Validation of CATHENA MOD-3.5/Rev0 for single-phase water hammer

International Nuclear Information System (INIS)

Beuthe, T.G.

2000-01-01

This paper describes work performed to validate the system thermalhydraulics code CATHENA MOD-3.5c/Rev0 for single-phase water hammer. Simulations were performed and are compared quantitatively against numerical tests and experimental results from the Seven Sisters Water Hammer Facility to demonstrate CATHENA can predict the creation and propagation of pressure waves when valves are opened and closed. Simulations were also performed to show CATHENA can model the behaviour of reflected and transmitted pressure waves at area changes, dead ends, tanks, boundary conditions, and orifices in simple and more complex piping systems. The CATHENA results are shown to calculate pressure and wave propagation speeds to within 0.2% and 0.5% respectively for numerical tests and within 3.3% and 5% for experimental results respectively. These results are used to help validate CATHENA for use in single-phase water hammer analysis. They also provide assurance that the fundamental parameters needed to successfully model more complex forms of water hammer are accounted for in the MOD-3.5c/Rev0 version of CATHENA, and represent the first step in the process to validate the code for use in modelling two-phase water hammer and condensation-induced water hammer. (author)

A Simple and Validated Reverse Phase HPLC Methodfor the Determination of Rabeprazole inPharmaceutical Dosage Forms

Directory of Open Access Journals (Sweden)

Uma Mahesh Karra

2010-01-01

Full Text Available A simple and rapid reverse phase high performance liquid chromatography (RP-HPLC method was developed and validated for quantitative determination of rabeprazole in bulk drug samples and formulations. Rabeprazole was analyzed by using reverse phase LC-GC column (Inertsil ODS, 4.6 mm x 25 cm, 5 microns, with mobile phase consisting of methanol: water (78:22 v/v. The flow rate was set 1.0 mL/min and analysis was performed at wavelength 288 nm using Photo Diode Array (PDA detector at ambient temperature. The method was validated and stability studies were conducted under different conditions. The retention time for rabeprazole was around 4.12 minutes. The calibration curves were linear (r≥0.9998 over a concentration range from 20.0 to 80.0 μg/mL. Limit of detection (LOD and Limit of quantitation (LOQ were 8 ng/mL and 24 ng/mL respectively. The developed method was successfully applied to estimate the amount of rabeprazole in tablet formulations.

Validated Reverse Phase HPLC Method for the Determination of Impurities in Etoricoxib

Directory of Open Access Journals (Sweden)

S. Venugopal

2011-01-01

Full Text Available This paper describes the development of reverse phase HPLC method for etoricoxib in the presence of impurities and degradation products generated from the forced degradation studies. The drug substance was subjected to stress conditions of hydrolysis, oxidation, photolysis and thermal degradation. The degradation of etoricoxib was observed under base and oxidation environment. The drug was found stable in other stress conditions studied. Successful separation of the drug from the process related impurities and degradation products were achieved on zorbax SB CN (250 x 4.6 mm 5 μm particle size column using reverse phase HPLC method. The isocratic method employed with a mixture of buffer and acetonitrile in a ratio of 60:40 respectively. Disodium hydrogen orthophosphate (0.02 M is used as buffer and pH adjusted to 7.20 with 1 N sodium hydroxide solution. The HPLC method was developed and validated with respect to linearity, accuracy, precision, specificity and ruggedness.

JaCVAM-organized international validation study of the in vivo rodent alkaline comet assay for the detection of genotoxic carcinogens: I. Summary of pre-validation study results.

Science.gov (United States)

Uno, Yoshifumi; Kojima, Hajime; Omori, Takashi; Corvi, Raffaella; Honma, Masamistu; Schechtman, Leonard M; Tice, Raymond R; Burlinson, Brian; Escobar, Patricia A; Kraynak, Andrew R; Nakagawa, Yuzuki; Nakajima, Madoka; Pant, Kamala; Asano, Norihide; Lovell, David; Morita, Takeshi; Ohno, Yasuo; Hayashi, Makoto

2015-07-01

The in vivo rodent alkaline comet assay (comet assay) is used internationally to investigate the in vivo genotoxic potential of test chemicals. This assay, however, has not previously been formally validated. The Japanese Center for the Validation of Alternative Methods (JaCVAM), with the cooperation of the U.S. NTP Interagency Center for the Evaluation of Alternative Toxicological Methods (NICEATM)/the Interagency Coordinating Committee on the Validation of Alternative Methods (ICCVAM), the European Centre for the Validation of Alternative Methods (ECVAM), and the Japanese Environmental Mutagen Society/Mammalian Mutagenesis Study Group (JEMS/MMS), organized an international validation study to evaluate the reliability and relevance of the assay for identifying genotoxic carcinogens, using liver and stomach as target organs. The ultimate goal of this validation effort was to establish an Organisation for Economic Co-operation and Development (OECD) test guideline. The purpose of the pre-validation studies (i.e., Phase 1 through 3), conducted in four or five laboratories with extensive comet assay experience, was to optimize the protocol to be used during the definitive validation study. Copyright © 2015 Elsevier B.V. All rights reserved.

Assessing validity of observational intervention studies - the Benchmarking Controlled Trials.

Science.gov (United States)

Malmivaara, Antti

2016-09-01

Benchmarking Controlled Trial (BCT) is a concept which covers all observational studies aiming to assess impact of interventions or health care system features to patients and populations. To create and pilot test a checklist for appraising methodological validity of a BCT. The checklist was created by extracting the most essential elements from the comprehensive set of criteria in the previous paper on BCTs. Also checklists and scientific papers on observational studies and respective systematic reviews were utilized. Ten BCTs published in the Lancet and in the New England Journal of Medicine were used to assess feasibility of the created checklist. The appraised studies seem to have several methodological limitations, some of which could be avoided in planning, conducting and reporting phases of the studies. The checklist can be used for planning, conducting, reporting, reviewing, and critical reading of observational intervention studies. However, the piloted checklist should be validated in further studies. Key messages Benchmarking Controlled Trial (BCT) is a concept which covers all observational studies aiming to assess impact of interventions or health care system features to patients and populations. This paper presents a checklist for appraising methodological validity of BCTs and pilot-tests the checklist with ten BCTs published in leading medical journals. The appraised studies seem to have several methodological limitations, some of which could be avoided in planning, conducting and reporting phases of the studies. The checklist can be used for planning, conducting, reporting, reviewing, and critical reading of observational intervention studies.

Three-dimensionally Functionalized Reverse Phase Glycoprotein Array for Cancer Biomarker Discovery and Validation

OpenAIRE

Pan, Li; Aguilar, Hillary Andaluz; Wang, Linna; Iliuk, Anton; Tao, W. Andy

2016-01-01

Glycoproteins have vast structural diversity which plays an important role in many biological processes and have great potential as disease biomarkers. Here we report a novel functionalized reverse phase protein array (RPPA), termed polymer-based reverse phase GlycoProtein Array (polyGPA), to specifically capture and profile glycoproteomes, and validate glycoproteins. Nitrocellulose membrane functionalized with globular hydroxyaminodendrimers was used to covalently capture pre-oxidized glycan...

Turbulence-induced bubble collision force modeling and validation in adiabatic two-phase flow using CFD

Energy Technology Data Exchange (ETDEWEB)

Sharma, Subash L., E-mail: sharma55@purdue.edu [School of Nuclear Engineering, Purdue University, West Lafayette, IN 47907-1290 (United States); Hibiki, Takashi; Ishii, Mamoru [School of Nuclear Engineering, Purdue University, West Lafayette, IN 47907-1290 (United States); Brooks, Caleb S. [Department of Nuclear, Plasma, and Radiological Engineering, University of Illinois, Urbana, IL 61801 (United States); Schlegel, Joshua P. [Nuclear Engineering Program, Missouri University of Science and Technology, Rolla, MO 65409 (United States); Liu, Yang [Nuclear Engineering Program, Department of Mechanical Engineering, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Buchanan, John R. [Bechtel Marine Propulsion Corporation, Bettis Laboratory, West Mifflin, PA 15122 (United States)

2017-02-15

Highlights: • Void distribution in narrow rectangular channel with various non-uniform inlet conditions. • Modeling of void diffusion due to bubble collision force. • Validation of new modeling in adiabatic air–water two-phase flow in a narrow channel. - Abstract: The prediction capability of the two-fluid model for gas–liquid dispersed two-phase flow depends on the accuracy of the closure relations for the interfacial forces. In previous studies of two-phase flow Computational Fluid Dynamics (CFD), interfacial force models for a single isolated bubble has been extended to disperse two-phase flow assuming the effect in a swarm of bubbles is similar. Limited studies have been performed investigating the effect of the bubble concentration on the lateral phase distribution. Bubbles, while moving through the liquid phase, may undergo turbulence-driven random collision with neighboring bubbles without significant coalescence. The rate of these collisions depends upon the bubble approach velocity and bubble spacing. The bubble collision frequency is expected to be higher in locations with higher bubble concentrations, i.e., volume fraction. This turbulence-driven random collision causes the diffusion of the bubbles from high concentration to low concentration. Based on experimental observations, a phenomenological model has been developed for a “turbulence-induced bubble collision force” for use in the two-fluid model. For testing the validity of the model, two-phase flow data measured at Purdue University are utilized. The geometry is a 10 mm × 200 mm cross section channel. Experimentally, non-uniform inlet boundary conditions are applied with different sparger combinations to vary the volume fraction distribution across the wider dimension. Examining uniform and non-uniform inlet data allows for the influence of the volume fraction to be studied as a separate effect. The turbulence-induced bubble collision force has been implemented in ANSYS CFX. The

U.S. Department of Energy's regional carbon sequestration partnership initiative: Update on validation and development phases

Science.gov (United States)

Rodosta, T.; Litynski, J.; Plasynski, S.; Spangler, L.; Finley, R.; Steadman, E.; Ball, D.; Gerald, H.; McPherson, B.; Burton, E.; Vikara, D.

2011-01-01

The U.S. Department of Energy (DOE) is the lead federal agency for the development and deployment of carbon sequestration technologies. The Regional Carbon Sequestration Partnerships (RCSPs) are the mechanism DOE utilizes to prove the technology and to develop human capital, stakeholder networks, information for regulatory policy, best practices documents and training to work toward the commercialization of carbon capture and storage (CCS). The RCSPs are tasked with determining the most suitable technologies, regulations, and infrastructure for carbon capture, transport, and storage in their respective geographic areas of responsibility. The seven partnerships include more than 400 state agencies, universities, national laboratories, private companies, and environmental organizations, spanning 43 states and four Canadian provinces. The Regional Partnerships Initiative is being implemented in three phases: Characterization, Validation, and Development. The initial Characterization Phase began in 2003 and was completed in 2005 and focused on characterization of CO2 storage potential within each region. It was followed by the Validation Phase, which began in 2005 and is nearing completion in 2011. The focus of the Validation Phase has been on small-scale field tests throughout the seven partnerships in various formation types such as saline, oil-bearing, and coal seams. The Validation Phase has characterized suitable CO2 storage reservoirs and identified the need for comprehensive legal and regulatory frameworks to enable commercial-scale CCS deployment. Finally, the Development Phase will consist of a series of large-scale, one-million-ton, injection tests throughout the United States and Canada. The objective of these large-scale tests is to identify the regulatory path or challenges in permitting CCS projects, to demonstrate the technology can inject CO2 safely, and to verify its permanence in geologic formations in preparation for the commercialization of geologic

Validation and Application of a New Reversed Phase HPLC Method for In Vitro Dissolution Studies of Rabeprazole Sodium in Delayed-Release Tablets

Directory of Open Access Journals (Sweden)

Md. Saddam Nawaz

2013-01-01

Full Text Available The purpose of this study was to develop and validate a new reversed phase high performance liquid chromatographic (RP-HPLC method to quantify in vitro dissolution assay of rabeprazole sodium in pharmaceutical tablet dosage form. Method development was performed on C 18, 100×4.6 mm ID, and 10 μm particle size column, and injection volume was 20 μL using a diode array detector (DAD to monitor the detection at 280 nm. The mobile phase consisted of buffer: acetonitrile at a ratio of 60 : 40 (v/v, and the flow rate was maintained at 1.0 mL/min. The method was validated in terms of suitability, linearity, specificity, accuracy, precision, stability, and sensitivity. Linearity was observed over the range of concentration 0.05–12.0 μg/mL, and the correlation coefficient was found excellent >0.999. The method was specific with respect to rabeprazole sodium, and the peak purity was found 99.99%. The method was precise and had relative standard deviations (RSD less than 2%. Accuracy was found in the range of 99.9 to 101.9%. The method was robust in different variable conditions and reproducible. This proposed fast, reliable, cost-effective method can be used as quality control tool for the estimation of rabeprazole sodium in routine dissolution test analysis.

Phase 1 study of metallic cask systems for spent fuel management from reactor to repository. Volume I. Phase 1 study summary

International Nuclear Information System (INIS)

1986-02-01

It was proposed to perform a systems evaluation of metallic cask systems in order to define and examine the use of various metallic cask concepts or combination of concepts for the overall inventory management of spent fuel starting with its discharge from reactors to its emplacement in geologic repositories. This systems evaluation occurs in three phases. This three phase systems evaluation leads to a definition and recommendation of a sound and practical metallic cask system to accomplish efficient and effective management of spent fuel in the back end of the nuclear fuel cycle. Phase 1 Study objectives: establish system-wide functional criteria and assumptions; perform the systems engineering needed to define the metallic cask concepts and their feasibility; perform a screening evaluation of the technical and economic merits of the concepts; and recommend those to be included for a more detailed systems evaluation in Phase 2. Phase 2 Study objectives: refine the system-wide functional criteria and assumptions; perform the design engineering needed to enhance the validity and workability of those concepts recommended in Phase 1; and perform a more detailed systems evaluation. Phase 3 Study objectives: conclude the systems evaluation and develop an implementation plan. Volume I presents an overview of the detailed systems evaluation presented in Volume II

Gas-liquid Two Phase Flow Modelling of Incompressible Fluid and Experimental Validation Studies in Vertical Centrifugal Casting

International Nuclear Information System (INIS)

Zhou, J X; Shen, X; Yin, Y J; Guo, Z; Wang, H

2015-01-01

In this paper, Gas-liquid two phase flow mathematic models of incompressible fluid were proposed to explore the feature of fluid under certain centrifugal force in vertical centrifugal casting (VCC). Modified projection-level-set method was introduced to solve the mathematic models. To validate the simulation results, two methods were used in this study. In the first method, the simulation result of basic VCC flow process was compared with its analytic solution. The relationship between the numerical solution and deterministic analytic solution was presented to verify the correctness of numerical algorithms. In the second method, systematic water simulation experiments were developed. In this initial experiment, special experimental vertical centrifugal device and casting shapes were designed to describe typical mold-filling processes in VCC. High speed camera system and data collection devices were used to capture flow shape during the mold-filling process. Moreover, fluid characteristic at different rotation speed (from 40rpm, 60rpmand 80rpm) was discussed to provide comparative resource for simulation results. As compared with the simulation results, the proposed mathematical models could be proven and the experimental design could help us advance the accuracy of simulation and further studies for VCC. (paper)

Validation of a Phase-Mass Characterization Concept and Interface for Acoustic Biosensors

Directory of Open Access Journals (Sweden)

Antonio Arnau

2011-04-01

Full Text Available Acoustic wave resonator techniques are widely used in in-liquid biochemical applications. The main challenges remaining are the improvement of sensitivity and limit of detection, as well as multianalysis capabilities and reliability. The sensitivity improvement issue has been addressed by increasing the sensor frequency, using different techniques such as high fundamental frequency quartz crystal microbalances (QCMs, surface generated acoustic waves (SGAWs and film bulk acoustic resonators (FBARs. However, this sensitivity improvement has not been completely matched in terms of limit of detection. The decrease on frequency stability due to the increase of the phase noise, particularly in oscillators, has made it impossible to increase the resolution. A new concept of sensor characterization at constant frequency has been recently proposed based on the phase/mass sensitivity equation: ∆φ/∆m ≈ −1/mL, where mL is the liquid mass perturbed by the resonator. The validation of the new concept is presented in this article. An immunosensor application for the detection of a low molecular weight pollutant, the insecticide carbaryl, has been chosen as a validation model.

Validation of model predictions of pore-scale fluid distributions during two-phase flow

Science.gov (United States)

Bultreys, Tom; Lin, Qingyang; Gao, Ying; Raeini, Ali Q.; AlRatrout, Ahmed; Bijeljic, Branko; Blunt, Martin J.

2018-05-01

Pore-scale two-phase flow modeling is an important technology to study a rock's relative permeability behavior. To investigate if these models are predictive, the calculated pore-scale fluid distributions which determine the relative permeability need to be validated. In this work, we introduce a methodology to quantitatively compare models to experimental fluid distributions in flow experiments visualized with microcomputed tomography. First, we analyzed five repeated drainage-imbibition experiments on a single sample. In these experiments, the exact fluid distributions were not fully repeatable on a pore-by-pore basis, while the global properties of the fluid distribution were. Then two fractional flow experiments were used to validate a quasistatic pore network model. The model correctly predicted the fluid present in more than 75% of pores and throats in drainage and imbibition. To quantify what this means for the relevant global properties of the fluid distribution, we compare the main flow paths and the connectivity across the different pore sizes in the modeled and experimental fluid distributions. These essential topology characteristics matched well for drainage simulations, but not for imbibition. This suggests that the pore-filling rules in the network model we used need to be improved to make reliable predictions of imbibition. The presented analysis illustrates the potential of our methodology to systematically and robustly test two-phase flow models to aid in model development and calibration.

Empirical Validation of a Thermal Model of a Complex Roof Including Phase Change Materials

Directory of Open Access Journals (Sweden)

Stéphane Guichard

2015-12-01

Full Text Available This paper deals with the empirical validation of a building thermal model of a complex roof including a phase change material (PCM. A mathematical model dedicated to PCMs based on the heat apparent capacity method was implemented in a multi-zone building simulation code, the aim being to increase the understanding of the thermal behavior of the whole building with PCM technologies. In order to empirically validate the model, the methodology is based both on numerical and experimental studies. A parametric sensitivity analysis was performed and a set of parameters of the thermal model has been identified for optimization. The use of the generic optimization program called GenOpt® coupled to the building simulation code enabled to determine the set of adequate parameters. We first present the empirical validation methodology and main results of previous work. We then give an overview of GenOpt® and its coupling with the building simulation code. Finally, once the optimization results are obtained, comparisons of the thermal predictions with measurements are found to be acceptable and are presented.

Phase 1 Validation Testing and Simulation for the WEC-Sim Open Source Code

Science.gov (United States)

Ruehl, K.; Michelen, C.; Gunawan, B.; Bosma, B.; Simmons, A.; Lomonaco, P.

2015-12-01

WEC-Sim is an open source code to model wave energy converters performance in operational waves, developed by Sandia and NREL and funded by the US DOE. The code is a time-domain modeling tool developed in MATLAB/SIMULINK using the multibody dynamics solver SimMechanics, and solves the WEC's governing equations of motion using the Cummins time-domain impulse response formulation in 6 degrees of freedom. The WEC-Sim code has undergone verification through code-to-code comparisons; however validation of the code has been limited to publicly available experimental data sets. While these data sets provide preliminary code validation, the experimental tests were not explicitly designed for code validation, and as a result are limited in their ability to validate the full functionality of the WEC-Sim code. Therefore, dedicated physical model tests for WEC-Sim validation have been performed. This presentation provides an overview of the WEC-Sim validation experimental wave tank tests performed at the Oregon State University's Directional Wave Basin at Hinsdale Wave Research Laboratory. Phase 1 of experimental testing was focused on device characterization and completed in Fall 2015. Phase 2 is focused on WEC performance and scheduled for Winter 2015/2016. These experimental tests were designed explicitly to validate the performance of WEC-Sim code, and its new feature additions. Upon completion, the WEC-Sim validation data set will be made publicly available to the wave energy community. For the physical model test, a controllable model of a floating wave energy converter has been designed and constructed. The instrumentation includes state-of-the-art devices to measure pressure fields, motions in 6 DOF, multi-axial load cells, torque transducers, position transducers, and encoders. The model also incorporates a fully programmable Power-Take-Off system which can be used to generate or absorb wave energy. Numerical simulations of the experiments using WEC-Sim will be

Assessing validity of observational intervention studies – the Benchmarking Controlled Trials

Science.gov (United States)

Malmivaara, Antti

2016-01-01

Abstract Background: Benchmarking Controlled Trial (BCT) is a concept which covers all observational studies aiming to assess impact of interventions or health care system features to patients and populations. Aims: To create and pilot test a checklist for appraising methodological validity of a BCT. Methods: The checklist was created by extracting the most essential elements from the comprehensive set of criteria in the previous paper on BCTs. Also checklists and scientific papers on observational studies and respective systematic reviews were utilized. Ten BCTs published in the Lancet and in the New England Journal of Medicine were used to assess feasibility of the created checklist. Results: The appraised studies seem to have several methodological limitations, some of which could be avoided in planning, conducting and reporting phases of the studies. Conclusions: The checklist can be used for planning, conducting, reporting, reviewing, and critical reading of observational intervention studies. However, the piloted checklist should be validated in further studies.Key messagesBenchmarking Controlled Trial (BCT) is a concept which covers all observational studies aiming to assess impact of interventions or health care system features to patients and populations.This paper presents a checklist for appraising methodological validity of BCTs and pilot-tests the checklist with ten BCTs published in leading medical journals. The appraised studies seem to have several methodological limitations, some of which could be avoided in planning, conducting and reporting phases of the studies.The checklist can be used for planning, conducting, reporting, reviewing, and critical reading of observational intervention studies. PMID:27238631

Contribution to the verification and the validation of an unsteady two-phase flow model

International Nuclear Information System (INIS)

Liu, Yujie

2013-01-01

This thesis contributes to the verification and the validation of the Baer-Nunziato (BN) model, to model water hammer phenomena in industrial piping systems. It consists of two parts, the first is to model water hammer flows with the BN model in Eulerian representation and the second is to extend this model to the ALE (Arbitrary Lagrangian Eulerian) formalism so as to take into account fluid-structure interaction (FSI). To model water hammer flows, closure laws of the BN model concerning the interfacial/source terms and the equations of state (EOS) were first studied. Then the whole system was simulated with a fractional step method including two steps, one for the resolution of the convective part, the other for the source terms. For the convective part, the Rusanov scheme was first checked, and some stability problems have been observed. Thus a more stable fractional step scheme has been proposed and verified. Regarding the source terms, four non-instantaneous relaxation schemes which represent the return to equilibrium of pressure, the transfers of momentum, heat and mass were successively applied. These schemes have been extended to 'generalized Stiffened Gas' EOS in order to represent phase-change. After regaining some typical phenomena associated with water hammer flows, the BN model was validated with the Simpson experiment, a classical water hammer test case, and the Canon experience, a rapid decompression of fluid in a high pressure duct. Moreover, the model was compared with two homogeneous models on these two experiments. Finally, an ALE version of the BN model was implemented, and verified on a case of wave propagation in a 'single' phase flow and a two-phase flow in a flexible pipe. The variation of wave propagation speed due to the coupling between the fluid and the structure has been well retrieved. The validation was performed on an experiment which examines the response of a pipe filled with water, subjected to a violent pressure peak (140 bar

Los Angeles International Airport Runway Incursion Studies: Phase III--Center-Taxiway Simulation

Science.gov (United States)

Madson, Michael D.

2004-01-01

Phase III of the Los Angeles International Airport Runway Incursion Studies was conducted, under an agreement with HNTB Corporation, at the NASA Ames FutureFlight Central (FFC) facility in June 2003. The objective of the study was the evaluation of a new center-taxiway concept at LAX. This study is an extension of the Phase I and Phase II studies previously conducted at FFC. This report presents results from Phase III of the study, in which a center-taxiway concept between runways 25L and 25R was simulated and evaluated. Phase III data were compared objectively against the Baseline data. Subjective evaluations by participating LAX controllers were obtained with regard to workload, efficiency, and safety criteria. To facilitate a valid comparison between Baseline and Phase III data, the same scenarios were used for Phase III that were tested during Phases I and II. This required briefing participating controllers on differences in airport and airline operations between 2001 and today.

WEC-SIM Phase 1 Validation Testing -- Numerical Modeling of Experiments: Preprint

Energy Technology Data Exchange (ETDEWEB)

Ruehl, Kelley; Michelen, Carlos; Bosma, Bret; Yu, Yi-Hsiang

2016-08-01

The Wave Energy Converter Simulator (WEC-Sim) is an open-source code jointly developed by Sandia National Laboratories and the National Renewable Energy Laboratory. It is used to model wave energy converters subjected to operational and extreme waves. In order for the WEC-Sim code to be beneficial to the wave energy community, code verification and physical model validation is necessary. This paper describes numerical modeling of the wave tank testing for the 1:33-scale experimental testing of the floating oscillating surge wave energy converter. The comparison between WEC-Sim and the Phase 1 experimental data set serves as code validation. This paper is a follow-up to the WEC-Sim paper on experimental testing, and describes the WEC-Sim numerical simulations for the floating oscillating surge wave energy converter.

OECD validation of the Hershberger assay in Japan: phase 2 dose response of methyltestosterone, vinclozolin, and p,p'-DDE.

Science.gov (United States)

Yamasaki, Kanji; Sawaki, Masakuni; Ohta, Ryo; Okuda, Hirokazu; Katayama, Seiichi; Yamada, Tomoya; Ohta, Takafumi; Kosaka, Tadashi; Owens, William

2003-01-01

The Organisation for Economic Co-operation and Development has initiated the development of new guidelines for the screening and testing of potential endocrine disruptors. The Hershberger assay is one of the assays selected for validation based on the need for in vivo screening to detect androgen agonists or antagonists by measuring the response of five sex accessory organs and tissues of castrated juvenile male rats: the ventral prostate, the seminal vesicles with coagulating glands, the levator ani and bulbocavernosus muscle complex, the Cowper's glands, and the glans penis. The phase 1 feasibility demonstration stage of the Hershberger validation program has been successfully completed with a single androgen agonist and a single antagonist as reference substances. The phase 2 validation program employs a range of additional androgen agonists and antagonists as well as 5alpha-reductase inhibitors. Seven Japanese laboratories have contributed phase 2 validation studies of the Hershberger assay using methyltestosterone, vinclozolin, and 2,2-bis (4-chlorophenyl)-1,1-dichloroethylene (p,p'-DDE). The methyltestosterone doses were 0, 0.05, 0.5, 5, and 50 mg/kg/day, and the vinclozolin and p,p'-DDE doses were 0, 3, 10, 30, and 100 mg/kg/day. All chemicals were orally administered by gavage for 10 consecutive days. In the antagonist version of the assay using vinclozolin and p,p'-DDE, 0.2 mg/kg/day of testosterone propionate was coadministered by subcutaneous injection. All five accessory sex preproductive organs and tissues consistently responded with statistically significant changes in weight within a narrow window. Therefore, the Japanese studies support the Hershberger assay as a reliable and reproducible screening assay for the detection of androgen agonistic and antagonistic effects. PMID:14644666

Toward a Measure of Accountability in Nursing: A Three-Stage Validation Study.

Science.gov (United States)

Drach-Zahavy, Anat; Leonenko, Marina; Srulovici, Einav

2018-06-04

To develop and psychometrically evaluate a three-dimensional questionnaire suitable for evaluating personal and organizational accountability in nurses. Accountability is defined as a three-dimensional value, directing professionals to take responsibility for their decisions and actions, to be willing to explain them (transparency) and to be judged according to society's accepted values (answerability). Despite the relatively clear definition, measurement of accountability lags well behind. Existing self-report questionnaires do not fully capture the complexity of the concept; nor do they capture the different sources of accountability (e.g., personal accountability, organizational accountability). A three-stage measure development. Data were collected during 2015-2016. In Phase 1, an initial database of items (N = 74) was developed, based on literature review and qualitative study, establishing face and content validity. In Phase 2, the face, content, construct and criterion-related validity of the initial questionnaires (19 items for personal and organizational accountability questionnaire) was established with a sample of 229 nurses. In Phase 3, the final questionnaires (19 items each) were validated with a new sample of 329 nurses and established construct validity. The final version of the instruments comprised 19 items, suitable for assessing personal and organizational accountability. The questionnaire referred to the dimensions of responsibility, transparency and answerability. The findings established the instrument's content, construct and criterion-related validity, as well as good internal reliability. The questionnaire portrays accountability in nursing, by capturing nurses' subjective perceptions of accountability dimensions (responsibility, transparency, answerability), as demonstrated by personal and organizational values. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

VALIDATION REPORT (PHASE 2) FOR THE FISH SEXUAL DEVELOPMENT TEST FOR THE DETECTION OF ENDOCRINE ACTIVE SUBSTANCES

DEFF Research Database (Denmark)

Holbech, Henrik; Kinnberg, Karin Lund; Petersen, Gitte

This document presents the validation report (phase 2) of the Fish Sexual Development Test (FSDT). The Fish Sexual Development Test (FSDT) covers a life-stage where sexual development is particularly sensitive to perturbation caused by endocrine active chemicals. The chemical exposure lasts...... Guideline on the fish sexual development test to the Working Group of the National Coordinators of the Test Guidelines Programme (WNT). The project was included on the Test Guidelines workplan in 2003, and extensive validation of the test method was carried out until 2009. Two validation studies were...... for about 60 days, at the end of which endpoints of ecological relevance like the sex ratio of the exposed fish is calculated and the biomarker endpoint vitellogenin is measured in individual animals. In 2003, Denmark, on behalf of the European Nordic countries, proposed a new project o develop a Test...

Validation of DRAGON side-step method for Bruce-A restart Phase-B physics tests

International Nuclear Information System (INIS)

Shen, W.; Ngo-Trong, C.; Davis, R.S.

2004-01-01

The DRAGON side-step method, developed at AECL, has a number of advantages over the all-DRAGON method that was used before. It is now the qualified method for reactivity-device calculations. Although the side-step-method-generated incremental cross sections have been validated against those previously calculated with the all-DRAGON method, it is highly desirable to validate the side-step method against device-worth measurements in power reactors directly. In this paper, the DRAGON side-step method was validated by comparison with the device-calibration measurements made in Bruce-A NGS Unit 4 restart Phase-B commissioning in 2003. The validation exercise showed excellent results, with the DRAGON code overestimating the measured ZCR worth by ∼5%. A sensitivity study was also performed in this paper to assess the effect of various DRAGON modelling techniques on the incremental cross sections. The assessment shows that the refinement of meshes in 3-D and the use of the side-step method are two major reasons contributing to the improved agreement between the calculated ZCR worths and the measurements. Use of different DRAGON versions, DRAGON libraries, local-parameter core conditions, and weighting techniques for the homogenization of tube clusters inside the ZCR have a very small effect on the ZCR incremental thermal absorption cross section and ZCR reactivity worth. (author)

Rapid Robot Design Validation, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Energid Technologies will create a comprehensive software infrastructure for rapid validation of robot designs. The software will support push-button validation...

Validation summary report for the 100-HR-3 Groundwater Round 9 Phase 1 and 2

International Nuclear Information System (INIS)

1996-02-01

This report presents a summary of data validation results on groundwater samples collected for the 100-HR-3 Groundwater Round 9-Phase I and II Project. The analyses performed for this project were as follows: Metals--inductively coupled plasma (ICP) metals (filtered and unfiltered); General Chemistry--anions (fluoride, chloride, nitrate, nitrite, phosphate, and sulfate), turbidity, ammonia, nitrate+nitrite, and sulfide; and Radiochemistry--gross alpha, gross beta, technetium-99, tritium, and uranium-234/235/238. The objectives of this project were to validate sample detection limit as defined in the data validation procedures (WHC 1993). In addition, this report provides a summary of the data as defined by laboratory performance criteria and project-specific data quality objectives

Development of caries risk assessment tool for Iranian preschoolers: A primary validation study

Directory of Open Access Journals (Sweden)

Shiva Mortazavi

2017-01-01

Full Text Available Background: The aim of the present study was to develop a dental caries risk assessment tool for Iranian preschoolers. Methods: In a validation and cross-sectional study, a random sample of 150 preschool children was involved. This study was conducted in three phases: questionnaire design (expert panel and peer evaluation, questionnaire testing (pilot evaluation and field testing, and validation study. The initial assessments include interview, dental examination, and laboratory investigations. Validity and reliability indices, content validity index (CVI, content validity ratio (CVR, impact score, and test-retest and Cronbach's alpha were measured. Decayed, missing, filled teeth (dmft scores were calculated according to the WHO guidelines. Results: The Iranian version of caries risk assessment (CRA questionnaire contained 17 items. Cronbach's alpha coefficient (0.86 indicated a suitable internal consistency. The mean scores for the CVI and the CVR were 0.87 and 0.78, respectively. The prevalence rate of dental caries in the study group was 69.3%, and the mean dmft was 4.57 (range 0–19. Conclusions: The Persian version of CRA questionnaire was adapted to the Iranian population. The findings demonstrated overall acceptable validity and also reliability in the application of test-retest. The results of the present study provide initial evidence that the designed CRA form could be a useful tool for CRA in the Iranian preschoolers.

OC5 Project Phase Ib: Validation of Hydrodynamic Loading on a Fixed, Flexible Cylinder for Offshore Wind Applications

DEFF Research Database (Denmark)

Robertson, Amy N.; Wendt, Fabian; Jonkman, Jason M.

2016-01-01

at the Danish Hydraulic Institute (DHI) with support from the Technical University of Denmark (DTU). The first phase of OC5 examined two simple cylinder structures (Phase Ia and Ib) to focus on validation of hydrodynamic models used in the various tools before moving on to more complex offshore wind systems...

Two-phase 1D+1D model of a DMFC: development and validation on extensive operating conditions range

Energy Technology Data Exchange (ETDEWEB)

Casalegno, A.; Marchesi, R.; Parenti, D. [Dipartimento di Energetica, Politecnico di Milano (Italy)

2008-02-15

A two-phase 1D+1D model of a direct methanol fuel cell (DMFC) is developed, considering overall mass balance, methanol transport in gas phase through anode diffusion layer, methanol and water crossover. The model is quantitatively validated on an extensive range of operating conditions, 24 polarisation curves. The model accurately reproduces DMFC performance in the validation range and, outside this, it is able to predict values under feasible operating conditions. Finally, the estimations of methanol crossover flux are qualitatively and quantitatively similar to experimental measures and the main local quantities' trends are coherent with results obtained with more complex models. (Abstract Copyright [2008], Wiley Periodicals, Inc.)

Investigation of a two-phase nozzle flow and validation of several computer codes by the experimental data

International Nuclear Information System (INIS)

Kedziur, F.

1980-03-01

Stationary experiments with a convergent nozzle are performed in order to validate advanced two-phase computer codes, which find application in the blowdown-phase of a loss-of-coolant accident (LOCA). The steam/water flow presents a broad variety of initial conditions: The pressure varies between 2 and 13 MPa, the void fraction between 0 (subcooled) and about 80%, a great number of subcritical as well as critical experiments with different flow pattern is investigated. Additional air/water experiments serve for the separation of phase transition effects. The transient acceleration of the fluid in the LOCA-case is simulated by a local acceleration in the experiments. The layout of the nozzle and the applied measurement technique allow for a separate testing of physical models and the determination of empirical model parameters, respectively: In the four codes DUESE, DRIX-20, RELAP4/MOD6 and STRUYA the models - if they exist - for slip between the phases, thermodynamic non-equilibrium, pipe friction and critical mass flow rate are validated and criticised in comparison with the experimental data, and the corresponding model parameters are determined. The parameters essentially are a function of the void fraction. (orig.) [de

EXPERIMENTAL RESULTS OF THE NEPHELINE PHASE III STUDY

Energy Technology Data Exchange (ETDEWEB)

Fox, K.; Edwards, T.

2009-11-09

This study is the third phase in a series of experiments designed to reduce conservatism in the model that predicts the formation of nepheline, a crystalline phase that can reduce the durability of high level waste glass. A Phase I study developed a series of glass compositions that were very durable while their nepheline discriminator values were well below the current nepheline discriminator limit of 0.62, where nepheline is predicted to crystallize upon slow cooling. A Phase II study selected glass compositions to identify any linear effects of composition on nepheline crystallization and that were restricted to regions that fell within the validation ranges of the Defense Waste Processing Facility (DWPF) Product Composition Control System (PCCS) models. However, it was not possible to identify any linear effects of composition on chemical durability performance for this set of study glasses. The results of the Phase II study alone were not sufficient to recommend modification of the current nepheline discriminator. It was recommended that the next series of experiments continue to focus not only on compositional regions where the PCCS models are considered applicable (i.e., the model validation ranges), but also be restricted to compositional regions where the only constraint limiting processing is the current nepheline discriminator. Two methods were used in selecting glasses for this Phase III nepheline study. The first was based on the relationship of the current nepheline discriminator model to the other DWPF PCCS models, and the second was based on theory of crystallization in mineral and glass melts. A series of 29 test glass compositions was selected for this study using a combination of the two approaches. The glasses were fabricated and characterized in the laboratory. After reviewing the data, the study glasses generally met the target compositions with little issue. Product Consistency Test results correlated well with the crystallization analyses in

Validation of the Five-Phase Method for Simulating Complex Fenestration Systems with Radiance against Field Measurements

Energy Technology Data Exchange (ETDEWEB)

Geisler-Moroder, David [Bartenbach GmbH, Aldrans (Austria); Lee, Eleanor S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ward, Gregory J. [Anyhere Software, Albany, NY (United States)

2016-08-29

The Five-Phase Method (5-pm) for simulating complex fenestration systems with Radiance is validated against field measurements. The capability of the method to predict workplane illuminances, vertical sensor illuminances, and glare indices derived from captured and rendered high dynamic range (HDR) images is investigated. To be able to accurately represent the direct sun part of the daylight not only in sensor point simulations, but also in renderings of interior scenes, the 5-pm calculation procedure was extended. The validation shows that the 5-pm is superior to the Three-Phase Method for predicting horizontal and vertical illuminance sensor values as well as glare indices derived from rendered images. Even with input data from global and diffuse horizontal irradiance measurements only, daylight glare probability (DGP) values can be predicted within 10% error of measured values for most situations.

Physical validation issue of the NEPTUNE two-phase modelling: validation plan to be adopted, experimental programs to be set up and associated instrumentation techniques developed

International Nuclear Information System (INIS)

Pierre Peturaud; Eric Hervieu

2005-01-01

Full text of publication follows: A long-term joint development program for the next generation of nuclear reactors simulation tools has been launched in 2001 by EDF (Electricite de France) and CEA (Commissariat a l'Energie Atomique). The NEPTUNE Project constitutes the Thermal-Hydraulics part of this comprehensive program. Along with the underway development of this new two-phase flow software platform, the physical validation of the involved modelling is a crucial issue, whatever the modelling scale is, and the present paper deals with this issue. After a brief recall about the NEPTUNE platform, the general validation strategy to be adopted is first of all clarified by means of three major features: (i) physical validation in close connection with the concerned industrial applications, (ii) involving (as far as possible) a two-step process successively focusing on dominant separate models and assessing the whole modelling capability, (iii) thanks to the use of relevant data with respect to the validation aims. Based on this general validation process, a four-step generic work approach has been defined; it includes: (i) a thorough analysis of the concerned industrial applications to identify the key physical phenomena involved and associated dominant basic models, (ii) an assessment of these models against the available validation pieces of information, to specify the additional validation needs and define dedicated validation plans, (iii) an inventory and assessment of existing validation data (with respect to the requirements specified in the previous task) to identify the actual needs for new validation data, (iv) the specification of the new experimental programs to be set up to provide the needed new data. This work approach has been applied to the NEPTUNE software, focusing on 8 high priority industrial applications, and it has resulted in the definition of (i) the validation plan and experimental programs to be set up for the open medium 3D modelling

Determination of maduramicin in feedingstuffs and premixtures by liquid chromatography : development, validation and interlaboratory study

NARCIS (Netherlands)

Jong, de J.; Stoisser, B.; Wagner, K.; Tomassen, M.J.H.; Driessen, J.J.M.; Hofman, P.; Putzka, H.A.

2004-01-01

A reversed-phase liquid chromatography method for determination of maduramicin in feedingstuffs and premixtures was developed, validated, and interlaboratory studied. The extraction solvent was methanol. Maduramicin was detected at 520 nm after postcolumn derivatization with vanillin. Recovery was

Development and validity data of the Brazilian Internet Study on Temperament and Psychopathology (BRAINSTEP).

Science.gov (United States)

Lara, Diogo R; Ottoni, Gustavo L; Brunstein, Miriam G; Frozi, Julia; de Carvalho, Hudson W; Bisol, Luísa W

2012-12-10

The internet provides a research opportunity for psychiatry and psychology. This article presents the development and preliminary data of a large web-survey created to study how temperament relates to other psychological measures, behavior and psychiatric disorders. We used the Affective and Emotional Composite Temperament Scale (AFECTS) to evaluate temperament and we selected several self-report instruments to evaluate behavior, psychological constructs and mental disorders. The system provides anonymous psychological (phase 1) and psychiatric (phase 2) feedback and includes questions to assess the validity of the answers. Each phase has around 450 questions. This system was broadcast utilizing Brazilian media. After the exclusion of 21.5% of the volunteers (those who failed the validation questions), 41,427 participants concluded the first part of the system (mean age=31.2±10.5 yrs, 26.9% males), and 21,836 (mean age=32.5±10.9 yrs, 25.1% males) completed phase 2. Around 25% have received a psychiatric diagnosis from a mental health professional. Demographic and temperament profiles of those who completed either only 80 questions, only phase 1, or the whole system were similar. The rate of non-serious answers (e.g. on bizarre behaviors) was very low and congruency of answers was very high. The internal consistency of classical trait scales (TCI-R and PANAS) was high (Cronbach's alpha>0.80) for all dimensions. Relatively high dropout rate due to the length of the process and an overrepresentation of female, young and well-educated subjects. The BRAINSTEP provides valid and abundant data on psychological and psychiatric measures. Copyright © 2012 Elsevier B.V. All rights reserved.

The OECD validation program of the H295R steroidogenesis assay: Phase 3. Final inter-laboratory validation study

DEFF Research Database (Denmark)

Hecker, Markus; Hollert, Henner; Cooper, Ralph

2011-01-01

In response to increasing concerns regarding the potential of chemicals to interact with the endocrine system of humans and wildlife, various national and international programs have been initiated with the aim to develop new guidelines for the screening and testing of these chemicals in vertebra......In response to increasing concerns regarding the potential of chemicals to interact with the endocrine system of humans and wildlife, various national and international programs have been initiated with the aim to develop new guidelines for the screening and testing of these chemicals...... in vertebrates. Here, we report on the validation of an in vitro assay, the H295R steroidogenesis assay, to detect chemicals with the potential to inhibit or induce the production of the sex steroid hormones testosterone (T) and 17β-estradiol (E2) in preparation for the development of an Organization...... for Economic Cooperation and Development (OECD) test guideline.A previously optimized and pre-validated protocol was used to assess the potential of 28 chemicals of diverse structures and properties to validate the H295R steroidogenesis assay. These chemicals are comprised of known endocrine-active chemicals...

Experimental Validation of Pulse Phase Tracking for X-Ray Pulsar Based

Science.gov (United States)

Anderson, Kevin

2012-01-01

Pulsars are a form of variable celestial source that have shown to be usable as aids for autonomous, deep space navigation. Particularly those sources emitting in the X-ray band are ideal for navigation due to smaller detector sizes. In this paper X-ray photons arriving from a pulsar are modeled as a non-homogeneous Poisson process. The method of pulse phase tracking is then investigated as a technique to measure the radial distance traveled by a spacecraft over an observation interval. A maximum-likelihood phase estimator (MLE) is used for the case where the observed frequency signal is constant. For the varying signal frequency case, an algorithm is used in which the observation window is broken up into smaller blocks over which an MLE is used. The outputs of this phase estimation process were then looped through a digital phase-locked loop (DPLL) in order to reduce the errors and produce estimates of the doppler frequency. These phase tracking algorithms were tested both in a computer simulation environment and using the NASA Goddard Space flight Center X-ray Navigation Laboratory Testbed (GXLT). This provided an experimental validation with photons being emitted by a modulated X-ray source and detected by a silicon-drift detector. Models of the Crab pulsar and the pulsar B1821-24 were used in order to generate test scenarios. Three different simulated detector trajectories were used to be tracked by the phase tracking algorithm: a stationary case, one with constant velocity, and one with constant acceleration. All three were performed in one-dimension along the line of sight to the pulsar. The first two had a constant signal frequency and the third had a time varying frequency. All of the constant frequency cases were processed using the MLE, and it was shown that they tracked the initial phase within 0.15% for the simulations and 2.5% in the experiments, based on an average of ten runs. The MLE-DPLL cascade version of the phase tracking algorithm was used in

Validation of KENOREST with LWR-PROTEUS phase II samples

Energy Technology Data Exchange (ETDEWEB)

Wagner, M.; Kilger, R.; Pautz, A.; Zwermann, W. [GRS, Garching (Germany); Grimm, P.; Vasiliev, A.; Ferroukhi, H. [Paul Scherrer Institut, Villigen (Switzerland)

2012-11-01

In order to broaden the validation basis of the reactivity and nuclide inventory code KENOREST two samples of the LWR-PROTEUS phase II program have been calculated and compared to the experimental results. In general most nuclides are reproduced very well and agree within about ten percent with the experiment. Some already known problems, the overprediction of metallic fission products and the underprediction of the higher curium isotopes, have been confirmed. One of the largest uncertainties in the calculation was the burnup of the samples due to differences between a core simulation of the fuel vendor and the burnup determined from the measured values of the burnup indicator Nd-148. Two different models taking into account the environment for a peripheral fuel rod have been studied. The more detailed model included the three direct neighbor fuel assemblies depleted along with the fuel rod of interest. The influence on the results has been found to be very small. Compared to the uncertainties from the burnup, this effect can be considered negligible. The reason for the low influence was basically that the spectrum did not get considerably harder with increasing burnup beyond about 20GWd/tHM. Since the sample reached burnups far beyond that value, an effect could not be seen. In the near future an update of the used libraries is planned and it will be very interesting to study the effect on the results, especially for Curium. (orig.)

Validation of two-phase flow code THYC on VATICAN experiment

International Nuclear Information System (INIS)

Maurel, F.; Portesse, A.; Rimbert, P.; Thomas, B.

1997-01-01

As part of a comprehensive program for THYC validation (THYC is a 3-dimensional two-phase flow computer code for PWR core configuration), an experimental project > has been initiated by the Direction des Etudes et Recherches of Electricite de France. Two mock-ups tested in Refrigerant-114, VATICAN-1 (with simple space grids) and VATICAN-2 (with mixing grids) were set up to investigate void fraction distributions using a single beam gamma densitometer. First, experiments were conducted with the VATICAN-1 mock-up. A set of constitutive laws to be used in rod bundles was determined but some doubts still remain for friction losses closure laws for oblique flow over tubes. From VATICAN-2 tests, calculations were performed using the standard set of correlations. Comparison with the experimental data shows an underprediction of void fraction by THYC in disturbed regions. Analyses highlight the poor treatment of axial relative velocity in these regions. A fitting of the radial and axial relative velocity values in the disturbed region improves the prediction of void fraction by the code but without any physical explanation. More analytical experiments should be carried out to validate friction losses closure laws for oblique flows and relative velocity downstream of a mixing grid. (author)

Validation of two-phase flow code THYC on VATICAN experiment

Energy Technology Data Exchange (ETDEWEB)

Maurel, F.; Portesse, A.; Rimbert, P.; Thomas, B. [EDF/DER, Dept. TTA, 78 - Chatou (France)

1997-12-31

As part of a comprehensive program for THYC validation (THYC is a 3-dimensional two-phase flow computer code for PWR core configuration), an experimental project <> has been initiated by the Direction des Etudes et Recherches of Electricite de France. Two mock-ups tested in Refrigerant-114, VATICAN-1 (with simple space grids) and VATICAN-2 (with mixing grids) were set up to investigate void fraction distributions using a single beam gamma densitometer. First, experiments were conducted with the VATICAN-1 mock-up. A set of constitutive laws to be used in rod bundles was determined but some doubts still remain for friction losses closure laws for oblique flow over tubes. From VATICAN-2 tests, calculations were performed using the standard set of correlations. Comparison with the experimental data shows an underprediction of void fraction by THYC in disturbed regions. Analyses highlight the poor treatment of axial relative velocity in these regions. A fitting of the radial and axial relative velocity values in the disturbed region improves the prediction of void fraction by the code but without any physical explanation. More analytical experiments should be carried out to validate friction losses closure laws for oblique flows and relative velocity downstream of a mixing grid. (author)

Phase Stability in the Mo-Ti-Zr-C System via Thermodynamic Modeling and Diffusion Multiple Validation

Science.gov (United States)

Kar, Sujoy Kumar; Dheeradhada, Voramon S.; Lipkin, Don M.

2013-08-01

Alloys in the Mo-rich corner of the Mo-Ti-Zr-C system have found broad applications in non-oxidizing environments requiring structural integrity well beyond 1273 K (1000 °C). Alloys such as TZM (Mo-0.5Ti-0.08Zr-0.03C by weight %) and TZC (Mo-1.2Ti-0.3Zr-0.1C by weight) owe much of their high temperature strength and microstructural stability to MC and M2C carbide phases. In turn, the stability of the respective carbides and the subsequent mechanical behavior of the alloys are strongly dependent on the alloying additions and thermal history. A CALPHAD-based thermodynamic modeling approach is employed to develop a quaternary thermodynamic database for the Mo-Ti-Zr-C system. The thermodynamic database thus developed is validated with diffusion multiple experiments and the validated database is exercised to elucidate the effects of alloying and thermal history on the phase equilibrium in Mo-rich alloys.

The international phase 4 validation study of the EORTC QLQ-SWB32: A stand-alone measure of spiritual well-being for people receiving palliative care for cancer

NARCIS (Netherlands)

Vivat, B.; Young, T. E.; Winstanley, J.; Arraras, J. I.; Black, K.; Boyle, F.; Bredart, A.; Costantini, A.; Guo, J.; Irarrazaval, M. E.; Kobayashi, K.; Kruizinga, R.; Navarro, M.; Omidvari, S.; Rohde, G. E.; Serpentini, S.; Spry, N.; van Laarhoven, H. W. M.; Yang, G. M.

2017-01-01

The EORTC Quality of Life Group has just completed the final phase (field-testing and validation) of an international project to develop a stand-alone measure of spiritual well-being (SWB) for palliative cancer patients. Participants (n = 451)-from 14 countries on four continents; 54% female; 188

Methodologies for verification and validation of expert systems as a function of component, criticality and life-cycle phase

International Nuclear Information System (INIS)

Miller, L.

1992-01-01

The review of verification and validation (V and V) methods presented here is based on results of the initial two tasks of a contract with the US Nuclear Regulatory Commission and the Electric Power Research Institute to Develop and Document Guidelines for Verifying and Validating Expert Systems. The first task was to review the applicability of conventional software techniques to expert systems; the second was to directly survey V and V practices associated with development of expert systems. Subsequent tasks will focus on selecting, synthesizing or developing V and V methods appropriate for the overall system, for specific expert systems components, and for different phases of the life-cycle. In addition, final guidelines will most likely be developed for each of three levels of expert systems: safety-related (systems whose functions directly relate to system safety, so-called safety-critical systems), important-to-safety (systems which support the critical safety functions), and non-safety (systems which are unrelated to safety functions). For the present purposes of categorizing and discussing various types of V and V methods, the authors simplify the life-cycle and consider only two aspects - systems validation phase. The authors identified a number of techniques for the first, combined, phase and two general classes of V and V techniques for the latter phase: static testing techniques, which do not involve execution of the system code, and dynamic testing techniques, which do. In the next two sections the author reviews first the applicability to expert systems of conventional V and V techniques and, second, the techniques expert system developers actually use. In the last section the authors make some general observations

The COSIMA-experiments, a data base for validation of two-phase flow computer codes

International Nuclear Information System (INIS)

Class, G.; Meyder, R.; Stratmanns, E.

1985-12-01

The report presents an overview on the large data base generated with COSIMA. The data base is to be used to validate and develop computer codes for two-phase flow. In terms of fuel rod behavior it was found that during blowdown under realistic conditions only small strains are reached. For clad rupture extremely high rod internal pressure is necessary. Additionally important results were found in the behavior of a fuel rod simulator and on the effect of thermocouples attached on the cladding outer surface. Post-test calculations, performed with the codes RELAP and DRUFAN show a good agreement with the experiments. This however can be improved if the phase separation models in the codes would be updated. (orig./HP) [de

ASSESSMENT OF SATISFACTION IN PERITONEAL EQUILIBRATION TEST: A STUDY ON THE VALIDITY AND RELIABILITY OF THE PERITONEAL EQUILIBRATION SATISFACTION SCALE

Directory of Open Access Journals (Sweden)

Eylem TOPBAŞ

2016-01-01

Full Text Available Aim: This study has been designed to develop an assessment tool to be used in determining the patients’ satisfaction level with the peritoneal equilibration test (PET procedure. Materials and Methods: The development and validation of the peritoneal equilibration test Satisfaction Scale (PETSS was completed in two phases. Phase I focused on instrument construction and included item development and establishment of concurrent validity. Phase II included the factor analysis and psychometric assessment of the scale. In statistical evaluation of the data descriptive statistics and non-paratmetric tests were used. Results: The first version of the scale that has 3.62 Content Validity Index value was composed of 20 items. It was found that the latest version of the scale that has 14 items explained 46% of the variance. It was found that the Cronbach alfa value of this scale, which has 0.52-0.89 coefficient of item-total correlation was 0.96. Psychometric assessment of the scale revealed that except for type of the PET application, none of the demographic and clinical characteristics effect patients level of satisfaction during the PET application. Conclusion: This preliminary study showed that PETSS was a valid and reliable scale that can be used for determining satisfaction level of patients during PET application.

Robustness study in SSNTD method validation: indoor radon quality

Energy Technology Data Exchange (ETDEWEB)

Dias, D.C.S.; Silva, N.C.; Bonifácio, R.L., E-mail: danilacdias@gmail.com [Comissao Nacional de Energia Nuclear (LAPOC/CNEN), Pocos de Caldas, MG (Brazil). Laboratorio de Pocos de Caldas

2017-07-01

Quality control practices are indispensable to organizations aiming to reach analytical excellence. Method validation is an essential component to quality systems in laboratories, serving as a powerful tool for standardization and reliability of outcomes. This paper presents a study of robustness conducted over a SSNTD technique validation process, with the goal of developing indoor radon measurements at the highest level of quality. This quality parameter indicates how well a technique is able to provide reliable results in face of unexpected variations along the measurement. In this robustness study, based on the Youden method, 7 analytical conditions pertaining to different phases of the SSNTD technique (with focus on detector etching) were selected. Based on the ideal values for each condition as reference, extreme levels regarded as high and low were prescribed to each condition. A partial factorial design of 8 unique etching procedures was defined, where each presented their own set of high and low condition values. The Youden test provided 8 indoor radon concentration results, which allowed percentage estimations that indicate the potential influence of each analytical condition on the SSNTD technique. As expected, detector etching factors such as etching solution concentration, temperature and immersion time were identified as the most critical parameters to the technique. Detector etching is a critical step in the SSNTD method – one that must be carefully designed during validation and meticulously controlled throughout the entire process. (author)

Robustness study in SSNTD method validation: indoor radon quality

International Nuclear Information System (INIS)

Dias, D.C.S.; Silva, N.C.; Bonifácio, R.L.

2017-01-01

Quality control practices are indispensable to organizations aiming to reach analytical excellence. Method validation is an essential component to quality systems in laboratories, serving as a powerful tool for standardization and reliability of outcomes. This paper presents a study of robustness conducted over a SSNTD technique validation process, with the goal of developing indoor radon measurements at the highest level of quality. This quality parameter indicates how well a technique is able to provide reliable results in face of unexpected variations along the measurement. In this robustness study, based on the Youden method, 7 analytical conditions pertaining to different phases of the SSNTD technique (with focus on detector etching) were selected. Based on the ideal values for each condition as reference, extreme levels regarded as high and low were prescribed to each condition. A partial factorial design of 8 unique etching procedures was defined, where each presented their own set of high and low condition values. The Youden test provided 8 indoor radon concentration results, which allowed percentage estimations that indicate the potential influence of each analytical condition on the SSNTD technique. As expected, detector etching factors such as etching solution concentration, temperature and immersion time were identified as the most critical parameters to the technique. Detector etching is a critical step in the SSNTD method – one that must be carefully designed during validation and meticulously controlled throughout the entire process. (author)

OC5 Project Phase II: Validation of Global Loads of the DeepCwind Floating Semisubmersible Wind Turbine

DEFF Research Database (Denmark)

Robertson, Amy N.; Wendt, Fabian; Jonkman, Jason M.

2017-01-01

This paper summarizes the findings from Phase II of the Offshore Code Comparison, Collaboration, Continued, with Correlation project. The project is run under the International Energy Agency Wind Research Task 30, and is focused on validating the tools used for modeling offshore wind systems thro...

Validation of WIMS-AECL/(MULTICELL)/RFSP system by the results of phase-B test at Wolsung-II unit

Energy Technology Data Exchange (ETDEWEB)

Hong, In Seob; Min, Byung Joo; Suk, Ho Chun [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-03-01

The object of this study is the validation of WIMS-AECL lattice code which has been proposed for the substitution of POWDERPUFS-V(PPV) code. For the validation of this code, WIMS-AECL/(MULTICELL)/RFSP (lattice calculation/(incremental cross section calculation)/core calculation) code system has been used for the Post-Simulation of Phase-B physics Test at Wolsung-II unit. This code system had been used for the Wolsong-I and Point Lepraeu reactors, but after a few modifications of WIMS-AECL input values for Wolsong-II, the results of WIMS-AECL/RFSP code calculations are much improved to those of the old ones. Most of the results show good estimation except moderator temperature coefficient test. And the verification of this result must be done, which is one of the further work. 6 figs., 15 tabs. (Author)

Parent Reports of Young Spanish-English Bilingual Children's Productive Vocabulary: A Development and Validation Study

Science.gov (United States)

Mancilla-Martinez, Jeannette; Gámez, Perla B.; Vagh, Shaher Banu; Lesaux, Nonie K.

