugashik. The center has been the site of explosive volcanism including a caldera-forming eruption and post-caldera dome-destructive activity. Mount Peulik has been formed entirely in Holocene time and erupted in 1814 and 1845. A large lava dome occupies the summit crater, which is breached to the west. A smaller dome is perched high on the southeast flank of the cone. Pyroclastic-flow deposits form aprons below both domes. One or more sector-collapse events occurred early in the formation of Mount Peulik volcano resulting in a large area of debris-avalanche deposits on the volcano's northwest flank. The Ugashik-Mount Peulik center is a calcalkaline suite of basalt, andesite, dacite, and rhyolite, ranging in SiO2 content from 51 to 72 percent. The Ugashik-Mount Peulik magmas appear to be co-genetic in a broad sense and their compositional variation has probably resulted from a combination of fractional crystallization and magma-mixing. The most likely scenario for a future eruption is that one or more of the summit domes on Mount Peulik are destroyed as new magma rises to the surface. Debris avalanches and pyroclastic flows may then move down the west and, less likely, east flanks of the volcano for distances of 10 km or more. A new lava dome or series of domes would be expected to form either during or within some few years after the explosive disruption of the previous dome. This cycle of dome disruption, pyroclastic flow generation, and new dome formation could be repeated several times in a single eruption. The volcano poses little direct threat to human population as the area is sparsely populated. The most serious hazard is the effect of airborne volcanic ash on aircraft since Mount Peulik sits astride heavily traveled air routes connecting the U

Drivers' use of marijuana in Washington state : traffic tech.

Science.gov (United States)

2016-08-01

In July 2014, Washington State allowed legal sales of : recreational marijuana. Working with the Washington : Traffic Safety Commission, NHTSA assisted the State in : conducting a roadside study to examine the prevalence : of marijuana use before and...

Alternative mounting media for preservation of some protozoa.

Science.gov (United States)

Criado-Fornelio, A; Heredero-Bermejo, I; Pérez-Serrano, J

2014-10-01

Protozoa resistant stages are disintegrated when mounted in toluene-based media. To overcome such problem, three toluene-free mountants were tested on preserve Acanthamoeba spp and gregarines. Two commercial glues based on cyanoacrylate or trimethoxysilane were suitable for preserving both cysts and trophozoites. Hoyer's medium showed good results for mounting gregarine oocysts. Copyright © 2014 Elsevier B.V. All rights reserved.

Hole-thru-laminate mounting supports for photovoltaic modules

Science.gov (United States)

Wexler, Jason; Botkin, Jonathan; Culligan, Matthew; Detrick, Adam

2015-02-17

A mounting support for a photovoltaic module is described. The mounting support includes a pedestal having a surface adaptable to receive a flat side of a photovoltaic module laminate. A hole is disposed in the pedestal, the hole adaptable to receive a bolt or a pin used to couple the pedestal to the flat side of the photovoltaic module laminate.

Three-dimensional repositioning accuracy of semiadjustable articulator cast mounting systems.

Science.gov (United States)

Tan, Ming Yi; Ung, Justina Youlin; Low, Ada Hui Yin; Tan, En En; Tan, Keson Beng Choon

2014-10-01

In spite of its importance in prosthesis precision and quality, the 3-dimensional repositioning accuracy of cast mounting systems has not been reported in detail. The purpose of this study was to quantify the 3-dimensional repositioning accuracy of 6 selected cast mounting systems. Five magnetic mounting systems were compared with a conventional screw-on system. Six systems on 3 semiadjustable articulators were evaluated: Denar Mark II with conventional screw-on mounting plates (DENSCR) and magnetic mounting system with converter plates (DENCON); Denar Mark 330 with in-built magnetic mounting system (DENMAG) and disposable mounting plates; and Artex CP with blue (ARTBLU), white (ARTWHI), and black (ARTBLA) magnetic mounting plates. Test casts with 3 high-precision ceramic ball bearings at the mandibular central incisor (Point I) and the right and left second molar (Point R; Point L) positions were mounted on 5 mounting plates (n=5) for all 6 systems. Each cast was repositioned 10 times by 4 operators in random order. Nine linear (Ix, Iy, Iz; Rx, Ry, Rz; Lx, Ly, Lz) and 3 angular (anteroposterior, mediolateral, twisting) displacements were measured with a coordinate measuring machine. The mean standard deviations of the linear and angular displacements defined repositioning accuracy. Anteroposterior linear repositioning accuracy ranged from 23.8 ±3.7 μm (DENCON) to 4.9 ±3.2 μm (DENSCR). Mediolateral linear repositioning accuracy ranged from 46.0 ±8.0 μm (DENCON) to 3.7 ±1.5 μm (ARTBLU), and vertical linear repositioning accuracy ranged from 7.2 ±9.6 μm (DENMAG) to 1.5 ±0.9 μm (ARTBLU). Anteroposterior angular repositioning accuracy ranged from 0.0084 ±0.0080 degrees (DENCON) to 0.0020 ±0.0006 degrees (ARTBLU), and mediolateral angular repositioning accuracy ranged from 0.0120 ±0.0111 degrees (ARTWHI) to 0.0027 ±0.0008 degrees (ARTBLU). Twisting angular repositioning accuracy ranged from 0.0419 ±0.0176 degrees (DENCON) to 0.0042 ±0.0038 degrees

Sensor mount assemblies and sensor assemblies

Science.gov (United States)

Miller, David H [Redondo Beach, CA

2012-04-10

Sensor mount assemblies and sensor assemblies are provided. In an embodiment, by way of example only, a sensor mount assembly includes a busbar, a main body, a backing surface, and a first finger. The busbar has a first end and a second end. The main body is overmolded onto the busbar. The backing surface extends radially outwardly relative to the main body. The first finger extends axially from the backing surface, and the first finger has a first end, a second end, and a tooth. The first end of the first finger is disposed on the backing surface, and the tooth is formed on the second end of the first finger.

Perspective with Landsat Overlay, Mount Kilimanjaro, Tanzania

Science.gov (United States)

2002-01-01

Mount Kilimanjaro (Kilima Njaro or 'shining mountain' in Swahili), the highest point in Africa, reaches 5,895 meters (19,340 feet) above sea level, tall enough to maintain a permanent snow cap despite being just 330 kilometers (210 miles) south of the equator. It is the tallest free-standing mountain on the Earth's land surface world, rising about 4,600 meters (15,000 feet) above the surrounding plain. Kilimanjaro is a triple volcano (has three peaks) that last erupted perhaps more than 100,000 years ago but still exudes volcanic gases. It is accompanied by about 20 other nearby volcanoes, some of which are seen to the west (left) in this view, prominently including Mount Meru, which last erupted only about a century ago. The volcanic mountain slopes are commonly fertile and support thick forests, while the much drier grasslands of the plains are home to elephants, lions, and other savanna wildlife.This 3-D perspective view was generated using topographic data from the Shuttle Radar Topography Mission (SRTM), a Landsat 7 satellite image, and a false sky. Topographic expression is vertically exaggerated two times.Landsat has been providing visible and infrared views of the Earth since 1972. SRTM elevation data matches the 30-meter (98-foot) resolution of most Landsat images and will substantially help in analyzing the large and growing Landsat image archive, managed by the U.S. Geological Survey (USGS).Elevation data used in this image was acquired by the Shuttle Radar Topography Mission (SRTM) aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and

The January 2006 Volcanic-Tectonic Earthquake Swarm at Mount Martin, Alaska

Science.gov (United States)

Dixon, James P.; Power, John A.

2009-01-01

On January 8, 2006, a swarm of volcanic-tectonic earthquakes began beneath Mount Martin at the southern end of the Katmai volcanic cluster. This was the first recorded swarm at Mount Martin since continuous seismic monitoring began in 1996. The number of located earthquakes increased during the next four days, reaching a peak on January 11. For the next two days, the seismic activity decreased, and on January 14, the number of events increased to twice the previous day's total. Following this increase in activity, seismicity declined, returning to background levels by the end of the month. The Alaska Volcano Observatory located 860 earthquakes near Mount Martin during January 2006. No additional signs of volcanic unrest were noted in association with this earthquake swarm. The earthquakes in the Mount Martin swarm, relocated using the double difference technique, formed an elongated cluster dipping to the southwest. Focal mechanisms beneath Mount Martin show a mix of normal, thrust, and strike-slip solutions, with normal focal mechanisms dominating. For earthquakes more than 1 km from Mount Martin, all focal mechanisms showed normal faulting. The calculated b-value for the Mount Martin swarm is 0.98 and showed no significant change before, during, or after the swarm. The triggering mechanism for the Mount Martin swarm is unknown. The time-history of earthquake occurrence is indicative of a volcanic cause; however, there were no low-frequency events or observations, such as increased steaming associated with the swarm. During the swarm, there was no change in the b-value, and the distribution and type of focal mechanisms were similar to those in the period before the anomalous activity. The short duration of the swarm, the similarity in observed focal mechanisms, and the lack of additional signs of unrest suggest this swarm did not result from a large influx of magma within the shallow crust beneath Mount Martin.

Low-stress mounting configuration design for large aperture laser transport mirror

Science.gov (United States)

Zhang, Zheng; Quan, Xusong; Yao, Chao; Wang, Hui

2016-10-01

TM1-6S1 large aperture laser transport mirror is a crucial optical unit of high power solid-state laser in the Inertial Confinement Fusion (ICF) facility. This article focuses on the low-stress and precise mounting method of large-aperture mirror. Based on the engineering practice of SG-III, the state-of-the-art and key problems of current mounting configuration are clarified firstly. Subsequently, a brand new low-stress mounting configuration with flexure supports is proposed. Opto-mechanical model of the mirror under mounting force is built up with elastic mechanics theory. Further, numerical methods and field tests are employed to verify the favorable load uniform capacity and load adjust capacity of flexure supports. With FEM, the relation between the mounting force from new configuration and the mirror surface distortion (wavefront error) is clarified. The novel mounting method of large aperture optics could be not only used on this laser transport mirror, but also on the other transmission optics and large crystals in ICF facilities.

Head-Mounted Display Technology for Low Vision Rehabilitation and Vision Enhancement

Science.gov (United States)

Ehrlich, Joshua R.; Ojeda, Lauro V.; Wicker, Donna; Day, Sherry; Howson, Ashley; Lakshminarayanan, Vasudevan; Moroi, Sayoko E.

2017-01-01

Purpose To describe the various types of head-mounted display technology, their optical and human factors considerations, and their potential for use in low vision rehabilitation and vision enhancement. Design Expert perspective. Methods An overview of head-mounted display technology by an interdisciplinary team of experts drawing on key literature in the field. Results Head-mounted display technologies can be classified based on their display type and optical design. See-through displays such as retinal projection devices have the greatest potential for use as low vision aids. Devices vary by their relationship to the user’s eyes, field of view, illumination, resolution, color, stereopsis, effect on head motion and user interface. These optical and human factors considerations are important when selecting head-mounted displays for specific applications and patient groups. Conclusions Head-mounted display technologies may offer advantages over conventional low vision aids. Future research should compare head-mounted displays to commonly prescribed low vision aids in order to compare their effectiveness in addressing the impairments and rehabilitation goals of diverse patient populations. PMID:28048975

Robotic mounting of ATLAS barrel SCT modules

International Nuclear Information System (INIS)

Nickerson, R.B.; Viehhauser, G.; Wastie, R.; Terada, S.; Unno, Y.; Kohriki, T.; Ikegami, Y.; Hara, K.; Kobayashi, H.; Barbier, G.; Clark, A.G.; Perrin, E.; Carter, A.A.; Mistry, J.; Morris, J.

2006-01-01

The 2112 silicon detector modules of the barrel part of the ATLAS SemiConductor Tracker (SCT) have been mounted on their carbon fibre support structure. Module insertion, placement and fixing were performed by robotic assembly tooling. We report on our experience with this assembly method. Part of the mounting sequence involves a partial survey of elements of the support structure which is needed to align the modules properly during insertion. An analysis of these data is used to estimate the positional accuracy of the robots

National Ingition Facility subsystem design requirements optical mounts SSDR 1.4.4

International Nuclear Information System (INIS)

Richardson, M.

1996-01-01

This SSDR establishes the performance, design, development and test requirements for NIF Beam Transport Optomechanical Subsystems. optomechanical Subsystems includes the mounts for the beam transport mirrors, LMl - LM8, the polarizer mount, and the spatial filter lens mounts

Universal Coverage without Universal Access: Institutional Barriers to Health Care among Women Sex Workers in Vancouver, Canada.

Directory of Open Access Journals (Sweden)

M Eugenia Socías

Full Text Available Access to health care is a crucial determinant of health. Yet, even within settings that purport to provide universal health coverage (UHC, sex workers' experiences reveal systematic, institutionally ingrained barriers to appropriate quality health care. The aim of this study was to assess prevalence and correlates of institutional barriers to care among sex workers in a setting with UHC.Data was drawn from an ongoing community-based, prospective cohort of women sex workers in Vancouver, Canada (An Evaluation of Sex Workers' Health Access. Multivariable logistic regression analyses, using generalized estimating equations (GEE, were employed to longitudinally investigate correlates of institutional barriers to care over a 44-month follow-up period (January 2010-August 2013.In total, 723 sex workers were included, contributing to 2506 observations. Over the study period, 509 (70.4% women reported one or more institutional barriers to care. The most commonly reported institutional barriers to care were long wait times (54.6%, limited hours of operation (36.5%, and perceived disrespect by health care providers (26.1%. In multivariable GEE analyses, recent partner- (adjusted odds ratio [AOR] = 1.46, % 95% Confidence Interval [CI] 1.10-1.94, workplace- (AOR = 1.31, 95% CI 1.05-1.63, and community-level violence (AOR = 1.41, 95% CI 1.04-1.92, as well as other markers of vulnerability, such as self-identification as a gender/sexual minority (AOR = 1.32, 95% CI 1.03-1.69, a mental illness diagnosis (AOR = 1.66, 95% CI 1.34-2.06, and lack of provincial health insurance card (AOR = 3.47, 95% CI 1.59-7.57 emerged as independent correlates of institutional barriers to health services.Despite Canada's UHC, women sex workers in Vancouver face high prevalence of institutional barriers to care, with highest burden among most marginalized women. These findings underscore the need to explore new models of care, alongside broader policy changes to fulfill sex

Universal Coverage without Universal Access: Institutional Barriers to Health Care among Women Sex Workers in Vancouver, Canada.

Science.gov (United States)

Socías, M Eugenia; Shoveller, Jean; Bean, Chili; Nguyen, Paul; Montaner, Julio; Shannon, Kate

2016-01-01

Access to health care is a crucial determinant of health. Yet, even within settings that purport to provide universal health coverage (UHC), sex workers' experiences reveal systematic, institutionally ingrained barriers to appropriate quality health care. The aim of this study was to assess prevalence and correlates of institutional barriers to care among sex workers in a setting with UHC. Data was drawn from an ongoing community-based, prospective cohort of women sex workers in Vancouver, Canada (An Evaluation of Sex Workers' Health Access). Multivariable logistic regression analyses, using generalized estimating equations (GEE), were employed to longitudinally investigate correlates of institutional barriers to care over a 44-month follow-up period (January 2010-August 2013). In total, 723 sex workers were included, contributing to 2506 observations. Over the study period, 509 (70.4%) women reported one or more institutional barriers to care. The most commonly reported institutional barriers to care were long wait times (54.6%), limited hours of operation (36.5%), and perceived disrespect by health care providers (26.1%). In multivariable GEE analyses, recent partner- (adjusted odds ratio [AOR] = 1.46, % 95% Confidence Interval [CI] 1.10-1.94), workplace- (AOR = 1.31, 95% CI 1.05-1.63), and community-level violence (AOR = 1.41, 95% CI 1.04-1.92), as well as other markers of vulnerability, such as self-identification as a gender/sexual minority (AOR = 1.32, 95% CI 1.03-1.69), a mental illness diagnosis (AOR = 1.66, 95% CI 1.34-2.06), and lack of provincial health insurance card (AOR = 3.47, 95% CI 1.59-7.57) emerged as independent correlates of institutional barriers to health services. Despite Canada's UHC, women sex workers in Vancouver face high prevalence of institutional barriers to care, with highest burden among most marginalized women. These findings underscore the need to explore new models of care, alongside broader policy changes to fulfill sex workers

Some technical solutions on organization and technology of reactor room component mounting

International Nuclear Information System (INIS)

Romanovskij, V.I.

1982-01-01

Design of the production equipment for mounting sites of heat facilities of the Zaporozhe NPP is considered. Plan of the production equipment for mounting sites of heat facilities and flowsheet of mounting of supporting truss of the reactor are presented

Polymethylmethacrylate-based luminescent solar concentrators with bottom-mounted solar cells

International Nuclear Information System (INIS)

Zhang, Yi; Sun, Song; Kang, Rui; Zhang, Jun; Zhang, Ningning; Yan, Wenhao; Xie, Wei; Ding, Jianjun; Bao, Jun; Gao, Chen

2015-01-01

Graphical abstract: - Highlights: • Bottom-mounted luminescent solar concentrators on dye-doped plates were studied. • The mechanism of transport process was proposed. • The fabricated luminescent solar concentrator achieved a gain of 1.38. • Power conversion efficiency of 5.03% was obtained with cell area coverage of 27%. • The lowest cost per watt of $1.89 was optimized with cell area coverage of 18%. - Abstract: Luminescent solar concentrators offer an attractive approach to concentrate sunlight economically without tracking, but the narrow absorption band of luminescent materials hinders their further development. This paper describes bottom-mounted luminescent solar concentrators on dye-doped polymethylmethacrylate plates that absorb not only the waveguided light but also the transmitted sunlight and partial fluorescent light in the escape cone. A series of bottom-mounted luminescent solar concentrators with size of 78 mm × 78 mm × 7 mm were fabricated and their gain and power conversion efficiency were investigated. The transport process of the waveguided light and the relationship between the bottom-mounted cells were studied to optimize the performance of the device. The bottom-mounted luminescent solar concentrator with cell area coverage of 9% displayed a cell gain of 1.38, to our best knowledge, which is the highest value for dye-doped polymethylmethacrylate plate luminescent solar concentrators. Power conversion efficiency as high as 5.03% was obtained with cell area coverage of 27%. Furthermore, the bottom-mounted luminescent solar concentrator was found to have a lowest cost per watt of $1.89 with cell area coverage of 18%. These results suggested that the fabricated bottom-mounted luminescent solar concentrator may have a potential in low-cost building integrated photovoltaic application

A new mount with moving-magnet type electromagnetic actuator for naval shipboard equipment

Directory of Open Access Journals (Sweden)

Yun-Ho Shin

2015-01-01

Full Text Available This study is proposed a new hybrid mount having a moving-magnet type electromagnetic actuator to reduce the vibration transmitted from naval shipboard equipment to the structure of the ship 's hull. Optimal design specifications are determined through experimental analysis. The detailed design of the hybrid mount is determined through several design steps with electromagnetic numerical analysis using Maxwell Software(S/W. The hybrid mount that combines a rubber mount and an electromagnetic actuator has a fail-safe function for shock resistance. The mount is fabricated and tested using a universal testing machine to evaluate the design specifications. Finally, numerical simulation of the hybrid mount is performed to confirm control performance and applicability.

49 CFR 587.19 - Mounting.

Science.gov (United States)

2010-10-01

... Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) DEFORMABLE BARRIERS Offset Deformable Barrier § 587.19 Mounting. (a) The deformable face is rigidly attached to the edge of the fixed rigid barrier or to some rigid...

Preparation of samples for leaf architecture studies, a method for mounting cleared leaves.

Science.gov (United States)

Vasco, Alejandra; Thadeo, Marcela; Conover, Margaret; Daly, Douglas C

2014-09-01

Several recent waves of interest in leaf architecture have shown an expanding range of approaches and applications across a number of disciplines. Despite this increased interest, examination of existing archives of cleared and mounted leaves shows that current methods for mounting, in particular, yield unsatisfactory results and deterioration of samples over relatively short periods. Although techniques for clearing and staining leaves are numerous, published techniques for mounting leaves are scarce. • Here we present a complete protocol and recommendations for clearing, staining, and imaging leaves, and, most importantly, a method to permanently mount cleared leaves. • The mounting protocol is faster than other methods, inexpensive, and straightforward; moreover, it yields clear and permanent samples that can easily be imaged, scanned, and stored. Specimens mounted with this method preserve well, with leaves that were mounted more than 35 years ago showing no signs of bubbling or discoloration.

The January 1989 Nestucca oil spill on the West Coast of Vancouver Island, British Columbia

International Nuclear Information System (INIS)

Davis, J.C.

1990-01-01

This paper reports that at the beginning of January 1989, bunker C oil from the barge Nestucca began coming ashore on the West Coast of Vancouver Island, necessitating a major environmental assessment and clean-up response on the part of a number of Canadian agencies, volunteers, Native groups and concerned Parties. The oil impacted the exposed outer coastline, including the recreational beaches of Pacific Rim National Park, and caused concerns with respect to harvesting the shellfish and other marine life, the important salmon and herring resources of the area, marine mammals including two colonies of sea otters and also with respect to seabird mortality. This spill, coupled wit public sensitivity to the Exxon Valdez spill and the transportation of oil and hazardous substances along the West Coast, led to several public inquiry processes as well as internal reviews of agency response, preparedness and other issues and generated considerable public outcry and criticism

Active Figure Control Effects on Mounting Strategy for X-Ray Optics

Science.gov (United States)

Kolodziejczak, Jeffery J.; Atkins, Carolyn; Roche, Jacqueline M.; ODell, Stephen L.; Ramsey, Brian D.; Elsner, Ronald F.; Weisskopf, Martin C.; Gubarev, Mikhail V.

2014-01-01

As part of ongoing development efforts at MSFC, we have begun to investigate mounting strategies for highly nested xray optics in both full-shell and segmented configurations. The analytical infrastructure for this effort also lends itself to investigation of active strategies. We expect that a consequence of active figure control on relatively thin substrates is that errors are propagated to the edges, where they might affect the effective precision of the mounting points. Based upon modeling, we describe parametrically, the conditions under which active mounts are preferred over fixed ones, and the effect of active figure corrections on the required number, locations, and kinematic characteristics of mounting points.

Washington biofuel feedstock crop supply under output price and quantity uncertainty

International Nuclear Information System (INIS)

Zheng Qiujie; Shumway, C. Richard

2012-01-01

Subsidized development of an in-state biofuels industry has received some political support in the state of Washington, USA. Utilizing in-state feedstock supplies could be an efficient way to stimulate biofuel industries and the local economy. In this paper we estimate supply under output price and quantity uncertainty for major biofuel feedstock crops in Washington. Farmers are expected to be risk averse and maximize the utility of profit and uncertainty. We estimate very large Washington price elasticities for corn and sugar beets but a small price elasticity for a third potential feedstock, canola. Even with the large price elasticities for two potential feedstocks, their current and historical production levels in the state are so low that unrealistically large incentives would likely be needed to obtain sufficient feedstock supply for a Washington biofuel industry. Based on our examination of state and regional data, we find low likelihood that a Washington biofuels industry will develop in the near future primarily using within-state biofuel feedstock crops. - Highlights: ► Within-state feedstock crop supplies insufficient for Washington biofuel industry. ► Potential Washington corn and sugar beet supplies very responsive to price changes. ► Feedstock supplies more responsive to higher expected profit than lower risk. ► R and D for conversion of waste cellulosic feedstocks is potentially important policy.

An assessment of interstate safety investment properties in Washington state.

Science.gov (United States)

2014-12-01

The Washington State Department of Transportation (WSDOT) commissioned the current study, targeting the entire interstate : mainline network in Washington State, to provide strategic direction to multi-biennial investment interstate locations that of...

Expanding Access and Opportunity: The Washington State Achievers Program

Science.gov (United States)

Ramsey, Jennifer; Gorgol, Laura

2010-01-01

In 2001, the Bill & Melinda Gates Foundation launched a 10-year, multi-million dollar initiative, the Washington State Achievers Program (WSA), to increase opportunities for low-income students to attend postsecondary institutions in Washington State. The Bill & Melinda Gates Foundation granted funds to the College Success Foundation…

Expanding Access and Opportunity: The Washington State Achievers Scholarship

Science.gov (United States)

O'Brien, Colleen

2011-01-01

In 2001, the Bill & Melinda Gates Foundation launched the multi-year, multi-million dollar Washington State Achievers Scholarship program. Concerned about disparities in college participation for low-income students in the state of Washington versus their wealthier peers, the Gates Foundation partnered with the College Success Foundation…

Effects of catastrophic floods and debris flows on the sediment retention structure, North Fork Toutle River, Washington

Science.gov (United States)

Denlinger, Roger P.

2012-01-01

The eruption of Mount St. Helens in 1980 produced a debris avalanche that flowed down the upper reaches of the North Fork Toutle River in southwestern Washington, clogging this drainage with sediment. In response to continuous anomalously high sediment flux into the Toutle and Cowlitz Rivers resulting from this avalanche and associated debris flows, the U.S. Army Corps of Engineers completed a Sediment Retention Structure (SRS) on the North Fork Toutle River in May 1989. For one decade, the SRS effectively blocked most of the sediment transport down the Toutle River. In 1999, the sediment level behind the SRS reached the elevation of the spillway base. Since then, a higher percentage of sediment has been passing the SRS and increasing the flood risk in the Cowlitz River. Currently (2012), the dam is filling with sediment at a rate that cannot be sustained for its original design life, and the U.S. Army Corps of Engineers is concerned with the current ability of the SRS to manage floods. This report presents an assessment of the ability of the dam to pass large flows from three types of scenarios (it is assumed that no damage to the spillway will occur). These scenarios are (1) a failure of the debris-avalanche blockage forming Castle Lake that produces a dambreak flood, (2) a debris flow from failure of that blockage, or (3) a debris flow originating in the crater of Mount St. Helens. In each case, the flows are routed down the Toutle River and through the SRS using numerical models on a gridded domain produced from a digital elevation model constructed with existing topography and dam infrastructure. The results of these simulations show that a structurally sound spillway is capable of passing large floods without risk of overtopping the crest of the dam. In addition, large debris flows originating from Castle Lake or the crater of Mount St. Helens never reach the SRS. Instead, debris flows fill the braided channels upstream of the dam and reduce its storage

[Does the mounting of gastrointestinal biopsies on millipore filter contribute to an improved section quality?

DEFF Research Database (Denmark)

Asmussen, L.; Bernstein, I.; Matzen, P.

2009-01-01

orientation, GIB is occasionally mounted on millipore filter (MF) in an attempt to place the deep cut side onto the MF. The importance of this technique for section quality is evaluated in this study. MATERIAL AND METHOD: The material comprised three consecutive series of GIB (60 gastric, duodenal......, and colorectal GIB, respectively). Sections were grouped in MF-mounted versus non-mounted GIB, the proportion of fully acceptable sections among mounted versus non-mounted GIB was recorded. RESULTS: 77.2% of all GIBs were MF-mounted. 33.1% of mounted GIBs versus 48.8% of non-mounted GIBs were assessed as fully...... acceptable sections. The differences between these figures are not statistically significant. 41.7% of the mounted GIBs were placed with the mucosal surface facing the MF, which entails a risk of damaging the tissue. CONCLUSION: MF-mounting of GIB did not contribute to section quality. Since the handling...

