Solar-Diesel Hybrid Power System Optimization and Experimental Validation

Science.gov (United States)

Jacobus, Headley Stewart

As of 2008 1.46 billion people, or 22 percent of the World's population, were without electricity. Many of these people live in remote areas where decentralized generation is the only method of electrification. Most mini-grids are powered by diesel generators, but new hybrid power systems are becoming a reliable method to incorporate renewable energy while also reducing total system cost. This thesis quantifies the measurable Operational Costs for an experimental hybrid power system in Sierra Leone. Two software programs, Hybrid2 and HOMER, are used during the system design and subsequent analysis. Experimental data from the installed system is used to validate the two programs and to quantify the savings created by each component within the hybrid system. This thesis bridges the gap between design optimization studies that frequently lack subsequent validation and experimental hybrid system performance studies.

Final Design and Experimental Validation of the Thermal Performance of the LHC Lattice Cryostats

International Nuclear Information System (INIS)

Bourcey, N.; Capatina, O.; Parma, V.; Poncet, A.; Rohmig, P.; Serio, L.; Skoczen, B.; Tock, J.-P.; Williams, L. R.

2004-01-01

The recent commissioning and operation of the LHC String 2 have given a first experimental validation of the global thermal performance of the LHC lattice cryostat at nominal cryogenic conditions. The cryostat designed to minimize the heat inleak from ambient temperature, houses under vacuum and thermally protects the cold mass, which contains the LHC twin-aperture superconducting magnets operating at 1.9 K in superfluid helium. Mechanical components linking the cold mass to the vacuum vessel, such as support posts and insulation vacuum barriers are designed with efficient thermalisations for heat interception to minimise heat conduction. Heat inleak by radiation is reduced by employing multilayer insulation (MLI) wrapped around the cold mass and around an aluminium thermal shield cooled to about 60 K.Measurements of the total helium vaporization rate in String 2 gives, after substraction of supplementary heat loads and end effects, an estimate of the total thermal load to a standard LHC cell (107 m) including two Short Straight Sections and six dipole cryomagnets. Temperature sensors installed at critical locations provide a temperature mapping which allows validation of the calculated and estimated thermal performance of the cryostat components, including efficiency of the heat interceptions

Final Design and Experimental Validation of the Thermal Performance of the LHC Lattice Cryostats

Science.gov (United States)

Bourcey, N.; Capatina, O.; Parma, V.; Poncet, A.; Rohmig, P.; Serio, L.; Skoczen, B.; Tock, J.-P.; Williams, L. R.

2004-06-01

The recent commissioning and operation of the LHC String 2 have given a first experimental validation of the global thermal performance of the LHC lattice cryostat at nominal cryogenic conditions. The cryostat designed to minimize the heat inleak from ambient temperature, houses under vacuum and thermally protects the cold mass, which contains the LHC twin-aperture superconducting magnets operating at 1.9 K in superfluid helium. Mechanical components linking the cold mass to the vacuum vessel, such as support posts and insulation vacuum barriers are designed with efficient thermalisations for heat interception to minimise heat conduction. Heat inleak by radiation is reduced by employing multilayer insulation (MLI) wrapped around the cold mass and around an aluminium thermal shield cooled to about 60 K. Measurements of the total helium vaporization rate in String 2 gives, after substraction of supplementary heat loads and end effects, an estimate of the total thermal load to a standard LHC cell (107 m) including two Short Straight Sections and six dipole cryomagnets. Temperature sensors installed at critical locations provide a temperature mapping which allows validation of the calculated and estimated thermal performance of the cryostat components, including efficiency of the heat interceptions.

Experimental validation of a topology optimized acoustic cavity

DEFF Research Database (Denmark)

Christiansen, Rasmus Ellebæk; Sigmund, Ole; Fernandez Grande, Efren

2015-01-01

This paper presents the experimental validation of an acoustic cavity designed using topology optimization with the goal of minimizing the sound pressure locally for monochromatic excitation. The presented results show good agreement between simulations and measurements. The effect of damping...

Topology Optimization for Wave Propagation Problems with Experimental Validation

DEFF Research Database (Denmark)

Christiansen, Rasmus Ellebæk

designed using the proposed method is provided. A novel approach for designing meta material slabs with selectively tuned negative refractive behavior is outlined. Numerical examples demonstrating the behavior of a slab under different conditions is provided. Results from an experimental studydemonstrating...... agreement with numerical predictions are presented. Finally an approach for designing acoustic wave shaping devices is treated. Three examples of applications are presented, a directional sound emission device, a wave splitting device and a flat focusing lens. Experimental results for the first two devices......This Thesis treats the development and experimental validation of density-based topology optimization methods for wave propagation problems. Problems in the frequency regime where design dimensions are between approximately one fourth and ten wavelengths are considered. All examples treat problems...

Design and experimental validation of Unilateral Linear Halbach magnet arrays for single-sided magnetic resonance.

Science.gov (United States)

Bashyam, Ashvin; Li, Matthew; Cima, Michael J

2018-07-01

Single-sided NMR has the potential for broad utility and has found applications in healthcare, materials analysis, food quality assurance, and the oil and gas industry. These sensors require a remote, strong, uniform magnetic field to perform high sensitivity measurements. We demonstrate a new permanent magnet geometry, the Unilateral Linear Halbach, that combines design principles from "sweet-spot" and linear Halbach magnets to achieve this goal through more efficient use of magnetic flux. We perform sensitivity analysis using numerical simulations to produce a framework for Unilateral Linear Halbach design and assess tradeoffs between design parameters. Additionally, the use of hundreds of small, discrete magnets within the assembly allows for a tunable design, improved robustness to variability in magnetization strength, and increased safety during construction. Experimental validation using a prototype magnet shows close agreement with the simulated magnetic field. The Unilateral Linear Halbach magnet increases the sensitivity, portability, and versatility of single-sided NMR. Copyright © 2018 Elsevier Inc. All rights reserved.

Magnetic Decoupling Design and Experimental Validation of a Radial-Radial Flux Compound-Structure Permanent-Magnet Synchronous Machine for HEVs

Directory of Open Access Journals (Sweden)

Zhiyi Song

2012-10-01

Full Text Available The radial-radial flux compound-structure permanent-magnet synchronous machine (CS-PMSM, integrated by two concentrically arranged permanent-magnet electric machines, is an electromagnetic power-splitting device for hybrid electric vehicles (HEVs. As the two electric machines share a rotor as structural and magnetic common part, their magnetic paths are coupled, leading to possible mutual magnetic-field interference and complex control. In this paper, a design method to ensure magnetic decoupling with minimum yoke thickness of the common rotor is investigated. A prototype machine is designed based on the proposed method, and the feasibility of magnetic decoupling and independent control is validated by experimental tests of mutual influence. The CS-PMSM is tested by a designed driving cycle, and functions to act as starter motor, generator and to help the internal combustion engine (ICE operate at optimum efficiency are validated.

ENGINEERING DESIGN OPTIMIZATION OF HEEL TESTING EQUIPMENT IN THE EXPERIMENTAL VALIDATION OF SAFE WALKING

Directory of Open Access Journals (Sweden)

Cristiano Fragassa

2017-06-01

Full Text Available Experimental test methods for the evaluation of the resistance of heels of ladies' shoes in the case of impact loads are fully defined by International Organization for Standardization (ISO procedures that indicate all the conditions of experiment. A first Standard (ISO 19553 specifies the test method for determining the strength of the heels in the case of single impact. The result offers a valuation of the liability to fail under the sporadic heavy blows. A second Standard (ISO 19556 details a method for testing the capability of heels of women' shoes to survive to the repetition of small impacts provoked by normal walking. These Standards strictly define the features for two different testing devices (with specific materials, geometries, weights, etc. and all the experimental procedures to be followed during tests. On the contrary, this paper describes the technical solutions adopted to design one single experimental device able to perform impact testing of heels in both conditions. Joining the accuracy of mechanic movements with the speed of an electronic control system, a new and flexible equipment for the complete characterization of heels respect to (single or fatigue impacts was developed. Moreover a new level of performances in experimental validation of heel resistance was introduced by the versatility of the user-defined software control programs, able to encode every complex time-depending cycle of impact loads. Dynamic simulations permitted to investigate the impacts on heel in different conditions of testing, optimizing the machine design. The complexity of real stresses on shoes during an ordinary walk and in other common situations (as going up and downstairs was considered for a proper dimensioning.

Status of experimental data for the VHTR core design

Energy Technology Data Exchange (ETDEWEB)

Park, Won Seok; Chang, Jong Hwa; Park, Chang Kue

2004-05-01

The VHTR (Very High Temperature Reactor) is being emerged as a next generation nuclear reactor to demonstrate emission-free nuclear-assisted electricity and hydrogen production. The VHTR could be either a prismatic or pebble type helium cooled, graphite moderated reactor. The final decision will be made after the completion of the pre-conceptual design for each type. For the pre-conceptual design for both types, computational tools are being developed. Experimental data are required to validate the tools to be developed. Many experiments on the HTGR (High Temperature Gas-cooled Reactor) cores have been performed to confirm the design data and to validate the design tools. The applicability and availability of the existing experimental data have been investigated for the VHTR core design in this report.

Validation of a buffet meal design in an experimental restaurant.

Science.gov (United States)

Allirot, Xavier; Saulais, Laure; Disse, Emmanuel; Roth, Hubert; Cazal, Camille; Laville, Martine

2012-06-01

We assessed the reproducibility of intakes and meal mechanics parameters (cumulative energy intake (CEI), number of bites, bite rate, mean energy content per bite) during a buffet meal designed in a natural setting, and their sensitivity to food deprivation. Fourteen men were invited to three lunch sessions in an experimental restaurant. Subjects ate their regular breakfast before sessions A and B. They skipped breakfast before session FAST. The same ad libitum buffet was offered each time. Energy intakes and meal mechanics were assessed by foods weighing and video recording. Intrasubject reproducibility was evaluated by determining intraclass correlation coefficients (ICC). Mixed-models were used to assess the effects of the sessions on CEI. We found a good reproducibility between A and B for total energy (ICC=0.82), carbohydrate (ICC=0.83), lipid (ICC=0.81) and protein intake (ICC=0.79) and for meal mechanics parameters. Total energy, lipid and carbohydrate intake were higher in FAST than in A and B. CEI were found sensitive to differences in hunger level while the other meal mechanics parameters were stable between sessions. In conclusion, a buffet meal in a normal eating environment is a valid tool for assessing the effects of interventions on intakes. Copyright © 2012 Elsevier Ltd. All rights reserved.

Flow cytometry: design, development and experimental validation

International Nuclear Information System (INIS)

Seigneur, Alain

1987-01-01

The flow cytometry techniques allow the analysis and sorting of living biologic cells at rates above five to ten thousand events per second. After a short review, we present in this report the design and development of a 'high-tech' apparatus intended for research laboratories and the experimental results. The first part deals with the physical principles allowing morphologic and functional analysis of cells or cellular components. The measured parameters are as follows: electrical resistance pulse sizing, light scattering and fluorescence. Hydrodynamic centering is used, and in the same way, the division of a water-stream into droplets leading to electrostatic sorting of particles. The second part deals with the apparatus designed by the 'Commissariat a l'Energie Atomique' (C.E.A.) and industrialised by 'ODAM' (ATC 3000). The last part of this thesis work is the performance evaluations of this cyto-meter. The difference between the two size measurement methods are analyzed: electrical resistance pulse sizing versus small-angle light scattering. By an original optics design, high sensitivity has been reached in the fluorescence measurement: the equivalent noise corresponds to six hundred fluorescein isothiocyanate (FITC) molecules. The sorting performances have also been analyzed and the cell viability proven. (author) [fr

Development of the Biological Experimental Design Concept Inventory (BEDCI)

Science.gov (United States)

Deane, Thomas; Nomme, Kathy; Jeffery, Erica; Pollock, Carol; Birol, Gulnur

2014-01-01

Interest in student conception of experimentation inspired the development of a fully validated 14-question inventory on experimental design in biology (BEDCI) by following established best practices in concept inventory (CI) design. This CI can be used to diagnose specific examples of non-expert-like thinking in students and to evaluate the…

Fission Product Experimental Program: Validation and Computational Analysis

Energy Technology Data Exchange (ETDEWEB)

Leclaire, N.; Ivanova, T.; Letang, E. [Inst Radioprotect and Surete Nucl, F-92262 Fontenay Aux Roses (France); Girault, E. [CEA Valduc, Serv Rech Neutron and Critcite, 21 - Is-sur-Tille (France); Thro, J. F. [AREVA NC, F-78000 Versailles (France)

2009-02-15

From 1998 to 2004, a series of critical experiments referred to as the fission product (FP) experimental program was performed at the Commissariat a l'Energie Atomique Valduc research facility. The experiments were designed by Institut de Radioprotection et de Surete Nucleaire (IRSN) and funded by AREVA NC and IRSN within the French program supporting development of a technical basis for burnup credit validation. The experiments were performed with the following six key fission products encountered in solution either individually or as mixtures: {sup 103}Rh, {sup 133}Cs, {sup nat}Nd, {sup 149}Sm, {sup 152}Sm, and {sup 155}Gd. The program aimed at compensating for the lack of information on critical experiments involving FPs and at establishing a basis for FPs credit validation. One hundred forty-five critical experiments were performed, evaluated, and analyzed with the French CRISTAL criticality safety package and the American SCALE5. 1 code system employing different cross-section libraries. The aim of the paper is to show the experimental data potential to improve the ability to perform validation of full burnup credit calculation. The paper describes three Phases of the experimental program; the results of preliminary evaluation, the calculation, and the sensitivity/uncertainty study of the FP experiments used to validate the APOLLO2-MORET 4 route in the CRISTAL criticality package for burnup credit applications. (authors)

Experimental and numerical validation of a two-region-designed pebble bed reactor with dynamic core

International Nuclear Information System (INIS)

Jiang, S.Y.; Yang, X.T.; Tang, Z.W.; Wang, W.J.; Tu, J.Y.; Liu, Z.Y.; Li, J.

2012-01-01

Highlights: ► The experimental installation has been built to investigate the pebble flow. ► The feasibility of two-region pebble bed reactor has been verified. ► The pebble flow is more uniform in a taller vessel than that in a lower vessel. ► Larger base cone angle will decrease the scale of the stagnant zone. - Abstract: The pebble flow is the principal issue for the design of the pebble bed reactor. In order to verify the feasibility of a two-region-designed pebble bed reactor, the experimental installation with a taller vessel has been built, which is proportional to the real pebble bed reactor. With the aid of the experimental installation, the stable establishment and maintenance of the two-region arrangement has been verified, at the same time, the applicability of the DEM program has been also validated. Research results show: (1) The pebble's bouncing on the free surface is an important factor for the mixing of the different colored pebbles. (2) Through the guide plates installed in the top of the pebble packing, the size of the mixing zone can be reduced from 6–7 times to 3–4 times the pebble diameter. (3) The relationship between the width of the central region and the ratio of loading pebbles is approximately linear in the taller vessel. (4) The heighten part of the pebble packing can improve the uniformity of the flowing in the lower. (5) To increase the base cone angle can decrease the scale of the stagnant zone. All of these conclusions are meaningful to the design of the real pebble reactor.

Preliminary Validation of the MATRA-LMR Code Using Existing Sodium-Cooled Experimental Data

International Nuclear Information System (INIS)

Choi, Sun Rock; Kim, Sangji

2014-01-01

The main objective of the SFR prototype plant is to verify TRU metal fuel performance, reactor operation, and transmutation ability of high-level wastes. The core thermal-hydraulic design is used to ensure the safe fuel performance during the whole plant operation. The fuel design limit is highly dependent on both the maximum cladding temperature and the uncertainties of the design parameters. Therefore, an accurate temperature calculation in each subassembly is highly important to assure a safe and reliable operation of the reactor systems. The current core thermalhydraulic design is mainly performed using the SLTHEN (Steady-State LMR Thermal-Hydraulic Analysis Code Based on ENERGY Model) code, which has been already validated using the existing sodium-cooled experimental data. In addition to the SLTHEN code, a detailed analysis is performed using the MATRA-LMR (Multichannel Analyzer for Transient and steady-state in Rod Array-Liquid Metal Reactor) code. In this work, the MATRA-LMR code is validated for a single subassembly evaluation using the previous experimental data. The MATRA-LMR code has been validated using existing sodium-cooled experimental data. The results demonstrate that the design code appropriately predicts the temperature distributions compared with the experimental values. Major differences are observed in the experiments with the large pin number due to the radial-wise mixing difference

PEMFC modeling and experimental validation

Energy Technology Data Exchange (ETDEWEB)

Vargas, J.V.C. [Federal University of Parana (UFPR), Curitiba, PR (Brazil). Dept. of Mechanical Engineering], E-mail: jvargas@demec.ufpr.br; Ordonez, J.C.; Martins, L.S. [Florida State University, Tallahassee, FL (United States). Center for Advanced Power Systems], Emails: ordonez@caps.fsu.edu, martins@caps.fsu.edu

2009-07-01

In this paper, a simplified and comprehensive PEMFC mathematical model introduced in previous studies is experimentally validated. Numerical results are obtained for an existing set of commercial unit PEM fuel cells. The model accounts for pressure drops in the gas channels, and for temperature gradients with respect to space in the flow direction, that are investigated by direct infrared imaging, showing that even at low current operation such gradients are present in fuel cell operation, and therefore should be considered by a PEMFC model, since large coolant flow rates are limited due to induced high pressure drops in the cooling channels. The computed polarization and power curves are directly compared to the experimentally measured ones with good qualitative and quantitative agreement. The combination of accuracy and low computational time allow for the future utilization of the model as a reliable tool for PEMFC simulation, control, design and optimization purposes. (author)

Selecting and Improving Quasi-Experimental Designs in Effectiveness and Implementation Research.

Science.gov (United States)

Handley, Margaret A; Lyles, Courtney R; McCulloch, Charles; Cattamanchi, Adithya

2018-04-01

Interventional researchers face many design challenges when assessing intervention implementation in real-world settings. Intervention implementation requires holding fast on internal validity needs while incorporating external validity considerations (such as uptake by diverse subpopulations, acceptability, cost, and sustainability). Quasi-experimental designs (QEDs) are increasingly employed to achieve a balance between internal and external validity. Although these designs are often referred to and summarized in terms of logistical benefits, there is still uncertainty about (a) selecting from among various QEDs and (b) developing strategies to strengthen the internal and external validity of QEDs. We focus here on commonly used QEDs (prepost designs with nonequivalent control groups, interrupted time series, and stepped-wedge designs) and discuss several variants that maximize internal and external validity at the design, execution and implementation, and analysis stages.

Development and Experimental Validation of a TRNSYS Dynamic Tool for Design and Energy Optimization of Ground Source Heat Pump Systems

Directory of Open Access Journals (Sweden)

Félix Ruiz-Calvo

2017-09-01

Full Text Available Ground source heat pump (GSHP systems stand for an efficient technology for renewable heating and cooling in buildings. To optimize not only the design but also the operation of the system, a complete dynamic model becomes a highly useful tool, since it allows testing any design modifications and different optimization strategies without actually implementing them at the experimental facility. Usually, this type of systems presents strong dynamic operating conditions. Therefore, the model should be able to predict not only the steady-state behavior of the system but also the short-term response. This paper presents a complete GSHP system model based on an experimental facility, located at Universitat Politècnica de València. The installation was constructed in the framework of a European collaborative project with title GeoCool. The model, developed in TRNSYS, has been validated against experimental data, and it accurately predicts both the short- and long-term behavior of the system.

Design of Passive Acoustic Wave Shaping Devices and Their Experimental Validation

DEFF Research Database (Denmark)

Christiansen, Rasmus Ellebæk; Sigmund, Ole; Fernandez Grande, Efren

We discuss a topology optimization based approach for designing passive acoustic wave shaping devices and demonstrate its application to; directional sound emission [1], sound focusing and wave splitting. Optimized devices, numerical and experimental results are presented and benchmarked against...... other designs proposed in the literature. We focus on design problems where the size of the device is on the order of the wavelength, a problematic region for traditional design methods, such as ray tracing.The acoustic optimization problem is formulated in the frequency domain and modeled...

Design and experimental validation of the inlet guide vane system of a mini hydraulic bulb-turbine

Energy Technology Data Exchange (ETDEWEB)

Ferro, L.M.C. [Department of Mechanical Engineering, Escola Superior de Tecnologia de Setubal, Polytechnic Institute of Setubal, Campus do IPS, Estefanilha, 2910-761 Setubal (Portugal); IDMEC, Instituto Superior Tecnico, Technical University of Lisbon, Av. Rovisco Pais,1049-001 Lisboa (Portugal); Gato, L.M.C.; Falcao, A.F.O. [IDMEC, Instituto Superior Tecnico, Technical University of Lisbon, Av. Rovisco Pais,1049-001 Lisboa (Portugal)

2010-09-15

The paper presents a fast design method for the inlet guide vanes of low-cost mini hydraulic bulb turbines. The guide vanes are positioned between two conical surfaces with a common vertex and have constant thickness distribution, except close to the leading and the trailing edges. The conical-walled inlet guide vane row is designed using a quasi-three-dimensional calculation method, by prescribing the angular-momentum distribution along the span at the outlet section of the guide vanes. The meridional through-flow is computed by a streamline curvature method and the blade-to-blade flow by a singularity surface method. The stagger angle and the vane camber are computed to fulfil the required design circulation and zero-incidence flow at the leading edge. The final vane shape is a single-curvature surface with straight leading and trailing edges. To validate the design method, a conical-walled inlet guide vane row nozzle-model with six fixed vanes was designed, manufactured and tested in an airflow rig. Traversing measurements along the circumferential and radial directions were made with a five-hole probe. The experimental results are compared with the prescribed design conditions and with numerical results from the three-dimensional inviscid and viscous flow computed with the FLUENT code. (author)

INL Experimental Program Roadmap for Thermal Hydraulic Code Validation

Energy Technology Data Exchange (ETDEWEB)

Glenn McCreery; Hugh McIlroy

2007-09-01

Advanced computer modeling and simulation tools and protocols will be heavily relied on for a wide variety of system studies, engineering design activities, and other aspects of the Next Generation Nuclear Power (NGNP) Very High Temperature Reactor (VHTR), the DOE Global Nuclear Energy Partnership (GNEP), and light-water reactors. The goal is for all modeling and simulation tools to be demonstrated accurate and reliable through a formal Verification and Validation (V&V) process, especially where such tools are to be used to establish safety margins and support regulatory compliance, or to design a system in a manner that reduces the role of expensive mockups and prototypes. Recent literature identifies specific experimental principles that must be followed in order to insure that experimental data meet the standards required for a “benchmark” database. Even for well conducted experiments, missing experimental details, such as geometrical definition, data reduction procedures, and manufacturing tolerances have led to poor Benchmark calculations. The INL has a long and deep history of research in thermal hydraulics, especially in the 1960s through 1980s when many programs such as LOFT and Semiscle were devoted to light-water reactor safety research, the EBRII fast reactor was in operation, and a strong geothermal energy program was established. The past can serve as a partial guide for reinvigorating thermal hydraulic research at the laboratory. However, new research programs need to fully incorporate modern experimental methods such as measurement techniques using the latest instrumentation, computerized data reduction, and scaling methodology. The path forward for establishing experimental research for code model validation will require benchmark experiments conducted in suitable facilities located at the INL. This document describes thermal hydraulic facility requirements and candidate buildings and presents examples of suitable validation experiments related

Deployable and Conformal Planar Micro-Devices: Design and Model Validation

Directory of Open Access Journals (Sweden)

Jinda Zhuang

2014-08-01

Full Text Available We report a design concept for a deployable planar microdevice and the modeling and experimental validation of its mechanical behavior. The device consists of foldable membranes that are suspended between flexible stems and actuated by push-pull wires. Such a deployable device can be introduced into a region of interest in its compact “collapsed” state and then deployed to conformally cover a large two-dimensional surface area for minimally invasive biomedical operations and other engineering applications. We develop and experimentally validate theoretical models based on the energy minimization approach to examine the conformality and figures of merit of the device. The experimental results obtained using model contact surfaces agree well with the prediction and quantitatively highlight the importance of the membrane bending modulus in controlling surface conformality. The present study establishes an early foundation for the mechanical design of this and related deployable planar microdevice concepts.

Integrated Design Validation: Combining Simulation and Formal Verification for Digital Integrated Circuits

Directory of Open Access Journals (Sweden)

Lun Li

2006-04-01

Full Text Available The correct design of complex hardware continues to challenge engineers. Bugs in a design that are not uncovered in early design stages can be extremely expensive. Simulation is a predominantly used tool to validate a design in industry. Formal verification overcomes the weakness of exhaustive simulation by applying mathematical methodologies to validate a design. The work described here focuses upon a technique that integrates the best characteristics of both simulation and formal verification methods to provide an effective design validation tool, referred as Integrated Design Validation (IDV. The novelty in this approach consists of three components, circuit complexity analysis, partitioning based on design hierarchy, and coverage analysis. The circuit complexity analyzer and partitioning decompose a large design into sub-components and feed sub-components to different verification and/or simulation tools based upon known existing strengths of modern verification and simulation tools. The coverage analysis unit computes the coverage of design validation and improves the coverage by further partitioning. Various simulation and verification tools comprising IDV are evaluated and an example is used to illustrate the overall validation process. The overall process successfully validates the example to a high coverage rate within a short time. The experimental result shows that our approach is a very promising design validation method.

Application of a computational situation assessment model to human system interface design and experimental validation of its effectiveness

International Nuclear Information System (INIS)

Lee, Hyun-Chul; Koh, Kwang-Yong; Seong, Poong-Hyun

2013-01-01

Highlights: ► We validate the effectiveness of a proposed procedure thru an experiment. ► The proposed procedure addresses the salient coding of the key information. ► It was found that salience coding affects operators’ attention significantly. ► The first observation to the key information quickly guided to the correct situation awareness. ► It was validated the proposed procedure is effective for better situation awareness. - Abstract: To evaluate the effects of human cognitive characteristics on situation awareness, a computational situation assessment model of nuclear power plant operators has been developed, as well as a procedure to apply the developed model to the design of human system interfaces (HSIs). The concept of the proposed procedure is to identify the key information source, which is expected to guarantee fast and accurate diagnosis when operators attend to it. The developed computational model is used to search the diagnostic paths and the key information source. In this study, an experiment with twelve trained participants was executed to validate the effectiveness of the proposed procedure. Eighteen scenarios covering various accidents were administered twice for each subject, and experimental data were collected and analyzed. As a result of the data analysis, it was validated that the salience level of information sources significantly influences the attention of operators, and the first observation of the key information sources leads operators to a quick and correct situation assessment. Therefore, we conclude that the proposed procedure for applying the developed model to HSI design is effective

Optimal Experimental Design for Large-Scale Bayesian Inverse Problems

KAUST Repository

Ghattas, Omar

2014-01-06

We develop a Bayesian framework for the optimal experimental design of the shock tube experiments which are being carried out at the KAUST Clean Combustion Research Center. The unknown parameters are the pre-exponential parameters and the activation energies in the reaction rate expressions. The control parameters are the initial mixture composition and the temperature. The approach is based on first building a polynomial based surrogate model for the observables relevant to the shock tube experiments. Based on these surrogates, a novel MAP based approach is used to estimate the expected information gain in the proposed experiments, and to select the best experimental set-ups yielding the optimal expected information gains. The validity of the approach is tested using synthetic data generated by sampling the PC surrogate. We finally outline a methodology for validation using actual laboratory experiments, and extending experimental design methodology to the cases where the control parameters are noisy.

HTC Experimental Program: Validation and Calculational Analysis

Energy Technology Data Exchange (ETDEWEB)

Fernex, F.; Ivanova, T.; Bernard, F.; Letang, E. [Inst Radioprotect and Surete Nucl, F-92262 Fontenay Aux Roses (France); Fouillaud, P. [CEA Valduc, Serv Rech Neutron and Critcite, 21 - Is-sur-Tille (France); Thro, J. F. [AREVA NC, F-78000 Versailles (France)

2009-05-15

In the 1980's a series of the Haut Taux de Combustion (HTC) critical experiments with fuel pins in a water-moderated lattice was conducted at the Apparatus B experimental facility in Valduc (Commissariat a I'Energie Atomique, France) with the support of the Institut de Radioprotection et de Surete Nucleaire and AREVA NC. Four series of experiments were designed to assess profit associated with actinide-only burnup credit in the criticality safety evaluation for fuel handling, pool storage, and spent-fuel cask conditions. The HTC rods, specifically fabricated for the experiments, simulated typical pressurized water reactor uranium oxide spent fuel that had an initial enrichment of 4. 5 wt% {sup 235}U and was burned to 37.5 GWd/tonne U. The configurations have been modeled with the CRISTAL criticality package and SCALE 5.1 code system. Sensitivity/uncertainty analysis has been employed to evaluate the HTC experiments and to study their applicability for validation of burnup credit calculations. This paper presents the experimental program, the principal results of the experiment evaluation, and modeling. The HTC data applicability to burnup credit validation is demonstrated with an example of spent-fuel storage models. (authors)

Development of a quality-assessment tool for experimental bruxism studies: reliability and validity.

Science.gov (United States)

Dawson, Andreas; Raphael, Karen G; Glaros, Alan; Axelsson, Susanna; Arima, Taro; Ernberg, Malin; Farella, Mauro; Lobbezoo, Frank; Manfredini, Daniele; Michelotti, Ambra; Svensson, Peter; List, Thomas

2013-01-01

To combine empirical evidence and expert opinion in a formal consensus method in order to develop a quality-assessment tool for experimental bruxism studies in systematic reviews. Tool development comprised five steps: (1) preliminary decisions, (2) item generation, (3) face-validity assessment, (4) reliability and discriminitive validity assessment, and (5) instrument refinement. The kappa value and phi-coefficient were calculated to assess inter-observer reliability and discriminative ability, respectively. Following preliminary decisions and a literature review, a list of 52 items to be considered for inclusion in the tool was compiled. Eleven experts were invited to join a Delphi panel and 10 accepted. Four Delphi rounds reduced the preliminary tool-Quality-Assessment Tool for Experimental Bruxism Studies (Qu-ATEBS)- to 8 items: study aim, study sample, control condition or group, study design, experimental bruxism task, statistics, interpretation of results, and conflict of interest statement. Consensus among the Delphi panelists yielded good face validity. Inter-observer reliability was acceptable (k = 0.77). Discriminative validity was excellent (phi coefficient 1.0; P reviews of experimental bruxism studies, exhibits face validity, excellent discriminative validity, and acceptable inter-observer reliability. Development of quality assessment tools for many other topics in the orofacial pain literature is needed and may follow the described procedure.

Quasi-experimental study designs series-paper 7: assessing the assumptions.

Science.gov (United States)

Bärnighausen, Till; Oldenburg, Catherine; Tugwell, Peter; Bommer, Christian; Ebert, Cara; Barreto, Mauricio; Djimeu, Eric; Haber, Noah; Waddington, Hugh; Rockers, Peter; Sianesi, Barbara; Bor, Jacob; Fink, Günther; Valentine, Jeffrey; Tanner, Jeffrey; Stanley, Tom; Sierra, Eduardo; Tchetgen, Eric Tchetgen; Atun, Rifat; Vollmer, Sebastian

2017-09-01

Quasi-experimental designs are gaining popularity in epidemiology and health systems research-in particular for the evaluation of health care practice, programs, and policy-because they allow strong causal inferences without randomized controlled experiments. We describe the concepts underlying five important quasi-experimental designs: Instrumental Variables, Regression Discontinuity, Interrupted Time Series, Fixed Effects, and Difference-in-Differences designs. We illustrate each of the designs with an example from health research. We then describe the assumptions required for each of the designs to ensure valid causal inference and discuss the tests available to examine the assumptions. Copyright © 2017 Elsevier Inc. All rights reserved.

Modelling and experimental validation for off-design performance of the helical heat exchanger with LMTD correction taken into account

Energy Technology Data Exchange (ETDEWEB)

Phu, Nguyen Minh; Trinh, Nguyen Thi Minh [Vietnam National University, Ho Chi Minh City (Viet Nam)

2016-07-15

Today the helical coil heat exchanger is being employed widely due to its dominant advantages. In this study, a mathematical model was established to predict off-design works of the helical heat exchanger. The model was based on the LMTD and e-NTU methods, where a LMTD correction factor was taken into account to increase accuracy. An experimental apparatus was set-up to validate the model. Results showed that errors of thermal duty, outlet hot fluid temperature, outlet cold fluid temperature, shell-side pressure drop, and tube-side pressure drop were respectively +-5%, +-1%, +-1%, +-5% and +-2%. Diagrams of dimensionless operating parameters and a regression function were also presented as design-maps, a fast calculator for usage in design and operation of the exchanger. The study is expected to be a good tool to estimate off-design conditions of the single-phase helical heat exchangers.

Analytical and Experimental Study for Validation of the Device to Confine BN Reactor Melted Fuel

International Nuclear Information System (INIS)

Rogozhkin, S.; Osipov, S.; Sobolev, V.; Shepelev, S.; Kozhaev, A.; Mavrin, M.; Ryabov, A.

2013-01-01

To validate the design and confirm the design characteristics of the special retaining device (core catcher) used for protection of BN reactor vessel in the case of a severe beyond-design basis accident with core melting, computational and experimental studies were carried out. The Tray test facility that uses water as coolant was developed and fabricated by OKBM; experimental studies were performed. To verify the methodical approach used for the computational study, experimental results obtained in the Tray test facility were compared with numerical simulation results obtained by the STAR-CCM+ CFD code

Development and Validation of LC Method for the Determination of Famciclovir in Pharmaceutical Formulation Using an Experimental Design

Directory of Open Access Journals (Sweden)

Srinivas Vishnumulaka

2008-01-01

Full Text Available A rapid and sensitive RP-HPLC method with UV detection (242 nm for routine analysis of famciclovir in pharmaceutical formulations was developed. Chromatography was performed with mobile phase containing a mixture of methanol and phosphate buffer (50:50, v/v with flow rate 1.0 mL min−1. Quantitation was accomplished with internal standard method. The procedure was validated for linearity (correlation coefficient =0.9999, accuracy, robustness and intermediate precision. Experimental design was used for validation of robustness and intermediate precision. To test robustness, three factors were considered; percentage v/v of methanol in mobile phase, flow rate and pH; flow rate, the percentage of organic modifier and pH have considerable important effect on the response. For intermediate precision measure the variables considered were: analyst, equipment and number of days. The RSD value (0.86%, n=24 indicated an acceptable precision of the analytical method. The proposed method was simple, sensitive, precise, accurate and quick and useful for routine quality control.

Optimization of instrumental neutron activation analysis method by means of 2k experimental design technique aiming the validation of analytical procedures

International Nuclear Information System (INIS)

Petroni, Robson; Moreira, Edson G.

2013-01-01

In this study optimization of procedures and standardization of Instrumental Neutron Activation Analysis (INAA) methods were carried out for the determination of the elements arsenic, chromium, cobalt, iron, rubidium, scandium, selenium and zinc in biological materials. The aim is to validate the analytical methods for future accreditation at the National Institute of Metrology, Quality and Technology (INMETRO). The 2 k experimental design was applied for evaluation of the individual contribution of selected variables of the analytical procedure in the final mass fraction result. Samples of Mussel Tissue Certified Reference Material and multi-element standards were analyzed considering the following variables: sample decay time, counting time and sample distance to detector. The standard multi-element concentration (comparator standard), mass of the sample and irradiation time were maintained constant in this procedure. By means of the statistical analysis and theoretical and experimental considerations it was determined the optimized experimental conditions for the analytical methods that will be adopted for the validation procedure of INAA methods in the Neutron Activation Analysis Laboratory (LAN) of the Research Reactor Center (CRPq) at the Nuclear and Energy Research Institute (IPEN - CNEN/SP). Optimized conditions were estimated based on the results of z-score tests, main effect and interaction effects. The results obtained with the different experimental configurations were evaluated for accuracy (precision and trueness) for each measurement. (author)

Spatiotemporally Representative and Cost-Efficient Sampling Design for Validation Activities in Wanglang Experimental Site

Directory of Open Access Journals (Sweden)

Gaofei Yin

2017-11-01

Full Text Available Spatiotemporally representative Elementary Sampling Units (ESUs are required for capturing the temporal variations in surface spatial heterogeneity through field measurements. Since inaccessibility often coexists with heterogeneity, a cost-efficient sampling design is mandatory. We proposed a sampling strategy to generate spatiotemporally representative and cost-efficient ESUs based on the conditioned Latin hypercube sampling scheme. The proposed strategy was constrained by multi-temporal Normalized Difference Vegetation Index (NDVI imagery, and the ESUs were limited within a sampling feasible region established based on accessibility criteria. A novel criterion based on the Overlapping Area (OA between the NDVI frequency distribution histogram from the sampled ESUs and that from the entire study area was used to assess the sampling efficiency. A case study in Wanglang National Nature Reserve in China showed that the proposed strategy improves the spatiotemporally representativeness of sampling (mean annual OA = 74.7% compared to the single-temporally constrained (OA = 68.7% and the random sampling (OA = 63.1% strategies. The introduction of the feasible region constraint significantly reduces in-situ labour-intensive characterization necessities at expenses of about 9% loss in the spatiotemporal representativeness of the sampling. Our study will support the validation activities in Wanglang experimental site providing a benchmark for locating the nodes of automatic observation systems (e.g., LAINet which need a spatially distributed and temporally fixed sampling design.

Experimental validation for calcul methods of structures having shock non-linearity

International Nuclear Information System (INIS)

Brochard, D.; Buland, P.

1987-01-01

For the seismic analysis of non-linear structures, numerical methods have been developed which need to be validated on experimental results. The aim of this paper is to present the design method of a test program which results will be used for this purpose. Some applications to nuclear components will illustrate this presentation [fr

Experimental validation of solid rocket motor damping models

Science.gov (United States)

Riso, Cristina; Fransen, Sebastiaan; Mastroddi, Franco; Coppotelli, Giuliano; Trequattrini, Francesco; De Vivo, Alessio

2017-12-01

In design and certification of spacecraft, payload/launcher coupled load analyses are performed to simulate the satellite dynamic environment. To obtain accurate predictions, the system damping properties must be properly taken into account in the finite element model used for coupled load analysis. This is typically done using a structural damping characterization in the frequency domain, which is not applicable in the time domain. Therefore, the structural damping matrix of the system must be converted into an equivalent viscous damping matrix when a transient coupled load analysis is performed. This paper focuses on the validation of equivalent viscous damping methods for dynamically condensed finite element models via correlation with experimental data for a realistic structure representative of a slender launch vehicle with solid rocket motors. A second scope of the paper is to investigate how to conveniently choose a single combination of Young's modulus and structural damping coefficient—complex Young's modulus—to approximate the viscoelastic behavior of a solid propellant material in the frequency band of interest for coupled load analysis. A scaled-down test article inspired to the Z9-ignition Vega launcher configuration is designed, manufactured, and experimentally tested to obtain data for validation of the equivalent viscous damping methods. The Z9-like component of the test article is filled with a viscoelastic material representative of the Z9 solid propellant that is also preliminarily tested to investigate the dependency of the complex Young's modulus on the excitation frequency and provide data for the test article finite element model. Experimental results from seismic and shock tests performed on the test configuration are correlated with numerical results from frequency and time domain analyses carried out on its dynamically condensed finite element model to assess the applicability of different equivalent viscous damping methods to describe

Experimental validation of solid rocket motor damping models

Science.gov (United States)

Riso, Cristina; Fransen, Sebastiaan; Mastroddi, Franco; Coppotelli, Giuliano; Trequattrini, Francesco; De Vivo, Alessio

2018-06-01

In design and certification of spacecraft, payload/launcher coupled load analyses are performed to simulate the satellite dynamic environment. To obtain accurate predictions, the system damping properties must be properly taken into account in the finite element model used for coupled load analysis. This is typically done using a structural damping characterization in the frequency domain, which is not applicable in the time domain. Therefore, the structural damping matrix of the system must be converted into an equivalent viscous damping matrix when a transient coupled load analysis is performed. This paper focuses on the validation of equivalent viscous damping methods for dynamically condensed finite element models via correlation with experimental data for a realistic structure representative of a slender launch vehicle with solid rocket motors. A second scope of the paper is to investigate how to conveniently choose a single combination of Young's modulus and structural damping coefficient—complex Young's modulus—to approximate the viscoelastic behavior of a solid propellant material in the frequency band of interest for coupled load analysis. A scaled-down test article inspired to the Z9-ignition Vega launcher configuration is designed, manufactured, and experimentally tested to obtain data for validation of the equivalent viscous damping methods. The Z9-like component of the test article is filled with a viscoelastic material representative of the Z9 solid propellant that is also preliminarily tested to investigate the dependency of the complex Young's modulus on the excitation frequency and provide data for the test article finite element model. Experimental results from seismic and shock tests performed on the test configuration are correlated with numerical results from frequency and time domain analyses carried out on its dynamically condensed finite element model to assess the applicability of different equivalent viscous damping methods to describe

Experimental validation of prototype high voltage bushing

Science.gov (United States)

Shah, Sejal; Tyagi, H.; Sharma, D.; Parmar, D.; M. N., Vishnudev; Joshi, K.; Patel, K.; Yadav, A.; Patel, R.; Bandyopadhyay, M.; Rotti, C.; Chakraborty, A.

2017-08-01

Prototype High voltage bushing (PHVB) is a scaled down configuration of DNB High Voltage Bushing (HVB) of ITER. It is designed for operation at 50 kV DC to ensure operational performance and thereby confirming the design configuration of DNB HVB. Two concentric insulators viz. Ceramic and Fiber reinforced polymer (FRP) rings are used as double layered vacuum boundary for 50 kV isolation between grounded and high voltage flanges. Stress shields are designed for smooth electric field distribution. During ceramic to Kovar brazing, spilling cannot be controlled which may lead to high localized electrostatic stress. To understand spilling phenomenon and precise stress calculation, quantitative analysis was performed using Scanning Electron Microscopy (SEM) of brazed sample and similar configuration modeled while performing the Finite Element (FE) analysis. FE analysis of PHVB is performed to find out electrical stresses on different areas of PHVB and are maintained similar to DNB HV Bushing. With this configuration, the experiment is performed considering ITER like vacuum and electrical parameters. Initial HV test is performed by temporary vacuum sealing arrangements using gaskets/O-rings at both ends in order to achieve desired vacuum and keep the system maintainable. During validation test, 50 kV voltage withstand is performed for one hour. Voltage withstand test for 60 kV DC (20% higher rated voltage) have also been performed without any breakdown. Successful operation of PHVB confirms the design of DNB HV Bushing. In this paper, configuration of PHVB with experimental validation data is presented.

Experimental validation of a numerical 3-D finite model applied to wind turbines design under vibration constraints: TREVISE platform

Science.gov (United States)

Sellami, Takwa; Jelassi, Sana; Darcherif, Abdel Moumen; Berriri, Hanen; Mimouni, Med Faouzi

2018-04-01

With the advancement of wind turbines towards complex structures, the requirement of trusty structural models has become more apparent. Hence, the vibration characteristics of the wind turbine components, like the blades and the tower, have to be extracted under vibration constraints. Although extracting the modal properties of blades is a simple task, calculating precise modal data for the whole wind turbine coupled to its tower/foundation is still a perplexing task. In this framework, this paper focuses on the investigation of the structural modeling approach of modern commercial micro-turbines. Thus, the structural model a complex designed wind turbine, which is Rutland 504, is established based on both experimental and numerical methods. A three-dimensional (3-D) numerical model of the structure was set up based on the finite volume method (FVM) using the academic finite element analysis software ANSYS. To validate the created model, experimental vibration tests were carried out using the vibration test system of TREVISE platform at ECAM-EPMI. The tests were based on the experimental modal analysis (EMA) technique, which is one of the most efficient techniques for identifying structures parameters. Indeed, the poles and residues of the frequency response functions (FRF), between input and output spectra, were calculated to extract the mode shapes and the natural frequencies of the structure. Based on the obtained modal parameters, the numerical designed model was up-dated.

A Comprehensive Validation Methodology for Sparse Experimental Data

Science.gov (United States)

Norman, Ryan B.; Blattnig, Steve R.

2010-01-01

A comprehensive program of verification and validation has been undertaken to assess the applicability of models to space radiation shielding applications and to track progress as models are developed over time. The models are placed under configuration control, and automated validation tests are used so that comparisons can readily be made as models are improved. Though direct comparisons between theoretical results and experimental data are desired for validation purposes, such comparisons are not always possible due to lack of data. In this work, two uncertainty metrics are introduced that are suitable for validating theoretical models against sparse experimental databases. The nuclear physics models, NUCFRG2 and QMSFRG, are compared to an experimental database consisting of over 3600 experimental cross sections to demonstrate the applicability of the metrics. A cumulative uncertainty metric is applied to the question of overall model accuracy, while a metric based on the median uncertainty is used to analyze the models from the perspective of model development by analyzing subsets of the model parameter space.

Chemical looping reforming in packed-bed reactors : modelling, experimental validation and large-scale reactor design

NARCIS (Netherlands)

Spallina, V.; Marinello, B.; Gallucci, F.; Romano, M.C.; van Sint Annaland, M.

This paper addresses the experimental demonstration and model validation of chemical looping reforming in dynamically operated packed-bed reactors for the production of H2 or CH3OH with integrated CO2 capture. This process is a combination of auto-thermal and steam methane reforming and is carried

Optimization of instrumental neutron activation analysis method by means of 2{sup k} experimental design technique aiming the validation of analytical procedures

Energy Technology Data Exchange (ETDEWEB)

Petroni, Robson; Moreira, Edson G., E-mail: rpetroni@ipen.br, E-mail: emoreira@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2013-07-01

In this study optimization of procedures and standardization of Instrumental Neutron Activation Analysis (INAA) methods were carried out for the determination of the elements arsenic, chromium, cobalt, iron, rubidium, scandium, selenium and zinc in biological materials. The aim is to validate the analytical methods for future accreditation at the National Institute of Metrology, Quality and Technology (INMETRO). The 2{sup k} experimental design was applied for evaluation of the individual contribution of selected variables of the analytical procedure in the final mass fraction result. Samples of Mussel Tissue Certified Reference Material and multi-element standards were analyzed considering the following variables: sample decay time, counting time and sample distance to detector. The standard multi-element concentration (comparator standard), mass of the sample and irradiation time were maintained constant in this procedure. By means of the statistical analysis and theoretical and experimental considerations it was determined the optimized experimental conditions for the analytical methods that will be adopted for the validation procedure of INAA methods in the Neutron Activation Analysis Laboratory (LAN) of the Research Reactor Center (CRPq) at the Nuclear and Energy Research Institute (IPEN - CNEN/SP). Optimized conditions were estimated based on the results of z-score tests, main effect and interaction effects. The results obtained with the different experimental configurations were evaluated for accuracy (precision and trueness) for each measurement. (author)

The TALL-3D facility design and commissioning tests for validation of coupled STH and CFD codes

Energy Technology Data Exchange (ETDEWEB)

Grishchenko, Dmitry, E-mail: dmitry@safety.sci.kth.se; Jeltsov, Marti, E-mail: marti@safety.sci.kth.se; Kööp, Kaspar, E-mail: kaspar@safety.sci.kth.se; Karbojian, Aram, E-mail: karbojan@kth.se; Villanueva, Walter, E-mail: walter@safety.sci.kth.se; Kudinov, Pavel, E-mail: pavel@safety.sci.kth.se

2015-08-15

Highlights: • Design of a heavy liquid thermal-hydraulic loop for CFD/STH code validation. • Description of the loop instrumentation and assessment of measurement error. • Experimental data from forced to natural circulation transient. - Abstract: Application of coupled CFD (Computational Fluid Dynamics) and STH (System Thermal Hydraulics) codes is a prerequisite for computationally affordable and sufficiently accurate prediction of thermal-hydraulics of complex systems. Coupled STH and CFD codes require validation for understanding and quantification of the sources of uncertainties in the code prediction. TALL-3D is a liquid Lead Bismuth Eutectic (LBE) loop developed according to the requirements for the experimental data for validation of coupled STH and CFD codes. The goals of the facility design are to provide (i) mutual feedback between natural circulation in the loop and complex 3D mixing and stratification phenomena in the pool-type test section, (ii) a possibility to validate standalone STH and CFD codes for each subsection of the facility, and (iii) sufficient number of experimental data to separate the process of input model calibration and code validation. Description of the facility design and its main components, approach to estimation of experimental uncertainty and calibration of model input parameters that are not directly measured in the experiment are discussed in the paper. First experimental data from the forced to natural circulation transient is also provided in the paper.

CFD Modeling and Experimental Validation of a Solar Still

Directory of Open Access Journals (Sweden)

Mahmood Tahir

2017-01-01

Full Text Available Earth is the densest planet of the solar system with total area of 510.072 million square Km. Over 71.68% of this area is covered with water leaving a scant area of 28.32% for human to inhabit. The fresh water accounts for only 2.5% of the total volume and the rest is the brackish water. Presently, the world is facing chief problem of lack of potable water. This issue can be addressed by converting brackish water into potable through a solar distillation process and solar still is specially assigned for this purpose. Efficiency of a solar still explicitly depends on its design parameters, such as wall material, chamber depth, width and slope of the zcondensing surface. This study was aimed at investigating the solar still parameters using CFD modeling and experimental validation. The simulation data of ANSYS-FLUENT was compared with actual experimental data. A close agreement among the simulated and experimental results was seen in the presented work. It reveals that ANSYS-FLUENT is a potent tool to analyse the efficiency of the new designs of the solar distillation systems.

Three-dimensional shape optimization of a cemented hip stem and experimental validations.

Science.gov (United States)

Higa, Masaru; Tanino, Hiromasa; Nishimura, Ikuya; Mitamura, Yoshinori; Matsuno, Takeo; Ito, Hiroshi

2015-03-01

This study proposes novel optimized stem geometry with low stress values in the cement using a finite element (FE) analysis combined with an optimization procedure and experimental measurements of cement stress in vitro. We first optimized an existing stem geometry using a three-dimensional FE analysis combined with a shape optimization technique. One of the most important factors in the cemented stem design is to reduce stress in the cement. Hence, in the optimization study, we minimized the largest tensile principal stress in the cement mantle under a physiological loading condition by changing the stem geometry. As the next step, the optimized stem and the existing stem were manufactured to validate the usefulness of the numerical models and the results of the optimization in vitro. In the experimental study, strain gauges were embedded in the cement mantle to measure the strain in the cement mantle adjacent to the stems. The overall trend of the experimental study was in good agreement with the results of the numerical study, and we were able to reduce the largest stress by more than 50% in both shape optimization and strain gauge measurements. Thus, we could validate the usefulness of the numerical models and the results of the optimization using the experimental models. The optimization employed in this study is a useful approach for developing new stem designs.

Optimal experimental design with R

CERN Document Server

Rasch, Dieter; Verdooren, L R; Gebhardt, Albrecht

2011-01-01

Experimental design is often overlooked in the literature of applied and mathematical statistics: statistics is taught and understood as merely a collection of methods for analyzing data. Consequently, experimenters seldom think about optimal design, including prerequisites such as the necessary sample size needed for a precise answer for an experimental question. Providing a concise introduction to experimental design theory, Optimal Experimental Design with R: Introduces the philosophy of experimental design Provides an easy process for constructing experimental designs and calculating necessary sample size using R programs Teaches by example using a custom made R program package: OPDOE Consisting of detailed, data-rich examples, this book introduces experimenters to the philosophy of experimentation, experimental design, and data collection. It gives researchers and statisticians guidance in the construction of optimum experimental designs using R programs, including sample size calculations, hypothesis te...

Experimental validation of additively manufactured optimized shapes for passive cooling

DEFF Research Database (Denmark)

Lazarov, Boyan S.; Sigmund, Ole; Meyer, Knud E.