2016-01-01

Purpose: This 2-phase study aims to extend research on parent report measures of children's productive vocabulary by investigating the development (n = 38) of the Spanish Vocabulary Extension and validity (n = 194) of the 100-item Spanish and English MacArthur-Bates Communicative Development Inventories Toddler Short Forms and Upward Extension…

Design description and validation results for the IFMIF High Flux Test Module as outcome of the EVEDA phase

Directory of Open Access Journals (Sweden)

F. Arbeiter

2016-12-01

Full Text Available During the Engineering Validation and Engineering Design Activities (EVEDA phase (2007-2014 of the International Fusion Materials Irradiation Facility (IFMIF, an advanced engineering design of the High Flux Test Module (HFTM has been developed with the objective to facilitate the controlled irradiation of steel samples in the high flux area directly behind the IFMIF neutron source. The development process addressed included manufacturing techniques, CAD, neutronic, thermal-hydraulic and mechanical analyses complemented by a series of validation activities. Validation included manufacturing of 1:1 parts and mockups, test of prototypes in the FLEX and HELOKA-LP helium loops of KIT for verification of the thermal and mechanical properties, and irradiation of specimen filled capsule prototypes in the BR2 test reactor. The prototyping activities were backed by several R&D studies addressing focused issues like handling of liquid NaK (as filling medium and insertion of Small Specimen Test Technique (SSTT specimens into the irradiation capsules. This paper provides an up-todate design description of the HFTM irradiation device, and reports on the achieved performance criteria related to the requirements. Results of the validation activities are accounted for and the most important issues for further development are identified.

Development and Validation of Multi-Dimensional Personality ...

African Journals Online (AJOL)

This study was carried out to establish the scientific processes for the development and validation of Multi-dimensional Personality Inventory (MPI). The process of development and validation occurred in three phases with five components of Agreeableness, Conscientiousness, Emotional stability, Extroversion, and ...

Development and Validation of a Risk Scale for Emergence Agitation After General Anesthesia in Children: A Prospective Observational Study.

Science.gov (United States)

Hino, Maai; Mihara, Takahiro; Miyazaki, Saeko; Hijikata, Toshiyuki; Miwa, Takaaki; Goto, Takahisa; Ka, Koui

2017-08-01

Emergence agitation (EA) is a common complication in children after general anesthesia. The goal of this 2-phase study was (1) to develop a predictive model (EA risk scale) for the incidence of EA in children receiving sevoflurane anesthesia by performing a retrospective analysis of data from our previous study (phase 1) and (2) to determine the validity of the EA risk scale in a prospective observational cohort study (phase 2). Using data collected from 120 patients in our previous study, logistic regression analysis was used to predict the incidence of EA in phase 1. The optimal combination of the predictors was determined by a stepwise selection procedure using Akaike information criterion. The β-coefficient for the selected predictors was calculated, and scores for predictors determined. The predictive ability of the EA risk scale was assessed by a receiver operating characteristic (ROC) curve, and the area under the ROC curve (c-index) was calculated with a 95% confidence interval (CI). In phase 2, the validity of the EA risk scale was confirmed using another data set of 100 patients (who underwent minor surgery under general anesthesia). The ROC curve, the c-index, the best cutoff point, and the sensitivity and specificity at the point were calculated. In addition, we calculated the gray zone, which ranges between the two points where sensitivity and specificity, respectively, become 90%. In phase 1, the final model of the multivariable logistic regression analysis included the following 4 predictors: age (logarithm odds ratios [OR], -0.38; 95% CI, -0.81 to 0.00), Pediatric Anesthesia Behavior score (logarithm OR, 0.65; 95% CI, -0.09 to 1.40), anesthesia time (logarithm OR, 0.60; 95% CI, -0.18 to 1.19), and operative procedure (logarithm OR, 2.53; 95% CI, 1.30-3.75 for strabismus surgery and logarithm OR, 2.71; 95% CI, 0.99-4.45 for tonsillectomy). The EA risk scale included these 4 predictors and ranged from 1 to 23 points. In phase 2, the incidence of EA

Spiral computed tomography phase-space source model in the BEAMnrc/EGSnrc Monte Carlo system: implementation and validation

International Nuclear Information System (INIS)

Kim, Sangroh; Yoshizumi, Terry T; Yin Fangfang; Chetty, Indrin J

2013-01-01

Currently, the BEAMnrc/EGSnrc Monte Carlo (MC) system does not provide a spiral CT source model for the simulation of spiral CT scanning. We developed and validated a spiral CT phase-space source model in the BEAMnrc/EGSnrc system. The spiral phase-space source model was implemented in the DOSXYZnrc user code of the BEAMnrc/EGSnrc system by analyzing the geometry of spiral CT scan—scan range, initial angle, rotational direction, pitch, slice thickness, etc. Table movement was simulated by changing the coordinates of the isocenter as a function of beam angles. Some parameters such as pitch, slice thickness and translation per rotation were also incorporated into the model to make the new phase-space source model, designed specifically for spiral CT scan simulations. The source model was hard-coded by modifying the ‘ISource = 8: Phase-Space Source Incident from Multiple Directions’ in the srcxyznrc.mortran and dosxyznrc.mortran files in the DOSXYZnrc user code. In order to verify the implementation, spiral CT scans were simulated in a CT dose index phantom using the validated x-ray tube model of a commercial CT simulator for both the original multi-direction source (ISOURCE = 8) and the new phase-space source model in the DOSXYZnrc system. Then the acquired 2D and 3D dose distributions were analyzed with respect to the input parameters for various pitch values. In addition, surface-dose profiles were also measured for a patient CT scan protocol using radiochromic film and were compared with the MC simulations. The new phase-space source model was found to simulate the spiral CT scanning in a single simulation run accurately. It also produced the equivalent dose distribution of the ISOURCE = 8 model for the same CT scan parameters. The MC-simulated surface profiles were well matched to the film measurement overall within 10%. The new spiral CT phase-space source model was implemented in the BEAMnrc/EGSnrc system. This work will be beneficial in estimating the

Spiral computed tomography phase-space source model in the BEAMnrc/EGSnrc Monte Carlo system: implementation and validation.

Science.gov (United States)

Kim, Sangroh; Yoshizumi, Terry T; Yin, Fang-Fang; Chetty, Indrin J

2013-04-21

Currently, the BEAMnrc/EGSnrc Monte Carlo (MC) system does not provide a spiral CT source model for the simulation of spiral CT scanning. We developed and validated a spiral CT phase-space source model in the BEAMnrc/EGSnrc system. The spiral phase-space source model was implemented in the DOSXYZnrc user code of the BEAMnrc/EGSnrc system by analyzing the geometry of spiral CT scan-scan range, initial angle, rotational direction, pitch, slice thickness, etc. Table movement was simulated by changing the coordinates of the isocenter as a function of beam angles. Some parameters such as pitch, slice thickness and translation per rotation were also incorporated into the model to make the new phase-space source model, designed specifically for spiral CT scan simulations. The source model was hard-coded by modifying the 'ISource = 8: Phase-Space Source Incident from Multiple Directions' in the srcxyznrc.mortran and dosxyznrc.mortran files in the DOSXYZnrc user code. In order to verify the implementation, spiral CT scans were simulated in a CT dose index phantom using the validated x-ray tube model of a commercial CT simulator for both the original multi-direction source (ISOURCE = 8) and the new phase-space source model in the DOSXYZnrc system. Then the acquired 2D and 3D dose distributions were analyzed with respect to the input parameters for various pitch values. In addition, surface-dose profiles were also measured for a patient CT scan protocol using radiochromic film and were compared with the MC simulations. The new phase-space source model was found to simulate the spiral CT scanning in a single simulation run accurately. It also produced the equivalent dose distribution of the ISOURCE = 8 model for the same CT scan parameters. The MC-simulated surface profiles were well matched to the film measurement overall within 10%. The new spiral CT phase-space source model was implemented in the BEAMnrc/EGSnrc system. This work will be beneficial in estimating the spiral

Verification, validation and application of NEPTUNE-CFD to two-phase Pressurized Thermal Shocks

Energy Technology Data Exchange (ETDEWEB)

Mérigoux, N., E-mail: nicolas.merigoux@edf.fr [Electricité de France, R& D Division, 6 Quai Watier, 78401 Chatou (France); Laviéville, J.; Mimouni, S.; Guingo, M.; Baudry, C. [Electricité de France, R& D Division, 6 Quai Watier, 78401 Chatou (France); Bellet, S., E-mail: serge.bellet@edf.fr [Electricité de France, Thermal & Nuclear Studies and Projects Division, 12-14 Avenue Dutriévoz, 69628 Villeurbanne (France)

2017-02-15

Nuclear Power Plants are subjected to a variety of ageing mechanisms and, at the same time, exposed to potential Pressurized Thermal Shock (PTS) – characterized by a rapid cooling of the Reactor Pressure Vessel (RPV) wall. In this context, NEPTUNE-CFD is developed and used to model two-phase PTS in an industrial configuration, providing temperature and pressure fields required to assess the integrity of the RPV. Furthermore, when using CFD for nuclear safety demonstration purposes, EDF applies a methodology based on physical analysis, verification, validation and application to industrial scale (V&V), to demonstrate the quality of, and the confidence in results obtained. By following this methodology, each step must be proved to be consistent with the others, and with the final goal of the calculations. To this effect, a chart demonstrating how far the validation step of NEPTUNE-CFD is covering the PTS application will be drawn. A selection of the code verification and validation cases against different experiments will be described. For results consistency, a single and mature set of models – resulting from the knowledge acquired during the code development over the last decade – has been used. From these development and validation feedbacks, a methodology has been set up to perform industrial computations. Finally, the guidelines of this methodology based on NEPTUNE-CFD and SYRTHES coupling – to take into account the conjugate heat transfer between liquid and solid – will be presented. A short overview of the engineering approach will be given – starting from the meshing process, up to the results post-treatment and analysis.

Rapid Development and Validation of Improved Reversed-Phase High-performance Liquid Chromatography Method for the Quantification of Mangiferin, a Polyphenol Xanthone Glycoside in Mangifera indica.

Science.gov (United States)

Naveen, P; Lingaraju, H B; Prasad, K Shyam

2017-01-01

Mangiferin, a polyphenolic xanthone glycoside from Mangifera indica , is used as traditional medicine for the treatment of numerous diseases. The present study was aimed to develop and validate a reversed-phase high-performance liquid chromatography (RP-HPLC) method for the quantification of mangiferin from the bark extract of M. indica . RP-HPLC analysis was performed by isocratic elution with a low-pressure gradient using 0.1% formic acid: acetonitrile (87:13) as a mobile phase with a flow rate of 1.5 ml/min. The separation was done at 26°C using a Kinetex XB-C18 column as stationary phase and the detection wavelength at 256 nm. The proposed method was validated for linearity, precision, accuracy, limit of detection, limit of quantification, and robustness by the International Conference on Harmonisation guidelines. In linearity, the excellent correlation coefficient more than 0.999 indicated good fitting of the curve and also good linearity. The intra- and inter-day precision showed high reliability and reproducibility of the method. The recovery values at three different levels (50%, 100%, and 150%) of spiked samples were found to be 100.47, 100.89, and 100.99, respectively, and low standard deviation value high accuracy of the method. In robustness, the results remain unaffected by small variation in the analytical parameters, which shows the robustness of the method. Liquid chromatography-mass spectrometry analysis confirmed the presence of mangiferin with M/Z value of 421. The assay developed by HPLC method is a simple, rapid, and reliable for the determination of mangiferin from M. indica . The present study was intended to develop and validate an RP-HPLC method for the quantification of mangiferin from the bark extract of M. indica . The developed method was validated for linearity, precision, accuracy, limit of detection, limit of quantification and robustness by International Conference on Harmonization guidelines. This study proved that the developed

Quantification of construction waste prevented by BIM-based design validation: Case studies in South Korea.

Science.gov (United States)

Won, Jongsung; Cheng, Jack C P; Lee, Ghang

2016-03-01

Waste generated in construction and demolition processes comprised around 50% of the solid waste in South Korea in 2013. Many cases show that design validation based on building information modeling (BIM) is an effective means to reduce the amount of construction waste since construction waste is mainly generated due to improper design and unexpected changes in the design and construction phases. However, the amount of construction waste that could be avoided by adopting BIM-based design validation has been unknown. This paper aims to estimate the amount of construction waste prevented by a BIM-based design validation process based on the amount of construction waste that might be generated due to design errors. Two project cases in South Korea were studied in this paper, with 381 and 136 design errors detected, respectively during the BIM-based design validation. Each design error was categorized according to its cause and the likelihood of detection before construction. The case studies show that BIM-based design validation could prevent 4.3-15.2% of construction waste that might have been generated without using BIM. Copyright © 2015 Elsevier Ltd. All rights reserved.

NVN 5694 intra laboratory validation. Feasibility study for interlaboratory- validation

International Nuclear Information System (INIS)

Voors, P.I.; Baard, J.H.

1998-11-01

Within the project NORMSTAR 2 a number of Dutch prenormative protocols have been defined for radioactivity measurements. Some of these protocols, e.g. the Dutch prenormative protocol NVN 5694, titled Methods for radiochemical determination of polonium-210 and lead-210, have not been validated, neither by intralaboratory nor interlaboratory studies. Validation studies are conducted within the framework of the programme 'Normalisatie and Validatie van Milieumethoden 1993-1997' (Standardization and Validation of test methods for environmental parameters) of the Dutch Ministry of Housing, Physical Planning and the Environment (VROM). The aims of this study were (a) a critical evaluation of the protocol, (b) investigation on the feasibility of an interlaboratory study, and (c) the interlaboratory validation of NVN 5694. The evaluation of the protocol resulted in a list of deficiencies varying from missing references to incorrect formulae. From the survey by interview it appeared that for each type of material, there are 4 to 7 laboratories willing to participate in a interlaboratory validation study. This reflects the situation in 1997. Consequently, if 4 or 6 (the minimal number) laboratories are participating and each laboratory analyses 3 subsamples, the uncertainty in the repeatability standard deviation is 49 or 40 %, respectively. If the ratio of reproducibility standard deviation to the repeatability standard deviation is equal to 1 or 2, then the uncertainty in the reproducibility standard deviation increases from 42 to 67 % and from 34 to 52 % for 4 or 6 laboratories, respectively. The intralaboratory validation was established on four different types of materials. Three types of materials (milkpowder condensate and filter) were prepared in the laboratory using the raw material and certified Pb-210 solutions, and one (sediment) was obtained from the IAEA. The ECN-prepared reference materials were used after testing on homogeneity. The pre-normative protocol can

Two-phase CFD PTS validation in an extended range of thermohydraulics conditions covered by the COSI experiment

International Nuclear Information System (INIS)

Coste, P.; Ortolan, A.

2014-01-01

Highlights: • Models for large interfaces in two-phase CFD were developed for PTS. • The COSI experiment is used for NEPTUNE C FD integral validation. • COSI is a PWR cold leg scaled 1/100 for volume. • Fifty runs are calculated, covering a large range of flow configurations. • The CFD predicting capability is analysed using global and local measurements. - Abstract: In the context of the Pressurized Water Reactors (PWR) life duration safety studies, some models were developed to address the Pressurized Thermal Shock (PTS) from the two-phase CFD angle, dealing with interfaces much larger than cells size and with direct contact condensation. Such models were implemented in NEPTUNE C FD, a 3D transient Eulerian two-fluid model. The COSI experiment is used for its integral validation. It represents a cold leg scaled 1/100 for volume and power from a 900 MW PWR under a large range of LOCA PTS conditions. In this study, the CFD is evaluated in the whole range of parameters and flow configurations covered by the experiment. In a first step, a single choice of mesh and CFD models parameters is fixed and justified. In a second step, fifty runs are calculated. The CFD predicting capability is analysed, comparing the liquid temperature and the total condensation rate with the experiment, discussing their dependency on the inlet cold liquid rate, on the liquid level in the cold leg and on the difference between co-current and counter-current runs. It is shown that NEPTUNE C FD 1.0.8 calculates with a fair agreement a large range of flow configurations related to ECCS injection and steam condensation

Body Dysmorphic Symptoms Scale for patients seeking esthetic surgery: cross-cultural validation study.

Science.gov (United States)

Ramos, Tatiana Dalpasquale; Brito, Maria José Azevedo de; Piccolo, Mônica Sarto; Rosella, Maria Fernanda Normanha da Silva Martins; Sabino, Miguel; Ferreira, Lydia Masako

2016-01-01

Rhinoplasty is one of the most sought-after esthetic operations among individuals with body dysmorphic disorder. The aim of this study was to cross-culturally adapt and validate the Body Dysmorphic Symptoms Scale. Cross-cultural validation study conducted in a plastic surgery outpatient clinic of a public university hospital. Between February 2014 and March 2015, 80 consecutive patients of both sexes seeking rhinoplasty were selected. Thirty of them participated in the phase of cultural adaptation of the instrument. Reproducibility was tested on 20 patients and construct validity was assessed on 50 patients, with correlation against the Yale-Brown Obsessive Compulsive Scale for Body Dysmorphic Disorder. The Brazilian version of the instrument showed Cronbach's alpha of 0.805 and excellent inter-rater reproducibility (intraclass correlation coefficient, ICC = 0.873; P Dysmorphic Disorder and the Body Dysmorphic Symptoms Scale. The area under the receiver operating characteristic curve was 0.981, thus showing good accuracy for discriminating between presence and absence of symptoms of body dysmorphic disorder. Forty-six percent of the patients had body dysmorphic symptoms and 54% had moderate to severe appearance-related obsessive-compulsive symptoms. The Brazilian version of the Body Dysmorphic Symptoms Scale is a reproducible instrument that presents face, content and construct validity.

Design of a Competency Evaluation Model for Clinical Nursing Practicum, Based on Standardized Language Systems: Psychometric Validation Study.

Science.gov (United States)

Iglesias-Parra, Maria Rosa; García-Guerrero, Alfonso; García-Mayor, Silvia; Kaknani-Uttumchandani, Shakira; León-Campos, Álvaro; Morales-Asencio, José Miguel

2015-07-01

To develop an evaluation system of clinical competencies for the practicum of nursing students based on the Nursing Interventions Classification (NIC). Psychometric validation study: the first two phases addressed definition and content validation, and the third phase consisted of a cross-sectional study for analyzing reliability. The study population was undergraduate nursing students and clinical tutors. Through the Delphi technique, 26 competencies and 91 interventions were isolated. Cronbach's α was 0.96. Factor analysis yielded 18 factors that explained 68.82% of the variance. Overall inter-item correlation was 0.26, and total-item correlation ranged between 0.66 and 0.19. A competency system for the nursing practicum, structured on the NIC, is a reliable method for assessing and evaluating clinical competencies. Further evaluations in other contexts are needed. The availability of standardized language systems in the nursing discipline supposes an ideal framework to develop the nursing curricula. © 2015 Sigma Theta Tau International.

Study of a new static mixer for two-phase and single-phase flows

International Nuclear Information System (INIS)

Foucrier, Michel

1996-01-01

The subject of this work is the study of OptimiX, a new static mixer, which is fully designed using an inverse method taking the final product features as input and based on the physical properties of the fluid to mix. The work began with the construction of an experimental loop which allowed us to qualify the mixer in two-phase and single-phase flow conditions. Next, a chemical method using a new test reaction and a micro-mixing model have been used to further characterise the mixer. This test reaction and the micro-mixing model have been developed by the 'Laboratoire des Sciences du Genie Chimique' of Nancy. The mixer OptimiX has proved to be an excellent device for both macro- and micro-mixing. The capability of this mixer to foster rapid reactions was also demonstrated. The well organised flow pattern of OptimiX, which results from its design, provides it with the unusual feature of being fully calculable. This work emphasizes the internal hydrodynamics of this mixer, justifies the universality of the design procedures, which validation is supported by the completed qualification work. (author) [fr

Prediction of early death among patients enrolled in phase I trials: development and validation of a new model based on platelet count and albumin.

Science.gov (United States)

Ploquin, A; Olmos, D; Lacombe, D; A'Hern, R; Duhamel, A; Twelves, C; Marsoni, S; Morales-Barrera, R; Soria, J-C; Verweij, J; Voest, E E; Schöffski, P; Schellens, J H; Kramar, A; Kristeleit, R S; Arkenau, H-T; Kaye, S B; Penel, N

2012-09-25

Selecting patients with 'sufficient life expectancy' for Phase I oncology trials remains challenging. The Royal Marsden Hospital Score (RMS) previously identified high-risk patients as those with ≥ 2 of the following: albumin upper limit of normal; >2 metastatic sites. This study developed an alternative prognostic model, and compared its performance with that of the RMS. The primary end point was the 90-day mortality rate. The new model was developed from the same database as RMS, but it used Chi-squared Automatic Interaction Detection (CHAID). The ROC characteristics of both methods were then validated in an independent database of 324 patients enrolled in European Organization on Research and Treatment of Cancer Phase I trials of cytotoxic agents between 2000 and 2009. The CHAID method identified high-risk patients as those with albumin model and RMS, respectively. The negative predictive values (NPV) were similar for the CHAID model and RMS. The CHAID model and RMS provided a similarly high level of NPV, but the CHAID model gave a better accuracy in the validation set. Both CHAID model and RMS may improve the screening process in phase I trials.

Base Flow Model Validation, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The innovation is the systematic "building-block" validation of CFD/turbulence models employing a GUI driven CFD code (RPFM) and existing as well as new data sets to...

Development and validation of a numerical method for computing two-phase flows without interface reconstruction. Application to Taylor bubbles dynamics

International Nuclear Information System (INIS)

Benkenida, Adlene

1999-01-01

This work is devoted to the development and the use of a numerical code aimed to compute complex two-phase flows in which the topology of the interfaces evolves in time. The solution strategy makes use of a fixed grid on which interfaces evolve freely. The governing equations of the model (one-fluid model) are obtained by adding the local, instantaneous Navier-Stokes equations of each phase after a spatial filtering. The use of an Eulerian approach yields difficulties in estimating several of the two-phase quantities, especially the viscous stress tensor. This problem is overcome by deriving and validating an expression of the stress tensor valid for any Eulerian treatment and whatever the orientation of the interfaces with respect to the grid. To simplify the governing equations of the model, it is assumed that no phase change occurs, that no local slip exists between both phases, and that no small-scale turbulence is present. The possibility to remove some of these hypotheses is discussed, especially with the future aim of developing a large-eddy simulation approach of two-phase flows in which the motion and the effects of small-scale two-phase structures could be taken into account. Interface transport is performed by using a FCT front capturing method without any interface reconstruction procedure. It is shown through several tests that the version of Zalesak's (1979) algorithm in which each direction is treated independently yields the best results, even though a tendency for interfacial regions to thicken artificially is observed in regions with high stretching rates.The code is validated by performing simulations on some simple two-phase flows and by comparing numerical results with available analytical solutions, experiments, or previous computations. Among the results of these tests, those concerning the bouncing of a bubble on a rigid wall are the most original and shed new light on this phenomenon, especially by revealing the time evolution of the

Image quality validation of Sentinel 2 Level-1 products: performance status at the beginning of the constellation routine phase

Science.gov (United States)

Francesconi, Benjamin; Neveu-VanMalle, Marion; Espesset, Aude; Alhammoud, Bahjat; Bouzinac, Catherine; Clerc, Sébastien; Gascon, Ferran

2017-09-01

Sentinel-2 is an Earth Observation mission developed by the European Space Agency (ESA) in the frame of the Copernicus program of the European Commission. The mission is based on a constellation of 2-satellites: Sentinel-2A launched in June 2015 and Sentinel-2B launched in March 2017. It offers an unprecedented combination of systematic global coverage of land and coastal areas, a high revisit of five days at the equator and 2 days at mid-latitudes under the same viewing conditions, high spatial resolution, and a wide field of view for multispectral observations from 13 bands in the visible, near infrared and short wave infrared range of the electromagnetic spectrum. The mission performances are routinely and closely monitored by the S2 Mission Performance Centre (MPC), including a consortium of Expert Support Laboratories (ESL). This publication focuses on the Sentinel-2 Level-1 product quality validation activities performed by the MPC. It presents an up-to-date status of the Level-1 mission performances at the beginning of the constellation routine phase. Level-1 performance validations routinely performed cover Level-1 Radiometric Validation (Equalisation Validation, Absolute Radiometry Vicarious Validation, Absolute Radiometry Cross-Mission Validation, Multi-temporal Relative Radiometry Vicarious Validation and SNR Validation), and Level-1 Geometric Validation (Geolocation Uncertainty Validation, Multi-spectral Registration Uncertainty Validation and Multi-temporal Registration Uncertainty Validation). Overall, the Sentinel-2 mission is proving very successful in terms of product quality thereby fulfilling the promises of the Copernicus program.

Pre-Launch Phase 1 Calibration and Validation Rehearsal of Geophysical Data Products of Soil Moisture Active Passive (SMAP) Mission

Science.gov (United States)

Colliander, A.; Jackson, T. J.; Chan, S.; Dunbar, R.; Das, N. N.; Kim, S.; Reichle, R. H.; De Lannoy, G. J.; Liu, Q.; Kimball, J. S.; Yi, Y.; Cosh, M. H.; Bindlish, R.; Crow, W. T.; Dang, L.; Yueh, S. H.; Njoku, E. G.

2013-12-01

NASA's Soil Moisture Active Passive (SMAP) Mission is scheduled for launch in October 2014. The objective of the mission is global mapping of soil moisture and freeze/thaw state. SMAP utilizes an L-band radar and radiometer sharing a rotating 6-meter mesh reflector antenna. The instruments will operate onboard the SMAP spacecraft in a 685-km Sun-synchronous near-polar orbit, viewing the surface at a constant 40-degree incidence angle with a 1000-km swath width. Merging of active and passive L-band observations of the mission will enable an unprecedented combination of accuracy, resolution, coverage and revisit-time for soil moisture and freeze/thaw state retrieval. SMAP measurements will enable significantly improved estimates of water, energy and carbon transfers between the land and atmosphere. The SMAP science data product suite of geophysical parameters will include estimates of surface (top 5 cm) and root-zone (down to 1-m depth) soil moisture, net ecosystem exchange, and classification of the frozen/non-frozen state of the landscape. The primary validation reference of the data products will be ground-based measurements. Other remote sensing and model-based products will be used as additional resources. The post-launch timeline of the mission requires that the geophysical data products are validated (with respect to the mission requirements) within 12 months after a 3-month in-orbit check-out phase. SMAP is taking several preparatory steps in order to meet this schedule. One of the main steps consists of running a rehearsal to exercise calibration and validation procedures planned for the Cal/Val Phase. The rehearsal is divided into two stages. Phase 1, which was conducted in June-August 2013, focused on validation methodologies for the geophysical data products. Phase 2, which will be conducted in May-June 2014, includes operational aspects including a fully functioning SMAP Science Data System. (Note that the rehearsals do not include an airborne field

Improving Escalation of Care: Development and Validation of the Quality of Information Transfer Tool.

Science.gov (United States)

Johnston, Maximilian J; Arora, Sonal; Pucher, Philip H; Reissis, Yannis; Hull, Louise; Huddy, Jeremy R; King, Dominic; Darzi, Ara

2016-03-01

To develop and provide validity and feasibility evidence for the QUality of Information Transfer (QUIT) tool. Prompt escalation of care in the setting of patient deterioration can prevent further harm. Escalation and information transfer skills are not currently measured in surgery. This study comprised 3 phases: the development (phase 1), validation (phase 2), and feasibility analysis (phase 3) of the QUIT tool. Phase 1 involved identification of core skills needed for successful escalation of care through literature review and 33 semistructured interviews with stakeholders. Phase 2 involved the generation of validity evidence for the tool using a simulated setting. Thirty surgeons assessed a deteriorating postoperative patient in a simulated ward and escalated their care to a senior colleague. The face and content validity were assessed using a survey. Construct and concurrent validity of the tool were determined by comparing performance scores using the QUIT tool with those measured using the Situation-Background-Assessment-Recommendation (SBAR) tool. Phase 3 was conducted using direct observation of escalation scenarios on surgical wards in 2 hospitals. A 7-category assessment tool was developed from phase 1 consisting of 24 items. Twenty-one of 24 items had excellent content validity (content validity index >0.8). All 7 categories and 18 of 24 (P validity. The correlation between the QUIT and SBAR tools used was strong indicating concurrent validity (r = 0.694, P information transfer skills than nurses when faced with a deteriorating patient. A validated tool to assess information transfer for deteriorating surgical patients was developed and tested using simulation and real-time clinical scenarios. It may improve the quality and safety of patient care on the surgical ward.

Experimental study of low-titre critical two-phase flows

International Nuclear Information System (INIS)

Seynhaeve, Jean-Marie

1980-02-01

This report for engineering graduation addresses the analysis of two-phase critical flows obtained by expansion of a saturated or under-cooled liquid. For a titre greater than 0,1, theoretical studies give a rather good prediction of critical flow rates, whereas in the case of a lower titre, results obtained by published studies display some discrepancies, and the test duct geometry and important unbalances between phases seem to be at the origin of these discrepancies. In order to study these origins of discrepancies, three test campaigns have been performed: on a test duct provided by the CENG, on two long tubes, and on holes. Thus, after a bibliographical study which outlines drawbacks of previous studies, the author proposes a detailed description of experimental installations (creation of critical flows, measurement chain, measurement processing, measurement device calibration, quality and precision). Experimental results are then systematically explored, and differences are explained. The author then addresses the theoretical aspect of the determination of critical flow rates by reviewing calculation models and by comparing their results with experimental results. The validity of each model is thus discussed. The author then proposes a calculation model which can be applied to critical flows developed in holes. This model is notably inspired by experimental conclusions and gives very satisfying practical results

Development and validation of a reversed phase liquid chromatographic method for analysis of oxytetracycline and related impurities.

Science.gov (United States)

Kahsay, Getu; Shraim, Fairouz; Villatte, Philippe; Rotger, Jacques; Cassus-Coussère, Céline; Van Schepdael, Ann; Hoogmartens, Jos; Adams, Erwin

2013-03-05

A simple, robust and fast high-performance liquid chromatographic method is described for the analysis of oxytetracycline and its related impurities. The principal peak and impurities are all baseline separated in 20 min using an Inertsil C₈ (150 mm × 4.6 mm, 5 μm) column kept at 50 °C. The mobile phase consists of a gradient mixture of mobile phases A (0.05% trifluoroacetic acid in water) and B (acetonitrile-methanol-tetrahydrofuran, 80:15:5, v/v/v) pumped at a flow rate of 1.3 ml/min. UV detection was performed at 254 nm. The developed method was validated for its robustness, sensitivity, precision and linearity in the range from limit of quantification (LOQ) to 120%. The limits of detection (LOD) and LOQ were found to be 0.08 μg/ml and 0.32 μg/ml, respectively. This method allows the separation of oxytetracycline from all known and 5 unknown impurities, which is better than previously reported in the literature. Moreover, the simple mobile phase composition devoid of non-volatile buffers made the method suitable to interface with mass spectrometry for further characterization of unknown impurities. The developed method has been applied for determination of related substances in oxytetracycline bulk samples available from four manufacturers. The validation results demonstrate that the method is reliable for quantification of oxytetracycline and its impurities. Copyright © 2012 Elsevier B.V. All rights reserved.

Phase-field modelling and synchrotron validation of phase transformations in martensitic dual-phase steel

International Nuclear Information System (INIS)

Thiessen, R.G.; Sietsma, J.; Palmer, T.A.; Elmer, J.W.; Richardson, I.M.

2007-01-01

A thermodynamically based method to describe the phase transformations during heating and cooling of martensitic dual-phase steel has been developed, and in situ synchrotron measurements of phase transformations have been undertaken to support the model experimentally. Nucleation routines are governed by a novel implementation of the classical nucleation theory in a general phase-field code. Physically-based expressions for the temperature-dependent interface mobility and the driving forces for transformation have also been constructed. Modelling of martensite was accomplished by assuming a carbon supersaturation of the body-centred-cubic ferrite lattice. The simulations predict kinetic aspects of the austenite formation during heating and ferrite formation upon cooling. Simulations of partial austenitising thermal cycles predicted peak and retained austenite percentages of 38.2% and 6.7%, respectively, while measurements yielded peak and retained austenite percentages of 31.0% and 7.2% (±1%). Simulations of a complete austenitisation thermal cycle predicted the measured complete austenitisation and, upon cooling, a retained austenite percentage of 10.3% while 9.8% (±1%) retained austenite was measured

Validation the quantification of beta emitters activity in urine by scintillation spectrometry in the liquid phase

International Nuclear Information System (INIS)

Sierra, I.; Hernandez, C.; Benito, P.; Lopez, C.

2013-01-01

In this paper the methodology used in the validation of the technique for quantifying activity of some beta emitters in urine ( 3 H, 1 4C, 3 5S, 3 2P and 9 0Sr) by scintillation spectrometry Liquid Phase (Liquid Scintillation Counting, LSC) is described in bio elimination Laboratory Service CIEMAT Radiation Dosimetry accredited since last year for carrying out assays measure radiation dose based on ISO forth above. (Author)

A rapid and validated HPLC method to quantify sphingosine 1-phosphate in human plasma using solid-phase extraction followed by derivatization with fluorescence detection

NARCIS (Netherlands)

Butter, Jan J.; Koopmans, Richard P.; Michel, Martin C.

2005-01-01

We describe the development and validation of analytical methodology for the determination of sphingosine 1-phosphate (S1P) in plasma. It uses solid-phase extraction (SPE) followed by an automated reversed-phase gradient HPLC column-switching system with a pre-column derivatization with

Results from the First Validation Phase of CAP code

International Nuclear Information System (INIS)

Choo, Yeon Joon; Hong, Soon Joon; Hwang, Su Hyun; Kim, Min Ki; Lee, Byung Chul; Ha, Sang Jun; Choi, Hoon

2010-01-01

The second stage of Safety Analysis Code Development for Nuclear Power Plants was lunched on Apirl, 2010 and is scheduled to be through 2012, of which the scope of work shall cover from code validation to licensing preparation. As a part of this project, CAP(Containment Analysis Package) will follow the same procedures. CAP's validation works are organized hieratically into four validation steps using; 1) Fundamental phenomena. 2) Principal phenomena (mixing and transport) and components in containment. 3) Demonstration test by small, middle, large facilities and International Standard Problems. 4) Comparison with other containment codes such as GOTHIC or COMTEMPT. In addition, collecting the experimental data related to containment phenomena and then constructing the database is one of the major works during the second stage as a part of this project. From the validation process of fundamental phenomenon, it could be expected that the current capability and the future improvements of CAP code will be revealed. For this purpose, simple but significant problems, which have the exact analytical solution, were selected and calculated for validation of fundamental phenomena. In this paper, some results of validation problems for the selected fundamental phenomena will be summarized and discussed briefly

Development and validation of a combined phased acoustical radiosity and image source model for predicting sound fields in rooms

DEFF Research Database (Denmark)

Marbjerg, Gerd Høy; Brunskog, Jonas; Jeong, Cheol-Ho

2015-01-01

A model, combining acoustical radiosity and the image source method, including phase shifts on reflection, has been developed. The model is denoted Phased Acoustical Radiosity and Image Source Method (PARISM), and it has been developed in order to be able to model both specular and diffuse...... radiosity by regarding the model as being stochastic. Three methods of implementation are proposed and investigated, and finally, recommendations are made for their use. Validation of the image source method is done by comparison with finite element simulations of a rectangular room with a porous absorber...

Validation studies of nursing diagnoses in neonatology

Directory of Open Access Journals (Sweden)

Pavlína Rabasová

2016-03-01

Full Text Available Aim: The objective of the review was the analysis of Czech and foreign literature sources and professional periodicals to obtain a relevant comprehensive overview of validation studies of nursing diagnoses in neonatology. Design: Review. Methods: The selection criterion was studies concerning the validation of nursing diagnoses in neonatology. To obtain data from relevant sources, the licensed professional databases EBSCO, Web of Science and Scopus were utilized. The search criteria were: date of publication - unlimited; academic periodicals - full text; peer-reviewed periodicals; search language - English, Czech and Slovak. Results: A total of 788 studies were found. Only 5 studies were eligible for content analysis, dealing specifically with validation of nursing diagnoses in neonatology. The analysis of the retrieved studies suggests that authors are most often concerned with identifying the defining characteristics of nursing diagnoses applicable to both the mother (parents and the newborn. The diagnoses were validated in the domains Role Relationship; Coping/Stress tolerance; Activity/Rest, and Elimination and Exchange. Diagnoses represented were from the field of dysfunctional physical needs as well as the field of psychosocial and spiritual needs. The diagnoses were as follows: Parental role conflict (00064; Impaired parenting (00056; Grieving (00136; Ineffective breathing pattern (00032; Impaired gas exchange (00030; and Impaired spontaneous ventilation (00033. Conclusion: Validation studies enable effective planning of interventions with measurable results and support clinical nursing practice.

The international INTRAVAL project. Phase 2, Summary report

International Nuclear Information System (INIS)

Larsson, A.; Pers, K.; Skagius, K.; Dverstorp, B.

1997-01-01

The international project INTRAVAL addresses the validation of models of transport of radionuclides through groundwater in the geosphere. Such models are used in the assessment of the long-term safety of radioactive waste disposal systems. The second phase of INTRAVAL, which started in 1990, was concluded at the end of 1993. The objective of Phase 2 was to increase the understanding how various geophysical, geohydrological and geochemical phenomena of importance for radionuclide transport from a repository to the biosphere could be described by mathematical models and to study the model validation process. Summarized results from Phase 2 of the INTRAVAL study are presented in this report. (K.A.)

Imaging phase holdup distribution of three phase flow systems using dual source gamma ray tomography

International Nuclear Information System (INIS)

Varma, Rajneesh; Al-Dahhan, Muthanna; O'Sullivan, Joseph

2008-01-01

Full text: Multiphase reaction and process systems are used in abundance in the chemical and biochemical industry. Tomography has been successfully employed to visualize the hydrodynamics of multiphase systems. Most of the tomography methods (gamma ray, x-ray and electrical capacitance and resistance) have been successfully implemented for two phase dynamic systems. However, a significant number of chemical and biochemical systems consists of dynamic three phases. Research effort directed towards the development of tomography techniques to image such dynamic system has met with partial successes for specific systems with applicability to limited operating conditions. A dual source tomography scanner has been developed that uses the 661 keV and 1332 keV photo peaks from the 137 Cs and 60 Co for imaging three phase systems. A new approach has been developed and applied that uses the polyenergetic Alternating Minimization (A-M) algorithm, developed by O'Sullivan and Benac (2007), for imaging the holdup distribution in three phases' dynamic systems. The new approach avoids the traditional post image processing approach used to determine the holdup distribution where the attenuation images of the mixed flow obtained from gamma ray photons of two different energies are used to determine the holdup of three phases. In this approach the holdup images are directly reconstructed from the gamma ray transmission data. The dual source gamma ray tomography scanner and the algorithm were validated using a three phase phantom. Based in the validation, three phase holdup studies we carried out in slurry bubble column containing gas liquid and solid phases in a dynamic state using the dual energy gamma ray tomography. The key results of the holdup distribution studies in the slurry bubble column along with the validation of the dual source gamma ray tomography system would be presented and discussed

Brazilian Portuguese Validated Version of the Cardiac Anxiety Questionnaire

International Nuclear Information System (INIS)

Sardinha, Aline; Nardi, Antonio Egidio; Araújo, Claudio Gil Soares de; Ferreira, Maria Cristina; Eifert, Georg H.

2013-01-01

Cardiac Anxiety (CA) is the fear of cardiac sensations, characterized by recurrent anxiety symptoms, in patients with or without cardiovascular disease. The Cardiac Anxiety Questionnaire (CAQ) is a tool to assess CA, already adapted but not validated to Portuguese. This paper presents the three phases of the validation studies of the Brazilian CAQ. To extract the factor structure and assess the reliability of the CAQ (phase 1), 98 patients with coronary artery disease were recruited. The aim of phase 2 was to explore the convergent and divergent validity. Fifty-six patients completed the CAQ, along with the Body Sensations Questionnaire (BSQ) and the Social Phobia Inventory (SPIN). To determine the discriminative validity (phase 3), we compared the CAQ scores of two subgroups formed with patients from phase 1 (n = 98), according to the diagnoses of panic disorder and agoraphobia, obtained with the MINI - Mini International Neuropsychiatric Interview. A 2-factor solution was the most interpretable (46.4% of the variance). Subscales were named 'Fear and Hypervigilance' (n = 9; alpha = 0.88), and 'Avoidance', (n = 5; alpha = 0.82). Significant correlation was found between factor 1 and the BSQ total score (p < 0.01), but not with factor 2. SPIN factors showed significant correlations with CAQ subscales (p < 0.01). In phase 3, 'Cardiac with panic' patients scored significantly higher in CAQ factor 1 (t = -3.42; p < 0.01, CI = -1.02 to -0.27), and higher, but not significantly different, in factor 2 (t = -1.98; p = 0.51, CI = -0.87 to 0.00). These results provide a definite Brazilian validated version of the CAQ, adequate to clinical and research settings

Brazilian Portuguese Validated Version of the Cardiac Anxiety Questionnaire

Energy Technology Data Exchange (ETDEWEB)

Sardinha, Aline, E-mail: alinesardinhapsi@gmail.com; Nardi, Antonio Egidio [Laboratório de Pânico e Respiração do Programa de Pós-Graduação em Psiquiatria e Saúde Mental do Instituto de Psiquiatria da Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro (Brazil); Instituto Nacional de Ciência e Tecnologia - Translational Medicine (INCT-TM, CNPq), Rio de Janeiro (Brazil); Araújo, Claudio Gil Soares de [Programa de Pós-Graduação em Ciências do Exercício e do Esporte da Universidade Gama Filho, Rio de Janeiro (Brazil); CLINIMEX - Clínica de Medicina do Exercício, Rio de Janeiro (Brazil); Ferreira, Maria Cristina [Programa de Pós-Graduação em Psicologia da Universidade Salgado de Oliveira, Rio de Janeiro (Brazil); Eifert, Georg H. [Schmid College of Science and Technology Psychology, Crean School of Health and Life Sciences -Chapman University (United States)

2013-12-15

Cardiac Anxiety (CA) is the fear of cardiac sensations, characterized by recurrent anxiety symptoms, in patients with or without cardiovascular disease. The Cardiac Anxiety Questionnaire (CAQ) is a tool to assess CA, already adapted but not validated to Portuguese. This paper presents the three phases of the validation studies of the Brazilian CAQ. To extract the factor structure and assess the reliability of the CAQ (phase 1), 98 patients with coronary artery disease were recruited. The aim of phase 2 was to explore the convergent and divergent validity. Fifty-six patients completed the CAQ, along with the Body Sensations Questionnaire (BSQ) and the Social Phobia Inventory (SPIN). To determine the discriminative validity (phase 3), we compared the CAQ scores of two subgroups formed with patients from phase 1 (n = 98), according to the diagnoses of panic disorder and agoraphobia, obtained with the MINI - Mini International Neuropsychiatric Interview. A 2-factor solution was the most interpretable (46.4% of the variance). Subscales were named 'Fear and Hypervigilance' (n = 9; alpha = 0.88), and 'Avoidance', (n = 5; alpha = 0.82). Significant correlation was found between factor 1 and the BSQ total score (p < 0.01), but not with factor 2. SPIN factors showed significant correlations with CAQ subscales (p < 0.01). In phase 3, 'Cardiac with panic' patients scored significantly higher in CAQ factor 1 (t = -3.42; p < 0.01, CI = -1.02 to -0.27), and higher, but not significantly different, in factor 2 (t = -1.98; p = 0.51, CI = -0.87 to 0.00). These results provide a definite Brazilian validated version of the CAQ, adequate to clinical and research settings.

Using wound care algorithms: a content validation study.

Science.gov (United States)

Beitz, J M; van Rijswijk, L

1999-09-01

Valid and reliable heuristic devices facilitating optimal wound care are lacking. The objectives of this study were to establish content validation data for a set of wound care algorithms, to identify their associated strengths and weaknesses, and to gain insight into the wound care decision-making process. Forty-four registered nurse wound care experts were surveyed and interviewed at national and regional educational meetings. Using a cross-sectional study design and an 83-item, 4-point Likert-type scale, this purposive sample was asked to quantify the degree of validity of the algorithms' decisions and components. Participants' comments were tape-recorded, transcribed, and themes were derived. On a scale of 1 to 4, the mean score of the entire instrument was 3.47 (SD +/- 0.87), the instrument's Content Validity Index was 0.86, and the individual Content Validity Index of 34 of 44 participants was > 0.8. Item scores were lower for those related to packing deep wounds (P valid and reliable definitions. The wound care algorithms studied proved valid. However, the lack of valid and reliable wound assessment and care definitions hinders optimal use of these instruments. Further research documenting their clinical use is warranted. Research-based practice recommendations should direct the development of future valid and reliable algorithms designed to help nurses provide optimal wound care.

Chiral chromatography studies of chemical behavior of cinacalcet on polysaccharide chiral reversed-phase HPLC stationary phases.

Science.gov (United States)

Dousa, Michal; Brichác, Jirí

2012-01-01

A rapid HPLC method for the analytical resolution of cinacalcet enantiomers was developed. Four chiral columns (two amylose and two cellulose type) were evaluated in RP systems. Excellent enantioseparation with a resolution of more than 6 was achieved on Chiralpak AY (amylose 5-chloro-2-methylphenylcarbamate chiral stationary phase) using 10 mM triethylamine (pH 8.0)-acetonitrile (40 + 60, v/v) mobile phase. Validation of the HPLC method, including linearity, LOD, LOQ, precision, accuracy, and selectivity, was performed according to the International Conference on Harmonization guidelines. The method was successfully applied for the determination of (S)-cinacalcet in enantiopure active pharmaceutical ingredient (R)-cinacalcet.

Phase 4 Studies in Heart Failure - What is Done and What is Needed?

Science.gov (United States)

Iyngkaran, Pupalan; Liew, Danny; McDonald, Peter; Thomas, Merlin C; Reid, Christopher; Chew, Derek; Hare, David L

Congestive heart failure (CHF) therapeutics is generated through a well-described evidence generating process. Phases 1 - 3 of this process are required prior to approval and widespread clinical use. Phase 3 in almost all cases is a methodologically sound randomized controlled trial (RCT). After this phase it is generally accepted that the treatment has a significant, independent and prognostically beneficial effect on the pathophysiological process. A major criticism of RCTs is the population to whom the result is applicable. When this population is significantly different from the trial cohort the external validity comes into question. Should the continuation of the evidence generating process continue these problems might be identified. Post marketing surveillance through phase 4 and comparative effectiveness studies through phase 5 trials are often underperformed in comparison to the RCT. These processes can help identify remote adverse events and define new hypotheses for community level benefits. This review is aimed at exploring the post-marketing scene for CHF therapeutics from an Australian health system perspective. We explore the phases of clinical trials, the level of evidence currently available and options for ensuring greater accountability for community level CHF clinical outcomes.

Review of Available Data for Validation of Nuresim Two-Phase CFD Software Applied to CHF Investigations

Directory of Open Access Journals (Sweden)

D. Bestion

2009-01-01

Full Text Available The NURESIM Project of the 6th European Framework Program initiated the development of a new-generation common European Standard Software Platform for nuclear reactor simulation. The thermal-hydraulic subproject aims at improving the understanding and the predictive capabilities of the simulation tools for key two-phase flow thermal-hydraulic processes such as the critical heat flux (CHF. As part of a multi-scale analysis of reactor thermal-hydraulics, a two-phase CFD tool is developed to allow zooming on local processes. Current industrial methods for CHF mainly use the sub-channel analysis and empirical CHF correlations based on large scale experiments having the real geometry of a reactor assembly. Two-phase CFD is used here for understanding some boiling flow processes, for helping new fuel assembly design, and for developing better CHF predictions in both PWR and BWR. This paper presents a review of experimental data which can be used for validation of the two-phase CFD application to CHF investigations. The phenomenology of DNB and Dry-Out are detailed identifying all basic flow processes which require a specific modeling in CFD tool. The resulting modeling program of work is given and the current state-of-the-art of the modeling within the NURESIM project is presented.

Validation of Malayalam Version of National Comprehensive Cancer Network Distress Thermometer and its Feasibility in Oncology Patients.

Science.gov (United States)

Biji, M S; Dessai, Sampada; Sindhu, N; Aravind, Sithara; Satheesan, B

2018-01-01

This study was designed to translate and validate the National Comprehensive Cancer Network (NCCN) distress thermometer (DT) in regional language " Malayalam" and to see the feasibility of using it in our patients. (1) To translate and validate the NCCN DT. (2) To study the feasibility of using validated Malayalam translated DT in Malabar Cancer center. This is a single-arm prospective observational study. The study was conducted at author's institution between December 8, 2015, and January 20, 2016 in the Department of Cancer Palliative Medicine. This was a prospective observational study carried out in two phases. In Phase 1, the linguistic validation of the NCCN DT was done. In Phase 2, the feasibility, face validity, and utility of the translated of NCCN DT in accordance with QQ-10 too was done. SPSS version 16 (SPSS Inc. Released 2007. SPSS for Windows, Version 16.0. Chicago, SPSS Inc.) was used for analysis. Ten patients were enrolled in Phase 2. The median age was 51.5 years and 40% of patients were male. All patients had completed at least basic education up to the primary level. The primary site of cancer was heterogeneous. The NCCN DT completion rate was 100%. The face validity, utility, reliability, and feasibility were 100%, 100%, 100%, and 90%, respectively. It can be concluded that the Malayalam validated DT has high face validity, utility, and it is feasible for its use.

Study of nanometer-level precise phase-shift system used in electronic speckle shearography and phase-shift pattern interferometry

Science.gov (United States)

Jing, Chao; Liu, Zhongling; Zhou, Ge; Zhang, Yimo

2011-11-01

The nanometer-level precise phase-shift system is designed to realize the phase-shift interferometry in electronic speckle shearography pattern interferometry. The PZT is used as driving component of phase-shift system and translation component of flexure hinge is developed to realize micro displacement of non-friction and non-clearance. Closed-loop control system is designed for high-precision micro displacement, in which embedded digital control system is developed for completing control algorithm and capacitive sensor is used as feedback part for measuring micro displacement in real time. Dynamic model and control model of the nanometer-level precise phase-shift system is analyzed, and high-precision micro displacement is realized with digital PID control algorithm on this basis. It is proved with experiments that the location precision of the precise phase-shift system to step signal of displacement is less than 2nm and the location precision to continuous signal of displacement is less than 5nm, which is satisfied with the request of the electronic speckle shearography and phase-shift pattern interferometry. The stripe images of four-step phase-shift interferometry and the final phase distributed image correlated with distortion of objects are listed in this paper to prove the validity of nanometer-level precise phase-shift system.

Brazilian Portuguese Validated Version of the Cardiac Anxiety Questionnaire

Science.gov (United States)

Sardinha, Aline; Nardi, Antonio Egidio; de Araújo, Claudio Gil Soares; Ferreira, Maria Cristina; Eifert, Georg H.

2013-01-01

Background Cardiac Anxiety (CA) is the fear of cardiac sensations, characterized by recurrent anxiety symptoms, in patients with or without cardiovascular disease. The Cardiac Anxiety Questionnaire (CAQ) is a tool to assess CA, already adapted but not validated to Portuguese. Objective This paper presents the three phases of the validation studies of the Brazilian CAQ. Methods To extract the factor structure and assess the reliability of the CAQ (phase 1), 98 patients with coronary artery disease were recruited. The aim of phase 2 was to explore the convergent and divergent validity. Fifty-six patients completed the CAQ, along with the Body Sensations Questionnaire (BSQ) and the Social Phobia Inventory (SPIN). To determine the discriminative validity (phase 3), we compared the CAQ scores of two subgroups formed with patients from phase 1 (n = 98), according to the diagnoses of panic disorder and agoraphobia, obtained with the MINI - Mini International Neuropsychiatric Interview. Results A 2-factor solution was the most interpretable (46.4% of the variance). Subscales were named "Fear and Hypervigilance" (n = 9; alpha = 0.88), and "Avoidance", (n = 5; alpha = 0.82). Significant correlation was found between factor 1 and the BSQ total score (p < 0.01), but not with factor 2. SPIN factors showed significant correlations with CAQ subscales (p < 0.01). In phase 3, "Cardiac with panic" patients scored significantly higher in CAQ factor 1 (t = -3.42; p < 0.01, CI = -1.02 to -0.27), and higher, but not significantly different, in factor 2 (t = -1.98; p = 0.51, CI = -0.87 to 0.00). Conclusions These results provide a definite Brazilian validated version of the CAQ, adequate to clinical and research settings. PMID:24145391

The international phase 4 validation study of the EORTC QLQ-SWB32: a stand-alone measure of spiritual wellbeing (SWB) for people receiving palliative care for cancer

OpenAIRE

Vivat, B.; Young, T.; Winstanley, J.; Arraras, J.; Black, K.; Boyle, F.; Brédart, A.; Costantini, A.; Guo, J.; Irarrazaval, M. E.; Kobayashi, K.; Kruizinga, R.; Navarro, M.; Omidvari, S.; Rohde, G. E.

2017-01-01

The EORTC Quality of Life (QL) Group has just completed the final phase (field-testing and validation) of an international project to develop a stand-alone measure of spiritual wellbeing (SWB) for palliative cancer patients. Participants (n= 451) - from 14 countries on four continents; 54% female; 188 Christian, 50 Muslim, 156 with no religion - completed a provisional 36-item measure of SWB plus the EORTC QLQ-C15-PAL (PAL), then took part in a structured debriefing interview. All items showe...

Validation of two-phase CFD models for propellant tank self-pressurization: Crossing fluid types, scales, and gravity levels

Science.gov (United States)

Kassemi, Mohammad; Kartuzova, Olga; Hylton, Sonya

2018-01-01

This paper examines our computational ability to capture the transport and phase change phenomena that govern cryogenic storage tank pressurization and underscores our strengths and weaknesses in this area in terms of three computational-experimental validation case studies. In the first study, 1g pressurization of a simulant low-boiling point fluid in a small scale transparent tank is considered in the context of the Zero-Boil-Off Tank (ZBOT) Experiment to showcase the relatively strong capability that we have developed in modelling the coupling between the convective transport and stratification in the bulk phases with the interfacial evaporative and condensing heat and mass transfer that ultimately control self-pressurization in the storage tank. Here, we show that computational predictions exhibit excellent temporal and spatial fidelity under the moderate Ra number - high Bo number convective-phase distribution regimes. In the second example, we focus on 1g pressurization and pressure control of the large-scale K-site liquid hydrogen tank experiment where we show that by crossing fluid types and physical scales, we enter into high Bo number - high Ra number flow regimes that challenge our ability to predict turbulent heat and mass transfer and their impact on the tank pressurization correctly, especially, in the vapor domain. In the final example, we examine pressurization results from the small scale simulant fluid Tank Pressure Control Experiment (TCPE) performed in microgravity to underscore the fact that in crossing into a low Ra number - low Bo number regime in microgravity, the temporal evolution of the phase front as affected by the time-dependent residual gravity and impulse accelerations becomes an important consideration. In this case detailed acceleration data are needed to predict the correct rate of tank self-pressurization.

Development and validation of reversed-phase HPLC gradient method for the estimation of efavirenz in plasma.

Directory of Open Access Journals (Sweden)

Shweta Gupta

Full Text Available Efavirenz is an anti-viral agent of non-nucleoside reverse transcriptase inhibitor category used as a part of highly active retroviral therapy for the treatment of infections of human immune deficiency virus type-1. A simple, sensitive and rapid reversed-phase high performance liquid chromatographic gradient method was developed and validated for the determination of efavirenz in plasma. The method was developed with high performance liquid chromatography using Waters X-Terra Shield, RP18 50 x 4.6 mm, 3.5 μm column and a mobile phase consisting of phosphate buffer pH 3.5 and Acetonitrile. The elute was monitored with the UV-Visible detector at 260 nm with a flow rate of 1.5 mL/min. Tenofovir disoproxil fumarate was used as internal standard. The method was validated for linearity, precision, accuracy, specificity, robustness and data obtained were statistically analyzed. Calibration curve was found to be linear over the concentration range of 1-300 μg/mL. The retention times of efavirenz and tenofovir disoproxil fumarate (internal standard were 5.941 min and 4.356 min respectively. The regression coefficient value was found to be 0.999. The limit of detection and the limit of quantification obtained were 0.03 and 0.1 μg/mL respectively. The developed HPLC method can be useful for quantitative pharmacokinetic parameters determination of efavirenz in plasma.

Validity of High School Physic Module With Character Values Using Process Skill Approach In STKIP PGRI West Sumatera

Science.gov (United States)

Anaperta, M.; Helendra, H.; Zulva, R.

2018-04-01

This study aims to describe the validity of physics module with Character Oriented Values Using Process Approach Skills at Dynamic Electrical Material in high school physics / MA and SMK. The type of research is development research. The module development model uses the development model proposed by Plomp which consists of (1) preliminary research phase, (2) the prototyping phase, and (3) assessment phase. In this research is done is initial investigation phase and designing. Data collecting technique to know validation is observation and questionnaire. In the initial investigative phase, curriculum analysis, student analysis, and concept analysis were conducted. In the design phase and the realization of module design for SMA / MA and SMK subjects in dynamic electrical materials. After that, the formative evaluation which include self evaluation, prototyping (expert reviews, one-to-one, and small group. At this stage validity is performed. This research data is obtained through the module validation sheet, which then generates a valid module.

Validation of malayalam version of national comprehensive cancer network distress thermometer and its feasibility in oncology patients

Directory of Open Access Journals (Sweden)

M S Biji

2018-01-01

Full Text Available Context: This study was designed to translate and validate the National Comprehensive Cancer Network (NCCN distress thermometer (DT in regional language " Malayalam" and to see the feasibility of using it in our patients. Aims: (1 To translate and validate the NCCN DT. (2 To study the feasibility of using validated Malayalam translated DT in Malabar Cancer center. Settings and Design: This is a single-arm prospective observational study. The study was conducted at author's institution between December 8, 2015, and January 20, 2016 in the Department of Cancer Palliative Medicine. Materials and Methods: This was a prospective observational study carried out in two phases. In Phase 1, the linguistic validation of the NCCN DT was done. In Phase 2, the feasibility, face validity, and utility of the translated of NCCN DT in accordance with QQ-10 too was done. Statistical Analysis Used: SPSS version 16 (SPSS Inc. Released 2007. SPSS for Windows, Version 16.0. Chicago, SPSS Inc. was used for analysis. Results: Ten patients were enrolled in Phase 2. The median age was 51.5 years and 40% of patients were male. All patients had completed at least basic education up to the primary level. The primary site of cancer was heterogeneous. The NCCN DT completion rate was 100%. The face validity, utility, reliability, and feasibility were 100%, 100%, 100%, and 90%, respectively. Conclusion: It can be concluded that the Malayalam validated DT has high face validity, utility, and it is feasible for its use.

