Raman Lidar Profiles–Temperature (RLPROFTEMP) Value-Added Product

Energy Technology Data Exchange (ETDEWEB)

Newsom, RK; Sivaraman, C; McFarlane, SA

2012-10-31

The purpose of this document is to describe the Raman Lidar Profiles–Temperature (RLPROFTEMP) value-added product (VAP) and the procedures used to derive atmospheric temperature profiles from the raw RL measurements. Sections 2 and 4 describe the input and output variables, respectively. Section 3 discusses the theory behind the measurement and the details of the algorithm, including calibration and overlap correction.

Conservation value of low-productivity forests measured as the amount and diversity of dead wood and saproxylic beetles.

Science.gov (United States)

Hämäläinen, Aino; Strengbom, Joachim; Ranius, Thomas

2018-06-01

In many managed landscapes, low-productivity land comprises most of the remaining relatively untouched areas, and is often over-represented within protected areas. The relationship between the productivity and conservational value of a site is poorly known; however, it has been hypothesized that biodiversity increases with productivity due to higher resource abundance or heterogeneity, and that the species communities of low-productivity land are a nested subset of communities from more productive land. We tested these hypotheses for dead-wood-dependent beetles by comparing their species richness and composition, as well as the amount and diversity of dead wood, between low-productivity (potential forest growth dead wood, but volume appeared to be a better predictor than diversity for the higher species richness in set-asides. Beetle species composition was similar among stand types, and the assemblages in low-productivity stands were largely subsets of those in high-productivity set-asides. However, 11% of all species and 40% of red-listed species only occurred in high-productivity stands, while no species were unique to low-productivity stands. We conclude that low-productivity forests are less valuable for conservation than high-productivity forest land. Given the generally similar species composition among stand types, a comparable conservational effect could be obtained by setting aside a larger area of low-productivity forest in comparison to the high-productivity. In terms of dead wood volumes, 1.8-3.6 ha of low-productivity forest has the same value as 1 ha of unmanaged high-productivity forest. This figure can be used to estimate the conservation value of low-productivity forests; however, as high-productivity forests harbored some unique species, they are not completely exchangeable. © 2018 The Authors. Ecological Applications published by Wiley Periodicals, Inc. on behalf of Ecological Society of America.

Analysis of Location Quotient index of poplar wood processing value chain in Iran

OpenAIRE

omid hosseinzadeh; Marzieh Hajjarian; Samira Porbar

2016-01-01

Value added in the poplar wood value chain has great economic effects for poplar farmers and have a fundamental role in sustainable supplying of required cellulosic materials of industries in long-term. The purpose of this study was to analyze the value chain of poplar and use the results to improve it. In order to determine the poplar value chain, Porter's value chain analysis framework was used. The statistical society consists of 76 experts to identify poplar wood value who were active in ...

PREDICTIVE MODEL FOR THE ADDED VALUE OF SULTANA SEEDLESS GRAPE PRODUCTION

Directory of Open Access Journals (Sweden)

Umut Burak Geyikci

2015-07-01

Full Text Available Turkey after USA is the second important raisin grape producer by cv “Sultana”in the world (Kara,2014. The Manisa district alone accounts for 31% of totalgrape production and 80% of the whole sultana seedless raisin grape production inTurkey. 95% of total grape output generated in Manisa is made up of Sultanaseedless grape(TUIK, 2012. In thisstudy, the added value of grape production inManisa has been calculated and according to the findings, the per capita addedvalue of grape production has been computed. In order to calculate the addedvalue of grape production in Manisa, costs of labor, fuel, fertilizer, disinfection,hormone, repair and maintenance of the businesses around have been investigated.After calculated costs had been deducted from total business income, the totaladded value of grape production in Manisa and the per capita added valueofgrape production in Manisa were attained The efficiency per hectare in the sampleproduction units, which was investigated during the field research, measures up to26.470 kg. The percentile distributions of cost items at this efficiency level are;27,8% fuel costs, 23,2% fertilizing costs, 19,9% irrigation costs, 11,4%disinfection costs, 7,5% hormone usage costs, 4,6% harvesting and transportingcosts and the rest consists of maintenance costs. When the costs are deducted from income per hectare (11.646 USD, the added value per hectare turns out to be8843 USD

Test marketing for value-added root and tuber based products in ...

African Journals Online (AJOL)

Test marketing for value-added root and tuber based products in Ikwuano local government area ... JE Ewuziem, C Aniedu, E Oti, VO Onyenobi ... root and tuber based products, developed at National Root Crops Research Institute, Umudike.

Effect of adding wood vinegar on cucumber (Cucumis sativus L) seed germination

Science.gov (United States)

Lei, Ming; Liu, Bingjie; Wang, Xiao

2018-03-01

Wood vinegar, a liquid by-product that was obtained from the condensed vapor generated during the biomass pyrolysis, had been reported as plant growth promotor, but the impact on the plant seeds was still not clear. Thus, we investigated the effects of wood vinegar on the germination and seedling growth of cucumber seeds through the germination experiments. The results showed that the different diluted wood vinegar addition showed no significant difference in the germination rates of cucumber seeds compared to those of the CK treatment (P > 0.05). However, the added wood vinegar at the 10000-time dilution significantly increased the root length and dry biomass of cucumber by 20.9 % and 5.92 %, respectively (P < 0.05). Therefore, the wood vinegar at an optimal time of dilution could be used a promising soaking agent for the seeds germination, and further enhance crop yields.

Organic Aerosol Component (OACOMP) Value-Added Product Report

Energy Technology Data Exchange (ETDEWEB)

Fast, J; Zhang, Q; Tilp, A; Shippert, T; Parworth, C; Mei, F

2013-08-23

Significantly improved returns in their aerosol chemistry data can be achieved via the development of a value-added product (VAP) of deriving OA components, called Organic Aerosol Components (OACOMP). OACOMP is primarily based on multivariate analysis of the measured organic mass spectral matrix. The key outputs of OACOMP are the concentration time series and the mass spectra of OA factors that are associated with distinct sources, formation and evolution processes, and physicochemical properties.

The contribution of technology to added value

CERN Document Server

Fernandes, António S C

2013-01-01

There is a wide consensus that introduction of technology to the production process contributes to an overall economic value, however, confusion between technology, knowledge and capital often makes value calculations ambiguous and non-objective. The Contribution of Technology to Added Value addresses not only this issue of definition but also provides a production model to assess the value contribution of technology within the production process. A clarification  of fundamental semantics  provides a significant taxonomy for technology dependence, and allows understanding and modeling of how knowledge, technology and capital individually contribute to production and to value adding. A new technology dependence taxonomy is proposed and assessed following chapters explaining growth models, the KTC model and technology index values. Balancing theoretical knowledge with real-world data and applications The Contribution of Technology to Added Value clarifies the issue of value adding for a range of different vie...

Value-Added Products from FGD Sulfite-Rich Scrubber Materials

Energy Technology Data Exchange (ETDEWEB)

Vivak Malhotra

2010-01-31

According to the American Coal Ash Association, about 29.25 million tons of flue gas desulfurization (FGD) byproducts were produced in the USA in 2003. Out of 29.25 million tons, 17.35 million tons were sulfite-rich scrubber materials. At present, unlike its cousin FGD gypsum, the prospect for effective utilization of sulfite-rich scrubber materials is not bright. In fact, almost 16.9 million tons are leftover every year. In our pursuit to mitigate the liability of sulfite-rich FGD scrubber materials' disposal, we are attempting to develop value-added products that can commercially compete. More specifically, for this Innovative Concept Phase I project, we have the following objectives: to characterize the sulfite-rich scrubber material for toxic metals; to optimize the co-blending and processing of scrubber material and natural byproducts; to formulate and develop structural composites from sulfite-rich scrubber material; and to evaluate the composites' mechanical properties and compare them with current products on the market. After successfully demonstrating the viability of our research, a more comprehensive approach will be proposed to take these value-added materials to fruition.

Sustainable multipurpose biorefineries for third-generation biofuels and value-added co-products

Science.gov (United States)

Modern biorefinery facilities conduct many types of processes, including those producing advanced biofuels, commodity chemicals, biodiesel, and value-added co-products such as sweeteners and bioinsecticides, with many more co-products, chemicals and biofuels on the horizon. Most of these processes ...

ARM Climate Research Facility Quarterly Value-Added Product Report

Energy Technology Data Exchange (ETDEWEB)

Sivaraman, Chitra

2014-01-14

The purpose of this report is to provide a concise status update for value-added products (VAP) implemented by the Atmospheric Radiation Measurement Climate Research Facility. The report is divided into the following sections: (1) new VAPs for which development has begun, (2) progress on existing VAPs, (3) future VAPs that have been recently approved, (4) other work that leads to a VAP, and (5) top requested VAPs from the archive.

Aquacultural and socio-economic aspects of processing carps into some value-added products.

Science.gov (United States)

Sehgal, H S; Sehgal, G K

2002-05-01

Carps are the mainstay of Indian aquaculture, contributing over 90% to the total fish production, which was estimated to be 1.77 million metric tonnes in 1996. Carp culture has a great potential for waste utilization and thus for pollution abatement. Many wastes such as cow, poultry, pig, duck, goat, and sheep excreta, biogas slurry, effluents from different kinds of factories/industries have been efficiently used for enhancing the productivity of natural food of carps and related species. Besides, several organic wastes/byproducts such as plant products, wastes from animal husbandry, and industrial by-products have been used as carp feed ingredients to lower the cost of supplementary feeding. However, to ensure the continued expansion of fish ponds and the pollution control, there must be a market for the fish (carps) produced in these ponds. The carps have, however, a low market value due to the presence of intra-muscular bones, which reduces their consumer acceptability. Thus, a need was felt to develop some boneless convenience products for enhancing the consumer acceptability of the carps. Efforts were made to prepare three value-added fish products, namely fish patty, fish finger and fish salad from carp flesh and were compared with a reference product ('fish pakoura'). Sensory evaluation of these products gave highly encouraging results. The methods of preparation of these products were transferred to some progressive farmers of the region who prepared and sold these products at very attractive prices. Carp processing has a great potential for the establishment of a fish ancillary industry and thus for boosting the production of these species. In Punjab alone, there is a potential of consuming 32,448 metric tonnes per annum of such value-added products (which would require 54,080 metric tonnes of raw fish). The development of value-added products has a significant role in raising the socio-economic status of the people associated with carp culture. The

Sustainability Impact Assessment on the Production and Use of Different Wood and Fossil Fuels Employed for Energy Production in North Karelia, Finland

Directory of Open Access Journals (Sweden)

Matias Pekkanen

2012-11-01

Full Text Available The utilization rate of woody biomass in eastern Finland is high and expected to increase further in the near future as set out in several regional, national and European policies and strategies. The aim of this study was to assess the sustainability impacts of changes in fuel consumption patterns. We investigated fossil and woody biomass-based energy production chains in the region of North Karelia, focusing on some economic, environmental and social indicators. Indicators were selected based on stakeholder preferences and evaluated using the Tool for Sustainability Impact Assessment (ToSIA. The analysis was based on representative values from National Forest Inventory data, scientific publications, national and regional statistics, databases, published policy targets and expert opinion. From the results it became evident that shifting from fossil to wood-based energy production implies some trade-offs. Replacing oil with woody biomass in energy production would increase the local value added remaining in the region, create employment opportunities and would reduce total GHG emissions. However, firewood, wood chips from small-diameter trees from early thinning and wood pellets have high production costs. Moreover, large greenhouse gas emission resulted from wood pellet production. The case study generated valuable reference data for future sustainability assessments and demonstrated the usefulness of ToSIA as a tool presenting existing knowledge on sustainability impacts of alternative energy supply chains to inform decision making.

Western Canadian wood residue production and consumption trends

International Nuclear Information System (INIS)

McCloy, B.

2006-01-01

This presentation considered various trends in western Canadian wood residue production and consumption. Potential markets for wood residue products were also discussed. Trends were reviewed by province for the years 2000-2004. British Columbia (BC) is currently the largest producer of residue in the country, and also retains the largest surpluses of bark, sawdust and shavings. Wood residues in BC are used in pulp and plywood mill production, as well as in the creation of particleboard and MDF. Surplus mill wood residue production in the province has greatly increased due to the Mountain Pine Beetle (MPB) infestation, which has in turn spurred expansion of the BC interior sawmill industry. The infestation has also resulted in a glut of pulp chips. Current wood residue products in Alberta are mostly used in pulp mill combined heat and power (CHP) systems, as well as for wood pellet production and the creation of particleboard and MDF. It was noted that surplus residues are rapidly declining in the province. Saskatchewan's wood residue storage piles are estimated to contain 2,900,000 BDt, while Manitoba surpluses are relatively minor. It was suggested that high natural gas prices have increased the payback on wood energy systems to approximately 2 years. The value of wood residue is now greater than $100/BDt as a substitute for natural gas once the wood energy system has been fully depreciated. Sawmills may now wish to consider equipping themselves to sell wood residue products, as most sawmills only require 20 per cent of their residues for heating purposes. It was concluded that markets for hog fuel wood pellets should be developed in Canada and internationally. Future markets may also develop if natural gas currently used in pulp mill power boilers and lime kilns is replaced with wood residue energy systems. refs., tabs., figs

Trade in Value Added (TiVA in EU New Member States (EU NMS

Directory of Open Access Journals (Sweden)

Ines Kersan-Škabić

2017-01-01

Full Text Available Contemporary trade analysis indicates the necessity of calculating trade in value added (TiVA which is created through global value chains (GVCs. This paper aims to determine the characteristics and importance of GVC trade in the EU new member states (EU NMS with special emphasis placed on the industry level. The results demonstrate different levels of GVC participation of the EU NMS, where Hungary is the most integrated country and Croatia the least integrated. Regional GVCs exist because a huge part of value added (VA comes from EU member states, as in gross export as well as in final demand (Europe as a hub. The most important source countries are Germany and Italy and there is also evidence of geographical and historical relations between the countries. The domination of backward participation has been found in the analysis made on the industrial level, i.e. the EU NMS are highly dependent on the import of intermediates for the production and export of final products. Strong interconnections between imports of intermediate products and exports of final products have been found in the manufacture of computers, electronics and optical products; manufacture of wood, paper, printing and reproduction. This research has contributed to the scarce literature concerning GVC (TiVA in EU NMS and has opened up new possibilities for further research and analysis.

Microalgal cultivation for value-added products: a critical enviro-economical assessment.

Science.gov (United States)

Kothari, Richa; Pandey, Arya; Ahmad, Shamshad; Kumar, Ashwani; Pathak, Vinayak V; Tyagi, V V

2017-08-01

The present review focuses on the cultivation of algal biomass for generating value-added products (VAP) and to assess their economic benefits and harmful environmental impact. Additionally, the impact of bioreactor designs on the yield of microalgal biomass for VAP is also considered. All these factors are discussed in relation to the impact of microalgae production on the bio-economy sector of commercial biotechnology.

Important Non-Wood Forest Products in Turkey: An Econometric Analysis

Directory of Open Access Journals (Sweden)

R. Kurt

2016-12-01

Full Text Available Wood resources obtained from forest and non-wood forest products (NWFP have gained great importance recently as their economic values keeps increasing by the day. In this study, forecasting of Turkish Non-Wood Forest Products such as thyme, bay leaves, salvia and pine nut export amounts was carried out using a linear regression analysis method for the next fifteen years based on the data for the years between 1990 and 2009. Moreover, estimated import values and actual import values from the last years were compered and analyzed. Finally, predictions on future trends were made.

An Analysis of the U.S. Wood Products Import Sector: Prospects for Tropical Wood Products Exporters

Directory of Open Access Journals (Sweden)

W.A.R.T.W. Bandara

2012-10-01

Full Text Available The U.S. has dramatically altered its wood product imports and exports during the past few years,and at present, it is the second largest wood product importer in the world. Hence, an understanding ofmarket structures, factors in selecting foreign suppliers, and the emphasis placed on environmentalissues/certification are critical to understand from the perspective of wood products importers in the U.S.This study provides an analysis of the U.S. wood products import sector with special emphasis on currentand future opportunities for tropical wood products exporters to the U.S. market.In this study, 158 wood products importers in the U.S. were surveyed using a mailingquestionnaire. The adjusted response rate was 40.6 percent. Results indicated that most of the respondentswere small to medium scale firms, but major importers of wood products. According to respondents,wood products to the U.S. mainly come from Brazil, Chile, and China. From the importers’ perspective,Brazilian wood products ranked first for its quality followed by wood products from Chile and Finland.Product quality, long term customer relationships, on-time delivery of orders, fair prices, and supplierreputation were the factors deemed important in selecting overseas suppliers. Majority of respondentswere importing certified wood products. FSC, SFI, and ISO 14000 were the mostly accepted certificationprograms. However, certification was not a major factor in foreign supplier selection criteria. Whenconsidered the U.S. wood products importers’ tendency to diversify their products and species imported,attractive opportunities exist for wood products suppliers from tropical countries.

Bioreactors for lignocellulose conversion into fermentable sugars for production of high added value products

OpenAIRE

Liguori, Rossana; Ventorino, Valeria; Pepe, Olimpia; Faraco, Vincenza

2015-01-01

Lignocellulosic biomasses derived from dedicated crops and agro-industrial residual materials are promising renewable resources for the production of fuels and other added value bioproducts. Due to the tolerance to a wide range of environments, the dedicated crops can be cultivated on marginal lands, avoiding conflict with food production and having beneficial effects on the environment. Besides, the agro-industrial residual materials represent an abundant, available, and cheap source of biop...

Meta-analysis of greenhouse gas displacement factors of wood product substitution

International Nuclear Information System (INIS)

Sathre, Roger; O'Connor, Jennifer

2010-01-01

A displacement factor can express the efficiency of using biomass to reduce net greenhouse gas (GHG) emission, by quantifying the amount of emission reduction achieved per unit of wood use. Here we integrate data from 21 different international studies in a meta-analysis of the displacement factors of wood products substituted in place of non-wood materials. We calculate the displacement factors in consistent units of tons of carbon (tC) of emission reduction per tC in wood product. The displacement factors range from a low of -2.3 to a high of 15, with most lying in the range of 1.0 to 3.0. The average displacement factor value is 2.1, meaning that for each tC in wood products substituted in place of non-wood products, there occurs an average GHG emission reduction of approximately 2.1 tC. Expressed in other units, this value corresponds to roughly 3.9 t CO 2 eq emission reduction per ton of dry wood used. The few cases of negative displacement factors are the result of worst-case scenarios that are unrealistic in current practice. This meta-analysis quantifies the range of GHG benefits of wood substitution, and provides a clear climate rationale for increasing wood substitution in place of other products, provided that forests are sustainably managed and that wood residues are used responsibly.

Meta-analysis of greenhouse gas displacement factors of wood product substitution

Energy Technology Data Exchange (ETDEWEB)

Sathre, Roger [Ecotechnology, Mid Sweden University, 83125 Ostersund (Sweden); O' Connor, Jennifer [FPInnovations-Forintek, Vancouver, BC, Canada V6T 1W5 (Canada)

2010-04-15

A displacement factor can express the efficiency of using biomass to reduce net greenhouse gas (GHG) emission, by quantifying the amount of emission reduction achieved per unit of wood use. Here we integrate data from 21 different international studies in a meta-analysis of the displacement factors of wood products substituted in place of non-wood materials. We calculate the displacement factors in consistent units of tons of carbon (tC) of emission reduction per tC in wood product. The displacement factors range from a low of -2.3 to a high of 15, with most lying in the range of 1.0 to 3.0. The average displacement factor value is 2.1, meaning that for each tC in wood products substituted in place of non-wood products, there occurs an average GHG emission reduction of approximately 2.1 tC. Expressed in other units, this value corresponds to roughly 3.9 t CO{sub 2} eq emission reduction per ton of dry wood used. The few cases of negative displacement factors are the result of worst-case scenarios that are unrealistic in current practice. This meta-analysis quantifies the range of GHG benefits of wood substitution, and provides a clear climate rationale for increasing wood substitution in place of other products, provided that forests are sustainably managed and that wood residues are used responsibly.

Wood working: planing and moulding in the last frontier

Science.gov (United States)

David Nicholls

2007-01-01

Planing and moulding is an important step in the value-added manufacture of wood products, and recent advances in Alaska have been noteworthy. Just a few years ago, most planing occurred on simple shop planers, producing lumber for retail sale or for wood working uses such as cabinet stock. Currently there are at least 26 planers and 13 moulders in-production at...

Emissions from laboratory combustor tests of manufactured wood products

Energy Technology Data Exchange (ETDEWEB)

Wilkening, R.; Evans, M.; Ragland, K. [Univ. of Wisconsin, Madison, WI (United States); Baker, A. [USDA Forest Products Lab., Madison, WI (United States)

1993-12-31

Manufactured wood products contain wood, wood fiber, and materials added during manufacture of the product. Manufacturing residues and the used products are burned in a furnace or boiler instead of landfilling. Emissions from combustion of these products contain additional compounds from the combustion of non-wood material which have not been adequately characterized to specify the best combustion conditions, emissions control equipment, and disposal procedures. Total hydrocarbons, formaldehyde, higher aldehydes and carbon monoxide emissions from aspen flakeboard and aspen cubes were measured in a 76 mm i.d. by 1.5 m long fixed bed combustor as a function of excess oxygen, and temperature. Emissions of hydrocarbons, aldehydes and CO from flakeboard and from clean aspen were very sensitive to average combustor temperature and excess oxygen. Hydrocarbon and aldehyde emissions below 10 ppM were achieved with 5% excess oxygen and 1,200{degrees}C average temperature for aspen flakeboard and 1,100{degrees}C for clean aspen at a 0.9 s residence time. When the average temperature decreased below these levels, the emissions increased rapidly. For example, at 950{degrees}C and 5% excess oxygen the formaldehyde emissions were over 1,000 ppM. These laboratory tests reinforce the need to carefully control the temperature and excess oxygen in full-scale wood combustors.

ARM Climate Research Facility Quarterly Value-Added Product Report

Energy Technology Data Exchange (ETDEWEB)

Sivaraman, C. [DOE ARM Climate Research Facility, Washington, DC (United States)

2016-10-01

The purpose of this report is to provide a concise status update for Value-Added Products (VAPs) implemented by the Atmospheric Radiation Measurement (ARM) Climate Research Facility. The report is divided into the following sections: (1) new VAPs for which development has begun; (2) progress on existing VAPs; (3) future VAPs that have been recently approved; (4) other work that leads to a VAP; (5) top requested VAPs from the ARM Data Archive; and (6) a summary of VAP and data releases to production and evaluation. New information is highlighted in blue text. New information about processed data by the developer is highlighted in red text. The upcoming milestones and dates are highlighted in green.

Impacts of adding different components of wood vinegar on rape (Brassica napus L.) seed germiantion

Science.gov (United States)

Shan, Xue; Liu, Xia; Zhang, Qian

2018-03-01

In recent years, wood vinegar has been widely used in the agricultural production. It can be used as the soil amendment, antibacterial agent and organic fertilizer. This study investigated the effect of wood vinegar on rape (Brassica napus L.) seed germination. The results in this study showed that 1% (v/v) wood vinegar had the greatest inhibition effect on the seed germination of rape (Brassica napus L.). The wood vinegar (WV) and the distilled wood vinegar at 98 - 130 °C (D2) significantly inhibited seed germination by 100%, compared to the control treatment. However, the distilled wood vinegar (D1) had significantly increased the shoot length and root length by 58.4% and 31.7%, respectively. These positive effects could be attributed to the improved soil fertility, increased nutrient supply, and further stimulated plant growth. Overall, the D1 could be a promising soil amendment to promote plants growth and enhance crop yields. Effect of adding different components of distilled wood vinegar on the seed germination of rape

The International Comparison of Value Added, Productivity and Purchasing Power Parities in Agriculture

NARCIS (Netherlands)

Maddison, Angus; Ooststroom, Harry van

1993-01-01

This study is part of the ICOP (International Comparison of Output and Productivity) project of the University of Groningen. It presents international comparisons of levels of value added, productivity and purchasing power parities (PPPs) in agriculture for 13 countries for 1975. An early version of

Realizing "value-added" metrology

Science.gov (United States)

Bunday, Benjamin; Lipscomb, Pete; Allgair, John; Patel, Dilip; Caldwell, Mark; Solecky, Eric; Archie, Chas; Morningstar, Jennifer; Rice, Bryan J.; Singh, Bhanwar; Cain, Jason; Emami, Iraj; Banke, Bill, Jr.; Herrera, Alfredo; Ukraintsev, Vladamir; Schlessinger, Jerry; Ritchison, Jeff

2007-03-01

The conventional premise that metrology is a "non-value-added necessary evil" is a misleading and dangerous assertion, which must be viewed as obsolete thinking. Many metrology applications are key enablers to traditionally labeled "value-added" processing steps in lithography and etch, such that they can be considered integral parts of the processes. Various key trends in modern, state-of-the-art processing such as optical proximity correction (OPC), design for manufacturability (DFM), and advanced process control (APC) are based, at their hearts, on the assumption of fine-tuned metrology, in terms of uncertainty and accuracy. These trends are vehicles where metrology thus has large opportunities to create value through the engineering of tight and targetable process distributions. Such distributions make possible predictability in speed-sorts and in other parameters, which results in high-end product. Additionally, significant reliance has also been placed on defect metrology to predict, improve, and reduce yield variability. The necessary quality metrology is strongly influenced by not only the choice of equipment, but also the quality application of these tools in a production environment. The ultimate value added by metrology is a result of quality tools run by a quality metrology team using quality practices. This paper will explore the relationships among present and future trends and challenges in metrology, including equipment, key applications, and metrology deployment in the manufacturing flow. Of key importance are metrology personnel, with their expertise, practices, and metrics in achieving and maintaining the required level of metrology performance, including where precision, matching, and accuracy fit into these considerations. The value of metrology will be demonstrated to have shifted to "key enabler of large revenues," debunking the out-of-date premise that metrology is "non-value-added." Examples used will be from critical dimension (CD

Importance of wood from planted forests for manufacturing industry

Directory of Open Access Journals (Sweden)

Victor Almeida De Araujo

2017-06-01

Full Text Available The manufactured wood products are essential to modern society, since they are made from renewable and recyclable raw material, characterizing a sustainable input. The objective of this study was to elucidate the importance of wood from planted forests in forest products manufacture of higher added value, addressing forest and wood contexts of topics related to education, resources, products, industry, government incentives, public policies and markets. Different from Europe, it was verified that Brazil does not support positively this important industrial sector, nevertheless it still presents growth potential due to range of wooden-based products. Thus, wood could reach a prominent position in Brazilian economy, if strategies and incentives were defined by rules and public policies..

ARM Climate Research Facility Spectral Surface Albedo Value-Added Product (VAP) Report

Energy Technology Data Exchange (ETDEWEB)

McFarlane, S; Gaustad, K; Long, C; Mlawer, E

2011-07-15

This document describes the input requirements, output data products, and methodology for the Spectral Surface Albedo (SURFSPECALB) value-added product (VAP). The SURFSPECALB VAP produces a best-estimate near-continuous high spectral resolution albedo data product using measurements from multifilter radiometers (MFRs). The VAP first identifies best estimates for the MFR downwelling and upwelling shortwave irradiance values, and then calculates narrowband spectral albedo from these best-estimate irradiance values. The methodology for finding the best-estimate values is based on a simple process of screening suspect data and backfilling screened and missing data with estimated values when possible. The resulting best-estimate MFR narrowband spectral albedos are used to determine a daily surface type (snow, 100% vegetation, partial vegetation, or 0% vegetation). For non-snow surfaces, a piecewise continuous function is used to estimate a high spectral resolution albedo at 1 min temporal and 10 cm-1 spectral resolution.

Mushroom cultivation, processing and value added products: a patent based review.

Science.gov (United States)

Singhal, Somya; Rasane, Prasad; Kaur, Sawinder; Garba, Umar; Singh, Jyoti; Raj, Nishant; Gupta, Neeru

2018-06-03

Edible mushrooms are an abundant source of carbohydrates, proteins, and multiple antioxidants and phytonutrients. This paper presents a general overview on the edible fungus describing the inventions made in the field of its cultivation, equipment and value added products. To understand and review the innovations and nutraceutical benefits of mushrooms as well as to develop interest regarding the edible mushrooms. Information provided in this review is based on the available research investigations and patents. Mushrooms are an edible source of a wide variety of antioxidants and phytonutrients with a number of nutraceutical properties including anti-tumor and anti-carcinogenic. Thus, several investigations are made for cultivation and improvement of the yield of mushrooms through improvisation of growth substrates and equipment used for mushroom processing. The mushroom has been processed into various products to increase its consumption, providing the health and nutritional benefit to mankind. This paper summarizes the cultivation practices of mushroom, its processing equipments, methods of preservation, value added based products, and its nutraceutical properties. The review also highlights the various scientific feats achieved in terms of patents and research publications promoting mushroom as a wholesome food. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Forest biorefinery: Potential of poplar phytochemicals as value-added co-products.

Science.gov (United States)

Devappa, Rakshit K; Rakshit, Sudip K; Dekker, Robert F H

2015-11-01

The global forestry industry after experiencing a market downturn during the past decade has now aimed its vision towards the integrated biorefinery. New business models and strategies are constantly being explored to re-invent the global wood and pulp/paper industry through sustainable resource exploitation. The goal is to produce diversified, innovative and revenue generating product lines using on-site bioresources (wood and tree residues). The most popular product lines are generally produced from wood fibers (biofuels, pulp/paper, biomaterials, and bio/chemicals). However, the bark and other tree residues like foliage that constitute forest wastes, still remain largely an underexploited resource from which extractives and phytochemicals can be harnessed as by-products (biopharmaceuticals, food additives and nutraceuticals, biopesticides, cosmetics). Commercially, Populus (poplar) tree species including hybrid varieties are cultivated as a fast growing bioenergy crop, but can also be utilized to produce bio-based chemicals. This review identifies and underlines the potential of natural products (phytochemicals) from Populus species that could lead to new business ventures in biorefineries and contribute to the bioeconomy. In brief, this review highlights the importance of by-products/co-products in forest industries, methods that can be employed to extract and purify poplar phytochemicals, the potential pharmaceutical and other uses of >160 phytochemicals identified from poplar species - their chemical structures, properties and bioactivities, the challenges and limitations of utilizing poplar phytochemicals, and potential commercial opportunities. Finally, the overall discussion and conclusion are made considering the recent biotechnological advances in phytochemical research to indicate the areas for future commercial applications from poplar tree species. Crown Copyright © 2015. Published by Elsevier Inc. All rights reserved.

Modern microbial solid state fermentation technology for future biorefineries for the production of added-value products

Directory of Open Access Journals (Sweden)

Musaalbakri Abdul Manan

2017-12-01

Full Text Available The promise of industrial biotechnology has been around since Chaim Weizmann developed acetone–butanol–ethanol fermentation at the University of Manchester in 1917 and the prospects nowadays look brighter than ever. Today’s biorefinery technologies would be almost unthinkable without biotechnology. This is a growing trend and biorefineries have also increased in importance in agriculture and the food industry. Novel biorefinery processes using solid state fermentation (SSF technology have been developed as alternative to conventional processing routes, leading to the production of added-value products from agriculture and food industry raw materials. SSF involves the growth of microorganisms on moist solid substrate in the absence of free-flowing water. Future biorefineries based on SSF aim to exploit the vast complexity of the technology to modify biomass produced by agriculture and the food industry for valuable by-products through microbial bioconversion. In this review, a summary has been made of the attempts at using modern microbial SSF technology for future biorefineries for the production of many added-value products ranging from feedstock for the fermentation process and biodegradable plastics to fuels and chemicals.

A Review of the Wood Pellet Value Chain, Modern Value/Supply Chain Management Approaches, and Value/Supply Chain Models

Directory of Open Access Journals (Sweden)

Natalie M. Hughes

2014-01-01

Full Text Available We reviewed 153 peer-reviewed sources to provide identification of modern supply chain management techniques and exploration of supply chain modeling, to offer decision support to managers. Ultimately, the review is intended to assist member-companies of supply chains, mainly producers, improve their current management approaches, by directing them to studies that may be suitable for direct application to their supply chains and value chains for improved efficiency and profitability. We found that information on supply chain management and modeling techniques in general is available. However, few Canadian-based published studies exist regarding a demand-driven modeling approach to value/supply chain management for wood pellet production. Only three papers were found specifically on wood pellet value chain analysis. We propose that more studies should be carried out on the value chain of wood pellet manufacturing, as well as demand-driven management and modeling approaches with improved demand forecasting methods.

Method for conversion of carbohydrate polymers to value-added chemical products

Science.gov (United States)

Zhang, Zongchao C [Norwood, NJ; Brown, Heather M [Kennewick, WA; Su, Yu [Richland, WA

2012-02-07

Methods are described for conversion of carbohydrate polymers in ionic liquids, including cellulose, that yield value-added chemicals including, e.g., glucose and 5-hydroxylmethylfurfural (HMF) at temperatures below 120.degree. C. Catalyst compositions that include various mixed metal halides are described that are selective for specified products with yields, e.g., of up to about 56% in a single step process.

Wood adhesives : vital for producing most wood products

Science.gov (United States)

Charles R. Frihart

2011-01-01

A main route for the efficient utilization of wood resources is to reduce wood to small pieces and then bond them together (Frihart and Hunt 2010). Although humankind has been bonding wood since early Egyptian civilizations, the quality and quantity of bonded wood products has increased dramatically over the past 100 years with the development of new adhesives and...

Implementation of methodology for analyzing the added value in a metallurgical industry of custom products

Directory of Open Access Journals (Sweden)

Paulo Cesar Mayer

2015-03-01

Full Text Available This paper addresses the implementation of a methodology for the analysis of added value in a job where steel sheets operations are processed by oxyfuel in a CNC (computer numerical control machine. The method used was based on a case study, followed by descriptive research by observing and recording the movements of the work. For this purpose, all the movements and tasks of the operators and the machine were defined, and classified according to the concepts adopted by Ohno (2002. Their chrono-analyses occurred in the period from March to June 2010 and later improvements were made throughout the workplace, allowing the elimination and reduction of losses, significant increase in the added value and increased occupation of the machine. Through this case study, it was found that the understandings of Ohno (2002 about the added value developed for an automotive industry manufacturing a standard product are perfectly applicable to a company that works with a production system under design and does not manufacture standard products

Study of activity based costing implementation for palm oil production using value-added and non-value-added activity consideration in PT XYZ palm oil mill

Science.gov (United States)

Sembiring, M. T.; Wahyuni, D.; Sinaga, T. S.; Silaban, A.

2018-02-01

Cost allocation at manufacturing industry particularly in Palm Oil Mill still widely practiced based on estimation. It leads to cost distortion. Besides, processing time determined by company is not in accordance with actual processing time in work station. Hence, the purpose of this study is to eliminates non-value-added activities therefore processing time could be shortened and production cost could be reduced. Activity Based Costing Method is used in this research to calculate production cost with Value Added and Non-Value-Added Activities consideration. The result of this study is processing time decreasing for 35.75% at Weighting Bridge Station, 29.77% at Sorting Station, 5.05% at Loading Ramp Station, and 0.79% at Sterilizer Station. Cost of Manufactured for Crude Palm Oil are IDR 5.236,81/kg calculated by Traditional Method, IDR 4.583,37/kg calculated by Activity Based Costing Method before implementation of Activity Improvement and IDR 4.581,71/kg after implementation of Activity Improvement Meanwhile Cost of Manufactured for Palm Kernel are IDR 2.159,50/kg calculated by Traditional Method, IDR 4.584,63/kg calculated by Activity Based Costing Method before implementation of Activity Improvement and IDR 4.582,97/kg after implementation of Activity Improvement.

Processing biogas planet digestates into value-added products -BIOVIRTA

Energy Technology Data Exchange (ETDEWEB)

Paavola, T.; Rintala, J. (MTT Agrifood Research Finland, Jokioinen (Finland)), Email: teija.paavola@mtt.fi; Sahltroem, L.; Maunuksela, L.; Torniainen, M. (Finnish Food Safety Authority, EVIRA, Helsinki (Finland)), Email: leena.sahlstrom@evira.fi; Kaparaju, P.; Rintala, J. (Univ. of Jyvaeskylae (Finland)), Email: jukka.rintala@jyu.fi; Vikman, M.; Kapanen, A. (VTT Technical Research Centre of Finland, Espoo (Finland)), Email: minna.vikman@vtt.fi

2010-10-15

The objective of BIOVIRTA project is to develop technologies and practices with which digestates, originating from anaerobic digestion of different organic wastes and by-products, can be refined to value-added and safe products for various end-uses. It is expected that the operational preconditions for biogas plants will be significantly enhanced when the end-products are proven safe and applicable. Selection of the raw materials for anaerobic codigestion is the main operational strategy that could influence the nutrient content in the digestate. This has been clearly established in the laboratory and full-scale studies with various digestates originating from different raw materials, e.g. rendering and slaughterhouse byproducts. The nutrient content in the digestate also affects the opportunities to produce refined digestate products. In this project, the possibilities for several processing technologies, e.g. mechanical separation and stripping, have been intensively evaluated for the production of different digestate products. Their mass balances have also been estimated. The feasibility for the use of the digestate products has been assessed based on their chemical and hygienic quality and for various end-uses, including as organic fertiliser and/or soil improver in crop production. The preliminary results of these field-experiments showed that the yield of barley fertilised with digestate products was comparable to inorganic fertilisers. (orig.)

THE ADDED VALUE OF SHREDDED LELE AND PATIN CATFISH

Directory of Open Access Journals (Sweden)

Ristina Siti Sundari

2017-09-01

Full Text Available Fish is not only perishable product but also has segmented market. Consumption market such wants the fresh fish and certainty size. The problem is when the size of fish is too big for consumption, so that product is not wanted by consumer anymore. This research aimed at knowing the added value of shredded Lele and Patin catfish agribusiness and increasing prosperity of humanitarian society throughout processing the shredded catfishes. The data of this research was analyzed by Added Value Analysis of Hayami. The result showed that the shredded product of Lele catfish gave the added value IDR 14.295,00 per kilograms with the added value ratio was 25,53 percent and Conversion value was 0,35. Whereas, the shredded product of Patin catfish gave the added value IDR 18.295,00 per kilogram with the added value ratio was 29,04 percent and Conversion value was 0,35. The agribusiness toward processing and marketing of shredded Lele and Patin catfish was innovative agribusiness that could develop business opportunity so that it could move on the economical wheel and increasing humanitarian society prosperity actively. The market demand was still very wide either in town or out of town. The partnership among various not only government but also non government associations would be a good matter toward this agribusiness is running well.

Doppler Lidar Vertical Velocity Statistics Value-Added Product

Energy Technology Data Exchange (ETDEWEB)

Newsom, R. K. [DOE ARM Climate Research Facility, Washington, DC (United States); Sivaraman, C. [DOE ARM Climate Research Facility, Washington, DC (United States); Shippert, T. R. [DOE ARM Climate Research Facility, Washington, DC (United States); Riihimaki, L. D. [DOE ARM Climate Research Facility, Washington, DC (United States)

2015-07-01

Accurate height-resolved measurements of higher-order statistical moments of vertical velocity fluctuations are crucial for improved understanding of turbulent mixing and diffusion, convective initiation, and cloud life cycles. The Atmospheric Radiation Measurement (ARM) Climate Research Facility operates coherent Doppler lidar systems at several sites around the globe. These instruments provide measurements of clear-air vertical velocity profiles in the lower troposphere with a nominal temporal resolution of 1 sec and height resolution of 30 m. The purpose of the Doppler lidar vertical velocity statistics (DLWSTATS) value-added product (VAP) is to produce height- and time-resolved estimates of vertical velocity variance, skewness, and kurtosis from these raw measurements. The VAP also produces estimates of cloud properties, including cloud-base height (CBH), cloud frequency, cloud-base vertical velocity, and cloud-base updraft fraction.

Health evaluation of volatile organic compound (VOC) emission from exotic wood products

DEFF Research Database (Denmark)

Kirkeskov, L; Witterseh, T; Funch, L W

2009-01-01

The purpose of this study was to measure and evaluate the impact of the emissions of selected products of exotic wood on health. Ten products were screened for chemical compounds, and five of the most used products which emitted more than 800 microg/kg were selected for further quantitative...... analyses by climate chamber measurement (iroko, ramin, sheesham, merbau, and rubber tree). Samples of exotic wood (rubber tree and belalu) were further analyzed for emission of chemical compounds by migration into artificial saliva and for content of pesticides and allergenic natural rubber latex (NR latex......) (rubber tree). The toxicological effects of all substances identified were evaluated and the lowest concentrations of interest (LCI) assessed. An R-value was calculated for each wood product (R-value below 1 is considered to be unproblematic as regards health). Emission from the evaluated exotic wood only...

Fifteen years of international trade in wood and forest-related products

International Nuclear Information System (INIS)

Desclos, Pierre-Marie

2014-01-01

Little is generally known about international trade in forest-related products in spite of the fact that a significant portion of world production is exported. Two irreversible trends underlie international trade in forest-related products. One is globalization while the other is adding as much value as possible locally by processing the materials to the greatest extent possible in the country of origin. Some of the more surprising recent developments are the growth in trade in wood as a source of energy and the dependency of Europe on its massive imports in this area. International trade in forest-related products is a continually changing sector that follows developments in the technical, economic, social and political spheres. Its growth has been spectacular and will remain strong in coming years. The greatest potential for development will come from environmental management, improved logistics and innovation. (authors)

Integrated biomass technologies: future vision for optimally using wood and biomass

Science.gov (United States)

Jerrold E. Winandy; Alan W. Rudie; R. Sam Williams; Theodore H. Wegner

2008-01-01

Exciting new opportunities are emerging for sustainably meeting many global energy needs and simultaneously creating high value biobased consumer and construction products from wood, forest and agricultural residues, and other biobased materials. In addition to traditional value added biobased products, such as lumber, paper, paperboard, and composites, opportunities...

Properties of Eucalyptus benthamii wood for energy production

Directory of Open Access Journals (Sweden)

Dimas Agostinho Silva

2015-12-01

Full Text Available The objective of this study was to evaluate the energy potential of Eucalyptus benthamii Maiden et Cambage wood. The samples were collected in the municipality of Cerro Negro, Santa Catarina State, Brazil. Samples were collected from 5 trees at 0%, 25%, 50%, 75% and 100% of commercial height. It was determined basic density, high calorific value, elemental composition, immediate chemical analysis, lower calorific value, energy density, carbon storage and energy production. The physical and chemical variables studied and energy potential of wood did not present differences along the stem.

Profiling value added position in FM

DEFF Research Database (Denmark)

Katchamart, Akarapong

. It is argued that being strategic is not the pre-requisite condition to add value to the core business and stakeholders but rather matching what does FM organization offer - so called FM product - with how does it being offered - so called FM process? By matching FM products with the right FM process, FM...... organizations can best add value. Based on comprehensive literature studies and 7 case studies of private and public organisations from Denmark, Holland, Hong Kong and Thailand, the dissertation analyses, how FM organizations can best create added value. From the analyses the following four value added...... positions have emerged: 1. Support - FM organizations create benefit to its host organization from economies of scope and scale 2. Enable - FM organizations increase the one-off organizational capacity and capability 3. Ensure - FM organizations contribute the business continuity and reliability 4. Enhance...