2018-01-01

This article confirms the superior performance of topology optimized heat sinks compared to lattice designs and suggests simpler manufacturable pin-fin design interpretations. The development is driven by the wide adoption of light-emitting-diode (LED) lamps for industrial and residential lighting....... The presented heat sink solutions are generated by topology optimization, a computational morphogenesis approach with ultimate design freedom, relying on high-performance computing and simulation. Optimized devices exhibit complex and organic-looking topologies which are realized with the help of additive...... manufacturing. To reduce manufacturing cost, a simplified interpretation of the optimized design is produced and validated as well. Numerical and experimental results agree well and indicate that the obtained designs outperform lattice geometries by more than 21%, resulting in a doubling of life expectancy and...

Conceptual design of helium experimental loop

International Nuclear Information System (INIS)

Yu Xingfu; Feng Kaiming

2007-01-01

In a future demonstration fusion power station (DEMO), helium is envisaged as coolant for plasma facing components, such as blanket and dive,or. All these components have a very complex geometry, with many parallel cooling channels, involving a complex helium flow distribution. Test blanket modules (TBM) of this concept will under go various tests in the experimental reactor ITER. For the qualification of TBM, it is indispensable to test mock-ups in a helium loop under realistic pressure and temperature profiles, in order to validate design codes, especially regarding mass flow and heat transition processes in narrow cooling channels. Similar testing must be performed for DEMO blanket, currently under development. A Helium Experimental Loop (HELOOP) is planed to be built for TBM tests. The design parameter of temperature, pressure, flow rate is 550 degree C, 10 MPa, l kg/s respectively. In particular, HELOOP is able to: perform full-scale tests of TBM under realistic conditions; test other components of the He-cooling system in ITER; qualify the purification circuit; obtain information for the design of the ITER cooling system. The main requirements and characteristics of the HELOOP facility and a preliminary conceptual design are described in the paper. (authors)

Design and Experimental Validation of a USBL Underwater Acoustic Positioning System

Directory of Open Access Journals (Sweden)

Joel Reis

2016-09-01

Full Text Available This paper presents the steps for developing a low-cost POrtableNavigation Tool for Underwater Scenarios (PONTUS to be used as a localization device for subsea targets. PONTUS consists of an integrated ultra-short baseline acoustic positioning system aided by an inertial navigation system. Built on a practical design, it can be mounted on an underwater robotic vehicle or be operated by a scuba diver. It also features a graphical user interface that provides information on the tracking of the designated target, in addition to some details on the physical properties inside PONTUS. A full disclosure of the architecture of the tool is first presented, followed by thorough technical descriptions of the hardware components ensemble and the software development process. A series of experiments was carried out to validate the developed prototype, and the results are presented herein, which allow assessing its overall performance.

Design and Experimental Validation of a USBL Underwater Acoustic Positioning System.

Science.gov (United States)

Reis, Joel; Morgado, Marco; Batista, Pedro; Oliveira, Paulo; Silvestre, Carlos

2016-09-14

This paper presents the steps for developing a low-cost POrtableNavigation Tool for Underwater Scenarios (PONTUS) to be used as a localization device for subsea targets. PONTUS consists of an integrated ultra-short baseline acoustic positioning system aided by an inertial navigation system. Built on a practical design, it can be mounted on an underwater robotic vehicle or be operated by a scuba diver. It also features a graphical user interface that provides information on the tracking of the designated target, in addition to some details on the physical properties inside PONTUS. A full disclosure of the architecture of the tool is first presented, followed by thorough technical descriptions of the hardware components ensemble and the software development process. A series of experiments was carried out to validate the developed prototype, and the results are presented herein, which allow assessing its overall performance.

Design, construction, and validation of a scale to measure cyberbullying in a work environment

Directory of Open Access Journals (Sweden)

Luz N. Fernández-López

2018-04-01

Full Text Available The objective of this study was to design, construct, and validate a scale to measure cyberbullying in a work environment. The design used was quantitative, not experimental, and transversal. The research method was based on the Reactive Response Theory. This research produced a validated scale with a sample of the work environment in Puerto Rico. Three analyses were performed: content validity, reliability analysis of the Cronbach alpha coefficient, and the divergent type construct validity. Based on the analysis of the results, the scale was deemed to be useful for the purpose it was designed. Building a scale that measures cyberbullying contributes to the design of new instruments and the revision of existing ones; furthermore, it may serve as the basis for future re- search related to the topic of cyberbullying.

Advanced Reactors-Intermediate Heat Exchanger (IHX) Coupling: Theoretical Modeling and Experimental Validation

Energy Technology Data Exchange (ETDEWEB)

Utgikar, Vivek [Univ. of Idaho, Moscow, ID (United States); Sun, Xiaodong [The Ohio State Univ., Columbus, OH (United States); Christensen, Richard [The Ohio State Univ., Columbus, OH (United States); Sabharwall, Piyush [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-12-29

The overall goal of the research project was to model the behavior of the advanced reactorintermediate heat exchange system and to develop advanced control techniques for off-normal conditions. The specific objectives defined for the project were: 1. To develop the steady-state thermal hydraulic design of the intermediate heat exchanger (IHX); 2. To develop mathematical models to describe the advanced nuclear reactor-IHX-chemical process/power generation coupling during normal and off-normal operations, and to simulate models using multiphysics software; 3. To develop control strategies using genetic algorithm or neural network techniques and couple these techniques with the multiphysics software; 4. To validate the models experimentally The project objectives were accomplished by defining and executing four different tasks corresponding to these specific objectives. The first task involved selection of IHX candidates and developing steady state designs for those. The second task involved modeling of the transient and offnormal operation of the reactor-IHX system. The subsequent task dealt with the development of control strategies and involved algorithm development and simulation. The last task involved experimental validation of the thermal hydraulic performances of the two prototype heat exchangers designed and fabricated for the project at steady state and transient conditions to simulate the coupling of the reactor- IHX-process plant system. The experimental work utilized the two test facilities at The Ohio State University (OSU) including one existing High-Temperature Helium Test Facility (HTHF) and the newly developed high-temperature molten salt facility.

Experimental validation of error in temperature measurements in thin walled ductile iron castings

DEFF Research Database (Denmark)

Pedersen, Karl Martin; Tiedje, Niels Skat

2007-01-01

An experimental analysis has been performed to validate the measurement error of cooling curves measured in thin walled ductile cast iron. Specially designed thermocouples with Ø0.2 mm thermocouple wire in Ø1.6 mm ceramic tube was used for the experiments. Temperatures were measured in plates...

Numerical modeling and experimental validation of thermoplastic composites induction welding

Science.gov (United States)

Palmieri, Barbara; Nele, Luigi; Galise, Francesco

2018-05-01

In this work, a numerical simulation and experimental test of the induction welding of continuous fibre-reinforced thermoplastic composites (CFRTPCs) was provided. The thermoplastic Polyamide 66 (PA66) with carbon fiber fabric was used. Using a dedicated software (JMag Designer), the influence of the fundamental process parameters such as temperature, current and holding time was investigated. In order to validate the results of the simulations, and therefore the numerical model used, experimental tests were carried out, and the temperature values measured during the tests were compared with the aid of an optical pyrometer, with those provided by the numerical simulation. The mechanical properties of the welded joints were evaluated by single lap shear tests.

Automated reasoning applications to design validation and sneak function analysis

International Nuclear Information System (INIS)

Stratton, R.C.

1984-01-01

Argonne National Laboratory (ANL) is actively involved in the LMFBR Man-Machine Integration (MMI) Safety Program. The objective of this program is to enhance the operational safety and reliability of fast-breeder reactors by optimum integration of men and machines through the application of human factors principles and control engineering to the design, operation, and the control environment. ANL is developing methods to apply automated reasoning and computerization in the validation and sneak function analysis process. This project provides the element definitions and relations necessary for an automated reasoner (AR) to reason about design validation and sneak function analysis. This project also provides a demonstration of this AR application on an Experimental Breeder Reactor-II (EBR-II) system, the Argonne Cooling System

Validation of the CATHARE2 code against experimental data from Brayton-cycle plants

International Nuclear Information System (INIS)

Bentivoglio, Fabrice; Tauveron, Nicolas; Geffraye, Genevieve; Gentner, Herve

2008-01-01

In recent years the Commissariat a l'Energie Atomique (CEA) has commissioned a wide range of feasibility studies of future-advanced nuclear reactors, in particular gas-cooled reactors (GCR). The thermohydraulic behaviour of these systems is a key issue for, among other things, the design of the core, the assessment of thermal stresses, and the design of decay heat removal systems. These studies therefore require efficient and reliable simulation tools capable of modelling the whole reactor, including the core, the core vessel, piping, heat exchangers and turbo-machinery. CATHARE2 is a thermal-hydraulic 1D reference safety code developed and extensively validated for the French pressurized water reactors. It has been recently adapted to deal also with gas-cooled reactor applications. In order to validate CATHARE2 for these new applications, CEA has initiated an ambitious long-term experimental program. The foreseen experimental facilities range from small-scale loops for physical correlations, to component technology and system demonstration loops. In the short-term perspective, CATHARE2 is being validated against existing experimental data. And in particular from the German power plants Oberhausen I and II. These facilities have both been operated by the German utility Energie Versorgung Oberhausen (E.V.O.) and their power conversion systems resemble to the high-temperature reactor concepts: Oberhausen I is a 13.75-MWe Brayton-cycle air turbine plant, and Oberhausen II is a 50-MWe Brayton-cycle helium turbine plant. The paper presents these two plants, the adopted CATHARE2 modelling and a comparison between experimental data and code results for both steady state and transient cases

Multiphysics modelling and experimental validation of high concentration photovoltaic modules

International Nuclear Information System (INIS)

Theristis, Marios; Fernández, Eduardo F.; Sumner, Mike; O'Donovan, Tadhg S.

2017-01-01

Highlights: • A multiphysics modelling approach for concentrating photovoltaics was developed. • An experimental campaign was conducted to validate the models. • The experimental results were in good agreement with the models. • The multiphysics modelling allows the concentrator’s optimisation. - Abstract: High concentration photovoltaics, equipped with high efficiency multijunction solar cells, have great potential in achieving cost-effective and clean electricity generation at utility scale. Such systems are more complex compared to conventional photovoltaics because of the multiphysics effect that is present. Modelling the power output of such systems is therefore crucial for their further market penetration. Following this line, a multiphysics modelling procedure for high concentration photovoltaics is presented in this work. It combines an open source spectral model, a single diode electrical model and a three-dimensional finite element thermal model. In order to validate the models and the multiphysics modelling procedure against actual data, an outdoor experimental campaign was conducted in Albuquerque, New Mexico using a high concentration photovoltaic monomodule that is thoroughly described in terms of its geometry and materials. The experimental results were in good agreement (within 2.7%) with the predicted maximum power point. This multiphysics approach is relatively more complex when compared to empirical models, but besides the overall performance prediction it can also provide better understanding of the physics involved in the conversion of solar irradiance into electricity. It can therefore be used for the design and optimisation of high concentration photovoltaic modules.

DC microgrid power flow optimization by multi-layer supervision control. Design and experimental validation

International Nuclear Information System (INIS)

Sechilariu, Manuela; Wang, Bao Chao; Locment, Fabrice; Jouglet, Antoine

2014-01-01

Highlights: • DC microgrid (PV array, storage, power grid connection, DC load) with multi-layer supervision control. • Power balancing following power flow optimization while providing interface for smart grid communication. • Optimization under constraints: storage capability, grid power limitations, grid time-of-use pricing. • Experimental validation of DC microgrid power flow optimization by multi-layer supervision control. • DC microgrid able to perform peak shaving, to avoid undesired injection, and to make full use of locally energy. - Abstract: Urban areas have great potential for photovoltaic (PV) generation, however, direct PV power injection has limitations for high level PV penetration. It induces additional regulations in grid power balancing because of lacking abilities of responding to grid issues such as reducing grid peak consumption or avoiding undesired injections. The smart grid implementation, which is designed to meet these requirements, is facilitated by microgrids development. This paper presents a DC microgrid (PV array, storage, power grid connection, DC load) with multi-layer supervision control which handles instantaneous power balancing following the power flow optimization while providing interface for smart grid communication. The optimization takes into account forecast of PV power production and load power demand, while satisfying constraints such as storage capability, grid power limitations, grid time-of-use pricing and grid peak hour. Optimization, whose efficiency is related to the prediction accuracy, is carried out by mixed integer linear programming. Experimental results show that the proposed microgrid structure is able to control the power flow at near optimum cost and ensures self-correcting capability. It can respond to issues of performing peak shaving, avoiding undesired injection, and making full use of locally produced energy with respect to rigid element constraints

Experimental validation of models for Plasma Focus devices

International Nuclear Information System (INIS)

Rodriguez Palomino, Luis; Gonzalez, Jose; Clausse, Alejandro

2003-01-01

Plasma Focus(PF) Devices are thermonuclear pulsators that produce short pulsed radiation (X-ray, charged particles and neutrons). Since Filippov and Mather, investigations have been used to study plasma properties. Nowadays the interest about PF is focused in technology applications, related to the use of these devices as pulsed neutron sources. In the numerical calculus the Inter institutional PLADEMA (PLAsmas DEnsos MAgnetizados) network is developing three models. Each one is useful in different engineering stages of the Plasma Focus design. One of the main objectives in this work is a comparative study on the influence of the different parameters involved in each models. To validate these results, several experimental measurements under different geometry and initial conditions were performed. (author)

Summary: Experimental validation of real-time fault-tolerant systems

Science.gov (United States)

Iyer, R. K.; Choi, G. S.

1992-01-01

Testing and validation of real-time systems is always difficult to perform since neither the error generation process nor the fault propagation problem is easy to comprehend. There is no better substitute to results based on actual measurements and experimentation. Such results are essential for developing a rational basis for evaluation and validation of real-time systems. However, with physical experimentation, controllability and observability are limited to external instrumentation that can be hooked-up to the system under test. And this process is quite a difficult, if not impossible, task for a complex system. Also, to set up such experiments for measurements, physical hardware must exist. On the other hand, a simulation approach allows flexibility that is unequaled by any other existing method for system evaluation. A simulation methodology for system evaluation was successfully developed and implemented and the environment was demonstrated using existing real-time avionic systems. The research was oriented toward evaluating the impact of permanent and transient faults in aircraft control computers. Results were obtained for the Bendix BDX 930 system and Hamilton Standard EEC131 jet engine controller. The studies showed that simulated fault injection is valuable, in the design stage, to evaluate the susceptibility of computing sytems to different types of failures.

Experimental Engineering: Articulating and Valuing Design Experimentation

DEFF Research Database (Denmark)

Vallgårda, Anna; Grönvall, Erik; Fritsch, Jonas

2017-01-01

In this paper we propose Experimental Engineering as a way to articulate open- ended technological experiments as a legitimate design research practice. Experimental Engineering introduces a move away from an outcome or result driven design process towards an interest in existing technologies and...

Experimental validation of the HARMONIE code

International Nuclear Information System (INIS)

Bernard, A.; Dorsselaere, J.P. van

1984-01-01

An experimental program of deformation, in air, of different groups of subassemblies (7 to 41 subassemblies), was performed on a scale 1 mock-up in the SPX1 geometry, in order to achieve a first experimental validation of the code HARMONIE. The agreement between tests and calculations was suitable, qualitatively for all the groups and quantitatively for regular groups of 19 subassemblies at most. The differences come mainly from friction between pads, and secondly from the foot gaps. (author)

Study design elements for rigorous quasi-experimental comparative effectiveness research.

Science.gov (United States)

Maciejewski, Matthew L; Curtis, Lesley H; Dowd, Bryan

2013-03-01

Quasi-experiments are likely to be the workhorse study design used to generate evidence about the comparative effectiveness of alternative treatments, because of their feasibility, timeliness, affordability and external validity compared with randomized trials. In this review, we outline potential sources of discordance in results between quasi-experiments and experiments, review study design choices that can improve the internal validity of quasi-experiments, and outline innovative data linkage strategies that may be particularly useful in quasi-experimental comparative effectiveness research. There is an urgent need to resolve the debate about the evidentiary value of quasi-experiments since equal consideration of rigorous quasi-experiments will broaden the base of evidence that can be brought to bear in clinical decision-making and governmental policy-making.

Systematic Design Method and Experimental Validation of a 2-DOF Compliant Parallel Mechanism with Excellent Input and Output Decoupling Performances

Directory of Open Access Journals (Sweden)

Yao Jiang

2017-06-01

Full Text Available The output and input coupling characteristics of the compliant parallel mechanism (CPM bring difficulty in the motion control and challenge its high performance and operational safety. This paper presents a systematic design method for a 2-degrees-of-freedom (DOFs CPM with excellent decoupling performance. A symmetric kinematic structure can guarantee a CPM with a complete output decoupling characteristic; input coupling is reduced by resorting to a flexure-based decoupler. This work discusses the stiffness design requirement of the decoupler and proposes a compound flexure hinge as its basic structure. Analytical methods have been derived to assess the mechanical performances of the CPM in terms of input and output stiffness, motion stroke, input coupling degree, and natural frequency. The CPM’s geometric parameters were optimized to minimize the input coupling while ensuring key performance indicators at the same time. The optimized CPM’s performances were then evaluated by using a finite element analysis. Finally, a prototype was constructed and experimental validations were carried out to test the performance of the CPM and verify the effectiveness of the design method. The design procedure proposed in this paper is systematic and can be extended to design the CPMs with other types of motion.

Experimental Investigations of Decentralised Control Design for The Stabilisation of Rotor-Gas Bearings

DEFF Research Database (Denmark)

Theisen, Lukas Roy Svane; Galeazzi, Roberto; Niemann, Hans Henrik

2015-01-01

frequencies. Active lubrication of the journal during operations could enhance the damping and stabilisation characteristics of the sytems, and this could be achieved by means of stabilising controllers. This paper investigates the feasibility of using reduced order models obtained through Grey......-Box identification for the design of stabilising controllers, capable of enabling the active lubrication of the journal. The root locus analysis shows that two different control solutions are feasible for the dampening of the first two eigenfrequencies of the rotor-gas bearing in the horizontal and vertical...... directions. Hardening and softening P-lead controllers are designed based on the models experimentally identified, and salient features of both controllers are discussed. Both controllers are implemented and validated on the physical test rig. Experimental results confirm the validity of the proposed...

A comparative study of soft sensor design for lipid estimation of microalgal photobioreactor system with experimental validation.

Science.gov (United States)

Yoo, Sung Jin; Jung, Dong Hwi; Kim, Jung Hun; Lee, Jong Min

2015-03-01

This study examines the applicability of various nonlinear estimators for online estimation of the lipid concentration in microalgae cultivation system. Lipid is a useful bio-product that has many applications including biofuels and bioactives. However, the improvement of lipid productivity using real-time monitoring and control with experimental validation is limited because measurement of lipid in microalgae is a difficult and time-consuming task. In this study, estimation of lipid concentration from other measurable sources such as biomass or glucose sensor was studied. Extended Kalman filter (EKF), unscented Kalman filter (UKF), and particle filter (PF) were compared in various cases for their applicability to photobioreactor systems. Furthermore, simulation studies to identify appropriate types of sensors for estimating lipid were also performed. Based on the case studies, the most effective case was validated with experimental data and found that UKF and PF with time-varying system noise covariance is effective for microalgal photobioreactor system. Copyright © 2014 Elsevier Ltd. All rights reserved.

A comprehensive collection of experimentally validated primers for Polymerase Chain Reaction quantitation of murine transcript abundance

Directory of Open Access Journals (Sweden)

Wang Xiaowei

2008-12-01

Full Text Available Abstract Background Quantitative polymerase chain reaction (QPCR is a widely applied analytical method for the accurate determination of transcript abundance. Primers for QPCR have been designed on a genomic scale but non-specific amplification of non-target genes has frequently been a problem. Although several online databases have been created for the storage and retrieval of experimentally validated primers, only a few thousand primer pairs are currently present in existing databases and the primers are not designed for use under a common PCR thermal profile. Results We previously reported the implementation of an algorithm to predict PCR primers for most known human and mouse genes. We now report the use of that resource to identify 17483 pairs of primers that have been experimentally verified to amplify unique sequences corresponding to distinct murine transcripts. The primer pairs have been validated by gel electrophoresis, DNA sequence analysis and thermal denaturation profile. In addition to the validation studies, we have determined the uniformity of amplification using the primers and the technical reproducibility of the QPCR reaction using the popular and inexpensive SYBR Green I detection method. Conclusion We have identified an experimentally validated collection of murine primer pairs for PCR and QPCR which can be used under a common PCR thermal profile, allowing the evaluation of transcript abundance of a large number of genes in parallel. This feature is increasingly attractive for confirming and/or making more precise data trends observed from experiments performed with DNA microarrays.

An Experimental Simulation to Validate FEM to Predict Transverse Young’s Modulus of FRP Composites

Directory of Open Access Journals (Sweden)

V. S. Sai

2013-01-01

Full Text Available Finite element method finds application in the analysis of FRP composites due to its versatility in getting the solution for complex cases which are not possible by exact classical analytical approaches. The finite element result is questionable unless it is obtained from converged mesh and properly validated. In the present work specimens are prepared with metallic materials so that the arrangement of fibers is close to hexagonal packing in a matrix as similar arrangement in case of FRP is complex due to the size of fibers. Transverse Young’s moduli of these specimens are determined experimentally. Equivalent FE models are designed and corresponding transverse Young’s moduli are compared with the experimental results. It is observed that the FE values are in good agreement with the experimental results, thus validating FEM for predicting transverse modulus of FRP composites.

Design, Fabrication and Experimental Validation of a Novel Dry-Contact Sensor for Measuring Electroencephalography Signals without Skin Preparation

Directory of Open Access Journals (Sweden)

Chin-Teng Lin

2011-05-01

Full Text Available In the present study, novel dry-contact sensors for measuring electro-encephalography (EEG signals without any skin preparation are designed, fabricated by an injection molding manufacturing process and experimentally validated. Conventional wet electrodes are commonly used to measure EEG signals; they provide excellent EEG signals subject to proper skin preparation and conductive gel application. However, a series of skin preparation procedures for applying the wet electrodes is always required and usually creates trouble for users. To overcome these drawbacks, novel dry-contact EEG sensors were proposed for potential operation in the presence or absence of hair and without any skin preparation or conductive gel usage. The dry EEG sensors were designed to contact the scalp surface with 17 spring contact probes. Each probe was designed to include a probe head, plunger, spring, and barrel. The 17 probes were inserted into a flexible substrate using a one-time forming process via an established injection molding procedure. With these 17 spring contact probes, the flexible substrate allows for high geometric conformity between the sensor and the irregular scalp surface to maintain low skin-sensor interface impedance. Additionally, the flexible substrate also initiates a sensor buffer effect, eliminating pain when force is applied. The proposed dry EEG sensor was reliable in measuring EEG signals without any skin preparation or conductive gel usage, as compared with the conventional wet electrodes.

Design for validation: An approach to systems validation

Science.gov (United States)

Carter, William C.; Dunham, Janet R.; Laprie, Jean-Claude; Williams, Thomas; Howden, William; Smith, Brian; Lewis, Carl M. (Editor)

1989-01-01

Every complex system built is validated in some manner. Computer validation begins with review of the system design. As systems became too complicated for one person to review, validation began to rely on the application of adhoc methods by many individuals. As the cost of the changes mounted and the expense of failure increased, more organized procedures became essential. Attempts at devising and carrying out those procedures showed that validation is indeed a difficult technical problem. The successful transformation of the validation process into a systematic series of formally sound, integrated steps is necessary if the liability inherent in the future digita-system-based avionic and space systems is to be minimized. A suggested framework and timetable for the transformtion are presented. Basic working definitions of two pivotal ideas (validation and system life-cyle) are provided and show how the two concepts interact. Many examples are given of past and present validation activities by NASA and others. A conceptual framework is presented for the validation process. Finally, important areas are listed for ongoing development of the validation process at NASA Langley Research Center.

Design and Experimental Validation of Hydraulic Yaw System for Multi MW Wind Turbine

DEFF Research Database (Denmark)

Stubkier, Søren; Pedersen, Henrik C.; Andersen, Torben Ole

2013-01-01

market. A hydraulic yaw system is such a new technology, and so a mathematical model of the full scale system and test rig system is derived and compared to measurements from the system. This is done in order to have a validated model, which wind turbine manufacturers may use for test in their simulation......To comply with the increasing demands for life time and reliability of wind turbines as these grow in size, new measures needs to be taken in the design of wind turbines and components hereof. One critical point is the initial testing of the components and systems before they are implemented...... in an actual turbine. Full scale hardware testing is both extremely expensive and time consuming, and so the wind turbine industry moves more towards simulations when testing. In order to meet these demands it is necessary with valid models of systems in order to introduce new technologies to the wind turbine...

Validation of designing tools as part of nuclear pump development process

International Nuclear Information System (INIS)

Klemm, T.; Sehr, F.; Spenner, P.; Fritz, J.

2010-01-01

Nuclear pumps are characterized by high safety standards, operational reliability as well as long life cycles. For the design process it is of common use to have a down scaled model pump to qualify operating data and simulate exceptional operating conditions. In case of modifications of the pump design compared to existing reactor coolant pumps a model pump is required to develop methods and tools to design the full scale pump. In the presented case it has a geometry scale of 1:2 regarding the full scale pump size. The experimental data of the model pump is basis for validation of methods and tools which are applied in the designing process of the full scale pump. In this paper the selection of qualified tools and the validation process is demonstrated exemplarily on a cooling circuit. The aim is to predict the resulting flow rate. Tools are chosen for different components depending on the benefit to effort ratio. For elementary flow phenomena such as fluid flow in straight pipes or gaps analytic or empirical laws can be used. For more complex flow situations numerical methods are utilized. Main focus is set on the validation process of the applied numerical flow simulation. In this case not only integral data should be compared, it is also necessary to validate local flow structure of numerical flow simulation to avoid systematic errors in CFD Model generation. Due to complex design internal flow measurements are not possible. On that reason simple comparisons of similar flow test cases are used. Results of this study show, that the flow simulation data closely match measured integral pump and test case data. With this validation it is now possible to qualify CFD simulations as a design tool for the full scale pump in similar cooling circuit. (authors)

D-OPTIMAL EXPERIMENTAL DESIGNS TO TEST FOR DEPARTURE FROM ADDITIVITY IN A FIXED-RATIO MIXTURE RAY.

Science.gov (United States)

Humans are exposed to mixtures of environmental compounds. A regulatory assumption is that the mixtures of chemicals act in an additive manner. However, this assumption requires experimental validation. Traditional experimental designs (full factorial) require a large number of e...

Parametric model of servo-hydraulic actuator coupled with a nonlinear system: Experimental validation

Science.gov (United States)

Maghareh, Amin; Silva, Christian E.; Dyke, Shirley J.

2018-05-01

Hydraulic actuators play a key role in experimental structural dynamics. In a previous study, a physics-based model for a servo-hydraulic actuator coupled with a nonlinear physical system was developed. Later, this dynamical model was transformed into controllable canonical form for position tracking control purposes. For this study, a nonlinear device is designed and fabricated to exhibit various nonlinear force-displacement profiles depending on the initial condition and the type of materials used as replaceable coupons. Using this nonlinear system, the controllable canonical dynamical model is experimentally validated for a servo-hydraulic actuator coupled with a nonlinear physical system.

Design and experimental results of the 1-T Bitter Electromagnet Testing Apparatus (BETA)

Science.gov (United States)

Bates, E. M.; Birmingham, W. J.; Romero-Talamás, C. A.

2018-05-01

The Bitter Electromagnet Testing Apparatus (BETA) is a 1-Tesla (T) technical prototype of the 10 T Adjustable Long Pulsed High-Field Apparatus. BETA's final design specifications are highlighted in this paper which include electromagnetic, thermal, and stress analyses. We discuss here the design and fabrication of BETA's core, vessel, cooling, and electrical subsystems. The electrical system of BETA is composed of a scalable solid-state DC breaker circuit. Experimental results display the stable operation of BETA at 1 T. These results are compared to both analytical design and finite element calculations. Experimental results validate analytical magnet designing methods developed at the Dusty Plasma Laboratory. The theoretical steady state maxima and the limits of BETA's design are explored in this paper.

Design Methodology and Experimental Verification of Serpentine/Folded Waveguide TWTs

Science.gov (United States)

2016-03-17

FW), oscillation, serpentine, stopband, traveling -wave tube (TWT), vacuum electronics. I. INTRODUCTION DEVELOPMENT of high-power broadband vacuum elec...tron devices (VEDs) beyond Ka-band using conventional coupled-cavity and helix traveling -wave tube (TWT) RF cir- cuit fabrication techniques is...bottom plot. III. G-BAND CIRCUIT DESIGN AND EXPERIMENTAL VALIDATION The primary motivation for the G-band amplifier was to develop a high-power broadband

Contact Modelling in Resistance Welding, Part II: Experimental Validation

DEFF Research Database (Denmark)

Song, Quanfeng; Zhang, Wenqi; Bay, Niels

2006-01-01

Contact algorithms in resistance welding presented in the previous paper are experimentally validated in the present paper. In order to verify the mechanical contact algorithm, two types of experiments, i.e. sandwich upsetting of circular, cylindrical specimens and compression tests of discs...... with a solid ring projection towards a flat ring, are carried out at room temperature. The complete algorithm, involving not only the mechanical model but also the thermal and electrical models, is validated by projection welding experiments. The experimental results are in satisfactory agreement...

Experimental Design Research

DEFF Research Database (Denmark)

This book presents a new, multidisciplinary perspective on and paradigm for integrative experimental design research. It addresses various perspectives on methods, analysis and overall research approach, and how they can be synthesized to advance understanding of design. It explores the foundations...... of experimental approaches and their utility in this domain, and brings together analytical approaches to promote an integrated understanding. The book also investigates where these approaches lead to and how they link design research more fully with other disciplines (e.g. psychology, cognition, sociology......, computer science, management). Above all, the book emphasizes the integrative nature of design research in terms of the methods, theories, and units of study—from the individual to the organizational level. Although this approach offers many advantages, it has inherently led to a situation in current...

Validation of Code ASTEC with LIVE-L1 Experimental Results

International Nuclear Information System (INIS)

Bachrata, Andrea

2008-01-01

The severe accidents with core melting are considered at the design stage of project at Generation 3+ of Nuclear Power Plants (NPP). Moreover, there is an effort to apply the severe accident management to the operated NPP. The one of main goals of severe accidents mitigation is corium localization and stabilization. The two strategies that fulfil this requirement are: the in-vessel retention (e.g. AP-600, AP- 1000) and the ex-vessel retention (e.g. EPR). To study the scenario of in-vessel retention, a large experimental program and the integrated codes have been developed. The LIVE-L1 experimental facility studied the formation of melt pools and the melt accumulation in the lower head using different cooling conditions. Nowadays, a new European computer code ASTEC is being developed jointly in France and Germany. One of the important steps in ASTEC development in the area of in-vessel retention of corium is its validation with LIVE-L1 experimental results. Details of the experiment are reported. Results of the ASTEC (module DIVA) application to the analysis of the test are presented. (author)

Modeling and experimental validation of a Hybridized Energy Storage System for automotive applications

Science.gov (United States)

Fiorenti, Simone; Guanetti, Jacopo; Guezennec, Yann; Onori, Simona

2013-11-01

This paper presents the development and experimental validation of a dynamic model of a Hybridized Energy Storage System (HESS) consisting of a parallel connection of a lead acid (PbA) battery and double layer capacitors (DLCs), for automotive applications. The dynamic modeling of both the PbA battery and the DLC has been tackled via the equivalent electric circuit based approach. Experimental tests are designed for identification purposes. Parameters of the PbA battery model are identified as a function of state of charge and current direction, whereas parameters of the DLC model are identified for different temperatures. A physical HESS has been assembled at the Center for Automotive Research The Ohio State University and used as a test-bench to validate the model against a typical current profile generated for Start&Stop applications. The HESS model is then integrated into a vehicle simulator to assess the effects of the battery hybridization on the vehicle fuel economy and mitigation of the battery stress.

Rapid Robot Design Validation, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Energid Technologies will create a comprehensive software infrastructure for rapid validation of robot designs. The software will support push-button validation...

Internal Validity: A Must in Research Designs

Science.gov (United States)

Cahit, Kaya

2015-01-01

In experimental research, internal validity refers to what extent researchers can conclude that changes in dependent variable (i.e. outcome) are caused by manipulations in independent variable. The causal inference permits researchers to meaningfully interpret research results. This article discusses (a) internal validity threats in social and…

Quasi-Experimental Designs for Causal Inference

Science.gov (United States)

Kim, Yongnam; Steiner, Peter

2016-01-01

When randomized experiments are infeasible, quasi-experimental designs can be exploited to evaluate causal treatment effects. The strongest quasi-experimental designs for causal inference are regression discontinuity designs, instrumental variable designs, matching and propensity score designs, and comparative interrupted time series designs. This…

Experimental validation of a heat transfer model for concentrating photovoltaic system

International Nuclear Information System (INIS)

Sendhil Kumar, Natarajan; Matty, Katz; Rita, Ebner; Simon, Weingaertner; Ortrun, Aßländer; Alex, Cole; Roland, Wertz; Tim, Giesen; Tapas Kumar, Mallick

2012-01-01

In this paper, a three dimensional heat transfer model is presented for a novel concentrating photovoltaic design for Active Solar Panel Initiative System (ASPIS). The concentration ratio of two systems (early and integrated prototype) are 5× and 10× respectively, designed for roof-top integrated Photovoltaic systems. ANSYS 12.1, CFX package was effectively used to predict the temperatures of the components of the both ASPIS systems at various boundary conditions. The predicted component temperatures of an early prototype were compared with experimental results of ASPIS, which were carried out in Solecta – Israel and at the Austrian Institute of Technology (AIT) – Austria. It was observed that the solar cell and lens temperature prediction shows good agreement with Solecta measurements. The minimum and maximum deviation of 3.8% and 17.9% were observed between numerical and Solecta measurements and the maximum deviations of 16.9% were observed between modeling and AIT measurements. Thus, the developed validated thermal model enables to predict the component temperatures for concentrating photovoltaic systems. - Highlights: ► Experimentally validated heat transfer model for concentrating Photovoltaic system developed. ► Predictions of solar cell temperatures for parallactic tracking CPV system for roof integration. ► The ASPIS module contains 2 mm wide 216 solar cells manufactured based on SATURN technology. ► A solar cell temperature of 44 °C was predicted for solar radiation intensity was 1000 W/m 2 and ambient temperature was 20 °C. ► Average deviation was 6% and enabled to predict temperature of any CPV system.

VALIDATION OF SIMULATION MODELS FOR DIFFERENTLY DESIGNED HEAT-PIPE EVACUATED TUBULAR COLLECTORS

DEFF Research Database (Denmark)

Fan, Jianhua; Dragsted, Janne; Furbo, Simon

2007-01-01

Differently designed heat-pipe evacuated tubular collectors have been investigated theoretically and experimentally. The theoretical work has included development of two TRNSYS [1] simulation models for heat-pipe evacuated tubular collectors utilizing solar radiation from all directions. One model...... coating on both sides. The input to the models is thus not a simple collector efficiency expression but the actual collector geometry. In this study, the TRNSYS models are validated with measurements for four differently designed heat-pipe evacuated tubular collectors. The collectors are produced...

Quasi-experimental study designs series-paper 6: risk of bias assessment.

Science.gov (United States)

Waddington, Hugh; Aloe, Ariel M; Becker, Betsy Jane; Djimeu, Eric W; Hombrados, Jorge Garcia; Tugwell, Peter; Wells, George; Reeves, Barney

2017-09-01

Rigorous and transparent bias assessment is a core component of high-quality systematic reviews. We assess modifications to existing risk of bias approaches to incorporate rigorous quasi-experimental approaches with selection on unobservables. These are nonrandomized studies using design-based approaches to control for unobservable sources of confounding such as difference studies, instrumental variables, interrupted time series, natural experiments, and regression-discontinuity designs. We review existing risk of bias tools. Drawing on these tools, we present domains of bias and suggest directions for evaluation questions. The review suggests that existing risk of bias tools provide, to different degrees, incomplete transparent criteria to assess the validity of these designs. The paper then presents an approach to evaluating the internal validity of quasi-experiments with selection on unobservables. We conclude that tools for nonrandomized studies of interventions need to be further developed to incorporate evaluation questions for quasi-experiments with selection on unobservables. Copyright © 2017 Elsevier Inc. All rights reserved.

An Empirical Study of Parameter Estimation for Stated Preference Experimental Design

Directory of Open Access Journals (Sweden)

Fei Yang

2014-01-01

Full Text Available The stated preference experimental design can affect the reliability of the parameters estimation in discrete choice model. Some scholars have proposed some new experimental designs, such as D-efficient, Bayesian D-efficient. But insufficient empirical research has been conducted on the effectiveness of these new designs and there has been little comparative analysis of the new designs against the traditional designs. In this paper, a new metro connecting Chengdu and its satellite cities is taken as the research subject to demonstrate the validity of the D-efficient and Bayesian D-efficient design. Comparisons between these new designs and orthogonal design were made by the fit of model and standard deviation of parameters estimation; then the best model result is obtained to analyze the travel choice behavior. The results indicate that Bayesian D-efficient design works better than D-efficient design. Some of the variables can affect significantly the choice behavior of people, including the waiting time and arrival time. The D-efficient and Bayesian D-efficient design for MNL can acquire reliability result in ML model, but the ML model cannot develop the theory advantages of these two designs. Finally, the metro can handle over 40% passengers flow if the metro will be operated in the future.

High Level Analysis, Design and Validation of Distributed Mobile Systems with CoreASM

Science.gov (United States)

Farahbod, R.; Glässer, U.; Jackson, P. J.; Vajihollahi, M.

System design is a creative activity calling for abstract models that facilitate reasoning about the key system attributes (desired requirements and resulting properties) so as to ensure these attributes are properly established prior to actually building a system. We explore here the practical side of using the abstract state machine (ASM) formalism in combination with the CoreASM open source tool environment for high-level design and experimental validation of complex distributed systems. Emphasizing the early phases of the design process, a guiding principle is to support freedom of experimentation by minimizing the need for encoding. CoreASM has been developed and tested building on a broad scope of applications, spanning computational criminology, maritime surveillance and situation analysis. We critically reexamine here the CoreASM project in light of three different application scenarios.

Control Structure Impact on the Flying Performance of the Multi-Rotor VTOL Platform - Design, Analysis and Experimental Validation

Directory of Open Access Journals (Sweden)

Roman Czyba

2013-01-01

Full Text Available The aim of this research is to examine the different control strategies for the unmanned aerial vehicles (UAV. The control task is formulated as an angular stabilization of the four rotor platform, and also as a tracking problem of chosen state variables. The PID algorithm has been considered in three structures in respect of the optimal control signal applied to the actuators. For better performance of the quadrotor in hover mode the cascade control system has been proposed. The simulation results of attitude control with different PID controller architectures are presented, and confirm the effectiveness of the proposed control structure and theoretical expectations. Moreover, the design and the practical realization of the control architecture on the experimental aerial vehicle are described. The fast prototyping method together with Matlab/Simulink software and DAQ hardware are used for both evolution and validation of control algorithms. The capacity of the attitude stabilization system is important in the development process of more advanced functionality of autonomous flying vehicles; therefore it needs to be highlighted and taken into careful consideration.

Experimental validation of optimum resistance moment of concrete ...

African Journals Online (AJOL)

Experimental validation of optimum resistance moment of concrete slabs reinforced ... other solutions to combat corrosion problems in steel reinforced concrete. ... Eight specimens of two-way spanning slabs reinforced with CFRP bars were ...

Model based multivariable controller for large scale compression stations. Design and experimental validation on the LHC 18KW cryorefrigerator

Energy Technology Data Exchange (ETDEWEB)

Bonne, François; Bonnay, Patrick [INAC, SBT, UMR-E 9004 CEA/UJF-Grenoble, 17 rue des Martyrs, 38054 Grenoble (France); Alamir, Mazen [Gipsa-Lab, Control Systems Department, CNRS-University of Grenoble, 11, rue des Mathématiques, BP 46, 38402 Saint Martin d' Hères (France); Bradu, Benjamin [CERN, CH-1211 Genève 23 (Switzerland)

2014-01-29

In this paper, a multivariable model-based non-linear controller for Warm Compression Stations (WCS) is proposed. The strategy is to replace all the PID loops controlling the WCS with an optimally designed model-based multivariable loop. This new strategy leads to high stability and fast disturbance rejection such as those induced by a turbine or a compressor stop, a key-aspect in the case of large scale cryogenic refrigeration. The proposed control scheme can be used to have precise control of every pressure in normal operation or to stabilize and control the cryoplant under high variation of thermal loads (such as a pulsed heat load expected to take place in future fusion reactors such as those expected in the cryogenic cooling systems of the International Thermonuclear Experimental Reactor ITER or the Japan Torus-60 Super Advanced fusion experiment JT-60SA). The paper details how to set the WCS model up to synthesize the Linear Quadratic Optimal feedback gain and how to use it. After preliminary tuning at CEA-Grenoble on the 400W@1.8K helium test facility, the controller has been implemented on a Schneider PLC and fully tested first on the CERN's real-time simulator. Then, it was experimentally validated on a real CERN cryoplant. The efficiency of the solution is experimentally assessed using a reasonable operating scenario of start and stop of compressors and cryogenic turbines. This work is partially supported through the European Fusion Development Agreement (EFDA) Goal Oriented Training Program, task agreement WP10-GOT-GIRO.

Experimental validation of thermo-chemical algorithm for a simulation of pultrusion processes

Science.gov (United States)

Barkanov, E.; Akishin, P.; Miazza, N. L.; Galvez, S.; Pantelelis, N.

2018-04-01

To provide better understanding of the pultrusion processes without or with temperature control and to support the pultrusion tooling design, an algorithm based on the mixed time integration scheme and nodal control volumes method has been developed. At present study its experimental validation is carried out by the developed cure sensors measuring the electrical resistivity and temperature on the profile surface. By this verification process the set of initial data used for a simulation of the pultrusion process with rod profile has been successfully corrected and finally defined.

Experimental design optimisation: theory and application to estimation of receptor model parameters using dynamic positron emission tomography

International Nuclear Information System (INIS)

Delforge, J.; Syrota, A.; Mazoyer, B.M.

1989-01-01

General framework and various criteria for experimental design optimisation are presented. The methodology is applied to estimation of receptor-ligand reaction model parameters with dynamic positron emission tomography data. The possibility of improving parameter estimation using a new experimental design combining an injection of the β + -labelled ligand and an injection of the cold ligand is investigated. Numerical simulations predict remarkable improvement in the accuracy of parameter estimates with this new experimental design and particularly the possibility of separate estimations of the association constant (k +1 ) and of receptor density (B' max ) in a single experiment. Simulation predictions are validated using experimental PET data in which parameter uncertainties are reduced by factors ranging from 17 to 1000. (author)

Simulation and experimental validation of the performance of a absorption refrigerator

International Nuclear Information System (INIS)

Olbricht, Michael; Luke, Andrea

2015-01-01

The two biggest obstacles to a stronger market penetration of absorption refrigerators are their high cost and the size of the apparatus, which are due to the inaccurate methods for plant design. In order to contribute to an improved design a thermodynamic model is presented to describe the performance of a absorption refrigerator with the working fluid water/lithium. In this model, the processes are displayed in the single apparatus and coupled to each other in the systemic context. Thereby the interactions between the apparatus can specifically investigated and thus the process limiting component can be identified under the respective conditions. A validation of the simulation model and the boundary conditions used is done based on experimental data operating a self-developed absorption refrigerator. In the simulation, the heat transfer surfaces in accordance with the real system can be specified. The heat transport is taken into account based on typical values for the heat transfer in the individual apparatuses. Simulation results show good agreement with the experimental data. The physical relationships and influences externally defined operating parameters are correctly reproduced. Due to the chosen low heat transfer coefficient, the calculated cooling capacities by the model are below the experimentally measured. Finally, the possibilities and limitations are discussed by using the model and further improvement possibilities are suggested. [de

Integral Reactor Containment Condensation Model and Experimental Validation

Energy Technology Data Exchange (ETDEWEB)

Wu, Qiao [Oregon State Univ., Corvallis, OR (United States); Corradini, Michael [Univ. of Wisconsin, Madison, WI (United States)

2016-05-02

This NEUP funded project, NEUP 12-3630, is for experimental, numerical and analytical studies on high-pressure steam condensation phenomena in a steel containment vessel connected to a water cooling tank, carried out at Oregon State University (OrSU) and the University of Wisconsin at Madison (UW-Madison). In the three years of investigation duration, following the original proposal, the planned tasks have been completed: (1) Performed a scaling study for the full pressure test facility applicable to the reference design for the condensation heat transfer process during design basis accidents (DBAs), modified the existing test facility to route the steady-state secondary steam flow into the high pressure containment for controllable condensation tests, and extended the operations at negative gage pressure conditions (OrSU). (2) Conducted a series of DBA and quasi-steady experiments using the full pressure test facility to provide a reliable high pressure condensation database (OrSU). (3) Analyzed experimental data and evaluated condensation model for the experimental conditions, and predicted the prototypic containment performance under accidental conditions (UW-Madison). A film flow model was developed for the scaling analysis, and the results suggest that the 1/3 scaled test facility covers large portion of laminar film flow, leading to a lower average heat transfer coefficient comparing to the prototypic value. Although it is conservative in reactor safety analysis, the significant reduction of heat transfer coefficient (50%) could under estimate the prototypic condensation heat transfer rate, resulting in inaccurate prediction of the decay heat removal capability. Further investigation is thus needed to quantify the scaling distortion for safety analysis code validation. Experimental investigations were performed in the existing MASLWR test facility at OrST with minor modifications. A total of 13 containment condensation tests were conducted for pressure

NUMERICAL MODELLING AND EXPERIMENTAL INFLATION VALIDATION OF A BIAS TWO-WHEEL TIRE

Directory of Open Access Journals (Sweden)

CHUNG KET THEIN

2016-02-01

Full Text Available This paper presents a parametric study on the development of a computational model for bias two-wheel tire through finite element analysis (FEA. An 80/90- 17 bias two-wheel tire was adopted which made up of four major layers of rubber compound with different material properties to strengthen the structure. Mooney-Rivlin hyperelastic model was applied to represent the behaviour of incompressible rubber compound. A 3D tire model was built for structural static finite element analysis. The result was validated from the inflation analysis. Structural static finite element analysis method is suitable for evaluation of the tire design and improvement of the tire behaviour to desired performance. Experimental tire was inflated at various pressures and the geometry between numerical and experimental tire were compared. There are good agreements between numerical simulation model and the experiment results. This indicates that the simulation model can be applied to the bias two-wheel tire design in order to predict the tire behaviour and improve its mechanical characteristics.

Dynamic model with experimental validation of a biogas-fed SOFC plant

International Nuclear Information System (INIS)

D'Andrea, G.; Gandiglio, M.; Lanzini, A.; Santarelli, M.

2017-01-01

Highlights: • 60% of DIR into the SOFC anode reduces the air blower parasitic losses by 14%. • PID-controlled cathode airflow enables fast thermal regulation of the SOFC. • Stack overheating occurs due to unexpected reductions in the cathode airflow. • Current ramp rates higher than +0.30 A/min lead to an excessive stack overheating. - Abstract: The dynamic model of a poly-generation system based on a biogas-fed solid oxide fuel cell (SOFC) plant is presented in this paper. The poly-generation plant was developed in the framework of the FP7 EU-funded project SOFCOM ( (www.sofcom.eu)), which consists of a fuel-cell based polygeneration plant with CO_2 capture and re-use. CO_2 is recovered from the anode exhaust of the SOFC (after oxy-combustion, cooling and water condensation) and the Carbon is fixed in the form of micro-algae in a tubular photobioreactor. This work focuses on the dynamic operation of the SOFC module running on steam-reformed biogas. Both steady state and dynamic operation of the fuel cell stack and the related Balance-of-Plant (BoP) has been modeled in order to simulate the thermal behavior and performance of the system. The model was validated against experimental data gathered during the operation of the SOFCOM proof-of-concept showing good agreement with the experimental data. The validated model has been used to investigate further on the harsh off-design operation of the proof-of-concept. Simulation results provide guidelines for an improved design of the control system of the plant, highlighting the feasible operating region under safe conditions and means to maximize the overall system efficiency.

Guided exploration of physically valid shapes for furniture design

KAUST Repository

Umetani, Nobuyuki

2012-07-01

Geometric modeling and the physical validity of shapes are traditionally considered independently. This makes creating aesthetically pleasing yet physically valid models challenging. We propose an interactive design framework for efficient and intuitive exploration of geometrically and physically valid shapes. During any geometric editing operation, the proposed system continuously visualizes the valid range of the parameter being edited. When one or more constraints are violated after an operation, the system generates multiple suggestions involving both discrete and continuous changes to restore validity. Each suggestion also comes with an editing mode that simultaneously adjusts multiple parameters in a coordinated way to maintain validity. Thus, while the user focuses on the aesthetic aspects of the design, our computational design framework helps to achieve physical realizability by providing active guidance to the user. We demonstrate our framework on plankbased furniture design with nail-joint and frictional constraints. We use our system to design a range of examples, conduct a user study, and also fabricate a physical prototype to test the validity and usefulness of the system. © 2012 ACM 0730-0301/2012/08- ART86.

Experimental Validation and Model Verification for a Novel Geometry ICPC Solar Collector

DEFF Research Database (Denmark)

Perers, Bengt; Duff, William S.; Daosukho, Jirachote

A novel geometry ICPC solar collector was developed at the University of Chicago and Colorado State University. A ray tracing model has been designed to investigate the optical performance of both the horizontal and vertical fin versions of this collector. Solar radiation is modeled as discrete...... to the desired incident angle of the sun’s rays, performance of the novel ICPC solar collector at various specified angles along the transverse and longitudinal evacuated tube directions were experimentally determined. To validate the ray tracing model, transverse and longitudinal performance predictions...... at the corresponding specified incident angles are compared to the Sandia results. A 100 m2 336 Novel ICPC evacuated tube solar collector array has been in continuous operation at a demonstration project in Sacramento California since 1998. Data from the initial operation of the array are used to further validate...

Experimental Validation of a Permeability Model for Enrichment Membranes

International Nuclear Information System (INIS)

Orellano, Pablo; Brasnarof, Daniel; Florido Pablo

2003-01-01

An experimental loop with a real scale diffuser, in a single enrichment-stage configuration, was operated with air at different process conditions, in order to characterize the membrane permeability.Using these experimental data, an analytical geometric-and-morphologic-based model was validated.It is conclude that a new set of independent measurements, i.e. enrichment, is necessary in order to fully characterize diffusers, because of its internal parameters are not univocally determinated with permeability experimental data only

Absorber and regenerator models for liquid desiccant air conditioning systems. Validation and comparison using experimental data

Energy Technology Data Exchange (ETDEWEB)

Krause, M.; Heinzen, R.; Jordan, U.; Vajen, K. [Kassel Univ., Inst. of Thermal Engineering, Kassel (Germany); Saman, W.; Halawa, E. [Sustainable Energy Centre, Univ. of South Australia, Mawson Lakes, Adelaide (Australia)

2008-07-01

Solar assisted air conditioning systems using liquid desiccants represent a promising option to decrease high summer energy demand caused by electrically driven vapor compression machines. The main components of liquid desiccant systems are absorbers for dehumidifying and cooling of supply air and regenerators for concentrating the desiccant. However, high efficient and validated reliable components are required and the design and operation have to be adjusted to each respective building design, location, and user demand. Simulation tools can help to optimize component and system design. The present paper presents new developed numerical models for absorbers and regenerators, as well as experimental data of a regenerator prototype. The models have been compared with a finite-difference method model as well as experimental data. The data are gained from the regenerator prototype presented and an absorber presented in the literature. (orig.)

Quasi experimental designs in pharmacist intervention research.