Mount Protects Thin-Walled Glass or Ceramic Tubes from Large Thermal and Vibration Loads

Science.gov (United States)

Amato, Michael; Schmidt, Stephen; Marsh. James; Dahya, Kevin

2011-01-01

The design allows for the low-stress mounting of fragile objects, like thin walled glass, by using particular ways of compensating, isolating, or releasing the coefficient of thermal expansion (CTE) differences between the mounted object and the mount itself. This mount profile is lower than true full kinematic mounting. Also, this approach enables accurate positioning of the component for electrical and optical interfaces. It avoids the higher and unpredictable stress issues that often result from potting the object. The mount has been built and tested to space-flight specifications, and has been used for fiber-optic, optical, and electrical interfaces for a spaceflight mission. This mount design is often metal and is slightly larger than the object to be mounted. The objects are optical or optical/electrical, and optical and/or electrical interfaces are required from the top and bottom. This requires the mount to be open at both ends, and for the object s position to be controlled. Thin inside inserts at the top and bottom contact the housing at defined lips, or edges, and hold the fragile object in the mount. The inserts can be customized to mimic the outer surface of the object, which further reduces stress. The inserts have the opposite CTE of the housing material, partially compensating for the CTE difference that causes thermal stress. A spring washer is inserted at one end to compensate for more CTE difference and to hold the object against the location edge of the mount for any optical position requirements. The spring also ensures that any fiber-optic or optic interface, which often requires some pressure to ensure a good interface, does not overstress the fragile object. The insert thickness, material, and spring washer size can be traded against each other to optimize the mount and stresses for various thermal and vibration load ranges and other mounting requirements. The alternate design uses two separate, unique features to reduce stress and hold the

Control of Wall Mounting Robot

DEFF Research Database (Denmark)

Sloth, Christoffer; Pedersen, Rasmus

2017-01-01

This paper presents a method for designing controllers for trajectory tracking with actuator constraints. In particular, we consider a joystick-controlled wall mounting robot called WallMo. In contrast to previous works, a model-free approach is taken to the control problem, where the path...

Preparation of Samples for Leaf Architecture Studies, A Method for Mounting Cleared Leaves

Directory of Open Access Journals (Sweden)

Alejandra Vasco

2014-09-01

Full Text Available Premise of the study: Several recent waves of interest in leaf architecture have shown an expanding range of approaches and applications across a number of disciplines. Despite this increased interest, examination of existing archives of cleared and mounted leaves shows that current methods for mounting, in particular, yield unsatisfactory results and deterioration of samples over relatively short periods. Although techniques for clearing and staining leaves are numerous, published techniques for mounting leaves are scarce. Methods and Results: Here we present a complete protocol and recommendations for clearing, staining, and imaging leaves, and, most importantly, a method to permanently mount cleared leaves. Conclusions: The mounting protocol is faster than other methods, inexpensive, and straightforward; moreover, it yields clear and permanent samples that can easily be imaged, scanned, and stored. Specimens mounted with this method preserve well, with leaves that were mounted more than 35 years ago showing no signs of bubbling or discoloration.

CMS ECAL Endcap (EE) Dee Assembly - SC mounting on Dee 1

CERN Multimedia

Cockerill, D

2007-01-01

Protection panels on back of Dee 1, Completion of SC mounting, 03/10/2007: Completion of SC mounting (aart from the inner 3-2-1)on the first quadrant of Dee 1 and subsequent survey. 22-28/08/2007: The first supercrystals on Dee1, Dee1 in 867 with the first column of SCs ready for mounting, Dee1 with its protection panels over the laser monitoring fibre system

Solar electricity potentials and optimal angles for mounting solar ...

African Journals Online (AJOL)

The need for harnessing solar energy using solar panels mounted at optimal inclination angles in the six geopolitical zones of Nigeria is presented. The optimal angle for mounting solar panels as presented by Photovoltaic Geographic Information System (PVGIS) ranges from 11º to 14º in the Southern zone and 13º to 16º ...

Wind instrument mountings for above-the-cab lookout exposure

Science.gov (United States)

Owen P. Cramer; Ralph H. Moltzau

1968-01-01

The lookout tower offers a ready-made platform from which the speed of true unobstructed wind can be measured, then reduced to equivalent of 20-foot wind. Tower-mounted instruments must meet the requirements of a lightning conductor system, but should also be easily installed and removed for storage and maintenance. Lightweight aluminum mountings for catwalk or flat-...

Key players in neurodegenerative disorders in focus-New insights into the proteomic profile of Alzheimer's disease, schizophrenia, ALS, and multiple sclerosis-24th HUPO BPP Workshop: September 29, 2015, Vancouver, Canada.

Science.gov (United States)

Schrötter, Andreas; Park, Young Mok; Marcus, Katrin; Martins-de-Souza, Daniel; Nilsson, Peter; Magraoui, Fouzi El; Meyer, Helmut E; Grinberg, Lea T

2016-04-01

The HUPO Brain Proteome Project (HUPO BPP) held its 24th workshop in Vancouver, Canada, September 29, 2015. The focus of the autumn workshop was on new insights into the proteomic profile of Alzheimer's disease, schizophrenia, ALS and multiple sclerosis. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

IAS Towards an HIV Cure Symposium: people focused, science driven: 18-19 July 2015, Vancouver, Canada.

Science.gov (United States)

Fidler, Sarah; Thornhill, John; Malatinkova, Eva; Reinhard, Robert; Lamplough, Rosanne; Ananworanich, Jintanat; Chahroudi, Ann

2015-10-01

The International AIDS Society (IAS) convened the Towards an HIV Cure Symposium on 18-19 July 2015 in Vancouver, Canada, bringing together researchers and community to discuss the most recent advances in our understanding of HIV latency, reservoirs and a summary of the current clinical approaches towards an HIV cure. The symposium objectives were to: (1) gather researchers and stakeholders to present, review, and discuss the latest research towards an HIV cure; (2) promote cross-disciplinary global interactions between basic, clinical and social scientists; and (3) provide a platform for sharing information among scientists, clinicians, funders, media and civil society. The symposium examined basic molecular science and animal model data, and emerging and ongoing clinical trial results to prioritise strategies and determine the viral and immune responses that could lead to HIV remission without antiretroviral therapy. This report summarises some of the major findings discussed during the symposium.

75 FR 71139 - Land Acquisitions; Puyallup Tribe of Washington

Science.gov (United States)

2010-11-22

... Auditor, in Pierce County, Washington. Except that portion of Lot 3 conveyed to the State of Washington by Deeds recorded under Auditor's file number 689865 and 689858. Together with the East half of the... amendment of Short Plat Nos. 8502210395 and 8403080186, filed with the Pierce County Auditor, in Pierce...

Mount St. Helens aerosol evolution

Energy Technology Data Exchange (ETDEWEB)

Oberbeck, V.R.; Farlow, N.H.

1982-08-01

Stratospheric aerosol samples were collected using a wire impactor during the year following the eruption of Mount St. Helens. Analysis of samples shows that aerosol volume increased for 6 months due to gas-to-particle conversion and then decreased to background levels in the following 6 months.

Monitoring lava-dome growth during the 2004-2008 Mount St. Helens, Washington, eruption using oblique terrestrial photography

Science.gov (United States)

Major, J.J.; Dzurisin, D.; Schilling, S.P.; Poland, Michael P.

2009-01-01

We present an analysis of lava dome growth during the 2004–2008 eruption of Mount St. Helens using oblique terrestrial images from a network of remotely placed cameras. This underutilized monitoring tool augmented more traditional monitoring techniques, and was used to provide a robust assessment of the nature, pace, and state of the eruption and to quantify the kinematics of dome growth. Eruption monitoring using terrestrial photography began with a single camera deployed at the mouth of the volcano's crater during the first year of activity. Analysis of those images indicates that the average lineal extrusion rate decayed approximately logarithmically from about 8 m/d to about 2 m/d (± 2 m/d) from November 2004 through December 2005, and suggests that the extrusion rate fluctuated on time scales of days to weeks. From May 2006 through September 2007, imagery from multiple cameras deployed around the volcano allowed determination of 3-dimensional motion across the dome complex. Analysis of the multi-camera imagery shows spatially differential, but remarkably steady to gradually slowing, motion, from about 1–2 m/d from May through October 2006, to about 0.2–1.0 m/d from May through September 2007. In contrast to the fluctuations in lineal extrusion rate documented during the first year of eruption, dome motion from May 2006 through September 2007 was monotonic (± 0.10 m/d) to gradually slowing on time scales of weeks to months. The ability to measure spatial and temporal rates of motion of the effusing lava dome from oblique terrestrial photographs provided a significant, and sometimes the sole, means of identifying and quantifying dome growth during the eruption, and it demonstrates the utility of using frequent, long-term terrestrial photography to monitor and study volcanic eruptions.

Fire-climate-human interactions during the postglacial period at Sunrise Ridge, Mount Rainier National Park, Washington (USA)

Science.gov (United States)

Walsh, Megan K.; Lukens, Michael L.; McCutcheon, Patrick T.; Burtchard, Greg C.

2017-12-01

With the creation of Mount Rainier National Park (MORA) in 1899 came the active management of the park's landscapes and a heavy emphasis on fire suppression. Today, managers at MORA seek to better manage current fire activity; however, this requires an improved understanding of past fire activity on the mountain. In this study high-resolution macroscopic charcoal analysis and pollen analysis of lake sediment records was used to reconstruct the postglacial fire and vegetation history for the Sunrise Ridge area of MORA. Fire activity was lowest during the Late Glacial when vegetation was sparse and climate was cool and dry. Fire activity increased during the early Holocene as the regional climate warmed and dried, and burnable biomass became more abundant. Fire activity continued to increase into the middle Holocene (until ca. 6600 cal yr BP) even as the regional climate became wetter and eventually cooler; the modern-day mesic forest and subalpine meadow landscapes of the park established at this time. Fire activity was generally highest and mean fire return intervals were lowest on Sunrise Ridge during the late Holocene, and are consistent with tree-ring based estimates of fire frequency. The similarity between the Sunrise Ridge and other paleofire records in the Pacific Northwest suggests that broad-scale climatic shifts, such as the retreat of the Cordilleran ice sheet and changes in annual insolation, as well as increased interannual climate variability (i.e., drought) particularly in the middle to late Holocene, were responsible for changes in fire activity during the postglacial period. However, abundant and increasing archaeological evidence from Sunrise Ridge during the middle to late Holocene suggests that humans may have also influenced the landscape at this time. It is likely that fires will continue to increase at MORA as drought becomes a more frequent occurrence in the Pacific Northwest.

Educator Supply and Demand in Washington State. 2004 Report

Science.gov (United States)

Lashway, Larry; Maloney, Rick; Hathaway, Randy; Bryant, B. J.

2005-01-01

This report describes the findings of the third Educator Supply and Demand Research study in the State of Washington. The intent of these Washington studies is to provide data to inform and shape decisions and activities in the following ways: (1) Provide useful information for educational policymakers, including the legislature, the State Board…

Trends and determinants of cycling in the Washington, DC region.

Science.gov (United States)

2011-01-01

This report analyzes cycling trends, policies, and commuting in the Washington, DC area. The analysis is divided into two parts. : Part 1 focuses on cycling trends and policies in Washington (DC), Alexandria (VA), Arlington County (VA), Fairfax Count...

Alternative Fuels for Washington's School Buses: A Report to the Washington State Legislature.

Science.gov (United States)

Lyons, John Kim; McCoy, Gilbert A.

This document presents findings of a study that evaluated the use of both propane and compressed natural gas as alternative fuels for Washington State school buses. It discusses air quality improvement actions by state- and federal-level regulators and summarizes vehicle design, development, and commercialization activities by all major engine,…

Male-Male Mounting Behaviour in Free-Ranging Golden Snub-Nosed Monkeys (Rhinopithecus roxellana).

Science.gov (United States)

Fang, Gu; Dixson, Alan F; Qi, Xiao-Guang; Li, Bao-Guo

2018-01-01

An all-male band of golden snub-nosed monkeys (Rhinopithecus roxellana) was observed for 3 months in the Qinling Mountains of China, in order to collect data on the frequencies and contextual significance of male-male mounting behaviour. Mounts occurred in a variety of affiliative, dominance-related and sexual contexts, which differed depending upon the ages of the males involved. Mounting behaviour in this group was mainly initiated by adults. Juveniles mounted each other in affiliative contexts (during play and prior to grooming). Adult males mounted subadult and juvenile partners in a greater variety of sociosexual contexts (dominance/rank-related interactions; reconciliation following agonistic encounters, and sometimes as a prelude to receiving grooming). However, subadults and juveniles were never observed to mount adults. In one dyad, involving an adult male and a subadult partner, mounting was more frequent and prolonged, and included bouts of deep pelvic thrusting. Two mounts resulted in anal intromissions and, in 1 case, the subadult partner exhibited seminal emission. Given that the study took place during the annual mating peak period of R. roxellana, it is possible that this unusual male-male sexual activity was related to the absence of mating opportunities for those adults that were excluded from 1-male units. © 2018 S. Karger AG, Basel.

Two-sensor control in active vibration isolation using hard mounts

NARCIS (Netherlands)

Beijen, M.A.; Tjepkema, D.; van Dijk, J.

To isolate precision machines from floor vibrations, active vibration isolators are often applied. In this paper, a two-sensor control strategy, based on acceleration feedback and force feedback, is proposed for an active vibration isolator using a single-axis active hard mount. The hard mount

Two-sensor control in active vibration isolation using hard mounts

NARCIS (Netherlands)

Beijen, M.A.; Tjepkema, D.; van Dijk, Johannes

2014-01-01

To isolate precision machines from floor vibrations, active vibration isolators are often applied. In this paper, a two-sensor control strategy, based on acceleration feedback and force feedback, is proposed for an active vibration isolator using a single-axis active hard mount. The hard mount

Oversight Hearing on Drug Abuse Education Programs. Hearing before the Subcommittee on Elementary, Secondary, and Vocational Education of the Committee on Education and Labor. House of Representatives, 101st Congress, 2nd Session (Vancouver, Washington, September 6, 1990).

Science.gov (United States)

Congress of the U.S., Washington, DC. House Committee on Education and Labor.

The text of an oversight hearing on Drug Abuse Resistance Education (DARE) programs is presented in this document. Introductory statements by Representatives Jolene Unsoeld and Dale E. Kildee are presented. Testimony by these witnesses is included: (1) Roy Bondurant, student, and Roy "Skip" Bondurant, parent, Tenino, Washington; (2) Paul…

77 FR 11582 - Notice of Inventory Completion: Central Washington University Department of Anthropology...

Science.gov (United States)

2012-02-27

...: Central Washington University Department of Anthropology, Ellensburg, WA AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The Central Washington University Department of Anthropology has... Central Washington University Department of Anthropology. Repatriation of the human remains and associated...

Residential Energy Efficiency Potential: Washington

Energy Technology Data Exchange (ETDEWEB)

Wilson, Eric J [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-11-27

Energy used by Washington single-family homes that can be saved through cost-effective improvements. Prepared by Eric Wilson and Noel Merket, NREL, and Erin Boyd, U.S. Department of Energy Office of Energy Policy and Systems Analysis.

Results of the Washington Passive Solar Design/Build Competition

Energy Technology Data Exchange (ETDEWEB)

Nylen, N.

1981-01-01

In an effort to encourage the design, construction, and marketing of moderately priced passive solar homes in Washington state, the Western Solar Utilization Network (Western SUN) recently sponsored the Washington Passive Solar Design/Build Competition. The competition drew an overwhelming response from designers and builders throughout Washington. Thermal performance of the designs was evaluated by a technical review committee, and final selections were made by the Competition Jury in accordance with the following criteria: perceived market acceptance, thermal performance, cost effectiveness, simplicity of design and operation, and completeness of the passive concept. Design contract awards totaling $50,000 were made available to winners in four categories, including single and multi-family, new and remodeled residences. In order to receive the award in its entirety, winning design/build teams are required to construct their design by April, 1983. As a result of the competition, a great deal was learned about the attitudes and knowledge of professionals and the general public regarding the use of solar energy in Washington state. Among the points that will be highlighted in this paper are the following: (1) a design/build competition is an effective vehicle for promoting solar energy among professionals in the housing community as well as the general public; (2) passive solar techniques can contribute significantly to the heating and cooling needs of residential housing throughout the state of Washington; (3) there is a great deal of interest and talent among the designers and builders of solar residences in Washington; and (4) follow-up activities, including the promotion of winning designs, the systematic collection of performance data, and identification of the major obstacles confronting designers and builders of solar homes, are critical to the success of the program in achieving both its short-term and long-term goals.

77 FR 15802 - Notice of Inventory Completion: Central Washington University Department of Anthropology...

Science.gov (United States)

2012-03-16

...: Central Washington University Department of Anthropology, Ellensburg, WA AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The Central Washington University Department of Anthropology has... contact the Central Washington University Department of Anthropology. Repatriation of the human remains to...

Nozzle Mounting Method Optimization Based on Robot Kinematic Analysis

Science.gov (United States)

Chen, Chaoyue; Liao, Hanlin; Montavon, Ghislain; Deng, Sihao

2016-08-01

Nowadays, the application of industrial robots in thermal spray is gaining more and more importance. A desired coating quality depends on factors such as a balanced robot performance, a uniform scanning trajectory and stable parameters (e.g. nozzle speed, scanning step, spray angle, standoff distance). These factors also affect the mass and heat transfer as well as the coating formation. Thus, the kinematic optimization of all these aspects plays a key role in order to obtain an optimal coating quality. In this study, the robot performance was optimized from the aspect of nozzle mounting on the robot. An optimized nozzle mounting for a type F4 nozzle was designed, based on the conventional mounting method from the point of view of robot kinematics validated on a virtual robot. Robot kinematic parameters were obtained from the simulation by offline programming software and analyzed by statistical methods. The energy consumptions of different nozzle mounting methods were also compared. The results showed that it was possible to reasonably assign the amount of robot motion to each axis during the process, so achieving a constant nozzle speed. Thus, it is possible optimize robot performance and to economize robot energy.

Impact of mounting methods in computerized axiography on assessment of condylar inclination.

Science.gov (United States)

Schierz, Oliver; Wagner, Philipp; Rauch, Angelika; Reissmann, Daniel R

2017-08-30

Valid and reliable recording is a key requirement for accurately simulating individual jaw movements. Horizontal condylar inclination (HCI) and Bennett's angle were measured using a digital jaw tracker (Cadiax® Compact 2) in 27 young adults. Three mounting methods (paraocclusal tray adapter, periocclusal tray adapter, and tray adapter with mandibular clamp) were tested. The mean values of the HCI differed by up to 10° between the mounting methods; however, the values for Bennett's angle did not differ substantially. While the intersession reliability of the Bennett's angle assessment did not depend on the mounting method, the reliability of the HCI assessment was only fair to good for the paraocclusal mounting method but poor for both periocclusal mounting methods. For attaching the tracing bow of jaw trackers to the mandible, a paraocclusal tray adapter should be applied, to achieve the most reliable results.

Calculating the mounting parameters for Taylor Spatial Frame correction using computed tomography.

Science.gov (United States)

Kucukkaya, Metin; Karakoyun, Ozgur; Armagan, Raffi; Kuzgun, Unal

2011-07-01

The Taylor Spatial Frame uses a computer program-based six-axis deformity analysis. However, there is often a residual deformity after the initial correction, especially in deformities with a rotational component. This problem can be resolved by recalculating the parameters and inputting all new deformity and mounting parameters. However, this may necessitate repeated x-rays and delay treatment. We believe that error in the mounting parameters is the main reason for most residual deformities. To prevent these problems, we describe a new calculation technique for determining the mounting parameters that uses computed tomography. This technique is especially advantageous for deformities with a rotational component. Using this technique, exact calculation of the mounting parameters is possible and the residual deformity and number of repeated x-rays can be minimized. This new technique is an alternative method to accurately calculating the mounting parameters.

Astrophotography on the go using short exposures with light mounts

CERN Document Server

Ashley, Joseph

2015-01-01

No longer are heavy, sturdy, expensive mounts and tripods required to photograph deep space. With today's advances in technology, all that is required is an entry-DSLR and an entry level GoTo telescope. Here is all of the information needed to start photographing the night sky without buying expensive tracking mounts. By using multiple short exposures and combining them with mostly ‘freeware’ computer programs, the effect of image rotation can be minimized to a point where it is undetectable in normal astrophotography, even for a deep-sky object such as a galaxy or nebula. All the processes, techniques, and equipment needed to use inexpensive, lightweight altazimuth and equatorial mounts and very short exposures photography to image deep space objects are explained, step-by-step, in full detail, supported by clear, easy to understand graphics and photographs.   Currently available lightweight mounts and tripods are identified and examined from an economic versus capability perspective to help users deter...

Mounting power cables on SOLEIL

CERN Multimedia

Laurent Guiraud

1999-01-01

The power couplers are mounted on the SOLEIL cryomodule in a clean room. The cryomodule will allow superconducting technology to be used at SOLEIL, the French national synchrotron facility. This work is carried out as part of a collaboration between CERN and CEA Saclay, the French National Atomic Energy Commission.

Design of tracking mount and controller for mobile satellite laser ranging system

Science.gov (United States)

Park, Cheol Hoon; Son, Young Su; Kim, Byung In; Ham, Sang Young; Lee, Sung Whee; Lim, Hyung Chul

2012-01-01

In this study, we have proposed and implemented a design for the tracking mount and controller of the ARGO-M (Accurate Ranging system for Geodetic Observation - Mobile) which is a mobile satellite laser ranging (SLR) system developed by the Korea Astronomy and Space Science Institute (KASI) and Korea Institute of Machinery and Materials (KIMM). The tracking mount comprises a few core components such as bearings, driving motors and encoders. These components were selected as per the technical specifications for the tracking mount of the ARGO-M. A three-dimensional model of the tracking mount was designed. The frequency analysis of the model predicted that the first natural frequency of the designed tracking mount was high enough. The tracking controller is simulated using MATLAB/xPC Target to achieve the required pointing and tracking accuracy. In order to evaluate the system repeatability and tracking accuracy of the tracking mount, a prototype of the ARGO-M was fabricated, and repeatability tests were carried out using a laser interferometer. Tracking tests were conducted using the trajectories of low earth orbit (LEO) and high earth orbit (HEO) satellites. Based on the test results, it was confirmed that the prototype of the tracking mount and controller of the ARGO-M could achieve the required repeatability along with a tracking accuracy of less than 1 arcsec.

A Versatile Mounting Method for Long Term Imaging of Zebrafish Development.

Science.gov (United States)

Hirsinger, Estelle; Steventon, Ben

2017-01-26

Zebrafish embryos offer an ideal experimental system to study complex morphogenetic processes due to their ease of accessibility and optical transparency. In particular, posterior body elongation is an essential process in embryonic development by which multiple tissue deformations act together to direct the formation of a large part of the body axis. In order to observe this process by long-term time-lapse imaging it is necessary to utilize a mounting technique that allows sufficient support to maintain samples in the correct orientation during transfer to the microscope and acquisition. In addition, the mounting must also provide sufficient freedom of movement for the outgrowth of the posterior body region without affecting its normal development. Finally, there must be a certain degree in versatility of the mounting method to allow imaging on diverse imaging set-ups. Here, we present a mounting technique for imaging the development of posterior body elongation in the zebrafish D. rerio. This technique involves mounting embryos such that the head and yolk sac regions are almost entirely included in agarose, while leaving out the posterior body region to elongate and develop normally. We will show how this can be adapted for upright, inverted and vertical light-sheet microscopy set-ups. While this protocol focuses on mounting embryos for imaging for the posterior body, it could easily be adapted for the live imaging of multiple aspects of zebrafish development.

75 FR 52023 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2010-08-24

... DEPARTMENT OF THE INTERIOR National Park Service Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of Washington, Seattle, WA AGENCY: National Park Service... of the Thomas Burke Memorial Washington State Museum (Burke Museum), University of Washington...

75 FR 36672 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2010-06-28

... DEPARTMENT OF THE INTERIOR National Park Service Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of Washington, Seattle, WA AGENCY: National Park Service... of the Thomas Burke Memorial Washington State Museum (Burke Museum), University of Washington...

Implications of Dynamic Pressure Transducer Mounting Variations on Measurements in Pyrotechnic Test Apparatus

Science.gov (United States)

Dibbern, Andreas; Crisafulli, Jeffrey; Hagopia, Michael; McDougle, Stephen H.; Saulsberry, Regor L.

2009-01-01

Accurate dynamic pressure measurements are often difficult to make within small pyrotechnic devices, and transducer mounting difficulties can cause data anomalies that lead to erroneous conclusions. Delayed initial pressure response followed by data ringing has been observed when using miniaturized pressure transducer mounting adapters required to interface transducers to small test chambers. This delayed pressure response and ringing, combined with a high data acquisition rate, has complicated data analysis. This paper compares the output signal characteristics from different pressure transducer mounting options, where the passage distance from the transducer face to the pyrotechnic chamber is varied in length and diameter. By analyzing the data and understating the associated system dynamics, a more realistic understanding of the actual dynamic pressure variations is achieved. Three pressure transducer mounting configurations (elongated, standard, and face/flush mount) were simultaneously tested using NASA standard initiators in closed volume pressure bombs. This paper also presents results of these pressure transducer mounting configurations as a result of a larger NASA Engineering and Safety Center pyrovalve test project. Results from these tests indicate the improved performance of using face/flush mounted pressure transducers in this application. This type of mounting improved initial pressure measurement response time by approximately 19 s over standard adapter mounting, eliminating most of the lag time; provided a near step-function type initial pressure increase; and greatly reduced data ringing in high data acquisition rate systems. The paper goes on to discuss other issues associated with the firing and instrumentation that are important for the tester to understand.

Washington State Briefing Book for low-level radioactive waste management

Energy Technology Data Exchange (ETDEWEB)

1980-12-01

The Washington State Briefing Book is one of a series of state briefing books on low-level radioactive waste management practices. It has been prepared to assist state and federal agency officials in planning for safe low-level radioactive waste disposal. The report contains a profile of low-level radioactive waste generators in Washington. The profile is the result of a survey of NRC licensees in Washington. The briefing book also contains a comprehensive assessment of low-level radioactive waste management issues and concerns as defined by all major interested parties including industry, government, the media, and interest groups. The assessment was developed through personal communications with representatives of interested parties, and through a review of media sources. Lastly, the briefing book provides demographic and socioeconomic data and a discussion of relevant government agencies and activities, all of which may impact waste management practices in Washington.

Washington State Briefing Book for low-level radioactive waste management

International Nuclear Information System (INIS)

1980-12-01

The Washington State Briefing Book is one of a series of state briefing books on low-level radioactive waste management practices. It has been prepared to assist state and federal agency officials in planning for safe low-level radioactive waste disposal. The report contains a profile of low-level radioactive waste generators in Washington. The profile is the result of a survey of NRC licensees in Washington. The briefing book also contains a comprehensive assessment of low-level radioactive waste management issues and concerns as defined by all major interested parties including industry, government, the media, and interest groups. The assessment was developed through personal communications with representatives of interested parties, and through a review of media sources. Lastly, the briefing book provides demographic and socioeconomic data and a discussion of relevant government agencies and activities, all of which may impact waste management practices in Washington

Inverse axial mounting stiffness design for lithographic projection lenses.