Value-Added Products Derived from Waste Activated Sludge: A Biorefinery Perspective

Directory of Open Access Journals (Sweden)

Wei Zhang

2018-04-01

Full Text Available Substantial research has been carried out on sustainable waste activated sludge (WAS management in the last decade. In addition to the traditional approach to reduce its production volume, considering WAS as a feedstock to produce bio-products such as amino acids, proteins, short chain fatty acids, enzymes, bio-pesticides, bio-plastics, bio-flocculants and bio-surfactants represents a key component in the transformation of wastewater treatment plants into biorefineries. The quality of these bio-products is a key factor with respect to the feasibility of non-conventional WAS-based production processes. This review provides a critical assessment of the production process routes of a wide range of value-added products from WAS, their current limitations, and recommendations for future research to help promote more sustainable management of this under-utilised and ever-growing waste stream.

Cloud Type Classification (cldtype) Value-Added Product

Energy Technology Data Exchange (ETDEWEB)

Flynn, Donna [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Shi, Yan [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lim, K-S [Korean Atomic Energy Research Inst., Daejeon (South Korea); Riihimaki, Laura [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2017-08-15

The Cloud Type (cldtype) value-added product (VAP) provides an automated cloud type classification based on macrophysical quantities derived from vertically pointing lidar and radar. Up to 10 layers of clouds are classified into seven cloud types based on predetermined and site-specific thresholds of cloud top, base and thickness. Examples of thresholds for selected U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility sites are provided in Tables 1 and 2. Inputs for the cldtype VAP include lidar and radar cloud boundaries obtained from the Active Remotely Sensed Cloud Location (ARSCL) and Surface Meteorological Systems (MET) data. Rain rates from MET are used to determine when radar signal attenuation precludes accurate cloud detection. Temporal resolution and vertical resolution for cldtype are 1 minute and 30 m respectively and match the resolution of ARSCL. The cldtype classification is an initial step for further categorization of clouds. It was developed for use by the Shallow Cumulus VAP to identify potential periods of interest to the LASSO model and is intended to find clouds of interest for a variety of users.

Microbial Conversion of Waste Glycerol from Biodiesel Production into Value-Added Products

Directory of Open Access Journals (Sweden)

Hong Liu

2013-09-01

Full Text Available Biodiesel has gained a significant amount of attention over the past decade as an environmentally friendly fuel that is capable of being utilized by a conventional diesel engine. However, the biodiesel production process generates glycerol-containing waste streams which have become a disposal issue for biodiesel plants and generated a surplus of glycerol. A value-added opportunity is needed in order to compensate for disposal-associated costs. Microbial conversions from glycerol to valuable chemicals performed by various bacteria, yeast, fungi, and microalgae are discussed in this review paper, as well as the possibility of extending these conversions to microbial electrochemical technologies.

The Carbon Impacts of Wood Products

Science.gov (United States)

Richard Bergman; Maureen Puettmann; Adam Taylor; Kenneth E. Skog

2014-01-01

Wood products have many environmental advantages over nonwood alternatives. Documenting and publicizing these merits helps the future competitiveness of wood when climate change impacts are being considered. The manufacture of wood products requires less fossil fuel than nonwood alternative building materials such as concrete, metals, or plastics. By nature, wood is...

Aluminum recovery as a product with high added value using aluminum hazardous waste

International Nuclear Information System (INIS)

David, E.; Kopac, J.

2013-01-01

Highlights: • Granular and compact aluminum dross were physically and chemically characterized. • A relationship between density, porosity and metal content from dross was established. • Chemical reactions involving aluminum in landfill and negative consequences are shown. • A processing method for aluminum recovering from aluminum dross was developed. • Aluminum was recovered as an value product with high grade purity such as alumina. -- Abstract: The samples of hazardous aluminum solid waste such as dross were physically and chemically characterized. A relationship between density, porosity and metal content of dross was established. The paper also examines the chemical reactions involving aluminum dross in landfill and the negative consequences. To avoid environmental problems and to recovery the aluminum, a processing method was developed and aluminum was recovered as an added value product such as alumina. This method refers to a process at low temperature, in more stages: acid leaching, purification, precipitation and calcination. At the end of this process aluminum was extracted, first as Al 3+ soluble ions and final as alumina product. The composition of the aluminum dross and alumina powder obtained were measured by applying the leaching tests, using atomic absorption spectrometry (AAS) and chemical analysis. The mineralogical composition of aluminum dross samples and alumina product were determined by X-ray diffraction (XRD) and the morphological characterization was performed by scanning electron microscopy (SEM). The method presented in this work allows the use of hazardous aluminum solid waste as raw material to recover an important fraction from soluble aluminum content as an added value product, alumina, with high grade purity (99.28%)

Water for wood products versus nature, food or feed

Science.gov (United States)

Schyns, Joep; Booij, Martijn; Hoekstra, Arjen

2017-04-01

Forests play a central interlinked role in the 2030 Agenda on Sustainable Development. The Agenda aims at an increased share of renewable energy in the global energy mix (target 7.2) and restoration and sustainable management of forests (targets 6.6, 15.1 & 15.2). Forests also play a key role in the hydrological cycle accounting for the largest water flux from land to atmosphere. However, we do not know which part of this is used for the production of wood products such as lumber, pulp and paper, firewood or biofuel. SDG target 6.4 calls for increased water-use efficiency across all sectors and requires understanding the competing demands for water and the potential conflicts between wood production and other purposes like food (SDG 2). To reach the SDGs we need to understand the interlinkages between the SDGs and know how much water is used in the forestry sector. We provide the first estimate of global water use in the forestry sector, using the water footprint (WF) as indicator and distinguishing between consumption of green water (precipitation) and blue water (groundwater through capillary rise). We estimate forest evaporation at a high spatial resolution level and attribute total water consumption to the various forest products, including ecosystem services. Global water consumption for wood production increased by 34% over 50 years to 290x109 m3/y in 2001-2010. Wood has a higher economic water productivity (EWP, US/m3) than common food or feed crops like wheat, maize and sugar beet, and bio-ethanol from wood has a small WF per unit of energy compared to first-generation bio-ethanol from these three crops. Counterintuitively, extensive wood production has a smaller WF and hence a higher EWP than intensive wood production. The reason is that extensively exploited forests host relatively more value next to wood production in the form of other ecosystem services. Recycling of wood products could effectively reduce the WF of the forestry sector, thereby leaving

Consequences of increasing bioenergy demand on wood and forests: An application of the Global Forest Products Model

Science.gov (United States)

Buongiorno, J.; Raunikar, R.; Zhu, S.

2011-01-01

The Global Forest Products Model (GFPM) was applied to project the consequences for the global forest sector of doubling the rate of growth of bioenergy demand relative to a base scenario, other drivers being maintained constant. The results showed that this would lead to the convergence of the price of fuelwood and industrial roundwood, raising the price of industrial roundwood by nearly 30% in 2030. The price of sawnwood and panels would be 15% higher. The price of paper would be 3% higher. Concurrently, the demand for all manufactured wood products would be lower in all countries, but the production would rise in countries with competitive advantage. The global value added in wood processing industries would be 1% lower in 2030. The forest stock would be 2% lower for the world and 4% lower for Asia. These effects varied substantially by country. ?? 2011 Department of Forest Economics, SLU Ume??, Sweden.

Exploring Valued-Added Options - Edge-Glued Panels and Blanks Offer Value-Added Opportunities

Science.gov (United States)

Bob Smith; Philip A. Araman

1997-01-01

As sawmills search for new opportunities to add value to rough sawn lumber, many consider producing dimension parts as one solution. Assembling dimension parts into edge-glued panels or standard blanks can add even further value. Blanks are defined as pieces of solid wood (which may be edge-glued) that are manufactured to a predetermined size. This article discusses...

Recent advances on conversion and co-production of acetone-butanol-ethanol into high value-added bioproducts.

Science.gov (United States)

Xin, Fengxue; Dong, Weiliang; Jiang, Yujia; Ma, Jiangfeng; Zhang, Wenming; Wu, Hao; Zhang, Min; Jiang, Min

2018-06-01

Butanol is an important bulk chemical and has been regarded as an advanced biofuel. Large-scale production of butanol has been applied for more than 100 years, but its production through acetone-butanol-ethanol (ABE) fermentation process by solventogenic Clostridium species is still not economically viable due to the low butanol titer and yield caused by the toxicity of butanol and a by-product, such as acetone. Renewed interest in biobutanol as a biofuel has spurred technological advances to strain modification and fermentation process design. Especially, with the development of interdisciplinary processes, the sole product or even the mixture of ABE produced through ABE fermentation process can be further used as platform chemicals for high value added product production through enzymatic or chemical catalysis. This review aims to comprehensively summarize the most recent advances on the conversion of acetone, butanol and ABE mixture into various products, such as isopropanol, butyl-butyrate and higher-molecular mass alkanes. Additionally, co-production of other value added products with ABE was also discussed.

THE INFLUENCE OF ECONOMIC VALUE ADDED AND MARKET VALUE ADDED ON CORPORATE VALUE

Directory of Open Access Journals (Sweden)

Taslim F.A.

2018-02-01

Full Text Available This research aims to determine the influence of economic value added and market value added on corporate value of manufacturing companies on sector consumer goods industry listed in Indonesia Stock Exchanges of 2011-2014. The sample of this research was 10 manufacturing companies on sector consumer goods industry listed in Indonesia Stock Exchanges. The method used was purposive sampling technique. This research used confirmatory factor analysis to form a combined proxy of corporate value comprised price earning ratio, price to book value and Tobin's Q.

Value-Added Electricity Services: New Roles for Utilities and Third-Party Providers

Energy Technology Data Exchange (ETDEWEB)

Blansfield, J. [Inst. for Electric Innovations, Washington, DC (United States); Wood, L. [Inst. for Electric Innovations, Washington, DC (United States); Katofsky, R. [Advanced Energy Economy, Washington, DC (United States); Stafford, B. [Advanced Energy Economy, Washington, DC (United States); Waggoner, D. [Advanced Energy Economy, Washington, DC (United States); Schwartz, L. C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2017-10-30

New energy generation, storage, delivery, and end-use technologies support a broad range of value-added electricity services for retail electricity customers. Sophisticated energy management services, distributed generation coupled with storage, and electric vehicle charging are just a few examples of emerging offerings. Who should provide value-added services — utilities or third parties, or both, and under what conditions? What policy and regulatory changes may be needed to promote competition and innovation, to account for utility costs to enable these services, and to protect consumers? The report approaches the issues from three perspectives: utilities, third-party service providers, and consumers: -Jonathan Blansfield and Lisa Wood, Institute for Electric Innovation -Ryan Katofsky, Benjamin Stafford and Danny Waggoner, Advanced Energy Economy -National Association of State Utility Consumer Advocates

The value chain of non-wood forest products as a component of development of the forestry sector in a part of South Serbia

Directory of Open Access Journals (Sweden)

Keča Ljiljana

2015-01-01

Full Text Available The value chain represents a detailed outline of the process that a product or service passes from raw materials, production and distribution to the consumer. The aim of this article is that within the analyzed companies in the area of the statistical region of South Serbia determined the dynamics of purchasing and marketing of non-wood forest products (NWFPs, and their value. The purpose of this research is to examine the possibilities for the development of small and medium-sized enterprises (SMEs towards sustainable use of NWFPs in a part of the territory of South Serbia. The subjects of the research are: purchased and sold quantities in analyzed companies, as well as the prices of these products in the market. The research was conducted in the territory of the dominant Pcinja, and they included 19 companies engaged in purchasing, processing and sale of NTFPs. The purchase of forest raspberries, wild strawberries and blackberries and herbs is represented within the Pcinja District. The highest average annual growth rates were recorded in the sales of products with added value of dog rose (Rosa canina and cornelian (Cornus mas. Export oriented enterprises in this area are at a low level. The total gross revenue earned by the placement of the selected final NWFPs in the domestic market was about 6,315,710 €. [Projekat Ministarstva nauke Republike Srbije, br. 37008: Održivo gazdovanje ukupnim potencijalima šuma u Republici Srbiji, i br. TP 31041: Šumski zasadi u funkciji povećanja pošumljenosti Srbije

Factors driving and restraining adoption of Automation technologies in Swedish wood product industry.

OpenAIRE

Mapulanga, Mwanza; Saladi, Praveen

2016-01-01

Swedish wood product industry contributes significantly to the economy of the country. This industry adds more value to the sawn timber produced in order to manufacture different wooden products. Companies in Swedish wood product industry are presently seen as underdeveloped in terms of investments and developments in automation technologies. Automation technologies are seen by companies as a solution for improving productivity, product quality, manufacturing cost reduction and ultimately imp...

Value added medicines: what value repurposed medicines might bring to society?

Science.gov (United States)

Toumi, Mondher; Rémuzat, Cécile

2017-01-01

Background & objectives : Despite the wide interest surrounding drug repurposing, no common terminology has been yet agreed for these products and their full potential value is not always recognised and rewarded, creating a disincentive for further development. The objectives of the present study were to assess from a wide perspective which value drug repurposing might bring to society, but also to identify key obstacles for adoption of these medicines and to discuss policy recommendations. Methods : A preliminary comprehensive search was conducted to assess how the concept of drug repurposing was described in the literature. Following completion of the literature review, a primary research was conducted to get perspective of various stakeholders across EU member states on drug repurposing ( healthcare professionals, regulatory authorities and Health Technology Assessment (HTA) bodies/payers, patients, and representatives of the pharmaceutical industry developing medicines in this field). Ad hoc literature review was performed to illustrate, when appropriate, statements of the various stakeholders. Results : Various nomenclatures have been used to describe the concept of drug repurposing in the literature, with more or less broad definitions either based on outcomes, processes, or being a mix of both. In this context, Medicines for Europe (http://www.medicinesforeurope.com/value-added-medicines/) established one single terminology for these medicines, known as value added medicines, defined as 'medicines based on known molecules that address healthcare needs and deliver relevant improvements for patients, healthcare professionals and/or payers'. Stakeholder interviews highlighted three main potential benefits for value added medicines: (1) to address a number of medicine-related healthcare inefficiencies related to irrational use of medicines, non-availability of appropriate treatment options, shortage of mature products, geographical inequity in medicine access

Designing products with added emotional value : development and application of an approach for research through design

NARCIS (Netherlands)

Desmet, P.M.A.; Overbeeke, C.J.; Tax, S.J.E.T.

2001-01-01

In this paper, a design approach is introduced for designing products with added emotional value. First, the approach was established, based on a theoretical framework and a non-verbal instrument to measure emotional responses. Second, the value of the design approach was assessed by applying it to

AMS 14C measurements for tree-ring samples from Japanese woods from 4c AD to 8c AD

International Nuclear Information System (INIS)

Ozaki, Hiromasa; Sakamoto, Minoru; Imamura, Mineo; Mitsutani, Takumi

2010-01-01

Regional offsets of atmospheric 14 C concentration, as represented by differences from IntCal calibration datasets, are discussed at times in relation to universal use of international radiocarbon calibration curve. In the construction of IntCal, 14 C contents of contemporaneous tree-ring samples from different regions in the northern hemisphere have been used, because the regional differences were indistinguishable from errors of measurements. Nowadays, high-precision 14 C results can be obtained much more easily than before, so more attention should be paid to the possible regional offsets. Most parts of IntCal has been constructed by using 14 C contents of tree-ring samples from woods in high latitude of Europe and North America, which are farthest from Japan in the northern hemisphere. So far, we have measured 14 C contents of tree-ring samples from Japanese wood samples dendrochronologically dated from 11th century BC to 4th century AD in order to investigate regional offset in Japan. Although the obtained results agreed well with IntCal in general, there were some periods when the 14 C contents differ significantly from IntCal. In this paper, we report the new results of AMS 14 C measurement for Japanese tree-ring samples ranging from 4th century AD to 8th century AD. The results show a significant disagreement with IntCal at around 630 AD. Similar difference was indicated by 14 C contents of tree-ring samples from other Japanese woods (Imamura et al., 2007). So it is certain that the regional offset in Japan exists at around 630 AD. (author)

Biodiesel production using heterogeneous catalysts including wood ash and the importance of enhancing byproduct glycerol purity

International Nuclear Information System (INIS)

Uprety, Bijaya K.; Chaiwong, Wittavat; Ewelike, Chinomnso; Rakshit, Sudip K.

2016-01-01

Highlights: • Comparison of biodiesel production using homogeneous and heterogeneous catalysts. • Comparative study of CaO and CaO supported on alumina for biodiesel production. • Tradeoff between biodiesel conversion rate and purity. • Ash from birch bark and wood pellet industry explored as a potential catalyst. - Abstract: Transesterification of vegetable oils or animal fats with methanol in the presence of catalysts produces fatty acid methyl esters (FAME) and glycerol as a co-product. This study was focused on a comparative study of the transesterification of refined, bleached and deodorized palm oil (RBD palm oil) using a heterogeneous catalysts CaO with and without γ-alumina (γ-Al_2O_3) as a support. The results were also compared to that using sodium hydroxide (NaOH), which is a homogenous catalyst. Parameters like the amount of catalyst, the molar ratio of methanol to oil, reaction time and reaction temperature that affect methyl ester and glycerol formation were analyzed and the optimum conditions were determined. The FAME and glycerol content (96.75% and 92.73% respectively) obtained using CaO were lower in purity compared to that using CaO/Al_2O_3 (97.66% and 96.36% respectively). In the second phase of our work, wood ash from two different sources (birch bark & flyash from a biomass based power plant), which were calcined at 800 °C were studied for their potential use as a cheap renewable alternative heterogeneous catalyst. Both the wood ash samples were found to have good potential for use in such production process, but needs to be optimized further to obtain biodiesel which meets fuel biodiesel specifications. Both CaO and CaO supported on alumina produces FAME to levels that meet the fuel specifications required for blending with diesel. However, the latter produces a purer form of byproduct glycerol that can be easily converted to value added products, without the need for purification. On this basis the supported catalyst is

Castanea sativa by-products: a review on added value and sustainable application.

Science.gov (United States)

Braga, Nair; Rodrigues, Francisca; Oliveira, M Beatriz P P

2015-01-01

Castanea sativa Mill. is a species of the family Fagaceae abundant in south Europe and Asia. The fruits (chestnut) are an added value resource in producing countries. Chestnut economic value is increasing not only for nutritional qualities but also for the beneficial health effects related with its consumption. During chestnut processing, a large amount of waste material is generated namely inner shell, outer shell and leaves. Studies on chestnut by-products revealed a good profile of bioactive compounds with antioxidant, anticarcinogenic and cardioprotective properties. These agro-industrial wastes, after valorisation, can be used by other industries, such as pharmaceutical, food or cosmetics, generating more profits, reducing pollution costs and improving social, economic and environmental sustainability. The purpose of this review is to provide knowledge about the type of chestnut by-products produced, the studies concerning its chemical composition and biological activity, and also to discuss other possible applications of these materials.

Wood for energy production. Technology - environment - economy

International Nuclear Information System (INIS)

Serup, H.; Falster, H.; Gamborg, C.

1999-01-01

'Wood for Energy Production', 2nd edition, is a readily understood guide to the application of wood in the Danish energy supply. The first edition was named 'Wood Chips for Energy Production'. It describes the wood fuel from forest to consumer and provides a concise introduction to technological, environmental, and financial matters concerning heating systems for farms, institutions, district heating plants, and CHP plants. The individual sections deal with both conventional, well known technology, as well as the most recent technological advances in the field of CHP production. The purpose of this publication is to reach the largest possible audiance, and it is designed so that the layman may find its background information of special relevance. 'Wood for Energy Production' is also available in German and Danish. (au)

Wood for energy production. Technology - environment - economy

Energy Technology Data Exchange (ETDEWEB)

Serup, H.; Falster, H.; Gamborg, C. [and others

1999-10-01

`Wood for Energy Production`, 2nd edition, is a readily understood guide to the application of wood in the Danish energy supply. The first edition was named `Wood Chips for Energy Production`. It describes the wood fuel from forest to consumer and provides a concise introduction to technological, environmental, and financial matters concerning heating systems for farms, institutions, district heating plants, and CHP plants. The individual sections deal with both conventional, well known technology, as well as the most recent technological advances in the field of CHP production. The purpose of this publication is to reach the largest possible audiance, and it is designed so that the layman may find its background information of special relevance. `Wood for Energy Production` is also available in German and Danish. (au)

The competitiveness of wood processing industry in the Republic of Serbia during the period 1995-2015

Directory of Open Access Journals (Sweden)

Milićević Srđan

2017-01-01

Full Text Available The paper considers the competitiveness of wood processing industry in the Republic of Serbia in the period 1995-2015 by using six partial indicators of competitiveness: Revealed comparative advantage (RCA, Competitiveness growth index (RCA1, Index of net business performance (RCA2, Index of contribution to the trade balance (CTB, Grubel-Lloyd index (GLI and Michaely index (MI. The research reveals that the values of RCA were positive in all years, which points to comparative advantage of wood processing industry on the domestic market. Since RCA1 has significantly higher value than one, it means that it is highly competitive on international market as well. Positive values of RCA2 in the period 1995-2015 speak of the contribution of this branch to international economic balance. The indicator RCA2 is connected with the CTB index, which points to the contribution of the sector in formation of active national trade balance and economic growth. The average value of CTB index of wood processing industry in Serbia and positive annual values of CTB of wood processing industry show that the contribution in the total trade balance of the sector is positive. The course of GLI values points to the loss of capabilities of the sector to create the surplus of national trade balance. Finally, positive annual values of MI confirmed the competitiveness of domestic wood processing industry, but at the same time its low specialisation. Taken as a whole, the weakness of competitiveness of wood processing industry in Serbia can be seen in the fact that its competitive advantage is visible in its favourable price, not in manufacturing complex products with high value added. The aim of the paper is to investigate whether Serbian wood processing industry has comparative precedence on domestic and international markets and whether the structure of exchange is positive, i.e. whether appropriate specialisation of production and export exists or the focus should shift

Ka-Band ARM Zenith Radar Corrections Value-Added Product

Energy Technology Data Exchange (ETDEWEB)

Johnson, Karen [Brookhaven National Lab. (BNL), Upton, NY (United States); Toto, Tami [Brookhaven National Lab. (BNL), Upton, NY (United States); Giangrande, Scott [Brookhaven National Lab. (BNL), Upton, NY (United States)

2017-10-15

The KAZRCOR Value -added Product (VAP) performs several corrections to the ingested KAZR moments and also creates a significant detection mask for each radar mode. The VAP computes gaseous attenuation as a function of time and radial distance from the radar antenna, based on ambient meteorological observations, and corrects observed reflectivities for that effect. KAZRCOR also dealiases mean Doppler velocities to correct velocities whose magnitudes exceed the radar’s Nyquist velocity. Input KAZR data fields are passed through into the KAZRCOR output files, in their native time and range coordinates. Complementary corrected reflectivity and velocity fields are provided, along with a mask of significant detections and a number of data quality flags. This report covers the KAZRCOR VAP as applied to the original KAZR radars and the upgraded KAZR2 radars. Currently there are two separate code bases for the different radar versions, but once KAZR and KAZR2 data formats are harmonized, only a single code base will be required.

Advanced wood- and bio-composites : enhanced performance and sustainability

Science.gov (United States)

Jerrold E. Winandy

2006-01-01

Use of wood-based-composites technology to create value-added commodities and traditional construction materials is generally accepted worldwide. Engineered wood- and lignocellulosic-composite technologies allow users to add considerable value to a diverse number of wood- and lignocellulosic feedstocks including small-diameter timber, fast plantation-grown timber,...

Lignocellulose: A sustainable material to produce value-added products with a zero waste approach-A review.

Science.gov (United States)

Arevalo-Gallegos, Alejandra; Ahmad, Zanib; Asgher, Muhammad; Parra-Saldivar, Roberto; Iqbal, Hafiz M N

2017-06-01

A novel facility from the green technologies to integrate biomass-based carbohydrates, lignin, oils and other materials extraction and transformation into a wider spectrum of marketable and value-added products with a zero waste approach is reviewed. With ever-increasing scientific knowledge, worldwide economic and environmental consciousness, demands of legislative authorities and the manufacture, use, and removal of petrochemical-based by-products, from the last decade, there has been increasing research interests in the value or revalue of lignocellulose-based materials. The potential characteristics like natural abundance, renewability, recyclability, and ease of accessibility all around the year, around the globe, all makes residual biomass as an eco-attractive and petro-alternative candidate. In this context, many significant research efforts have been taken into account to change/replace petroleum-based economy into a bio-based economy, with an aim to develop a comprehensively sustainable, socially acceptable, and eco-friendly society. The present review work mainly focuses on various aspects of bio-refinery as a sustainable technology to process lignocellulose 'materials' into value-added products. Innovations in the bio-refinery world are providing, a portfolio of sustainable and eco-efficient products to compete in the market presently dominated by the petroleum-based products, and therefore, it is currently a subject of intensive research. Copyright © 2017 Elsevier B.V. All rights reserved.

Material property characterization of co-products from biofuel industries: Potential uses in value-added biocomposites

International Nuclear Information System (INIS)

Diebel, William; Reddy, Murali M.; Misra, Manju; Mohanty, Amar

2012-01-01

This paper gives an insight of biofuel production and the status -into the co-products obtained from this industry. Furthermore this work explores the possibility of these co-products as raw materials for value-added uses in material applications. This is achieved by understanding composition, solid density, and moisture content of prominent co-products such as soy meal, DDGS (distillers’ dried grains with solubles) and jatropha meal. Moisture content and density measurements showed no trend. Soy meal has the highest protein content, followed by jatropha and DDGS. Thermal stability of these co-products was analyzed by thermogravimetric analysis (TGA), which revealed that the thermal stabilities are ranked as soy meal>DDGS>jatropha meal. FT-IR spectroscopy was used to understand the functional groups in these meals and it showed that the amide group was prominent in all of these meals. In pursuit of finding value-added uses for these co-products of biofuel industries, biodegradable polymer, i.e. polycaprolactone (PCL), based biocomposites were prepared by melt processing technique using extrusion followed by injection molding. Tensile, flexural and impact properties were evaluated. Also, scanning electron microscopy (SEM) of fractured sections of the biocomposites was examined. -- Highlights: ► This paper gives an insight of biofuel production and its co-products. ► We have characterized biofuel co-products such as soy meal, DDGS and jatropha meal. ► Thermal stability and functional groups of these co-products were determined. ► Polycaprolactone based biocomposites were prepared by melt processing technique. ► Tensile, flexural and impact properties of these biocomposites were evaluated.

Value Added Products from Hemicellulose Utilization in Dry Mill Ethanol Plants

Energy Technology Data Exchange (ETDEWEB)

Rodney Williamson, ICPB; John Magnuson, PNNL; David Reed, INL; Marco Baez, Dyadic; Marion Bradford, ICPB

2007-03-30

The Iowa Corn Promotion Board is the principal contracting entity for this grant funded by the US Department of Agriculture and managed by the US Department of Energy. The Iowa Corn Promotion Board subcontracted with New Jersey Institute of Technology, KiwiChem, Pacific Northwest National Lab and Idaho National Lab to conduct research for this project. KiwiChem conducted the economic engineering assessment of a dry-mill ethanol plant. New Jersey Institute of Technology conducted work on incorporating the organic acids into polymers. Pacific Northwest National Lab conducted work in hydrolysis of hemicellulose, fermentation and chemical catalysis of sugars to value-added chemicals. Idaho National Lab engineered an organism to ferment a specific organic acid. Dyadic, an enzme company, was a collaborator which provided in-kind support for the project. The Iowa Corn Promotion Board collaborated with the Ohio Corn Marketing Board and the Minnesota Corn Merchandising Council in providing cost share for the project. The purpose of this diverse collaboration was to integrate the hydrolysis, the conversion and the polymer applications into one project and increase the likelihood of success. This project had two primary goals: (1) to hydrolyze the hemicellulose fraction of the distillers grain (DG) coproduct coming from the dry-mill ethanol plants and (2) convert the sugars derived from the hemicellulose into value-added co-products via fermentation and chemical catalysis.

Nutritional composition of Chickpea (Cicerarietinum-L and value added products - a review

Directory of Open Access Journals (Sweden)

Harsha Hirdyani

2014-12-01

Full Text Available Chickpea (Cicer arietinum L. is an important pulse crop grown and consumed all over the world, especially in the Afro-Asian countries. It is a good source of carbohydrates and protein, and the protein quality is considered to be better than other pulses. Chickpea has significant amounts of all the essential amino acids. Starch is the major storage carbohydrate followed by dietary fibre, lipids are present in low amounts but chickpea is rich in nutritionally important unsaturated fatty acids like linoleic and oleic acid.It can be utilized to develop nutritious value added products and hence products can also be used as nutritious food for low income group in developing countries and for patients suffering with life style diseases.

Studies on the preparation of value-added products for industrial minerals

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

This report consists of 2 subjects. 1) Studies on the preparation of value-added products for limestone: This study has investigated to raise to high grade by economical processes with low grade of domestic limestone. We investigated the status of application utilize and related industries with the domestic limestone, and then being consideration with condition selected the adequate sample from Andong, Jungsun and Kumsan area. Magnetic materials were involved in impurities of sample, so magnetic separation method was applied in elimination of the ferro- and para-magnetic materials, such as chlorite, muscovite, quartz, dolomite, magnetite, feldspar and so on. Investigation of flotation was undertaken to eliminate impurities from limestone crude ore and the tests were performed to get a optimum condition adding oleic acid as a promoter, sodium silicate and sodium carbonate as a conditioning agents and MIBC as a frother, while to float the sulfide minerals added amyl xanthate as a promoter, and sulfuric acid as a pH regulator. Selective crushing and classification methods were performed to eliminate impurities depends on the mineral properties and should be the selective crushing methods are very useful at the manufacturing factory of heavy calcium carbonate with the dry milling system. 2) A study on development of value added technology of pyrophyllite and dickite: Pyrophyllite and dickite have being utilized as refractories, ceramics, cement, fiber glass, paper, rubber, paints etc. However, there are not any domestic companies to produce fillers of pyrophyllite and dickite for plastic and rubber. Moreover, several kinds of fillers are imported every year with expensive price for plastic and rubber filler. This study has purpose to develop manufacturing technologies to produce fillers for plastic and rubber of pyrophyllite and dickite. The chemical and mineralogical properties of samples, the optimum grinding condition and device for producing plastic fillers and

Linear equations on thermal degradation products of wood chips in alkaline glycerol

International Nuclear Information System (INIS)

Demirbas, Ayhan

2004-01-01

Wood chips of 0.3 and 2 mm depth from poplar and spruce wood samples, respectively, were degraded by using glycerol as a solvent and alkaline glycerol with and without Na 2 CO 3 and NaOH catalysts at different degradation temperatures: 440, 450, 460, 470, 480, 490 and 500 K. By products from the degradation processes of the ligno celluloses include lignin degradation products. Lignin and its degradation products have fuel values. The total degradation degree and cellulose degradation of the wood chips were determined to find the relationship, if any, between the yields of total degradation degree (YTD) and degradation temperature (T). There is a good linear relationship between YTD or the yields of cellulose degradation (YCD) and T (K). For the wood samples, the regression equations from NaOH (10%) catalytic runs for 0.3 mm x 15 mm x 15 mm chip size are: For poplar wood: (YTD=0.7250T-267.507) (YCD=0.1736T-71.707) For spruce wood: (YTD=0.2650T-105.979) (YCD=0.0707T-27.507) For Eqs., the square of the correlation coefficient (r 2 ) were 0.9841, 0.9496, 0.9839 and 0.9447, respectively

Value added tax-theoretical and practical aspects

Directory of Open Access Journals (Sweden)

Raičević Božidar B.

2004-01-01

Full Text Available Value added tax has been applied for four decades now and as a novelty it has already worn off both in theory and practice. It has indisputable advantages and relatively minor shortcomings compared to other forms of consumption taxation. Today it is one of the most widely used form of consumption tax in the world, being levied in about 120 countries accounting for around 70 per cent of the world population, including all European countries except Serbia and Bosnia and Herzegovina (the Federation and the Republic of Srpska. The burden of value added tax is visible at each stage in the production and distribution chain, thus eliminating taxation accumulation and is borne ultimately by the final consumer of final goods and services in the consuming country. The consumption type is a dominant type of value added tax. It ensures that the fixed and current assets purchases are exempt from VAT, and as such, it encourages technological progress and investment. By applying the country of destination principle (VAT is chargeable in the country where the goods or services are consumed - exports are exempt from tax while imports are taxed, value added tax eliminates double taxation and retains tax sovereignty of the importing country. In the last ten years there have been attempts to introduce value added tax in Serbia. The introduction of value added tax is the condition for the accession to the EU and we should expect that the latest attempt to introduce this tax in the Serbia taxation system will be successful. Namely, VAT Act is expected to be passed during 2004 and enforced as of January 1, 2005.

Lipid and fatty acid metabolism in Ralstonia eutropha: relevance for the biotechnological production of value-added products.

Science.gov (United States)

Riedel, Sebastian L; Lu, Jingnan; Stahl, Ulf; Brigham, Christopher J

2014-02-01

Lipid and fatty acid metabolism has been well studied in model microbial organisms like Escherichia coli and Bacillus subtilis. The major precursor of fatty acid biosynthesis is also the major product of fatty acid degradation (β-oxidation), acetyl-CoA, which is a key metabolite for all organisms. Controlling carbon flux to fatty acid biosynthesis and from β-oxidation allows for the biosynthesis of natural products of biotechnological importance. Ralstonia eutropha can utilize acetyl-CoA from fatty acid metabolism to produce intracellular polyhydroxyalkanoate (PHA). R. eutropha can also be engineered to utilize fatty acid metabolism intermediates to produce different PHA precursors. Metabolism of lipids and fatty acids can be rerouted to convert carbon into other value-added compounds like biofuels. This review discusses the lipid and fatty acid metabolic pathways in R. eutropha and how they can be used to construct reagents for the biosynthesis of products of industrial importance. Specifically, how the use of lipids or fatty acids as the sole carbon source in R. eutropha cultures adds value to these biotechnological products will be discussed here.

The global wood furniture value chain: what prospects for upgrading by developing countries? The case of South Africa

OpenAIRE

Kaplinsky, Raphael; Memedovic, Olga; Morris, Mike; Readman, Jeff

2003-01-01

Because of its resource and labour intensity, the wood furniture sector presents an opportunity for developing countries and their firms to participate effectively in the global economy. This paper begins with a brief description of the global wood furniture industry and highlights the importance of exports wood furniture products for developing countries and emerging and transitional economies. The paper then maps the wood furniture value chain and opens-up the nature of the buying function,...

Value-added biotransformation of cellulosic sugars by engineered Saccharomyces cerevisiae.

Science.gov (United States)

Lane, Stephan; Dong, Jia; Jin, Yong-Su

2018-07-01

The substantial research efforts into lignocellulosic biofuels have generated an abundance of valuable knowledge and technologies for metabolic engineering. In particular, these investments have led to a vast growth in proficiency of engineering the yeast Saccharomyces cerevisiae for consuming lignocellulosic sugars, enabling the simultaneous assimilation of multiple carbon sources, and producing a large variety of value-added products by introduction of heterologous metabolic pathways. While microbial conversion of cellulosic sugars into large-volume low-value biofuels is not currently economically feasible, there may still be opportunities to produce other value-added chemicals as regulation of cellulosic sugar metabolism is quite different from glucose metabolism. This review summarizes these recent advances with an emphasis on employing engineered yeast for the bioconversion of lignocellulosic sugars into a variety of non-ethanol value-added products. Copyright © 2018 Elsevier Ltd. All rights reserved.

Wood ethanol and synthetic natural gas pathways

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-11-30

This report provided details of updates to the wood ethanol pathway recently added to the GHGenius model, an analytical tool used to analyze emissions from conventional and alternative fuel combustion processes. The pathway contains data developed by the United States Department of Energy. A number of co-products were added to the wood and agricultural residue pathways, including furfural, xylitol, lignin, and glycerol. New chemical inputs included nitrogen gas, ammonia, enzymes and yeast. Biological ethanol pathways were reviewed, and separate inputs for wood, agricultural residues, corn ethanol, and wheat ethanol were added. The model was updated to reflect current research conducted on the gasification of wood and the upgrading of the gas to produce pipeline quality natural gas. New process developments in producing pipeline quality gas from coal were also added. The ability to model enzyme consumption was added to all ethanol pathways. 25 refs., 41 tabs., 8 figs.

Wood ethanol and synthetic natural gas pathways

International Nuclear Information System (INIS)

2006-01-01

This report provided details of updates to the wood ethanol pathway recently added to the GHGenius model, an analytical tool used to analyze emissions from conventional and alternative fuel combustion processes. The pathway contains data developed by the United States Department of Energy. A number of co-products were added to the wood and agricultural residue pathways, including furfural, xylitol, lignin, and glycerol. New chemical inputs included nitrogen gas, ammonia, enzymes and yeast. Biological ethanol pathways were reviewed, and separate inputs for wood, agricultural residues, corn ethanol, and wheat ethanol were added. The model was updated to reflect current research conducted on the gasification of wood and the upgrading of the gas to produce pipeline quality natural gas. New process developments in producing pipeline quality gas from coal were also added. The ability to model enzyme consumption was added to all ethanol pathways. 25 refs., 41 tabs., 8 figs

Recent advances in engineering propionyl-CoA metabolism for microbial production of value-added chemicals and biofuels.

Science.gov (United States)

Srirangan, Kajan; Bruder, Mark; Akawi, Lamees; Miscevic, Dragan; Kilpatrick, Shane; Moo-Young, Murray; Chou, C Perry

2017-09-01

Diminishing fossil fuel reserves and mounting environmental concerns associated with petrochemical manufacturing practices have generated significant interests in developing whole-cell biocatalytic systems for the production of value-added chemicals and biofuels. Although acetyl-CoA is a common natural biogenic precursor for the biosynthesis of numerous metabolites, propionyl-CoA is unpopular and non-native to most organisms. Nevertheless, with its C3-acyl moiety as a discrete building block, propionyl-CoA can serve as another key biogenic precursor to several biological products of industrial importance. As a result, engineering propionyl-CoA metabolism, particularly in genetically tractable hosts with the use of inexpensive feedstocks, has paved an avenue for novel biomanufacturing. Herein, we present a systematic review on manipulation of propionyl-CoA metabolism as well as relevant genetic and metabolic engineering strategies for microbial production of value-added chemicals and biofuels, including odd-chain alcohols and organic acids, bio(co)polymers and polyketides. [Formula: see text].

PRESTO: online calculation of carbon in harvested wood products

Science.gov (United States)

Coeli M. Hoover; Sarah J. Beukema; Donald C.E. Robinson; Katherine M. Kellock; Diana A. Abraham

2014-01-01

Carbon stored in harvested wood products is recognized under international carbon accounting protocols, and some crediting systems may permit the inclusion of harvested wood products when calculating carbon sequestration. For managers and landowners, however, estimating carbon stored in harvested wood products may be difficult. PRESTO (PRoduct EStimation Tool Online)...

Wood for energy production. Technology - environment - economy[Denmark

Energy Technology Data Exchange (ETDEWEB)

Serup, H.; Falster, H.; Gamborg, C. [and others

1999-07-01

'Wood for Energy Production', 2nd edition, is a readily understood guide to the application of wood in the Danish energy supply. The first edition was named 'Wood Chips for Energy Production'. It describes the wood fuel from forest to consumer and provides a concise introduction to technological, environmental, and financial matters concerning heating systems for farms, institutions, district heating plants, and CHP plants. The individual sections deal with both conventional, well known technology, as well as the most recent technological advances in the field of CHP production. The purpose of this publication is to reach the largest possible audiance, and it is designed so that the layman may find its background information of special relevance. 'Wood for Energy Production' is also available in German and Danish. (au)

THE EFFECT OF LEVERAGE AND ECONOMIC VALUE ADDED ON MARKET VALUE ADDED

OpenAIRE

Kristína Jančovičová BOGNÁROVÁ

2018-01-01

Economic value added (EVA) is a performance measure developed by Stern Stewart & Co.) that attempts to measure the true economic profit produced by a company. Such a metric is useful for investors who wish to determine how well a company has produced value for its investors, and it can be compared against the company's peers for a quick analysis of how well the company is operating in its industry. Market value added (MVA), on the other hand, is simply the difference between the c...

Wood-based bioenergy value chain in mountain urban districts: An integrated environmental accounting framework

International Nuclear Information System (INIS)

Nikodinoska, Natasha; Buonocore, Elvira; Paletto, Alessandro; Franzese, Pier Paolo

2017-01-01

Highlights: • The Sarentino bioenergy value chain (North Italy) was investigated. • A multi-method environmental accounting framework was implemented. • Environmental costs and impacts of a forest bioenergy chain were assessed. • Indicators show a good environmental performance and sustainability. • Linking wood industry and energy production could lower the environmental burden. - Abstract: Using wood biomass for bioenergy production in mountain urban settlements can represent a win–win strategy when it combines a continuous energy provision to households with a sustainable management of local forests, also boosting rural development and stakeholders’ cooperation. In this study, we implemented a multi-method environmental accounting framework aimed at investigating environmental costs and impacts of a bioenergy value chain located in Sarentino Valley (North Italy). This assessment framework encompasses material, energy, and emergy demands as well as main emissions generated at each step of the chain: (1) forestry, (2) logistics, and (3) conversion. The resulting global to local ratios of abiotic material calculated for forestry, logistics, and conversion subsystems show that the global (direct and indirect) consumption of abiotic matter was respectively 3.6, 3.2, and 7.6 times higher than the direct material demand. The Energy Return on Energy Investment (EROI) of wood biomass and wood chips production (37.1 and 22.4) shows a high energy performance of these processes, while the EROI of heat generation (11.35) reflects a higher support of human-driven inputs. The emergy renewable fraction, ranging from 77% to 37% across the value chain, shows a high use of local renewable resources in the bioenergy value chain. The total CO_2 emissions of the bioenergy value chain (4088 t CO_2 yr"−"1) represent only 7.1% of the CO_2 sequestration potential of the Sarentino Valley forest ecosystem, highlighting the capability of the local forests to offset the CO_2

Myths & Facts about Value-Added Analysis

Science.gov (United States)

TNTP, 2011

2011-01-01

This paper presents myths as well as facts about value-added analysis. These myths include: (1) "Value-added isn't fair to teachers who work in high-need schools, where students tend to lag far behind academically"; (2) "Value-added scores are too volatile from year-to-year to be trusted"; (3) "There's no research behind value-added"; (4) "Using…

Perbedaan Perusahan Pencipta Economic Value Added Positif Dengan Economic Value Added Negatif

OpenAIRE

Suripto, Suripto

2008-01-01

This research was to explain and analyze the different variable of Inflation Rate,Exchange Rate, Interest Rate, Ratio Plant Asset, Size Measure Company, Profitability, Growth ,LD / E, TD / TA, Stock of Return, Book To Market between company having Economic ValueAdded ( Positive ) and company having Economic Value Added ( Negative ). Analysis which wasused in this research was multivariate analysis of variant (MANOVA). There was different variableof Inflation Rate, Exchange Rate, Interest Rate...

The sustainable wood production initiative.

Science.gov (United States)

Robert. Deal

2004-01-01

To address concerns about sustainable forestry in the region, the Focused Science Delivery Program is sponsoring a three year Sustainable Wood Production Initiative. The Pacific Northwest is one of the world's major timber producing regions, and the ability of this region to produce wood on a sustained yield basis is widely recognized. Concerns relating to the...

