Influence of Anchoring on Burial Depth of Submarine Pipelines.

Directory of Open Access Journals (Sweden)

Yuan Zhuang

Full Text Available Since the beginning of the twenty-first century, there has been widespread construction of submarine oil-gas transmission pipelines due to an increase in offshore oil exploration. Vessel anchoring operations are causing more damage to submarine pipelines due to shipping transportation also increasing. Therefore, it is essential that the influence of anchoring on the required burial depth of submarine pipelines is determined. In this paper, mathematical models for ordinary anchoring and emergency anchoring have been established to derive an anchor impact energy equation for each condition. The required effective burial depth for submarine pipelines has then been calculated via an energy absorption equation for the protection layer covering the submarine pipelines. Finally, the results of the model calculation have been verified by accident case analysis, and the impact of the anchoring height, anchoring water depth and the anchor weight on the required burial depth of submarine pipelines has been further analyzed.

Biomechanical comparison of traditional anchors to all-suture anchors in a double-row rotator cuff repair cadaver model.

Science.gov (United States)

Goschka, Andrew M; Hafer, Jason S; Reynolds, Kirk A; Aberle, Nicholas S; Baldini, Todd H; Hawkins, Monica J; McCarty, Eric C

2015-10-01

To further reduce the invasiveness of arthroscopic rotator cuff repair surgery the all-suture anchor has been developed. The all-suture anchor requires less bone removal and reduces the potential of loose body complications. The all-suture anchor must also have adequate biomechanical strength for the repair to heal. The hypothesis is there is no significant difference in the biomechanical performance of supraspinatus repairs using an all-suture anchor when compared to traditional solid-body suture anchors. Using nine shoulders per group, the supraspinatus tendon was dissected from the greater tuberosity. The four different double row repairs tested were (medial row/lateral row): A: ICONIX2/ICONIX2; B: ICONIX2/Stryker ReelX 3.9mm; C: ICONIX2/Stryker ReelX 4.5mm; D: Arthrex BioComposite CorkScrew FT 4.5mm/Arthrex BioComposite SwiveLock 4.75mm. The ICONIX2 was the only all-suture anchor tested. Tendons underwent cyclic loading from 10 to 100N for 500 cycles, followed by load-to-failure. Data was collected at cycles 5, 100, 200, 300, 400, and 500. One-way ANOVA analysis was used to assess significance (P≤0.05). The anchor combinations tested did not differ significantly in anterior (P>0.4) or posterior (P>0.3) gap formation, construct stiffness (P>0.7), ultimate load (P=0.06), or load to 5mm gap formation (P=0.84). The all-suture anchor demonstrated comparable biomechanical performance in multiple double-row anchor combinations to a combination of traditional solid-body anchors. Thus it may be an attractive option to further reduce the invasiveness of rotator cuff repairs. Copyright © 2015 Elsevier Ltd. All rights reserved.

Constrained Active Learning for Anchor Link Prediction Across Multiple Heterogeneous Social Networks.

Science.gov (United States)

Zhu, Junxing; Zhang, Jiawei; Wu, Quanyuan; Jia, Yan; Zhou, Bin; Wei, Xiaokai; Yu, Philip S

2017-08-03

Nowadays, people are usually involved in multiple heterogeneous social networks simultaneously. Discovering the anchor links between the accounts owned by the same users across different social networks is crucial for many important inter-network applications, e.g., cross-network link transfer and cross-network recommendation. Many different supervised models have been proposed to predict anchor links so far, but they are effective only when the labeled anchor links are abundant. However, in real scenarios, such a requirement can hardly be met and most anchor links are unlabeled, since manually labeling the inter-network anchor links is quite costly and tedious. To overcome such a problem and utilize the numerous unlabeled anchor links in model building, in this paper, we introduce the active learning based anchor link prediction problem. Different from the traditional active learning problems, due to the one-to-one constraint on anchor links, if an unlabeled anchor link a = ( u , v ) is identified as positive (i.e., existing), all the other unlabeled anchor links incident to account u or account v will be negative (i.e., non-existing) automatically. Viewed in such a perspective, asking for the labels of potential positive anchor links in the unlabeled set will be rewarding in the active anchor link prediction problem. Various novel anchor link information gain measures are defined in this paper, based on which several constraint active anchor link prediction methods are introduced. Extensive experiments have been done on real-world social network datasets to compare the performance of these methods with state-of-art anchor link prediction methods. The experimental results show that the proposed Mean-entropy-based Constrained Active Learning (MC) method can outperform other methods with significant advantages.

Spin selection at organic spinterface by anchoring group

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhao; Qiu, Shuai; Miao, Yuan-yuan; Ren, Jun-feng; Wang, Chuan-kui [School of Physics and Electronics, Shandong Normal University, Jinan 250014 (China); Hu, Gui-chao, E-mail: hgc@sdnu.edu.cn [School of Physics and Electronics, Shandong Normal University, Jinan 250014 (China); Institute of Theoretical Physics, Technische Universität Dresden, 01062 Dresden (Germany)

2017-07-01

Highlights: • The sign of interfacial spin polarization can be selected by using different anchoring groups. • A sp{sup 3}-d or sp-d hybridization may occur and induce spin polarization when the anchoring group changes. • Interfacial spin polarization depends on both the type of the outer orbital of the anchoring atom as well as its energy. - Abstract: Control of organic interfacial spin polarization is crucial in organic spintronics. Based on ab initio theory, here we proposed a spin selection at organic interface via anchoring group by adsorbing an organic molecule onto Ni(111) surface. The results demonstrate that either a positive or negative interfacial spin polarization may be obtained by choosing different anchoring groups. The orbital analysis via the projected density of states shows that the interfacial spin polarization is sensitive to the hybridization of the outer orbital of the anchoring atom as well as its energy relative to the d orbital of the ferromagnetic atom. The work indicates a feasible way to realize spin selection at the organic spinterface by anchoring group.

Editorial Commentary: All-Suture Anchors, Foam Blocks, and Biomechanical Testing.

Science.gov (United States)

Brand, Jefferson C

2017-06-01

Barber's biomechanical work is well known to Arthroscopy's readers as thorough, comprehensive, and inclusive of new designs as they become available. In "All-Suture Anchors: Biomechanical Analysis of Pullout Strength, Displacement, and Failure Mode," the latest iteration, Barber and Herbert test all-suture anchors in both porcine femurs and biphasic foam. While we await in vivo clinical trials that compare all-suture anchors to currently used anchors, Barber and Herbert have provided data to inform anchor choice, and using their biomechanical data at time zero from all-suture anchor trials in an animal model, we can determine the anchors' feasibility for human clinical investigations. Copyright © 2017 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

Comparative Study on Different Slot Forms of Prestressed Anchor Blocks

Science.gov (United States)

Fan, Rong; Si, Jianhui; Jian, Zheng

2018-03-01

In this paper, two models of prestressed pier, rectangular cavity anchor block and arch hollow anchor block are established. The ABAQUS software was used to calculate the stress of the surface of the neck of the pier and the cavity of the anchor block, through comparative analysis. The results show that compared with the rectangular cavity anchor block, the stress of the pier and the cavity can be effectively reduced when the arch hole is used, and the amount of prestressed anchor can be reduced, so as to obtain obvious economic benefits.

Talar anchor placement for modified Brostrom lateral ankle stabilization procedure.

Science.gov (United States)

Angirasa, Arush K; Barrett, Michael J

2008-01-01

The modified Brostrom procedure has been a proven procedure with excellent utility in the treatment of lateral ankle instability within limitation. Multiple variations of the original technique have been described in the literature to date. Included in these variations are differences in anchor placement, suture technique, or both. In this research study, we propose placing a bone screw anchor into the lateral shoulder of the talus rather than the typical placement at the lateral malleolus for anatomic reconstruction of the lateral ankle ligaments.

Archaeometallurgical investigation of the iron anchor from the Tantura F shipwreck

Energy Technology Data Exchange (ETDEWEB)

Aronson, A. [Faculty of Engineering, Tel Aviv University, Ramat Aviv 69978 (Israel); Ashkenazi, D., E-mail: dana@eng.tau.ac.il [Faculty of Engineering, Tel Aviv University, Ramat Aviv 69978 (Israel); Barkai, O.; Kahanov, Y. [Leon Recanati Institute for Maritime Studies, University of Haifa, Haifa 31905 (Israel)

2013-04-15

The Tantura F shipwreck was a coaster or a fishing vessel about 15.7 m long, discovered in the Dor/Tantura lagoon, Israel in 1995. It was dated to between the mid-7th and the end of the 8th centuries CE. Among the finds excavated were two T-shaped type iron anchors. Of the two anchors, one (anchor A) was thoroughly studied by archaeometallurgical methods in order to identify forge-welding lines, to determine the welding quality and to understand the manufacturing technology. The examinations included X-ray radiography, XRF analysis, optical microscopy, SEM/EDS observation and analysis, OES analysis and microhardness tests. The investigation included characterization of the composition, microstructure, thermal treatments, forge-welding junctions and slag analysis. The results revealed a heterogeneous microstructure, rich in glassy, fayalite and wüstite slag. Iron based phases included ferrite, pearlite, cementite and Widmanstätten plates, all typical to wrought iron. The forge-welds of Anchor A were located. Each arm was made of one piece, weighing about 2.5–3 kg and the shank was made of a few 1.5–2 kg pieces. The second anchor (anchor B) was only briefly examined visually and with a few radiographs, which support the results from anchor A. The research results revealed significant information about T-shaped anchors and their manufacturing process, including hot-working processes without any additional heat treatments, and folding techniques. The microstructure was similar to other ancient simple tools such as saws, sickles, axes and mortise chisels, and though the technology to make complicated structures and objects, such as swords, existed at that time, the anchors did not require this sophistication; thus simpler techniques were used, presumably because they were more cost-effective. - Highlights: ► Tantura F was a coaster dated to mid-7th–end-8th centuries. ► Two iron anchors were discovered at the Tantura F shipwreck-site. ► Anchor A was

Conceptualization and Exploration of Composite Career Anchors: An Analysis of Information Systems Personnel.

Science.gov (United States)

Ramakrishna, Hindupur V.; Potosky, Denise

2003-01-01

Information systems professionals (n=163) completed measures of career anchors and outcomes (career/job satisfaction, job performance, perceived advancement prospects); 46% had multiple dominant anchors and these individuals did not have significantly different career outcomes than those with single dominant anchors. (Contains 26 references.) (SK)

Biomechanical Analysis of Suture Anchor vs Tenodesis Screw for FHL Transfer.

Science.gov (United States)

Drakos, Mark C; Gott, Michael; Karnovsky, Sydney C; Murphy, Conor I; DeSandis, Bridget A; Chinitz, Noah; Grande, Daniel; Chahine, Nadeen

2017-07-01

Chronic Achilles injury is often treated with flexor hallucis longus (FHL) tendon transfer to the calcaneus using 1 or 2 incisions. A single incision avoids the risks of extended dissections yet yields smaller grafts, which may limit fixation options. We investigated the required length of FHL autograft and biomechanical profiles for suture anchor and biotenodesis screw fixation. Single-incision FHL transfer with suture anchor or biotenodesis screw fixation to the calcaneus was performed on 20 fresh cadaveric specimens. Specimens were cyclically loaded until maximal load to failure. Length of FHL tendon harvest, ultimate load, stiffness, and mode of failure were recorded. Tendon harvest length needed for suture anchor fixation was 16.8 ± 2.1 mm vs 29.6 ± 2.4 mm for biotenodesis screw ( P = .002). Ultimate load to failure was not significantly different between groups. A significant inverse correlation existed between failure load and donor age when all specimens were pooled (ρ = -0.49, P Anchor failure occurred mostly by suture breakage (n = 8). Adequate FHL tendon length could be harvested through a single posterior incision for fixation to the calcaneus with either fixation option, but suture anchor required significantly less graft length. Stiffness, fixation strength, and load to failure were comparable between groups. An inverse correlation existed between failure load and donor age. Younger specimens with screw fixation demonstrated significantly greater failure loads. Adequate harvest length for FHL transfer could be achieved with a single posterior incision. There was no difference in strength of fixation between suture anchor and biotenodesis screw.

Analysis of anchor bolt belongs to fan in nuclear power plant

International Nuclear Information System (INIS)

Miao Xueliang; Luan Xingfeng; Zhang Wei; Bian Chunhua; Yu Xiaoyan; Xu Ke; Liu Hongqun

2014-01-01

Through on the fan anchor bolt material components, metallurgical structure and fracture analysis indicates that: material composition and microscopic are abnormal, it led to material brittle increased, the fracture is rock-candy structure, the last part is toughness structure. The reason is the the fan vibrate oversize. At last, we put forward some measures. Just like, control the vibration of the fan, set a nominal tightening torque when installing bolt. (authors)

Installation of concrete expansion anchors at the Fast Flux Test Facility

International Nuclear Information System (INIS)

Clark, G.L.

1980-01-01

Installation criteria utilized at the Fast Flux Test Facility for concrete expansion anchors are presented. Static and dynamic load capabilities of various anchor types are discussed in relation to design loads, with particular emphasis placed on the yield load (the proportional limit). Effects of several variables (i.e., installation torque, hole diameter) are also investigated. Resolution and documentation of field problems (e.g., improper spacing, embedment, angularity) are also described. Recommendations for improving and controlling future installations are given

Anchor Bolt Position in Base Plate In Terms Of T and J Anchor Bolt

Directory of Open Access Journals (Sweden)

b Osman Mohamad Hairi

2017-01-01

Full Text Available Generally, L anchor bolt system has been used for a long period of time in construction industry as one of the distributing load structures. However, there are some weaknesses in L anchor bolt which may straighten and pullup when charged with tensile load. Current practices prefer to use other types of anchor bolt systems, such as headed studs anchor bolt system to replace the L anchor bolt design. There has been lack of studies to prove that it is more effective in terms of performance. A new T anchor bolt which was basically modified from headed studs anchor bolt was proposed in this study to compare its performance of tensile loading in concrete failure to typical L design. This study aims to determine whether the T anchor bolt system gives better performance as compared to an L anchor bolt system. The performance was rated based on tensile loading on concrete failure pattern. A pullout test was conducted on two different anchor bolt systems, namely L and T. The anchor bolt embedded depth, h in concrete were varied according to their hook or bend radius. Each sample was repeated twice. There were totally eight samples. The hook or bend radius used were 50 mm and 57.5 mm for sample L1 and L2, respectively. 90-degree bend were used on sample T1 and T2. Based on test results, it can be seen that the performance of concrete failure pattern under tensile load on both L and T anchor bolt design samples with 200 mm embedment depth was better than deeper embedment depth of 230 mm. But the L anchor bolt design gives the best results as compared to T design. Although T anchor bolt design shows higher resistance before first bond failure to the concrete sample. T anchor bolt was analysed and needed deeper embedment depth to allow formation of cone pull-out shape to acquire better performance.

The Model of Career Anchors as a Tool in the Analysis of Instructional Developers.

Science.gov (United States)

Miller, Carol

1981-01-01

Examines the importance of human systems as a relevant aspect of development processes and looks at the career anchor model proposed by Schein as a possible area in the analysis of the instructional developer/client relationships. Fourteen references are listed. (Author/LLS)

Mutational analysis of the glycosylphosphatidylinositol (GPI) anchor pathway demonstrates that GPI-anchored proteins are required for cell wall biogenesis and normal hyphal growth in Neurospora crassa.

Science.gov (United States)

Bowman, Shaun M; Piwowar, Amy; Al Dabbous, Mash'el; Vierula, John; Free, Stephen J

2006-03-01

Using mutational and proteomic approaches, we have demonstrated the importance of the glycosylphosphatidylinositol (GPI) anchor pathway for cell wall synthesis and integrity and for the overall morphology of the filamentous fungus Neurospora crassa. Mutants affected in the gpig-1, gpip-1, gpip-2, gpip-3, and gpit-1 genes, which encode components of the N. crassa GPI anchor biosynthetic pathway, have been characterized. GPI anchor mutants exhibit colonial morphologies, significantly reduced rates of growth, altered hyphal growth patterns, considerable cellular lysis, and an abnormal "cell-within-a-cell" phenotype. The mutants are deficient in the production of GPI-anchored proteins, verifying the requirement of each altered gene for the process of GPI-anchoring. The mutant cell walls are abnormally weak, contain reduced amounts of protein, and have an altered carbohydrate composition. The mutant cell walls lack a number of GPI-anchored proteins, putatively involved in cell wall biogenesis and remodeling. From these studies, we conclude that the GPI anchor pathway is critical for proper cell wall structure and function in N. crassa.

Effectiveness of TAD-anchored maxillary protraction in late mixed dentition.

Science.gov (United States)

Feng, Xiaoxia; Li, Jianhua; Li, Yu; Zhao, Zhihe; Zhao, Sen; Wang, Jue

2012-11-01

To evaluate the effectiveness of temporary anchorage device (TAD)-anchored maxillary protraction (MP) in terms of the skeletal and dentoalveolar changes and to compare it with traditional tooth-anchored MP. A computerized literature search for relative randomized controlled trials and prospective controlled trials was performed in PubMed, MEDLINE, Cochrane Central Register of Controlled Trials, Embase, CNKI, and Google Scholar, complemented with manual search. Data extraction and quality assessment were carried out by two reviewers independently. Meta-analysis was followed when possible; otherwise, description was done. Forty articles were found, among which four trials were qualified for meta-analysis. The results showed that there was significant difference between TAD-anchored MP and untreated control in terms of maxillary advancement (weighted mean differences (WMD) 3.08 mm; 95% CI: 1.61 to approximately 4.56; P TAD-anchored MP might have a greater maxillary advancement effect and might reduce skeletal and dental side effects, compared with tooth-anchored MP.

Simplified design of flexible expansion anchored plates for nuclear structures

International Nuclear Information System (INIS)

Mehta, N.K.; Hingorani, N.V.; Longlais, T.G.; Sargent and Lundy, Chicago, IL)

1984-01-01

In nuclear power plant construction, expansion anchored plates are used to support pipe, cable tray and HVAC duct hangers, and various structural elements. The expansion anchored plates provide flexibility in the installation of field-routed lines where cast-in-place embedments are not available. General design requirements for expansion anchored plate assemblies are given in ACI 349, Appendix B (1). The manufacturers recommend installation procedures for their products. Recent field testing in response to NRC Bulletin 79-02 (2) indicates that anchors, installed in accordance with manufacturer's recommended procedures, perform satisfactorily under static and dynamic loading conditions. Finite element analysis is a useful tool to correctly analyze the expansion anchored plates subject to axial tension and biaxial moments, but it becomes expensive and time-consuming to apply this tool for a large number of plates. It is, therefore, advantageous to use a simplified method, even though it may be more conservative as compared to the exact method of analysis. This paper presents a design method referred to as the modified rigid plate analysis approach to simplify both the initial design and the review of as-built conditions

Understanding the low uptake of bone-anchored hearing aids: a review.

Science.gov (United States)

Powell, R; Wearden, A; Pardesi, S M; Green, K

2017-03-01

Bone-anchored hearing aids improve hearing for patients for whom conventional behind-the-ear aids are problematic. However, uptake of bone-anchored hearing aids is low and it is important to understand why this is the case. A narrative review was conducted. Studies examining why people accept or decline bone-anchored hearing aids and satisfaction levels of people with bone-anchored hearing aids were reviewed. Reasons for declining bone-anchored hearing aids included limited perceived benefits, concerns about surgery, aesthetic concerns and treatment cost. No studies providing in-depth analysis of the reasons for declining or accepting bone-anchored hearing aids were identified. Studies of patient satisfaction showed that most participants reported benefits with bone-anchored hearing aids. However, most studies used cross-sectional and/or retrospective designs and only included people with bone-anchored hearing aids. Important avenues for further research are in-depth qualitative research designed to fully understand the decision-making process for bone-anchored hearing aids and rigorous quantitative research comparing satisfaction of people who receive bone-anchored hearing aids with those who receive alternative (or no) treatments.

Design Analysis and Observed Performance of a Tieback Anchored Pile Wall in Sand

Directory of Open Access Journals (Sweden)

Jian-Yong Han

2017-01-01

Full Text Available This paper aims to study the design process and service performance of a deep excavation supported by tieback anchored pile walls. The design procedure and design approaches for deep excavation in China are described. Based on the excavation case history for Shenyang, China, design results obtained using the elastic method and the finite element method (FEM are compared and analyzed. Special emphasis is given to the analysis of horizontal wall deformations, internal forces in the wall, earth pressures on the wall, ground surface settlements, and stabilities of the excavation. The similarities and differences between the Chinese code (JGJ 120-2012 and the European code (EN 1997-1 for the design of geotechnical structures are presented based on a design example. Through the comparison, it is indicated that the Chinese code focuses on the design result, while the European code focuses on the design process. The crucial construction methods for reducing construction risk based on the excavation case history are described. The mechanical behaviors of the excavation retained by an anchored pile wall were investigated by analyzing observed field cases. The results provide good, practical guidelines for the design and construction of a tieback anchored pile wall retained excavation in sandy soil.

Anchors as Semantic Primes in Value Construction: An EEG Study of the Anchoring Effect.

Directory of Open Access Journals (Sweden)

Qingguo Ma

Full Text Available Previous research regarding anchoring effects has demonstrated that human judgments are often assimilated to irrelevant information. Studies have demonstrated that anchors influence the economic valuation of various products and experiences; however, the cognitive explanations of this effect remain controversial, and its neural mechanisms have rarely been explored. In the current study, we conducted an electroencephalography (EEG experiment to investigate the anchoring effect on willingness to accept (WTA for an aversive hedonic experience and the role of anchors in this judgment heuristic. The behavioral results demonstrated that random numbers affect participants' WTA for listening to pieces of noise. The participants asked for higher pay after comparing their WTA with higher numbers. The EEG results indicated that anchors also influenced the neural underpinnings of the valuation process. Specifically, when a higher anchor number was drawn, larger P2 and late positive potential amplitudes were elicited, reflecting the anticipation of more intensive pain from the subsequent noise. Moreover, higher anchors induced a stronger theta band power increase compared with lower anchors when subjects listened to the noises, indicating that the participants felt more unpleasant during the actual experience of the noise. The levels of unpleasantness during both anticipation and experience were consistent with the semantic information implied by the anchors. Therefore, these data suggest that a semantic priming process underlies the anchoring effect in WTA. This study provides proof for the robustness of the anchoring effect and neural evidence of the semantic priming model. Our findings indicate that activated contextual information, even seemingly irrelevant, can be embedded in the construction of economic value in the brain.

Career anchors and learning plan (part one

Directory of Open Access Journals (Sweden)

Daniela Brečko

2006-12-01

Full Text Available The article is divided into three parts. The first part concentrates on how important career is for an individual, organization and society. The author establishes that understanding of career has changed dramatically and does not only refer to climbing up the career ladder, but also moving off or even down the career ladder. The notion of career, as a lifelong and professional path, encompasses all aspects of human personality and their roles acquired through one's life. On basis of vast and longitudinal research, where the author has studied career anchors of individuals, it is the objective of the author to find out on basis of what grounds do the individuals decide to take certain directions in their careers and how learning contributes to such decisions. As a source the author has used Shein's theory of career anchors. Part one describes in greater detail 8 different career anchors and introduces their main features with the findings of the research, which refer to the analysis of professions (work positions and established career anchors. The author thus verifies the hypothesis that career anchors do exist in our area.

The anchoring bias reflects rational use of cognitive resources.

Science.gov (United States)

Lieder, Falk; Griffiths, Thomas L; M Huys, Quentin J; Goodman, Noah D

2018-02-01

Cognitive biases, such as the anchoring bias, pose a serious challenge to rational accounts of human cognition. We investigate whether rational theories can meet this challenge by taking into account the mind's bounded cognitive resources. We asked what reasoning under uncertainty would look like if people made rational use of their finite time and limited cognitive resources. To answer this question, we applied a mathematical theory of bounded rationality to the problem of numerical estimation. Our analysis led to a rational process model that can be interpreted in terms of anchoring-and-adjustment. This model provided a unifying explanation for ten anchoring phenomena including the differential effect of accuracy motivation on the bias towards provided versus self-generated anchors. Our results illustrate the potential of resource-rational analysis to provide formal theories that can unify a wide range of empirical results and reconcile the impressive capacities of the human mind with its apparently irrational cognitive biases.

INAA, AAS, and lead isotope analysis of ancient lead anchors from the black SEA

International Nuclear Information System (INIS)

Kuleff, I.; Djingova, R.; Alexandrova, A.

1995-01-01

Lead stock of wooden-lead anchors found along the Bulgarian Black Sea coast and typo logically dated VI c. B.C. - III c. A.D. have been analyzed for chemical composition and lead isotope ratios by INAA, AAS and mass spectrometry. Using multivariate methods for analysis as well as simple bi variate plots the lead for production of the stocks was localized as originating from Laurion, Thassos, Troas, Chalkidike and the Rhodopes. In general, the chemical composition is not recommended to be used for provenance study of lead artefacts. Combining the results from this study with the existing typo logical classification certain conclusion about the production and distribution of lead anchors in the Aegean region are made. (author). 22 refs., 3 figs., 4 tabs

Susceptibility to anchoring effects

Directory of Open Access Journals (Sweden)

Todd McElroy

2007-02-01

Full Text Available Previous research on anchoring has shown this heuristic to be a very robust psychological phenomenon ubiquitous across many domains of human judgment and decision-making. Despite the prevalence of anchoring effects, researchers have only recently begun to investigate the underlying factors responsible for how and in what ways a person is susceptible to them. This paper examines how one such factor, the Big-Five personality trait of openness-to-experience, influences the effect of previously presented anchors on participants' judgments. Our findings indicate that participants high in openness-to-experience were significantly more influenced by anchoring cues relative to participants low in this trait. These findings were consistent across two different types of anchoring tasks providing convergent evidence for our hypothesis.

Comparison of Suture-Based Anchors and Traditional Bioabsorbable Anchors in Foot and Ankle Surgery.

Science.gov (United States)

Hembree, W Chad; Tsai, Michael A; Parks, Brent G; Miller, Stuart D

We compared the pullout strength of a suture-based anchor versus a bioabsorbable anchor in the distal fibula and calcaneus and evaluated the relationship between bone mineral density and peak load to failure. Eight paired cadaveric specimens underwent a modified Broström procedure and Achilles tendon reattachment. The fibula and calcaneus in the paired specimens received either a suture-based anchor or a bioabsorbable suture anchor. The fibular and calcaneal specimens were loaded to failure, defined as a substantial decrease in the applied load or pullout from the bone. In the fibula, the peak load to failure was significantly greater with the suture-based versus the bioabsorbable anchors (133.3 ± 41.8 N versus 76.8 ± 35.3 N; p = .002). No significant difference in load with 5 mm of displacement was found between the 2 groups. In the calcaneus, no difference in the peak load to failure was found between the 2 groups, and the peak load to failure with 5 mm of displacement was significantly lower with the suture-based than with the bioabsorbable anchors (52.2 ± 9.8 N versus 75.9 ± 12.4 N; p = .003). Bone mineral density and peak load to failure were significantly correlated in the fibula with the suture-based anchor. An innovative suture-based anchor had a greater peak load to failure compared with a bioabsorbable anchor in the fibula. In the calcaneus, the load at 5 mm of displacement was significantly lower in the suture-based than in the bioabsorbable group. The correlation findings might indicate the need for a cortical bone shelf with the suture-based anchor. Suture-based anchors could be a viable alternative to bioabsorbable anchors for certain foot and ankle procedures. Copyright © 2016 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

Numerical Simulation of Electro-Mechanical Impedance Response in Cable-Anchor Connection Interface

International Nuclear Information System (INIS)

Nguyen, Khac Duy; Kim, Jeong Tae

2011-01-01

In this study, a finite element(FE) analysis on electro-mechanical impedance response of cable-anchor connection interface under various anchor force is presented. In order to achieve the objective, the following approaches are implemented. Firstly, an interface washer coupled with piezoelectric(PZT) material is designed for monitoring cable-force loss. The interface washer is a small aluminum plate on which a PZT patch is surface-bonded. Cable-force loss could be monitored by installing the interface washer between the anchor plate and the anchorage of cable-anchor connection and examining the changes of impedance of the interface washer. Secondly, a FE model for cable-anchor connection is established to examine the effect of cable-force on impedance response of interface washer. Also, the effects of geometrical and material properties of the interface washer on impedance responses under various cable-forces are investigated. Finally, validation of the FE analysis is experimentally evaluated by a lab-scale cable-anchor connection

Analysis of AISI 304 Tensile Strength as an Anchor Chain of Mooring System

Science.gov (United States)

Hamidah, I.; Wati, R.; Hamdani, R. A.

2018-05-01

The background of this research is the use of mild steel (i.e., St37) as anchor chain that works on the corrosive environment of seawater which is possible to decrease its tensile strength. The longer soaked in seawater, the more significant the lowering of its tensile strength. Anchor chain needs to be designed by considering its tensile strength and corrosion resistance, so it’s able to support mooring system well. The primary purpose of this research is obtaining the decreasing of stainless steel 304 (AISI 304) tensile strength which is corroded by seawater as anchor chain of the mooring system. It is also essential to obtain the lifetime of AISI304 and St37 as anchor chain with the same load, the corrosion rate of AISI 304, and St 37 in seawater. The method which was employed in this research is an experiment with four pieces of stainless steel AISI 304, and of St 37 corrosion testing samples, six pieces of stainless steel 304, and six pieces of St 37 for tensile testing samples. The result of this research shows that seawater caused stainless steel AISI 304 as anchor chain has decreased of tensile strength about 1.68 % during four weeks. Also, it indicates that AISI 304 as anchor chain has a lifetime about 130 times longer than St 37. Further, we found that the corrosion rate of stainless steel 304 in seawater is 0.2042 mpy in outstanding category, while the St 37 samples reached up to 27.0247 mpy ranked as fair category. This result recommends that AISI 304 more excellence than St 37 as anchor chain of the mooring system.

Geometric nonlinear analysis of self-anchored cable-stayed suspension bridges.

Science.gov (United States)

Hui-Li, Wang; Yan-Bin, Tan; Si-Feng, Qin; Zhe, Zhang

2013-01-01

Geometric nonlinearity of self-anchored cable-stayed suspension bridges is studied in this paper. The repercussion of shrinkage and creep of concrete, rise-to-span ratio, and girder camber on the system is discussed. A self-anchored cable-stayed suspension bridge with a main span of 800 m is analyzed with linear theory, second-order theory, and nonlinear theory, respectively. In the condition of various rise-to-span ratios and girder cambers, the moments and displacements of both the girder and the pylon under live load are acquired. Based on the results it is derived that the second-order theory can be adopted to analyze a self-anchored cable-stayed suspension bridge with a main span of 800 m, and the error is less than 6%. The shrinkage and creep of concrete impose a conspicuous impact on the structure. And it outmatches suspension bridges for system stiffness. As the rise-to-span ratio increases, the axial forces of the main cable and the girder decline. The system stiffness rises with the girder camber being employed.

Geometric Nonlinear Analysis of Self-Anchored Cable-Stayed Suspension Bridges

Directory of Open Access Journals (Sweden)

Wang Hui-Li

2013-01-01

Full Text Available Geometric nonlinearity of self-anchored cable-stayed suspension bridges is studied in this paper. The repercussion of shrinkage and creep of concrete, rise-to-span ratio, and girder camber on the system is discussed. A self-anchored cable-stayed suspension bridge with a main span of 800 m is analyzed with linear theory, second-order theory, and nonlinear theory, respectively. In the condition of various rise-to-span ratios and girder cambers, the moments and displacements of both the girder and the pylon under live load are acquired. Based on the results it is derived that the second-order theory can be adopted to analyze a self-anchored cable-stayed suspension bridge with a main span of 800 m, and the error is less than 6%. The shrinkage and creep of concrete impose a conspicuous impact on the structure. And it outmatches suspension bridges for system stiffness. As the rise-to-span ratio increases, the axial forces of the main cable and the girder decline. The system stiffness rises with the girder camber being employed.

Experimental Research on Destruction Mode and Anchoring Performance of Carbon Fiber Phyllostachys pubescens Anchor Rod with Different Forms

Directory of Open Access Journals (Sweden)

Wang Yulan

2018-01-01

Full Text Available The anchoring technology is extensively applied in reinforcing protection of the earth relics. Now that no specification is available for different new anchor rods in earth relics protection due to diversified destruction modes of earth relics and complexity of engineering technology conditions, it is urgent to guide reinforcing design and construction with a complete detailed anchor rod research document. With the new carbon fiber Phyllostachys pubescens anchor rod as the research object, six lots of in situ tests are designed to, respectively, study the destruction mode and anchoring performance of the carbon fiber Phyllostachys pubescens anchor rod under different anchor length L, anchor rod diameter D, bore diameter H, grouting material S, rib spacing R, and inclination angle A in this paper. By studying load shift curve experiment in drawing of the anchor rod, the destruction mode and ultimate bearing capacity of the carbon fiber Phyllostachys pubescens anchor rod in different experiment lots are obtained, and the concept of permitted application value N in anchor rod design is proposed. By studying strain distribution characteristics of anchor rods in experimental lots along the length direction under action of the permitted application value N and combining the existing destruction mode and ultimate bearing capacity, this paper analyzes influences of L, D, H, S, R, and A on anchoring effect of the carbon fiber Phyllostachys pubescens anchor rod; gives the reasonable value range of L, D, H, and R when the carbon fiber Phyllostachys pubescens anchor rod is used for reinforcing design of the earth relics; and provides favorable experiment basis for reinforcing design of the earth relics based on the carbon fiber Phyllostachys pubescens anchor rod.

Experimental testing of anchoring devices for bottom rails in partially anchored timber frame shear walls

OpenAIRE

Caprolu, Giuseppe

2011-01-01

Källsner and Girhammar have presented a new plastic design method of wood-framed shear walls at ultimate limit state. This method allows the designer to calculate the load-carrying capacity of shear walls partially anchored, where the leading stud is not anchored against the uplift.The anchorage system of shear walls is provided from anchor bolts and hold downs. Anchor bolts provide horizontal shear continuity between the bottom rail and the foundation. Hold downs are directly connected from ...

Surface analysis of PEGylated nano-shields on nanoparticles installed by hydrophobic anchors

DEFF Research Database (Denmark)

Ebbesen, M F; Whitehead, Bradley Joseph; Gonzalez, Borja Ballarin

2013-01-01

and cellular interactions. Methods: Poly(lactic-co-glycolic acid) (PLGA) nanoparticles were prepared with a hydrophilic PEGylated "nano-shield" inserted at different levels by hydrophobic anchoring using either a phospholipid-PEG conjugate or the copolymer PLGA-block-PEG by an emulsification/diffusion method....... Surface and bulk analysis was performed including X-ray photoelectron spectroscopy (XPS), nuclear magnetic resonance spectroscopy (NMR) and zeta potential. Cellular uptake was investigated in RAW 264.7 macrophages by flow cytometry. Results: Sub-micron nanoparticles were formed and the combination of (NMR...

GPI-anchored protein organization and dynamics at the cell surface.

Science.gov (United States)

Saha, Suvrajit; Anilkumar, Anupama Ambika; Mayor, Satyajit

2016-02-01

The surface of eukaryotic cells is a multi-component fluid bilayer in which glycosylphosphatidylinositol (GPI)-anchored proteins are an abundant constituent. In this review, we discuss the complex nature of the organization and dynamics of GPI-anchored proteins at multiple spatial and temporal scales. Different biophysical techniques have been utilized for understanding this organization, including fluorescence correlation spectroscopy, fluorescence recovery after photobleaching, single particle tracking, and a number of super resolution methods. Major insights into the organization and dynamics have also come from exploring the short-range interactions of GPI-anchored proteins by fluorescence (or Förster) resonance energy transfer microscopy. Based on the nanometer to micron scale organization, at the microsecond to the second time scale dynamics, a picture of the membrane bilayer emerges where the lipid bilayer appears inextricably intertwined with the underlying dynamic cytoskeleton. These observations have prompted a revision of the current models of plasma membrane organization, and suggest an active actin-membrane composite. Copyright © 2016 by the American Society for Biochemistry and Molecular Biology, Inc.

Not all Anchors Weigh Equally.

Science.gov (United States)

Greenstein, Michael; Velazquez, Alexandra

2017-11-01

The anchoring bias is a reliable effect wherein a person's judgments are affected by initially presented information, but it is unknown specifically why this effect occurs. Research examining this bias suggests that elements of both numeric and semantic priming may be involved. To examine this, the present research used a phenomenon wherein people treat numeric information presented differently in Arabic numeral or verbal formats. We presented participants with one of many forms of an anchor that represented the same value (e.g., twelve hundred or 1,200). Thus, we could examine how a concept's meaning and its absolute numeric value affect anchoring. Experiments 1 and 2 showed that people respond to Arabic and verbal anchors differently. Experiment 3 showed that these differences occurred largely because people tend to think of numbers in digit format. This suggests that one's conceptual understanding of the anchored information matters more than its strict numeric value.

Bulk chirality effect for symmetric bistable switching of liquid crystals on topologically self-patterned degenerate anchoring surface.

Science.gov (United States)

Park, Min-Kyu; Joo, Kyung-Il; Kim, Hak-Rin

2017-06-26

We demonstrate a bistable switching liquid crystal (LC) mode utilizing a topologically self-structured dual-groove surface for degenerated easy axes of LC anchoring. In our study, the effect of the bulk elastic distortion of the LC directors on the bistable anchoring surface is theoretically analyzed for balanced bistable states based on a free energy diagram. By adjusting bulk LC chirality, we developed ideally symmetric and stable bistable anchoring and switching properties, which can be driven by a low in-plane pulsed field of about 0.7 V/µm. The fabricated device has a contrast ratio of 196:1.

Model Solutions for Performance-Based Seismic Analysis of an Anchored Sheet Pile Quay Wall

OpenAIRE

C. J. W. Habets; D. J. Peters; J. G. de Gijt; A. V. Metrikine; S. N. Jonkman

2016-01-01

Conventional seismic designs of quay walls in ports are mostly based on pseudo-static analysis. A more advanced alternative is the Performance-Based Design (PBD) method, which evaluates permanent deformations and amounts of (repairable) damage under seismic loading. The aim of this study is to investigate the suitability of this method for anchored sheet pile quay walls that were not purposely designed for seismic loads. A research methodology is developed in which pseudo-static, permanent-di...

Microgravity Drill and Anchor System

Science.gov (United States)

Parness, Aaron; Frost, Matthew A.; King, Jonathan P.

2013-01-01

This work is a method to drill into a rock surface regardless of the gravitational field or orientation. The required weight-on-bit (WOB) is supplied by a self-contained anchoring mechanism. The system includes a rotary percussive coring drill, forming a complete sampling instrument usable by robot or human. This method of in situ sample acquisition using micro - spine anchoring technology enables several NASA mission concepts not currently possible with existing technology, including sampling from consolidated rock on asteroids, providing a bolt network for astronauts visiting a near-Earth asteroid, and sampling from the ceilings or vertical walls of lava tubes and cliff faces on Mars. One of the most fundamental parameters of drilling is the WOB; essentially, the load applied to the bit that allows it to cut, creating a reaction force normal to the surface. In every drilling application, there is a minimum WOB that must be maintained for the system to function properly. In microgravity (asteroids and comets), even a small WOB could not be supported conventionally by the weight of the robot or astronaut. An anchoring mechanism would be needed to resist the reactions, or the robot or astronaut would push themselves off the surface and into space. The ability of the system to anchor itself to a surface creates potential applications that reach beyond use in low gravity. The use of these anchoring mechanisms as end effectors on climbing robots has the potential of vastly expanding the scope of what is considered accessible terrain. Further, because the drill is supported by its own anchor rather than by a robotic arm, the workspace is not constrained by the reach of such an arm. Yet, if the drill is on a robotic arm, it has the benefit of not reflecting the forces of drilling back to the arm s joints. Combining the drill with the anchoring feet will create a highly mobile, highly stable, and highly reliable system. The drilling system s anchor uses hundreds of

Mechanical Characteristics Analysis of Surrounding Rock on Anchor Bar Reinforcement

Science.gov (United States)

Gu, Shuan-cheng; Zhou, Pan; Huang, Rong-bin

2018-03-01

Through the homogenization method, the composite of rock and anchor bar is considered as the equivalent material of continuous, homogeneous, isotropic and strength parameter enhancement, which is defined as reinforcement body. On the basis of elasticity, the composite and the reinforcement are analyzed, Based on strengthening theory of surrounding rock and displacement equivalent conditions, the expression of reinforcement body strength parameters and mechanical parameters is deduced. The example calculation shows that the theoretical results are close to the results of the Jia-mei Gao[9], however, closer to the results of FLAC3D numerical simulation, it is proved that the model and surrounding rock reinforcement body theory are reasonable. the model is easy to analyze and calculate, provides a new way for determining reasonable bolt support parameters, can also provides reference for the stability analysis of underground cavern bolting support.

The Holding Power of Anchors

Indian Academy of Sciences (India)

The efficiency of an anchor may be expressed as the ratio (holding force + weight of anchor). In dry sand .... the market at the beginning of the coming season in three sizes, namely 20, 35 and. 60 lb. These are ... Taylor frozen-flow hypothesis.

Extracellular glycosylphosphatidylinositol-anchored mannoproteins and proteases of Cryptococcus neoformans.

Science.gov (United States)

Eigenheer, Richard A; Jin Lee, Young; Blumwald, Eduardo; Phinney, Brett S; Gelli, Angie

2007-06-01

Extracellular proteins of Cryptococcus neoformans are involved in the pathogenesis of cryptococcosis, and some are immunoreactive antigens that may potentially serve as candidates for vaccine development. To further study the extracellular proteome of the human fungal pathogen Cry. neoformans, we conducted a proteomic analysis of secreted and cell wall-bound proteins with an acapsular strain of Cry. neoformans. Proteins were identified from both intact cells and cell walls. In both cases, extracellular proteins were removed with trypsin or beta-glucanase, and then all proteins/peptides were purified by solid-phase extraction, spin dialysis, and HPLC, and identified by liquid chromatography-mass spectrometry. This study identified 29 extracellular proteins with a predicted N-terminal signal sequence and also a predicted glycosylphosphatidylinositol anchor motif in more than half. Among the novel proteins identified were five glycosylphosphatidylinositol-anchored proteins with extensive Ser/Thr-rich regions but no apparent functional domains, a glycosylphosphatidylinositol-anchored aspartic protease, and a metalloprotease with structural similarity to an elastinolytic metalloprotease of Aspergillus fumigatus. This study suggests that Cry. neoformans has the machinery required to target glycosylphosphatidylinositol-anchored proteins to the cell wall, and it confirms the extracellular proteolytic ability of Cry. neoformans.

Analysis of timber and coating material on an iron anchor recovered off Aguada Bay, Goa

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.; Rao, B.R.; Shashikala, S.; Rao, R.V.; Khedekar, V.D.

Shanked iron anchor measuring 3.30 m long with a 4.37 m wooden stock was recovered off Aguada Bay, Goa at a water depth of 11 m. The anchor has been tentatively dated contemporary with the maritime history of Goa and Portugal between the 16th and 17th...

Anchoring effects on early autobiographical memories.

Science.gov (United States)

Greenberg, Daniel L; Bishara, Anthony J; Mugayar-Baldocchi, Marino A

2017-10-01

Studies of childhood memory typically show that our earliest memories come from between three and four years of age. This finding is not universal, however. The age estimate varies across cultures and is affected by social influences. Research from the judgments and decision-making literature suggests that these estimates might also involve a judgment under uncertainty. Therefore, they might be susceptible to less social influences such as heuristics and biases. To investigate this possibility, we conducted two experiments that used anchoring paradigms to influence participants' estimates of their age during early autobiographical memories. In Experiment 1, participants answered either a high-anchor or a low-anchor question, and were warned that the anchor was uninformative; they went on to estimate their age during their earliest autobiographical memory. In Experiment 2, we replicated Experiment 1 and extended the design to examine additional early autobiographical memories. In both experiments, participants in the low-anchor condition gave earlier age estimates than those in the high-anchor condition. These results provide new insights into the methods used to investigate autobiographical memory. Moreover, they show that reports of early autobiographical memories can be influenced by a relatively light touch - a change to a single digit in a single question.

An earth anchor system: installation and design guide.

Science.gov (United States)

R.L. Copstead; D.D. Studier

1990-01-01

A system for anchoring the guylines and skylines of cable yarding equipment is presented. A description of three types of tipping plate anchors is given. Descriptions of the installation equipment and methods specific to each type are given. Procedures for determining the correct number of anchors to install are included, as are guidelines for installing the anchors so...

Stability calculation method of slope reinforced by prestressed anchor in process of excavation.

Science.gov (United States)

Li, Zhong; Wei, Jia; Yang, Jun

2014-01-01

This paper takes the effect of supporting structure and anchor on the slope stability of the excavation process into consideration; the stability calculation model is presented for the slope reinforced by prestressed anchor and grillage beam, and the dynamic search model of the critical slip surface also is put forward. The calculation model of the optimal stability solution of each anchor tension of the whole process is also given out, through which the real-time analysis and checking of slope stability in the process of excavation can be realized. The calculation examples indicate that the slope stability is changed with the dynamic change of the design parameters of anchor and grillage beam. So it is relatively more accurate and reasonable by using dynamic search model to determine the critical slip surface of the slope reinforced by prestressed anchor and grillage beam. Through the relationships of each anchor layout and the slope height of various stages of excavation, and the optimal stability solution of prestressed bolt tension design value in various excavation stages can be obtained. The arrangement of its prestressed anchor force reflects that the layout of the lower part of bolt and the calculation of slope reinforcement is in line with the actual. These indicate that the method is reasonable and practical.

Improving performance by anchoring movement and "nerves".

Science.gov (United States)

Iso-Ahola, Seppo E; Dotson, Charles O; Jagodinsky, Adam E; Clark, Lily C; Smallwood, Lorraine L; Wilburn, Christopher; Weimar, Wendi H; Miller, Matthew W

2016-10-01

Golf's governing bodies' recent decision to ban all putting styles "anchoring one end of the club against the body" bridges an important practical problem with psychological theory. We report the first experiment testing whether anchoring provides technical and/or psychological advantage in competitive performance. Many "greats" of professional golf from Arnold Palmer and Jack Nicklaus to Tiger Woods have argued against anchoring, believing that it takes "nerves" out of competitive performance and therefore artificially levels the playing field. To shed more light on the issue, we tested participants' performance with anchored and unanchored putters under low and high pressure when controlling for the putter length. We found no statistically significant evidence for a technical advantage due to anchoring but a clear psychological advantage: participants who anchored their putters significantly outperformed unanchored counterparts under high, but not low, pressure. Results provide tentative evidence for the ban's justification from a competitive standpoint. However, before any definite conclusions can be made, more research is needed when using high-level golfers. Copyright © 2016 Elsevier B.V. All rights reserved.

Enhancement of Orthodontic Anchor Screw Stability Under Immediate Loading by Ultraviolet Photofunctionalization Technology.

Science.gov (United States)

Takahashi, Maiko; Motoyoshi, Mitsuru; Inaba, Mizuki; Hagiwara, Yoshiyuki; Shimizu, Noriyoshi

Ultraviolet (UV)-mediated photofunctionalization technology is intended to enhance the osseointegration capability of titanium implants. There are concerns about orthodontic anchor screws loosening under immediate loading protocols in adolescent orthodontic treatment. The purpose of this in vivo study was to evaluate the effects of photofunctionalization on the intrabony stability of orthodontic titanium anchor screws and bone-anchor screw contact under immediate loading in growing rats. Custom-made titanium anchor screws (1.4 mm in diameter and 4.0 mm in length) with or without photofunctionalization pretreatment were placed on the proximal epiphysis of the tibial bone in 6-week-old male Sprague-Dawley rats and were loaded immediately after placement. After 2 weeks of loading, the stability of the anchor screws was evaluated using a Periotest device, and the bone-anchor screw contact ratio (BSC) was assessed by a histomorphometric analysis using field-emission scanning electron microscopy. In the unloaded group, Periotest values (PTVs) were ~25 for UV-untreated screws and 13 for UVtreated screws (P < .01), while in the immediate-loading group, PTVs were 28 for UV-untreated screws and 16 for UV-treated screws (P < .05). Significantly less screw mobility was observed in both UV-treated groups regardless of the loading protocol. The BSC was increased ~1.8 fold for UV-treated screws, compared with UV-untreated screws, regardless of the loading protocol. Photofunctionalization enhanced the intrabony stability of orthodontic anchor screws under immediate loading in growing rats by increasing bone-anchor screw contact.

Ringstone anchors from Gujarat, west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Gaur, A.S.; Sundaresh; Tripati, S.; Bandodkar, S.N.

of Dwarka and Somanath have yielded several ringstone anchors along with other stone anchors such as triangular and grapnel types. The raw material used for these ring stones comprises basalt, sandstone and limestone. Earlier, these anchors were identified...

Successful bone-anchored hearing aid implantation in a patient with osteogenesis imperfecta.

Science.gov (United States)

Coutinho, M B; Marques, C; Mendes, G J; Gonçalves, C

2015-11-01

To report a case of successful bone-anchored hearing aid implantation in an adult patient with type III osteogenesis imperfecta, which is commonly regarded as a contraindication to this procedure. A 45-year-old man with type III osteogenesis imperfecta presented with mixed hearing loss. There was a mild sensorineural component in both ears, with an air-bone gap between 45 and 50 dB HL. He was implanted with a bone-anchored hearing aid. The audiological outcome was good, with no complications and good implant stability (as measured by resonance frequency analysis). To our knowledge, this is the first recorded case of bone-anchored hearing aid implantation in a patient with osteogenesis imperfecta.

The Use of Comics-Based Cases in Anchored Instruction

Science.gov (United States)

Kneller, Matthew F.

2009-01-01

The primary purpose of this research was to understand how comics fulfill the role of anchor in an anchored instruction learning environment. Anchored instruction addresses the inert knowledge problem through the use of realistic multimedia stories, or "anchors," that embed a problem and the necessary data to solve it within the narrative. In the…

Effects of accuracy motivation and anchoring on metacomprehension judgment and accuracy.

Science.gov (United States)

Zhao, Qin

2012-01-01

The current research investigates how accuracy motivation impacts anchoring and adjustment in metacomprehension judgment and how accuracy motivation and anchoring affect metacomprehension accuracy. Participants were randomly assigned to one of six conditions produced by the between-subjects factorial design involving accuracy motivation (incentive or no) and peer performance anchor (95%, 55%, or no). Two studies showed that accuracy motivation did not impact anchoring bias, but the adjustment-from-anchor process occurred. Accuracy incentive increased anchor-judgment gap for the 95% anchor but not for the 55% anchor, which induced less certainty about the direction of adjustment. The findings offer support to the integrative theory of anchoring. Additionally, the two studies revealed a "power struggle" between accuracy motivation and anchoring in influencing metacomprehension accuracy. Accuracy motivation could improve metacomprehension accuracy in spite of anchoring effect, but if anchoring effect is too strong, it could overpower the motivation effect. The implications of the findings were discussed.

Dynamic performance of concrete undercut anchors for Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Mahrenholtz, Christoph, E-mail: christoph@mahrenholtz.net; Eligehausen, Rolf

2013-12-15

Graphical abstract: - Highlights: • Behavior of undercut anchors under dynamic actions simulating earthquakes. • First high frequency load and crack cycling tests on installed concrete anchors ever. • Comprehensive review of anchor qualification for Nuclear Power Plants. - Abstract: Post-installed anchors are widely used for structural and nonstructural connections to concrete. In many countries, concrete anchors used for Nuclear Power Plants have to be qualified to ensure reliable behavior even under extreme conditions. The tests required for qualification of concrete anchors are carried out at quasi-static loading rates well below the rates to be expected for dynamic actions deriving from earthquakes, airplane impacts or explosions. To investigate potentially beneficial effects of high loading rates and cycling frequencies, performance tests on installed undercut anchors were conducted. After introductory notes on anchor technology and a comprehensive literature review, this paper discusses the qualification of anchors for Nuclear Power Plants and the testing carried out to quantify experimentally the effects of dynamic actions on the load–displacement behavior of undercut anchors.

Investigation into the behaviour of concrete anchored diaphragm walls under earthquake condition

International Nuclear Information System (INIS)

Saba, H. R.; Rahaii, A. R.

2003-01-01

Diaphragm walls are frequently used in civil Engineering projects. Considering the variety and important volume of consumed materials (concrete, anchors and soil), one of the important factors for design and construction of these walls, are their behaviour under different executive, and loading conditions. In this paper, various models of concrete diaphragms with different number of anchors and soil parameters under static and dynamic loading have been investigated using finite element method with nonlinear models. Results including the internal forces in diaphragm walls, variation of forces in the anchors, shape of the sliding surface and variation of pressure in soil are obtained and compared. An experimental tool with suitable measurement systems for determining the pressure and internal forces was designed and realised. Also with similitude and dimensional analyses, diaphragms with different number of anchors were built and set on the shaking table test and experimented under different accelograms. Finally results of nonlinear dynamic analysis were compared with experimental results

Anchoring effect on first passage process in Taiwan financial market

Science.gov (United States)

Liu, Hsing; Liao, Chi-Yo; Ko, Jing-Yuan; Lih, Jiann-Shing

2017-07-01

Empirical analysis of the price fluctuations of financial markets has received extensive attention because a substantial amount of financial market data has been collected and because of advances in data-mining techniques. Price fluctuation trends can help investors to make informed trading decisions, but such decisions may also be affected by a psychological factors-the anchoring effect. This study explores the intraday price time series of Taiwan futures, and applies diffusion model and quantitative methods to analyze the relationship between the anchoring effect and price fluctuations during first passage process. Our results indicate that power-law scaling and anomalous diffusion for stock price fluctuations are related to the anchoring effect. Moreover, microscopic price fluctuations before switching point in first passage process correspond with long-term price fluctuations of Taiwan's stock market. We find that microscopic trends could provide useful information for understanding macroscopic trends in stock markets.

Surgical repair of central slip avulsion injuries with Mitek bone anchor--retrospective analysis of a case series.

LENUS (Irish Health Repository)

Chan, Jeffrey C Y

2007-01-01

The purpose of this study is to describe our technique of central slip repair using the Mitek bone anchor and to evaluate the treatment outcome. Eight digits in eight patients were reconstructed using the bone anchor: three little fingers, two middle fingers, two index fingers and one ring finger. There were two immediate and six delayed repairs (range from one day to eight months). Four patients had pre-operative intensive splinting and physiotherapy to restore passive extension of the proximal interphalangeal joint prior to central slip reconstruction. All patients have made good progress since surgery. No patient requires a second procedure and none of the bone anchors have dislodged or loosened. We conclude that the Mitek bone anchor is a reliable technique to achieve soft tissue to bone fixation in central slip avulsion injuries. We recommend that this technique be considered as a treatment option for patients requiring surgical repair.

Studies on the mechanical behavior of rock anchors. ; Results of in-situ pull-out tests. Rock anchor no rikigaku kyodo ni kansuru kenkyu. ; Gen prime ichi shiken ni okeru anchor no kyodo

Energy Technology Data Exchange (ETDEWEB)

Arimoto, K.; Ebisu, S.; Nakagawa, M.; Usui, M.; Someya, T.; Machida, N. (Okumura Corp., Tokyo (Japan))

1991-10-31

The rock anchor method is planned to apply to some permanent structures but since this method was developed for temporary structures, the clarification of the transferring mechanism of force from an anchor to a rockmass, the fracture mechanism and the development of the dynamic model have not been established. This paper arranged the data obtained by a full-scale, in-situ pulling out test of a rock anchor as the first step to understand the dynamic behavior and analyzed by paying attetion to the modulus of deformation of the rockmass where the anchor was embedded to elucidate the affecting degree of rockmass modulus of deformation, the embedded length and the tendon diameter on the dynamic behavior of the anchor. The rock anchor behavior could be expressed accurately by applying a theoretical solution derived by the balancing condition of forces at the boundary face. Especially, when the rockmass is uniform and the fracture occurrs at the interface between the tendon and grout, this approach can express the fracture with the accuracy similar to that made by the finite element method. 6 refs., 11 figs.,1 tab.

Containment liner plate anchors and steel embedments test results

International Nuclear Information System (INIS)

Chang-Lo, P.L.; Johnson, T.E.; Pfeifer, B.W.

1977-01-01

This paper summarizes test data on shear load and deformation capabilities for liner plate line anchors and structural steel embedments in reinforced and prestressed concrete nuclear containments. Reinforced and prestressed nuclear containments designed and constructed in the United States are lined with a minimum of 0.64 cm steel plate. The liner plates are anchored by the use of either studs or structural members (line anchors) which usually run in the vertical direction. This paper will only address line anchors. Static load versus displacement test data is necessary to assure that the design is adequate for the maximum loads. The test program for the liner anchors had the following major objectives: determine load versus displacement data for a variety of anchors considering structural tees and small beams with different weld configurations, from the preceding tests, determine which anchors would lead to an economical and extremely safe design and test these anchors for cyclic loads resulting from thermal fluctuations. Various concrete embeds in the containment and other structures are subjected to loads such as pipe rupture which results in shear. Since many of the loads are transient by nature, it is necessary to know the load-displacement relationship so that the energy absorption can be determined. The test program for the embeds had the following objectives: determine load-displacement relationship for various size anchors from 6.5 cm 2 to 26 cm 2 with maximum capacities of approximately 650 kN; determine the effect of various anchor width-to-thickness ratios for the same shear area

Predicting the Pullout Capacity of Small Ground Anchors Using Nonlinear Integrated Computing Techniques

Directory of Open Access Journals (Sweden)

Mosbeh R. Kaloop

2017-01-01

Full Text Available This study investigates predicting the pullout capacity of small ground anchors using nonlinear computing techniques. The input-output prediction model for the nonlinear Hammerstein-Wiener (NHW and delay inputs for the adaptive neurofuzzy inference system (DANFIS are developed and utilized to predict the pullout capacity. The results of the developed models are compared with previous studies that used artificial neural networks and least square support vector machine techniques for the same case study. The in situ data collection and statistical performances are used to evaluate the models performance. Results show that the developed models enhance the precision of predicting the pullout capacity when compared with previous studies. Also, the DANFIS model performance is proven to be better than other models used to detect the pullout capacity of ground anchors.

SNP discovery and chromosome anchoring provide the first physically-anchored hexaploid oat map and reveal synteny with model species.

Directory of Open Access Journals (Sweden)

Rebekah E Oliver

Full Text Available A physically anchored consensus map is foundational to modern genomics research; however, construction of such a map in oat (Avena sativa L., 2n = 6x = 42 has been hindered by the size and complexity of the genome, the scarcity of robust molecular markers, and the lack of aneuploid stocks. Resources developed in this study include a modified SNP discovery method for complex genomes, a diverse set of oat SNP markers, and a novel chromosome-deficient SNP anchoring strategy. These resources were applied to build the first complete, physically-anchored consensus map of hexaploid oat. Approximately 11,000 high-confidence in silico SNPs were discovered based on nine million inter-varietal sequence reads of genomic and cDNA origin. GoldenGate genotyping of 3,072 SNP assays yielded 1,311 robust markers, of which 985 were mapped in 390 recombinant-inbred lines from six bi-parental mapping populations ranging in size from 49 to 97 progeny. The consensus map included 985 SNPs and 68 previously-published markers, resolving 21 linkage groups with a total map distance of 1,838.8 cM. Consensus linkage groups were assigned to 21 chromosomes using SNP deletion analysis of chromosome-deficient monosomic hybrid stocks. Alignments with sequenced genomes of rice and Brachypodium provide evidence for extensive conservation of genomic regions, and renewed encouragement for orthology-based genomic discovery in this important hexaploid species. These results also provide a framework for high-resolution genetic analysis in oat, and a model for marker development and map construction in other species with complex genomes and limited resources.

Correlation of Persistence, Initiative and Career Anchors Categories of Students

Directory of Open Access Journals (Sweden)

I A Novikova

2008-03-01

Full Text Available The article is devoted to the analysis of the results of comparative empirical study of persistence, initiative and Career Anchors categories of the students on the basis of the systemic-functional approach.

Mitek Anchor System: a new technique for tenodesis and ligamentous repair of the foot and ankle.

Science.gov (United States)

Pederson, B; Tesoro, D; Wertheimer, S J; Coraci, M

1991-01-01

The authors present an alternative method for securing tendon and ligaments to bone, utilizing the Mitek Anchor System. The description of the Mitek system and technique of application is presented. Technical simplicity and ease of adaptability within the foot and ankle are distinct advantages of this System.

Adsorption phenomena and anchoring energy in nematic liquid crystals

CERN Document Server

Barbero, Giovanni

2005-01-01

Despite the large quantity of phenomenological information concerning the bulk properties of nematic phase liquid crystals, little is understood about the origin of the surface energy, particularly the surface, interfacial, and anchoring properties of liquid crystals that affect the performance of liquid crystal devices. Self-contained and unique, Adsorption Phenomena and Anchoring Energy in Nematic Liquid Crystals provides an account of new and established results spanning three decades of research into the problems of anchoring energy and adsorption phenomena in liquid crystals.The book contains a detailed discussion of the origin and possible sources of anchoring energy in nematic liquid crystals, emphasizing the dielectric contribution to the anchoring energy in particular. Beginning with fundamental surface and anchoring properties of liquid crystals and the definition of the nematic phase, the authors explain how selective ion adsorption, dielectric energy density, thickness dependence, and bias voltage...

Bone-anchored hearing devices in children with unilateral conductive hearing loss: a patient-carer perspective.

Science.gov (United States)

Banga, Rupan; Doshi, Jayesh; Child, Anne; Pendleton, Elizabeth; Reid, Andrew; McDermott, Ann-Louise

2013-09-01

We sought to determine the outcome of implantation of a bone-anchored hearing device in children with unilateral conductive hearing loss. A retrospective case note analysis was used in a tertiary referral pediatric hospital to study 17 consecutive cases of pediatric patients with unilateral conductive hearing loss who were fitted with a bone-anchored hearing device between 2005 and 2010. The average age of the patients at the time of bone-anchored hearing device fitting was 10 years 6 months (range, 6 years 3 months to 16 years). Qualitative subjective outcome measures demonstrated benefit. The vast majority of patients reported improved social and physical functioning and improved quality of life. All 17 patients are currently using their bone-anchored hearing device on a daily basis after a follow-up of 6 months. This study has shown improved quality of life in children with unilateral hearing loss after implantation of their bone-anchored hearing device. There was a high degree of patient satisfaction and improvement in health status reported by children and/or carers. Bone-anchored hearing devices have an important role in the management of children with symptomatic unilateral hearing loss. Perhaps earlier consideration of a bone-anchored hearing device would be appropriate in selected cases.