Science.gov (United States)

Krass, Ines

2016-06-01

Background In the field of pharmacist intervention research it is often difficult to conform to the rigorous requirements of the "true experimental" models, especially the requirement of randomization. When randomization is not feasible, a practice based researcher can choose from a range of "quasi-experimental designs" i.e., non-randomised and at time non controlled. Objective The aim of this article was to provide an overview of quasi-experimental designs, discuss their strengths and weaknesses and to investigate their application in pharmacist intervention research over the previous decade. Results In the literature quasi experimental studies may be classified into five broad categories: quasi-experimental design without control groups; quasi-experimental design that use control groups with no pre-test; quasi-experimental design that use control groups and pre-tests; interrupted time series and stepped wedge designs. Quasi-experimental study design has consistently featured in the evolution of pharmacist intervention research. The most commonly applied of all quasi experimental designs in the practice based research literature are the one group pre-post-test design and the non-equivalent control group design i.e., (untreated control group with dependent pre-tests and post-tests) and have been used to test the impact of pharmacist interventions in general medications management as well as in specific disease states. Conclusion Quasi experimental studies have a role to play as proof of concept, in the pilot phases of interventions when testing different intervention components, especially in complex interventions. They serve to develop an understanding of possible intervention effects: while in isolation they yield weak evidence of clinical efficacy, taken collectively, they help build a body of evidence in support of the value of pharmacist interventions across different practice settings and countries. However, when a traditional RCT is not feasible for

Neuroinflammatory targets and treatments for epilepsy validated in experimental models.

Science.gov (United States)

Aronica, Eleonora; Bauer, Sebastian; Bozzi, Yuri; Caleo, Matteo; Dingledine, Raymond; Gorter, Jan A; Henshall, David C; Kaufer, Daniela; Koh, Sookyong; Löscher, Wolfgang; Louboutin, Jean-Pierre; Mishto, Michele; Norwood, Braxton A; Palma, Eleonora; Poulter, Michael O; Terrone, Gaetano; Vezzani, Annamaria; Kaminski, Rafal M

2017-07-01

A large body of evidence that has accumulated over the past decade strongly supports the role of inflammation in the pathophysiology of human epilepsy. Specific inflammatory molecules and pathways have been identified that influence various pathologic outcomes in different experimental models of epilepsy. Most importantly, the same inflammatory pathways have also been found in surgically resected brain tissue from patients with treatment-resistant epilepsy. New antiseizure therapies may be derived from these novel potential targets. An essential and crucial question is whether targeting these molecules and pathways may result in anti-ictogenesis, antiepileptogenesis, and/or disease-modification effects. Therefore, preclinical testing in models mimicking relevant aspects of epileptogenesis is needed to guide integrated experimental and clinical trial designs. We discuss the most recent preclinical proof-of-concept studies validating a number of therapeutic approaches against inflammatory mechanisms in animal models that could represent novel avenues for drug development in epilepsy. Finally, we suggest future directions to accelerate preclinical to clinical translation of these recent discoveries. Wiley Periodicals, Inc. © 2017 International League Against Epilepsy.

Artificial intelligence applications to design validation and sneak function analysis

International Nuclear Information System (INIS)

Stratton, R.C.

1985-01-01

An objective of the US space reactor program is to design systems with high reliability and safety of control over long operating lifetimes. Argonne National Laboratory (ANL) is a participant in the National Man-Machine Integration (MMI) program for Liquid Metal Fast Breeder Reactors (LMFBR). A purpose of this program is to promote the development of concepts and technologies that enhance the operational safety and reliability of fast-breeder reactors. Much of the work is directly applicable to the space reactor program. This paper reports on one of the MMI projects being developed by ANL. The project reported pertains to an automated system that demonstrates the use of artificial intelligence (AI) for design validation (DA) and sneak function analysis (SFA). The AI system models the design specification and the physical design of the cooling process assigned to the Argon Cooling System (ACS) at Experimental Breeder Reactor II (EBR-II). The models are developed using heuristic knowledge and natural laws. 13 refs

Development and Validation of a Hypersonic Vehicle Design Tool Based On Waverider Design Technique

Science.gov (United States)

Dasque, Nastassja

Methodologies for a tool capable of assisting design initiatives for practical waverider based hypersonic vehicles were developed and validated. The design space for vehicle surfaces was formed using an algorithm that coupled directional derivatives with the conservation laws to determine a flow field defined by a set of post-shock streamlines. The design space is used to construct an ideal waverider with a sharp leading edge. A blunting method was developed to modify the ideal shapes to a more practical geometry for real-world application. Empirical and analytical relations were then systematically applied to the resulting geometries to determine local pressure, skin-friction and heat flux. For the ideal portion of the geometry, flat plate relations for compressible flow were applied. For the blunted portion of the geometry modified Newtonian theory, Fay-Riddell theory and Modified Reynolds analogy were applied. The design and analysis methods were validated using analytical solutions as well as empirical and numerical data. The streamline solution for the flow field generation technique was compared with a Taylor-Maccoll solution and showed very good agreement. The relationship between the local Stanton number and skin friction coefficient with local Reynolds number along the ideal portion of the body showed good agreement with experimental data. In addition, an automated grid generation routine was formulated to construct a structured mesh around resulting geometries in preparation for Computational Fluid Dynamics analysis. The overall analysis of the waverider body using the tool was then compared to CFD studies. The CFD flow field showed very good agreement with the design space. However, the distribution of the surface properties was near CFD results but did not have great agreement.

Measuring and Advancing Experimental Design Ability in an Introductory Course without Altering Existing Lab Curriculum

Directory of Open Access Journals (Sweden)

Ryan A. Shanks

2017-05-01

Full Text Available Introductory biology courses provide an important opportunity to prepare students for future courses, yet existing cookbook labs, although important in their own way, fail to provide many of the advantages of semester-long research experiences. Engaging, authentic research experiences aid biology students in meeting many learning goals. Therefore, overlaying a research experience onto the existing lab structure allows faculty to overcome barriers involving curricular change. Here we propose a working model for this overlay design in an introductory biology course and detail a means to conduct this lab with minimal increases in student and faculty workloads. Furthermore, we conducted exploratory factor analysis of the Experimental Design Ability Test (EDAT and uncovered two latent factors which provide valid means to assess this overlay model’s ability to increase advanced experimental design abilities. In a pre-test/post-test design, we demonstrate significant increases in both basic and advanced experimental design abilities in an experimental and comparison group. We measured significantly higher gains in advanced experimental design understanding in students in the experimental group. We believe this overlay model and EDAT factor analysis contribute a novel means to conduct and assess the effectiveness of authentic research experiences in an introductory course without major changes to the course curriculum and with minimal increases in faculty and student workloads.

Experimental validation of tape springs to be used as thin-walled space structures

Science.gov (United States)

Oberst, S.; Tuttle, S. L.; Griffin, D.; Lambert, A.; Boyce, R. R.

2018-04-01

With the advent of standardised launch geometries and off-the-shelf payloads, space programs utilising nano-satellite platforms are growing worldwide. Thin-walled, flexible and self-deployable structures are commonly used for antennae, instrument booms or solar panels owing to their lightweight, ideal packaging characteristics and near zero energy consumption. However their behaviour in space, in particular in Low Earth Orbits with continually changing environmental conditions, raises many questions. Accurate numerical models, which are often not available due to the difficulty of experimental testing under 1g-conditions, are needed to answer these questions. In this study, we present on-earth experimental validations, as a starting point to study the response of a tape spring as a representative of thin-walled flexible structures under static and vibrational loading. Material parameters of tape springs in a singly (straight, open cylinder) and a doubly curved design, are compared to each other by combining finite element calculations, with experimental laser vibrometry within a single and multi-stage model updating approach. While the determination of the Young's modulus is unproblematic, the damping is found to be inversely proportional to deployment length. With updated material properties the buckling instability margin is calculated using different slenderness ratios. Results indicate a high sensitivity of thin-walled structures to miniscule perturbations, which makes proper experimental testing a key requirement for stability prediction on thin-elastic space structures. The doubly curved tape spring provides closer agreement with experimental results than a straight tape spring design.

Experimental design a chemometric approach

CERN Document Server

Deming, SN

1987-01-01

Now available in a paperback edition is a book which has been described as ``...an exceptionally lucid, easy-to-read presentation... would be an excellent addition to the collection of every analytical chemist. I recommend it with great enthusiasm.'' (Analytical Chemistry). Unlike most current textbooks, it approaches experimental design from the point of view of the experimenter, rather than that of the statistician. As the reviewer in `Analytical Chemistry' went on to say: ``Deming and Morgan should be given high praise for bringing the principles of experimental design to the level of the p

Optimization of Protease Production from Aspergillus Oryzae Sp. Using Box-Behnken Experimental Design

Directory of Open Access Journals (Sweden)

G. Srinu Babu

2007-01-01

Full Text Available Protease production by Aspergillus oryzae was optimized in shake-flask cultures using Box-Behnken experimental design. An empirical model was developed through response surface methodology to describe the relationship between tested variable (peptone, glucose, soyabeanmeal and pH. Maximum enzyme activity was attained with Peptone at 4 g∕L; temperature at 30 °C glucose at 6 g∕L; 30 °C and pH at 10. Experimental verification of the model showed a validation of 95%, which is more than 3-fold increase compare to the basal medium.

Chemical-Based Formulation Design: Virtual Experimentation

DEFF Research Database (Denmark)

Conte, Elisa; Gani, Rafiqul

This paper presents a software, the virtual Product-Process Design laboratory (virtual PPD-lab) and the virtual experimental scenarios for design/verification of consumer oriented liquid formulated products where the software can be used. For example, the software can be employed for the design......, the additives and/or their mixtures (formulations). Therefore, the experimental resources can focus on a few candidate product formulations to find the best product. The virtual PPD-lab allows various options for experimentations related to design and/or verification of the product. For example, the selection...... design, model adaptation). All of the above helps to perform virtual experiments by blending chemicals together and observing their predicted behaviour. The paper will highlight the application of the virtual PPD-lab in the design and/or verification of different consumer products (paint formulation...

Computational Design of Creep-Resistant Alloys and Experimental Validation in Ferritic Superalloys

Energy Technology Data Exchange (ETDEWEB)

Liaw, Peter

2014-12-31

A new class of ferritic superalloys containing B2-type zones inside parent L21-type precipitates in a disordered solid-solution matrix, also known as a hierarchical-precipitate strengthened ferritic alloy (HPSFA), has been developed for high-temperature structural applications in fossil-energy power plants. These alloys were designed by the addition of the Ti element into a previously-studied NiAl-strengthened ferritic alloy (denoted as FBB8 in this study). In the present research, systematic investigations, including advanced experimental techniques, first-principles calculations, and numerical simulations, have been integrated and conducted to characterize the complex microstructures and excellent creep resistance of HPSFAs. The experimental techniques include transmission-electron microscopy, scanningtransmission- electron microscopy, neutron diffraction, and atom-probe tomography, which provide detailed microstructural information of HPSFAs. Systematic tension/compression creep tests revealed that HPSFAs exhibit the superior creep resistance, compared with the FBB8 and conventional ferritic steels (i.e., the creep rates of HPSFAs are about 4 orders of magnitude slower than the FBB8 and conventional ferritic steels.) First-principles calculations include interfacial free energies, anti-phase boundary (APB) free energies, elastic constants, and impurity diffusivities in Fe. Combined with kinetic Monte- Carlo simulations of interdiffusion coefficients, and the integration of computational thermodynamics and kinetics, these calculations provide great understanding of thermodynamic and mechanical properties of HPSFAs. In addition to the systematic experimental approach and first-principles calculations, a series of numerical tools and algorithms, which assist in the optimization of creep properties of ferritic superalloys, are utilized and developed. These numerical simulation results are compared with the available experimental data and previous first

HAMMLAB 1999 experimental control room: design - design rationale - experiences

International Nuclear Information System (INIS)

Foerdestroemmen, N. T.; Meyer, B. D.; Saarni, R.

1999-01-01

A presentation of HAMMLAB 1999 experimental control room, and the accumulated experiences gathered in the areas of design and design rationale as well as user experiences. It is concluded that HAMMLAB 1999 experimental control room is a realistic, compact and efficient control room well suited as an Advanced NPP Control Room (ml)

Experimental validation of an ultrasonic flowmeter for unsteady flows

Science.gov (United States)

Leontidis, V.; Cuvier, C.; Caignaert, G.; Dupont, P.; Roussette, O.; Fammery, S.; Nivet, P.; Dazin, A.

2018-04-01

An ultrasonic flowmeter was developed for further applications in cryogenic conditions and for measuring flow rate fluctuations in the range of 0 to 70 Hz. The prototype was installed in a flow test rig, and was validated experimentally both in steady and unsteady water flow conditions. A Coriolis flowmeter was used for the calibration under steady state conditions, whereas in the unsteady case the validation was done simultaneously against two methods: particle image velocimetry (PIV), and with pressure transducers installed flush on the wall of the pipe. The results show that the developed flowmeter and the proposed methodology can accurately measure the frequency and amplitude of unsteady fluctuations in the experimental range of 0-9 l s-1 of the mean main flow rate and 0-70 Hz of the imposed disturbances.

Numerical calibration and experimental validation of a PCM-Air heat exchanger model

International Nuclear Information System (INIS)

Stathopoulos, N.; El Mankibi, M.; Santamouris, Mattheos

2017-01-01

Highlights: • Development of a PCM-Air heat exchanger experimental unit and its numerical model. • Differential Scanning Calorimetry for PCM properties. • Ineptitude of DSC obtained heat capacity curves. • Creation of adequate heat capacity curves depending on heat transfer rates. • Confrontation of numerical and experimental results and validation of the model. - Abstract: Ambitious goals have been set at international, European and French level for energy consumption and greenhouse gas emissions decrease of the building sector. Achieving them requires renewable energy integration, a technology that presents however an important drawback: intermittent energy production. In response, thermal energy storage (TES) technology applications have been developed in order to correlate energy production and consumption of the building. Phase Change Materials (PCMs) have been widely used in TES applications as they offer a high storage density and adequate phase change temperature range. It is important to accurately know the thermophysical properties of the PCM, both for experimental (system design) and numerical (correct prediction) purposes. In this paper, the fabrication of a PCM – Air experimental prototype is presented at first, along with the development of a numerical model simulating the downstream temperature evolution of the heat exchanger. Particular focus is given to the calibration method and the validation of the model using experimental characterization results. Differential scanning calorimetry (DSC) is used to define the thermal properties of the PCM. Initial numerical results are underestimated compared to experimental ones. Various factors were investigated, pointing to the ineptitude of the heat capacity parameter, as DSC results depend on heating/cooling rates. Adequate heat capacity curves were empirically determined, depending on heat transfer rates and based on DSC results and experimental observations. The results of the proposed model

Experimental Validation of the LHC Helium Relief System Flow Modeling

CERN Document Server

Fydrych, J; Riddone, G

2006-01-01

In case of simultaneous resistive transitions in a whole sector of magnets in the Large Hadron Collider, the helium would be vented from the cold masses to a dedicated recovery system. During the discharge the cold helium will eventually enter a pipe at room temperature. During the first period of the flow the helium will be heated intensely due to the pipe heat capacity. To study the changes of the helium thermodynamic and flow parameters we have simulated numerically the most critical flow cases. To verify and validate numerical results, a dedicated laboratory test rig representing the helium relief system has been designed and commissioned. Both numerical and experimental results allow us to determine the distributions of the helium parameters along the pipes as well as mechanical strains and stresses.

An Experimental Design of Bypass Magneto-Rheological (MR) damper

Science.gov (United States)

Rashid, MM; Aziz, Mohammad Abdul; Raisuddin Khan, Md.

2017-11-01

The magnetorheological (MR) fluid bypass damper fluid flow through a bypass by utilizing an external channel which allows the controllability of MR fluid in the channel. The Bypass MR damper (BMRD) contains a rectangular bypass flow channel, current controlled movable piston shaft arrangement and MR fluid. The static piston coil case is winding by a coil which is used inside the piston head arrangement. The current controlled coil case provides a magnetic flux through the BMRD cylinder for controllability. The high strength of alloy steel materials are used for making piston shaft which allows magnetic flux propagation throughout the BMRD cylinder. Using the above design materials, a Bypass MR damper is designed and tested. An excitation of current is applied during the experiment which characterizes the BMRD controllability. It is shown that the BMRD with external flow channel allows a high controllable damping force using an excitation current. The experimental result of damping force-displacement characteristics with current excitation and without current excitation are compared in this research. The BMRD model is validated by the experimental result at various frequencies and applied excitation current.

Tyre tread-block friction: modelling, simulation and experimental validation

Science.gov (United States)

Wallaschek, Jörg; Wies, Burkard

2013-07-01

Pneumatic tyres are used in vehicles since the beginning of the last century. They generate braking and steering forces for bicycles, motor cycles, cars, busses, trucks, agricultural vehicles and aircraft. These forces are generated in the usually very small contact area between tyre and road and their performance characteristics are of eminent importance for safety and comfort. Much research has been addressed to optimise tyre design with respect to footprint pressure and friction. In this context, the development of virtual tyre prototypes, that is, simulation models for the tyre, has grown to a science in its own. While the modelling of the structural dynamics of the tyre has reached a very advanced level, which allows to take into account effects like the rate-independent inelasticity of filled elastomers or the transient 3D deformations of the ply-reinforced tread, shoulder and sidewalls, little is known about the friction between tread-block elements and road. This is particularly obvious in the case when snow, ice, water or a third-body layer are present in the tyre-road contact. In the present paper, we give a survey on the present state of knowledge in the modelling, simulation and experimental validation of tyre tread-block friction processes. We concentrate on experimental techniques.

Optimal Design and Model Validation for Combustion Experiments in a Shock Tube

KAUST Repository

Long, Quan

2014-01-06

We develop a Bayesian framework for the optimal experimental design of the shock tube experiments which are being carried out at the KAUST Clean Combustion Center. The unknown parameters are the pre-exponential parameters and the activation energies in the reaction rate functions. The control parameters are the initial hydrogen concentration and the temperature. First, we build a polynomial based surrogate model for the observable related to the reactions in the shock tube. Second, we use a novel MAP based approach to estimate the expected information gain in the proposed experiments and select the best experimental set-ups corresponding to the optimal expected information gains. Third, we use the synthetic data to carry out virtual validation of our methodology.

Experimental validation of a thermodynamic boiler model under steady state and dynamic conditions

International Nuclear Information System (INIS)

Carlon, Elisa; Verma, Vijay Kumar; Schwarz, Markus; Golicza, Laszlo; Prada, Alessandro; Baratieri, Marco; Haslinger, Walter; Schmidl, Christoph

2015-01-01

Highlights: • Laboratory tests on two commercially available pellet boilers. • Steady state and a dynamic load cycle tests. • Pellet boiler model calibration based on data registered in stationary operation. • Boiler model validation with reference to both stationary and dynamic operation. • Validated model suitable for coupled simulation of building and heating system. - Abstract: Nowadays dynamic building simulation is an essential tool for the design of heating systems for residential buildings. The simulation of buildings heated by biomass systems, first of all needs detailed boiler models, capable of simulating the boiler both as a stand-alone appliance and as a system component. This paper presents the calibration and validation of a boiler model by means of laboratory tests. The chosen model, i.e. TRNSYS “Type 869”, has been validated for two commercially available pellet boilers of 6 and 12 kW nominal capacities. Two test methods have been applied: the first is a steady state test at nominal load and the second is a load cycle test including stationary operation at different loads as well as transient operation. The load cycle test is representative of the boiler operation in the field and characterises the boiler’s stationary and dynamic behaviour. The model had been calibrated based on laboratory data registered during stationary operation at different loads and afterwards it was validated by simulating both the stationary and the dynamic tests. Selected parameters for the validation were the heat transfer rates to water and the water temperature profiles inside the boiler and at the boiler outlet. Modelling results showed better agreement with experimental data during stationary operation rather than during dynamic operation. Heat transfer rates to water were predicted with a maximum deviation of 10% during the stationary operation, and a maximum deviation of 30% during the dynamic load cycle. However, for both operational regimes the

Automatic control system generation for robot design validation

Science.gov (United States)

Bacon, James A. (Inventor); English, James D. (Inventor)

2012-01-01

The specification and drawings present a new method, system and software product for and apparatus for generating a robotic validation system for a robot design. The robotic validation system for the robot design of a robotic system is automatically generated by converting a robot design into a generic robotic description using a predetermined format, then generating a control system from the generic robotic description and finally updating robot design parameters of the robotic system with an analysis tool using both the generic robot description and the control system.

Design and validation of a CT-guided robotic system for lung cancer brachytherapy.

Science.gov (United States)

Dou, Huaisu; Jiang, Shan; Yang, Zhiyong; Sun, Luqing; Ma, Xiaodong; Huo, Bin

2017-09-01

Currently, lung brachytherapy in clinical setting is a complex procedure. Operation accuracy depends on accurate positioning of the template; however, it is difficult to guarantee the positioning accuracy manually. Application of robotic-assisted systems can simplify the procedure and improve the manual positioning accuracy. Therefore, a novel CT-guided robotic system was developed to assist the lung cancer brachytherapy. A four degree-of-freedom (DOF) robot, controlled by a lung brachytherapy treatment planning system (TPS) software, was designed and manufactured to assist the template positioning. Target position of the template can be obtained from the treatment plan, thus the robot is driven to the target position automatically. The robotic system was validated in both the laboratory and the CT environment. In laboratory environment, a 3D laser tracker and an inertial measurement unit (IMU) were used to measure the mechanical accuracy in air, which includes positioning accuracy and position repeatability. Working reliability was also validated in this procedure by observing the response reliability and calculating the position repeatability. Imaging artifacts and accuracy of the robot registration were validated in the CT environment by using an artificial phantom with fiducial markers. CT images were obtained and used to test the image artifact and calculate the registration accuracy. Phantom experiments were conducted to test the accuracy of needle insertion by using a transparent hydrogel phantom with a high imitation artificial phantom. Also, the efficiency was validated in this procedure by comparing time costs in manual positioning with robotic positioning under the same experimental conditions. The robotic system achieved the positioning accuracy of 0.28 ± 0.25 mm and the position repeatability of 0.09 ± 0.11 mm. Experimental results showed that the robot was CT-compatible and responded reliably to the control commands. The mean registration accuracy

Validation and Design Science Research in Information Systems

NARCIS (Netherlands)

Sol, H G; Gonzalez, Rafael A.; Mora, Manuel

2012-01-01

Validation within design science research in Information Systems (DSRIS) is much debated. The relationship of validation to artifact evaluation is still not clear. This chapter aims at elucidating several components of DSRIS in relation to validation. The role of theory and theorizing are an

Servo-hydraulic actuator in controllable canonical form: Identification and experimental validation

Science.gov (United States)

Maghareh, Amin; Silva, Christian E.; Dyke, Shirley J.

2018-02-01

Hydraulic actuators have been widely used to experimentally examine structural behavior at multiple scales. Real-time hybrid simulation (RTHS) is one innovative testing method that largely relies on such servo-hydraulic actuators. In RTHS, interface conditions must be enforced in real time, and controllers are often used to achieve tracking of the desired displacements. Thus, neglecting the dynamics of hydraulic transfer system may result either in system instability or sub-optimal performance. Herein, we propose a nonlinear dynamical model for a servo-hydraulic actuator (a.k.a. hydraulic transfer system) coupled with a nonlinear physical specimen. The nonlinear dynamical model is transformed into controllable canonical form for further tracking control design purposes. Through a number of experiments, the controllable canonical model is validated.

Experimental validation of the containment codes ASTARTE and SEURBNUK

International Nuclear Information System (INIS)

Kendall, K.C.; Arnold, L.A.; Broadhouse, B.J.; Jones, A.; Yerkess, A.; Benuzzi, A.

1979-10-01

The fast reactor containment codes ASTARTE and SEURBNUK are being validated against data from the COVA series of small scale experiments being performed jointly by the UKAEA and JRC Ispra. The experimental programme is nearly complete, and data are given. (U.K.)

Experimental validation of calculated atomic charges in ionic liquids

Science.gov (United States)

Fogarty, Richard M.; Matthews, Richard P.; Ashworth, Claire R.; Brandt-Talbot, Agnieszka; Palgrave, Robert G.; Bourne, Richard A.; Vander Hoogerstraete, Tom; Hunt, Patricia A.; Lovelock, Kevin R. J.

2018-05-01

A combination of X-ray photoelectron spectroscopy and near edge X-ray absorption fine structure spectroscopy has been used to provide an experimental measure of nitrogen atomic charges in nine ionic liquids (ILs). These experimental results are used to validate charges calculated with three computational methods: charges from electrostatic potentials using a grid-based method (ChelpG), natural bond orbital population analysis, and the atoms in molecules approach. By combining these results with those from a previous study on sulfur, we find that ChelpG charges provide the best description of the charge distribution in ILs. However, we find that ChelpG charges can lead to significant conformational dependence and therefore advise that small differences in ChelpG charges (<0.3 e) should be interpreted with care. We use these validated charges to provide physical insight into nitrogen atomic charges for the ILs probed.

DMFC performance and methanol cross-over: Experimental analysis and model validation

Energy Technology Data Exchange (ETDEWEB)

Casalegno, A.; Marchesi, R. [Dipartimento di Energia, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milano (Italy)

2008-10-15

A combined experimental and modelling approach is proposed to analyze methanol cross-over and its effect on DMFC performance. The experimental analysis is performed in order to allow an accurate investigation of methanol cross-over influence on DMFC performance, hence measurements were characterized in terms of uncertainty and reproducibility. The findings suggest that methanol cross-over is mainly determined by diffusion transport and affects cell performance partly via methanol electro-oxidation at the cathode. The modelling analysis is carried out to further investigate methanol cross-over phenomenon. A simple model evaluates the effectiveness of two proposed interpretations regarding methanol cross-over and its effects. The model is validated using the experimental data gathered. Both the experimental analysis and the proposed and validated model allow a substantial step forward in the understanding of the main phenomena associated with methanol cross-over. The findings confirm the possibility to reduce methanol cross-over by optimizing anode feeding. (author)

The role of experimental typography in designing logotypes

OpenAIRE

Pogačnik, Tadeja

2014-01-01

Designing logotypes is an important part of graphic design. Great logotypes are designed using custom made typefaces. Therefore, it is very important, especially for the typographic designer, to have practical experience and be up to date with all trends in the field of experimental typefaces design, also called experimental typography. In my thesis statement, I carefully examined the problems of experimental typography - which allows more creative and free typography designing for different ...

Experimental design in chemistry: A tutorial.

Science.gov (United States)

Leardi, Riccardo

2009-10-12

In this tutorial the main concepts and applications of experimental design in chemistry will be explained. Unfortunately, nowadays experimental design is not as known and applied as it should be, and many papers can be found in which the "optimization" of a procedure is performed one variable at a time. Goal of this paper is to show the real advantages in terms of reduced experimental effort and of increased quality of information that can be obtained if this approach is followed. To do that, three real examples will be shown. Rather than on the mathematical aspects, this paper will focus on the mental attitude required by experimental design. The readers being interested to deepen their knowledge of the mathematical and algorithmical part can find very good books and tutorials in the references [G.E.P. Box, W.G. Hunter, J.S. Hunter, Statistics for Experimenters: An Introduction to Design, Data Analysis, and Model Building, John Wiley & Sons, New York, 1978; R. Brereton, Chemometrics: Data Analysis for the Laboratory and Chemical Plant, John Wiley & Sons, New York, 1978; R. Carlson, J.E. Carlson, Design and Optimization in Organic Synthesis: Second Revised and Enlarged Edition, in: Data Handling in Science and Technology, vol. 24, Elsevier, Amsterdam, 2005; J.A. Cornell, Experiments with Mixtures: Designs, Models and the Analysis of Mixture Data, in: Series in Probability and Statistics, John Wiley & Sons, New York, 1991; R.E. Bruns, I.S. Scarminio, B. de Barros Neto, Statistical Design-Chemometrics, in: Data Handling in Science and Technology, vol. 25, Elsevier, Amsterdam, 2006; D.C. Montgomery, Design and Analysis of Experiments, 7th edition, John Wiley & Sons, Inc., 2009; T. Lundstedt, E. Seifert, L. Abramo, B. Thelin, A. Nyström, J. Pettersen, R. Bergman, Chemolab 42 (1998) 3; Y. Vander Heyden, LC-GC Europe 19 (9) (2006) 469].

Experimental design of a waste glass study

International Nuclear Information System (INIS)

Piepel, G.F.; Redgate, P.E.; Hrma, P.

1995-04-01

A Composition Variation Study (CVS) is being performed to support a future high-level waste glass plant at Hanford. A total of 147 glasses, covering a broad region of compositions melting at approximately 1150 degrees C, were tested in five statistically designed experimental phases. This paper focuses on the goals, strategies, and techniques used in designing the five phases. The overall strategy was to investigate glass compositions on the boundary and interior of an experimental region defined by single- component, multiple-component, and property constraints. Statistical optimal experimental design techniques were used to cover various subregions of the experimental region in each phase. Empirical mixture models for glass properties (as functions of glass composition) from previous phases wee used in designing subsequent CVS phases

Criteria of the validation of experimental and evaluated covariance data

International Nuclear Information System (INIS)

Badikov, S.

2008-01-01

The criteria of the validation of experimental and evaluated covariance data are reviewed. In particular: a) the criterion of the positive definiteness for covariance matrices, b) the relationship between the 'integral' experimental and estimated uncertainties, c) the validity of the statistical invariants, d) the restrictions imposed to correlations between experimental errors, are described. Applying these criteria in nuclear data evaluation was considered and 4 particular points have been examined. First preserving positive definiteness of covariance matrices in case of arbitrary transformation of a random vector was considered, properties of the covariance matrices in operations widely used in neutron and reactor physics (splitting and collapsing energy groups, averaging the physical values over energy groups, estimation parameters on the basis of measurements by means of generalized least squares method) were studied. Secondly, an algorithm for comparison of experimental and estimated 'integral' uncertainties was developed, square root of determinant of a covariance matrix is recommended for use in nuclear data evaluation as a measure of 'integral' uncertainty for vectors of experimental and estimated values. Thirdly, a set of statistical invariants-values which are preserved in statistical processing was presented. And fourthly, the inequality that signals a correlation between experimental errors that leads to unphysical values is given. An application is given concerning the cross-section of the (n,t) reaction on Li 6 with a neutron incident energy comprised between 1 and 100 keV

Experimental validation of a mathematical model for seabed liquefaction in waves

DEFF Research Database (Denmark)

Sumer, B. Mutlu; Kirca, Özgür; Fredsøe, Jørgen

2011-01-01

This paper summarizes the results of an experimental study directed towards the validation of a mathematical model for the buildup of pore water pressure and resulting liquefaction of marine soils under progressive waves. Experiments were conducted under controlled conditions with silt ( d50 = 0.......070 mm) in a wave flume with a soil pit. Waves with wave heights in the range 7.7-18 cm with the water depth 55 cm and the wave period 1.6 s enabled us to study both the liquefaction and no-liquefaction regime pore water pressure buildup. The experimental data was used to validate the model. A numerical...

Multi-objective experimental design for (13)C-based metabolic flux analysis.

Science.gov (United States)

Bouvin, Jeroen; Cajot, Simon; D'Huys, Pieter-Jan; Ampofo-Asiama, Jerry; Anné, Jozef; Van Impe, Jan; Geeraerd, Annemie; Bernaerts, Kristel

2015-10-01

(13)C-based metabolic flux analysis is an excellent technique to resolve fluxes in the central carbon metabolism but costs can be significant when using specialized tracers. This work presents a framework for cost-effective design of (13)C-tracer experiments, illustrated on two different networks. Linear and non-linear optimal input mixtures are computed for networks for Streptomyces lividans and a carcinoma cell line. If only glucose tracers are considered as labeled substrate for a carcinoma cell line or S. lividans, the best parameter estimation accuracy is obtained by mixtures containing high amounts of 1,2-(13)C2 glucose combined with uniformly labeled glucose. Experimental designs are evaluated based on a linear (D-criterion) and non-linear approach (S-criterion). Both approaches generate almost the same input mixture, however, the linear approach is favored due to its low computational effort. The high amount of 1,2-(13)C2 glucose in the optimal designs coincides with a high experimental cost, which is further enhanced when labeling is introduced in glutamine and aspartate tracers. Multi-objective optimization gives the possibility to assess experimental quality and cost at the same time and can reveal excellent compromise experiments. For example, the combination of 100% 1,2-(13)C2 glucose with 100% position one labeled glutamine and the combination of 100% 1,2-(13)C2 glucose with 100% uniformly labeled glutamine perform equally well for the carcinoma cell line, but the first mixture offers a decrease in cost of $ 120 per ml-scale cell culture experiment. We demonstrated the validity of a multi-objective linear approach to perform optimal experimental designs for the non-linear problem of (13)C-metabolic flux analysis. Tools and a workflow are provided to perform multi-objective design. The effortless calculation of the D-criterion can be exploited to perform high-throughput screening of possible (13)C-tracers, while the illustrated benefit of multi

Chemicals-Based Formulation Design: Virtual Experimentations

DEFF Research Database (Denmark)

Conte, Elisa; Gani, Rafiqul

2011-01-01

This paper presents a systematic procedure for virtual experimentations related to the design of liquid formulated products. All the experiments that need to be performed when designing a liquid formulated product (lotion), such as ingredients selection and testing, solubility tests, property mea...... on the design of an insect repellent lotion will show that the software is an essential instrument in decision making, and that it reduces time and resources since experimental efforts can be focused on one or few product alternatives....

Experimental Validation of Flow Force Models for Fast Switching Valves

DEFF Research Database (Denmark)

Bender, Niels Christian; Pedersen, Henrik Clemmensen; Nørgård, Christian

2017-01-01

This paper comprises a detailed study of the forces acting on a Fast Switching Valve (FSV) plunger. The objective is to investigate to what extend different models are valid to be used for design purposes. These models depend on the geometry of the moving plunger and the properties of the surroun......This paper comprises a detailed study of the forces acting on a Fast Switching Valve (FSV) plunger. The objective is to investigate to what extend different models are valid to be used for design purposes. These models depend on the geometry of the moving plunger and the properties...... to compare and validate different models, where an effort is directed towards capturing the fluid squeeze effect just before material on material contact. The test data is compared with simulation data relying solely on analytic formulations. The general dynamics of the plunger is validated...

A validation methodology for fault-tolerant clock synchronization

Science.gov (United States)

Johnson, S. C.; Butler, R. W.

1984-01-01

A validation method for the synchronization subsystem of a fault-tolerant computer system is presented. The high reliability requirement of flight crucial systems precludes the use of most traditional validation methods. The method presented utilizes formal design proof to uncover design and coding errors and experimentation to validate the assumptions of the design proof. The experimental method is described and illustrated by validating an experimental implementation of the Software Implemented Fault Tolerance (SIFT) clock synchronization algorithm. The design proof of the algorithm defines the maximum skew between any two nonfaulty clocks in the system in terms of theoretical upper bounds on certain system parameters. The quantile to which each parameter must be estimated is determined by a combinatorial analysis of the system reliability. The parameters are measured by direct and indirect means, and upper bounds are estimated. A nonparametric method based on an asymptotic property of the tail of a distribution is used to estimate the upper bound of a critical system parameter. Although the proof process is very costly, it is extremely valuable when validating the crucial synchronization subsystem.

Validation of experimental molecular crystal structures with dispersion-corrected density functional theory calculations

International Nuclear Information System (INIS)

Streek, Jacco van de; Neumann, Marcus A.

2010-01-01

The accuracy of a dispersion-corrected density functional theory method is validated against 241 experimental organic crystal structures from Acta Cryst. Section E. This paper describes the validation of a dispersion-corrected density functional theory (d-DFT) method for the purpose of assessing the correctness of experimental organic crystal structures and enhancing the information content of purely experimental data. 241 experimental organic crystal structures from the August 2008 issue of Acta Cryst. Section E were energy-minimized in full, including unit-cell parameters. The differences between the experimental and the minimized crystal structures were subjected to statistical analysis. The r.m.s. Cartesian displacement excluding H atoms upon energy minimization with flexible unit-cell parameters is selected as a pertinent indicator of the correctness of a crystal structure. All 241 experimental crystal structures are reproduced very well: the average r.m.s. Cartesian displacement for the 241 crystal structures, including 16 disordered structures, is only 0.095 Å (0.084 Å for the 225 ordered structures). R.m.s. Cartesian displacements above 0.25 Å either indicate incorrect experimental crystal structures or reveal interesting structural features such as exceptionally large temperature effects, incorrectly modelled disorder or symmetry breaking H atoms. After validation, the method is applied to nine examples that are known to be ambiguous or subtly incorrect

Experimental design and estimation of growth rate distributions in size-structured shrimp populations

International Nuclear Information System (INIS)

Banks, H T; Davis, Jimena L; Ernstberger, Stacey L; Hu, Shuhua; Artimovich, Elena; Dhar, Arun K

2009-01-01

We discuss inverse problem results for problems involving the estimation of probability distributions using aggregate data for growth in populations. We begin with a mathematical model describing variability in the early growth process of size-structured shrimp populations and discuss a computational methodology for the design of experiments to validate the model and estimate the growth-rate distributions in shrimp populations. Parameter-estimation findings using experimental data from experiments so designed for shrimp populations cultivated at Advanced BioNutrition Corporation are presented, illustrating the usefulness of mathematical and statistical modeling in understanding the uncertainty in the growth dynamics of such populations

Development and validation of a radial turbine efficiency and mass flow model at design and off-design conditions

International Nuclear Information System (INIS)

Serrano, José Ramón; Arnau, Francisco José; García-Cuevas, Luis Miguel; Dombrovsky, Artem; Tartoussi, Hadi

2016-01-01

Highlights: • A procedure for performance maps extrapolation of any radial turbine is presented. • Non measured VGT positions, speeds and blade to jet speed ratios can be extrapolated. • Calibration coefficients that can be fitted with a limited set of map data are used. • Experimental points at high blade to jet speed ratios have been used for validation. • The extrapolation accuracy is good in different map ranges and variables. - Abstract: Turbine performance at extreme off-design conditions is growing in importance for properly computing turbocharged reciprocating internal combustion engines behaviour during urban driving conditions at current and future homologation cycles. In these cases, the turbine operates at very low flow rates and power outputs and at very high blade to jet speed ratios during transitory periods due to turbocharger wheel inertia and the high pulsation level of engine exhaust flow. This paper presents a physically based method that is able to extrapolate radial turbines reduced mass flow and adiabatic efficiency in blade speed ratio, turbine rotational speed and stator vanes position. The model uses a very narrow range of experimental data from turbine maps to fit the necessary coefficients. By using a special experimental turbocharger gas stand, experimental data have been obtained for extremely low turbine power outputs for the sake of model validation. Even if the data used for fitting only covers the turbine normal operation zone, the extrapolation model provides very good agreement with the experiments at very high blade speed ratio points; producing also good results when extrapolating in rotational speed and stator vanes position.

Waste Isolation Pilot Plant design validation: Final report

International Nuclear Information System (INIS)

1986-10-01

This report provides documentation of actual underground conditions encountered as they relate to the design criteria, design bases, and design configurations for the reference design of the underground openings. It includes a selection of the more essential data collected during the design validation effort and an interpretation of these data

Experimental and simulation validation of ABHE for disinfection of Legionella in hot water systems

International Nuclear Information System (INIS)

Altorkmany, Lobna; Kharseh, Mohamad; Ljung, Anna-Lena; Staffan Lundström, T.

2017-01-01

Highlights: • ABHE system can supply a continues thermal treatment of water with saving energy. • Mathematical and experimental validation of ABHE performance are presented. • EES-based model is developed to simulate ABHE system. • Energy saving by ABHE is proved for different initial working parameters. - Abstract: The work refers to an innovative system inspired by nature that mimics the thermoregulation system that exists in animals. This method, which is called Anti Bacteria Heat Exchanger (ABHE), is proposed to achieve continuous thermal disinfection of bacteria in hot water systems with high energy efficiency. In particular, this study aims to demonstrate the opportunity to gain energy by means of recovering heat over a plate heat exchanger. Firstly, the thermodynamics of the ABHE is clarified to define the ABHE specification. Secondly, a first prototype of an ABHE is built with a specific configuration based on simplicity regarding design and construction. Thirdly, an experimental test is carried out. Finally, a computer model is built to simulate the ABHE system and the experimental data is used to validate the model. The experimental results indicate that the performance of the ABHE system is strongly dependent on the flow rate, while the supplied temperature has less effect. Experimental and simulation data show a large potential for saving energy of this thermal disinfection method by recovering heat. To exemplify, when supplying water at a flow rate of 5 kg/min and at a temperature of 50 °C, the heat recovery is about 1.5 kW while the required pumping power is 1 W. This means that the pressure drop is very small compared to the energy recovered and consequently high saving in total cost is promising.

Design validation and performance of closed loop gas recirculation system

International Nuclear Information System (INIS)

Kalmani, S.D.; Majumder, G.; Mondal, N.K.; Shinde, R.R.; Joshi, A.V.

2016-01-01

A pilot experimental set up of the India Based Neutrino Observatory's ICAL detector has been operational for the last 4 years at TIFR, Mumbai. Twelve glass RPC detectors of size 2 × 2 m 2 , with a gas gap of 2 mm are under test in a closed loop gas recirculation system. These RPCs are continuously purged individually, with a gas mixture of R134a (C 2 H 2 F 4 ), isobutane (iC 4 H 10 ) and sulphur hexafluoride (SF 6 ) at a steady rate of 360 ml/h to maintain about one volume change a day. To economize gas mixture consumption and to reduce the effluents from being released into the atmosphere, a closed loop system has been designed, fabricated and installed at TIFR. The pressure and flow rate in the loop is controlled by mass flow controllers and pressure transmitters. The performance and integrity of RPCs in the pilot experimental set up is being monitored to assess the effect of periodic fluctuation and transients in atmospheric pressure and temperature, room pressure variation, flow pulsations, uniformity of gas distribution and power failures. The capability of closed loop gas recirculation system to respond to these changes is also studied. The conclusions from the above experiment are presented. The validations of the first design considerations and subsequent modifications have provided improved guidelines for the future design of the engineering module gas system.

Experimental validation of 3D printed material behaviors and their influence on the structural topology design

Science.gov (United States)

Yang, Kai Ke; Zhu, Ji Hong; Wang, Chuang; Jia, Dong Sheng; Song, Long Long; Zhang, Wei Hong

2018-05-01

The purpose of this paper is to investigate the structures achieved by topology optimization and their fabrications by 3D printing considering the particular features of material microstructures and macro mechanical performances. Combining Digital Image Correlation and Optical Microscope, this paper experimentally explored the anisotropies of stiffness and strength existing in the 3D printed polymer material using Stereolithography (SLA) and titanium material using Selective Laser Melting (SLM). The standard specimens and typical structures obtained by topology optimization were fabricated along different building directions. On the one hand, the experimental results of these SLA produced structures showed stable properties and obviously anisotropic rules in stiffness, ultimate strengths and places of fractures. Further structural designs were performed using topology optimization when the particular mechanical behaviors of SLA printed materials were considered, which resulted in better structural performances compared to the optimized designs using `ideal' isotropic material model. On the other hand, this paper tested the mechanical behaviors of SLM printed multiscale lattice structures which were fabricated using the same metal powder and the same machine. The structural stiffness values are generally similar while the strength behaviors show a difference, which are mainly due to the irregular surface quality of the tiny structural branches of the lattice. The above evidences clearly show that the consideration of the particular behaviors of 3D printed materials is therefore indispensable for structural design and optimization in order to improve the structural performance and strengthen their practical significance.

Experimental validation of 3D printed material behaviors and their influence on the structural topology design

Science.gov (United States)

Yang, Kai Ke; Zhu, Ji Hong; Wang, Chuang; Jia, Dong Sheng; Song, Long Long; Zhang, Wei Hong

2018-02-01

The purpose of this paper is to investigate the structures achieved by topology optimization and their fabrications by 3D printing considering the particular features of material microstructures and macro mechanical performances. Combining Digital Image Correlation and Optical Microscope, this paper experimentally explored the anisotropies of stiffness and strength existing in the 3D printed polymer material using Stereolithography (SLA) and titanium material using Selective Laser Melting (SLM). The standard specimens and typical structures obtained by topology optimization were fabricated along different building directions. On the one hand, the experimental results of these SLA produced structures showed stable properties and obviously anisotropic rules in stiffness, ultimate strengths and places of fractures. Further structural designs were performed using topology optimization when the particular mechanical behaviors of SLA printed materials were considered, which resulted in better structural performances compared to the optimized designs using `ideal' isotropic material model. On the other hand, this paper tested the mechanical behaviors of SLM printed multiscale lattice structures which were fabricated using the same metal powder and the same machine. The structural stiffness values are generally similar while the strength behaviors show a difference, which are mainly due to the irregular surface quality of the tiny structural branches of the lattice. The above evidences clearly show that the consideration of the particular behaviors of 3D printed materials is therefore indispensable for structural design and optimization in order to improve the structural performance and strengthen their practical significance.

Validation of NEPTUNE-CFD two-phase flow models using experimental data

International Nuclear Information System (INIS)

Perez-Manes, Jorge; Sanchez Espinoza, Victor Hugo; Bottcher, Michael; Stieglitz, Robert; Sergio Chiva Vicent

2014-01-01

This paper deals with the validation of the two-phase flow models of the CFD code NEPTUNE-CFD using experimental data provided by the OECD BWR BFBT and PSBT Benchmark. Since the two-phase models of CFD codes are extensively being improved, the validation is a key step for the acceptability of such codes. The validation work is performed in the frame of the European NURISP Project and it was focused on the steady state and transient void fraction tests. The influence of different NEPTUNE-CFD model parameters on the void fraction prediction is investigated and discussed in detail. Due to the coupling of heat conduction solver SYRTHES with NEPTUNE-CFD, the description of the coupled fluid dynamics and heat transfer between the fuel rod and the fluid is improved significantly. The averaged void fraction predicted by NEPTUNE-CFD for selected PSBT and BFBT tests is in good agreement with the experimental data. Finally, areas for future improvements of the NEPTUNE-CFD code were identified, too. (authors)

Present activities for the preparation of a Japanese draft of structural design guidelines for the experimental fusion reactor

International Nuclear Information System (INIS)

Miya, K.; Muto, Y.; Takatsu, H.; Hada, K.; Koizumi, K.; Jitsukawa, S.; Arai, T.; Ohkawa, Y.; Shimakawa, T.; Aoto, K.; Shiraishi, H.; Takagi, T.; Miki, N.; Takahashi, S.; Sato, K.; Takemasa, F.; Kasaba, M.; Kudough, F.; Fujita, J.; Kajiura, S.; Kinoshita, S.

1996-01-01

Since November 1990, systematic research has been carried out in preparation for a Japanese draft of structural design guidelines for the experimental fusion reactor. This report summarizes the major results of the work and the status of these efforts. A classification of components and definition of operating conditions are proposed on the basis of the ITER-CDA design, in the light of the safety characteristics of the fusion reactor and relevant conventions for the existing fission reactor design code. Specific issues regarding the structural design of the experimental fusion reactor are discussed based on the experimental and analytical work. The validity of the existing structural design method is confirmed for the use of irradiated 316 SS, irrespective of the significant reduction in uniform elongation capability caused by heavy neutron irradiation. Further important phenomena are treated such as magnetic damping, magnetic stiffness and fracture due to electromagnetic forces. Finally, the issues concerned with welding and non-destructive examinations are discussed with relevance to component classification. (orig.)

Design, Manufacturing and Experimental Validation of Optical Fiber Sensors Based Devices for Structural Health Monitoring

Directory of Open Access Journals (Sweden)

Angela CORICCIATI

2016-06-01

Full Text Available The use of optical fiber sensors is a promising and rising technique used for Structural Health Monitoring (SHM, because permit to monitor continuously the strain and the temperature of the structure where they are applied. In the present paper three different types of smart devices, that are composite materials with an optical fiber sensor embedded inside them during the manufacturing process, are described: Smart Patch, Smart Rebar and Smart Textile, which are respectively a plate for local exterior intervention, a rod for shear and flexural interior reinforcement and a textile for an external whole application. In addition to the monitoring aim, the possible additional function of these devices could be the reinforcement of the structures where they are applied. In the present work, after technology manufacturing description, the experimental laboratory characterization of each device is discussed. At last, smart devices application on medium scale masonry walls and their validation by mechanical tests is described.

Experimental Definition and Validation of Protein Coding Transcripts in Chlamydomonas reinhardtii

Energy Technology Data Exchange (ETDEWEB)

Kourosh Salehi-Ashtiani; Jason A. Papin

2012-01-13

Algal fuel sources promise unsurpassed yields in a carbon neutral manner that minimizes resource competition between agriculture and fuel crops. Many challenges must be addressed before algal biofuels can be accepted as a component of the fossil fuel replacement strategy. One significant challenge is that the cost of algal fuel production must become competitive with existing fuel alternatives. Algal biofuel production presents the opportunity to fine-tune microbial metabolic machinery for an optimal blend of biomass constituents and desired fuel molecules. Genome-scale model-driven algal metabolic design promises to facilitate both goals by directing the utilization of metabolites in the complex, interconnected metabolic networks to optimize production of the compounds of interest. Using Chlamydomonas reinhardtii as a model, we developed a systems-level methodology bridging metabolic network reconstruction with annotation and experimental verification of enzyme encoding open reading frames. We reconstructed a genome-scale metabolic network for this alga and devised a novel light-modeling approach that enables quantitative growth prediction for a given light source, resolving wavelength and photon flux. We experimentally verified transcripts accounted for in the network and physiologically validated model function through simulation and generation of new experimental growth data, providing high confidence in network contents and predictive applications. The network offers insight into algal metabolism and potential for genetic engineering and efficient light source design, a pioneering resource for studying light-driven metabolism and quantitative systems biology. Our approach to generate a predictive metabolic model integrated with cloned open reading frames, provides a cost-effective platform to generate metabolic engineering resources. While the generated resources are specific to algal systems, the approach that we have developed is not specific to algae and

Experimental Design: Review and Comment.

Science.gov (United States)

1984-02-01

creativity. Innovative modifications and extensions of classical experimental designs were developed and many useful articles were published in a short...Pjrazolone Industrielle ," Bulletin de la Soci~t6 Chimique de France, 11-12, 1171-1174. LI, K. C. (1983), "Minimaxity for Randomized Designs: Some

Zero-G experimental validation of a robotics-based inertia identification algorithm

Science.gov (United States)

Bruggemann, Jeremy J.; Ferrel, Ivann; Martinez, Gerardo; Xie, Pu; Ma, Ou

2010-04-01

The need to efficiently identify the changing inertial properties of on-orbit spacecraft is becoming more critical as satellite on-orbit services, such as refueling and repairing, become increasingly aggressive and complex. This need stems from the fact that a spacecraft's control system relies on the knowledge of the spacecraft's inertia parameters. However, the inertia parameters may change during flight for reasons such as fuel usage, payload deployment or retrieval, and docking/capturing operations. New Mexico State University's Dynamics, Controls, and Robotics Research Group has proposed a robotics-based method of identifying unknown spacecraft inertia properties1. Previous methods require firing known thrusts then measuring the thrust, and the velocity and acceleration changes. The new method utilizes the concept of momentum conservation, while employing a robotic device powered by renewable energy to excite the state of the satellite. Thus, it requires no fuel usage or force and acceleration measurements. The method has been well studied in theory and demonstrated by simulation. However its experimental validation is challenging because a 6- degree-of-freedom motion in a zero-gravity condition is required. This paper presents an on-going effort to test the inertia identification method onboard the NASA zero-G aircraft. The design and capability of the test unit will be discussed in addition to the flight data. This paper also introduces the design and development of an airbearing based test used to partially validate the method, in addition to the approach used to obtain reference value for the test system's inertia parameters that can be used for comparison with the algorithm results.

