Optical enhancement of phosphor-converted wLEDs using glass beads

Science.gov (United States)

Güner, Tuğrul; Şentürk, Ufuk; Demir, Mustafa M.

2017-10-01

YAG:Ce3+ is a yellow-source compound commonly used in phosphor conversion layers for direct coating or remote phosphor configurations in LED illumination. This material, however, suffers from a high correlated color temperature, and low color-rendering index due to its deficiency in the red spectrum. In this study, glass beads (GB) with an average particle diameter of 10 μm were introduced to the conversion layer of a YAG:Ce3+ particulate-filled polydimethylsiloxane matrix composite structure and found to improve the optical features of the resulting composite.

Imaging camera system of OYGBR-phosphor-based white LED lighting

Science.gov (United States)

Kobashi, Katsuya; Taguchi, Tsunemasa

2005-03-01

The near-ultraviolet (nUV) white LED approach is analogous to three-color fluorescent lamp technology, which is based on the conversion of nUV radiation to visible light via the photoluminescence process in phosphor materials. The nUV light is not included in the white light generation from nUV-based white LED devices. This technology can thus provide a higher quality of white light than the blue and YAG method. A typical device demonstrates white luminescence with Tc=3,700 K, Ra > 93, K > 40 lm/W and chromaticity (x, y) = (0.39, 0.39), respectively. The orange, yellow, green and blue OYGB) or orange, yellow, red, green and blue (OYRGB) device shows a luminescence spectrum broader than of an RGB white LED and a better color rendering index. Such superior luminous characteristics could be useful for the application of several kinds of endoscope. We have shown the excellent pictures of digestive organs in a stomach of a dog due to the strong green component and high Ra.

High color rendering index of remote-type white LEDs with multi-layered quantum dot-phosphor films and short-wavelength pass dichroic filters

Science.gov (United States)

Yoon, Hee Chang; Oh, Ji Hye; Do, Young Rag

2014-09-01

This paper introduces high color rendering index (CRI) white light-emitting diodes (W-LEDs) coated with red emitting (Sr,Ca)AlSiN3:Eu phosphors and yellowish-green emitting AgIn5S8/ZnS (AIS/ZS) quantum dots (QDs) on glass or a short-wavelength pass dichroic filter (SPDF), which transmit blue wavelength regions and reflect yellow wavelength regions. The red emitting (Sr,Ca)AlSiN3:Eu phosphor film is coated on glass and a SPDF using a screen printing method, and then the yellowish-green emitting AIS/ZS QDs are coated on the red phosphor (Sr,Ca)AlSiN3:Eu film-coated glass and SPDF using the electrospray (e-spray) method.To fabricate the red phosphor film, the optimum amount of phosphor is dispersed in a silicon binder to form a red phosphor paste. The AIS/ZS QDs are mixed with dimethylformamide (DMF), toluene, and poly(methyl methacrylate) (PMMA) for the e-spray coating. The substrates are spin-coated with poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) to fabricate a conductive surface. The CRI of the white LEDs is improved through inserting the red phosphor film between the QD layer and the glass substrate. Furthermore, the light intensities of the multi-layered phosphor films are enhanced through changing the glass substrate to the SPDF. The correlated color temperatures (CCTs) vary as a function of the phosphor concentration in the phosphor paste. The optical properties of the yellowish-green AIS/ZS QDs and red (Sr,Ca)AlSiN3:Eu phosphors are characterized using photoluminescence (PL), and the multi-layered QD-phosphor films are measured using electroluminescence (EL) with an InGaN blue LED (λmax = 450 nm) at 60 mA.

Luminescent features of sol–gel derived rare-earth multi-doped oxyfluoride nano-structured phosphors for white LED application

International Nuclear Information System (INIS)

Gouveia-Neto, A.S.; Silva, A.F. da; Bueno, L.A.; Costa, E.B. da

2012-01-01

Rare-earth doped oxyfluoride 75SiO 2 :25PbF 2 nano-structured phosphors for white-light-emitting diodes were synthesized by thermal treatment of precursor sol–gel derived glasses. Room temperature luminescence features of Eu 3+ , Sm 3+ , Tb 3+ , Eu 3+ /Tb 3+ , and Sm 3+ /Tb 3+ ions incorporated into low-phonon-energy PbF 2 nanocrystals dispersed in the aluminosilicate glass matrix and excited with UV light emitting diode were investigated. The luminescence spectra exhibited strong emission signals in the red (600, 610, 625, and 646 nm), green (548 and 560 nm), and blue (485 nm) wavelength regions. White-light emission was observed in Sm/Tb and Eu/Tb double-doped activated phosphors employing UV-LED excitation at 395 nm. The dependence of the luminescence emission intensities upon annealing temperature and rare-earth concentration was also examined. The results indicated that there exist optimum annealing temperature and activator ion concentration in order to obtain intense visible emission light with high color rendering index. The study suggests that the nanocomposite phosphor based upon 75SiO 2 :25PbF 2 host herein reported is a promising contender for white-light LED applications. - Highlights: ► White-light emission in double-doped activated phosphors employing UV-LED excitation. ► Luminescent features of europium, samarium, and terbium in nanocrystals dispersed in aluminosilicate glass. ► New nanocomposite phosphor host for white-light LED applications.

White light-emitting diodes (LEDs) using (oxy)nitride phosphors

International Nuclear Information System (INIS)

Xie, R-J; Hirosaki, N; Sakuma, K; Kimura, N

2008-01-01

(Oxy)nitride phosphors have attracted great attention recently because they are promising luminescent materials for phosphor-converted white light-emitting diodes (LEDs). This paper reports the luminescent properties of (oxy)nitride phosphors in the system of M-Si-Al-O-N (M = Li, Ca or Sr), and optical properties of white LEDs using a GaN-based blue LED and (oxy)nitride phosphors. The phosphors show high conversion efficiency of blue light, suitable emission colours and small thermal quenching. The bichromatic white LEDs exhibit high luminous efficacy (∼55 lm W -1 ) and the multi-phosphor converted white LEDs show high colour rendering index (Ra 82-95). The results indicate that (oxy)nitride phosphors demonstrate their superior suitability to use as down-conversion luminescent materials in white LEDs

Host sensitized novel red phosphor CaZrSi{sub 2}O{sub 7} : Eu{sup 3+} for near UV and blue LED-based white LEDs

Energy Technology Data Exchange (ETDEWEB)

Bandi, Vengala Rao; Jeong, Junho; Jang, Kiwan; Lee, Ho Sueb [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Jayasimhadri, M [Department of Applied Physics, Delhi Technological University, Delhi (India); Yi, Soung-Soo [Department of Photonics, Silla University, Busan (Korea, Republic of); Jeong, Jung-Hyun, E-mail: kwjang@changwon.ac.k [Department of Physics, Pukyong National University, Busan (Korea, Republic of)

2010-10-06

A series of red phosphors Ca{sub 1-x}ZrSi{sub 2}O{sub 7} : Eu{sub x} (x = 0.5,1,5,10,12 mol%) were prepared by a solid-state reaction technique at various temperatures and their structural and optical properties were investigated. The x-ray diffraction profiles showed that all peaks could be attributed to the monoclinic phase CaZrSi{sub 2}O{sub 7} doped with Eu{sup 3+}. SEM, FTIR, TG and DTA profiles have also been characterized to explore their structural properties. The luminescence properties of these resulting phosphors have been characterized by photoluminescence spectra. The host matrix itself has shown a strong blue emission which has its maximum intensity at 470 nm. The excitation spectra of CaZrSi{sub 2}O{sub 7} : Eu{sup 3+} revealed two excitation bands at 395 and 464 nm which correspond to the sharp {sup 7}F{sub 0}-{sup 5}L{sub 6} and {sup 7}F{sub 0}-{sup 5}D{sub 2} transitions of Eu{sup 3+} and matches well with the two popular emissions from n-UV/blue GaN-based LEDs. The prominent red emission was obtained at 615 nm by the excitation transitions {sup 5}L{sub 6}, {sup 5}D{sub 2} of Eu{sup 3+} through the non-radiative energy transfer process from the host to the Eu{sup 3+} ion. The effects of charge compensation by monovalent ions on the luminescence behaviour of a red emitting phosphor CaZrSi{sub 2}O{sub 7} : Eu{sup 3+} were investigated. The high colour saturation and the low thermal quenching effect of these phosphors make it a potential red component for white light emitting diodes (w-LEDs).

Red light emitting solid state hybrid quantum dot-near-UV GaN LED devices

International Nuclear Information System (INIS)

Song, Hongjoo; Lee, Seonghoon

2007-01-01

We produced core-shell (CdSe)ZnSe quantum dots by direct colloidal chemical synthesis and the surface-passivation method-an overcoating of the core CdSe with a larger-bandgap material ZnSe. The (CdSe)ZnSe quantum dots(QDs) play the role of a colour conversion centre. We call these quantum dots nanophosphors. We fabricated red light emitting hybrid devices of (CdSe)ZnSe QDs and a near-UV GaN LED by combining red light emitting (CdSe)ZnSe quantum dots (as a colour conversion centre) with a near-UV(NUV) GaN LED chip (as an excitation source). A few good red phosphors have been known for UV excitation wavelengths, and red phosphors for UV excitation have been sought for a long time. Here we tested the possibility of using (CdSe)ZnSe QDs as red nanophosphors for UV excitation. The fabricated red light emitting hybrid device of (CdSe)ZnSe and a NUV GaN LED chip showed a good luminance. We demonstrated that the (CdSe)ZnSe quantum dots were promising red nanophosphors for NUV excitation and that a red LED made of QDs and a NUV excitation source was a highly efficient hybrid device

Synthesis of novel Dy3+ activated phosphate phosphors for NUV excited LED

International Nuclear Information System (INIS)

Shinde, K.N.; Dhoble, S.J.; Kumar, Animesh

2011-01-01

The new trivalent dysprosium activated X 6 AlP 5 O 20 (where X=Sr, Ba, Ca and Mg) phosphors were prepared by the combustion method. The prepared phosphors are characterized by XRD, photoluminescence and SEM techniques. Excited by 350 nm near-ultraviolet (NUV) light, the phosphors show an efficient blue and yellow band emissions, which originates from the 4 F 9/2 → 6 H 15/2 and 4 F 9/2 → 6 H 13/2 transitions of Dy 3+ ion, respectively. The excitation spectra of the phosphors are broadband extending from 340 to 400 nm, which are characteristics of NUV excited LED. The effect of the Dy 3+ concentration on the luminescence properties of X 6 AlP 5 O 20 :Dy 3+ (where X=Sr, Ba, Ca and Mg) phosphors is studied. Ca 6 AlP 5 O 20 phosphors show strong PL emission intensity around 25 times more as compared to Ba 6 AlP 5 O 20 , Sr 6 AlP 5 O 20 and Mg 6 AlP 5 O 20 phosphors. The investigated prepared phosphors are suitable for a NUV excited LED. - Research highlights: → Novel Dy 3+ activated X 6 AlP 5 O 20 (where X=Sr,Ba,Ca and Mg) phosphors were prepared by combustion method which is very low cost and time saving synthesis method. → The excitation spectra of the phosphors are broad band extending from 340 nm to 400 nm, which is characteristics of NUV excited LED. → PL emission spectra show two emissions (485 and 573 nm) and X 6 AlP 5 O 20 :Dy 3+ 0.5 mol% (where X=Sr,Ba,Ca and Mg) phosphors shows strongest PL emission intensity. → SEM analysis indicates that phosphor particles have irregular shape, porous morphology and less than 3-4 μm in size, which is suitable for the solid state lighting (coating purpose).

Considerable photoluminescence enhancement of LiEu(MoO4)2 red phosphors via Bi and/or Si doping for white LEDs

International Nuclear Information System (INIS)

Wang, Qing-Feng; Liu, Ying; Wang, Yu; Wang, Wenxi; Wan, Yi; Wang, Gui-Gen; Lu, Zhou-Guang

2015-01-01

Graphical abstract: Doping of Bi and Si into the lattice leads to an considerable increase of the excitation efficiency and luminous intensity, and obvious movement of the CIE chromaticity coordinates to the NTSC standard values of the LiEu(MoO 4 ) 2 , a promising red phosphors suitable for near UV excited white-light emitting diodes. - Highlights: • High performance red phosphors for near UV light excited white LEDs. • Lithium lanthanide molybdate red phosphors. • Bi and Si substitution. • Considerable enhancement of luminescence intensity and excitation efficiency. • CIE chromaticity coordinates very close to the NTSC standard values. - Abstract: Novel Bi and/or Si substituted LiEu(MoO 4 ) 2 phosphors, where Bi was used as sensitizer to enhance the emission intensity and Si was used as substitution to improve the excitation efficiency, were prepared using the sol–gel method, and the photoluminescent properties of the resulting phosphors were intensively investigated. All samples can be excited efficiently by UV (395 nm) light and emit bright red light at 614 nm, which are coupled well with the characteristic emission from a UV-LED. In the Bi 3+ -doped samples, the intensities of the main emission line ( 5 D 0 – 7 F 2 transition at 614 nm) are strengthened because of the energy transition from Bi 3+ to Eu 3+ . With the substitution of Mo 4+ by Si 4+ , there are no significant changes in the emission peak positions, but the emission intensity was significantly enhanced under 395 nm excitation. Particularly, the LiEu 0.9 Bi 0.1 (Mo 0.97 Si 0.03 O 4 ) 2 phosphor doped with both Bi and Si demonstrates superior comprehensive photoluminescence properties with an excellent combination of easy excitation in the near UV range, bright emission intensity, high PL quantum efficiency as well as suitable decay time, which are very suitable for application as red phosphor for near UV type LEDs

A novel greenish yellow-orange red Ba3Y4O9:Bi(3+),Eu(3+) phosphor with efficient energy transfer for UV-LEDs.

Science.gov (United States)

Li, Kai; Lian, Hongzhou; Shang, Mengmeng; Lin, Jun

2015-12-21

A series of novel color-tunable Ba3Y4O9:Bi(3+),Eu(3+) phosphors were prepared for the first time via the high-temperature solid-state reaction route. The effect of Bi(3+) concentration on the emission intensity of Ba3Y4O9:Bi(3+) was investigated. The emission spectra of the Ba3Y4O9:Bi(3+),Eu(3+) phosphors present both a greenish yellow band of Bi(3+) emission centered at 523 nm, and many characteristic emission lines of Eu(3+), derived from the allowed (3)P1-(1)S0 transition of the Bi(3+) ion and the (5)D0-(7)FJ transition of the Eu(3+) ion, respectively. The energy transfer phenomenon from Bi(3+) to Eu(3+) ions is observed under UV excitation in Bi(3+), Eu(3+) co-doped Ba3Y4O9 phosphors, and their transfer mechanism is demonstrated to be a resonant type via dipole-quadrupole interaction. The critical distance between Bi(3+) and Eu(3+) for the energy transfer effect was calculated via the concentration quenching and spectral overlap methods. Results show that color tuning from greenish yellow to orange red can be realized by adjusting the mole ratio of Bi(3+) and Eu(3+) concentrations based on the principle of energy transfer. Moreover, temperature-dependent PL properties, CIE chromaticity coordinates and quantum yields of Ba3Y4O9:Bi(3+),Eu(3+) phosphors were also supplied. It is illustrated that the as-prepared Ba3Y4O9:Bi(3+),Eu(3+) phosphors can be potential candidates for color-tunable phosphors applied in UV-pumped LEDs.

Effects of Graphene Monolayer Coating on the Optical Performance of Remote Phosphors

NARCIS (Netherlands)

Yazdan Mehr, M.; Vollebregt, S.; van Driel, W.D.; Zhang, G.Q.

2017-01-01

A graphene monolayer has been successfully coated on one side of a bisphenol-A-polycarbonate (BPA-PC) plate, used as a substrate for remote phosphor applications in light-emitting diode (LED)-based products. Using a photoresist transferring method, graphene sheet has been coated on BPA-PC plates.

Photoluminescence studies of organic phosphor coated diffusing surface using blue inorganic light-emitting diode as excitation source

International Nuclear Information System (INIS)

Singh, Gyanendra; Mehta, Dalip Singh

2013-01-01

We report the studies on photoluminescence (PL) of organic phosphor coated on a diffusing surface using a blue inorganic light-emitting diode (LED) array as an excitation source. The organic phosphor composite coated diffuser was used to scatter the directional blue light from the LED array. Some of the blue light is absorbed by the organic phosphor composite and the phosphor molecules are excited and re-emit light at longer wavelengths due to the PL process. The output light consists of scattered blue light plus phosphor generated broadband yellow light, thus making white light. The diffuser was made up of a plastic substrate coated with an organic composite of small molecule fluorescent material zinc(II)bis(8-hydroxyquinoline) (Znq 2 ) doped with different percentages of electro-phosphorescent metal complex iridium(III)bis(2-methyldibenzo-[f, h] quinoxaline) (acetylacetonate) ([Ir(MDQ) 2 (acac)]). By means of changing the concentration and the thickness of the phosphor composite material the colour coordinates of white light were achieved. The CIE coordinates and correlated colour temperature were calculated for various thicknesses and phosphor composite concentrations and the results are reported. (paper)

Zero- and two-dimensional hybrid carbon phosphors for high colorimetric purity white light-emission.

Science.gov (United States)

Ding, Yamei; Chang, Qing; Xiu, Fei; Chen, Yingying; Liu, Zhengdong; Ban, Chaoyi; Cheng, Shuai; Liu, Juqing; Huang, Wei

2018-03-01

Carbon nanomaterials are promising phosphors for white light emission. A facile single-step synthesis method has been developed to prepare zero- and two-dimensional hybrid carbon phosphors for the first time. Zero-dimensional carbon dots (C-dots) emit bright blue luminescence under 365 nm UV light and two-dimensional nanoplates improve the dispersity and film forming ability of C-dots. As a proof-of-concept application, the as-prepared hybrid carbon phosphors emit bright white luminescence in the solid state, and the phosphor-coated blue LEDs exhibit high colorimetric purity white light-emission with a color coordinate of (0.3308, 0.3312), potentially enabling the successful application of white emitting phosphors in the LED field.

Color stable phosphors for LED lamps and methods for preparing them

Science.gov (United States)

Murphy, James Edward; Setlur, Anant Achyut; Camardello, Samuel Joseph

2013-11-26

An LED lamp includes a light source configured to emit radiation with a peak intensity at a wavelength between about 250 nm and about 550 nm; and a phosphor composition configured to be radiationally coupled to the light source. The phosphor composition includes particles of a phosphor of formula I, said particles having a coating composition disposed on surfaces thereof; ((Sr.sub.1-zM.sub.z).sub.1-(x+w)A.sub.wCe.sub.x).sub.3(Al.sub.1-ySi.sub.y-)O.sub.4+y+3(x-w)F.sub.1-y-3(x-w) I wherein the coating composition comprises a material selected from aluminum oxide, magnesium oxide, calcium oxide, barium oxide, strontium oxide, zinc oxide, aluminum hydroxide, magnesium hydroxide, calcium hydroxide, barium hydroxide, strontium hydroxide, zinc hydroxide, aluminum phosphate, magnesium phosphate, calcium phosphate, barium phosphate, strontium phosphate, and combinations thereof; and A is Li, NA, K, or Rb, or a combination thereof; M is Ca, Ba, Mg, Zn, or a combination thereof; and 0

Synthesis and luminescence properties of glass ceramics containing MSiO3:Eu2+ (M=Ca, Sr, Ba) phosphors for white LED

International Nuclear Information System (INIS)

Cui Zhiguang; Jia Guohua; Deng Degang; Hua Youjie; Zhao Shilong; Huang Lihui; Wang Huanping; Ma Hongping; Xu Shiqing

2012-01-01

Eu 2+ doped silicate glasses were prepared of the system 52SiO 2 -48MO: xEu 2+ (in molar ratio, M=Ca, Sr, Ba; x=1, 3, 5, 7, 9) by a high temperature melt-quenching method in a reducing atmosphere. Glass ceramics containing MSiO 3 :Eu 2+ (M=Ca, Sr, Ba) nano-phosphors were obtained after the heat treatment of the glass samples. The excitation, emission spectra and lifetime decay curves of 4f 6 5d 1 →4f 7 of Eu 2+ were measured and interpreted with respect to their crystal structures and multi-site occupations of divalent europium in the hosts. Their excitation bands mainly extend from 450 to 250 nm, which is adaptable to the main emission region of the UV LED chip. With UV light excitation, the Eu 2+ emission in CaSiO 3 , SrSiO 3 and BaSiO 3 shows blue, green and yellow colors centered at 440, 505 and 555 nm, respectively. The critical Eu 2+ concentration was studied and determined to be x=5 for both CaSiO 3 and SrSiO 3 and x=7 for BaSiO 3 phosphors. The results show that the Eu 2+ doped glass ceramic phosphors containing MSiO 3 (M=Ca, Sr, Ba) nano-crystals can be used as potential matrix materials for a high power white LED pumped by the UV LED chip. - Highlights: → Glass ceramic containing MSiO 3 :Eu 2+ (M=Ca, Sr, Ba) phosphors prepared. → Derived phosphors emit intensively blue, green and yellow colors. → Their luminescence properties and crystal structures have been investigated. → Concentration quenching effects observed and analyzed. → Potential application for UV chip exciting white LED evaluated.

Considerable photoluminescence enhancement of LiEu(MoO{sub 4}){sub 2} red phosphors via Bi and/or Si doping for white LEDs

Energy Technology Data Exchange (ETDEWEB)

Wang, Qing-Feng [Department of Materials Science and Engineering, Harbin Institute of Technology Shenzhen Graduate School, Shenzhen, Guangdong 518055 (China); Department of Materials Science and Engineering, South University of Science and Technology of China, Shenzhen, Guangdong 518055 (China); Liu, Ying [Department of Materials Science and Engineering, South University of Science and Technology of China, Shenzhen, Guangdong 518055 (China); Wang, Yu [Department of Physics and Materials Science, City University of Hong Kong, Hong Kong Special Administrative Region (Hong Kong); Wang, Wenxi; Wan, Yi [Department of Materials Science and Engineering, South University of Science and Technology of China, Shenzhen, Guangdong 518055 (China); Wang, Gui-Gen [Department of Materials Science and Engineering, Harbin Institute of Technology Shenzhen Graduate School, Shenzhen, Guangdong 518055 (China); Lu, Zhou-Guang [Department of Materials Science and Engineering, South University of Science and Technology of China, Shenzhen, Guangdong 518055 (China)

2015-03-15

Graphical abstract: Doping of Bi and Si into the lattice leads to an considerable increase of the excitation efficiency and luminous intensity, and obvious movement of the CIE chromaticity coordinates to the NTSC standard values of the LiEu(MoO{sub 4}){sub 2}, a promising red phosphors suitable for near UV excited white-light emitting diodes. - Highlights: • High performance red phosphors for near UV light excited white LEDs. • Lithium lanthanide molybdate red phosphors. • Bi and Si substitution. • Considerable enhancement of luminescence intensity and excitation efficiency. • CIE chromaticity coordinates very close to the NTSC standard values. - Abstract: Novel Bi and/or Si substituted LiEu(MoO{sub 4}){sub 2} phosphors, where Bi was used as sensitizer to enhance the emission intensity and Si was used as substitution to improve the excitation efficiency, were prepared using the sol–gel method, and the photoluminescent properties of the resulting phosphors were intensively investigated. All samples can be excited efficiently by UV (395 nm) light and emit bright red light at 614 nm, which are coupled well with the characteristic emission from a UV-LED. In the Bi{sup 3+}-doped samples, the intensities of the main emission line ({sup 5}D{sub 0}–{sup 7}F{sub 2} transition at 614 nm) are strengthened because of the energy transition from Bi{sup 3+} to Eu{sup 3+}. With the substitution of Mo{sup 4+} by Si{sup 4+}, there are no significant changes in the emission peak positions, but the emission intensity was significantly enhanced under 395 nm excitation. Particularly, the LiEu{sub 0.9}Bi{sub 0.1}(Mo{sub 0.97}Si{sub 0.03}O{sub 4}){sub 2} phosphor doped with both Bi and Si demonstrates superior comprehensive photoluminescence properties with an excellent combination of easy excitation in the near UV range, bright emission intensity, high PL quantum efficiency as well as suitable decay time, which are very suitable for application as red phosphor for near UV

Studies in crystal structure and luminescence properties of Eu3+-doped metal tungstate phosphors for white LEDs

International Nuclear Information System (INIS)

Lee, Gwan-Hyoung; Kang, Shinhoo

2011-01-01

The correlation between the crystal structure and luminescent properties of Eu 3+ -doped metal tungstate phosphors for white LEDs was investigated. Red-emitting A 4-3x (WO 4 ) 2 :Eu x 3+ (A=Li, Na, K) and B (4-3x)/2 (WO 4 ) 2 :Eu x 3+ (B=Mg, Ca, Sr) phosphors were synthesized by solid-state reactions. The findings confirmed that these phosphors exhibited a strong absorption in the near UV to green range, due to the intra-configurational 4f-4f electron transition of Eu 3+ ions. The high doping concentration of Eu 3+ enhanced the absorption of near UV light and red emission without any detectable concentration quenching. Based on the results of a Rietveld refinement, it was attributed to the unique crystal structure. In the crystal structure of the Eu 3+ -doped metal tungstate phosphor, the critical energy transfer distance is larger than 5 A so that exchange interactions between Eu 3+ ions would occur with difficulty, even at a high doping concentration. The energy transfer between Eu 3+ ions, which causes a decrease in red emission with increasing concentration of Eu 3+ , appears to be due to electric multi-polar interactions. In addition, the Eu-O distance in the host lattice affected the shape of emission spectrum by splitting of emission peak at the 5 D 0 → 7 F 2 transition of Eu 3+ . - Highlights: → Eu 3+ -doped metal tungstate was synthesized as a red phosphor for white LEDs. → Crystal structure is tetragonal with a space group of I4 1 /c. → A strong absorption in the near UV to green range was observed. → High doping of Eu 3+ enhanced the absorption of near UV light and red emission.

UV absorption coefficients of Y2(1-x-y)Gd2xEu2yO3 phosphors

International Nuclear Information System (INIS)

Ling, M.; Yocom, P.W.; Soules, T.F.

1990-01-01

The ability of a phosphor to absorb 254 nm excitation is important in the development of phosphors for fluorescent lamps. Recently the optical properties of phosphor coating were modeled using ray tracing Monte-Carlo techniques. These calculations provided a relationship between absorptance measured on a semi-infinite plaque at a given wavelength and the product of the absorption coefficient of the phosphor and its particle diameter. The purpose of this work is to provide experimental data for comparison with the calculated data, to demonstrate a technique for obtaining absorption coefficients and to provide UV absorption coefficients obtained in this way for important yttrium oxide europium red-emitting phosphors

Synthesis and optical properties of red/blue-emitting Sr2MgSi2O7:Eu3+/Eu2+ phosphors for white LED

Directory of Open Access Journals (Sweden)

Tong Thi Hao Tam

2016-06-01

Full Text Available Phosphor-converted white light emitting diodes (white LEDs have received great attention in recent years since they have several excellent features such as high lumen output, low power consumption, long lifetime and environmentally friendly. In this work, we report the co-precipitation synthesis of red/blue Sr2MgSi2O7:Eu3+/Eu2+ phosphors with various Eu doping concentration. The results show that the obtained Sr2MgSi2O7:Eu3+/Eu2+ phosphors have good crystallinity and emit strong red (Sr2MgSi2O7:Eu3+ and blue (Sr2MgSi2O7:Eu2+ emissions under near UV light excitation. The sharp emission peaks at 577, 590, 612, 653, and 701 nm corresponded to the typical 5D0 → 7Fj (j = 0,1,2,3,4 transitions of Eu3+, and the blue emission peaking at 460 nm is attributed to the typical 4f65d1-4f7 transition of Eu2+ in the same Sr2MgSi2O7 host lattice. Both phosphors can be well excited in the wavelength range of 260–400 nm where the near UV-LED is well matched. The above results suggest that the Sr2MgSi2O7:Eu3+/Eu2+ phosphors are promising red/blue-emitting phosphors for the application in near UV pumped phosphor-converted white LEDs.

Effects of Graphene Monolayer Coating on the Optical Performance of Remote Phosphors

Science.gov (United States)

Yazdan Mehr, M.; Volgbert, S.; van Driel, W. D.; Zhang, G. Q.

2017-10-01

A graphene monolayer has been successfully coated on one side of a bisphenol-A-polycarbonate (BPA-PC) plate, used as a substrate for remote phosphor applications in light-emitting diode (LED)-based products. Using a photoresist transferring method, graphene sheet has been coated on BPA-PC plates. The results show that this graphene monolayer significantly improves the lifetime and performance of LEDs mainly by protecting them against external degradation factors such as moisture and oxygen. Also, LED-based products composed of graphene-coated BPA-PC plates exhibit longer stability with comparatively less loss of luminous efficiency. This method has great potential to significantly improve the reliability of not only LED-based products but also many other microelectronics packaging and components, in which moisture and oxygen are the key causes of failures.

Photocatalytic effects for the TiO2-coated phosphor materials

International Nuclear Information System (INIS)

Yoon, Jin-Ho; Jung, Sang-Chul; Kim, Jung-Sik

2011-01-01

Research highlights: → The photocatalytic behavior of the coupling of TiO 2 with phosphorescent materials. → The photobleaching of an MB aqueous solution under visible light irradiation. → The ALD TiO 2 -coated phosphor composite showed much higher photocatalytic reactivity. → The light emitted from the phosphors contributed to the photo-generation. - Abstract: This study investigated the photocatalytic behavior of the coupling of TiO 2 with phosphorescent materials. A TiO 2 thin film was deposited on CaAl 2 O 4 :Eu 2+ ,Nd 3+ phosphor particles by using atomic layer deposition (ALD), and its photocatalytic reaction was investigated by the photobleaching of an aqueous solution of methylene-blue (MB) under visible light irradiation. To clarify the mechanism of the TiO 2 -phosphorescent materials, two different samples of TiO 2 -coated phosphor and TiO 2 -Al 2 O 3 -coated phosphor particles were prepared. The photocatalytic mechanisms of the ALD TiO 2 -coated phosphor powders were different from those of the pure TiO 2 and TiO 2 -Al 2 O 3 -coated phosphor. The absorbance in a solution of the ALD TiO 2 -coated phosphor decreased much faster than that of pure TiO 2 under visible irradiation. In addition, the ALD TiO 2 -coated phosphor showed moderately higher photocatalytic degradation of MB solution than the TiO 2 -Al 2 O 3 -coated phosphor did. The TiO 2 -coated phosphorescent materials were characterized by transmission electron microscopy (TEM), Auger electron spectroscopy (AES) and X-ray photon spectroscopy (XPS).

High colour purity single-phased full colour emitting white LED phosphor Sr2V2O7:Eu3+

International Nuclear Information System (INIS)

Zhou Zhi; Zhou Nan; He Zhangxing; Liu Suqin; Liu Younian; Tian Ziwei; Wang Nanfang; Mao Zhiyong; Hintzen, H T

2013-01-01

Single-phased white-light-emitting phosphor Sr 2 V 2 O 7 :Eu 3+ was successfully synthesized by the solid-state method. The result of x-ray diffraction analysis indicated that the obtained phosphor has the same crystal structure as that of Sr 2 V 2 O 7 . The synthesized Sr 2 V 2 O 7 :Eu 3+ was combined with near-UV light (365 nm) chips and then assembled into ligtht-emitting diodes (LED) devices, which generated white light with colour coordinates of (0.324, 0.317). The white light was generated from yellow-green and red emissions, which should be attributed to the host Sr 2 V 2 O 7 and dopant Eu ions, respectively. The effects of the concentration of Eu ions and charge compensation on the emission intensity were carefully investigated. The results show that the energy migrates from the host to the dopant and also that Li 2 CO 3 should be the best charge compensator for this single-phased phosphor. In addition, the colour rendering index and luminescence efficiency of the fabricated LED devices with Sr 1.90 V 2 O 7 :0.10Eu 3+ phosphor were 91 and 32 lm W -1 , respectively, suggesting that Sr 1.90 V 2 O 7 :0.10Eu 3+ phosphor is a potential candidate for the phosphor-converted white-light-emitting diodes with near-UV chips.

Using rare earth doped thiosilicate phosphors in white light emitting LEDs: Towards low colour temperature and high colour rendering

International Nuclear Information System (INIS)

Smet, P.F.; Korthout, K.; Haecke, J.E. van; Poelman, D.

2008-01-01

Rare earth doped thiosilicates are promising materials for use in phosphor converted light emitting diodes (pcLEDs). These phosphors (including the hosts Ca 2 SiS 4 , BaSi 2 S 5 and Ba 2 SiS 4 in combination with Ce 3+ and/or Eu 2+ doping) cover the entire visible part of the spectrum, as the emission colour can be changed from deep blue to red. The photoluminescence emission spectrum and the overlap of the excitation spectrum with the emission of pumping LEDs is evaluated. The trade-off between high colour rendering and high electrical-to-optical power efficiency is discussed by simulation with both blue and UV emitting LEDs. Finally, a phosphor combination with low colour temperature (3000 K) and high colour rendering (CRI = 93) is proposed

High efficiency nitride based phosphores for white LEDs

NARCIS (Netherlands)

Li, Yuan Qiang; Hintzen, H.T.J.M.

2008-01-01

In this overview paper, novel rare-earth doped silicon nitride based phosphors for white LEDs applications have been demonstrated. The luminescence properties of orange-red-emitting phosphors (M2Si5N8:Eu2+) and green-to-yellow emitting phosphors (MSi2N2O2:Eu2+, M = Ca, Sr, Ba) are discussed in

Waterborne UV coating for industrial applications

International Nuclear Information System (INIS)

Bhattacharya, I.N.

2007-01-01

(Full Text): Solvent borne industrial coatings are being replaced by environment friendly coatings like Ultra Violet (UV) or Electron Beam (Eb) cured coatings, Powder coatings and Waterborne coatings. Waterborne systems enjoy the biggest share from this shift. UV and EB coatings provide the advantages of instant cure at room temperature, high scratch and abrasion resistance combined with excellent chemical resistance. Polyurethane (PU) chemistry is the dominant chemistry in Industrial coatings as they provide a very high level of performance. Most PU coatings are solvent based 2-component systems comprising of a resin and a cross linker. Polyurethane dispersions (PUD) in water in single pack are available but mainly addresses the Do It Yourself (DIY) market because of their slow drying speeds. Performance of PUD in most cases is inferior to solvent borne 2-component PU systems.Therefore the combination of PU dispersion and UV/EB curable technology has led to new innovative waterborne polymers called UV curable polyurethane dispersions (UVPUD). UVPUD are zero VOC systems as they are coalescent free. They are higher in molecular weight than standard UV curable products resulting in lower shrinkage coatings and provide good adhesion to substrates. Their low-viscosity makes them suitable for application by spray, curtain coater and even roller coater, without having to use monomers. UVPUD display superior chemical and mechanical properties necessary to protect high quality surface from the challenging usage conditions. UVPUD resins are therefore tailor-made to address performance needs like excellence in outdoor durability, scratch resistance, stain resistance, adhesion etc. UVPUD technology is now growing rapidly in industrial coatings for applications such as resilient flooring, wooden parquet flooring, automotive interior plastics, mobile phones etc. (Author)

Structure dependent luminescence characterization of green-yellow emitting Sr{sub 2}SiO{sub 4}:Eu{sup 2+} phosphors for near UV LEDs

Energy Technology Data Exchange (ETDEWEB)

Han, J.K. [University of California, San Diego, Materials Science and Engineering Program, La Jolla, CA 92093 (United States); Hannah, M.E.; Piquette, A. [Central Research, OSRAM SYLVANIA, 71 Cherry Hill Drive Beverly, MA 01915 (United States); Hirata, G.A. [Centro de Nanociencias y Nanotecnolgia, Universidad Nacional Autonoma de Mexico, Km. 107 Carretera Tijuana-Ensenada Apdo, Ensenada, MX CP 22860 (Mexico); Talbot, J.B. [University of California, San Diego, Materials Science and Engineering Program, La Jolla, CA 92093 (United States); Mishra, K.C. [Central Research, OSRAM SYLVANIA, 71 Cherry Hill Drive Beverly, MA 01915 (United States); McKittrick, J., E-mail: jmckittrick@ucsd.edu [University of California, San Diego, Materials Science and Engineering Program, La Jolla, CA 92093 (United States)

2012-01-15

This paper reports on the luminescence properties of mixtures of {alpha}- and {beta}-(Sr{sub 0.97}Eu{sub 0.03}){sub 2}SiO{sub 4} phosphors. These phosphors were prepared by 3 different synthesis techniques: a modified sol-gel/Pechini method, a co-precipitation method and a combustion method. The structural and optical properties of these phosphors were compared to those of solid state synthesized powders. The emission spectra consist of a weak broad blue band centered near 460 nm and a strong broad green-yellow band centered between 543 and 573 nm depending on the crystal structure. The green-yellow emission peak blue-shifts as the amount of {beta} phase increases and the photoluminescence emission intensity and quantum efficiency of the mixed phase powders is greater than those of predominant {alpha}-phase powders when excited between 370 and 410 nm. Thus, (Sr{sub 1-x}Eu{sub x}){sub 2}SiO{sub 4} with larger proportion of the {beta} phase are more promising candidates than single {alpha}-phase powders for use as a green-yellow emitting phosphor for near UV LED applications. Finally the phosphors prepared by the sol-gel/Pechini method, which have larger amount of {beta} phase, have a higher emission intensity and quantum efficiency than those prepared by co-precipitation or combustion synthesis. - Highlights: > Mixtures of {alpha}- and {beta}-Sr{sub 2}SiO{sub 4}:Eu{sup 2+} phosphors were prepared by 3 different synthesis methods. > Emission peak blue-shifts as the amount of {beta} phase increases. > Emission intensity and QE of the {alpha}+{beta} powders are greater than those of single {alpha} phase. > Phosphors prepared by sol-gel/Pechini have the highest emission intensity and QE.

LED deep UV source for charge management of gravitational reference sensors

International Nuclear Information System (INIS)

Sun Kexun; Allard, Brett; Buchman, Saps; Williams, Scott; Byer, Robert L

2006-01-01

Proof mass electrical charge management is an important functionality for the ST-7-LTP technology demonstration flight and for LISA. Photoemission for charge control is accomplished by using deep ultraviolet (UV) light to excite photoelectron emission from an Au alloy. The conventional UV source is a mercury vapour lamp. We propose and demonstrate charge management using a deep UV light emitting diode (LED) source. We have acquired selected AlGaN UV LEDs, characterized their performance and successfully used them to realize charge management. The UV LEDs emit at a 257 nm central wavelength with a bandwidth of ∼12 nm. The UV power for a free-space LED is ∼120 μW, and after fibre coupling is ∼16 μW, more than sufficient for LISA applications. We have directly observed the LED UV light-induced photocurrent response from an Au photocathode and an Au-coated GRS/ST-7 proof mass. We demonstrated fast switching of UV LEDs and associated fast changes in photocurrent. This allows modulation and continuous discharge to meet stringent LISA disturbance reduction requirements. We propose and demonstrate AC charge management outside the gravitational wave signal band. Further, the megahertz bandwidth for UV LED switching allows for up to six orders of magnitude dynamic power range and a number of novel modes of operations. The UV LED based charge management system offers the advantages of small-size, lightweight, fibre-coupled operation with very low power consumption

Color-tunable and luminescence properties of phosphors of Ce{sup 3+} and Tb{sup 3+} co-doped La{sub 5}Si{sub 3}O{sub 12}N for UV w-LEDs

Energy Technology Data Exchange (ETDEWEB)

Deng, Junru; Chen, Jian; Liu, Yangai, E-mail: liuyang@cugb.edu.cn

2016-02-15

A series of Ce{sup 3+}, Tb{sup 3+} and Ce{sup 3+}/Tb{sup 3+} co-doped in La{sub 5}Si{sub 3}O{sub 12}N phosphors were synthesized by conventional high temperature solid state reaction method. With the increase of Tb{sup 3+}, the green emission was realized in (La{sub 0.94−y}Ce{sub 0.06}Tb{sub y}){sub 5}Si{sub 3}O{sub 12}N phosphors on the basis of the efficient energy transfer from Ce{sup 3+} to Tb{sup 3+} with an efficiency (η{sub T}) over 58.72%. The room temperature PL decay curves of the Ce{sup 3+} ions in (La{sub 0.94−y}Ce{sub 0.06}Tb{sub y}){sub 5}Si{sub 3}O{sub 12}N phosphors monitored at 460 nm with an excitation at 365 nm indicated that the energy transfer process between Ce{sup 3+} and Tb{sup 3+} indeed took place. The CIE chromaticity diagrams for (La{sub 0.94−y}Ce{sub 0.06}Tb{sub y}){sub 5}Si{sub 3}O{sub 12}N phosphors were also observed, which shows the color tuned from blue to blue-greenish to green with the increase of Tb{sup 3+} concentration from 0.01 to 0.08. These results demonstrated that Tb{sup 3+} ion with low 4f–4f absorption efficiency in near UV region can play the role of an activator in narrow green-emitting phosphor through efficient energy feeding by allowing 4f–5d absorption of Ce{sup 3+} with high oscillator strength. All the results indicated that the Ce{sup 3+} and Tb{sup 3+} activated La{sub 5}Si{sub 3}O{sub 12}N phosphor may be good candidates for blue-green components in n-UV white LEDs. - Highlights: • A series of Ce{sup 3+}, Tb{sup 3+} and Ce{sup 3+}/Tb{sup 3+} co-doped in La{sub 5}Si{sub 3}O{sub 12}N phosphors were synthesized by high temperature solid state reaction method. • The green emission was realized in (La{sub 0.94−y}Ce{sub 0.06}Tb{sub y})Si{sub 3}O{sub 12}N phosphors on the basis of the highly efficient energy transfer. • The Ce{sup 3+} and Tb{sup 3+} activated La{sub 5}Si{sub 3}O{sub 12}N phosphor may be good candidates for blue-green components in n-UV white LEDs.

Preparation and Characterization of UV Emitting Fluoride Phosphors for Phototherapy Lamps

Science.gov (United States)

Belsare, P. D.; Moharil, S. V.; Joshi, C. P.; Omanwar, S. K.

2011-10-01

The use of ultraviolet radiation for the treatment of various skin diseases is well known for long time. Phototherapy employs ultraviolet-blue radiation to cure skin diseases. The basis of phototherapy is believed to be the direct interaction of light of certain frequencies with tissue to cause a change in immune response. Currently dermatologists use UV lamps having specific emissions in UV region for treating various skin diseases. The treatment of skin diseases using artificial sources of UV radiation is now well established and more than 50 types of skin diseases are treated by phototherapy. This is an effective treatment for many skin disorders, such as psoriasis, vitiligo, ofujis disease, morphea , scleroderma, cutaneous T-cell lymphoma, lupus erythematosus, hyperbilirubinemia commonly known as infant jaundice, acne vulgaris, This paper reports photoluminescence properties of UV emitting fluoride phosphors prepared by wet chemical method. Emission characteristics of these phosphors are found similar to those of commercial UV lamp phosphors with comparable intensities. The usefulness of UV emitting fluoride phosphor is discussed in the paper.

Ca8NaY(PO4)6F2:Eu2+,Mn2+: a potential color-tunable phosphor for white LEDs applications

International Nuclear Information System (INIS)

Fen, Zhang; Wanjun, Tang

2015-01-01

Eu 2+ - and/or Mn 2+ -activated Ca 8 NaY(PO 4 ) 6 F 2 phosphors have been prepared via a combustion-assisted synthesis route. The powder X-ray diffraction measurement revealed that Ca 8 NaY(PO 4 ) 6 F 2 crystallized in a hexagonal crystal system with the space group P6 3 /m (176). The photoluminescence spectrum of the Eu 2+ single-doped phosphor shows a broad blue emission band peaking at 451 nm under the excitation of UV irradiation. The Eu 2+ -/Mn 2+ -codoped phosphors show a blue emission band and an orange emission band, and the corresponding CIE coordinates intuitively indicate the tunable colors from blue to yellow area. The energy transfer from the Eu 2+ to Mn 2+ ions is demonstrated to be a quadrupole-quadrupole mechanism in terms of the experimental results and analysis of PL spectra and decay curves of the phosphors. The developed phosphors can be efficiently excited in the UV region and exhibit a tunable white-light emission, making them attractive as single-component white-light-emitting conversion phosphors for UV-based white LEDs. (orig.)

UV induced thermoluminescence in rare earth oxide doped phosphors: possible use for UV dosimetry

International Nuclear Information System (INIS)

Yeh, S.-M.; Su, C.-S.

1996-01-01

UV induced thermoluminescent (TL) phenomena in some phosphors doped with rare earth oxides (Gd 2 O 3 :Eu, Gd 2 O 3 :Tb, Gd 2 O 3 :Dy and Y 2 O 3 :EU) have been investigated. Gd 2 O 3 :Eu and Y 2 O 3 :Eu have been found to possess prominent TL phenomena. A stable high temperature glow peak has been found at 345 o C in the cubic (C type) crystalline structure of Gd 2 O 3 :Eu. A more stable high temperature glow peak has also been found at about 380 o C in Y 2 O 3 :Eu. The sensitivity is high enough to be used as UV sensors. TL phenomena in Gd 2 O 3 :Tb and Gd 2 O 3 :Dy have also been investigated, but their TL intensities are much weaker than that of Gd 2 O 3 :Eu or Y 2 O 3 :Eu. On the other hand, all glow peaks of Gd 2 O 3 :Tb and Gd 2 O 3 :Dy are unstable at room temperature, therefore, Gd 2 O 3 :Tb and Gd 2 O 3 :Dy are not suitable for use as UV detectors. According to the above properties, the C type (cubic) crystalline structure of the Gd 2 O 3 :Eu phosphor seems to possess the potential of being the TL material for UV measurement. The position of the high temperature glow peak depends on the total UV exposure. It locates at about 380 o C when this phosphor was irradiated by 302 nm UV at 2.4 mJ.cm -2 exposure, but it shifts to 345 o C at 19.2 mJ.cm -2 or higher exposure. The response curves of this phosphor for various wavelengths, e.g. 253.7 nm, 302 nm, and 365 nm, were also measured. This phosphor is sensitive enough to measure background UV radiations, such as sunlight, bulb light etc. (author)

Concentration quenching of Eu2+ in a thermal-stable yellow phosphor Ca2BO3Cl:Eu2+ for LED application

International Nuclear Information System (INIS)

Zhang Xinguo; Zhang Jilin; Dong Zhiyue; Shi Jianxin; Gong Menglian

2012-01-01

A piece-shaped phosphor Ca 2 BO 3 Cl: Eu 2+ was synthesized by solid-state reaction method. This phosphor exhibited wide absorption in ultra-violet and visible range, and bright yellow emission band centering at 570 nm. The concentration quenching mechanism was verified to be a dipole–dipole interaction, and its critical transfer distance was about 17 Å by both calculated crystal structural method and experimental spectral method. This phosphor has a good thermal stability with a quenching temperature (T 1/2 ) of 200 °C. Yellow and white LEDs were fabricated with this phosphor and near UV chips, and the yellow LED has a high color purity of 97.0% and promising current tolerant property, while the white LED shows a luminous efficiency of 11.68 lm/W. - Highlights: ► Broadband excitable and strong yellow-emitting Ca 2 BO 3 Cl: Eu 2+ phosphor is obtained by solid state reaction. ► Concentration quenching mechanism of Ca 2 BO 3 Cl: Eu 2+ is dipole–dipole interaction. ► Quenching temperature (T 1/2 ) of Ca 2 BO 3 Cl: Eu 2+ is at 200 °C. ► As synthesized material can be used for LED phosphor application.

Luminescent properties of UV excitable blue emitting phosphors MSr4(BO3)3:Ce3+ (M = Li and Na)

International Nuclear Information System (INIS)

Guo Chongfeng; Ding Xu; Seo, Hyo Jin; Ren Zhaoyu; Bai Jintao

2011-01-01

Research highlights: → Novel blue emitting phosphors borate MSr 4 (BO 3 ) 3 (M = Li or Na) were prepared first. → Luminescent properties of phosphors borate MSr 4 (BO 3 ) 3 (M = Li or Na) were investigated extensively as candidates of blue emitting phosphor used for UV excited LED. → The optimal concentrations of dopant Ce 3+ ions in compound MSr 4 (BO 3 ) 3 (M = Li or Na) were determined as 0.05 for Li and x = 0.09 for Na excited by UV light respectively. - Abstract: A series of Ce 3+ doped novel borate phosphors MSr 4 (BO 3 ) 3 (M = Li or Na) were successfully synthesized by traditional solid-state reaction. The crystal structures and the phase purities of samples were characterized by powder X-ray diffraction. The optimal concentrations of dopant Ce 3+ ions in compound MSr 4 (BO 3 ) 3 (M = Li or Na) were determined through the measurements of photoluminescence spectra of phosphors. Ce 3+ doped phosphors MSr 4 (BO 3 ) 3 (M = Li or Na) show strong broad band absorption in UV spectral region and bright blue emission under the excitation of 345 nm light. In addition, the temperature dependences of emission spectra of M 1+x Sr 4-2x Ce x (BO 3 ) 3 (M = Li or Na) phosphors with optimal composition x = 0.05 for Li and x = 0.09 for Na excited under 355 nm pulse laser were also investigated. The experimental results indicate that the M 1+x Sr 4-2x Ce x (BO 3 ) 3 (M = Li or Na) phosphors are promising blue emitting phosphors pumped by UV light.

Novel rare-earth-free yellow Ca5Zn3.92In0.08(V0.99Ta0.01O4)6 phosphors for dazzling white light-emitting diodes.

Science.gov (United States)

Pavitra, E; Raju, G Seeta Rama; Park, Jin Young; Wang, Lili; Moon, Byung Kee; Yu, Jae Su

2015-05-20

White light-emitting diode (WLED) products currently available on the market are based on the blue LED combined with yellow phosphor approach. However, these WLEDs are still insufficient for general illumination and flat panel display (FPD) applications because of their low color-rendering index (CRI UV) LED chips provide more efficient excitation than blue chips, YAG:Ce(3+) phosphors have very weak excitation in the near-UV spectral region. Hence, there is an increasing demand for novel yellow phosphor materials with excitation in the near-UV region. In this work, we report novel self-activated yellow Ca(5)Zn(3.92)In(0.08)(V(0.99)Ta(0.01)O(4))(6) (CZIVT) phosphors that efficiently convert near-UV excitation light into yellow luminescence. The crystal structure and lattice parameters of these CZIVT phosphors are elucidated through Rietveld refinement. Through doping with In(3+) and Ta(5+) ions, the emission intensity is enhanced in the red region, and the Stokes shift is controlled to obtain good color rendition. When a near-UV LED chip is coated with a combination of CZIVT and commercial blue Ba(0.9)Eu(0.1)MgAl(10)O(17) phosphors, a pleasant WLED with a high CRI of 82.51 and a low CCT of 5231 K, which are essential for indoor illumination and FPDs, is achieved.

A potential amber-emitting KCaVO4:Sm3+ nanophosphor for near-UV LEDs

Science.gov (United States)

Biswas, Pankaj; Kumar, Vinay

2018-05-01

The Sm3+ doped KCaVO4 phosphor powders were synthesized via combustion route. The powder X-ray diffraction (pXRD) analysis established the crystalline structure and phase of the phosphor material. Williamson-Hall technique was employed to approximate the mean grain size and lattice micro-strain. The transmission electron microscope (TEM) studies were carried out to confirm the nano-sized grain formation. On 405 nm excitation, the phosphor gave amber emission which was assigned to 4G5/2 → 6HJ/2 (J = 7/2, 9/2) transitions of the Sm3+ ion. The concentration quenching mechanism was studied and the optimum dopant concentration in the phosphor was obtained as 2.0 mol%. The diffuse reflectance (DR) studies were carried out to obtain optical band gap (Eg) and Urbach energy (Ec) of the KCaVO4 phosphor which were estimated as 3.63 eV and 98.6 meV, respectively. The color coordinates (x = 0.61, y = 0.39) of the nanophosphor signified the amber shade in the color gamut. The high luminescent properties of KCaVO4:Sm3+ phosphor suggests that the material can be explored as a potential phosphor to be profitably excited by near-UV LEDs to bridge the amber gap in light emitting diodes (LEDs) for solid state lighting (SSL) applications.

Light Converting Inorganic Phosphors for White Light-Emitting Diodes

Directory of Open Access Journals (Sweden)

Chiao-Wen Yeh

2010-03-01

Full Text Available White light-emitting diodes (WLEDs have matched the emission efficiency of florescent lights and will rapidly spread as light source for homes and offices in the next 5 to 10 years. WLEDs provide a light element having a semiconductor light emitting layer (blue or near-ultraviolet (nUV LEDs and photoluminescence phosphors. These solid-state LED lamps, rather than organic light emitting diode (OLED or polymer light-emitting diode (PLED, have a number of advantages over conventional incandescent bulbs and halogen lamps, such as high efficiency to convert electrical energy into light, reliability and long operating lifetime. To meet with the further requirement of high color rendering index, warm light with low color temperature, high thermal stability and higher energy efficiency for WLEDs, new phosphors that can absorb excitation energy from blue or nUV LEDs and generate visible emissions efficiently are desired. The criteria of choosing the best phosphors, for blue (450-480 nm and nUV (380-400 nm LEDs, strongly depends on the absorption and emission of the phosphors. Moreover, the balance of light between the emission from blue-nUV LEDs and the emissions from phosphors (such as yellow from Y3Al5O12:Ce3+ is important to obtain white light with proper color rendering index and color temperature. Here, we will review the status of phosphors for LEDs and prospect the future development.

Light Converting Inorganic Phosphors for White Light-Emitting Diodes

Science.gov (United States)

Chen, Lei; Lin, Chun-Che; Yeh, Chiao-Wen; Liu, Ru-Shi

2010-01-01

White light-emitting diodes (WLEDs) have matched the emission efficiency of florescent lights and will rapidly spread as light source for homes and offices in the next 5 to 10 years. WLEDs provide a light element having a semiconductor light emitting layer (blue or near-ultraviolet (nUV) LEDs) and photoluminescence phosphors. These solid-state LED lamps, rather than organic light emitting diode (OLED) or polymer light-emitting diode (PLED), have a number of advantages over conventional incandescent bulbs and halogen lamps, such as high efficiency to convert electrical energy into light, reliability and long operating lifetime. To meet with the further requirement of high color rendering index, warm light with low color temperature, high thermal stability and higher energy efficiency for WLEDs, new phosphors that can absorb excitation energy from blue or nUV LEDs and generate visible emissions efficiently are desired. The criteria of choosing the best phosphors, for blue (450−480 nm) and nUV (380−400 nm) LEDs, strongly depends on the absorption and emission of the phosphors. Moreover, the balance of light between the emission from blue-nUV LEDs and the emissions from phosphors (such as yellow from Y3Al5O12:Ce3+) is important to obtain white light with proper color rendering index and color temperature. Here, we will review the status of phosphors for LEDs and prospect the future development.

Ortho-vanadates K3RE(VO4)2 (RE = La, Pr, Eu, Gd, Dy, Y) for near UV-converted phosphors

International Nuclear Information System (INIS)

Qin, Lin; Wei, Dong-Lei; Huang, Yanlin; Qin, Chuanxiang; Cai, Peiqing; Kim, Sun-Il; Seo, Hyo-Jin

2014-01-01

The orthovanadate poly-crystals K 3 RE(VO 4 ) 2 (RE = La, Pr, Eu, Gd, Dy, Y) were synthesized via the solid-state reaction route. The crystal phase formation was verified through X-ray diffraction (XRD) studies and was performed by structural refinements. The optical properties were also investigated in detail. K 3 RE(VO 4 ) 2 (RE = Eu, Dy, Gd, Pr, La, Y) phosphors present different luminescence behaviors: the profiles of excitation and emission spectra, the spectra shift, the luminescence decay lifetimes, the absolute quantum efficiency (QE), and the CIE color coordinates are very different. The luminescence of K 3 RE(VO 4 ) 2 (RE = La, Gd, Y, Pr) presents yellow or yellowish green color, while, K 3 Dy(VO 4 ) 2 and K 3 Eu(VO 4 ) 2 show white and red luminescence, respectively. This was discussed on the base of the different micro-structure, activator centers, and the charge transfer transitions from [VO 4 ] 3− groups in the lattices. K 3 Y(VO 4 ) 2 and K 3 Eu(VO 4 ) 2 show higher QE values of 47.0% and 45.0% at room temperature, respectively. All the phosphors have efficient absorption in the region of near-UV wavelengths or blue wavelength region. This can well match with the light from UV-LED (360–400 nm) or blue LED chips (450–480 nm) based on GaN semiconductor. K 3 RE(VO 4 ) 2 could be suggested to be a potential candidate to give further investigations for the application on near-UV excited white LEDs. - Graphical abstract: A series of orthovanadates K 3 RE(VO 4 ) 2 (RE = Eu, Dy, Gd, Pr, La, Y) have been developed to be new phosphors with rich luminescence colors; there are efficiency excitation in the near UV wavelength region. Compared with the reported vanadate phosphors K 3 R(VO 4 ) 2 has rich luminescence color, rich color, no concentration quenching, and comparable luminescence QE. - Highlights: • A new phosphor of non-doped of K 3 R(VO 4 ) 2 (R = Eu, Dy, Gd, Pr, La, Y) were developed by solid-state reaction route. • The phosphor

Standardization of UV LED measurements

Science.gov (United States)

Eppeldauer, G. P.; Larason, T. C.; Yoon, H. W.

2015-09-01

Traditionally used source spectral-distribution or detector spectral-response based standards cannot be applied for accurate UV LED measurements. Since the CIE standardized rectangular-shape spectral response function for UV measurements cannot be realized with small spectral mismatch when using filtered detectors, the UV measurement errors can be several times ten percent or larger. The UV LEDs produce broadband radiation and both their peaks or spectral bandwidths can change significantly. The detectors used for the measurement of these LEDs also have different spectral bandwidths. In the discussed example, where LEDs with 365 nm peak are applied for fluorescent crack-recognition using liquid penetrant (non-destructive) inspection, the broadband radiometric LED (signal) measurement procedure is standardized. A UV LED irradiance-source was calibrated against an FEL lamp standard to determine its spectral irradiance. The spectral irradiance responsivity of a reference UV meter was also calibrated. The output signal of the reference UV meter was calculated from the spectral irradiance of the UV source and the spectral irradiance responsivity of the reference UV meter. From the output signal, both the integrated irradiance (in the reference plane of the reference meter) and the integrated responsivity of the reference meter were determined. Test UV meters calibrated for integrated responsivity against the reference UV meter, can be used to determine the integrated irradiance from a field UV source. The obtained 5 % (k=2) measurement uncertainty can be decreased when meters with spectral response close to a constant value are selected.

