WorldWideScience

Sample records for validation safety codes

  1. Validation and verification plan for safety and PRA codes

    International Nuclear Information System (INIS)

    Ades, M.J.; Crowe, R.D.; Toffer, H.

    1991-04-01

    This report discusses a verification and validation (V ampersand V) plan for computer codes used for safety analysis and probabilistic risk assessment calculations. The present plan fulfills the commitments by Westinghouse Savannah River Company (WSRC) to the Department of Energy Savannah River Office (DOE-SRO) to bring the essential safety analysis and probabilistic risk assessment codes in compliance with verification and validation requirements

  2. WSRC approach to validation of criticality safety computer codes

    International Nuclear Information System (INIS)

    Finch, D.R.; Mincey, J.F.

    1991-01-01

    Recent hardware and operating system changes at Westinghouse Savannah River Site (WSRC) have necessitated review of the validation for JOSHUA criticality safety computer codes. As part of the planning for this effort, a policy for validation of JOSHUA and other criticality safety codes has been developed. This policy will be illustrated with the steps being taken at WSRC. The objective in validating a specific computational method is to reliably correlate its calculated neutron multiplication factor (K eff ) with known values over a well-defined set of neutronic conditions. Said another way, such correlations should be: (1) repeatable; (2) demonstrated with defined confidence; and (3) identify the range of neutronic conditions (area of applicability) for which the correlations are valid. The general approach to validation of computational methods at WSRC must encompass a large number of diverse types of fissile material processes in different operations. Special problems are presented in validating computational methods when very few experiments are available (such as for enriched uranium systems with principal second isotope 236 U). To cover all process conditions at WSRC, a broad validation approach has been used. Broad validation is based upon calculation of many experiments to span all possible ranges of reflection, nuclide concentrations, moderation ratios, etc. Narrow validation, in comparison, relies on calculations of a few experiments very near anticipated worst-case process conditions. The methods and problems of broad validation are discussed

  3. Validation of thermal hydraulic codes for fusion reactors safety

    International Nuclear Information System (INIS)

    Sardain, P.; Gulden, W.; Massaut, V.; Takase, K.; Merill, B.; Caruso, G.

    2006-01-01

    A significant effort has been done worldwide on the validation of thermal hydraulic codes, which can be used for the safety assessment of fusion reactors. This work is an item of an implementing agreement under the umbrella of the International Energy Agency. The European part is supported by EFDA. Several programmes related to transient analysis in water-cooled fusion reactors were run in order to assess the capabilities of the codes to treat the main physical phenomena governing the accidental sequences related to water/steam discharge into the vacuum vessel or the cryostat. The typical phenomena are namely the pressurization of a volume at low initial pressure, the critical flow, the flashing, the relief into an expansion volume, the condensation of vapor in a pressure suppression system, the formation of ice on a cryogenic structure, the heat transfer between walls and fluid in various thermodynamic conditions. · A benchmark exercise has been done involving different types of codes, from homogeneous equilibrium to six equations non-equilibrium models. Several cases were defined, each one focusing on a particular phenomenon. · The ICE (Ingress of Coolant Event) facility has been operated in Japan. It has simulated an in-vessel LOCA and the discharge of steam into a pressure suppression system. · The EVITA (European Vacuum Impingement Test Apparatus) facility has been operated in France. It has simulated ingress of coolant into the cryostat, i.e. into a volume at low initial pressure containing surfaces at cryogenic temperature. This paper gives the main lessons gained from these programs, in particular the possibilities for the improvement of the computer codes, extending their capabilities. For example, the water properties have been extended below the triple point. Ice formation models have been implemented. Work has also been done on condensation models. The remaining needs for R-and-D are also highlighted. (author)

  4. Validation of computer codes used in the safety analysis of Canadian research reactors

    International Nuclear Information System (INIS)

    Bishop, W.E.; Lee, A.G.

    1998-01-01

    AECL has embarked on a validation program for the suite of computer codes that it uses in performing the safety analyses for its research reactors. Current focus is on codes used for the analysis of the two MAPLE reactors under construction at Chalk River but the program will be extended to include additional codes that will be used for the Irradiation Research Facility. The program structure is similar to that used for the validation of codes used in the safety analyses for CANDU power reactors. (author)

  5. System code improvements for modelling passive safety systems and their validation

    Energy Technology Data Exchange (ETDEWEB)

    Buchholz, Sebastian; Cron, Daniel von der; Schaffrath, Andreas [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Garching (Germany)

    2016-11-15

    GRS has been developing the system code ATHLET over many years. Because ATHLET, among other codes, is widely used in nuclear licensing and supervisory procedures, it has to represent the current state of science and technology. New reactor concepts such as Generation III+ and IV reactors and SMR are using passive safety systems intensively. The simulation of passive safety systems with the GRS system code ATHLET is still a big challenge, because of non-defined operation points and self-setting operation conditions. Additionally, the driving forces of passive safety systems are smaller and uncertainties of parameters have a larger impact than for active systems. This paper addresses the code validation and qualification work of ATHLET on the example of slightly inclined horizontal heat exchangers, which are e. g. used as emergency condensers (e. g. in the KERENA and the CAREM) or as heat exchanger in the passive auxiliary feed water systems (PAFS) of the APR+.

  6. Results of a survey on accident and safety analysis codes, benchmarks, verification and validation methods

    International Nuclear Information System (INIS)

    Lee, A.G.; Wilkin, G.B.

    1995-01-01

    This report is a compilation of the information submitted by AECL, CIAE, JAERI, ORNL and Siemens in response to a need identified at the 'Workshop on R and D Needs' at the IGORR-3 meeting. The survey compiled information on the national standards applied to the Safety Quality Assurance (SQA) programs undertaken by the participants. Information was assembled for the computer codes and nuclear data libraries used in accident and safety analyses for research reactors and the methods used to verify and validate the codes and libraries. Although the survey was not comprehensive, it provides a basis for exchanging information of common interest to the research reactor community

  7. Intercomparison and validation of computer codes for thermalhydraulic safety analysis of heavy water reactors

    International Nuclear Information System (INIS)

    2004-08-01

    Activities within the frame of the IAEA's Technical Working Group on Advanced Technologies for HWRs (TWG-HWR) are conducted in a project within the IAEA's subprogramme on nuclear power reactor technology development. The objective of the activities on HWRs is to foster, within the frame of the TWG-HWR, information exchange and co-operative research on technology development for current and future HWRs, with an emphasis on safety, economics and fuel resource sustainability. One of the activities recommended by the TWG-HWR was an international standard problem exercise entitled: Intercomparison and validation of computer codes for thermalhydraulics safety analyses. Intercomparison and validation of computer codes used in different countries for thermalhydraulics safety analyses will enhance the confidence in the predictions made by these codes. However, the intercomparison and validation exercise needs a set of reliable experimental data. The RD-14M Large-Loss Of Coolant Accident (LOCA) test B9401 simulating HWR LOCA behaviour that was conducted by Atomic Energy of Canada Ltd (AECL) was selected for this validation project. This report provides a comparison of the results obtained from six participating countries, utilizing four different computer codes. General conclusions are reached and recommendations made

  8. IAEA programme to support development and validation of advanced design and safety analysis codes

    Energy Technology Data Exchange (ETDEWEB)

    Choi, J., E-mail: J.H.Choi@iaea.org [International Atomic Energy Agency, Vienna (Austria)

    2013-07-01

    The International Atomic Energy Agency (IAEA) has been organized many international collaboration programs to support the development and validation of design and safety analysis computer codes for nuclear power plants. These programs are normally implemented with a frame of Coordinated Research Project (CRP) or International Collaborative Standard Problem (ICSP). This paper introduces CRPs and ICSPs currently being organized or recently completed by IAEA for this purpose. (author)

  9. Results of a survey on accident and safety analysis codes, benchmarks, verification and validation methods

    International Nuclear Information System (INIS)

    Lee, A.G.; Wilkin, G.B.

    1996-03-01

    During the 'Workshop on R and D needs' at the 3rd Meeting of the International Group on Research Reactors (IGORR-III), the participants agreed that it would be useful to compile a survey of the computer codes and nuclear data libraries used in accident and safety analyses for research reactors and the methods various organizations use to verify and validate their codes and libraries. Five organizations, Atomic Energy of Canada Limited (AECL, Canada), China Institute of Atomic Energy (CIAE, People's Republic of China), Japan Atomic Energy Research Institute (JAERI, Japan), Oak Ridge National Laboratories (ORNL, USA), and Siemens (Germany) responded to the survey. The results of the survey are compiled in this report. (author) 36 refs., 3 tabs

  10. Validation study of computer code SPHINCS for sodium fire safety evaluation of fast reactor

    International Nuclear Information System (INIS)

    Yamaguchi, Akira; Tajima, Yuji

    2003-01-01

    A computer code SPHINCS solves coupled phenomena of thermal hydraulics and sodium fire based on a multi-zone model. It deals with an arbitrary number of rooms, each of which is connected mutually by doorways and penetrations. With regard to the combustion phenomena, a flame sheet model and a liquid droplet combustion model are used for pool and spray fires, respectively, with the chemical equilibrium model based on the Gibbs free energy minimization method. The chemical reaction and mass and heat transfer are solved interactively. A specific feature of SPHINCS is detailed representation of thermalhydraulics of a sodium pool and a steel liner, which is placed on the floor to prevent sodium-concrete contact. The authors analyzed a series of pool combustion experiments, in which gas and liner temperatures are measured in detail. It has been found that good agreement is obtained and the SPHINCS code has been validated with regard to pool combustion phenomena. Further research needs are identified for pool spreading modeling considering thermal deformation of steel liner and measurement of pool fluidity property as a mixture of liquid sodium and reaction products. The SPHINCS code is to be used mainly in the safety evaluation of the consequence of a sodium fire accident in a liquid metal cooled fast reactor as well as fire safety analysis in general

  11. Validation of thermalhydraulic codes

    International Nuclear Information System (INIS)

    Wilkie, D.

    1992-01-01

    Thermalhydraulic codes require to be validated against experimental data collected over a wide range of situations if they are to be relied upon. A good example is provided by the nuclear industry where codes are used for safety studies and for determining operating conditions. Errors in the codes could lead to financial penalties, to the incorrect estimation of the consequences of accidents and even to the accidents themselves. Comparison between prediction and experiment is often described qualitatively or in approximate terms, e.g. ''agreement is within 10%''. A quantitative method is preferable, especially when several competing codes are available. The codes can then be ranked in order of merit. Such a method is described. (Author)

  12. Thermal-hydraulic codes validation for safety analysis of NPPs with RBMK

    International Nuclear Information System (INIS)

    Brus, N.A.; Ioussoupov, O.E.

    2000-01-01

    This work is devoted to validation of western thermal-hydraulic codes (RELAP5/MOD3 .2 and ATHLET 1.1 Cycle C) in application to Russian designed light water reactors. Such validation is needed due to features of RBMK reactor design and thermal-hydraulics in comparison with PWR and BWR reactors, for which these codes were developed and validated. These validation studies are concluded with a comparison of calculation results of modeling with the thermal-hydraulics codes with the experiments performed earlier using the thermal-hydraulics test facilities with the experimental data. (authors)

  13. Containment Code Validation Matrix

    International Nuclear Information System (INIS)

    Chin, Yu-Shan; Mathew, P.M.; Glowa, Glenn; Dickson, Ray; Liang, Zhe; Leitch, Brian; Barber, Duncan; Vasic, Aleks; Bentaib, Ahmed; Journeau, Christophe; Malet, Jeanne; Studer, Etienne; Meynet, Nicolas; Piluso, Pascal; Gelain, Thomas; Michielsen, Nathalie; Peillon, Samuel; Porcheron, Emmanuel; Albiol, Thierry; Clement, Bernard; Sonnenkalb, Martin; Klein-Hessling, Walter; Arndt, Siegfried; Weber, Gunter; Yanez, Jorge; Kotchourko, Alexei; Kuznetsov, Mike; Sangiorgi, Marco; Fontanet, Joan; Herranz, Luis; Garcia De La Rua, Carmen; Santiago, Aleza Enciso; Andreani, Michele; Paladino, Domenico; Dreier, Joerg; Lee, Richard; Amri, Abdallah

    2014-01-01

    The Committee on the Safety of Nuclear Installations (CSNI) formed the CCVM (Containment Code Validation Matrix) task group in 2002. The objective of this group was to define a basic set of available experiments for code validation, covering the range of containment (ex-vessel) phenomena expected in the course of light and heavy water reactor design basis accidents and beyond design basis accidents/severe accidents. It was to consider phenomena relevant to pressurised heavy water reactor (PHWR), pressurised water reactor (PWR) and boiling water reactor (BWR) designs of Western origin as well as of Eastern European VVER types. This work would complement the two existing CSNI validation matrices for thermal hydraulic code validation (NEA/CSNI/R(1993)14) and In-vessel core degradation (NEA/CSNI/R(2001)21). The report initially provides a brief overview of the main features of a PWR, BWR, CANDU and VVER reactors. It also provides an overview of the ex-vessel corium retention (core catcher). It then provides a general overview of the accident progression for light water and heavy water reactors. The main focus is to capture most of the phenomena and safety systems employed in these reactor types and to highlight the differences. This CCVM contains a description of 127 phenomena, broken down into 6 categories: - Containment Thermal-hydraulics Phenomena; - Hydrogen Behaviour (Combustion, Mitigation and Generation) Phenomena; - Aerosol and Fission Product Behaviour Phenomena; - Iodine Chemistry Phenomena; - Core Melt Distribution and Behaviour in Containment Phenomena; - Systems Phenomena. A synopsis is provided for each phenomenon, including a description, references for further information, significance for DBA and SA/BDBA and a list of experiments that may be used for code validation. The report identified 213 experiments, broken down into the same six categories (as done for the phenomena). An experiment synopsis is provided for each test. Along with a test description

  14. Validation studies of thermal-hydraulic code for safety analysis of nuclear power plants

    International Nuclear Information System (INIS)

    Haapalehto, T.

    1995-01-01

    The thesis gives an overview of the validation process for thermal-hydraulic system codes and it presents in more detail the assessment and validation of the French code CATHARE for VVER calculations. Three assessment cases are presented: loop seal clearing, core reflooding and flow in a horizontal steam generator. The experience gained during these assessment and validation calculations has been used to analyze the behavior of the horizontal steam generator and the natural circulation in the geometry of the Loviisa nuclear power plant. Large part of the work has been performed in cooperation with the CATHARE-team in Grenoble, France. (41 refs., 11 figs., 8 tabs.)

  15. Validation and verification of the ORNL Monte Carlo codes for nuclear safety analysis

    International Nuclear Information System (INIS)

    Emmett, M.B.

    1993-01-01

    The process of ensuring the quality of computer codes can be very time consuming and expensive. The Oak Ridge National Laboratory (ORNL) Monte Carlo codes all predate the existence of quality assurance (QA) standards and configuration control. The number of person-years and the amount of money spent on code development make it impossible to adhere strictly to all the current requirements. At ORNL, the Nuclear Engineering Applications Section of the Computing Applications Division is responsible for the development, maintenance, and application of the Monte Carlo codes MORSE and KENO. The KENO code is used for doing criticality analyses; the MORSE code, which has two official versions, CGA and SGC, is used for radiation transport analyses. Because KENO and MORSE were very thoroughly checked out over the many years of extensive use both in the United States and in the international community, the existing codes were open-quotes baselined.close quotes This means that the versions existing at the time the original configuration plan is written are considered to be validated and verified code systems based on the established experience with them

  16. Development of Safety Analysis Codes and Experimental Validation for a Very High Temperature Gas-Cooled Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Chang, H. Oh, PhD; Cliff Davis; Richard Moore

    2004-11-01

    The very high temperature gas-cooled reactors (VHTGRs) are those concepts that have average coolant temperatures above 900 degrees C or operational fuel temperatures above 1250 degrees C. These concepts provide the potential for increased energy conversion efficiency and for high-temperature process heat application in addition to power generation and nuclear hydrogen generation. While all the High Temperature Gas Cooled Reactor (HTGR) concepts have sufficiently high temperatures to support process heat applications, such as desalination and cogeneration, the VHTGR's higher temperatures are suitable for particular applications such as thermochemical hydrogen production. However, the high temperature operation can be detrimental to safety following a loss-of-coolant accident (LOCA) initiated by pipe breaks caused by seismic or other events. Following the loss of coolant through the break and coolant depressurization, air from the containment will enter the core by molecular diffusion and ultimately by natural convection, leading to oxidation of the in-core graphite structures and fuel. The oxidation will release heat and accelerate the heatup of the reactor core. Thus, without any effective countermeasures, a pipe break may lead to significant fuel damage and fission product release. The Idaho National Engineering and Environmental Laboratory (INEEL) has investigated this event for the past three years for the HTGR. However, the computer codes used, and in fact none of the world's computer codes, have been sufficiently developed and validated to reliably predict this event. New code development, improvement of the existing codes, and experimental validation are imperative to narrow the uncertaninty in the predictions of this type of accident. The objectives of this Korean/United States collaboration are to develop advanced computational methods for VHTGR safety analysis codes and to validate these computer codes.

  17. Analysis of the impact of correlated benchmark experiments on the validation of codes for criticality safety analysis

    International Nuclear Information System (INIS)

    Bock, M.; Stuke, M.; Behler, M.

    2013-01-01

    The validation of a code for criticality safety analysis requires the recalculation of benchmark experiments. The selected benchmark experiments are chosen such that they have properties similar to the application case that has to be assessed. A common source of benchmark experiments is the 'International Handbook of Evaluated Criticality Safety Benchmark Experiments' (ICSBEP Handbook) compiled by the 'International Criticality Safety Benchmark Evaluation Project' (ICSBEP). In order to take full advantage of the information provided by the individual benchmark descriptions for the application case, the recommended procedure is to perform an uncertainty analysis. The latter is based on the uncertainties of experimental results included in most of the benchmark descriptions. They can be performed by means of the Monte Carlo sampling technique. The consideration of uncertainties is also being introduced in the supplementary sheet of DIN 25478 'Application of computer codes in the assessment of criticality safety'. However, for a correct treatment of uncertainties taking into account the individual uncertainties of the benchmark experiments is insufficient. In addition, correlations between benchmark experiments have to be handled correctly. For example, these correlations can arise due to different cases of a benchmark experiment sharing the same components like fuel pins or fissile solutions. Thus, manufacturing tolerances of these components (e.g. diameter of the fuel pellets) have to be considered in a consistent manner in all cases of the benchmark experiment. At the 2012 meeting of the Expert Group on 'Uncertainty Analysis for Criticality Safety Assessment' (UACSA) of the OECD/NEA a benchmark proposal was outlined that aimed for the determination of the impact on benchmark correlations on the estimation of the computational bias of the neutron multiplication factor (k eff ). The analysis presented here is based on this proposal. (orig.)

  18. Validation Calculations for the Application of MARS Code to the Safety Analysis of Research Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Park, Cheol; Kim, H.; Chae, H. T.; Lim, I. C

    2006-10-15

    In order to investigate the applicability of MARS code to the accident analysis of the HANARO and other RRs, the following test data were simulated. Test data of the HANARO design and operation, Test data of flow instability and void fraction from published documents, IAEA RR transient data in TECDOC-643, Brazilian IEA-R1 experimental data. For the simulation of the HANARO data with finned rod type fuels at low pressure and low temperature conditions, MARS code, developed for the transient analysis of power reactors, was modified. Its prediction capability was assessed against the experimental data for the HANARO. From the assessment results, it can be said that the modified MARS code could be used for analyzing the thermal hydraulic transient of the HANARO. Some other simulations such as flow instability test and reactor transients were also done for the application of MARS code to RRs with plate type fuels. In the simulation for these cases, no modification was made. The results of simulated cases show that the MARS code can be used to the transient analysis of RRs with careful considerations. In particular, it seems that an improvement on a void model may be necessary for dealing with the phenomena in high void conditions.

  19. Validation Calculations for the Application of MARS Code to the Safety Analysis of Research Reactors

    International Nuclear Information System (INIS)

    Park, Cheol; Kim, H.; Chae, H. T.; Lim, I. C.

    2006-10-01

    In order to investigate the applicability of MARS code to the accident analysis of the HANARO and other RRs, the following test data were simulated. Test data of the HANARO design and operation, Test data of flow instability and void fraction from published documents, IAEA RR transient data in TECDOC-643, Brazilian IEA-R1 experimental data. For the simulation of the HANARO data with finned rod type fuels at low pressure and low temperature conditions, MARS code, developed for the transient analysis of power reactors, was modified. Its prediction capability was assessed against the experimental data for the HANARO. From the assessment results, it can be said that the modified MARS code could be used for analyzing the thermal hydraulic transient of the HANARO. Some other simulations such as flow instability test and reactor transients were also done for the application of MARS code to RRs with plate type fuels. In the simulation for these cases, no modification was made. The results of simulated cases show that the MARS code can be used to the transient analysis of RRs with careful considerations. In particular, it seems that an improvement on a void model may be necessary for dealing with the phenomena in high void conditions

  20. Development of safety analysis codes and experimental validation for a very high temperature gas-cooled reactor Final report

    International Nuclear Information System (INIS)

    Chang Oh

    2006-01-01

    The very high-temperature gas-cooled reactor (VHTR) is envisioned as a single- or dual-purpose reactor for electricity and hydrogen generation. The concept has average coolant temperatures above 900 C and operational fuel temperatures above 1250 C. The concept provides the potential for increased energy conversion efficiency and for high-temperature process heat application in addition to power generation. While all the High Temperature Gas Cooled Reactor (HTGR) concepts have sufficiently high temperature to support process heat applications, such as coal gasification, desalination or cogenerative processes, the VHTR's higher temperatures allow broader applications, including thermochemical hydrogen production. However, the very high temperatures of this reactor concept can be detrimental to safety if a loss-of-coolant accident (LOCA) occurs. Following the loss of coolant through the break and coolant depressurization, air will enter the core through the break by molecular diffusion and ultimately by natural convection, leading to oxidation of the in-core graphite structure and fuel. The oxidation will accelerate heatup of the reactor core and the release of toxic gases (CO and CO2) and fission products. Thus, without any effective countermeasures, a pipe break may lead to significant fuel damage and fission product release. Prior to the start of this Korean/United States collaboration, no computer codes were available that had been sufficiently developed and validated to reliably simulate a LOCA in the VHTR. Therefore, we have worked for the past three years on developing and validating advanced computational methods for simulating LOCAs in a VHTR. Research Objectives As described above, a pipe break may lead to significant fuel damage and fission product release in the VHTR. The objectives of this Korean/United States collaboration were to develop and validate advanced computational methods for VHTR safety analysis. The methods that have been developed are now

  1. Development of safety analysis codes and experimental validation for a very high temperature gas-cooled reactor Final report

    Energy Technology Data Exchange (ETDEWEB)

    Chang Oh

    2006-03-01

    The very high-temperature gas-cooled reactor (VHTR) is envisioned as a single- or dual-purpose reactor for electricity and hydrogen generation. The concept has average coolant temperatures above 9000C and operational fuel temperatures above 12500C. The concept provides the potential for increased energy conversion efficiency and for high-temperature process heat application in addition to power generation. While all the High Temperature Gas Cooled Reactor (HTGR) concepts have sufficiently high temperature to support process heat applications, such as coal gasification, desalination or cogenerative processes, the VHTR’s higher temperatures allow broader applications, including thermochemical hydrogen production. However, the very high temperatures of this reactor concept can be detrimental to safety if a loss-of-coolant accident (LOCA) occurs. Following the loss of coolant through the break and coolant depressurization, air will enter the core through the break by molecular diffusion and ultimately by natural convection, leading to oxidation of the in-core graphite structure and fuel. The oxidation will accelerate heatup of the reactor core and the release of toxic gasses (CO and CO2) and fission products. Thus, without any effective countermeasures, a pipe break may lead to significant fuel damage and fission product release. Prior to the start of this Korean/United States collaboration, no computer codes were available that had been sufficiently developed and validated to reliably simulate a LOCA in the VHTR. Therefore, we have worked for the past three years on developing and validating advanced computational methods for simulating LOCAs in a VHTR. Research Objectives As described above, a pipe break may lead to significant fuel damage and fission product release in the VHTR. The objectives of this Korean/United States collaboration were to develop and validate advanced computational methods for VHTR safety analysis. The methods that have been developed are now

  2. Validation and application of the system code TRACE for safety related investigations of innovative nuclear energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Jaeger, Wadim

    2011-12-19

    of these changes and, on the other hand, the success of the new implemented routines and functions. The predictions using the modified TRACE version were close to the experimental data. After validating the modified TRACE version, two design studies related to the Generation IV International Forum (GIF) were investigated. In the first one, a core of a lead-cooled fast reactor (LFR) was analyzed. To include the interaction between the thermal hydraulic and the neutron kinetic due to temperature and density changes, the TRACE code was coupled to the program system ERANOS2.1. The results gained with that coupled system are in accordance with theory and helped to identify sub-assemblies with the highest loads concerning fuel and cladding temperature. The second design which was investigated was the High Performance Light Water Reactor (HPLWR). Since the design of the HPLWR is not finalized, optimization of vital parameters (power, mass flow rate, etc.) are still ongoing. Since most of the parameters are affecting each other, an uncertainty and sensitivity analysis was performed. The uncertainty analysis showed the upper and lower boundaries of selected parameters, which are of importance from the safety point of view (e.g., fuel and cladding temperature, moderator temperature). The sensitivity study identified the most relevant parameters and their influence on the whole system.

  3. Three-dimensional all-speed CFD code for safety analysis of nuclear reactor containment: Status of GASFLOW parallelization, model development, validation and application

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Jianjun, E-mail: jianjun.xiao@kit.edu [Institute of Nuclear and Energy Technologies, Karlsruhe Institute of Technology, P.O. Box 3640, 76021 Karlsruhe (Germany); Travis, John R., E-mail: jack_travis@comcast.com [Engineering and Scientific Software Inc., 3010 Old Pecos Trail, Santa Fe, NM 87505 (United States); Royl, Peter, E-mail: peter.royl@partner.kit.edu [Institute of Nuclear and Energy Technologies, Karlsruhe Institute of Technology, P.O. Box 3640, 76021 Karlsruhe (Germany); Necker, Gottfried, E-mail: gottfried.necker@partner.kit.edu [Institute of Nuclear and Energy Technologies, Karlsruhe Institute of Technology, P.O. Box 3640, 76021 Karlsruhe (Germany); Svishchev, Anatoly, E-mail: anatoly.svishchev@kit.edu [Institute of Nuclear and Energy Technologies, Karlsruhe Institute of Technology, P.O. Box 3640, 76021 Karlsruhe (Germany); Jordan, Thomas, E-mail: thomas.jordan@kit.edu [Institute of Nuclear and Energy Technologies, Karlsruhe Institute of Technology, P.O. Box 3640, 76021 Karlsruhe (Germany)

    2016-05-15

    Highlights: • 3-D scalable semi-implicit pressure-based CFD code for containment safety analysis. • Robust solution algorithm valid for all-speed flows. • Well validated and widely used CFD code for hydrogen safety analysis. • Code applied in various types of nuclear reactor containments. • Parallelization enables high-fidelity models in large scale containment simulations. - Abstract: GASFLOW is a three dimensional semi-implicit all-speed CFD code which can be used to predict fluid dynamics, chemical kinetics, heat and mass transfer, aerosol transportation and other related phenomena involved in postulated accidents in nuclear reactor containments. The main purpose of the paper is to give a brief review on recent GASFLOW code development, validations and applications in the field of nuclear safety. GASFLOW code has been well validated by international experimental benchmarks, and has been widely applied to hydrogen safety analysis in various types of nuclear power plants in European and Asian countries, which have been summarized in this paper. Furthermore, four benchmark tests of a lid-driven cavity flow, low Mach number jet flow, 1-D shock tube and supersonic flow over a forward-facing step are presented in order to demonstrate the accuracy and wide-ranging capability of ICE’d ALE solution algorithm for all-speed flows. GASFLOW has been successfully parallelized using the paradigms of Message Passing Interface (MPI) and domain decomposition. The parallel version, GASFLOW-MPI, adds great value to large scale containment simulations by enabling high-fidelity models, including more geometric details and more complex physics. It will be helpful for the nuclear safety engineers to better understand the hydrogen safety related physical phenomena during the severe accident, to optimize the design of the hydrogen risk mitigation systems and to fulfill the licensing requirements by the nuclear regulatory authorities. GASFLOW-MPI is targeting a high

  4. Computer codes for safety analysis

    International Nuclear Information System (INIS)

    Holland, D.F.

    1986-11-01

    Computer codes for fusion safety analysis have been under development in the United States for about a decade. This paper will discuss five codes that are currently under development by the Fusion Safety Program. The purpose and capability of each code will be presented, a sample given, followed by a discussion of the present status and future development plans

  5. Validation of the reactor dynamics code HEXTRAN

    International Nuclear Information System (INIS)

    Kyrki-Rajamaeki, R.

    1994-05-01

    HEXTRAN is a new three-dimensional, hexagonal reactor dynamics code developed in the Technical Research Centre of Finland (VTT) for VVER type reactors. This report describes the validation work of HEXTRAN. The work has been made with the financing of the Finnish Centre for Radiation and Nuclear Safety (STUK). HEXTRAN is particularly intended for calculation of such accidents, in which radially asymmetric phenomena are included and both good neutron dynamics and two-phase thermal hydraulics are important. HEXTRAN is based on already validated codes. The models of these codes have been shown to function correctly also within the HEXTRAN code. The main new model of HEXTRAN, the spatial neutron kinetics model has been successfully validated against LR-0 test reactor and Loviisa plant measurements. Connected with SMABRE, HEXTRAN can be reliably used for calculation of transients including effects of the whole cooling system of VVERs. Further validation plans are also introduced in the report. (orig.). (23 refs., 16 figs., 2 tabs.)

  6. Flight code validation simulator

    Science.gov (United States)

    Sims, Brent A.

    1996-05-01

    An End-To-End Simulation capability for software development and validation of missile flight software on the actual embedded computer has been developed utilizing a 486 PC, i860 DSP coprocessor, embedded flight computer and custom dual port memory interface hardware. This system allows real-time interrupt driven embedded flight software development and checkout. The flight software runs in a Sandia Digital Airborne Computer and reads and writes actual hardware sensor locations in which Inertial Measurement Unit data resides. The simulator provides six degree of freedom real-time dynamic simulation, accurate real-time discrete sensor data and acts on commands and discretes from the flight computer. This system was utilized in the development and validation of the successful premier flight of the Digital Miniature Attitude Reference System in January of 1995 at the White Sands Missile Range on a two stage attitude controlled sounding rocket.

  7. Verification of reactor safety codes

    International Nuclear Information System (INIS)

    Murley, T.E.

    1978-01-01

    The safety evaluation of nuclear power plants requires the investigation of wide range of potential accidents that could be postulated to occur. Many of these accidents deal with phenomena that are outside the range of normal engineering experience. Because of the expense and difficulty of full scale tests covering the complete range of accident conditions, it is necessary to rely on complex computer codes to assess these accidents. The central role that computer codes play in safety analyses requires that the codes be verified, or tested, by comparing the code predictions with a wide range of experimental data chosen to span the physical phenomena expected under potential accident conditions. This paper discusses the plans of the Nuclear Regulatory Commission for verifying the reactor safety codes being developed by NRC to assess the safety of light water reactors and fast breeder reactors. (author)

  8. Nuclear safety code study

    Energy Technology Data Exchange (ETDEWEB)

    Hu, H.H.; Ford, D.; Le, H.; Park, S.; Cooke, K.L.; Bleakney, T.; Spanier, J.; Wilburn, N.P.; O' Reilly, B.; Carmichael, B.

    1981-01-01

    The objective is to analyze an overpower accident in an LMFBR. A simplified model of the primary coolant loop was developed in order to understand the instabilities encountered with the MELT III and SAS codes. The computer programs were translated for switching to the IBM 4331. Numerical methods were investigated for solving the neutron kinetics equations; the Adams and Gear methods were compared. (DLC)

  9. On-going activities in the European JASMIN project for the development and validation of ASTEC-Na SFR safety simulation code - 15072

    International Nuclear Information System (INIS)

    Girault, N.; Cloarec, L.; Herranz, L.; Bandini, G.; Perez-Martin, S.; Ammirabile, L.

    2015-01-01

    The 4-year JASMIN collaborative project (Joint Advanced Severe accidents Modelling and Integration for Na-cooled fast reactors), started in Dec.2011 in the frame of the 7. Framework Programme of the European Commission. It aims at developing a new European simulation code, ASTEC-Na, dealing with the primary phase of SFR core disruptive accidents. The development of a new code, based on a robust advanced simulation tool and able to encompass the in-vessel and in-containment phenomena occurring during a severe accident is indeed of utmost interest for advanced and innovative future SFRs for which an enhanced safety level will be required. This code, based on the ASTEC European code system developed by IRSN and GRS for severe accidents in water-cooled reactors, is progressively integrating and capitalizing the state-of-the-art knowledge of SFR accidents through physical model improvement or development of new ones. New models are assessed on in-pile (CABRI, SCARABEE etc...) and out-of pile experiments conducted during the 70's-80's and code-o-code benchmarking with current accident simulation tools for SFRs is also conducted. During the 2 and a half first years of the project, model specifications and developments were conducted and the validation test matrix was built. The first version of ASTEC-Na available in early 2014 already includes a thermal-hydraulics module able to simulate single and two-phase sodium flow conditions, a zero point neutronic model with simple definition of channel and axial dependences of reactivity feedbacks and models derived from SCANAIR IRSN code for simulating fuel pin thermo-mechanical behaviour and fission gas release/retention. Meanwhile, models have been developed in the source term area for in-containment particle generation and particle chemical transformation, but their implementation is still to be done. As a first validation step, the ASTEC-Na calculations were satisfactorily compared to thermal-hydraulics experimental

  10. On the safety and performance demonstration tests of Prototype Gen-IV Sodium-Cooled Fast Reactor and validation and verification of computational codes

    International Nuclear Information System (INIS)

    Kim, Jong Bum; Jeong, Ji Young; Lee, Tae Ho; Kim, Sung Kyun; Euh, Dong Jin; Joo, Hyung Kook

    2016-01-01

    The design of Prototype Gen-IV Sodium-Cooled Fast Reactor (PGSFR) has been developed and the validation and verification (V and V) activities to demonstrate the system performance and safety are in progress. In this paper, the current status of test activities is described briefly and significant results are discussed. The large-scale sodium thermal-hydraulic test program, Sodium Test Loop for Safety Simulation and Assessment-1 (STELLA-1), produced satisfactory results, which were used for the computer codes V and V, and the performance test results of the model pump in sodium showed good agreement with those in water. The second phase of the STELLA program with the integral effect tests facility, STELLA-2, is in the detailed design stage of the design process. The sodium thermal-hydraulic experiment loop for finned-tube sodium-to-air heat exchanger performance test, the intermediate heat exchanger test facility, and the test facility for the reactor flow distribution are underway. Flow characteristics test in subchannels of a wire-wrapped rod bundle has been carried out for safety analysis in the core and the dynamic characteristic test of upper internal structure has been performed for the seismic analysis model for the PGSFR. The performance tests for control rod assemblies (CRAs) have been conducted for control rod drive mechanism driving parts and drop tests of the CRA under scram condition were performed. Finally, three types of inspection sensors under development for the safe operation of the PGSFR were explained with significant results

  11. On the safety and performance demonstration tests of Prototype Gen-IV Sodium-Cooled Fast Reactor and validation and verification of computational codes

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Bum; Jeong, Ji Young; Lee, Tae Ho; Kim, Sung Kyun; Euh, Dong Jin; Joo, Hyung Kook [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    The design of Prototype Gen-IV Sodium-Cooled Fast Reactor (PGSFR) has been developed and the validation and verification (V and V) activities to demonstrate the system performance and safety are in progress. In this paper, the current status of test activities is described briefly and significant results are discussed. The large-scale sodium thermal-hydraulic test program, Sodium Test Loop for Safety Simulation and Assessment-1 (STELLA-1), produced satisfactory results, which were used for the computer codes V and V, and the performance test results of the model pump in sodium showed good agreement with those in water. The second phase of the STELLA program with the integral effect tests facility, STELLA-2, is in the detailed design stage of the design process. The sodium thermal-hydraulic experiment loop for finned-tube sodium-to-air heat exchanger performance test, the intermediate heat exchanger test facility, and the test facility for the reactor flow distribution are underway. Flow characteristics test in subchannels of a wire-wrapped rod bundle has been carried out for safety analysis in the core and the dynamic characteristic test of upper internal structure has been performed for the seismic analysis model for the PGSFR. The performance tests for control rod assemblies (CRAs) have been conducted for control rod drive mechanism driving parts and drop tests of the CRA under scram condition were performed. Finally, three types of inspection sensors under development for the safe operation of the PGSFR were explained with significant results.

  12. Nuclear Energy Advanced Modeling and Simulation Waste Integrated Performance and Safety Codes (NEAMS Waste IPSC) verification and validation plan. version 1.

    Energy Technology Data Exchange (ETDEWEB)

    Bartlett, Roscoe Ainsworth; Arguello, Jose Guadalupe, Jr.; Urbina, Angel; Bouchard, Julie F.; Edwards, Harold Carter; Freeze, Geoffrey A.; Knupp, Patrick Michael; Wang, Yifeng; Schultz, Peter Andrew; Howard, Robert (Oak Ridge National Laboratory, Oak Ridge, TN); McCornack, Marjorie Turner

    2011-01-01

    The objective of the U.S. Department of Energy Office of Nuclear Energy Advanced Modeling and Simulation Waste Integrated Performance and Safety Codes (NEAMS Waste IPSC) is to provide an integrated suite of computational modeling and simulation (M&S) capabilities to quantitatively assess the long-term performance of waste forms in the engineered and geologic environments of a radioactive-waste storage facility or disposal repository. To meet this objective, NEAMS Waste IPSC M&S capabilities will be applied to challenging spatial domains, temporal domains, multiphysics couplings, and multiscale couplings. A strategic verification and validation (V&V) goal is to establish evidence-based metrics for the level of confidence in M&S codes and capabilities. Because it is economically impractical to apply the maximum V&V rigor to each and every M&S capability, M&S capabilities will be ranked for their impact on the performance assessments of various components of the repository systems. Those M&S capabilities with greater impact will require a greater level of confidence and a correspondingly greater investment in V&V. This report includes five major components: (1) a background summary of the NEAMS Waste IPSC to emphasize M&S challenges; (2) the conceptual foundation for verification, validation, and confidence assessment of NEAMS Waste IPSC M&S capabilities; (3) specifications for the planned verification, validation, and confidence-assessment practices; (4) specifications for the planned evidence information management system; and (5) a path forward for the incremental implementation of this V&V plan.

  13. On the Safety and Performance Demonstration Tests of Prototype Gen-IV Sodium-Cooled Fast Reactor and Validation and Verification of Computational Codes

    Directory of Open Access Journals (Sweden)

    Jong-Bum Kim

    2016-10-01

    Full Text Available The design of Prototype Gen-IV Sodium-Cooled Fast Reactor (PGSFR has been developed and the validation and verification (V&V activities to demonstrate the system performance and safety are in progress. In this paper, the current status of test activities is described briefly and significant results are discussed. The large-scale sodium thermal-hydraulic test program, Sodium Test Loop for Safety Simulation and Assessment-1 (STELLA-1, produced satisfactory results, which were used for the computer codes V&V, and the performance test results of the model pump in sodium showed good agreement with those in water. The second phase of the STELLA program with the integral effect tests facility, STELLA-2, is in the detailed design stage of the design process. The sodium thermal-hydraulic experiment loop for finned-tube sodium-to-air heat exchanger performance test, the intermediate heat exchanger test facility, and the test facility for the reactor flow distribution are underway. Flow characteristics test in subchannels of a wire-wrapped rod bundle has been carried out for safety analysis in the core and the dynamic characteristic test of upper internal structure has been performed for the seismic analysis model for the PGSFR. The performance tests for control rod assemblies (CRAs have been conducted for control rod drive mechanism driving parts and drop tests of the CRA under scram condition were performed. Finally, three types of inspection sensors under development for the safe operation of the PGSFR were explained with significant results.

  14. SCALE criticality safety verification and validation package

    International Nuclear Information System (INIS)

    Bowman, S.M.; Emmett, M.B.; Jordan, W.C.

    1998-01-01

    Verification and validation (V and V) are essential elements of software quality assurance (QA) for computer codes that are used for performing scientific calculations. V and V provides a means to ensure the reliability and accuracy of such software. As part of the SCALE QA and V and V plans, a general V and V package for the SCALE criticality safety codes has been assembled, tested and documented. The SCALE criticality safety V and V package is being made available to SCALE users through the Radiation Safety Information Computational Center (RSICC) to assist them in performing adequate V and V for their SCALE applications

  15. Development and validation of sodium fire codes

    International Nuclear Information System (INIS)

    Morii, Tadashi; Himeno Yoshiaki; Miyake, Osamu

    1989-01-01

    Development, verification, and validation of the spray fire code, SPRAY-3M, the pool fire codes, SOFIRE-M2 and SPM, the aerosol behavior code, ABC-INTG, and the simultaneous spray and pool fires code, ASSCOPS, are presented. In addition, the state-of-the-art of development of the multi-dimensional natural convection code, SOLFAS, for the analysis of heat-mass transfer during a fire, is presented. (author)

  16. Gap Conductance model Validation in the TASS/SMR-S code using MARS code

    International Nuclear Information System (INIS)

    Ahn, Sang Jun; Yang, Soo Hyung; Chung, Young Jong; Lee, Won Jae

    2010-01-01

    Korea Atomic Energy Research Institute (KAERI) has been developing the TASS/SMR-S (Transient and Setpoint Simulation/Small and Medium Reactor) code, which is a thermal hydraulic code for the safety analysis of the advanced integral reactor. An appropriate work to validate the applicability of the thermal hydraulic models within the code should be demanded. Among the models, the gap conductance model which is describes the thermal gap conductivity between fuel and cladding was validated through the comparison with MARS code. The validation of the gap conductance model was performed by evaluating the variation of the gap temperature and gap width as the changed with the power fraction. In this paper, a brief description of the gap conductance model in the TASS/SMR-S code is presented. In addition, calculated results to validate the gap conductance model are demonstrated by comparing with the results of the MARS code with the test case

  17. Code conversion for system design and safety analysis of NSSS

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hae Cho; Kim, Young Tae; Choi, Young Gil; Kim, Hee Kyung [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1996-01-01

    This report describes overall project works related to conversion, installation and validation of computer codes which are used in NSSS design and safety analysis of nuclear power plants. Domain/os computer codes for system safety analysis are installed and validated on Apollo DN10000, and then Apollo version are converted and installed again on HP9000/700 series with appropriate validation. Also, COOLII and COAST which are cyber version computer codes are converted into versions of Apollo DN10000 and HP9000/700, and installed with validation. This report details whole processes of work involved in the computer code conversion and installation, as well as software verification and validation results which are attached to this report. 12 refs., 8 figs. (author)

  18. Validation of fuel performance codes at the NRI Rez plc for Temelin and Dukovany NPPs fuel safety evaluations and operation support

    International Nuclear Information System (INIS)

    Valach, M.; Hejna, J.; Zymak, J.

    2003-05-01

    The report summarises the first phase of the FUMEX II related work performed in the period September 2002 - May 2003. An inventory of the PIN and FRAS codes family used and developed during previous years was made in light of their applicability (validity) in the domain of high burn-up and FUMEX II Project Experimental database. KOLA data were chosen as appropriate for the first step of both codes fixing (both tuned for VVER fuel originally). The modern requirements, expressed by adaptation of the UO 2 conductivity degradation from OECD HRP, RIM and FGR (athermal) modelling implementation into the PIN code and a diffusion FGR model development planned for embedding, into this code allow us to reasonably shadow or keep tight contact with top quality models as TRANSURANUS, COPERNIC, CYRANO, FEMAXI, FRAPCON3 or ENIGMA. Testing and validation runs with prepared input KOLA deck were made. FUMEX II exercise propose LOCA and RIA like transients, so we started development of those two codes coupling - denominated as PIN2FRAS code. Principles of the interface were tested, benchmarking on tentative RIA pulses on highly burned KOLA fuel are presented as the first achievement from our work. (author)

  19. Nuclear data to support computer code validation

    International Nuclear Information System (INIS)

    Fisher, S.E.; Broadhead, B.L.; DeHart, M.D.; Primm, R.T. III

    1997-04-01

    The rate of plutonium disposition will be a key parameter in determining the degree of success of the Fissile Materials Disposition Program. Estimates of the disposition rate are dependent on neutronics calculations. To ensure that these calculations are accurate, the codes and data should be validated against applicable experimental measurements. Further, before mixed-oxide (MOX) fuel can be fabricated and loaded into a reactor, the fuel vendors, fabricators, fuel transporters, reactor owners and operators, regulatory authorities, and the Department of Energy (DOE) must accept the validity of design calculations. This report presents sources of neutronics measurements that have potential application for validating reactor physics (predicting the power distribution in the reactor core), predicting the spent fuel isotopic content, predicting the decay heat generation rate, certifying criticality safety of fuel cycle facilities, and ensuring adequate radiation protection at the fuel cycle facilities and the reactor. The U.S. in-reactor experience with MOX fuel is first presented, followed by information related to other aspects of the MOX fuel performance information that is valuable to this program, but the data base remains largely proprietary. Thus, this information is not reported here. It is expected that the selected consortium will make the necessary arrangements to procure or have access to the requisite information

  20. Light-water reactor safety analysis codes

    International Nuclear Information System (INIS)

    Jackson, J.F.; Ransom, V.H.; Ybarrondo, L.J.; Liles, D.R.

    1980-01-01

    A brief review of the evolution of light-water reactor safety analysis codes is presented. Included is a summary comparison of the technical capabilities of major system codes. Three recent codes are described in more detail to serve as examples of currently used techniques. Example comparisons between calculated results using these codes and experimental data are given. Finally, a brief evaluation of current code capability and future development trends is presented

  1. Status of SPACE Safety Analysis Code Development

    International Nuclear Information System (INIS)

    Lee, Dong Hyuk; Yang, Chang Keun; Kim, Se Yun; Ha, Sang Jun

    2009-01-01

    In 2006, the Korean the Korean nuclear industry started developing a thermal-hydraulic analysis code for safety analysis of PWR(Pressurized Water Reactor). The new code is named as SPACE(Safety and Performance Analysis Code for Nuclear Power Plant). The SPACE code can solve two-fluid, three-field governing equations in one dimensional or three dimensional geometry. The SPACE code has many component models required for modeling a PWR, such as reactor coolant pump, safety injection tank, etc. The programming language used in the new code is C++, for new generation of engineers who are more comfortable with C/C++ than old FORTRAN language. This paper describes general characteristics of SPACE code and current status of SPACE code development

  2. Cable SGEMP Code Validation Study

    Energy Technology Data Exchange (ETDEWEB)

    Ballard, William Parker [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Center for CA Weapons Systems Engineering

    2013-05-01

    This report compared data taken on the Modular Bremsstrahlung Simulator using copper jacketed (cujac) cables with calculations using the RHSD-RA Cable SGEMP analysis tool. The tool relies on CEPXS/ONBFP to perform radiation transport in a series of 1D slices through the cable, and then uses a Green function technique to evaluate the expected current drive on the center conductor. The data were obtained in 2003 as part of a Cabana verification and validation experiment using 1-D geometries, but were not evaluated until now. The agreement between data and model is not adequate unless gaps between the dielectric and outer conductor (ground) are assumed, and these gaps are large compared with what is believed to be in the actual cable.

  3. Computational Fluid Dynamics (CFD) for Nuclear Reactor Safety Applications - Workshop Proceedings, CFD4NRS-3 - Experimental Validation and Application of CFD and CMFD Codes to Nuclear Reactor Safety Issues

    International Nuclear Information System (INIS)

    2012-01-01

    related to nuclear reactor safety issues. The conference consisted of 14 technical sessions. Among the topics included were containment, advanced reactors, multiphase flows, flow in a rod bundle, fire analysis, flows in dry casks, thermal analysis, mixing flows and pressurized thermal shock (PTS). About 1/3 of the papers were concerned with two-phase flow issues and the rest were devoted to single-phase CFD validation. South Korea is a candidate to host a follow-up meeting scheduled in 2012, organized by KAERI. KAERI also volunteered to sponsor and organize the second OECD/NEA CFD benchmark exercise. In the closure meeting after the panel session discussion, the representative from the Paul Scherrer Institut (PSI) proposed to host a future workshop scheduled for 2014, and to organize and sponsor the third OECD/NEA benchmark exercise based on a stratification experiment in the PANDA facility at PSI. The great majority of participants were interested in attending a follow-up workshop within two years. Comments were made during the panel session on the content of CFD4NRS-3. Two of the comments are that experiments can provide insight into the physics, and that CFD is now an accepted analysis tool, though it is very important to follow BPGs. There was a consensus on the need to maintain the high quality of the papers. The promotion of international benchmarking exercises for CFD was strongly encouraged. Another comment suggested that such workshops should be a forum to discuss novel approaches, but that one must also keep in mind that the end users are people from the nuclear safety community. The CFD4NRS, XCFD4NRS and CFD4NRS-3 workshops have proved to be very valuable means to assess the status of CFD code capabilities and validation, to exchange experiences in CFD code applications, and to monitor future progress

  4. Validations and applications of the FEAST code

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Z.; Tayal, M.; Lau, J.H.; Evinou, D. [Atomic Energy of Canada Limited, Mississauga, Ontario (Canada); Jun, J.S. [Korea Atomic Energy Research Inst. (Korea, Republic of)

    1999-07-01

    The FEAST (Finite Element Analysis for STresses) code is part of a suite of computer codes that are used to assess the structural integrity of CANDu fuel elements and bundles. A detailed validation of the FEAST code was recently performed. The FEAST calculations are in good agreement with a variety of analytical solutions (18 cases) for stresses, strains and displacements. This consistency shows that the FEAST code correctly incorporates the fundamentals of stress analysis. Further, the calculations of the FEAST code match the variations in axial and hoop strain profiles, measured by strain gauges near the sheath-endcap weld during an out-reactor compression test. The code calculations are also consistent with photoelastic measurements in simulated endcaps. (author)

  5. Validations and applications of the FEAST code

    International Nuclear Information System (INIS)

    Xu, Z.; Tayal, M.; Lau, J.H.; Evinou, D.; Jun, J.S.

    1999-01-01

    The FEAST (Finite Element Analysis for STresses) code is part of a suite of computer codes that are used to assess the structural integrity of CANDu fuel elements and bundles. A detailed validation of the FEAST code was recently performed. The FEAST calculations are in good agreement with a variety of analytical solutions (18 cases) for stresses, strains and displacements. This consistency shows that the FEAST code correctly incorporates the fundamentals of stress analysis. Further, the calculations of the FEAST code match the variations in axial and hoop strain profiles, measured by strain gauges near the sheath-endcap weld during an out-reactor compression test. The code calculations are also consistent with photoelastic measurements in simulated endcaps. (author)

  6. Validation of the VTT's reactor physics code system

    International Nuclear Information System (INIS)

    Tanskanen, A.

    1998-01-01

    At VTT Energy several international reactor physics codes and nuclear data libraries are used in a variety of applications. The codes and libraries are under constant development and every now and then new updated versions are released, which are taken in use as soon as they have been validated at VTT Energy. The primary aim of the validation is to ensure that the code works properly, and that it can be used correctly. Moreover, the applicability of the codes and libraries are studied in order to establish their advantages and weak points. The capability of generating program-specific nuclear data for different reactor physics codes starting from the same evaluated data is sometimes of great benefit. VTT Energy has acquired a nuclear data processing system based on the NJOY-94.105 and TRANSX-2.15 processing codes. The validity of the processing system has been demonstrated by generating pointwise (MCNP) and groupwise (ANISN) temperature-dependent cross section sets for the benchmark calculations of the Doppler coefficient of reactivity. At VTT Energy the KENO-VI three-dimensional Monte Carlo code is used in criticality safety analyses. The KENO-VI code and the 44GROUPNDF5 data library have been validated at VTT Energy against the ZR-6 and LR-0 critical experiments. Burnup Credit refers to the reduction in reactivity of burned nuclear fuel due to the change in composition during irradiation. VTT Energy has participated in the calculational VVER-440 burnup credit benchmark in order to validate criticality safety calculation tools. (orig.)

  7. Validation of the TAC/BLOOST code (Contract research)

    International Nuclear Information System (INIS)

    Takamatsu, Kuniyoshi; Nakagawa, Shigeaki

    2005-06-01

    Safety demonstration tests using the High Temperature engineering Test Reactor (HTTR) are in progress to verify the inherent safety features for High Temperature Gas-cooled Reactors (HTGRs). The coolant flow reduction test by tripping gas circulators is one of the safety demonstration tests. The reactor power safely brings to a stable level without a reactor scram and the temperature transient of the reactor-core is very slow. The TAC/BLOOST code was developed to analyze reactor and temperature transient during the coolant flow reduction test taking account of reactor dynamics. This paper describes the validation result of the TAC/BLOOST code with the measured values of gas circulators tripping tests at 30% (9 MW). It was confirmed that the TAC/BLOOST code was able to analyze the reactor transient during the test. (author)

  8. Validation of comprehensive space radiation transport code

    International Nuclear Information System (INIS)

    Shinn, J.L.; Simonsen, L.C.; Cucinotta, F.A.

    1998-01-01

    The HZETRN code has been developed over the past decade to evaluate the local radiation fields within sensitive materials on spacecraft in the space environment. Most of the more important nuclear and atomic processes are now modeled and evaluation within a complex spacecraft geometry with differing material components, including transition effects across boundaries of dissimilar materials, are included. The atomic/nuclear database and transport procedures have received limited validation in laboratory testing with high energy ion beams. The codes have been applied in design of the SAGE-III instrument resulting in material changes to control injurious neutron production, in the study of the Space Shuttle single event upsets, and in validation with space measurements (particle telescopes, tissue equivalent proportional counters, CR-39) on Shuttle and Mir. The present paper reviews the code development and presents recent results in laboratory and space flight validation

  9. Code of safety for nuclear merchant ships

    International Nuclear Information System (INIS)

    1982-01-01

    The Code is in chapters, entitled: general (including general safety principles and principles of risk acceptance); design criteria and conditions; ship design, construction and equipment; nuclear steam supply system; machinery and electrical installations; radiation safety (including radiological protection design; protection of persons; dosimetry; radioactive waste management); operation (including emergency operation procedures); surveys. Appendices cover: sinking velocity calculations; seaway loads depending on service periods; safety assessment; limiting dose-equivalent rates for different areas and spaces; quality assurance programme; application of single failure criterion. Initial application of the Code is restricted to conventional types of ships propelled by nuclear propulsion plants with pressurized light water type reactors. (U.K.)

  10. Integrated Validation System for a Thermal-hydraulic System Code, TASS/SMR-S

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hee-Kyung; Kim, Hyungjun; Kim, Soo Hyoung; Hwang, Young-Dong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Hyeon-Soo [Chungnam National University, Daejeon (Korea, Republic of)

    2015-10-15

    Development including enhancement and modification of thermal-hydraulic system computer code is indispensable to a new reactor, SMART. Usually, a thermal-hydraulic system code validation is achieved by a comparison with the results of corresponding physical effect tests. In the reactor safety field, a similar concept, referred to as separate effect tests has been used for a long time. But there are so many test data for comparison because a lot of separate effect tests and integral effect tests are required for a code validation. It is not easy to a code developer to validate a computer code whenever a code modification is occurred. IVS produces graphs which shown the comparison the code calculation results with the corresponding test results automatically. IVS was developed for a validation of TASS/SMR-S code. The code validation could be achieved by a comparison code calculation results with corresponding test results. This comparison was represented as a graph for convenience. IVS is useful before release a new code version. The code developer can validate code result easily using IVS. Even during code development, IVS could be used for validation of code modification. The code developer could gain a confidence about his code modification easily and fast and could be free from tedious and long validation work. The popular software introduced in IVS supplies better usability and portability.

  11. Results from the First Validation Phase of CAP code

    International Nuclear Information System (INIS)

    Choo, Yeon Joon; Hong, Soon Joon; Hwang, Su Hyun; Kim, Min Ki; Lee, Byung Chul; Ha, Sang Jun; Choi, Hoon

    2010-01-01

    The second stage of Safety Analysis Code Development for Nuclear Power Plants was lunched on Apirl, 2010 and is scheduled to be through 2012, of which the scope of work shall cover from code validation to licensing preparation. As a part of this project, CAP(Containment Analysis Package) will follow the same procedures. CAP's validation works are organized hieratically into four validation steps using; 1) Fundamental phenomena. 2) Principal phenomena (mixing and transport) and components in containment. 3) Demonstration test by small, middle, large facilities and International Standard Problems. 4) Comparison with other containment codes such as GOTHIC or COMTEMPT. In addition, collecting the experimental data related to containment phenomena and then constructing the database is one of the major works during the second stage as a part of this project. From the validation process of fundamental phenomenon, it could be expected that the current capability and the future improvements of CAP code will be revealed. For this purpose, simple but significant problems, which have the exact analytical solution, were selected and calculated for validation of fundamental phenomena. In this paper, some results of validation problems for the selected fundamental phenomena will be summarized and discussed briefly

  12. 45 CFR 162.1011 - Valid code sets.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Valid code sets. 162.1011 Section 162.1011 Public... ADMINISTRATIVE REQUIREMENTS Code Sets § 162.1011 Valid code sets. Each code set is valid within the dates specified by the organization responsible for maintaining that code set. ...

  13. Validation of the reactor dynamics code TRAB

    International Nuclear Information System (INIS)

    Raety, H.; Kyrki-Rajamaeki, R.; Rajamaeki, M.

    1991-05-01

    The one-dimensional reactor dynamics code TRAB (Transient Analysis code for BWRs) developed at VTT was originally designed for BWR analyses, but it can in its present version be used for various modelling purposes. The core model of TRAB can be used separately for LWR calculations. For PWR modelling the core model of TRAB has been coupled to circuit model SMABRE to form the SMATRA code. The versatile modelling capabilities of TRAB have been utilized also in analyses of e.g. the heating reactor SECURE and the RBMK-type reactor (Chernobyl). The report summarizes the extensive validation of TRAB. TRAB has been validated with benchmark problems, comparative calculations against independent analyses, analyses of start-up experiments of nuclear power plants and real plant transients. Comparative RBMES type reactor calculations have been made against Soviet simulations and the initial power excursion of the Chernobyl reactor accident has also been calculated with TRAB

  14. Contributions to the validation of the ASTEC V1 code

    International Nuclear Information System (INIS)

    Constantin, Marin; Rizoiu, Andrei; Turcu, Ilie

    2004-01-01

    In the frame of PHEBEN2 project (Validation of the severe accidents codes for applications to nuclear power plants, based on the PHEBUS FP experiments), a project developed within the EU research Frame Program 5 (FP5), the INR-Pitesti's team has received the task of determining the ASTEC code sensitivity. The PHEBEN2 project has been initiated in 1998 and gathered 13 partners from 6 EU member states. To the project 4 partners from 3 candidate states (Hungary, Bulgaria and Romania) joined later. The works were contracted with the European Commission (under FIKS-CT1999-00009 contract) that supports financially the research effort up to about 50%. According to the contract provisions, INR's team participated in developing the Working Package 1 (WP1) which refers to validation of the integral computation codes that use the PHOEBUS experimental data and the Working Package 3 (WP3) referring to the evaluation of the codes to be applied in nuclear power plants for risk evaluation, nuclear safety margin evaluation and determination/evaluation of the measures to be adopted in case of severe accident. The present work continues the efforts to validate preliminarily the ASTEC code. Focused are the the stand-alone sensitivity analyses applied to two most important modules of the code, namely DIVA and SOPHAEROS

  15. Validation of OPERA3D PCMI Analysis Code

    Energy Technology Data Exchange (ETDEWEB)

    Jeun, Ji Hoon; Choi, Jae Myung; Yoo, Jong Sung [KEPCO Nuclear Fuel Co., Daejeon (Korea, Republic of); Cheng, G.; Sim, K. S.; Chassie, Girma [Candu Energy INC.,Ontario (Canada)

    2013-10-15

    This report will describe introduction of validation of OPERA3D code, and validation results that are directly related with PCMI phenomena. OPERA3D was developed for the PCMI analysis and validated using the in-pile measurement data. Fuel centerline temperature and clad strain calculation results shows close expectations with measurement data. Moreover, 3D FEM fuel model of OPERA3D shows slight hour glassing behavior of fuel pellet in contact case. Further optimization will be conducted for future application of OPERA3D code. Nuclear power plant consists of many complicated systems, and one of the important objects of all the systems is maintaining nuclear fuel integrity. However, it is inevitable to experience PCMI (Pellet Cladding Mechanical Interaction) phenomena at current operating reactors and next generation reactors for advanced safety and economics as well. To evaluate PCMI behavior, many studies are on-going to develop 3-dimensional fuel performance evaluation codes. Moreover, these codes are essential to set the safety limits for the best estimated PCMI phenomena aimed for high burnup fuel.

  16. Experimental validation of the HARMONIE code

    International Nuclear Information System (INIS)

    Bernard, A.; Dorsselaere, J.P. van

    1984-01-01

    An experimental program of deformation, in air, of different groups of subassemblies (7 to 41 subassemblies), was performed on a scale 1 mock-up in the SPX1 geometry, in order to achieve a first experimental validation of the code HARMONIE. The agreement between tests and calculations was suitable, qualitatively for all the groups and quantitatively for regular groups of 19 subassemblies at most. The differences come mainly from friction between pads, and secondly from the foot gaps. (author)

  17. The WINCON programme - validation of fast reactor primary containment codes

    International Nuclear Information System (INIS)

    Sidoli, J.E.A.; Kendall, K.C.

    1988-01-01

    In the United Kingdom safety studies for the Commercial Demonstration Fast Reactor (CDFR) include an assessment of the capability of the primary containment in providing an adequate containment for defence against the hazards resulting from a hypothetical Whole Core Accident (WCA). The assessment is based on calculational estimates using computer codes supported by measured evidence from small-scale experiments. The hydrodynamic containment code SEURBNUK-EURDYN is capable of representing a prescribed energy release, the sodium coolant and cover gas, and the main containment and safety related internal structures. Containment loadings estimated using SEURBNUK-EURDYN are used in the structural dynamic code EURDYN-03 for the prediction of the containment response. The experiments serve two purposes, they demonstrate the response of the CDFR containment to accident loadings and provide data for the validation of the codes. This paper summarises the recently completed WINfrith CONtainment (WINCON) experiments that studied the response of specific features of current CDFR design options to WCA loadings. The codes have been applied to some of the experiments and a satisfactory prediction of the global response of the model containment is obtained. This provides confidence in the use of the codes in reactor assessments. (author)

  18. Safety evaluations required in the safety regulations for Monju and the validity confirmation of safety evaluation methods

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-15

    The purposes of this study are to perform the safety evaluations of the fast breeder reactor 'Monju' and to confirm the validity of the safety evaluation methods. In JFY 2012, the following results were obtained. As for the development of safety evaluation methods needed in the safety examination achieved for the reactor establishment permission, development of the analysis codes, such as a core damage analysis code, were carried out according to the plan. As for the development of the safety evaluation method needed for the risk informed safety regulation, the quantification technique of the event tree using the Continuous Markov chain Monte Carlo method (CMMC method) were studied. (author)

  19. Certification plan for safety and PRA codes

    International Nuclear Information System (INIS)

    Toffer, H.; Crowe, R.D.; Ades, M.J.

    1990-05-01

    A certification plan for computer codes used in Safety Analyses and Probabilistic Risk Assessment (PRA) for the operation of the Savannah River Site (SRS) reactors has been prepared. An action matrix, checklists, and a time schedule have been included in the plan. These items identify what is required to achieve certification of the codes. A list of Safety Analysis and Probabilistic Risk Assessment (SA ampersand PRA) computer codes covered by the certification plan has been assembled. A description of each of the codes was provided in Reference 4. The action matrix for the configuration control plan identifies code specific requirements that need to be met to achieve the certification plan's objectives. The checklist covers the specific procedures that are required to support the configuration control effort and supplement the software life cycle procedures based on QAP 20-1 (Reference 7). A qualification checklist for users establishes the minimum prerequisites and training for achieving levels of proficiency in using configuration controlled codes for critical parameter calculations

  20. Verification and Validation of Heat Transfer Model of AGREE Code

    Energy Technology Data Exchange (ETDEWEB)

    Tak, N. I. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Seker, V.; Drzewiecki, T. J.; Downar, T. J. [Department of Nuclear Engineering and Radiological Sciences, Univ. of Michigan, Michigan (United States); Kelly, J. M. [US Nuclear Regulatory Commission, Washington (United States)

    2013-05-15

    The AGREE code was originally developed as a multi physics simulation code to perform design and safety analysis of Pebble Bed Reactors (PBR). Currently, additional capability for the analysis of Prismatic Modular Reactor (PMR) core is in progress. Newly implemented fluid model for a PMR core is based on a subchannel approach which has been widely used in the analyses of light water reactor (LWR) cores. A hexagonal fuel (or graphite block) is discretized into triangular prism nodes having effective conductivities. Then, a meso-scale heat transfer model is applied to the unit cell geometry of a prismatic fuel block. Both unit cell geometries of multi-hole and pin-in-hole types of prismatic fuel blocks are considered in AGREE. The main objective of this work is to verify and validate the heat transfer model newly implemented for a PMR core in the AGREE code. The measured data in the HENDEL experiment were used for the validation of the heat transfer model for a pin-in-hole fuel block. However, the HENDEL tests were limited to only steady-state conditions of pin-in-hole fuel blocks. There exist no available experimental data regarding a heat transfer in multi-hole fuel blocks. Therefore, numerical benchmarks using conceptual problems are considered to verify the heat transfer model of AGREE for multi-hole fuel blocks as well as transient conditions. The CORONA and GAMMA+ codes were used to compare the numerical results. In this work, the verification and validation study were performed for the heat transfer model of the AGREE code using the HENDEL experiment and the numerical benchmarks of selected conceptual problems. The results of the present work show that the heat transfer model of AGREE is accurate and reliable for prismatic fuel blocks. Further validation of AGREE is in progress for a whole reactor problem using the HTTR safety test data such as control rod withdrawal tests and loss-of-forced convection tests.

  1. Validation of Magnetic Reconstruction Codes for Real-Time Applications

    International Nuclear Information System (INIS)

    Mazon, D.; Murari, A.; Boulbe, C.; Faugeras, B.; Blum, J.; Svensson, J.; Quilichini, T.; Gelfusa, M.

