WorldWideScience

Sample records for upper deck means

  1. Analisis Keandalan Struktur Padeye Berdasarkan Konfigurasi Rigging pada Lifting Upper Deck Modul Modec dengan Pendekatan Dinamik

    Directory of Open Access Journals (Sweden)

    Iqbal Gayuh Raharjaning Mukti Sumarsono

    2017-01-01

    Full Text Available Di dalam perusahaan yang bergerak dalam bidang fabrikasi, lifting merupakan salah satu tahapan terpenting dalam membangun bangunan lepas pantai sehingga diperlukan perhitungan dan analisis tambahan untuk memperhatikan apakah struktur tersebut aman ataupun tidak. Sekenario lifting berdasarkan konfigurasi rigging dapat dibuat untuk menentukan rigging equipment yang tepat. Pada kasus ini, struktur yang di-lifting adalah struktur upper deck dari modul MODEC yang dikerjakan oleh PT. GPS Batam. Deck ini memiliki panjang sekitar 19,5 m dan lebar 9 m. Berat total struktur dengan equipment sebesar 55 ton. Konfigurasi rigging yang akan digunakan ada tiga, yaitu Model A (tanpa spreader bar, Model B (satu spreader bar, dan Model C (dua spreader bar. Dari ketiga konfigurasi tersebut akan diperoleh dimensi padeye yang berbeda- beda. Model A, Model B, dan Model C memiliki diameter hole padeye masing-masing sebesar 74 mm, 65 mm, dan 52 mm. Tegangan dan UC tertinggi sama- sama terjadi pada Model A sebesar 17625,99 psi dan untuk UC sebesar 0,52. Tetapi hal ini berbanding terbalik apabila ditinjau dari daerah lubang. Tegangan ataupun UC yang lebih tinggi jatuh pada Model C yang menggunakan dua spreader bar sebesar 13936,58 psi dan nilai UC sebesar 0,45. Tegangan yang terjadi di attachments maupun sekitar hole dijadikan variabel dalam mencari keandalan yang terjadi pada tiap padeye dengan metode Mean value first order second moment (MVFOSM. Sehingga didapatkan Probality of Failure (PoF pada attachments padeye pada Model A, B, dan C masing- masing sebesar 0,126%, 0,064 %, dan 0,0001 %. Sedangkan PoF pada hole padeye sebesar 0,062% untuk Model A, 0,10 % untuk Model B, dan 0,23% untuk Model C.

  2. Experimental evaluation of the buckling phenomena in the new joint design for upper deck structure of a bridge

    Directory of Open Access Journals (Sweden)

    Solazzi L.

    2010-06-01

    Full Text Available This paper is concerned with the experimental mechanical analysis of a new design of a joint for a main components of a upper deck of a road bridge. These components are subject to the compression state stress induced by the weight and the load acting on the road. Each upper deck of a bridge (positioned on each side of the bridge is composed by four tubular structures that must be joint each together. The joint must to take in to account many aspects, for example that the length of each component is not the same (because, obviously, there is a mechanical tolerance. This phenomena induce different compression stress on each component and so is very important non only the critical buckling load but also the post buckling behaviour of the structure. It is very important that if a single tubular structure reaches the critical load of instability, it still has load capacity . This is to avoid that, in the case where a column reaches the instability, the entire load acting on a column increase the load on the remaining three. For this purpose many different geometrical solutions have been designed (elaborated by fem analyses and successively tested experimentally. This work reports the main experimental results on the best joint solution and how this increase the load capacity and the displacement respect to the solution without this flange.

  3. Tracking upper limbs fatigue by means of electronic dynamometry

    Directory of Open Access Journals (Sweden)

    Fernando Max Lima

    2015-06-01

    Full Text Available This study aimed to identify useful electronic grip dynamometry parameters to track differences between trained (TR and untrained (UT participants, and between dominant (DO and non-dominant (ND limbs as a consequence of upper limbs muscle fatigue following 10 RM tests of the brachial biceps. This experimental study with transversal design involved 18 young adult males, of whom 9 were untrained and 9 were experienced in resistance training.Isometric grip force was evaluated (30 seconds long previous and after 10RM tests by means of a G200 Model grip dynamometer with precision load cell (Biometrics(r. Significant differences between initial and final measurements were found only for trained participants: Peak force for TR-DO (67.1 vs 55.5 kgf, p = .0277; Raw average for TR-DO (46.96 vs 42.22 kgf, p = .0464, and for TR-ND (40.34 vs 36.13 kgf, p = .0277. Electronic grip dynamometry efficiently identified upper limbs fatigue in trained participants, being raw average measurements the best parameter.

  4. STUDY OF BRIDGE DECK A REVIEW

    OpenAIRE

    MISS. KSHITIJA S. BALWAN , MR. V. G. KHURD , MR. S. S. CHOUGULE

    2018-01-01

    The objective of this study was to understand the meaning of bridge deck. To know the different forms of decks used in bridge design. To understand different methods used for analysis of deck and study of box girder and its evolution

  5. The upper atmosphere of Uranus - Mean temperature and temperature variations

    Science.gov (United States)

    Dunham, E.; Elliot, J. L.; Gierasch, P. J.

    1980-01-01

    The number-density, pressure, and temperature profiles of the Uranian atmosphere in the pressure interval from 0.3 to 30 dynes/sq cm are derived from observations of the occultation of SAO 158687 by Uranus on 1977 March 10, observations made from the Kuiper Airborne Observatory and the Cape Town station of the South African Astronomical Observatory. The mean temperature is found to be about 95 K, but peak-to-peak variations from 10 K to 20 K or more exist on a scale of 150 km or 3 scale heights. The existence of a thermal inversion is established, but the inversion is much weaker than the analogous inversion on Neptune. The mean temperature can be explained by solar heating in the 3.3 micron methane band with a methane mixing ratio of 4 x 10 to the -6th combined with the cooling effect of ethane with a mixing ratio of not greater than 4 x 10 to the -6th. The temperature variations are probably due to a photochemical process that has formed a Chapman layer.

  6. Optimizing rib width to height and rib spacing to deck plate thickness ratios in orthotropic decks

    Directory of Open Access Journals (Sweden)

    Abdullah Fettahoglu

    2016-12-01

    Full Text Available Orthotropic decks are composed of deck plate, ribs, and cross-beams and are frequently used in industry to span long distances, due to their light structures and load carrying capacities. Trapezoidal ribs are broadly preferred as longitudinal stiffeners in design of orthotropic decks. They supply the required stiffness to the orthotropic deck in traffic direction. Trapezoidal ribs are chosen in industrial applications because of their high torsional and buckling rigidity, less material and welding needs. Rib width, height, spacing, thickness of deck plate are important parameters for designing of orthotropic decks. In the scope of this study, rib width to height and rib spacing to deck plate thickness ratios are assessed by means of the stresses developed under different ratios of these parameters. For this purpose a FE-model of orthotropic bridge is generated, which encompasses the entire bridge geometry and conforms to recommendations given in Eurocode 3 Part 2. Afterwards necessary FE-analyses are performed to reveal the stresses developed under different rib width to height and rib spacing to deck plate thickness ratios. Based on the results obtained in this study, recommendations regarding these ratios are provided for orthotropic steel decks occupying trapezoidal ribs.

  7. Orthodontic decompensation in class III patients by means of distalization of upper molars.

    Science.gov (United States)

    Carlos, Villegas B; Giovanni, Oberti; Diego, Rey; Angela, Sierra; Baccetti, Tiziano

    2009-01-01

    Pre-surgical orthodontic treatments have the objective of establishing harmony between the dental arches by moving the teeth to ideal positions in relation to their bony bases, in order to achieve adequate antero-posterior occlusal and transverse relationships at the moment of surgery. Among the typical requirements in terms of dental compensations presented by Class III patients that require surgery, the inclination of anterior teeth must be changed in most cases by proclination of the lower incisors and retroclination of upper incisors. To achieve the inclination of the upper incisors, many different alternatives have been proposed, such as inter-proximal reduction, extractions, or distalization of upper molars, which has not been widely reported in the literature as a means to decompensate Class III malocclusion prior to surgery. This article describes the Bone Supported Pendulum (BSP) as an efficient therapeutic option to distalize molars through the use of an appliance stabilized to the palate by mini-implants, thus avoiding extractions and providing good interdigitation and coordination of the dental arches.

  8. Linear Cracking in Bridge Decks

    Science.gov (United States)

    2018-03-01

    Concrete cracking in bridge decks remains an important issue relative to deck durability. Cracks can allow increased penetration of chlorides, which can result in premature corrosion of the reinforcing steel and subsequent spalling of the concrete de...

  9. Exodermic bridge deck performance evaluation.

    Science.gov (United States)

    2010-07-01

    In 1998, the Wisconsin DOT completed a two"leaf bascule bridge in Green Bay with an exodermic deck system. The exodermic deck consisted of 4.5"in thick cast"in"place reinforced concrete supported by a 5.19"in tall unfilled steel grid. The concrete an...

  10. Classification of upper limb disability levels of children with spastic unilateral cerebral palsy using K-means algorithm.

    Science.gov (United States)

    Raouafi, Sana; Achiche, Sofiane; Begon, Mickael; Sarcher, Aurélie; Raison, Maxime

    2018-01-01

    Treatment for cerebral palsy depends upon the severity of the child's condition and requires knowledge about upper limb disability. The aim of this study was to develop a systematic quantitative classification method of the upper limb disability levels for children with spastic unilateral cerebral palsy based on upper limb movements and muscle activation. Thirteen children with spastic unilateral cerebral palsy and six typically developing children participated in this study. Patients were matched on age and manual ability classification system levels I to III. Twenty-three kinematic and electromyographic variables were collected from two tasks. Discriminative analysis and K-means clustering algorithm were applied using 23 kinematic and EMG variables of each participant. Among the 23 kinematic and electromyographic variables, only two variables containing the most relevant information for the prediction of the four levels of severity of spastic unilateral cerebral palsy, which are fixed by manual ability classification system, were identified by discriminant analysis: (1) the Falconer index (CAI E ) which represents the ratio of biceps to triceps brachii activity during extension and (2) the maximal angle extension (θ Extension,max ). A good correlation (Kendall Rank correlation coefficient = -0.53, p = 0.01) was found between levels fixed by manual ability classification system and the obtained classes. These findings suggest that the cost and effort needed to assess and characterize the disability level of a child can be further reduced.

  11. Skateboard deck materials selection

    Science.gov (United States)

    Liu, Haoyu; Coote, Tasha; Aiolos; Charlie

    2018-03-01

    The goal of this project was to identify the ideal material for a skateboard deck under 200 in price, minimizing the weight. The material must have a fracture toughness of 5 MPa/m2, have a minimum lifetime of 10, 000 cycles and must not experience brittle fracture. Both single material and hybrid solutions were explored. When further selecting to minimize weight, woods were found to be the best material. Titanium alloy-wood composites were explored to determine the optimal percentage composition of each material.A sandwich panel hybrid of 50% titanium alloy and 50% wood (Ti-Wood) was found to be the optimum material, performing better than the currently used plywood.

  12. Longer Lasting Bridge Deck Overlays

    Science.gov (United States)

    2018-04-01

    The objective of this report is to determine the most effective method for bridge deck overlay construction and repair by assessing current practices; examining new products and technologies; and reviewing NCHRP (National Cooperative Highway Research...

  13. Fiber reinforced polymer bridge decks.

    Science.gov (United States)

    2011-01-01

    The overarching goal of this study was to perform a comprehensive evaluation of various issues related to the strength and serviceability : of the FRP deck panels that are available in the industry. Specific objectives were to establish critical limi...

  14. Recognizing upper limb movements with wrist worn inertial sensors using k-means clustering classification.

    Science.gov (United States)

    Biswas, Dwaipayan; Cranny, Andy; Gupta, Nayaab; Maharatna, Koushik; Achner, Josy; Klemke, Jasmin; Jöbges, Michael; Ortmann, Steffen

    2015-04-01

    In this paper we present a methodology for recognizing three fundamental movements of the human forearm (extension, flexion and rotation) using pattern recognition applied to the data from a single wrist-worn, inertial sensor. We propose that this technique could be used as a clinical tool to assess rehabilitation progress in neurodegenerative pathologies such as stroke or cerebral palsy by tracking the number of times a patient performs specific arm movements (e.g. prescribed exercises) with their paretic arm throughout the day. We demonstrate this with healthy subjects and stroke patients in a simple proof of concept study in which these arm movements are detected during an archetypal activity of daily-living (ADL) - 'making-a-cup-of-tea'. Data is collected from a tri-axial accelerometer and a tri-axial gyroscope located proximal to the wrist. In a training phase, movements are initially performed in a controlled environment which are represented by a ranked set of 30 time-domain features. Using a sequential forward selection technique, for each set of feature combinations three clusters are formed using k-means clustering followed by 10 runs of 10-fold cross validation on the training data to determine the best feature combinations. For the testing phase, movements performed during the ADL are associated with each cluster label using a minimum distance classifier in a multi-dimensional feature space, comprised of the best ranked features, using Euclidean or Mahalanobis distance as the metric. Experiments were performed with four healthy subjects and four stroke survivors and our results show that the proposed methodology can detect the three movements performed during the ADL with an overall average accuracy of 88% using the accelerometer data and 83% using the gyroscope data across all healthy subjects and arm movement types. The average accuracy across all stroke survivors was 70% using accelerometer data and 66% using gyroscope data. We also use a Linear

  15. GARFEM input deck description

    Energy Technology Data Exchange (ETDEWEB)

    Zdunek, A.; Soederberg, M. (Aeronautical Research Inst. of Sweden, Bromma (Sweden))

    1989-01-01

    The input card deck for the finite element program GARFEM version 3.2 is described in this manual. The program includes, but is not limited to, capabilities to handle the following problems: * Linear bar and beam element structures, * Geometrically non-linear problems (bar and beam), both static and transient dynamic analysis, * Transient response dynamics from a catalog of time varying external forcing function types or input function tables, * Eigenvalue solution (modes and frequencies), * Multi point constraints (MPC) for the modelling of mechanisms and e.g. rigid links. The MPC definition is used only in the geometrically linearized sense, * Beams with disjunct shear axis and neutral axis, * Beams with rigid offset. An interface exist that connects GARFEM with the program GAROS. GAROS is a program for aeroelastic analysis of rotating structures. Since this interface was developed GARFEM now serves as a preprocessor program in place of NASTRAN which was formerly used. Documentation of the methods applied in GARFEM exists but is so far limited to the capacities in existence before the GAROS interface was developed.

  16. Quantifying reinforced concrete bridge deck deterioration using ground penetrating radar

    Science.gov (United States)

    Martino, Nicole Marie

    Bridge decks are deteriorating at an alarming rate due to corrosion of the reinforcing steel, requiring billions of dollars to repair and replace them. Furthermore, the techniques used to assess the decks don't provide enough quantitative information. In recent years, ground penetrating radar (GPR) has been used to quantify deterioration by comparing the rebar reflection amplitudes to technologies serving as ground truth, because there is not an available amplitude threshold to distinguish healthy from corroded areas using only GPR. The goal of this research is to understand the relationship between GPR and deck deterioration, and develop a model to determine deterioration quantities with GPR alone. The beginning of this research determines that not only is the relationship between GPR and rebar corrosion stronger than the relationship between GPR and delaminations, but that the two are exceptionally correlated (90.2% and 86.6%). Next, multiple bridge decks were assessed with GPR and half-cell potential (HCP). Statistical parameters like the mean and skewness were computed for the GPR amplitudes of each deck, and coupled with actual corrosion quantities based on the HCP measurements to form a future bridge deck model that can be used to assess any deck with GPR alone. Finally, in order to understand exactly which component of rebar corrosion (rust, cracking or chloride) attenuates the GPR data, computational modeling was carried out to isolate each variable. The results indicate that chloride is the major contributor to the rebar reflection attenuation, and that computational modeling can be used to accurately simulate GPR attenuation due to chloride.

  17. Fiber reinforced polymer bridge decks : [technical summary].

    Science.gov (United States)

    2011-01-01

    A number of researchers have addressed the use of Fiber Reinforced Polymer (FRP) deck as a replacement solution for deteriorated bridge decks made of traditional materials. The use of new, advanced materials such as FRP is advantageous when the bridg...

  18. Duality and the Deck effect

    CERN Document Server

    Törnqvist, N A

    1972-01-01

    As shown by Deck, the double-peripheral model for three-particle final states gives a substantial low-mass enhancement over phase space in two-body subchannels. With the advent of duality it was conjectured that the Deck effect and a true resonance are just different manifestations of the same phenomena. Thus the presence of a Deck enhancement could be interpreted as evidence for the existence of the A/sub 1/ resonance. The conjecture has been subject to criticism of two different kinds. These two points are clarified by constructing a counter example to the conjecture of Chew and Pignotti, using the five-point amplitude (B/sub 5/) of the generalized Veneziano model. (8 refs).

  19. 46 CFR 108.486 - Helicopter decks.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Helicopter decks. 108.486 Section 108.486 Shipping COAST... Fire Extinguishing Systems Fire Protection for Helicopter Facilities § 108.486 Helicopter decks. At least two of the accesses to the helicopter landing deck must each have a fire hydrant on the unit's...

  20. Steel plate reinforcement of orthotropic bridge decks

    NARCIS (Netherlands)

    Teixeira de Freitas, S.

    2012-01-01

    The PhD research is focused on the reinforcement of fatigue cracked orthotropic steel bridge decks (OBD) by adding a second steel plate to the existing deck. The main idea is to stiffen the existing deck plate, which will reduce the stresses at the fatigue sensitive details and extend the fatigue

  1. 75 FR 4584 - Wire Decking From China

    Science.gov (United States)

    2010-01-28

    ... Decking From China AGENCY: United States International Trade Commission. ACTION: Scheduling of the final... subsidized and less-than-fair-value imports from China of wire decking, provided for in subheadings 9403.90... China of wire decking, and that such [[Page 4585

  2. On the typography of flight-deck documentation

    Science.gov (United States)

    Degani, Asaf

    1992-01-01

    Many types of paper documentation are employed on the flight-deck. They range from a simple checklist card to a bulky Aircraft Flight Manual (AFM). Some of these documentations have typographical and graphical deficiencies; yet, many cockpit tasks such as conducting checklists, way-point entry, limitations and performance calculations, and many more, require the use of these documents. Moreover, during emergency and abnormal situations, the flight crews' effectiveness in combating the situation is highly dependent on such documentation; accessing and reading procedures has a significant impact on flight safety. Although flight-deck documentation are an important (and sometimes critical) form of display in the modern cockpit, there is a dearth of information on how to effectively design these displays. The object of this report is to provide a summary of the available literature regarding the design and typographical aspects of printed matter. The report attempts 'to bridge' the gap between basic research about typography, and the kind of information needed by designers of flight-deck documentation. The report focuses on typographical factors such as type-faces, character height, use of lower- and upper-case characters, line length, and spacing. Some graphical aspects such as layout, color coding, fonts, and character contrast are also discussed. In addition, several aspects of cockpit reading conditions such as glare, angular alignment, and paper quality are addressed. Finally, a list of recommendations for the graphical design of flight-deck documentation is provided.

  3. Meaning

    Science.gov (United States)

    Harteveld, Casper

    The second world to be considered concerns Meaning. In contrast to Reality and Play, this world relates to the people, disciplines, and domains that are focused on creating a certain value. For example, if this value is about providing students knowledge about physics, it involves teachers, the learning sciences, and the domains education and physics. This level goes into the aspects and criteria that designers need to take into account from this perspective. The first aspect seems obvious when we talk of “games with a serious purpose.” They have a purpose and this needs to be elaborated on, for example in terms of what “learning objectives” it attempts to achieve. The subsequent aspect is not about what is being pursued but how. To attain a value, designers have to think about a strategy that they employ. In my case this concerned looking at the learning paradigms that have come into existence in the past century and see what they have to tell us about learning. This way, their principles can be translated into a game environment. This translation involves making the strategy concrete. Or, in other words, operationalizing the plan. This is the third aspect. In this level, I will further specifically explain how I derived requirements from each of the learning paradigms, like reflection and exploration, and how they can possibly be related to games. The fourth and final aspect is the context in which the game is going to be used. It matters who uses the game and when, where, and how the game is going to be used. When designers have looked at these aspects, they have developed a “value proposal” and the worth of it may be judged by criteria, like motivation, relevance, and transfer. But before I get to this, I first go into how we human beings are meaning creators and what role assumptions, knowledge, and ambiguity have in this. I will illustrate this with some silly jokes about doctors and Mickey Mouse, and with an illusion.

  4. Missing data methods for dealing with missing items in quality of life questionnaires. A comparison by simulation of personal mean score, full information maximum likelihood, multiple imputation, and hot deck techniques applied to the SF-36 in the French 2003 decennial health survey.

    Science.gov (United States)

    Peyre, Hugo; Leplège, Alain; Coste, Joël

    2011-03-01

    Missing items are common in quality of life (QoL) questionnaires and present a challenge for research in this field. It remains unclear which of the various methods proposed to deal with missing data performs best in this context. We compared personal mean score, full information maximum likelihood, multiple imputation, and hot deck techniques using various realistic simulation scenarios of item missingness in QoL questionnaires constructed within the framework of classical test theory. Samples of 300 and 1,000 subjects were randomly drawn from the 2003 INSEE Decennial Health Survey (of 23,018 subjects representative of the French population and having completed the SF-36) and various patterns of missing data were generated according to three different item non-response rates (3, 6, and 9%) and three types of missing data (Little and Rubin's "missing completely at random," "missing at random," and "missing not at random"). The missing data methods were evaluated in terms of accuracy and precision for the analysis of one descriptive and one association parameter for three different scales of the SF-36. For all item non-response rates and types of missing data, multiple imputation and full information maximum likelihood appeared superior to the personal mean score and especially to hot deck in terms of accuracy and precision; however, the use of personal mean score was associated with insignificant bias (relative bias personal mean score appears nonetheless appropriate for dealing with items missing from completed SF-36 questionnaires in most situations of routine use. These results can reasonably be extended to other questionnaires constructed according to classical test theory.

  5. Reconstructing late quaternary fluvial process controls in the upper aller valley (north Germany) by means of numerical modeling

    NARCIS (Netherlands)

    Veldkamp, A.; Berg, van den M.; Dijke, van J.J.; Berg van Saparoea, van den R.M.

    2002-01-01

    The morpho-genetic evolution of the upper Aller valley (Weser basin, North Germany) was reconstructed using geological and geomorphologic data integrated within a numerical process model framework (FLUVER-2). The current relief was shaped by Pre-Elsterian fluvial processes, Elsterian and Saalian ice

  6. Reconstructing Late Quaternary fluvial process controls in the upper Aller Valley (North Germany) by means of numerical modeling

    NARCIS (Netherlands)

    Veldkamp, A.; Berg, M.W. van den; Dijke, J.J. van; Berg van den; Saparoea, R.M. van

    2002-01-01

    The morpho-genetic evolution of the upper Aller valley (Weser basin, North Germany) was reconstructed using geological and geomorphologic data integrated within a numerical process model framework (FLUVER-2). The current relief was shaped by Pre-Elsterian fluvial processes, Elsterian and Saalian ice

  7. A decking for erecting an insulating connector

    Energy Technology Data Exchange (ETDEWEB)

    Chuprikov, A Ye; Lagutin, V I; Sklyarov, A A; Sukhanov, G V

    1983-01-01

    The decking includes a parachute like dome, made of a material impenetrable to air, an air penetrable hood, attachment elements and a branch pipe for supplying the filler. To improve the sealing of the insulating connector upon contact with the walls and the roof of the drift being isolated and to reduce the labor intensity of operations, it is equipped with a housing made in the form of a cylinder from a material impenetrable to water, an advancible vertical upright and a spring loaded panel. The housing is installed between the parachute like dome and the air penetrable hood. The extendible vertical upright is installed on the side of the air penetrable hood and by means of a movable rack mechanism is kinematically linked with the spring loaded panel, installed with the capability of interacting with the air penetrable hood. The spring loaded plate is made in the form of perforated plates which have a telescopic disengagement in the horizontal plane.

  8. Usefulness of Interventional Treatment for Dysfunctional Hemodialysis Shunts of the Upper Arm by Means of the Retrograde Transradial Approach

    International Nuclear Information System (INIS)

    Shin, Hwa Seon; Shin, Tae Beom; Na, Jae Beom; Jung, Seong Hoon; Kim, Hyun Jung; Lee, Jung Eun; Song, Yun Gyu; Jung, Gyoo Sik

    2010-01-01

    This study was designed to evaluate the technical feasibility and clinical outcome of endovascular intervention using the retrograde transradial approach to treat dysfunctional hemodialysis shunts of the upper arms. During the last 3 years, sixteen procedures were performed by the transradial approach in 13 patients with dysfunctional hemodialysis shunts of the upper arms. The radial artery was accessed with the use of 20-gauge needle and a 6-Fr sheath. Angiography was performed using a 5-Fr catheter placed in the brachial artery, and then the interventional procedure was performed. The technical and clinical success rates, complications and patency rates were evaluated. Fistulography and percutaneous transluminal angioplasty via the transradial approach were performed in 16 cases of the 13 patients. Fistulography demonstrated stenosis in 7 cases and occlusions in 9 cases. Lesion multiplicity was identified in 9 out of 16 cases. Balloon angioplasty was performed in all cases and a stent was placed to overcome restenosis or to treat venous rupture in two cases. The technical success rate of balloon angioplasty was 87.5% (14/16) and the technical success rate with including stent insertion was 100% (16/16). The clinical success rate was 93.8%. There was one procedural-related complication. The primary patency rates at 6 and 12 months were 84.6% and 74%, respectively. The transradial approach seems to be technically feasible and effective for the management of insufficient hemodialysis shunts of the upper arms

  9. Experimental Investigation of Membrane Materials used in Multilayer Surfacing Systems for Orthotropic Steel Deck Bridges

    NARCIS (Netherlands)

    Tzimiris, G.

    2017-01-01

    In the Netherlands asphaltic surfacings on orthotropic steel deck bridges (OSDB) mostly consist of two structural layers. The upper layer consists of what is known as very open porous asphalt (ZOAB) for noise reduction. For the lower layer Guss Asphalt (GA) is used. Earlier investigations have shown

  10. Images from Galileo of the Venus cloud deck

    Science.gov (United States)

    Belton, M.J.S.; Gierasch, P.J.; Smith, M.D.; Helfenstein, P.; Schinder, P.J.; Pollack, James B.; Rages, K.A.; Ingersoll, A.P.; Klaasen, K.P.; Veverka, J.; Anger, C.D.; Carr, M.H.; Chapman, C.R.; Davies, M.E.; Fanale, F.P.; Greeley, R.; Greenberg, R.; Head, J. W.; Morrison, D.; Neukum, G.; Pilcher, C.B.

    1991-01-01

    Images of Venus taken at 418 (violet) and 986 [near-infrared (NIR)] nanometers show that the morphology and motions of large-scale features change with depth in the cloud deck. Poleward meridional velocities, seen in both spectral regions, are much reduced in the NIR. In the south polar region the markings in the two wavelength bands are strongly anticorrelated. The images follow the changing state of the upper cloud layer downwind of the subsolar point, and the zonal flow field shows a longitudinal periodicity that may be coupled to the formation of large-scale planetary waves. No optical lightning was detected.

  11. Hydrodynamic forces on inundated bridge decks

    Science.gov (United States)

    2009-05-01

    The hydrodynamic forces experienced by an inundated bridge deck have great importance in the design of bridges. Specifically, the drag force, lift force, and the moment acting on the bridge deck under various levels of inundation and a range of flow ...

  12. Robotics and Automation for Flight Deck Aircraft Servicing

    Energy Technology Data Exchange (ETDEWEB)

    Chesser, J.B.; Draper, J.V.; Pin, F.G.

    1999-03-01

    One of the missions of the Future Aircraft Carriers Program is to investigate methods that would improve aircraft turnaround servicing activities on carrier decks. The major objectives and criteria for evaluating alternative aircraft servicing methods are to reduce workload requirements, turnaround times (TAT), and life-cycle costs (LCC). Technologies in the field of Robotics and Automation (R and A) have the potential to significantly contribute to these objectives. The objective of this study was to investigate aircraft servicing functions on carrier decks which would offer the potentially most significant payoff if improved by various R and A technologies. Improvement in this case means reducing workload, time and LCC. This objective was accomplished using a ''bottom-up'' formalized approach as described in the following.

  13. Flight Deck I-Glasses, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Flight Deck i-Glasses is a color, stereoscopic 3-D display mounted on consumer style eye glass frames that will enhance operator performance and multi-modal...

  14. Deck41 Surficial Seafloor Sediment Description Database

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Deck41 is a digital summary of surficial sediment composition for 36,401 seafloor samples worldwide. Data include collecting source, ship, cruise, sample id,...

  15. Is deck B a disadvantageous deck in the Iowa Gambling Task?

    Directory of Open Access Journals (Sweden)

    Chiu Yao-Chu

    2007-03-01

    Full Text Available Abstract Background The Iowa gambling task is a popular test for examining monetary decision behavior under uncertainty. According to Dunn et al. review article, the difficult-to-explain phenomenon of "prominent deck B" was revealed, namely that normal decision makers prefer bad final-outcome deck B to good final-outcome decks C or D. This phenomenon was demonstrated especially clearly by Wilder et al. and Toplak et al. The "prominent deck B" phenomenon is inconsistent with the basic assumption in the IGT; however, most IGT-related studies utilized the "summation" of bad decks A and B when presenting their data, thereby avoiding the problems associated with deck B. Methods To verify the "prominent deck B" phenomenon, this study launched a two-stage simple version IGT, namely, an AACC and BBDD version, which possesses a balanced gain-loss structure between advantageous and disadvantageous decks and facilitates monitoring of participant preferences after the first 100 trials. Results The experimental results suggested that the "prominent deck B" phenomenon exists in the IGT. Moreover, participants cannot suppress their preference for deck B under the uncertain condition, even during the second stage of the game. Although this result is incongruent with the basic assumption in IGT, an increasing number of studies are finding similar results. The results of the AACC and BBDD versions can be congruent with the decision literatures in terms of gain-loss frequency. Conclusion Based on the experimental findings, participants can apply the "gain-stay, loss-shift" strategy to overcome situations involving uncertainty. This investigation found that the largest loss in the IGT did not inspire decision makers to avoid choosing bad deck B.

  16. Theoretical and Experimental Studies of Wave Impact underneath Decks of Offshore Platforms

    Energy Technology Data Exchange (ETDEWEB)

    Baarholm, Rolf Jarle

    2001-07-01

    The main objective of this thesis has been to study the phenomenon of water impact underneath the decks of offshore platforms due to propagating waves. The emphasis has been on the impact loads. Two theoretical methods based on two-dimensional potential theory have been developed, a Wagner based method (WBM) and a nonlinear boundary element method (BEM). A procedure to account for three-dimensional effects is suggested. The deck is assumed to be rigid. Initial studies of the importance of hydroelasticity for wave loads on an existing deck structure have been performed. For a given design wave, the local structural responses were found to behave quasi-static. Global structural response has not been studied. In the Wagner based method gravity is neglected and a linear spatial distribution of the relative impact velocity along the deck is assumed. The resulting boundary value problem is solved analytically for each time step. A numerical scheme for stepping the wetted deck area in time is presented. The nonlinear boundary element method includes gravity, and the exact impact velocity is considered. The incident wave velocity potential is given a priori, and a boundary value problem for the perturbation velocity potential associated with the impact is defined. The boundary value problem is solved for each time step by applying Green's second identity. The exact boundary conditions are imposed on the exact boundaries. A Kutta condition is introduced as the fluid flow reaches the downstream end of the deck. At present, the BEM is only applicable for fixed platform decks. To validate the theories, experiments have been carried out in a wave flume. The experiments were performed in two-dimensional flow condition with a fixed horizontal deck at different vertical levels above the mean free surface. The vertical force on the deck and the wetting of the deck were the primary parameters measured. Only regular propagating waves were applied. When a wave hits the deck, the

  17. Wave impact on a deck or baffle

    Science.gov (United States)

    Md Noar, Nor Aida Zuraimi; Greenhow, Martin

    2015-02-01

    Some coastal or ocean structures have deck-like baffles or horizontal platforms that can be exposed to wave action in heavy seas. A similar situation may occur in partially-filled tanks with horizontal baffles that become engulfed by sloshing waves. This can result in dangerous wave impact loads (slamming) causing a rapid rise of pressures which may lead to local damaging by crack initiation and/or propagation. We consider the wave impact against the whole of underside of horizontal deck (or baffle) projecting from a seawall (or vertical tank wall), previously studied by Wood and Peregrine (1996) using a different method based on conformal mappings. The approach used is to simplify the highly time-dependent and very nonlinear problem by considering the time integral of the pressure over the duration of the impact pressure-impulse, P (x, y). Our method expresses this in terms of eigenfunctions that satisfy the boundary conditions apart from that on the impact region and the matching of the two regions (under the platform and under the free surface); this results in a matrix equation to be solved numerically. As in Wood and Peregrine, we found that the pressure impulse on the deck increases when the length of deck increases, there is a strong pressure gradient beneath the deck near the seaward edge and the maximum pressure impulse occurs at the landward end of the impact zone.

  18. FGOALS-s2 simulation of upper-level jet streams over East Asia: Mean state bias and synoptic-scale transient eddy activity

    Science.gov (United States)

    Song, Fengfei; Zhou, Tianjun

    2013-05-01

    Upper-level jet streams over East Asia simulated by the LASG/IAP coupled climate system model FGOALS-s2 were assessed, and the mean state bias explained in terms of synoptic-scale transient eddy activity (STEA). The results showed that the spatial distribution of the seasonal mean jet stream was reproduced well by the model, except that following a weaker meridional temperature gradient (MTG), the intensity of the jet stream was weaker than in National Centers for Environment Prediction (NCEP)/Department of Energy Atmospheric Model Inter-comparison Project II reanalysis data (NCEP2). Based on daily mean data, the jet core number was counted to identify the geographical border between the East Asian Subtropical Jet (EASJ) and the East Asian Polar-front Jet (EAPJ). The border is located over the Tibetan Plateau according to NCEP2 data, but was not evident in FGOALS-s2 simulations. The seasonal cycles of the jet streams were found to be reasonably reproduced, except that they shifted northward relative to reanalysis data in boreal summer owing to the northward shift of negative MTGs. To identify the reasons for mean state bias, the dynamical and thermal forcings of STEA on mean flow were examined with a focus on boreal winter. The dynamical and thermal forcings were estimated by extended Eliassen-Palm flux ( E) and transient heat flux, respectively. The results showed that the failure to reproduce the tripolar-pattern of the divergence of E over the jet regions led to an unsuccessful separation of the EASJ and EAPJ, while dynamical forcing contributed less to the weaker EASJ. In contrast, the weaker transient heat flux partly explained the weaker EASJ over the ocean.

  19. Gust loading on streamlined bridge decks

    DEFF Research Database (Denmark)

    Larose, Guy; Mann, Jakob

    1998-01-01

    The current analytical description of the buffeting action of wind on long-span bridges is based on the strip assumption. However, recent experiments on closed-box girder bridge decks have shown that this assumption is not valid and is the source of an important part of the error margin...... of the analytical prediction methods. In this paper, an analytical model that departs from the strip assumption is used to describe the gust loading on a thin airfoil. A parallel is drawn between the analytical model and direct measurements of gust loading on motionless closed-box girder bridge decks. Empirical...

  20. 46 CFR 108.487 - Helicopter deck fueling operations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Helicopter deck fueling operations. 108.487 Section 108... DESIGN AND EQUIPMENT Fire Extinguishing Systems Fire Protection for Helicopter Facilities § 108.487 Helicopter deck fueling operations. (a) Each helicopter landing deck on which fueling operations are...

  1. 46 CFR 132.320 - Helicopter-landing decks.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Helicopter-landing decks. 132.320 Section 132.320 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS FIRE-PROTECTION EQUIPMENT Miscellaneous § 132.320 Helicopter-landing decks. Each vessel with a helicopter-landing deck must...

  2. 46 CFR 12.15-13 - Deck engine mechanic.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Deck engine mechanic. 12.15-13 Section 12.15-13 Shipping... ENDORSEMENTS Qualified Member of the Engine Department § 12.15-13 Deck engine mechanic. (a) An applicant for an endorsement as deck engine mechanic shall be a person holding an MMC or MMD endorsed as junior engineer. The...

  3. 46 CFR 174.215 - Drainage of weather deck.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Drainage of weather deck. 174.215 Section 174.215 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY SPECIAL RULES... weather deck. The weather deck must have open rails to allow rapid clearing of water, or must have freeing...

  4. 46 CFR 173.062 - Drainage of weather deck.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Drainage of weather deck. 173.062 Section 173.062 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY SPECIAL RULES PERTAINING TO VESSEL USE School Ships § 173.062 Drainage of weather deck. The weather deck of each sailing...

  5. Cone calorimeter tests of wood-based decking materials

    Science.gov (United States)

    Robert H. White; Mark A. Dietenberger; Nicole M. Stark

    2007-01-01

    New technologies in building materials have resulted in the use of a wide variety of materials in decks. As part of our effort to address fire concerns in the wildland-urban interface, the Forest Products Laboratory has been examining the fire performance of decking products. In addition to preservative-treated wood, decking products include wood-plastic composites and...

  6. Renovation techniques for fatigue cracked orthotropic steel bridge decks

    NARCIS (Netherlands)

    de Jong, F.B.P.

    2007-01-01

    This dissertation presents the research into renovation techniques for orthotropic steel bridge decks. These techniques are needed to solve fatigue problems in the decks of these bridges, as several fatigue cracks have been detected in the deck structure of these bridges the last decade. A

  7. Life-cycle assessment of redwood decking in the United States with a comparison to three other decking materials

    Science.gov (United States)

    R. Bergman; H. Sup-Han; E. Oneil; I. Eastin

    2013-01-01

    The goal of the study was to conduct a life-cycle inventory (LCI) of California redwood (Sequoia sempervirens) decking that would quantify the critical environmental impacts of decking from cradle to grave. Using that LCI data, a life-cycle assessment (LCA) was produced for redwood decking. The results were used to compare the environmental footprint...

  8. Deck Yourself with Flu Protection Song

    Centers for Disease Control (CDC) Podcasts

    2009-12-22

    This song (sung to the tune of Deck the Halls) describes actions you can take to protect yourself and others from the flu. Sing along!  Created: 12/22/2009 by National Center for Preparedness, Detection, and Control of Infectious Diseases (NCPDCID), Division of Global Migration and Quarantine (DGMQ).   Date Released: 12/22/2009.

  9. Analysis of Biaxially Stressed Bridge Deck Plates

    DEFF Research Database (Denmark)

    Jönsson, Jeppe; Bondum, Tommi Højer

    2012-01-01

    The ultimate state analysis of bridge deck plates at the intersection zone between main girders and transverse beams is complicated by biaxial membrane stresses, which may be in compression or tension in either direction depending on the bridge configuration and the specific location. This paper...

  10. Noise from Aft Deck Exhaust Nozzles: Differences in Experimental Embodiments

    Science.gov (United States)

    Bridges, James E.

    2014-01-01

    Two embodiments of a rectangular nozzle on an aft deck are compared. In one embodiment the lower lip of the nozzle was extended with the sidewalls becoming triangles. In a second embodiment a rectangular nozzle was fitted with a surface that fit flush to the lower lip and extended outward from the sides of the nozzle, approximating a semi-infinite plane. For the purpose of scale-model testing, making the aft deck an integral part of the nozzle is possible for relatively short deck lengths, but a separate plate model is more flexible, accounts for the expanse of deck to the sides of the nozzle, and allows the nozzle to stand off from the deck. Both embodiments were tested and acoustic far-field results were compared. In both embodiments the extended deck introduces a new noise source, but the amplitude of the new source was dependent upon the span (cross-stream dimension) of the aft deck. The noise increased with deck length (streamwise dimension), and in the case of the beveled nozzle it increased with increasing aspect ratio. In previous studies of slot jets in wings it was noted that the increased noise from the extended aft deck appears as a dipole at the aft deck trailing edge, an acoustic source type with different dependence on velocity than jet mixing noise. The extraneous noise produced by the aft deck in the present studies also shows this behavior both in directivity and in velocity scaling.

  11. EOF analysis of COSMIC observations on the global zonal mean temperature structure of the Upper Troposphere and Lower Stratosphere from 2007 to 2013

    Science.gov (United States)

    Salinas, Cornelius Csar Jude H.; Chang, Loren C.

    2018-06-01

    This work presents the results of a Conventional Empirical Orthogonal Function Analysis on daily global zonal mean temperature profiles in the Upper Troposphere and Lower Stratosphere (15-35 km), as measured by the FORMOSAT-3/COSMIC mission from January 2007 to June 2013. For validation, results were compared with ERA-Interim reanalysis. Results show that, the leading global EOF mode (27%) from COSMIC is consistent with temperature anomalies due to the tropical cooling associated with boreal winter Sudden Stratospheric Warmings (SSW). The second global EOF mode from COSMIC (15.3%) is consistent with temperature anomalies due to the Quasi-biennial Oscillation (QBO). The third global mode from COSMIC (10.9%) is consistent with temperature anomalies due to the El Nino Southern Oscillation. This work also shows that the second northern hemisphere EOF mode from COSMIC (16.8%) is consistent with temperature anomalies due Rossby-wave breaking (RWB) which is expected to only be resolved by a high vertical and temporal resolution dataset like COSMIC. Our work concludes that the use of a high vertical and temporal resolution dataset like COSMIC yields non-seasonal EOF modes that are consistent with relatively more intricate temperature anomalies due to the SSW, QBO, ENSO and RWB.

  12. Characterization of mean transit time at large springs in the Upper Colorado River Basin, USA: A tool for assessing groundwater discharge vulnerability

    Science.gov (United States)

    Solder, John; Stolp, Bernard J.; Heilweil, Victor M.; Susong, David D.

    2016-01-01

    Environmental tracers (noble gases, tritium, industrial gases, stable isotopes, and radio-carbon) and hydrogeology were interpreted to determine groundwater transit-time distribution and calculate mean transit time (MTT) with lumped parameter modeling at 19 large springs distributed throughout the Upper Colorado River Basin (UCRB), USA. The predictive value of the MTT to evaluate the pattern and timing of groundwater response to hydraulic stress (i.e., vulnerability) is examined by a statistical analysis of MTT, historical spring discharge records, and the Palmer Hydrological Drought Index. MTTs of the springs range from 10 to 15,000 years and 90 % of the cumulative discharge-weighted travel-time distribution falls within the range of 2−10,000 years. Historical variability in discharge was assessed as the ratio of 10–90 % flow-exceedance (R 10/90%) and ranged from 2.8 to 1.1 for select springs with available discharge data. The lag-time (i.e., delay in discharge response to drought conditions) was determined by cross-correlation analysis and ranged from 0.5 to 6 years for the same select springs. Springs with shorter MTTs (<80 years) statistically correlate with larger discharge variations and faster responses to drought, indicating MTT can be used for estimating the relative magnitude and timing of groundwater response. Results indicate that groundwater discharge to streams in the UCRB will likely respond on the order of years to climate variation and increasing groundwater withdrawals.