Harvested wood products : basis for future methodological development

Science.gov (United States)

Kenneth E. Skog

2003-01-01

The IPCC Guidelines (IPCC 1997) provide an outline of how harvested wood could be treated in national greenhouse gas (GHG) inventories. This section shows the relation of that outline to the approaches and estimation methods to be presented in this Appendix. Wood and paper products are referred to as harvested wood products (HWP). It does not include carbon in...

Value-added Chemicals from Biomass by Heterogeneous Catalysis

DEFF Research Database (Denmark)

Voss, Bodil

feedstock, having retained one C-C bond originating from the biomass precursor, the aspects of utilising heterogeneous catalysis for its conversion to value added chemicals is investigated. Through a simple analysis of known, but not industrialised catalytic routes, the direct conversion of ethanol....... The results of the thesis, taking one example of biomass conversion, show that the utilisation of biomass in the production of chemicals by heterogeneous catalysis is promising from a technical point of view. But risks of market price excursions dominated by fossil based chemicals further set a criterion...... been implemented. The subject on chemical production has received less attention. This thesis describes and evaluates the quest for an alternative conversion route, based on a biomass feedstock and employing a heterogeneous catalyst capable of converting the feedstock, to a value-added chemical...

Bioenergy Research Programme. Yearbook 1994. Production of wood fuels

International Nuclear Information System (INIS)

Alakangas, E.

1995-01-01

BIOENERGIA Research Programme is one of energy technology programmes of the Finnish Ministry of Trade and Industry (in 1995 TEKES, Technology Development Center). The aim of Bioenergy Research Programme is to increase the use of economically profitable and environmentally sound bioenergy by improving the competitiveness of present peat and wood fuels. Research and development projects will also develop new economically competitive biofuels and new equipment and methods for production, handling and using of biofuels. The funding for 1994 was nearly 50 million FIM and projects numbered 60. The main goal of the production of wood fuels research area is to develop new production methods in order to decrease the production costs to the level of imported fuels. The total potential of the wood fuel use should be at least 1.0 million toe/a (5.5 million m 3 ). There were 27 projects in 1994 for research on wood fuel production. This part of the yearbook 1994 presents the main results of these projects. The wood reserves do not limit the obtainability of the target. Research and development work has, however, directed to development of equipment and research on wood fuels production chains. Many devices, designed for both separate and integrated production of wood fuels became ready or were becoming ready for prototyping, to be used for production tests. Results of the biomass harvesting and properties research were obtained for utilization in 1994. According to the results it is possible to obtain the desired targets both in integrated and separated production of wood fuels. (author)

Value-added beef products (Productos Carnicos con Valor Agregado)

Science.gov (United States)

Mac Donaldson; Will Holder; Jan Holder

2006-01-01

I'm speaking for Will and Jan Holder, who couldn't be here. I happen to be familiar with Will and Jan's company, Ervin's Natural Beef, and its program because I've sold them cattle. Will and Jan's value-added beef program is based on their family ranch in the area known as The Blue, in the mountains of eastern Arizona.

Constructing an allocation factor based on product and process related parameters to assess environmental burdens of producing value-added sludge-based products

OpenAIRE

Pradel, M.; Aissani, L.; Canler, J.C.; Roux, J.C.; Villot, J.; Baudez, J.C.; Laforest, V.

2018-01-01

Sludge is slowly moving away from providing basic by-products and towards providing value-added products (e.g. fertilisers); therefore, it is no longer perceived as waste but as a product. Consequently, wastewater treatment plants become multifunctional systems that produce two coproducts that are given a second life: sludge and "clean" water. An allocation factor in Life Cycle Assessment can partition environmental burdens of wastewater treatment between these two products, but doing so rema...

A synthesis of research on wood products and greenhouse gas impacts

International Nuclear Information System (INIS)

Sathre, R.; O'Connor, J.

2008-11-01

Existing scientific literature on the wood products industry was reviewed in an effort to summarize consensus findings, or range of findings, addressing the net life cycle greenhouse gas footprint of wood construction products. The report sought to clarify whether actively managing forests for wood production was better, worse or neutral for climate change than leaving the forest in its natural state. In addition, it sought to quantify the greenhouse gas emissions avoided per unit of wood substituted for non-wood materials. Forty-eight international studies were examined in terms of fossil energy used in wood manufacturing and compared alternatives, such as the avoidance of industrial process carbon emissions as with cement manufacturing; the storage of carbon in forests and forest products; the use of wood by-products as a biofuel replacement for fossil fuels; and carbon storage and emission due to forest products in landfills. The report presented a list of studies reviewed and individual summaries of study findings. A meta-analysis of displacement factors of wood product use was also presented. It was concluded from all of the studies reviewed, that the production of wood-based materials and products results in less greenhouse gas emission than the production of functionally comparable non-wood materials and products. 48 refs., 1 tab.

Multi-Angle Snowflake Camera Value-Added Product

Energy Technology Data Exchange (ETDEWEB)

Shkurko, Konstantin [Univ. of Utah, Salt Lake City, UT (United States); Garrett, T. [Univ. of Utah, Salt Lake City, UT (United States); Gaustad, K [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-12-01

The Multi-Angle Snowflake Camera (MASC) addresses a need for high-resolution multi-angle imaging of hydrometeors in freefall with simultaneous measurement of fallspeed. As illustrated in Figure 1, the MASC consists of three cameras, separated by 36°, each pointing at an identical focal point approximately 10 cm away. Located immediately above each camera, a light aims directly at the center of depth of field for its corresponding camera. The focal point at which the cameras are aimed lies within a ring through which hydrometeors fall. The ring houses a system of near-infrared emitter-detector pairs, arranged in two arrays separated vertically by 32 mm. When hydrometeors pass through the lower array, they simultaneously trigger all cameras and lights. Fallspeed is calculated from the time it takes to traverse the distance between the upper and lower triggering arrays. The trigger electronics filter out ambient light fluctuations associated with varying sunlight and shadows. The microprocessor onboard the MASC controls the camera system and communicates with the personal computer (PC). The image data is sent via FireWire 800 line, and fallspeed (and camera control) is sent via a Universal Serial Bus (USB) line that relies on RS232-over-USB serial conversion. See Table 1 for specific details on the MASC located at the Oliktok Point Mobile Facility on the North Slope of Alaska. The value-added product (VAP) detailed in this documentation analyzes the raw data (Section 2.0) using Python: images rely on OpenCV image processing library and derived aggregated statistics rely on some clever averaging. See Sections 4.1 and 4.2 for more details on what variables are computed.

Solid phase bio-electrofermentation of food waste to harvest value-added products associated with waste remediation.

Science.gov (United States)

Chandrasekhar, K; Amulya, K; Mohan, S Venkata

2015-11-01

A novel solid state bio-electrofermentation system (SBES), which can function on the self-driven bioelectrogenic activity was designed and fabricated in the laboratory. SBES was operated with food waste as substrate and evaluated for simultaneous production of electrofuels viz., bioelectricity, biohydrogen (H2) and bioethanol. The system illustrated maximum open circuit voltage and power density of 443 mV and 162.4 mW/m(2), respectively on 9 th day of operation while higher H2 production rate (21.9 ml/h) was observed on 19th day of operation. SBES system also documented 4.85% w/v bioethanol production on 20th day of operation. The analysis of end products confirmed that H2 production could be generally attributed to a mixed acetate/butyrate-type of fermentation. Nevertheless, the presence of additional metabolites in SBES, including formate, lactate, propionate and ethanol, also suggested that other metabolic pathways were active during the process, lowering the conversion of substrate into H2. SBES also documented 72% substrate (COD) removal efficiency along with value added product generation. Continuous evolution of volatile fatty acids as intermediary metabolites resulted in pH drop and depicted its negative influence on SBES performance. Bio-electrocatalytic analysis was carried out to evaluate the redox catalytic capabilities of the biocatalyst. Experimental data illustrated that solid-state fermentation can be effectively integrated in SBES for the production of value added products with the possibility of simultaneous solid waste remediation. Copyright © 2015 Elsevier Ltd. All rights reserved.

ECONOMIC VALUE ADDED AND MARKET VALUE ADDED - MODERN INDICATORS FOR ASSESSMENT THE FIRM’S VALUE

Directory of Open Access Journals (Sweden)

NICOLAE SICHIGEA

2015-12-01

Full Text Available The financial theory developed different categories of indicators - traditional and modern - in order to evaluate the firm’s value creation. The shareholders are directly interested by the value added in the company. The value creation is a complex process that implies correct decisions, common responsibility (managers and shareholders and actions towards an efficient and profitable activity. The traditional indicators of performance are not teoritically correlated with the the value creation and in these circumstances, should be used appropriate financial indicators in order to reflect the value of the company. Therefore, the modern indicators used in the value based management framework offer a greater flexibility and efficiency and represent a good alternative for companies. Such performance indicators used to measure the financial results correlated with shareholder wealth are the Economic Value Added (EVA, as a measure of internal performance and the Market Value Added (MVA as a measure of external performance of the company. Starting from the main deficiencies of the accounting indicators, the objective of this this study is to present the relationship between EVA and MVA and their implications on firms’valuation. Thus, the presentation and analysis of these indicators – EVA and MVA - will underline the main features, their correlations, and influence factors but also the main advantage and disadvantage of each indicator, which will enable the managers to make the correct choice and subsequently the best decision regarding the performance measures.

Perceptions Towards Non-Value-Adding Activities During The Construction Process

Directory of Open Access Journals (Sweden)

Ismail Haryati

2016-01-01

Full Text Available Non-value-adding activities are pure waste during the construction process. However, most of the construction practitioner does not realise that most of the activities performed during the construction process add no value to their project. A total of 375 numbers of questionnaires distributed to the Developer, Jabatan Kerja Raya, Consultants and Contractors. The study found that awareness by construction participants in Malaysia to take actions against non-value-adding activities during the construction process is relatively low. Through analysed by using the Pareto Chart, it has been found that defects and waiting time are two categories of non-value-adding activities that need to be prioritised by the industry. It is also found that non-value-adding activities most frequently occurred during structural and architectural work. This paper also reviewed on the causes of non-value-adding activities and discussed its effect towards time, cost, quality and productivity of the construction project. This paper is also important to give clearness and broader understandings on this form of waste other than material waste.

The value chain of small-sized energy wood

Energy Technology Data Exchange (ETDEWEB)

Karttunen, K.; Foehr, J.; Ranta, T. (Lappeenranta Univ. of Technology, Mikkeli (Finland), LUT Energy), Email: kalle.karttunen@lut.fi, Email: jarno.fohr@lut.fi, Email: tapio.ranta@lut.fi; Ahtikoski, A. (The Finnish Forest Research Institute, Rovaniemi (Finland)), Email: anssi.ahtikoski@metla.fi; Valsta, L. (Helsinki Univ. (Finland), Dept. of Forest Economics), Email: lauri.valsta@helsinki.fi

2009-07-01

Finland has agreed to increase the share of renewable energy to the level of 38% by the end of 2020. Most of the increase is to be based on bioenergy. According to the National Climate and Energy Strategy, the need for forest biomass will come to more than 20 TWh, or some 10 million cubic meters per year. Energy wood from young stand thinnings are the biomass resource with the most potential at the moment. The purpose of this study was to compare cost differences between forest management incorporating energy wood thinning and forest management based on traditional roundwood thinning. In addition, alternative supply chain costs for small-sized wood were studied. The results of the study show that it is worth considering the following points if the demand and average price for forest chips remain high. 1. Forest-owners: Forest management including energy wood thinning is financially feasible. 2. Supply chain: A terminal chipping chain enables large-scale procurement of small-sized energy wood. 3. Power plants: Currently, subsidies, emission trading, and decreasing pulpwood prices together enable large-scale use of small-sized wood for energy purposes. The value chain of small-sized energy wood in large-scale power plants could be mobilised. (orig.)

Implementation of new technologies in wood industry and their effect in wood products quality

OpenAIRE

ELVA ÇAUSHI; PANDELI MARKU

2014-01-01

There are about 300 companies producing furniture and about 250 small and medium enterprises (SME) producing sawn timber, which operate in the field of wood industry in Albania. This wood industry production is being challenged by the increasing demand in the domestic market, ranging from kitchen furniture to office and schools furniture, bedroom furniture, doors, windows, and saw timber in different dimensions. The production from the wood industry can fulfill about 80% of the domestic mark...

Understanding key issues of sustainable wood production in the Pacific Northwest.

Science.gov (United States)

Robert L. Deal; Seth M. White

2005-01-01

Researchers involved with the Pacific Northwest (PNW) Research Station Sustainable Wood Production Initiative have outlined some of the barriers and opportunities for sustainable wood production in the region. Sustainable wood production is defined as the capacity of forests to produce wood, products, and services on a long-term basis and in the context of human...

2009 Wood and Fiber Product Seminar : VTT and USDA joint activity

Science.gov (United States)

Ali Harlin; Minna Vikman

2010-01-01

Foward -- The development of high-value wood and fiber products is one of the most important challenges currently facing the forest industry. Traditional pulp and paper products are on a critical path in developed countries with prices and markets decreasing. Finland and the USA have faced the same problem, which is a fundamental reason for Industrial Biomaterials...

Integrated microbial processes for biofuels and high value-added products: the way to improve the cost effectiveness of biofuel production.

Science.gov (United States)

da Silva, Teresa Lopes; Gouveia, Luísa; Reis, Alberto

2014-02-01

The production of microbial biofuels is currently under investigation, as they are alternative sources to fossil fuels, which are diminishing and their use has a negative impact on the environment. However, so far, biofuels derived from microbes are not economically competitive. One way to overcome this bottleneck is the use of microorganisms to transform substrates into biofuels and high value-added products, and simultaneously taking advantage of the various microbial biomass components to produce other products of interest, as an integrated process. In this way, it is possible to maximize the economic value of the whole process, with the desired reduction of the waste streams produced. It is expected that this integrated system makes the biofuel production economically sustainable and competitive in the near future. This review describes the investigation on integrated microbial processes (based on bacteria, yeast, and microalgal cultivations) that have been experimentally developed, highlighting the importance of this approach as a way to optimize microbial biofuel production process.

EVALUATION OF BIOETHANOL PRODUCTION FROM Eucalyptus WOOD WITH Saccharomyces cerevisiae AND SACSV-10 1

Directory of Open Access Journals (Sweden)

Sylvia Enid Vazquez

2018-04-01

Full Text Available ABSTRACT Eucalyptus spp. residues of paper industry are a potential lignocellulosic raw material for production of second-generation bioethanol as an alternative to conventional production from cereal crops. Studying the behavior at 40 ºC of a commercial cellulase (Sunson, Eucalyptus sawdust saccharification was carried out under two pH conditions. With the aim to evaluate the bioethanol production from Eucalyptus wood, a strategy combining saccharification and Simultaneous Saccharification and Fermentation (SSF was undertaken at 40 ºC with a thermotolerant Saccharomyces cerevisiae with different substrate and inoculum concentrations, and different nitrogen sources. At last, the process was carried out in optimal conditions with Saccharomyces cerevisiae M522 and SacSV-10. Saccharification produced more free glucose at pH 5, reaching a maximum of 1.5 g/L. Encouraging results were obtained with 500 mg/L of ammonium sulphate as a nitrogen source and 10 % v/v initial inoculum at 106 cfu/mL concentration. Yeast SacSV-10 was not inhibited by phenols present in the culture media using a wood concentration of 10 g/L, but when the solids concentration was increased, the bioprocess yield was compromised. When the process was carried out in optimal conditions the bioethanol production, expressed as the conversion percentage of cellulose to ethanol, was 71.5 % and 73.6 % for M522 and the mutant strain respectively. The studied properties of the mutant strain provide added value to it, which pose new challenges to national companies dedicated to the production and sale of inputs for bioethanol industry.

Eucalyptus wood and coffee parchment for particleboard production: Physical and mechanical properties

Directory of Open Access Journals (Sweden)

Mário Vanoli Scatolino

Full Text Available ABSTRACT The wood panel industry is constantly growing, being necessary the innovation in technologies and raw materials to improve the quality of the final product. Considering the shortage and pressure to decrease the dependence of wood, there is an interest in other renewable materials such as agricultural wastes. Among these wastes, coffee parchment is one which deserves notoriety. An alternative use for coffee parchment could be for production of particleboard in association with wood particles. This study aimed to evaluate the feasibility of using coffee parchment for production of particleboard. The following percentages of wastes were used: 0, 10, 20, 30, 40 and 50% in association to eucalyptus wood. The panels were produced with 8% of urea formaldehyde (based on dry weight of particles. The pressing cycle consisted by: pre-pressing of 0.5 MPa for 10 minutes followed by pressing of 4.0 MPa, and temperature of 160° C for 15 minutes. The compaction ratio of particleboards produced using higher quantities of parchment improved the physical properties. The properties of Water Absorption (2 and 24 h and Thickness Swelling (2 h decreased with increasing percentage of coffee parchment. The Thickness Swelling (24 h showed not significant effect with an increase of coffee waste. The Modulus of Elasticity for coffee parchment particleboards was in the range 646.49 ± 112.65 to 402.03 ± 66.24 MPa, while the Modulus of Rupture ranged from 8.18 ± 1.39 to 4.45 ± 0.75 MPa. The results showed that 10% of coffee parchment could be added for production of particleboards.

Design considerations for the commercial production of wood acrylics

International Nuclear Information System (INIS)

Witt, A.E.; Bosco, L.R.

1978-01-01

The major application of wood acrylics is for flooring, more specifically in high traffic area. The most important property is its abrasion resistance. As for the decisions in facility design, the following considerations must be made: irradiation or heat-catalyst to polymerize, machine irradiation or isotope irradiation, and wet or dry irradiation. Then, processing considerations are made on wood type, monomer selection, dye selection, fire retardant, dose conditions and crosslinker usage. In ''PermaGrain'' production, for example, the facility has the yearly production capacity of over 4,000,000 kilograms of wood acrylic. The starting wood form is small slats or fingers. After pressure cycle, the impregnant wet wood is lowered into an irradiation pool and the product canister passes around a cobalt 60 source. After irradiation, the product is taken out of the pool and allowed to cool. Then, final sizing and finishing are carried out. (Mori, K.)

DESIRABLE ATTRIBUTES FOR VALUE ADDED MEAT PRODUCTS SURVEY 1993

OpenAIRE

Kinsey, Jean D.; Senauer, Benjamin; Jonk, Yvonne

1993-01-01

The purpose of this consumer survey was to learn more about consumer preferences for meat characteristics. Value added meat processors faced with the problem of trying to identify market niches wanted to know what types of consumers had similar preferences and what their specific preferences and concerns are. In addition, we wanted to learn more about attitudes that are believed to be changing due to new information about the relationship between diet and long term health, lifestyles that dem...

The Role and Implications of the Added Value as an Indicator of Financial Performance

Directory of Open Access Journals (Sweden)

Cornelia Tureac

2014-02-01

Full Text Available The added value represents the excess of income over the value of consumptions coming from third parties, respectively the wealth created by capitalizing the technical, human and financial resources of the company. The economy is an established running after the optimal decision; so there cannot exist and economy without leadership, so there cannot be leadership without analysis, respectively the analysis of added value. This paper deals with a comparative analysis of three years, ie 2010 – 2012, of the added value from within Thomson Logistic Ltd which has 3 working points in Galati, Ploiesti and Targul Neamt. The analysis of added value is important both from the company‘s manager as an indicator for financial performance, and in terms of tax which is an indicator in the system of taxation. The methodology of this paper can be found in the use and application of the economical and financial analysis in order to perform an analysis of the added value that expresses the increase of wealth that is achieved through technical and productive activity. More specifically there were analyzed the added value, expenses of added value nature, structure of added value, growth indices of the corresponding elements of VA and the analysis from factorial point of view of the added value. In conclusion the growth rate of added value exceeded in dynamic the production value of the exercise (77.7>66.81; 31.21>31.17 because the intermediate consumption from third parties increased in 2011, and the added value decreases to an percentage of 22.30 % compared to the basis year in 2010. The result of exploitation had a decisive contribution to the decline in the added value, registering a drop of 88.05 % compared to 2011, respectively from 11705.2 Ron to 1399 Ron in 2012.

Wood products trade and foreign markets. Annual production, consumption, and trade issue. Principal countries impacting US trade in wood products. Foreign agriculture circular

International Nuclear Information System (INIS)

1993-05-01

The Forest Products Division has compiled production, consumption, and trade data on selected wood products for twenty eight significant countries. The data, collected from various sources, is not necessarily compatible with US export and import data normally published in this circular, which comes from the US Census Bureau. To supplement this data, the following perspectives offer a comparative snapshot of conditions in these countries, both in the general economy and the wood products sector. Economic information was extracted from the 1992 World Factbook; Central Intelligence Agency

Facilities Management and Added Value

DEFF Research Database (Denmark)

Jensen, Per Anker

2010-01-01

Aim: This paper aims to present different models of the concept of the added value of Facilities Management (FM), including the FM Value Map, which forms the basis of research group in EuroFM, and to present some of the results of this research collaboration. Approach and methodology: The paper...... is based on literature reviews of the most influential journals within the academic fields of FM, Corporate Real Estate Management and Business to Business Marketing and discussions between participants of the research group working on a further exploration and testing of the FM Value Map. Conclusions......: The research shows a number of different definitions and focus points of Added Value of FM, dependent on the academic field and the area of application. The different research perspectives explored a holistic view on the added value of FM by the integration of an external market based view (with a focus...

Adding more value to added-value

DEFF Research Database (Denmark)

Marian, Livia

Recent studies reveal that consumers respond favourably to “organic plus” products with additional ethical attributes. The aim of the current study is to explore whether consumers would notice and value further improvements in the animal welfare standards than those imposed by the organic...... regulation. The results of a qualitative concept test reveal positive attitudes towards the proposed production process. The discussions about fewer standards being sufficient or about options “in-between” conventional and organic standards indicate that the difference in production processes is noticed, yet...

Under What Circumstances Do Wood Products from Native Forests Benefit Climate Change Mitigation?

Directory of Open Access Journals (Sweden)

Heather Keith

Full Text Available Climate change mitigation benefits from the land sector are not being fully realised because of uncertainty and controversy about the role of native forest management. The dominant policy view, as stated in the IPCC's Fifth Assessment Report, is that sustainable forest harvesting yielding wood products, generates the largest mitigation benefit. We demonstrate that changing native forest management from commercial harvesting to conservation can make an important contribution to mitigation. Conservation of native forests results in an immediate and substantial reduction in net emissions relative to a reference case of commercial harvesting. We calibrated models to simulate scenarios of native forest management for two Australian case studies: mixed-eucalypt in New South Wales and Mountain Ash in Victoria. Carbon stocks in the harvested forest included forest biomass, wood and paper products, waste in landfill, and bioenergy that substituted for fossil fuel energy. The conservation forest included forest biomass, and subtracted stocks for the foregone products that were substituted by non-wood products or plantation products. Total carbon stocks were lower in harvested forest than in conservation forest in both case studies over the 100-year simulation period. We tested a range of potential parameter values reported in the literature: none could increase the combined carbon stock in products, slash, landfill and substitution sufficiently to exceed the increase in carbon stock due to changing management of native forest to conservation. The key parameters determining carbon stock change under different forest management scenarios are those affecting accumulation of carbon in forest biomass, rather than parameters affecting transfers among wood products. This analysis helps prioritise mitigation activities to focus on maximising forest biomass. International forest-related policies, including negotiations under the UNFCCC, have failed to recognize

Value adding management: A concept and a case

DEFF Research Database (Denmark)

Jensen, Per Anker; Katchamart, Akarapong

2012-01-01

be used more directly and proactively by facilities managers to implement adding value strategies and practices. Methodology: The development of the concept of Value Adding Management is based on the management model for FM included in the European FM standards, recent theories on added value of FM...... practice value adding management. It underlines the importance of stakeholder and relationship management as part of adding value. The case study confirms the relevance of the basic concept of Value Adding Management. Practical implications: The concept of Value Adding Management is expected to increase......Purpose: To develop a management concept that can assist facilities managers in implementing value adding strategies and practices. The FM Value Map has been developed to analyse and demonstrate the different ways FM can add value. However, there is a need to develop management tools that can...

Bio-energy in the wood processing industry. Manual for energy production from residual matter for the wood processing industry

International Nuclear Information System (INIS)

Van Halen, C.J.G.; Arninkhof, M.J.C.; Rommens, P.J.M.; Karsch, P.

2000-04-01

This manual is published within the framework of a project, financed by Novem (EWAB programme) and the European Commission (Altener programme). Similar manuals were drafted in Germany, England and Sweden. The basis of the project was the manual 'Quality manual for small-scale wood incineration and wood gasification', published by Novem in 1998. That quality manual was drafted on the basis of an evaluation of a number of wood combustion and wood gasification projects. The original manual has been improved as a result of comments made by experts in the field of bio-energy. Updated information was added with respect to legislation, financing options and new technology. Also the manual is focused more on the wood processing industry

British and German manufacturing productivity compared : A new benchmark for 1935/36 based on double deflated value added

NARCIS (Netherlands)

Fremdling, Rainer; de Jong, Herman; Timmer, Marcel P.

We present a new estimate of Anglo-German manufacturing productivity levels for 1935/36. It is based on archival data on German manufacturing and published British census data. We calculate comparative levels of value added, correcting for differences in prices for outputs and inputs. This so-called

AIP1OGREN: Aerosol Observing Station Intensive Properties Value-Added Product

Energy Technology Data Exchange (ETDEWEB)

Koontz, Annette [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Flynn, Connor [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2017-09-15

The aip1ogren value-added product (VAP) computes several aerosol intensive properties. It requires as input calibrated, corrected, aerosol extensive properties (scattering and absorption coefficients, primarily) from the Aerosol Observing Station (AOS). Aerosol extensive properties depend on both the nature of the aerosol and the amount of the aerosol. We compute several properties as relationships between the various extensive properties. These intensive properties are independent of aerosol amount and instead relate to intrinsic properties of the aerosol itself. Along with the original extensive properties we report aerosol single-scattering albedo, hemispheric backscatter fraction, asymmetry parameter, and Ångström exponent for scattering and absorption with one-minute averaging. An hourly averaged file is produced from the 1-minute files that includes all extensive and intensive properties as well as submicron scattering and submicron absorption fractions. Finally, in both the minutely and hourly files the aerosol radiative forcing efficiency is provided.

Environmental life cycle assessment of wood-based building materials and building product. Oekobilanzen von Baustoffen und Bauprodukten aus Holz; Zusammenfassung erster Erkenntnisse

Energy Technology Data Exchange (ETDEWEB)

Richter, K; Sell, J [Eidgenoessische Materialpruefungs- und Versuchsanstalt fuer Industrie, Bauwesen und Gewerbe, Duebendorf (Switzerland)

1992-08-01

This report presents a summary of the main studies on the topic carried out at EMPA wood department in the last 4 years.In its first part, the concept of an environmental life cycle analysis (LCA), whose purpose is to quantify the known environmental impacts of a product by means of a systematic input/output analysis, is described. Such evaluation must include all phases of a product's life cycle, from the extraction of resources to the final disposal. Raw material and energy supply are input values, whereas main products, by-products, and emissions to the environment are outputs. It is essential for a meaningful data collection as well as for the final interpretation of the results to define exact system boundaries and explain the models used for data aggregation which are, therefore, described in detail. The report's second part summarizes the results of an environmental assessment of wood as a raw material and construction component, and of some important wood-based products. First, some product-independent ecological values of wood are shown, which today cannot be quantified sufficiently in LCA (e.g. relations between forest management and multi-functional values of forests, sustainable reproduction of wood, careful and benign harvesting practices, CO[sub 2] cycling with wood, and the complete utilization of the resource for industrial productions). Although all these basic characteristics contribute to the out-standing ecologic value of wood, an environmental analysis has to concentrate on material- and product-related aspects. In our study, this is realized by assessing energy consumption and air pollution. In a case study the data compiled are used to compare a timber frame wall with several wall types of different materials, but with identical heat transmission and acoustic performance: as expected, the timber frame wall shows very good ratings. (author) figs., tabs., 21 refs.

Trends in the highway market for wood products

Science.gov (United States)

Robert G. Knutson

1975-01-01

Forty-eight million cubic feet of wood products, about 50 million dollars worth, were used in the Nation's highway construction program in 1972. Expenditures for highway construction increased 2½ times from 1954 to 1972. The volume of wood products used in highway construction changed little during this period because other materials were substituted for...

Characterization of Cypress Wood for Kraft Pulp Production

Directory of Open Access Journals (Sweden)

António J. A. Santos

2014-06-01

Full Text Available Wood samples of Cupressus arizonica, C. lusitanica, and C. sempervirens were evaluated for chemical, anatomical, and pulp characteristics as raw material for pulp production. Two 17-year-old trees per species were harvested, and wood samples were taken at a height of 2 m. Wood chips from Pinus pinaster (Portugal and P. sylvestris (Finland were used as references. C. arizonica differed from C. lusitanica and C. sempervirens with significantly lower (p < 0.05 tracheid diameter and wall thickness in the earlywood. The total extractives contents were 3.9%, 3.3%, and 2.5% for C. lusitanica, C. sempervirens, and C. arizonica, respectively, lower than the 5.1% for P. pinaster and 4.5% for P. sylvestris. Klason lignin content ranged from 33.0 to 35.6%, higher than the 28.0 to 28.7% for the pinewoods. The kraft pulp yields for C. arizonica, C. lusitanica, and C. sempervirens were 37.7%, 36.7%, and 38.7%, respectively, with kappa numbers of 32.0, 31.6, and 28.7, respectively; the yield values were 40.8% and 42.8%, with kappa numbers of 23.4 and 21.0, for P. pinaster and P. sylvestris, respectively. The cypress species are clearly different from pine in relation to wood pulping behavior. Among the cypress, C. sempervirens provided the best pulping results.

A Closer Look at Revealed Comparative Advantage: Gross-versus Value Added Trade Flows

OpenAIRE

Brakman, Steven; van Marrewijk, Charles

2015-01-01

With the availability of international value added trade data it has become evident that gross export data and value added data do not provide the same information. Although gross exports crosses national borders and is the target of trade policy, value added data tell us what fragment in the production chain is internationally competitive in a particular country. With respect to comparative advantage the differences between the two types of data are often illustrated by means of examples usi...

Lignocellulosic biorefinery as a model for sustainable development of biofuels and value added products.

Science.gov (United States)

De Bhowmick, Goldy; Sarmah, Ajit K; Sen, Ramkrishna

2018-01-01

A constant shift of society's dependence from petroleum-based energy resources towards renewable biomass-based has been the key to tackle the greenhouse gas emissions. Effective use of biomass feedstock, particularly lignocellulosic, has gained worldwide attention lately. Lignocellulosic biomass as a potent bioresource, however, cannot be a sustainable alternative if the production cost is too high and/ or the availability is limited. Recycling the lignocellulosic biomass from various sources into value added products such as bio-oil, biochar or other biobased chemicals in a bio-refinery model is a sensible idea. Combination of integrated conversion techniques along with process integration is suggested as a sustainable approach. Introducing 'series concept' accompanying intermittent dark/photo fermentation with co-cultivation of microalgae is conceptualised. While the cost of downstream processing for a single type of feedstock would be high, combining different feedstocks and integrating them in a bio-refinery model would lessen the production cost and reduce CO 2 emission. Copyright © 2017 Elsevier Ltd. All rights reserved.

Using wood products to mitigate climate change: External costs and structural change

Energy Technology Data Exchange (ETDEWEB)

Sathre, Roger; Gustavsson, Leif [Ecotechnology, Mid Sweden University, 831 25 Oestersund (Sweden)

2009-02-15

In this study we examine the use of wood products as a means to mitigate climate change. We describe the life cycle of wood products including forest growth, wood harvest and processing, and product use and disposal, focusing on the multiple roles of wood as both material and fuel. We present a comparative case study of a building constructed with either a wood or a reinforced concrete frame. We find that the production of wood building material uses less energy and emits less carbon than the production of reinforced concrete material. We compare the relative cost of the two building methods without environmental taxation, under the current Swedish industrial energy taxation regime, and in scenarios that incorporate estimates of the full social cost of carbon emission. We find that the inclusion of climate-related external costs improves the economic standing of wood construction vis-a-vis concrete construction. We conclude that policy instruments that internalise the external costs of carbon emission should encourage a structural change toward the increased use of sustainably produced wood products. (author)

Women's work... in wood products

Science.gov (United States)

Janice K. Wiedenbeck

1998-01-01

Women have opportunities galore in the 1990s in wood products research, education, extension, consulting,manufacturing, marketing, and associations in North America. In the 1980s the same statement could not have been made.

Competitiveness of wood pulp production in different Brazilian states

Directory of Open Access Journals (Sweden)

Naisy Silva Soares

2013-06-01

Full Text Available This work aimed to analyze the competitiveness of wood pulp production in different Brazilian states, in May, 2008 (Minas Gerais, São Paulo, Espírito Santo and Bahia, using the Policy Analysis Matrix (PAM. The results obtained indicated that the private and social profitability of wood pulp production and commercialization was positive and greater in Bahia. The Brazilian companies were penalized by public policies adopted for the sector; the wood pulp production in São Paulo and Bahia were more competitive and less exposed to the negative effects of public policies that reduce the national company profits.

Ιnvestment in green economy as a potential source of value added

Directory of Open Access Journals (Sweden)

Jan Klasinc

2015-12-01

Full Text Available Purpose - The hypothesis of the paper is that domestic value added created by exports in Croatia could be increased by investments in green economy. Methodology - In the developed economies only specific products, processes and functions that outperform emerging economies in Global Value Chains are able to profit from the larger share of value added. Large portion of "green economy" is knowledge intensive, and if knowledge based economy (KBC plays a significant role in determining the domestic value added created by exports, economies with a larger stock of KBC should have a larger difference in VAX between knowledge-intensive industries and less knowledge-intensive industries. Domestic value added embodied in exports can be proxied by attracted FDI. Findings - The results seem to show some support to the hypothesis. In Croatia it has already been shown that sectors of economy with larger stock of intellectual capital measured by Intellectual Capital Efficiency (ICE index attracted more FDI, which can also serve as a predictor for larger value added in exports due to higher productivity. Knowledge intensity of 18 industries in the US as the benchmark economy shows that "Electrical and optical equipment" has above average knowledge intensity of 0,53, and it can be matched with "green economy" in Croatian industries that attracted more FDI and have higher levels of KBC. Research limitations and implications - Although this study is limited just to KBC, as an extension, the potential role of financial development could be included. Also, the length of time series for VAX measured by OECD does not allow for more thorough analysis. Originality/value – Although not conclusive, this paper is an important first step giving direction to subsequent studies of effects of KBC on value added.

5000 sustainable workplaces - Wood energy provides work

International Nuclear Information System (INIS)

Keel, A.

2009-01-01

This article presents the results of a study made by the Swiss Wood Energy Association on the regional and national added value resulting from large wood-fired installations in Switzerland. The number of workplaces created by these installations is also noted. Wood energy is quoted as not only being a way of using forest wastes but also as being a creator of employment. Large wood-fired heating installations are commented on and efforts to promote this type of energy supply even further are discussed. The study indicates which professions benefit from the use of wood energy and quantifies the number of workplaces per megawatt of installed power that result.

Simulated long-term effects of varying tree retention on wood production, dead wood and carbon stock changes.

Science.gov (United States)

Santaniello, Francesca; Djupström, Line B; Ranius, Thomas; Weslien, Jan; Rudolphi, Jörgen; Sonesson, Johan

2017-10-01

Boreal forests are an important source of timber and pulp wood, but provide also other products and services. Utilizing a simulation program and field data from a tree retention experiment in a Scots pine forest in central Sweden, we simulated the consequences during the following 100 years of various levels of retention on production of merchantable wood, dead wood input (as a proxy for biodiversity), and carbon stock changes. At the stand level, wood production decreased with increased retention levels, while dead wood input and carbon stock increased. We also compared 12 scenarios representing a land sharing/land sparing gradient. In each scenario, a constant volume of wood was harvested with a specific level of retention in a 100-ha landscape. The area not needed to reach the defined volume was set-aside during a 100-year rotation period, leading to decreasing area of set-asides with increasing level of retention across the 12 scenarios. Dead wood input was positively affected by the level of tree retention whereas the average carbon stock decreased slightly with increasing level of tree retention. The scenarios will probably vary in how they favor species preferring different substrates. Therefore, we conclude that a larger variation of landscape-level conservation strategies, also including active creation of dead wood, may be an attractive complement to the existing management. Copyright © 2017 Elsevier Ltd. All rights reserved.

Users guide for WoodCite, a product cost quotation tool for wood component manufacturers [computer program

Science.gov (United States)

Jeff Palmer; Adrienn Andersch; Jan Wiedenbeck; Urs. Buehlmann

2014-01-01

WoodCite is a Microsoft® Access-based application that allows wood component manufacturers to develop product price quotations for their current and potential customers. The application was developed by the U.S. Forest Service and Virginia Polytechnic Institute and State University, in cooperation with the Wood Components Manufacturers Association.

Energy wood. Part 2b: Wood pellets and pellet space-heating systems

International Nuclear Information System (INIS)

Nussbaumer, T.

2002-01-01

The paper gives an overview on pellet utilization including all relevant process steps: Potential and properties of saw dust as raw material, pellet production with drying and pelletizing, standardization of wood pellets, storage and handling of pellets, combustion of wood pellets in stoves and boilers and applications for residential heating. In comparison to other wood fuels, wood pellets show several advantages: Low water content and high heating value, high energy density, and homogeneous properties thus enabling stationary combustion conditions. However, quality control is needed to ensure constant properties of the pellets and to avoid the utilization of contaminated raw materials for the pellet production. Typical data of efficiencies and emissions of pellet stoves and boilers are given and a life cycle analysis (LCA) of wood pellets in comparison to log wood and wood chips is described. The LCA shows that wood pellets are advantageous thanks to relatively low emissions. Hence, the utilization of wood pellet is proposed as a complementary technology to the combustion of wood chips and log wood. Finally, typical fuel cost of wood pellets in Switzerland are given and compared with light fuel oil. (author)

Pengukuran Kinerja Perusahaan Melalui Economic Value Added (Eva) Dan (Mva) Market Value

OpenAIRE

Andhaniwati, Erry

2011-01-01

Performance corporating to constitute one of prescriptive factor gets on descent of stock price because firm performance constitute to refuse fathom for investor deeping to determine stock bid price. Economic Value Added, and Market Value Added are umpteen corporate performance grader that can be utilized by investor in assesses how well firm performance. Therefore to the effect this research is subject to be analyse influence among Economic Value Added , and Market Value Added to stock pr...

Wood Flour Moulding Technology: Implications for Technical ...

African Journals Online (AJOL)

The intent of this article is to demonstrate how wood waste called sawdust or wood flour can be transformed by plastic moulding machine into items of economic value. Wood flour is wood reduced to very fine particle form. It can be waste product from saw mills, wood working plants or produced from selected dry wood by ...

IS THE VALUE ADDED TAX A SUPERIOR SALES TAX IN ALL SALES TAXES?

Directory of Open Access Journals (Sweden)

MUSTAFA ALİ SARILI

2013-05-01

Full Text Available Value Added Tax (VAT is a tax imposed on the value added to a product at each stage of the production and distribution process. Value added is never taxed twice under VAT and thus cascading (tax on tax effects do not occur. It is a single tax on goods and services but the tax is collected multiple stages. At each of these stages, the amount of tax payable is computed by subtracting the tax previously paid on purchases from the tax charged on sales by the traders for each taxation period. In last three decades, VAT, a relatively new and better commodity taxation, has been introduced in many countries. It has replaced different types of sales taxes in such countries. This article attempts to evaluate VAT by comparing with other sales taxes.

Air quality and composite wood products

Science.gov (United States)

Melissa G. D. Baumann

1999-01-01

Research at the USDA Forest Service, Forest Products Laboratory (FPL) is being conducted to identify the compounds emitted from wood products during their manufacture and subsequent use. The FPL researchers are measuring the types and quantities of VOCs that are emitted from particleboard and MDF products to provide quantitative emissions information. This information...

What is the current state of forest product markets and how will they develop in the future?

Science.gov (United States)

Ragnar Jonsson; Elias Hurmekoski; Lauri Hetemaki; Jeffrey Prestemon

2017-01-01

Forest-based industries – pulp and paper, solid wood products, and a number of downstream value-added wood-based manufacturers – have received limited attention in the pursuit of a successful implementation of EU and national bioeconomy strategies. According to Eurostat, the pulp and paper and solid wood products industries accounted for about 4.4% (€277 billion) of...

Wood chip production technology and costs for fuel in Namibia

Energy Technology Data Exchange (ETDEWEB)

Leinonen, A.

2007-12-15

This work has been done in the project where the main target is to evaluate the technology and economy to use bush biomass for power production in Namibia. The project has been financed by the Ministry for Foreign Affairs of Finland and the Ministry of Agriculture, Water and Forestry of the Republic of Namibia. The target of this study is to calculate the production costs of bush chips at the power plant using the current production technology and to look possibilities to develop production technology in order to mechanize production technology and to decrease the production costs. The wood production costs are used in feasibility studies, in which the technology and economy of utilization of wood chips for power generation in 5, 10 and 20 MW electric power plants and for power generation in Van Eck coal fired power plant in Windhoek are evaluated. Field tests were made at Cheetah Conservation Farm (CCF) in Otjiwarongo region. CCF is producing wood chips for briquette factory in Otjiwarongo. In the field tests it has been gathered information about this CCF semi-mechanized wood chip production technology. Also new machines for bush biomass chip production have been tested. A new mechanized production chain has been designed on the basis of this information. The production costs for the CCF semi-mechanized and the new production chain have been calculated. The target in the moisture content to produce wood chips for energy is 20 w-%. In the semi-mechanized wood chip production chain the work is done partly manually, and the supply chain is organized into crews of 4.8 men. The production chain consists of manual felling and compiling, drying, chipping with mobile chipper and manual feeding and road transport by a tractor with two trailers. The CCF production chain works well. The chipping and road transport productivity in the semimechanized production chain is low. New production machines, such as chainsaw, brush cutter, lawn mover type cutter, rotator saw in skid

Bioconversion of garden waste, kitchen waste and cow dung into value-added products using earthworm Eisenia fetida.

Science.gov (United States)

Wani, K A; Mamta; Rao, R J

2013-04-01

Solid waste management is a worldwide problem and it is becoming more and more complicated day by day due to rise in population, industrialization and changes in our life style. Transformation of industrial sludges into vermicompost is of double interest: on the one hand, a waste is converted into value added product, and, on the other, it controls a pollutant that is a consequence of increasing industrialization. Garden waste, kitchen waste and cow dung were subjected to recycle through vermicomposting by using the epigeic earthworm Eisenia fetida under field conditions. The pH, moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium in vermicompost was analysed. It was found that moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium was high in cow dung, followed by kitchen waste and garden waste. This study clearly indicates that vermicomposting of garden waste, kitchen waste and cow dung can not only produce a value added produce (vermicomposting) but at the same time reduce the quantity of waste.