Outcomes of the modified Brostrom procedure using suture anchors for chronic lateral ankle instability--a prospective, randomized comparison between single and double suture anchors.

Science.gov (United States)

Cho, Byung-Ki; Kim, Yong-Min; Kim, Dong-Soo; Choi, Eui-Sung; Shon, Hyun-Chul; Park, Kyoung-Jin

2013-01-01

The present prospective, randomized study was conducted to compare the clinical outcomes of the modified Brostrom procedure using single and double suture anchors for chronic lateral ankle instability. A total of 50 patients were followed up for more than 2 years after undergoing the modified Brostrom procedure. Of the 50 procedures, 25 each were performed using single and double suture anchors by 1 surgeon. The Karlsson scale had improved significantly to 89.8 points and 90.6 points in the single and double anchor groups, respectively. Using the Sefton grading system, 23 cases (92%) in the single anchor group and 22 (88%) in the double anchor group achieved satisfactory results. The talar tilt angle and anterior talar translation on stress radiographs using the Telos device had improved significantly to an average of 5.7° and 4.6 mm in the single anchor group and 4.5° and 4.3 mm in the double anchor group, respectively. The double anchor technique was superior with respect to the postoperative talar tilt. The single and double suture anchor techniques produced similar clinical and functional outcomes, with the exception of talar tilt as a reference of mechanical stability. The modified Brostrom procedure using both single and double suture anchors appears to be an effective treatment method for chronic lateral ankle instability. Copyright © 2013 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

Bearing Capacity Analyses for the Great Belt East Bridge Anchor Blocks

DEFF Research Database (Denmark)

Sørensen, Carsten Steen; Clausen, Carl J. Frimann; Andersen, Henrik

1993-01-01

This paper presents a comparison between different methods of bearing capacity analyses: Upper Bound Method. Limit Equilibrium Analysis and Finite Element Analysis. For the Great Belt East Bridge anchor blocks it was concluded that these methods of calculation agree within 5%. However, for cases ...

The utilisation of a career conversation framework based on Schein’s career anchors model

Directory of Open Access Journals (Sweden)

Magda Bezuidenhout

2013-07-01

Full Text Available Orientation: This  study  constituted  and  reported  on  the  outcomes  of  a  structured  career conversation  framework  based  on  Schein’s  eight  career  anchors  in  an  open  distance  and e-learning (ODeL university in South Africa. Research purpose: The purpose of the research was to report on the utilisation of a structured career conversation framework based on Schein’s career anchors model. Motivation for the study: The rationale for the study was the paucity of studies investigating career anchors in South Africa’s multicultural organisational context. Research design, approach and method: A quantitative approach was adopted in the study. The population consisted of 4200 employees at a university in South Africa. Statistical analysis was performed using one-way analysis of variance (ANOVA as well as a Scheffe post hoc test. Main  findings: The  findings  of  this  study  suggest  that  career  conversation  has  a  dynamic nature (i.e. it changes over a period of time. Consequently, career development interventions in the workplace need to approach the workforce holistically. Practical/managerial implications: The findings and results will assist managers, practitioners and  career  development  specialists  in  the  practical  implementation  of  the  career  anchor concept. Contribution/value-add: The career conversation framework based on Schein’s career anchors has expanded the existing theory to find the right balance between career conversations and career anchors to keep people motivated to perform optimally in an organisation.

Stress analysis of liners for prestressed concrete reactor pressure vessels with regard to non-linear behaviour of liner material and of anchor-characteristics

International Nuclear Information System (INIS)

Oberpichler, R.; Schnellenbach, G.

1975-01-01

The thin liner attached by anchors like a membrane to the interior wall of a prestressed concrete reactor pressure vessel (PCRV) has to provide the leak-tightness of the vessel. Furthermore the liner may serve as internal shuttering for placing of concrete as well as a support for the cooling system. The two-dimensional behaviour of the liner is investigated with regard to non-linear anchor-characteristics and non-linear material behaviour of the liner. The analysis is based on a plane stress model under the assumption of a membrane state of the liner. Calculations are performed by the dynamic relaxation method. With the aid of available non-linear stress-strain diagrams, describing the post-buckling behaviour, individual panels are considered as buckled ones. The adjacent unbuckled panels are calculated on other non-linear diagrams. Strains and stresses in the liner and additional shear loads in the anchors can be calculated with arbitrary sizing and spacing of the anchors. With respect to the parameters they are easily controlled. Since actual loads on the liner are defined by the PCRV-behaviour, an economical and safe design is possible. Finally an extreme case is calculated to assess the maximum value of the shear-forces assuming zero post-buckling capacity for the buckled panel. (Auth.)

Self-tapping ability of carbon fibre reinforced polyetheretherketone suture anchors.

Science.gov (United States)

Feerick, Emer M; Wilson, Joanne; Jarman-Smith, Marcus; Ó'Brádaigh, Conchur M; McGarry, J Patrick

2014-10-01

An experimental and computational investigation of the self-tapping ability of carbon fibre reinforced polyetheretherketone (CFR-PEEK) has been conducted. Six CFR-PEEK suture anchor designs were investigated using PEEK-OPTIMA® Reinforced, a medical grade of CFR-PEEK. Experimental tests were conducted to investigate the maximum axial force and torque required for self-taping insertion of each anchor design. Additional experimental tests were conducted for some anchor designs using pilot holes. Computational simulations were conducted to determine the maximum stress in each anchor design at various stages of insertion. Simulations also were performed to investigate the effect of wall thickness in the anchor head. The maximum axial force required to insert a self-tapping CFR-PEEK suture anchor did not exceed 150 N for any anchor design. The maximum torque required to insert a self-tapping CFR-PEEK suture anchor did not exceed 0.8 Nm. Computational simulations reveal significant stress concentrations in the region of the anchor tip, demonstrating that a re-design of the tip geometry should be performed to avoid fracture during self-tapping, as observed in the experimental component of this study. This study demonstrates the ability of PEEK-OPTIMA Reinforced suture anchors to self-tap polyurethane foam bone analogue. This provides motivation to further investigate the self-tapping ability of CFR-PEEK suture anchors in animal/cadaveric bone. An optimised design for CFR-PEEK suture anchors offers the advantages of radiolucency, and mechanical properties similar to bone with the ability to self-tap. This may have positive implications for reducing surgery times and the associated costs with the procedure. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Career anchors and values from different career management perspectives

Directory of Open Access Journals (Sweden)

Rodrigo Cunha da Silva

2016-06-01

Full Text Available Purpose – To analyze the relationships between career anchors and young Generation Y professionals’ values, from the career concept perspective. Design/methodology/approach – Research concerning the proposed objective was carried out through quantitative research involving 189 Business Administration majors from a Catholic university in São Paulo, Brazil. We used two instruments to identify the career anchors and values of respondents: Schein (1990 and Schwartz (1994, respectively. We used statistical techniques to explore the relationships between career anchors and values. Findings – Among the results, mention should be made to the statistical relationships found between analyzed career anchors and values. It is also important to stress that, although the Lifestyle career anchor was predominantly present in the conglomerate division, this anchor was the predominant characteristic in the differentiation of the smaller group of respondents, the new career group. The General Management Career Anchor, which presents a lower incidence, is the predominant characteristic of the larger group, referring to organizational careers. As well as the Lifestyle career anchor, the Hedonism value was predominant among respondents. Originality/value – The need to consider the following was found: Generation Y presents generational characteristics that drive people management to propose work structures that offer activities to generate learning, pleasure, self-fulfillment and conciliation between work and personal life.

Test Score Equating Using Discrete Anchor Items versus Passage-Based Anchor Items: A Case Study Using "SAT"® Data. Research Report. ETS RR-14-14

Science.gov (United States)

Liu, Jinghua; Zu, Jiyun; Curley, Edward; Carey, Jill

2014-01-01

The purpose of this study is to investigate the impact of discrete anchor items versus passage-based anchor items on observed score equating using empirical data.This study compares an "SAT"® critical reading anchor that contains more discrete items proportionally, compared to the total tests to be equated, to another anchor that…

On Moderator Detection in Anchoring Research: Implications of Ignoring Estimate Direction

Directory of Open Access Journals (Sweden)

Nathan N. Cheek

2018-05-01

Full Text Available Anchoring, whereby judgments assimilate to previously considered standards, is one of the most reliable effects in psychology. In the last decade, researchers have become increasingly interested in identifying moderators of anchoring effects. We argue that a drawback of traditional moderator analyses in the standard anchoring paradigm is that they ignore estimate direction—whether participants’ estimates are higher or lower than the anchor value. We suggest that failing to consider estimate direction can sometimes obscure moderation in anchoring tasks, and discuss three potential analytic solutions that take estimate direction into account. Understanding moderators of anchoring effects is essential for a basic understanding of anchoring and for applied research on reducing the influence of anchoring in real-world judgments. Considering estimate direction reduces the risk of failing to detect moderation.

Design and Vibration Sensitivity Analysis of a MEMS Tuning Fork Gyroscope with an Anchored Diamond Coupling Mechanism

Directory of Open Access Journals (Sweden)

Yanwei Guan

2016-04-01

Full Text Available In this paper, a new micromachined tuning fork gyroscope (TFG with an anchored diamond coupling mechanism is proposed while the mode ordering and the vibration sensitivity are also investigated. The sense-mode of the proposed TFG was optimized through use of an anchored diamond coupling spring, which enables the in-phase mode frequency to be 108.3% higher than the anti-phase one. The frequencies of the in- and anti-phase modes in the sense direction are 9799.6 Hz and 4705.3 Hz, respectively. The analytical solutions illustrate that the stiffness difference ratio of the in- and anti-phase modes is inversely proportional to the output induced by the vibration from the sense direction. Additionally, FEM simulations demonstrate that the stiffness difference ratio of the anchored diamond coupling TFG is 16.08 times larger than the direct coupling one while the vibration output is reduced by 94.1%. Consequently, the proposed new anchored diamond coupling TFG can structurally increase the stiffness difference ratio to improve the mode ordering and considerably reduce the vibration sensitivity without sacrificing the scale factor.

Biased calculations: Numeric anchors influence answers to math equations

Directory of Open Access Journals (Sweden)

Andrew R. Smith

2011-02-01

Full Text Available People must often perform calculations in order to produce a numeric estimate (e.g., a grocery-store shopper estimating the total price of his or her shopping cart contents. The current studies were designed to test whether estimates based on calculations are influenced by comparisons with irrelevant anchors. Previous research has demonstrated that estimates across a wide range of contexts assimilate toward anchors, but none has examined estimates based on calculations. In two studies, we had participants compare the answers to math problems with anchors. In both studies, participants' estimates assimilated toward the anchor values. This effect was moderated by time limit such that the anchoring effects were larger when the participants' ability to engage in calculations was limited by a restrictive time limit.

Contact area and pressure in suture bridge rotator cuff repair using knotless lateral anchors.

Science.gov (United States)

Tompkins, Marc; Monchik, Keith O; Plante, Matthew J; Fleming, Braden C; Fadale, Paul D

2011-10-01

To evaluate whether the use of knotless lateral anchors in a suture bridge construct produces better contact area and pressure parameters than a suture bridge construct with standard lateral anchors that require knots or a double-row repair. The hypothesis was that knotless lateral anchors would produce better contact area and pressure parameters than the other two constructs. A total of fifteen matched pairs of cadaveric shoulders were divided into three groups. In Group 1, a suture bridge using knotless anchors for the lateral row was performed on five shoulders. A suture bridge using standard lateral row anchors that require knots was performed on the contralateral shoulders. In Group 2, suture bridge with knotless lateral row anchors was compared with double-row repair. In Group 3, suture bridge using standard lateral row anchors was compared with double-row repair. The contact conditions of the rotator cuff footprint were measured using pressure-sensitive film. There were no statistically significant differences between any of the techniques regarding contact area F(2, 15.7) = 3.09, P = 0.07 or mean contact pressure F(2, 15.1) = 2.35, P = 0.12. A post hoc power analysis suggests differences between techniques are likely less than 91-113 mm(2) for area and 0.071-0.089 N for pressure. The use of knotless anchors in the lateral row of a suture bridge repair did not increase the footprint contact area or contact pressure when compared to a suture bridge repair requiring knots laterally or to a double-row repair.

76 FR 30301 - Commercial Acquisition; Anchor Tenancy

Science.gov (United States)

2011-05-25

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION 48 CFR Part 1812 RIN 2700-AD64 Commercial... consistent with NASA's authority under Section 401 of the Commercial Space Competitiveness Act (CSCA) of 1992. NASA may enter into multi-year anchor tenancy contracts for commercial space goods or services. Anchor...

A comparison of lateral ankle ligament suture anchor strength.

Science.gov (United States)

Barber, F Alan; Herbert, Morley A; Crates, John M

2013-06-01

Lateral ankle ligament repairs increasingly use suture anchors instead of bone tunnels. Our purpose was to compare the biomechanical properties of a knotted and knotless suture anchor appropriate for a lateral ankle ligament reconstruction. In porcine distal fibulae, 10 samples of 2 different PEEK anchors were inserted. The attached sutures were cyclically loaded between 10N and 60N for 200 cycles. A destructive pull was performed and failure loads, cyclic displacement, stiffness, and failure mode recorded. PushLock 2.5 anchors failed before 200 cycles. PushLock 100 cycle displacement was less than Morphix 2.5 displacement (panchors completing 200 cycles was 86.5N (PushLock) and 252.1N (Morphix) (panchor breaking and suture breakage. The knotted Morphix demonstrated more displacement and greater failure strength than the knotless PushLock. The PushLock failed consistently with suture breaking. The Morphix anchor failed both by anchor breaking and by suture breaking. Copyright © 2012 European Foot and Ankle Society. Published by Elsevier Ltd. All rights reserved.

Post-installed concrete anchors in nuclear power plants: Performance and qualification

International Nuclear Information System (INIS)

Mahrenholtz, Philipp; Eligehausen, Rolf

2015-01-01

Graphical abstract: - Highlights: • Review of qualification and design regulations for anchors in nuclear power plants. • First complete set of nuclear anchor load–displacement data and its evaluation ever. • Demonstration of robust test behavior of a qualified post-installed anchor product. - Abstract: In nuclear power plants (NPPs), post-installed anchors are widely used for structural and non-structural connections to concrete. In many countries, anchor products employed for safety relevant applications have to be approved by the authorities. For the high safety standards in force for NPPs, special requirements have to be met to allow for extreme design situations. This paper presents an experimental test program conducted to evaluate the performance of anchors according to the German Guideline for Anchorages in Nuclear Power Plants and Nuclear Technology Installations (DIBt KKW Leitfaden, 2010). After a brief introduction to anchor behavior and the regulative context, the results of tension and shear tests carried out on undercut anchors are discussed. Robust load capacities and relatively small displacements determined for demanding load and crack cycling tests demonstrated the suitability of anchors qualified according to a state-of-the-art qualification guideline

Anchorage Behaviors of Frictional Tieback Anchors in Silty Sand

Science.gov (United States)

Hsu, Shih-Tsung; Hsiao, Wen-Ta; Chen, Ke-Ting; Hu, Wen-Chi; Wu, Ssu-Yi

2017-06-01

Soil anchors are extensively used in geotechnical applications, most commonly serve as tieback walls in deep excavations. To investigate the anchorage mechanisms of this tieback anchor, a constitutive model that considers both strain hardening and softening and volume dilatancy entitled SHASOVOD model, and FLAC3D software are used to perform 3-D numerical analyses. The results from field anchor tests are compared with those calculated by numerical analyses to enhance the applicability of the numerical method. After the calibration, this research carried out the parameter studies by numerical analyses. The numerical results reveal that whether the yield of soil around an anchor develops to ground surface and/or touches the diaphragm wall depending on the overburden depth H and the embedded depth Z of an anchor, this study suggests the minimum overburden and embedded depths to avoid the yield of soils develop to ground surface and/or touch the diaphragm wall. When the embedded depth, overburden depth or fixed length of an anchor increases, the anchorage capacity also increases. Increasing fixed length should be the optimum method to increase the anchorage capacity for fixed length less than 20m. However, when the fixed length of an anchor exceeds 30 m, the increasing rate of anchorage capacity per fixed length decreases, and progressive yield occurs obviously between the fixed length and surrounding soil.

Link Anchors in Images: Is there Truth?

NARCIS (Netherlands)

Aly, Robin; McGuinness, Kevin; Kleppe, Martijn; Ordelman, Roeland J.F.; O'Connor, Noel; de Jong, Franciska M.G.

2012-01-01

While automatic linking in text collections is well understood, little is known about links in images. In this work, we investigate two aspects of anchors, the origin of a link, in images: 1) the requirements of users for such anchors, e.g. the things users would like more information on, and 2)

The Effect of Mini and Midi Anchor Tests on Test Equating

Science.gov (United States)

Arikan, Çigdem Akin

2018-01-01

The main purpose of this study is to compare the test forms to the midi anchor test and the mini anchor test performance based on item response theory. The research was conducted with using simulated data which were generated based on Rasch model. In order to equate two test forms the anchor item nonequivalent groups (internal anchor test) was…

Use of the ROC anchor in foot and ankle surgery. A retrospective study.

Science.gov (United States)

Kuwada, G T

1999-05-01

A retrospective study was conducted on the use of the ROC (Radial Osteo Compression) soft-tissue anchor in foot and ankle surgery. This article describes how the anchor is deployed, problematic aspects of using the anchor, and complications and success rates associated with the anchor in ankle stabilizations, posterior tibial tendon reconstruction, peroneus brevis tendon reconstruction after fracture of the base of the fifth metatarsal, and detachment and reattachment of the Achilles tendon. The ROC anchor consists of the anchor with nonabsorbable suture attached to the shaft, the deployment handle, and drill bits. The anchor and shaft are snapped into the deployment handle and inserted into the drill hole. Compression of the trigger deploys the anchor into the hole. The ROC anchor was found to be reliable, useful, and relatively easy to deploy, with outcomes similar to those of other soft-tissue anchors.

Anchoring Proteins as Regulators of Signaling Pathways

Science.gov (United States)

Perino, Alessia; Ghigo, Alessandra; Scott, John D.; Hirsch, Emilio

2012-01-01

Spatial and temporal organization of signal transduction is coordinated through the segregation of signaling enzymes in selected cellular compartments. This highly evolved regulatory mechanism ensures the activation of selected enzymes only in the vicinity of their target proteins. In this context, cAMP-responsive triggering of protein kinase A is modulated by a family of scaffold proteins referred to as A-kinase anchoring proteins. A-kinase anchoring proteins form the core of multiprotein complexes and enable simultaneous but segregated cAMP signaling events to occur in defined cellular compartments. In this review we will focus on the description of A-kinase anchoring protein function in the regulation of cardiac physiopathology. PMID:22859670

On the Robustness of Anchoring Effects in WTP and WTA Experiments

OpenAIRE

Drew Fudenberg; David K Levine; Zacharias Maniadis

2010-01-01

We reexamine the effects of the anchoring manipulation of Ariely, Loewenstein, and Prelec (2003) on the evaluation of common market goods and find very weak anchoring effects. We perform the same manipulation on the evaluation of binary lotteries, and find no anchoring effects at all. This suggests limits on the robustness of anchoring effects. (JEL C91, D12, D44)

Career Paths, Images and Anchors: A Study with Brazilian Professionals

Science.gov (United States)

Kilimnik, Zelia Miranda; de Oliveira, Luiz Claudio Vieira; Sant'anna, Anderson De Souza; Barros, Delba Teixeira Rodrigues

2011-01-01

This article analyses career anchors changes associated to images and professionals trajectories. Its main question: Do anchors careers change through time? We conducted twelve interviews involving professionals from the Administration Area, applying Schein's Career Anchors Inventory (1993). We did the same two years later. In both of them, the…

Stone anchors of India: Findings, classification and significance.

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.

Various types of stone anchors have been observed during inshore and offshore explorations along the east and west coasts of India. The earliest stone anchors of India have been recorded from the Harappan sites (3rd millennium BC), but their shape...

Investigation of suction anchor pullout capacity under undrained conditions

OpenAIRE

Jarand, Pollestad

2015-01-01

Master's thesis in Offshore technology Floating units are dependent on reliable mooring systems to ensure safety during marine operations. Suction anchors have proved to be a technologically viable and cost-effective concept. They are capable of precision installation, re-use, and provide large resistive capacity. This thesis investigates load capacity and failure modes of suction anchors subjected to vertical, horizontal (lateral), and incline loading. Suction anchor design co...

Pyramidal anchor stone from Baga waters of Goa, west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.

. Pyramidal anchor stones have an apex hole which goes up to the round hole, however Goa anchor stone has no such perforation, but, instead has a rectangular cutting on the apex. The anchor stone is compared with Greek pyramidal anchor stones, and probably...

Employees’ work engagement and job commitment: The moderating role of career anchors

Directory of Open Access Journals (Sweden)

Melinde Coetzee

2014-08-01

Research purpose: The objective of the present study was to assess whether individuals’career anchors (measured by the career orientations inventory significantly moderate therelationship between their work engagement (measured by the Utrecht work engagementscale and job commitment (measured by the organisation-related commitment scale. Motivation for the study: Although the literature review suggests that people’s workengagement and job commitment may be influenced by their career anchors, there seems to bea paucity of research examining the interaction effects between these three variables. Research approach, design and method: A cross-sectional quantitative survey approach wasused. A non-probability purposive sample of adults (N = 318 employed in a human resourcecapacity in the South African service industry participated in the study. Stepwise hierarchicalmoderated regression analysis was performed to achieve the objective of the study. Main findings: The results showed that the work engagement-job commitment relationshipwas generally stronger for high career anchor preferences than for low career anchorpreferences.Practical/managerial implications: The results of the study can be useful when human resourceinterventions for enhancing employees’ engagement and commitment are developed. Contribution: The results of the study add new insights to the career literature by showing thatpeople’s career self-concepts (as reflected by their career anchors are important to consider inenhancing their work engagement and job commitment.

Peptide-Mediated Liposome Fusion: The Effect of Anchor Positioning

Directory of Open Access Journals (Sweden)

Niek S. A. Crone

2018-01-01

Full Text Available A minimal model system for membrane fusion, comprising two complementary peptides dubbed “E” and “K” joined to a cholesterol anchor via a polyethyleneglycol spacer, has previously been developed in our group. This system promotes the fusion of large unilamellar vesicles and facilitates liposome-cell fusion both in vitro and in vivo. Whilst several aspects of the system have previously been investigated to provide an insight as to how fusion is facilitated, anchor positioning has not yet been considered. In this study, the effects of placing the anchor at either the N-terminus or in the center of the peptide are investigated using a combination of circular dichroism spectroscopy, dynamic light scattering, and fluorescence assays. It was discovered that anchoring the “K” peptide in the center of the sequence had no effect on its structure, its ability to interact with membranes, or its ability to promote fusion, whereas anchoring the ‘E’ peptide in the middle of the sequence dramatically decreases fusion efficiency. We postulate that anchoring the ‘E’ peptide in the middle of the sequence disrupts its ability to form homodimers with peptides on the same membrane, leading to aggregation and content leakage.

Testing methods of steel wi re ropes at the anchor

Directory of Open Access Journals (Sweden)

Stanislav Kropuch

2012-12-01

Full Text Available The present paper introduces an application of the acoustic andthermographic method in the defectoscopic testing of immobilesteel wire ropes at the most critical point, the anchor. Firstmeasurements and their results by these new defectoscopic methodsare shown. In defectoscopic tests at the anchor, the widelyused magnetic method gives unreliable results, and therefore presentsa problem for steel wire defectoscopy. Application of the two new methods in the steel wire defectoscopy at the anchor point will enableincreased safety measures at the anchor of steel wire ropes in bridge, roof, tower and aerial cable lift constructions.

Anchored enrichment dataset for true flies (order Diptera) reveals insights into the phylogeny of flower flies (family Syrphidae).

Science.gov (United States)

Young, Andrew Donovan; Lemmon, Alan R; Skevington, Jeffrey H; Mengual, Ximo; Ståhls, Gunilla; Reemer, Menno; Jordaens, Kurt; Kelso, Scott; Lemmon, Emily Moriarty; Hauser, Martin; De Meyer, Marc; Misof, Bernhard; Wiegmann, Brian M

2016-06-29

Anchored hybrid enrichment is a form of next-generation sequencing that uses oligonucleotide probes to target conserved regions of the genome flanked by less conserved regions in order to acquire data useful for phylogenetic inference from a broad range of taxa. Once a probe kit is developed, anchored hybrid enrichment is superior to traditional PCR-based Sanger sequencing in terms of both the amount of genomic data that can be recovered and effective cost. Due to their incredibly diverse nature, importance as pollinators, and historical instability with regard to subfamilial and tribal classification, Syrphidae (flower flies or hoverflies) are an ideal candidate for anchored hybrid enrichment-based phylogenetics, especially since recent molecular phylogenies of the syrphids using only a few markers have resulted in highly unresolved topologies. Over 6200 syrphids are currently known and uncovering their phylogeny will help us to understand how these species have diversified, providing insight into an array of ecological processes, from the development of adult mimicry, the origin of adult migration, to pollination patterns and the evolution of larval resource utilization. We present the first use of anchored hybrid enrichment in insect phylogenetics on a dataset containing 30 flower fly species from across all four subfamilies and 11 tribes out of 15. To produce a phylogenetic hypothesis, 559 loci were sampled to produce a final dataset containing 217,702 sites. We recovered a well resolved topology with bootstrap support values that were almost universally >95 %. The subfamily Eristalinae is recovered as paraphyletic, with the strongest support for this hypothesis to date. The ant predators in the Microdontinae are sister to all other syrphids. Syrphinae and Pipizinae are monophyletic and sister to each other. Larval predation on soft-bodied hemipterans evolved only once in this family. Anchored hybrid enrichment was successful in producing a robustly supported

Design method of redundancy of brace-anchor sharing supporting based on cooperative deformation

Science.gov (United States)

Liu, Jun-yan; Li, Bing; Liu, Yan; Cai, Shan-bing

2017-11-01

Because of the complicated environment requirement, the support form of foundation pit is diversified, and the brace-anchor sharing support is widely used. However, the research on the force deformation characteristics and the related aspects of the cooperative response of the brace-anchor sharing support is insufficient. The application of redundancy theory in structural engineering has been more mature, but there is little theoretical research on redundancy theory in underground engineering. Based on the idea of collaborative deformation, the paper calculates the ratio of the redundancy degree of the cooperative deformation by using the local reinforcement design method and the structural component redundancy parameter calculation formula based on Frangopol. Combined with the engineering case, through the calculation of the ratio of cooperative deformation redundancy in the joint of brace-anchor sharing support. This paper explores the optimal anchor distribution form under the condition of cooperative deformation, and through the analysis and research of displacement field and stress field, the results of the collaborative deformation are validated by comparing the field monitoring data. It provides theoretical basis for the design of this kind of foundation pit in the future.

Cultural Anchors and the Organization of Differences: A Multi-method Analysis of LGBT Marches on Washington

Science.gov (United States)

Ghaziani, Amin; Baldassarri, Delia

2013-01-01

Social scientists describe culture as either coherent or incoherent and political dissent as either unifying or divisive. This article moves beyond such dichotomies. Content, historical, and network analyses of public debates on how to organize four lesbian, gay, bisexual, and transgender (LGBT) Washington marches provide evidence for an integrative position. Rather than just describe consistencies or contradictions, we contend that the key analytic challenge is to explain the organization of differences. We propose one way of doing this using the mechanism of a cultural anchor. Within and across marches, a small collection of ideas remains fixed in the national conversation, yet in a way that allows activists to address their internal diversity and respond to unfolding historical events. These results suggest that activists do not simply organize around their similarities but, through cultural anchors, they use their commonalities to build a thinly coherent foundation that can also support their differences. Situated at the nexus of culture, social movements, sexualities, and networks, this article demonstrates how the anchoring mechanism works in the context of LGBT political organizing. PMID:23661809

Inelastic seismic behavior of post-installed anchors for nuclear safety related structures: Generation of experimental database

Energy Technology Data Exchange (ETDEWEB)

Mahadik, Vinay, E-mail: vinay.mahadik@iwb.uni-stuttgart.de; Sharma, Akanshu; Hofmann, Jan

2016-02-15

Highlights: • Experiments for evaluating seismic behavior of anchors were performed. • Two undercut anchor products in use in nuclear facilities were considered. • Monotonic tension, shear and cycling tension tests at different crack widths. • Crack cycling tests at constant, in-phase and out-of phase tension loads. • Characteristics for the two anchors as a function of crack width were identified. - Abstract: Post installed (PI) anchors are often employed for connections between concrete structure and components or systems in nuclear power plants (NPP) and related facilities. Standardized practices for nuclear related structures demand stringent criteria, which an anchor has to satisfy in order to qualify for use in NPP related structures. In NPP and related facilities, the structure–component interaction in the event of an earthquake depends on the inelastic behavior of the concrete structure, the component system and also the anchorage system that connects them. For analysis, anchorages are usually assumed to be rigid. Under seismic actions, however, it is known that anchors may undergo significant plastic displacement and strength degradation. Analysis of structure–component interaction under seismic loads calls for numerical models simulating inelastic behavior of anchorage systems. A testing program covering different seismic loading scenarios in a reasonably conservative manner is required to establish a basis for generating numerical models of anchorage systems. Currently there is a general lack of modeling techniques to consider the inelastic behavior of anchorages in structure–component interaction under seismic loads. In this work, in view of establishing a basis for development of numerical models simulating the inelastic behavior of anchors, seismic tests on two different undercut anchors qualified for their use in NPP related structures were carried out. The test program was primarily based on the DIBt-KKW-Leitfaden (2010) guidelines

Assessing tether anchor labeling and usability in pickup trucks.

Science.gov (United States)

Klinich, Kathleen D; Manary, Miriam A; Malik, Laura A; Flannagan, Carol A; Jermakian, Jessica S

2018-04-03

The objective of this study was to investigate vehicle factors associated with child restraint tether use and misuse in pickup trucks and evaluate 4 labeling interventions designed to educate consumers on proper tether use. Volunteer testing was performed with 24 subjects and 4 different pickup trucks. Each subject performed 8 child restraint installations among the 4 pickups using 2 forward-facing restraints: a Britax Marathon G4.1 and an Evenflo Triumph. Vehicles were selected to represent 4 different implementations of tether anchors among pickups: plastic loop routers (Chevrolet Silverado), webbing routers (Ram), back wall anchors (Nissan Frontier), and webbing routers plus metal anchors (Toyota Tundra). Interventions included a diagram label, Quick Response (QR) Code linked to video instruction, coordinating text label, and contrasting text tag. Subjects used the child restraint tether in 93% of trials. However, tether use was completely correct in only 9% of trials. An installation was considered functional if the subject attached the tether to a tether anchor and had a tight installation (ignoring routing and head restraint position); 28% of subjects achieved a functional installation. The most common installation error was attaching the tether hook to the anchor/router directly behind the child restraint (near the top of the seatback) rather than placing the tether through the router and attaching it to the anchor in the adjacent seating position. The Nissan Frontier, with the anchor located on the back wall of the cab, had the highest rate of correct installations but also had the highest rate of attaching the tether to components other than the tether anchor (seat adjustor, child restraint storage hook, around head restraint). None of the labeling interventions had a significant effect on correct installation; not a single subject scanned the QR Code to access the video instruction. Subjects with the most successful installations spent extensive time

Anchoring submersible ultrasonic receivers in river channels with stable substrate

Science.gov (United States)

Bettoli, Phillip William; Scholten, G.D.; Hubbs, D.

2010-01-01

We developed an anchoring system for submersible ultrasonic receivers (SURs) that we placed on the bottom of the riverine reaches of three main-stem reservoirs in the upper Tennessee River. Each anchor consisted of a steel tube (8.9 x 35.6 cm) welded vertically to a round plate of steel (5.1 x 40.6 cm). All seven SURs and their 57-kg anchors were successfully deployed and retrieved three times over 547 d by a dive team employing surface air-breathing equipment and a davit-equipped boat. All of the anchors and their SURs remained stationary over two consecutive winters on the hard-bottom, thalweg sites where they were deployed. The SUR and its anchor at the most downriver site experienced flows that exceeded 2,100 m(3)/s and mean water column velocities of about 0.9 m/s.

Do budget balance rules anchor budget balance expectations? -- Some international evidence

OpenAIRE

Rülke, Jan-Christoph; Frenkel, Michael; Lis, Eliza

2013-01-01

This is the first study that analyzes whether budget balance expectations are anchored and whether budget balance rules effectively anchor expectations. To this end, we use a unique data set which covers budget balance expectations in 17 countries that implemented a budget balance rules. While our results are mixed concerning the general impact of budget balance rules on anchoring expectations, we do find that specific features of budget balance rules are important to successfully anchor budg...

Ultimate load capacities of expansion anchor bolts

International Nuclear Information System (INIS)

Czarnecki, R.M.; Manrique, M.A.; Samaddar, S.K.

1993-01-01

A summary of available experimental expansion anchor bolt test data is presented. These data were collected as part of programs by the nuclear industry to address generic issues related to verification of seismic adequacy of equipment in nuclear power plants. Some of the data presented are suitable for use in seismic probabilistic risk assessments. For example, mean values of ultimate strength, along with their standard deviation and coefficients of variation, for a range of most typical expansion anchor bolt sizes are presented. Effects of interaction between shear and tension, edge distance, spacing, and cracking of the concrete are presented in a manner that is more suitable for use in deterministic evaluations. Related industry programs to derive anchor bolt capacities are briefly discussed. Recommendations for areas of further investigation are also presented

Novel applications for glycosylphosphatidylinositol-anchored proteins in pharmaceutical and industrial biotechnology.

Science.gov (United States)

Müller, Günter

2011-04-01

Glycosylphosphatidylinositol (GPI)-anchored proteins have been regarded as typical cell surface proteins found in most eukaryotic cells from yeast to man. They are embedded in the outer plasma membrane leaflet via a carboxy-terminally linked complex glycolipid GPI structure. The amphiphilic nature of the GPI anchor, its compatibility with the function of the attached protein moiety and the capability of GPI-anchored proteins for spontaneous insertion into and transfer between artificial and cellular membranes initially suggested their potential for biotechnological applications. However, these expectations have been hardly fulfilled so far. Recent developments fuel novel hopes with regard to: (i) Automated online expression, extraction and purification of therapeutic proteins as GPI-anchored proteins based on their preferred accumulation in plasma membrane lipid rafts, (ii) multiplex custom-made protein chips based on GPI-anchored cell wall proteins in yeast, (iii) biomaterials and biosensors with films consisting of sets of distinct GPI-anchored binding-proteins or enzymes for sequential or combinatorial catalysis, and (iv) transport of therapeutic proteins across or into relevant tissue cells, e.g., enterocytes or adipocytes. Latter expectations are based on the demonstrated translocation of GPI-anchored proteins from plasma membrane lipid rafts to cytoplasmic lipid droplets and eventually further into microvesicles which upon release from donor cells transfer their GPI-anchored proteins to acceptor cells. The value of these technologies, which are all based on the interaction of GPI-anchored proteins with membranes and surfaces, for the engineering, production and targeted delivery of biomolecules for a huge variety of therapeutic and biotechnological purposes should become apparent in the near future.

Do anchor investors create value for initial public offerings? An empirical investigation

Directory of Open Access Journals (Sweden)

Seshadev Sahoo

2017-12-01

Full Text Available The concept of anchor investors was introduced by the market regulator, Securities Exchange Board of India (SEBI, to bring transparency in the book building mechanism. We examine anchor investors' investment in initial public offerings (IPOs to determine how they create value for issuing firms and participating investors. Using a database of 135 IPOs issued in the Indian market through book building mechanism during 2009–2014, we find that anchor investors' investment in IPOs reduces underpricing. Larger subscription from retail investors for anchor-supported IPOs indicates that anchor investors' participation is viewed as a credible attestation of quality of the issue. We document that anchor-supported IPOs are more liquid and less volatile in the short run. We also find that by controlling for other factors such as offer size, subscription rate and age of the firm, a part of the underpricing is reduced by anchor investors.

Considerations on the design of through-wall anchors

International Nuclear Information System (INIS)

Ricklefs, Ulf

2012-01-01

Connections to existing buildings are often the most difficult planning challenge for the realization of construction measures in case of piping system replacements in nuclear power plants. This is due to restricted space or limited load reserves of the building structure. Usually the realization of support connections to the existing buildings is achieved by anchor bolts. But in critical cases the preferred alternative solution uses through-wall anchors. Up to now uniform assessment thresholds are not available, no technical guidelines or regulations for construction variants exist. Through-wall anchors allow significantly higher load capacities for tensile and shear loads but require enhanced planning and realization efforts.

Anchor enhanced capsulorraphy in bunionectomies using an L-shaped capsulotomy.

Science.gov (United States)

Gould, John S; Ali, Sheriff; Fowler, Rachel; Fleisig, Glenn S

2003-01-01

The objective of this study was to investigate potential benefit of a suture anchor-enhanced capsulorraphy in the early maintenance of correction in bunionectomies. We compared, retrospectively, in successive series, the loss of correction of the Hallux Valgus (HV) and intermetatarsal (IM) angle, in those repaired with an L-shaped capsulorraphy enhanced with anchors to those without. Intraoperative and second week postoperative simulated weightbearing anterior posterior (AP) X-rays were used to evaluate results. By using only intraoperative and early postoperative X-rays, we should have effectively eliminated extraneous factors that might have influenced our results. A Total of 106 cases were investigated, 65 of which were repaired using anchors, the remaining 41 without. In the anchor group, 38 underwent a proximal metatarsal concentric shelf osteotomy (CSO)/modified McBride procedure, while the remaining 27 had a distal Chevron correction. In the without-anchor group, 21 had a CSO/modified McBride procedure while 20 underwent the Chevron procedure. In the without-anchor group, the average HV and IM loss of correction was 4.60 degrees (range, -2 to 21 degrees) and 0.6 degrees (range, -1 to 9 degrees) respectively. In the anchor group, the corresponding loss was 2.8 degrees (range, -3 to 17 degrees) and 0.6 degrees (range, -2 to 14 degrees) respectively. These results, when statistically analyzed, demonstrated that while the IM angle change was not statistically significant, the HV angle change was statistically significant, implying that the anchor plays a significant role in maintaining the surgical correction in both the distal Chevron and CSO/ modified McBride bunionectomies.

Stone anchors from the Okhamandal region, Gujarat Coast, India

Digital Repository Service at National Institute of Oceanography (India)

Sundaresh; Gaur, A.S.; Gudigar, P.; Tripati, S.; Vora, K.H.; Bandodkar, S.N.

During marine archaeological explorations since 1983, off Dwarka, a large number of stone anchors were discovered and dated to 1400 BC, comparing with anchors found in Mediterranean waters. In recent archaeological explorations off Dwarka, Bet...

Functionalized Nanostructures: Redox-Active Porphyrin Anchors for Supramolecular DNA Assemblies

KAUST Repository

Börjesson, Karl

2010-09-28

We have synthesized and studied a supramolecular system comprising a 39-mer DNA with porphyrin-modified thymidine nucleosides anchored to the surface of large unilamellar vesicles (liposomes). Liposome porphyrin binding characteristics, such as orientation, strength, homogeneity, and binding site size, was determined, suggesting that the porphyrin is well suited as a photophysical and redox-active lipid anchor, in comparison to the inert cholesterol anchor commonly used today. Furthermore, the binding characteristics and hybridization capabilities were studied as a function of anchor size and number of anchoring points, properties that are of importance for our future plans to use the addressability of these redox-active nodes in larger DNA-based nanoconstructs. Electron transfer from photoexcited porphyrin to a lipophilic benzoquinone residing in the lipid membrane was characterized by steady-state and time-resolved fluorescence and verified by femtosecond transient absorption. © 2010 American Chemical Society.

Operative treatment of acromioclavicular joint dislocation: a new technique with suture anchors

Directory of Open Access Journals (Sweden)

Zhang Jingwei

2014-07-01

Full Text Available 【Abstract】Objective: To evaluate clinical outcome of suture anchors in strengthening both acromioclavicular and coracoclavicular ligaments in the surgical treatment of acromioclavicular joint dislocation. Methods: Twenty-eight patients with acute traumatic Rockwood III, IV and V dislocations of the acromioclavicular joint surgically treated at our institute between October 2010 and January 2012 were recruited. All patients underwent open reduction combined with suture anchors. Function was evaluated using the ConstantMurley shoulder score. Clinical and radiographic shoulder ratings were evaluated using Taft criteria at 3, 6 and 12 months. Results:Two cases with fixation loosening were not included in final statistical analysis. Other patients obtained full joint reposition on immediate postoperative radiographs. Follow-up was performed with an average of 15.6 months (range, 12-19. After early range of motion exercises, 96.2% of the patients (25/26 could abduct and elevate their shoulders more than 90 degrees within postoperative 3 months. There was no infection. Average Constant-Murley score was 96.3 points (range, 94-100 and mean Taft shoulder rating was 10.7 points (range, 8-12 at 12 months. Conclusion: The suture anchor is a relatively simple technique and can avoid screw removal which is helpful in reconstructing both acromioclavicular and coracoclavicular ligaments in acute traumatic acromioclavicular joint dislocation. Key words: Acromioclavicular joint; Dislocations; Surgery; Suture anchors

Strength of bone tunnel versus suture anchor and push-lock construct in Broström repair.

Science.gov (United States)

Giza, Eric; Nathe, Ryan; Nathe, Tyler; Anderson, Matthew; Campanelli, Valentina

2012-06-01

Operative treatment of mechanical ankle instability is indicated for patients who have had multiple sprains and have continued episodes of instability despite bracing and rehabilitation. Anatomic reconstruction has been shown to have improved outcomes and return to sport as compared with nonanatomic reconstruction. The use of 2 suture anchors and a push-lock anchor is equal to 2 bone tunnels in strength to failure for anatomic Broström repair. Controlled laboratory study. In 7 matched pairs of human cadaver ankles, the calcaneofibular ligament (CFL) and anterior talofibular ligament (ATFL) were incised from their origin on the fibula. A No. 2 Fiberwire suture was placed into the CFL and a separate suture into the ATFL in a running Krackow fashion with a total of 4 locking loops. In 1 ankle of the matched pair, the ligaments were repaired to their anatomic insertion with bone tunnels. In the other, 2 suture anchors were used to reattach the ligaments to their anatomic origins, and a push-lock was used proximally to reinforce these suture anchors. The ligaments were cyclically loaded 20 times and then tested to failure. Torque to failure, degrees to failure, and stiffness were measured. The authors performed a matched pair analysis. An a priori power analysis of 0.8 demonstrated 6 pairs were needed to show a difference of 30% with a 15% standard error at a significance level of .05. There was no difference in the degrees to failure, torque to failure, and stiffness. A post hoc power analysis of torque to failure showed a power of .89 with 7 samples. Power for initial stiffness was .97 with 7 samples. Eleven of 14 specimens failed at either the suture anchor or the bone tunnel. There is no statistical difference in strength or stiffness for a suture anchor and push-lock construct as compared with a bone tunnel construct for an anatomic repair of the lateral ligaments of the ankle. The use of suture anchors in lateral ligament stabilization allows for a smaller

Ru-bis(pyridine)pyrazolate (bpp)-Based Water-Oxidation Catalysts Anchored on TiO2: The Importance of the Nature and Position of the Anchoring Group.

Science.gov (United States)

Francàs, Laia; Richmond, Craig; Garrido-Barros, Pablo; Planas, Nora; Roeser, Stephan; Benet-Buchholz, Jordi; Escriche, Lluís; Sala, Xavier; Llobet, Antoni

2016-04-04

Three distinct functionalisation strategies have been applied to the in,in-[{Ru(II)(trpy)}2(μ-bpp)(H2O)2](3+) (trpy=2,2':6',2''-terpyridine, bpp=bis(pyridine)pyrazolate) water-oxidation catalyst framework to form new derivatives that can adsorb onto titania substrates. Modifications included the addition of sulfonate, carboxylate, and phosphonate anchoring groups to the terpyridine and bis(pyridyl)pyrazolate ligands. The complexes were characterised in solution by using 1D NMR, 2D NMR, and UV/Vis spectroscopic analysis and electrochemical techniques. The complexes were then anchored on TiO2-coated fluorinated tin oxide (FTO) films, and the reactivity of these new materials as water-oxidation catalysts was tested electrochemically through controlled-potential electrolysis (CPE) with oxygen evolution detected by headspace analysis with a Clark electrode. The results obtained highlight the importance of the catalyst orientation with respect to the titania surface in regard to its capacity to catalytically oxidize water to dioxygen. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Coupled thermo-fluid stress analysis of Kambara Reactor with various anchors in the stirring of molten iron at extremely high temperatures

International Nuclear Information System (INIS)

Huang, De-Shau; Huang, Feng-Chi

2014-01-01

Kambara Reactors (KR) are commonly used to reduce sulfur content in steel making, achieving efficiency levels exceeding 85% at 1300 °C. Unfortunately, the operational lifespan of the KR impeller is somewhat limited due to fracturing of the refractory material via thermal shock, resulting in the penetration of molten iron into the inner core. Few studies have investigated the coupled thermo-fluid stress of KR impellers at extremely high temperatures. This study employed CFX and FEM to simulate and analyze the molten iron and the resulting thermal stress imposed on the KR impeller. Simulation results including flow field, temperature, and thermal stress under extremely high temperatures are in strong agreement with empirical data. V-type anchors for the KR impeller outperformed Y-type anchors. - Highlights: • A thermo-fluid coupling approach is proposed to analyze the thermal stress. • The temperature and stress of the impeller are 790 °C and 744 MPa at the final stage. • The highest temperatures occur at the tip of anchors, which causes material crack. • The thermal stress in impellers with Y-type anchors is greater than V-type anchors

Electrical properties and mechanical stability of anchoring groups for single-molecule electronics

Directory of Open Access Journals (Sweden)

Riccardo Frisenda

2015-07-01

Full Text Available We report on an experimental investigation of transport through single molecules, trapped between two gold nano-electrodes fabricated with the mechanically controlled break junction (MCBJ technique. The four molecules studied share the same core structure, namely oligo(phenylene ethynylene (OPE3, while having different aurophilic anchoring groups: thiol (SAc, methyl sulfide (SMe, pyridyl (Py and amine (NH2. The focus of this paper is on the combined characterization of the electrical and mechanical properties determined by the anchoring groups. From conductance histograms we find that thiol anchored molecules provide the highest conductance; a single-level model fit to current–voltage characteristics suggests that SAc groups exhibit a higher electronic coupling to the electrodes, together with better level alignment than the other three groups. An analysis of the mechanical stability, recording the lifetime in a self-breaking method, shows that Py and SAc yield the most stable junctions while SMe form short-lived junctions. Density functional theory combined with non-equlibrium Green’s function calculations help in elucidating the experimental findings.

Empirical evidence for resource-rational anchoring and adjustment.

Science.gov (United States)

Lieder, Falk; Griffiths, Thomas L; M Huys, Quentin J; Goodman, Noah D

2018-04-01

People's estimates of numerical quantities are systematically biased towards their initial guess. This anchoring bias is usually interpreted as sign of human irrationality, but it has recently been suggested that the anchoring bias instead results from people's rational use of their finite time and limited cognitive resources. If this were true, then adjustment should decrease with the relative cost of time. To test this hypothesis, we designed a new numerical estimation paradigm that controls people's knowledge and varies the cost of time and error independently while allowing people to invest as much or as little time and effort into refining their estimate as they wish. Two experiments confirmed the prediction that adjustment decreases with time cost but increases with error cost regardless of whether the anchor was self-generated or provided. These results support the hypothesis that people rationally adapt their number of adjustments to achieve a near-optimal speed-accuracy tradeoff. This suggests that the anchoring bias might be a signature of the rational use of finite time and limited cognitive resources rather than a sign of human irrationality.

Thermal anchoring of wires in large scale superconducting coil test experiment

International Nuclear Information System (INIS)

Patel, Dipak; Sharma, A.N.; Prasad, Upendra; Khristi, Yohan; Varmora, Pankaj; Doshi, Kalpesh; Pradhan, S.

2013-01-01

Highlights: • We addressed how thermal anchoring in large scale coil test is different compare to small cryogenic apparatus? • We did precise estimation of thermal anchoring length at 77 K and 4.2 K heat sink in large scale superconducting coil test experiment. • We addressed, the quality of anchoring without covering entire wires using Kapton/Teflon tape. • We obtained excellent results in temperature measurement without using GE Varnish by doubling estimated anchoring length. -- Abstract: Effective and precise thermal anchoring of wires in cryogenic experiment is mandatory to measure temperature in milikelvin accuracy and to avoid unnecessary cooling power due to additional heat conduction from room temperature (RT) to operating temperature (OT) through potential, field, displacement and stress measurement instrumentation wires. Instrumentation wires used in large scale superconducting coil test experiments are different compare to cryogenic apparatus in terms of unique construction and overall diameter/area due to errorless measurement in large time-varying magnetic field compare to small cryogenic apparatus, often shielded wires are used. Hence, along with other variables, anchoring techniques and required thermal anchoring length are entirely different in this experiment compare to cryogenic apparatus. In present paper, estimation of thermal anchoring length of five different types of instrumentation wires used in coils test campaign at Institute for Plasma Research (IPR), India has been discussed and some temperature measurement results of coils test campaign have been presented

Results of the ANCHOR prospective, multicenter registry of EndoAnchors for type Ia endoleaks and endograft migration in patients with challenging anatomy.

Science.gov (United States)

Jordan, William D; Mehta, Manish; Varnagy, David; Moore, William M; Arko, Frank R; Joye, James; Ouriel, Kenneth; de Vries, Jean-Paul

2014-10-01

Proximal attachment site complications continue to occur after endovascular repair of abdominal aortic aneurysms (EVAR), specifically type Ia endoleak and endograft migration. EndoAnchors (Aptus Endosystems, Sunnyvale, Calif) were designed to enhance endograft proximal fixation and sealing, and the current study was undertaken to evaluate the potential benefit of this treatment. During the 23-month period ending in December 2013, 319 subjects were enrolled at 43 sites in the United States and Europe. EndoAnchors were implanted in 242 patients (75.9%) at the time of an initial EVAR procedure (primary arm) and in 77 patients with an existing endograft and proximal aortic neck complications (revision arm). Technical success was defined as deployment of the desired number of EndoAnchors, adequate penetration of the vessel wall, and absence of EndoAnchor fracture. Procedural success was defined as technical success without a type Ia endoleak at completion angiography. Values are expressed as mean ± standard deviation and interquartile range. The 238 male (74.6%) and 81 female (25.4%) subjects had a mean age of 74.1 ± 8.2 years. Aneurysms averaged 58 ± 13 (51-63) mm in diameter at the time of EndoAnchor implantation (core laboratory measurements). The proximal aortic neck averaged 16 ± 13 (7-23) mm in length (42.7% <10 mm and 42.7% conical) and 27 ± 4 mm (25-30 mm) in diameter; infrarenal neck angulation was 24 ± 15 (13-34) degrees. The number of EndoAnchors deployed was 5.8 ± 2.1 (4-7). Technical success was achieved in 303 patients (95.0%) and procedural success in 279 patients (87.5%), 217 of 240 (89.7%) and 62 of 77 (80.5%) in the primary and revision arms, respectively. There were 29 residual type Ia endoleaks (9.1%) at the end of the procedure. During mean follow-up of 9.3 ± 4.7 months, 301 patients (94.4%) were free from secondary procedures. Among the 18 secondary procedures, eight were performed for residual type Ia endoleaks and the others

PSA-2, Stress Analysis, Thermal Expansion and Loads in Multi Anchor Piping System

Energy Technology Data Exchange (ETDEWEB)

Nickols, A N [Codes Coordinator, Atomics International, P. O. Box 309, Canoga Park, California 91304 (United States)

1975-03-01

1 - Description of problem or function: PSA2 computes the reactions and stresses caused by thermal expansion and loads in a multi-anchor piping system which may contain loops and may be partially restrained at any point in any direction. 2 - Method of solution: The linear equations for the statically indeterminate pipe system are set up by a generalization of Brock's matrix method. By a systematic use of linear transforms, the matrix of the system of linear equations can be obtained by incidence algebra in the form of a symmetric banded matrix. 2 - Restrictions on the complexity of the problem - Maximum of: 36 sections. 3 - Unusual features of the program - PSA2 takes into account: (a) elasticity of the attachment of the pipe to the foundation, (b) restraints on pipe displacements by anchors and intermediate partial constraints of linear type, (c) given constant forces and moments acting upon the pipe system, (d) thermal expansion, (e) any geometrical structure of the pipe system, (f) several cases of stressing per pipe system, and (g) both metric and English units.

PSA-2, Stress Analysis, Thermal Expansion and Loads in Multi Anchor Piping System

International Nuclear Information System (INIS)

Nickols, A.N.

1975-01-01

1 - Description of problem or function: PSA2 computes the reactions and stresses caused by thermal expansion and loads in a multi-anchor piping system which may contain loops and may be partially restrained at any point in any direction. 2 - Method of solution: The linear equations for the statically indeterminate pipe system are set up by a generalization of Brock's matrix method. By a systematic use of linear transforms, the matrix of the system of linear equations can be obtained by incidence algebra in the form of a symmetric banded matrix. 2 - Restrictions on the complexity of the problem - Maximum of: 36 sections. 3 - Unusual features of the program - PSA2 takes into account: (a) elasticity of the attachment of the pipe to the foundation, (b) restraints on pipe displacements by anchors and intermediate partial constraints of linear type, (c) given constant forces and moments acting upon the pipe system, (d) thermal expansion, (e) any geometrical structure of the pipe system, (f) several cases of stressing per pipe system, and (g) both metric and English units

Differences regarding job satisfaction and job involvement of psychologists with different dominant career anchors.

Science.gov (United States)

Bester, C L; Mouton, T

2006-08-01

In order to contribute to higher levels of job satisfaction, job involvement and productivity, a match or fit should be established between the dominant career anchor associated with a specific occupation and that of the employee. A career anchor is an individual's set of self-perceived talents, abilities, motives, needs and values that form the nucleus of one's occupational self-concept. Psychologists have always been part of the service orientated careers and therefore one would expect that it is likely that their dominant career anchor would be service orientation. If this is the case, psychologists with service as their dominant career anchor are supposed to have greater job satisfaction and job involvement compared to those with different career anchors. However, according to literature, this assumption is not necessarily correct. The primary goals of the current study were to determine whether in fact service is the dominant career anchor of psychologists in the Free State and whether there are significant differences regarding job satisfaction and job involvement between psychologists with and without service as their dominant career anchor. A third goal was to determine whether psychologists with different dominant career anchors differ significantly from one another regarding job satisfaction and job involvement. Questionnaires measuring career orientations, job satisfaction and job involvement were sent to 165 of the 171 registered psychologists in the Free State region. Only 75 psychologists (45,5%) responded which exceeded the traditional return rate of 20 to 30%. Due to the small sample of respondents, a nonparametric statistical test, namely the Mann Whitney U test was conducted to determine possible differences. An analysis of the data showed that 21 respondents had entrepreneurship as their dominant career orientation while 12 fell in the technical/functional, 12 in the challenging, 9 in the service and 8 in the autonomy categories of dominant

Lifestyle integration-gender based stereotypes: a study on Schein‟s career anchors within an ODeL HEI

Directory of Open Access Journals (Sweden)

Marili Williams

2014-01-01

Full Text Available This article is based on research that examined the differences between the aspirations of females and males in the workplace in terms of Schein‟s career anchors and enablers. The stereotype that females only work to ensure enhanced family lifestyles remains evident in the daily life of all (Hoobler, Lemmon & Wyane, 2014, p. 704; Mihail, 2006. Furthermore the stereotype that males‟ focus is much more ambitious in terms of reaching the highest managerial achievement/technical/ functional competence is regarded as a reality within society (Hoobler, Lemmon & Wyane, 2014, p. 704; Mihail, 2006. Insight into the question whether females work to live or live to work was investigated and this article reports on the differences between females and males regarding their work life ambitions. The data resulted from a quantitative research approach and the population consisted of 4 200 employees within an Open Distance electronic Learning (ODeL Higher Education Institution (HEI in South Africa. The focus was on the composition of a structured career conversation framework, using the original Schein career anchors (Schein, 1978; 1990; 1996 and the three-factor career-enabler model, developed by Grobler, Bezuidenhout and Rudolph (2014. Descriptive statistics, chi-square statistics as well as independent t-test analysis was used to identify the differences between genders with regard to career anchors and career enablers in different career stages. The results of the analysis illustrated that females focus more on the autonomy/independence- and lifestyle integration career anchors than males in the first 3 years of employment, thereafter their focus remains more on the lifestyle integration career anchor than males. Males however focus more on the general managerial career anchor in the first 3 years of their careers than women; and after 3 years males‟ focus moves more to the entrepreneurial creativity career anchor. The reported differences between

Cyclic biomechanical testing of biocomposite lateral row knotless anchors in a human cadaveric model.

Science.gov (United States)

Barber, F Alan; Bava, Eric D; Spenciner, David B; Piccirillo, Justin

2013-06-01

The purpose of this study was to assess the mechanical performance of biocomposite knotless lateral row anchors based on both anchor design and the direction of pull. Two lateral row greater tuberosity insertion sites (anterior and posterior) were identified in matched pairs of fresh-frozen human cadaveric shoulders DEXA (dual energy X-ray absorptiometry) scanned to verify comparability. The humeri were stripped of all soft tissue and 3 different biocomposite knotless lateral row anchors: HEALIX Knotless BR (DePuy Mitek, Raynham MA), BioComposite PushLock (Arthrex, Naples, FL), and Bio-SwiveLock (Arthrex). Fifty-two anchors were distributed among the insertion locations and tested them with either an anatomic or axial pull. A fixed-gauge loop (15 mm) of 2 high-strength sutures from each anchor was created. After a 10-Nm preload, anchors were cycled from 10 to 45 Nm at 0.5 Hz for 200 cycles and tested to failure at 4.23 mm/second. The load to reach 3 mm and 5 mm displacement, ultimate failure load, displacement at ultimate failure, and failure mode were recorded. Threaded anchors (Bio-SwiveLock, P = .03; HEALIX Knotless, P = .014) showed less displacement with anatomic testing than did the nonthreaded anchor (BioComposite PushLock), and the HEALIX Knotless showed less overall displacement than did the other 2 anchors. The Bio-SwiveLock exhibited greater failure loads than did the other 2 anchors (P < .05). Comparison of axial and anatomic loading showed no maximum load differences for all anchors as a whole (P = .1084). Yet, anatomic pulling produced higher failure loads than did axial pulling for the Bio-SwiveLock but not for the BioComposite PushLock or the HEALIX Knotless. The nonthreaded anchor (BioComposite PushLock) displayed lower failure loads than did both threaded anchors with axial pulling. Threaded biocomposite anchors (HEALIX Knotless BR and Bio-SwiveLock) show less anatomic loading displacement and higher axial failure loads than do the nonthreaded

The anchors of steel wire ropes, testing methods and their results

Directory of Open Access Journals (Sweden)

J. Krešák

2012-10-01

Full Text Available The present paper introduces an application of the acoustic and thermographic method in the defectoscopic testing of immobile steel wire ropes at the most critical point, the anchor. First measurements and their results by these new defectoscopic methods are shown. In defectoscopic tests at the anchor, the widely used magnetic method gives unreliable results, and therefore presents a problem for steel wire defectoscopy. Application of the two new methods in the steel wire defectoscopy at the anchor point will enable increased safety measures at the anchor of steel wire ropes in bridge, roof, tower and aerial cable lift constructions.

Failure Capacity Evaluation for Anchor System of NPP Facilities by using a Shaking Table Test

International Nuclear Information System (INIS)

Kwon, Hyung O; Jung, Min Ki; Park, Jin Wan; Lim, Ji Hoon

2010-02-01

This study investigate the destructive influence of crack locations on the anchor performance to evaluate the seismic performance of NPP equipment anchored on damaged concrete. For this purpose, small-scale specimens were fabricated according to the following three cases: 1) with a non-damaged anchor; 2) with cracks running through the anchor; and 3) with cracks along the expected corn-shape fracture away from the anchor. The result verified with the finite element method is as follows: In the first and second cases that is, with a non-damaged anchor and with cracks running through the anchor destruction occurred at the anchor steel. In the third case that is, with cracks around the anchor, a 30% decline in the seismic performance was identified. This result indicates that evaluation of seismic performance and relevant reinforcement are required when cracks occur away from the anchor along the expected destructive surface

Anchored but not internalized: shape dependent endocytosis of nanodiamond

Science.gov (United States)

Zhang, Bokai; Feng, Xi; Yin, Hang; Ge, Zhenpeng; Wang, Yanhuan; Chu, Zhiqin; Raabova, Helena; Vavra, Jan; Cigler, Petr; Liu, Renbao; Wang, Yi; Li, Quan

2017-04-01

Nanoparticle-cell interactions begin with the cellular uptake of the nanoparticles, a process that eventually determines their cellular fate. In the present work, we show that the morphological features of nanodiamonds (NDs) affect both the anchoring and internalization stages of their endocytosis. While a prickly ND (with sharp edges/corners) has no trouble of anchoring onto the plasma membrane, it suffers from difficult internalization afterwards. In comparison, the internalization of a round ND (obtained by selective etching of the prickly ND) is not limited by its lower anchoring amount and presents a much higher endocytosis amount. Molecular dynamics simulation and continuum modelling results suggest that the observed difference in the anchoring of round and prickly NDs likely results from the reduced contact surface area with the cell membrane of the former, while the energy penalty associated with membrane curvature generation, which is lower for a round ND, may explain its higher probability of the subsequent internalization.

Fixation of a human rib by an intramedullary telescoping splint anchored by bone cement.