  13. Organic Functional Group Playing Card Deck

    Science.gov (United States)

    Welsh, Michael J.

    2003-04-01

    The recognition and identification of organic functional groups, while essential for chemistry and biology majors, is also very useful for non-science majors in the study of molecules in art and life. In order to make this task more palatable for the non-science major (art and communications students), the images of a traditional playing deck of cards (heart, spade, diamond, and club) have been replaced with four representations of common organic functional groups. The hierarchy rules for naming two groups in a molecule is loosely incorporated to represent the sequence (King, Queen, Jack, ?, Ace) of the deck. Students practice recognizing and identifying organic groups by playing simple card games of "Old Maid" and "Go Fish". To play games like "Poker" or "Gin", a student must not only recognize the functional groups, but also master a naming hierarchy for the organic groups.

  14. Improvement of fatigue properties of orthotropic decks

    Czech Academy of Sciences Publication Activity Database

    Frýba, Ladislav; Urushadze, Shota

    2011-01-01

    Roč. 33, č. 4 (2011), s. 1166-1169 ISSN 0141-0296 R&D Projects: GA ČR GA103/08/1340; GA MŠk(CZ) 7E08098 Grant - others:BRIFAG -Bridge Fatigue Guidance(XE) RFSR_CT-2008-00033 Institutional research plan: CEZ:AV0Z20710524 Keywords : orthotropic deck * fatigue * prolonged life Subject RIV: JM - Building Engineering Impact factor: 1.351, year: 2011

  15. Evaluation of upper and lower bounds to energy eigenvalues in Shoenberg's perturbation-theory ground state by means of partitioning technique

    International Nuclear Information System (INIS)

    Logrado, P.G.; Vianna, J.D.M.

    Upper and lower bounds for the energy eigenvalues is Schoenberg's perturbation-theory ground state are studied. After a review of the characteristic features of the partitioning techniques the perturbative expansion proposed by Schoenberg is generated from an exact operator equation. The upper and lower bounds for the ground state eigenvalue are derived by using reaction and wave operators concepts, the bracketing function and operator inequalities. (Author) [pt

  16. Optimization of wood plastic composite decks

    Science.gov (United States)

    Ravivarman, S.; Venkatesh, G. S.; Karmarkar, A.; Shivkumar N., D.; Abhilash R., M.

    2018-04-01

    Wood Plastic Composite (WPC) is a new class of natural fibre based composite material that contains plastic matrix reinforced with wood fibres or wood flour. In the present work, Wood Plastic Composite was prepared with 70-wt% of wood flour reinforced in polypropylene matrix. Mechanical characterization of the composite was done by carrying out laboratory tests such as tensile test and flexural test as per the American Society for Testing and Materials (ASTM) standards. Computer Aided Design (CAD) model of the laboratory test specimen (tensile test) was created and explicit finite element analysis was carried out on the finite element model in non-linear Explicit FE code LS - DYNA. The piecewise linear plasticity (MAT 24) material model was identified as a suitable model in LS-DYNA material library, describing the material behavior of the developed composite. The composite structures for decking application in construction industry were then optimized for cross sectional area and distance between two successive supports (span length) by carrying out various numerical experiments in LS-DYNA. The optimized WPC deck (Elliptical channel-2 E10) has 45% reduced weight than the baseline model (solid cross-section) considered in this study with the load carrying capacity meeting acceptance criterion (allowable deflection & stress) for outdoor decking application.

  17. 46 CFR 28.565 - Water on deck.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Water on deck. 28.565 Section 28.565 Shipping COAST... VESSELS Stability § 28.565 Water on deck. (a) Each vessel with bulwarks must comply with the requirements... energy, “b” in Figure 28.565, must not be less than the water on deck heeling energy, “a” in Figure 28...

  18. Structural improvement of strengthened deck panels with externally bonded plates

    International Nuclear Information System (INIS)

    Sim, Jongsung; Oh, Hongseob

    2005-01-01

    Concrete bridge decks require eventual replacement and rehabilitation due to decreasing load-carrying capacity. This paper compares different strengthening design procedures that improve the usability and structural performance of bridge decks. The failure characteristics of bridge decks strengthened with various materials such as carbon fiber sheet, glass fiber sheet, steel plate, and grid CFRP and GFRP are analyzed, and the theoretical load-carrying capacities are evaluated using traditional beam and yield line theory, and punching shear analysis. The strengthening materials increase the punching shear strength of the deck and change the failure mode of the strengthened panel

  19. Profiled Deck Composite Slab Strength Verification: A Review

    Directory of Open Access Journals (Sweden)

    K. Mohammed

    2017-12-01

    Full Text Available The purpose of this article is to present an overview on alternate profiled deck composite slab (PDCS strength verification devoid of the expensive and complex laboratory procedures in establishing its longitudinal shear capacity. Despite the several deterministic research findings leading to the development of proposals and modifications on the complex shear characteristics of PDCS that defines its strength behaviour, the laboratory performance testing stands to be the only accurate means for the PDCS strength assessment. The issue is critical and warrants much further thoughts from different perspective other than the deterministic approach that are rather expensive and time consuming. Hence, the development of a rational-based numerical test load function from longitudinal shear capacity consideration is a necessity in augmenting the previous futile attempts for strength determination of PDCS devoid of the costlier and expensive laboratory procedure.

  20. Eye Tracking Metrics for Workload Estimation in Flight Deck Operation

    Science.gov (United States)

    Ellis, Kyle; Schnell, Thomas

    2010-01-01

    Flight decks of the future are being enhanced through improved avionics that adapt to both aircraft and operator state. Eye tracking allows for non-invasive analysis of pilot eye movements, from which a set of metrics can be derived to effectively and reliably characterize workload. This research identifies eye tracking metrics that correlate to aircraft automation conditions, and identifies the correlation of pilot workload to the same automation conditions. Saccade length was used as an indirect index of pilot workload: Pilots in the fully automated condition were observed to have on average, larger saccadic movements in contrast to the guidance and manual flight conditions. The data set itself also provides a general model of human eye movement behavior and so ostensibly visual attention distribution in the cockpit for approach to land tasks with various levels of automation, by means of the same metrics used for workload algorithm development.

  1. Acceptance as a Normative Aspect of the Process of Coming to Understand Emotionally Charged Concepts: Upper-Secondary School Students Make Meaning of Gender

    Science.gov (United States)

    Trostek, Jonas R.

    2016-01-01

    Previous research on how students' acceptance of emotionally charged theories relates to their understanding is based on the measurement of acceptance and understanding as two separate variables. As an alternative, the present study takes a qualitative approach with the aim of exploring what 24 upper-secondary school students accept when they come…

  2. Fatigue Assessment of Full-Scale Retrofitted Orthotropic Bridge Decks

    NARCIS (Netherlands)

    Teixeira De Freitas, S.; Kolstein, M.H.; Bijlaard, F.S.K.

    2017-01-01

    Full-scale fatigue tests were performed on two retrofitted orthotropic bridge decks (OBDs). The retrofitting systems consist of adding a second steel plate on the top of the existing deck. The aim is to reduce the stresses at the fatigue-sensitive details and therefore extend the fatigue life of

  3. Rapid replacement of bridge deck expansion joints study - phase I.

    Science.gov (United States)

    2014-12-01

    Bridge deck expansion joints are used to allow for movement of the bridge deck due to thermal expansion, dynamics loading, and : other factors. More recently, expansion joints have also been utilized to prevent the passage of winter de-icing chemical...

  4. 46 CFR 45.143 - Hull openings above freeboard deck.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Hull openings above freeboard deck. 45.143 Section 45.143 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES GREAT LAKES LOAD LINES Conditions of Assignment § 45.143 Hull openings above freeboard deck. Closures for openings above...

  5. Critique of the Reggeized deck model

    International Nuclear Information System (INIS)

    Berger, E.L.

    1975-01-01

    A detailed analysis is presented of the Reggeized pion exchange Deck model for processes of the type ap → A*N → (a*π)N, where a = π, K, or nucleon and a* = rho, K*, N or Δ. Predictions of the model for both production and decay properties of the low mass system A* → (a*π) are derived and contrasted with data. Diffractive as well as charge exchange reactions are treated. The role of pion exchange in generating (a*π) enhancements near threshold and their properties is examined from several points of view. Characteristic exchange effects and quantum number properties (e.g., cross-overs) of the pion exchange Deck graph are shown to be verified in the data, but this graph alone is inadequate. The failures all point to the need for a second graph, having a* exchange properties. The contribution of a* exchange is roughly equal to that of the π exchange graph. (U.S.)

  6. Geno-toxicity assay of sediment and water samples from the Upper Silesia post-mining areas, Poland by means of Allium-test

    Energy Technology Data Exchange (ETDEWEB)

    Geras' kin, S.; Oudalova, A.; Michalik, B.; Dikareva, N.; Dikarev, V. [Russian Institute of Agricultural Radiology & Agroecology RAAS, Obninsk (Russian Federation)

    2011-05-15

    Genotoxic potential of two environmental compartments (water and sediment) from the Upper Silesia Coal Basin (USCB), Poland were evaluated and compared by employing root meristem cells of Allium cepa. The clear genotoxic effect of water and sediment sampled was shown, with an important contribution of severe types of cytogenetic abnormalities. The most biologically relevant pollutants were revealed through multivariate statistical analysis of relationships between biological effects registered and the environment contamination. Overall, results of simultaneous use of conventional monitoring methods and biological tests suggested that contemporary levels of persistent pollutants in post-mining areas of the USCB may enhance the risk both for human health and biological components of natural ecosystems.

  7. Design of Experimental Suspended Footbridge with Deck Made of UHPC

    Directory of Open Access Journals (Sweden)

    Blank Marek

    2016-01-01

    Full Text Available This paper deals with the static and dynamic design of experimental footbridge for pedestrians and cyclists in the municipality Lužec nad Vltavou in Czech Republic, Europe. This work aims to familiarize the reader with calculations carried out and the results obtained, describing the static and dynamic properties of proposed footbridge. The construction of footbridge is designed as a suspended structure with prestressed bridge deck consisting of prefabricated UHPC panels and reversed “V” shaped steel pylon with height of approximately 40 meters. The deck is anchored using 24 steel hangers in one row in a steel pylon - 17 ropes in the main span and 7 cables on the other side. Range of the main span is 99.18 meters and the secondary span is 31.9 m. Deck width is 4.5 meters with 3.0 meters passing space. The bridge is designed for the possibility of passage of vehicles weighting up to 3.5 tons. Deck panels are made of UHPC with reinforcement. At the edge of the bridge on the side of the shorter span the bridge deck is firmly connected with abutment and on the other deck it is stored using a pair of sliding bearings. The utilization of the excellent properties of UHPC allows to design a very thin and lightweight construction of the deck, which could not be achieved with the use of normal concrete.

  8. Experiments and theory on deck and girder crushing

    DEFF Research Database (Denmark)

    Simonsen, Bo Cerup; Ocakli, Hasan

    1999-01-01

    -deflection curves and modes of deformation for decks, stringer decks and deep thin-walled beams subjected to central or excentric point loads between transverse frames. Based on theory and experiments, various modelling aspects of the local/global failure of the beams are discussed. The agreement between......This paper is concerned with theoretical and experimental analysis of deep plastic collapse of a deck or deep girder subjected to an in-plane, concentrated load. A theory is derived which is valid until initition of fracture in the structure. The presented experimental results show load...

  9. A feasibility study of bridge deck deicing using geothermal energy.

    Science.gov (United States)

    2015-04-01

    In this study, we investigated the feasibility of a ground-coupled system that utilizes heat energy harvested from the ground for : deicing of bridge decks. Heat exchange is performed using circulation loops integrated into the deep foundations suppo...

  10. Precision monitoring of bridge deck curvature change during replacement.

    Science.gov (United States)

    2016-05-01

    This project was focused on development and deployment of a system for monitoring vertical : displacement in bridge decks and bridge spans. The system uses high precision wireless inclinometer : sensors to monitor inclinations at various points of a ...

  11. Bridge deck concrete volume change : final contract report.

    Science.gov (United States)

    2010-02-01

    Concrete structures such as bridge decks, with large surface area relative to volume, shrink and crack, thus reducing service life performance and increasing operation costs. The project evaluated the early, first 24 hours, and long-term, 180 days, s...

  12. Evaluation of bridge deck with shrinkage-compensating concrete.

    Science.gov (United States)

    2016-04-01

    Concrete bridge decks are susceptible to premature cracking and to corrosion of reinforcing steel. Low-permeability : concrete does not always ensure durability if the concrete has excessive cracks that facilitate the intrusion of aggressive solution...

  13. Multidisciplinary health monitoring of a steel bridge deck structure

    NARCIS (Netherlands)

    Pahlavan, P.L.; Pijpers, R.J.M.; Paulissen, J.H.; Hakkesteegt, H.C.; Jansen, T.H.

    2013-01-01

    Fatigue cracks in orthotropic bridge decks are an important cause for the necessary renovation of existing bridges. Parallel utilization of various technologies based on different physical sensing principles can potentially maximize the efficiency of structural health monitoring (SHM) systems for

  14. Structural Loading of Cross Deck Connections for Trimaran Vessels

    National Research Council Canada - National Science Library

    Rhoads, Jason

    2004-01-01

    ...: longitudinal bending, transverse bending, torsional bending, spreading and squeezing of hulls, inner and outer hull slam pressures, wet deck slam pressures, loading from ship's motions, and whipping of slender hulls...

  15. Experimental studies on multicellular GFRP bridge deck panels ...

    Indian Academy of Sciences (India)

    M P MUTHURAJ

    2017-11-20

    Nov 20, 2017 ... design of a new bridge deck panel made of GFRP. .... cient manufacturing processes with minimal wastage. But re-use of the remaining FRP elements during manufacture ... Energy consumption for production of different.

  16. Smart FRP Composite Sandwich Bridge Decks in Cold Regions

    Science.gov (United States)

    2011-07-01

    In this study, new and integrated Smart honeycomb Fiber-Reinforced Polymer (S-FRP) : sandwich materials for various transportation construction applications, with particular emphasis : on highway bridge decks in cold regions, were developed and teste...

  17. Shrinkage and durability study of bridge deck concrete.

    Science.gov (United States)

    2010-12-01

    The Mississippi Department of Transportation is incorporating changes to material : specifications and construction procedures for bridge decks in an effort to reduce shrinkage : cracking. These changes are currently being implemented into a limited ...

  18. WORM: A general-purpose input deck specification language

    International Nuclear Information System (INIS)

    Jones, T.

    1999-01-01

    Using computer codes to perform criticality safety calculations has become common practice in the industry. The vast majority of these codes use simple text-based input decks to represent the geometry, materials, and other parameters that describe the problem. However, the data specified in input files are usually processed results themselves. For example, input decks tend to require the geometry specification in linear dimensions and materials in atom or weight fractions, while the parameter of interest might be mass or concentration. The calculations needed to convert from the item of interest to the required parameter in the input deck are usually performed separately and then incorporated into the input deck. This process of calculating, editing, and renaming files to perform a simple parameter study is tedious at best. In addition, most computer codes require dimensions to be specified in centimeters, while drawings or other materials used to create the input decks might be in other units. This also requires additional calculation or conversion prior to composition of the input deck. These additional calculations, while extremely simple, introduce a source for error in both the calculations and transcriptions. To overcome these difficulties, WORM (Write One, Run Many) was created. It is an easy-to-use programming language to describe input decks and can be used with any computer code that uses standard text files for input. WORM is available, via the Internet, at worm.lanl.gov. A user's guide, tutorials, example models, and other WORM-related materials are also available at this Web site. Questions regarding WORM should be directed to wormatlanl.gov

  19. [Function analysis of employees at cash desks in the retailing sector by means of the study of the movements of the upper limbs].

    Science.gov (United States)

    Molinaro, V; Del Ferraro, S

    2007-01-01

    Supermarket checkouts are different in term of dimensions and arrangement of the essential devices for cashier's work. It means that a different layout can involve different tasks, so it is necessary to evaluate every single system in order to define the entity of required commitment for the worker. A supermarket checkout was considered in order to evaluate its workstation and to analyze the different tasks of two cashiers with similar anthropometric measurements. In particular one of them is affected by a widespread osteoarthritis, verified by instrumental tests and clinical examination. Several geometrical measures of the workstation were carried out while the cashiers were observed and filmed by videotapes during their activities. The study has been carried out by drawing the "preferred" and "maximal" working areas, as UNI EN ISO 14738:2004 suggests. Some tasks seem to be particularly critical especially for the cashier affected by osteoarthritis, who adopts compensatory postural mechanisms in order to use some devices which are not easy to reach inside the workstation, and which can induce pain to her. Finally the authors make some considerations about the opportunity of making a new layout of the workstation in order to find a more suitable arrangement of the devices.

  20. Hybrid FRP-concrete bridge deck system final report I : development and system performance validation.

    Science.gov (United States)

    2009-10-01

    In this study, the concept of the hybrid FRP-concrete structural systems was applied to both bridge : superstructure and deck systems. Results from the both experimental and computational analysis for : both the hybrid bridge superstructure and deck ...

  1. Rapid replacement of Tangier Island bridges including lightweight and durable fiber-reinforced polymer deck systems.

    Science.gov (United States)

    2009-01-01

    Fiber-reinforced polymer (FRP) composite cellular deck systems were used as new bridge decks on two replacement bridges on Tangier Island, Virginia. The most important characteristics of this application were reduced self-weight and increased durabil...

  2. Dynamic assessment of bridge deck performance considering realistic bridge-traffic interaction

    Science.gov (United States)

    2017-09-01

    Concrete bridge decks are directly exposed to daily traffic loads and may experience some surface cracking caused by excessive stress or fatigue accumulation, which requires repair or replacement. Among typical bridges in North America, bridge decks ...

  3. Dynamic assessment of bridge deck performance considering realistic bridge-traffic interaction : research brief

    Science.gov (United States)

    2017-09-01

    This study is to develop simulation methodology to conduct the dynamic assessment of bridge deck performance subjected to traffic. Concrete bridge decks are exposed to daily traffic loads and may experience some surface cracking caused by excessive s...

  4. Aircraft Carrier Flight and Hangar Deck Fire Protection: History and Current Status

    National Research Council Canada - National Science Library

    Darwin, Robert L; Bowman, Howard L; Hunstad, Mary; Leach, William B; Williams, Frederick W

    2005-01-01

    .... Next, a review of firefighting systems, including the firefighting agents currently in use, as well as the current tactics for fighting fires on the flight deck and the hangar deck, is provided...

  5. "The Battery" designed with Super-Light (concrete) Decks

    DEFF Research Database (Denmark)

    Castberg, Niels Andreas; Hertz, Kristian Dahl

    This paper describes how Super-Light structures can be used as a structural principle for the buildings in the project ‘The Battery’ designed by Bjarke Ingels Group. The overall structural concept is described and the advantages of using super-light slabs for the project are explored. Especially...... the cantilevered internal corridors are investigated. Super-Light Structures is a newly patented structural concrete concept. Slabs based on the concept are the first structural element developed under the patent. The slabs called SL-decks have multiple advantages compared to traditional hollow core slabs....... The paper aims to describe the concept of how the deck can be used in these innovative buildings and how the special advantages of the SL-decks are applied....

  6. Issues in bridge deck damage evaluation using aerial photos

    Science.gov (United States)

    Natarajan, M.; Chen, S. E.; Boyle, C.; Martin, E.; Hauser, E.

    2012-04-01

    Small format aerial photography (SFAP) with low flying technique is proposed for damage evaluation of bridge decks. High resolution images obtained using under-belly photography can be used to quantify the various bridge deck problems. The conventional truck-mount or vehicle-mount deck imaging technologies require a large number of image samples. Hence the physical scanning is time consuming and it is also challenging consider the size and location of a bridge. Aerial imaging overcomes these issues, but they face different kinds of challenges that are posed by obstacles such as shadow from trees, power lines and vehicles, signs and luminaries structures. The image resolution uncertainty, which is a function of the pilot skills and flying conditions, may also add additional challenges to aerial imaging technique. Hence different image processing tools have to be integrated into a single package to achieve the desired task. This paper summarizes the challenges faced and the preliminary results are presented and discussed.

  7. PARAMETRIC STUDY OF SKEW ANGLE ON BOX GIRDER BRIDGE DECK

    OpenAIRE

    Shrikant D. Bobade *, Dr. Valsson Varghese

    2016-01-01

    Box girder bridge deck, is the most common type of bridges in world and India, it consists of several Slab or girders. The span in the direction of the roadway and connected across their tops and bottoms by a thin continuous structural stab, the longitudinal box girders can be made of steel or concrete. The Simple supported single span concrete bridge deck is presented in present study. Skewed bridges are suitable in highway design when the geometry of straight bridges is not possible. The sk...

  8. 46 CFR 109.575 - Accumulation of liquids on helicopter decks.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Accumulation of liquids on helicopter decks. 109.575... DRILLING UNITS OPERATIONS Miscellaneous § 109.575 Accumulation of liquids on helicopter decks. The master or person in charge shall ensure that no liquids are allowed to accumulate on the helicopter decks. ...

  9. Relationship between Deck Level, Body Surface Temperature and Carcass Damages in Italian Heavy Pigs after Short Journeys at Different Unloading Environmental Conditions.

    Science.gov (United States)

    Arduini, Agnese; Redaelli, Veronica; Luzi, Fabio; Dall'Olio, Stefania; Pace, Vincenzo; Nanni Costa, Leonardo

    2017-02-10

    In order to evaluate the relationships between deck level, body surface temperature and carcass damages after a short journey (30 min), 10 deliveries of Italian heavy pigs, including a total of 1400 animals from one farm, were examined. Within 5 min after the arrival at the abattoir, the vehicles were unloaded. Environmental temperature and relative humidity were recorded and a Temperature Humidity Index (THI) was calculated. After unloading, maximum temperatures of dorsal and ocular regions were measured by a thermal camera on groups of pigs from each of the unloaded decks. After dehairing, quarters and whole carcasses were evaluated subjectively by a trained operator for skin damage using a four-point scale. On the basis of THI at unloading, deliveries were grouped into three classes. Data of body surface temperature and skin damage score were analysed in a model including THI class, deck level and their interaction. Regardless of pig location in the truck, the maximum temperature of the dorsal and ocular regions increased with increasing THI class. Within each THI class, the highest and lowest body surface temperatures were found in pigs located on the middle and upper decks, respectively. Only THI class was found to affect the skin damage score ( p trucks, even at relatively low temperature and THI, in order to improve welfare and reduce loss of carcass value.

  10. Full-Scale Evaluation of DuraDeck (registered trademark) and MegaDeck (trademark) Matting Systems

    Science.gov (United States)

    2013-07-01

    plates studded with threaded bolts were placed ERDC/GSL TR-13-27 10 underneath two pre-drilled corners of the panel. The plates were positioned so...metal plates studded with threaded ERDC/GSL TR-13-27 4 Figure 1. DuraDeck® mat panel, top surface. Figure 2. DuraDeck® mat panel, bottom surface...ERDC/GSL TR-13-27 5 bolts , as shown in Figure 3, underneath the mat corners and then installing special connector nuts from the top surface

  11. A FORM ANALYSIS OF JAPANESE PEDESTRIAN DECKS AND EUROPEAN PLAZAS

    Directory of Open Access Journals (Sweden)

    ANDO Naomi

    2015-06-01

    Full Text Available This study compares Japanese pedestrian decks and European plazas as public pedestrian spaces. The characteristics of both types of spaces will be clarified through a schematic analysis. The connections of these spaces with their surroundings will also be analyzed. Further, the spatial image of these spaces are discussed. Pedestrian spaces in Romania will be discussed as well.

  12. Compressive Membrane Action in Prestressed Concrete Deck Slabs

    NARCIS (Netherlands)

    Amir, S.

    2014-01-01

    One of the most important questions that structural engineers all over the world are dealing with is the safety of the existing structures. In the Netherlands, there are a large number of transversely prestressed bridge decks that have been built in the last century and now need to be investigated

  13. The effect of floating deck structures on underwater radiated noise

    NARCIS (Netherlands)

    Bosschaart, C.; Jansen, H.W.; Jong, C.A.F. de; Basten, T.

    2017-01-01

    A concept for underwater machinery noise mitigation of future civil and military ships is the application of a common deck structure, supporting multiple machines, which is installed on resilient mounts on the ship's foundation structure. TNO is addressing the availability and testing of tools to be

  14. Development of MIDAS/SMR Input Deck for SMART

    International Nuclear Information System (INIS)

    Cho, S. W.; Oh, H. K.; Lee, J. M.; Lee, J. H.; Yoo, K. J.; Kwun, S. K.; Hur, H.

    2010-01-01

    The objective of this study is to develop MIDAS/SMR code basic input deck for the severe accidents by simulating the steady state for the SMART plant. SMART plant is an integrated reactor developed by KAERI. For the assessment of reactor safety and severe accident management strategy, it is necessary to simulate severe accidents using the MIDAS/SMR code which is being developed by KAERI. The input deck of the MIDAS/SMR code for the SMART plant is prepared to simulate severe accident sequences for the users who are not familiar with the code. A steady state is obtained and the results are compared with design values. The input deck will be improved through the simulation of the DBAs and severe accidents. The base input deck of the MIDAS/SMR code can be used to simulate severe accident scenarios after improvement. Source terms and hydrogen generation can be analyzed through the simulation of the severe accident. The information gained from analyses of severe accidents is expected to be helpful to develop the severe accident management strategy

  15. a finite element model for the analysis of bridge decks

    African Journals Online (AJOL)

    Dr Obe

    A FINITE ELEMENT MODEL FOR THE ANALYSIS OF BRIDGE DECKS. NIGERIAN JOURNAL OF TECHNOLOGY, VOL. 27 NO.1, MARCH 2008. 59. (a) Beam-plate system. (b) T-beam structural model. Fig. 1 Beam-plate structure idealisations. The matrix displacement method of analysis is used. The continuum structure is.

  16. Life-Cycle Inventory Analysis of Manufacturing Redwood Decking

    Science.gov (United States)

    Richard D. Bergman; Han-Sup Han; Elaine Oneil; Ivan L. Eastin

    2012-01-01

    Green building has become increasingly important. Therefore, consumers and builders often take into account the environmental attributes of a building material. This study determined the environmental attributes associated with manufacturing 38-mm × 138-mm (nominal 2 × 6) redwood decking in northern California using the life-cycle inventory method. Primary data...

  17. Fatigue Properties of Orthotropic Decks on Railway Bridges

    Czech Academy of Sciences Publication Activity Database

    Frýba, Ladislav; Gajdoš, Lubomír

    1999-01-01

    Roč. 21, č. 7 (1999), s. 639-652 ISSN 0141-0296 Grant - others:XX(CZ) ERRI D 191 Keywords : railway bridges * orthotropic decks * fatigue Subject RIV: JM - Building Engineering Impact factor: 0.364, year: 1999

  18. Punching shear strength of transversely prestressed concrete decks

    NARCIS (Netherlands)

    Amir, S.; Van der Veen, C.; Walraven, J.C.

    2012-01-01

    In the Netherlands, there is a need to determine the capacity of bridge decks as a large number of them were built back in the 60’s and 70’s. Since then, not only a lot of additional safety requirements have been incorporated into the modern codes but the traffic flow has also increased drastically.

  19. Investigation of Aerodynamic Interference between Twin Deck Bridges

    Energy Technology Data Exchange (ETDEWEB)

    Sitek, M. A. [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division. Transportation Research and Analysis Computing Center (TRACC); Bojanowski, C. [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division. Transportation Research and Analysis Computing Center (TRACC); Lottes, S. A. [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division. Transportation Research and Analysis Computing Center (TRACC)

    2016-05-01

    Construction of a twin bridge can be a cost effective and minimally disruptive way to increase capacity when an existing bridge is not near the end of its service life. With ever growing vehicular traffic, when demand approaches the capacity of many existing roads and bridges. Remodeling a structure with an insufficient number of lanes can be a good solution in case of smaller and less busy bridges. Closing down or reducing traffic on crossings of greater importance for the construction period, however, can result in major delays and revenue loss for commerce and transportation as well as increasing the traffic load on alternate route bridges. Multiple-deck bridges may be the answer to this issue. A parallel deck can be built next to the existing one, without reducing the flow. Additionally, a new bridge can be designed as a twin or multi-deck structure. Several such structures have been built throughout the United States, among them: - The New NY Bridge Project - the Tappan Zee Hudson River Crossing, - SR-182 Columbia River Bridge, - The Thaddeus Kosciusko Bridge (I-87), - The Allegheny River Bridge, Pennsylvania, which carries I76, - Fred Hartman Bridge, TX, see Figure 1.2. With a growing number of double deck bridges, additional, more detailed, studies on the interaction of such bridge pairs in windy conditions appears appropriate. Aerodynamic interference effects should be examined to assure the aerodynamic stability of both bridges. There are many studies on aerodynamic response of single deck bridges, but the literature on double-deck structures is not extensive. The experimental results from wind tunnels are still limited in number, as a parametric study is required, they can be very time consuming. Literature review shows that some investigation of the effects of gap-width and angle of wind incidence has been done. Most of the CFD computational studies that have been done were limited to 2D simulations. Therefore, it is desirable to investigate twin decks

  20. Causes of Early Age Cracking on Concrete Bridge Deck Expansion Joint Repair Sections

    Directory of Open Access Journals (Sweden)

    Jared R. Wright

    2014-01-01

    Full Text Available Cracking of newly placed binary Portland cement-slag concrete adjacent to bridge deck expansion dam replacements has been observed on several newly rehabilitated sections of bridge decks. This paper investigates the causes of cracking by assessing the concrete mixtures specified for bridge deck rehabilitation projects, as well as reviewing the structural design of decks and the construction and curing methods implemented by the contractors. The work consists of (1 a comprehensive literature review of the causes of cracking on bridge decks, (2 a review of previous bridge deck rehabilitation projects that experienced early-age cracking along with construction observations of active deck rehabilitation projects, and (3 an experimental evaluation of the two most commonly used bridge deck concrete mixtures. Based on the literature review, the causes of concrete bridge deck cracking can be classified into three categories: concrete material properties, construction practices, and structural design factors. The most likely causes of the observed early-age cracking were found to be inadequate curing and failure to properly eliminate the risk of plastic shrinkage cracking. These results underscore the significance of proper moist curing methods for concrete bridge decks, including repair sections. This document also provides a blueprint for future researchers to investigate early-age cracking of concrete structures.

  1. Hybrid FRP-concrete bridge deck system final report II : long term performance of hybrid FRP-concrete bridge deck system.

    Science.gov (United States)

    2009-06-01

    This report describes the investigation of the long term structural performance of a : hybrid FRP-concrete (HFRPC) bridge deck on steel girders. The study aimed at : assessing three long term aspects pertaining to the HFRPC bridge deck: (1) creep : c...

  2. Service Life and Maintenance Modelling of Reinforced Concrete Bridge Decks

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle

    Recent research in the area of assessment and maintenance of reinforced concrete bridge decks is presented in this paper. Three definitions of service lifetime are introduced and the difficult problem of assessing the service life is discussed. A stochastic modelling of corrosion and corrosion...... cracking is introduced and the site dependency of corrosion is stressed. Finally, a recently developed optimal repair strategy for bridges is briefly explained....

  3. Delamination Detection of Reinforced Concrete Decks Using Modal Identification

    Directory of Open Access Journals (Sweden)

    Shutao Xing

    2012-01-01

    Full Text Available This study addressed delamination detection of concrete slabs by analyzing global dynamic responses of structures. Both numerical and experimental studies are presented. In the numerical examples, delaminations with different sizes and locations were introduced into a concrete slab; the effects of presence, sizes, and locations of delaminations on the modal frequencies and mode shapes of the concrete slab under various support conditions were studied. In the experimental study, four concrete deck specimens with different delamination sizes were constructed, and experimental tests were conducted. Traditional peak-picking, frequency domain decomposition, and stochastic subspace identification methods were applied to the modal identification from dynamic response measurements. The modal parameters identified by these three methods correlated well. The changes in modal frequencies, damping ratios, and mode shapes that were extracted from the dynamic measurements were investigated and correlated to the actual delaminations and can indicate presence and severity of delamination. Finite element (FE models of reinforced concrete decks with different delamination sizes and locations were established. The modal parameters computed from the FE models were compared to those obtained from the laboratory specimens, and the FE models were validated. The delamination detection approach was proved to be effective for concrete decks on beams.

  4. Full Scale Investigation of the Dynamic Heat Storage of Concrete Decks with PCM and Enhanced Heat Transfer Surface Area

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew; Heiselberg, Per; Jensen, Rasmus Lund

    2013-01-01

    The paper presents the full-scale experimental investigation of the dynamic heat storage potential of the prefabricated hollow core deck elements with and without phase change material (PCM) and with and without increased bottom surface area of the decks. In the presented investigation five types...... of hollow core decks with different surfaces on the bottom are investigated: reference deck made of standard concrete and flat surface, deck with special mortar grooved tiles, deck with flat mortar tiles, deck with grooved mortar and phase change material tiles, deck with flat mortar and phase change...... material tiles. The experimental investigation presented in the paper is performed in the specially designed modified hot box apparatus that allows maintaining periodic steady-state tests with the full-scale concrete deck elements. The presented research investigates if the extended surface area and PCM...

  5. Numerical Analysis of Heat Storage and Heat Conductivity in the Concrete Hollow Core Deck Element

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew; Heiselberg, Per; Jensen, Rasmus Lund

    2011-01-01

    extent these simplified models estimate the heat storage potential of precast hollow-core concrete decks correctly. This study investigates various approaches on how to model the heat transfer within the air void in the deck. Furthermore, it is analysed how different heat transfer models influence...... the overall heat transfer and heat storage in the hollow-core decks. The presented results allow comparison between detailed results from 2D-COMSOL simulations and simple 1D calculations from the whole building simulation tool such as BSim program and moreover, it is possible to validate the calculation...... method in BSim for the concrete deck element with air voids. Finally, this paper presents a comparison of the calculated heat conductivity of the hollow-core concrete deck and the measured heat conductivity for the same deck by using hot box apparatus....

  6. Aerodynamic and aeroelastic characteristics of typical bridge decks equipped with wind barriers at the windward bridge-deck edge

    Czech Academy of Sciences Publication Activity Database

    Buljac, Andrija; Kozmar, H.; Pospíšil, Stanislav; Macháček, Michael

    2017-01-01

    Roč. 137, April (2017), s. 310-322 ISSN 0141-0296 R&D Projects: GA ČR(CZ) GA15-01035S; GA MŠk(CZ) LO1219 Keywords : bridge decks * roadway wind barrier * aerodynamic forces and moments * galloping * flutter * wind-tunnel experiments Subject RIV: JM - Building Engineering OBOR OECD: Construction engineering , Municipal and structural engineering Impact factor: 2.258, year: 2016 http://www.sciencedirect.com/science/ article /pii/S014102961730278X

  7. Recommendations for Longitudinal Post-Tensioning in Full-Depth Precast Concrete Bridge Deck Panels

    OpenAIRE

    Bowers, Susan Elizabeth

    2007-01-01

    Full-depth precast concrete panels offer an efficient alternative to traditional cast-in-place concrete for replacement or new construction of bridge decks. Research has shown that longitudinal post-tensioning helps keep the precast bridge deck in compression and avoid problems such as leaking, cracking, spalling, and subsequent rusting on the beams at the transverse panel joints. Current design recommendations suggest levels of initial compression for precast concrete decks in a very limit...

  8. Characterization of stormwater runoff from bridge decks in eastern Massachusetts, 2014–16

    Science.gov (United States)

    Smith, Kirk P.; Sorenson, Jason R.; Granato, Gregory E.

    2018-05-02

    than 0.25 millimeters in diameter) dominated the SS matrix by more than an order of magnitude. Concentrations of LOI and PC in composite samples ranged from 15 to 1,740 mg/L and 6.68 to 1,360 mg/L, respectively, and generally represented less than 10 and 3 percent of the median mass of SS, respectively. Concentrations of TP in composite samples ranged from 0.09 to 7.02 mg/L; median concentrations of TP ranged from 0.505 to 0.69 mg/L and were highest on the bridge on State Route 2A in Boston. Concentrations of total nitrogen (TN) (sum DN and PN) in composite samples were variable (0.36 to 29 mg/L). Median DN (0.64 to 0.90 mg/L) concentrations generally represented about 40 percent of the TN concentration at each bridge and were similar to annual volume-weighted mean concentrations of nitrogen in precipitation in Massachusetts.Nonparametric statistical methods were used to test for differences between sample constituent concentrations among the three bridges. These results indicated that there are no statistically significant differences for concentrations of SS, LOI, PC, and TP among the three bridges (one-way analysis of variance test on rank-transformed data, 95-percent confidence level). Test results for concentrations of TN in composite samples indicated that concentrations of TN collected on State Route 20 near Quinsigamond Village were significantly higher than those concentrations collected on State Route 2A in Boston and Interstate 90 near Weston. Median concentrations of TN were about 93 and 55 percent lower at State Route 2A and at Interstate 90, respectively, compared to the median concentrations of TN at State Route 20.Samples of sediment were collected from five fixed locations on each bridge on three occasions during dry weather to calculate semiquantitative distributions of sediment yields on the bridge surface relative to the monitoring location. Mean yields of bridge-deck sediment during this study for State Route 2A in Boston, Interstate 90 near Weston

  9. Investigation of Flow Behavior around Corotating Blades in a Double-Spindle Lawn Mower Deck

    OpenAIRE

    Chon W.; Amano R. S.

    2005-01-01

    When the airflow patterns inside a lawn mower deck are understood, the deck can be redesigned to be efficient and have an increased cutting ability. To learn more, a combination of computational and experimental studies was performed to investigate the effects of blade and housing designs on a flow pattern inside a 1.1m wide corotating double-spindle lawn mower deck with side discharge. For the experimental portion of the study, air velocities inside the deck were measured using a laser Do...

  10. Vertical impedance measurements on concrete bridge decks for assessing susceptibility of reinforcing steel to corrosion

    Science.gov (United States)

    Bartholomew, Paul D.; Guthrie, W. Spencer; Mazzeo, Brian A.

    2012-08-01

    Corrosion is a pressing problem for aging concrete infrastructure, especially bridge decks. Because of its sensitivity to factors that affect corrosion of reinforcing steel in concrete, resistivity is an important structural health indicator for reinforced concrete structures. In this research, an instrument was developed to measure vertical impedance on concrete bridge decks. Measurements of vertical impedance on slabs prepared in the laboratory, on slabs removed from decommissioned bridge decks, and on an in-service bridge deck in the field demonstrate the utility of the new apparatus.

  11. Preparation of Input Deck to analyze the Nuclear Power Plant for the Use of Regulatory Verification

    International Nuclear Information System (INIS)

    Kang, Doo Hyuk; Kim, Hyung Seok; Suh, Jae Seung; Ahn, Seung Hoon

    2009-01-01

    The objectives of this paper are to make out the input deck that analyzes a nuclear power plant for the use of regulatory verification and to produce its calculation note. We have been maintained the input deck of T/H safety codes used in existing domestic reactors to ensure independent and accurate regulatory verification for the thermal-hydraulic safety analysis in domestic NPPs. This paper is mainly divided into two steps: first step is to compare existing input deck to the calculation note in order to verify the consistency. Next step is to model 3-dimensional reactor pressure vessel using MULTID component instead of the 1D existing input deck

  12. Flight Deck Weather Avoidance Decision Support: Implementation and Evaluation

    Science.gov (United States)

    Wu, Shu-Chieh; Luna, Rocio; Johnson, Walter W.

    2013-01-01

    Weather related disruptions account for seventy percent of the delays in the National Airspace System (NAS). A key component in the weather plan of the Next Generation of Air Transportation System (NextGen) is to assimilate observed weather information and probabilistic forecasts into the decision process of flight crews and air traffic controllers. In this research we explore supporting flight crew weather decision making through the development of a flight deck predicted weather display system that utilizes weather predictions generated by ground-based radar. This system integrates and presents this weather information, together with in-flight trajectory modification tools, within a cockpit display of traffic information (CDTI) prototype. that the CDTI features 2D and perspective 3D visualization models of weather. The weather forecast products that we implemented were the Corridor Integrated Weather System (CIWS) and the Convective Weather Avoidance Model (CWAM), both developed by MIT Lincoln Lab. We evaluated the use of CIWS and CWAM for flight deck weather avoidance in two part-task experiments. Experiment 1 compared pilots' en route weather avoidance performance in four weather information conditions that differed in the type and amount of predicted forecast (CIWS current weather only, CIWS current and historical weather, CIWS current and forecast weather, CIWS current and forecast weather and CWAM predictions). Experiment 2 compared the use of perspective 3D and 21/2D presentations of weather for flight deck weather avoidance. Results showed that pilots could take advantage of longer range predicted weather forecasts in performing en route weather avoidance but more research will be needed to determine what combinations of information are optimal and how best to present them.

  13. Super-light concrete decks for building floor slabs

    DEFF Research Database (Denmark)

    Hertz, Kristian Dahl; Castberg, Niels Andreas; Christensen, Jacob

    2014-01-01

    to flexibility, sound insulation and fire resistance compared with present-day prefabricated structures. Full-scale tests and theoretical investigations show that the deck structure performs as intended. Also, that it is possible to assess by calculation the loadbearing capacity in bending and shear, and assess...... the pull-out strength of prestressing wires, the fire resistance and the acoustic insulation. Based on the results of the investigations, recommendations are given for further development of the structure before fully automated mass production is established....

  14. Advanced flight deck/crew station simulator functional requirements

    Science.gov (United States)

    Wall, R. L.; Tate, J. L.; Moss, M. J.

    1980-01-01

    This report documents a study of flight deck/crew system research facility requirements for investigating issues involved with developing systems, and procedures for interfacing transport aircraft with air traffic control systems planned for 1985 to 2000. Crew system needs of NASA, the U.S. Air Force, and industry were investigated and reported. A matrix of these is included, as are recommended functional requirements and design criteria for simulation facilities in which to conduct this research. Methods of exploiting the commonality and similarity in facilities are identified, and plans for exploiting this in order to reduce implementation costs and allow efficient transfer of experiments from one facility to another are presented.