ZnO-nanorods: A possible white LED phosphor

Science.gov (United States)

Sarangi, Sachindra Nath; T., Arun; Ray, Dinseh K.; Sahoo, Pratap Kumar; Nozaki, Shinji; Sugiyama, Noriyuki; Uchida, Kazuo

2017-05-01

The white light-emitting diodes (LEDs) have drawn much attention to replace conventional lighting sources because of low energy consumption, high light efficiency and long lifetime. Although the most common approach to produce white light is to combine a blue LED chip and a yellow phosphor, such a white LED cannot be used for a general lighting application, which requires a broad luminescence spectrum in the visible wavelength range. We have successfully chemically synthesized the ZnO nanorods showing intense broad luminescence in the visible wavelength range and made a white LED using the ZnO nanorods as phosphor excited with a blue LED. Their lengths and diameters were 2 - 10 μm and 200 - 800 nm, respectively. The wurtzite structure was confirmed by the x-ray diffraction measurement. The PL spectrum obtained by exciting the ZnO nanorods with the He-Cd laser has two peaks, one associated with the near band-edge recombination and the other with recombination via defects. The peak intensity of the near band-edge luminescence at 388 nm is much weaker than that of the defect-related luminescence. The latter luminescence peak ranges from 450 to 850 nm and broad enough to be used as a phosphor for a white LED. A white LED has been fabricated using a blue LED with 450 nm emission and ZnO nanorod powders. The LED performances show a white light emission and the electroluminescence measurement shows a stiff increase in white light intensity with increasing blue LED current. The Commission International de1'Eclairage (CIE) chromaticity colour coordinates of 450 nm LED pumped white emission shows a coordinate of (0.31, 0.32) for white LED at 350 mA. These results indicate that ZnO nanorods provides an alternate and effective approach to achieve high-performance white LEDs and also other optoelectronic devices.

Photoluminescence and phosphorescence properties of Sr1-xZn2-y(PO4)2:Eux2+,Mny2+ phosphor for UV-based white-LEDs

International Nuclear Information System (INIS)

Jeong, Junho; Jayasimhadri, M.; Sueb Lee, Ho; Jang, Kiwan; Soo Yi, Soung; Hyun Jeong, Jung; Kim, Changdae

2009-01-01

Sr 1-x Zn 2-y (PO 4 ) 2 :Eu x 2+ ,Mn y 2+ (SZP: Eu x 2+ ,Mn y 2+ ) phosphors (x=0, 0.01 and y=0, 0.01) were prepared by using a stoichiometric solid-state reaction method and their photoluminescence and phosphorescence decay properties were investigated. The emission spectrum of SrZn 2 (PO 4 ) 2 :Eu 0.01 2+ , Mn 0.01 2+ measured under 400 nm excitation was composed of the violettish blue and the emerald green emissioins centered at 421 and 547 nm, respectively. The excitation wavelength of the emission peak at 547 nm was about 421 nm in the excitation spectrum of SZP:Mn 0.01 2+ . Since, this value is equal to the transition energy of Eu 2+ , the energy transfer from Eu 2+ to Mn 2+ in SZP:Eu 0.01 2+ ,Mn 0.01 2+ phosphor has been demonstrated. The CIE chromaticity coordinates of SZP:Eu 0.01 2+ ,Mn 0.01 2+ phosphor were (0.330, 0.328) under the excitation wavelength 375 nm at room temperature. The phosphorescence from SZP:Eu 0.01 2+ ,Mn 0.01 2+ could be seen by naked eyes for few seconds and it has persisted for about 4.4 h while monitoring by using a PMT spectrometer. Therefore, SZP:Eu x 2+ ,Mn y 2+ phosphor may be a potential candidate for the UV-based white light-emitting diodes (LEDs).

Novel yellow-emitting Sr8MgLn(PO4)7:Eu2+ (Ln=Y, La) phosphors for applications in white LEDs with excellent color rendering index.

Science.gov (United States)

Huang, Chien-Hao; Chen, Teng-Ming

2011-06-20

Eu(2+)-activated Sr(8)MgY(PO(4))(7) and Sr(8)MgLa(PO(4))(7) yellow-emitting phosphors were successfully synthesized by solid-state reactions for applications in excellent color rendering index white light-emitting diodes (LEDs). The excitation and reflectance spectra of these phosphors show broad band excitation and absorption in the 250-450 nm near-ultraviolet region, which is ascribed to the 4f(7) → 4f(6)5d(1) transitions of Eu(2+). Therefore, these phosphors meet the application requirements for near-UV LED chips. Upon excitation at 400 nm, the Sr(8)MgY(PO(4))(7):Eu(2+) and Sr(8)MgLa(PO(4))(7):Eu(2+) phosphors exhibit strong yellow emissions centered at 518, 610, and 611 nm with better thermal stability than (Ba,Sr)(2)SiO(4) (570 nm) commodity phosphors. The composition-optimized concentrations of Eu(2+) in Sr(8)MgLa(PO(4))(7):Eu(2+) and Sr(8)MgY(PO(4))(7):Eu(2+) phosphors were determined to be 0.01 and 0.03 mol, respectively. A warm white-light near-UV LED was fabricated using a near-UV 400 nm chip pumped by a phosphor blend of blue-emitting BaMgAl(10)O(17):Eu(2+) and yellow-emitting Sr(8)MgY(PO(4))(7):0.01Eu(2+) or Sr(8)MgLa(PO(4))(7):0.03Eu(2+), driven by a 350 mA current. The Sr(8)MgY(PO(4))(7):0.01Eu(2+) and Sr(8)MgLa(PO(4))(7):0.03Eu(2+) containing LEDs produced a white light with Commission International de I'Eclairage (CIE) chromaticity coordinates of (0.348, 0.357) and (0.365, 0.328), warm correlated color temperatures of 4705 and 4100 K, and excellent color rendering indices of 95.375 and 91.75, respectively. © 2011 American Chemical Society

Luminescent Properties of Sr4Si3O8Cl4:Eu2+, Bi3+ Phosphors for Near UV InGaN-Based Light-Emitting-Diodes

Directory of Open Access Journals (Sweden)

Wangqing Shen

2015-12-01

Full Text Available Sr4Si3O8Cl4 co-doped with Eu2+, Bi3+ were prepared by the high temperature reaction. The structure and luminescent properties of Sr4Si3O8Cl4:Eu2+, Bi3+ were investigated. With the introduction of Bi3+, luminescent properties of these phosphors have been optimized. Compared with Sr3.90Si3O8Cl4:0.10Eu2+, the blue-green phosphor Sr3.50Si3O8Cl4:0.10Eu2+, 0.40Bi3+ shows stronger blue-green emission with broader excitation in near-UV range. Bright blue-green light from the LED means this phosphor can be observed by the naked eye. Hence, it may have an application in near UV LED chips.

The quality study of recycled glass phosphor waste for LED

Science.gov (United States)

Tsai, Chun-Chin; Chen, Guan-Hao; Yue, Cheng-Feng; Chen, Cin-Fu; Cheng, Wood-Hi

2017-02-01

To study the feasibility and quality of recycled glass phosphor waste for LED packaging, the experiments were conducted to compare optical characteristics between fresh color conversion layer and that made of recycled waste. The fresh color conversion layer was fabricated through sintering pristine mixture of Y.A.G. powder [yellow phosphor (Y3AlO12 : Ce3+). Those recycled waste glass phosphor re-melted to form Secondary Molten Glass Phosphor (S.M.G.P.). The experiments on such low melting temperature glass results showed that transmission rates of S.M.G.P. are 9% higher than those of first-sintered glass phosphor, corresponding to 1.25% greater average bubble size and 36% more bubble coverage area in S.M.G.P. In the recent years, high power LED modules and laser projectors have been requiring higher thermal stability by using glass phosphor materials for light mixing. Nevertheless, phosphor and related materials are too expensive to expand their markets. It seems a right trend and research goal that recycling such waste of high thermal stability and quality materials could be preferably one of feasible cost-down solutions. This technical approach could bring out brighter future for solid lighting and light source module industries.

Influence of dome phosphor particle concentration on mid-power LED thermal resistance

NARCIS (Netherlands)

Alexeev, A.; Martin, G.; Hildenbrand, V.D.; Bosschaart, K.J.

2016-01-01

The modern white mid-power LEDs usually contain phosphor particles encapsulated in silicone dome material. The particles convert the blue light emitted from the epitaxial layer and play significant role in thermal processes of LED packages. In this paper the influence of the phosphor particles

Red-emitting LaOF:Eu{sup 3+} phosphors: Synthesis, structure and their Judd–Ofelt analysis for LED applications

Energy Technology Data Exchange (ETDEWEB)

Dhananjaya, N., E-mail: ndhananjayas@gmail.com [Department of Physics, B. M. S. Institute of Technology and Management, Bangalore 560064 (India); Shivakumara, C.; Saraf, Rohit [Solid State and Structural Chemistry Unit, Indian Institute of Science, Bangalore 560012 (India); Nagabhushana, H. [C. N. R. Rao Center for Advanced Materials, Tumkur University, Tumkur 572103 (India)

2016-03-15

Highlights: • Red-emitting LaOF:Eu{sup 3+} phosphors were synthesized via facile solid state route. • Judd–Ofelt intensity parameters and radiative properties were determined from PL data. • CIE color coordinates of LaOF:Eu{sup 3+} phosphor is close to the commercial red phosphors. • Eu{sup 3+}-activated LaOF phosphor is a potential candidate for the production of red component in white LEDs. - Abstract: In the present study, we have synthesized a series of La{sub 1−x}Eu{sub x}OF (0.01 ≤ x ≤ 0.09) phosphors by the conventional solid-state reaction route at relatively low temperature (500 °C) and shorter duration of 2 h. The compounds were crystallized in the rhombohedral structure with the space group R-3m (No. 166). Upon UV excitation (254 nm), the photoluminescence spectra exhibit characteristic luminescence {sup 5}D{sub 0} → {sup 7}F{sub J} (J = 1, 2, 3, and 4) intra-4f shell Eu{sup 3+} ion transitions. An intense red emission peak at 610 nm was observed due to electric dipole ({sup 5}D{sub 0} → {sup 7}F{sub 2}) transition. Judd–Ofelt theory was employed to evaluate various radiative parameters such as radiative emission rates, lifetime, branching and asymmetry ratios. CIE color coordinates confirmed the red emission of the phosphors. The luminescent results reveal that LaOF:Eu{sup 3+} phosphor can be used as potential candidate for developing red component in white LED applications.

KCa4(BO33:Ln3+ (Ln = Dy, Eu, Tb phosphors for near UV excited white–light–emitting diodes

Directory of Open Access Journals (Sweden)

Allu Amarnath Reddy

2013-02-01

Full Text Available A series of doped KCa4(BO33:Ln3+ (Ln: Dy, Eu and Tb compositions were synthesized by solid–state reaction method and their photoluminescent properties were systematically investigated to ascertain their suitability for application in white light emitting diodes. The X–ray diffraction (XRD and nuclear magnetic resonance (MAS–NMR data indicates that Ln3+–ions are successfully occupied the non–centrosymmetric Ca2+ sites, in the orthorhombic crystalline phase of KCa4(BO33 having space group Ama2, without affecting the boron chemical environment. The present phosphor systems could be efficiently excitable at the broad UV wavelength region, from 250 to 350 nm, compatible to the most commonly available UV light–emitting diode (LED chips. Photoluminescence studies revealed optimal near white–light emission for KCa4(BO33 with 5 wt.% Dy3+ doping, while warm white–light (CIE; X = 0.353, Y = 0.369 is obtained at 1wt.% Dy3+ ion concentration. The principle of energy transfer between Eu3+ and Tb3+ also demonstrates the potential white–light from KCa4(BO33:Eu3+,Tb3+ phosphor. Whereas, single Tb3+ and Eu3+–doped systems showed bright green (Tb3+ and red (Eu3+ emissions, respectively. Having structural flexibility along with remarkable chemical/thermal stability and suitable quantum efficiency these phosphors can be promising candidates as white–light–emitter for near UV LEDs.

Luminescence and energy transfer of Tm3+ or/and Dy3+ co-doped in Sr3Y(PO4)3 phosphors with UV excitation for WLEDs

International Nuclear Information System (INIS)

Wang, Jiyou; Wang, Jianbo; Duan, Ping

2014-01-01

Powder samples Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ -yDy 3+ were synthesized by the conventional solid-state reaction method. By appropriate tuning of activator content, the emission color can be adjusted around blue to white and yellow. It was discovered that the energy transfer from Tm 3+ to Dy 3+ was demonstrated to be via the intensity of Dy 3+ emission increase with the increase of Tm 3+ concentration. By changing the doping concentration of Tm 3+ and Dy 3+ in Sr 3 Y(PO 4 ) 3 , white-emitting phosphors are produced by 350 nm excitation wavelength, their corresponding color coordinates are very close to the white color chromaticity coordinates (x=0.33, y=0.33). Finally, Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ −yDy 3+ phosphors could be a good promising single-component white light-emitting UV-convertible phosphor in the field of white LEDs. -- Highlights: • The Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ −yDy 3+ phosphors were synthesized by the conventional solid-state reaction method. • The energy transfer in between Tm 3+ and Dy 3+ was observed and explained. • The phosphors can be efficiently excited by a UV light. • The Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ -yDy 3+ phosphor could be a better candidate white phosphor for UV W-LEDs

Luminescent properties of red-emitting LiSr4B3O(9−3x/2)Nx:Eu2+ phosphor for white-LEDs

International Nuclear Information System (INIS)

Yu Hua; Deng Degang; Xu Shiqing; Yu Cuiping; Yin Haoyong; Nie Qiulin

2012-01-01

An Eu 2+ -activated oxynitride LiSr (4−y) B 3 O (9−3x/2) N x :yEu 2+ red-emitting phosphor was synthesized by solid-state reactions. The synthesized phosphor crystallized in a cubic system with space group Ia–3d. The LiSr 4 B 3 O (9−3x/2) N x :Eu 2+ phosphors exhibited a broad red emission band with a peak at 610 nm and a full width at half maximum of 106 nm under 410 nm excitation, which is ascribed to the 4f 6 5d 1 →4f 7 transition of Eu 2+ . The optimal doped nitrogen concentration was observed to be x=0.75. The average decay times of two different emission centers were estimated to be 568 and 489 ns in the LiSr 3.99 B 3 O 8.25 N 0.5 :0.01Eu 2+ phosphors, respectively. Concentration quenching of Eu 2+ ions occurred at y=0.07, and the critical distance was determined as 17.86 Å. The non-radiative transitions via dipole–dipole interactions resulted in the concentration quenching of Eu 2+ -site emission centers in the LiSr 4 B 3 O 9 host. These results indicate LiSr 4 B 3 O (9−3x/2) N x :Eu 2+ phosphor is promising for application in white near-UV LEDs. - Highlights: ► An oxynitride LiSr 4 B 3 O 9 N:Eu 2+ red-emitting phosphor was prepared at low synthesis temperature. ► The introduced nitrogen improved the excitation and emission intensity of the phosphor. ► The wide excitation band matches well with near-UV LED chips. ► The emission spectrum of the phosphor showed a broad full width at half maximum of about 106 nm.

Properties–structure relationship research on LiCaPO4:Eu2+ as blue phosphor for NUV LED application

International Nuclear Information System (INIS)

Zhang, Xinguo; Mo, Fuwang; Zhou, Liya; Gong, Menglian

2013-01-01

Graphical abstract: The graphical abstract shows the excitation and emission spectrum of LiCaPO 4 :Eu 2+ , and the CIE coordinates of LiCaPO 4 :Eu 2+ . The inset shows the photo of blue LED prepared by LiCaPO 4 :Eu 2+ and NUV chip. It indicates that this phosphor can be excited by UV light and emit strong greenish-blue light. Highlights: •Pure phase blue phosphors of LiCaPO 4 :Eu 2+ with a hexagonal structure were first prepared via solid-state method. •The crystallographic site of Eu 2+ ion in the LiCaPO 4 lattice was identified as 8-fold Ca 2+ site. •The phosphor exhibits excellent thermal stability and the corresponding mechanism was thermal assisted ionization. •Bright and high color purity blue LED prototype based on LiCaPO 4 :Eu 2+ phosphor was fabricated. -- Abstract: Blue-emitting phosphors of Eu 2+ -activated LiCaPO 4 with a hexagonal structure were prepared via a conventional solid-state method. The XRD, PL spectra and thermal quenching were applied to characterize the phosphors. The crystallographic site of Eu 2+ ion in the LiCaPO 4 lattice was identified and discussed. The optimized LiCaPO 4 :0.03Eu 2+ exhibits the bright greenish-blue emission with CIE coordinates of (0.119, 0.155) and a quantum efficiency of 52%. The critical energy-transfer distance was confirmed as ∼18 Å by both calculated crystal structure method and experimental spectral method. The thermal stability of LiCaPO 4 :Eu 2+ was evaluated by temperature-dependent PL spectra, and the thermal quenching mechanism was found to be thermal assisted ionization. Prototype blue LEDs with high color purity and good current stability were fabricated

Microbial UV fluence-response assessment using a novel UV-LED collimated beam system.

Science.gov (United States)

Bowker, Colleen; Sain, Amanda; Shatalov, Max; Ducoste, Joel

2011-02-01

A research study has been performed to determine the ultraviolet (UV) fluence-response of several target non-pathogenic microorganisms to UV light emitting diodes (UV-LEDs) by performing collimated beam tests. UV-LEDs do not contain toxic mercury, offer design flexibility due to their small size, and have a longer operational life than mercury lamps. Comsol Multiphysics was utilized to create an optimal UV-LED collimated beam design based on number and spacing of UV-LEDs and distance of the sample from the light source while minimizing the overall cost. The optimized UV-LED collimated beam apparatus and a low-pressure mercury lamp collimated beam apparatus were used to determine the UV fluence-response of three surrogate microorganisms (Escherichia coli, MS-2, T7) to 255 nm UV-LEDs, 275 nm UV-LEDs, and 254 nm low-pressure mercury lamps. Irradiation by low-pressure mercury lamps produced greater E. coli and MS-2 inactivation than 255 nm and 275 nm UV-LEDs and similar T7 inactivation to irradiation by 275 nm UV-LEDs. The 275 nm UV-LEDs produced more efficient T7 and E. coli inactivation than 255 nm UV-LEDs while both 255 nm and 275 nm UV-LEDs produced comparable microbial inactivation for MS-2. Differences may have been caused by a departure from the time-dose reciprocity law due to microbial repair mechanisms. Copyright © 2010 Elsevier Ltd. All rights reserved.

Concentration quenching of Eu{sup 2+} in a thermal-stable yellow phosphor Ca{sub 2}BO{sub 3}Cl:Eu{sup 2+} for LED application

Energy Technology Data Exchange (ETDEWEB)

Zhang Xinguo; Zhang Jilin; Dong Zhiyue; Shi Jianxin [State Key Laboratory of Optoelectronic Materials and Technologies, Ministry of Education Laboratory of Bioinorganic and Synthetic Chemistry, School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou 510275 (China); Gong Menglian, E-mail: cesgml@mail.sysu.edu.cn [State Key Laboratory of Optoelectronic Materials and Technologies, Ministry of Education Laboratory of Bioinorganic and Synthetic Chemistry, School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou 510275 (China)

2012-04-15

A piece-shaped phosphor Ca{sub 2}BO{sub 3}Cl: Eu{sup 2+} was synthesized by solid-state reaction method. This phosphor exhibited wide absorption in ultra-violet and visible range, and bright yellow emission band centering at 570 nm. The concentration quenching mechanism was verified to be a dipole-dipole interaction, and its critical transfer distance was about 17 A by both calculated crystal structural method and experimental spectral method. This phosphor has a good thermal stability with a quenching temperature (T{sub 1/2}) of 200 Degree-Sign C. Yellow and white LEDs were fabricated with this phosphor and near UV chips, and the yellow LED has a high color purity of 97.0% and promising current tolerant property, while the white LED shows a luminous efficiency of 11.68 lm/W. - Highlights: Black-Right-Pointing-Pointer Broadband excitable and strong yellow-emitting Ca{sub 2}BO{sub 3}Cl: Eu{sup 2+} phosphor is obtained by solid state reaction. Black-Right-Pointing-Pointer Concentration quenching mechanism of Ca{sub 2}BO{sub 3}Cl: Eu{sup 2+} is dipole-dipole interaction. Black-Right-Pointing-Pointer Quenching temperature (T{sub 1/2}) of Ca{sub 2}BO{sub 3}Cl: Eu{sup 2+} is at 200 Degree-Sign C. Black-Right-Pointing-Pointer As synthesized material can be used for LED phosphor application.

Synthesis and Luminescent Characteristics of Ce3+-Activated Borosilicate Blue-Emitting Phosphors for LEDs

Directory of Open Access Journals (Sweden)

Hong Yu

2016-01-01

Full Text Available The phosphors Sr3B2SiO8:Ce3+ have been successfully synthesized via solid-state reaction process. Emission/excitation spectra and photoluminescence decay behaviors were investigated in detail. Under the excitation of 340 nm, the emission spectrum presented an asymmetry emission band extended from 350 to 600 nm, which with the main peak at 425 nm can be fitted in two peaks (23940 cm−1 and 21934 cm−1. The chromaticity coordinates of Sr3-xB2SiO8:xCe3+ are fixed in the blue region; when the intensity of Ce3+ reached the maximum, the chromaticity coordinate is (0.154, 0.088 which is more close to the standard CIE of blue light (0.140, 0.080. The results showed the kind of phosphor may have potential applications in the fields of UV-excited white LEDs.

Instense red phosphors for UV light emitting diode devices.

Science.gov (United States)

Cao, Fa-Bin; Tian, Yan-Wen; Chen, Yong-Jie; Xiao, Lin-Jiu; Liu, Yun-Yi

2010-03-01

Ca(x)Sr1-x-1.5y-0.5zMoO4:yEu3+ zNa+ red phosphors were prepared by solid-state reaction using Na+ as charge supply for LEDs (light emitting diodes). The content of charge compensator, Ca2+ concentration, synthesis temperature, reaction time, and Eu3+ concentration were the keys to improving the properties of luminescence and crystal structure of red phosphors. The photoluminescence spectra shows the red phosphors are effectively excited at 616 nm by 311 nm, 395 nm, and 465 nm light. The wavelengths of 395 and 465 nm nicely match the widely applied emission wavelengths of ultraviolet or blue LED chips. Its chromaticity coordinates (CIE) are calculated to be x = 0.65, y = 0.32. Bright red light can be observed by the naked eye from the LED-based Ca0.60Sr0.25MoO4:0.08Eu3+ 0.06Na+.

Controlling the energy transfer via multi luminescent centers to achieve white light/tunable emissions in a single-phased X2-type Y2SiO5:Eu(3+),Bi(3+) phosphor for ultraviolet converted LEDs.

Science.gov (United States)

Kang, Fengwen; Zhang, Yi; Peng, Mingying

2015-02-16

So far, more than 1000 UV converted phosphors have been reported for potential application in white light-emitting diodes (WLEDs), but most of them (e.g., Y2O2S:Eu, YAG:Ce or CaAlSiN3:Eu) suffer from intrinsic problems such as thermal instability, color aging or re-absorption by commixed phosphors in the coating of the devices. In this case, it becomes significant to search a single-phased phosphor, which can efficiently convert UV light to white lights. Herein, we report a promising candidate of a white light emitting X2-type Y2SiO5:Eu(3+),Bi(3+) phosphor, which can be excitable by UV light and address the problems mentioned above. Single Bi(3+)-doped X2-type Y2SiO5 exhibits three discernible emission peaks at ∼355, ∼408, and ∼504 nm, respectively, upon UV excitation due to three types of bismuth emission centers, and their relative intensity depends tightly on the incident excitation wavelength. In this regard, proper selection of excitation wavelength can lead to tunable emissions of Y2SiO5:Bi(3+) between blue and green, which is partially due to the energy transfer among the Bi centers. As a red emission center Eu(3+) is codoped into Y2SiO5:Bi(3+), energy transfer has been confirmed happening from Bi(3+) to Eu(3+) via an electric dipole-dipole (d-d) interaction. Our experiments reveal that it is easily realizable to create the white or tunable emissions by adjusting the Eu(3+) content and the excitation schemes. Moreover, a single-phased white light emission phosphor, X2-type Y1.998SiO5:0.01Eu(3+),0.01 Bi(3+), has been achieved with excellent resistance against thermal quenching and a QE of 78%. At 200 °C, it preserves >90% emission intensity of that at 25 °C. Consequent three time yoyo experiments of heating-cooling prove no occurrence of thermal degradation. A WLED lamp has been successfully fabricated with a CIE chromaticity coordinate (0.3702, 0.2933), color temperature 4756 K, and color rendering index of 65 by applying the phosphor onto a UV LED

Energy transfer and tunable luminescence of Na{sub 2}(Y,Eu)Mg{sub 2}V{sub 3}O{sub 12} phosphors for white LED applications

Energy Technology Data Exchange (ETDEWEB)

Zheng, Zhang; Wanjun, Tang, E-mail: tangmailbox@126.com

2016-01-15

Highlights: • Iso-structural garnet-type Na{sub 2}(Y,Eu)Mg{sub 2}V{sub 3}O{sub 12} solid solution were synthesized. • Efficient energy transfer from [VO{sub 4}]{sup 3−} to Eu{sup 3+} ions in this phosphor is observed obviously. • Tuning the Y/Eu ratio generates the varied hues from yellowish-green to reddish-orange. • This kind of phosphor can be potentially used in UV pumped LEDs. - Abstract: A series of solid-solution phosphors Na{sub 2}(Y,Eu)Mg{sub 2}V{sub 3}O{sub 12} were prepared using solution combustion reaction. X-ray diffraction studies verified the formation of single phase Na{sub 2}(Y,Eu)Mg{sub 2}V{sub 3}O{sub 12} with garnet structure. Na{sub 2}(Y,Eu)Mg{sub 2}V{sub 3}O{sub 12} phosphors show not only a broad emission band with a maximum at 510 nm due to the [VO{sub 4}]{sup 3−} group but also several sharp emission lines due to the Eu{sup 3+} ions. The energy transfer from [VO{sub 4}]{sup 3−} to Eu{sup 3+} was discussed on the base of the spectral analysis. The color-tunable emissions of the Na{sub 2}(Y,Eu)Mg{sub 2}V{sub 3}O{sub 12} phosphor as a function of Y/Eu ratio are realized by continuously generating the varied hues from yellowish-green to reddish-orange. This indicates that the obtained phosphor may have potential applications in the field of UV-based white LEDs.

Phosphors for LED lamps

Science.gov (United States)

Murphy, James Edward; Manepalli, Satya Kishore; Kumar, Prasanth Nammalwar

2013-08-13

A phosphor, a phosphor blend including the phosphor, a phosphor prepared by a process, and a lighting apparatus including the phosphor blend are disclosed. The phosphor has the formula (Ca.sub.1-p-qCe.sub.pK.sub.q).sub.xSc.sub.y(Si.sub.1-rGa.sub.r).sub.zO.su- b.12+.delta. or derived from a process followed using disclosed amounts of reactants. In the formula, (0

Evaluating UV-C LED disinfection performance and ...

Science.gov (United States)

This study evaluated ultraviolet (UV) light emitting diodes (LEDs) emitting at 260 nm, 280 nm, and the combination of 260|280 nm together for their efficacy at inactivating Escherichia. coli, MS2 coliphage, human adenovirus type 2 (HAdV2), and Bacillus pumilus spores; research included an evaluation of genomic damage. Inactivation by the LEDs was compared with the efficacy of conventional UV sources, the low-pressure (LP) and medium-pressure (MP) mercury vapor lamps. The work also calculated the electrical energy per order of reduction of the microorganisms by the five UV sources.For E. coli, all five UV sources yielded similar inactivation rates. For MS2 coliphage, the 260 nm LED was most effective. For HAdV2 and B. pumilus, the MP UV lamp was significantly more effective than the LP UV and UVC LED sources. When considering electrical energy per order of reduction, the LP UV lamp was the most efficient for E. coli and MS2, and the MPUV and LPUV were equally efficient for HAdV2 and B. pumilus spores. Among the UVC LEDs, the 280 nm LED unit required the least energy per log reduction of E. coli and HAdV2. The 280 nm and 260|280 nm LED units were equally efficient per log reduction of B. pumilus spores, and the 260 nm LED unit required the lowest energy per order of reduction of MS2 coliphage. The combination of the 260 nm and 280 nm UV LED wavelengths was also evaluated for potential synergistic effects. No dual-wavelength synergy was detected for inactivation of

UV-LEDs Efficiently Inactivate DNA and RNA Coliphages

Directory of Open Access Journals (Sweden)

Alyaa M. Zyara

2017-01-01

Full Text Available UV-LEDs are a new method of disinfecting drinking water. Some viruses are very resistant to UV and the efficiency of UV-LEDs to disinfect them needs to be studied. Drinking water was disinfected with UV-LEDs after spiking the water with MS2 and four UV- and/or Cl-resistant coliphages belonging to RNA or DNA coliphages isolated from municipal wastewater. UV-LEDs operating at a wavelength of 270 nm for 2 min with 120 mW of irradiation caused 0.93–2.73 Log10-reductions of coliphages tested in a reactor of a 5.2 L volume. Irradiation time of 10 min in the same system increased the Log10-reductions to 4.30–5.16. Traditional mercury UV (Hg-UV lamp at a 254 nm wavelength caused 0.67–4.08 Log10-reductions in 2 min and 4.56–7.21 Log10-reductions in 10 min in 10 mL of water. All coliphages tested except MS2 achieved 4 Log10-reductions with UV-LEDs at a dose that corresponded to 70 mWs/cm2 using Hg-UV. Thus, UV-LEDs are a promising method of disinfecting UV- and/or Cl-resistant viruses.

Synthesis and photoluminescence characteristics of (Y,Gd)BO3:RE (RE = Eu(3+), Ce(3+), Dy(3+) and Tb(3+)) phosphors for blue chip and near-UV white LEDs.

Science.gov (United States)

Rangari, V V; Singh, V; Dhoble, S J

2016-03-01

A series of Eu(3+)-, Ce(3+)-, Dy(3+)- and Tb(3+)-doped (Y,Gd)BO3 phosphors was synthesized by a solid-state diffusion method. X-Ray diffraction confirmed their hexagonal structure and the scanning electron microscopy results showed crystalline particles. The excitation spectra revealed that (Y,Gd)BO3 phosphors doped with Eu(3+), Ce(3+), Dy(3+) and Tb(3+) are effectively excited with near UV-light of 395 nm/blue light, 364, 351 and 314 nm, respectively. Photoluminescence spectra of Eu(3+)-, Ce(3+)- and Tb(3+)/Dy(3+)-doped phosphor showed intense emission of reddish orange, blue and white light, respectively. The phosphor Y0.60Gd0.38BO3:Ce0.02 showed CIE 1931 color coordinates of (0.158, 0.031) and better color purity compared with commercially available blue BAM:Eu(2+) phosphor. The phosphor (Y,Gd)BO3 doped with Eu(3+), Dy(3+) and Tb(3+) showed CIE 1931 color coordinates of (0.667, 0.332), (0.251, 0.299) and (0.333, 0.391) respectively. Significant photoluminescence characteristics of the prepared phosphors indicate that they might serve as potential candidates for blue chip and near-UV white light-emitting diode applications. Copyright © 2015 John Wiley & Sons, Ltd.

Effect of temperature during UV and gamma irradiations of TL phosphor CaSO4:Dy

International Nuclear Information System (INIS)

Nagpal, J.S.; Pendurkar, H.K.

1979-01-01

Temperature is an important parameter in thermoluminescence studies. Irradiation at enhanced temperatures reduces the γ response of TL phosphor CaSO 4 :Dy. However, in the presence of fluorescent lights, the γ response of the phosphor is enhanced by approximately 20% for temperatures around 60-100 0 C. If the phosphor temperature during UV exposure is kept high, the integrated TL output continues to increase until it reaches 18 times at 160 0 C as compared to that produced by UV exposure at room temperature. (Auth.)

Multichannel Luminescence Properties of Mixed-Valent Eu2+/Eu3+ Coactivated SrAl3BO7 Nanocrystalline Phosphors for Near-UV LEDs.

Science.gov (United States)

Liu, Xiaoming; Xie, Weijie; Lü, Ying; Feng, Jingchun; Tang, Xinghua; Lin, Jun; Dai, Yuhua; Xie, Yu; Yan, Liushui

2017-11-20

Up to now, orchestrating the coexistence of Eu 2+ and Eu 3+ activators in a single host lattice has been an extremely difficult task, especially for the appearance of the characteristic emission of Eu 2+ and Eu 3+ in order to generate white light. Nevertheless, here we demonstrate a new Eu 2+ /Eu 3+ coactivated SrAl 3 BO 7 nanocrystalline phosphor with abundant and excellent multichannel luminescence properties. A series of Eu 2+ /Eu 3+ coactivated SrAl 3 BO 7 nanocrystalline phosphors were prepared through a Pechini-type sol-gel method followed by a reduction process. With excitation of UV/NUV light, the prepared SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphors show not only the characteristic f-f transitions of Eu 3+ ion ( 5 D J → 7 F J,J' , J, J' = 0-3), but also the 5d → 4f transitions of Eu 2+ ion with comparable intensity from 400 to 700 nm in the whole visible spectral region. The luminescence color of the SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphor can be tuned from blue, blue-green, white, and orange to orange-red by changing the excitation wavelength, the overall doping concentration of europium ions (Eu 2+ , Eu 3+ ), and the relative ratio of Eu 2+ to Eu 3+ ions to some extent. A single-phase white-light emission has been realized in SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphor. The obtained SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphor has potential application in the area of NUV white-light-emitting diodes.

UV, blue and red upconversion emission in Tm3+ doped Y2O3 phosphor

International Nuclear Information System (INIS)

Pandey, Anurag; Kaushal Kumar; Rai, Vineet Kumar

2012-01-01

Optimized solution combustion route has been adopted to prepare Tm 3+ doped Y 2 O 3 phosphor. The X-ray diffraction analysis of the doped phosphor for getting the structural information has been performed. Intense UV, blue and red emissions exhibiting narrow band have been monitored using 980 nm diode laser excitation. The origin of UV, blue and red upconversion emissions has been explained based on the available data. (author)

Effect of UV irradiation on different types of luminescence of SrAl2 O4 :Eu,Dy phosphors.

Science.gov (United States)

Jha, Piyush

2016-11-01

This paper reports the luminescence behavior of Sr 0.097 Al 2 O 4 :Eu 0.01 ,Dy 0.02 phosphors under UV-irradiation. The effect of UV-irradiation on afterglow (AG), thermoluminescence (TL) and mechanoluminescence (ML) of Sr 0.097 Al 2 O 4 :Eu 0.01 ,Dy 0.02 phosphors is investigated. The space group of Sr 0.097 Al 2 O 4 :Eu 0.01 ,Dy 0.02 phosphors is monoclinic P2 1 . The prepared phosphors exhibit a long AG, intense TL and ML. It is found that the AG, ML intensity and TL increase with increasing duration of irradiation time. The ML intensity decreases with successive impact of the load onto the phosphors, whereby the diminished ML intensity can be recovered by UV-irradiation. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Luminescent properties of Mg3Ca3(PO4)4: Eu2+ blue-emitting phosphor for white light emitting diodes

International Nuclear Information System (INIS)

Li Yinqun; Deng Degang; Wang Qian; Li Gaofeng; Hua Youjie; Jia Guohua; Huang Lihui; Zhao Shilong; Wang Huanping; Li Chenxia; Xu Shiqing

2012-01-01

A blue-emitting phosphor, Eu 2+ -activated Mg 3 Ca 3 (PO 4 ) 4 phosphor was synthesized by conventional solid-state reaction. X-ray powder diffraction (XRD) analysis confirmed the phase formation. Photoluminescence (PL) results showed that Mg 3 Ca 3 (PO 4 ) 4 : Eu 2+ could be efficiently excited by UV–visible light from 250 to 430 nm, which matched well with the emission wavelengths of near-UV and UV LED chips. The effects of the doped-Eu 2+ concentration in Mg 3 Ca 3 (PO 4 ) 4 : Eu 2+ on the PL were also investigated. The result reveals that Mg 3 Ca 3 (PO 4 ) 4 : Eu 2+ is a potential blue-emitting phosphor for white LEDs. - Graphical Abstract: The excitation spectra show a broad peak from 250 to 430 nm, which means Mg 3 Ca 3 (PO 4 ) 4 : Eu 2+ phosphor can be suitable for application in white LEDs excited by the near-UV and UV LEDs. The emission spectrum peaked at 456 nm with the full-width half-maximum (FWHM) of 102 nm is attributed to the 4f 6 5d 1 –4f 7 transition of the Eu 2+ ion. The asymmetric emission spectra show that Eu 2+ has more one emission center in Mg 3 Ca 3 (PO 4 ) 4 , which can be deconvoluted into at least four Gaussian components peaked at 423, 446, 483 and 510 nm. Highlights: ► Mg 3 Ca 3 (PO 4 ) 4 : Eu 2+ phosphor could be effectively excited by UV chips (360–430 nm). ► Mg 3 Ca 3 (PO 4 ) 4 : Eu 2+ phosphor is a potential blue-emitting phosphor for white LEDs. ► Mg 3 Ca 3 (PO 4 ) 4 : Eu 2+ phosphor shows a broadband emission.

Synthesis and photoluminescence properties of Ba2CaZn2Si6O17:Eu3+ red phosphors for white LED applications

International Nuclear Information System (INIS)

Annadurai, G.; Kennedy, S. Masilla Moses

2016-01-01

Novel pellyite type Ba 2 CaZn 2 Si 6 O 17 :Eu 3+ red emitting phosphors with different Eu 3+ contents were synthesized by the solid state reaction method. The crystal structure, photoluminescence properties and concentration quenching of Ba 2 CaZn 2 Si 6 O 17 :Eu 3+ phosphors were investigated. Powder X-ray diffraction measurements confirmed the structure of the samples. The photoluminescence emission (PL) and excitation (PLE) spectra were measured. The results showed that the dominant hypersensitive red emission peak of the phosphors Ba 2 CaZn 2 Si 6 O 17 :Eu 3+ was located at 613 nm attributed to the Eu 3+ transition ( 5 D 0 → 7 F 2 ) which could be effectively excited by 395 nm (near-UV). The latter band matched well with the emission from the near-UV LED chips. The intensity ratio of 5 D 0 → 7 F 2 to 5 D 0 → 7 F 1 transition showed slight variation with Eu 3+ concentrations. The Eu 3+ emission intensity was maximum for 9 mol%. The luminescence quantum efficiency was determined and also the decay profiles were obtained and analyzed. In addition, the Commission International del'Eclairage (CIE) chromaticity coordinates of Ba 2 CaZn 2 Si 6 O 17 :0.09Eu 3+ phosphor were calculated to be 0.637 and 0.362. The experimental results demonstrated that the Ba 2 CaZn 2 Si 6 O 17 :Eu 3+ red emitting phosphor is a potential candidate for white light emitting diodes (WLEDs) pumped by near-UV chip. - Highlights: • A novel Ba 2 CaZn 2 Si 6 O 17 :Eu 3+ red phosphor was synthesized. • The samples yielded a dominant PL emission of Eu 3+ at 613 nm. • Eu 3+ concentration was optimized to be 9 mol% in Ba 2 CaZn 2 Si 6 O 17. • CIE chromaticity coordinates were estimated from the emission spectrum.

Fluorescence enhancing under UV-NIR simultaneous-excitation in ZnS:Cu,Mn phosphors

Directory of Open Access Journals (Sweden)

L. J. Xie

2012-12-01

Full Text Available The fluorescence properties of a long-lasting phosphor, ZnS:Cu,Mn was studied for the first time under simultaneously excitation of both UV and NIR light. Up to 20% fluorescence enhancement of the phosphor was observed. In the present simultaneously-excitation process, broad-band NIR light was absorbed and converted to visible photons via a single-photon upconversion path. We propose that a novel kind of spectral-conversion material with the unique ability to simultaneously convert both UV and NIR photons can be developed and is promising in the application of enhancing the EQE of solar cells.

Improving radiochromic film's sensitivity by wrapping it with UV phosphor

International Nuclear Information System (INIS)

Geso, Moshi; Ackerly, Trevor; Patterson, William

2004-01-01

The main advantage of radiochromic-film dosimeters is the coupling of rapid full planar-acquisition, high-spatial resolution and dose linearity. Their main limitation, however, is their low radiation sensitivity. This precludes their application to measuring doses below a few Gy. Radiochromic films are sensitive to ultraviolet radiation. In this note the results of exposing radiochromic films to x rays through an UV imaging cassette, which converts and amplifies x rays to UV radiation, are presented. These results indicate a clear increase (around 50%) in radiochromic film's sensitivity to MV x rays (6, 10, and 18 MV) when exposed through the UV phosphor

UV and X radiation effects on the stability of calcium halide phosphate phosphors. 1

International Nuclear Information System (INIS)

Tews, W.

1983-01-01

Intensity losses of several calcium halide phosphate phosphors have been investigated as a function of the time of irradiation with near UV and X radiation. The results show that antimony-containing foreign phases increase such losses. The directly excited manganese centre emission is much more lowered than the sensitized one. Detrimental effects of the 185 nm UV radiation are observable not only in the first minutes of irradiation but also over considerably extended periods. The sensitization effect caused by irradiation in different gases depends on the phosphor, especially on the content of antimony, and can be explained by the sorption of gaseous impurities at the phosphor surface so that the diffusion of photochemical reaction products from the surface is inhibited

Novel Red-Emitting Ba₃Y(BO₃)₃:Bi3+, Eu3+ Phosphors for N-UV White Light-Emitting Diodes.

Science.gov (United States)

Maggay, Irish Valerie B; Liu, Wei-Ren

2018-01-01

Ba3Y(BO3)3:Eu3+, Bi3+ were successfully prepared via a solid-state reaction. The crystallinity, photoluminescence properties, energy transfer and thermal quenching properties were studied. Subjecting Ba3Y(BO3)3:Bi3+ samples to different excitation wavelengths (340-370 nm), obtained blue and green emission ascribed to Bi3+(II) and Bi3+(I) sites, respectively. The influence of these two sites were systematically investigated. Bi3+ efficiently transferred its absorbed energy to neighboring Eu3+ sites by enhancing its luminescence intensity. Moreover, Bi3+ greatly enhanced the excitation spectra of Eu3+ in the N-UV region by 2.26 times which indicates that Ba3Y(BO3)3:Eu3+, Bi3+ can be used as a phosphor for w-LEDs using N-UV LED chips.

III-Nitride Micro and Nano Structures for Solid State Lightning

KAUST Repository

Ben Slimane, Ahmed

2014-01-01

efficacy. Typically, LEDs rely on group-III-nitride materials to generate visible light. One of the techniques to generate white light is to coat blue LEDs with yellow phosphor, or ultraviolet (UV) LEDs with red-green-blue (RGB) phosphor. Other scheme

Effect of frost on phosphorescence for thermographic phosphor thermometry

Science.gov (United States)

Kim, Dong; Kim, Mirae; Kim, Kyung Chun

2017-12-01

In this study, we analyzed phosphorescence lifetime and its accuracy by growing frost for thermographic phosphor thermometry in a low-temperature environment. Mg4FGeO6:Mn particles were coated on an aluminum plate and excited with a UV-LED to obtain phosphorescence signals. The surface temperature was maintained at  -20, -15, -10 °C, and the phosphorescence signal was acquired as the frost grew for 3700 s. The lifetime was calculated and compared with the calibration curve under no-frost conditions. The error of the measured lifetime was within 0.7% of that in the no-frost conditions. A 2D surface temperature profile of the target plate was successfully obtained with the frost formation.

Development and future of ultraviolet light-emitting diodes: UV-LED will replace the UV lamp

Science.gov (United States)

Muramoto, Yoshihiko; Kimura, Masahiro; Nouda, Suguru

2014-06-01

Ultraviolet light-emitting diodes (UV-LEDs) have started replacing UV lamps. The power per LED of high-power LED products has reached 12 W (14 A), which is 100 times the values observed ten years ago. In addition, the cost of these high-power LEDs has been decreasing. In this study, we attempt to understand the technologies and potential of UV-LEDs.

UV and VUV characteristics of (YGd)2O3:Eu phosphor particles prepared by spray pyrolysis from polymeric precursors

International Nuclear Information System (INIS)

Kim, E.J.; Kang, Y.C.; Park, H.D.; Ryu, S.K.

2003-01-01

Red-emitting (YGd) 2 O 3 :Eu phosphor particles, with high luminescence efficiency under vacuum ultraviolet (VUV) and ultraviolet (UV) excitation, were prepared by a large-scale spray pyrolysis process. To control the morphology of phosphor particles under severe preparation conditions, spray solution with polymeric precursors were introduced in spray pyrolysis. The prepared (YGd) 2 O 3 :Eu phosphor particles had spherical shape and filled morphology even after post-treatment irrespective of Gd/Y ratio. In the case of solution with polymeric precursors, long polymeric chains formed by esterification reaction in a hot tubular reactor; the droplets turned into viscous gel, which retarded the precipitation of nitrate salts and promoted the volume precipitation of droplets. The brightness of (YGd) 2 O 3 :Eu phosphor particles increased with increasing gadolinium content, and the Gd 2 O 3 :Eu phosphor had the highest luminescence intensity under UV and VUV excitation. The maximum peak intensity of Gd 2 O 3 :Eu phosphor particles under UV and VUV were 118 and 110% of the commercial Y 2 O 3 :Eu phosphor particles, respectively

Development and future of ultraviolet light-emitting diodes: UV-LED will replace the UV lamp

International Nuclear Information System (INIS)

Muramoto, Yoshihiko; Kimura, Masahiro; Nouda, Suguru

2014-01-01

Ultraviolet light-emitting diodes (UV-LEDs) have started replacing UV lamps. The power per LED of high-power LED products has reached 12 W (14 A), which is 100 times the values observed ten years ago. In addition, the cost of these high-power LEDs has been decreasing. In this study, we attempt to understand the technologies and potential of UV-LEDs. (invited article)

Novel bluish white-emitting CdBaP{sub 2}O{sub 7}:Eu{sup 2+} phosphor for near-UV white-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Derbel, Mouna [Laboratory of Industrial Chemistry, National School of Engineers of Sfax, University of Sfax, BPW 3038 Sfax (Tunisia); Mbarek, Aïcha, E-mail: mbarekaicha@yahoo.fr [Laboratory of Industrial Chemistry, National School of Engineers of Sfax, University of Sfax, BPW 3038 Sfax (Tunisia); Chadeyron, Geneviève [Clermont Université, ENSCCF, Institut de Chimie de Clermont-Ferrand, BP 10448, F-63000 Clermont-Ferrand (France); Clermont Université, Université Blaise Pascal, Institut de Chimie de Clermont-Ferrand, BP 10448, F-63000 Clermont-Ferrand (France); Fourati, Mohieddine [Laboratory of Industrial Chemistry, National School of Engineers of Sfax, University of Sfax, BPW 3038 Sfax (Tunisia); Zambon, Daniel [Clermont Université, Université Blaise Pascal, Institut de Chimie de Clermont-Ferrand, BP 10448, F-63000 Clermont-Ferrand (France); Mahiou, Rachid [Clermont Université, Université Blaise Pascal, Institut de Chimie de Clermont-Ferrand, BP 10448, F-63000 Clermont-Ferrand (France); CNRS, UMR 6296, ICCF, BP 80026, F-63171 Aubiere (France)

2016-08-15

A new bluish white-emitting phosphor based on a phosphate host matrix, CdBaP{sub 2}O{sub 7}:Eu{sup 2+}, was prepared by a conventional solid-state reaction method. The photoluminescence properties were investigated in both ultraviolet (UV) and vacuum ultraviolet (VUV) regions. The band-gaps of Eu-doped CdBaP{sub 2}O{sub 7} powders can be tuned in the ranges of 2.26–2 eV. The Eu{sup 2+}-doped CdBaP{sub 2}O{sub 7} phosphor was efficiently excited at wavelengths of 250–400 nm, which is suitable for the blue emission band for near-UV light-emitting-diode (LED) chips (360–400 nm) and red emission peaks up to 700 nm. CdBaP{sub 2}O{sub 7}:Eu{sup 2+} displays two different luminescence centers, which were suggested to Ba{sup 2+} and Cd{sup 2+} sites in the host. The dependence of luminescence intensity on temperatures was measured. The chromaticity coordinates and activation energy for thermal quenching were reported. The phosphor shows a good thermal stability on temperature quenching.

New down-converter for UV-stable perovskite solar cells: Phosphor-in-glass

Science.gov (United States)

Roh, Hee-Suk; Han, Gill Sang; Lee, Seongha; Kim, Sanghyun; Choi, Sungwoo; Yoon, Chulsoo; Lee, Jung-Kun

2018-06-01

Degradation of hybrid lead halide perovskite by UV light is a crucial issue that limits the commercialization of lead halide perovskite solar cells (PSCs). To address this problem, phosphor-in-glass (PiG) is used to convert UV to visible light. Down-conversion of UV light by PiG dramatically increases UV-stability of PSCs and enables PSCs to harvest UV light that is currently wasted. Performance of PSCs with PiG layer does not change significantly during 100 h-long UV-irradiation, while conventional PSCs degrade quickly by 1 h-long UV-irradiation. After 100 h long UV-irradiation, power conversion efficiency of PSCs with PiG is 440% larger than that of conventional PSCs. This result points a direction toward PSCs which are very stable and highly efficient under UV light.

Long-lived visible luminescence of UV LEDs and impact on LED excited time-resolved fluorescence applications

International Nuclear Information System (INIS)

Jin, D; Connally, R; Piper, J

2006-01-01

We report the results of a detailed study of the spectral and temporal properties of visible emission from three different GaN-based ultraviolet (UV) light emitting diodes (UV LEDs). The primary UV emission in the 360-380 nm band decays rapidly (less than 1 μs) following switch-off; however, visible luminescence (470-750 nm) with a decay lifetime of tens of microseconds was observed at approximately 10 -4 of the UV intensity. For applications of UV LEDs in time-resolved fluorescence (TRF) employing lanthanide chelates, the visible luminescence from the LEDs competes with the target Eu 3+ or Tb 3+ fluorescence in both spectral and temporal domains. A UV band-pass filter (Schott UG11 glass) was therefore used to reduce the visible luminescence of the UV LEDs by three orders of magnitude relative to UV output to yield a practical excitation source for TRF

Crystal structure, thermally stability and photoluminescence properties of novel Sr10(PO4)6O:Eu2+ phosphors

International Nuclear Information System (INIS)

Guo, Qingfeng; Liao, Libing; Mei, Lefu; Liu, Haikun

2015-01-01

A series of novel luminescent phosphors Sr 10 (PO 4 ) 6 O:Eu 2+ with apatite structure were synthesized via a high temperature solid-state reaction. The phase structure, photoluminescence (PL) properties, the PL thermal stability, as well as the fluorescence decay curves of the samples were investigated to characterize the resulting samples, and the selected Sr 9.97 (PO 4 ) 6 O:0.03Eu 2+ phosphor exhibits strong thermal quenching resistance, retaining the luminance of 88.73% at 150 °C. The quenching concentration of Eu 2+ in Sr 10 (PO 4 ) 6 O was about 0.03 attributing to the dipole–quadrupole interaction. The Sr 10 (PO 4 ) 6 O:Eu 2+ phosphor exhibited a broad-band blue emission at 439 nm upon excitation at 346 nm. The results indicate that Sr 10 (PO 4 ) 6 O:Eu 2+ phosphors have potential applications as near UV-convertible phosphors for white-light UV LEDs. - Graphical abstract: Sr 10 (PO 4 ) 6 O:Eu 2+ phosphors have potential applications as near UV-convertible phosphors for white-light UV LEDs. - Highlights: • Sr 9.97 (PO 4 ) 6 O:0.03Eu 2+ phosphor exhibits strong thermal quenching resistance. • Two different Eu 2+ emission centers exists in Sr 10 (PO 4 ) 6 O. • The activation energy was also estimated for the Eu 2+ luminescence center

Enhancement of Color Rendering Index for White Light LED Lamps by Red Y2O3:EU3+ Phosphor

Directory of Open Access Journals (Sweden)

Tran Hoang Quang Minh

2016-01-01

Full Text Available We present an application of the red Y2O3:Eu3+ dopant phosphor compound for reaching the color rendering index as high as 86. The Multi-Chip White LED lamps (MCW-LEDs with high Correlated Color Temperatures (CCTs including 7000 K and 8500 K are employed in this study. Besides, the impacts of the Y2O3:Eu3+ phosphor on the attenuation of light through phosphor layers of the various packages is also demonstrated based on the Beer-Lambert law. Simulation results provide important conclusion for selecting and developing the phosphor materials in MCW-LEDs manufacturing.

Investigation of UV-LED Initiated Photopolymerisation of Bio-compatible HEMA

OpenAIRE

McDermott, Sharon

2008-01-01

Ultraviolet (UV) fluorescent lamps are widely used in photopolymerisation processes. However, there a number of disadvantages to these lamps, namely, their intensity varies over time and has to be constantly monitored. This thesis is concerned with the possibility of replacing these lamps with UV Light Emitting Diodes (UV-LEDs). A number of emission characteristics of both the fluorescent lamp and the UV-LEDs were measured and compared to ensure that the optical properties of the UV-LEDs were...

Effect of UV irradiation on the apoptosis and necrosis of Jurkat cells using UV LEDs

Science.gov (United States)

Inada, Shunko A.; Amano, Hiroshi; Akasaki, Isamu; Morita, Akimichi; Kobayashi, Keiko

2009-02-01

Phototherapy is a very effective method for treating most of the incurable skin diseases. A fluorescent light bulb is used as a conventional UV light source for this type of therapy. However, infrared radiation from the light source sometimes causes serious problems on patient's health. In addition, the normal part of the skin is irradiated when a large fluorescent light bulb is used. Moreover, a conventional UV irradiation system is heavy and has a short lifetime and a high electrical power consumption. Therefore, a new UV light source for solving the problems of phototherapy is required. To realize low-power-consumption, lightweight and long-lifetime systems, group III nitride-based UV-A1 light-emitting diodes (LEDs) were investigated. We examined the UV LED irradiation of Jurkat cell, which is a tumor cell and more sensitive to UV light than a healthy cell. The numbers of apoptotic and necrotic cells were confirmed to be the same using a UV LED and a conventional lamp system. The UV LED showed the possibility of realizing a new UV light source for phototherapy.

LED-based UV source for monitoring spectroradiometer properties

Science.gov (United States)

Sildoja, Meelis-Mait; Nevas, Saulius; Kouremeti, Natalia; Gröbner, Julian; Pape, Sven; Pendsa, Stefan; Sperfeld, Peter; Kemus, Fabian

2018-06-01

A compact and stable UV monitoring source based on state-of-the-art commercially available ultraviolet light emitting diodes (UV-LEDs) has been developed. It is designed to trace the radiometric stability—both responsivity and wavelength scale—of array spectroradiometers measuring direct solar irradiance in the wavelength range between 300 nm and 400 nm. The spectral irradiance stability of the UV-LED-based light source observed in the laboratory after seasoning (burning-in) the individual LEDs was better than 0.3% over a 12 h period of continuous operation. The integral irradiance measurements of the source over a period of several months, where the UV-LED source was not operated continuously between the measurements, showed stability within 0.3%. In-field measurements of the source with an array spectroradiometer indicated the stability of the source to be within the standard uncertainty of the spectroradiometer calibration, which was within 1% to 2%.

Effection of UV-LED Illuminant on the Curation of Photolatent-amidine Mixed with Bisphenol A Epoxy Acrylate under Printing Conditions

Directory of Open Access Journals (Sweden)

Duan Huawei

2016-01-01

Full Text Available In order to make photocuring ink or coating cured by UV-LED illuminant, we synthesized (4-((hexahydropyrrolo[1,2-a]pyrimidin-1 (2H-ylmethylphenyl(phenylmethanone(PL -DBN and (4-((octahydropyrimido[1,2-a]azepin-1(2H-ylmethylphenyl(phenylmet hanone(PL -DBU as photoinitiators. Different mass fraction of the photoinitiators was mixed with bisphenol A epoxy acrylate, cured by different wavelengths and power of UV-LED illuminant,and investigated the curing effects of photoinitiators on bisphenol A epoxy acrylate. The results show that the conversion of C=C double bonds of bisphenol A epoxy acrylate will increase as the mass fraction of the photoinitiators or the power of UV-LED illuminant increase. In the same conditions, the curing effect of using 365nm UV-LED illuminant on bisphenol A epoxy acrylate is better than using 395nm UV-LED illuminant. PL-DBU has a better curing effect on the bisphenol A epoxy acrylate rather than PL-DBN. When using the 8W/cm2 of 365nm UV-LED illuminant to cure a mixture of 3% PL-DBU and 97% bisphenol A epoxy acrylate, it will be dry completely in 2 seconds, moreover, the conversion reach 79%.

Study and characterization of phosphors excited in the V UV and UV range by the synchrotron radiation

International Nuclear Information System (INIS)

Gerard, I.

1993-01-01

A characterization tool using synchrotron radiation as a light source to record excitation spectra of the visible luminescence of phosphors induced by photons in the V UV and UV range, at several temperatures (10 to 300 K), is developed. The absorption and deexcitation mechanisms in Y F 3 , La F 3 and Th F 4 matrices doped with Eu 3+ , Tb 3+ , Dy 3+ and Er 3+ ions and polluted with oxygen ions, are examined; charge transfer bands appear clearly. The 4 f n to 4 f n-1 5 d transition bands are also observed on the excitation spectra of the visible luminescence of these compounds and two processes are proposed to interpret the energy relaxation. In order to determine the candidates for the color plasma display panel, measurements of luminous and external quantum yields for efficient phosphors are carried out. The Y F 3 :Eu 3+ compound is shown as a good candidate for the red emission in color plasma display panels

Synthesis and Luminescence Properties of Novel Ce(3+)- and Eu(2+)-Doped Lanthanum Bromothiosilicate La3Br(SiS4)2 Phosphors for White LEDs.

Science.gov (United States)

Lee, Szu-Ping; Liu, Shuang-De; Chan, Ting-Shan; Chen, Teng-Ming

2016-04-13

Novel Ce(3+)- and Eu(2+)-doped lanthanum bromothiosilicate La3Br(SiS4)2:Ce(3+)and La3Br(SiS4)2:Eu(2+) phosphors were prepared by solid-state reaction in an evacuated and sealed quartz glass ampule. The La3Br(SiS4)2:Ce(3+) phosphor generates a cyan emission upon excitation at 375 nm, whereas the La3Br(SiS4)2:Eu(2+) phosphor could be excited with extremely broad range from UV to blue region (300 to 600 nm) and generates a reddish-orange broadband emission centered at 640 nm. In addition, thermal luminescence properties of La3Br(SiS4)2:Ce(3+)and La3Br(SiS4)2:Eu(2+) phosphors from 20 to 200 °C were investigated. The combination of a 450 nm blue InGaN-based LED chip with the red-emitting La3Br(SiS4)2:Eu(2+) phosphor, and green-emitting BOSE:Eu(2+) commercial phosphor produced a warm-white light with the CRI value of ∼95 and the CCT of 5,120 K. Overall, these results show that the prepared phosphors may have potential applications in pc-WLED.

Transition of Emission Colours as a Consequence of Heat-Treatment of Carbon Coated Ce3+-Doped YAG Phosphors

Directory of Open Access Journals (Sweden)

Liang-Jun Yin

2017-10-01

Full Text Available To modify the luminescence properties of Ce3+-doped Y3Al5O12 (YAG phosphors, they have been coated with a carbon layer by chemical vapor deposition and subsequently heat-treated at high temperature under N2 atmosphere. Luminescence of the carbon coated YAG:Ce3+ phosphors has been investigated as a function of heat-treatment at 1500 and 1650 °C. The 540 nm emission intensity of C@YAG:Ce3+ is the highest when heated at 1650 °C, while a blue emission at 400–420 nm is observed when heated at 1500 °C but not at 1650 °C. It is verified by X-ray diffraction (XRD that the intriguing luminescence changes are induced by the formation of new phases in C@YAG:Ce3+-1500 °C, which disappear in C@YAG:Ce3+-1650 °C. In order to understand the mechanisms responsible for the enhancement of YAG:Ce3+ emission and the presence of the blue emission observed for C@YAG:Ce3+-1500 °C, the samples have been investigated by a combination of several electron microscopy techniques, such as HRTEM, SEM-CL, and SEM-EDS. This local and cross-sectional analysis clearly reveals a gradual transformation of phase and morphology in heated C@YAG:Ce3+ phosphors, which is related to a reaction between C and YAG:Ce3+ in N2 atmosphere. Through reaction between the carbon layer and YAG host materials, the emission colour of the phosphors can be modified from yellow, white, and then back to yellow under UV excitation as a function of heat-treatment in N2 atmosphere.