Science.gov (United States)

Liovic, Petar; Šutalo, Ilija D; Marasco, Silvana F

2016-09-01

A novel concept for rib fixation is presented that involves the use of a bioresorbable polymer intramedullary telescoping splint. Bone cement is used to anchor each end of the splint inside the medullary canal on each side of the fracture site. In this manner, rib fixation is achieved without fixation device protrusion from the rib, making the splint completely intramedullary. Finite element analysis is used to demonstrate that such a splint/cement composite can preserve rib fixation subjected to cough-intensity force loadings. Computational fluid dynamics and porcine rib experiments were used to study the anchor formation process required to complete the fixation.

The anchor of the frameless intrauterine device does not migrate over time: an analysis in over 300 women

Directory of Open Access Journals (Sweden)

Wildemeersch D

2014-12-01

Full Text Available Dirk Wildemeersch,1 Ansgar Pett,2 Sohela Jandi,2 Kilian Nolte,3 Wolfgang Albrecht4 1Gynecological Outpatient Clinic and IUD Training Centre, Ghent, Belgium; 2Gynecological Outpatient Clinic, Berlin, Germany; 3Gynecological Outpatient Clinic, Uetze, Germany; 4Gynecological Outpatient Clinic, Feldkirchen, Austria Objective: To evaluate the correct position of the anchor at insertion and follow-up and assess if migration of the anchor occurs over time. Materials and methods: This was an insertion-related, prospective, postmarketing study in 309 women. Following insertion, women were followed up at 4–6 weeks, 6 months, and yearly thereafter. The position of the visualized anchor in the fundus of the uterus was evaluated using ultrasound by measuring its distance from the serosal surface of the uterus (SA-distance. Results: A total of 309 parous (n=115 and nulliparous (n=194 women were fitted with the frameless GyneFix 200 or the GyneFix 330 intrauterine device for contraception. The mean SA-distance in 306 parous and nulliparous women was 6.0 mm (range 2.0–24.0 mm at insertion in the parous group and 5.4 mm (range 1.3–11.0 mm in the nulliparous group. At the first follow-up in 281 women, the SA-distance was 6.0 mm (range 2.0–12.0 mm in the parous group and 5.5 mm (range 1.1–11.0 mm in the nulliparous group. The SA-distance was not significantly different. One patient had an exceptionally large SA-distance of 24 mm, probably due to insertion in the posterior wall. No follow-up could be done in this patient. In 77 women, the SA-distance was measured up to 42 months. The mean SA-distance at insertion in the parous group was 5.2 mm (range 3.0–8.5 mm and 4.8 mm (range 1.3–7.0 mm in the nulliparous group. At the last follow-up up to 36 months or longer, the SA-distance was 5.1 mm (range 3.0–8.5 mm in the parous group and 4.9 mm (range 1.3–7.0 mm in the nulliparous group. The SA-distance was not significantly different. The visualized

Arrows as Anchors: An Analysis of the Material Features of Electric Field Vector Arrows

Science.gov (United States)

Gire, Elizabeth; Price, Edward

2014-01-01

Representations in physics possess both physical and conceptual aspects that are fundamentally intertwined and can interact to support or hinder sense making and computation. We use distributed cognition and the theory of conceptual blending with material anchors to interpret the roles of conceptual and material features of representations in…

Plant glycosylphosphatidylinositol (GPI) anchored proteins at the plasma membrane-cell wall nexus.

Science.gov (United States)

Yeats, Trevor H; Bacic, Antony; Johnson, Kim L

2018-04-18

Approximately 1% of plant proteins are predicted to be post-translationally modified with a glycosylphosphatidylinositol (GPI) anchor that tethers the polypeptide to the outer leaflet of the plasma membrane. While the synthesis and structure of GPI anchors is largely conserved across eukaryotes, the repertoire of functional domains present in the GPI-anchored proteome has diverged substantially. In plants, this includes a large fraction of the GPI-anchored proteome being further modified with plant-specific arabinogalactan (AG) O-glycans. The importance of the GPI-anchored proteome to plant development is underscored by the fact that GPI biosynthetic null mutants exhibit embryo lethality. Mutations in genes encoding specific GPI-anchored proteins (GAPs) further supports their contribution to diverse biological processes occurring at the interface of the plasma membrane and cell wall, including signaling, cell wall metabolism, cell wall polymer cross-linking, and plasmodesmatal transport. Here, we review the literature concerning plant GPI-anchored proteins in the context of their potential to act as molecular hubs that mediate interactions between the plasma membrane and the cell wall and their potential to transduce the signal into the protoplast and thereby activate signal transduction pathways. This article is protected by copyright. All rights reserved.

The Naturalized Nation: Anchoring, Objectification and Naturalized Social Representations of History

Directory of Open Access Journals (Sweden)

Eemeli Hakoköngäs

2016-12-01

Full Text Available This study focuses on the connection between social representations of history and collective memory from the perspective of elementary concepts of social representations theory: anchoring, objectification and naturalization. The aims of the study are to arrive at a conceptual clarity of this connection and demonstrate how to apply basic concepts of social representations theory to the study of collective memory. The study also focuses on the naturalized characteristics of Finnish history. The data consist of the covers of twenty Finnish history books between the years 1965 and 2014. All the covers are embellished with typography or visual images. The covers were analysed using a semiotic approach in which the interest is in the description (denotation, the associations (connotation and the meaning system these construe (myth. The analysis shows how national history is concretized with visual images (objectification, how the meaning of representation is conveyed (anchoring and how collective memory is maintained (naturalization, transmitted and shaped during the years. The results show how the stable collective memories and changing social representations of history are interacting. The most frequently used visual element was the colour blue, which alludes to the Finnish flag, a symbol of the nation that represents the core of Finnish history. The study suggests that it is possible to conceptualize collective memories as naturalized social representations of history. It shows how processes of anchoring and objectification serve as tools of collective memory and how the naturalized conceptions are subtly changed. In addition, the study develops the use of visual semiotic analysis in social representations research.

High-resolution structure of TBP with TAF1 reveals anchoring patterns in transcriptional regulation.

Science.gov (United States)

Anandapadamanaban, Madhanagopal; Andresen, Cecilia; Helander, Sara; Ohyama, Yoshifumi; Siponen, Marina I; Lundström, Patrik; Kokubo, Tetsuro; Ikura, Mitsuhiko; Moche, Martin; Sunnerhagen, Maria

2013-08-01

The general transcription factor TFIID provides a regulatory platform for transcription initiation. Here we present the crystal structure (1.97 Å) and NMR analysis of yeast TAF1 N-terminal domains TAND1 and TAND2 bound to yeast TBP, together with mutational data. We find that yeast TAF1-TAND1, which in itself acts as a transcriptional activator, binds TBP's concave DNA-binding surface by presenting similar anchor residues to TBP as does Mot1 but from a distinct structural scaffold. Furthermore, we show how TAF1-TAND2 uses an aromatic and acidic anchoring pattern to bind a conserved TBP surface groove traversing the basic helix region, and we find highly similar TBP-binding motifs also presented by the structurally distinct TFIIA, Mot1 and Brf1 proteins. Our identification of these anchoring patterns, which can be easily disrupted or enhanced, provides insight into the competitive multiprotein TBP interplay critical to transcriptional regulation.

Unintended anchors: Building rating systems and energy performance goals for U.S. buildings

International Nuclear Information System (INIS)

Klotz, Leidy; Mack, Daniel; Klapthor, Brent; Tunstall, Casey; Harrison, Jennilee

2010-01-01

In the U.S., where buildings account for 40% of energy use, commercial buildings use more energy per unit area than ever before. However, exemplary buildings demonstrate the feasibility of much better energy performance at no additional first cost. This research examines one possible explanation for this inconsistency. The aim is to investigate whether the anchoring bias, which refers to our tendency to gravitate towards a pre-defined standard regardless of its relevance, influences energy performance goals in building design. The scope examines professionals who help set energy performance goals for U.S. buildings. Prior to being asked to set an energy performance goal, these professionals were randomly directed to one of three series of questions. One series set an anchor of 90% energy reduction beyond standard practice, one set a 30% anchor, and one set no anchor. Respondents exposed to the 90% anchor, and respondents exposed to no anchor at all, set higher energy performance goals than respondents exposed to the 30% anchor. These results suggest that building rating systems that only reward incremental energy improvements may inadvertently create anchors, thereby discouraging more advanced energy performance goals and inhibiting energy performance that is technically and economically feasible.

Anchor stabilization of trapped particle modes in mirror machines

International Nuclear Information System (INIS)

Berk, H.L.; Roslyakov, G.V.

1986-07-01

It is shown that for trapped particle modes in tandem mirrors, the pressure of the passing particles in the anchor region introduces a stabilizing term proportional to the sum of the anchor's field line curvature and total diamagnetic pressure. The theory is applied to the proposed gas dynamic trap experiment

Anchor stabilization of trapped particle modes in mirror machines

International Nuclear Information System (INIS)

Berk, H.L.; Roslyakov, G.V.

1986-04-01

It is shown that for trapped particle modes in tandem mirrors, the pressure of the passing particles in the anchor region introduces a stabilizing term proportional to the sum of the anchor's field line curvature and total diamagnetic pressure. The theory is applied to the proposed gas dynamic trap experiment

Modality analysis of anchored ion exchange tower using Ansys

International Nuclear Information System (INIS)

Li Liang; Lei Zeyong

2008-01-01

Ion exchange towers are exposed to serious damage in the event of earthquakes. It is very necessary to study the seismic resistance of ion exchange tower. A finite element model of anchored ion exchange tower was made by Ansys. The first 10 ranks of inherent frequencies were made out, and three-dimensional main vibratory model figures were drawn out. The maximal stress along x-axis and y-axis and the main displacement were found at the bottom part of the wall of tower junction with the pillars. It is concluded that the breakage of tower wall easily occurs at the bottom part of the wall of tower junction with the pillars. Therefore, it is very important to reinforce the junction of the tower body, and the strengthening plate should lie near the bottom of wall. (authors)

Differences regarding job satisfaction and job involvement of psychologists with different dominant career anchors

Directory of Open Access Journals (Sweden)

CL Bester

2006-09-01

Full Text Available In order to contribute to higher levels of job satisfaction, job involvement , and productivity, a match or fit should be established between the dominant career anchor associated with a specific occupation and that of the employee. A career anchor is an individual’s set of self-perceived talents, abilities, motives, needs and values that form the nucleus of one’s occupational self-concept. Psychologists have always been part of the service orientated careers and therefore one would expect that it is likely that their dominant career anchor would be service orientation. If this is the case, psychologists with service as their dominant career anchor are supposed to have greater job satisfaction and job involvement compared to those with different career anchors. However, according to literature, this assumption is not necessarily correct. The primary goals of the current study were to determine whether in fact service is the dominant career anchor of psychologists in the Free State and whether there are significant differences regarding job satisfaction and job involvement between psychologists with and without service as their dominant career anchor. A third goal was to determine whether psychologists with different dominant career anchors differ significantly from one another regarding job satisfaction and job involvement. Questionnaires measuring career orientations, job satisfaction and job involvement were sent to 165 of the 171 registered psychologists in the Free State region. Only 75 psychologists (45,5% responded which exceeded the traditional return rate of 20 to 30%. Due to the small sample of respondents, a nonparametric statistical test, namely the Mann Whitney U test was conducted to determine possible differences. An analysis of the data showed that 21 respondents had entrepreneurship as their dominant career orientation while 12 fell in the technical/functional, 12 in the challenging, 9 in the service and 8 in the autonomy

Anchoring novel molecular biomarker responses to traditional responses in fish exposed to environmental contamination

International Nuclear Information System (INIS)

Nogueira, Patricia; Pacheco, Mario; Lourdes Pereira, M.; Mendo, Sonia; Rotchell, Jeanette M.

2010-01-01

The responses of Dicentrarchus labrax and Liza aurata to aquatic pollution were assessed in a contaminated coastal lagoon, using both traditional and novel biomarkers combined. DNA damage, assessed by comet assay, was higher in both fish species from the contaminated sites, whereas levels of cytochrome P450 1A1 gene expression were not significantly altered. The liver histopathological analysis also revealed significant lesions in fish from contaminated sites. Alterations in ras and xpf genes were analysed and additional pollutant-responsive genes were identified. While no alterations were found in ras gene, a downregulation of xpf gene was observed in D. labrax from a contaminated site. Suppression subtractive hybridization applied to D. labrax collected at a contaminated site, revealed altered expression in genes involved in energy metabolism, immune system activity and antioxidant response. The approach and results reported herein demonstrate the utility of anchoring traditional biomarker responses alongside novel biomarker responses. - Novel molecular biomarkers of aquatic environmental contamination in fish.

Functionalized Nanostructures: Redox-Active Porphyrin Anchors for Supramolecular DNA Assemblies

KAUST Repository

Börjesson, Karl; Wiberg, Joanna; El-Sagheer, Afaf H.; Ljungdahl, Thomas; Må rtensson, Jerker; Brown, Tom; Nordén, Bengt; Albinsson, Bo

2010-01-01

, such as orientation, strength, homogeneity, and binding site size, was determined, suggesting that the porphyrin is well suited as a photophysical and redox-active lipid anchor, in comparison to the inert cholesterol anchor commonly used today. Furthermore

Steel shear strength of anchors with stand-off base plates.

Science.gov (United States)

2013-09-01

Sign and signal structures are often connected to concrete foundations through a stand-off annular base plate with a double-nut anchor bolt connection, which leaves exposed anchor bolt lengths below leveling nuts used in these connections. Cantilever...

Biomechanical advantages of triple-loaded suture anchors compared with double-row rotator cuff repairs.

Science.gov (United States)

Barber, F Alan; Herbert, Morley A; Schroeder, F Alexander; Aziz-Jacobo, Jorge; Mays, Matthew M; Rapley, Jay H

2010-03-01

To evaluate the strength and suture-tendon interface security of various suture anchors triply and doubly loaded with ultrahigh-molecular weight polyethylene-containing sutures and to evaluate the relative effectiveness of placing these anchors in a single-row or double-row arrangement by cyclic loading and then destructive testing. The infraspinatus muscle was reattached to the original humeral footprint by use of 1 of 5 different repair patterns in 40 bovine shoulders. Two single-row repairs and three double-row repairs were tested. High-strength sutures were used for all repairs. Five groups were studied: group 1, 2 triple-loaded screw suture anchors in a single row with simple stitches; group 2, 2 triple-loaded screw anchors in a single row with simple stitches over a fourth suture passed perpendicularly ("rip-stop" stitch); group 3, 2 medial and 2 lateral screw anchors with a single vertical mattress stitch passed from the medial anchors and 2 simple stitches passed from the lateral anchors; group 4, 2 medial double-loaded screw anchors tied in 2 mattress stitches and 2 push-in lateral anchors capturing the medial sutures in a "crisscross" spanning stitch; and group 5, 2 medial double-loaded screw anchors tied in 2 mattress stitches and 2 push-in lateral anchors creating a "suture-bridge" stitch. The specimens were cycled between 10 and 180 N at 1.0 Hz for 3,500 cycles or until failure. Endpoints were cyclic loading displacement (5 and 10 mm), total displacement, and ultimate failure load. A single row of triply loaded anchors was more resistant to stretching to a 5- and 10-mm gap than the double-row repairs with or without the addition of a rip-stop suture (P row repair (P row created by 2 medial double-loaded suture anchors and 2 lateral push-in anchors stretched more than any other group (P row repairs with either crossing sutures or 4 separate anchor points were more likely to fail (5- or 10-mm gap) than a single-row repair loaded with 3 simple sutures

High-Performance Modeling and Simulation of Anchoring in Granular Media for NEO Applications

Science.gov (United States)

Quadrelli, Marco B.; Jain, Abhinandan; Negrut, Dan; Mazhar, Hammad

2012-01-01

NASA is interested in designing a spacecraft capable of visiting a near-Earth object (NEO), performing experiments, and then returning safely. Certain periods of this mission would require the spacecraft to remain stationary relative to the NEO, in an environment characterized by very low gravity levels; such situations require an anchoring mechanism that is compact, easy to deploy, and upon mission completion, easy to remove. The design philosophy used in this task relies on the simulation capability of a high-performance multibody dynamics physics engine. On Earth, it is difficult to create low-gravity conditions, and testing in low-gravity environments, whether artificial or in space, can be costly and very difficult to achieve. Through simulation, the effect of gravity can be controlled with great accuracy, making it ideally suited to analyze the problem at hand. Using Chrono::Engine, a simulation pack age capable of utilizing massively parallel Graphic Processing Unit (GPU) hardware, several validation experiments were performed. Modeling of the regolith interaction has been carried out, after which the anchor penetration tests were performed and analyzed. The regolith was modeled by a granular medium composed of very large numbers of convex three-dimensional rigid bodies, subject to microgravity levels and interacting with each other with contact, friction, and cohesional forces. The multibody dynamics simulation approach used for simulating anchors penetrating a soil uses a differential variational inequality (DVI) methodology to solve the contact problem posed as a linear complementarity method (LCP). Implemented within a GPU processing environment, collision detection is greatly accelerated compared to traditional CPU (central processing unit)- based collision detection. Hence, systems of millions of particles interacting with complex dynamic systems can be efficiently analyzed, and design recommendations can be made in a much shorter time. The figure

Management of subluxated capsular bag-fixated intraocular lenses using a capsular anchor

NARCIS (Netherlands)

Ton, Yokrat; Naftali, Modi; Lapid Gortzak, Ruth; Assia, Ehud I.

2016-01-01

We describe the use of the capsular anchor (AssiAnchor) to manage a subluxated intraocular lens (IOL) in the capsular bag. The anchor comprises 2 prongs that hold the anterior lens capsule and a central rod that is sutured to the scleral wall, enabling centration of the IOL-capsular bag complex. Six

Suture slippage in knotless suture anchors resulting in subacromial-subdeltoid bursitis.

Science.gov (United States)

Hayeri, Mohammad Reza; Keefe, Daniel T; Chang, Eric Y

2016-05-01

Rotator cuff repair using a suture bridge and knotless suture anchors is a relatively new, but increasingly used technique. The suture bridge technique creates an anatomically similar and more secure rotator cuff repair compared with conventional arthroscopic techniques and the use of knotless anchors eliminates the challenges associated with knot tying during arthroscopic surgery. However, previous in vitro biomechanical tests have shown that the hold of the suture in a knotless suture anchor is far lower than the pullout strength of the anchor from bone. Up until now slippage has been a theoretical concern. We present a prospectively diagnosed case of in vivo suture loosening after rotator cuff repair using a knotless bridge technique resulting in subacromial-subdeltoid bursitis.

Understanding Rasch Measurement: Partial Credit Model and Pivot Anchoring.

Science.gov (United States)

Bode, Rita K.

2001-01-01

Describes the Rasch measurement partial credit model, what it is, how it differs from other Rasch models, and when and how to use it. Also describes the calibration of instruments with increasingly complex items. Explains pivot anchoring and illustrates its use and describes the effect of pivot anchoring on step calibrations, item hierarchy, and…

Intermittent use of an "anchor system" improves postural control in healthy older adults.

Science.gov (United States)

Freitas, Milena de Bem Zavanella; Mauerberg-deCastro, Eliane; Moraes, Renato

2013-07-01

Haptic information, provided by a non-rigid tool (i.e., an "anchor system"), can reduce body sway in individuals who perform a standing postural task. However, it was not known whether or not continuous use of the anchor system would improve postural control after its removal. Additionally, it was unclear as to whether or not frequency of use of the anchor system is related to improved control in older adults. The present study evaluated the effect of the prolonged use of the anchor system on postural control in healthy older individuals, at different frequencies of use, while they performed a postural control task (semi-tandem position). Participants were divided into three groups according to the frequency of the anchor system's use (0%, 50%, and 100%). Pre-practice phase (without anchor) was followed by a practice phase (they used the anchor system at the predefined frequency), and a post-practice phase (immediate and late-without anchor). All three groups showed a persistent effect 15min after the end of the practice phase (immediate post-practice phase). However, only the 50% group showed a persistent effect in the late post-practice phase (24h after finishing the practice phase). Older adults can improve their postural control by practicing the standing postural task, and use of the anchor system limited to half of their practice time can provide additional improvement in their postural control. Copyright © 2013 Elsevier B.V. All rights reserved.

Model test of anchoring effect on zonal disintegration in deep surrounding rock masses.

Science.gov (United States)

Chen, Xu-Guang; Zhang, Qiang-Yong; Wang, Yuan; Liu, De-Jun; Zhang, Ning

2013-01-01

The deep rock masses show a different mechanical behavior compared with the shallow rock masses. They are classified into alternating fractured and intact zones during the excavation, which is known as zonal disintegration. Such phenomenon is a great disaster and will induce the different excavation and anchoring methodology. In this study, a 3D geomechanics model test was conducted to research the anchoring effect of zonal disintegration. The model was constructed with anchoring in a half and nonanchoring in the other half, to compare with each other. The optical extensometer and optical sensor were adopted to measure the displacement and strain changing law in the model test. The displacement laws of the deep surrounding rocks were obtained and found to be nonmonotonic versus the distance to the periphery. Zonal disintegration occurs in the area without anchoring and did not occur in the model under anchoring condition. By contrasting the phenomenon, the anchor effect of restraining zonal disintegration was revealed. And the formation condition of zonal disintegration was decided. In the procedure of tunnel excavation, the anchor strain was found to be alternation in tension and compression. It indicates that anchor will show the nonmonotonic law during suppressing the zonal disintegration.

Model Test of Anchoring Effect on Zonal Disintegration in Deep Surrounding Rock Masses

Directory of Open Access Journals (Sweden)

Xu-Guang Chen

2013-01-01

Full Text Available The deep rock masses show a different mechanical behavior compared with the shallow rock masses. They are classified into alternating fractured and intact zones during the excavation, which is known as zonal disintegration. Such phenomenon is a great disaster and will induce the different excavation and anchoring methodology. In this study, a 3D geomechanics model test was conducted to research the anchoring effect of zonal disintegration. The model was constructed with anchoring in a half and nonanchoring in the other half, to compare with each other. The optical extensometer and optical sensor were adopted to measure the displacement and strain changing law in the model test. The displacement laws of the deep surrounding rocks were obtained and found to be nonmonotonic versus the distance to the periphery. Zonal disintegration occurs in the area without anchoring and did not occur in the model under anchoring condition. By contrasting the phenomenon, the anchor effect of restraining zonal disintegration was revealed. And the formation condition of zonal disintegration was decided. In the procedure of tunnel excavation, the anchor strain was found to be alternation in tension and compression. It indicates that anchor will show the nonmonotonic law during suppressing the zonal disintegration.

Calculation of anchor forces on penetration liners for the reactor vessel Schmehausen (Germany)

International Nuclear Information System (INIS)

Roennert, J.K.

1976-01-01

Penetrations through the walls of the single cavity PCPV Prestressed Concrete Pressure Vessel for the 300 MW(e) reactor are lined with steel penetration liners welded to the liner of the cavity. For gas-tightness of the system the penetrations are closed by covers. To secure their integration with the concrete, the liners are anchored to it by means of shear studs and/or angles. Being embedded in concrete, over the full width of the walls, the liners are exposed to lateral and longitudinal concrete deformations causing forces on the anchors. The axial blow-out force due to the pressure of the coolant on the closures must also be transferred through the anchors to the concrete. In the design of anchored penetration liners stress analyses are performed to determine anchor forces under different loading conditions and at several ages of the PCPV. The present paper deals with the mathematical estimation of the anchor forces on the basis of given concrete deformations, temperature of liners, and pressure in the vessel by the method of replacing the penetration liners and their anchors by a spring model with linear stiffness characteristics for both the liner and the anchors. An example of the computations on a digital computer is shown. (author)

A scale distortion theory of anchoring.

Science.gov (United States)

Frederick, Shane W; Mochon, Daniel

2012-02-01

We propose that anchoring is often best interpreted as a scaling effect--that the anchor changes how the response scale is used, not how the focal stimulus is perceived. Of importance, we maintain that this holds true even for so-called objective scales (e.g., pounds, calories, meters, etc.). In support of this theory of scale distortion, we show that prior exposure to a numeric standard changes respondents' use of that specific response scale but does not generalize to conceptually affiliated judgments rendered on similar scales. Our findings highlight the necessity of distinguishing response language effects from representational effects in places where the need for that distinction has often been assumed away.

Retractable Robotic Anchor for Hard Rock and Granular Soils, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — ProtoInnovations, LLC, is developing an innovative retractable robotic anchor that works in hard rock and granular soils permitting anchoring and subsequent...

Software Note: Using BILOG for Fixed-Anchor Item Calibration

Science.gov (United States)

DeMars, Christine E.; Jurich, Daniel P.

2012-01-01

The nonequivalent groups anchor test (NEAT) design is often used to scale item parameters from two different test forms. A subset of items, called the anchor items or common items, are administered as part of both test forms. These items are used to adjust the item calibrations for any differences in the ability distributions of the groups taking…

Not all nutrition claims are perceived equal: anchoring effects and moderating mechanisms in food advertising.

Science.gov (United States)

Paek, Hye-Jin; Yoon, Hye Jin; Hove, Thomas

2011-03-01

Despite the increased use of health claims in food advertising, few studies have investigated how specific nutrition claims have differential effects depending on how they are presented. In this context, the current study tests the anchoring hypothesis. Anchoring refers to a common human tendency to evaluate information differently depending on the presence or absence of a numerical "anchor" or reference point. Two (pilot and main) experimental studies explore anchoring effects on audience response to food advertising both directly and moderated by cognitive, motivational, and message factors. The pilot study finds that food product ads employing nutrition claims with an anchor rather than without an anchor generate two results: First, participants perceive the product to have lower fat/lower calorie contents (anchoring hypothesis); second, they prefer the messages with an anchor over those without an anchor. The main study reports that when anchoring is successfully evoked, it produces favorable attitudes toward the ad, favorable attitudes toward the brand, and purchase intention-but only when moderated by health orientation, claim believability, and nutrition knowledge. Practical implications are provided with respect to regulatory guidelines and effective communication strategies for promoting low-fat and low-calorie products in food advertising.

Career Anchors: Results of an Organisational Study in the UK.

Science.gov (United States)

Yarnall, Jane

1998-01-01

Career anchors of 374 British employees were identified using Schein's questionnaire. Age, gender, and length of service had no significant effect on distribution of anchors. Job level had some relationship. The information could be used to determine appropriate career-development strategies. (SK)

Biomechanical Analysis of an Arthroscopic Broström Ankle Ligament Repair and a Suture Anchor-Augmented Repair.

Science.gov (United States)

Giza, Eric; Whitlow, Scott R; Williams, Brady T; Acevedo, Jorge I; Mangone, Peter G; Haytmanek, C Thomas; Curry, Eugene E; Turnbull, Travis Lee; LaPrade, Robert F; Wijdicks, Coen A; Clanton, Thomas O

2015-07-01

Secondary surgical repair of ankle ligaments is often indicated in cases of chronic lateral ankle instability. Recently, arthroscopic Broström techniques have been described, but biomechanical information is limited. The purpose of the present study was to analyze the biomechanical properties of an arthroscopic Broström repair and augmented repair with a proximally placed suture anchor. It was hypothesized that the arthroscopic Broström repairs would compare favorably to open techniques and that augmentation would increase the mean repair strength at time zero. Twenty (10 matched pairs) fresh-frozen foot and ankle cadaveric specimens were obtained. After sectioning of the lateral ankle ligaments, an arthroscopic Broström procedure was performed on each ankle using two 3.0-mm suture anchors with #0 braided polyethylene/polyester multifilament sutures. One specimen from each pair was augmented with a 2.9-mm suture anchor placed 3 cm proximal to the inferior tip of the lateral malleolus. Repairs were isolated and positioned in 20 degrees of inversion and 10 degrees of plantarflexion and loaded to failure using a dynamic tensile testing machine. Maximum load (N), stiffness (N/mm), and displacement at maximum load (mm) were recorded. There were no significant differences between standard arthroscopic repairs and the augmented repairs for mean maximum load and stiffness (154.4 ± 60.3 N, 9.8 ± 2.6 N/mm vs 194.2 ± 157.7 N, 10.5 ± 4.7 N/mm, P = .222, P = .685). Repair augmentation did not confer a significantly higher mean strength or stiffness at time zero. Mean strength and stiffness for the arthroscopic Broström repair compared favorably with previous similarly tested open repair and reconstruction methods, validating the clinical feasibility of an arthroscopic repair. However, augmentation with an additional proximal suture anchor did not significantly strengthen the repair. © The Author(s) 2015.

Robotic Ankle for Omnidirectional Rock Anchors

Science.gov (United States)

Parness, Aaron; Frost, Matthew; Thatte, Nitish

2013-01-01

Future robotic exploration of near-Earth asteroids and the vertical and inverted rock walls of lava caves and cliff faces on Mars and other planetary bodies would require a method of gripping their rocky surfaces to allow mobility without gravitational assistance. In order to successfully navigate this terrain and drill for samples, the grippers must be able to produce anchoring forces in excess of 100 N. Additionally, the grippers must be able to support the inertial forces of a moving robot, as well gravitational forces for demonstrations on Earth. One possible solution would be to use microspine arrays to anchor to rock surfaces and provide the necessary load-bearing abilities for robotic exploration of asteroids. Microspine arrays comprise dozens of small steel hooks supported on individual suspensions. When these arrays are dragged along a rock surface, the steel hooks engage with asperities and holes on the surface. The suspensions allow for individual hooks to engage with asperities while the remaining hooks continue to drag along the surface. This ensures that the maximum possible number of hooks engage with the surface, thereby increasing the load-bearing abilities of the gripper. Using the microspine array grippers described above as the end-effectors of a robot would allow it to traverse terrain previously unreachable by traditional wheeled robots. Furthermore, microspine-gripping robots that can perch on cliffs or rocky walls could enable a new class of persistent surveillance devices for military applications. In order to interface these microspine grippers with a legged robot, an ankle is needed that can robotically actuate the gripper, as well as allow it to conform to the large-scale irregularities in the rock. The anchor serves three main purposes: deploy and release the anchor, conform to roughness or misalignment with the surface, and cancel out any moments about the anchor that could cause unintentional detachment. The ankle design contains a

Mercury-induced hepatotoxicity in zebrafish: in vivo mechanistic insights from transcriptome analysis, phenotype anchoring and targeted gene expression validation

Directory of Open Access Journals (Sweden)

Mathavan Sinnakaruppan

2010-03-01

Full Text Available Abstract Background Mercury is a prominent environmental contaminant that causes detrimental effects to human health. Although the liver has been known to be a main target organ, there is limited information on in vivo molecular mechanism of mercury-induced toxicity in the liver. By using transcriptome analysis, phenotypic anchoring and validation of targeted gene expression in zebrafish, mercury-induced hepatotoxicity was investigated and a number of perturbed cellular processes were identified and compared with those captured in the in vitro human cell line studies. Results Hepato-transcriptome analysis of mercury-exposed zebrafish revealed that the earliest deregulated genes were associated with electron transport chain, mitochondrial fatty acid beta-oxidation, nuclear receptor signaling and apoptotic pathway, followed by complement system and proteasome pathway, and thereafter DNA damage, hypoxia, Wnt signaling, fatty acid synthesis, gluconeogenesis, cell cycle and motility. Comparative meta-analysis of microarray data between zebrafish liver and human HepG2 cells exposed to mercury identified some common toxicological effects of mercury-induced hepatotoxicity in both models. Histological analyses of liver from mercury-exposed fish revealed morphological changes of liver parenchyma, decreased nucleated cell count, increased lipid vesicles, glycogen and apoptotic bodies, thus providing phenotypic evidence for anchoring of the transcriptome analysis. Validation of targeted gene expression confirmed deregulated gene-pathways from enrichment analysis. Some of these genes responding to low concentrations of mercury may serve as toxicogenomic-based markers for detection and health risk assessment of environmental mercury contaminations. Conclusion Mercury-induced hepatotoxicity was triggered by oxidative stresses, intrinsic apoptotic pathway, deregulation of nuclear receptor and kinase activities including Gsk3 that deregulates Wnt signaling

Assessment of behavior, design and testing of anchors for fastening to concrete

Energy Technology Data Exchange (ETDEWEB)

Yoon, Young Soo; Choi, Han Tae; Jung, Woo Young; Park, Sung Kyun [Korea Univ., Seoul (Korea, Republic of)

1998-11-15

This report presents the evaluation of behavior and the prediction of tensile capacity of anchors that fail concrete, as the design basis for anchorage. Tests of cast-in place headed anchors, domestically manufactured and installed in uncracked, unreinforced concrete were performed to investigate the behavior of single anchors and multiple anchors with the consideration of various embedment lengths and edge distances. The failure mode and the load-deformation response of these anchors are discussed and the concrete failure data then compared with capacities by the two exiting methods : the 45 degree cone method of ACI 349, appendix B and the Concrete Capacity Design (CCD) method. Discrepancies between the test results and these two prediction methods are assessed and also the basic differences in philosophy and the factors contributing to the philosophical differences in these two methods are addressed.

Effects of anchoring and adjustment in the evaluation of product pricing.

Science.gov (United States)

Elaad, Eitan; Sayag, Neta; Ezer, Aliya

2010-08-01

Anchoring and adjustment comprise a heuristic that creates expectations. Two types of anchors were applied on participants' evaluation of products: the price reference of the product (maximum, minimum, or no price reference) and the context in which the products were evaluated (the prestige of the shopping center). Results showed that both factors anchored evaluations of products' value. Context effects were explained by the different expectations of visitors in prestigious (looking for quality) and less prestigious (seeking a bargain) centers.

Characterization of the C-terminal ER membrane anchor of PTP1B

International Nuclear Information System (INIS)

Anderie, Ines; Schulz, Irene; Schmid, Andreas

2007-01-01

The tyrosine phosphatase PTP1B is an important regulator of cell function. In living cells PTP1B activity is restricted to the vicinity of the endoplasmic reticulum (ER) by post-translational C-terminal attachment of PTP1B to the ER membrane network. In our study we investigated the membrane anchor of PTP1B by use of EGFP fusion proteins. We demonstrate that the membrane anchor of PTP1B cannot be narrowed down to a unique amino acid sequence with a defined start and stop point but rather is moveable within several amino acids. Removal of up to seven amino acids from the C-terminus, as well as exchange of single amino acids in the putative transmembrane sequence did not influence subcellular localization of PTP1B. With the method of bimolecular fluorescence complementation we could demonstrate dimerization of PTP1B in vivo. Homodimerization was, in contrast to other tail-anchored proteins, not dependent on the membrane anchor. Our data demonstrate that the C-terminal membrane anchor of PTP1B is formed by a combination of a single stretch transmembrane domain (TMD) followed by a tail. TMD and tail length are variable and there are no sequence-specific features. Our data for PTP1B are consistent with a concept that explains the ER membrane anchor of tail-anchored proteins as a physicochemical structure

Bone anchors or interference screws? A biomechanical evaluation for autograft ankle stabilization.

Science.gov (United States)

Jeys, Lee; Korrosis, Sotiris; Stewart, Todd; Harris, Nicholas J

2004-01-01

Autograft stabilization uses free semitendinosus tendon grafts to anatomically reconstruct the anterior talofibular ligament. Study aims were to evaluate the biomechanical properties of Mitek GII anchors compared with the Arthrex Bio-Tenodesis Screw for free tendon reconstruction of the anterior talofibular ligament. There are no differences in load to failure and percentage specimen elongation at failure between the 2 methods. Controlled laboratory study using porcine models. Sixty porcine tendon constructs were failure tested. Re-creating the pull of the anterior talofibular ligament, loads were applied at 70 degrees to the bones. Thirty-six tendons were fixed to porcine tali and tested using a single pull to failure; 10 were secured with anchors and No. 2 Ethibond, 10 with anchors and FiberWire, 10 with screws and Fiberwire, and 6 with partially gripped screws. Cyclic preloading was conducted on 6 tendons fixed by anchors and on 6 tendons fixed by screws before failure testing. Two groups of 6 components fixed to the fibula were also tested. The talus single-pull anchor group produced a mean load of 114 N and elongation of 37% at failure. The talus single-pull screw group produced a mean load of 227 N and elongation of 22% at failure (P anchors. The improved biomechanics of interference screws suggests that these may be more suited to in vivo reconstruction of the anterior talofibular ligament than are bone anchors.

Reinforcing mechanism of anchors in slopes: a numerical comparison of results of LEM and FEM

Science.gov (United States)

Cai, Fei; Ugai, Keizo

2003-06-01

This paper reports the limitation of the conventional Bishop's simplified method to calculate the safety factor of slopes stabilized with anchors, and proposes a new approach to considering the reinforcing effect of anchors on the safety factor. The reinforcing effect of anchors can be explained using an additional shearing resistance on the slip surface. A three-dimensional shear strength reduction finite element method (SSRFEM), where soil-anchor interactions were simulated by three-dimensional zero-thickness elasto-plastic interface elements, was used to calculate the safety factor of slopes stabilized with anchors to verify the reinforcing mechanism of anchors. The results of SSRFEM were compared with those of the conventional and proposed approaches for Bishop's simplified method for various orientations, positions, and spacings of anchors, and shear strengths of soil-grouted body interfaces. For the safety factor, the proposed approach compared better with SSRFEM than the conventional approach. The additional shearing resistance can explain the influence of the orientation, position, and spacing of anchors, and the shear strength of soil-grouted body interfaces on the safety factor of slopes stabilized with anchors.

Anchoring in a novel bimanual coordination pattern.

Science.gov (United States)

Maslovat, Dana; Lam, Melanie Y; Brunke, Kirstin M; Chua, Romeo; Franks, Ian M

2009-02-01

Anchoring in cyclical movements has been defined as regions of reduced spatial or temporal variability [Beek, P. J. (1989). Juggling dynamics. PhD thesis. Amsterdam: Free University Press] that are typically found at movement reversal points. For in-phase and anti-phase movements, synchronizing reversal points with a metronome pulse has resulted in decreased anchor point variability and increased pattern stability [Byblow, W. D., Carson, R. G., & Goodman, D. (1994). Expressions of asymmetries and anchoring in bimanual coordination. Human Movement Science, 13, 3-28; Fink, P. W., Foo, P., Jirsa, V. K., & Kelso, J. A. S. (2000). Local and global stabilization of coordination by sensory information. Experimental Brain Research, 134, 9-20]. The present experiment examined anchoring during acquisition, retention, and transfer of a 90 degrees phase-offset continuous bimanual coordination pattern (whereby the right limb lags the left limb by one quarter cycle), involving horizontal flexion about the elbow. Three metronome synchronization strategies were imposed: participants either synchronized maximal flexion of the right arm (i.e., single metronome), both flexion and extension of the right arm (i.e., double metronome within-limb), or flexion of each arm (i.e., double metronome between-limb) to an auditory metronome. In contrast to simpler in-phase and anti-phase movements, synchronization of additional reversal points to the metronome did not reduce reversal point variability or increase pattern stability. Furthermore, practicing under different metronome synchronization strategies did not appear to have a significant effect on the rate of acquisition of the pattern.

Chemical Reactive Anchoring Lipids with Different Performance for Cell Surface Re-engineering Application.

Science.gov (United States)

Vabbilisetty, Pratima; Boron, Mallorie; Nie, Huan; Ozhegov, Evgeny; Sun, Xue-Long

2018-02-28

Introduction of selectively chemical reactive groups at the cell surface enables site-specific cell surface labeling and modification opportunity, thus facilitating the capability to study the cell surface molecular structure and function and the molecular mechanism it underlies. Further, it offers the opportunity to change or improve a cell's functionality for interest of choice. In this study, two chemical reactive anchor lipids, phosphatidylethanolamine-poly(ethylene glycol)-dibenzocyclooctyne (DSPE-PEG 2000 -DBCO) and cholesterol-PEG-dibenzocyclooctyne (CHOL-PEG 2000 -DBCO) were synthesized and their potential application for cell surface re-engineering via lipid fusion were assessed with RAW 264.7 cells as a model cell. Briefly, RAW 264.7 cells were incubated with anchor lipids under various concentrations and at different incubation times. The successful incorporation of the chemical reactive anchor lipids was confirmed by biotinylation via copper-free click chemistry, followed by streptavidin-fluorescein isothiocyanate binding. In comparison, the cholesterol-based anchor lipid afforded a higher cell membrane incorporation efficiency with less internalization than the phospholipid-based anchor lipid. Low cytotoxicity of both anchor lipids upon incorporation into the RAW 264.7 cells was observed. Further, the cell membrane residence time of the cholesterol-based anchor lipid was evaluated with confocal microscopy. This study suggests the potential cell surface re-engineering applications of the chemical reactive anchor lipids.

Chemical Reactive Anchoring Lipids with Different Performance for Cell Surface Re-engineering Application

Science.gov (United States)

2018-01-01

Introduction of selectively chemical reactive groups at the cell surface enables site-specific cell surface labeling and modification opportunity, thus facilitating the capability to study the cell surface molecular structure and function and the molecular mechanism it underlies. Further, it offers the opportunity to change or improve a cell’s functionality for interest of choice. In this study, two chemical reactive anchor lipids, phosphatidylethanolamine–poly(ethylene glycol)–dibenzocyclooctyne (DSPE–PEG2000–DBCO) and cholesterol–PEG–dibenzocyclooctyne (CHOL–PEG2000–DBCO) were synthesized and their potential application for cell surface re-engineering via lipid fusion were assessed with RAW 264.7 cells as a model cell. Briefly, RAW 264.7 cells were incubated with anchor lipids under various concentrations and at different incubation times. The successful incorporation of the chemical reactive anchor lipids was confirmed by biotinylation via copper-free click chemistry, followed by streptavidin-fluorescein isothiocyanate binding. In comparison, the cholesterol-based anchor lipid afforded a higher cell membrane incorporation efficiency with less internalization than the phospholipid-based anchor lipid. Low cytotoxicity of both anchor lipids upon incorporation into the RAW 264.7 cells was observed. Further, the cell membrane residence time of the cholesterol-based anchor lipid was evaluated with confocal microscopy. This study suggests the potential cell surface re-engineering applications of the chemical reactive anchor lipids. PMID:29503972

An anchoring system for fish habitat structures: field technique, evaluation, and application.

Science.gov (United States)

Barbara L. Fontaine; Thomas D. Merritt

1988-01-01

Steel cable can be used to bind rocks and logs together to construct fish habitat structures in streams. Cables must be securely anchored if structures are to withstand floods. This paper describes a way to anchor cables into bedrock or ballast boulders. Anchor tensile strength ranged from 7,500 to 36,500 pounds and was related to type of resin and embedment depth....

Knotless single-row rotator cuff repair: a comparative biomechanical study of 2 knotless suture anchors.

Science.gov (United States)

Efird, Chad; Traub, Shaun; Baldini, Todd; Rioux-Forker, Dana; Spalazzi, Jeffrey P; Davisson, Twana; Hawkins, Monica; McCarty, Eric

2013-08-01

The purpose of this study was to compare the gap formation during cyclic loading, maximum repair strength, and failure mode of single-row full-thickness supraspinatus repairs performed using 2 knotless suture anchors with differing internal suture-retention mechanisms in a human cadaver model. Nine matched pairs of cadaver shoulders were used. Full-thickness tears were induced by detaching the supraspinatus tendon from the greater tuberosity. Single-row repairs were performed with either type I (Opus Magnum PI; ArthroCare, Austin, Texas) or type II (ReelX STT; Stryker, Mahwah, New Jersey) knotless suture anchors. The repaired tendon was cycled from 10 to 90 N for 500 cycles, followed by load to failure. Gap formation was measured at 5, 100, 200, 300, 400, and 500 cycles with a video digitizing system. Anchor type or location (anterior or posterior) had no effect on gap formation during cyclic loading regardless of position (anterior, P=.385; posterior, P=.389). Maximum load to failure was significantly greater (P=.018) for repairs performed with type II anchors (288±62 N) compared with type I anchors (179±39 N). Primary failure modes were anchor pullout and tendon tearing for type II anchors and suture slippage through the anchor for type I anchors. The internal ratcheting suture-retention mechanism of type II anchors may have helped this anchor outperform the suture-cinching mechanism of type I anchors by supporting significantly higher loads before failure and minimizing suture slippage, potentially leading to stronger repairs clinically. Copyright 2013, SLACK Incorporated.

A radiographic investigation to determine the safety of suture anchor systems for pediatric modified Broström ankle ligament reconstruction.

Science.gov (United States)

Hazratwala, Kaushik; Best, Alistair; Kopplin, Matthew; Giza, Eric; Sullivan, Martin

2005-03-01

The modified Broström ligament reconstruction using anchor sutures has been performed in adults with clinical success; however, the safety parameters for the use of suture anchors in adolescent lateral ankle ligament reconstruction have not been established. To perform a radiographic analysis comparing the depth of penetration of suture anchors in adult ankle ligament reconstruction with the average distance of the physis from the tip of the fibula in adolescents. Cross-sectional study, Level of evidence, 4. Forty postoperative ankle radiographs of adult patients who had a modified Broström procedure were compared with 40 normal adolescent ankle radiographs. In the adult group, the distance of the suture anchor penetration from the distal tip of the fibula was measured; in the adolescent group, the distance of the physis from the distal tip of the fibula was measured. The mean depth of the suture anchors was 17 mm (range, 14-21 mm) from the tip of the fibula in the adult group, and the mean distance of the growth plate was 23 mm (range, 18-29 mm) in the adolescent group. Eight radiographs from the adolescent group (20%) had a physis measurement of ankle ligament repair in the skeletally immature patient using suture anchors.

Suture anchor tenodesis in repair of distal Achilles tendon injuries.

Science.gov (United States)

Kiliçoğlu, Onder; Türker, Mehmet; Yildız, Fatih; Akalan, Ekin; Temelli, Yener

2014-01-01

Distal Achilles tendon avulsions are in the form of either bony and nonbony avulsion of Achilles tendon from its calcaneal insertion. Four patients with distal Achilles tendon avulsions or ruptures which were treated with tendon to bone repair using suture anchors are presented here. Operated leg was immobilized in above-knee cast for 4 weeks while the patient walked non-weight-bearing. Then, cast was changed to below knee, and full weight-bearing was allowed. Patients underwent gait analysis minimum at first postoperative year. Mean American Orthopedics Foot Ankle Society ankle/hindfoot score of patients at last visit was 88.75 (range 85-100), and Achilles tendon total rupture score was 77.75 (range 58-87). Mean passive dorsiflexion of injured ankles (14° ± 5°) was lower than uninjured ankles (23° ± 9°). All the kinematic parameters of gait analysis were comparable to the uninjured side. Maximum plantar flexion power of injured ankle was 1.40 W/kg, and this was significantly lower than the contralateral side value 2.38 W/kg; (P = 0.0143). There were no visually altered gait or problems in daily life. Suture anchor tenodesis technique of distal Achilles tendon avulsions was successful in achieving durable osteotendinous repairs.

Development of a Behaviorally Anchored Rating Scale for Leadership

Science.gov (United States)

2018-01-01

Research Product 2018-06 Development of a Behaviorally Anchored Rating Scale for Leadership Tatiana H. Toumbeva Krista L...anchored Rating Scale for Leadership 5a. CONTRACT NUMBER W5J9CQ-11-D-0004 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 62278 6...observer- based behavioral measure to help instructors more reliably and accurately evaluate the development of leadership attributes and competencies

Management of subluxated capsular bag-fixated intraocular lenses using a capsular anchor.

Science.gov (United States)

Ton, Yokrat; Naftali, Modi; Gortzak, Ruth Lapid; Assia, Ehud I

2016-05-01

We describe the use of the capsular anchor (AssiAnchor) to manage a subluxated intraocular lens (IOL) in the capsular bag. The anchor comprises 2 prongs that hold the anterior lens capsule and a central rod that is sutured to the scleral wall, enabling centration of the IOL-capsular bag complex. Six pseudophakic patients presenting with subluxated posterior chamber IOLs in the capsular bag were operated on using the device. The anchor was used successfully in all cases, although in 2 cases only 1 prong was placed under the capsulorhexis edge. In 1 eye, 2 anchors were used 1 month apart following repeated traumatic zonular injury. The capsular bag holding the IOL remained centered and stable throughout the follow-up period. The anchoring device, which was originally designed to preserve the lens capsule and stabilize subluxated crystalline lenses, can also be used to treat subluxation of a capsular bag-fixated IOL. Dr. Assia is the inventor of the AssiAnchor, has a licensed patent of the anchor, and is consultant to Hanita Lenses. Dr. Lapid-Gortzak is a consultant to and speaker for Alcon Surgical, Inc., Hanita Lenses, Orca Surgical, and Sanoculis Ltd.; a speaker for Santen; and a consultant to Icon. Drs. Ton and Naftali have no financial or proprietary interest in any material or method mentioned. Copyright © 2016 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

Pipe supports and anchors - LMFBR applications

International Nuclear Information System (INIS)

Anderson, M.J.

1983-06-01

Pipe design and support design can not be treated as separate disciplines. A coordinated design approach is required if LMFBR pipe system adequacy is to be achieved at a reasonable cost. It is particularly important that system designers understand and consider those factors which influence support train flexibility and thus the pipe system dynamic stress levels. The system approach must not stop with the design phase but should continue thru the erection and acceptance test procedures. The factors that should be considered in the design of LMFBR pipe supports and anchors are described. The various pipe support train elements are described together with guidance on analysis, design and application aspects. Post erection acceptance and verification test procedures are then discussed

Seismic response of unanchored and partially anchored liquid-storage tanks. Final report

International Nuclear Information System (INIS)

Malhotra, P.K.; Veletsos, A.S.

1995-12-01

Ground-mounted vertical storage tanks are important components of nuclear plant safety systems. A systematic study is made of the principal effects of base uplifting on the seismic response of laterally excited, unanchored and partially anchored cylindrical liquid-storage tanks. The study consists of two parts: the first deals with the static uplifting resistance of the flexible base plate, and the second deals with the dynamic response of the uplifting system. An insight into the behavior of the uplifting base plate is first gained with the help of a prismatic beam solution. In Section 2, the solution is implemented exactly, whereas in Section 3 it is implemented approximately by use of the Ritz energy procedure. Solutions are next presented for axisymmetrically and asymmetrically uplifted base plate of tanks, in Section 4. For the axisymmetric case the solution is implemented exactly, as well as approximately by modeling the plate by a series of semiinfinite prismatic beams. The accuracy of the latter approach is confirmed by comparing its predictions with those of the former. In Section 5, a highly efficient and rational method is presented for the dynamic response analysis of uplifting tanks. Both unanchored tanks and partially anchored tanks, for which the number of anchor bolts at the base is insufficient to ensure full fixity, are considered. It is shown that base uplifting may reduce significantly the hydrodynamic pressures, but these reductions may be associated with increased axial compressive stresses in the tank wall and large plastic rotations at the plate-shell junction. For partially anchored tanks, energy loss due to bolt yielding is found to be small

Spontaneous insertion of GPI anchors into cholesterol-rich membrane domains

Directory of Open Access Journals (Sweden)

Jing Li

2018-05-01

Full Text Available GPI-Anchored proteins (GPI-APs can be exogenously transferred onto bilayer membranes both in vivo and in vitro, while the mechanism by which this transfer process occurs is unknown. In this work, we used atomistic molecular dynamics simulations and free energy calculations to characterize the essential influence of cholesterol on insertion of the GPI anchors into plasma membranes. We demonstrate, both dynamically and energetically, that in the presence of cholesterol, the tails of GPI anchors are able to penetrate inside the core of the lipid membrane spontaneously with a three-step mechanism, while in the absence of cholesterol no spontaneous insertion was observed. We ascribe the failure of insertion to the strong thermal fluctuation of lipid molecules in cholesterol-free bilayer, which generates a repulsive force in entropic origin. In the presence of cholesterol, however, the fluctuation of lipids is strongly reduced, thus decreasing the barrier for the anchor insertion. Based on this observation, we propose a hypothesis that addition of cholesterol creates vertical creases in membranes for the insertion of acyl chains. Moreover, we find that the GPI anchor could also spontaneously inserted into the boundary between cholesterol-rich and cholesterol-depleted domains. Our results shed light on the mechanism of cholesterol-mediated interaction between membrane proteins with acyl chain and plasma membranes in living cells.

Spontaneous insertion of GPI anchors into cholesterol-rich membrane domains

Science.gov (United States)

Li, Jing; Liu, Xiuhua; Tian, Falin; Yue, Tongtao; Zhang, Xianren; Cao, Dapeng

2018-05-01

GPI-Anchored proteins (GPI-APs) can be exogenously transferred onto bilayer membranes both in vivo and in vitro, while the mechanism by which this transfer process occurs is unknown. In this work, we used atomistic molecular dynamics simulations and free energy calculations to characterize the essential influence of cholesterol on insertion of the GPI anchors into plasma membranes. We demonstrate, both dynamically and energetically, that in the presence of cholesterol, the tails of GPI anchors are able to penetrate inside the core of the lipid membrane spontaneously with a three-step mechanism, while in the absence of cholesterol no spontaneous insertion was observed. We ascribe the failure of insertion to the strong thermal fluctuation of lipid molecules in cholesterol-free bilayer, which generates a repulsive force in entropic origin. In the presence of cholesterol, however, the fluctuation of lipids is strongly reduced, thus decreasing the barrier for the anchor insertion. Based on this observation, we propose a hypothesis that addition of cholesterol creates vertical creases in membranes for the insertion of acyl chains. Moreover, we find that the GPI anchor could also spontaneously inserted into the boundary between cholesterol-rich and cholesterol-depleted domains. Our results shed light on the mechanism of cholesterol-mediated interaction between membrane proteins with acyl chain and plasma membranes in living cells.

AnchorDock for Blind Flexible Docking of Peptides to Proteins.

Science.gov (United States)

Slutzki, Michal; Ben-Shimon, Avraham; Niv, Masha Y

2017-01-01

Due to increasing interest in peptides as signaling modulators and drug candidates, several methods for peptide docking to their target proteins are under active development. The "blind" docking problem, where the peptide-binding site on the protein surface is unknown, presents one of the current challenges in the field. AnchorDock protocol was developed by Ben-Shimon and Niv to address this challenge.This protocol narrows the docking search to the most relevant parts of the conformational space. This is achieved by pre-folding the free peptide and by computationally detecting anchoring spots on the surface of the unbound protein. Multiple flexible simulated annealing molecular dynamics (SAMD) simulations are subsequently carried out, starting from pre-folded peptide conformations, constrained to the various precomputed anchoring spots.Here, AnchorDock is demonstrated using two known protein-peptide complexes. A PDZ-peptide complex provides a relatively easy case due to the relatively small size of the protein, and a typical peptide conformation and binding region; a more challenging example is a complex between USP7 N-term and a p53-derived peptide, where the protein is larger, and the peptide conformation and a binding site are generally assumed to be unknown. AnchorDock returned native-like solutions ranked first and third for the PDZ and USP7 complexes, respectively. We describe the procedure step by step and discuss possible modifications where applicable.

Murasaki: a fast, parallelizable algorithm to find anchors from multiple genomes.

Directory of Open Access Journals (Sweden)

Kris Popendorf

Full Text Available BACKGROUND: With the number of available genome sequences increasing rapidly, the magnitude of sequence data required for multiple-genome analyses is a challenging problem. When large-scale rearrangements break the collinearity of gene orders among genomes, genome comparison algorithms must first identify sets of short well-conserved sequences present in each genome, termed anchors. Previously, anchor identification among multiple genomes has been achieved using pairwise alignment tools like BLASTZ through progressive alignment tools like TBA, but the computational requirements for sequence comparisons of multiple genomes quickly becomes a limiting factor as the number and scale of genomes grows. METHODOLOGY/PRINCIPAL FINDINGS: Our algorithm, named Murasaki, makes it possible to identify anchors within multiple large sequences on the scale of several hundred megabases in few minutes using a single CPU. Two advanced features of Murasaki are (1 adaptive hash function generation, which enables efficient use of arbitrary mismatch patterns (spaced seeds and therefore the comparison of multiple mammalian genomes in a practical amount of computation time, and (2 parallelizable execution that decreases the required wall-clock and CPU times. Murasaki can perform a sensitive anchoring of eight mammalian genomes (human, chimp, rhesus, orangutan, mouse, rat, dog, and cow in 21 hours CPU time (42 minutes wall time. This is the first single-pass in-core anchoring of multiple mammalian genomes. We evaluated Murasaki by comparing it with the genome alignment programs BLASTZ and TBA. We show that Murasaki can anchor multiple genomes in near linear time, compared to the quadratic time requirements of BLASTZ and TBA, while improving overall accuracy. CONCLUSIONS/SIGNIFICANCE: Murasaki provides an open source platform to take advantage of long patterns, cluster computing, and novel hash algorithms to produce accurate anchors across multiple genomes with

Organisation, ‘anchoring’ of knowledge, and innovation in the construction industry

DEFF Research Database (Denmark)

Drejer, Ina; Vinding, Anker Lund

2004-01-01

explanation for the relatively poor innovation performance of the industry. Using survey data from the Danish construction industry the paper investigates the importance of learning and ?anchoring? of project specific knowledge within the firms for facilitating engagement in innovative activities...... at the firm level. The data refer to the overall Danish construction industry, as well as a specific region, North Jutland, which is relatively specialised in construction. By using latent class and regression analysis the results show that firms, which to a high extent make use of partnering and other...... interorganisational features, combined with internal product and process evaluation and knowledge diffusion, are more likely to engage in innovative activities than firms that make less use of what we label ?knowledge anchoring mechanisms?. This indicates that there are ways for firms to compensate for the problems...

A Study on the Holding Capacity Safety Factors for Torpedo Anchors

Directory of Open Access Journals (Sweden)

Luís V. S. Sagrilo

2012-01-01

Full Text Available The use of powerful numerical tools based on the finite-element method has been improving the prediction of the holding capacity of fixed anchors employed by the offshore oil industry. One of the main achievements of these tools is the reduction of the uncertainty related to the holding capacity calculation of these anchors. Therefore, it is also possible to reduce the values of the associated design safety factors, which have been calibrated relying on models with higher uncertainty, without impairing the original level of structural safety. This paper presents a study on the calibration of reliability-based safety factors for the design of torpedo anchors considering the statistical model uncertainty evaluated using results from experimental tests and their correspondent finite-element-based numerical predictions. Both working stress design (WSD and load and resistance factors design (LRFD design methodologies are investigated. Considering the WSD design methodology, the single safety is considerably lower than the value typically employed in the design of torpedo anchors. Moreover, a LRFD design code format for torpedo anchors is more appropriate since it leads to designs having less-scattered safety levels around the target value.

A study on plate anchor detailing systems of shear re-bar

International Nuclear Information System (INIS)

Tsurumaki, S.; Ujiie, K.; Nishikawa, T.; Kitayama, K.

1995-01-01

For shell walls and base slabs in reactor buildings, besides a large amount of main bars, numerous shear re-bars have been employed to resist to out-of-plane force. As a result , detailing work involving shear re-bar is extremely involved. For example, the employed re-bar anchor method differs from the ordinary methods in which, a end of shear re-bar with 135-degrees hook or with anchor plate type and another re-bar end with 90-degrees hook are used. However the structural characteristics in members using shear re-bar of the bolt-mounted anchor plate have not yet been examined. A test was performed to confirm the effects of anchor methods for shear re-bars on shearing behavior of members. This paper describes the test plan, method and results. (author). 12 figs., 7 tabs

Grapnel stone anchors from Saurashtra: Remnants of Indo-Arab trade on the Indian coast

Digital Repository Service at National Institute of Oceanography (India)

Gaur, A.S.; Sundaresh; Tripati, S.

Stone anchors have been used as a primary source of information on ancient navigation by marine archaeologists since long. These anchors used by ancient mariners are often noticed underwater at various places across the world. Stone anchors are also...

Attaching transmitters to waterbirds using one versus two subcutaneous anchors: Retention and survival trade-offs

Science.gov (United States)

Lewis, Tyler; Esler, Daniel N.; Uher-Koch, Brian D.; Dickson, Rian D.; Anderson, Eric M.; Evenson, Joseph R.; Hupp, Jerry; Flint, Paul L.

2017-01-01

A major challenge of wildlife telemetry is choosing an attachment technique that maximizes transmitter retention while minimizing negative side effects. For waterbirds, attachment of transmitters with subcutaneous anchors has been an effective and well-established technique, having been used on >40 species. This method was recently modified to include a second subcutaneous anchor, presumably increasing transmitter retention beyond that of single-anchor attachments. This putative benefit may be offset, however, by increased health risks related to additional incisions and subcutaneous protrusions. To test this potential trade-off, we attached radiotransmitters to molting and wintering surf (Melanitta perspicillata) and white-winged scoters (M. fusca) during 2008 and 2009 in Washington State and southeast Alaska, USA, using single- (121 scoters) and double-anchor (128 scoters) attachment techniques. We estimated daily probabilities of survival and radio retention for each group, this being apparent retention for wintering scoters because we could not differentiate shed transmitters from flighted emigration. For scoters during the flightless remigial molt, we found that addition of a second anchor increased cumulative retention probability (±SE) over a 49-day period from 0.69 ± 0.11 for single-anchor to 0.88 ± 0.07 for double-anchor attachments, while having no effect on survival. However, during winter, scoters with double-anchor attachments experienced no improvement in apparent retention, while having significantly lower survival during their first 14 days following transmitter attachment; of 15 mortalities during this period, 11 had 2 subcutaneous anchors. From day 15 onward, winter survival rates were nearly identical for single- versus double-anchor attachments, indicating that adverse effects of subcutaneous anchors were mainly limited to the 14-day postattachment period. Overall, given that the survival cost of adding a second subcutaneous anchor

A biomechanical analysis of a single-row suture anchor fixation of a large bony bankart lesion.