Value Adding Management: A New Facilities Management Concept

DEFF Research Database (Denmark)

Jensen, Per Anker; Katchamart, Akarapong

2011-01-01

Purpose: To investigate how Facilities Management (FM) can add value and develop a management concept that can assist facilities managers in implementing value adding strategies and practices. Theory: The study is based on the management model for FM included in the European FM standards, recent...... is investigated, tested and discussed based on a case study of an international corporation. Findings: The study shows that the management model for FM creates a relevant starting point but also that stakeholder and relationship management is an essential aspect of Value Adding Management. The case study confirms...... the relevance of the basic concept and provides an important example of how Value Adding Management can be implemented and added value measured. Originality/value: The study develops a concept of Value Adding Management, which is new in FM literature. It is expected to increase the awareness of the impacts...

NIR techniques create added values for the pellet and biofuel industry.

Science.gov (United States)

Lestander, Torbjörn A; Johnsson, Bo; Grothage, Morgan

2009-02-01

A 2(3)-factorial experiment was carried out in an industrial plant producing biofuel pellets with sawdust as feedstock. The aim was to use on-line near infrared (NIR) spectra from sawdust for real time predictions of moisture content, blends of sawdust and energy consumption of the pellet press. The factors varied were: drying temperature and wood powder dryness in binary blends of sawdust from Norway spruce and Scots pine. The main results were excellent NIR calibration models for on-line prediction of moisture content and binary blends of sawdust from the two species, but also for the novel finding that the consumption of electrical energy per unit pelletized biomass can be predicted by NIR reflectance spectra from sawdust entering the pellet press. This power consumption model, explaining 91.0% of the variation, indicated that NIR data contained information of the compression and friction properties of the biomass feedstock. The moisture content model was validated using a running NIR calibration model in the pellet plant. It is shown that the adjusted prediction error was 0.41% moisture content for grinded sawdust dried to ca. 6-12% moisture content. Further, although used drying temperatures influenced NIR spectra the models for drying temperature resulted in low prediction accuracy. The results show that on-line NIR can be used as an important tool in the monitoring and control of the pelletizing process and that the use of NIR technique in fuel pellet production has possibilities to better meet customer specifications, and therefore create added production values.

Integrated production of wood fuel and pulp wood from young stands; Integroitujen tuotantomenetelmien vertailu

Energy Technology Data Exchange (ETDEWEB)

Korpilahti, A [Metsaeteho Oy, Helsinki (Finland)

1997-12-01

The aim of the study was to clarify the competitiveness of different harvesting chains and processing methods of first thinning wood. Great expectations have been laid on integrated production of wood fuel and pulp wood. Results produced in other bioenergy projects were taken into account, and in this project some field experiments on mechanised felling-bunching and compressing of the load of tree sections during forwarding were carried out. The new processing methods, the MASSAHAKE-method and chain-flail delimbing combined with small-scale drum debarking, still are under development giving a rather unstable data for comparisons. Both in pine and birch dominant stands modern multiple tree logging gave the most favourable results when ranking on the bases of the price of pulp chips. Integrated methods were not very far and they have more potential than methods based on harvesting delimbed short wood. When compared on the bases of the production cost of pulp, integrated methods were in general the most favourable because they give good subsidies on the form of bioenergy. (orig.)

Economic value added or earnings: What explains market value in Indian firms?

Directory of Open Access Journals (Sweden)

Nufazil Altaf

2016-12-01

Full Text Available The purpose of this paper is to empirically test the claim made by Stern Stewart & Company that economic value added is a better metric that traditional earning based measures in explaining market value. For better exposition, a sample of 325 Indian firms has been divided into two parts- 170 firms belonging to Indian manufacturing companies and 155 companies belonging to the Indian service sector. After performing univariate and multivariate regression analyses, the results of the study reveal that the operating income has a strong linkage with market value added in both manufacturing and service sectors. For both the sectors, the economic value added shows weaker but positive relationship with the market value added.

Metrix Matrix: A Cloud-Based System for Tracking Non-Relative Value Unit Value-Added Work Metrics.

Science.gov (United States)

Kovacs, Mark D; Sheafor, Douglas H; Thacker, Paul G; Hardie, Andrew D; Costello, Philip

2018-03-01

In the era of value-based medicine, it will become increasingly important for radiologists to provide metrics that demonstrate their value beyond clinical productivity. In this article the authors describe their institution's development of an easy-to-use system for tracking value-added but non-relative value unit (RVU)-based activities. Metrix Matrix is an efficient cloud-based system for tracking value-added work. A password-protected home page contains links to web-based forms created using Google Forms, with collected data populating Google Sheets spreadsheets. Value-added work metrics selected for tracking included interdisciplinary conferences, hospital committee meetings, consulting on nonbilled outside studies, and practice-based quality improvement. Over a period of 4 months, value-added work data were collected for all clinical attending faculty members in a university-based radiology department (n = 39). Time required for data entry was analyzed for 2 faculty members over the same time period. Thirty-nine faculty members (equivalent to 36.4 full-time equivalents) reported a total of 1,223.5 hours of value-added work time (VAWT). A formula was used to calculate "value-added RVUs" (vRVUs) from VAWT. VAWT amounted to 5,793.6 vRVUs or 6.0% of total work performed (vRVUs plus work RVUs [wRVUs]). Were vRVUs considered equivalent to wRVUs for staffing purposes, this would require an additional 2.3 full-time equivalents, on the basis of average wRVU calculations. Mean data entry time was 56.1 seconds per day per faculty member. As health care reimbursement evolves with an emphasis on value-based medicine, it is imperative that radiologists demonstrate the value they add to patient care beyond wRVUs. This free and easy-to-use cloud-based system allows the efficient quantification of value-added work activities. Copyright © 2017 American College of Radiology. Published by Elsevier Inc. All rights reserved.

Wood-based composite materials : panel products, glued-laminated timber, structural composite lumber, and wood-nonwood composite materials

Science.gov (United States)

Nicole M. Stark; Zhiyong Cai; Charles Carll

2010-01-01

This chapter gives an overview of the general types and composition of wood-based composite products and the materials and processes used to manufacture them. It describes conventional wood-based composite panels and structural composite materials intended for general construction, interior use, or both. This chapter also describes wood–nonwood composites. Mechanical...

Evaluating Teachers: The Important Role of Value-Added

Science.gov (United States)

Glazerman, Steven; Loeb, Susanna; Goldhaber, Dan; Staiger, Douglas; Raudenbush, Stephen; Whitehurst, Grover

2010-01-01

The evaluation of teachers based on the contribution they make to the learning of their students, "value-added", is an increasingly popular but controversial education reform policy. In this report, the authors highlight and try to clarify four areas of confusion about value-added. The first is between value-added information and the…

Municipal Added Value through Solar Power Systems in the City of Freiburg

Directory of Open Access Journals (Sweden)

Simon Funcke

2012-05-01

Full Text Available The transformation of the conventional energy system towards renewable energies has entailed an increasing decentralization of energy generation in Germany, as the production units are smaller and draw on regional potentials. This can result in positive socio-economic effects in regions where the potential is exploited. The focus of this paper lies on evaluating existing methods and developing new ones, which can be used to determine local added value through renewable energy systems. The methods were required to cover direct as well as induced municipal added value effects and to include all steps of the examined value chain. A combination of methods was tested in a case study for the solar power system value chain in the city of Freiburg (ca. 220,000 inhabitants. The added value through this sector in the year 2009 was calculated at 30.8 million euros through direct effects and 6.2 million euros through induced effects. This total municipal added value of 37 million euros can be converted into roughly 1,500 jobs within the city boundaries. Based on some conservative assumptions, these numbers should be considered as minimum values.

Wood handbook : wood as an engineering material

Science.gov (United States)

Robert J. Ross; Forest Products Laboratory. USDA Forest Service.

2010-01-01

Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

Implementation of Economic Value Added and Market Value Added Analysis as Valuation Tools of Invest Feasibility

Directory of Open Access Journals (Sweden)

Achmad Daengs GS

2017-09-01

Full Text Available For the investors, financial statement is a benchmark of investors in assessing the company's performance. In fact, investors are not always receiving the accurate company's financial statements information and its levels of fairness are in doubt. The financial statement analysis with using financial ratios is not enough. The investors may need to use alternatives financial statement analyses techniques that reflect the actual company's performance. Therefore, both of the investors and the prospective can use Economic Value Added (EVA and Market Value Added (MVA analysis. With these technical analyses, the investors may know the company's performance where they are invested or to be used as a place to invest whether it has value added or not. With the results of these analyses, it is the expected for the investors to be more confident in making decision whether to buy, sell or hold the ownership in the company.

Facilities Management and Value Adding - The LEGO case

DEFF Research Database (Denmark)

Jensen, Per Anker; Katchamart, Akarapong

on the management model for FM included in the European FM standards, recent theories on added value of FM and real estate and the related concept of Value Management from building projects. The paper outlines a preliminary theoretical based management concept, which is investigated, tested and discussed based...... on a case study of LEGO. Results: The study shows that the management model for FM creates a relevant starting point but also that stakeholder and relationship management is an essential aspect of Value Adding Management. The case study confirms the relevance of the basic concept and provides an important...... example of how Value Adding Management can be implemented and added value measured. Practical Implications: The concept of Value Adding Management is expected to increase the awareness of the impacts and strategic importance of FM for organisations and can be a practical tool for facilities managers...

Science supporting the economic and environmental benefits of using wood and wood products in green building construction

Science.gov (United States)

Michael A. Ritter; Kenneth Skog; Richard Bergman

2011-01-01

The objective of this report is to summarize the scientific findings that support the environmental and economic benefits of using wood and wood products in green building construction. Despite documented advantages in many peer-reviewed scientific articles, most building professionals and members of the public do not recognize wood as a renewable resource or the role...

The Value Relevance Of Value Added And Stakeholder Compensation Across Business Cultures

OpenAIRE

John Darcy

2011-01-01

This research performed a partial test of the instrumental validity of the stakeholder model by examining the value relevance of value added relative to income and the incremental value relevance of two stakeholder compensation components of value added, wages and interest for Japan, Germany, United States, and United Kingdom.

Results of the production of wood derived fuels; Puupolttoaineiden tuotantotekniikka - tutkimusalueen katsaus

Energy Technology Data Exchange (ETDEWEB)

Korpilahti, A [Metsaeteho, Helsinki (Finland)

1997-12-31

During the year 1995 there were over 30 projects concerning the production of wood derived fuels going on. Nearly half of them focused on integrated production of pulp wood and wood fuel. About in ten projects work was carried out to promote wood fuel production from logging residues. Other topics were fire wood production, production logistics and wood fuel resources. For production of fuel chips from logging residues, a new chipper truck, MOHA-SISU, was introduced. Having ability to move on terrain, and equipped with drum chipper, hook technic for interchangeable containers and a trailer, the whole production chain can be carried out by the same machine. In Mikkeli region three years of active work promoted the usage of wood fuel in a district power plant to the level of over 110 000 cubic metres of fuel chips. The production costs tend to be a little high in average, and the production chain still needs to be improved. In the field of integrated production a great stride was taken when the first pilot plant using the MASSAHAKE-method started up. Components of the production line and knowledge to operate the process have increased resulting in good performance of the plant. And even another concept for integrated production was introduced. In order to fully control the debarking of small sized trees, a production line of chain flail equipment and debarking drum followed by a chipper and screening facilities was built up. Equipment and machines for harvesting young stands in a way that increases substantially the yield of energy component are still mostly first prototypes. The development of them into well functioning, efficient tools is the most important task in integrated production

Results of the production of wood derived fuels; Puupolttoaineiden tuotantotekniikka - tutkimusalueen katsaus

Energy Technology Data Exchange (ETDEWEB)

Korpilahti, A. [Metsaeteho, Helsinki (Finland)

1996-12-31

During the year 1995 there were over 30 projects concerning the production of wood derived fuels going on. Nearly half of them focused on integrated production of pulp wood and wood fuel. About in ten projects work was carried out to promote wood fuel production from logging residues. Other topics were fire wood production, production logistics and wood fuel resources. For production of fuel chips from logging residues, a new chipper truck, MOHA-SISU, was introduced. Having ability to move on terrain, and equipped with drum chipper, hook technic for interchangeable containers and a trailer, the whole production chain can be carried out by the same machine. In Mikkeli region three years of active work promoted the usage of wood fuel in a district power plant to the level of over 110 000 cubic metres of fuel chips. The production costs tend to be a little high in average, and the production chain still needs to be improved. In the field of integrated production a great stride was taken when the first pilot plant using the MASSAHAKE-method started up. Components of the production line and knowledge to operate the process have increased resulting in good performance of the plant. And even another concept for integrated production was introduced. In order to fully control the debarking of small sized trees, a production line of chain flail equipment and debarking drum followed by a chipper and screening facilities was built up. Equipment and machines for harvesting young stands in a way that increases substantially the yield of energy component are still mostly first prototypes. The development of them into well functioning, efficient tools is the most important task in integrated production

Bioconversion of garden waste, kitchen waste and cow dung into value-added products using earthworm Eisenia fetida

Science.gov (United States)

Wani, K.A.; Mamta; Rao, R.J.

2013-01-01

Solid waste management is a worldwide problem and it is becoming more and more complicated day by day due to rise in population, industrialization and changes in our life style. Transformation of industrial sludges into vermicompost is of double interest: on the one hand, a waste is converted into value added product, and, on the other, it controls a pollutant that is a consequence of increasing industrialization. Garden waste, kitchen waste and cow dung were subjected to recycle through vermicomposting by using the epigeic earthworm Eisenia fetida under field conditions. The pH, moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium in vermicompost was analysed. It was found that moisture content, total organic carbon, humus, nitrogen, phosphorous and potassium was high in cow dung, followed by kitchen waste and garden waste. This study clearly indicates that vermicomposting of garden waste, kitchen waste and cow dung can not only produce a value added produce (vermicomposting) but at the same time reduce the quantity of waste. PMID:23961230

Production of cattle feed by the growth of bacteria on mesquite wood

Energy Technology Data Exchange (ETDEWEB)

Thayer, D W

1975-01-01

The potential for the conversion of mesquite into either a complete animal feed or a protein supplement was evaluated. Species of bacteria which can use the extremely hard mesquite wood as their sole C source were isolated by enrichment culture techniques. Each species was evaluated for its rate of growth, protein production, cellulase activity, amino acid profile of the single-cell protein, and acute toxicity or pathogenicity for weanling mice. The growth products were analyzed for protein, lignin, ash, carbohydrates, and caloric value. The single-cell protein produced from mesquite exceeded or equaled the FAO reference protein in 8 essential amino acids including methionine. No pathogenicity or acute toxicity of the bacteria for weanling mice was found. The results indicate that a high-energy, high-protein, complete cattle feed or an excellent protein supplement can be produced from mesquite wood.

Chapter 6: Wood energy and competing wood product markers

Science.gov (United States)

Kenneth E. Skog; Robert C. Abt; Karen Abt

2014-01-01

Understanding the effect of expanding wood energy markets is important to all wood-dependent industries and to policymakers debating the implementation of public programs to support the expansion of wood energy generation. A key factor in determining the feasibility of wood energy projects (e.g. wood boiler or pellet plant) is the long-term (i.e. 20-30year) supply...

Species selection in secondary wood products: implications for product design and promotion

Science.gov (United States)

Matthew S. Bumgardner; Scott A. Bowe; Scott A. Bowe

2002-01-01

This study investigated the perceptions that people have of several commercially important wood species and determined if word-based and specimen-based evaluations differed. Such knowledge can help secondary wood manufacturers better understand their products and develop more effective design concepts and promotional messages. A sample of more than 250 undergraduate...

THE EFFECT OF LEVERAGE AND ECONOMIC VALUE ADDED ON MARKET VALUE ADDED

Directory of Open Access Journals (Sweden)

Kristína Jančovičová BOGNÁROVÁ

2018-05-01

Full Text Available Economic value added (EVA is a performance measure developed by Stern Stewart & Co. that attempts to measure the true economic profit produced by a company. Such a metric is useful for investors who wish to determine how well a company has produced value for its investors, and it can be compared against the company's peers for a quick analysis of how well the company is operating in its industry. Market value added (MVA, on the other hand, is simply the difference between the current total market value of a company and the capital contributed by investors (including both shareholders and bondholders. It is typically used for companies that are larger and publicly-traded. MVA is not a performance metric like EVA, but instead is a wealth metric, measuring the level of value a company has accumulated over time. In order to maximise the value for shareholders, companies should strive towards maximising MVA and not necessarily their total market value. It is believed, that the best way to do so is to maximize EVA, which reflects a company’s ability to earn returns above the cost of capital. The leverage available to companies that incur fixed costs and use borrowed capital with a fixed interest charge has been known and quantified by financial managers for some time. In this research the effect of leverage and EVA on MVA as the measure of shareholder wealth creation was analysed. Leverage and EVA have been used as the independent variables whereas MVA has been used as the measure of shareholder wealth creation. Correlation and regression methods have been employed to find out in what way financial managers can practice the effects of leverage and EVA to maximize MVA. The results showed that EVA and leverage have no profound impact on MVA of the selected Slovak companies

School system evaluation by value added analysis under endogeneity.

Science.gov (United States)

Manzi, Jorge; San Martín, Ernesto; Van Bellegem, Sébastien

2014-01-01

Value added is a common tool in educational research on effectiveness. It is often modeled as a (prediction of a) random effect in a specific hierarchical linear model. This paper shows that this modeling strategy is not valid when endogeneity is present. Endogeneity stems, for instance, from a correlation between the random effect in the hierarchical model and some of its covariates. This paper shows that this phenomenon is far from exceptional and can even be a generic problem when the covariates contain the prior score attainments, a typical situation in value added modeling. Starting from a general, model-free definition of value added, the paper derives an explicit expression of the value added in an endogeneous hierarchical linear Gaussian model. Inference on value added is proposed using an instrumental variable approach. The impact of endogeneity on the value added and the estimated value added is calculated accurately. This is also illustrated on a large data set of individual scores of about 200,000 students in Chile.

Value management program: performance, quantification, and presentation of imaging value-added actions.

Science.gov (United States)

Patel, Samir

2015-03-01

Health care is in a state of transition, shifting from volume-based success to value-based success. Hospital executives and referring physicians often do not understand the total value a radiology group provides. A template for easy, cost-effective implementation in clinical practice for most radiology groups to demonstrate the value they provide to their clients (patients, physicians, health care executives) has not been well described. A value management program was developed to document all of the value-added activities performed by on-site radiologists, quantify them in terms of time spent on each activity (investment), and present the benefits to internal and external stakeholders (outcomes). The radiology value-added matrix is the platform from which value-added activities are categorized and synthesized into a template for defining investments and outcomes. The value management program was first implemented systemwide in 2013. Across all serviced locations, 9,931.75 hours were invested. An annual executive summary report template demonstrating outcomes is given to clients. The mean and median individual value-added hours per radiologist were 134.52 and 113.33, respectively. If this program were extrapolated to the entire field of radiology, approximately 30,000 radiologists, this would have resulted in 10,641,161 uncompensated value-added hours documented in 2013, with an estimated economic value of $2.21 billion. Copyright © 2015 American College of Radiology. Published by Elsevier Inc. All rights reserved.

MODELS OF APPLICATION ECONOMIC VALUE ADDED IN AUTOMOTIVE COMPANY

Directory of Open Access Journals (Sweden)

Eva MALICHOVA

2017-09-01

Full Text Available Enterprises are currently trying to bring new technologies into production and use new procedures and recommendations in various management activities. However, they should not forget to change their approach to the evaluation of the results achieved and focus on the use of modern methods of performance evaluation and prove to apply them in their enterprises. The aim of this paper is to point out several variants of the calculation of Economic value added (EVA indicator, define the possibilities to apply EVA methods to the conditions of enterprises in the Slovak Republic and the need to adjust data providing financial statements and data for current accounts. Application of economic value added should be able to contribute to changes in the views of the owners and managers of enterprises in the Slovak republic for use not only as financial indicators.

Simultaneous production of bioethanol and value-added d-psicose from Jerusalem artichoke (Helianthus tuberosus L.) tubers.

Science.gov (United States)

Song, Younho; Oh, Chihoon; Bae, Hyeun-Jong

2017-11-01

In this study, the production of bioethanol and value added d-psicose from Jerusalem artichoke (JA) was attempted by an enzymatic method. An enzyme mixture used for hydrolysis of 100mgmL -1 JA. The resulting concentrations of released d-fructose and d-glucose were measured at approximately 56mgmL -1 and 15mgmL -1 , respectively. The d-psicose was epimerized from the JA hydrolyzate, and the conversion rate was calculated to be 32.1%. The residual fructose was further converted into ethanol at 18.0gL -1 and the yield was approximately 72%. Bioethanol and d-psicose were separated by pervaporation. This is the first study to report simultaneous d-psicose production and bioethanol fermentation from JA. Copyright © 2017 Elsevier Ltd. All rights reserved.

Waste wood incineration: long-lasting, environment-friendly and CO2-neutral

International Nuclear Information System (INIS)

Bouma, J.W.J.

1993-01-01

The economic aspects of energy production from waste wood are evaluated. Heating systems based on the incineration of wood have been considerably improved recently. Several aspects of the incineration of waste wood are reviewed: the implications with regard to the greenhouse effect, the calorific value of wood, the incineration process, and the cost price calculation of energy production by waste wood incineration. In conclusion is stated that energy production by waste wood incineration is a valuable economic alternative for heat production by oil products, especially in view of the current anti-pollution taxes in Belgium. (A.S.)

Wood product industry - present state and studies of the development alternatives; Puuteollisuuden nykytilan ja haasteiden arviointia

Energy Technology Data Exchange (ETDEWEB)

Holmijoki, O.; Paajanen, T.; Kairi, M.

2007-07-01

In this research project the development of the wood products industry and its operating environment in Finland was studied using statistical data mainly from years 1995 - 2003. In this context, the wood products industry includes the sawmilling industry, the plywood and other wood panel industry, prefabricated wooden housing and the building joinery industry, wood packing manufacture and the manufacture of other wooden products. The development of the wood products industry and its operating environment has been estimated by combining statistical data about the business economy, production economy and the national economy from the Central Statistical Office of Finland together with data from the Finnish Forest Research Institute. Based on statistical data, the wood product markets, profitability and cost structure of branches, input market, use of labour force and investments have been studied. The economic importance of the wood products industry has been estimated at a national and a local level. Challenges facing wood products industry branches have been analysed using example calculations based on input-output theory. In the evaluation method, the business environment of the wood products industry branches and related branches, have been described with a use table at basic prices commonly using in the national economy. This method has enabled the direct and indirect effects of simultaneous quantity and price changes occurring in the wood product markets and markets related to the wood product industry, to be analysed. In the example calculations, variation of sawn timber production and log import, as well as the increments of sawn timber upgrading, wood product usage in building, wood panel production and purchase energy price, were reviewed

Value Added Elements According to Buyer Companies in a B2B Context

Directory of Open Access Journals (Sweden)

Daniel Battaglia

2015-07-01

Full Text Available This paper analyses how buyer companies perceive the value added to products and services offered by their suppliers and identifies the predominant elements that affect purchasing decisions and establishment of relationships between companies in a B2B context. A multiple case study was developed in 12 buyer companies from three industrial segments in southern Brazil: metal-mechanics, furniture and foods. The findings show that for supplier companies in the metal-mechanics industry to add value, they must identify buyers’ needs, develop technology/innovation, be focused on competitive aspects, keep control of the supply chain, provide different purchasing channels, develop partnerships, and adapt to cultural aspects. Companies in the food industry consider the model for creating value to adapt to meet customer needs, the effective use of purchasing channels, functionality of products, and technical knowledge. The companies in the furniture industry value the methods that suppliers use to capture and implement required changes, effective control of the supply chain, and the representativeness of the suppliers’ brand in the market. This study captures the perception of buyer companies in relation to predominant value-adding elements and could guide decisions for the adoption of managerial actions by supplier companies focused on adding value.

Comparing energy use and environmental emissions of reinforced wood doors and steel doors

Science.gov (United States)

Lynn Knight; Melissa Huff; Janet I. Stockhausen; Robert J. Ross

2005-01-01

The USDA Forest Service Forest Products Laboratory has patented a technology that incorporates fiberglass-reinforced wood into the structure of wood doors and other wood building products. The process of reinforcing wood doors with epoxy and fiberglass increases the strength and durability of the product. Also, it allows the use of low-value, small-diameter wood which...

Wood pellets : a worldwide fuel commodity

International Nuclear Information System (INIS)

Melin, S.

2005-01-01

Aspects of the wood pellet industry were discussed in this PowerPoint presentation. Details of wood pellets specifications were presented, and the wood pellet manufacturing process was outlined. An overview of research and development activities for wood pellets was presented, and issues concerning quality control were discussed. A chart of the effective calorific value of various fuels was provided. Data for wood pellet mill production in Canada, the United States and the European Union were provided, and various markets for Canadian wood pellets were evaluated. Residential sales as well as Canadian overseas exports were reviewed. Production revenues for British Columbia and Alberta were provided. Wood pellet heat and electricity production were discussed with reference to prefabricated boilers, stoves and fireplaces. Consumption rates, greenhouse gas (GHG) emissions, and fuel ratios for wood pellets and fossil fuels were compared. Price regulating policies for electricity and fossil fuels have prevented the domestic expansion of the wood pellet industry. There are currently no incentives for advanced biomass combustion to enter British Columbia markets, and this has led to the export of wood pellets. It was concluded that climate change mitigation policies will be a driving force behind market expansion for wood pellets. tabs., figs

Impact of European Union Timber Regulation on Forest Certification Strategies in the Finnish Wood Industry Value Chain

Directory of Open Access Journals (Sweden)

Jani Holopainen

2015-08-01

Full Text Available The aim of this explorative study is to find out how the EU Timber Regulation (EUTR has affected the forest and chain of custody (CoC certification strategies and practices among the Finnish wood industry companies. We are especially interested to find out whether more integrated strategies and collaborative networks have emerged for enhanced communications throughout the industry value chains. This qualitative interview study included both EUTR ex ante and ex post analysis, based on three rounds of managerial and expert interviews during 2011–2015. The results indicate that the EUTR appears to have enforced the supplier–client relations in the Finnish wood industry value chain. The sector still lacks integrated communication strategies with better understanding of customer and stakeholder values, which could contribute to more cohesive communication and marketing efforts reflecting the values of the whole industry. The certification practices are fairly spontaneously implemented following the traditional industry culture, which is not supportive of innovations and gaining competitive advantages in the broader material markets. Furthermore, the existence of two parallel forest certificates (Forest Stewardship Council (FSC and Programme for the Endorsement of Forest Certification (PEFC seems to hamper the effective communication and building of an image of sustainable wood products among customers and end consumers, groups that are also exposed to more general environmental communication, e.g., in the building material markets.

Utilization potential of wood clones of Eucalyptus urophylla in the production of wood-cement panels

Directory of Open Access Journals (Sweden)

Lourival Marin Mendes

2011-03-01

Full Text Available The objective of this study was to evaluate the potential of using clones of Eucalyptus urophylla in the production of wood-cement panels. The study used six clones of Eucalyptus urophylla with 8 years of age, from the Companhia Mineira de Metais, located in Paracatu - MG. For the formation of the panels it was used Portland cement CP V - ARI / Plus, possessing high initial resistance to mineral binder and calcium chloride (CaCl2 as accelerator for the cement curing. The panels were produced with the following parameters: dimensions of 49.5 x 49.5 x 1.5 cm, nominal density of 1.2 g/cm ³, relation wood: cement (1:2.5 and relation water: cement (1:1.5. The results can showed that: (1 for thickness swelling in two and twenty-four hours, only clones 19.28 and 58 attended the specifications, (2 for water absorption, clone 62 showed the best results, (3 to internal bond, only clone 58 didn`t attend specifications, (4 for the compression, clones 19.36 and 58 showed the best results, (5 for MOE and MOR, none of the clones presented values compatible to the bison process. It is suggested the continuation of this line of research, including the manipulation of variables of production, so that all properties be compatible to the minimum required standards.

Leading Change, Adding Value.

Science.gov (United States)

Evans, Nick

2016-09-12

Essential facts Leading Change, Adding Value is NHS England's new nursing and midwifery framework. It is designed to build on Compassion in Practice (CiP), which was published 3 years ago and set out the 6Cs: compassion, care, commitment, courage, competence and communication. CiP established the values at the heart of nursing and midwifery, while the new framework sets out how staff can help transform the health and care sectors to meet the aims of the NHS England's Five Year Forward View.

The suitability of selected wood species in the production of turned ...

African Journals Online (AJOL)

The study investigated the suitability of selected wood species in the production of turned glue-laminated products. Five different wood species of high quality grades which were sourced from Bodija market Ibadan, south western Nigeria were thoroughly examined where the moisture content, density and shrinkage ...

Granulated wood ash to forest soil - Ecological effects

International Nuclear Information System (INIS)

Rosen, K.; Eriksson, H.; Clarholm, M.; Lundkvist, H.; Rudebeck, A.

1993-01-01

This report describes research concerning ecological effects of wood ash recycling to forest soils. The main part of the minerals in the wood fuels are retained in the ashes after combustion. By returning the ashes back to the cleared forest areas, the mineral losses can be reduced. Adding ashes and limestone is a method to vitalize acidified forest soils and restore the production capacity. 48 refs, 26 figs, 8 tabs

NIR Techniques Create Added Values for the Pellet and Biofuel Industry

Energy Technology Data Exchange (ETDEWEB)

Lestander, Torbjoern A. [Swedish Univ of Agricultural Science, Umeaa (Sweden). Unit of Biomass Technology and Chemistry; Johnsson, Bo; Grothage, Morgan [Casco Adhesives AB, Sundsvall (Sweden)

2006-07-15

biofuels for heating. The factors varied were: high and low values of drying temperature and of wood powder dryness, and binary mixes of sawdust from the conifers Norway spruce and Scots pine. The mixes of raw sawdust was dried and milled into powder before pelletizing. In all 11 runs including three center points were conducted. Each run gave about 10 Mg of wood Pellets. The validation of a running multivariate calibration model for on-line NIR spectra in the pellet plant showed high accuracy with a prediction error of 0.42 % water content in the milled sawdust dried to c. 7-11 % water content. Also the NIR based models for drying temperature and binary mixes of sawdust from the two species gave good predictions. Validation of the model for drying temperature of saw dust resulted in lower prediction accuracy for prolonged periods. The findings indicate that also chemical contents, for example contents of extractives, such as fatty and resin acids, in dried and milled sawdust, can be predicted by on-line NIR technique as these contents are highly correlated with the used tree species and pretreatments of the sawdust. Multivariate statistical methods, besides resulting in calibrations, are also useful in model interpretation of the wide and overlapping peaks in the NIR wavelength region. The possibilities to meet costumer specifications and create added values are enhanced by the NIR technique that, further, can be used as an important tool in the monitoring and control of the pelletizing process as well as in characterization and standardization of biofuels on the world market. The NIR technique can also be implemented in process analytical technology that has the ultimate goal to understand and control the manufacturing process to ensure the quality of the final product to the consumer. (Full text of contribution)

Recycling of wood products. Final report of the preliminary study project partly financed by the Finnish Wood Research Oy; Puutuotteiden kierraetys. Finnish Wood Research Oy:n osarahoittaman esiselvityshankkeen loppuraportti

Energy Technology Data Exchange (ETDEWEB)

Pirhonen, I.; Heraejaervi, H.; Saukkola, P.; Raety, T.; Verkasalo, E., Email: henrik.herajarvi@metla.fi

2011-07-01

The objective of this preliminary study was to clarify the present state of recycling of wood in Finland and Europe. In the work the control measures of recycling were examined. In Finland there will be a total amount of 850 000 tons of waste wood per year. Of this amount 670 000 tons is from construction and demolishing of buildings. Burning the wood to energy is technically and economically the most reasonable use of waste wood in Finland and in several other European countries where there is a long heating season. A lot of work has been done to find new ways of utilization. The objective of the European Union to increase the use of renewable natural resources in the energy production creates an additional demand to all kinds of wood, including waste wood. The waste legislation of Finland and EU is directing to recycling, not restricting it. Furthermore, the systems to try to create markets for products containing recycled materials are under development. In the future it is expected that the legislation is tightening and the burning of waste wood is no longer calculated as acceptable recycling. Other ways to utilize wood waste should then already be developed. Furthermore, the development and introduction of new recycling methods are of important significance also when marketing wood and wood products. The recycling should be taken into consideration already at the planning stage of the building

Overall ecologic evaluation of cascading use of wood. Environmental impacts of substantial and energetic systems for utilization of wood in comparison; Gesamtoekologische Bewertung der Kaskadennutzung von Holz. Umweltauswirkungen stofflicher und energetischer Holznutzungssysteme im Vergleich

Energy Technology Data Exchange (ETDEWEB)

Gaertner, Sven; Hienz, Gunnar; Keller, Heiko; Mueller-Lindenlauf, Maria

2013-01-15

Wood demand is rising and its production can only be extended to a certain degree. This requires a prioritisation of wood use options. Therefore, the environmental aspects of using wood for energy production or as a material with and without cascading recycling steps of stepwise lower value are studied in a comprehensive life cycle assessment (LCA). In addition, the environmental impacts of tapping new wood resources are assessed qualitatively. The results show that under most conditions the environmental impacts are the lower the more steps of a high-value material use are performed before the wood is used for energy production. One has to consider, though, that extended material use cascades can cause decades of delays of the energy recovery step, which may lead to the replacement of cleaner energy sources in the future and thus impair the results for the long-lived wood products. At the same time, wood products can represent a temporary or even - if material wood use generally increases - a long-term carbon stock. This leads to a delay of the greenhouse effect. Depending on the assessment method, these opposing effects result in unchanged to diminished impacts of long-lived wood products on the climate. Nevertheless, from an environmental point of view, high-value material use is advantageous compared to a direct use of wood for energy production independent of the assessment method. When comparing material use options of wood, especially the high-quality use of high-value wood assortments (e.g. solid wood as construction wood) is associated with positive results from an environmental perspective. In this context, the main effects on the LCA results come from the choice of the non-wood reference product and its associated environmental impacts. Regarding the direct use of wood for energy production, the most advantageous option from an environmental point of view is a combined heat and power plant (CHP) with a high overall efficiency.

Does Distance to Subsidiaries affect Headquarters Value Added?

DEFF Research Database (Denmark)

Nell, Phillip C.; Beugelsdijk, Sjoerd; Ambos, Björn

2014-01-01

How does distance between MNC headquarters and their subsidiaries affect the value added generated by headquarters? Integrating theories on spatial transaction costs with the headquarter view of the MNC, we link two types of distances, geographic distance and contextual distance, with headquarters...... value added. We test our hypotheses on an original dataset of 124 manufacturing subsidiaries in Europe. We find that the relation between distance and headquarters value added is conditional on the degree of subsidiaries’ external embeddedness. We find no direct effect of distance. The value added...... of headquarters is highest for subsidiaries that are not externally embedded in the host country and that operate at a large distance. It is lowest for locally responsive subsidiaries with high external embeddedness operating at a large distance. We discuss implications for the literature on headquarters-subsidiaries...

A step-by-step plan to manage and measure adding value by FM/CREM

DEFF Research Database (Denmark)

van der Voordt, Theo; Jensen, Per Anker; Hoendervanger, Jan Gerard

2016-01-01

Purpose To present a new Value Adding Management model in order to support decision makers in identifying appropriate interventions to add value to the organisation, to manage its implementation, and to measure the output and outcomes. Theory The paper builds on value adding management theories...... different European countries present a state of the art of theory and research on 12 value parameters, how to manage and measure each value, and to discuss the costs and benefits of typical FM and CREM interventions to enhance satisfaction, image, culture, health and safety, productivity, adaptability...... and models including the triplet input-throughput-output, a distinction between output, outcome and added value, the Plan-Do-Act-Check cycle, change management and performance measurement. Design/methodology/approach Literature review and a cross-chapter analysis of a forthcoming book, where authors from...

Adding Value by Hospital Real Estate: An Exploration of Dutch Practice.

Science.gov (United States)

van der Zwart, Johan; van der Voordt, Theo J M

2016-01-01

To explore how hospital real estate can add value to the healthcare organization, which values are prioritized in practice, and why. Dutch healthcare organizations are self-responsible for the costs and benefits of their accommodation. Meanwhile, a lively debate is going on about possible added values of corporate and public real estate in the fields of corporate real estate management and facility management. This article connects both worlds and compares insights from literature with experiences from practice. Added values extracted from literature have been discussed with 15 chief executive officers and project leaders of recently newly built hospitals in the Netherlands. Interviewees were asked (1) which values are included in the design and management of their hospital and why, (2) to prioritize most important values from a list of nine predefined values, and (3) to explain how the chosen real estate decisions are supposed to support organizational objectives. Stimulating innovation, user satisfaction, and improving organizational culture are most highly valued, followed by improving productivity, reducing building costs, and creating building flexibility. Image, risk control, and financing possibilities got lower rankings. The findings have been used to develop a value-impact matrix that connects nine values to various stakeholders and possible interventions. The findings and the value-impact matrix can make different stakeholders aware of many possible added values of hospital real estate, potential synergy and conflicts between different values, and how to steer on value add in different phases of the life cycle. © The Author(s) 2015.

Wood Degradation by Thermotolerant and Thermophilic Fungi for Sustainable Heat Production

NARCIS (Netherlands)

Caizan Juanarena, Leire; ter Heijne, Annemiek; Buisman, Cees; Van der Wal, A.

2016-01-01

The use of renewable biomass for production of heat and electricity plays an important role in the circular economy. Degradation of wood biomass to produce heat is a clean and novel process proposed as an alternative to wood burning, and could be used for various heating applications. So far, wood

World trade in forest products and wood fuel

International Nuclear Information System (INIS)

Hillring, Bengt

2006-01-01

Wood fuel is a strategic resource for future energy supply and is usually utilised locally. Traditional use of wood fuel and other bioenergy has a share of 10-15% energy supply, used mainly for the household sector. The utilisation for industrial purposes is much smaller but is a strategic resource in the effort to fulfil the Kyoto agreement to replace fossil fuels and to mitigate greenhouse gas emissions. Many industrialised countries already use a significant share of biofuels in their energy supply e.g. Nordic countries while others like some other European Union countries are planning to increase their use. Production and use of biofuels need to be carried out sustainable. Official statistics do not report trade in such detail that international trade in different biomass types can be fully identified. However, FAO and European Forestry Institute are important sources. In some countries, there is a growing interest in the international trade, because the trade can provide biofuels at lower prices, larger quantities and better quality than domestic alternatives. The first signs of an international market price for wood fuel are indicated in Europe. For the future both the use and the trade of wood fuel is expected to increase. Analyses for trade in charcoal, wood chips, fuel wood and wood residues made in this report identify 'hot' trade spots in Europe, in south East Asia and in North America

IMPROVEMENT OF KEY PROCESSES THROUGH THE ANALYSIS OF VALUE ADDED IN TECHNOLOGY- BASED COMPANIES A SINGLE PROJECT PRODUCTIONS OF THE WATER SECTOR IN CUBA

Directory of Open Access Journals (Sweden)

Reina Maylín, Hernández Oro

2012-01-01

Full Text Available In this paper, we present the main results of research designed to improve key business processes, using a procedure designed for this purpose, and which includes among its main stages, the analysis of value added by activity, adapting to technology based companies’ productions by one of the water sector project in Cuba. The procedure consistently combines different techniques such as multi-criteria decision analysis for selection of the key processes and analysis of value added by activity to identify key processes to improve and identify opportunities for improvement. The main results are able to identify, classify and relate the processes taking place in the organization, and represent them in a process map, and then determine the key processes for improvement, based on the analysis of value added at each process of each of the activities in it. Derived from the results obtained are proposed and implemented a set of organizational improvements had a positive economic impact for the company under study, allowing a positive conclusion on the feasibility of implementation, flexibility and robustness of the procedure developed in technology-based companies single project productions of the water sector in Cuba to support their business management.

Nondestructive chemical imaging of wood at the micro-scale: advanced technology to complement macro-scale evaluations

Science.gov (United States)

Barbara L. Illman; Julia Sedlmair; Miriam Unger; Carol Hirschmugl

2013-01-01

Chemical images help understanding of wood properties, durability, and cell wall deconstruction for conversion of lignocellulose to biofuels, nanocellulose and other value added chemicals in forest biorefineries. We describe here a new method for nondestructive chemical imaging of wood and wood-based materials at the micro-scale to complement macro-scale methods based...

Lignin depolymerization and upgrading via fast pyrolysis and electrocatalysis for the production of liquid fuels and value-added products

Science.gov (United States)

Garedew, Mahlet

The production of liquid hydrocarbon fuels from biomass is needed to replace fossil fuels, which are decreasing in supply at an unsustainable rate. Renewable fuels also address the rising levels of greenhouse gases, an issue for which the Intergovernmental Panel on Climate Change implicated humanity in 2013. In response, the Energy Independence and Security Act (EISA) mandates the production of 21 billion gallons of advanced biofuels by 2022. Biomass fast pyrolysis (BFP) uses heat (400-600 °C) without oxygen to convert biomass to liquids fuel precursors offering an alternative to fossil fuels and a means to meet the EISA mandate. The major product, bio-oil, can be further upgraded to liquid hydrocarbon fuels, while biochar can serve as a solid fuel or soil amendment. The combustible gas co-product is typically burned for process heat. Though the most valuable of the pyrolysis products, the liquid bio-oil is highly oxygenated, corrosive, low in energy content and unstable during storage. As a means of improving bio-oil properties, electrocatalytic hydrogenation (ECH) is employed to reduce and deoxygenate reactive compounds. This work specifically focuses on lignin as a feed material for BFP. As lignin comprises up to 30% of the mass and 40% of the energy stored in biomass, it offers great potential for the production of liquid fuels and value-added products by utilizing fast pyrolysis as a conversion method coupled with electrocatalysis as an upgrading method.

A multi-tiered approach for assessing the forestry and wood products industries' impact on the carbon balance.

Science.gov (United States)

Knauf, Marcus

2015-12-01

The forestry and wood products industries play a significant role in CO 2 emissions reduction by increasing carbon stocks in living forest biomass and wood products. Moreover, wood can substitute for fossil fuels. Different methods can be used to assess the impact of regional forestry and wood products industries on regional CO 2 emissions. This article considers three of those methods and combines them into a multi-tiered approach. The multi-tiered approach proposed in this article combines: 1) a Kyoto-Protocol-oriented method focused on changes in CO 2 emissions resulting from regional industrial production, 2) a consumer-oriented method focused on changes in CO 2 emissions resulting from regional consumption, and 3) a value-creation-oriented method focused on changes in CO 2 emissions resulting from forest management and wood usage strategies. North Rhine-Westphalia is both a typical German state and an example of a region where each of these three methods yields different results. It serves as a test case with which to illustrate the advantages of the proposed approach. This case study argues that the choice of assessment methods is essential when developing and evaluating a strategy for reducing CO 2 emissions. Emissions can be reduced through various social and economic processes. Since none of the assessment methods considered above is suitable for all of these processes, only a multi-tiered approach may ensure that strategy development results in an optimal emissions reduction strategy.

LCA-based optimization of wood utilization under special consideration of a cascading use of wood.