Science.gov (United States)

Wen-quan, Yuan; Hong-bo, Shang; Wei, Zhang

2014-09-01

In order to balance axial mounting stiffness of lithographic projection lenses and the image quality under dynamic working conditions, an easy inverse axial mounting stiffness design method is developed in this article. Imaging quality deterioration at the wafer under different axial vibration levels is analyzed. The desired image quality can be determined according to practical requirements, and axial vibrational tolerance of each lens is solved with the damped least-squares method. Based on adaptive interval adjustment, a binary search algorithm, and the finite element method, the axial mounting stiffness of each lens can be traveled in a large interval, and converges to a moderate numerical solution which makes the axial vibrational amplitude of the lens converge to its axial vibrational tolerance. Model simulation is carried out to validate the effectiveness of the method.

A Portable Shoulder-Mounted Camera System for Surgical Education in Spine Surgery.

Science.gov (United States)

Pham, Martin H; Ohiorhenuan, Ifije E; Patel, Neil N; Jakoi, Andre M; Hsieh, Patrick C; Acosta, Frank L; Wang, Jeffrey C; Liu, John C

2017-02-07

The past several years have demonstrated an increased recognition of operative videos as an important adjunct for resident education. Currently lacking, however, are effective methods to record video for the purposes of illustrating the techniques of minimally invasive (MIS) and complex spine surgery. We describe here our experiences developing and using a shoulder-mounted camera system for recording surgical video. Our requirements for an effective camera system included wireless portability to allow for movement around the operating room, camera mount location for comfort and loupes/headlight usage, battery life for long operative days, and sterile control of on/off recording. With this in mind, we created a shoulder-mounted camera system utilizing a GoPro™ HERO3+, its Smart Remote (GoPro, Inc., San Mateo, California), a high-capacity external battery pack, and a commercially available shoulder-mount harness. This shoulder-mounted system was more comfortable to wear for long periods of time in comparison to existing head-mounted and loupe-mounted systems. Without requiring any wired connections, the surgeon was free to move around the room as needed. Over the past several years, we have recorded numerous MIS and complex spine surgeries for the purposes of surgical video creation for resident education. Surgical videos serve as a platform to distribute important operative nuances in rich multimedia. Effective and practical camera system setups are needed to encourage the continued creation of videos to illustrate the surgical maneuvers in minimally invasive and complex spinal surgery. We describe here a novel portable shoulder-mounted camera system setup specifically designed to be worn and used for long periods of time in the operating room.

Semi-active engine mount design using auxiliary magneto-rheological fluid compliance chamber

Science.gov (United States)

Mansour, H.; Arzanpour, S.; Golnaraghi, M. F.; Parameswaran, A. M.

2011-03-01

Engine mounts are used in the automotive industry to isolate engine and chassis by reducing the noise and vibration imposed from one to the other. This paper describes modelling, simulation and design of a semi-active engine mount that is designed specifically to address the complicated vibration pattern of variable displacement engines (VDE). The ideal isolation for VDE requires the stiffness to be switchable upon cylinder activation/deactivation operating modes. In order to have a modular design, the same hydraulic engine mount components are maintained and a novel auxiliary magneto-rheological (MR) fluid chamber is developed and retrofitted inside the pumping chamber. The new compliance chamber is a controllable pressure regulator, which can effectively alter the dynamic performance of the mount. Switching between different modes happens by turning the electrical current to the MR chamber magnetic coil on and off. A model has been developed for the passive hydraulic mount and then it is extended to include the MR auxiliary chamber as well. A proof-of-concept prototype of the design has been fabricated which validates the mathematical model. The results demonstrate unique capability of the developed semi-active mount to be used for VDE application.

77 FR 51564 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2012-08-24

... Inventory Completion: Thomas Burke Memorial Washington State Museum, University of Washington, Seattle, WA AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The Thomas Burke Memorial Washington... of human remains under the control of the Thomas Burke Memorial Washington State Museum (Burke Museum...

Environmental disturbance and conservation of marine and shoreline birds on the west coast of Vancouver Island

International Nuclear Information System (INIS)

Morgan, K.H.; Butler, R.W.; Vermeer, R.W.

1992-01-01

Loss of habitat and oiling of birds represent two major threats to marine and shoreline bird populations on Vancouver Island's west coast, since their effects are widespread and cumulative. Offshore tanker traffic and local inshore shipments of petroleum products expose the coast to high risks of oiling. Large numbers of birds are most at risk when concentrated in relatively small areas, such as highly productive feeding areas, at communal roosting sites, and around nesting colonies. Logging of mature and old-growth forests has led to destruction of the nesting habitat of marbled murrelets (Brachyramphus marmoratus), while industrial development of estuaries, mudflats, and spawning grounds of Pacific herring (Clupea harengus pallasi) has diminished feeding habitats for other marine and shoreline birds. Fisheries operations, human disturbance of colonies, and introduced predators, notably the raccoon (Procyon lotor) and mink (Mustela vison), have impacted upon local populations. Management actions and research needs to mitigate these threats are addressed. 40 refs

77 FR 50157 - Notice of Public Meeting, Eastern Washington Resource Advisory Council Meeting

Science.gov (United States)

2012-08-20

...; HAG 12-0260] Notice of Public Meeting, Eastern Washington Resource Advisory Council Meeting AGENCY.... Department of the Interior, Bureau of Land Management (BLM) Eastern Washington Resource Advisory Council... Bureau of Land Management's Eastern Washington and San Juan Resource Management Plan and the U.S. Forest...

Vertically mounted bifacial photovoltaic modules: A global analysis

International Nuclear Information System (INIS)

Guo, Siyu; Walsh, Timothy Michael; Peters, Marius

2013-01-01

Bifacial PV (photovoltaic) modules have recently come to increasing attention and various system designs have been investigated. In this paper, a global comparison is made between vertically mounted bifacial modules facing East–West and conventionally mounted mono-facial modules. An analytical method is used to calculate the radiation received by these two module configurations. It is found that the answer to the question which of these two module configurations performs better strongly depends on three factors: (i) the latitude, (ii) the local diffuse fraction and (iii) the albedo. In a subsequent part of the paper, the minimum albedo required to result in a better performance for vertically mounted bifacial modules is calculated for every place in the world. The calculation is based on measured data of the diffuse light fraction and the results are shown in the form of a global map. Finally, the albedo requirements are compared with the measured global albedo distribution. The calculation allows a distinct decision which module configuration is more suitable for a certain place in the world. The result is also shown as a map defining the corresponding areas. - Highlights: • Vertically mounted bifacial module and conventionally monofacial module are compared. • The key factors affecting the performance of the two configurations are investigated. • Which module configuration is more suitable for each place is shown in a world map. • The minimum albedo for bifacial modules to have a better performance is calculated

A Study on quality improvement and application technology in pad-mounted transformers

Energy Technology Data Exchange (ETDEWEB)

Kim, Soon Tae; Mun, Kyung Hwa; Jung, Dong Won; Kim, Sang Jun; Lee, Nam Woo; Kang, Nae Kuk; Kim, Dong Mung [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center; Kim, Kwang Ha; Kang, Young Sik; Lee, Woo Young; Lyu, Hee Suk; Sun, Jong Ho; Lyu, Hyung Ki; Kim, Yik Soo; Park, Sung Jae; Kim, Won Ho [Korea Electrotechnology Research Inst., Changwon (Korea, Republic of)

1995-12-31

In order to increase the reliability of pad-mounted transformers, the authors investigated operating condition of pad-mounted transformers and understood their failure mechanisms. The objective of their study was to improve quality and operating condition and install switches to be able to check and maintain transformers and optimise protection devices and increase cooling effect in pad-mounted transformers (author). 65 refs., 130 figs.

Remembering George Washington: What Do Instructional Materials Teach Us about Washington's Patriotism?

Science.gov (United States)

Fitzgerald, Jason C.

2011-01-01

History textbooks have long been criticized for their adherence to the "stabilized national narrative" (VanSledright 1998). However, teachers need to also be aware of the ideological influences of the supplemental instructional materials they choose. A case study of the Donald W. Reynolds Museum and Education Center at Mount Vernon illustrates…

Preparation of samples for leaf architecture studies, a method for mounting cleared leaves1

Science.gov (United States)

Vasco, Alejandra; Thadeo, Marcela; Conover, Margaret; Daly, Douglas C.

2014-01-01

• Premise of the study: Several recent waves of interest in leaf architecture have shown an expanding range of approaches and applications across a number of disciplines. Despite this increased interest, examination of existing archives of cleared and mounted leaves shows that current methods for mounting, in particular, yield unsatisfactory results and deterioration of samples over relatively short periods. Although techniques for clearing and staining leaves are numerous, published techniques for mounting leaves are scarce. • Methods and Results: Here we present a complete protocol and recommendations for clearing, staining, and imaging leaves, and, most importantly, a method to permanently mount cleared leaves. • Conclusions: The mounting protocol is faster than other methods, inexpensive, and straightforward; moreover, it yields clear and permanent samples that can easily be imaged, scanned, and stored. Specimens mounted with this method preserve well, with leaves that were mounted more than 35 years ago showing no signs of bubbling or discoloration. PMID:25225627

Vancouver Coastal Health's Second Generation Health Strategy: A need for a reboot?

Science.gov (United States)

Masuda, Jeffrey R; Chan, Sophy

2017-03-01

In this commentary, we consider the motivations and implications of Vancouver Coastal Health's place-based population health strategy called the Downtown Eastside Second Generation Health Strategy (2GHS) in light of a broader historical view of shifting values in population and public health and structural health reforms in Canada over the past three decades. We argue that the tone and content of the 2GHS signals a shift towards a neoliberal clientelist model of health that treats people as patients and the DTES as a site of clinical encounter rather than as a community in its own right. In its clinical emphasis, the 2GHS fails to recognize the political dimension of health and well-being in the DTES, a community that faces compounding health risks associated with colonialism, gentrification, human displacement, the criminalization of poverty, sex work, and the street economy. Furthermore, we suggest that in its emphasis on allocating funding based on a rationalist model of health system access, the 2GHS undermines well-established insights and best practices from community-driven health initiatives. Our aim is to provide a provocation that will encourage public health policy-makers to embrace community-based leadership as well as the broader structural health determinants that are at the root of the current circumstances of people in the DTES and other marginalized communities in Canada.

Vancouver Olympic rings powered by fuel cell and IESO records winning goal

Energy Technology Data Exchange (ETDEWEB)

Anon.

2010-04-15

The fuel cell system that provided power to the 30-foot tall floating Olympic Rings in Vancouver's harbour during the 2010 Winter Olympic Games was developed and manufactured by IdaTech in Bend, Oregon. The power source altered between a biodiesel generator and IdaTech's ElectraGen H2 zero emission hydrogen fuel cell system. The technology was chosen as a source of reliable, clean energy for applications in remote locations. The ElectraGen H2 is a hydrogen fueled proton exchange membrane (PEM) fuel cell system that emits only water vapour and heat, without any greenhouse gases. These solid state electric generators combine the best features of generators and batteries. IdaTech has sold over 400 of these fuel cell units to India and Asia to provide backup power to telecommunications networks. The 2010 Winter Olympic Games also provided an opportunity for Ontario's Independent Electricity System Operator (IESO) to track electricity consumption as people turned on their televisions to watch the Men's hockey final between Canada and the United States. An increase in electricity use of 300 MW occurred just before the game started and a similar increase occurred during the intermissions as viewers prepared snacks. Electricity consumption dropped considerably after overtime began and then climbed in the final stages of the game after the winning goal was scored. 2 figs.

Clean air benefits and costs in the GVRD [Greater Vancouver Regional District

International Nuclear Information System (INIS)

Gislason, G.; Martin, J.; Williams, D.; Caton, B.; Rich, J.; Rojak, S.; Robinson, J.; Stuermer, A. von

1994-01-01

Air pollution is a major concern in the Greater Vancouver Regional District in British Columbia. An analysis was conducted to assess the costs and benefits of an innovative plan to reduce the emissions of five primary pollutants in the GVRD: nitrogen oxides (NOx), sulfur oxides (SOx), volatile organic compounds (VOCs), particulates, and CO. The study adopts a damage function approach in which the benefits of reduced emissions are given by the averted damages to human health, crops, and so on. Under a base case scenario, motor vehicle emission controls and additional measures proposed in the region's air quality management plan (AQMP) are projected to lead to emission reductions of 873,000 tonnes in the GVRD by the year 2020, compared to the emission level projected without intervention. The AQMP is projected to avert over its life some 2,800 premature deaths, 33,000 emergency room visits, 13 million restricted activity days, and 5 million symptoms. Crop losses due to ozone are projected to decrease by 1-4%/y over the next several decades due to the AQMP. Damage averted to materials and property per tonne of pollutant reduced ranges from $30 for VOC to $180 for particulates. Under base-case conservative assumptions, the AQMP generates $5.4 billion in benefits and $3.8 billion in costs, nearly 2/3 of which are paid by the industrial and commercial sectors. 1 tab

Shock Mounting for Heavy Machines

Science.gov (United States)

Thompson, A. R.

1984-01-01

Elastomeric bearings eliminate extraneous forces. Rocket thrust transmitted from motor to load cells via support that absorbs extraneous forces so they do not affect accuracy of thrust measurements. Adapter spoked cone fits over forward end of rocket motor. Shock mounting developed for rocket engines under test used as support for heavy machines, bridges, or towers.

77 FR 23495 - Notice of Public Meeting, Eastern Washington Resource Advisory Council Meeting

Science.gov (United States)

2012-04-19

...; HAG 12-0164] Notice of Public Meeting, Eastern Washington Resource Advisory Council Meeting AGENCY... 1972, the U.S. Department of the Interior, Bureau of Land Management (BLM) Eastern Washington Resource... of Land Management's Eastern Washington and San Juan Resource Management Plan, and the U.S. Forest...

Square Van Atta reflector with conducting mounting flame

DEFF Research Database (Denmark)

Nielsen, Erik Dragø

1970-01-01

A theoretical and numerical analysis of square Van Atta reflectors has been carried out with or without a conducting plate, used for mounting of the antenna elements. The Van Atta reflector investigated has antenna elements which are parallel half-wave dipoles interconnected in pairs by transmiss......A theoretical and numerical analysis of square Van Atta reflectors has been carried out with or without a conducting plate, used for mounting of the antenna elements. The Van Atta reflector investigated has antenna elements which are parallel half-wave dipoles interconnected in pairs...

Heat-related illness in Washington State agriculture and forestry sectors.

Science.gov (United States)

Spector, June T; Krenz, Jennifer; Rauser, Edmund; Bonauto, David K

2014-08-01

We sought to describe heat-related illness (HRI) in agriculture and forestry workers in Washington State. Demographic and clinical Washington State Fund workers' compensation agriculture and forestry HRI claims data (1995-2009) and Washington Agriculture Heat Rule citations (2009-2012) were accessed and described. Maximum daily temperature (Tmax) and Heat Index (HImax) were estimated by claim date and location using AgWeatherNet's weather station network. There were 84 Washington State Fund agriculture and forestry HRI claims and 60 Heat Rule citations during the study period. HRI claims and citations were most common in crop production and support subsectors. The mean Tmax (HImax) was 95°F (99°F) for outdoor HRI claims. Potential HRI risk factors and HRI-related injuries were documented for some claims. Agriculture and forestry HRI cases are characterized by potential work-related, environmental, and personal risk factors. Further work is needed to elucidate the relationship between heat exposure and occupational injuries. © 2014 Wiley Periodicals, Inc.

The seed plant flora of the Mount Jinggangshan region, southeastern China.

Directory of Open Access Journals (Sweden)

Lei Wang

Full Text Available The Mount Jinggangshan region is located between Jiangxi and Hunan provinces in southeastern China in the central section of the Luoxiao Mountains. A detailed investigation of Mount Jinggangshan region shows that the seed plant flora comprises 2,958 species in 1,003 genera and 210 families (Engler's system adjusted according to Zhengyi Wu's concept. Among them, 23 species of gymnospermae belong to 17 genera and 9 families, and 2,935 species of angiosperms are in 986 genera and 201 families. Moreover, they can also be sorted into woody plants (350 genera and 1,295 species and herbaceous plants (653 genera and 1,663 species. The dominant families are mainly Fagaceae, Lauraceae, Theaceae, Hamamelidaceae, Magnoliaceae, Ericaceae, Styracaceae, Aquifoliaceae, Elaeocarpaceae, Aceraceae, Rosaceae, Corylaceae, Daphniphyllaceae, Symplocaceae, Euphorbiaceae, Pinaceae, Taxodiaceae, Cupressaceae and Taxaceae. Ancient and relic taxa include Ginkgo biloba, Fokieniahodginsii, Amentotaxusargotaenia, Disanthuscercidifolia subsp. longipes, Hamamelismollis, Manglietiafordiana, Magnoliaofficinalis, Tsoongiodendronodorum, Fortuneariasinensis, Cyclocaryapaliurus, Eucommiaulmoides, Sargentodoxacuneata, Bretschneiderasinensis, Camptothecaacuminata, Tapisciasinensis, etc. The flora of Mount Jinggangshan region includes 79 cosmopolitan genera and 924 non-cosmopolitan genera, which are 7.88% and 92.12% of all genera. The latter includes 452 tropical genera (48.92% and 472 temperate genera (51.08%. The temperate elements include 44 genera endemic to China, accounting for 4.76% of all genera. Among 1,003 genera, 465 have only a single species and 401 are oligotypic genera (with 2-5 species. These genera account for 86.34% of all genera. The floristic analysis indicates that the flora of Mount Jinggangshan region is closely related to the flora of Mount Wuyishan region in southeastern China. The flora of Mount Jinggangshan region also contains many elements of central and

A method of mounting multiple otoliths for beam-based microchemical analyses

Science.gov (United States)

Donohoe, C.J.; Zimmerman, C.E.

2010-01-01

Beam-based analytical methods are widely used to measure the concentrations of elements and isotopes in otoliths. These methods usually require that otoliths be individually mounted and prepared to properly expose the desired growth region to the analytical beam. Most analytical instruments, such as LA-ICPMS and ion and electron microprobes, have sample holders that will accept only one to six slides or mounts at a time. We describe a method of mounting otoliths that allows for easy transfer of many otoliths to a single mount after they have been prepared. Such an approach increases the number of otoliths that can be analyzed in a single session by reducing the need open the sample chamber to exchange slides-a particularly time consuming step on instruments that operate under vacuum. For ion and electron microprobes, the method also greatly reduces the number of slides that must be coated with an electrical conductor prior to analysis. In this method, a narrow strip of cover glass is first glued at one end to a standard microscope slide. The otolith is then mounted in thermoplastic resin on the opposite, free end of the strip. The otolith can then be ground and flipped, if needed, by reheating the mounting medium. After otolith preparation is complete, the cover glass is cut with a scribe to free the otolith and up to 20 small otoliths can be arranged on a single petrographic slide. ?? 2010 The Author(s).

Reaching Higher. A Parent's Guide to the Washington Assessment of Learning. Revised = Para llegar mas arriba. Una guia para padres sobre la evaluacion del aprendizaje de los estudiantes del estado de Washington (Washington Assessment of Student Learning). Revisado.

Science.gov (United States)

Washington Office of the State Superintendent of Public Instruction, Olympia.

This guide in English and Spanish is designed to answer questions parents may have about the Washington Assessment of Student Learning (WASL), including how it will help improve their children's education, how it is scored, and how to use the information it provides. In Washington, clear educational goals for subject content, thinking skills, and…

Using wintergreen oil for mounting mosquito larvae: a safer alternative to xylene.

Science.gov (United States)

Koay, J B; Natasya, N N; Nashithatul, Mag; Ihsanuddin, R; Salleh, F M; Azil, A H

2016-01-01

Permanent mounting of fourth instar mosquito larvae is essential for identifying Aedes spp. This procedure requires extensive exposure to xylene, a clearing agent in the mounting process. We investigated wintergreen oil as a substitute for xylene. Five hundred larvae were mounted on slides to evaluate shrinkage or expansion of specimens after clearing using xylene or wintergreen oil. We examined the ventral brush and siphonal hair tufts for species identification and for preservation of morphological characteristics after clearing specimens in xylene or wintergreen oil. Shrinkage of the length of whole larvae and width of the head, thorax and abdomen after mounting was significantly greater after clearing with xylene than with wintergreen oil. The length of the comb scale nearest the ventral brush was similar for both clearing agents. The clarity of the specimens after mounting was improved by clearing with wintergreen oil, but the integrity of the ventral brush and siphonal hair tufts were similar for both clearing agents.

Field-trip guide to Mount St. Helens, Washington - An overview of the eruptive history and petrology, tephra deposits, 1980 pyroclastic density current deposits, and the crater

Science.gov (United States)

Pallister, John S.; Clynne, Michael A.; Wright, Heather M.; Van Eaton, Alexa R.; Vallance, James W.; Sherrod, David R.; Kokelaar, B. Peter

2017-08-02

This field trip will provide an introduction to several fascinating features of Mount St. Helens. The trip begins with a rigorous hike of about 15 km from the Johnston Ridge Observatory (9 km north-northeast of the crater vent), across the 1980 Pumice Plain, to Windy Ridge (3.6 km northeast of the crater vent) to examine features that document the dynamics and progressive emplacement of pyroclastic flows. The next day, we examine classic tephra outcrops of the past 3,900 years and observe changes in thickness and character of these deposits as we traverse their respective lobes. We examine clasts in the deposits and discuss how the petrology and geochemistry of Mount St. Helens deposits reveal the evolution of the magmatic system through time. We also investigate the stratigraphy of the 1980 blast deposit and review the chronology of this iconic eruption as we travel through the remains of the blown-down forest. The third day is another rigorous hike, about 13 km round trip, climbing from the base of Windy Ridge (elevation 1,240 m) to the front of the Crater Glacier (elevation 1,700 m). En route we examine basaltic andesite and basalt lava flows emplaced between 1,800 and 1,700 years before present, a heterolithologic flow deposit produced as the 1980 blast and debris avalanche interacted, debris-avalanche hummocks that are stranded on the north flank and in the crater mouth, and shattered dacite lava domes that were emplaced between 3,900 and 2,600 years before present. These domes underlie the northern part of the volcano. In addition, within the crater we traverse well-preserved pyroclastic-flow deposits that were emplaced on the crater floor during the summer of 1980, and a beautiful natural section through the 1980 deposits in the upper canyon of the Loowit River.Before plunging into the field-trip log, we provide an overview of Mount St. Helens geology, geochemistry, petrology, and volcanology as background. The volcano has been referred to as a �

June 1992 Mount Spurr, USA Images

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Following 39 years of inactivity, Crater Peak vent on the south flank of Mount Spurr volcano burst into eruption at 7:04 a.m. Alaska daylight time (ADT) on June 27,...

Real-time electrocardiogram transmission from Mount Everest during continued ascent.

Science.gov (United States)

Kao, Wei-Fong; Huang, Jyh-How; Kuo, Terry B J; Chang, Po-Lun; Chang, Wen-Chen; Chan, Kuo-Hung; Liu, Wen-Hsiung; Wang, Shih-Hao; Su, Tzu-Yao; Chiang, Hsiu-chen; Chen, Jin-Jong

2013-01-01

The feasibility of a real-time electrocardiogram (ECG) transmission via satellite phone from Mount Everest to determine a climber's suitability for continued ascent was examined. Four Taiwanese climbers were enrolled in the 2009 Mount Everest summit program. Physiological measurements were taken at base camp (5300 m), camp 2 (6400 m), camp 3 (7100 m), and camp 4 (7950 m) 1 hour after arrival and following a 10 minute rest period. A total of 3 out of 4 climbers were able to summit Mount Everest successfully. Overall, ECG and global positioning system (GPS) coordinates of climbers were transmitted in real-time via satellite phone successfully from base camp, camp 2, camp 3, and camp 4. At each camp, Resting Heart Rate (RHR) was transmitted and recorded: base camp (54-113 bpm), camp 2 (94-130 bpm), camp 3 (98-115 bpm), and camp 4 (93-111 bpm). Real-time ECG and GPS coordinate transmission via satellite phone is feasible for climbers on Mount Everest. Real-time RHR data can be used to evaluate a climber's physiological capacity to continue an ascent and to summit.

Episodic intrusion, internal differentiation, and hydrothermal alteration of the miocene tatoosh intrusive suite south of Mount Rainier, Washington

Science.gov (United States)

du Bray, E.A.; Bacon, C.R.; John, D.A.; Wooden, J.L.; Mazdab, F.K.

2011-01-01

The Miocene Tatoosh intrusive suite south of Mount Rainier is composed of three broadly granodioritic plutons that are manifestations of ancestral Cascades arc magmatism. Tatoosh intrusive suite plutons have individually diagnostic characteristics, including texture, mineralogy, and geochemistry, and apparently lack internal contacts. New ion-microprobe U-Pb zircon ages indicate crystallization of the Stevens pluton ca. 19.2 Ma, Reflection-Pyramid pluton ca. 18.5 Ma, and Nisqually pluton ca. 17.5 Ma. The Stevens pluton includes rare, statistically distinct ca. 20.1 Ma zircon antecrysts. Wide-ranging zircon rare earth element (REE), Hf, U, and Th concentrations suggest late crystallization from variably evolved residual liquids. Zircon Eu/Eu*-Hf covariation is distinct for each of the Reflection-Pyramid, Nisqually, and Stevens plutons. Although most Tatoosh intrusive suite rocks have been affected by weak hydrothermal alteration, and sparse mineralized veins cut some of these rocks, significant base or precious metal mineralization is absent. At the time of shallow emplacement, each of these magma bodies was largely homogeneous in bulk composition and petrographic features, but, prior to final solidification, each of the Tatoosh intrusive suite plutons developed internal compositional variation. Geochemical and petrographic trends within each pluton are most consistent with differential loss of residual melt, possibly represented by late aplite dikes or erupted as rhyolite, from crystal-rich magma. Crystal-rich magma that formed each pluton evidently accumulated in reservoirs below the present level of exposure and then intruded to a shallow depth. Assembled by episodic intrusion, the Tatoosh intrusive suite may be representative of midsized composite plutonic complexes beneath arc volcanoes. ?? 2011 Geological Society of America.

After the disaster: the hydrogeomorphic, ecological, and biological responses to the 1980 eruption of Mount St. Helens, Washington

Science.gov (United States)

Major, Jon J.; Crisafulli, Charlie; Bishop, John

2009-01-01

The 1980 eruption of Mount St. Helens caused instantaneous landscape disturbance on a grand scale. On 18 May 1980, an ensemble of volcanic processes, including a debris avalanche, a directed pyroclastic density current, voluminous lahars, and widespread tephra fall, abruptly altered landscape hydrology and geomorphology, and created distinctive disturbance zones having varying impacts on regional biota. Response to the geological and ecological disturbances has been varied and complex. In general, eruption-induced alterations in landscape hydrology and geomorphology led to enhanced stormflow discharge and sediment transport. Although the hydrological response to landscape perturbation has diminished, enhanced sediment transport persists in some basins. In the nearly 30 years since the eruption, 350 million (metric) tons of suspended sediment has been delivered from the Toutle River watershed to the Cowlitz River (roughly 40 times the average annual preeruption suspended-sediment discharge of the Columbia River). Such prodigious sediment loading has wreaked considerable socioeconomic havoc, causing significant channel aggradation and loss of flood conveyance capacity. Significant and ongoing engineering efforts have been required to mitigate these problems. The overall biological evolution of the eruption-impacted landscape can be viewed in terms of a framework of survivor legacies. Despite appearances to the contrary, a surprising number of species survived the eruption, even in the most heavily devastated areas. With time, survivor “hotspots” have coalesced into larger patches, and have served as stepping stones for immigrant colonization. The importance of biological legacies will diminish with time, but the intertwined trajectories of geophysical and biological successions will influence the geological and biological responses to the 1980 eruption for decades to come.