Science.gov (United States)

Dyskin, Evgeny; Marzo, John M; Howard, Craig; Ehrensberger, Mark

2014-12-01

This study was conducted to assess whether a single-row suture anchor repair of a bony Bankart lesion comprising 19% of the glenoid length restores peak translational force and glenoid depth compared with the intact shoulder. Nine thawed adult cadaveric shoulders were dissected and mounted in 45° of abduction and 30° of external rotation. A bony Bankart lesion was simulated with an anterior longitudinal osteotomy, parallel to the superoinferior axis of the glenoid, equivalent to 19% of the glenoid length. The humeral head was displaced 10 mm anteriorly at a speed of 2 mm/s with a 50-N compressive load applied. Testing was performed with the glenoid intact, a simulated lesion, and the lesion repaired with 3 single-row suture anchors. Median (interquartile range [IQR]) peak translational force and glenoid depth were reported. The Friedman test and post hoc comparisons with the Wilcoxon signed rank test were used for between-group analyses. Peak translational force decreased after osteotomy (13.7 N; IQR, 9.6 to 15.5 N; P = .01) and increased after the repair (18.3 N; IQR, 18.3 to 20.6 N; P = .01) compared with the intact shoulder (23.7 N; IQR, 16.4 to 29.9 N). Glenoid depth significantly decreased after the osteotomy (0.2 mm; IQR, -0.6 to 0.7 mm) compared with baseline (1.7 mm; IQR, 1.3 to 2.0 mm; P = .01) and increased after repair (0.8 mm; IQR, 0.1 to 1.0 mm; P = .03) compared with the osteotomized shoulder. The glenoid depth of the repair was less than the baseline value (P = .01). Repair of an anterior bony Bankart lesion equivalent to 19% of the glenoid length with 3 suture anchors restored the peak translational force needed to anteriorly displace the humerus relative to the glenoid; however, this technique failed to restore the natural glenoid depth in a laboratory setting. Our findings describe the inability of a single-row suture anchor repair to provide anatomic fixation of the bony Bankart lesion equivalent to 19% of the glenoid length

Electrochromic mirror using viologen-anchored nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Kim, Han Na [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); University of Science and Technology, Advanced Device Technology, 217 Gajeong-roYuseong-gu, Daejeon 305-350 (Korea, Republic of); Cho, Seong M.; Ah, Chil Seong; Song, Juhee; Ryu, Hojun; Kim, Yong Hae [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); Kim, Tae-Youb, E-mail: youby@etri.re.kr [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); University of Science and Technology, Advanced Device Technology, 217 Gajeong-roYuseong-gu, Daejeon 305-350 (Korea, Republic of)

2016-10-15

Highlights: • Three types of ECM device were fabricated using viologen-anchored ECDs. • The devices were investigated according to their optical structures. • The anti-reflection material affects the reflectance and the coloration efficiency. • The device design of ECMs is a crucial factor for clear reflected images. - Abstract: Electrochromic mirrors (ECMs) that are used in automobile mirrors need to have high reflectance, a high contrast ratio, and a clear image. In particular, it is critical that distortions of clear images are minimized for safety. Therefore, an ECM is fabricated using viologen-anchored nanoparticles and a magnesium fluoride (MgF{sub 2}) layer with an anti-reflection function. The ECM has approximately 30.42% in the reflectance dynamic range and 125 cm{sup 2}/C high coloration efficiency.

Uncertainty assessment of a dike with an anchored sheet pile wall using FEM

Directory of Open Access Journals (Sweden)

Rippi Aikaterini

2016-01-01

Full Text Available The Dutch design codes for the dikes with retaining walls rely on Finite Element Analysis (FEM in combination with partial safety factors. However, this can lead to conservative designs. For this reason, in this study, a reliability analysis is carried out with FEM calculations aiming to demonstrate the feasibility of reliability analysis for a dike with an anchored sheet pile wall modelled in the 2D FEM, Plaxis. Sensitivity and reliability analyses were carried out and enabled by coupling the uncertainty package, OpenTURNS and Plaxis. The most relevant (ultimate limit states concern the anchor, the sheet pile wall, the soil body failure (global instability and finally the system. The case was used to investigate the applicability of the First Order Reliability Method (FORM and Directional Sampling (DS to analysing these limit states. The final goal is to estimate the probability of failure and identify the most important soil properties that affect the behaviour of each component and the system as a whole. The results of this research can be used to assess and optimize the current design procedure for dikes with retaining walls.

Comprehensive evaluation of Streptococcus sanguinis cell wall-anchored proteins in early infective endocarditis.

Science.gov (United States)

Turner, Lauren Senty; Kanamoto, Taisei; Unoki, Takeshi; Munro, Cindy L; Wu, Hui; Kitten, Todd

2009-11-01

Streptococcus sanguinis is a member of the viridans group of streptococci and a leading cause of the life-threatening endovascular disease infective endocarditis. Initial contact with the cardiac infection site is likely mediated by S. sanguinis surface proteins. In an attempt to identify the proteins required for this crucial step in pathogenesis, we searched for surface-exposed, cell wall-anchored proteins encoded by S. sanguinis and then used a targeted signature-tagged mutagenesis (STM) approach to evaluate their contributions to virulence. Thirty-three predicted cell wall-anchored proteins were identified-a number much larger than those found in related species. The requirement of each cell wall-anchored protein for infective endocarditis was assessed in the rabbit model. It was found that no single cell wall-anchored protein was essential for the development of early infective endocarditis. STM screening was also employed for the evaluation of three predicted sortase transpeptidase enzymes, which mediate the cell surface presentation of cell wall-anchored proteins. The sortase A mutant exhibited a modest (approximately 2-fold) reduction in competitiveness, while the other two sortase mutants were indistinguishable from the parental strain. The combined results suggest that while cell wall-anchored proteins may play a role in S. sanguinis infective endocarditis, strategies designed to interfere with individual cell wall-anchored proteins or sortases would not be effective for disease prevention.

Inflation targeting and the anchoring of inflation expectations in the CEE countries

Directory of Open Access Journals (Sweden)

Nedeljković Milan

2017-01-01

Full Text Available This paper studies the time evolution in the degree and level of anchoring of inflation expectations in four Central and Eastern European inflation targeting countries. The results suggest that the degree of anchoring of inflation expectations increased gradually in all countries over the last decade, while the level of implied inflation targets moved towards the official target. The extent of anchoring increased more strongly in the first years following the IT adoption and more gradually over the later period. We also find that smooth changes of the official target had a positive impact on anchoring. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 47028: Advancing Serbia’s Competitiveness in the Process of EU Accession

Reduction of lateral loads in abutments using ground anchors

OpenAIRE

Laefer, Debra F.; Truong-Hong, Linh; Le, Khanh Ba

2013-01-01

In bridge design, economically addressing large, lateral earth pressures on bridge abutments is a major challenge. Traditional approaches employ enlargement of the abutment components to resist these pressures. This approach results in higher construction costs. As an alternative, a formal approach using ground anchors to resist lateral soil pressure on bridge abutments is proposed herein. The ground anchors are designed to minimise lateral forces at the pile cap base. Design examples for hig...

The Effect of Suture Anchor Insertion Angle on Calcaneus Pullout Strength: Challenging the Deadman's Angle.

Science.gov (United States)

Weiss, William M; Saucedo, Ramon P; Robinson, John D; Lo, Chung-Chieh Jason; Morris, Randal P; Panchbhavi, Vinod K

2017-10-01

Refractory cases of Achilles tendinopathy amenable to surgery may include reattachment of the tendon using suture anchors. However, there is paucity of information describing the optimal insertion angle to maximize the tendon footprint and anchor stability in the calcaneus. The purpose of this investigation is to compare the fixation strength of suture anchors inserted at 90° and 45° (the Deadman's angle) relative to the primary compressive trabeculae of the calcaneus. A total of 12 matched pairs of adult cadaveric calcanei were excised and potted to approximate their alignment in vivo. Each pair was implanted with 5.5-mm bioabsorbable suture anchors placed either perpendicular (90°) or oblique (45°) to the primary compressive trabeculae. A tensile load was applied until failure of anchor fixation. Differences in failure load and stiffness between anchor fixation angles were determined by paired t-tests. No significant differences were detected between perpendicular and oblique suture anchor insertion relative to primary compressive trabeculae in terms of load to failure or stiffness. This investigation suggests that the fixation strength of suture anchors inserted perpendicular to the primary compression trabeculae and at the Deadman's angle are possibly comparable. Biomechanical comparison study.

Stone anchors from Sindhudurg Fort on the west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.; Gaur, A.S.

, of which there are triangular and three grapnet-type, used to construct the jetty along with the locally available sand stone. The two remaining grapnet-type anchors are erected on the jetty for mooring purposes. It is found that none of the anchors were...

Composite materials formed with anchored nanostructures

Science.gov (United States)

Seals, Roland D; Menchhofer, Paul A; Howe, Jane Y; Wang, Wei

2015-03-10

A method of forming nano-structure composite materials that have a binder material and a nanostructure fiber material is described. A precursor material may be formed using a mixture of at least one metal powder and anchored nanostructure materials. The metal powder mixture may be (a) Ni powder and (b) NiAl powder. The anchored nanostructure materials may comprise (i) NiAl powder as a support material and (ii) carbon nanotubes attached to nanoparticles adjacent to a surface of the support material. The process of forming nano-structure composite materials typically involves sintering the mixture under vacuum in a die. When Ni and NiAl are used in the metal powder mixture Ni.sub.3Al may form as the binder material after sintering. The mixture is sintered until it consolidates to form the nano-structure composite material.

Morphometric quantification of biodegradable PLDLLA-anchor implant-beds on magnetic resonance images of the humeral head

International Nuclear Information System (INIS)

Chatterjee, D.

2009-01-01

An overview of the functional anatomy of the human shoulder joint is the base for understanding of rotator cuff tears and its surgical repair by means of suture anchors. These anchors, manufactured of biodegradable polymers, do not (or not totally) degrade in the period of time postulated by the manufactures. Bone healing seems to be impaired. Radiological follow-ups of 8 months to years postoperative revealed osteolysis and even cystic deformation of the implant beds (=anchor-holes). In this present study the anchor-holes are morphometrically measured for the first time on MRT-images. For this prospective study MRIs from altogether 38 patients (20 female/18 male, age 43.9a - 81.6a) were selected after arthroscopic rotator cuff repair with 1-4 biodegradable suture anchors (PLDLLA 'Bio-Corkscrews', Arthrex Inc., Naples FL, USA) at a single institution. After signing an informed consent form patients' MRIs could be evaluated after a mean follow-up period of 15.8 and 36 months. The shapes of the bony implant beds were subjectively categorized and for the computer-assisted morphometry of the anchor-hole areas Adobe Photoshop; CS3 Extended (Version 10.0) was used and adapted. The results were statistically analyzed and correlated with the clinical success rate (Constant Score=CS). All anchor-holes were discernable for up to 42 months. A significant shift of threaded to cylindric anchor-hole shapes was evident from the 1 st to 2 nd follow-up. Only 11.5% of the anchor-holes showed a cystic enlargement. At the 1 st follow-up the anchor-hole areas increased on average by 50.87% compared to original anchor size. However, at the 2 nd follow-up all anchor-hole areas decreased significantly (p st follow-up. The average preoperative CS improved from 38.5 points to 87.4 (1 st follow-up) and then remained at 87 points (2 nd follow-up). Anchor-holes of biodegradable suture anchor are, as opposed to the time period claimed by the manufacturers, visible and thus not totally degraded

Chemical biology of Glycosylphosphatidylinositol (GPI) anchors

Indian Academy of Sciences (India)

Admin

CSIR-IIIM. Chemical biology of. Glycosylphosphatidylinositol (GPI) anchors. Ram Vishwakarma. CSIR-Indian Institute of Integrative Medicine, Jammu. N ti l I tit t f I l. N. D lhi. National Institute of Immunology, New Delhi. Piramal Life Sciences Ltd, Mumbai ...

Characterizing the flow of stirred vessels with anchor type impellers

Directory of Open Access Journals (Sweden)

S.M.C. Peixoto

2000-12-01

Full Text Available Despite its importance in chemical industries, there are few works which studies anchor type impellers and only a fraction of the works investigate these systems under a computational approach. The great majority refers to turbine impellers, specially Rushton turbines, under turbulent flow. Anchor impellers are used specially for highly viscous flow, typical of polymer reactions. The viscosity is normally in the range 1000-10000 cp. Since this range of viscosity describe highly viscous flows, the reactions for anchor agitated systems are normally carried out under laminar flow. This work presents a detailed computational fluid dynamics (CFD approach to study the behaviour of stirred vessels using anchor impellers. The axial plane of the tank, which is being modelled, is divided into small control volumes, which collectively is referred to as the mesh, or grid. In each of these cells the momentum balance, energy and mass conservation, which describes the model, are rewritten algebraically using the finite volumes method to relate such variables as velocity, pressure and temperature to values in neighbouring cells. The equations are then solved numerically, and the results yield the flow corresponding to the model. Since the geometry of a vessel with anchor impellers strictly calls for a three dimensional method, an approximation is made to account for the effect of the blades (Kuncewics, 1992. The main objective of this work is to give a detailed description of the flow generated by this axial impeller with a view to indicate ways in which the design and operation of these systems can be improved.

Model for ion confinement in a hot-electron tandem mirror anchor

International Nuclear Information System (INIS)

Baldwin, D.E.

1980-01-01

Anisotropic, hot electrons trapped in local minimum-B wells have been proposed as MHD-stabilizing anchors to an otherwise axisymmetric tandem configuration. This work describes a model for plasma confinement between the anchors and the remainder of the system and calcuates the power loss implied by maintenance of this plasma

Bioabsorbable Suture Anchor Migration to the Acromioclavicular Joint: How Far Can These Implants Go?

Directory of Open Access Journals (Sweden)

Giovanna Medina

2014-01-01

Full Text Available Few complications regarding the use of bioabsorbable suture anchors in the shoulder have been reported. What motivated this case report was the unusual location of the anchor, found in the acromioclavicular joint which, to our knowledge, has never been reported so far. A 53-year old male with previous rotator cuff (RC repair using bioabsorbable suture anchors presented with pain and weakness after 2 years of surgery. A suspicion of retear of the RC led to request of a magnetic resonance image, in which the implant was found located in the acromioclavicular joint. The complications reported with the use of metallic implants around the shoulder led to the development of bioabsorbable anchors. Advantages are their absorption over time, minimizing the risk of migration or interference with revision surgery, less artifacts with magnetic resonance imaging, and tendon-to-bone repair strength similar to metallic anchors. Since the use of bioabsorbable suture anchors is increasing, it is important to know the possible complications associated with these devices.

Evolutionary morphology in shape and size of haptoral anchors in 14 Ligophorus spp. (Monogenea: Dactylogyridae).

Science.gov (United States)

Rodríguez-González, Abril; Sarabeev, Volodimir; Balbuena, Juan Antonio

2017-01-01

The search for phylogenetic signal in morphological traits using geometric morphometrics represents a powerful approach to estimate the relative weights of convergence and shared evolutionary history in shaping organismal form. We assessed phylogenetic signal in the form of ventral and dorsal haptoral anchors of 14 species of Ligophorus occurring on grey mullets (Osteichthyes: Mugilidae) from the Mediterranean, the Black Sea and the Sea of Azov. The phylogenetic relationships among these species were mapped onto the morphospaces of shape and size of dorsal and ventral anchors and two different tests were applied to establish whether the spatial positions in the morphospace were dictated by chance. Overall significant phylogenetic signal was found in the data. Allometric effects on anchor shape were moderate or non-significant in the case of evolutionary allometry. Relatively phylogenetically distant species occurring on the same host differed markedly in anchor morphology indicating little influence of host species on anchor form. Our results suggest that common descent and shared evolutionary history play a major role in determining the shape and, to a lesser degree in the size of haptoral anchors in Ligophorus spp. The present approach allowed tracing paths of morphological evolution in anchor shape. Species with narrow anchors and long shafts were associated predominately with Liza saliens. This morphology was considered to be ancestral relative to anchors of species occurring on Liza haematocheila and M. cephalus possessing shorter shafts and longer roots. Evidence for phylogenetic signal was more compelling for the ventral anchors, than for the dorsal ones, which could reflect different functional roles in attachment to the gills. Although phylogeny and homoplasy may act differently in other monogeneans, the present study delivers a common framework to address effectively the relationships among morphology, phylogeny and other traits, such as host specificity

Evolutionary morphology in shape and size of haptoral anchors in 14 Ligophorus spp. (Monogenea: Dactylogyridae.

Directory of Open Access Journals (Sweden)

Abril Rodríguez-González

Full Text Available The search for phylogenetic signal in morphological traits using geometric morphometrics represents a powerful approach to estimate the relative weights of convergence and shared evolutionary history in shaping organismal form. We assessed phylogenetic signal in the form of ventral and dorsal haptoral anchors of 14 species of Ligophorus occurring on grey mullets (Osteichthyes: Mugilidae from the Mediterranean, the Black Sea and the Sea of Azov. The phylogenetic relationships among these species were mapped onto the morphospaces of shape and size of dorsal and ventral anchors and two different tests were applied to establish whether the spatial positions in the morphospace were dictated by chance. Overall significant phylogenetic signal was found in the data. Allometric effects on anchor shape were moderate or non-significant in the case of evolutionary allometry. Relatively phylogenetically distant species occurring on the same host differed markedly in anchor morphology indicating little influence of host species on anchor form. Our results suggest that common descent and shared evolutionary history play a major role in determining the shape and, to a lesser degree in the size of haptoral anchors in Ligophorus spp. The present approach allowed tracing paths of morphological evolution in anchor shape. Species with narrow anchors and long shafts were associated predominately with Liza saliens. This morphology was considered to be ancestral relative to anchors of species occurring on Liza haematocheila and M. cephalus possessing shorter shafts and longer roots. Evidence for phylogenetic signal was more compelling for the ventral anchors, than for the dorsal ones, which could reflect different functional roles in attachment to the gills. Although phylogeny and homoplasy may act differently in other monogeneans, the present study delivers a common framework to address effectively the relationships among morphology, phylogeny and other traits, such

Conceptual design of cooling anchor for current lead on HTS field coils

Energy Technology Data Exchange (ETDEWEB)

Hyeon, C. J.; Kim, J. H.; Quach, H. L. [Dept. of Electrical Engineering, Jeju National University, Jeju (Korea, Republic of); and others

2017-06-15

The role of current lead in high-temperature superconducting synchronous machine (HTSSM) is to function as a power supply by connecting the power supply unit at room temperature with the HTS field coils at cryogenic temperature. Such physical and electrical connection causes conduction and Joule-heating losses, which are major thermal losses of HTSSM rotors. To ensure definite stability and economic feasibility of HTS field coils, quickly and smoothly cooling down the current lead is a key design technology. Therefore, in this paper, we introduce a novel concept of a cooling anchor to enhance the cooling performance of a metal current lead. The technical concept of this technology is the simultaneously chilling and supporting the current lead. First, the structure of the current lead and cooling anchor were conceptually designed for field coils for a 1.5 MW-class HTSSM. Then, the effect of this installation on the thermal characteristics of HTS coils was investigated by 3D finite element analysis.

Experimental Study On Lateral Load Capacity of Bamboo RC Beam Column Joints Strengthened By Bamboo Mechanical Anchors

Directory of Open Access Journals (Sweden)

Sri Umniati B.

2017-01-01

Full Text Available In this paper, the prospective of bamboos which available abundantly especially in Indonesia as rebars and mechanical anchors are studied. And also the endurance of the bamboos mechanical anchors to withstand cyclic loading were observed. Nine classes of bamboos bar were evaluated: consist of 3 different anchors (0, 4 and 8 anchors and 3 different compressive strength (19.19 MPa, 29.61 MPa and 37.96 MPa means 3 × 3 parameters. The results show that the lateral load capacity increased significantly with the present of bamboo anchors specimens: 26.04 % for 4 anchors specimens (C2 and 25 % for the 8 anchors specimens (C3 compared to zero anchor specimens (C1. On the other hand, the compressive strength of concrete have no significant effects to the lateral load capacity. Overall it can be concluded that, bamboo can be used as mechanical anchorage to strengthen beam column joint.

Data for identification of GPI-anchored peptides and ω-sites in cancer cell lines

Directory of Open Access Journals (Sweden)

Yusuke Masuishi

2016-06-01

Full Text Available We present data obtained using a focused proteomics approach to identify the glycosylphosphatidylinositol (GPI-anchored peptides in 19 human cancer cell lines. GPI-anchored proteins (GPI-APs, which localize to the outer leaflet of the membrane microdomains commonly referred to as lipid rafts play important roles in diverse biological processes. Due to the complex structure of the GPI-anchor moiety, it has been difficult to identify GPI-anchored peptide sequences on the proteomic scale by database searches using tools such as MASCOT. Here we provide data from 73 ω-sites derived from 49 GPI-APs in 19 human cancer cell lines. This article contains data related to the research article entitled “Identification of glycosylphosphatidylinositol-anchored proteins and ω-sites using TiO2-based affinity purification followed by hydrogen fluoride treatment” (Masuishi et al., 2016 [1].

Construction and performance of a permanent earth anchor (tieback) system for the Stanford Linear Collider

International Nuclear Information System (INIS)

Obergfell, M.N.

1987-02-01

The Stanford Linear Collider is the newest addition to the high-energy physics research complex at the Stanford Linear Accelerator Center. One of the many unique features of this project is the large, underground pit, where massive particle detectors will study the collision of subatomic particles. The large, open pit utilizes nearly 600 permanent earth anchors (tiebacks) for the support of the 56 ft (17 m) high walls, and is one of the largest applications of tiebacks for permanent support of a structure. This paper examines the use of tiebacks on this project with emphasis on their installation and performance

Comprehensive Evaluation of Streptococcus sanguinis Cell Wall-Anchored Proteins in Early Infective Endocarditis▿ †

Science.gov (United States)

Turner, Lauren Senty; Kanamoto, Taisei; Unoki, Takeshi; Munro, Cindy L.; Wu, Hui; Kitten, Todd

2009-01-01

Streptococcus sanguinis is a member of the viridans group of streptococci and a leading cause of the life-threatening endovascular disease infective endocarditis. Initial contact with the cardiac infection site is likely mediated by S. sanguinis surface proteins. In an attempt to identify the proteins required for this crucial step in pathogenesis, we searched for surface-exposed, cell wall-anchored proteins encoded by S. sanguinis and then used a targeted signature-tagged mutagenesis (STM) approach to evaluate their contributions to virulence. Thirty-three predicted cell wall-anchored proteins were identified—a number much larger than those found in related species. The requirement of each cell wall-anchored protein for infective endocarditis was assessed in the rabbit model. It was found that no single cell wall-anchored protein was essential for the development of early infective endocarditis. STM screening was also employed for the evaluation of three predicted sortase transpeptidase enzymes, which mediate the cell surface presentation of cell wall-anchored proteins. The sortase A mutant exhibited a modest (∼2-fold) reduction in competitiveness, while the other two sortase mutants were indistinguishable from the parental strain. The combined results suggest that while cell wall-anchored proteins may play a role in S. sanguinis infective endocarditis, strategies designed to interfere with individual cell wall-anchored proteins or sortases would not be effective for disease prevention. PMID:19703977

Career anchors and career resilience: Supplementary constructs?

Directory of Open Access Journals (Sweden)

L. J. Van Vuuren

2000-06-01

Full Text Available Previously the authors reported on a study in which an attempt was made at defining and measuring the construct career resilience (Fourie & Van Vuuren, 1998. The present article continues this investigation by reporting on the relationship between career resilience and career anchors, as defined in Scheins (1975; 1978; 1990; 1992 career anchor model. The aim of the study was to determine whether career anchor patterning could potentially inhibit or facilitate individuals' levels of career resilience. The "Career Resilience Questionnaire" (CRQ (Fourie & Van Vuuren, 1998 together with Scheins (1990 "Career Orientations Inventory" (COI were administered to 352 skilled employees. The findings regarding the statistical relationship between the two constructs are discussed. Opsomming Loopbaanankers en loopbaangehardheid: supplementere konstrukte? In n vorige publikasie van Fourie en Van Vuuren (1998 is die bevindinge aangaande die afbakening en meting van die konstruk, loopbaangehardheid, gerapporteer. In die huidige artikel word die ondersoek voortgesit met 'n beskrywing van die verwantskap tussen loopbaangehardheid en loopbaanankers, soos gedefinieer in die loopbaanankermodel van Schein (1975; 1978; 1990; 1992. Die doel met die studie was om te bepaal of die mate van loopbaanankerontplooiing individuele vlakke van loopbaangehardheid potensieel fasiliteer ofinhibeer. Die "Career Resilience Questionnaire" (CRQ (Fourie & Van Vuuren, 1998 is tesame met die "Career Orientation Inventory" (COI (Schein, 1990 op 352 geskoolde werknemers geadministreer. Die bevindinge betreffende die statistiese verwantskap tussen die twee konstrukte word bespreek.

Arthroscopic suture anchor repair of the lateral ligament ankle complex: a cadaveric study.

Science.gov (United States)

Giza, Eric; Shin, Edward C; Wong, Stephanie E; Acevedo, Jorge I; Mangone, Peter G; Olson, Kirstina; Anderson, Matthew J

2013-11-01

Operative treatment of mechanical ankle instability is indicated for patients with multiple sprains and continued episodes of instability. Open repair of the lateral ankle ligaments involves exposure of the attenuated ligaments and advancement back to their anatomic insertions on the fibula using bone tunnels or suture implants. Open and arthroscopic fixation are equal in strength to failure for anatomic Broström repair. Controlled laboratory study. Seven matched pairs of human cadaveric ankle specimens were randomized into 2 groups of anatomic Broström repair: open or arthroscopic. The calcaneofibular ligament and anterior talofibular ligament were excised from their origin on the fibula. In the open repair group, 2 suture anchors were used to reattach the ligaments to their anatomic origins. In the arthroscopic repair group, identical suture anchors were used for repair via an arthroscopic technique. The ligaments were cyclically loaded 20 times and then tested to failure. Torque to failure, degrees to failure, initial stiffness, and working stiffness were measured. A matched-pair analysis was performed. Power analysis of 0.8 demonstrated that 7 pairs needed to show a difference of 30%, with a 15% standard error at a significance level of α = .05. There was no difference in the degrees to failure, torque to failure, or stiffness for the repaired ligament complex. Nine of 14 specimens failed at the suture anchor. There is no statistical difference in strength or stiffness of a traditional open repair as compared with an arthroscopic anatomic repair of the lateral ligaments of the ankle. An arthroscopic technique can be considered for lateral ligament stabilization in patients with mild to moderate mechanical instability.

Ultraweak azimuthal anchoring of a nematic liquid crystal on a planar orienting photopolymer

International Nuclear Information System (INIS)

Nespoulous, Mathieu; Blanc, Christophe; Nobili, Maurizio

2007-01-01

The search of weak anchoring is an important issue for a whole class of liquid crystal displays. In this paper we present an orienting layer showing unreached weak planar azimuthal anchoring for 4-n-pentyl-4 ' -cyanobiphenyl nematic liquid crystal (5CB). Azimuthal extrapolation lengths as large as 80 μm are easily obtained. Our layers are made with the commercial photocurable polymer Norland optical adhesive 60. The anisotropy of the film is induced by the adsorption of oriented liquid crystal molecules under a 2 T magnetic field applied parallel to the surfaces. We use the width of surface π-walls and a high-field electro-optical method to measure, respectively, the azimuthal and the zenithal anchorings. The azimuthal anchoring is extremely sensitive to the ultraviolet (UV) dose and it also depends on the magnetic field application duration. On the opposite, the zenithal anchoring is only slightly sensitive to the preparation parameters. All these results are discussed in terms of the adsorption/desorption mechanisms of the liquid crystal molecules on the polymer layer and of the flexibility of the polymer network

Factors related to furniture anchoring: a method for reducing harm during earthquakes.

Science.gov (United States)

Haraoka, Tomoko; Hayasaka, Shinya; Murata, Chiyoe; Yamaoka, Taiji; Ojima, Toshiyuki

2013-02-01

Fatalities and injuries during an earthquake can be reduced by taking preemptive measures before-hand, and furniture anchoring is an important safety measure for all residents. This study sought to clarify the factors associated with furniture anchoring within the home. A self-administered mail survey was completed from July to August 2010 by 3500 men and women between the ages of 20 and 69 years who were chosen at random from an official government resident registry of 2 cities in Japan. Of the 1729 valid responses, 37.1% reported furniture anchoring. An association with furniture anchoring was observed for having viewed earthquake intensity maps or damage predictions (odds ratio [OR] 1.92, 95% C1 1.54-2.39), expressing concern about a future earthquake (OR 2.07, 95% C1 1.36-3.15), feelings of urgency (OR 1.90, 95% CI 1.47-2.45), accuracy of the government disaster preparedness information (OR 1.68, 95% CI 1.17-2.42), knowledge of the meaning of emergency earthquake warnings (OR 1.67, 95% CI 1.12-2.48), and participation in voluntary disaster preparedness activities (OR 1.40, 95% C1 1.12-1.75). Furniture anchoring was found to be associated with risk awareness, risk perception, disaster preparedness information provided by government to residents, knowledge of earthquakes, participation in voluntary disaster preparedness activities, nonwooden structures, and marital status. An increase in furniture anchoring is important and can be achieved through education and training in daily life.

Career Anchors: Distribution and Impact on Job Satisfaction, the Israeli Case

Science.gov (United States)

Danziger, Nira; Valency, Rony

2006-01-01

Purpose: The purpose of this paper is to examine the career anchor concept developed by Edgar Schein. Design/methodology/approach: The paper focuses on the distribution of the eight career anchors, on a large heterogeneous sample and the differences in the distribution by gender and type of employment; and the impact of the congruence on job…

A reusable suture anchor for arthroscopy psychomotor skills training.

Science.gov (United States)

Tillett, Edward D; Rogers, Rainie; Nyland, John

2003-03-01

For residents to adequately develop the early arthroscopy psychomotor skills required to better learn how to manage the improvisational situations they will encounter during actual patient cases, they need to experience sufficient practice repetitions within a contextually relevant environment. Unfortunately, the cost of suture anchors can be a practice repetition-limiting factor in learning arthroscopic knot-tying techniques. We describe a technique for creating inexpensive reusable suture anchors and provide an example of their application to repair the anterior glenoid labrum during an arthroscopy psychomotor skills laboratory training session.

JOB SATISFACTION AND CAREER CHOICES: A STUDY USING SCHEIN´S CAREER ANCHOR MODEL

OpenAIRE

Codaro, Rosana Silvina; Tomei, Patricia Amelia; Serra, Bernardo Paraiso de Campos

2017-01-01

This study explores the relationship between job satisfaction and alignment between the individual´s current occupation and his/her talents, needs and values, namely as career anchors. A quantitative survey using Schein e Van Maanen´s Career Anchor model (2013) and Siqueira´s Job Satisfaction survey (2008) was performed for a non-probabilistic sample students at the Business School of a private University in Rio de Janeiro. The most frequent career anchor found for both genders was Lifestyle,...

Testing Anchoring effect in CV Data from Dichotomous Choice with a Follow-up Questioning

Energy Technology Data Exchange (ETDEWEB)

Shin, Young Cheol [Dae-Jin University, Pocheon (Korea)

1998-09-01

A questionnaire of dual bisected selection of CVM, which is an induced approach of intended payment, was suggested to overcome statistical inefficiency of a questionnaire of single bisected selection. In spite of several advantages of it, it is doubted that there would be an occurrence of anchoring effect, which is a psychological source of convenient starting point. Therefore, the general intended payment model, which can review the anchoring effect from CV questionnaire of dual bisected selection, was suggested and a mechanism that can review the anchoring effect from the model. This model is combining the dual variation model by Cameron and Quiggin (1994) with the results of bisected selective responses of a firstly presented particular amount as an explanatory variable of the second interior intended payment amount. If the sign of coefficient of the results of bisected selective responses of a firstly presented particular amount was negative and statistically significant, then it can be said that there is an anchoring effect. However, when there is uncertainty of occurrence of anchoring effect from the coefficient review, there is no need to worry about the anchoring effect if the average of estimated values of intended payment amount from two responses were different. As a result of applying this model and mechanism to CV materials on the improvement of water quality of the Han River, there is no need to worry about the anchoring effect. (author). 21 refs., 4 tabs.

Development of a New Nondestructive Inspection Strategy for Corroded Multistrand Anchor Cables

Science.gov (United States)

2016-07-01

parking structures, rock and soil anchors, houses, and many other structures. Figure 1 (left) and (middle) show a typical cable and multistrand anchor...primary tool to identify the ideal propagating modes, the inspection itself is typically carried out in the time domain. The selected tone- burst

Zero-profile anchored cage reduces risk of postoperative dysphagia compared with cage with plate fixation after anterior cervical discectomy and fusion.

Science.gov (United States)

Xiao, ShanWen; Liang, ZhuDe; Wei, Wu; Ning, JinPei

2017-04-01

To compare the rate of postoperative dysphagia between zero-profile anchored cage fixation (ZPC group) and cage with plate fixation (CP group) after anterior cervical discectomy and fusion (ACDF). A meta-analysis of cohort studies between zero-profile anchored cage and conventional cage with plate fixation after ACDF for the treatment of cervical diseases from 2008 to May 2016. An extensive search of studies was performed in PubMed, Medline, Embase, Cochrane library and Google Scholar. Dysphagia rate was extracted. Data analysis was conducted with RevMan 5.2. Sixteen trials involving 1066 patients were included in this meta-analysis. The results suggested that the ZPC group were associated with lower incidences of dysphagia than the CP group at postoperative immediately, 2 weeks, 2, 3, 6 and 12 months. In subgroup analysis, although significant differences were only found in the mild dysphagia at 3 and 6 months postoperatively and in the moderate dysphagia at 2 weeks after surgery; the ZPC group had a lower rate of postoperative dysphagia than the CCP group in short, medium and long term follow-up periods. Zero-profile anchored cage had a lower risk of postoperative dysphagia than cage with plate.

Additional Haptic Information Provided by Anchors Reduces Postural Sway in Young Adults Less Than Does Light Touch

Directory of Open Access Journals (Sweden)

Renato Moraes

2018-06-01

Full Text Available This study investigated the effect of adding haptic information to the control of posture, as well as comparing the effect of both the “light touch” (LT and “anchor system” (AS paradigms on postural sway. Additionally, it compared the effect of location and number of points of contact to the control of posture in young adults. The location consisted of using the anchors tied to the finger and held by the hands, and, for LT, the fingertip. For the number of points of contact, participants used two hands, and then separately the dominant hand, and the non-dominant hand, for both anchor and LT paradigms. Participants stood upright with feet-together and in tandem position while performing tasks that combined the use of anchors and LT, points of contact (hand grip and finger, and number of points of contact (two hands and one hand. In this study, the anchors consist of holding in each hand a flexible cable with the other end attached to the ground. The LT consists of slightly touching a rigid surface with the tip of the index finger. The results showed, first, that the anchors improved postural control less than did the LT. Second, they revealed that holding the anchors with the hands or with them tied to the fingertip resulted in a similar reduction in postural sway only in the tandem position. For the feet-together position, the anchors tied to the fingertip were ineffective. Similarly, the use of one or two hands did not affect the contribution of the anchors. However, using two hands in the LT condition was more effective than was one hand. Third, our results showed the presence of a temporal delay between force and center-of-pressure (COP for the anchors, only in the AP direction with feet-together. In conclusion, overall, the anchors were less effective in reducing postural sway than was the LT. The anchors attached to fingertips were as effective as the hand-held anchors in the tandem position, yet ineffective during foot

Inspection of steel poles; ultrasonic testing of anchor ground rods and cathodic reactions : Corrosion detection : an emerging problem in buried steel structures

Energy Technology Data Exchange (ETDEWEB)

Pandey, A.K.; Randle, R.E.; Stewart, A.H. [EDM International Inc., Fort Collins, CO (United States)

2002-07-01

A typical inspection of steel utility poles routinely overlooks what is below ground, such as anchor rods, stub angles in lattice towers, and direct embedded steel poles. Stub angles are lap or butt spliced to the tower leg and extend several feet below ground line. A case study concerning stub angles (Oberst 1998) is discussed. An inspection of steel poles erected in 1929 revealed that 40 per cent of legs had complete loss of galvanizing, 10 per cent of legs had greater than 10 per cent loss of cross-section, and 2 per cent of legs had greater than 80 per cent loss of cross-section. All corrosion was found within one foot of ground line. A relatively new concept is direct embedded steel poles. An emerging problem concerns tree induced anchor rod corrosion. A corrosion technique for anchor rods was developed and has been commercially available for the past three years. Its effectiveness was verified at the Montana Power Company 500 kV Colstrip Project, where 3 anchor failures were detected in 1995 due to corrosion wastage. The rods are classified as being in good condition up to 10 per cent loss of cross-section, moderate corrosion for losses between 10 and 25 per cent, and excessive corrosion for losses greater than 25 per cent. The results obtained at the Montana Power Company indicated the technique was 98 per cent accurate. The authors discuss the capabilities and limitations of the technique. It was also applied for the Anchor Rod Inspection Project of the Georgia Power Company (GPC). The technique is evaluated in the laboratory, then optimized. Field prototypes are developed, followed by an evaluation at different test sites. figs.

Protein-anchoring therapy to target extracellular matrix proteins to their physiological destinations.

Science.gov (United States)

Ito, Mikako; Ohno, Kinji

2018-02-20

Endplate acetylcholinesterase (AChE) deficiency is a form of congenital myasthenic syndrome (CMS) caused by mutations in COLQ, which encodes collagen Q (ColQ). ColQ is an extracellular matrix (ECM) protein that anchors AChE to the synaptic basal lamina. Biglycan, encoded by BGN, is another ECM protein that binds to the dystrophin-associated protein complex (DAPC) on skeletal muscle, which links the actin cytoskeleton and ECM proteins to stabilize the sarcolemma during repeated muscle contractions. Upregulation of biglycan stabilizes the DPAC. Gene therapy can potentially ameliorate any disease that can be recapitulated in cultured cells. However, the difficulty of tissue-specific and developmental stage-specific regulated expression of transgenes, as well as the difficulty of introducing a transgene into all cells in a specific tissue, prevents us from successfully applying gene therapy to many human diseases. In contrast to intracellular proteins, an ECM protein is anchored to the target tissue via its specific binding affinity for protein(s) expressed on the cell surface within the target tissue. Exploiting this unique feature of ECM proteins, we developed protein-anchoring therapy in which a transgene product expressed even in remote tissues can be delivered and anchored to a target tissue using specific binding signals. We demonstrate the application of protein-anchoring therapy to two disease models. First, intravenous administration of adeno-associated virus (AAV) serotype 8-COLQ to Colq-deficient mice, resulting in specific anchoring of ectopically expressed ColQ-AChE at the NMJ, markedly improved motor functions, synaptic transmission, and the ultrastructure of the neuromuscular junction (NMJ). In the second example, Mdx mice, a model for Duchenne muscular dystrophy, were intravenously injected with AAV8-BGN. The treatment ameliorated motor deficits, mitigated muscle histopathologies, decreased plasma creatine kinase activities, and upregulated expression

Genome-wide divergence and linkage disequilibrium analyses for Capsicum baccatum revealed by genome-anchored single nucleotide polymorphisms

Science.gov (United States)

Principal component analysis (PCA) with 36,621 polymorphic genome-anchored single nucleotide polymorphisms (SNPs) identified collectively for Capsicum annuum and Capsicum baccatum was used to show the distribution of these 2 important incompatible cultivated pepper species. Estimated mean nucleotide...

The detrimental consequences for seagrass of ineffective marine park management related to boat anchoring.

Science.gov (United States)

La Manna, G; Donno, Y; Sarà, G; Ceccherelli, G

2015-01-15

Posidonia oceanica (L.) Delile meadows are recognized as priority habitat for conservation by the EU Habitats Directive. The La Maddalena Archipelago National Park (Mediterranean Sea) P. oceanica meadow, the dominant coastal habitat of the area, is mostly threatened by boat anchoring. 12 years after the establishment of mooring fields and anchoring restrictions, a study was conducted to measure their effectiveness on the conservation of seagrass and the mitigation of anchoring damage. We found that: (i) the condition of P. oceanica was disturbed, both in the mooring fields and in control locations; (ii) mooring fields and anchoring restrictions did not show to be an efficient system for the protection of seagrass, in fact anchor scars increased after the tourist season; (iii) the mooring systems had an impact on the surrounding area of the meadow, probably due to their misuse. On the basis of these results, management recommendations for marine parks are proposed. Copyright © 2014 Elsevier Ltd. All rights reserved.

The Holding Power of Anchors

Indian Academy of Sciences (India)

as the chain begins to drag along the ground; and it also serves, by lying flat on the ground, to keep the palm set at the correct angle as it buries itself. In stockless anchors there are two digging blades set on opposite sides of the shank, and hinged to it by a horizontal hinge which allows them to set themselves at the correct.

Optimal suture anchor direction in arthroscopic lateral ankle ligament repair.

Science.gov (United States)

Yoshimura, Ichiro; Hagio, Tomonobu; Noda, Masahiro; Kanazawa, Kazuki; Minokawa, So; Yamamoto, Takuaki

2017-05-26

In this study, the distance between the insertion point of the suture anchors and posterior surface of the fibula during arthroscopic lateral ankle ligament repair was investigated on computed tomography (CT) images. The hypothesis of this study was that there is an optimal insertional direction of the suture anchor to avoid anchor-related complications. One hundred eleven ankles of 98 patients who had undergone three-dimensional CT scans for foot or ankle disorders without deformity of the fibula were assessed (59 males, 52 females; median age 25.5 years; age range 12-78 years). The shortest distance from the insertion point of the suture anchor to the deepest point of the fossa/top of the convex aspect of the fibula was measured on the axial plane, tilting from the longitudinal axis of the fibula at 90°, 75°, 60°, and 45°. The distance from the insertion point of the suture anchor to the posterior surface of the fibula was also measured in a direction parallel to the sagittal plane of the lateral surface of the talus on the axial plane, tilting from the longitudinal axis of the fibula at 90°, 75°, 60°, and 45°. The posterior fossa was observed in all cases on the 90° and 75° images. The distance from the insertion point to the posterior surface of the fibula in the parallel direction was 15.0 ± 3.4 mm at 90°, 17.5 ± 3.2 mm at 75°, 21.7 ± 3.3 mm at 60°, and 25.7 ± 3.6 mm at 45°. The posterior points in the parallel direction were located on the posterior fossa in 36.0% of cases at 90°, in 12.6% at 75°, and in 0.0% at 60° and 45°. The suture anchor should be directed from anterior to posterior at an angle of <45° to the longitudinal axis of the fibula, parallel to the lateral surface of the talus, to avoid passing through the fibula. Cohort study, Level III.

Anatomic deltoid ligament repair with anchor-to-post suture reinforcement: technique tip.

Science.gov (United States)

Lack, William; Phisitkul, Phinit; Femino, John E

2012-01-01

The deltoid ligament is the primary ligamentous stabilizer of the ankle joint. Both superficial and deep components of the ligament can be disrupted with a rotational ankle fracture, chronic ankle instability, or in late stage adult acquired flatfoot deformity. The role of deltoid ligament repair in these conditions has been limited and its contribution to arthritis is largely unknown. Neglect of the deltoid ligament in the treatment of ankle injuries may be due to difficulties in diagnosis and lack of an effective method for repair. Most acute repair techniques address the superficial deltoid ligament with direct end-to-end repair, fixation through bone tunnels, or suture anchor repair of avulsion injuries. Deep deltoid ligament repair has been described using direct end-to-end repair with sutures, as well as by autograft and allograft tendon reconstruction utilizing various techniques. Newer tenodesis techniques have been described for late reconstruction of both deep and superficial components in patients with stage 4 adult acquired flatfoot deformity. We describe a technique that provides anatomic ligament-to-bone repair of the superficial and deep bundles of the deltoid ligament while reducing the talus toward the medial malleolar facet of the tibiotalar joint with anchor-to-post reinforcement of the ligamentous repair. This technique may protect and allow the horizontally oriented fibers of the deep deltoid ligament to heal with the appropriate resting length while providing immediate stability of the construct.

Quadriceps tendon rupture: a biomechanical comparison of transosseous equivalent double-row suture anchor versus transosseous tunnel repair.

Science.gov (United States)

Hart, Nathan D; Wallace, Matthew K; Scovell, J Field; Krupp, Ryan J; Cook, Chad; Wyland, Douglas J

2012-09-01

Quadriceps rupture off the patella is traditionally repaired by a transosseous tunnel technique, although a single-row suture anchor repair has recently been described. This study biomechanically tested a new transosseous equivalent (TE) double-row suture anchor technique compared with the transosseous repair for quadriceps repair. After simulated quadriceps-patella avulsion in 10 matched cadaveric knees, repairs were completed by either a three tunnel transosseous (TT = 5) or a TE suture anchor (TE = 5) technique. Double-row repairs were done using two 5.5 Bio-Corkscrew FT (fully threaded) (Arthrex, Inc., Naples, FL, USA) and two 3.5 Bio-PushLock anchors (Arthrex, Inc., Naples, FL, USA) with all 10 repairs done with #2 FiberWire suture (Arthrex, Inc., Naples, FL). Cyclic testing from 50 to 250 N for 250 cycles and pull to failure load (1 mm/s) were undertaken. Gap formation and ultimate tensile load (N) were recorded and stiffness data (N/mm) were calculated. Statistical analysis was performed using a Mann-Whitney U test and survival characteristics examined with Kaplan-Meier test. No significant difference was found between the TE and TT groups in stiffness (TE = 134 +/- 15 N/mm, TT = 132 +/- 26 N/mm, p = 0.28). The TE group had significantly less ultimate tensile load (N) compared with the TT group (TE = 447 +/- 86 N, TT = 591 +/- 84 N, p = 0.04), with all failures occurring at the suture eyelets. Although both quadriceps repairs were sufficiently strong, the transosseous repairs were stronger than the TE suture anchor repairs. The repair stiffness and gap formation were similar between the groups.

Career Anchors of United States Air Force Information Systems Workers: A Turnover Predictor

National Research Council Canada - National Science Library

Wynne, Lee

2002-01-01

...) and the work of Schein (1987) to measure the career anchors, job satisfaction, and turnover intention of AF IS workers to determine if those whose job type and career anchor match report higher satisfaction and lower turnover...

Comparison between suture anchor and transosseous suture for the modified-Broström procedure.

Science.gov (United States)

Cho, Byung-Ki; Kim, Yong-Min; Kim, Dong-Soo; Choi, Eui-Sung; Shon, Hyun-Chul; Park, Kyoung-Jin

2012-06-01

This prospective, randomized study was conducted to compare clinical outcomes of the modified Broström procedure using suture anchor or transosseous suture technique for chronic ankle instability. Forty patients were followed for more than 2 years after modified Broström procedure. Twenty procedures using a suture anchor and 20 procedures using a transosseous suture were performed by one surgeon. The clinical evaluation consisted of the Karlsson scale and the Sefton grading system. Talar tilt and anterior talar translation were measured on anterior and varus stress radiographs. The Karlsson scale had improved significantly to 90.8 points in the suture anchor group, and to 89.2 points in the transosseous suture group. According to Sefton grading system, 18 patients (90%) in suture anchor group and 17 patients (85%) in transosseous suture group achieved satisfactory results. The talar tilt angle and anterior talar translation improved significantly to 5.9 degrees and 4.2 mm in suture anchor group, and to 5.4 degrees and 4.1 mm in transosseous suture group, respectively. No significant differences existed in clinical and functional outcomes between the two techniques for ligament reattachment. Both modified Broström procedures using the suture anchor and transosseous suture seem to be effective treatment methods for chronic lateral ankle instability.

Glycosylphosphatidylinositol-anchored proteins are required for cell wall synthesis and morphogenesis in Arabidopsis.

Science.gov (United States)

Gillmor, C Stewart; Lukowitz, Wolfgang; Brininstool, Ginger; Sedbrook, John C; Hamann, Thorsten; Poindexter, Patricia; Somerville, Chris

2005-04-01

Mutations at five loci named PEANUT1-5 (PNT) were identified in a genetic screen for radially swollen embryo mutants. pnt1 cell walls showed decreased crystalline cellulose, increased pectins, and irregular and ectopic deposition of pectins, xyloglucans, and callose. Furthermore, pnt1 pollen is less viable than the wild type, and pnt1 embryos were delayed in morphogenesis and showed defects in shoot and root meristems. The PNT1 gene encodes the Arabidopsis thaliana homolog of mammalian PIG-M, an endoplasmic reticulum-localized mannosyltransferase that is required for synthesis of the glycosylphosphatidylinositol (GPI) anchor. All five pnt mutants showed strongly reduced accumulation of GPI-anchored proteins, suggesting that they all have defects in GPI anchor synthesis. Although the mutants are seedling lethal, pnt1 cells are able to proliferate for a limited time as undifferentiated callus and do not show the massive deposition of ectopic cell wall material seen in pnt1 embryos. The different phenotype of pnt1 cells in embryos and callus suggest a differential requirement for GPI-anchored proteins in cell wall synthesis in these two tissues and points to the importance of GPI anchoring in coordinated multicellular growth.

Anchored LH2 complexes in 2D polarization imaging.

Science.gov (United States)

Tubasum, Sumera; Sakai, Shunsuke; Dewa, Takehisa; Sundström, Villy; Scheblykin, Ivan G; Nango, Mamoru; Pullerits, Tõnu

2013-09-26

Protein is a soft material with inherently large structural disorder. Consequently, the bulk spectroscopies of photosynthetic pigment protein complexes provide averaged information where many details are lost. Here we report spectroscopy of single light-harvesting complexes where fluorescence excitation and detection polarizations are both independently rotated. Two samples of peripheral antenna (LH2) complexes from Rhodopseudomonas acidophila were studied. In one, the complexes were embedded in polyvinyl alcohol (PVA) film; in the other, they were anchored on the glass surface and covered by the PVA film. LH2 contains two rings of pigment molecules-B800 and B850. The B800 excitation polarization properties of the two samples were found to be very similar, indicating that orientation statistics of LH2s are the same in these two very different preparations. At the same time, we found a significant difference in B850 emission polarization statistics. We conclude that the B850 band of the anchored sample is substantially more disordered. We argue that both B800 excitation and B850 emission polarization properties can be explained by the tilt of the anchored LH2s due to the spin-casting of the PVA film on top of the complexes and related shear forces. Due to the tilt, the orientation statistics of two samples become similar. Anchoring is expected to orient the LH2s so that B850 is closer to the substrate. Consequently, the tilt-related strain leads to larger deformation and disorder in B850 than in B800.

Bone suture anchor fixation in the lower extremity: a review of insertion principles and a comparative biomechanical evaluation.

Science.gov (United States)

Scranton, Pierce E; Lawhon, S Michael; McDermott, John E

2005-07-01

Suture anchors have been developed for the fixation of ligaments, capsules, or tendons to bone. These devices have led to improved fixation, smaller incisions, earlier limb mobility, and improved outcomes. They were originally developed for use in shoulder reconstructions but are now used in almost all extremities. In the lower leg they are used in the tibia, the talus, the calcaneus, tarsal bones, and phalanges. Nevertheless, techniques for insertion and mechanisms of failure are not well described. Five suture anchors were studied to determine the pullout strength in four distal cadaver femurs and four proximal cadaver tibias from 55- and 62-year-old males. Eight hundred ninety Newton line was used, testing the anchors to failure with an Instron testing device (Instron, Norwood, MA). The anchor devices were inserted randomly and tested blindly (12 tests per anchor device, 60 tests in all). Two anchors in each group tested failed at low loads. Both types of plastic anchors had failures at the eyelet. Average pullout strength varied from 85.4 to 185.6 N. Insertion techniques are specific for each device, and they must be followed for optimal fixation. In this study, in all five groups of anchors tested two of the 12 anchors in each group failed with minimal force. On the basis of this finding we recommend that, if suture anchor fixation is necessary, at least two anchors should be used. Since there appears to be a percentage of failure in all devices, the second anchor can serve as a backup. It is imperative that surgeons be familiar with the insertion techniques of each device before use.

A group of 20 stone anchors from the waters of Dwarka, on the Gujarat Coast, India

Digital Repository Service at National Institute of Oceanography (India)

Gaur, A.S; Sundaresh; Tripati, S.; Gudigar, P.; Vora, K.H.; Bandodkar, S.N.

A large number of stone anchors were discovered in a water depth of 10-14 m off Dwarka during the 1998-99 season. The seabed near the anchors consists of a ledge with an average height of 1 m. Several anchors were found trapped between the rocks...

Membrane curvature enables N-Ras lipid anchor sorting to liquid-ordered membrane phases

DEFF Research Database (Denmark)

Larsen, Jannik Bruun; Jensen, Martin Borch; Bhatia, Vikram Kjøller

2015-01-01

Trafficking and sorting of membrane-anchored Ras GTPases are regulated by partitioning between distinct membrane domains. Here, in vitro experiments and microscopic molecular theory reveal membrane curvature as a new modulator of N-Ras lipid anchor and palmitoyl chain partitioning. Membrane...

Career Anchors: A New Concept in Career Development for the Professional Educator.

Science.gov (United States)

DeLong, Thomas J.

Created by Dr. Edgar Schein of the Massachusetts Institute of Technology (MIT), the career anchor model suggests that certain motivational/talent/value drives, formed through work experience, function to guide and constrain entire careers; and that such anchors are the source of stability that permits growth and change in other areas. The concept…

The Double-Anchoring Theory of Lightness Perception: A Comment on Bressan (2006)

Science.gov (United States)

Howe, Piers D. L.; Sagreiya, Hersh; Curtis, Dwight L.; Zheng, Chengjie; Livingstone, Margaret S.

2007-01-01

Comments on an article by Bressan. Recently, a double-anchoring theory (DAT) of lightness perception was proposed (P. Bressan, 2006), which offers explanations for all the data explained by the original anchoring theory (A. Gilchrist et al., 1999), as well as a number of additional lightness phenomena. Consequently, DAT can account for an…

An Accessory Protein Required for Anchoring and Assembly of Amyloid Fibers in B. subtilis Biofilms

Science.gov (United States)

Romero, Diego; Vlamakis, Hera; Losick, Richard; Kolter, Roberto

2011-01-01

Cells within Bacillus subtilis biofilms are held in place by an extracellular matrix that contains cell-anchored amyloid fibers, composed of the amyloidogenic protein TasA. As biofilms age they disassemble because the cells release the amyloid fibers. This release appears to be the consequence of incorporation of D-tyrosine, D-leucine, D-tryptophan and D-methionine into the cell wall. Here, we characterize the in vivo roles of an accessory protein TapA (TasA anchoring/assembly protein; previously YqxM) that serves both to anchor the fibers to the cell wall and to assemble TasA into fibers. TapA is found in discrete foci in the cell envelope and these foci disappear when cells are treated with a mixture of D-amino acids. Purified cell wall sacculi retain a functional form of this anchoring protein such that purified fibers can be anchored to the sacculi in vitro. In addition, we show that TapA is essential for the proper assembly of the fibers. Its absence results in a dramatic reduction in TasA levels and what little TasA is left produces only thin fibers that are not anchored to the cell. PMID:21477127

Using Anchoring Vignettes to Adjust Self-Reported Personality: A Comparison Between Countries

Science.gov (United States)

Weiss, Selina; Roberts, Richard D.

2018-01-01

Data from self-report tools cannot be readily compared between cultures due to culturally specific ways of using a response scale. As such, anchoring vignettes have been proposed as a suitable methodology for correcting against this difference. We developed anchoring vignettes for the Big Five Inventory-44 (BFI-44) to supplement its Likert-type response options. Based on two samples (Rwanda: n = 423; Philippines: n = 143), we evaluated the psychometric properties of the measure both before and after applying the anchoring vignette adjustment. Results show that adjusted scores had better measurement properties, including improved reliability and a more orthogonal correlational structure, relative to scores based on the original Likert scale. Correlations of the Big Five Personality Factors with life satisfaction were essentially unchanged after the vignette-adjustment while correlations with counterproductive were noticeably lower. Overall, these changed findings suggest that the use of anchoring vignette methodology improves the cross-cultural comparability of self-reported personality, a finding of potential interest to the field of global workforce research and development as well as educational policymakers. PMID:29593621

Using Anchoring Vignettes to Adjust Self-Reported Personality: A Comparison Between Countries

Directory of Open Access Journals (Sweden)

Selina Weiss

2018-03-01

Full Text Available Data from self-report tools cannot be readily compared between cultures due to culturally specific ways of using a response scale. As such, anchoring vignettes have been proposed as a suitable methodology for correcting against this difference. We developed anchoring vignettes for the Big Five Inventory-44 (BFI-44 to supplement its Likert-type response options. Based on two samples (Rwanda: n = 423; Philippines: n = 143, we evaluated the psychometric properties of the measure both before and after applying the anchoring vignette adjustment. Results show that adjusted scores had better measurement properties, including improved reliability and a more orthogonal correlational structure, relative to scores based on the original Likert scale. Correlations of the Big Five Personality Factors with life satisfaction were essentially unchanged after the vignette-adjustment while correlations with counterproductive were noticeably lower. Overall, these changed findings suggest that the use of anchoring vignette methodology improves the cross-cultural comparability of self-reported personality, a finding of potential interest to the field of global workforce research and development as well as educational policymakers.

Test on the splitting failure capacity of the bottom rail due to uplift in partially anchored shear walls

OpenAIRE

Caprolu, Giuseppe; Girhammar, Ulf Arne; Källsner, Bo; Johnsson, Helena

2012-01-01

Källsner and Girhammar have developed a new plastic design method for wood-frame shear walls at ultimate limit state. The method is capable of calculating the load-carrying capacity of partially anchored shear walls, where the leading stud is not necessarily anchored against uplift. In fully anchored shear walls, the leading stud needs to be anchored using some kind of hold-downs to resist uplift and the bottom rail needs to be fixed by anchor bolts to resist horizontal shear forces. In parti...

Traction endurance biomechanical study of metallic suture anchors at different insertion angles

Directory of Open Access Journals (Sweden)

Azato Flávia Namie

2003-01-01

Full Text Available The suture anchors' insertion angle and its traction resistance are the main subjects of this study. Twenty trials were realized using threaded suture anchors in four diferents angulations (30º /45º /60º /90º in human bone (distal femur and another twenty trials in artificial bone (SawboneTM. The anchors were pulled out being tractioned uprightly from its bone surface by a Kratos Universal test machine. The human bone results found no relation between the main subjects of this study, so whithout statistical value. On the other hand at the artificial bone the insertion angle of 90º beared more traction, being statistically significant compared to the other angles.

Decay accelerating factor of complement is anchored to cells by a C-terminal glycolipid

International Nuclear Information System (INIS)

Medof, M.E.; Walter, E.I.; Roberts, W.L.; Haas, R.; Rosenberry, T.L.

1986-01-01

Membrane-associated decay accelerating factor (DAF) of human erythrocytes (E/sup hu/) was analyzed for a C-terminal glycolipid anchoring structure. Automated amino acid analysis of DAF following reductive radiomethylation revealed ethanolamine and glucosamine residues in proportions identical with those present in the E/sup hu/ acetylcholinesterase (AChE) anchor. Cleavage of radiomethylated 70-kilodalton (kDa) DAF with papain released the labeled ethanolamine and glucosamine and generated 61- and 55-kDa DAF products that retained all labeled Lys and labeled N-terminal Asp. Incubation of intact E/sup hu/ with phosphatidylinositol-specific phospholipase C (PI-PLC), which cleaves the anchors in trypanosome membrane form variant surface glycoproteins (mfVSGs) and murine thymocyte Thy-1 antigen, released 15% of the cell-associated DAF antigen. The released 67-kDa PI-PLC DAF derivative retained its ability to decay the classical C3 convertase C4b2a but was unable to membrane-incorporate and displayed physicochemical properties similar to urine DAF, a hydrophilic DAF form that can be isolated for urine. Nitrous acid deamination cleavage of E/sup hu/ DAF at glucosamine following labeling with the lipophilic photoreagent 3-(trifluoromethyl)-3-(m-[ 125 I]iodophenyl)diazirine ([ 125 I]TID) released the [ 125 I]TID label in a parallel fashion as from [ 125 I]TID-labeled AChE. Biosynthetic labeling of HeLa cells with [ 3 H] ethanolamine resulted in rapid 3 H incorporation into both 48-kDa pro-DAF and 72-kDa mature epithelial cell DAF. The findings indicate that DAF and AChE are anchored in E/sup hu/ by the same or a similar glycolipid structure and that, like VSGs, this structure is incorporated into DAF early in DAF biosynthesis prior to processing of pro-DAF in the Golgi

Strand Tension Control in Anchor Span for Suspension Bridge Using Dynamic Balance Theory

Directory of Open Access Journals (Sweden)

Da Wang

Full Text Available Abstract Strand tension control is essential in suspension bridge safety. However, few quantitative studies have examined the bending rigidity and boundary condition behavior of strands in the anchor span of suspension bridges because of their special structure and complex configuration. In this paper, a new calculation method for strand tension is explored by using dynamic balance theory to determine the effect of bending rigidity and boundary conditions. The accuracy and effectiveness of the proposed method are tested and confirmed with verification examples and application on Nanxi Yangtze Suspension Bridge in China. The results indicated that only low-order frequency calculation could be used to calculate the strand tension without considering the effect of bending rigidity to ensure control accuracy. The influence of bending rigidity on the control precision is related to the tension and the length of the strands, which is significantly determined by the specific value between the stress rigidity and the bending rigidity. The uncertain boundary conditions of the anchor span cable, which are fixed between consolidated and hinged, also have a major effect on the control accuracy. To improve the accuracy of strand tension control, the least squares method is proposed during the tension construction control of the anchor span. This approach can significantly improve the accuracy of the tension control of the main cable strand. Some recommendations for future bridge analysis are provided based on the results of this study.

Experience-based, body-anchored qualitative research interviewing

DEFF Research Database (Denmark)

Stelter, Reinhard

2010-01-01

-anchored interviewing, and second, by an interview guide that explores a research participant's personal experience with mindfulness meditation. An excerpt from an interview is discussed to illustrate the advantages of this interview form, namely its value as a methodological instrument for qualitative research...

Extrusion of bone anchor suture following flexor digitorum profundus tendon avulsion injury repair.

LENUS (Irish Health Repository)

Tiong, William H C

2011-09-01

Flexor digitorum profundus (FDP) zone I tendon avulsion injury is traditionally repaired with a pullout suture technique. More recently, bone anchor sutures have been used as a viable alternative and have largely replaced areas in hand surgery where pullout suture technique was once required. To date, there have been very few complications reported related to bone anchor suture use in FDP tendon reattachment to the bone. We report a very unusual case of extrusion of bone anchor through the nailbed, 6 years after zone I FDP tendon avulsion injury repair and a brief review of literature.