  15. Relationship between Deck Level, Body Surface Temperature and Carcass Damages in Italian Heavy Pigs after Short Journeys at Different Unloading Environmental Conditions

    Directory of Open Access Journals (Sweden)

    Agnese Arduini

    2017-02-01

    Full Text Available In order to evaluate the relationships between deck level, body surface temperature and carcass damages after a short journey (30 min, 10 deliveries of Italian heavy pigs, including a total of 1400 animals from one farm, were examined. Within 5 min after the arrival at the abattoir, the vehicles were unloaded. Environmental temperature and relative humidity were recorded and a Temperature Humidity Index (THI was calculated. After unloading, maximum temperatures of dorsal and ocular regions were measured by a thermal camera on groups of pigs from each of the unloaded decks. After dehairing, quarters and whole carcasses were evaluated subjectively by a trained operator for skin damage using a four-point scale. On the basis of THI at unloading, deliveries were grouped into three classes. Data of body surface temperature and skin damage score were analysed in a model including THI class, deck level and their interaction. Regardless of pig location in the truck, the maximum temperature of the dorsal and ocular regions increased with increasing THI class. Within each THI class, the highest and lowest body surface temperatures were found in pigs located on the middle and upper decks, respectively. Only THI class was found to affect the skin damage score (p < 0.05, which increased on quarters and whole carcasses with increasing THI class. The results of this study on short-distance transport of Italian heavy pigs highlighted the need to control and ameliorate the environmental conditions in the trucks, even at relatively low temperature and THI, in order to improve welfare and reduce loss of carcass value.

  16. Development and layout of a protocol for the field performance of concrete deck and crack sealers.

    Science.gov (United States)

    2009-09-01

    The main objective of this project was to develop and layout a protocol for the long-term monitoring and assessment of the performance of concrete deck and crack sealants in the field. To accomplish this goal, a total of six bridge decks were chosen ...

  17. 46 CFR 45.135 - Hull openings at or below freeboard deck.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Hull openings at or below freeboard deck. 45.135 Section 45.135 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES GREAT LAKES LOAD LINES Conditions of Assignment § 45.135 Hull openings at or below freeboard deck. Closures for hull...

  18. 46 CFR 108.133 - Hull superstructure, structural bulkheads, decks, and deckhouses.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull superstructure, structural bulkheads, decks, and deckhouses. 108.133 Section 108.133 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A... Protection § 108.133 Hull superstructure, structural bulkheads, decks, and deckhouses. Each hull...

  19. STS-37 Commander Nagel in commanders seat on OV-104's flight deck

    Science.gov (United States)

    1991-01-01

    STS-37 Commander Steven R. Nagel, wearing launch and entry suit (LES), sits at commanders station on the forward flight deck of Atlantis, Orbiter Vehicle (OV) 104. Surrounding Nagel are the seat headrest, control panels, checklists, forward flight deck windows, and three drinking water containers with straws attached to forward panel F2.

  20. Super-Light Prefabricated Deck Element Integrated in Traditional Concrete Prefabricated Element Construction

    DEFF Research Database (Denmark)

    Christensen, Jacob Ellehauge; Hertz, Kristian Dahl

    Super-light structures in form of deck elements have been used for the first time in a building to construct indoor pedestrian bridges. Examples of connections to external structures and other super-light deck elements are given along with other details. Other examples on the great versatility...

  1. decké osobnosti a vedení ve vědě

    Czech Academy of Sciences Publication Activity Database

    Wiedermann, Jiří

    č. 3 (2005), s. 14-17 ISSN 1210-9525 Institutional research plan: CEZ:AV0Z10300504 Keywords : vědecké osobnosti * talent * grantový systém * vědecká excelence Subject RIV: AM - Education http://abicko.avcr.cz/archiv/2005/3/obsah/vedecke-osobnosti-a-vedeni-ve-vede.html

  2. 29 CFR 1915.73 - Guarding of deck openings and edges.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Guarding of deck openings and edges. 1915.73 Section 1915.73 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION..., Ladders and Other Working Surfaces § 1915.73 Guarding of deck openings and edges. (a) The provisions of...

  3. Investigation of Flow Behavior around Corotating Blades in a Double-Spindle Lawn Mower Deck

    Directory of Open Access Journals (Sweden)

    Chon W.

    2005-01-01

    Full Text Available When the airflow patterns inside a lawn mower deck are understood, the deck can be redesigned to be efficient and have an increased cutting ability. To learn more, a combination of computational and experimental studies was performed to investigate the effects of blade and housing designs on a flow pattern inside a 1.1m wide corotating double-spindle lawn mower deck with side discharge. For the experimental portion of the study, air velocities inside the deck were measured using a laser Doppler velocimetry (LDV system. A high-speed video camera was used to observe the flow pattern. Furthermore, noise levels were measured using a sound level meter. For the computational fluid dynamics (CFD work, several arbitrary radial sections of a two-dimensional blade were selected to study flow computations. A three-dimensional, full deck model was also developed for realistic flow analysis. The computational results were then compared with the experimental results.

  4. Analysis of an Orthotropic Deck Stiffened with a Cement-Based Overlay

    DEFF Research Database (Denmark)

    Walter, Rasmus; Olesen, John Forbes; Stang, Henrik

    2007-01-01

    decks. A solution might be to enhance the stiffness of the traditional orthotropic bridge deck by using a cement-based overlay. In this paper, an orthotropic steel bridge deck stiffened with a cement-based overlay is analyzed. The analysis is based on nonlinear fracture mechanics, and utilizes......Over the past years, with increasing traffic volumes and higher wheel loads, fatigue damage in steel parts of typical orthotropic steel bridge decks has been experienced on heavily trafficked routes. A demand exists to find a durable system to increase the fatigue safety of orthotropic steel bridge...... the finite-element method. The stiffness of the steel deck reinforced with an overlay depends highly on the composite action. The composite action is closely related to cracking of the overlay and interfacial cracking between the overlay and underlying steel plate (debonding). As an example, a real size...

  5. Dynamic Heat Storage and Cooling Capacity of a Concrete Deck with PCM and Thermally Activated Building System

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew; Heiselberg, Per; Jensen, Rasmus Lund

    2012-01-01

    This paper presents a heat storage and cooling concept that utilizes a phase change material (PCM) and a thermally activated building system (TABS) implemented in a hollow core concrete deck. Numerical calculations of the dynamic heat storage capacity of the hollow core concrete deck element...... in the article highlight the potential of using TABS and PCM in a prefabricated concrete deck element....

  6. Heat Storage Performance of the Prefabricated Hollow Core Concrete Deck Element with Integrated Microencapsulated Phase Change Material

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew; Heiselberg, Per; Jensen, Rasmus Lund

    2012-01-01

    The paper presents the numerically calculated dynamic heat storage capacity of the prefabricated hollow core concrete deck element with and without microencapsulated phase change material (PCM). The reference deck is the ordinary deck made of standard concrete material and that is broadly used...

  7. Evaluation of bridge decks using non-destructive evaluation (NDE) at near highway speeds for effective asset management.

    Science.gov (United States)

    2015-06-01

    Remote sensing technologies allow for the condition evaluation of bridge decks at near highway speed. : Data collection at near highway speed for assessment of the top of the concrete deck and proof of : concept testing for the underside of the deck ...

  8. Static and fatigue investigation of second generation steel free bridge decks

    International Nuclear Information System (INIS)

    Klowak, C.; Memon, Amjad H.; Mufti, Aftab A.

    2006-01-01

    This paper outlines the static and fatigue behavior of two different cast-in-place second generation steel-free bridge decks, which are: hybrid carbon fiber reinforced polymer (CFRP); and glass fiber reinforced polymer (GFRP) and steel strap design. Although cast monolithically, the first deck slab was divided into three segments with different reinforcement configurations. All three segments were tested under a 222kN cyclic loading to investigate fatigue behavior. The second bridge deck comprised an internal panel and two cantilevers and was equipped with a civionics system. The internal panel static test that this paper deals with is useful in the development of fatigue theory derived from fatigue testing of the first bridge deck. Test results form the cyclic loading of the first bridge deck indicated that the cross-sectional area of the reinforcement used in the test bridge deck can be reduced by 40% based on the reinforcement provided in the deck under service loads. The hybrid system also reduced the development of longitudinal crack widths to approximately 0.4 mm under service conditions, compared to the cracks that occurred approximately halfway between adjacent bridge girders that were determined to be roughly 1 mm in several first generation steel-free bridge decks constructed in Canada. Civionics, also discussed in the paper, is a new term coined from Civil-Electronics, which is the application of electronics to civil structures. The Civionics Specifications (2004) developed by ISIS Canada researchers are a helpful design tool for engineers and contractors to develop civionics and structural health monitoring systems for civil infrastructure that will last the lifetime of a structure. The use of civionics for the second test bridge deck ensured the survival of 100% of the 63 internal sensors throughout the rigors of the construction and casting of the deck. (author)

  9. Unmanned Ground Vehicle for Autonomous Non-Destructive Testing of FRP Bridge Decks

    Science.gov (United States)

    Klinkhachorn, P.; Mercer, A. Scott; Halabe, Udaya B.; GangaRao, Hota V. S.

    2007-03-01

    Current non-destructive techniques for defect analysis of FRP bridge decks have a narrow scope. These techniques are very good at detecting certain types of defects but are not robust enough to detect all defects by themselves. For example, infrared thermography (IRT) can detect air filled defects and Ground Penetrating Radar (GPR) is good at detecting water filled ones. These technologies can be combined to create a more robust defect detection scheme. To accomplish this, an Unmanned Ground Vehicle (UGV) has been designed that incorporates both IR and GPR analysis to create a comprehensive defect map of a bridge deck. The UGV autonomously surveys the deck surface and acquires data. The UGV has two 1.5 GHz ground coupled GPR antennas that are mounted on the front of the UGV to collect GPR data. It also incorporates an active heating source and a radiometric IR camera to capture IR images of the deck, even in less than ideal weather scenarios such as cold cloudy days. The UGV is designed so that it can collect data in an assembly line fashion. It moves in 1 foot increments. When moving, it collects GPR data from the two antennas. When it stops it heats a section of the deck. The next time it stops to heat a section, the IR camera is analyzing the preheated deck section while preparing for the next section. Because the data is being continually collected using this method, the UGV can survey the entire deck in an efficient and timely manner.

  10. Experimental Test for Benchmark 1--Deck Lid Inner Panel

    International Nuclear Information System (INIS)

    Xu Siguang; Lanker, Terry; Zhang, Jimmy; Wang Chuantao

    2005-01-01

    The Benchmark 1 deck lid inner is designed for both aluminum and steel based on a General Motor Corporation's current vehicle product. The die is constructed with a soft tool material. The die successfully produced aluminum and steel panels without splits and wrinkles. Detailed surface strains and thickness measurement were made at selected sections to include a wide range of deformation patterns from uniaxial tension mode to bi-axial tension mode. The springback measurements were done by using CMM machine along the part's hem edge which is critical to correct dimensional accuracy. It is expected that the data obtained will provide a useful source for forming and springback study on future automotive panels

  11. CRASH TEST AND EVALUATION OF RESTRAINED SAFETY-SHAPE CONCRETE BARRIERS ON CONCRETE BRIDGE DECK

    Science.gov (United States)

    2018-01-01

    This research designed and tested a new portable concrete barrier that meets the performance of MASH TL-4 and can be used in temporary and permanent applications on bridge decks. Additionally, this new barrier system will minimize deflection, allowin...

  12. Abrasion-resistant concrete mix designs for precast bridge deck panels.

    Science.gov (United States)

    2010-08-01

    The report documents laboratory investigations undertaken to develop high performance concrete (HPC) for precast and pre-stressed bridge deck components that would reduce the life-cycle cost of bridges by improving the studded tire wear (abrasion) re...

  13. Structural design guidelines for concrete bridge decks reinforced with corrosion-resistant reinforcing bars.

    Science.gov (United States)

    2014-10-01

    This research program develops and validates structural design guidelines and details for concrete bridge decks with : corrosion-resistant reinforcing (CRR) bars. A two-phase experimental program was conducted where a control test set consistent : wi...

  14. Fluid-structure interaction analysis of a deck structure during a HCDA

    International Nuclear Information System (INIS)

    Kulak, R.F.

    1979-01-01

    Presented is an assessment of the structural integrity of the deck structure of a pool-type LMFBR during a Hypothetical Core Disruptive Accident (HCDA). During this accident the sodium above the core is propelled upward until it impacts against the deck structure. This hydrodynamic loading could produce (1) significant structural damage and (2) sodium leak paths. A finite-element model is used to study the deck dynamics during slug impact. By using the symmetry of the system, a sector model which accounts for the salient features of the system is developed. The main radial I-beam, component support I-beam and bottom annular plate are modeled using triangular plate elements. The concrete fill is modeled using hexahedral continuum elements. Using the above finite-element model the dynamics of the deck during a HCDA are investigated

  15. Performance of Rail Fastening Systems on an Open-Deck Bridge

    Science.gov (United States)

    2018-02-01

    Transportation Technology Center, Inc. (TTCI) monitored the performance of rail fasteners on an open-deck bridge and its approaches, located at Norfolk Southern Corporations (NS's) eastern mega site. The project was co-sponsored by the Federal Rai...

  16. Impact of overweight vehicles (with heavy axle loads) on bridge deck deterioration.

    Science.gov (United States)

    2012-03-01

    Bridge deck slabs develop compressive stresses from global flexural deformation and locally from high-level : wheel loads when it is subjected to overweight trucks. This study quantified the impact of overweight vehicles : with heavy axle loads on br...

  17. A Highly Accurate and Efficient Analytical Approach to Bridge Deck Free Vibration Analysis

    Directory of Open Access Journals (Sweden)

    D.J. Gorman

    2000-01-01

    Full Text Available The superposition method is employed to obtain an accurate analytical type solution for the free vibration frequencies and mode shapes of multi-span bridge decks. Free edge conditions are imposed on the long edges running in the direction of the deck. Inter-span support is of the simple (knife-edge type. The analysis is valid regardless of the number of spans or their individual lengths. Exact agreement is found when computed results are compared with known eigenvalues for bridge decks with all spans of equal length. Mode shapes and eigenvalues are presented for typical bridge decks of three and four span lengths. In each case torsional and non-torsional modes are studied.

  18. 3D laser scanning for quality control and assurance in bridge deck construction.

    Science.gov (United States)

    2014-08-01

    The inspection of installations of rebar and other embedded components in bridge deck construction is a tedious : task for eld inspectors, requiring considerable eld time for measurement and verication against code requirement. The verica...

  19. 75 FR 32902 - Wire Decking from the People's Republic of China: Final Affirmative Countervailing Duty...

    Science.gov (United States)

    2010-06-10

    ... Riqian Equipment Co., Ltd 437.11% Deyoma Wire Decking Factory 437.11% Global Storage Equipment... Dingxing Furniture Company 437.11% Tianjin Machinery Imp & Exp Corp 437.11% Tianjin Mandarin Import...

  20. Influence of fly ash, slag cement and specimen curing on shrinkage of bridge deck concrete.

    Science.gov (United States)

    2014-12-01

    Cracks occur in bridge decks due to restrained shrinkage of concrete materials. Concrete materials shrink as : cementitious materials hydrate and as water that is not chemically bonded to cementitious materials : migrates from the high humid environm...

  1. Flight Deck of the Future: Virtual Windows and e-textile iGear

    Data.gov (United States)

    National Aeronautics and Space Administration — The Flight Deck of the Future (F.F) will integrate interdisciplinary talent to design innovative, integrated human interfaces for the next generation of human...

  2. Latex-modified fiber-reinforced concrete bridge deck overlay : construction/interim report.

    Science.gov (United States)

    1993-06-01

    Latex-modified concrete (LMC) is Portland cement concrete (PCC) with an admixture of latex. LMC is considered to be nearly impermeable to chlorides and is extensively used to construct bridge deck overlays. Unfortunately, some of these overlays have ...

  3. ASSESSING CHILDREN'S EXPOSURES TO THE WOOD PRESERVATIVE CCA (CHROMATED COPPER ARSENATE) ON TREATED PLAYSETS AND DECKS

    Science.gov (United States)

    Concerns have been raised regarding the safety of young children contacting arsenic and chromium residues while playing on and around Chromated Copper Arsenate (CCA) treated wood playground structures and decks. Although CCA registrants voluntarily canceled treated wood for re...

  4. Performance evaluation of concrete bridge decks reinforced with MMFX and SSC rebars.

    Science.gov (United States)

    2006-01-01

    This report investigates the performance of bridge decks reinforced with stainless steel clad (SSC) and micro-composite multistructural formable steel (MMFX) rebars. The two-span Galloway Road Bridge on route CR5218 over North Elkhorn Creek in Scott ...

  5. Using artificial neural networks in the design of orthotropic bridge decks

    Directory of Open Access Journals (Sweden)

    Ahmed Shamel Fahmy

    2016-12-01

    Full Text Available For orthotropic bridge decks a lot of progress has been made in the development of codes to aid in the design process, in addition to software tools for numerical analysis and design. However, professional software tools will not aid the designer in choosing a preliminary economic layout at the conceptual design stage. Designers would go through iterative, lengthy and expensive procedures to reach the best configuration. The present research provides a methodology to investigate the contingency of using artificial neural networks for conceptual design of orthotropic steel-deck bridge. A neural network model was trained with different combinations of dimensions, and eight types of safety checks were performed on all of them. The resulting network can predict whether the deck is safe or not. It is found that this approach for the selection of orthotropic deck dimensions is a better and cost-effective option compared with international codes or expert opinion.

  6. Health monitoring of precast bridge deck panels reinforced with glass fiber reinforced polymer (GFRP) bars.

    Science.gov (United States)

    2012-03-01

    The present research project investigates monitoring concrete precast panels for bridge decks that are reinforced with Glass Fiber Reinforced Polymer (GFRP) bars. Due to the lack of long term research on concrete members reinforced with GFRP bars, lo...

  7. Fire modeling for Building 221-T - T Plant Canyon Deck and Railroad Tunnel

    International Nuclear Information System (INIS)

    Oar, D.L.

    1994-01-01

    This report was prepared by Hughes Associates, Inc. to document the results of fire models for building 221-T Canyon Deck and Railroad Tunnel. Backup data is contained in document No. WHC-SD-CP-ANAL-010, Rev. 0

  8. Human factors considerations in the design and evaluation of flight deck displays and controls

    Science.gov (United States)

    2013-11-01

    The objective of this effort is to have a single source document for human factors regulatory and guidance material for flight deck displays and controls, in the interest of improving aviation safety. This document identifies guidance on human factor...

  9. Concept design and alternate arrangements of orbiter mid-deck habitability features

    Science.gov (United States)

    Church, R. A.; Ciciora, J. A.; Porter, K. L.; Stevenson, G. E.

    1976-01-01

    The evaluations and recommendations for habitability features in the space shuttle orbiter mid-deck are summarized. The orbiter mission plans, the mid-deck dimensions and baseline arrangements along with crew compliments and typical activities were defined. Female and male anthropometric data based on zero-g operations were also defined. Evaluations of baseline and alternate feasible concepts provided several recommendations which are discussed.

  10. Field performance of timber bridges. 8, Lynches Woods Park stress-laminated deck bridge

    Science.gov (United States)

    J. P. Wacker; M. A. Ritter; D. Conger

    The Lynches Woods Park bridge was constructed during the summer of 1990 in Newberry, South Carolina. It is a single-span, single-lane, stress-laminated deck superstructure that measures approximately 30 ft long, 16 ft wide, and 14 in. deep. The bridge is unique in that is one of the first known stress-laminated deck bridges to be constructed of Southern Pine lumber...

  11. Field performance of timber bridges. 4, Graves Crossing stress-laminated deck bridge

    Science.gov (United States)

    J. P. Wacker; M. A. Ritter

    The Graves Crossing bridge was constructed October 1991 in Antrim County, Michigan, as part of the demonstration timber bridge program sponsored by the USDA Forest Service. The bridge is a two-span continuous, stress-laminated deck superstructure and it is 36-ft long and 26-ft wide. The bridge is one of the first stress-laminated deck bridges to be built of sawn lumber...

  12. Demonstration and Validation of a Composite Grid Reinforcement System for Bridge Decks

    Science.gov (United States)

    2016-09-01

    presence of chlorides from road salts that can pene- trate into the concrete deck and cause corrosion of standard steel reinforcement. Installation of the... Corrosion of Metal and Alloys – Corrosivity of Atmospheres – Classification, Determination and Estimation.” Geneva, Switzerland: International Standards...one year), an atmospheric corrosion test rack, (equipped with sensors to monitor corrosion and chlorides were in- serted in the bridge deck), and

  13. Analysis, prediction, and case studies of early-age cracking in bridge decks

    Science.gov (United States)

    ElSafty, Adel; Graeff, Matthew K.; El-Gharib, Georges; Abdel-Mohti, Ahmed; Mike Jackson, N.

    2016-06-01

    Early-age cracking can adversely affect strength, serviceability, and durability of concrete bridge decks. Early age is defined as the period after final setting, during which concrete properties change rapidly. Many factors can cause early-age bridge deck cracking including temperature change, hydration, plastic shrinkage, autogenous shrinkage, and drying shrinkage. The cracking may also increase the effect of freeze and thaw cycles and may lead to corrosion of reinforcement. This research paper presents an analysis of causes and factors affecting early-age cracking. It also provides a tool developed to predict the likelihood and initiation of early-age cracking of concrete bridge decks. Understanding the concrete properties is essential so that the developed tool can accurately model the mechanisms contributing to the cracking of concrete bridge decks. The user interface of the implemented computer Excel program enables the user to input the properties of the concrete being monitored. The research study and the developed spreadsheet were used to comprehensively investigate the issue of concrete deck cracking. The spreadsheet is designed to be a user-friendly calculation tool for concrete mixture proportioning, temperature prediction, thermal analysis, and tensile cracking prediction. The study also provides review and makes recommendations on the deck cracking based mainly on the Florida Department of Transportation specifications and Structures Design Guidelines, and Bridge Design Manuals of other states. The results were also compared with that of other commercially available software programs that predict early-age cracking in concrete slabs, concrete pavement, and reinforced concrete bridge decks. The outcome of this study can identify a set of recommendations to limit the deck cracking problem and maintain a longer service life of bridges.

  14. Disadvantageous Deck Selection in the Iowa Gambling Task: The Effect of Cognitive Load

    Directory of Open Access Journals (Sweden)

    Melissa J. Hawthorne

    2015-05-01

    Full Text Available Research has shown that cognitive load affects overall Iowa Gambling Task (IGT performance, but it is unknown whether such load impacts the selection of the individual decks that correspond to gains or losses. Here, participants performed the IGT either in a full attention condition or while engaged in a number monitoring task to divide attention. Results showed that the full attention group was more aware of the magnitude of gains or losses for each draw (i.e., payoff awareness than was the divided attention group. However, the divided attention group was more sensitive to the frequency of the losses (i.e., frequency awareness, as evidenced by their increased preference for Deck B, which is the large but infrequent loss deck. An analysis across blocks showed that the number monitoring group was consistently more aware of loss frequency, whereas the full attention group shifted between awareness of loss frequency and awareness of payoff amount. Furthermore, the full attention group was better able to weigh loss frequency and payoff amount when making deck selections. These findings support the notion that diminished cognitive resources may result in greater selection of Deck B, otherwise known as the prominent Deck B phenomenon.

  15. Embodied Energy Optimization of Prestressed Concrete Slab Bridge Decks

    Directory of Open Access Journals (Sweden)

    Julián Alcalá

    2018-04-01

    Full Text Available This paper presents one approach to the analysis and design of post-tensioned cast-in-place concrete slab bridge decks. A Simulated Annealing algorithm is applied to two objective functions: (i the economic cost; and (ii the embodied energy at different stages of production materials, transport, and construction. The problem involved 33 discrete design variables: five geometrical ones dealing with the thickness of the slab, the inner and exterior web width, and two flange thicknesses; concrete type; prestressing cables, and 26 variables for the reinforcement set-up. The comparison of the results obtained shows two different optimum families, which indicates that the traditional criteria of economic optimization leads to inefficient designs considering the embodied energy. The results indicate that the objectives are not competing functions, and that optimum energy designs are close to the optimum cost designs. The analysis also showed that the savings of each kW h of energy consumed carries an extra cost of 0.49€. The best cost solution presents 5.3% more embodied energy. The best energy solution is 9.7% more expensive than that of minor cost. In addition, the results have showed that the best cost solutions are not the best energy solutions.

  16. Structural assessment of roof decking using visual inspection methods

    International Nuclear Information System (INIS)

    Giller, R.A.; McCoy, R.M.; Wagenblast, G.R.

    1993-01-01

    The Hanford Site has approximately 1,100 buildings, some of which date back to the early 1940s. The roof on these buildings provides a weather resisting cover as well as the load resisting structure. Past experience has been that these roof structures may have structural modifications, the weather resisting membrane may have been replaced several times, and the members may experience some type of material degradation. This material degradation has progressed to cause the collapse of some roof deck members. The intent of the Hanford Site Central Engineering roof assessment effort is to provide an expedient structural assessment of the large number of buildings at the Hanford Site. This assessment is made by qualified structural inspectors following the open-quotes Preliminary Assessmentclose quotes procedures given in the American Society of Civil Engineers (ASCE) Standard ASCE 11-90. This roof assessment effort does not provide a total qualification of the roof for the design or in-place loads. This inspection does provide a reasonable estimate of the roof loading capacity to determine if personnel access restrictions are needed. A document search and a visual walkdown inspection provide the initial screening to identify modifications and components having questionable structural integrity. The structural assessment consists of baseline dead and live load stress calculations of all roofing components based on original design material strengths. The results of these assessments are documented in a final report which is retrievable in a form that future inspections will have comparative information

  17. ANDERS: future of concrete bridge deck evaluation and rehabilitation

    Science.gov (United States)

    Gucunski, Nenad; Moon, Franklin

    2011-04-01

    The Automated Nondestructive Evaluation and Rehabilitation System (ANDERS) aims to provide a uniquely comprehensive tool that will transform the manner in which bridge decks are assessed and rehabilitated. It is going to be achieved through: 1) much higher evaluation detail and comprehensiveness of detection at an early stage deterioration, 2) comprehensive condition and structural assessment at all stages of deterioration, and 3) integrated assessment and rehabilitation that will be minimally invasive, rapid and cost effective. ANDERS is composed of four systems. that merge novel imaging and NDE techniques, together with novel intervention approaches to arrest the deterioration processes. These technologies are incorporated within a series of human-operated and robotic vehicles. To perform assessments, ANDERS will be equipped with two complimentary nondestructive approaches. The first, Multi-Modal Nondestructive Evaluation (MM-NDE) System aims to identify and characterize localized deterioration with a high degree of resolution. The second, Global Structural Assessment (GSA) System aims to capture global structural characteristics and identify any appreciable effects of deterioration on a bridge structure. Output from these two approaches will be merged through a novel Automated Structural Identification (Auto St-Id) approach that will construct, calibrate, and utilize simulation models to assess overall structural vulnerability and capacity. These three systems comprise the assessment suite of ANDERS and will directly inform the Nondestructive Rehabilitation (NDR) System. The NDR System leverages robotics for the precision and rapid delivery of novel materials capable of halting the early-stage deterioration identified.

  18. Structural assessment of roof decking using visual inspection methods

    International Nuclear Information System (INIS)

    Giller, R.A.; McCoy, R.M.; Wagenblast, G.R.

    1993-10-01

    The Hanford Site has approximately 1,100 buildings, some of which date back to the early 1940s. The roof on these buildings provides a weather resisting cover as well as the load resisting structure. Past experience has been that these roof structures may have structural modifications, the weather resisting membrane may have been replaced several times, and the members may experience some type of material degradation. This material degradation has progressed to cause the collapse of some roof deck members. The intent of the Hanford Site Central Engineering roof assessment effort is to provide an expedient structural assessment of the large number of buildings at the Hanford Site. This assessment is made by qualified structural inspectors following the open-quotes Preliminary Assessment close-quote procedures given in the American Society of Civil Engineers (ASCE) Standard ASCE 11-90. This roof assessment effort does not provide a total qualification of the roof for the design or in-place loads. This inspection does provide a reasonable estimate of the roof loading capacity to determine if personnel access restrictions are needed. A document search and a visual walkdown inspection provide the initial screening to identify modifications and components having questionable structural integrity. The structural assessment consists of baseline dead and live load stress calculations of all roofing components based on original design material strengths. The results of these assessments are documented in a final report which is retrievable form that future inspections will have comparative information

  19. Composite Action in Prestressed NU I-Girder Bridge Deck Systems Constructed with Bond Breakers to Facilitate Deck Removal : Technical Summary

    Science.gov (United States)

    2017-11-01

    Results are reported from tests of small-scale push-off and large-scale composite NU I-girder specimens conducted to establish an interface connection detail that (1) Facilitates in-situ removal of the bridge deck without damaging prestressed girders...

  20. The Meaning of Meaning, Etc.

    Science.gov (United States)

    Nilsen, Don L. F.

    This paper attempts to dispel a number of misconceptions about the nature of meaning, namely that: (1) synonyms are words that have the same meanings, (2) antonyms are words that have opposite meanings, (3) homonyms are words that sound the same but have different spellings and meanings, (4) converses are antonyms rather than synonyms, (5)…

  1. Oriental upper blepharoplasty.

    Science.gov (United States)

    Weng, Chau-Jin

    2009-02-01

    Aesthetic surgery of the upper eyelids is a very common procedure performed in cosmetic practices around the world. The word blepharoplasty, however, has a different meaning in Asia than it does elsewhere. Orientals have different periorbital anatomic characteristics, their motivations for seeking eyelid treatment are different, and operative techniques have been adapted consequently. There are also many eyelid shapes among Orientals, mostly with regard to the presence and location of the supratarsal fold and/or presence of an epicanthal fold. The surgeon must therefore master a range of surgical procedures to treat these variations adequately. It is critical to know the indications for each blepharoplasty technique as well as their complications to select the right surgery and avoid unfavorable results. Epicanthoplasty performed on the right patient can greatly improve aesthetic results while retaining ethnic characteristics. This article will discuss Oriental eyelid characteristics, preoperative patient assessment, commonly used corrective techniques for the "double-eyelid" creation, and complications and how to avoid them.

  2. Application Side Casing on Open Deck RoRo to Improve Ship Stability

    Science.gov (United States)

    Hasanudin; K. A. P Utama, I.; Chen, Jeng-Horng

    2018-03-01

    RoRo is a vessel that can transport passengers, cargo, container and cars. Open Car Deck is favourite RoRo Vessel in developing countries due to its small GT, small tax and spacious car deck, but it has poor survival of stability. Many accident involve Open Car Deck RoRo which cause fatalities and victim. In order to ensure the safety of the ship, IMO had applied intact stability criteria IS Code 2008 which adapted from Rahola’s Research, but since 2008 IMO improved criteria become probabilistic damage stability SOLAS 2009. The RoRo type Open Car Deck has wide Breadth (B), small Draft (D) and small freeboard. It has difficulties to satisfy the ship’s stability criteria. Side Casings which has been applied in some RoRo have be known reduce freeboard or improve ship’s safety. In this paper investigated the effect side casings to survival of intact dan damage ship’s stability. Calculation has been conducted for four ships without, existing and full side casings. The investigation results shows that defect stability of Open Deck RoRo can be reduce with fitting side casing.

  3. Rapid multichannel impact-echo scanning of concrete bridge decks from a continuously moving platform

    Science.gov (United States)

    Mazzeo, Brian A.; Larsen, Jacob; McElderry, Joseph; Guthrie, W. Spencer

    2017-02-01

    Impact-echo testing is a non-destructive evaluation technique for determining the presence of defects in reinforced concrete bridge decks based on the acoustic response of the bridge deck when struck by an impactor. In this work, we build on our prior research with a single-channel impactor to demonstrate a seven-channel impact-echo scanning system with independent control of the impactors. This system is towed by a vehicle and integrated with distance measurement for registering the locations of the impacts along a bridge deck. The entire impact and recording system is computer-controlled. Because of a winch system and hinged frame construction of the apparatus, setup, measurement, and take-down of the apparatus can be achieved in a matter of minutes. Signal processing of the impact responses is performed on site and can produce a map of delaminations immediately after data acquisition. This map can then be used to guide other testing and/or can be referenced with the results of other testing techniques to facilitate comprehensive condition assessments of concrete bridge decks. This work demonstrates how impact-echo testing can be performed in a manner that makes complete bridge deck scanning for delaminations rapid and practical.

  4. Effects of Adhesive Connection on Composite Action between FRP Bridge Deck and Steel Girder

    Directory of Open Access Journals (Sweden)

    Xu Jiang

    2017-01-01

    Full Text Available The FRP-steel girder composite bridge system is increasingly used in new constructions of bridges as well as rehabilitation of old bridges. However, the understanding of composite action between FRP decks and steel girders is limited and needs to be systematically investigated. In this paper, depending on the experimental investigations of FRP to steel girder system, the Finite Element (FE models on experiments were developed and analyzed. Comparison between experiments and FE results indicated that the FE models were much stiffer for in-plane shear stiffness of the FRP deck panel. To modify the FE models, rotational spring elements were added between webs and flanges of FRP decks, to simulate the semirigid connections. Numerical analyses were also conducted on four-point bending experiments of FRP-steel composite girders. Good agreement between experimental results and FE analysis was achieved by comparing the load-deflection curves at midspan and contribution of composite action from FRP decks. With the validated FE models, the parametric studies were conducted on adhesively bonded connection between FRP decks and steel girders, which indicated that the loading transfer capacity of adhesive connection was not simply dependent on the shear modulus or thickness of adhesive layer but dominated by the in-plane shear stiffness K.

  5. Comparison of deck- and trial-based approaches to advantageous decision making on the Iowa Gambling Task.

    Science.gov (United States)

    Visagan, Ravindran; Xiang, Ally; Lamar, Melissa

    2012-06-01

    We compared the original deck-based model of advantageous decision making assessed with the Iowa Gambling Task (IGT) with a trial-based approach across behavioral and physiological outcomes in 33 younger adults (15 men, 18 women; 22.2 ± 3.7 years of age). One administration of the IGT with simultaneous measurement of skin conductance responses (SCRs) was performed and the two methods applied: (a) the original approach of subtracting disadvantageous picks of Decks A and B from advantageous picks of Decks C and D and (b) a trial-based approach focused on the financial outcome for each deck leading up to the trial in question. When directly compared, the deck-based approach resulted in a more advantageous behavioral profile than did the trial-based approach. Analysis of SCR data revealed no significant differences between methods for physiological measurements of SCR fluctuations or anticipatory responses to disadvantageous picks. Post hoc investigation of the trial-based method revealed Deck B contributed to both advantageous and disadvantageous decision making for the majority of participants. When divided by blocks of 20, the number of advantageous to disadvantageous choices reversed as the task progressed despite the total number of picks from Deck B remaining high. SCR fluctuations for Deck B, although not significantly different from the other decks, did show a sharp decline after the first block of 20 and remained below levels for Decks C and D toward the end of the task, suggesting that participants may have gained knowledge of the frequency of loss for this deck. (c) 2012 APA, all rights reserved

  6. Ground penetrating radar utilization in exploring inadequate concrete covers in a new bridge deck

    Directory of Open Access Journals (Sweden)

    Md. Istiaque Hasan

    2014-01-01

    Full Text Available The reinforced concrete cast in place four span deck of a concrete bridge near Roanoke, Texas, was recently completed. Due to possible construction errors, it was suspected that the concrete covers in the deck did not conform to drawings and specifications. A full scale non-destructive evaluation of the concrete covers was carried out using ground penetrating radar (GPR equipment. Cover values were determined from the radargram generated from the scan. The estimated covers were plotted on contour maps. Migration data can substitute the drilling based ground truth data without compromising the concrete cover estimations, except for areas with very high cover values. Areas with high water content may result in inaccurate concrete dielectric constants. Based on the results, significant retrofitting of the bridge deck, such as additional overlay, was recommended.

  7. Experimental and Computational Investigation of Triple-rotating Blades in a Mower Deck

    Science.gov (United States)

    Chon, Woochong; Amano, Ryoichi S.

    Experimental and computational studies were performed on the 1.27m wide three-spindle lawn mower deck with side discharge arrangement. Laser Doppler Velocimetry was used to measure the air velocity at 12 different sections under the mower deck. The high-speed video camera test provided valuable visual evidence of airflow and grass discharge patterns. The strain gages were attached at several predetermined locations of the mower blades to measure the strain. In computational fluid dynamics work, computer based analytical studies were performed. During this phase of work, two different trials were attempted. First, two-dimensional blade shapes at several arbitrary radial sections were selected for flow computations around the blade model. Finally, a three-dimensional full deck model was developed and compared with the experimental results.

  8. Super-light SL-Deck elements with fixed end connections

    DEFF Research Database (Denmark)

    Hertz, Kristian Dahl

    2015-01-01

    Super-light structures combining light and strong concrete are invented by the author at the Technical University of Denmark and commercialized by the spin-out company Abeo Ltd. The first product is the SL-Deck element that represents a number of strong improvements to the building industry among...... to low weight and due to possibilities of continuous elements and fixed end connections. A new machine is constructed producing the elements and BIM software is developed optimizing the structures, the production, and the logistics and running the machine. New production lines are established...... building projects leading to considerable savings of time and costs and opening up new possibilities for architects and users. Furthermore, the paper describes full-scale test results with new fixed end connections between decks and walls and between decks and columns in facades giving more possibilities...

  9. Structural Performance Evaluation of Tsing MA Bridge Deck Using Long-Term Monitoring Data

    Science.gov (United States)

    Ni, Y. Q.; Xia, H. W.; Ko, J. M.

    The Tsing Ma Bridge in Hong Kong is suspension bridge with a main span of 1377 m carrying both highway and railway traffic. After completing its construction in 1997, the bridge was instrumented by the Hong Kong SAR Government Highways Department with a long-term structural health monitoring system comprising about 300 sensors permanently installed on the bridge. As part of this monitoring system, a total of 110 strain gauges have been installed to measure strain at the deck cross-sections and bearings. In this study, a method for real-time structural performance evaluation of the stiffening deck system making use of long-term strain measurement data is proposed and verified using the strain monitoring data from a typical deck cross-section of the Tsing Ma Bridge.

  10. STS-27 crew poses for inflight portrait on forward flight deck with football

    Science.gov (United States)

    1988-01-01

    With WILSON NFL football freefloating in front of them, STS-27 astronauts pose on Atlantis', Orbiter Vehicle (OV) 104's, forward flight deck for inflight crew portrait. Crewmembers, wearing blue mission t-shirts, are (left to right) Commander Robert L. Gibson, Mission Specialist (MS) Richard M. Mullane, MS Jerry L. Ross, MS William M. Shepherd, and Pilot Guy S. Gardner. Forward flight deck overhead control panels are visible above crewmembers, commanders and pilots seats in front of them, and forward windows behind them. An auto-set 35mm camera mounted on the aft flight deck was used to take this photo. The football was later presented to the National Football League (NFL) at halftime of the Super Bowl in Miami.

  11. Flow field analysis of a pentagonal-shaped bridge deck by unsteady RANS

    Directory of Open Access Journals (Sweden)

    Md. Naimul Haque

    2016-01-01

    Full Text Available Long-span cable-stayed bridges are susceptible to dynamic wind effects due to their inherent flexibility. The fluid flow around the bridge deck should be well understood for the efficient design of an aerodynamically stable long-span bridge system. In this work, the aerodynamic features of a pentagonal-shaped bridge deck are explored numerically. The analytical results are compared with past experimental work to assess the capability of two-dimensional unsteady RANS simulation for predicting the aerodynamic features of this type of deck. The influence of the bottom plate slope on aerodynamic response and flow features was investigated. By varying the Reynolds number (2 × 104 to 20 × 104 the aerodynamic behavior at high wind speeds is clarified.

  12. Upper Gastrointestinal (GI) Series

    Science.gov (United States)

    ... standard barium upper GI series, which uses only barium a double-contrast upper GI series, which uses both air and ... evenly coat your upper GI tract with the barium. If you are having a double-contrast study, you will swallow gas-forming crystals that ...

  13. 46 CFR 179.350 - Openings in the side of a vessel below the bulkhead or weather deck.

    Science.gov (United States)

    2010-10-01

    ... whether the port light is or is not capable of being opened. (c) Except for engine exhausts, each inlet or... deck. (a) On a vessel operating on exposed or partially protected waters, an opening port light is not permitted below the weather deck unless the sill of the port light is at least 760 millimeters (30 inches...

  14. 49 CFR 214.519 - Floors, decks, stairs, and ladders of on-track roadway maintenance machines.

    Science.gov (United States)

    2010-10-01

    ... roadway maintenance machines. 214.519 Section 214.519 Transportation Other Regulations Relating to... SAFETY On-Track Roadway Maintenance Machines and Hi-Rail Vehicles § 214.519 Floors, decks, stairs, and ladders of on-track roadway maintenance machines. Floors, decks, stairs, and ladders of on-track roadway...

  15. Stress analysis on passenger deck due to modification from passenger ship to vehicle-carrying ship

    Science.gov (United States)

    Zubaydi, A.; Sujiatanti, S. H.; Hariyanto, T. R.

    2018-03-01

    Stress is a basic concept in learning about material mechanism. The main focus that needs to be brought to attention in analyzing stress is strength, which is the structural capacity to carry or distribute loads. The structural capacity not only measured by comparing the maximum stress with the material’s yield strength but also with the permissible stress required by the Indonesian Classification Bureau (BKI), which certainly makes it much safer. This final project analyzes stress in passenger deck that experiences modification due to load changes, from passenger load to vehicle one, carrying: 6-wheels truck with maximum weight of 14 tons, a passenger car with maximum weight of 3.5 tons, and a motorcycle with maximum weight of 0.4 tons. The deck structure is modelled using finite element software. The boundary conditions given to the structural model are fix and simple constraint. The load that works on this deck is the deck load which comes from the vehicles on deck with three vehicles’ arrangement plans. After that, software modelling is conducted for analysis purpose. Analysis result shows a variation of maximum stress that occurs i.e. 135 N/mm2, 133 N/mm2, and 152 N/mm2. Those maximum stresses will not affect the structure of passenger deck’s because the maximum stress that occurs indicates smaller value compared to the Indonesian Classification Bureau’s permissible stress (175 N/mm2) as well as the material’s yield strength (235 N/mm2). Thus, the structural strength of passenger deck is shown to be capable of carrying the weight of vehicles in accordance with the three vehicles’ arrangement plans.

  16. Simple model of cable-stayed bridge deck subjected to static wind loading

    Science.gov (United States)

    Kang, Yi-Lung; Wang, Yang Cheng

    1997-05-01

    Cable-stayed bridges have been known since 18th century with aesthetics design. The structural system and the structural behavior are significantly different from those of continuous bridges. Compared to continuous bridge, cable- stayed bridges have more flexure bridge deck than those of continuous bridges.On the other hand, cable-stayed bridges have less stiffness to resist wind loading especially for lateral loads. The first considering of bridge engineering is safety. In 1940's, Tacoma Narrows Suspension Bridge destroyed by wind loading is a good example even though it is not a cable-stayed bridge. After the bridge was destroyed, a lot of research articles have been published regarding cable supported bridge subjected to wind loading. In recent days, high strength materials have been served. The bridge engineers use the advantages to expand the span length of cable-stayed bridges. Due to the span length increased and the use of high strength materials, cable- stayed bridges have more significant nonlinear behavior subjected to wind loading. In this paper, a slice bridge deck of cable-stayed bridge connected to internal support cables is considered. The deck has been considered to be subjected to lateral static wind loading. Since cables can not take compressive force, the deck has strongly nonlinear behavior even though the materials are linear elastic. Several primary load combinations have ben considered in this paper such as the bridge deck supposed to be moved horizontally without rotation or the bridge deck supposed to be moved horizontally with rotational deformation. The mathematical formulas and the numerical solutions are found and represented in graphical forms. The results can be provided to bridge designers and researchers for further study of this type of structure subjected to wind loading.