Transition of Emission Colours as a Consequence of Heat-Treatment of Carbon Coated Ce3+-Doped YAG Phosphors.

Science.gov (United States)

Yin, Liang-Jun; Dierre, Benjamin; Sekiguchi, Takashi; van Ommen, J Ruud; Hintzen, Hubertus T Bert; Cho, Yujin

2017-10-16

To modify the luminescence properties of Ce 3+ -doped Y₃Al₅O 12 (YAG) phosphors, they have been coated with a carbon layer by chemical vapor deposition and subsequently heat-treated at high temperature under N₂ atmosphere. Luminescence of the carbon coated YAG:Ce 3+ phosphors has been investigated as a function of heat-treatment at 1500 and 1650 °C. The 540 nm emission intensity of C@YAG:Ce 3+ is the highest when heated at 1650 °C, while a blue emission at 400-420 nm is observed when heated at 1500 °C but not at 1650 °C. It is verified by X-ray diffraction (XRD) that the intriguing luminescence changes are induced by the formation of new phases in C@YAG:Ce 3+ -1500 °C, which disappear in C@YAG:Ce 3+ -1650 °C. In order to understand the mechanisms responsible for the enhancement of YAG:Ce 3+ emission and the presence of the blue emission observed for C@YAG:Ce 3+ -1500 °C, the samples have been investigated by a combination of several electron microscopy techniques, such as HRTEM, SEM-CL, and SEM-EDS. This local and cross-sectional analysis clearly reveals a gradual transformation of phase and morphology in heated C@YAG:Ce 3+ phosphors, which is related to a reaction between C and YAG:Ce 3+ in N₂ atmosphere. Through reaction between the carbon layer and YAG host materials, the emission colour of the phosphors can be modified from yellow, white, and then back to yellow under UV excitation as a function of heat-treatment in N₂ atmosphere.

Luminescent properties of green- or red-emitting Eu2+-doped Sr3Al2O6 for LED

International Nuclear Information System (INIS)

Zhang Jilin; Zhang Xinguo; Shi Jianxin; Gong Menglian

2011-01-01

Eu 2+ -doped Sr 3 Al 2 O 6 (Sr 3-x Eu x Al 2 O 6 ) was synthesized by a solid-state reaction under either H 2 and N 2 atmosphere or CO atmosphere. When H 2 was used as the reducing agent, the phosphor exhibited green emission under near UV excitation, while CO was used as the reducing agent, the phosphor mainly showed red emission under blue light excitation. Both emissions belong to the d-f transition of Eu 2+ ion. The relationship between the emission wavelengths and the occupation of Eu 2+ at different crystallographic sites was studied. The preferential substitution of Eu 2+ into different Sr 2+ cites at different reaction periods and the substitution rates under different atmospheres were discussed. Finally, green-emitting and red-emitting LEDs were fabricated by coating the phosphor onto near UV- or blue-emitting InGaN chips. - Highlights: →Sr 3 Al 2 O 6 :Eu 2+ is synthesized by a solid-state reaction under different atmospheres. →Phosphor obtained under H 2 +N 2 atmosphere emits green light under NUV excitation. →Phosphor obtained under CO atmosphere emits red light under blue light excitation. →Different emission wavelengths are due to Eu 2+ in different Sr 2+ sites. →The preferential substitution and the substitution rates of Eu 2+ are discussed.

Utilization of multi-band OFDM modulation to increase traffic rate of phosphor-LED wireless VLC.

Science.gov (United States)

Yeh, Chien-Hung; Chen, Hsing-Yu; Chow, Chi-Wai; Liu, Yen-Liang

2015-01-26

To increase the traffic rate in phosphor-LED visible light communication (VLC), a multi-band orthogonal frequency division multiplexed (OFDM) modulation is first proposed and demonstrated. In the measurement, we do not utilize optical blue filter to increase modulation bandwidth of phosphor-LED in the VLC system. In this proposed scheme, different bands of OFDM signals are applied to different LED chips in a LED lamp, this can avoid the power fading and nonlinearity issue by applying the same OFDM signal to all the LED chips in a LED lamp. Here, the maximum increase percentages of traffic rates are 41.1%, 17.8% and 17.8% under received illuminations of 200, 500 and 1000 Lux, respectively, when the proposed three-band OFDM modulation is used in the VLC system. In addition, the analysis and verification by experiments are also performed.

Investigation of phosphor-LED lamp for real-time half-duplex wireless VLC system

International Nuclear Information System (INIS)

Yeh, Chien-Hung; Chow, Chi-Wai; Chen, Hsing-Yu; Liu, Yen-Liang; Hsu, Dar-Zu

2016-01-01

In this investigation, a 71.3 to 148.4 Mbit s −1 white phosphor-LED visible light communication (VLC) system is proposed and demonstrated under the practical transmission length of 140 to 210 cm. Here, a commercial white-light LED lamp with five cascaded phosphor-LED chips is utilized for illumination and communication simultaneously. In the measurement, we utilize the optical orthogonal frequency division multiplexing quadrature amplitude modulation (OFDM-QAM) with bit-loading algorithm and propose an optimal bias-tee circuit design to improve the modulation bandwidth from 1 MHz to 27 MHz. Moreover, a blue optical filter is not used on the client side. Finally, to realize and demonstrate the real-time transmission performance in the proposed LED VLC system, a commercial OFDM-based digital signal processor (DSP) chip is utilized on the LED lighting side and client side, respectively. Hence, the proposed real-time half-duplex VLC transmission could achieve the 70 Mbit s −1 downstream and upstream data throughputs, under a practical transmission length of 200 cm. (paper)

Development of Dy3+ activated K2MgP2O7 pyrophosphate phosphor for energy saving lamp

International Nuclear Information System (INIS)

Kohale, R.L.; Dhoble, S.J.

2013-01-01

Present work reports, synthesis of Dy 3+ activated K 2 MgP 2 O 7 pyrophosphate phosphor by using modified solid state diffusion that has been studied for its X-ray diffraction pattern (XRD). Furthermore, the chromaticity coordinate values were estimated from emission spectra of K 2 MgP 2 O 7 . The photoluminescence emission spectra of the phosphors having an excitation at around 351 nm (mercury free) showed two distinguishing bands centered at around 485 nm (blue) and 575 nm (yellow) corresponding to 4 F 9/2 → 6 H 15/2 and 4 F9 /2 → 6 H 13/2 transitions of Dy 3+ , respectively. These phosphors have strong absorption in the near UV region. K 2 MgP 2 O 7 pyrophosphate phosphor is suitable for color converter using UV light as the primary light source, which can be used as a blue/yellow phosphor excited by n-UV LED chip and mixed with other color emission phosphors to obtain white light. The 300–400 nm is Hg-free excitation (mercury excitation is 85% 254 nm wavelength of light and 15% other wavelengths), which is characteristic of solid-state lighting phosphors. Hence PL emission in trivalent dysprosium may be efficient photoluminescent materials for solid-state lighting phosphors. The intact study reveals that the present phosphor have promising applications in the lamp industry especially for solid state lighting (mercury-free excited lamp phosphor) and white light LED. -- Highlights: ► Dy 3+ activated pyrophosphate based phosphor prepared by modified solid state diffusion. ► PL emission spectrum of Dy 3+ ion under 351 nm excitation (Hg-free). ► PL emission at 485 nm (blue), 575 nm (yellow) emission. ► K 2 MgP 2 O 7 : Dy 3+ is expected to be a potential candidate for application in n-UV white LEDs and solid state lighting

Bluish-green color emitting Ba2Si3O8:Eu2+ ceramic phosphors for white light-emitting diodes.

Science.gov (United States)

Xiao, F; Xue, Y N; Zhang, Q Y

2009-10-15

This paper reports on the structural and optical properties of Eu(2+) activated Ba(2)Si(3)O(8) ceramic phosphors synthesized by a sol-gel method. The ceramic phosphors have been characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM) and fluorescence measurements. The structural characterization results suggest that the as-prepared phosphors are of single phase monoclinic Ba(2)Si(3)O(8) with rod-like morphology. A broad excitation band ranging from 300 to 410 nm matches well with the ultraviolet (UV) radiation of light-emitting diodes (LEDs). Upon 380 nm UV light excitation, these phosphors emit bluish-green emission centered at 500 nm with color coordination (x=0.25, y=0.40). All the obtained results indicate that the Ba(2)Si(3)O(8):Eu(2+) ceramic phosphors are promising bluish-green candidates for the phosphor-converted white LEDs.

Multispectral UV imaging for determination of the tablet coating thickness

DEFF Research Database (Denmark)

Novikova, Anna; Carstensen, Jens Michael; Zeitler, J. Axel

2017-01-01

The applicability of off-line multispectral ultraviolet (UV) imaging in combination with multivariate data analysis was investigated to determine the coating thickness and its distribution on the tablet surface during lab scale coating. The UV imaging results were compared with the weight gain...... measured for each individual tablet and the corresponding coating thickness and its distribution measured by terahertz pulsed imaging (TPI). Three different tablet formulations were investigated, two of which contained UV active tablet cores. Three coating formulations were applied: Aquacoat® ECD (a mainly...... translucent coating) and Eudragit® NE (a turbid coating containing solid particles). It was shown that UV imaging is a fast and non-destructive method to predict individual tablet weight gain as well as coating thickness. The coating thickness distribution profiles determined by UV imaging correlated...

Planar measurements of spray-induced wall cooling using phosphor thermometry

Science.gov (United States)

Dragomirov, Plamen; Mendieta, Aldo; Abram, Christopher; Fond, Benoît; Beyrau, Frank

2018-03-01

The wall cooling induced by spray impingement is investigated using phosphor thermometry. Thin coatings of zinc oxide (ZnO) phosphor were applied with a transparent chemical binder onto a steel surface. Instantaneous spatially resolved temperatures were determined using the spectral intensity ratio method directly after the injection of UV-grade hexane onto the surface using a commercial gasoline injector. The investigations showed that 2D temperature measurements with high spatial and shot-to-shot precision of, respectively, 0.5 and 0.6 K can be achieved, allowing the accurate resolution of the cooling induced by the spray. The presence of a liquid film over the phosphor coating during measurements showed no noticeable influence on the measured temperatures. However, in some cases a change in the intensity ratio at the spray impingement area, in the form of a permanent "stain", could be observed after multiple injections. The formation of this stain was less likely with increasing annealing time of the coating as well as lower plate operating temperatures during the injection experiments. Finally, the experimental results indicate a noticeable influence of the thickness of the phosphor coating on the measured spray-induced wall cooling history. Hence, for quantitative analysis, a compromise between coating thickness and measurement accuracy needs to be considered for similar applications where the heat transfer rates are very high.

Hydrothermal synthesis and luminescent properties of LnPO4:Tb,Bi (Ln=La,Gd) phosphors under UV/VUV excitation

International Nuclear Information System (INIS)

Wang Yuhua; Wu Chunfang; Wei Jie

2007-01-01

Monoclinic LnPO 4 :Tb,Bi (Ln=La,Gd) phosphors were prepared by hydrothermal reaction and their luminescent properties under ultraviolet (UV) and vacuum ultraviolet (VUV) excitation were investigated. LaPO 4 :Tb,Bi phosphor and GdPO 4 :Tb phosphor showed the strongest emission intensity under 254 and 147 nm excitation, respectively, because of the different energy transfer models. In UV region, Bi 3+ absorbed most energy then transferred to Tb 3+ , but in VUV region it was the host which absorbed most energy and transferred to Tb 3+

High-power UV-LED degradation: Continuous and cycled working condition influence

Science.gov (United States)

Arques-Orobon, F. J.; Nuñez, N.; Vazquez, M.; Segura-Antunez, C.; González-Posadas, V.

2015-09-01

High-power (HP) UV-LEDs can replace UV lamps for real-time fluoro-sensing applications by allowing portable and autonomous systems. However, HP UV-LEDs are not a mature technology, and there are still open issues regarding their performance evolution over time. This paper presents a reliability study of 3 W UV-LEDs, with special focus on LED degradation for two working conditions: continuous and cycled (30 s ON and 30 s OFF). Accelerated life tests are developed to evaluate the influence of temperature and electrical working conditions in high-power LEDs degradation, being the predominant failure mechanism the degradation of the package. An analysis that includes dynamic thermal and optical HP UV-LED measurements has been performed. Static thermal and stress simulation analysis with the finite element method (FEM) identifies the causes of package degradation. Accelerated life test results prove that HP UV-LEDs working in cycled condition have a better performance than those working in continuous condition.

Photoionization behavior of Eu2+-doped BaMgSiO4 long-persisting phosphor upon UV irradiation

International Nuclear Information System (INIS)

Li, Y.; Wang, Y.; Gong, Y.; Xu, X.; Zhang, F.

2011-01-01

Highlights: → Photoionization behavior of BaMgSiO 4 :Eu 2+ long persistent phosphor upon UV irradiation. → Green phosphorescence was obtained from BaMgSiO 4 :Eu 2+ . → The ionization of Eu 2+ to Eu 3+ was observed in BaMgSiO 4 :Eu 2+ . → The photogenerated Eu 3+ cannot change back to its divalent state at room temperature. → The phosphorescence is associated with the formation forming Eu 3+ -e - pairs. - Abstract: The fluorescence, phosphorescence and thermoluminescence properties of Eu-doped BaMgSiO 4 phosphors sintered in air and in a reducing atmosphere were investigated. Phosphorescence of phosphor sintered in a reducing atmosphere can last for 1.5 h at a recognizable intensity level, whereas phosphorescence of air-sintered phosphor can only persist for 6 min. In addition, a distinction between the shape of the fluorescence spectrum and its corresponding phosphorescence spectrum is observed in the former case. Ionization of Eu 2+ to Eu 3+ upon UV irradiation is observed in the phosphor prepared in a reducing atmosphere, but there is no indication that the photogenerated Eu 3+ cannot change back to its divalent state at room temperature after the excitation source is switched off. In addition, phosphor sintered in a reducing atmosphere shows photochromism upon UV irradiation. No such photoionization and photochromism behavior is observed for the air-sintered phosphor. A possible Eu 2+ photoionization mechanism is constructed on the basis of these experimental observations. The photoionization mechanism presented can also successfully explain the fluorescence and phosphorescence behavior of Eu in BaMgSiO 4 .

Tunable white light of a Ce3+,Tb3+,Mn2+ triply doped Na2Ca3Si2O8 phosphor for high colour-rendering white LED applications: tunable luminescence and energy transfer.

Science.gov (United States)

Lü, Wei; Xu, Huawei; Huo, Jiansheng; Shao, Baiqi; Feng, Yang; Zhao, Shuang; You, Hongpeng

2017-07-18

A tunable white light emitting Na 2 Ca 3 Si 2 O 8 :Ce 3+ ,Tb 3+ ,Mn 2+ phosphor with a high color rendering index (CRI) has been prepared. Under UV excitation, Na 2 Ca 3 Si 2 O 8 :Ce 3+ phosphors present blue luminescence and exhibit a broad excitation ranging from 250 to 400 nm. When codoping Tb 3+ /Mn 2+ ions into Na 2 Ca 3 Si 2 O 8 , energy transfer from Ce 3+ to Tb 3+ and Ce 3+ to Mn 2+ ions is observed from the spectral overlap between Ce 3+ emission and Tb 3+ /Mn 2+ excitation spectra. The energy-transfer efficiencies and corresponding mechanisms are discussed in detail. The mechanism of energy transfer from Ce 3+ to Tb 3+ is demonstrated to be a dipole-quadrupole mechanism by the Inokuti-Hirayama model. The wavelength-tunable white light can be realized by coupling the emission bands centered at 440, 550 and 590 nm ascribed to the contribution from Ce 3+ , Tb 3+ and Mn 2+ , respectively. The commission on illumination value of color tunable emission can be tuned by controlling the content of Ce 3+ , Tb 3+ and Mn 2+ . Temperature-dependent luminescence spectra proved the good thermal stability of the as-prepared phosphor. White LEDs with CRI = 93.5 are finally fabricated using a 365 nm UV chip and the as-prepared Na 2 Ca 3 Si 2 O 8 :Ce 3+ ,Tb 3+ ,Mn 2+ phosphor. All the results suggest that Na 2 Ca 3 Si 2 O 8 :Ce 3+ ,Tb 3+ ,Mn 2+ can act as potential color-tunable and single-phase white emission phosphors for possible applications in UV based white LEDs.

Comparison of UV-LED and low pressure UV for water disinfection: Photoreactivation and dark repair of Escherichia coli.

Science.gov (United States)

Li, Guo-Qiang; Wang, Wen-Long; Huo, Zheng-Yang; Lu, Yun; Hu, Hong-Ying

2017-12-01

Studies on ultraviolet light-emitting diode (UV-LED) water disinfection have shown advantages, such as safety, flexible design, and lower starting voltages. However, information about reactivation after UV-LED disinfection is limited, which is an important issue of UV light-based technology. In this study, the photoreactivation and dark repair of Escherichia coli after UV-LEDs and low pressure (LP) UV disinfection were compared. Four UV-LED units, 265 nm, 280 nm, the combination of 265 + 280 (50%), and 265 + 280 (75%) were tested. 265 nm LEDs was more effective than 280 nm LEDs and LP UV lamps for E. coli inactivation. No synergic effect for disinfection was observed from the combination of 265 and 280 nm LEDs. 265 nm LEDs had no different reactivation performances with that of LP UV, while 280 nm LEDs could significantly repress photoreactivation and dark repair at a low irradiation intensity of 6.9 mJ/cm 2 . Furthermore, the UV-induced damage of 280 nm LEDs was less repaired which was determined by endonuclease sensitive site (ESS) assay. The impaired protein activities by 280 nm LEDs might be one of the reasons that inhibited reactivation. A new reactivation rate constant, K max , was introduced into the logistic model to simulate the reactivation data, which showed positive relationship with the maximum survival ratio and was more reasonable to interpret the results of photoreactivation and dark repair. This study revealed the distinct roles of different UV lights in disinfection and reactivation, which is helpful for the future design of UV-LED equipment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tunable blue-green color emitting phosphors Sr{sub 3}YNa(PO{sub 4}){sub 3}F:Eu{sup 2+}, Tb{sup 3+} based on energy transfer for near-UV white LEDs

Energy Technology Data Exchange (ETDEWEB)

Jin, Yahong, E-mail: yhjin@gdut.edu.cn; Lv, Yang; Hu, Yihua, E-mail: huyh@gdut.edu.cn; Chen, Li; Ju, Guifang; Mu, Zhongfei

2017-05-15

A series of Eu{sup 2+} and Tb{sup 3+} doped Sr{sub 3}YNa(PO{sub 4}){sub 3}F phosphors have been synthesized via a high temperature solid state reaction method. Eu{sup 2+} activated Sr{sub 3}YNa(PO{sub 4}){sub 3}F phosphors can be efficiently excited by light in the range of 220–420 nm, which matches well with the commercial n-UV LEDs, and show intense blue emission centered at 456 nm. The optimal doping concentration of Eu{sup 2+} is determined to be 1 mol%. The concentration quenching mechanism of Eu{sup 2+} in SYNPF host is mainly attributed to the dipole-dipole interaction. Energy transfer from Eu{sup 2+} to Tb{sup 3+} is observed when Eu{sup 2+} and Tb{sup 3+} are co-doped into Sr{sub 3}YNa(PO{sub 4}){sub 3}F host. Under excitation of 380 nm, the emission color can be varied from blue to green along with the increase of Tb{sup 3+} doping concentration. Based on decay curves, the energy transfer from the Eu{sup 2+} to Tb{sup 3+} ions is demonstrated to be a dipole–dipole mechanism. According to thermal quenching study by yoyo experiments of heating-cooling, Sr{sub 3}YNa(PO{sub 4}){sub 3}F:Eu{sup 2+}, Tb{sup 3+} shows good thermal stability. The thermal quenching mechanism is also discussed. The results indicate that as-prepared samples might be of potential application in w-LEDs.

Tunable blue-green emission and energy transfer properties in β-Ca3(PO4)2:Eu(2+), Tb(3+) phosphors with high quantum efficiencies for UV-LEDs.

Science.gov (United States)

Li, Kai; Zhang, Yang; Li, Xuejiao; Shang, Mengmeng; Lian, Hongzhou; Lin, Jun

2015-03-14

A series of Eu(2+) and Tb(3+) singly-doped and co-doped β-Ca3(PO4)2 phosphors have been synthesized via the high-temperature solid-state reaction method. Thermogravimetric (TG) analysis, fourier transform infrared (FT-IR) spectra, X-ray diffraction (XRD) patterns and Rietveld refinements, photoluminescence (PL) spectra including temperature-dependent PL and quantum efficiency, and fluorescence decay lifetimes have been used to characterise the as-prepared samples. Under UV excitation, β-Ca3(PO4)2:Eu(2+) presents a broad emission band centered at 415 nm, which can be decomposed into five symmetrical bands peaking at 390, 408, 421, 435 and 511 nm based on the substitution of five kinds of Ca(2+) sites by Eu(2+) ions. β-Ca3(PO4)2:Tb(3+) shows characteristic emission lines under Tb(3+) 4f-5d transition excitation around 223 nm. In β-Ca3(PO4)2:Eu(2+), Tb(3+) phosphors, similar excitation spectra monitored at 415 and 547 nm have been observed, which illustrates the possibility of energy transfer from Eu(2+) to Tb(3+) ions. The variations in the emission spectra and decay lifetimes further demonstrate the existence of energy transfer from Eu(2+) to Tb(3+) ions under UV excitation. The energy transfer mechanism has been confirmed to be dipole-quadrupole, which can be validated via the agreement of critical distances obtained from the concentration quenching (12.11 Å) and spectrum overlap methods (9.9-13.2 Å). The best quantum efficiency can reach 90% for the β-Ca3(PO4)2:0.01Eu(2+), 0.15Tb(3+) sample under 280 nm excitation. These results show that the developed phosphors may possess potential applications in UV-pumped white light-emitting diodes.

A novel UV-emitting phosphor: LiSr4(BO3)3: Pb2+

International Nuclear Information System (INIS)

Pekgözlü, İlhan

2013-01-01

Pure and Pb 2+ doped LiSr 4 (BO 3 ) 3 materials were prepared by a solution combustion synthesis method. The phase analysis of all synthesized materials were determined using the powder XRD. The synthesized materials were investigated using spectrofluorometer at room temperature. The excitation and emission bands of LiSr 4 (BO 3 ) 3 : Pb 2+ were observed at 284 and 328 nm, respectively. The dependence of the emission intensity on the Pb 2+ concentration for the LiSr 4 (BO 3 ) 3 were studied in detail. It was observed that the concentration quenching of Pb 2+ in LiSr 4 (BO 3 ) 3 is 0.005 mol. The Stokes shifts of LiSr 4 (BO 3 ) 3 : Pb 2+ phosphor was calculated to be 4723 cm –1 . -- Highlights: • A novel UV-emitting phosphor: LiSr 4 (BO 3 ) 3 : Pb 2+ ” synthesized for the first time. • The emission band of LiSr 4 (BO 3 ) 3 : Pb 2+ was observed at 328 nm upon excitation with 284 nm. • LiSr 4 (BO 3 ) 3 : Pb 2+ is a good phosphor for broadband UV application

Multispectral UV Imaging for Determination of the Tablet Coating Thickness.

Science.gov (United States)

Novikova, Anna; Carstensen, Jens M; Zeitler, J Axel; Rades, Thomas; Leopold, Claudia S

2017-06-01

The applicability of off-line multispectral UV imaging in combination with multivariate data analysis was investigated to determine the coating thickness and its distribution on the tablet surface during lab-scale coating. The UV imaging results were compared with the weight gain measured for each individual tablet and the corresponding coating thickness and its distribution measured by terahertz pulsed imaging (TPI). Three different tablet formulations were investigated, 2 of which contained UV-active tablet cores. Three coating formulations were applied: Aquacoat® ECD (a mainly translucent coating) and Eudragit® NE (a turbid coating containing solid particles). It was shown that UV imaging is a fast and nondestructive method to predict individual tablet weight gain as well as coating thickness. The coating thickness distribution profiles determined by UV imaging correlated to the results of the TPI measurements. UV imaging appears to hold a significant potential as a process analytical technology tool for determination of the tablet coating thickness and its distribution resulting from its high measurement speed, high molar absorptivity, and a high scattering coefficient, in addition to relatively low costs. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Near-UV and blue wavelength excitable Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} high efficiency red phosphors

Energy Technology Data Exchange (ETDEWEB)

Khanna, A. [Smart Lighting Engineering Research Center, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Electrical Computer and Systems Engineering, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Dutta, P.S., E-mail: duttap@rpi.edu [Smart Lighting Engineering Research Center, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Electrical Computer and Systems Engineering, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States)

2015-05-15

Red phosphors with narrow emission around 615 nm (with FWHM~5–10 nm) having chemical compositions of A{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} (A=Mg, Sr) have been found to exhibit the highest luminescence amongst the molybdate–tungstate family when excited by sources in the 380–420 nm wavelength range. Thus they are most suitable for enhancing color rendering index and lowering color temperature in phosphor converted white LEDs (pc-WLEDs) with near-UV/blue LED excitation sources. The excitation band edge in the near UV/blue wavelength in the reported phosphor has been attributed to the coordination environment of the transition metal ion (Mo{sup 6+}, W{sup 6+}) and host crystal structure. Furthermore the quantum efficiency of the phosphors has been enhanced by adjusting activator concentration, suitable compositional alloying using substitutional alkaline earth metal cations and charge compensation mechanisms. - Graphical abstract: The charge transfer excitation of orthorhombic Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} is significantly higher than tetragonal CaMoO{sub 4}: Eu{sup 3+} phosphors making Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} prime candidates for fabrication of warm white phosphor-converted LEDs. - Highlights: • LED excitable Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} phosphors were synthesized. • These phosphors are 10 times more intense than CaMoO{sub 4}: Eu{sup 3+} red phosphors. • Their intensity and efficiency were enhanced by materials optimization techniques. • Such techniques include compositional alloying, charge compensation, etc.

Red Emission of SrAl2O4:Mn4+ Phosphor for Warm White Light-Emitting Diodes

Science.gov (United States)

Chi, N. T. K.; Tuan, N. T.; Lien, N. T. K.; Nguyen, D. H.

2018-05-01

In this work, SrAl2O4:Mn4+ phosphor is prepared by co-precipitation. The phase structure, morphology, composition and luminescent performance of the phosphor are investigated in detail with x-ray diffraction, field emission scanning electron microscopy, steady-state photoluminescence (PL) spectra, and temperature-dependent PL measurements. The phosphor shows a strong red emission peak at ˜ 690 nm, which is due to the transition between electronic levels and the electric dipole transition 2Eg to 4A2g of Mn4+ ions located at the sites with D3d local symmetry. The sample doped with 0.04 mol.% Mn4+ exhibits intense red emission with high thermal stability and appropriate International Commission on Illumination (CIE) coordinates (x = 0.6959, y = 0.2737). It is also found that the phosphor absorption in an extended band from 250 nm to 500 nm has three peaks at 320 nm, 405 nm, and 470 nm, which match well with the emission band of ultraviolet (UV) lighting emission diode (LED) or blue LED chips. These results demonstrate that SrAl2O4:Mn4+ phosphor can play the role of activator in narrow red-emitting phosphor, which is potentially useful in UV (˜ 320 nm) or blue (˜ 460 nm) LED.

Optical properties of SrAl{sub 2−x}Si{sub x}O{sub 4−x}N{sub x}:Eu{sup 2+}, Dy{sup 3+} phosphors for AC-LEDs

Energy Technology Data Exchange (ETDEWEB)

Li, Bowen; Xie, Qidi; Qin, Huanhui [School of Applied Physics and Materials, Wuyi University, Jiangmen, Guangdong 529020 (China); Zhang, Mei, E-mail: zmjenny@163.com [School of Applied Physics and Materials, Wuyi University, Jiangmen, Guangdong 529020 (China); He, Xin; Long, Yongbing [School of Applied Physics and Materials, Wuyi University, Jiangmen, Guangdong 529020 (China); Xing, Lusheng [LED Institute, Wuyi University, Jiangmen, Guangdong 529020 (China)

2016-09-15

Series of green emitting SrAl{sub 2−x}Si{sub x}O{sub 4−x}N{sub x}:Eu{sup 2+}, Dy{sup 3+} phosphors have been synthesized via a high temperature solid-state method. The effects of (SiN){sup +} on phase structural, emission and excitation spectra and decay curves were investigated systematically. The X-ray diffraction (XRD) patterns show that the maximum amount of solubility is about x = 0.10. The emission wavelength can be red-shifted from 509 to 515 nm with increasing (SiN){sup +} concentration. Meanwhile, the average lifetime of samples are shortened from 845.86 to 765.34 ms, which can appropriately compensate for the AC time gap and the emission color of AC-LEDs will be improved. Finally, we use these phosphors and near UV-chips to fabricate LEDs, which show more stable luminescence properties accompanying with the decrease of the luminous efficiency as the (SiN){sup +} content increases. - Highlights: • The incorporation of (SiN){sup +} can shift the emission spectra to a long wavelength. • The color purity of SrAl{sub 2−x}Si{sub x}O{sub 4−x}N{sub x}:Eu{sup 2+}, Dy{sup 3+} phosphor can be improved to 48.65%. • The performance of pc-LEDs confirms (SiN){sup +} can improve the stable of phosphors.

Ge{sup 4+}, Eu{sup 3+}-codoped Y{sub 2}SiO{sub 5} as a novel red phosphor for white LED applications

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yan; Dong, Yuanyuan [School of Materials Science and Engineering, Shanghai Institute of Technology, Shanghai 201418 (China); Wei, Bo [School of Chemistry and Materials Engineering, Changshu Institute of Technology, Changshu 215500 (China); Xu, Jiayue

2017-05-15

The phosphors Y{sub 2}SiO{sub 5}: Ge{sup 4+}, Eu{sup 3+} were synthesized by solid state reaction method assisted by flux, and have been characterized by X-ray powder diffraction and fluorescence spectrometer. The results showed that the phosphors can be effectively excited by near-UV (394 nm), and the major peak is located at 611 nm ascribed to the electric-dipole {sup 5}D{sub 0} → {sup 7}F{sub 2} transition of Eu{sup 3+}, the critical quenching concentration of Eu{sup 3+} in the phosphor is determined to be 15 mol% and the critical transfer distance is calculated as 8.90 Aa. Co-doping Y{sub 2}SiO{sub 5}: Eu{sup 3+} with Ge{sup 4+} helps to improve the luminescence intensity and color purity. The red emission of the phosphor under 394 nm excitation shows a good chromaticity index (0.652, 0.347) compared to commercial red phosphors Y{sub 2}O{sub 2}S: Eu{sup 3+} (0.631, 0.350). The quantum efficiency of the Y{sub 2}Si{sub 0.97}O{sub 5}: 0.03Ge{sup 4+}, 0.15Eu{sup 3+}phosphor under 394 nm excitation is estimated to be 45.24%. It can be concluded that efficient red light emitting diodes were fabricated using Ge{sup 4+}, Eu{sup 3+} co-doped phosphor based on near ultraviolet(NUV) excited LED lights. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Luminescence properties and energy transfer investigations of Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ phosphors

International Nuclear Information System (INIS)

Yang, Zaifa; Xu, Denghui; Sun, Jiayue; Du, Jiangnan; Gao, Xuedong

2016-01-01

Highlights: • A phosphor Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ for UV-based white LEDs was firstly synthesized successfully. • The phase structure and photoluminescence properties of samples were studied in detail. • The energy transfer process from Ce"3"+ to Tb"3"+ ions was illustrated in detail. • Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ phosphor has potential applications as an UV-convertible phosphor for white light emitting diodes. - Abstract: A series of Ce"3"+ or Tb"3"+ doped and Ce"3"+/Tb"3"+ co-doped Sr_3Lu(PO_4)_3 phosphors were prepared via the conventional high temperature solid-state reaction. The phase structure, photoluminescence and energy transfer properties of samples were studied in detail. The optimal proportion of Ce"3"+ single doping is 4 mol% with maximal fluorescence intensity. The Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ phosphor shows both a blue emission (428 nm) from Ce"3"+ and a yellowish-green emission (545 nm) from Tb"3"+ with considerable intensity under ultraviolet (UV) excitation (268 nm). The energy transfer from Ce"3"+ to Tb"3"+ ions takes place in the Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ phosphor on the basis of the analysis of the luminescence spectra. The energy transfer mechanism from Ce"3"+ to Tb"3"+ ions was proved to be dipole–dipole interaction. The energy transfer behaviors in Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ phosphor is also investigated by the lifetime measurement. The results show that this phosphor has potential applications for UV white-light LEDs.

Novel UV-emitting single crystalline film phosphors grown by LPE method

International Nuclear Information System (INIS)

Zorenko, Y.; Gorbenko, V.; Savchyn, V.; Voznyak, T.; Nikl, M.; Mares, J.A.; Winnacker, A.

2010-01-01

This work reports the development of new types of UV-emitting phosphors based on single crystalline films (SCF) of aluminum garnet and perovskite compounds grown by the liquid phase epitaxy method. We consider peculiarities of the growth and the luminescent and scintillation properties of the following four types of UV SCF phosphors: i) Ce-doped SCF of Y-Lu-Al-perovskites with the Ce 3+ emission in the 300-450 nm range of the decay time of 16-17 ns; ii) Pr-doped SCF of Y-Lu-Al garnets and perovskites with the Pr 3+ emission in the 300-400 nm and 235-330 nm ranges with the decay time of 13-19 and 7-8 ns, respectively; iii) La 3+ or Sc 3+ doped SCF of Y-Lu-Al-garnets, emitting in the 280-400 nm range due to formation of the La Y,Lu , Sc Y,Lu and Sc Al centers with decay time of the order of several hundreds of nanoseconds; iv) Bi 3+ doped SCF of garnets with Bi 3+ emission in 275-350 nm with decay time of about 1.9 μs.

Luminescence properties of a single-component Na0.34Ca0.66Al1.66Si2.34O8:Ce3+, Sm3+ phosphor with tunable color tone for UV-pumped LEDs

Science.gov (United States)

Wang, Lei; Dong, Jie; Cui, Cai'e.; Tian, Yue; Huang, Ping

2015-08-01

A series of single-phase Na0.34Ca0.66Al1.66Si2.34O8:Ce3+, Sm3+ (NCASO) phosphors have been synthesized via a high temperature solid-state reaction method. The samples were studied based on photoluminescence (PL), photoluminescence excitation (PLE) spectra and fluorescence decay patterns. The obtained PLE exhibited a strong excitation band in the UV region between 250 and 380 nm. Under 340 nm excitation, NCASO:Ce3+, Sm3+ phosphor showed a broad emission band at 414 nm of Ce3+ and four emission bands from 550 nm to 725 nm of Sm3+. Spectra demonstrate nonradiative energy transfers (ET) occur from Ce3+-Sm3+. The analysis based on Inokuti-Hirayama model indicates that the ET is governed by electric dipole-dipole interaction. Moreover, the emitting colors can be adjusting from blue to white by proper tuning of the relative composition of Ce3+/Sm3+. These results show that NCASO:Ce3+, Sm3+ phosphors can be used as a potential single-phased white-emitting candidate for UV WLEDs.

Enhancement of white-light-emission from single-phase Sr5(PO4)3F:Eu(2+),Mn(2+) phosphors for near-UV white LEDs.

Science.gov (United States)

Feng, Yaomiao; Huang, Jinping; Liu, Lili; Liu, Jie; Yu, Xibin

2015-09-07

A series of single-phase broadband white-light-emitting Sr5(PO4)3F:Eu(2+),Mn(2+) phosphors were prepared by a solid state reaction. The luminescence property, and the crystal and electronic structures of the fluorophosphates were studied by photoluminescence analysis, XRD Rietveld refinement and density functional theory calculation (DFT), respectively. Under near ultraviolet excitation in the 250 to 430 nm wavelength range, the phosphors exhibit two emission bands centered at 440 and 556 nm, caused by the Eu(2+) and Mn(2+) ions. By altering the relative ratios of Eu(2+) and Mn(2+) in the compounds, the emission color could be modulated from blue to white. The efficient energy transfer from the Eu(2+) to Mn(2+) ions could be ascribed to the well crystallized host lattice and the facile substitution of Eu(2+) and Mn(2+) for Sr(2+) sites due to similar ionic radii. A series of fluxes were investigated to improve the photoluminescence intensity. When KCl was used as flux in the synthesis, the photoluminescence intensity of Sr5(PO4)3F:Eu(2+),Mn(2+) was enhanced by 85% compared with no fluxes added. These results demonstrate that the single-phase Sr5(PO4)3F:Eu(2+),Mn(2+) with enhanced luminescence efficiency could be promising as a near UV-convertible direct white-light-emitting phosphor for WLED applications.

Predicting the timing properties of phosphor-coated scintillators using Monte Carlo light transport simulation

International Nuclear Information System (INIS)

Roncali, Emilie; Schmall, Jeffrey P; Viswanath, Varsha; Berg, Eric; Cherry, Simon R

2014-01-01

Current developments in positron emission tomography focus on improving timing performance for scanners with time-of-flight (TOF) capability, and incorporating depth-of-interaction (DOI) information. Recent studies have shown that incorporating DOI correction in TOF detectors can improve timing resolution, and that DOI also becomes more important in long axial field-of-view scanners. We have previously reported the development of DOI-encoding detectors using phosphor-coated scintillation crystals; here we study the timing properties of those crystals to assess the feasibility of providing some level of DOI information without significantly degrading the timing performance. We used Monte Carlo simulations to provide a detailed understanding of light transport in phosphor-coated crystals which cannot be fully characterized experimentally. Our simulations used a custom reflectance model based on 3D crystal surface measurements. Lutetium oxyorthosilicate crystals were simulated with a phosphor coating in contact with the scintillator surfaces and an external diffuse reflector (teflon). Light output, energy resolution, and pulse shape showed excellent agreement with experimental data obtained on 3 × 3 × 10 mm 3  crystals coupled to a photomultiplier tube. Scintillator intrinsic timing resolution was simulated with head-on and side-on configurations, confirming the trends observed experimentally. These results indicate that the model may be used to predict timing properties in phosphor-coated crystals and guide the coating for optimal DOI resolution/timing performance trade-off for a given crystal geometry. Simulation data suggested that a time stamp generated from early photoelectrons minimizes degradation of the timing resolution, thus making this method potentially more useful for TOF-DOI detectors than our initial experiments suggested. Finally, this approach could easily be extended to the study of timing properties in other scintillation crystals, with a

Luminescence properties of Ca2 Ga2 SiO7 :RE phosphors for UV white-light-emitting diodes.

Science.gov (United States)

Jiao, Mengmeng; Lv, Wenzhen; Lü, Wei; Zhao, Qi; Shao, Baiqi; You, Hongpeng

2015-03-16

A series of Eu(2+) -, Ce(3+) -, and Tb(3+) -doped Ca2 Ga2 SiO7 phosphors is synthesized by using a high-temperature solid-state reaction. The powder X-ray diffraction and structure refinement data indicate that our prepared phosphors are single phased and the phosphor crystalizes in a tetrahedral system with the ${P\\bar 42m}$ (113) space group. The Eu(2+) - and Ce(3+) -doped phosphors both have broad excitation bands, which match well with the UV light-emitting diodes chips. Under irradiation of λ=350 nm, Ca2 Ga2 SiO7 :Eu(2+) and Ca2 Ga2 SiO7 :Ce(3+) , Li(+) have green and blue emissions, respectively. Luminescence of Ca2 Ga2 SiO7 :Tb(3+) , Li(+) phosphor varies with the different Tb(3+) contents. The thermal stability and energy-migration mechanism of Ca2 Ga2 SiO7 :Eu(2+) are also studied. The investigation results indicate that the prepared Ca2 Ga2 SiO7 :Eu(2+) and Ca2 Ga2 SiO7 :Ce(3+) , Li(+) samples show potential as green and blue phosphors, respectively, for UV-excited white-light-emitting diodes. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

UV and gamma ray induced thermoluminescence properties of cubic Gd2O3:Er3+ phosphor

Directory of Open Access Journals (Sweden)

Raunak Kumar Tamrakar

2014-10-01

Full Text Available This paper reports the thermoluminescence properties of Er3+ doped gadolinium oxide nanophosphor. The phosphor is prepared by high temperature solid state reaction method. The method is suitable for large scale production. Starting materials used for sample preparation were Gd2O3, Er2O3 (0.5–2.5 mol% and fixed concentration of boric acid using as a flux. The prepared samples were characterized by X-ray diffraction technique and the particle size calculated by Scherer's formula. The surface morphology of prepared phosphor is determined by scanning electron microscopic (SEM technique. Functional group analysis was done by Fourier transform infra-red spectroscopy (FTIR analysis. The elemental analysis of prepared sample was determined by energy dispersive X-ray analysis (EDX and the exact particle size of prepared phosphor for the different concentration of dopant (Er3+ was evaluated by transmission electron microscopy (TEM technique. The prepared phosphors for different concentration of Er3+ were examined by thermoluminescence (TL glow curve for UV and gamma irradiation. The UV 254 nm source was used for UV irradiation and Co60 source was used for gamma irradiation. The samples show well resolved broad peak covered the temperature range 50–250 °C and the peak temperature found at 126 °C for UV irradiation and higher temperature peak at 214 °C for gamma irradiation. The effect of heating rate on TL studies was presented for optimized sample. Here UV irradiated sample shows the formation of shallow trap (surface trapping and the gamma irradiated sample shows the formation of deep trapping. The estimation of trap formation was evaluated by knowledge of trapping parameters. The trapping parameters such as activation energy, order of kinetics and frequency factor were calculated by peak shape method. Here most of the peak shows second order of kinetics. The effect of gamma and UV exposure on TL studies was also examined and it shows linear

Photoluminescence and phosphorescence properties of Sr{sub 1-x}Zn{sub 2-y}(PO{sub 4}){sub 2}:Eu{sub x}{sup 2+},Mn{sub y}{sup 2+} phosphor for UV-based white-LEDs

Energy Technology Data Exchange (ETDEWEB)

Jeong, Junho; Jayasimhadri, M. [Research Institute of Basic Science, Changwon National University, Changwon 641-773 (Korea, Republic of); Sueb Lee, Ho [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Jang, Kiwan, E-mail: kwjang@changwon.ac.k [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Soo Yi, Soung [Department of Photonics, Silla University, Pusan 617-736 (Korea, Republic of); Hyun Jeong, Jung [Department of Physics, Pukyong National University, Pusan 608-737 (Korea, Republic of); Kim, Changdae [Department of Physics, Mokpo National University, Mokpo 534-729 (Korea, Republic of)

2009-07-01

Sr{sub 1-x}Zn{sub 2-y}(PO{sub 4}){sub 2}:Eu{sub x}{sup 2+},Mn{sub y}{sup 2+} (SZP: Eu{sub x}{sup 2+},Mn{sub y}{sup 2+}) phosphors (x=0, 0.01 and y=0, 0.01) were prepared by using a stoichiometric solid-state reaction method and their photoluminescence and phosphorescence decay properties were investigated. The emission spectrum of SrZn{sub 2}(PO{sub 4}){sub 2}:Eu{sub 0.01}{sup 2+}, Mn{sub 0.01}{sup 2+} measured under 400 nm excitation was composed of the violettish blue and the emerald green emissioins centered at 421 and 547 nm, respectively. The excitation wavelength of the emission peak at 547 nm was about 421 nm in the excitation spectrum of SZP:Mn{sub 0.01}{sup 2+}. Since, this value is equal to the transition energy of Eu{sup 2+}, the energy transfer from Eu{sup 2+} to Mn{sup 2+} in SZP:Eu{sub 0.01}{sup 2+},Mn{sub 0.01}{sup 2+} phosphor has been demonstrated. The CIE chromaticity coordinates of SZP:Eu{sub 0.01}{sup 2+},Mn{sub 0.01}{sup 2+} phosphor were (0.330, 0.328) under the excitation wavelength 375 nm at room temperature. The phosphorescence from SZP:Eu{sub 0.01}{sup 2+},Mn{sub 0.01}{sup 2+} could be seen by naked eyes for few seconds and it has persisted for about 4.4 h while monitoring by using a PMT spectrometer. Therefore, SZP:Eu{sub x}{sup 2+},Mn{sub y}{sup 2+}phosphor may be a potential candidate for the UV-based white light-emitting diodes (LEDs).

Mechano-luminescence studies of nano ZnMgAl10O17:Eu phosphor under UV irradiation

Science.gov (United States)

Verma, Akshkumar; Verma, Ashish; Panda, Maheswar

2018-05-01

ZnMgAl10O17:Eu nano phosphors were prepared successfully, using the combustion route by employing urea as a fuel. The structural, and Morphological, properties were measured using x-ray diffraction (XRD) Scanning electron microscopy (SEM) transition electron microscopy. The BET surface area of sample were found to be of ˜13.92 m2/g. The ML (Mechano-luminescence) were measured to the home made instrument. The phosphor showed more strong and high ML intensity to the without UV irradiated material. Therefore ZnMgAl10O17:Eu2+ phosphor may use as a damage sensor and dosimetry material. The ML emission spectra of the Zn0.99MgAl10O17:Eu0.01 phosphor showed the characteristic Eu2+ emission peaks ˜453nm (blue) originating from the transitions 4f65d1→4f7, Therefore ZnMgAl10O17:Eu2+ phosphor may use as a blue phosphor material.

Improved performance of UV-LED by p-AlGaN with graded composition

KAUST Repository

Yan, Jianchang

2010-11-02

AlGaN-based ultraviolet light emitting diodes (UV-LEDs) on AlN/sapphire template were grown by metal organic chemical vapour deposition. The AlN template was characterized by atomic force microscopy and high resolution X-ray diffraction. Atomic force microscopy image shows that the AlN surface is very flat, while high resolution X-ray diffraction results prove the good crystalline quality of the AlN template. A novel structure UV-LED which has several p-AlGaN layers with graded composition is compared with a common structure UV-LED which has a single p-Al0.5Ga0.5N layer. The forward bias voltage at 20 mA driving current for the novel structure UV-LED is nearly 3 V higher than that of the common structure UV-LED, however, the electroluminescence intensity of the former is over two times higher than that of the latter. The total quantum efficiency of the novel structure UV-LED is more than 50% higher than that of the common structure UV-LED. The improvement is considered to be the result of better holes injection efficiency in the novel structure UV-LED. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis and photoluminescence properties of red-emitting Y{sub 6}WO{sub 12}:Eu{sup 3+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Chien, Tzu-Chin; Yang, Ji-Chun; Hwang, Chii-Shyang, E-mail: cshwang@mail.ncku.edu.tw; Yoshimura, Masahiro

2016-08-15

For a system of white-light-emitting diodes (WLEDs) fabricated using near-ultraviolet (UV) LED chips coated with RGB tri-color phosphors, the most important issue is enhancing the efficiency of the red phosphor. Y{sub 6}WO{sub 12}:Eu{sup 3+} phosphor is a potential material that can emit red color under near-UV excitation. This work investigated the luminescence properties of Y{sub 6}WO{sub 12}:Eu{sup 3+} under UV light excitation. The photoluminescence (PL) emission intensity of Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphor from the {sup 5}D{sub 0}→{sup 7}F{sub 2} transition increased with Eu{sup 3+} content until x = 0.9. For x > 0.9, the PL emission intensity decreased due to concentration quenching. The decay time of Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphor for the {sup 5}D{sub 0}→{sup 7}F{sub 2} transition was about 0.6–0.7 ms and did not decrease obviously, which means that there was no nonradiative energy transfer in the phosphor. The asymmetry ratio ({sup 5}D{sub 0} → {sup 7}F{sub 2}/{sup 5}D{sub 0} → {sup 7}F{sub 1}) of Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) was about 2, which caused the PL emission intensity of Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphor from the {sup 5}D{sub 0}→{sup 7}F{sub 2} transition to be higher than that from the {sup 5}D{sub 0}→{sup 7}F{sub 1} transition. The chromaticity coordinates of the Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphor were close to the chromaticity coordinates of the standard red color. The Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.9) phosphor showed the highest quantum efficiency. - Highlights: • Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphors were synthesized via a solid-state reaction. • Strongest excitation peaks observed at 392 nm (near UV) and 463 nm (blue). • The major emission peak of the red phosphor excited by 392 nm was at 605 nm. • The quantum efficiency of Eu{sub x}Y{sub 6–x}WO{sub 12} (x = 0.1–1.0) phosphors

Protocol for Determining Ultraviolet Light Emitting Diode (UV-LED) Fluence for Microbial Inactivation Studies.

Science.gov (United States)

Kheyrandish, Ataollah; Mohseni, Madjid; Taghipour, Fariborz

2018-06-15

Determining fluence is essential to derive the inactivation kinetics of microorganisms and to design ultraviolet (UV) reactors for water disinfection. UV light emitting diodes (UV-LEDs) are emerging UV sources with various advantages compared to conventional UV lamps. Unlike conventional mercury lamps, no standard method is available to determine the average fluence of the UV-LEDs, and conventional methods used to determine the fluence for UV mercury lamps are not applicable to UV-LEDs due to the relatively low power output, polychromatic wavelength, and specific radiation profile of UV-LEDs. In this study, a method was developed to determine the average fluence inside a water suspension in a UV-LED experimental setup. In this method, the average fluence was estimated by measuring the irradiance at a few points for a collimated and uniform radiation on a Petri dish surface. New correction parameters were defined and proposed, and several of the existing parameters for determining the fluence of the UV mercury lamp apparatus were revised to measure and quantify the collimation and uniformity of the radiation. To study the effect of polychromatic output and radiation profile of the UV-LEDs, two UV-LEDs with peak wavelengths of 262 and 275 nm and different radiation profiles were selected as the representatives of typical UV-LEDs applied to microbial inactivation. The proper setup configuration for microorganism inactivation studies was also determined based on the defined correction factors.

Crystal structure and Temperature-Dependent Luminescence Characteristics of KMg4(PO4)3:Eu2+ phosphor for White Light-emitting diodes

Science.gov (United States)

Chen, Jian; Liu, Yangai; Mei, Lefu; Liu, Haikun; Fang, Minghao; Huang, Zhaohui

2015-01-01

The KMg4(PO4)3:Eu2+ phosphor was prepared by the conventional high temperature solid-state reaction. The crystal structure, luminescence and reflectance spectra, thermal stability, quantum efficiency and the application for N-UV LED were studied respectively. The phase formation and crystal structure of KMg4(PO4)3:Eu2+ were confirmed from the powder X-ray diffraction and the Rietveld refinement. The concentration quenching of Eu2+ in the KMg4(PO4)3 host was determined to be 1mol% and the quenching mechanism was certified to be the dipole–dipole interaction. The energy transfer critical distance of as-prepared phosphor was calculated to be about 35.84Å. Furthermore, the phosphor exhibited good thermal stability and the corresponding activation energy ΔE was reckoned to be 0.24eV. Upon excitation at 365nm, the internal quantum efficiency of the optimized KMg4(PO4)3:Eu2+ was estimated to be 50.44%. The white N-UV LEDs was fabricated via KMg4(PO4)3:Eu2+, green-emitting (Ba,Sr)2SiO4:Eu2+, and red-emitting CaAlSiN3:Eu2+ phosphors with a near-UV chip. The excellent color rendering index (Ra = 96) at a correlated color temperature (5227.08K) with CIE coordinates of x = 0.34, y = 0.35 of the WLED device indicates that KMg4(PO4)3:Eu2+ is a promising blue-emitting phosphor for white N-UV light emitting diodes (LEDs). PMID:25855866

Preliminary study on preparation of BCNO phosphor particles using citric acid as carbon source

Energy Technology Data Exchange (ETDEWEB)

Nuryadin, Bebeh W.; Pratiwi, Tripuspita; Faryuni, Irfana D.; Iskandar, Ferry, E-mail: ferry@fi.itb.ac.id; Abdullah, Mikrajuddin; Khairurrijal [Department of Physics, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Ganesha 10 Bandung, Indonesia 40132 (Indonesia); Ogi, Takashi; Okuyama, Kikuo [Department of Chemical Engineering, Graduate School of Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashi Hiroshima, Japan 739-8527 (Japan)

2015-04-16

A citric acid was used as a carbon source in the preparation of boron carbon oxy-nitride (BCNO) phosphor particles by a facile process. The preparation process was conducted at relatively low temperature 750 °C and at ambient pressure. The prepared BCNO phosphors showed a high photoluminescence (PL) performance at peak emission wavelength of 470 nm under excitation by a UV light 365 nm. The effects of carbon/boron and nitrogen/boron molar ratios on the PL properties were also investigated. The result showed that the emission spectra with a wavelength peak ranging from 444 nm to 496 nm can be obtained by varying carbon/boron ratios from 0.1 to 0.9. In addition, the observations showed that the BCNO phosphor material has two excitation peaks located at the 365 nm (UV) and 420 nm (blue). Based on these observations, we believe that the citric acid derived BCNO phosphor particles can be a promising inexpensive material for phosphor conversion-based white LED.

Luminescent properties of (Y,Gd)BO3:Bi3+,RE3+ (RE=Eu, Tb) phosphor under VUV/UV excitation

International Nuclear Information System (INIS)

Zeng Xiaoqing; Im, Seoung-Jae; Jang, Sang-Hun; Kim, Young-Mo; Park, Hyoung-Bin; Son, Seung-Hyun; Hatanaka, Hidekazu; Kim, Gi-Young; Kim, Seul-Gi

2006-01-01

Bi 3+ - and RE 3+ -co-doped (Y,Gd)BO 3 phosphors were prepared and their luminescent properties under vacuum ultraviolet (VUV)/UV excitation were investigated. Strong red emission for (Y,Gd)BO 3 :Bi 3+ ,Eu 3+ and strong green emission for (Y,Gd)BO 3 :Bi 3+ ,Tb 3+ are observed under VUV excitation from 147 to 200 nm with a much broader excitation region than that of single Eu 3+ -doped or Tb 3+ -doped (Y,Gd)BO 3 phosphor. Strong emissions are also observed under UV excitation around 265 nm where as nearly no luminescence is observed for single Eu 3+ -doped or Tb 3+ -doped (Y,Gd)BO 3 . The luminescence enhancement of Bi 3+ - and RE 3+ -co-doped (Y,Gd)BO 3 phosphors is due to energy transfer from Bi 3+ ion to Eu 3+ or Tb 3+ ion not only in the VUV region but also in the UV region. Besides, host sensitization competition between Bi 3+ and Eu 3+ or Tb 3+ is also observed. The investigated phosphors may be preferable for devices with a VUV light 147-200 nm as an excitation source such as PDP or mercury-free fluorescent lamp

Effect of coupled UV-A and UV-C LEDs on both microbiological and chemical pollution of urban wastewaters

International Nuclear Information System (INIS)

Chevremont, A.-C.; Farnet, A.-M.; Coulomb, B.; Boudenne, J.-L.

2012-01-01

Wastewater reuse for irrigation is an interesting alternative for many Mediterranean countries suffering from water shortages. The development of new technologies for water recycling is a priority for these countries. In this study we test the efficiency of UV-LEDs (Ultraviolet-Light-Emitting Diodes) emitting UV-A or UV-C radiations, used alone or coupled, on bacterial and chemical indicators. We monitored the survival of fecal bioindicators found in urban wastewaters and the oxidation of creatinine and phenol which represent either conventional organic matter or the aromatic part of pollution respectively. It appears that coupling UV-A/UV-C i) achieves microbial reduction in wastewater more efficiently than when a UV-LED is used alone, and ii) oxidizes up to 37% of creatinine and phenol, a result comparable to that commonly obtained with photoreactants such as TiO 2 . - Highlights: ► We test UV-LEDs as an urban wastewater tertiary treatment. ► UV-A and UV-C are coupled, combining germicidal and oxidative properties of UV. ► Coupled wavelengths have the most efficient bactericidal effect. ► Coupling UV-A and UV-C leads to photooxidation of creatinine and phenol.

Development of a method for the characterization and operation of UV-LED for water treatment.

Science.gov (United States)

Kheyrandish, Ataollah; Mohseni, Madjid; Taghipour, Fariborz

2017-10-01

Tremendous improvements in semiconductor technology have made ultraviolet light-emitting diodes (UV-LEDs) a viable alternative to conventional UV sources for water treatment. A robust and validated experimental protocol for studying the kinetics of microorganism inactivation is key to the further development of UV-LEDs for water treatment. This study proposes a protocol to operate UV-LEDs and control their output as a polychromatic radiation source. In order to systematically develop this protocol, the results of spectral power distribution, radiation profile, and radiant power measurements of a variety of UV-LEDs are presented. A wide range of UV-LEDs was selected for this study, covering various UVA, UVB, and UVC wavelengths, viewing angles from 3.5° to 135°, and a variety of output powers. The effects of operational conditions and measurement techniques were investigated on these UV-LEDs using a specially designed and fabricated setup. Operating conditions, such as the UV-LED electrical current and solder temperature, were found to significantly affect the power and peak wavelength output. The measurement techniques and equipment, including the detector size, detector distance from the UV-LED, and potential reflection from the environment, were shown to influence the results for many of the UV-LEDs. The results obtained from these studies were analyzed and applied to the development of a protocol for UV-LED characterization. This protocol is presented as a guideline that allows the operation and control of UV-LEDs in any structure, as well as accurately measuring the UV-LED output. Such information is essential for performing a reliable UV-LED assessment for the inactivation of microorganisms and for obtaining precise kinetic data. Copyright © 2017 Elsevier Ltd. All rights reserved.

Color tunable green–yellow–orange–red Er{sup 3+}/Eu{sup 3+}-codoped PbGeO{sub 3}:PbF{sub 2}:CdF{sub 2} glass phosphor for application in white-LED technology

Energy Technology Data Exchange (ETDEWEB)

Souza, W.S.; Domingues, R.O.; Bueno, L.A.; Costa, E.B. da; Gouveia-Neto, A.S., E-mail: artur@df.ufrpe.br

2013-12-15

Color tunable wide gamut light covering the greenish, yellow–green, yellow, orange, and reddish tone chromaticity region in Er{sup 3+}/Eu{sup 3+}-codoped lead–cadmium–germanate PbGeO{sub 3}:PbF{sub 2}:CdF{sub 2} glass phosphor is presented. The phosphors were synthesized, and their light emission properties examined under UV and blue LED excitation. Luminescence emission around 525, 550, 590, 610, and 660 nm was obtained and analyzed as a function of Eu/Er concentration, excitation wavelength, and glass host composition. The color tunability was actually obtained via proper combination of Er{sup 3+} and Eu{sup 3+} active ions concentration. The combination of the emission tone with blue LEDs in the region of 400–460 nm, yielded a mixture of light with color in the white-light region presenting a color correlated temperature in the range of 2000–4000 K. Results indicate that the color-tunable fluorolead germanate erbium/europium co-doped glass phosphor herein reported is a promising novel contender for application in LED-based solid-state illumination technology -- Highlights: • Color tunability in the red–orange–yellow–green spectral region. • White-light generation presenting a CCT in the range of 2000–4000 K. • New europium/erbium co-doped lead–cadmium–germanate glass phosphor.