The anchoring mechanism of a bluff-body stabilized laminar premixed flame

KAUST Repository

Kedia, Kushal S.

2014-09-01

The objective of this work is to investigate the mechanism of the laminar premixed flame anchoring near a heat-conducting bluff-body. We use unsteady, fully resolved, two-dimensional simulations with detailed chemical kinetics and species transport for methane-air combustion. No artificial flame anchoring boundary conditions were imposed. Simulations show a shear-layer stabilized flame just downstream of the bluff-body, with a recirculation zone formed by the products of combustion. A steel bluff-body resulted in a slightly larger recirculation zone than a ceramic bluff-body; the size of which grew as the equivalence ratio was decreased. A significant departure from the conventional two-zone flame-structure is shown in the anchoring region. In this region, the reaction zone is associated with a large negative energy convection (directed from products to reactants) resulting in a negative flame-displacement speed. It is shown that the premixed flame anchors at an immediate downstream location near the bluff-body where favorable ignition conditions are established; a region associated with (1) a sufficiently high temperature impacted by the conjugate heat exchange between the heat-conducting bluff-body and the hot reacting flow and (2) a locally maximum stoichiometry characterized by the preferential diffusion effects. © 2014 The Combustion Institute.

Reinforcement mechanism of multi-anchor wall with double wall facing

Science.gov (United States)

Suzuki, Kouta; Kobayashi, Makoto; Miura, Kinya; Konami, Takeharu; Hayashi, Taketo

2017-10-01

The reinforced soil wall has high seismic performance as generally known. However, the seismic behavior has not been clarified accurately yet, especially on multi-anchor wall with double wall facing. Indefinite behavior of reinforced soil wall during earthquake make us complicated in case with adopting to the abutment, because of arrangement of anchor plate as reinforcement often different according to the width of roads. In this study, a series of centrifuge model tests were carried out to investigate the reinforcement mechanism of multi anchor wall with double wall facing from the perspective of the vertical earth pressure. Several types of reinforce arrangement and rigid wall were applied in order to verify the arch function in the reinforced regions. The test results show unique behavior of vertical earth pressure, which was affected by arch action. All the vertical earth pressure placed behind facing panel, are larger than that of middle part between facing panel despite of friction between backfill and facing panel. Similar results were obtained in case using rigid wall. On the other hands, the vertical earth pressure, which were measured at the 3cm high from bottom of model container, shows larger than that of bottom. This results show the existence of arch action between double walls. In addition, it implies that the wall facing of such soil structure confined the backfill as pseudo wall, which is very reason that the multi anchor wall with double wall facing has high seismic performance.

Fullerene-based Anchoring Groups for Molecular Electronics

DEFF Research Database (Denmark)

Martin, Christian A.; Ding, Dapeng; Sørensen, Jakob Kryger

2008-01-01

We present results on a new fullerene-based anchoring group for molecular electronics. Using lithographic mechanically controllable break junctions in vacuum we have determined the conductance and stability of single-molecule junctions of 1,4-bis(fullero[c]pyrrolidin-1-yl)benzene. The compound can...

The Place of White in a World of Grays: A Double-Anchoring Theory of Lightness Perception

Science.gov (United States)

Bressan, Paola

2006-01-01

The specific gray shades in a visual scene can be derived from relative luminance values only when an anchoring rule is followed. The double-anchoring theory I propose in this article, as a development of the anchoring theory of Gilchrist et al. (1999), assumes that any given region (a) belongs to one or more frameworks, created by Gestalt…

Structural models of the membrane anchors of envelope glycoproteins E1 and E2 from pestiviruses

International Nuclear Information System (INIS)

Wang, Jimin; Li, Yue; Modis, Yorgo

2014-01-01

The membrane anchors of viral envelope proteins play essential roles in cell entry. Recent crystal structures of the ectodomain of envelope protein E2 from a pestivirus suggest that E2 belongs to a novel structural class of membrane fusion machinery. Based on geometric constraints from the E2 structures, we generated atomic models of the E1 and E2 membrane anchors using computational approaches. The E1 anchor contains two amphipathic perimembrane helices and one transmembrane helix; the E2 anchor contains a short helical hairpin stabilized in the membrane by an arginine residue, similar to flaviviruses. A pair of histidine residues in the E2 ectodomain may participate in pH sensing. The proposed atomic models point to Cys987 in E2 as the site of disulfide bond linkage with E1 to form E1–E2 heterodimers. The membrane anchor models provide structural constraints for the disulfide bonding pattern and overall backbone conformation of the E1 ectodomain. - Highlights: • Structures of pestivirus E2 proteins impose constraints on E1, E2 membrane anchors. • Atomic models of the E1 and E2 membrane anchors were generated in silico. • A “snorkeling” arginine completes the short helical hairpin in the E2 membrane anchor. • Roles in pH sensing and E1–E2 disulfide bond formation are proposed for E1 residues. • Implications for E1 ectodomain structure and disulfide bonding pattern are discussed

Structural models of the membrane anchors of envelope glycoproteins E1 and E2 from pestiviruses

Energy Technology Data Exchange (ETDEWEB)

Wang, Jimin, E-mail: jimin.wang@yale.edu; Li, Yue; Modis, Yorgo, E-mail: yorgo.modis@yale.edu

2014-04-15

The membrane anchors of viral envelope proteins play essential roles in cell entry. Recent crystal structures of the ectodomain of envelope protein E2 from a pestivirus suggest that E2 belongs to a novel structural class of membrane fusion machinery. Based on geometric constraints from the E2 structures, we generated atomic models of the E1 and E2 membrane anchors using computational approaches. The E1 anchor contains two amphipathic perimembrane helices and one transmembrane helix; the E2 anchor contains a short helical hairpin stabilized in the membrane by an arginine residue, similar to flaviviruses. A pair of histidine residues in the E2 ectodomain may participate in pH sensing. The proposed atomic models point to Cys987 in E2 as the site of disulfide bond linkage with E1 to form E1–E2 heterodimers. The membrane anchor models provide structural constraints for the disulfide bonding pattern and overall backbone conformation of the E1 ectodomain. - Highlights: • Structures of pestivirus E2 proteins impose constraints on E1, E2 membrane anchors. • Atomic models of the E1 and E2 membrane anchors were generated in silico. • A “snorkeling” arginine completes the short helical hairpin in the E2 membrane anchor. • Roles in pH sensing and E1–E2 disulfide bond formation are proposed for E1 residues. • Implications for E1 ectodomain structure and disulfide bonding pattern are discussed.

Two endoplasmic reticulum (ER) membrane proteins that facilitate ER-to-Golgi transport of glycosylphosphatidylinositol-anchored proteins.

Science.gov (United States)

Barz, W P; Walter, P

1999-04-01

Many eukaryotic cell surface proteins are anchored in the lipid bilayer through glycosylphosphatidylinositol (GPI). GPI anchors are covalently attached in the endoplasmic reticulum (ER). The modified proteins are then transported through the secretory pathway to the cell surface. We have identified two genes in Saccharomyces cerevisiae, LAG1 and a novel gene termed DGT1 (for "delayed GPI-anchored protein transport"), encoding structurally related proteins with multiple membrane-spanning domains. Both proteins are localized to the ER, as demonstrated by immunofluorescence microscopy. Deletion of either gene caused no detectable phenotype, whereas lag1Delta dgt1Delta cells displayed growth defects and a significant delay in ER-to-Golgi transport of GPI-anchored proteins, suggesting that LAG1 and DGT1 encode functionally redundant or overlapping proteins. The rate of GPI anchor attachment was not affected, nor was the transport rate of several non-GPI-anchored proteins. Consistent with a role of Lag1p and Dgt1p in GPI-anchored protein transport, lag1Delta dgt1Delta cells deposit abnormal, multilayered cell walls. Both proteins have significant sequence similarity to TRAM, a mammalian membrane protein thought to be involved in protein translocation across the ER membrane. In vivo translocation studies, however, did not detect any defects in protein translocation in lag1Delta dgt1Delta cells, suggesting that neither yeast gene plays a role in this process. Instead, we propose that Lag1p and Dgt1p facilitate efficient ER-to-Golgi transport of GPI-anchored proteins.

Unlocking Hospitality Managers Career Transitions through Applying Schein's Career Anchors Theory

Science.gov (United States)

McGuire, David; Polla, Giovana; Heidl, Britta

2017-01-01

Purpose: This paper seeks to unlock the career transitions of hospitality managers through applying Schein's career anchors theory. It seeks to understand how Schein's Career Anchors help explain the career transitions of managers in the Scottish hospitality industry. Design/methodology/approach: The paper adopts a non-sequential multi-method…

Arthroscopic repair of lateral ankle ligament complex by suture anchor.

Science.gov (United States)

Wang, Jingwei; Hua, Yinghui; Chen, Shiyi; Li, Hongyun; Zhang, Jian; Li, Yunxia

2014-06-01

Arthroscopic repair of the lateral ligament complex with suture anchors is increasingly used to treat chronic ankle instability (CAI). Our aims are (1) to analyze and evaluate the literature on arthroscopic suture anchor repair of the anterior talofibular ligament and (2) to conduct a systematic review of the clinical evidence on the reported outcomes and complications of treating CAI with this technique. We performed a systematic review of the literature using PubMed, Ovid, Elsevier ScienceDirect, Web of Science-Conference Proceedings Citation Index, and the Cochrane Database of Systematic Reviews from 1987 to September 2013. Clinical studies using the arthroscopic suture anchor technique to treat CAI were included. Outcome measures consisted of clinical assessment of postoperative ligament stability and complications. In addition, the methodologic quality of the included studies was assessed by use of the modified Coleman Methodology Score. After reviewing 371 studies, we identified 6 studies (5 retrospective case series and 1 prospective case series, all Level IV) that met the inclusion criteria, with a mean Coleman Methodology Score of 71.8 ± 7.52 (range, 63 to 82). In these studies 178 patients (179 ankles) underwent arthroscopic suture anchor repair of the anterior talofibular ligament with a mean follow-up period of 38.9 months (range, 6 to 117.6 months). All patients were reported to have subjective improvement of their ankle instability, with complications in 31 cases. Studies of arthroscopic suture anchor technique to treat CAI are sparse, with moderate mean methodologic quality. The included studies suggest that the arthroscopic technique is a feasible procedure to restore ankle stability; however, on the basis of our review, this technique seems to be associated with a relatively high complication rate. Extensive cadaveric studies, clinical trials, and comparative studies comparing arthroscopic and open repair should be performed in the future. Level

An accessory protein required for anchoring and assembly of amyloid fibres in B. subtilis biofilms.

Science.gov (United States)

Romero, Diego; Vlamakis, Hera; Losick, Richard; Kolter, Roberto

2011-06-01

Cells within Bacillus subtilis biofilms are held in place by an extracellular matrix that contains cell-anchored amyloid fibres, composed of the amyloidogenic protein TasA. As biofilms age they disassemble because the cells release the amyloid fibres. This release appears to be the consequence of incorporation of D-tyrosine, D-leucine, D-tryptophan and D-methionine into the cell wall. Here, we characterize the in vivo roles of an accessory protein TapA (TasA anchoring/assembly protein; previously YqxM) that serves both to anchor the fibres to the cell wall and to assemble TasA into fibres. TapA is found in discrete foci in the cell envelope and these foci disappear when cells are treated with a mixture of D-amino acids. Purified cell wall sacculi retain a functional form of this anchoring protein such that purified fibres can be anchored to the sacculi in vitro. In addition, we show that TapA is essential for the proper assembly of the fibres. Its absence results in a dramatic reduction in TasA levels and what little TasA is left produces only thin fibres that are not anchored to the cell. © 2011 Blackwell Publishing Ltd.

Arrows as anchors: An analysis of the material features of electric field vector arrows

Science.gov (United States)

Gire, Elizabeth; Price, Edward

2014-12-01

Representations in physics possess both physical and conceptual aspects that are fundamentally intertwined and can interact to support or hinder sense making and computation. We use distributed cognition and the theory of conceptual blending with material anchors to interpret the roles of conceptual and material features of representations in students' use of representations for computation. We focus on the vector-arrows representation of electric fields and describe this representation as a conceptual blend of electric field concepts, physical space, and the material features of the representation (i.e., the physical writing and the surface upon which it is drawn). In this representation, spatial extent (e.g., distance on paper) is used to represent both distances in coordinate space and magnitudes of electric field vectors. In conceptual blending theory, this conflation is described as a clash between the input spaces in the blend. We explore the benefits and drawbacks of this clash, as well as other features of this representation. This analysis is illustrated with examples from clinical problem-solving interviews with upper-division physics majors. We see that while these intermediate physics students make a variety of errors using this representation, they also use the geometric features of the representation to add electric field contributions and to organize the problem situation productively.

Arrows as anchors: An analysis of the material features of electric field vector arrows

Directory of Open Access Journals (Sweden)

Elizabeth Gire

2014-08-01

Full Text Available Representations in physics possess both physical and conceptual aspects that are fundamentally intertwined and can interact to support or hinder sense making and computation. We use distributed cognition and the theory of conceptual blending with material anchors to interpret the roles of conceptual and material features of representations in students’ use of representations for computation. We focus on the vector-arrows representation of electric fields and describe this representation as a conceptual blend of electric field concepts, physical space, and the material features of the representation (i.e., the physical writing and the surface upon which it is drawn. In this representation, spatial extent (e.g., distance on paper is used to represent both distances in coordinate space and magnitudes of electric field vectors. In conceptual blending theory, this conflation is described as a clash between the input spaces in the blend. We explore the benefits and drawbacks of this clash, as well as other features of this representation. This analysis is illustrated with examples from clinical problem-solving interviews with upper-division physics majors. We see that while these intermediate physics students make a variety of errors using this representation, they also use the geometric features of the representation to add electric field contributions and to organize the problem situation productively.

Controlling the Anchoring Effect through Transcranial Direct Current Stimulation (tDCS to the Right Dorsolateral Prefrontal Cortex

Directory of Open Access Journals (Sweden)

Jianbiao Li

2017-06-01

Full Text Available Selective accessibility mechanisms indicate that anchoring effects are results of selective retrieval of working memory. Neuroimaging studies have revealed that the right dorsolateral prefrontal cortex (DLPFC is closely related to memory retrieval and performance. However, no research has investigated the effect of changing the cortical excitability in right DLPFC on anchoring effects. Transcranial direct current stimulation (tDCS can modulate the excitability of the human cerebral cortex, while anodal and cathodal tDCS are postulated to increase or decrease cortical activity, respectively. In this study, we used tDCS to investigate whether effects of increased or decreased right DLPFC excitability influence anchoring effects in willingness to pay (WTP experiments. Ninety participants were first randomly assigned to receive either anodal, cathodal, or sham stimulation of 15 min, then they performed a valuation task regarding WTP. The results showed that anchoring effects were negatively related to activities of right DLPFC: the anodal stimulation diminished anchoring effects while the cathodal stimulation increased anchoring effects. These outcomes provide one of the first instances of neural evidence for the role of the right DLPFC in anchoring effects and support psychological explanations of the selective accessibility mechanisms and cognitive sets.

Anchor-dependent lipofection with non-glycerol based cytofectins containing single 2-hydroxyethyl head groups.

Science.gov (United States)

Venkata Srilakshmi, Gollapudi; Sen, Joyeeta; Chaudhuri, Arabinda; Ramadas, Yerramsetti; Madhusudhana Rao, Nalam

2002-02-15

Detailed structure-activity investigations aimed at probing the anchor chain length dependency for glycerol-based lipofectins have been reported previously. Herein, we report on the first detailed investigation on the anchor-dependent transfection biology of non-glycerol based simple monocationic cytofectins containing single 2-hydroxyethyl head group functionality using 11 new structural analogs of our previously published first generation of non-glycerol based transfection lipids (lipids 1-11). The C-14 and C-16 analogs of DOMHAC (lipids 4 and 5, respectively) were found to be remarkably efficient in transfecting COS-1 cells. In addition, the present anchor-dependency investigation also revealed that the C-14 analog of DOHEMAB (lipid 10) is significantly efficient in transfecting both COS-1 and NIH3T3 cells. Our results also indicate that too strong lipid-DNA interactions might result in weaker transfection for non-glycerol based cationic lipids. In summary, the anchor-dependence investigations presented here convincingly demonstrate that non-glycerol based cationic lipids containing a single hydroxyethyl head group and hydrophobic C-14 or C-16 anchors are promising non-toxic cationic transfection lipids for future use in liposomal gene delivery.

Enhanced Charge Separation Efficiency in Pyridine-Anchored Phthalocyanine-Sensitized Solar Cells by Linker Elongation.

Science.gov (United States)

Ikeuchi, Takuro; Agrawal, Saurabh; Ezoe, Masayuki; Mori, Shogo; Kimura, Mutsumi

2015-11-01

A series of zinc phthalocyanine sensitizers (PcS22-24) having a pyridine anchoring group are designed and synthesized to investigate the structural dependence on performance in dye-sensitized solar cells. The pyridine-anchor zinc phthalocyanine sensitizer PcS23 shows 79 % incident-photon to current-conversion efficiency (IPCE) and 6.1 % energy conversion efficiency, which are comparable with similar phthalocyanine dyes having a carboxylic acid anchoring group. Based on DFT calculations, the high IPCE is attributed with the mixture of an excited-state molecular orbital of the sensitizer and the orbitals of TiO2 . Between pyridine and carboxylic acid anchor dyes, opposite trends are observed in the linker-length dependence of the IPCE. The red-absorbing PcS23 is applied for co-sensitization with a carboxyl-anchor organic dye D131 that has a complementary spectral response. The site-selective adsorption of PcS23 and D131 on the TiO2 surface results in a panchromatic photocurrent response for the whole visible-light region of sun light. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nominal Anchors in the CIS

OpenAIRE

Peter M Keller; Thomas J Richardson

2003-01-01

Monetary policy has become increasingly important in the countries of the Commonwealth of Independent States (CIS) as fiscal adjustment and structural reforms have taken root. Inflation has been brought down to relatively low levels in almost all of these countries, raising the question of what should be the appropriate nominal anchor at this stage. Formally, almost all CIS countries have floating exchange rate regimes, yet in practice they manage their exchange rates very heavily, perhaps be...

Anchoring the landscape: human utilization of the Cerro Gavilán 2 rockshelter, Middle Orinoco, from the Early Holocene to the present

Directory of Open Access Journals (Sweden)

Kay Scaramelli

Full Text Available Abstract Initial archaeological investigations at Cerro Gavilán 2, a rockshelter located in the Bolívar State of Venezuela, reveal evidence for human activity that spans the Early Holocene to the present. This report summarizes the information obtained through surface collection, limited excavation, and documentation of the surface features and rock art in the cave. Accelerator mass spectrometry (AMS 14C analysis established dates from excavated strata that range between 9250 ± 60 BP to 3440 ± 40 BP, and are associated with a unifacial flake technology and charred faunal and floral remains, whereas surface remains span the known ceramic sequence for the area. Rock art corresponds to distinctive superimposed styles that indicate continual repainting of the cave through time, serving to anchor the site to the landscape for multiple societies inhabiting the region. It is suggested that the shelter may have fulfilled different functions over time and a sequence of seasonal residential, ritual, and funerary activities is proposed. The rich cultural context found in Cerro Gavilán 2 contributes to advances in Amazonian archaeology that are redefining our knowledge of early developments and the complexity of human/environmental interactions in tropical America.

Display of GPI-anchored anti-EGFR nanobodies on extracellular vesicles promotes tumour cell targeting

Directory of Open Access Journals (Sweden)

Sander A. A. Kooijmans

2016-03-01

Full Text Available Background: Extracellular vesicles (EVs are attractive candidate drug delivery systems due to their ability to functionally transport biological cargo to recipient cells. However, the apparent lack of target cell specificity of exogenously administered EVs limits their therapeutic applicability. In this study, we propose a novel method to equip EVs with targeting properties, in order to improve their interaction with tumour cells. Methods: EV producing cells were transfected with vectors encoding for anti-epidermal growth factor receptor (EGFR nanobodies, which served as targeting ligands for tumour cells, fused to glycosylphosphatidylinositol (GPI anchor signal peptides derived from decay-accelerating factor (DAF. EVs were isolated using ultrafiltration/size-exclusion liquid chromatography and characterized using western blotting, Nanoparticle Tracking Analysis, and electron microscopy. EV–tumour cell interactions were analyzed under static conditions using flow cytometry and under flow conditions using a live-cell fluorescence microscopy-coupled perfusion system. Results: V analysis showed that GPI-linked nanobodies were successfully displayed on EV surfaces and were highly enriched in EVs compared with parent cells. Display of GPI-linked nanobodies on EVs did not alter general EV characteristics (i.e. morphology, size distribution and protein marker expression, but greatly improved EV binding to tumour cells dependent on EGFR density under static conditions. Moreover, nanobody-displaying EVs showed a significantly improved cell association to EGFR-expressing tumour cells under flow conditions. Conclusions: We show that nanobodies can be anchored on the surface of EVs via GPI, which alters their cell targeting behaviour. Furthermore, this study highlights GPI-anchoring as a new tool in the EV toolbox, which may be applied for EV display of a variety of proteins, such as antibodies, reporter proteins and signaling molecules.

Impingement syndrome of the shoulder following double row suture anchor technique for arthroscopic rotator cuff repair: a case report

Directory of Open Access Journals (Sweden)

Rambani Rohit

2009-06-01

Full Text Available Abstract Introduction Arthroscopic repair of the rotator cuff is a demanding surgery. Accurate placement of anchors is key to success. Case presentation A 38-year-old woman received arthroscopic repair of her rotator cuff using a double row suture anchor technique. Postoperatively, she developed impingement syndrome which resulted from vertical displacement of a suture anchor once the shoulder was mobilised. The anchor was removed eight weeks following initial surgery and the patient had an uneventful recovery. Conclusion Impingement syndrome following arthroscopic repair of the rotator cuffs using double row suture anchor has not been widely reported. This is the first such case where anchoring has resulted in impingement syndrome.

Homogeneously Dispersed Co9S8 Anchored on Nitrogen and Sulfur Co-Doped Carbon Derived from Soybean as Bifunctional Oxygen Electrocatalysts and Supercapacitors.

Science.gov (United States)

Xiao, Zhen; Xiao, Guozheng; Shi, Minhao; Zhu, Ying

2018-05-16

Developing low-cost and highly active multifunctional electrocatalysts to replace noble metal catalysts is crucial for the commercialization of future clean energy technology. Herein, homogeneous Co 9 S 8 nanoparticles anchored on nitrogen and sulfur co-doped porous carbon nanomaterials (CoS@NSCs) are fabricated by pyrolysis of natural soybean treated with cobalt nitrate. The unique porous structures of the soybean are utilized to provide space for the oxidation and complexation reactions for cobalt compounds, thus leading to in situ generation of homogenously dispersed cobalt sulfide nanoparticles that anchored on the N,S co-doped carbon framework. Because of the coupling effect of cobalt sulfide and doping heteroatoms, CoS@NSC-800 not only displays excellent electrocatalytic performances with low overpotential and high current density toward both oxygen reduction reaction and oxygen evolution reaction comparable to the commercial Pt/C catalyst and IrO 2 catalyst, but also might be a promising candidate for high-performance supercapacitors. The method for the preparation of the multifunctional hybrids is simple but effective for the formation of uniformly distributed metal sulfide nanoparticles anchored on carbon materials, therefore providing a new perspective for the design and synthesis of multifunctional electrocatalysts for electrochemical energy conversion and storage at a large scale.

Study of the interaction of the rupture zones of contiguous anchor plates in analogical medium

Directory of Open Access Journals (Sweden)

Abbad H.

2018-01-01

Full Text Available Knowing what occurs above anchor plates is certainly instructive. In this general vision of the interaction soil-anchor plates that our work was directed. An experimental study which required the design and implantation of a model containing plastic granules powder to similate a natural environment, is presented. The latter is subjected to the removal of anchor paltes. For each test, digital photographs are taken to materialize different deformed configurations during the pullout process. These photos processed in couples by the 7D software (image correlation giving the evolution of the displacement field and plane strain analogical environment. Particular attention is paid to the discussion of the interference of rupture zones of contiguous anchors by reducing the distance between plates.

Career Anchors and the Effects of Downsizing: Implications for Generations and Cultures at Work. A Preliminary Investigation.

Science.gov (United States)

Marshall, Verena; Bonner, Dede

2003-01-01

The relationships among career anchors, age, culture, gender, employment experience, and the impact of career planning on downsizing were examined with data from 423 management students (49% had been downsized). Lifestyle was the most valued anchor across age groups, stability/security the least; compared with Schein's earlier anchors research,…

CROSS DRIFT ALCOVE/NICHE UTILITIES ANALYSIS

International Nuclear Information System (INIS)

S. Goodin

1999-01-01

The purpose of this analysis is to provide the design basis and general arrangement requirements of the non-potable water, waste water, compressed air and ventilation (post excavation) utilities required in support of the Cross Drift alcoves and niches

Amplatzer Vascular Plug Anchoring Technique to Stabilize the Delivery System for Microcoil Embolization

International Nuclear Information System (INIS)

Onozawa, Shiro; Murata, Satoru; Mine, Takahiko; Sugihara, Fumie; Yasui, Daisuke; Kumita, Shin-ichiro

2016-01-01

PurposeTo evaluate the feasibility of a novel embolization technique, the Amplatzer vascular plug (AVP) anchoring technique, to stabilize the delivery system for microcoil embolization.Materials and methodsThree patients were enrolled in this study, including two cases of internal iliac artery aneurysms and one case of internal iliac arterial occlusion prior to endovascular aortic repair. An AVP was used in each case for embolization of one target artery, and the AVP was left in place. The AVP detachment wire was then used as an anchor to stabilize the delivery system for microcoil embolization to embolize the second target artery adjacent to the first target artery. The microcatheter for the microcoils was inserted parallel to the AVP detachment wire in the guiding sheath or catheter used for the AVP.ResultsThe AVP anchoring technique was achieved and the microcatheter was easily advanced to the second target artery in all three cases.ConclusionThe AVP anchoring technique was found to be feasible to advance the microcatheter into the neighboring artery of an AVP-embolized artery.

Proposed Methodology for Design of Carbon Fiber Reinforced Polymer Spike Anchors into Reinforced Concrete

Energy Technology Data Exchange (ETDEWEB)

MacFarlane, Eric Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-05-26

The included methodology, calculations, and drawings support design of Carbon Fiber Reinforced Polymer (CFRP) spike anchors for securing U-wrap CFRP onto reinforced concrete Tbeams. This content pertains to an installation in one of Los Alamos National Laboratory’s facilities. The anchors are part of a seismic rehabilitation to the subject facility. The information contained here is for information purposes only. The reader is encouraged to verify all equations, details, and methodology prior to usage in future projects. However, development of the content contained here complied with Los Alamos National Laboratory’s NQA-1 quality assurance program for nuclear structures. Furthermore, the formulations and details came from the referenced published literature. This literature represents the current state of the art for FRP anchor design. Construction personnel tested the subject anchor design to the required demand level demonstrated in the calculation. The testing demonstrated the ability of the anchors noted to carry loads in excess of 15 kips in direct tension. The anchors were not tested to failure in part because of the hazards associated with testing large-capacity tensile systems to failure. The calculation, methodology, and drawing originator was Eric MacFarlane of Los Alamos National Laboratory’s (LANL) Office of Seismic Hazards and Risk Mitigation (OSHRM). The checker for all components was Mike Salmon of the LANL OSHRM. The independent reviewers of all components were Insung Kim and Loring Wyllie of Degenkolb Engineers. Note that Insung Kim contributed to the initial formulations in the calculations that pertained directly to his Doctoral research.

Task difficulty has no effect on haptic anchoring during tandem walking in young and older adults.

Science.gov (United States)

Costa, Andréia Abud da Silva; Santos, Luciana Oliveira Dos; Mauerberg-deCastro, Eliane; Moraes, Renato

2018-02-14

This study assessed the contribution of the "anchor system's" haptic information to balance control during walking at two levels of difficulty. Seventeen young adults and seventeen older adults performed 20 randomized trials of tandem walking in a straight line, on level ground and on a slightly-raised balance beam, both with and without the use of the anchors. The anchor consists of two flexible cables, whose ends participants hold in each hand, to which weights (125 g) are attached at the opposing ends, and which rest on the ground. As the participants walk, they pull on the cables, dragging the anchors. Spatiotemporal gait variables (step speed and single- and double-support duration) were processed using retro-reflective markers on anatomical sites. An accelerometer positioned in the cervical region registered trunk acceleration. Walking on the balance beam increased single- and double-support duration and reduced step speed in older adults, which suggests that this condition was more difficult than walking on the level ground. The anchors reduced trunk acceleration in the frontal plane, but the level of difficulty of the walking task showed no effect. Thus, varying the difficulty of the task had no influence on the way in which participants used the anchor system while tandem walking. The older adults exhibited more difficulty in walking on the balance beam as compared to the younger adults; however, the effect of the anchor system was similar in both groups. Copyright © 2017 Elsevier B.V. All rights reserved.

Evaluation of postoperative results from videoarthroscopic treatment for recurrent shoulder dislocation using metal anchors

Directory of Open Access Journals (Sweden)

Éder Menegassi Martel

2016-02-01

Full Text Available ABSTRACT OBJECTIVE: To clinically and radiologically evaluate the results from videoarthroscopic treatment using metal anchors in patients with recurrent shoulder dislocation and its complications. METHODS: This was a retrospective study on 47 patients (47 shoulders operated by the shoulder group of the orthopedic hospital between February 2010 and February 2012. A questionnaire, interview and physical and radiographic examinations were used, with the classification of Samilson and Pietro. The mean postoperative follow-up was 33 months (range 12-47 months. The statistical analysis consisted of using Fisher's exact test through the IBM SPSS 22 statistical software. The significance level used was 5%. RESULTS: Recurrence was observed in nine cases. The patients were, on average, 26.5 years old at the first episode, and 19.1% were aged 20 years or under. Among these, 55.6% presented recurrence. In relation to age at the time of the surgical procedure, the average age was 27 years, and 12.8% were aged 20 years or under. Nineteen patients presented prominent anchors and, of these, 21% manifested arthrosis. CONCLUSION: There was a statistically identified correlation between the recurrence rate and age less than or equal to 20 years at the times of first dislocation and the surgical procedure. Further studies should be conducted in order to compare the use of absorbable anchors, which despite higher cost, may provide lower risk of developing glenohumeral arthrosis in some cases.

Final Technical Report Advanced Anchoring Technology DOE Award Number DE-EE0003632 Project Period 09/10 - 09/12

Energy Technology Data Exchange (ETDEWEB)

Meggitt, Dallas J

2012-11-09

It is generally conceded that the costs associated with current practices for the mooring, anchoring, or foundation systems of Marine HydroKinetic (MHK) and Deepwater Floating Wind systems are a disproportionate portion of the total cost of an installed system. Reducing the cost of the mooring and anchoring components for MHK systems can contribute substantially to reducing the levelized cost of electricity (LCOE). Micropile anchors can reduce the LCOE both directly, because the anchors, associated mooring hardware and installation costs are less than conventional anchor and mooring systems, but also because micropile anchors require less extensive geotechnical surveys for confident design and proper implementation of an anchor or foundation system. This report presents the results of the development of critical elements of grouted marine micropile anchor (MMA) technology for application to MHK energy conversion systems and other ocean engineering applications that require fixing equipment to the seafloor. Specifically, this project identified grout formulations and developed designs for grout dispensing systems suitable for use in a seawater environment as a critical development need for successful implementation of practical MMA systems. The project conducted a thorough review of available information on the use of cement-based grouts in seawater. Based on this review and data available from commercial sources, the project selected a range of grout formulations for testing as part of a micropile system. The project also reviewed instrumentation for measuring grout density, pressure and flow rate, and integrated an instrumentation system suitable for use with micropile installation. The grout formulations and instrumentation system were tested successfully and demonstrated the suitability of MMA technology for implementation into anchor systems for MHK and other marine renewable energy systems. In addition, this project developed conceptual designs for micropile

Anchors from Goa waters, central west coast of India: Remains of Goa's overseas trade contacts with Arabian countries and Portugal

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.; Gaur, A.S.; Sundaresh

iron anchors, five anchors are similar in shape and belong to the 16th-17th century, whereas the other two anchors are similar in shape and datable to the 18th century. None of the stone or iron anchors have been found with any datable context except...

Towards robot-assisted anchor deployment in beating-heart mitral valve surgery.

Science.gov (United States)

Cheng, Lingbo; Sharifi, Mojtaba; Tavakoli, Mahdi

2018-06-01

Beating-heart intracardiac surgery promises significant benefits for patients compared with cardiopulmonary bypass based procedures. However, the fast motions of the heart introduce serious challenges for surgeons. In this work, a new impedance-controlled master-slave telerobotic system is developed to help perform anchor deployment for mitral valve annuloplasty under the guidance of live ultrasound images of the heart. The proposed bilateral teleoperation system can both reflect the non-oscillatory portion of slave-heart tissue interaction force on the surgeon's hand as haptic feedback and implement rapid compensation for the beating heart's motion. The surgical task involves performing anchor deployment on a simulated moving heart tissue to evaluate the effectiveness of the proposed strategy for safely interacting with a moving organ. The results obtained show that the telerobotic system increases the success rate of anchor deployment by 100% and reduces the excess force application rate by 70% compared with manual attempts. Copyright © 2018 John Wiley & Sons, Ltd.

Career anchor profiles of a sample of business and professional women

Directory of Open Access Journals (Sweden)

Ronel Erwee

1990-06-01

Full Text Available The career anchors of a sample of 95 business and professional woman were studied by means of the Career Orientations Inventory (DeLong, 1982. The hierarchy of career anchors of the sample was as follows: Service, Variety, Security (job tenure, Managerial competence. Autonomy, Identity, Technical/functional competence, Entrepreneurship and Security (geographical location. A few significant differences in career anchors did occur between various occupational groups. The implicatons of these findings in terms of career management in organisations are discussed. Opsomming Die loopbaanankers van 'n steekproef van 95 sake- en beroepsvroue is bestudeer deur middel van die "Career Orientations Inventory" (DeLong, 1982. Die steekproef het die volgende hierargie van loopbaanankers getoon: Diens, Verskeidenheid, Sekuriteit (organisatories, Bestuursbevoegdheid, Outonomie, Identiteit, Tegnies/funksionele bevoegdheid, Entrepreneurskap en Sekuriteit (geografies. 'n Paar beduidende verskille in loopbaanankerprofiele het tussen die onderskeie beroepsgroepe voorgekom. Die implikasies van die bevindings ten opsigte van loopbaanbeplanning in ondernemings word bespreek.

Cost analysis of energy storage systems for electric utility applications

Energy Technology Data Exchange (ETDEWEB)

Akhil, A. [Sandia National Lab., Albuquerque, NM (United States); Swaminathan, S.; Sen, R.K. [R.K. Sen & Associates, Inc., Bethesda, MD (United States)

1997-02-01

Under the sponsorship of the Department of Energy, Office of Utility Technologies, the Energy Storage System Analysis and Development Department at Sandia National Laboratories (SNL) conducted a cost analysis of energy storage systems for electric utility applications. The scope of the study included the analysis of costs for existing and planned battery, SMES, and flywheel energy storage systems. The analysis also identified the potential for cost reduction of key components.

Comparison of two bone anchored hearing instruments: BP100 and Ponto Pro

DEFF Research Database (Denmark)

Olsen, Steen Østergaard; Glad, Henrik; Nielsen, Lars Holme

2011-01-01

This study aimed at investigating if there were differences in auditory performance, operation, or user preference between the Ponto Pro or the BP100, two bone anchored hearing instruments (BAHI) with modern sound processing technology.......This study aimed at investigating if there were differences in auditory performance, operation, or user preference between the Ponto Pro or the BP100, two bone anchored hearing instruments (BAHI) with modern sound processing technology....

Installation process of suction anchors in Gulf of Guinea clay : Centrifuge modelling

OpenAIRE

THOREL, Luc; GARNIER, Jacques; RAULT, Gérard; DENDANI, Hédi; COLLIAT, JL

2010-01-01

The preparation process of a deepwater Gulf of Guinea clay for modelling of 24 m long suction anchors at a scale of 1/100 in the LCPC centrifuge, the clay characteristics and the installation phase (self-weight and suction) are presented. Two types of caissons have been tested in each tub : one with stiffeners and the other without stiffener. The embedment ratio is close to the suction caisson's slenderness of 3. An analysis of the forces of suction and soil friction shows, as expected, hi...

Solid phase extraction of uranium(VI) onto benzoylthiourea-anchored activated carbon

International Nuclear Information System (INIS)

Zhao Yongsheng; Liu Chunxia; Feng Miao; Chen Zhen; Li Shuqiong; Tian Gan; Wang Li; Huang Jingbo; Li Shoujian

2010-01-01

A new solid phase extractant selective for uranium(VI) based on benzoylthiourea anchored to activated carbon was developed via hydroxylation, amidation and reaction with benzoyl isothiocyanate in sequence. Fourier transform infrared spectroscopy and total element analysis proved that benzoylthiourea had been successfully grafted to the surface of the activated carbon, with a loading capacity of 1.2 mmol benzoylthiourea per gram of activated carbon. The parameters that affect the uranium(VI) sorption, such as contact time, solution pH, initial uranium(VI) concentration, adsorbent dose and temperature, have been investigated. Results have been analyzed by Langmuir and Freundlich isotherm; the former was more suitable to describe the sorption process. The maximum sorption capacity (82 mg/g) for uranium(VI) was obtained at experimental conditions. The rate constant for the uranium sorption by the as-synthesized extractant was 0.441 min -1 from the first order rate equation. Thermodynamic parameters (ΔH 0 = -46.2 kJ/mol; ΔS 0 = -98.0 J/mol K; ΔG 0 = -17.5 kJ/mol) showed the adsorption of an exothermic process and spontaneous nature, respectively. Additional studies indicated that the benzoylthiourea-anchored activated carbon (BT-AC) selectively sorbed uranyl ions in the presence of competing ions, Na + , Co 2+ , Sr 2+ , Cs + and La 3+ .

Structural models of the membrane anchors of envelope glycoproteins E1 and E2 from pestiviruses

Science.gov (United States)

Wang, Jimin; Li, Yue; Modis, Yorgo

2014-01-01

The membrane anchors of viral envelope proteins play essential roles in cell entry. Recent crystal structures of the ectodomain of envelope protein E2 from a pestivirus suggest that E2 belongs to a novel structural class of membrane fusion machinery. Based on geometric constraints from the E2 structures, we generated atomic models of the E1 and E2 membrane anchors using computational approaches. The E1 anchor contains two amphipathic perimembrane helices and one transmembrane helix; the E2 anchor contains a short helical hairpin stabilized in the membrane by an arginine residue, similar to flaviviruses. A pair of histidine residues in the E2 ectodomain may participate in pH sensing. The proposed atomic models point to Cys987 in E2 as the site of disulfide bond linkage with E1 to form E1–E2 heterodimers. The membrane anchor models provide structural constraints for the disulfide bonding pattern and overall backbone conformation of the E1 ectodomain. PMID:24725935

ANTS-anchored Zn-Al-CO3-LDH particles as fluorescent probe for sensing of folic acid

International Nuclear Information System (INIS)

Liu, Pengfei; Liu, Dan; Liu, Yanhuan; Li, Lei

2016-01-01

A novel fluorescent nanosensor for detecting folic acid (FA) in aqueous media has been developed based on 8-aminonaphthalene-1,3,6-trisulfonate (ANTS) anchored to the surface of Zn-Al-CO 3 -layered double hydroxides (LDH) particles. The nanosensor showed high fluorescence intensity and good photostability due to a strong coordination interaction between surface Zn 2+ ions of Zn-Al-CO 3 -LDH and N atoms of ANTS, which were verified by result of X-ray photoelectron spectroscopy (XPS). ANTS-anchored on the surface of Zn-Al-CO 3 -LDH restricted the intra-molecular rotation leading to ANTS-anchored J-type aggregation emission enhancement. ANTS-anchored Zn-Al-CO 3 -LDH particles exhibited highly sensitive and selective response to FA over other common metal ions and saccharides present in biological fluids. The proposed mechanism was that oxygen atoms of -SO 3 groups in ANTS-anchored on the surface of Zn-Al-CO 3 -LDH were easily collided by FA molecules to form potential hydrogen bonds between ANTS-anchored and FA molecules, which could effectively quench the ANTS-anchored fluorescence. Under the simulated physiological conditions (pH of 7.4), the fluorescence quenching was fitted to Stern-Volmer equation with a linear response in the concentration range of 1 μM to 200 μM with a limit of detection of 0.1 μM. The results indicate that ANTS-anchored Zn-Al-CO 3 -LDH particles can afford a very sensitive system for the sensing FA in aqueous solution. - Highlights: • A novel fluorescent nanosensor has been developed. • The sensor exhibited highly sensitive and selective response to FA. • The fluorescence quenching was fitted to Stern–Volmer equation. • The linear response range was 1–200 μM with a limit of detection of 0.1 μM.

Discriminative ability of two different external anchors: improvement appears better than importance

DEFF Research Database (Denmark)

Lauridsen, Henrik Hein

2009-01-01

interpretable statistics such as proportions and numbers needed to treat can be reported based on the MIC. Estimating the MIC using the anchor-based method is, however, not without difficulties. For instance issues relating to calculation methods, measurement error, rater perspective, population specificity...... and baseline dependence have been raised, and little attention has been paid to how improvement and importance of a treatment outcome should be interpreted. The purpose of this study is to explore the adequateness of two different external anchors using the anchor-based MIC distribution method and probability...... of improvement/importance curves. Methods Two hundred and twenty-four patients with chronic low back pain and/or leg pain were recruited from an out-patient hospital back pain clinic and followed over an 8-week period. Participants received the Danish Oswestry Disability Index (ODI), the numeric rating scale...

Quantifying Heuristic Bias: Anchoring, Availability, and Representativeness.

Science.gov (United States)

Richie, Megan; Josephson, S Andrew

2018-01-01

Construct: Authors examined whether a new vignette-based instrument could isolate and quantify heuristic bias. Heuristics are cognitive shortcuts that may introduce bias and contribute to error. There is no standardized instrument available to quantify heuristic bias in clinical decision making, limiting future study of educational interventions designed to improve calibration of medical decisions. This study presents validity data to support a vignette-based instrument quantifying bias due to the anchoring, availability, and representativeness heuristics. Participants completed questionnaires requiring assignment of probabilities to potential outcomes of medical and nonmedical scenarios. The instrument randomly presented scenarios in one of two versions: Version A, encouraging heuristic bias, and Version B, worded neutrally. The primary outcome was the difference in probability judgments for Version A versus Version B scenario options. Of 167 participants recruited, 139 enrolled. Participants assigned significantly higher mean probability values to Version A scenario options (M = 9.56, SD = 3.75) than Version B (M = 8.98, SD = 3.76), t(1801) = 3.27, p = .001. This result remained significant analyzing medical scenarios alone (Version A, M = 9.41, SD = 3.92; Version B, M = 8.86, SD = 4.09), t(1204) = 2.36, p = .02. Analyzing medical scenarios by heuristic revealed a significant difference between Version A and B for availability (Version A, M = 6.52, SD = 3.32; Version B, M = 5.52, SD = 3.05), t(404) = 3.04, p = .003, and representativeness (Version A, M = 11.45, SD = 3.12; Version B, M = 10.67, SD = 3.71), t(396) = 2.28, p = .02, but not anchoring. Stratifying by training level, students maintained a significant difference between Version A and B medical scenarios (Version A, M = 9.83, SD = 3.75; Version B, M = 9.00, SD = 3.98), t(465) = 2.29, p = .02, but not residents or attendings. Stratifying by heuristic and training level, availability maintained

Rational use of anchor pile material of the thin retaining walls

Directory of Open Access Journals (Sweden)

Yushkov Boris Semenovich

2014-12-01

Full Text Available The article considers the urgency of application of the reinforced concrete anchor piles in the constructions of retaining structures associated with the possibility of establishing rigid joint of element interface and more durable pile constructions in the soil. The features of the inclined anchor piles work as a part of sheet-pile retaining walls are noted. There was performed a study of the stress-strain state of the inclined reinforced concrete anchor piles of the thin sheet-pile wall with the reinforced concrete face members of T-section, combined with piles by a longitudinal beam. The authors consider a constructive scheme of retaining structure and list the applied loads. The efforts in the anchor piles were determined. The bending-moment curves show the character of the force distribution along the pile. A form of the pile ensuring the rational distribution of material along the pile is presented. The distribution of efforts along the length and effect of filling on its operation in the soil were accepted as the criteria of construction solution for a pile. The substantiation of the proposed design of pile is presented in terms of its stress-strain state and the rational use of material. The authors made conclusions on the reasonability of adopted design solutions associated with an increase in the flexural strength of pile, increment of the ultimate pullout capacity, stability improvement, effective use of backfill and exception of the «out of operation» areas of the pile.

High Performance Flexible Pseudocapacitor based on Nano-architectured Spinel Nickel Cobaltite Anchored Multiwall Carbon Nanotubes

International Nuclear Information System (INIS)

Shakir, Imran

2014-01-01

Highlights: • Two-step fabrication method for nano-architectured spinel nickel cobaltite (NiCo 2 O 4 ) anchored MWCNTs composite. • High performance flexible energy-storage devices. • The NiCo 2 O 4 anchored MWCNTs Exhibits 2032 Fg −1 capacitance which is 1.62 times greater than pristine NiCo 2 O 4 at 1 Ag −1 . - Abstract: We demonstrate a facile two-step fabrication method for nano-architectured spinel nickel cobaltite (NiCo 2 O 4 ) anchored multiwall carbon nanotubes (MWCNTs) based electrodes for high performance flexible energy-storage devices. As electrode materials for flexible supercapacitors, the NiCo 2 O 4 anchored MWCNTs exhibits a high specific capacitance of 2032 Fg −1 , which is nearly 1.62 times greater than pristine NiCo 2 O 4 nanoflakes at 1 Ag −1 . The synthesized NiCo 2 O 4 anchored MWCNTs composite shows excellent rate performance (83.96% capacity retention at 30 Ag −1 ) and stability with coulombic efficiency over 96% after 5,000 cycles when being fully charged/discharged at 1 Ag −1 . Furthermore, NiCo 2 O 4 anchored MWCNTs achieve a maximum energy density of 48.32 Whkg −1 at a power density of 480 Wkg −1 which is 60% higher than pristine NiCo 2 O 4 electrode and significantly outperformed electrode materials based on NiCo 2 O 4 which are currently used in the state-of-the-art supercapacitors throughout the literature. This superior rate performance and high-capacity value offered by NiCo 2 O 4 anchored MWCNTs is mainly due to enhanced electronic and ionic conductivity, which provides a short diffusion path for ions and an easy access of electrolyte flow to nickel cobaltite redox centers besides the high conductivity of MWCNTs

A legged anchoring mechanism for capsule endoscopes using micropatterned adhesives.

Science.gov (United States)

Glass, Paul; Cheung, Eugene; Sitti, Metin

2008-12-01

This paper presents a new concept for an anchoring mechanism to enhance existing capsule endoscopes. The mechanism consists of three actuated legs with compliant feet lined with micropillar adhesives to be pressed into the intestine wall to anchor the device at a fixed location. These adhesive systems are inspired by gecko and beetle foot hairs. Single-leg and full capsule mathematical models of the forces generated by the legs are analyzed to understand capsule performance. Empirical friction models for the interaction of the adhesives with an intestinal substrate were experimentally determined in vitro using dry and oil-coated elastomer micropillar arrays with 140 microm pillar diameter, 105 microm spacing between pillars, and an aspect ratio of 1:1 on fresh porcine small intestine specimens. Capsule prototypes were also tested in a simulated intestine environment and compared with predicted peristaltic loads to assess the viability of the proposed design. The experimental results showed that a deployed 10 gr capsule robot can withstand axial peristaltic loads and anchor reliably when actuation forces are greater than 0.27 N using dry micropillars. Required actuation forces may be reduced significantly by using micropillars coated with a thin silicone oil layer.

Double-Row Suture Anchor Repair of Posterolateral Corner Avulsion Fractures.

Science.gov (United States)

Gilmer, Brian B

2017-08-01

Posterolateral corner avulsion fractures are a rare variant of ligamentous knee injury primarily described in the skeletally immature population. Injury is often related to a direct varus moment placed on the knee during sporting activities. Various treatment strategies have been discussed ranging from nonoperative management, to excision of the bony fragment, to primary repair with screws or suture. The described technique is a means for achieving fixation of the bony avulsion using principles familiar to double-row transosseous equivalent rotator cuff repair. Proximal anchors are placed in the epiphysis, and sutures are passed in horizontal mattress fashion. Once tied, the limbs of these same sutures are then passed to more distal anchors. Remaining eyelet sutures can be used to manage peripheral tissue. The final repair provides anatomic reduction and compression of the fragment to its bony bed with minimal extracortical hardware prominence and no violation of the physis. Risks include potential for physeal injury or chondral damage to the lateral femoral condyle through aberrant anchor placement. Postoperative care includes toe-touch weight-bearing restrictions and range of motion restrictions of 0°-90° in a hinged brace for 6 weeks followed by gradual return to activity.

A Single-hole stone anchor from Kottapatnam: Early historic port site of Andhra Pradesh, India

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.; Rao, K.P.; Kumari, S.; Imsong, O.; Vanlalhruaitluangi, V.

of Kottapatnam and this is the first stone anchor reported from Andhra coast. In this paper the single hole stone anchor has been detailed along with its probable period and the trade contacts of Kottapatnam as a port...

Study of intrinsic anchoring in nematic liquid crystals based on modified Gruhn-Hess pair potential

International Nuclear Information System (INIS)

Zhang Zhidong; Zhang Yanjun

2008-01-01

A nematic liquid crystal slab composed of N molecular layers is investigated using a simple cubic lattice model, based upon the molecular pair potential which is spatially anisotropic and dependent on elastic constants of liquid crystals. A perfect nematic order is assumed in the theoretical treatment, which means the orientation of the molecular long axis coincides with the director of liquid crystal and the total free energy equals to the total interaction energy. We present a modified Gruhn-Hess model, which is relative to the splay-bend elastic constant K 13 . Furthermore, we have studied the free nematic interfacial behavior (intrinsic anchoring) by this model in the assumption of the perfect nematic order. We find that the preferred orientation at the free interface and the intrinsic anchoring strength change with the value of modification, and that the director profile can be determined by the competition of the intrinsic anchoring with external forces present in the system. Also we simulate the intrinsic anchoring at different temperatures using Monte Carlo method and the simulation results show that the intrinsic anchoring favors planar alignment and the free interface is more disordered than the bulk

MAIL1 is essential for development of the primary root but not of anchor roots.

Science.gov (United States)

Ühlken, Christine; Hoth, Stefan; Weingartner, Magdalena

2014-01-01

MAIN-LIKE1 (MAIL1) is a ubiquitously expressed nuclear protein, which has a crucial function during root development. We have recently described loss of function mutants for MAIL1, in which the organization and function of the primary root meristem is lost soon after germination. Moreover cell differentiation is impaired resulting in primary root growth arrest soon after emergence. Here we show that mail1 mutants form several anchor roots from the hypocotyl to root junction. These anchor roots show similar defects in the organization of the stem cell niche as the primary root. In contrast, differentiation processes are not impaired and thus anchor roots seem to be able to compensate for the loss of primary root function. Our data show that MAIL1 is essential for specification of cell fate in the primary root but not in anchor roots.

Influence of weak anchoring upon the alignment of smectic A liquid crystals with surface pretilt

International Nuclear Information System (INIS)

De Vita, R; Stewart, I W

2008-01-01

Equilibrium configurations for smectic A liquid crystals in a 'bookshelf' geometry are determined from a nonlinear continuum model under strong and weak anchoring conditions at the boundary for the usual director n. Natural boundary conditions are derived for n and the smectic layer normal a when a preferred director orientation n p , which generally induces a director pretilt, is prescribed on the boundaries. Two key aspects are examined via the nonlinear equilibrium equations: the separation of n from a and the influence of weak anchoring. The orientations of n and a relative to n p may differ significantly and depend very much upon the magnitude of the anchoring strength. These results from a nonlinear theory are natural and novel developments of previous classical linearized models for which n ≡ a. Comparisons are also drawn between solutions for strong and weak anchoring conditions

Structural Behavior of a Long-Span Partially Earth-Anchored Cable-Stayed Bridge during Installation of a Key Segment by Thermal Prestressing

Directory of Open Access Journals (Sweden)

Sang-Hyo Kim

2016-08-01

Full Text Available This study investigated structural behavior of long-span partially earth-anchored cable-stayed bridges with a main span length of 810 m that use a new key segment closing method based on a thermal prestressing technique. A detailed construction sequence analysis matched with the free cantilever method (FCM was performed using a three-dimensional finite element (FE model of a partially earth-anchored cable-stayed bridge. The new method offers an effective way of connecting key segments by avoiding large movements resulting from the removal of the longitudinal restraint owing to the asymmetry of axial forces in the girders near the pylons. The new method develops new member forces through the process of heating the cantilever system before installing the key segment and cooling the system continuously after installing key segments. The resulting forces developed by the thermal process enhance the structural behavior of partially earth-anchored cable-stayed bridges owing to decreased axial forces in the girders.

Lower limit of strength wedge-type anchor bolts

International Nuclear Information System (INIS)

Arnedo Pena, A.; Frances Urmeneta, M.

1998-01-01

Simple expansion bolts, with a split expansion ring and a threaded bolt with an integral cone expander, called wedge type, are very used in securing and anchoring structures. The anchorage is obtained by a mechanism of torque-controlled expansion. Although less resistant than other types, its easy installation and low cost make them very competitive in light structures. In this paper, the minimum capacity values are analysed, when they are used to anchor safety-related equipment in NPP. The EPRI criteria developed in response to USI A-46 are applied and complemented by the new CEB Anchorage Design Guide. The results are compared with the information from european manufactures, adopting different safety factors for cracked and non-cracked concrete. With adequate control and inspection measures, including areas of noticeable cracking of concrete. minimum values for equipment can be obtained satisfying the strictest seismic validation requirements. (Author) 5 refs

Development of the Career Anchors Scale among Occupational Health Nurses in Japan.

Science.gov (United States)

Kubo, Yoshiko; Hatono, Yoko; Kubo, Tomohide; Shimamoto, Satoko; Nakatani, Junko; Burgel, Barbara J

2016-11-29

This study aimed to develop the Career Anchors Scale among Occupational Health Nurses (CASOHN) and evaluate its reliability and validity. Scale items were developed through a qualitative inductive analysis of interview data, and items were revised following an examination of content validity by experts and occupational health nurses (OHNs), resulting in a provisional scale of 41 items. A total of 745 OHNs (response rate 45.2%) affiliated with the Japan Society for Occupational Health participated in the self-administered questionnaire survey. Two items were deleted based on item-total correlations. Factor analysis was then conducted on the remaining 39 items to examine construct validity. An exploratory factor analysis with a main factor method and promax rotation resulted in the extraction of six factors. The variance contribution ratios of the six factors were 37.45, 7.01, 5.86, 4.95, 4.16, and 3.19%. The cumulative contribution ratio was 62.62%. The factors were named as follows: Demonstrating expertise and considering position in work (Factor 1); Management skills for effective work (Factor 2); Supporting health improvement in groups and organizations (Factor 3); Providing employee-focused support (Factor 4); Collaborating with occupational health team members and personnel (Factor 5); and Compatibility of work and private life (Factor 6). The confidence coefficient determined by the split-half method was 0.85. Cronbach's alpha coefficient for the overall scale was 0.95, whereas those of the six subscales were 0.88, 0.90, 0.91, 0.80, 0.85, and 0.79, respectively. CASOHN was found to be valid and reliable for measuring career anchors among OHNs in Japan.

Development of the Career Anchors Scale among Occupational Health Nurses in Japan

Science.gov (United States)

Kubo, Yoshiko; Hatono, Yoko; Kubo, Tomohide; Shimamoto, Satoko; Nakatani, Junko; Burgel, Barbara J.

2016-01-01

Objectives: This study aimed to develop the Career Anchors Scale among Occupational Health Nurses (CASOHN) and evaluate its reliability and validity. Methods: Scale items were developed through a qualitative inductive analysis of interview data, and items were revised following an examination of content validity by experts and occupational health nurses (OHNs), resulting in a provisional scale of 41 items. A total of 745 OHNs (response rate 45.2%) affiliated with the Japan Society for Occupational Health participated in the self-administered questionnaire survey. Results: Two items were deleted based on item-total correlations. Factor analysis was then conducted on the remaining 39 items to examine construct validity. An exploratory factor analysis with a main factor method and promax rotation resulted in the extraction of six factors. The variance contribution ratios of the six factors were 37.45, 7.01, 5.86, 4.95, 4.16, and 3.19%. The cumulative contribution ratio was 62.62%. The factors were named as follows: Demonstrating expertise and considering position in work (Factor 1); Management skills for effective work (Factor 2); Supporting health improvement in groups and organizations (Factor 3); Providing employee-focused support (Factor 4); Collaborating with occupational health team members and personnel (Factor 5); and Compatibility of work and private life (Factor 6). The confidence coefficient determined by the split-half method was 0.85. Cronbach's alpha coefficient for the overall scale was 0.95, whereas those of the six subscales were 0.88, 0.90, 0.91, 0.80, 0.85, and 0.79, respectively. Conclusions: CASOHN was found to be valid and reliable for measuring career anchors among OHNs in Japan. PMID:27725484

Method and apparatus for dismantling mechanical anchors

Energy Technology Data Exchange (ETDEWEB)

Dubovskiy, Yu P; Chendev, F S; Gritsayuk, B I; Gubin, N I; Osipov, S P

1982-01-01

This apparatus is designed to reduce the amount of labor required to dismantle mechanical anchors while at the same time lowering expenditures for lumber. Longwall beams and timber skips are used to support the cap and any fractured rock faces. The apparatus itself has grooves, vertical guides, and a drive system to position the longwall beams.

A Proteomics Investigation of Anchored PKA-RI Signaling

NARCIS (Netherlands)

Kovanich, D.

2013-01-01

Compartmentalization of kinases and phosphatases plays an important role in the specificity of second messenger mediated signaling events. Localization of the cAMP-dependent protein kinase is mediated by interaction of its regulatory subunit (PKA-R) with the versatile family of A-kinase anchoring

The bone-anchored hearing aid

DEFF Research Database (Denmark)

Foghsgaard, Søren

2014-01-01

The bone-anchored hearing aid (Baha) was introduced in 1977 by Tjellström and colleagues and has now been used clinically for over 30 years. Generally, the outcomes are good, and several studies have shown improved audiological- and quality of life outcomes. The principle of the Baha is, that sou...... vibrations are led directly to the inner ear via the mastoid bone, bypassing the middle ear. This is achieved via an osseointegrated implant and a skin-penetrating abutment. Studies report high success rates and a majority of complications as typically minor in nature....

Study on monitoring of deep foundation pit with SMW engineering method plus anchor cable retaining structure

Science.gov (United States)

Chen, Wenzhao; Cui, Wenping

2018-03-01

The SMW method has many advantages, such as little influence on the surrounding environment, good watertight performance, wide range of application, short construction period, low cost and so on. In this paper, we chose the SMW engineering method combined with anchor cable to support structure in the second phase deep foundation pit of Jinan LuJinDongCheng as the research object, monitored and analysed the horizontal displacement of the pile top, Peripheral surface subsidence and internal force of the anchor cable in the foundation pit. We also discussed the displacement, internal force of anchor cable and the settlement of surrounding environment in the excavation of foundation pit and in different stages of construction. Conclusion:(1)The maximum horizontal displacement of the retaining structure is closely related to the depth and time of excavation, the construction of anchor cable can well limit the deformation of pile body; (2)Groundwater seepage caused by foundation pit dewatering will change the effective stress of soil. The change of groundwater level has an important influence on the working behavior of smw anchor cable supporting structure.

Econophysical anchoring of unimodal power-law distributions

International Nuclear Information System (INIS)

Eliazar, Iddo I; Cohen, Morrel H

2013-01-01

The sciences are abundant with size distributions whose densities have a unimodal shape and power-law tails both at zero and at infinity. The quintessential examples of such unimodal and power-law (UPL) distributions are the sizes of income and wealth in human societies. While the tails of UPL distributions are precisely quantified by their corresponding power-law exponents, their bulks are only qualitatively characterized as unimodal. Consequently, different statistical models of UPL distributions exist, the most popular considering lognormal bulks. In this paper we present a general econophysical framework for UPL distributions termed ‘the anchoring method’. This method: (i) universally approximates UPL distributions via three ‘anchors’ set at zero, at infinity, and at an intermediate point between zero and infinity (e.g. the mode); (ii) is highly versatile and broadly applicable; (iii) encompasses the existing statistical models of UPL distributions as special cases; (iv) facilitates the introduction of new statistical models of UPL distributions and (v) yields a socioeconophysical analysis of UPL distributions. (paper)

Medicares Hospice Benefit - Analysis of Utilization and..

Data.gov (United States)

U.S. Department of Health & Human Services — Descriptive analyses reported in Medicares Hospice Benefit - Analysis of Utilization and Resource Use, published in Volume 4, Issue 3 of the Medicare and Medicaid...

Influence of weak anchoring upon the alignment of smectic A liquid crystals with surface pretilt

Energy Technology Data Exchange (ETDEWEB)

De Vita, R [Department of Engineering Science and Mechanics, Virginia Tech, 230 Norris Hall, Blacksburg, VA 24061 (United States); Stewart, I W [Department of Mathematics, University of Strathclyde, Livingstone Tower, 26 Richmond Street, Glasgow G1 1XH (United Kingdom)], E-mail: devita@vt.edu, E-mail: i.w.stewart@strath.ac.uk

2008-08-20

Equilibrium configurations for smectic A liquid crystals in a 'bookshelf' geometry are determined from a nonlinear continuum model under strong and weak anchoring conditions at the boundary for the usual director n. Natural boundary conditions are derived for n and the smectic layer normal a when a preferred director orientation n{sub p}, which generally induces a director pretilt, is prescribed on the boundaries. Two key aspects are examined via the nonlinear equilibrium equations: the separation of n from a and the influence of weak anchoring. The orientations of n and a relative to n{sub p} may differ significantly and depend very much upon the magnitude of the anchoring strength. These results from a nonlinear theory are natural and novel developments of previous classical linearized models for which n {identical_to} a. Comparisons are also drawn between solutions for strong and weak anchoring conditions.