Report of the Phase 1 of the Validation of the Fish Sexual Development Test for the Detection of Endocrine Active Substances

DEFF Research Database (Denmark)

Holbech, Henrik; Kinnberg, Karin Lund; Petersen, Gitte

This document presents the validation report (phase 1) of the Fish Sexual Development Test (FSDT). The FSDT covers a life-stage where sexual development is particularly sensitive to perturbation caused by endocrine active chemicals. The chemical exposure lasts for about 60 days, at the end of which...

Multi frequency phase fluorimetry (MFPF) for oxygen partial pressure measurement: ex vivo validation by polarographic clark-type electrode.

Science.gov (United States)

Boehme, Stefan; Duenges, Bastian; Klein, Klaus U; Hartwich, Volker; Mayr, Beate; Consiglio, Jolanda; Baumgardner, James E; Markstaller, Klaus; Basciani, Reto; Vogt, Andreas

2013-01-01

Measurement of partial pressure of oxygen (PO2) at high temporal resolution remains a technological challenge. This study introduces a novel PO2 sensing technology based on Multi-Frequency Phase Fluorimetry (MFPF). The aim was to validate MFPF against polarographic Clark-type electrode (CTE) PO2 measurements. MFPF technology was first investigated in N = 8 anaesthetised pigs at FIO2 of 0.21, 0.4, 0.6, 0.8 and 1.0. At each FIO2 level, blood samples were withdrawn and PO2 was measured in vitro with MFPF using two FOXY-AL300 probes immediately followed by CTE measurement. Secondly, MFPF-PO2 readings were compared to CTE in an artificial circulatory setup (human packed red blood cells, haematocrit of 30%). The impacts of temperature (20, 30, 40°C) and blood flow (0.8, 1.6, 2.4, 3.2, 4.0 L min(-1)) on MFPF-PO2 measurements were assessed. MFPF response time in the gas- and blood-phase was determined. Porcine MFPF-PO2 ranged from 63 to 749 mmHg; the corresponding CTE samples from 43 to 712 mmHg. Linear regression: CTE = 15.59+1.18*MFPF (R(2) = 0.93; P0.05). MFPF response-time (monoexponential) was 1.48±0.26 s for the gas-phase and 1.51±0.20 s for the blood-phase. MFPF-derived PO2 readings were reproducible and showed excellent correlation and good agreement with Clark-type electrode-based PO2 measurements. There was no relevant impact of temperature and blood flow upon MFPF-PO2 measurements. The response time of the MFPF FOXY-AL300 probe was adequate for real-time sensing in the blood phase.

Development and validation of reversed-phase high performance liquid chromatographic method for analysis of cephradine in human plasma samples

International Nuclear Information System (INIS)

Ahmad, M.; Usman, M.; Madni, A.; Akhtar, N.; Khalid, N.; Asghar, W.

2010-01-01

An HPLC method with high precision, accuracy and selectivity was developed and validated for the assessment of cephradine in human plasma samples. The extraction procedure was simple and accurate with single step followed by direct injection of sample into HPLC system. The extracted cephradine in spiked human plasma was separated and quantitated using reversed phase C/sub 18/ column and UV detection wavelength of 254 nm. The optimized mobile phase of new composition of 0.05 M potassium dihydrogen phosphate (pH 3.4)-acetonitrile (88: 12) was pumped at an optimum flow rate of 1 mL.min/sup 1/. The method resulted linearity in the concentration range 0.15- 20 micro g mL/sup -1/. The limit of detection (LOD) and limit of quantification (LOQ) were 0.05 and 0.150 Microg.mL/sup -1/, respectively. The accuracy of method was 98.68 %. This method can 1>e applied for bioequivalence studies and therapeutic drug monitoring as well as for the routine analysis of cephradine. (author)

Validation Methodology to Allow Simulated Peak Reduction and Energy Performance Analysis of Residential Building Envelope with Phase Change Materials: Preprint

Energy Technology Data Exchange (ETDEWEB)

Tabares-Velasco, P. C.; Christensen, C.; Bianchi, M.

2012-08-01

Phase change materials (PCM) represent a potential technology to reduce peak loads and HVAC energy consumption in residential buildings. This paper summarizes NREL efforts to obtain accurate energy simulations when PCMs are modeled in residential buildings: the overall methodology to verify and validate Conduction Finite Difference (CondFD) and PCM algorithms in EnergyPlus is presented in this study. It also shows preliminary results of three residential building enclosure technologies containing PCM: PCM-enhanced insulation, PCM impregnated drywall and thin PCM layers. The results are compared based on predicted peak reduction and energy savings using two algorithms in EnergyPlus: the PCM and Conduction Finite Difference (CondFD) algorithms.

The international phase 4 validation study of the EORTC QLQ-SWB32: A stand-alone measure of spiritual well-being for people receiving palliative care for cancer.

Science.gov (United States)

Vivat, B; Young, T E; Winstanley, J; Arraras, J I; Black, K; Boyle, F; Bredart, A; Costantini, A; Guo, J; Irarrazaval, M E; Kobayashi, K; Kruizinga, R; Navarro, M; Omidvari, S; Rohde, G E; Serpentini, S; Spry, N; Van Laarhoven, H W M; Yang, G M

2017-11-01

The EORTC Quality of Life Group has just completed the final phase (field-testing and validation) of an international project to develop a stand-alone measure of spiritual well-being (SWB) for palliative cancer patients. Participants (n = 451)-from 14 countries on four continents; 54% female; 188 Christian; 50 Muslim; 156 with no religion-completed a provisional 36-item measure of SWB plus the EORTC QLQ-C15-PAL (PAL), then took part in a structured debriefing interview. All items showed good score distribution across response categories. We assessed scale structure using principal component analysis and Rasch analysis, and explored construct validity, and convergent/divergent validity with the PAL. Twenty-two items in four scoring scales (Relationship with Self, Relationships with Others, Relationship with Someone or Something Greater, and Existential) explained 53% of the variance. The measure also includes a global SWB item and nine other items. Scores on the PAL global quality-of-life item and Emotional Functioning scale weakly-moderately correlated with scores on the global SWB item and two of the four SWB scales. This new validated 32-item SWB measure addresses a distinct aspect of quality-of-life, and is now available for use in research and clinical practice, with a role as both a measurement and an intervention tool. © 2017 John Wiley & Sons Ltd.

Experimental validation of a numerical model of two-phase displacement in porous medium

International Nuclear Information System (INIS)

Genty, A.

1996-01-01

Burial in geological layers appears to be an interesting solution to dispose of radioactive wastes. This thesis analyzes and simulates the behaviour of gas produced by waste barrels corrosion. The released contaminated gas drains the water initially present in the host rock and yields a water-gas two phase flow. A literature survey of two phase flow shows that fluid interfaces may display instabilities for definite flow characteristics. When the displacement is stable a smooth interface proceeds through the porous medium. When the interface shows fingering, the displacement is said to be 'viscous-unstable', and when the front is jagged the displacement is called 'capillary' displacement. A dimensional analysis of classical equations governing two phase flow in porous media is combined with a classification of dominant forces to define an original map of flow regimes that includes gravitational forces. The map is based on three dimensionless numbers and predicts a priori the flow type. For typical data describing a radioactive waste repository a 'viscous-unstable' displacement is predicted by the map. We simulate water-gas displacement with a numerical model previously developed; this code, based on the Muskat model, uses the mixed-hybrid finite elements technique and is therefore well adapted for tracking moving interfaces. Fluxes are well conserved, however instabilities cannot be simulated. We assume that there is always a scale to be found where instabilities can be averaged and we try to validate the model with experimental two phase flows. We performed laboratory water-gas flow experiments for a variety of flow conditions. The observed displacement types are consistent with the map of flow regimes. Good agreement with numerical simulations is obtained when precise parameters of the displacements are available, in particular relative permeability curves. We conclude that our model allows a first approach of migration of gas near a radioactive waste repository

Body Dysmorphic Symptoms Scale for patients seeking esthetic surgery: cross-cultural validation study

Directory of Open Access Journals (Sweden)

Tatiana Dalpasquale Ramos

Full Text Available ABSTRACT: CONTEXT AND OBJECTIVE: Rhinoplasty is one of the most sought-after esthetic operations among individuals with body dysmorphic disorder. The aim of this study was to cross-culturally adapt and validate the Body Dysmorphic Symptoms Scale. DESIGN AND SETTING: Cross-cultural validation study conducted in a plastic surgery outpatient clinic of a public university hospital. METHODS: Between February 2014 and March 2015, 80 consecutive patients of both sexes seeking rhinoplasty were selected. Thirty of them participated in the phase of cultural adaptation of the instrument. Reproducibility was tested on 20 patients and construct validity was assessed on 50 patients, with correlation against the Yale-Brown Obsessive Compulsive Scale for Body Dysmorphic Disorder. RESULTS: The Brazilian version of the instrument showed Cronbach's alpha of 0.805 and excellent inter-rater reproducibility (intraclass correlation coefficient, ICC = 0.873; P < 0.001 and intra-rater reproducibility (ICC = 0.939; P < 0.001. Significant differences in total scores were found between patients with and without symptoms (P < 0.001. A strong correlation (r = 0.841; P < 0.001 was observed between the Yale-Brown Obsessive Compulsive Scale for Body Dysmorphic Disorder and the Body Dysmorphic Symptoms Scale. The area under the receiver operating characteristic curve was 0.981, thus showing good accuracy for discriminating between presence and absence of symptoms of body dysmorphic disorder. Forty-six percent of the patients had body dysmorphic symptoms and 54% had moderate to severe appearance-related obsessive-compulsive symptoms. CONCLUSIONS: The Brazilian version of the Body Dysmorphic Symptoms Scale is a reproducible instrument that presents face, content and construct validity.

Development and validation of health related quality of life questionnaire (Indian scenario) in diabetic foot ulcer patients.

Science.gov (United States)

Kateel, Ramya; Augustine, Alfred J; Ullal, Sheetal; Prabhu, Shivananda; Bhat, Rahul; Adhikari, Prabha

2017-12-01

To develop and validate Health Related Quality of Life Questionnaire in Diabetic Foot Ulcer Patients (HRQLQDFU) for Indian scenario. This study was conducted in two phases. First phase was Development of HRQLQDFU which included literature search and expert interview. Second phase was validation of HRQLQDFL which included face validation, content validation and construct validation. Face validation was done by ten diabetic foot ulcer patients, ten practicing nurses and ten care givers. They were asked to read and respond to questionnaire and report any difficulty in understanding the questions. Further they were asked to add any item to the questionnaire which according to them has a significant effect on quality of life. Content validation was done by six subject experts who judged the content relevance of questionnaire with score ranging from zero to four; zero being least relevant and four being most relevant. Content validity index was calculated for each question. Questions having content validity index≥0.8 were selected for the study. Reliability was tested by calculating Cronbach's alpha. In the development phase a questionnaire containing 37 questions with six domains was developed. None of patient had difficulty in understanding questions. After content validation a new questionnaire containing 20 questions was developed. Cronbach's alpha was 0.86 which shows good reliability. The new health related quality of life questionnaire on diabetic foot ulcer patients for an Indian scenario is validated and can be a reliably measure for quality of life in diabetic foot ulcer patients. Copyright © 2017 Diabetes India. Published by Elsevier Ltd. All rights reserved.

Strengthening validity in studies of pelvic floor disorders through qualitative research: an example from Ethiopia.

Science.gov (United States)

Blystad, Astrid; Rortveit, Guri; Gjerde, Janne Lillelid; Muleta, Mulu; Moland, Karen Marie

2018-05-01

This formative qualitative follow-up study addresses validity concerns in the Dabat Incontinence and Prolapse (DABINCOP) study, which aimed to determine the prevalence of pelvic floor disorders in north-west Ethiopia. A pilot study using a questionnaire validated by pelvic exam showed severe underreporting of clinically relevant pelvic organ prolapse (POP). The objective of the follow-up study was to explore the reasons behind the underreporting and to gather information to strengthen the sensitivity and local relevance of the questionnaire to be employed in the main study. A qualitative formative study nested within the DABINCOP study was carried out in rural and semiurban communities using an interpretive approach and in-depth qualitative interviews. Women (5) who had not self-reported POP in the pilot but were diagnosed with severe prolapse after pelvic examination, and health-care workers in the research team (7) were interviewed individually within 1 year of the pilot. Systematic text condensation was used in the analysis. The women explained that shame and fear of social exclusion, lack of trust in the study and data collectors, and lack of hope for cure prevented them from disclosing. The health-care workers reported weaknesses in the questionnaire and the research approach. Time pressure and competition among data collectors may have compromised women's motivation to disclose. The study indicates that qualitative research may fruitfully be employed in the formative phase of an epidemiological study on sensitive reproductive health problems to enhance local relevance of the tool and overall validity of the study.

Improving Focal Depth Estimates: Studies of Depth Phase Detection at Regional Distances

Science.gov (United States)

Stroujkova, A.; Reiter, D. T.; Shumway, R. H.

2006-12-01

The accurate estimation of the depth of small, regionally recorded events continues to be an important and difficult explosion monitoring research problem. Depth phases (free surface reflections) are the primary tool that seismologists use to constrain the depth of a seismic event. When depth phases from an event are detected, an accurate source depth is easily found by using the delay times of the depth phases relative to the P wave and a velocity profile near the source. Cepstral techniques, including cepstral F-statistics, represent a class of methods designed for the depth-phase detection and identification; however, they offer only a moderate level of success at epicentral distances less than 15°. This is due to complexities in the Pn coda, which can lead to numerous false detections in addition to the true phase detection. Therefore, cepstral methods cannot be used independently to reliably identify depth phases. Other evidence, such as apparent velocities, amplitudes and frequency content, must be used to confirm whether the phase is truly a depth phase. In this study we used a variety of array methods to estimate apparent phase velocities and arrival azimuths, including beam-forming, semblance analysis, MUltiple SIgnal Classification (MUSIC) (e.g., Schmidt, 1979), and cross-correlation (e.g., Cansi, 1995; Tibuleac and Herrin, 1997). To facilitate the processing and comparison of results, we developed a MATLAB-based processing tool, which allows application of all of these techniques (i.e., augmented cepstral processing) in a single environment. The main objective of this research was to combine the results of three focal-depth estimation techniques and their associated standard errors into a statistically valid unified depth estimate. The three techniques include: 1. Direct focal depth estimate from the depth-phase arrival times picked via augmented cepstral processing. 2. Hypocenter location from direct and surface-reflected arrivals observed on sparse

Kursk Operation Simulation and Validation Exercise - Phase II (KOSAVE II)

National Research Council Canada - National Science Library

Bauman, Walter

1998-01-01

... (KOSAVE) Study (KOSAVE II) documents, in this report a statistical record of the Kursk battle, as represented in the KDB, for use as both a standalone descriptive record for historians, and as a baseline for a subsequent Phase...

Field-scale multi-phase LNAPL remediation: Validating a new computational framework against sequential field pilot trials.

Science.gov (United States)

Sookhak Lari, Kaveh; Johnston, Colin D; Rayner, John L; Davis, Greg B

2018-03-05

Remediation of subsurface systems, including groundwater, soil and soil gas, contaminated with light non-aqueous phase liquids (LNAPLs) is challenging. Field-scale pilot trials of multi-phase remediation were undertaken at a site to determine the effectiveness of recovery options. Sequential LNAPL skimming and vacuum-enhanced skimming, with and without water table drawdown were trialled over 78days; in total extracting over 5m 3 of LNAPL. For the first time, a multi-component simulation framework (including the multi-phase multi-component code TMVOC-MP and processing codes) was developed and applied to simulate the broad range of multi-phase remediation and recovery methods used in the field trials. This framework was validated against the sequential pilot trials by comparing predicted and measured LNAPL mass removal rates and compositional changes. The framework was tested on both a Cray supercomputer and a cluster. Simulations mimicked trends in LNAPL recovery rates (from 0.14 to 3mL/s) across all remediation techniques each operating over periods of 4-14days over the 78day trial. The code also approximated order of magnitude compositional changes of hazardous chemical concentrations in extracted gas during vacuum-enhanced recovery. The verified framework enables longer term prediction of the effectiveness of remediation approaches allowing better determination of remediation endpoints and long-term risks. Copyright © 2017 Commonwealth Scientific and Industrial Research Organisation. Published by Elsevier B.V. All rights reserved.

Validity of a jump training apparatus using Wii Balance Board.

Science.gov (United States)

Yamamoto, Keizo; Matsuzawa, Mamoru

2013-05-01

The dynamic quantification of jump ability is useful for sports performance evaluation. We developed a force measurement system using the Wii Balance Board (WBB). This study was conducted to validate the system in comparison with a laboratory-grade force plate (FP). For a static validation, weights of 10-180kg were put progressively on the WBB put on the FP. The vertical component of the ground reaction force (vGRF) was measured using both devices and compared. For the dynamic validation, 10 subjects without lower limb pathology participated in the study and performed vertical jumping twice on the WBB on the FP. The range of analysis was set from the landing after the first jump to taking off of the second jump. The peak values during the landing phase and jumping phase were obtained and the force-time integral (force impulse) was measured. The relations of the values measured using each device were compared using Pearson's correlation coefficient test and Bland-Altman plots (BAP). Significant correlation (P<.01, r=.99) was found between the values of both devices in the static and the dynamic test. Examination of the BAP revealed a proportion error in the landing phase and showed no relation in the jumping phase between the difference and the mean in the dynamic test. The WBB detects the vGRF in the jumping phase with high precision. Copyright © 2012 Elsevier B.V. All rights reserved.

MRI-guided Therapeutic Ultrasound : In vitro Validation of a New MR Compatible, Phased Array, Contact Endorectal Ultrasound Transducer with Active Feedback Control of Temperature Evolution

Science.gov (United States)

Salomir, Rares; Rata, Mihaela; Lafon, Cyril; Melodelima, David; Chapelon, Jean-Yves; Mathias, Adrien; Cotton, François; Bonmartin, Alain; Cathignol, Dominique

2006-05-01

Contact application of high intensity ultrasound was demonstrated to be suitable for thermal ablation of sectorial tumours of the digestive duct. Experimental validation of a new MR compatible ultrasonic device is described here, dedicated to the minimal invasive therapy of localized colorectal cancer. This is a cylindrical 1D 64-element phased array transducer of 14 mm diameter and 25 mm height (Imasonic, France) allowing electronic rotation of the acoustic beam. Operating frequency ranges from 3.5 to 4.0 MHz and up to 5 effective electrical watts per element are available. A plane wave is reconstructed by simultaneous excitation of eigth adjacent elements with an appropriate phase law. Driving electronics operates outside the Faraday cage of the scanner and provides fast switching capabilities. Excellent passive and active compatibility with the MRI data acquisition has been demonstrated. In addition, feasibility of active temperature control has been demonstrated based on real-time data export out of the MR scanner and a PID feedback algorithm. Further studies will address the in-vivo validation and the integration of a miniature NMR coil for increased SNR in the near field.

The development of portable equipment to study physical and chemical phases in natural waters

International Nuclear Information System (INIS)

Breward, N.; Peachey, D.

1988-08-01

A direct and relatively non-invasive method of measuring the speciation of dissolved metals in groundwaters has been developed. The equipment relies on a series of columns containing DAEA cellulose, cation exchange resin and anion exchange resin to extract sequentially and respectively colloids, cationic and anionic species. Organic colloids are eluted from the DAEA cellulose with dilute caustic soda while the inorganic colloids (Fe/Al oxyhydroxide phase) are stripped with dilute mineral acid. A further advantage of this scheme is the ability to concentrate the phases by at least a factor of ten. Applications to the groundwaters of the natural analogue sites currently under study by BGS will offer a means of validating thermodynamic databases used in modelling speciation of radionuclides such as uranium and thorium. (author)

interThermalPhaseChangeFoam—A framework for two-phase flow simulations with thermally driven phase change

Directory of Open Access Journals (Sweden)

Mahdi Nabil

2016-01-01

Full Text Available The volume-of-fluid (VOF approach is a mature technique for simulating two-phase flows. However, VOF simulation of phase-change heat transfer is still in its infancy. Multiple closure formulations have been proposed in the literature, each suited to different applications. While these have enabled significant research advances, few implementations are publicly available, actively maintained, or inter-operable. Here, a VOF solver is presented (interThermalPhaseChangeFoam, which incorporates an extensible framework for phase-change heat transfer modeling, enabling simulation of diverse phenomena in a single environment. The solver employs object oriented OpenFOAM library features, including Run-Time-Type-Identification to enable rapid implementation and run-time selection of phase change and surface tension force models. The solver is packaged with multiple phase change and surface tension closure models, adapted and refined from earlier studies. This code has previously been applied to study wavy film condensation, Taylor flow evaporation, nucleate boiling, and dropwise condensation. Tutorial cases are provided for simulation of horizontal film condensation, smooth and wavy falling film condensation, nucleate boiling, and bubble condensation. Validation and grid sensitivity studies, interfacial transport models, effects of spurious currents from surface tension models, effects of artificial heat transfer due to numerical factors, and parallel scaling performance are described in detail in the Supplemental Material (see Appendix A. By incorporating the framework and demonstration cases into a single environment, users can rapidly apply the solver to study phase-change processes of interest.

interThermalPhaseChangeFoam-A framework for two-phase flow simulations with thermally driven phase change

Science.gov (United States)

Nabil, Mahdi; Rattner, Alexander S.

The volume-of-fluid (VOF) approach is a mature technique for simulating two-phase flows. However, VOF simulation of phase-change heat transfer is still in its infancy. Multiple closure formulations have been proposed in the literature, each suited to different applications. While these have enabled significant research advances, few implementations are publicly available, actively maintained, or inter-operable. Here, a VOF solver is presented (interThermalPhaseChangeFoam), which incorporates an extensible framework for phase-change heat transfer modeling, enabling simulation of diverse phenomena in a single environment. The solver employs object oriented OpenFOAM library features, including Run-Time-Type-Identification to enable rapid implementation and run-time selection of phase change and surface tension force models. The solver is packaged with multiple phase change and surface tension closure models, adapted and refined from earlier studies. This code has previously been applied to study wavy film condensation, Taylor flow evaporation, nucleate boiling, and dropwise condensation. Tutorial cases are provided for simulation of horizontal film condensation, smooth and wavy falling film condensation, nucleate boiling, and bubble condensation. Validation and grid sensitivity studies, interfacial transport models, effects of spurious currents from surface tension models, effects of artificial heat transfer due to numerical factors, and parallel scaling performance are described in detail in the Supplemental Material (see Appendix A). By incorporating the framework and demonstration cases into a single environment, users can rapidly apply the solver to study phase-change processes of interest.

Experimental investigation of stratified two-phase flows in the hot leg of a PWR for CFD validation

Energy Technology Data Exchange (ETDEWEB)

Vallee, Christophe; Lucas, Dirk [Helmholtz-Zentrum Dresden-Rossendorf (HZDR) e.V., Dresden (Germany). Inst. of Fluid Dynamics; Tomiyama, Akio [Kobe Univ. (Japan). Graduate School of Engineering; Murase, Michio [Institute of Nuclear Safety System Inc. (INSS), Fukui (Japan)

2012-07-01

Stratified two-phase flows were investigated in two different models of the hot leg of a pressurised water reactor (PWR) in order to provide experimental data for the development and validation of computational fluid dynamics (CFD) codes. Therefore, the local flow structure was visualised with a high-speed video camera. Moreover, one test section was designed with a rectangular cross-section to achieve optimum observation conditions. The phenomenon of counter-current flow limitation (CCFL) was investigated, which may affect the reflux condenser cooling mode in some accident scenarios. (orig.)

The Neck Disability Index-Russian Language Version (NDI-RU): A Study of Validity and Reliability.

Science.gov (United States)

Bakhtadze, Maxim A; Vernon, Howard; Zakharova, Olga B; Kuzminov, Kirill O; Bolotov, Dmitry A

2015-07-15

Cross-cultural adaptation and psychometric testing. To perform a validated Russian translation and then to evaluate the validity and reliability of the Russian language version of the Neck Disability Index (NDI-RU). Neck pain is highly prevalent and can greatly affect daily activity. The Neck Disability Index (NDI) is the most frequently used scale for self-rating of disability due to neck pain. Its translated versions are applied in many countries. However, the Russian language version of the NDI has not been developed yet. Cross-cultural adaptation of the NDI-RU was performed according to established guidelines. Then, the NDI-RU was evaluated for content validity, concurrent criterion validity, internal consistency, test-retest reliability, factor structure, and minimum detectable change. Two hundred thirty-two patients took part in the study in total: 109 in validity (39.5 ± 10 yr), 123 in reliability (38.4 ± 11 yr; 80 in the test-retest phase). A culturally valid translation was achieved. NDI-RU total scores were distributed normally. Floor/ceiling effects were absent. Good values of Cronbach α were obtained for each item (from 0.80 to 0.84) and for the total NDI-RU (0.83). A 2-factor solution was found for the NDI-RU. The average interitem correlation coefficient was 0.53. Intraclass correlation coefficients for test-retest reliability coefficients ranged from 0.65 to 0.92 for different items and 0.91 for the total NDI-RU. Moderate correlation (Spearman rs = 0.62; P Russian language version of the Neck Disability Index resulted in a valid, reliable instrument that can be used both in clinical practice and scientific investigations. 1.

The validity of the 4-Skills Scan: A double validation study.

Science.gov (United States)

van Kernebeek, W G; de Kroon, M L A; Savelsbergh, G J P; Toussaint, H M

2018-06-01

Adequate gross motor skills are an essential aspect of a child's healthy development. Where physical education (PE) is part of the primary school curriculum, a strong curriculum-based emphasis on evaluation and support of motor skill development in PE is apparent. Monitoring motor development is then a task for the PE teacher. In order to fulfil this task, teachers need adequate tools. The 4-Skills Scan is a quick and easily manageable gross motor skill instrument; however, its validity has never been assessed. Therefore, the purpose of this study is to assess the construct and concurrent validity of both 4-Skills Scans (version 2007 and version 2015). A total of 212 primary school children (6 - 12 years old), was requested to participate in both versions of the 4-Skills Scan. For assessing construct validity, children covered an obstacle course with video recordings for observation by an expert panel. For concurrent validity, a comparison was made with the MABC-2, by calculating Pearson correlations. Multivariable linear regression analyses were performed to determine the contribution of each subscale to the construct of gross motor skills, according to the MABC-2 and the expert panel. Correlations between the 4-Skills Scans and expert valuations were moderate, with coefficients of .47 (version 2007) and .46 (version 2015). Correlations between the 4-Skills Scans and the MABC-2 (gross) were moderate (.56) for version 2007 and high (.64) for version 2015. It is concluded that both versions of the 4-Skills Scans are satisfactory valid instruments for assessing gross motor skills during PE lessons. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Development and validation of a new knowledge, attitude, belief and practice questionnaire on leptospirosis in Malaysia.

Science.gov (United States)

Zahiruddin, Wan Mohd; Arifin, Wan Nor; Mohd-Nazri, Shafei; Sukeri, Surianti; Zawaha, Idris; Bakar, Rahman Abu; Hamat, Rukman Awang; Malina, Osman; Jamaludin, Tengku Zetty Maztura Tengku; Pathman, Arumugam; Mas-Harithulfadhli-Agus, Ab Rahman; Norazlin, Idris; Suhailah, Binti Samsudin; Saudi, Siti Nor Sakinah; Abdullah, Nurul Munirah; Nozmi, Noramira; Zainuddin, Abdul Wahab; Aziah, Daud

2018-03-07

In Malaysia, leptospirosis is considered an endemic disease, with sporadic outbreaks following rainy or flood seasons. The objective of this study was to develop and validate a new knowledge, attitude, belief and practice (KABP) questionnaire on leptospirosis for use in urban and rural populations in Malaysia. The questionnaire comprised development and validation stages. The development phase encompassed a literature review, expert panel review, focus-group testing, and evaluation. The validation phase consisted of exploratory and confirmatory parts to verify the psychometric properties of the questionnaire. A total of 214 and 759 participants were recruited from two Malaysian states, Kelantan and Selangor respectively, for the validation phase. The participants comprised urban and rural communities with a high reported incidence of leptospirosis. The knowledge section of the validation phase utilized item response theory (IRT) analysis. The attitude and belief sections utilized exploratory factor analysis (EFA) and confirmatory factor analysis (CFA). The development phase resulted in a questionnaire that included four main sections: knowledge, attitude, belief, and practice. In the exploratory phase, as shown by the IRT analysis of knowledge about leptospirosis, the difficulty and discrimination values of the items were acceptable, with the exception of two items. Based on the EFA, the psychometric properties of the attitude, belief, and practice sections were poor. Thus, these sections were revised, and no further factor analysis of the practice section was conducted. In the confirmatory stage, the difficulty and discrimination values of the items in the knowledge section remained within the acceptable range. The CFA of the attitude section resulted in a good-fitting two-factor model. The CFA of the belief section retained low number of items, although the analysis resulted in a good fit in the final three-factor model. Based on the IRT analysis and factor

Standardisation And Validation Study Of A New Study Skills ...

African Journals Online (AJOL)

Concerns have also been raised by various researchers about the latent constructs of existing western scales to assess study skills. The objective of this study was to develop, standardize and validate a culturally sensitive study skills questionnaire (SSQ). Methods: a stratified random sample of secondary school students (n ...

Development and validation of the brief esophageal dysphagia questionnaire.

Science.gov (United States)

Taft, T H; Riehl, M; Sodikoff, J B; Kahrilas, P J; Keefer, L; Doerfler, B; Pandolfino, J E

2016-12-01

Esophageal dysphagia is common in gastroenterology practice and has multiple etiologies. A complication for some patients with dysphagia is food impaction. A valid and reliable questionnaire to rapidly evaluate esophageal dysphagia and impaction symptoms can aid the gastroenterologist in gathering information to inform treatment approach and further evaluation, including endoscopy. 1638 patients participated over two study phases. 744 participants completed the Brief Esophageal Dysphagia Questionnaire (BEDQ) for phase 1; 869 completed the BEDQ, Visceral Sensitivity Index, Gastroesophageal Reflux Disease Questionnaire, and Hospital Anxiety and Depression Scale for phase 2. Demographic and clinical data were obtained via the electronic medical record. The BEDQ was evaluated for internal consistency, split-half reliability, ceiling and floor effects, and construct validity. The BEDQ demonstrated excellent internal consistency, reliability, and construct validity. The symptom frequency and severity scales scored above the standard acceptable cutoffs for reliability while the impaction subscale yielded poor internal consistency and split-half reliability; thus the impaction items were deemed qualifiers only and removed from the total score. No significant ceiling or floor effects were found with the exception of 1 item, and inter-item correlations fell within accepted ranges. Construct validity was supported by moderate yet significant correlations with other measures. The predictive ability of the BEDQ was small but significant. The BEDQ represents a rapid, reliable, and valid assessment tool for esophageal dysphagia with food impaction for clinical practice that differentiates between patients with major motor dysfunction and mechanical obstruction. © 2016 John Wiley & Sons Ltd.

2013 CEF RUN - PHASE 1 DATA ANALYSIS AND MODEL VALIDATION

Energy Technology Data Exchange (ETDEWEB)

Choi, A.

2014-05-08

{sub gas} in the CEF vapor space was close to that of the ½ scale SGM, whose data were taken as directly applicable to the DWPF melter and thus used to set all the parameters of the original model. Based on these results of the CEF Phase 1 off-gas and thermal data analyses, it is concluded that: (1) The thermal characteristics of the CEF vapor space are prototypic thanks to its prototypic design; and (2) The CEF off-gas data are scalable in terms of predicting the flammability potential of the DWPF melter off-gas. These results also show that the existing DWPF safety controls on the TOC and antifoam as a function of nitrate are conservative by the same order of magnitude shown by the Phase 1 data at T{sub gas} < ~350°C, since they were set at T{sub gas} = 294°C, which falls into the region of excessive conservatism for the current DWPF model in terms of predicting the TOC-to-H{sub 2} conversion. In order to remedy the overly-conservative antifoam decomposition scheme used in the current DWPF model, the data from two recent tests will be analyzed in detail in order to gain additional insights into the antifoam decomposition chemistry in the cold cap. The first test was run in a temperature-programmed furnace using both normal and spiked feeds with fresh antifoam under inert and slightly oxidizing vapor space conditions. Phase 2 of the CEF test was run with the baseline nitric-glycolic acid flowsheet feeds that contained the “processed antifoam” and those spiked with fresh antifoam in order to study the effects of antifoam concentration as well as processing history on its decomposition chemistry under actual melter conditions. The goal is to develop an improved antifoam decomposition model from the analysis of these test data and incorporate it into a new multistage cold cap model to be developed concurrently for the nitric-glycolic acid flowsheet feeds. These activities will be documented in the Phase 2 report. Finally, it is recommended that some of the

Analytical method validation for quality control and the study of the 50 mg Propylthiouracil stability

International Nuclear Information System (INIS)

Valdes Bendoyro, Maria Olga; Garcia Penna, Caridad Margarita; Fernandez, Juan Lugones; Garcia Borges, Lisandra; Martinez Espinosa, Vivian

2010-01-01

A high-performance liquid chromatography analytical method was developed and validated for the quality control and stability studies of 50 mg Propylthiouracil tablets. Method is based in active principle separation through a 100 RP-18 RP-18 (5 μm) (250 x 4 mm) Lichrospher chromatography with UV detection to 272 nm, using a mobile phase composed by a ungaseous mixture of a 0.025 M buffer solution-monobasic potassium phosphate to pH= 4,6 ad acetonitrile in a 80:20 ratio with a flux speed of 0,5 mL/min. Analytical method was linear, precise, specific and exact in the study concentrations interval

Developing the Polish Educational Needs Assessment Tool (Pol-ENAT) in rheumatoid arthritis and systemic sclerosis: a cross-cultural validation study using Rasch analysis.

Science.gov (United States)

Sierakowska, Matylda; Sierakowski, Stanisław; Sierakowska, Justyna; Horton, Mike; Ndosi, Mwidimi

2015-03-01

To undertake cross-cultural adaptation and validation of the educational needs assessment tool (ENAT) for use with people with rheumatoid arthritis (RA) and systemic sclerosis (SSc) in Poland. The study involved two main phases: (1) cross-cultural adaptation of the ENAT from English into Polish and (2) Cross-cultural validation of Polish Educational Needs Assessment Tool (Pol-ENAT). The first phase followed an established process of cross-cultural adaptation of self-report measures. The second phase involved completion of the Pol-ENAT by patients and subjecting the data to Rasch analysis to assess the construct validity, unidimensionality, internal consistency and cross-cultural invariance. An adequate conceptual equivalence was achieved following the adaptation process. The dataset for validation comprised a total of 278 patients, 237 (85.3 %) of which were female. In each disease group (145, RA and 133, SSc), the 7 domains of the Pol-ENAT were found to fit the Rasch model, X (2)(df) = 16.953(14), p = 0.259 and 8.132(14), p = 0.882 for RA and SSc, respectively. Internal consistency of the Pol-ENAT was high (patient separation index = 0.85 and 0.89 for SSc and RA, respectively), and unidimensionality was confirmed. Cross-cultural differential item functioning (DIF) was detected in some subscales, and DIF-adjusted conversion tables were calibrated to enable cross-cultural comparison of data between Poland and the UK. Using a standard process in cross-cultural adaptation, conceptual equivalence was achieved between the original (UK) ENAT and the adapted Pol-ENAT. Fit to the Rasch model, confirmed that the construct validity, unidimensionality and internal consistency of the ENAT have been preserved.

Social Studies Oriented Achievement Goal Scale (SOAGS: Validity and Reliability Study

Directory of Open Access Journals (Sweden)

Melehat GEZER

2016-12-01

Full Text Available This study aims to develop a valid and reliable instrument for measuring students' social studies achievement goal. The research was conducted on a study group consisted of 374 middle school students studying in the central district of Diyarbakır in 2014-2015 school year fall semester. Expert opinion was consulted with regard to the scale's content and face validity. Exploratory Factor Analysis (EFA and Confirmatory Factor Analysis (CFA were performed in order to measure the scale's construct validity. As a result of EFA, a 29-item and a six-factor structure model which explains 50.82% of the total variance was obtained. The emerging factors were called as a self-approach, task-approach, other-approach, task-avoidance, other-avoidance and self-avoidance respectively. The findings acquired CFA indicated that the 29-item and six-factor structure related to social studies oriented achievement goal scale have acceptable goodness of fit indices. The scale's reliability coefficients were calculated by means of internal consistency method. As a result of reliability analysis, it was determined that the reliability coefficients were within admissible limits. The finding of the item correlation and 27% of upper and lower group comparisons demonstrated that all of the items in the scale should remain. In light of these results, it could be argued that the scale is reliable and valid instrument and can be used in order to test students' social studies achievement goals.

Quality data validation: Comprehensive approach to environmental data validation

International Nuclear Information System (INIS)

Matejka, L.A. Jr.

1993-01-01

Environmental data validation consists of an assessment of three major areas: analytical method validation; field procedures and documentation review; evaluation of the level of achievement of data quality objectives based in part on PARCC parameters analysis and expected applications of data. A program utilizing matrix association of required levels of validation effort and analytical levels versus applications of this environmental data was developed in conjunction with DOE-ID guidance documents to implement actions under the Federal Facilities Agreement and Consent Order in effect at the Idaho National Engineering Laboratory. This was an effort to bring consistent quality to the INEL-wide Environmental Restoration Program and database in an efficient and cost-effective manner. This program, documenting all phases of the review process, is described here

Development and Validation of Chemistry Self-Efficacy Scale for College Students

Science.gov (United States)

Uzuntiryaki, Esen; Aydin, Yesim Capa

2009-01-01

This study described the process of developing and validating the College Chemistry Self-Efficacy Scale (CCSS) that can be used to assess college students' beliefs in their ability to perform essential tasks in chemistry. In the first phase, data collected from 363 college students provided evidence for the validity and reliability of the new…

Study of SmS properties in the low pressure phase (black phase)

International Nuclear Information System (INIS)

Bordier, G.

1986-01-01

SmS was studied for the transition from low pressure phase (black phase) to high pressure phase with an intermediate valence. But the study of the black phase is very rich. The variations of electron transport properties with pressure at low temperature show a semi-metal phase located, in the pressure-temperature diagram in the black phase for pressure over 4 kbars, corresponding to the phase B'of the doping-temperature diagram. Electron spin resonance shows a lack of sulfur and nearby this defect a samarium ion, magnetically coupled with the matrix, presents a divalent trivalent transition. Resonance lines are broadened with temperature. Conductivity relaxations occur at low pressure and low temperature by trapping a conduction electron, by magnetic exchange giving a bounded magnetic polaron. The relaxation time at null magnetic field is activated. An approximation of trapping barrier and critical field corresponding the maximum magnetoresistance is given by a model [fr

Solid-phase microextraction

DEFF Research Database (Denmark)

Nilsson, Torben

The objective of this study has been to develop new analytical methods using the rapid, simple and solvent-free extraction technique solid-phase microextraction (SPME) for the quantitative analysis of organic pollutants at trace level in drinking water and environmental samples. The dynamics...... of SPME were examined for halogenated and non-halogenated volatile hydrocarbons, and a standard method for their quantitative analysis in aqueous samples was developed and validated in inter-laboratory studies on the basis of reference material and in comparison with the traditional methods....... The influences of some possible interferences on the SPME process were examined, and new SPME probes were tested for the in situ monitoring of groundwater pollutants. Inter-laboratory studies were carried out also for the validation of SPME for the quantitative analysis of organochlorine, organonitrogen...

[Design and validation of a questionnaire for psychosocial nursing diagnosis in Primary Care].

Science.gov (United States)

Brito-Brito, Pedro Ruymán; Rodríguez-Álvarez, Cristobalina; Sierra-López, Antonio; Rodríguez-Gómez, José Ángel; Aguirre-Jaime, Armando

2012-01-01

To develop a valid, reliable and easy-to-use questionnaire for a psychosocial nursing diagnosis. The study was performed in two phases: first phase, questionnaire design and construction; second phase, validity and reliability tests. A bank of items was constructed using the NANDA classification as a theoretical framework. Each item was assigned a Likert scale or dichotomous response. The combination of responses to the items constituted the diagnostic rules to assign up to 28 labels. A group of experts carried out the validity test for content. Other validated scales were used as reference standards for the criterion validity tests. Forty-five nurses provided the questionnaire to the patients on three separate occasions over a period of three weeks, and the other validated scales only once to 188 randomly selected patients in Primary Care centres in Tenerife (Spain). Validity tests for construct confirmed the six dimensions of the questionnaire with 91% of total variance explained. Validity tests for criterion showed a specificity of 66%-100%, and showed high correlations with the reference scales when the questionnaire was assigning nursing diagnoses. Reliability tests showed agreement of 56%-91% (PQuestionnaire for Psychosocial Nursing Diagnosis was called CdePS, and included 61 items. The CdePS is a valid, reliable and easy-to-use tool in Primary Care centres to improve the assigning of a psychosocial nursing diagnosis. Copyright © 2011 Elsevier España, S.L. All rights reserved.

Centrifuge workers study. Phase II, completion report

International Nuclear Information System (INIS)

Wooten, H.D.

1994-09-01

Phase II of the Centrifuge Workers Study was a follow-up to the Phase I efforts. The Phase I results had indicated a higher risk than expected among centrifuge workers for developing bladder cancer when compared with the risk in the general population for developing this same type of cancer. However, no specific agent could be identified as the causative agent for these bladder cancers. As the Phase II Report states, Phase I had been limited to workers who had the greatest potential for exposure to substances used in the centrifuge process. Phase II was designed to expand the survey to evaluate the health of all employees who had ever worked in Centrifuge Program Departments 1330-1339 but who had not been interviewed in Phase I. Employees in analytical laboratories and maintenance departments who provided support services for the Centrifuge Program were also included in Phase II. In December 1989, the Oak Ridge Associated Universities (ORAU), now known as Oak Ridge Institute for Science and Education (ORISE), was contracted to conduct a follow-up study (Phase II). Phase H of the Centrifuge Workers Study expanded the survey to include all former centrifuge workers who were not included in Phase I. ORISE was chosen because they had performed the Phase I tasks and summarized the corresponding survey data therefrom

Centrifuge workers study. Phase II, completion report

Energy Technology Data Exchange (ETDEWEB)

Wooten, H.D.

1994-09-01

Phase II of the Centrifuge Workers Study was a follow-up to the Phase I efforts. The Phase I results had indicated a higher risk than expected among centrifuge workers for developing bladder cancer when compared with the risk in the general population for developing this same type of cancer. However, no specific agent could be identified as the causative agent for these bladder cancers. As the Phase II Report states, Phase I had been limited to workers who had the greatest potential for exposure to substances used in the centrifuge process. Phase II was designed to expand the survey to evaluate the health of all employees who had ever worked in Centrifuge Program Departments 1330-1339 but who had not been interviewed in Phase I. Employees in analytical laboratories and maintenance departments who provided support services for the Centrifuge Program were also included in Phase II. In December 1989, the Oak Ridge Associated Universities (ORAU), now known as Oak Ridge Institute for Science and Education (ORISE), was contracted to conduct a follow-up study (Phase II). Phase H of the Centrifuge Workers Study expanded the survey to include all former centrifuge workers who were not included in Phase I. ORISE was chosen because they had performed the Phase I tasks and summarized the corresponding survey data therefrom.

Development and validation of a notational system to study the offensive process in football.

Science.gov (United States)

Sarmento, Hugo; Anguera, Teresa; Campaniço, Jorge; Leitão, José

2010-01-01

The most striking change within football development is the application of science to its problems and in particular the use of increasingly sophisticated technology that, supported by scientific data, allows us to establish a "code of reading" the reality of the game. Therefore, this study describes the process of the development and validation of an ad hoc system of categorization, which allows the different methods of offensive game in football and the interaction to be analyzed. Therefore, through an exploratory phase of the study, we identified 10 vertebrate criteria and the respective behaviors observed for each of these criteria. We heard a panel of five experts with the purpose of a content validation. The resulting instrument is characterized by a combination of field formats and systems of categories. The reliability of the instrument was calculated by the intraobserver agreement, and values above 0.95 for all criteria were achieved. Two FC Barcelona games were coded and analyzed, which allowed the detection of various T-patterns. The results show that the instrument serves the purpose for which it was developed and can provide important information for the understanding of game interaction in football.

The accomplishments of lithium target and test facility validation activities in the IFMIF/EVEDA phase

Science.gov (United States)

Arbeiter, Frederik; Baluc, Nadine; Favuzza, Paolo; Gröschel, Friedrich; Heidinger, Roland; Ibarra, Angel; Knaster, Juan; Kanemura, Takuji; Kondo, Hiroo; Massaut, Vincent; Saverio Nitti, Francesco; Miccichè, Gioacchino; O'hira, Shigeru; Rapisarda, David; Sugimoto, Masayoshi; Wakai, Eiichi; Yokomine, Takehiko

2018-01-01

As part of the engineering validation and engineering design activities (EVEDA) phase for the international fusion materials irradiation facility IFMIF, major elements of a lithium target facility and the test facility were designed, prototyped and validated. For the lithium target facility, the EVEDA lithium test loop was built at JAEA and used to test the stability (waves and long term) of the lithium flow in the target, work out the startup procedures, and test lithium purification and analysis. It was confirmed by experiments in the Lifus 6 plant at ENEA that lithium corrosion on ferritic martensitic steels is acceptably low. Furthermore, complex remote handling procedures for the remote maintenance of the target in the test cell environment were successfully practiced. For the test facility, two variants of a high flux test module were prototyped and tested in helium loops, demonstrating their good capabilities of maintaining the material specimens at the desired temperature with a low temperature spread. Irradiation tests were performed for heated specimen capsules and irradiation instrumentation in the BR2 reactor at SCK-CEN. The small specimen test technique, essential for obtaining material test results with limited irradiation volume, was advanced by evaluating specimen shape and test technique influences.

Validity of two-phase polymer electrolyte membrane fuel cell models with respect to the gas diffusion layer

Science.gov (United States)

Ziegler, C.; Gerteisen, D.

A dynamic two-phase model of a proton exchange membrane fuel cell with respect to the gas diffusion layer (GDL) is presented and compared with chronoamperometric experiments. Very good agreement between experiment and simulation is achieved for potential step voltammetry (PSV) and sine wave testing (SWT). Homogenized two-phase models can be categorized in unsaturated flow theory (UFT) and multiphase mixture (M 2) models. Both model approaches use the continuum hypothesis as fundamental assumption. Cyclic voltammetry experiments show that there is a deterministic and a stochastic liquid transport mode depending on the fraction of hydrophilic pores of the GDL. ESEM imaging is used to investigate the morphology of the liquid water accumulation in the pores of two different media (unteflonated Toray-TGP-H-090 and hydrophobic Freudenberg H2315 I3). The morphology of the liquid water accumulation are related with the cell behavior. The results show that UFT and M 2 two-phase models are a valid approach for diffusion media with large fraction of hydrophilic pores such as unteflonated Toray-TGP-H paper. However, the use of the homgenized UFT and M 2 models appears to be invalid for GDLs with large fraction of hydrophobic pores that corresponds to a high average contact angle of the GDL.

Simulation Based Studies in Software Engineering: A Matter of Validity

Directory of Open Access Journals (Sweden)

Breno Bernard Nicolau de França

2015-04-01

Full Text Available Despite the possible lack of validity when compared with other science areas, Simulation-Based Studies (SBS in Software Engineering (SE have supported the achievement of some results in the field. However, as it happens with any other sort of experimental study, it is important to identify and deal with threats to validity aiming at increasing their strength and reinforcing results confidence. OBJECTIVE: To identify potential threats to SBS validity in SE and suggest ways to mitigate them. METHOD: To apply qualitative analysis in a dataset resulted from the aggregation of data from a quasi-systematic literature review combined with ad-hoc surveyed information regarding other science areas. RESULTS: The analysis of data extracted from 15 technical papers allowed the identification and classification of 28 different threats to validity concerned with SBS in SE according Cook and Campbell’s categories. Besides, 12 verification and validation procedures applicable to SBS were also analyzed and organized due to their ability to detect these threats to validity. These results were used to make available an improved set of guidelines regarding the planning and reporting of SBS in SE. CONCLUSIONS: Simulation based studies add different threats to validity when compared with traditional studies. They are not well observed and therefore, it is not easy to identify and mitigate all of them without explicit guidance, as the one depicted in this paper.

Pre-validation methods for developing a patient reported outcome instrument

Directory of Open Access Journals (Sweden)

Castillo Mayret M

2011-08-01

Full Text Available Abstract Background Measures that reflect patients' assessment of their health are of increasing importance as outcome measures in randomised controlled trials. The methodological approach used in the pre-validation development of new instruments (item generation, item reduction and question formatting should be robust and transparent. The totality of the content of existing PRO instruments for a specific condition provides a valuable resource (pool of items that can be utilised to develop new instruments. Such 'top down' approaches are common, but the explicit pre-validation methods are often poorly reported. This paper presents a systematic and generalisable 5-step pre-validation PRO instrument methodology. Methods The method is illustrated using the example of the Aberdeen Glaucoma Questionnaire (AGQ. The five steps are: 1 Generation of a pool of items; 2 Item de-duplication (three phases; 3 Item reduction (two phases; 4 Assessment of the remaining items' content coverage against a pre-existing theoretical framework appropriate to the objectives of the instrument and the target population (e.g. ICF; and 5 qualitative exploration of the target populations' views of the new instrument and the items it contains. Results The AGQ 'item pool' contained 725 items. Three de-duplication phases resulted in reduction of 91, 225 and 48 items respectively. The item reduction phases discarded 70 items and 208 items respectively. The draft AGQ contained 83 items with good content coverage. The qualitative exploration ('think aloud' study resulted in removal of a further 15 items and refinement to the wording of others. The resultant draft AGQ contained 68 items. Conclusions This study presents a novel methodology for developing a PRO instrument, based on three sources: literature reporting what is important to patient; theoretically coherent framework; and patients' experience of completing the instrument. By systematically accounting for all items dropped

Development and validation of a learning progression for change of seasons, solar and lunar eclipses, and moon phases

Science.gov (United States)

Testa, Italo; Galano, Silvia; Leccia, Silvio; Puddu, Emanuella

2015-12-01

In this paper, we report about the development and validation of a learning progression about the Celestial Motion big idea. Existing curricula, research studies on alternative conceptions about these phenomena, and students' answers to an open questionnaire were the starting point to develop initial learning progressions about change of seasons, solar and lunar eclipses, and Moon phases; then, a two-tier multiple choice questionnaire was designed to validate and improve them. The questionnaire was submitted to about 300 secondary students of different school levels (14 to 18 years old). Item response analysis and curve integral method were used to revise the hypothesized learning progressions. Findings support that spatial reasoning is a key cognitive factor for building an explanatory framework for the Celestial Motion big idea, but also suggest that causal reasoning based on physics mechanisms underlying the phenomena, as light flux laws or energy transfers, may significantly impact a students' understanding. As an implication of the study, we propose that the teaching of the three discussed astronomy phenomena should follow a single teaching-learning path along the following sequence: (i) emphasize from the beginning the geometrical aspects of the Sun-Moon-Earth system motion; (ii) clarify consequences of the motion of the Sun-Moon-Earth system, as the changing solar radiation flow on the surface of Earth during the revolution around the Sun; (iii) help students moving between different reference systems (Earth and space observer's perspective) to understand how Earth's rotation and revolution can change the appearance of the Sun and Moon. Instructional and methodological implications are also briefly discussed.

Dynamic modeling and experimental validation for direct contact membrane distillation (DCMD) process

KAUST Repository

Eleiwi, Fadi

2016-02-01

This work proposes a mathematical dynamic model for the direct contact membrane distillation (DCMD) process. The model is based on a 2D Advection–Diffusion Equation (ADE), which describes the heat and mass transfer mechanisms that take place inside the DCMD module. The model studies the behavior of the process in the time varying and the steady state phases, contributing to understanding the process performance, especially when it is driven by intermittent energy supply, such as the solar energy. The model is experimentally validated in the steady state phase, where the permeate flux is measured for different feed inlet temperatures and the maximum absolute error recorded is 2.78 °C. Moreover, experimental validation includes the time variation phase, where the feed inlet temperature ranges from 30 °C to 75 °C with 0.1 °C increment every 2min. The validation marks relative error to be less than 5%, which leads to a strong correlation between the model predictions and the experiments.

Dynamic modeling and experimental validation for direct contact membrane distillation (DCMD) process

KAUST Repository

Eleiwi, Fadi; Ghaffour, NorEddine; Alsaadi, Ahmad Salem; Francis, Lijo; Laleg-Kirati, Taous-Meriem

2016-01-01

This work proposes a mathematical dynamic model for the direct contact membrane distillation (DCMD) process. The model is based on a 2D Advection–Diffusion Equation (ADE), which describes the heat and mass transfer mechanisms that take place inside the DCMD module. The model studies the behavior of the process in the time varying and the steady state phases, contributing to understanding the process performance, especially when it is driven by intermittent energy supply, such as the solar energy. The model is experimentally validated in the steady state phase, where the permeate flux is measured for different feed inlet temperatures and the maximum absolute error recorded is 2.78 °C. Moreover, experimental validation includes the time variation phase, where the feed inlet temperature ranges from 30 °C to 75 °C with 0.1 °C increment every 2min. The validation marks relative error to be less than 5%, which leads to a strong correlation between the model predictions and the experiments.

Investigating Phase Transform Behavior in Indium Selenide Based RAM and Its Validation as a Memory Element

Directory of Open Access Journals (Sweden)

Swapnil Sourav

2016-01-01

Full Text Available Phase transform properties of Indium Selenide (In2Se3 based Random Access Memory (RAM have been explored in this paper. Phase change random access memory (PCRAM is an attractive solid-state nonvolatile memory that possesses potential to meet various current technology demands of memory design. Already reported PCRAM models are mainly based upon Germanium-Antimony-Tellurium (Ge2Sb2Te5 or GST materials as their prime constituents. However, PCRAM using GST material lacks some important memory attributes required for memory elements such as larger resistance margin between the highly resistive amorphous and highly conductive crystalline states in phase change materials. This paper investigates various electrical and compositional properties of the Indium Selenide (In2Se3 material and also draws comparison with its counterpart mainly focusing on phase transform properties. To achieve this goal, a SPICE model of In2Se3 based PCRAM model has been reported in this work. The reported model has been also validated to act as a memory cell by associating it with a read/write circuit proposed in this work. Simulation results demonstrate impressive retentivity and low power consumption by requiring a set pulse of 208 μA for a duration of 100 μs to set the PCRAM in crystalline state. Similarly, a reset pulse of 11.7 μA for a duration of 20 ns can set the PCRAM in amorphous state. Modeling of In2Se3 based PCRAM has been done in Verilog-A and simulation results have been extensively verified using SPICE simulator.

Development and Validation of Chemistry Self-Efficacy Scale for College Students

Science.gov (United States)

Uzuntiryaki, Esen; Çapa Aydın, Yeşim

2009-08-01

This study described the process of developing and validating the College Chemistry Self-Efficacy Scale (CCSS) that can be used to assess college students’ beliefs in their ability to perform essential tasks in chemistry. In the first phase, data collected from 363 college students provided evidence for the validity and reliability of the new scale. Three dimensions emerged: self-efficacy for cognitive skills, self-efficacy for psychomotor skills, and self-efficacy for everyday applications. In the second phase, data collected from an independent sample of 353 college students confirmed the factorial structure of the 21-item CCSS. The Cronbach alpha coefficients ranged from 0.82 to 0.92. In addition, each dimension of the CCSS had moderate and significant correlations with student chemistry achievement and differentiated between major and non-major students. Followed by the additional validation studies, the CCSS will serve as a valuable tool for both instructors and researchers in science education to assess college students’ chemistry self-efficacy beliefs.

Study and modeling of the dispersed phase behavior in a pulsed column: application to an oxalic precipitation process

International Nuclear Information System (INIS)

Amokrane, Abdenour

2014-01-01

The thesis focuses on the study and modeling of a pulsed column used in liquid-liquid extraction operations in the nuclear industry and which is otherwise considered for continuous precipitation operations in emulsion. Modeling the behavior of the dispersed phase in the column is undertaken in this manuscript. First, we began by modeling the continuous phase mean velocity and turbulence fields, which are responsible for transport, breakage and coalescence of the drops. The model developed, validated by PIV measurements, predicts turbulence in a satisfying way. Modeling the residence time distribution (RTD) of the drops by a Lagrangian approach is then achieved. This model is validated on measurements taken by a shadow-graph technique. The simulation results are in good agreement with the experimental ones. To model the droplet size distributions (DSD) in the column, we used the population balance equations (PBE) that we have coupled with the computational fluid dynamics equations (CFD). A continuously stirred tank reactor (CSTR) with an optical sensor is used, at first, to acquire the DSD representative of our liquid-liquid system. Through a 0D modeling of the flow in the CSTR, and solving the inverse problem, we have determined the breakage and coalescence kernels relevant for our system, to be used in the PBE. These kernels were then used to predict the DSD in the pulsed column by a coupled CFD-PBE model based on the QMOM method. Finally, a validation of the coupled CFD-PBE model is made from DSD in good agreement with the experimental data both qualitatively and quantitatively. The validated model is then used to study the emulsion sensitivity to the column operating conditions. (author) [fr

Valid Competency Assessment in Higher Education

Directory of Open Access Journals (Sweden)

Olga Zlatkin-Troitschanskaia

2017-01-01

Full Text Available The aim of the 15 collaborative projects conducted during the new funding phase of the German research program Modeling and Measuring Competencies in Higher Education—Validation and Methodological Innovations (KoKoHs is to make a significant contribution to advancing the field of modeling and valid measurement of competencies acquired in higher education. The KoKoHs research teams assess generic competencies and domain-specific competencies in teacher education, social and economic sciences, and medicine based on findings from and using competency models and assessment instruments developed during the first KoKoHs funding phase. Further, they enhance, validate, and test measurement approaches for use in higher education in Germany. Results and findings are transferred at various levels to national and international research, higher education practice, and education policy.