UV-hardening of coating materials on the basis of unsaturated polyesters

International Nuclear Information System (INIS)

Patheiger, M.; Fuhr, K.

1975-01-01

The UV-hardening of coated materials based on unsaturated polyester resins is successful in practice. Resins, modified by acrylic acid, are gaining importance for thin coating from paper coatings up to printing colours. A report is given on the binding classes which come into question as photo initiators and whose ways of reaction with UV-irradiation are so far known. The photopolymerizeable coating systems can be used from undercoats to coating varnishes and from thick layers (polishing varnishes) to thinnest layers (printing colours). The economical significance of the UV-process today is illustrated by statistics on the use of binding agents and coating materials. (orig./AK) [de

UV-curable polyurethane coatings derived from cellulose

International Nuclear Information System (INIS)

Patel, M. M.; Patel, K. I.; Patel, H. B.; Parmar, J. S.

2009-01-01

At the present time coating industry is devoting much research in the direction of low volatile organic compounds to make eco-friendly coating material. In this study, such materials are developed from cellulose derived from bagasse, a sugar industry waste. Cellulose is converted to cellulose glyco glycoside by acid hydrolysis of cellulose under heterogeneous condition. Cellulose glyco glycoside is treated with polyethylene glycol having different molecular weights to give glyco glycosides which in turn are reacted with various diisocyanates to obtain polyurethane having free NCO groups. These materials are then reacted with hydroxyethylmethacrylate to give polyurethane acrylates. The acrylates are characterized for specific gravity, viscosity, colour and molecular weight as well as by fourier transform infrared spectroscopy. The UV-curable coating composition was prepared by blending PU-acrylate, reactive diluents and photoinitiator. Coating compositions were cured under UV-light and characterized for adhesion, flexibility, impact resistance, solvent resistance and for dynamic mechanical analysis as well as by thermal gravimetric analysis for thermal stability. The cured films give thickness of 23-24 microns and cure time required is less than 1.5-2.0 min. There is no liberation of any volatiles during curing and films have good adhesion to mild steel substrate. The cured coatings give excellent dynamic, mechanical and chemical properties. The scratch resistance was found to be satisfactory. The application was made in unpigmented form but it is found that various pigments can be used to give coloured UV-curable coatings.

The impact of the thermal conductivities of the color conversion elements of phosphor converted LEDs under different current driving schemes

Energy Technology Data Exchange (ETDEWEB)

Fulmek, Paul; Nicolics, Johann [Institute of Sensor & Actuator Systems, Vienna University of Technology, Gusshausstraße 27-29, A-1040 Vienna (Austria); Nemitz, Wolfgang; Schweitzer, Susanne; Sommer, Christian; Hartmann, Paul [Institute of Surface Technologies and Photonics, Joanneum Research Forschungsges mbH, Franz-Pichler Straße 30, A-8160 Weiz (Austria); Schrank, Franz [Tridonic Jennersdorf GmbH, Technologiepark 10, A-8380 Jennersdorf (Austria); Wenzl, Franz P., E-mail: Franz-Peter.Wenzl@joanneum.at [Institute of Sensor & Actuator Systems, Vienna University of Technology, Gusshausstraße 27-29, A-1040 Vienna (Austria)

2016-01-15

For a systematic approach to improve the reliability and the white light quality of phosphor converted light-emitting diodes (LEDs) it is imperative to gain a better understanding of the individual parameters that affect color temperature constancy and maintenance. By means of a combined optical and thermal simulation procedure, in this contribution we give a comprehensive discussion on the impact of different thermal conductivities of the color conversion elements (CCE) of phosphor converted LEDs on their respective thermal load for different current driving schemes. In particular we show that, while for the thermal load of CCEs with low thermal conductivities also effects due to the non-linearity between the blue radiant flux and the current have to be considered, these effects are largely diminished in case of CCEs with higher thermal conductivities. - Highlights: • We discuss the thermal load of phosphor based LEDs for different current driving. • We report on the time scales for the thermal load of phosphor based LEDs. • We report on the impact of the non-linearity of the radiant flux on the thermal load. • We discuss the impact of the thermal conductivity on the thermal load.

Study on preparation of orange-emitting phosphor Y3Mg2AlSi2O12: Ce3+ for wLED

Directory of Open Access Journals (Sweden)

Yan Shirun

2017-12-01

Full Text Available Ce3+-doped garnet-structured orange-emitting phosphor Y3Mg2AlSi2O12:Ce3+ was prepared by sol-gel combustion using urea as a fuel.Effects of the reduction temperature,Ce3+ doping concentration on the structure,morphology,and photoluminescence property of the as-prepared phosphor were investigated by X-ray diffraction(XRD,scaning electron microscope(SEM,photoluminescence spectroscopy and UV-Vis reflection spectroscopy.The crystallinities,morphologies,and photoluminescence properties of the phosphors prepared by sol-gel combustion and solid-state reaction were compared.The reasons causing different performance of the phosphors were discussed.

UV induced photoluminescence and thermally stimulated luminescence of ThO2:Tb3+ phosphor

International Nuclear Information System (INIS)

Godbole, S.V.; Nagpal, J.S.; Page, A.G.

2000-01-01

Thorium oxide doped with trivalent terbium ions offers itself as a novel phosphor with its photo- and thermally-stimulated luminescence (PL and TSL) characteristics showing a marked change on sustained exposure to 254 and 365 nm ultraviolet (UV) radiation. The reduction in luminescence intensity of Tb 3+ ions, on irradiation with 254 nm photons and subsequent restoration on exposure to 365 nm, has been correlated with the complimentary behaviour in UV-induced TSL. These changes are, in turn, ascribed to inter-configurational (f-d) transitions and e-h formation and recombination processes. UV radiation induced TSL output increases linearly with incident UV radiant energy at a constant radiation flux; however, for a fixed exposure, TSL output increases with increase in radiant flux

Wet chemical synthesis and luminescence in Ca5(PO4)3M:Eu2+ (M = Br, I) phosphors for solid state lighting

Science.gov (United States)

Mungmode, C. D.; Gahane, D. H.; Moharil, S. V.

2018-05-01

A simple wet chemical synthesis of Eu2+ activated Ca5(PO4)3Br and Ca5(PO4)3I phosphors and their photoluminescence is reported. Formation of Ca5(PO4)3Br is confirmed by X-ray diffraction (XRD). Synthesized phosphors are analyzed for photoluminescence (PL) spectrum. A bright blue emission is observed when phosphors are excited by near Ultra Violet (nUV) radiations. Photoluminescence emission spectrum for (Ca0.985Eu0.015)5(PO4)3Br is centered at 457 nm and for (Ca0.985Eu0.015)5(PO4)3 I it peaks at 455 nm when excited by 365 nm near UV radiation. Eu2+ luminescence in Ca5(PO4)3Br is reported for the first time. The phosphors can be efficiently excited by nUV radiations. This shows that phosphors may be used as blue phosphor in pcLED for Solid State Lighting.

Effect of coupled UV-A and UV-C LEDs on both microbiological and chemical pollution of urban wastewaters

Energy Technology Data Exchange (ETDEWEB)

Chevremont, A.-C., E-mail: anne-celine.chevremont@imbe.fr [Aix-Marseille Universite - CNRS, FR ECCOREV, Laboratoire Chimie de l' Environnement (FRE3416), Equipe ' Developpements Metrologiques et Chimie des Milieux' , 3 place Victor Hugo, case 29, 13331 Marseille Cedex 3 (France); Aix-Marseille Universite - CNRS, FR ECCOREV, Institut Mediterraneen de Biodiversite et d' Ecologie marine et continentale (UMR7263), Equipe ' Vulnerabilite des Systemes Microbiens' , Avenue Escadrille Normandie-Niemen, Boite 452, 13397 Marseille Cedex 20 (France); Farnet, A.-M. [Aix-Marseille Universite - CNRS, FR ECCOREV, Institut Mediterraneen de Biodiversite et d' Ecologie marine et continentale (UMR7263), Equipe ' Vulnerabilite des Systemes Microbiens' , Avenue Escadrille Normandie-Niemen, Boite 452, 13397 Marseille Cedex 20 (France); Coulomb, B.; Boudenne, J.-L. [Aix-Marseille Universite - CNRS, FR ECCOREV, Laboratoire Chimie de l' Environnement (FRE3416), Equipe ' Developpements Metrologiques et Chimie des Milieux' , 3 place Victor Hugo, case 29, 13331 Marseille Cedex 3 (France)

2012-06-01

Wastewater reuse for irrigation is an interesting alternative for many Mediterranean countries suffering from water shortages. The development of new technologies for water recycling is a priority for these countries. In this study we test the efficiency of UV-LEDs (Ultraviolet-Light-Emitting Diodes) emitting UV-A or UV-C radiations, used alone or coupled, on bacterial and chemical indicators. We monitored the survival of fecal bioindicators found in urban wastewaters and the oxidation of creatinine and phenol which represent either conventional organic matter or the aromatic part of pollution respectively. It appears that coupling UV-A/UV-C i) achieves microbial reduction in wastewater more efficiently than when a UV-LED is used alone, and ii) oxidizes up to 37% of creatinine and phenol, a result comparable to that commonly obtained with photoreactants such as TiO{sub 2}. - Highlights: Black-Right-Pointing-Pointer We test UV-LEDs as an urban wastewater tertiary treatment. Black-Right-Pointing-Pointer UV-A and UV-C are coupled, combining germicidal and oxidative properties of UV. Black-Right-Pointing-Pointer Coupled wavelengths have the most efficient bactericidal effect. Black-Right-Pointing-Pointer Coupling UV-A and UV-C leads to photooxidation of creatinine and phenol.

Light Converting Inorganic Phosphors for White Light-Emitting Diodes

OpenAIRE

Chen, Lei; Lin, Chun-Che; Yeh, Chiao-Wen; Liu, Ru-Shi

2010-01-01

White light-emitting diodes (WLEDs) have matched the emission efficiency of florescent lights and will rapidly spread as light source for homes and offices in the next 5 to 10 years. WLEDs provide a light element having a semiconductor light emitting layer (blue or near-ultraviolet (nUV) LEDs) and photoluminescence phosphors. These solid-state LED lamps, rather than organic light emitting diode (OLED) or polymer light-emitting diode (PLED), have a number of advantages over conventional incand...

Evaluating UV-C LED disinfection performance and investigating potential dual-wavelength synergy.

Science.gov (United States)

Beck, Sara E; Ryu, Hodon; Boczek, Laura A; Cashdollar, Jennifer L; Jeanis, Kaitlyn M; Rosenblum, James S; Lawal, Oliver R; Linden, Karl G

2017-02-01

A dual-wavelength UV-C LED unit, emitting at peaks of 260 nm, 280 nm, and the combination of 260|280 nm together was evaluated for its inactivation efficacy and energy efficiency at disinfecting Escherichia coli, MS2 coliphage, human adenovirus type 2 (HAdV2), and Bacillus pumilus spores, compared to conventional low-pressure and medium-pressure UV mercury vapor lamps. The dual-wavelength unit was also used to measure potential synergistic effects of multiple wavelengths on bacterial and viral inactivation and DNA and RNA damage. All five UV sources demonstrated similar inactivation of E. coli. For MS2, the 260 nm LED was most effective. For HAdV2 and B. pumilus, the MP UV lamp was most effective. When measuring electrical energy per order of reduction, the LP UV lamp was most efficient for inactivating E. coli and MS2; the LP UV and MP UV mercury lamps were equally efficient for HAdV2 and B. pumilus spores. Among the UV-C LEDs, there was no statistical difference in electrical efficiency for inactivating MS2, HAdV2, and B. pumilus spores. The 260 nm and 260|280 nm LEDs had a statistical energy advantage for E. coli inactivation. For UV-C LEDs to match the electrical efficiency per order of log reduction of conventional LP UV sources, they must reach efficiencies of 25-39% or be improved on by smart reactor design. No dual wavelength synergies were detected for bacterial and viral inactivation nor for DNA and RNA damage. Copyright © 2016 Elsevier Ltd. All rights reserved.

UV dichroic coatings on metallic reflectors

International Nuclear Information System (INIS)

Raghunath, C; Babu, N J; Chandran, K M

2008-01-01

The work presented here explains the design and deposition process of dichroic coating on metallic reflectors developed for UV curing systems. Special designs are adopted to achieve the spectral band and optimized to suit to the requirements. A mirror, which reflects the UV radiation (220 - 400 nm) and absorbs visible and infrared radiation (400 - 2000nm), is described in detail

UV dichroic coatings on metallic reflectors

Energy Technology Data Exchange (ETDEWEB)

Raghunath, C; Babu, N J; Chandran, K M [Hind High Vacuum Co. Pvt. Ltd. No.17, Phase 1, Peenya Industrial Area, Bangalore 560058 (India)

2008-05-01

The work presented here explains the design and deposition process of dichroic coating on metallic reflectors developed for UV curing systems. Special designs are adopted to achieve the spectral band and optimized to suit to the requirements. A mirror, which reflects the UV radiation (220 - 400 nm) and absorbs visible and infrared radiation (400 - 2000nm), is described in detail.

Efficient and thermally stable red luminescence from nano-sized phosphor of Gd6MoO12:Eu3+

International Nuclear Information System (INIS)

Qin, Lin; Wei, Donglei; Huang, Yanlin; Kim, Sun Il; Yu, Young Moon; Seo, Hyo Jin

2013-01-01

A novel red-emitting nano-phosphor of Eu 3+ -doped Gd 6 MoO 12 was successfully synthesized by the Pechini method. The crystalline phase was confirmed by X-ray powder diffraction analysis. The morphology of the nano-phosphor was analyzed by scanning electron microscopy, indicating a good crystallization with particles smaller than 500 nm. The luminescence properties such as photoluminescence spectra and decay curves were investigated. The phosphors can be efficiently excited by near-ultraviolet (near-UV) light and exhibit a bright red luminescence around 613 nm ascribed to the forced electric dipole transition 5 D 0 → 7 F 2 of Eu 3+ ions. The thermal stabilities were investigated from the temperature-dependent luminescence decay curves (lifetimes) and spectra intensities. The luminescence properties in relation to applications in white light-emitting diodes (W-LEDs) such as the absolute luminescence quantum efficiency, excitation wavelength, and color coordinates were discussed. The Gd 6 MoO 12 :Eu 3+ nano-phosphor is a promising red-emitting candidate for the fabrication of W-LEDs with near-UV chips

Permanent transparent color-warming glazes for dimmable and non-dimmable LED bulbs

Science.gov (United States)

Spanard, Jan-Marie A.

2014-02-01

Illuminant metameric failure is frequently experienced when viewing material samples under LED generated light vs. traditional incandescent light. LED light temperatures can be improved with phosphor coatings, but long-wave red light is still generally absent in LED "warm-white" light, resulting in metameric failure of orange-to-red objects. Drawing on techniques developed for the architectural restoration of stained glass, we find that transparent, heat-resistant, permanent, pigmented coatings can be applied to any glass, aluminum or plastic surface of an LED bulb, including the phosphor plate, dome or envelope, to produce warmer visible light than in current warm-light LED bulbs. These glazes can be applied in combination with existing technologies to better tune the LED emitted light or they may be used alone. These pigmented coatings include, but are not limited to, those made by suspending inorganic materials in potassium silicates or durable transparent pigmented resins. The pigmented resin glazes may be produced in either a clear gloss vehicle or an iridescent, light diffusing transparent base. Further, a graduated density of the tinted glazes on dimmable bulbs allow the light to change color as wattage is diminished. The glazes may be applied in the manufacturing of the bulb or marketed to current bulb owners as an after-market product to better tune the thousands of LED light bulbs currently in use.

A novel orange emissive phosphor SrWO4:Sm3+ for white light-emitting diodes

International Nuclear Information System (INIS)

Ju Zhenghua; Wei Ruiping; Ma Jingxin; Pang Chaoran; Liu Weisheng

2010-01-01

Research highlights: → A novel orange emissive phosphor SrWO 4 :Sm 3+ was firstly reported. → The optics properties of Sm 3+ -doped SrWO 4 phosphor were successfully discussed. → The temperature-dependent luminescence indicates the phosphor exhibits a small thermal-quenching property. → The phosphor is a potential candidate as orange-emitting component for white LED. - Abstract: A novel orange emissive phosphor, Sm 3+ -doped SrWO 4 , was synthesized by high temperature solid-state reaction in air atmosphere. The excitation spectra show that the phosphors can be efficiently excited by ultraviolet and near-ultraviolet light, the optimized concentration is 4 mol%. Three emission peaks locate at 562, 596 and 642 nm, corresponding to CIE chromaticity coordinates of (x = 0.54, y = 0.46), which indicates the orange light emitting. The decay curves are well fitted with triple-exponential decay models. The quantum yield of the Sr 0.96 Sm 0.04 WO 4 phosphor is about 70.65% under excitation of 377 nm. Furthermore, the temperature-dependent luminescence indicates the phosphor exhibits a small thermal-quenching property. So the phosphor is able to be applied to UV-LED chip-based white light-emitting diodes.

Synthesis and photoluminescence properties of Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} red phosphors for white LED applications

Energy Technology Data Exchange (ETDEWEB)

Annadurai, G.; Kennedy, S. Masilla Moses, E-mail: kennedysmm@ssn.edu.in

2016-01-15

Novel pellyite type Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} red emitting phosphors with different Eu{sup 3+} contents were synthesized by the solid state reaction method. The crystal structure, photoluminescence properties and concentration quenching of Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} phosphors were investigated. Powder X-ray diffraction measurements confirmed the structure of the samples. The photoluminescence emission (PL) and excitation (PLE) spectra were measured. The results showed that the dominant hypersensitive red emission peak of the phosphors Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} was located at 613 nm attributed to the Eu{sup 3+} transition ({sup 5}D{sub 0}→{sup 7}F{sub 2}) which could be effectively excited by 395 nm (near-UV). The latter band matched well with the emission from the near-UV LED chips. The intensity ratio of {sup 5}D{sub 0}→{sup 7}F{sub 2} to {sup 5}D{sub 0}→{sup 7}F{sub 1} transition showed slight variation with Eu{sup 3+} concentrations. The Eu{sup 3+} emission intensity was maximum for 9 mol%. The luminescence quantum efficiency was determined and also the decay profiles were obtained and analyzed. In addition, the Commission International del'Eclairage (CIE) chromaticity coordinates of Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:0.09Eu{sup 3+} phosphor were calculated to be 0.637 and 0.362. The experimental results demonstrated that the Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} red emitting phosphor is a potential candidate for white light emitting diodes (WLEDs) pumped by near-UV chip. - Highlights: • A novel Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} red phosphor was synthesized. • The samples yielded a dominant PL emission of Eu{sup 3+} at 613 nm. • Eu{sup 3+} concentration was optimized to be 9 mol% in Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17.} • CIE chromaticity coordinates were estimated from the emission spectrum.

Blue emitting KSCN:xCe phosphor for solid state lighting

Energy Technology Data Exchange (ETDEWEB)

Chikte, Devayani, E-mail: devi.awade@gmail.com [G.N. Khalsa College, Matunga, Mumbai 400019 (India); Omanwar, S.K. [Department of Physics, S.G.B. Amravati University, Amravati (India); Moharil, S.V. [Department of Physics, R.T.M. Nagpur University, Nagpur 440010 (India)

2014-01-15

The intense blue emitting phosphor KSCN:xCe (x=0.005, 0.01, 0.02, 0.04) is synthesized by a simple, time saving, economical method of re-crystallization through aqueous solution at 353 K. Photoluminescence measurements showed that the said phosphor exhibits emission with good intensity peaking at 450 nm corresponding to d→f transitions of Ce{sup 3+} ion. The excitation spectra monitored at 450 nm shows small peak at 282 nm and broad intense excitation band peaking at 350 nm. The latter lies in near ultraviolet (350–410 nm) emission of UV LED. The phosphor KSCN:0.02Ce{sup 3+} shows CIE 1931 color coordinates as (0.1484, 0.0602) whereas the commercial blue phosphor BAM:Eu{sup 2+} shows the color co-ordinates as (0.1417, 0.1072), respectively, indicating better color purity for KSCN: 0.02Ce{sup 3+} compared to the BAM:Eu{sup 2+} phosphor. The color coordinates of KSCN: 0.02Ce{sup 3+} phosphor (0.1484, 0.0602) are nearer to the color coordinate for blue color suggested by the color systems EBUPAL/SECAM, sRGB Blue as well as Adobe blue(0.15, 0.06). -- Highlights: • Novel phosphor KSCN:xCe prepared for the first time. • Method is simple, time saving, economical, easy to handle. • Intense, blue, Characteristic Ce{sup 3+} emission at 450 nm. • nUV excitation, suitable for solid state lighting.

Evaluation of UV-permeability and photo-oxidisability of organic ultraviolet radiation-absorbing coatings

Energy Technology Data Exchange (ETDEWEB)

Li, Neng; Chen, Yuhe, E-mail: yuhec@sina.com; Bao, Yongjie; Zhang, Zeqian; Wu, Zaixing; Chen, Zhangmin

2015-03-30

Highlights: • We investigate organic UV radiation-absorbing coatings for use on bamboo surfaces. • The size of glass exactly inserted into sample cell of UV-Vis spectrophotometer. • A model was made to predict UV absorption of coatings. • We examine carbonyl groups change of coatings after ageing. • Two formulations which could effectively protect coating were obtained. - Abstract: Enhancing the durability of the coatings used on bamboo products is essential for increasing their use in outdoor environments. In this study, we investigated organic UV radiation-absorbing coatings for use on bamboo surfaces. The degree of resistance of the coatings, which contained 2-(2-hydroxy-3-tert-butyl-5-methyl-phenyl)-5-chlorinated benzotriazole (BTZ-1), to UV radiation degradation was determined through spectroscopic analysis. The critical BTZ-1 loading amount was determined by analysing the spectroscopic data. Fourier transform infrared spectroscopy was used to elucidate the relationship between the degree of photooxidation of the coatings and their BTZ-1 concentration. The experimental results showed that the coatings provided a high degree of shielding from UV radiation. The critical loading amount was determined to be 1.82 ± 0.05 g BTZ-1/m{sup 2}. The coatings formed using the formulations that contained 3 and 5 wt% BTZ-1 exhibited the lowest degree of photooxidation after exposure to UV radiation.

Ca8Mg(SiO4)4Cl2:Ce3+, Tb3+: A potential single-phased phosphor for white-light-emitting diodes

International Nuclear Information System (INIS)

Zhu Ge; Wang Yuhua; Ci Zhipeng; Liu Bitao; Shi Yurong; Xin Shuangyu

2012-01-01

A single-phased white-light-emitting phosphor Ca 8 Mg(SiO 4 ) 4 Cl 2 :Ce 3+ , Tb 3+ (CMSC:Ce 3+ , Tb 3+ ) is synthesized by a high temperature solid-state reaction method, and its photoluminescence properties are investigated. The obtained phosphor exhibits a strong excitation band between 250 and 410 nm, matching well with the dominant emission band of a UV light-emitting-diode (LED) chip. Energy transfer from Ce 3+ to Tb 3+ ions has been investigated and demonstrated to be a resonant type via a dipole–dipole mechanism. The energy transfer efficiency as well as the critical distance is also estimated. Furthermore, the phosphors can generate light from yellow-green through white and eventually to blue by properly tuning the relative ratio of Ce 3+ to Tb 3+ ions grounded on the principle of energy transfer. The results show that this phosphor has potential applications as a single-phased phosphor for UV white-light LEDs. - Highlights: ► The luminescence properties of Ca 8 Mg(SiO 4 ) 4 Cl 2 :Ce 3+ , Tb 3+ were investigated for the first time. ► The strong absorption of phosphors matches well with the emission band of UV LED chips. ► The energy transfer from Ce 3+ to Tb 3+ in Ca 8 Mg(SiO 4 ) 4 Cl 2 was investigated in detail. ► The white light (CIE=(0.29, 0.34)) is generated by tuning the relative ratio of Ce 3+ to Tb 3+ .

Preparation and Characterization of Fluorinated Hydrophobic UV-Crosslinkable Thiol-Ene Polyurethane Coatings

Directory of Open Access Journals (Sweden)

Wenjing Xia

2017-08-01

Full Text Available The polyurethane prepolymer terminated with a double bond was synthesized using isophorone diisocyanate (IPDI, hydroxyl terminated polybutadiene (HTPB, 1,4-butanediol (BDO, and 2-hydroxyethyl acrylate (HEA. Then, a series of innovative UV-curable polyurethane coatings were prepared by blending ene-terminated polyurethane, fluoroacrylate monomer, and multifunctional thiol crosslinker upon UV exposure. The incorporation of fluoroacrylate monomer and multifunctional thiols into polyurethane coatings significantly enhanced the hydrophobic property, mechanical property, pencil hardness, and glossiness of the polyurethane coatings. This method of preparing UV crosslinkable, hydrophobic polyurethane coatings based on thiol-ene chemistry exhibited numerous advantages over other UV photocuring systems.

Effects of Green - Emitting Phosphor (La,Ce,TbPO_4:Ce:Tb on Luminous Flux and Color Quality of White LED Lamps

Directory of Open Access Journals (Sweden)

Nguyen Thi Phuong Thao

2017-01-01

Full Text Available In this paper, we present and analyze the influence of (La,Ce,TbPO_4:Ce:Tb green phosphor (LaTb toward the performance of the multi-chip white LED (MCW-LEDs lamps including color uniformity, lumen output, Color Rendering Index (CRI, and Color Quality Scale (CQS. By mixing the LaTb green phosphor and the YAG:Ce yellow phosphor compounding under condition of 7000 K MCW-LEDs, this new approach can produce a huge meaningful change in lumen output and the angular color distribution of MCW-LEDs. We also study the interaction between the concentration and size of the LaTb particles with output flux, color uniformity, CRI, and CQS. The obtained results demonstrate that the higher lumen output, the higher color uniformity enhancement could be attained by adding the LaTb particles with a size range around 6-8 µm and the concentration around 1.5% in phosphor layer. Meanwhile, the decrease of the color rendering value (CRI and the Color Quality Scale (CQS tend to be stable and insignificant. In other words, the obtained results provide a prospective method which plays an important role in the development of MCW-LED manufacturing technology.

Luminescent characteristics of UV excited Sr_0_._5Ca_0_._5TiO_3: Pr"3"+ reddish-orange phosphor

International Nuclear Information System (INIS)

Vidyadharan, Viji; Mohan P, Remya; Joseph, Cyriac; Unnikrishnan, N.V.; Biju, P.R.

2016-01-01

Pr"3"+ doped Sr_0_._5Ca_0_._5TiO_3 phosphors were synthesised by solid state reaction process. The structure, surface morphology and photoluminescence of the prepared phosphors were analysed using XRD, SEM and photoluminescence spectroscopy respectively. The XRD pattern confirmed orthorhombic perovskite structure of the Sr_0_._5Ca_0_._5TiO_3: x Pr"3"+ phosphor. Agglomeration of particles with irregular shapes is observed from the SEM images. The emission spectra of Sr_0_._5Ca_0_._5TiO_3: x Pr"3"+ phosphor shows the samples can be effectively excited with UV light at 336 nm and exhibit a strong reddish-orange emission at 611 nm. Concentration dependence of emission intensity shows concentration quenching effect on increasing Pr"3"+ concentration after x = 0.1 because of dipole–dipole interaction. Using Blasse's formula, critical distance for energy transfer was calculated. The CIE co-ordinates, CCT, colour purity and luminescence decay of the prepared phosphors were also calculated. These results offer the prepared phosphor as a suitable candidate for various photonic applications. - Highlights: • Sr_0_._5Ca_0_._5TiO_3: x Pr"3"+ perovskite structured phosphors were synthesized. • Under UV excitation, the PL spectra show strong reddish-orange emission. • The emission from "3P_J levels of Pr"3"+ were absent due to the presence of IVCT band. • Concentration quenching due to dipole–dipole interaction was observed. • For x = 0.1, sample shows a maximum emission intensity with 91.7% colour purity.

Influence of interconnection on the long-term reliability of UV LED packages

Science.gov (United States)

Nieland, S.; Mitrenga, D.; Karolewski, D.; Brodersen, O.; Ortlepp, T.

2017-02-01

High power LEDs have conquered the mass market in recent years. Besides the main development focus to achieve higher productivity in the field of visible semiconductor LED processing, the wavelength range is further enhanced by active research and development in the direction of UVA / UVB / UVC. UVB and UVC LEDs are new and promising due to their numerous advantages. UV LEDs emit in a near range of one single emission peak with a width (FWHM) below 15 nm compared to conventional mercury discharge lamps and xenon sources, which show broad spectrums with many emission peaks over a wide range of wavelengths. Furthermore, the UV LED size is in the range of a few hundred microns and offers a high potential of significant system miniaturization. Of course, LED efficiency, lifetime and output power have to be increased [1]. Lifetime limiting issues of UVB/UVC-LED are the very high thermal stress in the chip resulting from the higher forward voltages (6-10 V @ 350 mA), the lower external quantum efficiency, below 10 % (most of the power disappears as heat), and the thermal resistance Rth of conventional LED packages being not able to dissipate these large amounts of heat for spreading. Beside the circuit boards and submounts which should have maximum thermal conductivity, the dimension of contacts as well as the interconnection of UV LED to the submount/package determinates the resolvable amount of heat [2]. In the paper different innovative interconnection techniques for UVC-LED systems will be discussed focused on the optimization of thermal conductivity in consideration of the assembly costs. Results on thermal simulation for the optimal contact dimensions and interconnections will be given. In addition, these theoretical results will be compared with results on electrical characterization as well as IR investigations on real UV LED packages in order to give recommendations for optimal UV LED assembly.

Robust superhydrophobic tungsten oxide coatings with photochromism and UV durability properties

Energy Technology Data Exchange (ETDEWEB)

Jiang, Ting [Hubei Collaborative Innovation Centre for Advanced Organic Chemical Materials and Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei University, Wuhan, 430062 (China); State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou, 730000 (China); Guo, Zhiguang, E-mail: zguo@licp.cas.cn [Hubei Collaborative Innovation Centre for Advanced Organic Chemical Materials and Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei University, Wuhan, 430062 (China); State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou, 730000 (China)

2016-11-30

Highlights: • Superhydrophobic tungsten oxide (TO) coatings with a water contact angle (WCA) of 155° and rolling angle of 3.5° were developed. • The superhydrophobic coatings have excellent mechanical robustness and UV durability. • The superhydrophobic TO coatings show the reversible convert of photochromism. • The coating exhibited excellent self-cleaning behavior due to its high WCA and low rolling angle. - Abstract: Robust superhydrophobic tungsten oxide (TO) coatings with a water contact angle (WCA) of 155° were developed for photochromism via a facile and substrate-independent route. Importantly, after scatch test on both a single and two orthogonal direction, the TO coating still exhibited superhydrophobic behavior, indicating excellent mechanical robustness. It is worth mentioning that the superhydrophobic TO coatings showed the reversible convert of photochromism of WO{sub 3} induced by alternating UV and visible light irradiation. Besides that, the TO coating remained superhydrophobicity after UV irradiation for 36 h, showing excellent UV durability. In addition, the coating showed good resistance to acidic droplets. Moreover, it can also be applied on other substrates, such as copper mesh, steel, paper and fiber. The coating exhibited excellent self-cleaning behavior due to its high WCA and low rolling angle. Overall, this work is a promising approach to design and produce functional superhydrophobic coatings for various substrates.

Discovery of novel solid solution Ca3Si3-x O3+x N4-2x : Eu2+ phosphors: structural evolution and photoluminescence tuning.

Science.gov (United States)

Wang, Baochen; Liu, Yan-Gai; Huang, Zhaohui; Fang, Minghao; Wu, Xiaowen

2017-12-22

Discovery of novel phosphors is one of the main issues for improving the color rendering index (CRI) and correlated color temperature (CCT) of white light-emitting diodes (w-LEDs). This study mainly presents a systematic research on the synthesis, crystal structure variation and photoluminescence tuning of novel (oxy)nitride solid solution Ca 3 Si 3-x O 3+x N 4-2x : Eu 2+ phosphors. XRD refinements show that lattice distortion occurs when x value diverges the optimum one (x = 1). The lattice distortion causes a widening of emission spectrum and an increase of Stokes shift (ΔSS), which leads to a bigger thermal quenching. With decrease of x value, the emission spectrum shows an obvious red-shift from 505.2 to 540.8 nm, which is attributed to the crystal field splitting. The enhanced crystal field splitting also broadens the excitation spectrum, making it possible to serve as the phosphor for near ultraviolet (n-UV) LEDs. A 3-phosphor-conversion w-LED lamp was fabricated with the as-prepared phosphor, which exhibits high CRI (Ra = 85.29) and suitable CCT (4903.35 K). All these results indicate that the Ca 3 Si 3-x O 3+x N 4-2x : Eu 2+ phosphor can serve as the green phosphor for n-UV w-LEDs, with a tunable spectrum by controlling the crystal structure and morphology.

X-ray image converters utilizing rare earth phosphor mixtures

International Nuclear Information System (INIS)

Rabatin, J.G.

1982-01-01

In an X-ray screen comprising a transparent support with a photographic film on each side, each film has a coating of a phosphor mixture comprising polyhedral Gd 2 O 2 S:Tb of average size 6 to 20 μ and plate-like LnOX:Tm of average size 2 to 12 μ wherein Ln=La or Gd, X=Cl or Br and Tm is present from 0.05 to 1 mole %. The mixture gives improved resolution and reduces the problem of light crossing over the transparent support. According to whether blue sensitive or green sensitive film is used, the ratio of phosphors is varied. U.V. absorbing and light reflecting layers may be incorporated in the structure. (author)

Temperature dependence of Ce:YAG single-crystal phosphors for high-brightness white LEDs/LDs

Science.gov (United States)

Arjoca, Stelian; Víllora, Encarnación G.; Inomata, Daisuke; Aoki, Kazuo; Sugahara, Yoshiyuki; Shimamura, Kiyoshi

2015-05-01

The growth of Ce:Y3Al5O12(Ce:YAG) single-crystal phosphors (SCPs) by the Czochralski technique is analyzed in terms of segregation coefficient, solubility and absorption cross-section. The emission characteristics of these SCPs are investigated in a wide temperature range, from liquid He temperature up to 500 °C. The internal quantum efficiency of SCPs achieves its maximum at about 250 °C. Thermal quenching of SCPs at high temperature is attributed to the Mott-Seitz mechanism. In the case of ceramic powder phosphors, a continuous droop is observed with the temperature due to defect-related non-radiative recombination paths. It is shown that (Ce:YAG SCPs + blue LEDs/LDs) can cover a wide range of color temperatures 5500-7000 K, with color rendering indices around 70. In conclusion, it is shown that Ce:YAG SCPs are the most efficient and temperature stable converters to fabricate high-brightness white light sources with high-power blue LEDs and LDs.

Ultraviolet downconverting phosphor for use with silicon CCD imagers

Science.gov (United States)

Blouke, M. M.; Cowens, M. W.; Hall, J. E.; Westphal, J. A.; Christensen, A. B.

1980-01-01

The properties and application of a UV downconverting phosphor (coronene) to silicon charge coupled devices are discussed. Measurements of the absorption spectrum have been extended to below 1000 A, and preliminary results indicate the existence of useful response to at least 584 A. The average conversion efficiency of coronene was measured to be approximately 20% at 2537 A. Imagery at 3650 A using a backside illuminated 800 x 800 CCD coated with coronene is presented.

UV and X radiation effects on the stability of calcium halide phosphate phosphors. 2

International Nuclear Information System (INIS)

Tews, W.; Getter, R.; Kleemann, M.

1983-01-01

Sb(V) and Sb(III) concentrations in calcium halide phosphate phosphors have been investigated as a function of time of irradiation with near UV and X radiation. It was found that the reduction of both Sb(V) and Sb(III) to elemental Sb results in intensity losses. The reductions follow consecutive first-order kinetics and first-order kinetics, respectively

Li4SrCa(SiO4)2:Ce3+, a highly efficient near-UV and blue emitting orthosilicate phosphor

International Nuclear Information System (INIS)

Zhang, Jilin; Zhang, Weilu; Qiu, Zhongxian; Zhou, Wenli; Yu, Liping; Li, Zhiqiang; Lian, Shixun

2015-01-01

High quantum efficiency is a vital parameter of phosphors for practical application. An efficient near-UV and blue emitting phosphor Li 4 SrCa(SiO 4 ) 2 :Ce 3+ was synthesized by a traditional solid-state reaction, and luminescent properties were studied in detail. The Ce 3+ -activated phosphor can emit both a near-UV light centred at 345 nm and a blue light peaking at 420 nm when Ce 3+ occupies the Sr and Ca site, respectively. The internal quantum efficiency (IQE) of Li 4 SrCa(SiO 4 ) 2 :0.03Ce 3+ is as high as 97% under the excitation at 288 nm, while the external quantum efficiency (EQE) is 66%. The IQE and EQE values of Li 4 SrCa(SiO 4 ) 2 :0.03Ce 3+ under the excitation at 360 nm are 82% and 31%, respectively. - Highlights: • Phosphor Li 4 SrCa(SiO 4 ) 2 :Ce 3+ emits a near-UV (345 nm) and a blue light (420 nm). • Emission band at 345 nm originates from Ce 3+ on Sr site. • Emission band at 420 nm belongs to Ce 3+ on Ca site. • Internal quantum efficiency is 97% for Li 4 SrCa(SiO 4 ) 2 :0.03Ce 3+ excited at 288 nm

Synthesis and photoluminescence properties of LiSrPO{sub 4}:Eu{sup 2+} phosphor for solid state lighting

Energy Technology Data Exchange (ETDEWEB)

Game, D. N., E-mail: deorao.game@gmail.com [Deccan Education Society’s Technical Institute, Fergusson College Campus, Pune (India); Taide, S. T.; Khan, Z. S.; Omanwar, S. K. [Department of Physics, Sant Gadge Baba, Aravati University, Amravati (India); Ingale, N. B. [Prof. Ram Meghe Institute of Technology and Research, Badnera, Amravati (India)

2016-05-06

A novel method to prepare orthophosphate LiSrPO{sub 4}: Eu{sup 2+} phosphor for white light-emitting diodes (w-LEDs) is given in this paper. Phosphor was successfully synthesized by Pechini (citrate gel) method which is efficient than conventional high temperature solid state reaction. X-ray powder diffraction (XRD) analysis confirmed the single phase formation of LiSrPO{sub 4}:Eu{sup 2+} with monoclinic crystal structure. Luminescence results showed that the phosphor could be efficiently excited by near UV and exhibited bright blue emission at λ{sub em} = 420 nm corresponding to 5d– 4f transition of Eu{sup 2+}. The phosphor exhibits blue emission bands under 350 nm excitation. This mercury-free excitation is useful for solid state lighting and light-emitting diode (LED). Hence it could be useful for solid state lighting and light-emitting diode (LED) application.

Radiation polymerizable coating composition containing an unsaturated phosphoric ester

International Nuclear Information System (INIS)

Dickie, R.A.; Cassatta, J.C.

1976-01-01

A radiation polymerizable protective coating composition or paint consists essentially of a binder solution of: (1) between about 90 and about 10 parts of a saturated, thermoplastic vinyl polymer prepared from at least about 85 weight percent of monofunctional vinyl monomers; (2) between about 10 and about 90 parts of vinyl solvent monomers for the vinyl polymer, at least about 10 weight percent, preferably at least about 30 weight percent, of the solvent monomers being selected from the group consisting of divinyl monomers, trivinyl monomers, tetravinyl monomers and mixtures of these; and (3) between about 1.0 and about 15.0 parts per 100 parts of the total of the thermoplastic vinyl polymer and the vinyl solvent monomers of a triester of phosphoric acid bearing one or more sites of vinyl unsaturation. The composition exhibits excellent quality and good adhesion to a variety of substrates, in particular metals, including vapor deposited metals. Preferred articles bearing such a coating are prepared by applying a base coat to a substrate and curing the same; vapor depositing a coating of metal over the surface of the base coat; and applying to and curing on the surface of the deposited metal the radiation polymerizable topcoat, preferably with little or no pigment contained therein. 7 claims, no drawings

Nanopatterned yttrium aluminum garnet phosphor incorporated film for high-brightness GaN-based white light emitting diodes

International Nuclear Information System (INIS)

Cho, Joong-yeon; Park, Sang-Jun; Ahn, Jinho; Lee, Heon

2014-01-01

In this study, we fabricated high-brightness white light emitting diodes (LEDs) by developing a nanopatterned yttrium aluminum garnet (YAG) phosphor-incorporated film. White light can be obtained by mixing blue light from a GaN-based LED and yellow light of the YAG phosphor-incorporated film. If white light sources can be fabricated by exciting proper yellow phosphor using blue light, then these sources can be used instead of the conventional fluorescent lamps with a UV source, for backlighting of displays. In this work, a moth-eye structure was formed on the YAG phosphor-incorporated film by direct spin-on glass (SOG) printing. The moth-eye structures have been investigated to improve light transmittance in various optoelectronic devices, including photovoltaic solar cells, light emitting diodes, and displays, because of their anti-reflection property. Direct SOG printing, which is a simple, easy, and relatively inexpensive process, can be used to fabricate nanoscale structures. After direct SOG printing, the moth-eye structure with a diameter of 220 nm was formed uniformly on the YAG phosphor-incorporated film. As a result of moth-eye patterning on the YAG phosphor-incorporated film, the light output power of a white LED with a patterned YAG phosphor-incorporated film increased to up to 13% higher than that of a white LED with a non-patterned film. - Highlights: • GaN-based high-brightness white LED was prepared using patterned YAG phosphor-incorporated films. • Direct hydrogen silsesquioxane printing was used to form moth-eye patterns on the YAG films. • The electroluminescence intensity of the white LED was enhanced by up to 14.9%

Nanopatterned yttrium aluminum garnet phosphor incorporated film for high-brightness GaN-based white light emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Cho, Joong-yeon; Park, Sang-Jun [Department of Materials Science and Engineering, Korea University, Seoul 136-713 (Korea, Republic of); Ahn, Jinho, E-mail: jhahn@hanyang.ac.kr [Department of Material Science and Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Lee, Heon, E-mail: heonlee@korea.ac.kr [Department of Materials Science and Engineering, Korea University, Seoul 136-713 (Korea, Republic of)

2014-11-03

In this study, we fabricated high-brightness white light emitting diodes (LEDs) by developing a nanopatterned yttrium aluminum garnet (YAG) phosphor-incorporated film. White light can be obtained by mixing blue light from a GaN-based LED and yellow light of the YAG phosphor-incorporated film. If white light sources can be fabricated by exciting proper yellow phosphor using blue light, then these sources can be used instead of the conventional fluorescent lamps with a UV source, for backlighting of displays. In this work, a moth-eye structure was formed on the YAG phosphor-incorporated film by direct spin-on glass (SOG) printing. The moth-eye structures have been investigated to improve light transmittance in various optoelectronic devices, including photovoltaic solar cells, light emitting diodes, and displays, because of their anti-reflection property. Direct SOG printing, which is a simple, easy, and relatively inexpensive process, can be used to fabricate nanoscale structures. After direct SOG printing, the moth-eye structure with a diameter of 220 nm was formed uniformly on the YAG phosphor-incorporated film. As a result of moth-eye patterning on the YAG phosphor-incorporated film, the light output power of a white LED with a patterned YAG phosphor-incorporated film increased to up to 13% higher than that of a white LED with a non-patterned film. - Highlights: • GaN-based high-brightness white LED was prepared using patterned YAG phosphor-incorporated films. • Direct hydrogen silsesquioxane printing was used to form moth-eye patterns on the YAG films. • The electroluminescence intensity of the white LED was enhanced by up to 14.9%.

Tunable luminescence and energy transfer properties of KSr{sub 4}(BO{sub 3}){sub 3}:Dy{sup 3+}, Eu{sup 3+} phosphors for near-UV warm-white LEDs

Energy Technology Data Exchange (ETDEWEB)

Leng, Zhihua; Li, Linlin; Liu, Yali; Zhang, Nannan; Gan, Shucai, E-mail: gansc@jlu.edu.cn

2016-05-15

Dy{sup 3+} and Eu{sup 3+} codoped KSr{sub 4}(BO{sub 3}){sub 3} phosphors were successfully synthesized by solid-state reaction process. Under near-ultraviolet (near-UV) excitation, individual Dy{sup 3+} or Eu{sup 3+} ion activated sample exhibits characteristic emissions in their respective regions. In KSr{sub 4}(BO{sub 3}){sub 3}:Dy{sup 3+}, xEu{sup 3+} phosphors, the energy transfer from Dy{sup 3+} to Eu{sup 3+} was revealed to be resonant type by dipole–dipole mechanism. And the critical distance R{sub Dy–Eu} was calculated to be 13.95 Å. The energy transfer efficiency of KSr{sub 4}(BO{sub 3}){sub 3}:Dy{sup 3+}, xEu{sup 3+} reached about 20% when the concentration of Eu{sup 3+} was 0.035. Moreover, the emitting colors of Dy{sup 3+} and Eu{sup 3+} codoped samples can be adjusted from the edge of white area to warm white via tuning the activator (Eu{sup 3+}) doped concentration. More significantly, the chromaticity coordinates (0.334, 0.351) of KSr{sub 4}(BO{sub 3}){sub 3}:0.005Dy{sup 3+}, 0.015Eu{sup 3+} sample are extremely adjacent to standard white light (0.33, 0.33). The quantum efficiency of the KSr{sub 4}(BO{sub 3}){sub 3}:0.005Dy{sup 3+}, 0.015Eu{sup 3+} phosphor with 389 nm excitation is found to be 42%, demonstrating that the obtained single-component white-emitting phosphor exhibits potential applications for solid state lighting.

Scaling Up: Kilolumen Solid-State Lighting Exceeding 100 LPW via Remote Phosphor

Energy Technology Data Exchange (ETDEWEB)

Waqidi Falicoff

2008-09-15

This thirty-month project was successful in attaining its ambitious objectives of demonstrating a radically novel 'remote-phosphor' LED light source that can out-perform conventional conformal coated phosphor LED sources. Numerous technical challenges were met with innovative techniques and optical configurations. This product development program for a new generation of solid-state light sources has attained unprecedented luminosity (over 1 kilo-lumen) and efficacy (based on the criterion lumens per 100mw radiant blue). LPI has successfully demonstrated its proprietary technology for optical synthesis of large uniform sources out of the light output of an array of separated LEDs. Numerous multiple blue LEDs illuminate single a phosphor patch. By separating the LEDs from the phosphor, the phosphor and LEDs operate cooler and with higher efficiency over a wide range of operating conditions (from startup to steady state). Other benefits of the system include: better source uniformity, more types of phosphor can be used (chemical interaction and high temperatures are no longer an issue), and the phosphor can be made up from a pre-manufactured sheet (thereby lowering cost and complexity of phosphor deposition). Several laboratory prototypes were built and operated at the expected high performance level. The project fully explored two types of remote phosphor system: transmissive and reflective. The first was found to be well suited for a replacement for A19 type incandescent bulbs, as it was able to replicate the beam pattern of a traditional filament bulb. The second type has the advantages that it is pre-collimate source that has an adjustable color temperature. The project was divided in two phases: Phase I explored a transmissive design and Phase II of the project developed reflective architectures. Additionally, in Phase II the design of a spherical emitting transmissive remote phosphor bulb was developed that is suitable for replacement of A19 and

A novel orange-red emitting NaCaVO{sub 4}:Sm{sup 3+} phosphor for solid state lighting

Energy Technology Data Exchange (ETDEWEB)

Biswas, Pankaj, E-mail: pankaj79biswas@gmail.com; Kumar, Vinay, E-mail: vinaykdhiman@yahoo.com [School of Physics, Shri Mata Vaishno Devi University, Katra-182320 J& K (India); Ntwaeaborwa, O. M.; Swart, H. C. [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA9300 (South Africa)

2016-05-06

The samarium doped NaCaVO{sub 4} phosphor was synthesized by the combustion method. The X-ray powder diffraction (XRD) analysis confirmed that the phosphor powder crystallized as orthorhombic structure belonging to space group Cmcm. From Williamson-Hall analysis the grain size and microstrain in the powder was estimated. The Fourier- transform infrared (FT-IR) studies further validated the formation of vanadate phase of the phosphor. Photoluminescence (PL) study revealed that the phosphor could be efficiently excited by UV-VIS from 200 nm to 500 nm. The 565 nm, 602 nm, 648 nm and 713 nm emissions were ascribed to {sup 4}G{sub 5/2} to {sup 6}H{sub J} (J = 5/2, 7/2, 9/2 and 11/2) transitions of the Sm{sup 3+} ion. The present material may be explored as a novel phosphor to be excited by UV light emitting diodes (LEDs) chips for solid-state lighting and display applications.

Investigation of uniformity field generated from freeform lens with UV LED exposure system

Science.gov (United States)

Ciou, F. Y.; Chen, Y. C.; Pan, C. T.; Lin, P. H.; Lin, P. H.; Hsu, F. T.

2015-03-01

In the exposure process, the intensity and uniformity of light in the exposure area directly influenced the precision of products. UV-LED (Ultraviolet Light-Emitting Diode) exposure system was established to reduce the radiation leakage and increase the energy efficiency for energy saving. It is a trend that conventional mercury lamp could be replaced with UV-LED exposure system. This study was based on the law of conservation of energy and law of refraction of optical field distributing on the target plane. With these, a freeform lens with uniform light field of main exposure area could be designed. The light outside the exposure area could be concentrated into the area to improve the intensity of light. The refraction index and UV transmittance of Polydimethylsiloxane (PDMS) is 1.43 at 385 nm wavelength and 85-90%, respectively. The PDMS was used to fabricate the optics lens for UV-LEDs. The average illumination and the uniformity could be obtained by increasing the number of UV-LEDs and the spacing of different arrangement modes. After exposure process with PDMS lens, about 5% inaccuracy was obtained. Comparing to 10% inaccuracy of general exposure system, it shows that it is available to replace conventional exposure lamp with using UV-LEDs.

UV-visible light photocatalytic properties of NaYF4:(Gd, Si)/TiO2 composites

Science.gov (United States)

Mavengere, Shielah; Kim, Jung-Sik

2018-06-01

In this study, a new novel composite photocatalyst of NaYF4:(Gd, Si)/TiO2 phosphor has been synthesized by two step method of solution combustion and sol-gel. The photocatalyst powders were characterized by X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), UV-vis spectroscopy and photoluminescence (PL) spectroscopy. Raman spectroscopy confirmed the anatase TiO2 phase which remarkably increased with existence of yttrium silicate compounds between 800 cm-1 and 900 cm-1. Double-addition of Gd3+-Si4+ ions in NaYF4 host introduced sub-energy band levels with intense absorption in the ultraviolet (UV) light region. Photocatalytic activity was examined by exposing methylene blue (MB) solutions mixed with photocatalyst powders to 254 nm UV-C fluorescent lamp and 200 W visible lights. The UV and visible photocatalytic reactivity of the NaYF4:(Gd, 1% Si)/TiO2 phosphor composites showed enhanced MB degradation efficiency. The coating of NaYF4:(Gd, 1% Si) phosphor with TiO2 nanoparticles creates energy band bending at the phosphor/TiO2 interfaces. Thus, these composites exhibited enhanced absorption of UV/visible light and the separation of electron and hole pairs for efficient photocatalysis.

Assessing the use of Low Voltage UV-light Emitting Miniature LEDs for Marine Biofouling Control

Science.gov (United States)

2016-07-01

of that required to drive traditional UV mercury lamps . Secondly, given their small size and relatively low cost, UV LEDs provide ease of maintenance...UNCLASSIFIED UNCLASSIFIED Assessing the use of Low Voltage UV -light Emitting Miniature LEDs for Marine Biofouling Control Richard...settling organisms. The introduction of miniature UV light emitting diodes ( LEDs ) as a light source enables them to be embedded into thin, flexible

Photoluminescence properties of Eu(3+)/ Sm(3+) activated CaZr4(PO4)6 phosphors.

Science.gov (United States)

Nair, Govind B; Dhoble, S J

2016-09-01

Solid state reaction method was employed for the synthesis of a series of CaZr4(PO4)6: Eu(3+)/Sm(3+) phosphors. The red-emitting CaZr4(PO4)6:Eu(3+) phosphors can be efficiently excited at 396 nm and thereby, exhibit a strong red luminescence predominantly corresponding to the electric dipole transition at 615 nm. Under 405 nm excitation, CaZr4(PO4)6:Sm(3+) phosphors display orange emission with color temperatures approximately around 2200 K. The acquired results reveal that CaZr4(PO4)6: RE(3+) (RE = Eu, Sm) phosphors could be potential candidates for red and orange emitting phosphor, respectively, for UV/blue-pump LEDs.

Luminescence and luminescence quenching of highly efficient Y2Mo4O15:Eu(3+) phosphors and ceramics.

Science.gov (United States)

Janulevicius, Matas; Marmokas, Paulius; Misevicius, Martynas; Grigorjevaite, Julija; Mikoliunaite, Lina; Sakirzanovas, Simas; Katelnikovas, Arturas

2016-05-16

A good LED phosphor must possess strong enough absorption, high quantum yields, colour purity, and quenching temperatures. Our synthesized Y2Mo4O15:Eu(3+) phosphors possess all of these properties. Excitation of these materials with near-UV or blue radiation yields bright red emission and the colour coordinates are relatively stable upon temperature increase. Furthermore, samples doped with 50% Eu(3+) showed quantum yields up to 85%, what is suitable for commercial application. Temperature dependent emission spectra revealed that heavily Eu(3+) doped phosphors possess stable emission up to 400 K and lose half of the efficiency only at 515 K. In addition, ceramic disks of Y2Mo4O15:75%Eu(3+) phosphor with thickness of 0.71 and 0.98 mm were prepared and it turned out that they efficiently convert radiation of 375 and 400 nm LEDs to the red light, whereas combination with 455 nm LED yields purple colour.

Luminescence and luminescence quenching of highly efficient Y2Mo4O15:Eu3+ phosphors and ceramics

Science.gov (United States)

Janulevicius, Matas; Marmokas, Paulius; Misevicius, Martynas; Grigorjevaite, Julija; Mikoliunaite, Lina; Sakirzanovas, Simas; Katelnikovas, Arturas

2016-01-01

A good LED phosphor must possess strong enough absorption, high quantum yields, colour purity, and quenching temperatures. Our synthesized Y2Mo4O15:Eu3+ phosphors possess all of these properties. Excitation of these materials with near-UV or blue radiation yields bright red emission and the colour coordinates are relatively stable upon temperature increase. Furthermore, samples doped with 50% Eu3+ showed quantum yields up to 85%, what is suitable for commercial application. Temperature dependent emission spectra revealed that heavily Eu3+ doped phosphors possess stable emission up to 400 K and lose half of the efficiency only at 515 K. In addition, ceramic disks of Y2Mo4O15:75%Eu3+ phosphor with thickness of 0.71 and 0.98 mm were prepared and it turned out that they efficiently convert radiation of 375 and 400 nm LEDs to the red light, whereas combination with 455 nm LED yields purple colour. PMID:27180941

Impact of watering with UV-LED-treated wastewater on microbial and physico-chemical parameters of soil.

Science.gov (United States)

Chevremont, A-C; Boudenne, J-L; Coulomb, B; Farnet, A-M

2013-04-15

Advanced oxidation processes based on UV radiations have been shown to be a promising wastewater disinfection technology. The UV-LED system involves innovative materials and could be an advantageous alternative to mercury-vapor lamps. The use of the UV-LED system results in good water quality meeting the legislative requirements relating to wastewater reuse for irrigation. The aim of this study was to investigate the impact of watering with UV-LED treated wastewaters (UV-LED WW) on soil parameters. Solid-state ¹³C NMR shows that watering with UV-LED WW do not change the chemical composition of soil organic matter compared to soil watered with potable water. Regarding microbiological parameters, laccase, cellulase, protease and urease activities increase in soils watered with UV-LED WW which means that organic matter brought by the effluent is actively degraded by soil microorganisms. The functional diversity of soil microorganisms is not affected by watering with UV-LED WW when it is altered by 4 and 8 months of watering with wastewater (WW). After 12 months, functional diversity is similar regardless of the water used for watering. The persistence of faecal indicator bacteria (coliform and enterococci) was also determined and watering with UV-LED WW does not increase their number nor their diversity unlike soils irrigated with activated sludge wastewater. The study of watering-soil microcosms with UV-LED WW indicates that this system seems to be a promising alternative to the UV-lamp-treated wastewaters. Copyright © 2013 Elsevier Ltd. All rights reserved.

Synthesis and photoluminescence properties of Eu{sup 3+}, Sm{sup 3+} and Pr{sup 3+} doped Ca{sub 2}ZnWO{sub 6} phosphors for phosphor converted LED

Energy Technology Data Exchange (ETDEWEB)

Dabre, K.V. [Department of Physics, Arts, Commerce and Science College, Koradi, Nagpur-441111, Maharashtra (India); Dhoble, S.J., E-mail: sjdhoble@rediffmail.com [Department of Physics, R.T.M. Nagpur University, Nagpur-440033, Maharashtra (India)

2014-06-01

In this work, we report on the synthesis and photoluminescence (PL) properties of rare earth (Eu{sup 3+}, Sm{sup 3+} and Pr{sup 3+}) doped double perovskite tungstate Ca{sub 2}ZnWO{sub 6} phosphor. The phosphors were synthesized by two step modified solid state method. Phase purity and formation of phosphor were confirmed by XRD technique. PL spectra of Eu{sup 3+}, Sm{sup 3+} and Pr{sup 3+} doped phosphor show intense emission peaks in red region at 615, 604 and 650 nm respectively, upon the visible excitation of 466 nm (Eu{sup 3+}), 410 nm (Sm{sup 3+}) and 491 nm (Pr{sup 3+}). The CIE coordinates of the phosphors are in the yellow (Sm{sup 3+} doped sample) and orange (Eu{sup 3+} and Pr{sup 3+} doped sample) regions near the edge of color space which confirms their applicability in LEDs. -- Highlights: •Eu{sup 3+}, Sm{sup 3+} and Pr{sup 3+} doped and undoped samples of Ca{sub 2}ZnWO{sub 6} phosphor synthesized by Solid state method. •The phosphors have intense excitation in violet and blue region of visible spectrum. •Phosphors show intense emission peaks in red region. •CIE coordinates of phosphors are lie in yellow (Sm{sup 3+} doped phosphor) and orange (Eu{sup 3+} and Pr{sup 3+} doped phosphor) region near to edge of color space.