  17. Towards a characterization of information automation systems on the flight deck

    Science.gov (United States)

    Dudley, Rachel Feddersen

    This thesis summarizes research to investigate the characteristics that define information automation systems used on aircraft flight decks and the significant impacts that these characteristics have on pilot performance. Major accomplishments of the work include the development of a set of characteristics that describe information automation systems on the flight deck and an experiment designed to study a subset of these characteristics. Information automation systems on the flight deck are responsible for the collection, processing, analysis, and presentation of data to the flightcrew. These systems pose human factors issues and challenges that must be considered by designers of these systems. Based on a previously developed formal definition of information automation for aircraft flight deck systems, an analysis process was developed and conducted to reach a refined set of information automation characteristics. In this work, characteristics are defined as a set of properties or attributes that describe an information automation system's operation or behavior, which can be used to identify and assess potential human factors issues. Hypotheses were formed for a subset of the characteristics: Automation Visibility, Information Quality, and Display Complexity. An experimental investigation was developed to measure performance impacts related to these characteristics, which showed mixed results of expected and surprising findings, with many interactions. A set of recommendations were then developed based on the experimental observations. Ensuring that the right information is presented to pilots at the right time and in the appropriate manner is the job of flight deck system designers. This work provides a foundation for developing recommendations and guidelines specific to information automation on the flight deck with the goal of improving the design and evaluation of information automation systems before they are implemented.

  18. STS-36 Commander Creighton listens to music on OV-104's forward flight deck

    Science.gov (United States)

    1990-01-01

    STS-36 Commander John O. Creighton, smiling and wearing a headset, listens to music as the tape recorder freefloats in front of him. During this lighter moment of the mission, Creighton is positioned at the commanders station on the forward flight deck of Atlantis, Orbiter Vehicle (OV) 104. Forward flight deck windows W1 and W2 appear on his left. Creighton and four other astronauts spent four days, 10 hours and 19 minutes aboard the spacecraft for the Department of Defense (DOD) devoted mission.

  19. STS-31 crewmembers during simulation on the flight deck of JSC's FB-SMS

    Science.gov (United States)

    1988-01-01

    On the flight deck of JSC's fixed based (FB) shuttle mission simulator (SMS), Mission Specialist (MS) Steven A. Hawley (left), on aft flight deck, looks over the shoulders of Commander Loren J. Shriver, seated at the commanders station (left) and Pilot Charles F. Bolden, seated at the pilots station and partially blocked by the seat's headrest (right). The three astronauts recently named to the STS-31 mission aboard Discovery, Orbiter Vehicle (OV) 103, go through a procedures checkout in the FB-SMS. The training simulation took place in JSC's Mission Simulation and Training Facility Bldg 5.

  20. Influence of Pavement on Fatigue Performance of Urban Steel Box Girder Deck

    Directory of Open Access Journals (Sweden)

    Zheng Zhongyue

    2016-01-01

    Full Text Available Based on spatial finite element analysis method, the Influence of pavement on fatigue performance of orthotropic steel deck was analyzed in terms of pavement system, asphalt pavement stiffness. The result shows that compared with asphalt pavement system, RPC pavement system can not only obviously improve the stress condition of steel bridge deck, but also significantly extend the fatigue life of steel bridge panel; Increasing the stiffness of pavement layer can obviously reduce the stress amplitude of fatigue details, especially for direct contact with the pavement.

  1. Flight Deck Display Technologies for 4DT and Surface Equivalent Visual Operations

    Science.gov (United States)

    Prinzel, Lawrence J., III; Jones, Denis R.; Shelton, Kevin J.; Arthur, Jarvis J., III; Bailey, Randall E.; Allamandola, Angela S.; Foyle, David C.; Hooey, Becky L.

    2009-01-01

    NASA research is focused on flight deck display technologies that may significantly enhance situation awareness, enable new operating concepts, and reduce the potential for incidents/accidents for terminal area and surface operations. The display technologies include surface map, head-up, and head-worn displays; 4DT guidance algorithms; synthetic and enhanced vision technologies; and terminal maneuvering area traffic conflict detection and alerting systems. This work is critical to ensure that the flight deck interface technologies and the role of the human participants can support the full realization of the Next Generation Air Transportation System (NextGen) and its novel operating concepts.

  2. Measurement of bridge deck layout prior to concrete placement : final report.

    Science.gov (United States)

    2017-01-01

    The main objective of this research was to develop a method of measuring and : producing as built bridge drawings. This was the first step in the feasibility : assessment for automated bridge deck paving. The research goes to show the : standard meth...

  3. STS-26 crew on fixed based (FB) shuttle mission simulator (SMS) flight deck

    Science.gov (United States)

    1988-01-01

    STS-26 Discovery, Orbiter Vehicle (OV) 103, Commander Frederick H. Hauck (left) and Pilot Richard O. Covey review checklists in their respective stations on the foward flight deck. The STS-26 crew is training in the fixed base (FB) shuttle mission simulator (SMS) located in JSC Mission Simulation and Training Facility Bldg 5.

  4. Research on construction technology for orthotropic steel deck pavement of Haihe River Chunyi Bridge

    Science.gov (United States)

    Xue, Y. C.; Qian, Z. D.; Zhang, M.

    2017-01-01

    In order to ensure the good service quality of orthotropic steel deck pavement of Haihe River Chunyi Bridge in Tianjin, and to reduce the occurrence of pavement diseases like lateral and longitudinal cracks, the key working procedures such as steel deck cleaning, anticorrosive coating, bonding layer spraying, seam cutting, epoxy asphalt concrete’s mixing, transportation, paving and compaction were studied. The study was based on the main features of epoxy asphalt concrete which is the pavement materials of Haihe River Chunyi Bridge, and combined with the basic characteristics and construction conditions of Haihe River Chunyi Bridge. Furthermore, some processing measures like controlling time and temperature, continuous paving with two pavers, lateral feeding, and improving the compaction method were proposed. The project example shows that the processing measures can effectively solve the technical difficulties in the construction of orthotropic steel deck pavement of Haihe River Chunyi Bridge, can greatly improve the construction speed and quality, and can provide reference for the same kinds of orthotropic steel deck pavement construction.

  5. To the question of reliability and durability ballastless deck of bridge

    Directory of Open Access Journals (Sweden)

    V.V. Prystynskaya

    2012-12-01

    Full Text Available The principal causes of operational defects in bridge ballastless deck plates are considered in the article. The drawbacks of these plates construction that prevent from achieving a higher level of bridge framework reliability and durability have been analysed.

  6. A simple analytic treatment of rescattering effects in the Deck model

    International Nuclear Information System (INIS)

    Bowler, M.G.

    1979-01-01

    A simple application of old-fashioned final-state interaction theory is shown to give the result that rescattering the Deck model of diffraction dissociation is well represented by multiplying the bare amplitude by esup(idelta)cosdelta. The physical reasons for this result emerge particularly clearly in this formulation. (author)

  7. Field performance of timber bridges. 5, Little Salmon Creek stress-laminated deck bridge

    Science.gov (United States)

    M. A. Ritter; J. A. Kainz; G. J. Porter

    The Little Salmon Creek bridge was constructed in November 1988 on the Allegheny National Forest in Pennsylvania. The bridge is a simple span, single-lane, stress-laminated deck superstructure that is approximately 26-ft long and 16-ft wide. The bridge is unique in that it is the first known stress-laminated timber bridge to be constructed of hardwood lumber. The...

  8. Fatigue analysis and life prediction of composite highway bridge decks under traffic loading

    Directory of Open Access Journals (Sweden)

    Fernando N. Leitão

    Full Text Available Steel and composite (steel-concrete highway bridges are currently subjected to dynamic actions of variable magnitude due to convoy of vehicles crossing on the deck pavement. These dynamic actions can generate the nucleation of fractures or even their propagation on the bridge deck structure. Proper consideration of all of the aspects mentioned pointed our team to develop an analysis methodology with emphasis to evaluate the stresses through a dynamic analysis of highway bridge decks including the action of vehicles. The design codes recommend the application of the curves S-N associated to the Miner's damage rule to evaluate the fatigue and service life of steel and composite (steel-concrete bridges. In this work, the developed computational model adopted the usual mesh refinement techniques present in finite element method simulations implemented in the ANSYS program. The investigated highway bridge is constituted by four longitudinal composite girders and a concrete deck, spanning 40.0m by 13.5m. The analysis methodology and procedures presented in the design codes were applied to evaluate the fatigue of the bridge determining the service life of the structure. The main conclusions of this investigation focused on alerting structural engineers to the possible distortions, associated to the steel and composite bridge's service life when subjected to vehicle's dynamic actions.

  9. Moving dynamic loads caused by bridge deck joint unevenness - a case study

    CSIR Research Space (South Africa)

    Steyn, WJV

    2004-11-01

    Full Text Available This paper focus on the general guidelines regarding maximum unevenness from bridge deck joints for typical South African heavy vehicles, in order to minimize the generation of moving variable loads. In a recent investigation it was found that areas...

  10. Field performance of timber bridges. 15, Pueblo County, Colorado, stress-laminated deck bridge

    Science.gov (United States)

    L. E. Hislop

    The Pueblo County 204B bridge was constructed in March 1990 in Pueblo, Colorado, as a demonstration bridge under the USDA Forest Service Timber Bridge Initiative. The stress-laminated deck superstructure is approximately 10 m long, 9 m wide, and 406 mm deep, with a skew of 10 degrees. Performance monitoring was conducted for 3 years, beginning at...

  11. Field performance of timber bridges. 7, Connell Lake stress-laminated deck bridge

    Science.gov (United States)

    L. E. Hislop; M. A. Ritter

    The Connell Lake bridge was constructed in early 1991 on the Tongass National Forest, Alaska, as a demonstration bridge under the Timber Bridge Initiative. The bridge is a stress-laminated deck structure with an approximate 36-ft length and 18-ft width and is the first known stress-laminated timber bridge constructed in Alaska. Performance of the bridge was monitored...

  12. Field performance of timber bridges. 6, Hoffman Run stress-laminated deck bridge

    Science.gov (United States)

    M. A. Ritter; P. D. Hilbrich Lee; G. J. Porter

    The Hoffman Run bridge, located just outside Dahoga, Pennsylvania, was constructed in October 1990. The bridge is a simple-span, single-lane, stress-laminated deck superstructure that is approximately 26 ft long and 16 ft wide. It is the second stress-laminated timber bridge to be constructed of hardwood lumber in Pennsylvania. The performance of the bridge was...

  13. NextGen Flight Deck Data Comm : Auxiliary Synthetic Speech Phase II

    Science.gov (United States)

    2015-07-01

    Data Comma text-based controller-pilot communication systemis expected to yield several NextGen safety and efficiency benefits. With Data Comm, communication becomes a visual task, and may potentially increase head-down time on the flight deck ...

  14. Stacked Deck: An Effective, School-Based Program for the Prevention of Problem Gambling

    Science.gov (United States)

    Williams, Robert J.; Wood, Robert T.; Currie, Shawn R.

    2010-01-01

    School-based prevention programs are an important component of problem gambling prevention, but empirically effective programs are lacking. Stacked Deck is a set of 5-6 interactive lessons that teach about the history of gambling; the true odds and "house edge"; gambling fallacies; signs, risk factors, and causes of problem gambling; and…

  15. 14 CFR 121.550 - Secret Service Agents: Admission to flight deck.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Secret Service Agents: Admission to flight... OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Flight Operations § 121.550 Secret Service Agents: Admission to flight deck. Whenever an Agent of the Secret Service who is assigned the duty...

  16. Mechanical and chemical properties of CCA-treated lumber removed from spent residential decks

    Science.gov (United States)

    Robert L. Smith; David Bailey; Philip A. Araman

    2007-01-01

    The amount of chromated copper arsenate (CCA)- treated wood being removed from spent residential decks is increasing at a tremendous rate. While most spent CCA-treated wood is being disposed in landfills, further useful and environmentally beneficial alternatives have to be met. If the volume of CCA-treated wood reaching landfills continues to rise, stricter disposal...

  17. Load test of the 277W Building high bay roof deck and support structure

    International Nuclear Information System (INIS)

    McCoy, R.M.

    1994-01-01

    The 277W Building high bay roof area was load tested according to the approved load-test procedure, WHC-SD-GN-TP-30015, Revision 1. The 277W Building is located in the 200 West Area of the Hanford Site and has the following characteristics: roof deck -- wood decking supported by 4 x 14 timber purlins; roof membrane -- tar and gravel; roof slope -- flat (<10 deg); and roof elevation -- maximum height of about 63 ft. The 227W Building was visited in March 1994 for a visual inspection. During this inspection, cracked areas were visible in the decking, but it was not possible to determine whether these cracks extended completely through the decking, which is 2-in. thick. The building was revisited in March 1994 for the purpose of writing this test report. Because the roof requires personnel access, a test was determined to be the best way to qualify the roof. The conclusions are that the roof has been qualified for 500-lb total roof load and that the ''No Roof Access'' signs can be changed to ''Roof Access Restricted'' signs

  18. Evaluation of performance and maximum length of continuous decks in bridges : part 1.

    Science.gov (United States)

    2011-06-01

    The purpose of this research was to evaluate the performance history of continuous bridge decks in the State of Georgia, to determine why the current design detail works, to recommend a new design detail, and to recommend the maximum and/or optimum l...

  19. Effects of Adhesive Connection on Composite Action between FRP Bridge Deck and Steel Girder

    NARCIS (Netherlands)

    Jiang, X.; Luo, Chengwei; Qiang, X.; Kolstein, M.H.; Bijlaard, F.S.K.

    2017-01-01

    The FRP-steel girder composite bridge system is increasingly used in new constructions of bridges as well as rehabilitation of old bridges. However, the understanding of composite action between FRP decks and steel girders is limited and needs to be systematically investigated. In this paper,

  20. STS 51-L crewmembers during training session in flight deck simulation

    Science.gov (United States)

    1985-01-01

    S85-46207 (December 1985) --- Shuttle Mission Simulator (SMS) scene of astronauts Michael J. Smith, Ellison S. Onizuka, Judith A. Resnik, and Francis R. (Dick) Scobee in their launch and entry positions on the flight deck. The photo was taken by Bill Bowers.

  1. Live load distribution on longitudinal glued-laminated timber deck bridges : final report : conclusions and recommendations

    Science.gov (United States)

    Fouad Fanous; Jeremy May; Terry Wipf; Michael Ritter

    2010-01-01

    Over the past few years the United States Department of Agriculture (USDA), Forest Products Laboratory (FPL), and the Federal Highway Administration (FHWA) have supported several research programs. This paper is a result of a study sponsored by FPL, with the objective of determining how truckloads are distributed to the deck panels of a longitudinal glued-laminated...

  2. Two-course bonded concrete bridge deck construction : condition and performance after six years.

    Science.gov (United States)

    1981-01-01

    This report presents the findings from a six-year study of two-course bonded concrete bridge decks constructed in Virginia. Each of three special portland cement concretes was applied as an overlay, or wearing course, on two experimental spans. The o...

  3. Plans for crash-tested wood bridge railings for concrete decks

    Science.gov (United States)

    Michael A. Ritter; Ronald K. Faller; Barry T. Rosson; Paula D. Hilbrich Lee; Sheila Rimal. Duwadi

    1998-01-01

    As part of a continuing cooperative research between the Midwest Roadside Safety Facility (MwRSF); the USDA Forest Service, Forest Products Laboratory (FPL); and the Federal Highway Administration (FHWA), several crashworthy wood bridge railings and approach railing transitions have been adapted for use on concrete bridge decks. These railings meet testing and...

  4. Bridge deck cracking : effects on in-service performance, prevention, and remediation.

    Science.gov (United States)

    2015-08-01

    The main objectives of this project were: (a) to identify the causes of early-age cracking in concrete bridge decks, (b) to provide : recommendations for effective mitigation of early-age cracking, (c) to assess the effect of cracks on the long-term ...

  5. Numerical investigation of the bearing capacity of transversely prestressed concrete deck slabs

    NARCIS (Netherlands)

    Amir, S.; Van der Veen, C.; Walraven, J.C.; De Boer, A.

    2014-01-01

    The research subject of this paper is the bearing capacity of transversely prestressed concrete bridge decks between concrete girders under concentrated loads. Experiments on a 1:2 scale model of this bridge were carried out in the laboratory and a 3D nonlinear finite element model was developed in

  6. Effectiveness of polymer bridge deck overlays in highway noise reduction : technical paper.

    Science.gov (United States)

    2016-04-01

    The Kansas Department of Transportation (KDOT) began placing multi-layer polymer bridge deck overlays in 1999 and at the present time have over 200 in service. A few years after placing the overlays, individuals indicated that they noticed how quiet ...

  7. A Country Discovered: Upper Juniors Explore Meanings in "Hamlet."

    Science.gov (United States)

    Carter, Dennis

    1989-01-01

    Describes a project in England in which a class of 9- to 11-year olds enthusiastically and successfully explored the play "Hamlet" by writing about, discussing, performing, and visually interpreting the actual text. The teacher suggests that, with a little creativity, Shakespeare is very accessible to children. (SM)

  8. Study of the action of blast deck charge in rocky soils

    Directory of Open Access Journals (Sweden)

    Boiko V.V.

    2017-04-01

    Full Text Available Blasting (B in the industry, including the mining extraction of minerals, are carried out mostly with the use of blasthole charges that systematically distributed on the block that is undermined, by individual groups. The latter are blasted according to the scheme of short-delay firing (SDF through the intervals that are accepted not less than 20 Ms. Thus, the seismic effect of group charge explosion, consisting of individual blasthole charges and that actually is a group located charge determined by the formula of concentrated charge. Blast deck charges are effectively used in the driving of the trenches in the mining, formation of screens and cracks near the security objects. Only this method of performing blasting allows to define seismic effect in the transition from one diameter of a charge to another, as well as to determine the actual number of detonated charges in one group, which may differ from the calculated in drilling and blasting project. The work analyzes the physical essence of processes happened while blasting of blast deck charges. The effect of the orientation of the seismic action of blasting of blast deck charges towards the allocation line of charges is investigated. The results of generalized dependence of the speed of the displacement of the ground by the blast parameters and epicentral distance are obtained. We demonstrate with specific examples that blast deck charges that blasting simultaneously make a major chain of the career massive explosions at mining. Keywords: seismic fluctuations; the number of charges; the interaction of charges; the distance between the charges; the coefficients of the seismicity and the attenuation of the intensity of the waves; the unit charge; blast deck and blasthole charges; phase shifting; effective charge.

  9. Taming Liquid Hydrogen: The Centaur Upper Stage Rocket

    Science.gov (United States)

    Dawson, Virginia P.; Bowles, Mark D.

    2004-01-01

    The Centaur is one of the most powerful rockets in the world. As an upper-stage rocket for the Atlas and Titan boosters it has been a reliable workhorse for NASA for over forty years and has played an essential role in many of NASA's adventures into space. In this CD-ROM you will be able to explore the Centaur's history in various rooms to this virtual museum. Visit the "Movie Theater" to enjoy several video documentaries on the Centaur. Enter the "Interview Booth" to hear and read interviews with scientists and engineers closely responsible for building and operating the rocket. Go to the "Photo Gallery" to look at numerous photos of the rocket throughout its history. Wander into the "Centaur Library" to read various primary documents of the Centaur program. Finally, stop by the "Observation Deck" to watch a virtual Centaur in flight.

  10. Nonvariceal upper gastrointestinal bleeding

    International Nuclear Information System (INIS)

    Burke, Stephen J.; Weldon, Derik; Sun, Shiliang; Golzarian, Jafar

    2007-01-01

    Nonvariceal upper gastrointestinal bleeding (NUGB) remains a major medical problem even after advances in medical therapy with gastric acid suppression and cyclooxygenase (COX-2) inhibitors. Although the incidence of upper gastrointestinal bleeding presenting to the emergency room has slightly decreased, similar decreases in overall mortality and rebleeding rate have not been experienced over the last few decades. Many causes of upper gastrointestinal bleeding have been identified and will be reviewed. Endoscopic, radiographic and angiographic modalities continue to form the basis of the diagnosis of upper gastrointestinal bleeding with new research in the field of CT angiography to diagnose gastrointestinal bleeding. Endoscopic and angiographic treatment modalities will be highlighted, emphasizing a multi-modality treatment plan for upper gastrointestinal bleeding. (orig.)

  11. Nonvariceal upper gastrointestinal bleeding

    Energy Technology Data Exchange (ETDEWEB)

    Burke, Stephen J.; Weldon, Derik; Sun, Shiliang [University of Iowa, Department of Radiology, Iowa, IA (United States); Golzarian, Jafar [University of Iowa, Department of Radiology, Iowa, IA (United States); University of Iowa, Department of Radiology, Carver College of Medicine, Iowa, IA (United States)

    2007-07-15

    Nonvariceal upper gastrointestinal bleeding (NUGB) remains a major medical problem even after advances in medical therapy with gastric acid suppression and cyclooxygenase (COX-2) inhibitors. Although the incidence of upper gastrointestinal bleeding presenting to the emergency room has slightly decreased, similar decreases in overall mortality and rebleeding rate have not been experienced over the last few decades. Many causes of upper gastrointestinal bleeding have been identified and will be reviewed. Endoscopic, radiographic and angiographic modalities continue to form the basis of the diagnosis of upper gastrointestinal bleeding with new research in the field of CT angiography to diagnose gastrointestinal bleeding. Endoscopic and angiographic treatment modalities will be highlighted, emphasizing a multi-modality treatment plan for upper gastrointestinal bleeding. (orig.)

  12. Algorithms for highway-speed acoustic impact-echo evaluation of concrete bridge decks

    Science.gov (United States)

    Mazzeo, Brian A.; Guthrie, W. Spencer

    2018-04-01

    A new acoustic impact-echo testing device has been developed for detecting and mapping delaminations in concrete bridge decks at highway speeds. The apparatus produces nearly continuous acoustic excitation of concrete bridge decks through rolling mats of chains that are placed around six wheels mounted to a hinged trailer. The wheels approximately span the width of a traffic lane, and the ability to remotely lower and raise the apparatus using a winch system allows continuous data collection without stationary traffic control or exposure of personnel to traffic. Microphones near the wheels are used to record the acoustic response of the bridge deck during testing. In conjunction with the development of this new apparatus, advances in the algorithms required for data analysis were needed. This paper describes the general framework of the algorithms developed for converting differential global positioning system data and multi-channel audio data into maps that can be used in support of engineering decisions about bridge deck maintenance, rehabilitation, and replacement (MR&R). Acquisition of position and audio data is coordinated on a laptop computer through a custom graphical user interface. All of the streams of data are synchronized with the universal computer time so that audio data can be associated with interpolated position information through data post-processing. The audio segments are individually processed according to particular detection algorithms that can adapt to variations in microphone sensitivity or particular chain excitations. Features that are greater than a predetermined threshold, which is held constant throughout the analysis, are then subjected to further analysis and included in a map that shows the results of the testing. Maps of data collected on a bridge deck using the new acoustic impact-echo testing device at different speeds ranging from approximately 10 km/h to 55 km/h indicate that the collected data are reasonably repeatable. Use

  13. Numerical simulations and experimental measurements of steel and ice impacts on concrete for acoustic interrogation of delaminations in bridge decks

    Energy Technology Data Exchange (ETDEWEB)

    Mazzeo, Brian A.; Patil, Anjali N.; Klis, Jeffrey M. [Brigham Young University, Department of Electrical and Computer Engineering, Provo, Utah, 84602 (United States); Hurd, Randy C.; Truscott, Tadd T. [Brigham Young University, Department of Mechanical Engineering, Provo, Utah, 84602 (United States); Guthrie, W. Spencer [Brigham Young University, Department of Civil and Environmental Engineering, Provo, Utah, 84602 (United States)

    2014-02-18

    Delaminations in bridge decks typically result from corrosion of the top mat of reinforcing steel, which leads to a localized separation of the concrete cover from the underlying concrete. Because delaminations cannot be detected using visual inspection, rapid, large-area interrogation methods are desired to characterize bridge decks without disruption to traffic, without the subjectivity inherent in existing methods, and with increased inspector safety. To this end, disposable impactors such as water droplets or ice chips can be dropped using automatic dispensers onto concrete surfaces to excite mechanical vibrations while acoustic responses can be recorded using air-coupled microphones. In this work, numerical simulations are used to characterize the flexural response of a model concrete bridge deck subject to both steel and ice impactors, and the results are compared with similar experiments performed in the laboratory on a partially delaminated concrete bridge deck slab. The simulations offer greater understanding of the kinetics of impacts and the responses of materials.

  14. Evaluation of bridge decks using non-destructive evaluation (NDE) at near highway speeds for effective asset management - pilot project.

    Science.gov (United States)

    2016-09-29

    This project piloted the findings from an initial research and development project pertaining to the detection, : quantification, and visualization of bridge deck distresses through the use of remote sensing techniques, specifically : combining optic...

  15. Flight deck human factors issues for National Airspace System (NAS) en route controller pilot data link communications (CPDLC)

    Science.gov (United States)

    2017-05-01

    Fundamental differences exist between transmissions of Air Traffic Control clearances over voice and those transmitted via Controller Pilot Data Link Communications (CPDLC). This paper provides flight deck human factors issues that apply to processin...

  16. Environmental Durability of Reinforced Concrete Deck Girders Strengthened for Shear with Surface-Bonded Carbon Fiber-Reinforced Polymer

    Science.gov (United States)

    2009-05-01

    "This research investigated the durability of carbon fiber-reinforced polymer composites (CFRP) used for shear strengthening reinforced concrete deck girders. Large beams were used to avoid accounting for size effects in the data analysis. The effort...

  17. Human factors considerations in the design and evaluation of flight deck displays and controls : version 2.0

    Science.gov (United States)

    2016-12-01

    The objective of this effort is to have a single source reference document for human factors regulatory and guidance material for flight deck displays and controls, in the interest of improving aviation safety. This document identifies guidance on hu...

  18. Development and validation of deterioration models for concrete bridge decks - phase 1 : artificial intelligence models and bridge management system.

    Science.gov (United States)

    2013-06-01

    This research documents the development and evaluation of artificial neural network (ANN) models to predict the condition ratings of concrete highway bridge decks in Michigan. Historical condition assessments chronicled in the national bridge invento...

  19. Development and validation of deterioration models for concrete bridge decks - phase 2 : mechanics-based degradation models.

    Science.gov (United States)

    2013-06-01

    This report summarizes a research project aimed at developing degradation models for bridge decks in the state of Michigan based on durability mechanics. A probabilistic framework to implement local-level mechanistic-based models for predicting the c...

  20. The 100 kV Faraday cage (High Voltage Deck) for the SPIDER experiment

    International Nuclear Information System (INIS)

    Boldrin, Marco; Grando, Luca; Pesce, Alberto; Recchia, Mauro; Toigo, Vanni; Gutierrez, Daniel; Simon, Muriel; Faoro, Giovanni; Guion, Andrea; Maggiora, Edoardo; Pedron, Diego; Roman, Anita; Decamps, Hans

    2015-01-01

    Highlights: • A 100 keV experiment is under construction to optimize ITER NBI Ion Source. • The Ion Source Power Supplies are hosted inside a wide −100 kVdc Faraday cage (HVD). • The paper reports on the design solutions of the HVD. • Electrostatic and electromagnetic analyses are presented. • Procurement activities status is reported. - Abstract: In order to optimize the design and operation of the Ion Source for the ITER Neutral Beam Injector (NBI), a dedicated 100 keV Ion Source, identified as Source for the Production of Ions of Deuterium Extracted from RF plasma (SPIDER), is under construction in the Neutral Beam Test Facility, at the Consorzio RFX premises, in Padua, Italy. The Ion Source, polarized at −112 kVdc voltage, will produce negative ions (Deuterium D"− or Hydrogen H"−) which, extracted from the Plasma Grid with an extraction voltage up to 12 keV, are accelerated up to 100 keV by the 100 kVdc Power Supply (100 kV PS). The required Ion Source and the Extraction Power Supplies (ISEPS) system and the associated diagnostics are hosted inside a High Voltage Deck (HVD), a −100 kVdc air-insulated Faraday cage. These power supplies and various diagnostics and control equipment are connected to the Ion Source by means of a High Voltage Transmission Line (TL). The HVD (procurement started mid 2013; delivery on site in the second half of 2014) will consist of a wide structure (13 m (L) × 11 m (W) × 5 m (H)), designed to support the weight of the ISEPS components, mounted on supporting insulators and clad with a conductive metal sheet in order to reduce the electromagnetic interference (EMI). The paper reports on the design solutions of the HVD focusing on insulation, mechanical, thermal and EMI issues. The details of the main HVD interfaces with the TL and with insulating transformer are also described. Finite Element (FE) analyses have been performed, on the one hand, to verify the configuration from the electrostatic point of view and

  1. The 100 kV Faraday cage (High Voltage Deck) for the SPIDER experiment

    Energy Technology Data Exchange (ETDEWEB)

    Boldrin, Marco, E-mail: marco.boldrin@igi.cnr.it [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete S.p.A.), Corso Stati Uniti 4, 35127 Padova (Italy); Grando, Luca; Pesce, Alberto; Recchia, Mauro; Toigo, Vanni [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete S.p.A.), Corso Stati Uniti 4, 35127 Padova (Italy); Gutierrez, Daniel; Simon, Muriel [Fusion for Energy, c/o Josep Pla 2, 08019 Barcelona (Spain); Faoro, Giovanni; Guion, Andrea; Maggiora, Edoardo; Pedron, Diego [COELME – Costruzioni Elettromeccaniche S.p.A., via G. Galilei no. 1/2, 30036 S. Maria di Sala, Venezia (Italy); Roman, Anita [Studio di Ingegneria RS s.r.l., Viale dell’Arcella 1, 35153 Padova (Italy); Decamps, Hans [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France)

    2015-10-15

    Highlights: • A 100 keV experiment is under construction to optimize ITER NBI Ion Source. • The Ion Source Power Supplies are hosted inside a wide −100 kVdc Faraday cage (HVD). • The paper reports on the design solutions of the HVD. • Electrostatic and electromagnetic analyses are presented. • Procurement activities status is reported. - Abstract: In order to optimize the design and operation of the Ion Source for the ITER Neutral Beam Injector (NBI), a dedicated 100 keV Ion Source, identified as Source for the Production of Ions of Deuterium Extracted from RF plasma (SPIDER), is under construction in the Neutral Beam Test Facility, at the Consorzio RFX premises, in Padua, Italy. The Ion Source, polarized at −112 kVdc voltage, will produce negative ions (Deuterium D{sup −} or Hydrogen H{sup −}) which, extracted from the Plasma Grid with an extraction voltage up to 12 keV, are accelerated up to 100 keV by the 100 kVdc Power Supply (100 kV PS). The required Ion Source and the Extraction Power Supplies (ISEPS) system and the associated diagnostics are hosted inside a High Voltage Deck (HVD), a −100 kVdc air-insulated Faraday cage. These power supplies and various diagnostics and control equipment are connected to the Ion Source by means of a High Voltage Transmission Line (TL). The HVD (procurement started mid 2013; delivery on site in the second half of 2014) will consist of a wide structure (13 m (L) × 11 m (W) × 5 m (H)), designed to support the weight of the ISEPS components, mounted on supporting insulators and clad with a conductive metal sheet in order to reduce the electromagnetic interference (EMI). The paper reports on the design solutions of the HVD focusing on insulation, mechanical, thermal and EMI issues. The details of the main HVD interfaces with the TL and with insulating transformer are also described. Finite Element (FE) analyses have been performed, on the one hand, to verify the configuration from the electrostatic point of

  2. Semiempirical Methodology for Estimating the Service Life of Concrete Deck Panels Strengthened with Fiber-Reinforced Polymer

    Directory of Open Access Journals (Sweden)

    Eon-Kyoung Kim

    2014-01-01

    Full Text Available Deterioration of concrete bridge decks affects their durability, safety, and function. It is therefore necessary to conduct structural rehabilitation of damaged concrete decks by strengthening them with fiber-reinforced polymer. Of the recent studies on the strengthened structures, most have focused on static behavior; only a few studies have investigated fatigue behavior. Accurate analysis of fatigue in concrete deck performance requires a more realistic simulated moving load. This study developed a theoretical live-load model to reflect the effect of moving vehicle loads, based on a statistical approach to the measurement of real traffic loads over various time periods in Korea. It assessed the fatigue life and strengthening effect of bridge decks strengthened with either carbon fiber sheets or grid carbon fiber polymer plastic using probabilistic and reliability analyses. It used extrapolations and simulations to derive maximum load effects for time periods ranging from 1 day to 75 years. Limited fatigue tests were conducted and probabilistic and reliability analyses were carried out on the strengthened concrete bridge deck specimens to predict the extended fatigue life. Analysis results indicated that strengthened concrete decks provide sufficient resistance against increasing truck loads during the service life of a bridge.

  3. Stress Regression Analysis of Asphalt Concrete Deck Pavement Based on Orthogonal Experimental Design and Interlayer Contact

    Science.gov (United States)

    Wang, Xuntao; Feng, Jianhu; Wang, Hu; Hong, Shidi; Zheng, Supei

    2018-03-01

    A three-dimensional finite element box girder bridge and its asphalt concrete deck pavement were established by ANSYS software, and the interlayer bonding condition of asphalt concrete deck pavement was assumed to be contact bonding condition. Orthogonal experimental design is used to arrange the testing plans of material parameters, and an evaluation of the effect of different material parameters in the mechanical response of asphalt concrete surface layer was conducted by multiple linear regression model and using the results from the finite element analysis. Results indicated that stress regression equations can well predict the stress of the asphalt concrete surface layer, and elastic modulus of waterproof layer has a significant influence on stress values of asphalt concrete surface layer.

  4. An Advanced Coupled Genetic Algorithm for Identifying Unknown Moving Loads on Bridge Decks

    Directory of Open Access Journals (Sweden)

    Sang-Youl Lee

    2014-01-01

    Full Text Available This study deals with an inverse method to identify moving loads on bridge decks using the finite element method (FEM and a coupled genetic algorithm (c-GA. We developed the inverse technique using a coupled genetic algorithm that can make global solution searches possible as opposed to classical gradient-based optimization techniques. The technique described in this paper allows us to not only detect the weight of moving vehicles but also find their moving velocities. To demonstrate the feasibility of the method, the algorithm is applied to a bridge deck model with beam elements. In addition, 1D and 3D finite element models are simulated to study the influence of measurement errors and model uncertainty between numerical and real structures. The results demonstrate the excellence of the method from the standpoints of computation efficiency and avoidance of premature convergence.

  5. An alternative randomized response model using two deck of cards: a rejoinder

    Directory of Open Access Journals (Sweden)

    Raghunath Arnab

    2014-10-01

    Full Text Available The Randomized response (RR technique with two decks of cards proposed by Odumade and Singh (2009 can always be made more efficient than the RR techniques proposed by Warner (1965, Mangat and Singh (1990, and Mangat (1994 by adjusting the proportion of cards in the decks. Abdelfatah et al. (2011 modified Odumade and Singh (2009 RR technique and claimed that their method can be more efficient than the Warner (1965 model. In this paper it is shown that such claim is not valid and the RR technique proposed by Abdelfatah et al. (2011 is in fact less efficient than the Warner (1965 technique at equal protection of respondents. Such finding are recently shown by Giordano and Perri (2011.

  6. Human engineering analysis for the high speed civil transport flight deck

    Science.gov (United States)

    Regal, David M.; Alter, Keith W.

    1993-01-01

    The Boeing Company is investigating the feasibility of building a second generation supersonic transport. If current studies support its viability, this airplane, known as the High Speed Civil Transport (HSCT), could be launched early in the next century. The HSCT will cruise at Mach 2.4, be over 300 feet long, have an initial range of between 5000 and 6000 NM, and carry approximately 300 passengers. We are presently involved in developing an advanced flight deck for the HSCT. As part of this effort we are undertaking a human engineering analysis that involves a top-down, mission driven approach that will allow a systematic determination of flight deck functional and information requirements. The present paper describes this work.

  7. Upper respiratory tract (image)

    Science.gov (United States)

    The major passages and structures of the upper respiratory tract include the nose or nostrils, nasal cavity, mouth, throat (pharynx), and voice box (larynx). The respiratory system is lined with a mucous membrane that ...

  8. ACA Federal Upper Limits

    Data.gov (United States)

    U.S. Department of Health & Human Services — Affordable Care Act Federal Upper Limits (FUL) based on the weighted average of the most recently reported monthly average manufacturer price (AMP) for...

  9. Upper gastrointestinal bleeding.

    Science.gov (United States)

    Feinman, Marcie; Haut, Elliott R

    2014-02-01

    Upper gastrointestinal (GI) bleeding remains a commonly encountered diagnosis for acute care surgeons. Initial stabilization and resuscitation of patients is imperative. Stable patients can have initiation of medical therapy and localization of the bleeding, whereas persistently unstable patients require emergent endoscopic or operative intervention. Minimally invasive techniques have surpassed surgery as the treatment of choice for most upper GI bleeding. Copyright © 2014 Elsevier Inc. All rights reserved.

  10. Structural maintenance planning based on historical data of corroded deck plates of tankers

    International Nuclear Information System (INIS)

    Garbatov, Y.; Guedes Soares, C.

    2009-01-01

    A probabilistic maintenance and repair analysis of tanker deck plates subjected to general corrosion is presented. The decisions about when to perform maintenance and repair on the structure are studied. Different practical scenarios are analyzed and optimum repair times are proposed. The optimum repair age and intervals are defined based on the statistical analysis of operational data using the Weibull model and some assumptions about the inspection and time needed for repair. The total cost is calculated in normalized form.

  11. Field performance of timber bridges. 9, Big Erick`s stress-laminated deck bridge

    Science.gov (United States)

    J. A. Kainz; J. P. Wacker; M. Nelson

    The Big Erickas bridge was constructed during September 1992 in Baraga County, Michigan. The bridge is 72 ft long, 16 ft wide, and consists of three simple spans: two stress-laminated deck approach spans and a stress-laminated box center span. The bridge is unique in that it is one of the first known stress-laminated timber bridge applications to use Eastern Hemlock...

  12. Field performance of timber bridges. 17, Ciphers stress-laminated deck bridge

    Science.gov (United States)

    James P. Wacker; James A. Kainz; Michael A. Ritter

    In September 1989, the Ciphers bridge was constructed within the Beltrami Island State Forest in Roseau County, Minnesota. The bridge superstructure is a two-span continuous stress-laminated deck that is approximately 12.19 m long, 5.49 m wide, and 305 mm deep (40 ft long, 18 ft wide, and 12 in. deep). The bridge is one of the first to utilize red pine sawn lumber for...

  13. Field performance of timber bridges. 10, Sanborn Brook stress-laminated deck bridge

    Science.gov (United States)

    P. D. Hilbrich Lee; J. P. Wacker; M. A. Ritter

    The Sanborn Brook bridge was constructed in August 1991, 10 miles northeast of Concord, New Hampshire, as part of the demonstration timber bridge program of the USDA Forest Service. The bridge is a simple-span, double-lane, stress-laminated deck superstructure constructed from Southern Pine lumber and is approximately 25 ft long and 28 ft wide with a skew of 14 degrees...

  14. STS-46 'blue' shift crewmembers look up from work on OV-104's flight deck

    Science.gov (United States)

    1992-01-01

    STS-46 'blue' shift crewmembers look up from checklist procedures to have their picture taken on the forward flight deck of Atlantis, Orbiter Vehicle (OV) 104. Seated at the commanders station (left) is Pilot Andrew M. Allen with Italian Payload Specialist Franco Malerba positioned in front of the center console and European Space Agency (ESA) Mission Specialist seated at the pilots station (right). MS Marsha S. Ivins is in the interdeck access hatch at the right bottom corner of the photo.

  15. Choice Experiment Analysis of Outdoor Decking Material Selection in E-Commerce Market in Finland

    OpenAIRE

    Holopainen, Jani Markus; Toppinen, Anne Maarit Kristiina; Lähtinen, Katja Päivikki; Rekola, Mika Olavi

    2017-01-01

    Since the early 1990s, there has been hope that the uptake of certified forest products would ensure more sustainable forest management and also deliver business benefits along the value chain. Our study applies a Discrete Choice Experiment (DCE) to model an e-commerce purchase in the case of multiple products with various attribute and certification combinations in the Finnish retail outdoor decking material market. We received 2772 responses from 231 participants in an online survey. Applyi...

  16. Long-term behaviour of a steel-concrete composite railway bridge deck

    OpenAIRE

    STAQUET, S; TAILHAN, JL; ESPION, B

    2005-01-01

    A prefabricated, composite and prestressed railway bridge deck has been instrumented in June 2000 with strain gages and vibrating wire extensometers. The purpose of this paper is to report on the comparison between strains recorded in situ up to four years with values computed within the framework of an original time-dependent analysis base on the evolution of the degree of hydration and the internal relative humidity in concrete. These fundamental parameters used in the proposed model to com...

  17. Modelling and fatigue life assessment of orthotropic bridge deck details using FEM

    Czech Academy of Sciences Publication Activity Database

    Aygül, M.; AL-Emrani, M.; Urushadze, Shota

    2012-01-01

    Roč. 40, July (2012), s. 129-142 ISSN 0142-1123 R&D Projects: GA MŠk(CZ) 7E08098 Grant - others:evropská komise(XE) RFSR-CT-2008-00033 (BRIFAG) Institutional support: RVO:68378297 Keywords : orthotropic bridge deck * open ribs * structural hot spot stress * effective notch stress Subject RIV: JM - Building Engineering Impact factor: 1.976, year: 2012

  18. Load test of the 272E Building high bay roof deck and support structure

    International Nuclear Information System (INIS)

    McCoy, R.M.