Numerical Study of Particle Interaction in Gas-Particle and Liquid-Particle Flows: Part I Analysis and Validation

Directory of Open Access Journals (Sweden)

K. Mohanarangam

2009-09-01

Full Text Available A detailed study into the turbulent behaviour of dilute particulate flow under the influence of two carrier phases namely gas and liquid has been carried out behind a sudden expansion geometry. The major endeavour of the study is to ascertain the response of the particles within the carrier (gas or liquid phase. The main aim prompting the current study is the density difference between the carrier and the dispersed phases. While the ratio is quite high in terms of the dispersed phase for the gas-particle flows, the ratio is far more less in terms of the liquid-particle flows. Numerical simulations were carried out for both these classes of flows using an Eulerian two-fluid model with RNG based k-emodel as the turbulent closure. An additional kinetic energy equation to better represent the combined fluid-particle behaviour is also employed in the current set of simulations. In the first part of this two part series, experimental results of Fessler and Eaton (1995 for Gas-Particle (GP flow and that of Founti and Klipfel (1998 for Liquid-Particle (LP flow have been compared and analysed. This forms the basis of the current study which aims to look at the particulate behaviour under the influence of two carrier phases. Further numerical simulations were carried out to test whether the current numerical formulation can used to simulate these varied type of flows and the same were validated against the experimental data of both GP as well LP flow. Qualitative results have been obtained for both these classes of flows with their respective experimental data both at the mean as well as at the turbulence level for carrier as well as the dispersed phases.

Validation of energy intake estimated from a food frequency questionnaire: a doubly labelled water study.

Science.gov (United States)

Andersen, L Frost; Tomten, H; Haggarty, P; Løvø, A; Hustvedt, B-E

2003-02-01

The validation of dietary assessment methods is critical in the evaluation of the relation between dietary intake and health. The aim of this study was to assess the validity of a food frequency questionnaire by comparing energy intake with energy expenditure measured with the doubly labelled water method. Total energy expenditure was measured with the doubly labelled water (DLW) method during a 10 day period. Furthermore, the subjects filled in the food frequency questionnaire about 18-35 days after the DLW phase of the study was completed. Twenty-one healthy, non-pregnant females volunteered to participate in the study; only 17 subjects completed the study. The group energy intake was on average 10% lower than the energy expenditure, but the difference was not statistically significant. However, there was a wide range in reporting accuracy: seven subjects were identified as acceptable reporters, eight as under-reporters and two were identified as over-reporters. The width of the 95% confidence limits of agreement in a Bland and Altman plot for energy intake and energy expenditure varied from -5 to 3 MJ. The data showed that there was substantial variability in the accuracy of the food frequency questionnaire at the individual level. Furthermore, the results showed that the questionnaire was more accurate for groups than individuals.

California Diploma Project Technical Report III: Validity Study--Validity Study of the Health Sciences and Medical Technology Standards

Science.gov (United States)

McGaughy, Charis; Bryck, Rick; de Gonzalez, Alicia

2012-01-01

This study is a validity study of the recently revised version of the Health Science Standards. The purpose of this study is to understand how the Health Science Standards relate to college and career readiness, as represented by survey ratings submitted by entry-level college instructors of health science courses and industry representatives. For…

Dysphagia in Multiple Sclerosis: Evaluation and Validation of the DYMUS Questionnaire.

Science.gov (United States)

Alali, Dalal; Ballard, Kirrie; Vucic, Steve; Bogaardt, Hans

2018-06-01

The 10-item Dysphagia in Multiple Sclerosis (DYMUS) questionnaire is a self-administered tool used to identify swallowing problems in adults with MS. The questionnaire was not validated against other existing questionnaires to assess its convergent validity. Moreover, its test-retest reliability was not measured previously. Therefore, the purpose of this study was to assess the factor analysis, internal consistency and test-retest reliability of the DYMUS, as well as its convergent validity against an established and validated questionnaire, the EAT-10. English-speaking adults with MS in New South Wales, Australia who were seen for routine medical check-ups were invited to complete two questionnaires across two phases. One hundred participants completed phase 1, while 55 completed phase 2. Statistical analyses were performed to investigate the psychometric properties of the DYMUS questionnaire. Internal consistency (Cronbach's Alpha) reduced the DYMUS questionnaire from ten to five items. The shortened version of the DYMUS showed high internal consistency (alpha = 0.904). It also showed satisfactory reproducibility, and adequate correlation with the 10-item Eating Assessment Tool (EAT-10). Evaluation of the DYMUS resulted in a shortened version of the questionnaire with five questions related to dysphagia. This shortened version is considered an easy and useful tool in identifying patients with MS-related dysphagia.

Validity and Reliability of Knowledge, Attitude and Behavior Assessment Tool Among Vulnerable Women Concerning Sexually Transmitted Diseases

Directory of Open Access Journals (Sweden)

Zahra Boroumandfar

2016-05-01

Full Text Available Objective: The study aimed to design and evaluate the content and face validity, and reliability of knowledge, attitude, and behavior questionnaire on preventive behaviors among vulnerable women concerning sexually transmitted diseases (STDs.Materials and methods: This cross-sectional study was carried out in two phases of an action research. In the first phase, to explain STDs preventive domains, 20 semi- structured interviews were conducted with the vulnerable women, residing at women prison and women referred to counseling centers. After analyzing content of interviews, three domains were identified: improve their knowledge, modify their attitude and change their behaviors. In the second phase, the questionnaire was designed and tested in a pilot study. Then, its content validity was evaluated. Face validity and reliability of the questionnaire were assessed by test re- test method and Cronbach alpha respectively.Results: Index of content validity in each three domain of the questionnaire (knowledge, attitude and behavior concerning STDs was obtained over 0.6. Overall content validity index was 0.86 in all three domains of the questionnaire. The Cronbach’s alpha as reliability of questionnaire was 0.80 for knowledge, 0.79 for attitude and 0.85 for behavior.Conclusion: The results showed that the designed questionnaire was a valid and reliable tool to measure knowledge, attitude and behavior of vulnerable women, predisposed to risk of STDs.

Validation of the generalized model of two-phase thermosyphon loop based on experimental measurements of volumetric flow rate

Science.gov (United States)

Bieliński, Henryk

2016-09-01

The current paper presents the experimental validation of the generalized model of the two-phase thermosyphon loop. The generalized model is based on mass, momentum, and energy balances in the evaporators, rising tube, condensers and the falling tube. The theoretical analysis and the experimental data have been obtained for a new designed variant. The variant refers to a thermosyphon loop with both minichannels and conventional tubes. The thermosyphon loop consists of an evaporator on the lower vertical section and a condenser on the upper vertical section. The one-dimensional homogeneous and separated two-phase flow models were used in calculations. The latest minichannel heat transfer correlations available in literature were applied. A numerical analysis of the volumetric flow rate in the steady-state has been done. The experiment was conducted on a specially designed test apparatus. Ultrapure water was used as a working fluid. The results show that the theoretical predictions are in good agreement with the measured volumetric flow rate at steady-state.

A Novel Three Phase to Seven Phase Conversion Technique Using Transformer Winding Connections

Directory of Open Access Journals (Sweden)

M. Tabrez

2017-10-01

Full Text Available This paper proposes a novel multiphase transformer connection scheme which converts three phase balanced AC input to seven phase balanced AC output. Generalized theory to convert a three phase utility supply into any number of phases is presented. Based on the proposed generalized principle, a three phase to seven phase power converting transformer design is presented with connection scheme, analysis and simulation and experimental results of the proposed three phase to seven phase conversion transformer. The proposed transformer in this paper is analyzed and compared with the connection scheme for seven phase available in the literature. The connection scheme is found to have higher power density, lower core area and lower core requirement as compared to the available connection scheme of the same rating. Impedance mismatching between different phases of the transformer is observed in the three phase to seven phase transformer available in the literature. As this mismatching introduces error in study of per phase equivalent circuit diagrams as well as imbalance in voltage and currents. The present design also addresses the impedance mismatching issue and reduces mismatching in the proposed transformer design. A prototype of the proposed system is developed and waveforms are presented. The proposed design is verified using simulation and validated using experimental approach.

Validity of computational hemodynamics in human arteries based on 3D time-of-flight MR angiography and 2D electrocardiogram gated phase contrast images

Science.gov (United States)

Yu, Huidan (Whitney); Chen, Xi; Chen, Rou; Wang, Zhiqiang; Lin, Chen; Kralik, Stephen; Zhao, Ye

2015-11-01

In this work, we demonstrate the validity of 4-D patient-specific computational hemodynamics (PSCH) based on 3-D time-of-flight (TOF) MR angiography (MRA) and 2-D electrocardiogram (ECG) gated phase contrast (PC) images. The mesoscale lattice Boltzmann method (LBM) is employed to segment morphological arterial geometry from TOF MRA, to extract velocity profiles from ECG PC images, and to simulate fluid dynamics on a unified GPU accelerated computational platform. Two healthy volunteers are recruited to participate in the study. For each volunteer, a 3-D high resolution TOF MRA image and 10 2-D ECG gated PC images are acquired to provide the morphological geometry and the time-varying flow velocity profiles for necessary inputs of the PSCH. Validation results will be presented through comparisons of LBM vs. 4D Flow Software for flow rates and LBM simulation vs. MRA measurement for blood flow velocity maps. Indiana University Health (IUH) Values Fund.

Validation of a new assessment tool for qualitative research articles

DEFF Research Database (Denmark)

Schou, Lone; Høstrup, Helle; Lyngsø, Elin

2012-01-01

schou l., høstrup h., lyngsø e.e., larsen s. & poulsen i. (2011) Validation of a new assessment tool for qualitative research articles. Journal of Advanced Nursing00(0), 000-000. doi: 10.1111/j.1365-2648.2011.05898.x ABSTRACT: Aim.  This paper presents the development and validation of a new...... assessment tool for qualitative research articles, which could assess trustworthiness of qualitative research articles as defined by Guba and at the same time aid clinicians in their assessment. Background.  There are more than 100 sets of proposals for quality criteria for qualitative research. However, we...... is the Danish acronym for Appraisal of Qualitative Studies. Phase 1 was to develop the tool based on a literature review and on consultation with qualitative researchers. Phase 2 was an inter-rater reliability test in which 40 health professionals participated. Phase 3 was an inter-rater reliability test among...

Study of Pu consumption in light water reactors: Evaluation of GE advanced boiling water reactor plants, compilation of Phase 1C task reports

Energy Technology Data Exchange (ETDEWEB)

1994-01-15

This report summarizes the evaluations conducted during Phase 1C of the Pu Disposition Study have provided further results which reinforce the conclusions reached during Phase 1A & 1B: These conclusions clearly establish the benefits of the fission option and the use of the ABWR as a reliable, proven, well-defined and cost-effective means available to disposition the weapons Pu. This project could be implemented in the near-term at a cost and on a schedule being validated by reactor plants currently under construction in Japan and by cost and schedule history and validated plans for MOX plants in Europe. Evaluations conducted during this phase have established that (1) the MOX fuel is licensable based on existing criteria for new fuel with limited lead fuel rod testing, (2) that the applicable requirements for transport, handling and repository storage can be met, and (3) that all the applicable safeguards criteria can be met.

Study of Pu consumption in light water reactors: Evaluation of GE advanced boiling water reactor plants, compilation of Phase 1C task reports

International Nuclear Information System (INIS)

1994-01-01

This report summarizes the evaluations conducted during Phase 1C of the Pu Disposition Study have provided further results which reinforce the conclusions reached during Phase 1A ampersand 1B: These conclusions clearly establish the benefits of the fission option and the use of the ABWR as a reliable, proven, well-defined and cost-effective means available to disposition the weapons Pu. This project could be implemented in the near-term at a cost and on a schedule being validated by reactor plants currently under construction in Japan and by cost and schedule history and validated plans for MOX plants in Europe. Evaluations conducted during this phase have established that (1) the MOX fuel is licensable based on existing criteria for new fuel with limited lead fuel rod testing, (2) that the applicable requirements for transport, handling and repository storage can be met, and (3) that all the applicable safeguards criteria can be met

Diagnosing paratonia in the demented elderly: reliability and validity of the Paratonia Assessment Instrument (PAI).

Science.gov (United States)

Hobbelen, Johannes S M; Koopmans, Raymond T C M; Verhey, Frans R J; Habraken, Kitty M; de Bie, Rob A

2008-08-01

Paratonia is one of the associated movement disorders characteristic of dementia. The aim of this study was to develop an assessment tool (the Paratonia Assessment Instrument, PAI), based on the new consensus definition of paratonia. An additional aim was to investigate the reliability and validity of the PAI. A three-phase cross-sectional survey was conducted. In the first two phases, the PAI was developed and validated. In the third phase, the inter-observer reliability and feasibility of the instrument was tested. The original PAI consisted of five criteria that all needed to be met in order to make the diagnosis. On the basis of a qualitative analysis, one criterion was reformulated and another was removed. Following this, inter-observer reliability between the two assessors resulted in an improvement of Cohen's kappa from 0.532 in the initial phase to 0.677 in the second phase. This improvement was substantiated in the third phase by two independent assessors with Cohen's kappa ranging from 0.625 to 1. The PAI is a reliable and valid assessment tool for diagnosing paratonia in elderly people with dementia that can be applied easily in daily practice.

Development and Validation of a Reversed-Phase Liquid Chromatography Method for the Simultaneous Determination of Indole-3-Acetic Acid, Indole-3-Pyruvic Acid, and Abscisic Acid in Barley (Hordeum vulgare L.).

Science.gov (United States)

Nakurte, Ilva; Keisa, Anete; Rostoks, Nils

2012-01-01

A simple, sensitive, precise, and specific reverse HPLC method was developed and validated for the determination of plant hormones in barley (Hordeum vulgare L.). The method includes extraction in aqueous organic solvent followed by solid-phase extraction, sample evaporation, and reversed-phase HPLC analysis in a general purpose UV-visible (abscisic acid (ABA)) and fluorescence detection (indole-3-acetic acid (IAA) and indole-3-pyruvic acid (IPA)), high-performance liquid chromatography system. The separation was carried out on Zorbax Eclipse XDB C8 column (150  ×  4.6  mm I.D) with a mobile phase composed of methanol and 1% acetic acid (60 : 40 v/v) in isocratic mode at a flow rate of 1 ml min(-1). The detection was monitored at 270 nm (ABA) and at 282 nm (Ex) and 360 nm (Em) (IAA, IPA). The developed method was validated in terms of accuracy, precision, linearity, limit of detection, limit of quantification, and robustness. The determined validation parameters are in the commonly acceptable ranges for that kind of analysis.

Seabrook simulator model upgrade: Implementation and validation of two-phase, nonequilibrium RCS and steam generator models

International Nuclear Information System (INIS)

Kao, S.

1990-01-01

A number of deficiencies in the original RCS and steam generator models on the Seabrook simulator were found to give unrealistic results under some off-normal and accident conditions. These deficiencies are attributed to the simplistic assumptions used in the original models, such as the homogeneous, equilibrium equations used in the pressurizer and steam generator models, and the single-phase flow model used in the RCS thermal-hydraulic model. To improve the fidelity of the simulator, efforts have been made to upgrade the RCS and steam generator models to include two-phase, nonequilibrium features. In the new RCS model, the following major assumptions are used to derive the finite difference form of the conservation equations: a donor-cell differencing scheme is adopted to allow flow reversal; a single pressure is used to evaluate properties; a single mass flow rate is assumed in each loop; enthalpy is assumed to vary linearly within each control volume; a homogeneous flow is assumed under two-phase conditions. The pressurizer is divided into a vapor region and a liquid region, each of which is represented by a set of mass and energy conservation equations. Interfacial mass and energy exchange mechanisms (condensation and flashing), thermal interactions between the vessel and fluids, and thermal nonequilibrium between the phases are included in the pressurizer model. The steam generator is divided into the vapor dome, riser, and downcomer regions. The assumptions applied are similar to those of the RCS and pressurizer models. A momentum model is incorporated to calculate the recirculation flow and simulate the downcomer level shrink/swell phenomenon. The new RCS and steam generator models are validated by comparing the simulator calculations against sister plant data and FSAR vendor analysis. The results show the new models give realistic and reliable calculations under off-normal and accident conditions

A validated RP-HPLC method for the determination of Irinotecan hydrochloride residues for cleaning validation in production area

Directory of Open Access Journals (Sweden)

Sunil Reddy

2013-03-01

Full Text Available Introduction: cleaning validation is an integral part of current good manufacturing practices in pharmaceutical industry. The main purpose of cleaning validation is to prove the effectiveness and consistency of cleaning in a given pharmaceutical production equipment to prevent cross contamination and adulteration of drug product with other active ingredient. Objective: a rapid, sensitive and specific reverse phase HPLC method was developed and validated for the quantitative determination of irinotecan hydrochloride in cleaning validation swab samples. Method: the method was validated using waters symmetry shield RP-18 (250mm x 4.6mm 5 µm column with isocratic mobile phase containing a mixture of 0.02 M potassium di-hydrogen ortho-phosphate, pH adjusted to 3.5 with ortho-phosphoric acid, methanol and acetonitrile (60:20:20 v/v/v. The flow rate of mobile phase was 1.0 mL/min with column temperature of 25°C and detection wavelength at 220nm. The sample injection volume was 100 µl. Results: the calibration curve was linear over a concentration range from 0.024 to 0.143 µg/mL with a correlation coefficient of 0.997. The intra-day and inter-day precision expressed as relative standard deviation were below 3.2%. The recoveries obtained from stainless steel, PCGI, epoxy, glass and decron cloth surfaces were more than 85% and there was no interference from the cotton swab. The detection limit (DL and quantitation limit (QL were 0.008 and 0.023 µg ml-1, respectively. Conclusion: the developed method was validated with respect to specificity, linearity, limit of detection and quantification, accuracy, precision and solution stability. The overall procedure can be used as part of a cleaning validation program in pharmaceutical manufacture of irinotecan hydrochloride.

Cyber Victim and Bullying Scale: A Study of Validity and Reliability

Science.gov (United States)

Cetin, Bayram; Yaman, Erkan; Peker, Adem

2011-01-01

The purpose of this study is to develop a reliable and valid scale, which determines cyber victimization and bullying behaviors of high school students. Research group consisted of 404 students (250 male, 154 male) in Sakarya, in 2009-2010 academic years. In the study sample, mean age is 16.68. Content validity and face validity of the scale was…

Dosimetric studies for gamma radiation validation of medical devices

International Nuclear Information System (INIS)

Soliman, Y.S.; Beshir, W.B.; Abdel-Fattah, A.A.; Abdel-Rehim, F.

2013-01-01

The delivery and validation of a specified dose to medical devices are key concerns to operators of gamma radiation facilities. The objective of the present study was to characterize the industrial gamma radiation facility and map the dose distribution inside the product-loading pattern during the validation and routine control of the sterilization process using radiochromic films. Cardboard phantoms were designed to achieve the homogeneity of absorbed doses. The uncertainty of the dose delivered during validation of the sterilization process was assessed. - Highlights: ► Using γ-rays for sterilization of hollow fiber dialyzers and blood tubing sets according to ISO 11137, 2006. ► Dosimetry studies of validations of γ-irradiation facility and sterilized medical devices. ► Places of D min and D max have been determined using FWT-60 films. ► Determining the target minimum doses required to meet the desired SAL of 10 −6 for the two products.

Elaboration of a nomogram to predict nonsentinel node status in breast cancer patients with positive sentinel node, intraoperatively assessed with one step nucleic amplification: Retrospective and validation phase.

Science.gov (United States)

Di Filippo, Franco; Di Filippo, Simona; Ferrari, Anna Maria; Antonetti, Raffaele; Battaglia, Alessandro; Becherini, Francesca; Bernet, Laia; Boldorini, Renzo; Bouteille, Catherine; Buglioni, Simonetta; Burelli, Paolo; Cano, Rafael; Canzonieri, Vincenzo; Chiodera, Pierluigi; Cirilli, Alfredo; Coppola, Luigi; Drago, Stefano; Di Tommaso, Luca; Fenaroli, Privato; Franchini, Roberto; Gianatti, Andrea; Giannarelli, Diana; Giardina, Carmela; Godey, Florence; Grassi, Massimo M; Grassi, Giuseppe B; Laws, Siobhan; Massarut, Samuele; Naccarato, Giuseppe; Natalicchio, Maria Iole; Orefice, Sergio; Palmieri, Fabrizio; Perin, Tiziana; Roncella, Manuela; Roncalli, Massimo G; Rulli, Antonio; Sidoni, Angelo; Tinterri, Corrado; Truglia, Maria C; Sperduti, Isabella

2016-12-08

Tumor-positive sentinel lymph node (SLN) biopsy results in a risk of non sentinel node metastases in micro- and macro-metastases ranging from 20 to 50%, respectively. Therefore, most patients underwent unnecessary axillary lymph node dissections. We have previously developed a mathematical model for predicting patient-specific risk of non sentinel node (NSN) metastases based on 2460 patients. The study reports the results of the validation phase where a total of 1945 patients were enrolled, aimed at identifying a tool that gives the possibility to the surgeon to choose intraoperatively whether to perform or not axillary lymph node dissection (ALND). The following parameters were recorded: Clinical: hospital, age, medical record number; Bio pathological: Tumor (T) size stratified in quartiles, grading (G), histologic type, lymphatic/vascular invasion (LVI), ER-PR status, Ki 67, molecular classification (Luminal A, Luminal B, HER-2 Like, Triple negative); Sentinel and non-sentinel node related: Number of NSNs removed, number of positive NSNs, cytokeratin 19 (CK19) mRNA copy number of positive sentinel nodes stratified in quartiles. A total of 1945 patients were included in the database. All patient data were provided by the authors of this paper. The discrimination of the model quantified with the area under the receiver operating characteristics (ROC) curve (AUC), was 0.65 and 0.71 in the validation and retrospective phase, respectively. The calibration determines the distance between predicted outcome and actual outcome. The mean difference between predicted/observed was 2.3 and 6.3% in the retrospective and in the validation phase, respectively. The two values are quite similar and as a result we can conclude that the nomogram effectiveness was validated. Moreover, the ROC curve identified in the risk category of 31% of positive NSNs, the best compromise between false negative and positive rates i.e. when ALND is unnecessary (31%). The results of the study confirm

SAMICS validation. SAMICS support study: Phase III. Final report, Jet Propulsion Laboratory

Energy Technology Data Exchange (ETDEWEB)

1979-03-01

The purpose of SAMICS is to provide a consistent basis for estimating solar cell array costs and comparing production technology costs. The user of SAMICS provides detailed process information for calculating direct costs. To these are added indirect and overhead expenses. Although thorough documentation of direct processes requires a significant initial effort, the process gives SAMICS its primary strength. A complete accounting of direct process resource requirements establishes an audit trail that will help to monitor the realism of assumptions before production and to later identify variations from forecasted operating parameters after production begins. The purpose for this review were the following: (a) to test the computational validity of the computer model by comparison with preliminary hand calculations based on conventional cost estimating techniques; (b) to review and improve the accuracy of the cost relationships being used by the model; and (c) to provide an independent verification to users of the model's value in decision making for allocation of research and development funds and for investment in manufacturing capacity. The conclusion is that the SAMICS model is a flexible, accurate, and useful tool for managerial decision making. The comparison of model results with calculations shows close correlation. This report provides the basis for conclusions. It also contains recommendations for increasing the usefulness of SAMICS. (WHK)

Replication of LDL GWAs hits in PROSPER/PHASE as validation for future (pharmacogenetic analyses

Directory of Open Access Journals (Sweden)

Stott David J

2011-10-01

Full Text Available Abstract Background The PHArmacogenetic study of Statins in the Elderly at risk (PHASE is a genome wide association study in the PROspective Study of Pravastatin in the Elderly at risk for vascular disease (PROSPER that investigates the genetic variation responsible for the individual variation in drug response to pravastatin. Statins lower LDL-cholesterol in general by 30%, however not in all subjects. Moreover, clinical response is highly variable and adverse effects occur in a minority of patients. In this report we first describe the rationale of the PROSPER/PHASE project and second show that the PROSPER/PHASE study can be used to study pharmacogenetics in the elderly. Methods The genome wide association study (GWAS was conducted using the Illumina 660K-Quad beadchips following manufacturer's instructions. After a stringent quality control 557,192 SNPs in 5,244 subjects were available for analysis. To maximize the availability of genetic data and coverage of the genome, imputation up to 2.5 million autosomal CEPH HapMap SNPs was performed with MACH imputation software. The GWAS for LDL-cholesterol is assessed with an additive linear regression model in PROBABEL software, adjusted for age, sex, and country of origin to account for population stratification. Results Forty-two SNPs reached the GWAS significant threshold of p = 5.0e-08 in 5 genomic loci (APOE/APOC1; LDLR; FADS2/FEN1; HMGCR; PSRC1/CELSR5. The top SNP (rs445925, chromosome 19 with a p-value of p = 2.8e-30 is located within the APOC1 gene and near the APOE gene. The second top SNP (rs6511720, chromosome 19 with a p-value of p = 5.22e-15 is located within the LDLR gene. All 5 genomic loci were previously associated with LDL-cholesterol levels, no novel loci were identified. Replication in WOSCOPS and CARE confirmed our results. Conclusion With the GWAS in the PROSPER/PHASE study we confirm the previously found genetic associations with LDL-cholesterol levels. With this proof

Overview of the Exploration Exercise Device Validation Study Plans

Science.gov (United States)

DeWitt, J. K.; Swan, B. G.

2018-01-01

during design iterations. Assuming successful ground tests, the device will be installed on the ISS for testing during space flight. Spaceflight testing is envisioned to include an activation and checkout (ACO) phase and a V&V phase. During the ACO phase, 1-2 crewmembers will exercise with the device to ensure proper function. ACO is expected to last multiple months because of the many modes and methods of exercise that need to be assessed. However, the goal is to complete the ACO as quickly as possible. Once successful ACO occurs, the crew will be free to use the device for normal exercise pending concurrence from stakeholders. V&V tests on the ISS will ideally consist of crew using the device for all of their exercise for an entire mission. Exercise prescriptions will be supplied that replicate expected prescriptions during exploration missions. Crew that are not enrolled in the V&V studies would be also free to use the device as their schedule permits. As experience is gained by users, exercise protocols could change. The intent of all V&V testing is to ensure that all have thorough understanding of experience at optimizing device capability

Validation of Inter-Subject Training for Hidden Markov Models Applied to Gait Phase Detection in Children with Cerebral Palsy

Directory of Open Access Journals (Sweden)

Juri Taborri

2015-09-01

Full Text Available Gait-phase recognition is a necessary functionality to drive robotic rehabilitation devices for lower limbs. Hidden Markov Models (HMMs represent a viable solution, but they need subject-specific training, making data processing very time-consuming. Here, we validated an inter-subject procedure to avoid the intra-subject one in two, four and six gait-phase models in pediatric subjects. The inter-subject procedure consists in the identification of a standardized parameter set to adapt the model to measurements. We tested the inter-subject procedure both on scalar and distributed classifiers. Ten healthy children and ten hemiplegic children, each equipped with two Inertial Measurement Units placed on shank and foot, were recruited. The sagittal component of angular velocity was recorded by gyroscopes while subjects performed four walking trials on a treadmill. The goodness of classifiers was evaluated with the Receiver Operating Characteristic. The results provided a goodness from good to optimum for all examined classifiers (0 < G < 0.6, with the best performance for the distributed classifier in two-phase recognition (G = 0.02. Differences were found among gait partitioning models, while no differences were found between training procedures with the exception of the shank classifier. Our results raise the possibility of avoiding subject-specific training in HMM for gait-phase recognition and its implementation to control exoskeletons for the pediatric population.

Cooperative learning benefits scale: construction and validation studies

Directory of Open Access Journals (Sweden)

José Lopes

2014-07-01

Full Text Available The aim of this study was to develop and validate a scale of benefits of the Cooperative Learning (SBCL given the exiguity of instruments that evaluate these outputs of the method. The study resorted to a convenience sample comprised of 162 students, males and females, aged between 11 and 18 years. The final instrument has 23 items in a two-dimensional factor structure: psychological and academic benefits and social benefits. The results indicate that the SBCL present good psychometric properties (construct and discriminant validity and reliability. The results are discussed in light of the model of cooperative learning.

Advanced Concept Studies for Supersonic Commercial Transports Entering Service in the 2018-2020 Period Phase 2

Science.gov (United States)

Morgenstern, John; Buonanno, Michael; Yao, Jixian; Murugappan, Mugam; Paliath, Umesh; Cheung, Lawrence; Malcevic, Ivan; Ramakrishnan, Kishore; Pastouchenko, Nikolai; Wood, Trevor;

Validation of a two-fluid model used for the simulation of dense fluidized beds; Validation d`un modele a deux fluides applique a la simulation des lits fluidises denses

Energy Technology Data Exchange (ETDEWEB)

Boelle, A.

1997-02-17

A two-fluid model applied to the simulation of gas-solid dense fluidized beds is validated on micro scale and on macro scale. Phase coupling is carried out in the momentum and energy transport equation of both phases. The modeling is built on the kinetic theory of granular media in which the gas action has been taken into account in order to get correct expressions of transport coefficients. A description of hydrodynamic interactions between particles in high Stokes number flow is also incorporated in the model. The micro scale validation uses Lagrangian numerical simulations viewed as numerical experiments. The first validation case refers to a gas particle simple shear flow. It allows to validate the competition between two dissipation mechanisms: drag and particle collisions. The second validation case is concerted with sedimenting particles in high Stokes number flow. It allows to validate our approach of hydrodynamic interactions. This last case had led us to develop an original Lagrangian simulation with a two-way coupling between the fluid and the particles. The macro scale validation uses the results of Eulerian simulations of dense fluidized bed. Bed height, particles circulation and spontaneous created bubbles characteristics are studied and compared to experimental measurement, both looking at physical and numerical parameters. (author) 159 refs.

Validation of a raw data-based synchronization signal (kymogram) for phase-correlated cardiac image reconstruction

International Nuclear Information System (INIS)

Ertel, Dirk; Kachelriess, Marc; Kalender, Willi A.; Pflederer, Tobias; Achenbach, Stephan; Steffen, Peter

2008-01-01

Phase-correlated reconstruction is commonly used in computed tomography (CT)-based cardiac imaging. Alternatively to the commonly used ECG, the raw data-based kymogram function can be used as a synchronization signal. We used raw data of 100 consecutive patient exams to compare the performance of kymogram function to the ECG signal. For objective validation the correlation of the ECG and the kymogram was assessed. Additionally, we performed a double-blinded comparison of ECG-based and kymogram-based phase-correlated images. The two synchronization signals showed good correlation indicated by a mean difference in the detected heart rate of negligible 0.2 bpm. The mean image quality score was 2.0 points for kymogram-correlated images and 2.3 points for ECG-correlated images, respectively (3: best; 0: worst). The kymogram and the ECG provided images adequate for diagnosis for 93 and 97 patients, respectively. For 50% of the datasets the kymogram provided an equivalent or even higher image quality compared with the ECG signal. We conclude that an acceptable image quality can be assured in most cases by the kymogram. Improvements of image quality by the kymogram function were observed in a noticeable number of cases. The kymogram can serve as a backup solution when an ECG is not available or lacking in quality. (orig.)

BIOMOVS: an international model validation study

International Nuclear Information System (INIS)

Haegg, C.; Johansson, G.

1988-01-01

BIOMOVS (BIOspheric MOdel Validation Study) is an international study where models used for describing the distribution of radioactive and nonradioactive trace substances in terrestrial and aquatic environments are compared and tested. The main objectives of the study are to compare and test the accuracy of predictions between such models, explain differences in these predictions, recommend priorities for future research concerning the improvement of the accuracy of model predictions and act as a forum for the exchange of ideas, experience and information. (author)

BIOMOVS: An international model validation study

International Nuclear Information System (INIS)

Haegg, C.; Johansson, G.

1987-01-01

BIOMOVS (BIOspheric MOdel Validation Study) is an international study where models used for describing the distribution of radioactive and nonradioactive trace substances in terrestrial and aquatic environments are compared and tested. The main objectives of the study are to compare and test the accuracy of predictions between such models, explain differences in these predictions, recommend priorities for future research concerning the improvement of the accuracy of model predictions and act as a forum for the exchange of ideas, experience and information. (orig.)

STUDY OF TCP PHASE PRECIPITATING IN GH4199 SUPERALLOY

Institute of Scientific and Technical Information of China (English)

T．Cui; Y．S．Zhang; S．W．Guo; L．Wang; H．C．Yang

2004-01-01

The precipitating regulation and mechanism of TCP phase (μ phase and σ phase) are studied, using electron hole number (EHN) theory, phase analysis technology and TEM observation. The results indicate that the EHN in studied alloy is 2.311-2.348 which is higher than that of critical EHN of μ phase precipitate (2.30), so μ phase could precipitate if there is enough thermo-exposition. In contrast, the calculated EHN is less than that of critical EHN of σ phase precipitate (2.52). However the σ phase is also observed by TEM.Enrich of Cr and Mo around γ phase after γ' phase precipitated leads to σ phase precipitated.

Validation Study on the MCC-based Technology

International Nuclear Information System (INIS)

Park, Sungkeun; Lee, Dowhan; Kang, Shincheul; Choi, Hyunwoo; Chai, Jangbom

2006-01-01

KEPRI and M and D Corporation has developed a methodology, called the NEST I (Non-intrusive Evaluation of Stem Thrust), for determining the stem thrust for a Motor Operated Valve (MOV) based on the motor torque and the stem displacement. The motor torque is determined using another method called NEET (Non-intrusive Evaluation of Electric Torque) which uses the voltage and current data from three phases to obtain the motor torque. The stem displacement is obtained from the voltage and current data along with the nameplate information of the motor, actuator and stem. The motor data (voltage, current and coil current) are measured using MOVIDS (Motor Operated Valve Intelligent Diagnostic System). The motor torque is determined using a NEET algorithm and the stem thrust is calculated using the NEST I method. The goal of this testing was to obtain data from operation of a MOV and to compare the actual measured thrust with the thrust calculated using the NEET / NEST I methods and therefore validate the NEET / NEST I methods

Studies on Purification and Coatation of Polyclonal Antibody for Prolactin Solid Phase Radioimmunoassay in Human Serum

International Nuclear Information System (INIS)

El-Bayoumy, A.S.A.; Sallam, Kh.M.; Shafik, H.M.

2012-01-01

The objective of the present study was oriented to produce purified polyclonal antibody to prepare a prolactin solid phase coated tubes radioimmunoassay system. In the present study, production of polyclonal antibodies was carried out through immunization of three healthy white male mature New Zealand rabbits with a highly purified sheep prolactin antigen. The obtained anti-sera was purified using an anion exchange reactive group, diethylamino ethyle (DEAE) covalently linked to Sepharose. The purified polyclonal antibody was used for coating polystyrene tubes. The preparation of 125 I-prolactin tracer was carried out using chloramine-T method. The preparation of standards was performed using assay buffer to cover the range from 2 to 200 ng/ml. The optimization and validation tests of the assay were performed to evaluate the validity of the prepared system. In conclusion, this low cost assay would be used in diagnosis of pituitary dysfunction and diagnosis of infertility in males and females

Studies on Purification and Coatation of Polyclonal Antibody for Prolactin Solid Phase Radioimmunoassay in Human Serum

International Nuclear Information System (INIS)

El-Bayoumy, A.S.A.; Sallam, Kh.M.; Shafik, H.M.

2014-01-01

The objective of the present study was oriented to produce purified polyclonal antibody to prepare a prolactin solid phase coated tubes radioimmunoassay system. In the present study, production of polyclonal antibodies was carried out through immunization of three healthy white male mature New Zealand rabbits with a highly purified sheep prolactin antigen. The obtained anti-sera was purified using an anion exchange reactive group, diethylamino ethyle (DEAE) covalently linked to Sepharose. The purified polyclonal antibody was used for coating polystyrene tubes. The preparation of 125 I-prolactin tracer was carried out using chloramine-T method. The preparation of standards was performed using assay buffer to cover the range from 2 to 200 ng/ml. The optimization and validation tests of the assay were performed to evaluate the validity of the prepared system. In conclusion, this low cost assay would be used in diagnosis of pituitary dysfunction and diagnosis of infertility in males and females.

Validity of the negative binomial multiplicity distribution in case of ultra-relativistic nucleus-nucleus interaction in different azimuthal bins

International Nuclear Information System (INIS)

Ghosh, D.; Deb, A.; Haldar, P.K.; Sahoo, S.R.; Maity, D.

2004-01-01

This work studies the validity of the negative binomial distribution in the multiplicity distribution of charged secondaries in 16 O and 32 S interactions with AgBr at 60 GeV/c per nucleon and 200 GeV/c per nucleon, respectively. The validity of negative binomial distribution (NBD) is studied in different azimuthal phase spaces. It is observed that the data can be well parameterized in terms of the NBD law for different azimuthal phase spaces. (authors)

Validity of worksheet-based guided inquiry and mind mapping for training students’ creative thinking skills

Science.gov (United States)

Susanti, L. B.; Poedjiastoeti, S.; Taufikurohmah, T.

2018-04-01

The purpose of this study is to explain the validity of guided inquiry and mind mapping-based worksheet that has been developed in this study. The worksheet implemented the phases of guided inquiry teaching models in order to train students’ creative thinking skills. The creative thinking skills which were trained in this study included fluency, flexibility, originality and elaboration. The types of validity used in this study included content and construct validity. The type of this study is development research with Research and Development (R & D) method. The data of this study were collected using review and validation sheets. Sources of the data were chemistry lecturer and teacher. The data is the analyzed descriptively. The results showed that the worksheet is very valid and could be used as a learning media with the percentage of validity ranged from 82.5%-92.5%.

External validity of post-stroke interventional gait rehabilitation studies.

Science.gov (United States)

Kafri, Michal; Dickstein, Ruth

2017-01-01

Gait rehabilitation is a major component of stroke rehabilitation, and is supported by extensive research. The objective of this review was to examine the external validity of intervention studies aimed at improving gait in individuals post-stroke. To that end, two aspects of these studies were assessed: subjects' exclusion criteria and the ecological validity of the intervention, as manifested by the intervention's technological complexity and delivery setting. Additionally, we examined whether the target population as inferred from the titles/abstracts is broader than the population actually represented by the reported samples. We systematically researched PubMed for intervention studies to improve gait post-stroke, working backwards from the beginning of 2014. Exclusion criteria, the technological complexity of the intervention (defined as either elaborate or simple), setting, and description of the target population in the titles/abstracts were recorded. Fifty-two studies were reviewed. The samples were exclusive, with recurrent stroke, co-morbidities, cognitive status, walking level, and residency being major reasons for exclusion. In one half of the studies, the intervention was elaborate. Descriptions of participants in the title/abstract in almost one half of the studies included only the diagnosis (stroke or comparable terms) and its stage (acute, subacute, and chronic). The external validity of a substantial number of intervention studies about rehabilitation of gait post-stroke appears to be limited by exclusivity of the samples as well as by deficiencies in ecological validity of the interventions. These limitations are not accurately reflected in the titles or abstracts of the studies.

Cultural Responsive Teaching Readiness Scale Validity and Reliability Study

Directory of Open Access Journals (Sweden)

Kasım KARATAŞ

2017-12-01

Full Text Available The aim of this research is to develop a measurement instrument that will determine the cultural responsive teaching readiness level of teacher candidates. The study group consisted of a total of 231 candidate teachers, of which 83 were males and 148 were females, who were attending their final year of class teacher education programs at various Turkish universities during the 2016-2017 education year. In the first phase, a 33-item draft form was presented to experts to be reviewed. Based on the feedback received, revisions were made and the final scale was applied to a group of 231 candidate teachers. In the analysis of the data obtained as the result of the application, Exploratory Factor Analysis (EFA was performed. The EFA produced 21 items within a two-factor structure as, “Personal Readiness” and “Professional Readiness.” It was observed that the sub-factors were components of the “cultural responsive teaching readiness” dimension, and that the goodness of fit measures obtained as a result of the First and Second Level Confirmatory Factor Analyzes (CFA were high. In addition, reliability coefficients were found to be high as a result of reliability measurements. With the help of these findings, this study concludes that the Cultural Responsive Teaching Readiness scale is both valid and reliable.

Aging and Phase Stability Studies of Alloy 22 FY08 Final Report

Energy Technology Data Exchange (ETDEWEB)

Torres, S G

2008-04-03

This report is a compilation of work done over the past ten years in support of phase stability studies of Alloy 22 for the Yucca Mountain Project and contains information previously published, reported, and referenced. Most sections are paraphrased here for the convenience of readers. Evaluation of the fabrication processes involved in the manufacture of waste containers is important as these processes can have an effect on the metallurgical structure of an alloy. Because material properties such as strength, toughness, aging kinetics and corrosion resistance are all dependent on the microstructure, it is important that prototypes be built and evaluated for processing effects on the performance of the material. Of particular importance are welds, which have an as-cast microstructure with chemical segregation and precipitation of complex phases resulting from the welding process. The work summarized in this report contains information on the effects of fabrication processes such as solution annealing, stress mitigation, heat-to-heat variability, and welding on the kinetics of precipitation, mechanical, and corrosion properties. For a waste package lifetime of thousands of years, it is impossible to test directly in the laboratory the behavior of Alloy 22 under expected repository conditions. The changes that may occur in these materials must be accelerated. For phase stability studies, this is achieved by accelerating the phase transformations by increasing test temperatures above those anticipated in the proposed repository. For these reasons, Alloy 22 characterization specimens were aged at Lawrence Livermore National Laboratory (LLNL) Aging Facilities for times from 1 hour up to 8 years at temperatures ranging from 200-750 C. These data as well as the data from specimens aged at 260 C, 343 C, and 427 C for 100,028 hours at Haynes International will be used for performance confirmation and model validation.

A Study on Guide Sign Validity in Driving Simulator

Directory of Open Access Journals (Sweden)

Wei Zhonghua

2011-12-01

Full Text Available The role of guide sign to inform road user about the information of network is important. How to design and locate guide sign to increase traffic operation efficiency is a key point for traffic engineers. Driving simulator is useful devised to study guide sign in the process and system control. For the purpose of studying guide signs using the tool of driving simulator, guide sign's validity in driving simulator was studied. Results of this experiment are the foundation of further study on guide sign. Simulator calibration procedure for guide sign was set up in this study. Legibility distance as measure of performance was used to evaluate the validity of guide sign in driving simulator. Thirty two participants were recruited. Results indicated legibility distance and speed were inversely related with the method of data mining. Legibility distance and text height of guide sign were positive related. When speed is 20km/h, 30km/h, 40km/h, magnifying power of text height is 4.3, 4.1, 3.8, while guide signs are absolute validity in driving simulator.

Development and Validation of the Transgender Attitudes and Beliefs Scale.

Science.gov (United States)

Kanamori, Yasuko; Cornelius-White, Jeffrey H D; Pegors, Teresa K; Daniel, Todd; Hulgus, Joseph

2017-07-01

In recent years, issues surrounding transgender have garnered media and legal attention, contributing to rapidly shifting views on gender in the U.S. Yet, there is a paucity of data-driven studies on the public's views of transgender identity. This study reports the development and validation of the Transgender Attitudes and Beliefs Scale (TABS). After constructing an initial 96-item pool from consulting experts and existing scales, Phase 1 of the study was launched, involving an exploratory factor analysis of 48 items. The initial factor analysis with 295 participants revealed three factors across 33 items-16 items on interpersonal comfort, 11 on sex/gender beliefs, and 6 on human value. The internal consistency of each factor was high-α = .97 for Factor 1, α = .95 for Factor 2, and α = .94 for Factor 3. A confirmatory factor analysis was conducted in the second phase with an independent sample consisting of 238 participants. The Attitudes Toward Transgender Individual Scale and the Genderism and Transphobia Scale were also included to test for convergent validity, and the Rosenberg Self-Esteem Scale and the short form of the Marlowe-Crowne Social Desirability Scale were utilized to test discriminant validity. Both of the data collection phases employed MTurk, a form of online sampling with increased diversity compared to college student samples and more generalizability to the general U.S. TABS represents an addition to the literature in its ability to capture a more nuanced conceptualization of transgender attitude not found in previous scales.

Assessing Households Preparedness for Earthquakes: An Exploratory Study in the Development of a Valid and Reliable Persian-version Tool.

Science.gov (United States)

Ardalan, Ali; Sohrabizadeh, Sanaz

2016-02-25

Iran is placed among countries suffering from the highest number of earthquake casualties. Household preparedness, as one component of risk reduction efforts, is often supported in quake-prone areas. In Iran, lack of a valid and reliable household preparedness tool was reported by previous disaster studies. This study is aimed to fill this gap by developing a valid and reliable tool for assessing household preparedness in the event of an earthquake.  This survey was conducted through three phases including literature review and focus group discussions with the participation of eight key informants, validity measurements and reliability measurements. Field investigation was completed with the participation of 450 households within three provinces of Iran. Content validity, construct validity, the use of factor analysis; internal consistency using Cronbach's alpha coefficient, and test-retest reliability were carried out to develop the tool.  Based on the CVIs, ranging from 0.80 to 0.100, and exploratory factor analysis with factor loading of more than 0.5, all items were valid. The amount of Cronbach's alpha (0.7) and test-retest examination by Spearman correlations indicated that the scale was also reliable. The final instrument consisted of six categories and 18 questions including actions at the time of earthquakes, nonstructural safety, structural safety, hazard map, communications, drill, and safety skills.  Using a Persian-version tool that is adjusted to the socio-cultural determinants and native language may result in more trustful information on earthquake preparedness. It is suggested that disaster managers and researchers apply this tool in their future household preparedness projects. Further research is needed to make effective policies and plans for transforming preparedness knowledge into behavior.

Feasibility Study on Two-phase Thermosiphon for External Vessel Cooling Application of SFR

Energy Technology Data Exchange (ETDEWEB)

Choi, Jae Young; Song, Sub Lee; Chang, Soon Heung [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2014-05-15

This study shows that ex-vessel cooling by two-phase thermosiphon is feasible for large size of SFR. The result presents that further studies to increase heat transfer on condenser-air and gap is necessary and the experiment should be conducted for the validation. Also, the heat loss through evaporator during normal operation, corrosion, consideration of organic fluid to exclude the poison of mercury should be studied. As the necessity of sodium fast reactor in order to reduce spent fuel, the development of designing sodium fast reactor becomes an issue. Even though there is PDRC and RVACS for the decay heat removal (DHR) system, each system has disadvantage of sodium fire and low performance, respectively. Therefore, to increase the safety of SFR, the new passive safety system design is needed without sodium fire and high performance, which can applied for large SFR. The DHR system using two-phase thermosiphon for external vessel cooling application is suggested in this paper. The proposed design have advantage that there is no structure in reactor vessel, which means no system modification and no sodium fire with perfect isolation. Also, it provide the method to mitigate sodium fire in case of sodium leakage from reactor vessel.

Analytical Method Development and Validation for the Simultaneous Estimation of Abacavir and Lamivudine by Reversed-phase High-performance Liquid Chromatography in Bulk and Tablet Dosage Forms.

Science.gov (United States)

Raees Ahmad, Sufiyan Ahmad; Patil, Lalit; Mohammed Usman, Mohammed Rageeb; Imran, Mohammad; Akhtar, Rashid

2018-01-01

A simple rapid, accurate, precise, and reproducible validated reverse phase high performance liquid chromatography (HPLC) method was developed for the determination of Abacavir (ABAC) and Lamivudine (LAMI) in bulk and tablet dosage forms. The quantification was carried out using Symmetry Premsil C18 (250 mm × 4.6 mm, 5 μm) column run in isocratic way using mobile phase comprising methanol: water (0.05% orthophosphoric acid with pH 3) 83:17 v/v and a detection wavelength of 245 nm and injection volume of 20 μl, with a flow rate of 1 ml/min. In the developed method, the retention times of ABAC and LAMI were found to be 3.5 min and 7.4 min, respectively. The method was validated in terms of linearity, precision, accuracy, limits of detection, limits of quantitation, and robustness in accordance with the International Conference on Harmonization guidelines. The assay of the proposed method was found to be 99% - 101%. The recovery studies were also carried out and mean % recovery was found to be 99% - 101%. The % relative standard deviation from reproducibility was found to be performance liquid chromatography, UV: Ultraviolet, ICH: International Conference on Harmonization, ABAC: Abacavir, LAMI: Lamivudine, HIV: Human immunodeficiency virus, AIDS: Acquired immunodeficiency syndrome, NRTI: Nucleoside reverse transcriptase inhibitors, ARV: Antiretroviral, RSD: Relative standard deviation, RT: Retention time, SD: Standard deviation.

Experimental validation of the Wigner distributions theory of phase-contrast imaging

International Nuclear Information System (INIS)

Donnelly, Edwin F.; Price, Ronald R.; Pickens, David R.

2005-01-01

Recently, a new theory of phase-contrast imaging has been proposed by Wu and Liu [Med. Phys. 31, 2378-2384 (2004)]. This theory, based upon Wigner distributions, provides a much stronger foundation for the evaluation of phase-contrast imaging systems than did the prior theories based upon Fresnel-Kirchhoff diffraction theory. In this paper, we compare results of measurements made in our laboratory of phase contrast for different geometries and tube voltages to the predictions of the Wu and Liu model. In our previous publications, we have used an empirical measurement (the edge enhancement index) to parametrize the degree of phase-contrast effects in an image. While the Wu and Liu model itself does not predict image contrast, it does measure the degree of phase contrast that the system can image for a given spatial frequency. We have found that our previously published experimental results relating phase-contrast effects to geometry and x-ray tube voltage are consistent with the predictions of the Wu and Liu model

[Care with the child's health and validation of an educational technology for riverside families].

Science.gov (United States)

Teixeira, Elizabeth; de Almeida Siqueira, Aldo; da Silva, Joselice Pereira; Lavor, Lília Cunha

2011-01-01

This study aimed to assess the knowledge and ways of caring for the child health 0-5 years between riverine (Phase 1), and to validate an educational technology (Phase 2). It was carried out a descriptive qualitative study. With the mothers, focus groups and content analysis were used, and with judges-specialists and target-public-applied, forms. The study revealed that the concern with the care of a child between the riverine families permeates the adversity daily, with dedication and commitment of these families in maintaining the health of their children. The sensitivity listening of mothers indicated the need for a closer relationship between nursing professionals and family. The validation of the educational technology was convergent, within the parameters considered adequate.

A numerical study of steady-state two-phase flow in porous media

Energy Technology Data Exchange (ETDEWEB)

Knudsen, Henning Arendt

2002-07-01

Two-phase flow in porous media means the simultaneous flow of two phases, say two liquids, e.g., oil and water. This flow is restrained to be within a porous medium. For example sandstone and limestone are typical porous stones that can contain oil and gas in nature. In the extraction of oil from reservoirs, oil is usually displaced by water. So on a large scale we can consider it to be a displacement process. However, on pore scale the ''mix'' and flow processes are complicated. Idealistically, one might consider the search for truth a sufficient motivation for work in this field. Nevertheless, from an economic and technological point of view, enhanced oil recovery is the main motivation for the study of two-phase flow in porous media. Luckily, there are additional systems in real world that falls into this category. One such system is the flow of water and pollutants in aquifers. General knowledge in the field might be beneficial for preserving ground water reserves in the future. In the laboratory one often encounters artificially made porous media. For example glass beads between two glass plates. Therein, one of the phases flowing may be a mixture of glycerol and water. The other phase can be air which then is the non-wetting phase; air does not wet glass. It can also be silicone oil, and in that case the water/glycerol is normally the nonwetting phase. There are other possibilities. In general, laboratory studies are performed on systems on pore scale. The flow properties on the various length scales found in flow systems in nature depend on these properties on pore scale. The so-called upscaling problem concerns how to relate pore scale properties with properties on larger scales. The scope of this thesis is the study of properties on pore scale. The upscaling problem, which is a large research field in itself, is thus outside the scope of this thesis. The results of Paper 3 is an exception since they may infer also to larger scales than

Distress Tolerance Scale: A Study of Reliability and Validity

Directory of Open Access Journals (Sweden)

Ahmet Emre SARGIN

2012-11-01

Full Text Available Objective: Distress Tolerance Scale (DTS is developed by Simons and Gaher in order to measure individual differences in the capacity of distress tolerance.The aim of this study is to assess the reliability and validity of the Turkish version of DTS. Method: One hundred and sixty seven university students (male=66, female=101 participated in this study. Beck Anxiety Inventory (BAI, State-trait Anxiety Inventory (STAI and Discomfort Intolerance Scale (DIS were used to determine the criterion validity. Construct validity was evaluated with factor analysis after the Kaiser-Meyer-Olkin (KMO and Barlett test had been performed. To assess the test-retest reliability, the scale was re-applied to 79 participants six weeks later. Results: To assess construct validity, factor analyses were performed using varimax principal components analysis with varimax rotation. While there were factors in the original study, our factor analysis resulted in three factors. Cronbach’s alpha coefficients for the entire scale and tolerance, regulation, self-efficacy subscales were .89, .90, .80 and .64 respectively. There were correlations at the level of 0.01 between the Trait Anxiety Inventory of STAI and BAI, and all the subscales of DTS and also between the State Anxiety Inventory and regulation subscale. Both of the subscales of DIS were correlated with the entire subscale and all the subscales except regulation at the level of 0.05.Test-retest reliability was statistically significant at the level of 0.01. Conclusion: Analysis demonstrated that DTS had a satisfactory level of reliability and validity in Turkish university students.

40 CFR 152.93 - Citation of a previously submitted valid study.

Science.gov (United States)

2010-07-01

... Data Submitters' Rights § 152.93 Citation of a previously submitted valid study. An applicant may demonstrate compliance for a data requirement by citing a valid study previously submitted to the Agency. The... the original data submitter, the applicant may cite the study only in accordance with paragraphs (b...

Etude sur la prédiction de l'inversion de phase Phase Inversion Behavior for Liquid Dispersions

Directory of Open Access Journals (Sweden)

Decarre S.

2006-12-01

Full Text Available En écoulement diphasique eau-huile dans lequel une des phases est dispersée dans l'autre, il peut se produire sous certaine condition d'écoulement une inversion de phase, la phase continue devenant dispersée. Ce phénomène, qui contrôle la nature de la phase mouillant la paroi de la conduite dans laquelle s'écoulent les phases, a des conséquences importantes sur la corrosion et sur la perte de charge. Nous présentons un modèle d'inversion, basé sur une approche thermodynamique, valable pour tous les régimes d'écoulement. Les données expérimentales utilisées pour la validation du modèle sont issues d'une étude bibliographique. En écoulement laminaire, cette approche conduit à des résultats similaires à ceux du modèle de Yeh. Pour la plupart des données disponibles, ce modèle prédit bien la fraction critique pour laquelle l'inversion de phase se produit. In two phase oil-water dispersed flow, a phase inversion may occur whereby the continuous phase becomes dispersed. This phenomenon which controls the nature of the phase in contact with the pipe has a great importance on the corrosion and on the pressure drop. A model for the phase inversion is presented, it is based on a thermodynamic approach, and it is valid for all flow regimes. Experimental data from the litterature are used to validate the model. In laminar flow, this approach gives similar results to those obtained by Yeh. For most data, the model agrees well with the experimental data.

Turkish Version of Kolcaba's Immobilization Comfort Questionnaire: A Validity and Reliability Study.

Science.gov (United States)

Tosun, Betül; Aslan, Özlem; Tunay, Servet; Akyüz, Aygül; Özkan, Hüseyin; Bek, Doğan; Açıksöz, Semra

2015-12-01

The purpose of this study was to determine the validity and reliability of the Turkish version of the Immobilization Comfort Questionnaire (ICQ). The sample used in this methodological study consisted of 121 patients undergoing lower extremity arthroscopy in a training and research hospital. The validity study of the questionnaire assessed language validity, structural validity and criterion validity. Structural validity was evaluated via exploratory factor analysis. Criterion validity was evaluated by assessing the correlation between the visual analog scale (VAS) scores (i.e., the comfort and pain VAS scores) and the ICQ scores using Spearman's correlation test. The Kaiser-Meyer-Olkin coefficient and Bartlett's test of sphericity were used to determine the suitability of the data for factor analysis. Internal consistency was evaluated to determine reliability. The data were analyzed with SPSS version 15.00 for Windows. Descriptive statistics were presented as frequencies, percentages, means and standard deviations. A p value ≤ .05 was considered statistically significant. A moderate positive correlation was found between the ICQ scores and the VAS comfort scores; a moderate negative correlation was found between the ICQ and the VAS pain measures in the criterion validity analysis. Cronbach α values of .75 and .82 were found for the first and second measurements, respectively. The findings of this study reveal that the ICQ is a valid and reliable tool for assessing the comfort of patients in Turkey who are immobilized because of lower extremity orthopedic problems. Copyright © 2015. Published by Elsevier B.V.