Science.gov (United States)

Höglmeier, Karin; Steubing, Bernhard; Weber-Blaschke, Gabriele; Richter, Klaus

2015-04-01

Cascading, the use of the same unit of a resource in multiple successional applications, is considered as a viable means to improve the efficiency of resource utilization and to decrease environmental impacts. Wood, as a regrowing but nevertheless limited and increasingly in demand resource, can be used in cascades, thereby increasing the potential efficiency per unit of wood. This study aims to assess the influence of cascading wood utilization on optimizing the overall environmental impact of wood utilization. By combining a material flow model of existing wood applications - both for materials provision and energy production - with an algebraic optimization tool, the effects of the use of wood in cascades can be modelled and quantified based on life cycle impact assessment results for all production processes. To identify the most efficient wood allocation, the effects of a potential substitution of non-wood products were taken into account in a part of the model runs. The considered environmental indicators were global warming potential, particulate matter formation, land occupation and an aggregated single score indicator. We found that optimizing either the overall global warming potential or the value of the single score indicator of the system leads to a simultaneous relative decrease of all other considered environmental impacts. The relative differences between the impacts of the model run with and without the possibility of a cascading use of wood were 7% for global warming potential and the single score indicator, despite cascading only influencing a small part of the overall system, namely wood panel production. Cascading led to savings of up to 14% of the annual primary wood supply of the study area. We conclude that cascading can improve the overall performance of a wood utilization system. Copyright © 2015 Elsevier Ltd. All rights reserved.

Adding Production Value Through Application of Value Based Scheduling

DEFF Research Database (Denmark)

Lindhard, Søren; Wandahl, Søren

2012-01-01

Customer value is a key goal in the Lean philosophy, essentially only actions that adds value should be conducted. In a transformation view, the basic lean approach is to remove waste, which indirectly increases value (or withstand value lose). Lean Construction acknowledges two different types o...... be minimized and management should seek towards democratic leadership....

The Role of Value Added Tax on Economic Growth of Ethiopia ...

African Journals Online (AJOL)

The achievement of economic growth is crucial for countries sustainable development. Recently, Value Added Tax (VAT) becomes a major worldwide tax instrument which enhances economic growth. Being a tax levied on the final consumption of goods and services, VAT is collected at each stage of production and ...

Bioenergy Research Programme, Yearbook 1995. Production of wood fuels; Bioenergian tutkimusohjelma, vuosikirja 1995. Puupolttoaineen tuotantotekniikka

Energy Technology Data Exchange (ETDEWEB)

Alakangas, E [ed.

1997-12-31

Bioenergy Research Programme is one of the energy technology research programmes of the Technology Development Center TEKES. The aim of the Bioenergy Research Programme is to increase, by using technical research and development, the economically profitable and environmentally sound utilisation of bioenergy, to improve the competitiveness of present peat and wood fuels, and to develop new competitive fuels and equipment related to bioenergy. The funding for 1995 was nearly 52 million FIM and the number of projects 66. The main goal of the wood fuels research area is to develop new production methods in order to decrease the production costs to the level of imported fuels. The total potential of the wood fuel use should be at least 1.0 million toe/a (5.5 million m{sup 3}). During the year 1995 There were over 30 projects concerning the production of wood derived fuels going on. Nearly half of them focused on integrated production of pulp wood and wood fuel. About ten projects was carried out to promote the wood fuel production from logging residues. Other topics were firewood production, production logistics and wood fuel resources. For production of fuel chips from logging residues, a new chipper truck, MOHA-SISU, was introduced. The new machine gives a new logistic solution resulting in high productivity and reasonable operating costs. In Mikkeli region three years of active work promoted the usage of wood fuel in a district power plant to the level of over 110 000 m{sup 3} of fuel chips. The production costs tend to be a little high in average, and the production chain still needs to be improved

Bioenergy Research Programme, Yearbook 1995. Production of wood fuels; Bioenergian tutkimusohjelma, vuosikirja 1995. Puupolttoaineen tuotantotekniikka

Energy Technology Data Exchange (ETDEWEB)

Alakangas, E. [ed.

1996-12-31

Bioenergy Research Programme is one of the energy technology research programmes of the Technology Development Center TEKES. The aim of the Bioenergy Research Programme is to increase, by using technical research and development, the economically profitable and environmentally sound utilisation of bioenergy, to improve the competitiveness of present peat and wood fuels, and to develop new competitive fuels and equipment related to bioenergy. The funding for 1995 was nearly 52 million FIM and the number of projects 66. The main goal of the wood fuels research area is to develop new production methods in order to decrease the production costs to the level of imported fuels. The total potential of the wood fuel use should be at least 1.0 million toe/a (5.5 million m{sup 3}). During the year 1995 There were over 30 projects concerning the production of wood derived fuels going on. Nearly half of them focused on integrated production of pulp wood and wood fuel. About ten projects was carried out to promote the wood fuel production from logging residues. Other topics were firewood production, production logistics and wood fuel resources. For production of fuel chips from logging residues, a new chipper truck, MOHA-SISU, was introduced. The new machine gives a new logistic solution resulting in high productivity and reasonable operating costs. In Mikkeli region three years of active work promoted the usage of wood fuel in a district power plant to the level of over 110 000 m{sup 3} of fuel chips. The production costs tend to be a little high in average, and the production chain still needs to be improved

PENGARUH SERVICE QUALITY, PRODUCT QUALITY DAN PERCEIVED VALUE TERHADAP KEPUASAN DAN LOYALITAS PELANGGAN INDUSTRI KAYU PERHUTANI

Directory of Open Access Journals (Sweden)

Winarni Saftarya Timedina Gultom

2016-07-01

Full Text Available The purpose of this research is to analyze the influences of service quality, product quality and perceived value on the satisfaction and loyalty of the customers of Perhutani wood industry, the level of customer satisfaction and loyalty and managerial implications. Four data analysis techniques were used including the structural equation modeling partial least squares (SEMPLS with 24 exogenous latent variable attributes and 6 endogenous latent variable attributes; CSI, CLI and IPA. SEMPLS results showed that the variables of service quality (T-statistic=2, 79*>T-table=1, 96 and product quality (T-statistic=6, 45*>T-table=1, 96 significantly influence the satisfaction of the customers of Perhutani wood industry. Perceived value variable (T-statistic=0, 65product quality, and perceived value provided by Perhutani wood industry. The main priority of the performances to be improved based on IPA include the attributes of accuracy of product sizes: length, width, thickness, complaint handling, product delivery, service employees, comprehension of needs, officer awareness, information on the documents and prevailing prices, service time completion, purchase document accuracy, price certainty, allocation certainty, suitability prices with quality, and affordable product prices.Keywords: perhutani, wood industry, satisfaction, loyalty, SEMPLS

Still rethinking the value of high wood density.

Science.gov (United States)

Larjavaara, Markku; Muller-Landau, Helene C

2012-01-01

In a previous paper, we questioned the traditional interpretation of the advantages and disadvantages of high wood density (Functional Ecology 24: 701-705). Niklas and Spatz (American Journal of Botany 97: 1587-1594) challenged the biomechanical relevance of studying properties of dry wood, including dry wood density, and stated that we erred in our claims regarding scaling. We first present the full derivation of our previous claims regarding scaling. We then examine how the fresh modulus of rupture and the elastic modulus scale with dry wood density and compare these scaling relationships with those for dry mechanical properties, using almost exactly the same data set analyzed by Niklas and Spatz. The derivation shows that given our assumptions that the modulus of rupture and elastic modulus are both proportional to wood density, the resistance to bending is inversely proportional to wood density and strength is inversely proportional with the square root of wood density, exactly as we previously claimed. The analyses show that the elastic modulus of fresh wood scales proportionally with wood density (exponent 1.05, 95% CI 0.90-1.11) but that the modulus of rupture of fresh wood does not, scaling instead with the 1.25 power of wood density (CI 1.18-1.31). The deviation from proportional scaling for modulus of rupture is so small that our central conclusion remains correct: for a given construction cost, trees with lower wood density have higher strength and higher resistance to bending.

Estimating Preferences for Wood Products with Environmental Attributes

Directory of Open Access Journals (Sweden)

Masaji Sakagami

2018-01-01

Full Text Available Tropical deforestation and forest degradation are serious problems for the global environment; as a result, sustainable forest management and forest certification have become important. In this study, using a choice experiment, we investigated, on the demand side, consumers’ preferences and willingness to pay (WTP for certified wood products that attempt to address public concerns regarding deforestation and forest degradation. Specifically, we investigated how estimates of consumers’ preferences and WTP were influenced by product attributes such as quality, certification, and price. To the authors’ knowledge, few studies of this kind have been conducted, particularly in Japan. The study’s main finding was that Japanese consumers were willing to pay a premium for certified wood products with attributes related to sustainable forest management; most preferred were products with attributes related to preserving biodiversity. These findings indicate that consumers are willing to pay a premium for products that contribute to solving the problems of deforestation and forest degradation.

A Method for Proposing Valued-Adding Attributes in Customized Housing

Directory of Open Access Journals (Sweden)

Cynthia S. Hentschke

2014-12-01

Full Text Available In most emerging economies, there has been many incentives and high availability of funding for low-cost housing projects. This has encouraged product standardization and the application of mass production ideas, based on the assumption that this is the most effective strategy for reducing costs. However, the delivery of highly standardized housing units to customers with different needs, without considering their lifestyle and perception of value, often results in inadequate products. Mass customization has been pointed out as an effective strategy to improve value generation in low-cost housing projects, and to avoid waste caused by renovations done in dwellings soon after occupancy. However, one of the main challenges for the implementation of mass customization is the definition of a set of relevant options based on users’ perceived value. The aim of this paper is to propose a method for defining value adding attributes in customized housing projects, which can support decision-making in product development. The means-end chain theory was used as theoretical framework to connect product attributes and costumers’ values, through the application of the laddering technique. The method was tested in two house-building projects delivered by a company from Brazil. The main contribution of this method is to indicate the customization units that are most important for users along with the explanation of why those units are the most relevant ones.

Future carbon storage in harvested wood products from Ontario's Crown forests

Science.gov (United States)

Jiaxin Chen; Stephen J. Colombo; Michael T. Ter-Mikaelian; Linda S. Heath

2008-01-01

This analysis quantifies projected carbon (C) storage in harvested wood products (HWP) from Ontario's Crown forests. The large-scale forest C budget model, FORCARB-ON, was applied to estimate HWP C stock changes using the production approach defined by the Intergovernmental Panel on Climate Change. Harvested wood volume was converted to C mass and allocated to...

Assessing potential sustainable wood yield

Science.gov (United States)

Robert F. Powers

2001-01-01

Society is making unprecedented demands on world forests to produce and sustain many values. Chief among them is wood supply, and concerns are rising globally about the ability of forests to meet increasing needs. Assessing this is not easy. It requires a basic understanding of the principles governing forest productivity: how wood yield varies with tree and stand...

Value added planning: yes, in my backyard! : understanding value added planning in the city of Amersfoort, the Netherlands

NARCIS (Netherlands)

Diemont, E.; Cilliers, J.; Stobbelaar, D.J.; Timmermans, W.

2011-01-01

Amersfoort local municipality would like to renew the quality of the green spaces within the urban areas, to enhance the value of these spaces and to determine the economic value of green spaces. The concept of Value Added Planning was introduced to address these objectives. The value of green is

Utilization of tuna roe and using inulin as oil replacer for producing value added omega-3 mayonnaise product

Directory of Open Access Journals (Sweden)

Kanrawee Hunsakul

2016-03-01

Full Text Available Background: The fishery industry has been important for Thailand’s economy for more than 30 years. For example, Thailand isthe world’s largest canned tuna producer and exporter. However, onlyordinary meat or white meatis usedfor raw materialin canned tuna products. Whileroe, viscera, head and dark meataresold at cheap prices,with theseby-products being usedto feed plant or local human food,its nutritive values withfat,protein and minerals arestill high. It is well known that tuna is a good source of polyunsaturated fatty acid (PUFA, including Eicosapentaenoicacid (EPA and Docosahexanoic acid (DHA.People around the world pay more attention to eatingsaladsconsisting of fruits and vegetables, in addition todressing. Generally, mayonnaise, a kind of salad dressing, consists of chicken egg yolk(12-15% and soybean oil (30-65%. Both of these ingredients contain very high saturated fatty acid contents. Therefore, because normal mayonnaise is high in fat content and low in polyunsaturated fatty acid, this product is not ideal for people on a diet or those who are trying to control their weight. Objective: To increase omega-3 through tuna roe substitution and to replace fat content using inulin gel. Methods: Tuna roe was prepared by soaking in galangalsolutionextracted with 95% ethanol for removal fishy/rancidity odor. Inulin powder 45 g was suspended in 55 ml of water before being brought to heat at temperature 80oC for 30min to form a gel and stored at 4oC. Treatment ofmakingomega-3 mayonnaise product was started using 100% tuna roe substitution for egg yolk. Thereafter, inulin gel was added to replace vegetable oil at 0, 25, 50, 75 and 100%. Basic mayonnaise containing egg yolk and 0% inulin gel (100% soy bean oil was used asthecontrol sample. Color and emulsion stability testswere monitored for physical quality. pH value, peroxide value (PV and thiobarbituric acid reactive substances (TBARS were used for chemical qualityanalyses. Total viable

Potential availability of urban wood biomass in Michigan: Implications for energy production, carbon sequestration and sustainable forest management in the U.S.A

International Nuclear Information System (INIS)

MacFarlane, David W.

2009-01-01

Tree and wood biomass from urban areas is a potentially large, underutilized resource viewed in the broader social context of biomass production and utilization. Here, data and analysis from a regional study in a 13-county area of Michigan, U.S.A. are combined with data and analysis from several other studies to examine this potential. The results suggest that urban trees and wood waste offer a modest amount of biomass that could contribute significantly more to regional and national bio-economies than it does at present. Better utilization of biomass from urban trees and wood waste could offer new sources of locally generated wood products and bio-based fuels for power and heat generation, reduce fossil fuel consumption, reduce waste disposal costs and reduce pressure on forests. Although wood biomass generally constitutes a 'carbon-neutral' fuel, burning rather than burying urban wood waste may not have a net positive effect on reducing atmospheric CO 2 levels, because it may reduce a significant long term carbon storage pool. Using urban wood residues for wood products may provide the best balance of economic and environmental values for utilization

Corporate performance and the measures of value added

Directory of Open Access Journals (Sweden)

T. Petravičius

2008-09-01

Full Text Available In recent years, managers have turned their attention to the ways increasing the value of their companies. A number of competing measures have been developed and marketed by investment and consulting firms. This paper considers the ways in which value can be created or destroyed in a firm and looks at how to calculate the cost of capital used to measure the opportunity cost of investing funds in one particular business instead of others with equivalent risk. Next, we have a look at the four most widely used value enhancement measures including Economic Value Added, Cash Flow Return on Investment, Market Value Added, Cash Value Added and use an example to think of where these approaches yield similar results and where differences might occur. In conclusion, we summarize the new or unique points in these competing measures, establish the information they can give and explain how to use it when managing and creating shareholder value.

Request for wood samples

NARCIS (Netherlands)

NN,

1977-01-01

In recent years the wood collection at the Rijksherbarium was greatly expanded following a renewed interest in wood anatomy as an aid for solving classification problems. Staff members of the Rijksherbarium added to the collection by taking interesting wood samples with them from their expeditions

Application of industrial wood residues for combined heat and power production

International Nuclear Information System (INIS)

Majchrzycka, A.

2015-01-01

The paper discusses combined production of heat and power (CHP) from industrial wood residues. The system will be powered by wood residues generated during manufacturing process of wooden floor panels. Based on power and heat demands of the plant and wood residues potential, the CHP system was selected. Preliminary analysis of biomass conversion in CHP system and environmental impact was performed.

Effective technology of wood and gaseous fuel co-firing for clean energy production

International Nuclear Information System (INIS)

Zake, M.; Barmina, I.; Gedrovics, M.; Desnickis, A.

2007-01-01

The main aim of the study was to develop and optimise a small-scale experimental co-firing technique for the effective and clean heat energy production by replacing a proportion of fossil fuel (propane) with renewable one (wood biomass). Technical solutions of propane co-fire presenting two different ways of additional heat supply to the wood biomass are proposed and analysed. The experiments have shown that a better result can be obtained for the direct propane co-fire of the wood biomass, when the rate of wood gasification and the ignition of volatiles are controlled by additional heat energy supply to the upper portion of wood biomass. A less effective though cleaner way of heat energy production is the direct propane co-fire of volatiles when low-temperature self-sustaining burnout of the wood biomass controls the rate of the volatile formation, while additional heat energy supply to the flow of volatiles controls their burnout. The effect of propane co-fire on the heat production rate and the composition of polluting emissions is studied and analysed for different rates of the additional heat supply to the wood biomass and of the swirling air supply as well as for different charge of wood biomass above the inlet of the propane flame flow. (Authors)

PRODUCTION OF MANGIUM (Acacia mangium WOOD VINEGAR AND ITS UTILIZATION

Directory of Open Access Journals (Sweden)

Tjutju Nurhayati

2005-03-01

Full Text Available Production  of  wood vinegar from mangium (Acacia  mangium wood bolts/pieces  with their diameter of 3  17 cm, length of 30  67 cm, moisture content of 84.4%, and specific gravity of 0.52 conducted in a dome-shaped kiln with 1.2 m'-capacity afforded a yield of 40.3%.   The mangium wood vinegar was produced  through condensation  (cooling of  smoke/gas fractions released during the charcoaling (carbonization process  of  mangium wood.    The  process  could be regarded  as an integrated production of wood vinegar and charcoal.  The yield of wood vinegar combined with the resulting charcoal was 73.9%  based on  the dry weight of  inputed  mangium wood.    Results of chromatography analysis on mangium wood vinegar as conducted in Japan revealed its organic acid content at 73.9 ppm, phenol content 8.09 ppm, methanol 3.34 ppm, acidity degree 4.91  ppm, and pH 3.89.   Similar analysis on the mangium wood vinegar was conducted in Indonesia's laboratories, and the results were comparable with  those  of  Japan.     Results of  inhibition  testings  on  particular microorganisms   (i.e.  Pseudomonas  aerogjnosa,  Stafi/ococms   attreus,  and  Candidi   albicans  fimgz indicated that the mangium wood vinegar could inflict antirnicrobe action on those microorganism with its effectiveness somewhat below that of  liquid betel soap which could be purchased  from drugstores.  The experimental use of mangium wood vinegar at 3-5% concentration on ginger (Zingiber officinale var. white ginger plants revealed significantly positive growth responses/  characteristics with respect to their height, leaf length, and sprout/ shoot development, in comparison with the untreated ginger plants (control.   Such responses/characteristics were not significantly different from those using atonik's growth hormone.  Likewise, the preliminary use of mangium wood vinegar at 2-percent concentration on teak

The water footprint of wood for lumber, pulp, paper, fuel and firewood

Science.gov (United States)

Schyns, Joep F.; Booij, Martijn J.; Hoekstra, Arjen Y.

2017-09-01

This paper presents the first estimate of global water use in the forestry sector related to roundwood production for lumber, pulp, paper, fuel and firewood. For the period 1961-2010, we estimate forest evaporation at a high spatial resolution level and attribute total water consumption to various forest products, including ecosystem services. Global water consumption for roundwood production increased by 25% over 50 years to 961 × 109 m3/y (96% green; 4% blue) in 2001-2010. The water footprint per m3 of wood is significantly smaller in (sub)tropical forests compared to temperate/boreal forests, because (sub)tropical forests host relatively more value next to wood production in the form of other ecosystem services. In terms of economic water productivity and energy yield from bio-ethanol per unit of water, roundwood is rather comparable with major food, feed and energy crops. Recycling of wood products could effectively reduce the water footprint of the forestry sector, thereby leaving more water available for the generation of other ecosystem services. Intensification of wood production can only reduce the water footprint per unit of wood if the additional wood value per ha outweighs the loss of value of other ecosystem services, which is often not the case in (sub)tropical forests. The results of this study contribute to a more complete picture of the human appropriation of water, thus feeding the debate on water for food or feed versus energy and wood.

'Ecological value added' in an integrated ecosystem-economy model. An indicator for sustainability

International Nuclear Information System (INIS)

Kratena, Kurt

2004-01-01

This paper sets up an input-output system of the relevant ecosystem flows that determine the carbon cycle in the global ecosystem. Introducing energy as the value added component in the ecosystem allows to calculate ecosystem prices expressed in 'energy values'. Linking the ecosystem with the economy in an integrated input-output model then allows to calculate prices of economic activities and of ecosystem activities. In analogy to the 'Ecological Footprint', where productive land is needed to absorb anthropogenic emissions, in this integrated input-output model additional carbon sinks are introduced for emission absorption. These carbon sinks need solar energy input, i.e. 'ecological value added'. Emission absorption as well as GDP therefore become activities valued in the numeraire of the integrated system, i.e.'energy values'. From that sustainability indicators can be derived

Improved Correction of IR Loss in Diffuse Shortwave Measurements: An ARM Value-Added Product

Energy Technology Data Exchange (ETDEWEB)

Younkin, K; Long, CN

2003-11-01

Simple single black detector pyranometers, such as the Eppley Precision Spectral Pyranometer (PSP) used by the Atmospheric Radiation Measurement (ARM) Program, are known to lose energy via infrared (IR) emission to the sky. This is especially a problem when making clear-sky diffuse shortwave (SW) measurements, which are inherently of low magnitude and suffer the greatest IR loss. Dutton et al. (2001) proposed a technique using information from collocated pyrgeometers to help compensate for this IR loss. The technique uses an empirically derived relationship between the pyrgeometer detector data (and alternatively the detector data plus the difference between the pyrgeometer case and dome temperatures) and the nighttime pyranometer IR loss data. This relationship is then used to apply a correction to the diffuse SW data during daylight hours. We developed an ARM value-added product (VAP) called the SW DIFF CORR 1DUTT VAP to apply the Dutton et al. correction technique to ARM PSP diffuse SW measurements.

Adding Value by FM and CREM in Dutch hospitals

NARCIS (Netherlands)

van der Voordt, D.J.M.; Prevosth, J.; van der Zwart, J.

2012-01-01

Purpose: To explore if and how Dutch hospital managers steer on adding value by well-considered Facility Management (FM) and Corporate Real Estate Management (CREM), which values are leading, and how adding value is being translated into concrete interventions. Methodology: In addition to a review

Durable protection of the surface of wood used outdoors: material constraints, problems and approaches to solutions

Directory of Open Access Journals (Sweden)

Merlin A.

2018-01-01

Full Text Available The aesthetic durability of wooden structures is a major challenge for the use of this material in construction. Wood is used for its technical performances but also for its architectural qualities and its aesthetic perception. The premature aging of the wooden structures is detrimental because these disorders, even if they do not affect the strength of the structures, are mostly irremediable. The surface protection of wood is generally ensured by the use of a finish, whose essential role is to protect wood from climatic aggressions (water, solar radiation, oxygen, .... The secondary wood processing industry consists of a series of manufacturing and processing activities, each containing a portion of the added value of the product. The application of a finish on a wood-based work is usually the last and most visible step in this value chain.In outdoor use, the protection of the wood surface with transparent finishes is not yet sufficiently durable to be able to compete with materials used in industrial carpentry such as PVC or aluminum. Opaque finishes generally provide more durable protection but they mask the appearance of the wood sought by users.With the aim of positioning wood in this construction sector, research on transparent finishes has focused on the efficiency and improvement of the durability of the protection of the surface appearance of structures. Faced with climatic aggressions, the optimum conservation of a structure is not only linked to the performance of the finish but also to the characteristics of the wood material. In particular, in order to fulfill its protective function, the finish film must be able to follow the dimensional variations of the wood it covers without breaking and without detachment. In addition to the criteria for the effectiveness of finishes in the protection of structures, the environmental impact must be considered with increasing attention. Currently, more than 80% of composite or solid wood

Calorific value of Prosopis africana and Balanites aegyptiaca wood: Relationships with tree growth, wood density and rainfall gradients in the West African Sahel

Energy Technology Data Exchange (ETDEWEB)

Montes, Carmen Sotelo; Weber, John C. [World Agroforestry Centre (ICRAF), Sahel Office, B.P. E 5118 Bamako (Mali); Silva, Dimas Agostinho da; Bolzon de Muniz, Graciela Ines [Universidade Federal do Parana (UFPR), Av. Lothario Meissner, 900, CEP.: 80270-170-Curitiba (Brazil); Garcia, Rosilei A. [Universidade Federal Rural do Rio de Janeiro (UFRRJ), Instituto de Florestas, Departamento de Produtos Florestais, BR 465, km 07, 23890-000, Seropedica, Rio de Janeiro (Brazil)

2011-01-15

Prosopis africana and Balanites aegyptiaca are native tree species in the West African Sahel and provide wood for fuel, construction and other essential products. A provenance/progeny test of each species was established at one relatively dry site in Niger, and evaluated at 13 years. Gross calorific value of the wood was determined for a random sample of trees in each test: gross CV and CVm{sup 3} = gross calorific value in MJ kg{sup -1} and MJ m{sup -3}, respectively. The major objectives were to determine if gross CV was positively correlated with wood density and tree growth, and if gross CV and/or CVm{sup 3} varied with rainfall gradients in the sample region. Provenances were grouped into a drier and more humid zone, and correlations were computed among all trees and separately in each zone. Results indicated that gross CV was not significantly correlated with density in either species. Gross CV was positively correlated with growth of P. africana (but not B. aegyptiaca) only in the drier zone. Gross CVm{sup 3} was positively correlated with growth of both species, and the correlations were stronger in the drier zone. Multiple regressions with provenance latitude, longitude and elevation indicated that provenance means for gross CV increased, in general, from the drier to the more humid zones. Regressions with gross CVm{sup 3} were not significant. Results are compared with earlier research reports from the provenance/progeny tests and with other tropical hardwood species; and practical implications are presented for tree improvement and conservation programs in the region. (author)

Pretreatment and Fractionation of Wheat Straw for Production of Fuel Ethanol and Value-added Co-products in a Biorefinery

Directory of Open Access Journals (Sweden)

Xiu Zhang

2014-08-01

Full Text Available An integrated process has been developed for a wheat straw biorefinery. In this process, wheat straw was pretreated by soaking in aqueous ammonia (SAA, which extensively removed lignin but preserved high percentages of the carbohydrate fractions for subsequent bioconversion. The pretreatment conditions included 15 wt% NH4OH, 1:10 solid:liquid ratio, 65 oC and 15 hours. Under these conditions, 48% of the original lignin was removed, whereas 98%, 83% and 78% of the original glucan, xylan, and arabinan, respectively, were preserved. The pretreated material was subsequently hydrolyzed with a commercial hemicellulase to produce a solution rich in xylose and low in glucose plus a cellulose-enriched solid residue. The xylose-rich solution then was used for production of value-added products. Xylitol and astaxanthin were selected to demonstrate the fermentability of the xylose-rich hydrolysate. Candida mogii and Phaffia rhodozyma were used for xylitol and astaxanthin fermentation, respectively. The cellulose-enriched residue obtained after the enzymatic hydrolysis of the pretreated straw was used for ethanol production in a fed-batch simultaneous saccharification and fermentation (SSF process. In this process, a commercial cellulase was used for hydrolysis of the glucan in the residue and Saccharomyces cerevisiae, which is the most efficient commercial ethanol-producing organism, was used for ethanol production. Final ethanol concentration of 57 g/l was obtained at 27 wt% total solid loading.

Assessment of the wood waste resource and its position in the wood / wood-energy sector - Synthesis

International Nuclear Information System (INIS)

Guinard, Ludovic; Deroubaix, Gerard; Roux, Marie-Lise; Levet, Anne-Laure; Quint, Vincent

2015-04-01

The first objective of this study is to obtain a better knowledge of the 'wood wastes' issue, to propose a photography of the wood waste sector (productions, trades, consumptions), and then to elaborate different prospective scenarios on the use of wood waste volumes while taking into account possible evolutions on the medium or short term of the regulation and market of the wood/wood energy sector. The considered wastes come from industrial production, from the use of wood-based products, and from the end of life of products potentially containing wood. The authors present bibliographical sources and the adopted methodology, briefly describe the 'wood waste' system with its actors, and then report their assessment of wood wastes. They propose a global assessment as well as detailed assessments with respect to waste origins: wood trade and distribution, industries, craft, households and communities, building sector, public and private tertiary sector, packaging. They also address the collection and management of wood wastes by public services, and present the different types of valorisation (panel fabrication, energy, and others). They discuss exports, and then present different scenarios: a trend-based scenario, and two prospective scenarios with a priority to energetic valorisation or to material valorisation of wood wastes. These scenarios are compared

Value added products from microalgae

CSIR Research Space (South Africa)

Naidoo, T

2013-09-01

Full Text Available , feed, pharmaceutical and research industries (Pulz and Gross, 2004). The market for these applications is still emerging, but there have already been new areas of research in microalgal biotechnology to satisfy the new product demands of industry...

How to reconcile wood production and biodiversity conservation? The Pan-European boreal forest history gradient as an "experiment".

Science.gov (United States)

Naumov, Vladimir; Manton, Michael; Elbakidze, Marine; Rendenieks, Zigmars; Priednieks, Janis; Uhlianets, Siarhei; Yamelynets, Taras; Zhivotov, Anton; Angelstam, Per

2018-07-15

There are currently competing demands on Europe's forests and the finite resources and services that they can offer. Forestry intensification that aims at mitigating climate change and biodiversity conservation is one example. Whether or not these two objectives compete can be evaluated by comparative studies of forest landscapes with different histories. We test the hypothesis that indicators of wood production and biodiversity conservation are inversely related in a gradient of long to short forestry intensification histories. Forest management data containing stand age, volume and tree species were used to model the opportunity for wood production and biodiversity conservation in five north European forest regions representing a gradient in landscape history from very long in the West and short in the East. Wood production indicators captured the supply of coniferous wood and total biomass, as well as current accessibility by transport infrastructure. Biodiversity conservation indicators were based on modelling habitat network functionality for focal bird species dependent on different combinations of stand age and tree species composition representing naturally dynamic forests. In each region we randomly sampled 25 individual 100-km 2 areas with contiguous forest cover. Regarding wood production, Sweden's Bergslagen region had the largest areas of coniferous wood, followed by Vitebsk in Belarus and Zemgale in Latvia. NW Russia's case study regions in Pskov and Komi had the lowest values, except for the biomass indicator. The addition of forest accessibility for transportation made the Belarusian and Swedish study region most suitable for wood and biomass production, followed by Latvia and two study regions in NW Russian. Regarding biodiversity conservation, the overall rank among regions was opposite. Mixed and deciduous habitats were functional in Russia, Belarus and Latvia. Old Scots pine and Norway spruce habitats were only functional in Komi. Thus

Identifying hubs and spokes in global supply chains using redirected trade in value added

NARCIS (Netherlands)

Lejour, Arjan; Rojas-Romagosa, Hugo; Veenendaal, Paul

2017-01-01

The increasing importance of global supply chains has prompted the use of analytical tools based on trade in value added - instead of traditional measures in gross value. We use this analytical framework to develop indicators that identify production hubs and supply spokes in global supply chains.

Gasification of Wood and Non-wood Waste of Timber Production as Perspectives for Development of Bioenergy

Science.gov (United States)

Kislukhina, Irina A.; Rybakova, Olga G.

2018-03-01

The article deals with biomass gasification technology using the gasification plant running on wood chips and pellets, produced from essential oils waste (waste of coniferous boughs). During the study, the authors solved the process task of improving the quality of the product gas derived from non-wood waste of timber production (coniferous boughs) due to the extraction of essential oils and the subsequent thermal processing of spent coniferous boughs at a temperature of 250-300°C degrees without oxygen immediately before pelleting. The paper provides the improved biomass gasification process scheme including the grinding of coniferous boughs, essential oil distillation and thermal treatment of coniferous boughs waste and pelletizing.

Exploring the impact of a spatial data infrastructure on value-added resellers and vice versa

CSIR Research Space (South Africa)

Cooper, Antony K

2013-08-01

Full Text Available , Information and Computational Viewpoints of the Reference Model for Open Distributed Processing. Within the Enterprise Viewpoint, we identified six stakeholders, including a Value-added Reseller (VAR), a stakeholder who adds value to an existing product...

Hot water extracted wood fiber for production of wood plastic composites (WPCs)

Science.gov (United States)

Manuel Raul Pelaez-Samaniego; Vikram Yadama; Eini Lowell; Thomas E. Amidon; Timothy L. Chaffee

2013-01-01

Undebarked ponderosa pine chips were treated by hot water extraction to modify the chemical composition. In the treated pine (TP) , the mass was reduced by approximately 20%, and the extract was composed mainly of degradation products of hemicelluloses. Wood flour produced from TP and unextracted chips (untreated pine, UP) was blended with high-density polyethylene (...

DEVELOPMENT OF WOOD-BASED PRODUCTS WORLDWIDE

Directory of Open Access Journals (Sweden)

Marius C. BARBU

2015-12-01

Full Text Available The tendency in recent decades for manufacturing plants of semi-finished products such as composite panels, has been to invest in order to achieve high production capacities (>2,000 m³/day for panels and >3,000 t/day for paper with one line. The trend of concentrating the primary processing capacities and manufacturing wood-based panels will continue for the next few years not only in Europe but in North and South America as well. The ten largest panel manufacturers had a combined manufacturing capacity that exceeded a third of the worldwide production capacity. The financial crisis that started in 2008 has caused the closure of a large number of factories especially in North America and Central Europe. Small- and medium-sized producers will only survive if they will continue to specialize in the manufacture of panel types and sizes (niche products that are “unprofitable” for mega-groups. The installed production capacity worldwide of all wood-based composite panels combined (includes PY, PB, MDF, OSB rose by more than 2.5 times between 1980 and 2005 (225 mil.m³, and continues to increase despite the crises reaching approx. 300 mil.m³ in 2013. The forecast for the coming years varies greatly from continent to continent. In North America and Central Europe, both a consolidation of the available production capacities and the closure of less efficient older lines are expected. The lowest point of the effect of the financial crisis on the building industry seems to have been overcome. The furniture production companies will continue to move from one continent and region to another.

Wood for the trees

Directory of Open Access Journals (Sweden)

Rob Garbutt

2013-10-01

Full Text Available Our paper focuses on the materiality, cultural history and cultural relations of selected artworks in the exhibition Wood for the trees (Lismore Regional Gallery, New South Wales, Australia, 10 June – 17 July 2011. The title of the exhibition, intentionally misreading the aphorism “Can’t see the wood for the trees”, by reading the wood for the resource rather than the collective wood[s], implies conservation, preservation, and the need for sustaining the originating resource. These ideas have particular resonance on the NSW far north coast, a region once rich in rainforest. While the Indigenous population had sustainable practices of forest and land management, the colonists deployed felling and harvesting in order to convert the value of the local, abundant rainforest trees into high-value timber. By the late twentieth century, however, a new wave of settlers launched a protest movements against the proposed logging of remnant rainforest at Terania Creek and elsewhere in the region. Wood for the trees, curated by Gallery Director Brett Adlington, plays on this dynamic relationship between wood, trees and people. We discuss the way selected artworks give expression to the themes or concepts of productive labour, nature and culture, conservation and sustainability, and memory. The artworks include Watjinbuy Marrawilil’s (1980 Carved ancestral figure ceremonial pole, Elizabeth Stops’ (2009/10 Explorations into colonisation, Hossein Valamanesh’s (2008 Memory stick, and AñA Wojak’s (2008 Unread book (in a forgotten language. Our art writing on the works, a practice informed by Bal (2002, Muecke (2008 and Papastergiadis (2004, becomes a conversation between the works and the themes or concepts. As a form of material excess of the most productive kind (Grosz, 2008, p. 7, art seeds a response to that which is in the air waiting to be said of the past, present and future.

Adding value to laboratory medicine: a professional responsibility.

Science.gov (United States)

Beastall, Graham H

2013-01-01

Laboratory medicine is a medical specialty at the centre of healthcare. When used optimally laboratory medicine generates knowledge that can facilitate patient safety, improve patient outcomes, shorten patient journeys and lead to more cost-effective healthcare. Optimal use of laboratory medicine relies on dynamic and authoritative leadership outside as well as inside the laboratory. The first responsibility of the head of a clinical laboratory is to ensure the provision of a high quality service across a wide range of parameters culminating in laboratory accreditation against an international standard, such as ISO 15189. From that essential baseline the leadership of laboratory medicine at local, national and international level needs to 'add value' to ensure the optimal delivery, use, development and evaluation of the services provided for individuals and for groups of patients. A convenient tool to illustrate added value is use of the mnemonic 'SCIENCE'. This tool allows added value to be considered in seven domains: standardisation and harmonisation; clinical effectiveness; innovation; evidence-based practice; novel applications; cost-effectiveness; and education of others. The assessment of added value in laboratory medicine may be considered against a framework that comprises three dimensions: operational efficiency; patient management; and patient behaviours. The profession and the patient will benefit from sharing examples of adding value to laboratory medicine.

ECONOMIC VALUE ADDED SEBAGAI UKURAN KEBERHASILAN KINERJA MANAJEMEN PERUSAHAAN

Directory of Open Access Journals (Sweden)

Lisa Linawati Utomo

1999-01-01

Full Text Available The company's performance is mostly measured by analysis based on the financial ratio for a specific period. This type of measurement is highly dependent upon the accounting methods used in preparing the financial statement. Therefore a company's performance often looks good and improving overtime, but in reality its performance is deteriorating. The unreliable accounting measure needs an improved performance measure that will recognize and encourage management actions and strategies to increase the overall value of the company and ultimately to punish any activity that reduce value. The introduction of Economic Value Added (EVA has been very relevant recently because based on its definition, EVA measures the amount of value added created by specific action or strategy taken in a company. EVA is also used in the process of goal setting, capital budgeting, performance assessment, and most importantly, incentive compensation within a company. Its implication to the overall being of a company is so important these days that it should not be overlooked when companies plan their strategies. Abstract in Bahasa Indonesia : Kinerja sebuah perusahaan lebih banyak diukur berdasarkan rasio-rasio keuangan selama satu periode tertentu. Pengukuran berdasarkan rasio keuangan ini sangatlah bergantung pada metode atau perlakuan akuntansi yang digunakan dalam menyusun laporan keuangan perusahaan. Sehingga seringkali kinerja perusahaan terlihat baik dan meningkat, yang mana sebenarnya kinerja tidak mengalami peningkatan dan bahkan menurun. Diperlukannya suatu alat ukur kinerja yang menunjukkan prestasi manajemen sebenarnya dengan tujuan untuk mendorong aktivitas atau strategi yang menambah nilai ekonomis (value added activities dan menghapuskan aktivitas yang merusak nilai (non-value added activities. Economic Value Added (EVA sangat relevan dalam hal ini karena EVA dapat mengukur kinerja (prestasi manajemen berdasarkan besar kecilnya nilai tambah yang diciptakan

EU mitigation potential of harvested wood products.

Science.gov (United States)

Pilli, Roberto; Fiorese, Giulia; Grassi, Giacomo

2015-12-01

The new rules for the Land Use, Land Use Change and Forestry sector under the Kyoto Protocol recognized the importance of Harvested Wood Products (HWP) in climate change mitigation. We used the Tier 2 method proposed in the 2013 IPCC KP Supplement to estimate emissions and removals from HWP from 1990 to 2030 in EU-28 countries with three future harvest scenarios (constant historical average, and +/-20% in 2030). For the historical period (2000-2012) our results are consistent with other studies, indicating a HWP sink equal on average to -44.0 Mt CO 2 yr -1 (about 10% of the sink by forest pools). Assuming a constant historical harvest scenario and future distribution of the total harvest among each commodity, the HWP sink decreases to -22.9 Mt CO 2 yr -1 in 2030. The increasing and decreasing harvest scenarios produced a HWP sink of -43.2 and -9.0 Mt CO 2 yr -1 in 2030, respectively. Other factors may play an important role on HWP sink, including: (i) the relative share of different wood products, and (ii) the combined effect of production, import and export on the domestic production of each commodity. Maintaining a constant historical harvest, the HWP sink will slowly tend to saturate, i.e. to approach zero in the long term. The current HWP sink will be maintained only by further increasing the current harvest; however, this will tend to reduce the current sink in forest biomass, at least in the short term. Overall, our results suggest that: (i) there is limited potential for additional HWP sink in the EU; (ii) the HWP mitigation potential should be analyzed in conjunction with other mitigation components (e.g. sink in forest biomass, energy and material substitution by wood).

VALUE-ADDED TAX AND ITS EFFICIENCY: EU–28 AND TURKEY

Directory of Open Access Journals (Sweden)

Sabina Hodzic

2017-06-01

Full Text Available This paper analyses value-added tax (VAT, with special emphasis on efficiency in the EU-28 Member States and Turkey, over the period from 2009 to 2013. From the results of the analysis, we concluded that, the highest efficiency ratio (50.8 was recorded in Croatia in 2013. This indicates that Croatia’s value-added tax revenues as percentage of gross domestic product in the state budget were very high (12.7 in comparison to Turkey’s (9.0 in 2013. As such, VAT is one of the most important taxes in the EU-28 Member States and many countries worldwide, like Turkey. The current VAT system in EU-28 Member States and Turkey is quite complex for the growing number of businesses operating cross-border. To increase investment, competitiveness and growth, an action plan on VAT is proposed for the creation of a single VAT area. The VAT system needs to be more efficient and simpler for businesses to use.

The value added of accountancy programs: a study in the Southeast of Brazil

Directory of Open Access Journals (Sweden)

Silvana Cristina dos Santos

2015-03-01

Full Text Available In recent years, the accounting profession has gone through different changes. The role of accountants in society has evolved, making their function more sophisticated and turning their academic background fundamental to execute tasks in companies. In that context, this paper aims to identify the factors that explain the Value Added of higher education institutions to Accountancy students. Therefore, the results of the specific knowledge test, part of the National Student Performance Examination (Enade 2009, were used, based on a sample of 251 Accountancy programs from the Southeast. In the empirical analysis of the data, descriptive statistics and the linear regression model were used. Based on the valued added method, the Production Function theory was applied, controlling for the students’ individual and socioeconomic characteristics. The results suggest that the main determinants of the Value Added are as follows: the existence of a teaching plan, the number of students receiving grants and the size of the student group.

REGIONAL CHAINS OF ADDED VALUE AS A TOOL OF INDUSTRIAL COOPERATION- COMPETITIVENESS

Directory of Open Access Journals (Sweden)

M. E. Guliyev

2017-01-01

Full Text Available Objectives. The infrastructural aspects of integrated interaction and factors impacting on the efficiency increase of regional participation  in the creation of added value chains on the example of cooperation  between developed and developing countries during the  implementation of joint production projects are considered.Methods. A factor analysis of the degree of various countries’ involvement into global added value chains is carried out,  taking into account their geographical location, natural resources and openness of markets, as well as the infrastructure, professional knowledge of the workforce, practice of cooperation of  domestic firms with foreign partners and the attractiveness of their investment climate.Results. An evaluation of the integrated potential of individual countries, which could undertake the functions of  integrators and mediators within the implementation of regional  programmes of social and economic development, is presented. The  growth potential is estimated and the role of global creation chains  of added value (AVC revealed as a tool for increasing the  competitiveness of national trade policies. It is determined that,  when adopting the latest technologies, companies strive to geographically approximate the placement of the middle links of added value chains to specialised suppliers, “smart” consumers and scientific centres as a means of maintaining innovation continuity.Conclusion. The countries of the EEU and the CIS have significant potential for developing cooperation in the field of  transition to a model of new economic growth, as well as in the  development and application of regional added value chains. As well  as the extractive sector of the economy of the EEU and CIS  countries, included in the regional added value chains, agriculture, chemical and textile industries, metallurgy, transport  engineering, and services sector have the potential to be key

Towards an Integrated Value Adding Management Model for FM and CREM

DEFF Research Database (Denmark)

Jensen, Per Anker; van der Voordt, Theo

2016-01-01

Purpose : To present an integrated process model of adding value by Facilities Management (FM) and Corporate Real Estate Management (CREM) that is a generalisation of existing conceptual frameworks and aims to be a basis for management of added value in practice. Background : The growing research...... frameworks are too complex and lack of common terminology and clear operationalisations of intervention-impact relationships. Approach (Theory/Methodology) :A generalised Value Adding Management process model is developed based on a common cause-effect model identified in existing conceptual frameworks...... aims at supporting the practical management and measurement of added value. A typology with six types of FM/CREM interventions is developed from earlier research. The concept of Value Adding Management is investigated and the 12 most important added value parameters are identified. Research limitations...