    2010-01-01

    The real-time reconstruction of the plasma magnetic equilibrium in a tokamak is a key point to access high-performance regimes. Indeed, the shape of the plasma current density profile is a direct output of the reconstruction and has a leading effect for reaching a steady-state high-performance regime of operation. The challenge is thus to develop real-time methods and algorithms that reconstruct the magnetic equilibrium from the perspective of using these outputs for feedback control purposes. In this paper the validation of the JET real-time equilibrium reconstruction codes using both a Bayesian approach and a full equilibrium solver named Equinox will be detailed, the comparison being performed with the off-line equilibrium code EFIT (equilibrium fitting) or the real-time boundary reconstruction code XLOC (X-point local expansion). In this way a significant database, a methodology, and a strategy for the validation are presented. The validation of the results has been performed using a validated database of 130 JET discharges with a large variety of magnetic configurations. Internal measurements like polarimetry and motional Stark effect have been also used for the Equinox validation including some magnetohydrodynamic signatures for the assessment of the reconstructed safety profile and current density. (authors)

  2. Measurement of reactivity coefficients for code validation

    International Nuclear Information System (INIS)

    Nuding, Matthias; Loetsch, Thomas

    2005-01-01

    In the year 2003 measurements in the cold reactor state have been performed at the NPP KKI 2 in order to validate the codes that are used for reactor core calculations and especially for the proof of the shutdown margin that is produced by calculations only. For full power states code verification is quite easy because the calculations can be compared with different measured values, e.g. with the activation values determined by the aeroball system. For cold reactor states, however the data base is smaller, especially for reactor cores that are quite 'inhomogeneous' and have rather high Pu-fiss-and 235 U-contents. At the same time the cold reactor state is important regarding the shutdown margin. For these reasons the measurements mentioned above have been performed in order to check the accuracy of the codes that are used by the operator and by our organization for many years. Basically, boron concentrations and control rod worths for different configurations have been measured. The results of the calculation show a very good agreement with the measured values. Therefore, it can be stated that the operator's as well as our code system is suitable for routine use, e.g. during licensing procedures (Authors)

  3. Validation of containment thermal hydraulic computer codes for VVER reactor

    Energy Technology Data Exchange (ETDEWEB)

    Jiri Macek; Lubomir Denk [Nuclear Research Institute Rez plc Thermal-Hydraulic Analyses Department CZ 250 68 Husinec-Rez (Czech Republic)

    2005-07-01

    Full text of publication follows: The Czech Republic operates 4 VVER-440 units, two VVER-1000 units are being finalized (one of them is undergoing commissioning). Thermal-hydraulics Department of the Nuclear Research Institute Rez performs accident analyses for these plants using a number of computer codes. To model the primary and secondary circuits behaviour the system codes ATHLET, CATHARE, RELAP, TRAC are applied. Containment and pressure-suppression system are modelled with COCOSYS and MELCOR codes, the reactor power calculations (point and space-neutron kinetics) are made with DYN3D, NESTLE and CDF codes (FLUENT, TRIO) are used for some specific problems.An integral part of the current Czech project 'New Energy Sources' is selection of a new nuclear source. Within this and the preceding projects financed by the Czech Ministry of Industry and Trade and the EU PHARE, the Department carries and has carried out the systematic validation of thermal-hydraulic and reactor physics computer codes applying data obtained on several experimental facilities as well as the real operational data. One of the important components of the VVER 440/213 NPP is its containment with pressure suppression system (bubble condenser). For safety analyses of this system, computer codes of the type MELCOR and COCOSYS are used in the Czech Republic. These codes were developed for containments of classic PWRs or BWRs. In order to apply these codes for VVER 440 systems, their validation on experimental facilities must be performed.The paper provides concise information on these activities of the NRI and its Thermal-hydraulics Department. The containment system of the VVER 440/213, its functions and approaches to solution of its safety is described with definition of acceptance criteria. A detailed example of the containment code validation on EREC Test facility (LOCA and MSLB) and the consequent utilisation of the results for a real NPP purposes is included. An approach to

  4. Pulse coded safety logic for PFBR

    International Nuclear Information System (INIS)

    Anwer, Md. Najam; Satheesh, N.; Nagaraj, C.P.; Krishnakumar, B.

    2002-01-01

    Full text: Reactor safety logic is designed to initiate safety action against design basis events. The reactor is shutdown by de-energizing electromagnets and dropping the absorber rods under gravity. In prototype fast breeder reactor (PFBR), shutdown is affected by two independent shutdown systems, viz., control and safety rod drive mechanism (CSRDM) and diverse safety rod drive mechanism (DSRDM). Two separate safety logics are proposed for CSRDM and DSRDM, i.e. solid state logic with on-line fine impulse test (FIT) for CSRDM and pulse coded safety logic (PCSL) for DSRDM. The PCSL primarily utilizes the fact that the vast majority of faults in the logic circuitry result in static conditions at the output. It is arranged such that the presence of pulses are required to hold the shutdown actuators and any DC logic state, either logic 0 or logic 1 releases them. It is a dynamic, self-testing logic and used in a number of reactors. This paper describes the principle of operation of PCSL, its advantages, the concept of guard line logic (GLL), detection of stuck at 0 and stuck at 1 faults, fail safe and diversity features. The implementation of PCSL using Altera Max+Plus II software for PFBR trip signals and the results of simulation are discussed. This paper also describes a test jig using 80186 based system for testing PCSL for various input parameter's combinations and monitoring the outputs

  5. Code on the safety of nuclear power plants: Siting

    International Nuclear Information System (INIS)

    1988-01-01

    This Code provides criteria and procedures that are recommended for safety in nuclear power plant siting. It forms part of the Agency's programme for establishing Codes and Safety Guides relating to land based stationary thermal neutron power plants

  6. 38 CFR 61.20 - Life Safety Code capital grants.

    Science.gov (United States)

    2010-07-01

    ... (CONTINUED) VA HOMELESS PROVIDERS GRANT AND PER DIEM PROGRAM § 61.20 Life Safety Code capital grants. (a) This section sets forth provisions for obtaining a Life Safety Code capital grant under 38 U.S.C. 2012... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Life Safety Code capital...

  7. MOSEG code for safety oriented maintenance management Safety of management of maintenance oriented by MOSEG code

    International Nuclear Information System (INIS)

    Torres Valle, Antonio

    2005-01-01

    Full text: One of the main reasons that makes maintenance contribute highly when facing safety problems and facilities availability is the lack of maintenance management systems to solve these fields in a balanced way. Their main setbacks are shown in this paper. It briefly describes the development of an integrating algorithm for a safety and availability-oriented maintenance management by virtue of the MOSEG Win 1.0 code. (author)

  8. IAEA code and safety guides on quality assurance

    International Nuclear Information System (INIS)

    Raisic, N.

    1980-01-01

    In the framework of its programme in safety standards development, the IAEA has recently published a Code of Practice on Quality Assurance for Safety in Nuclear Power Plants. The Code establishes minimum requirements for quality assurance which Member States should use in the context of their own nuclear safety requirements. A series of 10 Safety Guides which describe acceptable methods of implementing the requirements of specific sections of the Code are in preparation. (orig.)

  9. Gamma streaming experiments for validation of Monte Carlo code

    International Nuclear Information System (INIS)

    Thilagam, L.; Mohapatra, D.K.; Subbaiah, K.V.; Iliyas Lone, M.; Balasubramaniyan, V.

    2012-01-01

    In-homogeneities in shield structures lead to considerable amount of leakage radiation (streaming) increasing the radiation levels in accessible areas. Development works on experimental as well as computational methods for quantifying this streaming radiation are still continuing. Monte Carlo based radiation transport code, MCNP is usually a tool for modeling and analyzing such problems involving complex geometries. In order to validate this computational method for streaming analysis, it is necessary to carry out some experimental measurements simulating these inhomogeneities like ducts and voids present in the bulk shields for typical cases. The data thus generated will be analysed by simulating the experimental set up employing MCNP code and optimized input parameters for the code in finding solutions for similar radiation streaming problems will be formulated. Comparison of experimental data obtained from radiation streaming experiments through ducts will give a set of thumb rules and analytical fits for total radiation dose rates within and outside the duct. The present study highlights the validation of MCNP code through the gamma streaming experiments carried out with the ducts of various shapes and dimensions. Over all, the present study throws light on suitability of MCNP code for the analysis of gamma radiation streaming problems for all duct configurations considered. In the present study, only dose rate comparisons have been made. Studies on spectral comparison of streaming radiation are in process. Also, it is planned to repeat the experiments with various shield materials. Since the penetrations and ducts through bulk shields are unavoidable in an operating nuclear facility the results on this kind of radiation streaming simulations and experiments will be very useful in the shield structure optimization without compromising the radiation safety

  10. Criticality safety validation of MCNP5 using continuous energy libraries

    International Nuclear Information System (INIS)

    Salome, Jean A.D.; Pereira, Claubia; Assuncao, Jonathan B.A.; Veloso, Maria Auxiliadora F.; Costa, Antonella L.; Silva, Clarysson A.M. da

    2013-01-01

    The study of subcritical systems is very important in the design, installation and operation of various devices, mainly nuclear reactors and power plants. The information generated by these systems guide the decisions to be taken in the executive project, the economic viability and the safety measures to be employed in a nuclear facility. Simulating some experiments from the International Handbook of Evaluated Criticality Safety Benchmark Experiments, the code MCNP5 was validated to nuclear criticality analysis. Its continuous libraries were used. The average values and standard deviation (SD) were evaluated. The results obtained with the code are very similar to the values obtained by the benchmark experiments. (author)

  11. Validation and applicability of the 3D core kinetics and thermal hydraulics coupled code SPARKLE

    International Nuclear Information System (INIS)

    Miyata, Manabu; Maruyama, Manabu; Ogawa, Junto; Otake, Yukihiko; Miyake, Shuhei; Tabuse, Shigehiko; Tanaka, Hirohisa

    2009-01-01

    The SPARKLE code is a coupled code system based on three individual codes whose physical models have already been verified and validated. Mitsubishi Heavy Industries (MHI) confirmed the coupling calculation, including data transfer and the total reactor coolant system (RCS) behavior of the SPARKLE code. The confirmation uses the OECD/NEA MSLB benchmark problem, which is based on Three Mile Island Unit 1 (TMI-1) nuclear power plant data. This benchmark problem has been used to verify coupled codes developed and used by many organizations. Objectives of the benchmark program are as follows. Phase 1 is to compare the results of the system transient code using point kinetics. Phase 2 is to compare the results of the coupled three-dimensional (3D) core kinetics code and 3D core thermal-hydraulics (T/H) code, and Phase 3 is to compare the results of the combined coupled system transient code, 3D core kinetics code, and 3D core T/H code as a total validation of the coupled calculation. The calculation results of the SPARKLE code indicate good agreement with other benchmark participants' results. Therefore, the SPARKLE code is validated through these benchmark problems. In anticipation of applying the SPARKLE code to licensing analyses, MHI and Japanese PWR utilities have established a safety analysis method regarding the calculation conditions such as power distributions, reactivity coefficients, and event-specific features. (author)

  12. SAFETY IN THE DESIGN OF SCIENCE LABORATORIES AND BUILDING CODES.

    Science.gov (United States)

    HOROWITZ, HAROLD

    THE DESIGN OF COLLEGE AND UNIVERSITY BUILDINGS USED FOR SCIENTIFIC RESEARCH AND EDUCATION IS DISCUSSED IN TERMS OF LABORATORY SAFETY AND BUILDING CODES AND REGULATIONS. MAJOR TOPIC AREAS ARE--(1) SAFETY RELATED DESIGN FEATURES OF SCIENCE LABORATORIES, (2) LABORATORY SAFETY AND BUILDING CODES, AND (3) EVIDENCE OF UNSAFE DESIGN. EXAMPLES EMPHASIZE…

  13. Validation of physics and thermalhydraulic computer codes for advanced Candu reactor applications

    International Nuclear Information System (INIS)

    Wren, D.J.; Popov, N.; Snell, V.G.

    2004-01-01

    Atomic Energy of Canada Ltd. (AECL) is developing an Advanced Candu Reactor (ACR) that is an evolutionary advancement of the currently operating Candu 6 reactors. The ACR is being designed to produce electrical power for a capital cost and at a unit-energy cost significantly less than that of the current reactor designs. The ACR retains the modular Candu concept of horizontal fuel channels surrounded by a heavy water moderator. However, ACR uses slightly enriched uranium fuel compared to the natural uranium used in Candu 6. This achieves the twin goals of improved economics (via large reductions in the heavy water moderator volume and replacement of the heavy water coolant with light water coolant) and improved safety. AECL has developed and implemented a software quality assurance program to ensure that its analytical, scientific and design computer codes meet the required standards for software used in safety analyses. Since the basic design of the ACR is equivalent to that of the Candu 6, most of the key phenomena associated with the safety analyses of ACR are common, and the Candu industry standard tool-set of safety analysis codes can be applied to the analysis of the ACR. A systematic assessment of computer code applicability addressing the unique features of the ACR design was performed covering the important aspects of the computer code structure, models, constitutive correlations, and validation database. Arising from this assessment, limited additional requirements for code modifications and extensions to the validation databases have been identified. This paper provides an outline of the AECL software quality assurance program process for the validation of computer codes used to perform physics and thermal-hydraulics safety analyses of the ACR. It describes the additional validation work that has been identified for these codes and the planned, and ongoing, experimental programs to extend the code validation as required to address specific ACR design

  14. The predictive validity of safety climate.

    Science.gov (United States)

    Johnson, Stephen E

    2007-01-01

    Safety professionals have increasingly turned their attention to social science for insight into the causation of industrial accidents. One social construct, safety climate, has been examined by several researchers [Cooper, M. D., & Phillips, R. A. (2004). Exploratory analysis of the safety climate and safety behavior relationship. Journal of Safety Research, 35(5), 497-512; Gillen, M., Baltz, D., Gassel, M., Kirsch, L., & Vacarro, D. (2002). Perceived safety climate, job Demands, and coworker support among union and nonunion injured construction workers. Journal of Safety Research, 33(1), 33-51; Neal, A., & Griffin, M. A. (2002). Safety climate and safety behaviour. Australian Journal of Management, 27, 66-76; Zohar, D. (2000). A group-level model of safety climate: Testing the effect of group climate on microaccidents in manufacturing jobs. Journal of Applied Psychology, 85(4), 587-596; Zohar, D., & Luria, G. (2005). A multilevel model of safety climate: Cross-level relationships between organization and group-level climates. Journal of Applied Psychology, 90(4), 616-628] who have documented its importance as a factor explaining the variation of safety-related outcomes (e.g., behavior, accidents). Researchers have developed instruments for measuring safety climate and have established some degree of psychometric reliability and validity. The problem, however, is that predictive validity has not been firmly established, which reduces the credibility of safety climate as a meaningful social construct. The research described in this article addresses this problem and provides additional support for safety climate as a viable construct and as a predictive indicator of safety-related outcomes. This study used 292 employees at three locations of a heavy manufacturing organization to complete the 16 item Zohar Safety Climate Questionnaire (ZSCQ) [Zohar, D., & Luria, G. (2005). A multilevel model of safety climate: Cross-level relationships between organization and group

  15. Spent reactor fuel benchmark composition data for code validation

    International Nuclear Information System (INIS)

    Bierman, S.R.

    1991-09-01

    To establish criticality safety margins utilizing burnup credit in the storage and transport of spent reactor fuels requires a knowledge of the uncertainty in the calculated fuel composition used in making the reactivity assessment. To provide data for validating such calculated burnup fuel compositions, radiochemical assays are being obtained as part of the United States Department of Energy From-Reactor Cask Development Program. Destructive assay data are being obtained from representative reactor fuels having experienced irradiation exposures up to about 55 GWD/MTM. Assay results and associated operating histories on the initial three samples analyzed in this effort are presented. The three samples were taken from different axial regions of the same fuel rod and represent radiation exposures of about 27, 37, and 44 GWD/MTM. The data are presented in a benchmark type format to facilitate identification/referencing and computer code input

  16. Development of an Auto-Validation Program for MARS Code Assessments

    International Nuclear Information System (INIS)

    Lee, Young Jin; Chung, Bub Dong

    2006-01-01

    MARS (Multi-dimensional Analysis of Reactor Safety) code is a best-estimate thermal hydraulic system analysis code developed at KAERI. It is important for a thermal hydraulic computer code to be assessed against theoretical and experimental data to verify and validate the performance and the integrity of the structure, models and correlations of the code. The code assessment efforts for complex thermal hydraulics code such as MARS code can be tedious, time-consuming and require large amount of human intervention in data transfer to see the results in graphic forms. Code developers produce many versions of a code during development and each version need to be verified for integrity. Thus, for MARS code developers, it is desirable to have an automatic way of carrying out the code assessment calculations. In the present work, an Auto-Validation program that carries out the code assessment efforts has been developed. The program uses the user supplied configuration file (with '.vv' extension) which contain commands to read input file, to execute the user selected MARS program, and to generate result graphs. The program can be useful if a same set of code assessments is repeated with different versions of the code. The program is written with the Delphi program language. The program runs under the Microsoft Windows environment

  17. A fuel performance code TRUST VIc and its validation

    Energy Technology Data Exchange (ETDEWEB)

    Ishida, M; Kogai, T [Nippon Nuclear Fuel Development Co. Ltd., Oarai, Ibaraki (Japan)

    1997-08-01

    This paper describes a fuel performance code TRUST V1c developed to analyze thermal and mechanical behavior of LWR fuel rod. Submodels in the code include FP gas models depicting gaseous swelling, gas release from pellet and axial gas mixing. The code has FEM-based structure to handle interaction between thermal and mechanical submodels brought by the gas models. The code is validated against irradiation data of fuel centerline temperature, FGR, pellet porosity and cladding deformation. (author). 9 refs, 8 figs.

  18. A fuel performance code TRUST VIc and its validation

    International Nuclear Information System (INIS)

    Ishida, M.; Kogai, T.

    1997-01-01

    This paper describes a fuel performance code TRUST V1c developed to analyze thermal and mechanical behavior of LWR fuel rod. Submodels in the code include FP gas models depicting gaseous swelling, gas release from pellet and axial gas mixing. The code has FEM-based structure to handle interaction between thermal and mechanical submodels brought by the gas models. The code is validated against irradiation data of fuel centerline temperature, FGR, pellet porosity and cladding deformation. (author). 9 refs, 8 figs

  19. LIMBO computer code for analyzing coolant-voiding dynamics in LMFBR safety tests

    International Nuclear Information System (INIS)

    Bordner, G.L.

    1979-10-01

    The LIMBO (liquid metal boiling) code for the analysis of two-phase flow phenomena in an LMFBR reactor coolant channel is presented. The code uses a nonequilibrium, annular, two-phase flow model, which allows for slip between the phases. Furthermore, the model is intended to be valid for both quasi-steady boiling and rapid coolant voiding of the channel. The code was developed primarily for the prediction of, and the posttest analysis of, coolant-voiding behavior in the SLSF P-series in-pile safety test experiments. The program was conceived to be simple, efficient, and easy to use. It is particularly suited for parametric studies requiring many computer runs and for the evaluation of the effects of model or correlation changes that require modification of the computer program. The LIMBO code, of course, lacks the sophistication and model detail of the reactor safety codes, such as SAS, and is therefore intended to compliment these safety codes

  20. Code on the safety of nuclear power plants: Governmental organization

    International Nuclear Information System (INIS)

    1988-01-01

    This Code recommends requirements for a regulatory body responsible for regulating the siting, design, construction, commissioning, operation and decommissioning of nuclear power plants for safety. It forms part of the Agency's programme for establishing Codes and Safety Guides relating to land based stationary thermal neutron power plants

  1. INL Experimental Program Roadmap for Thermal Hydraulic Code Validation

    Energy Technology Data Exchange (ETDEWEB)

    Glenn McCreery; Hugh McIlroy

    2007-09-01

    Advanced computer modeling and simulation tools and protocols will be heavily relied on for a wide variety of system studies, engineering design activities, and other aspects of the Next Generation Nuclear Power (NGNP) Very High Temperature Reactor (VHTR), the DOE Global Nuclear Energy Partnership (GNEP), and light-water reactors. The goal is for all modeling and simulation tools to be demonstrated accurate and reliable through a formal Verification and Validation (V&V) process, especially where such tools are to be used to establish safety margins and support regulatory compliance, or to design a system in a manner that reduces the role of expensive mockups and prototypes. Recent literature identifies specific experimental principles that must be followed in order to insure that experimental data meet the standards required for a “benchmark” database. Even for well conducted experiments, missing experimental details, such as geometrical definition, data reduction procedures, and manufacturing tolerances have led to poor Benchmark calculations. The INL has a long and deep history of research in thermal hydraulics, especially in the 1960s through 1980s when many programs such as LOFT and Semiscle were devoted to light-water reactor safety research, the EBRII fast reactor was in operation, and a strong geothermal energy program was established. The past can serve as a partial guide for reinvigorating thermal hydraulic research at the laboratory. However, new research programs need to fully incorporate modern experimental methods such as measurement techniques using the latest instrumentation, computerized data reduction, and scaling methodology. The path forward for establishing experimental research for code model validation will require benchmark experiments conducted in suitable facilities located at the INL. This document describes thermal hydraulic facility requirements and candidate buildings and presents examples of suitable validation experiments related

  2. Validity of your safety awareness training

    CERN Multimedia

    DG Unit

    2010-01-01

    AIS is setting up an automatic e-mail reminder system for safety training. You are invited to forward this message to everyone concerned. Reminder: Please check the validity of your Safety courses Since April 2009 the compulsory basic Safety awareness courses (levels 1, 2 and 3) have been accessible on a "self-service" basis on the web (see CERN Bulletin). Participants are required to pass a test at the end of each course. The test is valid for 3 years so courses must be repeated on a regular basis. A system of automatic e-mail reminders already exists for level 4 courses on SIR and will be extended to the other levels shortly. The number of levels you are required to complete depends on your professional category. Activity Personnel concerned Level 1 Level 2 Level 3 Level 4     Basic safety Basic Safety ...

  3. Challenges on innovations of newly-developed safety analysis codes

    International Nuclear Information System (INIS)

    Yang, Yanhua; Zhang, Hao

    2016-01-01

    With the development of safety analysis method, the safety analysis codes meet more challenges. Three challenges are presented in this paper, which are mathematic model, code design and user interface. Combined with the self-reliance safety analysis code named COSINE, the ways of meeting these requirements are suggested, that is to develop multi-phases, multi-fields and multi-dimension models, to adopt object-oriented code design ideal and to improve the way of modeling, calculation control and data post-processing in the user interface.

  4. Challenges on innovations of newly-developed safety analysis codes

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Yanhua [Shanghai Jiao Tong Univ. (China). School of Nuclear Science and Engineering; Zhang, Hao [State Nuclear Power Software Development Center, Beijing (China). Beijing Future Science and Technology City

    2016-05-15

    With the development of safety analysis method, the safety analysis codes meet more challenges. Three challenges are presented in this paper, which are mathematic model, code design and user interface. Combined with the self-reliance safety analysis code named COSINE, the ways of meeting these requirements are suggested, that is to develop multi-phases, multi-fields and multi-dimension models, to adopt object-oriented code design ideal and to improve the way of modeling, calculation control and data post-processing in the user interface.

  5. Reactor safety computer code development at INEL

    International Nuclear Information System (INIS)

    Johnsen, G.W.

    1985-01-01

    This report provides a brief overview of the computer code development programs being conducted at EG and G Idaho, Inc. on behalf of US Nuclear Regulatory Commission and the Department of Energy, Idaho Operations Office. Included are descriptions of the codes being developed, their development status as of the date of this report, and resident code development expertise

  6. Code on the safety of civilian nuclear fuel cycle installations

    International Nuclear Information System (INIS)

    1996-01-01

    The 'Code' was promulgated by the National Nuclear Safety Administration (NSSA) on June 17, 1993, which is applicable to civilian nuclear fuel fabrication, processing, storage and reprocessing installations, not including the safety requirements for the use of nuclear fuel in reactors. The contents of the 'Code' involve siting, design, construction, commissioning, operation and decommissioning of fuel cycle installation. The NNSA shall be responsible for the interpretation of this 'Code'

  7. Development and validation of sodium fire analysis code ASSCOPS

    International Nuclear Information System (INIS)

    Ohno, Shuji

    2001-01-01

    A version 2.1 of the ASSCOPS sodium fire analysis code was developed to evaluate the thermal consequences of a sodium leak and consequent fire in LMFBRs. This report describes the computational models and the validation studies using the code. The ASSCOPS calculates sodium droplet and pool fire, and consequential heat/mass transfer behavior. Analyses of sodium pool or spray fire experiments confirmed that this code and parameters used in the validation studies gave valid results on the thermal consequences of sodium leaks and fires. (author)

  8. Fusion safety codes International modeling with MELCOR and ATHENA- INTRA

    CERN Document Server

    Marshall, T; Topilski, L; Merrill, B

    2002-01-01

    For a number of years, the world fusion safety community has been involved in benchmarking their safety analyses codes against experiment data to support regulatory approval of a next step fusion device. This paper discusses the benchmarking of two prominent fusion safety thermal-hydraulic computer codes. The MELCOR code was developed in the US for fission severe accident safety analyses and has been modified for fusion safety analyses. The ATHENA code is a multifluid version of the US-developed RELAP5 code that is also widely used for fusion safety analyses. The ENEA Fusion Division uses ATHENA in conjunction with the INTRA code for its safety analyses. The INTRA code was developed in Germany and predicts containment building pressures, temperatures and fluid flow. ENEA employs the French-developed ISAS system to couple ATHENA and INTRA. This paper provides a brief introduction of the MELCOR and ATHENA-INTRA codes and presents their modeling results for the following breaches of a water cooling line into the...

  9. European Validation of the Integral Code ASTEC (EVITA)

    International Nuclear Information System (INIS)

    Allelein, H.-J.; Neu, K.; Dorsselaere, J.P. Van

    2005-01-01

    The main objective of the European Validation of the Integral Code ASTEC (EVITA) project is to distribute the severe accident integral code ASTEC to European partners in order to apply the validation strategy issued from the VASA project (4th EC FWP). Partners evaluate the code capability through validation on reference experiments and plant applications accounting for severe accident management measures, and compare results with reference codes. The basis version V0 of ASTEC (Accident Source Term Evaluation Code)-commonly developed and basically validated by GRS and IRSN-was made available in late 2000 for the EVITA partners on their individual platforms. Users' training was performed by IRSN and GRS. The code portability on different computers was checked to be correct. A 'hot line' assistance was installed continuously available for EVITA code users. The actual version V1 has been released to the EVITA partners end of June 2002. It allows to simulate the front-end phase by two new modules:- for reactor coolant system 2-phase simplified thermal hydraulics (5-equation approach) during both front-end and core degradation phases; - for core degradation, based on structure and main models of ICARE2 (IRSN) reference mechanistic code for core degradation and on other simplified models. Next priorities are clearly identified: code consolidation in order to increase the robustness, extension of all plant applications beyond the vessel lower head failure and coupling with fission product modules, and continuous improvements of users' tools. As EVITA has very successfully made the first step into the intention to provide end-users (like utilities, vendors and licensing authorities) with a well validated European integral code for the simulation of severe accidents in NPPs, the EVITA partners strongly recommend to continue validation, benchmarking and application of ASTEC. This work will continue in Severe Accident Research Network (SARNET) in the 6th Framework Programme

  10. Technique for unit testing of safety software verification and validation

    International Nuclear Information System (INIS)

    Li Duo; Zhang Liangju; Feng Junting

    2008-01-01

    The key issue arising from digitalization of the reactor protection system for nuclear power plant is how to carry out verification and validation (V and V), to demonstrate and confirm the software that performs reactor safety functions is safe and reliable. One of the most important processes for software V and V is unit testing, which verifies and validates the software coding based on concept design for consistency, correctness and completeness during software development. The paper shows a preliminary study on the technique for unit testing of safety software V and V, focusing on such aspects as how to confirm test completeness, how to establish test platform, how to develop test cases and how to carry out unit testing. The technique discussed here was successfully used in the work of unit testing on safety software of a digital reactor protection system. (authors)

  11. Code on the safety of nuclear power plants: Design

    International Nuclear Information System (INIS)

    1988-01-01

    This Code is a compilation of nuclear safety principles aimed at defining the essential requirements necessary to ensure nuclear safety. These requirements are applicable to structures, systems and components, and procedures important to safety in nuclear power plants embodying thermal neutron reactors, with emphasis on what safety requirements shall be met rather than on specifying how these requirements can be met. It forms part of the Agency's programme for establishing Codes and Safety Guides relating to land based stationary thermal neutron power plants. The document should be used by organizations designing, manufacturing, constructing and operating nuclear power plants as well as by regulatory bodies

  12. Evaluation and validation of criticality codes for fuel dissolver calculations

    International Nuclear Information System (INIS)

    Santamarina, A.; Smith, H.J.; Whitesides, G.E.

    1991-01-01

    During the past ten years an OECD/NEA Criticality Working Group has examined the validity of criticality safety computational methods. International calculation tools which were shown to be valid in systems for which experimental data existed were demonstrated to be inadequate when extrapolated to fuel dissolver media. A theoretical study of the main physical parameters involved in fuel dissolution calculations was performed, i.e. range of moderation, variation of pellet size and the fuel double heterogeneity effect. The APOLLO/P IC method developed to treat this latter effect permits us to supply the actual reactivity variation with pellet dissolution and to propose international reference values. The disagreement among contributors' calculations was analyzed through a neutron balance breakdown, based on three-group microscopic reaction rates. The results pointed out that fast and resonance nuclear data in criticality codes are not sufficiently reliable. Moreover the neutron balance analysis emphasized the inadequacy of the standard self-shielding formalism to account for 238 U resonance mutual self-shielding in the pellet-fissile liquor interaction. The benchmark exercise has resolved a potentially dangerous inadequacy in dissolver calculations. (author)

  13. Simulation codes and the impact of validation/uncertainty requirements

    International Nuclear Information System (INIS)

    Sills, H.E.

    1995-01-01

    Several of the OECD/CSNI members have adapted a proposed methodology for code validation and uncertainty assessment. Although the validation process adapted by members has a high degree of commonality, the uncertainty assessment processes selected are more variable, ranaing from subjective to formal. This paper describes the validation and uncertainty assessment process, the sources of uncertainty, methods of reducing uncertainty, and methods of assessing uncertainty.Examples are presented from the Ontario Hydro application of the validation methodology and uncertainty assessment to the system thermal hydraulics discipline and the TUF (1) system thermal hydraulics code. (author)

  14. Uniform emergency codes: will they improve safety?

    Science.gov (United States)

    2005-01-01

    There are pros and cons to uniform code systems, according to emergency medicine experts. Uniformity can be a benefit when ED nurses and other staff work at several facilities. It's critical that your staff understand not only what the codes stand for, but what they must do when codes are called. If your state institutes a new system, be sure to hold regular drills to familiarize your ED staff.

  15. Verification and validation process for the safety software in KNICS

    International Nuclear Information System (INIS)

    Kwon, Kee-Choon; Lee, Jang-Soo; Kim, Jang-Yeol

    2004-01-01

    This paper describes the Verification and Validation (V and V ) process for safety software of Programmable Logic Controller (PLC), Digital Reactor Protection System (DRPS), and Engineered Safety Feature-Component Control System (ESF-CCS) that are being developed in Korea Nuclear Instrumentation and Control System (KNICS) projects. Specifically, it presents DRPS V and V experience according to the software development life cycle. The main activities of DRPS V and V process are preparation of software planning documentation, verification of Software Requirement Specification (SRS), Software Design Specification (SDS) and codes, and testing of the integrated software and the integrated system. In addition, they include software safety analysis and software configuration management. SRS V and V of DRPS are technical evaluation, licensing suitability evaluation, inspection and traceability analysis, formal verification, preparing integrated system test plan, software safety analysis, and software configuration management. Also, SDS V and V of RPS are technical evaluation, licensing suitability evaluation, inspection and traceability analysis, formal verification, preparing integrated software test plan, software safety analysis, and software configuration management. The code V and V of DRPS are traceability analysis, source code inspection, test case and test procedure generation, software safety analysis, and software configuration management. Testing is the major V and V activity of software integration and system integration phase. Software safety analysis at SRS phase uses Hazard Operability (HAZOP) method, at SDS phase it uses HAZOP and Fault Tree Analysis (FTA), and at implementation phase it uses FTA. Finally, software configuration management is performed using Nu-SCM (Nuclear Software Configuration Management) tool developed by KNICS project. Through these activities, we believe we can achieve the functionality, performance, reliability and safety that are V

  16. Computer code validation by high temperature chemistry

    International Nuclear Information System (INIS)

    Alexander, C.A.; Ogden, J.S.

    1988-01-01

    At least five of the computer codes utilized in analysis of severe fuel damage-type events are directly dependent upon or can be verified by high temperature chemistry. These codes are ORIGEN, CORSOR, CORCON, VICTORIA, and VANESA. With the exemption of CORCON and VANESA, it is necessary that verification experiments be performed on real irradiated fuel. For ORIGEN, the familiar knudsen effusion cell is the best choice and a small piece of known mass and known burn-up is selected and volatilized completely into the mass spectrometer. The mass spectrometer is used in the integral mode to integrate the entire signal from preselected radionuclides, and from this integrated signal the total mass of the respective nuclides can be determined. For CORSOR and VICTORIA, experiments with flowing high pressure hydrogen/steam must flow over the irradiated fuel and then enter the mass spectrometer. For these experiments, a high pressure-high temperature molecular beam inlet must be employed. Finally, in support of VANESA-CORCON, the very highest temperature and molten fuels must be contained and analyzed. Results from all types of experiments will be discussed and their applicability to present and future code development will also be covered

  17. Evaluation and validation of criticality codes for fuel dissolver calculations

    International Nuclear Information System (INIS)

    Santamarina, A.; Smith, H.J.; Whitesides, G.E.

    1991-01-01

    During the past ten years an OECD/NEA Criticality Working Group has examined the validity of criticality safety computational methods. International calculation tools which were shown to be valid in systems for which experimental data existed were demonstrated to be inadequate when extrapolated to fuel dissolver media. The spread of the results in the international calculation amounted to ± 12,000 pcm in the realistic fuel dissolver exercise n degrees 19 proposed by BNFL, and to ± 25,000 pcm in the benchmark n degrees 20 in which fissile material in solid form is surrounded by fissile material in solution. A theoretical study of the main physical parameters involved in fuel dissolution calculations was performed, i.e. range of moderation, variation of pellet size and the fuel double heterogeneity effect. The APOLLO/P IC method developed to treat latter effect, permits us to supply the actual reactivity variation with pellet dissolution and to propose international reference values. The disagreement among contributors' calculations was analyzed through a neutron balance breakdown, based on three-group microscopic reaction rates solicited from the participants. The results pointed out that fast and resonance nuclear data in criticality codes are not sufficiently reliable. Moreover the neutron balance analysis emphasized the inadequacy of the standard self-shielding formalism (NITAWL in the international SCALE package) to account for 238 U resonance mutual self-shielding in the pellet-fissile liquor interaction. Improvements in the up-dated 1990 contributions, as do recent complementary reference calculations (MCNP, VIM, ultrafine slowing-down CGM calculation), confirm the need to use rigorous self-shielding methods in criticality design-oriented codes. 6 refs., 11 figs., 3 tabs

  18. Verification and validation of XSDRNPM code for tank waste calculations

    International Nuclear Information System (INIS)

    ROGERS, C.A.

    1999-01-01

    This validation study demonstrates that the XSDRNPM computer code accurately calculates the infinite neutron multiplication for water-moderated systems of low enriched uranium, plutonium, and iron. Calculations are made on a 200 MHz Brvo MS 5200M personal

  19. Validation uncertainty of MATRA code for subchannel void distributions

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Dae-Hyun; Kim, S. J.; Kwon, H.; Seo, K. W. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    To extend code capability to the whole core subchannel analysis, pre-conditioned Krylov matrix solvers such as BiCGSTAB and GMRES are implemented in MATRA code as well as parallel computing algorithms using MPI and OPENMP. It is coded by fortran 90, and has some user friendly features such as graphic user interface. MATRA code was approved by Korean regulation body for design calculation of integral-type PWR named SMART. The major role subchannel code is to evaluate core thermal margin through the hot channel analysis and uncertainty evaluation for CHF predictions. In addition, it is potentially used for the best estimation of core thermal hydraulic field by incorporating into multiphysics and/or multi-scale code systems. In this study we examined a validation process for the subchannel code MATRA specifically in the prediction of subchannel void distributions. The primary objective of validation is to estimate a range within which the simulation modeling error lies. The experimental data for subchannel void distributions at steady state and transient conditions was provided on the framework of OECD/NEA UAM benchmark program. The validation uncertainty of MATRA code was evaluated for a specific experimental condition by comparing the simulation result and experimental data. A validation process should be preceded by code and solution verification. However, quantification of verification uncertainty was not addressed in this study. The validation uncertainty of the MATRA code for predicting subchannel void distribution was evaluated for a single data point of void fraction measurement at a 5x5 PWR test bundle on the framework of OECD UAM benchmark program. The validation standard uncertainties were evaluated as 4.2%, 3.9%, and 2.8% with the Monte-Carlo approach at the axial levels of 2216 mm, 2669 mm, and 3177 mm, respectively. The sensitivity coefficient approach revealed similar results of uncertainties but did not account for the nonlinear effects on the

  20. Application of coupled codes for safety analysis and licensing issues

    International Nuclear Information System (INIS)

    Langenbuch, S.; Velkov, K.

    2006-01-01

    An overview is given on the development and the advantages of coupled codes which integrate 3D neutron kinetics into thermal-hydraulic system codes. The work performed within GRS by coupling the thermal-hydraulic system code ATHLET and the 3D neutronics code QUABOX/CUBBOX is described as an example. The application of the coupled codes as best-estimate simulation tools for safety analysis is discussed. Some examples from German licensing practices are given which demonstrate how the improved analytical methods of coupled codes have contributed to solve licensing issues related to optimized and more economical use of fuel. (authors)

  1. Improvements, verifications and validations of the BOW code

    International Nuclear Information System (INIS)

    Yu, S.D.; Tayal, M.; Singh, P.N.

    1995-01-01

    The BOW code calculates the lateral deflections of a fuel element consisting of sheath and pellets, due to temperature gradients, hydraulic drag and gravity. the fuel element is subjected to restraint from endplates, neighboring fuel elements and the pressure tube. Many new features have been added to the BOW code since its original release in 1985. This paper outlines the major improvements made to the code and verification/validation results. (author)

  2. Validation of Dose Calculation Codes for Clearance

    International Nuclear Information System (INIS)

    Menon, S.; Wirendal, B.; Bjerler, J.; Studsvik; Teunckens, L.

    2003-01-01

    Various international and national bodies such as the International Atomic Energy Agency, the European Commission, the US Nuclear Regulatory Commission have put forward proposals or guidance documents to regulate the ''clearance'' from regulatory control of very low level radioactive material, in order to allow its recycling as a material management practice. All these proposals are based on predicted scenarios for subsequent utilization of the released materials. The calculation models used in these scenarios tend to utilize conservative data regarding exposure times and dose uptake as well as other assumptions as a safeguard against uncertainties. None of these models has ever been validated by comparison with the actual real life practice of recycling. An international project was organized in order to validate some of the assumptions made in these calculation models, and, thereby, better assess the radiological consequences of recycling on a practical large scale

  3. Verification and Validation of The Tritium Transport Code TMAP7

    International Nuclear Information System (INIS)

    Glen R. Longhurst; James Ambrosek

    2004-01-01

    The TMAP Code was written at the Idaho National Engineering and Environmental Laboratory in the late 1980s as a tool for safety analysis of systems involving tritium. Since then it has been upgraded several times and has been used in numerous applications including experiments supporting fusion safety, predictions for advanced systems such as the International Thermonuclear Experimental Reactor (ITER), and estimates involving tritium production technologies. Its most recent upgrade to TMAP7 was accomplished in response to several needs. Prior versions had the capacity to deal with only a single trap for diffusing gaseous species in solid structures. TMAP7 includes up to three separate traps and up to 10 diffusing species. The original code had difficulty dealing with heteronuclear molecule formation such as HD and DT. That has been removed. Under pre-specified boundary enclosure conditions and solution-law dependent diffusion boundary conditions, such as Sieverts' law, TMAP7 automatically generates heteronuclear molecular partial pressures when solubilities and partial pressures of the homonuclear molecular species are provided for law-dependent diffusion boundary conditions. A further sophistication is the addition of non-diffusing surface species. Atoms such as oxygen or nitrogen or formation of hydroxyl radicals on metal surfaces are sometimes important in molecule formation with diffusing hydrogen isotopes but do not, themselves, diffuse appreciably in the material. TMAP7 will accommodate up to 30 such surface species, allowing the user to specify relationships between those surface concentrations and partial pressures of gaseous species above the surfaces or to form them dynamically by combining diffusion species or other surface species. Additionally, TMAP7 allows the user to include a surface binding energy and an adsorption barrier energy and includes asymmetrical diffusion between the surface sites and regular diffusion sites in the bulk. All of the

  4. Validity of vascular trauma codes at major trauma centres.

    Science.gov (United States)

    Altoijry, Abdulmajeed; Al-Omran, Mohammed; Lindsay, Thomas F; Johnston, K Wayne; Melo, Magda; Mamdani, Muhammad

    2013-12-01

    The use of administrative databases in vascular injury research has been increasing, but the validity of the diagnosis codes used in this research is uncertain. We assessed the positive predictive value (PPV) of International Classification of Diseases, tenth revision (ICD-10), vascular injury codes in administrative claims data in Ontario. We conducted a retrospective validation study using the Canadian Institute for Health Information Discharge Abstract Database, an administrative database that records all hospital admissions in Canada. We evaluated 380 randomly selected hospital discharge abstracts from the 2 main trauma centres in Toronto, Ont., St.Michael's Hospital and Sunnybrook Health Sciences Centre, between Apr. 1, 2002, and Mar. 31, 2010. We then compared these records with the corresponding patients' hospital charts to assess the level of agreement for procedure coding. We calculated the PPV and sensitivity to estimate the validity of vascular injury diagnosis coding. The overall PPV for vascular injury coding was estimated to be 95% (95% confidence interval [CI] 92.3-96.8). The PPV among code groups for neck, thorax, abdomen, upper extremity and lower extremity injuries ranged from 90.8 (95% CI 82.2-95.5) to 97.4 (95% CI 91.0-99.3), whereas sensitivity ranged from 90% (95% CI 81.5-94.8) to 98.7% (95% CI 92.9-99.8). Administrative claims hospital discharge data based on ICD-10 diagnosis codes have a high level of validity when identifying cases of vascular injury. Observational Study Level III.

  5. Heat Transfer treatment in computer codes for safety analysis

    International Nuclear Information System (INIS)

    Jerele, A.; Gregoric, M.

    1984-01-01

    Increased number of operating nuclear power plants has stressed importance of nuclear safety evaluation. For this reason, accordingly to regulatory commission request, safety analyses with computer codes are preformed. In this paper part of this thermohydraulic models dealing with wall-to-fluid heat transfer correlations in computer codes TRAC=PF1, RELAP4/MOD5, RELAP5/MOD1 and COBRA-IV is discussed. (author)

  6. A computer code SPHINCS for sodium fire safety evaluation

    International Nuclear Information System (INIS)

    Yamaguchi, Akira

    2000-01-01

    A computer code SPHINCS solves coupled phenomena of thermal-hydraulics and sodium fire based on a multi-zone model. It deals with arbitrary number of rooms each of which is connected mutually by doorway and penetrations. With regard to the combustion phenomena, flame sheet model and liquid droplet combustion model are used for pool and spray fire, respectively, with the chemical equilibrium model using Gibbs free energy minimization method. The chemical reaction and mass and heat transfer are solved interactively. A specific feature of SPHINCS is detailed representation of thermal-hydraulics of a sodium pool and a steel liner, which is placed on the floor to prevent sodium-concrete contact. The author analyzed a series of pool combustion experiments, in which gas and liner temperatures are measured in detail. It has been found that good agreement is obtained and the SPHINCS has been validated with regard to the pool combustion phenomena. Further research needs are identified for the pool spreading modeling considering thermal deformation of liner and measurement of pool fluidity property of a mixture of liquid sodium and reaction products. SPHINCS code is to be used mainly in the safety evaluation of the consequence of sodium fire accident of liquid metal cooled fast reactor. (author)

  7. Computer codes for level 1 probabilistic safety assessment

    International Nuclear Information System (INIS)

    1990-06-01

    Probabilistic Safety Assessment (PSA) entails several laborious tasks suitable for computer codes assistance. This guide identifies these tasks, presents guidelines for selecting and utilizing computer codes in the conduct of the PSA tasks and for the use of PSA results in safety management and provides information on available codes suggested or applied in performing PSA in nuclear power plants. The guidance is intended for use by nuclear power plant system engineers, safety and operating personnel, and regulators. Large efforts are made today to provide PC-based software systems and PSA processed information in a way to enable their use as a safety management tool by the nuclear power plant overall management. Guidelines on the characteristics of software needed for management to prepare a software that meets their specific needs are also provided. Most of these computer codes are also applicable for PSA of other industrial facilities. The scope of this document is limited to computer codes used for the treatment of internal events. It does not address other codes available mainly for the analysis of external events (e.g. seismic analysis) flood and fire analysis. Codes discussed in the document are those used for probabilistic rather than for phenomenological modelling. It should be also appreciated that these guidelines are not intended to lead the user to selection of one specific code. They provide simply criteria for the selection. Refs and tabs

  8. Code of practice for safety in laboratory - non ionising radiation

    International Nuclear Information System (INIS)

    Ramli Jaya; Mohd Yusof Mohd Ali; Khoo Boo Huat; Khatijah Hashim

    1995-01-01

    The code identifies the non-ionizing radiation encountered in laboratories and the associated hazards. The code is intended as a laboratory standard reference document for general information on safety requirements relating to the usage of non-ionizing radiations in laboratories. The nonionizing radiations cover in this code, namely, are ultraviolet radiation, visible light, radio-frequency radiation, lasers, sound waves and ultrasonic radiation. (author)

  9. Lecture Notes on Criticality Safety Validation Using MCNP & Whisper

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Forrest B. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rising, Michael Evan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Alwin, Jennifer Louise [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-03-11

    Training classes for nuclear criticality safety, MCNP documentation. The need for, and problems surrounding, validation of computer codes and data area considered first. Then some background for MCNP & Whisper is given--best practices for Monte Carlo criticality calculations, neutron spectra, S(α,β) thermal neutron scattering data, nuclear data sensitivities, covariance data, and correlation coefficients. Whisper is computational software designed to assist the nuclear criticality safety analyst with validation studies with the Monte Carlo radiation transport package MCNP. Whisper's methodology (benchmark selection – Ck's, weights; extreme value theory – bias, bias uncertainty; MOS for nuclear data uncertainty – GLLS) and usage are discussed.

  10. Development and validation of a new solver based on the interfacial area transport equation for the numerical simulation of sub-cooled boiling with OpenFOAM CFD code for nuclear safety applications

    Energy Technology Data Exchange (ETDEWEB)

    Alali, Abdullah

    2014-02-21

    The one-group interfacial area transport equation has been coupled to a wall heat flux partitioning model in the framework of two-phase Eulerian approach using the OpenFOAM CFD code for better prediction of subcooled boiling phenomena which is essential for safety analysis of nuclear reactors. The interfacial area transport equation has been modified to include the effect of bubble nucleation at the wall and condensation by subcooled liquid in the bulk that governs the non-uniform bubble size distribution.

  11. Development and validation of a new solver based on the interfacial area transport equation for the numerical simulation of sub-cooled boiling with OpenFOAM CFD code for nuclear safety applications

    International Nuclear Information System (INIS)

    Alali, Abdullah

    2014-01-01

    The one-group interfacial area transport equation has been coupled to a wall heat flux partitioning model in the framework of two-phase Eulerian approach using the OpenFOAM CFD code for better prediction of subcooled boiling phenomena which is essential for safety analysis of nuclear reactors. The interfacial area transport equation has been modified to include the effect of bubble nucleation at the wall and condensation by subcooled liquid in the bulk that governs the non-uniform bubble size distribution.

  12. GOTHIC-IST 6.1b code validation exercises relating to heat removal by dousing and air coolers in CANDU containment

    International Nuclear Information System (INIS)

    Ramachandran, S.; Krause, M.; Nguyen, T.

    2003-01-01

    This paper presents validation results relating to the use of the GOTHIC containment analysis code for CANDU safety analysis. The validation results indicate that GOTHIC predicts heat removal by dousing and air cooler heat transfer with reasonable accuracy. (author)

  13. Code of Conduct on the Safety of Research Reactors

    International Nuclear Information System (INIS)

    2006-09-01

    The Board of Governors of the International Atomic Energy Agency (IAEA) adopted the Code of Conduct on the Safety of Research Reactors on 8 March 2004. The Board's action was the culmination of several years of work to develop the Code and obtain a consensus on its provisions. The process leading to the Code began in 1998, when the International Nuclear Safety Advisory Group (INSAG) informed the Director General of concerns about the safety of research reactors. In 2000, INSAG recommended that the Secretariat begin developing an international protocol or a similar legal instrument to address those concerns. In September 2000, in resolution GC(44)/RES/14, the General Conference requested the Secretariat ''within its available resources, to continue work on exploring options to strengthen the international nuclear safety arrangements for civil research reactors, taking due account of input from INSAG and the views of other relevant bodies''. A working group convened by the Secretariat pursuant to that request recommended that ''the Agency consider establishing an international action plan for research reactors'' and that the action plan include preparation of a Code of Conduct ''that would clearly establish the desirable attributes for management of research reactor safety''. In September 2001, the Board requested that the Secretariat develop and implement, in conjunction with Member States, an international research reactor safety enhancement plan which included preparation of a Code of Conduct on the Safety of Research Reactors. Subsequently, in resolution GC(45)/RES/10.A, the General Conference endorsed the Board's request. Pursuant to that request, a Code of Conduct on the Safety of Research Reactors was drafted at two meetings of an Open-ended Working Group of Legal and Technical Experts. This draft Code of Conduct was circulated to all Member States for comment. On the basis of the responses received, a revised draft of the Code was prepared by the Secretariat

  14. Gap conductance model validation in the TASS/SMR-S code

    International Nuclear Information System (INIS)

    Ahn, Sang-Jun; Yang, Soo-Hyung; Chung, Young-Jong; Bae, Kyoo-Hwan; Lee, Won-Jae

    2011-01-01

    An advanced integral pressurized water reactor, SMART (System-Integrated Modular Advanced ReacTor) has been developed by KAERI (Korea Atomic Energy Research and Institute). The purposes of the SMART are sea water desalination and an electricity generation. For the safety evaluation and performance analysis of the SMART, TASS/SMR-S (Transient And Setpoint Simulation/System-integrated Modular Reactor) code, has been developed. In this paper, the gap conductance model for the calculation of gap conductance has been validated by using another system code, MARS code, and experimental results. In the validation, the behaviors of fuel temperature and gap width are selected as the major parameters. According to the evaluation results, the TASS/SMR-S code predicts well the behaviors of fuel temperatures and gap width variation, compared to the MARS calculation results and experimental data. (author)

  15. Multi-dimensional Code Development for Safety Analysis of LMR

    International Nuclear Information System (INIS)

    Ha, K. S.; Jeong, H. Y.; Kwon, Y. M.; Lee, Y. B.

    2006-08-01

    A liquid metal reactor loaded a metallic fuel has the inherent safety mechanism due to the several negative reactivity feedback. Although this feature demonstrated through experiments in the EBR-II, any of the computer programs until now did not exactly analyze it because of the complexity of the reactivity feedback mechanism. A multi-dimensional detail program was developed through the International Nuclear Energy Research Initiative(INERI) from 2003 to 2005. This report includes the numerical coupling the multi-dimensional program and SSC-K code which is used to the safety analysis of liquid metal reactors in KAERI. The coupled code has been proved by comparing the analysis results using the code with the results using SAS-SASSYS code of ANL for the UTOP, ULOF, and ULOHS applied to the safety analysis for KALIMER-150

  16. Compendium of computer codes for the safety analysis of LMFBR's

    International Nuclear Information System (INIS)

    1975-06-01

    A high level of mathematical sophistication is required in the safety analysis of LMFBR's to adequately meet the demands for realism and confidence in all areas of accident consequence evaluation. The numerical solution procedures associated with these analyses are generally so complex and time consuming as to necessitate their programming into computer codes. These computer codes have become extremely powerful tools for safety analysis, combining unique advantages in accuracy, speed and cost. The number, diversity and complexity of LMFBR safety codes in the U. S. has grown rapidly in recent years. It is estimated that over 100 such codes exist in various stages of development throughout the country. It is inevitable that such a large assortment of codes will require rigorous cataloguing and abstracting to aid individuals in identifying what is available. It is the purpose of this compendium to provide such a service through the compilation of code summaries which describe and clarify the status of domestic LMFBR safety codes. (U.S.)

  17. Development and improvement of safety analysis code for geological disposal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-15

    In order to confirm the long-term safety concerning geological disposal, probabilistic safety assessment code and other analysis codes, which can evaluate possibility of each event and influence on engineered barrier and natural barrier by the event, were introduced. We confirmed basic functions of those codes and studied the relation between those functions and FEP/PID which should be taken into consideration in safety assessment. We are planning to develop 'Nuclide Migration Assessment System' for the purpose of realizing improvement in efficiency of assessment work, human error prevention for analysis, and quality assurance of the analysis environment and analysis work for safety assessment by using it. As the first step, we defined the system requirements and decided the system composition and functions which should be mounted in them based on those requirements. (author)

  18. Development and validation of a nodal code for core calculation

    International Nuclear Information System (INIS)

    Nowakowski, Pedro Mariano

    2004-01-01

    The code RHENO solves the multigroup three-dimensional diffusion equation using a nodal method of polynomial expansion.A comparative study has been made between this code and present internationals nodal diffusion codes, resulting that the RHENO is up to date.The RHENO has been integrated to a calculation line and has been extend to make burnup calculations.Two methods for pin power reconstruction were developed: modulation and imbedded. The modulation method has been implemented in a program, while the implementation of the imbedded method will be concluded shortly.The validation carried out (that includes experimental data of a MPR) show very good results and calculation efficiency

  19. Verification and Validation of the Tritium Transport Code TMAP7

    International Nuclear Information System (INIS)

    Longhurst, Glen R.; Ambrosek, James

    2005-01-01

    The TMAP code has been upgraded to version 7, which includes radioactive decay along with many features implemented in prior versions. Pursuant to acceptance and release for distribution, the code was exercised in a variety of problem types to demonstrate that it provides results in agreement with theoretical results for cases where those are available. It has also been used to model certain experimental results. In this paper, the capabilities of the TMAP7 code are demonstrated by presenting some of the results from the verification and validation process

  20. Validating the BISON fuel performance code to integral LWR experiments

    Energy Technology Data Exchange (ETDEWEB)

    Williamson, R.L., E-mail: Richard.Williamson@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Gamble, K.A., E-mail: Kyle.Gamble@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Perez, D.M., E-mail: Danielle.Perez@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Novascone, S.R., E-mail: Stephen.Novascone@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Pastore, G., E-mail: Giovanni.Pastore@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Gardner, R.J., E-mail: Russell.Gardner@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Hales, J.D., E-mail: Jason.Hales@inl.gov [Fuel Modeling and Simulation, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-3840 (United States); Liu, W., E-mail: Wenfeng.Liu@anatech.com [ANATECH Corporation, 5435 Oberlin Dr., San Diego, CA 92121 (United States); Mai, A., E-mail: Anh.Mai@anatech.com [ANATECH Corporation, 5435 Oberlin Dr., San Diego, CA 92121 (United States)

    2016-05-15

    Highlights: • The BISON multidimensional fuel performance code is being validated to integral LWR experiments. • Code and solution verification are necessary prerequisites to validation. • Fuel centerline temperature comparisons through all phases of fuel life are very reasonable. • Accuracy in predicting fission gas release is consistent with state-of-the-art modeling and the involved uncertainties. • Rod diameter comparisons are not satisfactory and further investigation is underway. - Abstract: BISON is a modern finite element-based nuclear fuel performance code that has been under development at Idaho National Laboratory (INL) since 2009. The code is applicable to both steady and transient fuel behavior and has been used to analyze a variety of fuel forms in 1D spherical, 2D axisymmetric, or 3D geometries. Code validation is underway and is the subject of this study. A brief overview of BISON's computational framework, governing equations, and general material and behavioral models is provided. BISON code and solution verification procedures are described, followed by a summary of the experimental data used to date for validation of Light Water Reactor (LWR) fuel. Validation comparisons focus on fuel centerline temperature, fission gas release, and rod diameter both before and following fuel-clad mechanical contact. Comparisons for 35 LWR rods are consolidated to provide an overall view of how the code is predicting physical behavior, with a few select validation cases discussed in greater detail. Results demonstrate that (1) fuel centerline temperature comparisons through all phases of fuel life are very reasonable with deviations between predictions and experimental data within ±10% for early life through high burnup fuel and only slightly out of these bounds for power ramp experiments, (2) accuracy in predicting fission gas release appears to be consistent with state-of-the-art modeling and with the involved uncertainties and (3) comparison

  1. 78 FR 5866 - Pipeline Safety: Annual Reports and Validation

    Science.gov (United States)

    2013-01-28

    ... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration [Docket ID PHMSA-2012-0319] Pipeline Safety: Annual Reports and Validation AGENCY: Pipeline and Hazardous Materials... 2012 gas transmission and gathering annual reports, remind pipeline owners and operators to validate...

  2. Independent peer review of nuclear safety computer codes

    International Nuclear Information System (INIS)

    Boyack, B.E.; Jenks, R.P.

    1993-01-01

    A structured, independent computer code peer-review process has been developed to assist the US Nuclear Regulatory Commission (NRC) and the US Department of Energy in their nuclear safety missions. This paper describes a structured process of independent code peer review, benefits associated with a code-independent peer review, as well as the authors' recent peer-review experience. The NRC adheres to the principle that safety of plant design, construction, and operation are the responsibility of the licensee. Nevertheless, NRC staff must have the ability to independently assess plant designs and safety analyses submitted by license applicants. According to Ref. 1, open-quotes this requires that a sound understanding be obtained of the important physical phenomena that may occur during transients in operating power plants.close quotes The NRC concluded that computer codes are the principal products to open-quotes understand and predict plant response to deviations from normal operating conditionsclose quotes and has developed several codes for that purpose. However, codes cannot be used blindly; they must be assessed and found adequate for the purposes they are intended. A key part of the qualification process can be accomplished through code peer reviews; this approach has been adopted by the NRC

  3. Automation of RELAP5 input calibration and code validation using genetic algorithm

    International Nuclear Information System (INIS)

    Phung, Viet-Anh; Kööp, Kaspar; Grishchenko, Dmitry; Vorobyev, Yury; Kudinov, Pavel

    2016-01-01

    Highlights: • Automated input calibration and code validation using genetic algorithm is presented. • Predictions generally overlap experiments for individual system response quantities (SRQs). • It was not possible to predict simultaneously experimental maximum flow rate and oscillation period. • Simultaneous consideration of multiple SRQs is important for code validation. - Abstract: Validation of system thermal-hydraulic codes is an important step in application of the codes to reactor safety analysis. The goal of the validation process is to determine how well a code can represent physical reality. This is achieved by comparing predicted and experimental system response quantities (SRQs) taking into account experimental and modelling uncertainties. Parameters which are required for the code input but not measured directly in the experiment can become an important source of uncertainty in the code validation process. Quantification of such parameters is often called input calibration. Calibration and uncertainty quantification may become challenging tasks when the number of calibrated input parameters and SRQs is large and dependencies between them are complex. If only engineering judgment is employed in the process, the outcome can be prone to so called “user effects”. The goal of this work is to develop an automated approach to input calibration and RELAP5 code validation against data on two-phase natural circulation flow instability. Multiple SRQs are used in both calibration and validation. In the input calibration, we used genetic algorithm (GA), a heuristic global optimization method, in order to minimize the discrepancy between experimental and simulation data by identifying optimal combinations of uncertain input parameters in the calibration process. We demonstrate the importance of the proper selection of SRQs and respective normalization and weighting factors in the fitness function. In the code validation, we used maximum flow rate as the

  4. Automation of RELAP5 input calibration and code validation using genetic algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Phung, Viet-Anh, E-mail: vaphung@kth.se [Division of Nuclear Power Safety, Royal Institute of Technology, Roslagstullsbacken 21, 10691 Stockholm (Sweden); Kööp, Kaspar, E-mail: kaspar@safety.sci.kth.se [Division of Nuclear Power Safety, Royal Institute of Technology, Roslagstullsbacken 21, 10691 Stockholm (Sweden); Grishchenko, Dmitry, E-mail: dmitry@safety.sci.kth.se [Division of Nuclear Power Safety, Royal Institute of Technology, Roslagstullsbacken 21, 10691 Stockholm (Sweden); Vorobyev, Yury, E-mail: yura3510@gmail.com [National Research Center “Kurchatov Institute”, Kurchatov square 1, Moscow 123182 (Russian Federation); Kudinov, Pavel, E-mail: pavel@safety.sci.kth.se [Division of Nuclear Power Safety, Royal Institute of Technology, Roslagstullsbacken 21, 10691 Stockholm (Sweden)

    2016-04-15

    Highlights: • Automated input calibration and code validation using genetic algorithm is presented. • Predictions generally overlap experiments for individual system response quantities (SRQs). • It was not possible to predict simultaneously experimental maximum flow rate and oscillation period. • Simultaneous consideration of multiple SRQs is important for code validation. - Abstract: Validation of system thermal-hydraulic codes is an important step in application of the codes to reactor safety analysis. The goal of the validation process is to determine how well a code can represent physical reality. This is achieved by comparing predicted and experimental system response quantities (SRQs) taking into account experimental and modelling uncertainties. Parameters which are required for the code input but not measured directly in the experiment can become an important source of uncertainty in the code validation process. Quantification of such parameters is often called input calibration. Calibration and uncertainty quantification may become challenging tasks when the number of calibrated input parameters and SRQs is large and dependencies between them are complex. If only engineering judgment is employed in the process, the outcome can be prone to so called “user effects”. The goal of this work is to develop an automated approach to input calibration and RELAP5 code validation against data on two-phase natural circulation flow instability. Multiple SRQs are used in both calibration and validation. In the input calibration, we used genetic algorithm (GA), a heuristic global optimization method, in order to minimize the discrepancy between experimental and simulation data by identifying optimal combinations of uncertain input parameters in the calibration process. We demonstrate the importance of the proper selection of SRQs and respective normalization and weighting factors in the fitness function. In the code validation, we used maximum flow rate as the

  5. Lawrence Livermore National Laboratory Probabilistic Seismic Hazard Codes Validation

    International Nuclear Information System (INIS)

    Savy, J B

    2003-01-01

    Probabilistic Seismic Hazard Analysis (PSHA) is a methodology that estimates the likelihood that various levels of earthquake-caused ground motion will be exceeded at a given location in a given future time-period. LLNL has been developing the methodology and codes in support of the Nuclear Regulatory Commission (NRC) needs for reviews of site licensing of nuclear power plants, since 1978. A number of existing computer codes have been validated and still can lead to ranges of hazard estimates in some cases. Until now, the seismic hazard community had not agreed on any specific method for evaluation of these codes. The Earthquake Engineering Research Institute (EERI) and the Pacific Engineering Earthquake Research (PEER) center organized an exercise in testing of existing codes with the aim of developing a series of standard tests that future developers could use to evaluate and calibrate their own codes. Seven code developers participated in the exercise, on a voluntary basis. Lawrence Livermore National laboratory participated with some support from the NRC. The final product of the study will include a series of criteria for judging of the validity of the results provided by a computer code. This EERI/PEER project was first planned to be completed by June of 2003. As the group neared completion of the tests, the managing team decided that new tests were necessary. As a result, the present report documents only the work performed to this point. It demonstrates that the computer codes developed by LLNL perform all calculations correctly and as intended. Differences exist between the results of the codes tested, that are attributed to a series of assumptions, on the parameters and models, that the developers had to make. The managing team is planning a new series of tests to help in reaching a consensus on these assumptions

  6. The Mistra experiment for field containment code validation first results

    International Nuclear Information System (INIS)

    Caron-Charles, M.; Blumenfeld, L.

    2001-01-01

    The MISTRA facility is a large scale experiment, designed for the purpose of thermal-hydraulics multi-D codes validation. A short description of the facility, the set up of the instrumentation and the test program are presented. Then, the first experimental results, studying helium injection in the containment and their calculations are detailed. (author)

  7. Experimental validation of the containment codes ASTARTE and SEURBNUK

    International Nuclear Information System (INIS)

    Kendall, K.C.; Arnold, L.A.; Broadhouse, B.J.; Jones, A.; Yerkess, A.; Benuzzi, A.

    1979-10-01

    The fast reactor containment codes ASTARTE and SEURBNUK are being validated against data from the COVA series of small scale experiments being performed jointly by the UKAEA and JRC Ispra. The experimental programme is nearly complete, and data are given. (U.K.)

  8. Validation and application of the system code ATHLET-CD for BWR severe accident analyses

    Energy Technology Data Exchange (ETDEWEB)

    Di Marcello, Valentino, E-mail: valentino.marcello@kit.edu; Imke, Uwe; Sanchez, Victor

    2016-10-15

    Highlights: • We present the application of the system code ATHLET-CD code for BWR safety analyses. • Validation of core in-vessel models is performed based on KIT CORA experiments. • A SB-LOCA scenario is simulated on a generic German BWR plant up to vessel failure. • Different core reflooding possibilities are investigated to mitigate the accident consequences. • ATHLET-CD modelling features reflect the current state of the art of severe accident codes. - Abstract: This paper is aimed at the validation and application of the system code ATHLET-CD for the simulation of severe accident phenomena in Boiling Water Reactors (BWR). The corresponding models for core degradation behaviour e.g., oxidation, melting and relocation of core structural components are validated against experimental data available from the CORA-16 and -17 bundle tests. Model weaknesses are discussed along with needs for further code improvements. With the validated ATHLET-CD code, calculations are performed to assess the code capabilities for the prediction of in-vessel late phase core behaviour and reflooding of damaged fuel rods. For this purpose, a small break LOCA scenario for a generic German BWR with postulated multiple failures of the safety systems was selected. In the analysis, accident management measures represented by cold water injection into the damaged reactor core are addressed to investigate the efficacy in avoiding or delaying the failure of the reactor pressure vessel. Results show that ATHLET-CD is applicable to the description of BWR plant behaviour with reliable physical models and numerical methods adopted for the description of key in-vessel phenomena.