    1994-01-01

    The 272E Building high bay roof area was load tested according to the approved load-test procedure. The 272E Building is located in the 200 East Area of the Hanford Site and has the following characteristics: Roof deck -- wood decking supported by 4 x 14 timber purlins; Roof membrane -- tar and gravel; Roof slope -- flat (<10 deg); and Roof elevation -- maximum height of about 63 ft. The 272 Building was visited in August 1992 for a visual inspection. During this inspection, cracked areas were visible in the decking, but it was not possible to determine whether these cracks extended completely through the decking, which is 2-in. thick. The building was revisited in March 1994 for the purpose of writing this test report. Because the roof requires personnel access, a test was determine to be the best way to qualify the roof. The pre-test briefing consisted of filling out the pre-test checklist, discussing proper lifting techniques, reviewing the fall-protection plan, reviewing the job hazards analysis, and reviewing the robot travel path. The load-test results consist of visual observations and the test engineer's conclusions. Visual observations found no adverse conditions such as large deflections or permanent deformations. No deflection measurements were recorded because the tar and gravel on roof get displaced by the robot tracks; the result is large variations in deflection measurements. The conclusions are that the roof has been qualified for 500-lb total roof load and that the ''No Roof Access'' signs can be changed to ''Roof Access Restricted'' signs

  19. Experimental Analysis of Stiffness of the Riveted Steel Railway Bridge Deck Members’ Joints

    Directory of Open Access Journals (Sweden)

    Gocál Jozef

    2014-12-01

    Full Text Available The paper deals with the real behaviour of the riveted steel railway bridge deck members’ connections with respect to their bending stiffness. Attention is paid to the stringer-to-cross beam connection as well as the cross beam-to-main girder connection. The stiffness of the two connections is investigated on the basis of evaluation of the experimentally determined stress response of the observed structural members to the actual traffic load on an existing railway bridge.

  20. Nondestructive Evaluation of Concrete Bridge Decks with Automated Acoustic Scanning System and Ground Penetrating Radar.

    Science.gov (United States)

    Sun, Hongbin; Pashoutani, Sepehr; Zhu, Jinying

    2018-06-16

    Delamanintions and reinforcement corrosion are two common problems in concrete bridge decks. No single nondestructive testing method (NDT) is able to provide comprehensive characterization of these defects. In this work, two NDT methods, acoustic scanning and Ground Penetrating Radar (GPR), were used to image a straight concrete bridge deck and a curved intersection ramp bridge. An acoustic scanning system has been developed for rapid delamination mapping. The system consists of metal-ball excitation sources, air-coupled sensors, and a GPS positioning system. The acoustic scanning results are presented as a two-dimensional image that is based on the energy map in the frequency range of 0.5⁻5 kHz. The GPR scanning results are expressed as the GPR signal attenuation map to characterize concrete deterioration and reinforcement corrosion. Signal processing algorithms for both methods are discussed. Delamination maps from the acoustic scanning are compared with deterioration maps from the GPR scanning on both bridges. The results demonstrate that combining the acoustic and GPR scanning results will provide a complementary and comprehensive evaluation of concrete bridge decks.

  1. Thermal analysis of GFRP-reinforced continuous concrete decks subjected to top fire

    Science.gov (United States)

    Hawileh, Rami A.; Rasheed, Hayder A.

    2017-12-01

    This paper presents a numerical study that investigates the behavior of continuous concrete decks doubly reinforced with top and bottom glass fiber reinforced polymer (GFRP) bars subjected to top surface fire. A finite element (FE) model is developed and a detailed transient thermal analysis is performed on a continuous concrete bridge deck under the effect of various fire curves. A parametric study is performed to examine the top cover thickness and the critical fire exposure curve needed to fully degrade the top GFRP bars while achieving certain fire ratings for the deck considered. Accordingly, design tables are prepared for each fire curve to guide the engineer to properly size the top concrete cover and maintain the temperature in the GFRP bars below critical design values in order to control the full top GFRP degradation. It is notable to indicate that degradation of top GFRP bars do not pose a collapse hazard but rather a serviceability concern since cracks in the negative moment region widen resulting in simply supported spans.

  2. Upper GI Bleeding in Children

    Science.gov (United States)

    Upper GI Bleeding in Children What is upper GI Bleeding? Irritation and ulcers of the lining of the esophagus, stomach or duodenum can result in upper GI bleeding. When this occurs the child may vomit blood ...

  3. Ash-Based Building Panels Production and Demonstration of Aerock Decking Building Product

    International Nuclear Information System (INIS)

    Alan E. Bland; Jesse Newcomer

    2007-01-01

    trials showed green product sagging, as a result of the die design. After the third die was acquired and fitted to the extruder, satisfactory decking and structural panels were produced. Cured decking was shipped to the US but experienced significant breakage and damage during transport. Subsequent evaluations concluded that an alternative die design was needed that would produce a more robust product resistant to damage. In summary, AeRock Decking can be a commercially-viable non-wood alternative decking product. This project has provided WRI and AeRock the knowledge and understanding to make AeRock Decking a commercial success. However, a commercial demonstration that produces quality product and the subsequent evaluation of its performance is needed before commercial acceptance of the AeRock product

  4. Right upper quadrant pain

    International Nuclear Information System (INIS)

    Ralls, P.W.; Colletti, P.M.; Boswell, W.D. Jr.; Halls, J.M.

    1984-01-01

    Historically, assessment of acute right upper quadrant abdominal pain has been a considerable clinical challenge. While clinical findings and laboratory data frequently narrow the differential diagnosis, symptom overlap generally precludes definitive diagnosis among the various diseases causing acute right upper quadrant pain. Fortunately, the advent of newer diagnostic imaging modalities has greatly improved the rapidity and reliability of diagnosis in these patients. An additional challenge to the physician, with increased awareness of the importance of cost effectiveness in medicine, is to select appropriate diagnostic schema that rapidly establish accurate diagnoses in the most economical fashion possible. The dual goals of this discussion are to assess not only the accuracy of techniques used to evaluate patients with acute right upper quadrant pain, but also to seek out cost-effective, coordinated imaging techniques to achieve this goal

  5. Synergistic Allocation of Flight Expertise on the Flight Deck (SAFEdeck): A Design Concept to Combat Mode Confusion, Complacency, and Skill Loss in the Flight Deck

    Science.gov (United States)

    Schutte, Paul; Goodrich, Kenneth; Williams, Ralph

    2016-01-01

    This paper presents a new design and function allocation philosophy between pilots and automation that seeks to support the human in mitigating innate weaknesses (e.g., memory, vigilance) while enhancing their strengths (e.g., adaptability, resourcefulness). In this new allocation strategy, called Synergistic Allocation of Flight Expertise in the Flight Deck (SAFEdeck), the automation and the human provide complementary support and backup for each other. Automation is designed to be compliant with the practices of Crew Resource Management. The human takes a more active role in the normal operation of the aircraft without adversely increasing workload over the current automation paradigm. This designed involvement encourages the pilot to be engaged and ready to respond to unexpected situations. As such, the human may be less prone to error than the current automation paradigm.

  6. Upper airway evaluation

    International Nuclear Information System (INIS)

    Hoffman, E.A.; Gefter, W.B.; Schnall, M.; Nordberg, J.; Listerud, J.; Lenkinski, R.E.

    1988-01-01

    The authors are evaluating upper-airway sleep disorders with magnetic resonance (MR) imaging and x-ray cine computed tomography (CT). Fixed structural anatomy is visualized with multisection spin-echo MR imaging, the dynamic component with cine CT. Unique aspects of the study are described in this paper

  7. Upper gastrointestinal alterations in kidney transplant candidates.

    Science.gov (United States)

    Homse Netto, João Pedro; Pinheiro, João Pedro Sant'Anna; Ferrari, Mariana Lopes; Soares, Mirella Tizziani; Silveira, Rogério Augusto Gomes; Maioli, Mariana Espiga; Delfino, Vinicius Daher Alvares

    2018-05-14

    The incidence of gastrointestinal disorders among patients with chronic kidney disease (CKD) is high, despite the lack of a good correlation between endoscopic findings and symptoms. Many services thus perform upper gastrointestinal (UGI) endoscopy on kidney transplant candidates. This study aims to describe the alterations seen on the upper endoscopies of 96 kidney-transplant candidates seen from 2014 to 2015. Ninety-six CKD patients underwent upper endoscopic examination as part of the preparation to receive kidney grafts. The data collected from the patients' medical records were charted on Microsoft Office Excel 2016 and presented descriptively. Mean values, medians, interquartile ranges and 95% confidence intervals of the clinic and epidemiological variables were calculated. Possible associations between endoscopic findings and infection by H. pylori were studied. Males accounted for 54.17% of the 96 patients included in the study. Median age and time on dialysis were 50 years and 50 months, respectively. The most frequent upper endoscopy finding was enanthematous pangastritis (57.30%), followed by erosive esophagitis (30.20%). Gastric intestinal metaplasia and peptic ulcer were found in 8.33% and 7.30% of the patients, respectively. H. pylori tests were positive in 49 patients, and H. pylori infection was correlated only with non-erosive esophagitis (P = 0.046). Abnormal upper endoscopy findings were detected in all studied patients. This study suggested that upper endoscopy is a valid procedure for kidney transplant candidates. However, prospective studies are needed to shed more light on this matter.

  8. Comparison between major repair and replacement options for a bridge deck life cycle assessment: A case study

    Directory of Open Access Journals (Sweden)

    Abu Dabous Saleh

    2017-01-01

    Full Text Available Material production, manufacturing, transportation, usage, and end of lifeprocessing are usually the main contributors defining the life cycle assessment (LCA. Bridge infrastructure is important to the economy and the society. Over their life cycle, highway bridges experience several stressors that can significantly affect their structural performance and therefore require rehabilitation. This paper discusses the life cycle analysis of bridge rehabilitation decisions and demonstrates the analysis with a case study of a bridge located in Ontario, Canada. The LCA of the bridge deck is analyzed for two rehabilitation strategies: major repair and replacement. The study focuses on evaluating the different life cycle phases of the bridge deck by assessing their carbon dioxide emission, energy consumption and cost. Also, the paper presents the impact of the different elements within each phase to identify the most contributing elements. The LCA of the bridge deck is analyzed and estimated with the aid of CES EduPack 2016 software that includes a database of more than 4000 different materials and more than 200 manufacturing processes. Analysis of the case study shows that material phase causes significant life cycle impact. The study concluded that the deck replacement yields higher environmental impact and life cycle cost compared to repairing and strengthening the deck.

  9. Deck and Cable Dynamic Testing of a Single-span Bridge Using Radar Interferometry and Videometry Measurements

    Science.gov (United States)

    Piniotis, George; Gikas, Vassilis; Mpimis, Thanassis; Perakis, Harris

    2016-03-01

    This paper presents the dynamic testing of a roadway, single-span, cable-stayed bridge for a sequence of static load and ambient vibration monitoring scenarios. Deck movements were captured along both sideways of the bridge using a Digital Image Correlation (DIC) and a Ground-based Microwave Interfererometer (GBMI) system. Cable vibrations were measured at a single point location on each of the six cables using the GBMI technique. Dynamic testing involves three types of analyses; firstly, vibration analysis and modal parameter estimation (i. e., natural frequencies and modal shapes) of the deck using the combined DIC and GBMI measurements. Secondly, dynamic testing of the cables is performed through vibration analysis and experimental computation of their tension forces. Thirdly, the mechanism of cable-deck dynamic interaction is studied through their Power Spectra Density (PSD) and the Short Time Fourier Transform (STFT) analyses. Thereby, the global (deck and cable) and local (either deck or cable) bridge modes are identified, serving a concrete benchmark of the current state of the bridge for studying the evolution of its structural performance in the future. The level of synergy and complementarity between the GBMI and DIC techniques for bridge monitoring is also examined and assessed.

  10. On the design of flight-deck procedures

    Science.gov (United States)

    Degani, Asaf; Wiener, Earl L.

    1994-01-01

    In complex human-machine systems, operations, training, and standardization depend on a elaborate set of procedures which are specified and mandated by the operational management of the organization. The intent is to provide guidance to the pilots, to ensure a logical, efficient, safe, and predictable means of carrying out the mission objectives. In this report the authors examine the issue of procedure use and design from a broad viewpoint. The authors recommend a process which we call 'The Four P's:' philosophy, policies, procedures, and practices. We believe that if an organization commits to this process, it can create a set of procedures that are more internally consistent, less confusing, better respected by the flight crews, and that will lead to greater conformity. The 'Four-P' model, and the guidelines for procedural development in appendix 1, resulted from cockpit observations, extensive interviews with airline management and pilots, interviews and discussion at one major airframe manufacturer, and an examination of accident and incident reports. Although this report is based on airline operations, we believe that the principles may be applicable to other complex, high-risk systems, such as nuclear power production, manufacturing process control, space flight, and military operations.

  11. Clinical observation of the glaucoma trabeculectomy with tunnel knife making the double-deck scleral flap

    Directory of Open Access Journals (Sweden)

    Min Fu

    2015-07-01

    Full Text Available AIM: To study the trabeculectomy clinical effect of use tunnel knife to make double-deck scleral flap and to cut off the layer scleral flap of glaucoma.METHODS:Using the random grouping method to divide 46 cases(60 eyesof glaucoma into the treatment group of 24 cases(32 eyesand control group of 22 cases(28 eyes. The treatment group, tunnel knife was used to make double-deck sclera flap and superficial scleral flap about the size of 5mm×5.5mm,1/3 scleral thickness, under the sclera flap made another one about the size of 3.5mm×4mm, 1/3 scleral thickness, resected the middle layer of the sclera flap, removed 2mm×2mm trabecular tissue, underwent routine peripheral iridectomy, could adjust suture the superficial scleral flap, sutured Ball fascia and bulbar conjunctiva. In control group, routine glaucoma trabeculectomy was undergone.RESULTS:Patients were followed up for 1a, the vision in treatment group was obviously better than that in the control group, with a statistically significant difference(PP>0.05. But after 6 and 12mo, the intraocular pressure of the treatment group were significantly lower than that of the control group, with statistically significant difference(PPCONCLUSION:The trabeculectomy have a good effect to lower the intraocular pressure by use tunnel knife to make double-deck scleral flap and to cut off the layer scleral flap. The scleral flap have uniform thickness, smooth surface, and the function of the filtering bleb maintained for a long time, less postoperative complications, suitable for various types of glaucoma, so it is worthy of clinical promotion.

  12. Comparison of Controller and Flight Deck Algorithm Performance During Interval Management with Dynamic Arrival Trees (STARS)

    Science.gov (United States)

    Battiste, Vernol; Lawton, George; Lachter, Joel; Brandt, Summer; Koteskey, Robert; Dao, Arik-Quang; Kraut, Josh; Ligda, Sarah; Johnson, Walter W.

    2012-01-01

    Managing the interval between arrival aircraft is a major part of the en route and TRACON controller s job. In an effort to reduce controller workload and low altitude vectoring, algorithms have been developed to allow pilots to take responsibility for, achieve and maintain proper spacing. Additionally, algorithms have been developed to create dynamic weather-free arrival routes in the presence of convective weather. In a recent study we examined an algorithm to handle dynamic re-routing in the presence of convective weather and two distinct spacing algorithms. The spacing algorithms originated from different core algorithms; both were enhanced with trajectory intent data for the study. These two algorithms were used simultaneously in a human-in-the-loop (HITL) simulation where pilots performed weather-impacted arrival operations into Louisville International Airport while also performing interval management (IM) on some trials. The controllers retained responsibility for separation and for managing the en route airspace and some trials managing IM. The goal was a stress test of dynamic arrival algorithms with ground and airborne spacing concepts. The flight deck spacing algorithms or controller managed spacing not only had to be robust to the dynamic nature of aircraft re-routing around weather but also had to be compatible with two alternative algorithms for achieving the spacing goal. Flight deck interval management spacing in this simulation provided a clear reduction in controller workload relative to when controllers were responsible for spacing the aircraft. At the same time, spacing was much less variable with the flight deck automated spacing. Even though the approaches taken by the two spacing algorithms to achieve the interval management goals were slightly different they seem to be simpatico in achieving the interval management goal of 130 sec by the TRACON boundary.

  13. Structural condition assessment and service load performance of deteriorated prestressed concrete deck beam bridges

    Science.gov (United States)

    Fuentes, Juan Bolivar

    Precast pretensioned deck beam bridges are a generic bridge type widely used by IDOT for new construction through the end of the 1970's and still widely used on county roads throughout Illinois. While these bridges were economical to build, IDOT discontinued their use because reflective cracks developed along the length of the longitudinal joints between beams. Three 30 years old deteriorated beams were removed from an existing bridge over Spoon River in Fulton County, IL and delivered to Newmark Civil Engineering Laboratory. The program consisted of a series of comprehensive, destructive and non-destructive, tests and evaluations of the three beams with emphasis on three major areas; (1) The Condition Assessment of the as-delivered beams. (2) The service load performance of the bridge sub-assemblage constructed from those beams. After a comprehensive inspection of the beams was completed, the beams were integrated together into a bridge subassembly that simulated a bridge lane. (3) Following the service load tests, the three beams were separated and tested individually to failure. The critical signs to be observed in existing structures that will lead the inspectors to conclude that a deck beam is being overloaded were are also studied. Several conclusions were found. Cracking of the longitudinal joint has little effect on the stiffness of the bridge if the transverse rod is snug. The presence of a snug transverse tie rod increases the strength of the longitudinal joint. After a longitudinal joint has fractured, reincorporating a snug transverse rod can significantly reestablish the stiffness of the longitudinal joint and reduce overloading of a deteriorated beam. Participation factors must be based on relative bending moments of one beam with respect to the total amount of bending moment produced by the applied load and not to the amount of total vertical displacement. The participation factors will vary along the span of the bridge deck and will depend on the

  14. Study of deflection and crack interrelation that use deck slab's automatic measurement

    International Nuclear Information System (INIS)

    Park, Sung Woo; Park, Yung Suk; Joo, Kwon Yong

    2004-01-01

    Reinforce concrete slab executes finish work if 6 - 8 hours pass since concrete placing. Specially, because minimize process composition slab occasion early space-time that use structure deck plate, concrete strength revelation is very important. The reason is that when strength revelation is not made, fine shock and deflection can provoke concrete crack. Executed radio automatic measure to prevent these crack initiation cause in the advance. Apply radio automatic measure is il-san culture center building and pasta measure period 03/09/06 - 03/10/08.

  15. Attachments for fire modeling for Building 221-T, T Plant canyon deck and railroad tunnel

    International Nuclear Information System (INIS)

    Oar, D.L.

    1995-01-01

    The purpose of this attachment is to provide historical information and documentation for Document No. WHC-SD-CP-ANAL-008 Rev 0, ''Fire Modeling for Building 221-T--T Plant Canyon Deck and Railroad Tunnel'', dated September 29, 1994. This data compilation contains the following: Resumes of the Technical Director, Senior Engineer and Junior Engineer; Review and Comment Record; Software Files; CFAST Input and Output Files; Calculation Control Sheets; and Estimating Sprinkler Actuation Time in the Canyon and Railroad Tunnel. The T Plant was originally a fuel reprocessing facility. It was modified later to decontaminate and repair PuRex process equipment

  16. STS-42 Payload Specialist Merbold with drink on OV-103's aft flight deck

    Science.gov (United States)

    1992-01-01

    STS-42 Payload Specialist Ulf D. Merbold, wearing a lightweight headset (HDST), experiments with a grapefruit drink and straw on the aft flight deck of Discovery, Orbiter Vehicle (OV) 103. Merbold watches the liquid ball of grapefruit drink he created float in the weightlessness of space. The Los Angeles Dodger cap Merbold is wearing is part of a tribute to Manley L. (Sonny) Carter, originally assigned as a mission specialist on this flight. During the eight-day flight, the crewmembers each wore the cap on a designated day. Carter, a versatile athlete and avid Dodger fan, died in the crash of a commuter airline in 1991.

  17. Numisheet2005 Benchmark Analysis on Forming of an Automotive Deck Lid Inner Panel: Benchmark 1

    International Nuclear Information System (INIS)

    Buranathiti, Thaweepat; Cao Jian

    2005-01-01

    Numerical simulations in sheet metal forming processes have been a very challenging topic in industry. There are many computer codes and modeling techniques existing today. However, there are many unknowns affecting the prediction accuracy. Systematic benchmark tests are needed to accelerate the future implementations and to provide as a reference. This report presents an international cooperative benchmark effort for an automotive deck lid inner panel. Predictions from simulations are analyzed and discussed against the corresponding experimental results. The correlations between accuracy of each parameter of interest are discussed in this report

  18. Upper urinary tract tumors

    DEFF Research Database (Denmark)

    Gandrup, Karen L; Nordling, Jørgen; Balslev, Ingegerd

    2014-01-01

    BACKGROUND: Computed tomography urography (CTU) is used widely in the work-up of patients with symptoms of urinary tract lesions. Preoperative knowledge of whether a tumor is invasive or non-invasive is important for the choice of surgery. So far there are no studies about the distinction...... of invasive and non-invasive tumors in ureter and renal pelvis based on the enhancement measured with Hounsfield Units. PURPOSE: To examine the value of CTU using split-bolus technique to distinguish non-invasive from invasive urothelial carcinomas in the upper urinary tract. MATERIAL AND METHODS: Patients...... obtained at CTU could distinguish between invasive and non-invasive lesions. No patients had a CTU within the last year before the examination that resulted in surgery. CONCLUSION: A split-bolus CTU cannot distinguish between invasive and non-invasive urothelial tumors in the upper urinary tract...

  19. 33 CFR 149.419 - Can the water supply for the helicopter deck fire protection system be part of a fire water system?

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Can the water supply for the... § 149.419 Can the water supply for the helicopter deck fire protection system be part of a fire water system? (a) The water supply for the helicopter deck fire protection system required under § 149.420 or...

  20. Interventional studies of the upper gastrointestinal tract

    International Nuclear Information System (INIS)

    Shapiro, B.; Gross, M.D.

    1985-01-01

    Nuclear Medicine studies of the upper gastrointestinal (GI) tract provide a means whereby physiologic and pathophysiologic features can be observed from a unique and noninvasive perspective. While nuclear medicine studies by their very nature lack the high spatial resolution of the radiographic approach, the data derived are readily quantitated and presented in numerical fashion to provide functional and dynamic information in which the influences of interventions may be observed. This chapter outlines the scope of such interventions in studies of the upper GI tract with emphasis on examinations for gastroesophageal reflux and gastric emptying. The interactions of nutrients, physical maneuvers of pharmacologic agents on nuclear medicine studies of the upper GI tract may be intentional to render a test more sensitive or to evaluate the effect of therapy, or may represent an unintentional side effect that must be taken into account if misinterpretation is to be avoided

  1. Load test of the 3701U Building roof deck and support structure

    International Nuclear Information System (INIS)

    McCoy, R.M.

    1994-01-01

    The 3701U Building roof area was load tested according to the approved load-test procedure. The 3701U Building is located in the 300 Area of the Hanford Site and has the following characteristics: Roof deck--metal decking supported by steel purlins; Roof membrane--tar and gravel; Roof slope--flat (<10 deg); and Roof elevation--height of about 12.5 ft. The 3701U Building was visited in August 1992 for a visual inspection, but because of insulation an inspection could not be performed. The building was revisited in March 1994 for the purpose of writing this test report. Because the roof could not be inspected, a test was determined to be the best way to qualify the roof for personnel access. The test procedure called for the use of a remotely-controlled robot. The conclusions are that the roof has been qualified for 500-lb total roof load and that the ''No Roof Access'' signs can be changed to ''Roof Access Restricted'' signs

  2. A review on the suitability of rubberized concrete for concrete bridge decks

    Science.gov (United States)

    Syamir Senin, Mohamad; Shahidan, Shahiron; Radziah Abdullah, Siti; Anting Guntor, Nickholas; Syazani Leman, Alif

    2017-11-01

    Road authorities manage a large population of ageing bridges, a substantial number of which fail to meet the current requirements either due to deterioration and other structural deficiencies or as a result of the escalating demands imposed by increased traffic. This problem is related to the dynamic load from vehicles. This problem can be solved by producing a type of concrete that can reduce the amplitude of oscillation or vibration such as rubberized concrete. Green construction has been a very important aspect in concrete production field in the last decade. One of the most problematic waste materials is scrap tires. The use of scrap tires in civil engineering is increasing by producing rubberized concrete. Rubberized concrete is a type of concrete that is mixed with rubber. The purpose of this review is to justify the suitability of rubberized concrete for concrete bridge decks. Several parameters named physical, chemical and mechanical properties were measured to ensure the suitability of rubberized concrete for concrete bridge decks. Rubberized concrete has similar workability to normal concrete. The rubber reduced the density and compressive strength of the concrete while increased the flexural strength, water absorption and damping ratio. The used of rubber in concrete beyond 20% is not recommended due to decreasing in compressive strength. Rubberized concrete recommended to be used in circumstances where vibration damping was required such as in bridge construction as shock-wave absorber.

  3. Reducing commercial fishing deck hazards with engineering solutions for winch design.

    Science.gov (United States)

    Lincoln, Jennifer M; Lucas, Devin L; McKibbin, Robert W; Woodward, Chelsea C; Bevan, John E

    2008-01-01

    The majority (67%) of hospitalized injuries among Alaska commercial fishermen are associated with deck machinery. This paper describes the "Prevention Through Design" process to mitigate one serious machinery entanglement hazard posed by a capstan deck winch. After observing that the capstan winch provides no entanglement protection and the hydraulic controls are usually out of reach of the entangled person, NIOSH personnel met with fishermen and winch manufacturers to discuss various design solutions to mitigate these hazards. An emergency-stop ("e-stop") system was developed that incorporated a momentary contact button that when pushed, switches a safety-relay that de-energizes the solenoid of an electro-hydraulic valve stopping the rotating winch. The vessel owners that had the e-stop installed enthusiastically recommend it to other fishermen. NIOSH entered into a Proprietary Technology Licensing Agreement with a company to develop the system for commercial use. This is an example of a practical engineering control that effectively protects workers from a hazardous piece of equipment by preventing injuries due to entanglement. This solution could reduce these types of debilitating injuries and fatalities in this industry.

  4. Design status and procurement activities of the High Voltage Deck 1 and Bushing for the ITER Neutral Beam Injector

    International Nuclear Information System (INIS)

    Boldrin, Marco; De Lorenzi, Antonio; Decamps, Hans; Grando, Luca; Simon, Muriel; Toigo, Vanni

    2013-01-01

    Highlights: ► ITER Neutral Beam Injector includes several non-standard components. ► The design status of the −1 MV dc HVD1 and Bushing is described. ► The paper reports also on the integrated layout of the two components. ► Preliminary electrostatic and thermal analyses are presented. ► Procurement activities are outlined. -- Abstract: The ITER Neutral Beam Injector (NBI) power supply system includes several non-standard components, whose ratings go beyond the present industrial practice. Two of these items, to be procured by Fusion for Energy, are: 1.A −1 MV dc air-insulated Faraday cage, called High Voltage Deck 1 (HVD1), hosting the Ion Source and Extractor Power Supplies (ISEPS) and the associated diagnostics. 2.A −1 MV dc feedthrough, called HVD1-TL Bushing, aimed at connecting the HVD1 to the gas (SF 6 ) insulated Transmission Line (TL), containing inside its High Voltage (HV) conductor all ISEPS power and control cables coming from the HVD1 to be connected to the NBI Ion Source services. The paper deals with the status of the design of the HVD1 and HVD1-TL Bushing, focusing on insulation, mechanical and thermal issues as well as on their integration with the other components of the power supply system. In particular, the insulation issue of the integrated system has been addressed by means of an electrostatic Finite Element (FE) analysis whilst a FE thermal simulation has been carried out to assess the impact of the dissipation of the proposed design of the inner conductors (ISEPS conductors) not actively cooled. Finally, the paper describes the status of procurement strategy and execution

  5. Design status and procurement activities of the High Voltage Deck 1 and Bushing for the ITER Neutral Beam Injector

    Energy Technology Data Exchange (ETDEWEB)

    Boldrin, Marco, E-mail: marco.boldrin@igi.cnr.it [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy); De Lorenzi, Antonio [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy); Decamps, Hans [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France); Grando, Luca [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy); Simon, Muriel [Fusion For Energy, c/ Josep Pla 2, 08019 Barcelona (Spain); Toigo, Vanni [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy)

    2013-10-15

    Highlights: ► ITER Neutral Beam Injector includes several non-standard components. ► The design status of the −1 MV{sub dc} HVD1 and Bushing is described. ► The paper reports also on the integrated layout of the two components. ► Preliminary electrostatic and thermal analyses are presented. ► Procurement activities are outlined. -- Abstract: The ITER Neutral Beam Injector (NBI) power supply system includes several non-standard components, whose ratings go beyond the present industrial practice. Two of these items, to be procured by Fusion for Energy, are: 1.A −1 MV{sub dc} air-insulated Faraday cage, called High Voltage Deck 1 (HVD1), hosting the Ion Source and Extractor Power Supplies (ISEPS) and the associated diagnostics. 2.A −1 MV{sub dc} feedthrough, called HVD1-TL Bushing, aimed at connecting the HVD1 to the gas (SF{sub 6}) insulated Transmission Line (TL), containing inside its High Voltage (HV) conductor all ISEPS power and control cables coming from the HVD1 to be connected to the NBI Ion Source services. The paper deals with the status of the design of the HVD1 and HVD1-TL Bushing, focusing on insulation, mechanical and thermal issues as well as on their integration with the other components of the power supply system. In particular, the insulation issue of the integrated system has been addressed by means of an electrostatic Finite Element (FE) analysis whilst a FE thermal simulation has been carried out to assess the impact of the dissipation of the proposed design of the inner conductors (ISEPS conductors) not actively cooled. Finally, the paper describes the status of procurement strategy and execution.

  6. MEAN OF MEDIAN ABSOLUTE DERIVATION TECHNIQUE MEAN ...

    African Journals Online (AJOL)

    eobe

    development of mean of median absolute derivation technique based on the based on the based on .... of noise mean to estimate the speckle noise variance. Noise mean property ..... Foraging Optimization,” International Journal of. Advanced ...

  7. in upper gastrointestinal endoscopy

    Directory of Open Access Journals (Sweden)

    Sinan Uzman

    2016-07-01

    Full Text Available Introduction : There is increasing interest in sedation for upper gastrointestinal endoscopy (UGE. Prospective randomized studies comparing sedation properties and complications of propofol and midazolam/meperidine in upper gastrointestinal endoscopy (UGE are few. Aim: To compare propofol and midazolam/meperidine sedation for UGE in terms of cardiopulmonary side effects, patient and endoscopist satisfaction and procedure-related times. Material and methods: This was a prospective, randomized, double-blind study of propofol versus midazolam and meperidine in 100 patients scheduled for diagnostic upper gastrointestinal endoscopy. The patients were divided into propofol and midazolam/meperidine groups. Randomization was generated by a computer. Cardiopulmonary side effects (hypotension, bradycardia, hypoxemia, procedure-related times (endoscopy time, awake time, time to hospital discharge, and patient and endoscopist satisfaction were compared between groups. Results: There was no significant difference between the groups with respect to the cost, endoscopy time, or demographic and clinical characteristics of the patients. Awake time and time to hospital discharge were significantly shorter in the propofol group (6.58 ±4.72 vs. 9.32 ±4.26 min, p = 0.030 and 27.60 ±7.88 vs. 32.00 ±10.54 min, p = 0.019. Hypotension incidence was significantly higher in the propofol group (12% vs. 0%, p = 0.027. The patient and endoscopist satisfaction was better with propofol. Conclusions : Propofol may be preferred to midazolam/meperidine sedation, with a shorter awake and hospital discharge time and better patient and endoscopist satisfaction. However, hypotension risk should be considered with propofol, and careful evaluation is needed, particularly in cardiopulmonary disorders.

  8. Upper extremity golf injuries.

    Science.gov (United States)

    Cohn, Michael A; Lee, Steven K; Strauss, Eric J

    2013-01-01

    Golf is a global sport enjoyed by an estimated 60 million people around the world. Despite the common misconception that the risk of injury during the play of golf is minimal, golfers are subject to a myriad of potential pathologies. While the majority of injuries in golf are attributable to overuse, acute traumatic injuries can also occur. As the body's direct link to the golf club, the upper extremities are especially prone to injury. A thorough appreciation of the risk factors and patterns of injury will afford accurate diagnosis, treatment, and prevention of further injury.

  9. Upper Limit for Regional Sea Level Projections

    Science.gov (United States)

    Jevrejeva, Svetlana; Jackson, Luke; Riva, Riccardo; Grinsted, Aslak; Moore, John

    2016-04-01

    With more than 150 million people living within 1 m of high tide future sea level rise is one of the most damaging aspects of warming climate. The latest Intergovernmental Panel on Climate Change report (AR5 IPCC) noted that a 0.5 m rise in mean sea level will result in a dramatic increase the frequency of high water extremes - by an order of magnitude, or more in some regions. Thus the flood threat to the rapidly growing urban populations and associated infrastructure in coastal areas are major concerns for society. Hence, impact assessment, risk management, adaptation strategy and long-term decision making in coastal areas depend on projections of mean sea level and crucially its low probability, high impact, upper range. With probabilistic approach we produce regional sea level projections taking into account large uncertainties associated with Greenland and Antarctica ice sheets contribution. We calculate the upper limit (as 95%) for regional sea level projections by 2100 with RCP8.5 scenario, suggesting that for the most coastlines upper limit will exceed the global upper limit of 1.8 m.

  10. Necessity of Proper Lashing of Containers on the Ship's Deck as Part of Optimization of the Sea Voyage

    Directory of Open Access Journals (Sweden)

    Zoran Radišić

    2004-03-01

    Full Text Available These days we are witnessing an increase of container trafficin general and at sea in particular. In order to economizetheir business the ship owners are building bigger container vesselswhich can carry up to 8000 TEUs (Maersk line and otherbig carriers are following suit. On the drawing board is the vesselof 12000 TEUs from the mentioned ship owner. Obviously,such large quantity of containers requires highly efficient lashingequipment in order to secure them, particularly thosestowed on the deck Under the deck, almost as a rule all contemporarycontainer ships have cell guides as securing devices.Attention in this work is focused on container lashing systemexposed on the ship's deck and the relevant forces acting on thelash system during transportation at sea. Once containers areloaded on the ship's deck they should be safely secured by oneof the lashing systems in order to prevent damage and that is theprincipal task of the lashing equipment engaged within theframe of the lash system. In order to fulfill its objective theforces acting on the container should be properly calculated.The acting forces, their influence and the way of calculatingthem have been explained for all the major ship movementsand suggestions for optimum lashing equipment are given.

  11. A Double-Deck Elevator Group Supervisory Control System with Destination Floor Guidance System Using Genetic Network Programming

    Science.gov (United States)

    Yu, Lu; Zhou, Jin; Mabu, Shingo; Hirasawa, Kotaro; Hu, Jinglu; Markon, Sandor

    The Elevator Group Supervisory Control Systems (EGSCS) are the control systems that systematically manage three or more elevators in order to efficiently transport the passengers in buildings. Double-deck elevators, where two elevators are connected with each other, serve passengers at two consecutive floors simultaneously. Double-deck Elevator systems (DDES) become more complex in their behavior than conventional single-deck elevator systems (SDES). Recently, Artificial Intelligence (AI) technology has been used in such complex systems. Genetic Network Programming (GNP), a graph-based evolutionary method, has been applied to EGSCS and its advantages are shown in some papers. GNP can obtain the strategy of a new hall call assignment to the optimal elevator when it performs crossover and mutation operations to judgment nodes and processing nodes. Meanwhile, Destination Floor Guidance System (DFGS) is installed in DDES, so that passengers can also input their destinations at elevator halls. In this paper, we have applied GNP to DDES and compared DFGS with normal systems. The waiting time and traveling time of DFGS are all improved because of getting more information from DFGS. The simulations showed the effectiveness of the double-deck elevators with DFGS in different building traffics.

  12. Reliability Analysis of Offshore Jacket Structures with Wave Load on Deck using the Model Correction Factor Method

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Friis-Hansen, P.; Nielsen, J.S.

    2006-01-01

    failure/collapse of jacket type platforms with wave in deck loads using the so-called Model Correction Factor Method (MCFM). A simple representative model for the RSR measure is developed and used in the MCFM technique. A realistic example is evaluated and it is seen that it is possible to perform...

  13. Benefits of measuring half-cell potentials and rebar corrosion rates in condition surveys of concrete bridge decks.

    Science.gov (United States)

    1992-01-01

    The practice of conducting a half-cell potential survey during the assessment of the condition of a concrete deck was reexamined with the objective of eliminating some of the doubts concerning its benefits. It was found that the survey grid size of 4...

  14. A Usability and Learnability Case Study of Glass Flight Deck Interfaces and Pilot Interactions through Scenario-based Training

    Science.gov (United States)

    De Cino, Thomas J., II

    In the aviation industry, digitally produced and presented flight, navigation, and aircraft information is commonly referred to as glass flight decks. Glass flight decks are driven by computer-based subsystems and have long been a part of military and commercial aviation sectors. Over the past 15 years, the General Aviation (GA) sector of the aviation industry has become a recent beneficiary of the rapid advancement of computer-based glass flight deck (GFD) systems. While providing the GA pilot considerable enhancements in the quality of information about the status and operations of the aircraft, training pilots on the use of glass flight decks is often delivered with traditional methods (e.g. textbooks, PowerPoint presentations, user manuals, and limited computer-based training modules). These training methods have been reported as less than desirable in learning to use the glass flight deck interface. Difficulties in achieving a complete understanding of functional and operational characteristics of the GFD systems, acquiring a full understanding of the interrelationships of the varied subsystems, and handling the wealth of flight information provided have been reported. Documented pilot concerns of poor user experience and satisfaction, and problems with the learning the complex and sophisticated interface of the GFD are additional issues with current pilot training approaches. A case study was executed to explore ways to improve training using GFD systems at a Midwestern aviation university. The researcher investigated if variations in instructional systems design and training methods for learning glass flight deck technology would affect the perceptions and attitudes of pilots of the learnability (an attribute of usability) of the glass flight deck interface. Specifically, this study investigated the effectiveness of scenario-based training (SBT) methods to potentially improve pilot knowledge and understanding of a GFD system, and overall pilot user

  15. A guidance on MELCOR input preparation : An input deck for Ul-Chin 3 and 4 Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Song Won

    1997-02-01

    The objective of this study is to enhance the capability of assessing the severe accident sequence analyses and the containment behavior using MELCOR computer code and to provide the guideline of its efficient use. This report shows the method of the input deck preparation as well as the assessment strategy for the MELCOR code. MELCOR code is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor nuclear power plants. The code is being developed at Sandia National Laboratories for the U.S. NRC as a second generation plant risk assessment tool and the successor to the source term code package. The accident sequence of the reference input deck prepared in this study for Ulchin unit 3 and 4 nuclear power plants, is the total loss of feedwater (TLOFW) without any success of safety systems, which is similar to station blackout (TLMB). It is very useful to simulate a well-known sequence through the best estimated code or experiment, because the results of the simulation before core melt can be compared with the FSAR, but no data is available after core melt. The precalculation for the TLOFW using the reference input deck is performed successfully as expected. The other sequences will be carried out with minor changes in the reference input. This input deck will be improved continually by the adding of the safety systems not included in this input deck, and also through the sensitivity and uncertainty analyses. (author). 19 refs., 10 tabs., 55 figs.

  16. A guidance on MELCOR input preparation : An input deck for Ul-Chin 3 and 4 Nuclear Power Plant

    International Nuclear Information System (INIS)

    Cho, Song Won.

    1997-02-01

    The objective of this study is to enhance the capability of assessing the severe accident sequence analyses and the containment behavior using MELCOR computer code and to provide the guideline of its efficient use. This report shows the method of the input deck preparation as well as the assessment strategy for the MELCOR code. MELCOR code is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor nuclear power plants. The code is being developed at Sandia National Laboratories for the U.S. NRC as a second generation plant risk assessment tool and the successor to the source term code package. The accident sequence of the reference input deck prepared in this study for Ulchin unit 3 and 4 nuclear power plants, is the total loss of feedwater (TLOFW) without any success of safety systems, which is similar to station blackout (TLMB). It is very useful to simulate a well-known sequence through the best estimated code or experiment, because the results of the simulation before core melt can be compared with the FSAR, but no data is available after core melt. The precalculation for the TLOFW using the reference input deck is performed successfully as expected. The other sequences will be carried out with minor changes in the reference input. This input deck will be improved continually by the adding of the safety systems not included in this input deck, and also through the sensitivity and uncertainty analyses. (author). 19 refs., 10 tabs., 55 figs

  17. Enhanced Vision Flight Deck Technology for Commercial Aircraft Low-Visibility Surface Operations

    Science.gov (United States)

    Arthur, Jarvis J., III; Norman, R. Michael; Kramer, Lynda J.; Prinzel, Lawrence J., III; Ellis, Kyle K. E.; Harrison, Stephanie J.; Comstock, J. Ray

    2013-01-01

    NASA Langley Research Center and the FAA collaborated in an effort to evaluate the effect of Enhanced Vision (EV) technology display in a commercial flight deck during low visibility surface operations. Surface operations were simulated at the Memphis, TN (FAA identifier: KMEM) air field during nighttime with 500 Runway Visual Range (RVR) in a high-fidelity, full-motion simulator. Ten commercial airline flight crews evaluated the efficacy of various EV display locations and parallax and mini cation effects. The research paper discusses qualitative and quantitative results of the simulation experiment, including the effect of EV display placement on visual attention, as measured by the use of non-obtrusive oculometry and pilot mental workload. The results demonstrated the potential of EV technology to enhance situation awareness which is dependent on the ease of access and location of the displays. Implications and future directions are discussed.

  18. Enhanced vision flight deck technology for commercial aircraft low-visibility surface operations

    Science.gov (United States)

    Arthur, Jarvis J.; Norman, R. M.; Kramer, Lynda J.; Prinzel, Lawerence J.; Ellis, Kyle K.; Harrison, Stephanie J.; Comstock, J. R.

    2013-05-01

    NASA Langley Research Center and the FAA collaborated in an effort to evaluate the effect of Enhanced Vision (EV) technology display in a commercial flight deck during low visibility surface operations. Surface operations were simulated at the Memphis, TN (FAA identifier: KMEM) airfield during nighttime with 500 Runway Visual Range (RVR) in a high-fidelity, full-motion simulator. Ten commercial airline flight crews evaluated the efficacy of various EV display locations and parallax and minification effects. The research paper discusses qualitative and quantitative results of the simulation experiment, including the effect of EV display placement on visual attention, as measured by the use of non-obtrusive oculometry and pilot mental workload. The results demonstrated the potential of EV technology to enhance situation awareness which is dependent on the ease of access and location of the displays. Implications and future directions are discussed.