Triple-Loaded Suture Anchors Versus a Knotless Rip Stop Construct in a Single-Row Rotator Cuff Repair Model.

Science.gov (United States)

Noyes, Matthew P; Lederman, Evan; Adams, Christopher R; Denard, Patrick J

2018-05-01

To compare the biomechanical properties of single-row repair with triple-loaded (TL) anchor repair versus a knotless rip stop (KRS) repair in a rotator cuff repair model. Rotator cuff tears were created in 8 cadaveric matched-pair specimens and repaired with a TL anchor or KRS construct. In the TL construct, anchors were placed in the greater tuberosity and then all suture limbs were passed through the rotator cuff as simple sutures and tied. In the KRS construct, a 2-mm suture tape was passed through the tendon in an inverted mattress fashion, and a free suture was passed medial to the suture tape to create a rip-stop. Then, the suture tape and free suture were secured with knotless anchors. Displacement was observed with video tracking after cyclic loading, and specimens were loaded to failure. The mean load to failure was 438 ± 59 N in TL anchor repairs compared with 457 ± 110 N in KRS repairs (P = .582). The mean displacement with cyclic loading was 3.8 ± 1.6 mm in TL anchor repairs versus 4.3 ± 1.8 mm in the KRS group (P = .297). Mode of failure was consistent in both groups, with 6 of 8 failures in the TL anchor group and 7 of 8 failures in KRS group occurring from anchor pullout. There is no statistical difference in load to failure and cyclic loading between TL anchor and KRS single-row repair techniques. KRS repair technique may be an alternative method of repairing full-thickness supraspinatus tendon tears with a single-row construct. Copyright © 2018 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

Binding constants of membrane-anchored receptors and ligands: A general theory corroborated by Monte Carlo simulations.

Science.gov (United States)

Xu, Guang-Kui; Hu, Jinglei; Lipowsky, Reinhard; Weikl, Thomas R

2015-12-28

Adhesion processes of biological membranes that enclose cells and cellular organelles are essential for immune responses, tissue formation, and signaling. These processes depend sensitively on the binding constant K2D of the membrane-anchored receptor and ligand proteins that mediate adhesion, which is difficult to measure in the "two-dimensional" (2D) membrane environment of the proteins. An important problem therefore is to relate K2D to the binding constant K3D of soluble variants of the receptors and ligands that lack the membrane anchors and are free to diffuse in three dimensions (3D). In this article, we present a general theory for the binding constants K2D and K3D of rather stiff proteins whose main degrees of freedom are translation and rotation, along membranes and around anchor points "in 2D," or unconstrained "in 3D." The theory generalizes previous results by describing how K2D depends both on the average separation and thermal nanoscale roughness of the apposing membranes, and on the length and anchoring flexibility of the receptors and ligands. Our theoretical results for the ratio K2D/K3D of the binding constants agree with detailed results from Monte Carlo simulations without any data fitting, which indicates that the theory captures the essential features of the "dimensionality reduction" due to membrane anchoring. In our Monte Carlo simulations, we consider a novel coarse-grained model of biomembrane adhesion in which the membranes are represented as discretized elastic surfaces, and the receptors and ligands as anchored molecules that diffuse continuously along the membranes and rotate at their anchor points.

Organization, 'Anchoring' of Knowledge, and Innovative Activity in Construction

DEFF Research Database (Denmark)

Drejer, Ina; Vinding, Anker Lund

2006-01-01

The construction industry is characterised by the widespread use of project organisation. It has been suggested that the relatively low level of innovative activity in the industry can be explained by the temporary nature of firm boundary-crossing projects. Survey data from the Danish construction...... industry is used to investigate the importance of learning and 'anchoring' of project-specific knowledge at the firm level for participation in innovative activities. The data cover both the overall Danish construction industry and a specific region, North Jutland, which has a relatively high...... specialisation of construction workers. Latent class and regression analyses reveal that firms that make extensive use of partnering, together with internal product and process evaluation and knowledge diffusion (labelled 'knowledge-anchoring mechanisms'), are more likely to participate in innovative activities...

Others' opinions count, but not all of them: anchoring to ingroup versus outgroup members' behavior in charitable giving

Directory of Open Access Journals (Sweden)

Dorina Hysenbelli

2013-11-01

Full Text Available Because of the large amount of information and the difficulty in selecting an appropriate recipient in the context of charitable giving, people tend to make extensive use of heuristics, which sometimes leads them to wrong decisions. In the present work, we focused on exploring how individuals are influenced by anchoring heuristics and how group membership interacts with this heuristic. In Experiment 1, two different groups of participants were informed about low versus high average donations of other people, and a third control group did not receive any information about the others' donations. The results showed that participants were willing to donate significantly more in the high-anchor condition compared to the low-anchor condition, as well as about the same amount of money in the low-anchor condition and no-anchor condition. Experiment 2 and 3 showed that high anchors are more effective when the information about others' donations reflects members of the ingroup rather than the outgroup. Other variables related to these results are further discussed.

Nanofabricated racks of aligned and anchored DNA substrates for single-molecule imaging.

Science.gov (United States)

Gorman, Jason; Fazio, Teresa; Wang, Feng; Wind, Shalom; Greene, Eric C

2010-01-19

Single-molecule studies of biological macromolecules can benefit from new experimental platforms that facilitate experimental design and data acquisition. Here we develop new strategies to construct curtains of DNA in which the molecules are aligned with respect to one another and maintained in an extended configuration by anchoring both ends of the DNA to the surface of a microfluidic sample chamber that is otherwise coated with an inert lipid bilayer. This "double-tethered" DNA substrate configuration is established through the use of nanofabricated rack patterns comprised of two distinct functional elements: linear barriers to lipid diffusion that align DNA molecules anchored by one end to the bilayer and antibody-coated pentagons that provide immobile anchor points for the opposite ends of the DNA. These devices enable the alignment and anchoring of thousands of individual DNA molecules, which can then be visualized using total internal reflection fluorescence microscopy under conditions that do not require continuous application of buffer flow to stretch the DNA. This unique strategy offers the potential for studying protein-DNA interactions on large DNA substrates without compromising measurements through application of hydrodynamic force. We provide a proof-of-principle demonstration that double-tethered DNA curtains made with nanofabricated rack patterns can be used in a one-dimensional diffusion assay that monitors the motion of quantum dot-tagged proteins along DNA.

[Treatment of calcaneal avulsion fractures with twinfix suture anchors fixation].

Science.gov (United States)

Zhao, Bin-xiu; Wang, Kun-zheng; Wang, Chun-sheng; Xie, Yue; Dai, Zhi-tang; Liu, Gang; Liu, Wei-dong

2011-06-01

For the calcaneal avulsion fracture, the current method is more commonly used screws or Kirschner wire to fix fracture fragment. This article intended to explore the feasibility and clinical efficacy for the treatment of avulsion fractures with TwinFix suture anchors. From July 2007 to November 2010, 21 patients were reviewed, including 15 males and 6 females, ranging in age from 49 to 65 years,with a mean of 58.7 years. Twelve patients had nodules in the right heel and 9 patients had nodules in the left heel. All the patients had closed fractures. The typical preoperative symptoms of the patients included pain in the upper heel and weak in heel lift. Body examination results: palpable sense of bone rubbing in the back of the heel, and swelling in the heel. Surgery treatment with TwinFix suture anchors performed as follows : to fix TwinFix suture anchors into the calcaneal body, then to drill the fracture block, to make the double strand suture through the fracture holes, to knot the suture eachother to fix the block, and to use stitch to fix the remaining suture in the Achilles tendon in order to improve the block fixation. The criteria of the AOFAS Foot and Ankle Surgery by the United States Association of ankle-rear foot functional recovery was used to evaluate the Achilles tendon. Total average score was (95.5 +/- 3.12) points, including pain items of(38.5 +/- 2.18) points,the average score of functional items of (49.5 +/- 3.09) points,and power lines of 10 points in all patients. Twenty-one patients got an excellent result, 16 good and 5 poor. The methods of treatment for the calcaneal avulsion fractures with TwinFix suture anchors is a simple operation, and have excellent clinical effect, which is worthy of promotion.

ANTS-anchored Zn-Al-CO{sub 3}-LDH particles as fluorescent probe for sensing of folic acid

Energy Technology Data Exchange (ETDEWEB)

Liu, Pengfei; Liu, Dan; Liu, Yanhuan [State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Beijing Key Laboratory of Environmentally Harmful Chemical Analysis, Beijing University of Chemical Technology, Beijing 100029 (China); Li, Lei, E-mail: lilei@mail.buct.edu.cn [State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Beijing Key Laboratory of Environmentally Harmful Chemical Analysis, Beijing University of Chemical Technology, Beijing 100029 (China)

2016-09-15

A novel fluorescent nanosensor for detecting folic acid (FA) in aqueous media has been developed based on 8-aminonaphthalene-1,3,6-trisulfonate (ANTS) anchored to the surface of Zn-Al-CO{sub 3}-layered double hydroxides (LDH) particles. The nanosensor showed high fluorescence intensity and good photostability due to a strong coordination interaction between surface Zn{sup 2+} ions of Zn-Al-CO{sub 3}-LDH and N atoms of ANTS, which were verified by result of X-ray photoelectron spectroscopy (XPS). ANTS-anchored on the surface of Zn-Al-CO{sub 3}-LDH restricted the intra-molecular rotation leading to ANTS-anchored J-type aggregation emission enhancement. ANTS-anchored Zn-Al-CO{sub 3}-LDH particles exhibited highly sensitive and selective response to FA over other common metal ions and saccharides present in biological fluids. The proposed mechanism was that oxygen atoms of -SO{sub 3} groups in ANTS-anchored on the surface of Zn-Al-CO{sub 3}-LDH were easily collided by FA molecules to form potential hydrogen bonds between ANTS-anchored and FA molecules, which could effectively quench the ANTS-anchored fluorescence. Under the simulated physiological conditions (pH of 7.4), the fluorescence quenching was fitted to Stern-Volmer equation with a linear response in the concentration range of 1 μM to 200 μM with a limit of detection of 0.1 μM. The results indicate that ANTS-anchored Zn-Al-CO{sub 3}-LDH particles can afford a very sensitive system for the sensing FA in aqueous solution. - Highlights: • A novel fluorescent nanosensor has been developed. • The sensor exhibited highly sensitive and selective response to FA. • The fluorescence quenching was fitted to Stern–Volmer equation. • The linear response range was 1–200 μM with a limit of detection of 0.1 μM.

Anatomic suture anchor versus the Broström technique for anterior talofibular ligament repair: a biomechanical comparison.

Science.gov (United States)

Waldrop, Norman E; Wijdicks, Coen A; Jansson, Kyle S; LaPrade, Robert F; Clanton, Thomas O

2012-11-01

Despite the popularity of the Broström procedure for secondary repair of chronic lateral ankle instability, there have been no biomechanical studies reporting on the strength of this secondary repair method, whether using suture fixation or suture anchors. The purpose of our study was to perform a biomechanical comparison of the ultimate load to failure and stiffness of the traditional Broström technique using only a suture repair compared with a suture anchor repair of the anterior talofibular ligament (ATFL) at time zero. We believed that fixation strength of the suture anchor repair would be closer to the strength of the native ligament and allow more aggressive rehabilitation. Controlled laboratory study. Twenty-four fresh-frozen cadaveric ankles were randomly divided into 4 groups of 6 specimens. One group was an intact control group, and the other groups consisted of the traditional Broström and 2 suture anchor modifications (suture anchors in talus or fibula) of the Broström procedure. The specimens were loaded to failure to determine the strength and stiffness of each construct. In load-to-failure testing, ultimate failure loads of the Broström (68.2 ± 27.8 N; P = .013), suture anchor fibula (79.2 ± 34.3 N; P = .037), and suture anchor talus (75.3 ± 45.6 N; P = .027) repairs were significantly lower than that of the intact (160.9 ± 72.2 N) ATFL group. Stiffness of the Broström (6.0 ± 2.5 N/mm; P = .02), suture anchor fibula (6.8 N/mm ± 2.7; P = .05), and suture anchor talus (6.6 N/mm ± 4.0; P = .04) repairs were significantly lower than that of the intact (12.4 N/mm ± 4.1 N/mm) ATFL group. The 3 repair groups were not significantly different from each other, but all 3 were substantially lower in strength and stiffness when compared to the intact ATFL. The use of suture anchors to repair the ATFL produces a repair that can withstand loads to failure similar to the suture-only Broström repair. However, all 3 repair groups were much weaker than

Dynamic behaviour of anchors in cracked and uncracked concrete: a progress report

International Nuclear Information System (INIS)

Rodriguez, M.; Klingner, R.E.

1997-01-01

In early 1993, the US Nuclear Regulatory Commission began a research program at The University of Texas at Austin, dealing with the dynamic behavior of anchors in cracked and uncracked concrete. In this paper, the progress of that research program is reviewed. The test program is summarized, and work performed to date is reviewed, with emphasis on the dynamic and static behavior of single tensile anchors in uncracked concrete. General conclusions from that work are discussed, and future plans are presented. (orig.)

Stable Pt clusters anchored to monovacancies on graphene sheets

Energy Technology Data Exchange (ETDEWEB)

Medasani, Bharat K.; Liu, Jun; Sushko, Maria L.

2017-10-09

anchor'>

The anchor-based minimal important change, based on receiver operating characteristic analysis or predictive modeling, may need to be adjusted for the proportion of improved patients.

Science.gov (United States)

Terluin, Berend; Eekhout, Iris; Terwee, Caroline B

2017-03-01

Patients have their individual minimal important changes (iMICs) as their personal benchmarks to determine whether a perceived health-related quality of life (HRQOL) change constitutes a (minimally) important change for them. We denote the mean iMIC in a group of patients as the "genuine MIC" (gMIC). The aims of this paper are (1) to examine the relationship between the gMIC and the anchor-based minimal important change (MIC), determined by receiver operating characteristic analysis or by predictive modeling; (2) to examine the impact of the proportion of improved patients on these MICs; and (3) to explore the possibility to adjust the MIC for the influence of the proportion of improved patients. Multiple simulations of patient samples involved in anchor-based MIC studies with different characteristics of HRQOL (change) scores and distributions of iMICs. In addition, a real data set is analyzed for illustration. The receiver operating characteristic-based and predictive modeling MICs equal the gMIC when the proportion of improved patients equals 0.5. The MIC is estimated higher than the gMIC when the proportion improved is greater than 0.5, and the MIC is estimated lower than the gMIC when the proportion improved is less than 0.5. Using an equation including the predictive modeling MIC, the log-odds of improvement, the standard deviation of the HRQOL change score, and the correlation between the HRQOL change score and the anchor results in an adjusted MIC reflecting the gMIC irrespective of the proportion of improved patients. Adjusting the predictive modeling MIC for the proportion of improved patients assures that the adjusted MIC reflects the gMIC. We assumed normal distributions and global perceived change scores that were independent on the follow-up score. Additionally, floor and ceiling effects were not taken into account. Copyright © 2017 Elsevier Inc. All rights reserved.

Solid phase extraction of uranium(VI) onto benzoylthiourea-anchored activated carbon

Energy Technology Data Exchange (ETDEWEB)

Zhao Yongsheng; Liu Chunxia; Feng Miao; Chen Zhen; Li Shuqiong; Tian Gan; Wang Li; Huang Jingbo [College of Chemistry, Sichuan University, 29 Wangjiang Lu, Chengdu, 610064, Sichuan (China); Li Shoujian, E-mail: sjli000616@scu.edu.cn [College of Chemistry, Sichuan University, 29 Wangjiang Lu, Chengdu, 610064, Sichuan (China)

2010-04-15

A new solid phase extractant selective for uranium(VI) based on benzoylthiourea anchored to activated carbon was developed via hydroxylation, amidation and reaction with benzoyl isothiocyanate in sequence. Fourier transform infrared spectroscopy and total element analysis proved that benzoylthiourea had been successfully grafted to the surface of the activated carbon, with a loading capacity of 1.2 mmol benzoylthiourea per gram of activated carbon. The parameters that affect the uranium(VI) sorption, such as contact time, solution pH, initial uranium(VI) concentration, adsorbent dose and temperature, have been investigated. Results have been analyzed by Langmuir and Freundlich isotherm; the former was more suitable to describe the sorption process. The maximum sorption capacity (82 mg/g) for uranium(VI) was obtained at experimental conditions. The rate constant for the uranium sorption by the as-synthesized extractant was 0.441 min{sup -1} from the first order rate equation. Thermodynamic parameters ({Delta}H{sup 0} = -46.2 kJ/mol; {Delta}S{sup 0} = -98.0 J/mol K; {Delta}G{sup 0} = -17.5 kJ/mol) showed the adsorption of an exothermic process and spontaneous nature, respectively. Additional studies indicated that the benzoylthiourea-anchored activated carbon (BT-AC) selectively sorbed uranyl ions in the presence of competing ions, Na{sup +}, Co{sup 2+}, Sr{sup 2+}, Cs{sup +} and La{sup 3+}.

Culturally-Anchored Values and University Education Experience Perception

Science.gov (United States)

Mitsis, Ann; Foley, Patrick

2009-01-01

Purpose: The purpose of this paper is to examine whether business students' gender, age and culturally-anchored values affect their perceptions of their university course experience. Design/methodology/approach: Culturally diverse business students (n 1/4 548) studying at an Australian university were surveyed using previously established scales.…

EFEKTIVITAS HYPNOTERAPI TEKNIK ANCHOR TERHADAP PERUBAHAN PERILAKU MEROKOK REMAJA Studi Pada Klien di Klinik Maulana Center of Hypnotherapy Palembang

Directory of Open Access Journals (Sweden)

Budiman Budiman

2017-02-01

Full Text Available Adolescent smoking behavior is one of the behaviors that are formed through the influence of  the  environment  and  the  curiosity  of a  teenager  on  the  enjoyment  of  cigarettes  by  a  teenager. Smoking is also not only occurs in adolescent boys by the results of the study found  that smoking behavior  also  applies  to  young  women  as  well  as  children  who  are  still  in  primary  school.  This study  examines  the  effectiveness  Anchor  Techniques  of  Hypnoterapy  toward  Adolescent  Smoking Behavior Change. Study for Client in The Clinic Maulana Center of Hypnotherapy Palembang. The hypothesis  of  this  study  is  there  Effect  of  Anchor  Techniques  of  Hypnoterapy  smoke  Adolescent Behavior Change. Research for Clients in The Clinic Maulana Center of Hypnotherapy Palembang. This  study  included  a  quantitative  study  in  which  research  methods  used  was  Quasi  Experiment design with pretest and posttest with non-control group design, a design study aimed at testing the causal  relationship  (Polit  &  Beck,  2006.  This  study  will  be  conducted  at  the  Clinic  Maulana Center  of  Hypnotherapy  Palembang  on  March-June  2015.  The  Clinic  is  located  at  street  Kebun Bunga  complex  BNI  Block  B  4  Sukarami  Palembang  and  sampling  techniques  using  purposive sampling with 15 respondens and using t-test data analysis and MANOVA. The results of this study stated  that  there  Effect  Anchor  Techniues  of  Hypnotherapy toward  Adolescent  Smoking  Behavior Change. The changes meant is leading to better behavior and that, of 15 people treated with anchor techniques of hypnotherapy 11 people stop smoking while two people can reduce the intensity and frequency of smoking to 78% while the two others are only able to be able to reduce the intensity of smoking 56, 3%. It is advisable to

Mining Tasks from the Web Anchor Text Graph: MSR Notebook Paper for the TREC 2015 Tasks Track

Science.gov (United States)

2015-11-20

Mining Tasks from the Web Anchor Text Graph: MSR Notebook Paper for the TREC 2015 Tasks Track Paul N. Bennett Microsoft Research Redmond, USA pauben...anchor text graph has proven useful in the general realm of query reformulation [2], we sought to quantify the value of extracting key phrases from...anchor text in the broader setting of the task understanding track. Given a query, our approach considers a simple method for identifying a relevant

Consistency Anchor Formalization and Correctness Proofs

OpenAIRE

Miguel, Correia; Bessani, Alysson

2014-01-01

This is report contains the formal proofs for the techniques for increasing the consistency of cloud storage as presented in "Bessani et al. SCFS: A Cloud-backed File System. Proc. of the 2014 USENIX Annual Technical Conference. June 2014." The consistency anchor technique allows one to increase the consistency provided by eventually consistent cloud storage services like Amazon S3. This technique has been used in the SCFS (Shared Cloud File System) cloud-backed file system for solving rea...

A genetically anchored physical framework for Theobroma cacao cv. Matina 1-6.

Science.gov (United States)

Saski, Christopher A; Feltus, Frank A; Staton, Margaret E; Blackmon, Barbara P; Ficklin, Stephen P; Kuhn, David N; Schnell, Raymond J; Shapiro, Howard; Motamayor, Juan Carlos

2011-08-16

The fermented dried seeds of Theobroma cacao (cacao tree) are the main ingredient in chocolate. World cocoa production was estimated to be 3 million tons in 2010 with an annual estimated average growth rate of 2.2%. The cacao bean production industry is currently under threat from a rise in fungal diseases including black pod, frosty pod, and witches' broom. In order to address these issues, genome-sequencing efforts have been initiated recently to facilitate identification of genetic markers and genes that could be utilized to accelerate the release of robust T. cacao cultivars. However, problems inherent with assembly and resolution of distal regions of complex eukaryotic genomes, such as gaps, chimeric joins, and unresolvable repeat-induced compressions, have been unavoidably encountered with the sequencing strategies selected. Here, we describe the construction of a BAC-based integrated genetic-physical map of the T. cacao cultivar Matina 1-6 which is designed to augment and enhance these sequencing efforts. Three BAC libraries, each comprised of 10× coverage, were constructed and fingerprinted. 230 genetic markers from a high-resolution genetic recombination map and 96 Arabidopsis-derived conserved ortholog set (COS) II markers were anchored using pooled overgo hybridization. A dense tile path consisting of 29,383 BACs was selected and end-sequenced. The physical map consists of 154 contigs and 4,268 singletons. Forty-nine contigs are genetically anchored and ordered to chromosomes for a total span of 307.2 Mbp. The unanchored contigs (105) span 67.4 Mbp and therefore the estimated genome size of T. cacao is 374.6 Mbp. A comparative analysis with A. thaliana, V. vinifera, and P. trichocarpa suggests that comparisons of the genome assemblies of these distantly related species could provide insights into genome structure, evolutionary history, conservation of functional sites, and improvements in physical map assembly. A comparison between the two T. cacao

A genetically anchored physical framework for Theobroma cacao cv. Matina 1-6

Directory of Open Access Journals (Sweden)

Kuhn David N

2011-08-01

Full Text Available Abstract Background The fermented dried seeds of Theobroma cacao (cacao tree are the main ingredient in chocolate. World cocoa production was estimated to be 3 million tons in 2010 with an annual estimated average growth rate of 2.2%. The cacao bean production industry is currently under threat from a rise in fungal diseases including black pod, frosty pod, and witches' broom. In order to address these issues, genome-sequencing efforts have been initiated recently to facilitate identification of genetic markers and genes that could be utilized to accelerate the release of robust T. cacao cultivars. However, problems inherent with assembly and resolution of distal regions of complex eukaryotic genomes, such as gaps, chimeric joins, and unresolvable repeat-induced compressions, have been unavoidably encountered with the sequencing strategies selected. Results Here, we describe the construction of a BAC-based integrated genetic-physical map of the T. cacao cultivar Matina 1-6 which is designed to augment and enhance these sequencing efforts. Three BAC libraries, each comprised of 10× coverage, were constructed and fingerprinted. 230 genetic markers from a high-resolution genetic recombination map and 96 Arabidopsis-derived conserved ortholog set (COS II markers were anchored using pooled overgo hybridization. A dense tile path consisting of 29,383 BACs was selected and end-sequenced. The physical map consists of 154 contigs and 4,268 singletons. Forty-nine contigs are genetically anchored and ordered to chromosomes for a total span of 307.2 Mbp. The unanchored contigs (105 span 67.4 Mbp and therefore the estimated genome size of T. cacao is 374.6 Mbp. A comparative analysis with A. thaliana, V. vinifera, and P. trichocarpa suggests that comparisons of the genome assemblies of these distantly related species could provide insights into genome structure, evolutionary history, conservation of functional sites, and improvements in physical map

Utility experience in reactor noise analysis in German LWRs

International Nuclear Information System (INIS)

Schuette, A.; Weingarten, J.; Wach, D.

1988-01-01

Reactor noise analysis has a long history in Fed. Rep. of Germany. Since the early 60ies it was directed to early fault, malfunction and anomaly detection in nuclear power plants. When successful diagnoses showed the high potential and benefits including economic and safety aspects, also the utilities began to have a vivid concern in application of the developed methods and systems. The know-how transfer from specialized teams to the onsite personnel as well as the development of more ''intelligent'' online systems are important present and future tasks for further improvement of their efficiency. The diagnostic group of GRS is active in both fields and has close cooperation with several utilities to achieve these objectives. Modern signal processing equipment and access to a comprehensive knowledge base stored in data banks are provided by the data analysis center of GRS. The available capabilities are described and examples of analysis results within the cooperation utilities/GRS are given. (author)

Setting sail for glucose homeostasis with the AKAP150-PP2B-anchor.

Science.gov (United States)

Teo, Adrian Kee Keong; Kulkarni, Rohit N

2012-10-17

Glucose-stimulated insulin secretion, controlled by multiple protein phosphorylation events, is critical for the regulation of glucose homeostasis. Protein kinase A (PKA) is known to play a role in β cell physiology, but the role of its anchoring protein is not fully understood. Hinke et al (2012) illustrate the significance of A-kinase anchoring protein 150 in tethering protein phosphatase 2B to mediate nutrient-stimulated insulin secretion and thus modulate glucose homeostasis.

The relation between career anchors, occupational types and job satisfaction of midcareer employees

OpenAIRE

J. A. Ellison; A. M. G. Schreuder

2000-01-01

The objective of this research was to determine the value of the career anchor model in career decision-making. Career models that can provide the individual with greater self-insight can serve as an important guide when making career choices in todays turbulent working environment. Two hundred and ninety-five midcareer employees (managerial and non-managerial) completed questionnaires to determine their career anchor, occupation type and levels of general, intrinsic and extrinsic job satisfa...

Anchoring samarium oxide nanoparticles on reduced graphene oxide for high-performance supercapacitor

Energy Technology Data Exchange (ETDEWEB)

Dezfuli, Amin Shiralizadeh [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of); Ganjali, Mohammad Reza, E-mail: ganjali@khayam.ut.ac.ir [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of); Biosensor Research Center, Endocrinology & Metabolism Molecular-Cellular Sciences Institute, Tehran University of Medical Sciences, Tehran (Iran, Islamic Republic of); Naderi, Hamid Reza [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of)

2017-04-30

Highlights: • Samarium oxide nanoparticles have been anchored on the surface of reduced graphene oxide for the first time. • Sm{sub 2}O{sub 3}/RGO nanocomposite show high capacitance, good rate and cycling performance. • Sm{sub 2}O{sub 3}/RGO nanocomposite can serve as efficient electrode material for energy storage. • The best composite electrode exhibits specific capacitance of 321 F g{sup −1} in 2 mV s{sup −1}. - Abstract: We have synthesized Sm{sub 2}O{sub 3} nanoparticles (SmNs) and anchored them onto the surface of reduced graphene oxide (RGO) through a self-assembly thereof by utilizing a facile sonochemical procedure. The nanomaterials were characterized by means of powder X-ray diffraction (XRD), Field-emission scanning electron microscopy (FE-SEM), fourier transform infrared spectroscopy (FT-IR) spectra, and X-ray photoelectron spectroscopy (XPS). As the next step, the supercapacitive behavior of the resulting nanocomposites were investigated when used as electrode material, through with cyclic voltammetric (CV), galvanostatic charge-discharge and electrochemical impedance spectroscopy (EIS) techniques. The SmNs decorated RGO (SmN-RGO) nanocomposites were found to possess a specific capacitance (SC) of 321 F g{sup −1} when used in a 0.5 M Na{sub 2}SO{sub 4} solution as an electrolyte, in a scan rate of 2 mV s{sup −1}. The SC of the SmN-RGO based electrodes were also found to be 268 F g{sup −1} at a current density of 2 A g{sup −1} through galvanostatic charge-discharge tests. The outstanding properties of the SmN-RGOs were attributed to synergy of the high charge mobility of SmNs and the flexibility of the sheets of RGOs. Additionally, the nano-composite revealed a unique cycling durability (maintaining 99% of its SC even after 4000 cycles).

Modeling and experimental validation of sawing based lander anchoring and sampling methods for asteroid exploration

Science.gov (United States)

Zhang, Jun; Dong, Chengcheng; Zhang, Hui; Li, Song; Song, Aiguo

2018-05-01

This paper presents a novel lander anchoring system based on sawing method for asteroid exploration. The system is composed of three robotic arms, three cutting discs, and a control system. The discs mounted at the end of the arms are able to penetrate into the rock surface of asteroids. After the discs cut into the rock surface, the self-locking function of the arms provides forces to fix the lander on the surface. Modeling, trajectory planning, simulations, mechanism design, and prototype fabrication of the anchoring system are discussed, respectively. The performances of the system are tested on different kinds of rocks, at different sawing angles, locations, and speeds. Results show that the system can cut 15 mm deep into granite rock in 180 s at sawing angle of 60°, with the average power of 58.41 W, and the "weight on bit" (WOB) of 8.637 N. The 7.8 kg anchoring system is capable of providing omni-directional anchoring forces, at least 225 N normal and 157 N tangent to the surface of the rock. The system has the advantages of low-weight, low energy consumption and balance forces, high anchoring efficiency and reliability, and could enable the lander to move and sample or assist astronauts and robots in walking and sampling on asteroids.

Induction of bone ingrowth with a micropore bioabsorbable suture anchor in rotator cuff tear: an experimental study in a rabbit model.

Science.gov (United States)

Kang, Yun Gyeong; Kim, Jung-Han; Shin, Jung-Woog; Baik, Jong-Min; Choo, Hye-Jung

2013-11-01

The bioabsorbable suture anchor is probably one of the most commonly used tools in arthroscopic shoulder operations. However, there is controversy about whether the bioabsorbable anchor is replaced by bone. The object of this study is to evaluate bone ingrowth into the micropore bioabsorbable suture anchor and the differences in the biomechanical properties of a micropore anchor and a nonpore anchor. A total of 16 microsized holes (diameter, 250 ± 50 μm; depth, 0.2 mm) were made on the bioabsorbable anchors with a microdrill. Twelve adult New Zealand White rabbits were randomly divided into two groups: group A (n = 6), the nonpore bioabsorbable suture anchor group, and group pA (n = 6), the micropore bioabsorbable suture anchor group. Microcomputed tomography was used at 4 and 8 weeks postoperatively to evaluate ingrowth by bone volume fraction (BVF), which was measured by calculating the ratio of the total volume of bone ingrowth to that of the region of interest. For pullout strength testing, 3 additional rabbits (6 limbs) were used for mechanical testing. The mean BVF was higher in group pA (0.288 ± 0.054) than in group A (0.097 ± 0.006). The micropore anchor had a higher pullout strength (0.520 ± 0.294 N) than the nonpore anchor (0.275 ± 0.064 N). Micropore bioabsorbable suture anchors induced bone ingrowth and showed higher pullout strength, despite processing. Copyright © 2013 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Mosby, Inc. All rights reserved.

The double-anchoring theory of lightness perception: a comment on Bressan (2006).

Science.gov (United States)

Howe, Piers D L; Sagreiya, Hersh; Curtis, Dwight L; Zheng, Chengjie; Livingstone, Margaret S

2007-10-01

Recently, a double-anchoring theory (DAT) of lightness perception was proposed (P. Bressan, 2006), which offers explanations for all the data explained by the original anchoring theory (A. Gilchrist et al., 1999), as well as a number of additional lightness phenomena. Consequently, DAT can account for an unprecedented range of empirical results, potentially explaining everything from the basic simultaneous contrast display to subtle variations of the Gelb effect. In this comment, the authors raised 4 concerns that demonstrate serious theoretical and empirical difficulties for DAT. PsycINFO Database Record (c) 2007 APA, all rights reserved.

Exploring body-anchored and experience-based learning in a community of practice

DEFF Research Database (Denmark)

Stelter, Reinhard

2008-01-01

which, in a second step, is presented as part of the social realm and as one of the prerequisites of learning in a community of practice. This integration is established and becomes visible through the following two concepts: 1. Reification as the outflow of co-ordinated action, and 2. narratives......The article aims to integrate body-anchored and experience-based learning in the theoretical concept of learning in a community of practice. Present moment, epoché, intentional orientation and meaning making are introduced as the four basic premises for body-anchored and experience-based learning...

Ten Anchor Points for Teaching Principles of Marketing

Science.gov (United States)

Tomkovick, Chuck

2004-01-01

Effective marketing instructors commonly share a love for their students, an affinity for the subject matter, and a devotion to continuous quality improvement. The purpose of this article is to highlight 10 anchor points for teaching Principles of Marketing, which are designed to better engage students in the learning process. These anchor…

Developing engineering analysis capabilities at a nuclear utility

International Nuclear Information System (INIS)

Miller, J.S.

1992-01-01

When a nuclear plant is originally designed and constructed, a large staff of analytical and design personnel is used by the architectural and engineering (A/E) firm(s) and the nuclear steam supply system (NSSS) engineering firm(s) to provide the technical specifications needed for the plant to function and satisfy US Nuclear Regulatory Commission (NRC) requirements. During this design process, thousands of calculations are performed, some using large sophisticated computer programs. Once the plant is operational, the utility assumes the large responsibility for plant design. Utility personnel must understand the fundamentals of operating the plant, the technical information in the updated safety analysis report, all calculations used to design the plant, and the input for all design specification documents. Without this knowledge, utility personnel cannot successfully perform modifications or new analyses required by the NRC, such as probabilistic risk assessment (PRA) and motor-operated valve programs, and maintain the safe and reliable operation of the plant. Therefore, it is very important to have on-site personnel who understand how the calculations are performed and used in the design basis. This paper discusses the organization of the engineering analysis group, which provides technical support for River Bend Station (RBS) of Gulf States Utilities

Analysis of Flexible Anchored Hollow WPC Quay Walls of the New Berth in Tur, Egypt

Science.gov (United States)

Elsayed, Ayman

2017-10-01

A seawall, also known as a bulkhead or retaining wall, is a structure built to reduce the effects of strong waves and to defend costal land from erosion. Traditionally, seawalls are made of steel, timber or concrete construction. Composite materials, however, have been recently introduced for their ease of installation/maintenance in dry processing, low cost, and environmentally friendly materials. A wood plastic composite (WPC) seawall system has been developed and patented for its unique hollow structure that can give greater stiffness and stability under various external stresses. This paper describes the development of design method used in the analysis of the WPC walls. The main challenge during the physical excavation works is to limit the deformations involved in order to minimize damage on adjacent structures. The deformations depend largely on the excavation and strutting procedures, but also on the properties of the structural elements like the soil, the sheet pile and strutting members. The detailed design procedure involves numerical analyses, national regulations and common practice considerations. The contribution of finite element method in this field was used herein to determine the lateral movements, the bending moments of the wall, the passive earth pressure of the soil and the tensile force exerted by the anchor rods. The overall objectives of this research can be divided into two categories, First calibration of the finite element model for the new Tur quay walls (the case study) and reviewing the results of the steel cross section that chosen and the suggested one. Second, analysis and comparing the results of WPC cross-sections with the designed Steel sheet pile wall (SPW).

Use of an all-suture anchor for re-creation of the anterior talofibular ligament: a case report.

Science.gov (United States)

Piraino, Jason A; Busch, Elliot L; Sansosti, Laura E; Pettineo, Steven J; Creech, Corine

2015-01-01

The lateral ankle ligament complex is typically injured during athletic activity caused by an inversion force on a plantar flexed foot. Numerous open surgical procedures to reconstruct the lateral ankle complex have been described. In contrast, we present a case report in which an all-suture anchor was used arthroscopically to re-create the anterior talofibular ligament in conjunction with ankle arthroscopy. A retrospective analysis of a 55-year-old male with a work-related inversion ankle sprain was performed with 14 months of follow-up. Objective and subjective assessments were obtained using range of motion measures, a strength assessment, and the Foot Function Index. An all-suture anchor was deployed through the anterolateral portal and secured in both the fibula and talus, re-creating the anterior talofibular ligament at its origin and insertion. Active range of motion physical therapy began at 2 weeks postoperatively. The patient started a neuromuscular re-education program at 5 weeks with minimal pain or discomfort. A return to full duty was achieved at 3 months postoperatively. To our knowledge, the use of an all-suture anchor has not been previously reported for lateral ankle complex re-creation. It is hoped that this approach to anterior talofibular ligament repair will decrease the incidence of complications and improve outcomes. Copyright © 2015 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

Degradation theories of concrete and development of a new deviatoric model in incremental tangent formulation: limit analysis applied to case of anchor bolts embedded in concrete

International Nuclear Information System (INIS)

Ung Quoc, H.

2003-12-01

This research is achieved in the general framework of the study of the concrete behaviour. It has for objective the development of a new behaviour model satisfying to the particular requirements for an industrial exploitation. After the analysis of different existent models, a first development has concerned models based on the smeared crack theory. A new formulation of the theory permitted to overcome the stress locking problem. However, the analysis showed the persistence of some limits inert to this approach in spite of this improvement. Then, an analysis of the physical mechanisms of the concrete degradation has been achieved and permitted to develop the new damage model MODEV. The general formulation of this model is based on the theory of the thermodynamics and applied to the case of the heterogeneous and brittle materials. The MODEV model considers two damage mechanisms: extension and sliding. The model considers also that the relative tangent displacement between microcracks lips is responsible of the strain irreversibility. Thus, the rate of inelastic strain becomes function of the damage and the heterogeneity index of the material. The unilateral effect is taken in account as an elastic hardening or softening process according to re-closing or reopening of cracks. The model is written within the framework of non standard generalised materials in incremental tangent formulation and implemented in the general finite element code SYMPHONIE. The validation of the model has been achieved on the basis of several tests issued from the literature. The second part of this research has concerned the development of the CHEVILAB software. This simulation tool based on the limit analysis approach permit the evaluation of the ultimate load capacity of anchors bolts. The kinematics approach of the limit analysis has been adapted to the problem of anchors while considering several specific failure mechanisms. This approach has been validated then by comparison with the

Decay accelerating factor (DAF) is anchored to membranes by a C-terminal glycolipid

International Nuclear Information System (INIS)

Medof, M.E.; Haas, R.; Walter, E.I.; Rosenberry, T.L.

1986-01-01

Purified 70 kDa membrane (m) DAF incorporates into cells when added in vitro. A 2 kDa smaller DAF form which functions extrinsically like C4bp but is unable to incorporate can be isolated from urine (u). Because of common deficits of mDAF and acetylcholinesterase (AChE) in erythrocytes (E) of patients with paroxysmal nocturnal hemoglobinuria (PNH), mDAF was analyzed for a O-terminal glycolipid membrane anchor similar to that in E AChE. Incubation of E with phosphatidylinositol-specific phospholipase C, an enzyme which cleaves a similar glycolipid anchor in trypanosome variant surface glycoproteins (mfVSGs), released 20% of the DAF antigen. The released DAF species resembled uDAF in size, extrinsic model of C4b2a decay, and lack of hydrophobicity. Reductive radiomethylation of mDAF with [ 14 C]HCHO and NaCNBH 3 revealed ethanolamine and glucosamine in proportions similar to those in the E AChE glycolipid anchor. Papain cleavage of radiomethylated mDAF released the labeled ethanolamine and glucosamine in small O-terminal fragments from the residual DAF that retained N-terminal Asp. Following labeling of the anchors of mDAF and E AChE with the lipophilic photoreagent 3-trifluoromethyl-3-(m-[ 125 I]iodophenyl)diazirine, cleavage at the glucosamine residue by deamination quantitatively released the label from both proteins. Biosynthetic labeling of Hela cells with [ 3 H]ethanolamine resulted in rapid 3 H incorporation into both 48 kDa proDAF and 70 kDa mDAF. These data indicate that mDAF is anchored by a glycolipid similar to that in E AChE, mfVSGs and Thy-1 antigen and raise the possibility that a defect in the assembly or attachment of this structure could account for the deficits of mDAF and E AChE in PNH

Protein-Anchoring Therapy of Biglycan for Mdx Mouse Model of Duchenne Muscular Dystrophy.

Science.gov (United States)

Ito, Mikako; Ehara, Yuka; Li, Jin; Inada, Kosuke; Ohno, Kinji

2017-05-01

Duchenne muscular dystrophy (DMD) is a devastating muscle disease caused by loss-of-function mutations in DMD encoding dystrophin. No rational therapy is currently available. Utrophin is a paralog of dystrophin and is highly expressed at the neuromuscular junction. In mdx mice, utrophin is naturally upregulated throughout the muscle fibers, which mitigates muscular dystrophy. Protein-anchoring therapy was previously reported, in which a recombinant extracellular matrix (ECM) protein is delivered to and anchored to a specific target using its proprietary binding domains. Being prompted by a report that intramuscular and intraperitoneal injection of an ECM protein, biglycan, upregulates expression of utrophin and ameliorates muscle pathology in mdx mice, protein-anchoring therapy was applied to mdx mice. Recombinant adeno-associated virus serotype 8 (rAAV8) carrying hBGN encoding human biglycan was intravenously injected into 5-week-old mdx mice. The rAAV8-hBGN treatment improved motor deficits and decreased plasma creatine kinase activities. In muscle sections of treated mice, the number of central myonuclei and the distribution of myofiber sizes were improved. The treated mice increased gene expressions of utrophin and β1-syntrophin, as well as protein expressions of biglycan, utrophin, γ-sarcoglycan, dystrobrevin, and α1-syntrophin. The expression of hBGN in the skeletal muscle of the treated mice was 1.34-fold higher than that of the native mouse Bgn (mBgn). The low transduction efficiency and improved motor functions suggest that biglycan expressed in a small number of muscle fibers was likely to have been secreted and anchored to the cell surface throughout the whole muscular fibers. It is proposed that the protein-anchoring strategy can be applied not only to deficiency of an ECM protein as previously reported, but also to augmentation of a naturally induced ECM protein.

Root hairs aid soil penetration by anchoring the root surface to pore walls.

Science.gov (United States)

Bengough, A Glyn; Loades, Kenneth; McKenzie, Blair M

2016-02-01

The physical role of root hairs in anchoring the root tip during soil penetration was examined. Experiments using a hairless maize mutant (Zea mays: rth3-3) and its wild-type counterpart measured the anchorage force between the primary root of maize and the soil to determine whether root hairs enabled seedling roots in artificial biopores to penetrate sandy loam soil (dry bulk density 1.0-1.5g cm(-3)). Time-lapse imaging was used to analyse root and seedling displacements in soil adjacent to a transparent Perspex interface. Peak anchorage forces were up to five times greater (2.5N cf. 0.5N) for wild-type roots than for hairless mutants in 1.2g cm(-3) soil. Root hair anchorage enabled better soil penetration for 1.0 or 1.2g cm(-3) soil, but there was no significant advantage of root hairs in the densest soil (1.5g cm(-3)). The anchorage force was insufficient to allow root penetration of the denser soil, probably because of less root hair penetration into pore walls and, consequently, poorer adhesion between the root hairs and the pore walls. Hairless seedlings took 33h to anchor themselves compared with 16h for wild-type roots in 1.2g cm(-3) soil. Caryopses were often pushed several millimetres out of the soil before the roots became anchored and hairless roots often never became anchored securely.The physical role of root hairs in anchoring the root tip may be important in loose seed beds above more compact soil layers and may also assist root tips to emerge from biopores and penetrate the bulk soil. © The Author 2016. Published by Oxford University Press on behalf of the Society for Experimental Biology.

A general pipeline for the development of anchor markers for comparative genomics in plants

Directory of Open Access Journals (Sweden)

Stougaard Jens

2006-08-01

Full Text Available Abstract Background Complete or near-complete genomic sequence information is presently only available for a few plant species representing a large phylogenetic diversity among plants. In order to effectively transfer this information to species lacking sequence information, comparative genomic tools need to be developed. Molecular markers permitting cross-species mapping along co-linear genomic regions are central to comparative genomics. These "anchor" markers, defining unique loci in genetic linkage maps of multiple species, are gene-based and possess a number of features that make them relatively sparse. To identify potential anchor marker sequences more efficiently, we have established an automated bioinformatic pipeline that combines multi-species Expressed Sequence Tags (EST and genome sequence data. Results Taking advantage of sequence data from related species, the pipeline identifies evolutionarily conserved sequences that are likely to define unique orthologous loci in most species of the same phylogenetic clade. The key features are the identification of evolutionarily conserved sequences followed by automated design of intron-flanking Polymerase Chain Reaction (PCR primer pairs. Polymorphisms can subsequently be identified by size- or sequence variation of PCR products, amplified from mapping parents or populations. We illustrate our procedure in legumes and grasses and exemplify its application in legumes, where model plant studies and the genome- and EST-sequence data available have a potential impact on the breeding of crop species and on our understanding of the evolution of this large and diverse family. Conclusion We provide a database of 459 candidate anchor loci which have the potential to serve as map anchors in more than 18,000 legume species, a number of which are of agricultural importance. For grasses, the database contains 1335 candidate anchor loci. Based on this database, we have evaluated 76 candidate anchor loci

A new technique of "midline anchoring" in spinal cord stimulation dramatically reduces lead migration.

Science.gov (United States)

Mironer, Y Eugene; Brown, Christopher; Satterthwaite, John R; Cohen, Mary; Tonder, Lisa M; Grumman, Steve

2004-01-01

Spinal cord stimulation (SCS) is a popular method of treatment of chronic pain. Unfortunately, migration of the lead continues to be a serious complication of this therapy. In an attempt to reduce lateral migration of the SCS lead, we performed a retrospective assessment of a new technique of percutaneous lead placement. This new method of "midline anchoring" of the lead using the plica mediana dorsalis was tested against conventional technique in a retrospective study involving 122 trials and 91 implants of SCS over a period of five years. The use of "midline anchoring" resulted in a decrease in lead migration from 23% to 6% after trial insertion and from 24% to 7% after implantation. We conclude that "midline anchoring" of the SCS lead is an effective method of preventing lead migration.

Tritium labelling of a cholesterol amphiphile designed for cell membrane anchoring of proteins.

Science.gov (United States)

Schäfer, Balázs; Orbán, Erika; Kele, Zoltán; Tömböly, Csaba

2015-01-01

Cell membrane association of proteins can be achieved by the addition of lipid moieties to the polypeptide chain, and such lipid-modified proteins have important biological functions. A class of cell surface proteins contains a complex glycosylphosphatidylinositol (GPI) glycolipid at the C-terminus, and they are accumulated in cholesterol-rich membrane microdomains, that is, lipid rafts. Semisynthetic lipoproteins prepared from recombinant proteins and designed lipids are valuable probes and model systems of the membrane-associated proteins. Because GPI-anchored proteins can be reinserted into the cell membrane with the retention of the biological function, they are appropriate candidates for preparing models via reduction of the structural complexity. A synthetic headgroup was added to the 3β-hydroxyl group of cholesterol, an essential lipid component of rafts, and the resulting cholesterol derivative was used as a simplified GPI mimetic. In order to quantitate the membrane integrated GPI mimetic after the exogenous addition to live cells, a tritium labelled cholesterol anchor was prepared. The radioactive label was introduced into the headgroup, and the radiolabelled GPI mimetic anchor was obtained with a specific activity of 1.37 TBq/mmol. The headgroup labelled cholesterol derivative was applied to demonstrate the sensitive detection of the cell membrane association of the anchor under in vivo conditions. Copyright © 2015 John Wiley & Sons, Ltd.

Anchored PKA as a gatekeeper for gap junctions.

Science.gov (United States)

Pidoux, Guillaume; Taskén, Kjetil

2015-01-01

Anchored protein kinase A (PKA) bound to A Kinase Anchoring Protein (AKAP) mediates effects of localized increases in cAMP in defined subcellular microdomains and retains the specificity in cAMP-PKA signaling to distinct extracellular stimuli. Gap junctions are pores between adjacent cells constituted by connexin proteins that provide means of communication and transfer of small molecules. While the PKA signaling is known to promote human trophoblast cell fusion, the gap junction communication through connexin 43 (Cx43) is a prerequisite for this process. We recently demonstrated that trophoblast fusion is regulated by ezrin, a known AKAP, which binds to Cx43 and delivers PKA in the vicinity gap junctions. We found that disruption of the ezrin-Cx43 interaction abolished PKA-dependent phosphorylation of Cx43 as well as gap junction communication and subsequently cell fusion. We propose that the PKA-ezrin-Cx43 macromolecular complex regulating gap junction communication constitutes a general mechanism to control opening of Cx43 gap junctions by phosphorylation in response to cAMP signaling in various cell types.

Analytical and experimental evaluation of the capacity of the bottom rail in partially anchored timber shear walls

OpenAIRE

Caprolu, Giuseppe; Källsner, Bo; Girhammar, Ulf Arne; Vessby, Johan

2012-01-01

Källsner and Girhammar have developed plastic design methods for light-frame timber shear walls that can be used for determining the load-carrying capacity when the shear walls are partially anchored. For such walls, the leading stud is not fully anchored against uplift and tying down forces are developed in the sheathing-to-framing joints. Since the forces in the anchor bolts and the sheathing-to-framing joints do not act in the same vertical plane, the bottom rail will be subjected to cross...

Midterm outcome of EndoAnchors for the prevention of endoleak and stent-graft migration in patients with challenging proximal aortic neck anatomy.

Science.gov (United States)

Jordan, William D; de Vries, Jean-Paul P M; Ouriel, Kenneth; Mehta, Manish; Varnagy, David; Moore, William M; Arko, Frank R; Joye, James; Henretta, John

2015-04-01

To explore the use of EndoAnchors as an adjunct to endovascular abdominal aortic aneurysm repair for prevention of proximal neck complications in patients with challenging neck anatomy. Over a 28-month period, 208 patients (159 men; mean age 72±8 years) were enrolled in the ANCHOR prospective, multicenter registry (ClinicalTrials.gov; identifier NCT01534819) for prophylaxis against proximal neck complications. Patients were eligible when, in the opinion of the investigators, they were at increased risk for type Ia endoleak or migration owing to a hostile neck (length 28 mm, angulation >60°, mural thrombus or calcium >2 mm in thickness or >180° in circumference, or conical shape). Overall, 123/157 (78.3%) patients met the criteria for a hostile neck according to core laboratory assessment of 157 adequate preoperative computed tomographic (CT) images. Implantation of EndoAnchors was technically successful in 204/208 (98.1%) patients. The frequency of fracture was 0.3% (3/1118); there were no clinical sequelae associated with the fractures. Over the mean 14-month follow-up, 95.2% of patients were alive, and no deaths were attributable to EndoAnchors. There were no ruptures, migrations, or open surgical conversions. Aneurysm-related reinterventions were performed in 8 (3.8%) patients. Among 130 patients with postprocedure contrast CT studies, core laboratory analysis identified 2 (1.5%) patients with type Ia endoleaks. Aneurysm sac diameter decreased >5 mm in 42.9% of patients with CT scans at or beyond 1 year; 1.6% of patients developed sac enlargement >5 mm. Prophylactic EndoAnchor use for challenging aortic neck anatomy was associated with satisfactory midterm results. © The Author(s) 2015.

Do violations of the axioms of expected utility theory threaten decision analysis?

Science.gov (United States)

Nease, R F

1996-01-01

Research demonstrates that people violate the independence principle of expected utility theory, raising the question of whether expected utility theory is normative for medical decision making. The author provides three arguments that violations of the independence principle are less problematic than they might first appear. First, the independence principle follows from other more fundamental axioms whose appeal may be more readily apparent than that of the independence principle. Second, the axioms need not be descriptive to be normative, and they need not be attractive to all decision makers for expected utility theory to be useful for some. Finally, by providing a metaphor of decision analysis as a conversation between the actual decision maker and a model decision maker, the author argues that expected utility theory need not be purely normative for decision analysis to be useful. In short, violations of the independence principle do not necessarily represent direct violations of the axioms of expected utility theory; behavioral violations of the axioms of expected utility theory do not necessarily imply that decision analysis is not normative; and full normativeness is not necessary for decision analysis to generate valuable insights.

A Systematic Review and Meta-analysis of Childhood Health Utilities.

Science.gov (United States)

Kwon, Joseph; Kim, Sung Wook; Ungar, Wendy J; Tsiplova, Kate; Madan, Jason; Petrou, Stavros

2018-04-01

A common feature of most reviews or catalogues of health utilities has been their focus on adult health states or derivation of values from adult populations. More generally, utility measurement in or on behalf of children has been constrained by several methodological concerns. The objective of this study was to conduct the first comprehensive systematic review and meta-analysis of primary utility data for childhood conditions and descriptors, and to determine the effects of methodological factors on childhood utilities. The review followed PRISMA guidelines. PubMed, Embase, Web of Science, PsycINFO, EconLit, CINAHL and Cochrane Library were searched for primary studies reporting health utilities for childhood conditions or descriptors using direct or indirect valuation methods. The Paediatric Economic Database Evaluation (PEDE) Porject was also searched for cost-utility analyses with primary utility values. Mean or median utilities for each of the main samples were catalogued, and weighted averages of utilities for each health condition were estimated, by valuation method. Mixed-effects meta-regression using hierarchical linear modeling was conducted for the most common valuation methods to estimate the utility decrement for each health condition category relative to general childhood population health, as well as the independent effects of methodological factors. The literature searches resulted in 272 eligible studies. These yielded 3,414 utilities when all sub-groups were considered, covering all ICD-10 chapters relevant to childhood health, 19 valuation methods, 12 respondent types, 8 modes of administration, and data from 36 countries. A total of 1,191 utility values were obtained when only main study samples were considered, and these were catalogued by health condition or descriptor, and methodological characteristics. 1,073 mean utilities for main samples were used for fixed-effects meta-analysis by health condition and valuation method. Mixed

Effects of anchoring and arc structure on the control authority of a rail plasma actuator

International Nuclear Information System (INIS)

Choi, Young-Joon; Gray, Miles; Sirohi, Jayant; Raja, Laxminarayan L

2017-01-01

Experiments were conducted on a rail plasma actuator (RailPAc) with different electrode cross sections (rails or rods) to assess methods to improve the actuation authority, defined as the impulse generated for a given electrical input. The arc was characterized with electrical measurements and high-speed images, while impulse measurements quantified the actuation authority. A RailPAc power supply capable of delivering  ∼1 kA of current at  ∼100 V was connected to rod electrodes (free-floating with circular cross-section) and rail electrodes (flush-mounted in a flat plate with rectangular cross-section). High-speed images show that the rail electrodes cause the arc to anchor itself to the anode electrode and transit in discrete jumps, while rod electrodes permit the arc to transit smoothly without anchoring. The impulse measurements reveal that the anchoring reduces the actuation authority by  ∼21% compared to a smooth transit, and the effect of anchoring can be suppressed by reducing the gap between the rails to 2 mm. The study further demonstrates that if a smooth transit is achieved, the control authority can be increased with a larger gap and larger arc current. In conclusion, the actuation authority of a RailPAc can be maximized by carefully choosing a gap width that prevents anchoring. Further study is warranted to increase the RailPAc actuation authority by introducing multiple turns of wires beneath the RailPAc to augment the induced magnetic field. (paper)

Arthroscopic Repair of Ankle Instability With All-Soft Knotless Anchors.

Science.gov (United States)

Pereira, Hélder; Vuurberg, Gwen; Gomes, Nuno; Oliveira, Joaquim Miguel; Ripoll, Pedro L; Reis, Rui Luís; Espregueira-Mendes, João; Niek van Dijk, C

2016-02-01

In recent years, arthroscopic and arthroscopically assisted techniques have been increasingly used to reconstruct the lateral ligaments of the ankle. Besides permitting the treatment of several comorbidities, arthroscopic techniques are envisioned to lower the amount of surgical aggression and to improve the assessment of anatomic structures. We describe our surgical technique for arthroscopic, two-portal ankle ligament repair using an all-soft knotless anchor, which is made exclusively of suture material. This technique avoids the need for classic knot-tying methods. Thus it diminishes the chance of knot migration caused by pendulum movements. Moreover, it avoids some complications that have been related to the use of metallic anchors and some currently available biomaterials. It also prevents prominent knots, which have been described as a possible cause of secondary complaints.

Covalent Anchoring of Chloroperoxidase and Glucose Oxidase on the Mesoporous Molecular Sieve SBA-15

Directory of Open Access Journals (Sweden)

Martin Hartmann

2010-02-01

Full Text Available Functionalization of porous solids plays an important role in many areas, including heterogeneous catalysis and enzyme immobilization. In this study, large-pore ordered mesoporous SBA-15 molecular sieves were synthesized with tetraethyl orthosilicate (TEOS in the presence of the non-ionic triblock co-polymer Pluronic P123 under acidic conditions. These materials were grafted with 3 aminopropyltrimethoxysilane (ATS, 3-glycidoxypropyltrimethoxysilane (GTS and with 3 aminopropyltrimethoxysilane and glutaraldehyde (GA-ATS in order to provide covalent anchoring points for enzymes. The samples were characterized by nitrogen adsorption, powder X-ray diffraction, solid-state NMR spectroscopy, elemental analysis, diffuse reflectance fourier transform infrared spectroscopy and diffuse reflectance UV/Vis spectroscopy. The obtained grafted materials were then used for the immobilization of chloroperoxidase (CPO and glucose oxidase (GOx and the resulting biocatalysts were tested in the oxidation of indole. It is found that enzymes anchored to the mesoporous host by the organic moieties can be stored for weeks without losing their activity. Furthermore, the covalently linked enzymes are shown to be less prone to leaching than the physically adsorbed enzymes, as tested in a fixed-bed reactor under continuous operation conditions.

Side-by-side comparison of Raman spectra of anchored and suspended carbon nanomaterials

International Nuclear Information System (INIS)

Sidorov, Anton N; Pabba, Santosh; Cohn, Robert W; Sumanasekera, G U; Hewaparakrama, Kapila P

2008-01-01

Raman spectra of ordered carbon nanomaterials are quite sensitive to surface perturbations, including trace residues, structural defects and residual stress. This is demonstrated by a series of experiments with carbon nanotubes and graphene. Their spectra change due to subtle changes in preparation and attachment to the substrate and to each other. Differences are most clearly seen by forming a material into an air bridge and probing it in the air gap and at the anchor points. A monolayer graphene sheet, shows a larger disorder band at the anchor points than in the air gap. However, a bundle or rope of parallel-aligned single-wall nanotubes shows a larger disorder band in the gap than at the anchor points. For the graphene sheet the substrate surface deforms the graphene, leading to increases in the disorder band. For the rope, the close proximity of the nanotubes to each other appears to produce a larger stress than the rope resting on the substrate

Interaction of Rupture Zones of Adjacent Anchor Plates in an Analogical Medium

Directory of Open Access Journals (Sweden)

H. Abbad

2013-12-01

Full Text Available In this paper, an experimental study which required the design and implementation of a model containing plastic granules powder to simulate a natural environment, is presented. The latter is subjected to the removal of "anchor plates." For each test, several digital photographs are taken to materialize different deformed configurations during the pullout process. These photos processed in couples by the 7D software (image correlation giving the evolution of the displacement field and plane strain analogical environment. Particular attention is paid to the discussion of the interference of rupture zones of neighboring anchors by reducing the axis between plates.

Surrogate utility estimation by long-term partners and unfamiliar dyads.

Science.gov (United States)

Tunney, Richard J; Ziegler, Fenja V

2015-01-01

To what extent are people able to make predictions about other people's preferences and values?We report two experiments that present a novel method assessing some of the basic processes in surrogate decision-making, namely surrogate-utility estimation. In each experiment participants formed dyads who were asked to assign utilities to health related items and commodity items, and to predict their partner's utility judgments for the same items. In experiment one we showed that older adults in long-term relationships were able to accurately predict their partner's wishes. In experiment two we showed that younger adults who were relatively unfamiliar with one another were also able to predict other people's wishes. Crucially we demonstrated that these judgments were accurate even after partialling out each participant's own preferences indicating that in order to make surrogate utility estimations people engage in perspective-taking rather than simple anchoring and adjustment, suggesting that utility estimation is not the cause of inaccuracy in surrogate decision-making. The data and implications are discussed with respect to theories of surrogate decision-making.

Surrogate utility estimation by long-term partners and unfamiliar dyads

Directory of Open Access Journals (Sweden)

Richard J Tunney

2015-03-01

Full Text Available To what extent are people able to make predictions about other people’s preferences and values? We report two experiments that present a novel method assessing some of the basic processes in surrogate decision-making, namely surrogate-utility estimation. In each experiment participants formed dyads who were asked to assign utilities to health related items and commodity items, and to predict their partner’s utility judgments for the same items. In experiment one we showed that older adults in long-term relationships were able to accurately predict their partner’s wishes. In experiment two we showed that younger adults who were relatively unfamiliar with one another were also able to predict other people’s wishes. Crucially we demonstrated that these judgments were accurate even after partialling out each participant’s own preferences indicating that in order to make surrogate utility estimations people engage in perspective-taking rather than simple anchoring and adjustment, suggesting that utility estimation is not the cause of inaccuracy in surrogate decision-making. The data and implications are discussed with respect to theories of surrogate decision-making.

Interpreting the Third International Mathematics and Science Study (TIMSS) achievement scales using scale anchoring

Science.gov (United States)

Kelly, Dana L.