Experimental on-line platform for product conceptual design: OpenDesigNet

Directory of Open Access Journals (Sweden)

Teresa Magal-Royo

2013-09-01

Full Text Available This paper highlights the need for using specialised on-line collaborative environments by designers and product engineers who increasingly use Web 2.0 technology to search for information. Although there are professional channels and networks, there is no specific platform which helps during a new product’s conceptualisation phase. Open communication must thus be promoted and encouraged amongst design professionals and companies to form working groups thereby allowing them to work collaboratively in the most open and creative phase of product design, i.e. conceptualisation. The OpenDesigNet (ODN experimental platform has been developed so that designers and small- or medium-sized companies (SMC can access on-line collaborative tools to support the creation and promotion of new on-line products and assess their immediate social impact. This article presents some of the results obtained during the validation phase involving a platform satisfaction survey of design engineering students and has led to a first-hand assessment of the new platform’s potential impact on their professional future.

Design, construction and validation of a Plasmodium vivax microarray for the transcriptome profiling of clinical isolates

KAUST Repository

Boopathi, Pon Arunachalam

2016-10-09

High density oligonucleotide microarrays have been used on Plasmodium vivax field isolates to estimate whole genome expression. However, no microarray platform has been experimentally optimized for studying the transcriptome of field isolates. In the present study, we adopted both bioinformatics and experimental testing approaches to select best optimized probes suitable for detecting parasite transcripts from field samples and included them in designing a custom 15K P. vivax microarray. This microarray has long oligonucleotide probes (60 mer) that were in-situ synthesized onto glass slides using Agilent SurePrint technology and has been developed into an 8X15K format (8 identical arrays on a single slide). Probes in this array were experimentally validated and represents 4180 P. vivax genes in sense orientation, of which 1219 genes have also probes in antisense orientation. Validation of the 15K array by using field samples (n =14) has shown 99% of parasite transcript detection from any of the samples. Correlation analysis between duplicate probes (n = 85) present in the arrays showed perfect correlation (r(2) = 0.98) indicating the reproducibility. Multiple probes representing the same gene exhibited similar kind of expression pattern across the samples (positive correlation, r >= 0.6). Comparison of hybridization data with the previous studies and quantitative real-time PCR experiments were performed to highlight the microarray validation procedure. This array is unique in its design, and results indicate that the array is sensitive and reproducible. Hence, this microarray could be a valuable functional genomics tool to generate reliable expression data from P. vivax field isolates. (C) 2016 Published by Elsevier B.V.

Design, construction and validation of a Plasmodium vivax microarray for the transcriptome profiling of clinical isolates

KAUST Repository

Boopathi, Pon Arunachalam; Subudhi, Amit; Middha, Sheetal; Acharya, Jyoti; Mugasimangalam, Raja Chinnadurai; Kochar, Sanjay Kumar; Kochar, Dhanpat Kumar; Das, Ashis

2016-01-01

High density oligonucleotide microarrays have been used on Plasmodium vivax field isolates to estimate whole genome expression. However, no microarray platform has been experimentally optimized for studying the transcriptome of field isolates. In the present study, we adopted both bioinformatics and experimental testing approaches to select best optimized probes suitable for detecting parasite transcripts from field samples and included them in designing a custom 15K P. vivax microarray. This microarray has long oligonucleotide probes (60 mer) that were in-situ synthesized onto glass slides using Agilent SurePrint technology and has been developed into an 8X15K format (8 identical arrays on a single slide). Probes in this array were experimentally validated and represents 4180 P. vivax genes in sense orientation, of which 1219 genes have also probes in antisense orientation. Validation of the 15K array by using field samples (n =14) has shown 99% of parasite transcript detection from any of the samples. Correlation analysis between duplicate probes (n = 85) present in the arrays showed perfect correlation (r(2) = 0.98) indicating the reproducibility. Multiple probes representing the same gene exhibited similar kind of expression pattern across the samples (positive correlation, r >= 0.6). Comparison of hybridization data with the previous studies and quantitative real-time PCR experiments were performed to highlight the microarray validation procedure. This array is unique in its design, and results indicate that the array is sensitive and reproducible. Hence, this microarray could be a valuable functional genomics tool to generate reliable expression data from P. vivax field isolates. (C) 2016 Published by Elsevier B.V.

Optimal Bayesian Experimental Design for Combustion Kinetics

KAUST Repository

Huan, Xun

2011-01-04

Experimental diagnostics play an essential role in the development and refinement of chemical kinetic models, whether for the combustion of common complex hydrocarbons or of emerging alternative fuels. Questions of experimental design—e.g., which variables or species to interrogate, at what resolution and under what conditions—are extremely important in this context, particularly when experimental resources are limited. This paper attempts to answer such questions in a rigorous and systematic way. We propose a Bayesian framework for optimal experimental design with nonlinear simulation-based models. While the framework is broadly applicable, we use it to infer rate parameters in a combustion system with detailed kinetics. The framework introduces a utility function that reflects the expected information gain from a particular experiment. Straightforward evaluation (and maximization) of this utility function requires Monte Carlo sampling, which is infeasible with computationally intensive models. Instead, we construct a polynomial surrogate for the dependence of experimental observables on model parameters and design conditions, with the help of dimension-adaptive sparse quadrature. Results demonstrate the efficiency and accuracy of the surrogate, as well as the considerable effectiveness of the experimental design framework in choosing informative experimental conditions.

Analysis of progressive distorsion. Validation of the method based on effective primary stress. Discussion of Anderson's experimental data

International Nuclear Information System (INIS)

Moulin, Didier.

1981-02-01

An empirical rule usable for design by analysis against progressive distorsion has been set up from experiments conducted in C.E.N. Saclay. This rule is checked with experimental data obtained by W.F. ANDERSON, this experiment is sufficiently different from the Saclay one to evaluate the merits of the rule. The satisfactory results achieved, are another validation of the efficiency diagram on which the method is based [fr

Guided exploration of physically valid shapes for furniture design

KAUST Repository

Umetani, Nobuyuki; Igarashi, Takeo; Mitra, Niloy J.

2012-01-01

Geometric modeling and the physical validity of shapes are traditionally considered independently. This makes creating aesthetically pleasing yet physically valid models challenging. We propose an interactive design framework for efficient

Optimization of the representativeness and transposition approach, for the neutronic design of experimental programs in critical mock-up

International Nuclear Information System (INIS)

Dos-Santos, N.

2013-01-01

The work performed during this thesis focused on uncertainty propagation (nuclear data, technological uncertainties, calculation biases,...) on integral parameters, and the development of a novel approach enabling to reduce this uncertainty a priori directly from the design phase of a new experimental program. This approach is based on a multi-parameter multi-criteria extension of representativeness and transposition theories. The first part of this PhD work covers an optimization study of sensitivity and uncertainty calculation schemes to different modeling scales (cell, assembly and whole core) for LWRs and FBRs. A degraded scheme, based on standard and generalized perturbation theories, has been validated for the calculation of uncertainty propagation to various integral quantities of interest. It demonstrated the good a posteriori representativeness of the EPICURE experiment for the validation of mixed UOX-MOX loadings, as the importance of some nuclear data in the power tilt phenomenon in large LWR cores. The second part of this work was devoted to methods and tools development for the optimized design of experimental programs in ZPRs. Those methods are based on multi-parameters representativeness using simultaneously various quantities of interest. Finally, an original study has been conducted on the rigorous estimation of correlations between experimental programs in the transposition process. The coupling of experimental correlations and multi-parametric representativeness approach enables to efficiently design new programs, able to answer additional qualification requirements on calculation tools. (author) [fr

Modeling of surge in free-spool centrifugal compressors : experimental validation

NARCIS (Netherlands)

Gravdahl, J.T.; Willems, F.P.T.; Jager, de A.G.; Egeland, O.

2004-01-01

The derivation of a compressor characteristic, and the experimental validation of a dynamic model for a variable speed centrifugal compressor using this characteristic, are presented. The dynamic compressor model of Fink et al. is used, and a variable speed compressor characteristic is derived by

TU-H-BRA-07: Design, Construction, and Installation of An Experimental Beam Line for the Development of MRI-Linac Compatible Electron Accelerator

International Nuclear Information System (INIS)

Whelan, B; Keall, P; Holloway, L; Gierman, S; Schmerge, J; Tantawi, S; Tremaine, A; Trautwein, A; Scott, B; Fahrig, R

2016-01-01

Purpose: MRI guided radiation therapy (MRIgRT) is a rapidly growing field; however, Linac operation in MRI fringe fields represents an ongoing challenge. We have previously shown in-silico that Linacs could be redesigned to function in the in-line orientation with no magnetic shielding by adopting an RF-gun configuration. Other authors have also published insilico studies of Linac operation in magnetic fields; however to date no experimental validation data is published. This work details the design, construction, and installation of an experimental beam line to validate our in-silico results. Methods: An RF-gun comprising 1.5 accelerating cells and capable of generating electron energies up to 3.2MeV is used. The experimental apparatus was designed to monitor both beam current (toroid current monitor), spot size (two phosphor screens with viewports), and generate peak magnetic fields of at least 1000G (three variable current electromagnetic coils). Thermal FEM simulations were developed to ensure coil temperature remained within 100degC. Other design considerations included beam disposal, vacuum maintenance, radiation shielding, earthquake safety, and machine protection interlocks. Results: The beam line has been designed, built, and installed in a radiation shielded bunker. Water cooling, power supplies, thermo-couples, cameras, and radiation shielding have been successfully connected and tested. Interlock testing, vacuum processing, and RF processing have been successfully completed. The first beam on is expected within weeks. The coil heating simulations show that with care, peak fields of up to 1200G (320G at cathode) can be produced using 40A current, which is well within the fields expected for MRI-Linac systems. The maximum coil temperature at this current was 84degC after 6 minutes. Conclusion: An experimental beam line has been constructed and installed at SLAC in order to experimentally characterise RF gun performance in in-line magnetic fields, validate

TU-H-BRA-07: Design, Construction, and Installation of An Experimental Beam Line for the Development of MRI-Linac Compatible Electron Accelerator

Energy Technology Data Exchange (ETDEWEB)

Whelan, B; Keall, P [University of Sydney, Sydney (Australia); Holloway, L [Liverpool Hospital and Ingham Institute, Liverpool, NSW (United Kingdom); Gierman, S; Schmerge, J; Tantawi, S; Tremaine, A; Trautwein, A; Scott, B [Stanford Linear Accelerator Facility, Palo Alto, CA (United States); Fahrig, R [Siemens Healthcare GmbH, Forchheim (Germany)

2016-06-15

Purpose: MRI guided radiation therapy (MRIgRT) is a rapidly growing field; however, Linac operation in MRI fringe fields represents an ongoing challenge. We have previously shown in-silico that Linacs could be redesigned to function in the in-line orientation with no magnetic shielding by adopting an RF-gun configuration. Other authors have also published insilico studies of Linac operation in magnetic fields; however to date no experimental validation data is published. This work details the design, construction, and installation of an experimental beam line to validate our in-silico results. Methods: An RF-gun comprising 1.5 accelerating cells and capable of generating electron energies up to 3.2MeV is used. The experimental apparatus was designed to monitor both beam current (toroid current monitor), spot size (two phosphor screens with viewports), and generate peak magnetic fields of at least 1000G (three variable current electromagnetic coils). Thermal FEM simulations were developed to ensure coil temperature remained within 100degC. Other design considerations included beam disposal, vacuum maintenance, radiation shielding, earthquake safety, and machine protection interlocks. Results: The beam line has been designed, built, and installed in a radiation shielded bunker. Water cooling, power supplies, thermo-couples, cameras, and radiation shielding have been successfully connected and tested. Interlock testing, vacuum processing, and RF processing have been successfully completed. The first beam on is expected within weeks. The coil heating simulations show that with care, peak fields of up to 1200G (320G at cathode) can be produced using 40A current, which is well within the fields expected for MRI-Linac systems. The maximum coil temperature at this current was 84degC after 6 minutes. Conclusion: An experimental beam line has been constructed and installed at SLAC in order to experimentally characterise RF gun performance in in-line magnetic fields, validate

Rapid Computer Aided Ligand Design and Screening of Precious Metal Extractants from TRUEX Raffinate with Experimental Validation

International Nuclear Information System (INIS)

Clark, Aurora Sue; Wall, Nathalie; Benny, Paul

2015-01-01

design of a software program that uses state-of-the-art computational combinatorial chemistry, and is developed and validated with experimental data acquisition; the resulting tool allows for rapid design and screening of new ligands for the extraction of precious metals from SNF. This document describes the software that has been produced, ligands that have been designed, and fundamental new understandings of the extraction process of Rh(III) as a function of solution phase conditions (pH, nature of acid, etc.).

Rapid Computer Aided Ligand Design and Screening of Precious Metal Extractants from TRUEX Raffinate with Experimental Validation

Energy Technology Data Exchange (ETDEWEB)

Clark, Aurora Sue [Washington State Univ., Pullman, WA (United States); Wall, Nathalie [Washington State Univ., Pullman, WA (United States); Benny, Paul [Washington State Univ., Pullman, WA (United States)

2015-11-16

through the design of a software program that uses state-of-the-art computational combinatorial chemistry, and is developed and validated with experimental data acquisition; the resulting tool allows for rapid design and screening of new ligands for the extraction of precious metals from SNF. This document describes the software that has been produced, ligands that have been designed, and fundamental new understandings of the extraction process of Rh(III) as a function of solution phase conditions (pH, nature of acid, etc.).

Validation of Helium Inlet Design for ITER Toroidal Field Coil

CERN Document Server

Boyer, C; Hamada, K; Foussat, A; Le Rest, M; Mitchell, N; Decool, P; Savary, F; Sgobba, S; Weiss, K-P

2014-01-01

The ITER organization has performed design and its validation tests on a helium inlet structure for the ITER Toroidal Field (TF) coil under collaboration with CERN, KIT, and CEA-Cadarache. Detailed structural analysis was performed in order to optimize the weld shape. A fatigue resistant design on the fillet weld between the shell covers and the jacket is an important point on the helium inlet structure. A weld filler material was selected based on tensile test at liquid helium temperature after Nb$_{3}$Sn reaction heat treatment. To validate the design of the weld joint, fatigue tests at 7 K were performed using heat-treated butt weld samples. A pressure drop measurement of a helium inlet mock-up was performed by using nitrogen gas at room temperature in order to confirm uniform flow distribution and pressure drop characteristic. These tests have validated the helium inlet design. Based on the validation, Japanese and European Union domestic agencies, which have responsibilities of the TF coil procurement, a...

Development and validation of a general approach to predict and quantify the synergism of anti-cancer drugs using experimental design and artificial neural networks.

Science.gov (United States)

Pivetta, Tiziana; Isaia, Francesco; Trudu, Federica; Pani, Alessandra; Manca, Matteo; Perra, Daniela; Amato, Filippo; Havel, Josef

2013-10-15

The combination of two or more drugs using multidrug mixtures is a trend in the treatment of cancer. The goal is to search for a synergistic effect and thereby reduce the required dose and inhibit the development of resistance. An advanced model-free approach for data exploration and analysis, based on artificial neural networks (ANN) and experimental design is proposed to predict and quantify the synergism of drugs. The proposed method non-linearly correlates the concentrations of drugs with the cytotoxicity of the mixture, providing the possibility of choosing the optimal drug combination that gives the maximum synergism. The use of ANN allows for the prediction of the cytotoxicity of each combination of drugs in the chosen concentration interval. The method was validated by preparing and experimentally testing the combinations with the predicted highest synergistic effect. In all cases, the data predicted by the network were experimentally confirmed. The method was applied to several binary mixtures of cisplatin and [Cu(1,10-orthophenanthroline)2(H2O)](ClO4)2, Cu(1,10-orthophenanthroline)(H2O)2(ClO4)2 or [Cu(1,10-orthophenanthroline)2(imidazolidine-2-thione)](ClO4)2. The cytotoxicity of the two drugs, alone and in combination, was determined against human acute T-lymphoblastic leukemia cells (CCRF-CEM). For all systems, a synergistic effect was found for selected combinations. © 2013 Elsevier B.V. All rights reserved.

Experimental validation of wireless communication with chaos

International Nuclear Information System (INIS)

Ren, Hai-Peng; Bai, Chao; Liu, Jian; Baptista, Murilo S.; Grebogi, Celso

2016-01-01

The constraints of a wireless physical media, such as multi-path propagation and complex ambient noises, prevent information from being communicated at low bit error rate. Surprisingly, it has only recently been shown that, from a theoretical perspective, chaotic signals are optimal for communication. It maximises the receiver signal-to-noise performance, consequently minimizing the bit error rate. This work demonstrates numerically and experimentally that chaotic systems can in fact be used to create a reliable and efficient wireless communication system. Toward this goal, we propose an impulsive control method to generate chaotic wave signals that encode arbitrary binary information signals and an integration logic together with the match filter capable of decreasing the noise effect over a wireless channel. The experimental validation is conducted by inputting the signals generated by an electronic transmitting circuit to an electronic circuit that emulates a wireless channel, where the signals travel along three different paths. The output signal is decoded by an electronic receiver, after passing through a match filter.

Experimental validation of wireless communication with chaos

Energy Technology Data Exchange (ETDEWEB)

Ren, Hai-Peng; Bai, Chao; Liu, Jian [Shaanxi Key Laboratory of Complex System Control and Intelligent Information Processing, Xian University of Technology, Xian 710048 (China); Baptista, Murilo S.; Grebogi, Celso [Institute for Complex System and Mathematical Biology, SUPA, University of Aberdeen, Aberdeen AB24 3UE (United Kingdom)

2016-08-15

The constraints of a wireless physical media, such as multi-path propagation and complex ambient noises, prevent information from being communicated at low bit error rate. Surprisingly, it has only recently been shown that, from a theoretical perspective, chaotic signals are optimal for communication. It maximises the receiver signal-to-noise performance, consequently minimizing the bit error rate. This work demonstrates numerically and experimentally that chaotic systems can in fact be used to create a reliable and efficient wireless communication system. Toward this goal, we propose an impulsive control method to generate chaotic wave signals that encode arbitrary binary information signals and an integration logic together with the match filter capable of decreasing the noise effect over a wireless channel. The experimental validation is conducted by inputting the signals generated by an electronic transmitting circuit to an electronic circuit that emulates a wireless channel, where the signals travel along three different paths. The output signal is decoded by an electronic receiver, after passing through a match filter.

Experimental validation of wireless communication with chaos.

Science.gov (United States)

Ren, Hai-Peng; Bai, Chao; Liu, Jian; Baptista, Murilo S; Grebogi, Celso

2016-08-01

The constraints of a wireless physical media, such as multi-path propagation and complex ambient noises, prevent information from being communicated at low bit error rate. Surprisingly, it has only recently been shown that, from a theoretical perspective, chaotic signals are optimal for communication. It maximises the receiver signal-to-noise performance, consequently minimizing the bit error rate. This work demonstrates numerically and experimentally that chaotic systems can in fact be used to create a reliable and efficient wireless communication system. Toward this goal, we propose an impulsive control method to generate chaotic wave signals that encode arbitrary binary information signals and an integration logic together with the match filter capable of decreasing the noise effect over a wireless channel. The experimental validation is conducted by inputting the signals generated by an electronic transmitting circuit to an electronic circuit that emulates a wireless channel, where the signals travel along three different paths. The output signal is decoded by an electronic receiver, after passing through a match filter.

Experimental validation of the design method to prevent flow-induced vibration in high Reynolds-number

International Nuclear Information System (INIS)

Sakai, Takaaki; Yamaguchi, Akira; Morisita, Masaki; Iwata, Koji

1998-08-01

The incident of sodium leakage from a main pipe of the secondary heat transport system of Monju fast breeder reactor was caused by the failure of a thermometer well. 'Flow-induced vibration design guide for thermometer wells' (express as 'design guide') was proposed by PNC Working Group to prevent the same cause of the sodium leak incident in future. On this report, applicability of the 'design guide' was estimated to plant conditions in high Reynolds-number(approximately 3x10 5 ∼ 3x10 6 ) involving the supercritical region, by measured data on a vortex synchronized vibration and a turbulence induced vibration. Experiments were performed for cylindrical and taper shaped types of test pieces. As results, reduced velocity (Vr) at onsets of the inline synchronized vibration were evaluated to be grater than 1.0 in the range of experimental conditions. Fluctuating drag and lift coefficients, which were evaluated from power spectrum of turbulence for Vr < 1.0 condition, were 0.01 ∼ 0.05 for drag direction and 0.04 ∼ 0.13 for lift direction. The fluctuating drag and lift coefficients used in the 'design guide' were estimated to be conservative by comparison with these data. Correlation lengths for a cylinder and a taper shaped one in the high Reynolds-number region were estimated to be 1.6 times of the diameter(D) in the maximum case. The measured value of correlation length is enough smaller than the 'design guide' value of 3.0D. Displacement amplitudes of test pieces for Vr < 1.0 conditions were enough smaller (fives times) than calculated values based on the 'design guide'. Consequently, the applicability of the design guide' was confirmed in the range of experiments involving the super critical Reynolds-number region. (author)

Validation of Experimental whole-body SAR Assessment Method in a Complex Indoor Environment

DEFF Research Database (Denmark)

Bamba, Aliou; Joseph, Wout; Vermeeren, Gunter

2012-01-01

Assessing experimentally the whole-body specific absorption rate (SARwb) in a complex indoor environment is very challenging. An experimental method based on room electromagnetics theory (accounting only the Line-Of-Sight as specular path) to assess the whole-body SAR is validated by numerical...... of the proposed method is that it allows discarding the computation burden because it does not use any discretizations. Results show good agreement between measurement and computation at 2.8 GHz, as long as the plane wave assumption is valid, i.e., for high distances from the transmitter. Relative deviations 0...

Physics of subcritical multiplying regions and experimental validation

International Nuclear Information System (INIS)

Salvatores, M.

1996-01-01

The coupling of a particle accelerator with a spallation target and with a subcritical multiplying region has been proposed in the fifties and is called here a hybrid system. This article gives some ideas about the energetic balance of such a system. The possibilities of experimental validation of some properties of a subcritical multiplying region by using MASURCA facility at CEA-Cadarache are examined. The results of a preliminary experiment called MUSE are presented. (A.C.)

Experimental Validation of a Wave Energy Converter Array Hydrodynamics Tool

DEFF Research Database (Denmark)

Ruiz, Pau Mercadé; Ferri, Francesco; Kofoed, Jens Peter

2017-01-01

This paper uses experimental data to validate a wave energy converter (WEC) array hydrodynamics tool developed within the context of linearized potential flow theory. To this end, wave forces and power absorption by an array of five-point absorber WECs in monochromatic and panchromatic waves were...

Numerical multi-criteria optimization methods for alloy design. Development of new high strength nickel-based superalloys and experimental validation

Energy Technology Data Exchange (ETDEWEB)

Rettig, Ralf; Mueller, Alexander; Ritter, Nils C.; Singer, Robert F. [Institute of Science and Technology of Metals, Department of Materials Science and Engineering, University of Erlangen (Germany)

2016-07-01

A new approach for the design of optimum balanced metallic alloys is presented. It is based on a mathematical multi-criteria optimization method which uses different property models to predict the alloy behavior in dependency of composition. These property models are mostly based on computational thermodynamics (CALPHAD-method). The full composition range of the alloying elements can be considered using these models. In alloy design usually several contradicting goals have to be fulfilled. This is handled by the calculation of so-called Pareto-fronts. The aim of our approach is to guide the experimental research towards new alloy compositions that have a high probability of having very good properties. Consequently the number of required test alloys can be massively reduced. The approach will be demonstrated for the computer-aided design of a new Re-free superalloy with nearly identical creep strength as that of Re-containing superalloys. Our starting point for the design was to maintain the good properties of the gamma prime-phase in well-known alloys like CMSX-4 and to maximize the solid solution strengthening of W and Mo. The presented experimental measurements proof the excellent properties.

Sequential experimental design based generalised ANOVA

Energy Technology Data Exchange (ETDEWEB)

Chakraborty, Souvik, E-mail: csouvik41@gmail.com; Chowdhury, Rajib, E-mail: rajibfce@iitr.ac.in

2016-07-15

Over the last decade, surrogate modelling technique has gained wide popularity in the field of uncertainty quantification, optimization, model exploration and sensitivity analysis. This approach relies on experimental design to generate training points and regression/interpolation for generating the surrogate. In this work, it is argued that conventional experimental design may render a surrogate model inefficient. In order to address this issue, this paper presents a novel distribution adaptive sequential experimental design (DA-SED). The proposed DA-SED has been coupled with a variant of generalised analysis of variance (G-ANOVA), developed by representing the component function using the generalised polynomial chaos expansion. Moreover, generalised analytical expressions for calculating the first two statistical moments of the response, which are utilized in predicting the probability of failure, have also been developed. The proposed approach has been utilized in predicting probability of failure of three structural mechanics problems. It is observed that the proposed approach yields accurate and computationally efficient estimate of the failure probability.

Design and experimental study of a multi-modal piezoelectric energy harvester

Energy Technology Data Exchange (ETDEWEB)

Xiong, Xing Yu [School of Energy, Power and Mechanical Engineering, North China Electric Power University, Beijing (China); Oyadiji, S. Olutunde [School of Mechanical, Aerospace and Civil Engineering, The University of Manchester, Manchester (United States)

2017-01-15

A multi-modal piezoelectric vibration energy harvester is designed in this article. It consists of a cantilevered base beam and some upper and lower layer beams with rigid masses bonded between the beams as spacers. For a four-layer harvester subjected to random base excitations, relocating the mass positions leads to the generation of up to four close resonance frequencies over the frequency range from 10 Hz to 100 Hz with relative large power output. The harvesters are connected with a resistance decade box and the frequency response functions of the voltage and power on resistive loads are determined. The experimental results are validated with the simulation results using the finite element method. On a certain level of power output, the experimental results show that the multi-modal harvesters can generate a frequency band that is more than two times greater than the frequency band produced by a cantilevered beam harvester.

Validation of a Wave-Body Interaction Model by Experimental Tests

DEFF Research Database (Denmark)

Ferri, Francesco; Kramer, Morten; Pecher, Arthur

2013-01-01

Within the wave energy field, numerical simulation has recently acquired a worldwide consent as being a useful tool, besides physical model testing. The main goal of this work is the validation of a numerical model by experimental results. The numerical model is based on a linear wave-body intera...

Experimental Validation of a Dynamic Model for Lightweight Robots

Directory of Open Access Journals (Sweden)

Alessandro Gasparetto

2013-03-01

Full Text Available Nowadays, one of the main topics in robotics research is dynamic performance improvement by means of a lightening of the overall system structure. The effective motion and control of these lightweight robotic systems occurs with the use of suitable motion planning and control process. In order to do so, model-based approaches can be adopted by exploiting accurate dynamic models that take into account the inertial and elastic terms that are usually neglected in a heavy rigid link configuration. In this paper, an effective method for modelling spatial lightweight industrial robots based on an Equivalent Rigid Link System approach is considered from an experimental validation perspective. A dynamic simulator implementing the formulation is used and an experimental test-bench is set-up. Experimental tests are carried out with a benchmark L-shape mechanism.

Experimental results and validation of a method to reconstruct forces on the ITER test blanket modules

International Nuclear Information System (INIS)

Zeile, Christian; Maione, Ivan A.

2015-01-01

Highlights: • An in operation force measurement system for the ITER EU HCPB TBM has been developed. • The force reconstruction methods are based on strain measurements on the attachment system. • An experimental setup and a corresponding mock-up have been built. • A set of test cases representing ITER relevant excitations has been used for validation. • The influence of modeling errors on the force reconstruction has been investigated. - Abstract: In order to reconstruct forces on the test blanket modules in ITER, two force reconstruction methods, the augmented Kalman filter and a model predictive controller, have been selected and developed to estimate the forces based on strain measurements on the attachment system. A dedicated experimental setup with a corresponding mock-up has been designed and built to validate these methods. A set of test cases has been defined to represent possible excitation of the system. It has been shown that the errors in the estimated forces mainly depend on the accuracy of the identified model used by the algorithms. Furthermore, it has been found that a minimum of 10 strain gauges is necessary to allow for a low error in the reconstructed forces.

Design rules for piping: experimental validation of flexibility and elastic stress indices for elbows under bending

International Nuclear Information System (INIS)

Touboul, F.; Ben Jdidia, M.; Acker, D.

1989-01-01

Design rules for class 1 piping components are based on stress indices (B, C, K) and flexibility factors (k). For elbows, adjacent straight parts and internal pressure inhibit ovalization of the cross-section, so reducing the sub-mentioned indices. Published theoretical works and experimental results allow for improvement of coded values. End effect may be represented by a suitable function of the elbow angle. The favourable effect of pressure on C 2 , for fatigue damage evaluation, can be taken into account

Model validation using CFD-grade experimental database for NGNP Reactor Cavity Cooling Systems with water and air

Energy Technology Data Exchange (ETDEWEB)

Manera, Annalisa [Univ. of Michigan, Ann Arbor, MI (United States); Corradini, Michael [Univ. of Wisconsin, Madison, WI (United States); Petrov, Victor [Univ. of Michigan, Ann Arbor, MI (United States); Anderson, Mark [Univ. of Wisconsin, Madison, WI (United States); Tompkins, Casey [Univ. of Wisconsin, Madison, WI (United States); Nunez, Daniel [Univ. of Michigan, Ann Arbor, MI (United States)

2018-02-13

This project has been focused on the experimental and numerical investigations of the water-cooled and air-cooled Reactor Cavity Cooling System (RCCS) designs. At this aim, we have leveraged an existing experimental facility at the University of Wisconsin-Madison (UW), and we have designed and built a separate effect test facility at the University of Michigan. The experimental facility at UW has underwent several upgrades, including the installation of advanced instrumentation (i.e. wire-mesh sensors) built at the University of Michigan. These provides highresolution time-resolved measurements of the void-fraction distribution in the risers of the water-cooled RCCS facility. A phenomenological model has been developed to assess the water cooled RCCS system stability and determine the root cause behind the oscillatory behavior that occurs under normal two-phase operation. Testing under various perturbations to the water-cooled RCCS facility have resulted in changes in the stability of the integral system. In particular, the effects on stability of inlet orifices, water tank volume have and system pressure been investigated. MELCOR was used as a predictive tool when performing inlet orificing tests and was able to capture the Density Wave Oscillations (DWOs) that occurred upon reaching saturation in the risers. The experimental and numerical results have then been used to provide RCCS design recommendations. The experimental facility built at the University of Michigan was aimed at the investigation of mixing in the upper plenum of the air-cooled RCCS design. The facility has been equipped with state-of-theart high-resolution instrumentation to achieve so-called CFD grade experiments, that can be used for the validation of Computational Fluid Dynanmics (CFD) models, both RANS (Reynold-Averaged) and LES (Large Eddy Simulations). The effect of risers penetration in the upper plenum has been investigated as well.

Dynamic modeling and experimental validation for direct contact membrane distillation (DCMD) process

KAUST Repository

Eleiwi, Fadi

2016-02-01

This work proposes a mathematical dynamic model for the direct contact membrane distillation (DCMD) process. The model is based on a 2D Advection–Diffusion Equation (ADE), which describes the heat and mass transfer mechanisms that take place inside the DCMD module. The model studies the behavior of the process in the time varying and the steady state phases, contributing to understanding the process performance, especially when it is driven by intermittent energy supply, such as the solar energy. The model is experimentally validated in the steady state phase, where the permeate flux is measured for different feed inlet temperatures and the maximum absolute error recorded is 2.78 °C. Moreover, experimental validation includes the time variation phase, where the feed inlet temperature ranges from 30 °C to 75 °C with 0.1 °C increment every 2min. The validation marks relative error to be less than 5%, which leads to a strong correlation between the model predictions and the experiments.

Dynamic modeling and experimental validation for direct contact membrane distillation (DCMD) process

KAUST Repository

Eleiwi, Fadi; Ghaffour, NorEddine; Alsaadi, Ahmad Salem; Francis, Lijo; Laleg-Kirati, Taous-Meriem

2016-01-01

This work proposes a mathematical dynamic model for the direct contact membrane distillation (DCMD) process. The model is based on a 2D Advection–Diffusion Equation (ADE), which describes the heat and mass transfer mechanisms that take place inside the DCMD module. The model studies the behavior of the process in the time varying and the steady state phases, contributing to understanding the process performance, especially when it is driven by intermittent energy supply, such as the solar energy. The model is experimentally validated in the steady state phase, where the permeate flux is measured for different feed inlet temperatures and the maximum absolute error recorded is 2.78 °C. Moreover, experimental validation includes the time variation phase, where the feed inlet temperature ranges from 30 °C to 75 °C with 0.1 °C increment every 2min. The validation marks relative error to be less than 5%, which leads to a strong correlation between the model predictions and the experiments.

Validation of helium inlet design for ITER toroidal field coil

International Nuclear Information System (INIS)

Boyer, C.; Seo, K.; Hamada, K.; Foussat, A.; Le Rest, M.; Mitchell, N.; Decool, P.; Savary, F.; Sgobba, S.; Weiss, K.P.

2014-01-01

The ITER organization has performed design and its validation tests on a helium inlet structure for the ITER Toroidal Field (TF) coil under collaboration with CERN, KIT, and CEA Cadarache. Detailed structural analysis was performed in order to optimize the weld shape. A fatigue resistant design on the fillet weld between the shell covers and the jacket is an important point on the helium inlet structure. A weld filler material was selected based on tensile test at liquid helium temperature after Nb 3 Sn reaction heat treatment. To validate the design of the weld joint, fatigue tests at 7 K were performed using heat-treated butt weld samples. A pressure drop measurement of a helium inlet mock-up was performed by using nitrogen gas at room temperature in order to confirm uniform flow distribution and pressure drop characteristic. These tests have validated the helium inlet design. Based on the validation, Japanese and European Union domestic agencies, which have responsibilities of the TF coil procurement, are preparing the helium inlet mock-up for a qualification test. (authors)

Creating and validating GIS measures of urban design for health research.

Science.gov (United States)

Purciel, Marnie; Neckerman, Kathryn M; Lovasi, Gina S; Quinn, James W; Weiss, Christopher; Bader, Michael D M; Ewing, Reid; Rundle, Andrew

2009-12-01

Studies relating urban design to health have been impeded by the unfeasibility of conducting field observations across large areas and the lack of validated objective measures of urban design. This study describes measures for five dimensions of urban design - imageability, enclosure, human scale, transparency, and complexity - created using public geographic information systems (GIS) data from the US Census and city and state government. GIS measures were validated for a sample of 588 New York City block faces using a well-documented field observation protocol. Correlations between GIS and observed measures ranged from 0.28 to 0.89. Results show valid urban design measures can be constructed from digital sources.

Validation of experimental molecular crystal structures with dispersion-corrected density functional theory calculations.

Science.gov (United States)

van de Streek, Jacco; Neumann, Marcus A

2010-10-01

This paper describes the validation of a dispersion-corrected density functional theory (d-DFT) method for the purpose of assessing the correctness of experimental organic crystal structures and enhancing the information content of purely experimental data. 241 experimental organic crystal structures from the August 2008 issue of Acta Cryst. Section E were energy-minimized in full, including unit-cell parameters. The differences between the experimental and the minimized crystal structures were subjected to statistical analysis. The r.m.s. Cartesian displacement excluding H atoms upon energy minimization with flexible unit-cell parameters is selected as a pertinent indicator of the correctness of a crystal structure. All 241 experimental crystal structures are reproduced very well: the average r.m.s. Cartesian displacement for the 241 crystal structures, including 16 disordered structures, is only 0.095 Å (0.084 Å for the 225 ordered structures). R.m.s. Cartesian displacements above 0.25 A either indicate incorrect experimental crystal structures or reveal interesting structural features such as exceptionally large temperature effects, incorrectly modelled disorder or symmetry breaking H atoms. After validation, the method is applied to nine examples that are known to be ambiguous or subtly incorrect.

Progress in IFMIF Engineering Validation and Engineering Design Activities

International Nuclear Information System (INIS)

Heidinger, R.; Knaster, J.; Matsumoto, H.; Sugimoto, M.; Mosnier, A.; Arbeiter, F.; Baluc, N.; Cara, P.; Chel, S.; Facco, A.; Favuzza, P.; Heinzel, V.; Ibarra, A.; Massaut, V.; Micciche, G.; Nitti, F.S.; Theile, J.

2013-01-01

Highlights: ► The IFMIF/EVEDA project has entered into the crucial phase of concluding the Interim IFMIF Engineering Design Report. ► The IFMIF plant configuration has been established with the definition of five IFMIF facilities and of their interfaces. ► Three major prototypes of the IFMIF main systems have been designed and are being manufactured, commissioned and operated. -- Abstract: The International Fusion Materials Irradiation Facility (IFMIF) Engineering Design and Engineering Validation Activities (EVEDA) are being developed in a joint project in the framework of the Broader Approach (BA) Agreement between EU and Japan. This project has now entered into a crucial phase as the engineering design of IFMIF is now being formulated in a series of 3 subsequent phases for delivering an Interim IFMIF Engineering Design Report (IIEDR) by mid of 2013. Content of these phases is explained, including the plant configuration detailing the 5 IFMIF facilities and their systems. Together with the Engineering Design Activities, prototyping sub-projects are pursued in the Engineering Validation Activities which consist of the design, manufacturing and testing of the following prototypical systems: Linear IFMIF Prototype Accelerator (LIPAc), EVEDA Lithium Test Loop (ELTL), and High Flux Test Module (HFTM) with the prototypical helium cooling loop (HELOKA). Highlights are described from recent experiments in the Engineering Validation Activities

The European contribution to the development and validation activities for the design of IFMIF lithium facility

Energy Technology Data Exchange (ETDEWEB)

Miccichè, Gioacchino, E-mail: gioacchino.micciche@enea.it [EURATOM-ENEA, CR Brasimone I-40035 Camugnano, BO (Italy); Aiello, Antonio; Bernardi, Davide; Favuzza, Paolo; Agostini, Pietro [EURATOM-ENEA, CR Brasimone I-40035 Camugnano, BO (Italy); Frisoni, Manuela [EURATOM-ENEA, CR Bologna I-40129, BO Italy (Italy); Pinna, Tonio; Porfiri, MariaTeresa [EURATOM-ENEA, CR Frascati I-0044 Frascati, Roma (Italy); Tincani, Amelia [EURATOM-ENEA, CR Brasimone I-40035 Camugnano, BO (Italy); Di Maio, PieroAlessandro [University of Palermo, I-90128 Palermo (Italy); Knaepen, Bernard [Université libre de Bruxelles, I-1050 Bruxelles (Belgium)

2013-10-15

Highlights: • Engineering design of the target assembly. • Erosion, corrosion phenomena promoted by the lithium are studied. • Purification system implemented in the LiFus6 loop. • Study of the remote handling maintenance for the IFMIF TA. -- Abstract: The International Fusion Materials Irradiation Facility (IFMIF) is an accelerator-driven intense neutron source where candidate materials for fusion reactors will be tested and validated. The high energy neutron flux is produced by means of two deuteron beams (total current of 250 mA, energy of 40 MeV) that strikes a liquid lithium target circulating in a lithium loop of IFMIF plant. The European (EU) contribution to the development of the lithium facility comprises five procurement packages, as follow: (1) participation to the experimental activities of the EVEDA lithium test loop in Oarai (Japan); (2) study aimed at evaluating the corrosion and erosion phenomena, promoted by lithium, for structural fusion reference materials like AISI 316L and Eurofer; (3) design and validation of the lithium purification method with the aim to provide input data for the design of the purification system of IFIMF lithium loop; (4) design and validation of the remote handling (RH) procedures for the refurbishment/replacement of the EU concept of IFMIF target assembly including the design of the remote handling tools; (5) the engineering design of the European target assembly for IFMIF and the safety and RAMI analyses for the entire IFMIF lithium facility. The paper gives an overview of the status of the activities and of the main outcomes achieved so far.

The European contribution to the development and validation activities for the design of IFMIF lithium facility

International Nuclear Information System (INIS)

Miccichè, Gioacchino; Aiello, Antonio; Bernardi, Davide; Favuzza, Paolo; Agostini, Pietro; Frisoni, Manuela; Pinna, Tonio; Porfiri, MariaTeresa; Tincani, Amelia; Di Maio, PieroAlessandro; Knaepen, Bernard

2013-01-01

Highlights: • Engineering design of the target assembly. • Erosion, corrosion phenomena promoted by the lithium are studied. • Purification system implemented in the LiFus6 loop. • Study of the remote handling maintenance for the IFMIF TA. -- Abstract: The International Fusion Materials Irradiation Facility (IFMIF) is an accelerator-driven intense neutron source where candidate materials for fusion reactors will be tested and validated. The high energy neutron flux is produced by means of two deuteron beams (total current of 250 mA, energy of 40 MeV) that strikes a liquid lithium target circulating in a lithium loop of IFMIF plant. The European (EU) contribution to the development of the lithium facility comprises five procurement packages, as follow: (1) participation to the experimental activities of the EVEDA lithium test loop in Oarai (Japan); (2) study aimed at evaluating the corrosion and erosion phenomena, promoted by lithium, for structural fusion reference materials like AISI 316L and Eurofer; (3) design and validation of the lithium purification method with the aim to provide input data for the design of the purification system of IFIMF lithium loop; (4) design and validation of the remote handling (RH) procedures for the refurbishment/replacement of the EU concept of IFMIF target assembly including the design of the remote handling tools; (5) the engineering design of the European target assembly for IFMIF and the safety and RAMI analyses for the entire IFMIF lithium facility. The paper gives an overview of the status of the activities and of the main outcomes achieved so far

Design and application on experimental platform for high-speed bearing with grease lubrication

Directory of Open Access Journals (Sweden)

He Qiang

2015-12-01

Full Text Available The experimental platform for high-speed grease is an important tool for research and development of high-speed motorized spindle with grease lubrication. In this article, the experimental platform for high-speed grease is designed and manufactured which consists of the drive system, the test portion, the loading system, the lubrication system, the control system, and so on. In the meantime, the high-speed angular contact ceramic ball bearings B7005C/HQ1P4 as the research object are tested and contrasted in the grease lubrication and oil mist lubrication. The experimental platform performance is validated by contrast experiment, and the high-speed lubricated bearing performance is also studied especially in the relationship among the rotating speed,load and temperature rise. The results show that the experimental platform works steadily, accurate, and reliable in the experimental testing. And the grease lubrication ceramic ball bearings B7005C/HQ1P4 can be used in high-speed motorized spindle in the circular water cooling conditions when the rotating speed is lower than 40,000 r/min or the DN value (the value of the bearing diameter times the rotating speed is lower than the 1.44 × 106 mm r/min. Grease lubrication instead of oil mist lubrication under high-speed rotating will simplify the structure design of the high-speed motorized spindle and reduce the pollution to the environment.

Constructing experimental designs for discrete-choice experiments: report of the ISPOR Conjoint Analysis Experimental Design Good Research Practices Task Force.

Science.gov (United States)

Reed Johnson, F; Lancsar, Emily; Marshall, Deborah; Kilambi, Vikram; Mühlbacher, Axel; Regier, Dean A; Bresnahan, Brian W; Kanninen, Barbara; Bridges, John F P

2013-01-01

Stated-preference methods are a class of evaluation techniques for studying the preferences of patients and other stakeholders. While these methods span a variety of techniques, conjoint-analysis methods-and particularly discrete-choice experiments (DCEs)-have become the most frequently applied approach in health care in recent years. Experimental design is an important stage in the development of such methods, but establishing a consensus on standards is hampered by lack of understanding of available techniques and software. This report builds on the previous ISPOR Conjoint Analysis Task Force Report: Conjoint Analysis Applications in Health-A Checklist: A Report of the ISPOR Good Research Practices for Conjoint Analysis Task Force. This report aims to assist researchers specifically in evaluating alternative approaches to experimental design, a difficult and important element of successful DCEs. While this report does not endorse any specific approach, it does provide a guide for choosing an approach that is appropriate for a particular study. In particular, it provides an overview of the role of experimental designs for the successful implementation of the DCE approach in health care studies, and it provides researchers with an introduction to constructing experimental designs on the basis of study objectives and the statistical model researchers have selected for the study. The report outlines the theoretical requirements for designs that identify choice-model preference parameters and summarizes and compares a number of available approaches for constructing experimental designs. The task-force leadership group met via bimonthly teleconferences and in person at ISPOR meetings in the United States and Europe. An international group of experimental-design experts was consulted during this process to discuss existing approaches for experimental design and to review the task force's draft reports. In addition, ISPOR members contributed to developing a consensus

Spent Nuclear Fuel (SNF) Project Design Verification and Validation Process

International Nuclear Information System (INIS)

OLGUIN, L.J.

2000-01-01

This document provides a description of design verification and validation activities implemented by the Spent Nuclear Fuel (SNF) Project. During the execution of early design verification, a management assessment (Bergman, 1999) and external assessments on configuration management (Augustenburg, 1999) and testing (Loscoe, 2000) were conducted and identified potential uncertainties in the verification process. This led the SNF Chief Engineer to implement corrective actions to improve process and design products. This included Design Verification Reports (DVRs) for each subproject, validation assessments for testing, and verification of the safety function of systems and components identified in the Safety Equipment List to ensure that the design outputs were compliant with the SNF Technical Requirements. Although some activities are still in progress, the results of the DVR and associated validation assessments indicate that Project requirements for design verification are being effectively implemented. These results have been documented in subproject-specific technical documents (Table 2). Identified punch-list items are being dispositioned by the Project. As these remaining items are closed, the technical reports (Table 2) will be revised and reissued to document the results of this work

Experimental design research approaches, perspectives, applications

CERN Document Server

Stanković, Tino; Štorga, Mario

2016-01-01

This book presents a new, multidisciplinary perspective on and paradigm for integrative experimental design research. It addresses various perspectives on methods, analysis and overall research approach, and how they can be synthesized to advance understanding of design. It explores the foundations of experimental approaches and their utility in this domain, and brings together analytical approaches to promote an integrated understanding. The book also investigates where these approaches lead to and how they link design research more fully with other disciplines (e.g. psychology, cognition, sociology, computer science, management). Above all, the book emphasizes the integrative nature of design research in terms of the methods, theories, and units of study—from the individual to the organizational level. Although this approach offers many advantages, it has inherently led to a situation in current research practice where methods are diverging and integration between individual, team and organizational under...

Development and validation of natural circulation based systems for new WWER designs

International Nuclear Information System (INIS)

Kurakov, Y.A.; Dragunov, Y.G.; Podshibiakin, A.K.; Fil, N.S.; Logvinov, S.A.; Sitnik, Y.K.; Berkovich, V.M.; Taranov, G.S.

2002-01-01

Elaboration and introduction of NPP designs with improved technical and economic parameters are defined as an important element of the National Program of nuclear power development approved by the Russian Federation Government in 1998. This Program considers the designs of WWER-1000/V-392 and WWER-640/ V-407 power units as the priority projects of the new generation NPPs with increased safety. A number of passive systems based on natural circulation phenomena are used in V-392 and V-407 designs to prevent or mitigate severe accidents. Design basis, configuration and effect of some naturally driven systems of V-392 design sited at Novovoronezh are mainly reflected in the present paper. One of the most important mean for severe accident prevention in V-392 design is so called SPOT - passive heat removal system designed to remove core decay heat in case of station blackout (including failure of all diesel generators). This system extracts the steam from the steam generator, condenses it and returns water to steam generator by natural circulation. The SPOT heat exchangers are cooled by atmospheric air coming by natural circulation through a special direct action control gates which operate passively as well. Extensive experimental investigation of the different aspects of this system operation has been carried out to validate its functioning under real plant conditions. In particular, full-scale section of air heat exchanger-condenser has been tested with natural circulation steam, condensate and air paths modeled. The environment air temperature and steam pressure condensing were varied in the wide range, and the relevant experimental results are being discussed in this paper. The effect of wind velocity and direction to the containment is also checked by the experiments. (author)

Experimental and computational validation of BDTPS using a heterogeneous boron phantom

CERN Document Server

Daquino, G G; Mazzini, M; Moss, R L; Muzi, L

2004-01-01

The idea to couple the treatment planning system (TPS) to the information on the real boron distribution in the patient acquired by positron emission tomography (PET) is the main added value of the new methodology set-up at DIMNP (Dipartimento di Ingegneria Meccanica, Nucleare e della Produzione) of University of Pisa, in collaboration with the JRC (Joint Research Centre) at Petten (NL). This methodology has been implemented in a new TPS, called Boron Distribution Treatment Planning System (BDTPS), which takes into account the actual boron distribution in the patient's organ, as opposed to other TPSs used in BNCT that assume an ideal uniform boron distribution. BDTPS is based on the Monte Carlo technique and has been experimentally validated comparing the computed main parameters (thermal neutron flux, boron dose, etc.) to those measured during the irradiation of an ad hoc designed phantom (HEterogeneous BOron phanto M, HEBOM). The results are also in good agreement with those obtained by the standard TPS SER...

Validation of scaffold design optimization in bone tissue engineering: finite element modeling versus designed experiments.

Science.gov (United States)

Uth, Nicholas; Mueller, Jens; Smucker, Byran; Yousefi, Azizeh-Mitra

2017-02-21

This study reports the development of biological/synthetic scaffolds for bone tissue engineering (TE) via 3D bioplotting. These scaffolds were composed of poly(L-lactic-co-glycolic acid) (PLGA), type I collagen, and nano-hydroxyapatite (nHA) in an attempt to mimic the extracellular matrix of bone. The solvent used for processing the scaffolds was 1,1,1,3,3,3-hexafluoro-2-propanol. The produced scaffolds were characterized by scanning electron microscopy, microcomputed tomography, thermogravimetric analysis, and unconfined compression test. This study also sought to validate the use of finite-element optimization in COMSOL Multiphysics for scaffold design. Scaffold topology was simplified to three factors: nHA content, strand diameter, and strand spacing. These factors affect the ability of the scaffold to bear mechanical loads and how porous the structure can be. Twenty four scaffolds were constructed according to an I-optimal, split-plot designed experiment (DE) in order to generate experimental models of the factor-response relationships. Within the design region, the DE and COMSOL models agreed in their recommended optimal nHA (30%) and strand diameter (460 μm). However, the two methods disagreed by more than 30% in strand spacing (908 μm for DE; 601 μm for COMSOL). Seven scaffolds were 3D-bioplotted to validate the predictions of DE and COMSOL models (4.5-9.9 MPa measured moduli). The predictions for these scaffolds showed relative agreement for scaffold porosity (mean absolute percentage error of 4% for DE and 13% for COMSOL), but were substantially poorer for scaffold modulus (51% for DE; 21% for COMSOL), partly due to some simplifying assumptions made by the models. Expanding the design region in future experiments (e.g., higher nHA content and strand diameter), developing an efficient solvent evaporation method, and exerting a greater control over layer overlap could allow developing PLGA-nHA-collagen scaffolds to meet the mechanical requirements for

Optimization Design Method and Experimental Validation of a Solar PVT Cogeneration System Based on Building Energy Demand

Directory of Open Access Journals (Sweden)

Chao Zhou

2017-08-01

Full Text Available Photovoltaic-thermal (PVT technology refers to the integration of a photovoltaic (PV and a conventional solar thermal collector, representing the deep exploitation and utilization of solar energy. In this paper, we evaluate the performance of a solar PVT cogeneration system based on specific building energy demand using theoretical modeling and experimental study. Through calculation and simulation, the dynamic heating load and electricity load is obtained as the basis of the system design. An analytical expression for the connection of PVT collector array is derived by using basic energy balance equations and thermal models. Based on analytical results, an optimized design method was carried out for the system. In addition, the fuzzy control method of frequency conversion circulating water pumps and pipeline switching by electromagnetic valves is introduced in this paper to maintain the system at an optimal working point. Meanwhile, an experimental setup is established, which includes 36 PVT collectors with every 6 PVT collectors connected in series. The thermal energy generation, thermal efficiency, power generation and photovoltaic efficiency have been given in this paper. The results demonstrate that the demonstration solar PVT cogeneration system can meet the building energy demand in the daytime in the heating season.