Development of a Tool to Measure the Effectiveness of Kaizen Events within the Wood Products Industry

OpenAIRE

Erdogan, Sevtap

2015-01-01

Kaizen implementation and other continuous improvement practices can be used by companies to lower manufacturing costs and increase product value. Kaizen activities are one way that wood products companies can increase their competitiveness. Being able to measure the effectiveness of Kaizen events is important to factors that contribute to Kaizen effectiveness as well as identifying the success of Kaizen implementation. However, little research has focused on the implementation of Kaizen and ...

Reflecting on future research concerning the added value of FM

DEFF Research Database (Denmark)

Jensen, Per Anker; van der Voordt, Theo; Coenen, Christian

2014-01-01

on contributions to the recently published book “The Added Value of Facilities Management” and related future studies, as well as further exploration of five main themes. Findings – Added value is expected to be central in the future development of FM, which is confirmed by recent foresight studies....... There is a need for a better understanding of alignment between FM and core business, performance measurement methods and how models such as the FM Value Map can be of value to the involved stakeholders. Corporate social responsibility (CSR), sustainability and branding have great potential to add value......Purpose – This paper aims to summarize recent research findings and reflections on The Added Value of Facilities Management (FM) and to outline perspectives for future research and development of the added value of FM. Design/methodology/approach – The article is based on reflections...

5000 sustainable workplaces - Wood energy provides work; Holzenergie schafft Arbeit. 5000 nachhaltige Arbeitsplaetze

Energy Technology Data Exchange (ETDEWEB)

Keel, A.

2009-07-01

This article presents the results of a study made by the Swiss Wood Energy Association on the regional and national added value resulting from large wood-fired installations in Switzerland. The number of workplaces created by these installations is also noted. Wood energy is quoted as not only being a way of using forest wastes but also as being a creator of employment. Large wood-fired heating installations are commented on and efforts to promote this type of energy supply even further are discussed. The study indicates which professions benefit from the use of wood energy and quantifies the number of workplaces per megawatt of installed power that result.

Production of wood fuels from young forests

International Nuclear Information System (INIS)

Korpilahti, A.

1998-01-01

National forest invention data shows that more than 200 000 ha of thinnings should be carried out annually. The stemwood accumulation corresponding to this is about 13 million m 3 . The share of industrial wood is about 5.7 million m 3 , so the energy wood potential is about 7.0 million m 3 . Because the growing stock can use the nutrients liberated from logging residues the topwood mass should not be totally harvested, and at the barren areas it should not be harvested at all. Even the difficult terrain restricts in some extent the harvesting of logging residues. After these reductions the economically harvestible energy wood potential has been estimated to be 5.1 million m 3 corresponding to about 0.9 million toe. The amount of first thinnings has during the last few years been only about one third of the need. The accumulation in the first thinning phase could be about 40-80 m 3 /ha. The annual young stand treatment area has usually been about 200 000 ha, but during the last few years it has remained to a little over 100 000 ha. Harvesting of wood fuels from young stands, based on a lot-chipping method and the traditional production chains, was investigated in the national Bioenergy Research Programme. Equipment of suitable size and price are needed for harvesting of small-diameter trees. The profitability of mechanized harvesting can be improved significantly if the single-tree processing is replaced with multi- tree processing. Multi-tree harvesting can be carried out in all production chains, felling-bunching, in partial and pulpwood harvesting, as well as with bare felling machines and harvesters. About 60 % of the stems were processed with a prototype machine, tested in treatment of young forests. About 70 % of fellings in felling-bunching, already in commercial use, was processed as multi- tree processing, and about 80 % in the partial-tree harvesting. The felling of pulpwood as partial trees was about 25-30 % faster as multi-tree processing than with

The economic impact of reduced value added tax rates for groceries

Directory of Open Access Journals (Sweden)

Slavomíra Martinková

2016-12-01

Full Text Available The value added tax represents one of the most important sources of state budget revenues of EU Member States. The basic value added tax rate is in the EU currently between 15% in Luxembourg to 27% applied in Hungary. The revenues from this tax represent an average of 17.5% of all tax revenues of EU countries and create an average GDP of 7.0% (year 2016, EU 28. As revenues from value added tax represent a stable income of state budget, the legislative changes in the system of value added tax, mainly its reductions as well as its imposition on groceries, can significantly influence further macroeconomic development. In the last year, the government of the Slovak Republic implemented changes in universal indirect taxing in such way that in addition to the standard value added tax rate of 20%, the Act No. 268/2015 on Value added tax adopted in 2016 a decreased value added tax rate of 10% on selected groceries, in order to support domestic producers and reduce the tax burden of low-income and middle-income groups. According to the European Commission (2007, the reduced rate of value added tax in selected cases has its justification and importance in the country's economy. The aim of this paper is to analyse the economic impact of the applied reduced value added tax on food in the Slovak Republic in the context of household expenditures and revenues of the state budget.

Lipid metabolism and potentials of biofuel and high added-value oil production in red algae.

Science.gov (United States)

Sato, Naoki; Moriyama, Takashi; Mori, Natsumi; Toyoshima, Masakazu

2017-04-01

Biomass production is currently explored in microalgae, macroalgae and land plants. Microalgal biofuel development has been performed mostly in green algae. In the Japanese tradition, macrophytic red algae such as Pyropia yezoensis and Gelidium crinale have been utilized as food and industrial materials. Researches on the utilization of unicellular red microalgae such as Cyanidioschyzon merolae and Porphyridium purpureum started only quite recently. Red algae have relatively large plastid genomes harboring more than 200 protein-coding genes that support the biosynthetic capacity of the plastid. Engineering the plastid genome is a unique potential of red microalgae. In addition, large-scale growth facilities of P. purpureum have been developed for industrial production of biofuels. C. merolae has been studied as a model alga for cell and molecular biological analyses with its completely determined genomes and transformation techniques. Its acidic and warm habitat makes it easy to grow this alga axenically in large scales. Its potential as a biofuel producer is recently documented under nitrogen-limited conditions. Metabolic pathways of the accumulation of starch and triacylglycerol and the enzymes involved therein are being elucidated. Engineering these regulatory mechanisms will open a possibility of exploiting the full capability of production of biofuel and high added-value oil. In the present review, we will describe the characteristics and potential of these algae as biotechnological seeds.

Bioenergy research programme. Yearbook 1996. Production of wood fuels; Bioenergian tutkimusohjelma. Vuosikirja 1996. Puupolttoaineiden tuotantotekniikka

Energy Technology Data Exchange (ETDEWEB)

Nikku, P [ed.

1997-12-01

The aim of the programme is to increase the use of economically profitable and environmentally sound bioenergy by improving the competitiveness of present peat and wood fuels. Research and development projects will also develop new economically competitive biofuels, new equipment and methods for production, handling and utilisation of biofuels. The total funding for 1996 was 27.3 million FIM and the number of projects 63. The number of projects concerning wood fuels production was 36. The main goals of the research are to develop new production methods for wood fuels in order to decrease the production costs to the level of imported fuels (100 km distance). The second goal is to decrease the small scale production costs by 20 % as compared with the 1992 technology level. Also, new harvesting technology and new work methods will be developed for forest owners and small-entrepreneurs in the course of the programme. Results of the projects carried out in 1996 in this programme are presented in this publication. The integrated harvesting methods, which supply both raw material to wood products industry and wood fuel for energy production, have been chosen the main research areas because they seem to be most promising. Most of the projects are focused in the wood fuel production from first thinnings and from final fellings. The projects broadly covered the research area focusing from material flows, productivity studies, basic wood properties to several case studies. The follow up project of Evaluation-drum chipper was completed with good fuel quality and productivity results. Also the large Forest Energy Project of Central Finland was completed. The project was a significant technology transfer and information dissemination project. (orig.)

24 CFR 3280.308 - Formaldehyde emission controls for certain wood products.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Formaldehyde emission controls for certain wood products. 3280.308 Section 3280.308 Housing and Urban Development Regulations Relating to... Body and Frame Construction Requirements § 3280.308 Formaldehyde emission controls for certain wood...

Value added intellectual coefficient (VAIC: an empirical study

Directory of Open Access Journals (Sweden)

Mehrnaz Paknezhad

2012-04-01

Full Text Available There is no doubt that conventional accounting does not provide actual value of a firm since they only take into account the tangible assets. Intellectual capital provides a new concept for considering actual value of the assets, which helps calculate intangible values of the firm. In this paper, we use value added intellectual coefficient (VAIC to measure the performance of a firm. The study investigates the relationship between intellectual capital and return on assets and value added for three consecutive years between 2008 and 2010. The results indicate that there is no meaningful relationship between intellectual capital and return on assets for fiscal years of 2008 and 2009 but there is a meaningful relationship between these two items for the fiscal year of 2010 when . Our findings also indicate that there is no meaningful relationship between intellectual capital and value added for the years of 2008 and 2010 but there is a meaningful relationship between the items for the fiscal year of 2009. The results somewhat confirm the recently published results in the literature, which argues the use of VAIC for assessing the direct impact of IC on other financial factors.

The added value of a water footprint approach: Micro- and macroeconomic analysis of cotton production, processing and export in water bound Uzbekistan

Science.gov (United States)

Rudenko, I.; Bekchanov, M.; Djanibekov, U.; Lamers, J. P. A.

2013-11-01

Since independence from the former Soviet Union in 1991, Uzbekistan is challenged to consolidate its efforts and identify and introduce suitable agricultural policies to ease the threat of advancing land, water and ecosystem deterioration. On the one hand, irrigated cotton production provides income, food and energy sources for a large part of the rural households, which accounts for about 70% of the total population. On the other hand, this sector is considered a major driver of the on-going environmental degradation. Due to this dual nature, an integrated approach is needed that allows the analyses of the cotton sector at different stages and, consequently, deriving comprehensive options for action. The findings of the economic based value chain analysis and ecologically-oriented water footprint analysis on regional level were complemented with the findings of an input-output model on national level. This combination gave an added value for better-informed decision-making to reach land, water and ecosystem sustainability, compared to the individual results of each approach. The synergy of approaches pointed at various options for actions, such as to (i) promote the shift of water use from the high water consuming agricultural sector to a less water consuming cotton processing sector, (ii) increase overall water use efficiency by expanding the highly water productive industrial sectors and concurrently decreasing sectors with inefficient water use, and (iii) reduce agricultural water use by improving irrigation and conveyance efficiencies. The findings showed that increasing water use efficiency, manufacturing products with higher value added and raising water users' awareness of the real value of water are essential for providing water security in Uzbekistan.

The principal axis approach to value-added calculation.

OpenAIRE

He, Q.; Tymms, P.

2014-01-01

The assessment of the achievement of students and the quality of schools has drawn increasing attention from educational researchers, policy makers, and practitioners. Various test-based accountability and feedback systems involving the use of value-added techniques have been developed for evaluating the effectiveness of individual teaching professionals and schools. A variety of models have been employed for calculating value-added measures, including the use of linear regression models whic...

How Can Value-Added Measures Be Used for Teacher Improvement? What We Know Series: Value-Added Methods and Applications. Knowledge Brief 13

Science.gov (United States)

Loeb, Susanna

2013-01-01

The question for this brief is whether education leaders can use value-added measures as tools for improving schooling and, if so, how to do this. Districts, states, and schools can, at least in theory, generate gains in educational outcomes for students using value-added measures in three ways: creating information on effective programs, making…

Recent progress in the development of solid catalysts for biomass conversion into high value-added chemicals

Science.gov (United States)

Hara, Michikazu; Nakajima, Kiyotaka; Kamata, Keigo

2015-06-01

In recent decades, the substitution of non-renewable fossil resources by renewable biomass as a sustainable feedstock has been extensively investigated for the manufacture of high value-added products such as biofuels, commodity chemicals, and new bio-based materials such as bioplastics. Numerous solid catalyst systems for the effective conversion of biomass feedstocks into value-added chemicals and fuels have been developed. Solid catalysts are classified into four main groups with respect to their structures and substrate activation properties: (a) micro- and mesoporous materials, (b) metal oxides, (c) supported metal catalysts, and (d) sulfonated polymers. This review article focuses on the activation of substrates and/or reagents on the basis of groups (a)-(d), and the corresponding reaction mechanisms. In addition, recent progress in chemocatalytic processes for the production of five industrially important products (5-hydroxymethylfurfural, lactic acid, glyceraldehyde, 1,3-dihydroxyacetone, and furan-2,5-dicarboxylic acid) as bio-based plastic monomers and their intermediates is comprehensively summarized.

Measuring the added value of IT in construction firms

NARCIS (Netherlands)

Laan, Albertus; Voordijk, Johannes T.; Kolkman, S.; Greenwood, D.J.

2003-01-01

The added value of information technology (IT) varies widely along firms. The objective of this paper is to analyse the underlying factors that enlarge or reduce the added value of information systems and IT-applications in construction firms. By applying the process-oriented approach of Tallon et

From failure to value: economic valuation for a selected set of products and services from Mediterranean forests

Directory of Open Access Journals (Sweden)

Davide Pettenella

2016-04-01

Full Text Available Aim of study: the paper estimates the economic value of a selected range of forest products and services, i.e. roundwood, non-wood forest products (NWFPs, and carbon-related services.Area of study: the research covers 21 Mediterranean countries, distinguished into four sub-regions.Material and methods: data have been gathered from official statistical sources (e.g. FAOSTAT, scientific literature and technical reports. Different estimation approaches based on market-price have been used for different products/services.Main results: the estimated value ranges between €10,512 and €11,158 million (M. Wood products represent more than 85% of the total value. Within them, industrial timber is the most relevant component (65%. Figures for NWFPs are likely to be underestimated because data are available only for some products and countries. When using alternative estimates for pine nuts, pine resin and cork, figures show a €36.8-572 M increase. In geographical terms, the economic value of Mediterranean forests is highly concentrated: North-West Mediterranean countries account for 70%, and nearly 90% is in just four countries (France, Spain, Turkey and Italy.Research highlights: enhancing the offer of Mediterranean forest products and increasing their role in the rural economy could help to reduce the costs of forest protection: a well-structured forest economy ensuring stable flows of incomes can provide a fundamental set of public non-market services and social values to both local people and the whole community. Understanding the true value of natural resources, then, is an essential step for promoting their protection and sustainable use.Abbreviations: Bln: billion; CUM: cubic meter; EM: East Mediterranean; FAO: Food and Agriculture Organisation of the United Nations; FRA: Forest Resource Assessment; ha: hectare; M: million; NEM: North-East Mediterranean; NWFP: non-wood forest product; NWM: North-West Mediterranean; SM: South Mediterranean. 

Shell cracking strength in almond (Prunus dulcis [Mill.] D.A. Webb.) and its implication in uses as a value-added product.

Science.gov (United States)

Ledbetter, C A

2008-09-01

Researchers are currently developing new value-added uses for almond shells, an abundant agricultural by-product. Almond varieties are distinguished by processors as being either hard or soft shelled, but these two broad classes of almond also exhibit varietal diversity in shell morphology and physical characters. By defining more precisely the physical and chemical characteristics of almond shells from different varieties, researchers will better understand which specific shell types are best suited for specific industrial processes. Eight diverse almond accessions were evaluated in two consecutive harvest seasons for nut and kernel weight, kernel percentage and shell cracking strength. Shell bulk density was evaluated in a separate year. Harvest year by almond accession interactions were highly significant (p0.01) for each of the analyzed variables. Significant (p0.01) correlations were noted for average nut weight with kernel weight, kernel percentage and shell cracking strength. A significant (p0.01) negative correlation for shell cracking strength with kernel percentage was noted. In some cases shell cracking strength was independent of the kernel percentage which suggests that either variety compositional differences or shell morphology affect the shell cracking strength. The varietal characterization of almond shell materials will assist in determining the best value-added uses for this abundant agricultural by-product.

Value-Added Business Based On Small Scale Of Fisheries A Case Study On Nortern And Shouthern Coasts Of Java Lamongan And Pelabuhanratu Regency Indonesia

Directory of Open Access Journals (Sweden)

Budi Wardono

2015-08-01

Full Text Available The development of fisheries sector is intended to improve the role of creating a strong linkage with other sectors by increasing the value added absorbing labor forces and increasing peoples income so that this can make the economy grow well. The value added is a value that increases due to a commodity that has been processed transported or stored in a production. Lamongan and Pelabuhanratu regencies are one of fisheries centers on the north and the south coast of Java Island. The aim of this research was to know the value added and the business margin of fisheries from the processing and marketing aspects. The research was carried out in two locations Northern coast Lamongan regencies and Shouther coasts Pelabuhanratu regencies Indoneisa. The data used were primary data the people involved in the business including fishing marketing and processing product. The results showed that the process of fisheries product yielded the value added and margin that were created from the incorporation of business benefit added input contribution other input and direct reward for the labor forces. The value added and the business margin of product processing can reach 2 to 3 fold from the main input value. The value added and the business margin of fisheries product processing were very big. This was the source of economy growth there. The effort to develop the business of fisheries product processing in the small scale need to be supported with various programs especially in the market access and funding.

Carbon-Supported Fe Catalysts for CO2 Electroreduction to High-Added Value Products: A DEMS Study: Effect of the Functionalization of the Support

OpenAIRE

Pérez-Rodríguez, S.; García, G.; Calvillo, L.; Celorrio, V.; Pastor, E.; Lázaro, M. J.

2011-01-01

Vulcan XC-72R-supported Fe catalysts have been synthesised for the electroreduction of CO2 to high-added value products. Catalysts were obtained by the polyol method, using ethylene glycol as solvent and reducing agent. Prior to the metal deposition, Vulcan was subjected to different oxidation treatments in order to modify its surface chemistry and study its influence on the physicochemical and electrochemical properties of the catalysts, as well as on the product distribution. The oxidation ...

Wood fuel production technologies in EU countries

Energy Technology Data Exchange (ETDEWEB)

Hakkila, P [Finnish Forest Research Institute, Vantaa (Finland)

1998-12-31

The presentation reviews the major technologies used for the production of fuel chips for heating plants in Europe. Three primary options are considered: production of whole-tree chips from young trees for fuel; integrated harvesting of fiber and energy from thinning based on tree-section system; and production of fuel chips from logging residue in clear-cut areas after fully mechanized logging. The characteristics of the available biomass reserve and proven technology for its recovery are discussed. The employment effects of fuel chip production and the costs of wood fuels are also briefly discussed. (author) 3 refs., 3 figs.

Wood fuel production technologies in EU countries

Energy Technology Data Exchange (ETDEWEB)

Hakkila, P. [Finnish Forest Research Institute, Vantaa (Finland)

1997-12-31

The presentation reviews the major technologies used for the production of fuel chips for heating plants in Europe. Three primary options are considered: production of whole-tree chips from young trees for fuel; integrated harvesting of fiber and energy from thinning based on tree-section system; and production of fuel chips from logging residue in clear-cut areas after fully mechanized logging. The characteristics of the available biomass reserve and proven technology for its recovery are discussed. The employment effects of fuel chip production and the costs of wood fuels are also briefly discussed. (author) 3 refs., 3 figs.

Isolation and characterization of lignin from the oak wood bioethanol production residue for adhesives.

Science.gov (United States)

Lee, Soo Jung; Kim, Hyun Joo; Cho, Eun Jin; Song, Younho; Bae, Hyeun-Jong

2015-01-01

Lignin was isolated from the residue of bioethanol production with oak wood via alkaline and catalyzed organosolv treatments at ambient temperature to improve the purity of lignin for the materials application. The isolated lignins were analyzed for their chemical composition by nitrobenzene oxidation method and their functionality was characterized via wet chemistry method, element analysis, (1)H NMR, GPC and FTIR-ATR. The isolated lignin by acid catalyzed organosolv treatment (Acid-OSL) contained a higher lignin content, aromatic proton, phenolic hydroxyl group and a lower nitrogen content that is more reactive towards chemical modification. The lignin-based adhesives were prepared and the bond strength was measured to evaluate the enhanced reactivity of lignin by the isolation. Two steps of phenolation and methylolation were applied for the modification of the isolated lignins and their tensile strengths were evaluated for the use as an adhesive. The acid catalyzed organosolv lignin-based adhesives had comparable bond strength to phenol-formaldehyde adhesives. The analysis of lignin-based adhesives by FTIR-ATR and TGA showed structural similarity to phenol adhesive. The results demonstrate that the reactivity of lignin was enhanced by isolation from hardwood bioethanol production residues at ambient temperature and it could be used in a value-added application to produce lignin-based adhesives. Copyright © 2014 Elsevier B.V. All rights reserved.

Bacillus aryabhattai BA03: a novel approach to the production of natural value-added compounds.

Science.gov (United States)

Paz, Alicia; Carballo, Julia; Pérez, María José; Domínguez, José Manuel

2016-10-01

A strain designated as BA03, with the ability to transform ferulic acid into vanillin and 4-vinylguaiacol, was isolated from contaminated cryovials. The production of natural value-added compounds was dependent on the media employed. The morphological and physiological characteristics of this strain were compared with those of the typical vanillin-producer strain Amycolatopsis sp. ATCC 39116. According to a partial 16S rRNA sequence, we determined that BA03 belonged to Bacillus aryabhattai. In addition, analysis of the results showed that this strain exhibited interesting enzymatic activity, including cellulases, laccases, lipases and pectinases. In light of this, we propose new functions for this multitasking microorganism. We suggest that it may be used for converting lignocellulosic wastes into byproducts with industrial uses, and also for treating disposal residues such as dyes in the textile industry. Hence, the possibility for novel research with B. aryabhattai opens up in the fields of biodegradation and/or revalorization of wastes.

Production of dry wood chips in connection with a district heating plant

Directory of Open Access Journals (Sweden)

Yrjölä Jukka

2004-01-01

Full Text Available Moisture and its variation in wood chips make the control of burning in small scale heating appliances difficult resulting in emissions and loss of efficiency. If the quality of wood chips would be better, i. e. dried and sieved fuel with more uniform size distribution would be avail able, the burning could be much cleaner and efficiency higher. In addition higher power out put could be obtained and the investment costs of the burning appliances would be lower. The production of sieved and dried wood chip with good quality could be accomplished in connection with a district heating plant. Then the plant would make profit, in addition to the district heat, from the dried wood chips sold to the neighboring buildings and enterprises sep a rated from the district heating net using wood chips in energy production. The peak power of a district heating plant is required only a short time during the coldest days of the winter. Then the excess capacity during the milder days can be used as heat source for drying of wood chips to be marketed. Then wood chips are sieved and the fuel with best quality is sold and the reject is used as fuel in the plant it self. In a larger district heating plant, quality of the fuel does not need to be so high In this paper the effect of moisture on the fuel chain and on the boiler is discussed. Energy and mass balance calculations as a tool of system design is described and the characteristics of proposed dry chips production method is discussed.

Recent advances in the production of value added chemicals and lipids utilizing biodiesel industry generated crude glycerol as a substrate - Metabolic aspects, challenges and possibilities: An overview.

Science.gov (United States)

Vivek, Narisetty; Sindhu, Raveendran; Madhavan, Aravind; Anju, Alphonsa Jose; Castro, Eulogio; Faraco, Vincenza; Pandey, Ashok; Binod, Parameswaran

2017-09-01

One of the major ecological concerns associated with biodiesel production is the generation of waste/crude glycerol during the trans-esterification process. Purification of this crude glycerol is not economically viable. In this context, the development of an efficient and economically viable strategy would be biotransformation reactions converting the biodiesel derived crude glycerol into value added chemicals. Hence the process ensures the sustainability and waste management in biodiesel industry, paving a path to integrated biorefineries. This review addresses a waste to wealth approach for utilization of crude glycerol in the production of value added chemicals, current trends, challenges, future perspectives, metabolic approaches and the genetic tools developed for the improved synthesis over wild type microorganisms were described. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mixture toxicity of wood preservative products in the fish embryo toxicity test.

Science.gov (United States)

Coors, Anja; Dobrick, Jan; Möder, Monika; Kehrer, Anja

2012-06-01

Wood preservative products are used globally to protect wood from fungal decay and insects. We investigated the aquatic toxicity of five commercial wood preservative products, the biocidal active substances and some formulation additives contained therein, as well as six generic binary mixtures of the active substances in the fish embryo toxicity test (FET). Median lethal concentrations (LC50) of the single substances, the mixtures, and the products were estimated from concentration-response curves and corrected for concentrations measured in the test medium. The comparison of the experimentally observed mixture toxicity with the toxicity predicted by the concept of concentration addition (CA) showed less than twofold deviation for all binary mixtures of the active substances and for three of the biocidal products. A more than 60-fold underestimation of the toxicity of the fourth product by the CA prediction was detected and could be explained fully by the toxicity of one formulation additive, which had been labeled as a hazardous substance. The reason for the 4.6-fold underestimation of toxicity of the fifth product could not be explained unambiguously. Overall, the FET was found to be a suitable screening tool to verify whether the toxicity of formulated wood preservatives can reliably be predicted by CA. Applied as a quick and simple nonanimal screening test, the FET may support approaches of applying component-based mixture toxicity predictions within the environmental risk assessment of biocidal products, which is required according to European regulations. Copyright © 2012 SETAC.

Improving functional value of meat products.

Science.gov (United States)

Zhang, Wangang; Xiao, Shan; Samaraweera, Himali; Lee, Eun Joo; Ahn, Dong U

2010-09-01

In recent years, much attention has been paid to develop meat and meat products with physiological functions to promote health conditions and prevent the risk of diseases. This review focuses on strategies to improve the functional value of meat and meat products. Value improvement can be realized by adding functional compounds including conjugated linoneleic acid, vitamin E, n3 fatty acids and selenium in animal diets to improve animal production, carcass composition and fresh meat quality. In addition, functional ingredients such as vegetable proteins, dietary fibers, herbs and spices, and lactic acid bacteria can be directly incorporated into meat products during processing to improve their functional value for consumers. Functional compounds, especially peptides, can also be generated from meat and meat products during processing such as fermentation, curing and aging, and enzymatic hydrolysis. This review further discusses the current status, consumer acceptance, and market for functional foods from the global viewpoints. Future prospects for functional meat and meat products are also discussed.

48 CFR 252.229-7006 - Value added tax exclusion (United Kingdom).

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Value added tax exclusion... CLAUSES Text of Provisions And Clauses 252.229-7006 Value added tax exclusion (United Kingdom). As prescribed in 229.402-70(f), use the following clause: Value Added Tax Exclusion (United Kingdom) (JUN 1997...

Value Added Methods: Moving from Univariate to Multivariate Criteria

Science.gov (United States)

Newman, David; Newman, Isadore; Ridenour, Carolyn; Morales, Jennifer

2014-01-01

The authors describe five value-added methods (VAM) used in school assessment as the backdrop to their main thesis. Then they review the assumptions underlying measurement and evaluation, the foundation of all assessment systems, including value-added. They discuss the traditional criterion variable used in VAM: a standardized test score. Next,…

Measuring Corporate Sustainability and Environmental, Social, and Corporate Governance Value Added

Directory of Open Access Journals (Sweden)

Alena Kocmanová

2016-09-01

Full Text Available The aim of the paper is to propose a model for measuring sustainable value which would complexly assess environmental, social, and corporate governance contribution to value creation. In the paper the concept of the Sustainable Environmental, Social and Corporate Governance Value Added is presented. The Sustainable Environmental, Social and Corporate Governance Value Added is based on the Sustainable Value Added model and combines weighted environmental, social, and corporate governance indicators with their benchmarks determined by Data Envelopment Analysis. Benchmark values of indicators were set for each company separately and determine the optimal combination of environmental, social, and corporate governance inputs to economic outcomes. The Sustainable Environmental, Social and Corporate Governance Value Added methodology is applied on real-life corporate data and presented through a case study. The value added of most of the selected companies was negative, even though economic indicators of all of them are positive. The Sustainable Environmental, Social and Corporate Governance Value Added is intended to help owners, investors, and other stakeholders in their decision-making and sustainability assessment. The use of environmental, social, and corporate governance factors helps identify the company’s strengths and weaknesses, and provides a more sophisticated insight into it than the one-dimensional methods based on economic performance alone.

Creating value added to customers: Marketing and sales role

OpenAIRE

Damnjanović Vesna; Filipović Vinka

2006-01-01

This paper presents the new trends in sales and marketing areas which reshaping markets and changing the way business is done. Marketing and sales management need a well-defined strategy for added value exploration, creation and delivery. The holistic marketing process involves all stakeholders and required them to participate in the value added creation process.

Applying value stream mapping techniques to eliminate non-value-added waste for the procurement of endovascular stents

International Nuclear Information System (INIS)

Teichgräber, Ulf K.; Bucourt, Maximilian de

2012-01-01

Objectives: To eliminate non-value-adding (NVA) waste for the procurement of endovascular stents in interventional radiology services by applying value stream mapping (VSM). Materials and methods: The Lean manufacturing technique was used to analyze the process of material and information flow currently required to direct endovascular stents from external suppliers to patients. Based on a decision point analysis for the procurement of stents in the hospital, a present state VSM was drawn. After assessment of the current status VSM and progressive elimination of unnecessary NVA waste, a future state VSM was drawn. Results: The current state VSM demonstrated that out of 13 processes for the procurement of stents only 2 processes were value-adding. Out of the NVA processes 5 processes were unnecessary NVA activities, which could be eliminated. The decision point analysis demonstrated that the procurement of stents was mainly a forecast driven push system. The future state VSM applies a pull inventory control system to trigger the movement of a unit after withdrawal by using a consignment stock. Conclusion: VSM is a visualization tool for the supply chain and value stream, based on the Toyota Production System and greatly assists in successfully implementing a Lean system.

Added Value of Employee Financial Participation

NARCIS (Netherlands)

Poutsma, F.; Kaarsemaker, E.C.A.; Andresen, M.; Nowak, C.

2015-01-01

This chapter broadens our understanding of the added value of employee financial participation. Financial participation is a generic term for the participation of employees in profit and enterprise results including equity of their employing firm. In general, there are two forms of employee

Exogenous Variables and Value-Added Assessments: A Fatal Flaw

Science.gov (United States)

Berliner, David C.

2014-01-01

Background: There has been rapid growth in value-added assessment of teachers to meet the widely supported policy goal of identifying the most effective and the most ineffective teachers in a school system. The former group is to be rewarded while the latter group is to be helped or fired for their poor performance. But, value-added approaches to…

Creating value added to customers: Marketing and sales role

Directory of Open Access Journals (Sweden)

Damnjanović Vesna

2006-01-01

Full Text Available This paper presents the new trends in sales and marketing areas which reshaping markets and changing the way business is done. Marketing and sales management need a well-defined strategy for added value exploration, creation and delivery. The holistic marketing process involves all stakeholders and required them to participate in the value added creation process.

Exploring Value-Added Options - Opportunities in Mouldings and Millwork

Science.gov (United States)

Bob Smith; Philip A. Araman

1997-01-01

The millwork industry, which includes manufacture of doors, windows, stair parts, blinds, mouldings, picture frame material, and assorted trim, can be a lucrative value-added opportunity for sawmills. Those entering the value-added millwork market often find that it is a great opportunity to generate greater profits from upper grades and utility species, such as yellow...

Interest in energy wood and energy crop production among Finnish non-industrial private forest owners

International Nuclear Information System (INIS)

Raemoe, A.-K.; Jaervinen, E.; Latvala, T.; Toivonen, R.; Silvennoinen, H.

2009-01-01

EU targets and regulations regarding energy production and the reduction of greenhouse gas emissions have been tightening in the 2000s. In Finland the targets are planned to be achieved mainly by increasing the use of biomass. Wood already accounts for a marked proportion of Finnish energy production, but additional reserves are still available. Energy crop production also has considerable potential. Practically all Finnish farmers are also forest owners. Therefore, private forest owners are in a decisive position regarding the supply of energy wood and crops in Finland. In this paper the future supply of biomass is examined according to their past behaviour, intentions and attitudes. Finnish forest owners have a positive attitude towards the use of wood and crops in energy production. Price is becoming more critical as a motive for the supply of energy wood. Recreation and nature conservation play a smaller role than factors related to wood production and forest management as for motives for harvesting energy wood. However, almost a half of forest owners in this study were uncertain of their willingness to supply biomass. This is partly due to limited knowledge of the issues involved in energy wood and agricultural energy crop production and the underdeveloped markets for energy biomass. In order to achieve the targets, supply should be activated by further developing market practices, information, guidance and possibly other incentives for landowners. In general, there is interest among landowners in increasing the supply of energy biomass. However, the growth of supply presumes that production is an economically attractive and competitive alternative, that the markets are better organized than at present, and that more comprehensive information is available about bioenergy and biomass markets and production techniques.

Wood pellet seminar

International Nuclear Information System (INIS)

Aarniala, M.; Puhakka, A.

2001-01-01

The objective of the wood pellet seminar, arranged by OPET Finland and North Karelia Polytechnic, was to deliver information on wood pellets, pellet burners and boilers, heating systems and building, as well as on the activities of wood energy advisors. The first day of the seminar consisted of presentations of equipment and products, and of advisory desks for builders. The second day of the seminar consisted of presentations held by wood pellet experts. Pellet markets, the economy and production, the development of the pellet markets and their problems (in Austria), the economy of heating of real estates by different fuel alternatives, the production, delivery and marketing of wood pellets, the utilization of wood pellet in different utilization sites, the use of wood pellets in detached houses, pellet burners and fireplaces, and conversion of communal real estate houses to use wood pellets were discussed in the presentations. The presentations held in the third day discussed the utilization of wood pellets in power plants, the regional promotion of the production and the use of pellets. The seminar consisted also of visits to pellet manufacturing plant and two pellet burning heating plants

Integrated production method for wood fuel and pulp wood in Northern Finland; Integroitu energiapuun tuotanto-menetelmae Pohjois-Suomessa

Energy Technology Data Exchange (ETDEWEB)

Hooli, A [Hooli Oy, Kemi (Finland); Ranta, T [VTT Energy, Jyvaeskylae (Finland)

1997-12-01

Hooli Oy, operating mainly in the Northern Finland has developed the production method suitable for bunch-processing of small wood. The mobile machine, consisting of delimber-debarker, and fuel fraction crusher units, produces debarked stemwood for pulping industry and branchwood-bark chips for thermal power stations. The basic method has been ready for demonstration and practical applications since in the beginning of year 1996. The objective of the project is to develop a method suitable for bundle processing of small wood, in which the trees are delimbed and debarked, and the formed waste wood is crushed using a machine unit, developed especially for this purpose. The method is based on utilisation of a separate delimbing-debarking unit, which operates separately from the pulpwood transportation chain, so the pulpwood transportations can be done at the proper time either as debarked roundwood or chips. Based on field experiments in 1995 - 1996, to attain the targets of the project looks promising. In 1997 there will happen technical modifications to the machine to improve the debarking results (target < 1 % bark content) of the bolts and to improve the logistic productivity of the whole production chain

Willow wood production on radionuclide polluted areas

Directory of Open Access Journals (Sweden)

Rodkin Oleg I.

2010-01-01

Full Text Available ABSTRACT: One of the key environmental problems in Belarus is effective use of agricultural lands contaminated by radionuclide due to the Chernobyl disaster. The alternative method to traditional agricultural crops is fast growing willow cultivation. It is possible to use biomass of willow as renewable energy source. The goal of our investigation was the estimation of environmental aspects of willow wood production on polluted areas. The field study experiments (2007-2010 were conducted at Krichev district of Mogilev region in eastern Belarus. This region characterized by high level of Cs-137 contamination as well as high level of heavy metals pollution. In the first stage of experiments, the concentration of cesium-137 in different parts of willow biomass had been measured and transfer factor calculated. The measuring had been done for leaves, roots, and wood. To control cesium-137 accumulation in willow biomass we apply different types (nitrogen N, phosphorus P and potassium K and dose of fertilizer. The experiments show that potassium mineral fertilizer is the key factor for radionuclide accumulation control. The optimal dose of potassium is 90 kg per hectare. On the base of experimental results the model of cesium-137 accumulation in the wood for a 21 year has been developed. In accordance with calculation to the end of willow cultivation (21 year concentration of cesium-137 in wood will not be higher than permitted even with the level of cesium-137 contamination in the soil 1480 kBq/m2 (maximum 140 kqB/m2 with permitted level for firewood is 740 Bq/kg.. The concentration of cesium-137 in the roots increases gradually and get maximum in 21 year (3000 kqB/m2. Our results confirm that in the sum about 0.8 million hectares of radionuclide polluted arable lands partly excluded from agricultural practice in Belarus could be used for willow biomass production.

Transitioning Wood Furniture Products towards Sustainability

OpenAIRE

Lu, Lei; Zhang, WeiGuang; Zhang, WeiQing

2008-01-01

Wood Furniture Products (WFPs) play a significant role in both the global economy and the transition of society towards sustainability. This paper begins with a brief description of the industry and highlights the current challenges and compelling measures of WFPs from a systems perspective through the lens of the Framework for Strategic Sustainable Development (FSSD) and by applying backcasting from sustainability principles (SPs). An examination of the challenges and opportunities of WFPs i...

Nutritional Value of Irradiated Animal Feed By-Products

International Nuclear Information System (INIS)

El-Din Farag, M.D.H.

1998-01-01

Animal feed by-products, widely used in animal diets, are sources of disease organisms for animals and for human beings. Salmonella is the principal genus of concern.Radiation treatment (radicidation, radurization) is a promising method of decontamination of feed ingredients. Commercial samples of fish, meat, and blood meals were sealed by heat in polyethylene bags and irradiated at dose levels of 5.0, 10, 20 and 50 kGy. Their chemical analysis were carried out according to A. O. A.C [1] and the total protein efficiency (TPE) of the three animal feed by-products was determined according to Wood ham (2) by using one day old Dokki-4 chicks. Radiation induced an insignificant effect on the chemical constituent of meals. Also, the same trend was observed with TPE of both fish and meat meals. However, irradiation treatments improved TPE values of irradiated blood meal samples. From the results, it could be concluded that irradiation of animal feed by-products up to a dose level of 50 Gy has no adverse effects on the nutritional value of animal feed by-products

Approaching value added planning in the green environment

NARCIS (Netherlands)

Cilliers, E.J.; Timmermans, W.

2013-01-01

Purpose – The purpose of this paper is to link economic value to urban green spaces to enhance the value of green urban spaces, along with the added benefit it can offer to the urban environment. Design/methodology/approach – As part of the VALUE project (Valuing Attractive Landscapes in the Urban

Value added products with popular low grade rice varieties of Andhra Pradesh.

Science.gov (United States)

Anitha, G; Rajyalakshmi, P

2014-12-01

Eight Popular Low Grade Rice Varieties (PLRVs) MTU 3626, MTU 1001, MTU 1010, MTU 4870 and NLR 145, NLR 34242, NLR 30491, NLR 34449, (developed and released by ANGR agricultural University, Andhra Pradesh) having poor cooking quality were selected for the study. ANGRAU variety BPT 5204 popularly consumed as staple rice was used as check. Eight products of traditional/commercial importance were standardized incorporating PLRVs as a major ingredient in the form of rice flour (burfi, noodles and extruded snack product and vennaundalu (butter coated balls), palathalikalu (dough rolled into strips, steamed/cooked in milk); rice semolina (instant kheer mix and instant upma mix), and flaked rice (nutritious bar). The products were evaluated for nutritional, cooking quality characteristics, consumer acceptability and shelf-life. Consumer acceptability of the PLR products was carried out with 60 farm women based on 9 point hedonic scale. Shelf-life of the products (packed in both metalized PP and PE pouches) was evaluated monthly for chemical, microbiological and sensory parameters. Energy values of control and PLR products showed no significant difference. Upon cooking, PLR Noodles showed no significant difference with water absorption and volume but more (p instant kheer mix (92%) and extruded product (88%). As per sensory scores, all the PLR products were well accepted with no observable changes in flavor or taste upon storage. PLR products showed increased (P noodles and highest for burfi (though in safe limits). Extruded snacks (control and PLR) showed no microbial growth during the entire storage period. Considering the poor marketability of PLRVs for consumption as staple rice, the study signifies the utilitarian value of PLRVs in making products of convenience/commercial importance.

Impregnating Systems for Producing Wood-Plastic Composite Materials and Resinified Woods by Radiochemical Means

International Nuclear Information System (INIS)

Laizier, J.; Laroche, R.; Marchand, J.

1969-01-01

The effect of the nature of the components in the impregnation mixture on the characteristics of wood-plastic combinations has been studied in the case of beech by applying a wide variety of compositions. In particular, the effect of water (in the impregnator, and in the form of moisture in the wood) on the characteristics of the products obtained has been determined. It has been shown that, in place of the conventional method for preparing resinified woods (using a ternary monomer-solvent-water mixture), it is possible to use a method involving comonomers, which obviate the need to dry the wood after treatment. The evaluation of the results obtained is based on the value of the impregnation rate and on the modifications in microscopic structure; these emphasize the differences between the types of filler and enable comparisons to be drawn with the dimensional stabilities observed. Measurements of variations in dimensions and the recurrence of moisture have made it possible to establish a classification based on the types of monomer used and the operating conditions. It is shown that a whole range of products is obtained, the properties of which differ widely and are comparatively easily adaptable to the purpose specified. These properties illustrate clearly the differences and characteristics of resinified woods as opposed to conventional wood-plastic materials. (author) [fr

Studies on the preparation of value-added products for limestone

Energy Technology Data Exchange (ETDEWEB)

Chae, Young Bae; Jeong, Soo Bok; Ko, Won Sik; Park, Je Shin; Oh, Jung Whan [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

1997-12-01

Most of limestone in our country was consumed by the cement and iron/steel making industries and the amount of that was up to 72 million ton in 1996. Recently, importation of high grade limestone that have properties of high whiteness and grade are increased with diversification of chemical products and powder as various qualified filler, because high grade limestone are limited and of few deposit in our country. Therefore, the purpose of this study has investigated to raise to high grade by economical processes with low grade of domestic limestone. In this year, first of all, we investigated the status of application utilize and related industries with the domestic limestone, and then being consideration with condition selected the adequate sample from Andong, Jungsun and Kumsan area. Magnetic materials were involved in impurities of sample, so magnetic separation method was applied in elimination of the ferro-magnetic materials and para-magnetic materials, such as chlorite, muscovite, quartz, dolomite, magnetite, feldspar and so on. The limestone sample has many kinds of impurity. Investigation of flotation was undertaken to eliminate impurities from limestone crude ore and the tests were performed to get a optimum condition adding oleic acid as a promoter, sodium silicate and sodium carbonate as a conditioning agents and MIBC as a frother, while to float the sulfide minerals added amyl xanthate as a promoter, and sulfuric acid as a pH regulator. And most of the impurities involving in flotation sink contained such as quartz, chlorite, muscovite, feldspar, dolomite and so on. Selective crushing and classification methods were performed to eliminate impurities depends on the mineral properties and should be the selective crushing methods are very useful at the manufacturing factory of heavy calcium carbonate with the dry milling system. (author). 36 refs., 46 tabs., 33 figs.