1999-11-01

The scale anchoring method was used to analyze and describe the TIMSS primary and middle school (Populations 1 and 2) mathematics and science achievement scales. Scale anchoring is a way of attaching meaning to a scale by describing what students know and can do at specific points on the scale. Student achievement was scrutinized at four points on the TIMSS primary and middle school achievement scales---the 25th, 50th, 75th, and 90th international percentiles for fourth and eighth grades. The scale anchoring method was adapted for the TIMSS data and items that students scoring at each of the four scale points were likely to answer correctly (with a 65 percent probability) were identified. The items were assembled in binders organized by anchor level and content area. Two ten-member panels of subject-matter specialists were convened to scrutinize the items, draft descriptions of student proficiency at the four scale points, and identify example TIMSS items to illustrate performance at each level. Following the panel meetings, the descriptions were refined through an iterative review process. The result is a content-referenced interpretation of the TIMSS scales through which TIMSS achievement results can be better communicated and understood.

Age and Sex Effects in Anchoring Vignette Studies: Methodological and Empirical Contributions

Directory of Open Access Journals (Sweden)

Hanna Grol-Prokopczyk

2013-04-01

Full Text Available Anchoring vignettes are an increasingly popular tool for identifying and correcting for group differences in use of subjective ordered response categories. However, existing techniques to maximize response consistency (use of the same standards for self-ratings as for vignette-ratings, which center on matching vignette characters’ demographic characteristics to respondents’ own characteristics, appear at times to be ineffective or to pose interpretive difficulties. Specifically, respondents often appear to neglect instructions to treat vignette characters as age peers. Furthermore, when vignette characters’ sex is matched to respondents’ sex, interpretation of sex differences in rating style is rendered problematic. This study applies two experimental manipulations to a national American sample (n=1,765 to clarify best practices for enhancing response consistency. First, an analysis of two methods of highlighting vignette characters’ age suggests that both yield better response consistency than previous, less prominent means. Second, a comparison of ratings of same- and opposite-sex vignette characters suggests that, with avoidable exceptions, the sex of the respondent rather than of the vignette character drives observed sex differences in rating style. Implications for interpretation and design of anchoring vignette studies are discussed. Findings also show significant sex, educational, and racial/ethnic differences in styles of rating health, and racial/ethnic differences in styles of rating political efficacy. These findings underscore the incomparability of unadjusted subjective self-ratings across demographic groups.

Analysis of mineral phases in coal utilizing factor analysis

International Nuclear Information System (INIS)

Roscoe, B.A.; Hopke, P.K.

1982-01-01

The mineral phase inclusions of coal are discussed. The contribution of these to a coal sample are determined utilizing several techniques. Neutron activation analysis in conjunction with coal washability studies have produced some information on the general trends of elemental variation in the mineral phases. These results have been enhanced by the use of various statistical techniques. The target transformation factor analysis is specifically discussed and shown to be able to produce elemental profiles of the mineral phases in coal. A data set consisting of physically fractionated coal samples was generated. These samples were analyzed by neutron activation analysis and then their elemental concentrations examined using TTFA. Information concerning the mineral phases in coal can thus be acquired from factor analysis even with limited data. Additional data may permit the resolution of additional mineral phases as well as refinement of theose already identified

Density control of dodecamanganese clusters anchored on silicon(100).

Science.gov (United States)

Condorelli, Guglielmo G; Motta, Alessandro; Favazza, Maria; Nativo, Paola; Fragalà, Ignazio L; Gatteschi, Dante

2006-04-24

A synthetic strategy to control the density of Mn12 clusters anchored on silicon(100) was investigated. Diluted monolayers suitable for Mn12 anchoring were prepared by Si-grafting mixtures of the methyl 10-undecylenoate precursor ligand with 1-decene spectator spacers. Different ratios of these mixtures were tested. The grafted surfaces were hydrolyzed to reveal the carboxylic groups available for the subsequent exchange with the [Mn12O12(OAc)16(H2O)4]4 H2O2 AcOH cluster. Modified surfaces were analyzed by attenuated total reflection (ATR)-FTIR spectroscopy, X-ray photoemission spectroscopy (XPS), and AFM imaging. Results of XPS and ATR-FTIR spectroscopy show that the surface mole ratio between grafted ester and decene is higher than in the source solution. The surface density of the Mn12 cluster is, in turn, strictly proportional to the ester mole fraction. Well-resolved and isolated clusters were observed by AFM, using a diluted ester/decene 1:1 solution.

AKAP18:PKA-RIIα structure reveals crucial anchor points for recognition of regulatory subunits of PKA.

Science.gov (United States)

Götz, Frank; Roske, Yvette; Schulz, Maike Svenja; Autenrieth, Karolin; Bertinetti, Daniela; Faelber, Katja; Zühlke, Kerstin; Kreuchwig, Annika; Kennedy, Eileen J; Krause, Gerd; Daumke, Oliver; Herberg, Friedrich W; Heinemann, Udo; Klussmann, Enno

2016-07-01

A-kinase anchoring proteins (AKAPs) interact with the dimerization/docking (D/D) domains of regulatory subunits of the ubiquitous protein kinase A (PKA). AKAPs tether PKA to defined cellular compartments establishing distinct pools to increase the specificity of PKA signalling. Here, we elucidated the structure of an extended PKA-binding domain of AKAP18β bound to the D/D domain of the regulatory RIIα subunits of PKA. We identified three hydrophilic anchor points in AKAP18β outside the core PKA-binding domain, which mediate contacts with the D/D domain. Such anchor points are conserved within AKAPs that bind regulatory RII subunits of PKA. We derived a different set of anchor points in AKAPs binding regulatory RI subunits of PKA. In vitro and cell-based experiments confirm the relevance of these sites for the interaction of RII subunits with AKAP18 and of RI subunits with the RI-specific smAKAP. Thus we report a novel mechanism governing interactions of AKAPs with PKA. The sequence specificity of each AKAP around the anchor points and the requirement of these points for the tight binding of PKA allow the development of selective inhibitors to unequivocally ascribe cellular functions to the AKAP18-PKA and other AKAP-PKA interactions. © 2016 The Author(s). published by Portland Press Limited on behalf of the Biochemical Society.

TiO2-B Nanoribbons Anchored with NiO Nanosheets as Hybrid Anode Materials for Rechargeable Lithium ion Batteries

DEFF Research Database (Denmark)

Zhang, J. Y.; Shen, J.X.; Wang, T.L.

2015-01-01

A new type of TiO2-B nanoribbon anchored with NiO nanosheets (TiO2@NiO) is synthesized via a hydrothermal process and a subsequent homogeneous precipitation method. XRD analysis indicates that TiO2-B and cubic NiO phases exist in the composites. According to SEM images, the morphology of the TiO2...

Relation between anchorings of liquid crystals and conformation changes in aligning agents by the Langmuir-Blodgett film technique investigation

International Nuclear Information System (INIS)

Zhu, Y.; Lu, Z.; Wei, Y.

1995-01-01

The anchoring direction of liquid crystals on a solid substrate surface depends upon many parameters characterizing the liquid-crystal--substrate interface, a variation of which may change this anchoring direction leading to the so-called anchoring transition. Here, based on the Langmuir-Blodgett film technique, we present two model systems to study the relation between anchoring directions and the conformation changes in aligning agents. A double-armed crown ether liquid crystal and a side chain polymer liquid crystal at an air-water interface both show phase transitions, accompanied by conformation changes. However, when the monolayers in different phases were transferred onto solid substrates to orient liquid crystals, we found that for the crown ether material the conformation change can alter the anchoring of liquid crystals between homeotropic and homogeneous alignments, while for the polymer liquid crystal, despite the conformation changes, the liquid crystals can only be aligned homeotropically. The involved mechanisms were briefly discussed in terms of the Landau-type phenomenological theory

Stone anchors along the coast of Chilika Lake: New light on the maritime activities of Orissa, India

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.; Patnaik, A.P.

the growth of maritime trade. With increase in the carrying capacity of ships, changes made in their sizes and construction patterns, subsequently, the size and shape of the anchors also got modified. On the basis of anchor findings, an attempt has been made...

Understanding and valuing environmental issues: the effects of availability and anchoring on judgment.

Science.gov (United States)

van der Pligt, J; van Schie, E C; Hoevenagel, R

1998-01-01

This paper addresses the effects of availability and anchoring-and-adjustment on people's beliefs and values concerning environmental issues. The first three studies focus on lay people's perceptions of the causes of large scale environmental risks, the second series of three studies deals with how people value environmental goods and how much they are prepared to pay to mitigate environmental risks. In studies 1-3 we investigate the effects of availability and anchoring-and-adjustment on estimating the contribution of various factors to large scale environmental risks. Highly complex risks such as acid rain and global warming tend to be associated with multiple causes, and our results show that estimating the role of these causes is clearly affected by availability and anchoring-and-adjustment. Both have sizeable effects and persist over time. Moreover, corrective procedures only seem to have a limited effect. Availability and anchoring-and-adjustment not only play a role in judging the possible causes of risks; they also play a role in research attempting to assess the public's willingness to pay (WTP) to protect our environment. The outcomes of WTP surveys are often used as a tool to help policy decision making. In the second part of this article we present three studies on this issue. Results provide further evidence of the impact of the two heuristics on the outcomes of WTP research. Implications for research and practice are briefly discussed.

The utility of environmental exergy analysis for decision making in energy

International Nuclear Information System (INIS)

Simpson, Adam P.; Edwards, Chris F.

2013-01-01

The analysis framework discussed and employed in this paper utilizes the recent recognition that exergy is a form of environmental free energy to provide a fundamental basis for valuing environmental interactions independent from their secondary impacts. The framework is comprised of two separate components: (1) environmental exergy analysis and (2) anthropocentric sensitivity analysis. Environmental exergy analysis is based on fundamental thermodynamic principles and analysis techniques. It extends the principles of technical exergy analysis to the environment in order to quantify the location, magnitudes, and types of environmental impact—state change, alteration of natural transfers, and destruction change. Anthropocentric sensitivity analysis is based on the concepts of anthropocentric value and anthropocentric sensitivity. It enables the results of environmental exergy analysis to be interpreted for decision making, but at the expense of introducing some subjectivity into the framework. A key attribute of the framework is its ability to evaluate the environmental performance of energy systems on a level playing field, regardless of the specifics of the systems—i.e., resources consumed, products and by-products produced, or system size and time scale. The utility of the analysis framework for decision making is demonstrated in this paper through application to three example energy systems. - Highlights: ► Utilizes the recognition that exergy is a form of environmental free energy. ► Combines environmental exergy analysis and anthropocentric sensitivity analysis. ► Evaluates/compares environmental performance of systems on a level playing field. ► Independence from the system specifics—resources, by-products, sizes, time scales. ► Utility for decision making is demonstrated using real and notional energy systems

Phospholipase D specific for the phosphatidylinositol anchor of cell-surface proteins is abundant in plasma

International Nuclear Information System (INIS)

Low, M.G.; Prasad, A.R.S.

1988-01-01

An enzyme activity capable of degrading the glycosyl-phosphatidylinositol membrane anchor of cell-surface proteins has previously been reported in a number of mammalian tissues. The experiments reported here demonstrate that this anchor-degrading activity is also abundant in mammalian plasma. The activity was inhibited by EGTA or 1,10-phenanthroline. It was capable of removing the anchor from alkaline phosphatase, 5'-nucleotidase, and variant surface glycoprotein but had little or no activity toward phosphatidylinositol or phosphatidylcholine. Phosphatidic acid was the only 3 H-labeled product when this enzyme hydrolyzed [ 3 H]myristate-labeled variant surface glycoprotein. It could be distinguished from the Ca 2 =-dependent inositol phospholipid-specific phospholipase C activity in several rat tissues on the basis of its molecular size and its sensitivity to 1,10-phenanthroline. The data therefore suggest that this activity is due to a phospholipase D with specificity for glycosylphosphatidylinositol structures. Although the precise physiological function of this anchor-specific phospholipase D remains to be determined, these findings indicate that it could play an important role in regulating the expression and release of cell-surface proteins in vivo

Technical Note: Drifting vs. anchored flux chambers for measuring greenhouse gas emissions from running waters

Science.gov (United States)

Lorke, A.; Bodmer, P.; Noss, C.; Alshboul, Z.; Koschorreck, M.; Somlai, C.; Bastviken, D.; Flury, S.; McGinnis, D. F.; Maeck, A.; Müller, D.; Premke, K.

2015-09-01

Stream networks were recently discovered as major but poorly constrained natural greenhouse gas (GHG) sources. A fundamental problem is that several measurement approaches have been used without cross comparisons. Flux chambers represent a potentially powerful methodological approach if robust and reliable ways to use chambers on running water can be defined. Here we compare the use of anchored and freely drifting chambers on various streams having different flow velocities. The study clearly shows that (1) drifting chambers have a very small impact on the water turbulence under the chamber and thus generate more reliable fluxes, (2) anchored chambers enhance turbulence under the chambers and thus elevate fluxes, (3) the bias of the anchored chambers greatly depends on chamber design and sampling conditions, and (4) there is a promising method to reduce the bias from anchored chambers by using a flexible plastic foil seal to the water surface rather than having rigid chamber walls penetrating into the water. Altogether, these results provide novel guidance on how to apply flux chambers in running water, which will have important consequences for measurements to constrain the global GHG balances.

Technical note: drifting versus anchored flux chambers for measuring greenhouse gas emissions from running waters

Science.gov (United States)

Lorke, A.; Bodmer, P.; Noss, C.; Alshboul, Z.; Koschorreck, M.; Somlai-Haase, C.; Bastviken, D.; Flury, S.; McGinnis, D. F.; Maeck, A.; Müller, D.; Premke, K.

2015-12-01

Stream networks have recently been discovered to be major but poorly constrained natural greenhouse gas (GHG) sources. A fundamental problem is that several measurement approaches have been used without cross-comparisons. Flux chambers represent a potentially powerful methodological approach if robust and reliable ways to use chambers on running water can be defined. Here we compare the use of anchored and freely drifting chambers on various streams with different flow velocities. The study clearly shows that (1) anchored chambers enhance turbulence under the chambers and thus elevate fluxes, (2) drifting chambers have a very small impact on the water turbulence under the chamber and thus generate more reliable fluxes, (3) the bias of the anchored chambers greatly depends on chamber design and sampling conditions, and (4) there is a promising method to reduce the bias from anchored chambers by using a flexible plastic foil collar to seal the chambers to the water surface, rather than having rigid chamber walls penetrating into the water. Altogether, these results provide novel guidance on how to apply flux chambers in running water, which will have important consequences for measurements to constrain the global GHG balances.

High-throughput physical map anchoring via BAC-pool sequencing

Czech Academy of Sciences Publication Activity Database

Cviková, Kateřina; Cattonaro, F.; Alaux, M.; Stein, N.; Mayer, K.F.X.; Doležel, Jaroslav; Bartoš, Jan

2015-01-01

Roč. 15, APR 11 (2015) ISSN 1471-2229 R&D Projects: GA ČR GA13-08786S; GA MŠk(CZ) LO1204 Institutional support: RVO:61389030 Keywords : Physical map * Contig anchoring * Next generation sequencing Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 3.631, year: 2015

Approaches to enhance body-anchored and experience-based learning

DEFF Research Database (Denmark)

Stelter, Reinhard

2008-01-01

in the rhythm and intentional orientation can also be applied to different areas, for example, psychotherapy or coaching. But the main focus is on examples from physical education. The final part of the article sees body-anchored learning as integrated in a cultural setting and as part of learning...

Retractable Robotic Anchor for Hard Rock and Granular Soils, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — ProtoInnovations proposes to research, develop, and validate an innovative retractable robotic anchoring mechanism that works both in hard rock and granular soils...

Skilled delivery care service utilization in Ethiopia: analysis of rural ...

African Journals Online (AJOL)

Only 4.5% women in rural areas received assistance from skilled birth attendants (SBAs) compared to 64.1 % of their urban counter parts. Through Bayesian logistic regression analysis, place of residence, ANC utilization, women's education, age and birth order were identified as key predictors of service utilization.

Percutaneous Transcholecystic Biliary Interventions Using Gallbladder Anchors: Feasibility Study in the Swine

International Nuclear Information System (INIS)

Lopera, Jorge E.; Kirsch, David; Qian Zhong; Ruiz, Bernardo; Brazzini, Augusto; Gonzales, Arturo; Castaneda-Zuniga, Wilfrido

2005-01-01

The purpose of this study was to report our initial experience with a swine model for biliary interventions by using a percutaneous transcholecystic access after suture anchor of the gallbladder. Telepaque tablets were given to five pigs to opacify the gallbladder. Under fluoroscopy, the opacified gallbladder was punctured percutaneously and three suture anchors were used to fix the anterior wall of the gallbladder to the abdominal wall. Two weeks later, the gallbladder was punctured and access into the distal common bile was obtained through the cystic duct. Balloon expandable stents were deployed into the distal common bile duct. Follow-up cholangiograms were obtained at 1 and 2 weeks. Necropsy was performed after 2 weeks to evaluate the relationship between the gallbladder and abdominal wall. Suture anchor placement was successful in all five pigs. One pig with a deep and highly positioned gallbladder developed fever, anorexia, and vomiting secondary to excessive stretch of the gallbladder. Placement of the guidewire through the extremely tortuous and small cystic ducts proved to be the most challenging step of the procedure. Metallic stents were successfully deployed in all four pigs in which it was attempted. Four animals tolerated the procedures without changes in their clinical conditions and no symptoms. Successful follow-up cholangiograms were performed at 1 and 2 weeks post-stent deployment without complications. All stents remained patent during the follow-up period. Necropsy demonstrated close attachment and adherence of the gallbladders to the antero-lateral abdominal wall in all four animals. Suture anchoring of the gallbladder is feasible in most pigs with superficially located gallbladders. This technique allows a safe and repeat access into the biliary system using a transcholecystic approach

Biomechanical comparison of a single-row versus double-row suture anchor technique for rotator cuff repair.

Science.gov (United States)

Kim, David H; Elattrache, Neal S; Tibone, James E; Jun, Bong-Jae; DeLaMora, Sergai N; Kvitne, Ronald S; Lee, Thay Q

2006-03-01

Reestablishment of the native footprint during rotator cuff repair has been suggested as an important criterion for optimizing healing potential and fixation strength. A double-row rotator cuff footprint repair will demonstrate superior biomechanical properties compared with a single-row repair. Controlled laboratory study. In 9 matched pairs of fresh-frozen cadaveric shoulders, the supraspinatus tendon from 1 shoulder was repaired with a double-row suture anchor technique: 2 medial anchors with horizontal mattress sutures and 2 lateral anchors with simple sutures. The tendon from the contralateral shoulder was repaired using a single lateral row of 2 anchors with simple sutures. Each specimen underwent cyclic loading from 10 to 180 N for 200 cycles, followed by tensile testing to failure. Gap formation and strain over the footprint area were measured using a video digitizing system; stiffness and failure load were determined from testing machine data. Gap formation for the double-row repair was significantly smaller (P row repair for the first cycle (1.67 +/- 0.75 mm vs 3.10 +/- 1.67 mm, respectively) and the last cycle (3.58 +/- 2.59 mm vs 7.64 +/- 3.74 mm, respectively). The initial strain over the footprint area for the double-row repair was nearly one third (P row repair. Adding a medial row of anchors increased the stiffness of the repair by 46% and the ultimate failure load by 48% (P row repair improved initial strength and stiffness and decreased gap formation and strain over the footprint when compared with a single-row repair. To achieve maximal initial fixation strength and minimal gap formation for rotator cuff repair, reconstructing the footprint attachment with 2 rows of suture anchors should be considered.

Differences regarding job satisfaction and job involvement of psychologists with different dominant career anchors

OpenAIRE

CL Bester; T Mouton

2006-01-01

In order to contribute to higher levels of job satisfaction, job involvement , and productivity, a match or fit should be established between the dominant career anchor associated with a specific occupation and that of the employee. A career anchor is an individual’s set of self-perceived talents, abilities, motives, needs and values that form the nucleus of one’s occupational self-concept. Psychologists have always been part of the service orientated careers and therefore one would expect th...

Aggregate Effect on the Concrete Cone Capacity of an Undercut Anchor under Quasi-Static Tensile Load.

Science.gov (United States)

Marcon, Marco; Ninčević, Krešimir; Boumakis, Ioannis; Czernuschka, Lisa-Marie; Wan-Wendner, Roman

2018-05-01

In the last decades, fastening systems have become an essential part of the construction industry. Post-installed mechanical anchors are frequently used in concrete members to connect them with other load bearing structural members, or to attach appliances. Their performance is limited by the concrete related failure modes which are highly influenced by the concrete mix design. This paper aims at investigating the effect that different aggregates used in the concrete mix have on the capacity of an undercut anchor under tensile quasi-static loading. Three concrete batches were cast utilising three different aggregate types. For two concrete ages (28 and 70 days), anchor tensile capacity and concrete properties were obtained. Concrete compressive strength, fracture energy and elastic modulus are used to normalize and compare the undercut anchor concrete tensile capacity employing some of the most widely used prediction models. For a more insightful comparison, a statistical method that yields also scatter information is introduced. Finally, the height and shape of the concrete cones are compared by highly precise and objective photogrammetric means.

SiC2 siligraphene as a promising anchoring material for lithium-sulfur batteries: a computational study

Science.gov (United States)

Zhao, Yuming; Zhao, Jingxiang; Cai, Qinghai

2018-05-01

The development of stable and effective anchoring materials to immobilize the soluble lithium polysulfide (Li2Sn) species for suppressing their shuttle effects is vital for the large-scale practical applications of lithium-sulfur (Li-S) batteries. Here, by means of density functional theory (DFT) computations, the potential applications of the experimentally available SiC2 siligraphene (g-SiC2) as an anchoring material of Li-S batteries are systemically investigated. Our results reveal that g-SiC2 exhibits remarkable but not strong binding strength for the soluble Li2Sn species due to the S-Si and Li-C interactions. Especially, the intactness of the Li2Sn species and the good conductance of g-SiC2 can be well preserved after anchoring the Li2Sn species. The further comparative research demonstrate that g-SiC2 is superior to other siligraphenes, enabling it to be a very promising material as an ideal anchoring material for the immobilization of soluble Li2Sn species to avoid their dissolution into electrolyte.

4D modeling in a gimbaled linear accelerator by using gold anchor markers.

Science.gov (United States)

Miura, Hideharu; Ozawa, Shuichi; Matsuura, Takaaki; Kawakubo, Atsushi; Hosono, Fumika; Yamada, Kiyoshi; Nagata, Yasushi

2018-01-01

The purpose of this study was to verify whether the dynamic tumor tracking (DTT) feature of a Vero4DRT system performs with 10-mm-long and 0.28 mm diameter gold anchor markers. Gold anchor markers with a length of 10 mm and a diameter of 0.28 mm were used. Gold anchor markers were injected with short and long types into bolus material. These markers were sandwiched by a Tough Water (TW) phantom in the bolus material. For the investigation of 4-dimensional (4D) modeling feasibility under various phantom thicknesses, the TW phantom was added at 2 cm intervals (in upper and lower each by 1 cm). A programmable respiratory motion table was used to simulate breathing-induced organ motion, with an amplitude of 30 mm and a breathing cycle of 3 s. X-ray imaging parameters of 80 kV and 125 kV (320 mA and 5 ms) were used. The least detection error of the fiducial marker was defined as the 4D-modeling limitation. The 4D modeling process was attempted using short and long marker types and its limitation with the short and long types was with phantom thicknesses of 6 and 10 cm at 80 kV and 125 kV, respectively. However, the loss in detectability of the gold anchor because of 4D-modeling errors was found to be approximately 6% (2/31) with a phantom thickness of 2 cm under 125 kV. 4D-modeling could be performed except under the described conditions. This work showed that a 10-mm-long gold anchor marker in short and long types can be used with DTT for short water equivalent path length site, such as lung cancer patients, in the Vero4DRT system.

Radiolucent rings around bioabsorbable anchors after rotator cuff repair are not associated with clinical outcomes.

Science.gov (United States)

Park, Jin-Young; Jang, Suk-Hwan; Oh, Kyung-Soo; Li, Yi Jin

2017-11-01

Various researchers have observed small areas of osteolysis after using bioabsorbable anchors in shoulder surgeries. The purpose of this study is to determine whether radiographic perianchor radiolucent rings after rotator cuff repair are associated with the failure of repair and also assess their clinical implications. Further, the most frequent location of the radiolucent rings in the double-row suture bridge configuration was also assessed. One hundred and twenty-nine consecutive patients who underwent arthroscopic rotator cuff repair by suture bridge technique were retrospectively evaluated radiographically and clinically. The number and size of the rings that appeared at each follow-up were recorded. Also, the locations of each ring were recorded as anterior, middle or posterior, and medial or lateral according to the construct of the anchors used for suture bridge technique. The size of the tear, the number of anchors used and age of the patients were compared. Re-tear rates according to ultrasound examinations were also analyzed. After rotator cuff repair, the mean American Shoulder and Elbow Surgeons (ASES) score increased from 46.7 to 88.0 and the overall re-tear rate was 8.5% (11 cases). Seventy-three patients (56.6%) showed RR (total number of 99 rings) at least once during the course of their follow-up and the rings appeared at a mean period of 18.2 months after surgery. Mean size of the rings initially was 5.6 mm and the rings increased or decreased in mean size of 0.4 mm during mean follow-up of 37 months. No correlation was seen with the number of RRs and the rate of re-tears, number of anchors, size of tears, and clinical outcome as determined by the ASES score. Radiolucent ring measurement reproducibility was confirmed by independent, repeated measurements. The rings appeared mostly at anteromedial anchors (75 rings, 75.8%) and the authors suggest that mechanical factors may play a role for the cause of radiolucent rings. The number and the

Effects of the anchor system on postural control in older Adults

Directory of Open Access Journals (Sweden)

Eliane Mauerberg de Castro

2012-03-01

Full Text Available Falls are common during aging, and can have drastic consequences. Within this context, maintaining the ability to balance plays an essential role in enabling older adults to continue to perform their daily activities. Therefore, the use of interventional and treatment tools for development of balance becomes essential. The objective of this study was to analyze the anchor system as a potential tool for decreasing body sway in older and young adults. Older adults had more postural sway than their young counterparts. The absence of visual information led to larger instability in both groups. The anchor system improved postural stability of both groups. Thus, it may be a useful tool for posture stabilization in old and young adults.

Poor Anchoring Limits Dyslexics' Perceptual, Memory, and Reading Skills

Science.gov (United States)

Oganian, Yulia; Ahissar, Merav

2012-01-01

The basic deficits underlying the severe and persistent reading difficulties in dyslexia are still highly debated. One of the major topics of debate is whether these deficits are language specific, or affect both verbal and non-verbal stimuli. Recently, Ahissar and colleagues proposed the "anchoring-deficit hypothesis" (Ahissar, Lubin,…

A Tenebrio molitor GPI-anchored alkaline phosphatase is involved in binding of Bacillus thuringiensis Cry3Aa to brush border membrane vesicles.

Science.gov (United States)

Zúñiga-Navarrete, Fernando; Gómez, Isabel; Peña, Guadalupe; Bravo, Alejandra; Soberón, Mario

2013-03-01

Bacillus thuringiensis Cry toxins recognizes their target cells in part by the binding to glycosyl-phosphatidyl-inositol (GPI) anchored proteins such as aminopeptidase-N (APN) or alkaline phosphatases (ALP). Treatment of Tenebrio molitor brush border membrane vesicles (BBMV) with phospholipase C that cleaves out GPI-anchored proteins from the membranes, showed that GPI-anchored proteins are involved in binding of Cry3Aa toxin to BBMV. A 68 kDa GPI-anchored ALP was shown to bind Cry3Aa by toxin overlay assays. The 68 kDa GPI-anchored ALP was preferentially expressed in early instar larvae in comparison to late instar larvae. Our work shows for the first time that GPI-anchored ALP is important for Cry3Aa binding to T. molitor BBMV suggesting that the mode of action of Cry toxins is conserved in different insect orders. Copyright © 2012 Elsevier Inc. All rights reserved.

Biomechanical comparison of an all-soft suture anchor with a modified Broström-Gould suture repair for lateral ligament reconstruction.

Science.gov (United States)

Brown, Christopher A; Hurwit, Daniel; Behn, Anthony; Hunt, Kenneth J

2014-02-01

Anatomic repair is indicated for patients who have recurrent lateral ankle instability despite nonoperative measures. There is no difference in repair stiffness, failure torque, or failure angle between specimens repaired with all-soft suture anchors versus the modified Broström-Gould technique with sutures only. Controlled laboratory study. In 10 matched pairs of human cadaveric ankles, the anterior talofibular ligament (ATFL) was incised from its origin on the fibula. After randomization, 1 ankle was repaired to its anatomic insertion using two 1.4-mm JuggerKnot all-soft suture anchors; the other ankle was repaired with a modified Broström-Gould technique using 2-0 FiberWire. All were augmented using the inferior extensor retinaculum. All ankles were mounted to the testing machine in 20° of plantar flexion and 15° of internal rotation and loaded to failure after the repair. Stiffness, failure torque, and failure angle were recorded and compared using a paired Student t test with a significance level set at P anchors pulled out of bone. The primary mode of failure was pulling through the ATFL tissue. There was no statistical difference in strength or stiffness between a 1.4-mm all-soft suture anchor and a modified Broström-Gould repair with 2-0 FiberWire. The primary mode of failure was at the tissue level rather than knot failure or anchor pullout. The particular implant choice (suture only, tunnel, anchor) in repairing the lateral ligament complex may not be as important as the time to biological healing. The suture-only construct as described in the Broström-Gould repair was as strong as all-soft suture anchors, and the majority of the ankles failed at the tissue level. For those surgeons whose preference is to use anchor repair, this novel all-soft suture anchor may be an alternative to other larger anchors, as none failed by pullout.

Progress on Poverty? New Estimates of Historical Trends Using an Anchored Supplemental Poverty Measure

Science.gov (United States)

Wimer, Christopher; Fox, Liana; Garfinkel, Irwin; Kaushal, Neeraj; Waldfogel, Jane

2016-01-01

This study examines historical trends in poverty using an anchored version of the U.S. Census Bureau’s recently developed Research Supplemental Poverty Measure (SPM) estimated back to 1967. Although the SPM is estimated each year using a quasi-relative poverty threshold that varies over time with changes in families’ expenditures on a core basket of goods and services, this study explores trends in poverty using an absolute, or anchored, SPM threshold. We believe the anchored measure offers two advantages. First, setting the threshold at the SPM’s 2012 levels and estimating it back to 1967, adjusted only for changes in prices, is more directly comparable to the approach taken in official poverty statistics. Second, it allows for a better accounting of the roles that social policy, the labor market, and changing demographics play in trends in poverty rates over time, given that changes in the threshold are held constant. Results indicate that unlike official statistics that have shown poverty rates to be fairly flat since the 1960s, poverty rates have dropped by 40 % when measured using a historical anchored SPM over the same period. Results obtained from comparing poverty rates using a pretax/pretransfer measure of resources versus a posttax/posttransfer measure of resources further show that government policies, not market incomes, are driving the declines observed over time. PMID:27352076

Progress on Poverty? New Estimates of Historical Trends Using an Anchored Supplemental Poverty Measure.

Science.gov (United States)

Wimer, Christopher; Fox, Liana; Garfinkel, Irwin; Kaushal, Neeraj; Waldfogel, Jane

2016-08-01

This study examines historical trends in poverty using an anchored version of the U.S. Census Bureau's recently developed Research Supplemental Poverty Measure (SPM) estimated back to 1967. Although the SPM is estimated each year using a quasi-relative poverty threshold that varies over time with changes in families' expenditures on a core basket of goods and services, this study explores trends in poverty using an absolute, or anchored, SPM threshold. We believe the anchored measure offers two advantages. First, setting the threshold at the SPM's 2012 levels and estimating it back to 1967, adjusted only for changes in prices, is more directly comparable to the approach taken in official poverty statistics. Second, it allows for a better accounting of the roles that social policy, the labor market, and changing demographics play in trends in poverty rates over time, given that changes in the threshold are held constant. Results indicate that unlike official statistics that have shown poverty rates to be fairly flat since the 1960s, poverty rates have dropped by 40 % when measured using a historical anchored SPM over the same period. Results obtained from comparing poverty rates using a pretax/pretransfer measure of resources versus a post-tax/post-transfer measure of resources further show that government policies, not market incomes, are driving the declines observed over time.

Cell wall-anchored nuclease of Streptococcus sanguinis contributes to escape from neutrophil extracellular trap-mediated bacteriocidal activity.

Directory of Open Access Journals (Sweden)

Chisato Morita

Full Text Available Streptococcus sanguinis, a member of the commensal mitis group of streptococci, is a primary colonizer of the tooth surface, and has been implicated in infectious complications including bacteremia and infective endocarditis. During disease progression, S. sanguinis may utilize various cell surface molecules to evade the host immune system to survive in blood. In the present study, we discovered a novel cell surface nuclease with a cell-wall anchor domain, termed SWAN (streptococcal wall-anchored nuclease, and investigated its contribution to bacterial resistance against the bacteriocidal activity of neutrophil extracellular traps (NETs. Recombinant SWAN protein (rSWAN digested multiple forms of DNA including NET DNA and human RNA, which required both Mg(2+ and Ca(2+ for optimum activity. Furthermore, DNase activity of S. sanguinis was detected around growing colonies on agar plates containing DNA. In-frame deletion of the swan gene mostly reduced that activity. These findings indicated that SWAN is a major nuclease displayed on the surface, which was further confirmed by immuno-detection of SWAN in the cell wall fraction. The sensitivity of S. sanguinis to NET killing was reduced by swan gene deletion. Moreover, heterologous expression of the swan gene rendered a Lactococcus lactis strain more resistant to NET killing. Our results suggest that the SWAN nuclease on the bacterial surface contributes to survival in the potential situation of S. sanguinis encountering NETs during the course of disease progression.

Cell wall-anchored nuclease of Streptococcus sanguinis contributes to escape from neutrophil extracellular trap-mediated bacteriocidal activity.

Science.gov (United States)

Morita, Chisato; Sumioka, Ryuichi; Nakata, Masanobu; Okahashi, Nobuo; Wada, Satoshi; Yamashiro, Takashi; Hayashi, Mikako; Hamada, Shigeyuki; Sumitomo, Tomoko; Kawabata, Shigetada

2014-01-01

Streptococcus sanguinis, a member of the commensal mitis group of streptococci, is a primary colonizer of the tooth surface, and has been implicated in infectious complications including bacteremia and infective endocarditis. During disease progression, S. sanguinis may utilize various cell surface molecules to evade the host immune system to survive in blood. In the present study, we discovered a novel cell surface nuclease with a cell-wall anchor domain, termed SWAN (streptococcal wall-anchored nuclease), and investigated its contribution to bacterial resistance against the bacteriocidal activity of neutrophil extracellular traps (NETs). Recombinant SWAN protein (rSWAN) digested multiple forms of DNA including NET DNA and human RNA, which required both Mg(2+) and Ca(2+) for optimum activity. Furthermore, DNase activity of S. sanguinis was detected around growing colonies on agar plates containing DNA. In-frame deletion of the swan gene mostly reduced that activity. These findings indicated that SWAN is a major nuclease displayed on the surface, which was further confirmed by immuno-detection of SWAN in the cell wall fraction. The sensitivity of S. sanguinis to NET killing was reduced by swan gene deletion. Moreover, heterologous expression of the swan gene rendered a Lactococcus lactis strain more resistant to NET killing. Our results suggest that the SWAN nuclease on the bacterial surface contributes to survival in the potential situation of S. sanguinis encountering NETs during the course of disease progression.

Summary of the fourth conference on United States utility experience in reactor noise analysis

International Nuclear Information System (INIS)

Fry, D.N.

1987-01-01

The fourth informal conference on United States utility experience in reactor noise analysis and loose-part monitoring was held at the Northeast Utilities Service Company offices in Hartford, Connecticut, May 12-14, 1987. Host and general chairman for the meeting was J.V. Persio of Northeast Utilities. This conference provided a forum where utilities could share information on reactor noise analysis on an informal basis. There were about 60 attendees at the meeting representing 10 utilities, 3 reactor vendors, 8 consulting organizations, and 4 universities and research laboratories. Twenty-three papers were presented at the conference, dealing with various aspects of loose-part monitoring, neutron noise analysis, and standards activities

Spectroscopic and first principles investigation on 4-[(4-pyridinylmethylene)amino]-benzoic acid bearing pyridyl and carboxyl anchoring groups

Science.gov (United States)

Zhang, Lei; Wang, Qiaoyi

2018-03-01

We report a combined experimental and computational investigation on the structure and photophysics of 4-[(4-pyridinylmethylene)amino]-benzoic acid, a functional molecule bearing two anchoring groups for attachment onto a TiO2 surface and perovskite surface, for potential solar cell application. This molecule possesses interesting adsorption properties in perovskite solar cell because the pyridyl group serves as the Lewis base and targets Lewis acidic sites in the perovskite surface, while the carboxyl group targets TiO2 surface, improving the coupling between the perovskite surface and the TiO2 surface. The electronic structures of the molecule and its photochemistry are revealed by the UV-vis absorption spectra and the fluorescence spectra under visible light irradiation, which are combined with density functional theory (DFT) and time-dependent density functional theory (TDDFT) analysis. Considering the bi-anchoring groups and the conjugated π system embedded in the molecule, we anticipate it can molecular engineer the TiO2/perovskite interface in perovskite solar cell.

Influence of anchoring on miscarriage risk perception associated with amniocentesis.

Science.gov (United States)

Nuccio, Regina; Hashmi, S Shahrukh; Mastrobattista, Joan; Noblin, Sarah Jane; Refuerzo, Jerrie; Smith, Janice L; Singletary, Claire N

2015-04-01

One factor women consider when deciding whether to pursue amniocentesis is the risk of miscarriage. People use mechanisms like anchoring, or the prior belief regarding the magnitude of risk, as a frame of reference for new information. This study aimed to determine a woman's perception of miscarriage risk associated with amniocentesis before and after genetic counseling and to determine what factors anchor a woman's perception of miscarriage risk. One hundred thirteen women being seen for prenatal genetic counseling and possible amniocentesis at six Houston clinics participated in the two-part anonymous survey. While most women (56.7 %) perceived the risk as low or average pre-counseling and indicated the numeric risk of amniocentesis as risk as risk perception did not change after the genetic counseling session (60 %). Those who changed their feeling about the risk after counseling showed a decreased perception of the risk (p perception of the risk (p = 0.017) whereas those who declined amniocentesis were more likely to view the risk as high (p = 0.004). The only two anchoring factors that had an effect were having a friend or relative with a personal or family history of a genetic disorder (p = 0.001) and having a child already (p = 0.038); both were associated with a lower risk perception. The lack of significant factors may reflect the uniqueness of each patient's risk assessment framework and reinforces the importance of genetic counseling to elucidate individual concerns, particularly as non-invasive prenatal testing becomes more widely available and further complicates the prenatal testing landscape.

Treatment of chronic deltoid ligament injury using suture anchors.

Science.gov (United States)

Wang, Xu; Ma, Xin; Zhang, Chao; Wang, Chen; Huang, Jia-zhang

2014-08-01

To explore the efficacy of overlapping suture-anchor fixation for treatment of chronic deltoid ligament injury. Seventeen patients (11 men, 6 women of mean age 32.1 years [range, 18-58 years]) who had undergone surgery for chronic deltoid ligament injury from January 2007 to December 2011 were retrospectively analyzed. Preoperatively, they had undergone bilateral weight-bearing posterior-anterior radiographs, (MRI) and ultrasound examinations of the ankle. Ankle arthroscopy was performed to confirm the diagnosis, followed by surgery to clear intra-articular proliferating synovial tissues and remove cartilage debris and scar tissue. The deep layer of the deltoid ligament was sutured onto the tip of the medial malleolus and its superficial layer sutured onto its periosteum and fixed with suture anchors. American Orthopedic Foot and Ankle Society (AOFAS) scoring system for the ankle-hindfoot was used to evaluate the ankles pre- and post-operatively. The 17 patients were followed up for 12-34 months (mean 20.1 months). The angle between the long axes of the talus and first metatarsal and the hindfoot angle measured in a hindfoot alignment view (as described by Saltzman) were reduced from 5.4° ± 1.8° and 8.2° ± 2.6° preoperatively to 4.0° ± 0.9° and 5.3° ± 1.3° postoperatively, respectively. The mean AOFAS ankle-hindfoot score was 76.8 ± 7.0 preoperatively and 94.1 ± 3.3 at the last follow-up visit. Ten patients were scored as excellent, six as good, and one as fair. Pain was relieved in all patients and no patients had recurrent deltoid ligament injury. Using suture anchors to treat chronic deltoid ligament injury has relatively satisfactory outcomes. © 2014 Chinese Orthopaedic Association and Wiley Publishing Asia Pty Ltd.

Silver nanoparticles anchored reduced graphene oxide for enhanced electrocatalytic activity towards methanol oxidation

Science.gov (United States)

Kumar, Sanjeev; Mahajan, Mani; Singh, Rajinder; Mahajan, Aman

2018-02-01

In this report, silver nanoparticles (Ag NPs) anchored reduced graphene oxide (rGO) sheets (rGO/Ag) nanohybrid has been explored as anode material in direct methanol fuel cells (DMFCs). The synthesized rGO/Ag nanohybrid is characterized by XRD, XPS, FTIR spectroscopy and HRTEM techniques. Cyclic voltammograms demonstrate that the rGO/Ag nanohybrid exhibits higher electrocatalytic activity in comparison to rGO sheets for methanol oxidation reaction (MOR). This enhancement is attributed to the synergetic effect produced by the presence of more active sites provided by Ag NPs anchored on a conducting network of large surface area rGO sheets.

Psychological career resources as predictors of working adults’ career anchors: An exploratory study

Directory of Open Access Journals (Sweden)

Melinde Coetzee

2009-07-01

Full Text Available This study explored the relationship between the psychological career resources and career anchors of a sample of 2 997 working adults at predominantly managerial and supervisory levels in the service industry. The Psychological Career Resources Inventory and the Career Orientations Inventory were applied. Stepwise regression analyses indicated dimensions of psychological career resources as significant predictors of  participants’ career anchors. The findings add valuable new knowledge that can be used to inform organisational career development support practices as well as career counselling and guidance services concerned with promoting individuals’ employability and experiences of intrinsic career success.

Design of Ru(II) sensitizers endowed by three anchoring units for adsorption mode and light harvesting optimization

International Nuclear Information System (INIS)

Lobello, Maria Grazia; Fantacci, Simona; Manfredi, Norberto; Coluccini, Carmine; Abbotto, Alessandro; Nazeeruddin, Mohammed K.; De Angelis, Filippo

2014-01-01

We report the design, synthesis and computational investigation of a class of Ru(II)-dyes based on mixed bipyridine ligands for use in dye-sensitized solar cells. These dyes are designed to preserve the optimal anchoring mode of the prototypical N719 sensitizer by three carboxylic groups, yet allowing for tunable optimization of their electronic and optical properties by selective substitution at one of the 4-4′ positions of a single bipyridine ligand with π-excessive heteroaromatic groups. We used Density Functional Theory/Time Dependent Density Functional Theory calculations to analyze the electronic structure and optical properties of the dye and to investigate the dye adsorption mode on a TiO 2 nanoparticle model. Our results show that we are effectively able to introduce three carboxylic anchoring units into the dye and achieve at the same time an enhanced dye light harvesting, demonstrating the design concept. As a drawback of this type of dyes, the synthesis leads to a mixture of dye isomers, which are rather tedious to separate. - Highlights: • We designed heteroleptic Ru(II) sensitizers with three carboxylic anchoring groups. • The three carboxylic anchoring groups are essential for high open circuit potentials. • Introduction of the mixed bipyridine ligand increases the dye light absorption. • Computational simulations confirm the three anchoring sites on TiO 2

Design of Ru(II) sensitizers endowed by three anchoring units for adsorption mode and light harvesting optimization

Energy Technology Data Exchange (ETDEWEB)

Lobello, Maria Grazia; Fantacci, Simona [Computational Laboratory for Hybrid/Organic Photovoltaics (CLHYO), Istituto CNR di Scienze e Tecnologie Molecolari, Via elce di Sotto 8, I-06213 Perugia (Italy); Manfredi, Norberto; Coluccini, Carmine [Department of Materials Science and Milano-Bicocca Solar Energy Research Center-MIB-Solar, University of Milano-Bicocca and INSTM, Via Cozzi 53, I-20125 Milano (Italy); Abbotto, Alessandro, E-mail: alessandro.abbotto@unimib.it [Department of Materials Science and Milano-Bicocca Solar Energy Research Center-MIB-Solar, University of Milano-Bicocca and INSTM, Via Cozzi 53, I-20125 Milano (Italy); Nazeeruddin, Mohammed K., E-mail: mdkhaja.nazeeruddin@epfl.ch [Laboratory for Photonics and Interfaces, Station 6, Institute of Chemical Sciences and Engineering, School of Basic Sciences, Swiss Federal Institute of Technology, CH-1015 Lausanne (Switzerland); De Angelis, Filippo, E-mail: filippo@thch.unipg.it [Computational Laboratory for Hybrid/Organic Photovoltaics (CLHYO), Istituto CNR di Scienze e Tecnologie Molecolari, Via elce di Sotto 8, I-06213 Perugia (Italy)

2014-06-02

We report the design, synthesis and computational investigation of a class of Ru(II)-dyes based on mixed bipyridine ligands for use in dye-sensitized solar cells. These dyes are designed to preserve the optimal anchoring mode of the prototypical N719 sensitizer by three carboxylic groups, yet allowing for tunable optimization of their electronic and optical properties by selective substitution at one of the 4-4′ positions of a single bipyridine ligand with π-excessive heteroaromatic groups. We used Density Functional Theory/Time Dependent Density Functional Theory calculations to analyze the electronic structure and optical properties of the dye and to investigate the dye adsorption mode on a TiO{sub 2} nanoparticle model. Our results show that we are effectively able to introduce three carboxylic anchoring units into the dye and achieve at the same time an enhanced dye light harvesting, demonstrating the design concept. As a drawback of this type of dyes, the synthesis leads to a mixture of dye isomers, which are rather tedious to separate. - Highlights: • We designed heteroleptic Ru(II) sensitizers with three carboxylic anchoring groups. • The three carboxylic anchoring groups are essential for high open circuit potentials. • Introduction of the mixed bipyridine ligand increases the dye light absorption. • Computational simulations confirm the three anchoring sites on TiO{sub 2}.

Glycosylphosphatidylinositol-Anchored Proteins in Fusarium graminearum: Inventory, Variability, and Virulence

Science.gov (United States)

Rittenour, William R.; Harris, Steven D.

2013-01-01

The contribution of cell surface proteins to plant pathogenicity of fungi is not well understood. As such, the objective of this study was to investigate the functions and importance of glycosylphosphatidylinositol-anchored proteins (GPI-APs) in the wheat pathogen F. graminearum. GPI-APs are surface proteins that are attached to either the membrane or cell wall. In order to simultaneously disrupt several GPI-APs, a phosphoethanolamine transferase-encoding gene gpi7 was deleted and the resultant mutant characterized in terms of growth, development, and virulence. The Δgpi7 mutants exhibited slower radial growth rates and aberrantly shaped macroconidia. Furthermore, virulence tests and microscopic analyses indicated that Gpi7 is required for ramification of the fungus throughout the rachis of wheat heads. In parallel, bioinformatics tools were utilized to predict and inventory GPI-APs within the proteome of F. graminearum. Two of the genes identified in this screen (FGSG_01588 and FGSG_08844) displayed isolate-specific length variability as observed for other fungal cell wall adhesion genes. Nevertheless, deletion of these genes failed to reveal obvious defects in growth, development, or virulence. This research demonstrates the global importance of GPI-APs to in planta proliferation in F. graminearum, and also highlights the potential of individual GPI-APs as diagnostic markers. PMID:24312325

An approach to multi-attribute utility analysis under parametric uncertainty

International Nuclear Information System (INIS)

Kelly, M.; Thorne, M.C.

2001-01-01

The techniques of cost-benefit analysis and multi-attribute analysis provide a useful basis for informing decisions in situations where a number of potentially conflicting opinions or interests need to be considered, and where there are a number of possible decisions that could be adopted. When the input data to such decision-making processes are uniquely specified, cost-benefit analysis and multi-attribute utility analysis provide unambiguous guidance on the preferred decision option. However, when the data are not uniquely specified, application and interpretation of these techniques is more complex. Herein, an approach to multi-attribute utility analysis (and hence, as a special case, cost-benefit analysis) when input data are subject to parametric uncertainty is presented. The approach is based on the use of a Monte Carlo technique, and has recently been applied to options for the remediation of former uranium mining liabilities in a number of Central and Eastern European States

76 FR 10627 - Assumption Buster Workshop: Trust Anchors Are Invulnerable

Science.gov (United States)

2011-02-25

... day-long workshop on the pros and cons of the use and implementation of trust anchors. The workshop... National Coordination Office (NCO) for the Networking and Information Technology Research and Development... Coordination Office for the Networking and Information Technology Research and Development (NITRD) Program on...

Assembly and activation of alternative complement components on endothelial cell-anchored ultra-large von Willebrand factor links complement and hemostasis-thrombosis.

Directory of Open Access Journals (Sweden)

Nancy A Turner

Full Text Available Vascular endothelial cells (ECs express and release protein components of the complement pathways, as well as secreting and anchoring ultra-large von Willebrand factor (ULVWF multimers in long string-like structures that initiate platelet adhesion during hemostasis and thrombosis. The alternative complement pathway (AP is an important non-antibody-requiring host defense system. Thrombotic microangiopathies can be associated with defective regulation of the AP (atypical hemolytic-uremic syndrome or with inadequate cleavage by ADAMTS-13 of ULVWF multimeric strings secreted by/anchored to ECs (thrombotic thrombocytopenic purpura. Our goal was to determine if EC-anchored ULVWF strings caused the assembly and activation of AP components, thereby linking two essential defense mechanisms.We quantified gene expression of these complement components in cultured human umbilical vein endothelial cells (HUVECs by real-time PCR: C3 and C5; complement factor (CF B, CFD, CFP, CFH and CFI of the AP; and C4 of the classical and lectin (but not alternative complement pathways. We used fluorescent microscopy, monospecific antibodies against complement components, fluorescent secondary antibodies, and the analysis of >150 images to quantify the attachment of HUVEC-released complement proteins to ULVWF strings secreted by, and anchored to, the HUVECs (under conditions of ADAMTS-13 inhibition. We found that HUVEC-released C4 did not attach to ULVWF strings, ruling out activation of the classical and lectin pathways by the strings. In contrast, C3, FB, FD, FP and C5, FH and FI attached to ULVWF strings in quantitative patterns consistent with assembly of the AP components into active complexes. This was verified when non-functional FB blocked the formation of AP C3 convertase complexes (C3bBb on ULVWF strings.AP components are assembled and activated on EC-secreted/anchored ULVWF multimeric strings. Our findings provide one possible molecular mechanism for clinical

Meeting the Cool Neighbors. XII. An Optically Anchored Analysis of the Near-infrared Spectra of L Dwarfs

Science.gov (United States)

Cruz, Kelle L.; Núñez, Alejandro; Burgasser, Adam J.; Abrahams, Ellianna; Rice, Emily L.; Reid, I. Neill; Looper, Dagny

2018-01-01

Discrepancies between competing optical and near-infrared (NIR) spectral typing systems for L dwarfs have motivated us to search for a classification scheme that ties the optical and NIR schemes together, and addresses complexities in the spectral morphology. We use new and extant optical and NIR spectra to compile a sample of 171 L dwarfs, including 27 low-gravity β and γ objects, with spectral coverage from 0.6–2.4 μm. We present 155 new low-resolution NIR spectra and 19 new optical spectra. We utilize a method for analyzing NIR spectra that partially removes the broad-band spectral slope and reveals similarities in the absorption features between objects of the same optical spectral type. Using the optical spectra as an anchor, we generate near-infrared spectral average templates for L0–L8, L0–L4γ, and L0–L1β type dwarfs. These templates reveal that NIR spectral morphologies are correlated with the optical types. They also show the range of spectral morphologies spanned by each spectral type. We compare low-gravity and field-gravity templates to provide recommendations on the minimum required observations for credibly classifying low-gravity spectra using low-resolution NIR data. We use the templates to evaluate the existing NIR spectral standards and propose new ones where appropriate. Finally, we build on the work of Kirkpatrick et al. to provide a spectral typing method that is tied to the optical and can be used when only H or K band data are available. The methods we present here provide resolutions to several long-standing issues with classifying L dwarf spectra and could also be the foundation for a spectral classification scheme for cloudy exoplanets.

Anchoring group effects in molecular devices: An ab initio study on the electronic transport of a carbon-dimer

International Nuclear Information System (INIS)

Wang, R.N.; Zheng, X.H.; Dai, Z.X.; Hao, H.; Song, L.L.; Zeng, Z.

2011-01-01

The conductance of a molecular device is sensitive to the contact geometry between the molecules and the probing electrodes. Taking a carbon-dimer C 2 as an example and connecting it to the electrodes by different linking atoms H, Cu and S, we investigate the anchoring group effect in molecular devices by the first-principles approaches. The results exhibit that, depending on the anchoring groups and the subsequent different metal-molecule chemical bonds, the current varies over more than two orders of magnitude under the same bias. This emphasizes the great importance of the anchoring groups in molecular devices.

Dependence of optical phase modulation on anchoring strength of dielectric shield wall surfaces in small liquid crystal pixels

Science.gov (United States)

Isomae, Yoshitomo; Shibata, Yosei; Ishinabe, Takahiro; Fujikake, Hideo

2018-03-01

We demonstrated that the uniform phase modulation in a pixel can be realized by optimizing the anchoring strength on the walls and the wall width in the dielectric shield wall structure, which is the needed pixel structure for realizing a 1-µm-pitch optical phase modulator. The anchoring force degrades the uniformity of the phase modulation in ON-state pixels, but it also keeps liquid crystals from rotating against the leakage of an electric field. We clarified that the optimal wall width and anchoring strength are 250 nm and less than 10-4 J/m2, respectively.

A Comparative Study of McDonald’s Wedding Narratives with the Model of Anchoring

Directory of Open Access Journals (Sweden)

Mimi Huang

2016-12-01

Full Text Available Fast-food giant McDonald’s announced in 2010 that they would start hosting wedding ceremonies and receptions for couples who would like to get married in their restaurants in Hong Kong. This paper conducts a study comparing the differing representations of McDonald’s wedding services through a narrative analytical approach. Specifically, this paper examines relevant discourses surrounding the launch of the corporation’s wedding services from the British media (e.g. Daily Mail, the Independent as well as public discourses in Hong Kong (e.g. McDonald’s Hong Kong website, and CNN’s Hong Kong news.  It is found that these narratives have a significant degree of discrepancy in depicting McDonald’s wedding stories. These differences further raise the question of how differing narrative strategies are employed to conceptualise the brand’s emergent wedding narratives in a unique social-cultural environment.  In the discussion of McDonald’s wedding stories, the focus is placed on the cognitive and linguistic aspects of the discourse. An analytical model of “anchoring” will be proposed and applied to investigate the cooperation’s marketing strategies as well as the media’s reaction towards such promotions. It is argued that a narrative can promote or demote a brand’s identity and position through the process of anchoring. It is further argued that anchoring is an important cognitive-psychological strategy in conceptualization and meaning construction. Keywords: narrative inquiry, cognitive narratology, anchors, anchoring, meaning construction

A Multifaceted Study of Scedosporium boydii Cell Wall Changes during Germination and Identification of GPI-Anchored Proteins

Science.gov (United States)

Ghamrawi, Sarah; Gastebois, Amandine; Zykwinska, Agata; Vandeputte, Patrick; Marot, Agnès; Mabilleau, Guillaume; Cuenot, Stéphane; Bouchara, Jean-Philippe

2015-01-01

Scedosporium boydii is a pathogenic filamentous fungus that causes a wide range of human infections, notably respiratory infections in patients with cystic fibrosis. The development of new therapeutic strategies targeting S. boydii necessitates a better understanding of the physiology of this fungus and the identification of new molecular targets. In this work, we studied the conidium-to-germ tube transition using a variety of techniques including scanning and transmission electron microscopy, atomic force microscopy, two-phase partitioning, microelectrophoresis and cationized ferritin labeling, chemical force spectroscopy, lectin labeling, and nanoLC-MS/MS for cell wall GPI-anchored protein analysis. We demonstrated that the cell wall undergoes structural changes with germination accompanied with a lower hydrophobicity, electrostatic charge and binding capacity to cationized ferritin. Changes during germination also included a higher accessibility of some cell wall polysaccharides to lectins and less CH3/CH3 interactions (hydrophobic adhesion forces mainly due to glycoproteins). We also extracted and identified 20 GPI-anchored proteins from the cell wall of S. boydii, among which one was detected only in the conidial wall extract and 12 only in the mycelial wall extract. The identified sequences belonged to protein families involved in virulence in other fungi like Gelp/Gasp, Crhp, Bglp/Bgtp families and a superoxide dismutase. These results highlighted the cell wall remodeling during germination in S. boydii with the identification of a substantial number of cell wall GPI-anchored conidial or hyphal specific proteins, which provides a basis to investigate the role of these molecules in the host-pathogen interaction and fungal virulence. PMID:26038837

Supramolecule-Inspired Fabrication of Carbon Nanoparticles In Situ Anchored Graphene Nanosheets Material for High-Performance Supercapacitors.

Science.gov (United States)

Huang, Yulan; Gao, Aimei; Song, Xiaona; Shu, Dong; Yi, Fenyun; Zhong, Jie; Zeng, Ronghua; Zhao, Shixu; Meng, Tao

2016-10-12

The remarkable electrochemical performance of graphene-based materials has drawn a tremendous amount of attention for their application in supercapacitors. Inspired by supramolecular chemistry, the supramolecular hydrogel is prepared by linking β-cyclodextrin to graphene oxide (GO). The carbon nanoparticles-anchored graphene nanosheets are then assembled after the hydrothermal reduction and carbonization of the supramolecular hydrogels; here, the β-cyclodextrin is carbonized to carbon nanoparticles that are uniformly anchored on the graphene nanosheets. Transmission electron microscopy reveals that carbon nanoparticles with several nanometers are uniformly anchored on both sides of graphene nanosheets, and X-ray diffraction spectra demonstrate that the interlayer spacing of graphene is enlarged due to the anchored nanoparticles among the graphene nanosheets. The as-prepared carbon nanoparticles-anchored graphene nanosheets material (C/r-GO-1:3) possesses a high specific capacitance (310.8 F g -1 , 0.5 A g -1 ), superior rate capability (242.5 F g -1 , 10 A g -1 ), and excellent cycle stability (almost 100% after 10 000 cycles, at the scan rate of 50 mV s -1 ). The outstanding electrochemical performance of the resulting C/r-GO-1:3 is mainly attributed to (i) the presence of the carbon nanoparticles, (ii) the enlarged interlayer spacing of the graphene sheets, and (iii) the accelerated ion transport rates toward the interior of the electrode material. The supramolecule-inspired approach for the synthesis of high-performance carbon nanoparticles-modified graphene sheets material is promising for future application in graphene-based energy storage devices.

Effect of historical earthquakes on pre-stressed anchor tie back diaphragm wall and on near-by building

Directory of Open Access Journals (Sweden)

Kamal Mohamed Hafez Ismail Ibrahim

2013-04-01

Full Text Available Pre-stressed tie back anchored diaphragm walls are considered one of the safest lateral supports which help in overall stability when there is a significant difference in land level between back and front of these walls. Permanent lateral supports to these walls are frequently represented by supporting it laterally with foundation and floor slabs of the building. In this paper a special study of one raw anchor diaphragm wall subjected to different earthquake dynamic loads will be presented. The wall retains an excavation of 9.5 m and supports laterally a near-by 5 floor building. Five historical strong motions with different fundamental frequencies are subjected on the wall. The wall displacement, straining actions, anchor extreme force and the influence of variation of anchor stiffness are calculated using a dynamic Plaxis finite element program. The soil is considered as elasto-plastic material and represented using Mohr–Coulomb criteria, the wall and the anchor are considered to behave elastically. Prescribed displacement at the lower bottom boundary represents the earthquake motion. Far left and right absorbent boundaries are assumed to prevent dynamic wave reflection. Four static phases representing construction procedure and one dynamic loading phase are considered. It is found that the straining actions of different historical earthquakes match in shape with each other, the only change is in the amplitude which is affected by earthquake fundamental frequency and its intensity. The maximum dynamic lateral displacement of the wall is at its free top. The near-by building shows a differential settlement towards the wall which causes a change in the sign and amplitude of the straining actions. Increasing the stiffness of anchor was also studied and it was found that it reduces too much the maximum dynamic top wall lateral displacement.

Preparation and demonstration of poly(dopamine)-triggered attapulgite-anchored polyurethane as a high-performance rod-like elastomer to reinforce soy protein-isolated composites

Science.gov (United States)

Zhao, Shujun; Wen, Yingying; Wang, Zhong; Kang, Haijiao; Li, Jianzhang; Zhang, Shifeng; Ji, Yong

2018-06-01

Nanophase modification is an effective path to improve composite properties, however, it remains a great challenge to increase the mechanical strength of the modified materials without sacrificing elongation and toughness. This study presents a novel and efficient design for interface anchoring of a waterborne polyurethane (WPU) elastomer with attapulgite (ATP) triggered by poly(dopamine) (PDA) formation due to self-polymerization of the dopamine moieties. The WPU-PDA-ATP (WDA) rod-like elastomer served as an active enhancer for a soy protein isolate (SPI)-based composite to facilitate multiple interactions between SPI and the elastomer. As expected, the PDA layer was coated onto ATP, inducing the nanofiller to successfully anchor onto the WPU elastomer, as confirmed by solid-state 13C NMR, XPS, and ATR-FTIR results. Compared with the control SPI-based film, the tensile strength and toughness increased by 145.6% and 118.3% respectively by introducing WDA rod-like elastomer. The water resistance and thermal stability of the prepared SPI composites were also favorable. The proposed approach represents an efficient way to utilize high-performance elastomer in biobased materials to concurrently enhance strength and toughness.

Local ecological knowledge (LEK) on fish behavior around anchored FADs

NARCIS (Netherlands)

Macusi, Edison D.; Abreo, Neil A.S.; Babaran, Ricardo P.