Design and vibration control of vehicle engine mount activated by MR fluid and piezoelectric actuator

Science.gov (United States)

Lee, D. Y.; Park, Y. K.; Choi, S. B.; Lee, H. G.

2009-07-01

An engine is one of the most dominant noise and vibration sources in vehicle systems. Therefore, in order to resolve noise and vibration problems due to engine, various types of engine mounts have been proposed. This work presents a new type of active engine mount system featuring a magneto-rheological (MR) fluid and a piezostack actuator. As a first step, six degrees-of freedom dynamic model of an in-line four-cylinder engine which has three points mounting system is derived by considering the dynamic behaviors of MR mount and piezostack mount. In the configuration of engine mount system, two MR mounts are installed for vibration control of roll mode motion whose energy is very high in low frequency range, while one piezostack mount is installed for vibration control of bounce and pitch mode motion whose energy is relatively high in high frequency range. As a second step, linear quadratic regulator (LQR) controller is synthesized to actively control the imposed vibration. In order to demonstrate the effectiveness of the proposed active engine mount, vibration control performances are evaluated under various engine operating speeds (wide frequency range).

Marijuana, other drugs, and alcohol use by drivers in Washington State.

Science.gov (United States)

2016-07-01

In Washington State legal sales of marijuana began July 8, 2014. A voluntary, anonymous roadside study was conducted to assess the prevalence of drivers testing positive for alcohol and other drugs, including marijuana, on Washingtons roads. Data ...

Dynamic characteristics of mirrors' kinematic mount

International Nuclear Information System (INIS)

Wu Wenkai; Du Qiang; Li Jingze; Chen Gang; Chen Xiaojuan; Xu Yuanli

2002-01-01

Applying exact constrain design principles, kinematic mount for precision positioning large aperture mirrors is designed; theoretical method is introduced to analyze its dynamic characteristics and the result of the experiment for mirrors, stability; accordingly, the methods to improve design are put forward

Lifetime Doctor-Diagnosed Mental Health Conditions and Current Substance Use Among Gay and Bisexual Men Living in Vancouver, Canada.

Science.gov (United States)

Lachowsky, Nathan J; Dulai, Joshun J S; Cui, Zishan; Sereda, Paul; Rich, Ashleigh; Patterson, Thomas L; Corneil, Trevor T; Montaner, Julio S G; Roth, Eric A; Hogg, Robert S; Moore, David M

2017-05-12

Studies have found that gay, bisexual, and other men who have sex with men (GBM) have higher rates of mental health conditions and substance use than heterosexual men, but are limited by issues of representativeness. To determine the prevalence and correlates of mental health disorders among GBM in Metro Vancouver, Canada. From 2012 to 2014, the Momentum Health Study recruited GBM (≥16 years) via respondent-driven sampling (RDS) to estimate population parameters. Computer-assisted self-interviews (CASI) collected demographic, psychosocial, and behavioral information, while nurse-administered structured interviews asked about mental health diagnoses and treatment. Multivariate logistic regression using manual backward selection was used to identify covariates for any lifetime doctor diagnosed: (1) alcohol/substance use disorder and (2) any other mental health disorder. Of 719 participants, 17.4% reported a substance use disorder and 35.2% reported any other mental health disorder; 24.0% of all GBM were currently receiving treatment. A lifetime substance use disorder diagnosis was negatively associated with being a student (AOR = 0.52, 95% CI [confidence interval]: 0.27-0.99) and an annual income ≥$30,000 CAD (AOR = 0.38, 95% CI: 0.21-0.67) and positively associated with HIV-positive serostatus (AOR = 2.54, 95% CI: 1.63-3.96), recent crystal methamphetamine use (AOR = 2.73, 95% CI: 1.69-4.40) and recent heroin use (AOR = 5.59, 95% CI: 2.39-13.12). Any other lifetime mental health disorder diagnosis was negatively associated with self-identifying as Latin American (AOR = 0.25, 95% CI: 0.08-0.81), being a refugee or visa holder (AOR = 0.18, 95% CI: 0.05-0.65), and living outside Vancouver (AOR = 0.52, 95% CI: 0.33-0.82), and positively associated with abnormal anxiety symptomology scores (AOR = 3.05, 95% CI: 2.06-4.51). Mental health conditions and substance use, which have important implications for clinical and public health practice, were highly prevalent and co-occurring.

Southwestern Washington 6 arc-second DEM

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The 6-second Southwest Washington Elevation Grid provides bathymetric data in ASCII raster format of 6-second resolution in geographic coordinates. This grid is...

The preliminary results: Internal seismic velocity structure imaging beneath Mount Lokon

Energy Technology Data Exchange (ETDEWEB)

Firmansyah, Rizky, E-mail: rizkyfirmansyah@hotmail.com [Geophysical Engineering, Faculty of Mining and Petroleum Engineering, Institut Teknologi Bandung, Bandung, 40132 (Indonesia); Nugraha, Andri Dian, E-mail: nugraha@gf.itb.ac.id [Global Geophysical Group, Faculty of Mining and Petroleum Engineering, Institut Teknologi Bandung, Bandung, 40132 (Indonesia); Kristianto, E-mail: kris@vsi.esdm.go.id [Center for Volcanology and Geological Hazard Mitigation (CVGHM), Geological Agency, Bandung, 40122 (Indonesia)

2015-04-24

Historical records that before the 17{sup th} century, Mount Lokon had been dormant for approximately 400 years. In the years between 1350 and 1400, eruption ever recorded in Empung, came from Mount Lokon’s central crater. Subsequently, in 1750 to 1800, Mount Lokon continued to erupt again and caused soil damage and fall victim. After 1949, Mount Lokon dramatically increased in its frequency: the eruption interval varies between 1 – 5 years, with an average interval of 3 years and a rest interval ranged from 8 – 64 years. Then, on June 26{sup th}, 2011, standby alert set by the Center for Volcanology and Geological Hazard Mitigation. Peak activity happened on July 4{sup th}, 2011 that Mount Lokon erupted continuously until August 28{sup th}, 2011. In this study, we carefully analyzed micro-earthquakes waveform and determined hypocenter location of those events. We then conducted travel time seismic tomographic inversion using SIMULPS12 method to detemine Vp, Vs and Vp/Vs ratio structures beneath Lokon volcano in order to enhance our subsurface geological structure. During the tomographic inversion, we started from 1-D seismic velocities model obtained from VELEST33 method. Our preliminary results show low Vp, low Vs, and high Vp/Vs are observed beneath Mount Lokon-Empung which are may be associated with weak zone or hot material zones. However, in this study we used few station for recording of micro-earthquake events. So, we suggest in the future tomography study, the adding of some seismometers in order to improve ray coverage in the region is profoundly justified.

77 FR 37317 - Drawbridge Operation Regulation; Lake Washington, Seattle, WA

Science.gov (United States)

2012-06-21

..., 2012. The deviation allows the floating draw span of the SR 520 Lake Washington Bridge to remain in the... schedule that governs the State Route 520 (SR 520) Bridge across Lake Washington at Seattle, WA. This... allows the bridge to remain in the closed position to allow safe movement of event participants. DATES...

Design of a new engine mount for vertical and horizontal vibration control using magnetorheological fluid

International Nuclear Information System (INIS)

Phu, D X; Choi, S B; Lee, Y S; Han, M S

2014-01-01

This paper presents a new design of a magnetorheological fluid (MR) mount for vibration control considering both vertical forces and horizontal moments such as are met in various engine systems, including a medium high-speed engine of ship. The newly designed mount, called a MR brake mount, offers several salient benefits such as small size and relatively high load capacity compared with a conventional MR engine mount that can control vertical vibration only. The principal design parameters of the proposed mount are optimally determined to achieve maximum torque with geometric and spatial constraints. Subsequently, the proposed MR mount is designed and manufactured based on the optimized design parameters. It is shown from experimental testing that the proposed mount, which combines MR mount with MR brake, can produce the desired force and torque to reduce unwanted vibration of a medium high-speed engine system of ship subjected to both vertical and horizontal exciting motions. In addition, it is verified that there is no large difference between experiment results and simulation results that are obtained from an analytical model derived in this work. (technical note)

Timber resource statistics for southwest Washington.

Science.gov (United States)

Patricia M. Bassett; Daniel D. Oswald

1981-01-01

This report summarizes a 1978 timber-resource inventory of six counties in southwest Washington: Clark, Cowlitz, Lewis, Pacific, Skamania, and Wahkiakum. Detailed tables of forest area, timber volume, growth, mortality, and harvest are presented.

Uncertainty of power curve measurement with a two-beam nacelle-mounted lidar

DEFF Research Database (Denmark)

Wagner, Rozenn; Courtney, Michael Stephen; Friis Pedersen, Troels

2015-01-01

Nacelle lidars are attractive for offshore measurements since they can provide measurements of the free wind speed in front of the turbine rotor without erecting a met mast, which significantly reduces the cost of the measurements. Nacelle-mounted pulsed lidars with two lines of sight (LOS) have...... lies between 1 and 2% for the wind speed range between cut-in and rated wind speed. Finally, the lidar was mounted on the nacelle of a wind turbine in order to perform a power curve measurement. The wind speed was simultaneously measured with a mast-top mounted cup anemometer placed two rotor diameters...... lidar was less than 10% larger on average than that obtained with the mast mounted cup anemometer. Copyright © 2015 John Wiley & Sons, Ltd....

Characterization of Multilayer Piezoelectric Actuators for Use in Active Isolation Mounts

Science.gov (United States)

Wise, Stephanie A.; Hooker, Matthew W.

1997-01-01

Active mounts are desirable for isolating spacecraft science instruments from on-board vibrational sources such as motors and release mechanisms. Such active isolation mounts typically employ multilayer piezoelectric actuators to cancel these vibrational disturbances. The actuators selected for spacecraft systems must consume minimal power while exhibiting displacements of 5 to 10 micron under load. This report describes a study that compares the power consumption, displacement, and load characteristics of four commercially available multilayer piezoelectric actuators. The results of this study indicate that commercially available actuators exist that meet or exceed the design requirements used in spacecraft isolation mounts.

City of North Vancouver greenhouse gas local action plan : final report

International Nuclear Information System (INIS)

Hood, I.

2005-02-01

This paper presented details of a greenhouse gas (GHG) local action plan developed as a result of the City of North Vancouver's participation in the Partners for Climate Protection Program (PCPP). The plan is intended to better manage the impacts of urban development related to GHG and air quality, while also achieving community objectives related to affordable housing, transportation management, job creation and economic development. The report reviewed the local emissions inventory in addition to various programs, plans, policies and by-laws relating to energy management. Potential policies and programs were identified to achieve GHG emissions reductions in accordance with the PCPP. A plan for emissions reductions was also presented. A situation analysis was presented with details of population, transportation, residential and commercial building and industry. Solid waste management and transportation plans were outlined. A GHG emissions profile and forecast was presented. An outline of a GHG management framework included information on initiatives in the city as well as details of public consultation feedback. A program implementation plan includes forecasts of the program's impact, as well as details of program delivery and a performance measurement framework. Proposed initiatives in the plan included new building guidelines; fuel switching for light and heavy duty vehicles; driver training and enhanced vehicle maintenance programs; and, an environmental procurement policy. Community programs include residential and commercial building retrofits; land use planning; support for community energy systems; green building design guidelines; transportation demand management; and, public engagement and outreach programs. 21 tabs., 9 figs

Preparation and mounting of adult Drosophila structures in Canada balsam.

Science.gov (United States)

Stern, David L; Sucena, Elio

2012-03-01

The Drosophila cuticle carries a rich array of morphological details. Thus, cuticle examination has had a central role in the history of genetics. To prepare fine "museum-quality," permanent slides, it is best to mount specimens in Canada Balsam. It is difficult to give precise recipes for Canada Balsam, because every user seems to prefer a slightly different viscosity. Dilute solutions spread easily and do not dry too rapidly while mounting specimens. The disadvantage is that there is actually less Balsam in a "drop" of the solution, and when dried, it can contract from the sides of the coverslip, sometimes disturbing the specimen. Unfortunately, there is no substitute for experience when using Canada Balsam. This protocol describes a procedure for mounting adult cuticles in Canada Balsam.

Mounting Systems for Structural Members, Fastening Assemblies Thereof, and Vibration Isolation Systems Including the Same

Science.gov (United States)

Young, Ken (Inventor); Hindle, Timothy (Inventor); Barber, Tim Daniel (Inventor)

2016-01-01

Mounting systems for structural members, fastening assemblies thereof, and vibration isolation systems including the same are provided. Mounting systems comprise a pair of mounting brackets, each clamped against a fastening assembly forming a mounting assembly. Fastening assemblies comprise a spherical rod end comprising a spherical member having a through opening and an integrally threaded shaft, first and second seating members on opposite sides of the spherical member and each having a through opening that is substantially coaxial with the spherical member through opening, and a partially threaded fastener that threadably engages each mounting bracket forming the mounting assembly. Structural members have axial end portions, each releasably coupled to a mounting bracket by the integrally threaded shaft. Axial end portions are threaded in opposite directions for permitting structural member rotation to adjust a length thereof to a substantially zero strain position. Structural members may be vibration isolator struts in vibration isolation systems.

Scintillation crystal mounting apparatus

International Nuclear Information System (INIS)

Engdahl, L.W.; Deans, A.J.

1982-01-01

An improved detector head for a gamma camera is disclosed. The detector head includes a housing and a detector assembly mounted within the housing. Components of the detector assembly include a crystal sub-assembly, a phototube array, and a light pipe between the phototube array and crystal sub-assembly. The invention provides a unique structure for maintaining the phototubes in optical relationship with the light pipe and preventing the application of forces that would cause the camera's crystal to crack

Preliminary Mineralogic and Stable Isotope Studies of Altered Summit and Flank Rocks and Osceola Mudflow Deposits on Mount Rainier, Washington

Science.gov (United States)

Rye, Robert O.; Breit, George N.; Zimbelman, David R.

2003-01-01

About 5600 years ago part of Mount Rainier?s edifice collapsed with the resultant Osceola Mudflow traveling more than 120 km and covering an area of at least 505 km2. Mineralogic and stable isotope studies were conducted on altered rocks from outcrops near the summit and east flank of the volcano and samples of clasts and matrix from the Osceola Mudflow. Results of these analyses are used to constrain processes responsible for pre-collapse alteration and provide insight into the role of alteration in edifice instability prior to the Osceola collapse event. Jarosite, pyrite, alunite, and kaolinite occur in hydrothermally altered rock exposed in summit scarps formed by edifice collapse events and in altered rock within the east-west structural zone (EWSZ) of the volcano?s east flank. Deposits of the Osceola Mudflow contain clasts of variably altered and unaltered andesite within a clay-rich matrix. Minerals detected in samples from the edifice are also present in many of the clasts. The matrix includes abundant smectite, kaolinite and variably abundant jarosite. Hydrothermal fluid compositions calculated from hydrogen and oxygen isotope data of alunite, and smectite on Mount Rainier reflect mixing of magmatic and meteoric waters. The range in the dD values of modern meteoric water on the volcano (-85 to 155?) reflect the influence of elevation on the dD of precipitation. The d34S and d18OSO4 values of alunite, gypsum and jarosite are distinct but together range from 1.7 to 17.6? and -12.3 to 15.0?, respectively; both parameters increase from jarosite to gypsum to alunite. The variations in sulfur isotope composition are attributed to the varying contributions of disproportionation of magmatic SO2, the supergene oxidation of hydrothermal pyrite and possible oxidation of H2S to the parent aqueous sulfate. The 18OSO4 values of jarosite are the lowest recorded for the mineral, consistent with a supergene origin. The mineralogy and isotope composition of alteration

To Be a Slave: The Boyhood of Booker T. Washington.

Science.gov (United States)

National Park Service (Dept. of Interior), Washington, DC.

The Booker T. Washington National Monument preserves and protects the birth site and childhood home of Booker T. Washington, while interpreting his life experiences and significance in U.S. history as the most powerful African American between 1895 and 1915. The park provides a resource for public education and a focal point for continuing…

Apparatus and method for mounting photovoltaic power generating systems on buildings

Science.gov (United States)

Russell, Miles Clayton [Lincoln, MA

2008-10-14

Rectangular PV modules (6) are mounted on a building roof (4) by mounting stands that are distributed in rows and columns. Each stand comprises a base plate (10) that rests on the building roof (4) and first and second brackets (12, 14) of different height attached to opposite ends of the base plate (10). Each bracket (12, 14) has dual members for supporting two different PV modules (6), and each PV module (6) has a mounting pin (84) adjacent to each of its four corners. Each module (6) is supported by attachment of two of its mounting pins (84) to different first brackets (12), whereby the modules (6) and their supporting stands are able to resist uplift forces resulting from high velocity winds without the base plates (10) being physically attached to the supporting roof structure (4). Preferably the second brackets (14) have a telescoping construction that permits their effective height to vary from less than to substantially the same as that of the first brackets (12).

Timber resource statistics for eastern Washington.

Science.gov (United States)

Patricia M. Bassett; Daniel D. Oswald

1983-01-01

This report summarizes a 1980 timber resource inventory of the 16 forested counties in Washington east of the crest of the Cascade Range. Detailed tables of forest area, timber volume, growth, mortality, and harvest are presented.

Adjustable bipod flexures for mounting mirrors in a space telescope.

Science.gov (United States)

Kihm, Hagyong; Yang, Ho-Soon; Moon, Il Kweon; Yeon, Jeong-Heum; Lee, Seung-Hoon; Lee, Yun-Woo

2012-11-10

A new mirror mounting technique applicable to the primary mirror in a space telescope is presented. This mounting technique replaces conventional bipod flexures with flexures having mechanical shims so that adjustments can be made to counter the effects of gravitational distortion of the mirror surface while being tested in the horizontal position. Astigmatic aberration due to the gravitational changes is effectively reduced by adjusting the shim thickness, and the relation between the astigmatism and the shim thickness is investigated. We tested the mirror interferometrically at the center of curvature using a null lens. Then we repeated the test after rotating the mirror about its optical axis by 180° in the horizontal setup, and searched for the minimum system error. With the proposed flexure mount, the gravitational stress at the adhesive coupling between the mirror and the mount is reduced by half that of a conventional bipod flexure for better mechanical safety under launch loads. Analytical results using finite element methods are compared with experimental results from the optical interferometer. Vibration tests verified the mechanical safety and optical stability, and qualified their use in space applications.

Real-time electrocardiogram transmission from Mount Everest during continued ascent.

Directory of Open Access Journals (Sweden)

Wei-Fong Kao

Full Text Available The feasibility of a real-time electrocardiogram (ECG transmission via satellite phone from Mount Everest to determine a climber's suitability for continued ascent was examined. Four Taiwanese climbers were enrolled in the 2009 Mount Everest summit program. Physiological measurements were taken at base camp (5300 m, camp 2 (6400 m, camp 3 (7100 m, and camp 4 (7950 m 1 hour after arrival and following a 10 minute rest period. A total of 3 out of 4 climbers were able to summit Mount Everest successfully. Overall, ECG and global positioning system (GPS coordinates of climbers were transmitted in real-time via satellite phone successfully from base camp, camp 2, camp 3, and camp 4. At each camp, Resting Heart Rate (RHR was transmitted and recorded: base camp (54-113 bpm, camp 2 (94-130 bpm, camp 3 (98-115 bpm, and camp 4 (93-111 bpm. Real-time ECG and GPS coordinate transmission via satellite phone is feasible for climbers on Mount Everest. Real-time RHR data can be used to evaluate a climber's physiological capacity to continue an ascent and to summit.

40 CFR 81.348 - Washington.

Science.gov (United States)

2010-07-01

... 5/14/01 Attainment The City of Kent and a portion of the Green River valley bounded on the east and... Type Seattle-Tacoma Area: Seattle-Tacoma Urban Area (as defined by the Washington Department of Transportation urban area maps) King County (part) Attainment Pierce County (part) Attainment Snohomish County...

Motion planning for gantry mounted manipulators

DEFF Research Database (Denmark)

Olsen, Anders Lau; Petersen, Henrik Gordon

2007-01-01

We present a roadmap based planner for finding robot motions for gantry mounted manipulators for a line welding application at Odense Steel Shipyard (OSS). The robot motions are planned subject to constraints on when the gantry may be moved. We show that random sampling of gantry configurations...

Mounting LHCb hadron calorimeter scintillating tiles

CERN Multimedia

Maximilien Brice

2004-01-01

Scintillating tiles are carefully mounted in the hadronic calorimeter for the LHCb detector. These calorimeters measure the energy of particles that interact via the strong force, called hadrons. The detectors are made in a sandwich-like structure where these scintillator tiles are placed between metal sheets.

A structural comparison of female-male and female-female mounting in Japanese macaques (Macaca fuscata).

Science.gov (United States)

Ottenheimer Carrier, Lydia; Leca, Jean-Baptiste; Pellis, Sergio; Vasey, Paul L

2015-10-01

In certain populations, female Japanese macaques (Macaca fuscata) mount both males and females. Vasey (2007) proposed that female-female sexual mounting in Japanese macaques may be a neutral evolutionary by-product of a purported adaptation, namely, female-male mounting. In this study, we aim to further examine the proposed link between female-male and female-female mounting in Japanese macaques by comparing the structural characteristics that define both forms of mounting. We do so using Eshkol-Wachman Movement Notation (EWMN), a globographic reference system that can be used to describe the position of body segments. No significant differences were observed in the female mounters' positioning of eight different body segments (i.e., lower torso, mid-torso, upper torso, upper arm, lower arm, upper leg, lower leg, and foot) during female-male and female-female mounting. This finding lends support to the conclusion that female-female and female-male mounting are structurally, and thus, evolutionarily, related. Copyright © 2015 Elsevier B.V. All rights reserved.

Vibration control of a camera mount system for an unmanned aerial vehicle using piezostack actuators

International Nuclear Information System (INIS)

Oh, Jong-Seok; Choi, Seung-Bok; Han, Young-Min

2011-01-01

This work proposes an active mount for the camera systems of unmanned aerial vehicles (UAV) in order to control unwanted vibrations. An active actuator of the proposed mount is devised as an inertial type, in which a piezostack actuator is directly connected to the inertial mass. After evaluating the actuating force of the actuator, it is combined with the rubber element of the mount, whose natural frequency is determined based on the measured vibration characteristics of UAV. Based on the governing equations of motion of the active camera mount, a robust sliding mode controller (SMC) is then formulated with consideration of parameter uncertainties and hysteresis behavior of the actuator. Subsequently, vibration control performances of the proposed active mount are experimentally evaluated in the time and frequency domains. In addition, a full camera mount system of UAVs that is supported by four active mounts is considered and its vibration control performance is evaluated in the frequency domain using a hardware-in-the-loop simulation (HILS) method

Geothermal energy in Washington: site data base and development status

Energy Technology Data Exchange (ETDEWEB)

Bloomquist, R.G.

1979-04-01

This is an attempt to identify the factors which have affected and will continue to affect geothermal assessment and development in the state. The eight potential sites chosen for detailed analysis include: Indian Heaven KGRA, Mount St. Helens KGRA, Kennedy Hot Springs KGRA, Mount Adams PGRA (Potential Geothermal Resource Area), Mount Rainier PGRA, Mount Baker PGRA, Olympic-Sol Duc Hot Springs, and Yakima. The following information is included for each site: site data, site location and physical description, geological/geophysical description, reservoir characteristics, land ownership and leasing, geothermal development status, institutional characteristics, environmental factors, transportation and utilities, and population. A number of serious impediments to geothermal development were identified which can be solved only by legislative action at the state or federal level and/or changes in attitudes by regulatory agencies. (MHR)

Arterial blood gases and oxygen content in climbers on Mount Everest

NARCIS (Netherlands)

Grocott, Michael P. W.; Martin, Daniel S.; Levett, Denny Z. H.; McMorrow, Roger; Windsor, Jeremy; Montgomery, Hugh E.; Ahuja, V.; Aref-Adib, G.; Burnham, R.; Chisholm, A.; Clarke, K.; Coates, D.; Coates, M.; Cook, D.; Cox, M.; Dhillon, S.; Dougall, C.; Doyle, P.; Duncan, P.; Edsell, M.; Edwards, L.; Evans, L.; Gardiner, P.; Grocott, M.; Gunning, P.; Hart, N.; Harrington, J.; Harvey, J.; Holloway, C.; Howard, D.; Hurlbut, D.; Imray, C.; Ince, C.; Jonas, M.; van der Kaaij, J.; Khosravi, M.; Kolfschoten, N.; Levett, D.; Luery, H.; Luks, A.; Martin, D.; McMorrow, R.; Meale, P.; Mitchell, K.; Montgomery, H.; Morgan, G.; Morgan, J.; Murray, A.; Mythen, M.; Newman, S.

2009-01-01

BACKGROUND: The level of environmental hypobaric hypoxia that affects climbers at the summit of Mount Everest (8848 m [29,029 ft]) is close to the limit of tolerance by humans. We performed direct field measurements of arterial blood gases in climbers breathing ambient air on Mount Everest. METHODS:

Mounting ground sections of teeth: Cyanoacrylate adhesive versus Canada balsam.

Science.gov (United States)

Vangala, Manogna Rl; Rudraraju, Amrutha; Subramanyam, R V

2016-01-01

Hard tissues can be studied by either decalcification or by preparing ground sections. Various mounting media have been tried and used for ground sections of teeth. However, there are very few studies on the use of cyanoacrylate adhesive as a mounting medium. The aim of our study was to evaluate the efficacy of cyanoacrylate adhesive (Fevikwik™) as a mounting medium for ground sections of teeth and to compare these ground sections with those mounted with Canada balsam. Ground sections were prepared from twenty extracted teeth. Each section was divided into two halves and mounted on one slide, one with cyanoacrylate adhesive (Fevikwik™) and the other with Canada balsam. Scoring for various features in the ground sections was done by two independent observers. Statistical analysis using Student's t-test (unpaired) of average scores was performed for each feature observed. No statistically significant difference was found between the two for most of the features. However, cyanoacrylate was found to be better than Canada balsam for observing striae of Retzius (P < 0.0205), enamel lamellae (P < 0.036), dentinal tubules (P < 0.0057), interglobular dentin (P < 0.0001), sclerotic dentin - transmitted light (P < 0.00001), sclerotic dentin - polarized light (P < 0.0002) and Sharpey's fibers (P < 0.0004). This initial study shows that cyanoacrylate is better than Canada balsam for observing certain features of ground sections of teeth. However, it remains to be seen whether it will be useful for studying undecalcified sections of carious teeth and for soft tissue sections.