Multi Frequency Phase Fluorimetry (MFPF) for Oxygen Partial Pressure Measurement: Ex Vivo Validation by Polarographic Clark-Type Electrode

Science.gov (United States)

Boehme, Stefan; Duenges, Bastian; Klein, Klaus U.; Hartwich, Volker; Mayr, Beate; Consiglio, Jolanda; Baumgardner, James E.; Markstaller, Klaus; Basciani, Reto; Vogt, Andreas

2013-01-01

Background Measurement of partial pressure of oxygen (PO2) at high temporal resolution remains a technological challenge. This study introduces a novel PO2 sensing technology based on Multi-Frequency Phase Fluorimetry (MFPF). The aim was to validate MFPF against polarographic Clark-type electrode (CTE) PO2 measurements. Methodology/Principal Findings MFPF technology was first investigated in N = 8 anaesthetised pigs at FIO2 of 0.21, 0.4, 0.6, 0.8 and 1.0. At each FIO2 level, blood samples were withdrawn and PO2 was measured in vitro with MFPF using two FOXY-AL300 probes immediately followed by CTE measurement. Secondly, MFPF-PO2 readings were compared to CTE in an artificial circulatory setup (human packed red blood cells, haematocrit of 30%). The impacts of temperature (20, 30, 40°C) and blood flow (0.8, 1.6, 2.4, 3.2, 4.0 L min−1) on MFPF-PO2 measurements were assessed. MFPF response time in the gas- and blood-phase was determined. Porcine MFPF-PO2 ranged from 63 to 749 mmHg; the corresponding CTE samples from 43 to 712 mmHg. Linear regression: CTE = 15.59+1.18*MFPF (R2 = 0.93; PPO2 ranged from 20 to 567 mmHg and CTE samples from 11 to 575 mmHg. Linear regression: CTE = −8.73+1.05*MFPF (R2 = 0.99; PPO2 due to variations of temperature were less than 6 mmHg (range 0–140 mmHg) and less than 35 mmHg (range 140–750 mmHg); differences due to variations in blood flow were less than 15 mmHg (all P-values>0.05). MFPF response-time (monoexponential) was 1.48±0.26 s for the gas-phase and 1.51±0.20 s for the blood-phase. Conclusions/Significance MFPF-derived PO2 readings were reproducible and showed excellent correlation and good agreement with Clark-type electrode-based PO2 measurements. There was no relevant impact of temperature and blood flow upon MFPF-PO2 measurements. The response time of the MFPF FOXY-AL300 probe was adequate for real-time sensing in the blood phase. PMID:23565259

Fatigue Equivalent Stress State Approach Validation in Non-conservative Criteria: a Comparative Study

Directory of Open Access Journals (Sweden)

Kévin Martial Tsapi Tchoupou

Full Text Available Abstract This paper is concerned with the fatigue prediction models for estimating the multiaxial fatigue limit. An equivalent loading approach with zero out-of-phase angles intended for fatigue limit evaluation under multiaxial loading is used. Based on experimental data found in literatures, the equivalent stress is validated in Crossland and Sines criteria and predictions compared to the predictions of existing multiaxial fatigue; results over 87 experimental items show that the equivalent stress approach is very efficient.

Can we forget the Mini-Mental State Examination? A systematic review of the validity of cognitive screening instruments within one month after stroke.

Science.gov (United States)

Van Heugten, Caroline M; Walton, L; Hentschel, U

2015-07-01

To review systematically studies investigating the convergent, criterion, and predictive validity of multi-domain cognitive screening instruments in the first four weeks after stroke. Electronic databases (Pubmed, PsycINFO, CINAHL, Embase) were searched until June 2014. Studies concerning screening for cognitive dysfunction in stroke patients using multi-domain instruments, within four weeks postinfarct or haemorrhagic stroke, using tests taking no longer than one hour. Convergent, criterion, and predictive validity were examined. A total of 51 studies investigating 16 cognitive screening instruments were identified. None of the instruments covered all of the most affected cognitive domains. Only one study investigated the convergent validity of a multi-domain test during the (sub)acute phase after stroke. A total of 15 studies examined the criterion validity of cognitive measurements during the acute phase after stroke. The Montreal Cognitive Assessment and Higher Cortical Function Deficit Test had good criterion validity. A total of 24 studies examined the predictive ability of multi-domain cognitive instruments applied in the acute phase after stroke. The Cognistat, Montreal Cognitive Assessment, and Functional Independence Measure-cognitive showed good predictive validity. The Mini-Mental State Examination is the most widely used cognitive screening instrument, but shows insufficient criterion validity. None of the existing instruments fulfils all criteria. The Montreal Cognitive Assessment is the best candidate at present, provided items measuring speed of information processing are added, and further studies investigating the optimal cut-offs are conducted. © The Author(s) 2014.

A study on two phase flows of linear compressors for the prediction of refrigerant leakage

International Nuclear Information System (INIS)

Hwang, Il Sun; Lee, Young Lim; Oh, Won Sik; Park, Kyeong Bae

2015-01-01

Usage of linear compressors is on the rise due to their high efficiency. In this paper, leakage of a linear compressor has been studied through numerical analysis and experiments. First, nitrogen leakage for a stagnant piston with fixed cylinder pressure as well as for a moving piston with fixed cylinder pressure was analyzed to verify the validity of the two-phase flow analysis model. Next, refrigerant leakage of a linear compressor in operation was finally predicted through 3-dimensional unsteady, two phase flow CFD (Computational fluid dynamics). According to the research results, the numerical analyses for the fixed cylinder pressure models were in good agreement with the experimental results. The refrigerant leakage of the linear compressor in operation mainly occurred through the oil exit and the leakage became negligible after about 0.4s following operation where the leakage became lower than 2.0x10 -4 kg/s.

Exploring the validity and statistical utility of a racism scale among Black men who have sex with men: a pilot study.

Science.gov (United States)

Smith, William Pastor

2013-09-01

The primary purpose of this two-phased study was to examine the structural validity and statistical utility of a racism scale specific to Black men who have sex with men (MSM) who resided in the Washington, DC, metropolitan area and Baltimore, Maryland. Phase I involved pretesting a 10-item racism measure with 20 Black MSM. Based on pretest findings, the scale was adapted into a 21-item racism scale for use in collecting data on 166 respondents in Phase II. Exploratory factor analysis of the 21-item racism scale resulted in a 19-item, two-factor solution. The two factors or subscales were the following: General Racism and Relationships and Racism. Confirmatory factor analysis was used in testing construct validity of the factored racism scale. Specifically, the two racism factors were combined with three homophobia factors into a confirmatory factor analysis model. Based on a summary of the fit indices, both comparative and incremental were equal to .90, suggesting an adequate convergence of the racism and homophobia dimensions into a single social oppression construct. Statistical utility of the two racism subscales was demonstrated when regression analysis revealed that the gay-identified men versus bisexual-identified men in the sample were more likely to experience increased racism within the context of intimate relationships and less likely to be exposed to repeated experiences of general racism. Overall, the findings in this study highlight the importance of continuing to explore the psychometric properties of a racism scale that accounts for the unique psychosocial concerns experienced by Black MSM.

Input Calibration and Validation of RELAP5 Against CIRCUS-IV Single Channel Tests on Natural Circulation Two-Phase Flow Instability

Directory of Open Access Journals (Sweden)

Viet-Anh Phung

2015-01-01

Full Text Available RELAP5 is a system thermal-hydraulic code that is used to perform safety analysis on nuclear reactors. Since the code is based on steady state, two-phase flow regime maps, there is a concern that RELAP5 may provide significant errors for rapid transient conditions. In this work, the capability of RELAP5 code to predict the oscillatory behavior of a natural circulation driven, two-phase flow at low pressure is investigated. The simulations are compared with a series of experiments that were performed in the CIRCUS-IV facility at the Delft University of Technology. For this purpose, we developed a procedure for calibration of the input and code validation. The procedure employs (i multiple parameters measured in different regimes, (ii independent consideration of the subsections of the loop, and (iii assessment of importance of the uncertain input parameters. We found that predicted system parameters are less sensitive to variations of the uncertain input and boundary conditions in high frequency oscillations regime. It is shown that calculation results overlap experimental values, except for the high frequency oscillations regime where the maximum inlet flow rate was overestimated. This finding agrees with the idea that steady state, two-phase flow regime maps might be one of the possible reasons for the discrepancy in case of rapid transients in two-phase systems.

Active debris removal GNC challenges over design and required ground validation

Science.gov (United States)

Colmenarejo, Pablo; Avilés, Marcos; di Sotto, Emanuele

2015-06-01

Because of the exponential growth of space debris, the access to space in the medium-term future is considered as being seriously compromised, particularly within LEO polar Sun-synchronous orbits and within geostationary orbits. The active debris removal (ADR) application poses new and challenging requirements on: first, the new required Guidance, Navigation and Control (GNC) technologies and, second, how to validate these new technologies before being applied in real missions. There is no doubt about the strong safety and collision risk aspects affecting the real operational ADR missions. But it shall be considered that even ADR demonstration missions will be affected by significant risk of collision during the demonstration, and that the ADR GNC systems/technologies to be used shall be well mature before using/demonstrating them in space. Specific and dedicated on-ground validation approaches, techniques and facilities are mandatory. The different ADR techniques can be roughly catalogued in three main groups (rigid capture, non-rigid capture and contactless). All of them have a strong impact on the GNC system of the active vehicle during the capture/proximity phase and, particularly, during the active vehicle/debris combo control phase after capture and during the de-orbiting phase. The main operational phases on an ADR scenario are: (1) ground controlled phase (ADR vehicle and debris are far), (2) fine orbit synchronization phase (ADR vehicle to reach debris ±V-bar), (3) short range phase (along track distance reduction till 10-100 s of metres), (4) terminal approach/capture phase and (5) de-orbiting. While phases 1-3 are somehow conventional and already addressed in detail during past/on-going studies related to rendezvous and/or formation flying, phases 4-5 are very specific and not mature in terms of GNC needed technologies and HW equipment. GMV is currently performing different internal activities and ESA studies/developments related to ADR mission, GNC and

Generalized Phase Contrast

CERN Document Server

Glückstad, Jesper

2009-01-01

Generalized Phase Contrast elevates the phase contrast technique not only to improve phase imaging but also to cross over and interface with diverse and seemingly disparate fields of contemporary optics and photonics. This book presents a comprehensive introduction to the Generalized Phase Contrast (GPC) method including an overview of the range of current and potential applications of GPC in wavefront sensing and phase imaging, structured laser illumination and image projection, optical trapping and manipulation, and optical encryption and decryption. The GPC method goes further than the restrictive assumptions of conventional Zernike phase contrast analysis and achieves an expanded range of validity beyond weak phase perturbations. The generalized analysis yields design criteria for tuning experimental parameters to achieve optimal performance in terms of accuracy, fidelity and light efficiency. Optimization can address practical issues, such as finding an optimal spatial filter for the chosen application, ...

Point-to-Point! Validation of the Small Aircraft Transportation System Higher Volume Operations Concept

Science.gov (United States)

Williams, Daniel M.

2006-01-01

Described is the research process that NASA researchers used to validate the Small Aircraft Transportation System (SATS) Higher Volume Operations (HVO) concept. The four phase building-block validation and verification process included multiple elements ranging from formal analysis of HVO procedures to flight test, to full-system architecture prototype that was successfully shown to the public at the June 2005 SATS Technical Demonstration in Danville, VA. Presented are significant results of each of the four research phases that extend early results presented at ICAS 2004. HVO study results have been incorporated into the development of the Next Generation Air Transportation System (NGATS) vision and offer a validated concept to provide a significant portion of the 3X capacity improvement sought after in the United States National Airspace System (NAS).

Phase controlled rectifier study

International Nuclear Information System (INIS)

Bronner, G.; Murray, J.G.

1976-03-01

This report introduces the results of an engineering study incorporating a computer program to determine the transient and steady-state voltage and current wave shapes for a 12-pulse rectifier system. Generally, rectifier engineering studies are completed by making simplified assumptions and neglecting many circuit parameters. The studies incorporate the 3-phase AC parameters including nonlinear source or generator, 3-winding transformer impedances, and shunt and series capacitors. It includes firing angle control, and DC filter circuits with inductive loads

Discomfort Intolerance Scale: A Study of Reliability and Validity

Directory of Open Access Journals (Sweden)

Kadir ÖZDEL

2012-03-01

Full Text Available Objective: Discomfort Intolerance Scale was developed by Norman B. Schmidt et al. to assess the individual differences of capacity to withstand physical perturbations or uncomfortable bodily states (2006. The aim of this study is to investigate the validity and reliability of Discomfort Intolerance Scale-Turkish Version (RDÖ. Method: From two different universities, total of 225 students (male=167, female=58 were participated in this study. In order to determine the criterion validity, Beck Anxiety Inventory (BAI and State-Trait Anxiety Inventory (STAI were used. Construct validity was evaluated by factor analysis after the Kaiser-Meyer-Olkin (KMO and Barlett test had been performed. To assess the test-retest reliability the scale was re-applied to 54 participants 6 weeks later. Results: To assess construct validity of DIS, factor analyses were performed using varimax principal components analysis with varimax rotation. The factor analysis resulted in two factors named “discomfort (in tolerance” and “discomfort avoidance”. The Cronbach’s alpha coefficient for the entire scale, discomfort-(intolerance subscale, discomfortavoidance subscale were, .592, .670, .600 respectively. Correlations between two factors of DIS, discomfort intolerance and discomfort avoidance, and Trait Anxiety Inventory of STAI (State-Trait Anxiety Inventory were statistically significant at the level of 0.05. Test-retest reliability was statistically significant at the level of 0.01. Conclusion: Analysis demonstrated that DIS had a satisfactory level of reliability and validity in Turkish university students.

Replication of LDL GWAs hits in PROSPER/PHASE as validation for future (pharmaco)genetic analyses

LENUS (Irish Health Repository)

Trompet, Stella

2011-10-06

Abstract Background The PHArmacogenetic study of Statins in the Elderly at risk (PHASE) is a genome wide association study in the PROspective Study of Pravastatin in the Elderly at risk for vascular disease (PROSPER) that investigates the genetic variation responsible for the individual variation in drug response to pravastatin. Statins lower LDL-cholesterol in general by 30%, however not in all subjects. Moreover, clinical response is highly variable and adverse effects occur in a minority of patients. In this report we first describe the rationale of the PROSPER\\/PHASE project and second show that the PROSPER\\/PHASE study can be used to study pharmacogenetics in the elderly. Methods The genome wide association study (GWAS) was conducted using the Illumina 660K-Quad beadchips following manufacturer\\'s instructions. After a stringent quality control 557,192 SNPs in 5,244 subjects were available for analysis. To maximize the availability of genetic data and coverage of the genome, imputation up to 2.5 million autosomal CEPH HapMap SNPs was performed with MACH imputation software. The GWAS for LDL-cholesterol is assessed with an additive linear regression model in PROBABEL software, adjusted for age, sex, and country of origin to account for population stratification. Results Forty-two SNPs reached the GWAS significant threshold of p = 5.0e-08 in 5 genomic loci (APOE\\/APOC1; LDLR; FADS2\\/FEN1; HMGCR; PSRC1\\/CELSR5). The top SNP (rs445925, chromosome 19) with a p-value of p = 2.8e-30 is located within the APOC1 gene and near the APOE gene. The second top SNP (rs6511720, chromosome 19) with a p-value of p = 5.22e-15 is located within the LDLR gene. All 5 genomic loci were previously associated with LDL-cholesterol levels, no novel loci were identified. Replication in WOSCOPS and CARE confirmed our results. Conclusion With the GWAS in the PROSPER\\/PHASE study we confirm the previously found genetic associations with LDL-cholesterol levels. With this proof

Analytical method development and validation of simultaneous estimation of rabeprazole, pantoprazole, and itopride by reverse-phase high-performance liquid chromatography

Directory of Open Access Journals (Sweden)

Senthamil Selvan Perumal

2014-12-01

Full Text Available A simple, selective, rapid, and precise reverse-phase high-performance liquid chromatography (RP-HPLC method for the simultaneous estimation of rabeprazole (RP, pantoprazole (PP, and itopride (IP has been developed. The compounds were well separated on a Phenomenex C18 (Luna column (250 mm × 4.6 mm, dp = 5 μm with C18 guard column (4 mm × 3 mm × 5 μm with a mobile phase consisting of buffer containing 10 mM potassium dihydrogen orthophosphate (adjusted to pH 6.8: acetonitrile (70:30 v/v at a flow rate of 1.0 mL/min and ultraviolet detection at 288 nm. The retention time of RP, PP, and IP were 5.35, 7.92, and 11.16 minutes, respectively. Validation of the proposed method was carried out according to International Conference on Harmonisation (ICH guidelines. Linearity range was obtained for RP, PP, and IP over the concentration range of 2.5–25, 1–30, and 3–35 μg/mL and the r2 values were 0.994, 0.978, and 0.991, respectively. The calculated limit of detection (LOD values were 1, 0.3, and 1 μg/mL and limit of quantitation (LOQ values were 2.5, 1, and 3 μg/mL for RP, PP, and IP correspondingly. Thus, the current study showed that the developed reverse-phase liquid chromatography method is sensitive and selective for the estimation of RP, PP, and IP in combined dosage form.

Analytical method development and validation of simultaneous estimation of rabeprazole, pantoprazole, and itopride by reverse-phase high-performance liquid chromatography.

Science.gov (United States)

Perumal, Senthamil Selvan; Ekambaram, Sanmuga Priya; Raja, Samundeswari

2014-12-01

A simple, selective, rapid, and precise reverse-phase high-performance liquid chromatography (RP-HPLC) method for the simultaneous estimation of rabeprazole (RP), pantoprazole (PP), and itopride (IP) has been developed. The compounds were well separated on a Phenomenex C 18 (Luna) column (250 mm × 4.6 mm, dp = 5 μm) with C 18 guard column (4 mm × 3 mm × 5 μm) with a mobile phase consisting of buffer containing 10 mM potassium dihydrogen orthophosphate (adjusted to pH 6.8): acetonitrile (70:30 v/v) at a flow rate of 1.0 mL/min and ultraviolet detection at 288 nm. The retention time of RP, PP, and IP were 5.35, 7.92, and 11.16 minutes, respectively. Validation of the proposed method was carried out according to International Conference on Harmonisation (ICH) guidelines. Linearity range was obtained for RP, PP, and IP over the concentration range of 2.5-25, 1-30, and 3-35 μg/mL and the r 2 values were 0.994, 0.978, and 0.991, respectively. The calculated limit of detection (LOD) values were 1, 0.3, and 1 μg/mL and limit of quantitation (LOQ) values were 2.5, 1, and 3 μg/mL for RP, PP, and IP correspondingly. Thus, the current study showed that the developed reverse-phase liquid chromatography method is sensitive and selective for the estimation of RP, PP, and IP in combined dosage form. Copyright © 2014. Published by Elsevier B.V.

CANDU radiotoxicity inventories estimation: A calculated experiment cross-check for data verification and validation

International Nuclear Information System (INIS)

Pavelescu, Alexandru Octavian; Cepraga, Dan Gabriel

2007-01-01

This paper is related to the Clearance Potential Index, Ingestion and Inhalation Hazard Factors of the nuclear spent fuel and radioactive wastes. This study required a complex activity that consisted of various phases such us: the acquisition, setting up, validation and application of procedures, codes and libraries. The paper reflects the validation phase of this study. Its objective was to compare the measured inventories of selected actinide and fission products radionuclides in an element from a Pickering CANDU reactor with inventories predicted using a recent version of the ORIGEN-ARP from SCALE 5 coupled with the time dependent cross sections library, CANDU 28.lib, produced by the sequence SAS2H of SCALE 4.4a. In this way, the procedures, codes and libraries for the characterization of radioactive material in terms of radioactive inventories, clearance, and biological hazard factors are being qualified and validated, in support for the safety management of the radioactive wastes. (authors)

Test of Creative Imagination: Validity and Reliability Study

Science.gov (United States)

Gundogan, Aysun; Ari, Meziyet; Gonen, Mubeccel

2013-01-01

The purpose of this study was to investigate validity and reliability of the test of creative imagination. This study was conducted with the participation of 1000 children, aged between 9-14 and were studying in six primary schools in the city center of Denizli Province, chosen by cluster ratio sampling. In the study, it was revealed that the…

Development and validation of an instrument to measure nurse educator perceived confidence in clinical teaching.

Science.gov (United States)

Nguyen, Van N B; Forbes, Helen; Mohebbi, Mohammadreza; Duke, Maxine

2017-12-01

Teaching nursing in clinical environments is considered complex and multi-faceted. Little is known about the role of the clinical nurse educator, specifically the challenges related to transition from clinician, or in some cases, from newly-graduated nurse to that of clinical nurse educator, as occurs in developing countries. Confidence in the clinical educator role has been associated with successful transition and the development of role competence. There is currently no valid and reliable instrument to measure clinical nurse educator confidence. This study was conducted to develop and psychometrically test an instrument to measure perceived confidence among clinical nurse educators. A multi-phase, multi-setting survey design was used. A total of 468 surveys were distributed, and 363 were returned. Data were analyzed using exploratory and confirmatory factor analyses. The instrument was successfully tested and modified in phase 1, and factorial validity was subsequently confirmed in phase 2. There was strong evidence of internal consistency, reliability, content, and convergent validity of the Clinical Nurse Educator Skill Acquisition Assessment instrument. The resulting instrument is applicable in similar contexts due to its rigorous development and validation process. © 2017 The Authors. Nursing & Health Sciences published by John Wiley & Sons Australia, Ltd.

Options Study - Phase II

Energy Technology Data Exchange (ETDEWEB)

R. Wigeland; T. Taiwo; M. Todosow; W. Halsey; J. Gehin

2010-09-01

The Options Study has been conducted for the purpose of evaluating the potential of alternative integrated nuclear fuel cycle options to favorably address the issues associated with a continuing or expanding use of nuclear power in the United States. The study produced information that can be used to inform decisions identifying potential directions for research and development on such fuel cycle options. An integrated nuclear fuel cycle option is defined in this study as including all aspects of the entire nuclear fuel cycle, from obtaining natural resources for fuel to the ultimate disposal of used nuclear fuel (UNF) or radioactive wastes. Issues such as nuclear waste management, especially the increasing inventory of used nuclear fuel, the current uncertainty about used fuel disposal, and the risk of nuclear weapons proliferation have contributed to the reluctance to expand the use of nuclear power, even though it is recognized that nuclear power is a safe and reliable method of producing electricity. In this Options Study, current, evolutionary, and revolutionary nuclear energy options were all considered, including the use of uranium and thorium, and both once-through and recycle approaches. Available information has been collected and reviewed in order to evaluate the ability of an option to clearly address the challenges associated with the current implementation and potential expansion of commercial nuclear power in the United States. This Options Study is a comprehensive consideration and review of fuel cycle and technology options, including those for disposal, and is not constrained by any limitations that may be imposed by economics, technical maturity, past policy, or speculated future conditions. This Phase II report is intended to be used in conjunction with the Phase I report, and much information in that report is not repeated here, although some information has been updated to reflect recent developments. The focus in this Options Study was to

Validation of CryoSat-2 Performance over Arctic Sea Ice

DEFF Research Database (Denmark)

Di Bella, Alessandro; Skourup, Henriette; Bouffard, J.

The main objective of this work is to validate CryoSat-2 (CS2) SARIn performance over sea ice by use of airborne laser altimetry data obtained during the CryoVEx 2012 campaign. A study by [1] has shown that the extra information from the CS2 SARIn mode increases the number of valid sea surface...... to validate the sea ice freeboard obtained by processing CS2 SARIn level 1b waveforms. The possible reduction in the random freeboard uncertainty is investigated comparing two scenarios, i.e. a SAR-like and a SARIn acquisition. It is observed that using the extra phase information, CS2 is able to detect leads...... height estimates which are usually discarded in the SAR mode due to snagging of the radar signal. As the number of valid detected leads increases, the uncertainty of the freeboard heights decreases. In this study, the snow freeboard heights estimated using data from the airborne laser scanner are used...

A validated HPTLC method for determination of terbutaline sulfate in biological samples: Application to pharmacokinetic study

OpenAIRE

Faiyazuddin, Md.; Rauf, Abdul; Ahmad, Niyaz; Ahmad, Sayeed; Iqbal, Zeenat; Talegaonkar, Sushma; Bhatnagar, Aseem; Khar, Roop K.; Ahmad, Farhan J.

2011-01-01

Terbutaline sulfate (TBS) was assayed in biological samples by validated HPTLC method. Densitometric analysis of TBS was carried out at 366 nm on precoated TLC aluminum plates with silica gel 60F254 as a stationary phase and chloroform–methanol (9.0:1.0, v/v) as a mobile phase. TBS was well resolved at RF 0.34 ± 0.02. In all matrices, the calibration curve appeared linear (r2 ⩾ 0.9943) in the tested range of 100–1000 ng spot−1 with a limit of quantification of 18.35 ng spot−1. Drug recovery f...

Dynamic Transcriptional Regulation of Fis in Salmonella During the Exponential Phase.

Science.gov (United States)

Wang, Hui; Wang, Lei; Li, Ping; Hu, Yilang; Zhang, Wei; Tang, Bo

2015-12-01

Fis is one of the most important global regulators and has attracted extensive research attention. Many studies have focused on comparing the Fis global regulatory networks for exploring Fis function during different growth stages, such as the exponential and stationary stages. Although the Fis protein in bacteria is mainly expressed in the exponential phase, the dynamic transcriptional regulation of Fis during the exponential phase remains poorly understood. To address this question, we used RNA-seq technology to identify the Fis-regulated genes in the S. enterica serovar Typhimurium during the early exponential phase, and qRT-PCR was performed to validate the transcriptional data. A total of 1495 Fis-regulated genes were successfully identified, including 987 Fis-repressed genes and 508 Fis-activated genes. Comparing the results of this study with those of our previous study, we found that the transcriptional regulation of Fis was diverse during the early- and mid-exponential phases. The results also showed that the strong positive regulation of Fis on Salmonella pathogenicity island genes in the mid-exponential phase transitioned into insignificant effect in the early exponential phase. To validate these results, we performed a cell infection assay and found that Δfis only exhibited a 1.49-fold decreased capacity compared with the LT2 wild-type strain, indicating a large difference from the 6.31-fold decrease observed in the mid-exponential phase. Our results provide strong evidence for a need to thoroughly understand the dynamic transcriptional regulation of Fis in Salmonella during the exponential phase.

[Translation, cultural adaptation and validation of the Salt Knowledge Questionnaire to the Spanish language].

Science.gov (United States)

Quinteros-Reyes, C; Marcionelli-Sandhaus, T; Mayta-Tristán, P

2017-11-03

In order to reduce salt consumption in Spanish speaking countries it is necessary to know the level of salt knowledge in the population. However, there are no tools in Spanish to measure salt knowledge, but the only valid tool of measurement is the 'Salt Knowledge Questionnaire' (SKQ) developed in Australia, in English. A validation study was conducted in three phases: (Phase1) Translation of the original Australian version into Spanish; (Phase2) Cultural adaptation based on a Spanish-speaking population such as Peru and following criteria used in the development of the original questionnaire which was evaluated by a panel of experts; (Phase3) Construct validity by comparing the scores of three groups (experts, medical students and non-experts) and reliability by performing a test retest. The translation of the SKQ into Spanish maintained a semantic equivalence with the original questionnaire and a panel of experts accepted the cultural adaptation. The SKQ enables discrimination between those who know and those who do not because differences of scores were found between the group of experts, students and non-experts (P.05). The SKQ questionnaire in Spanish is valid, reliable and is a suitable first tool to measure knowledge about salt in the Spanish language. It is considered possible to adapt it culturally to the Spanish-speaking country that wishes to use it. Copyright © 2017 SEH-LELHA. Publicado por Elsevier España, S.L.U. All rights reserved.

Can We Study Autonomous Driving Comfort in Moving-Base Driving Simulators? A Validation Study.

Science.gov (United States)

Bellem, Hanna; Klüver, Malte; Schrauf, Michael; Schöner, Hans-Peter; Hecht, Heiko; Krems, Josef F

2017-05-01

To lay the basis of studying autonomous driving comfort using driving simulators, we assessed the behavioral validity of two moving-base simulator configurations by contrasting them with a test-track setting. With increasing level of automation, driving comfort becomes increasingly important. Simulators provide a safe environment to study perceived comfort in autonomous driving. To date, however, no studies were conducted in relation to comfort in autonomous driving to determine the extent to which results from simulator studies can be transferred to on-road driving conditions. Participants ( N = 72) experienced six differently parameterized lane-change and deceleration maneuvers and subsequently rated the comfort of each scenario. One group of participants experienced the maneuvers on a test-track setting, whereas two other groups experienced them in one of two moving-base simulator configurations. We could demonstrate relative and absolute validity for one of the two simulator configurations. Subsequent analyses revealed that the validity of the simulator highly depends on the parameterization of the motion system. Moving-base simulation can be a useful research tool to study driving comfort in autonomous vehicles. However, our results point at a preference for subunity scaling factors for both lateral and longitudinal motion cues, which might be explained by an underestimation of speed in virtual environments. In line with previous studies, we recommend lateral- and longitudinal-motion scaling factors of approximately 50% to 60% in order to obtain valid results for both active and passive driving tasks.

Contribution to the dynamical study of gas-liquid two-phase flows

International Nuclear Information System (INIS)

Lewi, Joseph.

1975-01-01

A single system of equations valid for two-phase flows at any time and anywhere was searched for. The mathematical theory of distributions was used. The results obtained was applied to the turbulent flow of an emulsion in a canal of constant section. It is shown that the use of distribution conservation equations makes it possible to determine the shapes of the mean velocity profiles, to obtain a relation between the friction coefficient and a Reynolds number introduced in a logical way, and to express the total pressure drop in the canal. Three experiments were carried out to compare the performance of various optical methods used for displaying bubble liquid-gas flows, and, within the limits of these methods, to study the interaction between the bubbles and the sensible end of variable impedance probe, and the granulometry of the emulsion in the vicinity of the probe [fr

Development and validation of the Patient Benefit Index for peripheral arterial disease.

Science.gov (United States)

Zander, Nicole; Demirel, Ebru-Berrin; Augustin, Matthias; Sommer, Rachel; Debus, Eike Sebastian; Breuer, Peter; Blome, Christine

2018-01-25

The aim of this study was to develop and validate a specific Patient Benefit Index (PBI) version for the treatment of peripheral arterial disease (PAD). A non-interventional longitudinal development study was conducted. The first phase comprised a qualitative pre-study with n = 50 patients, in which the PBI was adapted for peripheral arterial disease. The resulting Patient Benefit Index for peripheral arterial disease (PBI-PAD) was validated in the second phase at two points of measurement. The total PBI-PAD score was calculated by weighting item-wise the achievement of treatment goals with the initially assessed needs. Feasibility, internal consistency, and construct validity were analysed and the generic three level version of the EuroQol five-dimensional questionnaire (EQ-5D-3L) and the disease-specific instrument Vascular Quality of Life Questionnaire (VascuQoL) were used for convergent validation. In the pre-study, the PBI-PAD, consisting of 12 items, was developed. N = 103 patients participated in the main study. At T2, data were available for n = 57 patients. Mean age was 71.0 years ± 9.1 and 66.7 % of the participants were male. The amount of missing values of the PBI-PAD score was low (PBI (needs at T1 and benefits at T2) were internally consistent with Cronbach's alpha > 0.7. PBI-PAD total score correlated significantly with the T2-T1-differences of the EuroQol-visual analogue scale (EQ VAS) (r = 0.4, p = 0.007) and the Vascular Quality of Life Questionnaire (r = 0.5, p PBI-PAD is a feasible, internally consistent, and valid instrument to assess patient-relevant benefits in PAD patients receiving minimally invasive treatment or surgical procedures. It can be recommended for use in routine care as well as in clinical studies.

Validation of forcefields in predicting the physical and thermophysical properties of emeraldine base polyaniline

NARCIS (Netherlands)

Chen, X.P.; Yuan, C.A.; Wong, C.K.Y.; Koh, S.W.; Zhang, G.Q.

2011-01-01

We report a molecular modelling study to validate the forcefields [condensed-phase optimised molecular potentials for atomistic simulation studies (COMPASS) and polymer-consistent forcefield (PCFF)] in predicting the physical and thermophysical properties of polymers. This work comprises of two key

Security-enhanced phase encryption assisted by nonlinear optical correlation via sparse phase

International Nuclear Information System (INIS)

Chen, Wen; Chen, Xudong; Wang, Xiaogang

2015-01-01

We propose a method for security-enhanced phase encryption assisted by a nonlinear optical correlation via a sparse phase. Optical configurations are established based on a phase retrieval algorithm for embedding an input image and the secret data into phase-only masks. We found that when one or a few phase-only masks generated during data hiding are sparse, it is possible to integrate these sparse masks into those phase-only masks generated during the encoding of the input image. Synthesized phase-only masks are used for the recovery, and sparse distributions (i.e., binary maps) for generating the incomplete phase-only masks are considered as additional parameters for the recovery of secret data. It is difficult for unauthorized receivers to know that a useful phase has been sparsely distributed in the finally generated phase-only masks for secret-data recovery. Only when the secret data are correctly verified can the input image obtained with valid keys be claimed as targeted information. (paper)

Phase change material thermal storage for biofuel preheating in micro trigeneration application: A numerical study

International Nuclear Information System (INIS)

Wu, Dawei; Chen, Junlong; Roskilly, Anthony P.

2015-01-01

Highlights: • Engine exhaust heat driven phase change material thermal storage. • Fuel preheating for direct use of straight plant oil on diesel engine. • CFD aided design of the phase change material thermal storage. • Melting and solidification model considering natural convection. - Abstract: A biofuel micro trigeneration prototype has been developed to utilise local energy crop oils as fuel in rural areas and developing countries. Straight plant oils (SPOs) only leave behind very little carbon footprint during its simply production process compared to commercial biodiesels in refineries, but the high viscosity of SPOs causes difficulties at engine cold starts, which further results in poor fuel atomisation, compromised engine performance and fast engine deterioration. In this study, a phase change material (PCM) thermal storage is designed to recover and store engine exhaust heat to preheat SPOs at cold starts. High temperature commercial paraffin is selected as the PCM to meet the optimal preheating temperature range of 70–90 °C, in terms of the SPO property study. A numerical model of the PCM thermal storage is developed and validated by references. The PCM melting and solidification processes with the consideration of natural convection in liquid zone are simulated in ANSYS-FLUENT to verify the feasibility of the PCM thermal storage as a part of the self-contained biofuel micro trigeneration prototype

Ultrasonic phased array examination of circumferential weld joint in reactor pressure vessel of BWR

Energy Technology Data Exchange (ETDEWEB)

Nanekar, Paritosh, E-mail: pnanekar@barc.gov.in [Quality Assurance Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Jothilakshmi, N. [Quality Assurance Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Jayakumar, T. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

2013-12-15

Highlights: • Phased array technique developed for weld joint inspection in BWR pressure vessel. • Simulation studies were carried out for conventional and phased array probe. • Conventional ultrasonic test shows in-adequate weld coverage and poor resolution. • Focused sound beam in phased array results in good resolution and sensitivity. • Ultrasonic phased array technique is validated on mock-up with reference defects. - Abstract: The weld joints in the reactor pressure vessel (RPV) of Boiling Water Reactors (BWR) are required to be examined periodically for assurance of structural integrity. Ultrasonic phased array examination technique has been developed in authors’ laboratory for inspection of the top flange to shell circumferential weld joint in RPV of BWRs, which are in operation in India since the late 1960s. The development involved detailed simulation studies for computation of focal laws followed by validation on mock-up. The paper brings out the limitations of the conventional ultrasonic technique and how this can be overcome by the phased array approach for the weld joint under consideration. The phased array technique was successfully employed for field examination of this weld joint in RPV during the re-fuelling outage.

Adaptive nonlinear control of single-phase to three-phase UPS system

Directory of Open Access Journals (Sweden)

Kissaoui M.

2014-01-01

Full Text Available This work deals with the problems of uninterruptible power supplies (UPS based on the single-phase to three-phase converters built in two stages: an input bridge rectifier and an output three phase inverter. The two blocks are joined by a continuous intermediate bus. The objective of control is threefold: i power factor correction “PFC”, ii generating a symmetrical three-phase system at the output even if the load is unknown, iii regulating the DC bus voltage. The synthesis of controllers has been reached by two nonlinear techniques that are the sliding mode and adaptive backstepping control. The performances of regulators have been validated by numerical simulation in MATLAB / SIMULINK.

Theoretical study of titanium phases; Etude theorique des phases du titane

Energy Technology Data Exchange (ETDEWEB)

Trinite, V

2006-10-15

The aim of this work is to obtain a good understanding of the phase diagram of titanium within density functional theory. This diagram is composed of the alpha phase, the high pressure omega phase and the high temperature beta phase. This requires the differences in total energy to be predicted with a great precision, because these differences are around 50 meV. I find the omega phase to be the most stable one by ab initio calculation at zero temperature and pressure, in contradiction to the experimental results. I find this inversion of the stability also appears in titanium dioxide and zirconium. I have analyzed all the approximations brought into play in the ab initio approach. I have estimated the zero point energy and studied the impact of including the semi-core states as well as the effect of the exchange-correlation functionals. The conclusion is that the usual approximations for the exchange-correlation generate the biggest part of the error. A possible correction is to take into account the electronic self-interaction. I have apply this correction to the semi-core states and find a systematic improvement of the cell parameters, but no improvement on the phase stability. So I can conclude that a better description of the exchange interaction on the localized 3d states is needed. Although the standard functionals of exchange-correlation are not accurate enough to predict the phase diagrams of titanium, they perform well in describing physical properties less demanding in terms of precision, like elastic constants. However, I find important that the predicted equilibrium volume must be precise, as these properties are found strongly dependent on the volume. (author)

Verification and validation of computer based systems for PFBR

International Nuclear Information System (INIS)

Thirugnanamurthy, D.

2017-01-01

Verification and Validation (V and V) process is essential to build quality into system. Verification is the process of evaluating a system to determine whether the products of each development phase satisfies the requirements imposed by the previous phase. Validation is the process of evaluating a system at the end of the development process to ensure compliance with the functional, performance and interface requirements. This presentation elaborates the V and V process followed, documents submission requirements in each stage, V and V activities, check list used for reviews in each stage and reports

Reasoning with Inductive Argument Test: A Study of Validity and Reliability

Directory of Open Access Journals (Sweden)

Mehmet Emrah Karadere

2013-12-01

Conclusion: The preliminary data obtained from the study of reliability and validity of the scale shows that ‘Reasoning with Inductive Argument Test’ supports reliability and validity in Turkish population. [JCBPR 2013; 2(3.000: 156-161

Study and development of an achromatic phase shifter for nulling interferometry

International Nuclear Information System (INIS)

Brachet, Frank

2005-01-01

The Darwin mission is a project of the European Space Agency that should allow around 2015 the search for extra-solar planets and a spectral analysis of their atmospheres to detect gases and particularly tracers of life. The basic concept of the instrument is a Bracewell nulling interferometer. It allows the high angular resolution and high dynamic range necessary to cancel the light coming from the star to keep the planetary one. The Darwin mission technological key-points require preliminary laboratory experiments to validate each element before any space application. Among these, the π achromatic phase shifter included in the interferometer to cancel the starlight has to be achromatic in the whole Darwin spectral band from 6 to 18 μm. There are many solutions to create this phase shift. This work presents the study and development of one of these techniques based on dispersive prisms and tested on the polychromatic test bench SYNAPSE. After an introduction of Darwin stakes, both from an exo-planetological and exobiological point of view, we introduce different achromatic phase shifter techniques. The concept based on prismatic dispersive plates is then detailed, along with the development of the SYNAPSE test bench working in near infrared. We finally show that this bench allowed to maintain rejection ratio better than 4 000 (corresponding to a 2,5.10 -4 stellar leaks level) in the whole K band (from 2 to 2,5 μm) during several minutes. These results also show that more than the absolute rejection ratio needed in the whole Darwin spectral band, their stability will be the real stake during observations. (author) [fr

Derivation and validation of two decision instruments for selective chest CT in blunt trauma: a multicenter prospective observational study (NEXUS Chest CT).

Science.gov (United States)

Rodriguez, Robert M; Langdorf, Mark I; Nishijima, Daniel; Baumann, Brigitte M; Hendey, Gregory W; Medak, Anthony J; Raja, Ali S; Allen, Isabel E; Mower, William R

2015-10-01

Unnecessary diagnostic imaging leads to higher costs, longer emergency department stays, and increased patient exposure to ionizing radiation. We sought to prospectively derive and validate two decision instruments (DIs) for selective chest computed tomography (CT) in adult blunt trauma patients. From September 2011 to May 2014, we prospectively enrolled blunt trauma patients over 14 y of age presenting to eight US, urban level 1 trauma centers in this observational study. During the derivation phase, physicians recorded the presence or absence of 14 clinical criteria before viewing chest imaging results. We determined injury outcomes by CT radiology readings and categorized injuries as major or minor according to an expert-panel-derived clinical classification scheme. We then employed recursive partitioning to derive two DIs: Chest CT-All maximized sensitivity for all injuries, and Chest CT-Major maximized sensitivity for only major thoracic injuries (while increasing specificity). In the validation phase, we employed similar methodology to prospectively test the performance of both DIs. We enrolled 11,477 patients-6,002 patients in the derivation phase and 5,475 patients in the validation phase. The derived Chest CT-All DI consisted of (1) abnormal chest X-ray, (2) rapid deceleration mechanism, (3) distracting injury, (4) chest wall tenderness, (5) sternal tenderness, (6) thoracic spine tenderness, and (7) scapular tenderness. The Chest CT-Major DI had the same criteria without rapid deceleration mechanism. In the validation phase, Chest CT-All had a sensitivity of 99.2% (95% CI 95.4%-100%), a specificity of 20.8% (95% CI 19.2%-22.4%), and a negative predictive value (NPV) of 99.8% (95% CI 98.9%-100%) for major injury, and a sensitivity of 95.4% (95% CI 93.6%-96.9%), a specificity of 25.5% (95% CI 23.5%-27.5%), and a NPV of 93.9% (95% CI 91.5%-95.8%) for either major or minor injury. Chest CT-Major had a sensitivity of 99.2% (95% CI 95.4%-100%), a specificity of

Validation of a fully automated solid‐phase extraction and ultra‐high‐performance liquid chromatography–tandem mass spectrometry method for quantification of 30 pharmaceuticals and metabolites in post‐mortem blood and brain samples

DEFF Research Database (Denmark)

Nielsen, Marie Katrine Klose; Nedahl, Michael; Johansen, Sys Stybe

2018-01-01

In this study, we present the validation of an analytical method capable of quantifying 30 commonly encountered pharmaceuticals and metabolites in whole blood and brain tissue from forensic cases. Solid‐phase extraction was performed by a fully automated robotic system, thereby minimising manual...... labour and human error while increasing sample throughput, robustness, and traceability. The method was validated in blood in terms of selectivity, linear range, matrix effect, extraction recovery, process efficiency, carry‐over, stability, precision, and accuracy. Deuterated analogues of each analyte....../kg. Thus, the linear range covered both therapeutic and toxic levels. The method showed acceptable accuracy and precision, with accuracies ranging from 80 to 118% and precision below 19% for the majority of the analytes. Linear range, matrix effect, extraction recovery, process efficiency, precision...

The Jackson Career Explorer: Two Further Validity Studies

Science.gov (United States)

Schermer, Julie Aitken

2012-01-01

The present report consists of two further validity studies using the Jackson Career Explorer (JCE), a short form and continuous version of the Jackson Vocational Interest Survey, measuring 34 interests. The first study examined the relationships between the JCE and five personality factors, from a sample of 528 individuals. The correlations found…

Studying Suspended Sediment Mechanism with Two-Phase PIV

Science.gov (United States)

Matinpour, H.; Atkinson, J. F.; Bennett, S. J.; Guala, M.

2017-12-01

Suspended sediment transport affects soil erosion, agriculture and water resources quality. Turbulent diffusion is the most primary force to maintain sediments in suspension. Although extensive previous literature have been studying the interactions between turbulent motion and suspended sediment, mechanism of sediments in suspension is still poorly understood. In this study, we investigate suspension of sediments as two distinct phases: one phase of sediments and another phase of fluid with turbulent motions. We designed and deployed a state-of-the-art two-phase PIV measurement technique to discriminate these two phases and acquire velocities of each phase separately and simultaneously. The technique that we have developed is employing a computer-vision based method, which enables us to discriminate sediment particles from fluid tracer particles based on two thresholds, dissimilar particle sizes and different particle intensities. Results indicate that fluid turbulence decreases in the presence of suspended sediments. Obtaining only sediment phase consecutive images enable us to compute fluctuation sediment concentration. This result enlightens understanding of complex interaction between the fluctuation velocities and the fluctuation of associated mass and compares turbulent viscosity with turbulent eddy diffusivity experimentally.

Turkish adaptation of the pregnancy-related anxiety questionnaire-revised 2: Validity and reliability study in multiparous and primiparous pregnancy.

Science.gov (United States)

Aksoy Derya, Yeşim; Timur Taşhan, Sermin; Duman, Mesude; Durgun Ozan, Yeter

2018-07-01

The purpose of this study was to create a Turkish version of the Pregnancy-Related Anxiety Questionnaire-Revised 2 (PRAQR2), which was revised for application to multiparous and primiparous pregnancy, and to explore its psychometric characteristics in multiparous and primiparous pregnancy. This study was methodologically designed to assess the reliability and validity of the PRAQ-R2. The study was carried out in the obstetrics clinic of a training and research hospital in Malatya. A total of 616 healthy pregnant women (399 multiparous and 217 primiparous) constituted the sample of the study. The cultural adaptation process of the questionnaire was conducted in three phases: language validity, content validity, and pilot application. Exploratory factor analysis (EFA) and confirmatory factor analysis (CFA) were used to test the construct validity of the questionnaire. The reliability of the PRAQ-R2 was evaluated with Cronbach's alpha internal consistency coefficient, item-total correlation, test-retest analysis, and parallel forms reliability. The EFA revealed that the PRAQ-R2 consists of 10 items for the multiparous group and 11 for the primiparous group after adding the item ``I am anxious about the delivery because I have never experienced one before.'' The CFA for both groups supported the three-factor questionnaire yielded by the EFA. Good fit index values were obtained in both groups. Cronbach's alpha internal consistency coefficient ranged from 0.81 to 0.93 for the multiparous group and 0.87 to 0.94 for the primiparous group for the complete PRAQ-R2 and each of its subdimensions. In addition, the item-total correlation, test-retest analysis, and parallel forms reliability of the questionnaire were highly correlated. The PRAQ-R2 is a valid and reliable instrument that can be used to evaluate the level of anxiety in Turkish pregnant women irrespective of parity. The use of the PRAQ-R2 in prenatal healthcare services will contribute to the early diagnosis

A Phase Current Reconstruction Approach for Three-Phase Permanent-Magnet Synchronous Motor Drive

Directory of Open Access Journals (Sweden)

Hao Yan

2016-10-01

Full Text Available Three-phase permanent-magnet synchronous motors (PMSMs are widely used in renewable energy applications such as wind power generation, tidal energy and electric vehicles owing to their merits such as high efficiency, high precision and high reliability. To reduce the cost and volume of the drive system, techniques of reconstructing three-phase current using a single current sensor have been reported for three-phase alternating current (AC control system using the power converts. In existing studies, the reconstruction precision is largely influenced by reconstructing dead zones on the Space Vector Pulse Width Modulation (SVPWM plane, which requires other algorithms to compensate either by modifying PWM modulation or by phase-shifting of the PWM signal. In this paper, a novel extended phase current reconstruction approach for PMSM drive is proposed. Six novel installation positions are obtained by analyzing the sampling results of the current paths between each two power switches. By arranging the single current sensor at these positions, the single current sensor is sampled during zero voltage vectors (ZVV without modifying the PWM signals. This proposed method can reconstruct the three-phase currents without any complex algorithms and is available in the sector boundary region and low modulation region. Finally, this method is validated by experiments.

Local preparation and evaluation of liquid phase radioimmunoassay for determination of human serum cortisol

International Nuclear Information System (INIS)

Sallam, Kh.M.; El-Bayoumy, A.S.A.; Ebeid, N.H.; Michael, E.; Zein, N.; Elfarargy, Ah.F.

2017-01-01

The main objective of the present study was the preparation of the primary reagents of cortisol radioimmunoassay (RIA) using liquid phase double antibody technique. Three basic components were prepared and characterized to obtain valid and accurate system. These components were polyclonal anti-cortisol antibody, "1"2"5I-cortisol RIA tracer and cortisol standards. Cortisol requires conjugation step to be real antigen. Therefore, in this study this mandatory conjugation step was performed & characterized. Then formulation, optimization and validation of this liquid phase RIA technique were carried out. This assay is precise, specific and sensitive enough for using as a diagnostic tool for the adrenal cortex status. (author)

A methodology for PSA model validation

International Nuclear Information System (INIS)

Unwin, S.D.

1995-09-01

This document reports Phase 2 of work undertaken by Science Applications International Corporation (SAIC) in support of the Atomic Energy Control Board's Probabilistic Safety Assessment (PSA) review. A methodology is presented for the systematic review and evaluation of a PSA model. These methods are intended to support consideration of the following question: To within the scope and depth of modeling resolution of a PSA study, is the resultant model a complete and accurate representation of the subject plant? This question was identified as a key PSA validation issue in SAIC's Phase 1 project. The validation methods are based on a model transformation process devised to enhance the transparency of the modeling assumptions. Through conversion to a 'success-oriented' framework, a closer correspondence to plant design and operational specifications is achieved. This can both enhance the scrutability of the model by plant personnel, and provide an alternative perspective on the model that may assist in the identification of deficiencies. The model transformation process is defined and applied to fault trees documented in the Darlington Probabilistic Safety Evaluation. A tentative real-time process is outlined for implementation and documentation of a PSA review based on the proposed methods. (author). 11 refs., 9 tabs., 30 refs

Extension of CFD Codes Application to Two-Phase Flow Safety Problems - Phase 3

International Nuclear Information System (INIS)

Bestion, D.; Anglart, H.; Mahaffy, J.; Lucas, D.; Song, C.H.; Scheuerer, M.; Zigh, G.; Andreani, M.; Kasahara, F.; Heitsch, M.; Komen, E.; Moretti, F.; Morii, T.; Muehlbauer, P.; Smith, B.L.; Watanabe, T.

2014-11-01

The Writing Group 3 on the extension of CFD to two-phase flow safety problems was formed following recommendations made at the 'Exploratory Meeting of Experts to Define an Action Plan on the Application of Computational Fluid Dynamics (CFD) Codes to Nuclear Reactor Safety Problems' held in Aix-en-Provence, in May 2002. Extension of CFD codes to two-phase flow is significant potentiality for the improvement of safety investigations, by giving some access to smaller scale flow processes which were not explicitly described by present tools. Using such tools as part of a safety demonstration may bring a better understanding of physical situations, more confidence in the results, and an estimation of safety margins. The increasing computer performance allows a more extensive use of 3D modelling of two-phase Thermal hydraulics with finer nodalization. However, models are not as mature as in single phase flow and a lot of work has still to be done on the physical modelling and numerical schemes in such two-phase CFD tools. The Writing Group listed and classified the NRS problems where extension of CFD to two-phase flow may bring real benefit, and classified different modelling approaches in a first report (Bestion et al., 2006). First ideas were reported about the specification and analysis of needs in terms of validation and verification. It was then suggested to focus further activity on a limited number of NRS issues with a high priority and a reasonable chance to be successful in a reasonable period of time. The WG3-step 2 was decided with the following objectives: - selection of a limited number of NRS issues having a high priority and for which two-phase CFD has a reasonable chance to be successful in a reasonable period of time; - identification of the remaining gaps in the existing approaches using two-phase CFD for each selected NRS issue; - review of the existing data base for validation of two-phase CFD application to the selected NRS problems

Development and validation of a casemix classification to predict costs of specialist palliative care provision across inpatient hospice, hospital and community settings in the UK: a study protocol.

Science.gov (United States)

Guo, Ping; Dzingina, Mendwas; Firth, Alice M; Davies, Joanna M; Douiri, Abdel; O'Brien, Suzanne M; Pinto, Cathryn; Pask, Sophie; Higginson, Irene J; Eagar, Kathy; Murtagh, Fliss E M

2018-03-17

Provision of palliative care is inequitable with wide variations across conditions and settings in the UK. Lack of a standard way to classify by case complexity is one of the principle obstacles to addressing this. We aim to develop and validate a casemix classification to support the prediction of costs of specialist palliative care provision. Phase I: A cohort study to determine the variables and potential classes to be included in a casemix classification. Data are collected from clinicians in palliative care services across inpatient hospice, hospital and community settings on: patient demographics, potential complexity/casemix criteria and patient-level resource use. Cost predictors are derived using multivariate regression and then incorporated into a classification using classification and regression trees. Internal validation will be conducted by bootstrapping to quantify any optimism in the predictive performance (calibration and discrimination) of the developed classification. Phase II: A mixed-methods cohort study across settings for external validation of the classification developed in phase I. Patient and family caregiver data will be collected longitudinally on demographics, potential complexity/casemix criteria and patient-level resource use. This will be triangulated with data collected from clinicians on potential complexity/casemix criteria and patient-level resource use, and with qualitative interviews with patients and caregivers about care provision across difference settings. The classification will be refined on the basis of its performance in the validation data set. The study has been approved by the National Health Service Health Research Authority Research Ethics Committee. The results are expected to be disseminated in 2018 through papers for publication in major palliative care journals; policy briefs for clinicians, commissioning leads and policy makers; and lay summaries for patients and public. ISRCTN90752212. © Article author

Development of a quality-assessment tool for experimental bruxism studies: reliability and validity.

Science.gov (United States)

Dawson, Andreas; Raphael, Karen G; Glaros, Alan; Axelsson, Susanna; Arima, Taro; Ernberg, Malin; Farella, Mauro; Lobbezoo, Frank; Manfredini, Daniele; Michelotti, Ambra; Svensson, Peter; List, Thomas

2013-01-01

To combine empirical evidence and expert opinion in a formal consensus method in order to develop a quality-assessment tool for experimental bruxism studies in systematic reviews. Tool development comprised five steps: (1) preliminary decisions, (2) item generation, (3) face-validity assessment, (4) reliability and discriminitive validity assessment, and (5) instrument refinement. The kappa value and phi-coefficient were calculated to assess inter-observer reliability and discriminative ability, respectively. Following preliminary decisions and a literature review, a list of 52 items to be considered for inclusion in the tool was compiled. Eleven experts were invited to join a Delphi panel and 10 accepted. Four Delphi rounds reduced the preliminary tool-Quality-Assessment Tool for Experimental Bruxism Studies (Qu-ATEBS)- to 8 items: study aim, study sample, control condition or group, study design, experimental bruxism task, statistics, interpretation of results, and conflict of interest statement. Consensus among the Delphi panelists yielded good face validity. Inter-observer reliability was acceptable (k = 0.77). Discriminative validity was excellent (phi coefficient 1.0; P reviews of experimental bruxism studies, exhibits face validity, excellent discriminative validity, and acceptable inter-observer reliability. Development of quality assessment tools for many other topics in the orofacial pain literature is needed and may follow the described procedure.

Experimental and Computational Study of Two-phase (Air–Palm Oil Flow through Pipe and Control Valve in Series

Directory of Open Access Journals (Sweden)

Arivazhagan M.

2009-03-01

Full Text Available The contact of two or more immiscible liquids is encountered widely in the chemical and petroleum industries. Studies on operating characteristics of control valves with two phase flow have not been given much attention in the literature despite its industrial importance during design and selection as well as plant operations .The present work attempts to study experimentally the effect of two phase flow on pressure drop across pipe and control valve in series and compare with simulated results. Two-phase computational fluid dynamics (CFD calculations, using commercial CFD package FLUENT 6.2.16, were employed to calculate the simulated the pressure drop in Air–Palm oil flow in pipes and control valves. The Air flow rate varied from 25 to100 l/h flow rate. For constant valve position and Air flow rate, the Palm oil flow rate was varied from 50 to 150 l/h. The numerical results were validated against experimental data. The prediction of the pressure drop characteristics in pipe and valve were within an average error of about ± 3 %. A comparison of experimental and computed profiles was found to be in good agreement.

Analytical Method Validation of High-Performance Liquid Chromatography and Stability-Indicating Study of Medroxyprogesterone Acetate Intravaginal Sponges

Directory of Open Access Journals (Sweden)

Nidal Batrawi

2017-02-01

Full Text Available Medroxyprogesterone acetate is widely used in veterinary medicine as intravaginal dosage for the synchronization of breeding cycle in ewes and goats. The main goal of this study was to develop reverse-phase high-performance liquid chromatography method for the quantification of medroxyprogesterone acetate in veterinary vaginal sponges. A single high-performance liquid chromatography/UV isocratic run was used for the analytical assay of the active ingredient medroxyprogesterone. The chromatographic system consisted of a reverse-phase C18 column as the stationary phase and a mixture of 60% acetonitrile and 40% potassium dihydrogen phosphate buffer as the mobile phase; the pH was adjusted to 5.6. The method was validated according to the International Council for Harmonisation (ICH guidelines. Forced degradation studies were also performed to evaluate the stability-indicating properties and specificity of the method. Medroxyprogesterone was eluted at 5.9 minutes. The linearity of the method was confirmed in the range of 0.0576 to 0.1134 mg/mL ( R 2 > 0.999. The limit of quantification was shown to be 3.9 µg/mL. Precision and accuracy ranges were found to be %RSD <0.2 and 98% to 102%, respectively. Medroxyprogesterone capacity factor value of 2.1, tailing factor value of 1.03, and resolution value of 3.9 were obtained in accordance with ICH guidelines. Based on the obtained results, a rapid, precise, accurate, sensitive, and cost-effective analysis procedure was proposed for quantitative determination of medroxyprogesterone in vaginal sponges. This analytical method is the only available method to analyse medroxyprogesterone in veterinary intravaginal dosage form.

Phase field model for the study of boiling

International Nuclear Information System (INIS)

Ruyer, P.