  9. Validation testing of safety-critical software

    International Nuclear Information System (INIS)

    Kim, Hang Bae; Han, Jae Bok

    1995-01-01

    A software engineering process has been developed for the design of safety critical software for Wolsung 2/3/4 project to satisfy the requirements of the regulatory body. Among the process, this paper described the detail process of validation testing performed to ensure that the software with its hardware, developed by the design group, satisfies the requirements of the functional specification prepared by the independent functional group. To perform the tests, test facility and test software were developed and actual safety system computer was connected. Three kinds of test cases, i.e., functional test, performance test and self-check test, were programmed and run to verify each functional specifications. Test failures were feedback to the design group to revise the software and test results were analyzed and documented in the report to submit to the regulatory body. The test methodology and procedure were very efficient and satisfactory to perform the systematic and automatic test. The test results were also acceptable and successful to verify the software acts as specified in the program functional specification. This methodology can be applied to the validation of other safety-critical software. 2 figs., 2 tabs., 14 refs. (Author)

  10. Development of Regulatory Audit Core Safety Code : COREDAX

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Chae Yong; Jo, Jong Chull; Roh, Byung Hwan [Korea Institute of Nuclear Safety, Taejon (Korea, Republic of); Lee, Jae Jun; Cho, Nam Zin [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

    2005-07-01

    Korea Institute of Nuclear Safety (KINS) has developed a core neutronics simulator, COREDAX code, for verifying core safety of SMART-P reactor, which is technically supported by Korea Advanced Institute of Science and Technology (KAIST). The COREDAX code would be used for regulatory audit calculations of 3- dimendional core neutronics. The COREDAX code solves the steady-state and timedependent multi-group neutron diffusion equation in hexagonal geometry as well as rectangular geometry by analytic function expansion nodal (AFEN) method. AFEN method was developed at KAIST, and it was internationally verified that its accuracy is excellent. The COREDAX code is originally programmed based on the AFEN method. Accuracy of the code on the AFEN method was excellent for the hexagonal 2-dimensional problems, but there was a need for improvement for hexagonal-z 3-dimensional problems. Hence, several solution routines of the AFEN method are improved, and finally the advanced AFEN method is created. COREDAX code is based on the advanced AFEN method . The initial version of COREDAX code is to complete a basic framework, performing eigenvalue calculations and kinetics calculations with thermal-hydraulic feedbacks, for audit calculations of steady-state core design and reactivity-induced accidents of SMART-P reactor. This study describes the COREDAX code for hexagonal geometry.

  11. Validation of system codes RELAP5 and SPECTRA for natural convection boiling in narrow channels

    Energy Technology Data Exchange (ETDEWEB)

    Stempniewicz, M.M., E-mail: stempniewicz@nrg.eu; Slootman, M.L.F.; Wiersema, H.T.

    2016-10-15

    Highlights: • Computer codes RELAP5/Mod3.3 and SPECTRA 3.61 validated for boiling in narrow channels. • Validated codes can be used for LOCA analyses in research reactors. • Code validation based on natural convection boiling in narrow channels experiments. - Abstract: Safety analyses of LOCA scenarios in nuclear power plants are performed with so called thermal–hydraulic system codes, such as RELAP5. Such codes are validated for typical fuel geometries applied in nuclear power plants. The question considered by this article is if the codes can be applied for LOCA analyses in research reactors, in particular exceeding CHF in very narrow channels. In order to answer this question, validation calculations were performed with two thermal–hydraulic system codes: RELAP and SPECTRA. The validation was based on natural convection boiling in narrow channels experiments, performed by Prof. Monde et al. in the years 1990–2000. In total 42 vertical tube and annulus experiments were simulated with both codes. A good agreement of the calculated values with the measured data was observed. The main conclusions are: • The computer codes RELAP5/Mod 3.3 (US NRC version) and SPECTRA 3.61 have been validated for natural convection boiling in narrow channels using experiments of Monde. The dimensions applied in the experiments were performed for a range that covers the values observed in typical research reactors. Therefore it is concluded that both codes are validated and can be used for LOCA analyses in research reactors, including natural convection boiling. The applicability range of the present validation is: hydraulic diameters of 1.1 ⩽ D{sub hyd} ⩽ 9.0 mm, heated lengths of 0.1 ⩽ L ⩽ 1.0 m, pressures of 0.10 ⩽ P ⩽ 0.99 MPa. In most calculations the burnout was predicted to occur at lower power than that observed in the experiments. In several cases the burnout was observed at higher power. The overprediction was not larger than 16% in RELAP and 15% in

  12. AEEW comments on the NNC/CEGB LOCA code validation report RX 440-A

    International Nuclear Information System (INIS)

    Brittain, I.; Bryce, W.M.; O'Mahoney, R.; Richards, C.G.; Gibson, I.H.; Porter, W.H.L.; Fell, J.

    1984-03-01

    Comments are made on the NNC/CEGB report PWR/RX 440-A, Review of Validation for the ECCS Evaluation Model Codes, by K.T. Routledge et al, 1982. This set out to review methods and models used in the LOCA safety case for Sizewell B. These methods are embodied in the Evaluation Model Computer codes SATAN-VI, WREFLOOD, WFLASH, LOCTA-IV and COCO. The main application of these codes is the determination of peak clad temperature and overall containment pressure. The comments represent the views of a group which has been involved for a number of years in the development and application of Best-Estimate methods for LOCA analysis. It is the judgement of this group that, overall, the EM methods can be used to make an acceptable safety case, but there are a number of points of detail still to be resolved. (U.K.)

  13. System verification and validation report for the TMAD code

    International Nuclear Information System (INIS)

    Finfrock, S.H.

    1995-01-01

    This document serves as the Verification and Validation Report for the TMAD code system, which includes the TMAD code and the LIBMAKR Code. The TMAD code was commissioned to facilitate the interpretation of moisture probe measurements in the Hanford Site waste tanks. In principle, the code is an interpolation routine that acts over a library of benchmark data based on two independent variables, typically anomaly size and moisture content. Two additional variables, anomaly type and detector type, can also be considered independent variables, but no interpolation is done over them. The dependent variable is detector response. The intent is to provide the code with measured detector responses from two or more detectors. The code will then interrogate (and interpolate upon) the benchmark data library and find the anomaly-type/anomaly-size/moisture-content combination that provides the closest match to the measured data. The primary purpose of this document is to provide the results of the system testing and the conclusions based thereon. The results of the testing process are documented in the body of the report. Appendix A gives the test plan, including test procedures, used in conducting the tests. Appendix B lists the input data required to conduct the tests, and Appendices C and 0 list the numerical results of the tests

  14. Verification and validation of the PLTEMP/ANL code for thermal hydraulic analysis of experimental and test reactors

    International Nuclear Information System (INIS)

    Kalimullah, M.; Olson, A.O.; Feldman, E.E.; Hanan, N.; Dionne, B.

    2012-01-01

    The document compiles in a single volume several verification and validation works done for the PLTEMP/ANL code during the years of its development and improvement. Some works that are available in the open literature are simply referenced at the outset, and are not included in the document. PLTEMP has been used in conversion safety analysis reports of several US and foreign research reactors that have been licensed and converted. A list of such reactors is given. Each chapter of the document deals with the verification or validation of a specific model. The model verification is usually done by comparing the code with hand calculation, Microsoft spreadsheet calculation, or Mathematica calculation. The model validation is done by comparing the code with experimental data or a more validated code like the RELAP5 code.

  15. Verification and Validation of the PLTEMP/ANL Code for Thermal-Hydraulic Analysis of Experimental and Test Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Kalimullah, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Olson, Arne P. [Argonne National Lab. (ANL), Argonne, IL (United States); Feldman, E. E. [Argonne National Lab. (ANL), Argonne, IL (United States); Hanan, N. [Argonne National Lab. (ANL), Argonne, IL (United States); Dionne, B. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-04-07

    The document compiles in a single volume several verification and validation works done for the PLTEMP/ANL code during the years of its development and improvement. Some works that are available in the open literature are simply referenced at the outset, and are not included in the document. PLTEMP has been used in conversion safety analysis reports of several US and foreign research reactors that have been licensed and converted. A list of such reactors is given. Each chapter of the document deals with the verification or validation of a specific model. The model verification is usually done by comparing the code with hand calculation, Microsoft spreadsheet calculation, or Mathematica calculation. The model validation is done by comparing the code with experimental data or a more validated code like the RELAP5 code.

  16. Foundational development of an advanced nuclear reactor integrated safety code

    International Nuclear Information System (INIS)

    Clarno, Kevin; Lorber, Alfred Abraham; Pryor, Richard J.; Spotz, William F.; Schmidt, Rodney Cannon; Belcourt, Kenneth; Hooper, Russell Warren; Humphries, Larry LaRon

    2010-01-01

    This report describes the activities and results of a Sandia LDRD project whose objective was to develop and demonstrate foundational aspects of a next-generation nuclear reactor safety code that leverages advanced computational technology. The project scope was directed towards the systems-level modeling and simulation of an advanced, sodium cooled fast reactor, but the approach developed has a more general applicability. The major accomplishments of the LDRD are centered around the following two activities. (1) The development and testing of LIME, a Lightweight Integrating Multi-physics Environment for coupling codes that is designed to enable both 'legacy' and 'new' physics codes to be combined and strongly coupled using advanced nonlinear solution methods. (2) The development and initial demonstration of BRISC, a prototype next-generation nuclear reactor integrated safety code. BRISC leverages LIME to tightly couple the physics models in several different codes (written in a variety of languages) into one integrated package for simulating accident scenarios in a liquid sodium cooled 'burner' nuclear reactor. Other activities and accomplishments of the LDRD include (a) further development, application and demonstration of the 'non-linear elimination' strategy to enable physics codes that do not provide residuals to be incorporated into LIME, (b) significant extensions of the RIO CFD code capabilities, (c) complex 3D solid modeling and meshing of major fast reactor components and regions, and (d) an approach for multi-physics coupling across non-conformal mesh interfaces.

  17. Foundational development of an advanced nuclear reactor integrated safety code.

    Energy Technology Data Exchange (ETDEWEB)

    Clarno, Kevin (Oak Ridge National Laboratory, Oak Ridge, TN); Lorber, Alfred Abraham; Pryor, Richard J.; Spotz, William F.; Schmidt, Rodney Cannon; Belcourt, Kenneth (Ktech Corporation, Albuquerque, NM); Hooper, Russell Warren; Humphries, Larry LaRon

    2010-02-01

    This report describes the activities and results of a Sandia LDRD project whose objective was to develop and demonstrate foundational aspects of a next-generation nuclear reactor safety code that leverages advanced computational technology. The project scope was directed towards the systems-level modeling and simulation of an advanced, sodium cooled fast reactor, but the approach developed has a more general applicability. The major accomplishments of the LDRD are centered around the following two activities. (1) The development and testing of LIME, a Lightweight Integrating Multi-physics Environment for coupling codes that is designed to enable both 'legacy' and 'new' physics codes to be combined and strongly coupled using advanced nonlinear solution methods. (2) The development and initial demonstration of BRISC, a prototype next-generation nuclear reactor integrated safety code. BRISC leverages LIME to tightly couple the physics models in several different codes (written in a variety of languages) into one integrated package for simulating accident scenarios in a liquid sodium cooled 'burner' nuclear reactor. Other activities and accomplishments of the LDRD include (a) further development, application and demonstration of the 'non-linear elimination' strategy to enable physics codes that do not provide residuals to be incorporated into LIME, (b) significant extensions of the RIO CFD code capabilities, (c) complex 3D solid modeling and meshing of major fast reactor components and regions, and (d) an approach for multi-physics coupling across non-conformal mesh interfaces.

  18. Method for quantitative assessment of nuclear safety computer codes

    International Nuclear Information System (INIS)

    Dearien, J.A.; Davis, C.B.; Matthews, L.J.

    1979-01-01

    A procedure has been developed for the quantitative assessment of nuclear safety computer codes and tested by comparison of RELAP4/MOD6 predictions with results from two Semiscale tests. This paper describes the developed procedure, the application of the procedure to the Semiscale tests, and the results obtained from the comparison

  19. Verification and validation of the THYTAN code for the graphite oxidation analysis in the HTGR systems

    International Nuclear Information System (INIS)

    Shimazaki, Yosuke; Isaka, Kazuyoshi; Nomoto, Yasunobu; Seki, Tomokazu; Ohashi, Hirofumi

    2014-12-01

    The analytical models for the evaluation of graphite oxidation were implemented into the THYTAN code, which employs the mass balance and a node-link computational scheme to evaluate tritium behavior in the High Temperature Gas-cooled Reactor (HTGR) systems for hydrogen production, to analyze the graphite oxidation during the air or water ingress accidents in the HTGR systems. This report describes the analytical models of the THYTAN code in terms of the graphite oxidation analysis and its verification and validation (V and V) results. Mass transfer from the gas mixture in the coolant channel to the graphite surface, diffusion in the graphite, graphite oxidation by air or water, chemical reaction and release from the primary circuit to the containment vessel by a safety valve were modeled to calculate the mass balance in the graphite and the gas mixture in the coolant channel. The computed solutions using the THYTAN code for simple questions were compared to the analytical results by a hand calculation to verify the algorithms for each implemented analytical model. A representation of the graphite oxidation experimental was analyzed using the THYTAN code, and the results were compared to the experimental data and the computed solutions using the GRACE code, which was used for the safety analysis of the High Temperature Engineering Test Reactor (HTTR), in regard to corrosion depth of graphite and oxygen concentration at the outlet of the test section to validate the analytical models of the THYTAN code. The comparison of THYTAN code results with the analytical solutions, experimental data and the GRACE code results showed the good agreement. (author)

  20. IAEA codes and guides for safety of nuclear power plants

    International Nuclear Information System (INIS)

    Raisic, N.

    1980-01-01

    The objectives and scope of the Agency's programme of nuclear safety standards are described and the role of these documents in regulation of nuclear power im Member States is discussed. For each of the five areas of safety standards development, i.e. siting, design, operation, quality assurance and governmental organization, a set of principles underlying requirements and recommendations contained in the Code of Practice and Safety Guides will be presented. Safety Guides in each of the five areas will be reviewed in respect of the scope and content. A consideration will be given to the future development of the safety standards and to the revision and updating of the published documents. (orig./RW)

  1. Development and preliminary validation of flux map processing code MAPLE

    International Nuclear Information System (INIS)

    Li Wenhuai; Zhang Xiangju; Dang Zhen; Chen Ming'an; Lu Haoliang; Li Jinggang; Wu Yuanbao

    2013-01-01

    The self-reliant flux map processing code MAPLE was developed by China General Nuclear Power Corporation (CGN). Weight coefficient method (WCM), polynomial expand method (PEM) and thin plane spline (TPS) method were applied to fit the deviation between measured and predicted detector signal results for two-dimensional radial plane, to interpolate or extrapolate the non-instrumented location deviation. Comparison of results in the test cases shows that the TPS method can better capture the information of curved fitting lines than the other methods. The measured flux map data of the Lingao Nuclear Power Plant were processed using MAPLE as validation test cases, combined with SMART code. Validation results show that the calculation results of MAPLE are reasonable and satisfied. (authors)

  2. Preliminary study for unified management of CANDU safety codes and construction of database system

    International Nuclear Information System (INIS)

    Min, Byung Joo; Kim, Hyoung Tae

    2003-03-01

    It is needed to develop the Graphical User Interface(GUI) for the unified management of CANDU safety codes and to construct database system for the validation of safety codes, for which the preliminary study is done in the first stage of the present work. The input and output structures and data flow of CATHENA and PRESCON2 are investigated and the interaction of the variables between CATHENA and PRESCON2 are identified. Furthermore, PC versions of CATHENA and PRESCON2 codes are developed for the interaction of these codes and GUI(Graphic User Interface). The PC versions are assessed by comparing the calculation results with those by HP workstation or from FSAR(Final Safety Analysis Report). Preliminary study on the GUI for the safety codes in the unified management system are done. The sample of GUI programming is demonstrated preliminarily. Visual C++ is selected as the programming language for the development of GUI system. The data for Wolsong plants, reactor core, and thermal-hydraulic experiments executed in the inside and outside of the country, are collected and classified following the structure of the database system, of which two types are considered for the final web-based database system. The preliminary GUI programming for database system is demonstrated, which is updated in the future work

  3. CFD Code Validation against Stratified Air-Water Flow Experimental Data

    Directory of Open Access Journals (Sweden)

    F. Terzuoli

    2008-01-01

    Full Text Available Pressurized thermal shock (PTS modelling has been identified as one of the most important industrial needs related to nuclear reactor safety. A severe PTS scenario limiting the reactor pressure vessel (RPV lifetime is the cold water emergency core cooling (ECC injection into the cold leg during a loss of coolant accident (LOCA. Since it represents a big challenge for numerical simulations, this scenario was selected within the European Platform for Nuclear Reactor Simulations (NURESIM Integrated Project as a reference two-phase problem for computational fluid dynamics (CFDs code validation. This paper presents a CFD analysis of a stratified air-water flow experimental investigation performed at the Institut de Mécanique des Fluides de Toulouse in 1985, which shares some common physical features with the ECC injection in PWR cold leg. Numerical simulations have been carried out with two commercial codes (Fluent and Ansys CFX, and a research code (NEPTUNE CFD. The aim of this work, carried out at the University of Pisa within the NURESIM IP, is to validate the free surface flow model implemented in the codes against experimental data, and to perform code-to-code benchmarking. Obtained results suggest the relevance of three-dimensional effects and stress the importance of a suitable interface drag modelling.

  4. CFD Code Validation against Stratified Air-Water Flow Experimental Data

    International Nuclear Information System (INIS)

    Terzuoli, F.; Galassi, M.C.; Mazzini, D.; D'Auria, F.

    2008-01-01

    Pressurized thermal shock (PTS) modelling has been identified as one of the most important industrial needs related to nuclear reactor safety. A severe PTS scenario limiting the reactor pressure vessel (RPV) lifetime is the cold water emergency core cooling (ECC) injection into the cold leg during a loss of coolant accident (LOCA). Since it represents a big challenge for numerical simulations, this scenario was selected within the European Platform for Nuclear Reactor Simulations (NURESIM) Integrated Project as a reference two-phase problem for computational fluid dynamics (CFDs) code validation. This paper presents a CFD analysis of a stratified air-water flow experimental investigation performed at the Institut de Mecanique des Fluides de Toulouse in 1985, which shares some common physical features with the ECC injection in PWR cold leg. Numerical simulations have been carried out with two commercial codes (Fluent and Ansys CFX), and a research code (NEPTUNE CFD). The aim of this work, carried out at the University of Pisa within the NURESIM IP, is to validate the free surface flow model implemented in the codes against experimental data, and to perform code-to-code benchmarking. Obtained results suggest the relevance of three-dimensional effects and stress the importance of a suitable interface drag modelling

  5. Perspectives on the development of next generation reactor systems safety analysis codes

    International Nuclear Information System (INIS)

    Zhang, H.

    2015-01-01

    tackle the deficiencies in the existing codes. 3) Software design of the next-generation codes needs to take into consideration of having the flexibility to add new models if necessary, as well as to allow for embedded uncertainty quantification, and capability of multi-physics coupling with other codes. 4) The next generation codes need proper verification and validation (V & V) before they can be used to plant applications. New approaches need to be developed to verify and validate complex multi-physics models with multiple time and length scales and advanced modeling techniques. 5) The next generation system analysis codes should be designed to be integrated into probabilistic evaluation to enable a risk-informed safety margin characterization (RISMC) process in order to optimize plant safety and performance by incorporating plant impacts, aging, and degradation processes into the safety analysis. (author)

  6. Perspectives on the development of next generation reactor systems safety analysis codes

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, H., E-mail: Hongbin.Zhang@inl.gov [Idaho National Laboratory, Idaho Falls, ID (United States)

    2015-07-01

    tackle the deficiencies in the existing codes. 3) Software design of the next-generation codes needs to take into consideration of having the flexibility to add new models if necessary, as well as to allow for embedded uncertainty quantification, and capability of multi-physics coupling with other codes. 4) The next generation codes need proper verification and validation (V & V) before they can be used to plant applications. New approaches need to be developed to verify and validate complex multi-physics models with multiple time and length scales and advanced modeling techniques. 5) The next generation system analysis codes should be designed to be integrated into probabilistic evaluation to enable a risk-informed safety margin characterization (RISMC) process in order to optimize plant safety and performance by incorporating plant impacts, aging, and degradation processes into the safety analysis. (author)

  7. The Initial Atmospheric Transport (IAT) Code: Description and Validation

    Energy Technology Data Exchange (ETDEWEB)

    Morrow, Charles W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bartel, Timothy James [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-10-01

    The Initial Atmospheric Transport (IAT) computer code was developed at Sandia National Laboratories as part of their nuclear launch accident consequences analysis suite of computer codes. The purpose of IAT is to predict the initial puff/plume rise resulting from either a solid rocket propellant or liquid rocket fuel fire. The code generates initial conditions for subsequent atmospheric transport calculations. The Initial Atmospheric Transfer (IAT) code has been compared to two data sets which are appropriate to the design space of space launch accident analyses. The primary model uncertainties are the entrainment coefficients for the extended Taylor model. The Titan 34D accident (1986) was used to calibrate these entrainment settings for a prototypic liquid propellant accident while the recent Johns Hopkins University Applied Physics Laboratory (JHU/APL, or simply APL) large propellant block tests (2012) were used to calibrate the entrainment settings for prototypic solid propellant accidents. North American Meteorology (NAM )formatted weather data profiles are used by IAT to determine the local buoyancy force balance. The IAT comparisons for the APL solid propellant tests illustrate the sensitivity of the plume elevation to the weather profiles; that is, the weather profile is a dominant factor in determining the plume elevation. The IAT code performed remarkably well and is considered validated for neutral weather conditions.

  8. Development and assessment of best estimate integrated safety analysis code

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Bub Dong; Lee, Young Jin; Hwang, Moon Kyu (and others)

    2007-03-15

    Improvement of the integrated safety analysis code MARS3.0 has been carried out and a multi-D safety analysis application system has been established. Iterative matrix solver and parallel processing algorithm have been introduced, and a LINUX version has been generated to enable MARS to run in cluster PCs. MARS variables and sub-routines have been reformed and modularised to simplify code maintenance. Model uncertainty analyses have been performed for THTF, FLECHT, NEPTUN, and LOFT experiments as well as APR1400 plant. Participations in international cooperation research projects such as OECD BEMUSE, SETH, PKL, BFBT, and TMI-2 have been actively pursued as part of code assessment efforts. The assessment, evaluation and experimental data obtained through international cooperation projects have been registered and maintained in the T/H Databank. Multi-D analyses of APR1400 LBLOCA, DVI Break, SLB, and SGTR have been carried out as a part of application efforts in multi-D safety analysis. GUI based 3D input generator has been developed for user convenience. Operation of the MARS Users Group (MUG) was continued and through MUG, the technology has been transferred to 24 organisations. A set of 4 volumes of user manuals has been compiled and the correction reports for the code errors reported during MARS development have been published.

  9. Development and assessment of best estimate integrated safety analysis code

    International Nuclear Information System (INIS)

    Chung, Bub Dong; Lee, Young Jin; Hwang, Moon Kyu

    2007-03-01

    Improvement of the integrated safety analysis code MARS3.0 has been carried out and a multi-D safety analysis application system has been established. Iterative matrix solver and parallel processing algorithm have been introduced, and a LINUX version has been generated to enable MARS to run in cluster PCs. MARS variables and sub-routines have been reformed and modularised to simplify code maintenance. Model uncertainty analyses have been performed for THTF, FLECHT, NEPTUN, and LOFT experiments as well as APR1400 plant. Participations in international cooperation research projects such as OECD BEMUSE, SETH, PKL, BFBT, and TMI-2 have been actively pursued as part of code assessment efforts. The assessment, evaluation and experimental data obtained through international cooperation projects have been registered and maintained in the T/H Databank. Multi-D analyses of APR1400 LBLOCA, DVI Break, SLB, and SGTR have been carried out as a part of application efforts in multi-D safety analysis. GUI based 3D input generator has been developed for user convenience. Operation of the MARS Users Group (MUG) was continued and through MUG, the technology has been transferred to 24 organisations. A set of 4 volumes of user manuals has been compiled and the correction reports for the code errors reported during MARS development have been published

  10. Vectorization of the KENO V.a criticality safety code

    International Nuclear Information System (INIS)

    Hollenbach, D.F.; Dodds, H.L.; Petrie, L.M.

    1991-01-01

    The development of the vector processor, which is used in the current generation of supercomputers and is beginning to be used in workstations, provides the potential for dramatic speed-up for codes that are able to process data as vectors. Unfortunately, the stochastic nature of Monte Carlo codes prevents the old scalar version of these codes from taking advantage of the vector processors. New Monte Carlo algorithms that process all the histories undergoing the same event as a batch are required. Recently, new vectorized Monte Carlo codes have been developed that show significant speed-ups when compared to the scalar version of themselves or equivalent codes. This paper discusses the vectorization of an already existing and widely used criticality safety code, KENO V.a All the changes made to KENO V.a are transparent to the user making it possible to upgrade from the standard scalar version of KENO V.a to the vectorized version without learning a new code

  11. Audit of data and code use in the SR-Can safety assessment

    Energy Technology Data Exchange (ETDEWEB)

    Hicks, T.W.; Baldwin, T.D. [Galson Sciences Ltd, 5 Grosvenor House, Melton R oad, Oakham, Rutland LE15 6AX (United Kingdom)

    2008-03-15

    Building on the findings of previous studies on data and code quality assurance (QA) in safety assessments, this report provides a review of data and code QA in the SR-Can safety assessment. The data quality audit aimed to check that the selection and use of data in the SR-Can safety assessment was appropriate, focusing on the data that underpin representations of and assumptions about canister, insert, buffer, and backfill behaviour. The SR-Can Data Report provided the initial focus for examining the traceability and reliability of data used in the safety assessment; the Data Report is one of the series of SR-Can safety assessment reports and, in this review, it was anticipated that it would provide the primary source of data on the canister, insert, buffer, and backfill. However, other safety assessment reports (the SR-Can Main Report, the Initial State Report, the Fuel and Canister Process Report, and the Buffer and Backfill Process Report) were found to provide key information on data used in the safety assessment. The quality audit of codes aimed to check that code use in the SR-Can safety assessment has been justified through a transparent and traceable process of code development and selection. The Model Summary Report provided the focus for reviewing the QA status of the codes used in the safety assessment. As well as highlighting a number of concerns regarding QA aspects of specific data sets, parameter values, and codes used in the SR-Can safety assessment (which are presented in the report), the review has led to several general observations on data and code QA that should be considered by SKB in the development and implementation of a QA system for the SR-Site safety assessment: - The SR-Site safety assessment and associated QA records should include information that demonstrates that a full QA system has been implemented in order to build confidence in the validity of the assessment. - The data and parameter values used directly in the safety

  12. RELAP5-3D code validation for RBMK phenomena

    International Nuclear Information System (INIS)

    Fisher, J.E.

    1999-01-01

    The RELAP5-3D thermal-hydraulic code was assessed against Japanese Safety Experiment Loop (SEL) and Heat Transfer Loop (HTL) tests. These tests were chosen because the phenomena present are applicable to analyses of Russian RBMK reactor designs. The assessment cases included parallel channel flow fluctuation tests at reduced and normal water levels, a channel inlet pipe rupture test, and a high power, density wave oscillation test. The results showed that RELAP5-3D has the capability to adequately represent these RBMK-related phenomena

  13. Design validation of the ITER EC upper launcher according to codes and standards

    Energy Technology Data Exchange (ETDEWEB)

    Spaeh, Peter, E-mail: peter.spaeh@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); Aiello, Gaetano [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); Gagliardi, Mario [Karlsruhe Institute of Technology, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); F4E, Fusion for Energy, Joint Undertaking, Barcelona (Spain); Grossetti, Giovanni; Meier, Andreas; Scherer, Theo; Schreck, Sabine; Strauss, Dirk; Vaccaro, Alessandro [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); Weinhorst, Bastian [Karlsruhe Institute of Technology, Institute for Neutron Physics and Reactor Technology, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany)

    2015-10-15

    Highlights: • A set of applicable codes and standards has been chosen for the ITER EC upper launcher. • For a particular component load combinations, failure modes and stress categorizations have been determined. • The design validation was performed in accordance with the “design by analysis”-approach of the ASME boiler and pressure vessel code section III. - Abstract: The ITER electron cyclotron (EC) upper launcher has passed the CDR (conceptual design review) in 2005 and the PDR (preliminary design review) in 2009 and is in its final design phase now. The final design will be elaborated by the European consortium ECHUL-CA with contributions from several research institutes in Germany, Italy, the Netherlands and Switzerland. Within this consortium KIT is responsible for the design of the structural components (the upper port plug, UPP) and also the design integration of the launcher. As the selection of applicable codes and standards was under discussion for the past decade, the conceptual and the preliminary design of the launcher structure were not elaborated in straight accordance with a particular code but with a variety of well-acknowledged engineering practices. For the final design it is compulsory to validate the design with respect to a typical engineering code in order to be compliant with the ITER quality and nuclear requirements and to get acceptance from the French regulator. This paper presents typical design validation of the closure plate, which is the vacuum and Tritium barrier and thus a safety relevant component of the upper port plug (UPP), performed with the ASME boiler and pressure vessel code. Rationales for choosing this code are given as well as a comparison between different design methods, like the “design by rule” and the “design by analysis” approach. Also the selections of proper load specifications and the identification of potential failure modes are covered. In addition to that stress categorizations, analyses

  14. Design validation of the ITER EC upper launcher according to codes and standards

    International Nuclear Information System (INIS)

    Spaeh, Peter; Aiello, Gaetano; Gagliardi, Mario; Grossetti, Giovanni; Meier, Andreas; Scherer, Theo; Schreck, Sabine; Strauss, Dirk; Vaccaro, Alessandro; Weinhorst, Bastian

    2015-01-01

    Highlights: • A set of applicable codes and standards has been chosen for the ITER EC upper launcher. • For a particular component load combinations, failure modes and stress categorizations have been determined. • The design validation was performed in accordance with the “design by analysis”-approach of the ASME boiler and pressure vessel code section III. - Abstract: The ITER electron cyclotron (EC) upper launcher has passed the CDR (conceptual design review) in 2005 and the PDR (preliminary design review) in 2009 and is in its final design phase now. The final design will be elaborated by the European consortium ECHUL-CA with contributions from several research institutes in Germany, Italy, the Netherlands and Switzerland. Within this consortium KIT is responsible for the design of the structural components (the upper port plug, UPP) and also the design integration of the launcher. As the selection of applicable codes and standards was under discussion for the past decade, the conceptual and the preliminary design of the launcher structure were not elaborated in straight accordance with a particular code but with a variety of well-acknowledged engineering practices. For the final design it is compulsory to validate the design with respect to a typical engineering code in order to be compliant with the ITER quality and nuclear requirements and to get acceptance from the French regulator. This paper presents typical design validation of the closure plate, which is the vacuum and Tritium barrier and thus a safety relevant component of the upper port plug (UPP), performed with the ASME boiler and pressure vessel code. Rationales for choosing this code are given as well as a comparison between different design methods, like the “design by rule” and the “design by analysis” approach. Also the selections of proper load specifications and the identification of potential failure modes are covered. In addition to that stress categorizations, analyses

  15. Validation and testing of the VAM2D computer code

    International Nuclear Information System (INIS)

    Kool, J.B.; Wu, Y.S.

    1991-10-01

    This document describes two modeling studies conducted by HydroGeoLogic, Inc. for the US NRC under contract no. NRC-04089-090, entitled, ''Validation and Testing of the VAM2D Computer Code.'' VAM2D is a two-dimensional, variably saturated flow and transport code, with applications for performance assessment of nuclear waste disposal. The computer code itself is documented in a separate NUREG document (NUREG/CR-5352, 1989). The studies presented in this report involve application of the VAM2D code to two diverse subsurface modeling problems. The first one involves modeling of infiltration and redistribution of water and solutes in an initially dry, heterogeneous field soil. This application involves detailed modeling over a relatively short, 9-month time period. The second problem pertains to the application of VAM2D to the modeling of a waste disposal facility in a fractured clay, over much larger space and time scales and with particular emphasis on the applicability and reliability of using equivalent porous medium approach for simulating flow and transport in fractured geologic media. Reflecting the separate and distinct nature of the two problems studied, this report is organized in two separate parts. 61 refs., 31 figs., 9 tabs

  16. Validation of the ORIGEN-S code for predicting radionuclide inventories in used CANDU Fuel

    International Nuclear Information System (INIS)

    Tait, J.C.; Gauld, I.; Kerr, A.H.

    1994-10-01

    The safety assessment being conducted by AECL Research for the concept of deep geological disposal of used CANDU UO 2 fuel requires the calculation of radionuclide inventories in the fuel to provide source terms for radionuclide release. This report discusses the validation of selected actinide and fission-product inventories calculated using the ORIGEN-S code coupled with the WIMS-AECL lattice code, using data from analytical measurements of radioisotope inventories in Pickering CANDU reactor fuel. The recent processing of new ENDF/B-VI cross-section data has allowed the ORIGEN-S calculations to be performed using the most up-to-date nuclear data available. The results indicate that the code is reliably predicting actinide and the majority of fission-product inventories to within the analytical uncertainty. 38 refs., 4 figs., 5 tabs

  17. Validation of the ORIGEN-S code for predicting radionuclide inventories in used CANDU fuel

    International Nuclear Information System (INIS)

    Tait, J.C.; Gauld, I.; Kerr, A.H.

    1995-01-01

    The safety assessment being conducted by AECL Research for the concept of deep geological disposal of used CANDU UO 2 fuel requires the calculation of radionuclide inventories in the fuel to provide source terms for radionuclide release. This report discusses the validation of selected actinide and fission-product inventories calculated using the ORIGEN-S code coupled with the WIMS-AECL lattice code, using data from analytical measurements of radioisotope inventories in Pickering CANDU reactor fuel. The recent processing of new ENDF/B-VI cross-section data has allowed the ORIGEN-S calculations to be performed using the most up-to-date nuclear data available. The results indicate that the code is reliably predicting actinide and the majority of fission-product inventories to within the analytical uncertainty. ((orig.))

  18. Safety in nuclear power plant siting. A code of practice

    International Nuclear Information System (INIS)

    1978-01-01

    This publication is brought out within the framework of establishing Codes of Practice and Safety Guides for nuclear power plants: NUSS programme. The scope of the document encompasses site and site-plant interaction factors related to operational states and accident conditions. The purpose of the Code is to give criteria and procedures to be applied as appropriate to operational states and accident conditions, including those which could lead to emergency situations. This Code is mainly concerned with severe events of low probability which relate to the siting of nuclear power plants and have to be considered in designing a particular nuclear power plant. Annex: Examples of natural and man-made events relevant for design basis evaluation

  19. Application of software to development of reactor-safety codes

    International Nuclear Information System (INIS)

    Wilburn, N.P.; Niccoli, L.G.

    1980-09-01

    Over the past two-and-a-half decades, the application of new techniques has reduced hardware cost for digital computer systems and increased computational speed by several orders of magnitude. A corresponding cost reduction in business and scientific software development has not occurred. The same situation is seen for software developed to model the thermohydraulic behavior of nuclear systems under hypothetical accident situations. For all cases this is particularly noted when costs over the total software life cycle are considered. A solution to this dilemma for reactor safety code systems has been demonstrated by applying the software engineering techniques which have been developed over the course of the last few years in the aerospace and business communities. These techniques have been applied recently with a great deal of success in four major projects at the Hanford Engineering Development Laboratory (HEDL): 1) a rewrite of a major safety code (MELT); 2) development of a new code system (CONACS) for description of the response of LMFBR containment to hypothetical accidents, and 3) development of two new modules for reactor safety analysis

  20. Sodium fast reactor gaps analysis of computer codes and models for accident analysis and reactor safety.

    Energy Technology Data Exchange (ETDEWEB)

    Carbajo, Juan (Oak Ridge National Laboratory, Oak Ridge, TN); Jeong, Hae-Yong (Korea Atomic Energy Research Institute, Daejeon, Korea); Wigeland, Roald (Idaho National Laboratory, Idaho Falls, ID); Corradini, Michael (University of Wisconsin, Madison, WI); Schmidt, Rodney Cannon; Thomas, Justin (Argonne National Laboratory, Argonne, IL); Wei, Tom (Argonne National Laboratory, Argonne, IL); Sofu, Tanju (Argonne National Laboratory, Argonne, IL); Ludewig, Hans (Brookhaven National Laboratory, Upton, NY); Tobita, Yoshiharu (Japan Atomic Energy Agency, Ibaraki-ken, Japan); Ohshima, Hiroyuki (Japan Atomic Energy Agency, Ibaraki-ken, Japan); Serre, Frederic (Centre d' %C3%94etudes nucl%C3%94eaires de Cadarache %3CU%2B2013%3E CEA, France)

    2011-06-01

    This report summarizes the results of an expert-opinion elicitation activity designed to qualitatively assess the status and capabilities of currently available computer codes and models for accident analysis and reactor safety calculations of advanced sodium fast reactors, and identify important gaps. The twelve-member panel consisted of representatives from five U.S. National Laboratories (SNL, ANL, INL, ORNL, and BNL), the University of Wisconsin, the KAERI, the JAEA, and the CEA. The major portion of this elicitation activity occurred during a two-day meeting held on Aug. 10-11, 2010 at Argonne National Laboratory. There were two primary objectives of this work: (1) Identify computer codes currently available for SFR accident analysis and reactor safety calculations; and (2) Assess the status and capability of current US computer codes to adequately model the required accident scenarios and associated phenomena, and identify important gaps. During the review, panel members identified over 60 computer codes that are currently available in the international community to perform different aspects of SFR safety analysis for various event scenarios and accident categories. A brief description of each of these codes together with references (when available) is provided. An adaptation of the Predictive Capability Maturity Model (PCMM) for computational modeling and simulation is described for use in this work. The panel's assessment of the available US codes is presented in the form of nine tables, organized into groups of three for each of three risk categories considered: anticipated operational occurrences (AOOs), design basis accidents (DBA), and beyond design basis accidents (BDBA). A set of summary conclusions are drawn from the results obtained. At the highest level, the panel judged that current US code capabilities are adequate for licensing given reasonable margins, but expressed concern that US code development activities had stagnated and that the

  1. Development validation and use of computer codes for inelastic analysis

    International Nuclear Information System (INIS)

    Jobson, D.A.

    1983-01-01

    A finite element scheme is a system which provides routines so carry out the operations which are common to all finite element programs. The list of items that can be provided as standard by the finite element scheme is surprisingly large and the list provided by the UNCLE finite element scheme is unusually comprehensive. This presentation covers the following: construction of the program, setting up a finite element mesh, generation of coordinates, incorporating boundary and load conditions. Program validation was done by creep calculations performed using CAUSE code. Program use is illustrated by calculating a typical inelastic analysis problem. This includes computer model of the PFR intermediate heat exchanger

  2. Implementation of probabilistic safety concepts in international codes

    International Nuclear Information System (INIS)

    Borges, J.F.

    1977-01-01

    Recent progress in the implementation of safety concepts in international structure codes is briefly presented. Special attention is paid to the work of the Joint-Committee on Structural Safety. The discussion is centered on some problems such as: safety differentiation, definition and combination of actions, spaces for checking safety and non-linear structural behaviour. When discussing safety differentiation it should be considered that the total probability of failure derives from a theoretical probability of failure and a probability of failure due to error and gross negligence. Optimization of design criteria should take into account both causes of failure. The quantification of reliability implies a probabilistic idealization of all basic variables. Steps taken to obtain an improved definition of different types of actions and rules for their combination are described. Safety checking can be carried out in terms of basic variables, action-effects, or any other suitable variable. However, the advantages and disadvantages of the different types of formulation should be discussed, particularly in the case of non-linear structural behaviour. (orig.) [de

  3. Guide to Using the WIND Toolkit Validation Code

    Energy Technology Data Exchange (ETDEWEB)

    Lieberman-Cribbin, W.; Draxl, C.; Clifton, A.

    2014-12-01

    In response to the U.S. Department of Energy's goal of using 20% wind energy by 2030, the Wind Integration National Dataset (WIND) Toolkit was created to provide information on wind speed, wind direction, temperature, surface air pressure, and air density on more than 126,000 locations across the United States from 2007 to 2013. The numerical weather prediction model output, gridded at 2-km and at a 5-minute resolution, was further converted to detail the wind power production time series of existing and potential wind facility sites. For users of the dataset it is important that the information presented in the WIND Toolkit is accurate and that errors are known, as then corrective steps can be taken. Therefore, we provide validation code written in R that will be made public to provide users with tools to validate data of their own locations. Validation is based on statistical analyses of wind speed, using error metrics such as bias, root-mean-square error, centered root-mean-square error, mean absolute error, and percent error. Plots of diurnal cycles, annual cycles, wind roses, histograms of wind speed, and quantile-quantile plots are created to visualize how well observational data compares to model data. Ideally, validation will confirm beneficial locations to utilize wind energy and encourage regional wind integration studies using the WIND Toolkit.

  4. Modification and validation of the natural heat convection and subcooled void formation models in the code PARET

    International Nuclear Information System (INIS)

    Hainoun, A.; Alhabit, F.; Ghazi, N.

    2008-01-01

    Two new modifications have been included in the current PARET code that is widely applied in the dynamic and safety analysis of research reactors. A new model was implemented for the simulation of void formation in the subcooled boiling regime, the other modification dealt with the implementation of a new approach to improve the prediction of heat transfer coefficient under natural circulation condition. The modified code was successfully validated using adequate single effect tests covering the physical phenomena of interest for both natural circulation and subcooled void formation at low pressure and low heat flux. The validation results indicate significant improvement of the code compared to the default version. Additionally, to simplify the code application an interactive user interface was developed enabling pre and post-processing of the code predictions. (author)

  5. Partial Safety Factors and Target Reliability Level in Danish Structural Codes

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Hansen, J. O.; Nielsen, T. A.

    2001-01-01

    The partial safety factors in the newly revised Danish structural codes have been derived using a reliability-based calibration. The calibrated partial safety factors result in the same average reliability level as in the previous codes, but a much more uniform reliability level has been obtained....... The paper describes the code format, the stochastic models and the resulting optimised partial safety factors....

  6. Development of the Monju core safety analysis numerical models by super-COPD code

    International Nuclear Information System (INIS)

    Yamada, Fumiaki; Minami, Masaki

    2010-12-01

    Japan Atomic Energy Agency constructed a computational model for safety analysis of Monju reactor core to be built into a modularized plant dynamics analysis code Super-COPD code, for the purpose of heat removal capability evaluation at the in total 21 defined transients in the annex to the construction permit application. The applicability of this model to core heat removal capability evaluation has been estimated by back to back result comparisons of the constituent models with conventionally applied codes and by application of the unified model. The numerical model for core safety analysis has been built based on the best estimate model validated by the actually measured plant behavior up to 40% rated power conditions, taking over safety analysis models of conventionally applied COPD and HARHO-IN codes, to be capable of overall calculations of the entire plant with the safety protection and control systems. Among the constituents of the analytical model, neutronic-thermal model, heat transfer and hydraulic models of PHTS, SHTS, and water/steam system are individually verified by comparisons with the conventional calculations. Comparisons are also made with the actually measured plant behavior up to 40% rated power conditions to confirm the calculation adequacy and conservativeness of the input data. The unified analytical model was applied to analyses of in total 8 anomaly events; reactivity insertion, abnormal power distribution, decrease and increase of coolant flow rate in PHTS, SHTS and water/steam systems. The resulting maximum values and temporal variations of the key parameters in safety evaluation; temperatures of fuel, cladding, in core sodium coolant and RV inlet and outlet coolant have negligible discrepancies against the existing analysis result in the annex to the construction permit application, verifying the unified analytical model. These works have enabled analytical evaluation of Monju core heat removal capability by Super-COPD utilizing the

  7. Are industry codes and standards a valid cost containment approach

    International Nuclear Information System (INIS)

    Rowley, C.W.; Simpson, G.T.; Young, R.K.

    1990-01-01

    The nuclear industry has historically concentrated on safety design features for many years, but recently has been shifting to the reliability of the operating systems and components. The Navy has already gone through this transition and has found that Reliability Centered Maintenance (RCM) is an invaluable tool to improve the reliability of components, systems, ships, and classes of ships. There is a close correlation of Navy ships and equipment to commercial nuclear power plants and equipment. The Navy has a central engineering and configuration management organization (Naval Sea Systems Command) for over 500 ships, where as the over 100 commercial nuclear power plants and 52 nuclear utilities represent a fragmented owner/management structure. This paper suggests that the results of the application of RCM in the Navy can be duplicated to a large degree in the commercial nuclear power industry by the development and utilization of nuclear codes and standards

  8. Application of software engineering to development of reactor safety codes

    International Nuclear Information System (INIS)

    Wilburn, N.P.; Niccoli, L.G.

    1981-01-01

    Software Engineering, which is a systematic methodology by which a large scale software development project is partitioned into manageable pieces, has been applied to the development of LMFBR safety codes. The techniques have been applied extensively in the business and aerospace communities and have provided an answer to the drastically increasing cost of developing and maintaining software. The five phases of software engineering (Survey, Analysis, Design, Implementation, and Testing) were applied in turn to development of these codes, along with Walkthroughs (peer review) at each stage. The application of these techniques has resulted in SUPERIOR SOFTWARE which is well documented, thoroughly tested, easy to modify, easier to use and maintain. The development projects have resulted in lower overall cost. (orig.) [de

  9. Validation of coupled neutronic / thermal-hydraulic codes for VVER reactors. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Mittag, S.; Grundmann, U.; Kliem, S.; Kozmenkov, Y.; Rindelhardt, U.; Rohde, U.; Weiss, F.-P.; Langenbuch, S.; Krzykacz-Hausmann, B.; Schmidt, K.-D.; Vanttola, T.; Haemaelaeinen, A.; Kaloinen, E.; Kereszturi, A.; Hegyi, G.; Panka, I.; Hadek, J.; Strmensky, C.; Darilek, P.; Petkov, P.; Stefanova, S.; Kuchin, A.; Khalimonchuk, V.; Hlbocky, P.; Sico, D.; Danilin, S.; Ionov, V.; Nikonov, S.; Powney, D.

    2004-08-01

    thermal-hydraulic feedback effects. Thus, in VALCO work package 3 (WP 3) stand-alone three-dimensional neutron-kinetic codes have been validated. Measurements carried out in an original-size VVER-1000 mock-up (V-1000 facility, Kurchatov Institute Moscow) were used for the validation of the codes DYN3D, HEXTRAN, KIKO3D and BIPR-8, which are chiefly designed for VVER safety calculations. The significant neutron flux tilt measured in the V-1000 core, which is caused only by radial-reflector asymmetries, was successfully modelled. A good agreement between calculated and measured steady-state powers has been achieved, for relative assembly powers and inner-assembly pin power distributions. Calculated effective multiplication factors exceed unity in all cases. (orig.)

  10. Fire-safety engineering and performance-based codes

    DEFF Research Database (Denmark)

    Sørensen, Lars Schiøtt

    project administrators, etc. The book deals with the following topics: • Historical presentation on the subject of fire • Legislation and building project administration • European fire standardization • Passive and active fire protection • Performance-based Codes • Fire-safety Engineering • Fundamental......Fire-safety Engineering is written as a textbook for Engineering students at universities and other institutions of higher education that teach in the area of fire. The book can also be used as a work of reference for consulting engineers, Building product manufacturers, contractors, building...... thermodynamics • Heat exchange during the fire process • Skin burns • Burning rate, energy release rate and design fires • Proposal to Risk-based design fires • Proposal to a Fire scale • Material ignition and flame spread • Fire dynamics in buildings • Combustion products and toxic gases • Smoke inhalation...

  11. Change to CERN Safety Rules: Abolition of Safety Code A7

    CERN Multimedia

    2016-01-01

    As from 3 June 2016 Safety Code A7 “Road traffic at CERN” is abolished.   CERN's current practice to follow French or Swiss road traffic regulations on the corresponding parts of the CERN site will continue to apply. HSE Unit

  12. Validating Virtual Safety Stock Effectiveness through Simulation

    Directory of Open Access Journals (Sweden)

    Maria Elena Nenni

    2013-08-01

    safety stock effectiveness through simulation in an inventory system using a base stock policy with periodic reviews and backorders. This approach can be useful for researchers as well as practitioners who want to model the behaviour of an inventory system under uncertain conditions and verify the opportunity for setting up a virtual safety stock on top of, or instead of, the traditional physical safety stock.

  13. Water evaporation over sump surface in nuclear containment studies: CFD and LP codes validation on TOSQAN tests

    Energy Technology Data Exchange (ETDEWEB)

    Malet, J., E-mail: jeanne.malet@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire (IRSN), PSN-RES/SCA BP 68, 91192 Gif-sur-Yvette (France); Degrees du Lou, O. [Institut de Radioprotection et de Sûreté Nucléaire (IRSN), PSN-RES/SCA BP 68, 91192 Gif-sur-Yvette (France); Arts et Métiers ParisTech, DynFluid Lab. EA92, 151, boulevard de l’Hôpital, 75013 Paris (France); Gelain, T. [Institut de Radioprotection et de Sûreté Nucléaire (IRSN), PSN-RES/SCA BP 68, 91192 Gif-sur-Yvette (France)

    2013-10-15

    Highlights: • Simulations of evaporative TOSQAN sump tests are performed. • These tests are under air–steam gas conditions with addition of He, CO{sub 2} and SF{sub 6}. • ASTEC-CPA LP and TONUS-CFD codes with UDF for sump model are used. • Validation of sump models of both codes show good results. • The code–experiment differences are attributed to turbulent gas mixing modeling. -- Abstract: During the course of a severe accident in a Nuclear Power Plant, water can be collected in the sump containment through steam condensation on walls and spray systems activation. The objective of this paper is to present code validation on evaporative sump tests performed on TOSQAN facility. The ASTEC-CPA code is used as a lumped-parameter code and specific user-defined-functions are developed for the TONUS-CFD code. The seven tests are air–steam tests, as well as tests with other non-condensable gases (He, CO{sub 2} and SF{sub 6}) under steady and transient conditions (two depressurization tests). The results show a good agreement between codes and experiments, indicating a good behavior of the sump models in both codes. The sump model developed as User-Defined Functions (UDF) for TONUS is considered as well validated and is ‘ready-to-use’ for all CFD codes in which such UDF can be added. The remaining discrepancies between codes and experiments are caused by turbulent transport and gas mixing, especially in the presence of non-condensable gases other than air, so that code validation on this important topic for hydrogen safety analysis is still recommended.

  14. Development of a safety analysis code for molten salt reactors

    International Nuclear Information System (INIS)

    Zhang Dalin; Qiu Suizheng; Su Guanghui

    2009-01-01

    The molten salt reactor (MSR) well suited to fulfill the criteria defined by the Generation IV International Forum (GIF) is presently revisited all around the world because of different attractive features of current renewed relevance. The MSRs are characterized by using the fluid-fuel, so that their technologies are fundamentally different from those used in the conventional solid-fuel reactors. In this work, in particular, the attention is focused on the safety characteristic analysis of the MSRs, in which a point kinetic model considering the flow effects of the fuel salt is established for the MSRs and calculated by developing a microcomputer code coupling with a simplified heat transfer model in the core. The founded models and developed code are applied to analyze the safety characteristics of the molten salt actinide recycler and transmuter system (MOSART) by simulating three types of basic transient conditions including the unprotected loss of flow, unprotected overcooling accident and unprotected transient overpower. Some reasonable results are obtained for the MOSART, which show that the MOSART conceptual design is an inherently stable reactor design. The present study provides some valuable information for the research and design of the new generation MSRs.

  15. Optimization and Validation of the Developed Uranium Isotopic Analysis Code

    Energy Technology Data Exchange (ETDEWEB)

    Kim, J. H.; Kang, M. Y.; Kim, Jinhyeong; Choi, H. D. [Seoul National Univ., Seoul (Korea, Republic of)

    2014-10-15

    γ-ray spectroscopy is a representative non-destructive assay for nuclear material, and less time-consuming and less expensive than the destructive analysis method. The destructive technique is more precise than NDA technique, however, there is some correction algorithm which can improve the performance of γ-spectroscopy. For this reason, an analysis code for uranium isotopic analysis is developed by Applied Nuclear Physics Group in Seoul National University. Overlapped γ- and x-ray peaks in the 89-101 keV X{sub α}-region are fitted with Gaussian and Lorentzian distribution peak functions, tail and background functions. In this study, optimizations for the full-energy peak efficiency calibration and fitting parameters of peak tail and background are performed, and validated with 24 hour acquisition of CRM uranium samples. The optimization of peak tail and background parameters are performed with the validation by using CRM uranium samples. The analysis performance is improved in HEU samples, but more optimization of fitting parameters is required in LEU sample analysis. In the future, the optimization research about the fitting parameters with various type of uranium samples will be performed. {sup 234}U isotopic analysis algorithms and correction algorithms (coincidence effect, self-attenuation effect) will be developed.

  16. Phenomenological modeling of critical heat flux: The GRAMP code and its validation

    International Nuclear Information System (INIS)

    Ahmad, M.; Chandraker, D.K.; Hewitt, G.F.; Vijayan, P.K.; Walker, S.P.

    2013-01-01

    Highlights: ► Assessment of CHF limits is vital for LWR optimization and safety analysis. ► Phenomenological modeling is a valuable adjunct to pure empiricism. ► It is based on empirical representations of the (several, competing) phenomena. ► Phenomenological modeling codes making ‘aggregate’ predictions need careful assessment against experiments. ► The physical and mathematical basis of a phenomenological modeling code GRAMP is presented. ► The GRAMP code is assessed against measurements from BARC (India) and Harwell (UK), and the Look Up Tables. - Abstract: Reliable knowledge of the critical heat flux is vital for the design of light water reactors, for both safety and optimization. The use of wholly empirical correlations, or equivalently “Look Up Tables”, can be very effective, but is generally less so in more complex cases, and in particular cases where the heat flux is axially non-uniform. Phenomenological models are in principle more able to take into account of a wider range of conditions, with a less comprehensive coverage of experimental measurements. These models themselves are in part based upon empirical correlations, albeit of the more fundamental individual phenomena occurring, rather than the aggregate behaviour, and as such they too require experimental validation. In this paper we present the basis of a general-purpose phenomenological code, GRAMP, and then use two independent ‘direct’ sets of measurement, from BARC in India and from Harwell in the United Kingdom, and the large dataset embodied in the Look Up Tables, to perform a validation exercise on it. Very good agreement between predictions and experimental measurements is observed, adding to the confidence with which the phenomenological model can be used. Remaining important uncertainties in the phenomenological modeling of CHF, namely the importance of the initial entrained fraction on entry to annular flow, and the influence of the heat flux on entrainment rate

  17. Validation of the TIARA code to tritium inventory data

    International Nuclear Information System (INIS)

    Billone, M.C.

    1994-03-01

    The TIARA code has been developed to predict tritium inventory in Li 2 O breeder ceramic and to predict purge exit flow rate and composition. Inventory predictions are based on models for bulk diffusion, surface desorption, solubility and precipitation. Parameters for these models are determined from the results of laboratory annealing studies on unirradiated and irradiated Li 2 O. Inventory data from in-reactor purge flow tests are used for model improvement, fine-tuning of model parameters and validation. In this current work, the inventory measurement near the purge inlet from the BEATRIX-II thin-ring sample is used to fine tune the surface desorption model parameters for T > 470 degrees C, and the inventory measurement near the midplane from VOM-15H is used to fine tune the moisture solubility model parameters. predictions are then validated to the remaining inventory data from EXOTIC-2 (1 point), SIBELIUS (3 axial points), VOM-15H (2 axial points), CRITIC-1 (4 axial points), BEATRIX-II thin ring (3 axial points) and BEATRIX-II thick pellet (5 radial points). Thus. of the 20 data points, two we re used for fine tuning model parameters and 18 were used for validation. The inventory data span the range of 0.05--1.44 wppm with an average of 0.48 wppm. The data pertain to samples whose end-of-life temperatures were in the range of 490--1000 degrees C. On the average, the TIARA predictions agree quite well with the data (< 0.02 wppm difference). However, the root-mean-square deviation is 0.44 wppm, mostly due to over-predictions for the SIBELIUS samples and the higher-temperature radial samples from the BEATRIX-11 thick-pellet

  18. Section 60 revisited (The Ontario Electrical Safety Code)

    Energy Technology Data Exchange (ETDEWEB)

    Olechna, T.

    2003-06-01

    Recent changes to the Ontario Electrical Safety Code (OESC), specifically the deletion of Section 60, Electrical Communication Systems, are discussed in an effort to explain the history behind the decision and the time frame of the changes. Communication systems include telephone, telegraph, data communications, intercommunications, wired music and paging systems. In brief, the deletion of Section 60 occurred in 1983, and resulted from the fact that communication-type wiring was historically the property of the communications utility and under federal jurisdiction. Since such equipment was under federal jurisdiction, they were not inspected in Ontario, hence the deletion of Section 60 from the Ontario Code. It should be noted that although Section 60 is deleted, a number of rules applicable to communications circuits are spread throughout various sections of the Code, notably in Rule 1-032 dealing with damage and interference, Rule 4-022 involving harmonics issues, Rule 12-904(2) regulates the use of conductors that are of different sources of voltage, and Rule 10-708 which specifies the spacing and bonding requirements for communications systems. The end result is that even though Section 60 was deleted, there are these and other rules in the OESC that have direct impact on communications circuits and in effect help to protect the integrity of the system.

  19. Interface design of VSOP'94 computer code for safety analysis

    International Nuclear Information System (INIS)

    Natsir, Khairina; Andiwijayakusuma, D.; Wahanani, Nursinta Adi; Yazid, Putranto Ilham

    2014-01-01

    Today, most software applications, also in the nuclear field, come with a graphical user interface. VSOP'94 (Very Superior Old Program), was designed to simplify the process of performing reactor simulation. VSOP is a integrated code system to simulate the life history of a nuclear reactor that is devoted in education and research. One advantage of VSOP program is its ability to calculate the neutron spectrum estimation, fuel cycle, 2-D diffusion, resonance integral, estimation of reactors fuel costs, and integrated thermal hydraulics. VSOP also can be used to comparative studies and simulation of reactor safety. However, existing VSOP is a conventional program, which was developed using Fortran 65 and have several problems in using it, for example, it is only operated on Dec Alpha mainframe platforms and provide text-based output, difficult to use, especially in data preparation and interpretation of results. We develop a GUI-VSOP, which is an interface program to facilitate the preparation of data, run the VSOP code and read the results in a more user friendly way and useable on the Personal 'Computer (PC). Modifications include the development of interfaces on preprocessing, processing and postprocessing. GUI-based interface for preprocessing aims to provide a convenience way in preparing data. Processing interface is intended to provide convenience in configuring input files and libraries and do compiling VSOP code. Postprocessing interface designed to visualized the VSOP output in table and graphic forms. GUI-VSOP expected to be useful to simplify and speed up the process and analysis of safety aspects

  20. Interface design of VSOP'94 computer code for safety analysis

    Science.gov (United States)

    Natsir, Khairina; Yazid, Putranto Ilham; Andiwijayakusuma, D.; Wahanani, Nursinta Adi

    2014-09-01

    Today, most software applications, also in the nuclear field, come with a graphical user interface. VSOP'94 (Very Superior Old Program), was designed to simplify the process of performing reactor simulation. VSOP is a integrated code system to simulate the life history of a nuclear reactor that is devoted in education and research. One advantage of VSOP program is its ability to calculate the neutron spectrum estimation, fuel cycle, 2-D diffusion, resonance integral, estimation of reactors fuel costs, and integrated thermal hydraulics. VSOP also can be used to comparative studies and simulation of reactor safety. However, existing VSOP is a conventional program, which was developed using Fortran 65 and have several problems in using it, for example, it is only operated on Dec Alpha mainframe platforms and provide text-based output, difficult to use, especially in data preparation and interpretation of results. We develop a GUI-VSOP, which is an interface program to facilitate the preparation of data, run the VSOP code and read the results in a more user friendly way and useable on the Personal 'Computer (PC). Modifications include the development of interfaces on preprocessing, processing and postprocessing. GUI-based interface for preprocessing aims to provide a convenience way in preparing data. Processing interface is intended to provide convenience in configuring input files and libraries and do compiling VSOP code. Postprocessing interface designed to visualized the VSOP output in table and graphic forms. GUI-VSOP expected to be useful to simplify and speed up the process and analysis of safety aspects.

  1. Validation of CFD models for hydrogen safety application

    International Nuclear Information System (INIS)

    Nikolaeva, Anna; Skibin, Alexander; Krutikov, Alexey; Golibrodo, Luka; Volkov, Vasiliy; Nechaev, Artem; Nadinskiy, Yuriy

    2015-01-01

    Most accidents involving hydrogen begin with its leakage and spreading in the air and spontaneous detonation, which is accompanied by fire or deflagration of hydrogen mixture with heat and /or shocks, which may cause harm to life and equipment. Outflow of hydrogen in a confined volume and its propagation in the volume is the worst option because of the impact of the insularity on the process of detonation. According to the safety requirements for handling hydrogen specialized systems (ventilation, sprinklers, burners etc.) are required for maintaining the hydrogen concentration less than the critical value, to eliminate the possibility of detonation and flame propagation. In this study, a simulation of helium propagation in a confined space with different methods of injection and ventilation of helium is presented, which is used as a safe replacement of hydrogen in experimental studies. Five experiments were simulated in the range from laminar to developed turbulent with different Froude numbers, which determine the regime of the helium outflow in the air. The processes of stratification and erosion of helium stratified layer were investigated. The study includes some results of OECD/NEA-PSI PANDA benchmark and some results of Gamelan project. An analysis of applicability of various turbulence models, which are used to close the system of equations of momentum transport, implemented in the commercial codes STAR CD, STAR CCM+, ANSYS CFX, was conducted for different mesh types (polyhedral and hexahedral). A comparison of computational studies results with experimental data showed a good agreement. In particular, for transition and turbulent regimes the error of the numerical results lies in the range from 5 to 15% for all turbulence models considered. This indicates applicability of the methods considered for some hydrogen safety problems. However, it should be noted that more validation research should be made to use CFD in Hydrogen safety applications with a wide

  2. Safety codes and guides for nuclear power plants

    International Nuclear Information System (INIS)

    Iansiti, E.

    1976-01-01

    The Codes of Practice and Safety Guides that are being developed by the International Atomic Energy Agency are divided in five topical areas: Governmental Organization, Siting, Design, Operation and Quality Assurance. In each area, a scientific secretary is responsible for developing the documents and five Technical Review Committees composed of 10 to 12 experts from various Members Countries revise the drafts at different stages. A Senior Advisory Group supervises the entire programme and revises the document. A scientific co-ordinator is responsible for the co-ordination within the programme with other sections of the IAEA, and with other international organizations. In preparing a document, information on the practice adopted by Member States is collected, a group of experts is convened for preparing a preliminary draft on the basis of this material and the draft is then reviewed by the appropriate Technical Review Committee. The document is translated into various languages, reviewed by the Senior Advisory Group and sent to Member States for comments. After the comments of Member States have been received, the Technical Review Committee and then the Senior Advisory Group are convened again for the final revision of the document. Some 25 drafts, are in different stages of development. The preparation of a document in its final form takes about two years. The programme started in 1975 and to date most of the safety codes and a few safety guides have been sent to Member States for comments. These documents will have gone through the entire development procedure by early 1977. The Senior Advisory Groups and the Technical Review Committees meet on the average four times a year for a week at a time. Until now these meetings have been mainly concerned with the development of new documents or with that part of the procedure which precedes the transmission of the draft to Member States for comments. The next series of meetings will deal with the revisions needed to

  3. Validation of the Thermal-Hydraulic Model in the SACAP Code with the ISP Tests

    Energy Technology Data Exchange (ETDEWEB)

    Park, Soon-Ho; Kim, Dong-Min; Park, Chang-Hwan [FNC Technology Co., Yongin (Korea, Republic of)

    2016-10-15

    In safety viewpoint, the pressure of the containment is the important parameter, of course, the local hydrogen concentration is also the parameter of the major concern because of its flammability and the risk of the detonation. In Korea, there have been an extensive efforts to develop the computer code which can analyze the severe accident behavior of the pressurized water reactor. The development has been done in a modularized manner and SACAP(Severe Accident Containment Analysis Package) code is now under final stage of development. SACAP code adopts LP(Lumped Parameter) model and is applicable to analyze the synthetic behavior of the containment during severe accident occurred by thermal-hydraulic transient, combustible gas burn, direct containment heating by high pressure melt ejection, steam explosion and molten core-concrete interaction. The analyses of a number of ISP(International Standard Problem) experiments were done as a part of the SACAP code V and V(verification and validation). In this paper, the SACAP analysis results for ISP-35 NUPEC and ISP-47 TOSQAN are presented including comparison with other existing NPP simulation codes. In this paper, we selected and analyzed ISP-35 NUPEC, ISP-47 TOSQAN in order to confirm the computational performance of SACAP code currently under development. Now the multi-node analysis for the ISP-47 is under process. As a result of simulation, SACAP predicts well the thermal-hydraulic variables such as temperature, pressure, etc. Also, we verify that SACAP code is properly equipped to analyze the gas distribution and condensation.

  4. COCOSYS: Status of development and validation of the German containment code system

    International Nuclear Information System (INIS)

    Allelein, H.-J.; Arndt, S.; Klein-Hessling, W.; Schwarz, S.; Spengler, C.; Weber, G.