Refining aging criteria for northern sea otters in Washington State

Science.gov (United States)

Schuler, Krysten L.; Baker, Bridget B.; Mayer, Karl A.; Perez-Heydrich, Carolina; Holahan, Paula M.; Thomas, Nancy J.; White, C. LeAnn

2018-01-01

Measurement of skull ossification patterns is a standard method for aging various mammalian species and has been used to age Russian, Californian, and Alaskan sea otter populations. Cementum annuli counts have also been verified as an accurate aging method for the Alaskan sea otter population. In this study, cementum annuli count results and skull ossification patterns were compared as methods for aging the northern sea otter (Enhydra lutris kenyoni) population in Washington State. Significant agreement was found between the two methods suggesting that either method could be used to age the Washington population of otters. This study also found that ossification of the squamosal-jugal suture at the ventral glenoid fossa can be used to differentiate male subadults from adults. To assist field biologists or others without access to cementum annuli or skull ossification analysis techniques, a suite of morphologic, physiologic, and developmental characteristics were analyzed to assess whether a set of these more easily accessible parameters could also predict age class for the Washington population of otters. Tooth condition score, evidence of reproductive activity in females, and tooth eruption pattern were identified as the most useful criteria for classifying Washington sea otters as pups, juveniles, subadults, or adults/aged adults. A simple decision tree based on characteristics accessible in the field or at necropsy was created that can be used to reliably predict age class of Washington sea otters as determined by cementum annuli.

76 FR 18001 - Irish Potatoes Grown in Washington; Decreased Assessment Rate

Science.gov (United States)

2011-04-01

... IR] Irish Potatoes Grown in Washington; Decreased Assessment Rate AGENCY: Agricultural Marketing... rate established for the State of Washington Potato Committee (Committee) for the 2011-2012 and subsequent fiscal periods from $0.0035 to $0.003 per hundredweight of potatoes handled. The Committee locally...

76 FR 41589 - Irish Potatoes Grown in Washington; Decreased Assessment Rate

Science.gov (United States)

2011-07-15

... FIR] Irish Potatoes Grown in Washington; Decreased Assessment Rate AGENCY: Agricultural Marketing... established for the State of Washington Potato Committee (Committee) for the 2011-2012 and subsequent fiscal periods from $0.0035 to $0.003 per hundredweight of potatoes handled. The Committee locally administers...

A Partnership for Modeling the Marine Environment of Puget Sound, Washington

Science.gov (United States)

2009-03-30

Northwest National Marine Renewable Energy Center, a joint University of Washington - Oregon State project funded by the U.S. Department of Energy. e. A... Marine Renewable Energy Center (NNMREC), a joint Washington - Oregon State project to investigate extraction of wave and tidal energy sponsored by

Booker T. Washington's Educational Contributions to Contemporary Practices of Sustainable Development

Science.gov (United States)

Grant, Brett G.

2014-01-01

This article discusses Booker T. Washington's educational contributions to contemporary practices of sustainable development. In particular, the article looks at Washington's contributions in the areas of economic sustainability and entrepreneurship, character development, and aesthetics. As states continue to contemplate and evaluate the value of…

CFRP platform and hexapod mount for the Array of MIcrowave Background Anisotropy (AMiBA)

Science.gov (United States)

Raffin, Philippe A.; Martin, Robert N.; Huang, Yau-De; Patt, Ferdinand; Romeo, Robert C.; Chen, Ming-Tang; Kingsley, Jeffrey S.

2004-09-01

AMiBA consists of a 90 GHz interferometric array telescope with dishes ranging in size from 0.3 to 2.4 meter in diameter, mounted on a 6-meter fully steerable platform. The dishes are attached to the receivers, which are mounted on a platform controlled by a six degree of freedom hexapod mount. The hexapod mount is a parallel connection manipulator also called Stewart Platform. The basic reference for this mechanism is a paper by Stewart. The Stewart Platform is a unique kinematically constrained work platform. It can be manipulated through the six degrees of freedom. The hexapod also provides better accuracy, rigidity, load to weight ratio and load distribution than a serial manipulator or traditional manipulator. The advantages of the hexapod shows that it is a great choice for the AMiBA project. Vertex Antennentechnik GmbH fabricates the hexapod. Testing has started in Germany. The telescope will be delivered in the summer of 2004. The 6m in diameter hexagonal platform is made of carbon fiber reinforced plastics (CFRP) and consists of seven pieces of three different unique types. The platform can be disassembled and fits in a container for transportation. The mounting plane flatness is an important issue for the platform assembly. The deflection angle of the mounting plane relative to any other mounting position must be less than 20 arcsec. Meanwhile, the platform must endure a loading of 3 tons. The platform has been built by Composite Mirror Applications, Inc. (CMA) in Tucson, and mounted on the Hexapod in Germany. This report describes the design and testing of platform and mount for the AMiBA telescope.

An annotated checklist of the vascular flora of Washington County Mississippi

Science.gov (United States)

Field explorations have yielded 257 species new to Washington County, Mississippi and Calandrinia ciliata (Ruiz & Pav.) DC. and Ruellia nudiflora (Engelm. & Gray) Urban new to the state. An annotated list of 796 taxa for Washington County is provided and excludes 62 species that were reported from ...

Washington: a guide to geothermal energy development

Energy Technology Data Exchange (ETDEWEB)

Bloomquist, R.G.; Basescu, N.; Higbee, C.; Justus, D.; Simpson, S.

1980-06-01

Washington's geothermal potential is discussed. The following topics are covered: exploration, drilling, utilization, legal and institutional setting, and economic factors of direct use projects. (MHR)

Field-trip guide to Mount Hood, Oregon, highlighting eruptive history and hazards

Science.gov (United States)

Scott, William E.; Gardner, Cynthia A.

2017-06-22

This guidebook describes stops of interest for a geological field trip around Mount Hood volcano. It was developed for the 2017 International Association of Volcanology and Chemistry of the Earth’s Interior (IAVCEI) Scientific Assembly in Portland, Oregon. The intent of this guidebook and accompanying contributions is to provide an overview of Mount Hood, including its chief geologic processes, magmatic system, eruptive history, local tectonics, and hazards, by visiting a variety of readily accessible localities. We also describe coeval, largely monogenetic, volcanoes in the region. Accompanying the field-trip guidebook are separately authored contributions that discuss in detail the Mount Hood magmatic system and its products and behavior (Kent and Koleszar, this volume); Mount Hood earthquakes and their relation to regional tectonics and the volcanic system (Thelen and Moran, this volume); and young surface faults cutting the broader Mount Hood area whose extent has come to light after acquisition of regional light detection and ranging coverage (Madin and others, this volume).The trip makes an approximately 175-mile (280-kilometer) clockwise loop around Mount Hood, starting and ending in Portland. The route heads east on Interstate 84 through the Columbia River Gorge National Scenic Area. The guidebook points out only a few conspicuous features of note in the gorge, but many other guides to the gorge are available. The route continues south on the Mount Hood National Scenic Byway on Oregon Route 35 following Hood River, and returns to Portland on U.S. Highway 26 following Sandy River. The route traverses rocks as old as the early Miocene Eagle Creek Formation and overlying Columbia River Basalt Group of middle Miocene age, but chiefly lava flows and clastic products of arc volcanism of late Miocene to Holocene age.

Using Priors to Compensate Geometrical Problems in Head-Mounted Eye Trackers

DEFF Research Database (Denmark)

Batista Narcizo, Fabricio; Ahmed, Zaheer; Hansen, Dan Witzner

The use of additional information (a.k.a. priors) to help the eye tracking process is presented as an alternative to compensate classical geometrical problems in head-mounted eye trackers. Priors can be obtained from several distinct sources, such as: sensors to collect information related...... estimation specially for uncalibrated head-mounted setups....

An improved mounting device for attaching intracranial probes in large animal models.

Science.gov (United States)

Dunster, Kimble R

2015-12-01

The rigid support of intracranial probes can be difficult when using animal models, as mounting devices suitable for the probes are either not available, or designed for human use and not suitable in animal skulls. A cheap and reliable mounting device for securing intracranial probes in large animal models is described. Using commonly available clinical consumables, a universal mounting device for securing intracranial probes to the skull of large animals was developed and tested. A simply made mounting device to hold a variety of probes from 500 μm to 1.3 mm in diameter to the skull was developed. The device was used to hold probes to the skulls of sheep for up to 18 h. No adhesives or cements were used. The described device provides a reliable method of securing probes to the skull of animals.

Squaring Up: Experiences of Transition from Off-Street Sex Work to Square Work and Duality--Concurrent Involvement in Both--in Vancouver, BC.

Science.gov (United States)

Bowen, Raven R

2015-11-01

Many studies of exit from sex work are inspired by role theory, where people experience a lack of attachment to a role; are faced with individual, interactional, and structural challenges; contemplate transition and exit a role; and then struggle to establish postrole identities and new lives. This framework has been used to explicate the factors and experiences of those who leave or attempt to leave the sex industry; however, it is limited because studies present sex work as a harmful and dangerous profession that people are trapped in, escaping, or have survived. In this paper, I discuss Vancouver's history of violence against sex workers and I review research on sex work exiting and bring forward recommendations for the design of exit program based on the experiences of 22 active and former off-street sex workers from Vancouver, British Columbia. I describe study participants who include Sex-Work-No-More participants who would not return to the industry, Sex-Work-Maybe participants who consider reinvolvement, and Dual-Life participants who are employed in sex work and conventional work simultaneously. These participants uniquely challenge narrow, binary understandings of involvement and transition because they discuss their use of deception to obtain resources needed to make change; the support that clients have provided; their strategic engagement in sex work as a means to exit; their considerations of reentry; and for some, their dual employment. In light of new legislation that criminalizes activities related to sex work-the Protection of Communities and Exploited Persons Act-and the Federal government announcement of $20 million dollars for the creation of exit services nationwide, hearing from sex workers is essential to advancing agendas in this area. © 2015 Canadian Sociological Association/La Société canadienne de sociologie.

A new magnetorheological mount featured by changeable damping gaps using a moved-plate valve structure

International Nuclear Information System (INIS)

Phu, Do Xuan; Shah, Kruti; Choi, Seung-Bok

2014-01-01

In this work, a new type of a magnetorheological (MR) fluid mount is proposed and its performances are experimentally investigated. The design of this MR mount is based on two operating modes of MR fluid: flow mode and shear mode. These modes are applied to the mechanism design consisting of two components: a fixed plate for applying the flow mode, and a moved plate for applying the shear mode of MR fluid motion. These plates belong to the valve-type structure of MR mount. The primary objective using the moved plate is to overcome the block-up phenomenon which frequently occurs in the conventional-type MR mount, in which there is no flow of MR fluid through the damping gap. In this research, a laboratorial fluid (MRF140) is used in the design and optimization of MR mount. This fluid features plate-like particles unlike the sphere particles. The yield stress of the fluid is measured as a function of the magnetic field and the theoretical analysis for the mount design is undertaken using the properties of the MR fluid, followed by design optimization. The objective function is concentrated on maximal damping force of the MR mount subjected to parameter constraints. Based on the results of optimization, the proposed MR mount is manufactured and tested for the performance evaluation. Vibration control capability and block-up phenomenon are investigated and compared between the proposed and conventional MR mounts. (paper)

78 FR 48285 - Irish Potatoes Grown in Washington; Decreased Assessment Rate

Science.gov (United States)

2013-08-08

...; FV13-946-1 FIR] Irish Potatoes Grown in Washington; Decreased Assessment Rate AGENCY: Agricultural... established for the State of Washington Potato Committee (Committee) for the 2013-2014 fiscal year and all subsequent fiscal periods from $0.003 to $0.0025 per hundredweight of potatoes handled. The Committee locally...

Advanced astigmatism-corrected tandem Wadsworth mounting for small-scale spectral broadband imaging spectrometer.

Science.gov (United States)

Lei, Yu; Lin, Guan-yu

2013-01-01

Tandem gratings of double-dispersion mount make it possible to design an imaging spectrometer for the weak light observation with high spatial resolution, high spectral resolution, and high optical transmission efficiency. The traditional tandem Wadsworth mounting is originally designed to match the coaxial telescope and large-scale imaging spectrometer. When it is used to connect the off-axis telescope such as off-axis parabolic mirror, it presents lower imaging quality than to connect the coaxial telescope. It may also introduce interference among the detector and the optical elements as it is applied to the short focal length and small-scale spectrometer in a close volume by satellite. An advanced tandem Wadsworth mounting has been investigated to deal with the situation. The Wadsworth astigmatism-corrected mounting condition for which is expressed as the distance between the second concave grating and the imaging plane is calculated. Then the optimum arrangement for the first plane grating and the second concave grating, which make the anterior Wadsworth condition fulfilling each wavelength, is analyzed by the geometric and first order differential calculation. These two arrangements comprise the advanced Wadsworth mounting condition. The spectral resolution has also been calculated by these conditions. An example designed by the optimum theory proves that the advanced tandem Wadsworth mounting performs excellently in spectral broadband.

The impact of the Vancouver Island natural gas pipeline construction on water quality

International Nuclear Information System (INIS)

Li Gaoshe.

1993-04-01

A study was initiated to evaluate the impact of construction of the Vancouver Island natural gas pipeline on water quality, where the pipeline passed along or through lakes and streams. The main concern was for the potential defilement of community water supplies when construction occurred in community watersheds. When water becomes turbid from rainfall runoff passing through construction areas, disinfection processes are rendered inefficacious and at specified turbidity levels, the water becomes too risky to drink without alternative disinfection such as boiling. The weekly environmental surveillance reports generated during construction are reviewed. The material is organized to relate construction practices with weather patterns, thereby showing the resultant effects on water quality (turbidity). The effectiveness of construction measures in reducing the risk of contamination and water turbidity at intakes is assessed. Generally, water turbidity during project construction was acceptable although it sometimes reached very high levels. These high levels resulted from incidents or mistakes that were usually related to rainy days. Among the 12 types of work activity, bridge construction, drilling, and grading caused relatively slight increases in water turbidity levels, while backfilling and ditching caused the greatest increase in turbidity. Improvements in inspection and monitoring programs are recommended. A key recommendation is that construction work be stopped on rainy days. 6 refs., 4 figs., 20 tabs

The alignment and isostatic mount bonding technique of the aerospace Cassegrain telescope primary mirror

Science.gov (United States)

Lin, Wei Cheng; Chang, Shenq-Tsong; Lin, Yu-Chuan; Hsu, Ming-Ying; Chang, Yu-Ting; Chang, Sheng-Hsiung; Huang, Ting-Ming

2012-10-01

In order to meet both optical performance and structural stiffness requirements of the aerospace Cassegrain telescope, iso-static mount is used as the interface between the primary mirror and the main plate. This article describes the alignment and iso-static mount bonding technique of the primary mirror by assistance of CMM. The design and assembly of mechanical ground support equipment (MGSE) which reduces the deformation of primary mirror by the gravity effect is also presented. The primary mirror adjusting MGSE consists of X-Y linear translation stages, rotation stage and kinematic constrain platform which provides the function of decenter, orientation, tilt and height adjustment of the posture sequentially. After CMM measurement, the radius of curvature, conic constant, decenter and tilt, etc. will be calculated. According to these results, the posture of the mirror will be adjusted to reduce the tilt by the designed MGSE within 0.02 degrees and the distance deviation from the best fitted profile of mirror to main plate shall be less than 0.01 mm. After that, EC 2216 adhesive is used to bond mirror and iso-static mount. During iso-static mount bonding process, CMM is selected to monitor the relative position deviation of the iso-static mount until the adhesive completely cured. After that, the wave front sensors and strain gauges are used to monitor the strain variation while the iso-static mount mounted in the main plate with the screws by the torque wrench. This step is to prevent deformation of the mirror caused from force of the iso-static mount during the mounting process. In the end, the interferometer is used for the optical performance test with +1G and -1G to check the alignment and bonding technique is well or not.

Self-tuning disturbance feedforward control with drift prevention for air mount systems

NARCIS (Netherlands)

Beijen, M.A.; Heertjes, M.F.; Butler, H.

2015-01-01

A MIMO disturbance feedforward control strategy is presented to isolate an industrial active vibration isolation system with air mounts from broadband floor vibrations. The feedforward controller compensates for the static damping and stiffness of the air mount suspension, leading to significant

Marijuana, other drugs, and alcohol use by drivers in Washington state : appendices.

Science.gov (United States)

2016-07-01

In Washington State legal sales of marijuana began July 8, 2014. A voluntary, anonymous roadside study was conducted to assess the prevalence of drivers testing positive for alcohol and other drugs, including marijuana, on Washingtons roads. Data ...

75 FR 14463 - Notice of Inventory Completion: University of Washington, Department of Anthropology, Seattle, WA

Science.gov (United States)

2010-03-25

... Washington, Department of Anthropology, Seattle, WA AGENCY: National Park Service, Interior. ACTION: Notice... University of Washington, Department of Anthropology, Seattle, WA. The human remains were removed from... University of Washington, Department of Anthropology and Burke Museum staff in consultation with...

76 FR 58033 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2011-09-19

... DEPARTMENT OF THE INTERIOR National Park Service [2253-665] Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of Washington, Seattle, WA AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The Thomas Burke Memorial Washington State Museum (Burke...

75 FR 36671 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2010-06-28

... DEPARTMENT OF THE INTERIOR National Park Service Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of Washington, Seattle, WA; Correction AGENCY: National Park... human remains and associated funerary objects in the possession of the Thomas Burke Memorial Washington...

76 FR 58034 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2011-09-19

... DEPARTMENT OF THE INTERIOR National Park Service [2253-665] Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of Washington, Seattle, WA AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The Thomas Burke Memorial Washington State Museum (Burke...

76 FR 58039 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2011-09-19

... DEPARTMENT OF THE INTERIOR National Park Service [2253-665] Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of Washington, Seattle, WA AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The Thomas Burke Memorial Washington State Museum (Burke...

Collection Development Policy: Federal Government Publications at Eastern Washington University Libraries.

Science.gov (United States)

Roselle, Ann; Chan, Karen

This collection development policy serves as a guide for the selection and retention of depository government documents by the Government Publications Unit of the Kennedy Memorial Library of Eastern Washington University (EWU) in Cheney, Washington. The library selects approximately 65 percent of the depository items distributed by the U.S.…

The Impact of Interstate Migration on Human Capital Development in Washington

Science.gov (United States)

Spaulding, Randy

2010-01-01

Washington State is a leader in the innovation economy largely due to the combination of aerospace, software, and biomedical industries centered in the greater Seattle area; and, the state's high level of international trade. Despite Washington's national ranking, the state is overly reliant on importing educated workers from other states and…

Flush-mounting technique for composite beams

Science.gov (United States)

Harman, T. C.; Kay, B. F.

1980-01-01

Procedure permits mounting of heavy parts to surface of composite beams without appreciably weakening beam web. Web is split and held apart in region where attachment is to be made by lightweight precast foam filler. Bolt hole penetrates foam rather than web, and is secured by barrelnut in transverse bushing through web.

Making sense of Mount St. Helens

Science.gov (United States)

Steve Nash

2010-01-01

The eruption of Mount St. Helens in 1980 resulted in "a grand experiment that you could never have gotten anybody to fund," says Forest Service ecologist Charles Crisafulli. "Everything's new. It's a new landform." Unlike most misbehaving volcanoes, this one provided an accessible laboratory right along the Interstate-5 corridor, with the...

Washington Schools Learn from Value Engineering.

Science.gov (United States)

Doleae, Michael L.; Childs, Harvey C.

1983-01-01

Results of two value engineering studies have shown that a review early in the design process can help save costs in school construction, maintenance, operation, and replacement. The value engineering concepts and technical manual are being presented throughout the state of Washington. (MLF)

May 1980 Mount Saint Helens, USA Images

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — An earthquake occurred at 15 32 UT, only seconds before the explosion that began the eruption of Mount St. Helens volcano. This eruption and blast blew off the top...

Measurement & Minimization of Mount Induced Strain on Double Crystal Monochromator Crystals

Science.gov (United States)

Kelly, J.; Alcock, S. G.

2013-03-01

Opto-mechanical mounts can cause significant distortions to monochromator crystals and mirrors if not designed or implemented carefully. A slope measuring profiler, the Diamond-NOM [1], was used to measure the change in tangential slope as a function of crystal clamping configuration and load. A three point mount was found to exhibit the lowest surface distortion (Diamond Light Source.

Aerodynamic Optimization of an Over-the-Wing-Nacelle-Mount Configuration

OpenAIRE

Sasaki, Daisuke; Nakahashi, Kazuhiro

2011-01-01

An over-the-wing-nacelle-mount airplane configuration is known to prevent the noise propagation from jet engines toward ground. However, the configuration is assumed to have low aerodynamic efficiency due to the aerodynamic interference effect between a wing and a nacelle. In this paper, aerodynamic design optimization is conducted to improve aerodynamic efficiency to be equivalent to conventional under-the-wing-nacelle-mount configuration. The nacelle and wing geometry are modified to achiev...

77 FR 46117 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2012-08-02

... DEPARTMENT OF THE INTERIOR National Park Service [NPS-WASO-NAGPRA-10823; 2200-1100-665] Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of Washington, Seattle, WA AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The Thomas Burke Memorial Washington...

78 FR 11675 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2013-02-19

... DEPARTMENT OF THE INTERIOR National Park Service [NPS-WASO-NAGPRA-12080;2200-1100-665] Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of Washington, Seattle, WA AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The Thomas Burke Memorial Washington...

Tilt signals at Mount Melbourne, Antarctica: evidence of a shallow volcanic source

Directory of Open Access Journals (Sweden)

Salvatore Gambino

2016-06-01

Full Text Available Mount Melbourne (74°21′ S, 164°43′ E is a quiescent volcano located in northern Victoria Land, Antarctica. Tilt signals have been recorded on Mount Melbourne since early 1989 by a permanent shallow borehole tiltmeter network comprising five stations. An overall picture of tilt, air and permafrost temperatures over 15 years of continuous recording data is reported. We focused our observations on long-term tilt trends that at the end of 1997 showed coherent changes at the three highest altitude stations, suggesting the presence of a ground deformation source whose effects are restricted to the summit area of Mount Melbourne. We inverted these data using a finite spherical body source, thereby obtaining a shallow deflation volume source located under the summit area. The ground deformation observed corroborates the hypothesis that the volcanic edifice of Mount Melbourne is active and should be monitored multidisciplinarily.

Increased earthquake safety through optimised mounting concept

International Nuclear Information System (INIS)

Kollmann, Dieter; Senechal, Holger

2013-01-01

Since Fukushima, there has been intensive work on earthquake safety in all nuclear power plants. A large part of these efforts aim at the earthquake safety of safety-relevant pipeline systems. The problem with earthquake safety here is not the pipeline system itself but rather its mountings and connections to components. This is precisely the topic that the KAE dealt with in years of research and development work. It has developed an algorithm that determines the optimal mounting concept with a few iteration steps depending on arbitrary combinations of loading conditions whilst maintaining compliance with relevant regulations for any pipeline systems. With this tool at hand, we are now in a position to plan and realise remedial measures accurately with minimum time and hardware expenditure, and so distinctly improve the earthquake safety of safety-relevant systems. (orig.)

Preparation of source mounts for 4π counting

International Nuclear Information System (INIS)

Johnson, E.P.

1991-01-01

The 4πβ/γ counter in the ANSTO radioisotope standards laboratory at Lucas Heights constitutes part of the Australian national standard for radioactivity. Sources to be measured in the counter must be mounted on a substrate which is strong enough to withstand careful handling and transport. The substrate must also be electrically conducting to minimise counting errors caused by charging of the source, and it must have very low superficial density so that little or none of the radiation is absorbed. The entire process of fabrication of VYNS films, coating them with gold/palladium and transferring them to source mount rings, as carried out in the radioisotope standards laboratory, is documented. 3 refs., 2 tabs., 6 figs

Monitoring of Olympic National Park Beaches to determine fate and effects of spilled bunker C fuel oil

Energy Technology Data Exchange (ETDEWEB)

Strand, J.A.; Cullinan, V.I.; Crecelius, E.A.; Fortman, T.J.; Citterman, R.J.; Fleischmann, M.L.

1990-10-01

On December 23, 1988, the barge Nestucca was accidentally struck by its tow, a Souse Brothers Towing Company tug, releasing approximately 230,000 gallons of Bunker C fuel oil and fouling beaches from Grays Harbor north to Vancouver Island. Affected beaches in Washington included a 40-mile-long strip that has been recently added to Olympic National Park. The purpose of the monitoring program documented in this report was to determine the fate of spilled Bunker C fuel oil on selected Washington coastal beaches. We sought to determine (1) how much oil remained in intertidal and shallow subtidal habitats following clean-up and weathering, (2) to what extent intertidal and/or shallow subtidal biotic assemblages have been contaminated, and (3) how rapidly the oil has left the ecosystem. 45 refs., 18 figs., 8 tabs.

New Az/El mount for Haystack Observatory's Small Radio Telescope kit

Science.gov (United States)

Cobb, M. L.

2005-12-01

The Small Radio Telescope (SRT) kit was designed by Haystack Observatory as part of their educational outreach effort. The SRT uses a custom designed FFT based radio spectrometer receiver with a controller to position a 2.3m dish to make various radio astronomy observations including the 21 cm spin flip line of atomic hydrogen. Because there is no sizable commercial market for a two dimensional mount for dishes of this size, finding an appropriate provider as been a recurring problem for the project. Originally, the kit used a modified motor mount from Kaultronics called the H180. Two of these motors were combined by a specially designed adaptor to allow motion in azimuth and elevation. When Kaultronics was bought out by California Amplifier they discontinued production of the H180. The next iteration used a compact unit called the alfa-spid which was made in Germany and imported through Canada. The alfa-spid was designed to point various ham radio antennas and proved problematic with 2.3m dishes. Most recently the CASSI (Custom Astronomical Support Services, Inc.) corporation has designed and certified a robust Az/El mount capable of supporting dishes up to 12 feet (3.6m) with 100 MPH wind loads. This paper presents the design and operating characteristics of the new CASSI mount. The CASSI mount is now shipped with the SRT kit and should serve the project well for the foreseeable future.

Integrated Digital English Acceleration (I-DEA). Washington's Community and Technical Colleges

Science.gov (United States)

Washington State Board for Community and Technical Colleges, 2015

2015-01-01

Washington state has a large and rapidly growing foreign-born population. In 2011, immigrants made up 16.5 percent of Washington's civilian employed workforce, up from 7.1 percent in 1990. These new arrivals create jobs by forming businesses, spending income in local economies and raising employers' productivity. Thanks to project I-DEA…

GNSS Signal Tracking Performance Improvement for Highly Dynamic Receivers by Gyroscopic Mounting Crystal Oscillator.

Science.gov (United States)

Abedi, Maryam; Jin, Tian; Sun, Kewen

2015-08-31

In this paper, the efficiency of the gyroscopic mounting method is studied for a highly dynamic GNSS receiver's reference oscillator for reducing signal loss. Analyses are performed separately in two phases, atmospheric and upper atmospheric flights. Results show that the proposed mounting reduces signal loss, especially in parts of the trajectory where its probability is the highest. This reduction effect appears especially for crystal oscillators with a low elevation angle g-sensitivity vector. The gyroscopic mounting influences frequency deviation or jitter caused by dynamic loads on replica carrier and affects the frequency locked loop (FLL) as the dominant tracking loop in highly dynamic GNSS receivers. In terms of steady-state load, the proposed mounting mostly reduces the frequency deviation below the one-sigma threshold of FLL (1σ(FLL)). The mounting method can also reduce the frequency jitter caused by sinusoidal vibrations and reduces the probability of signal loss in parts of the trajectory where the other error sources accompany this vibration load. In the case of random vibration, which is the main disturbance source of FLL, gyroscopic mounting is even able to suppress the disturbances greater than the three-sigma threshold of FLL (3σ(FLL)). In this way, signal tracking performance can be improved by the gyroscopic mounting method for highly dynamic GNSS receivers.