  19. Upper airway resistance syndrome.

    Science.gov (United States)

    Montserrat, J M; Badia, J R

    1999-03-01

    This article reviews the clinical picture, diagnosis and management of the upper airway resistance syndrome (UARS). Presently, there is not enough data on key points like the frequency of UARS and the morbidity associated with this condition. Furthermore, the existence of LIARS as an independent sleep disorder and its relation with snoring and obstructive events is in debate. The diagnosis of UARS is still a controversial issue. The technical limitations of the classic approach to monitor airflow with thermistors and inductance plethysmography, as well as the lack of a precise definition of hypopnea, may have led to a misinterpretation of UARS as an independent diagnosis from the sleep apnea/hypopnea syndrome. The diagnosis of this syndrome can be missed using a conventional polysomnographic setting unless appropriate techniques are applied. The use of an esophageal balloon to monitor inspiratory effort is currently the gold standard. However, other sensitive methods such as the use of a pneumotachograph and, more recently, nasal cannula/pressure transducer systems or on-line monitoring of respiratory impedance with the forced oscillation technique may provide other interesting possibilities. Recognition and characterization of this subgroup of patients within sleep breathing disorders is important because they are symptomatic and may benefit from treatment. Management options to treat UARS comprise all those currently available for sleep apnea/hypopnea syndrome (SAHS). However, the subset of patients classically identified as LIARS that exhibit skeletal craneo-facial abnormalities might possibly obtain further benefit from maxillofacial surgery.

  20. Upper Illinois River basin

    Science.gov (United States)

    Friedel, Michael J.

    1998-01-01

    During the past 25 years, industry and government made large financial investments that resulted in better water quality across the Nation; however, many water-quality concerns remain. Following a 1986 pilot project, the U.S. Geological Survey began implementation of the National Water-Quality Assessment (NAWQA) Program in 1991. This program differs from other national water-quality assessment studies in that the NAWQA integrates monitoring of surface- and ground-water quality with the study of aquatic ecosystems. The goals of the NAWQA Program are to (1) describe current water-quality conditions for a large part of the Nation's freshwater streams and aquifers (water-bearing sediments and rocks), (2) describe how water quality is changing over time, and (3) improve our understanding of the primary natural and human factors affecting water quality.The Upper Illinois River Basin National Water- Quality Assessment (NAWQA) study will increase the scientific understanding of surface- and ground-water quality and the factors that affect water quality in the basin. The study also will provide information needed by water-resource managers to implement effective water-quality management actions and evaluate long-term changes in water quality.

  1. The dance of meaning

    DEFF Research Database (Denmark)

    Rasmussen, Ole Elstrup

    2005-01-01

    competence, qualifications, sense making, reasoning, meaning, intentionality, interpersonal relationship......competence, qualifications, sense making, reasoning, meaning, intentionality, interpersonal relationship...

  2. A Computer Simulation Approach to the Study of Effects of Deck Surface Compliance on Initial Impact Impulse Forces in Human Gait

    National Research Council Canada - National Science Library

    Bretz, David

    2000-01-01

    .... One proposal for reducing knee disorders is to install more compliant decking The goal of this thesis is to develop a computer model of the human gait that estimates the transarticulation forces...

  3. Low speed wind tunnel test of ground proximity and deck edge effects on a lift cruise fan V/STOL configuration, volume 1

    Science.gov (United States)

    Stewart, V. R.

    1979-01-01

    The characteristics were determined of a lift cruise fan V/STOL multi-mission configuration in the near proximity to the edge of a small flat surface representation of a ship deck. Tests were conducted at both static and forward speed test conditions. The model (0.12 scale) tested was a four fan configuration with modifications to represent a three fan configuration. Analysis of data showed that the deck edge effects were in general less critical in terms of differences from free air than a full deck (in ground effect) configuration. The one exception to this was when the aft edge of the deck was located under the center of gravity. This condition, representative of an approach from the rear, showed a significant lift loss. Induced moments were generally small compared to the single axis control power requirements, but will likely add to the pilot work load.

  4. Upper gastrointestinal bleeding in irbid, jordan

    International Nuclear Information System (INIS)

    Banisalamah, A.A.; Mraiat, Z.M.

    2007-01-01

    To define the various causes of nonvariceal upper gastrointestinal bleeding, to outline management modalities and to determine the final outcome of patients. A retrospective analysis of patients presenting with upper gastrointestinal (UGI) bleeding from January 2003 to December 2006 (4 years) was conducted. Patients with endoscopically proven variceal bleeding were excluded. Out of the 120 patients, most of the patients belonged to an age group of more than 50 years (mean 48.5 years). Haematemesis was the most common presentation and Acute Gastric Mucosal Lesion (AGML) was the most frequently encountered lesion. The cause of bleeding was not identified in 10 patients (undetermined group). Twenty-two (18.3%) underwent surgery and we had an overall mortality of 15.8%. AGML being the leading cause can be managed conservatively most of the time. There is a male preponderance and the incidence and mortality increases with advancing age. The undetermined group remains a diagnostic problem. (author)

  5. Post learning sleep improves cognitive-emotional decision-making: evidence for a 'deck B sleep effect' in the Iowa Gambling Task.

    Science.gov (United States)

    Seeley, Corrine J; Beninger, Richard J; Smith, Carlyle T

    2014-01-01

    The Iowa Gambling Task (IGT) is widely used to assess real life decision-making impairment in a wide variety of clinical populations. Our study evaluated how IGT learning occurs across two sessions, and whether a period of intervening sleep between sessions can enhance learning. Furthermore, we investigate whether pre-sleep learning is necessary for this improvement. A 200-trial version of the IGT was administered at two sessions separated by wake, sleep or sleep and wake (time-of-day control). Participants were categorized as learners and non-learners based on initial performance in session one. In session one, participants initially preferred the high-frequency reward decks B and D, however, a subset of learners decreased choice from negative expected value 'bad' deck B and increased choices towards with a positive expected value 'good' decks (decks C and D). The learners who had a period of sleep (sleep and sleep/wake control conditions) between sessions showed significantly larger reduction in choices from deck B and increase in choices from good decks compared to learners that had intervening wake. Our results are the first to show that post-learning sleep can improve performance on a complex decision-making task such as the IGT. These results provide new insights into IGT learning and have important implications for understanding the neural mechanisms of "sleeping on" a decision.

  6. Post learning sleep improves cognitive-emotional decision-making: evidence for a 'deck B sleep effect' in the Iowa Gambling Task.

    Directory of Open Access Journals (Sweden)

    Corrine J Seeley

    Full Text Available The Iowa Gambling Task (IGT is widely used to assess real life decision-making impairment in a wide variety of clinical populations. Our study evaluated how IGT learning occurs across two sessions, and whether a period of intervening sleep between sessions can enhance learning. Furthermore, we investigate whether pre-sleep learning is necessary for this improvement. A 200-trial version of the IGT was administered at two sessions separated by wake, sleep or sleep and wake (time-of-day control. Participants were categorized as learners and non-learners based on initial performance in session one. In session one, participants initially preferred the high-frequency reward decks B and D, however, a subset of learners decreased choice from negative expected value 'bad' deck B and increased choices towards with a positive expected value 'good' decks (decks C and D. The learners who had a period of sleep (sleep and sleep/wake control conditions between sessions showed significantly larger reduction in choices from deck B and increase in choices from good decks compared to learners that had intervening wake. Our results are the first to show that post-learning sleep can improve performance on a complex decision-making task such as the IGT. These results provide new insights into IGT learning and have important implications for understanding the neural mechanisms of "sleeping on" a decision.

  7. From Deck Hand to Program Manager - 30 years with Research Vessels

    Science.gov (United States)

    Prince, J. M.

    2012-12-01

    Starting in 1980 as a Mate and Deck Hand and working my way up to Captain, Marine Superintendent, UNOLS Executive Secretary and now as an ONR Research Facilities Program Manager focused on the acquisition of two new Ocean Class Research Vessels, I have witnessed first hand the evolution of the U.S. Academic Research Fleet. The author will focus on a few key events in the evolution of the modern research fleet. As a deck hand, mate and Captain, I was involved in an early multi-disciplinary effort often using two ships working together to conduct sampling and analysis in Physical, Chemical and Biological oceanography. The VERTEX cruises led by John Martin and others used the R/V CAYUSE and R/V WECOMA extensively through out the NE Pacific Ocean conducting research that led to Dr. Martin's Iron Hypothesis. This work and that of others involving trace metal clean sampling and clean laboratories on board our ships pushed many new and demanding requirements for future vessels. As a ship scheduler and as chair of the Research Vessel Operators Committee (RVOC) I saw the increasing use of Remotely Operated Vehicles to complement the work being done with the ALVIN and other occupied submersibles. This led to scheduling challenges and changes to our safety standards, but also to many new opportunities for discoveries on the many mid-ocean ridges and hydro-thermal vent fields. More recently, Autonomous Underwater Vehicles (AUV) and Unmanned Aerial Vehicles (UAV) and aircraft have been used simultaneously with research vessels such as during a multi-PI, multi-ship program in the Monterey Bay. Communications at sea have changed dramatically in the past thirty years. No longer are we limited to reading the data from a spreadsheet over a Single Side Band radio so that the PI ashore can track the progress of a cruise and provide guidance for the next day's sampling. Full bandwidth communications are becoming the norm with the capability of streaming video from an ROV to shore or to

  8. [Darwinism and the meaning of "meaning"].

    Science.gov (United States)

    Castrodeza, Carlos

    2009-01-01

    The problem of the meaning of life is herewith contemplated from a Darwinian perspective. It is argued how factors such as existential depression, the concern about the meaning of "meaning," the problem of evil, death as the end of our personal identity, happiness as an unachievable goal, etc. may well have an adaptive dimension "controlled" neither by ourselves nor obscure third parties (conspiracy theories) but "simply" by our genes (replicators in general) so that little if anything is to be done to find a radical remedy for the human condition.

  9. A Cost Benefit Analysis Approach to Identify Improvements in Merchant Navy Deck Officers’ HELM (Human Element Leadership and Management Training

    Directory of Open Access Journals (Sweden)

    Farhan Saeed

    2016-12-01

    Full Text Available A review of maritime accidents conducted over the last decade confirms that human error is the main contributing factor in these incidents. Well-developed Non-Technical Skills (NTS can reduce the effects of human error. NTS include both interpersonal and cognitive skills such as situation awareness, teamwork, decision-making, leadership, managerial skills, communication and language skills. In a crisis situation good NTS allow a deck officer to recognise the problem quickly, take action to manage the situation, and utilise the available team members safely and effectively. This paper identifies the importance of NTS training for merchant navy deck officers. It also highlights room for improvement in the existing HELM training. Research has shown that at present the structure of HELM training is not very effective. The other safety critical domains’ efforts into NTS developments are investigated and examples of best practice are adapted into the maritime domain’s NTS training. Suggestions are given for improvements to the HELM course based on proven successful methods in other safety critical domains (aviation and anaesthesia. A subsequent Cost Benefit Analysis for improving deck officers’ NTS is also carried out through the use of Bayesian Networks and Decision Tree Modelling.

  10. Upper limb lymphedema after breast cancer treatment

    International Nuclear Information System (INIS)

    Ben Salah, H.; Bahri, M.; Jbali, B.; Daoud, J.; Guermazi, M.; Frikha, M.

    2012-01-01

    Purpose. - To study the frequency and risk factors for upper limb lymphedema through a series of patients treated for breast cancer. Patients and methods. - It is a retrospective study about 222 patients treated for breast cancer during the period between February 1993 and December 2003 in Sfax hospitals. Average age was 51 years (27-92 years). Tumour was T2 in 59% of cases. All patients had surgery with lymph node dissection. Infiltrating ductal carcinoma was the most frequent histological type (80% of cases), with predominant SBR II grade (62%). The mean number of removed lymph nodes was 12 (2-33). Axillary lymph node metastasis was detected in 124 patients. Radiotherapy was delivered in 200 patients, including axillary irradiation in 30 cases. The mean follow-up was 68 months (12-120). Results. - Lymphedema appeared in 23% of cases (51 patients), 14 months after surgery (mean period). Lymphedema affected the brachium in 17% of cases, the forearm in 12% of cases and all upper limb in 71% of cases. Fifty percent of patients had rehabilitation. However, improvement of lymphedema was obtained in 18 cases. Parameters predicting lymphedema were studied. Significant risk factors were obesity, infection and a number of removed lymph node above 10. The type of surgery, axillary irradiation and shoulder abduction deficit did not predict lymphedema. Conclusion. - Lymphedema of the arm is a frequent consequence of breast cancer treatment. The risk of lymphedema is correlated with obesity, infection and a number of removed lymph node above 10. (authors)

  11. DataComm in Flight Deck Surface Trajectory-Based Operations

    Science.gov (United States)

    Bakowski, Deborah L.; Foyle, David C.; Hooey, Becky L.; Meyer, Glenn R.; Wolter, Cynthia A.

    2012-01-01

    The purpose of this pilot-in-the-loop aircraft taxi simulation was to evaluate a NextGen concept for surface trajectory-based operations (STBO) in which air traffic control (ATC) issued taxi clearances with a required time of arrival (RTA) by Data Communications (DataComm). Flight deck avionics, driven by an error-nulling algorithm, displayed the speed needed to meet the RTA. To ensure robustness of the algorithm, the ability of 10 two-pilot crews to meet the RTA was tested in nine experimental trials representing a range of realistic conditions including a taxi route change, an RTA change, a departure clearance change, and a crossing traffic hold scenario. In some trials, these DataComm taxi clearances or clearance modifications were accompanied by 'preview' information, in which the airport map display showed a preview of the proposed route changes, including the necessary speed to meet the RTA. Overall, the results of this study show that with the aid of the RTA speed algorithm, pilots were able to meet their RTAs with very little time error in all of the robustness-testing scenarios. Results indicated that when taxi clearance changes were issued by DataComm only, pilots required longer notification distances than with voice communication. However, when the DataComm was accompanied by graphical preview, the notification distance required by pilots was equivalent to that for voice.

  12. DataComm in Flight Deck Surface Trajectory-Based Operations. Chapter 20

    Science.gov (United States)

    Bakowski, Deborah L.; Foyle, David C.; Hooey, Becky L.; Meyer, Glenn R.; Wolter, Cynthia A.

    2012-01-01

    The purpose of this pilot-in-the-loop aircraft taxi simulation was to evaluate a NextGen concept for surface trajectory-based operations (STBO) in which air traffic control (ATC) issued taxi clearances with a required time of arrival (RTA) by Data Communications (DataComm). Flight deck avionics, driven by an error-nulling algorithm, displayed the speed needed to meet the RTA. To ensure robustness of the algorithm, the ability of 10 two-pilot crews to meet the RTA was tested in nine experimental trials representing a range of realistic conditions including a taxi route change, an RTA change, a departure clearance change, and a crossing traffic hold scenario. In some trials, these DataComm taxi clearances or clearance modifications were accompanied by preview information, in which the airport map display showed a preview of the proposed route changes, including the necessary speed to meet the RTA. Overall, the results of this study show that with the aid of the RTA speed algorithm, pilots were able to meet their RTAs with very little time error in all of the robustness-testing scenarios. Results indicated that when taxi clearance changes were issued by DataComm only, pilots required longer notification distances than with voice communication. However, when the DataComm was accompanied by graphical preview, the notification distance required by pilots was equivalent to that for voice.

  13. Probability Analysis of the Wave-Slamming Pressure Values of the Horizontal Deck with Elastic Support

    Science.gov (United States)

    Zuo, Weiguang; Liu, Ming; Fan, Tianhui; Wang, Pengtao

    2018-06-01

    This paper presents the probability distribution of the slamming pressure from an experimental study of regular wave slamming on an elastically supported horizontal deck. The time series of the slamming pressure during the wave impact were first obtained through statistical analyses on experimental data. The exceeding probability distribution of the maximum slamming pressure peak and distribution parameters were analyzed, and the results show that the exceeding probability distribution of the maximum slamming pressure peak accords with the three-parameter Weibull distribution. Furthermore, the range and relationships of the distribution parameters were studied. The sum of the location parameter D and the scale parameter L was approximately equal to 1.0, and the exceeding probability was more than 36.79% when the random peak was equal to the sample average during the wave impact. The variation of the distribution parameters and slamming pressure under different model conditions were comprehensively presented, and the parameter values of the Weibull distribution of wave-slamming pressure peaks were different due to different test models. The parameter values were found to decrease due to the increased stiffness of the elastic support. The damage criterion of the structure model caused by the wave impact was initially discussed, and the structure model was destroyed when the average slamming time was greater than a certain value during the duration of the wave impact. The conclusions of the experimental study were then described.

  14. Methodology to Support Dynamic Function Allocation Policies Between Humans and Flight Deck Automation

    Science.gov (United States)

    Johnson, Eric N.

    2012-01-01

    Function allocation assigns work functions to all agents in a team, both human and automation. Efforts to guide function allocation systematically have been studied in many fields such as engineering, human factors, team and organization design, management science, cognitive systems engineering. Each field focuses on certain aspects of function allocation, but not all; thus, an independent discussion of each does not address all necessary aspects of function allocation. Four distinctive perspectives have emerged from this comprehensive review of literature on those fields: the technology-centered, human-centered, team-oriented, and work-oriented perspectives. Each perspective focuses on different aspects of function allocation: capabilities and characteristics of agents (automation or human), structure and strategy of a team, and work structure and environment. This report offers eight issues with function allocation that can be used to assess the extent to which each of issues exist on a given function allocation. A modeling framework using formal models and simulation was developed to model work as described by the environment, agents, their inherent dynamics, and relationships among them. Finally, to validate the framework and metrics, a case study modeled four different function allocations between a pilot and flight deck automation during the arrival and approach phases of flight.

  15. Pilot opinions on high level flight deck automation issues: Toward the development of a design philosophy

    Science.gov (United States)

    Tenney, Yvette J.; Rogers, William H.; Pew, Richard W.

    1995-01-01

    There has been much concern in recent years about the rapid increase in automation on commercial flight decks. The survey was composed of three major sections. The first section asked pilots to rate different automation components that exist on the latest commercial aircraft regarding their obtrusiveness and the attention and effort required in using them. The second section addressed general 'automation philosophy' issues. The third section focused on issues related to levels and amount of automation. The results indicate that pilots of advanced aircraft like their automation, use it, and would welcome more automation. However, they also believe that automation has many disadvantages, especially fully autonomous automation. They want their automation to be simple and reliable and to produce predictable results. The biggest needs for higher levels of automation were in pre-flight, communication, systems management, and task management functions, planning as well as response tasks, and high workload situations. There is an irony and a challenge in the implications of these findings. On the one hand pilots would like new automation to be simple and reliable, but they need it to support the most complex part of the job--managing and planning tasks in high workload situations.

  16. The approximation function of bridge deck vibration derived from the measured eigenmodes

    Directory of Open Access Journals (Sweden)

    Sokol Milan

    2017-12-01

    Full Text Available This article deals with a method of how to acquire approximate displacement vibration functions. Input values are discrete, experimentally obtained mode shapes. A new improved approximation method based on the modal vibrations of the deck is derived using the least-squares method. An alternative approach to be employed in this paper is to approximate the displacement vibration function by a sum of sine functions whose periodicity is determined by spectral analysis adapted for non-uniformly sampled data and where the parameters of scale and phase are estimated as usual by the least-squares method. Moreover, this periodic component is supplemented by a cubic regression spline (fitted on its residuals that captures individual displacements between piers. The statistical evaluation of the stiffness parameter is performed using more vertical modes obtained from experimental results. The previous method (Sokol and Flesch, 2005, which was derived for near the pier areas, has been enhanced to the whole length of the bridge. The experimental data describing the mode shapes are not appropriate for direct use. Especially the higher derivatives calculated from these data are very sensitive to data precision.

  17. Data link air traffic control and flight deck environments: Experiment in flight crew performance

    Science.gov (United States)

    Lozito, Sandy; Mcgann, Alison; Corker, Kevin

    1993-01-01

    This report describes an experiment undertaken in a full mission simulation environment to investigate the performance impact of, and human/system response to, data-linked Air Traffic Control (ATC) and automated flight deck operations. Subjects were twenty pilots (ten crews) from a major United States air carrier. Crews flew the Advanced Concepts Flight Simulator (ACFS), a generic 'glass cockpit' simulator at NASA Ames. The method of data link used was similar to the data link implementation plans for a next-generation aircraft, and included the capability to review ATC messages and directly enter ATC clearance information into the aircraft systems. Each crew flew experimental scenarios, in which data reflecting communication timing, errors and clarifications, and procedures were collected. Results for errors and clarifications revealed an interaction between communication modality (voice v. data link) and communication type (air/ground v. intracrew). Results also revealed that voice crews initiated ATC contact significantly more than data link crews. It was also found that data link crews performed significantly more extraneous activities during the communication task than voice crews. Descriptive data from the use of the review menu indicate the pilot-not-flying accessing the review menu most often, and also suggest diffulty in accessing the target message within the review menu structure. The overall impact of communication modality upon air/ground communication and crew procedures is discussed.

  18. Extensive upper respiratory tract sarcoidosis

    Science.gov (United States)

    Soares, Mafalda Trindade; Sousa, Carolina; Garanito, Luísa; Freire, Filipe

    2016-01-01

    Sarcoidosis is a chronic granulomatous disease of unknown aetiology. It can affect any part of the organism, although the lung is the most frequently affected organ. Upper airway involvement is rare, particularly if isolated. Sarcoidosis is a diagnosis of exclusion, established by histological evidence of non-caseating granulomas and the absence of other granulomatous diseases. The authors report a case of a man with sarcoidosis manifesting as a chronic inflammatory stenotic condition of the upper respiratory tract and trachea. PMID:27090537

  19. Meaning through Things

    Science.gov (United States)

    Johnson, Marilynn

    2017-01-01

    Interpretation is the process by which we find meaning in the things in the world around us: clouds on the horizon, bones, street signs, hairbrushes, uniforms, paintings, letters, and utterances. But where does that meaning come from and on what basis are we justified in saying a particular meaning is the right meaning? Drawing from debates in the…

  20. Upper limb position control in fibromyalgia

    Directory of Open Access Journals (Sweden)

    Bardal Ellen

    2012-09-01

    Full Text Available Abstract Background Motor problems are reported by patients with fibromyalgia (FM. However, the mechanisms leading to alterations in motor performance are not well understood. In this study, upper limb position control during sustained isometric contractions was investigated in patients with FM and in healthy controls (HCs. Methods Fifteen female FM patients and 13 HCs were asked to keep a constant upper limb position during sustained elbow flexion and shoulder abduction, respectively. Subjects received real-time visual feedback on limb position and both tasks were performed unloaded and while supporting loads (1, 2, and 3 kg. Accelerations of the dominant upper limb were recorded, with variance (SD of mean position and power spectrum analysis used to characterize limb position control. Normalized power of the acceleration signal was extracted for three frequency bands: 1–3 Hz, 4–7 Hz, and 8–12 Hz. Results Variance increased with load in both tasks (P 0.001 but did not differ significantly between patients and HCs (P > 0.17. Power spectrum analysis showed that the FM patients had a higher proportion of normalized power in the 1–3 Hz band, and a lower proportion of normalized power in the 8–12 Hz band compared to HCs (P 0.05. The results were consistent for all load conditions and for both elbow flexion and shoulder abduction. Conclusion FM patients exhibit an altered neuromuscular strategy for upper limb position control compared to HCs. The predominance of low-frequency limb oscillations among FM patients may indicate a sensory deficit.

  1. Upper Eyelid Fractional CO2 Laser Resurfacing With Incisional Blepharoplasty.

    Science.gov (United States)

    Kotlus, Brett S; Schwarcz, Robert M; Nakra, Tanuj

    2016-01-01

    Laser resurfacing, performed at the same time as blepharoplasty, has most commonly been applied to the lower eyelid skin but can effectively be used on the upper eyelid to reduce rhytidosis and improve skin quality. The authors evaluate the safety and efficacy of this procedure. Fractional CO2 laser resurfacing was performed in conjunction with incisional upper blepharoplasty. The ultrapulsed laser energy was applied to the sub-brow skin, the upper medial canthal skin, and the pretarsal skin in 30 patients. Photos were obtained preoperatively and at 3 months. All patients demonstrated reduction in upper eyelid rhytidosis without any serious complications. Independent rhytidosis grading (0-4) showed a mean improvement of 42%. One patient experienced wound dehiscence that satisfactorily resolved without intervention. Upper eyelid laser resurfacing is effective and can be safely performed at the same time as upper blepharoplasty. This approach reduces or eliminates the need for medial incisions to address medial canthal skin redundancy and rhytidosis and it directly treats upper eyelid wrinkles on residual eyelid and infra-brow skin during blepharoplasty.

  2. Workability of coal seams in the Upper Silesian Coal Basin

    Energy Technology Data Exchange (ETDEWEB)

    Sikora, W; Fels, M; Soltysik, K

    1978-04-01

    This paper presents results of an investigation on workability of coal seams of stratigraphic groups from 100 to 700 in the: Upper Silesian Coal Basin. Analyzed are 2900 petrographic logs taken in the longwall workings and in narrow openings as well as about 9000 individual samples. Workability of coal seams, floors and partings is determined. Workability is described by the indicator f, (according to the Protodyakonov shatter method) and the indicator U, (compression strength of the unshaped test samples). The mean percentage content of indivi dual petrographic groups of coal as well as the mean workability indicator, f, of coals in the stratigraphic groups of coal seams in Upper Silesia are also determined.

  3. Reflections on the present and future of upper limb prostheses.

    Science.gov (United States)

    Farina, Dario; Amsüss, Sebastian

    2016-01-01

    Despite progress in research and media attention on active upper limb prostheses, presently the most common commercial upper limb prosthetic devices are not fundamentally different from solutions offered almost one century ago. Limited information transfer for both control and sensory-motor integration and challenges in socket technology have been major obstacles. By analysing the present state-of-the-art and academic achievements, we provide our opinion on the future of upper limb prostheses. We believe that surgical procedures for muscle reinnervation and osseointegration will become increasingly clinically relevant; muscle electrical signals will remain the main clinical means for prosthetic control; and chronic electrode implants, first in muscles (control), then in nerves (sensory feedback), will become viable clinical solutions. After decades of suspended clinically relevant progress, it is foreseeable that a new generation of upper limb prostheses will enter the market in the near future based on such advances, thereby offering substantial clinical benefit for patients.

  4. Internalized Meaning Factualism

    DEFF Research Database (Denmark)

    Hohwy, Jakob

    2006-01-01

    The normative character of meaning creates deep problems for the attempt to give a reductive explanation of the constitution of meaning. I identify and critically examine an increasingly popular Carnap-style position, which I call Internalized Meaning Factualism (versions of which I argue...... are defended by, e.g., Robert Brandom, Paul Horwich and Huw Price), that promises to solve the problems. According to this position, the problem of meaning can be solved by prohibiting an external perspective on meaning constituting properties. The idea is that if we stick to a perspective on meaning...

  5. Oncoplastic Surgery for Upper/Upper Inner Quadrant Breast Cancer.

    Science.gov (United States)

    Lin, Joseph; Chen, Dar-Ren; Wang, Yu-Fen; Lai, Hung-Wen

    2016-01-01

    Tumors located in the upper/upper inner quadrant of the breast warrant more attention. A small lesion relative to the size of breast in this location may be resolved by performing a level I oncoplastic technique. However, a wide excision may significantly reduce the overall quality of the breast shape by distorting the visible breast line. From June 2012 to April 2015, 36 patients with breast cancer located in the upper/upper inner quadrant underwent breast-conservation surgery with matrix rotation mammoplasty. According to the size and location of the tumor relative to the nipple-areola complex, 11 patients underwent matrix rotation with periareolar de-epithelialization (donut group) and the other 25 underwent matrix rotation only (non-donut group). The cosmetic results were self-assessed by questionnaires. The average weights of the excised breast lumps in the donut and non-donut groups were 104.1 and 84.5 g, respectively. During the 3-year follow-up period, local recurrence was observed in one case and was managed with nipple-sparing mastectomy followed by breast reconstruction with prosthetic implants. In total, 31 patients (88.6%) ranked their postoperative result as either acceptable or satisfactory. The treated breasts were also self-evaluated by 27 patients (77.1%) to be nearly identical to or just slightly different from the untreated side. Matrix rotation is an easy breast-preserving technique for treating breast cancer located in the upper/upper inner quadrant of the breast that requires a relatively wide excision. With this technique, a larger breast tumor could be removed without compromising the breast appearance.

  6. Oncoplastic Surgery for Upper/Upper Inner Quadrant Breast Cancer.

    Directory of Open Access Journals (Sweden)

    Joseph Lin

    Full Text Available Tumors located in the upper/upper inner quadrant of the breast warrant more attention. A small lesion relative to the size of breast in this location may be resolved by performing a level I oncoplastic technique. However, a wide excision may significantly reduce the overall quality of the breast shape by distorting the visible breast line. From June 2012 to April 2015, 36 patients with breast cancer located in the upper/upper inner quadrant underwent breast-conservation surgery with matrix rotation mammoplasty. According to the size and location of the tumor relative to the nipple-areola complex, 11 patients underwent matrix rotation with periareolar de-epithelialization (donut group and the other 25 underwent matrix rotation only (non-donut group. The cosmetic results were self-assessed by questionnaires. The average weights of the excised breast lumps in the donut and non-donut groups were 104.1 and 84.5 g, respectively. During the 3-year follow-up period, local recurrence was observed in one case and was managed with nipple-sparing mastectomy followed by breast reconstruction with prosthetic implants. In total, 31 patients (88.6% ranked their postoperative result as either acceptable or satisfactory. The treated breasts were also self-evaluated by 27 patients (77.1% to be nearly identical to or just slightly different from the untreated side. Matrix rotation is an easy breast-preserving technique for treating breast cancer located in the upper/upper inner quadrant of the breast that requires a relatively wide excision. With this technique, a larger breast tumor could be removed without compromising the breast appearance.

  7. Portable upper extremity robotics is as efficacious as upper extremity rehabilitative therapy: a randomized controlled pilot trial.

    Science.gov (United States)

    Page, Stephen J; Hill, Valerie; White, Susan

    2013-06-01

    To compare the efficacy of a repetitive task-specific practice regimen integrating a portable, electromyography-controlled brace called the 'Myomo' versus usual care repetitive task-specific practice in subjects with chronic, moderate upper extremity impairment. Sixteen subjects (7 males; mean age 57.0 ± 11.02 years; mean time post stroke 75.0 ± 87.63 months; 5 left-sided strokes) exhibiting chronic, stable, moderate upper extremity impairment. Subjects were administered repetitive task-specific practice in which they participated in valued, functional tasks using their paretic upper extremities. Both groups were supervised by a therapist and were administered therapy targeting their paretic upper extremities that was 30 minutes in duration, occurring 3 days/week for eight weeks. One group participated in repetitive task-specific practice entirely while wearing the portable robotic, while the other performed the same activity regimen manually. The upper extremity Fugl-Meyer, Canadian Occupational Performance Measure and Stroke Impact Scale were administered on two occasions before intervention and once after intervention. After intervention, groups exhibited nearly identical Fugl-Meyer score increases of ≈2.1 points; the group using robotics exhibited larger score changes on all but one of the Canadian Occupational Performance Measure and Stroke Impact Scale subscales, including a 12.5-point increase on the Stroke Impact Scale recovery subscale. Findings suggest that therapist-supervised repetitive task-specific practice integrating robotics is as efficacious as manual practice in subjects with moderate upper extremity impairment.

  8. Means on scattered compacta

    Directory of Open Access Journals (Sweden)

    Banakh T.

    2014-01-01

    Full Text Available We prove that a separable Hausdor_ topological space X containing a cocountable subset homeomorphic to [0, ω1] admits no separately continuous mean operation and no diagonally continuous n-mean for n ≥ 2.

  9. Implementing statistical analysis in multi-channel acoustic impact-echo testing of concrete bridge decks: Determining thresholds for delamination detection

    Science.gov (United States)

    Hendricks, Lorin; Spencer Guthrie, W.; Mazzeo, Brian

    2018-04-01

    An automated acoustic impact-echo testing device with seven channels has been developed for faster surveying of bridge decks. Due to potential variations in bridge deck overlay thickness, varying conditions between testing passes, and occasional imprecise equipment calibrations, a method that can account for variations in deck properties and testing conditions was necessary to correctly interpret the acoustic data. A new methodology involving statistical analyses was therefore developed. After acoustic impact-echo data are collected and analyzed, the results are normalized by the median for each channel, a Gaussian distribution is fit to the histogram of the data, and the Kullback-Leibler divergence test or Otsu's method is then used to determine the optimum threshold for differentiating between intact and delaminated concrete. The new methodology was successfully applied to individual channels of previously unusable acoustic impact-echo data obtained from a three-lane interstate bridge deck surfaced with a polymer overlay, and the resulting delamination map compared very favorably with the results of a manual deck sounding survey.

  10. System for synthetic vision and augmented reality in future flight decks

    Science.gov (United States)

    Behringer, Reinhold; Tam, Clement K.; McGee, Joshua H.; Sundareswaran, Venkataraman; Vassiliou, Marius S.

    2000-06-01

    Rockwell Science Center is investigating novel human-computer interface techniques for enhancing the situational awareness in future flight decks. One aspect is to provide intuitive displays which provide the vital information and the spatial awareness by augmenting the real world with an overlay of relevant information registered to the real world. Such Augmented Reality (AR) techniques can be employed during bad weather scenarios to permit flying in Visual Flight Rules (VFR) in conditions which would normally require Instrumental Flight Rules (IFR). These systems could easily be implemented on heads-up displays (HUD). The advantage of AR systems vs. purely synthetic vision (SV) systems is that the pilot can relate the information overlay to real objects in the world, whereas SV systems provide a constant virtual view, where inconsistencies can hardly be detected. The development of components for such a system led to a demonstrator implemented on a PC. A camera grabs video images which are overlaid with registered information, Orientation of the camera is obtained from an inclinometer and a magnetometer, position is acquired from GPS. In a possible implementation in an airplane, the on-board attitude information can be used for obtaining correct registration. If visibility is sufficient, computer vision modules can be used to fine-tune the registration by matching visual clues with database features. Such technology would be especially useful for landing approaches. The current demonstrator provides a frame-rate of 15 fps, using a live video feed as background and an overlay of avionics symbology in the foreground. In addition, terrain rendering from a 1 arc sec. digital elevation model database can be overlaid to provide synthetic vision in case of limited visibility. For true outdoor testing (on ground level), the system has been implemented on a wearable computer.

  11. NextGen Flight Deck Surface Trajectory-Based Operations (STBO): Contingency Holds

    Science.gov (United States)

    Bakowski, Deborah Lee; Hooey, Becky Lee; Foyle, David C.; Wolter, Cynthia A.; Cheng, Lara W. S.

    2013-01-01

    The purpose of this pilot-in-the-loop taxi simulation was to investigate a NextGen Surface Trajectory-Based Operations (STBO) concept called "contingency holds." The contingency-hold concept parses a taxi route into segments, allowing an air traffic control (ATC) surface traffic management (STM) system to hold an aircraft when necessary for safety. Under nominal conditions, if the intersection or active runway crossing is clear, the hold is removed, allowing the aircraft to continue taxiing without slowing, thus improving taxi efficiency, while minimizing the excessive brake use, fuel burn, and emissions associated with stop-and-go taxi. However, when a potential traffic conflict exists, the hold remains in place as a fail-safe mechanism. In this departure operations simulation, the taxi clearance included a required time of arrival (RTA) to a specified intersection. The flight deck was equipped with speed-guidance avionics to aid the pilot in safely meeting the RTA. On two trials, the contingency hold was not released, and pilots were required to stop. On two trials the contingency hold was released 15 sec prior to the RTA, and on two trials the contingency hold was released 30 sec prior to the RTA. When the hold remained in place, all pilots complied with the hold. Results also showed that when the hold was released at 15-sec or 30-sec prior to the RTA, the 30-sec release allowed pilots to maintain nominal taxi speed, thus supporting continuous traffic flow; whereas, the 15-sec release did not. The contingency-hold concept, with at least a 30-sec release, allows pilots to improve taxiing efficiency by reducing braking, slowing, and stopping, but still maintains safety in that no pilots "busted" the clearance holds. Overall, the evidence suggests that the contingency-hold concept is a viable concept for optimizing efficiency while maintaining safety.

  12. Evaluation of Flight Deck-Based Interval Management Crew Procedure Feasibility

    Science.gov (United States)

    Wilson, Sara R.; Murdoch, Jennifer L.; Hubbs, Clay E.; Swieringa, Kurt A.

    2013-01-01

    Air traffic demand is predicted to increase over the next 20 years, creating a need for new technologies and procedures to support this growth in a safe and efficient manner. The National Aeronautics and Space Administration's (NASA) Air Traffic Management Technology Demonstration - 1 (ATD-1) will operationally demonstrate the feasibility of efficient arrival operations combining ground-based and airborne NASA technologies. The integration of these technologies will increase throughput, reduce delay, conserve fuel, and minimize environmental impacts. The ground-based tools include Traffic Management Advisor with Terminal Metering for precise time-based scheduling and Controller Managed Spacing decision support tools for better managing aircraft delay with speed control. The core airborne technology in ATD-1 is Flight deck-based Interval Management (FIM). FIM tools provide pilots with speed commands calculated using information from Automatic Dependent Surveillance - Broadcast. The precise merging and spacing enabled by FIM avionics and flight crew procedures will reduce excess spacing buffers and result in higher terminal throughput. This paper describes a human-in-the-loop experiment designed to assess the acceptability and feasibility of the ATD-1 procedures used in a voice communications environment. This experiment utilized the ATD-1 integrated system of ground-based and airborne technologies. Pilot participants flew a high-fidelity fixed base simulator equipped with an airborne spacing algorithm and a FIM crew interface. Experiment scenarios involved multiple air traffic flows into the Dallas-Fort Worth Terminal Radar Control airspace. Results indicate that the proposed procedures were feasible for use by flight crews in a voice communications environment. The delivery accuracy at the achieve-by point was within +/- five seconds and the delivery precision was less than five seconds. Furthermore, FIM speed commands occurred at a rate of less than one per minute

  13. Rolling Deck to Repository II: Getting Control of Provenance and Quality

    Science.gov (United States)

    Miller, S. P.; Arko, R.; Chandler, C. L.; Clark, P. D.; Neiswender, C.

    2008-12-01

    Data are now being re-used by a far wider circle of researchers and students than ever before, across a broader range of disciplines. Before, during, and after a field program, the exchange and merging of information is a dynamic, iterative and sometimes anonymous process that may occur years, or decades, after the data were initially acquired. Collaborative steps are currently being taken toward a prototype data discovery system that can be extended to the entire NSF-supported academic research fleet, including both large and small operations. With emerging shipboard Internet capabilities, near real-time transport of selected data from the rolling deck to a repository can become a reality. Much of the effort is being devoted to data preservation and access, to the identification of standard products, and to the generation of appropriate metadata, with a streamlined methodology that can be adopted by a wide range of vessel operating institutions. Beyond the challenge of just finding data, currently researchers and students struggle repeatedly to make sense of downloaded data objects. Across institutions there are wide variations in quality control procedures, most commonly none, and virtually no external communication of the history of transformations applied to a data set. For example, the status of corrections for sound velocity or roll-bias, or beampoint editing for multibeam swath seafloor mapping sonar systems are often challenging to experts and baffling to users from other disciplines. With greater re-use of data comes the greater likelihood of interpretation of artifacts as features. Tracking data provenance and quality is a problem today, and the situation will become more critical as data are more widely and rapidly disseminated. We will identify quality control criteria for standard shipboard data products, and existing tools for quality assessment with automation potential (or lack thereof). We invite discussion of an XML institutional quality

  14. Rolling Deck to Repository (R2R): Collaborative Development of Linked Data for Oceanographic Research

    Science.gov (United States)

    Arko, Robert; Chandler, Cynthia; Stocks, Karen; Smith, Shawn; Clark, Paul; Shepherd, Adam; Moore, Carla; Beaulieu, Stace

    2013-04-01

    The Rolling Deck to Repository (R2R) program is developing infrastructure to ensure the underway sensor data from U.S. academic oceanographic research vessels are routinely and consistently documented, preserved in long-term archives, and disseminated to the science community. The entire R2R Catalog is published online as a Linked Data collection, making it easily accessible to encourage discovery and integration with data at other repositories. We are developing the R2R Linked Data collection with specific goals in mind: 1.) We facilitate data access and reuse by publishing the richest possible collection of resources to describe vessels, cruises, instruments, and datasets from the U.S. academic fleet, including data quality assessment results and clean trackline navigation; 2.) We facilitate data citation through the entire lifecycle from field acquisition to shoreside archiving to journal articles and global syntheses, by publishing Digital Object Identifiers (DOIs) for datasets and encoding them directly into our Linked Data resources; and 3.) We facilitate federation with other repositories such as the Biological and Chemical Oceanography Data Management Office (BCO-DMO), InterRidge Vents Database, and Index to Marine and Lacustrine Geological Samples (IMLGS), by reciprocal linking between RDF resources and supporting the RDF Query Language. R2R participates in the Ocean Data Interoperability Platform (ODIP), a joint European-U.S.-Australian partnership to facilitate the sharing of data and documentation across international borders. We publish our controlled vocabularies as a Simple Knowledge Organization System (SKOS) concept collection, and are working toward alignment with SeaDataNet and other community-standard terms using the NERC Vocabulary Server (NVS). http://rvdata.us/

  15. Upper atmosphere research at INPE

    International Nuclear Information System (INIS)

    Clemesha, B.R.

    1984-01-01

    Upper atmosphere research at INPE is mainly concerned with the chemistry and dynamics of the stratosphere, upper mesosphere and lower thermosphere, and the middle thermosphere. Experimental work includes lidar observations of the stratospheric aerosol, measurements of stratospheric ozone by Dobson spectrophotometers and by balloon and rocket-borne sondes, lidar measurements of atmospheric sodium, and photometric observations of O, O 2 , OH and Na emissions, including interferrometric measurements of the OI6300 emission for the purpose of determing thermospheric winds and temperature. The airglow observations also include measurements of a number of emissions produced by the precipitation of energetic neutral particles generated by charge exchange in the ring current. Some recent results of INPE's upper atmosphere program are presented. (Author) [pt

  16. Combustion means for solid fuels

    Energy Technology Data Exchange (ETDEWEB)

    Murase, D.

    1987-09-23

    A combustion device for solid fuel, suitable for coal, coke, charcoal, coal-dust briquettes etc., comprising:- a base stand with an opening therein, an imperforate heat resistant holding board locatable to close said opening; a combustion chamber standing on the base stand with the holding board forming the base of the combustion chamber; a wiper arm pivoted for horizontal wiping movement over the upper surface of the holding board; an inlet means at a lower edge of said chamber above the base stand, and/or in a surrounding wall of said chamber, whereby combustion air may enter as exhaust gases leave the combustion chamber; an exhaust pipe for the exhaust gases; generally tubular gas-flow heat-exchange ducting putting the combustion chamber and exhaust pipe into communication; and means capable of moving the holding board into and out of the opening for removal of ash or other residue. The invention can be used for a heating system in a house or in a greenhouse or for a boiler.