    2006-01-01

    For the simulation of severe accident propagation in containments of nuclear power plants it is necessary to assess the efficiency of a severe accident measures under conditions as realistic as possible. Therefore the German containment code system COCOSYS is under development and validation at GRS. The main objective is to provide a code system on the basis of mostly mechanistic models for the comprehensive simulation of all relevant processes and plant states during severe accidents in the containment of light water reactors covering the design basis accidents, too. COCOSYS is being used for the identification of possible deficits in plant safety, qualification of the safety reserves of the entire system, assessment of damage-limiting or mitigating accident management measures, support of integral codes in PSA level 2 studies and safety evaluation of new plants. COCOSYS is composed for three main modules, which are separate executable files. The communication is realized via PVM (parallel virtual machine). The thermal hydraulic main module (THY) contains several specific models relevant for the simulation of severe accidents. Beside the usual capabilities to calculate the gas distribution and thermal behavior inside the containment, there are special models for the simulation of Hydrogen deflagration, pressure suppression systems etc. Further detailed models exist for the simulation of safety systems, like catalytic recombiners (PAR's), safety relief valves (used in WWR-440/V-230 type plants), ice condenser model, pump and spray system models for the complete simulation of cooling systems. The aerosol and fission product part (AFP) describes the aerosol behavior of nonsoluble and as well as hygroscopic aerosols, iodine chemistry and fission transport. Further the decay process of nuclides is considered using ORIGIN like routines. The corium concrete interaction (CCI) main module is based on an improved version of WECHSL extended by the ChemApp module for the

  5. Improving radiopharmaceutical supply chain safety by implementing bar code technology.

    Science.gov (United States)

    Matanza, David; Hallouard, François; Rioufol, Catherine; Fessi, Hatem; Fraysse, Marc

    2014-11-01

    The aim of this study was to describe and evaluate an approach for improving radiopharmaceutical supply chain safety by implementing bar code technology. We first evaluated the current situation of our radiopharmaceutical supply chain and, by means of the ALARM protocol, analysed two dispensing errors that occurred in our department. Thereafter, we implemented a bar code system to secure selected key stages of the radiopharmaceutical supply chain. Finally, we evaluated the cost of this implementation, from overtime, to overheads, to additional radiation exposure to workers. An analysis of the events that occurred revealed a lack of identification of prepared or dispensed drugs. Moreover, the evaluation of the current radiopharmaceutical supply chain showed that the dispensation and injection steps needed to be further secured. The bar code system was used to reinforce product identification at three selected key stages: at usable stock entry; at preparation-dispensation; and during administration, allowing to check conformity between the labelling of the delivered product (identity and activity) and the prescription. The extra time needed for all these steps had no impact on the number and successful conduct of examinations. The investment cost was reduced (2600 euros for new material and 30 euros a year for additional supplies) because of pre-existing computing equipment. With regard to the radiation exposure to workers there was an insignificant overexposure for hands with this new organization because of the labelling and scanning processes of radiolabelled preparation vials. Implementation of bar code technology is now an essential part of a global securing approach towards optimum patient management.

  6. ClinicalCodes: an online clinical codes repository to improve the validity and reproducibility of research using electronic medical records.

    Science.gov (United States)

    Springate, David A; Kontopantelis, Evangelos; Ashcroft, Darren M; Olier, Ivan; Parisi, Rosa; Chamapiwa, Edmore; Reeves, David

    2014-01-01

    Lists of clinical codes are the foundation for research undertaken using electronic medical records (EMRs). If clinical code lists are not available, reviewers are unable to determine the validity of research, full study replication is impossible, researchers are unable to make effective comparisons between studies, and the construction of new code lists is subject to much duplication of effort. Despite this, the publication of clinical codes is rarely if ever a requirement for obtaining grants, validating protocols, or publishing research. In a representative sample of 450 EMR primary research articles indexed on PubMed, we found that only 19 (5.1%) were accompanied by a full set of published clinical codes and 32 (8.6%) stated that code lists were available on request. To help address these problems, we have built an online repository where researchers using EMRs can upload and download lists of clinical codes. The repository will enable clinical researchers to better validate EMR studies, build on previous code lists and compare disease definitions across studies. It will also assist health informaticians in replicating database studies, tracking changes in disease definitions or clinical coding practice through time and sharing clinical code information across platforms and data sources as research objects.

  7. Validation of computer codes and modelling methods for giving proof of nuclear safety of transport and storage of spent VVER-type nuclear fuels. Pt. 2. Criticality safety during transport and storage of spent VVER fuel elements. Final report; Einschaetzung von Rechenprogrammen und Methoden zum Nachweis der nuklearen Sicherheit bei Transport und Lagerung von WWER-Kernbrennstoffen. T. 2. Kritikalitaetssicherheit bei Transport und Lagerung von WWER-Brennelementen. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Buechse, H.; Langowski, A.; Lein, M.; Nagel, R.; Schmidt, H.; Stammel, M.

    1995-03-15

    The report gives the results of investigations on the validation of computer codes used to prove nuclear safety during transport and storage of spent VVER - fuel of NPP Greifswald and Rheinsberg. Characteristics of typical spent fuel (nuclide concentration, neutron source strength, gamma spectrum, decay heat) - calculated with several codes - and dose rates (e.g. in the surrounding of a loaded spent fuel cask) - based on the different source terms - are presented. Differences and their possible reasons are discussed. The results show that despite the differences in the source terms all relevant health physics requirements are met for all cases of source term. The validation of the criticality code OMEGA was established by calculation of appr. 200 critical experiments of LWR fuel, including VVER fuel rod arrangements. The mean error of the effective multiplication factor k{sub eff} is -0,01 compared to the experiment for this area of applicability. Thus, the OMEGA error of 2% assumed in earlier works has turned out to be sufficiently conservative. (orig.) [Deutsch] Der Bericht enthaelt die Ergebnisse von Untersuchungen zur Validierung von Rechenprogrammen, welche zum Nachweis der nukelaren Sicherheit bei Transport und Lagerung von WWER-Kernbrennstoff der KKW Greifswald und Rheinsberg eingesetzt wurden. Es werden eine Charakteristik des abgebrannten Brennstoffs (Nuklidkonzentrationen, Neutronenquellstaerke, Gammaspektrum, Nachzerfallsleistung) - berechnet mit verschiedenen Programmen - und Ortsdosisleistungen (z.B. in der Umgebung eines Transportbehaelters) - basierend auf den verschiedenen Quelltermen - angegeben. Differenzen und Ursachen werden diskutiert. Die Ergebnisse zeigen, dass trotz der Differenzen in den Quelltermen alle strahlenschutztechnisch relevanten Aussagen unbeeinflusst bleiben. Fuer die Einschaetzung des Gueltigkeitsbereiches des Monte-Carlo-Programms OMEGA wurden ca. 200 kritische Experimente mit LWR-Brennstoff unter besonderer Beruecksichtigung

  8. First experimental validation on the core equilibrium code: HARMONIE

    International Nuclear Information System (INIS)

    Van Dorsselaere, J.; Cozzani, M.; Gnuffi, M.

    1981-08-01

    The code HARMONIE calculates the mechanical equilibrium of a fast reactor. An experimental program of deformation, in air, of groups of subassemblies, was performed on a mock-up, in the Super Phenix 1- geometry. This program included three kinds of tests, all performed without and then with grease: on groups of 2 or 3 rings of subassemblies, subjected to a force acting upon flats or angles; on groups of 35 and 41 subassemblies, subjected to a force acting on the first row, then with 1 or 2 empty cells; and on groups with 1 or 2 bowed subassemblies or 1 enlarged one over flats. A preliminary test on the friction coefficient in air between two pads showed some dependance upon the pad surface condition with a scattering factor of 8. Two basic code hypotheses were validated: the rotation of the subassemblies around their axis was negligible after deformation of the group, and the choice of a mean Maxwell coefficient, between those of 1st and 2nd slope, led to very similar results to experimental. The agreement between tests and HARMONIE calculations was suitable, qualitatively for all the groups and quantitatively for regular groups of 3 rings at most. But the difference increased for larger groups of 35 or 41 subassemblies: friction between pads, neglected by HARMONIE, seems to be the main reason. Other reasons for these differences are: the influence of the loading order on the mock-up, and the initial contacts issued from the gap between foot and diagrid-insert, and from manufacture bowings

  9. 76 FR 77549 - Colorado River Indian Tribes-Amendment to Health & Safety Code, Article 2. Liquor

    Science.gov (United States)

    2011-12-13

    ... Health & Safety Code, Article 2. Liquor AGENCY: Bureau of Indian Affairs, Interior. ACTION: Notice. SUMMARY: This notice publishes the amendment to the Colorado River Tribal Health and Safety Code, Article... Code, Article 2, Liquor by Ordinance No. 10-03 on December 13, 2010. This notice is published in...

  10. Reactor Fuel Isotopics and Code Validation for Nuclear Applications

    Energy Technology Data Exchange (ETDEWEB)

    Francis, Matthew W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Weber, Charles F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pigni, Marco T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gauld, Ian C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-02-01

    Experimentally measured isotopic concentrations of well characterized spent nuclear fuel (SNF) samples have been collected and analyzed by previous researchers. These sets of experimental data have been used extensively to validate the accuracy of depletion code predictions for given sets of burnups, initial enrichments, and varying power histories for different reactor types. The purpose of this report is to present the diversity of data in a concise manner and summarize the current accuracy of depletion modeling. All calculations performed for this report were done using the Oak Ridge Isotope GENeration (ORIGEN) code, an internationally used irradiation and decay code solver within the SCALE comprehensive modeling and simulation code. The diversity of data given in this report includes key actinides, stable fission products, and radioactive fission products. In general, when using the current ENDF/B-VII.0 nuclear data libraries in SCALE, the major actinides are predicted to within 5% of the measured values. Large improvements were seen for several of the curium isotopes when using improved cross section data found in evaluated nuclear data file ENDF/B-VII.0 as compared to ENDF/B-V-based results. The impact of the flux spectrum on the plutonium isotope concentrations as a function of burnup was also shown. The general accuracy noted for the actinide samples for reactor types with burnups greater than 5,000 MWd/MTU was not observed for the low-burnup Hanford B samples. More work is needed in understanding these large discrepancies. The stable neodymium and samarium isotopes were predicted to within a few percent of the measured values. Large improvements were seen in prediction for a few of the samarium isotopes when using the ENDF/B-VII.0 libraries compared to results obtained with ENDF/B-V libraries. Very accurate predictions were obtained for 133Cs and 153Eu. However, the predicted values for the stable ruthenium and rhodium isotopes varied

  11. Analytical validation of the CACECO containment analysis code

    International Nuclear Information System (INIS)

    Peak, R.D.

    1979-08-01

    The CACECO containment analysis code was developed to predict the thermodynamic responses of LMFBR containment facilities to a variety of accidents. This report covers the verification of the CACECO code by problems that can be solved by hand calculations or by reference to textbook and literature examples. The verification concentrates on the accuracy of the material and energy balances maintained by the code and on the independence of the four cells analyzed by the code so that the user can be assured that the code analyses are numerically correct and independent of the organization of the input data submitted to the code

  12. Electrical safety code manual a plan language guide to national electrical code, OSHA and NFPA 70E

    CERN Document Server

    Keller, Kimberley

    2010-01-01

    Safety in any workplace is extremely important. In the case of the electrical industry, safety is critical and the codes and regulations which determine safe practices are both diverse and complicated. Employers, electricians, electrical system designers, inspectors, engineers and architects must comply with safety standards listed in the National Electrical Code, OSHA and NFPA 70E. Unfortunately, the publications which list these safety requirements are written in very technically advanced terms and the average person has an extremely difficult time understanding exactly what they need to

  13. Safety analysis of MOX fuels by fuel performance code

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Motoe [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2002-12-01

    Performance of plutonium rick mixed oxide fuels specified for the Reduced-Moderation Water Reactor (RMWR) has been analysed by modified fuel performance code. Thermodynamic properties of these fuels up to 120 GWd/t burnup have not been measured and estimated using existing uranium fuel models. Fission product release, pressure rise inside fuel rods and mechanical loads of fuel cans due to internal pressure have been preliminarily assessed based on assumed axial power distribution history, which show the integrity of fuel performance. Detailed evaluation of fuel-cladding interactions due to thermal expansion or swelling of fuel pellets due to high burnup will be required for safety analysis of mixed oxide fuels. Thermal conductivity and swelling of plutonium rich mixed oxide fuels shall be taken into consideration. (T. Tanaka)

  14. Improved Flow Modeling in Transient Reactor Safety Analysis Computer Codes

    International Nuclear Information System (INIS)

    Holowach, M.J.; Hochreiter, L.E.; Cheung, F.B.

    2002-01-01

    A method of accounting for fluid-to-fluid shear in between calculational cells over a wide range of flow conditions envisioned in reactor safety studies has been developed such that it may be easily implemented into a computer code such as COBRA-TF for more detailed subchannel analysis. At a given nodal height in the calculational model, equivalent hydraulic diameters are determined for each specific calculational cell using either laminar or turbulent velocity profiles. The velocity profile may be determined from a separate CFD (Computational Fluid Dynamics) analysis, experimental data, or existing semi-empirical relationships. The equivalent hydraulic diameter is then applied to the wall drag force calculation so as to determine the appropriate equivalent fluid-to-fluid shear caused by the wall for each cell based on the input velocity profile. This means of assigning the shear to a specific cell is independent of the actual wetted perimeter and flow area for the calculational cell. The use of this equivalent hydraulic diameter for each cell within a calculational subchannel results in a representative velocity profile which can further increase the accuracy and detail of heat transfer and fluid flow modeling within the subchannel when utilizing a thermal hydraulics systems analysis computer code such as COBRA-TF. Utilizing COBRA-TF with the flow modeling enhancement results in increased accuracy for a coarse-mesh model without the significantly greater computational and time requirements of a full-scale 3D (three-dimensional) transient CFD calculation. (authors)

  15. Kayenta Township Building & Safety Department, Tribal Green Building Code Summit Presentation

    Science.gov (United States)

    Tribal Green Building Code Summit Presentation by Kayenta Township Building & Safety Department showing how they established the building department, developed a code adoption and enforcement process, and hired staff to carry out the work.

  16. Method of accounting for code safety valve setpoint drift in safety analyses

    International Nuclear Information System (INIS)

    Rousseau, K.R.; Bergeron, P.A.

    1989-01-01

    In performing the safety analyses for transients that result in a challenge to the reactor coolant system (RCS) pressure boundary, the general acceptance criterion is that the peak RCS pressure not exceed the American Society of Mechanical Engineers limit of 110% of the design pressure. Without crediting non-safety-grade pressure mitigating systems, protection from this limit is mainly provided by the primary and secondary code safety valves. In theory, the combination of relief capacity and setpoints for these valves is designed to provide this protection. Generally, banks of valves are set at varying setpoints staggered by 15- to 20-psid increments to minimize the number of valves that would open by an overpressure challenge. In practice, however, when these valves are removed and tested (typically during a refueling outage), setpoints are sometimes found to have drifted by >50 psid. This drift should be accounted for during the performance of the safety analysis. This paper describes analyses performed by Yankee Atomic Electric Company (YAEC) to account for setpoint drift in safety valves from testing. The results of these analyses are used to define safety valve operability or acceptance criteria

  17. Validation of computer code TRAFIC used for estimation of charcoal heatup in containment ventilation systems

    International Nuclear Information System (INIS)

    Yadav, D.H.; Datta, D.; Malhotra, P.K.; Ghadge, S.G.; Bajaj, S.S.

    2005-01-01

    Full text of publication follows: Standard Indian PHWRs are provided with a Primary Containment Filtration and Pump-Back System (PCFPB) incorporating charcoal filters in the ventilation circuit to remove radioactive iodine that may be released from reactor core into the containment during LOCA+ECCS failure which is a Design Basis Accident for containment of radioactive release. This system is provided with two identical air circulation loops, each having 2 full capacity fans (1 operating and 1 standby) for a bank of four combined charcoal and High Efficiency Particulate Activity (HEPA) filters, in addition to other filters. While the filtration circuit is designed to operate under forced flow conditions, it is of interest to understand the performance of the charcoal filters, in the event of failure of the fans after operating for some time, i.e., when radio-iodine inventory is at its peak value. It is of interest to check whether the buoyancy driven natural circulation occurring in the filtration circuit is sufficient enough to keep the temperature in the charcoal under safe limits. A computer code TRAFIC (Transient Analysis of Filters in Containment) was developed using conservative one dimensional model to analyze the system. Suitable parametric studies were carried out to understand the problem and to identify the safety of existing system. TRAFIC Code has two important components. The first one estimates the heat generation in charcoal filter based on 'Source Term'; while the other one performs thermal-hydraulic computations. In an attempt validate the Code, experimental studies have been carried out. For this purpose, an experimental set up comprising of scaled down model of filtration circuit with heating coils embedded in charcoal for simulating the heating effect due to radio iodine has been constructed. The present work of validation consists of utilizing the results obtained from experiments conducted for different heat loads, elevations and adsorbent

  18. Indications for spine surgery: validation of an administrative coding algorithm to classify degenerative diagnoses

    Science.gov (United States)

    Lurie, Jon D.; Tosteson, Anna N.A.; Deyo, Richard A.; Tosteson, Tor; Weinstein, James; Mirza, Sohail K.

    2014-01-01

    Study Design Retrospective analysis of Medicare claims linked to a multi-center clinical trial. Objective The Spine Patient Outcomes Research Trial (SPORT) provided a unique opportunity to examine the validity of a claims-based algorithm for grouping patients by surgical indication. SPORT enrolled patients for lumbar disc herniation, spinal stenosis, and degenerative spondylolisthesis. We compared the surgical indication derived from Medicare claims to that provided by SPORT surgeons, the “gold standard”. Summary of Background Data Administrative data are frequently used to report procedure rates, surgical safety outcomes, and costs in the management of spinal surgery. However, the accuracy of using diagnosis codes to classify patients by surgical indication has not been examined. Methods Medicare claims were link to beneficiaries enrolled in SPORT. The sensitivity and specificity of three claims-based approaches to group patients based on surgical indications were examined: 1) using the first listed diagnosis; 2) using all diagnoses independently; and 3) using a diagnosis hierarchy based on the support for fusion surgery. Results Medicare claims were obtained from 376 SPORT participants, including 21 with disc herniation, 183 with spinal stenosis, and 172 with degenerative spondylolisthesis. The hierarchical coding algorithm was the most accurate approach for classifying patients by surgical indication, with sensitivities of 76.2%, 88.1%, and 84.3% for disc herniation, spinal stenosis, and degenerative spondylolisthesis cohorts, respectively. The specificity was 98.3% for disc herniation, 83.2% for spinal stenosis, and 90.7% for degenerative spondylolisthesis. Misclassifications were primarily due to codes attributing more complex pathology to the case. Conclusion Standardized approaches for using claims data to accurately group patients by surgical indications has widespread interest. We found that a hierarchical coding approach correctly classified over 90

  19. Development and initial validation of an Aviation Safety Climate Scale.

    Science.gov (United States)

    Evans, Bronwyn; Glendon, A Ian; Creed, Peter A

    2007-01-01

    A need was identified for a consistent set of safety climate factors to provide a basis for aviation industry benchmarking. Six broad safety climate themes were identified from the literature and consultations with industry safety experts. Items representing each of the themes were prepared and administered to 940 Australian commercial pilots. Data from half of the sample (N=468) were used in an exploratory factor analysis that produced a 3-factor model of Management commitment and communication, Safety training and equipment, and Maintenance. A confirmatory factor analysis on the remaining half of the sample showed the 3-factor model to be an adequate fit to the data. The results of this study have produced a scale of safety climate for aviation that is both reliable and valid. This study developed a tool to assess the level of perceived safety climate, specifically of pilots, but may also, with minor modifications, be used to assess other groups' perceptions of safety climate.

  20. Application of best estimate thermalhydraulic codes for the safety analysis of research reactors

    International Nuclear Information System (INIS)

    Adorni, M.; Bousbia-salah, A.; D'Auria, F.; Hamidouche, T.

    2006-01-01

    An established international expertise in relation to computational tools, procedures for their application including Best Estimate (BE) methods supported by uncertainty evaluation, and comprehensive experimental database exists within the safety technology of Nuclear Power Plant (NPP). The importance of transferring NPP safety technology tools and methods to RR safety technology has been noted in recent IAEA activities. However, the ranges of parameters of interest to RR are different from those for NPP: this is namely true for fuel composition, system pressure, adopted materials and overall system geometric configuration. The large variety of research reactors prevented so far the achievement of systematic and detailed lists of initiating events based upon qualified Probabilistic Safety Assessment (PSA) studies with results endorsed by the international community. However, bounding and generalized lists of events are available from IAEA documents and can be considered for deeper studies in the area. In the area of acceptance criteria, established standards accepted by the international community are available. Therefore no major effort is needed, but an effort appears worthwhile to check that those standards are adopted and that the related thresholds are fulfilled. The importance of suitable experimental assessment is recognized. A large amount of data exists as the kinetic dynamic core behaviour form SPERT reactors tests. However, not all data are accessible to all institutions and the relationship between the range of parameters of experiments and the range of parameters relevant to RR technology is not always established. However, code-assessment through relevant set of experimental data are recorded and properly stored. An established technology exists for development, qualification and application of system thermal-hydraulics codes suitable to be adopted for accident analysis in research reactors. This derives from NPP technology. The applicability of

  1. Nuclear Energy Advanced Modeling and Simulation Waste Integrated Performance and Safety Codes (NEAMS Waste IPSC).

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, Peter Andrew

    2011-12-01

    The objective of the U.S. Department of Energy Office of Nuclear Energy Advanced Modeling and Simulation Waste Integrated Performance and Safety Codes (NEAMS Waste IPSC) is to provide an integrated suite of computational modeling and simulation (M&S) capabilities to quantitatively assess the long-term performance of waste forms in the engineered and geologic environments of a radioactive-waste storage facility or disposal repository. Achieving the objective of modeling the performance of a disposal scenario requires describing processes involved in waste form degradation and radionuclide release at the subcontinuum scale, beginning with mechanistic descriptions of chemical reactions and chemical kinetics at the atomic scale, and upscaling into effective, validated constitutive models for input to high-fidelity continuum scale codes for coupled multiphysics simulations of release and transport. Verification and validation (V&V) is required throughout the system to establish evidence-based metrics for the level of confidence in M&S codes and capabilities, including at the subcontiunuum scale and the constitutive models they inform or generate. This Report outlines the nature of the V&V challenge at the subcontinuum scale, an approach to incorporate V&V concepts into subcontinuum scale modeling and simulation (M&S), and a plan to incrementally incorporate effective V&V into subcontinuum scale M&S destined for use in the NEAMS Waste IPSC work flow to meet requirements of quantitative confidence in the constitutive models informed by subcontinuum scale phenomena.

  2. Nuclear Energy Advanced Modeling and Simulation Waste Integrated Performance and Safety Codes (NEAMS Waste IPSC)

    International Nuclear Information System (INIS)

    Schultz, Peter Andrew

    2011-01-01

    The objective of the U.S. Department of Energy Office of Nuclear Energy Advanced Modeling and Simulation Waste Integrated Performance and Safety Codes (NEAMS Waste IPSC) is to provide an integrated suite of computational modeling and simulation (M and S) capabilities to quantitatively assess the long-term performance of waste forms in the engineered and geologic environments of a radioactive-waste storage facility or disposal repository. Achieving the objective of modeling the performance of a disposal scenario requires describing processes involved in waste form degradation and radionuclide release at the subcontinuum scale, beginning with mechanistic descriptions of chemical reactions and chemical kinetics at the atomic scale, and upscaling into effective, validated constitutive models for input to high-fidelity continuum scale codes for coupled multiphysics simulations of release and transport. Verification and validation (V and V) is required throughout the system to establish evidence-based metrics for the level of confidence in M and S codes and capabilities, including at the subcontiunuum scale and the constitutive models they inform or generate. This Report outlines the nature of the V and V challenge at the subcontinuum scale, an approach to incorporate V and V concepts into subcontinuum scale modeling and simulation (M and S), and a plan to incrementally incorporate effective V and V into subcontinuum scale M and S destined for use in the NEAMS Waste IPSC work flow to meet requirements of quantitative confidence in the constitutive models informed by subcontinuum scale phenomena.

  3. Validation of the DRAGON/DONJON code package for MNR using the IAEA 10 MW benchmark problem

    International Nuclear Information System (INIS)

    Day, S.E.; Garland, W.J.

    2000-01-01

    The first step in developing a framework for reactor physics analysis is to establish the appropriate and proven reactor physics codes. The chosen code package is tested, by executing a benchmark problem and comparing the results to the accepted standards. The IAEA 10 MW Benchmark problem is suitable for static reactor physics calculations on plate-fueled research reactor systems and has been used previously to validate codes for the McMaster Nuclear (MNR). The flexible and advanced geometry capabilities of the DRAGON transport theory code make it a desirable tool, and the accompanying DONJON diffusion theory code also has useful features applicable to safety analysis work at MNR. This paper describes the methodology used to benchmark the DRAGON/DONJON code package against this problem and the results herein extend the domain of validation of this code package. The results are directly applicable to MNR and are relevant to a reduced-enrichment fuel program. The DRAGON transport code models, used in this study, are based on the 1-D infinite slab approximation whereas the DONJON diffusion code models are defined in 3-D Cartesian geometry. The cores under consideration are composed of HEU (93% enrichment), MEU (45% enrichment) and LEU (20% enrichment) fuel and are examined in a fresh state, as well as at beginning-of-life (BOL) and end-of-life (EOL) exposures. The required flux plots and flux-ratio plots are included, as are transport theory code k∞and diffusion theory code k eff results. In addition to this, selected isotope atom densities are charted as a function of fuel burnup. Results from this analysis are compared to and are in good agreement with previously published results. (author)

  4. Validation analysis of pool fire experiment (Run-F7) using SPHINCS code

    International Nuclear Information System (INIS)

    Yamaguchi, Akira; Tajima, Yuji

    1998-04-01

    SPHINCS (Sodium Fire Phenomenology IN multi-Cell System) code has been developed for the safety analysis of sodium fire accident in a Fast Breeder Reactor. The main features of the SPHINCS code with respect to the sodium pool fire phenomena are multi-dimensional modeling of the thermal behavior in sodium pool and steel liner, modeling of the extension of sodium pool area based on the sodium mass conservation, and equilibrium model for the chemical reaction of pool fire on the flame sheet at the surface of sodium pool during. Therefore, the SPHINCS code is capable of temperature evaluation of the steel liner in detail during the small and/or medium scale sodium leakage accidents. In this study, Run-F7 experiment in which the sodium leakage rate is 11.8 kg/hour has been analyzed. In the experiment the diameter of the sodium pool is approximately 60 cm and the maximum steel liner temperature was 616 degree C. The analytical results tell us the agreement between the SPHINCS analysis and the experiment is excellent with respect to the time history and spatial distribution of the liner temperature, sodium pool extension behavior, as well as atmosphere gas temperature. It is concluded that the pool fire modeling of the SPHINCS code has been validated for this experiment. The SPHINCS code is currently applicable to the sodium pool fire phenomena and the temperature evaluation of the steel liner. The experiment series are continued to check some parameters, i.e., sodium leakage rate and the height of sodium leakage. Thus, the author will analyze the subsequent experiments to check the influence of the parameters and applies SPHINCS to the sodium fire consequence analysis of fast reactor. (author)

  5. Decay heat experiment and validation of calculation code systems for fusion reactor

    International Nuclear Information System (INIS)

    Maekawa, Fujio; Ikeda, Yujiro; Wada, Masayuki

    1999-10-01

    Although accurate estimation of decay heat value is essential for safety analyses of fusion reactors against loss of coolant accidents and so on, no experimental work has been devoted to validating the estimation. Hence, a decay heat measurement experiment was performed as a task (T-339) of ITER/EDA. A new detector, the Whole Energy Absorption Spectrometer (WEAS), was developed for accurate and efficient measurements of decay heat. Decay heat produced in the thirty-two sample materials which were irradiated by 14-MeV neutrons at FNS/JAERI were measured with WEAS for a wide cooling time period from 1 min to 400 days. The data presently obtained were the first experimental decay heat data in the field of fusion. Validity of decay heat calculation codes of ACT4 and CINAC-V4, activation cross section libraries of FENDL/A-2.0 and JENDL Activation File, and decay data was investigated through analyses of the experiment. As a result, several points that should be modified were found in the codes and data. After solving the problems, it was demonstrated that decay heat valued calculated for most of samples were in good agreement with the experimental data. Especially for stainless steel 316 and copper, which were important materials for ITER, decay heat could be predicted with accuracy of ±10%. (author)

  6. Decay heat experiment and validation of calculation code systems for fusion reactor

    Energy Technology Data Exchange (ETDEWEB)

    Maekawa, Fujio; Ikeda, Yujiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Wada, Masayuki

    1999-10-01

    Although accurate estimation of decay heat value is essential for safety analyses of fusion reactors against loss of coolant accidents and so on, no experimental work has been devoted to validating the estimation. Hence, a decay heat measurement experiment was performed as a task (T-339) of ITER/EDA. A new detector, the Whole Energy Absorption Spectrometer (WEAS), was developed for accurate and efficient measurements of decay heat. Decay heat produced in the thirty-two sample materials which were irradiated by 14-MeV neutrons at FNS/JAERI were measured with WEAS for a wide cooling time period from 1 min to 400 days. The data presently obtained were the first experimental decay heat data in the field of fusion. Validity of decay heat calculation codes of ACT4 and CINAC-V4, activation cross section libraries of FENDL/A-2.0 and JENDL Activation File, and decay data was investigated through analyses of the experiment. As a result, several points that should be modified were found in the codes and data. After solving the problems, it was demonstrated that decay heat valued calculated for most of samples were in good agreement with the experimental data. Especially for stainless steel 316 and copper, which were important materials for ITER, decay heat could be predicted with accuracy of {+-}10%. (author)

  7. Elaboration and Validation of the Medication Prescription Safety Checklist 1

    Science.gov (United States)

    Pires, Aline de Oliveira Meireles; Ferreira, Maria Beatriz Guimarães; do Nascimento, Kleiton Gonçalves; Felix, Márcia Marques dos Santos; Pires, Patrícia da Silva; Barbosa, Maria Helena

    2017-01-01

    ABSTRACT Objective: to elaborate and validate a checklist to identify compliance with the recommendations for the structure of medication prescriptions, based on the Protocol of the Ministry of Health and the Brazilian Health Surveillance Agency. Method: methodological research, conducted through the validation and reliability analysis process, using a sample of 27 electronic prescriptions. Results: the analyses confirmed the content validity and reliability of the tool. The content validity, obtained by expert assessment, was considered satisfactory as it covered items that represent the compliance with the recommendations regarding the structure of the medication prescriptions. The reliability, assessed through interrater agreement, was excellent (ICC=1.00) and showed perfect agreement (K=1.00). Conclusion: the Medication Prescription Safety Checklist showed to be a valid and reliable tool for the group studied. We hope that this study can contribute to the prevention of adverse events, as well as to the improvement of care quality and safety in medication use. PMID:28793128

  8. Compendium of computer codes for the safety analysis of fast breeder reactors

    International Nuclear Information System (INIS)

    1977-10-01

    The objective of the compendium is to provide the reader with a guide which briefly describes many of the computer codes used for liquid metal fast breeder reactor safety analyses, since it is for this system that most of the codes have been developed. The compendium is designed to address the following frequently asked questions from individuals in licensing and research and development activities: (1) What does the code do. (2) To what safety problems has it been applied. (3) What are the code's limitations. (4) What is being done to remove these limitations. (5) How does the code compare with experimental observations and other code predictions. (6) What reference documents are available

  9. Development and validation of a criticality calculation scheme based on French deterministic transport codes

    International Nuclear Information System (INIS)

    Santamarina, A.

    1991-01-01

    A criticality-safety calculational scheme using the automated deterministic code system, APOLLO-BISTRO, has been developed. The cell/assembly code APOLLO is used mainly in LWR and HCR design calculations, and its validation spans a wide range of moderation ratios, including voided configurations. Its recent 99-group library and self-shielded cross-sections has been extensively qualified through critical experiments and PWR spent fuel analysis. The PIC self-shielding formalism enables a rigorous treatment of the fuel double heterogeneity in dissolver medium calculations. BISTRO is an optimized multidimensional SN code, part of the modular CCRR package used mainly in FBR calculations. The APOLLO-BISTRO scheme was applied to the 18 experimental benchmarks selected by the OECD/NEACRP Criticality Calculation Working Group. The Calculation-Experiment discrepancy was within ± 1% in ΔK/K and always looked consistent with the experimental uncertainty margin. In the critical experiments corresponding to a dissolver type benchmark, our tools computed a satisfactory Keff. In the VALDUC fuel storage experiments, with hafnium plates, the computed Keff ranged between 0.994 and 1.003 for the various watergaps spacing the fuel clusters from the absorber plates. The APOLLO-KENOEUR statistic calculational scheme, based on the same self-shielded multigroup library, supplied consistent results within 0.3% in ΔK/K. (Author)

  10. Validation of CATHARE 3D code against UPTF TRAM C3 transients

    International Nuclear Information System (INIS)

    Glantz, Tony; Freitas, Roberto

    2007-01-01

    Within the nuclear reactor safety analysis, one of the events that could potentially lead to a recriticality accident in case of a Small Break LOCA (SBLOCA) in a pressurized water reactor (PWR) is a boron dilution scenario followed by a coolant mixing transient. Some UPTF experiments can be interpreted as generic boron dilution experiments. In fact, the UPTF experiments were originally designed to conduct separate effects studies focused on multi-dimensional thermal hydraulic phenomena. But, in the case of experimental program TRAM, some studies are realized on the boron mixing: tests C3. Some of these tests have been used for the validation and assessment of the 3D module of CATHARE code. Results are very satisfying; CATHARE 3D code is able to reproduce correctly the main features of the UPTF TRAM C3 tests, the temperature mixing in the cold leg, the formation of a strong stratification in the upper downcomer, the perfect mixing temperature in the lower downcomer and the strong stratification in the lower plenum. These results are also compared with the CFX-5 and TRIO-U codes results on these tests. (author)

  11. ESE a 2D compressible multiphase flow code developed for MFCI analysis - code validation

    International Nuclear Information System (INIS)

    Leskovar, M.; Mavko, B.

    1998-01-01

    ESE (Evaluation of Steam Explosions) is a general second order accurate two-dimensional compressible multiphase flow computer code. It has been developed to model the interaction of molten core debris with water during the first premixing stage of a steam explosion. A steam explosion is a physical event, which may occur during a severe reactor accident following core meltdown when the molten fuel comes into contact with the coolant water. Since the exchanges of mass, momentum and energy are regime dependent, different exchange laws have been incorporated in ESE for the major flow regimes. With ESE a number of premixing experiments performed at the Oxford University and at the QUEOS facility at Forschungszentrum Karlsruhe has been simulated. In these premixing experiments different jets of spheres were injected in a water poll. The ESE validation plan was carefully chosen, starting from very simple, well-defined problems, and gradually working up to more complicated ones. The results of ESE simulations, which were compared to experimental data and also to first order accurate calculations, are presented in form graphs. Most of the ESE results agree qualitatively as quantitatively reasonably well with experimental data and in general better than the results obtained with the first order accurate calculation.(author)

  12. Use of operational data for the validation of the SOPHT thermal-hydraulic code

    Energy Technology Data Exchange (ETDEWEB)

    Ho, S F; Martin, G; Shoukas, L; Siddiqui, Z; Phillips, B [Ontario Hydro, Bowmanville, ON (Canada). Darlington Nuclear Generating Station

    1996-12-31

    The primary objective of this paper is to describe the validation process of the SOPHT and MINI-SOPHT codes with the use of reactor operational data. The secondary objective is to illustrative the effectiveness of the code as a performance monitoring tool by discussing the discoveries that were made during the validation process. (author). 2 refs.

  13. International integral experiments databases in support of nuclear data and code validation

    International Nuclear Information System (INIS)

    Briggs, J. Blair; Gado, Janos; Hunter, Hamilton; Kodeli, Ivan; Salvatores, Massimo; Sartori, Enrico

    2002-01-01

    The OECD/NEA Nuclear Science Committee (NSC) has identified the need to establish international databases containing all the important experiments that are available for sharing among the specialists. The NSC has set up or sponsored specific activities to achieve this. The aim is to preserve them in an agreed standard format in computer accessible form, to use them for international activities involving validation of current and new calculational schemes including computer codes and nuclear data libraries, for assessing uncertainties, confidence bounds and safety margins, and to record measurement methods and techniques. The databases so far established or in preparation related to nuclear data validation cover the following areas: SINBAD - A Radiation Shielding Experiments database encompassing reactor shielding, fusion blanket neutronics, and accelerator shielding. ICSBEP - International Criticality Safety Benchmark Experiments Project Handbook, with more than 2500 critical configurations with different combination of materials and spectral indices. IRPhEP - International Reactor Physics Experimental Benchmarks Evaluation Project. The different projects are described in the following including results achieved, work in progress and planned. (author)

  14. Sensitivity and uncertainty analyses applied to criticality safety validation. Volume 2

    International Nuclear Information System (INIS)

    Broadhead, B.L.; Hopper, C.M.; Parks, C.V.

    1999-01-01

    This report presents the application of sensitivity and uncertainty (S/U) analysis methodologies developed in Volume 1 to the code/data validation tasks of a criticality safety computational study. Sensitivity and uncertainty analysis methods were first developed for application to fast reactor studies in the 1970s. This work has revitalized and updated the existing S/U computational capabilities such that they can be used as prototypic modules of the SCALE code system, which contains criticality analysis tools currently in use by criticality safety practitioners. After complete development, simplified tools are expected to be released for general use. The methods for application of S/U and generalized linear-least-square methodology (GLLSM) tools to the criticality safety validation procedures were described in Volume 1 of this report. Volume 2 of this report presents the application of these procedures to the validation of criticality safety analyses supporting uranium operations where enrichments are greater than 5 wt %. Specifically, the traditional k eff trending analyses are compared with newly developed k eff trending procedures, utilizing the D and c k coefficients described in Volume 1. These newly developed procedures are applied to a family of postulated systems involving U(11)O 2 fuel, with H/X values ranging from 0--1,000. These analyses produced a series of guidance and recommendations for the general usage of these various techniques. Recommendations for future work are also detailed

  15. Thermal-hydraulic code for estimating safety limits of nuclear reactors with plate type fuels

    Energy Technology Data Exchange (ETDEWEB)

    Castellanos, Duvan A.; Moreira, João L.; Maiorino, Jose R.; Rossi, Pedro R.; Carajilescov, Pedro, E-mail: duvan.castellanos@ufabc.edu.br, E-mail: joao.moreira@ufabc.edu.br, E-mail: joserubens.maiorino@ufabc.edu.br, E-mail: pedro.rossi@ufabc.edu.br, E-mail: pedro.carajilescov10@gmail.com [Universidade Federal do ABC (UFABC), Santo André, SP (Brazil). Centro de Engenharias, Modelagem e Ciências Sociais Aplicadas

    2017-07-01

    To ensure the normal and safe operation of PWR type nuclear reactors is necessary the knowledge of nuclear and heat transfer properties of the fuel, coolant and structural materials. The thermal-hydraulic analysis of nuclear reactors yields parameters such as the distribution of fuel and coolant temperatures, and the departure from nucleated boiling ratio. Usually computational codes are used to analyze the safety performance of the core. This research work presents a computer code for performing thermal-hydraulic analyses of nuclear reactors with plate-type fuel elements operating at low pressure and temperature (research reactors) or high temperature and pressure (naval propulsion or small power reactors). The code uses the sub-channel method based on geometric and thermal-hydraulic conditions. In order to solve the conservation equations for mass, momentum and energy, each sub-channel is divided into control volumes in the axial direction. The mass flow distribution for each fuel element of core is obtained. Analysis of critical heat flux is performed in the hottest channel. The code considers the radial symmetry and the chain or cascade method for two steps in order to facilitate the whole analysis. In the first step, we divide the core into channels with size equivalent to a fuel assembly. >From this analysis, the channel with the largest enthalpy is identified as the hot assembly. In the second step, we divide the hottest fuel assembly into sub-channels with size equivalent to one actual coolant channel. As in the previous step, the sub-channel with largest final enthalpy is identified as the hottest sub-channel. For the code validation, we considered results from the chinese CARR research reactor. The code reproduced well the CARR reactor results, yielding detailed information such as static pressure in the channel, mass flow rate distribution among the fuel channels, coolant, clad and centerline fuel temperatures, quality and local heat and critical heat

  16. Thermal-hydraulic code for estimating safety limits of nuclear reactors with plate type fuels

    International Nuclear Information System (INIS)

    Castellanos, Duvan A.; Moreira, João L.; Maiorino, Jose R.; Rossi, Pedro R.; Carajilescov, Pedro

    2017-01-01

    To ensure the normal and safe operation of PWR type nuclear reactors is necessary the knowledge of nuclear and heat transfer properties of the fuel, coolant and structural materials. The thermal-hydraulic analysis of nuclear reactors yields parameters such as the distribution of fuel and coolant temperatures, and the departure from nucleated boiling ratio. Usually computational codes are used to analyze the safety performance of the core. This research work presents a computer code for performing thermal-hydraulic analyses of nuclear reactors with plate-type fuel elements operating at low pressure and temperature (research reactors) or high temperature and pressure (naval propulsion or small power reactors). The code uses the sub-channel method based on geometric and thermal-hydraulic conditions. In order to solve the conservation equations for mass, momentum and energy, each sub-channel is divided into control volumes in the axial direction. The mass flow distribution for each fuel element of core is obtained. Analysis of critical heat flux is performed in the hottest channel. The code considers the radial symmetry and the chain or cascade method for two steps in order to facilitate the whole analysis. In the first step, we divide the core into channels with size equivalent to a fuel assembly. >From this analysis, the channel with the largest enthalpy is identified as the hot assembly. In the second step, we divide the hottest fuel assembly into sub-channels with size equivalent to one actual coolant channel. As in the previous step, the sub-channel with largest final enthalpy is identified as the hottest sub-channel. For the code validation, we considered results from the chinese CARR research reactor. The code reproduced well the CARR reactor results, yielding detailed information such as static pressure in the channel, mass flow rate distribution among the fuel channels, coolant, clad and centerline fuel temperatures, quality and local heat and critical heat

  17. Validation of the TASS/SMR-S Code for the PRHRS Condensation Heat Transfer Model

    International Nuclear Information System (INIS)

    Jun, In Sub; Yang, Soo Hyoung; Chung, Young Jong; Lee, Won Jae

    2011-01-01

    When some accidents or events are occurred in the SMART, the secondary system is used to remove the core decay heat for the long time such as a feedwater system. But if the feedwater system can't remove the residual core heat because of its malfunction, the core decay heat is removed using the Passive Residual Heat Removal System (PRHRS). The PRHRS is passive type safety system adopted to enhance the safety of the SMART. It can fundamentally eliminate the uncertainty of operator action. TASS/SMR-S (Transient And Setpoint Simulation/ System-integrated Modular Reactor-Safety) code has various heat transfer models reflecting the design features of the SMART. One of the heat transfer models is the PRHRS condensation heat transfer model. The role of this model is to calculate the heat transfer coefficient in the heat exchanger (H/X) tube side using the relevant heat transfer correlations for all of the heat transfer modes. In this paper, the validation of the condensation heat transfer model was carried out using the POSTECH H/X heat transfer test

  18. Safety analysis and code development for nuclear fuel cycle facilities

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-15

    We are estimating that the debris containing fuel are piled in the containment and the pressure vessel bottoms of Fukushima-Daiichi NPPs. A radioactive Xe concentration discharged in recriticality is being monitored by utilizing the gas management system set up in NPPs unit 1-3. For this reason, we can confirm the recriticality might not be broken out. However, the debris conditions distributed in the containment vessel and the pressure vessel bottoms are not clear. The internal and external surrounding changes will make recriticality become possible. According to TEPCO's roadmap, TEPCO will launch extracting task within 10 years. Even in the case that the fuel condition changes due to debris relocation and mixture, subcriticality must be secured. Criticality safety analysis with non-uniform effect should therefore be essential for the molten debris. For above reasons, we studies the optimum distributions with some parameters that have a large reactivity change were assessed with OPT-DANT code. Finally, the boron concentration was estimated in order to keep subcriticality. (author)

  19. Validation of calculational methods for nuclear criticality safety - approved 1975

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    The American National Standard for Nuclear Criticality Safety in Operations with Fissionable Materials Outside Reactors, N16.1-1975, states in 4.2.5: In the absence of directly applicable experimental measurements, the limits may be derived from calculations made by a method shown to be valid by comparison with experimental data, provided sufficient allowances are made for uncertainties in the data and in the calculations. There are many methods of calculation which vary widely in basis and form. Each has its place in the broad spectrum of problems encountered in the nuclear criticality safety field; however, the general procedure to be followed in establishing validity is common to all. The standard states the requirements for establishing the validity and area(s) of applicability of any calculational method used in assessing nuclear criticality safety

  20. Verification and validation of the safety parameter display system for nuclear power plant

    International Nuclear Information System (INIS)

    Zhang Yuanfang

    1993-05-01

    During the design and development phase of the safety parameter display system for nuclear power plant, a verification and validation (V and V) plan has been implemented to improve the quality of system design. The V and V activities are briefly introduced, which were executed in four stages of feasibility research, system design, code development and system integration and regulation. The evaluation plan and the process of implementation as well as the evaluation conclusion of the final technical validation for this system are also presented in detail

  1. International validation of safety analyses for nuclear power plants; Mednarodno preverjanje varnostnih analiz za jedrske elektrane

    Energy Technology Data Exchange (ETDEWEB)

    Gregoric, N; Mavko, B [Institut ' Jozef Stefan' Ljubljana (Yugoslavia)

    1988-07-01

    Paper describes the participation of 'J.Stefan' Institute in international standard problems for validation of modeling and programs for safety analysis. Listed are main international experimental facilities for collecting data basic for understanding of physical phenomena, code development and validation of modelling and programs. Since the results of international standard problem analyses are published in a joint final report, it is simple to asses the conformance of the results of a particular group with the experiment. Good results from three international exercises done so far, have encouraged the group to currently participate in OECD-ISP-22 which is a model of the Italian three loop PWR. (author)

  2. Development and validation of a fuel performance analysis code

    International Nuclear Information System (INIS)

    Majalee, Aaditya V.; Chaturvedi, S.

    2015-01-01

    CAD has been developing a computer code 'FRAVIZ' for calculation of steady-state thermomechanical behaviour of nuclear reactor fuel rods. It contains four major modules viz., Thermal module, Fission Gas Release module, Material Properties module and Mechanical module. All these four modules are coupled to each other and feedback from each module is fed back to others to get a self-consistent evolution in time. The computer code has been checked against two FUMEX benchmarks. Modelling fuel performance in Advance Heavy Water Reactor would require additional inputs related to the fuel and some modification in the code.(author)

  3. Validity of instruments to assess students' travel and pedestrian safety

    Directory of Open Access Journals (Sweden)

    Baranowski Tom

    2010-05-01

    Full Text Available Abstract Background Safe Routes to School (SRTS programs are designed to make walking and bicycling to school safe and accessible for children. Despite their growing popularity, few validated measures exist for assessing important outcomes such as type of student transport or pedestrian safety behaviors. This research validated the SRTS school travel survey and a pedestrian safety behavior checklist. Methods Fourth grade students completed a brief written survey on how they got to school that day with set responses. Test-retest reliability was obtained 3-4 hours apart. Convergent validity of the SRTS travel survey was assessed by comparison to parents' report. For the measure of pedestrian safety behavior, 10 research assistants observed 29 students at a school intersection for completion of 8 selected pedestrian safety behaviors. Reliability was determined in two ways: correlations between the research assistants' ratings to that of the Principal Investigator (PI and intraclass correlations (ICC across research assistant ratings. Results The SRTS travel survey had high test-retest reliability (κ = 0.97, n = 96, p Conclusions These validated instruments can be used to assess SRTS programs. The pedestrian safety behavior checklist may benefit from further formative work.

  4. PIV Uncertainty Methodologies for CFD Code Validation at the MIR Facility

    Energy Technology Data Exchange (ETDEWEB)

    Sabharwall, Piyush [Idaho National Lab. (INL), Idaho Falls, ID (United States); Skifton, Richard [Idaho National Lab. (INL), Idaho Falls, ID (United States); Stoots, Carl [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kim, Eung Soo [Idaho National Lab. (INL), Idaho Falls, ID (United States); Conder, Thomas [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2013-12-01

    Currently, computational fluid dynamics (CFD) is widely used in the nuclear thermal hydraulics field for design and safety analyses. To validate CFD codes, high quality multi dimensional flow field data are essential. The Matched Index of Refraction (MIR) Flow Facility at Idaho National Laboratory has a unique capability to contribute to the development of validated CFD codes through the use of Particle Image Velocimetry (PIV). The significance of the MIR facility is that it permits non intrusive velocity measurement techniques, such as PIV, through complex models without requiring probes and other instrumentation that disturb the flow. At the heart of any PIV calculation is the cross-correlation, which is used to estimate the displacement of particles in some small part of the image over the time span between two images. This image displacement is indicated by the location of the largest peak. In the MIR facility, uncertainty quantification is a challenging task due to the use of optical measurement techniques. Currently, this study is developing a reliable method to analyze uncertainty and sensitivity of the measured data and develop a computer code to automatically analyze the uncertainty/sensitivity of the measured data. The main objective of this study is to develop a well established uncertainty quantification method for the MIR Flow Facility, which consists of many complicated uncertainty factors. In this study, the uncertainty sources are resolved in depth by categorizing them into uncertainties from the MIR flow loop and PIV system (including particle motion, image distortion, and data processing). Then, each uncertainty source is mathematically modeled or adequately defined. Finally, this study will provide a method and procedure to quantify the experimental uncertainty in the MIR Flow Facility with sample test results.

  5. Software coding for reliable data communication in a reactor safety system

    International Nuclear Information System (INIS)

    Maghsoodi, R.

    1978-01-01

    A software coding method is proposed to improve the communication reliability of a microprocessor based fast-reactor safety system. This method which replaces the conventional coding circuitry, applies a program to code the data which is communicated between the processors via their data memories. The system requirements are studied and the suitable codes are suggested. The problems associated with hardware coders, and the advantages of software coding methods are discussed. The product code which proves a faster coding time over the cyclic code is chosen as the final code. Then the improvement of the communication reliability is derived for a processor and its data memory. The result is used to calculate the reliability improvement of the processing channel as the basic unit for the safety system. (author)

  6. Description and validation of ANTEO, an optimised PC code the thermalhydraulic analysis of fuel bundles

    International Nuclear Information System (INIS)

    Cevolani, S.

    1995-01-01

    The paper deals with the description of a Personal Computer oriented subchannel code, devoted to the steady state thermal hydraulic analysis of nuclear reactor fuel bundles. The development of such a code was made possible by two facts: firstly, the increase, in the computing power of the desk machines; secondly, the fact that several years of experience into operate subchannels codes have shown how to simplify many of the physical models without a sensible loss of accuracy. For sake of validation, the developed code was compared with a traditional subchannel code, the COBRA one. The results of the comparison show a very good agreement between the two codes. (author)

  7. In-core fuel management code package validation for BWRs

    International Nuclear Information System (INIS)

    1995-12-01

    The main goal of the present CRP (Coordinated Research Programme) was to develop benchmarks which are appropriate to check and improve the fuel management computer code packages and their procedures. Therefore, benchmark specifications were established which included a set of realistic data for running in-core fuel management codes. Secondly, the results of measurements and/or operating data were also provided to verify and compare with these parameters as calculated by the in-core fuel management codes or code packages. For the BWR it was established that the Mexican Laguna Verde 1 BWR would serve as the model for providing data on the benchmark specifications. It was decided to provide results for the first 2 cycles of Unit 1 of the Laguna Verde reactor. The analyses of the above benchmarks are performed in two stages. In the first stage, the lattice parameters are generated as a function of burnup at different voids and with and without control rod. These lattice parameters form the input for 3-dimensional diffusion theory codes for over-all reactor analysis. The lattice calculations were performed using different methods, such as, Monte Carlo, 2-D integral transport theory methods. Supercell Model and transport-diffusion model with proper correction for burnable absorber. Thus the variety of results should provide adequate information for any institute or organization to develop competence to analyze In-core fuel management codes. 15 refs, figs and tabs

  8. Obtaining Valid Safety Data for Software Safety Measurement and Process Improvement

    Science.gov (United States)

    Basili, Victor r.; Zelkowitz, Marvin V.; Layman, Lucas; Dangle, Kathleen; Diep, Madeline

    2010-01-01

    We report on a preliminary case study to examine software safety risk in the early design phase of the NASA Constellation spaceflight program. Our goal is to provide NASA quality assurance managers with information regarding the ongoing state of software safety across the program. We examined 154 hazard reports created during the preliminary design phase of three major flight hardware systems within the Constellation program. Our purpose was two-fold: 1) to quantify the relative importance of software with respect to system safety; and 2) to identify potential risks due to incorrect application of the safety process, deficiencies in the safety process, or the lack of a defined process. One early outcome of this work was to show that there are structural deficiencies in collecting valid safety data that make software safety different from hardware safety. In our conclusions we present some of these deficiencies.

  9. Validation of the CATHARE2 code against experimental data from Brayton-cycle plants

    International Nuclear Information System (INIS)

    Bentivoglio, Fabrice; Tauveron, Nicolas; Geffraye, Genevieve; Gentner, Herve

    2008-01-01

    In recent years the Commissariat a l'Energie Atomique (CEA) has commissioned a wide range of feasibility studies of future-advanced nuclear reactors, in particular gas-cooled reactors (GCR). The thermohydraulic behaviour of these systems is a key issue for, among other things, the design of the core, the assessment of thermal stresses, and the design of decay heat removal systems. These studies therefore require efficient and reliable simulation tools capable of modelling the whole reactor, including the core, the core vessel, piping, heat exchangers and turbo-machinery. CATHARE2 is a thermal-hydraulic 1D reference safety code developed and extensively validated for the French pressurized water reactors. It has been recently adapted to deal also with gas-cooled reactor applications. In order to validate CATHARE2 for these new applications, CEA has initiated an ambitious long-term experimental program. The foreseen experimental facilities range from small-scale loops for physical correlations, to component technology and system demonstration loops. In the short-term perspective, CATHARE2 is being validated against existing experimental data. And in particular from the German power plants Oberhausen I and II. These facilities have both been operated by the German utility Energie Versorgung Oberhausen (E.V.O.) and their power conversion systems resemble to the high-temperature reactor concepts: Oberhausen I is a 13.75-MWe Brayton-cycle air turbine plant, and Oberhausen II is a 50-MWe Brayton-cycle helium turbine plant. The paper presents these two plants, the adopted CATHARE2 modelling and a comparison between experimental data and code results for both steady state and transient cases

  10. Three computer codes for safety and stability of large superconducting magnets

    International Nuclear Information System (INIS)

    Turner, L.R.

    1985-01-01

    For analyzing the safety and stability of large superconducting magnets, three computer codes TASS, SHORTURN, and SSICC have been developed, applicable to bath-cooled magnets, bath-cooled magnets with shorted turns, and magnets with internally cooled conductors respectively. The TASS code is described, and the use of the three codes is reviewed

  11. Validity of instruments to assess students' travel and pedestrian safety.

    Science.gov (United States)

    Mendoza, Jason A; Watson, Kathy; Baranowski, Tom; Nicklas, Theresa A; Uscanga, Doris K; Hanfling, Marcus J

    2010-05-18

    Safe Routes to School (SRTS) programs are designed to make walking and bicycling to school safe and accessible for children. Despite their growing popularity, few validated measures exist for assessing important outcomes such as type of student transport or pedestrian safety behaviors. This research validated the SRTS school travel survey and a pedestrian safety behavior checklist. Fourth grade students completed a brief written survey on how they got to school that day with set responses. Test-retest reliability was obtained 3-4 hours apart. Convergent validity of the SRTS travel survey was assessed by comparison to parents' report. For the measure of pedestrian safety behavior, 10 research assistants observed 29 students at a school intersection for completion of 8 selected pedestrian safety behaviors. Reliability was determined in two ways: correlations between the research assistants' ratings to that of the Principal Investigator (PI) and intraclass correlations (ICC) across research assistant ratings. The SRTS travel survey had high test-retest reliability (kappa = 0.97, n = 96, p < 0.001) and convergent validity (kappa = 0.87, n = 81, p < 0.001). The pedestrian safety behavior checklist had moderate reliability across research assistants' ratings (ICC = 0.48) and moderate correlation with the PI (r = 0.55, p = < 0.01). When two raters simultaneously used the instrument, the ICC increased to 0.65. Overall percent agreement (91%), sensitivity (85%) and specificity (83%) were acceptable. These validated instruments can be used to assess SRTS programs. The pedestrian safety behavior checklist may benefit from further formative work.

  12. Validation of KENO V.a for criticality safety calculations involving WR-1 fast-neutron fuel arrangements

    Energy Technology Data Exchange (ETDEWEB)

    Gauld, I. C.

    1991-07-15

    The KENO V.a criticality safety code, used with the SCALE 27-energy-group ENDF/B-IV-based cross-section library, has been validated for low-enriched uranium carbide (UC) WR-1 fast-neutron (FN) fuel arrangements. Because of a lack of relevant experimental data for UC fuel in the published literature, the validation is based primarily on calculational comparisons with critical experiments for fuel types with a range of enrichments and densities that cover those of the FN UC fuel. The ability of KENO V.a to handle the unique annular pin arrangement of the WR-1 FN fuel bundle was established using a comparison with the MCNP3B code used with a continuous-energy ENDF/B-V-based cross-section library. This report is part of the AECL--10146 report series documenting the validation of the KENO V.a criticality safety code.

  13. Development and validation of a remote home safety protocol.

    Science.gov (United States)

    Romero, Sergio; Lee, Mi Jung; Simic, Ivana; Levy, Charles; Sanford, Jon

    2018-02-01

    Environmental assessments and subsequent modifications conducted by healthcare professionals can enhance home safety and promote independent living. However, travel time, expense and the availability of qualified professionals can limit the broad application of this intervention. Remote technology has the potential to increase access to home safety evaluations. This study describes the development and validation of a remote home safety protocol that can be used by a caregiver of an elderly person to video-record their home environment for later viewing and evaluation by a trained professional. The protocol was developed based on literature reviews and evaluations from clinical and content experts. Cognitive interviews were conducted with a group of six caregivers to validate the protocol. The final protocol included step-by-step directions to record indoor and outdoor areas of the home. The validation process resulted in modifications related to safety, clarity of the protocol, readability, visual appearance, technical descriptions and usability. Our final protocol includes detailed instructions that a caregiver should be able to follow to record a home environment for subsequent evaluation by a home safety professional. Implications for Rehabilitation The results of this study have several implications for rehabilitation practice The remote home safety evaluation protocol can potentially improve access to rehabilitation services for clients in remote areas and prevent unnecessary delays for needed care. Using our protocol, a patient's caregiver can partner with therapists to quickly and efficiently evaluate a patient's home before they are released from the hospital. Caregiver narration, which reflects a caregiver's own perspective, is critical to evaluating home safety. In-home safety evaluations, currently not available to all who need them due to access barriers, can enhance a patient's independence and provide a safer home environment.

  14. Development of time dependent safety analysis code for plasma anomaly events in fusion reactors

    International Nuclear Information System (INIS)

    Honda, Takuro; Okazaki, Takashi; Bartels, H.W.; Uckan, N.A.; Seki, Yasushi.

    1997-01-01

    A safety analysis code SAFALY has been developed to analyze plasma anomaly events in fusion reactors, e.g., a loss of plasma control. The code is a hybrid code comprising a zero-dimensional plasma dynamics and a one-dimensional thermal analysis of in-vessel components. The code evaluates the time evolution of plasma parameters and temperature distributions of in-vessel components. As the plasma-safety interface model, we proposed a robust plasma physics model taking into account updated data for safety assessment. For example, physics safety guidelines for beta limit, density limit and H-L mode confinement transition threshold power, etc. are provided in the model. The model of the in-vessel components are divided into twenty temperature regions in the poloidal direction taking account of radiative heat transfer between each surface of each region. This code can also describe the coolant behavior under hydraulic accidents with the results by hydraulics code and treat vaporization (sublimation) from plasma facing components (PFCs). Furthermore, the code includes the model of impurity transport form PFCs by using a transport probability and a time delay. Quantitative analysis based on the model is possible for a scenario of plasma passive shutdown. We examined the possibility of the code as a safety analysis code for plasma anomaly events in fusion reactors and had a prospect that it would contribute to the safety analysis of the International Thermonuclear Experimental Reactor (ITER). (author)

  15. Testing the new stochastic neutronic code ANET in simulating safety important parameters

    International Nuclear Information System (INIS)

    Xenofontos, T.; Delipei, G.-K.; Savva, P.; Varvayanni, M.; Maillard, J.; Silva, J.; Catsaros, N.

    2017-01-01

    Highlights: • ANET is a new neutronics stochastic code. • Criticality calculations in both subcritical and critical nuclear systems of conventional design were conducted. • Simulations of thermal, lower epithermal and fast neutron fluence rates were performed. • Axial fission rate distributions in standard and MOX fuel pins were computed. - Abstract: ANET (Advanced Neutronics with Evolution and Thermal hydraulic feedback) is an under development Monte Carlo code for simulating both GEN II/III reactors as well as innovative nuclear reactor designs, based on the high energy physics code GEANT3.21 of CERN. ANET is built through continuous GEANT3.21 applicability amplifications, comprising the simulation of particles’ transport and interaction in low energy along with the accessibility of user-provided libraries and tracking algorithms for energies below 20 MeV, as well as the simulation of elastic and inelastic collision, capture and fission. Successive testing applications performed throughout the ANET development have been utilized to verify the new code capabilities. In this context the ANET reliability in simulating certain reactor parameters important to safety is here examined. More specifically the reactor criticality as well as the neutron fluence and fission rates are benchmarked and validated. The Portuguese Research Reactor (RPI) after its conversion to low enrichment in U-235 and the OECD/NEA VENUS-2 MOX international benchmark were considered appropriate for the present study, the former providing criticality and neutron flux data and the latter reaction rates. Concerning criticality benchmarking, the subcritical, Training Nuclear Reactor of the Aristotle University of Thessaloniki (TNR-AUTh) was also analyzed. The obtained results are compared with experimental data from the critical infrastructures and with computations performed by two different, well established stochastic neutronics codes, i.e. TRIPOLI-4.8 and MCNP5. Satisfactory agreement

  16. Analysis of SCARABEE BE+3 experiment with ASTEC-Na and comparison with other SFR safety analysis codes

    International Nuclear Information System (INIS)

    Bandini, Giacomino; Ederli, Stefano; Perez-Martin, Sara; Pfrang, Werner; Girault, Nathalie; Cloarec, Laure

    2017-01-01

    The ASTEC-Na code was further developed and assessed in the frame of JASMIN project of the 7th EU Framework Program to extend the original capability of ASTEC, dealing with severe accident analysis in LWR to Sodium-cooled Fast Reactors (SFR). The in-pile BE+3 experiment from the SCARABEE-N program has been simulated with ASTEC-Na for thermal-hydraulic models validation purpose. The adequacy of ASTEC-Na thermal-hydraulic models has been also investigated through the comparison with other safety analysis codes. The analysis of SCARABEE BE+3 test confirms the good performance of ASTEC-Na code in the calculation of single-phase conditions and boiling onset, while larger deviations are encountered in the analysis of the two-phase conditions, mainly regarding the propagation of the boiling front. Furthermore, reasonable agreement was found with other code results. (author)

  17. On-line validation of safety parameters and fault identification

    International Nuclear Information System (INIS)

    Tzanos, C.P.

    1985-01-01

    In many safety-significant off-normal events, the reliability of failure identification and corrective operator actions is limited greatly by the large amount of data that has to be processed and analyzed mentally in a very short time and in a high-stress environment. A data-validation and fault-identification system, that uses computers for continuous plant-information processing and analysis, can enhance plant safety and also improve plant availability. A methodology has been developed that provides validation of safety-significant plant parameter measurements, plant state verification, and fault identification in the presence of many instrumentation failures (including multiple common-cause failures). This paper presents this methodology and some results of its application to a reference LMFBR plant. The basic features of this methodology and the results of its application are summarized

  18. Safety analysis code SCTRAN development for SCWR and its application to CGNPC SCWR

    International Nuclear Information System (INIS)

    Wu, Pan; Gou, Junli; Shan, Jianqiang; Jiang, Yang; Yang, Jue; Zhang, Bo

    2013-01-01

    Highlights: ► A new safety analysis code named SCTRAN is developed for SCWRs. ► Capability of SCTRAN is verified by comparing with code APROS and RELAP5-3D. ► A new passive safety system is proposed for CGNPC SCWR and analyzed with SCTRAN. ► CGNPC SCWR is able to cope with two critical accidents for SCWRs, LOFA and LOCA. - Abstract: Design analysis is one of the main difficulties during the research and design of SCWRs. Currently, the development of safety analysis code for SCWR is still in its infancy all around the world, and very few computer codes could carry out the trans-critical calculations where significant changes in water properties would take place. In this paper, a safety analysis code SCTRAN for SCWRs has been developed based on code RETRAN-02, the best estimate code used for safety analysis of light water reactors. The ability of SCTRAN code to simulate transients where both supercritical and subcritical regimes are encountered has been verified by comparing with APROS and RELAP5-3D codes. Furthermore, the LOFA and LOCA transients for the CGNPC SCWR design were analyzed with SCTRAN code. The characteristics and performance of the passive safety systems applied to CGNPC SCWR were evaluated. The results show that: (1) The SCTRAN computer code developed in this study is capable to perform design analysis for SCWRs; (2) During LOFA and LOCA accidents in a CGNPC SCWR, the passive safety systems would significantly mitigate the consequences of these transients and enhance the inherent safety

  19. Some Findings from Thermal-Hydraulic Validation Tests for SMART Passive Safety System

    Energy Technology Data Exchange (ETDEWEB)

    Park, Hyun Sik; Bae, Hwang; Ryu, Sung-Uk; Ryu, Hyobong; Shin, Yong-Cheol; Min, Kyoung-Ho; Yi, Sung-Jae [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    To satisfy the domestic and international needs for nuclear safety improvement after the Fukushima accident, an effort to improve its safety has been studied, and a Passive Safety System (PSS) for SMART has been designed. In addition, an Integral Test Loop for the SMART design (SMART-ITL, or FESTA) has been constructed and it finished its commissioning tests in 2012. Consequently, a set of Design Base Accident (DBA) scenarios have been simulated using SMARTITL. Recently, a test program to validate the performance of the SMART PSS was launched and its scaled-down test facility was additionally installed at the existing SMART-ITL facility. In this paper, some findings from the validation tests for the SMART PSS will be summarized. The acquired data will be used to validate the safety analysis code and its related models, to evaluate the performance of SMART PSS, and to provide base data during the application phase of SDA revision and construction licensing. A test program to validate the performance of SMARS PSS was launched with an additional scaleddown test facility of SMART PSS, which will be installed at the existing SMART-ITL facility. In this paper, some findings from the validation tests of the SMART passive safety system during 2013-2014 were summarized. They include a couple of SMART PSS tests using active pumps and several 1-train SMART PSS tests. From the test results it was estimated that the SMART PSS has sufficient cooling capability to deal with the SBLOCA scenario of SMART. During the SBLOCA scenario, in the CMT the water layer inventory was well stratified thermally and the safety injection water was injected efficiently into the RPV from the initial period and cools down the RCS properly.