Design and functional tests of the Euclid grism mount

Science.gov (United States)

Rossin, Ch.; Grange, R.; Caillat, A.; Costille, A.; Sanchez, P.; Ceria, W.

2017-11-01

The Euclid mission selected by ESA in the Cosmic Vision program is dedicated to understand dark energy and dark matter. One of the probes based on detection of Baryonic Acoustic Oscillations required the redshift of millions of galaxies. This massive spectroscopic survey relies on the Near Infrared SpectroPhotometer (NISP) using grism in slitless mode. In this Euclid NISP context, we designed a cryogenic mount for the four grisms of the spectroscopic channel. This mount has to maintain optical performances and alignment at the cryogenic temperature of 120K and to survive launch vibrations. Due to a very small mass and volume budget allowed in the Grism Wheel Assembly our design relies on a weight relief Invar ring glued to the grism by tangential flexures. Tangential flexures have the advantage of small height but the drawback of less decoupling capabilities than bipods. We will present the design of the mount and the integration and functional tests to stay within the 60 nm RMS transmitted wavefront error budget allowed to the grism.

Geologic Map of Mount Mazama and Crater Lake Caldera, Oregon

Science.gov (United States)

Bacon, Charles R.

2008-01-01

Crater Lake partly fills one of the most spectacular calderas of the world, an 8-by-10-km basin more than 1 km deep formed by collapse of the volcano known as Mount Mazama (fig. 1) during a rapid series of explosive eruptions about 7,700 years ago. Having a maximum depth of 594 m, Crater Lake is the deepest lake in the United States. Crater Lake National Park, dedicated in 1902, encompasses 645 km2 of pristine forested and alpine terrain, including the lake itself, virtually all of Mount Mazama, and most of the area of the geologic map. The geology of the area was first described in detail by Diller and Patton (1902) and later by Williams (1942), whose vivid account led to international recognition of Crater Lake as the classic collapse caldera. Because of excellent preservation and access, Mount Mazama, Crater Lake caldera, and the deposits formed by the climactic eruption constitute a natural laboratory for study of volcanic and magmatic processes. For example, the climactic ejecta are renowned among volcanologists as evidence for systematic compositional zonation within a subterranean magma chamber. Mount Mazama's climactic eruption also is important as the source of the widespread Mazama ash, a useful Holocene stratigraphic marker throughout the Pacific Northwest, adjacent Canada, and offshore. A detailed bathymetric survey of the floor of Crater Lake in 2000 (Bacon and others, 2002) provides a unique record of postcaldera eruptions, the interplay between volcanism and filling of the lake, and sediment transport within this closed basin. Knowledge of the geology and eruptive history of the Mount Mazama edifice, greatly enhanced by the caldera wall exposures, gives exceptional insight into how large volcanoes of magmatic arcs grow and evolve. Lastly, the many smaller volcanoes of the High Cascades beyond the limits of Mount Mazama are a source of information on the flux of mantle-derived magma through the region. General principles of magmatic and eruptive

76 FR 19125 - Bottom Mount Combination Refrigerator-Freezers From Korea and Mexico

Science.gov (United States)

2011-04-06

...)] Bottom Mount Combination Refrigerator-Freezers From Korea and Mexico AGENCY: United States International... bottom mount combination refrigerator-freezers from Korea and Mexico, provided for in subheadings 8418.10... five business days thereafter, or by May 23, 2011. For further information concerning the conduct of...

Biodiversity of the flora of Mount Papa

International Nuclear Information System (INIS)

Yin-Yin-Kyi

1995-07-01

Even though Mount Papa is in the dry zone area, it is almost evergreen, due to its elevation of 4981 feet above the sea level and its fertile soil conditions. A has a rich biodiversity with vegetation of many types

The effect of consumers and mutualists of Vaccinium membranaceum at Mount St. Helens: dependence on successional context.

Directory of Open Access Journals (Sweden)

Suann Yang

Full Text Available In contrast to secondary succession, studies of terrestrial primary succession largely ignore the role of biotic interactions, other than plant facilitation and competition, despite the expectation that simplified interaction webs and propagule-dependent demographics may amplify the effects of consumers and mutualists. We investigated whether successional context determined the impact of consumers and mutualists by quantifying their effects on reproduction by the shrub Vaccinium membranaceum in primary and secondary successional sites at Mount St. Helens (Washington, USA, and used simulations to explore the effects of these interactions on colonization. Species interactions differed substantially between sites, and the combined effect of consumers and mutualists was much more strongly negative for primary successional plants. Because greater local control of propagule pressure is expected to increase successional rates, we evaluated the role of dispersal in the context of these interactions. Our simulations showed that even a small local seed source greatly increases population growth rates, thereby balancing strong consumer pressure. The prevalence of strong negative interactions in the primary successional site is a reminder that successional communities will not exhibit the distribution of interaction strengths characteristic of stable communities, and suggests the potential utility of modeling succession as the consequence of interaction strengths.

Washington (Wash) C. Winn: In Memoriam

Centers for Disease Control (CDC) Podcasts

2012-03-08

Dr. Mike Miller and Dr. David Walker dicuss the career and life of noted clinical biologist, Dr. Washington C. Winn Jr.  Created: 3/8/2012 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 3/12/2012.

Fathead minnow whole-mount in situ hybridization (WISH)

Data.gov (United States)

U.S. Environmental Protection Agency — This study demonstrates the potential of whole-mount in situ hybridization (WISH), in conjunction with quantitative real-time polymerase chain reaction (QPCR)...

78 FR 64006 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2013-10-25

... inventory of human remains under the control of the Burke Museum. The human remains were removed from Island....R50000] Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of... Memorial Washington State Museum, University of Washington (Burke Museum), has completed an inventory of...

78 FR 59955 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2013-09-30

... completion of an inventory of human remains under the control of the Burke Museum, Seattle, WA. The human....R50000] Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of... Memorial Washington State Museum, University of Washington (Burke Museum), has completed an inventory of...

Aerodynamic interaction effects of tip-mounted propellers installed on the horizontal tailplane

NARCIS (Netherlands)

van Arnhem, N.; Sinnige, T.; Stokkermans, T.C.A.; Eitelberg, G.; Veldhuis, L.L.M.

2018-01-01

This paper addresses the effects of propeller installation on the aerodynamic performance of a tailplane featuring tip-mounted propellers. A model of a low aspect ratio tailplane equipped with an elevator and a tip-mounted propeller was installed in a low-speed wind-tunnel. Measurements were

Wirebond crosstalk and cavity modes in large chip mounts for superconducting qubits

Energy Technology Data Exchange (ETDEWEB)

Wenner, J; Neeley, M; Bialczak, Radoslaw C; Lenander, M; Lucero, Erik; O' Connell, A D; Sank, D; Wang, H; Weides, M; Cleland, A N; Martinis, John M, E-mail: martinis@physics.ucsb.edu [Department of Physics, University of California, Santa Barbara, CA 93106 (United States)

2011-06-15

We analyze the performance of a microwave chip mount that uses wirebonds to connect the chip and mount grounds. A simple impedance ladder model predicts that transmission crosstalk between two feedlines falls off exponentially with distance at low frequencies, but rises to near unity above a resonance frequency set by the chip to ground capacitance. Using SPICE simulations and experimental measurements of a scale model, the basic predictions of the ladder model were verified. In particular, by decreasing the capacitance between the chip and box grounds, the resonance frequency increased and transmission decreased. This model then influenced the design of a new mount that improved the isolation to - 65 dB at 6 GHz, even though the chip dimensions were increased to 1 cm x 1 cm, three times as large as our previous devices. We measured a coplanar resonator in this mount as preparation for larger qubit chips, and were able to identify cavity, slotline, and resonator modes.

Wirebond crosstalk and cavity modes in large chip mounts for superconducting qubits

International Nuclear Information System (INIS)

Wenner, J; Neeley, M; Bialczak, Radoslaw C; Lenander, M; Lucero, Erik; O'Connell, A D; Sank, D; Wang, H; Weides, M; Cleland, A N; Martinis, John M

2011-01-01

We analyze the performance of a microwave chip mount that uses wirebonds to connect the chip and mount grounds. A simple impedance ladder model predicts that transmission crosstalk between two feedlines falls off exponentially with distance at low frequencies, but rises to near unity above a resonance frequency set by the chip to ground capacitance. Using SPICE simulations and experimental measurements of a scale model, the basic predictions of the ladder model were verified. In particular, by decreasing the capacitance between the chip and box grounds, the resonance frequency increased and transmission decreased. This model then influenced the design of a new mount that improved the isolation to - 65 dB at 6 GHz, even though the chip dimensions were increased to 1 cm x 1 cm, three times as large as our previous devices. We measured a coplanar resonator in this mount as preparation for larger qubit chips, and were able to identify cavity, slotline, and resonator modes.

NSA Diana Wueger Published in Washington Quarterly

OpenAIRE

Grant, Catherine L.

2016-01-01

National Security Affairs (NSA) News NSA Faculty Associate for Research Diana Wueger has recently had an article titled “India’s Nuclear-Armed Submarines: Deterrence or Danger?” published in the Washington Quarterly.

Bearing-Mounting Concept Accommodates Thermal Expansion

Science.gov (United States)

Nespodzany, Robert; Davis, Toren S.

1995-01-01

Pins or splines allow radial expansion without slippage. Design concept for mounting rotary bearing accommodates differential thermal expansion between bearing and any structure(s) to which bearing connected. Prevents buildup of thermal stresses by allowing thermal expansion to occur freely but accommodating expansion in such way not to introduce looseness. Pin-in-slot configuration also maintains concentricity.

Fixture For Mounting A Pressure Sensor

Science.gov (United States)

Cagle, Christopher M.

1995-01-01

Fixture for mounting pressure sensor in aerodynamic model simplifies task of removal and replacement of sensor in event sensor becomes damaged. Makes it unnecessary to dismantle model. Also minimizes any change in aerodynamic characteristics of model in event of replacement. Removable pressure sensor installed in fixture in wall of model. Wires from sensor pass through channel under surface.

Crustal inheritance and arc magmatism: Magnetotelluric constraints from the Washington Cascades on top-down control

Science.gov (United States)

Bedrosian, P.; Peacock, J.; Bowles-martinez, E.; Schultz, A.; Hill, G.

2017-12-01

Worldwide, arc volcanism occurs along relatively narrow magmatic arcs, the locations of which are considered to mark the onset of dehydration reactions within the subducting slab. This `bottom-up' approach, in which the location of arc volcanism reflects where fluids and melt are generated, explains first-order differences in trench-to-arc distance and is consistent with known variations in the thermal structure and geometry of subducting slabs. At a finer scale, arc segmentation, magmatic gaps, and anomalous forearc and backarc magmatism are also frequently interpreted in terms of variations in slab geometry, composition, or thermal structure.The role of inherited crustal structure in controlling faulting and deformation is well documented; less well examined is the role of crustal structure in controlling magmatism. While the source distribution of melt and subduction fluids is critical to determining the location of arc magmatism, we argue that crustal structure provides `top-down' control on patterns or seismicity and deformation as well as the channeling and ascent of arc magmas. We present evidence within the Washington Cascades based upon correlation between a new three-dimensional resistivity model, potential-field data, seismicity, and Quaternary volcanism. We image a mid-Tertiary batholith, intruded within an Eocene crustal suture zone, and extending throughout much of the crustal column. This and neighboring plutons are interpreted to channel crustal fluids and melt along their margins within steeply dipping zones of marine to transitional metasedimentary rock. Mount St. Helens is interpreted to be fed by fluids and melt generated further east at greater slab depths, migrating laterally (underplating?) beneath the Spirit Lake batholith, and ascending through metasedimentary rocks within the brittle crust. At a regional scale, we argue that this concealed suture zone controls present-day deformation and seismicity as well as the distribution of forearc

The Effects of Degradational Factors on the Ecosystem of Mount Madra

Science.gov (United States)

Efe, R.; Soykan, A.; Sönmez, S.; Cürebal, I.

2009-04-01

Significant degradation has been observed in Turkey's Mediterranean woodlands and mountainous areas. Mediterranean climate prevails in the southern and western part of Turkey. Mount Madra, which is located on Turkey's western Aegean coast, is part of a rangeland which is particularly exposed to the effects of degradation resulting from human activities. The principal factors in the degradation are inappropriate land use, destruction of forests, mining, construction, overgrazing and transhumance. Mount Madra and its environs benefit from a Mediterranean climate, experiencing dry, hot summers and cool, wet winters. The average yearly rainfall is 700-1000 mm, of which most occurs in the winter months. The mountain extends from east to west, and between the South and North slopes there is great variety in terms of plant species and biodiversity. The regeneration of the lost plant cover has been hindered by the mountain's geomorphologic characteristics. The slopes have suffered destruction of vegetation and, as a result of severe erosion, the soil has been swept away and in many places the bedrock has become exposed. The Kozak plateau on mount Madra is notable for the richness of its natural vegetation. This plateau, covered in pine forest (Pinus pinea), is the site for the traditional transhumance of over 500 families. Pine nuts and livestock breeding are livelihood of these families. Mount Madra and its surrounding area is one of the most important locations with gold mining potential in Turkey and it is estimated that it has 16.7 tons of gold reserve. The gold mining which took place on the west of the Madra Mountain around Ovacik village in 1994 led to serious land degradation in the surrounding area. The new mining on the study area and the proposed feldspar mining on the Madra riverbed poses a serious threat to the region's ecosystem and biodiversity. The removal of increasing amounts of granite and other quarrying has had a negative impact on the natural

Bibliography of the geology of the Columbia Basin and surrounding areas of Washington

International Nuclear Information System (INIS)

Tucker, G.B.; Rigby, J.G.

1979-07-01

In the fall of 1977, the Washington State Department of Natural Resources, Division of Geology and Earth Resources (WDGER), entered into a contract with the US Department of Energy, administered by Rockwell Hanford Operations (Rockwell) in Richland, Washington, as a principal contributor to a geologic study of feasibility of storing radioactive waste within Columbia River basalt. WDGER's responsibility was the production of this bibliography and a reconnaissance geologic map of the sediments overlying the Columbia River Basalt Group in the State of Washington. This bibliography is a compilation of all known published, unpublished, and open-file references dealing with geology and geophysics of the Columbia Basin of eastern Washington. The citations were obtained primarily from the WDGER and Washington State libraries; the Geo-Ref bibliographic system was also utilized. Because the WDGER portion of the study included preparation of a reconnaissance geologic map of surficial deposits in the Columbia Basin, available references dealing with this subject have been annotated. Many abstracts in the annotated section are quotations and have been copied directly from their respective publications

Bibliography of the geology of the Columbia Basin and surrounding areas of Washington

Energy Technology Data Exchange (ETDEWEB)

Tucker, G.B.; Rigby, J.G.

1979-07-01

In the fall of 1977, the Washington State Department of Natural Resources, Division of Geology and Earth Resources (WDGER), entered into a contract with the US Department of Energy, administered by Rockwell Hanford Operations (Rockwell) in Richland, Washington, as a principal contributor to a geologic study of feasibility of storing radioactive waste within Columbia River basalt. WDGER's responsibility was the production of this bibliography and a reconnaissance geologic map of the sediments overlying the Columbia River Basalt Group in the State of Washington. This bibliography is a compilation of all known published, unpublished, and open-file references dealing with geology and geophysics of the Columbia Basin of eastern Washington. The citations were obtained primarily from the WDGER and Washington State libraries; the Geo-Ref bibliographic system was also utilized. Because the WDGER portion of the study included preparation of a reconnaissance geologic map of surficial deposits in the Columbia Basin, available references dealing with this subject have been annotated. Many abstracts in the annotated section are quotations and have been copied directly from their respective publications.

Death with dignity in Washington patients with amyotrophic lateral sclerosis.

Science.gov (United States)

Wang, Leo H; Elliott, Michael A; Jung Henson, Lily; Gerena-Maldonado, Elba; Strom, Susan; Downing, Sharon; Vetrovs, Jennifer; Kayihan, Paige; Paul, Piper; Kennedy, Kate; Benditt, Joshua O; Weiss, Michael D

2016-11-15

To describe the amyotrophic lateral sclerosis (ALS) patients who sought medication under the Washington State Death with Dignity (DWD) Act since its inception in 2009. Chart review at 3 tertiary medical centers in the Seattle/Puget Sound region and comparison to publicly available data of ALS and all-cause DWD cohorts from Washington and Oregon. In Washington State, 39 patients with ALS requested DWD from the University of Washington, Virginia Mason, and Swedish Medical Centers beginning in 2009. The median age at death was 65 years (range 46-86). Seventy-seven percent of the patients used the prescriptions. All of the patients who used the medications passed away without complications. The major reasons for patients to request DWD as reported by participating physicians were loss of autonomy and dignity and decrease in enjoyable activities. Inadequate pain control, financial cost, and loss of bodily control were less commonly indicated. These findings were similar to those of the 92 patients who sought DWD in Oregon. In Washington and Oregon, the percentage of patients with ALS seeking DWD is higher compared to the cancer DWD cohort. Furthermore, compared to the all-cause DWD cohort, patients with ALS are more likely to be non-Hispanic white, married, educated, enrolled in hospice, and to have died at home. Although a small number, ALS represents the disease with the highest proportion of patients seeking to participate in DWD. Patients with ALS who choose DWD are well-educated and have access to palliative or life-prolonging care. The use of the medications appears to be able to achieve the patients' goals without complications. © 2016 American Academy of Neurology.

78 FR 59964 - Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of...

Science.gov (United States)

2013-09-30

....S.C. 3003, of the completion of an inventory of human remains under the control of the Burke Museum....R50000] Notice of Inventory Completion: Thomas Burke Memorial Washington State Museum, University of... Washington (Burke Museum), and Central Washington University have completed an inventory of human remains, in...

Seroadaptive Strategies of Gay & Bisexual Men (GBM) with the Highest Quartile Number of Sexual Partners in Vancouver, Canada.

Science.gov (United States)

Card, Kiffer G; Lachowsky, Nathan J; Cui, Zishan; Sereda, Paul; Rich, Ashleigh; Jollimore, Jody; Howard, Terry; Birch, Robert; Carter, Allison; Montaner, Julio; Moore, David; Hogg, Robert S; Roth, Eric Abella

2017-05-01

Despite continued research among men with more sexual partners, little information exists on their seroadaptive behavior. Therefore, we examined seroadaptive anal sex strategies among 719 Vancouver gay and bisexual men (GBM) recruited using respondent-driven sampling. We provide descriptive, bivariable, and multivariable adjusted statistics, stratified by HIV status, for the covariates of having ≥7 male anal sex partners in the past 6 months (Population fourth quartile versus <7). Sensitivity Analysis were also performed to assess the robustness of this cut-off. Results suggest that GBM with more sexual partners are more likely to employ seroadaptive strategies than men with fewer partners. These strategies may be used in hopes of offsetting risk, assessing needs for subsequent HIV testing, and balancing personal health with sexual intimacy. Further research is needed to determine the efficacy of these strategies, assess how GBM perceive their efficacy, and understand the social and health impacts of their widespread uptake.

PUBLICATION BANS IN A FACEBOOK AGE: HOW INTERNET VIGILANTES HAVE CHALLENGED THE YOUTH CRIMINAL JUSTICE ACT’S “SECRECY LAWS” FOLLOWING THE 2011 VANCOUVER STANLEY CUP RIOT

Directory of Open Access Journals (Sweden)

Tania Arvanitidis

2016-08-01

Full Text Available On June 15th, 2011, a hockey riot occurred in Vancouver, British Columbia. This event is prominent in Canada’s history for, among other reasons, the unprecedented extent to which it was documented via photographs and video footage. The days that followed the riot saw much of this media documentation uploaded to social media platforms on the Internet, where Internet users worked together to identify and collectively “name and shame” those believed to have been involved in the disturbance. Several individuals targeted by these “Internet vigilantes” were young offenders whose identities are legally protected from publication under the Youth Criminal Justice Act (YCJA. This article examines the phenomenon of “Internet vigilantism”, and raises the issue of whether those provisions within the YCJA that prohibit the identification of youth remain relevant today, given the current difficulties in enforcing these provisions. Following an overview of these “secrecy provisions”, the phenomenon of Internet vigilantism is defined, and challenges posed by acts of Internet vigilantism are discussed. A “naming and shaming” Facebook group created for the purpose of identifying participants in the 2011 Vancouver riot is then looked to as a case study of Internet vigilantism in action. This article concludes with recommendations for how justice officials and social media outlets may modify current practices to better protect the safety and security of young offenders, and to minimize harmful instances of Internet vigilantism.

Fuel management at Washington State Ferries

International Nuclear Information System (INIS)

Brodeur, P.; Olds, J.

2008-01-01

This presentation discussed Washington State Ferry (WSF) operations and provided details of a biodiesel research and demonstration project. Washington has the largest ferry system in the United States, with a total of 28 vessels that operate on 10 routes through 20 terminals. Routes vary by transit times, navigational challenges, and the proximity to population centres. WSF fuel and emissions management initiatives include exhaust emission studies, clean fuel initiatives, machinery upgrades, fuel conservation initiatives, and biodiesel testing. The organization is also using waste heat recovery and a positive restraint system. The WSF biodiesel pilot program was conducted using soy-derived fuels with a purifier disk stack. The program is in agreement with recent legislation requiring that 2 per cent of annual diesel fuel sales are from biodiesel fuels, and state legislation requiring that state agencies use a minimum of 20 per cent biodiesel blends in diesel-powered vessels and vehicles. Details of project partnerships were included. tabs., figs

Low-temperature geothermal resources of Washington

Energy Technology Data Exchange (ETDEWEB)

Schuster, J.E. [Washington State Dept. of Natural Resources, Olympia, WA (United States). Div. of Geology and Earth Resources; Bloomquist, R.G. [Washington State Energy Office, Olympia, WA (United States)

1994-06-01

This report presents information on the location, physical characteristics, and water chemistry of low-temperature geothermal resources in Washington. The database includes 941 thermal (>20C or 68F) wells, 34 thermal springs, lakes, and fumaroles, and 238 chemical analyses. Most thermal springs occur in the Cascade Range, and many are associated with stratovolcanoes. In contrast, 97 percent of thermal wells are located in the Columbia Basin of southeastern Washington. Some 83.5 percent are located in Adams, Benton, Franklin, Grant, Walla Walla, and Yakima Counties. Yakima County, with 259 thermal wells, has the most. Thermal wells do not seem to owe their origin to local sources of heat, such as cooling magma in the Earth`s upper crust, but to moderate to deep circulation of ground water in extensive aquifers of the Columbia River Basalt Group and interflow sedimentary deposits, under the influence of a moderately elevated (41C/km) average geothermal gradient.

Marine vessel air emissions in B.C. and Washington State outside the GVRD and FVRD for the year 2000

International Nuclear Information System (INIS)

Quan, R.G.; Trask, T.C.; Cheng, K.C.

2002-01-01

Emissions inventories are used by government agencies as a tool for policy development and air quality management. Marine vessels have been identified as a major source of anthropogenic pollution in British Columbia. This report presents estimates of emissions from marine vessels in coastal areas in British Columbia outside of the Greater Vancouver Regional District (GVRD), the Fraser Valley Regional District (FVRD), and in Washington State for the year 2000. The project includes an update of emission estimates for each marine vessel category and an update of emission estimates for pollutants of interest, including carbon monoxide (CO), nitrogen oxides (NOx), particulate matter (PM), sulphur oxides (SOx), volatile organic compounds (VOCs), as well as inhalable fine particulates (PM10 and PM2.5) and greenhouse gases such as carbon dioxide, methane, nitrous oxide and ammonia. This report presented emissions results for both the Canadian and U.S. portions. It also includes both spatial and temporal allocation of emissions. Results indicate that ocean-going vessels are the major contributor to emissions of NOx, SOx, PM and greenhouse gases, accounting for 56, 93, 83, and 51 per cent of the total marine vessel emissions respectively. They also contribute 30 and 33 per cent to the marine totals for CO and VOCs. Harbour vessels contribute 22 and 24 per cent of NOx and greenhouse gases and 17 per cent of both CO and VOCs. Ferries contribute between 15 per cent and 23 per cent for CO, VOC, NOx and GHGs, but less than 9 per cent for SOx and PM. Fishing vessels contribute 1 per cent or less of all contaminants. Although recreational vessels are major contributors for CO and VOC, they contribute less than 2 per cent for all other contaminants. A comparison of 1995 and 2000 marine vessel inventory for British Columbia was presented and recommendations for improvements were presented. refs., tabs., figs.

Examining risk factors for cardiovascular disease among food bank members in Vancouver.

Science.gov (United States)

Fowokan, A O; Black, J L; Holmes, E; Seto, D; Lear, S A

2018-06-01

Food banks provide supplemental food to low-income households, yet little is known about the cardiovascular health of food banks members. This study therefore described cardiovascular disease (CVD) risk factors among food bank members and explored associations between food insecurity and CVD risk. Adults ≥18 years (n = 77) from three food bank sites in metro Vancouver, British Columbia completed surveys and physical assessments examining a range of socio-demographic variables and CVD risk factors. A composite measure of myocardial infarction (MI) risk called the INTERHEART score was assessed and household food insecurity was measured using the Household Food Security Survey Module. Regression models were used to explore associations between food insecurity and CVD risk measures, including the INTERHEART score. Ninety-seven percent of food bank members reported experiencing food insecurity, 65% were current smokers, 53% reported either chronic or several periods of stress in the past year, 55% reported low physical activity levels and 80% reported consuming fewer than five servings of fruit and vegetables daily. Prevalence of self-reported diabetes and hypertension were 13% and 29% respectively. Fifty-two percent of the sample were at high risk of non-fatal MI. No statistically significant associations were found between increased severity of food insecurity and CVD risk factors among this sample where both severe food insecurity and high CVD risks were prevalent. Food bank members were at elevated risk for CVD compared with the general population. Strategies are needed to reduce prevalence of food insecurity and CVD risk factors, both of which disproportionately affected food bank members.

Fluorescent visualization of macromolecules in Drosophila whole mounts.

Science.gov (United States)

Ramos, Ricardo Guelerman Pinheiro; Machado, Luciana Claudia Herculano; Moda, Livia Maria Rosatto

2010-01-01

The ability to determine the expression dynamics of individual genes "in situ" by visualizing the precise spatial and temporal distribution of their products in whole mounts by histochemical and immunocytochemical reactions has revolutionized our understanding of cellular processes. Drosophila developmental genetics was one of the fields that benefited most from these technologies, and a variety of fluorescent methods were specifically designed for investigating the localization of developmentally important proteins and cell markers during embryonic and post embryonic stages of this model organism. In this chapter we present detailed protocols for fluorescence immunocytochemistry of whole mount embryos, imaginal discs, pupal retinas, and salivary glands of Drosophila melanogaster, as well as methods for fluorescent visualization of specific subcellular structures in these tissues.

Southwestern Washington 1/3 arc-second DEM

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The 1/3-second Southwest Washington Elevation Grid provides bathymetric data in ASCII raster format of 1/3-second resolution in geographic coordinates. This grid is...