Dislocation-mediated strain hardening in tungsten: Thermo-mechanical plasticity theory and experimental validation

Science.gov (United States)

Terentyev, Dmitry; Xiao, Xiazi; Dubinko, A.; Bakaeva, A.; Duan, Huiling

2015-12-01

A self-consistent thermo-mechanical model to study the strain-hardening behavior of polycrystalline tungsten was developed and validated by a dedicated experimental route. Dislocation-dislocation multiplication and storage, as well dislocation-grain boundary (GB) pinning were the major mechanisms underlying the evolution of plastic deformation, thus providing a link between the strain hardening behavior and material's microstructure. The microstructure of the polycrystalline tungsten samples has been thoroughly investigated by scanning and electron microscopy. The model was applied to compute stress-strain loading curves of commercial tungsten grades, in the as-received and as-annealed states, in the temperature range of 500-1000 °C. Fitting the model to the independent experimental results obtained using a single crystal and as-received polycrystalline tungsten, the model demonstrated its capability to predict the deformation behavior of as-annealed samples in a wide temperature range and applied strain. The relevance of the dislocation-mediated plasticity mechanisms used in the model have been validated using transmission electron microscopy examination of the samples deformed up to different amounts of strain. On the basis of the experimental validation, the limitations of the model are determined and discussed.

The reactor safety study of experimental multi-purpose VHTR design

International Nuclear Information System (INIS)

Yasuno, T.; Mitake, S.; Ezaki, M.; Suzuki, K.

1981-01-01

Over the past years, the design works of the Experimental Very High Temperature Reactor (VHTR) plant have been conducted at Japan Atomic Energy Research Institute. The conceptual design has been completed and the more detailed design works and the safety analysis of the experimental VHTR plant are continued. The purposes of design studies are to show the feasibility of the experimental VHTR program, to specify the characteristics and functions of the plant components, to point out the R and D items necessary for the experimental VHTR plant construction, and to analyze the feature of the plant safety. In this paper the summary of system design and safety features of the experimental reactor are indicated. Main issues are the safety philosophy for the design basis accident, the accidents assumed and the engineered safety systems adopted in the design works

Two polynomial representations of experimental design

OpenAIRE

Notari, Roberto; Riccomagno, Eva; Rogantin, Maria-Piera

2007-01-01

In the context of algebraic statistics an experimental design is described by a set of polynomials called the design ideal. This, in turn, is generated by finite sets of polynomials. Two types of generating sets are mostly used in the literature: Groebner bases and indicator functions. We briefly describe them both, how they are used in the analysis and planning of a design and how to switch between them. Examples include fractions of full factorial designs and designs for mixture experiments.

Numerical simulation and experimental validation of internal heat exchanger influence on CO{sub 2} trans-critical cycle performance

Energy Technology Data Exchange (ETDEWEB)

Rigola, Joaquim; Ablanque, Nicolas; Perez-Segarra, Carlos D.; Oliva, Assensi [Centre Tecnologic de Transferencia de Calor (CTTC), Universitat Politecnica de Catalunya (UPC), ETSEIAT, C. Colom 11, 08222 Terrassa (Barcelona) (Spain)

2010-06-15

The present paper is a numerical and experimental comparative study of the whole vapour compression refrigerating cycle in general, and reciprocating compressors in particular, with the aim of showing the possibilities that CO{sub 2} offers for commercial refrigeration, considering a single-stage trans-critical cycle using semi-hermetic reciprocating compressors under small cooling capacity systems. The present work is focussed on the influence of using an internal heat exchanger (IHX) in order to improve the cycle performance under real working conditions. In order to validate the numerical results, an experimental unit specially designed and built to analyze trans-critical refrigerating equipments considering IHX has been built. Both numerical results and experimental data show reasonable good agreement, while the comparative global values conclude the improvement of cooling capacity and COP when IHX is considered in the CO{sub 2} trans-critical cycle. (author)

Identification and Validation of ESP Teacher Competencies: A Research Design

Science.gov (United States)

Venkatraman, G.; Prema, P.

2013-01-01

The paper presents the research design used for identifying and validating a set of competencies required of ESP (English for Specific Purposes) teachers. The identification of the competencies and the three-stage validation process are also discussed. The observation of classes of ESP teachers for field-testing the validated competencies and…

An Experimental Validated Control Strategy of Maglev Vehicle-Bridge Self-Excited Vibration

Directory of Open Access Journals (Sweden)

Lianchun Wang

2017-01-01

Full Text Available This study discusses an experimentally validated control strategy of maglev vehicle-bridge vibration, which degrades the stability of the suspension control, deteriorates the ride comfort, and limits the cost of the magnetic levitation system. First, a comparison between the current-loop and magnetic flux feedback is carried out and a minimum model including flexible bridge and electromagnetic levitation system is proposed. Then, advantages and disadvantages of the traditional feedback architecture with the displacement feedback of electromagnet yE and bridge yB in pairs are explored. The results indicate that removing the feedback of the bridge’s displacement yB from the pairs (yE − yB measured by the eddy-current sensor is beneficial for the passivity of the levitation system and the control of the self-excited vibration. In this situation, the signal acquisition of the electromagnet’s displacement yE is discussed for the engineering application. Finally, to validate the effectiveness of the aforementioned control strategy, numerical validations are carried out and the experimental data are provided and analyzed.

Experimental Validation of a Differential Variational Inequality-Based Approach for Handling Friction and Contact in Vehicle

Science.gov (United States)

2015-11-20

terrain modeled using the discrete element method (DEM). Experimental Validation of a Differential Variational Inequality -Based Approach for Handling...COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Experimental Validation of a Differential Variational Inequality -Based Approach for...sinkage, and single wheel tests. 1.1. Modeling Frictional Contact Via Differential Variational Inequalities Consider a three dimensional (3D) system of

Validation of the generalized model of two-phase thermosyphon loop based on experimental measurements of volumetric flow rate

Science.gov (United States)

Bieliński, Henryk

2016-09-01

The current paper presents the experimental validation of the generalized model of the two-phase thermosyphon loop. The generalized model is based on mass, momentum, and energy balances in the evaporators, rising tube, condensers and the falling tube. The theoretical analysis and the experimental data have been obtained for a new designed variant. The variant refers to a thermosyphon loop with both minichannels and conventional tubes. The thermosyphon loop consists of an evaporator on the lower vertical section and a condenser on the upper vertical section. The one-dimensional homogeneous and separated two-phase flow models were used in calculations. The latest minichannel heat transfer correlations available in literature were applied. A numerical analysis of the volumetric flow rate in the steady-state has been done. The experiment was conducted on a specially designed test apparatus. Ultrapure water was used as a working fluid. The results show that the theoretical predictions are in good agreement with the measured volumetric flow rate at steady-state.

Experimental investigation of stratified two-phase flows in the hot leg of a PWR for CFD validation

Energy Technology Data Exchange (ETDEWEB)

Vallee, Christophe; Lucas, Dirk [Helmholtz-Zentrum Dresden-Rossendorf (HZDR) e.V., Dresden (Germany). Inst. of Fluid Dynamics; Tomiyama, Akio [Kobe Univ. (Japan). Graduate School of Engineering; Murase, Michio [Institute of Nuclear Safety System Inc. (INSS), Fukui (Japan)

2012-07-01

Stratified two-phase flows were investigated in two different models of the hot leg of a pressurised water reactor (PWR) in order to provide experimental data for the development and validation of computational fluid dynamics (CFD) codes. Therefore, the local flow structure was visualised with a high-speed video camera. Moreover, one test section was designed with a rectangular cross-section to achieve optimum observation conditions. The phenomenon of counter-current flow limitation (CCFL) was investigated, which may affect the reflux condenser cooling mode in some accident scenarios. (orig.)

Validation of PHITS Spallation Models from the Perspective of the Shielding Design of Transmutation Experimental Facility

Science.gov (United States)

Iwamoto, Hiroki; Meigo, Shin-ichiro

2017-09-01

The impact of different spallation models implemented in the particle transport code PHITS on the shielding design of Transmutation Experimental Facility is investigated. For 400-MeV proton incident on a lead-bismuth eutectic target, an effective dose rate at the end of a thick radiation shield (3-m-thick iron and 3-m-thick concrete) calculated by the Liège intranuclear cascade (INC) model version 4.6 (INCL4.6) coupled with the GEMcode (INCL4.6/GEM) yields about twice as high as the Bertini INC model (Bertini/GEM). A comparison with experimental data for 500-MeV proton incident on a thick lead target suggest that the prediction accuracy of INCL4.6/GEM would be better than that of Bertini/GEM. In contrast, it is found that the dose rates in beam ducts in front of targets calculated by the INCL4.6/GEMare lower than those by the Bertini/GEM. Since both models underestimate the experimental results for neutron-production doubledifferential cross sections at 180° for 140-MeV proton incident on carbon, iron, and gold targets, it is concluded that it is necessary to allow a margin for uncertainty caused by the spallation models, which is a factor of two, in estimating the dose rate induced by neutron streaming through a beam duct.

Experimental toxicology: Issues of statistics, experimental design, and replication.

Science.gov (United States)

Briner, Wayne; Kirwan, Jeral

2017-01-01

The difficulty of replicating experiments has drawn considerable attention. Issues with replication occur for a variety of reasons ranging from experimental design to laboratory errors to inappropriate statistical analysis. Here we review a variety of guidelines for statistical analysis, design, and execution of experiments in toxicology. In general, replication can be improved by using hypothesis driven experiments with adequate sample sizes, randomization, and blind data collection techniques. Copyright © 2016 Elsevier B.V. All rights reserved.

Mixing characterisation of full-scale membrane bioreactors: CFD modelling with experimental validation.

Science.gov (United States)

Brannock, M; Wang, Y; Leslie, G

2010-05-01

Membrane Bioreactors (MBRs) have been successfully used in aerobic biological wastewater treatment to solve the perennial problem of effective solids-liquid separation. The optimisation of MBRs requires knowledge of the membrane fouling, biokinetics and mixing. However, research has mainly concentrated on the fouling and biokinetics (Ng and Kim, 2007). Current methods of design for a desired flow regime within MBRs are largely based on assumptions (e.g. complete mixing of tanks) and empirical techniques (e.g. specific mixing energy). However, it is difficult to predict how sludge rheology and vessel design in full-scale installations affects hydrodynamics, hence overall performance. Computational Fluid Dynamics (CFD) provides a method for prediction of how vessel features and mixing energy usage affect the hydrodynamics. In this study, a CFD model was developed which accounts for aeration, sludge rheology and geometry (i.e. bioreactor and membrane module). This MBR CFD model was then applied to two full-scale MBRs and was successfully validated against experimental results. The effect of sludge settling and rheology was found to have a minimal impact on the bulk mixing (i.e. the residence time distribution).

Numerical simulation and experimental validation of coiled adiabatic capillary tubes

Energy Technology Data Exchange (ETDEWEB)

Garcia-Valladares, O. [Centro de Investigacion en Energia, Universidad Nacional Autonoma de Mexico (UNAM), Apdo. Postal 34, 62580 Temixco, Morelos (Mexico)

2007-04-15

The objective of this study is to extend and validate the model developed and presented in previous works [O. Garcia-Valladares, C.D. Perez-Segarra, A. Oliva, Numerical simulation of capillary tube expansion devices behaviour with pure and mixed refrigerants considering metastable region. Part I: mathematical formulation and numerical model, Applied Thermal Engineering 22 (2) (2002) 173-182; O. Garcia-Valladares, C.D. Perez-Segarra, A. Oliva, Numerical simulation of capillary tube expansion devices behaviour with pure and mixed refrigerants considering metastable region. Part II: experimental validation and parametric studies, Applied Thermal Engineering 22 (4) (2002) 379-391] to coiled adiabatic capillary tube expansion devices working with pure and mixed refrigerants. The discretized governing equations are coupled using an implicit step by step method. A special treatment has been implemented in order to consider transitions (subcooled liquid region, metastable liquid region, metastable two-phase region and equilibrium two-phase region). All the flow variables (enthalpies, temperatures, pressures, vapor qualities, velocities, heat fluxes, etc.) together with the thermophysical properties are evaluated at each point of the grid in which the domain is discretized. The numerical model allows analysis of aspects such as geometry, type of fluid (pure substances and mixtures), critical or non-critical flow conditions, metastable regions, and transient aspects. Comparison of the numerical simulation with a wide range of experimental data presented in the technical literature will be shown in the present article in order to validate the model developed. (author)

Development of robust flexible OLED encapsulations using simulated estimations and experimental validations

International Nuclear Information System (INIS)

Lee, Chang-Chun; Shih, Yan-Shin; Wu, Chih-Sheng; Tsai, Chia-Hao; Yeh, Shu-Tang; Peng, Yi-Hao; Chen, Kuang-Jung

2012-01-01

This work analyses the overall stress/strain characteristic of flexible encapsulations with organic light-emitting diode (OLED) devices. A robust methodology composed of a mechanical model of multi-thin film under bending loads and related stress simulations based on nonlinear finite element analysis (FEA) is proposed, and validated to be more reliable compared with related experimental data. With various geometrical combinations of cover plate, stacked thin films and plastic substrate, the position of the neutral axis (NA) plate, which is regarded as a key design parameter to minimize stress impact for the concerned OLED devices, is acquired using the present methodology. The results point out that both the thickness and mechanical properties of the cover plate help in determining the NA location. In addition, several concave and convex radii are applied to examine the reliable mechanical tolerance and to provide an insight into the estimated reliability of foldable OLED encapsulations. (paper)

Time-oriented experimental design method to optimize hydrophilic matrix formulations with gelation kinetics and drug release profiles.

Science.gov (United States)

Shin, Sangmun; Choi, Du Hyung; Truong, Nguyen Khoa Viet; Kim, Nam Ah; Chu, Kyung Rok; Jeong, Seong Hoon

2011-04-04

A new experimental design methodology was developed by integrating the response surface methodology and the time series modeling. The major purposes were to identify significant factors in determining swelling and release rate from matrix tablets and their relative factor levels for optimizing the experimental responses. Properties of tablet swelling and drug release were assessed with ten factors and two default factors, a hydrophilic model drug (terazosin) and magnesium stearate, and compared with target values. The selected input control factors were arranged in a mixture simplex lattice design with 21 experimental runs. The obtained optimal settings for gelation were PEO, LH-11, Syloid, and Pharmacoat with weight ratios of 215.33 (88.50%), 5.68 (2.33%), 19.27 (7.92%), and 3.04 (1.25%), respectively. The optimal settings for drug release were PEO and citric acid with weight ratios of 191.99 (78.91%) and 51.32 (21.09%), respectively. Based on the results of matrix swelling and drug release, the optimal solutions, target values, and validation experiment results over time were similar and showed consistent patterns with very small biases. The experimental design methodology could be a very promising experimental design method to obtain maximum information with limited time and resources. It could also be very useful in formulation studies by providing a systematic and reliable screening method to characterize significant factors in the sustained release matrix tablet. Copyright © 2011 Elsevier B.V. All rights reserved.

Preliminary experimentally-validated forced and mixed convection computational simulations of the Rotatable Buoyancy Tunnel

International Nuclear Information System (INIS)

Clifford, Corey E.; Kimber, Mark L.

2015-01-01

Although computational fluid dynamics (CFD) has not been directly utilized to perform safety analyses of nuclear reactors in the United States, several vendors are considering adopting commercial numerical packages for current and future projects. To ensure the accuracy of these computational models, it is imperative to validate the assumptions and approximations built into commercial CFD codes against physical data from flows analogous to those in modern nuclear reactors. To this end, researchers at Utah State University (USU) have constructed the Rotatable Buoyancy Tunnel (RoBuT) test facility, which is designed to provide flow and thermal validation data for CFD simulations of forced and mixed convection scenarios. In order to evaluate the ability of current CFD codes to capture the complex physics associated with these types of flows, a computational model of the RoBuT test facility is created using the ANSYS Fluent commercial CFD code. The numerical RoBuT model is analyzed at identical conditions to several experimental trials undertaken at USU. Each experiment is reconstructed numerically and evaluated with the second-order Reynolds stress model (RSM). Two different thermal boundary conditions at the heated surface of the RoBuT test section are investigated: constant temperature (isothermal) and constant surface heat flux (isoflux). Additionally, the fluid velocity at the inlet of the test section is varied in an effort to modify the relative importance of natural convection heat transfer from the heated wall of the RoBuT. Mean velocity, both in the streamwise and transverse directions, as well as components of the Reynolds stress tensor at three points downstream of the RoBuT test section inlet are compared to results obtained from experimental trials. Early computational results obtained from this research initiative are in good agreement with experimental data obtained from the RoBuT facility and both the experimental data and numerical method can be used

Design and validation of an MR-conditional robot for transcranial focused ultrasound surgery in infants

Energy Technology Data Exchange (ETDEWEB)

Price, Karl D., E-mail: karl.price@sickkids.ca [Centre for Image Guided Innovation and Therapeutic Intervention, The Hospital for Sick Children, Toronto, Ontario M5G 1X8 (Canada); The Department of Mechanical Engineering, The University of Toronto, Toronto, Ontario M5S 3G8 (Canada); Sin, Vivian W. [Centre for Image Guided Innovation and Therapeutic Intervention, The Hospital for Sick Children, Toronto, Ontario M5G 1X8 (Canada); Mougenot, Charles [Philips Healthcare Canada, Markham, Ontario L6C 2S3 (Canada); Pichardo, Samuel [Electrical Engineering, Lakehead University, Thunder Bay, Ontario P7B 5E1 (Canada); Looi, Thomas [Centre for Image Guided Innovation and Therapeutic Intervention, The Hospital for Sick Children, Toronto, Ontario M5G 1X8 (Canada); The Institute of Biomaterials and Biomedical Engineering, The University of Toronto, Toronto, Ontario M5G 3G9 (Canada); Waspe, Adam C. [Centre for Image Guided Innovation and Therapeutic Intervention, The Hospital for Sick Children, Toronto, Ontario M5G 1X8 (Canada); Department of Medical Imaging, The University of Toronto, Toronto, Ontario M5T 1W7 (Canada); Drake, James M. [Centre for Image Guided Innovation and Therapeutic Intervention, The Hospital for Sick Children, Toronto, Ontario M5G 1X8 (Canada); Department of Neurosurgery, The University of Toronto, Toronto, Ontario M5S 1A1 (Canada); The Institute of Biomaterials and Biomedical Engineering, The University of Toronto, Toronto, Ontario M5G 3G9 (Canada)

2016-09-15

Purpose: Current treatment of intraventricular hemorrhage (IVH) involves cerebral shunt placement or an invasive brain surgery. Magnetic resonance-guided focused ultrasound (MRgFUS) applied to the brains of pediatric patients presents an opportunity to treat IVH in a noninvasive manner, termed “incision-less surgery.” Current clinical and research focused ultrasound systems lack the capability to perform neonatal transcranial surgeries due to either range of motion or dexterity requirements. A novel robotic system is proposed to position a focused ultrasound transducer accurately above the head of a neonatal patient inside an MRI machine to deliver the therapy. Methods: A clinical Philips Sonalleve MRgFUS system was expanded to perform transcranial treatment. A five degree-of-freedom MR-conditional robot was designed and manufactured using MR compatible materials. The robot electronics and control were integrated into existing Philips electronics and software interfaces. The user commands the position of the robot with a graphical user interface, and is presented with real-time MR imaging of the patient throughout the surgery. The robot is validated through a series of experiments that characterize accuracy, signal-to-noise ratio degeneration of an MR image as a result of the robot, MR imaging artifacts generated by the robot, and the robot’s ability to operate in a representative surgical environment inside an MR machine. Results: Experimental results show the robot responds reliably within an MR environment, has achieved 0.59 ± 0.25 mm accuracy, does not produce severe MR-imaging artifacts, has a workspace providing sufficient coverage of a neonatal brain, and can manipulate a 5 kg payload. A full system demonstration shows these characteristics apply in an application environment. Conclusions: This paper presents a comprehensive look at the process of designing and validating a new robot from concept to implementation for use in an MR environment. An MR

Design and validation of an MR-conditional robot for transcranial focused ultrasound surgery in infants

International Nuclear Information System (INIS)

Price, Karl D.; Sin, Vivian W.; Mougenot, Charles; Pichardo, Samuel; Looi, Thomas; Waspe, Adam C.; Drake, James M.

2016-01-01

Purpose: Current treatment of intraventricular hemorrhage (IVH) involves cerebral shunt placement or an invasive brain surgery. Magnetic resonance-guided focused ultrasound (MRgFUS) applied to the brains of pediatric patients presents an opportunity to treat IVH in a noninvasive manner, termed “incision-less surgery.” Current clinical and research focused ultrasound systems lack the capability to perform neonatal transcranial surgeries due to either range of motion or dexterity requirements. A novel robotic system is proposed to position a focused ultrasound transducer accurately above the head of a neonatal patient inside an MRI machine to deliver the therapy. Methods: A clinical Philips Sonalleve MRgFUS system was expanded to perform transcranial treatment. A five degree-of-freedom MR-conditional robot was designed and manufactured using MR compatible materials. The robot electronics and control were integrated into existing Philips electronics and software interfaces. The user commands the position of the robot with a graphical user interface, and is presented with real-time MR imaging of the patient throughout the surgery. The robot is validated through a series of experiments that characterize accuracy, signal-to-noise ratio degeneration of an MR image as a result of the robot, MR imaging artifacts generated by the robot, and the robot’s ability to operate in a representative surgical environment inside an MR machine. Results: Experimental results show the robot responds reliably within an MR environment, has achieved 0.59 ± 0.25 mm accuracy, does not produce severe MR-imaging artifacts, has a workspace providing sufficient coverage of a neonatal brain, and can manipulate a 5 kg payload. A full system demonstration shows these characteristics apply in an application environment. Conclusions: This paper presents a comprehensive look at the process of designing and validating a new robot from concept to implementation for use in an MR environment. An MR

Experimental validation of lead cross sections for scale and MCNP

International Nuclear Information System (INIS)

Henrikson, D.J.

1995-01-01

Moving spent nuclear fuel between facilities often requires the use of lead-shielded casks. Criticality safety that is based upon calculations requires experimental validation of the fuel matrix and lead cross section libraries. A series of critical experiments using a high-enriched uranium-aluminum fuel element with a variety of reflectors, including lead, has been identified. Twenty-one configurations were evaluated in this study. The fuel element was modelled for KENO V.a and MCNP 4a using various cross section sets. The experiments addressed in this report can be used to validate lead-reflected calculations. Factors influencing calculated k eff which require further study include diameters of styrofoam inserts and homogenization

An Effective Experimental Optimization Method for Wireless Power Transfer System Design Using Frequency Domain Measurement

Directory of Open Access Journals (Sweden)

Sangyeong Jeong

2017-10-01

Full Text Available This paper proposes an experimental optimization method for a wireless power transfer (WPT system. The power transfer characteristics of a WPT system with arbitrary loads and various types of coupling and compensation networks can be extracted by frequency domain measurements. The various performance parameters of the WPT system, such as input real/imaginary/apparent power, power factor, efficiency, output power and voltage gain, can be accurately extracted in a frequency domain by a single passive measurement. Subsequently, the design parameters can be efficiently tuned by separating the overall design steps into two parts. The extracted performance parameters of the WPT system were validated with time-domain experiments.

CPV cells cooling system based on submerged jet impingement: CFD modeling and experimental validation

Science.gov (United States)

Montorfano, Davide; Gaetano, Antonio; Barbato, Maurizio C.; Ambrosetti, Gianluca; Pedretti, Andrea

2014-09-01

Concentrating photovoltaic (CPV) cells offer higher efficiencies with regard to the PV ones and allow to strongly reduce the overall solar cell area. However, to operate correctly and exploit their advantages, their temperature has to be kept low and as uniform as possible and the cooling circuit pressure drops need to be limited. In this work an impingement water jet cooling system specifically designed for an industrial HCPV receiver is studied. Through the literature and by means of accurate computational fluid dynamics (CFD) simulations, the nozzle to plate distance, the number of jets and the nozzle pitch, i.e. the distance between adjacent jets, were optimized. Afterwards, extensive experimental tests were performed to validate pressure drops and cooling power simulation results.

Fault-tolerant clock synchronization validation methodology. [in computer systems

Science.gov (United States)

Butler, Ricky W.; Palumbo, Daniel L.; Johnson, Sally C.

1987-01-01

A validation method for the synchronization subsystem of a fault-tolerant computer system is presented. The high reliability requirement of flight-crucial systems precludes the use of most traditional validation methods. The method presented utilizes formal design proof to uncover design and coding errors and experimentation to validate the assumptions of the design proof. The experimental method is described and illustrated by validating the clock synchronization system of the Software Implemented Fault Tolerance computer. The design proof of the algorithm includes a theorem that defines the maximum skew between any two nonfaulty clocks in the system in terms of specific system parameters. Most of these parameters are deterministic. One crucial parameter is the upper bound on the clock read error, which is stochastic. The probability that this upper bound is exceeded is calculated from data obtained by the measurement of system parameters. This probability is then included in a detailed reliability analysis of the system.

Verification and validation benchmarks.

Energy Technology Data Exchange (ETDEWEB)

Oberkampf, William Louis; Trucano, Timothy Guy

2007-02-01

Verification and validation (V&V) are the primary means to assess the accuracy and reliability of computational simulations. V&V methods and procedures have fundamentally improved the credibility of simulations in several high-consequence fields, such as nuclear reactor safety, underground nuclear waste storage, and nuclear weapon safety. Although the terminology is not uniform across engineering disciplines, code verification deals with assessing the reliability of the software coding, and solution verification deals with assessing the numerical accuracy of the solution to a computational model. Validation addresses the physics modeling accuracy of a computational simulation by comparing the computational results with experimental data. Code verification benchmarks and validation benchmarks have been constructed for a number of years in every field of computational simulation. However, no comprehensive guidelines have been proposed for the construction and use of V&V benchmarks. For example, the field of nuclear reactor safety has not focused on code verification benchmarks, but it has placed great emphasis on developing validation benchmarks. Many of these validation benchmarks are closely related to the operations of actual reactors at near-safety-critical conditions, as opposed to being more fundamental-physics benchmarks. This paper presents recommendations for the effective design and use of code verification benchmarks based on manufactured solutions, classical analytical solutions, and highly accurate numerical solutions. In addition, this paper presents recommendations for the design and use of validation benchmarks, highlighting the careful design of building-block experiments, the estimation of experimental measurement uncertainty for both inputs and outputs to the code, validation metrics, and the role of model calibration in validation. It is argued that the understanding of predictive capability of a computational model is built on the level of

Design of an intermediate-scale experiment to validate unsaturated- zone transport models

International Nuclear Information System (INIS)

Siegel, M.D.; Hopkins, P.L.; Glass, R.J.; Ward, D.B.

1991-01-01

An intermediate-scale experiment is being carried out to evaluate instrumentation and models that might be used for transport-model validation for the Yucca Mountain Site Characterization Project. The experimental test bed is a 6-m high x 3-m diameter caisson filled with quartz sand with a sorbing layer at an intermediate depth. The experiment involves the detection and prediction of the migration of fluid and tracers through an unsaturated porous medium. Pre-test design requires estimation of physical properties of the porous medium such as the relative permeability, saturation/pressure relations, porosity, and saturated hydraulic conductivity as well as geochemical properties such as surface complexation constants and empircial K d 'S. The pre-test characterization data will be used as input to several computer codes to predict the fluid flow and tracer migration. These include a coupled chemical-reaction/transport model, a stochastic model, and a deterministic model using retardation factors. The calculations will be completed prior to elution of the tracers, providing a basis for validation by comparing the predictions to observed moisture and tracer behavior

Quasi-experimental study designs series-paper 4: uses and value.

Science.gov (United States)

Bärnighausen, Till; Tugwell, Peter; Røttingen, John-Arne; Shemilt, Ian; Rockers, Peter; Geldsetzer, Pascal; Lavis, John; Grimshaw, Jeremy; Daniels, Karen; Brown, Annette; Bor, Jacob; Tanner, Jeffery; Rashidian, Arash; Barreto, Mauricio; Vollmer, Sebastian; Atun, Rifat

2017-09-01

Quasi-experimental studies are increasingly used to establish causal relationships in epidemiology and health systems research. Quasi-experimental studies offer important opportunities to increase and improve evidence on causal effects: (1) they can generate causal evidence when randomized controlled trials are impossible; (2) they typically generate causal evidence with a high degree of external validity; (3) they avoid the threats to internal validity that arise when participants in nonblinded experiments change their behavior in response to the experimental assignment to either intervention or control arm (such as compensatory rivalry or resentful demoralization); (4) they are often well suited to generate causal evidence on long-term health outcomes of an intervention, as well as nonhealth outcomes such as economic and social consequences; and (5) they can often generate evidence faster and at lower cost than experiments and other intervention studies. Copyright © 2017 Elsevier Inc. All rights reserved.

The turbulent viscosity models and their experimental validation; Les modeles de viscosite turbulente et leur validation experimentale

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

This workshop on turbulent viscosity models and on their experimental validation was organized by the `convection` section of the French society of thermal engineers. From the 9 papers presented during this workshop, 8 deal with the modeling of turbulent flows inside combustion chambers, turbo-machineries or in other energy-related applications, and have been selected for ETDE. (J.S.)

76 FR 81991 - National Spectrum Sharing Research Experimentation, Validation, Verification, Demonstration and...

Science.gov (United States)

2011-12-29

... NATIONAL SCIENCE FOUNDATION National Spectrum Sharing Research Experimentation, Validation... requirements of national level spectrum research, development, demonstration, and field trial facilities... to determine the optimal way to manage and use the radio spectrum. During Workshop I held at Boulder...

Bayesian optimal experimental design for the Shock-tube experiment

International Nuclear Information System (INIS)

Terejanu, G; Bryant, C M; Miki, K

2013-01-01

The sequential optimal experimental design formulated as an information-theoretic sensitivity analysis is applied to the ignition delay problem using real experimental. The optimal design is obtained by maximizing the statistical dependence between the model parameters and observables, which is quantified in this study using mutual information. This is naturally posed in the Bayesian framework. The study shows that by monitoring the information gain after each measurement update, one can design a stopping criteria for the experimental process which gives a minimal set of experiments to efficiently learn the Arrhenius parameters.

Design, Development & Functional Validation of Magnets system in support of 42 GHz Gyrotron in India

Directory of Open Access Journals (Sweden)

Pradhan S.

2017-01-01

Full Text Available A multi institutional initiative is underway towards the development of 42 GHz, 200 kW gyrotron system in India under the frame work of Department of Science and Technology, Government of India. Indigenous realization comprising of design, fabrication, prototypes and functional validations of an appropriate Magnet System is one of the primary technological objective of these initiatives. The 42 GHz gyrotron magnet system comprises of a warm gun magnet, a NbTi/Cu based high homogenous superconducting cavity magnet and three warm collector magnets. The superconducting cavity magnet has been housed inside a low loss cryostat. The magnet system has been designed in accordance with gyrotron physics and engineering considerations respecting highly homogenous spatial field profile as well as maintaining steep gradient as per the compression and velocity ratios between the emission and resonator regions. The designed magnet system further ensures the co-linearity of the magnetic axis with that of the beam axis with custom winding techniques apart from a smooth collection of beam with the collector magnet profiles. The designed magnets have been wound after several R & D validations. The superconducting magnet has been housed inside a low loss designed cryostat with in-built radial and axial alignment flexibilities to certain extent. The cryostat further houses liquid helium port, liquid nitrogen ports, current communication ports, ports for monitoring helium level and other instrumentations apart from over-pressure safety intensive burst disks etc. The entire magnet system comprising of warm and superconducting magnets has been installed and integrated in the Gyrotron test set-up. The magnet system has been aligned in both warm and when the superconducting cavity magnet is cold. The integrated geometric axes have been experimentally ensured as well as the field profiles have been measured with the magnets being charged. Under experimental conditions

Development of human factors experimental evaluation techniques - Human factors design and evaluation of the main control room of atomic power plants using visual display terminals

Energy Technology Data Exchange (ETDEWEB)

Han, Sung Ho; Chung, Min Kyun; Choi, Kyung Lim; Song, Young Woong; Eoh, Hong Joon; Lee, In Suk; Kim, Bom Soo; Yeo, Yun Shin; Lee, Haeo Sun [Pohang University of Science and Technology, Pohang (Korea, Republic of)

1995-07-01

This study was conducted to build a prototype of the operator interface on a visual display terminal, and to provide a framework for using and applying prototyping techniques. A typical subsystem of an MCR was prototyped and validated by operator testing. Lessons learned during the development as well as prototyping techniques were described in this report for an efficient development. In addition, human factors experimental plans were surveyed and summarized for evaluating new design alternatives as well as the current design of the operator interface. The major results of this study are listed as follow: A method for designing an operator interface prototype on a VDT, A prototype of the operator interface of a typical subsystem, Guidelines for applying prototyping techniques, Characteristics and major considerations of experimental plans, Guidelines for applying prototyping techniques, Characteristics and major considerations of experimental plans, Guidelines for analyzing experimental data, A paradigm for human factors experimentation including experimental designs, procedures, and data analyses. 27 refs., 60 tabs., 47 figs. (author)

A PFC3D-based numerical simulation of cutting load for lunar rock simulant and experimental validation

Science.gov (United States)

Li, Peng; Jiang, Shengyuan; Tang, Dewei; Xu, Bo

2017-05-01

For sake of striking a balance between the need of drilling efficiency and the constrains of power budget on the moon, the penetrations per revolution of drill bit are generally limited in the range around 0.1 mm, and besides the geometric angle of the cutting blade need to be well designed. This paper introduces a simulation approach based on PFC3D (particle flow code 3 dimensions) for analyzing the cutting load feature on lunar rock simulant, which is derived from different geometric-angle blades with a small cutting depth. The mean values of the cutting force of five blades in the survey region (four on the boundary points and one on the center point) are selected as the macroscopic responses of model. The method of experimental design which includes Plackett-Burman (PB) design and central composite design (CCD) method is adopted in the matching procedure of microparameters in PFC model. Using the optimization method of enumeration, the optimum set of microparameters is acquired. Then, the experimental validation is implemented by using other twenty-five blades with different geometric angles, and the results from both simulations and laboratory tests give fair agreements. Additionally, the rock breaking process cut by different blades are quantified from simulation analysis. This research provides the theoretical support for the refinement of the rock cutting load prediction and the geometric design of cutting blade on the drill bit.

On the construction of experimental designs for a given task by jointly optimizing several quality criteria: Pareto-optimal experimental designs.

Science.gov (United States)

Sánchez, M S; Sarabia, L A; Ortiz, M C

2012-11-19

Experimental designs for a given task should be selected on the base of the problem being solved and of some criteria that measure their quality. There are several such criteria because there are several aspects to be taken into account when making a choice. The most used criteria are probably the so-called alphabetical optimality criteria (for example, the A-, E-, and D-criteria related to the joint estimation of the coefficients, or the I- and G-criteria related to the prediction variance). Selecting a proper design to solve a problem implies finding a balance among these several criteria that measure the performance of the design in different aspects. Technically this is a problem of multi-criteria optimization, which can be tackled from different views. The approach presented here addresses the problem in its real vector nature, so that ad hoc experimental designs are generated with an algorithm based on evolutionary algorithms to find the Pareto-optimal front. There is not theoretical limit to the number of criteria that can be studied and, contrary to other approaches, no just one experimental design is computed but a set of experimental designs all of them with the property of being Pareto-optimal in the criteria needed by the user. Besides, the use of an evolutionary algorithm makes it possible to search in both continuous and discrete domains and avoid the need of having a set of candidate points, usual in exchange algorithms. Copyright © 2012 Elsevier B.V. All rights reserved.

Spacecraft early design validation using formal methods

International Nuclear Information System (INIS)

Bozzano, Marco; Cimatti, Alessandro; Katoen, Joost-Pieter; Katsaros, Panagiotis; Mokos, Konstantinos; Nguyen, Viet Yen; Noll, Thomas; Postma, Bart; Roveri, Marco

2014-01-01

The size and complexity of software in spacecraft is increasing exponentially, and this trend complicates its validation within the context of the overall spacecraft system. Current validation methods are labor-intensive as they rely on manual analysis, review and inspection. For future space missions, we developed – with challenging requirements from the European space industry – a novel modeling language and toolset for a (semi-)automated validation approach. Our modeling language is a dialect of AADL and enables engineers to express the system, the software, and their reliability aspects. The COMPASS toolset utilizes state-of-the-art model checking techniques, both qualitative and probabilistic, for the analysis of requirements related to functional correctness, safety, dependability and performance. Several pilot projects have been performed by industry, with two of them having focused on the system-level of a satellite platform in development. Our efforts resulted in a significant advancement of validating spacecraft designs from several perspectives, using a single integrated system model. The associated technology readiness level increased from level 1 (basic concepts and ideas) to early level 4 (laboratory-tested)

Ice condenser experimental plan

International Nuclear Information System (INIS)

Kannberg, L.D.; Piepel, G.F.; Owczarski, P.C.; Liebetrau, A.M.

1986-01-01

An experimental plan is being developed to validate the computer code ICEDF. The code was developed to estimate the extent of aerosol retention in the ice compartments of pressurized water reactor ice condenser containment systems during severe accidents. The development of the experimental plan began with review of available information on the conditions under which the code will be applied. Computer-generated estimates of thermohydraulic and aerosol conditions entering the ice condenser were evaluated and along with other information, used to generate design criteria. The design criteria have been used for preliminary test assembly design and for generation of statistical test designs. Consideration of the phenomena to be evaluated in the testing program, as well as equipment and measurement limitations, have led to changes in the design criteria and to subsequent changes in the test assembly design and statistical test design. The overall strategy in developing the experimental plan includes iterative generation and evaluation of candidate test designs using computer codes for statistical test design and ICEDF for estimation of experimental results. Estimates of experimental variability made prior to actual testing will be verified by replicate testing at preselected design points

Validation of the newborn larynx modeling with aerodynamical experimental data.

Science.gov (United States)

Nicollas, R; Giordano, J; Garrel, R; Medale, M; Caminat, P; Giovanni, A; Ouaknine, M; Triglia, J M

2009-06-01

Many authors have studied adult's larynx modelization, but the mechanisms of newborn's voice production have very rarely been investigated. After validating a numerical model with acoustic data, studies were performed on larynges of human fetuses in order to validate this model with aerodynamical experiments. Anatomical measurements were performed and a simplified numerical model was built using Fluent((R)) with the vocal folds in phonatory position. The results obtained are in good agreement with those obtained by laser Doppler velocimetry (LDV) and high-frame rate particle image velocimetry (HFR-PIV), on an experimental bench with excised human fetus larynges. It appears that computing with first cry physiological parameters leads to a model which is close to those obtained in experiments with real organs.

Acting like a physicist: Student approach study to experimental design

Science.gov (United States)

Karelina, Anna; Etkina, Eugenia

2007-12-01

National studies of science education have unanimously concluded that preparing our students for the demands of the 21st century workplace is one of the major goals. This paper describes a study of student activities in introductory college physics labs, which were designed to help students acquire abilities that are valuable in the workplace. In these labs [called Investigative Science Learning Environment (ISLE) labs], students design their own experiments. Our previous studies have shown that students in these labs acquire scientific abilities such as the ability to design an experiment to solve a problem, the ability to collect and analyze data, the ability to evaluate assumptions and uncertainties, and the ability to communicate. These studies mostly concentrated on analyzing students’ writing, evaluated by specially designed scientific ability rubrics. Recently, we started to study whether the ISLE labs make students not only write like scientists but also engage in discussions and act like scientists while doing the labs. For example, do students plan an experiment, validate assumptions, evaluate results, and revise the experiment if necessary? A brief report of some of our findings that came from monitoring students’ activity during ISLE and nondesign labs was presented in the Physics Education Research Conference Proceedings. We found differences in student behavior and discussions that indicated that ISLE labs do in fact encourage a scientistlike approach to experimental design and promote high-quality discussions. This paper presents a full description of the study.

Acting like a physicist: Student approach study to experimental design

Directory of Open Access Journals (Sweden)

Anna Karelina

2007-10-01

Full Text Available National studies of science education have unanimously concluded that preparing our students for the demands of the 21st century workplace is one of the major goals. This paper describes a study of student activities in introductory college physics labs, which were designed to help students acquire abilities that are valuable in the workplace. In these labs [called Investigative Science Learning Environment (ISLE labs], students design their own experiments. Our previous studies have shown that students in these labs acquire scientific abilities such as the ability to design an experiment to solve a problem, the ability to collect and analyze data, the ability to evaluate assumptions and uncertainties, and the ability to communicate. These studies mostly concentrated on analyzing students’ writing, evaluated by specially designed scientific ability rubrics. Recently, we started to study whether the ISLE labs make students not only write like scientists but also engage in discussions and act like scientists while doing the labs. For example, do students plan an experiment, validate assumptions, evaluate results, and revise the experiment if necessary? A brief report of some of our findings that came from monitoring students’ activity during ISLE and nondesign labs was presented in the Physics Education Research Conference Proceedings. We found differences in student behavior and discussions that indicated that ISLE labs do in fact encourage a scientistlike approach to experimental design and promote high-quality discussions. This paper presents a full description of the study.

Experimental Validation of Topology Optimization for RF MEMS Capacitive Switch Design

DEFF Research Database (Denmark)

Philippine, Mandy Axelle; Zareie, Hosein; Sigmund, Ole

2013-01-01

In this paper, we present 30 distinct RF MEMS capacitive switch designs that are the product of topology optimizations that control key mechanical properties such as stiffness, response to intrinsic stress gradients, and temperature sensitivity. The designs were evaluated with high-accuracy simul...

Design and validation of general biology learning program based on scientific inquiry skills

Science.gov (United States)

Cahyani, R.; Mardiana, D.; Noviantoro, N.

2018-03-01

Scientific inquiry is highly recommended to teach science. The reality in the schools and colleges is that many educators still have not implemented inquiry learning because of their lack of understanding. The study aims to1) analyze students’ difficulties in learning General Biology, 2) design General Biology learning program based on multimedia-assisted scientific inquiry learning, and 3) validate the proposed design. The method used was Research and Development. The subjects of the study were 27 pre-service students of general elementary school/Islamic elementary schools. The workflow of program design includes identifying learning difficulties of General Biology, designing course programs, and designing instruments and assessment rubrics. The program design is made for four lecture sessions. Validation of all learning tools were performed by expert judge. The results showed that: 1) there are some problems identified in General Biology lectures; 2) the designed products include learning programs, multimedia characteristics, worksheet characteristics, and, scientific attitudes; and 3) expert validation shows that all program designs are valid and can be used with minor revisions. The first section in your paper.

Electromagnetic scattering problems -Numerical issues and new experimental approaches of validation

Energy Technology Data Exchange (ETDEWEB)

Geise, Robert; Neubauer, Bjoern; Zimmer, Georg [University of Braunschweig, Institute for Electromagnetic Compatibility, Schleinitzstrasse 23, 38106 Braunschweig (Germany)

2015-03-10

Electromagnetic scattering problems, thus the question how radiated energy spreads when impinging on an object, are an essential part of wave propagation. Though the Maxwell’s differential equations as starting point, are actually quite simple,the integral formulation of an object’s boundary conditions, respectively the solution for unknown induced currents can only be solved numerically in most cases.As a timely topic of practical importance the scattering of rotating wind turbines is discussed, the numerical description of which is still based on rigorous approximations with yet unspecified accuracy. In this context the issue of validating numerical solutions is addressed, both with reference simulations but in particular with the experimental approach of scaled measurements. For the latter the idea of an incremental validation is proposed allowing a step by step validation of required new mathematical models in scattering theory.

Physical validation issue of the NEPTUNE two-phase modelling: validation plan to be adopted, experimental programs to be set up and associated instrumentation techniques developed

International Nuclear Information System (INIS)

Pierre Peturaud; Eric Hervieu

2005-01-01

Full text of publication follows: A long-term joint development program for the next generation of nuclear reactors simulation tools has been launched in 2001 by EDF (Electricite de France) and CEA (Commissariat a l'Energie Atomique). The NEPTUNE Project constitutes the Thermal-Hydraulics part of this comprehensive program. Along with the underway development of this new two-phase flow software platform, the physical validation of the involved modelling is a crucial issue, whatever the modelling scale is, and the present paper deals with this issue. After a brief recall about the NEPTUNE platform, the general validation strategy to be adopted is first of all clarified by means of three major features: (i) physical validation in close connection with the concerned industrial applications, (ii) involving (as far as possible) a two-step process successively focusing on dominant separate models and assessing the whole modelling capability, (iii) thanks to the use of relevant data with respect to the validation aims. Based on this general validation process, a four-step generic work approach has been defined; it includes: (i) a thorough analysis of the concerned industrial applications to identify the key physical phenomena involved and associated dominant basic models, (ii) an assessment of these models against the available validation pieces of information, to specify the additional validation needs and define dedicated validation plans, (iii) an inventory and assessment of existing validation data (with respect to the requirements specified in the previous task) to identify the actual needs for new validation data, (iv) the specification of the new experimental programs to be set up to provide the needed new data. This work approach has been applied to the NEPTUNE software, focusing on 8 high priority industrial applications, and it has resulted in the definition of (i) the validation plan and experimental programs to be set up for the open medium 3D modelling

Validity test of design calculations of a PGNAA setup

International Nuclear Information System (INIS)

Naqvi, A.A.; Garwan, M.A.

2004-01-01

A rectangular moderator has been designed for the prompt gamma ray neutron activation analysis (PGNAA) setup at King Fahd University of Petroleum and Minerals (KFUPM) to analyze Portland cement samples. The design of the moderator assembly was obtained using Monte Carlo calculations. The design calculations of the new rectangular moderator of the KFUPM PGNAA setup have been verified experimentally through prompt gamma ray yield measurement as a function of the front moderator thickness. In this study the yield of the 3.54 and 4.94 MeV prompt gamma rays from silicon in a soil sample was measured as a function of thickness of the front moderator of the rectangular moderator. The experimental results were compared with the results of the Monte Carlo simulations. A good agreement has been achieved between the experimental results and the results of the calculations. The experimental results have provided useful information about the PGNAA setup performance, neutron moderation, and gamma ray attenuation in the PGNAA sample

Design and Experimental Validation of Thick Airfoils for Large Wind Turbines

DEFF Research Database (Denmark)

Hrgovan, Iva; Shen, Wen Zhong; Zhu, Wei Jun

2015-01-01

In this chapter, two new airfoils with thickness to chord ratios of 30 and 36 % are presented, which were designed with an objective of good aerodynamic and structural features. Airfoil design is based on a direct method using shape perturbation function. The optimization algorithm is coupled wit...

Modeling, design and experimental validation of a small-sized magnetic gear

NARCIS (Netherlands)

Zanis, R.; Borisavljevic, A.; Jansen, J.W.; Lomonova, E.A.

2013-01-01

A magnetostatic analytical model is created to analyze and design a small-sized magnetic gear for a robotic application. Through a parameter variation study, it is found that the inner rotor magnet height is highly influential to the torque, and based on which, the design is performed. Several

Experimental Study of the Twin Turbulent Water Jets Using Laser Doppler Anemometry for Validating Numerical Models

International Nuclear Information System (INIS)

Wang Huhu; Lee Saya; Hassan, Yassin A.; Ruggles, Arthur E.

2014-01-01

The design of next generation (Gen. IV) high-temperature nuclear reactors including gas-cooled and sodium-cooled ones involves massive numerical works especially the Computational Fluid Dynamics (CFD) simulations. The high cost of large-scale experiments and the inherent uncertainties existing in the turbulent models and wall functions of any CFD codes solving Reynolds-averaged Navier-Stokes (RANS) equations necessitate the high-spacial experimental data sets for benchmarking the simulation results. In Gen. IV conceptual reactors, the high- temperature flows mix in the upper plenum before entering the secondary cooling system. The mixing condition should be accurately estimated and fully understood as it is related to the thermal stresses induced in the upper plenum and the magnitudes of output power oscillations due to any changes of primary coolant temperature. The purpose of this study is to use Laser Doppler Anemometry (LDA) technique to measure the flow field of two submerged parallel jets issuing from two rectangular channels. The LDA data sets can be used to validate the corresponding simulation results. The jets studied in this work were at room temperature. The turbulent characteristics including the distributions of mean velocities, turbulence intensities, Reynolds stresses were studied. Uncertainty analysis was also performed to study the errors involved in this experiment. The experimental results in this work are valid for benchmarking any steady-state numerical simulations using turbulence models to solve RANS equations. (author)

A DIFFERENT APPROACH IN OPTIMUM DESIGN PROCESS AND FEA VALIDATION OF LOW-SPEED MULTI-PHASE IPMSMS

Directory of Open Access Journals (Sweden)

seyed asghar gholamian

2017-05-01

Full Text Available Magnets placement effects on permanent magnet motors performance, because of its different magnetic flux density distribution. Therefore, different types of magnet placement should be examined experimentally or by valid simulations. In this paper, first, an interior permanent magnet synchronous motor (IPMSM called spoke type with specifications related to the propulsion of ships is designed and then optimized by ant colony algorithm to increase the torque-to-volume ratio. The design procedure and its formulas presented as simple as possible. Then, to verify the optimization results of the optimized motor, a Two-dimensional finite element analysis (FEA is done. Also in this analyze the core and the slot saturation was studied.

Experimental Study and Computational Simulations of Key Pebble Bed Thermo-mechanics Issues for Design and Safety

Energy Technology Data Exchange (ETDEWEB)

Tokuhiro, Akira; Potirniche, Gabriel; Cogliati, Joshua; Ougouag, Abderrafi

2014-07-08

An experimental and computational study, consisting of modeling and simulation (M&S), of key thermal-mechanical issues affecting the design and safety of pebble-bed (PB) reactors was conducted. The objective was to broaden understanding and experimentally validate thermal-mechanic phenomena of nuclear grade graphite, specifically, spheres in frictional contact as anticipated in the bed under reactor relevant pressures and temperatures. The contact generates graphite dust particulates that can subsequently be transported into the flowing gaseous coolent. Under postulated depressurization transients and with the potential for leaked fission products to be adsorbed onto graphite 'dust', there is the potential for fission products to escape from the primary volume. This is a design safety concern. Furthermore, earlier safety assessment identified the distinct possibility for the dispersed dust to combust in contact with air if sufficient conditions are met. Both of these phenomena were noted as important to design review and containing uncertainty to warrant study. The team designed and conducted two separate effects tests to study and benchmark the potential dust-generation rate, as well as study the conditions under which a dust explosion may occure in a standardized, instrumented explosion chamber.

Design and validation of a comprehensive fecal incontinence questionnaire.

Science.gov (United States)

Macmillan, Alexandra K; Merrie, Arend E H; Marshall, Roger J; Parry, Bryan R

2008-10-01

Fecal incontinence can have a profound effect on quality of life. Its prevalence remains uncertain because of stigma, lack of consistent definition, and dearth of validated measures. This study was designed to develop a valid clinical and epidemiologic questionnaire, building on current literature and expertise. Patients and experts undertook face validity testing. Construct validity, criterion validity, and test-retest reliability was undertaken. Construct validity comprised factor analysis and internal consistency of the quality of life scale. The validity of known groups was tested against 77 control subjects by using regression models. Questionnaire results were compared with a stool diary for criterion validity. Test-retest reliability was calculated from repeated questionnaire completion. The questionnaire achieved good face validity. It was completed by 104 patients. The quality of life scale had four underlying traits (factor analysis) and high internal consistency (overall Cronbach alpha = 0.97). Patients and control subjects answered the questionnaire significantly differently (P validity testing. Criterion validity assessment found mean differences close to zero. Median reliability for the whole questionnaire was 0.79 (range, 0.35-1). This questionnaire compares favorably with other available instruments, although the interpretation of stool consistency requires further research. Its sensitivity to treatment still needs to be investigated.

CFD Code Validation against Stratified Air-Water Flow Experimental Data

International Nuclear Information System (INIS)

Terzuoli, F.; Galassi, M.C.; Mazzini, D.; D'Auria, F.