  20. Experimental validation of decay heat calculation codes and associated nuclear data libraries for fusion energy

    International Nuclear Information System (INIS)

    Maekawa, Fujio; Wada, Masayuki; Ikeda, Yujiro

    2001-01-01

    Validity of decay heat calculations for safety designs of fusion reactors was investigated by using decay heat experimental data on thirty-two fusion reactor relevant materials obtained at the 14-MeV neutron source facility of FNS in JAERI. Calculation codes developed in Japan, ACT4 and CINAC version 4, and nuclear data bases such as JENDL/Act-96, FENDL/A-2.0 and Lib90 were used for the calculation. Although several corrections in algorithms for both the calculation codes were needed, it was shown by comparing calculated results with the experimental data that most of activation cross sections and decay data were adequate. In cases of type 316 stainless steel and copper which were important for ITER, prediction accuracy of decay heat within ±10% was confirmed. However, it was pointed out that there were some problems in parts of data such as improper activation cross sections, e,g., the 92 Mo(n, 2n) 91g Mo reaction in FENDL, and lack of activation cross section data, e.g., the 138 Ba(n, 2n) 137m Ba reaction in JENDL. Modifications of cross section data were recommended for 19 reactions in JENDL and FENDL. It was also pointed out that X-ray and conversion electron energies should be included in decay data. (author)

  1. Experimental validation of decay heat calculation codes and associated nuclear data libraries for fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    Maekawa, Fujio; Wada, Masayuki; Ikeda, Yujiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-01-01

    Validity of decay heat calculations for safety designs of fusion reactors was investigated by using decay heat experimental data on thirty-two fusion reactor relevant materials obtained at the 14-MeV neutron source facility of FNS in JAERI. Calculation codes developed in Japan, ACT4 and CINAC version 4, and nuclear data bases such as JENDL/Act-96, FENDL/A-2.0 and Lib90 were used for the calculation. Although several corrections in algorithms for both the calculation codes were needed, it was shown by comparing calculated results with the experimental data that most of activation cross sections and decay data were adequate. In cases of type 316 stainless steel and copper which were important for ITER, prediction accuracy of decay heat within {+-}10% was confirmed. However, it was pointed out that there were some problems in parts of data such as improper activation cross sections, e,g., the {sup 92}Mo(n, 2n){sup 91g}Mo reaction in FENDL, and lack of activation cross section data, e.g., the {sup 138}Ba(n, 2n){sup 137m}Ba reaction in JENDL. Modifications of cross section data were recommended for 19 reactions in JENDL and FENDL. It was also pointed out that X-ray and conversion electron energies should be included in decay data. (author)

  2. Cross-index to DOE-prescribed occupational safety codes and standards

    International Nuclear Information System (INIS)

    1981-01-01

    This Cross-Index volume is the 1981 compilation of detailed information from more than three hundred and fifty DOE prescribed or OSHA referenced industrial safety codes and standards and is revised yearly to provide information from current codes. Condensed data from individual code portions are listed according to reference code, section, paragraph and page. Each code is given a two-digit reference code number or letter in the Contents section (pages C to L) of this volume. This reference code provides ready identification of any code listed in the Cross-Index. The computerized information listings are on the left-hand portion of Cross-Index page; in order to the right of the listing are the reference code letters or numbers, the section, paragraph and page of the referenced code containing expanded information on the individual listing

  3. Code development and analyses within the area of transmutation and safety

    International Nuclear Information System (INIS)

    Maschek, W.

    2002-01-01

    A strong code development is going on to meet various demands resulting from the development of dedicated reactors for transmutation and incineration. Code development is concerned with safety codes and general codes needed for assessing scenarios and transmutation strategies. Analyses concentrate on various ADS systems with solid and liquid molten salt fuels. Analyses deal with ADS Demo Plant (5th FP EU) and transmuters with advanced fuels

  4. Cross-index to DOE-prescribed occupational safety codes and standards

    International Nuclear Information System (INIS)

    1982-01-01

    A compilation of detailed information from more than three hundred and fifty DOE-prescribed or OSHA-referenced industrial safety codes and standards is presented. Condensed data from individual code portions are listed according to reference code, section, paragraph and page. A glossary of letter initials/abbreviations for the organizations or documents whose codes or standards are contained in this Cross-Index, is listed

  5. Code of Practice containing definitions for Safety Codes of Practice for nuclear power plants

    International Nuclear Information System (INIS)

    1979-01-01

    This Code provides definitions of the technical terms used in the licensing applications to be submitted to the Turkish Atomic Energy Commission (TAEC), in accordance with national licensing regulations. The Code is based mainly on the International Atomic Energy Agency's Code of Practice on the subject. (NEA) [fr

  6. Trustworthy Variant Derivation with Translation Validation for Safety Critical Product Lines

    DEFF Research Database (Denmark)

    Iosif-Lazăr, Alexandru Florin; Wasowski, Andrzej

    2016-01-01

    Software product line (SPL) engineering facilitates development of entire families of software products with systematic reuse. Model driven SPLs use models in the design and development process. In the safety critical domain, validation of models and testing of code increases the quality...... of the products altogether. However, to maintain this trustworthiness it is necessary to know that the SPL tools, which manipulate models and code to derive concrete product variants, do not introduce errors in the process. We propose a general technique of checking correctness of product derivation tools through...... translation validation. We demonstrate it using Featherweight VML—a core language for separate variability modeling relying on a single kind of variation point to define transformations of artifacts seen as object models. We use Featherweight VML with its semantics as a correctness specification...

  7. Validation of Advanced Computer Codes for VVER Technology: LB-LOCA Transient in PSB-VVER Facility

    Directory of Open Access Journals (Sweden)

    A. Del Nevo

    2012-01-01

    Full Text Available The OECD/NEA PSB-VVER project provided unique and useful experimental data for code validation from PSB-VVER test facility. This facility represents the scaled-down layout of the Russian-designed pressurized water reactor, namely, VVER-1000. Five experiments were executed, dealing with loss of coolant scenarios (small, intermediate, and large break loss of coolant accidents, a primary-to-secondary leak, and a parametric study (natural circulation test aimed at characterizing the VVER system at reduced mass inventory conditions. The comparative analysis, presented in the paper, regards the large break loss of coolant accident experiment. Four participants from three different institutions were involved in the benchmark and applied their own models and set up for four different thermal-hydraulic system codes. The benchmark demonstrated the performances of such codes in predicting phenomena relevant for safety on the basis of fixed criteria.

  8. First steps towards a validation of the new burnup and depletion code TNT

    Energy Technology Data Exchange (ETDEWEB)

    Herber, S.C.; Allelein, H.J. [RWTH Aachen (Germany). Inst. for Reactor Safety and Reactor Technology; Research Center Juelich (Germany). Inst. for Energy and Climate Research - Nuclear Waste Disposal and Reactor Safety (IEK-6); Friege, N. [RWTH Aachen (Germany). Inst. for Reactor Safety and Reactor Technology; Kasselmann, S. [Research Center Juelich (Germany). Inst. for Energy and Climate Research - Nuclear Waste Disposal and Reactor Safety (IEK-6)

    2012-11-01

    In the frame of the fusion of the core design calculation capabilities, represented by V.S.O.P., and the accident calculation capabilities, represented by MGT(-3D), the successor of the TINTE code, difficulties were observed in defining an interface between a program backbone and the ORIGEN code respectively the ORIGENJUEL code. The estimation of the effort of refactoring the ORIGEN code or to write a new burnup code from scratch, led to the decision that it would be more efficient writing a new code, which could benefit from existing programming and software engineering tools from the computer code side and which can use the latest knowledge of nuclear reactions, e.g. consider all documented reaction channels. Therefore a new code with an object-oriented approach was developed at IEK-6. Object-oriented programming is currently state of the art and provides mostly an improved extensibility and maintainability. The new code was named TNT which stands for Topological Nuclide Transformation, since the code makes use of the real topology of the nuclear reactions. Here we want to present some first validation results from code to code benchmarks with the codes ORIGEN V2.2 and FISPACT2005 and whenever possible analytical results also used for the comparison. The 2 reference codes were chosen due to their high reputation in the field of fission reactor analysis (ORIGEN) and fusion facilities (FISPACT). (orig.)

  9. Toward a CFD nose-to-tail capability - Hypersonic unsteady Navier-Stokes code validation

    Science.gov (United States)

    Edwards, Thomas A.; Flores, Jolen

    1989-01-01

    Computational fluid dynamics (CFD) research for hypersonic flows presents new problems in code validation because of the added complexity of the physical models. This paper surveys code validation procedures applicable to hypersonic flow models that include real gas effects. The current status of hypersonic CFD flow analysis is assessed with the Compressible Navier-Stokes (CNS) code as a case study. The methods of code validation discussed to beyond comparison with experimental data to include comparisons with other codes and formulations, component analyses, and estimation of numerical errors. Current results indicate that predicting hypersonic flows of perfect gases and equilibrium air are well in hand. Pressure, shock location, and integrated quantities are relatively easy to predict accurately, while surface quantities such as heat transfer are more sensitive to the solution procedure. Modeling transition to turbulence needs refinement, though preliminary results are promising.

  10. Is the international safety management code an organisational tool ...

    African Journals Online (AJOL)

    The birth of the International Management Code for the Safe Operation of Ships and for Pollution Prevention (hereinafter ISM Code) is said to a reaction to the sinking of the Herald of free Enterprise on 6th March 1987.The human element is said to be a generic term used to describe what makes humans behave the way ...

  11. ITER safety studies: starting the quality plan code AINA

    International Nuclear Information System (INIS)

    Dies, J.; Rivas, J. C.; Bargallo, E.

    2010-01-01

    This contribution discusses the implementation of the Quality Plan AINA Code 2.0. The work has affected areas such as the life cycle model, the software reliability plan, the design of the equipment or software tools to use, and has finally produced a new code.

  12. Validation of the THIRMAL-1 melt-water interaction code

    Energy Technology Data Exchange (ETDEWEB)

    Chu, C.C.; Sienicki, J.J.; Spencer, B.W. [Argonne National Lab., IL (United States)

    1995-09-01

    The THIRMAL-1 computer code has been used to calculate nonexplosive LWR melt-water interactions both in-vessel and ex-vessel. To support the application of the code and enhance its acceptability, THIRMAL-1 has been compared with available data from two of the ongoing FARO experiments at Ispra and two of the Corium Coolant Mixing (CCM) experiments performed at Argonne. THIRMAL-1 calculations for the FARO Scoping Test and Quenching Test 2 as well as the CCM-5 and -6 experiments were found to be in excellent agreement with the experiment results. This lends confidence to the modeling that has been incorporated in the code describing melt stream breakup due to the growth of both Kelvin-Helmholtz and large wave instabilities, the sizes of droplets formed, multiphase flow and heat transfer in the mixing zone surrounding and below the melt metallic phase. As part of the analysis of the FARO tests, a mechanistic model was developed to calculate the prefragmentation as it may have occurred when melt relocated from the release vessel to the water surface and the model was compared with the relevant data from FARO.

  13. Study of experimental validation for combustion analysis of GOTHIC code

    International Nuclear Information System (INIS)

    Lee, J. Y.; Yang, S. Y.; Park, K. C.; Jeong, S. H.

    2001-01-01

    In this study, present lumped and subdivided GOTHIC6 code analyses of the premixed hydrogen combustion experiment at the Seoul National University and comparison with the experiment results. The experimental facility has 16367 cc free volume and rectangular shape. And the test was performed with unit equivalence ratio of the hydrogen and air, and with various location of igniter position. Using the lumped and mechanistic combustion model in GOTHIC6 code, the experiments were simulated with the same conditions. In the comparison between experiment and calculated results, the GOTHIC6 prediction of the combustion response does not compare well with the experiment results. In the point of combustion time, the lumped combustion model of GOTHIC6 code does not simulate the physical phenomena of combustion appropriately. In the case of mechanistic combustion model, the combustion time is predicted well, but the induction time of calculation data is longer than the experiment data remarkably. Also, the laminar combustion model of GOTHIC6 has deficiency to simulate combustion phenomena unless control the user defined value appropriately. And the pressure is not a proper variable that characterize the three dimensional effect of combustion

  14. ASTEC V2 severe accident integral code: Fission product modelling and validation

    International Nuclear Information System (INIS)

    Cantrel, L.; Cousin, F.; Bosland, L.; Chevalier-Jabet, K.; Marchetto, C.

    2014-01-01

    One main goal of the severe accident integral code ASTEC V2, jointly developed since almost more than 15 years by IRSN and GRS, is to simulate the overall behaviour of fission products (FP) in a damaged nuclear facility. ASTEC applications are source term determinations, level 2 Probabilistic Safety Assessment (PSA2) studies including the determination of uncertainties, accident management studies and physical analyses of FP experiments to improve the understanding of the phenomenology. ASTEC is a modular code and models of a part of the phenomenology are implemented in each module: the release of FPs and structural materials from degraded fuel in the ELSA module; the transport through the reactor coolant system approximated as a sequence of control volumes in the SOPHAEROS module; and the radiochemistry inside the containment nuclear building in the IODE module. Three other modules, CPA, ISODOP and DOSE, allow respectively computing the deposition rate of aerosols inside the containment, the activities of the isotopes as a function of time, and the gaseous dose rate which is needed to model radiochemistry in the gaseous phase. In ELSA, release models are semi-mechanistic and have been validated for a wide range of experimental data, and noticeably for VERCORS experiments. For SOPHAEROS, the models can be divided into two parts: vapour phase phenomena and aerosol phase phenomena. For IODE, iodine and ruthenium chemistry are modelled based on a semi-mechanistic approach, these FPs can form some volatile species and are particularly important in terms of potential radiological consequences. The models in these 3 modules are based on a wide experimental database, resulting for a large part from international programmes, and they are considered at the state of the art of the R and D knowledge. This paper illustrates some FPs modelling capabilities of ASTEC and computed values are compared to some experimental results, which are parts of the validation matrix

  15. Validation Study of CODES Dragonfly Network Model with Theta Cray XC System

    Energy Technology Data Exchange (ETDEWEB)

    Mubarak, Misbah [Argonne National Lab. (ANL), Argonne, IL (United States); Ross, Robert B. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2017-05-31

    This technical report describes the experiments performed to validate the MPI performance measurements reported by the CODES dragonfly network simulation with the Theta Cray XC system at the Argonne Leadership Computing Facility (ALCF).

  16. A Systematic Method for Verification and Validation of Gyrokinetic Microstability Codes

    Energy Technology Data Exchange (ETDEWEB)

    Bravenec, Ronald [Fourth State Research, Austin, TX (United States)

    2017-11-14

    My original proposal for the period Feb. 15, 2014 through Feb. 14, 2017 called for an integrated validation and verification effort carried out by myself with collaborators. The validation component would require experimental profile and power-balance analysis. In addition, it would require running the gyrokinetic codes varying the input profiles within experimental uncertainties to seek agreement with experiment before discounting a code as invalidated. Therefore, validation would require a major increase of effort over my previous grant periods which covered only code verification (code benchmarking). Consequently, I had requested full-time funding. Instead, I am being funded at somewhat less than half time (5 calendar months per year). As a consequence, I decided to forego the validation component and to only continue the verification efforts.

  17. Nuclear Energy Advanced Modeling and Simulation (NEAMS) waste Integrated Performance and Safety Codes (IPSC): gap analysis for high fidelity and performance assessment code development

    International Nuclear Information System (INIS)

    Lee, Joon H.; Siegel, Malcolm Dean; Arguello, Jose Guadalupe Jr.; Webb, Stephen Walter; Dewers, Thomas A.; Mariner, Paul E.; Edwards, Harold Carter; Fuller, Timothy J.; Freeze, Geoffrey A.; Jove-Colon, Carlos F.; Wang, Yifeng

    2011-01-01

    This report describes a gap analysis performed in the process of developing the Waste Integrated Performance and Safety Codes (IPSC) in support of the U.S. Department of Energy (DOE) Office of Nuclear Energy Advanced Modeling and Simulation (NEAMS) Campaign. The goal of the Waste IPSC is to develop an integrated suite of computational modeling and simulation capabilities to quantitatively assess the long-term performance of waste forms in the engineered and geologic environments of a radioactive waste storage or disposal system. The Waste IPSC will provide this simulation capability (1) for a range of disposal concepts, waste form types, engineered repository designs, and geologic settings, (2) for a range of time scales and distances, (3) with appropriate consideration of the inherent uncertainties, and (4) in accordance with rigorous verification, validation, and software quality requirements. The gap analyses documented in this report were are performed during an initial gap analysis to identify candidate codes and tools to support the development and integration of the Waste IPSC, and during follow-on activities that delved into more detailed assessments of the various codes that were acquired, studied, and tested. The current Waste IPSC strategy is to acquire and integrate the necessary Waste IPSC capabilities wherever feasible, and develop only those capabilities that cannot be acquired or suitably integrated, verified, or validated. The gap analysis indicates that significant capabilities may already exist in the existing THC codes although there is no single code able to fully account for all physical and chemical processes involved in a waste disposal system. Large gaps exist in modeling chemical processes and their couplings with other processes. The coupling of chemical processes with flow transport and mechanical deformation remains challenging. The data for extreme environments (e.g., for elevated temperature and high ionic strength media) that are

  18. Nuclear Energy Advanced Modeling and Simulation (NEAMS) waste Integrated Performance and Safety Codes (IPSC) : gap analysis for high fidelity and performance assessment code development.

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Joon H.; Siegel, Malcolm Dean; Arguello, Jose Guadalupe, Jr.; Webb, Stephen Walter; Dewers, Thomas A.; Mariner, Paul E.; Edwards, Harold Carter; Fuller, Timothy J.; Freeze, Geoffrey A.; Jove-Colon, Carlos F.; Wang, Yifeng

    2011-03-01

    This report describes a gap analysis performed in the process of developing the Waste Integrated Performance and Safety Codes (IPSC) in support of the U.S. Department of Energy (DOE) Office of Nuclear Energy Advanced Modeling and Simulation (NEAMS) Campaign. The goal of the Waste IPSC is to develop an integrated suite of computational modeling and simulation capabilities to quantitatively assess the long-term performance of waste forms in the engineered and geologic environments of a radioactive waste storage or disposal system. The Waste IPSC will provide this simulation capability (1) for a range of disposal concepts, waste form types, engineered repository designs, and geologic settings, (2) for a range of time scales and distances, (3) with appropriate consideration of the inherent uncertainties, and (4) in accordance with rigorous verification, validation, and software quality requirements. The gap analyses documented in this report were are performed during an initial gap analysis to identify candidate codes and tools to support the development and integration of the Waste IPSC, and during follow-on activities that delved into more detailed assessments of the various codes that were acquired, studied, and tested. The current Waste IPSC strategy is to acquire and integrate the necessary Waste IPSC capabilities wherever feasible, and develop only those capabilities that cannot be acquired or suitably integrated, verified, or validated. The gap analysis indicates that significant capabilities may already exist in the existing THC codes although there is no single code able to fully account for all physical and chemical processes involved in a waste disposal system. Large gaps exist in modeling chemical processes and their couplings with other processes. The coupling of chemical processes with flow transport and mechanical deformation remains challenging. The data for extreme environments (e.g., for elevated temperature and high ionic strength media) that are

  19. The Development of Severe Accident Codes at IRSN and Their Application to Support the Safety Assessment of EPR

    International Nuclear Information System (INIS)

    Caroli, Cataldo; Bleyer, Alexandre; Bentaib, Ahmed; Chatelard, Patrick; Cranga, Michel; Van Dorsselaere, Jean-Pierre

    2006-01-01

    IRSN uses a two-tier approach for development of codes analysing the course of a hypothetical severe accident (SA) in a Pressurized Water Reactor (PWR): on one hand, the integral code ASTEC, jointly developed by IRSN and GRS, for fast-running and complete analysis of a sequence; on the other hand, detailed codes for best-estimate analysis of some phenomena such as ICARE/CATHARE, MC3D (for steam explosion), CROCO and TONUS. They have been extensively used to support the level 2 Probabilistic Safety Assessment of the 900 MWe PWR and, in general, for the safety analysis of the French PWR. In particular the codes ICARE/CATHARE, CROCO, MEDICIS (module of ASTEC) and TONUS are used to support the safety assessment of the European Pressurized Reactor (EPR). The ICARE/CATHARE code system has been developed for the detailed evaluation of SA consequences in a PWR primary system. It is composed of the coupling of the core degradation IRSN code ICARE2 and of the thermal-hydraulics French code CATHARE2. The CFD code CROCO describes the corium flow in the spreading compartment. Heat transfer to the surrounding atmosphere and to the basemat, leading to the possible formation of an upper and lower crust, basemat ablation and gas sparging through the flow are modelled. CROCO has been validated against a wide experimental basis, including the CORINE, KATS and VULCANO programs. MEDICIS simulates MCCI (Molten-Corium-Concrete-Interaction) using a lumped-parameter approach. Its models are being continuously improved through the interpretation of most MCCI experiments (OECD-CCI, ACE...). The TONUS code has been developed by IRSN in collaboration with CEA for the analysis of the hydrogen risk (both distribution and combustion) in the reactor containment. The analyses carried out to support the EPR safety assessment are based on a CFD formulation. At this purpose a low-Mach number multi-component Navier-Stokes solver is used to analyse the hydrogen distribution. Presence of air, steam and

  20. Context discovery using attenuated Bloom codes: model description and validation

    NARCIS (Netherlands)

    Liu, F.; Heijenk, Geert

    A novel approach to performing context discovery in ad-hoc networks based on the use of attenuated Bloom filters is proposed in this report. In order to investigate the performance of this approach, a model has been developed. This document describes the model and its validation. The model has been

  1. Determination of the NPP Krsko reactor core safety limits using the COBRA-III-C code

    International Nuclear Information System (INIS)

    Lajtman, S.; Feretic, D.; Debrecin, N.

    1989-01-01

    This paper presents the NPP Krsko reactor core safety limits determined by the COBRA-III-C code, along with the methodology used. The reactor core safety limits determination is a part of reactor protection limits procedure. The results obtained were compared to safety limits presented in NPP Krsko FSAR. The COBRA-III-C NPP Krsko design core steady state thermal hydraulics calculation, used as the basis for the safety limits calculation, is presented as well. (author)

  2. Model validation of GAMMA code with heat transfer experiment for KO TBM in ITER

    International Nuclear Information System (INIS)

    Yum, Soo Been; Lee, Eo Hwak; Lee, Dong Won; Park, Goon Cherl

    2013-01-01

    Highlights: ► In this study, helium supplying system was constructed. ► Preparation for heat transfer experiment in KO TBM condition using helium supplying system was progressed. ► To get more applicable results, test matrix was made to cover the condition for KO TBM. ► Using CFD code; CFX 11, validation and modification for system code GAMMA was performed. -- Abstract: By considering the requirements for a DEMO-relevant blanket concept, Korea (KO) has proposed a He cooled molten lithium (HCML) test blanket module (TBM) for testing in ITER. A performance analysis for the thermal–hydraulics and a safety analysis for the KO TBM have been carried out using a commercial CFD code, ANSYS-CFX, and a system code, GAMMA (GAs multicomponent mixture analysis), which was developed by the gas cooled reactor in Korea. To verify the codes, a preliminary study was performed by Lee using a single TBM first wall (FW) mock-up made from the same material as the KO TBM, ferritic martensitic steel, using a 6 MPa nitrogen gas loop. The test was performed at pressures of 1.1, 1.9 and 2.9 MPa, and under various ranges of flow rate from 0.0105 to 0.0407 kg/s with a constant wall temperature condition. In the present study, a thermal–hydraulic test was performed with the newly constructed helium supplying system, in which the design pressure and temperature were 9 MPa and 500 °C, respectively. In the experiment, the same mock-up was used, and the test was performed under the conditions of 3 MPa pressure, 30 °C inlet temperature and 70 m/s helium velocity, which are almost same conditions of the KO TBM FW. One side of the mock-up was heated with a constant heat flux of 0.3–0.5 MW/m 2 using a graphite heating system, KoHLT-2 (Korea heat load test facility-2). Because the comparison result between CFX 11 and GAMMA showed a difference tendency, the modification of heat transfer correlation included in GAMMA was performed. And the modified GAMMA showed the strong parity with CFX

  3. Development of safety analysis codes for light water reactor

    International Nuclear Information System (INIS)

    Akimoto, Masayuki

    1985-01-01

    An overview is presented of currently used major codes for the prediction of thermohydraulic transients in nuclear power plants. The overview centers on the two-phase fluid dynamics of the coolant system and the assessment of the codes. Some of two-phase phenomena such as phase separation are not still predicted with engineering accuracy. MINCS-PIPE are briefly introduced. The MINCS-PIPE code is to assess constitutive relations and to aid development of various experimental correlations for 1V1T model to 2V2T model. (author)

  4. Validation test case generation based on safety analysis ontology

    International Nuclear Information System (INIS)

    Fan, Chin-Feng; Wang, Wen-Shing

    2012-01-01

    Highlights: ► Current practice in validation test case generation for nuclear system is mainly ad hoc. ► This study designs a systematic approach to generate validation test cases from a Safety Analysis Report. ► It is based on a domain-specific ontology. ► Test coverage criteria have been defined and satisfied. ► A computerized toolset has been implemented to assist the proposed approach. - Abstract: Validation tests in the current nuclear industry practice are typically performed in an ad hoc fashion. This study presents a systematic and objective method of generating validation test cases from a Safety Analysis Report (SAR). A domain-specific ontology was designed and used to mark up a SAR; relevant information was then extracted from the marked-up document for use in automatically generating validation test cases that satisfy the proposed test coverage criteria; namely, single parameter coverage, use case coverage, abnormal condition coverage, and scenario coverage. The novelty of this technique is its systematic rather than ad hoc test case generation from a SAR to achieve high test coverage.

  5. MOSEG code for safety oriented maintenance management Safety of management of maintenance oriented by MOSEG code; Codigo MOSEG para la gestion de mantenimiento orientada a la seguridad

    Energy Technology Data Exchange (ETDEWEB)

    Torres Valle, Antonio [Instituto Superior de Tecnologias y Ciencias Aplicadas, La Habana (Cuba). Dept. Ingenieria Nuclear]. E-mail: atorres@fctn.isctn.edu.cu; Rivero Oliva, Jose de Jesus [Centro de Gestion de la Informacion y Desarrollo de la Energia (CUBAENERGIA) (Cuba)]. E-mail: jose@cubaenergia.cu

    2005-07-01

    Full text: One of the main reasons that makes maintenance contribute highly when facing safety problems and facilities availability is the lack of maintenance management systems to solve these fields in a balanced way. Their main setbacks are shown in this paper. It briefly describes the development of an integrating algorithm for a safety and availability-oriented maintenance management by virtue of the MOSEG Win 1.0 code. (author)

  6. Demonstration study on shielding safety analysis code (VI)

    Energy Technology Data Exchange (ETDEWEB)

    Sawamura, Sadashi [Hokkaido Univ., Sapporo (Japan). Faculty of Engineering

    1999-03-01

    Dose evaluation for direct radiation and skyshine from nuclear fuel facilities is one of the environment evaluation items. This evaluation is carried out by using some shielding calculation codes. Because of extremely few benchmark data of skyshine, the calculation has to be performed very conservatively. Therefore, the benchmark data of skyshine and the well-investigated code for skyshine would be necessary to carry out the rational evaluation of nuclear facilities. The purpose of this steady is to obtain the benchmark data of skyshine and to investigate the calculation code for skyshine. In this fiscal year, the followings are investigated; (1) Construction and improvement of a pulsed radiation measurement system due to the gated counting method. (2) Using the system, carried out the radiation monitoring near and in the facility of 45 MeV Linear accelerator installed at Hokkaido University. (3) Simulation analysis of the photo-neutron production and the transport by using the EGS4 and MCNP code. (author)

  7. Test Data for USEPR Severe Accident Code Validation

    Energy Technology Data Exchange (ETDEWEB)

    J. L. Rempe

    2007-05-01

    This document identifies data that can be used for assessing various models embodied in severe accident analysis codes. Phenomena considered in this document, which were limited to those anticipated to be of interest in assessing severe accidents in the USEPR developed by AREVA, include: • Fuel Heatup and Melt Progression • Reactor Coolant System (RCS) Thermal Hydraulics • In-Vessel Molten Pool Formation and Heat Transfer • Fuel/Coolant Interactions during Relocation • Debris Heat Loads to the Vessel • Vessel Failure • Molten Core Concrete Interaction (MCCI) and Reactor Cavity Plug Failure • Melt Spreading and Coolability • Hydrogen Control Each section of this report discusses one phenomenon of interest to the USEPR. Within each section, an effort is made to describe the phenomenon and identify what data are available modeling it. As noted in this document, models in US accident analysis codes (MAAP, MELCOR, and SCDAP/RELAP5) differ. Where possible, this report identifies previous assessments that illustrate the impact of modeling differences on predicting various phenomena. Finally, recommendations regarding the status of data available for modeling USEPR severe accident phenomena are summarized.

  8. Demonstration study on shielding safety analysis code (8)

    Energy Technology Data Exchange (ETDEWEB)

    Sawamura, Sadashi [Hokkaido Univ., Sapporo (Japan)

    2001-03-01

    Dose evaluation for direct radiation and skyshine from nuclear fuel facilities is one of the environment evaluation items. This evaluation is carried out by using some shielding calculation codes. Because of extremely few benchmark data of skyshine, the calculation has to be performed very conservatively. Therefore, the benchmark data of skyshine and the well-investigated code for skyshine would be necessary to carry out the rational evaluation of nuclear facilities. The purpose of this study is to obtain the benchmark data of skyshine and to investigate the calculation code for skyshine. In this fiscal year, the followings are investigated. (1) A {sup 3}He detector and some instruments are added to the former detection system to increase the detection sensitivity in pulsed neutron measurements. Using the new detection system, the skyshine of neutrons from 45 MeV LINAC facility are measured in the distance up to 350 m. (2) To estimate the spectrum of leakage neutron from the facility, {sup 3}He detector with moderators is constructed and the response functions of the detector are calculated using the MCNP simulation code. The leakage spectrum in the facility are measured and unfolded using the SAND-II code. (3) Using the EGS code and/or MCNP code, neutron yields by the photo-nuclear reaction in the lead target are calculated. Then, the neutron fluence at some points including the duct (from which neutrons leaks and is considered to be a skyshine source) is simulated by MCNP MONTE CARLO code. (4) In the distance up to 350 m from the facility, neutron fluence due to the skyshine process are calculated and compared with the experimental results. The comparison gives a fairly good agreement. (author)

  9. Self assessment of safety culture in HANARO using the code of conduct on the safety of research reactor by IAEA

    International Nuclear Information System (INIS)

    Lim, I.C.; Hwang, S.Y.; Woo, J.S.; Lee, M.; Jun, B.J.

    2003-01-01

    Full text: The safety culture in HANARO was self-assessed in accordance with the Code of Conduct on the Safety of Research Reactor drafted by IAEA. From 2002, IAEA has worked on the development of the Code of Conduct to achieve and maintain high level of nuclear safety in research reactors worldwide through the enhancement of national measures and international co-operation including, where appropriate, safety related technical cooperation. It defines the role of the state, the role of the regulatory body, the role of the operating organization and the role of the IAEA. As for the role of operating organization, the code specifies general requirements in assessment and verification of safety, financial and human resources, quality assurance, human factors, radiation protection and emergency preparedness. It also defines the role of operating organization for safety of research reactor in siting, design, operation, maintenance, modification and utilization as well. All of these items are the subjects for safety culture implementation, which means the Code could be a guideline for an operating organization to assess its safety culture. The self-assessment of safety culture in HANARO was made by using the sections of the Code describing the role of the operating organization for safety of research reactor. The major assessment items and the practices in HANARO for each items are as follow: The SAR of HANARO was reviewed by the regulatory body before the construction and the fuel loading of HANARO. Major design modifications and new installation of utilization facility needs the approval from regulatory body and safety assessment is a requirement for the approval. The Tech. Spec. for HANARO Operation specifies the analysis, surveillance, testing and inspection for HANARO operation. The reactor operation is mainly supported by the government and partly by nuclear R and D fund. The education and training of operation staff are one of major tasks of operating organization

  10. Synthesis of clad motion experiments interpretation: codes and validation

    International Nuclear Information System (INIS)

    Papin, J.; Fortunato, M.; Seiler, J.M.

    1983-04-01

    This communication deals with clad melting and relocation phenomena related to LMFBR safety analysis of loss of flow accidents. We present: - the physical models developed at DSN/CEN Cadarache in single channel and bundle geometry. The interpretation with these models of experiments performed by the STT (CEN Grenoble). It comes out that we have now obtained a good understanding of the involved phenomena in single channel geometry. On the other hand, further studies are necessary for a better knowledge of clad motion phenomena in bundle cases with conditions close to reactor ones

  11. The Development of Computer Code for Safety Injection Tank (SIT) with Fluidic Device(FD) Blowdown Test

    International Nuclear Information System (INIS)

    Lee, Joo Hee; Kim, Tae Han; Choi, Hae Yun; Lee, Kwang Won; Chung, Chang Kyu

    2007-01-01

    Safety Injection Tanks (SITs) with the Fluidic Device (FD) of APR1400 provides a means of rapid reflooding of the core following a large break Loss Of Coolant Accident (LOCA), and keeping it covered until flow from the Safety Injection Pump (SIP) becomes available. A passive FD can provide two operation stages of a safety water injection into the RCS and allow more effective use of borated water in case of LOCA. Once a large break LOCA occurs, the system will deliver a high flow rate of cooling water for a certain period of time, and thereafter, the flow rate is reduced to a lower flow rate. The conventional computer code 'TURTLE' used to simulate the blowdown of OPR1000 SIT can not be directly applied to simulate a blowdown process of the SIT with FD. A new computer code is needed to be developed for the blowdown test evaluation of the APR1400 SIT with FD. Korea Power Engineering Company (KOPEC) has developed a new computer code to analyze the characteristics of the SIT with FD and validated the code through the comparison of the calculation results with the test results obtained by Ulchin 5 and 6 units pre-operational test and VAlve Performance Evaluation Rig (VAPER) tests performed by The Korea Atomic Energy Research Institute (KAERI)

  12. FACTAR validation

    International Nuclear Information System (INIS)

    Middleton, P.B.; Wadsworth, S.L.; Rock, R.C.; Sills, H.E.; Langman, V.J.

    1995-01-01

    A detailed strategy to validate fuel channel thermal mechanical behaviour codes for use of current power reactor safety analysis is presented. The strategy is derived from a validation process that has been recently adopted industry wide. Focus of the discussion is on the validation plan for a code, FACTAR, for application in assessing fuel channel integrity safety concerns during a large break loss of coolant accident (LOCA). (author)

  13. IAEA program for the preparation of safety codes and guides for nuclear power plants

    International Nuclear Information System (INIS)

    1975-01-01

    On the 13th of September, 1974, the IAEA Governors' Council has given its consent to the programme for the establishment of safety codes and guides (annex VII to IAEA document G.C. (XVIII/526)). The programme envisages the establishment of one code of practice for each of the issues governmental organization, siting, design, operation and quality assurance and also of about 50 safety guides between 1975 and 1980. These codes will contain the minimum requirements for the safety of the nuclear power stations, their systems and components. The guides will recommend methods to achieve the aims stated in the codes. It is the purpose of these IAEA activities to provide recommendations and guiding rules which may serve as standards for the assessment of the safety of nuclear power stations for all nations which may become participants in the peaceful use of nuclear energy within the next few years. (orig./AK) [de

  14. Thermal-hydraulic analysis code development and application to passive safety reactor at JAERI

    International Nuclear Information System (INIS)

    Araya, F.

    1995-01-01

    After a brief overview of safety assessment process, the author describes the LOCA analysis code system developed in JAERI. It comprises audit calculation code (WREM, WREM-J2, Japanese own code and BE codes (2D/3D, ICAP, ROSA). The codes are applied to development of Japanese passive safety reactor concept JPSR. Special attention is paid to the passive heat removal system and phenomena considered to occur under loss of heat sink event. Examples of LOCA analysis based on operation of JPSR for the cases of heat removal by upper RHR and heat removal from core to atmosphere are given. Experiments for multi-dimensional flow field in RPV and steam condensation in water pool are used for understanding the phenomena in passive safety reactors. The report is in a poster form only. 1 tab., 13 figs

  15. Sensitivity and uncertainty analyses applied to criticality safety validation, methods development. Volume 1

    International Nuclear Information System (INIS)

    Broadhead, B.L.; Hopper, C.M.; Childs, R.L.; Parks, C.V.

    1999-01-01

    This report presents the application of sensitivity and uncertainty (S/U) analysis methodologies to the code/data validation tasks of a criticality safety computational study. Sensitivity and uncertainty analysis methods were first developed for application to fast reactor studies in the 1970s. This work has revitalized and updated the available S/U computational capabilities such that they can be used as prototypic modules of the SCALE code system, which contains criticality analysis tools currently used by criticality safety practitioners. After complete development, simplified tools are expected to be released for general use. The S/U methods that are presented in this volume are designed to provide a formal means of establishing the range (or area) of applicability for criticality safety data validation studies. The development of parameters that are analogous to the standard trending parameters forms the key to the technique. These parameters are the D parameters, which represent the differences by group of sensitivity profiles, and the ck parameters, which are the correlation coefficients for the calculational uncertainties between systems; each set of parameters gives information relative to the similarity between pairs of selected systems, e.g., a critical experiment and a specific real-world system (the application)

  16. Safety code 19: recommended safety procedures for the selection, installation and use of x-ray diffraction equipment

    International Nuclear Information System (INIS)

    1984-01-01

    This document is one of a series of Safety Codes prepared by the Radiation Protection Bureau to set out requirements for the safe use of radiation emitting devices. The equipment and installation guidelines and safety procedures detailed in this Code are primarily for the instruction and guidance of persons employed in Federal Public Service Departments and Agencies, as well as those coming under the jurisdiction of the Canada Labour Code. This Safety Code is also intended to assist other users of X-ray diffraction equipment to select safe equipment and to install and use it so that the radiation hazard to the operator and other persons in its vicinity is negligible. It should be noted that facilities under provincial jurisdiction may be subject to requirements specified under provincial statutes. This Code supersedes Safety Code RPD-SC-7, entitled 'Requirements For Non-Medical X-Ray Equipment, Use and Installation', insofar as X-ray diffraction equipment is concerned, and it is intended to complement X-ray equipment design, construction and performance standards promulgated under the Radiation Emitting Devices Act

  17. The safety relief valve handbook design and use of process safety valves to ASME and International codes and standards

    CERN Document Server

    Hellemans, Marc

    2009-01-01

    The Safety Valve Handbook is a professional reference for design, process, instrumentation, plant and maintenance engineers who work with fluid flow and transportation systems in the process industries, which covers the chemical, oil and gas, water, paper and pulp, food and bio products and energy sectors. It meets the need of engineers who have responsibilities for specifying, installing, inspecting or maintaining safety valves and flow control systems. It will also be an important reference for process safety and loss prevention engineers, environmental engineers, and plant and process designers who need to understand the operation of safety valves in a wider equipment or plant design context. . No other publication is dedicated to safety valves or to the extensive codes and standards that govern their installation and use. A single source means users save time in searching for specific information about safety valves. . The Safety Valve Handbook contains all of the vital technical and standards informat...

  18. Validation of the containment code Sirius: interpretation of an explosion experiment on a scale model

    International Nuclear Information System (INIS)

    Blanchet, Y.; Obry, P.; Louvet, J.; Deshayes, M.; Phalip, C.

    1979-01-01

    The explicit 2-D axisymmetric Langrangian code SIRIUS, developed at the CEA/DRNR, Cadarache, deals with transient compressive flows in deformable primary tanks with more or less complex internal component geometries. This code has been subjected to a two-year intensive validation program on scale model experiments and a number of improvements have been incorporated. This paper presents a recent calculation of one of these experiments using the SIRIUS code, and the comparison with experimental results shows the encouraging possibilities of this Lagrangian code

  19. Reactor Safety Commission Code of Practice for Pressurized Water Reactors

    International Nuclear Information System (INIS)

    1990-01-01

    The Reactor Safety Commission of the Federal German Republic has summarized in the form of Official Guidelines the safety requirements which, in the Commission's view, have to be met in the design, construction and operation of a nuclear power station equipped with a pressurized water reactor. The Third Edition of the RSK Guidelines for pressurized water reactors dated 14.10.81. is a revised and expanded version of the Second Edition dated 24.1.79. The Reactor Safety Commission will with effect from October 1981 use these Guidelines in consultations on the siting of and safety concept for the installation approval of future pressurized water reactors and will assess these nuclear power stations during their erection in the light of these Guidelines. They have not however been immediately conceived for the adaptation of existing nuclear power stations, whether under construction or in operation. The scope of application of these Guidelines to such nuclear power stations will have to be examined for each individual case. The main aim of the Guidelines is to simplify the consultation process within the reactor Safety Commission and to provide early advice on the safety requirements considered necessary by the Commission. (author)

  20. Phase 1 Validation Testing and Simulation for the WEC-Sim Open Source Code

    Science.gov (United States)

    Ruehl, K.; Michelen, C.; Gunawan, B.; Bosma, B.; Simmons, A.; Lomonaco, P.

    2015-12-01

    WEC-Sim is an open source code to model wave energy converters performance in operational waves, developed by Sandia and NREL and funded by the US DOE. The code is a time-domain modeling tool developed in MATLAB/SIMULINK using the multibody dynamics solver SimMechanics, and solves the WEC's governing equations of motion using the Cummins time-domain impulse response formulation in 6 degrees of freedom. The WEC-Sim code has undergone verification through code-to-code comparisons; however validation of the code has been limited to publicly available experimental data sets. While these data sets provide preliminary code validation, the experimental tests were not explicitly designed for code validation, and as a result are limited in their ability to validate the full functionality of the WEC-Sim code. Therefore, dedicated physical model tests for WEC-Sim validation have been performed. This presentation provides an overview of the WEC-Sim validation experimental wave tank tests performed at the Oregon State University's Directional Wave Basin at Hinsdale Wave Research Laboratory. Phase 1 of experimental testing was focused on device characterization and completed in Fall 2015. Phase 2 is focused on WEC performance and scheduled for Winter 2015/2016. These experimental tests were designed explicitly to validate the performance of WEC-Sim code, and its new feature additions. Upon completion, the WEC-Sim validation data set will be made publicly available to the wave energy community. For the physical model test, a controllable model of a floating wave energy converter has been designed and constructed. The instrumentation includes state-of-the-art devices to measure pressure fields, motions in 6 DOF, multi-axial load cells, torque transducers, position transducers, and encoders. The model also incorporates a fully programmable Power-Take-Off system which can be used to generate or absorb wave energy. Numerical simulations of the experiments using WEC-Sim will be

  1. Utilization of the MCNP-3A code for criticality safety analysis

    International Nuclear Information System (INIS)

    Maragni, M.G.; Moreira, J.M.L.

    1996-01-01

    In the last decade, Brazil started to operate facilities for processing and storing uranium in different forms. The necessity of criticality safety analysis appeared in the design phase of the uranium pilot process plants and also in the licensing of transportation and storage of fissile materials. The 2-MW research reactor and the Angra I power plant also required criticality safety assessments because their spent-fuel storage was approaching full-capacity utilization. The criticality safety analysis in Brazil has been based on KENO IV code calculations, which present some difficulties for correct geometry representation. The MCNP-3A code is not reported to be used frequently for criticality safety analysis in Brazil, but its good geometry representation makes it a possible tool for treating problems of complex geometry. A set of benchmark tests was performed to verify its applicability for criticality safety analysis in Brazil. This paper presents several benchmark tests aimed at selecting a set of options available in the MCNP-3A code that would be adequate for criticality safety analysis. The MCNP-3A code is also compared with the KENO-IV code regarding its performance for criticality safety analysis

  2. International benchmark study of advanced thermal hydraulic safety analysis codes against measurements on IEA-R1 research reactor

    Energy Technology Data Exchange (ETDEWEB)

    Hainoun, A., E-mail: pscientific2@aec.org.sy [Atomic Energy Commission of Syria (AECS), Nuclear Engineering Department, P.O. Box 6091, Damascus (Syrian Arab Republic); Doval, A. [Nuclear Engineering Department, Av. Cmdt. Luis Piedrabuena 4950, C.P. 8400 S.C de Bariloche, Rio Negro (Argentina); Umbehaun, P. [Centro de Engenharia Nuclear – CEN, IPEN-CNEN/SP, Av. Lineu Prestes 2242-Cidade Universitaria, CEP-05508-000 São Paulo, SP (Brazil); Chatzidakis, S. [School of Nuclear Engineering, Purdue University, West Lafayette, IN 47907 (United States); Ghazi, N. [Atomic Energy Commission of Syria (AECS), Nuclear Engineering Department, P.O. Box 6091, Damascus (Syrian Arab Republic); Park, S. [Research Reactor Design and Engineering Division, Basic Science Project Operation Dept., Korea Atomic Energy Research Institute (Korea, Republic of); Mladin, M. [Institute for Nuclear Research, Campului Street No. 1, P.O. Box 78, 115400 Mioveni, Arges (Romania); Shokr, A. [Division of Nuclear Installation Safety, Research Reactor Safety Section, International Atomic Energy Agency, A-1400 Vienna (Austria)

    2014-12-15

    Highlights: • A set of advanced system thermal hydraulic codes are benchmarked against IFA of IEA-R1. • Comparative safety analysis of IEA-R1 reactor during LOFA by 7 working teams. • This work covers both experimental and calculation effort and presents new out findings on TH of RR that have not been reported before. • LOFA results discrepancies from 7% to 20% for coolant and peak clad temperatures are predicted conservatively. - Abstract: In the framework of the IAEA Coordination Research Project on “Innovative methods in research reactor analysis: Benchmark against experimental data on neutronics and thermal hydraulic computational methods and tools for operation and safety analysis of research reactors” the Brazilian research reactor IEA-R1 has been selected as reference facility to perform benchmark calculations for a set of thermal hydraulic codes being widely used by international teams in the field of research reactor (RR) deterministic safety analysis. The goal of the conducted benchmark is to demonstrate the application of innovative reactor analysis tools in the research reactor community, validation of the applied codes and application of the validated codes to perform comprehensive safety analysis of RR. The IEA-R1 is equipped with an Instrumented Fuel Assembly (IFA) which provided measurements for normal operation and loss of flow transient. The measurements comprised coolant and cladding temperatures, reactor power and flow rate. Temperatures are measured at three different radial and axial positions of IFA summing up to 12 measuring points in addition to the coolant inlet and outlet temperatures. The considered benchmark deals with the loss of reactor flow and the subsequent flow reversal from downward forced to upward natural circulation and presents therefore relevant phenomena for the RR safety analysis. The benchmark calculations were performed independently by the participating teams using different thermal hydraulic and safety

  3. Cross-Index to DOE-prescribed industrial safety codes and standards

    International Nuclear Information System (INIS)

    1980-01-01

    This Cross-Index volume is the 1980 compilation of detailed information from more than two hundred and ninety Department of Energy (DOE) prescribed or Occupational Health and Safety Administration (OSHA) referenced industrial safety codes and standards. The compilation of this material was conceived and initiated in 1973, and is revised yearly to provide information from current codes. Condensed data from individual code portions are listed according to reference code, section, paragraph, and page. Each code is given a two-digit reference code number or letter in the Contents section. This reference code provides ready identification of any code listed in the Cross-Index. The computerized information listings are on the left-hand portion of Cross-Index page; in order to the right of the listing are the reference code letters or numbers, the section, paragraph, and page of the referenced code containing expanded information on the individual listing. Simplified How to Use directions are listed. A glossary of letter initials/abbreviations for the organizations or documents, whose codes or standards are contained in this Cross-Index, is included

  4. Validation of SCALE code package on high performance neutron shields

    International Nuclear Information System (INIS)

    Bace, M.; Jecmenica, R.; Smuc, T.

    1999-01-01

    The shielding ability and other properties of new high performance neutron shielding materials from the KRAFTON series have been recently published. A comparison of the published experimental and MCNP results for the two materials of the KRAFTON series, with our own calculations has been done. Two control modules of the SCALE-4.4 code system have been used, one of them based on one dimensional radiation transport analysis (SAS1) and other based on the three dimensional Monte Carlo method (SAS3). The comparison of the calculated neutron dose equivalent rates shows a good agreement between experimental and calculated results for the KRAFTON-N2 material.. Our results indicate that the N2-M-N2 sandwich type is approximately 10% inferior as neutron shield to the KRAFTON-N2 material. All values of neutron dose equivalent obtained by SAS1 are approximately 25% lower in comparison with the SAS3 results, which indicates proportions of discrepancies introduced by one-dimensional geometry approximation.(author)

  5. Validation of nuclear criticality safety software and 27 energy group ENDF/B-IV cross sections. Revision 1

    International Nuclear Information System (INIS)

    Lee, B.L. Jr.; D'Aquila, D.M.

    1996-01-01

    The original validation report, POEF-T-3636, was documented in August 1994. The document was based on calculations that were executed during June through August 1992. The statistical analyses in Appendix C and Appendix D were completed in October 1993. This revision is written to clarify the margin of safety being used at Portsmouth for nuclear criticality safety calculations. This validation gives Portsmouth NCS personnel a basis for performing computerized KENO V.a calculations using the Lockheed Martin Nuclear Criticality Safety Software. The first portion of the document outlines basic information in regard to validation of NCSS using ENDF/B-IV 27-group cross sections on the IBM3090 at ORNL. A basic discussion of the NCSS system is provided, some discussion on the validation database and validation in general. Then follows a detailed description of the statistical analysis which was applied. The results of this validation indicate that the NCSS software may be used with confidence for criticality calculations at the Portsmouth Gaseous Diffusion Plant. For calculations of Portsmouth systems using the specified codes and systems covered by this validation, a maximum k eff including 2σ of 0.9605 or lower shall be considered as subcritical to ensure a calculational margin of safety of 0.02. The validation of NCSS on the IBM 3090 at ORNL was extended to include NCSS on the IBM 3090 at K-25

  6. Code on the safety of nuclear power plants: Quality assurance

    International Nuclear Information System (INIS)

    1988-01-01

    This revised Code provides the principles and objectives for the establishment and implementation of quality assurance programmes applied to both the overall and each of the constituent activities associated with a nuclear power plant project. The quality assurance principles enumerated in the present Code can be usefully applied to nuclear facilities other than nuclear power plants. The quality assurance programme encompasses: (1) the activities that are necessary to achieve the appropriate quality of the respective item or service; and (2) the activities that are necessary for verifying that the required quality is achieved and that objective evidence is produced to that effect. Quality assurance is an essential aspect of good management and the quality assurance programme is the main management tool for a disciplined approach to all activities affecting quality, including, where appropriate, verification that each task has been satisfactorily performed and that necessary corrective actions have been implemented. The principles and objectives provided by the Code are applicable by all those responsible for the nuclear power plant, by plant designers, suppliers, architect-engineers, plant constructors, plant operators and other organizations participating in activities affecting quality. The Code is a revision of the previous Code of Practice (1978) on the same subject of interest to regulatory bodies and experts in quality assurance for design, siting and operation of nuclear power plants. Contents: Definitions; 1. Introduction; 2. Quality assurance programmes; 3. Organization; 4. Document control; 5. Design control; 6. Procurement control; 7. Control of items; 8. Process control; 9. Inspection and test control; 10. Non-conformance control; 11. Corrective actions; 12, Records; 13. Audits

  7. R&D for Safety Codes and Standards: Materials and Components Compatibility

    Energy Technology Data Exchange (ETDEWEB)

    Somerday, Brian P. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); LaFleur, Chris [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Marchi, Chris San [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2015-08-01

    This project addresses the following technical barriers from the Safety, Codes and Standards section of the 2012 Fuel Cell Technologies Office Multi-Year Research, Development and Demonstration Plan (section 3.8): (A) Safety data and information: limited access and availability (F) Enabling national and international markets requires consistent RCS (G) Insufficient technical data to revise standards.

  8. Preliminary design of a small air loop for system analysis and validation of Cathare code

    International Nuclear Information System (INIS)

    Marchand, M.; Saez, M.; Tauveron, N.; Tenchine, D.; Germain, T.; Geffraye, G.; Ruby, G.P.

    2007-01-01

    The French Atomic Energy Commission (Cea) is carrying on the design of a Small Air Loop for System Analysis (SALSA), devoted to the study of gas cooled nuclear reactors behaviour in normal and incidental/accidental operating conditions. The reduced size of the SALSA components compared to a full-scale reactor and air as gaseous coolant instead of Helium will allow an easy management of the loop. The main purpose of SALSA will be the validation of the associated thermal hydraulic safety simulation codes, like CATHARE. The main goal of this paper is to present the methodology used to define the characteristics of the loop. In a first step, the study has been focused on a direct-cycle system for the SALSA loop with few global constraints using a similarity analysis to support the definition and design of the loop. Similarity requirements have been evaluated to determine the scale factors which have to be applied to the SALSA loop components. The preliminary conceptual design of the SALSA plant with a definition of each component has then be carried out. The whole plant has been modelled using the CATHARE code. Calculations of the SALSA steady-state in nominal conditions and of different plant transients in direct-cycle have been made. The first system results obtained on the global behaviour of the loop confirm that SALSA can be representative of a Gas-Cooled nuclear reactor with some minor design modifications. In a second step, the current prospects focus on the SALSA loop capability to reproduce correctly the heat transfer occurring in specific incidental situations. Heat decay removal by natural convection is a crucial point of interest. The first results show that the behaviour and the efficiency of the loop are strongly influenced by the definition of the main parameters for each component. A complete definition of SALSA is under progress. (authors)

  9. Validation of VHTRC calculation benchmark of critical experiment using the MCB code

    Directory of Open Access Journals (Sweden)

    Stanisz Przemysław

    2016-01-01

    Full Text Available The calculation benchmark problem Very High Temperature Reactor Critical (VHTR a pin-in-block type core critical assembly has been investigated with the Monte Carlo Burnup (MCB code in order to validate the latest version of Nuclear Data Library based on ENDF format. Executed benchmark has been made on the basis of VHTR benchmark available from the International Handbook of Evaluated Reactor Physics Benchmark Experiments. This benchmark is useful for verifying the discrepancies in keff values between various libraries and experimental values. This allows to improve accuracy of the neutron transport calculations that may help in designing the high performance commercial VHTRs. Almost all safety parameters depend on the accuracy of neutron transport calculation results that, in turn depend on the accuracy of nuclear data libraries. Thus, evaluation of the libraries applicability to VHTR modelling is one of the important subjects. We compared the numerical experiment results with experimental measurements using two versions of available nuclear data (ENDF-B-VII.1 and JEFF-3.2 prepared for required temperatures. Calculations have been performed with the MCB code which allows to obtain very precise representation of complex VHTR geometry, including the double heterogeneity of a fuel element. In this paper, together with impact of nuclear data, we discuss also the impact of different lattice modelling inside the fuel pins. The discrepancies of keff have been successfully observed and show good agreement with each other and with the experimental data within the 1 σ range of the experimental uncertainty. Because some propagated discrepancies observed, we proposed appropriate corrections in experimental constants which can improve the reactivity coefficient dependency. Obtained results confirm the accuracy of the new Nuclear Data Libraries.

  10. Code on the safety of nuclear research reactors: Design

    International Nuclear Information System (INIS)

    1992-01-01

    The main objective of this publication is to provide a safety basis for the design of a research reactor and for the assessment of the design. Another objective is to cover certain aspects related to regulatory supervision, siting and quality assurance, as far as these are related to activities for the design of a research reactor. These objectives are expressed in terms of requirements and recommendations for the design of research reactors. Emphasis is placed on the safety requirements that shall be met rather than on ways in which they can be met. The requirements and recommendations may form the foundation necessary for a Member State to develop specific regulations and safety criteria for its research reactor programme.

  11. Evaporation over sump surface in containment studies: code validation on TOSQAN tests

    International Nuclear Information System (INIS)

    Malet, J.; Gelain, T.; Degrees du Lou, O.; Daru, V.

    2011-01-01

    During the course of a severe accident in a Nuclear Power Plant, water can be collected in the sump containment through steam condensation on walls and spray systems activation. The objective of this paper is to present code validation on evaporative sump tests performed on the TOSQAN facility. The ASTEC-CPA code is used as a lumped-parameter code and specific user-defined-functions are developed for the TONUS-CFD code. The tests are air-steam tests, as well as tests with other non-condensable gases (He, CO 2 and SF 6 ) under steady and transient conditions. The results show a good agreement between codes and experiments, indicating a good behaviour of the sump models in both codes. (author)

  12. Validation of the transportation computer codes HIGHWAY, INTERLINE, RADTRAN 4, and RISKIND

    International Nuclear Information System (INIS)

    Maheras, S.J.; Pippen, H.K.

    1995-05-01

    The computer codes HIGHWAY, INTERLINE, RADTRAN 4, and RISKIND were used to estimate radiation doses from the transportation of radioactive material in the Department of Energy Programmatic Spent Nuclear Fuel Management and Idaho National Engineering Laboratory Environmental Restoration and Waste Management Programs Environmental Impact Statement. HIGHWAY and INTERLINE were used to estimate transportation routes for truck and rail shipments, respectively. RADTRAN 4 was used to estimate collective doses from incident-free transportation and the risk (probability x consequence) from transportation accidents. RISKIND was used to estimate incident-free radiation doses for maximally exposed individuals and the consequences from reasonably foreseeable transportation accidents. The purpose of this analysis is to validate the estimates made by these computer codes; critiques of the conceptual models used in RADTRAN 4 are also discussed. Validation is defined as ''the test and evaluation of the completed software to ensure compliance with software requirements.'' In this analysis, validation means that the differences between the estimates generated by these codes and independent observations are small (i.e., within the acceptance criterion established for the validation analysis). In some cases, the independent observations used in the validation were measurements; in other cases, the independent observations used in the validation analysis were generated using hand calculations. The results of the validation analyses performed for HIGHWAY, INTERLINE, RADTRAN 4, and RISKIND show that the differences between the estimates generated using the computer codes and independent observations were small. Based on the acceptance criterion established for the validation analyses, the codes yielded acceptable results; in all cases the estimates met the requirements for successful validation

  13. The integrated code system CASCADE-3D for advanced core design and safety analysis

    International Nuclear Information System (INIS)

    Neufert, A.; Van de Velde, A.

    1999-01-01

    The new program system CASCADE-3D (Core Analysis and Safety Codes for Advanced Design Evaluation) links some of Siemens advanced code packages for in-core fuel management and accident analysis: SAV95, PANBOX/COBRA and RELAP5. Consequently by using CASCADE-3D the potential of modern fuel assemblies and in-core fuel management strategies can be much better utilized because safety margins which had been reduced due to conservative methods are now predicted more accurately. By this innovative code system the customers can now take full advantage of the recent progress in fuel assembly design and in-core fuel management.(author)

  14. Code on the safety of nuclear research reactors: Operation

    International Nuclear Information System (INIS)

    1992-01-01

    The purpose of this publication is to provide the essential requirements and recommendations for the safe operation of research reactors, with emphasis on the supervisory and managerial aspects. However, the publication also provides some guidance and information on topics concerning all the organizations involved in operation. These objectives are expressed in terms of requirements and recommendations for the safe operation of research reactors. Emphasis is placed on the safety requirements that shall be met rather than on the ways in which they can be met. The requirements and recommendations may form the foundation necessary for a Member State to develop regulations and safety criteria for its research reactor programme.

  15. In-vessel core degradation code validation matrix

    International Nuclear Information System (INIS)

    Haste, T.J.; Adroguer, B.; Gauntt, R.O.; Martinez, J.A.; Ott, L.J.; Sugimoto, J.; Trambauer, K.

    1996-01-01

    The objective of the current Validation Matrix is to define a basic set of experiments, for which comparison of the measured and calculated parameters forms a basis for establishing the accuracy of test predictions, covering the full range of in-vessel core degradation phenomena expected in light water reactor severe accident transients. The scope of the review covers PWR and BWR designs of Western origin: the coverage of phenomena extends from the initial heat-up through to the introduction of melt into the lower plenum. Concerning fission product behaviour, the effect of core degradation on fission product release is considered. The report provides brief overviews of the main LWR severe accident sequences and of the dominant phenomena involved. The experimental database is summarised. These data are cross-referenced against a condensed set of the phenomena and test condition headings presented earlier, judging the results against a set of selection criteria and identifying key tests of particular value. The main conclusions and recommendations are listed. (K.A.)

  16. Preliminary Validation of the MATRA-LMR Code Using Existing Sodium-Cooled Experimental Data

    International Nuclear Information System (INIS)

    Choi, Sun Rock; Kim, Sangji

    2014-01-01

    The main objective of the SFR prototype plant is to verify TRU metal fuel performance, reactor operation, and transmutation ability of high-level wastes. The core thermal-hydraulic design is used to ensure the safe fuel performance during the whole plant operation. The fuel design limit is highly dependent on both the maximum cladding temperature and the uncertainties of the design parameters. Therefore, an accurate temperature calculation in each subassembly is highly important to assure a safe and reliable operation of the reactor systems. The current core thermalhydraulic design is mainly performed using the SLTHEN (Steady-State LMR Thermal-Hydraulic Analysis Code Based on ENERGY Model) code, which has been already validated using the existing sodium-cooled experimental data. In addition to the SLTHEN code, a detailed analysis is performed using the MATRA-LMR (Multichannel Analyzer for Transient and steady-state in Rod Array-Liquid Metal Reactor) code. In this work, the MATRA-LMR code is validated for a single subassembly evaluation using the previous experimental data. The MATRA-LMR code has been validated using existing sodium-cooled experimental data. The results demonstrate that the design code appropriately predicts the temperature distributions compared with the experimental values. Major differences are observed in the experiments with the large pin number due to the radial-wise mixing difference

  17. A proposed framework for computational fluid dynamics code calibration/validation

    International Nuclear Information System (INIS)

    Oberkampf, W.L.

    1993-01-01

    The paper reviews the terminology and methodology that have been introduced during the last several years for building confidence n the predictions from Computational Fluid Dynamics (CID) codes. Code validation terminology developed for nuclear reactor analyses and aerospace applications is reviewed and evaluated. Currently used terminology such as ''calibrated code,'' ''validated code,'' and a ''validation experiment'' is discussed along with the shortcomings and criticisms of these terms. A new framework is proposed for building confidence in CFD code predictions that overcomes some of the difficulties of past procedures and delineates the causes of uncertainty in CFD predictions. Building on previous work, new definitions of code verification and calibration are proposed. These definitions provide more specific requirements for the knowledge level of the flow physics involved and the solution accuracy of the given partial differential equations. As part of the proposed framework, categories are also proposed for flow physics research, flow modeling research, and the application of numerical predictions. The contributions of physical experiments, analytical solutions, and other numerical solutions are discussed, showing that each should be designed to achieve a distinctively separate purpose in building confidence in accuracy of CFD predictions. A number of examples are given for each approach to suggest methods for obtaining the highest value for CFD code quality assurance

  18. Validation of Fuel Performance Uncertainty for RIA Safety Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Park, Nam-Gyu; Yoo, Jong-Sung; Jung, Yil-Sup [KEPCO Nuclear Fuel Co., Daejeon (Korea, Republic of)

    2016-10-15

    To achieve this the computer code performance has to be validated based on the experimental results. And for the uncertainty quantification, important uncertainty parameters need to be selected, and combined uncertainty has to be evaluated with an acceptable statistical treatment. And important uncertainty parameters to the rod performance such as fuel enthalpy, fission gas release, cladding hoop strain etc. were chosen through the rigorous sensitivity studies. And their validity has been assessed by utilizing the experimental results, which were tested in CABRI and NSRR. Analysis results revealed that several tested rods were not bounded within combined fuel performance uncertainty. Assessment of fuel performance with an extended fuel power uncertainty on tested rods in NSRR and CABRI has been done. Analysis results showed that several tested rods were not bounded within calculated fuel performance uncertainty. This implies that the currently considered uncertainty range of the parameters is not enough to cover the fuel performance sufficiently.

  19. Development of NPP Safety Requirements into Kenya's Grid Codes

    Energy Technology Data Exchange (ETDEWEB)

    Ndirangu, Nguni James; Koo, Chang Choong [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

    2015-10-15

    As presently drafted, Kenya's grid codes do not contain any NPP requirements. Through case studies of selected grid codes, this paper will study frequency, voltage and fault ride through requirements for NPP connection and operation, and offer recommendation of how these requirements can be incorporated in the Kenya's grid codes. Voltage and frequency excursions in Kenya's grid are notably frequently outside the generic requirement and the values observed by the German and UK grid codes. Kenya's grid codes require continuous operation for ±10% of nominal voltage and 45.0 to 52Hz on the grid which poses safety issues for an NPP. Considering stringent NPP connection to grid and operational safety requirements, and the importance of the TSO to NPP safety, more elaborate requirements need to be documented in the Kenya's grid codes. UK and Germany have a history of meeting high standards of nuclear safety and it is therefore recommended that format like the one in Table 1 to 3 should be adopted. Kenya's Grid code considering NPP should have: • Strict rules for voltage variation, that is, -5% to +10% of the nominal voltage • Strict rules for frequency variation, that is, 48Hz to 52Hz of the nominal frequencyand.