Genetic structure of Mount Huang honey bee (Apis cerana) populations: evidence from microsatellite polymorphism.

Science.gov (United States)

Liu, Fang; Shi, Tengfei; Huang, Sisi; Yu, Linsheng; Bi, Shoudong

2016-01-01

The Mount Huang eastern honey bees ( Apis cerana ) are an endemic population, which is well adapted to the local agricultural and ecological environment. In this study, the genetic structure of seven eastern honey bees ( A. cerana ) populations from Mount Huang in China were analyzed by SSR (simple sequence repeat) markers. The results revealed that 16 pairs of primers used amplified a total of 143 alleles. The number of alleles per locus ranged from 6 to 13, with a mean value of 8.94 alleles per locus. Observed and expected heterozygosities showed mean values of 0.446 and 0.831 respectively. UPGMA cluster analysis grouped seven eastern honey bees in three groups. The results obtained show a high genetic diversity in the honey bee populations studied in Mount Huang, and high differentiation among all the populations, suggesting that scarce exchange of honey bee species happened in Mount Huang. Our study demonstrated that the Mount Huang honey bee populations still have a natural genome worth being protected for conservation.

Report on the FY 1987 potential survey of overseas coal development. Nanaimo coal field, Vancouver island, State of British Columbia, Canada; 1987 nendo kaigaitan kaihatsu kanosei chosa hokokusho. Canada British Columbia shu Vancouver to Nanaimo tanden

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

In Vancouver island, coal deposits which are economically minable can be found only in Comox sub-basin and Nanaimo sub-basin. In the Nanaimo coal field, 110 coal deposits have been operated, and a total of 54.39 million MT coal was drilled and shipped. The coal reserve of approximately 90 million MT seems to be still left, but it is hard to know how much the minable coal is in the case only of within 300m below earth's surface. In the Comox coal field, there seems to be still left the coal reserve as much as approximately 1.3 billion MT. The coal of the Nanaimo coal field is ranked as high volatile 'A' bituminous, the same as the coal of the Comox coal field. In the Wolf Mountain coal mining area, there is the minable coal of approximately 2.4 million MT in the undeveloped portion. The clean coal to be produced came to be regarded as good for shipment to Japan not only as steam coal but as slightly caking coal if it is competitive in cost as viewed from the coal quality expected. (NEDO)

Report on the FY 1987 potential survey of overseas coal development. Nanaimo coal field, Vancouver island, State of British Columbia, Canada; 1987 nendo kaigaitan kaihatsu kanosei chosa hokokusho. Canada British Columbia shu Vancouver to Nanaimo tanden

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

In Vancouver island, coal deposits which are economically minable can be found only in Comox sub-basin and Nanaimo sub-basin. In the Nanaimo coal field, 110 coal deposits have been operated, and a total of 54.39 million MT coal was drilled and shipped. The coal reserve of approximately 90 million MT seems to be still left, but it is hard to know how much the minable coal is in the case only of within 300m below earth's surface. In the Comox coal field, there seems to be still left the coal reserve as much as approximately 1.3 billion MT. The coal of the Nanaimo coal field is ranked as high volatile 'A' bituminous, the same as the coal of the Comox coal field. In the Wolf Mountain coal mining area, there is the minable coal of approximately 2.4 million MT in the undeveloped portion. The clean coal to be produced came to be regarded as good for shipment to Japan not only as steam coal but as slightly caking coal if it is competitive in cost as viewed from the coal quality expected. (NEDO)

Method and apparatus for mounting or dismounting a semi-automatic twist-lock

NARCIS (Netherlands)

Klein Breteler, A.J.; Tekeli, G.

2001-01-01

The invention relates to a method for mounting or dismounting a semi-automatic twistlock at a corner of a deck container, wherein the twistlock is mounted or dismounted on a quayside where a ship may be docked for loading or unloading, in a loading or unloading terminal installed on the quayside,

Local Sabahans’ Satisfaction with Level of Access to Mount Kinabalu

Directory of Open Access Journals (Sweden)

Bidder Christy

2014-01-01

Full Text Available This study analyzes the local Sabahans’ satisfaction with the level of access to Mount Kinabalu in Sabah, Malaysian Borneo. Specifically, it examines the number of complaints by local Sabahans regarding access and their perception of changes in accessibility to the mountain. Interviews with Sabah Parks and Sutera Sanctuary Lodges were conducted and questionnaires were distributed to local residents to collect data. The results show that there were intense complaints regarding the climbing cost and extensive waiting time to secure a confirmed booking at the outset of price increases. However, the researchers could not locate any recently published complaints. Respondents who have previously climbed Mount Kinabalu perceive the mountain to be less accessible for local Sabahans now due to a less affordable cost and a longer waiting time. Those who have not climbed Mount Kinabalu also think the climbing cost has become less affordable for local Sabahans, but they do not perceive that to be causing the mountain less accessible for local Sabahans.

A 2015 comparison of operational performance : Washington state ferries to ferry operators worldwide.

Science.gov (United States)

2015-03-01

This report provides an update to the 2010 report A Comparison of Operational Performance: : Washington State Ferries to Ferry Operators Worldwide, observing changes in Washington State : Ferries, 23 other ferry systems, and the ferry industry ...

Nonlinear adaptive observer-based sliding mode control for LAMOST mount driving

International Nuclear Information System (INIS)

Zhou Wangping; Guo Wei; Yu Li; Yang Changsong; Zheng Yi

2010-01-01

Heavy disturbances caused mainly by wind and friction in the mount drive system greatly impair the pointing accuracy of the Large Sky Area Multi-Object Fiber Spectroscopic Telescope (LAMOST). To overcome this negative effect, a third order Higher Order Sliding Mode (HOSM) controller is proposed. The key part of this approach is to design an appropriate observer which obtains the acceleration state. A nonlinear adaptive observer is proposed in which a novel polynomial model is applied to estimate the internal disturbances of the mount drive system. Theoretical analysis demonstrates the stability of the proposed observer. Simulation results show that this nonlinear adaptive observer can obtain a high precision acceleration signal which completes the HOSM controller. Furthermore, the HOSM approach can easily satisfy the position tracking requirements of the LAMOST mount drive system.

Willapa Bay, Washington Benthic Habitats 1995 Biotic

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — In June 1995, the Columbia River Estuary Study Taskforce (CREST) acquired 295 true color aerial photographs (1:12,000) of Willapa Bay, Washington, from the State of...

Willapa Bay, Washington Benthic Habitats 1995 Geoform

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — In June 1995, the Columbia River Estuary Study Taskforce (CREST) acquired 295 true color aerial photographs (1:12,000) of Willapa Bay, Washington, from the State of...

Willapa Bay, Washington Benthic Habitats 1995 Substrate

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — In June 1995, the Columbia River Estuary Study Taskforce (CREST) acquired 295 true color aerial photographs (1:12,000) of Willapa Bay, Washington, from the State of...

LiDAR (Terrain), THURSTON COUNTY, WASHINGTON, USA

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — Fugro EarthData Company furnished the collection, processing, and development of LiDAR for 825 square miles in Washington (805 square miles of Thurston County and 20...

Advanced semi-active engine and transmission mounts: tools for modelling, analysis, design, and tuning

Science.gov (United States)

Farjoud, Alireza; Taylor, Russell; Schumann, Eric; Schlangen, Timothy

2014-02-01

This paper is focused on modelling, design, and testing of semi-active magneto-rheological (MR) engine and transmission mounts used in the automotive industry. The purpose is to develop a complete analysis, synthesis, design, and tuning tool that reduces the need for expensive and time-consuming laboratory and field tests. A detailed mathematical model of such devices is developed using multi-physics modelling techniques for physical systems with various energy domains. The model includes all major features of an MR mount including fluid dynamics, fluid track, elastic components, decoupler, rate-dip, gas-charged chamber, MR fluid rheology, magnetic circuit, electronic driver, and control algorithm. Conventional passive hydraulic mounts can also be studied using the same mathematical model. The model is validated using standard experimental procedures. It is used for design and parametric study of mounts; effects of various geometric and material parameters on dynamic response of mounts can be studied. Additionally, this model can be used to test various control strategies to obtain best vibration isolation performance by tuning control parameters. Another benefit of this work is that nonlinear interactions between sub-components of the mount can be observed and investigated. This is not possible by using simplified linear models currently available.

Vibration aging of diesel-engine mounted electrical equipment

International Nuclear Information System (INIS)

Lee, B.J.; Morton, W.C.

1994-01-01

The Emergency Diesel Generator (EDG) in a Nuclear Power Plant is considered to be a component which is essential to safe plant operation. Failures of auxiliary equipment directly mounted on the EDG creates costly repairs, and compromises the engine's availability and reliability. Although IEEE-323 requires addressing of safety-related components due to mechanically induced vibration, very few guidelines exist in the nuclear industry to show how this may be accounted for. Most engine vendors rely on the empirical experience data as the basis of their evaluation for vibration. Upgrade of engine controls, addition of monitoring devices and other engine modifications require design and installation of new equipment to be mounted directly on the engine. This necessitates the evaluation for engine-induced vibration which is considered to be one of the most severe design parameters. This paper discusses the engine vibration characteristics, and the acquisition of extensive field vibration data on the diesel engine under operating conditions. The data is then used to develop life cycle vibration qualification test profiles that can be applied with confidence in a laboratory environment to qualify engine-mounted equipment. The intent is to validate a product's ability to survive under worst case, extended service on-engine conditions. This paper describes the procedures and approaches used to achieve those goals, and provides developed profile examples and test results

Plate fixation in periprosthetic femur fractures Vancouver type B1-Trochanteric hook plate or subtrochanterical bicortical locking?

Science.gov (United States)

Lenz, Mark; Stoffel, Karl; Kielstein, Heike; Mayo, Keith; Hofmann, Gunther O; Gueorguiev, Boyko

2016-12-01

Proximal plate fixation in periprosthetic femur fractures can be improved by plate anchorage in the greater trochanter (lateral tension band principle) or bicortical locking screw placement beside the prosthesis stem in an embracement configuration. Both concepts were compared in a biomechanical test using a femoral hook plate (hook) or a locking attachment plate (LAP). After bone mineral density (BMD) measurement in the greater trochanter, six pairs of fresh frozen human femora were assigned to two groups and instrumented with cemented hip endoprostheses. A transverse osteotomy was set distal to the tip of the prosthesis, simulating a Vancouver B1 fracture. Each pair was instrumented using a plate tensioner with either hook or LAP construct. Cyclic testing (2Hz) with physiologic profile and monotonically increasing load was performed until catastrophic failure. Plate stiffness was compared in a four-point-bending-test. Paired student's-t-test was used for statistical evaluation (pTrochanteric fixation is highly BMD dependent and may be restricted to major greater trochanteric involvement requiring stabilization. Copyright © 2016 Elsevier Ltd. All rights reserved.

78 FR 17229 - Notice of Public Meeting, Eastern Washington Resource Advisory Council

Science.gov (United States)

2013-03-20

... DEPARTMENT OF THE INTERIOR Bureau of Land Management [LLORW00000 L102000000.ML0000 13XL1109AF.HAG13-0139] Notice of Public Meeting, Eastern Washington Resource Advisory Council AGENCY: Bureau of... the Eastern Washington Resource Advisory Council. The meeting on March 21, 2013, has been cancelled...

Improving Immunization Coverage in a Rural School District in Pierce County, Washington

Science.gov (United States)

Peterson, Robin M.; Cook, Carolyn; Yerxa, Mary E.; Marshall, James H.; Pulos, Elizabeth; Rollosson, Matthew P.

2012-01-01

Washington State has some of the highest percentages of school immunization exemptions in the country. We compared school immunization records in a rural school district in Pierce County, Washington, to immunization records in the state immunization information system (IIS) and parent-held records. Correcting school immunization records resulted…

Conceptual Design of Bottom-mounted Control Rod Drive Mechanism

International Nuclear Information System (INIS)

Lee, Jin Haeng; Kim, Sanghaun; Yoo, Yeonsik; Cho, Yeonggarp; Kim, Dongmin; Kim, Jong In

2013-01-01

The arrangement of the BMCRDMs and irradiation holes in the core is therefore easier than that of the top-mounted CRDM. Hence, many foreign research reactors, such as JRR-3M, JMTR, OPAL, and CARR, have adopted the BMCRDM concept. The purpose of this paper is to introduce the basic design concept on the BMCRDM. The major differences of the CRDMs between HANARO and KJRR are compared, and the design features and individual system of the BMCRDM for the KJRR are described. The Control Rod Drive Mechanism (CRDM) is a device to regulate the reactor power by changing the position of a Control Absorber Rod (CAR) and to shut down the reactor by fully inserting the CAR into the core within a specified time. The Bottom-Mounted CRDM (BMCRDM) for the KiJang Research Reactor (KJRR) is a quite different design concept compared to the top-mounted CRDM such as HANARO and JRTR. The main drive mechanism of the BMCRDM is located in a Reactivity Control Mechanism (RCM) room under the reactor pool bottom, which makes the interference with equipment in the reactor pool reduced

Conceptual Design of Bottom-mounted Control Rod Drive Mechanism

Energy Technology Data Exchange (ETDEWEB)

Lee, Jin Haeng; Kim, Sanghaun; Yoo, Yeonsik; Cho, Yeonggarp; Kim, Dongmin; Kim, Jong In [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-05-15

The arrangement of the BMCRDMs and irradiation holes in the core is therefore easier than that of the top-mounted CRDM. Hence, many foreign research reactors, such as JRR-3M, JMTR, OPAL, and CARR, have adopted the BMCRDM concept. The purpose of this paper is to introduce the basic design concept on the BMCRDM. The major differences of the CRDMs between HANARO and KJRR are compared, and the design features and individual system of the BMCRDM for the KJRR are described. The Control Rod Drive Mechanism (CRDM) is a device to regulate the reactor power by changing the position of a Control Absorber Rod (CAR) and to shut down the reactor by fully inserting the CAR into the core within a specified time. The Bottom-Mounted CRDM (BMCRDM) for the KiJang Research Reactor (KJRR) is a quite different design concept compared to the top-mounted CRDM such as HANARO and JRTR. The main drive mechanism of the BMCRDM is located in a Reactivity Control Mechanism (RCM) room under the reactor pool bottom, which makes the interference with equipment in the reactor pool reduced.

On-field mounting position estimation of a lidar sensor

Science.gov (United States)

Khan, Owes; Bergelt, René; Hardt, Wolfram

2017-10-01

In order to retrieve a highly accurate view of their environment, autonomous cars are often equipped with LiDAR sensors. These sensors deliver a three dimensional point cloud in their own co-ordinate frame, where the origin is the sensor itself. However, the common co-ordinate system required by HAD (Highly Autonomous Driving) software systems has its origin at the center of the vehicle's rear axle. Thus, a transformation of the acquired point clouds to car co-ordinates is necessary, and thereby the determination of the exact mounting position of the LiDAR system in car coordinates is required. Unfortunately, directly measuring this position is a time-consuming and error-prone task. Therefore, different approaches have been suggested for its estimation which mostly require an exhaustive test-setup and are again time-consuming to prepare. When preparing a high number of LiDAR mounted test vehicles for data acquisition, most approaches fall short due to time or money constraints. In this paper we propose an approach for mounting position estimation which features an easy execution and setup, thus making it feasible for on-field calibration.

Multilayer mounting for long-term light sheet microscopy of zebrafish.

Science.gov (United States)

Weber, Michael; Mickoleit, Michaela; Huisken, Jan

2014-02-27

Light sheet microscopy is the ideal imaging technique to study zebrafish embryonic development. Due to minimal photo-toxicity and bleaching, it is particularly suited for long-term time-lapse imaging over many hours up to several days. However, an appropriate sample mounting strategy is needed that offers both confinement and normal development of the sample. Multilayer mounting, a new embedding technique using low-concentration agarose in optically clear tubes, now overcomes this limitation and unleashes the full potential of light sheet microscopy for real-time developmental biology.

Development of a helmet-mounted PLZT thermal/flash protection system

International Nuclear Information System (INIS)

Harris, J.O. Jr.; Cutchen, J.T.; Pfoff, B.J.

1976-01-01

Sandia Laboratories is developing PLZT thermal/flash protective devices (TFPD's) goggles to prevent exposure and resultant eye damage from nuclear weapon detonations. The primary emphasis of the present program is to transfer technology and establish production capability for helmet-mounted PLZT/TFPD goggles for USAF flight crews, with a non-helmet-mounted configuration to follow. The first production units are anticipated in the fall of 1977. The operating principles of the PLZT/TFPD goggle device are briefly outlined, and the device configuration and operational characteristics are described

76 FR 58031 - Notice of Intent To Repatriate Cultural Items: Thomas Burke Memorial Washington State Museum...

Science.gov (United States)

2011-09-19

... DEPARTMENT OF THE INTERIOR National Park Service [2253-665] Notice of Intent To Repatriate Cultural Items: Thomas Burke Memorial Washington State Museum, University of Washington, Seattle, WA AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The Thomas Burke Memorial Washington State Museum...

Creating Gaze Annotations in Head Mounted Displays

DEFF Research Database (Denmark)

Mardanbeigi, Diako; Qvarfordt, Pernilla

2015-01-01

To facilitate distributed communication in mobile settings, we developed GazeNote for creating and sharing gaze annotations in head mounted displays (HMDs). With gaze annotations it possible to point out objects of interest within an image and add a verbal description. To create an annota- tion...

Solidly Mounted Resonator with Optimized Acoustic Reflector

NARCIS (Netherlands)

Jose, Sumy; Jansman, Andreas; Hueting, Raymond Josephus Engelbart

2009-01-01

The quality factor (Q) of the Solidly Mounted Resonator is limited by acoustic losses caused by waves leaking through the mirror stack. Traditionally employed acoustic mirror reflects only longitudinal waves and not shear waves. Starting with the stop-band theory and the principle of spacer layers

El Consenso de Washington: aciertos, yerros y omisiones

Directory of Open Access Journals (Sweden)

Juan Carlos Moreno-Brid

2004-12-01

Full Text Available This paper analyses the economic and social development of Latin America after nearly two decades of macroeconomic policies and reforms in line with the “Washington Consensus”. It shows that these policies did lower inflation and induced an export boom, but failed to boost domestic investment and to remove the balance of payments binding constraint on the region’s long–term path of economic expansion. Four alternative explanations of such poor performance of the Washington Consensus are compared. It is argued, in particular, that, contrary to mainstream opinion, in Latin America there is no clear association between the depth of macroeconomic reforms and economic growth performance.

Changes in seismic velocity during the first 14 months of the 2004–2008 eruption of Mount St. Helens, Washington

Science.gov (United States)

Hotovec-Ellis, A.J.; Vidale, J.E.; Gomberg, Joan S.; Thelen, Weston A.; Moran, Seth C.

2015-01-01

Mount St. Helens began erupting in late 2004 following an 18 year quiescence. Swarms of repeating earthquakes accompanied the extrusion of a mostly solid dacite dome over the next 4 years. In some cases the waveforms from these earthquakes evolved slowly, likely reflecting changes in the properties of the volcano that affect seismic wave propagation. We use coda-wave interferometry to quantify small changes in seismic velocity structure (usually <1%) between two similar earthquakes and employed waveforms from several hundred families of repeating earthquakes together to create a continuous function of velocity change observed at permanent stations operated within 20 km of the volcano. The high rate of earthquakes allowed tracking of velocity changes on an hourly time scale. Changes in velocity were largest near the newly extruding dome and likely related to shallow deformation as magma first worked its way to the surface. We found strong correlation between velocity changes and the inverse of real-time seismic amplitude measurements during the first 3 weeks of activity, suggesting that fluctuations of pressure in the shallow subsurface may have driven both seismicity and velocity changes. Velocity changes during the remainder of the eruption likely result from a complex interplay of multiple effects and are not well explained by any single factor alone, highlighting the need for complementary geophysical data when interpreting velocity changes.

Self-similar rupture implied by scaling properties of volcanic earthquakes occurring during the 2004-2008 eruption of Mount St. Helens, Washington

Science.gov (United States)

Harrington, Rebecca M.; Kwiatek, Grzegorz; Moran, Seth C.

2015-01-01

We analyze a group of 6073 low-frequency earthquakes recorded during a week-long temporary deployment of broadband seismometers at distances of less than 3 km from the crater at Mount St. Helens in September of 2006. We estimate the seismic moment (M0) and spectral corner frequency (f0) using a spectral ratio approach for events with a high signal-to-noise (SNR) ratio that have a cross-correlation coefficient of 0.8 or greater with at least five other events. A cluster analysis of cross-correlation values indicates that the group of 421 events meeting the SNR and cross-correlation criteria forms eight event families that exhibit largely self-similar scaling. We estimate the M0 and f0 values of the 421 events and calculate their static stress drop and scaled energy (ER/M0) values. The estimated values suggest self-similar scaling within families, as well as between five of eight families (i.e.,  and  constant). We speculate that differences in scaled energy values for the two families with variable scaling may result from a lack of resolution in the velocity model. The observation of self-similar scaling is the first of its kind for such a large group of low-frequency volcanic tectonic events occurring during a single active dome extrusion eruption.

Doctors of Osteopathy Licensed in Washington.

Science.gov (United States)

Senters, Jo

Based on information gathered by the Health Manpower Project through a survey cosponsored with the Washington Osteopathic Medical Association, this report begins with a statement of philosophy of osteopathic medicine and proceeds to comment on where such professional education is available. Remarks on the type of educational background of the…

Changing Housing Patterns in Metropolitan Washington

Science.gov (United States)

Grier, George; Grier, Eunice

1975-01-01

This testimony, before a public hearing of the New York City Commission on Human Rights in May 1974, summarizes extensive studies of changing minority residential patterns in metropolitan Washington and less extensive studies of other groups; the prospects for future desegregation and for using the growing economic potential of minority families…

Timber resource statistics for western Washington.

Science.gov (United States)

Coffin D. MacLean; Patricia M. Bassett; Glenn. Yeary

1992-01-01

This report summarizes a 1988-90 timber resource inventory of 19 counties in western Washington: Clallam, Clark, Cowlitz, Grays Harbor, Island, Jefferson, King, Kitsap, Lewis, Mason, Pacific, Pierce, San Juan, Skagit, Skamania, Snohomish, Thurston, Wahkiakum, and Whatcom. Detailed tables of forest area, timber volume, growth, mortality, and harvest are presented.

78 FR 53235 - 50th Anniversary of the March on Washington for Jobs and Freedom

Science.gov (United States)

2013-08-28

... Anniversary of the March on Washington for Jobs and Freedom By the President of the United States of America A... waters of the reflecting pool, to the proud base of the Washington Monument. They were men and women..., and justice for all. The March on Washington capped off a summer of discontent, a time when the...

Beating-heart registration for organ-mounted robots.

Science.gov (United States)

Wood, Nathan A; Schwartzman, David; Passineau, Michael J; Moraca, Robert J; Zenati, Marco A; Riviere, Cameron N

2018-03-06

Organ-mounted robots address the problem of beating-heart surgery by adhering to the heart, passively providing a platform that approaches zero relative motion. Because of the quasi-periodic deformation of the heart due to heartbeat and respiration, registration must address not only spatial registration but also temporal registration. Motion data were collected in the porcine model in vivo (N = 6). Fourier series models of heart motion were developed. By comparing registrations generated using an iterative closest-point approach at different phases of respiration, the phase corresponding to minimum registration distance is identified. The spatiotemporal registration technique presented here reduces registration error by an average of 4.2 mm over the 6 trials, in comparison with a more simplistic static registration that merely averages out the physiological motion. An empirical metric for spatiotemporal registration of organ-mounted robots is defined and demonstrated using data from animal models in vivo. Copyright © 2018 John Wiley & Sons, Ltd.

Mismatched racial identities, colourism, and health in Toronto and Vancouver.

Science.gov (United States)

Veenstra, Gerry

2011-10-01

Using original telephone survey data collected from adult residents of Toronto (n = 685) and Vancouver (n = 814) in 2009, I investigate associations between mental and physical health and variously conceived racial identities. An 'expressed racial identity' is a self-identification with a racial grouping that a person will readily express to others when asked to fit into official racial classifications presented by Census forms, survey researchers, insurance forms, and the like. Distinguishing between Asian, Black, South Asian, and White expressed racial identities, I find that survey respondents expressing Black identity are the most likely to report high blood pressure or hypertension, a risk that is slightly attenuated by socioeconomic status, and that respondents expressing Asian identity are the most likely to report poorer self-rated mental health and self-rated overall health, risks that are not explained by socioeconomic status. I also find that darker-skinned Black respondents are more likely than lighter-skinned Black respondents to report poor health outcomes, indicating that colourism, processes of discrimination which privilege lighter-skinned people of colour over their darker-skinned counterparts, exists and has implications for well-being in Canada as it does in the United States. Finally, 'reflected racial identity' refers to the racial identity that a person believes that others tend to perceive him or her to be. I find that expressed and reflected racial identities differ from one another for large proportions of self-expressed Black and South Asian respondents and relatively few self-expressed White and Asian respondents. I also find that mismatched racial identities correspond with relatively high risks of various poor health outcomes, especially for respondents who consider themselves White but believe that others tend to think they are something else. I conclude by presenting a framework for conceptualizing multifaceted suites of racial

A Grape Production Guide for Vocational Agriculture Instructors in Washington. Final Report.

Science.gov (United States)

Padelford, Stewart L.; Cvancara, Joseph G., Ed.

This curriculum guide is intended to provide vocational agriculture instructors with an up-to-date resource dealing with grape production in Washington. Addressed in the individual units of the guide are the following topics: the history of grape production; grape types important to Washington; site selection for a vineyard; establishment and…

Instrument-mounted displays for reducing cognitive load during surgical navigation.

Science.gov (United States)

Herrlich, Marc; Tavakol, Parnian; Black, David; Wenig, Dirk; Rieder, Christian; Malaka, Rainer; Kikinis, Ron

2017-09-01

Surgical navigation systems rely on a monitor placed in the operating room to relay information. Optimal monitor placement can be challenging in crowded rooms, and it is often not possible to place the monitor directly beside the situs. The operator must split attention between the navigation system and the situs. We present an approach for needle-based interventions to provide navigational feedback directly on the instrument and close to the situs by mounting a small display onto the needle. By mounting a small and lightweight smartwatch display directly onto the instrument, we are able to provide navigational guidance close to the situs and directly in the operator's field of view, thereby reducing the need to switch the focus of view between the situs and the navigation system. We devise a specific variant of the established crosshair metaphor suitable for the very limited screen space. We conduct an empirical user study comparing our approach to using a monitor and a combination of both. Results from the empirical user study show significant benefits for cognitive load, user preference, and general usability for the instrument-mounted display, while achieving the same level of performance in terms of time and accuracy compared to using a monitor. We successfully demonstrate the feasibility of our approach and potential benefits. With ongoing technological advancements, instrument-mounted displays might complement standard monitor setups for surgical navigation in order to lower cognitive demands and for improved usability of such systems.

Evaluation of shear mounted elastomeric damper

Science.gov (United States)

Zorzi, E.; Walton, J.