Luminescence in Eu2+ and Ce3+ doped SrCaP2O7 phosphors

Directory of Open Access Journals (Sweden)

K.N. Shinde

Full Text Available Eu2+ and Ce3+ doped SrCaP2O7 has been achieved by modified solid state diffusion in reducing atmosphere. The prepared phosphor powders have been identified by their characteristic X-ray diffraction patterns. The mixed phases of α-Sr2P2O7 type with orthorhombic and α-Ca2P2O7 type with monoclinic form were investigated. Its excitation wavelength ranging from 250 to 430 nm fits well with the characteristic emission of UV light-emitting diode (LED. The excitation and emission spectra indicate that these phosphors can be effectively excited by the near-UV light, and emits blue (visible range due to 4f7 → 4f65d1 transition of Eu2+ particularly, SrCaP2O7: Eu2+ whereas, photoluminescence excitation spectrum measurements of Ce3+ activated SrCaP2O7 shows that the phosphor can be efficiently excited by UV–Vis light from 280 to 310 nm to realize emission in the near visible range due to the 5d–4f transition of Ce3+ ions which is applicable for scintillation purpose. The impacts of doping of divalent europium and trivalent cerium on photoluminescence properties on SrCaP2O7 pyrophosphate phosphors were investigated and I propose a feasible interpretation. Keywords: Phosphor, Luminescence, XRD, LED, FTIR

UV protective zinc oxide coating for biaxially oriented polypropylene packaging film by atomic layer deposition

Energy Technology Data Exchange (ETDEWEB)

Lahtinen, Kimmo, E-mail: kimmo.lahtinen@lut.fi [ASTRaL, Lappeenranta University of Technology, Sammonkatu 12, FI-50130 Mikkeli (Finland); Kääriäinen, Tommi, E-mail: tommi.kaariainen@colorado.edu [ASTRaL, Lappeenranta University of Technology, Sammonkatu 12, FI-50130 Mikkeli (Finland); Johansson, Petri, E-mail: petri.johansson@tut.fi [Paper Converting and Packaging Technology, Tampere University of Technology, P.O.Box 589, FI-33101 Tampere (Finland); Kotkamo, Sami, E-mail: sami.kotkamo@tut.fi [Paper Converting and Packaging Technology, Tampere University of Technology, P.O.Box 589, FI-33101 Tampere (Finland); Maydannik, Philipp, E-mail: philipp.maydannik@lut.fi [ASTRaL, Lappeenranta University of Technology, Sammonkatu 12, FI-50130 Mikkeli (Finland); Seppänen, Tarja, E-mail: tarja.seppanen@lut.fi [ASTRaL, Lappeenranta University of Technology, Sammonkatu 12, FI-50130 Mikkeli (Finland); Kuusipalo, Jurkka, E-mail: jurkka.kuusipalo@tut.fi [Paper Converting and Packaging Technology, Tampere University of Technology, P.O.Box 589, FI-33101 Tampere (Finland); Cameron, David C., E-mail: david.cameron@miktech.fi [ASTRaL, Lappeenranta University of Technology, Sammonkatu 12, FI-50130 Mikkeli (Finland)

2014-11-03

Biaxially oriented polypropylene (BOPP) packaging film was coated with zinc oxide (ZnO) coatings by atomic layer deposition (ALD) in order to protect the film from UV degradation. The coatings were made at a process temperature of 100 °C using diethylzinc and water as zinc and oxygen precursors, respectively. The UV protective properties of the coatings were tested by using UV–VIS and infrared spectrometry, differential scanning calorimetry (DSC) and a mechanical strength tester, which characterised the tensile and elastic properties of the film. The results obtained with 36 and 67 nm ZnO coatings showed that the ZnO UV protective layer is able to provide a significant decrease in photodegradation of the BOPP film under UV exposure. While the uncoated BOPP film suffered a complete degradation after a 4-week UV exposure, the 67 nm ZnO coated BOPP film was able to preserve half of its original tensile strength and 1/3 of its elongation at break after a 6-week exposure period. The infrared analysis and DSC measurements further proved the UV protection of the ZnO coatings. The results show that a nanometre scale ZnO coating deposited by ALD is a promising option when a transparent UV protection layer is sought for polymer substrates. - Highlights: • Atomic layer deposited zinc oxide coatings were used as UV protection layers. • Biaxially oriented polypropylene (BOPP) film was well protected against UV light. • Formation of UV degradation products in BOPP was significantly reduced. • Mechanical properties of the UV exposed BOPP film were significantly improved.

UV induced photoluminescence and thermally stimulated luminescence of ThO{sub 2}:Tb{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Godbole, S.V.; Nagpal, J.S.; Page, A.G. E-mail: agpage@magnum.barc.ernet.in

2000-08-15

Thorium oxide doped with trivalent terbium ions offers itself as a novel phosphor with its photo- and thermally-stimulated luminescence (PL and TSL) characteristics showing a marked change on sustained exposure to 254 and 365 nm ultraviolet (UV) radiation. The reduction in luminescence intensity of Tb{sup 3+} ions, on irradiation with 254 nm photons and subsequent restoration on exposure to 365 nm, has been correlated with the complimentary behaviour in UV-induced TSL. These changes are, in turn, ascribed to inter-configurational (f-d) transitions and e-h formation and recombination processes. UV radiation induced TSL output increases linearly with incident UV radiant energy at a constant radiation flux; however, for a fixed exposure, TSL output increases with increase in radiant flux.

Analysis of Photosynthetic Characteristics and UV-B Absorbing Compounds in Mung Bean Using UV-B and Red LED Radiation

Directory of Open Access Journals (Sweden)

Fang-Min Li

2014-01-01

Full Text Available Mung bean has been reported to have antioxidant, antidiabetic, anti-inflammatory, and antitumor activities. Various factors have important effects on the types and contents of plant chemical components. In order to study quality of mung bean from different light sources, mung bean seedlings were exposed to red light-emitting diodes (LEDs and ultraviolet-B (UV-B. Changes in the growth parameters, photosynthetic characteristics, the concentrations of chlorophyll a and chlorophyll b and the content of UV-B absorbing compounds were measured. The results showed that photosynthetic characteristics and chlorophyll a and chlorophyll b concentrations were enhanced by red LEDs. The concentrations of UV-B absorbing compounds were enhanced by UV-B on the 20th day, while photosynthetic characteristics, plant length, and the concentrations of chlorophyll a and chlorophyll b were reduced by UV-B on the 40th day; at the same time the values of the stem diameter, plant fresh weight, dry weight, and the concentrations of UV-B absorbing compounds were enhanced. It is suggested that red LEDs promote the elongation of plant root growth and photosynthetic characteristics, while UV-B promotes horizontal growth of stems and the synthesis of UV-B absorbing compounds.

Inactivation kinetics and efficiencies of UV-LEDs against Pseudomonas aeruginosa, Legionella pneumophila, and surrogate microorganisms.

Science.gov (United States)

Rattanakul, Surapong; Oguma, Kumiko

2018-03-01

To demonstrate the effectiveness of UV light-emitting diodes (UV-LEDs) to disinfect water, UV-LEDs at peak emission wavelengths of 265, 280, and 300 nm were adopted to inactivate pathogenic species, including Pseudomonas aeruginosa and Legionella pneumophila, and surrogate species, including Escherichia coli, Bacillus subtilis spores, and bacteriophage Qβ in water, compared to conventional low-pressure UV lamp emitting at 254 nm. The inactivation profiles of each species showed either a linear or sigmoidal survival curve, which both fit well with the Geeraerd's model. Based on the inactivation rate constant, the 265-nm UV-LED showed most effective fluence, except for with E. coli which showed similar inactivation rates at 265 and 254 nm. Electrical energy consumption required for 3-log 10 inactivation (E E,3 ) was lowest for the 280-nm UV-LED for all microbial species tested. Taken together, the findings of this study determined the inactivation profiles and kinetics of both pathogenic bacteria and surrogate species under UV-LED exposure at different wavelengths. We also demonstrated that not only inactivation rate constants, but also energy efficiency should be considered when selecting an emission wavelength for UV-LEDs. Copyright © 2017 Elsevier Ltd. All rights reserved.

Recent developments in white light emitting diodes

Science.gov (United States)

Lohe, P. P.; Nandanwar, D. V.; Belsare, P. D.; Moharil, S. V.

2018-05-01

In the recent years solid state lighting based on LEDs has revolutionized lighting technology. LEDs have many advantages over the conventional lighting based on fluorescent and incandescent lamps such as mercury free, high conversion efficiency of electrical energy into light, long lifetime reliability and ability to use with many types of devices. LEDs have emerged as a new potentially revolutionary technology that could save up to half of energy used for lighting applications. White LEDs would be the most important light source in the future, so much so that this aspect had been highlighted by the Nobel committee during the award of 2014 Nobel Prize for Physics. Recent advancement in the fabrication of GaN chip capable of emitting in blue and near UV region paved way for fabrication of white LED lamps. Mainly there are two approaches used for preparing white emitting solid state lamp. In the first approach blue light (λ=450 nm) emitted from the InGaN LED chip is partially absorbed by the YAG:Ce3+ phosphor coated on it and re-emitted as yellow fluorescence. A white light can be generated by the combination of blue + yellow emission bands. These lamps are already available. But they are suffering from major drawback that their Colour Rendering Index (CRI) is low. In the second approach, white LEDs are made by coating near ultraviolet emitting (360 to 410nm) LED with a mixture of high efficiency red, green and blue emitting phosphors, analogous to the fluorescent lamp. This method yields lamps with better color rendition. Addition of a yellow emitting phosphor improves CRI further. However conversion efficiency is compromised to some extent. Further the cost of near UV emitting chip is very high compared to blue emitting chips. Thus cost and light output wise, near UV chips are much inferior to blue chips. Recently some rare earth activated oxynitrides, silicates, fluorides have emerged as an important family of luminescent materials for white LED application

Structural, spectroscopic and photoluminescence studies of LiEu(WO4)2-x (MoO4) x as a near-UV convertible phosphor

International Nuclear Information System (INIS)

Chiu, C.-H.; Wang, M.-F.; Lee, C.-S.; Chen, T.-M.

2007-01-01

A series of lithium europium double tungsto-molybdate phosphors LiEu(WO 4 ) 2- x (MoO 4 ) x (x=0, 0.4, 0.8, 1.2, 1.6, 2.0) have been synthesized by solid-state reactions and their crystal structure, optical and luminescent properties were studied. As the molybdate content increases, the intensity of the 5 D 0 →7 F 2 emission of Eu 3+ activated at wavelength of 396 nm was found to increase and reach a maximum when the relative ratio of Mo/W is 2:0. These changes were found to be accompanied with the changes in the spectral feature, which can be attributed to the crystal field splitting of the 5 D 0 →7 F 2 transition. As the molybdate content increases the emission intensity of the 615 nm peak also increases. The intense red-emission of the tungstomolybdate phosphors under near-UV excitation suggests them to be potential candidate for white light generation by using near-UV LEDs. In this study the effect of chemical compositions and crystal structure on the photoluminescent properties of LiEu(WO 4 ) 2- x (MoO 4 ) x is investigated and discussed. - Graphical abstract: As shown by the PL spectra of LiEu(WO 4 ) 2- x (MoO 4 ) x (x=0, 0.4, 0.8, 1.2, 1.6, 2.0) under 394 nm near-UV excitation, the intensity of 5 D 0 →7 F 2 transition was found to increase with the increasing x and the I-λ curve reaches a maximum when the relative ratio of Mo/W is 2:0

Double perovskite Ca2GdNbO6:Mn4+ deep red phosphor: Potential application for warm W-LEDs

Science.gov (United States)

Lu, Zuizhi; Huang, Tianjiao; Deng, Ruopeng; Wang, Huan; Wen, Lingling; Huang, Meixin; Zhou, Liya; Yao, Chunying

2018-05-01

A novel Mn4+-doped Ca2GdNbO6 (CGN) phosphor was prepared by high-temperature solid-state reaction. The crystal structure was investigated by X-ray diffraction patterns and unit cell structure. Mn4+ replaced the location of Nb5+ in the CGN lattice, and the value of energy gap (Egap) decreased from 2.16 eV to 1.13 eV, indicating that Mn4+ ions play a great influence on the absorption of CGN hosts. The broad excitation band from 250 nm to 550 nm matches well with commercial near-UV light emitting diodes, and the emission peak centered at 680 nm is due to 2E→4A2g transition in Mn4+ ions. The CIE chromaticity coordinates (0.698, 0.303) of CGN:Mn4+ phosphor was close to standard red color coordinates (0.666, 0.333). These investigations demonstrate CGN:Mn4+ phosphor as an efficient red phosphor for potential applications.

Single-phased white-light-emitting Sr3NaLa(PO4)3F: Eu2+,Mn2+ phosphor via energy transfer

International Nuclear Information System (INIS)

Shanshan, Hu; Wanjun, Tang

2014-01-01

Single-phased white-light-emitting Sr 3 NaLa(PO 4 ) 3 F:Eu 2+ ,Mn 2+ phosphor is synthesized via the combustion-assisted synthesis technique. Upon excitation of 344 nm ultraviolet (UV) light, two intense broad bands have clearly been obtained due to the allowed 5d–4f transition of Eu 2+ and the forbidden 4 T 1 − 6 A 1 transition of Mn 2+ , respectively. As a result of fine-tuning of the emission composition of the Eu 2+ and Mn 2+ ions, white-light emission can be realized by combining the emission of Eu 2+ and Mn 2+ in a single host lattice under UV light excitation. The obtained phosphor exhibits a strong excitation band between 250 and 420 nm, matching well with the dominant emission band of a UV light-emitting-diode (LED) chip, which could be a promising candidate for UV-converting white-light-emitting diodes (LEDs). -- Highlights: • Single-phased Sr 3 NaLa(PO 4 ) 3 F:Eu 2+ ,Mn 2+ phosphors are synthesized. • Sr 3 NaLa(PO 4 ) 3 F:Eu 2+ ,Mn 2+ shows a blue emission band and a yellow emission band. • White-emitting can be obtained by tuning the compositions of the Eu 2+ and Mn 2+

Study on luminescence and thermal stability of blue-emitting Sr_5(PO_4)_3F: Eu"2"+phosphor for application in InGaN-based LEDs

International Nuclear Information System (INIS)

Liu, Jie; Zhang, Zhi-Ming; Wu, Zhan-Chao; Wang, Fang-Fang; Li, Zhen-Jiang

2017-01-01

Highlights: • A blue phosphor Sr_5(PO_4)_3F: Eu"2"+ was prepared at low temperature of 800 °C. • The broad excitation band of the phosphor matches well with NUV LED chips. • The phosphor shows high color purity and good color stability. • A bright blue-emitting LED was fabricated with this phosphor on an InGaN chip. - Abstract: A series of blue-emitting phosphors Sr_5(PO_4)_3F: Eu"2"+ were synthesized by traditional high temperature solid-state reaction method. The micro-morphology and photoluminescence properties of the phosphors were investigated. The Sr_5(PO_4)_3F: Eu"2"+ phosphors exhibit broad excitation spectra ranging from 250 to 420 nm, and an intense asymmetric blue emission band peaking at 435 nm. Two different Eu"2"+ emission centers in Sr_5(PO_4)_3F: Eu"2"+ phosphors were confirmed via their fluorescence properties. The concentration quenching mechanism, fluorescence lifetime and thermal stability of Sr_5(PO_4)_3F: Eu"2"+ phosphors were studied in detail. The thermal stability can be improved obviously by anion substitution. The CIE chromaticity coordinates of Sr_5(PO_4)_3F: Eu"2"+ phosphors with different Eu"2"+-doped concentrations were calculated. A blue light-emitting diode was fabricated by combination of a 370 nm InGaN chip and the prepared phosphor Sr_5(PO_4)_3F: Eu"2"+. The present work suggests that Sr_5(PO_4)_3F: Eu"2"+ is a potential phosphor applied in InGaN-based LEDs.

Characterising and testing deep UV LEDs for use in space applications

International Nuclear Information System (INIS)

Hollington, D; Baird, J T; Sumner, T J; Wass, P J

2015-01-01

Deep ultraviolet (DUV) light sources are used to neutralise isolated test masses in highly sensitive space-based gravitational experiments. An example is the LISA Pathfinder charge management system, which uses low-pressure mercury lamps. A future gravitational-wave observatory such as eLISA will use UV light-emitting diodes (UV LEDs), which offer numerous advantages over traditional discharge lamps. Such devices have limited space heritage but are now available from a number of commercial suppliers. Here we report on a test campaign that was carried out to quantify the general properties of three types of commercially available UV LEDs and demonstrate their suitability for use in space. Testing included general electrical and UV output power measurements, spectral stability, pulsed performance and temperature dependence, as well as thermal vacuum, radiation and vibration survivability. (paper)

Characterising and testing deep UV LEDs for use in space applications

Science.gov (United States)

Hollington, D.; Baird, J. T.; Sumner, T. J.; Wass, P. J.

2015-12-01

Deep ultraviolet (DUV) light sources are used to neutralise isolated test masses in highly sensitive space-based gravitational experiments. An example is the LISA Pathfinder charge management system, which uses low-pressure mercury lamps. A future gravitational-wave observatory such as eLISA will use UV light-emitting diodes (UV LEDs), which offer numerous advantages over traditional discharge lamps. Such devices have limited space heritage but are now available from a number of commercial suppliers. Here we report on a test campaign that was carried out to quantify the general properties of three types of commercially available UV LEDs and demonstrate their suitability for use in space. Testing included general electrical and UV output power measurements, spectral stability, pulsed performance and temperature dependence, as well as thermal vacuum, radiation and vibration survivability.

Lifetime testing UV LEDs for use in the LISA charge management system

Science.gov (United States)

Hollington, D.; Baird, J. T.; Sumner, T. J.; Wass, P. J.

2017-10-01

As a future charge management light source, UV light-emitting diodes (UV LEDs) offer far superior performance in a range of metrics compared to the mercury lamps used in the past. As part of a qualification program a number of short wavelength UV LEDs have been subjected to a series of lifetime tests for potential use on the laser interferometer space antenna (LISA) mission. These tests were performed at realistic output levels for both fast and continuous discharging in either a DC or pulsed mode of operation and included a DC fast discharge test spanning 50 days, a temperature dependent pulsed fast discharge test spanning 21 days and a pulsed continuous discharge test spanning 507 days. Two types of UV LED have demonstrated lifetimes equivalent to over 25 years of realistic mission usage with one type providing a baseline for LISA and the other offering a backup solution.

Lifetime testing UV LEDs for use in the LISA charge management system

International Nuclear Information System (INIS)

Hollington, D; Baird, J T; Sumner, T J; Wass, P J

2017-01-01

As a future charge management light source, UV light-emitting diodes (UV LEDs) offer far superior performance in a range of metrics compared to the mercury lamps used in the past. As part of a qualification program a number of short wavelength UV LEDs have been subjected to a series of lifetime tests for potential use on the laser interferometer space antenna (LISA) mission. These tests were performed at realistic output levels for both fast and continuous discharging in either a DC or pulsed mode of operation and included a DC fast discharge test spanning 50 days, a temperature dependent pulsed fast discharge test spanning 21 days and a pulsed continuous discharge test spanning 507 days. Two types of UV LED have demonstrated lifetimes equivalent to over 25 years of realistic mission usage with one type providing a baseline for LISA and the other offering a backup solution. (paper)

Luminescence properties and energy transfer investigations of Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Yang, Zaifa; Xu, Denghui, E-mail: xudh@btbu.edu.cn; Sun, Jiayue; Du, Jiangnan; Gao, Xuedong

2016-09-15

Highlights: • A phosphor Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} for UV-based white LEDs was firstly synthesized successfully. • The phase structure and photoluminescence properties of samples were studied in detail. • The energy transfer process from Ce{sup 3+} to Tb{sup 3+} ions was illustrated in detail. • Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} phosphor has potential applications as an UV-convertible phosphor for white light emitting diodes. - Abstract: A series of Ce{sup 3+} or Tb{sup 3+} doped and Ce{sup 3+}/Tb{sup 3+} co-doped Sr{sub 3}Lu(PO{sub 4}){sub 3} phosphors were prepared via the conventional high temperature solid-state reaction. The phase structure, photoluminescence and energy transfer properties of samples were studied in detail. The optimal proportion of Ce{sup 3+} single doping is 4 mol% with maximal fluorescence intensity. The Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} phosphor shows both a blue emission (428 nm) from Ce{sup 3+} and a yellowish-green emission (545 nm) from Tb{sup 3+} with considerable intensity under ultraviolet (UV) excitation (268 nm). The energy transfer from Ce{sup 3+} to Tb{sup 3+} ions takes place in the Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} phosphor on the basis of the analysis of the luminescence spectra. The energy transfer mechanism from Ce{sup 3+} to Tb{sup 3+} ions was proved to be dipole–dipole interaction. The energy transfer behaviors in Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} phosphor is also investigated by the lifetime measurement. The results show that this phosphor has potential applications for UV white-light LEDs.

Analysis of green luminescent Tb3+:Ca4GdO(BO3)3 powder phosphor

International Nuclear Information System (INIS)

Vengala Rao, B.; Rambabu, U.; Buddhudu, S.

2007-01-01

This paper reports on the emission analysis of a green luminescent Tb 3+ :Ca 4 GdO(BO 3 ) 3 powder phosphor based on the measurements of excitation, emission and lifetimes. Besides this, we have also observed an intense green emission from this powder phosphor under an UV source. The emission transitions of ( 5 D 4 →7 F 3,4,5,6 ) with λ exci =257 nm have been measured. Particularly, the green emission transition ( 5 D 4 →7 F 5 ) at 553 nm has been found to be more prominent and intense. Such green strong emission displaying powder phosphor will find applications in the development of coated screens in certain electronic systems. Apart from the emission analysis of this phosphor, XRD, SEM and FTIR studies have also been carried out in order to understand the structural details of it

Synthesis and luminescent properties of novel red-emitting M7Sn(PO46:Eu3+ (M = Sr, Ba phosphors

Directory of Open Access Journals (Sweden)

Guo Feng

2018-03-01

Full Text Available Novel Eu3+-activated M7Sn(PO46 (where M = Sr, Ba red-emitting phosphors were synthesized via conventional solid-state reaction method at 1200 °C for 2 h. The luminescence properties of the prepared samples and quenching concentration of Sr7-xSn(PO46:xEu3+ and Ba7-xSn(PO46:xEu3+ were investigated. These phosphors can be efficiently excited by UV (395 nm and visible blue (465 nm light nicely matching the output wavelengths of the near-UV LEDs and InGaN blue LED chips and emit the red light. The critical concentrations of the Eu3+ activator were found to be 0.175 mol and 0.21 mol per formula unit for Sr7-xSn(PO46:xEu3+ and Ba7-xSn(PO46:xEu3+, respectively. The M7-xSn(PO46:xEu3+ (M = Sr, Ba phosphor may be a good candidate for light-emitting diodes application.

Microbial raw data for UV-C LED disinfection study

Data.gov (United States)

U.S. Environmental Protection Agency — This study evaluated ultraviolet (UV) light emitting diodes (LEDs) emitting at 260 nm, 280 nm, and the combination of 260|280 nm together for their efficacy at...

Efficient and thermally stable red luminescence from nano-sized phosphor of Gd{sub 6}MoO{sub 12}:Eu{sup 3+}

Energy Technology Data Exchange (ETDEWEB)

Qin, Lin [Soochow University, College of Chemistry, Chemical Engineering and Materials Science (China); Wei, Donglei [Pukyong National University, Department of Physics and Interdisciplinary Program of Biomedical Engineering (Korea, Republic of); Huang, Yanlin [Soochow University, College of Chemistry, Chemical Engineering and Materials Science (China); Kim, Sun Il [Pukyong National University, Department of Physics and Interdisciplinary Program of Biomedical Engineering (Korea, Republic of); Yu, Young Moon [Pukyong National University, LED-Marin Convergence Technology R and BD Center (Korea, Republic of); Seo, Hyo Jin, E-mail: hjseo@pknu.ac.kr [Pukyong National University, Department of Physics and Interdisciplinary Program of Biomedical Engineering (Korea, Republic of)

2013-09-15

A novel red-emitting nano-phosphor of Eu{sup 3+}-doped Gd{sub 6}MoO{sub 12} was successfully synthesized by the Pechini method. The crystalline phase was confirmed by X-ray powder diffraction analysis. The morphology of the nano-phosphor was analyzed by scanning electron microscopy, indicating a good crystallization with particles smaller than 500 nm. The luminescence properties such as photoluminescence spectra and decay curves were investigated. The phosphors can be efficiently excited by near-ultraviolet (near-UV) light and exhibit a bright red luminescence around 613 nm ascribed to the forced electric dipole transition {sup 5}D{sub 0}{yields}{sup 7}F{sub 2} of Eu{sup 3+} ions. The thermal stabilities were investigated from the temperature-dependent luminescence decay curves (lifetimes) and spectra intensities. The luminescence properties in relation to applications in white light-emitting diodes (W-LEDs) such as the absolute luminescence quantum efficiency, excitation wavelength, and color coordinates were discussed. The Gd{sub 6}MoO{sub 12}:Eu{sup 3+} nano-phosphor is a promising red-emitting candidate for the fabrication of W-LEDs with near-UV chips.

UV-LED-based charge control for LISA

Science.gov (United States)

Olatunde, Taiwo; Shelley, Ryan; Chilton, Andrew; Ciani, Giacomo; Mueller, Guido; Conklin, John

2014-03-01

The test masses inside the LISA gravitational reference sensors (GRS) must maintain almost pure geodesic motion for gravitational waves to be successfully detected. The residual accelerations have to stay below 3fm/s2/rtHz at all frequencies between 0.1 and 3 mHz. One of the well known noise sources is associated with the charges on the test masses which couple to stray electrical potentials and external electro-magnetic fields. The LISA pathfinder (LPF) will use Hg-discharge lamps emitting mostly around 253 nm to discharge the test masses via photoemission in its 2015/16 flight. A future LISA mission launched around 2030 will likely replace the lamps with newer UV-LEDs. UV-LEDs have a lower mass, a better power efficiency, and are smaller than their Hg counterparts. Furthermore, the latest generation produces light at 240 nm, with energy well above the work function of pure gold. I will describe a preliminary design for effective charge control through photoelectric effect by using these LEDs. The effectiveness of this method is verified by taking Quantum Efficiency (QE) measurements which relate the number of electrons emitted to the number of photons incident on the Au test mass surface. This presentation addresses our initial results and future plans which includes implementation and testing in the UF torsion pendulum and space-qualification in a small satellite mission which will launch in the summer of 2014, through a collaboration with Stanford, KACST, and NASA Ames Research Center.

Nanomaterial disordering in AlGaN/GaN UV LED structures

International Nuclear Information System (INIS)

Shabunina, E I; Levinshtein, M E; Kulagina, M M; Petrov, V N; Ratnikov, V V; Smirnova, I N; Troshkov, S I; Shmidt, N M; Kurin, S Yu; Makarov, Yu N; Chernyakov, A E; Usikov, A S; Helava, H

2015-01-01

Multifractal analysis was applied to characterize quantitatively nanostructural disordering in HVPE-grown AlGaN/GaN UV LED structures. A higher level of leakage currents shunting the active region of LEDs by an extended defect system is correlated with higher values of multifractal parameters (MFs). As a result, the concentration of injected carriers participating in radiative recombination in the active region is reduced. MFs and the conductivity of quasi-ohmic shunts localized in an extended defect system are higher in AlGaN/GaN structures than in InGaN/GaN structures. It is one of the reasons behind the low external quantum efficiency of AlGaN/GaN UV LEDs. (paper)

Mirror coatings for large aperture UV optical infrared telescope optics

Science.gov (United States)

Balasubramanian, Kunjithapatham; Hennessy, John; Raouf, Nasrat; Nikzad, Shouleh; Del Hoyo, Javier; Quijada, Manuel

2017-09-01

Large space telescope concepts such as LUVOIR and HabEx aiming for observations from far UV to near IR require advanced coating technologies to enable efficient gathering of light with important spectral signatures including those in far UV region down to 90nm. Typical Aluminum mirrors protected with MgF2 fall short of the requirements below 120nm. New and improved coatings are sought to protect aluminum from oxidizing readily in normal environment causing severe absorption and reduction of reflectance in the deep UV. Choice of materials and the process of applying coatings present challenges. Here we present the progress achieved to date with experimental investigations of coatings at JPL and at GSFC and discuss the path forward to achieve high reflectance in the spectral region from 90 to 300nm without degrading performance in the visible and NIR regions taking into account durability concerns when the mirrors are exposed to normal laboratory environment as well as high humidity conditions. Reflectivity uniformity required on these mirrors is also discussed.

Enhanced Ce{sup 3+} photoluminescence by Li{sup +} co-doping in CaO phosphor and its use in blue-pumped white LEDs

Energy Technology Data Exchange (ETDEWEB)

Hao, Zhendong, E-mail: haozd@ciomp.ac.cn; Zhang, Xia; Luo, Yongshi; Zhang, Ligong; Zhao, Haifeng; Zhang, Jiahua, E-mail: zhangjh@ciomp.ac.cn

2013-08-15

In this paper, we demonstrate a method to improve the photoluminescence of CaO: Ce{sup 3+} phosphor and delineate its first use in blue-pumped white LEDs. The results show that the yellow emission of Ce{sup 3+} is enhanced by a factor of 1.88 by adding Li{sup +} into CaO host at 474 nm blue light excitation. On analyzing the diffuse reflection spectra and fluorescence decay curves, we reveal that the photoluminescence enhancement is originated from the rise of absorbance to the excitation photons but not from the improvement of the luminescent efficiency. Li{sup +}-improved CaO: Ce{sup 3+} exhibits more red component when it is compared with the commercial Y{sub 3}Al{sub 5}O{sub 12}: Ce{sup 3+} (YAG: Ce{sup 3+}) phosphor, indicating its potential application for high color rendering white LEDs. Thus, a white LED is fabricated by combining blue InGaN LED chip with CaO: Ce{sup 3+}, Li{sup +} phosphor and a warm white light with high color rendering index (R{sub a}) of 80, low correlated color temperature (T{sub c}) of 4524 K, and sufficient luminous efficiency of 50 lm W{sup −1} is obtained. -- Highlights: • The photoluminescence of Ce{sup 3+} in CaO host was enhanced by Li{sup +} co-doping. • A CaO: Ce{sup 3+}, Li{sup +} based white LED was fabricated for the first time. • An efficient warm white light was obtained. • CaO: Ce{sup 3+}, Li{sup +} is expected to be used as a yellow phosphor for blue-pumped white LEDs.

White LED with High Package Extraction Efficiency

International Nuclear Information System (INIS)

Yi Zheng; Stough, Matthew

2008-01-01

The goal of this project is to develop a high efficiency phosphor converting (white) Light Emitting Diode (pcLED) 1-Watt package through an increase in package extraction efficiency. A transparent/translucent monolithic phosphor is proposed to replace the powdered phosphor to reduce the scattering caused by phosphor particles. Additionally, a multi-layer thin film selectively reflecting filter is proposed between blue LED die and phosphor layer to recover inward yellow emission. At the end of the project we expect to recycle approximately 50% of the unrecovered backward light in current package construction, and develop a pcLED device with 80 lm/W e using our technology improvements and commercially available chip/package source. The success of the project will benefit luminous efficacy of white LEDs by increasing package extraction efficiency. In most phosphor-converting white LEDs, the white color is obtained by combining a blue LED die (or chip) with a powdered phosphor layer. The phosphor partially absorbs the blue light from the LED die and converts it into a broad green-yellow emission. The mixture of the transmitted blue light and green-yellow light emerging gives white light. There are two major drawbacks for current pcLEDs in terms of package extraction efficiency. The first is light scattering caused by phosphor particles. When the blue photons from the chip strike the phosphor particles, some blue light will be scattered by phosphor particles. Converted yellow emission photons are also scattered. A portion of scattered light is in the backward direction toward the die. The amount of this backward light varies and depends in part on the particle size of phosphors. The other drawback is that yellow emission from phosphor powders is isotropic. Although some backward light can be recovered by the reflector in current LED packages, there is still a portion of backward light that will be absorbed inside the package and further converted to heat. Heat generated

Study of formation of deep trapping mechanism by UV, beta and gamma irradiated Eu(3+) activated SrY2O4 and Y4Al2O9 phosphors.

Science.gov (United States)

Dubey, Vikas; Kaur, Jagjeet; Parganiha, Yogita; Suryanarayana, N S; Murthy, K V R

2016-04-01

This paper reports the thermoluminescence properties of Eu(3+) doped different host matrix phosphors (SrY2O4 and Y4Al2O9). The phosphor is prepared by high temperature solid state reaction method. The method is suitable for large scale production and fixed concentration of boric acid using as a flux. The prepared samples were characterized by X-ray diffraction technique and the crystallite size calculated by Scherer's formula. The prepared phosphor characterized by Scanning Electron Microscopic (SEM), Fourier Transform Infrared (FTIR), Energy Dispersive X-ray analysis (EDX), thermoluminescence (TL) and Transmission Electron Microscopic (TEM) techniques. The prepared phosphors for different concentration of Eu(3+) ions were examined by TL glow curve for UV, beta and gamma irradiation. The UV 254nm source used for UV irradiation, Sr(90) source was used for beta irradiation and Co(60) source used for gamma irradiation. SrY2O4:Eu(3+)and Y4Al2O9:Eu(3+) phosphors which shows both higher temperature peaks and lower temperature peaks for UV, beta and gamma irradiation. Here UV irradiated sample shows the formation of shallow trap (surface trapping) and the gamma irradiated sample shows the formation of deep trapping. The estimation of trap formation was evaluated by knowledge of trapping parameters. The trapping parameters such as activation energy, order of kinetics and frequency factor were calculated by peak shape method. Here most of the peak shows second order of kinetics. The effect of gamma, beta and UV exposure on TL studies was also examined and it shows linear response with dose which indicate that the samples may be useful for TL dosimetry. Formation of deep trapping mechanism by UV, beta and gamma irradiated Eu(3+) activated SrY2O4 and Y4Al2O9 phosphors is discussed in this paper. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterization of curing behavior of UV-curable LSR for LED embedded injection mold

Science.gov (United States)

Tae, Joon-Sung; Yim, Kyung-Gyu; Rhee, Byung-Ohk; Kwak, Jae B.

2016-11-01

For many applications, liquid silicone rubber (LSR) injection molding is widely used for their great design flexibility and high productivity. In particular, a sealing part for a mobile device such as smartphone and watch has been produced by injection molding. While thermally curable LSR causes deformation problem due to a high mold temperature, UV-curable LSR can be molded at room temperature, which has advantages for over-molding with inserts of temperature-sensitive materials. Ultraviolet light-emitting diodes (UV LEDs) have advantages such as a longer service life, a lower heat dissipation, and smaller size to equip into the mold than conventional halogen or mercury UV lamps. In this work, rheological behavior of UV-curable LSR during curing process was analyzed by UV LEDs available in the market. UV-LEDs of various wave lengths and intensities were tested. The steady shear test was applied to find the starting time of curing and the SAOS was applied to find the ending time of curing to estimate processing time. In addition, the hardness change with irradiation energy was compared with the rheological data to confirm the reliability of the rheological test.

Preparation and luminescence properties of Ce3+ and Ce3+/Tb(3+)-activated Y4Si2O7N2 phosphors.

Science.gov (United States)

Xia, Zhiguo; Wu, Weiwei

2013-09-28

Ce(3+) and Ce(3+)/Tb(3+)-activated Y4Si2O7N2 phosphors are synthesized by the solid-state method, which can be efficiently excited by near ultraviolet (UV) light emitting diode (LED) chips. The PL spectrum of Y4Si2O7N2:Ce(3+) shows a broad hump between 380 and 650 nm, assigned to the electron transition from the 4f energy level to different 5d sub levels of the Ce(3+) ions at different Y(3+) sites. The color of the Y4Si2O7N2:Ce(3+) phosphor can shift from blue to green by introducing Tb(3+). In addition, the energy transfer process from Ce(3+) to Tb(3+) in the Y4Si2O7N2 host was investigated and discussed in terms of both the luminescence spectra and decay curves. The energy transfer critical distance has been calculated and evaluated by the concentration quenching method. Therefore, the Ce(3+) and Ce(3+)/Tb(3+)-activated Y4Si2O7N2 phosphors can serve as key materials for phosphor-converted white-light UV-LEDs.

Photoluminescence and Energy Transfer Properties with Y+SiO4 Substituting Ba+PO4 in Ba3Y(PO4)3:Ce(3+)/Tb(3+), Tb(3+)/Eu(3+) Phosphors for w-LEDs.

Science.gov (United States)

Li, Kai; Liang, Sisi; Shang, Mengmeng; Lian, Hongzhou; Lin, Jun

2016-08-01

A series of Ce(3+), Tb(3+), Eu(3+) doped Ba2Y2(PO4)2(SiO4) (BYSPO) phosphors were synthesized via the high-temperature solid-state reaction route. X-ray diffraction, high-resolution transmission electron microscopy, Fourier transform infrared, solid-state NMR, photoluminescence (PL) including temperature-dependent PL, and fluorescent decay measurements were conducted to characterize and analyze as-prepared samples. BYSPO was obtained by the substitution of Y+SiO4 for Ba+PO4 in Ba3Y(PO4)3 (BYPO). The red shift of PL emission from 375 to 401 nm occurs by comparing BYSPO:0.14Ce(3+) with BYPO:0.14Ce(3+) under 323 nm UV excitation. More importantly, the excitation edge can be extended from 350 to 400 nm, which makes it be excited by UV/n-UV chips (330-410 nm). Tunable emission color from blue to green can be observed under 365 nm UV excitation based on the energy transfer from Ce(3+) to Tb(3+) ions after codoping Tb(3+) into BYSPO:0.14Ce(3+). Moreover, energy transfer from Tb(3+) to Eu(3+) ions also can be found in BYSPO:Tb(3+),Eu(3+) phosphors, resulting in the tunable color from green to orange red upon 377 nm UV excitation. Energy transfer properties were demonstrated by overlap of excitation spectra, variations of emission spectra, and decay times. In addition, energy transfer mechanisms from Ce(3+) to Tb(3+) and Tb(3+) to Eu(3+) in BYSPO were also discussed in detail. Quantum yields and CIE chromatic coordinates were also presented. Generally, the results suggest their potential applications in UV/n-UV pumped LEDs.

White light quality of phosphor converted light-emitting diodes: A phosphor materials perspective of view

International Nuclear Information System (INIS)

Sommer, Christian; Hartmann, Paul; Pachler, Peter; Hoschopf, Hans; Wenzl, Franz P.

2012-01-01

Highlights: ► We discuss the impact of the optical properties of a phosphor for colour temperature constancy in solid state lighting. ► Quantitative evaluation of permissible variations of the optical properties for batch-to-batch reproducibility. ► Quantitative evaluation of permissible variations of the optical properties upon temperature increase. ► Quantitative evaluation of permissible variations of the optical properties upon materials degradation. - Abstract: For a systematic approach to improve the white light quality of phosphor converted LEDs and to fulfil the demands for colour temperature reproducibility and constancy, it is imperative to understand how variations of the extinction coefficient and the quantum efficiency of the phosphor particles as well as variations of the excitation wavelength of the blue LED die affect the correlated colour temperature of the white LED source. Based on optical ray tracing of a phosphor converted white LED package we deduce permissible values for the variation of a given extinction coefficient and a given quantum efficiency of a phosphor material in order to maintain acceptable colour variations. These quantitative valuations of the required constancy of the optical properties of the phosphors will in particular provide some benchmarks for the synthesis of improved phosphor materials aiming at solid state lighting applications.

Salt-embedded carbon nanodots as a UV and thermal stable fluorophore for light-emitting diodes

International Nuclear Information System (INIS)

Kim, Tak H.; Wang, Fu; McCormick, Paul; Wang, Lianzhou; Brown, Chris; Li, Qin

2014-01-01

UV and thermal stable, photoluminescent carbon dots (CDs) prepared by embedding CDs in ionic salt crystals such as NaCl, KCl, KBr are demonstrated. The salt crystal embedding matrix does not interfere with CDs strong emission, and provides effective protection to CDs from the environment. The degradation of 20% of the initial luminescence intensity of salt-encapsulated CDs (S-CDs) is 15 times slower under UV and 6 times slower under heat compared to that of CDs in silica matrix. We also demonstrate that the S-CDs can be applied as a color-converting phosphor for typical GaN UV light emitting diodes (LEDs) with significant improvements in stability as well as processability. - Highlights: • Carbon dots can be uniformly embedded in ionic salt crystals via crystallization. • Salt crystals provide oxygen-tight matrices for protecting carbon dots from degradations. • Salt-embedded carbon dots can be applied as a stable color-converting phosphor in LEDs

Salt-embedded carbon nanodots as a UV and thermal stable fluorophore for light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Kim, Tak H. [Queensland Micro- and Nano-Technology Centre, Griffith University, Nathan, QLD 4111 (Australia); Environmental Engineering, Griffith University, QLD 4111 (Australia); Wang, Fu [Institute of Physiology, University of Freiburg, Hermann-Herder-Street 7, 79104 Freiburg (Germany); McCormick, Paul [School of Mechanical and Chemical Engineering, The University of Western Australia, WA 2009 (Australia); Wang, Lianzhou [School of Chemical Engineering, The University of Queensland, QLD 4072 (Australia); Brown, Chris [Queensland Micro- and Nano-Technology Centre, Griffith University, Nathan, QLD 4111 (Australia); Li, Qin, E-mail: qin.li@griffith.edu.au [Queensland Micro- and Nano-Technology Centre, Griffith University, Nathan, QLD 4111 (Australia); Environmental Engineering, Griffith University, QLD 4111 (Australia)

2014-10-15

UV and thermal stable, photoluminescent carbon dots (CDs) prepared by embedding CDs in ionic salt crystals such as NaCl, KCl, KBr are demonstrated. The salt crystal embedding matrix does not interfere with CDs strong emission, and provides effective protection to CDs from the environment. The degradation of 20% of the initial luminescence intensity of salt-encapsulated CDs (S-CDs) is 15 times slower under UV and 6 times slower under heat compared to that of CDs in silica matrix. We also demonstrate that the S-CDs can be applied as a color-converting phosphor for typical GaN UV light emitting diodes (LEDs) with significant improvements in stability as well as processability. - Highlights: • Carbon dots can be uniformly embedded in ionic salt crystals via crystallization. • Salt crystals provide oxygen-tight matrices for protecting carbon dots from degradations. • Salt-embedded carbon dots can be applied as a stable color-converting phosphor in LEDs.

Synthesis and tunable luminescence properties of Eu2+ and Tb3+-activated Na2Ca4(PO4)3F phosphors based on energy transfer

International Nuclear Information System (INIS)

Zhou, Jun; Xia, Zhiguo; You, Hongpeng; Shen, Kai; Yang, Mengxia; Liao, Libing

2013-01-01

A series of color-tunable blue–green emitting Na 2 Ca 4 (PO 4 ) 3 F:Eu 2+ ,Tb 3+ phosphors were prepared by a high temperature solid-state reaction. Their luminescence properties reveal that there is an efficient energy transfer from Eu 2+ to Tb 3+ ions via a dipole–quadrupole mechanism where Eu 2+ ions exhibit a strong excitation band in near ultraviolet (UV) region, matching well with the dominant emission band of near UV (350–420 nm) LED chips, and Eu 2+ and Tb 3+ ions can give characteristic blue and green emission light. The varied color of the phosphors from blue to green can be achieved by properly tuning the relative ratio of Eu 2+ to Tb 3+ dopant through the energy transfer from Eu 2+ to Tb 3+ ions. Thermal quenching luminescence results reveal that Na 2 Ca 4 (PO 4 ) 3 F:Eu 2+ ,Tb 3+ exhibits good thermal stability. These results demonstrate that Tb 3+ ion with low 4f–4f absorption efficiency in near UV region can play the role of an activator in narrow green-emitting phosphor through efficient energy feeding by allowing 4f–5d absorption of Eu 2+ with high oscillator strength. The present Eu 2+ –Tb 3+ codoped Na 2 Ca 4 (PO 4 ) 3 F phosphor will have potential application for the near UV white LEDs. - Highlights: ► Color-tunable blue–green Na 2 Ca 4 (PO 4 ) 3 F:Eu 2+ ,Tb 3+ phosphors were prepared. ► Eu 2+ –Tb 3+ energy transfer process and mechanism discussed. ► Thermal quenching properties of blue and green phosphors were studied.

Ambient temperature effects on broadband UV-B measurements using fluorescent phosphor (MgWO4)-based detectors

Science.gov (United States)

Dichter, Bronislaw K.; Beaubien, David J.; Beaubien, Arthur F.

1994-01-01

Results of field tests on a group of broadband UV-B pyranometers are presented. A brief description of the instrument is given. The effects of ambient temperature on thermally unregulated fluorescent phosphor (Robertson type) meters are presented and compared with the performance of thermally stabilized instruments. Means for correcting data from thermally unregulated instruments, where the prevailing ambient temperatures are known, are outlined.

Luminescence and luminescence quenching of highly efficient Y2Mo4O15:Eu3+ phosphors and ceramics

OpenAIRE

Janulevičius, Matas; Marmokas, Paulius; Misevičius, Martynas; Grigorjevaitė, Julija; Mikoliūnaitė, Lina; Šakirzanovas, Simas; Katelnikovas, Artūras

2016-01-01

A good LED phosphor must possess strong enough absorption, high quantum yields, colour purity, and quenching temperatures. Our synthesized Y2Mo4O15:Eu3+ phosphors possess all of these properties. Excitation of these materials with near-UV or blue radiation yields bright red emission and the colour coordinates are relatively stable upon temperature increase. Furthermore, samples doped with 50% Eu3+ showed quantum yields up to 85%, what is suitable for commercial application. Temperature depend...

Computer numerical control (CNC) lithography: light-motion synchronized UV-LED lithography for 3D microfabrication

International Nuclear Information System (INIS)

Kim, Jungkwun; Allen, Mark G; Yoon, Yong-Kyu

2016-01-01

This paper presents a computer-numerical-controlled ultraviolet light-emitting diode (CNC UV-LED) lithography scheme for three-dimensional (3D) microfabrication. The CNC lithography scheme utilizes sequential multi-angled UV light exposures along with a synchronized switchable UV light source to create arbitrary 3D light traces, which are transferred into the photosensitive resist. The system comprises a switchable, movable UV-LED array as a light source, a motorized tilt-rotational sample holder, and a computer-control unit. System operation is such that the tilt-rotational sample holder moves in a pre-programmed routine, and the UV-LED is illuminated only at desired positions of the sample holder during the desired time period, enabling the formation of complex 3D microstructures. This facilitates easy fabrication of complex 3D structures, which otherwise would have required multiple manual exposure steps as in the previous multidirectional 3D UV lithography approach. Since it is batch processed, processing time is far less than that of the 3D printing approach at the expense of some reduction in the degree of achievable 3D structure complexity. In order to produce uniform light intensity from the arrayed LED light source, the UV-LED array stage has been kept rotating during exposure. UV-LED 3D fabrication capability was demonstrated through a plurality of complex structures such as V-shaped micropillars, micropanels, a micro-‘hi’ structure, a micro-‘cat’s claw,’ a micro-‘horn,’ a micro-‘calla lily,’ a micro-‘cowboy’s hat,’ and a micro-‘table napkin’ array. (paper)

White Light Emitting MZr4(PO4)6:Dy3+ (M = Ca, Sr, Ba) Phosphors for WLEDs.

Science.gov (United States)

Nair, Govind B; Dhoble, S J

2017-03-01

A series of MZr 4 (PO 4 ) 6 :Dy 3+ (M = Ca, Sr, Ba) phosphors were prepared by the solid state diffusion method. Confirmation of the phase formation and morphological studies were performed by X-ray powder diffraction (XRD) measurements and scanning electron microscopy, respectively. Photoluminescence (PL) properties of these phosphors were thoroughly analyzed and the characteristic emissions of Dy 3+ ions were found to arise from them at an excitation wavelength of 351 nm. The PL emission spectra of the three phosphors were analyzed and compared. The CIE chromaticity coordinates assured that the phosphors produced cool white-light emission and hence, they are potential candidates for UV excited white-LEDs (WLEDs). Graphical Abstract ᅟ.

Characteristics of the Panasonic UD-802 phosphors

International Nuclear Information System (INIS)

Ben-Shachar, B.; Catchen, G.L.; Hoffman, J.M.

1989-01-01

Several basic dosimetric characteristics of Li 2 B 4 O 7 :Cu and CaSO 4 :Tm phosphors in Panasonic UD-802 dosemeters were measured. The TL dose response linearity was determined over the useful range of personnel and environmental dosimetry (0.005 - 10 mGy), and the minimum measurable doses were calculated. The intrinsic ultraviolet (UV) radiation sensitivity of both phosphors was checked before and after γ irradiation for the purpose of re-assessing high doses. The results indicate that Li 2 B 4 O 7 :Cu is UV sensitive and, therefore, re-assessment is not applicable. Although the CaSO 4 :Tm phosphor exhibited UV sensitivity after γ irradiation, the results were not consistent with those reported earlier and more study is required. The fading of both phosphors was evaluated in Panasonic UD-801 dosemeters for periods up to 90 days. (author)

Preparations and applications in UV curing coatings of epoxy acrylates containing carboxyl

International Nuclear Information System (INIS)

Wu Yu Min

1999-01-01

This paper introduces preparations of epoxy acrylates containing carboxyl through the reactions of epoxy acrylates with butanedioic anhydride, pentanedioic anhydride, cis-butenedioic anhydride, phthalic anhydride, tetrabromophthalic anhydride and -tetrahydrophthalic anhydride. These epoxy acrylates containing carboxyl have been applied to UV-curing coatings and their effects on properties of UV-curing coatings have been studied

Enhanced luminescence in SrMgAl(x)O(17±δ):yMn4+ composite phosphors.

Science.gov (United States)

Cao, Renping; Sharafudeen, Kaniyarakkal N; Qiu, Jianrong

2014-01-03

Red-emitting SrMgAlxO17±δ:yMn(4+) composite phosphors (x=10-100; y=0.05-4.0 mol%) are synthesized by solid-state reaction method in air. Addition of Al2O3 leads to the formation of two concomitant phases, i.e., SrMgAl10O17 and Al2O3 phases in the composite phosphor. Red emission from Mn(4+) ions in the composite phosphors is greatly enhanced due to multiple scattering and absorption of excitation light between SrMgAl10O17 and Al2O3 phases. SrMgAlxO17±δ:yMn(4+) composite phosphors would be a promising candidate as red phosphor in the application of a 397 nm near UV-based W-LED. Copyright © 2013 Elsevier B.V. All rights reserved.

CFD modeling of a UV-LED photocatalytic odor abatement process in a continuous reactor

International Nuclear Information System (INIS)

Wang, Zimeng; Liu, Jing; Dai, Yuancan; Dong, Weiyang; Zhang, Shicheng; Chen, Jianmin

2012-01-01

Highlights: ► A CFD model is developed for a UV-LED based photocatalytic deodorization reactor. ► Radiation field model and Langmuir–Hinshelwood kinetics are integrated in the model. ► The model can predict the pollutant concentration profile and the reactor performance. ► LED distance is predicted to be a critical parameter in photocatalytic reactor design. - Abstract: This paper presents a model study of a UV light-emitting-diode (UV-LED) based photocatalytic odor abatement process. It integrated computational fluid dynamics (CFD) modeling of the gas flow in the reactor with LED-array radiation field calculation and Langmuir–Hinshelwood reaction kinetics. It was applied to simulate the photocatalytic degradation of dimethyl sulfide (DMS) in a UV-LED reactor based on experimentally determined chemical kinetic parameters. A non-linear power law relating reaction rate to irradiation intensity was adopted. The model could predict the steady state DMS concentration profiles by calculating the advection, diffusion and Langmuir–Hinshelwood reaction kinetics. By affecting the radiation intensity and uniformity, the position of the LED array relative to the catalyst appeared to be a critical parameter determining DMS removal efficiency. Too small distances might yield low quantum efficiency and consequently poor abatement performance. This study provided an example of LED-based photocatalytic process modeling and gave insights into the optimization of light source design for photocatalytic applications.

Synthesis, luminescent properties and white light emitting diode application of Ba{sub 7}Zr(PO{sub 4}){sub 6}:Eu{sup 2+} yellow-emitting phosphor

Energy Technology Data Exchange (ETDEWEB)

Li, Chenxia; Dai, Jian [College of Optical and Electronic Technology, China Jiliang University, Hangzhou 310018 (China); Deng, Degang, E-mail: dengdegang@cjlu.edu.cn [College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China); Shen, Changyu [College of Optical and Electronic Technology, China Jiliang University, Hangzhou 310018 (China); Xu, Shiqing, E-mail: sxucjlu@163.com [College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China)

2015-10-15

A yellow-emitting phosphor, Eu{sup 2+}-activated Ba{sub 7}Zr(PO{sub 4}){sub 6} phosphor was synthesized by solid-state reaction method and the luminescence properties were investigated. The phosphor exhibited strong absorption in near ultraviolet (n-UV) region, which matched well with the n-UV chip. Upon excitation at 370 nm, the Ba{sub 7}Zr(PO{sub 4}){sub 6}:Eu{sup 2+} phosphor has a broad yellow emission band with a peak at 585 nm and a full width at half maximum of 178 nm wider than that of the commercial yellow-emitting YAG:Ce{sup 3+} phosphor. The mechanism of concentration quenching of Eu{sup 2+} ions in Ba{sub 7}Zr(PO{sub 4}){sub 6} phosphor is verified to be energy transfer among the nearest neighbor Eu{sup 2+} ions. The CIE value and temperature dependence of photoluminescence were also discussed. Furthermore, a white-LED was fabricated using a 370 nm UV chip pumped with a blend of phosphors consisting of yellow-emitting Ba{sub 6.97}Zr(PO{sub 4}){sub 6}:0.03Eu{sup 2+} and blue-emitting BaMgAl{sub 10}O{sub 17}:Eu{sup 2+} phosphors, which achieved a CIE of (0.3329, 0.3562) with a color-rendering index of 86.4 around the CCT of 5487 K.

High-Power 365 nm UV LED Mercury Arc Lamp Replacement for Photochemistry and Chemical Photolithography.

Science.gov (United States)

Hölz, K; Lietard, J; Somoza, M M

2017-01-03

Ultraviolet light emitting diodes (UV LEDs) have become widespread in chemical research as highly efficient light sources for photochemistry and photopolymerization. However, in more complex experimental setups requiring highly concentrated light and highly spatially resolved patterning of the light, high-pressure mercury arc lamps are still widely used because they emit intense UV light from a compact arc volume that can be efficiently coupled into optical systems. Advances in the deposition and p -type doping of gallium nitride have recently permitted the manufacture of UV LEDs capable of replacing mercury arc lamps also in these applications. These UV LEDs exceed the spectral radiance of mercury lamps even at the intense I-line at 365 nm. Here we present the successful exchange of a high-pressure mercury arc lamp for a new generation UV LED as a light source in photolithographic chemistry and its use in the fabrication of high-density DNA microarrays. We show that the improved light radiance and efficiency of these LEDs offer substantial practical, economic and ecological advantages, including faster synthesis, lower hardware costs, very long lifetime, an >85-fold reduction in electricity consumption and the elimination of mercury waste and contamination.

Blue to bluish-green tunable phosphor Sr2LiSiO4F:Ce3+,Tb3+ and efficient energy transfer for near-ultraviolet light-emitting diodes

International Nuclear Information System (INIS)

Xie, Mubiao; Zeng, Lihua; Ye, TingLi; Yang, Xi; Zhu, Xianmei; Peng, Siyun; Lei, Lei

2014-01-01

Ce 3+ and Tb 3+ activated Sr 2 LiSiO 4 F phosphors were prepared by a solid state reaction technique at high temperature, and their ultraviolet (UV)-visible spectroscopic properties were investigated. Under ultraviolet light excitation, Ce 3+ -doped Sr 2 LiSiO 4 F phosphors emit blue light (420 nm), while Tb 3+ -doped phosphors show yellowish green emission. Efficient energy transfer from Ce 3+ to Tb 3+ ions in co-doped samples was confirmed in terms of corresponding excitation and emission spectra. The energy transfer mechanism between Ce 3+ and Tb 3+ was discussed and demonstrated to be dipole–dipole interaction in Sr 2 LiSiO 4 F:Ce 3+ ,Tb 3+ phosphors. Due to energy transfer from Ce 3+ to Tb 3+ , Ce 3+ and Tb 3+ co-doped Sr 2 LiSiO 4 F phosphors show intense absorption in near-UV region, and present tunable emission from blue to bluish green under 360 nm light excitation. The results indicate that these phosphors can be considered as candidates for white LEDs pumped by n-UV chips. (paper)

Mechanical and thermal properties of UV curable polyurethane acrylate composite coatings

International Nuclear Information System (INIS)

Mohd Sofian Alias; Nik Ghazali Nik Salleh; Mohd Hamzah Harun; Mohd Yusof Hamzah; Rosley Che Ismail

2012-01-01

UV curable coating formulation comprises urethane acrylate resin and nano silica as filter were synthesized to develop UV curable inorganic hybrid composite (PUA). The surface of the nano silica was chemically modified to improve its chemical interaction within the urethane acrylate matrix. The modification had been undertaken by applying vinyltrymetoxysilane (VTMOS) that acted as a coupling agent to produce organophilic silica shell (SIMA). The shell is linked to the silica via reaction with the surface silanol group of the silica. The disappearance of methoxy groups in VTMOS was demonstrated by FTIR spectrum. The percentage of silica particles in UV curable hybrid formulation were varied on 5 %, 10 %, 15 %, 20 % and 25 wt % respectively. In this work, the formulation was applied on medium density fiber board (MDF) substrate and subsequent has been irradiated under UV light. Then, the coated MDF were characterized by several testing equipment (TGA, DSC, scratch tester, instron, SEM). From the result, we found that the addition of silica nanoparticles exhibit significant improvement in coating film properties as compared to film without silica nanoparticle includes significant improvement in its modulus and scratch resistance. This make them as promising coating candidate for MDF product. On the other hand, we also found that an increase of silica particle up to 25 wt %, the viscosity has increased rapidly indicates that it is not suitable for acrylate coating formulation due to disappearance of desired effect known as thixotropy. (Author)

High power deep UV-LEDs for analytical optical instrumentation

Czech Academy of Sciences Publication Activity Database

Li, Y.; Dvořák, Miloš; Nesterenko, P. N.; Nuchtavorn, N.; Macka, M.

2018-01-01

Roč. 255, č. 2 (2018), s. 1238-1243 ISSN 0925-4005 Institutional support: RVO:68081715 Keywords : deep UV Light emitting diodes (LEDs) * optical detection * portable analytical instrumentation Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Analytical chemistry Impact factor: 5.401, year: 2016

Output blue light evaluation for phosphor based smart white LED wafer level packages.

Science.gov (United States)

Kolahdouz, Zahra; Rostamian, Ali; Kolahdouz, Mohammadreza; Ma, Teng; van Zeijl, Henk; Zhang, Kouchi

2016-02-22

This study presents a blue light detector for evaluating the output light of phosphor based white LED package. It is composed of a silicon stripe-shaped photodiode designed and implemented in a 2 μm BiCMOS process which can be used for wafer level integration of different passive and active devices all in just 5 lithography steps. The final device shows a high selectivity to blue light. The maximum responsivity at 480 nm is matched with the target blue LED illumination. The designed structure have better responsivity compared to simple photodiode structure due to reducing the effect of dead layer formation close to the surface because of implantation. It has also a two-fold increase in the responsivity and quantum efficiency compared to previously similar published sensors.

Tunable emission and the systematic study on energy-transfer properties of Ce3+- and Tb3+-co-doped Sr3(PO4)2 phosphors

International Nuclear Information System (INIS)

Liu, Zhijun

2015-01-01

An emitting color tunable phosphor Sr 3 (PO 4 ) 2 :Ce 3+ , Tb 3+ was synthesized by the traditional high-temperature solid-state reaction method. The photoluminescence and energy-transfer (ET) properties of Ce 3+ - and Tb 3+ -doped Sr 3 (PO 4 ) 2 host were studied in detail. The obtained phosphors show both a blue emission from Ce 3+ and a yellowish green emission from Tb 3+ with considerable intensity under ultraviolet (UV) excitation (∝311 nm). When the content of Ce 3+ was fixed at 0.03, the emission chromaticity coordinates could be adjusted from blue to green region by tuning the contents of Tb 3+ ions with the aid of ET process. The critical distance between Ce 3+ and Tb 3+ is 14.69 A. The ET mechanism from Ce 3+ to Tb 3+ ions was identified with dipole-dipole interaction. The obtained phosphor exhibits a strong excitation in UV spectral region and high-efficient ET from Ce 3+ to Tb 3+ ions. It may find applications as a green light-emitting UV-convertible phosphor in white LED devices. (orig.)