Criterion 6, indicator 28 : total and per capita consumption of wood and wood products in round wood equivalents

Science.gov (United States)

James L. Howard; Rebecca Westby; Kenneth E. Skog

2010-01-01

Total consumption of wood and paper products and fuelwood, in roundwood equivalents, increased between 1965 and 1988 from 13.2 to 18.9 billion cubic feet. Since 1988, it has been about 20 billion cubic feet per year. Total per capita consumption increased between 1965 and 1987, from 68 to 83 ft3 per year. Since 1987 through 2006, per capita...

The added value of sustainability motivations in understanding sustainable food choices

OpenAIRE

Verain, M.C.D.; Onwezen, M.C.; Sijtsema, S.J.; Dagevos, H.

2016-01-01

Understanding consumer food choices is crucial to stimulate sustainable food consumption. Food choice motives are shown to be relevant in understanding consumer food choices. However, there is a focus on product motives, such as price and taste, whereas process motives (i.e. environmental welfare) are understudied. The current study aims to add to the existing literature by investigating the added value of sustainable process motives (environmental welfare, animal welfare and social justice) ...

Building for a better hospital. Value-adding management & design of healthcare real estate

Directory of Open Access Journals (Sweden)

Johan van der Zwart

2014-09-01

;
(D the primary process (4, and the design of the building (8. In the integrating framework, the steps at the level of the organisation are completed by the steps of the EFQM model. The strategic, financial, functional and physical perspectives on real estate (5 can be positioned parallel to the stakeholders’ objectives (1 that are described in the EFQM-INK model. In this way stakeholder management is part of the organisational management and is translated into real estate perspectives on CREM. The perspectives on real estate are translated into real estate added values (6 as the common language that in all phases of the real estate lifecycle can be assessed. This concept of adding value by real estate is connected to the key issues for success (2 that result from the demands and wishes of society, employees, customers and the organisation’s management at an organisational level. Both the key issues for success and the added values of real estate provide input into the change management process of the organisation (3 and its real estate (7. The organisation’s change management (3 is directed by leadership and is about policy & management of the resources, including human resources and real estate. In this part of the model, different resources for production have to be balanced against each other. This results in a process that has to be implemented in a physical environment. In this model, the Designing an Accommodation strategy (DAS-Frame is the basis for real estate change management (7. In an iterative process a match is made between demand and supply, now and in the future, resulting in a building which can support organisational primary processes. Paralleling the management of accommodation with organisational change thus leads logically to a step-by-step plan for the transformation of the accommodation. Both the processes and the building are compared with the stakeholder demands and related perspectives on real estate. In addition, a five-point scale

Marketing of non-wood forest products: Case study of the enterprise for forest mushroom processing

Directory of Open Access Journals (Sweden)

Keča Ljiljana

2009-01-01

Full Text Available Under the impact of climate changes it is increasingly obvious that forestry should rely more strongly on the multi­functional character of the managed resources. In addition to wood, there is a series of non­wood products and services offered by forests. Non­wood forest products and services consist of various fruits of forest trees and shrubs, mushrooms, various objects made of non­wood material, and especially forest social services, such as recreation, tourism, hunting, photo­safari, etc. This paper presents a marketing analysis on the example of the enterprise dealing with the purchase, processing and sale of wild mushrooms and products made of mushrooms. The study applies a modern methodological approach implemented in similar researches.

Localized products in France: definition, protection and value-adding

Directory of Open Access Journals (Sweden)

Laurence Bérard

2007-04-01

and variety. To do that, we need to look at the cultural criteria that link a place with a particular history and social group.In addition to formal procedures for the protection of geographical indications, various other initiatives also help to add value to local products. Part of coordinated (but basically unofficial campaigns, they reflect the efforts of players from all walks of life but mainly the public sector (Ministries of Agriculture, Tourism and the Environment.Not all countries have the same relationship with place. A product’s place within a territory is determined by various factors, some more important than others depending on that country’s economic and social history, culture, local balances of power and natural environment.

Leaching of wood ash - Laboratory and field studies; Lakning av vedaska - Laboratorie- och faeltstudier

Energy Technology Data Exchange (ETDEWEB)

Larsson, Per-Erik

2012-02-15

High forest production leads to diminishing amounts of base cations and micro nutrients in forest soils. This is due to uptake in, and harvest of, the trees. Losses can be compensated for by spreading stabilized wood ash on the forest ground, which means recycling of base cations and micro nutrients. Chemical composition of wood ash can easily be described by standard methods in the laboratory. However, this does not include the process of leaching in nature, such as which components and leaching rate for different compounds. During field conditions several factors are added, which are not available in the laboratory. After almost 10 years in the forest soils there still remains large quantities of the original product. Only 10-30 % of the wood ash products and 5 % of the lime product has been leached. In the laboratory study the leached amount was slightly larger, at the most 35 % for wood ash and 20 % for lime. Both studies indicate long time for weathering of the products in forest soils. Slower leaching rate from pellets of wood ash compared to leaching rate from crushed wood ash in the laboratory study is not verified by the field study. This indicates limited possibilities to control rates of leaching in the environment

The added value of business models

NARCIS (Netherlands)

Vliet, Harry van

An overview of innovations in a particular area, for example retail developments in the fashion sector (Van Vliet, 2014), and a subsequent discussion about the probability as to whether these innovations will realise a ‘breakthrough’, has to be supplemented with the question of what the added value

Opportunities of using bio-based materials for value-added composites

Science.gov (United States)

Zhiyong Cai

2010-01-01

Our forests are a naturally renewable resource that has been used as a principal source of bio-energy and building materials for centuries. The growth of world population and affluence has resulted in substantial increases in demand and in consumption for all raw materials. Resulting increases in demand for wood products provides a unique opportunity for developing new...

Colorimetry as grouping tool of eucalyptus clones wood

Directory of Open Access Journals (Sweden)

Márcio da Fonseca Martins

2015-12-01

Full Text Available The homogeneity of wood color in a batch to be marketed is of fundamental importance, as it will reflect in products quality resulting from its processing. In this context, this study aimed to evaluate, through colorimetric technique, the colorimetric parameters of Eucalyptus spp. wood from 25 clones and classify them into groups, according to color similarity degree. It was determined the lightness (L*, red-green color coordinate (a*, yellow-blue chromatic coordinate (b*, chromaticity (C* and ink angle (h. Radial and tangential faces and three positions in the radial direction were characterized using a colorimeter. Comparing to tangential planes, the results showed that radial plane presented larger values of L* and h in wood near the bark. Furthermore, it was observed higher values of L* in samples from intermediate radial positions. Finally, it was found that, as radial growth ocurred, developed timber showed less intense yellow shades. The definition of the wood color tones will be useful in timber market in the homogenization of their products, which will facilitate their marketing.

Reflecting on future research concerning the added value of FM

NARCIS (Netherlands)

Jensen, PA; van der Voordt, Theo; Coenen, C; Sarasoja, AL

2014-01-01

Purpose: To summarize recent research findings and reflections on The Added Value of Facilities Management and to outline perspectives for future research and development of the added value of FM.
Methodology - The article is based on reflections on contributions to the recently published book

Final Report: Development of Renewable Microbial Polyesters for Cost Effective and Energy- Efficient Wood-Plastic Composites

Energy Technology Data Exchange (ETDEWEB)

Thompson, David N.; Emerick, Robert W.; England, Alfred B.; Flanders, James P.; Loge, Frank J.; Wiedeman, Katherine A.; Wolcott, Michael P.

2010-03-31

In this project, we proposed to produce wood fiber reinforced thermoplastic composites (WFRTCs) using microbial thermoplastic polyesters in place of petroleum-derived plastic. WFRTCs are a rapidly growing product area, averaging a 38% growth rate since 1997. Their production is dependent on substantial quantities of petroleum based thermoplastics, increasing their overall energy costs by over 230% when compared to traditional Engineered Wood Products (EWP). Utilizing bio-based thermoplastics for these materials can reduce our dependence on foreign petroleum. We have demonstrated that biopolymers (polyhydroxyalkanoates, PHA) can be successfully produced from wood pulping waste streams and that viable wood fiber reinforced thermoplastic composite products can be produced from these materials. The results show that microbial polyester (PHB in this study) can be extruded together with wastewater-derived cell mass and wood flour into deck products having performance properties comparable to existing commercial HDPE/WF composite products. This study has thus proven the underlying concept that the microbial polyesters produced from waste effluents can be used to make cost-effective and energy-efficient wood-plastic composites. The cost of purified microbial polyesters is about 5-20 times that of HDPE depending on the cost of crude oil, due to high purification (40%), carbon substrate (40%) and sterilized fermentation (20%) costs for the PHB. Hence, the ability to produce competitive and functional composites with unpurified PHA-biomass mixtures from waste carbon sources in unsterile systems—without cell debris removal—is a significant step forward in producing competitive value-added structural composites from forest products residuals using a biorefinery approach. As demonstrated in the energy and waste analysis for the project, significant energy savings and waste reductions can also be realized using this approach. We recommend that the next step for development of

Wood pellets : is it a reliable, sustainable, green energy option?

International Nuclear Information System (INIS)

Swaan, J.

2006-01-01

The Wood Pellet Association of Canada was formerly called the BC Pellet Fuel Manufacturers Association, and was renamed and re-organized in January 2006. The association serves as an advocate for the wood pellet industry in addition to conducting research projects. This power point presentation presented an overview of the wood pellet industry in North America and Europe. Canada's 23 pellet plants currently produce just over 1,000,000 tons of wood pellets annually. Pellet producers in the United States produce approximately 800,000 tons annually for the residential bagged market. There are currently 240 pellet plants in Europe, and district heating is the largest growth market for wood pellets in Europe. British Columbia (BC) pellet producers will ship 450,000 tons to European power plants in 2005. Wood pellet specifications were presented, with details of calorific values, moisture and ash contents. An outline of wood pellet production processes was provided. New pellet plants currently under construction were reviewed. Domestic, North American and overseas exports were discussed, along with production estimates for BC for the next 5 years. A chart of world production and consumption of wood pellets between 2000 to 2010 was presented. North American wood pellet technologies were described. The impact of the pine beetle infestation in BC on the wood pellet industry was evaluated, and a worldwide wood pellet production growth forecast was presented. Issues concerning off-gassing, emissions, and torrifracation were also discussed. tabs., figs

Getting Value out of Value-Added: Report of a Workshop

Science.gov (United States)

Braun, Henry, Ed.; Chudowsky, Naomi, Ed.; Koenig, Judith, Ed.

2010-01-01

Value-added methods refer to efforts to estimate the relative contributions of specific teachers, schools, or programs to student test performance. In recent years, these methods have attracted considerable attention because of their potential applicability for educational accountability, teacher pay-for-performance systems, school and teacher…

Performance of Schizolobium amazonicum Wood in Bleached Kraft Pulp Production

Directory of Open Access Journals (Sweden)

Camila Sarto

2015-05-01

Full Text Available This study aimed to evaluate the characteristics of Schizolobium amazonicum wood, specifically its performance in bleached kraft pulp production and the characteristics of its pulp. Chips of Schizolobium amazonicum and Eucalyptus grandis x Eucalyptus urophylla (reference were used. The following parameters were evaluated in the wood: basic density, total extractives, total lignin, holocellulose, and fiber morphology. The pulping simulations were carried out in a laboratory digester, with parameters set to obtain pulp with kappa number 19 ± 0.5. Both pulps were bleached in a PFI mill and submitted to physical-mechanical tests. The results showed that S. amazonicum wood has low basic density and higher content of extractives when compared to E. grandis x E. urophylla wood. For pulping, S. amazonicum required higher alkali charge and H factor to achieve the same delignification level of E. grandis x E. urophylla, resulting in a lower yield, pulp with lower viscosity, and higher wood specific consumption. During bleaching, the brightness gain and final viscosity of S. amazonicum pulp were lower than E. grandis x E. urophylla pulp. Moreover, S. amazonicum pulp had worse physical-mechanical characteristics than E. grandis x E. urophylla.

Applying value stream mapping techniques to eliminate non-value-added waste for the procurement of endovascular stents.

Science.gov (United States)

Teichgräber, Ulf K; de Bucourt, Maximilian

2012-01-01

OJECTIVES: To eliminate non-value-adding (NVA) waste for the procurement of endovascular stents in interventional radiology services by applying value stream mapping (VSM). The Lean manufacturing technique was used to analyze the process of material and information flow currently required to direct endovascular stents from external suppliers to patients. Based on a decision point analysis for the procurement of stents in the hospital, a present state VSM was drawn. After assessment of the current status VSM and progressive elimination of unnecessary NVA waste, a future state VSM was drawn. The current state VSM demonstrated that out of 13 processes for the procurement of stents only 2 processes were value-adding. Out of the NVA processes 5 processes were unnecessary NVA activities, which could be eliminated. The decision point analysis demonstrated that the procurement of stents was mainly a forecast driven push system. The future state VSM applies a pull inventory control system to trigger the movement of a unit after withdrawal by using a consignment stock. VSM is a visualization tool for the supply chain and value stream, based on the Toyota Production System and greatly assists in successfully implementing a Lean system. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Adding value by FM: exploration of management practice in the Netherlands and Denmark

NARCIS (Netherlands)

van der Voordt, Theo; Jensen, PA

2014-01-01

The last decade shows a growing attention into the concept of added value of Facilities Management and Corporate Real Estate Management and how to attain and measure added value. A variety of different types of added value came to the fore such as user value, customer value, financial value,

Non_standard Wood

DEFF Research Database (Denmark)

Tamke, Martin

. Using parametric design tools and computer controlled production facilities Copenhagens Centre for IT and Architecture undertook a practice based research into performance based non-standard element design and mass customization techniques. In close cooperation with wood construction software......, but the integration of traditional wood craft techniques. The extensive use of self adjusting, load bearing wood-wood joints contributed to ease in production and assembly of a performance based architecture....

A Study on Value Added Tax for Business Enterprise Taxation - An Introduction

OpenAIRE

安部,知格

2002-01-01

In recent years，the argument whetter we should switch over the base of taxation for business enterprise from the income standard to other standards or not is rising. In these circumstances，as one of the other standards，the value-added tax has been taken up. The value-added tax appeared in Japan as the one which can be replaced income standard taxation for business enterprise by Shoup Mission in 1949. This paper considers the meaning of the value-added tax. Consequently，I think，the value-added...

Updating of U.S. Wood Product Life-Cycle Assessment Data for Environmental Product Declarations

Science.gov (United States)

Richard Bergman; Elaine Oneil; Maureen Puettmann; Ivan Eastin; Indroneil Ganguly

2014-01-01

The marketplace has an increasing desire for credible and transparent product eco-labels based on life-cycle assessment (LCA) data, especially involving international trade. Over the past several years, stakeholders in the U.S. wood products industry have developed many such “eco-labels” under the ISO standard of LCA-based environmental product declarations (EPDs). The...

Recent activities in flame retardancy of wood-plastic composites at the Forest Products Laboratory

Science.gov (United States)

Robert H. White; Nicole M. Stark; Nadir Ayrilmis

2011-01-01

For a variety of reasons, wood-plastic composite (WPC) products are widely available for some building applications. In applications such as outdoor decking, WPCs have gained a significant share of the market. As an option to improve the efficient use of wood fiber, the USDA Forest Service, Forest Products Laboratory (FPL), has an extensive research program on WPCs....

Exposure testing of fasteners in preservative treated wood: Gravimetric corrosion rates and corrosion product analyses

Energy Technology Data Exchange (ETDEWEB)

Zelinka, Samuel L., E-mail: szelinka@fs.fed.u [USDA Forest Products Laboratory, One Gifford Pinchot Drive, Madison, WI 53726 (United States); Sichel, Rebecca J. [College of Engineering, University of Wisconsin, Madison, WI 53706 (United States); Stone, Donald S. [Department of Materials Science and Engineering, College of Engineering, University of Wisconsin, Madison, WI 53706 (United States)

2010-12-15

Research highlights: {yields} The composition of the corrosion products was similar for the nail head and shank. {yields} Reduced copper was not detected on any of the fasteners. {yields} Measured corrosion rates were between 1 and 35 {mu}m year{sup -1}. - Abstract: Research was conducted to determine the corrosion rates of metals in preservative treated wood and also understand the mechanism of metal corrosion in treated wood. Steel and hot-dip galvanized steel fasteners were embedded in wood treated with one of six preservative treatments and exposed to 27 {sup o}C at 100% relative humidity for 1 year. The corrosion rate was determined gravimetrically and the corrosion products were analyzed with scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction. Although the accepted mechanism of corrosion in treated wood involves the reduction of cupric ions from the wood preservative, no reduced copper was found on the corrosion surfaces. The galvanized corrosion products contained sulfates, whereas the steel corrosion products consisted of iron oxides and hydroxides. The possible implications and limitations of this research on fasteners used in building applications are discussed.

Chapter 14: Evaluating the Leaching of Biocides from Preservative-Treated Wood Products

Science.gov (United States)

Stan T. Lebow

2014-01-01

Leaching of biocides is an important consideration in the long term durability and any potential for environmental impact of treated wood products. This chapter discusses factors affecting biocide leaching, as well as methods of evaluating rate and quantity of biocide released. The extent of leaching is a function of preservative formulation, treatment methods, wood...

The added value of Facility management in the educational environment

NARCIS (Netherlands)

Kok, H.B.; Mobach, M.; Omta, S.W.F.

2011-01-01

Purpose – The purpose of this paper is to define the added value of facility management (FM) in general and to develop a typology of facility services based on their added value in the educational environment. Design/methodology/approach – This paper is based on a literature review and first

BROMINATION OF 4-VINYLCYCLOHEXANE AND APPLYING THE RESULTING PRODUCT TO IMPROVE THE FLAME RETARDANT PROPERTIES OF WOOD

Directory of Open Access Journals (Sweden)

N. S. Nikulina

2014-01-01

Full Text Available Currently, the demand for timber is increasing. Wood and products on its basis are considered to be the most popular in the construction industry, furniture industry, as building materials and other However, along with the positive features of this material there are also negative factors, which include low resistance to biological degradation, high temperature, resistance. Wood and materials based on it are the most flammable, and fire safety is characterized by the velocity of propagation of fire on the wooden structure. He is able to destroy it in a matter of minutes. So the wooden house elements must be protected from fire. It was therefore necessary for the fire protection of wood. It is in the handling of wood with flame retardants. Basic fire fighting methods is the impregnation of wood antipyrene composition, painting fire paint and constructive ways - insulation of timber, non-combustible compositions which can resist the fire. In the work of brominated 4-vinylcyclohexane formed as a by-product in the petrochemical industry, in chloroform synthesized compound with bromine 62-64 % and the possibility of using this product to get antiferromag composition. It is established that the application for the protective treatment of wood synthesized flame retardant has shown that this product can be used for the protective treatment of natural wood to make it flame retardant properties. Use as antiperiodic compositions bromodomain based products 4-vinylcyclohexane allows to obtain images of wood first group of flame retardant efficiency.

Solid-wood production from temperate eucalypt plantations: a ...

African Journals Online (AJOL)

Since 1988, there has been a major focus in Tasmania on research for the management of temperate eucalypt plantations for solid wood. This coincided with the formal transfer of large areas of native forest that had previously been part of the production forest estate into reserves, a decision that triggered the establishment ...

Effect of wood type and thickness on acetification kinetics in traditional vinegar production

Directory of Open Access Journals (Sweden)

Maria-Jesús Torija

2009-04-01

Full Text Available Maria-Jesús Torija1, Estibaliz Mateo1, Carlos-Alfredo Vegas1, Carla Jara1, Angel González1, Montse Poblet1, Cristina Reguant1, Jóse-Manuel Guillamon2, Albert Mas11Biotecnología enológica. Departament de Bioquímica i Biotecnologia, Facultat d’enologia, Universitat Rovira i Virgili, Tarragona, Spain; 2Departamento de Biotecnología de los Alimentos, Instituto de Agroquímica y Tecnología de Alimentos (CSIC, Burjassot, València, SpainAbstract: Traditional vinegar production is a lengthy process which implies high operational risks and jeopardizes the organoleptic characteristics of the final product. In an effort to solve these problems without changing the traditional model, we modified the wood type and thickness of vinegar barrels. We acetified in triplicate in barrels made of acacia, cherry, chestnut, and oak and in three wood thicknesses (15, 20, and 25 mm in two different vinegar plants. The operating volume was set at 60 L. Reducing wood thickness improved neither maximum acetification velocity or the total length of the process, and in some cases even worsened them. The process took longer in oak barrels than in other types of wood barrel in one of the vinegar plants. Therefore, the choice of wood is a parameter to be considered in the wine vinegar production. Keywords: acacia, cherry, chestnut, oak, acetic acid bacteria

A technical and economic evaluation of wood conversion processes

Energy Technology Data Exchange (ETDEWEB)

Douglas, L J

1990-08-08

A technical and economic evaluation of the Iogen wood-to-ethanol bioconversion process was carried out using a computer simulation model based on an engineering analysis of the process. The model was used to run sensitivity analyses for the process and to estimate the parameters with significant economic impact and promise for future improvement to process economics. The most important parameters were then used in Monte Carlo simulations to estimate the potential for future improvements and to assess the commercial potential of the process. Finally, the process was subjected to second-law analysis, in which its thermodynamic efficiency was assessed in terms of lost work potential. The Iogen process is a highly optimized process using state-of-the-art enzymatic hydrolysis with steam explosion pretreatment; lactose sugar from cheese whey is used as the carbon source for enzyme production. The base case design would use 1000 tonnes/d of aspen wood and would produce 91 Ml/y of ethanol. Assuming no value for byproducts, the break-even price for ethanol would be 45-70{cents}/l, depending on the financing method employed. If byproduct credit is added for lignin and molasses, the required ethanol selling price would drop to 30-50{cents}/l. Forecasts for future technology improvements show that it is possible to construct scenarios where the ethanol price could be as low as 10-20{cents}/l including byproduct credits. Potential improvements to the process include reduced enzyme production cost; xylose fermentation to ethanol; lower-cost feedstock; and substitution of wood sugars for lactose. 48 refs., 39 figs., 21 tabs.

Added value: The differences that count

Directory of Open Access Journals (Sweden)

Dominique Bouchet

2012-08-01

Full Text Available Clinging to a simplistic conceptualization of the concept of added value might impair our capability to develop insights to what really matters today when companies seek to make differences within the global market. Today it is more necessary than ever to take into account the importance of language and culture as competitive factors.

Material use and production changes in the U.S. wood pallet and container industry: 1992 to 2006

Science.gov (United States)

R. J. Bush; P. A. Araman

2009-01-01

A series of five studies conducted by the Virginia Tech Department of Wood Science and Forest Products, in collaboration with the USDA - Forest Service (Blacksburg, Virginia), have tracked activity in the U.S. wood pallet and container industry between 1992 and 2006. The studies documented trends in wood use and pallet production with in the industry, both new...

Wood Products Other Building Materials Used in New Residential Construction in the United States

Science.gov (United States)

David B. McKeever; Joe Elling

2015-01-01

On average, new residential construction accounts for about one-third of all wood products consumed in the United States annually. During periods of robust housing activity, 45% or more of all wood products consumed are for new single-family and multifamily housing. This can fall to as low as 20% or less during times of economic recession. Unfortunately, 2012 was not...

Added value of FM – a critical review

DEFF Research Database (Denmark)

Jensen, Per Anker; van der Voordt, Theo

2015-01-01

The purpose of this paper is to provide a state of the art of how the topic “Added value of FM” has been treated recently in research and practice. The paper is based on research papers from EFMC 2013 and 2014. The paper provides an overview and a critical review of this research. A main focus...... is to examine to which degree there is a cumulative knowledge building in this field. The paper also summarises findings about value adding management in practice and reflects on implications for research and practice. The critical review shows that some of the papers have a strong foundation in former research...

The start of a Nordic focus on the added value of FM

DEFF Research Database (Denmark)

Jensen, Per Anker; Malmstrøm, Ole Emil

2012-01-01

. Findings: Different methods to demonstrate the added value of FM are presented and the analysis of the cases shows that a change in responsibility – both between core business and in-house FM and between in-house FM and providers - can be an important element in the possibility for FM to create added value....... On-going collaboration can also be an important leverage for adding value in FM. Practical implications: The findings can provide inspiration and methods for facilities managers to implement adding value initiatives and demonstrate their impact on the core business. Research limitations: The chapter...

Upgrading Wood-Based Industries: Harnessing the Social Network of Small-Scale Furniture Producers and Their Institutions

Directory of Open Access Journals (Sweden)

Melati ,

2011-05-01

Full Text Available Furniture is a major export commodity in Indonesia with a total value of USD 1.96 million in 2007.  Jepara District is one of the key location for wood furniture production with 15,271 furniture related business units employing 176,469 workers.  However, inefficiencies and power imbalances throughout the furniture value chain have resulted in overharvesting and uneven distribution of gains among the industry’s actors.  In contrast to price-setting international furniture retailers, small-scale producers enjoy the least value from their products.  In order to increase added value and competitiveness, small-scale furniture producers have made efforts to upgrade by harnessing their social network and institutions.  This paper describes small-scale furniture producers’ efforts to upgrade by utilising their social network and institutions in Jepara.  Data was collected through in-depth interviews with members of the small-scale furniture producers’ association.  The research provides insight into the nature of social networks and information flow and develops future scenarios to upgrade.  The scenarios will not only benefit the furniture industry in Jepara, but may also be adopted for similar industries throughout Indonesia and the world, and potentially improve many people’s economies and livelihoods.Keywords: wood-based industry, furniture, small-scale, social network, institution

Comparative economic value added on Southeast Asian banking industry

Directory of Open Access Journals (Sweden)

Lintang Dewanti

2017-03-01

Full Text Available This study analyses the bank's performance comparison across countries in some ASEAN members which are listed in the stock exchange, as well as to analyse the influence of Economic Value Added (EVA and some financial ratios on the company stock return. Analysis suggests some results. In Indonesia, Thailand and the Philippines, the movement of EVA follows the movement of Gross Domestic Product (GDP. This study also finds that Earning per Share (EPS, only in Singapore, and Return on Equity (ROE and Return on Assets (ROA, only in the Philippines, have an influence on stock return. Only in the Philippines where EVA together with ROA has an effect on stock return.

The Added Value of FM : Different Research Perspectives

NARCIS (Netherlands)

Jensen, P; van der Voordt, Theo; Coenen, C; von Felten, D; Lindholm, A

2010-01-01

Purpose: This paper aims to present and compare research perspectives and theoretical reflections from a variety of academic fields on the concept of Added Value of Facilities Management (FM).
Theory: The starting point is the so-called FM Value Map, which was presented in a paper by Jensen

Carbon sequestration in wood products: a method for attribution to multiple parties

International Nuclear Information System (INIS)

Tonn, Bruce; Marland, Gregg

2007-01-01

When forest is harvested some of the forest carbon ends up in wood products. If the forest is managed so that the standing stock of the forest remains constant over time, and the stock of wood products is increasing, then carbon dioxide is being removed from the atmosphere in net and this should be reflected in accounting for greenhouse gas emissions. We suggest that carbon sequestration in wood products requires cooperation of multiple parties; from the forest owner to the product manufacturer to the product user, and perhaps others. Credit for sequestering carbon away from the atmosphere could acknowledge the contributions of these multiple parties. Accounting under a cap-and-trade or tax system is not necessarily an inventory system, it is a system designed to motivate and/or reward an environmental objective. We describe a system of attribution whereby credits for carbon sequestration would be shared among multiple, contributing parties. It is hoped that the methodology outlined herein proves attractive enough to parties concerned to spur them to address the details of such a system. The system of incentives one would choose for limiting or controlling greenhouse gas emissions could be quite different, depending on how the attribution for emissions and sequestration is chosen

Recent progress in the development of solid catalysts for biomass conversion into high value-added chemicals

International Nuclear Information System (INIS)

Hara, Michikazu; Nakajima, Kiyotaka; Kamata, Keigo

2015-01-01

In recent decades, the substitution of non-renewable fossil resources by renewable biomass as a sustainable feedstock has been extensively investigated for the manufacture of high value-added products such as biofuels, commodity chemicals, and new bio-based materials such as bioplastics. Numerous solid catalyst systems for the effective conversion of biomass feedstocks into value-added chemicals and fuels have been developed. Solid catalysts are classified into four main groups with respect to their structures and substrate activation properties: (a) micro- and mesoporous materials, (b) metal oxides, (c) supported metal catalysts, and (d) sulfonated polymers. This review article focuses on the activation of substrates and/or reagents on the basis of groups (a)–(d), and the corresponding reaction mechanisms. In addition, recent progress in chemocatalytic processes for the production of five industrially important products (5-hydroxymethylfurfural, lactic acid, glyceraldehyde, 1,3-dihydroxyacetone, and furan-2,5-dicarboxylic acid) as bio-based plastic monomers and their intermediates is comprehensively summarized. (focus issue review)

Recent progress in the development of solid catalysts for biomass conversion into high value-added chemicals

Science.gov (United States)

Hara, Michikazu; Nakajima, Kiyotaka; Kamata, Keigo

2015-01-01

In recent decades, the substitution of non-renewable fossil resources by renewable biomass as a sustainable feedstock has been extensively investigated for the manufacture of high value-added products such as biofuels, commodity chemicals, and new bio-based materials such as bioplastics. Numerous solid catalyst systems for the effective conversion of biomass feedstocks into value-added chemicals and fuels have been developed. Solid catalysts are classified into four main groups with respect to their structures and substrate activation properties: (a) micro- and mesoporous materials, (b) metal oxides, (c) supported metal catalysts, and (d) sulfonated polymers. This review article focuses on the activation of substrates and/or reagents on the basis of groups (a)–(d), and the corresponding reaction mechanisms. In addition, recent progress in chemocatalytic processes for the production of five industrially important products (5-hydroxymethylfurfural, lactic acid, glyceraldehyde, 1,3-dihydroxyacetone, and furan-2,5-dicarboxylic acid) as bio-based plastic monomers and their intermediates is comprehensively summarized. PMID:27877800

The effect of adding urea, manganese and linoleic acid to wheat straw and wood chips on lignin degradation by fungi and subsequent

NARCIS (Netherlands)

Kuijk, van S.J.A.; Sonnenberg, A.S.M.; Baars, J.J.P.; Hendriks, W.H.; Cone, J.W.

2016-01-01

The aim of this study was optimizing Ceriporiopsis subvermispora and Lentinula edodes pre-treatment of wheat straw and wood chips by adding urea, manganese and linoleic acid. Optimization was defined as more lignin degradation and an increase in in vitro gas

Enhanced oil recovery chemicals from renewable wood resources

Energy Technology Data Exchange (ETDEWEB)

Grune, W.N.; Compere, A.L.; Griffith, W.L.; Crenshaw, J.M.

1979-04-01

Most of the wood pulp in the U.S. is produced by cooking, or digesting, wood chips in a chemical solution. These pulping processes have effluent streams which contain dissolved lignins, lignin breakdown products, and carbohydrates. There is a substantial economic incentive to use these materials as feedstocks for the production of high-valued micellar flood chemicals. The pulp and paper industries have practiced chemical recovery for almost a century. The largest chemical recycle processes are the internal recycle of inorganic salts for reuse in pulping. This is coupled with the use of waste organic compounds in the liquor as a fuel for directly-fired evaporation processes. Diversion of effluent and low valued streams for chemical recovery using fermentation, purification, or synthesis methods appears technically feasible in several cases. The use of new recovery processes could yield a variety of different wood-effluent based products. Some of the sugar acids in pulping liquors might be used as sequestering agents in reservoirs where there are large amounts of multivalent cations in flood brines. Fermentation production of high viscosity polymers, sequestering agents, and coagent alcohols appears worth further investigation. Tall oil acids and their derivatives can be used as surfactants in some reservoirs. Some waste constituents may adsorb preferentially on formations and thereby reduce loss of surfactants and other higher-valued chemicals.

2005 wood harvests in France - a definite recovery for timber and dendro-energy

International Nuclear Information System (INIS)

Cinotti, B.

2007-01-01

After dropping to 32.8 million m 3 in 2003, sales of wood harvests continue the recovery that began in 2004 and have reached 37.2 million m 3 (+ 5%) i.e., slightly more than the level reached prior to the 1999 storms (36.9 million m 3 ). Workable timber sales have increased by 5.9% up to 22.1 million m 3 but are nonetheless 4.5% below their 1999 level (23.2 million m 3 ). Industrial round-wood harvests have remained stable at 12.2 million m 3 (of which 11.8 are pulpwood). Sales of firewood have increased 23% (2.9 million m 3 ). Pre-tax roadside value of the entire wood harvest is estimated to be 1.64 billion Euro. French production of sawing timber is 9.7 million cubic metres with sawn softwood timber stagnating (+ 0.5%) and a drop in sawn hardwood timber (- 4.6%). The effects of the storms at the end of 1999 on the business cycle are no longer perceptible. Their consequences on the structure of harvests and of businesses are beginning to be understood. Average wood prices increased considerably in 2005 and 2006. These rosier market conditions for unprocessed timber could be an opportunity to continue with restructuring of the sector, in particular so as to further streamline harvests and narrow the wide gap between loggable and actually logged volumes, as well as to review the distribution of added value between the various players in the forest-based industries. (authors)

Factors influencing the role of Non-Wood Forest Products and Services

NARCIS (Netherlands)

Janse, G.; Ottitsch, A.

2005-01-01

In the light of social and economic developments, forest functions other than timber production have gained international importance and recognition. Resulting from this development, Non-Wood Forest Products and Services (NWFPS) are becoming more important, both for the general public as for forest

Fast pyrolysis of creosote treated wood ties in a fluidized bed reactor and analytical characterization of product fractions

International Nuclear Information System (INIS)

Jung, Su-Hwa; Koo, Won-Mo; Kim, Joo-Sik

2013-01-01

A fraction of creosote treated wood ties was pyrolyzed in a pyrolysis plant equipped with a fluidized bed reactor and char-separation system at different temperatures. Analyses of each pyrolysis product, especially the oil, were carried out using a variety of analytical tools. The maximum oil yield was obtained at 458 °C with a value of 69.3 wt%. Oils obtained were easily separated into two phases, a creosote-derived fraction (CDF) and a wood-derived fraction (WDF). Major compounds of the WDF were acetic acid, furfural and levoglucosan, while the CDF was mainly composed of polycyclic aromatic hydrocarbons (PAHs), such as 1-methylnaphthalene, biphenyl, acenaphthene, dibenzofuran, fluorene, phenanthrene, anthracene, fluoranthene and pyrene. HPLC analysis showed that the concentration of PAHs of the CDF obtained at 458 °C constituted about 22.5 wt% of the oil. - Highlights: • Creosote treated wood ties was stably pyrolyzed in a fluidized bed reactor. • Pyrolysis oil contained extremely low metal content due to the char removal system. • Bio-oil components was quantitatively analyzed by relative response factor. • Creosote-derived pyrolysis oil fraction was composed of PHAs and has a high caloric value (39 MJ/kg)

Sulphur highways : value-added solutions to create sulphur demand

Energy Technology Data Exchange (ETDEWEB)

Macedo, R.

2010-09-15

Producers generally view sulphur as a nuisance with essentially no benefit. In Alberta, a greater portion of sulphur production will shift from natural gas to the oilsands producing areas where there is limited infrastructure to move it out. Increased amounts of sour oil and gas production together with greater fuel desulphurization have also led to more sulphur being produced. In order to address the inevitable storage issue, Shell is considering value-added uses for the product, such as sulphur asphalt. The company developed Thiopave, a sulphur-based product for use in asphalt paving mixtures that can improve the mechanical performance of asphalt. The sulphur can be added to the asphalt mix as a solid pellet, which helps reduce the emission of sulphur vapour, odour and eye irritation. Twenty Thiopave projects are planned for the 2010 paving season in 9 U.S. states and 2 Canadian provinces. Sulphur Enhanced Asphalt Modifier (SEAM) was the first generation of Thiopave developed in 2003. SEAM replaces 20 to 25 percent by volume of the bitumen in asphalt mix. The properties allow Thiopave-enhanced roads to perform better than conventional roads in both consistently high temperature regions and climates with wide temperature variations. In 2007, an asphalt mix containing 40 percent by mass of Thiopave was used in a trial in Qatar. The Thiopave asphalt mix was compared with a conventional mix at temperatures ranging from 10 to 40 degrees C to determine the stiffness ratio. It was determined that Thiopave mixes containing high-penetration bitumen can be used to build temperature resistant roads that are stiffer in hot summer temperatures while improving the pavement's cold weather cracking performance. 1 ref., 4 figs.

Influence of alkaline hydrothermal pretreatment on shrub wood Tamarix ramosissima: Characteristics of degraded lignin

International Nuclear Information System (INIS)

Xiao, Ling-Ping; Bai, Yuan-Yuan; Shi, Zheng-Jun; Lu, Qiang; Sun, Run-Cang

2014-01-01

The objective of this work was to evaluate the influence of alkaline hydrothermal (AH) pretreatment on the physicochemical properties of the degraded lignins, attempt to upgrade the potential of lignin for value-added chemicals and fuel production. For this purpose, shrub wood Tamarix ramosissima lignin was fractionated using a two-stage process based on an AH pretreatment followed by an alkaline ethanol post-treatment. The recovered lignin fractions were investigated by comparison with milled wood lignin (MWL) in terms of fractionation yield, carbohydrate composition, gel permeation chromatography, Fourier transform infrared spectroscopy, 13 C and 2D heteronuclear single quantum correlation nuclear magnetic resonance, as well as pyrolysis-gas chromatography/mass spectrometry. The result showed that AH pretreatment led to the degradation of β-O-4 linkages and consequently the increased severity caused a release of more S-units lignin fractions with molecular weights between 1300 and 2500 g/mol in the liquid but higher molecular weights (3000–4400 g/mol) in the residues. Moreover, it was found that the lignin syringyl-to-guaiacyl (S/G) ratios from analytical pyrolysis slightly changed after AH pretreatment (S/G, 1.8–2.3) but higher than those of MWL (S/G, 1.7). Overall, the present study demonstrates that these lignins dissolved during AH pretreatment and those recovered from the solid residues isolated with alkaline ethanol post-treatment could be profitably exploited as feedstock in integrated forest biorefineries, rather than traditional use as low-value energy sources.- Highlights: • Alkaline hydrothermal pretreatment and alkaline ethanol post-treatment were proposed. • The influence of AH pretreatment on the lignin structural changes was characterized. • Aryl-O-ether linkages of lignin were extensively cleaved. • Lignin recovered from solid residue is a potential resource for the production of value-added chemicals

PENGUKURAN KINERJA PERUSAHAAN PT. HADJI KALLA DENGAN MENGGUNAKAN ANALISIS ECONOMIC VALUE ADDED

OpenAIRE

2013-01-01

Tujuan dari penelitian ini adalah mengetahui kinerja Economic Value Added (EVA) yang dicapai oleh perusahaan PT. Hadji Kalla, sedangkan metode analisis yang digunakan dalam penelitian ini adalah analisis perkembangan Economic Value Added (EVA), Net Operating Profit After Tax (NOPAT) dan The purpose of this study was to determine the performance of the Economic Value Added (EVA), which is achieved by the company PT. Hadji Kalla...

The Concept of added value of FM

NARCIS (Netherlands)

Jensen, PA; van der Voordt, Theo; Coenen, C; von Felten, D; Balslev-Nielsen, S; Sarasoja, AL; Riratanaphong, C.; Pfenninger, M; Jensen, PA; van der Voordt, DJM; Coenen, C

2012-01-01

Purpose: This chapter presents research perspectives and theoretical reflections on the concept of added value of FM from a variety of academic fields.
Methodology: A literature review of the most influential journals within the academic fields of Facilities Management (FM), Corporate Real

Geographical analyses of wood chips potentials, cost and supply for sustainable energy production in Denmark

DEFF Research Database (Denmark)

Möller, Bernd

2004-01-01

The paper presents a study which uses a practical application of rasterbased geographical information system to perform cost-supply analysis of wood chips resources for energy production.......The paper presents a study which uses a practical application of rasterbased geographical information system to perform cost-supply analysis of wood chips resources for energy production....

Added value of experts' knowledge to improve a quantitative microbial exposure assessment model--Application to aseptic-UHT food products.

Science.gov (United States)

Pujol, Laure; Johnson, Nicholas Brian; Magras, Catherine; Albert, Isabelle; Membré, Jeanne-Marie

2015-10-15

In a previous study, a quantitative microbial exposure assessment (QMEA) model applied to an aseptic-UHT food process was developed [Pujol, L., Albert, I., Magras, C., Johnson, N. B., Membré, J. M. Probabilistic exposure assessment model to estimate aseptic UHT product failure rate. 2015 International Journal of Food Microbiology. 192, 124-141]. It quantified Sterility Failure Rate (SFR) associated with Bacillus cereus and Geobacillus stearothermophilus per process module (nine modules in total from raw material reception to end-product storage). Previously, the probabilistic model inputs were set by experts (using knowledge and in-house data). However, only the variability dimension was taken into account. The model was then improved using expert elicitation knowledge in two ways. First, the model was refined by adding the uncertainty dimension to the probabilistic inputs, enabling to set a second order Monte Carlo analysis. The eight following inputs, and their impact on SFR, are presented in detail in this present study: D-value for each bacteria of interest (B. cereus and G. stearothermophilus) associated with the inactivation model for the UHT treatment step, i.e., two inputs; log reduction (decimal reduction) number associated with the inactivation model for the packaging sterilization step for each bacterium and each part of the packaging (product container and sealing component), i.e., four inputs; and bacterial spore air load of the aseptic tank and the filler cabinet rooms, i.e., two inputs. Second, the model was improved by leveraging expert knowledge to develop further the existing model. The proportion of bacteria in the product which settled on surface of pipes (between the UHT treatment and the aseptic tank on one hand, and between the aseptic tank and the filler cabinet on the other hand) leading to a possible biofilm formation for each bacterium, was better characterized. It was modeled as a function of the hygienic design level of the aseptic

A Planning Guide for Small and Medium Size Wood Products Companies

Science.gov (United States)

Jeff Howe; Stephen Bratkovich

2005-01-01

At the beginning of the 21st century, North American wood products companies are facing competitive pressure from numerous sources. Traditional products are being manufactured in new regions (e.g., China and the developing nations), and substitute products are being developed by competing industries (e.g., plastics and composites). The bottom line is strained by...

Testing painted wood : past practices at the Forest Products Laboratory and recommendations for future research

Science.gov (United States)

R. Sam Williams

2009-01-01

A brief history of paint research at the Forest Products Laboratory (FPL) in Madison, Wisconsin, sets the stage for a discussion of testing paint on wood and wood products. Tests include laboratory and outdoor tests, and I discuss them in terms of several degradation mechanisms (loss of gloss and fading, mildew growth, extractives bleed, and cracking, flaking, and...