2006-07-01

This study concerns both the modeling and the numerical simulation of boiling flows. First we propose a review concerning nucleate boiling at high wall heat flux and focus more particularly on the current understanding of the boiling crisis. From this analysis we deduce a motivation for the numerical simulation of bubble growth dynamics. The main and remaining part of this study is then devoted to the development and analyze of a phase field model for the liquid-vapor flows with phase change. We propose a thermodynamic quasi-compressible formulation whose properties match the one required for the numerical study envisaged. The system of governing equations is a thermodynamically consistent regularization of the sharp interface model, that is the advantage of the di use interface models. We show that the thickness of the interface transition layer can be defined independently from the thermodynamic description of the bulk phases, a property that is numerically attractive. We derive the kinetic relation that allows to analyze the consequences of the phase field formulation on the model of the dissipative mechanisms. Finally we study the numerical resolution of the model with the help of simulations of phase transition in simple configurations as well as of isothermal bubble dynamics. (author)

Toddler physical activity study: laboratory and community studies to evaluate accelerometer validity and correlates

Directory of Open Access Journals (Sweden)

Erin R. Hager

2016-09-01

Full Text Available Abstract Background Toddlerhood is an important age for physical activity (PA promotion to prevent obesity and support a physically active lifestyle throughout childhood. Accurate assessment of PA is needed to determine trends/correlates of PA, time spent in sedentary, light, or moderate-vigorous PA (MVPA, and the effectiveness of PA promotion programs. Due to the limited availability of objective measures that have been validated and evaluated for feasibility in community studies, it is unclear which subgroups of toddlers are at the highest risk for inactivity. Using Actical ankle accelerometry, the objectives of this study are to develop valid thresholds, examine feasibility, and examine demographic/ anthropometric PA correlates of MVPA among toddlers from low-income families. Methods Two studies were conducted with toddlers (12–36 months. Laboratory Study (n = 24- Two Actical accelerometers were placed on the ankle. PA was observed using the Child Activity Rating Scale (CARS, prescribed activities. Analyses included device equivalence reliability (correlation: activity counts of two Acticals, criterion-related validity (correlation: activity counts and CARS ratings, and sensitivity/specificity for thresholds. Community Study (n = 277, low-income mother-toddler dyads recruited- An Actical was worn on the ankle for > 7 days (goal >5, 24-h days. Height/weight was measured. Mothers reported demographics. Analyses included frequencies (feasibility and stepwise multiple linear regression (sMLR. Results Laboratory Study- Acticals demonstrated reliability (r = 0.980 and validity (r = 0.75. Thresholds demonstrated sensitivity (86 % and specificity (88 %. Community Study- 86 % wore accelerometer, 69 % had valid data (mean = 5.2 days. Primary reasons for missing/invalid data: refusal (14 % and wear-time ≤2 days (11 %. The MVPA threshold (>2200 cpm yielded 54 min/day. In sMLR, MVPA was associated with age (older�

The global status of freshwater fish age validation studies and a prioritization framework for future research

Science.gov (United States)

Pope, Kevin L.; Hamel, Martin J.; Pegg, Mark A.; Spurgeon, Jonathan J.

2016-01-01

Age information derived from calcified structures is commonly used to estimate recruitment, growth, and mortality for fish populations. Validation of daily or annual marks on age structures is often assumed, presumably due to a lack of general knowledge concerning the status of age validation studies. Therefore, the current status of freshwater fish age validation studies was summarized to show where additional effort is needed, and increase the accessibility of validation studies to researchers. In total, 1351 original peer-reviewed articles were reviewed from freshwater systems that studied age in fish. Periodicity and age validation studies were found for 88 freshwater species comprising 21 fish families. The number of age validation studies has increased over the last 30 years following previous calls for more research; however, few species have validated structures spanning all life stages. In addition, few fishes of conservation concern have validated ageing structures. A prioritization framework, using a combination of eight characteristics, is offered to direct future age validation studies and close the validation information gap. Additional study, using the offered prioritization framework, and increased availability of published studies that incorporate uncertainty when presenting research results dealing with age information are needed.

Client Motivation for Therapy Scale Adaptation to Turkish: Reliability and Validity Study

Directory of Open Access Journals (Sweden)

Omer Ozer

2017-03-01

Full Text Available The purpose of this study is to adapt Client Motivation for Therapy Scale to the Turkish. Study group of the research consisted of 109 undergraduate students studying in Anadolu and Gaziosmanpasa Universities, in academic year 2014-2015. After establishing language, the validity and reliability of the scale of analysis was examined. Item-factor structure has been tested for compliance with a model by confirmatory factor analysis (CFA. Based on this, five-factor structure of Motivation for Counseling/Therapy Scale has been validated. The coefficient of the total internal consistency is found .79. As a result of the analysis for adaptation of Client Motivation for Therapy Scale to Turkish, it can be said that the scale is a reliable and valid measurement tool. It is suggested that studies on reliability and validity of Client Motivation for Therapy Scale on other samples can be made in future researches. [Psikiyatride Guncel Yaklasimlar - Current Approaches in Psychiatry 2017; 9(1.000: 13-30

German risk study, phase (DRS-B)

International Nuclear Information System (INIS)

Werner, W.

1992-01-01

The first risk investigations were primarily intended to estimate the risk of accidents in nuclear power plants and to compare it with other natural risk and civilization risks. The American reactor safety study WASH 1400 and the German risk study phase A (DRS-A) gave a detailed analyses of the offsite consequences of accidents, especially the magnitude and frequency of health damage for the population. Risk investigations today are primarily used to examine the design of safety systems and to further develop the entire safety concept. Safety investigations have shown that nuclear power plants still possess safety reserves if safety systems do not operate as planned. These safety reserves can be exploited in the sense of a further development of safety by plant internal emergency measures. One purpose of risk analyses is to identify such measures and to evaluate their feasibility and effectiveness. The most important goals of the investigations in DRS-B were: Identification of vulnerabilities and possible safety improvements; determination of safety reserves during accident sequences exceeding the design limits; evaluation of plant internal emergency measures. Thus, goals in phase B compared with phase A have changed from investigations of the magnitude of damage to detailed analysis of the plant systems response under accident conditions. The magnitude of possible fission product releases is also determined in phase B. However, no new accident consequence calculations are performed. Figs and tabs

An exploratory sequential design to validate measures of moral emotions.

Science.gov (United States)

Márquez, Margarita G; Delgado, Ana R

2017-05-01

This paper presents an exploratory and sequential mixed methods approach in validating measures of knowledge of the moral emotions of contempt, anger and disgust. The sample comprised 60 participants in the qualitative phase when a measurement instrument was designed. Item stems, response options and correction keys were planned following the results obtained in a descriptive phenomenological analysis of the interviews. In the quantitative phase, the scale was used with a sample of 102 Spanish participants, and the results were analysed with the Rasch model. In the qualitative phase, salient themes included reasons, objects and action tendencies. In the quantitative phase, good psychometric properties were obtained. The model fit was adequate. However, some changes had to be made to the scale in order to improve the proportion of variance explained. Substantive and methodological im-plications of this mixed-methods study are discussed. Had the study used a single re-search method in isolation, aspects of the global understanding of contempt, anger and disgust would have been lost.

Circulating tumor cells: clinical validity and utility.

Science.gov (United States)

Cabel, Luc; Proudhon, Charlotte; Gortais, Hugo; Loirat, Delphine; Coussy, Florence; Pierga, Jean-Yves; Bidard, François-Clément

2017-06-01

Circulating tumor cells (CTCs) are rare tumor cells and have been investigated as diagnostic, prognostic and predictive biomarkers in many types of cancer. Although CTCs are not currently used in clinical practice, CTC studies have accumulated a high level of clinical validity, especially in breast, lung, prostate and colorectal cancers. In this review, we present an overview of the current clinical validity of CTCs in metastatic and non-metastatic disease, and the main concepts and studies investigating the clinical utility of CTCs. In particular, this review will focus on breast, lung, colorectal and prostate cancer. Three major topics concerning the clinical utility of CTC are discussed-(1) treatment based on CTCs used as liquid biopsy, (2) treatment based on CTC count or CTC variations, and (3) treatment based on CTC biomarker expression. A summary of published or ongoing phase II and III trials is also presented.

Validation of an in vitro digestive system for studying macronutrient decomposition in humans.

Science.gov (United States)

Kopf-Bolanz, Katrin A; Schwander, Flurina; Gijs, Martin; Vergères, Guy; Portmann, Reto; Egger, Lotti

2012-02-01

The digestive process transforms nutrients and bioactive compounds contained in food to physiologically active compounds. In vitro digestion systems have proven to be powerful tools for understanding and monitoring the complex transformation processes that take place during digestion. Moreover, the investigation of the physiological effects of certain nutrients demands an in vitro digestive process that is close to human physiology. In this study, human digestion was simulated with a 3-step in vitro process that was validated in depth by choosing pasteurized milk as an example of a complex food matrix. The evolution and decomposition of the macronutrients was followed over the entire digestive process to the level of intestinal enterocyte action, using protein and peptide analysis by SDS-PAGE, reversed-phase HPLC, size exclusion HPLC, and liquid chromatography-MS. The mean peptide size after in vitro digestion of pasteurized milk was 5-6 amino acids (AA). Interestingly, mostly essential AA (93.6%) were released during in vitro milk digestion, a significantly different relative distribution compared to the total essential AA concentration of bovine milk (44.5%). All TG were degraded to FFA and monoacylglycerols. Herein, we present a human in vitro digestion model validated for its ability to degrade the macronutrients of dairy products comparable to physiological ranges. It is suited to be used in combination with a human intestinal cell culture system, allowing ex vivo bioavailability measurements and assessment of the bioactive properties of food components.

Development and validation of a dissolution test with reversed-phase high performance liquid chromatographic analysis for Candesartan cilexetil in tablet dosage forms

Directory of Open Access Journals (Sweden)

Vairappan Kamalakkannan

2016-09-01

Full Text Available A simple, rapid, selective and reproducible reversed-phase high performance liquid chromatographic (RP-HPLC method has been developed and validated for the estimation of release of Candesartan cilexetil (CC in tablets. Analysis was performed on an Agilent, Zorbax C8 column (150mm × 4.6mm, 5μm with the mobile phase consisting of phosphate buffer (pH2.5–acetonitrile (15:85, v/v at a flow rate of 1.0mL/min. UV detection was performed at 215nm and the retention time for CC was 2.2. The calibration curve was linear (correlation coefficient = 1.000 in the selected range of analyte. The optimized dissolution conditions include the USP apparatus 2 at a paddle rotation rate of 50rpm and 900mL of phosphate buffer (pH7.2 with 0.03% of polysorbate 80 as dissolution medium, at 37.0 ± 0.5°C. The method was validated for precision, linearity, specificity, accuracy, limit of quantitation and ruggedness. The system suitability parameters, such as theoretical plate, tailing factor and relative standard deviation (RSD between six standard replicates were well within the limits. The stability result shows that the drug is stable in the prescribed dissolution medium. Three different batches (A, B and C of the formulation containing 8mg of Candesartan cilexetil was performed with the developed method and the results showed no significant differences among the batches.

Development and validation study of the Smartphone Overuse Screening Questionnaire.

Science.gov (United States)

Lee, Han-Kyeong; Kim, Ji-Hae; Fava, Maurizio; Mischoulon, David; Park, Jae-Hyun; Shim, Eun-Jung; Lee, Eun-Ho; Lee, Ji Hyeon; Jeon, Hong Jin

2017-11-01

The aim of this study was to develop a screening questionnaire that could distinguish individuals at high risk of smartphone overuse from casual users. The reliability, validity, and diagnostic ability of the Smartphone Overuse Screening Questionnaire (SOS-Q) were evaluated. Preliminary items were assessed by 50 addiction experts on-line, and 28 questions were selected. A total of 158 subjects recruited from six community centers for internet addiction participated in this study. The SOS-Q, Young's internet addiction scale, Korean scale for internet addiction, and Smartphone Scale for Smartphone Addiction (S-Scale) were used to assess the concurrent validity. Construct validity was supported by a six-factor model using an exploratory factor analysis. The internal consistency and the item-total correlations were favorable (α = 0.95, r = 0.35-0.81). The test-retest reliability was moderate (r = 0.70). The SOS-Q showed superior concurrent validity with the highest correlation between the S-Scale (r = 0.76). Receiver operating characteristic curve analysis revealed an area under the curve of 0.877. A cut-off point of 49 effectively categorized addiction high-risk group with a sensitivity of 0.81 and specificity of 0.86. Overall, the current study supports the use of SOS-Q as both a primary and supplementary measurement tool in a variety of settings. Copyright © 2017 Elsevier B.V. All rights reserved.

A numerical study on the heat and mass transfer of a micro heat pipe with a phase-change interface analysis

Science.gov (United States)

Jung, Eui Guk; Boo, Joon Hong

2017-11-01

A numerical study was conducted to analyze the heat and mass transfer in a micro heat pipe, with the thin-film theory applied to the phase change at the liquid-vapor interface. The model described the liquid and vapor distributions, phase change rate, wall temperature, pressure drop, and heat transfer rate in a micro heat pipe under normal operation. The reference cross-sectional geometry of the micro heat pipe was triangular, but the model could be applied to various geometries by utilizing a hydraulic diameter. In previous studies, to predict the thermal performance of a micro heat pipe, the phase change interface has usually been modeled using the Young-Laplace capillary equation, and the phase-change ratio has been estimated using terms such as vapor pressure, liquid pressure, and capillary pressure. In this study, a thermal numerical model for a micro heat pipe was developed using an augmented Young-Laplace equation. Consequently, terms that have been commonly excluded in previous studies, including the disjoining pressure, were included. The validity of the model was verified using the experimental results for the wall temperature of the micro heat pipe, wherein the relative error bound was less than 1 °C and 6 °C for the operating and condenser temperatures, respectively. The influence of the disjoining pressure on the heat transfer was analyzed and discussed for various operating temperatures and tilt angles.

Constructing a unique two-phase compressibility factor model for lean gas condensates

Energy Technology Data Exchange (ETDEWEB)

Moayyedi, Mahmood; Gharesheikhlou, Aliashghar [Research Institute of Petroleum Industry (RIPI), Tehran (Iran, Islamic Republic of); Azamifard, Arash; Mosaferi, Emadoddin [Amirkabir University of Technology (AUT), Tehran (Iran, Islamic Republic of)

2015-02-15

Generating a reliable experimental model for two-phase compressibility factor in lean gas condensate reservoirs has always been demanding, but it was neglected due to lack of required experimental data. This study presents the main results of constructing the first two-phase compressibility factor model that is completely valid for Iranian lean gas condensate reservoirs. Based on a wide range of experimental data bank for Iranian lean gas condensate reservoirs, a unique two-phase compressibility factor model was generated using design of experiments (DOE) method and neural network technique (ANN). Using DOE, a swift cubic response surface model was generated for two-phase compressibility factor as a function of some selected fluid parameters for lean gas condensate fluids. The proposed DOE and ANN models were finally validated using four new independent data series. The results showed that there is a good agreement between experimental data and the proposed models. In the end, a detailed comparison was made between the results of proposed models.

Constructing a unique two-phase compressibility factor model for lean gas condensates

International Nuclear Information System (INIS)

Moayyedi, Mahmood; Gharesheikhlou, Aliashghar; Azamifard, Arash; Mosaferi, Emadoddin

2015-01-01

Generating a reliable experimental model for two-phase compressibility factor in lean gas condensate reservoirs has always been demanding, but it was neglected due to lack of required experimental data. This study presents the main results of constructing the first two-phase compressibility factor model that is completely valid for Iranian lean gas condensate reservoirs. Based on a wide range of experimental data bank for Iranian lean gas condensate reservoirs, a unique two-phase compressibility factor model was generated using design of experiments (DOE) method and neural network technique (ANN). Using DOE, a swift cubic response surface model was generated for two-phase compressibility factor as a function of some selected fluid parameters for lean gas condensate fluids. The proposed DOE and ANN models were finally validated using four new independent data series. The results showed that there is a good agreement between experimental data and the proposed models. In the end, a detailed comparison was made between the results of proposed models

Oak Ridge Health Studies phase 1 report, Volume 1: Oak Ridge Phase 1 overview

International Nuclear Information System (INIS)

Yarbrough, M.I.; Van Cleave, M.L.; Turri, P.; Daniel, J.

1993-09-01

In July 1991, the State of Tennessee initiated the Health Studies Agreement with the United States Department of Energy to carry out independent studies of possible adverse health effects in people living in the vicinity of the Oak Ridge Reservation. The health studies focus on those effects that could have resulted or could result from exposures to chemicals and radioactivity released at the Reservation since 1942. The major focus of the first phase was to complete a Dose Reconstruction Feasibility Study. This study was designed to find out if enough data exist about chemical and radionuclide releases from the Oak Ridge Reservation to conduct a second phase. The second phase will lead to estimates of the actual amounts or the ''doses'' of various contaminants received by people as a result of off-site releases. Once the doses of various contaminants have been estimated, scientists and physicians will be better able to evaluate whether adverse health effects could have resulted from the releases

Oak Ridge Health Studies phase 1 report, Volume 1: Oak Ridge Phase 1 overview

Energy Technology Data Exchange (ETDEWEB)

Yarbrough, M.I.; Van Cleave, M.L.; Turri, P.; Daniel, J.

1993-09-01

In July 1991, the State of Tennessee initiated the Health Studies Agreement with the United States Department of Energy to carry out independent studies of possible adverse health effects in people living in the vicinity of the Oak Ridge Reservation. The health studies focus on those effects that could have resulted or could result from exposures to chemicals and radioactivity released at the Reservation since 1942. The major focus of the first phase was to complete a Dose Reconstruction Feasibility Study. This study was designed to find out if enough data exist about chemical and radionuclide releases from the Oak Ridge Reservation to conduct a second phase. The second phase will lead to estimates of the actual amounts or the ``doses`` of various contaminants received by people as a result of off-site releases. Once the doses of various contaminants have been estimated, scientists and physicians will be better able to evaluate whether adverse health effects could have resulted from the releases.

German risk study on nuclear power stations. Phase B

International Nuclear Information System (INIS)

1989-11-01

The German Risk Study on Nuclear Power Stations is concerned with investigations of accidents in nuclear facilities and their associated risks. These investigations are undertaken on behalf of the federal Minister of Research and Technology. They have been broken down into two phases (Phase A and Phase B). The results of Phase A were published in 1979 (GRS 79). This report contains a summary of the investigations relating to Phase B. After an introduction setting out the basic principles and aim of the study, a general review will be given of the most important results. The course of the investigations and the results have already been published in a Technical Report (GRS 89). (author)

The present status of the study on the validity of concurrent verbalization

International Nuclear Information System (INIS)

Watanabe, Megumi; Takahashi, Hideaki.

1993-09-01

We reviewed study on the validity of the method of verbal reports. The method of verbal reports gives us detailed information about human cognitive process as compared with observing a sequence of actions, while it is subjected to criticism for the validity as data. Ericsson and Simon proposed a model of verbalization and investigated conditions to keep verbal reports valid. Although a lot of studies quote their model as a base of adopting the method of verbal reports, verification the validity of verbal reports is incomplete because effects of verbalization is not clear. We pointed out that it is necessary to take into consideration kinds of task strategies, effects of trial repetition, effects of task difficulty to examine precisely effects of verbalization. (author)

Software for imaging phase-shift interference microscope

Science.gov (United States)

Malinovski, I.; França, R. S.; Couceiro, I. B.

2018-03-01

In recent years absolute interference microscope was created at National Metrology Institute of Brazil (INMETRO). The instrument by principle of operation is imaging phase-shifting interferometer (PSI) equipped with two stabilized lasers of different colour as traceable reference wavelength sources. We report here some progress in development of the software for this instrument. The status of undergoing internal validation and verification of the software is also reported. In contrast with standard PSI method, different methodology of phase evaluation is applied. Therefore, instrument specific procedures for software validation and verification are adapted and discussed.

Measuring striving for understanding and learning value of geometry: a validity study

Science.gov (United States)

Ubuz, Behiye; Aydınyer, Yurdagül

2017-11-01

The current study aimed to construct a questionnaire that measures students' personality traits related to striving for understanding and learning value of geometry and then examine its psychometric properties. Through the use of multiple methods on two independent samples of 402 and 521 middle school students, two studies were performed to address this issue to provide support for its validity. In Study 1, exploratory factor analysis indicated the two-factor model. In Study 2, confirmatory factor analysis indicated the better fit of two-factor model compared to one or three-factor model. Convergent and discriminant validity evidence provided insight into the distinctiveness of the two factors. Subgroup validity evidence revealed gender differences for striving for understanding geometry trait favouring girls and grade level differences for learning value of geometry trait favouring the sixth- and seventh-grade students. Predictive validity evidence demonstrated that the striving for understanding geometry trait but not learning value of geometry trait was significantly correlated with prior mathematics achievement. In both studies, each factor and the entire questionnaire showed satisfactory reliability. In conclusion, the questionnaire was psychometrically sound.

How valid are claims for synergy in published clinical studies?

Science.gov (United States)

Ocana, A; Amir, E; Yeung, C; Seruga, B; Tannock, I F

2012-08-01

Clinical trials evaluating drug combinations are often stimulated by claims of synergistic interactions in preclinical models. Overuse or misuse of the term synergy could lead to poorly designed clinical studies. We searched PubMed using the terms 'synergy' or 'synergistic' and 'cancer' to select articles published between 2006 and 2010. Eligible studies were those that referred to synergy in preclinical studies to justify a drug combination evaluated in a clinical trial. Eighty-six clinical articles met eligibility criteria and 132 preclinical articles were cited in them. Most of the clinical studies were phase I (43%) or phase II trials (56%). Appropriate methods to evaluate synergy in preclinical studies included isobologram analysis in 18 studies (13.6%) and median effect in 10 studies (7.6%). Only 26 studies using animal models (39%) attempted to evaluate therapeutic index. There was no association between the result of the clinical trial and the use of an appropriate method to evaluate synergy (P=0.25, chi-squared test). Synergy is cited frequently in phase I and phase II studies to justify the evaluation of a specific drug combination. Inappropriate methods for evaluation of synergy and poor assessment of therapeutic index have been used in most preclinical articles.

Turkish Adaptation of the Mentorship Effectiveness Scale: A Validity and Reliability Study

Science.gov (United States)

Yirci, Ramazan; Karakose, Turgut; Uygun, Harun; Ozdemir, Tuncay Yavuz

2016-01-01

The purpose of this study is to adapt the Mentoring Relationship Effectiveness Scale to Turkish, and to conduct validity and reliability tests regarding the scale. The study group consisted of 156 university science students receiving graduate education. Construct validity and factor structure of the scale was analyzed first through exploratory…

Description and Validation of a MATLAB

DEFF Research Database (Denmark)

Johra, Hicham; Heiselberg, Per

This report aims to present the details and the validation tests of a single family house building energy model. The building model includes furniture / additional indoor content, phase change materials, ground source heat pump and water-based under floor heating system....

Multiattribute health utility scoring for the computerized adaptive measure CAT-5D-QOL was developed and validated.

Science.gov (United States)

Kopec, Jacek A; Sayre, Eric C; Rogers, Pamela; Davis, Aileen M; Badley, Elizabeth M; Anis, Aslam H; Abrahamowicz, Michal; Russell, Lara; Rahman, Md Mushfiqur; Esdaile, John M

2015-10-01

The CAT-5D-QOL is a previously reported item response theory (IRT)-based computerized adaptive tool to measure five domains (attributes) of health-related quality of life. The objective of this study was to develop and validate a multiattribute health utility (MAHU) scoring method for this instrument. The MAHU scoring system was developed in two stages. In phase I, we obtained standard gamble (SG) utilities for 75 hypothetical health states in which only one domain varied (15 states per domain). In phase II, we obtained SG utilities for 256 multiattribute states. We fit a multiplicative regression model to predict SG utilities from the five IRT domain scores. The prediction model was constrained using data from phase I. We validated MAHU scores by comparing them with the Health Utilities Index Mark 3 (HUI3) and directly measured utilities and by assessing between-group discrimination. MAHU scores have a theoretical range from -0.842 to 1. In the validation study, the scores were, on average, higher than HUI3 utilities and lower than directly measured SG utilities. MAHU scores correlated strongly with the HUI3 (Spearman ρ = 0.78) and discriminated well between groups expected to differ in health status. Results reported here provide initial evidence supporting the validity of the MAHU scoring system for the CAT-5D-QOL. Copyright © 2015 Elsevier Inc. All rights reserved.

Validation of the Australian Midwifery Standards Assessment Tool (AMSAT): A tool to assess midwifery competence.

Science.gov (United States)

Sweet, Linda; Bazargan, Maryam; McKellar, Lois; Gray, Joanne; Henderson, Amanda

2018-02-01

There is no current validated clinical assessment tool to measure the attainment of midwifery student competence in the midwifery practice setting. The lack of a valid assessment tool has led to a proliferation of tools and inconsistency in assessment of, and feedback on student learning. This research aimed to develop and validate a tool to assess competence of midwifery students in practice-based settings. A mixed-methods approach was used and the study implemented in two phases. Phase one involved the development of the AMSAT tool with qualitative feedback from midwifery academics, midwife assessors of students, and midwifery students. In phase two the newly developed AMSAT tool was piloted across a range of midwifery practice settings and ANOVA was used to compare scores across year levels, with feedback being obtained from assessors. Analysis of 150 AMSAT forms indicate the AMSAT as: reliable (Cronbach alpha greater than 0.9); valid-data extraction loaded predominantly onto one factor; and sensitivity scores indicating level of proficiency increased across the three years. Feedback evaluation forms (n=83) suggest acceptance of this tool for the purpose of both assessing and providing feedback on midwifery student's practice performance and competence. The AMSAT is a valid, reliable and acceptable midwifery assessment tool enables consistent assessment of midwifery student competence. This assists benchmarking across midwifery education programs. Copyright © 2017 Australian College of Midwives. Published by Elsevier Ltd. All rights reserved.

Preliminary Phase Field Computational Model Development

Energy Technology Data Exchange (ETDEWEB)

Li, Yulan [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hu, Shenyang Y. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Xu, Ke [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Suter, Jonathan D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); McCloy, John S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Johnson, Bradley R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ramuhalli, Pradeep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-12-15

experiments, special experimental methods were devised to create similar boundary conditions in the iron films. Preliminary MFM studies conducted on single and polycrystalline iron films with small sub-areas created with focused ion beam have correlated quite well qualitatively with phase-field simulations. However, phase-field model dimensions are still small relative to experiments thus far. We are in the process of increasing the size of the models and decreasing specimen size so both have identical dimensions. Ongoing research is focused on validation of the phase-field model. Validation is being accomplished through comparison with experimentally obtained MFM images (in progress), and planned measurements of major hysteresis loops and first order reversal curves. Extrapolation of simulation sizes to represent a more stochastic bulk-like system will require sampling of various simulations (i.e., with single non-magnetic defect, single magnetic defect, single grain boundary, single dislocation, etc.) with distributions of input parameters. These outputs can then be compared to laboratory magnetic measurements and ultimately to simulate magnetic Barkhausen noise signals.

Obtaining valid laboratory data in clinical trials conducted in resource diverse settings: lessons learned from a microbicide phase III clinical trial.

Directory of Open Access Journals (Sweden)

Tania Crucitti

2010-10-01

Full Text Available Over the last decade several phase III microbicides trials have been conducted in developing countries. However, laboratories in resource constrained settings do not always have the experience, infrastructure, and the capacity to deliver laboratory data meeting the high standards of clinical trials. This paper describes the design and outcomes of a laboratory quality assurance program which was implemented during a phase III clinical trial evaluating the efficacy of the candidate microbicide Cellulose Sulfate 6% (CS [1].In order to assess the effectiveness of CS for HIV and STI prevention, a phase III clinical trial was conducted in 5 sites: 3 in Africa and 2 in India. The trial sponsor identified an International Central Reference Laboratory (ICRL, responsible for the design and management of a quality assurance program, which would guarantee the reliability of laboratory data. The ICRL provided advice on the tests, assessed local laboratories, organized trainings, conducted supervision visits, performed re-tests, and prepared control panels. Local laboratories were provided with control panels for HIV rapid tests and Chlamydia trachomatis/Neisseria gonorrhoeae (CT/NG amplification technique. Aliquots from respective control panels were tested by local laboratories and were compared with results obtained at the ICRL.Overall, good results were observed. However, discordances between the ICRL and site laboratories were identified for HIV and CT/NG results. One particular site experienced difficulties with HIV rapid testing shortly after study initiation. At all sites, DNA contamination was identified as a cause of invalid CT/NG results. Both problems were timely detected and solved. Through immediate feedback, guidance and repeated training of laboratory staff, additional inaccuracies were prevented.Quality control guidelines when applied in field laboratories ensured the reliability and validity of final study data. It is essential that sponsors

Linear phase formation by noise simulator

International Nuclear Information System (INIS)

Hazi, G.; Por, G.

1998-01-01

A new simulation technique is introduced to study noise propagation in nuclear power plants. Noise processes are considered as time functions, and the dynamic behaviour of the reactor core is modelled by ordinary and partial differential equations. The equations are solved by numerical methods and the results (time series) are considered as virtual measurements. The auto power spectral density and the cross power spectral density of these time series are calculated by traditional techniques. The spectrum obtained is compared with the analytical solution to validate the new simulation approach. After validation, the simulator is expanded to investigate some physical phenomena which are unmanageable by analytical calculations. Propagating disturbances are studied, and the effect of non-flat flux shape on phase curves is demonstrated. Numerical problems also are briefly discussed. (author)

Validity and reliability of a modified english version of the physical activity questionnaire for adolescents.

Science.gov (United States)

Aggio, Daniel; Fairclough, Stuart; Knowles, Zoe; Graves, Lee

2016-01-01

Adaptation of physical activity self-report questionnaires is sometimes required to reflect the activity behaviours of diverse populations. The processes used to modify self-report questionnaires though are typically underreported. This two-phased study used a formative approach to investigate the validity and reliability of the Physical Activity Questionnaire for Adolescents (PAQ-A) in English youth. Phase one examined test content and response process validity and subsequently informed a modified version of the PAQ-A. Phase two assessed the validity and reliability of the modified PAQ-A. In phase one, focus groups (n = 5) were conducted with adolescents (n = 20) to investigate test content and response processes of the original PAQ-A. Based on evidence gathered in phase one, a modified version of the questionnaire was administered to participants (n = 169, 14.5 ± 1.7 years) in phase two. Internal consistency and test-retest reliability were assessed using Cronbach's alpha and intra-class correlations, respectively. Spearman correlations were used to assess associations between modified PAQ-A scores and accelerometer-derived physical activity, self-reported fitness and physical activity self-efficacy. Phase one revealed that the original PAQ-A was unrepresentative for English youth and that item comprehension varied. Contextual and population/cultural-specific modifications were made to the PAQ-A for use in the subsequent phase. In phase two, modified PAQ-A scores had acceptable internal consistency (α = 0.72) and test-retest reliability (ICC = 0.78). Modified PAQ-A scores were significantly associated with objectively assessed moderate-to-vigorous physical activity (r = 0.39), total physical activity (r = 0.42), self-reported fitness (r = 0.35), and physical activity self-efficacy (r = 0.32) (p ≤ 0.01). The modified PAQ-A had acceptable internal consistency and test-retest reliability. Modified PAQ-A scores

Study on two phase flow characteristics in annular pulsed extraction column with different ratio of annular width to column diameter

International Nuclear Information System (INIS)

Qin Wei; Dai Youyuan; Wang Jiading

1994-01-01

Annular pulsed extraction column can successfully provide large throughput and can be made critically safe for fuel reprocessing. This investigation is to study the two phase flow characteristics in annular pulsed extraction column with four different annular width. 30% TBP (in kerosene)-water is used (water as continuous phase). Results show that modified Pratt correlation is valid under the experimental operation conditions for the annular pulsed extraction column. The characteristic velocity U K decreased with the increase of energy input and increased with the increase of the ratio of annular width to column diameter. Flooding velocity correlation is suggested. The deviation of the calculated values from the experimental data is within +20% for four annular width in a pulsed extraction column

The validity of vignettes in cross country health studies

DEFF Research Database (Denmark)

Pozzoli, Dario; Gupta, Nabanita Datta; Kristensen, Nicolai

Cross-country comparisons of subjective assessments may be ham-pered by sub-population speci.c response style. To correct for this, the use of vignettes has become increasingly popular - notably within cross-country health studies. However, the validity of vignettes as a means to re-scale across ...... that the assumption of RC is not innocous and that our extended model improves the fit and significantly changes the cross-country rankings of health vis-á-vis the standard Chopit model.......Cross-country comparisons of subjective assessments may be ham-pered by sub-population speci.c response style. To correct for this, the use of vignettes has become increasingly popular - notably within cross-country health studies. However, the validity of vignettes as a means to re-scale across...

An approach to model validation and model-based prediction -- polyurethane foam case study.

Energy Technology Data Exchange (ETDEWEB)

Dowding, Kevin J.; Rutherford, Brian Milne

2003-07-01

Enhanced software methodology and improved computing hardware have advanced the state of simulation technology to a point where large physics-based codes can be a major contributor in many systems analyses. This shift toward the use of computational methods has brought with it new research challenges in a number of areas including characterization of uncertainty, model validation, and the analysis of computer output. It is these challenges that have motivated the work described in this report. Approaches to and methods for model validation and (model-based) prediction have been developed recently in the engineering, mathematics and statistical literatures. In this report we have provided a fairly detailed account of one approach to model validation and prediction applied to an analysis investigating thermal decomposition of polyurethane foam. A model simulates the evolution of the foam in a high temperature environment as it transforms from a solid to a gas phase. The available modeling and experimental results serve as data for a case study focusing our model validation and prediction developmental efforts on this specific thermal application. We discuss several elements of the ''philosophy'' behind the validation and prediction approach: (1) We view the validation process as an activity applying to the use of a specific computational model for a specific application. We do acknowledge, however, that an important part of the overall development of a computational simulation initiative is the feedback provided to model developers and analysts associated with the application. (2) We utilize information obtained for the calibration of model parameters to estimate the parameters and quantify uncertainty in the estimates. We rely, however, on validation data (or data from similar analyses) to measure the variability that contributes to the uncertainty in predictions for specific systems or units (unit-to-unit variability). (3) We perform statistical

The development and validation of the Clinical Teaching Behavior Inventory (CTBI-23): Nurse preceptors' and new graduate nurses' perceptions of precepting.

Science.gov (United States)

Lee-Hsieh, Jane; O'Brien, Anthony; Liu, Chieh-Yu; Cheng, Su-Fen; Lee, Yea-Wen; Kao, Yu-Hsiu

2016-03-01

Few studies have examined the perceptions of clinical teaching behaviors among both nurse preceptors and preceptees. To develop a Clinical Teaching Behavior Inventory (CTBI) for nurse preceptors' self-evaluation, and for new graduate nurse preceptee evaluation of preceptor clinical teaching behaviors and to test the validity and reliability of the CTBI. This study used mixed research techniques in five phases. Phase I: based on a literature review, the researchers developed an instrument to measure clinical teaching behaviors. Phase II: 17 focus group interviews were conducted with 63 preceptors and 24 new graduate nurses from five hospitals across Taiwan. Clinical teaching behavior themes were extracted from the focus group data and integrated into the domains and items of the CTBI. Phase III: two rounds of an expert Delphi study were conducted to determine the content validity of the instrument. Phase IV: a total of 290 nurse preceptors and 260 new graduate nurses were recruited voluntarily in the same five hospitals in Taiwan. Of these, 521 completed questionnaires to test the construct validity of CTBI by using confirmatory factory analysis. Phase V: the internal consistency and reliability of the instrument were tested. CTBI consists of 23 items in six domains: (1) 'Committing to Teaching'; (2) 'Building a Learning Atmosphere'; (3) 'Using Appropriate Teaching Strategies'; (4) 'Guiding Inter-professional Communication'; (5) 'Providing Feedback and Evaluation'; and (6) 'Showing Concern and Support'. The confirmatory factor analysis yielded a good fit and reliable scores for the CTBI-23 model. The CTBI-23 is a valid and reliable instrument for identifying the clinical teaching behaviors of a preceptor as perceived by preceptors and new graduate preceptees. The CTBI-23 depicts clinical teaching behaviors of nurse preceptors in Taiwan. Copyright © 2015 Elsevier Ltd. All rights reserved.

Online crowdsourcing for efficient rating of speech: a validation study.

Science.gov (United States)

McAllister Byun, Tara; Halpin, Peter F; Szeredi, Daniel

2015-01-01

Blinded listener ratings are essential for valid assessment of interventions for speech disorders, but collecting these ratings can be time-intensive and costly. This study evaluated the validity of speech ratings obtained through online crowdsourcing, a potentially more efficient approach. 100 words from children with /r/ misarticulation were electronically presented for binary rating by 35 phonetically trained listeners and 205 naïve listeners recruited through the Amazon Mechanical Turk (AMT) crowdsourcing platform. Bootstrapping was used to compare different-sized samples of AMT listeners against a "gold standard" (mode across all trained listeners) and an "industry standard" (mode across bootstrapped samples of three trained listeners). There was strong overall agreement between trained and AMT listeners. The "industry standard" level of performance was matched by bootstrapped samples with n = 9 AMT listeners. These results support the hypothesis that valid ratings of speech data can be obtained in an efficient manner through AMT. Researchers in communication disorders could benefit from increased awareness of this method. Readers will be able to (a) discuss advantages and disadvantages of data collection through the crowdsourcing platform Amazon Mechanical Turk (AMT), (b) describe the results of a validity study comparing samples of AMT listeners versus phonetically trained listeners in a speech-rating task. Copyright © 2014 Elsevier Inc. All rights reserved.

Stratified steady and unsteady two-phase flows between two parallel plates

International Nuclear Information System (INIS)

Sim, Woo Gun

2006-01-01

To understand fluid dynamic forces acting on a structure subjected to two-phase flow, it is essential to get detailed information about the characteristics of two-phase flow. Stratified steady and unsteady two-phase flows between two parallel plates have been studied to investigate the general characteristics of the flow related to flow-induced vibration. Based on the spectral collocation method, a numerical approach has been developed for the unsteady two-phase flow. The method is validated by comparing numerical result to analytical one given for a simple harmonic two-phase flow. The flow parameters for the steady two-phase flow, such as void fraction and two-phase frictional multiplier, are evaluated. The dynamic characteristics of the unsteady two-phase flow, including the void fraction effect on the complex unsteady pressure, are illustrated

Progress in IFMIF Engineering Validation and Engineering Design Activities

International Nuclear Information System (INIS)

Heidinger, R.; Knaster, J.; Matsumoto, H.; Sugimoto, M.; Mosnier, A.; Arbeiter, F.; Baluc, N.; Cara, P.; Chel, S.; Facco, A.; Favuzza, P.; Heinzel, V.; Ibarra, A.; Massaut, V.; Micciche, G.; Nitti, F.S.; Theile, J.

2013-01-01

Highlights: ► The IFMIF/EVEDA project has entered into the crucial phase of concluding the Interim IFMIF Engineering Design Report. ► The IFMIF plant configuration has been established with the definition of five IFMIF facilities and of their interfaces. ► Three major prototypes of the IFMIF main systems have been designed and are being manufactured, commissioned and operated. -- Abstract: The International Fusion Materials Irradiation Facility (IFMIF) Engineering Design and Engineering Validation Activities (EVEDA) are being developed in a joint project in the framework of the Broader Approach (BA) Agreement between EU and Japan. This project has now entered into a crucial phase as the engineering design of IFMIF is now being formulated in a series of 3 subsequent phases for delivering an Interim IFMIF Engineering Design Report (IIEDR) by mid of 2013. Content of these phases is explained, including the plant configuration detailing the 5 IFMIF facilities and their systems. Together with the Engineering Design Activities, prototyping sub-projects are pursued in the Engineering Validation Activities which consist of the design, manufacturing and testing of the following prototypical systems: Linear IFMIF Prototype Accelerator (LIPAc), EVEDA Lithium Test Loop (ELTL), and High Flux Test Module (HFTM) with the prototypical helium cooling loop (HELOKA). Highlights are described from recent experiments in the Engineering Validation Activities

Reliability and validity of the foot and ankle outcome score: a validation study from Iran.

Science.gov (United States)

Negahban, Hossein; Mazaheri, Masood; Salavati, Mahyar; Sohani, Soheil Mansour; Askari, Marjan; Fanian, Hossein; Parnianpour, Mohamad

2010-05-01

The aims of this study were to culturally adapt and validate the Persian version of Foot and Ankle Outcome Score (FAOS) and present data on its psychometric properties for patients with different foot and ankle problems. The Persian version of FAOS was developed after a standard forward-backward translation and cultural adaptation process. The sample included 93 patients with foot and ankle disorders who were asked to complete two questionnaires: FAOS and Short-Form 36 Health Survey (SF-36). To determine test-retest reliability, 60 randomly chosen patients completed the FAOS again 2 to 6 days after the first administration. Test-retest reliability and internal consistency were assessed using intraclass correlation coefficient (ICC) and Cronbach's alpha, respectively. To evaluate convergent and divergent validity of FAOS compared to similar and dissimilar concepts of SF-36, the Spearman's rank correlation was used. Dimensionality was determined by assessing item-subscale correlation corrected for overlap. The results of test-retest reliability show that all the FAOS subscales have a very high ICC, ranging from 0.92 to 0.96. The minimum Cronbach's alpha level of 0.70 was exceeded by most subscales. The Spearman's correlation coefficient for convergent construct validity fell within 0.32 to 0.58 for the main hypotheses presented a priori between FAOS and SF-36 subscales. For dimensionality, the minimum Spearman's correlation coefficient of 0.40 was exceeded by most items. In conclusion, the results of our study show that the Persian version of FAOS seems to be suitable for Iranian patients with various foot and ankle problems especially lateral ankle sprain. Future studies are needed to establish stronger psychometric properties for patients with different foot and ankle problems.

Infrared thermography method for fast estimation of phase diagrams

Energy Technology Data Exchange (ETDEWEB)

Palomo Del Barrio, Elena [Université de Bordeaux, Institut de Mécanique et d’Ingénierie, Esplanade des Arts et Métiers, 33405 Talence (France); Cadoret, Régis [Centre National de la Recherche Scientifique, Institut de Mécanique et d’Ingénierie, Esplanade des Arts et Métiers, 33405 Talence (France); Daranlot, Julien [Solvay, Laboratoire du Futur, 178 Av du Dr Schweitzer, 33608 Pessac (France); Achchaq, Fouzia, E-mail: fouzia.achchaq@u-bordeaux.fr [Université de Bordeaux, Institut de Mécanique et d’Ingénierie, Esplanade des Arts et Métiers, 33405 Talence (France)

2016-02-10

Highlights: • Infrared thermography is proposed to determine phase diagrams in record time. • Phase boundaries are detected by means of emissivity changes during heating. • Transition lines are identified by using Singular Value Decomposition techniques. • Different binary systems have been used for validation purposes. - Abstract: Phase change materials (PCM) are widely used today in thermal energy storage applications. Pure PCMs are rarely used because of non adapted melting points. Instead of them, mixtures are preferred. The search of suitable mixtures, preferably eutectics, is often a tedious and time consuming task which requires the determination of phase diagrams. In order to accelerate this screening step, a new method for estimating phase diagrams in record time (1–3 h) has been established and validated. A sample composed by small droplets of mixtures with different compositions (as many as necessary to have a good coverage of the phase diagram) deposited on a flat substrate is first prepared and cooled down to ambient temperature so that all droplets crystallize. The plate is then heated at constant heating rate up to a sufficiently high temperature for melting all the small crystals. The heating process is imaged by using an infrared camera. An appropriate method based on singular values decomposition technique has been developed to analyze the recorded images and to determine the transition lines of the phase diagram. The method has been applied to determine several simple eutectic phase diagrams and the reached results have been validated by comparison with the phase diagrams obtained by Differential Scanning Calorimeter measurements and by thermodynamic modelling.

Development of Creative Behavior Observation Form: A Study on Validity and Reliability

Science.gov (United States)

Dere, Zeynep; Ömeroglu, Esra

2018-01-01

This study, Creative Behavior Observation Form was developed to assess creativity of the children. While the study group on the reliability and validity of Creative Behavior Observation Form was being developed, 257 children in total who were at the ages of 5-6 were used as samples with stratified sampling method. Content Validity Index (CVI) and…

Development and validation of stability indicating studies of ...

African Journals Online (AJOL)

Development and validation of stability indicating studies of paliperidone ... A simple and sensitive stability indicating HPLC method is developed for the ... The developed method was proved adequate for quantitative determination of ... Browse By Country · List All Titles · Free To Read Titles This Journal is Open Access.

Videoconference-based mini mental state examination: a validation study.

Science.gov (United States)

Timpano, Francesca; Pirrotta, Fabio; Bonanno, Lilla; Marino, Silvia; Marra, Angela; Bramanti, Placido; Lanzafame, Pietro

2013-12-01

Neuropsychological testing is a prime criterion of good practice to document cognitive deficits in a rapidly aging population. Telecommunication technologies may overcome limitations related to test administration. We compared performance of the Italian videoconference-based version of the Mini Mental State Examination (VMMSE) with performance of the standard MMSE administered face-to-face (F2F), to validate the Italian version of the 28-item VMMSE. To validate the Italian version of the VMMSE, we compared its performance with standard F2F. The sample (n=342) was administered three VMMSEs within 6 weeks after F2F testing. We identified the optimal cutoff through the receiver operating characteristic curve, as well as the VMMSE consistency through inter- and intrarater reliability (Inter/RR and Intra/RR) analysis. We found high levels of sensitivity and specificity for the optimal VMMSE cutoff identification and an accuracy of 0.96 (95% confidence interval 0.94-0.98). Intra/RR and inter/RR were highly significant. This study demonstrates that VMMSE is a valid instrument in clinical and research screening and monitoring of subjects affected by cognitive disorders. This study shows a significant correlation between videoconference assessment and the F2F one, providing an important impetus to expand studies and the knowledge about the usefulness of tele-assistance services. Our findings have important implications for both longitudinal assistance and clinical care of demented patients.

Development, validation and routine control of a radiation process

International Nuclear Information System (INIS)

Kishor Mehta

2010-01-01

Today, radiation is used in industrial processing for variety of applications; from low doses for blood irradiation to very high doses for materials modification and even higher for gemstone colour enhancement. At present, radiation is mainly provided by either radionuclides or machine sources; cobalt-60 is the most predominant radionuclide in use. Currently, there are several hundred irradiation facilities worldwide. Similar to other industries, quality management systems can assist radiation processing facilities in enhancing customer satisfaction and maintaining and improving product quality. To help fulfill quality management requirements, several national and international organizations have developed various standards related to radiation processing. They all have requirements and guidelines for development, validation and routine control of the radiation process. For radiation processing, these three phases involve the following activities. Development phase includes selecting the type of radiation source, irradiation facility and the dose required for the process. Validation phase includes conducting activities that give assurance that the process will be successful. Routine control then involves activities that provide evidence that the process has been successfully realized. These standards require documentary evidence that process validation and process control have been followed. Dosimetry information gathered during these processes provides this evidence. (authors)

Protocol: validation of the INCODE barometer to measure the innovation compe-tence through the Rasch Measurement Theory

Directory of Open Access Journals (Sweden)

Lidia Sanchez

2017-06-01

Full Text Available This communication presents a protocol in order to show the different phases that must be followed in order to validate the INCODE barometer, which is used to measure the innovation competence, with Rasch Measurement Theory. Five phases are stated: dimensionality analysis, individual reliability and validity analysis of ítems and persons, global reliability and validity analysis, and cathegory analysis.

A proposed best practice model validation framework for banks

Directory of Open Access Journals (Sweden)

Pieter J. (Riaan de Jongh

2017-06-01

Full Text Available Background: With the increasing use of complex quantitative models in applications throughout the financial world, model risk has become a major concern. The credit crisis of 2008–2009 provoked added concern about the use of models in finance. Measuring and managing model risk has subsequently come under scrutiny from regulators, supervisors, banks and other financial institutions. Regulatory guidance indicates that meticulous monitoring of all phases of model development and implementation is required to mitigate this risk. Considerable resources must be mobilised for this purpose. The exercise must embrace model development, assembly, implementation, validation and effective governance. Setting: Model validation practices are generally patchy, disparate and sometimes contradictory, and although the Basel Accord and some regulatory authorities have attempted to establish guiding principles, no definite set of global standards exists. Aim: Assessing the available literature for the best validation practices. Methods: This comprehensive literature study provided a background to the complexities of effective model management and focussed on model validation as a component of model risk management. Results: We propose a coherent ‘best practice’ framework for model validation. Scorecard tools are also presented to evaluate if the proposed best practice model validation framework has been adequately assembled and implemented. Conclusion: The proposed best practice model validation framework is designed to assist firms in the construction of an effective, robust and fully compliant model validation programme and comprises three principal elements: model validation governance, policy and process.

European Validation of the Integral Code ASTEC (EVITA)

International Nuclear Information System (INIS)

Allelein, H.-J.; Neu, K.; Dorsselaere, J.P. Van

2005-01-01

The main objective of the European Validation of the Integral Code ASTEC (EVITA) project is to distribute the severe accident integral code ASTEC to European partners in order to apply the validation strategy issued from the VASA project (4th EC FWP). Partners evaluate the code capability through validation on reference experiments and plant applications accounting for severe accident management measures, and compare results with reference codes. The basis version V0 of ASTEC (Accident Source Term Evaluation Code)-commonly developed and basically validated by GRS and IRSN-was made available in late 2000 for the EVITA partners on their individual platforms. Users' training was performed by IRSN and GRS. The code portability on different computers was checked to be correct. A 'hot line' assistance was installed continuously available for EVITA code users. The actual version V1 has been released to the EVITA partners end of June 2002. It allows to simulate the front-end phase by two new modules:- for reactor coolant system 2-phase simplified thermal hydraulics (5-equation approach) during both front-end and core degradation phases; - for core degradation, based on structure and main models of ICARE2 (IRSN) reference mechanistic code for core degradation and on other simplified models. Next priorities are clearly identified: code consolidation in order to increase the robustness, extension of all plant applications beyond the vessel lower head failure and coupling with fission product modules, and continuous improvements of users' tools. As EVITA has very successfully made the first step into the intention to provide end-users (like utilities, vendors and licensing authorities) with a well validated European integral code for the simulation of severe accidents in NPPs, the EVITA partners strongly recommend to continue validation, benchmarking and application of ASTEC. This work will continue in Severe Accident Research Network (SARNET) in the 6th Framework Programme

Imaging gravity waves in lower stratospheric AMSU-A radiances, Part 2: Validation case study

Directory of Open Access Journals (Sweden)

S. D. Eckermann

2006-01-01

Full Text Available Two-dimensional radiance maps from Channel 9 (~60–90 hPa of the Advanced Microwave Sounding Unit (AMSU-A, acquired over southern Scandinavia on 14 January 2003, show plane-wave-like oscillations with a wavelength λh of ~400–500 km and peak brightness temperature amplitudes of up to 0.9 K. The wave-like pattern is observed in AMSU-A radiances from 8 overpasses of this region by 4 different satellites, revealing a growth in the disturbance amplitude from 00:00 UTC to 12:00 UTC and a change in its horizontal structure between 12:00 UTC and 20:00 UTC. Forecast and hindcast runs for 14 January 2003 using high-resolution global and regional numerical weather prediction (NWP models generate a lower stratospheric mountain wave over southern Scandinavia with peak 90 hPa temperature amplitudes of ~5–7 K at 12:00 UTC and a similar horizontal wavelength, packet width, phase structure and time evolution to the disturbance observed in AMSU-A radiances. The wave's vertical wavelength is ~12 km. These NWP fields are validated against radiosonde wind and temperature profiles and airborne lidar profiles of temperature and aerosol backscatter ratios acquired from the NASA DC-8 during the second SAGE III Ozone Loss and Validation Experiment (SOLVE II. Both the amplitude and phase of the stratospheric mountain wave in the various NWP fields agree well with localized perturbation features in these suborbital measurements. In particular, we show that this wave formed the type II polar stratospheric clouds measured by the DC-8 lidar. To compare directly with the AMSU-A data, we convert these validated NWP temperature fields into swath-scanned brightness temperatures using three-dimensional Channel 9 weighting functions and the actual AMSU-A scan patterns from each of the 8 overpasses of this region. These NWP-based brightness temperatures contain two-dimensional oscillations due to this resolved stratospheric mountain wave that have an amplitude, wavelength

Teachers' Engagement at Work: An International Validation Study

Science.gov (United States)

Klassen, Robert M.; Aldhafri, Said; Mansfield, Caroline F.; Purwanto, Edy; Siu, Angela F. Y.; Wong, Marina W.; Woods-McConney, Amanda

2012-01-01

This study explored the validity of the Utrecht Work Engagement Scale in a sample of 853 practicing teachers from Australia, Canada, China (Hong Kong), Indonesia, and Oman. The authors used multigroup confirmatory factor analysis to test the factor structure and measurement invariance across settings, after which they examined the relationships…

Study of a three-phase flow metering process for oil-water-gas flows; Etude d`un procede de mesure des debits d`un ecoulement triphasique de type eau-huile-gaz

Energy Technology Data Exchange (ETDEWEB)

Boyer, Ch.

1996-11-01

We propose a theoretical and experimental study of a three-phase flow metering process for oil-water-gas flows. The selected process is based on a combination of a mixer, a Venturi and ultrasonic methods. To perform an experimental validation of this process an instrumented set-up for three-phase air-oil-water flows has been designed, conceived and adjusted. An original theoretical model have been built to predict three-phase dispersed flows across a contraction. Once validated with two-phase air-water, oil-water and air-oil-water flows data, this model has been used to solve the Venturi metering problems. After a critical review of the available techniques, the ultrasonic propagation velocity has been selected to determine two-phase liquid-liquid flow composition. Two original models have been developed to describe the ultrasonic propagation with the dispersed phase fraction. The comparison with experimental data in oil-water flows show the superiority of one of the two models, the scattering model. For the void fraction determination in air-water flows, the work of Bensler (1990) based on the ultrasonic attenuation measurement has been extended to take into account the multiple scattering effects. Finally these techniques have been combined to determine the different flow rates in air-water, oil-water flows. For two-phase air-water and oil-water flows the problem is solved and the flow rates are measured with a very good accuracy ({+-} 3%). The results quality obtained with three-phase oil-water-gas flows and the secure theoretical bases allowing their interpretation give us the opportunity to strongly recommend the development of an industrial prototype based on the process we studied. (author) 183 refs.

Radioimmuoassay study of antidigitoxin antibodies in liquid phase and after coupling on a solid phase

International Nuclear Information System (INIS)

Collignon, A.; German, A.; Scherrmann, J.M.; Bourdon, R.

1983-01-01

Antidigitoxin antibodies prepared by immunizing rabbits with a digitoxin-bovine serum albumin conjugate have been studied by radioimmunoassay in the native serum (homogeneous phase antibodies) and after coupling on glass beads (heterogeneous phase antibodies). Homogeneous phase antibodies present a satisfactory titer and affinity constant and react very specifically with digitoxin. Fixation of antibodies on a solid phase induce a loss of their immunoreactivity as it is showed by modification of the inhibition curves, by a greater sensitivity to the chemical structure of the tracer and by a decrease of the affinity constant. Reactionnal kinetic and sensitivity to the incubation temperature are not modified. Heterogeneous phase antibodies present a greater stability. Both antibodies types can be used for a digitoxin radioimmunoassay [fr

Validation Study on a Rapid Method for Simultaneous Determination of Pesticide Residues in Vegetables and Fruits by LC-MS/MS.

Science.gov (United States)

Sato, Tamaki; Miyamoto, Iori; Uemura, Masako; Nakatani, Tadashi; Kakutani, Naoya; Yamano, Tetsuo

2016-01-01

A validation study was carried out on a rapid method for the simultaneous determination of pesticide residues in vegetables and fruits by LC-MS/MS. Preparation of the test solution was performed by a solid-phase extraction technique with QuEChERS (STQ method). Pesticide residues were extracted with acetonitrile using a homogenizer, followed by salting-out and dehydration at the same time. The acetonitrile layer was purified with C18 and PSA mini-columns. The method was assessed for 130 pesticide residues in 14 kinds of vegetables and fruits at the concentration level of 0.01 μg/g according to the method validation guideline of the Ministry of Health, Labour and Welfare of Japan. As a result 75 to 120 pesticide residues were determined satisfactorily in the tested samples. Thus, this method could be useful for a rapid and simultaneous determination of multi-class pesticide residues in various vegetables and fruits.

Physics and Algorithm Enhancements for a Validated MCNP/X Monte Carlo Simulation Tool, Phase VII

International Nuclear Information System (INIS)

McKinney, Gregg W.

2012-01-01

Currently the US lacks an end-to-end (i.e., source-to-detector) radiation transport simulation code with predictive capability for the broad range of DHS nuclear material detection applications. For example, gaps in the physics, along with inadequate analysis algorithms, make it difficult for Monte Carlo simulations to provide a comprehensive evaluation, design, and optimization of proposed interrogation systems. With the development and implementation of several key physics and algorithm enhancements, along with needed improvements in evaluated data and benchmark measurements, the MCNP/X Monte Carlo codes will provide designers, operators, and systems analysts with a validated tool for developing state-of-the-art active and passive detection systems. This project is currently in its seventh year (Phase VII). This presentation will review thirty enhancements that have been implemented in MCNPX over the last 3 years and were included in the 2011 release of version 2.7.0. These improvements include 12 physics enhancements, 4 source enhancements, 8 tally enhancements, and 6 other enhancements. Examples and results will be provided for each of these features. The presentation will also discuss the eight enhancements that will be migrated into MCNP6 over the upcoming year.

29 CFR 1607.5 - General standards for validity studies.

Science.gov (United States)

2010-07-01

...) (hereinafter “A.P.A. Standards”) and standard textbooks and journals in the field of personnel selection. D... market and the job should be considered in the determination of when a validity study is outdated. ...

Validation of a Subchannel Analysis Code MATRA Version 1.0

Energy Technology Data Exchange (ETDEWEB)

Hwang, Dae Hyun; Seo, Kyung Won; Kwon, Hyouk

2008-10-15

A subchannel analysis code MATRA has been developed for the thermal hydraulic analysis of SMART core. The governing equations and important models were established, and validation calculations have been performed for subchannel flow and enthalpy distributions in rod bundles under steady-state conditions. The governing equations of the MATRA were on the basis of integral balance equation of the two-phase mixture. The effects of non-homogeneous and non-equilibrium states were considered by employing the subcooled boiling model and the phasic slip model. Solution scheme and main structure of the MATRA code, as well as the difference of MATRA and COBRA-IV-I codes, were summarized. Eight different test data sets were employed for the validation of the MATRA code. The collected data consisted of single-phase subchannel flow and temperature distribution data, single-phase inlet flow maldistribution data, single-phase partial flow blockage data, and two-phase subchannel flow and enthalpy distribution data. The prediction accuracy as well as the limitation of the MATRA code was evaluated from this analysis.

Development and validation of a reversed-phase HPLC method for simultaneous estimation of clotrimazole and beclomethasone dipropionate in lotion and cream dosage form

Directory of Open Access Journals (Sweden)

Komal R Dhudashia

2013-01-01

Full Text Available Background: The combination of Clotrimazole and Beclomethasone dipropionate is used as anti-fungal and anti-inflammatory for external use in the form of cream and lotion. Aim: A simple, specific, economic, precise, and accurate reversed-phase high performance liquid chromatographic method development for the simultaneous estimation of clotrimazole (CT and beclomethasone dipropionate (BD in lotion and cream formulations. Materials and Methods: The chromatographic separation was achieved on a Kromasil C18 (150 mm × 4.6 mm, 5 μm analytical column. A mixture of acetonitrile-water (70:30, v/v was used as the mobile phase, at a flow rate of 1 ml/min and detector wavelength at 254 nm. The validation of the proposed method was carried out for specificity, linearity, accuracy, precision, limit of detection, limit of quantitation, and system suitability test as per ICH guideline. Results: The retention time of CT and BD was found to be 5.4 and 4 min, respectively. The linear dynamic ranges were from 2-16 μg/ml and 80-640 μg/ml for BD and CT, respectively. Limit of detection and quantification for BD were 0.039 and 0.12 μg/ml, for CT 1.24 and 3.77 μg/ml, respectively. Conclusions: The developed method was validated and found to be simple, specific, accurate and precise and can be used for routine quality control analysis of titled drugs in combination in lotion and cream formulation.