Rapid Assessment of Tablet Film Coating Quality by Multispectral UV Imaging

DEFF Research Database (Denmark)

Klukkert, Marten; Wu, Jian X.; Rantanen, Jukka

2016-01-01

and coated with a polyvinyl alcohol-polyethylene glycol graft copolymer using a pan coater. It was demonstrated that the coating intactness can be assessed accurately and fast by UV imaging. The different types of coating defects could be differentiated and localized based on multivariate image analysis...

coating layers under the UV loading

Directory of Open Access Journals (Sweden)

Kulhavý Petr

2017-01-01

Full Text Available For individual components as well as for the final products is need to determine their resistance and other mechanical properties, which can be changing due to the various conditions and simultaneously we try to get still closer to the real operating conditions.Currently, given the need to guarantee a perfect quality of the product throughout its entire life cycle, it is necessary to assess the protective layers that are in direct contact with the material itself or with the future products.This article presents the results of testing individual components of the selected materials and their resistance to the UV rays. These were some samples of a prelacquered sheet and a powder coated plate after their forming, next by pigment colored concrete cubes, artificial wood and a prototype sample of the translucent material Licrete. Compared to a conventional climate tests such as heat, cold, humidity or the salt chambers, the colored protection layers were subjected to a strong UV rays. Subsequently was evaluated the change of the colors, brightness and where it was possible also the adhesion parameters and thickness of the coated layer. The measurement wasn’t focused only on the adhesion and color stability, but also to a violation of microstructure due to high temperatures caused by the UV ray. The selected specimens were tested in a device which simulates solar radiation and then were them evaluated the changes of a colors and on the surface structure.

Rare Earth Doped Lanthanum Calcium Borate Polycrystalline Red Phosphors

Directory of Open Access Journals (Sweden)

H. H. Xiong

2014-01-01

Full Text Available Single-phased Sm3+ doped lanthanum calcium borate (SmxLa2−xCaB10O19, SLCB, x=0.06 polycrystalline red phosphor was prepared by solid-state reaction method. The phosphor has two main excitation peaks located at 398.5 nm and 469.0 nm, which are nicely in accordance with the emitting wavelengths of commercial near-UV and blue light emitting diode chips. Under the excitation of 398.0 nm, the dominant red emission of Sm3+ in SLCB phosphor is centered at 598.0 nm corresponding to the transition of 4G5/2 → 6H7/2. The Eu3+ fluorescence in the red spectral region is applied as a spectroscopic probe to reveal the local site symmetry in the host lattice and, hence, Judd-Ofelt parameters Ωt  (t=2, 4 of Eu3+ in the phosphor matrix are derived to be 3.62×10-20 and 1.97×10-20 cm2, indicating a high asymmetrical and strong covalent environment around rare earth luminescence centers. Herein, the red phosphors are promising good candidates employed in white light emitting diodes (LEDs illumination.

Laser discrimination by stimulated emission of a phosphor

Science.gov (United States)

Mathur, V. K.; Chakrabarti, K.

1991-01-01

A method for discriminating sources of UV, near infrared, and far infrared laser radiation was discovered. This technology is based on the use of a single magnesium sulfide phosphor doubly doped with rare earth ions, which is thermally/optically stimulated to generate colors correlatable to the incident laser radiation. The phosphor, after initial charging by visible light, exhibits green stimulated luminescence when exposed to a near infrared source (Nd: YAG laser). On exposure to far infrared sources (CO2 laser) the phosphor emission changes to orange color. A UV laser produces both an orange red as well as green color. A device using this phosphor is useful for detecting the laser and for discriminating between the near infrared, far infrared, and UV lasers. The technology is also capable of infrared laser diode beam profiling since the radiation source leaves an imprint on the phosphor that can be photographed. Continued development of the technology offers potential for discrimination between even smaller bandwidths within the infrared spectrum, a possible aid to communication or wavemixing devices that need to rapidly identify and process optical signals.

Preparation and luminescence properties of Eu2+-doped CaSi2O2-dN2+2/3d phosphors

International Nuclear Information System (INIS)

Gu Yunxin; Zhang Qinghong; Wang Hongzhi; Li Yaogang

2009-01-01

Eu 2+ -doped CaSi 2 O 2-d N 2+2/3d phosphors for white LED lamps were prepared by solid-state reaction, and the effects of heat-treatment conditions and the overall composition of host lattice on the optical properties have been discussed. Eu 2+ -doped CaSi 2 O 2-d N 2+2/3d displayed a single broad emission band peak at 540 nm, which could be assigned to the allowed transition of Eu 2+ from the lowest crystal field component of 4f 6 5d to 4f 7 ground-state level. The excitation band of samples, extending from UV to blue, is extremely wide, so the phosphors are suitable for white LED lamps in combination with a UV or blue LED dies. The highest PL intensity is found for the sample sintered at 1400 0 C. Moreover, the emission intensity decreases when N partially replaces O. A red shift of emission wavelength did not occur with increasing of the N content.

Intense blue upconversion emission and intrinsic optical bistability in Tm3+/Yb3+/Zn2+ tridoped YVO4 phosphors

Science.gov (United States)

Yadav, Manglesh; Mondal, Manisha; Mukhopadhyay, Lakshmi; Rai, Vineet Kumar

2018-04-01

Tm3+/Yb3+/Zn2+:yttrium metavanadate (YVO4) phosphors prepared through chemical coprecipitation and the solid state reaction method have been structurally characterized by an x-ray diffraction (XRD) study. Photoluminescence study of the developed phosphors under ultraviolet (UV) and near infrared (NIR) excitation has been performed. The excitation spectrum of the tetragonal zircon type YVO4 phosphors corresponding to the emission at ˜476 nm exhibits a broad excitation peak in the 250-350 nm region, which is due to charge distribution in the {{{{VO}}}4}3- group. Under 980 nm CW diode laser excitation, enhancements of about ˜3000 times and ˜40 times have been observed for the blue band in the tridoped Tm3+Yb3+Zn2+:YVO4 phosphors compared to those of the Tm3+:YVO4 singly and Tm3+/Yb3+:YVO4 codoped phosphors, respectively. A downconversion (DC) emission study shows an enhancement of about ˜50 times for the blue band in the tridoped phosphors compared to that of the singly doped phosphors. Optical bistability (OB) behavior of the developed phosphors has been also investigated upon 980 nm excitation. The calculated Commission Internationale de l’Éclairage (CIE) color coordinates lie in the blue region with 96.5% color purity under 980 nm excitation, having a color temperature of ˜3400 K. Our observations show that the developed phosphors may be suitably used in dual mode luminescence spectroscopy, display devices, and UV LED chips.

Neutron scintillator using Ga-doped ZnO phosphor with high detection efficiency

International Nuclear Information System (INIS)

Koyama, Shin; Kinoshita, Atsushi; Fujiwara, Akihiko; Kobayashi, Haruki; Takei, Yoshinori; Nanto, Hidehito; Katagiri, Masaki

2009-01-01

Zinc Oxide (ZnO) family phosphors as phosphor for neutron detector have prepared using Spark Plasma Sintering (SPS) method. The optical properties of ZnO phosphor prepared are investigated. The following results were obtained. Two dominant photoluminescence (PL) emission peaks at 395 nm and 495 nm were observed. The lifetime of the PL emission peak at 395 nm (UV emission band) is about 20 ns, which is suitable for neutron detection. The Ga (30 mol%)-doped ZnO phosphor exhibited an intense UV emission band without the visible emission band. The Ga-doped ZnO phosphor can be prepared at the atmospheric pressure of about 8 Pa using SPS method. It was found that the PL intensity of UV emission band is increased with improving the crystallinity of the ZnO phosphor. (author)

Effect of sol aging time on the anti-reflective properties of silica coatings templated with phosphoric acid

Directory of Open Access Journals (Sweden)

Wen Wen

Full Text Available Silica anti-reflective coatings have been prepared by a sol–gel dip-coating process using the sol containing phosphoric acid as a pore-forming template. The effect of the aging time of the sol on the anti-reflective properties has been investigated. The surface topography of the silica AR coatings has been characterized. With increasing sol aging time, more over-sized pores larger than 100 nm are formed in the silica coatings. These could act as scattering centers, scattering visible light and thereby lowering transmittance. The optimal aging time was identified as 1 day, and the corresponding silica coatings showed a maximum transmittance of 99.2%, representing an 8% increase compared to the bare glass substrate. Keywords: Thin films, Anti-reflective coatings, Aging, Dip-coating, Sol–gel preparation

Enhanced red emission of LaVO4:Eu3+ phosphors by Li-doping

International Nuclear Information System (INIS)

Park, Sung Wook; Yang, Hyun Kyoung; Chung, Jong Won; Moon, Byung Kee; Choi, Byung Chun; Jeong, Jung Hyun; Jang, Ki Wan; Lee, Ho Sueb; Yi, Soung Soo

2010-01-01

LaVO 4 phosphors were synthesized by using a solid state reaction, and were characterized by using X-ray diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence (PL). The XRD patterns of the Li-doped LaVO 4 :Eu 3+ powder phosphors revealed a mixture of tetragonal and monoclinic phases. The tetragonal phase of the LaVO 4 :Eu 3+ phosphor showed a higher PL intensity than the monoclinic one, despite the presence of both monoclinic and tetragonal structures. The Li-doped LaVO 4 :Eu 3+ powder phosphors absorbed strongly at 396 nm and exhibited strong red emission at approximately 619.5 nm due to the 5 D 0 → 7 F 2 transition. The incorporation of Li + ions into the LaVO 4 :Eu 3+ powder can lead to a remarkable increase in photoluminescence. The enhanced luminescence is attributed to the incorporation of Li + ions that may act as a sensitizers for effective energy transfer. This phosphor has promising applications in near-UV light-emitting diodes(LEDs).

LED-induced fluorescence diagnostics for turbine and combustion engine thermometry

International Nuclear Information System (INIS)

Allison, S.W.

2001-01-01

Fluorescence from phosphor coatings is the basis of an established technique for measuring temperature in a wide variety of turbine and combustion engine applications. Example surfaces include blades, vanes, combustors, intake valves, pistons, and rotors. Many situations that are remote and noncontact require the high intensity of a laser to illuminate the phosphor, especially if the surface is moving. Thermometric resolutions of 0.1 C are obtainable, and some laboratory versions of these systems have been calibrated against NIST standards to even higher precision. To improve the measurement signal-to-noise ratio, synchronous detection timing has been used to repeatedly interrogate the same blade in a high speed rotating turbine. High spatial resolution can be obtained by tightly focusing the interrogation beam in measurements of static surfaces, and by precise differential timing of the laser pulses on rotating surfaces. We report here the use of blue light emitting diodes (LEDs) as a n illumination source for producing useable fluorescence from phosphors for temperature measurements. An LED can excite most of the same phosphors used to cover the temperature range from 8 to 1400 C. The advantages of using LEDs are obvious in terms of size, power requirements, space requirements and cost. There can also be advantages associated with very long operating lifetimes, wide range of available colors, and their broader emission bandwidths as compared to laser diodes. Temperature may be inferred either from phase or time-decay determinations

Red emitting phosphors of Eu3+ doped Na2Ln2Ti3O10 (Ln = Gd, Y) for white light emitting diodes

International Nuclear Information System (INIS)

Zhang, Niumiao; Guo, Chongfeng; Yin, Luqiao; Zhang, Jianhua; Wu, Mingmei

2015-01-01

Highlights: • Layered red phosphors Na 2 Ln 2 Ti 3 O 10 (Ln = Gd, Y):Eu 3+ were prepared. • The synthesis parameters of phosphors were optimized. • PL and thermal stability of the samples were investigated. • LED devices were also fabricated including the present red phosphor. - Abstract: A series of Eu 3+ doped Na 2 Ln 2 Ti 3 O 10 (Ln = Gd, Y) red-emitting phosphors for application in ultraviolet based light emitting diodes (LEDs) were successfully synthesized by a modified sol–gel method. Their structure and luminescent properties were characterized by powder X-ray diffraction (XRD), photoluminescence excitation (PLE) and emission (PL) spectra and absorption spectra, according to these results the optimal compositions and synthesis parameters were determined. In addition, the thermal stabilities of the phosphors were investigated according to the temperature-dependent PL spectra. The red and white-LEDs (W-LEDs) comprising the Na 2 Ln 2 Ti 3 O 10 :Eu 3+ (Ln = Gd, Y) red emitting phosphors were fabricated with a near-ultraviolet (n-UV) chip. In comparison with Na 2 Y 1.4 Eu 0.6 Ti 3 O 10 , the Na 2 Gd 0.6 Eu 1.4 Ti 3 O 10 phosphor offers higher brightness, quantum efficiency, and excellent thermal stability. W-LEDs comprising Na 2 Gd 0.6 Eu 1.4 Ti 3 O 10 showed bright white emission with a color rendering index (Ra) of 82, a color temperature of 2151 K, and Commission Internationale de I’Eclairage (CIE) color coordinates of (0.34, 0.37). The phosphor Na 2 Gd 0.6 Eu 1.4 Ti 3 O 10 is more suitable candidate for application in LEDs

UV-durable superhydrophobic textiles with UV-shielding properties by coating fibers with ZnO/SiO2 core/shell particles

Science.gov (United States)

Xue, Chao-Hua; Yin, Wei; Jia, Shun-Tian; Ma, Jian-Zhong

2011-10-01

ZnO/SiO2 core/shell particles were fabricated by successive coating of multilayer polyelectrolytes and then a SiO2 shell onto ZnO particles. The as-prepared ZnO/SiO2 core/shell particles were coated on poly(ethylene terephthalate) (PET) textiles, followed by hydrophobization with hexadecyltrimethoxysilane, to fabricate superhydrophobic surfaces with UV-shielding properties. Transmission electron microscopy and ζ potential analysis were employed to evidence the fabrication of ZnO/SiO2 core/shell particles. Scanning electron microscopy and thermal gravimetric analysis were conducted to investigate the surface morphologies of the textile and the coating of the fibers. Ultraviolet-visible spectrophotometry and contact angle measurement indicated that the incorporation of ZnO onto fibers imparted UV-blocking properties to the textile surface, while the coating of SiO2 shell on ZnO prohibited the photocatalytic degradation of hexadecyltrimethoxysilane by ZnO, making the as-treated PET textile surface show stable superhydrophobicity with good UV-shielding properties.

Temperature Mapping of Air Film-Cooled Thermal Barrier Coated Surfaces Using Cr-Doped GdAlO3 Phosphor Thermography

Science.gov (United States)

Eldridge, Jeffrey I.; Shyam, Vikram; Wroblewski, Adam C.; Zhu, Dongming; Cuy, Michael D.; Wolfe, Douglas E.

2016-01-01

It has been recently shown that the high luminescence intensity from a Cr-doped GdAlO3 (Cr:GdAlO3) thermographic phosphor enables non-rastered full-field temperature mapping of thermal barrier coating (TBC) surfaces to temperatures above 1000C. In this presentation, temperature mapping by Cr:GdAlO3 based phosphor thermometry of air film-cooled TBC-coated surfaces is demonstrated for both scaled-up cooling hole geometries as well as for actual components in a burner rig test environment. The effects of thermal background radiation and flame chemiluminescence on the measurements are investigated, and advantages of this method over infrared thermography as well as the limitations of this method for studying air film cooling are discussed.

Deep UV LEDs

Science.gov (United States)

Han, Jung; Amano, Hiroshi; Schowalter, Leo

2014-06-01

Deep ultraviolet (DUV) photons interact strongly with a broad range of chemical and biological molecules; compact DUV light sources could enable a wide range of applications in chemi/bio-sensing, sterilization, agriculture, and industrial curing. The much shorter wavelength also results in useful characteristics related to optical diffraction (for lithography) and scattering (non-line-of-sight communication). The family of III-N (AlGaInN) compound semiconductors offers a tunable energy gap from infrared to DUV. While InGaN-based blue light emitters have been the primary focus for the obvious application of solid state lighting, there is a growing interest in the development of efficient UV and DUV light-emitting devices. In the past few years we have witnessed an increasing investment from both government and industry sectors to further the state of DUV light-emitting devices. The contributions in Semiconductor Science and Technology 's special issue on DUV devices provide an up-to-date snapshot covering many relevant topics in this field. Given the expected importance of bulk AlN substrate in DUV technology, we are pleased to include a review article by Hartmann et al on the growth of AlN bulk crystal by physical vapour transport. The issue of polarization field within the deep ultraviolet LEDs is examined in the article by Braut et al. Several commercial companies provide useful updates in their development of DUV emitters, including Nichia (Fujioka et al ), Nitride Semiconductors (Muramoto et al ) and Sensor Electronic Technology (Shatalov et al ). We believe these articles will provide an excellent overview of the state of technology. The growth of AlGaN heterostructures by molecular beam epitaxy, in contrast to the common organo-metallic vapour phase epitaxy, is discussed by Ivanov et al. Since hexagonal boron nitride (BN) has received much attention as both a UV and a two-dimensional electronic material, we believe it serves readers well to include the

Luminescent characteristics of UV excited Sr{sub 0.5}Ca{sub 0.5}TiO{sub 3}: Pr{sup 3+} reddish-orange phosphor

Energy Technology Data Exchange (ETDEWEB)

Vidyadharan, Viji; Mohan P, Remya; Joseph, Cyriac; Unnikrishnan, N.V.; Biju, P.R., E-mail: prb.mgu@gmail.com

2016-02-15

Pr{sup 3+} doped Sr{sub 0.5}Ca{sub 0.5}TiO{sub 3} phosphors were synthesised by solid state reaction process. The structure, surface morphology and photoluminescence of the prepared phosphors were analysed using XRD, SEM and photoluminescence spectroscopy respectively. The XRD pattern confirmed orthorhombic perovskite structure of the Sr{sub 0.5}Ca{sub 0.5}TiO{sub 3}: x Pr{sup 3+} phosphor. Agglomeration of particles with irregular shapes is observed from the SEM images. The emission spectra of Sr{sub 0.5}Ca{sub 0.5}TiO{sub 3}: x Pr{sup 3+} phosphor shows the samples can be effectively excited with UV light at 336 nm and exhibit a strong reddish-orange emission at 611 nm. Concentration dependence of emission intensity shows concentration quenching effect on increasing Pr{sup 3+} concentration after x = 0.1 because of dipole–dipole interaction. Using Blasse's formula, critical distance for energy transfer was calculated. The CIE co-ordinates, CCT, colour purity and luminescence decay of the prepared phosphors were also calculated. These results offer the prepared phosphor as a suitable candidate for various photonic applications. - Highlights: • Sr{sub 0.5}Ca{sub 0.5}TiO{sub 3}: x Pr{sup 3+} perovskite structured phosphors were synthesized. • Under UV excitation, the PL spectra show strong reddish-orange emission. • The emission from {sup 3}P{sub J} levels of Pr{sup 3+} were absent due to the presence of IVCT band. • Concentration quenching due to dipole–dipole interaction was observed. • For x = 0.1, sample shows a maximum emission intensity with 91.7% colour purity.

Luminescent properties and energy transfer studies of color-tunable LuBO{sub 3}: Ce{sup 3+}/Tb{sup 3+}/Eu{sup 3+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xinguo, E-mail: sysuzxg@gmail.com [School of Pharmaceutical Sciences, Southern Medical University, Guangzhou 510515 (China); School of Chemistry and Chemical Engineering, Guangxi University, Nanning 530004 (China); Fu, Xionghui [Department of Chemistry, Jinan University, Guangzhou 510632 (China); Song, Jiahui [Shenzhou High School, Hengshui 053800 (China); Gong, Menglian [School of Chemistry and Chemical Engineering, Sun Yat-Sen University, Guangzhou 510275 (China)

2016-08-15

Highlights: • A series of color-tunable LuBO{sub 3}: Ce{sup 3+}/Tb{sup 3+}/Eu{sup 3+} phosphors were synthesized. • Phosphors exhibit strong blue/green/red emission under UV excitation. • The reason of high Tb{sup 3+} content required for Ce{sup 3+} → Tb{sup 3+} → Eu{sup 3+} energy transfer is unveiled. • Green and red LED prototypes were fabricated and characterized. - Abstract: A series of LuBO{sub 3}: Ce{sup 3+}/Tb{sup 3+}/Eu{sup 3+} phosphors were synthesized via solid state reaction. The Ce{sup 3+}/Tb{sup 3+} co-doped and Ce{sup 3+}/Tb{sup 3+}/Eu{sup 3+} tri-doped phosphors absorb near UV light through 4f-5d transitions of Ce{sup 3+}, followed by sensitized Tb{sup 3+} green and Eu{sup 3+} red emission. Decay curves investigations for samples with various Tb{sup 3+} and Eu{sup 3+} contents reveal the occurrence of Ce{sup 3+} → Tb{sup 3+} → Eu{sup 3+} energy transfer. It is found that due to relative low Tb{sup 3+} → Eu{sup 3+} energy transfer rate, a high Tb{sup 3+} content (>40%) is required for efficient Ce{sup 3+} → Tb{sup 3+} → Eu{sup 3+} energy transfer. Emission color of LuBO{sub 3}: Ce{sup 3+}, Tb{sup 3+}, Eu{sup 3+} varies from blue through green to red with Ce{sup 3+}/Tb{sup 3+}/Eu{sup 3+} ratio. The quantum efficiency of LuBO{sub 3}: Ce{sup 3+}, Tb{sup 3+} green phosphor and LuBO{sub 3}: Ce{sup 3+}, Tb{sup 3+}, Eu{sup 3+} red phosphor is 50% and 30%, respectively. Green and red LED prototypes were fabricated. The results show that the obtained phosphors are potential candidates as down-converted phosphors for NUV LEDs.

Correlation of Structure, Tunable Colors, and Lifetimes of (Sr, Ca, Ba)Al₂O₄:Eu2+, Dy3+ Phosphors.

Science.gov (United States)

Xie, Qidi; Li, Bowen; He, Xin; Zhang, Mei; Chen, Yan; Zeng, Qingguang

2017-10-18

(Sr, Ca, Ba)Al₂O₄:Eu 2+ , Dy 3+ phosphors were prepared via a high temperature solid-state reaction method. The correlation of phase structure, optical properties and lifetimes of the phosphors are investigated in this work. For the (Sr, Ca)Al₂O₄:Eu 2+ ,Dy 3+ phosphors, the different phase formation from monoclinic SrAl₂O₄ phase to hexagonal SrAl₂O₄ phase to monoclinic CaAl₂O₄ phase was observed when the Ca content increased. The emission color of SrAl₂O₄:Eu 2+ , Dy 3+ phosphors varied from green to blue. For the (Sr, Ba)Al₂O₄:Eu 2+ , Dy 3+ phosphors, different phase formation from the monoclinic SrAl₂O₄ phase to the hexagonal BaAl₂O₄ phase was observed, along with a shift of emission wavelength from 520 nm to 500 nm. More interestingly, the decay time of SrAl₂O₄:Eu 2+ , Dy 3+ changed due to the different phase formations. Lifetime can be dramatically shortened by the substitution of Sr 2+ with Ba 2+ cations, resulting in improving the performance of the alternating current light emitting diode (AC-LED). Finally, intense LEDs are successfully obtained by combining these phosphors with Ga(In)N near UV chips.

Tm3+ activated lanthanum phosphate: a blue PDP phosphor

International Nuclear Information System (INIS)

Rao, R.P.

2005-01-01

Plasma display panels (PDPs) are gaining attention due to their high performance and scalability as a medium for large format TVs. The performance and life of a PDP strongly depends upon the nature of phosphors. Currently, Eu 2+ activated barium magnesium aluminate (BAM) is being used as a blue component. Because of its low life, efforts are being made to explore new blue emitting phosphors. One of the alternatives to BAM is Tm 3+ activated lanthanum phosphate (LPTM) phosphor. LPTM phosphor samples are prepared by a solid-state as well as sol-gel process in presence of flux. The phosphor of the present investigation, having uniform and spherical shape particles in the range of 0.1-2 μm, is appropriate for thin phosphor screens required for PDP applications. It exhibits a narrow band emission in the blue region, peaking at 452 nm and also a number of narrow bands in the UV region when excited by 147 and 173 nm radiation from a xenon gas mixture. Various possible transitions responsible for UV and visible emission from Tm 3+ ion are presented. These phosphors also exhibit good color saturation and better stability when excited with VUV radiation. To achieve higher brightness, they are blended with other UV excited blue emitting phosphors such as BAM. Results related to morphology, excitation, after glow decay, emission and degradation of these phosphors in the powder form as well as in plasma display panels are presented and discussed

Enhanced orange-red emission by using Mo codoped in Ba2CaWO6: Eu3+, Li+ phosphor under near UV excitation

International Nuclear Information System (INIS)

Sun, Xiaoyuan; Hao, Zhendong; Li, Chunjie; He, Xiaoguang; Qi, Haiyan; Yu, Lijun; Luo, Yongshi; Zhang, Jiahua; Gao, Jiwei; Zhong, Ruixia

2013-01-01

The orange-red emitting phosphors Ba 2 Ca 0.9 Mo x W 1−x O 6 :Eu 3+ 0.05 , Li + 0.05 (x=0, 0.05, 0.1, 0.15, 0.2, 0.25, 0.5, 0.75, and 1.0) and Ba 2 Ca 1−2y Mo 0.2 W 0.8 O 6 :Eu 3+ y , Li + y (y=0.03, 0.05, 0.07, 0.1, and 0.15) were synthesized. The crystalline structure and photoluminescence properties of these phosphors were described. The strong orange-red emission of Eu 3+ ( 5 D 0 — 7 F 1 transition) at around 593 nm was observed. Addition of Mo strongly enhances the charge transfer band absorption in the near ultraviolet region that corresponds to near ultraviolet white light emitting diode. The dependence of photoluminescence intensities on Eu 3+ concentrations with optimal Mo concentration under 400 nm excitation was studied. The phosphor is considered to be a promising orange-red emitting phosphor for near ultraviolet GaN-based white light emitting diode. - Highlights: ► The samples form solid solutions when Mo is added into Ba 2 CaWO 6 : Eu 3+ , Li + phosphors. ► Addition of Mo in Ba 2 CaWO 6 : Eu 3+ , Li + shifts the PLE spectra maximum from UV region to near UV region. ► In Ba 2 CaMo x W 1−x O 6 :Eu 3+ , Li + , the most efficient concentrations occur at 0.1 and 0.2 for Eu and Mo.

Selecting the optimal synthesis parameters of InP/CdxZn1-xSe quantum dots for a hybrid remote phosphor white LED for general lighting applications.

Science.gov (United States)

Ryckaert, Jana; Correia, António; Tessier, Mickael D; Dupont, Dorian; Hens, Zeger; Hanselaer, Peter; Meuret, Youri

2017-11-27

Quantum dots can be used in white LEDs for lighting applications to fill the spectral gaps in the combined emission spectrum of the blue pumping LED and a broad band phosphor, in order to improve the source color rendering properties. Because quantum dots are low scattering materials, their use can also reduce the amount of backscattered light which can increase the overall efficiency of the white LED. The absorption spectrum and narrow emission spectrum of quantum dots can be easily tuned by altering their synthesis parameters. Due to the re-absorption events between the different luminescent materials and the light interaction with the LED package, determining the optimal quantum dot properties is a highly non-trivial task. In this paper we propose a methodology to select the optimal quantum dot to be combined with a broad band phosphor in order to realize a white LED with optimal luminous efficacy and CRI. The methodology is based on accurate and efficient simulations using the extended adding-doubling approach that take into account all the optical interactions. The method is elaborated for the specific case of a hybrid, remote phosphor white LED with YAG:Ce phosphor in combination with InP/CdxZn 1-x Se type quantum dots. The absorption and emission spectrum of the quantum dots are generated in function of three synthesis parameters (core size, shell size and cadmium fraction) by a semi-empirical 'quantum dot model' to include the continuous tunability of these spectra. The sufficiently fast simulations allow to scan the full parameter space consisting of these synthesis parameters and luminescent material concentrations in terms of CRI and efficacy. A conclusive visualization of the final performance allows to make a well-considered trade-off between these performance parameters. For the hybrid white remote phosphor LED with YAG:Ce and InP/CdxZn 1-x Se quantum dots a CRI Ra = 90 (with R9>50) and an overall efficacy of 110 lm/W is found.

An LED Approach for Measuring the Photocatalytic Breakdown of Crystal Violet Dye

Science.gov (United States)

Ryan, Robert E.; Underwood, Lauren W.; ONeal, Duane; Pagnutti, Mary; Davis, Bruce A.

2009-01-01

A simple technique to assess the reactivity of photocatalytic coatings sprayed onto transmissive glass surfaces was developed. This new method uses ultraviolet (UV) gallium nitride (GaN) light-emitting diodes (LEDs) to drive a photocatalytic reaction (the photocatalytic breakdown of a UV-resistant dye applied to a surface coated with the semiconductor titanium dioxide); and then a combination of a stabilized white light LED and a spectrometer to track the dye degradation as a function of time. Simple, standardized evaluation techniques that assess photocatalytic materials over a variety of environmental conditions, including illumination level, are not generally available and are greatly needed prior to in situ application of photocatalytic technologies. To date, much research pertaining to this aspect of photocatalysis has been limited and has focused primarily on laboratory experiments using mercury lamps. Mercury lamp illumination levels are difficult to control over large ranges and are temporally modulated by line power, limiting their use in helping to understand and predict how photocatalytic materials will behave in natural environmental settings and conditions. The methodology described here, using steady-state LEDs and time series spectroradiometric techniques, is a novel approach to explore the effect of UV light on the photocatalytic degradation of a UV resistant dye (crystal violet). GaN UV LED arrays, centered around 365 nm with an adjustable DC power supply, are used to create a small, spatially uniform light field where the steady state light level can be varied over three to four orders of magnitude. For this study, a set of glass microscope slides was custom coated with a thinly sprayed layer of photocatalytic titanium dioxide. Crystal violet was then applied to these titanium-dioxide coated slides and to uncoated control slides. The slides were then illuminated at various light levels from the dye side of the slide by the UV LED array. To monitor

Potential of Sm3+ doped LiSrVO4 nanophosphor to fill amber gap in LEDs

Science.gov (United States)

Biswas, P.; Kumar, Vinay; Sharma, Vishal; Bedyal, A. K.; Padha, Naresh; Swart, H. C.

2018-04-01

The LiSrVO4:Sm3+ phosphor powders were synthesized by the combustion method by varying the concentration of the Sm3+ ions from 0.25 mol% to 2.5 mol%. The powder X-ray diffraction (XRD) studies confirmed that the phosphors were crystallized as monoclinic structure belonging to space group P2/m and the transmission electron microscopy (TEM) revealed nanosized grains of the powders. The Fourier transform infrared studies (FTIR) established the formation of non-hygroscopic vanadate powders. The photoluminescence (PL) and diffused reflectance studies (DRS) were also carried out and discussed. Under 401 nm excitation, the optimized phosphor exhibited the characteristic 568, 600, 646 and 704 nm emissions of Sm3+ which corresponded to the orange-red (amber) color with (0.59, 0.41) Commission Internationale de' Eclairage (CIE) chromaticity coordinates. Concentration quenching of phosphor intensity on account of non-radiative energy transfer was ascribed to dipole-dipole interaction between activators. DRS study reveals that the host of the phosphor is a wide bandgap material which accommodates the dopant successfully. The present results signify that the LiSrVO4:Sm3+ phosphor can suitably be excited by the GaN family of UV-LEDs chips for efficient amber LEDs applications.

Trivalent europium-doped strontium molybdate red phosphors in white light-emitting diodes: Synthesis, photophysical properties and theoretical calculations

International Nuclear Information System (INIS)

Yang, W.-Q.; Liu, H.-G.; Liu, G.-K.; Lin, Y.; Gao, M.; Zhao, X.-Y.; Zheng, W.-C.; Chen, Y.; Xu, J.; Li, L.-Z.

2012-01-01

Eu 3+ -doped strontium molybdate red phosphors (Sr 1−x MoO 4 :Eu x (x = 0.01–0.2)) for white light-emitting diodes (LED) were synthesized by the solid-state reaction method. The fluorescent intensities of the as-prepared phosphors were remarkably improved. The excitation and emission spectra demonstrate that these phosphors can be effectively excited by the near-UV light (395 nm) and blue light (466 nm). Their emitted red light peaks are located at 613 nm, and the highest quantum yield value (η) of the as-grown red phosphor, which is 95.85%, is much higher than that of commercial red phosphor (77.53%). These red phosphors plus commercial yellow powers (1:10) were successfully packaged with the GaN-based blue chips on a piranha frame by epoxy resins. The encapsulated white LED lamps show high performance of the CIE chromaticity coordinates and color temperatures. Moreover, to explain the fluorescent spectra of these phosphors, a complete 3003 × 3003 energy matrix was successfully built by an effective operator Hamiltonian including free ion and crystal field interactions. For the first time, the fluorescent spectra for Eu 3+ ion at the tetragonal (S 4 ) Sr 2+ site of SrMoO 4 crystal were calculated from a complete diagonalization (of energy matrix) method. The fitting values are close to the experimental results.

Study on luminescence and thermal stability of blue-emitting Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+}phosphor for application in InGaN-based LEDs

Energy Technology Data Exchange (ETDEWEB)

Liu, Jie; Zhang, Zhi-Ming [State Key Laboratory Base of Eco-chemical Engineering, Laboratory of Inorganic Synthesis and Applied Chemistry, College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, Qingdao 266042 (China); Wu, Zhan-Chao, E-mail: wuzhan_chao@163.com [State Key Laboratory Base of Eco-chemical Engineering, Laboratory of Inorganic Synthesis and Applied Chemistry, College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, Qingdao 266042 (China); Wang, Fang-Fang [State Key Laboratory Base of Eco-chemical Engineering, Laboratory of Inorganic Synthesis and Applied Chemistry, College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, Qingdao 266042 (China); Li, Zhen-Jiang, E-mail: zjli126@126.com [State Key Laboratory Base of Eco-chemical Engineering, College of Sino-German Science and Technology, Qingdao University of Science and Technology, 53 Zhengzhou Road, Qingdao 266042, Shandong (China)

2017-07-15

Highlights: • A blue phosphor Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} was prepared at low temperature of 800 °C. • The broad excitation band of the phosphor matches well with NUV LED chips. • The phosphor shows high color purity and good color stability. • A bright blue-emitting LED was fabricated with this phosphor on an InGaN chip. - Abstract: A series of blue-emitting phosphors Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} were synthesized by traditional high temperature solid-state reaction method. The micro-morphology and photoluminescence properties of the phosphors were investigated. The Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} phosphors exhibit broad excitation spectra ranging from 250 to 420 nm, and an intense asymmetric blue emission band peaking at 435 nm. Two different Eu{sup 2+} emission centers in Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} phosphors were confirmed via their fluorescence properties. The concentration quenching mechanism, fluorescence lifetime and thermal stability of Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} phosphors were studied in detail. The thermal stability can be improved obviously by anion substitution. The CIE chromaticity coordinates of Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} phosphors with different Eu{sup 2+}-doped concentrations were calculated. A blue light-emitting diode was fabricated by combination of a 370 nm InGaN chip and the prepared phosphor Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+}. The present work suggests that Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} is a potential phosphor applied in InGaN-based LEDs.

Phosphor blends for high-CRI fluorescent lamps

Science.gov (United States)

Setlur, Anant Achyut [Niskayuna, NY; Srivastava, Alok Mani [Niskayuna, NY; Comanzo, Holly Ann [Niskayuna, NY; Manivannan, Venkatesan [Clifton Park, NY; Beers, William Winder [Chesterland, OH; Toth, Katalin [Pomaz, HU; Balazs, Laszlo D [Budapest, HU

2008-06-24

A phosphor blend comprises at least two phosphors each selected from one of the groups of phosphors that absorb UV electromagnetic radiation and emit in a region of visible light. The phosphor blend can be applied to a discharge gas radiation source to produce light sources having high color rendering index. A phosphor blend is advantageously includes the phosphor (Tb,Y,LuLa,Gd).sub.x(Al,Ga).sub.yO.sub.12:Ce.sup.3+, wherein x is in the range from about 2.8 to and including 3 and y is in the range from about 4 to and including 5.

Lens of controllable optical field with thin film metallic glasses for UV-LEDs.

Science.gov (United States)

Pan, C T; Chen, Y C; Lin, Po-Hung; Hsieh, C C; Hsu, F T; Lin, Po-Hsun; Chang, C M; Hsu, J H; Huang, J C

2014-06-16

In the exposure process of photolithography, a free-form lens is designed and fabricated for UV-LED (Ultraviolet Light-Emitting Diode). Thin film metallic glasses (TFMG) are adopted as UV reflection layers to enhance the irradiance and uniformity. The Polydimethylsiloxane (PDMS) with high transmittance is used as the lens material. The 3-D fast printing is attempted to make the mold of the lens. The results show that the average irradiance can be enhanced by 6.5~6.7%, and high uniformity of 85~86% can be obtained. Exposure on commercial thick photoresist using this UV-LED system shows 3~5% dimensional deviation, lower than the 6~8% deviation for commercial mercury lamp system. This current system shows promising potential to replace the conventional mercury exposure systems.

Luminescence Properties of Self-Activated Mm(VO4)2 (M = Mg, Ca, Sr, and Ba) Phosphors Synthesized by Solid-State Reaction Method.

Science.gov (United States)

Min, Xin; Huang, Zhaohui; Fang, Minghao; Liu, Yan'gai; Tang, Chao; Wu, Xiaowen

2016-04-01

In this paper, M3(VO4)2 (M = Mg, Ca, Sr, and Ba) self-activated phosphors were prepared by a solid-state reaction method at 1,000 °C for 5 h. The phase formation and micrographs were analyzed by X-ray diffraction and scanning electron microscopy. The Ca3(VO4)2 phosphor does not show any emission peaks under excitation with ultraviolet (UV) light. However, the M3(VO4)2 (M = Mg, Sr, and Ba) samples are effectively excited by UV light chips ranging from 200 nm to 400 nm and exhibit broad emission bands due to the charge transfer from the oxygen 2p orbital to the vacant 3d orbital of the vanadium in the VO4. The color of these phosphors changes from yellow to light blue via blue-green with increasing ionic radius from Mg to Sr to Ba. The luminescence lifetimes and quantum yield decrease with the increasing unit cell volume and V-V distance, in the order of Mg3(VO4)2 to Sr3(VO4)2 to Ba3(VO4)2. The emission intensity decreases with the increase of temperatures, but presents no color shift. This confirms that these self-activated M3(VO4)2 phosphors can be suggested as candidates of the single-phase phosphors for light using UV light emitting diodes (LEDs).

Crystal growth of electroluminescent ZnS:Cu,Cl phosphor and its TiO2 coating by sol-gel method for thick-film EL device

International Nuclear Information System (INIS)

Han, Sang-Do; Singh, Ishwar; Singh, Devender; Lee, You-He; Sharma, Gaytri; Han, Chi-Hwan

2005-01-01

Bigger-sized spherical particle of ZnS:Cu,Cl to be employed for electroluminescent (EL) device has been synthesized using a new eutectic mixture as flux. The best composition of the flux was the mixture of BaCl 2 .2H 2 O, MgCl 2 .6H 2 O and NaCl in the mole percentage ratio of 13.8:39.9:46.2 and when the total amount of the mixture was 6% of the total weight of ZnS. The phosphor was synthesized firing at higher temperatures in two steps. First step firing at 1150 deg. C gave the hexagonal phase of the ZnS phosphor particles. Low intensity ball-milling of the phosphor pastes in solvents converted hexagonal phase partially to the cubic phase of the phosphor, which is an essential step. Mixing with copper sulfate or copper(I) halides and magnesium chloride and then firing (second step) at 750 deg. C gave a phosphor with better luminescent characteristics and converting to almost 100% cubic phase. The phosphor particles having size >0.020 mm size were sieved and coated with TiO 2 made by sol-gel process using titanium(IV)-isopropoxide as a precursor. The phosphor particles were coated twice with the TiO 2 sol and finally calcined at 400 deg C in nitrogen atmosphere. The EL devices were fabricated with the synthesized phosphor using a screen-printing method

Spectral properties of Dy3+ doped ZnAl2O4 phosphor

Science.gov (United States)

Prakash, Ram; Kumar, Sandeep; Mahajan, Rubby; Khajuria, Pooja; Kumar, Vinay; Choudhary, R. J.; Phase, D. M.

2018-05-01

Herein, Dy3+ doped ZnAl2O4 phosphor was synthesized by the solution combustion method. The synthesized phosphor was characterized by X-ray diffraction (XRD), photoluminescence (PL) spectroscopy, UV-Vis spectroscopy and X-ray photoelectron spectroscopy (XPS). The phase purity of the phosphor was confirmed by the XRD studies that showed cubic symmetry of the synthesized phosphor. Under UV excitation (388 nm) the PL emission spectrum of the phosphor shows characteristic transition from the Dy3+ ion. A band gap of 5.2 eV was estimated from the diffused reflectance spectroscopy. The surface properties of the phosphor were studied using the X-ray photoelectron spectroscopy.

Photoluminescence properties and energy transfer of color tunable MgZn₂(PO₄)₂:Ce³⁺,Tb³⁺ phosphors.

Science.gov (United States)

Xu, Mengjiao; Wang, Luxiang; Jia, Dianzeng; Zhao, Hongyang

2015-11-21

A series of Ce(3+)/Tb(3+) co-doped MgZn2(PO4)2 phosphors have been synthesized by the co-precipitation method. Their structure, morphology, photoluminescence properties, decay lifetime, thermal stability and luminous efficiency were investigated. The possible energy transfer mechanism was proposed based on the experimental results and detailed luminescence spectra and decay curves of the phosphors. The critical distance between Ce(3+) and Tb(3+) ions was calculated by both the concentration quenching method and the spectral overlap method. The energy transfer mechanism from the Ce(3+) to Tb(3+) ion was determined to be dipole-quadrupole interaction, and the energy transfer efficiency was 85%. By utilizing the principle of energy transfer and appropriate tuning of Ce(3+)/Tb(3+) contents, the emission color of the obtained phosphors can be tuned from blue to green light. The MgZn2(PO4)2:Ce(3+),Tb(3+) phosphor is proved to be a promising UV-convertible material capable of green light emitting in UV-LEDs due to its excellent thermal stability and luminescence properties.

Spectroscopic properties of Eu{sup 3+}:KLa(WO{sub 4}){sub 2} novel red phosphors

Energy Technology Data Exchange (ETDEWEB)

Rasu, K. Kavi; Balaji, D.; Babu, S. Moorthy, E-mail: babusm@yahoo.com

2016-02-15

Eu{sup 3+}:KLa(WO{sub 4}){sub 2} (Eu:KLW) phosphors were prepared through Pechini type sol–gel method. Low temperature synthesis was achieved through polyesterification between citric acid and ethylene glycol during the growth procedure. The properties of phosphors were analysed using X-ray diffractogram (XRD), scanning electron microscopy (SEM), Raman and luminescence spectroscopy. An effective energy transfer from the tungstate matrix to the activator Eu{sup 3+} was observed. Intense red emission in Eu:KLW phosphors was observed while excited with f–f transitions of Eu{sup 3+}. The Judd–Ofelt (J–O) intensity parameters Ω{sub 2} and Ω{sub 4} were obtained from the emission intensities of {sup 5}D{sub 0}→{sup 7}F{sub 2},{sub 4,} respectively by taking the magnetic dipole {sup 5}D{sub 0}→{sup 7}F{sub 1} emission band intensity as reference. The CIE colour co-ordinates of the Eu:KLW red phosphors was calculated (x=0.650, y=0.348), which are close to NTSC standard values. - Highlights: • Eu:KLW phosphors were synthesized by pechini type sol–gel method. • Structural, morphological, vibrational and luminescence properties were well investigation. • Eu{sup 3+}:KLa(WO{sub 4}){sub 2} phosphors has strong red emission at about 615 nm ({sup 5}D{sub 0}→{sup 7}F{sub 2}) under the excitation of near UV and blue LEDs regions. • Decay measurement and Judd–Ofelt parameter were calculated and dicussed. • These phosphors can serve as a potential candidate for red source for White LEDs application.

Combustion synthesis and optical properties of Oxy-borate phosphors YCa4O(BO3)3:RE3+ (RE = Eu3+, Tb3+) under UV, VUV excitation

International Nuclear Information System (INIS)

Ingle, J.T.; Gawande, A.B.; Sonekar, R.P.; Omanwar, S.K.; Wang, Yuhua; Zhao, Lei

2014-01-01

Graphical abstract: VUV Photoluminescence of YCa 4 O(BO 3 ) 3 : Eu 3+ and YCa 4 O(BO 3 ) 3 : Tb 3+ for PDPs applications. Highlights: • Inorganic Oxy-borate phosphors YCa 4 O(BO 3 ) 3 :Eu 3+ ,Tb 3+ was synthesized by novel solution combustion synthesis. • This single host produces efficient and intense Red and Green color for display applications. • Good agreement with CIE co-ordinates as prescribes by NTCL, for flat panel, PDP display color. • Synthesized materials were characterized using powder XRD, FE-SEM, UV and VUV Spectophotometer. -- Abstract: The inorganic Oxy-borate host phosphors YCa 4 O(BO 3 ) 3 :RE 3+ (RE = Eu 3+ ,Tb 3+ ) were synthesized by a novel solution combustion technique. The synthesis is based on the exothermic reaction between the fuel (Urea) and Oxidizer (Ammonium nitrate). The heat generated in reaction is use for auto combustion of precursors. The structures of the prepared samples were confirmed by powder XRD technique. The photoluminescence properties of the powder samples were investigated under UV and VUV excitation; “The phosphor YCa 4 O(BO 3 ) 3 :Eu 3+ and YCa 4 O(BO 3 ) 3 :Tb 3+ shows strong absorption in UV and VUV region and exhibits intense red and green emission upon excited by 254 nm UV and 147 nm VUV radiation”

A Novel Orange-Red Emitting ZnB4O7:Eu3+ Phosphor with Urchin-Like Nanostructure

Directory of Open Access Journals (Sweden)

Hom Nath Luitel

2015-01-01

Full Text Available A novel phosphor, ZnB4O7:Eu3+, with urchin-like structure consisting of radially arranged high density nanorods was successfully synthesized by hydrothermal process at 150°C for 24 h. The nanorods were measured from 200 to 400 nm in diameter and several µm in length. The urchins were few µm to 40 µm in diameter. The ZnB4O7:Eu3+ phosphors were efficiently excited by ultraviolet (UV ~ 254 nm to visible light of ~ 220 to 450 nm and exhibited intense orange-red emission consisting of main peaks at 590, 615, and 695 nm due to the charge transfer in the host and f→f transitions (5D0 to 7F1,2,4 of the Eu3+ ions. Effect of the Eu3+ ions concentration on the photoluminescence (PL emission intensity was investigated and it was found that 5 at% Eu3+ is the optimum concentration. Meanwhile, the concentration quenching mechanism was discussed. The key parameters, such as temperature dependent PL and CIE values of ZnB4O7:Eu3+ phosphors, were studied. The ZnB4O7:Eu3+ phosphor exhibited good thermal stability and better absorption cross section compared to the commercial Y2O2S:Eu3+ phosphor. All these characteristics indicate that the phosphor will be a potential candidate for the UV based white LEDs.

240 nm UV LEDs for LISA test mass charge control

Science.gov (United States)

Olatunde, Taiwo; Shelley, Ryan; Chilton, Andrew; Serra, Paul; Ciani, Giacomo; Mueller, Guido; Conklin, John

2015-05-01

Test Masses inside the LISA Gravitational Reference Sensor must maintain almost pure geodesic motion for gravitational waves to be successfully detected. LISA requires residual test mass accelerations below 3 fm/s2/√Hz at all frequencies between 0.1 and 3 mHz. One of the well-known noise sources is associated with the charges on the test masses which couple to stray electrical potentials and external electromagnetic fields. LISA Pathfinder will use Hg-discharge lamps emitting mostly around 254 nm to discharge the test masses via photoemission in its 2015/16 flight. A future LISA mission launched around 2030 will likely replace the lamps with newer UV-LEDs. Presented here is a preliminary study of the effectiveness of charge control using latest generation UV-LEDs which produce light at 240 nm with energy above the work function of pure Au. Their lower mass, better power efficiency and small size make them an ideal replacement for Hg lamps.

240 nm UV LEDs for LISA test mass charge control

International Nuclear Information System (INIS)

Olatunde, Taiwo; Shelley, Ryan; Chilton, Andrew; Serra, Paul; Ciani, Giacomo; Mueller, Guido; Conklin, John

2015-01-01

Test Masses inside the LISA Gravitational Reference Sensor must maintain almost pure geodesic motion for gravitational waves to be successfully detected. LISA requires residual test mass accelerations below 3 fm/s 2 /√Hz at all frequencies between 0.1 and 3 mHz. One of the well-known noise sources is associated with the charges on the test masses which couple to stray electrical potentials and external electromagnetic fields. LISA Pathfinder will use Hg-discharge lamps emitting mostly around 254 nm to discharge the test masses via photoemission in its 2015/16 flight. A future LISA mission launched around 2030 will likely replace the lamps with newer UV-LEDs. Presented here is a preliminary study of the effectiveness of charge control using latest generation UV-LEDs which produce light at 240 nm with energy above the work function of pure Au. Their lower mass, better power efficiency and small size make them an ideal replacement for Hg lamps. (paper)

Single-phased CaAl2Si2O8:Tm3+, Dy3+ white-light phosphors under ultraviolet excitation

International Nuclear Information System (INIS)

Yang, Penghui; Yu, Xue; Xu, Xuhui; Jiang, Tingming; Yu, Hongling; Zhou, Dacheng; Yang, Zhengwen; Song, Zhiguo; Qiu, Jianbei

2013-01-01

A novel white-light-emitting phosphor CaAl 2 Si 2 O 8 :Tm, Dy was synthesized in ambient atmosphere by solid-state reaction. The energy transfer from Tm 3+ to Dy 3+ ions via a dipole–quadrupole reaction was observed and investigated. Upon UV excitation, white light emission was achieved by integrating a blue emission band located at 455 nm and an orange one located at 574 nm attributed to Tm 3+ and Dy 3+ ions, respectively. In addition, the energy-transfer efficiency and critical distance were calculated. Results suggested that the phosphor might be promising as a single-phased white-light-emitting phosphor for UV white-light LED. - Graphical abstract: The results indicate the existence of energy transfer from Tm 3+ to Dy 3+ . By tuning the concentration of Dy 3+ , single-phased white light can be realized. - Highlights: ► Energy transfer from Tm 3+ to Dy 3+ was investigated. ► Color tunable from blue to white can be achieved. ► White light can be realized in CaAl 2 Si 2 O 8 :Tm 3+ , Dy 3+ phosphor

Combinatorial search for green and blue phosphors of high thermal stabilities under UV excitation based on the K(Sr1-x-y)PO4:Tb3+ xEu2+y system.

Science.gov (United States)

Chan, Ting-Shan; Liu, Yao-Min; Liu, Ru-Shi

2008-01-01

The present investigation aims at the synthesis of KSr 1-x-y PO 4:Tb(3+) x Eu(2+) y phosphors using the combinatorial chemistry method. We have developed square-type arrays consisting of 121 compositions to investigate the optimum composition and luminescence properties of KSrPO 4 host matrix under 365 nm ultraviolet (UV) light. The optimized compositions of phosphors were found to be KSr 0.93PO 4:Tb(3+) 0.07 (green) and KSr 0.995PO 4:Eu(2+) 0.005 (blue). These phosphors showed good thermal luminescence stability better than commercially available YAG:Ce at temperature above 200 degrees C. The result indicates that the KSr 1-x-y PO 4:Tb(3+) x Eu (2+)y can be potentially useful as a UV radiation-converting phosphor for light-emitting diodes.

Ground testing and flight demonstration of charge management of insulated test masses using UV-LED electron photoemission

Science.gov (United States)

Saraf, Shailendhar; Buchman, Sasha; Balakrishnan, Karthik; Lui, Chin Yang; Soulage, Michael; Faied, Dohy; Hanson, John; Ling, Kuok; Jaroux, Belgacem; Suwaidan, Badr Al; AlRashed, Abdullah; Al-Nassban, Badr; Alaqeel, Faisal; Harbi, Mohammed Al; Salamah, Badr Bin; Othman, Mohammed Bin; Qasim, Bandar Bin; Alfauwaz, Abdulrahman; Al-Majed, Mohammed; DeBra, Daniel; Byer, Robert

2016-12-01

The UV-LED mission demonstrates the precise control of the potential of electrically isolated test masses. Test mass charge control is essential for the operation of space accelerometers and drag-free sensors which are at the core of geodesy, aeronomy and precision navigation missions as well as gravitational wave experiments and observatories. Charge management using photoelectrons generated by the 254 nm UV line of Hg was first demonstrated on Gravity Probe B and is presently part of the LISA Pathfinder technology demonstration. The UV-LED mission and prior ground testing demonstrates that AlGaN UVLEDs operating at 255 nm are superior to Hg lamps because of their smaller size, lower power draw, higher dynamic range, and higher control authority. We show laboratory data demonstrating the effectiveness and survivability of the UV-LED devices and performance of the charge management system. We also show flight data from a small satellite experiment that was one of the payloads on KACST’s SaudiSat-4 mission that demonstrates ‘AC charge control’ (UV-LEDs and bias are AC modulated with adjustable relative phase) between a spherical test mass and its housing. The result of the mission brings the UV-LED device Technology Readiness Level (TRL) to TRL-9 and the charge management system to TRL-7. We demonstrate the ability to control the test mass potential on an 89 mm diameter spherical test mass over a 20 mm gap in a drag-free system configuration, with potential measured using an ultra-high impedance contact probe. Finally, the key electrical and optical characteristics of the UV-LEDs showed less than 7.5% change in performance after 12 months in orbit.

Final Scientific/Technical Report "Arc Tube Coating System for Color Consistency"

Energy Technology Data Exchange (ETDEWEB)

Buelow, Roger [Energy Focus, Inc., Solon, OH (United States); Jenson, Chris [Energy Focus, Inc., Solon, OH (United States); Kazenski, Keith [Energy Focus, Inc., Solon, OH (United States)

2013-03-21

DOE has enabled the use of coating materials using low cost application methods on light sources to positively affect the output of those sources. The coatings and light source combinations have shown increased lumen output of LED fixtures (1.5%-2.0%), LED arrays (1.4%) and LED powered remote phosphor systems Philips L-Prize lamp (0.9%). We have also demonstrated lifetime enhancements (3000 hrs vs 8000 hrs) and shifting to higher CRI (51 to 65) in metal halide high intensity discharge lamps with metal oxide coatings. The coatings on LEDs and LED products are significant as the market is moving increasingly more towards LED technology. Enhancements in LED performance are demonstrated in this work through the use of available materials and low cost application processes. EFOI used low refractive index fluoropolymers and low cost dipping processes for application of the material to surfaces related to light transmission of LEDs and LED products. Materials included Teflon AF, an amorphous fluorinated polymer and fluorinated acrylic monomers. The DOE SSL Roadmap sets goals for LED performance moving into the future. EFOI's coating technology is a means to shift the performance curve for LEDs. This is not limited to one type of LED, but is relevant across LED technologies. The metal halide work included the use of sol-gel solutions resulting in silicon dioxide and titanium dioxide coatings on the quartz substrates of the metal halide arc tubes. The coatings were applied using low cost dipping processes.

Synthesis and luminescence properties of Ce{sup 3+}-doped Y{sub 3}Al{sub 3.5}Ga{sub 1.5}O{sub 12} green phosphor for white LEDs

Energy Technology Data Exchange (ETDEWEB)

Qiang, Yaochun [Fujian Key Laboratory of Advanced Materials, Department of Materials Science and Engineering, College of Materials, Xiamen University, Xiamen 361005 (China); Yu, Yuxi, E-mail: yu_heart@xmu.edu.cn [Fujian Key Laboratory of Advanced Materials, Department of Materials Science and Engineering, College of Materials, Xiamen University, Xiamen 361005 (China); Chen, Guolong [Fujian Engineering Research Center for Solid-state Lighting, Department of Electronic Science, Xiamen University, Xiamen 361005 (China); Fang, Jiyu [Advanced Materials Processing and Analysis Center, Department of Materials Science and Engineering, University of Central Florida, Orlando, FL 32816 (United States)

2016-04-15

A series of Ce{sup 3+}-doped Y{sub 3}Al{sub 3.5}Ga{sub 1.5}O{sub 12} green phosphors were successfully synthesized by a solid-state reaction method. The microstructure, morphology, luminescence spectra, luminescence quantum yield (QY) and thermal stability of the phosphor were investigated. The critical concentration of Ce{sup 3+} ions in Y{sub 3−m}Al{sub 3.5}Ga{sub 1.5}O{sub 12}:mCe{sup 3+} is m=0.06. The QY of Y{sub 2.94}Al{sub 3.5}Ga{sub 1.5}O{sub 12}:0.06Ce{sup 3+} phosphor is as high as 94% under excitation at 450 nm and its luminescence intensity at 150 °C still maintains 90% of that measured at 25 °C, which are just a little worse than those of commercial Lu{sub 3}Al{sub 5}O{sub 12}:Ce{sup 3+} green phosphor but much better than those of commercial (Sr,Ba){sub 2}SiO{sub 4}:Eu{sup 2+} green phosphor. A white LED lamp was fabricated by employing Y{sub 2.94}Al{sub 3.5}Ga{sub 1.5}O{sub 12}:0.06Ce{sup 3+} as a green phosphor and commercial (Ca,Sr)AlSiN{sub 3}:Eu{sup 2+} as a red phosphor (628 nm), its Ra value, correlated color temperature (CCT), CIE1931 chromaticity coordinates and luminous efficiency is 84, 3081 K, (x=0.4369, y=0.4142) and 102 lm/W, respectively. The experimental results demonstrate that Y{sub 2.94}Al{sub 3.5}Ga{sub 1.5}O{sub 12}:0.06Ce{sup 3+} is a promising green phosphor not only can be used for high color rendering index white LEDs but also for high-power white LEDs.

Using AlN-Coated Heat Sink to Improve the Heat Dissipation of LED Packages

Directory of Open Access Journals (Sweden)

Jean Ming-Der

2016-01-01

Full Text Available This study optimizes aluminum nitride (AlN ceramics, in order to enhance the thermal performance of light-emitting diode (LED packages. AlN coatings are grown on copper/ aluminum substrates as a heat interface material, using an electrostatic spraying process. The effect of the deposition parameters on the coatings is determined. The thermal performance of AlN coated Cu/Al substrates is evaluated in terms of the heat dissipated and compared by measuring the LED case temperature. The structure and properties of the coating are also examined a scanning electron microscopy (SEM. In sum, the thermal performance of the LED is increased and good heat resistance characteristics are obtained. The results show that using AlN ceramic coating on a copper/aluminum substrate increases the thermal performance.