2008-01-01

Pressurized thermal shock (PTS) modelling has been identified as one of the most important industrial needs related to nuclear reactor safety. A severe PTS scenario limiting the reactor pressure vessel (RPV) lifetime is the cold water emergency core cooling (ECC) injection into the cold leg during a loss of coolant accident (LOCA). Since it represents a big challenge for numerical simulations, this scenario was selected within the European Platform for Nuclear Reactor Simulations (NURESIM) Integrated Project as a reference two-phase problem for computational fluid dynamics (CFDs) code validation. This paper presents a CFD analysis of a stratified air-water flow experimental investigation performed at the Institut de Mecanique des Fluides de Toulouse in 1985, which shares some common physical features with the ECC injection in PWR cold leg. Numerical simulations have been carried out with two commercial codes (Fluent and Ansys CFX), and a research code (NEPTUNE CFD). The aim of this work, carried out at the University of Pisa within the NURESIM IP, is to validate the free surface flow model implemented in the codes against experimental data, and to perform code-to-code benchmarking. Obtained results suggest the relevance of three-dimensional effects and stress the importance of a suitable interface drag modelling

CFD Code Validation against Stratified Air-Water Flow Experimental Data

Directory of Open Access Journals (Sweden)

F. Terzuoli

2008-01-01

Full Text Available Pressurized thermal shock (PTS modelling has been identified as one of the most important industrial needs related to nuclear reactor safety. A severe PTS scenario limiting the reactor pressure vessel (RPV lifetime is the cold water emergency core cooling (ECC injection into the cold leg during a loss of coolant accident (LOCA. Since it represents a big challenge for numerical simulations, this scenario was selected within the European Platform for Nuclear Reactor Simulations (NURESIM Integrated Project as a reference two-phase problem for computational fluid dynamics (CFDs code validation. This paper presents a CFD analysis of a stratified air-water flow experimental investigation performed at the Institut de Mécanique des Fluides de Toulouse in 1985, which shares some common physical features with the ECC injection in PWR cold leg. Numerical simulations have been carried out with two commercial codes (Fluent and Ansys CFX, and a research code (NEPTUNE CFD. The aim of this work, carried out at the University of Pisa within the NURESIM IP, is to validate the free surface flow model implemented in the codes against experimental data, and to perform code-to-code benchmarking. Obtained results suggest the relevance of three-dimensional effects and stress the importance of a suitable interface drag modelling.

Computational Fluid Dynamics Modeling of the Human Pulmonary Arteries with Experimental Validation.

Science.gov (United States)

Bordones, Alifer D; Leroux, Matthew; Kheyfets, Vitaly O; Wu, Yu-An; Chen, Chia-Yuan; Finol, Ender A

2018-05-21

Pulmonary hypertension (PH) is a chronic progressive disease characterized by elevated pulmonary arterial pressure, caused by an increase in pulmonary arterial impedance. Computational fluid dynamics (CFD) can be used to identify metrics representative of the stage of PH disease. However, experimental validation of CFD models is often not pursued due to the geometric complexity of the model or uncertainties in the reproduction of the required flow conditions. The goal of this work is to validate experimentally a CFD model of a pulmonary artery phantom using a particle image velocimetry (PIV) technique. Rapid prototyping was used for the construction of the patient-specific pulmonary geometry, derived from chest computed tomography angiography images. CFD simulations were performed with the pulmonary model with a Reynolds number matching those of the experiments. Flow rates, the velocity field, and shear stress distributions obtained with the CFD simulations were compared to their counterparts from the PIV flow visualization experiments. Computationally predicted flow rates were within 1% of the experimental measurements for three of the four branches of the CFD model. The mean velocities in four transversal planes of study were within 5.9 to 13.1% of the experimental mean velocities. Shear stresses were qualitatively similar between the two methods with some discrepancies in the regions of high velocity gradients. The fluid flow differences between the CFD model and the PIV phantom are attributed to experimental inaccuracies and the relative compliance of the phantom. This comparative analysis yielded valuable information on the accuracy of CFD predicted hemodynamics in pulmonary circulation models.

Design, experimental investigation and multi-objective optimization of a small-scale radial compressor for heat pump applications

Energy Technology Data Exchange (ETDEWEB)

Schiffmann, J. [Fischer Engineering Solutions AG, Birkenweg 3, CH-3360 Herzogenbuchsee (Switzerland); Favrat, D. [Ecole Polytechnique Federale de Lausanne, EPFL STI IGM LENI, Station 9, CH-1015 Lausanne (Switzerland)

2010-01-15

The main driver for small scale turbomachinery in domestic heat pumps is the potential for reaching higher efficiencies than volumetric compressors currently used and the potential for making the compressor oil-free, bearing a considerable advantage in the design of advanced multi-stage heat pump cycles. An appropriate turbocompressor for driving domestic heat pumps with a high temperature lift requires the ability to operate on a wide range of pressure ratios and mass flows, confronting the designer with the necessity of a compromise between range and efficiency. The present publication shows a possible way to deal with that difficulty, by coupling an appropriate modeling tool to a multi-objective optimizer. The optimizer manages to fit the compressor design into the possible specifications field while keeping the high efficiency on a wide operational range. The 1D-tool used for the compressor stage modeling has been validated by experimentally testing an initial impeller design. The excellent experimental results, the agreement with the model and the linking of the model to a multi-objective optimizer will allow to design radial compressor stages managing to fit the wide operational range of domestic heat pumps while keeping the high efficiency level. (author)

Research Methods in Healthcare Epidemiology and Antimicrobial Stewardship-Quasi-Experimental Designs.

Science.gov (United States)

Schweizer, Marin L; Braun, Barbara I; Milstone, Aaron M

2016-10-01

Quasi-experimental studies evaluate the association between an intervention and an outcome using experiments in which the intervention is not randomly assigned. Quasi-experimental studies are often used to evaluate rapid responses to outbreaks or other patient safety problems requiring prompt, nonrandomized interventions. Quasi-experimental studies can be categorized into 3 major types: interrupted time-series designs, designs with control groups, and designs without control groups. This methods paper highlights key considerations for quasi-experimental studies in healthcare epidemiology and antimicrobial stewardship, including study design and analytic approaches to avoid selection bias and other common pitfalls of quasi-experimental studies. Infect Control Hosp Epidemiol 2016;1-6.

Numerical modelling and experimental validation of hydrodynamics of an emulsion in an extraction column

International Nuclear Information System (INIS)

Paisant, Jean-Francois

2014-01-01

Industrial reprocessing of spent fuel is based on chemical separation processes by liquid-liquid extraction into pulsed column. The current context of sustainable development and acceptance of nuclear energy drive the industry to improve the efficiency of this process. Pulsed column efficiency is bound to the amount of available exchange surface, which depends on the geometrical parameters of the column and the operating conditions. A better design would improve the efficiency. In this context, the work presented in this manuscript revolves around physical and numerical modelling of the hydrodynamics of the emulsion coupled with the evolution of the interfacial area, as well as an experimental characterization of the quantities which describe the emulsion. The emulsion is modelled based on the work of D. LHUILLIER. It is an Eulerian approach which describes each phase as a continuous medium as well as the interface which is thought as a third phase moving continuously in the flow field. This thesis contributes to describe of the hydrodynamics of dispersed and continuous phases, in order to determine the slip velocity needed for the design. The written transport equation for interfacial area is based on the thesis of T. RANDRIAMANANTENA. The simulation of this physical model was performed using the method of finite elements (FEM) and implementation was carried out under the software CAST3M. The numerical simulation have shown their abilities to correctly reproduce the expected physical behaviour, in particular, they allow to obtain the slip velocity which is essential to the scale up. In a first experimental approach, the single phase flow has been studied in a pulsed column using particle image velocimetry (PIV), for different amplitude and frequency parameters. A method of synchronization between the recording and the pulsation cycle was used in order to achieve this study. The average behavior, for different regimes of pulsation, has been studied by this way. In

Objectives of Experimental Validation of Mechanical Equipment for BN-1200 Reactor Plant

International Nuclear Information System (INIS)

Timofeev, A.V.; Lyubimov, M.A.

2013-01-01

Conclusion: Fabricating and testing the pilot specimens of CRDMs, mockups of main elevator units, and cantilever refueling mechanism make it possible to validate their design. Positive testing results will make it possible to start the work on developing: • final designs of the elevator and cantilever refueling mechanism; • manufacturing design documentation on CRDM prototypes

Robust Bayesian Experimental Design for Conceptual Model Discrimination

Science.gov (United States)

Pham, H. V.; Tsai, F. T. C.

2015-12-01

A robust Bayesian optimal experimental design under uncertainty is presented to provide firm information for model discrimination, given the least number of pumping wells and observation wells. Firm information is the maximum information of a system can be guaranteed from an experimental design. The design is based on the Box-Hill expected entropy decrease (EED) before and after the experiment design and the Bayesian model averaging (BMA) framework. A max-min programming is introduced to choose the robust design that maximizes the minimal Box-Hill EED subject to that the highest expected posterior model probability satisfies a desired probability threshold. The EED is calculated by the Gauss-Hermite quadrature. The BMA method is used to predict future observations and to quantify future observation uncertainty arising from conceptual and parametric uncertainties in calculating EED. Monte Carlo approach is adopted to quantify the uncertainty in the posterior model probabilities. The optimal experimental design is tested by a synthetic 5-layer anisotropic confined aquifer. Nine conceptual groundwater models are constructed due to uncertain geological architecture and boundary condition. High-performance computing is used to enumerate all possible design solutions in order to identify the most plausible groundwater model. Results highlight the impacts of scedasticity in future observation data as well as uncertainty sources on potential pumping and observation locations.

Gas-liquid Two Phase Flow Modelling of Incompressible Fluid and Experimental Validation Studies in Vertical Centrifugal Casting

International Nuclear Information System (INIS)

Zhou, J X; Shen, X; Yin, Y J; Guo, Z; Wang, H

2015-01-01

In this paper, Gas-liquid two phase flow mathematic models of incompressible fluid were proposed to explore the feature of fluid under certain centrifugal force in vertical centrifugal casting (VCC). Modified projection-level-set method was introduced to solve the mathematic models. To validate the simulation results, two methods were used in this study. In the first method, the simulation result of basic VCC flow process was compared with its analytic solution. The relationship between the numerical solution and deterministic analytic solution was presented to verify the correctness of numerical algorithms. In the second method, systematic water simulation experiments were developed. In this initial experiment, special experimental vertical centrifugal device and casting shapes were designed to describe typical mold-filling processes in VCC. High speed camera system and data collection devices were used to capture flow shape during the mold-filling process. Moreover, fluid characteristic at different rotation speed (from 40rpm, 60rpmand 80rpm) was discussed to provide comparative resource for simulation results. As compared with the simulation results, the proposed mathematical models could be proven and the experimental design could help us advance the accuracy of simulation and further studies for VCC. (paper)

Experimental and Numerical Analysis of S-CO2 Critical Flow for SFR Recovery System Design

International Nuclear Information System (INIS)

Kim, Min Seok; Jung, Hwa-Young; Ahn, Yoonhan; Lee, Jekyoung; Lee, Jeong Ik

2016-01-01

This paper presents both numerical and experimental studies of the critical flow of S-CO 2 while special attention is given to the turbo-machinery seal design. A computational critical flow model is described first. The experiments were conducted to validate the critical flow model. Various conditions have been tested to study the flow characteristic and provide validation data for the model. The comparison of numerical and experimental results of S-CO 2 critical flow will be presented. In order to eliminate SWR, a concept of coupling the Supercritical CO 2 (S-CO 2 ) cycle with SFR has been proposed. It is known that for a closed system controlling the inventory is important for stable operation and achieving high efficiency. Since the S-CO 2 power cycle is a highly pressurized system, certain amount of leakage flow is inevitable in the rotating turbo-machinery via seals. To simulate the CO 2 leak flow in a turbo-machinery with higher accuracy in the future, the real gas effect and friction factor will be considered for the CO 2 critical flow model. Moreover, experimentally obtained temperature data were somewhat different from the numerically obtained temperature due to the insufficient insulation and large thermal inertia of the CO 2 critical flow facility. Insulation in connecting pipes and the low-pressure tank will be added and additional tests will be conducted

Revised design for the Tokamak experimental power reactor

International Nuclear Information System (INIS)

Stacey, W.M. Jr.; Abdou, M.A.; Brooks, J.N.

1977-03-01

A new, preliminary design has been identified for the tokamak experimental power reactor (EPR). The revised EPR design is simpler, more compact, less expensive and has somewhat better performance characteristics than the previous design, yet retains many of the previously developed design concepts. This report summarizes the principle features of the new EPR design, including performance and cost

Experimental and analytical studies for the validation of HTR-VGD and primary cell passive decay heat removal. Supplement. Calculations

International Nuclear Information System (INIS)

Geiss, M.; Giannikos, A.; Hejzlar, P.; Kneer, A.

1993-04-01

The alternative concept for a modular HTR-reactor design by Siempelkamp, Krefeld, using a prestressed cast iron vessel (VGD) combined with a cast iron/concrete module for the primary cell with integrated passive decay heat removal system was fully qualified with respect to operational and accidental thermal loads. The main emphasis was to confirm and validate the passive decay heat removal capability. An experimental facility (INWA) was designed, instrumented and operated with an appropriate electrical heating system simulating steady-state operational and transient accidental thermal loads. The experiments were accompanied by extensive computations concerning the combination of conductive, radiative and convective energy transport mechanisms in the different components of the VGD/primary cell structures, as well as elastic-plastic stress analyses of the VGD. In addition, a spectrum of potential alternatives for passive energy removed options have been parametrically examined. The experimental data clearly demonstrate that the proposed Siempelkamp-design is able to passively and safely remove the decay heat for operational and accidental conditions without invalidating technological important thermal limits. This also holds in case of failures of both the natural convection system and ultimate heat sink by outside concrete water film cooling. (orig./HP) [de

Experimental design matters for statistical analysis

DEFF Research Database (Denmark)

Jensen, Signe Marie; Schaarschmidt, Frank; Onofri, Andrea

2018-01-01

, the experimental design is often more or less neglected when analyzing data. Two data examples were analyzed using different modelling strategies: Firstly, in a randomized complete block design, mean heights of maize treated with a herbicide and one of several adjuvants were compared. Secondly, translocation...... of an insecticide applied to maize as a seed treatment was evaluated using incomplete data from an unbalanced design with several layers of hierarchical sampling. Extensive simulations were carried out to further substantiate the effects of different modelling strategies. RESULTS: It was shown that results from sub...

Relationship of otolith strontium-to-calcium ratios and salinity: Experimental validation for juvenile salmonids

Science.gov (United States)

Zimmerman, C.E.

2005-01-01

Analysis of otolith strontium (Sr) or strontium-to-calcium (Sr:Ca) ratios provides a powerful tool to reconstruct the chronology of migration among salinity environments for diadromous salmonids. Although use of this method has been validated by examination of known individuals and translocation experiments, it has never been validated under controlled experimental conditions. In this study, incorporation of otolith Sr was tested across a range of salinities and resulting levels of ambient Sr and Ca concentrations in juvenile chinook salmon (Oncorhynchus tshawytscha), coho salmon (Oncorhynchus kisutch), sockeye salmon (Oncorhynchus nerka), rainbow trout (Oncorhynchus rnykiss), and Arctic char (Salvelinus alpinus). Experimental water was mixed, using stream water and seawater as end members, to create experimental salinities of 0.1, 6.3, 12.7, 18.6, 25.5, and 33.0 psu. Otolith Sr and Sr:Ca ratios were significantly related to salinity for all species (r2 range: 0.80-0.91) but provide only enough predictive resolution to discriminate among fresh water, brackish water, and saltwater residency. These results validate the use of otolith Sr:Ca ratios to broadly discriminate salinity histories encountered by salmonids but highlight the need for further research concerning the influence of osmoregulation and physiological changes associated with smoking on otolith microchemistry.

Experimental Testing Procedures and Dynamic Model Validation for Vanadium Redox Flow Battery Storage System

DEFF Research Database (Denmark)

Baccino, Francesco; Marinelli, Mattia; Nørgård, Per Bromand

2013-01-01

The paper aims at characterizing the electrochemical and thermal parameters of a 15 kW/320 kWh vanadium redox flow battery (VRB) installed in the SYSLAB test facility of the DTU Risø Campus and experimentally validating the proposed dynamic model realized in Matlab-Simulink. The adopted testing...... efficiency of the battery system. The test procedure has general validity and could also be used for other storage technologies. The storage model proposed and described is suitable for electrical studies and can represent a general model in terms of validity. Finally, the model simulation outputs...

Impact-friction vibrations of tubular systems. Numerical simulation and experimental validation

International Nuclear Information System (INIS)

Jacquart, G.

1993-05-01

This note presents a summary on the numerical developments made to simulate impact-friction vibrations of tubular systems, detailing the algorithms used and the expression of impact and friction forces. A synthesis of the experimental results obtained on MASSIF workbench is also presented, as well as their comparison with numerical computations in order to validate the numerical approach. (author). 5 refs

Verification and validation benchmarks

International Nuclear Information System (INIS)

Oberkampf, William Louis; Trucano, Timothy Guy

2007-01-01

Verification and validation (V and V) are the primary means to assess the accuracy and reliability of computational simulations. V and V methods and procedures have fundamentally improved the credibility of simulations in several high-consequence fields, such as nuclear reactor safety, underground nuclear waste storage, and nuclear weapon safety. Although the terminology is not uniform across engineering disciplines, code verification deals with assessing the reliability of the software coding, and solution verification deals with assessing the numerical accuracy of the solution to a computational model. Validation addresses the physics modeling accuracy of a computational simulation by comparing the computational results with experimental data. Code verification benchmarks and validation benchmarks have been constructed for a number of years in every field of computational simulation. However, no comprehensive guidelines have been proposed for the construction and use of V and V benchmarks. For example, the field of nuclear reactor safety has not focused on code verification benchmarks, but it has placed great emphasis on developing validation benchmarks. Many of these validation benchmarks are closely related to the operations of actual reactors at near-safety-critical conditions, as opposed to being more fundamental-physics benchmarks. This paper presents recommendations for the effective design and use of code verification benchmarks based on manufactured solutions, classical analytical solutions, and highly accurate numerical solutions. In addition, this paper presents recommendations for the design and use of validation benchmarks, highlighting the careful design of building-block experiments, the estimation of experimental measurement uncertainty for both inputs and outputs to the code, validation metrics, and the role of model calibration in validation. It is argued that the understanding of predictive capability of a computational model is built on the

Verification and validation benchmarks

International Nuclear Information System (INIS)

Oberkampf, William L.; Trucano, Timothy G.

2008-01-01

Verification and validation (V and V) are the primary means to assess the accuracy and reliability of computational simulations. V and V methods and procedures have fundamentally improved the credibility of simulations in several high-consequence fields, such as nuclear reactor safety, underground nuclear waste storage, and nuclear weapon safety. Although the terminology is not uniform across engineering disciplines, code verification deals with assessing the reliability of the software coding, and solution verification deals with assessing the numerical accuracy of the solution to a computational model. Validation addresses the physics modeling accuracy of a computational simulation by comparing the computational results with experimental data. Code verification benchmarks and validation benchmarks have been constructed for a number of years in every field of computational simulation. However, no comprehensive guidelines have been proposed for the construction and use of V and V benchmarks. For example, the field of nuclear reactor safety has not focused on code verification benchmarks, but it has placed great emphasis on developing validation benchmarks. Many of these validation benchmarks are closely related to the operations of actual reactors at near-safety-critical conditions, as opposed to being more fundamental-physics benchmarks. This paper presents recommendations for the effective design and use of code verification benchmarks based on manufactured solutions, classical analytical solutions, and highly accurate numerical solutions. In addition, this paper presents recommendations for the design and use of validation benchmarks, highlighting the careful design of building-block experiments, the estimation of experimental measurement uncertainty for both inputs and outputs to the code, validation metrics, and the role of model calibration in validation. It is argued that the understanding of predictive capability of a computational model is built on the

Seaworthy Quantum Key Distribution Design and Validation (SEAKEY)

Science.gov (United States)

2015-11-12

polarization control and the CV state and the LO state are separated at a polarizing beam splitter . The CV state is delayed relative to the LO state, and... splitter or loss imperfections. We have identified a number of risks associated with implementing this design . The two most critical risks are: • The...Contractor Address: 10 Moulton Street, Cambridge, MA 02138 Title of the Project: Seaworthy Quantum Key Distribution Design and Validation (SEAKEY

Using a Non-Equivalent Groups Quasi Experimental Design to Reduce Internal Validity Threats to Claims Made by Math and Science K-12 Teacher Recruitment Programs

Science.gov (United States)

Moin, Laura

2009-10-01

The American Recovery and Reinvestment Act national policy established in 2009 calls for ``meaningful data'' that demonstrate educational improvements, including the recruitment of high-quality teachers. The scant data available and the low credibility of many K-12 math/science teacher recruitment program evaluations remain the major barriers for the identification of effective recruitment strategies. Our study presents a methodology to better evaluate the impact of recruitment programs on increasing participants' interest in teaching careers. The research capitalizes on the use of several control groups and presents a non-equivalent groups quasi-experimental evaluation design that produces program effect claims with higher internal validity than claims generated by current program evaluations. With this method that compares responses to a teaching career interest question from undergraduates all along a continuum from just attending an information session to participating (or not) in the recruitment program, we were able to compare the effect of the program in increasing participants' interest in teaching careers versus the evolution of the same interest but in the absence of the program. We were also able to make suggestions for program improvement and further research. While our findings may not apply to other K-12 math/science teacher recruitment programs, we believe that our evaluation methodology does and will contribute to conduct stronger program evaluations. In so doing, our evaluation procedure may inform recruitment program designers and policy makers.

Experimental validation of the buildings energy performance (PEC assessment methods with reference to occupied spaces heating

Directory of Open Access Journals (Sweden)

Cristian PETCU

2010-01-01

Full Text Available This paper is part of the series of pre-standardization research aimed to analyze the existing methods of calculating the Buildings Energy Performance (PEC in view of their correction of completing. The entire research activity aims to experimentally validate the PEC Calculation Algorithm as well as the comparative application, on the support of several case studies focused on representative buildings of the stock of buildings in Romania, of the PEC calculation methodology for buildings equipped with occupied spaces heating systems. The targets of the report are the experimental testing of the calculation models so far known (NP 048-2000, Mc 001-2006, SR EN 13790:2009, on the support provided by the CE INCERC Bucharest experimental building, together with the complex calculation algorithms specific to the dynamic modeling, for the evaluation of the occupied spaces heat demand in the cold season, specific to the traditional buildings and to modern buildings equipped with solar radiation passive systems, of the ventilated solar space type. The schedule of the measurements performed in the 2008-2009 cold season is presented as well as the primary processing of the measured data and the experimental validation of the heat demand monthly calculation methods, on the support of CE INCERC Bucharest. The calculation error per heating season (153 days of measurements between the measured heat demand and the calculated one was of 0.61%, an exceptional value confirming the phenomenological nature of the INCERC method, NP 048-2006. The mathematical model specific to the hourly thermal balance is recurrent – decisional with alternating paces. The experimental validation of the theoretical model is based on the measurements performed on the CE INCERC Bucharest building, within a time lag of 57 days (06.01-04.03.2009. The measurements performed on the CE INCERC Bucharest building confirm the accuracy of the hourly calculation model by comparison to the values

Neural Network Assisted Experimental Designs for Food Research

Directory of Open Access Journals (Sweden)

H.S. Ramaswamy

2000-06-01

Full Text Available The ability of artificial neural networks (ANN in predicting full factorial data from the fractional data corresponding to some of the commonly used experimental designs is explored in this paper. Factorial and fractional factorial designs such as L8, L9, L18, and Box and Behnken schemes were considered both in their original form and with some variations (L8+6, L15 and L9+1. Full factorial (3 factors x 5 levels and fractional data were generated employing sixteen different mathematical equations (four in each category: linear, with and without interactions, and non-linear, with and without interactions. Different ANN models were trained and the best model was chosen for each equation based on their ability to predict the fractional data. The best experimental design was then chosen based on their ability to simulate the full- factorial data for each equation. In several cases, the mean relative errors with the L18 design (which had more input data than other models were even higher than with other smaller fractional design. In general, the ANN assisted Lm, Box and Behnken, L15 and L18 designs were found to predict the full factorial data reasonably well with errors less than 5 %. The L8+6 model performed well with several experimental datasets reported in the literature.

Experimental designs for autoregressive models applied to industrial maintenance

International Nuclear Information System (INIS)

Amo-Salas, M.; López-Fidalgo, J.; Pedregal, D.J.

2015-01-01

Some time series applications require data which are either expensive or technically difficult to obtain. In such cases scheduling the points in time at which the information should be collected is of paramount importance in order to optimize the resources available. In this paper time series models are studied from a new perspective, consisting in the use of Optimal Experimental Design setup to obtain the best times to take measurements, with the principal aim of saving costs or discarding useless information. The model and the covariance function are expressed in an explicit form to apply the usual techniques of Optimal Experimental Design. Optimal designs for various approaches are computed and their efficiencies are compared. The methods working in an application of industrial maintenance of a critical piece of equipment at a petrochemical plant are shown. This simple model allows explicit calculations in order to show openly the procedure to find the correlation structure, needed for computing the optimal experimental design. In this sense the techniques used in this paper to compute optimal designs may be transferred to other situations following the ideas of the paper, but taking into account the increasing difficulty of the procedure for more complex models. - Highlights: • Optimal experimental design theory is applied to AR models to reduce costs. • The first observation has an important impact on any optimal design. • Either the lack of precision or small starting observations claim for large times. • Reasonable optimal times were obtained relaxing slightly the efficiency. • Optimal designs were computed in a predictive maintenance context

Experimental validation of the TOPAS Monte Carlo system for passive scattering proton therapy

International Nuclear Information System (INIS)

Testa, M.; Schümann, J.; Lu, H.-M.; Paganetti, H.; Shin, J.; Faddegon, B.; Perl, J.

2013-01-01

Purpose: TOPAS (TOol for PArticle Simulation) is a particle simulation code recently developed with the specific aim of making Monte Carlo simulations user-friendly for research and clinical physicists in the particle therapy community. The authors present a thorough and extensive experimental validation of Monte Carlo simulations performed with TOPAS in a variety of setups relevant for proton therapy applications. The set of validation measurements performed in this work represents an overall end-to-end testing strategy recommended for all clinical centers planning to rely on TOPAS for quality assurance or patient dose calculation and, more generally, for all the institutions using passive-scattering proton therapy systems. Methods: The authors systematically compared TOPAS simulations with measurements that are performed routinely within the quality assurance (QA) program in our institution as well as experiments specifically designed for this validation study. First, the authors compared TOPAS simulations with measurements of depth-dose curves for spread-out Bragg peak (SOBP) fields. Second, absolute dosimetry simulations were benchmarked against measured machine output factors (OFs). Third, the authors simulated and measured 2D dose profiles and analyzed the differences in terms of field flatness and symmetry and usable field size. Fourth, the authors designed a simple experiment using a half-beam shifter to assess the effects of multiple Coulomb scattering, beam divergence, and inverse square attenuation on lateral and longitudinal dose profiles measured and simulated in a water phantom. Fifth, TOPAS’ capabilities to simulate time dependent beam delivery was benchmarked against dose rate functions (i.e., dose per unit time vs time) measured at different depths inside an SOBP field. Sixth, simulations of the charge deposited by protons fully stopping in two different types of multilayer Faraday cups (MLFCs) were compared with measurements to benchmark the

Optimization and design of an aircraft's morphing wing-tip demonstrator for drag reduction at low speeds, Part II - Experimental validation using Infra-Red transition measurement from Wind Tunnel tests

Directory of Open Access Journals (Sweden)

Andreea Koreanschi

2017-02-01

Full Text Available In the present paper, an ‘in-house’ genetic algorithm was numerically and experimentally validated. The genetic algorithm was applied to an optimization problem for improving the aerodynamic performances of an aircraft wing tip through upper surface morphing. The optimization was performed for 16 flight cases expressed in terms of various combinations of speeds, angles of attack and aileron deflections. The displacements resulted from the optimization were used during the wind tunnel tests of the wing tip demonstrator for the actuators control to change the upper surface shape of the wing. The results of the optimization of the flow behavior for the airfoil morphing upper-surface problem were validated with wind tunnel experimental transition results obtained with infra-red Thermography on the wing-tip demonstrator. The validation proved that the 2D numerical optimization using the ‘in-house’ genetic algorithm was an appropriate tool in improving various aspects of a wing’s aerodynamic performances.

Design and validation of advanced driver assistance systems

NARCIS (Netherlands)

Gietelink, O.J.

2007-01-01

This thesis presents new tools and methods for the design and validation of advanced driver assistance systems (ADASs). ADASs aim to improve driving comfort and traffic safety by assisting the driver in recognizing and reacting to potentially dangerous traffic situations. A major challenge in

Experimental design techniques in statistical practice a practical software-based approach

CERN Document Server

Gardiner, W P

1998-01-01

Provides an introduction to the diverse subject area of experimental design, with many practical and applicable exercises to help the reader understand, present and analyse the data. The pragmatic approach offers technical training for use of designs and teaches statistical and non-statistical skills in design and analysis of project studies throughout science and industry. Provides an introduction to the diverse subject area of experimental design and includes practical and applicable exercises to help understand, present and analyse the data Offers technical training for use of designs and teaches statistical and non-statistical skills in design and analysis of project studies throughout science and industry Discusses one-factor designs and blocking designs, factorial experimental designs, Taguchi methods and response surface methods, among other topics.

Quantification of construction waste prevented by BIM-based design validation: Case studies in South Korea.

Science.gov (United States)

Won, Jongsung; Cheng, Jack C P; Lee, Ghang

2016-03-01

Waste generated in construction and demolition processes comprised around 50% of the solid waste in South Korea in 2013. Many cases show that design validation based on building information modeling (BIM) is an effective means to reduce the amount of construction waste since construction waste is mainly generated due to improper design and unexpected changes in the design and construction phases. However, the amount of construction waste that could be avoided by adopting BIM-based design validation has been unknown. This paper aims to estimate the amount of construction waste prevented by a BIM-based design validation process based on the amount of construction waste that might be generated due to design errors. Two project cases in South Korea were studied in this paper, with 381 and 136 design errors detected, respectively during the BIM-based design validation. Each design error was categorized according to its cause and the likelihood of detection before construction. The case studies show that BIM-based design validation could prevent 4.3-15.2% of construction waste that might have been generated without using BIM. Copyright © 2015 Elsevier Ltd. All rights reserved.

Modeling and Experimental Validation for 3D mm-wave Radar Imaging

Science.gov (United States)

Ghazi, Galia

As the problem of identifying suicide bombers wearing explosives concealed under clothing becomes increasingly important, it becomes essential to detect suspicious individuals at a distance. Systems which employ multiple sensors to determine the presence of explosives on people are being developed. Their functions include observing and following individuals with intelligent video, identifying explosives residues or heat signatures on the outer surface of their clothing, and characterizing explosives using penetrating X-rays, terahertz waves, neutron analysis, or nuclear quadrupole resonance. At present, mm-wave radar is the only modality that can both penetrate and sense beneath clothing at a distance of 2 to 50 meters without causing physical harm. Unfortunately, current mm-wave radar systems capable of performing high-resolution, real-time imaging require using arrays with a large number of transmitting and receiving modules; therefore, these systems present undesired large size, weight and power consumption, as well as extremely complex hardware architecture. The overarching goal of this thesis is the development and experimental validation of a next generation inexpensive, high-resolution radar system that can distinguish security threats hidden on individuals located at 2-10 meters range. In pursuit of this goal, this thesis proposes the following contributions: (1) Development and experimental validation of a new current-based, high-frequency computational method to model large scattering problems (hundreds of wavelengths) involving lossy, penetrable and multi-layered dielectric and conductive structures, which is needed for an accurate characterization of the wave-matter interaction and EM scattering in the target region; (2) Development of combined Norm-1, Norm-2 regularized imaging algorithms, which are needed for enhancing the resolution of the images while using a minimum number of transmitting and receiving antennas; (3) Implementation and experimental

On validation of the rain climatic zone designations for Nigeria

Science.gov (United States)

Obiyemi, O. O.; Ibiyemi, T. S.; Ojo, J. S.

2017-07-01

In this paper, validation of rain climatic zone classifications for Nigeria is presented based on global radio-climatic models by the International Telecommunication Union-Radiocommunication (ITU-R) and Crane. Rain rate estimates deduced from several ground-based measurements and those earlier estimated from the precipitation index on the Tropical Rain Measurement Mission (TRMM) were employed for the validation exercise. Although earlier classifications indicated that Nigeria falls into zones P, Q, N, and K for the ITU-R designations, and zones E and H for Crane's climatic zone designations, the results however confirmed that the rain climatic zones across Nigeria can only be classified into four, namely P, Q, M, and N for the ITU-R designations, while the designations by Crane exhibited only three zones, namely E, G, and H. The ITU-R classification was found to be more suitable for planning microwave and millimeter wave links across Nigeria. The research outcomes are vital in boosting the confidence level of system designers in using the ITU-R designations as presented in the map developed for the rain zone designations for estimating the attenuation induced by rain along satellite and terrestrial microwave links over Nigeria.

Achieving external validity in home advantage research: generalizing crowd noise effects

Directory of Open Access Journals (Sweden)

Tony D Myers

2014-06-01

Full Text Available Different factors have been postulated to explain the home advantage phenomenon in sport. One plausible explanation investigated has been the influence of a partisan home crowd on sports officials’ decisions. Different types of studies have tested the crowd influence hypothesis including purposefully designed experiments. However, while experimental studies investigating crowd influences have high levels of internal validity, they suffer from a lack of external validity; decision-making in a laboratory setting bearing little resemblance to decision-making in live sports settings. This focused review initially considers threats to external validity in applied and theoretical experimental research. Discussing how such threats can be addressed using representative design by focusing on a recently published study that arguably provides the first experimental evidence of the impact of live crowd noise on officials in sport. The findings of this controlled experiment conducted in a real tournament setting offer some confirmation of the validity of laboratory experimental studies in the area. Finally directions for future research and the future conduct of crowd noise studies are discussed.

MATLAB/Simulink Pulse-Echo Ultrasound System Simulator Based on Experimentally Validated Models.

Science.gov (United States)

Kim, Taehoon; Shin, Sangmin; Lee, Hyongmin; Lee, Hyunsook; Kim, Heewon; Shin, Eunhee; Kim, Suhwan

2016-02-01

A flexible clinical ultrasound system must operate with different transducers, which have characteristic impulse responses and widely varying impedances. The impulse response determines the shape of the high-voltage pulse that is transmitted and the specifications of the front-end electronics that receive the echo; the impedance determines the specification of the matching network through which the transducer is connected. System-level optimization of these subsystems requires accurate modeling of pulse-echo (two-way) response, which in turn demands a unified simulation of the ultrasonics and electronics. In this paper, this is realized by combining MATLAB/Simulink models of the high-voltage transmitter, the transmission interface, the acoustic subsystem which includes wave propagation and reflection, the receiving interface, and the front-end receiver. To demonstrate the effectiveness of our simulator, the models are experimentally validated by comparing the simulation results with the measured data from a commercial ultrasound system. This simulator could be used to quickly provide system-level feedback for an optimized tuning of electronic design parameters.

Development of a quality-assessment tool for experimental bruxism studies: reliability and validity

NARCIS (Netherlands)

Dawson, A.; Raphael, K.G.; Glaros, A.; Axelsson, S.; Arima, T.; Ernberg, M.; Farella, M.; Lobbezoo, F.; Manfredini, D.; Michelotti, A.; Svensson, P.; List, T.

2013-01-01

AIMS: To combine empirical evidence and expert opinion in a formal consensus method in order to develop a quality-assessment tool for experimental bruxism studies in systematic reviews. METHODS: Tool development comprised five steps: (1) preliminary decisions, (2) item generation, (3) face-validity

Experiential design landscapes: design research in the wild

NARCIS (Netherlands)

Peeters, M.M.R.; Megens, C.J.P.G.; IJsselsteijn, W.A.; Hummels, C.C.M.; Brombacher, A.C.; Brandt, E.; Ehn, P.; Johansson, T.; Johansson, T.D.; Hellström Reimer, M.; Markussen, T.; Vallgårda, A.

2013-01-01

Thanks to the emergence of new sensing and behaviour tracking technologies, design research can take place anywhere and anytime in the real world. When doing design research, a trade-off has to be made between experimental control and ecological validity. In this paper, we compare Experiential

DTU-ESA millimeter-wave validation standard antenna – requirements and design

DEFF Research Database (Denmark)

Pivnenko, Sergey; Kim, Oleksiy S.; Breinbjerg, Olav

2014-01-01

from a validation campaign is achieved when a dedicated Validation Standard (VAST) antenna specifically designed for this purpose is available. The driving requirements to VAST antennas are their mechanical stability with respect to any orientation of the antenna in the gravity field and thermal...... are briefly reviewed and the baseline design is described. The emphasis is given to definition of the requirements for the mechanical and thermal stability of the antenna, which satisfy the stringent stability requirement for the mm-VAST electrical characteristics....

Research Methods in Healthcare Epidemiology and Antimicrobial Stewardship – Quasi-Experimental Designs

Science.gov (United States)

Schweizer, Marin L.; Braun, Barbara I.; Milstone, Aaron M.

2016-01-01

Quasi-experimental studies evaluate the association between an intervention and an outcome using experiments in which the intervention is not randomly assigned. Quasi-experimental studies are often used to evaluate rapid responses to outbreaks or other patient safety problems requiring prompt non-randomized interventions. Quasi-experimental studies can be categorized into three major types: interrupted time series designs, designs with control groups, and designs without control groups. This methods paper highlights key considerations for quasi-experimental studies in healthcare epidemiology and antimicrobial stewardship including study design and analytic approaches to avoid selection bias and other common pitfalls of quasi-experimental studies. PMID:27267457

Design activities of a fusion experimental breeder

International Nuclear Information System (INIS)

Huang, J.; Feng, K.; Sheng, G.

1999-01-01

The fusion reactor design studies in China are under the support of a fusion-fission hybrid reactor research Program. The purpose of this program is to explore the potential near-term application of fusion energy to support the long-term fusion energy on the one hand and the fission energy development on the other. During 1992-1996 a detailed consistent and integral conceptual design of a Fusion Experimental Breeder, FEB was completed. Beginning from 1996, a further design study towards an Engineering Outline Design of the FEB, FEB-E, has started. The design activities are briefly given. (author)

Design activities of a fusion experimental breeder

International Nuclear Information System (INIS)

Huang, J.; Feng, K.; Sheng, G.

2001-01-01

The fusion reactor design studies in China are under the support of a fusion-fission hybrid reactor research Program. The purpose of this program is to explore the potential near-term application of fusion energy to support the long-term fusion energy on the one hand and the fission energy development on the other. During 1992-1996 a detailed consistent and integral conceptual design of a Fusion Experimental Breeder, FEB was completed. Beginning from 1996, a further design study towards an Engineering Outline Design of the FEB, FEB-E, has started. The design activities are briefly given. (author)

An Introduction to Experimental Design Research

DEFF Research Database (Denmark)

Cash, Philip; Stanković, Tino; Štorga, Mario

2016-01-01

Design research brings together influences from the whole gamut of social, psychological, and more technical sciences to create a tradition of empirical study stretching back over 50 years (Horvath 2004; Cross 2007). A growing part of this empirical tradition is experimental, which has gained in ...

Design and Validation of Affective Warning Pictorial on Cigarette Labels

Directory of Open Access Journals (Sweden)

Chanduen Pat-Arin

2016-01-01

Full Text Available The purpose of present study were to design and validate affective warning pictorials for cigarette label in Thailand. Brainstorming and survey techniques were used to collect the idea of possible warning pictorials. All ideas were grouped for finding candidated pictorials. Then, primary sixty warning pictorials were collected and equally classified into three affective warning pictorial groups as positive, neutral, and negative. Sixty Thai male engineering students participated in affective validation of warning pictorials using SAM rating. The International Affective Picture System (IAPS was used to manipulate the affective state of participants to neutral affective state before the experiments. The results revealed that all affective warning pictorials were successfully evoked target affective states on participants. After refining, thirty affective warning pictorials were provided as positive, neutral, and negative affective warning pictorials for using on cigarette labels. Implications on the affective warning pictorials design and validation.

Measuring Children’s Perceptions of Robots’ Social Competence : Design and Validation

NARCIS (Netherlands)

Davison, Daniel Patrick; Charisi, Vasiliki; Wijnen, Frances Martine; Reidsma, Dennis; Evers, Vanessa; Kheddar, Abderrahmane; Yoshida, Eiichi; Ge, Shuzhi Sam; Suzuki, Kenji; Cabibihan, John-John; Eyssel, Friederike; He, Hongsheng

2017-01-01

This paper presents the design and validation of a measurement instrument for children’s perceptions of robots’ social competence. The need for a standardized validated instrument has emerged as a requisite for meta-analyses and comparisons among various studies in the field of child-robot

In Silico Design and Experimental Validation of siRNAs Targeting Conserved Regions of Multiple Hepatitis C Virus Genotypes.

Directory of Open Access Journals (Sweden)

Mahmoud ElHefnawi

Full Text Available RNA interference (RNAi is a post-transcriptional gene silencing mechanism that mediates the sequence-specific degradation of targeted RNA and thus provides a tremendous opportunity for development of oligonucleotide-based drugs. Here, we report on the design and validation of small interfering RNAs (siRNAs targeting highly conserved regions of the hepatitis C virus (HCV genome. To aim for therapeutic applications by optimizing the RNAi efficacy and reducing potential side effects, we considered different factors such as target RNA variations, thermodynamics and accessibility of the siRNA and target RNA, and off-target effects. This aim was achieved using an in silico design and selection protocol complemented by an automated MysiRNA-Designer pipeline. The protocol included the design and filtration of siRNAs targeting highly conserved and accessible regions within the HCV internal ribosome entry site, and adjacent core sequences of the viral genome with high-ranking efficacy scores. Off-target analysis excluded siRNAs with potential binding to human mRNAs. Under this strict selection process, two siRNAs (HCV353 and HCV258 were selected based on their predicted high specificity and potency. These siRNAs were tested for antiviral efficacy in HCV genotype 1 and 2 replicon cell lines. Both in silico-designed siRNAs efficiently inhibited HCV RNA replication, even at low concentrations and for short exposure times (24h; they also exceeded the antiviral potencies of reference siRNAs targeting HCV. Furthermore, HCV353 and HCV258 siRNAs also inhibited replication of patient-derived HCV genotype 4 isolates in infected Huh-7 cells. Prolonged treatment of HCV replicon cells with HCV353 did not result in the appearance of escape mutant viruses. Taken together, these results reveal the accuracy and strength of our integrated siRNA design and selection protocols. These protocols could be used to design highly potent and specific RNAi-based therapeutic

Mini-channel flow experiments and CFD validation analyses with the IFMIF Thermo- Hydraulic Experimental facility (ITHEX)

International Nuclear Information System (INIS)

Arbeiter, F.; Heinzel, V.; Leichtle, D.; Stratmanns, E.; Gordeev, S.

2006-01-01

The design of the IFMIF High Flux Test Module (HFTM) is based on the predictions for the heat transfer in narrow channels conducting helium flow of 50 o C inlet temperature at 0.3 MPa. The emerging helium flow conditions are in the transition regime of laminar to turbulent flow. The rectangular cooling channels are too short for the full development of the coolant flow. Relaminarization along the cooling passage is expected. At the shorter sides of the channels secondary flow occurs, which may have an impact on the temperature field inside the irradiation specimen's stack. As those conditions are not covered by available experimental data, the dedicated gas loop ITHEX has been constructed to operate up to a pressure of 0.42 MPa and temperatures of 200 o C. It's objective is to conduct experiments for the validation of the STAR-CD CFD code used for the design of the HFTM. As a first stage, two annular test-sections with hydraulic diameter of 1.2 mm have been used, where the experiments have been varied with respect to gas species (N 2 , He), inlet pressure, dimensionless heating span and Reynolds number encompassing the range of operational parameters of the HFTM. Local friction factors and Nusselt numbers have been obtained giving evidence that the transition regime will extend to Reynolds 10,000. For heating rates comparable to the HFTM filled with RAFM steels, local heat transfer coefficients are in consistence with the measured friction data. To validate local velocity profiles the ITHEX facility was further equipped with a flat rectangular test-section and a Laser Doppler Anemometry (LDA) system. An appropriate optical system has been developed and tested for the tiny observation volume of 40 μm diameter. Velocity profiles as induced by the transition of a wide inlet plenum to the flat mini-channels have been measured. Whereas the CFD models were able to reproduce the patterns far away from the nozzle, they show some disagreement for the conditions at the

Recent Advances in Simulation of Eddy Current Testing of Tubes and Experimental Validations

Science.gov (United States)

Reboud, C.; Prémel, D.; Lesselier, D.; Bisiaux, B.

2007-03-01

Eddy current testing (ECT) is widely used in iron and steel industry for the inspection of tubes during manufacturing. A collaboration between CEA and the Vallourec Research Center led to the development of new numerical functionalities dedicated to the simulation of ECT of non-magnetic tubes by external probes. The achievement of experimental validations led us to the integration of these models into the CIVA platform. Modeling approach and validation results are discussed here. A new numerical scheme is also proposed in order to improve the accuracy of the model.

Survey of experimental tests about progressive distortion

International Nuclear Information System (INIS)

Clement, Gerard.

1981-02-01

A procedure for evaluation of progressive distorsion experimental data has been set up in CEA. This procedure based on the effective primary stress concept, permits the establishment of a simple design rule. Various published experimental data have been used for verification, validation and generalization of design rule proposed. This rule is compared with existing codified rules (3 Sm, BREE, O'DONNEL and POROWSKI) [fr

Statistical experimental design for saltstone mixtures

International Nuclear Information System (INIS)

Harris, S.P.; Postles, R.L.

1991-01-01

We used a mixture experimental design for determining a window of operability for a process at the Savannah River Site Defense Waste Processing Facility (DWPF). The high-level radioactive waste at the Savannah River Site is stored in large underground carbon steel tanks. The waste consists of a supernate layer and a sludge layer. 137 Cs will be removed from the supernate by precipitation and filtration. After further processing, the supernate layer will be fixed as a grout for disposal in concrete vaults. The remaining precipitate will be processed at the DWPF with treated waste tank sludge and glass-making chemicals into borosilicate glass. The leach rate properties of the supernate grout, formed from various mixes of solidified salt waste, needed to be determined. The effective diffusion coefficients for NO 3 and Cr were used as a measure of leach rate. Various mixes of cement, Ca(OH) 2 , salt, slag and flyash were used. These constituents comprise the whole mix. Thus, a mixture experimental design was used

Experimental site and design

Energy Technology Data Exchange (ETDEWEB)

Guenette, C. C. [SINTEF Applied Cemistry, Trondheim (Norway)

1999-08-01

Design and site selection criteria for the Svalbard oil spill experiments are described. All three experimental sites have coarse and mixed sediment beaches of sand and pebble; within each site wave exposure is very similar; along-shore and across-shore sediment characteristics are also relatively homogeneous. Tidal range is in the order of 0.6 m at neaps, and 1.8 m at springs. All three sites are open to wave action and are ice-free during the experimental period of mid-July to mid-October. Study plots at each site were selected for different treatments from within the continuous stretch of oiled shoreline, with oiled buffer zones between plots and at either end of the oiled zone. Treatments included mixing (tilling), sediment relocation (surf washing) and bioremediation (nutrient enrichment). Measurements and observations were carried out during the summers of 1997 and 1998. The characteristics measured were: wave and wind conditions; beach topography and elevation; sediment grain size distribution; mineral fines size distribution and mineral composition; background hydrocarbons; concentration of oil within experimental plots and the rate of oil loss over time; depth of oil penetration and thickness of the oiled sediment layer; oil concentration and toxicity of near-shore benthic sediments; mineral composition of suspended particulate material captured in sub-tidal sediment traps; and oil-fines interaction in near-shore water samples. 1 fig.

Experimental site and design

Energy Technology Data Exchange (ETDEWEB)

Guenette, C. C. [SINTEF Applied Cemistry, Trondheim (Norway)

1999-07-01

Design and site selection criteria for the Svalbard oil spill experiments are described. All three experimental sites have coarse and mixed sediment beaches of sand and pebble; within each site waveexposure is very similar; along-shore and across-shore sediment characteristics are also relatively homogeneous. Tidal range is in the order of 0.6 m at neaps, and 1.8 m at springs. All three sites are open to wave action and are ice-free during the experimental period of mid-July to mid-October. Study plots at each site were selected for different treatments from within the continuous stretch of oiled shoreline, with oiled buffer zones between plots and at either end of the oiled zone. Treatments included mixing (tilling), sediment relocation (surf washing) and bioremediation (nutrient enrichment). Measurements and observations were carried out during the summers of 1997 and 1998. The characteristics measured were: wave and wind conditions; beach topography and elevation; sediment grain size distribution; mineral fines size distribution and mineral composition; background hydrocarbons; concentration of oil within experimental plots and the rate of oil loss over time; depth of oil penetration and thickness of the oiled sediment layer; oil concentration and toxicity of near-shore benthic sediments; mineral composition of suspended particulate material captured in sub-tidal sediment traps; and oil-fines interaction in near-shore water samples. 1 fig.

Design and validation of a uniform flow microreactor

Energy Technology Data Exchange (ETDEWEB)

Yi, Seung Jae; Kim, Kyung Chun; Chang, Seung Cheol [Pusan National University, Busan (Korea, Republic of); Park, Ji Min [Global HQ, Hankook Tire Co., Daejeon (Korea, Republic of)

2014-01-15

We present a design method to characterize uniform flows in a microreactor for high performance surface plasmon resonance (SPR) a general-purpose biosensor chips. The shape of the microreactor is designed based on an approximate pressure drop model. The number of micro-pillars and the slopes of the inlet and outlet linear chambers are two dominant parameters used to minimize the velocity difference in the microreactor. The flow uniformity was examined quantitatively by numerical and experimental visualization methods. A computational fluid dynamics (CFD) analysis demonstrates that the designed microreactor has a fairly uniform velocity profile in the reaction zone for a wide range of flow rates. The velocity field in the fabricated microreactor was measured using the micro-particle image velocimetry (μ-PIV) method, and the flow uniformity was confirmed experimentally. The performance of the uniform flow microreactor was verified using the fluorescence antibody technique.

Experimental validation of the twins prediction program for rolling noise. Pt.2: results

NARCIS (Netherlands)

Thompson, D.J.; Fodiman, P.; Mahé, H.

1996-01-01

Two extensive measurement campaigns have been carried out to validate the TWINS prediction program for rolling noise, as described in part 1 of this paper. This second part presents the experimental results of vibration and noise during train pass-bys and compares them with predictions from the

System design overview of JAXA small supersonic experimental airplane (NEXST-1)

OpenAIRE

Takami, Hikaru; 高見　光

2007-01-01

The system of JAXA small supersonic experimental airplane (NEXST-1: National EXperimental Supersonic Transport-1) has been briefly explained. Some design problems that the designers have encountered have also been briefly explained.

Experimental and Sampling Design for the INL-2 Sample Collection Operational Test

Energy Technology Data Exchange (ETDEWEB)

Piepel, Gregory F.; Amidan, Brett G.; Matzke, Brett D.