  20. Development of NPP Safety Requirements into Kenya's Grid Codes

    International Nuclear Information System (INIS)

    Ndirangu, Nguni James; Koo, Chang Choong

    2015-01-01

    As presently drafted, Kenya's grid codes do not contain any NPP requirements. Through case studies of selected grid codes, this paper will study frequency, voltage and fault ride through requirements for NPP connection and operation, and offer recommendation of how these requirements can be incorporated in the Kenya's grid codes. Voltage and frequency excursions in Kenya's grid are notably frequently outside the generic requirement and the values observed by the German and UK grid codes. Kenya's grid codes require continuous operation for ±10% of nominal voltage and 45.0 to 52Hz on the grid which poses safety issues for an NPP. Considering stringent NPP connection to grid and operational safety requirements, and the importance of the TSO to NPP safety, more elaborate requirements need to be documented in the Kenya's grid codes. UK and Germany have a history of meeting high standards of nuclear safety and it is therefore recommended that format like the one in Table 1 to 3 should be adopted. Kenya's Grid code considering NPP should have: • Strict rules for voltage variation, that is, -5% to +10% of the nominal voltage • Strict rules for frequency variation, that is, 48Hz to 52Hz of the nominal frequencyand

  1. Assessment of heat transfer correlations for supercritical water in the frame of best-estimate code validation

    International Nuclear Information System (INIS)

    Jaeger, Wadim; Espinoza, Victor H. Sanchez; Schneider, Niko; Hurtado, Antonio

    2009-01-01

    Within the frame of the Generation IV international forum six innovative reactor concepts are the subject of comprehensive investigations. In some projects supercritical water will be considered as coolant, moderator (as for the High Performance Light Water Reactor) or secondary working fluid (one possible option for Liquid Metal-cooled Fast Reactors). Supercritical water is characterized by a pronounced change of the thermo-physical properties when crossing the pseudo-critical line, which goes hand in hand with a change in the heat transfer (HT) behavior. Hence, it is essential to estimate, in a proper way, the heat-transfer coefficient and subsequently the wall temperature. The scope of this paper is to present and discuss the activities at the Institute for Reactor Safety (IRS) related to the implementation of correlations for wall-to-fluid HT at supercritical conditions in Best-Estimate codes like TRACE as well as its validation. It is important to validate TRACE before applying it to safety analyses of HPLWR or of other reactor systems. In the past 3 decades various experiments have been performed all over the world to reveal the peculiarities of wall-to-fluid HT at supercritical conditions. Several different heat transfer phenomena such as HT enhancement (due to higher Prandtl numbers in the vicinity of the pseudo-critical point) or HT deterioration (due to strong property variations) were observed. Since TRACE is a component based system code with a finite volume method the resolution capabilities are limited and not all physical phenomena can be modeled properly. But Best -Estimate system codes are nowadays the preferred option for safety related investigations of full plants or other integral systems. Thus, the increase of the confidence in such codes is of high priority. In this paper, the post-test analysis of experiments with supercritical parameters will be presented. For that reason various correlations for the HT, which considers the characteristics

  2. Demonstration study on shielding safety analysis code. 7

    Energy Technology Data Exchange (ETDEWEB)

    Sawamura, Sadashi [Hokkaido Univ., Sapporo (Japan). Faculty of Engineering

    2000-03-01

    Dose evaluation for direct radiation and skyshine from nuclear fuel facilities is one of the environment evaluation items. This evaluation is carried out by using some shielding calculation codes. Because of extremely few benchmark data of skyshine, the calculation has to be performed very conservatively. Therefore, the benchmark data of skyshine and the well-investigated code for skyshine would be necessary to carry out the rational evaluation of nuclear facilities. The purpose of this study is to obtain the benchmark data of skyshine and to investigate the calculation code for skyshine. In this fiscal year, the followings are investigated; (1) To improve the detection sensitivity of pulse neutron measurement, two neutron detectors and some electronic circuits are added to the system constructed last year. (2) To estimate the neutron dose at the distant point from the facility instead of the commercialized rem-counter, a {sup 3}He detector with paraffin moderator is equipped to the system. (3) Using the new detection system, the skyshine of neutrons from 45 MeV LINAC facility was measured in the distance up to 300 m. The results show that the time structure of pulsed neutrons almost disappears at the further points than 150 m. (4) In the distance from 90 m to 300 m ordinal total counting method without gate pulse are applied to detect the neutrons. (5) The experimental results of space dependency up to 300 m is fitted fairly well by the Gui's response function. (author)

  3. A proposed methodology for computational fluid dynamics code verification, calibration, and validation

    Science.gov (United States)

    Aeschliman, D. P.; Oberkampf, W. L.; Blottner, F. G.

    Verification, calibration, and validation (VCV) of Computational Fluid Dynamics (CFD) codes is an essential element of the code development process. The exact manner in which code VCV activities are planned and conducted, however, is critically important. It is suggested that the way in which code validation, in particular, is often conducted--by comparison to published experimental data obtained for other purposes--is in general difficult and unsatisfactory, and that a different approach is required. This paper describes a proposed methodology for CFD code VCV that meets the technical requirements and is philosophically consistent with code development needs. The proposed methodology stresses teamwork and cooperation between code developers and experimentalists throughout the VCV process, and takes advantage of certain synergisms between CFD and experiment. A novel approach to uncertainty analysis is described which can both distinguish between and quantify various types of experimental error, and whose attributes are used to help define an appropriate experimental design for code VCV experiments. The methodology is demonstrated with an example of laminar, hypersonic, near perfect gas, 3-dimensional flow over a sliced sphere/cone of varying geometrical complexity.

  4. An approach to verification and validation of MHD codes for fusion applications

    Energy Technology Data Exchange (ETDEWEB)

    Smolentsev, S., E-mail: sergey@fusion.ucla.edu [University of California, Los Angeles (United States); Badia, S. [Centre Internacional de Mètodes Numèrics en Enginyeria, Barcelona (Spain); Universitat Politècnica de Catalunya – Barcelona Tech (Spain); Bhattacharyay, R. [Institute for Plasma Research, Gandhinagar, Gujarat (India); Bühler, L. [Karlsruhe Institute of Technology (Germany); Chen, L. [University of Chinese Academy of Sciences, Beijing (China); Huang, Q. [Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui (China); Jin, H.-G. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Krasnov, D. [Technische Universität Ilmenau (Germany); Lee, D.-W. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Mas de les Valls, E. [Centre Internacional de Mètodes Numèrics en Enginyeria, Barcelona (Spain); Universitat Politècnica de Catalunya – Barcelona Tech (Spain); Mistrangelo, C. [Karlsruhe Institute of Technology (Germany); Munipalli, R. [HyPerComp, Westlake Village (United States); Ni, M.-J. [University of Chinese Academy of Sciences, Beijing (China); Pashkevich, D. [St. Petersburg State Polytechnical University (Russian Federation); Patel, A. [Universitat Politècnica de Catalunya – Barcelona Tech (Spain); Pulugundla, G. [University of California, Los Angeles (United States); Satyamurthy, P. [Bhabha Atomic Research Center (India); Snegirev, A. [St. Petersburg State Polytechnical University (Russian Federation); Sviridov, V. [Moscow Power Engineering Institute (Russian Federation); Swain, P. [Bhabha Atomic Research Center (India); and others

    2015-11-15

    Highlights: • Review of status of MHD codes for fusion applications. • Selection of five benchmark problems. • Guidance for verification and validation of MHD codes for fusion applications. - Abstract: We propose a new activity on verification and validation (V&V) of MHD codes presently employed by the fusion community as a predictive capability tool for liquid metal cooling applications, such as liquid metal blankets. The important steps in the development of MHD codes starting from the 1970s are outlined first and then basic MHD codes, which are currently in use by designers of liquid breeder blankets, are reviewed. A benchmark database of five problems has been proposed to cover a wide range of MHD flows from laminar fully developed to turbulent flows, which are of interest for fusion applications: (A) 2D fully developed laminar steady MHD flow, (B) 3D laminar, steady developing MHD flow in a non-uniform magnetic field, (C) quasi-two-dimensional MHD turbulent flow, (D) 3D turbulent MHD flow, and (E) MHD flow with heat transfer (buoyant convection). Finally, we introduce important details of the proposed activities, such as basic V&V rules and schedule. The main goal of the present paper is to help in establishing an efficient V&V framework and to initiate benchmarking among interested parties. The comparison results computed by the codes against analytical solutions and trusted experimental and numerical data as well as code-to-code comparisons will be presented and analyzed in companion paper/papers.

  5. Establishment of joint application system of safety analysis codes between Korea and Vietnam

    International Nuclear Information System (INIS)

    Chung, Bub Dong; Kim, Kyung Doo; Park, Cheol; Bae, Sung Won; Baek, Won Pil; Song, Cheol hwa; Jeong, Jae Jun; Lee, Seung Wook; Hwang, Moon Kyu; Lee, Chang Sup

    2011-04-01

    The following KAERI-VAEI collaboration works have been performed during the 2 year project ('09.4∼'11.4). 1) On the job training of Vietnam code users(1st training for 4 VAEI staff-3 months. 2nd training for 3 VAEI staff- 3 month), 2) Lecture of nuclear safety analysis (30 hrs basic course and 30 hrs advanced course), 3) Review of safety analysis method (IAEA safety concept and requirements), 4) Collaborative assessment of safety analysis code MARS (13 conceptual problem, 2 separate effect test problem, 1 integral effect test problem), 5) Input deck preparation of standard PWR (Preparation of APR1400 input deck and safety analysis of DBA). VAEI staffs have been familiarized to Korean PWR safety assessment technology through the collaboration assessment work using a computer code developed in Korea. The lectures for Vietnamese research will be contributed to the utilization and cultivation of Korean safety technology. The collaborated assessment works will be used for the establishment of MARS based safety analysis system which is independent from US safety assessment system

  6. Establishment of joint application system of safety analysis codes between Korea and Vietnam

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Bub Dong; Kim, Kyung Doo; Park, Cheol; Bae, Sung Won; Baek, Won Pil; Song, Cheol hwa; Jeong, Jae Jun; Lee, Seung Wook; Hwang, Moon Kyu; Lee, Chang Sup [KAERI, Daejeon (Korea, Republic of)

    2011-04-15

    The following KAERI-VAEI collaboration works have been performed during the 2 year project ('09.4{approx}'11.4). 1) On the job training of Vietnam code users(1st training for 4 VAEI staff-3 months. 2nd training for 3 VAEI staff- 3 month), 2) Lecture of nuclear safety analysis (30 hrs basic course and 30 hrs advanced course), 3) Review of safety analysis method (IAEA safety concept and requirements), 4) Collaborative assessment of safety analysis code MARS (13 conceptual problem, 2 separate effect test problem, 1 integral effect test problem), 5) Input deck preparation of standard PWR (Preparation of APR1400 input deck and safety analysis of DBA). VAEI staffs have been familiarized to Korean PWR safety assessment technology through the collaboration assessment work using a computer code developed in Korea. The lectures for Vietnamese research will be contributed to the utilization and cultivation of Korean safety technology. The collaborated assessment works will be used for the establishment of MARS based safety analysis system which is independent from US safety assessment system

  7. Secure Coding for Safety I and C Systems on Nuclear Power Plants

    International Nuclear Information System (INIS)

    Kim, Y. M.; Park, H. S.; Kim, T. H.

    2015-01-01

    This paper addresses secure coding technologies which can reduce the software vulnerabilities and provides secure coding application guidelines for nuclear safety I and C systems. The use of digital equipment may improve their reliability and reduce maintenance costs. But, the design characteristics of nuclear I and C systems are becoming more complex and the possibility of cyber-attacks using software vulnerabilities has been increased. Software defects, bugs and logic flaws have been consistently the primary causes of software vulnerabilities which can introduce security vulnerabilities. In this study, we described a applying methods for secure coding which can reduce the software vulnerabilities. Software defects lists, countermeasures for each defect and coding rules can be applied properly depending on target system's condition. We expect that the results of this study can help developing the secure coding guidelines and significantly reducing or eliminating vulnerabilities in nuclear safety I and C software

  8. Secure Coding for Safety I and C Systems on Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Y. M.; Park, H. S. [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of); Kim, T. H. [Formal Works Inc., Seoul (Korea, Republic of)

    2015-10-15

    This paper addresses secure coding technologies which can reduce the software vulnerabilities and provides secure coding application guidelines for nuclear safety I and C systems. The use of digital equipment may improve their reliability and reduce maintenance costs. But, the design characteristics of nuclear I and C systems are becoming more complex and the possibility of cyber-attacks using software vulnerabilities has been increased. Software defects, bugs and logic flaws have been consistently the primary causes of software vulnerabilities which can introduce security vulnerabilities. In this study, we described a applying methods for secure coding which can reduce the software vulnerabilities. Software defects lists, countermeasures for each defect and coding rules can be applied properly depending on target system's condition. We expect that the results of this study can help developing the secure coding guidelines and significantly reducing or eliminating vulnerabilities in nuclear safety I and C software.

  9. San Onofre PWR Data for Code Validation of MOX Fuel Depletion Analyses - Revision 1

    International Nuclear Information System (INIS)

    Hermann, O.W.

    2000-01-01

    The isotopic composition of mixed-oxide fuel (fabricated with both uranium and plutonium isotopes) discharged from reactors is of interest to the Fissile Material Disposition Program. The validation of depletion codes used to predict isotopic compositions of MOX fuel, similar to studies concerning uranium-only fueled reactors, thus, is very important. The EEI-Westinghouse Plutonium Recycle Demonstration Program was conducted to examine the use of MOX fuel in the San Onofre PWR, Unit I, during cycles 2 and 3. The data, usually required as input to depletion codes, either one-dimensional or lattice codes, were taken from various sources and compiled into this report. Where data were either lacking or determined inadequate, the appropriate data were supplied from other references. The scope of the reactor operations and design data, in addition to the isotopic analyses, was considered to be of sufficient quality for depletion code validation

  10. The KNICS approach for verification and validation of safety software

    International Nuclear Information System (INIS)

    Cha, Kyung Ho; Sohn, Han Seong; Lee, Jang Soo; Kim, Jang Yeol; Cheon, Se Woo; Lee, Young Joon; Hwang, In Koo; Kwon, Kee Choon

    2003-01-01

    This paper presents verification and validation (VV) to be approached for safety software of POSAFE-Q Programmable Logic Controller (PLC) prototype and Plant Protection System (PPS) prototype, which consists of Reactor Protection System (RPS) and Engineered Safety Features-Component Control System (ESF-CCS) in development of Korea Nuclear Instrumentation and Control System (KNICS). The SVV criteria and requirements are selected from IEEE Std. 7-4.3.2, IEEE Std. 1012, IEEE Std. 1028 and BTP-14, and they have been considered for acceptance framework to be provided within SVV procedures. SVV techniques, including Review and Inspection (R and I), Formal Verification and Theorem Proving, and Automated Testing, are applied for safety software and automated SVV tools supports SVV tasks. Software Inspection Support and Requirement Traceability (SIS-RT) supports R and I and traceability analysis, a New Symbolic Model Verifier (NuSMV), Statemate MAGNUM (STM) ModelCertifier, and Prototype Verification System (PVS) are used for formal verification, and McCabe and Cantata++ are utilized for static and dynamic software testing. In addition, dedication of Commercial-Off-The-Shelf (COTS) software and firmware, Software Safety Analysis (SSA) and evaluation of Software Configuration Management (SCM) are being performed for the PPS prototype in the software requirements phase

  11. MARS-KS code validation activity through the atlas domestic standard problem

    International Nuclear Information System (INIS)

    Choi, K. Y.; Kim, Y. S.; Kang, K. H.; Park, H. S.; Cho, S.

    2012-01-01

    The 2 nd Domestic Standard Problem (DSP-02) exercise using the ATLAS integral effect test data was executed to transfer the integral effect test data to domestic nuclear industries and to contribute to improving the safety analysis methodology for PWRs. A small break loss of coolant accident of a 6-inch break at the cold leg was determined as a target scenario by considering its technical importance and by incorporating interests from participants. Ten calculation results using MARS-KS code were collected, major prediction results were described qualitatively and code prediction accuracy was assessed quantitatively using the FFTBM. In addition, special code assessment activities were carried out to find out the area where the model improvement is required in the MARS-KS code. The lessons from this DSP-02 and recommendations to code developers are described in this paper. (authors)

  12. MKENO-DAR: a direct angular representation Monte Carlo code for criticality safety analysis

    International Nuclear Information System (INIS)

    Naito, Yoshitaka; Komuro, Yuichi; Tsunoo, Yukiyasu; Nakayama, Mitsuo.

    1984-03-01

    Improving the Monte Carlo code MULTI-KENO, the MKENO-DAR (Direct Angular Representation) code has been developed for criticality safety analysis in detail. A function was added to MULTI-KENO for representing anisotropic scattering strictly. With this function, the scattering angle of neutron is determined not by the average scattering angle μ-bar of the Pl Legendre polynomial but by the random work operation using probability distribution function produced with the higher order Legendre polynomials. This code is avilable for the FACOM-M380 computer. This report is a computer code manual for MKENO-DAR. (author)

  13. LISA. A code for safety assessment in nuclear waste disposals program description and user guide

    International Nuclear Information System (INIS)

    Saltelli, A.; Bertozzi, G.; Stanners, D.A.

    1984-01-01

    The code LISA (Long term Isolation Safety Assessment), developed at the Joint Research Centre, Ispra is a useful tool in the analysis of the hazard due to the disposal of nuclear waste in geological formations. The risk linked to preestablished release scenarios is assessed by the code in terms of dose rate to a maximum exposed individual. The various submodels in the code simulate the system of barriers -both natural and man made- which are interposed between the contaminants and man. After a description of the code features a guide for the user is supplied and then a test case is presented

  14. Pre-engineering Spaceflight Validation of Environmental Models and the 2005 HZETRN Simulation Code

    Science.gov (United States)

    Nealy, John E.; Cucinotta, Francis A.; Wilson, John W.; Badavi, Francis F.; Dachev, Ts. P.; Tomov, B. T.; Walker, Steven A.; DeAngelis, Giovanni; Blattnig, Steve R.; Atwell, William

    2006-01-01

    The HZETRN code has been identified by NASA for engineering design in the next phase of space exploration highlighting a return to the Moon in preparation for a Mars mission. In response, a new series of algorithms beginning with 2005 HZETRN, will be issued by correcting some prior limitations and improving control of propagated errors along with established code verification processes. Code validation processes will use new/improved low Earth orbit (LEO) environmental models with a recently improved International Space Station (ISS) shield model to validate computational models and procedures using measured data aboard ISS. These validated models will provide a basis for flight-testing the designs of future space vehicles and systems of the Constellation program in the LEO environment.

  15. Validation and application of help code used for design and review of cover of low and intermediate level radioactive waste disposal in near-surface facilities

    International Nuclear Information System (INIS)

    Fan Zhiwen; Gu Cunli; Zhang Jinsheng; Liu Xiuzhen

    1996-01-01

    The authors describes validation and application of HELP code used by the United States Environmental Protective Agency for design and review of cover of low and intermediate level radioactive waste disposal in near-surface facilities. The HELP code was validated using data of field aerated moisture movement test by China Institute for Radiation Protection. The results show that simulation of HELP code is reasonable. Effects of surface layer thickness and surface treatment on moisture distribution in a cover was simulated with HELP code in the conditions of south-west China. The simulation results demonstrated that surface plantation of a cover plays very important role in moisture distribution in the cover. Special attention should be paid in cover design. In humid area, radioactive waste disposal safety should take full consideration with functions of chemical barrier. It was recommended that engineering economy should be added in future cover research so as to achieve optimization of cover design

  16. Application of CFD Codes in Nuclear Reactor Safety Analysis

    Directory of Open Access Journals (Sweden)

    T. Höhne

    2010-01-01

    Full Text Available Computational Fluid Dynamics (CFD is increasingly being used in nuclear reactor safety (NRS analyses as a tool that enables safety relevant phenomena occurring in the reactor coolant system to be described in more detail. Numerical investigations on single phase coolant mixing in Pressurised Water Reactors (PWR have been performed at the FZD for almost a decade. The work is aimed at describing the mixing phenomena relevant for both safety analysis, particularly in steam line break and boron dilution scenarios, and mixing phenomena of interest for economical operation and the structural integrity. For the experimental investigation of horizontal two phase flows, different non pressurized channels and the TOPFLOW Hot Leg model in a pressure chamber was build and simulated with ANSYS CFX. In a common project between the University of Applied Sciences Zittau/Görlitz and FZD the behaviour of insulation material released by a LOCA released into the containment and might compromise the long term emergency cooling systems is investigated. Moreover, the actual capability of CFD is shown to contribute to fuel rod bundle design with a good CHF performance.

  17. Validation study of safety assessment model for radioactive waste disposal

    Energy Technology Data Exchange (ETDEWEB)

    Munakata, Masahiro; Takeda, Seiji; Kimura, Hideo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-12-01

    The JAERI-AECL collaboration research program has been conducted to validate a groundwater flow and radionuclide transport models for safety assessment. JAERI have developed a geostatistical model for radionuclide transport through a heterogeneous geological media and verify using experimental results of field tracer tests. The simulated tracer plumes explain favorably the experimental tracer plumes. A regional groundwater flow and transport model using site-scale parameter obtained from tracer tests have been verified by comparing simulation results with observation ones of natural environmental tracer. (author)

  18. Validation of the U.S. NRC coupled code system TRITON/TRACE/PARCS with the special power excursion reactor test III (SPERT III)

    Energy Technology Data Exchange (ETDEWEB)

    Wang, R. C.; Xu, Y.; Downar, T. [Dept. of Nuclear Engineering and Radiological Sciences, Univ. of Michigan, Ann Arbor, MI 48104 (United States); Hudson, N. [RES Div., U.S. NRC, Rockville, MD (United States)

    2012-07-01

    The Special Power Excursion Reactor Test III (SPERT III) was a series of reactivity insertion experiments conducted in the 1950's. This paper describes the validation of the U.S. NRC Coupled Code system TRITON/PARCS/TRACE to simulate reactivity insertion accidents (RIA) by using several of the SPERT III tests. The work here used the SPERT III E-core configuration tests in which the RIA was initiated by ejecting a control rod. The resulting super-prompt reactivity excursion and negative reactivity feedback produced the familiar bell shaped power increase and decrease. The energy deposition during such a power peak has important safety consequences and provides validation basis for core coupled multi-physics codes. The transients of five separate tests are used to benchmark the PARCS/TRACE coupled code. The models were thoroughly validated using the original experiment documentation. (authors)

  19. Computer codes in nuclear safety, radiation transport and dosimetry

    International Nuclear Information System (INIS)

    Bordy, J.M.; Kodeli, I.; Menard, St.; Bouchet, J.L.; Renard, F.; Martin, E.; Blazy, L.; Voros, S.; Bochud, F.; Laedermann, J.P.; Beaugelin, K.; Makovicka, L.; Quiot, A.; Vermeersch, F.; Roche, H.; Perrin, M.C.; Laye, F.; Bardies, M.; Struelens, L.; Vanhavere, F.; Gschwind, R.; Fernandez, F.; Quesne, B.; Fritsch, P.; Lamart, St.; Crovisier, Ph.; Leservot, A.; Antoni, R.; Huet, Ch.; Thiam, Ch.; Donadille, L.; Monfort, M.; Diop, Ch.; Ricard, M.

    2006-01-01

    The purpose of this conference was to describe the present state of computer codes dedicated to radiation transport or radiation source assessment or dosimetry. The presentations have been parted into 2 sessions: 1) methodology and 2) uses in industrial or medical or research domains. It appears that 2 different calculation strategies are prevailing, both are based on preliminary Monte-Carlo calculations with data storage. First, quick simulations made from a database of particle histories built though a previous Monte-Carlo simulation and secondly, a neuronal approach involving a learning platform generated through a previous Monte-Carlo simulation. This document gathers the slides of the presentations

  20. Integral test facilities for validation of the performance of passive safety systems and natural circulation

    International Nuclear Information System (INIS)

    Choi, J. H.

    2010-10-01

    Passive safety systems are becoming an important component in advanced reactor designs. This has led to an international interest in examining natural circulation phenomena as this may play an important role in the operation of these passive safety systems. Understanding reactor system behaviour is a challenging process due to the complex interactions between components and associated phenomena. Properly scaled integral test facilities can be used to explore these complex interactions. In addition, system analysis computer codes can be used as predictive tools in understanding the complex reactor system behaviour. However, before the application of system analysis computer codes for reactor design, it is capability in making predictions needs to be validated against the experimental data from a properly scaled integral test facility. The IAEA has organized a coordinated research project (CRP) on natural circulation phenomena, modeling and reliability of passive systems that utilize natural circulation. This paper is a part of research results from this CRP and describes representative international integral test facilities that can be used for data collection for reactor types in which natural circulation may play an important role. Example experiments were described along with the analyses of these example cases in order to examine the ability of system codes to model the phenomena that are occurring in the test facilities. (Author)

  1. Safety related investigations of the VVER-1000 reactor type by the coupled code system TRACE/PARCS

    International Nuclear Information System (INIS)

    Jaeger, Wadim; Lischke, Wolfgang; Sanchez Espinoza, Victor Hugo

    2007-01-01

    This study was performed at the Institute of Reactor Safety at the Research Center Karlsruhe. It is embedded in the ongoing investigations of the international code application and maintenance program (CAMP) for qualification and validation of system codes like TRACE [1] and PARCS [2]. The predestinated reactor type for the validation of these two codes was the Russian designed VVER-1000 because the OECD/NEA VVER-1000 Coolant Transient Benchmark Phase 2 [3] includes detailed information of the Bulgarian nuclear power plant (NPP) Kozloduy unit 6. The posttest-investigations of a coolant mixing experiment have shown that the predicted parameters (coolant temperature, pressure drop, etc.) are in good agreement to the measured data. The coolant mixing pattern especially in the downcomer has been also reproduced quiet well by TRACE. The coupled code system TRACE/PARCS which was applied on a postulated main steam line break (MSLB) provides good results compared to reference values and the ones of other participants of the benchmark. It can be pointed out that the developed three-dimensional nodalisation of the reactor pressure vessel (RPV) is appropriate for the description of transients where the thermal-hydraulics and the neutronics are strongly linked. (author)

  2. Sizing and scaling requirements of a large-scale physical model for code validation

    International Nuclear Information System (INIS)

    Khaleel, R.; Legore, T.

    1990-01-01

    Model validation is an important consideration in application of a code for performance assessment and therefore in assessing the long-term behavior of the engineered and natural barriers of a geologic repository. Scaling considerations relevant to porous media flow are reviewed. An analysis approach is presented for determining the sizing requirements of a large-scale, hydrology physical model. The physical model will be used to validate performance assessment codes that evaluate the long-term behavior of the repository isolation system. Numerical simulation results for sizing requirements are presented for a porous medium model in which the media properties are spatially uncorrelated

  3. Nuclear Energy Advanced Modeling and Simulation (NEAMS) Waste Integrated Performance and Safety Codes (IPSC) : FY10 development and integration.

    Energy Technology Data Exchange (ETDEWEB)

    Criscenti, Louise Jacqueline; Sassani, David Carl; Arguello, Jose Guadalupe, Jr.; Dewers, Thomas A.; Bouchard, Julie F.; Edwards, Harold Carter; Freeze, Geoffrey A.; Wang, Yifeng; Schultz, Peter Andrew

    2011-02-01

    This report describes the progress in fiscal year 2010 in developing the Waste Integrated Performance and Safety Codes (IPSC) in support of the U.S. Department of Energy (DOE) Office of Nuclear Energy Advanced Modeling and Simulation (NEAMS) Campaign. The goal of the Waste IPSC is to develop an integrated suite of computational modeling and simulation capabilities to quantitatively assess the long-term performance of waste forms in the engineered and geologic environments of a radioactive waste storage or disposal system. The Waste IPSC will provide this simulation capability (1) for a range of disposal concepts, waste form types, engineered repository designs, and geologic settings, (2) for a range of time scales and distances, (3) with appropriate consideration of the inherent uncertainties, and (4) in accordance with robust verification, validation, and software quality requirements. Waste IPSC activities in fiscal year 2010 focused on specifying a challenge problem to demonstrate proof of concept, developing a verification and validation plan, and performing an initial gap analyses to identify candidate codes and tools to support the development and integration of the Waste IPSC. The current Waste IPSC strategy is to acquire and integrate the necessary Waste IPSC capabilities wherever feasible, and develop only those capabilities that cannot be acquired or suitably integrated, verified, or validated. This year-end progress report documents the FY10 status of acquisition, development, and integration of thermal-hydrologic-chemical-mechanical (THCM) code capabilities, frameworks, and enabling tools and infrastructure.

  4. Development and Validation of A Nuclear Fuel Cycle Analysis Tool: A FUTURE Code

    Energy Technology Data Exchange (ETDEWEB)

    Kim, S. K.; Ko, W. I. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Yoon Hee [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

    2013-10-15

    This paper presents the development and validation methods of the FUTURE (FUel cycle analysis Tool for nUcleaR Energy) code, which was developed for a dynamic material flow evaluation and economic analysis of the nuclear fuel cycle. This code enables an evaluation of a nuclear material flow and its economy for diverse nuclear fuel cycles based on a predictable scenario. The most notable virtue of this FUTURE code, which was developed using C and MICROSOFT SQL DBMS, is that a program user can design a nuclear fuel cycle process easily using a standard process on the canvas screen through a drag-and-drop method. From the user's point of view, this code is very easy to use thanks to its high flexibility. In addition, the new code also enables the maintenance of data integrity by constructing a database environment of the results of the nuclear fuel cycle analyses.

  5. DEVELOPMENT AND VALIDATION OF A NUCLEAR FUEL CYCLE ANALYSIS TOOL: A FUTURE CODE

    Directory of Open Access Journals (Sweden)

    S.K. KIM

    2013-10-01

    Full Text Available This paper presents the development and validation methods of the FUTURE (FUel cycle analysis Tool for nUcleaR Energy code, which was developed for a dynamic material flow evaluation and economic analysis of the nuclear fuel cycle. This code enables an evaluation of a nuclear material flow and its economy for diverse nuclear fuel cycles based on a predictable scenario. The most notable virtue of this FUTURE code, which was developed using C# and MICROSOFT SQL DBMS, is that a program user can design a nuclear fuel cycle process easily using a standard process on the canvas screen through a drag-and-drop method. From the user's point of view, this code is very easy to use thanks to its high flexibility. In addition, the new code also enables the maintenance of data integrity by constructing a database environment of the results of the nuclear fuel cycle analyses.

  6. Implementation of QR Code and Digital Signature to Determine the Validity of KRS and KHS Documents

    Directory of Open Access Journals (Sweden)

    Fatich Fazlur Rochman

    2017-05-01

    Full Text Available Universitas Airlangga students often find it difficult to verify the mark that came out in the Kartu Hasil Studi (KHS is called Study Result Card or courses taken in the Kartu Rencana Studi (KRS is called Study Plan Card, if there are changes to the data on the system used Universitas Airlangga. This complicated KRS and KHS verification process happened because the KRS and KHS documents that owned by student is easier to counterfeit than the data in the system. Implementation digital signature and QR Code technology as a solution that can prove the validity of KRS or KHS. The KRS and KHS validation system developed by Digital Signature and QR Code. QR Code is a type of matrix code that was developed as a code that allows its contents to be decoded at high speed while the Digital Signature has a function as a marker on the data to ensure that the data is the original data. The verification process was divided into two types are reading the Digital Signature and printing document that works by scanning the data from QR Code. The application of the system is carried out were the addition of the QR Code on KRS and KHS, required a readiness of human resources. 

  7. Finite mixture models for sensitivity analysis of thermal hydraulic codes for passive safety systems analysis

    Energy Technology Data Exchange (ETDEWEB)

    Di Maio, Francesco, E-mail: francesco.dimaio@polimi.it [Energy Department, Politecnico di Milano, Via La Masa 34, 20156 Milano (Italy); Nicola, Giancarlo [Energy Department, Politecnico di Milano, Via La Masa 34, 20156 Milano (Italy); Zio, Enrico [Energy Department, Politecnico di Milano, Via La Masa 34, 20156 Milano (Italy); Chair on System Science and Energetic Challenge Fondation EDF, Ecole Centrale Paris and Supelec, Paris (France); Yu, Yu [School of Nuclear Science and Engineering, North China Electric Power University, 102206 Beijing (China)

    2015-08-15

    Highlights: • Uncertainties of TH codes affect the system failure probability quantification. • We present Finite Mixture Models (FMMs) for sensitivity analysis of TH codes. • FMMs approximate the pdf of the output of a TH code with a limited number of simulations. • The approach is tested on a Passive Containment Cooling System of an AP1000 reactor. • The novel approach overcomes the results of a standard variance decomposition method. - Abstract: For safety analysis of Nuclear Power Plants (NPPs), Best Estimate (BE) Thermal Hydraulic (TH) codes are used to predict system response in normal and accidental conditions. The assessment of the uncertainties of TH codes is a critical issue for system failure probability quantification. In this paper, we consider passive safety systems of advanced NPPs and present a novel approach of Sensitivity Analysis (SA). The approach is based on Finite Mixture Models (FMMs) to approximate the probability density function (i.e., the uncertainty) of the output of the passive safety system TH code with a limited number of simulations. We propose a novel Sensitivity Analysis (SA) method for keeping the computational cost low: an Expectation Maximization (EM) algorithm is used to calculate the saliency of the TH code input variables for identifying those that most affect the system functional failure. The novel approach is compared with a standard variance decomposition method on a case study considering a Passive Containment Cooling System (PCCS) of an Advanced Pressurized reactor AP1000.

  8. Contributions to the validation of advanced codes for accident analysis calculations with 3-dimensional neutron kinetics. STC with the Ukraine. Final report

    International Nuclear Information System (INIS)

    Grundmann, U.; Kliem, S.; Rohde, U.; Khalimonchuk, V.; Kuchin, A.; Seidel, A.

    2000-10-01

    In the frame of a project of scientific-technical cooperation funded by BMBF/BMWi, the coupled code ATHLET-DYN3D has been transferred to the Scientific and Technical Centre on Nuclear and Radiation Safety Kiev (Ukraine). This program code represents an implementation of the 3D core model DYN3D developed by FZR into the GRS thermohydraulics code system ATHLET. For the purpose of validation of this coupled code, a measurement data base has been generated. In the data base suitable experimental data for operational transients from NPPs are collected. The data collection and documentation was performed in accordance with a directive about requirements to measurement data for code validation, which has been elaborated within the project. The validation calculations have been performed for two selected transients. The results of these calculations were compared with measurement values from the data base. The function of the code DYN3D was expanded with a subroutine for reactivity coefficients calculation. Using this modification of the code DYN3D, investigations of reactivity contributions on different operational processes can be performed. (orig.) [de

  9. Extension of CFD Codes Application to Two-Phase Flow Safety Problems - Phase 3

    International Nuclear Information System (INIS)

    Bestion, D.; Anglart, H.; Mahaffy, J.; Lucas, D.; Song, C.H.; Scheuerer, M.; Zigh, G.; Andreani, M.; Kasahara, F.; Heitsch, M.; Komen, E.; Moretti, F.; Morii, T.; Muehlbauer, P.; Smith, B.L.; Watanabe, T.

    2014-11-01

    The Writing Group 3 on the extension of CFD to two-phase flow safety problems was formed following recommendations made at the 'Exploratory Meeting of Experts to Define an Action Plan on the Application of Computational Fluid Dynamics (CFD) Codes to Nuclear Reactor Safety Problems' held in Aix-en-Provence, in May 2002. Extension of CFD codes to two-phase flow is significant potentiality for the improvement of safety investigations, by giving some access to smaller scale flow processes which were not explicitly described by present tools. Using such tools as part of a safety demonstration may bring a better understanding of physical situations, more confidence in the results, and an estimation of safety margins. The increasing computer performance allows a more extensive use of 3D modelling of two-phase Thermal hydraulics with finer nodalization. However, models are not as mature as in single phase flow and a lot of work has still to be done on the physical modelling and numerical schemes in such two-phase CFD tools. The Writing Group listed and classified the NRS problems where extension of CFD to two-phase flow may bring real benefit, and classified different modelling approaches in a first report (Bestion et al., 2006). First ideas were reported about the specification and analysis of needs in terms of validation and verification. It was then suggested to focus further activity on a limited number of NRS issues with a high priority and a reasonable chance to be successful in a reasonable period of time. The WG3-step 2 was decided with the following objectives: - selection of a limited number of NRS issues having a high priority and for which two-phase CFD has a reasonable chance to be successful in a reasonable period of time; - identification of the remaining gaps in the existing approaches using two-phase CFD for each selected NRS issue; - review of the existing data base for validation of two-phase CFD application to the selected NRS problems

  10. Performance Evaluation of SMART Passive Safety System for Small Break LOCA Using MARS Code

    International Nuclear Information System (INIS)

    Chun, Ji Han; Lee, Guy Hyung; Bae, Kyoo Hwan; Chung, Young Jong; Kim, Keung Koo

    2013-01-01

    SMART has significantly enhanced safety by reducing its core damage frequency to 1/10 that of a conventional nuclear power plant. KAERI is developing a passive safety injection system to replace the active safety injection pump in SMART. It consists of four trains, each of which includes gravity-driven core makeup tank (CMT) and safety injection tank (SIT). This system is required to meet the passive safety performance requirements, i.e., the capability to maintain a safe shutdown condition for a minimum of 72 hours without an AC power supply or operator action in the case of design basis accidents (DBAs). The CMT isolation valve is opened by the low pressurizer pressure signal, and the SIT isolation valve is opened at 2 MPa. Additionally, two stages of automatic depressurization systems are used for rapid depressurization. Preliminary safety analysis of SMART passive safety system in the event of a small-break loss-of-coolant accident (SBLOCA) was performed using MARS code. In this study, the safety analysis results of a guillotine break of safety injection line which was identified as the limiting SBLOCA in SMART are given. The preliminary safety analysis of a SBLOCA for the SMART passive safety system was performed using the MARS code. The analysis results of the most limiting SI line guillotine break showed that the collapsed liquid level inside the core support barrel was maintained sufficiently high above the top of core throughout the transient. This means that the passive safety injection flow from the CMT and SIT causes no core uncovery during the 72 hours following the break with no AC power supply or operator action, which in turn results in a consistent decrease in the fuel cladding temperature. Therefore, the SMART passive safety system can meet the passive safety performance requirement of maintaining the plant at a safe shutdown condition for a minimum of 72 hours without AC power or operator action for a representing accident of SBLOCA

  11. Development and application of best-estimate LWR safety analysis codes

    International Nuclear Information System (INIS)

    Reocreux, M.

    1997-01-01

    This paper is a review of the status and the future orientations of the development and application of best estimate LWR safety analysis codes. The present status of these codes exhibits a large success and almost a complete fulfillment of the objectives which were assigned in the 70s. The applications of Best Estimate codes are numerous and cover a large variety of safety questions. However these applications raised a number of problems. The first ones concern the need to have a better control of the quality of the results. This means requirements on code assessment and on uncertainties evaluation. The second ones concern needs for code development and specifically regarding physical models, numerics, coupling with other codes and programming. The analysis of the orientations for code developments and applications in the next years, shows that some developments should be made without delay in order to solve today questions whereas some others are more long term and should be tested for example in some pilot programmes before being eventually applied in main code development. Each of these development programmes are analyzed in the paper by detailing their main content and their possible interest. (author)

  12. International assessment of application of the Code of Conduct on the Safety of Research Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Shokr, A.M. [Atomic Energy Authority, Abouzabal (Egypt). Egypt Second Research Reactor

    2015-11-15

    The self-assessments performed by thirty-eight countries on application of the Code of Conduct on the Safety of Research Reactors were analyzed and discussed. The results of this analysis were used to identify areas of satisfactory application of the Code and area needing improvements, and therefore require more attention worldwide. The results showed improvement in application of the Code provisions; notably in aging management, regulatory supervision, and consideration of human factors. However, there is a continuing need for further improvement in these areas, as well as in operational radiation protection, emergency preparedness and decommissioning planning. Additionally, increased attention needs to be given to periodic safety reviews, evaluation of site-specific hazards, and assessment of extreme external events. The results showed consistency with the feedback from other sources of information on generic safety issues for research reactors.

  13. International assessment of application of the Code of Conduct on the Safety of Research Reactors

    International Nuclear Information System (INIS)

    Shokr, A.M.

    2015-01-01

    The self-assessments performed by thirty-eight countries on application of the Code of Conduct on the Safety of Research Reactors were analyzed and discussed. The results of this analysis were used to identify areas of satisfactory application of the Code and area needing improvements, and therefore require more attention worldwide. The results showed improvement in application of the Code provisions; notably in aging management, regulatory supervision, and consideration of human factors. However, there is a continuing need for further improvement in these areas, as well as in operational radiation protection, emergency preparedness and decommissioning planning. Additionally, increased attention needs to be given to periodic safety reviews, evaluation of site-specific hazards, and assessment of extreme external events. The results showed consistency with the feedback from other sources of information on generic safety issues for research reactors.

  14. Code of Sustainable Practice in Occupational and Environmental Health and Safety for Corporations.

    Science.gov (United States)

    Castleman, Barry; Allen, Barbara; Barca, Stefania; Bohme, Susanna Rankin; Henry, Emmanuel; Kaur, Amarjit; Massard-Guilbaud, Genvieve; Melling, Joseph; Menendez-Navarro, Alfredo; Renfrew, Daniel; Santiago, Myrna; Sellers, Christopher; Tweedale, Geoffrey; Zalik, Anna; Zavestoski, Stephen

    2008-01-01

    At a conference held at Stony Brook University in December 2007, "Dangerous Trade: Histories of Industrial Hazard across a Globalizing World," participants endorsed a Code of Sustainable Practice in Occupational and Environmental Health and Safety for Corporations. The Code outlines practices that would ensure corporations enact the highest health and environmentally protective measures in all the locations in which they operate. Corporations should observe international guidelines on occupational exposure to air contaminants, plant safety, air and water pollutant releases, hazardous waste disposal practices, remediation of polluted sites, public disclosure of toxic releases, product hazard labeling, sale of products for specific uses, storage and transport of toxic intermediates and products, corporate safety and health auditing, and corporate environmental auditing. Protective measures in all locations should be consonant with the most protective measures applied anywhere in the world, and should apply to the corporations' subsidiaries, contractors, suppliers, distributors, and licensees of technology. Key words: corporations, sustainability, environmental protection, occupational health, code of practice.

  15. Safety, codes and standards for hydrogen installations. Metrics development and benchmarking

    Energy Technology Data Exchange (ETDEWEB)

    Harris, Aaron P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dedrick, Daniel E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); LaFleur, Angela Christine [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); San Marchi, Christopher W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-04-01

    Automakers and fuel providers have made public commitments to commercialize light duty fuel cell electric vehicles and fueling infrastructure in select US regions beginning in 2014. The development, implementation, and advancement of meaningful codes and standards is critical to enable the effective deployment of clean and efficient fuel cell and hydrogen solutions in the energy technology marketplace. Metrics pertaining to the development and implementation of safety knowledge, codes, and standards are important to communicate progress and inform future R&D investments. This document describes the development and benchmarking of metrics specific to the development of hydrogen specific codes relevant for hydrogen refueling stations. These metrics will be most useful as the hydrogen fuel market transitions from pre-commercial to early-commercial phases. The target regions in California will serve as benchmarking case studies to quantify the success of past investments in research and development supporting safety codes and standards R&D.

  16. Development Perspective of Regulatory Audit Code System for SFR Nuclear Safety Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Bae, Moo Hoon; Lee, Gil Soo; Shin, An Dong; Suh, Nam Duk [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2012-05-15

    A sodium-cooled fast reactor (SFR) in Korea is based on the KALIMER-600 concept developed by KAERI. Based on 'Long-term R and D Plan for Future Reactor Systems' which was approved by the Korea Atomic Energy Commission in 2008, the KAERI designer is scheduled to apply the design certification of the prototype SFR in 2017. In order to establish regulatory infrastructure for the licensing of a prototype SFR, KINS has develop the regulatory requirements for the demonstration SFR since 2010, and are scheduled to develop the regulatory audit code systems in regard to core, fuel, and system, etc. since 2012. In this study, the domestic code systems used for core design and safety evaluation of PWRs and the nuclear physics and code system for SFRs were briefly reviewed, and the development perspective of regulatory audit code system for SFR nuclear safety evaluation were derived

  17. Validation of the computer code system ATHLET / ATHLET-CD. Final report; Validierung des Rechenprogrammsystems ATHLET / ATHLET-CD. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Austregesilo, H.; Bals, C.; Erdmann, W.; Horche, W.; Krzykacz-Hausmann, B.; Pointner, W.; Schoeffel, P.; Skorek, T.; Weber, S.; Wielenberg, A.

    2010-04-15

    In the frame of the reactor safety project RS1173, sponsored by the German Federal Ministry of Economics and Technology, analyses of international integral and separate effects tests have been performed for the validation of the code system ATHLET/ATHLET-CD. The work mainly comprised post-test calculations of selected experiments and the contributions to the working groups accompanying the experimental programs. For the assessment of the thermal-hydraulic models in ATHLET 8 integral tests and 4 separate effect tests have been considered. Together with the corroboration of the existing models, the validation analyses were mainly dedicated to the assessment of the modelling of non-condensable gases and their influence on two-phase natural circulation and on the primary heat removal through steam generators, as well as of the simulation of multi-dimensional flow processes. The validation calculations with respect to the simulation of multi-dimensional one- and two-phase flows aimed to investigate the range of applicability and limitations of the method of parallel channels in connection with the separate momentum equations for water and steam current used in ATHLET as well as to assess the status of the coupled version ATHLET/FLUBOX-3D. The ATHLET-CD validation analyses included the post-test calculations of 9 bundle tests, and was mainly focussed on the assessment of the improved and new models for core degradation, including the models for oxidation, melt formation and relocation for BWR components, as well as of the modelling of fission products and aerosol transport within the primary circuit taking into account chemical reactions within the module SOPHAEROS. As an additional contribution to code validation, the GRS methodology of uncertainty and sensitivity analysis was applied exemplarily to two validation calculations, one with ATHLET and one with ATHLET-CD. The results of these uncertainty analyses endorse the capability of the code system to reproduce

  18. Development and validation of computer codes for analysis of PHWR containment behaviour

    International Nuclear Information System (INIS)

    Markandeya, S.G.; Haware, S.K.; Ghosh, A.K.; Venkat Raj, V.

    1997-01-01

    In order to ensure that the design intent of the containment of Indian Pressurised Heavy Water Reactors (IPHWRs) is met, both analytical and experimental studies are being pursued at BARC. As a part of analytical studies, computer codes for predicting the behaviour of containment under various accident scenarios are developed/adapted. These include codes for predicting 1) pressure, temperature transients in the containment following either Loss of Coolant Accident (LOCA) or Main Steam Line Break (MSLB), 2) hydrogen behaviour in respect of its distribution, combustion and the performance of proposed mitigation systems, and 3) behaviour of fission product aerosols in the piping circuits of the primary heat transport system and in the containment. All these codes have undergone thorough validation using data obtained from in-house test facilities or from international sources. Participation in the International Standard Problem (ISP) exercises has also helped in validation of the codes. The present paper briefly describes some of these codes and the various exercises performed for their validation. (author)

  19. Preliminary validation of the MATRA-LMR-FB code for the flow blockage in a subassembly

    International Nuclear Information System (INIS)

    Jeong, H. Y.; Ha, K. S.; Kwon, Y. M.; Chang, W. P.; Lee, Y. B.; Heo, S.

    2005-01-01

    To analyze the flow blockage in a subassembly of a Liquid Metal-cooled Reactor (LMR), the MATRA-LMR-FB code has been developed and validated for the existing experimental data. Compared to the MATRA-LMR code, which had been successfully applied for the core thermal-hydraulic design of KALIMER, the MATRA-LMR-FB code includes some advanced modeling features. Firstly, the Distributed Resistance Model (DRM), which enables a very accurate description of the effects of wire-wrap and blockage in a flow path, is developed for the MATRA-LMR-FB code. Secondly, the hybrid difference method is used to minimize the numerical diffusion especially at the low flow region such as recirculating wakes after blockage. In addition, the code is equipped with various turbulent mixing models to describe the active mixing due to the turbulent motions as accurate as possible. For the validation of the MATRA-LMR-FB code the ORNL THORS test and KOS 169-pin test are analyzed. Based on the analysis results for the temperature data, the accuracy of the code is evaluated quantitatively. The MATRA-LMR-FB code predicts very accurately the exit temperatures measured in the subassembly with wire-wrap. However, the predicted temperatures for the experiment with spacer grid show some deviations from the measured. To enhance the accuracy of the MATRA-LMR-FB for the flow path with grid spacers, it is suggested to improve the models for pressure loss due to spacer grid and the modeling method for blockage itself. The developed MATRA-LMR-FB code is evaluated to be applied to the flow blockage analysis of KALIMER-600 which adopts the wire-wrapped subassemblies

  20. Development and validation of three-dimensional CFD techniques for reactor safety applications. Final report

    International Nuclear Information System (INIS)

    Buchholz, Sebastian; Palazzo, Simone; Papukchiev, Angel; Scheurer Martina

    2016-12-01

    The overall goal of the project RS 1506 ''Development and Validation of Three Dimensional CFD Methods for Reactor Safety Applications'' is the validation of Computational Fluid Dynamics (CFD) software for the simulation of three -dimensional thermo-hydraulic heat and fluid flow phenomena in nuclear reactors. For this purpose a wide spectrum of validation and test cases was selected covering fluid flow and heat transfer phenomena in the downcomer and in the core of pressurized water reactors. In addition, the coupling of the system code ATHLET with the CFD code ANSYS CFX was further developed and validated. The first choice were UPTF experiments where turbulent single- and two-phase flows were investigated in a 1:1 scaled model of a German KONVOI reactor. The scope of the CFD calculations covers thermal mixing and stratification including condensation in single- and two-phase flows. In the complex core region, the flow in a fuel assembly with spacer grid was simulated as defined in the OECD/NEA Benchmark MATIS-H. Good agreement are achieved when the geometrical and physical boundary conditions were reproduced as realistic as possible. This includes, in particular, the consideration of heat transfer to walls. The influence of wall modelling on CFD results was investigated on the TALL-3D T01 experiment. In this case, the dynamic three dimensional fluid flow and heat transfer phenomena were simulated in a Generation IV liquid metal cooled reactor. Concurrently to the validation work, the coupling of the system code ATHLET with the ANSYS CFX software was optimized and expanded for two-phase flows. Different coupling approaches were investigated, in order to overcome the large difference between CPU-time requirements of system and CFD codes. Finally, the coupled simulation system was validated by applying it to the simulation of the PSI double T-junction experiment, the LBE-flow in the MYRRA Spallation experiment and a demonstration test case simulating a pump trip

  1. Kuosheng BWR/6 containment safety analysis with gothic code

    International Nuclear Information System (INIS)

    Lin Ansheng; Wang Jongrong; Yuann Rueyyng; Shih Chunkuan

    2011-01-01

    Kuosheng Nuclear Power Plant in Taiwan is a GE-designed twin-unit BWR/6 plant, each unit rated at 2894 MWt. In this study, we presented the calculated results of the containment pressure and temperature responses after the main steam line break accident, which is the design basis for the containment system. During the simulation, a power of SPU range (105.1%) was used and a model of the Mark III type containment was built using the containment thermal-hydraulic program GOTHIC. The simulation consists of short and long-term responses. The drywell pressure and temperature responses which display the maximum values in the early state of the LOCA were investigated in the short-term response; the primary containment pressure and temperature responses in the long-term response. The blowdown flow was provided by FSAR and used as boundary conditions in the short-term model; in the long-term model, the blowdown flow was calculated using a GOTHIC built-in homogeneous equilibrium model. In the long-term analysis, a simplifier RPV model was employed to calculate the blowdown flow. Finally, the calculated results, similar to the FSAR results, indicate the GOTHIC code has the capability to simulate the pressure/temperature response of Mark III containment to the main steam line break LOCA. (author)

  2. Validation of a pre-coded food record for infants and young children

    DEFF Research Database (Denmark)

    Gondolf, Ulla Holmboe; Tetens, Inge; Hills, A. P.

    2012-01-01

    Background/Objectives:To assess the validity of a 7-day pre-coded food record (PFR) method in 9-month-old infants against metabolizable energy intake (ME(DLW)) measured by doubly labeled water (DLW); additionally to compare PFR with a 7-day weighed food record (WFR) in 9-month-old infants and 36...

  3. Further validation of liquid metal MHD code for unstructured grid based on OpenFOAM

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Jingchao; Chen, Hongli, E-mail: hlchen1@ustc.edu.cn; He, Qingyun; Ye, Minyou

    2015-11-15

    Highlights: • Specific correction scheme has been adopted to revise the calculating result for non-orthogonal meshes. • The developed MHD code based on OpenFOAM platform has been validated by benchmark cases under uniform and non-uniform magnetic field in round and rectangular ducts. • ALEX experimental results have been used to validate the MHD code based on OpenFOAM. - Abstract: In fusion liquid metal blankets, complex geometries involving contractions, expansions, bends, manifolds are very common. The characteristics of liquid metal flow in these geometries are significant. In order to extend the magnetohydrodynamic (MHD) solver developed on OpenFOAM platform to be applied in the complex geometry, the MHD solver based on unstructured meshes has been implemented. The adoption of non-orthogonal correction techniques in the solver makes it possible to process the non-orthogonal meshes in complex geometries. The present paper focused on the validation of the code under critical conditions. An analytical solution benchmark case and two experimental benchmark cases were conducted to validate the code. Benchmark case I is MHD flow in a circular pipe with arbitrary electric conductivity of the walls in a uniform magnetic field. Benchmark cases II and III are experimental cases of 3D laminar steady MHD flow under fringing magnetic field. In all these cases, the numerical results match well with the benchmark cases.

  4. Further validation of liquid metal MHD code for unstructured grid based on OpenFOAM

    International Nuclear Information System (INIS)

    Feng, Jingchao; Chen, Hongli; He, Qingyun; Ye, Minyou

    2015-01-01

    Highlights: • Specific correction scheme has been adopted to revise the calculating result for non-orthogonal meshes. • The developed MHD code based on OpenFOAM platform has been validated by benchmark cases under uniform and non-uniform magnetic field in round and rectangular ducts. • ALEX experimental results have been used to validate the MHD code based on OpenFOAM. - Abstract: In fusion liquid metal blankets, complex geometries involving contractions, expansions, bends, manifolds are very common. The characteristics of liquid metal flow in these geometries are significant. In order to extend the magnetohydrodynamic (MHD) solver developed on OpenFOAM platform to be applied in the complex geometry, the MHD solver based on unstructured meshes has been implemented. The adoption of non-orthogonal correction techniques in the solver makes it possible to process the non-orthogonal meshes in complex geometries. The present paper focused on the validation of the code under critical conditions. An analytical solution benchmark case and two experimental benchmark cases were conducted to validate the code. Benchmark case I is MHD flow in a circular pipe with arbitrary electric conductivity of the walls in a uniform magnetic field. Benchmark cases II and III are experimental cases of 3D laminar steady MHD flow under fringing magnetic field. In all these cases, the numerical results match well with the benchmark cases.

  5. Code of conduct on the safety and security of radioactive sources

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The objective of this Code is to achieve and maintain a high level of safety and security of radioactive sources through the development, harmonization and enforcement of national policies, laws and regulations, and through tile fostering of international co-operation. In particular, this Code addresses the establishment of an adequate system of regulatory control from the production of radioactive sources to their final disposal, and a system for the restoration of such control if it has been lost.

  6. Code of conduct on the safety and security of radioactive sources

    International Nuclear Information System (INIS)

    2001-03-01

    The objective of this Code is to achieve and maintain a high level of safety and security of radioactive sources through the development, harmonization and enforcement of national policies, laws and regulations, and through tile fostering of international co-operation. In particular, this Code addresses the establishment of an adequate system of regulatory control from the production of radioactive sources to their final disposal, and a system for the restoration of such control if it has been lost

  7. Validation of thermal hydraulic computer codes for advanced light water reactor

    International Nuclear Information System (INIS)

    Macek, J.

    2001-01-01

    The Czech Republic operates 4 WWER-440 units, two WWER-1000 units are being finalised (one of them is undergoing commissioning). Thermal-hydraulics Department of the Nuclear Research Institute Rez performs accident analyses for these plants using a number of computer codes. To model the primary and secondary circuits behaviour the system codes ATHLET, CATHARE, RELAP, TRAC are applied. Containment and pressure-suppressure system are modelled with RALOC and MELCOR codes, the reactor power calculations (point and space-neutron kinetics) are made with DYN3D, NESTLE and CDF codes (FLUENT, TRIO) are used for some specific problems. An integral part of the current Czech project 'New Energy Sources' is selection of a new nuclear source. Within this and the preceding projects financed by the Czech Ministry of Industry and Trade and the EU PHARE, the Department carries and has carried out the systematic validation of thermal-hydraulic and reactor physics computer codes applying data obtained on several experimental facilities as well as the real operational data. The paper provides a concise information on these activities of the NRI and its Thermal-hydraulics Department. A detailed example of the system code validation and the consequent utilisation of the results for a real NPP purposes is included. (author)

  8. Test and validation of the iterative code for the neutrons spectrometry and dosimetry: NSDUAZ

    International Nuclear Information System (INIS)

    Reyes H, A.; Ortiz R, J. M.; Reyes A, A.; Castaneda M, R.; Solis S, L. O.; Vega C, H. R.

    2014-08-01

    In this work was realized the test and validation of an iterative code for neutronic spectrometry known as Neutron Spectrometry and Dosimetry of the Universidad Autonoma de Zacatecas (NSDUAZ). This code was designed in a user graph interface, friendly and intuitive in the environment programming of LabVIEW using the iterative algorithm known as SPUNIT. The main characteristics of the program are: the automatic selection of the initial spectrum starting from the neutrons spectra catalog compiled by the International Atomic Energy Agency, the possibility to generate a report in HTML format that shows in graph and numeric way the neutrons flowing and calculates the ambient dose equivalent with base to this. To prove the designed code, the count rates of a spectrometer system of Bonner spheres were used with a detector of 6 LiI(Eu) with 7 polyethylene spheres with diameter of 0, 2, 3, 5, 8, 10 and 12. The count rates measured with two neutron sources: 252 Cf and 239 PuBe were used to validate the code, the obtained results were compared against those obtained using the BUNKIUT code. We find that the reconstructed spectra present an error that is inside the limit reported in the literature that oscillates around 15%. Therefore, it was concluded that the designed code presents similar results to those techniques used at the present time. (Author)

  9. Research on verification and validation strategy of detonation fluid dynamics code of LAD2D

    Science.gov (United States)

    Wang, R. L.; Liang, X.; Liu, X. Z.

    2017-07-01

    The verification and validation (V&V) is an important approach in the software quality assurance of code in complex engineering application. Reasonable and efficient V&V strategy can achieve twice the result with half the effort. This article introduces the software-Lagrangian adaptive hydrodynamics code in 2D space (LAD2D), which is self-developed software in detonation CFD with plastic-elastic structure. The V&V strategy of this detonation CFD code is presented based on the foundation of V&V methodology for scientific software. The basic framework of the module verification and the function validation is proposed, composing the detonation fluid dynamics model V&V strategy of LAD2D.

  10. Safety standards, legislation and codes of practice for fuel cell manufacture and operation

    Energy Technology Data Exchange (ETDEWEB)

    Wilcox, C.P.

    1999-07-01

    This report examines safety standards, legislation and codes of practice for fuel cell manufacture and operation in the UK, Europe and internationally. Management of health and safety in the UK is discussed, and the characteristics of phosphoric acid (PAFC), proton exchange membrane (PEM), molten carbonate (MCFC), solid oxide (SOFC) fuel cells are described. Fuel cell power plant standards and manufacture in the UK, design and operational considerations, end of life disposal, automotive fuel cell system, and fuelling and vehicular concerns are explored, and standards, legislation and codes of practice are explained in the appendix.

  11. Lightning protection design of nuclear power plants. KTA safety code, version 6/99

    International Nuclear Information System (INIS)

    1999-06-01

    This KTA safety code does not cover calculation methods for determination of lightning-induced voltage inputs to control room systems within the reactor building, as the literature presents a variety of applicable methods, which however cannot be directly applied to any power plant, due to the great diversity of geometries of the electrical systems and control room systems in nuclear power plants. Compliance with the design requirements of this safety code for shielding of buildings, and installation and shielding of cables, can be considered to offer the appropriate protection. (orig./CB) [de

  12. Verification of codes used for the nuclear safety assessment of the small space heterogeneous reactors with zirconium hydride moderator

    International Nuclear Information System (INIS)

    Glushkov, E.S.; Gomin, E.A.; Kompaniets, G.V.

    1994-01-01

    Computer codes used for assessment of nuclear safety for space NPP are compared taking as an example small-sized heterogeneous reactor with zirconium hydride moderator of the Topaz-2 facility. The code verifications are made for five different variants

  13. Reactor physics computer code development for neutronic design, fuel-management, reactor operation and safety analysis of PHWRs

    International Nuclear Information System (INIS)

    Rastogi, B.P.

    1989-01-01

    This report discusses various reactor physics codes developed for neutronic design, fuel-management, reactor operation and safety analysis of PHWRs. These code packages have been utilized for nuclear design of 500 MWe and new 235 MWe PHWRs. (author)

  14. Independent verification and validation testing of the FLASH computer code, Versiion 3.0

    International Nuclear Information System (INIS)

    Martian, P.; Chung, J.N.

    1992-06-01

    Independent testing of the FLASH computer code, Version 3.0, was conducted to determine if the code is ready for use in hydrological and environmental studies at various Department of Energy sites. This report describes the technical basis, approach, and results of this testing. Verification tests, and validation tests, were used to determine the operational status of the FLASH computer code. These tests were specifically designed to test: correctness of the FORTRAN coding, computational accuracy, and suitability to simulating actual hydrologic conditions. This testing was performed using a structured evaluation protocol which consisted of: blind testing, independent applications, and graduated difficulty of test cases. Both quantitative and qualitative testing was performed through evaluating relative root mean square values and graphical comparisons of the numerical, analytical, and experimental data. Four verification test were used to check the computational accuracy and correctness of the FORTRAN coding, and three validation tests were used to check the suitability to simulating actual conditions. These tests cases ranged in complexity from simple 1-D saturated flow to 2-D variably saturated problems. The verification tests showed excellent quantitative agreement between the FLASH results and analytical solutions. The validation tests showed good qualitative agreement with the experimental data. Based on the results of this testing, it was concluded that the FLASH code is a versatile and powerful two-dimensional analysis tool for fluid flow. In conclusion, all aspects of the code that were tested, except for the unit gradient bottom boundary condition, were found to be fully operational and ready for use in hydrological and environmental studies

  15. Development of safety evaluation methods and analysis codes applied to the safety regulations for the design and construction stage of fast breeder reactor

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-15

    The purposes of this study are to develop the safety evaluation methods and analysis codes needed in the design and construction stage of fast breeder reactor (FBR). In JFY 2012, the following results are obtained. As for the development of safety evaluation methods needed in the safety examination conducted for the reactor establishment permission, development of the analysis codes, such as core damage analysis code, were carried out following the planned schedule. As for the development of the safety evaluation method needed for the risk informed safety regulation, the quantification technique of the event tree using the Continuous Markov chain Monte Carlo method (CMMC method) were studied. (author)

  16. Code of practice on quality assurance for safety in nuclear power plants

    International Nuclear Information System (INIS)

    1988-01-01

    The code sets forth the management principles and objectives to be met during the implementation of activities in different phases of the nuclear power plants (NPPs) for assuring safety. It is intended for use by organisations and individuals responsible for safety related functions in design, manufacturing, construction, commissioning, operation and decommissioning of NPPs. It covers the functions of management, performance, verification and corrective action. It also deals with the quality assurance records. (M.G.B.)

  17. Initial verification and validation of RAZORBACK - A research reactor transient analysis code

    Energy Technology Data Exchange (ETDEWEB)

    Talley, Darren G. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2015-09-01

    This report describes the work and results of the initial verification and validation (V&V) of the beta release of the Razorback code. Razorback is a computer code designed to simulate the operation of a research reactor (such as the Annular Core Research Reactor (ACRR)) by a coupled numerical solution of the point reactor kinetics equations, the energy conservation equation for fuel element heat transfer, and the mass, momentum, and energy conservation equations for the water cooling of the fuel elements. This initial V&V effort was intended to confirm that the code work to-date shows good agreement between simulation and actual ACRR operations, indicating that the subsequent V&V effort for the official release of the code will be successful.

  18. Uncertainty propagation applied to multi-scale thermal-hydraulics coupled codes. A step towards validation

    Energy Technology Data Exchange (ETDEWEB)

    Geffray, Clotaire Clement

    2017-03-20

    The work presented here constitutes an important step towards the validation of the use of coupled system thermal-hydraulics and computational fluid dynamics codes for the simulation of complex flows in liquid metal cooled pool-type facilities. First, a set of methods suited for uncertainty and sensitivity analysis and validation activities with regards to the specific constraints of the work with coupled and expensive-to-run codes is proposed. Then, these methods are applied to the ATHLET - ANSYS CFX model of the TALL-3D facility. Several transients performed at this latter facility are investigated. The results are presented, discussed and compared to the experimental data. Finally, assessments of the validity of the selected methods and of the quality of the model are offered.

  19. Report on nuclear industry quality assurance procedures for safety analysis computer code development and use

    International Nuclear Information System (INIS)

    Sheron, B.W.; Rosztoczy, Z.R.

    1980-08-01

    As a result of a request from Commissioner V. Gilinsky to investigate in detail the causes of an error discovered in a vendor Emergency Core Cooling System (ECCS) computer code in March, 1978, the staff undertook an extensive investigation of the vendor quality assurance practices applied to safety analysis computer code development and use. This investigation included inspections of code development and use practices of the four major Light Water Reactor Nuclear Steam Supply System vendors and a major reload fuel supplier. The conclusion reached by the staff as a result of the investigation is that vendor practices for code development and use are basically sound. A number of areas were identified, however, where improvements to existing vendor procedures should be made. In addition, the investigation also addressed the quality assurance (QA) review and inspection process for computer codes and identified areas for improvement

  20. Validation of ICD-9 Codes for Stable Miscarriage in the Emergency Department.

    Science.gov (United States)

    Quinley, Kelly E; Falck, Ailsa; Kallan, Michael J; Datner, Elizabeth M; Carr, Brendan G; Schreiber, Courtney A

    2015-07-01

    International Classification of Disease, Ninth Revision (ICD-9) diagnosis codes have not been validated for identifying cases of missed abortion where a pregnancy is no longer viable but the cervical os remains closed. Our goal was to assess whether ICD-9 code "632" for missed abortion has high sensitivity and positive predictive value (PPV) in identifying patients in the emergency department (ED) with cases of stable early pregnancy failure (EPF). We studied females ages 13-50 years presenting to the ED of an urban academic medical center. We approached our analysis from two perspectives, evaluating both the sensitivity and PPV of ICD-9 code "632" in identifying patients with stable EPF. All patients with chief complaints "pregnant and bleeding" or "pregnant and cramping" over a 12-month period were identified. We randomly reviewed two months of patient visits and calculated the sensitivity of ICD-9 code "632" for true cases of stable miscarriage. To establish the PPV of ICD-9 code "632" for capturing missed abortions, we identified patients whose visits from the same time period were assigned ICD-9 code "632," and identified those with actual cases of stable EPF. We reviewed 310 patient records (17.6% of 1,762 sampled). Thirteen of 31 patient records assigned ICD-9 code for missed abortion correctly identified cases of stable EPF (sensitivity=41.9%), and 140 of the 142 patients without EPF were not assigned the ICD-9 code "632"(specificity=98.6%). Of the 52 eligible patients identified by ICD-9 code "632," 39 cases met the criteria for stable EPF (PPV=75.0%). ICD-9 code "632" has low sensitivity for identifying stable EPF, but its high specificity and moderately high PPV are valuable for studying cases of stable EPF in epidemiologic studies using administrative data.

  1. Application of verification and validation on safety parameter display systems

    International Nuclear Information System (INIS)

    Thomas, N.C.