2017-01-01

The Fishing Industry in the Philippines plays an important role in the food and employment need of Filipino fishers. By using anchored Fish Aggregating Devices (FADs or payao), the Philippine tuna fisheries was transformed into a million-dollar industry. Minimal studies on exploitation rates and

Stone anchors from Minicoy Island, Lakshadweep, India

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.

and Ali Rajas of Kerala. It appears that the mainland had contact with these islands during the early centuries of the Christian era, if not earlier (Sila Tripati, 1999). Though Islam came to Lakshadweep after the 11th and 12th centuries AD..., stitches, ropes and even sails (Hourani, 1995). With the passage of time the maritime contacts between the people of Lakshadweep and Arabs became closer, as demonstrated by the discovery of an Indo- 3 Arabian stone anchor in the Jama Mosque on Minicoy...

Anchoring device enabling relaxation of a multi-strand prestressing cable

International Nuclear Information System (INIS)

1979-01-01

Anchoring device, in a concrete structure, for a multi-strand prestressing cable, enabling the cable to be stressed or relaxed, comprising: (a) an axisymmetrical block, fitted with channels to enable the cable strands to be stressed and anchored through this block, (b) a duct with its opening splayed to a diameter greater than that of the block over a length corresponding to the stretching of the cable when being stressed, (c) a round bearing plate on the concrete around the expanded hole of the duct and (d) at least one intermediate removable bearing piece coming between the edge of the block and the internal edge of the plate. The removable parts are crown sectors of which the opposite bearing faces of each are slanted with respect to the centre line of the block and orientated in the same direction so as to transmit the cable stress at an angle from the block to the edge of the bearing plate [fr

Radiocarbon dates of the medieval period stone anchors from Dabhol, west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Gaur, A.S.; Sundaresh; Tripati, S.; Vora, K.H.

(Table 1) belong to Indo-Arab type and are similar to those reported from Dwarka, Bet Dwarka, Miyani, Visawada and Mithivirdi on the Saurash- tra coast 8 , and also on the Tamil Nadu coast 9 . Anchor 1 is with lower portion broad and tapers upper... the history of the place as a port/harbour. The anchors are similar to those reported from other places on the coast of India and the other Indian Ocean countries, including Dwarka 10 , Bet Dwarka 11 , Miyani and Visawada 12 , Somnath 13 and Mithivirdi...

Analysis and planning of the utilization of nuclear power plants

International Nuclear Information System (INIS)

Skvarka, P.

1985-01-01

The utilization coefficient as one of the characteristics of availability of nuclear power plants and the operation results (like maximum power, block number, and electric energy generation) are investigated by different statistic methods for several nuclear power plants with PWR type reactors and compared with those of WWER 440-type reactors. By means of linear many-parameter regression analysis the utilization coefficient is studied in dependence on block power and time after reactor commissioning. Forecastings of mean utilization coefficients are presented for the power of WWER 1000-type reactors

Metallurgical evaluation of failed post-tensioned containment tendon anchors at Joseph M. Farley Unit 2

International Nuclear Information System (INIS)

Czajkowski, C.J.

1986-01-01

A metallurgical examination has been performed on three failed post-tensioned containment tendon anchors and one intact anchor from the Farley Unit 2 Nuclear Power Station. The evaluation consisted of chemical/mechanical testing, optical microscopy, scanning electron microscopy, and energy dispersive spectroscopy. The conclusions drawn from the investigation were: 1) the anchors met the chemical and mechanical properties of AISI 4140/4142 steel; 2) there was no evidence of phosphorous segregation to the grain boundary (by ethereal picral etch); 3) the observed cracking was generally a mixed mode of intergranular and quasi-cleavage as well as ductile rupture with the intergranular cracking occurring along prior austenite grain boundaries; 4) the results of the mechanical tests coupled with the discontinuous nature of the intergranular areas and the elimination of other modes of failure give sufficient indication that the failure was a hydrogen induced cracking phenomenon

Hypomorphic mutations in PGAP2, encoding a GPI-anchor-remodeling protein, cause autosomal-recessive intellectual disability

DEFF Research Database (Denmark)

Hansen, Lars; Tawamie, Hasan; Murakami, Yoshiko

2013-01-01

PGAP2 encodes a protein involved in remodeling the glycosylphosphatidylinositol (GPI) anchor in the Golgi apparatus. After synthesis in the endoplasmic reticulum (ER), GPI anchors are transferred to the proteins and are remodeled while transported through the Golgi to the cell membrane. Germline...... mutations in six genes (PIGA, PIGL, PIGM, PIGV, PIGN, and PIGO) in the ER-located part of the GPI-anchor-biosynthesis pathway have been reported, and all are associated with phenotypes extending from malformation and lethality to severe intellectual disability, epilepsy, minor dysmorphisms, and elevated...... alkaline phosphatase (ALP). We performed autozygosity mapping and ultra-deep sequencing followed by stringent filtering and identified two homozygous PGAP2 alterations, p.Tyr99Cys and p.Arg177Pro, in seven offspring with nonspecific autosomal-recessive intellectual disability from two consanguineous...

The relation between career anchors, occupational types and job satisfaction of midcareer employees

Directory of Open Access Journals (Sweden)

J. A. Ellison

2000-06-01

Full Text Available The objective of this research was to determine the value of the career anchor model in career decision-making. Career models that can provide the individual with greater self-insight can serve as an important guide when making career choices in todays turbulent working environment. Two hundred and ninety-five midcareer employees (managerial and non-managerial completed questionnaires to determine their career anchor, occupation type and levels of general, intrinsic and extrinsic job satisfaction. The differences in job satisfaction between employees with a fit between career anchor and occupational type and those with no such fit were compared. It was found that respondents with a fit had a significantly higher level of general and intrinsic job satisfaction than those with no such fit. It is therefore suggested that the career anchor construct could probably serve as a useful tool for midcareer employees to make career choices. Opsomming Die doel van hierdie ondersoek was om die waarde van die loopbaanankermodel in loopbaanbesluitneming te bepaal. Loopbaanmodelle wat individue van groter insig kan voorsien kan as n belangrike riglyn in vandag se turbulente werksomgewing dien. Tweehonderd vyf-en-negentig middelloopbaan-werknemers (bestuur en nie-bestuur het vraelyste voltooi om hulle loopbaanankers, beroepstipe en vlakke van algemene, intrinsieke en ekstrinsieke werkstevredenheid te bepaal. Die verskille in werkstevredenheid tussen werknemers met n passing tussen loopbaananker en beroepstipe en die sender n sodanige passing, is vergelyk. Daar is bevind dat respondente met n passing 'n beduidende hoer vlak van algemene en intrinsieke werkstevredenheid het as die sender so 'n passing. Daar word derhalwe voorgestel dat die loopbaanankermodel waarskynlik as n nuttige instrument by middelloopbaan-werknemers gebruik kan word om loopbaanbesluite te neem.

Anchoring platinum on graphene using metallic adatoms: a first principles investigation

International Nuclear Information System (INIS)

Sen, F G; Alpas, A T; Qi, Y

2012-01-01

First principles calculations based on spin-polarized density functional theory were used to identify metallic adatoms that would strengthen the Pt(111)/graphene interface (with a low work of separation of 0.009 J m -2 ), when the adatom was placed between the Pt(111) and the graphene. It was shown that the strength of the Pt-adatom bond, which had a metallic character, increased with the amount of charge transferred from the adatom to the Pt. The carbon-adatom bond, on the other hand, had a mixed ionic and covalent character and was weaker than the Pt-adatom bond for each of the 25 elements considered. Consequently, the total Pt(111)/graphene interface strength and, hence, the anchoring effect of the adatom were controlled by the carbon-adatom bond strength. Metals with unfilled d orbitals increased the Pt/graphene interface strength to above 0.5 J m -2 . The carbon-adatom bond strength was proportional to the ratio between the charge transferred from the adatom to the graphene (ΔZ C ) and the charge transferred to the Pt surface (ΔZ Pt ); i.e., the ΔZ C /ΔZ Pt ratio defined the ability of an adatom to anchor Pt to graphene. For Ir, Os, Ru, Rh and Re, ΔZ C /ΔZ Pt > 1.0, making these elements the most effective adatoms for anchoring Pt to graphene. (paper)

Arthroscopic knotless anchor repair of triangular fibrocartilage in distal radius fracture.

Science.gov (United States)

García-Ruano, Á A; Najarro-Cid, F; Jiménez-Martín, A; Gómez de los Infantes-Troncoso, J G; Sicre-González, M

2015-01-01

Lesions of triangular fibrocartilage (TFC) are associated with distal radioulnar joint instability. Arthroscopic treatment of these lesions improves functional outcome of affected patients. The aim of the present work is to evaluate functional and occupational outcome of TCF repair using an arthroscopic knotless anchor device in patients with associated distal radius fracture. An observational, descriptive study was carried out between November 2011 and January 2014 including 21 patients with distal radius fracture and Palmer 1B lesions of TCF (Atzei class 2 and 3) that were treated by arthroscopic knotless anchor (PopLok® 2,8mm, ConMed, USA). Mean follow-up was 18 months. Functional (Mayo Wrist Score) and occupational outcome results were analyzed. Mean age of the group was 43.0±8.8 years, with 19% of the patients being female. There was an associated scapholunate lesion in 5 cases. Functional results reached a mean of 83.4±16.1 points onMayo Wrist Score. Mean sick-leave time was 153.16±48.5 days. Complete occupational reintegration was reached in 89.5% of cases. There were no postoperative complications. Arthroscopic knotless anchor repair of 1B TFC tears is a minimally invasive method of treatment that improves tension of fixation, avoiding subsequent loosen, in our experience, with few complications and good functional and occupational results. Copyright © 2014 SECOT. Published by Elsevier Espana. All rights reserved.

Analysis of Low-Temperature Utilization of Geothermal Resources

Energy Technology Data Exchange (ETDEWEB)

Anderson, Brian

2015-06-30

Full realization of the potential of what might be considered “low-grade” geothermal resources will require that we examine many more uses for the heat than traditional electricity generation. To demonstrate that geothermal energy truly has the potential to be a national energy source we will be designing, assessing, and evaluating innovative uses for geothermal-produced water such as hybrid biomass-geothermal cogeneration of electricity and district heating and efficiency improvements to the use of cellulosic biomass in addition to utilization of geothermal in district heating for community redevelopment projects. The objectives of this project were: 1) to perform a techno-economic analysis of the integration and utilization potential of low-temperature geothermal sources. Innovative uses of low-enthalpy geothermal water were designed and examined for their ability to offset fossil fuels and decrease CO2 emissions. 2) To perform process optimizations and economic analyses of processes that can utilize low-temperature geothermal fluids. These processes included electricity generation using biomass and district heating systems. 3) To scale up and generalize the results of three case study locations to develop a regionalized model of the utilization of low-temperature geothermal resources. A national-level, GIS-based, low-temperature geothermal resource supply model was developed and used to develop a series of national supply curves. We performed an in-depth analysis of the low-temperature geothermal resources that dominate the eastern half of the United States. The final products of this study include 17 publications, an updated version of the cost estimation software GEOPHIRES, and direct-use supply curves for low-temperature utilization of geothermal resources. The supply curves for direct use geothermal include utilization from known hydrothermal, undiscovered hydrothermal, and near-hydrothermal EGS resources and presented these results at the Stanford

The Effects of Variability and Risk in Selection Utility Analysis: An Empirical Comparison.

Science.gov (United States)

Rich, Joseph R.; Boudreau, John W.

1987-01-01

Investigated utility estimate variability for the selection utility of using the Programmer Aptitude Test to select computer programmers. Comparison of Monte Carlo results to other risk assessment approaches (sensitivity analysis, break-even analysis, algebraic derivation of the distribtion) suggests that distribution information provided by Monte…

Dynamic Rewiring of Promoter-Anchored Chromatin Loops during Adipocyte Differentiation

DEFF Research Database (Denmark)

Siersbæk, Rasmus; Madsen, Jesper Grud Skat; Javierre, Biola Maria

2017-01-01

-C to demonstrate a rapid reorganization of promoter-anchored chromatin loops within 4 hr after inducing differentiation of 3T3-L1 preadipocytes. The establishment of new promoter-enhancer loops is tightly coupled to activation of poised (histone H3 lysine 4 mono- and dimethylated) enhancers, as evidenced...

Activation of the CXCR3 chemokine receptor through anchoring of a small molecule chelator ligand between TM-III, -IV, and -VI

DEFF Research Database (Denmark)

Rosenkilde, Mette M; Andersen, Michael B; Nygaard, Rie

2006-01-01

modeling and molecular simulations combined with mutational analysis indicated that the metal ion site-anchored chelators act as agonists by establishing an aromatic-aromatic, second-site interaction with TyrVI:16 on the inner face of TM-VI. It is noteworthy that this interaction required......Seven transmembrane segment (7TM) receptors are activated through a common, still rather unclear molecular mechanism by a variety of chemical messengers ranging from monoamines to large proteins. By introducing a His residue at position III:05 in the CXCR3 receptor a metal ion site was built...... between the extracellular ends of transmembrane (TM) III and TM-IV to anchor aromatic chelators at a location corresponding to the presumed binding pocket for adrenergic receptor agonists. In this construct, free metal ions had no agonistic effect in accordance with the optimal geometry of the metal ion...

MAIL1 is essential for development of the primary root but not of anchor roots

OpenAIRE

Ühlken, Christine; Hoth, Stefan; Weingartner, Magdalena

2014-01-01

MAIN-LIKE1 (MAIL1) is a ubiquitously expressed nuclear protein, which has a crucial function during root development. We have recently described loss of function mutants for MAIL1, in which the organization and function of the primary root meristem is lost soon after germination. Moreover cell differentiation is impaired resulting in primary root growth arrest soon after emergence. Here we show that mail1 mutants form several anchor roots from the hypocotyl to root junction. These anchor root...

The biggest stone anchors (Indo-Arab type) from Mithi Virdi, Bhavnagar, west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Gaur, A.S.; Sundaresh; Kumar, B.

of Oceanography, Goa on the Saurashtra coast have been undertaken at Dwarka (Gaur et al. 2000), Bet Dwarka (Sundaresh et al. 2002) and Somnath {Gaur et al. 2002). The prospections *National Institute of Oceanography, Dona Paula, Goa **Devli, Talaza, Bhavnagar... of stone anchors at Dwarka, Bet Dwarka, Aramda (Gaur et al. 2003), Somnath (Gaur ef al. 2002), Vijayadurg (Sila ef al. 1998), Sindhudurg (Sila and Gaur 1997), Goa waters (Sila et al. 2003) and Tamilnadu coast (Athiyaman 2001). These anchors...

ANCHORING IN THE POLITICAL AND ECONOMIC MARKETING

Directory of Open Access Journals (Sweden)

Tatyana L. Shklyar

2015-01-01

Full Text Available The main purpose of marketing, both ineconomy and in politics is to attract themaximum number of customers or voters, maximizing customer satisfaction and ,ideally, improve the quality of life.The author, in various aspects, thetechnology of anchoring used in NLP, to attract customers and voters, both in the economy and in politics.In different examples demonstrate theoverall impact on the psychology of the consumer. Separating policy and the economy, marketers are missing something. The author proposes to look at how psychologicalanchors affect these two, at fi rst glance, different vector.

Strength of suture anchor versus transosseous tunnel in anatomic reconstruction of the ankle lateral ligaments: a biomechanical study.

Science.gov (United States)

Li, Hong-Yun; Hua, Ying-Hui; Wu, Zi-Ying; Chen, Bo; Chen, Shi-Yi

2013-11-01

The purpose of this study was to compare the biomechanical characteristics of fixation with 2-suture anchors versus transosseous tunnel fixation in anatomic reconstruction of the ankle lateral ligaments. Six matched pairs of human cadaveric ankles underwent anatomic lateral ankle reconstruction, and fixation of the graft on the talus was achieved with 2 suture anchors or a transosseous tunnel. Ankles for the transosseous tunnel group were chosen at random, with the paired contralateral ankles used for the 2-suture anchor group. Half of the peroneus brevis tendon was harvested as a graft. For each technique, one end of the tendon was secured to the original insertion point of the anterior talofibular ligament (ATFL) at the talus, whereas the other end was armed with 2 No. 5 nonabsorbable sutures (Ethicon, Somerville, NJ) and passed through the bone tunnel in the fibula. Biomechanical testing was performed by applying the force in line with the graft. Load to failure was determined at a displacement rate of 50 mm/min. The load-displacement curve, maximum load at failure (N), and stiffness (N/mm) were recorded and compared between the 2 techniques. There was no difference between constructs in the 2-suture anchor group and the transosseous tunnel group in terms of the ultimate load and stiffness (161.8 ± 47.6 N v 171.9 ± 76.0 N; P = .92; 4.59 ± 1.85 N/mm v 5.77 ± 1.98 N/mm; P = .35). Most constructs failed because of anchor pullout in the 2-suture anchor group (5 of 6) and fracture of the bony bridge in the transosseous tunnel group (6 of 6). The strength of fixation with suture anchors in anatomic reconstruction of the ankle lateral ligaments was equivalent to transosseous tunnel fixation as determined with biomechanical testing. However, this study did not prove that one is advantageous over the other. Both techniques showed excellent biomechanical results. Therefore, the 2-suture anchor fixation approach can be safely used in anatomic reconstruction of the

Test results on the dynamic testing of expansion type concrete anchors

International Nuclear Information System (INIS)

Barron, B.; Rice, R.; Stephen, R.M.

1974-12-01

Tests were performed to determine the structural response of commercially available expansion type anchors for the FFTF when subjected to dynamic loadings similar to machine vibrations and earthquakes. The specimens were subjected to tension, shear, and combined shear-tension loads

Robust conductance of dumbbell molecular junctions with fullerene anchoring groups

DEFF Research Database (Denmark)

Markussen, Troels; Settnes, Mikkel; Thygesen, Kristian Sommer

2011-01-01

The conductance of a molecular wire connected to metallic electrodes is known to be sensitive to the atomic structure of the molecule-metal contact. This contact is to a large extent determined by the anchoring group linking the molecular wire to the metal. It has been found experimentally that a...

The development of argon arc brazing with Cu-based filler for ITER thermal anchor attachment

International Nuclear Information System (INIS)

Sun Zhenchao; Li Pengyuan; Pan Chuanjie; Hou Binglin; Han Shilei; Pei Yinyin; Long Weimin

2012-01-01

Thermal anchor is the key component of ITER magnet supports to maintain the low temperature for the nor mal operation of superconducting coils. During the advanced research of ITER thermal anchor attachment, dozens of brazing filler and several kinds of brazing technique have been developed and investigated. The test result shows that Cu-based alloy have the preferable mechanical properties at both room temperature and liquid nitrogen temperatures (77 K) for high brazing temperature. And it has a good weldability to 316LN. The brazing temperature of Cu-based filler is over 1000℃, but heat input is relatively low for shallower heating depth of argon arc brazing. Lower heat input is good for the control of brazing deformation. It is no need to clean after brazing because for argon arc brazing there is no bra- zing flux used. Arc brazing with Cu-based filler was chosen as the principal method for the attachment of thermal anchor. (authors)

Anchor effects in decision making can be reduced by the interaction between goal monitoring and the level of the decision maker's executive functions.

Science.gov (United States)

Schiebener, Johannes; Wegmann, Elisa; Pawlikowski, Mirko; Brand, Matthias

2012-11-01

Models of decision making postulate that interactions between contextual conditions and characteristics of the decision maker determine decision-making performance. We tested this assumption by using a possible positive contextual influence (goals) and a possible negative contextual influence (anchor) in a risky decision-making task (Game of Dice Task, GDT). In this task, making advantageous choices is well known to be closely related to a specific decision maker variable: the individual level of executive functions. One hundred subjects played the GDT in one of four conditions: with self-set goal for final balance (n = 25), with presentation of an anchor (a fictitious Top 10 list, showing high gains of other participants; n = 25), with anchor and goal definition (n = 25), and with neither anchor nor goal setting (n = 25). Subjects in the conditions with anchor made more risky decisions irrespective of the negative feedback, but this anchor effect was influenced by goal monitoring and moderated by the level of the subjects' executive functions. The findings imply that impacts of situational influences on decision making as they frequently occur in real life depend upon the individual's cognitive abilities. Anchor effects can be overcome by subjects with good cognitive abilities.

An analysis of electric utility embedded power supply costs

International Nuclear Information System (INIS)

Kahal, M.; Brown, D.

1998-01-01

There is little doubt that for the vast majority of electric utilities the embedded costs of power supply exceed market prices, giving rise to the stranded cost problem. Beyond that simple generalization, there are a number of crucial questions, which this study attempts to answer. What are the regional patterns of embedded cost differences? To what extent is the cost problem attributable to nuclear power? How does the cost of purchased power compare to the cost of utility self-generation? What is the breakdown of utility embedded generation costs between operating costs - which are potentially avoidable--and ownership costs, which by definition are ''sunk'' and therefore not avoidable? How will embedded generation costs and market prices compare over time? These are the crucial questions for states as they address retail-restructuring proposal. This study presents an analysis of generation costs, which addresses these key questions. A computerized costing model was developed and applied using FERC Form 1 data for 1995. The model analyzed embedded power supply costs (i.e.; self-generation plus purchased power) for two groups of investor-owned utilities, 49 non-nuclear vs. 63 nuclear. These two subsamples represent substantially the entire US investor-owned electric utility industry. For each utility, embedded cost is estimated both at busbar and at meter

Material and welding development of anchor plates to build nuclear power plant by blue arc process

International Nuclear Information System (INIS)

Gibelli, C.E.

1986-01-01

To build nuclear power plants, anchor plates are plenty used. These anchor plates serve as a system with the purpose to fix many heavy components or a simple stair. Considering the necessity of element fabrication fastly, with reasonable economy and quality, the arc study welding process (blue arc) was used. A special development of the material concept as well as a welding procedure and a subsuppliers qualification of the raw material was necessary. (Author) [pt

Case-study application of venture analysis: the integrated energy utility. Volume 3. Appendices

Energy Technology Data Exchange (ETDEWEB)

Fein, E; Gordon, T J; King, R; Kropp, F G; Shuchman, H L; Stover, J; Hausz, W; Meyer, C

1978-11-01

The appendices for a case-study application of venture analysis for an integrated energy utility for commercialization are presented. The following are included and discussed: utility interviews; net social benefits - quantitative calculations; the financial analysis model; market penetration decision model; international district heating systems; political and regulatory environment; institutional impacts.

Drosophila acetylcholinesterase: demonstration of a glycoinositol phospholipid anchor and an endogenous proteolytic cleavage

International Nuclear Information System (INIS)

Haas, R.; Marshall, T.L.; Rosenberry, T.L.

1988-01-01

The presence of a glycoinositol phospholipid anchor Drosophila acetylcholinesterase (AChE) was shown by several criteria. Chemical analysis of highly purified Drosophila AChE demonstrated approximately one residue of inositol per enzyme subunit. Selective cleavage by Staphylococcus aureus phosphatidylinositol-specific phospholipase C (PI-PLC) was tested with Drosophila AChE radiolabeled by the photoactivatable affinity probe 3-(trifluoromethyl)-3-(m-[ 125 I]iodophenyl)diazirine ([ 125 I]TID), a reagent that specifically labels the lipid moiety of glycoinositol phospholipid-anchored proteins. Digestion with PI-PLC released 75% of this radiolabel from the protein. Gel electrophoresis of Drosophila AChE in sodium dodecyl sulfate indicated prominent 55- and 16-kDa bands and a faint 70-kDa band. The [ 125 ]I]TID label was localized on the 55-kDa fragment, suggesting that this fragment is the C-terminal portion of the protein. In support of this conclusion, a sensitive microsequencing procedure that involved manual Edman degradation combined with radiomethylation was used to determine residues 2-5 of the 16-kDa fragment. Comparison with the Drosophila AChE cDNA sequence confirmed that the 16-kDa fragment includes the N-terminus of AChE. Furthermore, the position of the N-terminal amino acid of the mature Drosophila AChE is closely homologous to that of Torpedo AChE. The presence of radiomethylatable ethanolamine in both 16- and 55-kDa fragments was also confirmed. Thus, Drosophila AChE may include a second posttranslational modification involving ethanolamine

The application of utility analysis processes to estimate the impact of training for nuclear maintenance personnel

International Nuclear Information System (INIS)

Groppel, C.F.

1991-01-01

The primary objectives of this study were to test two utility analysis models, the Cascio-Ramos Estimate of Performance in Dollars (CREPID) model and Godkewitsch financial utility analysis model and to determine their appropriateness as tools for evaluating training. This study was conducted in conjunction with Philadelphia Electric Company's Nuclear Training Group. Job performance of nuclear maintenance workers was assessed to document the impact of the training program. Assessment of job performance covered six job performance themes. Additionally, front-line nuclear maintenance supervisors were interviewed to determine their perceptions of the nuclear maintenance training. A comparison of supervisor's perceptions and outcomes of the utility analysis models was made to determine the appropriateness of utility analysis as quantitative tools for evaluating the nuclear maintenance training program. Application of the CREPID utility analysis model indicated the dollar value of the benefits of training through utility analysis was $5,843,750 which represented only four of the job performance themes. Application of the Godkewitsch utility analysis model indicated the dollar value of the benefits of training was $3,083,845 which represented all six performance themes. A comparison of the outcomes indicated a sizeable difference between the dollar values produced by the models. Supervisors indicated training resulted in improved productivity, i.e., improved efficiency and effectiveness. Additionally, supervisors believed training was valuable because it provided nonmonetary benefits, e.g., improved self-esteem and confidence. The application of utility analysis addressed only monetary benefits of training. The variation evidenced by the difference in the outcome of the two models suggests that utility analysis open-quotes estimatesclose quotes may not accurately reflect the impact of training

Bone-anchored maxillary expansion and bilateral interoral mandibular distraction osteogenesis in adult with severe obstructive sleep apnea syndrome.

Science.gov (United States)

Nie, Ping; Zhu, Min; Lu, Xiao-Feng; Fang, Bing

2013-05-01

Severe obstructive sleep apnea syndrome (OSAS) threatens patients' lives. To solve ventilation problem, snoring, and avoid another orthognathic surgery for mandibular advancement, bone-anchored rapid maxillary expansion and bilateral interoral mandibular distraction osteogenesis were tried on a 20-year-old Chinese male patient with severe skeletal class II malocclusion and OSAS.The patient had polysomnography (apnea-hypopnea index 54.2), body mass index measurement (19.7 kg/m), and cephalometry before the treatment. Bone-anchored rapid maxillary expansion was performed for the correction of maxillary transverse and minor sagittal deficiency and the improvement of nasal airflow by decreasing nasal resistance. Bilateral interoral mandibular distraction osteogenesis was operated to lengthen the small, retruded mandible by 15 mm. Orthodontic treatment after the maxillary expansion and mandibular distraction osteogenesis can help obtain stable occlusion.The Epworth Sleepiness Scale, a questionnaire for temporomandibular joint, cephalometric analysis, polysomnography, acoustic rhinometry, and multislice spiral computed tomography were performed to evaluate changes from the treatment. All the results showed that the patient had a significantly alleviated OSAS. In addition, an acceptable occlusion was also obtained.

78 FR 45104 - Model Manufactured Home Installation Standards: Ground Anchor Installations

Science.gov (United States)

2013-07-26

... anchor capacity. In granular soils, large lateral movements may produce failure planes that can reduce..., Consumer protection, Intergovernmental relations, Manufactured homes, Reporting and recordkeeping... relative to the plane of the ground surface and shall be permitted to be rounded to the nearest 5-degree...

Spatial Rearrangement and Mobility Heterogeneity of an Anionic Lipid Monolayer Induced by the Anchoring of Cationic Semiflexible Polymer Chains

Directory of Open Access Journals (Sweden)

Xiaozheng Duan

2016-06-01

Full Text Available We use Monte Carlo simulations to investigate the interactions between cationic semiflexible polymer chains and a model fluid lipid monolayer composed of charge-neutral phosphatidyl-choline (PC, tetravalent anionic phosphatidylinositol 4,5-bisphosphate (PIP2, and univalent anionic phosphatidylserine (PS lipids. In particular, we explore how chain rigidity and polymer concentration influence the spatial rearrangement and mobility heterogeneity of the monolayer under the conditions where the cationic polymers anchor on the monolayer. We find that the anchored cationic polymers only sequester the tetravalent PIP2 lipids at low polymer concentrations, where the interaction strength between the polymers and the monolayer exhibits a non-monotonic dependence on the degree of chain rigidity. Specifically, maximal anchoring occurs at low polymer concentrations, when the polymer chains have an intermediate degree of rigidity, for which the PIP2 clustering becomes most enhanced and the mobility of the polymer/PIP2 complexes becomes most reduced. On the other hand, at sufficiently high polymer concentrations, the anchoring strength decreases monotonically as the chains stiffen—a result that arises from the pronounced competitions among polymer chains. In this case, the flexible polymers can confine all PIP2 lipids and further sequester the univalent PS lipids, whereas the stiffer polymers tend to partially dissociate from the monolayer and only sequester smaller PIP2 clusters with greater mobilities. We further illustrate that the mobility gradient of the single PIP2 lipids in the sequestered clusters is sensitively modulated by the cooperative effects between anchored segments of the polymers with different rigidities. Our work thus demonstrates that the rigidity and concentration of anchored polymers are both important parameters for tuning the regulation of anionic lipids.

Analysis of influence of change of office hours on degree of heating of isolation of puttee of anchor of electric motor of piston compressor

Directory of Open Access Journals (Sweden)

A.V. Mazur

2012-12-01

Full Text Available The article is devoted the question of research of factors which influence on changing of the mode of operations of electric motor of compressor, which in same queue influence on the degree of heating of isolation of winding of anchor ED.

Analytical Model for Hook Anchor Pull-Out

DEFF Research Database (Denmark)

Brincker, Rune; Ulfkjær, Jens Peder; Adamsen, Peter

1995-01-01

A simple analytical model for the pull-out of a hook anchor is presented. The model is based on a simplified version of the fictitious crack model. It is assumed that the fracture process is the pull-off of a cone shaped concrete part, simplifying the problem by assuming pure rigid body motions...... allowing elastic deformations only in a layer between the pull-out cone and the concrete base. The derived model is in good agreement with experimental results, it predicts size effects and the model parameters found by calibration of the model on experimental data are in good agreement with what should...

Analytical Model for Hook Anchor Pull-out

DEFF Research Database (Denmark)

Brincker, Rune; Ulfkjær, J. P.; Adamsen, P.

A simple analytical model for the pull-out of a hook anchor is presented. The model is based on a simplified version of the fictitious crack model. It is assumed that the fracture process is the pull-off of a cone shaped concrete part, simplifying the problem by assuming pure rigid body motions...... allowing elastic deformations only in a layer between the pull-out cone and the concrete base. The derived model is in good agreement with experimental results, it predicts size effects and the model parameters found by calibration of the model on experimental data are in good agreement with what should...

Anchoring in Destination-Therapy Left Ventricular Assist Device Decision Making: A Mechanical Turk Survey.

Science.gov (United States)

Paine, Arcadia M; Allen, Larry A; Thompson, Jocelyn S; McIlvennan, Colleen K; Jenkins, Amy; Hammes, Andrew; Kroehl, Miranda; Matlock, Daniel D

2016-11-01

People with end-stage heart failure may have to decide about destination-therapy left ventricular assist device (DT-LVAD). Individuals facing difficult decisions often rely on heuristics, such as anchoring, which predictably bias decision outcomes. We aimed to investigate whether showing a larger historical Heartmate XVE creates an anchoring effect, making the smaller Heartmate II (HMII) appear more favorable. With the use of Amazon Mechanical Turk, participants watched videos asking them to imagine themselves dying of end-stage heart failure, then were presented the option of LVAD as potentially life-prolonging therapy. Participants were randomized to a control group who were only shown the HMII device, and the intervention group who saw the XVE device before the HMII. Participants then completed surveys. A total of 487 participants completed the survey (control = 252; intervention = 235); 79% were affect likelihood of accepting the LVAD, it did affect device perception. This article highlights an important point with clinical implications: factors such as anchoring have the potential to inappropriately influence perceptions and decisions and should be carefully considered in research and practice. Copyright © 2016 Elsevier Inc. All rights reserved.

Hydrophilic Cucurbit[7]uril-Pseudorotaxane-Anchored-Monolayer-Protected Gold Nanorods

Science.gov (United States)

2013-03-20

FULL PAPER DOI:10.1002/ejic.201300010 Hydrophilic Cucurbit[7]uril-Pseudorotaxane-Anchored- Monolayer-Protected Gold Nanorods Xiang Ma,[a] Yuhua Xue... Cao , Q. Wang, H. Tian, Chem. Commun. 2011, 47, 3559–3561. [8] a) I. Hwang, K. Baek, M. Jung, Y. Kim, K. M. Park, D. W. Lee, N. Selvapalam, K. Kim, J. Am

Memory for Dialogue: Recalling an Anchor through Talk and Response.

Science.gov (United States)

Beaver, Pam

This paper reports on a project involving student recall of the dialogue in a movie and retention of the "anchor," which in this case refers to a videotape recording of "To Kill a Mockingbird." The project looked at how students retained knowledge over a few days and what kind of activities resulted from expertise with an…

Binding equilibrium and kinetics of membrane-anchored receptors and ligands in cell adhesion: Insights from computational model systems and theory

Science.gov (United States)

Weikl, Thomas R.; Hu, Jinglei; Xu, Guang-Kui; Lipowsky, Reinhard

2016-01-01

ABSTRACT The adhesion of cell membranes is mediated by the binding of membrane-anchored receptor and ligand proteins. In this article, we review recent results from simulations and theory that lead to novel insights on how the binding equilibrium and kinetics of these proteins is affected by the membranes and by the membrane anchoring and molecular properties of the proteins. Simulations and theory both indicate that the binding equilibrium constant K2D and the on- and off-rate constants of anchored receptors and ligands in their 2-dimensional (2D) membrane environment strongly depend on the membrane roughness from thermally excited shape fluctuations on nanoscales. Recent theory corroborated by simulations provides a general relation between K2D and the binding constant K3D of soluble variants of the receptors and ligands that lack the membrane anchors and are free to diffuse in 3 dimensions (3D). PMID:27294442

Germ Plasm Anchoring Is a Dynamic State that Requires Persistent Trafficking

Directory of Open Access Journals (Sweden)

Kristina S. Sinsimer

2013-12-01

Full Text Available Localized cytoplasmic determinants packaged as ribonucleoprotein (RNP particles direct embryonic patterning and cell fate specification in a wide range of organisms. Once established, the asymmetric distributions of such RNP particles must be maintained, often over considerable developmental time. A striking example is the Drosophila germ plasm, which contains RNP particles whose localization to the posterior of the egg during oogenesis results in their asymmetric inheritance and segregation of germline from somatic fates in the embryo. Although actin-based anchoring mechanisms have been implicated, high-resolution live imaging revealed persistent trafficking of germ plasm RNP particles at the posterior cortex of the Drosophila oocyte. This motility relies on cortical microtubules, is mediated by kinesin and dynein motors, and requires coordination between the microtubule and actin cytoskeletons. Finally, we show that RNP particle motility is required for long-term germ plasm retention. We propose that anchoring is a dynamic state that renders asymmetries robust to developmental time and environmental perturbations.

Technical note: Endoscopic resection of a dermoid cyst anchored to the anterior optic chiasm

Directory of Open Access Journals (Sweden)

Yuichiro Yoneoka, MD, PhD

2014-06-01

Conclusion: To the best of our knowledge, ours is the only case of a dermoid cyst anchored to the anterior optic chiasma, which was visually confirmed under endoscopic observation. After surgery, the patient presented a transient impairment of the visual field, which was not evident at four month follow-up. It will contribute to a similar case, in which surgeons hesitate to make an incision in the optic chiasm. A subtotal excision should be considered in cases of dermoid cysts anchored to the anterior optic chiasm, because all the previously reported cases of suprasellar dermoid cysts are young people or those who have a relatively long life expectancy.

Avulsion Fracture of the Calcaneus Treated With a Soft Anchor Bridge and Lag Screw Technique: A Report of Two Cases.

Science.gov (United States)

Yoshida, Kazushige; Kasama, Kentaro; Akahane, Tsutomu

2016-01-01

The displaced extra-articular avulsion fracture of the calcaneus has been classified as a Böhler type 1c calcaneal fracture, and most cases will require surgical repair. In the present report, we describe 2 patients in whom we performed the soft anchor bridge technique using single loaded suture anchors with lag screws for the repair of Böhler type 1c avulsion fractures of the calcaneus. In one of these patients, clinically relevant osteoporosis complicated the injury. In both cases, bone union was achieved, and by 1.5 months after surgery satisfactory recovery was observed. To our knowledge, the soft anchor bridge technique was first used for the treatment of rotator cuff tears, and the greatest merit of this technique is the ability to generate vertical compression force to the pulled out rotator cuff through the use of knotting sutures. In recent years, the soft anchor bridge technique using 4 suture anchors has also been used for fractures of the greater tuberosity of the humerus, an injury that poses operative difficulties similar to those encountered with an avulsion fracture of the calcaneus owing to the traction force of the rotator cuff and relative weakness of adjacent bone. The outcomes of our patients suggest that the soft anchor bridge technique combined with adjunct lag screws is useful in the fixation of avulsion fractures of the calcaneus. In addition, the result in the elderly patient indicates the possibility of using this technique for patients with osteoporosis. Copyright © 2016 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

Proteomic analysis of human norepinephrine transporter complexes reveals associations with protein phosphatase 2A anchoring subunit and 14-3-3 proteins

International Nuclear Information System (INIS)

Sung, Uhna; Jennings, Jennifer L.; Link, Andrew J.; Blakely, Randy D.

2005-01-01

The norepinephrine transporter (NET) terminates noradrenergic signals by clearing released NE at synapses. NET regulation by receptors and intracellular signaling pathways is supported by a growing list of associated proteins including syntaxin1A, protein phosphatase 2A (PP2A) catalytic subunit (PP2A-C), PICK1, and Hic-5. In the present study, we sought evidence for additional partnerships by mass spectrometry-based analysis of proteins co-immunoprecipitated with human NET (hNET) stably expressed in a mouse noradrenergic neuroblastoma cell line. Our initial proteomic analyses reveal multiple peptides derived from hNET, peptides arising from the mouse PP2A anchoring subunit (PP2A-Ar) and peptides derived from 14-3-3 proteins. We verified physical association of NET with PP2A-Ar via co-immunoprecipitation studies using mouse vas deferens extracts and with 14-3-3 via a fusion pull-down approach, implicating specifically the hNET NH 2 -terminus for interactions. The transporter complexes described likely support mechanisms regulating transporter activity, localization, and trafficking

Bone-anchored hearing aids in conductive and mixed hearing losses: why do patients reject them?

Science.gov (United States)

Siau, Richard T K; Dhillon, Baljeet; Siau, Derrick; Green, Kevin M J

2016-10-01

This study aimed to report the bone-anchored hearing aid uptake rate and the reasons for their rejection by patients with conductive and mixed hearing losses. A retrospective review was performed of 113 consecutive patients with unilateral or bilateral conductive or mixed hearing loss referred to the Greater Manchester bone-anchored hearing aid (BAHA) programme between September 2008 and August 2011. 98 (86.7 %) patients were deemed audiologically suitable for BAHA implantation. Of these, 38 (38.8 %) had BAHA implanted; 60 (61.2 %) patients declined. Of those who declined, 27 (45 %) cited anxiety over surgery, 18 (30 %) cited cosmetic reasons, 16 (26.7 %) perceived limited benefit from the device and six (10 %) preferred conventional hearing aids. Our study highlights a 38.8 % BAHA uptake rate in audiologically suitable patients. The main reasons cited for rejection of BAHA were anxiety over surgery and cosmetic concerns. It is important that clinicians address these early during consultation with prospective BAHA recipients and avoid rushing to implant these patients with a bone-anchored hearing aid.

Work values and career anchors: the perspective of students of higher education in classroom methods and distance

Directory of Open Access Journals (Sweden)

Tais de Andrade

2018-01-01

Full Text Available This study takes into account the factors that interfere with career decisions from the internal demands of individuals, represented by the work values. Investigated university students’ perspective on work values and career anchors. For this, we used a survey along the 958 undergraduate students of face and distance higher education institutions in the interior of Rio Grande do Sul. The data collection instrument was developed from the Work Values Scale Revised developed by Porto and Pilati (2010 and the Inventory of Career Anchors proposed by Schein (1993; 1996. As for the results, there were significant differences between the perceptions of the two methods of teaching, but the hierarchy assigned to the values and anchors in both was similar, which shows certain pattern of agreement as to the perception of importance attached to each dimension studied.

The RIO approach : Design and anchoring of sustainable animal husbandry systems

NARCIS (Netherlands)

Elzen, Boelie; Bos, Bram

2016-01-01

This paper discusses an approach to develop new 'integrally sustainable' animal production systems and stimulate their uptake in practice. It consists of a design approach called RIO, and a set of 'anchoring' activities to stimulate their uptake in niches and in the regime. In the period 2001-2015

Structural Health Monitoring and Time-Dependent Effects Analysis of Self-Anchored Suspension Bridge with Extra-Wide Concrete Girder

Directory of Open Access Journals (Sweden)

Guangpan Zhou

2018-01-01

Full Text Available The present work is aimed at studying the structural health status of Hunan Road Bridge, which is currently the widest concrete self-anchored suspension bridge in China. The monitoring data included the structural deformations, internal forces, and vibration characteristics from April 2015 to April 2016 were analyzed to evaluate the structural changes and safety. The influences brought by the ambient temperature changes and the dual effects composed of concrete shrinkage & creep (S&C and seasonal temperature changes were analyzed based on the measured data. The long-time effects of concrete S&C were predicted using the CEB-FIP 90 model and the age-adjusted effective modulus method based on the ANSYS beam finite element model. The measured data showed that the transverse displacements of towers were more significant than the longitudinal ones. The spatial effect of the extra-wide girder is significant, which performs as the longitudinal stresses change unevenly along the transverse direction. The seasonal ambient warming caused overall increases in girder compressive stresses, and the cooling resulted in decreases along with significant temperature gradient effects. The prediction results show that the cable anchoring positions at girder ends and tower tops will move towards the mid-span affected by concrete S&C. In terms of the middle region of mid-span girder, significant increases in longitudinal stresses of top plate and decreases in the ones of bottom plate will be caused by the significant deflection. Comprehensively, the increases in the girder compressive stresses of side-span bottom plate and mid-span top plate are worthy of attention when confronted with extreme high temperature during the bridge service life cycle.

A prospective outcome and cost-effectiveness comparison between two ligament reattachment techniques using suture anchors for chronic ankle instability.

Science.gov (United States)

Cho, Byung-Ki; Kim, Yong-Min; Park, Kyoung-Jin; Park, Ji-Kang; Kim, Do-Kyoon

2015-02-01

There are various ligament reattachment techniques for the modified Brostrom procedure. There have been few comparative studies on recently developed techniques. This prospective study was performed to compare the functional outcomes of 2 different ligament reattachment techniques using suture anchors. We furthermore evaluated the cost-effectiveness of the suture bridge technique. Forty-five amateur athletes under 30 years of age were followed for more than 2 years. Twenty-four procedures with the suture anchor technique and 21 procedures with the suture bridge technique were performed by one surgeon. The functional evaluation consisted of the American Orthopaedic Foot & Ankle Society (AOFAS) score, Foot and Ankle Outcome Score (FAOS), Karlsson score, Sefton grading system, and the period to return to various forms of exercise (jogging, spurt running, jumping, one leg standing for >1 minute, walking on uneven ground, and going down stairs). Measurement of talar tilt angle and anterior talar translation was obtained from stress radiographs to evaluate mechanical stability. There were no significant differences on AOFAS score, FAOS, Karlsson score, Sefton grade, and stress radiographs. There were no significant differences on the return to exercises, except for jumping. As the most common complication, there were 3 cases of skin irritation by suture materials in the suture anchor group and 2 cases of intraoperative breakage of the suture anchor in suture bridge group. Both ligament reattachment techniques using suture anchors showed similar functional outcomes. Considering the additional medical expenses incurred by more suture anchors, the modified Brostrom procedure using the suture bridge technique had low cost-effectiveness. Proper indication and clinical usefulness of suture bridge technique for chronic ankle instability will be addressed in further studies. Level II, prospective comparative study. © The Author(s) 2014.

Fracture resistance of reattached incisor fragments with mini fibre-reinforced composite anchors.

NARCIS (Netherlands)

Fennis, W.M.M.; Kreulen, C.M.; Wolke, J.G.C.; Fokkinga, W.A.; Machado, C.; Creugers, N.H.J.

2009-01-01

OBJECTIVES: Fractured coronal fragments of incisors can be adhered to the remaining tooth with resin composite, but are prone to failure. This study explores whether mini fibre-reinforced composite (FRC) anchors increase fracture resistance of reattached fragments. METHODS: Forty-five extracted

Laparoscopic sacrocolpopexy with bone anchor fixation: short-term anatomic and functional results.

NARCIS (Netherlands)

Withagen, M.I.J.; Vierhout, M.E.; Mannaerts, G.H.; Weiden, R.M.F. van der

2012-01-01

INTRODUCTION AND HYPOTHESIS: The aim of this study was to evaluate short-term anatomic and functional outcomes and safety of laparoscopic sacrocolpopexy with bone anchor fixation. METHODS: A prospective cohort study of women undergoing laparoscopic sacrocolpopexy between 2004 and 2009. Anatomic

The Effect of Listener Experience and Anchors on Judgments of Dysphonia

Science.gov (United States)

Eadie, Tanya L.; Kapsner-Smith, Mara

2011-01-01

Purpose: To determine the effect of auditory anchors on judgments of overall severity (OS) and vocal effort (VE) in dysphonic speech when judgments are made by experienced and inexperienced listeners, and when self-rated by individuals with dysphonia (speaker-listeners). Method: Twenty individuals with dysphonia and 4 normal controls provided…

Sizing Analysis for Aircraft Utilizing Hybrid-Electric Propulsion Systems

Science.gov (United States)

2011-03-18

world, the paragon of animals -William Shakespeare I would not have made it this far without the love and support of my parents. Their work-ethic...xiii  I.  Introduction ...Condition 1 SIZING ANALYSIS FOR AIRCRAFT UTILIZING HYBRID- ELECTRIC PROPULSION SYSTEMS I. Introduction 1. Background Physically

Utilization of Multimedia Laboratory: An Acceptance Analysis using TAM

Science.gov (United States)

Modeong, M.; Palilingan, V. R.

2018-02-01

Multimedia is often utilized by teachers to present a learning materials. Learning that delivered by multimedia enables people to understand the information of up to 60% of the learning in general. To applying the creative learning to the classroom, multimedia presentation needs a laboratory as a space that provides multimedia needs. This study aims to reveal the level of student acceptance on the multimedia laboratories, by explaining the direct and indirect effect of internal support and technology infrastructure. Technology Acceptance Model (TAM) is used as the basis of measurement on this research, through the perception of usefulness, ease of use, and the intention, it’s recognized capable of predicting user acceptance about technology. This study used the quantitative method. The data analysis using path analysis that focuses on trimming models, it’s performed to improve the model of path analysis structure by removing exogenous variables that have insignificant path coefficients. The result stated that Internal Support and Technology Infrastructure are well mediated by TAM variables to measure the level of technology acceptance. The implications suggest that TAM can measure the success of multimedia laboratory utilization in Faculty of Engineering UNIMA.

Making a model meaningful to coral reef managers in a developing nation: a case study of overfishing and rock anchoring in Indonesia.

Science.gov (United States)

Maynard, Jeffrey A; Anthony, Kenneth R N; Afatta, Siham; Dahl-Tacconi, Nancy; Hoegh-Guldberg, Ove

2010-10-01

Most of the world's coral reefs line the coasts of developing nations, where impacts from intense and destructive fishing practices form critical conservation issues for managers. Overfishing of herbivorous fishes can cause phase shifts to macroalgal dominance, and fishers' use of rocks as anchors lowers coral cover, giving further competitive advantage to macroalgae. Overfishing and anchoring have been studied extensively, but the role of their interaction in lowering coral reef resilience has not been quantified formally. We analyzed the combined effects of overfishing and rock anchoring on a range of reef habitat types--varying from high coral and low macroalgae cover to low coral and high macroalgae cover--in a marine park in Indonesia. We parameterized a model of coral and algal dynamics with three intensities of anchoring and fishing pressure. Results of the model indicated that damage caused by rock anchoring was equal to or possibly more devastating to coral reefs in the area than the impact of overfishing. This is an important outcome for local managers, who usually have the funds to distribute less-damaging anchors, but normally are unable to patrol regularly and effectively enough to reduce the impact of overfishing. We translated model results into an interactive visual tool that allows managers to explore the benefits of reducing anchoring frequency and fishing pressure. The potential consequences of inaction were made clear: the likelihood that any of the reef habitats will be dominated in the future by macroalgae rather than corals depends on reducing anchoring frequency, fishing pressure, or both. The tool provides a platform for strengthened relationships between managers and conservationists and can facilitate the uptake of recommendations regarding resource allocation and management actions. Conservation efforts for coral reefs in developing nations are likely to benefit from transforming model projections of habitat condition into tools local

Electro-osmosis of nematic liquid crystals under weak anchoring and second-order surface effects

Science.gov (United States)

Poddar, Antarip; Dhar, Jayabrata; Chakraborty, Suman

2017-07-01

Advent of nematic liquid crystal flows has attracted renewed attention in view of microfluidic transport phenomena. Among various transport processes, electro-osmosis stands as one of the efficient flow actuation mechanisms through narrow confinements. In the present study, we explore the electrically actuated flow of an ordered nematic fluid with ionic inclusions, taking into account the influences from surface-induced elasticity and electrical double layer (EDL) phenomena. Toward this, we devise the coupled flow governing equations from fundamental free-energy analysis, considering the contributions from first- and second-order elastic, dielectric, flexoelectric, charged surface polarization, ionic and entropic energies. The present study focuses on the influence of surface charge and elasticity effects in the resulting linear electro-osmosis through a slit-type microchannel whose surfaces are chemically treated to display a homeotropic-type weak anchoring state. An optical periodic stripe configuration of the nematic director has been observed, especially for higher electric fields, wherein the Ericksen number for the dynamic study is restricted to the order of unity. Contrary to the isotropic electrolytes, the EDL potential in this case was found to be dependent on the external field strength. Through a systematic investigation, we brought out the fact that the wavelength of the oscillating patterns is dictated mainly by the external field, while the amplitude depends on most of the physical variables ranging from the anchoring strength and the flexoelectric coefficients to the surface charge density and electrical double layer thickness.

Stretching of a polymer chain anchored to a surface: the massive field theory approach

International Nuclear Information System (INIS)

Usatenko, Zoryana

2014-01-01

Taking into account the well-known correspondence between the field theoretical φ 4 O(n)-vector model in the limit n → 0 and the behaviour of long-flexible polymer chains, the investigation of stretching of an ideal and a real polymer chain with excluded volume interactions in a good solvent anchored to repulsive and inert surfaces is performed. The calculations of the average stretching force which arises when the free end of a polymer chain moves away from a repulsive or inert surface are performed up to one-loop order of the massive field theory approach in fixed space dimensions d = 3. The analysis of the obtained results indicates that the average stretching force for a real polymer chain anchored to a repulsive surface demonstrates different behaviour for the cases z-tilde ≪1 and z-tilde ≫1, where z-tilde =z ′ /R z . Besides, the results obtained in the framework of the massive field theory approach are in good agreement with previous theoretical results for an ideal polymer chain and results of a density functional theory approach for the region of small applied forces when deformation of a polymer chain in the direction of the applied force is not bigger than the linear extension of a polymer chain in this direction. The better agreement between these two methods is observed in the case where the number of monomers increases and the polymer chain becomes longer. (paper)

Thoracic aortic stent-graft placement combined with left subclavian artery 'chimney operation': therapeutic analysis of 15 cases with insufficient proximal anchor area

International Nuclear Information System (INIS)

Liu Jiayi; Huang Lianjun; Fan Zhanming; Zhang Zhaoqi

2012-01-01

Objective: To discuss the strategies for the management of insufficient proximal anchoring area during the performance of transluminal stent-graft placement (TSGP), and to evaluate the feasibility of intentional coverage of the left subclavian artery (LSA) together with left subclavian artery stent-graft placement by using 'chimney operation' technique. Methods: A total of 15 patients with thoracic aortic diseases complicated by insufficient proximal anchoring area, who were encountered in authors' hospital during the period from Dec. 2009 to April 2011, were enrolled in this study. The clinical data were retrospectively analyzed. The thoracic aortic diseases included aortic dissection (n=6), aortic pseudoaneurysm (n=1), aortic aneurysm (n=4) and penetrating ulcer (n=4). Of the 15 patients, the distance between the lesion and LSA anchoring site 15 mm in 2. TSGP was carried out. The ostium of LSA was intentionally and completely covered by thoracic aortic stent-graft and left subclavian artery stent-graft placement was subsequently performed. The patients were kept under observation for symptoms of cerebral and upper limb ischemia. The postoperative complications such as endoleak and the patency of LSA were assessed with angiography. Results: Thoracic aortic stent-graft placement was successfully carried out in all 15 patients. In addition, one 'chimney' stent was properly implanted in LSA in each patient. After the procedure, no complications of nervous system or severe ischemia of upper extremity occurred. Follow-up examinations performed between 5 days to 3 months after the treatment revealed that the aortic stent-graft remained in stable condition and no type Ⅰ endoleak occurred, meanwhile the blood flow in 'chimney' stent was unobstructed. Conclusion: Intentional LSA coverage with 'chimney operation' can expand the applicability of TSGP with high tolerability. It is especially useful for patients with left vertebral artery blood supply dominance or with

[PART-KESSLER TECHNIQUE WITH SUTURE ANCHOR IN REPAIR OF SPONTANEOUS Achilles TENDON RUPTURE].

Science.gov (United States)

Qi, Jie; Duan, Liang; Li, Weiwei; Wei, Wenbo

2016-02-01

To summarize the application and experience of repairing spontaneous Achilles tendon rupture by part-Kessler technique with suture anchor. Between January 2011 and December 2013, 31 patients with spontaneous Achilles tendon rupture were treated by part-Kessler technique with suture anchor. Of 31 cases, 23 were male and 8 were female, aged 16-53 years (mean, 38 years). The left side was involved in 15 cases and the right side in 16 cases. The causes of injury included sudden heel pain and walking weakness during sports in 22 cases; no surefooted down-stairs, slip, and carrying heavy loads in 9 cases. The distance from broken site to the calcaneus adhension of Achilles tendon was 3-6 cm (mean, 4.2 cm). The time from injury to operation was 7 hours to 4 days (mean, 36.8 hours). All incisions healed by first intention without nerve injury or adhering with skin. The patients were followed up 6-24 months (mean, 15 months). All patients could complete 25 times heel raising without difficulty at 6 months after operation. No Achilles tendon rupture occurred again during follow-up. At 6 months after operation, the range of motion of the ankle joint in dorsiflexion and plantar flexion showed no significant difference between normal and affected sides (t=0.648, P=0.525; t=0.524, P=0.605). The circumference of the affected leg was significantly smaller than that of normal leg at 6 months after operation (t=2.074, P=0.041), but no significant difference was found between affected and normal sides at 12 months after operation (t=0.905, P=0.426). The American Orthopedic Foot and Ankle Society (AOFAS) scores at 6, 12, 18, and 24 months after operation were significantly higher than preoperative score (P0.05). Repairing spontaneous Achilles tendon rupture by part-Kessler technique with suture anchor can supply strong strain and decrease the shear forces of suture. So part-Kessler technique with suture anchor is successful in repairing spontaneous Achilles tendon rupture.

Formation and properties of surface-anchored polymer assemblies with tunable physico-chemical characteristics

Science.gov (United States)

Wu, Tao

We describe two new methodologies leading to the formation of novel surface-anchored polymer assemblies on solid substrates. While the main goal is to understand the fundamentals pertaining to the preparation and properties of the surface-bound polymer assemblies (including neutral and chargeable polymers), several examples also are mentioned throughout the Thesis that point out to practical applications of such structures. The first method is based on generating assemblies comprising anchored polymers with a gradual variation of grafting densities on solid substrates. These structures are prepared by first covering the substrate with a molecular gradient of the polymerization initiator, followed by polymerization from these substrate-bound initiator centers ("grafting from"). We apply this technique to prepare grafting density gradients of poly(acryl amide) (PAAm) and poly(acrylic acid) (PAA) on silica-covered substrates. We show that using the grafting density gradient geometry, the characteristics of surface-anchored polymers in both the low grafting density ("mushroom") regime as well as the high grafting density ("brush") regime can be accessed conveniently on a single sample. We use a battery of experimental methods, including Fourier transform infrared spectroscopy (FTIR), Near-edge absorption fine structure spectroscopy (NEXAFS), contact angle, ellipsometry, to study the characteristics of the surface-bound polymer layers. We also probe the scaling laws of neutral polymer as a function of grafting density, and for weak polyelectrolyte, in addition to the grafting density, we study the affect of solution ionic strength and pH values. In the second novel method, which we coined as "mechanically assisted polymer assembly" (MAPA), we form surface anchored polymers by "grafting from" polymerization initiators deposited on elastic surfaces that have been previously extended uniaxially by a certain length increment, Deltax. Upon releasing the strain in the

Building Foundations for Nuclear Security Enterprise Analysis Utilizing Nuclear Weapon Data

Energy Technology Data Exchange (ETDEWEB)

Josserand, Terry Michael [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Nuclear Security Enterprise and Cost Analysis; Young, Leone [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Nuclear Security Enterprise and Cost Analysis; Chamberlin, Edwin Phillip [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Nuclear Security Enterprise and Cost Analysis

2017-09-01

The Nuclear Security Enterprise, managed by the National Nuclear Security Administration - a semiautonomous agency within the Department of Energy - has been associated with numerous assessments with respect to the estimating, management capabilities, and practices pertaining to nuclear weapon modernization efforts. This report identifies challenges in estimating and analyzing the Nuclear Security Enterprise through an analysis of analogous timeframe conditions utilizing two types of nuclear weapon data - (1) a measure of effort and (2) a function of time. The analysis of analogous timeframe conditions that utilizes only two types of nuclear weapon data yields four summary observations that estimators and analysts of the Nuclear Security Enterprise will find useful.

Starting point anchoring effects in choice experiments

DEFF Research Database (Denmark)

Ladenburg, Jacob; Olsen, Søren Bøye

of preferences in Choice Experiments resembles the Dichotomous Choice format, there is reason to suspect that Choice Experiments are equally vulnerable to anchoring bias. Employing different sets of price levels in a so-called Instruction Choice Set presented prior to the actual choice sets, the present study...... subjectivity in the present study is gender dependent, pointing towards, that female respondents are prone to be affected by the price levels employed. Male respondents, on the other hand, are not sensitive towards these prices levels. Overall, this implicates that female respondents, when employing a low......-priced Instruction Choice Set, tend to express lower willingness-to-pay than when higher prices are employed....

Codend selectivity in a commercial Danish anchor seine

DEFF Research Database (Denmark)

Noack, Thomas; Frandsen, Rikke; Krag, Ludvig Ahm

2017-01-01

Danish seining (or anchor seining) is a fishing technique that is gaining increasing attention because itis considered to be a fuel-efficient fishing method with low environmental impact. However, scientificdocumentation of the selectivity characteristics of Danish seines is lacking, and the gear....... The estimatedselectivity curve of dab indicated, contrary to cod and plaice, low retention of individuals below MLS.Confidence limits for larger length classes of cod and red gurnard were relatively wide. For plaice, theestimated selection factor, which is the length with 50% retention divided by mesh size...

Investigation of edge plasmas in the anchor cell region of GAMMA 10

International Nuclear Information System (INIS)

Islam, Khairul; Nakashima, Yousuke; Yatsu, Kiyoshi

2000-01-01

The first results of Langmuir probe measurements at the outer transition region of the anchor cell of GAMMA 10 are given. A probe current asymmetry in vertical direction is found in this region. It is also found that the asymmetry of probe current increases in outward direction and the direction of the asymmetry is independent on movable limiter position. A relation of the plasma asymmetry with the main magnetic field configuration is investigated. Plasma flow through the non-asymmetric magnetic field configuration region is thought to be the source of plasma asymmetry in this region, i.e., ∇B and curvature drifts are responsible for the asymmetry. Possibility of cold plasma formation in the anchor cell region is obtained during plug electron cyclotron resonance heating (ECRH) and can be explained with the desorption of particles due to the collision of the drifted out particles with the wall. (author)

Innovation in abutment-free bone-anchored hearing devices in children: Updated results and experience.

Science.gov (United States)

Baker, Shaun; Centric, Aaron; Chennupati, Sri Kiran

2015-10-01

Bone-anchored hearing devices are an accepted treatment option for hearing restoration in various types of hearing loss. Traditional devices have a percutaneous abutment for attachment of the sound processor that contributes to a high complication rate. Previously, our institution reported on the Sophono (Boulder, CO, USA) abutment-free system that produced similar audiologic results to devices with abutments. Recently, Cochlear Americas (Centennial, CO, USA) released an abutment-free bone-anchored hearing device, the BAHA Attract. In contrast to the Sophono implant, the BAHA Attract utilizes an osseointegrated implant. This study aims to demonstrate patient benefit abutment-free devices, compare the results of the two abutment-free devices, and examine complication rates. A retrospective chart review was conducted for the first eleven Sophono implanted patients and for the first six patients implanted with the BAHA Attract at our institution. Subsequently, we analyzed patient demographics, audiometric data, clinical course and outcomes. Average improvement for the BAHA Attract in pure-tone average (PTA) and speech reception threshold (SRT) was 41dB hearing level (dBHL) and 56dBHL, respectively. Considering all frequencies, the BAHA Attract mean improvement was 39dBHL (range 32-45dBHL). The Sophono average improvement in PTA and SRT was 38dBHL and 39dBHL, respectively. The mean improvement with Sophono for all frequencies was 34dBHL (range 24-43dBHL). Significant improvements in both pure-tone averages and speech reception threshold for both devices were achieved. In direct comparison of the two separate devices using the chi-square test, the PTA and SRT data between the two devices do not show a statistically significant difference (p-value 0.68 and 0.56, respectively). The complication rate for these abutment-free devices is lower than that of those featuring the transcutaneous abutment, although more studies are needed to further assess this potential advantage

Electromagnetic interference of bone-anchored hearing aids by cellular phones.