2009-02-16

This report describes the experimental and sampling design developed to assess sampling approaches and methods for detecting contamination in a building and clearing the building for use after decontamination. An Idaho National Laboratory (INL) building will be contaminated with BG (Bacillus globigii, renamed Bacillus atrophaeus), a simulant for Bacillus anthracis (BA). The contamination, sampling, decontamination, and re-sampling will occur per the experimental and sampling design. This INL-2 Sample Collection Operational Test is being planned by the Validated Sampling Plan Working Group (VSPWG). The primary objectives are: 1) Evaluate judgmental and probabilistic sampling for characterization as well as probabilistic and combined (judgment and probabilistic) sampling approaches for clearance, 2) Conduct these evaluations for gradient contamination (from low or moderate down to absent or undetectable) for different initial concentrations of the contaminant, 3) Explore judgment composite sampling approaches to reduce sample numbers, 4) Collect baseline data to serve as an indication of the actual levels of contamination in the tests. A combined judgmental and random (CJR) approach uses Bayesian methodology to combine judgmental and probabilistic samples to make clearance statements of the form "X% confidence that at least Y% of an area does not contain detectable contamination” (X%/Y% clearance statements). The INL-2 experimental design has five test events, which 1) vary the floor of the INL building on which the contaminant will be released, 2) provide for varying the amount of contaminant released to obtain desired concentration gradients, and 3) investigate overt as well as covert release of contaminants. Desirable contaminant gradients would have moderate to low concentrations of contaminant in rooms near the release point, with concentrations down to zero in other rooms. Such gradients would provide a range of contamination levels to challenge the sampling

Design and Experimental Study of an Over-Under TBCC Exhaust System.

Science.gov (United States)

Mo, Jianwei; Xu, Jinglei; Zhang, Liuhuan

2014-01-01

Turbine-based combined-cycle (TBCC) propulsion systems have been a topic of research as a means for more efficient flight at supersonic and hypersonic speeds. The present study focuses on the fundamental physics of the complex flow in the TBCC exhaust system during the transition mode as the turbine exhaust is shut off and the ramjet exhaust is increased. A TBCC exhaust system was designed using methods of characteristics (MOC) and subjected to experimental and computational study. The main objectives of the study were: (1) to identify the interactions between the two exhaust jet streams during the transition mode phase and their effects on the whole flow-field structure; (2) to determine and verify the aerodynamic performance of the over-under TBCC exhaust nozzle; and (3) to validate the simulation ability of the computational fluid dynamics (CFD) software according to the experimental conditions. Static pressure taps and Schlieren apparatus were employed to obtain the wall pressure distributions and flow-field structures. Steady-state tests were performed with the ramjet nozzle cowl at six different positions at which the turbine flow path were half closed and fully opened, respectively. Methods of CFD were used to simulate the exhaust flow and they complemented the experimental study by providing greater insight into the details of the flow field and a means of verifying the experimental results. Results indicated that the flow structure was complicated because the two exhaust jet streams interacted with each other during the exhaust system mode transition. The exhaust system thrust coefficient varied from 0.9288 to 0.9657 during the process. The CFD simulation results agree well with the experimental data, which demonstrated that the CFD methods were effective in evaluating the aerodynamic performance of the TBCC exhaust system during the mode transition.

Development and validation of a questionnaire designed to measure foot-health status.

Science.gov (United States)

Bennett, P J; Patterson, C; Wearing, S; Baglioni, T

1998-09-01

The aim of this study was to apply the principles of content, criterion, and construct validation to a new questionnaire specifically designed to measure foot-health status. One hundred eleven subjects completed two different questionnaires designed to measure foot health (the new Foot Health Status Questionnaire and the previously validated Foot Function Index) and underwent a clinical examination in order to provide data for a second-order confirmatory factor analysis. Presented herein is a psychometrically evaluated questionnaire that contains 13 items covering foot pain, foot function, footwear, and general foot health. The tool demonstrates a high degree of content, criterion, and construct validity and test-retest reliability.

Optimal Experimental Design for Model Discrimination

Science.gov (United States)

Myung, Jay I.; Pitt, Mark A.

2009-01-01

Models of a psychological process can be difficult to discriminate experimentally because it is not easy to determine the values of the critical design variables (e.g., presentation schedule, stimulus structure) that will be most informative in differentiating them. Recent developments in sampling-based search methods in statistics make it…

An Experimentally Validated Numerical Modeling Technique for Perforated Plate Heat Exchangers.

Science.gov (United States)

White, M J; Nellis, G F; Kelin, S A; Zhu, W; Gianchandani, Y

2010-11-01

Cryogenic and high-temperature systems often require compact heat exchangers with a high resistance to axial conduction in order to control the heat transfer induced by axial temperature differences. One attractive design for such applications is a perforated plate heat exchanger that utilizes high conductivity perforated plates to provide the stream-to-stream heat transfer and low conductivity spacers to prevent axial conduction between the perforated plates. This paper presents a numerical model of a perforated plate heat exchanger that accounts for axial conduction, external parasitic heat loads, variable fluid and material properties, and conduction to and from the ends of the heat exchanger. The numerical model is validated by experimentally testing several perforated plate heat exchangers that are fabricated using microelectromechanical systems based manufacturing methods. This type of heat exchanger was investigated for potential use in a cryosurgical probe. One of these heat exchangers included perforated plates with integrated platinum resistance thermometers. These plates provided in situ measurements of the internal temperature distribution in addition to the temperature, pressure, and flow rate measured at the inlet and exit ports of the device. The platinum wires were deposited between the fluid passages on the perforated plate and are used to measure the temperature at the interface between the wall material and the flowing fluid. The experimental testing demonstrates the ability of the numerical model to accurately predict both the overall performance and the internal temperature distribution of perforated plate heat exchangers over a range of geometry and operating conditions. The parameters that were varied include the axial length, temperature range, mass flow rate, and working fluid.

Design and Fabrication of an Experimental Microheater Array Powder Sintering Printer

Science.gov (United States)

Holt, Nicholas; Zhou, Wenchao

2018-03-01

Microheater array powder sintering (MAPS) is a novel additive manufacturing process that uses an array of microheaters to selectively sinter powder particles. MAPS shows great promise as a new method of printing flexible electronics by enabling digital curing of conductive inks on a variety of substrates. For MAPS to work effectively, a microscale air gap needs to be maintained between the heater array and the conductive ink. In this article, we present an experimental MAPS printer with air gap control for printing conductive circuits. First, we discuss design aspects necessary to implement MAPS. An analysis is performed to validate that the design can maintain the desired air gap between the microheaters and the sintering layer, which consists of a silver nanoparticle ink. The printer is tested by printing conductive lines on a flexible plastic substrate with silver nanoparticle ink. Results show MAPS performs on par with or better than the existing fabrication methods for printed electronics in terms of both the print quality (conductivity of the printed line) and print speed, which shows MAPS' great promise as a competitive new method for digital production of printed electronics.

An experimental design approach for optimization of spectrophotometric method for estimation of cefixime trihydrate using ninhydrin as derivatizing reagent in bulk and pharmaceutical formulation

Directory of Open Access Journals (Sweden)

Yogita B. Wani

2017-01-01

Full Text Available The aim of the present work is to use experimental design to screen and optimize experimental variables for developing a spectrophotometric method for determining cefixime trihydrate content using ninhydrin as a derivatizing reagent. The method is based on the reaction of the amino group of cefixime with ninhydrin in an alkaline medium to form a yellow-colored derivative (λmax 436 nm. A two-level full factorial design was utilized to screen the effect of ninhydrin reagent concentration (X1, volume of ninhydrin reagent (X2, heating temperature (X3 and heating time (X4 on the formation of the cefixime–ninhydrin complex Y (absorbance. One way ANOVA and Pareto ranking analyses have shown that the ninhydrin reagent concentration (X1, volume of ninhydrin reagent (X2 and heating temperature (X3 were statistically significant factors (P < 0.05 affecting the formation of the cefixime–ninhydrin complex Y (absorbance. A Box-Behnken experimental design with response surface methodology was then utilized to evaluate the main, interaction and quadratic effects of these three factors on the selected response. With the help of a response surface plot and contour plot the optimum values of the selected factors were determined and used for further experiments. These values were a ninhydrin reagent concentration (X1 of 0.2% w/v, volume of ninhydrin reagent (X2 of 1 mL and heating temperature (X3 of 80 °C. The proposed method was validated according to the ICH Q2 (R1 method validation guidelines. The results of the present study have clearly shown that an experimental design concept may be effectively applied to the optimization of a spectrophotometric method for estimating the cefixime trihydrate content in bulk and pharmaceutical formulation with the least number of experimental runs possible.

An experimentally validated model for geometrically nonlinear plucking-based frequency up-conversion in energy harvesting

Science.gov (United States)

Kathpalia, B.; Tan, D.; Stern, I.; Erturk, A.

2018-01-01

It is well known that plucking-based frequency up-conversion can enhance the power output in piezoelectric energy harvesting by enabling cyclic free vibration at the fundamental bending mode of the harvester even for very low excitation frequencies. In this work, we present a geometrically nonlinear plucking-based framework for frequency up-conversion in piezoelectric energy harvesting under quasistatic excitations associated with low-frequency stimuli such as walking and similar rigid body motions. Axial shortening of the plectrum is essential to enable plucking excitation, which requires a nonlinear framework relating the plectrum parameters (e.g. overlap length between the plectrum and harvester) to the overall electrical power output. Von Kármán-type geometrically nonlinear deformation of the flexible plectrum cantilever is employed to relate the overlap length between the flexible (nonlinear) plectrum and the stiff (linear) harvester to the transverse quasistatic tip displacement of the plectrum, and thereby the tip load on the linear harvester in each plucking cycle. By combining the nonlinear plectrum mechanics and linear harvester dynamics with two-way electromechanical coupling, the electrical power output is obtained directly in terms of the overlap length. Experimental case studies and validations are presented for various overlap lengths and a set of electrical load resistance values. Further analysis results are reported regarding the combined effects of plectrum thickness and overlap length on the plucking force and harvested power output. The experimentally validated nonlinear plectrum-linear harvester framework proposed herein can be employed to design and optimize frequency up-conversion by properly choosing the plectrum parameters (geometry, material, overlap length, etc) as well as the harvester parameters.

Energy performance of a ventilated façade by simulation with experimental validation

International Nuclear Information System (INIS)

Aparicio-Fernández, Carolina; Vivancos, José-Luis; Ferrer-Gisbert, Pablo; Royo-Pastor, Rafael

2014-01-01

A model for a building with ventilated façade was created using the software tool TRNSYS, version 17, and airflow parameters were simulated using TRNFlow. The results obtained with the model are compared and validated with experimental data. The temperature distribution along the air cavity was analysed and a chimney effect was observed, which produced the highest temperature gradient on the first floor. The heat flux of the external wall was analysed, and greater temperatures were observed on the external layer and inside the cavity. The model allows to calculate the energy demand of the building façade proposing and evaluating passive strategies. The corresponding office building for computer laboratories located in Valencia (Spain), was monitored for a year. The thermal behaviour of the floating external sheet was analysed using an electronic panel designed for the reading and storage of data. A feasibility study of the recovery of hot air inside the façade into the building was performed. The results obtained showed a lower heating demand when hot air is introduced inside the building, increasing the efficiency of heat recovery equipment. - Highlights: •An existing office building was monitored for a year. •A model of a ventilated façade by TRNSYS simulation tool was validated. •Air flow parameters inside the ventilated façade were identified. •Recovery of the hot air inside the façade for input into the building was studied

Design and experimentation of BSFQ logic devices

International Nuclear Information System (INIS)

Hosoki, T.; Kodaka, H.; Kitagawa, M.; Okabe, Y.

1999-01-01

Rapid single flux quantum (RSFQ) logic needs synchronous pulses for each gate, so the clock-wiring problem is more serious when designing larger scale circuits with this logic. So we have proposed a new SFQ logic which follows Boolean algebra perfectly by using set and reset pulses. With this logic, the level information of current input is transmitted with these pulses generated by level-to-pulse converters, and each gate calculates logic using its phase level made by these pulses. Therefore, our logic needs no clock in each gate. We called this logic 'Boolean SFQ (BSFQ) logic'. In this paper, we report design and experimentation for an AND gate with inverting input based on BSFQ logic. The experimental results for OR and XOR gates are also reported. (author)

Engineering Software Suite Validates System Design

Science.gov (United States)

2007-01-01

EDAptive Computing Inc.'s (ECI) EDAstar engineering software tool suite, created to capture and validate system design requirements, was significantly funded by NASA's Ames Research Center through five Small Business Innovation Research (SBIR) contracts. These programs specifically developed Syscape, used to capture executable specifications of multi-disciplinary systems, and VectorGen, used to automatically generate tests to ensure system implementations meet specifications. According to the company, the VectorGen tests considerably reduce the time and effort required to validate implementation of components, thereby ensuring their safe and reliable operation. EDASHIELD, an additional product offering from ECI, can be used to diagnose, predict, and correct errors after a system has been deployed using EDASTAR -created models. Initial commercialization for EDASTAR included application by a large prime contractor in a military setting, and customers include various branches within the U.S. Department of Defense, industry giants like the Lockheed Martin Corporation, Science Applications International Corporation, and Ball Aerospace and Technologies Corporation, as well as NASA's Langley and Glenn Research Centers

Online optimal experimental re-design in robotic parallel fed-batch cultivation facilities.

Science.gov (United States)

Cruz Bournazou, M N; Barz, T; Nickel, D B; Lopez Cárdenas, D C; Glauche, F; Knepper, A; Neubauer, P

2017-03-01

We present an integrated framework for the online optimal experimental re-design applied to parallel nonlinear dynamic processes that aims to precisely estimate the parameter set of macro kinetic growth models with minimal experimental effort. This provides a systematic solution for rapid validation of a specific model to new strains, mutants, or products. In biosciences, this is especially important as model identification is a long and laborious process which is continuing to limit the use of mathematical modeling in this field. The strength of this approach is demonstrated by fitting a macro-kinetic differential equation model for Escherichia coli fed-batch processes after 6 h of cultivation. The system includes two fully-automated liquid handling robots; one containing eight mini-bioreactors and another used for automated at-line analyses, which allows for the immediate use of the available data in the modeling environment. As a result, the experiment can be continually re-designed while the cultivations are running using the information generated by periodical parameter estimations. The advantages of an online re-computation of the optimal experiment are proven by a 50-fold lower average coefficient of variation on the parameter estimates compared to the sequential method (4.83% instead of 235.86%). The success obtained in such a complex system is a further step towards a more efficient computer aided bioprocess development. Biotechnol. Bioeng. 2017;114: 610-619. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Using IMPRINT to Guide Experimental Design with Simulated Task Environments

Science.gov (United States)

2015-06-18

USING IMPRINT TO GUIDE EXPERIMENTAL DESIGN OF SIMULATED TASK ENVIRONMENTS THESIS Gregory...ENG-MS-15-J-052 USING IMPRINT TO GUIDE EXPERIMENTAL DESIGN WITH SIMULATED TASK ENVIRONMENTS THESIS Presented to the Faculty Department...Civilian, USAF June 2015 DISTRIBUTION STATEMENT A. APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED. AFIT-ENG-MS-15-J-052 USING IMPRINT

Experimental design and reporting standards for improving the internal validity of pre-clinical studies in the field of pain: Consensus of the IMI-Europain consortium

DEFF Research Database (Denmark)

Knopp, K.L.; Stenfors, C.; Baastrup, Cathrine Søndergaard

2015-01-01

that recommendations on how to improve these factors are warranted. Methods Members of Europain, a pain research consortium funded by the European Innovative Medicines Initiative (IMI), developed internal recommendations on how to improve the reliability of pre-clinical studies between laboratories. This guidance...... and conduct, and data analysis and interpretation. Key principles such as sample size calculation, a priori definition of a primary efficacy measure, randomization, allocation concealments, and blinding are discussed. In addition, considerations of how stress and normal rodent physiology impact outcome...... development in order to estimate possible publication bias is discussed. Conclusions More systematic research is needed to analyze how inadequate internal validity and/or experimental bias may impact reproducibility across pre-clinical pain studies. Addressing the potential threats to internal validity...

Optimizing an experimental design for an electromagnetic experiment

Science.gov (United States)

Roux, Estelle; Garcia, Xavier

2013-04-01

Most of geophysical studies focus on data acquisition and analysis, but another aspect which is gaining importance is the discussion on acquisition of suitable datasets. This can be done through the design of an optimal experiment. Optimizing an experimental design implies a compromise between maximizing the information we get about the target and reducing the cost of the experiment, considering a wide range of constraints (logistical, financial, experimental …). We are currently developing a method to design an optimal controlled-source electromagnetic (CSEM) experiment to detect a potential CO2 reservoir and monitor this reservoir during and after CO2 injection. Our statistical algorithm combines the use of linearized inverse theory (to evaluate the quality of one given design via the objective function) and stochastic optimization methods like genetic algorithm (to examine a wide range of possible surveys). The particularity of our method is that it uses a multi-objective genetic algorithm that searches for designs that fit several objective functions simultaneously. One main advantage of this kind of technique to design an experiment is that it does not require the acquisition of any data and can thus be easily conducted before any geophysical survey. Our new experimental design algorithm has been tested with a realistic one-dimensional resistivity model of the Earth in the region of study (northern Spain CO2 sequestration test site). We show that a small number of well distributed observations have the potential to resolve the target. This simple test also points out the importance of a well chosen objective function. Finally, in the context of CO2 sequestration that motivates this study, we might be interested in maximizing the information we get about the reservoir layer. In that case, we show how the combination of two different objective functions considerably improve its resolution.

Design and Experimental Study on Spinning Solid Rocket Motor

Science.gov (United States)

Xue, Heng; Jiang, Chunlan; Wang, Zaicheng

The study on spinning solid rocket motor (SRM) which used as power plant of twice throwing structure of aerial submunition was introduced. This kind of SRM which with the structure of tangential multi-nozzle consists of a combustion chamber, propellant charge, 4 tangential nozzles, ignition device, etc. Grain design, structure design and prediction of interior ballistic performance were described, and problem which need mainly considered in design were analyzed comprehensively. Finally, in order to research working performance of the SRM, measure pressure-time curve and its speed, static test and dynamic test were conducted respectively. And then calculated values and experimental data were compared and analyzed. The results indicate that the designed motor operates normally, and the stable performance of interior ballistic meet demands. And experimental results have the guidance meaning for the pre-research design of SRM.

Vortex-Concept for Radioactivity Release Prevention at NPP: Development of Computational Model of Lab-Scale Experimental Setup

Energy Technology Data Exchange (ETDEWEB)

Ullah, Sana; Sung, Yim Man; Park, Jin Soo; Sung Hyung Jin [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The experimental validation of the vortex-like air curtain concept and use of an appropriate CFD modelling approach for analyzing the problem becomes crucial. A lab-scale experimental setup is designed to validate the proposed concept and CFD modeling approach as a part of validation process. In this study, a computational model of this lab-scale experiment setup is developed using open source CFD code OpenFOAM. The computational results will be compared with experimental data for validation purposes in future, when experimental data is available. 1) A computation model of a lab-scale experimental setup, designed to validate the concept of artificial vortex-like airflow generation for application to radioactivity dispersion prevention in the event of severe accident, was developed. 2) The mesh sensitivity study was performed and a mesh of about 2 million cells was found to be sufficient for this setup.

Improved Titanium Billet Inspection Sensitivity through Optimized Phased Array Design, Part II: Experimental Validation and Comparative Study with Multizone

International Nuclear Information System (INIS)

Hassan, W.; Vensel, F.; Knowles, B.; Lupien, V.

2006-01-01

The inspection of critical rotating components of aircraft engines has made important advances over the last decade. The development of Phased Array (PA) inspection capability for billet and forging materials used in the manufacturing of critical engine rotating components has been a priority for Honeywell Aerospace. The demonstration of improved PA inspection system sensitivity over what is currently used at the inspection houses is a critical step in the development of this technology and its introduction to the supply base as a production inspection. As described in Part I (in these proceedings), a new phased array transducer was designed and manufactured for optimal inspection of eight inch diameter Ti-6Al-4V billets. After confirming that the transducer was manufactured in accordance with the design specifications a validation study was conducted to assess the sensitivity improvement of the PAI over the current capability of Multi-zone (MZ) inspection. The results of this study confirm the significant (≅ 6 dB in FBH number sign sensitivity) improvement of the PAI sensitivity over that of MZI

Experimental and Numerical Analysis of S-CO{sub 2} Critical Flow for SFR Recovery System Design

Energy Technology Data Exchange (ETDEWEB)

Kim, Min Seok; Jung, Hwa-Young; Ahn, Yoonhan; Lee, Jekyoung; Lee, Jeong Ik [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2016-05-15

This paper presents both numerical and experimental studies of the critical flow of S-CO{sub 2} while special attention is given to the turbo-machinery seal design. A computational critical flow model is described first. The experiments were conducted to validate the critical flow model. Various conditions have been tested to study the flow characteristic and provide validation data for the model. The comparison of numerical and experimental results of S-CO{sub 2} critical flow will be presented. In order to eliminate SWR, a concept of coupling the Supercritical CO{sub 2} (S-CO{sub 2}) cycle with SFR has been proposed. It is known that for a closed system controlling the inventory is important for stable operation and achieving high efficiency. Since the S-CO{sub 2} power cycle is a highly pressurized system, certain amount of leakage flow is inevitable in the rotating turbo-machinery via seals. To simulate the CO{sub 2} leak flow in a turbo-machinery with higher accuracy in the future, the real gas effect and friction factor will be considered for the CO{sub 2} critical flow model. Moreover, experimentally obtained temperature data were somewhat different from the numerically obtained temperature due to the insufficient insulation and large thermal inertia of the CO{sub 2} critical flow facility. Insulation in connecting pipes and the low-pressure tank will be added and additional tests will be conducted.

External gear pumps operating with non-Newtonian fluids: Modelling and experimental validation

Science.gov (United States)

Rituraj, Fnu; Vacca, Andrea

2018-06-01

External Gear Pumps are used in various industries to pump non-Newtonian viscoelastic fluids like plastics, paints, inks, etc. For both design and analysis purposes, it is often a matter of interest to understand the features of the displacing action realized by meshing of the gears and the description of the behavior of the leakages for this kind of pumps. However, very limited work can be found in literature about methodologies suitable to model such phenomena. This article describes the technique of modelling external gear pumps that operate with non-Newtonian fluids. In particular, it explains how the displacing action of the unit can be modelled using a lumped parameter approach which involves dividing fluid domain into several control volumes and internal flow connections. This work is built upon the HYGESim simulation tool, conceived by the authors' research team in the last decade, which is for the first time extended for the simulation of non-Newtonian fluids. The article also describes several comparisons between simulation results and experimental data obtained from numerous experiments performed for validation of the presented methodology. Finally, operation of external gear pump with fluids having different viscosity characteristics is discussed.

Thermal-hydraulic codes validation for safety analysis of NPPs with RBMK

International Nuclear Information System (INIS)

Brus, N.A.; Ioussoupov, O.E.

2000-01-01

This work is devoted to validation of western thermal-hydraulic codes (RELAP5/MOD3 .2 and ATHLET 1.1 Cycle C) in application to Russian designed light water reactors. Such validation is needed due to features of RBMK reactor design and thermal-hydraulics in comparison with PWR and BWR reactors, for which these codes were developed and validated. These validation studies are concluded with a comparison of calculation results of modeling with the thermal-hydraulics codes with the experiments performed earlier using the thermal-hydraulics test facilities with the experimental data. (authors)

Method for Determining Volumetric Efficiency and Its Experimental Validation

Directory of Open Access Journals (Sweden)

Ambrozik Andrzej

2017-12-01

Full Text Available Modern means of transport are basically powered by piston internal combustion engines. Increasingly rigorous demands are placed on IC engines in order to minimise the detrimental impact they have on the natural environment. That stimulates the development of research on piston internal combustion engines. The research involves experimental and theoretical investigations carried out using computer technologies. While being filled, the cylinder is considered to be an open thermodynamic system, in which non-stationary processes occur. To make calculations of thermodynamic parameters of the engine operating cycle, based on the comparison of cycles, it is necessary to know the mean constant value of cylinder pressure throughout this process. Because of the character of in-cylinder pressure pattern and difficulties in pressure experimental determination, in the present paper, a novel method for the determination of this quantity was presented. In the new approach, the iteration method was used. In the method developed for determining the volumetric efficiency, the following equations were employed: the law of conservation of the amount of substance, the first law of thermodynamics for open system, dependences for changes in the cylinder volume vs. the crankshaft rotation angle, and the state equation. The results of calculations performed with this method were validated by means of experimental investigations carried out for a selected engine at the engine test bench. A satisfactory congruence of computational and experimental results as regards determining the volumetric efficiency was obtained. The method for determining the volumetric efficiency presented in the paper can be used to investigate the processes taking place in the cylinder of an IC engine.

Experimental Validation of the Simulation Model of a DOAS Equipped with a Desiccant Wheel and a Vapor Compression Refrigeration System

Directory of Open Access Journals (Sweden)

Pedro J. Martínez

2017-09-01

Full Text Available A dedicated outdoor air system (DOAS can be designed to supply 100% of the outside air and meet the latent load of the room with dry air. The objectives of this study were to develop a model of a DOAS equipped with a desiccant wheel and a vapor-compression refrigeration system, build a prototype, validate the model with experimental data, and gain knowledge about the system operation. The test facility was designed with the desiccant wheel downstream of the cooling coil to take advantage of the operating principles of cooling coils and desiccants. A model of the DOAS was developed in the TRNSYS environment. The root mean standard error (RMSE was used for model validation by comparing the measured air and refrigerant properties with the corresponding calculated values. The results obtained with the developed model showed that the DOAS was able to maintain an indoor humidity ratio depending on outdoor conditions. Laboratory tests were also used to investigate the effect of changes in the regeneration air temperature and the process airflow rate on the process air humidity ratio at the outlet of the wheel. The results are consistent with the technical literature.

Experimental validation of a rate-based model for CO2 capture using an AMP solution

DEFF Research Database (Denmark)

Gabrielsen, Jostein; Svendsen, H. F.; Michelsen, Michael Locht

2007-01-01

Detailed experimental data, including temperature profiles over the absorber, for a carbon dioxide (CO"2) absorber with structured packing in an integrated laboratory pilot plant using an aqueous 2-amino-2-methyl-1-propanol (AMP) solution are presented. The experimental gas-liquid material balance...... was within an average of 3.5% for the experimental conditions presented. A predictive rate-based steady-state model for CO"2 absorption into an AMP solution, using an implicit expression for the enhancement factor, has been validated against the presented pilot plant data. Furthermore, a parameter...

Experimental validation of calculated capture rate for nucleus involved in fuel cycle

International Nuclear Information System (INIS)

Benslimane-Bouland, A.

1997-09-01

The framework of this study was the evaluation of the nuclear data requirements for Actinides and Fission Products applied to current nuclear reactors as well as future applications. This last item includes extended irradiation campaigns, 100 % Mixed Oxide fuel, transmutation or even incineration. The first part of this study presents different types of integral measurements which are available for capture rate measurements, as well as the methods used for reactor core calculation route design and nuclear data library validation. The second section concerns the analysis of three specific irradiation experiments. The results have shown the extent of the current knowledge on nuclear data as well as the associated uncertainties. The third and last section shows both the coherency between all the results, and the statistical method applied for nuclear data library adjustment. A relevant application of this method has demonstrated that only specifically chosen integral experiments can be of use for the validation of nuclear data libraries. The conclusion is reached that even if co-ordinated efforts between reactor and nuclear physicists have made possible a huge improvement in the knowledge of capture cross sections of the main nuclei such as uranium and plutonium, some improvements are currently necessary for the minor actinides (Np, Am and Cm). Both integral and differential measurements are recommended to improve the knowledge of minor actinide cross sections. As far as integral experiments are concerned, a set of criteria to be followed during the experimental conception have been defined in order to both reduce the number of required calculation approximations, and to increase as much as possible the maximum amount of extracted information. (author)

Experimental validation of the fluid–structure interaction simulation of a bioprosthetic aortic heart valve

International Nuclear Information System (INIS)

Kemp, I.; Dellimore, K.; Rodriguez, R.; Scheffer, C.; Blaine, D.; Weich, H.; Doubell, A.

2013-01-01

Experiments performed on a 19 mm diameter bioprosthetic valve were used to successfully validate the fluid–structure interaction (FSI) simulation of an aortic valve at 72 bpm. The FSI simulation was initialized via a novel approach utilizing a Doppler sonogram of the experimentally tested valve. Using this approach very close quantitative agreement (≤12.5 %) between the numerical predictions and experimental values for several key valve performance parameters, including the peak systolic transvalvular pressure gradient, rapid valve opening time and rapid valve closing time, was obtained. The predicted valve leaflet kinematics during opening and closing were also in good agreement with the experimental measurements.

LATUX: An Iterative Workflow for Designing, Validating, and Deploying Learning Analytics Visualizations

Science.gov (United States)

Martinez-Maldonado, Roberto; Pardo, Abelardo; Mirriahi, Negin; Yacef, Kalina; Kay, Judy; Clayphan, Andrew

2015-01-01

Designing, validating, and deploying learning analytics tools for instructors or students is a challenge that requires techniques and methods from different disciplines, such as software engineering, human-computer interaction, computer graphics, educational design, and psychology. Whilst each has established its own design methodologies, we now…

The difference between traditional experiments and CFD validation benchmark experiments

Energy Technology Data Exchange (ETDEWEB)

Smith, Barton L., E-mail: barton.smith@usu.edu

2017-02-15

Computation Fluid Dynamics provides attractive features for design, and perhaps licensing, of nuclear power plants. The most important of these features is low cost compared to experiments. However, uncertainty of CFD calculations must accompany these calculations in order for the results to be useful for important decision making. In order to properly assess the uncertainty of a CFD calculation, it must be “validated” against experimental data. Unfortunately, traditional “discovery” experiments are normally ill-suited to provide all of the information necessary for the validation exercise. Traditionally, experiments are performed to discover new physics, determine model parameters, or to test designs. This article will describe a new type of experiment; one that is designed and carried out with the specific purpose of providing Computational Fluid Dynamics (CFD) validation benchmark data. We will demonstrate that the goals of traditional experiments and validation experiments are often in conflict, making use of traditional experimental results problematic and leading directly to larger predictive uncertainty of the CFD model.

The difference between traditional experiments and CFD validation benchmark experiments

International Nuclear Information System (INIS)

Smith, Barton L.

2017-01-01

Computation Fluid Dynamics provides attractive features for design, and perhaps licensing, of nuclear power plants. The most important of these features is low cost compared to experiments. However, uncertainty of CFD calculations must accompany these calculations in order for the results to be useful for important decision making. In order to properly assess the uncertainty of a CFD calculation, it must be “validated” against experimental data. Unfortunately, traditional “discovery” experiments are normally ill-suited to provide all of the information necessary for the validation exercise. Traditionally, experiments are performed to discover new physics, determine model parameters, or to test designs. This article will describe a new type of experiment; one that is designed and carried out with the specific purpose of providing Computational Fluid Dynamics (CFD) validation benchmark data. We will demonstrate that the goals of traditional experiments and validation experiments are often in conflict, making use of traditional experimental results problematic and leading directly to larger predictive uncertainty of the CFD model.

Computational Modelling of Patella Femoral Kinematics During Gait Cycle and Experimental Validation

Science.gov (United States)

Maiti, Raman

2016-06-01

The effect of loading and boundary conditions on patellar mechanics is significant due to the complications arising in patella femoral joints during total knee replacements. To understand the patellar mechanics with respect to loading and motion, a computational model representing the patella femoral joint was developed and validated against experimental results. The computational model was created in IDEAS NX and simulated in MSC ADAMS/VIEW software. The results obtained in the form of internal external rotations and anterior posterior displacements for a new and experimentally simulated specimen for patella femoral joint under standard gait condition were compared with experimental measurements performed on the Leeds ProSim knee simulator. A good overall agreement between the computational prediction and the experimental data was obtained for patella femoral kinematics. Good agreement between the model and the past studies was observed when the ligament load was removed and the medial lateral displacement was constrained. The model is sensitive to ±5 % change in kinematics, frictional, force and stiffness coefficients and insensitive to time step.

Design and experimental investigation of a magnetically coupled vibration energy harvester using two inverted piezoelectric cantilever beams for rotational motion

International Nuclear Information System (INIS)

Zou, Hong-Xiang; Zhang, Wen-ming; Li, Wen-Bo; Wei, Ke-Xiang; Gao, Qiu-Hua; Peng, Zhi-Ke; Meng, Guang

2017-01-01

Highlights: • A magnetically coupled two-degree-of-freedom harvester for rotation is proposed. • The electromechanical coupling model is developed and validated experimentally. • The harvester can generate high voltage at low rotating speeds. • The harvester can harvest vibration energy in multiple frequency bands. - Abstract: Energy can be harvested from rotational motion for powering wireless autonomous electronic devices. The paper presents a magnetically coupled two-degree-of-freedom vibration energy harvester for rotary motion applications. The design consists of two inverted piezoelectric cantilever beams whose free ends point to the rotating shaft. The centrifugal force of the inverted cantilever beam is beneficial to producing large amplitude in a low speed range. The electromechanical coupling dynamical model is developed by the energy method from Hamilton’s principle and validated experimentally. The experimental results indicate that the presented harvester is suitable for low speed rotation and can harvest vibration energy in multiple frequency bands. The first and second resonant behaviors of voltage can be obtained at 420 r/min and 550 r/min, and the average output powers are 564 μW and 535.3 μW, respectively.

Neutronics experimental validation of the Jules Horowitz reactor fuel by interpretation of the VALMONT experimental program-transposition of the uncertainties on the reactivity of JHR with JEF2.2 and JEFF3.1.1

International Nuclear Information System (INIS)

Leray, O.; Hudelot, J.P.; Doederlein, C.; Vaglio-Gaudard, C.; Antony, M.; Santamarina, A.; Bernard, D.

2012-01-01

The new European material testing Jules Horowitz Reactor (JHR), currently under construction in Cadarache center (CEA France), will use LEU (20% enrichment in 235 U) fuels (U 3 Si 2 for the start up and UMoAl in the future) which are quite different from the industrial oxide fuel, for which an extensive neutronics experimental validation database has been established. The HORUS3D/N neutronics calculation scheme, used for the design and safety studies of the JHR, is being developed within the framework of a rigorous verification-numerical validation-experimental validation methodology. In this framework, the experimental VALMONT (Validation of Aluminium Molybdenum uranium fuel for Neutronics) program has been performed in the MINERVE facility of CEA Cadarache (France), in order to qualify the capability of HORUS3D/N to accurately calculate the reactivity of the JHR reactor. The MINERVE facility using the oscillation technique provides accurate measurements of reactivity effect of samples. The VALMONT program includes oscillations of samples of UAl ∞ /Al and UMo/Al with enrichments ranging from 0.2% to 20% and Uranium densities from 2.2 to 8 g/cm 3 . The geometry of the samples and the pitch of the experimental lattice ensure maximum representativeness with the neutron spectrum expected for JHR. By comparing the effect of the sample with the one of a known fuel specimen, the reactivity effect can be measured in absolute terms and be compared to computational results. Special attention was paid to the rigorous determination and reduction of the experimental uncertainties. The calculational analysis of the VALMONT results was performed with the French deterministic code APOLLO2. A comparison of the impact of the different calculation methods, data libraries and energy meshes that were tested is presented. The interpretation of the VALMONT experimental program allowed the experimental validation of JHR fuel UMoAl8 (with an enrichment of 19.75% 235 U) by the Minerve

HYDROïD humanoid robot head with perception and emotion capabilities :Modeling, Design and Experimental Results

Directory of Open Access Journals (Sweden)

Samer eAlfayad

2016-04-01

Full Text Available In the framework of the HYDROïD humanoid robot project, this paper describes the modeling and design of an electrically actuated head mechanism. Perception and emotion capabilities are considered in the design process. Since HYDROïD humanoid robot is hydraulically actuated, the choice of electrical actuation for the head mechanism addressed in this paper is justified. Considering perception and emotion capabilities leads to a total number of 15 degrees of freedom for the head mechanism which are split on four main sub-mechanisms: the neck, the mouth, the eyes and the eyebrows. Biological data and kinematics performances of human head are taken as inputs of the design process. A new solution of uncoupled eyes is developed to possibly address the master-slave process that links the human eyes as well as vergence capabilities. Modeling each sub-system is carried out in order to get equations of motion, their frequency responses and their transfer functions. The neck pitch rotation is given as a study example. Then, the head mechanism performances are presented through a comparison between model and experimental results validating the hardware capabilities. Finally, the head mechanism is integrated on the HYDROïD upper-body. An object tracking experiment coupled with emotional expressions is carried out to validate the synchronization of the eye rotations with the body motions.

Toward experimental international business : Unraveling fundamental causal linkages

NARCIS (Netherlands)

van Witteloostuijn, Arjen

2015-01-01

Purpose – The purpose of this paper is to argue that the time is ripe to establish a powerful tradition in Experimental International Business (IB). Probably due to what the Arjen van Witteloostuijn refers to as the external validity myth, experimental laboratory designs are underutilized in IB,

Experimental validation of TASS/SMR-S critical flow model for the integral reactor SMART

Energy Technology Data Exchange (ETDEWEB)

Seo, Si Won; Ra, In Sik; Kim, Kun Yeup [ACT Co., Daejeon (Korea, Republic of); Chung, Young Jong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2011-05-15

An advanced integral PWR, SMART (System- Integrated Modular Advanced ReacTor) is being developed in KAERI. It has a compact size and a relatively small power rating (330MWt) compared to a conventional reactor. Because new concepts are applied to SMART, an experimental and analytical validation is necessary for the safety evaluation of SMART. The analytical safety validation is being accomplished by a safety analysis code for an integral reactor, TASS/SMR-S developed by KAERI. TASS/SMR-S uses a lumped parameter one dimensional node and path modeling for the thermal hydraulic calculation and it uses point kinetics for the reactor power calculation. It has models for a general usage such as a core heat transfer model, a wall heat structure model, a critical flow model, component models, and it also has many SMART specific models such as an once through helical coiled steam generator model, and a condensate heat transfer model. To ensure that the TASS/SMR-S code has the calculation capability for the safety evaluation of SMART, the code should be validated for the specific models with the separate effect test experimental results. In this study, TASS/SMR-S critical flow model is evaluated as compared with SMD (Super Moby Dick) experiment

Design and Control of Compliant Tensegrity Robots Through Simulation and Hardware Validation

Science.gov (United States)

Caluwaerts, Ken; Despraz, Jeremie; Iscen, Atil; Sabelhaus, Andrew P.; Bruce, Jonathan; Schrauwen, Benjamin; Sunspiral, Vytas

2014-01-01

To better understand the role of tensegrity structures in biological systems and their application to robotics, the Dynamic Tensegrity Robotics Lab at NASA Ames Research Center has developed and validated two different software environments for the analysis, simulation, and design of tensegrity robots. These tools, along with new control methodologies and the modular hardware components developed to validate them, are presented as a system for the design of actuated tensegrity structures. As evidenced from their appearance in many biological systems, tensegrity ("tensile-integrity") structures have unique physical properties which make them ideal for interaction with uncertain environments. Yet these characteristics, such as variable structural compliance, and global multi-path load distribution through the tension network, make design and control of bio-inspired tensegrity robots extremely challenging. This work presents the progress in using these two tools in tackling the design and control challenges. The results of this analysis includes multiple novel control approaches for mobility and terrain interaction of spherical tensegrity structures. The current hardware prototype of a six-bar tensegrity, code-named ReCTeR, is presented in the context of this validation.

Optimizing Nuclear Reaction Analysis (NRA) using Bayesian Experimental Design

International Nuclear Information System (INIS)

Toussaint, Udo von; Schwarz-Selinger, Thomas; Gori, Silvio

2008-01-01

Nuclear Reaction Analysis with 3 He holds the promise to measure Deuterium depth profiles up to large depths. However, the extraction of the depth profile from the measured data is an ill-posed inversion problem. Here we demonstrate how Bayesian Experimental Design can be used to optimize the number of measurements as well as the measurement energies to maximize the information gain. Comparison of the inversion properties of the optimized design with standard settings reveals huge possible gains. Application of the posterior sampling method allows to optimize the experimental settings interactively during the measurement process.

Experimental validation of UTDefect

Energy Technology Data Exchange (ETDEWEB)

Eriksson, A.S. [ABB Tekniska Roentgencentralen AB, Taeby (Sweden); Bostroem, A.; Wirdelius, H. [Chalmers Univ. of Technology, Goeteborg (Sweden). Div. of Mechanics

1997-01-01

This study reports on conducted experiments and computer simulations of ultrasonic nondestructive testing (NDT). Experiments and simulations are compared with the purpose of validating the simulation program UTDefect. UTDefect simulates ultrasonic NDT of cracks and some other defects in isotropic and homogeneous materials. Simulations for the detection of surface breaking cracks are compared with experiments in pulse-echo mode on surface breaking cracks in carbon steel plates. The echo dynamics are plotted and compared with the simulations. The experiments are performed on a plate with thickness 36 mm and the crack depths are 7.2 mm and 18 mm. L- and T-probes with frequency 1, 2 and 4 MHz and angels 45, 60 and 70 deg are used. In most cases the probe and the crack is on opposite sides of the plate, but in some cases they are on the same side. Several cracks are scanned from two directions. In total 53 experiments are reported for 33 different combinations. Generally the simulations agree well with the experiments and UTDefect is shown to be able to, within certain limits, perform simulations that are close to experiments. It may be concluded that: For corner echoes the eight 45 deg cases and the eight 60 deg cases show good agreement between experiments and UTDefect, especially for the 7.2 mm crack. The amplitudes differ more for some cases where the defect is close to the probe and for the corner of the 18 mm crack. For the two 70 deg cases there are too few experimental values to compare the curve shapes, but the amplitudes do not differ too much. The tip diffraction echoes also agree well in general. For some cases, where the defect is close to the probe, the amplitudes differ more than 10-15 dB, but for all but two cases the difference in amplitude is less than 7 dB. 6 refs.

Elasto-dynamic analysis of a gear pump-Part III: Experimental validation procedure and model extension to helical gears

Science.gov (United States)

Mucchi, E.; Dalpiaz, G.

2015-01-01

This work concerns external gear pumps for automotive applications, which operate at high speed and low pressure. In previous works of the authors (Part I and II, [1,2]), a non-linear lumped-parameter kineto-elastodynamic model for the prediction of the dynamic behaviour of external gear pumps was presented. It takes into account the most important phenomena involved in the operation of this kind of machine. The two main sources of noise and vibration are considered: pressure pulsation and gear meshing. The model has been used in order to foresee the influence of working conditions and design modifications on vibration generation. The model's experimental validation is a difficult task. Thus, Part III proposes a novel methodology for the validation carried out by the comparison of simulations and experimental results concerning forces and moments: it deals with the external and inertial components acting on the gears, estimated by the model, and the reactions and inertial components on the pump casing and the test plate, obtained by measurements. The validation is carried out comparing the level of the time synchronous average in the time domain and the waterfall maps in the frequency domain, with particular attention to identify system resonances. The validation results are satisfactory globally, but discrepancies are still present. Moreover, the assessed model has been properly modified for the application to a new virtual pump prototype with helical gears in order to foresee gear accelerations and dynamic forces. Part IV is focused on improvements in the modelling and analysis of the phenomena bound to the pressure evolution around the gears in order to achieve results closer to the measured values. As a matter of fact, the simulation results have shown that a variable meshing stiffness has a notable contribution on the dynamic behaviour of the pump but this is not as important as the pressure phenomena. As a consequence, the original model was modified with the

A methodology for the validated design space exploration of fuel cell powered unmanned aerial vehicles

Science.gov (United States)

Moffitt, Blake Almy

to carry a 2.2 kg payload with 24 hours of endurance. Uncertainty distributions for both design variables and the CAs were estimated based on experimental results and were found to dominate the design space. To reduce uncertainty and test the flexibility of the MDA framework, CAs were replaced with either empirical, or semi-empirical relationships during the optimization process. The final design was validated via a hardware-in-the loop simulation. Finally, the fuel cell UAV probabilistic design space was studied. A graphical representation of the design space was generated and the optima due to deterministic and probabilistic constraints were identified. The methodology was used to identify Pareto frontiers of the design space which were shown on contour plots of the design space. Unanticipated discontinuities of the Pareto fronts were observed as different constraints became active providing useful information on which to base design and development decisions.

Experimental validation of a true-scale morphing flap for large civil aircraft applications

Science.gov (United States)

Pecora, R.; Amoroso, F.; Arena, M.; Noviello, M. C.; Rea, F.

2017-04-01

Within the framework of the JTI-Clean Sky (CS) project, and during the first phase of the Low Noise Configuration Domain of the Green Regional Aircraft - Integrated Technological Demonstration (GRA-ITD, the preliminary design and technological demonstration of a novel wing flap architecture were addressed. Research activities were carried out to substantiate the feasibility of morphing concepts enabling flap camber variation in compliance with the demanding safety requirements applicable to the next generation green regional aircraft, 130- seats with open rotor configuration. The driving motivation for the investigation on such a technology was found in the opportunity to replace a conventional double slotted flap with a single slotted camber-morphing flap assuring similar high lift performances -in terms of maximum attainable lift coefficient and stall angle- while lowering emitted noise and system complexity. Studies and tests were limited to a portion of the flap element obtained by slicing the actual flap geometry with two cutting planes distant 0.8 meters along the wing span. Further activities were then addressed in order to increase the TRL of the validated architecture within the second phase of the CS-GRA. Relying upon the already assessed concept, an innovative and more advanced flap device was designed in order to enable two different morphing modes on the basis of the A/C flight condition / flap setting: Mode1, Overall camber morphing to enhance high-lift performances during take-off and landing (flap deployed); Mode2, Tab-like morphing mode. Upwards and downwards deflection of the flap tip during cruise (flap stowed) for load control at high speed. A true-scale segment of the outer wing flap (4 meters span with a mean chord of 0.9 meters) was selected as investigation domain for the new architecture in order to duly face the challenges posed by real wing installation. Advanced and innovative solutions for the adaptive structure, actuation and control

Rating the methodological quality of single-subject designs and n-of-1 trials: introducing the Single-Case Experimental Design (SCED) Scale.

Science.gov (United States)

Tate, Robyn L; McDonald, Skye; Perdices, Michael; Togher, Leanne; Schultz, Regina; Savage, Sharon

2008-08-01

Rating scales that assess methodological quality of clinical trials provide a means to critically appraise the literature. Scales are currently available to rate randomised and non-randomised controlled trials, but there are none that assess single-subject designs. The Single-Case Experimental Design (SCED) Scale was developed for this purpose and evaluated for reliability. Six clinical researchers who were trained and experienced in rating methodological quality of clinical trials developed the scale and participated in reliability studies. The SCED Scale is an 11-item rating scale for single-subject designs, of which 10 items are used to assess methodological quality and use of statistical analysis. The scale was developed and refined over a 3-year period. Content validity was addressed by identifying items to reduce the main sources of bias in single-case methodology as stipulated by authorities in the field, which were empirically tested against 85 published reports. Inter-rater reliability was assessed using a random sample of 20/312 single-subject reports archived in the Psychological Database of Brain Impairment Treatment Efficacy (PsycBITE). Inter-rater reliability for the total score was excellent, both for individual raters (overall ICC = 0.84; 95% confidence interval 0.73-0.92) and for consensus ratings between pairs of raters (overall ICC = 0.88; 95% confidence interval 0.78-0.95). Item reliability was fair to excellent for consensus ratings between pairs of raters (range k = 0.48 to 1.00). The results were replicated with two independent novice raters who were trained in the use of the scale (ICC = 0.88, 95% confidence interval 0.73-0.95). The SCED Scale thus provides a brief and valid evaluation of methodological quality of single-subject designs, with the total score demonstrating excellent inter-rater reliability using both individual and consensus ratings. Items from the scale can also be used as a checklist in the design, reporting and critical

Macroscopic Dynamic Modeling of Sequential Batch Cultures of Hybridoma Cells: An Experimental Validation

Directory of Open Access Journals (Sweden)

Laurent Dewasme

2017-02-01

Full Text Available Hybridoma cells are commonly grown for the production of monoclonal antibodies (MAb. For monitoring and control purposes of the bioreactors, dynamic models of the cultures are required. However these models are difficult to infer from the usually limited amount of available experimental data and do not focus on target protein production optimization. This paper explores an experimental case study where hybridoma cells are grown in a sequential batch reactor. The simplest macroscopic reaction scheme translating the data is first derived using a maximum likelihood principal component analysis. Subsequently, nonlinear least-squares estimation is used to determine the kinetic laws. The resulting dynamic model reproduces quite satisfactorily the experimental data, as evidenced in direct and cross-validation tests. Furthermore, model predictions can also be used to predict optimal medium renewal time and composition.

Validation of the revised Mystical Experience Questionnaire in experimental sessions with psilocybin.

Science.gov (United States)

Barrett, Frederick S; Johnson, Matthew W; Griffiths, Roland R

2015-11-01

The 30-item revised Mystical Experience Questionnaire (MEQ30) was previously developed within an online survey of mystical-type experiences occasioned by psilocybin-containing mushrooms. The rated experiences occurred on average eight years before completion of the questionnaire. The current paper validates the MEQ30 using data from experimental studies with controlled doses of psilocybin. Data were pooled and analyzed from five laboratory experiments in which participants (n=184) received a moderate to high oral dose of psilocybin (at least 20 mg/70 kg). Results of confirmatory factor analysis demonstrate the reliability and internal validity of the MEQ30. Structural equation models demonstrate the external and convergent validity of the MEQ30 by showing that latent variable scores on the MEQ30 positively predict persisting change in attitudes, behavior, and well-being attributed to experiences with psilocybin while controlling for the contribution of the participant-rated intensity of drug effects. These findings support the use of the MEQ30 as an efficient measure of individual mystical experiences. A method to score a "complete mystical experience" that was used in previous versions of the mystical experience questionnaire is validated in the MEQ30, and a stand-alone version of the MEQ30 is provided for use in future research. © The Author(s) 2015.

Learning Design of Problem Based Learning Model Based on Recommendations of Sintax Study and Contents Issues on Physics Impulse Materials with Experimental Activities

Directory of Open Access Journals (Sweden)

Kristia Agustina

2017-08-01

Full Text Available This study aims to design learning Problem Based Learning Model based on syntax study recommendations and content issues on Physics Impulse materials through experiments. This research is a development research with Kemp model. The reference for making the learning design is the result of the syntax study and the content of existing PBL implementation problems from Agustina research. This instructional design is applied to the physics material about Impulse done through experimental activity. Limited trials were conducted on the SWCU Physics Education Study Program students group Salatiga, while the validity test was conducted by high school teachers and physics education lecturers. The results of the trial evaluation are limited and the validity test is used to improve the designs that have been made. The conclusion of this research is the design of learning by using PBL model on Impuls material by referring the result of syntax study and the problem content of existing PBL implementation can be produced by learning activity designed in laboratory experiment activity. The actual problem for Impuls material can be used car crash test video at factory. The results of validation tests and limited trials conducted by researchers assessed that the design of learning made by researchers can be used with small revisions. Suggestions from this research are in making learning design by using PBL model to get actual problem can by collecting news that come from newspaper, YouTube, internet, and television.

Design, validation, and reliability of survey to measure female athlete triad knowledge among coaches

Directory of Open Access Journals (Sweden)

Jillian E. Frideres

2015-06-01

Full Text Available The purpose of this study was to design and to test the validity and reliability of an instrument to evaluate coaches' knowledge about the female athlete triad syndrome and their confidence in this knowledge. The instrument collects information regarding: knowledge of the syndrome, components, prevention and intervention; confidence of the coaches in their answers; and coach's characteristics (gender, degree held, years of experience in coaching females, continuing education participation specific to the syndrome and its components, and sport coached. The process of designing the questionnaire and testing the validity and reliability of it was done in four phases: a design and development of the instrument, b content validity, c instrument reliability, and d concurrent validity. The results show that the instrument is suitable for measuring coaches' female athlete triad knowledge. The instrument can contribute to assessing the coaches' knowledge level in relation to this topic.