    1983-01-01

    Offers some explanation of how verification and validation (VandV) can support development and licensing of the Safety Parameter Display Systems (SPDS). Advocates that VandV can be more readily accepted within the nuclear industry if a better understanding exists of what the objectives of VandV are and should be. Includes a discussion regarding a reasonable balance of costs and benefits of VandV as applied to the SPDS and to other digital systems. Represents the author's perception of the regulator's perspective based on background information and experience, and discussions with regulators about their current concerns and objectives. Suggests that the introduction of the SPDS into the Control Room is a first step towards growing dependency on use of computers

  2. Recent development and application of a new safety analysis code for fusion reactors

    Energy Technology Data Exchange (ETDEWEB)

    Merrill, Brad J., E-mail: Brad.Merrill@inl.gov; Humrickhouse, Paul W.; Shimada, Masashi

    2016-11-01

    Highlights: • This paper presents recent code development activities for the MELCOR for fusion and Tritium Migration Analysis Program computer codes at the Idaho National Engineering Laboratory. • The capabilities of these computer codes are being merged into a single safety analysis tool for fusion reactor accidents. • The result of benchmarking these codes against previous code versions is presented by the authors of this paper. • This new capability is applied to study the tritium inventory and permeation rate for a water cold tungsten divertor that has neutron damage at 0.3 dpa. - Abstract: This paper describes the recent progress made in the development of two codes for fusion reactor safety assessments at the Idaho National Laboratory (INL): MELCOR for fusion and the Tritium Migration Analysis Program (TMAP). During the ITER engineering design activity (EDA), the INL Fusion Safety Program (FSP) modified the MELCOR 1.8.2 code for fusion applications to perform ITER thermal hydraulic safety analyses. Because MELCOR has undergone many improvements at SNL-NM since version 1.8.2 was released, the INL FSP recently imported these same fusion modifications into the MELCOR 1.8.6 code, along with the multiple fluids modifications of MELCOR 1.8.5 for fusion used in US advanced fusion reactor design studies. TMAP has also been under development for several decades at the INL by the FSP. TMAP treats multi-specie surface absorption and diffusion in composite materials with dislocation traps, plus the movement of these species from room to room by fluid flow within a given facility. Recently, TMAP was updated to consider multiple trap site types to allow the simulation of experimental data from neutron irradiated tungsten. The natural development path for both of these codes is to merge their capabilities into one computer code to provide a more comprehensive safety tool for analyzing accidents in fusion reactors. In this paper we detail recent developments in this

  3. Recent development and application of a new safety analysis code for fusion reactors

    International Nuclear Information System (INIS)

    Merrill, Brad J.; Humrickhouse, Paul W.; Shimada, Masashi

    2016-01-01

    Highlights: • This paper presents recent code development activities for the MELCOR for fusion and Tritium Migration Analysis Program computer codes at the Idaho National Engineering Laboratory. • The capabilities of these computer codes are being merged into a single safety analysis tool for fusion reactor accidents. • The result of benchmarking these codes against previous code versions is presented by the authors of this paper. • This new capability is applied to study the tritium inventory and permeation rate for a water cold tungsten divertor that has neutron damage at 0.3 dpa. - Abstract: This paper describes the recent progress made in the development of two codes for fusion reactor safety assessments at the Idaho National Laboratory (INL): MELCOR for fusion and the Tritium Migration Analysis Program (TMAP). During the ITER engineering design activity (EDA), the INL Fusion Safety Program (FSP) modified the MELCOR 1.8.2 code for fusion applications to perform ITER thermal hydraulic safety analyses. Because MELCOR has undergone many improvements at SNL-NM since version 1.8.2 was released, the INL FSP recently imported these same fusion modifications into the MELCOR 1.8.6 code, along with the multiple fluids modifications of MELCOR 1.8.5 for fusion used in US advanced fusion reactor design studies. TMAP has also been under development for several decades at the INL by the FSP. TMAP treats multi-specie surface absorption and diffusion in composite materials with dislocation traps, plus the movement of these species from room to room by fluid flow within a given facility. Recently, TMAP was updated to consider multiple trap site types to allow the simulation of experimental data from neutron irradiated tungsten. The natural development path for both of these codes is to merge their capabilities into one computer code to provide a more comprehensive safety tool for analyzing accidents in fusion reactors. In this paper we detail recent developments in this

  4. Integral large scale experiments on hydrogen combustion for severe accident code validation-HYCOM

    International Nuclear Information System (INIS)

    Breitung, W.; Dorofeev, S.; Kotchourko, A.; Redlinger, R.; Scholtyssek, W.; Bentaib, A.; L'Heriteau, J.-P.; Pailhories, P.; Eyink, J.; Movahed, M.; Petzold, K.-G.; Heitsch, M.; Alekseev, V.; Denkevits, A.; Kuznetsov, M.; Efimenko, A.; Okun, M.V.; Huld, T.; Baraldi, D.

    2005-01-01

    A joint research project was carried out in the EU Fifth Framework Programme, concerning hydrogen risk in a nuclear power plant. The goals were: Firstly, to create a new data base of results on hydrogen combustion experiments in the slow to turbulent combustion regimes. Secondly, to validate the partners CFD and lumped parameter codes on the experimental data, and to evaluate suitable parameter sets for application calculations. Thirdly, to conduct a benchmark exercise by applying the codes to the full scale analysis of a postulated hydrogen combustion scenario in a light water reactor containment after a core melt accident. The paper describes the work programme of the project and the partners activities. Significant progress has been made in the experimental area, where test series in medium and large scale facilities have been carried out with the focus on specific effects of scale, multi-compartent geometry, heat losses and venting. The data were used for the validation of the partners CFD and lumped parameter codes, which included blind predictive calculations and pre- and post-test intercomparison exercises. Finally, a benchmark exercise was conducted by applying the codes to the full scale analysis of a hydrogen combustion scenario. The comparison and assessment of the results of the validation phase and of the challenging containment calculation exercise allows a deep insight in the quality, capabilities and limits of the CFD and the lumped parameter tools which are currently in use at various research laboratories

  5. Validation of a Subchannel Analysis Code MATRA Version 1.0

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Dae Hyun; Seo, Kyung Won; Kwon, Hyouk

    2008-10-15

    A subchannel analysis code MATRA has been developed for the thermal hydraulic analysis of SMART core. The governing equations and important models were established, and validation calculations have been performed for subchannel flow and enthalpy distributions in rod bundles under steady-state conditions. The governing equations of the MATRA were on the basis of integral balance equation of the two-phase mixture. The effects of non-homogeneous and non-equilibrium states were considered by employing the subcooled boiling model and the phasic slip model. Solution scheme and main structure of the MATRA code, as well as the difference of MATRA and COBRA-IV-I codes, were summarized. Eight different test data sets were employed for the validation of the MATRA code. The collected data consisted of single-phase subchannel flow and temperature distribution data, single-phase inlet flow maldistribution data, single-phase partial flow blockage data, and two-phase subchannel flow and enthalpy distribution data. The prediction accuracy as well as the limitation of the MATRA code was evaluated from this analysis.

  6. CSNI Integral Test Facility Matrices for Validation of Best-Estimate Thermal-Hydraulic Computer Codes

    International Nuclear Information System (INIS)

    Glaeser, H.

    2008-01-01

    Internationally agreed Integral Test Facility (ITF) matrices for validation of realistic thermal hydraulic system computer codes were established. ITF development is mainly for Pressurised Water Reactors (PWRs) and Boiling Water Reactors (BWRs). A separate activity was for Russian Pressurised Water-cooled and Water-moderated Energy Reactors (WWER). Firstly, the main physical phenomena that occur during considered accidents are identified, test types are specified, and test facilities suitable for reproducing these aspects are selected. Secondly, a list of selected experiments carried out in these facilities has been set down. The criteria to achieve the objectives are outlined. In this paper some specific examples from the ITF matrices will also be provided. The matrices will be a guide for code validation, will be a basis for comparisons of code predictions performed with different system codes, and will contribute to the quantification of the uncertainty range of code model predictions. In addition to this objective, the construction of such a matrix is an attempt to record information which has been generated around the world over the last years, so that it is more accessible to present and future workers in that field than would otherwise be the case.

  7. IAEA activities to prepare safety codes and guides for thermal neutron nuclear power plants

    International Nuclear Information System (INIS)

    Iansiti, E.

    1977-01-01

    In accordance with the programme presented to, and endorsed by, the eighteenth General Conference in September 1974, the IAEA is now developing a complete set of safety codes and guides that will represent recommendations for the safety of thermal neutron power plants. The safety codes outline the minimum requirements for achieving this safety, and the safety guides set forth the criteria, procedures and methods to implement the safety codes. The whole programme is directed towards the five areas of Governmental Organization, Siting, Design, Operation, and Quality Assurance. One Scientific Secretary from the Agency Secretariat is responsible for each of these areas and a Co-ordinator takes care of common problems. For the development of each of these documents a working group of a few world experts is first convened which prepare a preliminary draft. This draft is then reviewed by a larger, international Technical Review Committee (one for each of the five areas) and a subsequent review by the Senior Advisory Group - with representatives from 20 states - ensures that the document is well coordinated within the programme. At this stage, it is sent to Member States for comments. The Technical Review Committee concerned is reconvened to integrate these comments into the document, and, after a final review by the Senior Advisory Group, the document is ready for transmission to the Director General of the Agency for endorsement and publication. A preliminary to this procedure is the collation by the Secretariat of large amounts of information submitted by Member States so that the first draft is really based on a very complete knowledge of what is done in each area all over the world. This collation frequently reveals differences in approach which are not random but due, rather, to the local conditions and the types of reactors. These differences must be harmonized in the documents produced without detracting from the effectiveness of the code or guide. The whole

  8. SACRD: a data base for fast reactor safety computer codes, general description

    International Nuclear Information System (INIS)

    Greene, N.M.; Forsberg, V.M.; Raiford, G.B.; Arwood, J.W.; Simpson, D.B.; Flanagan, G.F.

    1979-01-01

    SACRD is a data base of material properties and other handbook data needed in computer codes used for fast reactor safety studies. Data are available in the thermodynamics, heat transfer, fluid mechanics, structural mechanics, aerosol transport, meteorology, neutronics, and dosimetry areas. Tabular, graphical and parameterized data are provided in many cases. A general description of the SACRD system is presented in the report

  9. On application of CFD codes to problems of nuclear reactor safety

    International Nuclear Information System (INIS)

    Muehlbauer, Petr

    2005-01-01

    The 'Exploratory Meeting of Experts to Define an Action Plan on the Application of Computational Fluid Dynamics (CFD) Codes to Nuclear Reactor Safety Problems' held in May 2002 at Aix-en-Province, France, recommended formation of writing groups to report the need of guidelines for use and assessment of CFD in single-phase nuclear reactor safety problems, and on recommended extensions to CFD codes to meet the needs of two-phase problems in nuclear reactor safety. This recommendations was supported also by Working Group on the Analysis and Management of Accidents and led to formation oaf three Writing Groups. The first writing Group prepared a summary of existing best practice guidelines for single phase CFD analysis and made a recommendation on the need for nuclear reactor safety specific guidelines. The second Writing Group selected those nuclear reactor safety applications for which understanding requires or is significantly enhanced by single-phase CFD analysis, and proposed a methodology for establishing assesment matrices relevant to nuclear reactor safety applications. The third writing group performed a classification of nuclear reactor safety problems where extension of CFD to two-phase flow may bring real benefit, a classification of different modeling approaches, and specification and analysis of needs in terms of physical and numerical assessments. This presentation provides a review of these activities with the most important conclusions and recommendations (Authors)

  10. Validation of the WIMSD4M cross-section generation code with benchmark results

    International Nuclear Information System (INIS)

    Deen, J.R.; Woodruff, W.L.; Leal, L.E.

    1995-01-01

    The WIMSD4 code has been adopted for cross-section generation in support of the Reduced Enrichment Research and Test Reactor (RERTR) program at Argonne National Laboratory (ANL). Subsequently, the code has undergone several updates, and significant improvements have been achieved. The capability of generating group-collapsed micro- or macroscopic cross sections from the ENDF/B-V library and the more recent evaluation, ENDF/B-VI, in the ISOTXS format makes the modified version of the WIMSD4 code, WIMSD4M, very attractive, not only for the RERTR program, but also for the reactor physics community. The intent of the present paper is to validate the WIMSD4M cross-section libraries for reactor modeling of fresh water moderated cores. The results of calculations performed with multigroup cross-section data generated with the WIMSD4M code will be compared against experimental results. These results correspond to calculations carried out with thermal reactor benchmarks of the Oak Ridge National Laboratory (ORNL) unreflected HEU critical spheres, the TRX LEU critical experiments, and calculations of a modified Los Alamos HEU D 2 O moderated benchmark critical system. The benchmark calculations were performed with the discrete-ordinates transport code, TWODANT, using WIMSD4M cross-section data. Transport calculations using the XSDRNPM module of the SCALE code system are also included. In addition to transport calculations, diffusion calculations with the DIF3D code were also carried out, since the DIF3D code is used in the RERTR program for reactor analysis and design. For completeness, Monte Carlo results of calculations performed with the VIM and MCNP codes are also presented

  11. Validation of the WIMSD4M cross-section generation code with benchmark results

    Energy Technology Data Exchange (ETDEWEB)

    Deen, J.R.; Woodruff, W.L. [Argonne National Lab., IL (United States); Leal, L.E. [Oak Ridge National Lab., TN (United States)

    1995-01-01

    The WIMSD4 code has been adopted for cross-section generation in support of the Reduced Enrichment Research and Test Reactor (RERTR) program at Argonne National Laboratory (ANL). Subsequently, the code has undergone several updates, and significant improvements have been achieved. The capability of generating group-collapsed micro- or macroscopic cross sections from the ENDF/B-V library and the more recent evaluation, ENDF/B-VI, in the ISOTXS format makes the modified version of the WIMSD4 code, WIMSD4M, very attractive, not only for the RERTR program, but also for the reactor physics community. The intent of the present paper is to validate the WIMSD4M cross-section libraries for reactor modeling of fresh water moderated cores. The results of calculations performed with multigroup cross-section data generated with the WIMSD4M code will be compared against experimental results. These results correspond to calculations carried out with thermal reactor benchmarks of the Oak Ridge National Laboratory (ORNL) unreflected HEU critical spheres, the TRX LEU critical experiments, and calculations of a modified Los Alamos HEU D{sub 2}O moderated benchmark critical system. The benchmark calculations were performed with the discrete-ordinates transport code, TWODANT, using WIMSD4M cross-section data. Transport calculations using the XSDRNPM module of the SCALE code system are also included. In addition to transport calculations, diffusion calculations with the DIF3D code were also carried out, since the DIF3D code is used in the RERTR program for reactor analysis and design. For completeness, Monte Carlo results of calculations performed with the VIM and MCNP codes are also presented.

  12. Validation of activity determination codes and nuclide vectors by using results from processing of retired components and operational waste

    International Nuclear Information System (INIS)

    Lundgren, Klas; Larsson, Arne

    2012-01-01

    Decommissioning studies for nuclear power reactors are performed in order to assess the decommissioning costs and the waste volumes as well as to provide data for the licensing and construction of the LILW repositories. An important part of this work is to estimate the amount of radioactivity in the different types of decommissioning waste. Studsvik ALARA Engineering has performed such assessments for LWRs and other nuclear facilities in Sweden. These assessments are to a large content depending on calculations, senior experience and sampling on the facilities. The precision in the calculations have been found to be relatively high close to the reactor core. Of natural reasons the precision will decline with the distance. Even if the activity values are lower the content of hard to measure nuclides can cause problems in the long term safety demonstration of LLW repositories. At the same time Studsvik is processing significant volumes of metallic and combustible waste from power stations in operation and in decommissioning phase as well as from other nuclear facilities such as research and waste treatment facilities. Combining the unique knowledge in assessment of radioactivity inventory and the large data bank the waste processing represents the activity determination codes can be validated and the waste processing analysis supported with additional data. The intention with this presentation is to highlight how the European nuclear industry jointly could use the waste processing data for validation of activity determination codes. (authors)

  13. Large leak sodium-water reaction code SWACS and its validation

    International Nuclear Information System (INIS)

    Miyake, O.; Shindo, Y.; Hiroi, H.; Tanabe, H.; Sato, M.

    1982-01-01

    A computer code SWACS for analyzing the large leak accident of an LMFBR steam generators has been developed and validated. Five tests data obtained by SWAT-3 test facility were compared with code results. In each of SWAT-3 tests, a double-ended guillotine rupture of one tube was simulated in a helical coil steam generator model with 1/2.5 scaled test vessel to the prototype SG. The analytical results, including an initial pressure spike, a propagated pressure in a secondary system, and a quasi-steady pressure, indicate that the overall large-leak event could be predicted in reasonably good agreement

  14. Proceedings of the workshop on Benchmarking of CFD Codes for Application to Nuclear Reactor Safety (CFD4NRS)

    International Nuclear Information System (INIS)

    2007-01-01

    Computational Fluid Dynamics (CFD) is to an increasing extent being adopted in nuclear reactor safety analyses as a tool that enables specific safety relevant phenomena occurring in the reactor coolant system to be better described. The Committee on the Safety of Nuclear Installations (CSNI), which is responsible for the activities of the Nuclear Energy Agency that support advancing the technical base of the safety of nuclear installations, has in recent years conducted an important activity in the CFD area. This activity has been carried out within the scope of the CSNI working group on the analysis and management of accidents (GAMA), and has mainly focused on the formulation of user guidelines and on the assessment and verification of CFD codes. It is in this GAMA framework that the present workshop was organized and carried out. The purpose of the workshop was to provide a forum for numerical analysts and experimentalists to exchange information in the field of NRS-related activities relevant to CFD validation, with the objective of providing input to GAMA CFD experts to create a practical, state-of-the-art, web-based assessment matrix on the use of CFD for NRS applications. Numerical simulations with a strong emphasis on validation were welcomed in such areas as heat transfer, buoyancy, stratification, natural circulation, free-surface modelling, turbulent mixing and multi-phase flow. These would relate to such NRS-relevant issues as: pressurized thermal shocks, boron dilution, hydrogen distribution, induced breaks, thermal striping, etc. The use of systematic error quantification and Best Practice Guidelines was encouraged. Papers reporting experiments providing high-quality data suitable for CFD validation, specifically in the area of NRS, were given high priority. Here, emphasis was placed on the availability of local measurements, especially multi-dimensional velocity measurements obtained using such techniques as laser-doppler velocimetry, hot

  15. Validation of coding algorithms for the identification of patients hospitalized for alcoholic hepatitis using administrative data.

    Science.gov (United States)

    Pang, Jack X Q; Ross, Erin; Borman, Meredith A; Zimmer, Scott; Kaplan, Gilaad G; Heitman, Steven J; Swain, Mark G; Burak, Kelly W; Quan, Hude; Myers, Robert P

    2015-09-11

    Epidemiologic studies of alcoholic hepatitis (AH) have been hindered by the lack of a validated International Classification of Disease (ICD) coding algorithm for use with administrative data. Our objective was to validate coding algorithms for AH using a hospitalization database. The Hospital Discharge Abstract Database (DAD) was used to identify consecutive adults (≥18 years) hospitalized in the Calgary region with a diagnosis code for AH (ICD-10, K70.1) between 01/2008 and 08/2012. Medical records were reviewed to confirm the diagnosis of AH, defined as a history of heavy alcohol consumption, elevated AST and/or ALT (34 μmol/L, and elevated INR. Subgroup analyses were performed according to the diagnosis field in which the code was recorded (primary vs. secondary) and AH severity. Algorithms that incorporated ICD-10 codes for cirrhosis and its complications were also examined. Of 228 potential AH cases, 122 patients had confirmed AH, corresponding to a positive predictive value (PPV) of 54% (95% CI 47-60%). PPV improved when AH was the primary versus a secondary diagnosis (67% vs. 21%; P codes for ascites (PPV 75%; 95% CI 63-86%), cirrhosis (PPV 60%; 47-73%), and gastrointestinal hemorrhage (PPV 62%; 51-73%) had improved performance, however, the prevalence of these diagnoses in confirmed AH cases was low (29-39%). In conclusion the low PPV of the diagnosis code for AH suggests that caution is necessary if this hospitalization database is used in large-scale epidemiologic studies of this condition.

  16. Application of Code Of Conduct on the Safety of Research Reactor (RTP)

    International Nuclear Information System (INIS)

    Ligam, A.S.; Ahmad Nabil Abd Rahim; Zarina Masood

    2014-01-01

    The implementation and the practices of the effective safety system at research reactors are important to ensure that the worker, public and environment do not receive any abnormal causes. Many international safety related support agencies for research reactor such as International Atomic Energy Agency (IAEA) providing guidelines that can be applied to enhance and strengthen the enforcement of safety namely Code of Conduct on the Safety of Research Reactor (IAEA/CODEOC/RR/2006). The excellent safety management, reliability, and maintainability of RTP reactor structures, coupled with personnel numerous lessons and experiences learned, Reactor TRIGA PUSPATI research reactor providing Nuclear Malaysia personnel and visitor the very safe working and visiting environment. This paper will discuss the status, practices and improvement strategies over the past few years. (author)

  17. Implementation of reactor safety analysis code CATHARE and its use on FACOM M-380

    International Nuclear Information System (INIS)

    Ishiguro, Misako; Shinozawa, Naohisa; Tomiyama, Mineyoshi; Fujisaki, Masahide

    1986-05-01

    CATHARE is an advanced safety analysis code developed at the Nuclear Research Center of Grenoble in France. The code simulates thermohydraulic phenomena involved in loss of coolant accidents in pressurized water reactors. The code has been introduced into JAERI as a part of the technical exchange between the JAERI ROSA-IV Program and the French BETHSY-CATHARE Program. The code was delivered in the form of 23 files containing 115,000 statements in total. A large part of CATHARE code has been written in an extended Fortran language 'Esope' which is mainly used for managing dynamic memory allocation. The JAERI version is created from the IBM version which has been used on Amdhal computer at ISPRA. Some modifications are required in order to implement the CATHARE code at JAERI because of difference in softwares. In this report, the overview of the code structure, the JAERI usage, the implementation method, the error correction method, the problems special to install the code in JAERI, and the distribution of computing time are described. (author)

  18. Applying Hamming Code to Memory System of Safety Grade PLC (POSAFE-Q) Processor Module

    International Nuclear Information System (INIS)

    Kim, Taehee; Hwang, Sungjae; Park, Gangmin

    2013-01-01

    If some errors such as inverted bits occur in the memory, instructions and data will be corrupted. As a result, the PLC may execute the wrong instructions or refer to the wrong data. Hamming Code can be considered as the solution for mitigating this mis operation. In this paper, we apply hamming Code, then, we inspect whether hamming code is suitable for to the memory system of the processor module. In this paper, we applied hamming code to existing safety grade PLC (POSAFE-Q). Inspection data are collected and they will be referred for improving the PLC in terms of the soundness. In our future work, we will try to improve time delay caused by hamming calculation. It will include CPLD optimization and memory architecture or parts alteration. In addition to these hamming code-based works, we will explore any methodologies such as mirroring for the soundness of safety grade PLC. Hamming code-based works can correct bit errors, but they have limitation in multi bits errors

  19. Development and Verification of the Computer Codes for the Fast Reactors Nuclear Safety Justification

    International Nuclear Information System (INIS)

    Kisselev, A.E.; Mosunova, N.A.; Strizhov, V.F.

    2015-01-01

    The information on the status of the work on development of the system of the nuclear safety codes for fast liquid metal reactors is presented in paper. The purpose of the work is to create an instrument for NPP neutronic, thermohydraulic and strength justification including human and environment radiation safety. The main task that is to be solved by the system of codes developed is the analysis of the broad spectrum of phenomena taking place on the NPP (including reactor itself, NPP components, containment rooms, industrial site and surrounding area) and analysis of the impact of the regular and accidental releases on the environment. The code system is oriented on the ability of fully integrated modeling of the NPP behavior in the coupled definition accounting for the wide range of significant phenomena taking place on the NPP under normal and accident conditions. It is based on the models that meet the state-of-the-art knowledge level. The codes incorporate advanced numerical methods and modern programming technologies oriented on the high-performance computing systems. The information on the status of the work on verification of the separate codes of the system of codes is also presented. (author)

  20. Quantitative software-reliability analysis of computer codes relevant to nuclear safety

    International Nuclear Information System (INIS)

    Mueller, C.J.

    1981-12-01

    This report presents the results of the first year of an ongoing research program to determine the probability of failure characteristics of computer codes relevant to nuclear safety. An introduction to both qualitative and quantitative aspects of nuclear software is given. A mathematical framework is presented which will enable the a priori prediction of the probability of failure characteristics of a code given the proper specification of its properties. The framework consists of four parts: (1) a classification system for software errors and code failures; (2) probabilistic modeling for selected reliability characteristics; (3) multivariate regression analyses to establish predictive relationships among reliability characteristics and generic code property and development parameters; and (4) the associated information base. Preliminary data of the type needed to support the modeling and the predictions of this program are described. Illustrations of the use of the modeling are given but the results so obtained, as well as all results of code failure probabilities presented herein, are based on data which at this point are preliminary, incomplete, and possibly non-representative of codes relevant to nuclear safety

  1. Applying Hamming Code to Memory System of Safety Grade PLC (POSAFE-Q) Processor Module

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Taehee; Hwang, Sungjae; Park, Gangmin [POSCO Nuclear Technology, Seoul (Korea, Republic of)

    2013-05-15

    If some errors such as inverted bits occur in the memory, instructions and data will be corrupted. As a result, the PLC may execute the wrong instructions or refer to the wrong data. Hamming Code can be considered as the solution for mitigating this mis operation. In this paper, we apply hamming Code, then, we inspect whether hamming code is suitable for to the memory system of the processor module. In this paper, we applied hamming code to existing safety grade PLC (POSAFE-Q). Inspection data are collected and they will be referred for improving the PLC in terms of the soundness. In our future work, we will try to improve time delay caused by hamming calculation. It will include CPLD optimization and memory architecture or parts alteration. In addition to these hamming code-based works, we will explore any methodologies such as mirroring for the soundness of safety grade PLC. Hamming code-based works can correct bit errors, but they have limitation in multi bits errors.

  2. Demonstration of Emulator-Based Bayesian Calibration of Safety Analysis Codes: Theory and Formulation

    Directory of Open Access Journals (Sweden)

    Joseph P. Yurko

    2015-01-01

    Full Text Available System codes for simulation of safety performance of nuclear plants may contain parameters whose values are not known very accurately. New information from tests or operating experience is incorporated into safety codes by a process known as calibration, which reduces uncertainty in the output of the code and thereby improves its support for decision-making. The work reported here implements several improvements on classic calibration techniques afforded by modern analysis techniques. The key innovation has come from development of code surrogate model (or code emulator construction and prediction algorithms. Use of a fast emulator makes the calibration processes used here with Markov Chain Monte Carlo (MCMC sampling feasible. This work uses Gaussian Process (GP based emulators, which have been used previously to emulate computer codes in the nuclear field. The present work describes the formulation of an emulator that incorporates GPs into a factor analysis-type or pattern recognition-type model. This “function factorization” Gaussian Process (FFGP model allows overcoming limitations present in standard GP emulators, thereby improving both accuracy and speed of the emulator-based calibration process. Calibration of a friction-factor example using a Method of Manufactured Solution is performed to illustrate key properties of the FFGP based process.

  3. A validation study of the BURNUP and associated options of the MONTE CARLO neutronics code MONK5W

    International Nuclear Information System (INIS)

    Howard, E.A.

    1985-11-01

    This is a report on the validation of the burnup option of the Monte Carlo Neutronics Code MONK5W, together with the associated facilities which allow for control rod movements and power changes. The validation uses reference solutions produced by the Deterministic Neutronics Code LWR-WIMS for a 2D model which represents a whole reactor calculation with control rod movements. (author)

  4. Quality assurance for safety in nuclear power plants. A code of practice

    International Nuclear Information System (INIS)

    1978-01-01

    The Code of Practice is a part of the International Atomic Energy Agency's programme, referred to as the NUSS programme (Nuclear Safety Standards), for establishing Codes of Practice and Safety Guides relating to land-based stationary thermal neutron power plants. The documents are based on documentation and experience from various national systems and practices. The present document provides the recommended principles and objectives for the establishment and implementation of a quality assurance programme during design, manufacture, construction, commissioning and operation of structures, system and components important to safety. They are applicable by all those responsible for the power plant, by plant designers, suppliers, architect-engineers, plant constructors, plant operators and other organizations participating in activities affecting quality. The Lists of relevant definition and the Provisional List of NUSS Programme Titles are given

  5. Validation of a new continuous Monte Carlo burnup code using a Mox fuel assembly

    International Nuclear Information System (INIS)

    El bakkari, B.; El Bardouni, T.; Merroun, O.; El Younoussi, C.; Boulaich, Y.; Boukhal, H.; Chakir, E.

    2009-01-01

    The reactivity of nuclear fuel decreases with irradiation (or burnup) due to the transformation of heavy nuclides and the formation of fission products. Burnup credit studies aim at accounting for fuel irradiation in criticality studies of the nuclear fuel cycle (transport, storage, etc...). The principal objective of this study is to evaluate the potential capabilities of a newly developed burnup code called 'BUCAL1'. BUCAL1 differs in comparison with other burnup codes as it does not use the calculated neutron flux as input to other computer codes to generate the nuclide inventory for the next time step. Instead, BUCAL1 directly uses the neutron reaction tally information generated by MCNP for each nuclide of interest to determine the new nuclides inventory. This allows the full capabilities of MCNP to be incorporated into the calculation and a more accurate and robust analysis to be performed. Validation of BUCAL1 was processed by code-to-code comparisons using predictions of several codes from the NEA/OCED. Infinite multiplication factors (k ∞ ) and important fission product and actinide concentrations were compared for a MOX core benchmark exercise. Results of calculations are analysed and discussed.

  6. Development and validation of ALEPH Monte Carlo burn-up code

    International Nuclear Information System (INIS)

    Stankovskiy, A.; Van den Eynde, G.; Vidmar, T.

    2011-01-01

    The Monte-Carlo burn-up code ALEPH is being developed in SCK-CEN since 2004. Belonging to the category of shells coupling Monte Carlo transport (MCNP or MCNPX) and 'deterministic' depletion codes (ORIGEN-2.2), ALEPH possess some unique features that distinguish it from other codes. The most important feature is full data consistency between steady-state Monte Carlo and time-dependent depletion calculations. Recent improvements of ALEPH concern full implementation of general-purpose nuclear data libraries (JEFF-3.1.1, ENDF/B-VII, JENDL-3.3). The upgraded version of the code is capable to treat isomeric branching ratios, neutron induced fission product yields, spontaneous fission yields and energy release per fission recorded in ENDF-formatted data files. The alternative algorithm for time evolution of nuclide concentrations is added. A predictor-corrector mechanism and the calculation of nuclear heating are available as well. The validation of the code on REBUS experimental programme results has been performed. The upgraded version of ALEPH has shown better agreement with measured data than other codes, including previous version of ALEPH. (authors)

  7. Validation of the 3D finite element transport theory code EVENT for shielding applications

    International Nuclear Information System (INIS)

    Warner, Paul; Oliveira, R.E. de

    2000-01-01

    This paper is concerned with the validation of the 3D deterministic neutral-particle transport theory code EVENT for shielding applications. The code is based on the finite element-spherical harmonics (FE-P N ) method which has been extensively developed over the last decade. A general multi-group, anisotropic scattering formalism enables the code to address realistic steady state and time dependent, multi-dimensional coupled neutron/gamma radiation transport problems involving high scattering and deep penetration alike. The powerful geometrical flexibility and competitive computational effort makes the code an attractive tool for shielding applications. In recognition of this, EVENT is currently in the process of being adopted by the UK nuclear industry. The theory behind EVENT is described and its numerical implementation is outlined. Numerical results obtained by the code are compared with predictions of the Monte Carlo code MCBEND and also with the results from benchmark shielding experiments. In particular, results are presented for the ASPIS experimental configuration for both neutron and gamma ray calculations using the BUGLE 96 nuclear data library. (author)

  8. Development and validation of the ENIGMA code for MOX fuel performance modelling

    International Nuclear Information System (INIS)

    Palmer, I.; Rossiter, G.; White, R.J.

    2000-01-01

    The ENIGMA fuel performance code has been under development in the UK since the mid-1980s with contributions made by both the fuel vendor (BNFL) and the utility (British Energy). In recent years it has become the principal code for UO 2 fuel licensing for both PWR and AGR reactor systems in the UK and has also been used by BNFL in support of overseas UO 2 and MOX fuel business. A significant new programme of work has recently been initiated by BNFL to further develop the code specifically for MOX fuel application. Model development is proceeding hand in hand with a major programme of MOX fuel testing and PIE studies, with the objective of producing a fuel modelling code suitable for mechanistic analysis, as well as for licensing applications. This paper gives an overview of the model developments being undertaken and of the experimental data being used to underpin and to validate the code. The paper provides a summary of the code development programme together with specific examples of new models produced. (author)

  9. Elaboration and Validation of the Medication Prescription Safety Checklist.

    Science.gov (United States)

    Pires, Aline de Oliveira Meireles; Ferreira, Maria Beatriz Guimarães; Nascimento, Kleiton Gonçalves do; Felix, Márcia Marques Dos Santos; Pires, Patrícia da Silva; Barbosa, Maria Helena

    2017-08-03

    to elaborate and validate a checklist to identify compliance with the recommendations for the structure of medication prescriptions, based on the Protocol of the Ministry of Health and the Brazilian Health Surveillance Agency. methodological research, conducted through the validation and reliability analysis process, using a sample of 27 electronic prescriptions. the analyses confirmed the content validity and reliability of the tool. The content validity, obtained by expert assessment, was considered satisfactory as it covered items that represent the compliance with the recommendations regarding the structure of the medication prescriptions. The reliability, assessed through interrater agreement, was excellent (ICC=1.00) and showed perfect agreement (K=1.00). the Medication Prescription Safety Checklist showed to be a valid and reliable tool for the group studied. We hope that this study can contribute to the prevention of adverse events, as well as to the improvement of care quality and safety in medication use. elaborar e validar um instrumento tipo checklist para identificar a adesão às recomendações na estrutura das prescrições de medicamentos, a partir do Protocolo do Ministério da Saúde e Agência Nacional de Vigilância Sanitária. pesquisa metodológica, conduzida por meio do processo de validade e análise de confiabilidade, com amostra de 27 prescrições eletrônicas. análises realizadas confirmaram a validade de conteúdo e a confiabilidade da versão do instrumento. A validade de conteúdo, obtida por meio da avaliação de juízes, foi considerada satisfatória por contemplar itens que representam a adesão às recomendações na estrutura das prescrições de medicamentos. A confiabilidade, avaliada por interobservadores, apresentou-se excelente (ICC=1,00) e de concordância perfeita (K=1,00). o instrumento Lista de Verificação de Segurança na Prescrição de Medicamentos demonstrou-se válido e confiável para o grupo estudado. Espera

  10. Criticality safety validation: Simple geometry, single unit 233U systems

    International Nuclear Information System (INIS)

    Putman, V.L.

    1997-06-01

    Typically used LMITCO criticality safety computational methods are evaluated for suitability when applied to INEEL 233 U systems which reasonably can be modeled as simple-geometry, single-unit systems. Sixty-seven critical experiments of uranium highly enriched in 233 U, including 57 aqueous solution, thermal-energy systems and 10 metal, fast-energy systems, were modeled. These experiments include 41 cylindrical and 26 spherical cores, and 41 reflected and 26 unreflected systems. No experiments were found for intermediate-neutron-energy ranges, or with interstitial non-hydrogenous materials typical of waste systems, mixed 233 U and plutonium, or reflectors such as steel, lead, or concrete. No simple geometry experiments were found with cubic or annular cores, or approximating infinite sea systems. Calculations were performed with various tools and methodologies. Nine cross-section libraries, based on ENDF/B-IV, -V, or -VI.2, or on Hansen-Roach source data, were used with cross-section processing methods of MCNP or SCALE. The k eff calculations were performed with neutral-particle transport and Monte Carlo methods of criticality codes DANT, MCNP 4A, and KENO Va

  11. Examples of Use of SINBAD Database for Nuclear Data and Code Validation

    Science.gov (United States)

    Kodeli, Ivan; Žerovnik, Gašper; Milocco, Alberto

    2017-09-01

    The SINBAD database currently contains compilations and evaluations of over 100 shielding benchmark experiments. The SINBAD database is widely used for code and data validation. Materials covered include: Air, N. O, H2O, Al, Be, Cu, graphite, concrete, Fe, stainless steel, Pb, Li, Ni, Nb, SiC, Na, W, V and mixtures thereof. Over 40 organisations from 14 countries and 2 international organisations have contributed data and work in support of SINBAD. Examples of the use of the database in the scope of different international projects, such as the Working Party on Evaluation Cooperation of the OECD and the European Fusion Programme demonstrate the merit and possible usage of the database for the validation of modern nuclear data evaluations and new computer codes.

  12. Systematic review of validated case definitions for diabetes in ICD-9-coded and ICD-10-coded data in adult populations.

    Science.gov (United States)

    Khokhar, Bushra; Jette, Nathalie; Metcalfe, Amy; Cunningham, Ceara Tess; Quan, Hude; Kaplan, Gilaad G; Butalia, Sonia; Rabi, Doreen

    2016-08-05

    With steady increases in 'big data' and data analytics over the past two decades, administrative health databases have become more accessible and are now used regularly for diabetes surveillance. The objective of this study is to systematically review validated International Classification of Diseases (ICD)-based case definitions for diabetes in the adult population. Electronic databases, MEDLINE and Embase, were searched for validation studies where an administrative case definition (using ICD codes) for diabetes in adults was validated against a reference and statistical measures of the performance reported. The search yielded 2895 abstracts, and of the 193 potentially relevant studies, 16 met criteria. Diabetes definition for adults varied by data source, including physician claims (sensitivity ranged from 26.9% to 97%, specificity ranged from 94.3% to 99.4%, positive predictive value (PPV) ranged from 71.4% to 96.2%, negative predictive value (NPV) ranged from 95% to 99.6% and κ ranged from 0.8 to 0.9), hospital discharge data (sensitivity ranged from 59.1% to 92.6%, specificity ranged from 95.5% to 99%, PPV ranged from 62.5% to 96%, NPV ranged from 90.8% to 99% and κ ranged from 0.6 to 0.9) and a combination of both (sensitivity ranged from 57% to 95.6%, specificity ranged from 88% to 98.5%, PPV ranged from 54% to 80%, NPV ranged from 98% to 99.6% and κ ranged from 0.7 to 0.8). Overall, administrative health databases are useful for undertaking diabetes surveillance, but an awareness of the variation in performance being affected by case definition is essential. The performance characteristics of these case definitions depend on the variations in the definition of primary diagnosis in ICD-coded discharge data and/or the methodology adopted by the healthcare facility to extract information from patient records. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

  13. Validation of a CFD code for Unsteady Flows with cyclic boundary Conditions

    International Nuclear Information System (INIS)

    Kim, Jong-Tae; Kim, Sang-Baik; Lee, Won-Jae

    2006-01-01

    Currently Lilac code is under development to analyze thermo-hydraulics of a high-temperature gas-cooled reactor (GCR). Interesting thermo-hydraulic phenomena in a nuclear reactor are usually unsteady and turbulent. The analysis of the unsteady flows by using a three dimension CFD code is time-consuming if the flow domain is very large. Hopefully, flow domains commonly encountered in the nuclear thermo-hydraulics is periodic. So it is better to use the geometrical characteristics in order to reduce the computational resources. To get the benefits from reducing the computation domains especially for the calculations of unsteady flows, the cyclic boundary conditions are implemented in the parallelized CFD code LILAC. In this study, the parallelized cyclic boundary conditions are validated by solving unsteady laminar and turbulent flows past a circular cylinder

  14. The COSIMA-experiments, a data base for validation of two-phase flow computer codes

    International Nuclear Information System (INIS)

    Class, G.; Meyder, R.; Stratmanns, E.

    1985-12-01

    The report presents an overview on the large data base generated with COSIMA. The data base is to be used to validate and develop computer codes for two-phase flow. In terms of fuel rod behavior it was found that during blowdown under realistic conditions only small strains are reached. For clad rupture extremely high rod internal pressure is necessary. Additionally important results were found in the behavior of a fuel rod simulator and on the effect of thermocouples attached on the cladding outer surface. Post-test calculations, performed with the codes RELAP and DRUFAN show a good agreement with the experiments. This however can be improved if the phase separation models in the codes would be updated. (orig./HP) [de

  15. Validation and uncertainty analysis of the Athlet thermal-hydraulic computer code

    International Nuclear Information System (INIS)

    Glaeser, H.

    1995-01-01

    The computer code ATHLET is being developed by GRS as an advanced best-estimate code for the simulation of breaks and transients in Pressurized Water Reactor (PWRs) and Boiling Water Reactor (BWRs) including beyond design basis accidents. A systematic validation of ATHLET is based on a well balanced set of integral and separate effects tests emphasizing the German combined Emergency Core Cooling (ECC) injection system. When using best estimate codes for predictions of reactor plant states during assumed accidents, qualification of the uncertainty in these calculations is highly desirable. A method for uncertainty and sensitivity evaluation has been developed by GRS where the computational effort is independent of the number of uncertain parameters. (author)

  16. Objective Oriented Design of Architecture for TH System Safety Analysis Code and Verification

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Bub Dong

    2008-03-15

    In this work, objective oriented design of generic system analysis code has been tried based on the previous works in KAERI for two phase three field Pilot code. It has been performed to implement of input and output design, TH solver, component model, special TH models, heat structure solver, general table, trip and control, and on-line graphics. All essential features for system analysis has been designed and implemented in the final product SYSTF code. The computer language C was used for implementation in the Visual studio 2008 IDE (Integrated Development Environment) since it has easier and lighter than C++ feature. The code has simple and essential features of models and correlation, special component, special TH model and heat structure model. However the input features is able to simulate the various scenarios, such as steady state, non LOCA transient and LOCA accident. The structure validity has been tested through the various verification tests and it has been shown that the developed code can treat the non LOCA and LOCA simulation. However more detailed design and implementation of models are required to get the physical validity of SYSTF code simulation.

  17. Objective Oriented Design of Architecture for TH System Safety Analysis Code and Verification

    International Nuclear Information System (INIS)

    Chung, Bub Dong

    2008-03-01

    In this work, objective oriented design of generic system analysis code has been tried based on the previous works in KAERI for two phase three field Pilot code. It has been performed to implement of input and output design, TH solver, component model, special TH models, heat structure solver, general table, trip and control, and on-line graphics. All essential features for system analysis has been designed and implemented in the final product SYSTF code. The computer language C was used for implementation in the Visual studio 2008 IDE (Integrated Development Environment) since it has easier and lighter than C++ feature. The code has simple and essential features of models and correlation, special component, special TH model and heat structure model. However the input features is able to simulate the various scenarios, such as steady state, non LOCA transient and LOCA accident. The structure validity has been tested through the various verification tests and it has been shown that the developed code can treat the non LOCA and LOCA simulation. However more detailed design and implementation of models are required to get the physical validity of SYSTF code simulation

  18. Validation of Mean Drift Forces Computed with the BEM Code NEMOH

    DEFF Research Database (Denmark)

    Thomsen, Jonas Bjerg

    This report covers a simple investigation of mean drift forces found by use of the boundary element method code NEMOH. The results from NEMOH are compared to analytical results from literature and to numerical values found from the commercial software package WADAM by DNV-GL. The work was conduct...... under the project ”Mooring Solutions for Large Wave Energy Converters”, during", Work Package 4: Full Dynamic Analysis". The validation compares results from a simple sphere and from a vertical cylinder....

  19. Tests for validation of fast neutron reactors safety

    International Nuclear Information System (INIS)

    Nagata, T.; Yamashita, H.

    2001-01-01

    Japanese scientific research and design enterprises in cooperation with industrial and power generating corporations implement a project on creating a fast neutron reactor of the ultimate safety. One of the basic expected results from such a development is creation of a reactor core structure that is able to eliminate recriticality occurrence in the course of reactor accident involving fuel melting. One of the possible ways to solve this problem is to include pipes (meant for specifying directed (controlled) molten fuel relocation) into fuel assembly structure. In the course of conduction and subsequent implementation of such a design the basic issue is to experimentally confirm the operating capacity of FA having such a structure and that is called FAIDUS. Within EAGLE Project on experimental basis of IAE NNC RK an activity has been started on preparation and conduction of out-of-pile and in-pile tests. During tests a sodium coolant will be used. Studies are conducted by NNC RK in cooperation with the Japanese corporations JAPC and JNC. Basic objective of out-of-pile tests was to obtain preliminary information on fuel relocation behavior under conditions simulating accident involving melting of core consisting of FAIDUS FA, which will help to clarify simulation criteria and to develop the most optimum structure of the experimental channel for reactor experiments conduction. The basic objective of in-pile tests was the experimental confirmation of operating capacity of FAIDUS FA model under reactor conditions. According to the program two tests are planned to be performed at IGR reactor: tests for validation of fast neutron reactor safety, and out-of-pile tests at EAGLE experimental facility without sodium coolant

  20. National assessment of validity of coding of acute mastoiditis: a standardised reassessment of 1966 records.

    Science.gov (United States)

    Stalfors, J; Enoksson, F; Hermansson, A; Hultcrantz, M; Robinson, Å; Stenfeldt, K; Groth, A

    2013-04-01

    To investigate the internal validity of the diagnosis code used at discharge after treatment of acute mastoiditis. Retrospective national re-evaluation study of patient records 1993-2007 and make comparison with the original ICD codes. All ENT departments at university hospitals and one large county hospital department in Sweden. A total of 1966 records were reviewed for patients with ICD codes for in-patient treatment of acute (529), chronic (44) and unspecified mastoiditis (21) and acute otitis media (1372). ICD codes were reviewed by the authors with a defined protocol for the clinical diagnosis of acute mastoiditis. Those not satisfying the diagnosis were given an alternative diagnosis. Of 529 records with ICD coding for acute mastoiditis, 397 (75%) were found to meet the definition of acute mastoiditis used in this study, while 18% were not diagnosed as having any type of mastoiditis after review. Review of the in-patients treated for acute media otitis identified an additional 60 cases fulfilling the definition of acute mastoiditis. Overdiagnosis was common, and many patients with a diagnostic code indicating acute mastoiditis had been treated for external otitis or otorrhoea with transmyringeal drainage. The internal validity of the diagnosis acute mastoiditis is dependent on the use of standardised, well-defined criteria. Reliability of diagnosis is fundamental for the comparison of results from different studies. Inadequate reliability in the diagnosis of acute mastoiditis also affects calculations of incidence rates and statistical power and may also affect the conclusions drawn from the results. © 2013 Blackwell Publishing Ltd.

  1. Validation of ASTEC v1.0 computer code against FPT2 test

    International Nuclear Information System (INIS)

    Mladenov, I.; Tusheva, P.; Kalchev, B.; Dimov, D.; Ivanov, I.

    2005-01-01

    The aim of the work is by various nodalization schemes of the model to investigate the ASTEC v1.0 computer code sensitivity and to validate the code against PHEBUS - FPT2 experiment. This code is used for severe accident analysis. The aim corresponds to the main technical objective of the experiment which is to contribute to the validation of models and computer codes to be used for the calculation of the source term in case of a severe accident in a Light Water Reactor. The objective's scope of the FPT2 is large - separately for the bundle, the experimental circuit and the containment. Additional objectives are to characterize aerosol sizing and deposition processes, and also potential FP poisoning effects on hydrogen recombiner coupons exposed to containment atmospheric conditions representative of a LWR severe accident. The analyses of the results of the performed calculations show a good accordance with the reference case calculations, and then with the experimental data. Some differences in the calculations for the thermal behavior appear locally during the oxidation phase and the heat-up phase. There is very good confirmation regarding the volatile and semi-volatile fission products release from the fuel pellets. Important for analysis of the process is the final axial distribution of the mass of fuel relocation obtained at the end of the calculation

  2. Confirm Content Validity and Sender Authenticity for Text Messages by Using QR Code

    Directory of Open Access Journals (Sweden)

    Firas Mohammed Aswad

    2018-05-01

    Full Text Available In light of the information revolution taking place in the modern world, therefore it becomes necessary and important to save this electronic messages. So we offered this technique to ensure the safety of the content of the messages and authenticity of the sender through  networks communication by converting the message's symbols to numbers , each one of this symbols (letters, numbers, symbols will converted into three digits, the first digit represents the ASCII code of the symbol , the second digit represents the frequency of this symbol in the message (the number of times this symbol is appear in the message, and the third digit represents the total number of the locations of the symbol (calculates the symbol location from the first symbol in the message to this symbol itself and blanks also calculated too .The digital signature of the sender will converted to numbers like the symbols of message we explained it before, and this numbers of the digital signature will gathering together to produce three numbers only, this number will gathering with each numbers of the message's symbols, the final  numbers will converted to QR Code , the QR Code will placed with the message and sent to the recipient. The recipient returns the steps of the sender (produce QR Code from the received message and compared it the received QR Codes, if it is match or not. The recipient will ensure that the content is secure, and confirms the authenticity of the sender.

  3. Study of the microstructure of neutron irradiated beryllium for the validation of the ANFIBE code

    International Nuclear Information System (INIS)

    Rabaglino, E.; Ferrero, C.; Reimann, J.; Ronchi, C.; Schulenberg, T.

    2002-01-01

    The behaviour of beryllium under fast neutron irradiation is a key issue of the helium cooled pebble bed tritium breeding blanket, due to the production of large quantities of helium and of a non-negligible amount of tritium. To optimise the design, a reliable prediction of swelling due to helium bubbles and of tritium inventory during normal and off-normal operation of a fusion power reactor is needed. The ANFIBE code (ANalysis of Fusion Irradiated BEryllium) is being developed to meet this need. The code has to be applied in a range of irradiation conditions where no experimental data are available, therefore a detailed gas kinetics model, and a specific and particularly careful validation strategy are needed. The validation procedure of the first version of the code was based on macroscopic data of swelling and tritium release. This approach is, however, incomplete, since a verification of the microscopic behaviour of the gas in the metal is necessary to obtain a reliable description of swelling. This paper discusses a general strategy for a thorough validation of the gas kinetics models in ANFIBE. The microstructure characterisation of weakly irradiated beryllium pebbles, with different visual examination techniques, is then presented as an example of the application of this strategy. In particular, the advantage of developing 3D techniques, such as X-ray microtomography, is demonstrated

  4. From chain liability to chain responsibility: MNE approaches to implement safety and health codes in international supply chains

    NARCIS (Netherlands)

    van Tulder, R.; van Wijk, J.; Kolk, A.

    2009-01-01

    This article examines whether the involvement of stakeholders in the design of corporate codes of conduct leads to a higher implementation likelihood of the code. The empirical focus is on Occupational Safety and Health (OSH). The article compares the inclusion of OSH issues in the codes of conduct

  5. Validation of the AZTRAN 1.1 code with problems Benchmark of LWR reactors

    International Nuclear Information System (INIS)

    Vallejo Q, J. A.; Bastida O, G. E.; Francois L, J. L.; Xolocostli M, J. V.; Gomez T, A. M.

    2016-09-01

    The AZTRAN module is a computational program that is part of the AZTLAN platform (Mexican modeling platform for the analysis and design of nuclear reactors) and that solves the neutron transport equation in 3-dimensional using the discrete ordinates method S_N, steady state and Cartesian geometry. As part of the activities of Working Group 4 (users group) of the AZTLAN project, this work validates the AZTRAN code using the 2002 Yamamoto Benchmark for LWR reactors. For comparison, the commercial code CASMO-4 and the free code Serpent-2 are used; in addition, the results are compared with the data obtained from an article of the PHYSOR 2002 conference. The Benchmark consists of a fuel pin, two UO_2 cells and two other of MOX cells; there is a problem of each cell for each type of reactor PWR and BWR. Although the AZTRAN code is at an early stage of development, the results obtained are encouraging and close to those reported with other internationally accepted codes and methodologies. (Author)

  6. Validity of the Italian Code of Ethics for everyday nursing practice.

    Science.gov (United States)

    Gobbi, Paola; Castoldi, Maria Grazia; Alagna, Rosa Anna; Brunoldi, Anna; Pari, Chiara; Gallo, Annamaria; Magri, Miriam; Marioni, Lorena; Muttillo, Giovanni; Passoni, Claudia; Torre, Anna La; Rosa, Debora; Carnevale, Franco A

    2016-12-07

    The research question for this study was as follows: Is the Code of Ethics for Nurses in Italy (Code) a valid or useful decision-making instrument for nurses faced with ethical problems in their daily clinical practice? Focus groups were conducted to analyze specific ethical problems through 11 case studies. The analysis was conducted using sections of the Code as well as other relevant documents. Each focus group had a specific theme and nurses participated freely in the discussions according to their respective clinical competencies. The executive administrative committee of the local nursing licensing council provided approval for conducting this project. Measures were taken to protect the confidentiality of consenting participants. The answer to the research question posed for this investigation was predominantly positive. Many sections of the Code were useful for discussion and identifying possible solutions for the ethical problems presented in the 11 cases. We concluded that the Code of Ethics for Nurses in Italy can be a valuable aid in daily practice in most clinical situations that can give rise to ethical problems. © The Author(s) 2016.

  7. Improvements and validation of the transient analysis code MOREL for molten salt reactors

    International Nuclear Information System (INIS)

    Zhuang Kun; Zheng Youqi; Cao Liangzhi; Hu Tianliang; Wu Hongchun

    2017-01-01

    The liquid fuel salt used in the molten salt reactors (MSRs) serves as the fuel and coolant simultaneously. On the one hand, the delayed neutron precursors circulate in the whole primary loop and part of them decay outside the core. On the other hand, the fission heat is carried off directly by the fuel flow. These two features require new analysis method with the coupling of fluid flow, heat transfer and neutronics. In this paper, the recent update of MOREL code is presented. The update includes: (1) the improved quasi-static method for the kinetics equation with convection term is developed. (2) The multi-channel thermal hydraulic model is developed based on the geometric feature of MSR. (3) The Variational Nodal Method is used to solve the neutron diffusion equation instead of the original analytic basis functions expansion nodal method. The update brings significant improvement on the efficiency of MOREL code. And, the capability of MOREL code is extended for the real core simulation with feedback. The numerical results and experiment data gained from molten salt reactor experiment (MSRE) are used to verify and validate the updated MOREL code. The results agree well with the experimental data, which prove the new development of MOREL code is correct and effective. (author)

  8. Validity of the coding for herpes simplex encephalitis in the Danish National Patient Registry

    DEFF Research Database (Denmark)

    Jørgensen, Laura Krogh; Dalgaard, Lars Skov; Østergaard, Lars Jørgen

    2016-01-01

    BACKGROUND: Large health care databases are a valuable source of infectious disease epidemiology if diagnoses are valid. The aim of this study was to investigate the accuracy of the recorded diagnosis coding of herpes simplex encephalitis (HSE) in the Danish National Patient Registry (DNPR...... (7.3%) as probable cases providing an overall PPV of 58.0% (95% confidence interval [CI]: 53.0-62.9). For "Encephalitis due to herpes simplex virus" (ICD-10 code B00.4), the PPV was 56.6% (95% CI: 51.1-62.0). Similarly, the PPV for "Meningoencephalitis due to herpes simplex virus" (ICD-10 code B00.4A......) was 56.8% (95% CI: 39.5-72.9). "Herpes viral encephalitis" (ICD-10 code G05.1E) had a PPV of 75.9% (95% CI: 56.5-89.7), thereby representing the highest PPV. The estimated sensitivity was 95.5%. CONCLUSION: The PPVs of the ICD-10 diagnosis coding for adult HSE in the DNPR were relatively low. Hence...

  9. Code of conduct on the safety and security of radioactive sources

    International Nuclear Information System (INIS)

    Anon.

    2001-01-01

    The objective of the code of conduct is to achieve and maintain a high level of safety and security of radioactive sources through the development, harmonization and enforcement of national policies, laws and regulations, and through the fostering of international co-operation. In particular, this code addresses the establishment of an adequate system of regulatory control from the production of radioactive sources to their final disposal, and a system for the restoration of such control if it has been lost. (N.C.)

  10. Thermal-Hydraulic System Codes in Nulcear Reactor Safety and Qualification Procedures

    Directory of Open Access Journals (Sweden)

    Alessandro Petruzzi

    2008-01-01

    Full Text Available In the last four decades, large efforts have been undertaken to provide reliable thermal-hydraulic system codes for the analyses of transients and accidents in nuclear power plants. Whereas the first system codes, developed at the beginning of the 1970s, utilized the homogenous equilibrium model with three balance equations to describe the two-phase flow, nowadays the more advanced system codes are based on the so-called “two-fluid model” with separation of the water and vapor phases, resulting in systems with at least six balance equations. The wide experimental campaign, constituted by the integral and separate effect tests, conducted under the umbrella of the OECD/CSNI was at the basis of the development and validation of the thermal-hydraulic system codes by which they have reached the present high degree of maturity. However, notwithstanding the huge amounts of financial and human resources invested, the results predicted by the code are still affected by errors whose origins can be attributed to several reasons as model deficiencies, approximations in the numerical solution, nodalization effects, and imperfect knowledge of boundary and initial conditions. In this context, the existence of qualified procedures for a consistent application of qualified thermal-hydraulic system code is necessary and implies the drawing up of specific criteria through which the code-user, the nodalization, and finally the transient results are qualified.

  11. Code Development on Fission Product Behavior under Severe Accident-Validation of Aerosol Sedimentation

    International Nuclear Information System (INIS)

    Ha, Kwang Soon; Kim, Sung Il; Jang, Jin Sung; Kim, Dong Ha

    2016-01-01

    The gas and aerosol phases of the radioactive materials move through the reactor coolant systems and containments as loaded on the carrier gas or liquid, such as steam or water. Most radioactive materials might escape in the form of aerosols from a nuclear power plant during a severe reactor accident, and it is very important to predict the behavior of these radioactive aerosols in the reactor cooling system and in the containment building under severe accident conditions. Aerosols are designated as very small solid particles or liquid droplets suspended in a gas phase. The suspended solid or liquid particles typically have a range of sizes of 0.01 m to 20 m. Aerosol concentrations in reactor accident analyses are typically less than 100 g/m3 and usually less than 1 g/m3. When there are continuing sources of aerosol to the gas phase or when there are complicated processes involving engineered safety features, much more complicated size distributions develop. It is not uncommon for aerosols in reactor containments to have bimodal size distributions for at least some significant periods of time early during an accident. Salient features of aerosol physics under reactor accident conditions that will affect the nature of the aerosols are (1) the formation of aerosol particles, (2) growth of aerosol particles, (3) shape of aerosol particles. At KAERI, a fission product module has been developed to predict the behaviors of the radioactive materials in the reactor coolant system under severe accident conditions. The fission product module consists of an estimation of the initial inventories, species release from the core, aerosol generation, gas transport, and aerosol transport. The final outcomes of the fission product module designate the radioactive gas and aerosol distribution in the reactor coolant system. The aerosol sedimentation models in the fission product module were validated using ABCOVE and LACE experiments. There were some discrepancies on the predicted

  12. Code Development on Fission Product Behavior under Severe Accident-Validation of Aerosol Sedimentation

    Energy Technology Data Exchange (ETDEWEB)

    Ha, Kwang Soon; Kim, Sung Il; Jang, Jin Sung; Kim, Dong Ha [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    The gas and aerosol phases of the radioactive materials move through the reactor coolant systems and containments as loaded on the carrier gas or liquid, such as steam or water. Most radioactive materials might escape in the form of aerosols from a nuclear power plant during a severe reactor accident, and it is very important to predict the behavior of these radioactive aerosols in the reactor cooling system and in the containment building under severe accident conditions. Aerosols are designated as very small solid particles or liquid droplets suspended in a gas phase. The suspended solid or liquid particles typically have a range of sizes of 0.01 m to 20 m. Aerosol concentrations in reactor accident analyses are typically less than 100 g/m3 and usually less than 1 g/m3. When there are continuing sources of aerosol to the gas phase or when there are complicated processes involving engineered safety features, much more complicated size distributions develop. It is not uncommon for aerosols in reactor containments to have bimodal size distributions for at least some significant periods of time early during an accident. Salient features of aerosol physics under reactor accident conditions that will affect the nature of the aerosols are (1) the formation of aerosol particles, (2) growth of aerosol particles, (3) shape of aerosol particles. At KAERI, a fission product module has been developed to predict the behaviors of the radioactive materials in the reactor coolant system under severe accident conditions. The fission product module consists of an estimation of the initial inventories, species release from the core, aerosol generation, gas transport, and aerosol transport. The final outcomes of the fission product module designate the radioactive gas and aerosol distribution in the reactor coolant system. The aerosol sedimentation models in the fission product module were validated using ABCOVE and LACE experiments. There were some discrepancies on the predicted

  13. Radiation protection in dentistry. Recommended safety procedures for the use of dental x-ray equipment. Safety code 30

    International Nuclear Information System (INIS)

    1994-01-01

    The Radiation Protection Bureau has prepared a series of documents on safety codes to set out requirements for the safe use of radiation-emitting equipment. This Safety Code has been prepared to provide specific guidance to the dentist, dental hygienist, dental assistant and other support personnel concerned with safety procedures and equipment performance. Dental radiography is one of the most valuable tools used in modern dental health care. It makes possible the diagnosis of physical conditions that would otherwise be difficult to identify. The use of dental radiological procedures must be carefully managed, because x-radiation has the potential for damaging healthy cells and tissues. Although no known occurrence of cancer or genetic damage has been observed from radiation doses delivered in modern dentistry, and until more evidence is available, one should practice radiation hygiene with the same care as would be dictated if a hazard were known to exist. The aim of radiation protection in dentistry is to obtain the desired clinical information with minimal radiation exposure to patients, dental personnel and the public. 15 tabs

  14. Radiation protection in dentistry. Recommended safety procedures for the use of dental x-ray equipment. Safety code 30

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    The Radiation Protection Bureau has prepared a series of documents on safety codes to set out requirements for the safe use of radiation-emitting equipment. This Safety Code has been prepared to provide specific guidance to the dentist, dental hygienist, dental assistant and other support personnel concerned with safety procedures and equipment performance. Dental radiography is one of the most valuable tools used in modern dental health care. It makes possible the diagnosis of physical conditions that would otherwise be difficult to identify. The use of dental radiological procedures must be carefully managed, because x-radiation has the potential for damaging healthy cells and tissues. Although no known occurrence of cancer or genetic damage has been observed from radiation doses delivered in modern dentistry, and until more evidence is available, one should practice radiation hygiene with the same care as would be dictated if a hazard were known to exist. The aim of radiation protection in dentistry is to obtain the desired clinical information with minimal radiation exposure to patients, dental personnel and the public. 15 tabs.

  15. Radiant Energy Measurements from a Scaled Jet Engine Axisymmetric Exhaust Nozzle for a Baseline Code Validation Case

    Science.gov (United States)

    Baumeister, Joseph F.

    1994-01-01

    A non-flowing, electrically heated test rig was developed to verify computer codes that calculate radiant energy propagation from nozzle geometries that represent aircraft propulsion nozzle systems. Since there are a variety of analysis tools used to evaluate thermal radiation propagation from partially enclosed nozzle surfaces, an experimental benchmark test case was developed for code comparison. This paper briefly describes the nozzle test rig and the developed analytical nozzle geometry used to compare the experimental and predicted thermal radiation results. A major objective of this effort was to make available the experimental results and the analytical model in a format to facilitate conversion to existing computer code formats. For code validation purposes this nozzle geometry represents one validation case for one set of analysis conditions. Since each computer code has advantages and disadvantages based on scope, requirements, and desired accuracy, the usefulness of this single nozzle baseline validation case can be limited for some code comparisons.

  16. Development and Validation of a Safety Attitude Scale for Coal Miners in China

    Directory of Open Access Journals (Sweden)

    Xiang Wu

    2017-11-01

    Full Text Available Safety attitude is of vital importance to accident prevention, and the high accident rate in the coal mining industry makes it urgent to undertake research on coal miners’ safety attitude. However, the current literature still lacks a valid and reliable safety attitude measurement scale for coal miners, which stands as a barrier against their safety attitude improvement. In this study, a scale is developed that can be used to measure coal miners’ safety attitude. The preliminary scale was based on an extended literature review. Empirical data were then collected from 725 coal miners using the preliminary scale. Both exploratory and confirmatory factor analyses were undertaken to validate and improve the scale. The final scale, which consists of 17 items, contains four dimensions: management safety commitment, team safety climate, fatalism and work pressure. Results show that this safety attitude scale can effectively measure the safety attitude of coal miners, showing high psychological measurement validity. This paper contributes to the occupational safety research by developing the factor structure and indicator system of coal miners’ safety attitude, thus providing more profound interpretation of this crucial construct in the safety research domain. The measurement scale serves as an important tool for safety attitude benchmarking among different coal mining enterprises and, thus, can boost the overall safety improvement of the whole industry. These findings can facilitate improvement of both theories and practices related to occupational safety attitude.

  17. Preliminary validation of RELAP5/Mod4.0 code for LBE cooled NACIE facility

    Energy Technology Data Exchange (ETDEWEB)

    Kumari, Indu; Khanna, Ashok, E-mail: akhanna@iitk.ac.in

    2017-04-01

    Highlights: • Detail discussion of thermo physical properties of Lead Bismuth Eutectic incorporated in the code RELAP5/Mod4.0 included. • Benchmarking of LBE properties in RELAP5/Mod4.0 against literature. • NACIE facility for three different power levels (10.8, 21.7 and 32.5 kW) under natural circulation considered for benchmarking. • Preliminary validation of the LBE properties against experimental data. • NACIE facility for power level 22.5 kW considered for validation. - Abstract: The one-dimensional thermal hydraulic computer code RELAP5 was developed for thermal hydraulic study of light water reactor as well as for nuclear research reactors. The purpose of this work is to evaluate the code RELAP5/Mod4.0 for analysis of research reactors. This paper consists of three major sections. The first section presents detailed discussions on thermo-physical properties of Lead Bismuth Eutectic (LBE) incorporated in RELAP5/Mod4.0 code. In the second section, benchmarking of RELAP5/Mod4.0 has been done with the Natural Circulation Experimental (NACIE) facility in comparison with Barone’s simulations using RELAP5/Mod3.3. Three different power levels (10.8 kW, 21.7 kW and 32.5 kW) under natural circulation conditions are considered. Results obtained for LBE temperatures, temperature difference across heat section, pin surface temperatures, mass flow rates and heat transfer coefficients in heat section heat exchanger are in agreement with Barone’s simulation results within 7% of average relative error. Third section presents validation of RELAP5/Mod4.0 against the experimental data of NACIE facility performed by Tarantino et al. test number 21 at power of 22.5 kW comparing the profiles of temperatures, mass flow rate and velocity of LBE. Simulation and experimental results agree within 7% of average relative error.

  18. Application of software engineering to development of reactor-safety codes

    International Nuclear Information System (INIS)

    Wilburn, N.P.; Niccoli, L.G.