  17. Meaning in mathematics education

    CERN Document Server

    Valero, Paola; Hoyles, Celia; Skovsmose, Ole

    2005-01-01

    What does it mean to know mathematics? How does meaning in mathematics education connect to common sense or to the meaning of mathematics itself? How are meanings constructed and communicated and what are the dilemmas related to these processes? There are many answers to these questions, some of which might appear to be contradictory. Thus understanding the complexity of meaning in mathematics education is a matter of huge importance. There are twin directions in which discussions have developed - theoretical and practical - and this book seeks to move the debate forward along both dimensions while seeking to relate them where appropriate. A discussion of meaning can start from a theoretical examination of mathematics and how mathematicians over time have made sense of their work. However, from a more practical perspective, anybody involved in teaching mathematics is faced with the need to orchestrate the myriad of meanings derived from multiple sources that students develop of mathematical knowledge.

  18. Arch-Axis Coefficient Optimization of Long-Span Deck-Type Concrete-Filled Steel Tubular Arch Bridge

    Science.gov (United States)

    Liu, Q. J.; Wan, S.; Liu, H. C.

    2017-11-01

    This paper is based on Nanpuxi super major bridge which is under construction and starts from Wencheng Zhejiang province to Taishun highway. A finite element model of the whole bridge is constructed using Midas Civil finite element software. The most adverse load combination in the specification is taken into consideration to determine the method of calculating the arch-axis coefficient of long-span deck-type concrete-filled steel tubular arch bridge. By doing this, this paper aims at providing references for similar engineering projects.

  19. Music, Meaning and Culture

    Directory of Open Access Journals (Sweden)

    Richard Widdess

    2012-09-01

    Full Text Available This paper situates musical meaning in culture, addressing music as social symbol and as ongoing process of meaning creation. Three examples of non- Western musical practice are used to illustrate the embedding of musical meaning in cultural context. The performance of an Australian Aboriginal song is shown to exemplify the interdependence of song style and social structure as a matrix for the emergence of cultural meanings; an example of North Indian performance is adduced to demonstrate the multi-layered nature of meaning as embodied in musical performance; and an example of collective festival performance from Nepal illustrates ways in which the structure of musical performance can mirror local cultural forms. Each of the three examples lends weight to the idea that music's meanings are often non-linguistic and reflect foundational schemas that are specific to the cultures from the musics are drawn.

  20. Brand Meaning Cocreation

    DEFF Research Database (Denmark)

    Tierney, Kieran D.; Karpen, Ingo; Westberg, Kate

    2016-01-01

    Purpose: The purpose of this paper is to consolidate and advance the understanding of brand meaning and the evolving process by which it is determined by introducing and explicating the concept of brand meaning cocreation (BMCC). Design/methodology/approach: In-depth review and integration...... of literature from branding, cocreation, service systems, and practice theory. To support deep theorizing, the authors also examine the role of institutional logics in the BMCC process in framing interactions and brand meaning outcomes. Findings: Prior research is limited in that it neither maps the process...... of cocreation within which meanings emerge nor provides theoretical conceptualizations of brand meaning or the process of BMCC. While the literature acknowledges that brand meaning is influenced by multiple interactions, their nature and how they contribute to BMCC have been overlooked. Research limitations...

  1. Active Upper-atmosphere Chemistry and Dynamics from Polar Circulation Reversal on Titan

    Science.gov (United States)

    Teanby, Nicholas A.; Irwin, Patrick Gerard Joseph; Nixon, Conor A.; DeKok, Remco; Vinatier, Sandrine; Coustenis, Athena; Sefton-Nash, Elliot; Calcutt, Simon B.; Flasar, Michael F.

    2012-01-01

    Saturn's moon Titan has a nitrogen atmosphere comparable to Earth's, with a surface pressure of 1.4 bar. Numerical models reproduce the tropospheric conditions very well but have trouble explaining the observed middle-atmosphere temperatures, composition and winds. The top of the middle-atmosphere circulation has been thought to lie at an altitude of 450 to 500 kilometres, where there is a layer of haze that appears to be separated from the main haze deck. This 'detached' haze was previously explained as being due to the colocation of peak haze production and the limit of dynamical transport by the circulation's upper branch. Herewe report a build-up of trace gases over the south pole approximately two years after observing the 2009 post-equinox circulation reversal, from which we conclude that middle-atmosphere circulation must extend to an altitude of at least 600 kilometres. The primary drivers of this circulation are summer-hemisphere heating of haze by absorption of solar radiation and winter-hemisphere cooling due to infrared emission by haze and trace gases; our results therefore imply that these effects are important well into the thermosphere (altitudes higher than 500 kilometres). This requires both active upper-atmosphere chemistry, consistent with the detection of high-complexity molecules and ions at altitudes greater than 950 kilometres, and an alternative explanation for the detached haze, such as a transition in haze particle growth from monomers to fractal structures.

  2. Upper limb movement analysis during gait in multiple sclerosis patients.

    Science.gov (United States)

    Elsworth-Edelsten, Charlotte; Bonnefoy-Mazure, Alice; Laidet, Magali; Armand, Stephane; Assal, Frederic; Lalive, Patrice; Allali, Gilles

    2017-08-01

    Gait disorders in multiple sclerosis (MS) are well studied; however, no previous study has described upper limb movements during gait. However, upper limb movements have an important role during locomotion and can be altered in MS patients due to direct MS lesions or mechanisms of compensation. The aim of this study was to describe the arm movements during gait in a population of MS patients with low disability compared with a healthy control group. In this observational study we analyzed the arm movements during gait in 52 outpatients (mean age: 39.7±9.6years, female: 40%) with relapsing-remitting MS with low disability (mean EDSS: 2±1) and 25 healthy age-matched controls using a 3-dimension gait analysis. MS patients walked slower, with increased mean elbow flexion and decreased amplitude of elbow flexion (ROM) compared to the control group, whereas shoulder and hand movements were similar to controls. These differences were not explained by age or disability. Upper limb alterations in movement during gait in MS patients with low disability can be characterized by an increase in mean elbow flexion and a decrease in amplitude (ROM) for elbow flexion/extension. This upper limb movement pattern should be considered as a new component of gait disorders in MS and may reflect subtle motor deficits or the use of compensatory mechanisms. Copyright © 2017 Elsevier B.V. All rights reserved.

  3. Upper Limit in the Periodic Table of Elements

    Directory of Open Access Journals (Sweden)

    Khazan A.

    2007-01-01

    Full Text Available The method of rectangular hyperbolas is developed for the first time, by which a means for estimating the upper bound of the Periodic Table is established in calculating that its last element has an atom mass of 411.663243 and an atomic number (the nuclear charge of 155. The formulating law is given.

  4. Teaching Introductory Upper-Level Religion and Theology Classes

    Science.gov (United States)

    Clingerman, Forrest; O'Brien, Kevin J.

    2015-01-01

    The undergraduate study of religion is predominantly undertaken by non-majors who are meeting a general education requirement. This means that, while curricular discussions make important distinctions between the work of lower- and upper-division courses, many religion and theology faculty are teaching hybrid courses that we call…

  5. Angiography of the upper extremity

    International Nuclear Information System (INIS)

    Janevski, B.K.

    1982-01-01

    This thesis provides a description of the technical and medical aspects of arteriography of the upper extremity and an extensive analysis of the angiographic anatomy and pathology of 750 selective studies performed in more than 500 patients. A short historical review is provided of angiography as a whole and of arteriography of the hand in particular. The method of percutaneous transfemoral catheterization of the arteries of the upper extremity and particularly the arteries of the hand is considered, discussing the problems the angiographer encounters frequently, describing the angiographic complications which may occur and emphasizing the measures to keep them to a minimum. The use of vasodilators in hand angiography is discussed. A short description of the embryological patterns persisting in the arteries of the arm is included in order to understand the congenital variations of the arteries of the upper extremity. The angiographic patterns and clinical aspects of the most common pathological processes involving the arteries of the upper extremities are presented. Special attention is paid to the correlation between angiography and pathology. (Auth.)

  6. Approach to upper gastrointestinal bleeding

    African Journals Online (AJOL)

    Upper gastrointestinal haemorrhage has a variety of causes (Table 1) and is the commonest complication of peptic ulceration and portal hypertension. Peptic ulceration in the duo- denum or stomach and oesophageal varices are the conditions most often responsible for patients who have the potential to present.

  7. Horizontal Diplopia Following Upper Blepharoplasty

    Directory of Open Access Journals (Sweden)

    Tomás Ortiz-Basso

    2014-09-01

    Full Text Available Diplopia is an infrequent complication after blepharoplasty. Most of the cases are in its vertical form due to trauma of the extraocular muscles. In this article, we present a case of horizontal diplopia following cosmetic upper blepharoplasty; we review the literature on this unexpected complication and offer some recommendations to avoid it.

  8. Agency, Context and Meaning

    DEFF Research Database (Denmark)

    Folkmann, Mads Nygaard

    2014-01-01

    The paper is a meta-discursive contribution to the discussion of how design can be understood as a medium of meaning formation and questioning of meaning. Further, the paper builds on plea for the role of humanities in relation to formulate relevant questions in design through conceptualizing the...... of meaning formulation and cultural contexts and, by this, contest design. In reflecting the foundational ground of design in terms of its agency, contexts and meaning constituents, design and its questioning of meaning can be critically reframed.......The paper is a meta-discursive contribution to the discussion of how design can be understood as a medium of meaning formation and questioning of meaning. Further, the paper builds on plea for the role of humanities in relation to formulate relevant questions in design through conceptualizing...... history, 2) the question of context in and of design, i.e. which contexts give meaning to design; this question calls for interpretive models of cultural analysis of the circuit of design in acknowledging phases and aspects of production, mediation and consumption, and 3) the question of the meaning...

  9. Parallel k-means++

    Energy Technology Data Exchange (ETDEWEB)

    2017-04-04

    A parallelization of the k-means++ seed selection algorithm on three distinct hardware platforms: GPU, multicore CPU, and multithreaded architecture. K-means++ was developed by David Arthur and Sergei Vassilvitskii in 2007 as an extension of the k-means data clustering technique. These algorithms allow people to cluster multidimensional data, by attempting to minimize the mean distance of data points within a cluster. K-means++ improved upon traditional k-means by using a more intelligent approach to selecting the initial seeds for the clustering process. While k-means++ has become a popular alternative to traditional k-means clustering, little work has been done to parallelize this technique. We have developed original C++ code for parallelizing the algorithm on three unique hardware architectures: GPU using NVidia's CUDA/Thrust framework, multicore CPU using OpenMP, and the Cray XMT multithreaded architecture. By parallelizing the process for these platforms, we are able to perform k-means++ clustering much more quickly than it could be done before.

  10. A 12 years audit of upper gastrointestinal endoscopic procedures

    International Nuclear Information System (INIS)

    Khurram, M.; Khaar, H.B.; Hasan, Z.; Umar, M.; Javed, S.; Asghar, T.; Minhas, Z.; Akbar, A.; Atta, N.; Nassar, F.; Sultana, Q.; Pervaiz, A.; Masoom, A.

    2003-01-01

    Objective: Evaluation of upper gastrointestinal (GI) endoscopy in terms of indications, diagnostic efficacy, and diseases diagnosed. Results: Of the 8481 patients, 4935 (58.2%) were female and 3546 (41.8%) male. Mean patient age was 40.5 years. Dyspepsia (42.6%), upper GI bleed (32.8%), and evaluation of chronic liver disease (10.2%) were common indications of the procedure. An endoscopic diagnosis was possible in 82.6% patients. Varices, gastritis, duodenitis, and combined lesions were common endoscopic diagnosis. Gastritis and duodenitis were most frequent causes of upper GI bleed. We noted more gastric ulcers compared to duodenal ulcers. Females had significantly more normal endoscopies, p-value = 0.02. Conclusion: Upper GI endoscopy is an effective procedure. Dyspepsia evaluation is commonest indication for upper GI endoscopy in our patients. Etiology of upper GI bleed, and incidence of duodenal ulcer compared to gastric ulcer in our patients are different than described in literature. Females have significantly more normal endoscopies. (author)

  11. Wind-Tunnel Investigation of Wind Loads on a Post-Panamax Container Ship as a Function of the Container Configuration on Deck

    DEFF Research Database (Denmark)

    Andersen, Ingrid Marie Vincent

    2012-01-01

    An investigation of the wind forces acting on a 9,000+ TEU container ship has been carried out through a series of wind tunnel tests. It was investigated how the wind forces depend on the container configuration on the deck using a 1:450 scale model and a series of appropriate container...... are presented as nondimensional coefficients. It is concluded, that the measured forces and moment depend on the container configuration on deck, and the results may provide a general idea of how the magnitude of the wind forces is affected by a given container stacking configuration on a similar container ship....

  12. Mean field games

    KAUST Repository

    Gomes, Diogo A.

    2014-01-06

    In this talk we will report on new results concerning the existence of smooth solutions for time dependent mean-field games. This new result is established through a combination of various tools including several a-priori estimates for time-dependent mean-field games combined with new techniques for the regularity of Hamilton-Jacobi equations.

  13. Phenomenology and Meaning Attribution

    African Journals Online (AJOL)

    John Paley. (2017). Phenomenology as Qualitative Research: A Critical Analysis of Meaning Attribution. ... basic philosophical nature of phenomenological meaning and inquiry, and that he not ... In keeping with the title of my book, Researching. Lived Experience ...... a quantitative social science that can make generalizing.

  14. Mean field games

    KAUST Repository

    Gomes, Diogo A.

    2014-01-01

    In this talk we will report on new results concerning the existence of smooth solutions for time dependent mean-field games. This new result is established through a combination of various tools including several a-priori estimates for time-dependent mean-field games combined with new techniques for the regularity of Hamilton-Jacobi equations.

  15. Quantized kernel least mean square algorithm.

    Science.gov (United States)

    Chen, Badong; Zhao, Songlin; Zhu, Pingping; Príncipe, José C

    2012-01-01

    In this paper, we propose a quantization approach, as an alternative of sparsification, to curb the growth of the radial basis function structure in kernel adaptive filtering. The basic idea behind this method is to quantize and hence compress the input (or feature) space. Different from sparsification, the new approach uses the "redundant" data to update the coefficient of the closest center. In particular, a quantized kernel least mean square (QKLMS) algorithm is developed, which is based on a simple online vector quantization method. The analytical study of the mean square convergence has been carried out. The energy conservation relation for QKLMS is established, and on this basis we arrive at a sufficient condition for mean square convergence, and a lower and upper bound on the theoretical value of the steady-state excess mean square error. Static function estimation and short-term chaotic time-series prediction examples are presented to demonstrate the excellent performance.

  16. Rolling Deck to Repository (R2R): Standards and Semantics for Open Access to Research Data

    Science.gov (United States)

    Arko, Robert; Carbotte, Suzanne; Chandler, Cynthia; Smith, Shawn; Stocks, Karen

    2015-04-01

    In recent years, a growing number of funding agencies and professional societies have issued policies calling for open access to research data. The Rolling Deck to Repository (R2R) program is working to ensure open access to the environmental sensor data routinely acquired by the U.S. academic research fleet. Currently 25 vessels deliver 7 terabytes of data to R2R each year, acquired from a suite of geophysical, oceanographic, meteorological, and navigational sensors on over 400 cruises worldwide. R2R is working to ensure these data are preserved in trusted repositories, discoverable via standard protocols, and adequately documented for reuse. R2R maintains a master catalog of cruises for the U.S. academic research fleet, currently holding essential documentation for over 3,800 expeditions including vessel and cruise identifiers, start/end dates and ports, project titles and funding awards, science parties, dataset inventories with instrument types and file formats, data quality assessments, and links to related content at other repositories. A Digital Object Identifier (DOI) is published for 1) each cruise, 2) each original field sensor dataset, 3) each post-field data product such as quality-controlled shiptrack navigation produced by the R2R program, and 4) each document such as a cruise report submitted by the science party. Scientists are linked to personal identifiers, such as the Open Researcher and Contributor ID (ORCID), where known. Using standard global identifiers such as DOIs and ORCIDs facilitates linking with journal publications and generation of citation metrics. Since its inception, the R2R program has worked in close collaboration with other data repositories in the development of shared semantics for oceanographic research. The R2R cruise catalog uses community-standard terms and definitions hosted by the NERC Vocabulary Server, and publishes ISO metadata records for each cruise that use community-standard profiles developed with the NOAA Data

  17. Rolling Deck to Repository (R2R): Technical Design - Experiences and Lessons (Invited)

    Science.gov (United States)

    Arko, R. A.; Carbotte, S. M.; Miller, S. P.; Chandler, C. L.; Ferrini, V.; Stocks, K.; Maffei, A. R.; Smith, S. R.; Bourassa, M. A.; McLean, S. J.; Alberts, J. C.

    2009-12-01

    The NSF-funded Rolling Deck to Repository (R2R) project envisions the academic research fleet as an integrated global observing system, with routine “underway” sensor data flowing directly from research vessels to a central shore-side repository. It is a complex endeavor involving many stakeholders - technicians at sea, data managers on shore, ship schedulers, clearance officers, funding agencies, National Data Centers, data synthesis projects, the science community, and the public - working toward a common goal of acquiring, documenting, archiving, evaluating, and disseminating high-quality scientific data. The technical design for R2R is guided by several key principles: 1) The data pipeline is modular, so that initial stages (e.g. inventory and review of data shipments, posting of catalog records and track maps) may proceed routinely for every cruise, while later stages (e.g. quality assessment and production of file-level metadata) may proceed at different rates for different data types; 2) Cruise documentation (e.g. sailing orders, review/release of data inventories, vessel profiles) is gathered primarily via an authenticated Web portal, linked with the UNOLS scheduling database to synchronize vocabularies and eliminate redundancies; and 3) Every data set will be documented and delivered to the appropriate National Data Center for long-term archiving and dissemination after proprietary holds are cleared, while R2R maintains a master cruise catalog that links all the data sets together. This design accommodates the diversity of instrument types, data volumes, and shipment schedules among fleet operators. During its pilot development period, R2R has solicited feedback at community workshops, UNOLS meetings, and conference presentations, including fleet-wide surveys of current practices and instrument inventories. Several vessel operators began submitting cruise data and documentation during the pilot, providing a test bed for database development and Web

  18. Rolling Deck to Repository (R2R): Linking and Integrating Data for Oceanographic Research

    Science.gov (United States)

    Arko, R. A.; Chandler, C. L.; Clark, P. D.; Shepherd, A.; Moore, C.

    2012-12-01

    The Rolling Deck to Repository (R2R) program is developing infrastructure to ensure the underway sensor data from NSF-supported oceanographic research vessels are routinely and consistently documented, preserved in long-term archives, and disseminated to the science community. We have published the entire R2R Catalog as a Linked Data collection, making it easily accessible to encourage linking and integration with data at other repositories. We are developing the R2R Linked Data collection with specific goals in mind: 1.) We facilitate data access and reuse by providing the richest possible collection of resources to describe vessels, cruises, instruments, and datasets from the U.S. academic fleet, including data quality assessment results and clean trackline navigation. We are leveraging or adopting existing community-standard concepts and vocabularies, particularly concepts from the Biological and Chemical Oceanography Data Management Office (BCO-DMO) ontology and terms from the pan-European SeaDataNet vocabularies, and continually re-publish resources as new concepts and terms are mapped. 2.) We facilitate data citation through the entire data lifecycle from field acquisition to shoreside archiving to (ultimately) global syntheses and journal articles. We are implementing globally unique and persistent identifiers at the collection, dataset, and granule levels, and encoding these citable identifiers directly into the Linked Data resources. 3.) We facilitate linking and integration with other repositories that publish Linked Data collections for the U.S. academic fleet, such as BCO-DMO and the Index to Marine and Lacustrine Geological Samples (IMLGS). We are initially mapping datasets at the resource level, and plan to eventually implement rule-based mapping at the concept level. We work collaboratively with partner repositories to develop best practices for URI patterns and consensus on shared vocabularies. The R2R Linked Data collection is implemented as a

  19. Rolling Deck to Repository (R2R): Big Data and Standard Services for the Fleet Community

    Science.gov (United States)

    Arko, R. A.; Carbotte, S. M.; Chandler, C. L.; Smith, S. R.; Stocks, K. I.

    2014-12-01

    The Rolling Deck to Repository (R2R; http://rvdata.us/) program curates underway environmental sensor data from the U.S. academic oceanographic research fleet, ensuring data sets are routinely and consistently documented, preserved in long-term archives, and disseminated to the science community. Currently 25 in-service vessels contribute 7 terabytes of data to R2R each year, acquired from a full suite of geophysical, oceanographic, meteorological, and navigational sensors on over 400 cruises worldwide. To accommodate this large volume and variety of data, R2R has developed highly efficient stewardship procedures. These include scripted "break out" of cruise data packages from each vessel based on standard filename and directory patterns; automated harvest of cruise metadata from the UNOLS Office via Web Services and from OpenXML-based forms submitted by vessel operators; scripted quality assessment routines that calculate statistical summaries and standard ratings for selected data types; adoption of community-standard controlled vocabularies for vessel codes, instrument types, etc, provided by the NERC Vocabulary Server, in lieu of maintaining custom local term lists; and a standard package structure based on the IETF BagIt format for delivering data to long-term archives. Documentation and standard post-field products, including quality-controlled shiptrack navigation data for every cruise, are published in multiple services and formats to satisfy a diverse range of clients. These include Catalog Service for Web (CSW), GeoRSS, and OAI-PMH discovery services via a GeoNetwork portal; OGC Web Map and Feature Services for GIS clients; a citable Digital Object Identifier (DOI) for each dataset; ISO 19115-2 standard geospatial metadata records suitable for submission to long-term archives as well as the POGO global catalog; and Linked Open Data resources with a SPARQL query endpoint for Semantic Web clients. R2R participates in initiatives such as the Ocean Data

  20. Comparing the performance of expert user heuristics and an integer linear program in aircraft carrier deck operations.

    Science.gov (United States)

    Ryan, Jason C; Banerjee, Ashis Gopal; Cummings, Mary L; Roy, Nicholas

    2014-06-01

    Planning operations across a number of domains can be considered as resource allocation problems with timing constraints. An unexplored instance of such a problem domain is the aircraft carrier flight deck, where, in current operations, replanning is done without the aid of any computerized decision support. Rather, veteran operators employ a set of experience-based heuristics to quickly generate new operating schedules. These expert user heuristics are neither codified nor evaluated by the United States Navy; they have grown solely from the convergent experiences of supervisory staff. As unmanned aerial vehicles (UAVs) are introduced in the aircraft carrier domain, these heuristics may require alterations due to differing capabilities. The inclusion of UAVs also allows for new opportunities for on-line planning and control, providing an alternative to the current heuristic-based replanning methodology. To investigate these issues formally, we have developed a decision support system for flight deck operations that utilizes a conventional integer linear program-based planning algorithm. In this system, a human operator sets both the goals and constraints for the algorithm, which then returns a proposed schedule for operator approval. As a part of validating this system, the performance of this collaborative human-automation planner was compared with that of the expert user heuristics over a set of test scenarios. The resulting analysis shows that human heuristics often outperform the plans produced by an optimization algorithm, but are also often more conservative.

  1. An Extended Flexible Job Shop Scheduling Model for Flight Deck Scheduling with Priority, Parallel Operations, and Sequence Flexibility

    Directory of Open Access Journals (Sweden)

    Lianfei Yu

    2017-01-01

    Full Text Available Efficient scheduling for the supporting operations of aircrafts in flight deck is critical to the aircraft carrier, and even several seconds’ improvement may lead to totally converse outcome of a battle. In the paper, we ameliorate the supporting operations of carrier-based aircrafts and investigate three simultaneous operation relationships during the supporting process, including precedence constraints, parallel operations, and sequence flexibility. Furthermore, multifunctional aircrafts have to take off synergistically and participate in a combat cooperatively. However, their takeoff order must be restrictively prioritized during the scheduling period accorded by certain operational regulations. To efficiently prioritize the takeoff order while minimizing the total time budget on the whole takeoff duration, we propose a novel mixed integer liner programming formulation (MILP for the flight deck scheduling problem. Motivated by the hardness of MILP, we design an improved differential evolution algorithm combined with typical local search strategies to improve computational efficiency. We numerically compare the performance of our algorithm with the classical genetic algorithm and normal differential evolution algorithm and the results show that our algorithm obtains better scheduling schemes that can meet both the operational relations and the takeoff priority requirements.

  2. Mean-periodic functions

    Directory of Open Access Journals (Sweden)

    Carlos A. Berenstein

    1980-01-01

    Full Text Available We show that any mean-periodic function f can be represented in terms of exponential-polynomial solutions of the same convolution equation f satisfies, i.e., u∗f=0(μ∈E′(ℝn. This extends to n-variables the work of L. Schwartz on mean-periodicity and also extends L. Ehrenpreis' work on partial differential equations with constant coefficients to arbitrary convolutors. We also answer a number of open questions about mean-periodic functions of one variable. The basic ingredient is our work on interpolation by entire functions in one and several complex variables.

  3. Meaning in Work Life

    DEFF Research Database (Denmark)

    Ravn, Ib

    meaningful is still lacking (Harpaz & Fu, 2002), as are definitions of key terms. Here, I define meaning as the experience that something fits into a wider context or coheres within a larger whole.     I conceptualize meaning in work life as deriving from four factors, each of which helps us contribute...... to something larger than ourselves (Seligman, 2002) through our work. Thus, a person experiences meaning in work life when she... A. is able to use her signature strengths at work (Peterson and Seligman, 2004), B. makes an important contribution to the workplace (Drucker, 1999), C. participates in a productive...

  4. The Upper Danube Nature Park

    International Nuclear Information System (INIS)

    Dosedla, H.C.

    1997-01-01

    When in 1980 the Upper Danube Nature Park was founded as one of 65 nature sanctuaries in Germany there was great diversity of opinions concerning its intended character. The protected region consisting of a geologically outstanding landscape within central Europe is covering the first 80 km the upper Danube where the young river shortly after it's source in the Black Forest is breaking through the narrow canyons of the Jurassic rock plateau of the so-called Suebian Alps and also locates the subterranean passage where the stream is submerging from the surface for nearly ten miles. Since the purpose of nature preservation according to German las is closely combined with the rather contradicting aim of offering an attractive recreation area thus facing the immense impacts of modern mass tourism there are numerous problems which in the course of years have resulted in an intricate patterns of subtle management methods coping with the growing awareness of the ecological balance. (author)

  5. Mean nuclear volume

    DEFF Research Database (Denmark)

    Mogensen, O.; Sørensen, Flemming Brandt; Bichel, P.

    1999-01-01

    We evaluated the following nine parameters with respect to their prognostic value in females with endometrial cancer: four stereologic parameters [mean nuclear volume (MNV), nuclear volume fraction, nuclear index and mitotic index], the immunohistochemical expression of cancer antigen (CA125...

  6. Meaning in couples relationships.

    Directory of Open Access Journals (Sweden)

    Rodrigues T.F.

    2014-09-01

    Full Text Available Based on psycholinguistics and L. Vygotsky’s (2007 theories on sign, meaning and sense categories, as later discussed by A. Leontiev (2004, 2009, we present a case study that focuses on the intricacies of a love relationship for a woman who remained in a painful marriage. Interview material is presented in a Relational-Historical Psychology theoretical framework to provide central categories of meaning and sense. This is understood as a privileged method for apprehending the uniqueness of a human being. To segment the qualitative material, we used the “Analysis of the Nuclei of Meanings for the Apprehension of the Constitution of Sense,” by Aguiar and Ozella (2006, 2013. This approach seeks to discriminate the meanings and senses that constitute the content of a speech sample.

  7. Soils - Mean Permeability

    Data.gov (United States)

    Kansas Data Access and Support Center — This digital spatial data set provides information on the magnitude and spatial pattern of depth-weighted, mean soil permeability throughout the State of Kansas. The...

  8. Upper limit of peak area

    International Nuclear Information System (INIS)

    Helene, O.A.M.

    1982-08-01

    The determination of the upper limit of peak area in a multi-channel spectra, with a known significance level is discussed. This problem is specially important when the peak area is masked by the background statistical fluctuations. The problem is exactly solved and, thus, the results are valid in experiments with small number of events. The results are submitted to a Monte Carlo test and applied to the 92 Nb beta decay. (Author) [pt

  9. Meaning in Matter

    DEFF Research Database (Denmark)

    Brix, Anders

    2013-01-01

    When addressing present-day challenges, design discourse put faith mainly in design understood as a problem-solving activity, pertaining to innovation on functional, systems and technological level. The aesthetically founded fields, e.g. craft-based design, on the other hand, do not seem to play ...... - in particular those which carry _corporeal affordance_, such as clothing, blankets, chairs, tables and houses - perhaps even cities. Things that mean to us, what they mean, mainly _qua_ their physical properties....

  10. Stats means business

    CERN Document Server

    Buglear, John

    2010-01-01

    Stats Means Business is an introductory textbook written for Business, Hospitality and Tourism students who take modules on Statistics or Quantitative research methods. Recognising that most users of this book will have limited if any grounding in the subject, this book minimises technical language, provides clear definition of key terms, and gives emphasis to interpretation rather than technique.Stats Means Business enables readers to:appreciate the importance of statistical analysis in business, hospitality and tourism understand statis

  11. Temperature structure of the Uranian upper atmosphere

    Science.gov (United States)

    Elliot, J. L.; Dunham, E.

    1979-01-01

    The temperature structure of the upper atmosphere of Uranus at two locations on the planet was determined from observations of the occultation of the star SAO158687 by Uranus on 10 March 1977, carried out at the Kuiper Airborne Observatory. The temperature-pressure relationships obtained from the immersion and emersion data for 7280 A channel show peak-to-peak variations of 45 K for immersion and 35 K for emersion. The mean temperature for both immersion and emersion profiles is about 100 K, which shows that Uranus has a temperature inversion between 0.001 mbar and the 100 mbar level probed by IR measurements. Both profiles show wavelike temperature variations, which may be due to dynamical or photochemical processes.

  12. Technology improves upper extremity rehabilitation.

    Science.gov (United States)

    Kowalczewski, Jan; Prochazka, Arthur

    2011-01-01

    Stroke survivors with hemiparesis and spinal cord injury (SCI) survivors with tetraplegia find it difficult or impossible to perform many activities of daily life. There is growing evidence that intensive exercise therapy, especially when supplemented with functional electrical stimulation (FES), can improve upper extremity function, but delivering the treatment can be costly, particularly after recipients leave rehabilitation facilities. Recently, there has been a growing level of interest among researchers and healthcare policymakers to deliver upper extremity treatments to people in their homes using in-home teletherapy (IHT). The few studies that have been carried out so far have encountered a variety of logistical and technical problems, not least the difficulty of conducting properly controlled and blinded protocols that satisfy the requirements of high-level evidence-based research. In most cases, the equipment and communications technology were not designed for individuals with upper extremity disability. It is clear that exercise therapy combined with interventions such as FES, supervised over the Internet, will soon be adopted worldwide in one form or another. Therefore it is timely that researchers, clinicians, and healthcare planners interested in assessing IHT be aware of the pros and cons of the new technology and the factors involved in designing appropriate studies of it. It is crucial to understand the technical barriers, the role of telesupervisors, the motor improvements that participants can reasonably expect and the process of optimizing IHT-exercise therapy protocols to maximize the benefits of the emerging technology. Copyright © 2011 Elsevier B.V. All rights reserved.

  13. Improved Mars Upper Atmosphere Climatology

    Science.gov (United States)

    Bougher, S. W.

    2004-01-01

    The detailed characterization of the Mars upper atmosphere is important for future Mars aerobraking activities. Solar cycle, seasonal, and dust trends (climate) as well as planetary wave activity (weather) are crucial to quantify in order to improve our ability to reasonably depict the state of the Mars upper atmosphere over time. To date, our best information is found in the Mars Global Surveyor (MGS) Accelerometer (ACC) database collected during Phase 1 (Ls = 184 - 300; F10.7 = 70 - 90) and Phase 2 (Ls = 30 - 90; F10.7 = 90 - 150) of aerobraking. This database (100 - 170 km) consists of thermospheric densities, temperatures, and scale heights, providing our best constraints for exercising the coupled Mars General Circulation Model (MGCM) and the Mars Thermospheric General Circulation Model (MTGCM). The Planetary Data System (PDS) contains level 0 and 2 MGS Accelerometer data, corresponding to atmospheric densities along the orbit track. Level 3 products (densities, temperatures, and scale heights at constant altitudes) are also available in the PDS. These datasets provide the primary model constraints for the new MGCM-MTGCM simulations summarized in this report. Our strategy for improving the characterization of the Mars upper atmospheres using these models has been three-fold : (a) to conduct data-model comparisons using the latest MGS data covering limited climatic and weather conditions at Mars, (b) to upgrade the 15-micron cooling and near-IR heating rates in the MGCM and MTGCM codes for ad- dressing climatic variations (solar cycle and seasonal) important in linking the lower and upper atmospheres (including migrating tides), and (c) to exercise the detailed coupled MGCM and MTGCM codes to capture and diagnose the planetary wave (migrating plus non-migrating tidal) features throughout the Mars year. Products from this new suite of MGCM-MTGCM coupled simulations are being used to improve our predictions of the structure of the Mars upper atmosphere for the

  14. Virtual Reality Training for Upper Extremity in Subacute Stroke (VIRTUES)

    DEFF Research Database (Denmark)

    Brunner, Iris; Skouen, Jan Sture; Hofstad, Håkon

    2017-01-01

    Objective: To compare the effectiveness of upper extremity virtual reality rehabilitation training (VR) to time-matched conventional training (CT) in the subacute phase after stroke. Methods: In this randomized, controlled, single-blind phase III multicenter trial, 120 participants with upper...... extremity motor impairment within 12 weeks after stroke were consecutively included at 5 rehabilitation institutions. Participants were randomized to either VR or CT as an adjunct to standard rehabilitation and stratified according to mild to moderate or severe hand paresis, defined as $20 degrees wrist...... were assessed at baseline, after intervention, and at the 3-month follow-up. Results: Mean time from stroke onset for the VR group was 35 (SD 21) days and for the CT group was 34 (SD 19) days. There were no between-group differences for any of the outcome measures. Improvement of upper extremity motor...

  15. Dynamical Predictability of Monthly Means.

    Science.gov (United States)

    Shukla, J.

    1981-12-01

    We have attempted to determine the theoretical upper limit of dynamical predictability of monthly means for prescribed nonfluctuating external forcings. We have extended the concept of `classical' predictability, which primarily refers to the lack of predictability due mainly to the instabilities of synoptic-scale disturbances, to the predictability of time averages, which are determined by the predictability of low-frequency planetary waves. We have carded out 60-day integrations of a global general circulation model with nine different initial conditions but identical boundary conditions of sea surface temperature, snow, sea ice and soil moisture. Three of these initial conditions are the observed atmospheric conditions on 1 January of 1975, 1976 and 1977. The other six initial conditions are obtained by superimposing over the observed initial conditions a random perturbation comparable to the errors of observation. The root-mean-square (rms) error of random perturbations at all the grid points and all the model levels is 3 m s1 in u and v components of wind. The rms vector wind error between the observed initial conditions is >15 m s1.It is hypothesized that for a given averaging period, if the rms error among the time averages predicted from largely different initial conditions becomes comparable to the rms error among the time averages predicted from randomly perturbed initial conditions, the time averages are dynamically unpredictable. We have carried out the analysis of variance to compare the variability, among the three groups, due to largely different initial conditions, and within each group due to random perturbations.It is found that the variances among the first 30-day means, predicted from largely different initial conditions, are significantly different from the variances due to random perturbations in the initial conditions, whereas the variances among 30-day means for days 31-60 are not distinguishable from the variances due to random initial

  16. MASH test 3-11 of the TxDOT single slope bridge rail (type SSTR) on pan-formed bridge deck

    Science.gov (United States)

    2011-03-01

    The objective of this crash test was to determine whether the TxDOT Single Slope Traffic Rail (Type : SSTR) would perform acceptably on a pan-formed deck when tested according to the guidelines set forth in : Manual for Assessing Safety Hardware (MAS...

  17. Development of test method for assessing the bonding characteristics of membrane layers in wearing course laid on orthotropic steel bridge decks

    NARCIS (Netherlands)

    Liu, X.; Scarpas, A.; Li, J.; Tzimiris, G.; Hofman, R.; Voskuilen, J.

    2013-01-01

    In order to adequately characterize the adhesive bonding strength of the various membranes with surrounding materials on orthotropic steel decks and collect the necessary parameters for FE modeling, details of the Membrane Adhesion Test (MAT) are introduced. Analytical constitutive relations of the

  18. Development and use of 60 kV, and 150 kV floating deck modulators for high voltage protection of multi-megawatt ion beam accelerators

    International Nuclear Information System (INIS)

    Barber, G.C.; Ponte, N.S.; Schilling, G.

    1977-01-01

    Extraction currents of 60 A at 40 kV have been produced by utilizing a 60 kV floating deck modulator interfaced to a high voltage power supply. The modulator is operated in a series mode to repetitively pulse power to the ion beam accelerator. Current monitoring and other protective circuits provide interrupt commands to the series switch tube when faults occur. The constant current characteristics of the water cooled tetrode and the rapid response of the protective circuits effectively limit the fault energy to the ion source. Three of the 60 kV decks have been modified and stacked in a series configuration to supply 150 kV, 50 A pulses. This system supplies power for development of higher-energy multi-grid sources. In this system attention has been focused on forced voltage sharing of the three decks and on protective circuits for fault conditions. All control signal processing and conditioning is performed at ground level. Fiber optic links are used to interface with the high potential associated with the floating decks. A shunt modulator incorporated with this system provides regulation of the voltage to the ion source gradient grid. Future modulator development includes a system to deliver 100 A at 80 kV

  19. Upper Gastrointestinal Disorders in Children with End -Stage Renal Disease

    Directory of Open Access Journals (Sweden)

    Esfahani S.T

    2009-04-01

    Full Text Available This study was undertaken to define the prevalence of the upper Gastrointestinal (GI lesions, dyspeptic symptoms, H.pylori infection, and the impact of duration of dialysis on upper GI symptoms and lesions of children with End-stage renal disease. We studied 69 children with ESRD who were under regular hemodialysis therapy in our department. The age of the patients were between 4-18 years (mean: 11.3. 57(82.6% of 69 patients had GI symptoms and 12(17.4% were symptom free, the prevalence of each symptom in 57 symptomatic children was as follows: anorexia 48(84.2%, nausea/vomiting 39 (68.4%, belching/heartburn 20(35%, abdominal distention 15(26.3%, and epigastric pain 8(14%. 65(92.4% of 69 patients with ESRD had pathologic lesions and the most common lesion was gastritis .There was no case of gastric angiodysplasia in our patients. 15(21.7% of 69 patients had H. pylori infection. The prevalence of H.pylori infection in non-uremic children with upper GI symptoms is about 27% in our pediatric gastroenterology department, so there was no significant difference in prevalence of H.pylori infection between uremic and non-uremic children in our study (p value = 0.4735. There was no significant relationship between duration of dialysis and dyspeptic symptoms or upper GI lesions (p values were 0.8775 and 0.7435, respectively. Conclusions: Upper GI disorders are very common in children with ESRD, even when they have no upper GI symptoms, the most common lesion is gastritis. The prevalence of H.pylori infection is not different between children with ESRD and non-uremic children with upper GI symptoms, and duration of hemodialysis therapy has no significant effect on prevalence of GI symptoms and lesions.

  20. Biomechanics of fall arrest using the upper extremity: age differences.

    Science.gov (United States)

    Kim, Kyu-Jung; Ashton-Miller, James A

    2003-05-01

    This study tried to isolate critical biomechanical factors in fall arrests using the upper extremity during simulated forward falls. This study also attempted to find the differences in those factors between young and old age groups. The role of the upper extremity is not well defined despite its primary usage as a local shock absorber during fall impact. Comparative study in which two age groups underwent motion analysis.Methods. Ten healthy older males (mean age, 66.4 years) and 10 young males (mean age, 24.1 years) volunteered to perform self-initiated and cable-released falls at selected falling distances, while the joint motion and impact forces at the hand were recorded. Significant age differences were demonstrated in joint kinematics and impact force parameters at close distances. Excessive reflexive responses of the upper extremity in cable-released falls for the older adults resulted in 10-15 times higher peak impact forces and 2-3 times shorter body braking time than in self-initiated falls. Pre-impact activities of the upper extremity predispose the post-impact response during fall arrests. Suppressing excessive pre-impact reflexive activation of the arms could efficiently decrease the risk of fall-related injuries, which calls for securing sufficient arm movement time. Any fall prevention strategy that can increase arm movement time would be effective against injuries of the upper extremity during falling in the older adults. The findings will help to understand underlying mechanisms of fall arrest using the upper extremity for prevention of fall-related fractures.

  1. MEAN STACK WEB DEVELOPMENT

    OpenAIRE

    Le Thanh, Nghi

    2017-01-01

    The aim of the thesis is to provide a universal website using JavaScript as the main programming language. It also shows the basic parts anyone need to create a web application. The thesis creates a simple CMS using MEAN stack. MEAN is a collection of JavaScript based technologies used to develop web application. It is an acronym for MongoDB, Express, AngularJS and Node.js. It also allows non-technical users to easily update and manage a website’s content. But the application also lets o...

  2. Intersubjective meaning making

    DEFF Research Database (Denmark)

    Davidsen, Jacob

    of single-touch screen interaction among 8-9 year-old children presented here, shows that while the constraints of single-touch screens does not support equality of interaction at the verbal and the physical level, there seems to be an intersubjective learning outcome. More precisely, the constraints...... of single-touch screens offer support for intersubjective meaning making in its ability of constraining the interaction. By presenting a short embodied interaction analysis of 22 seconds of collaboration, I illustrate how an embodied interaction perspective on intersubjective meaning making can tell...... a different story about touch-screen supported collaborative learning....

  3. Computing meaning v.4

    CERN Document Server

    Bunt, Harry; Pulman, Stephen

    2013-01-01

    This book is a collection of papers by leading researchers in computational semantics. It presents a state-of-the-art overview of recent and current research in computational semantics, including descriptions of new methods for constructing and improving resources for semantic computation, such as WordNet, VerbNet, and semantically annotated corpora. It also presents new statistical methods in semantic computation, such as the application of distributional semantics in the compositional calculation of sentence meanings. Computing the meaning of sentences, texts, and spoken or texted dialogue i

  4. Assessment of undiscovered continuous gas resources in Upper Devonian Shales of the Appalachian Basin Province, 2017

    Science.gov (United States)

    Enomoto, Catherine B.; Trippi, Michael H.; Higley, Debra K.; Rouse, William A.; Dulong, Frank T.; Klett, Timothy R.; Mercier, Tracey J.; Brownfield, Michael E.; Leathers-Miller, Heidi M.; Finn, Thomas M.; Marra, Kristen R.; Le, Phuong A.; Woodall, Cheryl A.; Schenk, Christopher J.

    2018-04-19

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable continuous resources of 10.7 trillion cubic feet of natural gas in Upper Devonian shales of the Appalachian Basin Province.