Development and Validation of Stability-Indicating Method for Estimation of Chlorthalidone in Bulk and Tablets with the Use of Experimental Design in Forced Degradation Experiments

Directory of Open Access Journals (Sweden)

Sandeep Sonawane

2016-01-01

Full Text Available Chlorthalidone was subjected to various forced degradation conditions. Substantial degradation of chlorthalidone was obtained in acid, alkali, and oxidative conditions. Further full factorial experimental design was applied for acid and alkali forced degradation conditions, in which strength of acid/alkali, temperature, and time of heating were considered as independent variables (factors and % degradation was considered as dependent variable (response. Factors responsible for acid and alkali degradation were statistically evaluated using Yates analysis and Pareto chart. Furthermore, using surface response curve, optimized 10% degradation was obtained. All chromatographic separation was carried out on Phenomenex HyperClone C 18 column (250 × 4.6 mm, 5 μ, using mobile phase comprising methanol : acetonitrile : phosphate buffer (20 mM (pH 3.0 adjusted with o-phosphoric acid: 30 : 10 : 60% v/v. The flow rate was kept constant at 1 mL/min and eluent was detected at 241 nm. In calibration curve experiments, linearity was found to be in the range of 2–12 μg/mL. Validation experiments proved good accuracy and precision of the method. Also there was no interference of excipients and degradation products at the retention time of chlorthalidone, indicating specificity of the method.

A heat pump driven and hollow fiber membrane-based liquid desiccant air dehumidification system: Modeling and experimental validation

International Nuclear Information System (INIS)

Zhang, Li-Zhi; Zhang, Ning

2014-01-01

A compression heat pump driven and membrane-based liquid desiccant air dehumidification system is presented. The dehumidifier and the regenerator are made of two hollow fiber membrane bundles packed in two shells. Water vapor can permeate through these membranes effectively, while the liquid desiccant droplets are prevented from cross-over. Simultaneous heating and cooling of the salt solution are realized with a heat pump system to improve energy efficiency. In this research, the system is built up and a complete modeling is performed for the system. Heat and mass transfer processes in the membrane modules, as well as in the evaporator, the condenser, and other key components are modeled in detail. The whole model is validated by experiment. The performances of SDP (specific dehumidification power), dehumidification efficiency, EER (energy efficiency ratio) of heat pump, and the COP (coefficient of performance) of the system are investigated numerically and experimentally. The results show that the model can predict the system accurately. The dehumidification capabilities and the energy efficiencies of the system are high. Further, it performs well even under the harsh hot and humid South China weather conditions. - Highlights: • A membrane-based and heat pump driven air dehumidification system is proposed. • A real experimental set up is built and used to validate the model for the whole system. • Performance under design and varying operation conditions is investigated. • The system performs well even under harsh hot and humid conditions

The design, validation, and performance of Grace

Directory of Open Access Journals (Sweden)

Ru Zhu

2016-05-01

Full Text Available The design, validation and performance of Grace, a GPU-accelerated micromagnetic simulation software, are presented. The software adopts C+ + Accelerated Massive Parallelism (C+ + AMP so that it runs on GPUs from various hardware vendors including NVidia, AMD and Intel. At large simulation scales, up to two orders of magnitude of speedup factor is observed, compared to CPU-based micromagnetic simulation software OOMMF. The software can run on high-end professional GPUs as well as budget personal laptops, and is free to download.

Experimental validation of sound field control with a circular double-layer array of loudspeakers

DEFF Research Database (Denmark)

Chang, Jiho; Jacobsen, Finn

2013-01-01

This paper is concerned with experimental validation of a recently proposed method of controlling sound fields with a circular double-layer array of loudspeakers [Chang and Jacobsen, J. Acoust. Soc. Am. 131(6), 4518-4525 (2012)]. The double-layer of loudspeakers is realized with 20 pairs of closed...

Experimental investigation of shaping disturbance observer design for motion control of precision mechatronic stages with resonances

Science.gov (United States)

Yang, Jin; Hu, Chuxiong; Zhu, Yu; Wang, Ze; Zhang, Ming

2017-08-01

In this paper, shaping disturbance observer (SDOB) is investigated for precision mechatronic stages with middle-frequency zero/pole type resonance to achieve good motion control performance in practical manufacturing situations. Compared with traditional standard disturbance observer (DOB), in SDOB a pole-zero cancellation based shaping filter is cascaded to the mechatronic stage plant to meet the challenge of motion control performance deterioration caused by actual resonance. Noting that pole-zero cancellation is inevitably imperfect and the controller may even consequently become unstable in practice, frequency domain stability analysis is conducted to find out how each parameter of the shaping filter affects the control stability. Moreover, the robust design criterion of the shaping filter, and the design procedure of SDOB, are both proposed to guide the actual design and facilitate practical implementation. The SDOB with the proposed design criterion is applied to a linear motor driven stage and a voice motor driven stage, respectively. Experimental results consistently validate the effectiveness nature of the proposed SDOB scheme in practical mechatronics motion applications. The proposed SDOB design actually could be an effective unit in the controller design for motion stages of mechanical manufacture equipments.

Numerical Simulation and Experimental Validation of the Inflation Test of Latex Balloons

OpenAIRE

Bustos, Claudio; Herrera, Claudio García; Celentano, Diego; Chen, Daming; Cruchaga, Marcela

2016-01-01

Abstract Experiments and modeling aimed at assessing the mechanical response of latex balloons in the inflation test are presented. To this end, the hyperelastic Yeoh material model is firstly characterized via tensile test and, then, used to numerically simulate via finite elements the stress-strain evolution during the inflation test. The numerical pressure-displacement curves are validated with those obtained experimentally. Moreover, this analysis is extended to a biomedical problem of an...

Visualizing Experimental Designs for Balanced ANOVA Models using Lisp-Stat

Directory of Open Access Journals (Sweden)

Philip W. Iversen

2004-12-01

Full Text Available The structure, or Hasse, diagram described by Taylor and Hilton (1981, American Statistician provides a visual display of the relationships between factors for balanced complete experimental designs. Using the Hasse diagram, rules exist for determining the appropriate linear model, ANOVA table, expected means squares, and F-tests in the case of balanced designs. This procedure has been implemented in Lisp-Stat using a software representation of the experimental design. The user can interact with the Hasse diagram to add, change, or delete factors and see the effect on the proposed analysis. The system has potential uses in teaching and consulting.

Fundamentals of statistical experimental design and analysis

CERN Document Server

Easterling, Robert G

2015-01-01

Professionals in all areas - business; government; the physical, life, and social sciences; engineering; medicine, etc. - benefit from using statistical experimental design to better understand their worlds and then use that understanding to improve the products, processes, and programs they are responsible for. This book aims to provide the practitioners of tomorrow with a memorable, easy to read, engaging guide to statistics and experimental design. This book uses examples, drawn from a variety of established texts, and embeds them in a business or scientific context, seasoned with a dash of humor, to emphasize the issues and ideas that led to the experiment and the what-do-we-do-next? steps after the experiment. Graphical data displays are emphasized as means of discovery and communication and formulas are minimized, with a focus on interpreting the results that software produce. The role of subject-matter knowledge, and passion, is also illustrated. The examples do not require specialized knowledge, and t...

Bioinspiration: applying mechanical design to experimental biology.

Science.gov (United States)

Flammang, Brooke E; Porter, Marianne E

2011-07-01

The production of bioinspired and biomimetic constructs has fostered much collaboration between biologists and engineers, although the extent of biological accuracy employed in the designs produced has not always been a priority. Even the exact definitions of "bioinspired" and "biomimetic" differ among biologists, engineers, and industrial designers, leading to confusion regarding the level of integration and replication of biological principles and physiology. By any name, biologically-inspired mechanical constructs have become an increasingly important research tool in experimental biology, offering the opportunity to focus research by creating model organisms that can be easily manipulated to fill a desired parameter space of structural and functional repertoires. Innovative researchers with both biological and engineering backgrounds have found ways to use bioinspired models to explore the biomechanics of organisms from all kingdoms to answer a variety of different questions. Bringing together these biologists and engineers will hopefully result in an open discourse of techniques and fruitful collaborations for experimental and industrial endeavors.

Experimental validation of field cooling simulations for linear superconducting magnetic bearings

Energy Technology Data Exchange (ETDEWEB)

Dias, D H N; Motta, E S; Sotelo, G G; De Andrade Jr, R, E-mail: ddias@coe.ufrj.b [Laboratorio de aplicacao de Supercondutores (LASUP), Universidade Federal do Rio de Janeiro, Rio de Janeiro (Brazil)

2010-07-15

For practical stability of a superconducting magnetic bearing the refrigeration process must occur with the superconductor in the presence of the magnetic field (a field cooling (FC) process). This paper presents an experimental validation of a method for simulating this system in the FC case. Measured and simulated results for a vertical force between a high temperature superconductor and a permanent magnet rail are compared. The main purpose of this work is to consolidate a simulation tool that can help in future projects on superconducting magnetic bearings for MagLev vehicles.

Experimental design, modeling and optimization of polyplex formation between DNA oligonucleotides and branched polyethylenimine.

Science.gov (United States)

Clima, Lilia; Ursu, Elena L; Cojocaru, Corneliu; Rotaru, Alexandru; Barboiu, Mihail; Pinteala, Mariana

2015-09-28

The complexes formed by DNA and polycations have received great attention owing to their potential application in gene therapy. In this study, the binding efficiency between double-stranded oligonucleotides (dsDNA) and branched polyethylenimine (B-PEI) has been quantified by processing of the images captured from the gel electrophoresis assays. The central composite experimental design has been employed to investigate the effects of controllable factors on the binding efficiency. On the basis of experimental data and the response surface methodology, a multivariate regression model has been constructed and statistically validated. The model has enabled us to predict the binding efficiency depending on experimental factors, such as concentrations of dsDNA and B-PEI as well as the initial pH of solution. The optimization of the binding process has been performed using simplex and gradient methods. The optimal conditions determined for polyplex formation have yielded a maximal binding efficiency close to 100%. In order to reveal the mechanism of complex formation at the atomic-scale, a molecular dynamic simulation has been carried out. According to the computation results, B-PEI amine hydrogen atoms have interacted with oxygen atoms from dsDNA phosphate groups. These interactions have led to the formation of hydrogen bonds between macromolecules, stabilizing the polyplex structure.

Design and Validation of the Quantum Mechanics Conceptual Survey

Science.gov (United States)

McKagan, S. B.; Perkins, K. K.; Wieman, C. E.

2010-01-01

The Quantum Mechanics Conceptual Survey (QMCS) is a 12-question survey of students' conceptual understanding of quantum mechanics. It is intended to be used to measure the relative effectiveness of different instructional methods in modern physics courses. In this paper, we describe the design and validation of the survey, a process that included…

Development of a Conservative Model Validation Approach for Reliable Analysis

Science.gov (United States)

2015-01-01

CIE 2015 August 2-5, 2015, Boston, Massachusetts, USA [DRAFT] DETC2015-46982 DEVELOPMENT OF A CONSERVATIVE MODEL VALIDATION APPROACH FOR RELIABLE...obtain a conservative simulation model for reliable design even with limited experimental data. Very little research has taken into account the...3, the proposed conservative model validation is briefly compared to the conventional model validation approach. Section 4 describes how to account

Summary of the experimental multi-purpose very high temperature gas cooled reactor design

International Nuclear Information System (INIS)

1984-12-01

The report presents the design of Multi-purpose Very High Temperature Gas Cooled Reactor (the Experimental VHTR) based on the second stage of detailed design which was completed on March 1984, in the from of ''An application of reactor construction permit Appendix 8''. The Experimental VHTR is designed to satisfy with the design specification for the reactor thermal output 50 MW and reactor outlet temperature 950 0 C. The adequacy of the design is also checked by the safety analysis. The planning of plant system and safety is summarized such as safety design requirements and conformance with them, seismic design and plant arrangement. Concerning with the system of the Experimental VHTR the design basis, design data and components are described in the order. (author)

Design Issues and Inference in Experimental L2 Research

Science.gov (United States)

Hudson, Thom; Llosa, Lorena

2015-01-01

Explicit attention to research design issues is essential in experimental second language (L2) research. Too often, however, such careful attention is not paid. This article examines some of the issues surrounding experimental L2 research and its relationships to causal inferences. It discusses the place of research questions and hypotheses,…

Initial Validation of a Technical Writing Rubric for Engineering Design

Directory of Open Access Journals (Sweden)

Cheryl Bodnar

2018-02-01

Full Text Available Engineering design serves as the capstone experience of most undergraduate engineering programs. One of the key elements of the engineering design process is the compilation of results obtained into a technical report that can be shared and distributed to interested stakeholders including industry, faculty members and other relevant parties. In an effort to expand the tools available for assessment of engineering design technical reports, this study performed an initial validation of a previously developed Technical Writing rubric. The rubric was evaluated for its reliability to measure the intended construct, inter-rater reliability and external validity in comparison to an existing generalized written communication rubric. It was found that the rubric was reliable with Cronbach’s alpha for all dimensions between 0.817 and 0.976. The inter-rater reliability for the overall instrument was also found to be excellent at 0.85. Finally, it was observed that there were no statistically significant differences observed between the measurements obtained on the Technical Writing rubric in comparison to the more generalized Written Communication Value rubric. This demonstrates that although specific to engineering design environments the Technical Writing rubric was able to measure key constructs associated with written communication practice. This rubric can now serve as one additional tool for assessment of communication skills within engineering capstone design experiences.

Use of Experimental Design for Peuhl Cheese Process Optimization ...

African Journals Online (AJOL)

Use of Experimental Design for Peuhl Cheese Process Optimization. ... Journal of Applied Sciences and Environmental Management ... This work consisting in use of a central composite design enables the determination of optimal process conditions concerning: leaf extract volume added (7 mL), heating temperature ...

Experimentally supported control design for a direct drive robot

NARCIS (Netherlands)

Kostic, D.; Jager, de A.G.; Steinbuch, M.

2002-01-01

We promote the idea of an experimentally supported control design as a successful way to achieve accurate tracking of reference robot motions, under disturbance conditions and given the uncertainties arising from modeling errors. The Hinf robust control theory is used for design of motion

Theoretical model with experimental validation of a regenerative blower for hydrogen recirculation in a PEM fuel cell system

Energy Technology Data Exchange (ETDEWEB)

Badami, M.; Mura, M. [Dipartimento di Energetica, Politecnico di Torino, C.so Duca degli Abruzzi 24, Torino (Italy)

2010-03-15

A theoretical model of a regenerative blower used for the hydrogen recirculation of a Proton Exchange Membrane (PEM) fuel cell (FC) for automotive applications has been implemented and validated by means of experimental data. A momentum exchange theory was used to determine the head-flow rate curves, whereas the circulatory flow rate was determined through a theory based on the consideration of the centrifugal force field in the side channel and in the impeller vane grooves. The model allows a good forecast to be made of the blower behaviour, and only needs its main geometrical characteristics and some fluid-dynamic data as input. For this reason, the model could be very interesting, especially during the first sizing and the design activity of the blower. (author)

Experimental design and analysis for piezoelectric circular actuators in flow control applications

International Nuclear Information System (INIS)

Mane, Poorna; Mossi, Karla; Bryant, Robert

2008-01-01

Flow control can lead to saving millions of dollars in fuel costs each year by making an aircraft more efficient. Synthetic jets, a device for active flow control, operate by introducing small amounts of energy locally to achieve non-local changes in the flow field with large performance gains. These devices consist of a cavity with an oscillating diaphragm that divides it into active and passive sides. The active side has a small opening where a jet is formed, while the passive side does not directly participate in the fluidic jet. Over the years, research has shown that synthetic jet behavior is dependent on the active diaphragm and the cavity design; hence, the focus of this work. The performance of the synthetic jet is studied under various factors related to the diaphragm and the cavity geometry. Three diaphragms, manufactured from piezoelectric composites, were selected for this study: Bimorph, Thunder ® and Lipca. The overall factors considered are the driving signals, voltage, frequency, cavity height, orifice size, and passive cavity pressure. Using the average maximum jet velocity as the response variable, these factors are individually studied for each actuator, and statistical analysis tools are used to select the relevant factors in the response variable. The factors are divided into two experimental fractional factorial design matrices, with five and four factors, respectively. Both experiments are chosen to be of resolution V, where main factors are confounded with three-factor interactions. In the first experimental design, the results show that frequency is not a significant factor, while waveform is significant for all the actuators. In addition, the magnitude of the regression coefficients suggests that a model that includes the diaphragm as a factor may be possible. These results are valid within the ranges tested, that is low frequencies and sawtooth and sine waveform as driving signals. In the second experimental design, cavity dimensions are

Conceptual design of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1984-03-01

A conceptual design study (option C) has been carried out for the fusion experimental reactor (FER). In addition to design of the tokamak reactor and associated systems based on the reference design specifications, feasibility of a water-shield reactor concept was examined as a topical study. The design study for the reference tokamak reactor has produced a reactor concept for the FER, along with major R D items for the concept, based on close examinations on thermal design, electromagnetics, neutronics and remote maintenance. Particular efforts have been directed to the area of electromagnetics. Detailed analyses with close simulation models have been performed on PF coil arrangements and configurations, shell effects of the blanket for plasma position unstability, feedback control, and eddy currents during disruptions. The major design specifications are as follows; Peak fusion power 437 MW Major radius 5.5 m Minor radius 1.1 m Plasma elongation 1.5 Plasma current 5.3 MA Toroidal beta 4 % Field on axis 5.7 T (author)

Conceptual design of Fusion Experimental Reactor (FER)

International Nuclear Information System (INIS)

Tone, T.; Fujisawa, N.

1983-01-01

Conceptual design studies of the Fusion Experimental Reactor (FER) have been performed. The FER has an objective of achieving selfignition and demonstrating engineering feasibility as a next generation tokamak to JT-60. Various concepts of the FER have been considered. The reference design is based on a double-null divertor. Optional design studies with some attractive features based on advanced concepts such as pumped limiter and RF current drive have been carried out. Key design parameters are; fusion power of 440 MW, average neutron wall loading of 1MW/m 2 , major radius of 5.5m, plasma minor radius of 1.1m, plasma elongation of 1.5, plasma current of 5.3MA, toroidal beta of 4%, toroidal field on plasma axis of 5.7T and tritium breeding ratio of above unity

Numerical Simulation and Experimental Validation of the Inflation Test of Latex Balloons

Directory of Open Access Journals (Sweden)

Claudio Bustos

Full Text Available Abstract Experiments and modeling aimed at assessing the mechanical response of latex balloons in the inflation test are presented. To this end, the hyperelastic Yeoh material model is firstly characterized via tensile test and, then, used to numerically simulate via finite elements the stress-strain evolution during the inflation test. The numerical pressure-displacement curves are validated with those obtained experimentally. Moreover, this analysis is extended to a biomedical problem of an eyeball under glaucoma conditions.

Optimization of critical factors to enhance polyhydroxyalkanoates (PHA) synthesis by mixed culture using Taguchi design of experimental methodology.

Science.gov (United States)

Venkata Mohan, S; Venkateswar Reddy, M

2013-01-01

Optimizing different factors is crucial for enhancement of mixed culture bioplastics (polyhydroxyalkanoates (PHA)) production. Design of experimental (DOE) methodology using Taguchi orthogonal array (OA) was applied to evaluate the influence and specific function of eight important factors (iron, glucose concentration, VFA concentration, VFA composition, nitrogen concentration, phosphorous concentration, pH, and microenvironment) on the bioplastics production. Three levels of factor (2(1) × 3(7)) variation were considered with symbolic arrays of experimental matrix [L(18)-18 experimental trails]. All the factors were assigned with three levels except iron concentration (2(1)). Among all the factors, microenvironment influenced bioplastics production substantially (contributing 81%), followed by pH (11%) and glucose concentration (2.5%). Validation experiments were performed with the obtained optimum conditions which resulted in improved PHA production. Good substrate degradation (as COD) of 68% was registered during PHA production. Dehydrogenase and phosphatase enzymatic activities were monitored during process operation. Copyright © 2012 Elsevier Ltd. All rights reserved.

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .1. DESIGN CONSTRUCTION AND THEORETICAL EVALUATION

NARCIS (Netherlands)

DUINEVELD, CAA; SMILDE, AK; DOORNBOS, DA

The combination of process variables and mixture variables in experimental design is a problem which has not yet been solved. It is examined here whether a set of designs can be found which can be used for a series of models of reasonable complexity. The proposed designs are compared with known

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .1. DESIGN CONSTRUCTION AND THEORETICAL EVALUATION

NARCIS (Netherlands)

DUINEVELD, C. A. A.; Smilde, A. K.; Doornbos, D. A.

1993-01-01

The combination of process variables and mixture variables in experimental design is a problem which has not yet been solved. It is examined here whether a set of designs can be found which can be used for a series of models of reasonable complexity. The proposed designs are compared with known

An Experimental Verification of morphology of ibuprofen crystals from CAMD designed solvent

DEFF Research Database (Denmark)

Karunanithi, Arunprakash T.; Acquah, Charles; Achenie, Luke E.K.

2007-01-01

of crystals formed from solvents, necessitates additional experimental verification steps. In this work we report the experimental verification of crystal morphology for the case study, solvent design for ibuprofen crystallization, presented in Karunanithi et al. [2006. A computer-aided molecular design...

Development of knowledgebase system for assisting signal validation scheme design

International Nuclear Information System (INIS)

Kitamura, M.; Baba, T.; Washio, T.; Sugiyama, K.

1987-01-01

The purpose of this study is to develop a knowledgebase system to be used as a tool for designing signal validation schemes. The outputs from the signal validation scheme can be used as; (1) auxiliary signals for detecting sensor failures, (2) inputs to advanced instrumentation such as disturbance analysis and diagnosis system or safety parameter display system, and (3) inputs to digital control systems. Conventional signal validation techniques such as comparison of redundant sensors, limit checking, and calibration tests have been employed in nuclear power plants. However, these techniques have serious drawbacks, e.g. needs for extra sensors, vulnerability to common mode failures, limited applicability to continuous monitoring, etc. To alleviate these difficulties, a new signal validation technique has been developed by using the methods called analytic redundancy and parity space. Although the new technique has been proved feasible as far as preliminary tests are concerned, further developments should be made in order to enhance its practical applicability

Design and experimental characterization of an EM pump

International Nuclear Information System (INIS)

Kim, Hee Reyoung; Hong, Sang Hee

1999-01-01

Generally, an EM (electromagnetic) pump is been employed to circulate electrically conducting liquids by using the Lorentz force. Especially, at the liquid metal reactor (LMR), which uses liquid sodium with high electrical conductivity as a coolant, an EM pump is needed due to its advantages over a mechanical pump, such as no rotating parts, no noise, and simplicity. In this research, an EM pump of a pilot annular linear induction type with a flow rate of 200 l/min was designed by using the electrical equivalent-circuit method. The pump was designed and manufactured by considering material and environmental (high temperature and liquid sodium) requirements. The pump performance was experimentally characterized based on input currents, voltage, power, and frequency. Also, the theoretical prediction was compared with the experimental result

Experimental Design for Hanford Low-Activity Waste Glasses with High Waste Loading

International Nuclear Information System (INIS)

Piepel, Gregory F.; Cooley, Scott K.; Vienna, John D.; Crum, Jarrod V.

2015-01-01

This report discusses the development of an experimental design for the initial phase of the Hanford low-activity waste (LAW) enhanced glass study. This report is based on a manuscript written for an applied statistics journal. Appendices A, B, and E include additional information relevant to the LAW enhanced glass experimental design that is not included in the journal manuscript. The glass composition experimental region is defined by single-component constraints (SCCs), linear multiple-component constraints (MCCs), and a nonlinear MCC involving 15 LAW glass components. Traditional methods and software for designing constrained mixture experiments with SCCs and linear MCCs are not directly applicable because of the nonlinear MCC. A modification of existing methodology to account for the nonlinear MCC was developed and is described in this report. One of the glass components, SO 3 , has a solubility limit in glass that depends on the composition of the balance of the glass. A goal was to design the experiment so that SO 3 would not exceed its predicted solubility limit for any of the experimental glasses. The SO 3 solubility limit had previously been modeled by a partial quadratic mixture model expressed in the relative proportions of the 14 other components. The partial quadratic mixture model was used to construct a nonlinear MCC in terms of all 15 components. In addition, there were SCCs and linear MCCs. This report describes how a layered design was generated to (i) account for the SCCs, linear MCCs, and nonlinear MCC and (ii) meet the goals of the study. A layered design consists of points on an outer layer, and inner layer, and a center point. There were 18 outer-layer glasses chosen using optimal experimental design software to augment 147 existing glass compositions that were within the LAW glass composition experimental region. Then 13 inner-layer glasses were chosen with the software to augment the existing and outer-layer glasses. The experimental

Conceptual design of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1984-02-01

This report describes the engineering conceptual design of Fusion Experimental Reactor (FER) which is to be built as a next generation tokamak machine. This design covers overall reactor systems including MHD equilibrium analysis, mechanical configuration of reactor, divertor, pumped limiter, first wall/breeding blanket/shield, toroidal field magnet, poloidal field magnet, cryostat, electromagnetic analysis, vacuum system, power handling and conversion, NBI, RF heating device, tritium system, neutronics, maintenance, cooling system and layout of facilities. The engineering comparison of a divertor with pumped limiters and safety analysis of reactor systems are also conducted. (author)

Fast Bayesian optimal experimental design and its applications

KAUST Repository

Long, Quan

2015-01-01

We summarize our Laplace method and multilevel method of accelerating the computation of the expected information gain in a Bayesian Optimal Experimental Design (OED). Laplace method is a widely-used method to approximate an integration

Experimental investigation of stratified two-phase flows in the hot leg of a PWR for CFD validation

Energy Technology Data Exchange (ETDEWEB)

Vallee, Christophe; Lucas, Dirk [Helmholtz-Zentrum Dresden-Rossendorf (HZDR) e.V., Dresden (Germany). Inst. of Fluid Dynamics; Tomiyama, Akio [Kobe Univ (Japan). Graduate School of Engineering; Murase, Michio [Institute of Nuclear Safety System, Inc. (INSS), Fukui (Japan)

2012-12-15

Stratified 2-phase flows were investigated in 2 different models of the hot leg of a pressurised water reactor (PWR) in order to provide experimental data for the development and validation of computational fluid dynamics (CFD) codes. Therefore, the local flow structure was visualised with a high-speed video camera. Moreover, one test section was designed with a rectangular cross-section to achieve optimal observation conditions. The phenomenon of counter-current flow limitation (CCFL) was investigated, which may affect the reflux condenser cooling mode in some accident scenarios. The experiments were conducted with air and water at room temperature and maximum pressures of 3 bar as well as with steam and saturated water at boundary conditions of up to 50 bar and 264 C. The measured CCFL characteristics were compared with similar experimental data and correlations available in the literature. This shows that the channel height is the characteristic length to be used in the Wallis parameter for channels with rectangular cross-sections. Furthermore, the experimental results confirm that the Wallis similarity is appropriate to scale CCFL in the hot leg of a PWR over a wide range of pressure and temperature conditions. Finally, an image processing algorithm was developed to recognise the stratified interface in the camera frames. Subsequently, the interfacial structure along the hot leg was visualised by the representation of the probability distribution of the water level. (orig.)

Experimental Validation of Mathematical Framework for Fast Switching Valves used in Digital Hydraulic Machines

DEFF Research Database (Denmark)

Nørgård, Christian; Roemer, Daniel Beck; Bech, Michael Møller

2015-01-01

of 10 kW during switching (mean of approximately 250 W) and a pressure loss below 0.5 bar at 600 l/min. The main goal of this article is validate parts of the mathematical framework based on a series of experiments. Furthermore, this article aims to document the experience gained from the experimental...

Optimal Experimental Design of Furan Shock Tube Kinetic Experiments

KAUST Repository

Kim, Daesang

2015-01-07

A Bayesian optimal experimental design methodology has been developed and applied to refine the rate coefficients of elementary reactions in Furan combustion. Furans are considered as potential renewable fuels. We focus on the Arrhenius rates of Furan + OH ↔ Furyl-2 + H2O and Furan ↔ OH Furyl-3 + H2O, and rely on the OH consumption rate as experimental observable. A polynomial chaos surrogate is first constructed using an adaptive pseudo-spectral projection algorithm. The PC surrogate is then exploited in conjunction with a fast estimation of the expected information gain in order to determine the optimal design in the space of initial temperatures and OH concentrations.

Experimental design and quantitative analysis of microbial community multiomics.

Science.gov (United States)

Mallick, Himel; Ma, Siyuan; Franzosa, Eric A; Vatanen, Tommi; Morgan, Xochitl C; Huttenhower, Curtis

2017-11-30

Studies of the microbiome have become increasingly sophisticated, and multiple sequence-based, molecular methods as well as culture-based methods exist for population-scale microbiome profiles. To link the resulting host and microbial data types to human health, several experimental design considerations, data analysis challenges, and statistical epidemiological approaches must be addressed. Here, we survey current best practices for experimental design in microbiome molecular epidemiology, including technologies for generating, analyzing, and integrating microbiome multiomics data. We highlight studies that have identified molecular bioactives that influence human health, and we suggest steps for scaling translational microbiome research to high-throughput target discovery across large populations.

Thermomechanical simulations and experimental validation for high speed incremental forming

Science.gov (United States)

Ambrogio, Giuseppina; Gagliardi, Francesco; Filice, Luigino; Romero, Natalia

2016-10-01

Incremental sheet forming (ISF) consists in deforming only a small region of the workspace through a punch driven by a NC machine. The drawback of this process is its slowness. In this study, a high speed variant has been investigated from both numerical and experimental points of view. The aim has been the design of a FEM model able to perform the material behavior during the high speed process by defining a thermomechanical model. An experimental campaign has been performed by a CNC lathe with high speed to test process feasibility. The first results have shown how the material presents the same performance than in conventional speed ISF and, in some cases, better material behavior due to the temperature increment. An accurate numerical simulation has been performed to investigate the material behavior during the high speed process confirming substantially experimental evidence.

The Validity and Precision of the Comparative Interrupted Time-Series Design: Three Within-Study Comparisons

Science.gov (United States)

St. Clair, Travis; Hallberg, Kelly; Cook, Thomas D.

2016-01-01

We explore the conditions under which short, comparative interrupted time-series (CITS) designs represent valid alternatives to randomized experiments in educational evaluations. To do so, we conduct three within-study comparisons, each of which uses a unique data set to test the validity of the CITS design by comparing its causal estimates to…

International Thermonuclear Experimental Reactor

International Nuclear Information System (INIS)

Blevins, J.D.; Stasko, R.R.

1989-09-01

An international design team comprised of members from Canada, Europe, Japan, the Soviet Union, and the United States of America, are designing an experimental fusion test reactor. The engineering and testing objectives of this International Thermonuclear Experimental Reactor (ITER) are to validate the design and to demonstrate controlled ignition, extended burn of a deuterium and tritium plasma, and achieve steady state using technology expected to be available by 1990. The concept maximizes flexibility while allowing for a variety of plasma configurations and operating scenarios. During physics phase operation, the machine produces a 22 MA plasma current. In the technology phase, the machine can be reconfigured with a thicker shield and a breeding blanket to operate with an 18 MA plasma current at a major radius of 5.5 meters. Canada's involvement in the areas of safety, facility design, reactor configuration and maintenance builds on our internationally recognized design and operational expertise in developing tritium processes and CANDU related technologies

Validation process of simulation model

International Nuclear Information System (INIS)

San Isidro, M. J.

1998-01-01

It is presented a methodology on empirical validation about any detailed simulation model. This king of validation it is always related with an experimental case. The empirical validation has a residual sense, because the conclusions are based on comparisons between simulated outputs and experimental measurements. This methodology will guide us to detect the fails of the simulation model. Furthermore, it can be used a guide in the design of posterior experiments. Three steps can be well differentiated: Sensitivity analysis. It can be made with a DSA, differential sensitivity analysis, and with a MCSA, Monte-Carlo sensitivity analysis. Looking the optimal domains of the input parameters. It has been developed a procedure based on the Monte-Carlo methods and Cluster techniques, to find the optimal domains of these parameters. Residual analysis. This analysis has been made on the time domain and on the frequency domain, it has been used the correlation analysis and spectral analysis. As application of this methodology, it is presented the validation carried out on a thermal simulation model on buildings, Esp., studying the behavior of building components on a Test Cell of LECE of CIEMAT. (Author) 17 refs

Development of boiling transition analysis code TCAPE-INS/B based on mechanistic methods for BWR fuel bundles. Models and validations with boiling transition experimental data

International Nuclear Information System (INIS)

Ishida, Naoyuki; Utsuno, Hideaki; Kasahara, Fumio

2003-01-01

The Boiling Transition (BT) analysis code TCAPE-INS/B based on the mechanistic methods coupled with subchannel analysis has been developed for the evaluation of the integrity of Boiling Water Reactor (BWR) fuel rod bundles under abnormal operations. Objective of the development is the evaluation of the BT without using empirical BT and rewetting correlations needed for different bundle designs in the current analysis methods. TCAPE-INS/B consisted mainly of the drift-flux model, the film flow model, the cross-flow model, the thermal conductivity model and the heat transfer correlations. These models were validated systematically with the experimental data. The accuracy of the prediction for the steady-state Critical Heat Flux (CHF) and the transient temperature of the fuel rod surface after the occurrence of BT were evaluated on the validations. The calculations for the experiments with the single tube and bundles were carried out for the validations of the models incorporated in the code. The results showed that the steady-state CHF was predicted within about 6% average error. In the transient calculations, BT timing and temperature of the fuel rod surface gradient agreed well with experimental results, but rewetting was predicted lately. So, modeling of heat transfer phenomena during post-BT is under modification. (author)

Development and Validation of HPLC-DAD and UHPLC-DAD Methods for the Simultaneous Determination of Guanylhydrazone Derivatives Employing a Factorial Design.

Science.gov (United States)

Azevedo de Brito, Wanessa; Gomes Dantas, Monique; Andrade Nogueira, Fernando Henrique; Ferreira da Silva-Júnior, Edeildo; Xavier de Araújo-Júnior, João; Aquino, Thiago Mendonça de; Adélia Nogueira Ribeiro, Êurica; da Silva Solon, Lilian Grace; Soares Aragão, Cícero Flávio; Barreto Gomes, Ana Paula

2017-08-30

Guanylhydrazones are molecules with great pharmacological potential in various therapeutic areas, including antitumoral activity. Factorial design is an excellent tool in the optimization of a chromatographic method, because it is possible quickly change factors such as temperature, mobile phase composition, mobile phase pH, column length, among others to establish the optimal conditions of analysis. The aim of the present work was to develop and validate a HPLC and UHPLC methods for the simultaneous determination of guanylhydrazones with anticancer activity employing experimental design. Precise, exact, linear and robust HPLC and UHPLC methods were developed and validated for the simultaneous quantification of the guanylhydrazones LQM10, LQM14, and LQM17. The UHPLC method was more economic, with a four times less solvent consumption, and 20 times less injection volume, what allowed better column performance. Comparing the empirical approach employed in the HPLC method development to the DoE approach employed in the UHPLC method development, we can conclude that the factorial design made the method development faster, more practical and rational. This resulted in methods that can be employed in the analysis, evaluation and quality control of these new synthetic guanylhydrazones.

PSpice Modeling Platform for SiC Power MOSFET Modules with Extensive Experimental Validation

DEFF Research Database (Denmark)

Ceccarelli, Lorenzo; Iannuzzo, Francesco; Nawaz, Muhammad

2016-01-01

to simulate the performance of high current rating (above 100 A), multi-chip SiC MOSFET modules both for static and switching behavior. Therefore, the simulation results have been validated experimentally in a wide range of operating conditions, including high temperatures, gate resistance and stray elements....... The whole process has been repeated for three different modules with voltage rating of 1.2 kV and 1.7 kV, manufactured by three different companies. Lastly, a parallel connection of two modules of the same type has been performed in order to observe the unbalancing and mismatches experimentally......The aim of this work is to present a PSpice implementation for a well-established and compact physics-based SiC MOSFET model, including a fast, experimental-based parameter extraction procedure in a MATLAB GUI environment. The model, originally meant for single-die devices, has been used...

The influence of the design matrix on treatment effect estimates in the quantitative analyses of single-subject experimental design research.

Science.gov (United States)

Moeyaert, Mariola; Ugille, Maaike; Ferron, John M; Beretvas, S Natasha; Van den Noortgate, Wim

2014-09-01

The quantitative methods for analyzing single-subject experimental data have expanded during the last decade, including the use of regression models to statistically analyze the data, but still a lot of questions remain. One question is how to specify predictors in a regression model to account for the specifics of the design and estimate the effect size of interest. These quantitative effect sizes are used in retrospective analyses and allow synthesis of single-subject experimental study results which is informative for evidence-based decision making, research and theory building, and policy discussions. We discuss different design matrices that can be used for the most common single-subject experimental designs (SSEDs), namely, the multiple-baseline designs, reversal designs, and alternating treatment designs, and provide empirical illustrations. The purpose of this article is to guide single-subject experimental data analysts interested in analyzing and meta-analyzing SSED data. © The Author(s) 2014.

Experimental validation of decay heat calculation codes and associated nuclear data libraries for fusion energy

International Nuclear Information System (INIS)

Maekawa, Fujio; Wada, Masayuki; Ikeda, Yujiro

2001-01-01

Validity of decay heat calculations for safety designs of fusion reactors was investigated by using decay heat experimental data on thirty-two fusion reactor relevant materials obtained at the 14-MeV neutron source facility of FNS in JAERI. Calculation codes developed in Japan, ACT4 and CINAC version 4, and nuclear data bases such as JENDL/Act-96, FENDL/A-2.0 and Lib90 were used for the calculation. Although several corrections in algorithms for both the calculation codes were needed, it was shown by comparing calculated results with the experimental data that most of activation cross sections and decay data were adequate. In cases of type 316 stainless steel and copper which were important for ITER, prediction accuracy of decay heat within ±10% was confirmed. However, it was pointed out that there were some problems in parts of data such as improper activation cross sections, e,g., the 92 Mo(n, 2n) 91g Mo reaction in FENDL, and lack of activation cross section data, e.g., the 138 Ba(n, 2n) 137m Ba reaction in JENDL. Modifications of cross section data were recommended for 19 reactions in JENDL and FENDL. It was also pointed out that X-ray and conversion electron energies should be included in decay data. (author)

Experimental validation of decay heat calculation codes and associated nuclear data libraries for fusion energy

Energy Technology Data Exchange (ETDEWEB)

Maekawa, Fujio; Wada, Masayuki; Ikeda, Yujiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2001-01-01

Validity of decay heat calculations for safety designs of fusion reactors was investigated by using decay heat experimental data on thirty-two fusion reactor relevant materials obtained at the 14-MeV neutron source facility of FNS in JAERI. Calculation codes developed in Japan, ACT4 and CINAC version 4, and nuclear data bases such as JENDL/Act-96, FENDL/A-2.0 and Lib90 were used for the calculation. Although several corrections in algorithms for both the calculation codes were needed, it was shown by comparing calculated results with the experimental data that most of activation cross sections and decay data were adequate. In cases of type 316 stainless steel and copper which were important for ITER, prediction accuracy of decay heat within {+-}10% was confirmed. However, it was pointed out that there were some problems in parts of data such as improper activation cross sections, e,g., the {sup 92}Mo(n, 2n){sup 91g}Mo reaction in FENDL, and lack of activation cross section data, e.g., the {sup 138}Ba(n, 2n){sup 137m}Ba reaction in JENDL. Modifications of cross section data were recommended for 19 reactions in JENDL and FENDL. It was also pointed out that X-ray and conversion electron energies should be included in decay data. (author)

Thermal enhancement cartridge heater modified tritium hydride bed development, Part 2 - Experimental validation of key conceptual design features

Energy Technology Data Exchange (ETDEWEB)

Heroux, K.J.; Morgan, G.A. [Savannah River Laboratory, Aiken, SC (United States)

2015-03-15

The Thermal Enhancement Cartridge Heater Modified (TECH Mod) tritium hydride bed is an interim replacement for the first generation (Gen1) process hydride beds currently in service in the Savannah River Site (SRS) Tritium Facilities. 3 new features are implemented in the TECH Mod hydride bed prototype: internal electric cartridge heaters, porous divider plates, and copper foam discs. These modifications will enhance bed performance and reduce costs by improving bed activation and installation processes, in-bed accountability measurements, end-of-life bed removal, and He-3 recovery. A full-scale hydride bed test station was constructed at the Savannah River National Laboratory (SRNL) in order to evaluate the performance of the prototype TECH Mod hydride bed. Controlled hydrogen (H{sub 2}) absorption/ desorption experiments were conducted to validate that the conceptual design changes have no adverse effects on the gas transfer kinetics or H{sub 2} storage/release properties compared to those of the Gen1 bed. Inert gas expansions before, during, and after H{sub 2} flow tests were used to monitor changes in gas transfer rates with repeated hydriding/de-hydriding of the hydride material. The gas flow rates significantly decreased after initial hydriding of the material; however, minimal changes were observed after repeated cycling. The data presented herein confirm that the TECH Mod hydride bed would be a suitable replacement for the Gen1 bed with the added enhancements expected from the advanced design features. (authors)

Intuitive web-based experimental design for high-throughput biomedical data.

Science.gov (United States)

Friedrich, Andreas; Kenar, Erhan; Kohlbacher, Oliver; Nahnsen, Sven

2015-01-01

Big data bioinformatics aims at drawing biological conclusions from huge and complex biological datasets. Added value from the analysis of big data, however, is only possible if the data is accompanied by accurate metadata annotation. Particularly in high-throughput experiments intelligent approaches are needed to keep track of the experimental design, including the conditions that are studied as well as information that might be interesting for failure analysis or further experiments in the future. In addition to the management of this information, means for an integrated design and interfaces for structured data annotation are urgently needed by researchers. Here, we propose a factor-based experimental design approach that enables scientists to easily create large-scale experiments with the help of a web-based system. We present a novel implementation of a web-based interface allowing the collection of arbitrary metadata. To exchange and edit information we provide a spreadsheet-based, humanly readable format. Subsequently, sample sheets with identifiers and metainformation for data generation facilities can be created. Data files created after measurement of the samples can be uploaded to a datastore, where they are automatically linked to the previously created experimental design model.

Achieving external validity in home advantage research: generalizing crowd noise effects.

Science.gov (United States)

Myers, Tony D

2014-01-01

Different factors have been postulated to explain the home advantage phenomenon in sport. One plausible explanation investigated has been the influence of a partisan home crowd on sports officials' decisions. Different types of studies have tested the crowd influence hypothesis including purposefully designed experiments. However, while experimental studies investigating crowd influences have high levels of internal validity, they suffer from a lack of external validity; decision-making in a laboratory setting bearing little resemblance to decision-making in live sports settings. This focused review initially considers threats to external validity in applied and theoretical experimental research. Discussing how such threats can be addressed using representative design by focusing on a recently published study that arguably provides the first experimental evidence of the impact of live crowd noise on officials in sport. The findings of this controlled experiment conducted in a real tournament setting offer a level of confirmation of the findings of laboratory studies in the area. Finally directions for future research and the future conduct of crowd noise studies are discussed.

Optimization design study of an innovative divertor concept for future experimental tokamak-type fusion reactors

International Nuclear Information System (INIS)

Willem Janssens, Ir.; Crutzen, Y.; Farfaletti-Casali, F.; Matera, R.

1991-01-01

The design optimization study of an innovative divertor concept for future experimental tokamak-type fusion devices is both an answer to the actual problems encountered in the multilayer divertor proposals and an illustration of a rational modelling philosophy and optimization strategy for the development of a new divertor structure. Instead of using mechanical attachment or metallurgical bonding of the protective material to the heat sink as in most actual divertor concepts, the so-called brush divertor in this study uses an array of unidirectional fibers penetrating in both the protective armor and the underling composite heat sink. Although the approach is fully concentrated on the divertor performance, including both a description of its function from the theoretical point of view and an overview of the problems related to the materials choice and evaluation, both the approach followed in the numerical modelling and the judgment of the results are thought to be valid also for other applications. Therefore the spin-off of the study must be situated in both the technological progress towards a feasible divertor solution, which introduces no additional physical uncertainties, and in the general area of the thermo-mechanical finite-element modelling on both macro-and microscale. The brush divertor itself embodies the use, and thus the modelling, of advanced materials such as tailor-made metal matrix composites and dispersion strengthened metals, and is shown to offer large potential advantages, demanding however and experimental validation under working conditions. It is clearly indicated where the need originates for an integrated experimental program which must allow to verify the basic modelling assumptions in order to arrive at the use of numerical computation as a powerful and realistic tool of structural testing and life-time prediction

Experimental burn plot trial in the Kruger National Park: history, experimental design and suggestions for data analysis

Directory of Open Access Journals (Sweden)

R. Biggs

2003-12-01

Full Text Available The experimental burn plot (EBP trial initiated in 1954 is one of few ongoing long-termfire ecology research projects in Africa. The trial aims to assess the impacts of differentfire regimes in the Kruger National Park. Recent studies on the EBPs have raised questions as to the experimental design of the trial, and the appropriate model specificationwhen analysing data. Archival documentation reveals that the original design was modified on several occasions, related to changes in the park's fire policy. These modifications include the addition of extra plots, subdivision of plots and changes in treatmentsover time, and have resulted in a design which is only partially randomised. The representativity of the trial plots has been questioned on account of their relatively small size,the concentration of herbivores on especially the frequently burnt plots, and soil variation between plots. It is suggested that these factors be included as covariates inexplanatory models or that certain plots be excluded from data analysis based on resultsof independent studies of these factors. Suggestions are provided for the specificationof the experimental design when analysing data using Analysis of Variance. It is concluded that there is no practical alternative to treating the trial as a fully randomisedcomplete block design.

Design study of the experimental multi-purpose high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Tsunoda, Ryokichi

1981-01-01

In this paper, the design study carried out since 1973 is outlined. The basic conceptual design was performed in fiscal 1973. In this design, concept was established on the total system of the experimental high temperature gas-cooled reactor including heat-utilizing system. The first conceptual design was carried out in fiscal 1974. The range of design was limited to the experimental reactor and its direct heat-removing system. The part 2 of the first conceptual design was performed in fiscal 1975, and the system design concerning the plant characteristics was made. The part 1 of the adjustment design was carried out in fiscal 1976, and the subject was the adjustment design of plant systems. The part 2 was performed in fiscal 1977, and the characteristics of plant control system were analyzed. In fiscal 1978, the analysis of flow characteristics in the core was made. The integrated system design was carried out in fiscal 1979, and the design of the total plant system except heat-utilizing system was started again. The part 1 of the detailed design was performed in fiscal 1980, and in addition, the possibility of increasing power output was examined. The construction cost of the experimental reactor plant estimated in 1979 was far higher than that in 1973. (Kako, I.)

Design validation of the ITER EC upper launcher according to codes and standards

Energy Technology Data Exchange (ETDEWEB)

Spaeh, Peter, E-mail: peter.spaeh@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); Aiello, Gaetano [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); Gagliardi, Mario [Karlsruhe Institute of Technology, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); F4E, Fusion for Energy, Joint Undertaking, Barcelona (Spain); Grossetti, Giovanni; Meier, Andreas; Scherer, Theo; Schreck, Sabine; Strauss, Dirk; Vaccaro, Alessandro [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); Weinhorst, Bastian [Karlsruhe Institute of Technology, Institute for Neutron Physics and Reactor Technology, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany)

2015-10-15

Highlights: • A set of applicable codes and standards has been chosen for the ITER EC upper launcher. • For a particular component load combinations, failure modes and stress categorizations have been determined. • The design validation was performed in accordance with the “design by analysis”-approach of the ASME boiler and pressure vessel code section III. - Abstract: The ITER electron cyclotron (EC) upper launcher has passed the CDR (conceptual design review) in 2005 and the PDR (preliminary design review) in 2009 and is in its final design phase now. The final design will be elaborated by the European consortium ECHUL-CA with contributions from several research institutes in Germany, Italy, the Netherlands and Switzerland. Within this consortium KIT is responsible for the design of the structural components (the upper port plug, UPP) and also the design integration of the launcher. As the selection of applicable codes and standards was under discussion for the past decade, the conceptual and the preliminary design of the launcher structure were not elaborated in straight accordance with a particular code but with a variety of well-acknowledged engineering practices. For the final design it is compulsory to validate the design with respect to a typical engineering code in order to be compliant with the ITER quality and nuclear requirements and to get acceptance from the French regulator. This paper presents typical design validation of the closure plate, which is the vacuum and Tritium barrier and thus a safety relevant component of the upper port plug (UPP), performed with the ASME boiler and pressure vessel code. Rationales for choosing this code are given as well as a comparison between different design methods, like the “design by rule” and the “design by analysis” approach. Also the selections of proper load specifications and the identification of potential failure modes are covered. In addition to that stress categorizations, analyses

Design validation of the ITER EC upper launcher according to codes and standards

International Nuclear Information System (INIS)

Spaeh, Peter; Aiello, Gaetano; Gagliardi, Mario; Grossetti, Giovanni; Meier, Andreas; Scherer, Theo; Schreck, Sabine; Strauss, Dirk; Vaccaro, Alessandro; Weinhorst, Bastian

2015-01-01

Highlights: • A set of applicable codes and standards has been chosen for the ITER EC upper launcher. • For a particular component load combinations, failure modes and stress categorizations have been determined. • The design validation was performed in accordance with the “design by analysis”-approach of the ASME boiler and pressure vessel code section III. - Abstract: The ITER electron cyclotron (EC) upper launcher has passed the CDR (conceptual design review) in 2005 and the PDR (preliminary design review) in 2009 and is in its final design phase now. The final design will be elaborated by the European consortium ECHUL-CA with contributions from several research institutes in Germany, Italy, the Netherlands and Switzerland. Within this consortium KIT is responsible for the design of the structural components (the upper port plug, UPP) and also the design integration of the launcher. As the selection of applicable codes and standards was under discussion for the past decade, the conceptual and the preliminary design of the launcher structure were not elaborated in straight accordance with a particular code but with a variety of well-acknowledged engineering practices. For the final design it is compulsory to validate the design with respect to a typical engineering code in order to be compliant with the ITER quality and nuclear requirements and to get acceptance from the French regulator. This paper presents typical design validation of the closure plate, which is the vacuum and Tritium barrier and thus a safety relevant component of the upper port plug (UPP), performed with the ASME boiler and pressure vessel code. Rationales for choosing this code are given as well as a comparison between different design methods, like the “design by rule” and the “design by analysis” approach. Also the selections of proper load specifications and the identification of potential failure modes are covered. In addition to that stress categorizations, analyses

The experimental Balzac program at Masurca in support of the design of Super Phenix 2

International Nuclear Information System (INIS)

Sztark, H.; d'Angelo, A.; Soule, R.; Granget, G.

1986-09-01

The Balzac experimental program, performed in the Masurca critical assembly at Cadarache since 1985, is designed for the validation of the neutron physics requirements related to the physical options of the SPX2 project. Geometrically simple configurations are chosen in which parameters, typical for those physical options, are varied in a systematic manner while the basic fissile composition is kept the same. Measurements will be made especially of the critical mass, the distributions of reaction rates, spectral indices, 10 B(n,α) reaction and gamma-ray heating in particular in the control-rod and in internal storage regions. Reactivity effects of (UPu)O 2 isotopic composition variations and of different control-rod absorber configurations will be also measured using the MSM technique

Vivaldi: Visualization and validation of biomacromolecular NMR structures from the PDB

Science.gov (United States)

Hendrickx, Pieter M S; Gutmanas, Aleksandras; Kleywegt, Gerard J

2013-01-01

We describe Vivaldi (VIsualization and VALidation DIsplay; http://pdbe.org/vivaldi), a web-based service for the analysis, visualization, and validation of NMR structures in the Protein Data Bank (PDB). Vivaldi provides access to model coordinates and several types of experimental NMR data using interactive visualization tools, augmented with structural annotations and model-validation information. The service presents information about the modeled NMR ensemble, validation of experimental chemical shifts, residual dipolar couplings, distance and dihedral angle constraints, as well as validation scores based on empirical knowledge and databases. Vivaldi was designed for both expert NMR spectroscopists and casual non-expert users who wish to obtain a better grasp of the information content and quality of NMR structures in the public archive. © Proteins 2013. © 2012 Wiley Periodicals, Inc. PMID:23180575

Simulation and Experimental Studies on Grain Selection and Structure Design of the Spiral Selector for Casting Single Crystal Ni-Based Superalloy.