Synthesis of Y{sub 2}O{sub 3}:(Li,Eu) films using phosphor powders coated with SiO{sub 2} nano particles

Energy Technology Data Exchange (ETDEWEB)

Kim, In-Gyu; Park, Sangmoon [Center for Green Fusion Technology and Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of); Kang, Seong-Gu [Department of Chemical Engineering, Hoseo University, Chungnam 336-795 (Korea, Republic of); Park, Jung-Chul, E-mail: parkjc@silla.ac.k [Center for Green Fusion Technology and Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of)

2010-08-15

Y{sub 1.9-x}Li{sub 0.1}Eu{sub x}O{sub 3} (x=0.02, 0.05, 0.08, and 0.12) films were fabricated by spin-coating method. A colloidal silica suspension with Y{sub 1.9-x}Li{sub 0.1}Eu{sub x}O{sub 3} phosphor powder was exploited to obtain the highly stable and effective luminescent films onto the glass substrate. After heating as-prepared Y{sub 1.9-x}Li{sub 0.1}Eu{sub x}O{sub 3} films at 700 {sup o}C for 1 h, the phosphor films exhibit a high luminescent brightness as well as a strong adhesiveness on the glass substrate. The emission spectra of spin-coated and pulse-laser deposited Y{sub 1.82}Li{sub 0.1}Eu{sub 0.08}O{sub 3} films were compared. The cathodoluminescence of the phosphor films was carried out at the anode voltage 1 kV.

Phosphors for solid-state lighting: New systems, deeper understanding

Science.gov (United States)

Denault, Kristin Ashley

+; Li + is red-shifted from the near-UV to blue with compositional changes. The red-shifted photoluminescent quantum yield also increases when Sr is substituted for Ba in these compounds. The end member Ba9Y2Si 6O24:Ce 3+ was identified as an efficient blue-green phosphor with high thermal stability of the luminescence, viable for near-UV LED excitation. An efficient emission, with a quantum yield of ≈60%, covers a broad portion of the visible spectrum leading to the observed blue-green color. The emission of this compound can be red-shifted via the solid-solution Ba9(Y 1-ySc y) 2Si6O24:Ce3+. We then explore the structure-composition relationships and optical properties in newly developed cerium-substituted (Sr,Ba)3(Y,La)(BO3) 3 borate phosphors. Examination of the coordination environment of the Ce3+ active site polyhedra coupled with low-temperature photoluminescence reveals three distinct excitation bands corresponding to Ce3+ located on three distinct crystallographic sites. Comparing the position of these excitation bands with crystal field splitting effects due to changes in polyhedral volumes and distortions suggests an assignment of the three excitation bands. These compounds are efficiently excited by UV light with blue emission, the most efficient compound determined to be Sr3La(BO 3)3:Ce3+,Na + with a quantum yield of 50%. A data-driven discovery of energy materials then reveals the efficient BaM2Si3O10:Eu2+ (M = Sc, Lu) phosphors with UV-to-blue and UV-to-blue-green phosphors. Interestingly, substituting Eu2+ in the Lu3+ containing material produces two emission peaks, at low temperature, as allowed by two substitution sites. The photoluminescence of the Sc3+ compound is robust at high temperature, while the Lu-analogue has a large decrease of its room temperature intensity. The decrease in emission intensity is explained as stemming from charge transfer quenching due to the short distances separating the luminescent centers on the Lu3+ substitution site

Surface coatings of unsaturated polyester resin Kamper wood (Dry obalan ops spp.) by using UV radiation

International Nuclear Information System (INIS)

Sugiarto Danu; Yusuf Sudo Hadi; Novi Eka Putri

1999-01-01

Kamper wood (Dryobalanops spp.) has high contribution in wood working industry and most of them need surface coating process. Radiation curing of surface coating, especially the use of ultra-violet (UV) light have potential to give contribution in the wood finishing. The experiment on surface coating of kamper wood has been conducted by using UV-radiation. Unsaturated polyester resin with the commercial name of Yucalac type 157 was used as coating materials after being added with styrene monomer, some fillers and radical photoinitiator of 2-hydroxy-2-2-methyl-l- phenyl propanone. Four photoinitiator concentration levels of 1.5 ; 2 ; 2.5 and 3 % by weight of resin were used. The coating materials were coated onto the wood panel samples by using high pressure sprayer. The wood samples were then exposed to irradiation by using 80 Watts/cm UV-source with variable conveyor speed of 3 ; 4 ; 5 and 5.8 m/min. Formulation of coating materials, pendulum hardness, adhesion, and gloss of cured films were evaluated

Optimization of synthesis technique and luminescent properties in Eu{sup 3+}-activated NaCaPO{sub 4} phosphor for solid state lighting applications

Energy Technology Data Exchange (ETDEWEB)

Ratnam, B.V. [Department of Physics, Changwon National University, Changwon 51140 (Korea, Republic of); Sahu, Mukesh K.; Vishwakarma, Amit K.; Jha, Kaushal [Luminescent Materials Research Lab (LMRL), Department of Applied Physics, Delhi Technological University, Delhi 110042 (India); Woo, Hyun-Joo [Department of Physics, Changwon National University, Changwon 51140 (Korea, Republic of); Jang, Kiwan, E-mail: kwjang@changwon.ac.kr [Department of Physics, Changwon National University, Changwon 51140 (Korea, Republic of); Jayasimhadri, M., E-mail: jayaphysics@yahoo.com [Luminescent Materials Research Lab (LMRL), Department of Applied Physics, Delhi Technological University, Delhi 110042 (India)

2017-05-15

Europium activated NaCaPO{sub 4} phosphor has been synthesized by various synthesis techniques such as solid-state reaction (SSR), molten salt synthesis (MSS) and sol-gel combustion (SGC) method to optimize the synthesis procedure. The comparative investigations of structural and luminescent properties have been studied to know the best synthesis method. The XRD patterns and Rietveld refinement analysis of the synthesized phosphors confirmed the single phase orthorhombic structure of NaCaPO{sub 4}. Excitation spectra indicate the strong absorption in near ultraviolet (n-UV) region and the emission spectra exhibit strong emission band at 595 nm corresponds to {sup 5}D{sub 0}→{sup 7}F{sub 1} transition under n-UV (λ{sub ex}=392 nm) excitation. The SGC route synthesized phosphor exhibit intense emission than that of the SSR and MSS method. Therefore, the effect of dopant (Eu{sup 3+}) concentration on the emission intensity and concentration quenching mechanism has been discussed in detail for the Eu{sup 3+} doped NaCaPO{sub 4} phosphor synthesized by SGC method. The CIE chromaticity coordinates have been calculated for the phosphors synthesized by SSR, MSS and SGC methods to reveal the emitting color and also to know the utility of this phosphor for white LEDs.

TL process in europium doped alkaline earth sulphate phosphors- a review

International Nuclear Information System (INIS)

Bhatt, B.C.

2003-01-01

CaSO 4 doped with the rare earth (RE) ion dysprosium or thulium is used routinely as a thermoluminescent dosimeter (TLD) to monitor personal exposure to x- and γ-radiation. The CaSO 4 :Eu phosphor is potentially important for radio photoluminescence (RPL) and ultraviolet (UV) dosimetry. Eu 3+ → Eu 2+ conversion is suggested to play a pivotal role in UV and γ-ray induced thermoluminescence. However, there is disagreement among different workers on the mechanism of gamma and UV induced TL in this phosphor system. This paper will review the work reported on CaSO 4 :Eu and make effects to project overall picture on this phosphor system. (author)

Intrinsic thermoluminescence of NaCl:Tl in UV dosimetry

International Nuclear Information System (INIS)

Barghare, S.P.; Joshi, R.V.; Joshi, T.R.; Kathuria, S.P.

1982-01-01

NaCl:Tl(T) phosphor is found to have high intrinsic thermoluminescence (TL) sensitivity to 253.7 nm UV-radiation. The dosimetric glow peak II grows sublinearly with increase in UV dose in the range 10 3 to 10 6 JM -2 . The other requirements of an efficient dosimeter material such as high storage stability, matching of the spectral response of detector tube and TL-emission from phosphor, reproducibility, desirable size and shape, easy availability in powder, pellet and crystal forms at cheaper rates, and repeated re-usability of the same phosphor without much difficulty, etc., are additional factors which strengthen the claim of NaCl:Tl(T) phosphor as UV dosimetric material. It is proposed that present NaCl:Tl(T) material is suitable TL-phosphor for UV dosimetry in the range 10 3 to 10 6 JM -2 . (author)

Ultraviolet excitation of remote phosphor with symmetrical illumination used in dual-sided liquid-crystal display.

Science.gov (United States)

Huang, Hsin-Tao; Tsai, Chuang-Chuang; Huang, Yi-Pai

2010-08-01

The UV-excited flat lighting (UFL) technique differs from conventional fluorescent lamp or LED illumination. It involves using a remote phosphor film to convert the wavelength of UV light to visible light, achieving high brightness and planar and uniform illumination. In particular, UFL can accomplish compact size, low power consumption, and symmetrical dual-sided illumination. Additionally, UFL utilizes a thermal radiation mechanism to release the large amount of heat that is generated upon illumination without thermal accumulation. These characteristics of the UFL technique can motivate a wide range of lighting applications in thin-film transistor LCD backlighting or general lighting.

Ultraviolet dosimetry using thermoluminescent phosphors - an update

International Nuclear Information System (INIS)

Nagpal, J.S.

1998-04-01

Intrinsic response of various thermoluminescent (TL) materials such as CaSO 4 (Dy, Eu, Mn, Sm, Tb, or Tm), LiF (Mg, Cu, P), Mg 2 SiO 4 :Tb, CaF 2 :Dy, CaF 2 :Tb, ThO 2 :Tb and Al 2 O 3 (Si, Ti); cathodoluminescent phosphors Y 3 Al 5 O 12 :Ce, Y 3 Al 5 O 12 :Tb and Y(V,P)O 4 :Eu; and fluorescent lamp phosphors calcium halophosphate (Mn,Sb) and Ce Mg aluminate (Eu, Tb) to ultraviolet (UV) radiations has been studied. Intrinsic TL response of most of the phosphors is rate (radiant flux) dependent. For the first time, UV response of the materials is reported for a fixed total radiant energy (total UV dose), at a single radiant flux (260 μW.cm -2 ), for an appropriate comparison. A wide range of UV sensitivity is observed. Studies conducted using UV radiation from two unfiltered low pressure mercury lamps show significant differences in glow curves, as compared to those obtained with nearly monochromatic UV radiations. Photons of wavelength 365 nm induce bleaching of TL induced by 254 nm photons, in most of the materials. Sequential/tandem exposures to 254 nm and 365 nm photons have yielded new but alarming results in CaF 2 :Tb. Preferential induction and bleaching of specific TL glow peaks by 365 nm and 254 nm photons are interesting characteristics discovered in CaSO 4 :Eu. Photoluminescence studies of Tb 3+ and Eu 3+ activated phosphors have augmented the inferences drawn from the bleaching effects produced by 365 nm photons. Earlier work carried out on phototransferred thermoluminescence of CaSO 4 :Dy-teflon dosimeters, TLD-100, Mg 2 SiO 4 :Tb and Al 2 O 3 (Si,Ti) has also been reviewed. (author)

Enhanced protective properties and UV stability of epoxy/graphene nanocomposite coating on stainless steel

Directory of Open Access Journals (Sweden)

H. Alhumade

2016-12-01

Full Text Available Epoxy-Graphene (E/G nanocomposites with different loading of graphene were prepared via in situ prepolymerization and evaluated as protective coating for Stainless Steel 304 (SS304. The prepolymer composites were spin coated on SS304 substrates and thermally cured. Transmission Electron Microscopy (TEM and Scanning Electron Microscopy (SEM were utilized to examine the dispersion of graphene in the epoxy matrix. Epoxy and E/G nanocomposites were characterized using X-ray diffraction (XRD and Fourier Transform Infrared (FTIR techniques and the thermal behavior of the prepared coatings is analyzed using Thermogravimetric analysis (TGA and Differential scanning calorimetry (DSC. The corrosion protection properties of the prepared coatings were evaluated using Electrochemical Impedance Spectroscopy (EIS and Cyclic Voltammetry (CV measurements. In addition to corrosion mitigation properties, the long-term adhesion performance of the coatings was evaluated by measuring the adhesion of the coatings to the SS304 substrate after 60 days of exposure to 3.5 wt% NaCl medium. The effects of graphene loading on the impact resistance, flexibility, and UV stability of the coating are analyzed and discussed. SEM was utilized to evaluate post adhesion and UV stability results. The results indicate that very low graphene loading up to 0.5 wt % significantly enhances the corrosion protection, UV stability, and impact resistance of epoxy coatings.

Ground testing and flight demonstration of charge management of insulated test masses using UV-LED electron photoemission

International Nuclear Information System (INIS)

Saraf, Shailendhar; Buchman, Sasha; Balakrishnan, Karthik; Lui, Chin Yang; Alfauwaz, Abdulrahman; DeBra, Daniel; Soulage, Michael; Faied, Dohy; Hanson, John; Ling, Kuok; Jaroux, Belgacem; Suwaidan, Badr Al; AlRashed, Abdullah; Al-Nassban, Badr; Alaqeel, Faisal; Harbi, Mohammed Al; Salamah, Badr Bin; Othman, Mohammed Bin; Qasim, Bandar Bin; Al-Majed, Mohammed

2016-01-01

The UV-LED mission demonstrates the precise control of the potential of electrically isolated test masses. Test mass charge control is essential for the operation of space accelerometers and drag-free sensors which are at the core of geodesy, aeronomy and precision navigation missions as well as gravitational wave experiments and observatories. Charge management using photoelectrons generated by the 254 nm UV line of Hg was first demonstrated on Gravity Probe B and is presently part of the LISA Pathfinder technology demonstration. The UV-LED mission and prior ground testing demonstrates that AlGaN UVLEDs operating at 255 nm are superior to Hg lamps because of their smaller size, lower power draw, higher dynamic range, and higher control authority. We show laboratory data demonstrating the effectiveness and survivability of the UV-LED devices and performance of the charge management system. We also show flight data from a small satellite experiment that was one of the payloads on KACST’s SaudiSat-4 mission that demonstrates ‘AC charge control’ (UV-LEDs and bias are AC modulated with adjustable relative phase) between a spherical test mass and its housing. The result of the mission brings the UV-LED device Technology Readiness Level (TRL) to TRL-9 and the charge management system to TRL-7. We demonstrate the ability to control the test mass potential on an 89 mm diameter spherical test mass over a 20 mm gap in a drag-free system configuration, with potential measured using an ultra-high impedance contact probe. Finally, the key electrical and optical characteristics of the UV-LEDs showed less than 7.5% change in performance after 12 months in orbit. (paper)

Investigation of vacuum deposited hybrid coatings of protic organic UV absorbers embedded in a silica matrix used for the UV protection of Polycarbonate glazing

OpenAIRE

Weber, C.; Schulz, U.; Mühlig, C.; Kaiser, N.; Tünnermann, A.

2016-01-01

A study of vacuum-deposited organic-inorganic hybrid coatings for UV protection of polycarbonate is presented. UV-absorbing compounds, which are commonly used for polycarbonate, were embedded in a silica matrix by thermal co-evaporation under high vacuum. In addition to the optical properties of the coatings, the influence of the silica network on the organic UV absorber and the stability of the intramolecular hydrogen bond (IMHB) are discussed. A model is presented to show the interaction be...

Monitoring of TiO2-catalytic UV-LED photo-oxidation of cyanide contained in mine wastewater and leachate.

Science.gov (United States)

Kim, Seong Hee; Lee, Sang Woo; Lee, Gye Min; Lee, Byung-Tae; Yun, Seong-Taek; Kim, Soon-Oh

2016-01-01

A photo-oxidation process using UV-LEDs and TiO2 was studied for removal of cyanide contained in mine wastewater and leachates. This study focused on monitoring of a TiO2-catalyzed LED photo-oxidation process, particularly emphasizing the effects of TiO2 form and light source on the efficiency of cyanide removal. The generation of hydroxyl radicals was also examined during the process to evaluate the mechanism of the photo-catalytic process. The apparent removal efficiency of UV-LEDs was lower than that achieved using a UV-lamp, but cyanide removal in response to irradiation as well as consumption of electrical energy was observed to be higher for UV-LEDs than for UV-lamps. The Degussa P25 TiO2 showed the highest performance of the TiO2 photo-catalysts tested. The experimental results indicate that hydroxyl radicals oxidize cyanide to OCN(-), NO2(-), NO3(-), HCO3(-), and CO3(2-), which have lower toxicity than cyanide. In addition, the overall efficacy of the process appeared to be significantly affected by diverse operational parameters, such as the mixing ratio of anatase and rutile, the type of gas injected, and the number of UV-LEDs used. Copyright © 2015 Elsevier Ltd. All rights reserved.

Combustion synthesis of red emitting borate host PDP phosphor YCaBO4: Eu3+

International Nuclear Information System (INIS)

Ingle, J.T.; Hargunani, S.P.; Sonekar, R.P.; Nagpure, P.A.; Omanwar, S.K.; Moharil, S.V.

2012-01-01

The red emitting borate host phosphor YCaBO 4 : Eu 3+ has been prepared by a novel solution combustion technique. The synthesis is based on the exothermic reaction between the fuel (Urea) and Oxidizer (Ammonium nitrate). The photoluminescence properties of the powder samples of YCaBO 4 : Eu 3+ has been investigated under UV and VUV excitation. The phosphor shows strong absorption in UV and VUV region and exhibits intense red emission upon excited by 254 nm UV and 173 nm VUV radiation. Under UV 254 nm excitation, YCaBO 4 : Eu 3+ exhibits intense red emission around 610 nm. Under VUV excitation of 173 nm, the phosphor emits intense red emission around 610 nm and few weak emissions. These weak emissions could be suppressed by annealing the sample repeatedly at proper temperature and the borate phosphor YCaBO 4 : Eu 3+ could be a good red emitting phosphor for PDP display and mercury free lamps. (author)

Color Shift Failure Prediction for Phosphor-Converted White LEDs by Modeling Features of Spectral Power Distribution with a Nonlinear Filter Approach.

Science.gov (United States)

Fan, Jiajie; Mohamed, Moumouni Guero; Qian, Cheng; Fan, Xuejun; Zhang, Guoqi; Pecht, Michael

2017-07-18

With the expanding application of light-emitting diodes (LEDs), the color quality of white LEDs has attracted much attention in several color-sensitive application fields, such as museum lighting, healthcare lighting and displays. Reliability concerns for white LEDs are changing from the luminous efficiency to color quality. However, most of the current available research on the reliability of LEDs is still focused on luminous flux depreciation rather than color shift failure. The spectral power distribution (SPD), defined as the radiant power distribution emitted by a light source at a range of visible wavelength, contains the most fundamental luminescence mechanisms of a light source. SPD is used as the quantitative inference of an LED's optical characteristics, including color coordinates that are widely used to represent the color shift process. Thus, to model the color shift failure of white LEDs during aging, this paper first extracts the features of an SPD, representing the characteristics of blue LED chips and phosphors, by multi-peak curve-fitting and modeling them with statistical functions. Then, because the shift processes of extracted features in aged LEDs are always nonlinear, a nonlinear state-space model is then developed to predict the color shift failure time within a self-adaptive particle filter framework. The results show that: (1) the failure mechanisms of LEDs can be identified by analyzing the extracted features of SPD with statistical curve-fitting and (2) the developed method can dynamically and accurately predict the color coordinates, correlated color temperatures (CCTs), and color rendering indexes (CRIs) of phosphor-converted (pc)-white LEDs, and also can estimate the residual color life.

Electron-beam-pumped phosphors

International Nuclear Information System (INIS)

Goldhar, J.; Krupke, W.F.

1985-01-01

Electron-beam excitation of solid-state scintillators, or phosphors, can result in efficient generation of visible light confined to relatively narrow regions of the spectrum. The conversion efficiency can exceed 20%, and, with proper choice of phosphors, radiation can be obtained anywhere from the near infrared (IR) to the near ultraviolet (UV). These properties qualify the phosphors as a potentially useful pump source for new solid-state lasers. New phosphors are being developed for high-brightness television tubes that are capable of higher power dissipation. Here, an epitaxial film of fluorescing material is grown on a crystalline substrate with good thermal properties. For example, researchers at North American Philips Laboratories have developed a cerium-doped yttrium aluminum garnet (YAG) grown on a YAG substrate, which has operated at 1 A/cm 2 at 20 kV without observed thermal quenching. The input power is higher by almost two orders of magnitude than that which can be tolerated by a conventional television phosphor. The authors describe tests of these new phosphors

Generation of solar spectrum by using LEDs

Science.gov (United States)

Lu, Pengzhi; Yang, Hua; Pei, Yanrong; Li, Jing; Xue, Bin; Wang, Junxi; Li, Jinmin

2016-09-01

Light emitting diode (LED) has been recognized as an applicable light source for indoor and outdoor lighting, city beautifying, landscape facilities, and municipal engineering etc. Conventional LED has superior characteristics such as long life time, low power consumption, high contrast, and wide viewing angle. Recently, LED with high color-rendering index and special spectral characteristics has received more and more attention. This paper is intended to report a solar spectrum simulated by multichip LED light source. The typical solar spectrum of 5500k released by CIE was simulated as a reference. Four types of LEDs with different spectral power distributions would be used in the LED light source, which included a 430nm LED, a 480nm LED, a 500nm LED and a white LED. In order to obtain better simulation results, the white LED was achieved by a 450nm LED chip with the mixture of phosphor. The phosphor combination was prepared by mixing green phosphor, yellow phosphor and red phosphor in a certain proportion. The multichip LED light source could provide a high fidelity spectral match with the typical solar spectrum of 5500k by adjusting injection current to each device. The luminous flux, CIE chromaticity coordinate x, y, CCT, and Ra were 104.7 lm, 0.3337, 0.3681, 5460K, and 88.6, respectively. Because of high color-rendering index and highly match to the solar spectrum, the multichip LED light source is a competitive candidate for applications where special spectral is required, such as colorimetric measurements, visual inspection, gemstone identification and agriculture.

The influence of surface topography of UV coated and printed cardboard on the print gloss

Directory of Open Access Journals (Sweden)

Igor Karlović

2010-09-01

Full Text Available The incident light on the printed surface undergoes through several processes of scattering, absorbtion and reflectiondepending on the surface topography and structure of the material. The specular part of the surface reflection is commonlyattributed as the geometric component of the reflection, and when measured is associated with specular gloss.The diffuse part of the surface reflection contains the chromatic part of the reflection and is commonly calculatedthrough colorimetric values. Using UV coatings as surface enhacement materials which affect the optical propertiesof coated surfaces and final appearance of the printed product forms new surface topography over the existingone. We have investigated the influence of three different amounts of UV glossy and matte oveprint coating on themeasured specular gloss of printed cardboard samples. The different amount of coatings on the printed samples wereachived using three different screen stencils of 180 threads/cm, 150 threads/cm and 120 threads/cm thread count.The cardboard samples were analysed with AFM and SEM microscopes to obtain surface topography and roughnessvalues which were evaluated with the measured geometric values speficied as instrumental gloss. The surfaceswith a specific amount of UV coatings showed a new formed topography which influences the reflection of light.The changes in topography were evaluated through surface roughness parameters which showed a decline of surfaceroughness with tht additional ammount of glossy and matte coatings. The obtained and calculated correlations showthere is a high correlation between coating ammount and surface roughness change and gloss for the glossy UVcoating. The results for the matte UV coatings showed lower correlation for the gloss and surface roughness.

[The spectrogram characteristics of organic blue-emissive light-emitting excitated YAG : Ce phosphor].

Science.gov (United States)

Xi, Jian-Fei; Zhang, Fang-Hui; Mu, Qiang; Zhang, Mai-Li

2011-09-01

It is demonstrated that the panchromatic luminescence devices with organic blue-emissive light-emitting was fabricated. This technique used down conversion, which was already popular in inorganic power LEDs to obtain white light emission. A blue OLED device with a configuration of ITO/2T-NATA (30 nm)/AND : TBPe (50 Wt%, 40 nm)/Alq3 (100 nm)/LiF(1 nm)/Al(100 nm) was prepared via vacuum deposition process, and then coated with YAG : Ce phosphor layers of different thicknesses to obtain a controllable and uniform shape while the CIE coordinates were fine tuned. This development not only decreased steps of technics and degree of difficulty, but also applied the mature technology of phosphor. The results showed that steady spectrogram was obtained in the devices with phosphor, with a best performance of a maximum luminance of 13 840 cd x m(-2) which was about 2 times of that of the devices without phosphor; a maximum current efficiency of 17.3 cd x A(-1) was increased more two times more than the devices without phosphor. The emission spectrum could be adjusted by varying the concentration and thickness of the phosphor layers. Absoulte spectrogram of devices was in direct proportion with different driving current corresponding.

Novel tunable green-red-emitting oxynitride phosphors co-activated with Ce3+, Tb3+, and Eu3+: photoluminescence and energy transfer.

Science.gov (United States)

Huo, Jiansheng; Dong, Langping; Lü, Wei; Shao, Baiqi; You, Hongpeng

2017-07-14

A series of novel Ce 3+ , Tb 3+ and Eu 3+ ion doped Y 4 SiAlO 8 N-based oxynitride phosphors were synthesized by the solid-state method and characterized by X-ray powder diffraction, scanning electron microscopy, photoluminescence, lifetimes and thermo-luminescence. The excitation of the Ce 3+ /Tb 3+ co-doped and Ce 3+ /Tb 3+ /Eu 3+ tri-doped phosphor with near-UV radiation results in strong linear Tb 3+ green and Eu 3+ red emission. The occurrence of Ce 3+ -Tb 3+ and Ce 3+ -Tb 3+ -Eu 3+ energy transfer processes is responsible for the bright green or red luminescence. The Tb 3+ ion acting as an energy transfer bridge can alleviate MMCT quenching between the Ce 3+ -Eu 3+ ion pairs. The lifetime measurements demonstrated that the energy-transfer mechanisms of Ce 3+ → Tb 3+ and Tb 3+ → Eu 3+ are dipole-quadrupole and quadrupole-quadrupole interactions, respectively. The temperature dependent luminescence measurements showed that as-prepared green/red phosphors have good thermal stability against temperature quenching. The obtained results indicate that these phosphors might serve as promising candidates for n-UV LEDs.

Color Shift Failure Prediction for Phosphor-Converted White LEDs by Modeling Features of Spectral Power Distribution with a Nonlinear Filter Approach

Directory of Open Access Journals (Sweden)

Jiajie Fan

2017-07-01

Full Text Available With the expanding application of light-emitting diodes (LEDs, the color quality of white LEDs has attracted much attention in several color-sensitive application fields, such as museum lighting, healthcare lighting and displays. Reliability concerns for white LEDs are changing from the luminous efficiency to color quality. However, most of the current available research on the reliability of LEDs is still focused on luminous flux depreciation rather than color shift failure. The spectral power distribution (SPD, defined as the radiant power distribution emitted by a light source at a range of visible wavelength, contains the most fundamental luminescence mechanisms of a light source. SPD is used as the quantitative inference of an LED’s optical characteristics, including color coordinates that are widely used to represent the color shift process. Thus, to model the color shift failure of white LEDs during aging, this paper first extracts the features of an SPD, representing the characteristics of blue LED chips and phosphors, by multi-peak curve-fitting and modeling them with statistical functions. Then, because the shift processes of extracted features in aged LEDs are always nonlinear, a nonlinear state-space model is then developed to predict the color shift failure time within a self-adaptive particle filter framework. The results show that: (1 the failure mechanisms of LEDs can be identified by analyzing the extracted features of SPD with statistical curve-fitting and (2 the developed method can dynamically and accurately predict the color coordinates, correlated color temperatures (CCTs, and color rendering indexes (CRIs of phosphor-converted (pc-white LEDs, and also can estimate the residual color life.

340nm UV LED excitation in time-resolved fluorescence system for europium-based immunoassays detection

OpenAIRE

Rodenko, Olga; Fodgaard, Henrik; Tidemand-Lichtenberg, Peter; Pedersen, Christian

2017-01-01

In immunoassay analyzers for in-vitro diagnostics, Xenon flash lamps have been widely used as excitation light sources. Recent advancements in UV LED technology and its advantages over the flash lamps such as smaller footprint, better wall-plug efficiency, narrow emission spectrum, and no significant afterglow, have made them attractive light sources for gated detection systems. In this paper, we report on the implementation of a 340 nm UV LED based time-resolved fluorescence system based on ...

Phosphors containing boron and metals of Group IIIA and IIIB

Science.gov (United States)

Setlur, Anant Achyut; Srivastava, Alok Mani; Comanzo, Holly Ann; Manivannan, Venkatesan

2006-10-31

A phosphor comprises: (a) at least a first metal selected from the group consisting of yttrium and elements of lanthanide series other than europium; (b) at least a second metal selected from the group consisting of aluminum, gallium, indium, and scandium; (c) boron; and (d) europium. The phosphor is used in light source that comprises a UV radiation source to convert UV radiation to visible light.

Correlation of Structure, Tunable Colors, and Lifetimes of (Sr, Ca, Ba)Al2O4:Eu2+, Dy3+ Phosphors

Science.gov (United States)

Xie, Qidi; Li, Bowen; He, Xin; Zhang, Mei; Chen, Yan; Zeng, Qingguang

2017-01-01

(Sr, Ca, Ba)Al2O4:Eu2+, Dy3+ phosphors were prepared via a high temperature solid-state reaction method. The correlation of phase structure, optical properties and lifetimes of the phosphors are investigated in this work. For the (Sr, Ca)Al2O4:Eu2+, Dy3+ phosphors, the different phase formation from monoclinic SrAl2O4 phase to hexagonal SrAl2O4 phase to monoclinic CaAl2O4 phase was observed when the Ca content increased. The emission color of SrAl2O4:Eu2+, Dy3+ phosphors varied from green to blue. For the (Sr, Ba)Al2O4:Eu2+, Dy3+ phosphors, different phase formation from the monoclinic SrAl2O4 phase to the hexagonal BaAl2O4 phase was observed, along with a shift of emission wavelength from 520 nm to 500 nm. More interestingly, the decay time of SrAl2O4:Eu2+, Dy3+ changed due to the different phase formations. Lifetime can be dramatically shortened by the substitution of Sr2+ with Ba2+ cations, resulting in improving the performance of the alternating current light emitting diode (AC-LED). Finally, intense LEDs are successfully obtained by combining these phosphors with Ga(In)N near UV chips. PMID:29057839

Correlation of Structure, Tunable Colors, and Lifetimes of (Sr, Ca, BaAl2O4:Eu2+, Dy3+ Phosphors

Directory of Open Access Journals (Sweden)

Qidi Xie

2017-10-01

Full Text Available (Sr, Ca, BaAl2O4:Eu2+, Dy3+ phosphors were prepared via a high temperature solid-state reaction method. The correlation of phase structure, optical properties and lifetimes of the phosphors are investigated in this work. For the (Sr, CaAl2O4:Eu2+,Dy3+ phosphors, the different phase formation from monoclinic SrAl2O4 phase to hexagonal SrAl2O4 phase to monoclinic CaAl2O4 phase was observed when the Ca content increased. The emission color of SrAl2O4:Eu2+, Dy3+ phosphors varied from green to blue. For the (Sr, BaAl2O4:Eu2+, Dy3+ phosphors, different phase formation from the monoclinic SrAl2O4 phase to the hexagonal BaAl2O4 phase was observed, along with a shift of emission wavelength from 520 nm to 500 nm. More interestingly, the decay time of SrAl2O4:Eu2+, Dy3+changed due to the different phase formations. Lifetime can be dramatically shortened by the substitution of Sr2+ with Ba2+ cations, resulting in improving the performance of the alternating current light emitting diode (AC-LED. Finally, intense LEDs are successfully obtained by combining these phosphors with Ga(InN near UV chips.

Blue and green emissions with high color purity from nanocrystalline Ca2Gd8Si6O26:Ln (Ln = Tm or Er) phosphors

International Nuclear Information System (INIS)

Seeta Rama Raju, G.; Park, Jin Young; Jung, Hong Chae; Pavitra, E.; Moon, Byung Kee; Jeong, Jung Hyun; Yu, Jae Su; Kim, Jung Hwan; Choi, Haeyoung

2011-01-01

Graphical abstract: Highlights: → Nanocrystalline Ca 2 Gd 8 Si 6 O 26 (CGS):Tm 3+ and CGS:Er 3+ phosphors were prepared by solvothermal reaction method. → The visible luminescence properties of phosphors were investigated by exciting with ultraviolet (UV) or near-UV light and low voltage electron beam (0.5-5 kV). → The photoluminescence spectra of CGS:Tm 3+ under 359 nm excitation and CGS:Er 3+ under 380 nm excitation showed the strong blue ( 1 D 2 → 3 F 4 at 456 nm) and green ( 4 S 3/2 → 4 I 15/2 at 550 nm) colors with the color purity 87% and 96%, respectively → The low accelerating voltage cathodoluminescence spectra of CGS:Tm 3+ and CGS:Er 3+ showed the strong blue and green emissions with the high color purity 95% and 96%, respectively. → The obtained results are hint at the promising applications to produce high quality LEDs and FED devices. - Abstract: Blue and green light emissive nanocrystalline Ca 2 Gd 8 Si 6 O 26 (CGS):Tm 3+ and CGS:Er 3+ phosphors with high color purity were prepared by solvothermal reaction method. The structural and morphological properties of these phosphors were evaluated by the powder X-ray diffraction (XRD) and scanning electron microscopy, respectively. From the XRD results, Tm 3+ :CGS and Er 3+ :CGS phosphors had the characteristic peaks of oxyapatite in the hexagonal lattice structure. The visible luminescence properties of phosphors were obtained by ultraviolet (UV) or near-UV light and low voltage electron beam (0.5-5 kV) excitation. The photoluminescence and cathodoluminescence properties were investigated by changing the variation of Tm 3+ or Er 3+ concentrations and the acceleration voltage, respectively. The CGS:Tm 3+ phosphors exhibited the blue emission due to 1 D 2 → 3 F 4 transition, while the CGS:Er 3+ phosphors showed the green emission due to 4 S 3/2 → 4 I 15/2 transition. The color purity and chromaticity coordinates of the fabricated phosphors are comparable to or better than those of standard

Studies on the luminescence properties of CaZrO3:Eu3+ phosphors prepared by the solid state reaction method

Directory of Open Access Journals (Sweden)

Ishwar Prasad Sahu

2017-03-01

Full Text Available CaZrO3:xEu3+ (x = 1.0, 2.0, 3.0, 4.0, and 5.0 mol% phosphors were successfully prepared by a solid state reaction method. The crystal structure of sintered phosphors was hexagonal phase with space group of Pm-3m. The near ultra-violet (NUV excitation, emission spectra of the CaZrO3:xEu3+ phosphors were composed of sharp line emission associated with the transitions from the excited states 5D0 to the ground state 7Fj (j = 0, 1, 2, 3, 4 of Eu3+. The results indicated that CaZrO3:xEu3+ might become an important orange-red phosphor candidate for use in white light emitting diodes (WLEDs with near-UV LED chips. The mechanoluminescence (ML intensity increases linearly with increasing impact velocity of the moving piston, suggesting that the sintered phosphors can also be useful as a stress sensor.

Luminescence enhancement in Eu3+, Sm3+ co-doped liy(MoO4)2 nano-phosphors by sol-gel process.

Science.gov (United States)

Zhou, Xianju; Wang, Guangchuan; Zhou, Tonghui; Zhou, Kaining; Li, Qingxu; Wang, Zhongqing

2014-05-01

A series of LiY(0.95-x)Eu(0.05)Sm(x)(MoO4)2 red light emitting phosphors were synthesized by sol-gel technique. The phase impurity and spectroscopic properties were characterized by X-ray Diffraction (XRD), Photo-Luminescence (PL) and Photo-Luminescence Excitation (PLE) spectra, respectively. It is found that the PLE spectra of the Eu3+, Sm3+ co-doped nanoparticles are enhanced and broadened as compared with the solely doped samples, which will make the co-doped phosphors match better with blue and/or UV GaN based LED chips. The red emission intensity of Eu3+ is largely enhanced by the energy transfer from Sm3+. The mechanism of the enhancement is clearly proven to be the increase in the quantum efficiency of 5D0 state of Eu3+ rather than the increase in the absorption of Eu3+. Meanwhile, the characteristic f-f transitions of Sm3+ are greatly reduced, resulting in little influence in the color purity of the co-doped phosphors. The present material is an amendatory promising red light emitting phosphor for white LEDs.

Enhanced red emission of LaVO{sub 4}:Eu{sup 3+} phosphors by Li-doping

Energy Technology Data Exchange (ETDEWEB)

Park, Sung Wook; Yang, Hyun Kyoung; Chung, Jong Won; Moon, Byung Kee; Choi, Byung Chun; Jeong, Jung Hyun [Pukyoung National University, Busan (Korea, Republic of); Jang, Ki Wan; Lee, Ho Sueb [Changwon National University, Changwon (Korea, Republic of); Yi, Soung Soo [Silla University, Busan (Korea, Republic of)

2010-12-15

LaVO{sub 4} phosphors were synthesized by using a solid state reaction, and were characterized by using X-ray diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence (PL). The XRD patterns of the Li-doped LaVO{sub 4}:Eu{sup 3+} powder phosphors revealed a mixture of tetragonal and monoclinic phases. The tetragonal phase of the LaVO{sub 4}:Eu{sup 3+} phosphor showed a higher PL intensity than the monoclinic one, despite the presence of both monoclinic and tetragonal structures. The Li-doped LaVO{sub 4}:Eu{sup 3+} powder phosphors absorbed strongly at 396 nm and exhibited strong red emission at approximately 619.5 nm due to the {sup 5}D{sub 0} {yields} {sup 7}F{sub 2} transition. The incorporation of Li{sup +} ions into the LaVO{sub 4}:Eu{sup 3+} powder can lead to a remarkable increase in photoluminescence. The enhanced luminescence is attributed to the incorporation of Li{sup +} ions that may act as a sensitizers for effective energy transfer. This phosphor has promising applications in near-UV light-emitting diodes(LEDs).

UV-activated 7-dehydrocholesterol-coated titanium implants promote differentiation of human umbilical cord mesenchymal stem cells into osteoblasts.

Science.gov (United States)

Satué, María; Ramis, Joana M; Monjo, Marta

2016-01-01

Vitamin D metabolites are essential for bone regeneration and mineral homeostasis. The vitamin D precursor 7-dehydrocholesterol can be used after UV irradiation to locally produce active vitamin D by osteoblastic cells. Furthermore, UV-irradiated 7-dehydrocholesterol is a biocompatible coating for titanium implants with positive effects on osteoblast differentiation. In this study, we examined the impact of titanium implants surfaces coated with UV-irradiated 7-dehydrocholesterol on the osteogenic differentiation of human umbilical cord mesenchymal stem cells. First, the synthesis of cholecalciferol (D3) was achieved through the incubation of the UV-activated 7-dehydrocholesterol coating for 48 h at 23℃. Further, we investigated in vitro the biocompatibility of this coating in human umbilical cord mesenchymal stem cells and its potential to enhance their differentiation towards the osteogenic lineage. Human umbilical cord mesenchymal stem cells cultured onto UV-irradiated 7-dehydrocholesterol-coated titanium implants surfaces, combined with osteogenic supplements, upregulated the gene expression of several osteogenic markers and showed higher alkaline phosphatase activity and calcein blue staining, suggesting increased mineralization. Thus, our results show that the use of UV irradiation on 7-dehydrocholesterol -treated titanium implants surfaces generates a bioactive coating that promotes the osteogenic differentiation of human umbilical cord mesenchymal stem cells, with regenerative potential for improving osseointegration in titanium-based bone anchored implants. © The Author(s) 2015.

Packaging technology of LEDs for LCD backlights

International Nuclear Information System (INIS)

Fan Manning; Liang Meng; Wang Guohong

2009-01-01

We design a package patterned with red and green emitting phosphors excited by a blue LED to emit tri-basic mixing color. For high backlight display quality, we compare several phosphors. According to our measurements, green phosphors 0752G, 0753G and red phosphor 0763R are preferred for producing a good backlight source. Compared to RGB-LED backlight units, this frame typically benefits the lighting uniformity, and can simplify the structures. It also provides higher color render and better CCT than the traditional package method of a yellow phosphor with a blue chip. However, its light efficiency needs to be further improved for the use of backlights for LCDs.

Novel Transparent Phosphor Conversion Matrix with High Thermal Conductivity for Next Generation Phosphor-Converted LED-based Solid State Lighting

Energy Technology Data Exchange (ETDEWEB)

Bockstaller, Michael [Carnegie Mellon Univ., Pittsburgh, PA (United States)

2017-02-06

The low thermal conductivity of state-of-the-art polymer encapsulants (k ~ 0.15 Wm-1K-1) limits the efficiency and power density of current phosphor conversion light emitting diodes (pc-LEDs). The technical objective of this project was to demonstrate synthesis and processing schemes for the fabrication of polymer hybrid encapsulants with a thermal conductivity exceeding k = 0.4 Wm-1K-1 for LED applications. The ‘hybrid polymer’ approach encompasses the dispersion of high thermal conductivity particle fillers (zinc oxide, ZnO as well as the alpha-polymorph of alumina, Al2O3) within a polysiloxane matrix (poly(dimethylsiloxane), PDMS as well as poly(phenyl methyl siloxane), PPMS) to increase the thermal conductivity while maintaining optical transparency and photothermal stability at levels consistent with LED applications. To accomplish this goal, a novel synthesis method for the fabrication of nanosized ZnO particles was developed and a novel surface chemistry was established to modify the surface of zinc oxide particle fillers and thus to enable their dispersion in poly(dimethyl siloxane) (PDMS) matrix polymers. Molecular dynamics and Mie simulations were used to optimize ligand structure and to enable the concurrent mixing of particles in PDMS/PPMS embedding media while also minimizing the thermal boundary resistance as well as optical scattering of particle fillers. Using this approach the synthesis of PDMS/ZnO hybrid encapsulants exhibiting a thermal conductivity of 0.64 Wm-1K-1 and optical transparency > 0.7 mm-1 was demonstrated. A forming process based on micromolding was developed to demonstrate the forming of particle filled PDMS into film and lens shapes. Photothermal stability testing revealed stability of the materials for approximately 4000 min when exposed to blue light LED (450 nm, 30 W/cm2). One postgraduate and seven graduate students were supported by the project. The research performed within this project led to fifteen publications in peer

Transition of Emission Colours as a Consequence of Heat-Treatment of Carbon Coated Ce3+-Doped YAG Phosphors

NARCIS (Netherlands)

Yin, L.J.; Dierre, B.F.P.R.; Sekiguchi, Takashi; van Ommen, J.R.; Hintzen, H.T.J.M.; Cho, Yujin

2017-01-01

To modify the luminescence properties of Ce³⁺-doped Y₃Al₅O₁₂ (YAG) phosphors, they have been coated with a carbon layer by chemical vapor deposition and subsequently heat-treated at high temperature under N₂ atmosphere. Luminescence of the

New facilities for Al+MgF2 coating for 2-m class mirrors for UV

Science.gov (United States)

Zhupanov, Valery; Vlasenko, Oleg; Sachkov, Mikhail; Fedoseev, Viktor

2014-07-01

The World Space Observatory--Ultraviolet (WSO--UV) project is a Russian-Spanish space mission for spectroscopic and imaging observations in the UV domain (115-320 nm) where some of the most important astrophysical processes can be efficiently studied with unprecedented capability. In the horizon of the next decade, WSO--UV will be the only mission with the large primary mirror fully devoted for UV studies. The observatory includes a 170 cm aperture telescope capable of high-resolution spectroscopy, long slit low-resolution spectroscopy, and deep UV imaging. The telescope T-170M is a Ritchey-Chrétien with a F/10 focal ratio and a corrected field of view of 0.5 degrees. Specific data on the WSO-UV project (telescope, satellite, orbit, launcher, ground segment, etc.) are given in [1-6]. The current status of the WSO-UV focal plane instruments, their status of implementation, and the expected performances are presented in [7]. The science drivers of the WSO-UV mission are described in [8, 9]. The main WSO-UV instruments, spectrographs (WUVS instrument) and imagers (ISSIS instrument) are described in [10-13] and [14-15] correspondingly. The prospects of stellar studies with WSO-UV are presented in papers [16-17]. A paper [18] describes our experience of using the DP-190 glue for adhesive attachment of a large space mirror and its rim. In the instrument compartment, see Figure 1, the optical bench (OB) - used as reference plane for all the onboard instrumentation - is aligned and maintained in the correct position with respect to the primary mirror (PM) using a three rods system. An imaging instrument ISSIS is mounted on the upper basis of the optical bench, in the space available between the PM and the OB itself, while spectrographs (WUVS instrument) are mounted to the OB bottom basis. One of the primary tasks in creating telescope's PM is to apply coating with required reflective and protective properties. Aluminum is a well known reflecting coating for wavelength

An imaging system for quantitive surface temperature mapping using two-color thermographic phosphors

Science.gov (United States)

Buck, Gregory M.

1988-01-01

A technique for obtaining detailed quantitative temperature distributions on test models in hypersonic wind tunnels is presented. This technique is based on the ratio of blue to green (450, 520 nm) emission from an UV (365 nm) excited phosphor coating. Separately filtered images are recorded from a three-tube color camera, utilizing off-the-shelf front-end video optics to discriminate wavelengths. Two demonstration studies in a 31-inch Mach 10 tunnel are discussed. One study presents the windward surface temperature-time history for a transatmospheric vehicle, and the other illustrates nosetip heating on a spherically blunted slender cone.

Demonstration of 575-Mb/s downlink and 225-Mb/s uplink bi-directional SCM-WDM visible light communication using RGB LED and phosphor-based LED.

Science.gov (United States)

Wang, Yuanquan; Wang, Yiguang; Chi, Nan; Yu, Jianjun; Shang, Huiliang

2013-01-14

We propose and experimentally demonstrate a novel full-duplex bi-directional subcarrier multiplexing (SCM)-wavelength division multiplexing (WDM) visible light communication (VLC) system based on commercially available red-green-blue (RGB) light emitting diode (LED) and phosphor-based LED (P-LED) with 575-Mb/s downstream and 225-Mb/s upstream transmission, employing various modulation orders of quadrature amplitude modulation (QAM) orthogonal frequency division multiplexing (OFDM). For the downlink, red and green colors/wavelengths are assigned to carry useful information, while blue chip is just kept lighting to maintain the white color illumination, and for the uplink, the low-cost P-LED is implemented. In this demonstration, pre-equalization and post-equalization are also adopted to compensate the severe frequency response of LEDs. Using this scheme, 4-user downlink and 1-user uplink transmission can be achieved. Furthermore, it can support more users by adjusting the bandwidth of each sub-channel. Bit error rates (BERs) of all links are below pre-forward-error-correction (pre-FEC) threshold of 3.8x 10(-3) after 66-cm free-space delivery. The results show that this scheme has great potential in the practical VLC system.

Novel Coatings for Enhancement of Light-Emitting Diodes (LEDs)

Science.gov (United States)

2006-10-28

quantum efficiency of LEDs. SAIC’s strength is this area is a proprietary nonimaging optics code. In consultation with Lumileds, SAIC developed designs for...five different optical ele- ments that collect and project light from a LED. The simulations showed that the designs achieve a significant improvement... optical microscope at 100x power the coating is not visible. Fire sample 6DecO4P1 in tube furnace As a first test, sample 6Dec04P1 was progressively

Preparation and luminescence properties of Ca3(VO4)2: Eu3+, Sm3+ phosphor for light-emitting diodes

International Nuclear Information System (INIS)

Huang Jiaping; Li Qiuxia; Chen Donghua

2010-01-01

Rare-earth ions co-activated red phosphors Ca 3 (VO 4 ) 2 : Eu 3+ , Sm 3+ were synthesized by modified solid-state reactions. The samples were characterized by X-ray powder diffractometer (XRD), energy-dispersive X-ray spectrometer (EDS), transmission electron microscopy (TEM) and luminescence spectrometer (LS). The results showed that the Eu-Sm system exhibits higher emission intensity than those of the Eu single-doped system and Sm separate-doped system under blue light. Samarium (III) ions are effective in broadening and strengthening absorptions around 467 nm. Furthermore, they exhibit enhanced luminescence emission. Luminescent measurements showed that the phosphors can be efficiently excited by ultraviolet (UV) to visible region, emitting a red light with a peak wavelength of 616 nm. The material has potential application as a phosphor for light-emitting diodes (LEDs).

White LEDs with limit luminous efficacy

Energy Technology Data Exchange (ETDEWEB)

Lisitsyn, V. M.; Stepanov, S. A., E-mail: stepanovsa@tpu.ru; Yangyang, Ju [National Research Tomsk Polytechnic University, 30 Lenin Av., Tomsk, 634050 (Russian Federation); Lukash, V. S. [JSC Research Institute of Semiconductor Devices, 99a Krasnoarmeyskaja St., Tomsk, 634050 (Russian Federation)

2016-01-15

In most promising widespread gallium nitride based LEDs emission is generated in the blue spectral region with a maximum at about 450 nm which is converted to visible light with the desired spectrum by means of phosphor. The thermal energy in the conversion is determined by the difference in the energies of excitation and emission quanta and the phosphor quantum yield. Heat losses manifest themselves as decrease in the luminous efficacy. LED heating significantly reduces its efficiency and life. In addition, while heating, the emission generation output and the efficiency of the emission conversion decrease. Therefore, the reduction of the energy losses caused by heating is crucial for LED development. In this paper, heat losses in phosphor-converted LEDs (hereinafter chips) during spectrum conversion are estimated. The limit values of the luminous efficacy for white LEDs are evaluated.

White LED based on CaAl2Si2O8:Eu2+ Mn2+ phosphor and CdS/ZnS quantum dots

Science.gov (United States)

Shen, Changyu; Zhong, Chuan; Hou, Qianglong; Li, Ke

2011-02-01

Core/shell CdS/ZnS quantum dots (QDs) with the emission wavelength of 610nm, was synthesized by thermal deposition using cadmium oxide and selenium as precursors in a hot lauric acid and hexadecylamine trioctylphosphine oxide hybrid. CaAl2Si2O8:Eu2+ Mn2+ phosphor was synthesized by high-temperature solid state reaction at 1290 °C for 2 hours under the H2 reducing atmosphere, and X-ray powder diffraction analysis confirmed the formation of it. It has two emission bands peaking at 420 nm and 580nm originated from the transition 5d to 4f of Eu2+ and 4T1-6A1 of Mn2+, respectively. Blends of CaAl2Si2O8:Eu2+,Mn2+ phosphor and CdS/ZnS QDs exhibited the prominent spectral evolution with an increasing content of QDs. A hybrid white LED, which combines a blue LED with the blend of CaAl2Si2O8:Eu2+ Mn2+ phosphor and QDs with a weight ratio of 2:1, with the CIE coordinate of (0.3183, 0.3036) and CRI of 85 was obtained.

Developing LED UV fluorescence sensors for online monitoring DOM and predicting DBPs formation potential during water treatment.

Science.gov (United States)

Li, Wen-Tao; Jin, Jing; Li, Qiang; Wu, Chen-Fei; Lu, Hai; Zhou, Qing; Li, Ai-Min

2016-04-15

Online monitoring dissolved organic matter (DOM) is urgent for water treatment management. In this study, high performance size exclusion chromatography with multi-UV absorbance and multi-emission fluorescence scans were applied to spectrally characterize samples from 16 drinking water sources across Yangzi River and Huai River Watersheds. The UV absorbance indices at 254 nm and 280 nm referred to the same DOM components and concentration, and the 280 nm UV light could excite both protein-like and humic-like fluorescence. Hence a novel UV fluorescence sensor was developed out using only one UV280 light-emitting diode (LED) as light source. For all samples, enhanced coagulation was mainly effective for large molecular weight biopolymers; while anion exchange further substantially removed humic substances. During chlorination tests, UVA280 and UVA254 showed similar correlations with yields of disinfection byproducts (DBPs); the humic-like fluorescence obtained from LED sensors correlated well with both trihalomethanes and haloacetic acids yields, while the correlation between protein-like fluorescence and trihalomethanes was relatively poor. Anion exchange exhibited more reduction of DBPs yields as well as UV absorbance and fluorescence signals than enhanced coagulation. The results suggest that the LED UV fluorescence sensors are very promising for online monitoring DOM and predicting DBPs formation potential during water treatment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Characterization and optimization of an inkjet-printed smart textile UV-sensor cured with UV-LED light

Science.gov (United States)

Seipel, S.; Yu, J.; Periyasamy, A. P.; Viková, M.; Vik, M.; Nierstrasz, V. A.

2017-10-01

For the development of niche products like smart textiles and other functional high-end products, resource-saving production processes are needed. Niche products only require small batches, which makes their production with traditional textile production techniques time-consuming and costly. To achieve a profitable production, as well as to further foster innovation, flexible and integrated production techniques are a requirement. Both digital inkjet printing and UV-light curing contribute to a flexible, resource-efficient, energy-saving and therewith economic production of smart textiles. In this article, a smart textile UV-sensor is printed using a piezoelectric drop-on-demand printhead and cured with a UV-LED lamp. The UVcurable ink system is based on free radical polymerization and the integrated UVsensing material is a photochromic dye, Reversacol Ruby Red. The combination of two photoactive compounds, for which UV-light is both the curer and the activator, challenges two processes: polymer crosslinking of the resin and color performance of the photochromic dye. Differential scanning calorimetry (DSC) is used to characterize the curing efficiency of the prints. Color measurements are made to determine the influence of degree of polymer crosslinking on the developed color intensities, as well as coloration and decoloration rates of the photochromic prints. Optimized functionality of the textile UV-sensor is found using different belt speeds and lamp intensities during the curing process.

The Use of Ultra-Violet (UV) Light Emitting Diodes (LEDS) in an Advanced Oxidation Process (AOP) with Brilliant Blue FCF as an Indicator

Science.gov (United States)

2015-03-26

LEDs have the potential to replace mercury lamps in many UV processes, as well as open the door to new applications of UV light based on their unique...al. 2007, Autin, Romelot, et al. 2013). UV LEDs in AOPs While most data on AOP experimentation are based on experiments that use mercury lamps ...metaldehyde in solution. Their experiments found that similar UV light exposure levels from UV LEDs and traditional mercury lamps produced similar

Novel UV cured polymers for coating and recycling cellulosics, application to a unique paper / veneer from the waste banana tree

International Nuclear Information System (INIS)

Dennis, G.R.; Garnett, J.L.; Jarrett, K.J.

2007-01-01

Work involving UV curing and cure-grafting processes on material from the waste banana tree has been performed. Water compatible oligomers of unique structure and processing novel properties have been used in this treatment. The material from the waste banana tree has been obtained by a peeling process and can be treated either as a type of paper or as a modified timber veneer leading to two general lines of potential commercial products. The peeled product is coated with formulations containing the novel oligomers and UV cured. The advantages of using these unique water compatible oligomers in all general UV curing systems are discussed. The effect of including nanoparticle fillers in these coating formulations is considered. The effect of the presence of lignin in the banana ply paper on the curing process is examined by comparing the banana ply paper curing data with analogous results from a pure cellulose Whatman 41 paper. Two UV lamps have been used in these studies, a Fusion F-300 and a Con-Trol-Cure LED, the latter shown to be safer from body exposure considerations because it operates in a 385-405 nm wavelength band. A mechanism for the curing and cure-grafting process on banana ply paper/veneer has been proposed. The commercial potential of this process is discussed especially the economic advantages of using the banana ply paper/veneer which is not chemically pulped. (Author)

Preparation and antibacterial activities of chitosan-gallic acid/polyvinyl alcohol blend film by LED-UV irradiation.

Science.gov (United States)

Yoon, Soon-Do; Kim, Young-Mog; Kim, Boo Il; Je, Jae-Young

2017-11-01

Active blend films from chitosan-gallic acid (CGA) and polyvinyl alcohol (PVA) were prepared via a simple mixing and casting method through the addition of citric acid as a plasticizer. The CGA/PVA blend films were characterized using Fourier transform infrared spectroscopy (FT-IR). The mechanical properties including tensile strength (TS) and elongation at break (%E), degree of solubility (S) and swelling behavior (DS), water vapor adsorption, and antimicrobial activities of the CGA/PVA blend films with and without LED (light emitting diode)-UV irradiation were also investigated. The CGA/PVA blend films exposed to UV irradiation exerted a higher TS (43.5MPa) and lower %E (50.40), S (0.38) and DS (2.73) compared to the CGA/PVA blend films (TS=41.7MPa, %E=55.40, S=0.42, and DS=3.16) not exposed LED-UV irradiation, indicating that the cross-linkage between CGA and PVA had been strengthened by LED-UV irradiation. However, the water vapor adsorption in the CGA/PVA blend films increased due to the changes of surface roughness and pore volume after LED-UV irradiation, and all values increased by increasing the CGA concentrations in the CGA/PVA blend films. The antimicrobial activities of the CGA/PVA blend films showed that the efficient concentration of CGA in the CGA/PVA blend films was over 1.0%. Taken together, the CGA/PVA blend films have potential for use as food packing materials. Copyright © 2017 Elsevier B.V. All rights reserved.

Luminescent properties of MAl(SO4)2 Br:Eu(3+) (M = Sr or Mg) red phosphors for near-UV light-emitting diodes.

Science.gov (United States)

Deshmukh, Priti B; Puppalwar, S P; Dhoble, N S; Dhoble, S J

2015-02-01

Eu(3+) -activated MAl(SO4 )2 Br phosphors (where M = Mg or Sr) are successfully prepared using a wet chemical reaction technique. The samples are characterized by X-ray diffraction (XRD) and photoluminescence (PL) spectroscopies. The XRD pattern revealed that both the samples are microcrystalline in nature. PL of Eu(3+) -doped SrAl(SO4 )2 Br and MgAl(SO4 )2 Br phosphors exhibited characteristic red emission coming from the (5) D0  → (7) F2 (616 nm) electron transition, when excited by 396 nm wavelength of light. The maximum intensity of luminescence was observed at a concentration of 1 mol% Eu(3+) . The intensity of the electric dipole transition at 616 nm is greater than that of the magnetic dipole transition at 594 nm. The results showed that MAl(SO4 )2 Br:Eu(3+) , (M = Mg, Sr) phosphors have potential application in near-UV light-emitting diodes as efficient red-emitting phosphor. Copyright © 2014 John Wiley & Sons, Ltd.

Synthesis and Luminescence Properties of Blue Na(Sr0.97-xCa(x))PO4:0.03Eu2+ Phosphors for White Light Emitting Diode Applications.

Science.gov (United States)

Hakeem, D A; Park, K

2015-07-01

The crystal structure and luminescence properties of Na(Sr0.97-xCax)PO4:0.03Eu2+ (0 phosphors were studied, depending on the Ca2+ concentration. All the Na(Sr0.97-xCax)PO4:0.03Eu2+ phosphors had a hexagonal crystal structure. The excitation spectra of the prepared phosphors showed a broad band ranging from 250 to 420 nm, which arises due to the 4f-5d transitions of Eu2+ ions. Upon the excitation of 334 nm wavelength, the emission spectra showed a broad blue band ranging from 400 to 700 nm peaking at 450 nm. Among the prepared phosphors, the Na(Sr0.72Ca0.25)PO4:0.03Eu2+ showed the strongest emission intensity and could be applied as a blue emitting phosphor for UV-based w-LEDs.