Integrated thermal treatment system study -- Phase 2 results. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Feizollahi, F.; Quapp, W.J.

1996-02-01

This report presents the second phase of a study on thermal treatment technologies. The study consists of a systematic assessment of nineteen thermal treatment alternatives for the contact-handled mixed low-level waste (MLLW) currently stored in the US Department of Energy complex. The treatment alternatives consist of widely varying technologies for safely destroying the hazardous organic components, reducing the volume, and preparing for final disposal of the MLLW. The alternatives considered in Phase 2 were innovative thermal treatments with nine types of primary processing units. Other variations in the study examined the effect of combustion gas, air pollution control system design, and stabilization technology for the treatment residues. The Phase 1 study examined ten initial thermal treatment alternatives. The Phase 2 systems were evaluated in essentially the same manner as the Phase 1 systems. The alternatives evaluated were: rotary kiln, slagging kiln, plasma furnace, plasma gasification, molten salt oxidation, molten metal waste destruction, steam gasification, Joule-heated vitrification, thermal desorption and mediated electrochemical oxidation, and thermal desorption and supercritical water oxidation. The quantities, and physical and chemical compositions, of the input waste used in the Phase 2 systems differ from those in the Phase 1 systems, which were based on a preliminary waste input database developed at the onset of the Integrated Thermal Treatment System study. The inventory database used in the Phase 2 study incorporates the latest US Department of Energy information. All systems, both primary treatment systems and subsystem inputs, have now been evaluated using the same waste input (2,927 lb/hr). 28 refs., 88 figs., 41 tabs.

Integrated thermal treatment system study -- Phase 2 results. Revision 1

International Nuclear Information System (INIS)

Feizollahi, F.; Quapp, W.J.

1996-02-01

This report presents the second phase of a study on thermal treatment technologies. The study consists of a systematic assessment of nineteen thermal treatment alternatives for the contact-handled mixed low-level waste (MLLW) currently stored in the US Department of Energy complex. The treatment alternatives consist of widely varying technologies for safely destroying the hazardous organic components, reducing the volume, and preparing for final disposal of the MLLW. The alternatives considered in Phase 2 were innovative thermal treatments with nine types of primary processing units. Other variations in the study examined the effect of combustion gas, air pollution control system design, and stabilization technology for the treatment residues. The Phase 1 study examined ten initial thermal treatment alternatives. The Phase 2 systems were evaluated in essentially the same manner as the Phase 1 systems. The alternatives evaluated were: rotary kiln, slagging kiln, plasma furnace, plasma gasification, molten salt oxidation, molten metal waste destruction, steam gasification, Joule-heated vitrification, thermal desorption and mediated electrochemical oxidation, and thermal desorption and supercritical water oxidation. The quantities, and physical and chemical compositions, of the input waste used in the Phase 2 systems differ from those in the Phase 1 systems, which were based on a preliminary waste input database developed at the onset of the Integrated Thermal Treatment System study. The inventory database used in the Phase 2 study incorporates the latest US Department of Energy information. All systems, both primary treatment systems and subsystem inputs, have now been evaluated using the same waste input (2,927 lb/hr). 28 refs., 88 figs., 41 tabs

Catch-up validation study of an in vitro skin irritation test method based on an open source reconstructed epidermis (phase II).

Science.gov (United States)

Groeber, F; Schober, L; Schmid, F F; Traube, A; Kolbus-Hernandez, S; Daton, K; Hoffmann, S; Petersohn, D; Schäfer-Korting, M; Walles, H; Mewes, K R

2016-10-01

To replace the Draize skin irritation assay (OECD guideline 404) several test methods based on reconstructed human epidermis (RHE) have been developed and were adopted in the OECD test guideline 439. However, all validated test methods in the guideline are linked to RHE provided by only three companies. Thus, the availability of these test models is dependent on the commercial interest of the producer. To overcome this limitation and thus to increase the accessibility of in vitro skin irritation testing, an open source reconstructed epidermis (OS-REp) was introduced. To demonstrate the capacity of the OS-REp in regulatory risk assessment, a catch-up validation study was performed. The participating laboratories used in-house generated OS-REp to assess the set of 20 reference substances according to the performance standards amending the OECD test guideline 439. Testing was performed under blinded conditions. The within-laboratory reproducibility of 87% and the inter-laboratory reproducibility of 85% prove a high reliability of irritancy testing using the OS-REp protocol. In addition, the prediction capacity was with an accuracy of 80% comparable to previous published RHE based test protocols. Taken together the results indicate that the OS-REp test method can be used as a standalone alternative skin irritation test replacing the OECD test guideline 404. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Numerical simulation and experimental validation of coiled adiabatic capillary tubes

Energy Technology Data Exchange (ETDEWEB)

Garcia-Valladares, O. [Centro de Investigacion en Energia, Universidad Nacional Autonoma de Mexico (UNAM), Apdo. Postal 34, 62580 Temixco, Morelos (Mexico)

2007-04-15

The objective of this study is to extend and validate the model developed and presented in previous works [O. Garcia-Valladares, C.D. Perez-Segarra, A. Oliva, Numerical simulation of capillary tube expansion devices behaviour with pure and mixed refrigerants considering metastable region. Part I: mathematical formulation and numerical model, Applied Thermal Engineering 22 (2) (2002) 173-182; O. Garcia-Valladares, C.D. Perez-Segarra, A. Oliva, Numerical simulation of capillary tube expansion devices behaviour with pure and mixed refrigerants considering metastable region. Part II: experimental validation and parametric studies, Applied Thermal Engineering 22 (4) (2002) 379-391] to coiled adiabatic capillary tube expansion devices working with pure and mixed refrigerants. The discretized governing equations are coupled using an implicit step by step method. A special treatment has been implemented in order to consider transitions (subcooled liquid region, metastable liquid region, metastable two-phase region and equilibrium two-phase region). All the flow variables (enthalpies, temperatures, pressures, vapor qualities, velocities, heat fluxes, etc.) together with the thermophysical properties are evaluated at each point of the grid in which the domain is discretized. The numerical model allows analysis of aspects such as geometry, type of fluid (pure substances and mixtures), critical or non-critical flow conditions, metastable regions, and transient aspects. Comparison of the numerical simulation with a wide range of experimental data presented in the technical literature will be shown in the present article in order to validate the model developed. (author)

A Validity Study of the Self-Esteem Inventory.

Science.gov (United States)

Landis, H. John

Results of this validation study of a slightly modified version of the Coppersmith Self-Esteem Inventory substantiate its use with seventh graders to assess Goal I (concerning self-understanding and appreciation of self-worth) of the Educational Quality Assessment Program in Pennsylvania. Appendixes include the definition and rationale for Goal I,…

Plutonium disposition study phase 1b final report

International Nuclear Information System (INIS)

1993-01-01

This report provides the results of the Westinghouse activities performed as part of the Plutonium Disposition Study Phase 1b. These activities, which took place from May 16, 1993 to September 15, 1993, build upon the work completed in Phase 1a, which concluded on May 15, 1993. In Phase 1a, three Plutonium Disposal Reactor (PDR) options were developed for the disposal of excess weapons grade plutonium from returned and dismantled nuclear weapons. This report documents the results of several tasks that were performed to further knowledge in specific areas leading up to Phase 2 of the PDR Study. The Westinghouse activities for Phase 1b are summarized as follows: (1) resolved technical issues concerning reactor physics including equilibrium cycle calculations, use of gadolinium, moderator temperature coefficient, and others as documented in Section 2.0; (2) analyzed large Westinghouse commercial plants for plutonium disposal; (3) reactor safety issues including the steam line break were resolved, and are included in Section 2.0; (4) several tasks related to the PDR Fuel Cycle were examined; (5) cost and deployment options were examined to determine optimal configuration for both plutonium disposal and tritium production; (6) response to questions from DOE and National Academy of Scientists (NAS) reviewers concerning the PDR Phase 1a report are included in Appendix A

Psychometric validation of patient-reported outcome measures assessing chronic constipation

Directory of Open Access Journals (Sweden)

Nelson LM

2014-09-01

Full Text Available Lauren M Nelson,1 Valerie SL Williams,1 Sheri E Fehnel,1 Robyn T Carson,2 James MacDougall,3 Mollie J Baird,3 Stavros Tourkodimitris,2 Caroline B Kurtz,3 Jeffrey M Johnston31RTI Health Solutions, Durham, NC, USA; 2Forest Research Institute, Jersey City, NJ, USA; 3Ironwood Pharmaceuticals, Cambridge, MA, USABackground: Measures assessing treatment outcomes in previous CC clinical trials have not met the requirements described in the US Food and Drug Administration's guidance on patient-reported outcomes.Aim: Psychometric analyses using data from one Phase IIb study and two Phase III trials of linaclotide for the treatment of chronic constipation (CC were conducted to document the measurement properties of patient-reported CC Symptom Severity Measures.Study methods: Each study had a multicenter, randomized, double-blind, placebo-controlled, parallel-group design, comparing placebo to four doses of oral linaclotide taken once daily for 4 weeks in the Phase IIb dose-ranging study (n=307 and to two doses of linaclotide taken once daily for 12 weeks in the Phase III trials (n=1,272. The CC Symptom Severity Measures addressing bowel function (Bowel Movement Frequency, Stool Consistency, Straining and abdominal symptoms (Bloating, Abdominal Discomfort, Abdominal Pain were administered daily using interactive voice-response system technology. Intraclass correlations, Pearson correlations, factor analyses, F-tests, and effect sizes were computed.Results: The CC Symptom Severity Measures demonstrated satisfactory test–retest reliability and construct validity. Factor analyses indicated one factor for abdominal symptoms and another for bowel symptoms. Known-groups F-tests substantiated the discriminating ability of the CC Symptom Severity Measures. Responsiveness statistics were moderate to strong, indicating that these measures are capable of detecting change.Conclusion: In large studies of CC patients, linaclotide significantly improved abdominal and

A mathematical model for hydrogen evolution in an electrochemical cell and experimental validation

International Nuclear Information System (INIS)

Mahmut D Mat; Yuksel Kaplan; Beycan Ibrahimoglu; Nejat Veziroglu; Rafig Alibeyli; Sadiq Kuliyev

2006-01-01

Electrochemical reaction is largely employed in various industrial areas such as hydrogen production, chlorate process, electroplating, metal purification etc. Most of these processes often take place with gas evaluation on the electrodes. Presence of gas phase in the liquid phase makes the problem two-phase flow which is much knowledge available from heat transfer and fluid mechanics studies. The motivation of this study is to investigate hydrogen release in an electrolysis processes from two-phase flow point of view and investigate effect of gas release on the electrolysis process. Hydrogen evolution, flow field and current density distribution in an electrochemical cell are investigated with a two-phase flow model. The mathematical model involves solutions of transport equations for the variables of each phase with allowance for inter phase transfer of mass and momentum. An experimental set-up is established to collect data to validate and improve the mathematical model. Void fraction is determined from measurement of resistivity changes in the system due to the presence of bubbles. A good agreement is obtained between numerical results and experimental data. (authors)

Development and validation of a patient-reported outcome measure for stroke patients.

Science.gov (United States)

Luo, Yanhong; Yang, Jie; Zhang, Yanbo

2015-05-08

Family support and patient satisfaction with treatment are crucial for aiding in the recovery from stroke. However, current validated stroke-specific questionnaires may not adequately capture the impact of these two variables on patients undergoing clinical trials of new drugs. Therefore, the aim of this study was to develop and evaluate a new stroke patient-reported outcome measure (Stroke-PROM) instrument for capturing more comprehensive effects of stroke on patients participating in clinical trials of new drugs. A conceptual framework and a pool of items for the preliminary Stroke-PROM were generated by consulting the relevant literature and other questionnaires created in China and other countries, and interviewing 20 patients and 4 experts to ensure that all germane parameters were included. During the first item-selection phase, classical test theory and item response theory were applied to an initial scale completed by 133 patients with stroke. During the item-revaluation phase, classical test theory and item response theory were used again, this time with 475 patients with stroke and 104 healthy participants. During the scale assessment phase, confirmatory factor analysis was applied to the final scale of the Stroke-PROM using the same study population as in the second item-selection phase. Reliability, validity, responsiveness and feasibility of the final scale were tested. The final scale of Stroke-PROM contained 46 items describing four domains (physiology, psychology, society and treatment). These four domains were subdivided into 10 subdomains. Cronbach's α coefficients for the four domains ranged from 0.861 to 0.908. Confirmatory factor analysis supported the validity of the final scale, and the model fit index satisfied the criterion. Differences in the Stroke-PROM mean scores were significant between patients with stroke and healthy participants in nine subdomains (P < 0.001), indicating that the scale showed good responsiveness. The Stroke

Clinical validity of delayed recall tests as a gateway biomarker for Alzheimer's disease in the context of a structured 5-phase development framework.

Science.gov (United States)

Cerami, Chiara; Dubois, Bruno; Boccardi, Marina; Monsch, Andreas U; Demonet, Jean Francois; Cappa, Stefano F

2017-04-01

Although Alzheimer's disease criteria promote the use of biomarkers, their maturity in clinical routine still needs to be assessed. In the light of the oncology framework, we conducted a literature review on measures used to assess delayed recall impairment due to medial temporal lobe dysfunction (i.e., free and cued word list recall tests). Ample evidence is available for phases 1 (rationale for use), 2 (discriminative ability), and 3 (early detection ability) for many of the tests in routine use. Evidence about phase 4 (performance in real world) and phase 5 (quantify impact and costs) is yet to come. Administration procedures have been standardized and cutoff scores are well validated in large Alzheimer's disease and mild cognitive impaired series. Some aspects (e.g., different task formats), however, hamper the comparability of results among different populations and the reproducibility between laboratories. No definite guideline for their use can thus be proposed at the moment. Accordingly, the maturity of such markers is not yet sufficient and requires future investigation to promote the proper use of memory measures in clinical settings. Copyright © 2016 Elsevier Inc. All rights reserved.

Analysis of the corium phases by X-ray diffraction; Analyses des phases du corium par diffraction des rayons X

Energy Technology Data Exchange (ETDEWEB)

Trillon, G

2004-07-01

In the framework of the severe accidents R and D studies led by CEA, the better knowledge of the corium behaviour, corium coming from the melting of a nuclear reactor, are fundamental stakes in order to master this kind of accident. Among the available physical properties of the corium, the nature of the final crystalline compounds which have been made during the, cooling gives information about its solidification and its stabilisation. X-Rays Diffraction is the reference method used in order to characterize the corium coming from the different facilities of the European platform PLINIUS of CEA-Cadarache. This work presents the scientific approach that has been followed in order to obtain information both qualitative and quantitative on corium, using X-Rays Diffraction. For instance, a specific method for identifying U{sub 1-x}Zr{sub x}O{sub 2} solid solutions has been developed, and the validity of quantitative analysis of corium crystalline phases using the Rietveld method (with an internal standard), has been tested. This last method has also permitted semi-quantitative measurements of amorphous phases within corium. For these studies, analysis of prototypical corium has been conducted on samples coming from the experiences led on the different facilities of the PLINIUS platform. These analysis allowed for the first time to obtain quantitative data of the corium crystalline phases in order to validate thermodynamic databases and has been used to estimate the thereto-physical properties of the corium. New information on crystalline phases of corium has also been found, especially for the UO{sub 2}-ZrO{sub 2} pseudo binary system. (author)

Development and validation of a combined phased acoustical radiosity and image source model for predicting sound fields in rooms.

Science.gov (United States)

Marbjerg, Gerd; Brunskog, Jonas; Jeong, Cheol-Ho; Nilsson, Erling

2015-09-01

A model, combining acoustical radiosity and the image source method, including phase shifts on reflection, has been developed. The model is denoted Phased Acoustical Radiosity and Image Source Method (PARISM), and it has been developed in order to be able to model both specular and diffuse reflections with complex-valued and angle-dependent boundary conditions. This paper mainly describes the combination of the two models and the implementation of the angle-dependent boundary conditions. It furthermore describes how a pressure impulse response is obtained from the energy-based acoustical radiosity by regarding the model as being stochastic. Three methods of implementation are proposed and investigated, and finally, recommendations are made for their use. Validation of the image source method is done by comparison with finite element simulations of a rectangular room with a porous absorber ceiling. Results from the full model are compared with results from other simulation tools and with measurements. The comparisons of the full model are done for real-valued and angle-independent surface properties. The proposed model agrees well with both the measured results and the alternative theories, and furthermore shows a more realistic spatial variation than energy-based methods due to the fact that interference is considered.

An Assessment of Geological Carbon Storage Options in the Illinois Basin: Validation Phase

Energy Technology Data Exchange (ETDEWEB)

Finley, Robert

2012-12-01

The Midwest Geological Sequestration Consortium (MGSC) assessed the options for geological carbon dioxide (CO{sub 2}) storage in the 155,400 km{sup 2} (60,000 mi{sup 2}) Illinois Basin, which underlies most of Illinois, western Indiana, and western Kentucky. The region has annual CO{sub 2} emissions of about 265 million metric tonnes (292 million tons), primarily from 122 coal-fired electric generation facilities, some of which burn almost 4.5 million tonnes (5 million tons) of coal per year (U.S. Department of Energy, 2010). Validation Phase (Phase II) field tests gathered pilot data to update the Characterization Phase (Phase I) assessment of options for capture, transportation, and storage of CO{sub 2} emissions in three geological sink types: coal seams, oil fields, and saline reservoirs. Four small-scale field tests were conducted to determine the properties of rock units that control injectivity of CO{sub 2}, assess the total storage resources, examine the security of the overlying rock units that act as seals for the reservoirs, and develop ways to control and measure the safety of injection and storage processes. The MGSC designed field test operational plans for pilot sites based on the site screening process, MVA program needs, the selection of equipment related to CO{sub 2} injection, and design of a data acquisition system. Reservoir modeling, computational simulations, and statistical methods assessed and interpreted data gathered from the field tests. Monitoring, Verification, and Accounting (MVA) programs were established to detect leakage of injected CO{sub 2} and ensure public safety. Public outreach and education remained an important part of the project; meetings and presentations informed public and private regional stakeholders of the results and findings. A miscible (liquid) CO{sub 2} flood pilot project was conducted in the Clore Formation sandstone (Mississippian System, Chesterian Series) at Mumford Hills Field in Posey County, southwestern

A Validation Study of the Impression Replica Technique.

Science.gov (United States)

Segerström, Sofia; Wiking-Lima de Faria, Johanna; Braian, Michael; Ameri, Arman; Ahlgren, Camilla

2018-04-17

To validate the well-known and often-used impression replica technique for measuring fit between a preparation and a crown in vitro. The validation consisted of three steps. First, a measuring instrument was validated to elucidate its accuracy. Second, a specimen consisting of male and female counterparts was created and validated by the measuring instrument. Calculations were made for the exact values of three gaps between the male and female. Finally, impression replicas were produced of the specimen gaps and sectioned into four pieces. The replicas were then measured with the use of a light microscope. The values received from measuring the specimen were then compared with the values received from the impression replicas, and the technique was thereby validated. The impression replica technique overvalued all measured gaps. Depending on location of the three measuring sites, the difference between the specimen and the impression replicas varied from 47 to 130 μm. The impression replica technique overestimates gaps within the range of 2% to 11%. The validation of the replica technique enables the method to be used as a reference when testing other methods for evaluating fit in dentistry. © 2018 by the American College of Prosthodontists.

Optimization of X-ray phase-contrast imaging based on in-line holography

International Nuclear Information System (INIS)

Wu Xizeng; Liu Hong; Yan Aimin

2005-01-01

This paper introduces a newly conceived formalism for clinical in-line phase-contrast X-ray imaging. The new formalism applies not only to ideal 'thin' objects analyzed in previous studies, but also applies to the real-world tissues used in actual clinical practice. Moreover we have identified the four clinically important factors that affect phase-contrast characteristics. These factors are: (1) body part attenuation (2) the spatial coherence of incident X-rays from an X-ray tube (3) the polychromatic nature of the X-ray source and (4) radiation dose to patients for clinical applications. Techniques of phase image-reconstruction based on the new X-ray in-line holography theory are discussed. Numerical simulations are described which were used to validate the theory. The design parameters of an optimal clinical phase-contrast mammographic imaging system which were determined based on the new theory, and validated in the simulations, are presented. The theory, image reconstruction algorithms, and numerical simulation techniques presented in this paper can be applied widely to clinical diagnostic X-ray imaging applications

Aging of snubbers in nuclear service: Phase I study results and Phase II plans

International Nuclear Information System (INIS)

Goodman, R.L.; Bush, S.H.; Page, R.E.

1988-01-01

Two major research areas were investigated in the Phase I snubber aging studies. The first area involved a preliminary evaluation of the effects of various aging mechanisms on snubber operation; failure modes of mechanisms were identified and their contributions to aging degradation were assessed relative to other failure modes. The second area involved estimating the efficacy of existing tests and examinations that are intended to determine the effects of aging and degradation. Available data on snubber behavior and operating experience were reviewed, using licensee event reports and other historical data for the 10-year period from 1973 through 1983. Value-impact was considered in terms of (1) exposure of workers to radioactive environments for examination/testing and (2) the cost for expansion of the snubber testing program due to failed snubbers. Results from the Phase I studies identified the need to modify or improve examination and testing procedures to enhance snubber reliability. Based on the results of the Phase I snubber studies, the seals and fluids were identified as the two principal elements affected by aging degradation in hydraulic snubbers. Phase II work, which was initiated in FY 1987, will develop cooperative activities between PNL and operating utilities through the Snubber Utility Group (SNUG), who will work to establish a strong data and experience base for both hydraulic and mechanical snubbers based on actual operating and maintenance history at nuclear power plants. Application guidelines for snubbers will be recommended based on the study results

An Italian multicentre validation study of the coma recovery scale-revised.

Science.gov (United States)

Estraneo, A; Moretta, P; De Tanti, A; Gatta, G; Giacino, J T; Trojano, L

2015-10-01

Rate of misdiagnosis of disorders of consciousness (DoC) can be reduced by employing validated clinical diagnostic tools, such as the Coma Recovery Scale-Revised (CRS-R). An Italian version of the CRS-R has been recently developed, but its applicability across different clinical settings, and its concurrent validity and diagnostic sensitivity have not been estimated yet. To perform a multicentre validation study of the Italian version of the Coma Recovery Scale-Revised (CRS-R). Analysis of inter-rater reliability, concurrent validity and diagnostic sensitivity of the scale. One Intensive Care Unit, 8 Post-acute rehabilitation centres and 2 Long-term facilities Twenty-seven professionals (physicians, N.=11; psychologists, N.=5; physiotherapists, N.=3; speech therapists, N.=6; nurses, N.=2) from 11 Italian Centres. CRS-R and Disability Rating Scale (DRS) applied to 122 patients with clinical diagnosis of Vegetative State (VS) or Minimally Conscious State (MCS). CRS-R has good-to-excellent inter-rater reliability for all subscales, particularly for the communication subscale. The Italian version of the CRS-R showed a high sensitivity and specificity in detecting MCS with reference to clinical consensus diagnosis. The CRS-R showed good concurrent validity with the Disability Rating Scale, which had very low specificity with reference to clinical consensus diagnosis. The Italian version of the CRS-R is a valid scale for use from the sub-acute to chronic stages of DoC. It can be administered reliably by all members of the rehabilitation team with different specialties, levels of experience and settings. The present study promote use of the Italian version of the CRS-R to improve diagnosis of DoC patients, and plan tailored rehabilitation treatment.

Western Wind and Solar Integration Study Phase 2 (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Lew, D.; Brinkman, G.; Ibanez, E.; Kumar, N.; Lefton, S.; Jordan, G.; Venkataraman, S.; King, J.

2013-06-01

This presentation accompanies Phase 2 of the Western Wind and Solar Integration Study, a follow-on to Phase 1, which examined the operational impacts of high penetrations of variable renewable generation on the electric power system in the West and was one of the largest variable generation studies to date. High penetrations of variable generation can induce cycling of fossil-fueled generators. Cycling leads to wear-and-tear costs and changes in emissions. Phase 2 calculated these costs and emissions, and simulated grid operations for a year to investigate the detailed impact of variable generation on the fossil-fueled fleet. The presentation highlights the scope of the study and results.

Validation of analytical method to quality control and the stability study of 0.025 % eyedrops Ketotiphen

International Nuclear Information System (INIS)

Troche Concepcion, Yenilen; Romero Diaz, Jacqueline Aylema; Garcia Penna, Caridad M

2010-01-01

The Ketotiphen eyedrop is prescribed to relief the signs and symptoms of allergic conjunctivitis due to its potent H 1a ntihistaminic effect showing some ability to inhibit the histamine release and other mediators in cases of mastocytosis. The aim of present paper was to develop and validate an analytical method for the high-performance liquid chromatography, to quality control and the stability studies of 0.025 % eyedrop Ketotiphen. Method was based on active principle separation by means of a Lichrosorb RP-18 (5 μm) (250 x 4 mm), with UV detection to 296 nm using a mobile phase including a non-gasified mixture of methanol:buffer-phosphate (75:25; pH 8.5) adding 1 mL of Isopropanol by each 1 000 mL of the previous mixture at a 1.2 mL/min flow velocity. The analytical method was linear, accurate, specific and exact during the study concentrations

Rate constants of hydroxyl radical oxidation of polychlorinated biphenyls in the gas phase: A single−descriptor based QSAR and DFT study

International Nuclear Information System (INIS)

Yang, Zhihui; Luo, Shuang; Wei, Zongsu; Ye, Tiantian; Spinney, Richard; Chen, Dong; Xiao, Ruiyang

2016-01-01

The second‒order rate constants (k) of hydroxyl radical (·OH) with polychlorinated biphenyls (PCBs) in the gas phase are of scientific and regulatory importance for assessing their global distribution and fate in the atmosphere. Due to the limited number of measured k values, there is a need to model the k values for unknown PCBs congeners. In the present study, we developed a quantitative structure–activity relationship (QSAR) model with quantum chemical descriptors using a sequential approach, including correlation analysis, principal component analysis, multi−linear regression, validation, and estimation of applicability domain. The result indicates that the single descriptor, polarizability (α), plays an important role in determining the reactivity with a global standardized function of lnk = −0.054 × α ‒ 19.49 at 298 K. In order to validate the QSAR predicted k values and expand the current k value database for PCBs congeners, an independent method, density functional theory (DFT), was employed to calculate the kinetics and thermodynamics of the gas‒phase ·OH oxidation of 2,4′,5-trichlorobiphenyl (PCB31), 2,2′,4,4′-tetrachlorobiphenyl (PCB47), 2,3,4,5,6-pentachlorobiphenyl (PCB116), 3,3′,4,4′,5,5′-hexachlorobiphenyl (PCB169), and 2,3,3′,4,5,5′,6-heptachlorobiphenyl (PCB192) at 298 K at B3LYP/6–311++G**//B3LYP/6–31 + G** level of theory. The QSAR predicted and DFT calculated k values for ·OH oxidation of these PCB congeners exhibit excellent agreement with the experimental k values, indicating the robustness and predictive power of the single–descriptor based QSAR model we developed. - Highlights: • We developed a single−descriptor based QSAR model for ·OH oxidation of PCBs. • We independently validated the QSAR predicted k values of five PCB congeners with the DFT method. • The QSAR predicted and DFT calculated k for the five PCB congeners exhibit excellent agreement. - We developed a single�

Development and validation of reverse phase high performance liquid chromatography for citral analysis from essential oils.

Science.gov (United States)

Gaonkar, Roopa; Yallappa, S; Dhananjaya, B L; Hegde, Gurumurthy

2016-11-15

Citral is a widely used monoterpene aldehyde in aromatherapy, food and pesticide industries. A new validated reverse phase high performance liquid chromatography (RP - HPLC) procedure for the detection and quantification of cis-trans isomers of citral was developed. The RP-HPLC analysis was carried out using Enable C - 18G column (250×4.6mm, 5μ), with acetonitrile and water (70: 30) mobile phase in isocratic mode at 1mL/min flow. A photodiode array (PDA) detector was set at 233nm for the detection of citral. The method showed linearity, selectivity and accuracy for citral in the range of 3-100μg/mL. In order to compare the new RP-HPLC method with the available methods, one of the commercially available essential oil from Cymbopogon flexuosus was analyzed using new RP-HPLC method and the same was analyzed using GC-MS for the comparison of the method for the detection of citral. The GC-MS analysis was done using mass selective detector (MSD) showed citral content to be of 72.76%; wherein the new method showed to contain that same at 74.98%. To prove the application of the new method, essential oils were extracted from lemongrass, lemon leaves and mosambi peels by steam distillation. The citral content present in the essential and also in the condensate was analyzed. The method was found to be suitable for the analysis of citral in essential oils and water based citral formulations with a very good resolution of its components geranial and neral. Copyright © 2016 Elsevier B.V. All rights reserved.

A validated LC-MS/MS determination method for the illegal food additive rhodamine B: Applications of a pharmacokinetic study in rats.

Science.gov (United States)

Cheng, Yung-Yi; Tsai, Tung-Hu

2016-06-05

Rhodamine B is an illegal and potentially carcinogenic food dye. The aim of this study was to develop a convenient, rapid, and sensitive UHPLC-MS/MS method for pharmacokinetic studies in rats. Rat plasma samples were deproteinized with acetonitrile and separated by UHPLC on a reverse-phase C18e column (100mm×2.1mm, 2μm) using a mobile phase consisting of methanol-5mM ammonium acetate (90:10, v/v). Detection was performed using a triple quadrupole tandem mass spectrometer in the selected reaction monitoring mode at [M](+) ion m/z 443.39→399.28 for rhodamine B and [M+H](+) ion m/z 253.17→238.02 for 5-methoxyflavone as the internal standard. This method was specific and produced linear results over a concentration range of 0.5-100ng/mL, with a lower limit of quantitation of 0.5ng/mL. All validation parameters, including the inter-day, intra-day, matrix effect, recovery, and stability in rat plasma, were acceptable according to the biological method validation guidelines developed by the FDA (2001). This method was successfully applied to a pharmacokinetic study in rats; oral administration of 1mg/kg of rhodamine B yielded a time to maximum concentration (Tmax) of 1.3±0.4h and an elimination half-life of 8.8±1.4h, with a clearance of 229.7±19.4mL/h/kg. These pharmacokinetic results provide a constructive contribution to our understanding of the absorption mechanism of rhodamine B and support additional food safety evaluations. Copyright © 2016 Elsevier B.V. All rights reserved.

Benchmarking of small-signal dynamics of single-phase PLLs

DEFF Research Database (Denmark)

Zhang, Chong; Wang, Xiongfei; Blaabjerg, Frede

2015-01-01

Phase-looked Loop (PLL) is a critical component for the control and grid synchronization of grid-connected power converters. This paper presents a benchmarking study on the small-signal dynamics of three commonly used PLLs for single-phase converters, including enhanced PLL, second......-order generalized integrator based PLL, and the inverse-PLL. First, a unified small-signal model of those PLLs is established for comparing their dynamics. Then, a systematic design guideline for parameters tuning of the PLLs is formulated. To confirm the validity of theoretical analysis, nonlinear time...

Can relaxation interventions reduce anxiety in patients receiving radiotherapy? outcomes and study validity

International Nuclear Information System (INIS)

Elith, C.A.; Perkins, B.A.; Johnson, L.S.; Skelly, M.H.; Dempsey, S.

2001-01-01

This study piloted the use of three relaxation interventions in an attempt to reduce levels of anxiety in patients who are immobilised for radiotherapy treatment of head and neck cancers, as well as trying to validate the study methodology. In addition to receiving normal radiation therapy treatment, 14 patients were assigned to either a control group not receiving the relaxation intervention or one of three validated relaxation intervention techniques; music therapy, aromatherapy or guided imagery. Patients in the intervention groups underwent the relaxation technique daily for the first seven days of treatment. On days 1, 3, 5 and 7 of treatment patients were required to complete the State Anxiety Inventory survey. While caution should be taken in accepting the results due to the small numbers of patients involved in the study and the non-randomised assignment of patients within the study, the results of the study demonstrate a clinically significant reduction in anxiety levels in each of the three relaxation interventions compared to the control group. The study demonstrated good study validity due to the ease of implementation, the unambiguous results generated, and the use of already validated anxiety intersections and measurement tools. Copyright (2001) Australian Institute of Radiography

Development and validation of HPLC analytical method for quantitative determination of metronidazole in human plasma

International Nuclear Information System (INIS)

Safdar, K.A.; Shyum, S.B.; Usman, S.

2016-01-01

The objective of the present study was to develop a simple, rapid and sensitive reversed-phase high performance liquid chromatographic (RP-HPLC) analytical method with UV detection system for the quantitative determination of metronidazole in human plasma. The chromatographic separation was performed by using C18 RP column (250mm X 4.6mm, 5 meu m) as stationary phase and 0.01M potassium dihydrogen phosphate buffered at pH 3.0 and acetonitrile (83:17, v/v) as mobile phase at flow rate of 1.0 ml/min. The UV detection was carried out at 320nm. The method was validated as per the US FDA guideline for bioanalytical method validation and was found to be selective without interferences from mobile phase components, impurities and biological matrix. The method found to be linear over the concentration range of 0.2812 meu g/ml to 18.0 meu g/ml (r2 = 0.9987) with adequate level of accuracy and precision. The samples were found to be stable under various recommended laboratory and storage conditions. Therefore, the method can be used with adequate level of confidence and assurance for bioavailability, bioequivalence and other pharmacokinetic studies of metronidazole in human. (author)

Finite-difference method Stokes solver (FDMSS) for 3D pore geometries: Software development, validation and case studies

Science.gov (United States)

Gerke, Kirill M.; Vasilyev, Roman V.; Khirevich, Siarhei; Collins, Daniel; Karsanina, Marina V.; Sizonenko, Timofey O.; Korost, Dmitry V.; Lamontagne, Sébastien; Mallants, Dirk

2018-05-01

Permeability is one of the fundamental properties of porous media and is required for large-scale Darcian fluid flow and mass transport models. Whilst permeability can be measured directly at a range of scales, there are increasing opportunities to evaluate permeability from pore-scale fluid flow simulations. We introduce the free software Finite-Difference Method Stokes Solver (FDMSS) that solves Stokes equation using a finite-difference method (FDM) directly on voxelized 3D pore geometries (i.e. without meshing). Based on explicit convergence studies, validation on sphere packings with analytically known permeabilities, and comparison against lattice-Boltzmann and other published FDM studies, we conclude that FDMSS provides a computationally efficient and accurate basis for single-phase pore-scale flow simulations. By implementing an efficient parallelization and code optimization scheme, permeability inferences can now be made from 3D images of up to 109 voxels using modern desktop computers. Case studies demonstrate the broad applicability of the FDMSS software for both natural and artificial porous media.

Finite-difference method Stokes solver (FDMSS) for 3D pore geometries: Software development, validation and case studies

KAUST Repository

Gerke, Kirill M.

2018-01-17

Permeability is one of the fundamental properties of porous media and is required for large-scale Darcian fluid flow and mass transport models. Whilst permeability can be measured directly at a range of scales, there are increasing opportunities to evaluate permeability from pore-scale fluid flow simulations. We introduce the free software Finite-Difference Method Stokes Solver (FDMSS) that solves Stokes equation using a finite-difference method (FDM) directly on voxelized 3D pore geometries (i.e. without meshing). Based on explicit convergence studies, validation on sphere packings with analytically known permeabilities, and comparison against lattice-Boltzmann and other published FDM studies, we conclude that FDMSS provides a computationally efficient and accurate basis for single-phase pore-scale flow simulations. By implementing an efficient parallelization and code optimization scheme, permeability inferences can now be made from 3D images of up to 109 voxels using modern desktop computers. Case studies demonstrate the broad applicability of the FDMSS software for both natural and artificial porous media.

Validating and comparing GNSS antenna calibrations

Science.gov (United States)

Kallio, Ulla; Koivula, Hannu; Lahtinen, Sonja; Nikkonen, Ville; Poutanen, Markku

2018-03-01

GNSS antennas have no fixed electrical reference point. The variation of the phase centre is modelled and tabulated in antenna calibration tables, which include the offset vector (PCO) and phase centre variation (PCV) for each frequency according to the elevations and azimuths of the incoming signal. Used together, PCV and PCO reduce the phase observations to the antenna reference point. The remaining biases, called the residual offsets, can be revealed by circulating and rotating the antennas on pillars. The residual offsets are estimated as additional parameters when combining the daily GNSS network solutions with full covariance matrix. We present a procedure for validating the antenna calibration tables. The dedicated test field, called Revolver, was constructed at Metsähovi. We used the procedure to validate the calibration tables of 17 antennas. Tables from the IGS and three different calibration institutions were used. The tests show that we were able to separate the residual offsets at the millimetre level. We also investigated the influence of the calibration tables from the different institutions on site coordinates by performing kinematic double-difference baseline processing of the data from one site with different antenna tables. We found small but significant differences between the tables.

Basic School Skills Inventory-3: Validity and Reliability Study

Science.gov (United States)

Yildiz, F. Ülkü; Çagdas, Aysel; Kayili, Gökhan

2017-01-01

The purpose of this study is to perform the validity-reliability analysis of the three subtests of Basic School Skills Inventory 3--Mathematics, Classroom Behavior and Daily Life skills--and do its adaptation for four to six year-old Turkish children. The sample of the study included 595 four to six year-old Turkish children attending public and…

A Validation Study of the Adolescent Dissociative Experiences Scale

Science.gov (United States)

Keck Seeley, Susan. M.; Perosa, Sandra, L.; Perosa, Linda, M.

2004-01-01

Objective: The purpose of this study was to further the validation process of the Adolescent Dissociative Experiences Scale (A-DES). In this study, a 6-item Likert response format with descriptors was used when responding to the A-DES rather than the 11-item response format used in the original A-DES. Method: The internal reliability and construct…

Measuring social alienation in adolescence: translation and validation of the Jessor and Jessor Social Alienation Scale.

Science.gov (United States)

Safipour, Jalal; Tessma, Mesfin Kassaye; Higginbottom, Gina; Emami, Azita

2010-12-01

The objective of the study is to translate and examine the reliability and validity of the Jessor and Jessor Social Alienation Scale for use in a Swedish context. The study involved four phases of testing: (1) Translation and back-translation; (2) a pilot test to evaluate the translation; (3) reliability testing; and (4) a validity test. Main participants of this study were 446 students (Age = 15-19, SD = 1.01, Mean = 17). Results from the reliability test showed high internal consistency and stability. Face, content and construct validity were demonstrated using experts and confirmatory factor analysis. The results of testing the Swedish version of the alienation scale revealed an acceptable level of reliability and validity, and is appropriate for use in the Swedish context. © 2010 The Authors. Scandinavian Journal of Psychology © 2010 The Scandinavian Psychological Associations.

Injection Drug Use Quality of Life scale (IDUQOL: A validation study

Directory of Open Access Journals (Sweden)

Palepu Anita

2005-07-01

Full Text Available Abstract Background Existing measures of injection drug users' quality of life have focused primarily on health and health-related factors. Clearly, however, quality of life among injection drug users is impacted by a range of unique cultural, socioeconomic, medical, and geographic factors that must also be considered in any measure. The Injection Drug User Quality of Life (IDUQOL scale was designed to capture the unique and individual circumstances that determine quality of life among injection drug users. The overall purpose of the present study was to examine the validity of inferences made from the IDUQOL by examining the (a dimensionality, (b reliability of scores, (c criterion-related validity evidence, and (d both convergent and discriminant validity evidence. Methods An exploratory factor analysis using principal axis factoring in SPSS 12.0 was conducted to determine whether the use of a total score on the IDUQOL was advisable. Reliability of scores from the IDUQOL was obtained using internal consistency and one-week test-retest reliability estimates. Criterion-related validity evidence was gathered using variables such as stability of housing, sex trade involvement, high-risk injection behaviours, involvement in treatment programs, emergency treatment or overdose over the previous six months, hospitalization and emergency treatment over the subsequent six month period post data collection. Convergent and discriminant validity evidence was gathered using measures of life satisfaction, self-esteem, and social desirability. Results The sample consisted of 241 injection drug users ranging in age from 19 to 61 years. Factor analysis supports the use of a total score. Both internal consistency (alpha = .88 and one-week test-retest reliability (r = .78 for IDUQOL total scores were good. Criterion-related, convergent, and discriminant validity evidence supports the interpretation of IDUQOL total scores as measuring a construct consistent with

Study of Strange Quark Mass in CFL Phase

Institute of Scientific and Technical Information of China (English)

LI Xin; L(U) Xiao-Fu

2006-01-01

In this paper we introduce bilocal fields in the global color symmetry model and consider color and electrical neutrality conditions simultaneously to study the effect of strange quark mass Ms for the momentum-dependent condensate of color-flavor locked phase. Consequently we find that there will be a quantum phase transition occurring.

Local gas- and liquid-phase measurements for air-water two-phase flows in a rectangular channel

International Nuclear Information System (INIS)

Zhou, X.; Sun, X.; Williams, M.; Fu, Y.; Liu, Y.

2014-01-01

Local gas- and liquid-phase measurements of various gas-liquid two-phase flows, including bubbly, cap-bubbly, slug, and churn-turbulent flows, were performed in an acrylic vertical channel with a rectangular cross section of 30 mm x 10 mm and height of 3.0 m. All the measurements were carried out at three measurement elevations along the flow channel, with z/D h = 9, 72, and 136, respectively, to study the flow development. The gas-phase velocity, void fraction, and bubble number frequency were measured using a double-sensor conductivity probe. A high-speed imaging system was utilized to perform the flow regime visualization and to provide additional quantitative information of the two-phase flow structure. An image processing scheme was developed to obtain the gas-phase velocity, void fraction, Sauter mean diameter, bubble number density, and interfacial area concentration. The liquid-phase velocity and turbulence measurements were conducted using a particle image velocimetry-planar laser-induced fluorescence (PIV-PLIF) system, which enables whole-field and high-resolution data acquisition. An optical phase separation method, which uses fluorescent particles and optical filtration technique, is adopted to extract the velocity information of the liquid phase. An image pre-processing scheme is imposed on the raw PIV images acquired to remove noises due to the presence of bubble residuals and optically distorted particles in the images captured by the PIV-PLIF system. Due to the better light access and less bubble distortion in the narrow rectangular channel, the PIV-PLIF system were able to perform reasonably well in flows of even higher void fractions as compared to the situations with circular pipe test sections. The flow conditions being studied covered various flow regime transitions, void fractions, and liquid-phase flow Reynolds numbers. The obtained experimental data can also be used to validate two-phase CFD results. (author)

Instrument for assessing mobile technology acceptability in diabetes self-management: a validation and reliability study.

Science.gov (United States)

Frandes, Mirela; Deiac, Anca V; Timar, Bogdan; Lungeanu, Diana

2017-01-01

Nowadays, mobile technologies are part of everyday life, but the lack of instruments to assess their acceptability for the management of chronic diseases makes their actual adoption for this purpose slow. The objective of this study was to develop a survey instrument for assessing patients' attitude toward and intention to use mobile technology for diabetes mellitus (DM) self-management, as well as to identify sociodemographic characteristics and quality of life factors that affect them. We first conducted the documentation and instrument design phases, which were subsequently followed by the pilot study and instrument validation. Afterward, the instrument was administered 103 patients (median age: 37 years; range: 18-65 years) diagnosed with type 1 or type 2 DM, who accepted to participate in the study. The reliability and construct validity were assessed by computing Cronbach's alpha and using factor analysis, respectively. The instrument included statements about the actual use of electronic devices for DM management, interaction between patient and physician, attitude toward using mobile technology, and quality of life evaluation. Cronbach's alpha was 0.9 for attitude toward using mobile technology and 0.97 for attitude toward using mobile device applications for DM self-management. Younger patients (Spearman's ρ =-0.429; P higher education level (Kendall's τ =0.51; P mobile assistive applications for DM control. Moreover, patients with a higher quality of life presented a significantly more positive attitude toward using modern technology (Spearman's ρ =0.466; P mobile technology for DM self-management. Additionally, we found that even if most of the patients showed positive attitude toward mobile applications, only a moderate level of intention to indeed use them was observed. Moreover, the study indicated that barriers were truthfulness and easiness to use.

Development and Validation of a Reversed-Phase Liquid Chromatography Method for the Simultaneous Determination of Indole-3-Acetic Acid, Indole-3-Pyruvic Acid, and Abscisic Acid in Barley (Hordeum vulgare L.

Directory of Open Access Journals (Sweden)

Ilva Nakurte

2012-01-01

 mm I.D with a mobile phase composed of methanol and 1% acetic acid (60 : 40 v/v in isocratic mode at a flow rate of 1 ml min-1. The detection was monitored at 270 nm (ABA and at 282 nm (Ex and 360 nm (Em (IAA, IPA. The developed method was validated in terms of accuracy, precision, linearity, limit of detection, limit of quantification, and robustness. The determined validation parameters are in the commonly acceptable ranges for that kind of analysis.

A simple, sensitive and rapid isocratic reversed-phase high-performance liquid chromatography method for determination and stability study of curcumin in pharmaceutical samples

Science.gov (United States)

Amanolahi, Farjad; Mohammadi, Ali; Kazemi Oskuee, Reza; Nassirli, Hooriyeh; Malaekeh-Nikouei, Bizhan

2017-01-01

Objective: This study was designed to develop and validate a new reversed-phase high-performance liquid chromatography (RP-HPLC) method based on Q2 (R1) International Conference on Harmonization (ICH) guideline for determination of curcumin in pharmaceutical samples. Materials and Methods: The HPLC instrument method was optimized with isocratic elution with acetonitrile: ammonium acetate (45:55, v/v, pH 3.5), C18 column (150 mm×4.6 mm×5 µm particle size) and a flow rate of 1 ml/min in ambient condition and total retention time of 17 min. The volume of injection was set at 20 µl and detection was recorded at 425 nm. The robustness of the method was examined by changing the mobile phase composition, mobile phase pH, and flow rate. Results: The method was validated with respect to precision, accuracy and linearity in a concentration range of 2-100 µg/ml. The limit of detection (LOD) and limit of quantification (LOQ) were 0.25 and 0.5 µg/ml, respectively. The percentage of recovery was 98.9 to 100.5 with relative standard deviation (RSD) < 0.638%. Conclusion: The method was found to be simple, sensitive and rapid for determination of curcumin in pharmaceutical samples and had enough sensitivity to detect degradation product of curcumin produced under photolysis and hydrolysis stress condition. PMID:29062806

Sample Preparation and Extraction in Small Sample Volumes Suitable for Pediatric Clinical Studies: Challenges, Advances, and Experiences of a Bioanalytical HPLC-MS/MS Method Validation Using Enalapril and Enalaprilat

Science.gov (United States)

Burckhardt, Bjoern B.; Laeer, Stephanie

2015-01-01

In USA and Europe, medicines agencies force the development of child-appropriate medications and intend to increase the availability of information on the pediatric use. This asks for bioanalytical methods which are able to deal with small sample volumes as the trial-related blood lost is very restricted in children. Broadly used HPLC-MS/MS, being able to cope with small volumes, is susceptible to matrix effects. The latter restrains the precise drug quantification through, for example, causing signal suppression. Sophisticated sample preparation and purification utilizing solid-phase extraction was applied to reduce and control matrix effects. A scale-up from vacuum manifold to positive pressure manifold was conducted to meet the demands of high-throughput within a clinical setting. Faced challenges, advances, and experiences in solid-phase extraction are exemplarily presented on the basis of the bioanalytical method development and validation of low-volume samples (50 μL serum). Enalapril, enalaprilat, and benazepril served as sample drugs. The applied sample preparation and extraction successfully reduced the absolute and relative matrix effect to comply with international guidelines. Recoveries ranged from 77 to 104% for enalapril and from 93 to 118% for enalaprilat. The bioanalytical method comprising sample extraction by solid-phase extraction was fully validated according to FDA and EMA bioanalytical guidelines and was used in a Phase I study in 24 volunteers. PMID:25873972

Sample Preparation and Extraction in Small Sample Volumes Suitable for Pediatric Clinical Studies: Challenges, Advances, and Experiences of a Bioanalytical HPLC-MS/MS Method Validation Using Enalapril and Enalaprilat

Directory of Open Access Journals (Sweden)

Bjoern B. Burckhardt

2015-01-01

Full Text Available In USA and Europe, medicines agencies force the development of child-appropriate medications and intend to increase the availability of information on the pediatric use. This asks for bioanalytical methods which are able to deal with small sample volumes as the trial-related blood lost is very restricted in children. Broadly used HPLC-MS/MS, being able to cope with small volumes, is susceptible to matrix effects. The latter restrains the precise drug quantification through, for example, causing signal suppression. Sophisticated sample preparation and purification utilizing solid-phase extraction was applied to reduce and control matrix effects. A scale-up from vacuum manifold to positive pressure manifold was conducted to meet the demands of high-throughput within a clinical setting. Faced challenges, advances, and experiences in solid-phase extraction are exemplarily presented on the basis of the bioanalytical method development and validation of low-volume samples (50 μL serum. Enalapril, enalaprilat, and benazepril served as sample drugs. The applied sample preparation and extraction successfully reduced the absolute and relative matrix effect to comply with international guidelines. Recoveries ranged from 77 to 104% for enalapril and from 93 to 118% for enalaprilat. The bioanalytical method comprising sample extraction by solid-phase extraction was fully validated according to FDA and EMA bioanalytical guidelines and was used in a Phase I study in 24 volunteers.

Binary population synthesis study of the supersoft X-ray phase of single degenerate type Ia supernova progenitors

International Nuclear Information System (INIS)

Meng Xiangcun; Yang Wuming

2011-01-01

In the single degenerate (SD) scenario for type Ia supernovae (SNe Ia), a mass-accreting white dwarf is expected to experience a supersoft X-ray source (SSS) phase. However, some recent observations showed that the expected number of mass-accreting WDs is much lower than that predicted from theory, regardless of whether they are in spiral or elliptical galaxies. In this paper, we performed a binary population synthesis study on the relative duration of the SSS phase to their whole mass-increasing phase of WDs leading to SNe Ia. We found that for about 40% of the progenitor systems, the relative duration is shorter than 2% and the evolution of the mean relative duration shows that it is always smaller than 5%, both for young and old SNe Ia. In addition, before the SNe Ia explosions, more than 55% of the progenitor systems were experiencing a dwarf novae phase and no more than 10% were staying in the SSS phase. These results are consistent with the recent observations and imply that both in early- and late-type galaxies, only a small fraction of mass-accreting WDs resulting in SNe Ia contributes to the supersoft X-ray flux. So, although our results are not directly related to the X-ray output of the SN Ia progenitor, the low supersoft X-ray luminosity observed in early type galaxies may not be able to exclude the validity of the SD model. On the contrary, it is evidence to support the SD scenario.

A validation study of the Brief Irrational Thoughts Inventory

NARCIS (Netherlands)

Hoogsteder, L.M.; Wissink, I.B.; Stams, G.J.J.M.; van Horn, J.E.; Hendriks, J.

2014-01-01

This study examines the reliability and validity of the "Brief Irrational Thoughts Inventory" (BITI) in a sample of 256 justice-involved youths. The BITI is a questionnaire used to determine the nature and severity of irrational thoughts related to aggressive (externalizing), sub-assertive

A longitudinal study of women's depression symptom profiles during and after the postpartum phase.

Science.gov (United States)

Fox, Molly; Sandman, Curt A; Davis, Elysia Poggi; Glynn, Laura M

2018-04-01

An issue of critical importance for psychiatry and women's health is whether postpartum depression (PPD) represents a unique condition. The Diagnostic and Statistical Manual of Mental Disorders asserts that major depressive disorder (MDD) may present with peripartum onset, without suggesting any other differences between MDD and PPD. The absence of any distinct features calls into question the nosologic validity of PPD as a diagnostic category. The present study investigates whether symptom profiles differ between PPD and depression occurring outside the postpartum phase. In a prospective, longitudinal study of parturient women (N = 239), we examine the manifestation of depression symptoms. We assess factor structure of symptom profiles, and whether factors are differentially pronounced during and after the postpartum period. Factors were revealed representing: Worry, Emotional/Circadian/Energetic Dysregulation, Somatic/Cognitive, Appetite, Distress Display, and Anger symptoms. The factor structure was validated at postpartum and after-postpartum timepoints. Interestingly, the Worry factor, comprising anxiety and guilt, was significantly more pronounced during the postpartum timepoint, and the Emotional/Circadian/Energetic Dysregulation factor, which contained sadness and anhedonia, was significantly less pronounced during the postpartum period. These results suggest that PPD may be a unique syndrome, necessitating research, diagnosis, and treatment strategies distinct from those for MDD. Results indicate the possibility that Worry is an enhanced feature of PPD compared to depression outside the postpartum period, and the crucial role of sadness/anhedonia in MDD diagnosis may be less applicable to PPD diagnosis. © 2018 Wiley Periodicals, Inc.

A study on Z-phase nucleation in martensitic chromium steels

DEFF Research Database (Denmark)

Golpayegani, Ardeshir; Andrén, Hans-Olof; Danielsen, Hilmar Kjartansson

2008-01-01

, initial stages of precipitation of Z-phase have been studied and characterized using energy-filtered transmission electron microscopy (EFTEM). Vanadium nitrides were found to provide the most suitable nucleation site for Z-phase, since the misfit between the (0 0 1) planes of VN and Z-phase is very small....... Furthermore, such a nucleation site would provide vanadium and nitrogen for the growth of Z-phase. The presence of niobium carbide has also been observed close to Z-phase nucleation sites, indicating niobium to be important for the nucleation and growth of Z-phase....

The Clinical Impression of Severity Index for Parkinson's Disease: international validation study.

Science.gov (United States)

Martínez-Martín, Pablo; Rodríguez-Blázquez, Carmen; Forjaz, Maria João; de Pedro, Jesús

2009-01-30

This study sought to provide further information about the psychometric properties of the Clinical Impression of Severity Index for Parkinson's Disease (CISI-PD), in a large, international, cross-culturally diverse sample. Six hundred and fourteen patients with PD participated in the study. Apart from the CISI-PD, assessments were based on Hoehn & Yahr (HY) staging, the Scales for Outcomes in PD-Motor (SCOPA-M), -Cognition (SCOPA-COG) and -Psychosocial (SCOPA-PS), the Cumulative Illness Rating Scale-Geriatrics, and the Hospital Anxiety and Depression Scale. The total CISI-PD score displayed no floor or ceiling effects. Internal consistency was 0.81, the test-retest intraclass correlation coefficient was 0.84, and item homogeneity was 0.52. Exploratory and confirmatory factor analysis (CFI = 0.99, RMSEA = 0.07) confirmed CISI-PD's unifactorial structure. The CISI-PD showed adequate convergent validity with SCOPA-COG and SCOPA-M (r(S) = 0.46-0.85, respectively) and discriminative validity for HY stages and disease duration (P validation study, thus showing that the CISI-PD is a valid instrument to measure clinical impression of severity in PD. Its simplicity and easy application make it an attractive and useful tool for clinical practice and research.

Validation study of genetic biomarkers of response to TNF inhibitors in rheumatoid arthritis.

Directory of Open Access Journals (Sweden)

Rosario Lopez-Rodriguez

Full Text Available Genetic biomarkers are sought to personalize treatment of patients with rheumatoid arthritis (RA, given their variable response to TNF inhibitors (TNFi. However, no genetic biomaker is yet sufficiently validated. Here, we report a validation study of 18 previously reported genetic biomarkers, including 11 from GWAS of response to TNFi. The validation was attempted in 581 patients with RA that had not been treated with biologic antirheumatic drugs previously. Their response to TNFi was evaluated at 3, 6 and 12 months in two ways: change in the DAS28 measure of disease activity, and according to the EULAR criteria for response to antirheumatic drugs. Association of these parameters with the genotypes, obtained by PCR amplification followed by single-base extension, was tested with regression analysis. These analyses were adjusted for baseline DAS28, sex, and the specific TNFi. However, none of the proposed biomarkers was validated, as none showed association with response to TNFi in our study, even at the time of assessment and with the outcome that showed the most significant result in previous studies. These negative results are notable because this was the first independent validation study for 12 of the biomarkers, and because they indicate that prudence is needed in the interpretation of the proposed biomarkers of response to TNFi even when they are supported by very low p values. The results also emphasize the requirement of independent replication for validation, and the need to search protocols that could increase reproducibility of the biomarkers of response to TNFi.

Development and Validation of High Performance Liquid Chromatography Method for Determination Atorvastatin in Tablet

Science.gov (United States)

Yugatama, A.; Rohmani, S.; Dewangga, A.

2018-03-01

Atorvastatin is the primary choice for dyslipidemia treatment. Due to patent expiration of atorvastatin, the pharmaceutical industry makes copy of the drug. Therefore, the development methods for tablet quality tests involving atorvastatin concentration on tablets needs to be performed. The purpose of this research was to develop and validate the simple atorvastatin tablet analytical method by HPLC. HPLC system used in this experiment consisted of column Cosmosil C18 (150 x 4,6 mm, 5 µm) as the stationary reverse phase chomatography, a mixture of methanol-water at pH 3 (80:20 v/v) as the mobile phase, flow rate of 1 mL/min, and UV detector at wavelength of 245 nm. Validation methods were including: selectivity, linearity, accuracy, precision, limit of detection (LOD), and limit of quantitation (LOQ). The results of this study indicate that the developed method had good validation including selectivity, linearity, accuracy, precision, LOD, and LOQ for analysis of atorvastatin tablet content. LOD and LOQ were 0.2 and 0.7 ng/mL, and the linearity range were 20 - 120 ng/mL.