    1980-11-01

    As a result of the drastically increasing cost of software and the lack of an engineering approach, the technology of Software Engineering is being developed. Software Engineering provides an answer to the increasing cost of developing and maintaining software. It has been applied extensively in the business and aerospace communities and is just now being applied to the development of scientific software and, in particular, to the development of reactor safety codes at HEDL

  19. First validation of the new continuous energy version of the MORET5 Monte Carlo code

    International Nuclear Information System (INIS)

    Miss, Joachim; Bernard, Franck; Forestier, Benoit; Haeck, Wim; Richet, Yann; Jacquet, Olivier

    2008-01-01

    The 5.A.1 version is the next release of the MORET Monte Carlo code dedicated to criticality and reactor calculations. This new version combines all the capabilities that are already available in the multigroup version with many new and enhanced features. The main capabilities of the previous version are the powerful association of a deterministic and Monte Carlo approach (like for instance APOLLO-MORET), the modular geometry, five source sampling techniques and two simulation strategies. The major advance in MORET5 is the ability to perform calculations either a multigroup or a continuous energy simulation. Thanks to these new developments, we now have better control over the whole process of criticality calculations, from reading the basic nuclear data to the Monte Carlo simulation itself. Moreover, this new capability enables us to better validate the deterministic-Monte Carlo multigroup calculations by performing continuous energy calculations with the same code, using the same geometry and tracking algorithms. The aim of this paper is to describe the main options available in this new release, and to present the first results. Comparisons of the MORET5 continuous-energy results with experimental measurements and against another continuous-energy Monte Carlo code are provided in terms of validation and time performance. Finally, an analysis of the interest of using a unified energy grid for continuous energy Monte Carlo calculations is presented. (authors)

  20. Development and validation of corium oxidation model for the VAPEX code

    International Nuclear Information System (INIS)

    Blinkov, V.N.; Melikhov, V.I.; Davydov, M.V.; Melikhov, O.I.; Borovkova, E.M.

    2011-01-01

    In light water reactor core melt accidents, the molten fuel (corium) can be brought into contact with coolant water in the course of the melt relocation in-vessel and ex-vessel as well as in an accident mitigation action of water addition. Mechanical energy release from such an interaction is of interest in evaluating the structural integrity of the reactor vessel as well as of the containment. Usually, the source for the energy release is considered to be the rapid transfer of heat from the molten fuel to the water ('vapor explosion'). When the fuel contains a chemically reactive metal component, there could be an additional source for the energy release, which is the heat release and hydrogen production due to the metal-water chemical reaction. In Electrogorsk Research and Engineering Center the computer code VAPEX (VAPor EXplosion) has been developed for analysis of the molten fuel coolant interaction. Multifield approach is used for modeling of dynamics of following phases: water, steam, melt jet, melt droplets, debris. The VAPEX code was successfully validated on FARO experimental data. Hydrogen generation was observed in FARO tests even though corium didn't contain metal component. The reason for hydrogen generation was not clear, so, simplified empirical model of hydrogen generation was implemented in the VAPEX code to take into account input of hydrogen into pressure increase. This paper describes new more detailed model of hydrogen generation due to the metal-water chemical reaction and results of its validation on ZREX experiments. (orig.)

  1. Validation of ICD-9-CM coding algorithm for improved identification of hypoglycemia visits

    Directory of Open Access Journals (Sweden)

    Lieberman Rebecca M

    2008-04-01

    Full Text Available Abstract Background Accurate identification of hypoglycemia cases by International Classification of Diseases, Ninth Revision, Clinical Modification (ICD-9-CM codes will help to describe epidemiology, monitor trends, and propose interventions for this important complication in patients with diabetes. Prior hypoglycemia studies utilized incomplete search strategies and may be methodologically flawed. We sought to validate a new ICD-9-CM coding algorithm for accurate identification of hypoglycemia visits. Methods This was a multicenter, retrospective cohort study using a structured medical record review at three academic emergency departments from July 1, 2005 to June 30, 2006. We prospectively derived a coding algorithm to identify hypoglycemia visits using ICD-9-CM codes (250.3, 250.8, 251.0, 251.1, 251.2, 270.3, 775.0, 775.6, and 962.3. We confirmed hypoglycemia cases by chart review identified by candidate ICD-9-CM codes during the study period. The case definition for hypoglycemia was documented blood glucose 3.9 mmol/l or emergency physician charted diagnosis of hypoglycemia. We evaluated individual components and calculated the positive predictive value. Results We reviewed 636 charts identified by the candidate ICD-9-CM codes and confirmed 436 (64% cases of hypoglycemia by chart review. Diabetes with other specified manifestations (250.8, often excluded in prior hypoglycemia analyses, identified 83% of hypoglycemia visits, and unspecified hypoglycemia (251.2 identified 13% of hypoglycemia visits. The absence of any predetermined co-diagnosis codes improved the positive predictive value of code 250.8 from 62% to 92%, while excluding only 10 (2% true hypoglycemia visits. Although prior analyses included only the first-listed ICD-9 code, more than one-quarter of identified hypoglycemia visits were outside this primary diagnosis field. Overall, the proposed algorithm had 89% positive predictive value (95% confidence interval, 86–92 for

  2. Radiation physics and shielding codes and analyses applied to design-assist and safety analyses of CANDUR and ACRTM reactors

    International Nuclear Information System (INIS)

    Aydogdu, K.; Boss, C. R.

    2006-01-01

    heavily on experience and engineering judgement, consistent with the ALARA philosophy. Special care is taken to ensure that the best estimate dose rates are used to the extent possible when applying ALARA. Provisions for safeguards equipment are made throughout the fuel-handling route in CANDU and ACR reactors. For example, the fuel bundle counters rely on the decay gammas from the fission products in spent-fuel bundles to record the number of fuel movements. The International Atomic Energy Agency (IAEA) Safeguards system for CANDU and ACR reactors is based on item (fuel bundle) accounting. It involves a combination of IAEA inspection with containment and surveillance, and continuous unattended monitoring. The spent fuel bundle counter monitors spent fuel bundles as they are transferred from the fuelling machine to the spent fuel bay. The shielding and dose-rate analysis need to be carried out so that the bundle counter functions properly. This paper includes two codes used in criticality safety analyses. Criticality safety is a unique phenomenon and codes that address criticality issues will demand specific validations. However, it is recognised that some of the codes used in radiation physics will also be used in criticality safety assessments. (authors)

  3. TOOKUIL: A case study in user interface development for safety code application

    International Nuclear Information System (INIS)

    Gray, D.L.; Harkins, C.K.; Hoole, J.G.

    1997-01-01

    Traditionally, there has been a very high learning curve associated with using nuclear power plant (NPP) analysis codes. Even for seasoned plant analysts and engineers, the process of building or modifying an input model for present day NPP analysis codes is tedious, error prone, and time consuming. Current cost constraints and performance demands place an additional burden on today's safety analysis community. Advances in graphical user interface (GUI) technology have been applied to obtain significant productivity and quality assurance improvements for the Transient Reactor Analysis Code (TRAC) input model development. KAPL Inc. has developed an X Windows-based graphical user interface named TOOKUIL which supports the design and analysis process, acting as a preprocessor, runtime editor, help system, and post processor for TRAC. This paper summarizes the objectives of the project, the GUI development process and experiences, and the resulting end product, TOOKUIL

  4. TOOKUIL: A case study in user interface development for safety code application

    International Nuclear Information System (INIS)

    Gray, D.L.; Harkins, C.K.; Hoole, J.G.; Peebles, R.C.; Smith, R.J.

    1996-11-01

    Traditionally, there has been a very high learning curve associated with using nuclear power plant (NPP) analysis codes. Even for seasoned plant analysts and engineers, the process of building or modifying an input model for present day NPP analysis codes is tedious, error prone, and time consuming. Current cost constraints and performance demands place an additional burden on today's safety analysis community. Advances in graphical user interface (GUI) technology have been applied to obtain significant productivity and quality assurance improvements for the Transient Reactor Analysis Code (TRAC) input model development. KAPL Inc. has developed an X Windows-based graphical user interface named TOOKUIL which supports the design and analysis process, acting as a preprocessor, runtime editor, help system, and post processor for TRAC. This paper summarizes the objectives of the project, the GUI development process and experiences, and the resulting end product, TOOKUIL

  5. TOOKUIL: A case study in user interface development for safety code application

    Energy Technology Data Exchange (ETDEWEB)

    Gray, D.L.; Harkins, C.K.; Hoole, J.G. [and others

    1997-07-01

    Traditionally, there has been a very high learning curve associated with using nuclear power plant (NPP) analysis codes. Even for seasoned plant analysts and engineers, the process of building or modifying an input model for present day NPP analysis codes is tedious, error prone, and time consuming. Current cost constraints and performance demands place an additional burden on today`s safety analysis community. Advances in graphical user interface (GUI) technology have been applied to obtain significant productivity and quality assurance improvements for the Transient Reactor Analysis Code (TRAC) input model development. KAPL Inc. has developed an X Windows-based graphical user interface named TOOKUIL which supports the design and analysis process, acting as a preprocessor, runtime editor, help system, and post processor for TRAC. This paper summarizes the objectives of the project, the GUI development process and experiences, and the resulting end product, TOOKUIL.

  6. Code of conduct on the safety and security of radioactive sources

    International Nuclear Information System (INIS)

    2004-01-01

    The objectives of the Code of Conduct are, through the development, harmonization and implementation of national policies, laws and regulations, and through the fostering of international co-operation, to: (i) achieve and maintain a high level of safety and security of radioactive sources; (ii) prevent unauthorized access or damage to, and loss, theft or unauthorized transfer of, radioactive sources, so as to reduce the likelihood of accidental harmful exposure to such sources or the malicious use of such sources to cause harm to individuals, society or the environment; and (iii) mitigate or minimize the radiological consequences of any accident or malicious act involving a radioactive source. These objectives should be achieved through the establishment of an adequate system of regulatory control of radioactive sources, applicable from the stage of initial production to their final disposal, and a system for the restoration of such control if it has been lost. This Code relies on existing international standards relating to nuclear, radiation, radioactive waste and transport safety and to the control of radioactive sources. It is intended to complement existing international standards in these areas. The Code of Conduct serves as guidance in general issues, legislation and regulations, regulatory bodies as well as import and export of radioactive sources. A list of radioactive sources covered by the code is provided which includes activities corresponding to thresholds of categories

  7. Safety in nuclear power plant operation, including commissioning and decommissioning. A code of practice

    International Nuclear Information System (INIS)

    1978-01-01

    Safe operation of a nuclear power plant postulates satisfactory siting, design, construction and commissioning, together with proper management and operation of the plant. This Code of Practice deals with the safety aspects of management, commissioning, operation and decommissioning of the plant. It forms part of the Agency's programme, referred to as the NUSS programme, for establishing Codes of Practice and Safety Guides relating to land-based stationary thermal neutron power plants. It has been prepared for the use of those responsible for the operation of stationary nuclear power plants, the main function of which is the generation of electrical and/or thermal power, and for the use of those responsible for regulating the operation of such plants. It is not intended for application to reactors used solely for experimental or research purposes. The provisions in the Code are designed to provide assurance that operational activities are carried out without undue radiological hazard to the general public and to persons on the site. It should be understood that the provisions in the Code set forth minimum requirements which shall be met in order to achieve safe operation of a nuclear power plant

  8. Code of conduct on the safety and security of radioactive sources

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-01-01

    The objectives of the Code of Conduct are, through the development, harmonization and implementation of national policies, laws and regulations, and through the fostering of international co-operation, to: (i) achieve and maintain a high level of safety and security of radioactive sources; (ii) prevent unauthorized access or damage to, and loss, theft or unauthorized transfer of, radioactive sources, so as to reduce the likelihood of accidental harmful exposure to such sources or the malicious use of such sources to cause harm to individuals, society or the environment; and (iii) mitigate or minimize the radiological consequences of any accident or malicious act involving a radioactive source. These objectives should be achieved through the establishment of an adequate system of regulatory control of radioactive sources, applicable from the stage of initial production to their final disposal, and a system for the restoration of such control if it has been lost. This Code relies on existing international standards relating to nuclear, radiation, radioactive waste and transport safety and to the control of radioactive sources. It is intended to complement existing international standards in these areas. The Code of Conduct serves as guidance in general issues, legislation and regulations, regulatory bodies as well as import and export of radioactive sources. A list of radioactive sources covered by the code is provided which includes activities corresponding to thresholds of categories.

  9. Interactive computer codes for education and training on nuclear safety and radioprotection

    International Nuclear Information System (INIS)

    Leszczynski, Francisco

    2008-01-01

    Two interactive computer codes for education and training on nuclear safety and radioprotection developed at RA6 Reactor Division-Bariloche Atomic Center-CNEA are presented on this paper. The first code named SIMREACT has been developed in order to simulate the control of a research nuclear reactor in real time with a simple but accurate approach. The code solves the equations of neutron punctual kinetics with time variable reactivity. Utilizing the timer of the computer and the controls of a PC keyboard, with an adequate graphic interface, a simulation in real time of the temporal behavior of a research reactor is obtained. The reactivity can be changed by means of the extraction or insertion of control rods. It was implemented also the simulation of automatic pilot and scram. The use of this code is focalized on practices of nuclear reactor control like start-up from the subcritical state with external source up to power to a desired level, change of power level, calibration of a control rod with different methods, and approach to critical condition by interpolation of the answer in function of reactivity. The second code named LICEN has been developed in order to help the studies of all the topics included in examination programs for obtaining licenses for research reactor operators and radioprotection officials. Using the PC mouse, with an adequate graphic interface, the student can gradually learn the topics related with general and special licenses. The general option includes nuclear reactor engineering, radioprotection, nuclear safety, documentation and normative. The specific option includes mandatory documentation, description of the installation and task on normal and emergency situations. For each of these topics there are sub-items with all the relevant information. The objective of this code is to joint in one electronic place a large amount of information which usually it is disseminated on difficult to find separated papers. (author)

  10. Revised IAEA Code of Conduct on the Safety and Security of Radioactive Sources

    International Nuclear Information System (INIS)

    Wheatley, J. S.

    2004-01-01

    The revised Code of Conduct on the Safety and Security of Radioactive Sources is aimed primarily at Governments, with the objective of achieving and maintaining a high level of safety and security of radioactive sources through the development, harmonization and enforcement of national policies, laws and regulations; and through the fostering of international co-operation. It focuses on sealed radioactive sources and provides guidance on legislation, regulations and the regulatory body, and import/export controls. Nuclear materials (except for sources containing 239Pu), as defined in the Convention on the Physical Protection of Nuclear Materials, are not covered by the revised Code, nor are radioactive sources within military or defence programmes. An earlier version of the Code was published by IAEA in 2001. At that time, agreement was not reached on a number of issues, notably those relating to the creation of comprehensive national registries for radioactive sources, obligations of States exporting radioactive sources, and the possibility of unilateral declarations of support. The need to further consider these and other issues was highlighted by the events of 11th September 2001. Since then, the IAEA's Secretariat has been working closely with Member States and relevant International Organizations to achieve consensus. The text of the revised Code was finalized at a meeting of technical and legal experts in August 2003, and it was submitted to IAEA's Board of Governors for approval in September 2003, with a recommendation that the IAEA General Conference adopt it and encourage its wide implementation. The IAEA General Conference, in September 2003, endorsed the revised Code and urged States to work towards following the guidance contained within it. This paper summarizes the history behind the revised Code, its content and the outcome of the discussions within the IAEA Board of Governors and General Conference. (Author) 8 refs

  11. Development, validation and application of NAFA 2D-CFD code

    International Nuclear Information System (INIS)

    Vaidya, A.M.; Maheshwari, N.K.; Vijayan, P.K.; Saha, D.

    2010-01-01

    A 2D axi-symmetric code named NAFA (Version 1.0) is developed for studying the pipe flow under various conditions. It can handle laminar/ turbulent flows, with or without heat transfer, under sub-critical/super-critical conditions. The code solves for momentum, energy equations with standard k-ε turbulence model (with standard wall functions). It solves pipe flow subjected to 'velocity inlet', 'wall', 'axis' and 'pressure outlet' boundary conditions. It is validated for several cases by comparing its results with experimental data/analytical solutions/correlations. The code has excellent convergence characteristics as verified from fall of equation residual in each case. It has proven capability of generating mesh independent results for laminar as well as turbulent flows. The code is applied to supercritical flows. For supercritical flows, the effect of mesh size on prediction of heat transfer coefficient is studied. With grid refinement, the Y + reduces and reaches the limiting value of 11.63. Hence the accuracy is found to increase with grid refinement. NAFA is able to qualitatively predict the effect of heat flux and operating pressure on heat transfer coefficient. The heat transfer coefficient matches well with experimental values under various conditions. (author)

  12. Independent validation testing of the FLAME computer code, Version 1.0

    International Nuclear Information System (INIS)

    Martian, P.; Chung, J.N.

    1992-07-01

    Independent testing of the FLAME computer code, Version 1.0, was conducted to determine if the code is ready for use in hydrological and environmental studies at Department of Energy sites. This report describes the technical basis, approach, and results of this testing. Validation tests, (i.e., tests which compare field data to the computer generated solutions) were used to determine the operational status of the FLAME computer code and were done on a qualitative basis through graphical comparisons of the experimental and numerical data. These tests were specifically designed to check: (1) correctness of the FORTRAN coding, (2) computational accuracy, and (3) suitability to simulating actual hydrologic conditions. This testing was performed using a structured evaluation protocol which consisted of: (1) independent applications, and (2) graduated difficulty of test cases. Three tests ranging in complexity from simple one-dimensional steady-state flow field problems under near-saturated conditions to two-dimensional transient flow problems with very dry initial conditions

  13. Thyc, a 3D thermal-hydraulic code for rod bundles. Recent developments and validation tests

    International Nuclear Information System (INIS)

    Caremoli, C.; Rascle, P.; Aubry, S.; Olive, J.

    1993-09-01

    PWR or LMFBR cores or fuel assemblies, PWR steam generators, condensers, tubular heat exchangers, are basic components of a nuclear power plant involving two-phase flows in tube or rod bundles. A deep knowledge of the detailed flow patterns on the shell side is necessary to evaluate DNB margins in reactor cores, singularity effects (grids, wire spacers, support plates, baffles), corrosion on steam generator tube sheet, bypass effects and vibration risks. For that purpose, Electricite de France has developed, since 1986, a general purpose code named THYC (Thermal HYdraulic Code) designed to study three-dimensional single and two phase flows in rod or tube bundles (pressurized water reactor cores, steam generators, condensers, heat exchangers). It considers the three-dimensional domain to contain two kinds of components: fluid and solids. The THYC model is obtained by space-time averaging of the instantaneous equations (mass, momentum and energy) of each phase over control volumes including fluid and solids. This paper briefly presents the physical model and the numerical method used in THYC. Then, validation tests (comparison with experiments) and applications (coupling with three-dimensional neutronics code and DNB predictions) are presented. They emphasize the last developments and new capabilities of the code. (authors). 10 figs., 3 tabs., 21 refs

  14. Experimental validation for combustion analysis of GOTHIC code in 2-dimensional combustion chamber

    International Nuclear Information System (INIS)

    Lee, J. W.; Yang, S. Y.; Park, K. C.; Jung, S. H.

    2002-01-01

    In this study, the prediction capability of GOTHIC code for hydrogen combustion phenomena was validated with the results of two-dimensional premixed hydrogen combustion experiment executed by Seoul National University. The experimental chamber has about 24 liter free volume (1x0.024x1 m 3 ) and 2-dimensional rectangular shape. The test were preformed with 10% hydrogen/air gas mixture and conducted with combination of two igniter positions (top center, top corner) and two boundary conditions (bottom full open, bottom right half open). Using the lumped parameter and mechanistic combustion model in GOTHIC code, the SNU experiments were simulated under the same conditions. The GOTHIC code prediction of the hydrogen combustion phenomena did not compare well with the experimental results. In case of lumped parameter simulation, the combustion time was predicted appropriately. But any other local information related combustion phenomena could not be obtained. In case of mechanistic combustion analysis, the physical combustion phenomena of gas mixture were not matched experimental ones. In boundary open cases, the GOTHIC predicted very long combustion time and the flame front propagation could not simulate appropriately. Though GOTHIC showed flame propagation phenomenon in adiabatic calculation, the induction time of combustion was still very long compare with experimental results. Also, it was found that the combustion model of GOTHIC code had some weak points in low concentration of hydrogen combustion simulation

  15. Validation of TEMP: A finite line heat transfer code for geologic repositories for nuclear waste

    International Nuclear Information System (INIS)

    Atterbury, W.G.; Hetteburg, J.R.; Wurm, K.J.

    1987-09-01

    TEMP is a FORTRAN computer code for calculating temperatures in a geologic repository for nuclear waste. A previous report discusses the structure, usage, verification, and benchmarking of TEMP V1.0 (Wurm et al., 1987). This report discusses modifications to the program in the development of TEMP V1.1 and documents the validation of TEMP. The development of TEMP V1.1 from TEMP V1.0 consisted of two major efforts. The first was to recode several of the subroutines to improve logic flow and to allow for geometry-independent temperature calculation routines which, in turn, allowed for the addition of the geometry-independent validation option. The validation option provides TEMP with the ability to model any geometry of temperature sources with any step-wise heat release rate. This capability allows TEMP to model the geometry and heat release characteristics of the validation problems. The validation of TEMP V1.1 consists of the comparison of TEMP to three in-ground heater tests. The three tests chosen were Avery Island, Louisiana, Site A; Avery Island, Louisiana, Site C; and Asse Mine, Federal Republic of Germany, Site 2. TEMP shows marginal comparison with the two Avery Island sites and good comparison with the Asse Mine Site. 8 refs., 25 figs., 14 tabs

  16. Off-take Model of the SPACE Code and Its Validation

    International Nuclear Information System (INIS)

    Oh, Myung Taek; Park, Chan Eok; Sohn, Jong Joo

    2011-01-01

    Liquid entrainment and vapor pull-through models of horizontal pipe have been implemented in the SPACE code. The model of SPACE accounts for the phase separation phenomena and computes the flux of mass and energy through an off-take attached to a horizontal pipe when stratified conditions occur in the horizontal pipe. This model is referred to as the off-take model. The importance of predicting the fluid conditions through an off-take in a small-break LOCA has been well known. In this case, the occurrence of the stratification can affect the break node void fraction and thus the break flow discharged from the primary system. In order to validate the off-take model newly developed for the SPACE code, a simulation of the HDU experiments has been performed. The main feature of the off-take model and its application results will be presented in this paper

  17. Stochastic methods for uncertainty treatment of functional variables in computer codes: application to safety studies

    International Nuclear Information System (INIS)

    Nanty, Simon

    2015-01-01

    This work relates to the framework of uncertainty quantification for numerical simulators, and more precisely studies two industrial applications linked to the safety studies of nuclear plants. These two applications have several common features. The first one is that the computer code inputs are functional and scalar variables, functional ones being dependent. The second feature is that the probability distribution of functional variables is known only through a sample of their realizations. The third feature, relative to only one of the two applications, is the high computational cost of the code, which limits the number of possible simulations. The main objective of this work was to propose a complete methodology for the uncertainty analysis of numerical simulators for the two considered cases. First, we have proposed a methodology to quantify the uncertainties of dependent functional random variables from a sample of their realizations. This methodology enables to both model the dependency between variables and their link to another variable, called co-variate, which could be, for instance, the output of the considered code. Then, we have developed an adaptation of a visualization tool for functional data, which enables to simultaneously visualize the uncertainties and features of dependent functional variables. Second, a method to perform the global sensitivity analysis of the codes used in the two studied cases has been proposed. In the case of a computationally demanding code, the direct use of quantitative global sensitivity analysis methods is intractable. To overcome this issue, the retained solution consists in building a surrogate model or meta model, a fast-running model approximating the computationally expensive code. An optimized uniform sampling strategy for scalar and functional variables has been developed to build a learning basis for the meta model. Finally, a new approximation approach for expensive codes with functional outputs has been

  18. The Use of Coupled Code Technique for Best Estimate Safety Analysis of Nuclear Power Plants

    International Nuclear Information System (INIS)

    Bousbia Salah, A.; D'Auria, F.

    2006-01-01

    Issues connected with the thermal-hydraulics and neutronics of nuclear plants still challenge the design, safety and the operation of Light Water nuclear Reactors (LWR). The lack of full understanding of complex mechanisms related to the interaction between these issues imposed the adoption of conservative safety limits. Those safety margins put restrictions on the optimal exploitation of the plants and consequently reduced economic profit of the plant. In the light of the sustained development in computer technology, the possibilities of code capabilities have been enlarged substantially. Consequently, advanced safety evaluations and design optimizations that were not possible few years ago can now be performed. In fact, during the last decades Best Estimate (BE) neutronic and thermal-hydraulic calculations were so far carried out following rather parallel paths with only few interactions between them. Nowadays, it becomes possible to switch to new generation of computational tools, namely, Coupled Code technique. The application of such method is mandatory for the analysis of accident conditions where strong coupling between the core neutronics and the primary circuit thermal-hydraulics, and more especially when asymmetrical processes take place in the core leading to local space-dependent power generation. Through the current study, a demonstration of the maturity level achieved in the calculation of 3-D core performance during complex accident scenarios in NPPs is emphasized. Typical applications are outlined and discussed showing the main features and limitations of this technique. (author)

  19. The use of case tools in OPG safety analysis code qualification

    International Nuclear Information System (INIS)

    Pascoe, J.; Cheung, A.; Westbye, C.

    2001-01-01

    Ontario Power Generation (OPG) is currently qualifying its critical safety analysis software. The software quality assurance (SQA) framework is described. Given the legacy nature of much of the safety analysis software the reverse engineering methodology has been adopted. The safety analysis suite of codes was developed over a period of many years to differing standards of quality and had sparse or incomplete documentation. Key elements of the reverse engineering process require recovery of design information from existing coding. This recovery, if performed manually, could represent an enormous effort. Driven by a need to maximize productivity and enhance the repeatability and objectivity of software qualification activities the decision was made to acquire or develop and implement Computer Aided Software Engineering (CASE) tools. This paper presents relevant background information on CASE tools and discusses how the OPG SQA requirements were used to assess the suitability of available CASE tools. Key findings from the application of CASE tools to the qualification of the OPG safety analysis software are discussed. (author)

  20. Workforce perceptions of hospital safety culture: development and validation of the patient safety climate in healthcare organizations survey.

    Science.gov (United States)

    Singer, Sara; Meterko, Mark; Baker, Laurence; Gaba, David; Falwell, Alyson; Rosen, Amy

    2007-10-01

    To describe the development of an instrument for assessing workforce perceptions of hospital safety culture and to assess its reliability and validity. Primary data collected between March 2004 and May 2005. Personnel from 105 U.S. hospitals completed a 38-item paper and pencil survey. We received 21,496 completed questionnaires, representing a 51 percent response rate. Based on review of existing safety climate surveys, we developed a list of key topics pertinent to maintaining a culture of safety in high-reliability organizations. We developed a draft questionnaire to address these topics and pilot tested it in four preliminary studies of hospital personnel. We modified the questionnaire based on experience and respondent feedback, and distributed the revised version to 42,249 hospital workers. We randomly divided respondents into derivation and validation samples. We applied exploratory factor analysis to responses in the derivation sample. We used those results to create scales in the validation sample, which we subjected to multitrait analysis (MTA). We identified nine constructs, three organizational factors, two unit factors, three individual factors, and one additional factor. Constructs demonstrated substantial convergent and discriminant validity in the MTA. Cronbach's alpha coefficients ranged from 0.50 to 0.89. It is possible to measure key salient features of hospital safety climate using a valid and reliable 38-item survey and appropriate hospital sample sizes. This instrument may be used in further studies to better understand the impact of safety climate on patient safety outcomes.

  1. Validity of administrative database code algorithms to identify vascular access placement, surgical revisions, and secondary patency.

    Science.gov (United States)

    Al-Jaishi, Ahmed A; Moist, Louise M; Oliver, Matthew J; Nash, Danielle M; Fleet, Jamie L; Garg, Amit X; Lok, Charmaine E

    2018-03-01

    We assessed the validity of physician billing codes and hospital admission using International Classification of Diseases 10th revision codes to identify vascular access placement, secondary patency, and surgical revisions in administrative data. We included adults (≥18 years) with a vascular access placed between 1 April 2004 and 31 March 2013 at the University Health Network, Toronto. Our reference standard was a prospective vascular access database (VASPRO) that contains information on vascular access type and dates of placement, dates for failure, and any revisions. We used VASPRO to assess the validity of different administrative coding algorithms by calculating the sensitivity, specificity, and positive predictive values of vascular access events. The sensitivity (95% confidence interval) of the best performing algorithm to identify arteriovenous access placement was 86% (83%, 89%) and specificity was 92% (89%, 93%). The corresponding numbers to identify catheter insertion were 84% (82%, 86%) and 84% (80%, 87%), respectively. The sensitivity of the best performing coding algorithm to identify arteriovenous access surgical revisions was 81% (67%, 90%) and specificity was 89% (87%, 90%). The algorithm capturing arteriovenous access placement and catheter insertion had a positive predictive value greater than 90% and arteriovenous access surgical revisions had a positive predictive value of 20%. The duration of arteriovenous access secondary patency was on average 578 (553, 603) days in VASPRO and 555 (530, 580) days in administrative databases. Administrative data algorithms have fair to good operating characteristics to identify vascular access placement and arteriovenous access secondary patency. Low positive predictive values for surgical revisions algorithm suggest that administrative data should only be used to rule out the occurrence of an event.

  2. Current status and applications of intergrated safety assessment and simulation code system for ISA

    Energy Technology Data Exchange (ETDEWEB)

    Izquierdo, J. M.; Hortal, J.; Perea, M. Sanchez; Melendez, E. [Modeling and Simulation Area (MOSI), Nuclear Safety Council (CSN), Madrid (Spain); Queral, E.; Rivas-Lewicky, J. [Energy and Fuels Department, Technical University of Madrid (UPM), Madrid (Spain)

    2017-03-15

    This paper reviews current status of the unified approach known as integrated safety assessment (ISA), as well as the associated SCAIS (simulation codes system for ISA) computer platform. These constitute a proposal, which is the result of collaborative action among the Nuclear Safety Council (CSN), University of Madrid (UPM), and NFQ Solutions S.L, aiming to allow independent regulatory verification of industry quantitative risk assessments. The content elaborates on discussions of the classical treatment of time in conventional probabilistic safety assessment (PSA) sequences and states important conclusions that can be used to avoid systematic and unacceptable underestimation of the failure exceedance frequencies. The unified ISA method meets this challenge by coupling deterministic and probabilistic mutual influences. The feasibility of the approach is illustrated with some examples of its application to a real size plant.

  3. Validation of full core geometry model of the NODAL3 code in the PWR transient Benchmark problems

    International Nuclear Information System (INIS)

    T-M Sembiring; S-Pinem; P-H Liem

    2015-01-01

    The coupled neutronic and thermal-hydraulic (T/H) code, NODAL3 code, has been validated in some PWR static benchmark and the NEACRP PWR transient benchmark cases. However, the NODAL3 code have not yet validated in the transient benchmark cases of a control rod assembly (CR) ejection at peripheral core using a full core geometry model, the C1 and C2 cases. By this research work, the accuracy of the NODAL3 code for one CR ejection or the unsymmetrical group of CRs ejection case can be validated. The calculations by the NODAL3 code have been carried out by the adiabatic method (AM) and the improved quasistatic method (IQS). All calculated transient parameters by the NODAL3 code were compared with the reference results by the PANTHER code. The maximum relative difference of 16 % occurs in the calculated time of power maximum parameter by using the IQS method, while the relative difference of the AM method is 4 % for C2 case. All calculation results by the NODAL3 code shows there is no systematic difference, it means the neutronic and T/H modules are adopted in the code are considered correct. Therefore, all calculation results by using the NODAL3 code are very good agreement with the reference results. (author)

  4. Validation and optimisation of an ICD-10-coded case definition for sepsis using administrative health data

    Science.gov (United States)

    Jolley, Rachel J; Jetté, Nathalie; Sawka, Keri Jo; Diep, Lucy; Goliath, Jade; Roberts, Derek J; Yipp, Bryan G; Doig, Christopher J

    2015-01-01

    Objective Administrative health data are important for health services and outcomes research. We optimised and validated in intensive care unit (ICU) patients an International Classification of Disease (ICD)-coded case definition for sepsis, and compared this with an existing definition. We also assessed the definition's performance in non-ICU (ward) patients. Setting and participants All adults (aged ≥18 years) admitted to a multisystem ICU with general medicosurgical ICU care from one of three tertiary care centres in the Calgary region in Alberta, Canada, between 1 January 2009 and 31 December 2012 were included. Research design Patient medical records were randomly selected and linked to the discharge abstract database. In ICU patients, we validated the Canadian Institute for Health Information (CIHI) ICD-10-CA (Canadian Revision)-coded definition for sepsis and severe sepsis against a reference standard medical chart review, and optimised this algorithm through examination of other conditions apparent in sepsis. Measures Sensitivity (Sn), specificity (Sp), positive predictive value (PPV) and negative predictive value (NPV) were calculated. Results Sepsis was present in 604 of 1001 ICU patients (60.4%). The CIHI ICD-10-CA-coded definition for sepsis had Sn (46.4%), Sp (98.7%), PPV (98.2%) and NPV (54.7%); and for severe sepsis had Sn (47.2%), Sp (97.5%), PPV (95.3%) and NPV (63.2%). The optimised ICD-coded algorithm for sepsis increased Sn by 25.5% and NPV by 11.9% with slightly lowered Sp (85.4%) and PPV (88.2%). For severe sepsis both Sn (65.1%) and NPV (70.1%) increased, while Sp (88.2%) and PPV (85.6%) decreased slightly. Conclusions This study demonstrates that sepsis is highly undercoded in administrative data, thus under-ascertaining the true incidence of sepsis. The optimised ICD-coded definition has a higher validity with higher Sn and should be preferentially considered if used for surveillance purposes. PMID:26700284

  5. Modeling the Relationship between Safety Climate and Safety Performance in a Developing Construction Industry: A Cross-Cultural Validation Study.

    Science.gov (United States)

    Zahoor, Hafiz; Chan, Albert P C; Utama, Wahyudi P; Gao, Ran; Zafar, Irfan

    2017-03-28

    This study attempts to validate a safety performance (SP) measurement model in the cross-cultural setting of a developing country. In addition, it highlights the variations in investigating the relationship between safety climate (SC) factors and SP indicators. The data were collected from forty under-construction multi-storey building projects in Pakistan. Based on the results of exploratory factor analysis, a SP measurement model was hypothesized. It was tested and validated by conducting confirmatory factor analysis on calibration and validation sub-samples respectively. The study confirmed the significant positive impact of SC on safety compliance and safety participation , and negative impact on number of self-reported accidents/injuries . However, number of near-misses could not be retained in the final SP model because it attained a lower standardized path coefficient value. Moreover, instead of safety participation , safety compliance established a stronger impact on SP. The study uncovered safety enforcement and promotion as a novel SC factor, whereas safety rules and work practices was identified as the most neglected factor. The study contributed to the body of knowledge by unveiling the deviations in existing dimensions of SC and SP. The refined model is expected to concisely measure the SP in the Pakistani construction industry, however, caution must be exercised while generalizing the study results to other developing countries.

  6. Real-time validation of receiver state information in optical space-time block code systems.

    Science.gov (United States)

    Alamia, John; Kurzweg, Timothy

    2014-06-15

    Free space optical interconnect (FSOI) systems are a promising solution to interconnect bottlenecks in high-speed systems. To overcome some sources of diminished FSOI performance caused by close proximity of multiple optical channels, multiple-input multiple-output (MIMO) systems implementing encoding schemes such as space-time block coding (STBC) have been developed. These schemes utilize information pertaining to the optical channel to reconstruct transmitted data. The STBC system is dependent on accurate channel state information (CSI) for optimal system performance. As a result of dynamic changes in optical channels, a system in operation will need to have updated CSI. Therefore, validation of the CSI during operation is a necessary tool to ensure FSOI systems operate efficiently. In this Letter, we demonstrate a method of validating CSI, in real time, through the use of moving averages of the maximum likelihood decoder data, and its capacity to predict the bit error rate (BER) of the system.

  7. Validating the Danish adaptation of the World Health Organization's International Classification for Patient Safety classification of patient safety incident types

    DEFF Research Database (Denmark)

    Mikkelsen, Kim Lyngby; Thommesen, Jacob; Andersen, Henning Boje

    2013-01-01

    Objectives Validation of a Danish patient safety incident classification adapted from the World Health Organizaton's International Classification for Patient Safety (ICPS-WHO). Design Thirty-three hospital safety management experts classified 58 safety incident cases selected to represent all types.......513 (range: 0.193–0.804). Kappa and ICC showed high correlation (r = 0.99). An inverse correlation was found between the prevalence of type and inter-rater reliability. Results are discussed according to four factors known to determine the inter-rater agreement: skill and motivation of raters; clarity...

  8. Validation of simulation codes for future systems: motivations, approach, and the role of nuclear data

    International Nuclear Information System (INIS)

    Palmiotti, G.; Salvatores, M.; Aliberti, G.

    2007-01-01

    The validation of advanced simulation tools will still play a very significant role in several areas of reactor system analysis. This is the case of reactor physics and neutronics, where nuclear data uncertainties still play a crucial role for many core and fuel cycle parameters. The present paper gives a summary of validation motivations, objectives and approach. A validation effort is in particular necessary in the frame of advanced (e.g. Generation-IV or GNEP) reactors and associated fuel cycles assessment and design. Validation of simulation codes is complementary to the 'verification' process. In fact, 'verification' addresses the question 'are we solving the equations correctly' while validation addresses the question 'are we solving the correct equations with the correct parameters'. Verification implies comparisons with 'reference' equation solutions or with analytical solutions, when they exist. Most of what is called 'numerical validation' falls in this category. Validation strategies differ according to the relative weight of the methods and of the parameters that enter into the simulation tools. Most validation is based on experiments, and the field of neutronics where a 'robust' physics description model exists and which is function of 'input' parameters not fully known, will be the focus of this paper. In fact, in the case of reactor core, shielding and fuel cycle physics the model (theory) is well established (the Boltzmann and Bateman equations) and the parameters are the nuclear cross-sections, decay data etc. Two types of validation approaches can and have been used: (a) Mock-up experiments ('global' validation): need for a very close experimental simulation of a reference configuration. Bias factors cannot be extrapolated beyond reference configuration; (b) Use of 'clean', 'representative' integral experiments ('bias factor and adjustment' method). Allows to define bias factors, uncertainties and can be used for a wide range of applications. It

  9. Concurrent validation of an inertial measurement system to quantify kicking biomechanics in four football codes.

    Science.gov (United States)

    Blair, Stephanie; Duthie, Grant; Robertson, Sam; Hopkins, William; Ball, Kevin

    2018-05-17

    Wearable inertial measurement systems (IMS) allow for three-dimensional analysis of human movements in a sport-specific setting. This study examined the concurrent validity of a IMS (Xsens MVN system) for measuring lower extremity and pelvis kinematics in comparison to a Vicon motion analysis system (MAS) during kicking. Thirty footballers from Australian football (n = 10), soccer (n = 10), rugby league and rugby union (n = 10) clubs completed 20 kicks across four conditions. Concurrent validity was assessed using a linear mixed-modelling approach, which allowed the partition of between and within-subject variance from the device measurement error. Results were expressed in raw and standardised units for assessments of differences in means and measurement error, and interpreted via non-clinical magnitude-based inferences. Trivial to small differences were found in linear velocities (foot and pelvis), angular velocities (knee, shank and thigh), sagittal joint (knee and hip) and segment angle (shank and pelvis) means (mean difference: 0.2-5.8%) between the IMS and MAS in Australian football, soccer and the rugby codes. Trivial to small measurement errors (from 0.1 to 5.8%) were found between the IMS and MAS in all kinematic parameters. The IMS demonstrated acceptable levels of concurrent validity compared to a MAS when measuring kicking biomechanics across the four football codes. Wearable IMS offers various benefits over MAS, such as, out-of-laboratory testing, larger measurement range and quick data output, to help improve the ecological validity of biomechanical testing and the timing of feedback. The results advocate the use of IMS to quantify biomechanics of high-velocity movements in sport-specific settings. Copyright © 2018 Elsevier Ltd. All rights reserved.

  10. The TALL-3D facility design and commissioning tests for validation of coupled STH and CFD codes

    Energy Technology Data Exchange (ETDEWEB)

    Grishchenko, Dmitry, E-mail: dmitry@safety.sci.kth.se; Jeltsov, Marti, E-mail: marti@safety.sci.kth.se; Kööp, Kaspar, E-mail: kaspar@safety.sci.kth.se; Karbojian, Aram, E-mail: karbojan@kth.se; Villanueva, Walter, E-mail: walter@safety.sci.kth.se; Kudinov, Pavel, E-mail: pavel@safety.sci.kth.se

    2015-08-15

    Highlights: • Design of a heavy liquid thermal-hydraulic loop for CFD/STH code validation. • Description of the loop instrumentation and assessment of measurement error. • Experimental data from forced to natural circulation transient. - Abstract: Application of coupled CFD (Computational Fluid Dynamics) and STH (System Thermal Hydraulics) codes is a prerequisite for computationally affordable and sufficiently accurate prediction of thermal-hydraulics of complex systems. Coupled STH and CFD codes require validation for understanding and quantification of the sources of uncertainties in the code prediction. TALL-3D is a liquid Lead Bismuth Eutectic (LBE) loop developed according to the requirements for the experimental data for validation of coupled STH and CFD codes. The goals of the facility design are to provide (i) mutual feedback between natural circulation in the loop and complex 3D mixing and stratification phenomena in the pool-type test section, (ii) a possibility to validate standalone STH and CFD codes for each subsection of the facility, and (iii) sufficient number of experimental data to separate the process of input model calibration and code validation. Description of the facility design and its main components, approach to estimation of experimental uncertainty and calibration of model input parameters that are not directly measured in the experiment are discussed in the paper. First experimental data from the forced to natural circulation transient is also provided in the paper.

  11. Validation of the XLACS code related to contribution of resolved and unresolved resonances and background cross sections

    International Nuclear Information System (INIS)

    Anaf, J.; Chalhoub, E.S.

    1990-01-01

    The procedures for calculating contributions of resolved and unresolved resonances and background cross sections, in XLACS code, were revised. Constant weighting function and zero Kelvin temperature were considered. Discrepancies found were corrected and now the validated XLACS code generates results that are correct and in accordance with its originally established procedures. (author)

  12. Validation of the MCNP-DSP Monte Carlo code for calculating source-driven noise parameters of subcritical systems

    International Nuclear Information System (INIS)

    Valentine, T.E.; Mihalczo, J.T.

    1995-01-01

    This paper describes calculations performed to validate the modified version of the MCNP code, the MCNP-DSP, used for: the neutron and photon spectra of the spontaneous fission of californium 252; the representation of the detection processes for scattering detectors; the timing of the detection process; and the calculation of the frequency analysis parameters for the MCNP-DSP code

  13. Relative validity of the pre-coded food diary used in the Danish National Survey of Diet and Physical Activity

    DEFF Research Database (Denmark)

    Knudsen, Vibeke Kildegaard; Gille, Maj-Britt; Nielsen, Trine Holmgaard

    2011-01-01

    Objective: To determine the relative validity of the pre-coded food diary applied in the Danish National Survey of Dietary Habits and Physical Activity. Design: A cross-over study among seventy-two adults (aged 20 to 69 years) recording diet by means of a pre-coded food diary over 4 d and a 4 d...

  14. Validation of Safety-Critical Systems for Aircraft Loss-of-Control Prevention and Recovery

    Science.gov (United States)

    Belcastro, Christine M.

    2012-01-01

    Validation of technologies developed for loss of control (LOC) prevention and recovery poses significant challenges. Aircraft LOC can result from a wide spectrum of hazards, often occurring in combination, which cannot be fully replicated during evaluation. Technologies developed for LOC prevention and recovery must therefore be effective under a wide variety of hazardous and uncertain conditions, and the validation framework must provide some measure of assurance that the new vehicle safety technologies do no harm (i.e., that they themselves do not introduce new safety risks). This paper summarizes a proposed validation framework for safety-critical systems, provides an overview of validation methods and tools developed by NASA to date within the Vehicle Systems Safety Project, and develops a preliminary set of test scenarios for the validation of technologies for LOC prevention and recovery

  15. Cross-validation of an employee safety climate model in Malaysia.

    Science.gov (United States)

    Bahari, Siti Fatimah; Clarke, Sharon

    2013-06-01

    Whilst substantial research has investigated the nature of safety climate, and its importance as a leading indicator of organisational safety, much of this research has been conducted with Western industrial samples. The current study focuses on the cross-validation of a safety climate model in the non-Western industrial context of Malaysian manufacturing. The first-order factorial validity of Cheyne et al.'s (1998) [Cheyne, A., Cox, S., Oliver, A., Tomas, J.M., 1998. Modelling safety climate in the prediction of levels of safety activity. Work and Stress, 12(3), 255-271] model was tested, using confirmatory factor analysis, in a Malaysian sample. Results showed that the model fit indices were below accepted levels, indicating that the original Cheyne et al. (1998) safety climate model was not supported. An alternative three-factor model was developed using exploratory factor analysis. Although these findings are not consistent with previously reported cross-validation studies, we argue that previous studies have focused on validation across Western samples, and that the current study demonstrates the need to take account of cultural factors in the development of safety climate models intended for use in non-Western contexts. The results have important implications for the transferability of existing safety climate models across cultures (for example, in global organisations) and highlight the need for future research to examine cross-cultural issues in relation to safety climate. Copyright © 2013 National Safety Council and Elsevier Ltd. All rights reserved.

  16. Safety studies of plasma-wall events with AINA code for Japanese DEMO

    Energy Technology Data Exchange (ETDEWEB)

    Rivas, J.C., E-mail: jose.carlos.rivas@upc.edu [International Fusion Energy Research Centre (IFERC) (Japan); Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia-BarcelonaTech (Spain); Nakamura, M.; Someya, Y.; Hoshino, K.; Asakura, N. [Japan Atomic Energy Agency (JAEA) (Japan); Takase, H. [International Fusion Energy Research Centre (IFERC) (Japan); Miyoshi, Y.; Utoh, H.; Tobita, K. [Japan Atomic Energy Agency (JAEA) (Japan); Dies, J.; Blas, A. de; Riego, A.; Fabbri, M. [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia-BarcelonaTech (Spain)

    2016-11-01

    Highlights: • Work done in AINA code during 2014 and 2015 at IFERC to develop a version for safety studies of a Japanese DEMO design. • A thermal model for a WCPB breeding blanket has been developed based in parametric input data from neutronics calculations. • A breakthrough for the safety studies of plasma-divertor transients: An integrated SOL-pedestal model + using melting time as objective variable + using optimization algorithm. • The results for the case of divertor show that both loss of plasma control (LOPC) transients and ex-vessel LOCA transient can induce severe melting. The difference is that while in the first case melting happens at PFC surface, in the second case it happens at copper heat sink. • Conclusions suggest that, because the minimum melting times are same order of magnitude than the energy confinement time, recovery time for plasma control system should be lower order. - Abstract: In this contribution, the work done in AINA code during 2014 and 2015 at IFERC is presented. The main motivation of this work was to adapt the code and to perform safety studies for a Japanese DEMO design. Related to AINA code, the work has supposed major changes in plasma models. Significant is the addition of an integrated SOL-pedestal model that allows the estimation of heat loads at divertor. Also, a thermal model for a WCPB (water cooled pebble bed) breeding blanket has been developed based in parametric input data from neutronics calculations. Related to safety studies, a major breakthrough in the study of LOPC (loss of plasma control) transients has been the use of an optimization method to determine the most severe transients in terms of the shortest melting times. The results of the safety study show that LOPC transients are not likely to be severe for breeding blanket, but for the case of divertor can induce severe melting. For ex-vessel LOCA (loss of coolant accident) analysis, it is severe for both blanket and divertor, but in the first case

  17. Safety studies of plasma-wall events with AINA code for Japanese DEMO

    International Nuclear Information System (INIS)

    Rivas, J.C.; Nakamura, M.; Someya, Y.; Hoshino, K.; Asakura, N.; Takase, H.; Miyoshi, Y.; Utoh, H.; Tobita, K.; Dies, J.; Blas, A. de; Riego, A.; Fabbri, M.

    2016-01-01

    Highlights: • Work done in AINA code during 2014 and 2015 at IFERC to develop a version for safety studies of a Japanese DEMO design. • A thermal model for a WCPB breeding blanket has been developed based in parametric input data from neutronics calculations. • A breakthrough for the safety studies of plasma-divertor transients: An integrated SOL-pedestal model + using melting time as objective variable + using optimization algorithm. • The results for the case of divertor show that both loss of plasma control (LOPC) transients and ex-vessel LOCA transient can induce severe melting. The difference is that while in the first case melting happens at PFC surface, in the second case it happens at copper heat sink. • Conclusions suggest that, because the minimum melting times are same order of magnitude than the energy confinement time, recovery time for plasma control system should be lower order. - Abstract: In this contribution, the work done in AINA code during 2014 and 2015 at IFERC is presented. The main motivation of this work was to adapt the code and to perform safety studies for a Japanese DEMO design. Related to AINA code, the work has supposed major changes in plasma models. Significant is the addition of an integrated SOL-pedestal model that allows the estimation of heat loads at divertor. Also, a thermal model for a WCPB (water cooled pebble bed) breeding blanket has been developed based in parametric input data from neutronics calculations. Related to safety studies, a major breakthrough in the study of LOPC (loss of plasma control) transients has been the use of an optimization method to determine the most severe transients in terms of the shortest melting times. The results of the safety study show that LOPC transients are not likely to be severe for breeding blanket, but for the case of divertor can induce severe melting. For ex-vessel LOCA (loss of coolant accident) analysis, it is severe for both blanket and divertor, but in the first case

  18. Evaluation of temporary non-code repairs in safety class 3 piping systems

    International Nuclear Information System (INIS)

    Godha, P.C.; Kupinski, M.; Azevedo, N.F.

    1996-01-01

    Temporary non-ASME Code repairs in safety class 3 pipe and piping components are permissible during plant operation in accordance with Nuclear Regulatory Commission Generic Letter 90-05. However, regulatory acceptance of such repairs requires the licensee to undertake several timely actions. Consistent with the requirements of GL 90-05, this paper presents an overview of the detailed evaluation and relief request process. The technical criteria encompasses both ductile and brittle piping materials. It also lists appropriate evaluation methods that a utility engineer can select to perform a structural integrity assessment for design basis loading conditions to support the use of temporary non-Code repair for degraded piping components. Most use of temporary non-code repairs at a nuclear generating station is in the service water system which is an essential safety related system providing the ultimate heat sink for various plant systems. Depending on the plant siting, the service water system may use fresh water or salt water as the cooling medium. Various degradation mechanisms including general corrosion, erosion/corrosion, pitting, microbiological corrosion, galvanic corrosion, under-deposit corrosion or a combination thereof continually challenge the pressure boundary structural integrity. A good source for description of corrosion degradation in cooling water systems is provided in a cited reference

  19. Experiences using IAEA Code of practice for radiation sterilization of tissue allografts: Validation and routine control

    Energy Technology Data Exchange (ETDEWEB)

    Hilmy, N. [Batan Research Tissue Bank (BRTB), Centre for Research and Development of Isotopes and Radiation Technology, P.O. Box 7002, JKSKL, Jakarta 12070 (Indonesia)], E-mail: nazly@batan.go.id; Febrida, A.; Basril, A. [Batan Research Tissue Bank (BRTB), Centre for Research and Development of Isotopes and Radiation Technology, P.O. Box 7002, JKSKL, Jakarta 12070 (Indonesia)

    2007-11-15

    Problems of tissue allografts in using International Standard (ISO) 11137 for validation of radiation sterilization dose (RSD) are limited and low numbers of uniform samples per production batch, those are products obtained from one donor. Allograft is a graft transplanted between two different individuals of the same species. The minimum number of uniform samples needed for verification dose (VD) experiment at the selected sterility assurance level (SAL) per production batch according to the IAEA Code is 20, i.e., 10 for bio-burden determination and the remaining 10 for sterilization test. Three methods of the IAEA Code have been used for validation of RSD, i.e., method A1 that is a modification of method 1 of ISO 11137:1995, method B (ISO 13409:1996), and method C (AAMI TIR 27:2001). This paper describes VD experiments using uniform products obtained from one cadaver donor, i.e., cancellous bones, demineralized bone powders and amnion grafts from one life donor. Results of the verification dose experiments show that RSD is 15.4 kGy for cancellous and demineralized bone grafts and 19.2 kGy for amnion grafts according to method A1 and 25 kGy according to methods B and C.

  20. Development and validation of gui based input file generation code for relap

    International Nuclear Information System (INIS)

    Anwar, M.M.; Khan, A.A.; Chughati, I.R.; Chaudri, K.S.; Inyat, M.H.; Hayat, T.

    2009-01-01

    Reactor Excursion and Leak Analysis Program (RELAP) is a widely acceptable computer code for thermal hydraulics modeling of Nuclear Power Plants. It calculates thermal- hydraulic transients in water-cooled nuclear reactors by solving approximations to the one-dimensional, two-phase equations of hydraulics in an arbitrarily connected system of nodes. However, the preparation of input file and subsequent analysis of results in this code is a tedious task. The development of a Graphical User Interface (GUI) for preparation of the input file for RELAP-5 is done with the validation of GUI generated Input File. The GUI is developed in Microsoft Visual Studio using Visual C Sharp (C) as programming language. The Nodalization diagram is drawn graphically and the program contains various component forms along with the starting data form, which are launched for properties assignment to generate Input File Cards serving as GUI for the user. The GUI is provided with Open / Save function to store and recall the Nodalization diagram along with Components' properties. The GUI generated Input File is validated for several case studies and individual component cards are compared with the originally required format. The generated Input File of RELAP is found consistent with the requirement of RELAP. The GUI provided a useful platform for simulating complex hydrodynamic problems efficiently with RELAP. (author)

  1. Validation of two-phase flow code THYC on VATICAN experiment

    International Nuclear Information System (INIS)

    Maurel, F.; Portesse, A.; Rimbert, P.; Thomas, B.

    1997-01-01

    As part of a comprehensive program for THYC validation (THYC is a 3-dimensional two-phase flow computer code for PWR core configuration), an experimental project > has been initiated by the Direction des Etudes et Recherches of Electricite de France. Two mock-ups tested in Refrigerant-114, VATICAN-1 (with simple space grids) and VATICAN-2 (with mixing grids) were set up to investigate void fraction distributions using a single beam gamma densitometer. First, experiments were conducted with the VATICAN-1 mock-up. A set of constitutive laws to be used in rod bundles was determined but some doubts still remain for friction losses closure laws for oblique flow over tubes. From VATICAN-2 tests, calculations were performed using the standard set of correlations. Comparison with the experimental data shows an underprediction of void fraction by THYC in disturbed regions. Analyses highlight the poor treatment of axial relative velocity in these regions. A fitting of the radial and axial relative velocity values in the disturbed region improves the prediction of void fraction by the code but without any physical explanation. More analytical experiments should be carried out to validate friction losses closure laws for oblique flows and relative velocity downstream of a mixing grid. (author)

  2. Validation of two-phase flow code THYC on VATICAN experiment

    Energy Technology Data Exchange (ETDEWEB)

    Maurel, F.; Portesse, A.; Rimbert, P.; Thomas, B. [EDF/DER, Dept. TTA, 78 - Chatou (France)

    1997-12-31

    As part of a comprehensive program for THYC validation (THYC is a 3-dimensional two-phase flow computer code for PWR core configuration), an experimental project <> has been initiated by the Direction des Etudes et Recherches of Electricite de France. Two mock-ups tested in Refrigerant-114, VATICAN-1 (with simple space grids) and VATICAN-2 (with mixing grids) were set up to investigate void fraction distributions using a single beam gamma densitometer. First, experiments were conducted with the VATICAN-1 mock-up. A set of constitutive laws to be used in rod bundles was determined but some doubts still remain for friction losses closure laws for oblique flow over tubes. From VATICAN-2 tests, calculations were performed using the standard set of correlations. Comparison with the experimental data shows an underprediction of void fraction by THYC in disturbed regions. Analyses highlight the poor treatment of axial relative velocity in these regions. A fitting of the radial and axial relative velocity values in the disturbed region improves the prediction of void fraction by the code but without any physical explanation. More analytical experiments should be carried out to validate friction losses closure laws for oblique flows and relative velocity downstream of a mixing grid. (author)

  3. Development of the methodology and approaches to validate safety and accident management

    International Nuclear Information System (INIS)

    Asmolov, V.G.

    1997-01-01

    The article compares the development of the methodology and approaches to validate the nuclear power plant safety and accident management in Russia and advanced industrial countries. It demonstrates that the development of methods of safety validation is dialectically related to the accumulation of the knowledge base on processes and events during NPP normal operation, transients and emergencies, including severe accidents. The article describes the Russian severe accident research program (1987-1996), the implementation of which allowed Russia to reach the world level of the safety validation efforts, presents future high-priority study areas. Problems related to possible approaches to the methodological accident management development are discussed. (orig.)

  4. First analysis of AGS0, LT2 and E9 CABRI tests with the new SFR safety code ASTEC-Na

    International Nuclear Information System (INIS)

    Perez-Martin, Sara; Bandini, Giacomino; Matuzas, Vaidas; Buck, Michael; Girault, Nathalie

    2015-01-01

    Within the framework of the European JASMIN project, the ASTEC-Na code is being developed for safety analysis of severe accidents in SFR. In the first phase of validation of the ASTEC-Na fuel thermo-mechanical models three in-pile tests conducted in the CABRI experimental reactor have been selected to be analysed. We present here the preliminary results of the simulation of two Transient Over Power tests and one power ramp test (AGS0, LT2 and E9, respectively) where no pin failure occurred during the transient. We present the comparison of ASTEC-Na results against experimental data and other safety code results for the initial steady state conditions prior to the transient onset as well as for the fuel pin behaviour during the transients. (author)

  5. The data requirements for the verification and validation of a fuel performance code - the transuranus perspective

    International Nuclear Information System (INIS)

    Schubert, A.; Di Marcello, V.; Rondinella, V.; Van De Laar, J.; Van Uffelen, P.

    2013-01-01

    In general, the verification and validation (V and V) of a fuel performance code like TRANSURANUS consists of three basic steps: a) verifying the correctness and numerical stability of the sub-models; b) comparing the sub-models with experimental data; c) comparing the results of the integral fuel performance code with experimental data Only the second and third steps of the V and V rely on experimental information. This scheme can be further detailed according to the physical origin of the data: on one hand, in-reactor ('in-pile') experimental data are generated in the course of the irradiation; on the other hand ex-reactor ('out-of-pile') experimental data are obtained for instance from various postirradiation examinations (PIE) or dedicated experiments with fresh samples. For both categories, we will first discuss the V and V of sub-models of TRANSURANUS related to separate aspects of the fuel behaviour: this includes the radial variation of the composition and fissile isotopes, the thermal properties of the fuel (e.g. thermal conductivity, melting temperature, etc.), the mechanical properties of fuel and cladding (e.g. elastic constants, creep properties), as well as the models for the fission product behaviour. Secondly, the integral code verification will be addressed as it treats various aspects of the fuel behaviour, including the geometrical changes in the fuel and the gas pressure and composition of the free volume in the rod. (authors)

  6. Validation of the metal fuel version of the SAS4A accident analysis code

    International Nuclear Information System (INIS)

    Tentner, A.M.

    1991-01-01

    This paper describes recent work directed towards the validation of the metal fuel version of the SAS4A accident analysis code. The SAS4A code system has been developed at Argonne National Laboratory for the simulation of hypothetical severe accidents in Liquid Metal-Cooled Reactors (LMR), designed to operate in a fast neutron spectrum. SAS4A was initially developed for the analysis of oxide-fueled liquid metal-cooled reactors and has played an important role in the simulation and assessment of the energetics potential for postulated severe accidents in these reactors. Due to the current interest in the metal-fueled liquid metal-cooled reactors, a metal fuel version of the SAS4A accident analysis code is being developed in the Integral Fast Reactor program at Argonne. During such postulated accident scenarios as the unprotected (i.e. without scram) loss-of-flow and transient overpower events, a large number of interrelated physical phenomena occur during a relatively short time. These phenomena include transient heat transfer and hydrodynamic events, coolant boiling, and fuel and cladding melting and relocation. Due to strong neutronic feedbacks these events can significantly influence the reactor power history in the accident progression. The paper presents the results of a recent SAS4A simulation of the M7 TREAT experiment. 6 refs., 5 figs

  7. Validation of the ASSERT subchannel code for MAPLE-X10 reactor conditions

    International Nuclear Information System (INIS)

    Carver, M.B.; Kiteley, J.C.; Junop, S.V.; Wasilewicz, J.F.

    1993-01-01

    The ASSERT subchannel analysis code has been developed specifically to model flow and phase distributions within CANDU fuel channels. Recently, ASSERT has been adapted for use in simulating the MAPLE-X10 reactor. ASSERT uses an advanced drift-flux model, which permits the phases to have unequal velocities and unequal temperatures (UVUT), and thus can model non-equilibrium effects such as phase separation tendencies and subcooled boiling. Modelling subcooled boiling accurately is particularly important for MAPLE-X10. This paper briefly summarizes the non-equilibrium model used in the ASSERT code, the equations used to represent these models, and the algorithms used to solve the equations numerically. Very few modifications to the ASSERT models were needed to address MAPLE conditions. These centered on the manner in which finned fuel rods are treated, and they are discussed in the paper. The paper also gives results from validation exercises, in which the ASSERT code predictions of subcooled boiling void-fraction and critical heat flux were compared to experiments using MAPLE-X10 finned fuel elements in annuli and various bundles. 18 refs., 13 figs., 3 tabs

  8. Validations of BWR nuclear design code using ABWR MOX numerical benchmark problems

    International Nuclear Information System (INIS)

    Takano, Shou; Sasagawa, Masaru; Yamana, Teppei; Ikehara, Tadashi; Yanagisawa, Naoki

    2017-01-01

    BWR core design code package (the HINES assembly code and the PANACH core simulator), being used for full MOX-ABWR core design, has been benchmarked against the high-fidelity numerical solutions as references, for the purpose of validating its capability of predicting the BWR core design parameters systematically from UO 2 to 100% MOX cores. The reference solutions were created by whole core critical calculations using MCNPs with the precisely modeled ABWR cores both in hot and cold conditions at BOC and EOC of the equilibrium cycle. A Doppler-Broadening Rejection Correction (DCRB) implemented MCNP5-1.4 with ENDF/B-VII.0 was mainly used to evaluate the core design parameters, except for effective delayed neutron fraction (β eff ) and prompt neutron lifetime (l) with MCNP6.1. The discrepancies in the results between the design codes HINES-PANACH and MCNPs for the core design parameters such as the bundle powers, hot pin powers, control rod worth, boron worth, void reactivity, Doppler reactivity, β eff and l, are almost within target accuracy, leading to the conclusion that HINES-PANACH has sufficient fidelity for application to full MOX-ABWR core design. (author)

  9. Validation and configuration management plan for the KE basins KE-PU spreadsheet code

    International Nuclear Information System (INIS)

    Harris, R.A.

    1996-01-01

    This report provides documentation of the spreadsheet KE-PU software that is used to verify compliance with the Operational Safety Requirement and Process Standard limit on the amount of plutonium in the KE-Basin sandfilter backwash pit. Included are: A summary of the verification of the method and technique used in KE-PU that were documented elsewhere, the requirements, plans, and results of validation tests that confirm the proper functioning of the software, the procedures and approvals required to make changes to the software, and the method used to maintain configuration control over the software

  10. FY2017 Updates to the SAS4A/SASSYS-1 Safety Analysis Code

    Energy Technology Data Exchange (ETDEWEB)

    Fanning, T. H. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2017-09-30

    The SAS4A/SASSYS-1 safety analysis software is used to perform deterministic analysis of anticipated events as well as design-basis and beyond-design-basis accidents for advanced fast reactors. It plays a central role in the analysis of U.S. DOE conceptual designs, proposed test and demonstration reactors, and in domestic and international collaborations. This report summarizes the code development activities that have taken place during FY2017. Extensions to the void and cladding reactivity feedback models have been implemented, and Control System capabilities have been improved through a new virtual data acquisition system for plant state variables and an additional Block Signal for a variable lag compensator to represent reactivity feedback for novel shutdown devices. Current code development and maintenance needs are also summarized in three key areas: software quality assurance, modeling improvements, and maintenance of related tools. With ongoing support, SAS4A/SASSYS-1 can continue to fulfill its growing role in fast reactor safety analysis and help solidify DOE’s leadership role in fast reactor safety both domestically and in international collaborations.

  11. Current algorithms used in reactor safety codes and the impact of future computer development on these algorithms

    International Nuclear Information System (INIS)

    Mahaffy, J.H.; Liles, D.R.; Woodruff, S.B.

    1985-01-01

    Computational methods and solution procedures used in the US Nuclear Regulatory Commission's reactor safety systems codes, Transient Reactor Analysis Code (TRAC) and Reactor Leak and Power Safety Excursion Code (RELAP), are reviewed. Methods used in TRAC-PF1/MOD1, including the stability-enhancing two-step (SETS) technique, which permits fast computations by allowing time steps larger than the material Courant stability limit, are described in detail, and the differences from RELAP5/MOD2 are noted. Developments in computing, including parallel and vector processing, and their applicability to nuclear reactor safety codes are described. These developments, coupled with appropriate numerical methods, make detailed faster-than-real-time reactor safety analysis a realistic near-term possibility

  12. Authorization request for potential non-compliance with the American Standard Safety Code for Elevators Dumbwaiters and Escalators

    Energy Technology Data Exchange (ETDEWEB)

    Boyd, J.E.

    1964-09-28

    A Third Party inspection of the reactor work platforms was conducted by representatives of the Travelers Insurance Company in 1958. An inspection report submitted by these representatives described hazardous conditions noted and presented a series of recommendations to improve the operational safety of the systems. Project CGI-960, ``C`` & ``D`` Work Platform Safety Improvements -- All Reactors, vas initiated to modify the platforms in compliance with the Third Party recommendations. The American Standard Safety Code for Elevators Dumbwaiters and Escalators (A-17.1) is used as a guide by the Third Party in formulating their recommendations. This code is used because there is no other applicable code for this type of equipment. While the work platforms do not and in some cases can not comply with this code because of operational use, every effort is made to comply with the intent of the code.

  13. Enhancement of safety analysis reliability for a CANDU-6 reactor using RELAP-CANDU/SCAN coupled code system

    International Nuclear Information System (INIS)

    Kim, Man Woong; Choi, Yong Seog; Sin, Chul; Kim, Hyun Koon; Kim, Hho Jung; Hwang, Su Hyun; Hong, In Seob; Kim, Chang Hyo

    2005-01-01

    In LOCA analysis of the CANDU reactor, the system thermal-hydraulic code, RELAP-CANDU, alone cannot predict the transient behavior accurately. Therefore, the best estimate neutronics and system thermal-hydraulic co