Red emitting phosphors of Eu{sup 3+} doped Na{sub 2}Ln{sub 2}Ti{sub 3}O{sub 10} (Ln = Gd, Y) for white light emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Zhang, Niumiao [National Key Laboratory of Photoelectric Technology and Functional Materials Culture Base in Shaanxi Province, National Photoelectric Technology and Functional Materials & Application of Science and Technology International Cooperation Base, Institute of Photonics & Photon-Technology, Northwest University, Xi’an 710069 (China); Guo, Chongfeng, E-mail: guocf@nwu.edu.cn [National Key Laboratory of Photoelectric Technology and Functional Materials Culture Base in Shaanxi Province, National Photoelectric Technology and Functional Materials & Application of Science and Technology International Cooperation Base, Institute of Photonics & Photon-Technology, Northwest University, Xi’an 710069 (China); Yin, Luqiao; Zhang, Jianhua [Key Laboratory of Advanced Display and System Applications (Shanghai University), Ministry of Education, Shanghai 200072 (China); Wu, Mingmei, E-mail: ceswmm@mail.sysu.edu.cn [School of Chemistry and Chemical Engineering, Sun Yat-Sen University, No. 135, Xingang Xi Road, Guangzhou 510275 (China)

2015-06-25

Highlights: • Layered red phosphors Na{sub 2}Ln{sub 2}Ti{sub 3}O{sub 10} (Ln = Gd, Y):Eu{sup 3+} were prepared. • The synthesis parameters of phosphors were optimized. • PL and thermal stability of the samples were investigated. • LED devices were also fabricated including the present red phosphor. - Abstract: A series of Eu{sup 3+} doped Na{sub 2}Ln{sub 2}Ti{sub 3}O{sub 10} (Ln = Gd, Y) red-emitting phosphors for application in ultraviolet based light emitting diodes (LEDs) were successfully synthesized by a modified sol–gel method. Their structure and luminescent properties were characterized by powder X-ray diffraction (XRD), photoluminescence excitation (PLE) and emission (PL) spectra and absorption spectra, according to these results the optimal compositions and synthesis parameters were determined. In addition, the thermal stabilities of the phosphors were investigated according to the temperature-dependent PL spectra. The red and white-LEDs (W-LEDs) comprising the Na{sub 2}Ln{sub 2}Ti{sub 3}O{sub 10}:Eu{sup 3+} (Ln = Gd, Y) red emitting phosphors were fabricated with a near-ultraviolet (n-UV) chip. In comparison with Na{sub 2}Y{sub 1.4}Eu{sub 0.6}Ti{sub 3}O{sub 10}, the Na{sub 2}Gd{sub 0.6}Eu{sub 1.4}Ti{sub 3}O{sub 10} phosphor offers higher brightness, quantum efficiency, and excellent thermal stability. W-LEDs comprising Na{sub 2}Gd{sub 0.6}Eu{sub 1.4}Ti{sub 3}O{sub 10} showed bright white emission with a color rendering index (Ra) of 82, a color temperature of 2151 K, and Commission Internationale de I’Eclairage (CIE) color coordinates of (0.34, 0.37). The phosphor Na{sub 2}Gd{sub 0.6}Eu{sub 1.4}Ti{sub 3}O{sub 10} is more suitable candidate for application in LEDs.

Understanding and controlling chromaticity shift in LED devices

Energy Technology Data Exchange (ETDEWEB)

Davis, Lynn; Mills, Karmann; Lamvik, Michael; Perkins, Curtis; Bobashev, Georgiy; Young, Joseph; Yaga, Robert; Johnson, Cortina

2017-05-30

Chromaticity shift in light-emitting diode (LED) devices arises from multiple mechanisms, and at least five different chromaticity shift modes (CSMs) have been identified to date. This paper focuses on the impacts of irreversible phosphor degradation as a cause of chromaticity shifts in LED devices. The nitride phosphors used to produce warm white LEDs are especially vulnerable to degradation due to thermal and chemical effects such as reactions with oxygen and water. As a result, LED devices utilizing these phosphors were found to undergo either a green shift or, less commonly, a red shift depending on the phosphor mix in the LED devices. These types of chromaticity shifts are classified as CSM-2 (green shift) and CSM-5 (red shift). This paper provides an overview of the kinetic processes responsible for green and red chromaticity shifts along with examples from accelerated stress testing of 6” downlights. Both CSMs appear to proceed through analogous mechanisms that are initiated at the surface of the phosphor. A green shift is produced by the surface oxidation of the nitride phosphor that changes the emission profile to lower wavelengths. As the surface oxidation reaction proceeds, reactant limitations slow the rate and bulk oxidation processes become more prevalent. We found that a red chromaticity shift arises from quenching of the green phosphor, also possibly due to surface reactions of oxygen, which shift the emission chromaticity in the red direction. In conclusion, we discuss the implications of these findings on projecting chromaticity.

Characterization of ZnO coated polyester fabrics for UV protection

International Nuclear Information System (INIS)

Broasca, G.; Borcia, G.; Dumitrascu, N.; Vrinceanu, N.

2013-01-01

The textile industry aims to develop fabrics adapted to environmental conditions, in particular to UV radiation. Taking into account the demand for such materials, we prepare an inorganic–organic material, based on ZnO microparticles impregnation of polyester textiles, to perform combined UV-protection properties and high hydrophobicity. Scanning electron microscopy, UV reflectance, Impedance Spectroscopy, contact angle, air permeability, resistance to vapor transfer and tensile strength measurement are used for analysis of the surface and volume properties, related to the performance of the material under environmental conditions, as UV radiation, water and water vapors. The impregnation method ensures a good homogeneity and dispersion of ZnO microparticles into the textile polymeric matrix. The optimum level of impregnation of the fabrics is established to 3–5% ZnO, yielding stable properties, without overloading the fabric. The response of the coated polymer indicates better absorbing the UV radiation and dissipating the surface charge, time stability against UV and higher hydrophobic character, without modification of the mechanical properties, offering enhanced performance and comfort under environmental conditions.

Surface-Plasmon-Enhanced Emissions of Phosphors with Au Nanoparticles Embedded in ITO

Energy Technology Data Exchange (ETDEWEB)

Kim, Ja-Yeon [Korea Photonics Technology Institute (KOPTI), Gwangju (Korea, Republic of); Oh, Seung Jong; Park, Hyun-Sun; Kim, Min-Woo; Cho, Yoo-Hyun; Kwon, Min-Ki [Chosun University, Gwangju (Korea, Republic of)

2017-03-15

Au nanoparticles were embedded in a transparent conducting layer of indium tin oxide in order to evaluate the feasibility of applying a surface-plasmon (SP)-enhanced phosphor to light-emitting diodes (LEDs). The efficiency of the phosphor was improved by energy matching between the phosphor and the SP of the Au nanoparticles. After the density of the Au nanoparticles and the thickness of the spacer layer had been optimized, the efficiency of a green phosphor was improved by 64% compared to that of an isolated green phosphor. This work provides a way to fabricate high-efficiency LEDs with high color-rendering indices and wide color gamuts in white LEDs.

Preparation and Characterization of Fluorinated Hydrophobic UV-Crosslinkable Thiol-Ene Polyurethane Coatings

OpenAIRE

Wenjing Xia; Nianqing Zhu; Rongjie Hou; Wengui Zhong; Mingqing Chen

2017-01-01

The polyurethane prepolymer terminated with a double bond was synthesized using isophorone diisocyanate (IPDI), hydroxyl terminated polybutadiene (HTPB), 1,4-butanediol (BDO), and 2-hydroxyethyl acrylate (HEA). Then, a series of innovative UV-curable polyurethane coatings were prepared by blending ene-terminated polyurethane, fluoroacrylate monomer, and multifunctional thiol crosslinker upon UV exposure. The incorporation of fluoroacrylate monomer and multifunctional thiols into polyurethane ...

Concentration Dependence of Luminescent Properties for Sr2TiO4:Eu3+ Red Phosphor and Its Charge Compensation

Directory of Open Access Journals (Sweden)

Zhou Lu

2012-01-01

Full Text Available Sr2TiO4:Eu3+ phosphors using M+ (M = Li+, Na+, and K+ as charge compensators were prepared by the solid-state reaction. The powders were investigated by powder X-ray diffraction (XRD and photoluminescence spectra (PL to study the phase composition, structure, and luminescent properties. The results showed that Li+ ion was the best charge compensator. The phase was Sr2TiO4 when the doping concentration was small (x≤10.0%. When x reached 15.0%, the phase turned into Sr3Ti3O7 because of the structure damage. The phosphor could be effectively excited by ultraviolet (365, 395 nm and blue light (465 nm, and thenitemitted intense red light that peaked at around 620 nm (5D0→7F2. In addition, the emission of 700 nm (5D0→7F4 enhanced the red light color purity. The CIE chromaticity coordinates of samples with the higher red emission were between (0.650, 0.344 and (0.635, 0.352. Doped layered titanate Sr2TiO4:Eu3+ is a promising candidate red phosphor for white LEDs which can be suited for both near-UV LED chip and blue LED chip.

Gamma radiation induced sensitization and photo-transfer in Mg2SiO4:Tb TLD phosphor

International Nuclear Information System (INIS)

Lakshmanan, A.R.; Vohra, K.G.

1979-01-01

Mg 2 SiO 4 :Tb TLD phosphor was found to show enhanced TL sensitivity to both gamma and UV radiations after high pre-gamma exposures (>100 R) and a post-annealing treatment at 300 0 C for 1 h. Maximum sensitization factors of 2.8 and 55 were obtained at the pre-expsoure levels of 5.2x10 1 C/kg and 1.3x10 3 C/kg for gamma and UV test radiations respectively. The near constancy of the intensity of the residual TL (RTL) peak at 500 0 C for the sensitized sample with increasing test-gamma exposures has ruled out the re-trapping model proposed earlier for the gamma radiation induced sensitization in this phosphor. The Tsub(max) for the sensitized phosphor was found to occur at a higher temperature compared to that for the virgin phosphor. The dependence of sensitization on RTL was explained qualitatively on the basis of competition between sensitization traps (having higher energy than the dosimetry traps) and RTL traps while capturing the charge carriers generated during the test-gamma exposure. The sensitization observed in this phosphor to UV test radiation was found to be a consequence of the photo-transfer of charge carriers from deep (RTL) traps to the shallow (dosimetry) traps. The reduction in RTL peak (500 0 C) intensity of the sensitized sample with increasing test-UV exposure has demonstrated the photo-transfer mechanism in this phosphor. The TL response of the virgin Mg 2 SiO 4 :Tb phosphor was found to be supralinear to both gamma and UV radiations. The TL response of the sensitized phosphor was found to be linear to gamma radiation and sublinear to UV radiation. (Auth.)

340nm UV LED excitation in time-resolved fluorescence system for europium-based immunoassays detection

DEFF Research Database (Denmark)

Rodenko, Olga; Fodgaard, Henrik; Tidemand-Lichtenberg, Peter

2017-01-01

In immunoassay analyzers for in-vitro diagnostics, Xenon flash lamps have been widely used as excitation light sources. Recent advancements in UV LED technology and its advantages over the flash lamps such as smaller footprint, better wall-plug efficiency, narrow emission spectrum......, and no significant afterglow, have made them attractive light sources for gated detection systems. In this paper, we report on the implementation of a 340 nm UV LED based time-resolved fluorescence system based on europium chelate as a fluorescent marker. The system performance was tested with the immunoassay based...... on the cardiac marker, TnI. The same signal-to-noise ratio as for the flash lamp based system was obtained, operating the LED below specified maximum current. The background counts of the system and its main contributors were measured and analyzed. The background of the system of the LED based unit was improved...

Synthesis and photoluminescence study of rare earth activated phosphor Na2La2B2O7

International Nuclear Information System (INIS)

Nagpure, P.A.; Omanwar, S.K.

2012-01-01

The photoluminescence properties in UV and N-UV excitable range for the phosphors of Na 2 La 2 B 2 O 7 : RE (RE=Eu, Tb, Ce, Sm, Gd) are investigated. The solution combustion synthesis technique was employed for the synthesis of the phosphors Na 2 La 2 B 2 O 7 : RE. The photoluminescence measurements of the phosphors were carried out on a HITACHI F7000 Fluorescence Spectrophotometer. The PL and PL excitation (PLE) spectra indicate that the main emission wavelength of Na 2 La 2 B 2 O 7 : Eu are 591 and 615 nm, Na 2 La 2 B 2 O 7 : Ce shows dominating emission peak at 387 nm and Na 2 La 2 B 2 O 7 : Tb displays green emission at 493, 544, 593 and 620 nm at 254 nm excitation, while Na 2 La 2 B 2 O 7 : Sm shows the main emission peak wavelengths 566 and 604 nm at 405 nm excitation and Na 2 La 2 B 2 O 7 : Gd shows dominating emission peak at 312 nm at 274 nm excitation. These phosphors may provide a new kind of luminescent materials under ultraviolet and near ultraviolet excitation for various applications. - Highlights: ► We use the combustion technique for synthesis of Na 2 La 2 B 2 O 7 : RE phosphor. ► Phosphor Na 2 La 2 B 2 O 7 : Eu 3+ shows intense red emission under UV excitation. ► Phosphor Na 2 La 2 B 2 O 7 : Tb 3+ shows intense green emission under UV excitation. ► Phosphor Na 2 La 2 B 2 O 7 : Sm 3+ shows orange red emission under near UV excitation. ► Phosphors Na 2 La 2 B 2 O 7 : Ce 3+ and Na 2 La 2 B 2 O 7 : Gd 3+ show near UV and UVB emissions under UV excitation.

Continuous tunable broadband emission of fluorphosphate glasses for single-component multi-chromatic phosphors.

Science.gov (United States)

Zheng, Ruilin; Zhang, Qi; Yu, Kehan; Liu, Chunxiao; Ding, Jianyong; Lv, Peng; Wei, Wei

2017-10-15

A kind of Sn 2+ /Mn 2+ co-doped fluorphosphate (FP) glasses that served as single-component continuous tunable broadband emitting multi-chromatic phosphors are developed for the first time. Importantly, these FP glasses have high thermal conductivity (3.25-3.70  W/m·K) and good chemical stability in water (80°C). By combining with commercially available UV-LEDs directly, the emission colors can be tuned from blue/cold-white to warm-white/red through the energy transfer from Sn 2+ to Mn 2+ , and the broadband spectra covering the whole visible region from 380 nm to 760 nm. Notably, the FP glass can also serve as a white light phosphor by controlling the content of SnO/MnO, which has excellent optical properties. The CIE chromaticity coordinate, color rendering index, and quantum efficiency are (0.33, 0.29), 84, and 0.952, respectively. These new phosphors, possessing good optical and chemical properties, are promising for applications in solid-state lighting devices.

Natural organic UV-absorbent coatings based on cellulose and lignin: designed effects on spectroscopic properties.

Science.gov (United States)

Hambardzumyan, Arayik; Foulon, Laurence; Chabbert, Brigitte; Aguié-Béghin, Véronique

2012-12-10

Novel nanocomposite coatings composed of cellulose nanocrystals (CNCs) and lignin (either synthetic or fractionated from spruce and corn stalks) were prepared without chemical modification or functionalization (via covalent attachment) of one of the two biopolymers. The spectroscopic properties of these coatings were investigated by UV-visible spectrophotometry and spectroscopic ellipsometry. When using the appropriate weight ratio of CNC/lignin (R), these nanocomposite systems exhibited high-performance optical properties, high transmittance in the visible spectrum, and high blocking in the UV spectrum. Atomic force microscopy analysis demonstrated that these coatings were smooth and homogeneous, with visible dispersed lignin nodules in a cellulosic matrix. It was also demonstrated that the introduction of nanoparticles into the medium increases the weight ratio and the CNC-specific surface area, which allows better dispersion of the lignin molecules throughout the solid film. Consequently, the larger molecular expansion of these aromatic polymers on the surface of the cellulosic nanoparticles dislocates the π-π aromatic aggregates, which increases the extinction coefficient and decreases the transmittance in the UV region. These nanocomposite coatings were optically transparent at visible wavelengths.

A WLED based on LuAG:Ce3+ PiG coated red-emitting K2SiF6:Mn4+ phosphor by screen-printing

Science.gov (United States)

Cao, Rui; Wu, Lingchao; Di, Xiaoxuan; Li, Pengzhi; Hu, Guangcai; Liang, Xiaojuan; Xiang, Weidong

2017-08-01

It is high-profile that the use of phosphor-in-glass (PiG) is extensive because of its excellent advantages in thermal resistance and lifetime aspects, and so on. Here, white light-emitting diodes (WLED) based on LuAG:Ce3+ PiG coated red-emitting K2SiF6:Mn4+ (KSF) phosphors by screen-printing are fabricated. Among all of these, the commercial LuAG phosphors and glass raw materials of TeO2-based glass, were weighted and milled in an agate thoroughly. Then, the mixture was melted and sintered at 850 K or so for 20 min in the ambient atmosphere through low temperature co-fired method, cold-forming LuAG PiG clump and cut into different LuAG PiG thicknesses. After that, the commercial red phosphor KSF was coated on LuAG PiG by screen-printing technique. Finally, high-performance WLEDs based on the TeO2-based glass were obtained, tested and characterized, which exhibit a highest color rendering index of 94.1, a lowest color temperature of 3744 K and a largest luminous efficiency of 101.02 lm·W-1. Most noticeably of all, the promising method has excellent developing potential for industrialization in high-power WLED.

UV curable aqueous dispersions for wood coatings

International Nuclear Information System (INIS)

Peeters, S.; Bleus, J.P.; Wang, Z.J.; Arceneaux, J. A.; Hall, J.

1999-01-01

In this paper the characterisation of aqueous dispersions of UV curable resins is described. Two types of dispersions were used: dispersions that are tacky after water evaporation and tack - free before cure dispersions. The physical and rheological properties of these products have been determined and the performance of these dispersions in various formulations, especially for wood applications has been studied. With these dispersions, it is possible to produce coatings having a good cure speed, good surface hardness and good solvent -, chemical - and water resistance

Tunable emission and the systematic study on energy-transfer properties of Ce{sup 3+}- and Tb{sup 3+}-co-doped Sr{sub 3}(PO{sub 4}){sub 2} phosphors

Energy Technology Data Exchange (ETDEWEB)

Liu, Zhijun [Guangzhou Maritime Institute, Department of Shipping Engineering, Guangzhou (China)

2015-09-15

An emitting color tunable phosphor Sr{sub 3}(PO{sub 4}){sub 2}:Ce{sup 3+}, Tb{sup 3+} was synthesized by the traditional high-temperature solid-state reaction method. The photoluminescence and energy-transfer (ET) properties of Ce{sup 3+}- and Tb{sup 3+}-doped Sr{sub 3}(PO{sub 4}){sub 2} host were studied in detail. The obtained phosphors show both a blue emission from Ce{sup 3+} and a yellowish green emission from Tb{sup 3+} with considerable intensity under ultraviolet (UV) excitation (∝311 nm). When the content of Ce{sup 3+} was fixed at 0.03, the emission chromaticity coordinates could be adjusted from blue to green region by tuning the contents of Tb{sup 3+} ions with the aid of ET process. The critical distance between Ce{sup 3+} and Tb{sup 3+} is 14.69 A. The ET mechanism from Ce{sup 3+} to Tb{sup 3+} ions was identified with dipole-dipole interaction. The obtained phosphor exhibits a strong excitation in UV spectral region and high-efficient ET from Ce{sup 3+} to Tb{sup 3+} ions. It may find applications as a green light-emitting UV-convertible phosphor in white LED devices. (orig.)

Enhancement of heat dissipation of LED module with cupric-oxide composite coating on aluminum-alloy heat sink

International Nuclear Information System (INIS)

Kim, Donghyun; Lee, Junghoon; Kim, Junho; Choi, Chang-Hwan; Chung, Wonsub

2015-01-01

Highlights: • We fabricate the CuO/resin composite coating layer on aluminum alloy heat sink. • CuO/resin coating considerably improved the surface emissivity. • The LED junction temperature was reduced by CuO/resin coated heat sink. • The thermal resistance of heat sink was decreased by CuO/resin composite coating at 200 μm thickness. - Abstract: A composite coating composed of cupric oxide (CuO) and silicon-based resin was applied to an aluminum-alloy heat sink for a light emitting diode (LED) module. The purpose of the composite coating is to improve the heat dissipation performance of heat sink by enhancing thermal radiation emission. The heat dissipation performance was investigated in terms of LED junction temperature and thermal resistance using a thermal transient method. The CuO and silicon-based resin composite coating showed higher emissivity, and the lower junction temperature and thermal resistance of the heat sink was achieved. In addition, a continuous operation test of the LED chip with the heat sink revealed that the surface treated with the CuO composite coating stably dissipated heat without degradation. In conclusion, the composite coating proposed here showed a significant improvement of the heat dissipation performance of the aluminum-alloy heat sink due to the enhanced thermal radiation property.

Evaluating UV-C LED disinfection performance and investigating potential dual-wavelength synergy

Science.gov (United States)

This study evaluated ultraviolet (UV) light emitting diodes (LEDs) emitting at 260 nm, 280 nm, and the combination of 260|280 nm together for their efficacy at inactivating Escherichia. coli, MS2 coliphage, human adenovirus type 2 (HAdV2), and Bacillus pumilus spores; research in...

Mechanical measurements on lithium phosphorous oxynitride coated silicon thin film electrodes for lithium-ion batteries during lithiation and delithiation

Energy Technology Data Exchange (ETDEWEB)

Al-Obeidi, Ahmed, E-mail: alobeidi@mit.edu; Thompson, Carl V., E-mail: reiner.moenig@kit.edu, E-mail: cthomp@mit.edu [Department of Materials Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, Massachusetts 02139 (United States); Kramer, Dominik, E-mail: dominik.kramer@kit.edu; Mönig, Reiner, E-mail: reiner.moenig@kit.edu, E-mail: cthomp@mit.edu [Institute for Applied Materials, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Helmholtz Institute Ulm for Electrochemical Energy Storage (HIU), Helmholtzstraße 11, 89081 Ulm (Germany); Boles, Steven T., E-mail: steven.t.boles@polyu.edu.hk [Institute for Applied Materials, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Hong Kong Polytechnic University, 11 Yuk Choi Rd, Hung Hom (Hong Kong)

2016-08-15

The development of large stresses during lithiation and delithiation drives mechanical and chemical degradation processes (cracking and electrolyte decomposition) in thin film silicon anodes that complicate the study of normal electrochemical and mechanical processes. To reduce these effects, lithium phosphorous oxynitride (LiPON) coatings were applied to silicon thin film electrodes. Applying a LiPON coating has two purposes. First, the coating acts as a stable artificial solid electrolyte interphase. Second, it limits mechanical degradation by retaining the electrode's planar morphology during cycling. The development of stress in LiPON-coated electrodes was monitored using substrate curvature measurements. LiPON-coated electrodes displayed highly reproducible cycle-to-cycle behavior, unlike uncoated electrodes which had poorer coulombic efficiency and exhibited a continual loss in stress magnitude with continued cycling due to film fracture. The improved mechanical stability of the coated silicon electrodes allowed for a better investigation of rate effects and variations of mechanical properties during electrochemical cycling.

Micromachining and dicing of sapphire, gallium nitride and micro LED devices with UV copper vapour laser

International Nuclear Information System (INIS)

Gu, E.; Jeon, C.W.; Choi, H.W.; Rice, G.; Dawson, M.D.; Illy, E.K.; Knowles, M.R.H.

2004-01-01

Gallium nitride (GaN) and sapphire are important materials for fabricating photonic devices such as high brightness light emitting diodes (LEDs). These materials are strongly resistant to wet chemical etching and also, low etch rates restrict the use of dry etching. Thus, to develop alternative high resolution processing and machining techniques for these materials is important in fabricating novel photonic devices. In this work, a repetitively pulsed UV copper vapour laser (255 nm) has been used to machine and dice sapphire, GaN and micro LED devices. Machining parameters were optimised so as to achieve controllable machining and high resolution. For sapphire, well-defined grooves 30 μm wide and 430 μm deep were machined. For GaN, precision features such as holes on a tens of micron length scale have been fabricated. By using this technique, compact micro LED chips with a die spacing 100 and a 430 μm thick sapphire substrate have been successfully diced. Measurements show that the performances of LED devices are not influenced by the UV laser machining. Our results demonstrate that the pulsed UV copper vapour laser is a powerful tool for micromachining and dicing of photonic materials and devices

Thermal properties and flame retardancy of an ether-type UV-cured polyurethane coating

Directory of Open Access Journals (Sweden)

2010-09-01

Full Text Available A new UV-reactive monomer piperazine-N,N′-bis(acryloxyethylaryl-phosphoramidate (N-PBAAP containing phosphorus and nitrogen was synthesized and used as flame retardant for an ether-type UV-cured polyurethane acrylate (PUA coating. The thermal properties of the PUA films were investigated by thermogravimetric analysis (TGA in air and nitrogen atmosphere. The TGA results showed that the incorporation of N-PBAAP can obviously enhance the char residue of the PUA coatings. From the TGA and real time Fourier transformed infrared spectroscopy (RT-FTIR results, different degradation behaviors were observed in the PUA coatings with different N-PBAAP content. The combustibility of the PUA coatings was evaluated by microscale combustion calorimeter (MCC. The MCC results revealed that the addition of NPBAAP in the coatings can significantly reduce the peak Heat Release Rate (pHRR, Heat Release Capacity (HRC and the Total Heat Release (THR of the samples. Furthermore, dynamical mechanical thermal analysis (DMA was employed to examine the viscoelastic properties of the PUA films. It was found that the incorporation of N-PBAAP in the formulation can bring in more functional groups to the coatings, which results in an increase of the glass transition temperature (Tg and cross linking density (XLD of the films.

340nm UV LED excitation in time-resolved fluorescence system for europium-based immunoassays detection

Science.gov (United States)

Rodenko, Olga; Fodgaard, Henrik; Tidemand-Lichtenberg, Peter; Pedersen, Christian

2017-02-01

In immunoassay analyzers for in-vitro diagnostics, Xenon flash lamps have been widely used as excitation light sources. Recent advancements in UV LED technology and its advantages over the flash lamps such as smaller footprint, better wall-plug efficiency, narrow emission spectrum, and no significant afterglow, have made them attractive light sources for gated detection systems. In this paper, we report on the implementation of a 340 nm UV LED based time-resolved fluorescence system based on europium chelate as a fluorescent marker. The system performance was tested with the immunoassay based on the cardiac marker, TnI. The same signal-to-noise ratio as for the flash lamp based system was obtained, operating the LED below specified maximum current. The background counts of the system and its main contributors were measured and analyzed. The background of the system of the LED based unit was improved by 39% compared to that of the Xenon flash lamp based unit, due to the LEDs narrower emission spectrum and longer pulse width. Key parameters of the LED system are discussed to further optimize the signal-to-noise ratio and signal-to-background, and hence the sensitivity of the instrument.

Combination of carbon dot and polymer dot phosphors for white light-emitting diodes.

Science.gov (United States)

Sun, Chun; Zhang, Yu; Sun, Kai; Reckmeier, Claas; Zhang, Tieqiang; Zhang, XiaoYu; Zhao, Jun; Wu, Changfeng; Yu, William W; Rogach, Andrey L

2015-07-28

We realized white light-emitting diodes with high color rendering index (85-96) and widely variable color temperatures (2805-7786 K) by combining three phosphors based on carbon dots and polymer dots, whose solid-state photoluminescence self-quenching was efficiently suppressed within a polyvinyl pyrrolidone matrix. All three phosphors exhibited dominant absorption in the UV spectral region, which ensured the weak reabsorption and no energy transfer crosstalk. The WLEDs showed excellent color stability against the increasing current because of the similar response of the tricolor phosphors to the UV light variation.

Blue-emitting LaSi3N5:Ce3+ fine powder phosphor for UV-converting white light-emitting diodes

Science.gov (United States)

Suehiro, Takayuki; Hirosaki, Naoto; Xie, Rong-Jun; Sato, Tsugio

2009-08-01

We have synthesized the pure ternary nitride phosphor, LaSi3N5:Ce3+ from the multicomponent oxide system La2O3-CeO2-SiO2, by using the gas-reduction-nitridation method. Highly pure, single-phase LaSi3N5:Ce3+ powders possessing particle sizes of ˜0.4-0.6 μm were obtained with the processing temperature ≤1500 °C. The synthesized LaSi3N5:Ce3+ exhibits tunable blue broadband emission with the dominant wavelength of 464-475 nm and the external quantum efficiency of ˜34%-67% under excitation of 355-380 nm. A high thermal stability of LaSi3N5:Ce3+ compared to the existing La-Si-O-N hosts was demonstrated, indicating the promising applicability as a blue-emitting phosphor for UV-converting white light-emitting diodes.

Rare-earth doped gadolinia based phosphors for potential multicolor and white light emitting deep UV LEDs.

Science.gov (United States)

Bedekar, Vinila; Dutta, Dimple P; Mohapatra, M; Godbole, S V; Ghildiyal, R; Tyagi, A K

2009-03-25

Gadolinium oxide host and europium/dysprosium/terbium doped gadolinium oxide nanoparticles were synthesized using the sonochemical technique. Gadolinium oxide nanocrystals were also co-doped with total 2 mol% of Eu(3+)/Dy(3+),Eu(3+)/Tb(3+),Dy(3+)/Tb(3+), and also Eu(3+)/Dy(3+)/Tb(3+) ions, by the same method. The nanoparticles obtained were characterized using powder x-ray diffraction (XRD), transmission electron microscopy (TEM), and selected area electron diffraction (SAED) techniques. The size of the particles ranged from 15 to 30 nm. The triple doped samples showed multicolor emission on single wavelength excitation. The photoluminescence results were correlated with the lifetime data to get an insight into the luminescence and energy transfer processes taking place in the system. On excitation at 247 nm, the novel nanocrystalline Gd(2)O(3):RE (RE = Dy, Tb) phosphor resulted in having very impressive CIE chromaticity coordinates of x = 0.315 and y = 0.316, and a correlated color temperature of 6508 K, which is very close to standard daylight.

Photoluminescence properties and energy-transfer of thermal-stable Ce3+, Mn2+-codoped barium strontium lithium silicate red phosphors

International Nuclear Information System (INIS)

Zhang Xinguo; Gong Menglian

2011-01-01

Research highlights: → Excited by UV, strong red luminescence is observed from Ce 3+ , Mn 2+ -codoped barium strontium lithium silicate (BSLS), while violet-blue emission from Ce 3+ sole doped BSLS. → These results indicate the Mn 2+ -derived red emission is originated by an efficient Ce 3+ → Mn 2+ energy transfer. → The red emission becomes stronger with increased Sr content, and shows red-shift. → These phosphors demonstrate good thermal stability even in 180 o C, which is suitable for NUV LED application. - Abstract: A series of thermal-stable Ce 3+ , Mn 2+ -codoped barium strontium lithium silicate (BSLS) phosphors was synthesized by a high-temperature solid-state reaction. The XRD patterns of this phosphor seem to be a new phase that has not been reported before. BSLS:Ce 3+ , Mn 2+ showed two emission bands under 365 nm excitation: one observed at 421 nm was attributed to Ce 3+ emission, and the other found in red region was assigned to Mn 2+ emission through Ce 3+ -Mn 2+ efficient energy transfer. The Mn 2+ emission shifted red along with the replacement of barium by strontium, which was due to the change of crystal field. A composition-optimized phosphor, BSLS:0.10Ce 3+ , 0.05Mn 2+ (Ba = 65), exhibited strong and broad red-emitting and supreme thermal stability. The results suggest that this phosphor is suitable as a red component for NUV LED or high pressure Hg vapor (HPMV) lamp.

Luminescence and Luminescence Quenching of K2Bi(PO4)(MoO4):Eu3+ Phosphors with Efficiencies Close to Unity.

Science.gov (United States)

Grigorjevaite, Julija; Katelnikovas, Arturas

2016-11-23

A very good light emitting diode (LED) phosphor must have strong absorption, high quantum efficiency, high color purity, and high quenching temperature. Our synthesized K 2 Bi(PO 4 )(MoO 4 ):Eu 3+ phosphors possess all of the mentioned properties. The excitation of these phosphors with the near-UV or blue radiation results in a bright red luminescence dominated by the 5 D 0 → 7 F 2 transition at ∼615 nm. Color coordinates are very stable when changing Eu 3+ concentration or temperature in the range of 77-500 K. Furthermore, samples doped with 50% and 75% Eu 3+ showed quantum efficiencies close to 100% which is a huge benefit for practical application. Temperature dependent luminescence measurements showed that phosphor performance increases with increasing Eu 3+ concentration. K 2 Eu(PO 4 )(MoO 4 ) sample at 400 K lost only 20% of the initial intensity at 77 K and would lose half of the intensity only at 578 K. Besides, the ceramic disks with thicknesses of 0.33 and 0.89 mm were prepared from K 2 Eu(PO 4 )(MoO 4 ) powder, and it turned out that they efficiently converted the radiation of 375 nm LED to the red light. The conversion of 400 nm LED radiation to the red light was not complete; thus, the light sources with various tints of purple color were obtained. The combination of ceramic disks with 455 nm LED yielded the light sources with tints of blue color due to the low absorption of ceramic disk in this spectral range. In addition, these phosphors possess a very unique emission spectra; thus, they could also be applied in luminescent security pigments.

Investigation on optical band gap, photoluminescence properties and concentration quenching mechanism of Pb1 - x Tb3 +xWO4 green-emitting phosphors

Science.gov (United States)

Chanu, Thokchom Taru Taru; Rajmuhon Singh, N.

2018-02-01

A series of monophasic Tb3 + (2, 5, 7, 10 and 15 at%) doped PbWO4 phosphors were successfully prepared via hydrothermal method. X-ray diffraction patterns revealed that the prepared samples possess a high crystallinity with tetragonal scheelite-type structure. FT-IR and Raman analysis exhibited a Wsbnd O stretching peak of WO42 - group, which is also related to the scheelite structure. UV-visible diffuse reflectance spectra indicated a reduction in the optical band gap with the replacement of Pb2 + by Tb3 + ions. The presence of strong and intense emission peaks characteristic of Tb3 + with the dominant peak at 545 nm (green, 5D4 → 7F5 transition) under UV irradiation at 320 nm demonstrated an efficient energy transfer from the host to Tb3 + ions. Using Van Uitert's model, the concentration quenching mechanism between Tb3 + ions in PbWO4:Tb3 + phosphor was attributed to a dipole-dipole interaction and the critical distance was determined to be 12 Å. The decay lifetimes and CIE chromaticity co-ordinates of PbWO4:Tb3 + phosphors were also investigated in detail. These prepared materials might serve as a potential phosphor for LED applications.

Aluminum Mirror Coatings for UVOIR Telescope Optics Including the Far UV

Science.gov (United States)

Balasubramanian, Kunjithapatha; Hennessy, John; Raouf, Nasrat; Nikzad, Shouleh; Ayala, Michael; Shaklan, Stuart; Scowen, Paul; Del Hoyo, Javier; Quijada, Manuel

2015-01-01

NASA Cosmic Origins (COR) Program identified the development of high reflectivity mirror coatings for large astronomical telescopes particularly for the far ultra violet (FUV) part of the spectrum as a key technology requiring significant materials research and process development. In this paper we describe the challenges and accomplishments in producing stable high reflectance aluminum mirror coatings with conventional evaporation and advanced Atomic Layer Deposition (ALD) techniques. We present the current status of process development with reflectance of approx. 55 to 80% in the FUV achieved with little or no degradation over a year. Keywords: Large telescope optics, Aluminum mirror, far UV astrophysics, ALD, coating technology development.

Investigation of the effect of UV-LED exposure conditions on the production of vitamin D in pig skin

DEFF Research Database (Denmark)

Barnkob, Line Lundbæk; Argyraki, Aikaterini; Petersen, Paul Michael

2016-01-01

study the exposure conditions with ultraviolet (UV) LEDs were systematically investigated in the wavelength range 280-340 nm for achieving optimal vitamin D bio-fortification in pig skin. A wavelength of 296 nm was found to be optimal for vitamin D3 production. The maximum dose of 20 kJ/m2 produced 3.......5-4 µg vitamin D3/cm2 pig skin. Vitamin D3 produced was independent on the combination of time and intensity of the LED source. The increased UV exposure by UV-LEDs may be readily implemented in existing food production facilities, without major modifications to the process or processing equipment......The dietary intake of vitamin D is currently below the recommended intake of 10-20 µg vitamin D/day. Foods with increased content of vitamin D or new products with enhanced vitamin D are warranted. Light-emitting diodes (LEDs) are a potential new resource in food production lines. In the present...

Thermoluminescence glow curve for UV induced ZrO2:Ti phosphor with variable concentration of dopant and various heating rate

Directory of Open Access Journals (Sweden)

Neha Tiwari

2014-10-01

Full Text Available The present paper reports the synthesis and characterization of Ti doped ZrO2 nanophosphors. The effects of variable concentration of titanium on thermoluminescence (TL behaviour are studied. The samples were prepared by combustion a synthesis technique which is suitable for less time taking techniques also for large scale production for nano phosphors. The starting material used for sample preparation are Zr(NO33 and Ti(NO33 and urea used as a fuel. The prepared sample was characterized by X-ray diffraction technique (XRD with variable concentration of Ti (0.05–0.5 mol% there is no any phase change found with increase the concentration of Ti. Sample shows cubic structure and the particle size calculated by Scherer's formula. The surface morphology of prepared phosphor was determined by field emission gun scanning electron microscopy (FEGSEM technique for optimized concentration of dopant. The good connectivity with grains and the semi-sphere like structure was found by FEGSEM. The functional group analysis was determined by Fourier transform infrared (FTIR spectroscopic techniques. The prepared phosphor examined by thermoluminescence technique. For recording TL glow curve every time 2 mg phosphor was irradiated by UV 254 nm source and fixed the heating rate at 5 °C s−1. Sample shows well resolved peak at 167 °C with a shoulder peak at 376 °C. The higher temperature peak shows the well stability and less fading in prepared phosphor. Also the effect of Ti concentration at fixed UV exposure time was studied. The effect of UV exposure time and dose versus intensity plot was studied. Sample shows linear response with dose and broaden peak with high temperature shows the more stability and less fading in TL glow curve. The linear dose response, high stability and less fading phenomenon shows the sample may be useful for thermoluminescence dosimetry application. Trapping parameters are calculated for every recorded glow curve. The

Removal of sulfamethoxazole, ibuprofen and nitrobenzene by UV and UV/chlorine processes: A comparative evaluation of 275 nm LED-UV and 254 nm LP-UV.

Science.gov (United States)

Kwon, Minhwan; Yoon, Yeojoon; Kim, Seonbaek; Jung, Youmi; Hwang, Tae-Mun; Kang, Joon-Wun

2018-05-15

The aim of this study is to evaluate the micropollutant removal capacity of a 275 nm light-emitting diode (LED)-UV/chlorine system. The sulfamethoxazole, ibuprofen, and nitrobenzene removal efficiencies of this system were compared with those of a conventional 254 nm low-pressure (LP)-UV system as a function of the UV dose. In a direct photolysis system, the photon reactivity of sulfamethoxazole is higher than that of nitrobenzene and ibuprofen at both wavelengths. The molar absorption coefficients and quantum yields of each micropollutant were as follows: sulfamethoxazole (ε SMX, 275 nm protonated  = 17,527 M -1  cm -1 , Φ SMX, 275 nm protonated  = 0.239, ε SMX, 275 nm deprotonated  = 8430 M -1  cm -1 , and Φ SMX, 275 nm deprotonated  = 0.026), nitrobenzene (ε NB, 275 nm  = 7176 M -1  cm -1 and Φ NB, 275 nm  = 0.057), and ibuprofen (ε NB, 275 nm  = 200 M -1  cm -1 and Φ IBF, 275 nm  = 0.067). The photon reactivity of chlorine species, i.e., HOCl and OCl-, were determined at 275 nm (ε HOCl, 275 nm  = 28 M -1  cm -1 , Φ HOCl, 275 nm  = 1.97, ε OCl-, 275 nm  = 245 M -1  cm -1 , and Φ OCl-, 275 nm  = 0.8), which indicate that the decomposition rate of OCl - is higher and that of HOCl is lower by 275 nm photolysis than that by 254 nm photolysis (ε HOCl, 254 nm  = 60 M -1  cm -1 , Φ HOCl, 254 nm  = 1.46, ε OCl-, 254 nm  = 58 M -1  cm -1 , and Φ OCl-, 254 nm  = 1.11). In the UV/chlorine system, the removal rates of ibuprofen and nitrobenzene were increased by the formation of OH and reactive chlorine species. The 275-nm LED-UV/chlorine system has higher radical yields at pH 7 and 8 than the 254 nm LP-UV/chlorine system. Copyright © 2018 Elsevier B.V. All rights reserved.

Fluorescence image excited by a scanning UV-LED light

Science.gov (United States)

Tsai, Hsin-Yi; Chen, Yi-Ju; Huang, Kuo-Cheng

2013-03-01

An optical scanning system using UV-LED light to induced fluorescence technology can enhance a fluorescence image significantly in a short period. It has several advantages such as lower power consumption, no scattering effect in skins, and multilayer images can be obtained to analyze skin disease. From the experiment results, the light intensity increases with increase spot size and decrease scanning speed, but the image resolution is oppositely. Moreover, the system could be widely used in clinical diagnosis and photodynamic therapy for skin disease because even the irradiated time of fluorescence substance is short but it will provide accurately positioning of fluorescence object.

Synthesis, structure, and luminescence properties of SrSiAl2O3N2:Eu(2+) phosphors for light-emitting devices and field emission displays.

Science.gov (United States)

Wang, Xicheng; Zhao, Zhengyan; Wu, Quansheng; Li, Yanyan; Wang, Chuang; Mao, Aijun; Wang, Yuhua

2015-06-28

A series of SrSiAl2O3N2:Eu(2+) (0.005 ≤x≤ 0.05) phosphors were successfully synthesized through a pressureless, facile, and efficient solid state route. The crystal structure, band structure, and their photoluminescence and cathodoluminescence properties were investigated in detail. The phosphors exhibit rod shape morphology with a uniform Eu(2+) distribution. Under n-UV excitation the emission spectra shift from 477 to 497 nm with an increase of Eu(2+) concentration. The concentration quenching mechanism of Eu(2+) emission was dominated by the dipole-dipole interaction. The thermal stability is comparable to that of the commercial Ba2SiO4:Eu(2+) phosphor. The phosphor also exhibits high current saturation and high resistance under low voltage electron bombardment. All the results indicate that the SrSiAl2O3N2:Eu(2+) phosphors can be considered as candidates for application in both white LEDs and FEDs.

Lu{sub 3}(Al,Si){sub 5}(O,N){sub 12}:Ce{sup 3+} phosphors with broad emission band and high thermal stability for white LEDs

Energy Technology Data Exchange (ETDEWEB)

Liu, Jiaqing; Wang, Xiaojun; Xuan, Tongtong; Wang, Chunbo; Li, Huili, E-mail: hlli@phy.ecnu.edu.cn; Sun, Zhuo

2015-02-15

A yellow-orange emitting Lu{sub 3}Al{sub 5−x}Si{sub x}O{sub 12−x}N{sub x}:Ce{sup 3+} phosphor with excellent color rendering, high luminescent efficiency and high thermal stability was reported in this paper. It was synthesized by a conventional solid-state reaction method. The effect of Si{sup 4+}–N{sup 3−} incorporation on the optical properties of Lu{sub 3}Al{sub 5}O{sub 12}:Ce{sup 3+} phosphor was investigated and compared to YAG:Ce{sup 3+} with the same compositions. Similarly, the addition of α-Si{sub 3}N{sub 4} leads to a distinct redshift and broadening of photoluminescent spectrum, which is assigned to the increased covalency and crystal field strength caused by N{sup 3−}. Nevertheless, an excellent thermal stability and a higher integrated intensity presented by α-Si{sub 3}N{sub 4}-doped LuAG:Ce{sup 3+} are distinctive. Further, the emission intensity can be greatly enhanced by adding NaF flux. Finally, the white LED flat lamp with a CRI as high as 83 and a luminous efficiency of 85 lm/W is successfully realized by using a single LuAG-based oxynitride phosphor combined with a blue LED chip, which is completely feasible for general indoor illuminations to replace the traditional fluorescent or incandescent lamps. - Highlights: • Si{sub 3}N{sub 4}-doped LuAG:Ce{sup 3+} oxynitride phosphors were synthesized by a solid-state reaction. • The effect of Si{sup 4+}–N{sup 3−} incorporation on the optical properties was investigated. • The addition of Si{sub 3}N{sub 4} leads to an obvious redshift of the emission spectra. • Lu{sub 3}Al{sub 5−x}Si{sub x}O{sub 12−x}N{sub x}:Ce{sup 3+} shows an excellent thermal stability and a higher intensity. • A warm white LED with CRI=83 is achieved by a single oxynitride phosphor.

[Investigation of multi-wavelength effect during the measurement of UV-enhanced film's emission spectrum].

Science.gov (United States)

Liu, Meng; Ni, Zheng-ji; Zhang, Da-wei; Huang, Yuan-shen; Zhuang, Song-lin

2009-09-01

The UV-responsive detector is a dual-use device for civilian and military after the laser and IR-responsive sensors. Typical image sensor coated with a layer of down-convert frequency thin film on it's photosurface to enhance UV response is the key technology of enhancing UV-response. The UV-enhanced thin film was made in the experimental laboratory using the Zn2SiO4:Mn phosphor by spin coating method. Two peaks at 520 and 560 nm respectively in the emission spectrum of the UV-enhanced film were found by SP1702 spectrograph when the excitation wavelength was 260 and 280 nm. The peaks were found in the process of experiment of measuring and counting the quantum efficiency of UV-enhanced thin film. But the light peaks at 520 and 560 nm are not the emission light peaks by the exciting light of 260 and 280 nm. The reason why the light at 520 and 560 nm is not the emission light was analyzed based on the measurement principle of grating spectrograph. The reasons for the multi-wavelength of light overlaps during the measurement of emission spectrum were also discussed. And the equipment used to separate the overlapped different wavelengths was designed, which will be used to resolve the problem of the overlap of multi-wavelength.

Investigation of thermoluminescence and electron-vibrational interaction parameters in SrAl2O4:Eu2+, Dy3+ phosphors

International Nuclear Information System (INIS)

Pardhi, Shilpa A.; Nair, Govind B.; Sharma, Ravi; Dhoble, S.J.

2017-01-01

Combustion synthesis method was employed for the synthesis of green-emitting monoclinic SrAl 2 O 4 :Eu 2+ , Dy 3+ phosphors. The phase-purity of the prepared phosphors were examined using X-ray diffraction (XRD). The prepared phosphors exhibited green light emission with the peak centred at 510 nm, under 350 nm UV excitation. The excitation and emission spectra were analysed and the parameters of electron-vibrational interaction (EVI), such as the Huang–Rhys factor, effective phonon energy and zero-phonon line position were estimated using the spectrum fitting method. Thermoluminescence (TL) behaviour of the as-prepared phosphors were analysed for UV and 137 Cs γ-ray source irradiation. TL glow curves for UV-irradiated SrAl 2 O 4 :Eu 2+ , Dy 3+ phosphors were analysed. - Highlights: • Photoluminescence and thermoluminescence properties of SrAl 2 O 4 :Eu 2+ ,Dy 3+ phosphors were analysed. • Electron-vibrational interaction (EVI) parameters of SrAl 2 O 4 :Eu 2+ ,Dy 3+ phosphors were determined. • The phosphors are found to exhibit green light emission.

Experiment of solidifying photo sensitive polymer by using UV LED

Science.gov (United States)

Kang, Byoung Hun; Shin, Sung Yeol

2008-11-01

The development of Nano/Micro manufacturing technologies is growing rapidly and in the same manner, the investments in these areas are increasing. The applications of Nano/Micro technologies are spreading out to semiconductor production technology, biotechnology, environmental engineering, chemical engineering and aerospace. Especially, SLA is one of the most popular applications which is to manufacture 3D shaped microstructure by using UV laser and photo sensitive polymer. To make a high accuracy and precision shape of microstructures that are required from the diverse industrial fields, the information of interaction relationship between the photo resin and the light source is necessary for further research. Experiment of solidifying photo sensitive polymer by using UV LED is the topic of this paper and the purpose of this study is to find out what relationships do the reaction of the resin have in various wavelength, power of the light and time.

In-situ metrology in multiwafer reactors during MOVPE of AIN-based UV-LEDs (Conference Presentation)

Science.gov (United States)

Knauer, Arne; Brunner, Frank; Kolbe, Tim; Hagedorn, Sylvia; Kueller, Viola; Weyers, Markus

2017-02-01

UV-LEDs are of great interest for applications like disinfection, gas sensing, and phototherapy. The cost sensitive LEDs are commonly grown by MOVPE on transparent AlN/sapphire templates. The large thermal and lattice mismatch between AlN and sapphire generates a very high dislocation density (DD) and causes big challenges in strain management. The threading dislocation density should be reduced to the order of low 108cm-2 for high internal efficiency of the AlGaN based UV-LED structures. The TDD will be reduced mainly by dislocation annihilation during the growth of thick Al(Ga)N layers, which is a challenge in terms of strain management. We present how in-situ reflectometry and curvature measurement (EpiCurveTT(at)LayTec) in commercial multiwafer growth reactors helps to optimize the growth processes concerning growth rates, surface roughening and avoidance of layer cracking on 2inch substrates and enhance the reproducibility of epitaxial growth. The growth of up to 3 μm thick planar AlN templates and up-to 10 μm thick AlN/sapphire templates by epitaxial lateral overgrowth of stripe patterned templates for UV-C LED structures will be highlighted. The implementation of different types of AlN/GaN superlattices for the subsequent growth of up to 5μm thick Al0.5Ga0.5N layer for UVB LED structures will be shown. Correlations to ex-situ measurements like X-ray diffraction and TEM analysis of defects in the LED structures will be shown. Some challenges of in-situ control through very narrow viewports as in Close Coupled Showerhead reactors will be discussed as well as the influence of silicon doping on curvature and dislocation density in Al(Ga)N layers.

Improved performance of UV-LED by p-AlGaN with graded composition

KAUST Repository

Yan, Jianchang; Wang, Junxi; Cong, Peipei; Sun, Lili; Liu, Naixin; Liu, Zhe; Zhao, Chao; Li, Jinmin

2010-01-01

force microscopy image shows that the AlN surface is very flat, while high resolution X-ray diffraction results prove the good crystalline quality of the AlN template. A novel structure UV-LED which has several p-AlGaN layers with graded composition

Luminescence properties of CdSiO3:Mn2+ phosphor

International Nuclear Information System (INIS)

Lei Bingfu; Liu Yingliang; Ye Zeren; Shi Chunshan

2004-01-01

A novel long-lasting phosphor CdSiO 3 :Mn 2+ is reported in this paper. The Mn 2+ -doped CdSiO 3 phosphor emits orange light with CIE chromaticity coordinates x=0.5814 and y=0.4139 under 254 nm UV light excitation. In the emission spectrum of 1% Mn 2+ -doped CdSiO 3 phosphor, there is a broad emission band centered at 575 nm which can be attributed to the spin-forbidden transition of the d-orbital electron associated with the Mn 2+ ion. The phosphorescence can be seen by the naked eyes in the dark clearly even after the 254 nm UV irradiation have been removed for about 1 h. The mechanism of the origin of the long-lasting phosphorescence was discussed using the thermoluminescence curves

One-Step Preparation of Blue-Emitting (La,Ca)Si3(O,N)5:Ce3+ Phosphors for High-Color Rendering White Light-Emitting Diodes

Science.gov (United States)

Yaguchi, Atsuro; Suehiro, Takayuki; Sato, Tsugio; Hirosaki, Naoto

2011-02-01

Highly phase-pure (La,Ca)Si3(O,N)5:Ce3+ blue-emitting phosphors were successfully synthesized via the one-step solid-state reaction from the system La2O3-CaO-CeO2-Si3N4. The synthesized (La,Ca)Si3(O,N)5:Ce3+ exhibits tunable blue broadband emission with the dominant wavelength of 466-479 nm and the external quantum efficiency up to ˜45% under 380 nm near-UV (NUV) excitation. Spectral simulations of the trichromatic white light-emitting diodes (LEDs) using (La,Ca)Si3(O,N)5:Ce3+ demonstrated markedly higher color rendering index Ra values of 93-95, compared to 76-90 attained by the systems using a conventional BAM:Eu2+ phosphor or InGaN blue LED. The present achievement indicates the promising applicability of (La,Ca)Si3(O,N)5:Ce3+ as a blue luminescent source for NUV-converting high-color rendering white LEDs.

Photocatalytic Activity and Optical Properties of Blue Persistent Phosphors under UV and Solar Irradiation

Directory of Open Access Journals (Sweden)

C. R. García

2016-01-01

Full Text Available Blue phosphorescent strontium aluminosilicate powders were prepared by combustion synthesis route and a postannealing treatments at different temperatures. X-ray diffraction analysis showed that phosphors are composed of two main hexagonal phases: SrAl2O4 and Sr3Al32O51. The morphology of the phosphors changed from micrograins (1000°C to a mixture of bars and hexagons (1200°C and finally to only hexagons (1300°C as the annealing temperature is increased. Photoluminescence spectra showed a strong blue-green phosphorescent emission centered at λem=455 nm, which is associated with 4f65d1→4f6  (8S7/2 transition of the Eu2+. The sample annealed at 1200°C presents the highest luminance value (40 Cd/m2 with CIE coordinates (0.1589, 0.1972. Also, the photocatalytic degradation of methylene blue (MB under UV light (at 365 nm was monitored. Samples annealed at 1000°C and 1300°C presented the highest percentage of degradation (32% and 38.5%, resp. after 360 min. In the case of photocatalytic activity under solar irradiation, the samples annealed at 1000°C, 1150°C, and 1200°C produced total degradation of MB after only 300 min. Hence, the results obtained with solar photocatalysis suggest that our powders could be useful for water cleaning in water treatment plants.

Bluish-White Luminescence in Rare-Earth-Free Vanadate Garnet Phosphors: Structural Characterization of LiCa3MV3O12 (M = Zn and Mg).

Science.gov (United States)

Hasegawa, Takuya; Abe, Yusuke; Koizumi, Atsuya; Ueda, Tadaharu; Toda, Kenji; Sato, Mineo

2018-01-16

Extensive attention has been focused toward studies on inexpensive and rare-earth-free garnet-structure vanadate phosphors, which do not have a low optical absorption due to the luminescence color being easily controlled by its high composition flexibility. However, bluish emission phosphors with a high quantum efficiency have not been found until now. In this study, we successfully discovered bluish-white emitting, garnet structure-based LiCa 3 MV 3 O 12 (M = Zn and Mg) phosphors with a high quantum efficiency, and the detailed crystal structure was refined by the Rietveld analysis technique. These phosphors exhibit a broad-band emission spectra peak at 481 nm under near UV-light excitation at 341 nm, indicating no clear difference in the emission and excitation spectra. A very compact tetrahedral [VO 4 ] unit is observed in the LiCa 3 MV 3 O 12 (M = Zn and Mg) phosphors, which is not seen in other conventional garnet compounds, and generates a bluish-white emission. In addition, these phosphors exhibit high quantum efficiencies of 40.1% (M = Zn) and 44.0% (M = Mg), respectively. Therefore, these vanadate garnet phosphors can provide a new blue color source for LED devices.

A new UV-LED device for automatic disinfection of stethoscope membranes.

Science.gov (United States)

Messina, Gabriele; Burgassi, Sandra; Messina, Daniele; Montagnani, Valerio; Cevenini, Gabriele

2015-10-01

Stethoscopes are widely used by doctors and nurses. Poor stethoscope hygiene is a potential source of nosocomial infection. This study aimed to propose an innovative solution, based on the latest advances in ultraviolet (UV) light-emitting diodes (LEDs), for disinfecting stethoscope membranes automatically and efficiently. Staphylococcus aureus, Escherichia coli, Pseudomonas aeruginosa, and Enterococcus faecalis were sown on 28 stethoscope membranes and then transferred to Petri dishes. Treatment involved illuminating exposed Petri dishes with a UVC LED for 1 minute. For each microbe, the number of colony-forming units (cfu) at 36°C was compared in control and treated dishes using the Wilcoxon signed-rank test. The Kruskal-Wallis test was used to assess percent reductions in bacteria. Statistical significance was set at 99%. A significant reduction in cfu counts after UV treatment (P  .01). The stethoscope, symbol of medicine and health care professionals, has been demonstrated to be a carrier of microorganisms. The treatment technique was effective and efficient in disinfecting the membranes. These promising results represent a step forward toward eliminating stethoscope membrane contamination with an innovative approach. Copyright © 2015 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Photoluminescence in Sm3+ doped Ba2P2O7 phosphor prepared by solution combustion method

Science.gov (United States)

Ghawade, Sonal P.; Deshmukh, Kavita A.; Dhoble, S. J.; Deshmukh, Abhay D.

2018-05-01

In this paper, Sm3+ doped Ba2P2O7 phosphors were synthesized via a Solution combustion method. The crystal structure of the phosphor was characterized by XRD. Orange-red emission was observed from these phosphors under near-ultraviolet (UV) excitation at 404 nm. The luminescence properties of the obtained phosphors were characterized by different techniques. The Ba2P2O7:Sm3+ phosphor can be efficiently excited by near-UV and blue light, and their emission spectrum consists of three emission peaks, at 564, 602, and 646 nm, respectively. Based on the results, the as prepared Ba2P2O7:Sm3+ phosphors are promising orange-red-emitting phosphors exhibit great potential may be applicable as a spectral convertor in c-Si solar cell to enhance the efficiency of solar cell in future.

Characterization of 380nm UV-LEDs grown on free-standing GaN by atmospheric-pressure metal-organic chemical vapor deposition

Science.gov (United States)

Shieh, C. Y.; Li, Z. Y.; Kuo, H. C.; Chang, J. Y.; Chi, G. C.

2014-03-01

We reported the defects and optical characterizations of the ultraviolet light-emitting diodes grown on free-standing GaN substrate (FS-GaN) and sapphire. Cross-sectional transmission electron microscopy (TEM) images showed that the total defect densities of grown UV LEDs on FS-GaN and sapphire including edge, screw and mixed type were 3.6×106 cm-2 and 5.5×108 cm-2. When substrate of UV LEDs was changed from sapphire to FS-GaN, it can be clearly found that the crystallography of GaN epilayers was drastically different from that GaN epilayers on sapphire. Besides, the microstructures or indium clustering can be not observed at UV LEDs on FS-GaN from TEM measurement. The internal quantum efficiency of UVLEDs on FS-GaN and sapphire were 34.8 % and 39.4 % respectively, which attributed to indium clustering in multi-layers quantum wells (MQWs) of UV LEDs on sapphire. The relationship between indiumclustering and efficiency droop were investigated by temperature-dependent electroluminescence (TDEL) measurements.

High-Power 365 nm UV LED Mercury Arc Lamp Replacement for Photochemistry and Chemical Photolithography

OpenAIRE

H?lz, K.; Lietard, J.; Somoza, M. M.

2016-01-01

Ultraviolet light emitting diodes (UV LEDs) have become widespread in chemical research as highly efficient light sources for photochemistry and photopolymerization. However, in more complex experimental setups requiring highly concentrated light and highly spatially resolved patterning of the light, high-pressure mercury arc lamps are still widely used because they emit intense UV light from a compact arc volume that can be efficiently coupled into optical systems. Advances in the deposition...

Quantitative analysis of UV excitation bands for red emissions in Pr3+-doped CaTiO3, SrTiO3 and BaTiO3 phosphors by peak fitting

International Nuclear Information System (INIS)