Reasoning with Inductive Argument Test: A Study of Validity and Reliability

Directory of Open Access Journals (Sweden)

Mehmet Emrah Karadere

2013-11-01

Full Text Available Reasoning with Inductive Argument Test:A Study of Validity and Reliability Objective: The aim of our study is to research reliability and validity and to evaluate the usability of Turkish version of Reasoning with Inductive Argument Test (RIAT in Turkish healty population. Method: 51 healty volunteers who work in Ankara Dıskapi Yildirim Beyazit Research and Training Hospital participated in this study. Reasoning with Inductive Argument Test (RIAT was translated into Turkish by three clinical good knowledge of English. Participants were given a sociodemographic data form, and RIAT were performed by clinicians. To test the reliability of the Turkish version of RIAT, Cronbach’s alpha coefficient was calculated and the halving method was used for the test. Results: The internal consistency of the Reasoning with Inductive Argument Test (RIAT items, Cronbach’s alpha internal consistency coefficient measurements of 0.73 was found to be statistically significant. Spearman-Brown coefficient that determines the reliability of the whole test r=0.74 was found. Kurtosis values of all the items was below 1.5 and the percentages in the second evaluation were mainly lower. At the same time, both change in belief between self produced RIAT options and given RIAT options (p=0.02, z=-2296 as well as changes in beliefs between related and unrelated items for Obsessive Compulsive Disorder (OCD difference (p=0.03, z=-2.199 were significant. Conclusion: The preliminary data obtained from the study of reliability and validity of the scale shows that ‘Reasoning with Inductive Argument Test’ supports reliability and validity in Turkish population.

A Validated Stability-indicating Reverse Phase HPLC Assay Method for the Determination of Memantine Hydrochloride Drug Substance with UV-Detection Using Precolumn Derivatization Technique

Directory of Open Access Journals (Sweden)

Bhavil Narola

2010-01-01

Full Text Available This present paper deals with the development and validation of a stability indicating high performance liquid chromatographic method for the quantitative determination of Memantine hydrochloride. Memantine hydrochloride was derivatized with 0.015 M 9-fluorenylmethyl chloroformate (FMOC and 0.5 M borate buffer solution by keeping it at room temperature for about 20 minutes and the chromatographic separation achieved by injecting 10 μL of the derivatized mixture into a Waters HPLC system with photodiode array detector using a kromasil C18 column (150 × 4.6 mm, 5 μ, The mobile phase consisting of 80% acetonitrile and 20% phosphate buffer solution and a flow rate of 2 milliliter/minute. The Memantine was eluted at approximately 7.5 minutes. The volume of FMOC used in derivatization, concentration of FMOC and derivatization time was optimized and used. Forced degradation studies were performed on bulk sample of Memantine hydrochloride using acid (5.0 Normal (N hydrochloric acid, base (1.0 N sodium hydroxide, oxidation (30% hydrogen peroxide, thermal (105 ° C, photolytic and humidity conditions. The developed LC method was validated with respect to specificity, precision (% RSD about 0.70%, linearity (linearity of range about 70-130 μg/mL, ruggedness (Overall % RSD about 0.35%, stability in analytical solution (Cumulative % RSD about 0.11% after 1450 min. and robustness.

A Validated Stability-indicating Reverse Phase HPLC Assay Method for the Determination of Memantine Hydrochloride Drug Substance with UV-Detection Using Precolumn Derivatization Technique

Directory of Open Access Journals (Sweden)

Bhavil Narola

2010-07-01

Full Text Available This present paper deals with the development and validation of a stability indicating high performance liquid chromatographic method for the quantitative determination of Memantine hydrochloride. Memantine hydrochloride was derivatized with 0.015 M 9-fluorenylmethyl chloroformate (FMOC and 0.5 M borate buffer solution by keeping it at room temperature for about 20 minutes and the chromatographic separation achieved by injecting 10 µL of the derivatized mixture into a Waters HPLC system with photodiode array detector using a kromasil C18 column (150 × 4.6 mm, 5 µ. The mobile phase consisting of 80% acetonitrile and 20% phosphate buffer solution and a flow rate of 2 milliliter/minute. The Memantine was eluted at approximately 7.5 minutes. The volume of FMOC used in derivatization, concentration of FMOC and derivatization time was optimized and used. Forced degradation studies were performed on bulk sample of Memantine hydrochloride using acid (5.0 Normal (N hydrochloric acid, base (1.0 N sodium hydroxide, oxidation (30% hydrogen peroxide, thermal (105°C, photolytic and humidity conditions. The developed LC method was validated with respect to specificity, precision (% RSD about 0.70%, linearity (linearity of range about 70–130 µg/mL, ruggedness (Overall % RSD about 0.35%, stability in analytical solution (Cumulative % RSD about 0.11% after 1450 min. and robustness.

Lumbar segmental instability: a criterion-related validity study of manual therapy assessment

Directory of Open Access Journals (Sweden)

Chapple Cathy

2005-11-01

Full Text Available Abstract Background Musculoskeletal physiotherapists routinely assess lumbar segmental motion during the clinical examination of a patient with low back pain. The validity of manual assessment of segmental motion has not, however, been adequately investigated. Methods In this prospective, multi-centre, pragmatic, diagnostic validity study, 138 consecutive patients with recurrent or chronic low back pain (R/CLBP were recruited. Physiotherapists with post-graduate training in manual therapy performed passive accessory intervertebral motion tests (PAIVMs and passive physiological intervertebral motion tests (PPIVMs. Consenting patients were referred for flexion-extension radiographs. Sagittal angular rotation and sagittal translation of each lumbar spinal motion segment was measured from these radiographs, and compared to a reference range derived from a study of 30 asymptomatic volunteers. Motion beyond two standard deviations from the reference mean was considered diagnostic of rotational lumbar segmental instability (LSI and translational LSI. Accuracy and validity of the clinical assessments were expressed using sensitivity, specificity, and likelihood ratio statistics with 95% confidence intervals (CI. Results Only translation LSI was found to be significantly associated with R/CLBP (p Conclusion This study provides the first evidence reporting the concurrent validity of manual tests for the detection of abnormal sagittal planar motion. PAIVMs and PPIVMs are highly specific, but not sensitive, for the detection of translation LSI. Likelihood ratios resulting from positive test results were only moderate. This research indicates that manual clinical examination procedures have moderate validity for detecting segmental motion abnormality.

GPM GROUND VALIDATION GCPEX SNOW MICROPHYSICS CASE STUDY V1

Data.gov (United States)

National Aeronautics and Space Administration — The GPM Ground Validation GCPEX Snow Microphysics Case Study characterizes the 3-D microphysical evolution and distribution of snow in context of the thermodynamic...

Design of Low-Melting Point Compositions Suitable for Transient Liquid Phase Sintering of PM Steels Based on a Thermodynamic and Kinetic Study

Science.gov (United States)

Bernardo, Elena; de Oro, Raquel; Campos, Mónica; Torralba, José Manuel

2014-04-01

The possibility of tailoring the characteristics of a liquid metal is an important asset in a wide number of processing techniques. For most of these processes, the nature and degree of the interaction between liquid and solid phases are usually a focus of interest since they determine liquid properties such as wettability and infiltration capacity. Particularly, within the powder metallurgy (PM) technology, it is considered one of the key aspects to obtain high performance steels through liquid phase sintering. In this work, it is proved how thermodynamic and kinetics software is a powerful tool to study the liquid/solid interactions. The assessment of different liquid phase promoters for transient liquid phase sintering is addressed through the use of ThermoCalc and DICTRA calculations. Besides melting temperatures, particular attention is given to the solubility phenomena between the phases and the kinetics of these processes. Experimental validation of thermodynamic results is carried out by wetting and infiltration experiments at high temperatures. Compositions presenting different liquid/solid solubility are evaluated and directly correlated to the behavior of the liquid during a real sintering process. Therefore, this work opens the possibility to optimize liquid phase compositions and predict the liquid behavior from the design step, which is considered of high technological value for the PM industry.

Validating the Center for Epidemiological Studies Depression Scale for Children in Rwanda

Science.gov (United States)

Betancourt, Theresa; Scorza, Pamela; Meyers-Ohki, Sarah; Mushashi, Christina; Kayiteshonga, Yvonne; Binagwaho, Agnes; Stulac, Sara; Beardslee, William R.

2012-01-01

Objective: We assessed the validity of the Center for Epidemiological Studies Depression Scale for Children (CES-DC) as a screen for depression in Rwandan children and adolescents. Although the CES-DC is widely used for depression screening in high-income countries, its validity in low-income and culturally diverse settings, including sub-Saharan…

Gaia Science Alerts: Early Validation Phase Data from Gaia

Science.gov (United States)

Walton, Nicholas; Hodgkin, Simon; van Leeuwen, Floor

2015-08-01

The ESA Gaia satellite launched Dec 2013, and after successful completion of its in orbit commissioning in July 2014, begun routine operations, with the aim to accurately measure the astrometric and astrophysical properties of more than a billion stars in our Milky Way.As a significant by product of its observational scanning law, where each point on the sky is observed multiple times (~80 revisits on average) over the nominal 5 year mission, Gaia has significant utility in detecting new transients, both flux (e.g. Supernovae, Flare stars) and positional (e.g. Asteroids).We will present the current status of the Gaia Photometric Science Alerts (PSA) system that has been developed within the Gaia DPAC. The PSA pipeline provides a quick look analysis of the daily data stream from Gaia, and identifies new photometric alerts, from analysis of the object photometric and the low resolution spectro-photometric data. Via a set of filters, those identified as astrophysical in nature, are published to the community. The information provided currently includes positional and flux information.The Gaia Alerts working group has organised a significant early stage followup campaign, providing access to a wide variety of followup facilities. These have been used to provide classification spectra of the Gaia alert candidates, with the early phase data confirming that the alerts issued are indeed largely astrophysical transients, with only a small contamination rate.The presentation will address the early phase issues that have been addressed in localising and classifying alerts in the early phase of Gaia observations (for instance, how lack of early knowledge of the sky as seen by Gaia was mitigated by reference to external image data), and how the alert rate published by the PSA will ramp up towards the end of 2015, with the availability of more Gaia sky data.Information concerning the Gaia alerts system can be found at http://gaia.ac.uk/selected-gaia-science-alerts

Two-phase flow characteristics in BWRs

International Nuclear Information System (INIS)

Katono, Kenichi; Aoyama, Goro; Nagayoshi, Takuji; Yasuda, Kenichi; Nishida, Koji

2014-01-01

Reliable prediction of two-phase flow characteristics is important for safety and economy improvements of BWR plants. We have been developing two-phase flow measurement tools and techniques for BWR thermal hydraulic conditions, such as a 3D time-averaged X-ray CT system, an ultrasonic liquid film sensor and a wire-mesh sensor. We applied the developed items in experiments using the multi-purpose steam-water test facility known as HUSTLE, which can simulate two-phase thermal-hydraulic conditions in a BWR reactor pressure vessel, and we constructed a detailed instrumentation database. We validated a 3D two-phase flow simulator using the database and developed the reactor internal two-phase flow analysis system. (author)

A clinical reasoning model focused on clients' behaviour change with reference to physiotherapists: its multiphase development and validation.

Science.gov (United States)

Elvén, Maria; Hochwälder, Jacek; Dean, Elizabeth; Söderlund, Anne

2015-05-01

A biopsychosocial approach and behaviour change strategies have long been proposed to serve as a basis for addressing current multifaceted health problems. This emphasis has implications for clinical reasoning of health professionals. This study's aim was to develop and validate a conceptual model to guide physiotherapists' clinical reasoning focused on clients' behaviour change. Phase 1 consisted of the exploration of existing research and the research team's experiences and knowledge. Phases 2a and 2b consisted of validation and refinement of the model based on input from physiotherapy students in two focus groups (n = 5 per group) and from experts in behavioural medicine (n = 9). Phase 1 generated theoretical and evidence bases for the first version of a model. Phases 2a and 2b established the validity and value of the model. The final model described clinical reasoning focused on clients' behaviour change as a cognitive, reflective, collaborative and iterative process with multiple interrelated levels that included input from the client and physiotherapist, a functional behavioural analysis of the activity-related target behaviour and the selection of strategies for behaviour change. This unique model, theory- and evidence-informed, has been developed to help physiotherapists to apply clinical reasoning systematically in the process of behaviour change with their clients.

Assessment of gait in toddlers with normal motor development and in hemiplegic children with mild motor impairment: a validity study

Directory of Open Access Journals (Sweden)

Priscilla R. P. Figueiredo

2013-08-01

Full Text Available BACKGROUND: The optimization of gait performance is an important goal in the rehabilitation of children with cerebral palsy (CP who present a prognosis associated with locomotion. Gait analysis using videos captured by digital cameras requires validation. OBJECTIVE: To evaluate the validity of a method that involves the analysis of videos captured using a digital camera for quantifying the temporal parameters of gait in toddlers with normal motor development and children with CP. METHOD: Eleven toddlers with normal motor development and eight children with spastic hemiplegia who were able to walk without assistive devices were asked to walk through a space contained in the visual field of two instruments: a digital camera and a three-dimensional motion analysis system, Qualisys Pro-Reflex. The duration of the stance and swing phases of gait and of the entire gait cycle were calculated by analyzing videos captured by a digital camera and compared to those obtained by Qualisys Pro-Reflex, which is considered a highly accurate system. RESULTS: The Intraclass Correlation Coefficient (ICC demonstrated excellent agreement (ICC>0.90 between the two procedures for all measurements, except for the swing phase of the normal toddlers (ICC=0.35. The standard error of measurement was less than 0.02 seconds for all measures. CONCLUSIONS: The results reveal similarities between the two instruments, suggesting that digital cameras can be valid instruments for quantifying two temporal parameters of gait. This congruence is of clinical and scientific relevance and validates the use of digital cameras as a resource for helping the assessment and documentation of the therapeutic effects of interventions targeted at the gait of children with CP.

New Solid Phases for Estimation of Hormones by Radioimmunoassay Technique

International Nuclear Information System (INIS)

Sheha, R.R.; Ayoub, H.S.M.; Shafik, M.

2013-01-01

The efforts in this study were initiated to develop and validate new solid phases for estimation of hormones by radioimmunoassay (RIA). The study argued the successful application of different hydroxy apatites (HAP) as new solid phases for estimation of Alpha fetoprotein (AFP), Thyroid Stimulating hormone (TSH) and Luteinizing hormone (LH) in human serum. Hydroxy apatites have different alkali earth elements were successfully prepared by a well-controlled co-precipitation method with stoichiometric ratio value 1.67. The synthesized barium and calcium hydroxy apatites were characterized using XRD and Ftir and data clarified the preparation of pure structures of both BaHAP and CaHAP with no evidence on presence of other additional phases. The prepared solid phases were applied in various radioimmunoassay systems for separation of bound and free antigens of AFP, TSH and LH hormones. The preparation of radiolabeled tracer for these antigens was carried out using chloramine-T as oxidizing agent. The influence of different parameters on the activation and coupling of the used apatite particles with the polyclonal antibodies was systematically investigated and the optimum conditions were determined. The assay was reproducible, specific and sensitive enough for regular estimation of the studied hormones. The intra-and inter-assay variation were satisfactory and also the recovery and dilution tests indicated an accurate calibration. The reliability of these apatite particles had been validated by comparing the results that obtained by using commercial kits. The results finally authenticates that hydroxyapatite particles would have a great potential to address the emerging challenge of accurate quantitation in laboratory medical application

The eikonal phase of supersymmetric Coulomb partners

CERN Document Server

Lassaut, M; Lombard, R J

1998-01-01

We investigate the eikonal phase and its systematic corrections for the two supersymmetric Coulomb partners V sub 1 and V sub 2 derived by Amado. Apart from a constant shift of -pi for V sub 1 and -2 pi for V sub 2 , the eikonal phase decay to the eikonal phase of the Coulomb potential as 1/kb. For the potential V sub 2 , which is phase equivalent to the Coulomb potential, this result is only valid at b approx =0 and asymptotically; in the intermediate range, it constitutes a lower limit. (author)

Non-Darcy behavior of two-phase channel flow.

Science.gov (United States)

Xu, Xianmin; Wang, Xiaoping

2014-08-01

We study the macroscopic behavior of two-phase flow in porous media from a phase-field model. A dissipation law is first derived from the phase-field model by homogenization. For simple channel geometry in pore scale, the scaling relation of the averaged dissipation rate with the velocity of the two-phase flow can be explicitly obtained from the model which then gives the force-velocity relation. It is shown that, for the homogeneous channel surface, Dacry's law is still valid with a significantly modified permeability including the contribution from the contact line slip. For the chemically patterned surfaces, the dissipation rate has a non-Darcy linear scaling with the velocity, which is related to a depinning force for the patterned surface. Our result offers a theoretical understanding on the prior observation of non-Darcy behavior for the multiphase flow in either simulations or experiments.

External Validation Study of First Trimester Obstetric Prediction Models (Expect Study I): Research Protocol and Population Characteristics.

Science.gov (United States)

Meertens, Linda Jacqueline Elisabeth; Scheepers, Hubertina Cj; De Vries, Raymond G; Dirksen, Carmen D; Korstjens, Irene; Mulder, Antonius Lm; Nieuwenhuijze, Marianne J; Nijhuis, Jan G; Spaanderman, Marc Ea; Smits, Luc Jm

2017-10-26

A number of first-trimester prediction models addressing important obstetric outcomes have been published. However, most models have not been externally validated. External validation is essential before implementing a prediction model in clinical practice. The objective of this paper is to describe the design of a study to externally validate existing first trimester obstetric prediction models, based upon maternal characteristics and standard measurements (eg, blood pressure), for the risk of pre-eclampsia (PE), gestational diabetes mellitus (GDM), spontaneous preterm birth (PTB), small-for-gestational-age (SGA) infants, and large-for-gestational-age (LGA) infants among Dutch pregnant women (Expect Study I). The results of a pilot study on the feasibility and acceptability of the recruitment process and the comprehensibility of the Pregnancy Questionnaire 1 are also reported. A multicenter prospective cohort study was performed in The Netherlands between July 1, 2013 and December 31, 2015. First trimester obstetric prediction models were systematically selected from the literature. Predictor variables were measured by the Web-based Pregnancy Questionnaire 1 and pregnancy outcomes were established using the Postpartum Questionnaire 1 and medical records. Information about maternal health-related quality of life, costs, and satisfaction with Dutch obstetric care was collected from a subsample of women. A pilot study was carried out before the official start of inclusion. External validity of the models will be evaluated by assessing discrimination and calibration. Based on the pilot study, minor improvements were made to the recruitment process and online Pregnancy Questionnaire 1. The validation cohort consists of 2614 women. Data analysis of the external validation study is in progress. This study will offer insight into the generalizability of existing, non-invasive first trimester prediction models for various obstetric outcomes in a Dutch obstetric population

Development and validation of a rapid reversed-phase HPLC method for the determination of the non-nucleoside reverse transcriptase inhibitor dapivirine from polymeric nanoparticles.

Science.gov (United States)

das Neves, José; Sarmento, Bruno; Amiji, Mansoor M; Bahia, Maria Fernanda

2010-06-05

The objective of this work was to develop and validate a rapid reversed-phase (RP) high-performance liquid chromatography (HPLC) method for the in vitro pharmaceutical characterization of dapivirine-loaded polymeric nanoparticles. Chromatographic runs were performed on a RP C18 column with a mobile phase comprising acetonitrile-0.5% (w/v) triethanolamine solution in isocratic mode (80:20, v/v) at a flow rate of 1 ml/min. Dapivirine was detected at a wavelength of 290 nm. The method was shown to be specific, linear in the range of 1-50 microg/ml (R(2)=0.9998), precise at the intra-day and inter-day levels as reflected by the relative standard deviation values (less than 0.85%), accurate (recovery rate of 100.17+/-0.35%), and robust to changes in the mobile phase and column brand. The detection and quantitation limits were 0.08 and 0.24 microg/ml, respectively. The method was successfully used to determine the loading capacity and association efficiency of dapivirine in poly(lactic-co-glycolic acid)-based nanoparticles and its in vitro release. Copyright (c) 2010 Elsevier B.V. All rights reserved.

Validation study of the Japanese version of the Obsessive-Compulsive Drinking Scale.

Science.gov (United States)

Tatsuzawa, Yasutaka; Yoshimasu, Haruo; Moriyama, Yasushi; Furusawa, Teruyuki; Yoshino, Aihide

2002-02-01

The Obsessive-Compulsive Drinking Scale (OCDS) is a self-rating questionnaire that measures cognitive and behavioral aspects of craving for alcohol. The OCDS consists of two subscales: the obsessive thoughts of drinking subscale (OS) and the compulsive drinking subscale (CS). This study aims to validate the Japanese version of the OCDS. First, internal consistency and discriminant validity were evaluated. Second, a prospective longitudinal 3-month outcome study of 67 patients with alcohol dependence who participated in a relapse prevention program was designed to assess the concurrent and predictive validity of the OCDS. The OCDS demonstrated high internal consistency. The OS had high discriminant validity, while the CS did not. Twenty-three patients (34.3%) dropped out of treatment. These patients had significantly higher OS scores than those who completed the program. At 3 months, the relapse group had significantly higher OCDS scores than the no relapse group. Also, the OCDS score was higher in subjects who had early-onset alcohol dependence than late-onset dependence. The OCDS is useful for evaluating cognitive aspect of craving and predicts dropout and relapse.

Effect of isochronal annealing on phase transformation studies of ...

Indian Academy of Sciences (India)

The mixed phase sample shows higher value of magnetization because of the presence of ferromagnetic γ-Fe2O3 ... 1. Introduction. The study of particle size, phase transformation and micros- ..... The results are in qualitative agreement with ...

Experimental and computational study on thermoelectric generators using thermosyphons with phase change as heat exchangers

International Nuclear Information System (INIS)

Araiz, M.; Martínez, A.; Astrain, D.; Aranguren, P.

2017-01-01

Highlights: • Thermosyphon with phase change heat exchanger computational model. • Construction and experimentation of a prototype. • ±9% of maximum deviation from experimental values of the main outputs. • Influence of the auxiliary equipment on the net power generation. - Abstract: An important issue in thermoelectric generators is the thermal design of the heat exchangers since it can improve their performance by increasing the heat absorbed or dissipated by the thermoelectric modules. Due to its several advantages, compared to conventional dissipation systems, a thermosyphon heat exchanger with phase change is proposed to be placed on the cold side of thermoelectric generators. Some of these advantages are: high heat-transfer rates; absence of moving parts and lack of auxiliary consumption (because fans or pumps are not required); and the fact that these systems are wickless. A computational model is developed to design and predict the behaviour of this heat exchangers. Furthermore, a prototype has been built and tested in order to demonstrate its performance and validate the computational model. The model predicts the thermal resistance of the heat exchanger with a relative error in the interval [−8.09; 7.83] in the 95% of the cases. Finally, the use of thermosyphons with phase change in thermoelectric generators has been studied in a waste-heat recovery application, stating that including them on the cold side of the generators improves the net thermoelectric production by 36% compared to that obtained with finned dissipators under forced convection.

Validating the BISON fuel performance code to integral LWR experiments

Energy Technology Data Exchange (ETDEWEB)

Williamson, R.L., E-mail: Richard.Williamson@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Gamble, K.A., E-mail: Kyle.Gamble@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Perez, D.M., E-mail: Danielle.Perez@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Novascone, S.R., E-mail: Stephen.Novascone@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Pastore, G., E-mail: Giovanni.Pastore@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Gardner, R.J., E-mail: Russell.Gardner@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Hales, J.D., E-mail: Jason.Hales@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Liu, W., E-mail: Wenfeng.Liu@anatech.com [ANATECH Corporation, 5435 Oberlin Dr., San Diego, CA 92121 (United States); Mai, A., E-mail: Anh.Mai@anatech.com [ANATECH Corporation, 5435 Oberlin Dr., San Diego, CA 92121 (United States)

2016-05-15

Highlights: • The BISON multidimensional fuel performance code is being validated to integral LWR experiments. • Code and solution verification are necessary prerequisites to validation. • Fuel centerline temperature comparisons through all phases of fuel life are very reasonable. • Accuracy in predicting fission gas release is consistent with state-of-the-art modeling and the involved uncertainties. • Rod diameter comparisons are not satisfactory and further investigation is underway. - Abstract: BISON is a modern finite element-based nuclear fuel performance code that has been under development at Idaho National Laboratory (INL) since 2009. The code is applicable to both steady and transient fuel behavior and has been used to analyze a variety of fuel forms in 1D spherical, 2D axisymmetric, or 3D geometries. Code validation is underway and is the subject of this study. A brief overview of BISON's computational framework, governing equations, and general material and behavioral models is provided. BISON code and solution verification procedures are described, followed by a summary of the experimental data used to date for validation of Light Water Reactor (LWR) fuel. Validation comparisons focus on fuel centerline temperature, fission gas release, and rod diameter both before and following fuel-clad mechanical contact. Comparisons for 35 LWR rods are consolidated to provide an overall view of how the code is predicting physical behavior, with a few select validation cases discussed in greater detail. Results demonstrate that (1) fuel centerline temperature comparisons through all phases of fuel life are very reasonable with deviations between predictions and experimental data within ±10% for early life through high burnup fuel and only slightly out of these bounds for power ramp experiments, (2) accuracy in predicting fission gas release appears to be consistent with state-of-the-art modeling and with the involved uncertainties and (3) comparison

Development and validation of a RP- HPLC method for the quantitation studies of bromadiolone in Ratitox F

Directory of Open Access Journals (Sweden)

Elena Gabriela Oltean

2011-12-01

Full Text Available An isocratic high-performance liquid chromatography (HPLC procedure was developed for the quantitative determination of bromadiolone (hydroxycoumarins in Ratitox F product – rodenticide. HPLC separation was carried out by reversed phase chromatography ODS 2 Hypersil C18 (250 mm x 4.6 mm i.e.; 5 ìm particle size, held in thermostat at 25°C. The mobile phase consisted of methanol/0.1% aqueous solution phosphoric acid (90/10v/v, with a flow rate of 1 ml/min and with UV detection at 265 nm. In order to validate the method, the following parameters have been investigated- linearity (r2 = 0.9999, range, precision, accuracy, specificity, limit of detection and limit of quantification. The described method can be successfully applied for the analysis of Ratitox F – rodenticide.

The birth satisfaction scale: Turkish adaptation, validation and reliability study

Science.gov (United States)

Cetin, Fatma Cosar; Sezer, Ayse; Merih, Yeliz Dogan

2015-01-01

OBJECTIVE: The objective of this study is to investigate the validity and the reliability of Birth Satisfaction Scale (BSS) and to adapt it into the Turkish language. This scale is used for measuring maternal satisfaction with birth in order to evaluate women’s birth perceptions. METHODS: In this study there were 150 women who attended to inpatient postpartum clinic. The participants filled in an information form and the BSS questionnaire forms. The properties of the scale were tested by conducting reliability and validation analyses. RESULTS: BSS entails 30 Likert-type questions. It was developed by Hollins Martin and Fleming. Total scale scores ranged between 30–150 points. Higher scores from the scale mean increases in birth satisfaction. Three overarching themes were identified in Scale: service provision (home assessment, birth environment, support, relationships with health care professionals); personal attributes (ability to cope during labour, feeling in control, childbirth preparation, relationship with baby); and stress experienced during labour (distress, obstetric injuries, receiving sufficient medical care, obstetric intervention, pain, prolonged labour and baby’s health). Cronbach’s alfa coefficient was 0.62. CONCLUSION: According to the present study, BSS entails 30 Likert-type questions and evaluates women’s birth perceptions. The Turkish version of BSS has been proven to be a valid and a reliable scale. PMID:28058355

A realistic validation study of a new nitrogen multiple-breath washout system.

Directory of Open Access Journals (Sweden)

Florian Singer

Full Text Available BACKGROUND: For reliable assessment of ventilation inhomogeneity, multiple-breath washout (MBW systems should be realistically validated. We describe a new lung model for in vitro validation under physiological conditions and the assessment of a new nitrogen (N(2MBW system. METHODS: The N(2MBW setup indirectly measures the N(2 fraction (F(N2 from main-stream carbon dioxide (CO(2 and side-stream oxygen (O(2 signals: F(N2 = 1-F(O2-F(CO2-F(Argon. For in vitro N(2MBW, a double chamber plastic lung model was filled with water, heated to 37°C, and ventilated at various lung volumes, respiratory rates, and F(CO2. In vivo N(2MBW was undertaken in triplets on two occasions in 30 healthy adults. Primary N(2MBW outcome was functional residual capacity (FRC. We assessed in vitro error (√[difference](2 between measured and model FRC (100-4174 mL, and error between tests of in vivo FRC, lung clearance index (LCI, and normalized phase III slope indices (S(acin and S(cond. RESULTS: The model generated 145 FRCs under BTPS conditions and various breathing patterns. Mean (SD error was 2.3 (1.7%. In 500 to 4174 mL FRCs, 121 (98% of FRCs were within 5%. In 100 to 400 mL FRCs, the error was better than 7%. In vivo FRC error between tests was 10.1 (8.2%. LCI was the most reproducible ventilation inhomogeneity index. CONCLUSION: The lung model generates lung volumes under the conditions encountered during clinical MBW testing and enables realistic validation of MBW systems. The new N(2MBW system reliably measures lung volumes and delivers reproducible LCI values.

Development and validation of climate change system thinking instrument (CCSTI) for measuring system thinking on climate change content

Science.gov (United States)

Meilinda; Rustaman, N. Y.; Firman, H.; Tjasyono, B.

2018-05-01

The Climate Change System Thinking Instrument (CCSTI) is developed to measure a system thinking ability in the concept of climate change. CCSTI is developed in four phase’s development including instrument draft development, validation and evaluation including readable material test, expert validation, and field test. The result of field test is analyzed by looking at the readability score in Cronbach’s alpha test. Draft instrument is tested on college students majoring in Biology Education, Physics Education, and Chemistry Education randomly with a total number of 80 college students. Score of Content Validation Index at 0.86, which means that the CCSTI developed are categorized as very appropriate with question indicators and Cronbach’s alpha about 0.605 which mean categorized undesirable to minimal acceptable. From 45 questions of system thinking, there are 37 valid questions spread in four indicators of system thinking, which are system thinking phase I (pre-requirement), system thinking phase II (basic), system thinking phase III (intermediate), and system thinking phase IV (coherent expert).

Seismic risk analysis in the German risk study phase B

International Nuclear Information System (INIS)

Hasser, D.; Liemersdorf, J.

1989-01-01

The paper discusses some aspects of the seismic risk part of the German risk study for nuclear power plants, phase B. First simplified analyses in phase A of the study allowed a rough classification of structures and systems of the PWR reference plant according to their seismic risk contribution. These studies were extended in phase B using improved models for the dynamic analyses of buildings, structures and components as well as for the probabilistic analyses of seismic loading, failure probabilities and event trees. The methodology of deriving probabilistic seismic load descriptions is explained and compared with the methods in phase A of the study and in other studies. Some details of the linear and nonlinear dynamic analyses of structures are reported, in order to demonstrate the influence of different assumptions for material behavior and failure criteria. The probabilistic structural and event tree analyses are discussed with respect to the distribution assumptions, acceptable simplifications, special results for the PWR reference plant and, finally, the influence of model uncertainties

Seismic risk analyses in the German Risk Study, phase B

International Nuclear Information System (INIS)

Hosser, D.; Liemersdorf, H.

1991-01-01

The paper discusses some aspects of the seismic risk part of the German Risk Study for Nuclear Power Plants, Phase B. First simplified analyses in Phase A of the study allowed only a rough classification of structures and systems of the PWR reference plant according to their seismic risk contribution. These studies were extended in Phase B using improved models for the dynamic analyses of buildings, structures and components as well as for the probabilistic analyses of seismic loading, failure probabilities and event trees. The methodology of deriving probabilistic seismic load descriptions is explained and compared with the methods in Phase A of the study and in other studies. Some details of the linear and nonlinear dynamic analyses of structures are reported in order to demonstrate the influence of different assumptions for material behaviour and failure criteria. The probabilistic structural and event tree analyses are discussed with respect to distribution assumptions, acceptable simplifications and model uncertainties. Some results for the PWR reference plant are given. (orig.)

Construct validity and reliability of a checklist for volleyball serve analysis

Directory of Open Access Journals (Sweden)

Cicero Luciano Alves Costa

2018-03-01

Full Text Available This study aims to investigate the construct validity and reliability of the checklist for qualitative analysis of the overhand serve in Volleyball. Fifty-five male subjects aged 13-17 years participated in the study. The overhand serve was analyzed using the checklist proposed by Meira Junior (2003, which analyzes the pattern of serve movement in four phases: (I initial position, (II ball lifting, (III ball attacking, and (IV finalization. Construct validity was analyzed using confirmatory factorial analysis and reliability through the Cronbach’s alpha coefficient. The construct validity was supported by confirmatory factor analysis with the RMSEA results (0.037 [confidence interval 90% = 0.020-0.040], CFI (0.970 and TLI (0.950 indicating good fit of the model. In relation to reliability, Cronbach’s alpha coefficient was 0.661, being this value considered acceptable. Among the items on the checklist, ball lifting and attacking showed higher factor loadings, 0.69 and 0.99, respectively. In summary, the checklist for the qualitative analysis of the overhand serve of Meira Junior (2003 can be considered a valid and reliable instrument for use in research in the field of Sports Sciences.

A phase field study of strain energy effects on solute–grain boundary interactions

International Nuclear Information System (INIS)

Heo, Tae Wook; Bhattacharyya, Saswata; Chen Longqing

2011-01-01

We have studied strain-induced solute segregation at a grain boundary and the solute drag effect on boundary migration using a phase field model integrating grain boundary segregation and grain structure evolution. The elastic strain energy of a solid solution due to the atomic size mismatch and the coherency elastic strain energy caused by the inhomogeneity of the composition distribution are obtained using Khachaturyan’s microelasticity theory. Strain-induced grain boundary segregation at a static planar boundary is studied numerically and the equilibrium segregation composition profiles are validated using analytical solutions. We then systematically studied the effect of misfit strain on grain boundary migration with solute drag. Our theoretical analysis based on Cahn’s analytical theory shows that enhancement of the drag force with increasing atomic size mismatch stems from both an increase in grain boundary segregation due to the strain energy reduction and misfit strain relaxation near the grain boundary. The results were analyzed based on a theoretical analysis in terms of elastic and chemical drag forces. The optimum condition for solute diffusivity to maximize the drag force under a given driving force was identified.

Main results of the german risk study, phase B

International Nuclear Information System (INIS)

Heuser, F.W.

1988-01-01

Work on the German Risk Study is under contract of the Federal Ministry of Research and Technology. The reference plant for the analysis is the Biblis nuclear power plant, Unit B, a KWU pressurized water reactor of the 1300 MWel class. The plant is in operation since 1976. First results on Phase A of the study have been published in 1979. Investigations on Phase B have been foreseen to endeepen the analysis. The principal purpose of these investigations is to improve and to optimize the plant's safety features on a more realistic basis. Main objectives of Phase B are: - Completeness of accident event tree analysis taking into account further accident initiating events. - Identification and analyses of accident management measures which are adequate to minimize accidental risk. - improvement of the analysis on an as far as possible realistic basis, thereby taking into account recent results of safety research. The paper deals with the most important results of the plant analyses (level 1 and level 2) which have been performed within the scope of Phases B of the study

Phased Startup Initiative Phase 3 and 4 Test Procedure (OCRWM)

International Nuclear Information System (INIS)

PAJUNEN, A.L.

2000-01-01

The purpose of this test procedure is to safely operate the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) with specific fuel canisters, and show that canisters containing fuel can be retrieved from the canister queue, decapped in the Canister Decapper, and loaded into the Primary Clean Machine (PCM) for fuel cleaning; and that fuel can be sorted on the Process Table, then loaded back into fuel canisters and relocated in basin storage. An option is included to load selected elements into multi-canister overpack (MCO) Fuel Baskets. Additional Data are collected during this test, beyond that collected during production operations. These data support qualifying the cleaning performance of the PCM, assessing the quantity of scrap generated during the cleaning, and evaluating the impact of fuel retrieval operations on the Basin water quality. The additional data collected primarily consist of weighing fuel and scrap at selected points in the operation, as well as photographing fuel and scrap as it is processed. The time to perform operations is also monitored for comparison with design predictions. Water quality data are collected to establish a baseline to predict the effectiveness of equipment design for control of contamination and visibility during production operation. The scope of this test procedure is to validate the operation of FRS and IWTS components as a complete system. Fuel canisters shall be processed in accordance with this test procedure such that fuel inspection results are clearly attributed to a particular set of PCM operating parameters. The Phase 3 test sequence processes a minimum of six canisters. Twenty-four contingency canisters have been identified, and will be processed if additional performance data are required. The Phase 4 test sequence processes a minimum of 29 specific canisters. Twenty-nine contingency canisters have been identified for Phase 4 activities and will be processed to complete process validation, if

Validation of general job satisfaction in the Korean Labor and Income Panel Study.

Science.gov (United States)

Park, Shin Goo; Hwang, Sang Hee

2017-01-01

The purpose of this study is to assess the validity and reliability of general job satisfaction (JS) in the Korean Labor and Income Panel Study (KLIPS). We used the data from the 17th wave (2014) of the nationwide KLIPS, which selected a representative panel sample of Korean households and individuals aged 15 or older residing in urban areas. We included in this study 7679 employed subjects (4529 males and 3150 females). The general JS instrument consisted of five items rated on a scale from 1 (strongly disagree) to 5 (strongly agree). The general JS reliability was assessed using the corrected item-total correlation and Cronbach's alpha coefficient. The validity of general JS was assessed using confirmatory factor analysis (CFA) and Pearson's correlation. The corrected item-total correlations ranged from 0.736 to 0.837. Therefore, no items were removed. Cronbach's alpha for general JS was 0.925, indicating excellent internal consistency. The CFA of the general JS model showed a good fit. Pearson's correlation coefficients for convergent validity showed moderate or strong correlations. The results obtained in our study confirm the validity and reliability of general JS.

Parkinsons Disease-related Circulating microRNA Biomarkers——a Validation Study

Directory of Open Access Journals (Sweden)

David Petillo

2015-02-01

Full Text Available Parkinson's disease (PD is the second most common neurodegenerative disease. One of the major challenges in studying this progressive neurological disorder is to identify and develop biomarkers for early detection. Recently, several blood-based microRNA (miRNA biomarkers for PD have been reported. However, follow-up studies with new, independent cohorts have been rare. Previously, we identified a panel of four circulating miRNA biomarkers for PD (miR-1826, miR-450b-3p, miR-505, and miR-626 with biomarker performance of 91% sensitivity and 100% specificity. However, the expression of miR-450b-3p could not be detected in a new, independent validation set. In our current study, we improved the detection power by including a non-biased pre-amplification step in quantitative real-time PCR (qRT-PCR and reevaluated the biomarker performance. We found the panel of four PD-related miRNAs achieved the predictive power of 83% sensitivity and 75% specificity in our validation set. This is the first biomarker validation study of PD which showed reproducibility and robustness of plasma-based circulating miRNAs as molecular biomarkers and qRT-PCR as potential diagnostic assay.

Sample size determination for disease prevalence studies with partially validated data.

Science.gov (United States)

Qiu, Shi-Fang; Poon, Wai-Yin; Tang, Man-Lai

2016-02-01

Disease prevalence is an important topic in medical research, and its study is based on data that are obtained by classifying subjects according to whether a disease has been contracted. Classification can be conducted with high-cost gold standard tests or low-cost screening tests, but the latter are subject to the misclassification of subjects. As a compromise between the two, many research studies use partially validated datasets in which all data points are classified by fallible tests, and some of the data points are validated in the sense that they are also classified by the completely accurate gold-standard test. In this article, we investigate the determination of sample sizes for disease prevalence studies with partially validated data. We use two approaches. The first is to find sample sizes that can achieve a pre-specified power of a statistical test at a chosen significance level, and the second is to find sample sizes that can control the width of a confidence interval with a pre-specified confidence level. Empirical studies have been conducted to demonstrate the performance of various testing procedures with the proposed sample sizes. The applicability of the proposed methods are illustrated by a real-data example. © The Author(s) 2012.

Clinical prediction models for bronchopulmonary dysplasia: a systematic review and external validation study

NARCIS (Netherlands)

Onland, Wes; Debray, Thomas P.; Laughon, Matthew M.; Miedema, Martijn; Cools, Filip; Askie, Lisa M.; Asselin, Jeanette M.; Calvert, Sandra A.; Courtney, Sherry E.; Dani, Carlo; Durand, David J.; Marlow, Neil; Peacock, Janet L.; Pillow, J. Jane; Soll, Roger F.; Thome, Ulrich H.; Truffert, Patrick; Schreiber, Michael D.; van Reempts, Patrick; Vendettuoli, Valentina; Vento, Giovanni; van Kaam, Anton H.; Moons, Karel G.; Offringa, Martin

2013-01-01

Bronchopulmonary dysplasia (BPD) is a common complication of preterm birth. Very different models using clinical parameters at an early postnatal age to predict BPD have been developed with little extensive quantitative validation. The objective of this study is to review and validate clinical

A Validated Reverse Phase HPLC Method for the Determination of Disodium EDTA in Meropenem Drug Substance with UV-Detection using Precolumn Derivatization Technique

Directory of Open Access Journals (Sweden)

Bhavil Narola

2011-01-01

Full Text Available This paper deals with development and validation of a high performance liquid chromatographic method for the quantitative determination of disodium EDTA (Ethylenediaminetetraacetic acid in Meropenem active pharmaceutical ingredient (API. EDTA was derivatized with Ferric chloride solution by heating at 70 ° C in water bath for about 20 minutes and the chromatographic separation achieved by injecting 100 μL of the derivatized mixture into a Waters HPLC system with photodiode array detector using a Phenomenex Luna C18(2 column (250 × 4.6 mm, 5 μ, The mobile phase consisting of 5% methanol and 95% of 0.7 g/L solution of Tetra butyl ammonium bromide and 4.6 g/L solution of sodium acetate trihydrate in water (pH adjusted to 4.0 with the help of acetic acid glacial and a flow rate of 1 milliliter/minute. EDTA eluted at approximately 6 minutes. The method was suitably validated with respect to specificity, linearity of response, precision, accuracy, ruggedness, stability in analytical solution, limit of quantitation and detection and robustness for its intended use.

Validity and reliability of the Palliative Care Transition Measure for Caregivers (PCTM-C).

Science.gov (United States)

D'Angelo, Daniela; Mastroianni, Chiara; Artico, Marco; Biagioli, Valentina; Latina, Roberto; Guarda, Michela; Piredda, Michela; De Marinis, Maria Grazia

2018-01-21

Patients suffering from advanced disease face different care transitions. The transition from acute to palliative care is challenging and may lead to the discontinuity of care. Family caregivers become important sources of information, as patients begin to experience difficulties in coping with emotional transition events. The Care Transition Measure was developed to evaluate care transitions as experienced by the elderly. It has never been used in palliative care. The aim of this study was to test the validity and reliability of a modified version of the Palliative Care Transition Measure, specifically the Palliative Care Transition Measure for Caregivers (PCTM-C). The study included two main phases. Phase I focused on the construction of a modified version of the Palliative Care Transition Measure through two focus groups and by computing the content validity index. Phase II focused on testing the psychometric properties of the PCTM-C on 272 family caregivers through confirmatory factor analysis. Result The content validity index for each of the items was higher than 0.80, whereas that for the scale was 0.95. The model tested with confirmatory factor analysis fitted the data well and confirmed that the transition measures referred to communication, integrated care and a trusting-relationship, and therefore the core dimensions of continuity according to existing conceptual models. The internal consistency was high (Cronbach's alpha = 0.94). Significance of results The PCTM-C proved to be a suitable measure of the quality of such transitions. It may be used in clinical practice as a continuity quality indicator and has the potential to guide interventions to enhance family caregivers' experience of care continuity.

Assessing Cognitive Performance in Badminton Players: A Reproducibility and Validity Study

Directory of Open Access Journals (Sweden)

van de Water Tanja

2017-01-01

Full Text Available Fast reaction and good inhibitory control are associated with elite sports performance. To evaluate the reproducibility and validity of a newly developed Badminton Reaction Inhibition Test (BRIT, fifteen elite (25 ± 4 years and nine non-elite (24 ± 4 years Dutch male badminton players participated in the study. The BRIT measured four components: domain-general reaction time, badminton-specific reaction time, domain-general inhibitory control and badminton-specific inhibitory control. Five participants were retested within three weeks on the badminton-specific components. Reproducibility was acceptable for badminton-specific reaction time (ICC = 0.626, CV = 6% and for badminton-specific inhibitory control (ICC = 0.317, CV = 13%. Good construct validity was shown for badminton-specific reaction time discriminating between elite and non-elite players (F = 6.650, p 0.05. Concurrent validity for domain-general reaction time was good, as it was associated with a national ranking for elite (p = 0.70, p 0.05. In conclusion, reproducibility and validity of inhibitory control assessment was not confirmed, however, the BRIT appears a reproducible and valid measure of reaction time in badminton players. Reaction time measured with the BRIT may provide input for training programs aiming to improve badminton players’ performance.

Assessing Cognitive Performance in Badminton Players: A Reproducibility and Validity Study.

Science.gov (United States)

van de Water, Tanja; Huijgen, Barbara; Faber, Irene; Elferink-Gemser, Marije

2017-01-01

Fast reaction and good inhibitory control are associated with elite sports performance. To evaluate the reproducibility and validity of a newly developed Badminton Reaction Inhibition Test (BRIT), fifteen elite (25 ± 4 years) and nine non-elite (24 ± 4 years) Dutch male badminton players participated in the study. The BRIT measured four components: domain-general reaction time, badminton-specific reaction time, domain-general inhibitory control and badminton-specific inhibitory control. Five participants were retested within three weeks on the badminton-specific components. Reproducibility was acceptable for badminton-specific reaction time (ICC = 0.626, CV = 6%) and for badminton-specific inhibitory control (ICC = 0.317, CV = 13%). Good construct validity was shown for badminton-specific reaction time discriminating between elite and non-elite players (F = 6.650, p 0.05). Concurrent validity for domain-general reaction time was good, as it was associated with a national ranking for elite (p = 0.70, p badminton-specific reaction time, nor both components of inhibitory control (p > 0.05). In conclusion, reproducibility and validity of inhibitory control assessment was not confirmed, however, the BRIT appears a reproducible and valid measure of reaction time in badminton players. Reaction time measured with the BRIT may provide input for training programs aiming to improve badminton players' performance.

Turbulent Scalar Transport Model Validation for High Speed Propulsive Flows, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This effort entails the validation of a RANS turbulent scalar transport model (SFM) for high speed propulsive flows, using new experimental data sets and...

Modelling by partial least squares the relationship between the HPLC mobile phases and analytes on phenyl column.

Science.gov (United States)

Markopoulou, Catherine K; Kouskoura, Maria G; Koundourellis, John E

2011-06-01

Twenty-five descriptors and 61 structurally different analytes have been used on a partial least squares (PLS) to latent structure technique in order to study chromatographically their interaction mechanism on a phenyl column. According to the model, 240 different retention times of the analytes, expressed as Y variable (log k), at different % MeOH mobile-phase concentrations have been correlated with their theoretical most important structural or molecular descriptors. The goodness-of-fit was estimated by the coefficient of multiple determinations r(2) (0.919), and the root mean square error of estimation (RMSEE=0.1283) values with a predictive ability (Q(2)) of 0.901. The model was further validated using cross-validation (CV), validated by 20 response permutations r(2) (0.0, 0.0146), Q(2) (0.0, -0.136) and validated by external prediction. The contribution of certain mechanism interactions between the analytes, the mobile phase and the column, proportional or counterbalancing is also studied. Trying to evaluate the influence on Y of every variable in a PLS model, VIP (variables importance in the projection) plot provides evidence that lipophilicity (expressed as Log D, Log P), polarizability, refractivity and the eluting power of the mobile phase are dominant in the retention mechanism on a phenyl column. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Study of the low pressure (Black Phase) SmS properties

International Nuclear Information System (INIS)

Bordier, G.

1987-03-01

SmS has been studied for its transition from the low pressure black phase to the high pressure intermediate valence phase; but the black phase properties seem to be very rich. The variations which pressure of the low-temperature electronic transport properties show the existence of a semi-metallic phase within the black phase domain in a pressure-temperature diagram, for a pressure above 4 kbar, which corresponds to the so-called B'phase. We study the insulating low pressure phase with a model involving acceptor like states. Using electronic paramagnetic resonance experiments we observe a square symmetry trivalent samarium ion neighbour of a sulfure defect, and magnetically coupled with the lattice. This defect exists in two nearly symmetric configurations and the resonance line broadens with temperature in an actived way. It gives rise to metastable effects yielding conductivity relaxations, analysed with stretched exponential laws, because the defect traps magnetically conduction electrons forming a bound magnetic polaron. The relaxation time at zero field is temperature actived. We develop a phenomenological model that gives the good orders of magnitude for the trapping barrier and for the critical field corresponding to the maximum of the low temperature magnetoresistance [fr

The engineering design evolution of IFMIF: From CDR to EDA phase

Energy Technology Data Exchange (ETDEWEB)

Pérez, Mario, E-mail: mario.perez@ifmif.org

2015-10-15

Highlights: • Brief description of International Fusion Materials Irradiation Facility (IFMIF), its background and scope its Engineering Design and Validation Activities (EVEDA) phase. • Description and justification of the main design evolutions from previous phases; and in particular from the baseline described in the “Comprehensive Design Report” (CDR). - Abstract: The International Fusion Materials Irradiation Facility (IFMIF), presently in its Engineering Design and Engineering Validation Activities (EVEDA) phase, started in 2007 under the framework of the Broader Approach (BA) Agreement between Japanese Government and EURATOM. The mandate assigned was to develop an integrated engineering design of IFMIF together with accompanying sub-projects to validate the major technological challenges that included the construction of either full scale prototypes or cleverly devised scaled down facilities, which are essential to reliably face the construction of IFMIF on schedule and cost. The Engineering Design Activities were accomplished on-schedule with the release of its “Intermediate Engineering Design Report (IIEDR)” in June 2013 compliant with our mandate. This paper highlights the design improvements implemented from the previous Conceptual Design Phase.

Correlation of early-phase 18F-florbetapir (AV-45/Amyvid) PET images to FDG images: preliminary studies

International Nuclear Information System (INIS)

Hsiao, Ing-Tsung; Hsieh, Chia-Ju; Wey, Shiaw-Pyng; Lin, Kun-Ju; Huang, Chin-Chang; Hsu, Wen-Chun; Yen, Tzu-Chen; Kung, Mei-Ping

2012-01-01

18 F-Florbetapir (AV-45/Amyvid) is a novel positron emission tomography (PET) tracer for imaging plaque pathology in Alzheimer's disease (AD), while PET images of fluorodeoxyglucose (FDG) for cerebral glucose metabolism can provide complementary information to amyloid plaque images for diagnosis of AD. The goal of this preliminary study was to investigate the perfusion-like property of relative cerebral blood flow estimates (R 1 ) and summed early-phase AV-45 images [perfusion AV-45 (pAV-45)] and optimize the early time frame for pAV-45. Dynamic AV-45 PET scans (0-180 min) were performed in seven subjects. pAV-45, late-phase AV-45, and FDG images were spatially normalized to the Montreal Neurological Institute template aided by individual MRI images, and the corresponding standardized uptake value ratio (SUVR) was computed. The R 1 images were derived from a simplified reference tissue model. Correlations between regional and voxelwise R 1 and the corresponding FDG images were calculated. An optimization of time frames of pAV-45 was conducted in terms of correlation to FDG images. The optimal early time frame was validated in a separate cohort. The regional distribution in the R 1 images correlated well (R = 0.91) to that of the FDG within subjects. Consistently high correlation was noted across a long range of time frames. The maximal correlation of pAV-45 to FDG SUVR of R = 0.95 was observed at the time frame of 1-6 min, while the peak correlation of R = 0.99 happened at 0-2 min between pAV-45 and R 1 . A similar result was achieved in the validation cohort. Preliminary results showed that the distribution patterns of R 1 and pAV-45 images are highly correlated with normalized FDG images, and the initial 5-min early time frame of 1-6 min is potentially useful in providing complementary FDG-like information to the amyloid plaque density by late-phase AV-45 images. (orig.)

A phase change processor method for solving a one-dimensional phase change problem with convection boundary

Energy Technology Data Exchange (ETDEWEB)

Halawa, E.; Saman, W.; Bruno, F. [Institute for Sustainable Systems and Technologies, School of Advanced Manufacturing and Mechanical Engineering, University of South Australia, Mawson Lakes SA 5095 (Australia)

2010-08-15

A simple yet accurate iterative method for solving a one-dimensional phase change problem with convection boundary is described. The one-dimensional model takes into account the variation in the wall temperature along the direction of the flow as well as the sensible heat during preheating/pre-cooling of the phase change material (PCM). The mathematical derivation of convective boundary conditions has been integrated into a phase change processor (PCP) algorithm that solves the liquid fraction and temperature of the nodes. The algorithm is based on the heat balance at each node as it undergoes heating or cooling which inevitably involves phase change. The paper presents the model and its experimental validation. (author)

Worst-case study for cleaning validation of equipment in the radiopharmaceutical production of lyophilized reagents: Methodology validation of total organic carbon

International Nuclear Information System (INIS)

Porto, Luciana Valeria Ferrari Machado

2015-01-01

Radiopharmaceuticals are defined as pharmaceutical preparations containing a radionuclide in their composition, mostly intravenously administered, and therefore compliance with the principles of Good Manufacturing Practices (GMP) is essential and indispensable. Cleaning validation is a requirement of the current GMP, and consists of documented evidence, which demonstrates that the cleaning procedures are able to remove residues to pre-determined acceptance levels, ensuring that no cross contamination occurs. A simplification of cleaning processes validation is accepted, and consists in choosing a product, called 'worst case', to represent the cleaning processes of all equipment of the same production area. One of the steps of cleaning validation is the establishment and validation of the analytical method to quantify the residue. The aim of this study was to establish the worst case for cleaning validation of equipment in the radiopharmaceutical production of lyophilized reagent (LR) for labeling with 99m Tc, evaluate the use of Total Organic Carbon (TOC) content as indicator of equipment cleaning used in the LR manufacture, validate the method of Non-Purgeable Organic Carbon (NPOC), and perform recovery tests with the product chosen as worst case. Worst case product's choice was based on the calculation of an index called 'Worst Case Index' (WCI), using information about drug solubility, difficulty of cleaning the equipment and occupancy rate of the products in line production. The products indicated 'worst case' was the LR MIBI-TEC. The method validation assays were performed using carbon analyser model TOC-Vwp coupled to an autosampler model ASI-V, both from Shimadzu®, controlled by TOC Control-V software. It was used the direct method for NPOC quantification. The parameters evaluated in the validation method were: system suitability, robustness, linearity, detection limit (DL) and quantification limit (QL), precision

Discriminant validity study of Achilles enthesis ultrasound.

Science.gov (United States)

Expósito Molinero, María Rosa; de Miguel Mendieta, Eugenio

2016-01-01

We want to know if the ultrasound examination of the Achilles tendon in spondyloarthritis is different compared to other rheumatic diseases. We studied 97 patients divided into five groups: rheumatoid arthritis, spondyloarthritis, gout, chondrocalcinosis and osteoarthritis, exploring six elementary lesions in 194 Achilles entheses examined. In our study the total index ultrasonographic Achilles is higher in spondyloarthritis with significant differences. The worst elementary spondyloarthritis lesions for discriminations against other pathologies were calcification. This study aims to demonstrate the discriminant validity of Achilles enthesitis observed by ultrasound in spondyloarthritis compared with other rheumatic diseases that may also have ultrasound abnormalities such enthesis level. Copyright © 2015 Elsevier España, S.L.U. and Sociedad Española de Reumatología y Colegio Mexicano de Reumatología. All rights reserved.

Validation of measurements of Fourier phase and amplitude analysis of technetium99 gated cardiac scans using artificial hearts

International Nuclear Information System (INIS)

Yiannikas, J.; Takatani, S.; MacIntyre, W.J.; Underwood, D.A.; Cook, S.A.; Go, R.T.; Napoli, C.; Nose, Y.

1982-01-01

The use of artificial hearts, developed for total heart replacement programs, allows assessment of the accuracy of measuring the first Fourier component phase and amplitude when applied to gated cardiac technetium 99 scans. In the extreme example of asynchrony of ventricular contraction in coronary artery disease that of ventricular aneurysms, the first Fourier component measurements of amplitude were highly correlated to volume increases suggesting that the calculated amplitude accurately reflects volume changes. The calculated asynchrony using Fourier analysis of the gated technetium 99 studies of two artificial hearts was highly accurate when compared to the predetermined calculation of phase angle difference and hence degree of asynchrony. The studies suggest that measurement of phase and amplitude using the first Fourier component of time-activity waves of gated cardiac technetium 99 studies accurately measure degree of asynchrony and volume changes respectively

The Italian validation of the Salford-Scott Nursing Values Questionnaire.

Science.gov (United States)

Mecugni, Daniela; Albinelli, Patrizia; Pellegrin, Joellemarie; Finotto, Stefano

2015-03-01

To properly direct nursing training and to improve the professional practice to become more effective, it is important to understand students' values. Literature review has shown that there have been changes in students' values in the last 20 years. In contemporary students, a general decrease in altruism has been observed, but also a larger appreciation for honesty toward patients has been declared. The analyzed literature did not find validated tools available in Italian that explore personal and professional values of nursing students. This study was an Italian linguistic and cultural adaptation of a research tool. The authors aimed to validate, for the Italian context, the Salford-Scott Nursing Values Questionnaire, enhanced by Johnson to explore the nursing profession's values. The Beaton Model was used as well as Valmi's. These models require five phases, with the goal of producing a pre-final version of the instrument for it to then be administered to a sample of the target and expert population. The study was approved by the Council of the Nursing Degree University course of the Modena and Reggio Emilia University, Reggio Emilia site, and the identity of the subjects was protected at every moment of the testing. Face validation was achieved since the clarity percentile for each item was 100%. Content validity was also reached, measured from the content validity index and the scale validity index. The study has confirmed the reliability of the instrument's internal consistence with a value of Cronbach's alpha on 0.95 of total of items. The reliability of the test-retest confirms the stability of the instrument in time (r = 0.908; p = 0.01). The study concludes that the instrument is ready to be administered to the target population, a sample group of nursing students. © The Author(s) 2014.