From failure to value: economic valuation for a selected set of products and services from Mediterranean forests

Energy Technology Data Exchange (ETDEWEB)

Masiero, M.; Pettenella, D.; Secco, L.

2016-07-01

Aim of study: the paper estimates the economic value of a selected range of forest products and services, i.e. roundwood, non-wood forest products (NWFPs), and carbon-related services. Area of study: the research covers 21 Mediterranean countries, distinguished into four sub-regions. Material and methods: data have been gathered from official statistical sources (e.g. FAOSTAT), scientific literature and technical reports. Different estimation approaches based on market-price have been used for different products/services. Main results: the estimated value ranges between €10,512 and €11,158 million (M). Wood products represent more than 85% of the total value. Within them, industrial timber is the most relevant component (65%). Figures for NWFPs are likely to be underestimated because data are available only for some products and countries. When using alternative estimates for pine nuts, pine resin and cork, figures show a €36.8-572 M increase. In geographical terms, the economic value of Mediterranean forests is highly concentrated: North-West Mediterranean countries account for 70%, and nearly 90% is in just four countries (France, Spain, Turkey and Italy). Research highlights: enhancing the offer of Mediterranean forest products and increasing their role in the rural economy could help to reduce the costs of forest protection: a well-structured forest economy ensuring stable flows of incomes can provide a fundamental set of public non-market services and social values to both local people and the whole community. Understanding the true value of natural resources, then, is an essential step for promoting their protection and sustainable use. (Author)

Value Added Products from Renewable Biofuels

Energy Technology Data Exchange (ETDEWEB)

Blum, Paul [Univ. of Nebraska, Lincoln, NE (United States)

2014-07-31

Cellulosic ethanol is an emerging biofuel that will make strong contributions to American domestic energy needs. In the US midwest the standard method for pretreatment of biomass uses hot acid to deconstruct lignocellulose. While other methods work, they are not in common use. Therefore it is necessary to work within this context to achieve process improvements and reductions in biofuel cost. Technology underlying this process could supplement and even replace commodity enzymes with engineered microbes to convert biomass-derived lignocellulose feedstocks into biofuels and valueadded chemicals. The approach that was used here was based on consolidated bioprocessing. Thermoacidophilic microbes belonging to the Domain Archaea were evaluated and modfied to promote deconvolution and saccharification of lignocellulose. Biomass pretreatment (hot acid) was combined with fermentation using an extremely thermoacidophilic microbial platform. The identity and fate of released sugars was controlled using metabolic blocks combined with added biochemical traits where needed. LC/MS analysis supported through the newly established Nebraska Bioenergy Facility provided general support for bioenergy researchers at the University of Nebraska. The primary project strategy was to use microbes that naturally flourish in hot acid (thermoacidophiles) with conventional biomass pretreatment that uses hot acid. The specific objectives were: to screen thermoacidophilic taxa for the ability to deconvolute lignocellulose and depolymerize associated carbohydrates; evaluate and respond to formation of “inhibitors” that arose during incubation of lignocellulose under heated acidic conditions; identify and engineer “sugar flux channeling and catabolic blocks” that redirect metabolic pathways to maximize sugar concentrations; expand the hydrolytic capacity of extremely thermoacidophilic microbes through the addition of deconvolution traits; and establish the Nebraska Bioenergy Facility (NBF

An Overview of Natural Gas Conversion Technologies for Co-Production of Hydrogen and Value-Added Solid Carbon Products

Energy Technology Data Exchange (ETDEWEB)

Dagle, Robert A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Dagle, Vanessa [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Bearden, Mark D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Holladay, Jamelyn D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Krause, Theodore R. [Argonne National Lab. (ANL), Argonne, IL (United States); Ahmed, Shabbir [Argonne National Lab. (ANL), Argonne, IL (United States)

2017-11-16

This report was prepared in response to the U.S. Department of Energy Fuel Cell Technologies Office Congressional Appropriation language to support research on carbon-free production of hydrogen using new chemical processes that utilize natural gas to produce solid carbon and hydrogen. The U.S. produces 9-10 million tons of hydrogen annually with more than 95% of the hydrogen produced by steam-methane reforming (SMR) of natural gas. SMR is attractive because of its high hydrogen yield; but it also converts the carbon to carbon dioxide. Non-oxidative thermal decomposition of methane to carbon and hydrogen is an alternative to SMR and produces CO₂-free hydrogen. The produced carbon can be sold as a co-product, thus providing economic credit that reduces the delivered net cost of hydrogen. The combination of producing hydrogen with potentially valuable carbon byproducts has market value in that this allows greater flexibility to match the market prices of hydrogen and carbon. That is, the higher value product can subsidize the other in pricing decisions. In this report we highlight the relevant technologies reported in the literature—primarily thermochemical and plasma conversion processes—and recent research progress and commercial activities. Longstanding technical challenges include the high energetic requirements (e.g., high temperatures and/or electricity requirements) necessary for methane activation and, for some catalytic processes, the separation of solid carbon product from the spent catalyst. We assess current and new carbon product markets that could be served given technological advances, and we discuss technical barriers and potential areas of research to address these needs. We provide preliminary economic analysis for these processes and compare to other emerging (e.g., electrolysis) and conventional (e.g., SMR) processes for hydrogen production. The overarching conclusion of this study is that the cost of hydrogen can be potentially

Coaching Small Biotech Companies into Success: The Value-adding Function of VC

OpenAIRE

Terttu Luukkonen,; Mari Maunula,

2006-01-01

The paper reports an empirical study on the non-financial value-added provided by Venture Capital investors to their investee firms. This study will use a four-class grouping of the various non-financial value-adding capabilities provided by VC firms, namely, scouting, monitoring, signalling and value-adding services. The study examines biotechnology industry in Finland. Finland has a dual system with independent (partially ever-green) VC companies and public or semi-public VC organisations. ...

Towards an Integrated Value Adding Management Model for FM and CREM

NARCIS (Netherlands)

Jensen, Per Anker; van der Voordt, Theo; Kähkönen, Kalle; Keinänen, Marko

2016-01-01

Purpose: To present an integrated process model of adding value by Facilities Management (FM) and Corporate Real Estate Management (CREM) that is a generalisation of existing conceptual frameworks and aims to be a basis for management of added value in practice.
Background: The growing research

Value-Added Tax -- Can Schools Use It?

Science.gov (United States)

Salmon, Richard G.

1973-01-01

Defines the value-added tax and examines it in light of equity, economic effects, cost of administration, and stability and yield. Compares the tax with the property tax and suggests alternative ways in which States and the Federal Government may participate in the financing of education. (DN)

Water sorption in wood and modified wood at high values of relative humidity

DEFF Research Database (Denmark)

Thygesen, Lisbeth Garbrecht; Engelund, Emil Tang; Hoffmeyer, Preben

2010-01-01

additional results corroborate this conclusion: (1) calculation of the theoretical contribution of capillary condensation to the moisture content (MC) in wood based on idealized microstructural geometries by means of the Kelvin and Laplace equations resulted in very small contributions to the equilibrium...... moisture content (EMC), i.e., below 0.35% moisture at 99.9% RH. (2) The ratio between the EMC of acetylated and untreated samples did not show an increasing trend for increasing RH, as would have been the case if capillary condensation had taken place in both untreated and acetylated wood. (3) Low field......, and the pressure plate technique. The curve form for the untreated samples did not show an upward bend, except perhaps above 99.5% RH, indicating that – contrary to what has hitherto been assumed – capillary condensation does not play a significant role for water sorption in wood below fiber saturation. Three...

Influence of humic substances and wood decay products on the valency state of uranium

International Nuclear Information System (INIS)

Abraham, A.

2002-01-01

The purpose of the present study was to investigate the influence of dissolved natural substances on the oxidation state of iron and uranium. The ongoing remediation of uranium mining areas in Saxony and Thuringia involves flooding of extended pits, submerging and subjecting to microbial decay considerable amounts of pit timber in the process. This gives rise to the problem whether the reductive environment which develops as a result of wood decay in the pit water is capable of reducing the uranium (VI) and iron (III) contained in the flood water. Measurements of the valency state of uranium and iron following their interaction with natural decay products were performed by means of electrochemical, photometric and laser spectroscopic methods. This was followed by sorption experiments with a view to collecting phenomenological data on the binding behaviour of uranium species with respect to the rock bed of the Western Erz Hills and the sediments of the Elbe valley under different redox potential conditions. The study was concluded with redox potential calculations aimed at describing the state of pit waters as well as characterising analogous natural waters. The study was performed using humic acids for alkaline brown coal extract, high moor humic substances originating from natural microbial wood decay for wood decay products, and products from hydrothermal wood decomposition as well as lignin for a methanolic wood extract [de

Progress toward isolation of strains and genetically engineered strains of microalgae for production of biofuel and other value added chemicals: A review

International Nuclear Information System (INIS)

Ghosh, Ashmita; Khanra, Saumyakanti; Mondal, Madhumanti; Halder, Gopinath; Tiwari, O.N.; Saini, Supreet; Bhowmick, Tridib Kumar; Gayen, Kalyan

2016-01-01

Highlights: • Sample collection, isolation and identification to obtain a pure microalgal species. • Isolation of microalgal strains worldwide based on continent and habitat. • Genetic engineering tools for enhanced production of biodiesel and value added chemicals. • Cultivation systems for genetically modified strain. - Abstract: Microalgae and cyanobacteria are promising sources of biodiesel because of their high oil content (∼10 fold higher) and shorter cultivation time (∼4 fold lesser) than conventional oil producing territorial plants (e.g., soybean, corn and jatropha). These organisms also provide source of several valuable natural chemicals including pigments, food supplements like eicosapentanoic acid [EPA], decosahexaenoic acid [DHA] and vitamins. In addition, many cellular components of these organisms are associated with therapeutic properties like antioxidant, anti-inflammatory, immunostimulating, and antiviral. Isolation and identification of high-yielding strains with the faster growth rate is the key for successful implementation of algal biodiesel (or other products) at a commercial level. A number of research groups in Europe, America, and Australia are thus extensively involved in exploration of novel microalgal strain. Further, genetic engineering provides a tool to engineer the native strain resulting in transgenic strain with higher yields. Despite these efforts, no consensus has yet been reached so far in zeroing on the best microalgal strain for sustainable production of biofuel at reasonable cost. The search for novel microalgal strain and transgenesis of microalgae, are continuing side by side with the hope of commercial scale production of microalgae biofuel in near future. However, no consolidated review report exists which guides to isolate and identify a uncontaminated microalgal strain along with their transgenesis. The present review is focused on: (i) key factors for sample collection, isolation, and identification to

English Value-Added Measures: Examining the Limitations of School Performance Measurement

Science.gov (United States)

Perry, Thomas

2016-01-01

Value-added "Progress" measures are to be introduced for all English schools in 2016 as "headline" measures of school performance. This move comes despite research highlighting high levels of instability in value-added measures and concerns about the omission of contextual variables in the planned measure. This article studies…

Wood plastic combination

International Nuclear Information System (INIS)

Cunanan, S.A.; Bonoan, L.S.; Verceluz, F.P.; Azucena, E.A.

1976-03-01

The purpose of this study is to improve the physical and mechaniproperties of local inferior quality wood species by radiation-induced graft polymerization with plastic monomers. The process involves the following: 1) Preparation of sample; 2) Impregnation of sample with the monomers; 3) Irradiation of the impregnated sample with the use of 20,000 curie Co-60 as gamma-source; 4) Drying of irradiated sample to remove the unpolymerized monomer. Experimentation on different wood species were undertaken and the results given. From the results obtained, it can be concluded that the monomers systems MMA, MMA-USP, and styrene-USP are suitable for graft polymerization with the wood species almon, apitong, bagtikan, mayapis, red lauan, and tanguile. This is shown by their maximum conversion value which range from 86% to 96% with the optimum dose range of 1 to 2 Mrads. However, in the application of WPC process, properties that are required in a given wood product must be considered, thus aid in the selection of the monomer system to be used with a particular wood species. Some promising applications of WPC is in the manufacture of picker sticks, shuttles, and bobbins for the textile industry. However, there is a need for a pilot plant scale study so that an economic assessment of the commercial feasibility of this process can be made

Bioconversion of Sugarcane Vinasse into High-Added Value Products and Energy

Science.gov (United States)

Machado, Antonio Carlos de Oliveira

2017-01-01

Vinasse, a residue from bioethanol production containing high organic matter concentration, was used as substrate in submerged fermentation of Pseudomonas aeruginosa PA1 for biosurfactant production. About 2.7 g/L of rhamnolipids was obtained, with surface tension of 29.2 mN/m and critical micelle concentration of 80.3 mg/L. After separation of rhamnolipid and biomass, residual fermentation media were submitted to anaerobic biodegradation in mesophilic conditions. The residual medium derived from fermentation with vinasse diluted to 1 : 1, without addition of nitrogen, C : N 21, and for 168 h, led to 63.2% chemical oxygen demand (COD) removal and 97.6 mL CH4/g CODremoved. Compared to results obtained with fresh vinasse (73.7% COD removal and 112.4 mL CH4/g CODremoved), it could be concluded that both processes can be integrated in order to add value to the residue and obtain energy, reducing production costs and at the same time environmental impacts related to vinasse disposal. PMID:29250551

Production of wood derived fuels. Review of research projects; Puupolttoaineiden tuotantotekniikka. Tutkimusalueen katsaus

Energy Technology Data Exchange (ETDEWEB)

Korpilahti, A [Metsaeteho Oy, Helsinki (Finland)

1997-12-01

The research and development work was very active on the area of wood derived fuels during the past year 1996. Totally some 40 projects were going on, and till the end of the year about 15 projects were completed. The projects broadly covered the research area focusing from material flows, productivity studies, basic wood properties to several case studies. When new production methods and machinery was introduced earlier by demonstration projects, now they were investigated by follow up projects. The economical and quality results of logging residue harvesting and comminution seem quite satisfactory, but integrated methods and production chains still need research and development. (orig.)

Assessing radiation doses to the public from radionuclides in timber and wood products

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-10-01

In the event of a nuclear accident involving the release of radionuclides to the biosphere the radioactive contamination of forests can become a significant potential source of public radiation exposure. Two of these accidents - the Kyshtim accident, Urals, USSR (now Russian Federation) in 1957 and the Chernobyl accident, USSR (now Ukraine), in 1986 - resulted in significant contamination of thousands of square kilometres of forested areas with mixtures of radionuclides including long lived fission products such as {sup 137}Cs and {sup 90}Sr. Measurements and modelling of forest ecosystems after both accidents have shown that, following initial contamination, the activity concentration of long lived radionuclides in wood gradually increases over one to two decades and then slowly decreases in the subsequent period. The longevity of the contamination is due to the slow migration and persistent bioavailability of radionuclides in the forest soil profile, which results in long term transfer into wood through the root system of the trees. Another source of contamination is from global radioactive fallout after nuclear weapons tests, but the level of contamination is much lower than that from, for example, the Chernobyl accident. For instance, the level of {sup 137}Cs in wood in Sweden is about 2-5 Bq kg{sup -1} from global fallout. Global values are very similar to the Swedish levels. In contrast, the level of {sup 137}Cs in Swedish wood due to Chernobyl is around 50 Bq kg{sup -1}. Levels in wood from some contaminated areas located in countries of the Former Soviet Union (FSU) are about one to two orders of magnitude higher than this. The data on {sup 137}Cs soil contamination within European territories, originating mainly from the Chernobyl accident, illustrate the scale of the problem. For comparison, residual {sup 137}Cs soil deposition in Europe from global radioactive fallout was in the range 1-4 kBq m{sup -2}. There is concern in several countries about the

A Documentation of Some Traditional Aspects of Wood Consumption in Anaocha, Nigeria

Directory of Open Access Journals (Sweden)

Emeka E. Okonkwo

2016-05-01

Full Text Available The usefulness of wood to mankind varies from place to place, community to community, state to state, and nation to nation. Wood is a natural product, which is one of the components of biodiversity and a bio-product that serves numerous purposes to mankind. Such multifunctional purposes include those of sociopolitical, economic, religious, and cultural aspects of man. This article examines some traditional aspects of wood consumption in Anaocha Local Government Area of Anambra State, Nigeria, with a view to ascertaining the uses to which the people put wood as a by-product of the trees around them. In-depth interview, on-the-site observation, and focused group discussion were used to elicit information from knowledgeable elders, artisans, and wood vendors in different towns that make up the local government area. This research brings to limelight aspects of wood consumption in Anaocha and lends credence to the belief that wood is still the major source of revenue and energy in rural areas, probably because it is a free gift of nature. The research findings show that modernization has not completely eroded the value of wood in the study area.

The added value of advisory services in SME mergers and acquisitions

NARCIS (Netherlands)

Lex van Teeffelen

2013-01-01

The objective of this study is to shed light on the added value of the services of five disciplines in M&A advisory in the SME domain: accountants, bankers, business brokers, fiscalists and lawyers. Theory is inconclusive in the added value of advisory services and research on the subject is hardly

Management of Tax Payments Under the Definitive Value Added Tax Regime

Directory of Open Access Journals (Sweden)

Jurušs Māris

2018-04-01

Full Text Available There is a large value added tax fraud in the European Union. The current value added tax system is universal as tax is applied to all parties involved in the chain transactions, thus creating a risk of tax losses if one of the parties involved in the chain transaction does not pay tax in good faith. There is the action plan to introduce the definitive value added tax to prevent tax fraud in intra-community transactions. However, in order to ensure normal value added tax administration in all member states, a number of measures are needed to be done. It is necessary to develop a mutual settlement mechanism in cases of intra-community transactions. The aim of this research is to develop a possible solution for the management of tax payments under the definitive value added tax regime. The results of the research show that to manage tax payments, several payment management systems can be used. However, as a solution, a special clearing system could be introduced. Quantitative research methods such as statistical methods were used in order to analyze the situation of tax fraud in EU and its main causes, as well as mathematical modeling methods to analyze the definitive VAT system and to calculate the balance between countries in an example for clearing mechanism.

How to Use Value-Added Measures Right

Science.gov (United States)

Di Carlo, Matthew

2012-01-01

Value-added models are a specific type of "growth model," a diverse group of statistical techniques to isolate a teacher's impact on his or her students' testing progress while controlling for other measurable factors, such as student and school characteristics, that are outside that teacher's control. Opponents, including many teachers, argue…

Commercialization and marketing of non-wood forest products in Central Serbia

Directory of Open Access Journals (Sweden)

Keča Ljiljana

2013-01-01

Full Text Available The phenomenon of return to nature and its original values is increasingly common worldwide in accordance with the principles of sustainable development. In this context, it is particularly important to pay attention to organic products, as well as the increased demand for healthy food. In these circumstances non-wood forest products (NWFPs emerge as forestry products that meet the criteria of organic farming and as such are placed on the market. The aim of this research was to acquire knowledge about the behavior of the marketing mix elements of NWFPs in Central Serbia in the period from 2007 to 2011. The purpose of this paper was to point to the opportunities for the development of enterprises, and the overall potential of Serbia for the development of companies engaged in purchasing, processing and placement of NWFPs. The research object were the quantities of products purchased and placed on both domestic and foreign markets, the types of promotional activities, the prices of final products and distribution of the products among the enterprises engaged in purchasing, processing and placement of NWFPs in Central Serbia. [Projekat Ministarstva nauke Republike Srbije, br. 37008: Održivo gazdovanje ukupnim potencijalima šuma u Republici Srbiji

Trade in value added in the West Pacific: An input-output analysis

OpenAIRE

Nakamura, Yoichi

2015-01-01

The evolution of trade between the four regions in the West Pacific in both gross and value added terms is analyzed using international input-output tables. It is found that value added exports of computers and electronic equipment of the Asian economies are very limited in comparison with their gross exports, and that the largest shares of value added exports were accounted for by the services sectors in every region, particularly so in Japan and the US. Surpluses and deficits in bilateral t...

Current research in Spain on walnut for wood production

Science.gov (United States)

Neus Alet& #224; Neus NO-VALUE

2004-01-01

The Department of Mediterranean Trees at the Institut de Recerca i Tecnologia Agroalimentaries (IRTA) in Spain initiated a research program in 1993 to examine the variability among walnut species for wood production and to establish orchards with improved selections. The main objective of the programme is to obtain superior Persian walnut (Juglans regia...

Added values of photovoltaic power systems

International Nuclear Information System (INIS)

2001-03-01

The structure, ownership and operation of electricity systems around the world are changing in response to industry restructuring, the availability of new technologies and increasing environmental awareness. At the same time, many countries have yet to provide basic energy services for their populations, particularly in areas not served by the electricity grid. Large-scale, central power generation and distribution which characterized the electricity industry for much of the 20 th century is being challenged by new technologies, which are cleaner, faster to deploy and better matched to local requirements. Higher values are being placed on ancillary services, such as power system reliability and voltage stability, so that a simple comparison of energy cost is no longer appropriate as a measure of competitiveness. Solar photovoltaic electricity is unique amongst the new energy sources for the wide range of energy and non-energy benefits which can be provided, while the use of photovoltaic power systems as an integral part of a building provides the greatest opportunity for exploiting non-energy benefits and for adding value to the photovoltaic power system. This report documents the potential added values or non-energy benefits photovoltaic power systems can provide, the current state of market development and the key barriers faced by renewable energy technologies generally and photovoltaic power systems in particular. Means by which non-energy benefits may be used to overcome barriers to the use of photovoltaic power systems are then discussed, with specific attention to the use of building integrated photovoltaics. (author)

Added values of photovoltaic power systems

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-15

The structure, ownership and operation of electricity systems around the world are changing in response to industry restructuring, the availability of new technologies and increasing environmental awareness. At the same time, many countries have yet to provide basic energy services for their populations, particularly in areas not served by the electricity grid. Large-scale, central power generation and distribution which characterized the electricity industry for much of the 20{sup th} century is being challenged by new technologies, which are cleaner, faster to deploy and better matched to local requirements. Higher values are being placed on ancillary services, such as power system reliability and voltage stability, so that a simple comparison of energy cost is no longer appropriate as a measure of competitiveness. Solar photovoltaic electricity is unique amongst the new energy sources for the wide range of energy and non-energy benefits which can be provided, while the use of photovoltaic power systems as an integral part of a building provides the greatest opportunity for exploiting non-energy benefits and for adding value to the photovoltaic power system. This report documents the potential added values or non-energy benefits photovoltaic power systems can provide, the current state of market development and the key barriers faced by renewable energy technologies generally and photovoltaic power systems in particular. Means by which non-energy benefits may be used to overcome barriers to the use of photovoltaic power systems are then discussed, with specific attention to the use of building integrated photovoltaics. (author)

Certification of forests and wood products in Serbia in the context of new European union legislations: Current situation, problems and challenges

Directory of Open Access Journals (Sweden)

Vasiljević Aleksandar

2011-01-01

Full Text Available The paper presents research results of the current situation in the area of certification of forests and wood products in Serbia in the context of new European Union legislation referring to the placement of wood and wood products on this market. The objective of the research was to observe the situation, phases which Serbia implemented in the process of forest and wood products certification until now, as well as the problems and challenges the companies in this process face. Based on research results, future development of the market of certified wood products in Serbia was assessed and the proposal of measures which should be realized in order for Serbia to become a country whose companies will be ready for the moment when provisions and measures of the new EU legislation become effective was given. The selection of the abovementioned objective was conditioned by the fact that from January 1st, 2013 new legislation takes effect, with significantly stricter terms for the placement of wood and wood products from other countries on this market. One of the conditions which will have to be fulfilled by the companies wishing to export their products on this market refers to proving their origin. Since the EU is the most significant market for wood products exported from Serbia, fulfillment of the stated and other terms from the new EU legislation is of great importance to Serbian companies. Until the beginning of September 2010, only 387,000 ha were certified, namely 17.2% of the total area under forests. In the same period, only 33 wood processing companies in Serbia possessed CoC certificates for their products. Such a small number of companies possessing certificates for their wood products compared to competitive neighboring countries can represent a serious limitation in achieving their satisfactory competitiveness on the EU market in the following period.

Visible-light activate Ag/WO3 films based on wood with enhanced negative oxygen ions production properties

Science.gov (United States)

Gao, Likun; Gan, Wentao; Cao, Guoliang; Zhan, Xianxu; Qiang, Tiangang; Li, Jian

2017-12-01

The Ag/WO3-wood was fabricated through a hydrothermal method and a silver mirror reaction. The system of visible-light activate Ag/WO3-wood was used to produce negative oxygen ions, and the effect of Ag nanoparticles on negative oxygen ions production was investigated. From the results of negative oxygen ions production tests, it can be observed that the sample doped with Ag nanoparticles, the concentration of negative oxygen ions is up to 1660 ions/cm3 after 60 min visible light irradiation. Moreover, for the Ag/WO3-wood, even after 60 min without irradiation, the concentration of negative oxygen ions could keep more than 1000 ions/cm3, which is up to the standard of the fresh air. Moreover, due to the porous structure of wood, the wood acted as substrate could promote the nucleation of nanoparticles, prevent the agglomeration of the particles, and thus lead the improvement of photocatalytic properties. And such wood-based functional materials with the property of negative oxygen ions production could be one of the most promising materials in the application of indoor decoration materials, which would meet people's pursuit of healthy, environment-friendly life.

Fruit production and branching density affect shoot and whole-tree wood to leaf biomass ratio in olive.

Science.gov (United States)

Rosati, Adolfo; Paoletti, Andrea; Al Hariri, Raeed; Famiani, Franco

2018-02-14

The amount of shoot stem (i.e., woody part of the shoot) dry matter per unit shoot leaf dry matter (i.e., the shoot wood to leaf biomass ratio) has been reported to be lower in short shoots than in long ones, and this is related to the greater and earlier ability of short shoots to export carbon. This is important in fruit trees, since the greater and earlier carbon export ability of shoots with a lower wood to leaf biomass ratio improves fruit production. This ratio may vary with cultivars, training systems or plant age, but no study has previously investigated the possible effect of fruit production. In this study on two olive cultivars (i.e., Arbequina, with low growth rate, and Frantoio, with high growth rate) subject to different fruit production treatments, we found that at increasing fruit production, shoot length and shoot wood to leaf biomass ratio were proportionally reduced in the new shoots growing at the same time as the fruit. Specifically, fruit production proportionally reduced total new-shoot biomass, length, leaf area and average shoot length. With decreasing shoot length, shoot diameter, stem mass, internode length, individual leaf area and shoot wood to leaf biomass ratio also decreased. This may be viewed as a plant strategy to better support fruit growth in the current year, given the greater and earlier ability of short shoots to export carbon. Moreover, at the whole-tree level, the percentage of total tree biomass production invested in leaves was closely correlated with branching density, which differed significantly across cultivars. By branching more, Arbequina concentrates more shoots (thus leaves) per unit of wood (trunk, branches and root) mass, decreasing wood to leaf biomass ratio at the whole-tree level. Therefore, while, at the shoot level, shoot length determines shoot wood to leaf biomass ratio, at the canopy level branching density is also an important determinant of whole-tree wood to leaf biomass ratio. Whole-tree wood to leaf

Wood Volume Production and Use of 10 Woody Species in Semiarid Zones of Northeastern Mexico

Directory of Open Access Journals (Sweden)

Rahim Foroughbakhch

2012-01-01

Full Text Available A research strategy was established to analyze the structure of timber trees in terms of forest productivity (volume and wood density of 10 species. The native species Acacia farnesiana, Acacia schaffneri, Bumelia celastrina, Cercidium macrun, Condalia hookeri, Ebenopsis ebano, Helietta parvifolia, and Prosopis laevigata and the exotic species Eucalyptus camaldulensis and Leucaena leucocephala were chosen due to their ecological and economic importance to the rural villages of northeastern Mexico. Measurements of different growth parameters and volume of trees were evaluated. The introduced species E. camaldulensis and L. leucocephala showed the best performance in wood volume production per tree and per hectare when compared to the native species. Likewise, among the native species, E. ebano, P. laevigata, C. hookeri, and A. farnesiana tended to show better characteristics in terms of wood volume production in comparison to H. parvifolia, A. schaffneri, C. macrum, and B. celastrina. Results showed a high diversity on the properties studied. The high biomass produced by most of the species considered in this study revealed their great energetic potential when used as wood and firewood or vegetal charcoal.

Potential of synthesis gas production from rubber wood chip gasification in a bubbling fluidised bed gasifier

International Nuclear Information System (INIS)

Kaewluan, Sommas; Pipatmanomai, Suneerat

2011-01-01

Experiments of rubber wood chip gasification were carried out in a 100-kW th bubbling fluidised bed gasifier to investigate the effect of air to fuel ratio (represented as equivalence ratio - ER) on the yield and properties of synthesis gas. For all experiments, the flow rate of ambient air was fixed, while the feed rate of rubber wood chip was adjusted to vary ER in the range of 0.32-0.43. Increasing ER continuously raised the bed temperature, which resulted in higher synthesis gas yield and lower yield of ash and tar. However, higher ER generally gave synthesis gas of lower heating value, partly due to the dilution of N 2 . Considering the energy efficiency of the process, the optimum operation was achieved at ER = 0.38, which yielded 2.33 Nm 3 of synthesis gas per kg of dry biomass at the heating value of 4.94 MJ/Nm 3 . The calculated carbon conversion efficiency and gasification efficiency were 97.3% and 80.2%, respectively. The mass and energy balance of the gasification process showed that the mass and energy distribution was significantly affected by ER and that the energy losses accounted for ∼25% of the total output energy. The economical assessment of synthesis gas utilisation for heat and electricity production based on a 1-MW th bubbling fluidised bed gasifier and the operational data resulting from the rubber wood chip gasification experiments in this study clearly demonstrated the attractiveness of replacing heavy fuel oil and natural gas by the synthesis gas for heat applications in terms of 70% and 50% annual saving of fuel cost, respectively. However, the case of electricity production does not seem a preferable option due to its current technical and non-technical barriers.

Developing and commercializing sustainable new wood products : a process for identifying viable products.

Science.gov (United States)

Gordon A. Enk; Stuart L. Hart

2003-01-01

A process was designed to evaluate the sustainability and potential marketability of USDA Forest Service patented technologies. The process was designed and tested jointly by the University of North Carolina, the University of Michigan, Partners for Strategic Change, and the USDA Forest Service. Two technologies were evaluated: a fiber-based product and a wood fiber/...

Radiocarbon measurements of tree-ring samples from Japanese woods

International Nuclear Information System (INIS)

Ozaki, Hiromasa; Sakamoto, Minoru; Imamura, Mineo; Mitsutani, Takumi

2008-01-01

Since radiocarbon age is a model age based on constancy of atmospheric radiocarbon concentration and a provisional value of 5568 years for the 14 C half-life, calibration to calendar age is required for practical dating. The dataset, called IntCal, used for the calibration has been constructed by international consortium. Most parts of the IntCal have been based on the measurement of radiocarbon in dendrochronologically dated tree-ring samples from woods in Europe and North America. Regional offsets, which are designed as differences of local atmospheric radiocarbon from IntCal, have been pointed out based on recent radiocarbon measurements for tree-ring samples from a few regions. We have also measured radiocarbon of tree-ring samples from Japanese woods in order to investigate regional offsets in Japan. In this study, radiocarbon measurements for tree-ring samples from three different Japanese woods at around AD500 were carried out. Consequently, differences from IntCal04 at around AD500 were confirmed, although no systematic offset are found. However, the results obtained in this study agree with the raw data used for construction of IntCal04. This could pose a question to calculation method of IntCal04. (author)

Integrated production method for wood fuel and pulp wood in Northern Finland; Polttojakeen hankinta puun yhdistelmaekorjuussa ja integroitu energiapuun tuotantomenetelmae Pohjois-Suomessa

Energy Technology Data Exchange (ETDEWEB)

Hooli, A [Hooli Oy, Kemi (Finland); Kuitto, P J [VTT Energy, Jyvaeskylae (Finland); Ranta, T [Finntech Ltd. Oy, Jyvaeskylae (Finland)

1997-12-31

Chip production company Hooli Ltd. has built an innovative mobile chain-flail delimbing-debarking-unit which includes also a hammer crusher for wood fuel. This integrated production method for wood fuel and pulp wood based on that unit has been planned especially for the circumstances where the power or heating plants are near and the pulp mills more remote from the wood processing sites. The trees are felt into bunches and transported as whole trees or tree-sections to the roadside. The Hooli-unit delimbs and debarks the trees using multi-tree processing. The optimal bark content of Scot pine bolts after processing is under 1 %. All green branches, stops and bark are directly crushed into wood fuel in the same unit. Fuel chips are carried to the nearest power plant. The debarked bolts are transported to the pulpmills in the form of roundwood or pulpchips, thus giving better economy for the whole method. Based on first field experiments in 1995 this method has operated well. However, there are still development work ahead: e.g. good debarking quality of birch and spruce in the winter conditions. To attain the targets of the project looks promising. The project is carried out as joint project between Hooli Ltd, Finntech Ltd. Oy, the Finnish Forest Research Institute, Veitsiluoto Ltd and VTT Energy. The chain-flail delimbing-debarking-crushing unit was built at Tervolan Konepaja Ky

Integrated production method for wood fuel and pulp wood in Northern Finland; Polttojakeen hankinta puun yhdistelmaekorjuussa ja integroitu energiapuun tuotantomenetelmae Pohjois-Suomessa

Energy Technology Data Exchange (ETDEWEB)

Hooli, A. [Hooli Oy, Kemi (Finland); Kuitto, P.J. [VTT Energy, Jyvaeskylae (Finland); Ranta, T. [Finntech Ltd. Oy, Jyvaeskylae (Finland)

1996-12-31

Chip production company Hooli Ltd. has built an innovative mobile chain-flail delimbing-debarking-unit which includes also a hammer crusher for wood fuel. This integrated production method for wood fuel and pulp wood based on that unit has been planned especially for the circumstances where the power or heating plants are near and the pulp mills more remote from the wood processing sites. The trees are felt into bunches and transported as whole trees or tree-sections to the roadside. The Hooli-unit delimbs and debarks the trees using multi-tree processing. The optimal bark content of Scot pine bolts after processing is under 1 %. All green branches, stops and bark are directly crushed into wood fuel in the same unit. Fuel chips are carried to the nearest power plant. The debarked bolts are transported to the pulpmills in the form of roundwood or pulpchips, thus giving better economy for the whole method. Based on first field experiments in 1995 this method has operated well. However, there are still development work ahead: e.g. good debarking quality of birch and spruce in the winter conditions. To attain the targets of the project looks promising. The project is carried out as joint project between Hooli Ltd, Finntech Ltd. Oy, the Finnish Forest Research Institute, Veitsiluoto Ltd and VTT Energy. The chain-flail delimbing-debarking-crushing unit was built at Tervolan Konepaja Ky

Wood products in the waste stream: Characterization and combustion emissions. Volume 1. Final report

International Nuclear Information System (INIS)

1992-11-01

Waste wood is wood separated from the solid-waste stream and processed into a uniform-sized product that is reused for other purposes such as fuel. As an alternative to the combustion of fossil fuels, it has raised concerns that if it is 'contaminated' with paints, resins, preservatives, etc., unacceptable environmental impacts may be generated during combustion. Given the difficulty of separating contaminated materials from waste wood and the large energy potential existing in the resource, it is important to identify possible problems associated with contaminated waste wood combustion. The study describes research about technical, public policy, and regulatory issues that affect the processing and combustion of waste wood for fuel. The project's purpose was to provide environmental regulators, project developers, and others with data to make informed decisions on the use of waste wood materials as a combustion resource. Potential environmental problems and solutions were identified. A specific project result was the identification of combustion system operation parameters and air pollution control technologies that can minimize emissions of identified air and solid waste contaminants from combustion of wood waste

EFFECT OF ARTIFICIAL WEATHERING ON WOOD LAMINATES COLOR TREATED WITH TWO FINISHING PRODUCTS

Directory of Open Access Journals (Sweden)

Thais Jacob Mendes

2016-03-01

Full Text Available Weathering is one of the main reasons for the degradation of wood, especially its color. The application of finishes minimizes these effects. This study aimed to monitor the effect of artificial weathering on wood veneer of the species cumaru (Dipteryx odorata and pau marfim (Balfourodendron riedelianum with two finishes, the marine varnish and Cetol, with monitoring using a spectrophotometer. The samples were subjected to cycles of exposure to weathering for 20, 40, 52, 76, 124, 226, 430, 838 and 960 hours. The colorimetric parameters (L*, a*, b*, C and h* were measured before treatment, after application of the products and during the weathering time intervals. The application of finishes darkened veneer of cumaru wood and pau marfim in nature. However, in higher weathering times, both species returned to a lighter color, and even became lighter than the natural wood. The use of Cetol was more efficient, giving greater stability in the conservation of wood color of the species studied.

Added economic value of limited area multi-EPS weather forecasting applications

Directory of Open Access Journals (Sweden)

Alex Deckmyn

2012-07-01

Full Text Available We compare the GLAMEPS system, a pan-European limited area ensemble prediction system, with ECMWF's EPS over Belgium for an extended period from March 2010 until the end of December 2010. In agreement with a previous study, we find GLAMEPS scores considerably better than ECMWF's EPS. To compute the economic value, we introduce a new relative economic value score for continuous forecasts. The added value of combining the GLAMEPS system with the LAEF system over Belgium is studied. We conclude that adding LAEF to GLAMEPS increases the value, although the increase is small compared to the improvement of GLAMEPS to ECMWF's EPS. As an added benefit we find that the combined GLAMEPS-LAEF multi-EPS system is more robust, that is, it is less vulnerable to the (accidental removal of one of its components.

Evaluation of Value Added Tax Application Problems in Terms of Taxation of Electronic Commerce

OpenAIRE

Güneş ÇETİN GERGER; Adnan GERÇEK

2016-01-01

Nowadays electronic taxation is being one of the important issues for revenue administrations. Tax administrations try to organize their tax system fairly and give attention on equity. Value added tax is most preferable taxes among the consumption taxes. Because it’s application is easy and taxpayers don’t show resistance to the value added tax. On electronic commerce value added taxes are using commonly. To provide equity in taxation, some taxation principles are adapted for value added tax...

The effects of early diagenesis on the chemical and stable carbon isotopic composition of wood

International Nuclear Information System (INIS)

Spiker, E.C.; Hatcher, P.G.

1987-01-01

Studies of modern and ancient buried wood show that there is a linear correlation between carbohydrate content and the stable carbon isotope composition as carbohydrates are preferentially degraded during early diagenesis. As the carbohydrate content decreases, the delta 13 C value of the degraded wood decreases 1 to 2 per mil, approaching the value of the residual lignin. These results indicate that carbohydrate degradation products are lost and not incorporated into the aromatic structure as lignin is selectively preserved during early diagenesis of wood. These results also indicate that attempts to quantify terrestrial inputs to modern sedimentary organic matter based on delta 13 C values should consider the possibility of a 1 to 2 per mil decrease in the delta 13 C value of degraded wood. (author)

Manufacture of wood-pellets doubles. Biowatti Oy started a wood pellet plant in Turenki

International Nuclear Information System (INIS)

Rantanen, M.

1999-01-01

Wood pellets have many advantages compared to other fuels. It is longest processed biofuel with favorable energy content. It is simple to use, transport and store. Heating with wood pellets is cheaper than with light fuel oil, and approximately as cheap as utilization of heavy fuel oil, about 110 FIM/MWh. The taxable price of wood pellets is about 550 FIM/t. Stokers and American iron stoves are equally suitable for combustion of wood pellets. Chip fueled stokers are preferred in Finland, but they are also suitable for the combustion of wood pellets. Wood pellets is an environmentally friendly product, because it does not increase the CO 2 load in the atmosphere, and its sulfur and soot emissions are relatively small. The wood pelletizing plant of Biowatti Oy in Turenki was started in an old sugar mill. The Turenki sugar mill was chosen because the technology of the closed sugar factory was suitable for production of wood pellets nearly as such, and required only by slight modifications. A press, designed for briquetting of sugar beat clippings makes the pellets. The Turenki mill will double the volume of wood pellet manufacture in Finland during the next few years. At the start the annual wood pellet production will be 20 000 tons, but the environmental permit allows the production to be increased to 70 000 tons. At first the mill uses planing machine chips as a raw material in the production. It is the most suitable raw material, because it is already dry (moisture content 8-10%), and all it needs is milling and pelletizing. Another possible raw material is sawdust, which moisture content is higher than with planing machine chips. Most of the wood pellets produced are exported e.g. to Sweden, Denmark and Middle Europe. In Sweden there are over 10 000 single-family houses using wood pellets. Biowatti's largest customer is a power plant located in Stockholm, which combusts annually about 200 000 tons of wood pellets

Regional identity can add value to agricultural products

Directory of Open Access Journals (Sweden)

Bradley C. Christensen

2015-04-01

Full Text Available Regional identity creation is being recognized for its economic benefits and as a strategic resource for producer communities. A regional identity is not a brand; it is built through a complicated process of developing cohesion and sharing in the industry community and communicating outside the industry community to opinion-makers and consumers. The California fine wine industry has built successful regional identities and leveraged them to add value to their wines. As regional identities in the wine industry have strengthened, so has the industry, and a symbiotic relationship with other local value-added industries, such as tourism and hospitality, has emerged. Other agricultural producers can learn from the identity creation experiences in the wine industry. With the many challenges faced by California agriculture, identity formation may offer producers new ideas for adding value to their products and finding larger markets.

Amendments to the Law on Value Added Tax in Kosovo

Directory of Open Access Journals (Sweden)

Simeana Beshi

2016-03-01

Full Text Available Main purpose of this paper is to explore and analyze the objectives and effects of amendments in the Law on Value Added Tax (VAT as part of the new fiscal package in Kosovo. This paper is based on a quantitative analysis. Some of the methods used in this paperwork are: historical- , descriptive-, and comparative method. It relies on facts and researches conducted by international organizations, based on productive forces and on the development of economic capacities in general, also a comparative overview of the fiscal policies applied in different states. This paper presents also the challenges of Kosovo, towards EU, by harmonizing tax legislation, fiscal policy and combating tax evasion.

Justification of the Production Process of Pressed Wood and Study of its Properties

Science.gov (United States)

Polilov, A. N.; Dornyak, O. R.; Shamaev, V. A.; Rumachik, M. M.

2018-05-01

Results of a numerical analysis of the stress-strain state of wood during its pressing in different symmetry directions of the anisotropic material are presented. It is shown that the anisotropy of mechanical properties of wood is an important factor determining both the structural characteristics of the porous system and its strength. A mathematical modeling of the process of pressing wood as a three-phase anisotropic rheologically complex capillary-porous system allows one to predict parameters of the resulting wood composite. The compressed wood obtained by the production modes developed has a tensile strength eight times greater than that of the natural one, which is comparable to the strength of the St3 steel, but its specific strength is higher than that of the St45 steel. Compression and impregnation of softwood species with an aqueous solution of carbamide allows one to harden them. This kind of treatment endows the wood with enhanced strength characteristics comparable to the characteristics of the St3 steel. The special features of tensile tests used to estimate the elastic modulus and strength characteristics of such materials are considered. Data obtained by different testing methods are correlated, and characteristics of the strengthened wood and some brends of steel are compared.