1982-01-01

Viton-70 elastomeric shear mounted damper was built and tested on a T-55 power turbine spool in the rotor's high speed balancing rig. This application of a shear mounted elastomeric damper demonstrated for the first time, the feasibility of using elastomers as the primary rotor damping source in production turbine engine hardware. The shear damper design was selected because it was compatible with actual gas turbine engine radial space constraints, could accommodate both the radial and axial thrust loads present in gas turbine engines, and was capable of controlled axial preload. The shear damper was interchangeable with the production T-55 power turbine roller bearing support so that a direct comparison between the shear damper and the production support structure could be made. Test results show that the Viton-70 elastomer damper operated successfully and provided excellent control of both synchronous and nonsynchronous vibrations through all phases of testing up to the maximum rotor speed of 16,000 rpm. Excellent correlation between the predicted and experienced critical speeds, mode shapes and log decrements for the power turbine rotor and elastomer damper assembly was also achieved.

Evaluation of wind flow with a nacelle-mounted, continuous wave wind lidar

DEFF Research Database (Denmark)

Medley, John; Barker, Will; Harris, Mike

2014-01-01

Nacelle-mounted lidar is becoming widely recognized as a tool with potential for assessing power curves, understanding wind flow characteristics, and controlling turbines. As rotor diameters continue to increase, and the deployment of turbines in complex terrain becomes more widespread, knowledge...... mounted on the nacelle of a 550 kW turbine at the Risø campus of the Technical University of Denmark (DTU). Lidar measurements of wind speed and turbulence were compared against those made by anemometers on a high-quality traditional mast. Analysis showed excellent correlation between mast and Zeph...... that this is the first time that a commercially available nacelle-mounted lidar has been used to evaluate such rotor-equivalent power curves....

Medicinal Cannabis: A Survey Among Health Care Providers in Washington State

Science.gov (United States)

Carlini, Beatriz H; Garrett, Sharon B; Carter, Gregory T

2017-02-01

Washington State allows marijuana use for medical (since 1998) and recreational (since 2012) purposes. The benefits of medicinal cannabis (MC) can be maximized if clinicians educate patients about dosing, routes of administration, side effects, and plant composition. However, little is known about clinicians' knowledge and practices in Washington State. An anonymous online survey assessed providers' MC knowledge, beliefs, clinical practices, and training needs. The survey was disseminated through health care providers' professional organizations in Washington State. Descriptive analysis compared providers who had and had not authorized MC for patients. Survey results informed the approach and content of an online training on best clinical practices of MC. Four hundred ninety-four health care providers responded to the survey. Approximately two-third were women, aged 30 to 60 years, and working in family or internal medicine. More than half of the respondents were legally allowed to write MC authorizations per Washington State law, and 27% of those had issued written MC authorizations. Overall, respondents reported low knowledge and comfort level related to recommending MC. Respondents rated MC knowledge as important and supported inclusion of MC training in medical/health provider curriculum. Most Washington State providers have not received education on scientific basis of MC or training on best clinical practices of MC. Clinicians who had issued MC authorizations were more likely to have received MC training than those who had not issued MC authorization. The potential of MCs to benefit some patients is hindered by the lack of comfort of clinicians to recommend it. Training opportunities are badly needed to address these issues.

National Nuclear Waste Policy Act of 1981. Hearings before the Committee on Environment and Public Works, United States Senate, Ninety-Seventh Congress, First Session on S. 1662, October 31, 1981, Richland, Washington; November 9, 1981, Washington, DC

International Nuclear Information System (INIS)

Anon.

1982-01-01

Hearings were held on October 31, 1981 in Richland, Washington and on November 9, 1981 in Washington, DC to discuss the effort in S. 1662 to establish a national policy and an environmentally acceptable program for managing nuclear wastes from domestic commercial activities. The Richland hearing was held in recognition that Washington State will bear the major impact of the legislation. Witnesses at the Washington, DC hearing included officials from states that are potential sites for radioactive waste storage and disposal facilities. The hearing record includes the testimony of 16 witnesses in Richland and seven in Washington, DC, followed by a reprint of S. 1662 and additional material submitted for the record

Costs of mounting an immune response during pregnancy in a lizard.

Science.gov (United States)

Meylan, Sandrine; Richard, Murielle; Bauer, Sophie; Haussy, Claudy; Miles, Donald

2013-01-01

Immune defenses are of great benefit to hosts, but reducing the impact of infection by mounting an immune response also entails costs. However, the physiological mechanisms that generate the costs of an immune response remain poorly understood. Moreover, the majority of studies investigating the consequences of an immune challenge in vertebrates have been conducted on mammals and birds. The aim of this study is to investigate the physiological costs of mounting an immune response during gestation in an ectothermic species. Indeed, because ectothermic species are unable to internally regulate their body temperature, the apportionment of resources to homeostatic activities in ectothermic species can differ from that in endothermic species. We conducted this study on the common lizard Zootoca vivipara. We investigated the costs of mounting an immune response by injecting females with sheep red blood cells and quantified the consequences to reproductive performance (litter mass and success) and physiological performance (standard metabolic rate, endurance, and phytohemagglutinin response). In addition, we measured basking behavior. Our analyses revealed that mounting an immune response affected litter mass, physiological performance, and basking behavior. Moreover, we demonstrated that the modulation of an immune challenge is impacted by intrinsic factors, such as body size and condition.

A new magnetorheological fluid–elastomer mount: phenomenological modeling and experimental study

International Nuclear Information System (INIS)

Wang, Xiaojie; Gordaninejad, Faramarz

2009-01-01

A new magnetorheological (MR) mount consisting of an MR fluid encapsulated in a polymeric solid is presented. The mechanical properties of the proposed mount are controllable through an externally applied magnetic field. The dynamic behavior of this system under various magnetic fields has been investigated by means of oscillatory compression cycles over a frequency range of 0.1–10 Hz for various deformations (less than 1 mm). The energy dissipation in the material is analyzed as related to strain amplitude, strain frequency and magnetic field strength. The field induced damping mechanism is discussed in terms of the damping exponent. A phenomenological model is presented to account for the dynamic behavior of the MR fluid–elastomer mount's vibration isolators under oscillatory compressive deformations. This model is a two-element system comprised of a variable friction damper and a nonlinear spring. The parameters of the model have been identified by a series of harmonic loading tests. The theoretical and experimental results are in excellent agreement. Both experimental and theoretical results have demonstrated that the proposed MR fluid–elastomer mounts show promise in applications where tuning vibration characteristics of a system are desired, such as altering natural frequencies, mode shapes, and damping properties

Assessment of Energy Removal Impacts on Physical Systems: Hydrodynamic Model Domain Expansion and Refinement, and Online Dissemination of Model Results

International Nuclear Information System (INIS)

Yang, Zhaoqing; Khangaonkar, Tarang; Wang, Taiping

2010-01-01

In this report we describe the (1) the expansion of the PNNL hydrodynamic model domain to include the continental shelf along the coasts of Washington, Oregon, and Vancouver Island; and (2) the approach and progress in developing the online/Internet disseminations of model results and outreach efforts in support of the Puget Sound Operational Forecast System (PS-OPF). Submittal of this report completes the work on Task 2.1.2, Effects of Physical Systems, Subtask 2.1.2.1, Hydrodynamics, for fiscal year 2010 of the Environmental Effects of Marine and Hydrokinetic Energy project.

Mechanical Design of an Omni-Directional Sensor Mount

National Research Council Canada - National Science Library

Rosheim, Mark

2002-01-01

This effort has been directed to development and demonstration of a gimbal mount capable of 180 degree singularity- free pitch and yaw motion about a two-axis center, avoiding the common problem of gimbal lock...

Mounting and Alignment of Full-Shell Replicated X-Ray Optics

Science.gov (United States)

Gubarev, Mikhail; Arnold, William; Kester, Thomas; Ramsey, Brian; Smithers, Martin

2007-01-01

We are developing grazing-incidence x-ray optics for astronomy. The optics are full-cylinder mirror shells fabricated using electroformed-nickel replication off super-polished mandrels. For space-based applications where weight is at a premium, very-thin-walled, light-weight mirrors are required. Such shells have been fabricated at MSFC with greater than 15 arcsec resolution. The challenge, however, is to preserve this resolution during mounting and assembly. We present here a status report on a mounting and alignment system currently under development at Marshall Space Flight Center to meet this challenge.

An Experimental Study of a Sting-Mounted Circulation Control Wing

Science.gov (United States)

1991-12-01

atmospheric pressure was read from a Henry J. Green ML-330/FM mercury barometer and the desired tunnel q was determined from: q.)= 1/2 RTatms (21) F atmos C2...attachment to the Coanda surface. With the model mounted on a bench outside the tunnel, a fixture was attached to the model so that a pitot tube could be...mounted immediately aft of the blowing slot to measure jet total pressure at any point along the trailing edge. The pitot tube was connected to a 50 inch

Experimental study of some mounting brackets to support fuel elements

International Nuclear Information System (INIS)

Aubert, M.; Poglia, S.; Roche, R.

1958-09-01

In an atomic pile with vertical channels, fuel elements are stacked on one another. According to a possible assembly, fuel element can be contained by a graphite sleeve and be supported by a mounting bracket in this sleeve. Sleeves are then stacked on one another. The authors report the investigation of different designs for these mounting brackets. They describe their mechanical role and their mechanical, aerodynamic, neutronic and test conditions. They report tests performed on brackets made in graphite and on brackets made in stainless steel and graphite, and discuss the obtained results

Mount Sinai Hospital's approach to Ontario's Health System Funding Reform.

Science.gov (United States)

Chalk, Tyler; Lau, Davina; Morgan, Matthew; Dietrich, Sandra; Beduz, Mary Agnes; Bell, Chaim M

2014-01-01

In April 2012, the Ontario government introduced Health System Funding Reform (HSFR), a transformational shift in how hospitals are funded. Mount Sinai Hospital recognized that moving from global funding to a "patient-based" model would have substantial operational and clinical implications. Adjusting to the new funding environment was set as a top corporate priority, serving as the strategic basis for re-examining and redesigning operations to further improve both quality and efficiency. Two years into HSFR, this article outlines Mount Sinai Hospital's approach and highlights key lessons learned. Copyright © 2014 Longwoods Publishing.

Optimal design of high damping force engine mount featuring MR valve structure with both annular and radial flow paths

International Nuclear Information System (INIS)

Nguyen, Q H; Choi, S B; Lee, Y S; Han, M S

2013-01-01

This paper focuses on the optimal design of a compact and high damping force engine mount featuring magnetorheological fluid (MRF). In the mount, a MR valve structure with both annular and radial flows is employed to generate a high damping force. First, the configuration and working principle of the proposed MR mount is introduced. The MRF flows in the mount are then analyzed and the governing equations of the MR mount are derived based on the Bingham plastic behavior of the MRF. An optimal design of the MR mount is then performed to find the optimal structure of the MR valve to generate a maximum damping force with certain design constraints. In addition, the gap size of MRF ducts is empirically chosen considering the ‘lockup’ problem of the mount at high frequency. Performance of the optimized MR mount is then evaluated based on finite element analysis and discussions on performance results of the optimized MR mount are given. The effectiveness of the proposed MR engine mount is demonstrated via computer simulation by presenting damping force and power consumption. (paper)

Optimal design of high damping force engine mount featuring MR valve structure with both annular and radial flow paths

Science.gov (United States)

Nguyen, Q. H.; Choi, S. B.; Lee, Y. S.; Han, M. S.

2013-11-01

This paper focuses on the optimal design of a compact and high damping force engine mount featuring magnetorheological fluid (MRF). In the mount, a MR valve structure with both annular and radial flows is employed to generate a high damping force. First, the configuration and working principle of the proposed MR mount is introduced. The MRF flows in the mount are then analyzed and the governing equations of the MR mount are derived based on the Bingham plastic behavior of the MRF. An optimal design of the MR mount is then performed to find the optimal structure of the MR valve to generate a maximum damping force with certain design constraints. In addition, the gap size of MRF ducts is empirically chosen considering the ‘lockup’ problem of the mount at high frequency. Performance of the optimized MR mount is then evaluated based on finite element analysis and discussions on performance results of the optimized MR mount are given. The effectiveness of the proposed MR engine mount is demonstrated via computer simulation by presenting damping force and power consumption.

Washington Irving and the American Indian.

Science.gov (United States)

Littlefield, Daniel F., Jr.

1979-01-01

Some modern scholars feel that Washington Irving vacillated between romanticism and realism in his literary treatment of the American Indian. However, a study of all his works dealing with Indians, placed in context with his non-Indian works, reveals that his attitude towards Indians was intelligent and enlightened for his time. (CM)

An Experimental High-Resolution Forecast System During the Vancouver 2010 Winter Olympic and Paralympic Games

Science.gov (United States)

Mailhot, J.; Milbrandt, J. A.; Giguère, A.; McTaggart-Cowan, R.; Erfani, A.; Denis, B.; Glazer, A.; Vallée, M.

2014-01-01

Environment Canada ran an experimental numerical weather prediction (NWP) system during the Vancouver 2010 Winter Olympic and Paralympic Games, consisting of nested high-resolution (down to 1-km horizontal grid-spacing) configurations of the GEM-LAM model, with improved geophysical fields, cloud microphysics and radiative transfer schemes, and several new diagnostic products such as density of falling snow, visibility, and peak wind gust strength. The performance of this experimental NWP system has been evaluated in these winter conditions over complex terrain using the enhanced mesoscale observing network in place during the Olympics. As compared to the forecasts from the operational regional 15-km GEM model, objective verification generally indicated significant added value of the higher-resolution models for near-surface meteorological variables (wind speed, air temperature, and dewpoint temperature) with the 1-km model providing the best forecast accuracy. Appreciable errors were noted in all models for the forecasts of wind direction and humidity near the surface. Subjective assessment of several cases also indicated that the experimental Olympic system was skillful at forecasting meteorological phenomena at high-resolution, both spatially and temporally, and provided enhanced guidance to the Olympic forecasters in terms of better timing of precipitation phase change, squall line passage, wind flow channeling, and visibility reduction due to fog and snow.

76 FR 2370 - Mount Storm Hydro, LLC; Notice of Preliminary Permit Application Accepted for Filing and...

Science.gov (United States)

2011-01-13

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Project No. 13863-000] Mount Storm..., Motions To Intervene, and Competing Applications January 6, 2011. On October 14, 2010, Mount Storm Hydro... (FPA), proposing to study the feasibility of the Mount Storm Pumped Storage Project to be located near...

A vehicle mounted scintillation ratemeter for environmental survey

International Nuclear Information System (INIS)

Cavell, I.W.

1960-01-01

An improved method of mounting an existing environmental gamma survey equipment in a vehicle is described. Performance data for the equipment is given and some typical radiometric traces obtained at A.E.E. Winfrith given. (author)

How Mount Stromlo Observatory shed its imperial beginnings

Science.gov (United States)

Bhathal, Ragbir

2014-12-01

In the 90 years since its foundation in 1924, Mount Stromlo Observatory in Australia has changed from an outpost of empire to an international research institution. Ragbir Bhathal examines how the British influence waxed and waned.

Report : public transportation in Washington State, 1984

Science.gov (United States)

1984-10-01

This report is an update of the Public Transportation in Washington State publication, dated December 1981. In order to reflect the changes that have occurred since that time, this report contains the most current data obtainable. Chapter One of this...

Scientific Framework for Stormwater Monitoring by the Washington State Department of Transportation

Science.gov (United States)

Sheibley, R.W.; Kelly, V.J.; Wagner, R.J.

2009-01-01

The Washington State Department of Transportation municipal stormwater monitoring program, in operation for about 8 years, never has received an external, objective assessment. In addition, the Washington State Department of Transportation would like to identify the standard operating procedures and quality assurance protocols that must be adopted so that their monitoring program will meet the requirements of the new National Pollutant Discharge Elimination System municipal stormwater permit. As a result, in March 2009, the Washington State Department of Transportation asked the U.S. Geological Survey to assess their pre-2009 municipal stormwater monitoring program. This report presents guidelines developed for the Washington State Department of Transportation to meet new permit requirements and regional/national stormwater monitoring standards to ensure that adequate processes and procedures are identified to collect high-quality, scientifically defensible municipal stormwater monitoring data. These include: (1) development of coherent vision and cooperation among all elements of the program; (2) a comprehensive approach for site selection; (3) an effective quality assurance program for field, laboratory, and data management; and (4) an adequate database and data management system.

The research on a novel type of the solar-blind UV head-mounted displays

Science.gov (United States)

Zhao, Shun-long

2011-08-01

Ultraviolet technology of detecting is playing a more and more important role in the field of civil application, especially in the corona discharge detection, in modern society. Now the UV imaging detector is one of the most important equipments in power equipment flaws detection. And the modern head-mounted displays (HMDs) have shown the applications in the fields of military, industry production, medical treatment, entertainment, 3D visualization, education and training. We applied the system of head-mounted displays to the UV image detection, and a novel type of head-mounted displays is presented: the solar-blind UV head-mounted displays. And the structure is given. By the solar-blind UV head-mounted displays, a real-time, isometric and visible image of the corona discharge is correctly displayed upon the background scene where it exists. The user will see the visible image of the corona discharge on the real scene rather than on a small screen. Then the user can easily find out the power equipment flaws and repair them. Compared with the traditional UV imaging detector, the introducing of the HMDs simplifies the structure of the whole system. The original visible spectrum optical system is replaced by the eye in the solar-blind UV head-mounted displays. And the optical image fusion technology would be used rather than the digital image fusion system which is necessary in traditional UV imaging detector. That means the visible spectrum optical system and digital image fusion system are not necessary. This makes the whole system cheaper than the traditional UV imaging detector. Another advantage of the solar-blind UV head-mounted displays is that the two hands of user will be free. So while observing the corona discharge the user can do some things about it. Therefore the solar-blind UV head-mounted displays can make the corona discharge expose itself to the user in a better way, and it will play an important role in corona detection in the future.

Quantification of marine macro-debris abundance around Vancouver Island, Canada, based on archived aerial photographs processed by projective transformation.

Science.gov (United States)

Kataoka, Tomoya; Murray, Cathryn Clarke; Isobe, Atsuhiko

2017-09-12

The abundance of marine macro-debris was quantified with high spatial resolution by applying an image processing technique to archived shoreline aerial photographs taken over Vancouver Island, Canada. The photographs taken from an airplane at oblique angles were processed by projective transformation for georeferencing, where five reference points were defined by comparing aerial photographs with satellite images of Google Earth. Thereafter, pixels of marine debris were extracted based on their color differences from the background beaches. The debris abundance can be evaluated by the ratio of an area covered by marine debris to that of the beach (percent cover). The horizontal distribution of percent cover of marine debris was successfully computed from 167 aerial photographs and was significantly related to offshore Ekman flows and winds (leeway drift and Stokes drift). Therefore, the estimated percent cover is useful information to determine priority sites for mitigating adverse impacts across broad areas. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tackling the challenges of fully immersive head-mounted AR devices

Science.gov (United States)

Singer, Wolfgang; Hillenbrand, Matthias; Münz, Holger

2017-11-01

The optical requirements of fully immersive head mounted AR devices are inherently determined by the human visual system. The etendue of the visual system is large. As a consequence, the requirements for fully immersive head-mounted AR devices exceeds almost any high end optical system. Two promising solutions to achieve the large etendue and their challenges are discussed. Head-mounted augmented reality devices have been developed for decades - mostly for application within aircrafts and in combination with a heavy and bulky helmet. The established head-up displays for applications within automotive vehicles typically utilize similar techniques. Recently, there is the vision of eyeglasses with included augmentation, offering a large field of view, and being unobtrusively all-day wearable. There seems to be no simple solution to reach the functional performance requirements. Known technical solutions paths seem to be a dead-end, and some seem to offer promising perspectives, however with severe limitations. As an alternative, unobtrusively all-day wearable devices with a significantly smaller field of view are already possible.

The Observatory as Laboratory: Spectral Analysis at Mount Wilson Observatory

Science.gov (United States)

Brashear, Ronald

2018-01-01

This paper will discuss the seminal changes in astronomical research practices made at the Mount Wilson Observatory in the early twentieth century by George Ellery Hale and his staff. Hale’s desire to set the agenda for solar and stellar astronomical research is often described in terms of his new telescopes, primarily the solar tower observatories and the 60- and 100-inch telescopes on Mount Wilson. This paper will focus more on the ancillary but no less critical parts of Hale’s research mission: the establishment of associated “physical” laboratories as part of the observatory complex where observational spectral data could be quickly compared with spectra obtained using specialized laboratory equipment. Hale built a spectroscopic laboratory on the mountain and a more elaborate physical laboratory in Pasadena and staffed it with highly trained physicists, not classically trained astronomers. The success of Hale’s vision for an astronomical observatory quickly made the Carnegie Institution’s Mount Wilson Observatory one of the most important astrophysical research centers in the world.

Mounting of Biomaterials for Use in Ophthalmic Cell Therapies.

Science.gov (United States)

Harkin, Damien G; Dunphy, Siobhan E; Shadforth, Audra M A; Dawson, Rebecca A; Walshe, Jennifer; Zakaria, Nadia

2017-11-01

When used as scaffolds for cell therapies, biomaterials often present basic handling and logistical problems for scientists and surgeons alike. The quest for an appropriate mounting device for biomaterials is therefore a significant and common problem. In this review, we provide a detailed overview of the factors to consider when choosing an appropriate mounting device including those experienced during cell culture, quality assurance, and surgery. By way of example, we draw upon our combined experience in developing epithelial cell therapies for the treatment of eye diseases. We discuss commercially available options for achieving required goals and provide a detailed analysis of 4 experimental designs developed within our respective laboratories in Australia, the United Kingdom, and Belgium.

Siting study for small platform-mounted industrial energy reactors

International Nuclear Information System (INIS)

1975-07-01

Utilizing an existing 313 MW(t) ship propulsion reactor design, a concept has been formulated for a floating platform-mounted nuclear plant and an evaluation has been made to determine reductions in construction time and cost achievable by repetitive platform construction in a shipyard. Concepts and estimates are presented for siting platform-mounted nuclear plants at the location of industrial facilities where the nuclear plants would furnish industrial process heat and/or electrical power. The representative industrial site designated for this study is considered typical of sites that might be used along the extensive network of navigable canals adjacent to the ocean and is similar to potential sites along the inland waterways of the United States

A concept of active mount for space applications

Science.gov (United States)

Souleille, A.; Lampert, T.; Lafarga, V.; Hellegouarch, S.; Rondineau, A.; Rodrigues, G.; Collette, C.

2018-06-01

Sensitive payloads mounted on top of launchers are subjected to many sources of disturbances during the flight. The most severe dynamic loads arise from the ignition of the motors, gusts, pressure fluctuations in the booster and from the separation of the boosters. The transmission of these dynamic forces can be reduced by mounting payloads on passive isolators, which comes at the expense of harmful amplifications of the motion at low frequency due to suspension resonances. To bypass this shortcoming, this paper presents a novel concept of active mount for aerospace payloads, which is easy to install, and meets two objectives. The first one is a high damping authority on both suspension resonances and flexible resonances without compromising the isolation and large stability margins of the closed loop system due to the collocation of the actuator and the sensor. The second one is a broadband reduction of the dynamic force transmitted to the payload, which was achieved in terms of 16 dB. The concept is presented in the first part of the paper and studied numerically and experimentally on a single degree of freedom isolator. A commercial isolator has been chosen for the purpose of the demonstration. The second part of the paper is dedicated to experimental validations on multi-degree of freedom scaled test benches. It is shown that the force feedback allows damping of both suspension and flexible modes (first and second modes, respectively), and significantly reducing the force transmitted in some broad frequency ranges.

A concept of active mount for space applications

Science.gov (United States)

Souleille, A.; Lampert, T.; Lafarga, V.; Hellegouarch, S.; Rondineau, A.; Rodrigues, G.; Collette, C.

2017-10-01

Sensitive payloads mounted on top of launchers are subjected to many sources of disturbances during the flight. The most severe dynamic loads arise from the ignition of the motors, gusts, pressure fluctuations in the booster and from the separation of the boosters. The transmission of these dynamic forces can be reduced by mounting payloads on passive isolators, which comes at the expense of harmful amplifications of the motion at low frequency due to suspension resonances. To bypass this shortcoming, this paper presents a novel concept of active mount for aerospace payloads, which is easy to install, and meets two objectives. The first one is a high damping authority on both suspension resonances and flexible resonances without compromising the isolation and large stability margins of the closed loop system due to the collocation of the actuator and the sensor. The second one is a broadband reduction of the dynamic force transmitted to the payload, which was achieved in terms of 16 dB. The concept is presented in the first part of the paper and studied numerically and experimentally on a single degree of freedom isolator. A commercial isolator has been chosen for the purpose of the demonstration. The second part of the paper is dedicated to experimental validations on multi-degree of freedom scaled test benches. It is shown that the force feedback allows damping of both suspension and flexible modes (first and second modes, respectively), and significantly reducing the force transmitted in some broad frequency ranges.

Clinical application of a modern high-definition head-mounted display in sonography.

Science.gov (United States)

Takeshita, Hideki; Kihara, Kazunori; Yoshida, Soichiro; Higuchi, Saori; Ito, Masaya; Nakanishi, Yasukazu; Kijima, Toshiki; Ishioka, Junichiro; Matsuoka, Yoh; Numao, Noboru; Saito, Kazutaka; Fujii, Yasuhisa

2014-08-01

Because of the remarkably improved image quality and wearability of modern head-mounted displays, a monitoring system using a head-mounted display rather than a fixed-site monitor for sonographic scanning has the potential to improve the diagnostic performance and lessen the examiner's physical burden during a sonographic examination. In a preclinical setting, 2 head-mounted displays, the HMZ-T2 (Sony Corporation, Tokyo, Japan) and the Wrap1200 (Vuzix Corporation, Rochester, NY), were found to be applicable to sonography. In a clinical setting, the feasibility of the HMZ-T2 was shown by its good image quality and acceptable wearability. This modern device is appropriate for clinical use in sonography. © 2014 by the American Institute of Ultrasound in Medicine.

Examining risk factors for cardiovascular disease among food bank members in Vancouver

Directory of Open Access Journals (Sweden)

A.O. Fowokan

2018-06-01

Full Text Available Food banks provide supplemental food to low-income households, yet little is known about the cardiovascular health of food banks members. This study therefore described cardiovascular disease (CVD risk factors among food bank members and explored associations between food insecurity and CVD risk.Adults ≥18 years (n = 77 from three food bank sites in metro Vancouver, British Columbia completed surveys and physical assessments examining a range of socio-demographic variables and CVD risk factors. A composite measure of myocardial infarction (MI risk called the INTERHEART score was assessed and household food insecurity was measured using the Household Food Security Survey Module. Regression models were used to explore associations between food insecurity and CVD risk measures, including the INTERHEART score.Ninety-seven percent of food bank members reported experiencing food insecurity, 65% were current smokers, 53% reported either chronic or several periods of stress in the past year, 55% reported low physical activity levels and 80% reported consuming fewer than five servings of fruit and vegetables daily. Prevalence of self-reported diabetes and hypertension were 13% and 29% respectively. Fifty-two percent of the sample were at high risk of non-fatal MI. No statistically significant associations were found between increased severity of food insecurity and CVD risk factors among this sample where both severe food insecurity and high CVD risks were prevalent.Food bank members were at elevated risk for CVD compared with the general population. Strategies are needed to reduce prevalence of food insecurity and CVD risk factors, both of which disproportionately affected food bank members. Keywords: Food insecurity, Food banks, Cardiovascular disease, Risk factors, Canada