  5. Prevalence of upper limb disorders among female librarians.

    Science.gov (United States)

    Pandy, R

    2013-09-01

    Work as a librarian involves exposure to potential risk factors for developing upper limb disorders. The prevalence of upper limb symptoms has, however, not previously been assessed in this occupational group. To estimate the 7-day and annual prevalence of self-reported neck and upper limb symptoms in librarians and to examine associations with specific tasks and ergonomic risk factors. A cross-sectional study using components of the standardized Nordic questionnaire. The study population consisted of librarians employed by a large local authority, and data collection was by means of a self-administered questionnaire. from studies on keyboard workers and on the general population were used as comparators. The 7-day prevalence of self-reported neck and upper limb pain in female librarians was 42% (95% confidence interval (CI) 33.7-50.5) and the annual prevalence was 65% (95% CI 56.6-72.8). The prevalence of reported wrist and hand pain increased with increased working involving a wide thumb-index span (P librarians was high, but there was insufficient evidence to confirm whether the prevalence was higher than in the general population or among keyboard workers. Working with a wide thumb-index span was associated with reporting upper limb symptoms.

  6. Upper lip changes and gingival exposure on smiling: vertical dimension analysis.

    Science.gov (United States)

    Miron, Hagai; Calderon, Shlomo; Allon, Dror

    2012-01-01

    Our objectives were to evaluate and quantify upper lip soft-tissue changes in the vertical dimensions both at rest and at maximum smile, and to examine the correlation between upper labial vestibular attachment height and maxillary gingival exposure on smiling. Seventy-two volunteers (36 men, 36 women) aged 20 to 40 (mean, 30.49 years) were recruited for this study. For each subject, 9 measurements of upper lip position and maxillary incisor crown height at rest and in maximum smile were recorded. A statistically significant sexual dimorphism was apparent in most of the measured variables. Relaxed external upper lip length was 3.1 mm shorter in the women than in the men. The mean maxillary central incisor display at rest was 1.78 mm greater in the women than in the men. A high smile line was 2.5 times more prevalent in the women. The upper lip was shortened by 30% in subjects with a high smile line compared with 23% in subjects with a low smile line. The following findings were observed in subjects with a high smile pattern: (1) short upper lip length, (2) low smiling/resting upper lip length ratio, (3) inferior attachment of the upper labial vestibule, and (4) prominent upper lip vermilion. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

  7. Mean intraocular pressure in hypertensive adults

    International Nuclear Information System (INIS)

    Irum, S.; Malik, A.M.; Saeed, M.

    2015-01-01

    To determine the mean Intraocular Pressure (IOP) in already diagnosed adult hypertensive patients with different grades of hypertension. Study Design: Cross-sectional descriptive study. Place and Duration of Study: Combined Military Hospital, Lahore, from March 2012 to Aug 2012. Patients and Methods: A total of 178 already diagnosed hypertensive patients were selected. A detailed history of ocular or systemic diseases was taken. Intraocular pressure was measured with help of Goldmann applanation tonometer. Three consecutive readings of IOP of each eye were taken at 30 minutes interval and mean calculated. Blood pressure was recorded in seated position from right upper arm, by mercury sphygmomanometer. Blood pressure measurements were determined by taking the mean value of three systolic and diastolic readings. Results: The results of intraocular pressure (IOP) between various grades of hypertension were determined. There was an increase in mean IOP with rise in blood pressure. The subjects with grade I hypertension showed a mean IOP of 13.95 ± 3.74 mmHg, while grade II and grade III hypertensive subjects had mean IOPs as 18.10 ± 3.32 and 20.21 ± 2.52 mmHg respectively. Conclusion: A higher value of mean IOP was found with increase in systolic and diastolic blood pressures. (author)

  8. Engagement Means Everyone

    Science.gov (United States)

    Patton, Carol

    2012-01-01

    Employee engagement is not just HR's responsibility. While HR is responsible for the process of measuring and driving engagement, improving it is actually everyone's responsibility. And that means reducing the barriers to productivity to drive business performance. Training departments can play a pivotal role. Their job is to enhance curriculum or…

  9. Monstrosity by Monstrous Means

    DEFF Research Database (Denmark)

    Post, Hans Christian

    2016-01-01

    The Cambodian memorials to the Cambodian genocide between 1975 and 1979 can in numerous ways be termed monstrous. Not so much in that they deal with atrocities monstrous in scale and character, as in the monstrous visual means they employ and the imprecise, monster-ridden explanations they delive...

  10. The meaning of talent

    Directory of Open Access Journals (Sweden)

    Raquel Lorenzo

    2006-01-01

    Full Text Available The knowledge society gives a remarkable role to human potentialities into organizations. For this reason has emerged talent management. But it is necessary to know its meaning to put on practice programs. In this paper, the author analyzes different points of views about this topic.

  11. Meaning construction in remembering

    DEFF Research Database (Denmark)

    Wagoner, Brady

    2011-01-01

    F.C. Bartlett and L.S.Vygotsky were two seminal figures in the psychological study of remembering. Both emphasized the role of meaning and imagination in this process. Bartlett did this by showing the systematic and holistic changes that ensue when cultural material is repeatedly reproduced outsi...

  12. PR Means Positive Results.

    Science.gov (United States)

    Foree, Marilyn

    1992-01-01

    Describes the advantages of public relations to a school music program. Suggests that, to succeed, a music program must have the support of school administrators, teachers, parents, and students alike. Recommends means of attracting support from the four groups. Stresses the importance of effective local publicity. (SG)

  13. Jeans and Means

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 1; Issue 8. Jeans and Means - The Story of Indigo. Subramania Ranganathan. Series Article Volume 1 Issue 8 August 1996 pp 22-27. Fulltext. Click here to view fulltext PDF. Permanent link: https://www.ias.ac.in/article/fulltext/reso/001/08/0022-0027 ...

  14. Levels of Literary Meaning

    DEFF Research Database (Denmark)

    Klausen, Søren Harnow

    2017-01-01

    I argue that intentionalist theories of meaning and interpretation, like those of Hirsch and Juhl, have been insufficiently attentive to the different levels of authorial intention that are operative in literary works. By countenancing intentions on different levels – ranging from simple semantic...

  15. Numerical Simulation of Early Age Cracking of Reinforced Concrete Bridge Decks with a Full-3D Multiscale and Multi-Chemo-Physical Integrated Analysis

    Directory of Open Access Journals (Sweden)

    Tetsuya Ishida

    2018-03-01

    Full Text Available In November 2011, the Japanese government resolved to build “Revival Roads” in the Tohoku region to accelerate the recovery from the Great East Japan Earthquake of March 2011. Because the Tohoku region experiences such cold and snowy weather in winter, complex degradation from a combination of frost damage, chloride attack from de-icing agents, alkali–silica reaction, cracking and fatigue is anticipated. Thus, to enhance the durability performance of road structures, particularly reinforced concrete (RC bridge decks, multiple countermeasures are proposed: a low water-to-cement ratio in the mix, mineral admixtures such as ground granulated blast furnace slag and/or fly ash to mitigate the risks of chloride attack and alkali–silica reaction, anticorrosion rebar and 6% entrained air for frost damage. It should be noted here that such high durability specifications may conversely increase the risk of early age cracking caused by temperature and shrinkage due to the large amounts of cement and the use of mineral admixtures. Against this background, this paper presents a numerical simulation of early age deformation and cracking of RC bridge decks with full 3D multiscale and multi-chemo-physical integrated analysis. First, a multiscale constitutive model of solidifying cementitious materials is briefly introduced based on systematic knowledge coupling microscopic thermodynamic phenomena and microscopic structural mechanics. With the aim to assess the early age thermal and shrinkage-induced cracks on real bridge deck, the study began with extensive model validations by applying the multiscale and multi-physical integrated analysis system to small specimens and mock-up RC bridge deck specimens. Then, through the application of the current computational system, factors that affect the generation and propagation of early age thermal and shrinkage-induced cracks are identified via experimental validation and full-scale numerical simulation on real

  16. Large Abundances of Polycyclic Aromatic Hydrocarbons in Titan's Upper Atmosphere

    Science.gov (United States)

    Lopez-Puertas, M.; Dinelli, B. M.; Adriani, A.; Funke, B.; Garcia-Comas, M.; Moriconi, M. L.; D'Aversa, E.; Boersma, C.; Allamandola, L. J.

    2013-01-01

    In this paper, we analyze the strong unidentified emission near 3.28 micron in Titan's upper daytime atmosphere recently discovered by Dinelli et al.We have studied it by using the NASA Ames PAH IR Spectroscopic Database. The polycyclic aromatic hydrocarbons (PAHs), after absorbing UV solar radiation, are able to emit strongly near 3.3 micron. By using current models for the redistribution of the absorbed UV energy, we have explained the observed spectral feature and have derived the vertical distribution of PAH abundances in Titan's upper atmosphere. PAHs have been found to be present in large concentrations, about (2-3) × 10(exp 4) particles / cubic cm. The identified PAHs have 9-96 carbons, with a concentration-weighted average of 34 carbons. The mean mass is approx 430 u; the mean area is about 0.53 sq. nm; they are formed by 10-11 rings on average, and about one-third of them contain nitrogen atoms. Recently, benzene together with light aromatic species as well as small concentrations of heavy positive and negative ions have been detected in Titan's upper atmosphere. We suggest that the large concentrations of PAHs found here are the neutral counterpart of those positive and negative ions, which hence supports the theory that the origin of Titan main haze layer is located in the upper atmosphere.

  17. Vision-Based Autonomous Landing of a Quadrotor on the Perturbed Deck of an Unmanned Surface Vehicle

    Directory of Open Access Journals (Sweden)

    Riccardo Polvara

    2018-04-01

    Full Text Available Autonomous landing on the deck of an unmanned surface vehicle (USV is still a major challenge for unmanned aerial vehicles (UAVs. In this paper, a fiducial marker is located on the platform so as to facilitate the task since it is possible to retrieve its six-degrees of freedom relative-pose in an easy way. To compensate interruption in the marker’s observations, an extended Kalman filter (EKF estimates the current USV’s position with reference to the last known position. Validation experiments have been performed in a simulated environment under various marine conditions. The results confirmed that the EKF provides estimates accurate enough to direct the UAV in proximity of the autonomous vessel such that the marker becomes visible again. Using only the odometry and the inertial measurements for the estimation, this method is found to be applicable even under adverse weather conditions in the absence of the global positioning system.

  18. DECK: Distance and environment-dependent, coarse-grained, knowledge-based potentials for protein-protein docking

    Directory of Open Access Journals (Sweden)

    Vakser Ilya A

    2011-07-01

    Full Text Available Abstract Background Computational approaches to protein-protein docking typically include scoring aimed at improving the rank of the near-native structure relative to the false-positive matches. Knowledge-based potentials improve modeling of protein complexes by taking advantage of the rapidly increasing amount of experimentally derived information on protein-protein association. An essential element of knowledge-based potentials is defining the reference state for an optimal description of the residue-residue (or atom-atom pairs in the non-interaction state. Results The study presents a new Distance- and Environment-dependent, Coarse-grained, Knowledge-based (DECK potential for scoring of protein-protein docking predictions. Training sets of protein-protein matches were generated based on bound and unbound forms of proteins taken from the DOCKGROUND resource. Each residue was represented by a pseudo-atom in the geometric center of the side chain. To capture the long-range and the multi-body interactions, residues in different secondary structure elements at protein-protein interfaces were considered as different residue types. Five reference states for the potentials were defined and tested. The optimal reference state was selected and the cutoff effect on the distance-dependent potentials investigated. The potentials were validated on the docking decoys sets, showing better performance than the existing potentials used in scoring of protein-protein docking results. Conclusions A novel residue-based statistical potential for protein-protein docking was developed and validated on docking decoy sets. The results show that the scoring function DECK can successfully identify near-native protein-protein matches and thus is useful in protein docking. In addition to the practical application of the potentials, the study provides insights into the relative utility of the reference states, the scope of the distance dependence, and the coarse-graining of

  19. Ground penetrating radar and microwave tomography 3D applications for the deck evaluation of the Musmeci bridge in Potenza, Italy

    International Nuclear Information System (INIS)

    Bavusi, Massimo; Loperte, Antonio; Lapenna, Vincenzo; Soldovieri, Francesco; Di Napoli, Rosario; Di Cesare, Antonio; Carlo Ponzo, Felice

    2011-01-01

    An extensive experimental and numerical investigation has been carried out to assess the status of the 'Ponte sul Basento' (1967–1976), in the town of Potenza (Basilicata region, southern Italy), better known as the Musmeci bridge. Architecturally, the bridge is a considerable reinforced 20th century concrete structure that was designed and built by the Italian architect Sergio Musmeci (1926–1981). Moreover, the bridge represents an important element of the infrastructural network, linking the city centre to the Potenza-Sicignano highway, crossing the Basento river and the railway close to the main train station of the city. Recently, due to ageing and continuous and significant traffic, the bridge started to be affected by several problems such as water infiltration. Within the presented study, a widespread ground penetrating radar (GPR) survey has been designed to investigate the geometrical characteristics of the bridge deck (Gerber saddles, internal stiffening walls, pillar supports) and detect the presence of defects or damage due to water infiltration and traffic fatigue. Concerning this, a 900 MHz 3D GPR survey has been performed along a zone of one of the lanes on the road surface. Moreover, a second 1500 MHz 3D survey has been carried out at the bottom of the bridge deck in order to gain detailed information about an important structural element of the bridge, the Gerber saddle. Both results have been processed following two approaches: the first a classical time-domain processing session based on commercial software and the use of migration; the second in microwave tomography, an advanced frequency domain automatic PC-based inversion algorithm. In this paper, we present a comparative interpretation of both kinds of processed results, and provide considerations about the investigated structures

  20. Negotiating meaning through artefacts

    DEFF Research Database (Denmark)

    Tavella, Elena

    2015-01-01

    This research contributes to the domain of strategy making, specifically to unpacking the complexity of sociomateriality in strategy discourse. Scholars have emphasized the potential of artefacts to enhance sensemaking during strategizing. However there is a lack of insight into how artefacts...... and conversational aspects are linked at the micro‑level of discourse, also how artefacts and sensemaking shape one another. This research addresses this gap by empirically analyzing strategy discourse within a facilitated modelling workshop. Considering strategizing as a socially constructed activity, the author...... analyzes a workshop transcript to assess the extent to which stakeholders’ appropriation of artefacts supports them in engaging in negotiation of meaning with action implications. Moreover, how artefacts and negotiation of meaning shape one another is identified. The data suggest that appropriating...

  1. Composites for Exploration Upper Stage

    Science.gov (United States)

    Fikes, J. C.; Jackson, J. R.; Richardson, S. W.; Thomas, A. D.; Mann, T. O.; Miller, S. G.

    2016-01-01

    The Composites for Exploration Upper Stage (CEUS) was a 3-year, level III project within the Technology Demonstration Missions program of the NASA Space Technology Mission Directorate. Studies have shown that composites provide important programmatic enhancements, including reduced weight to increase capability and accelerated expansion of exploration and science mission objectives. The CEUS project was focused on technologies that best advanced innovation, infusion, and broad applications for the inclusion of composites on future large human-rated launch vehicles and spacecraft. The benefits included near- and far-term opportunities for infusion (NASA, industry/commercial, Department of Defense), demonstrated critical technologies and technically implementable evolvable innovations, and sustained Agency experience. The initial scope of the project was to advance technologies for large composite structures applicable to the Space Launch System (SLS) Exploration Upper Stage (EUS) by focusing on the affordability and technical performance of the EUS forward and aft skirts. The project was tasked to develop and demonstrate critical composite technologies with a focus on full-scale materials, design, manufacturing, and test using NASA in-house capabilities. This would have demonstrated a major advancement in confidence and matured the large-scale composite technology to a Technology Readiness Level 6. This project would, therefore, have bridged the gap for providing composite application to SLS upgrades, enabling future exploration missions.

  2. Six upper incisors: what's next?

    Science.gov (United States)

    Berneburg, Mirjam; Meller, Christian

    2016-01-01

    This case report describes our therapeutic approach taken in a girl with eruption disturbance of the upper anterior teeth. Two supernumerary teeth were involved, which required a combination of orthodontic and surgical treatment. The initial situation in the upper anterior segment was characterized by two supernumerary mesial incisors, ectopic eruption of the distally located lateral incisors, and crowded tooth buds in the canine areas. Key decisions had to be made as to whether any teeth needed to be extracted and, if so, regarding the timing and sites of extraction. Removing teeth too early would have preempted a complete assessment of tooth quality, whereas late extraction would have carried a risk of eruption disturbance. Once the distal lateral incisors had erupted, the supernumerary mesial incisors were extracted and the central incisors (initially located in between) mesialized with a bracket appliance. Following space closure and mesialization of the lateral incisors, a functional appliance was used. Tooth 13 was erupting, while tooth 23 was displaced and subsequently aligned as part of the final bracket treatment. To successfully treat eruption disturbances, a careful diagnostic workup is essential, including informative radiographs, personalized treatment planning, and correct decision-making as to whether teeth need to be extracted and regarding the timing and sites of extraction. Finally, the eruption of the canines should be monitored.

  3. Means on scattered compacta

    Czech Academy of Sciences Publication Activity Database

    Banakh, T.; Bonnet, R.; Kubiś, Wieslaw

    2014-01-01

    Roč. 2, č. 1 (2014), s. 5-10 ISSN 2299-3231 R&D Projects: GA ČR(CZ) GAP201/12/0290 Institutional support: RVO:67985840 Keywords : scattered compact space * mean operation Subject RIV: BA - General Mathematics http://www.degruyter.com/view/j/taa.2014.2.issue-1/taa-2014-0002/taa-2014-0002.xml

  4. The Meaning of Mandela

    DEFF Research Database (Denmark)

    Krabbe, Julia Suárez

    2017-01-01

    Book Reviews The Meaning of Mandela: A Broader Canvas. Sabelo J. Ndlovu-Gatsheni, The Decolonial Mandela: Peace, Justice and the Politics of Life (Oxford and New York, Berghahn Books, 2016), 186 pp., hardback, £64.00, US$90.00, ISBN 978-1-78533-118-3; paperback, £19.00, US$27.95, ISBN 978......-1-78533-296-8; e-book, ISBN 978-1-79533-119-0...

  5. Meaning and significance of

    Directory of Open Access Journals (Sweden)

    Ph D Student Roman Mihaela

    2011-05-01

    Full Text Available The concept of "public accountability" is a challenge for political science as a new concept in this area in full debate and developement ,both in theory and practice. This paper is a theoretical approach of displaying some definitions, relevant meanings and significance odf the concept in political science. The importance of this concept is that although originally it was used as a tool to improve effectiveness and eficiency of public governance, it has gradually become a purpose it itself. "Accountability" has become an image of good governance first in the United States of America then in the European Union.Nevertheless,the concept is vaguely defined and provides ambiguous images of good governance.This paper begins with the presentation of some general meanings of the concept as they emerge from specialized dictionaries and ancyclopaedies and continues with the meanings developed in political science. The concept of "public accontability" is rooted in economics and management literature,becoming increasingly relevant in today's political science both in theory and discourse as well as in practice in formulating and evaluating public policies. A first conclusin that emerges from, the analysis of the evolution of this term is that it requires a conceptual clarification in political science. A clear definition will then enable an appropriate model of proving the system of public accountability in formulating and assessing public policies, in order to implement a system of assessment and monitoring thereof.

  6. Upper Blepharoplasty and Lateral Wound Dehiscence.

    Science.gov (United States)

    Kashkouli, Mohsen Bahmani; Jamshidian-Tehrani, Mansooreh; Sharzad, Sahab; Sanjari, Mostafa Soltan

    2015-01-01

    To report the frequency of lateral wound dehiscence (LWD) after upper blepharoplasty (UB), a technique and its outcome to prevent LWD. A retrospective review was performed for cases of LWD after UB presenting between 2003 and 2009, and then a prospective comparative study was performed between February 2009 and March 2013. For the comparison, subjects were divided into two groups based on intraoperative assessment of lateral wound tension (same technique and surgeon). Group 1 received 1-3 orbicularis/subcutaneous buried sutures (6-0 polyglactin) before interrupted 6-0 nylon skin closure. Group 2 underwent skin closure only. Subjects, who had re-operation, skin healing disorders, and incomplete follow-up (LWD with a mean age of 36.2 years in the audit (2003-2009). The prospective study included 68 subjects (68/293, 23.2%) in Group 1 and 225 in Group 2. Gender and simultaneous forehead and eyebrow procedures were similar between groups (P = 0.3 and P = 0.4 respectively). Group 1 was statistically significantly younger at mean age of 41.4 years, compared to Group 2 at 56.1 years (P = 0.000). The frequency of LWD significantly (P = 0.04) decreased to 0.3% (1/293). In the presence of wound tension on skin closure (intraoperative assessment), tension relieving buried orbicularis/subcutaneous 6-0 polyglactin suturing of the lateral UB incision could prevent LWD.

  7. Late renal function after upper abdominal irradiation

    International Nuclear Information System (INIS)

    Morris, Monica M.; Willett, Christopher G.

    1997-01-01

    Purpose: This study assesses the late renal function and complications following upper abdominal irradiation. Methods and Materials: Eighty-six adult patients were identified who were treated with curative intent to the upper abdomen, received greater than 50% unilateral kidney irradiation to doses of at least 26 Gy, and survived for 1 year or more. Following treatment, the clinical course, blood pressure, addition of anti-hypertensive medications, serum creatinine and creatinine clearance were determined. Creatinine clearance was calculated by the formula: creatinine clearance equals [(140 - age) x (weight in kilograms)] / (72 x serum creatinine), which has a close correlation to creatinine clearances measured by 24 hour urine measurement. The percent change in creatinine clearance from pre-treatment values was analyzed. Mean follow-up was 6.7 years. Seventeen patients were followed for 11 or more years. Results: Of the 16 patients with pre-radiotherapy hypertension, eight required an increase in the number of medications for control and eight required no change in medication. Twenty-one patients developed hypertension in follow-up, 15 of whom required no medication. One patient developed malignant hypertension on the basis of renal artery stenosis. Acute or chronic renal failure was not observed in any patient. The serum creatinine for all 86 patients prior to irradiation was below 2 mg/100 ml; in follow-up it rose to between 2-3 mg/100 ml in five patients. On univariate analysis, older patient age, female sex, pre-existing hypertension and initially abnormal renal function (creatinine clearance <90mg/ml) were significantly correlated with later poor creatinine clearance (<50 mg/ml). Conclusions: After significant unilateral kidney irradiation, patients demonstrated a laboratory trend to increased creatinine and decreased creatinine clearance. With long-term follow-up, these physiologic changes did not appear to translate into a clinically relevant alteration in

  8. The Meaning of Freedom

    Directory of Open Access Journals (Sweden)

    Luis Eduardo Hoyos

    2009-12-01

    Full Text Available In the article it is pretended to prepare the conceptual field for the correct use of the attribution of freedom. It is defended the importance to consider the complementarity of freedom of action and freedom of the will and it is argued for a non-metaphysical conception of adscription of freedom. The adequate use of the attribution of freedom is social and normative. This means additionally that the freedom is not a presupposition of the moral responsibility and the authorship, but on the contrary the moral responsibility and the authorship are presuppositions of the attribution of freedom.

  9. Music, memory and meaning

    OpenAIRE

    Fair, Laura

    2012-01-01

    I his paper examines the music and career of Siti binti Saadi, a famous taarab musician who performed in Zanzibar during the 1920s and 1930s. Relying on four distinctive types of evidence: her recorded music, written documentation produced in East Africa, interviews with men and women who heard her perform and records of company executives I compare perspectives regarding the source of power and authority attributed to her voice as well as the meaning of her music. Siti binti Saadi was the fi...

  10. NOAA Climate Data Record for Mean Layer Temperature (Upper Troposphere & Lower Stratosphere) from UCAR, Version 2

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Temperatures of Troposphere / Stratosphere (TTS) (AMSU channel 7 and MSU channel 3) CDR is generated by using National Oceanic and Atmospheric Administration...

  11. Iodine removing means

    International Nuclear Information System (INIS)

    Takeshima, Masaki.

    1975-01-01

    Object: To employ exhaust gas from an incinerator to effect regeneration of an adsorbent such as active carbon which has adsorbed a radioactive gas such as iodine contained in the ventilating system exhaust gas of a boiling water reactor power plant. Structure: Radioactive exhaust gas such as iodine, xenon and krypton is led to an active carbon adsorbing means for removal through adsorption. When the adsorbing function of the active carbon adsorption means is reduced, the exhaust gas discharged from the incinerator is cooled down to 300 0 C and then caused to flow into the active carbon layer, and after depriving it of sulfur dioxide gas, oxides of nitrogen, daughter nuclides resulting from attenuation of radioactive gas and so forth, these being adsorbed by the carbon active layer, it is led again to the incinerator, whereby the radioactivity accompanying the regenerated gas is sealed as ash within the incinerator. Further, similarly accompanying fine active carbon particles and the like are utilized as a heat source for the incinerator. (Kamimura, M.)

  12. Updates on upper eyelid blepharoplasty

    Directory of Open Access Journals (Sweden)

    Kasturi Bhattacharjee

    2017-01-01

    Full Text Available The human face is composed of small functional and cosmetic units, of which the eyes and periocular region constitute the main point of focus in routine face-to-face interactions. This dynamic region plays a pivotal role in the expression of mood, emotion, and character, thus making it the most relevant component of the facial esthetic and functional unit. Any change in the periocular unit leads to facial imbalance and functional disharmony, leading both the young and the elderly to seek consultation, thus making blepharoplasty the surgical procedure of choice for both cosmetic and functional amelioration. The applied anatomy, indications of upper eyelid blepharoplasty, preoperative workup, surgical procedure, postoperative care, and complications would be discussed in detail in this review article.

  13. Climate of the upper atmosphere

    Directory of Open Access Journals (Sweden)

    Christoph Jacobi

    2009-06-01

    Full Text Available

    In the frame of the European COST 296 project (Mitigation of Ionospheric Effects on Radio Systems, MIERS

    investigations of the climate of the upper atmosphere have been carried out during the last four years to obtain

    new information on the upper atmosphere. Mainly its ionospheric part has been analysed as the ionosphere

    most essential for the propagation of radio waves. Due to collaboration between different European partners

    many new results have been derived in the fields of long-term trends of different ionospheric and related atmospheric

    parameters, the investigations of different types of atmospheric waves and their impact on the ionosphere,

    the variability of the ionosphere, and the investigation of some space weather effects on the ionosphere.


  14. Clinical comparison of automatic, noninvasive measurements of blood pressure in the forearm and upper arm.

    Science.gov (United States)

    Schell, Kathleen; Bradley, Elisabeth; Bucher, Linda; Seckel, Maureen; Lyons, Denise; Wakai, Sandra; Bartell, Deborah; Carson, Elizabeth; Chichester, Melanie; Foraker, Teresa; Simpson, Kathleen

    2005-05-01

    When the upper arm (area from shoulder to elbow) is inaccessible and/or a standard-sized blood pressure cuff does not fit, some healthcare workers use the forearm to measure blood pressure. To compare automatic noninvasive measurements of blood pressure in the upper arm and forearm. A descriptive, correlational comparison study was conducted in the emergency department of a 1071-bed teaching hospital. Subjects were 204 English-speaking patients 6 to 91 years old in medically stable condition who had entered the department on foot or by wheelchair and who had no exclusions to using their left upper extremity. A Welch Allyn Vital Signs 420 series monitor was used to measure blood pressure in the left upper arm and forearm with the subject seated and the upper arm or forearm at heart level. Pearson r correlation coefficients between measurements in the upper arm and forearm were 0.88 for systolic blood pressure and 0.76 for diastolic blood pressure (P upper arm and forearm differed significantly (t = 2.07, P = .04). A Bland-Altman analysis indicated that the distances between the mean values and the limits of agreement for the 2 sites ranged from 15 mm Hg (mean arterial pressure) to 18.4 mm Hg (systolic pressure). Despite strict attention to correct cuff size and placement of the upper arm or forearm at heart level, measurements of blood pressure obtained noninvasively in the arm and forearm of seated patients in stable condition are not interchangeable.

  15. Rapid replacement of bridge deck expansion joints study - phase I : [tech transfer summary].

    Science.gov (United States)

    2014-12-01

    This initial research phase focused on documenting the current : means and methods of bridge expansion joint deterioration, : maintenance, and replacement and on identifying improvements : through all of the input gathered.

  16. Ordinary and extraordinary means.

    Science.gov (United States)

    Gillon, R

    1986-01-25

    The Roman Catholic doctrine of ordinary and extraordinary means in patient care decisions is the subject of this essay in Gillon's series on medical ethics. He briefly traces the Church history of this doctrine, which holds that saving life is not obligatory if doing so would be excessively burdensome or disproportionate in relation to the expected benefits. The burdens and benefits are to be weighed in the context of "circumstances of persons, places, times, and cultures," and factors such as the costs and risks of undergoing a proposed treatment may be considered. Gillon also notes the disagreement among Roman Catholic commentators over whether it is ever permissible to discontinue feeding as a burdensome, extraordinary treatment. He concludes that, despite different weightings of harms and benefits, Roman Catholic and non-Catholic thinkers are in accord over the appropriate moral approach to deciding when treatment is not obligatory.

  17. Focus on Meaning

    DEFF Research Database (Denmark)

    Zhang, Chun; Wang Jingjing, Jenny

    recognizing new vocabulary (two-, three and four-character words) in a series of simple meaning recognition tests administered by the authors over three weeks. The test sets consist of vocabulary with target words that were given semantic and conceptual explanation by the authors in the previous week......Abstract This study examines the effect of mapping between the semantic and conceptual representation of target words 房,堂,屋, and 厅on Chinese (L2) vocabulary learning at a university class. Students (N=25) were the 2nd-year Chinese –major students at one university in Denmark. They were given tests...... of Chinese (L2) words can have a measurable effect on students’ efficacy of (Nation 2011) vocabulary learning in the classroom. The findings also reveal that conceptual representation of Chinese (L2) words reinforce the students’ reliance on L 1 by building a link between L 1semantic representations and L 2...

  18. Mean inactivation dose (D)

    International Nuclear Information System (INIS)

    Vijayakumar, S.; Ng, T.C.; Raudkivi, U.; Meaney, T.J.

    1990-01-01

    By predicting treatment outcome to radiotherapy from in vitro radiobiological parameters, not only individual patient treatments can be tailored, but also new promising treatment protocols can be tried in patients in whom unfavorable outcome is predicted. In this respect, choosing the right parameter can be very important. Unlike D 0 and N which provide information of the distal part of the survival curve, mean inactivation dose (D) estimates overall radiosensitivity. However, the parameters reflecting the response at the clinically relevant low-dose region are neglected in the literature. In a literature survey of 98 papers in which survival curves or D 0 /N were used, only in 2 D was used. In 21 papers the D 0 /n values were important in drawing conclusions. By calculating D in 3 of these 21 papers, we show that the conclusion drawn may be altered with the use of D. The importance of ''low-dose-region-parameters'' is reviewed. (orig.)

  19. The mean Evershed flow

    Science.gov (United States)

    Hu, W.-R.

    1984-09-01

    The paper gives a theoretical analysis of the overall characteristics of the Evershed flow (one of the main features of sunspots), with particular attention given to its outward flow from the umbra in the photosphere, reaching a maximum somewhere in the penumbra, and decreasing rapidly further out, and its inward flow of a comparable magnitude in chromosphere. Because the inertial force of the flow is small, the relevant dynamic process can be divided into a base state and a perturbation. The base-state solution yields the equilibrium relations between the pressure gradient, the Lorentz force, and gravity, and the flow law. The perturbation describes the force driving the Evershed flow. Since the pressure gradient in the base state is already in equilibrium with the Lorentz force and the gravity, the driving force of the mean Evershed flow is small.

  20. Improvisation and meaning.

    Science.gov (United States)

    Gilbertson, Simon

    2013-08-07

    This article presents and discusses a long-term repeated-immersion research process that explores meaning allocated to an episode of 50 seconds of music improvisation in early neurosurgical rehabilitation by a teenage boy with severe traumatic brain injury and his music therapist. The process began with the original therapy session in August 1994 and extends to the current time of writing in 2013. A diverse selection of qualitative research methods were used during a repeated immersion and engagement with the selected episodes. The multiple methods used in this enquiry include therapeutic narrative analysis and musicological and video analysis during my doctoral research between 2002 and 2004, arts-based research in 2008 using expressive writing, and arts-based research in 2012 based on the creation of a body cast of my right hand as I used it to play the first note of my music improvising in the original therapy episode, which is accompanied by reflective journaling. The casting of my hand was done to explore and reconsider the role of my own body as an embodied and integral, but originally hidden, part of the therapy process. Put together, these investigations explore the potential meanings of the episode of music improvisation in therapy in an innovative and imaginative way. However, this article does not aim at this stage to present a model or theory for neurorehabilitation but offers an example of how a combination of diverse qualitative methods over an extended period of time can be instrumental in gaining innovative and rich insights into initially hidden perspectives on health, well-being, and human relating.

  1. Improvisation and meaning

    Directory of Open Access Journals (Sweden)

    Simon Gilbertson

    2013-08-01

    Full Text Available This article presents and discusses a long-term repeated-immersion research process that explores meaning allocated to an episode of 50 seconds of music improvisation in early neurosurgical rehabilitation by a teenage boy with severe traumatic brain injury and his music therapist. The process began with the original therapy session in August 1994 and extends to the current time of writing in 2013. A diverse selection of qualitative research methods were used during a repeated immersion and engagement with the selected episodes. The multiple methods used in this enquiry include therapeutic narrative analysis and musicological and video analysis during my doctoral research between 2002 and 2004, arts-based research in 2008 using expressive writing, and arts-based research in 2012 based on the creation of a body cast of my right hand as I used it to play the first note of my music improvising in the original therapy episode, which is accompanied by reflective journaling. The casting of my hand was done to explore and reconsider the role of my own body as an embodied and integral, but originally hidden, part of the therapy process. Put together, these investigations explore the potential meanings of the episode of music improvisation in therapy in an innovative and imaginative way. However, this article does not aim at this stage to present a model or theory for neurorehabilitation but offers an example of how a combination of diverse qualitative methods over an extended period of time can be instrumental in gaining innovative and rich insights into initially hidden perspectives on health, well-being, and human relating.

  2. Improvisation and meaning

    Science.gov (United States)

    2013-01-01

    This article presents and discusses a long-term repeated-immersion research process that explores meaning allocated to an episode of 50 seconds of music improvisation in early neurosurgical rehabilitation by a teenage boy with severe traumatic brain injury and his music therapist. The process began with the original therapy session in August 1994 and extends to the current time of writing in 2013. A diverse selection of qualitative research methods were used during a repeated immersion and engagement with the selected episodes. The multiple methods used in this enquiry include therapeutic narrative analysis and musicological and video analysis during my doctoral research between 2002 and 2004, arts-based research in 2008 using expressive writing, and arts-based research in 2012 based on the creation of a body cast of my right hand as I used it to play the first note of my music improvising in the original therapy episode, which is accompanied by reflective journaling. The casting of my hand was done to explore and reconsider the role of my own body as an embodied and integral, but originally hidden, part of the therapy process. Put together, these investigations explore the potential meanings of the episode of music improvisation in therapy in an innovative and imaginative way. However, this article does not aim at this stage to present a model or theory for neurorehabilitation but offers an example of how a combination of diverse qualitative methods over an extended period of time can be instrumental in gaining innovative and rich insights into initially hidden perspectives on health, well-being, and human relating. PMID:23930989

  3. Diagnosis and treatment of upper limb apraxia

    OpenAIRE

    Dovern, A.; Fink, G. R.; Weiss, P. H.

    2012-01-01

    Upper limb apraxia, a disorder of higher motor cognition, is a common consequence of left-hemispheric stroke. Contrary to common assumption, apraxic deficits not only manifest themselves during clinical testing but also have delirious effects on the patients’ everyday life and rehabilitation. Thus, a reliable diagnosis and efficient treatment of upper limb apraxia is important to improve the patients’ prognosis after stroke. Nevertheless, to date, upper limb apraxia is still an underdiagnosed...

  4. Fuzzy upper bounds and their applications

    Energy Technology Data Exchange (ETDEWEB)

    Soleimani-damaneh, M. [Department of Mathematics, Faculty of Mathematical Science and Computer Engineering, Teacher Training University, 599 Taleghani Avenue, Tehran 15618 (Iran, Islamic Republic of)], E-mail: soleimani_d@yahoo.com

    2008-04-15

    This paper considers the concept of fuzzy upper bounds and provides some relevant applications. Considering a fuzzy DEA model, the existence of a fuzzy upper bound for the objective function of the model is shown and an effective approach to solve that model is introduced. Some dual interpretations are provided, which are useful for practical purposes. Applications of the concept of fuzzy upper bounds in two physical problems are pointed out.

  5. Survey of Hand and Upper Extremity Injuries Among Rock Climbers.

    Science.gov (United States)

    Nelson, Clayton E; Rayan, Ghazi M; Judd, Dustin I; Ding, Kai; Stoner, Julie A

    2017-07-01

    Rock climbing first evolved as a sport in the late 18th century. With its growing popularity, the number of rock climbing-related injuries has potential to increase, spurring a rise in the number of articles associated with it. Despite the available literature, there remains a paucity of information about upper extremity injuries sustained by rock climbers, and no studies to date have focused on gender-specific injuries. A 24-question online survey was distributed to rock climbers about upper extremity injuries sustained during rock climbing. Statistical analysis was used to study association between participants' demographics and injuries. A total of 397 participants responded to the survey. Mean age was 32.5 years with males comprising 85%. No significant differences in demographics or climbing behaviors were found between males and females. Ninety percent of participants reported sustaining an upper extremity injury. Fingers were the most common injury followed by shoulder/arm and elbow/forearm. Our study found females to be more likely to report a rock climbing-related injury, and more likely to undergo surgery for it. Female rock climbers were significantly more likely to report a shoulder/upper arm injury and were also more likely to report undergoing surgery compared with males, where these differences were not due to age or climbing behaviors. Further investigation is warranted into the association between shoulder injuries and female athletes to determine how the gender differences relate to extent of injury as well as health service utilization behaviors.

  6. Contested minorities – the case of Upper Silesia

    Directory of Open Access Journals (Sweden)

    Gierczak Dariusz

    2015-06-01

    Full Text Available Upper Silesia in terms of ethnicity is a typical example of a historical region in Europe, but in fact, one of the few exceptions in contemporary Poland, where its mixed ethnic and religious structures have at least partly survived until today. While their existence had been denied by Nazi Germany (1933-1945 as well as by the Polish People's Republic (1945-1989, the emancipation of the German and Silesian minorities after the democratic changes of 1989 have evoked strong emotions in the ethnically almost uniform country. Nonetheless, the recent situation of minorities has improved as never before. Minority organisations has been officially recognized and German finally has become the second language in some municipalities of Upper Silesia, but the largest ethnic group in the whole country, the Silesians, have still experienced no formal recognition as a national minority. This article deals with the demographic aspects of the ethnic groups in Upper Silesia since the 19th century until recent times. The census results concerning the ethnic minorities or languages in Upper Silesia have been contested since the first records of that kind have been taken. The outcomes of the both last censuses of 2002 and 2011 concerning the minority question reflected for the first time a much more realistic picture of the status quo. Furthermore, they showed that the idea of Silesian identification found an unexpected high number of supporters. This fact indicates an emerging meaning of regional identification amid significant changes of cultural values in Polish society.

  7. Upper plenum mixing in a BWR

    International Nuclear Information System (INIS)

    Alamgir, M.; Andersen, J.G.M.; Parameswaran, V.

    1984-01-01

    A model for the emergency core cooling injection into the upper plenum of a boiling water reactor has been formulated and implemented into the TRACB02 computer program. The model consists of a spray model and a submerged jet model. The submerged jet model is used when the spray nozzles are covered by a two-phase mixture, and the spray model is used when the nozzles are uncovered. The upper plenum model has been assessed by comparison to an upper plenum mixing test in the Steam Sector Test Facility. It is found that the model accurately predicts the phenomena in the upper plenum of a boiling water reactor

  8. Upper gastrointestinal bleeding - state of the art.

    Science.gov (United States)

    Szura, Mirosław; Pasternak, Artur

    2014-01-01

    Upper gastrointestinal (GI) bleeding is a condition requiring immediate medical intervention, with high associated mortality exceeding 10%. The most common cause of upper GI bleeding is peptic ulcer disease, which largely corresponds to the intake of NSAIDs and Helicobacter pylori infection. Endoscopy is the essential tool for the diagnosis and treatment of active upper GI hemorrhage. Endoscopic therapy together with proton pump inhibitors and eradication of Helicobacter pylori significantly reduces rebleeding rates, mortality and number of emergency surgical interventions. This paper presents contemporary data on the diagnosis and treatment of upper gastrointestinal bleeding.

  9. Smartphone supported upper limb prosthesis

    Directory of Open Access Journals (Sweden)

    Hepp D.

    2015-09-01

    Full Text Available State of the art upper limb prostheses offer up to six active DoFs (degrees of freedom and are controlled using different grip patterns. This low number of DoFs combined with a machine-human-interface which does not provide control over all DoFs separately result in a lack of usability for the patient. The aim of this novel upper limb prosthesis is both offering simplified control possibilities for changing grip patterns depending on the patients’ priorities and the improvement of grasp capability. Design development followed the design process requirements given by the European Medical Device Directive 93/42 ECC and was structured into the topics mechanics, software and drive technology. First user needs were identified by literature research and by patient feedback. Consequently, concepts were evaluated against technical and usability requirements. A first evaluation prototype with one active DoF per finger was manufactured. In a second step a test setup with two active DoF per finger was designed. The prototype is connected to an Android based smartphone application. Two main grip patterns can be preselected in the software application and afterwards changed and used by the EMG signal. Three different control algorithms can be selected: “all-day”, “fine” and “tired muscle”. Further parameters can be adjusted to customize the prosthesis to the patients’ needs. First patient feedback certified the prosthesis an improved level of handling compared to the existing devices. Using the two DoF test setup, the possibilities of finger control with a neural network are evaluated at the moment. In a first user feedback test, the smartphone based software application increased the device usability, e.g. the change within preselected grip patterns and the “tired muscle” algorithm. Although the overall software application was positively rated, the handling of the prosthesis itself needs to be proven within a patient study to be

  10. [Temporal meaning of suffering].

    Science.gov (United States)

    Porée, J

    2015-09-01

    If we had to find a few simple words to express what a suffering human being experiences, no matter what ills are causing the suffering and no matter what circumstances underlie the ills themselves, we could unmistakably say that it is the experience of not being able to go on like this. Suffering can be described, in this same sense, as an alteration in temporality. However, describing suffering as such only makes sense if we already have a conception of normal temporality. Yet for this, philosophical tradition offers not one but four competing conceptions. In the present article, we begin by briefly presenting these different conceptions. We then show how each one sheds light, by way of contrast, on a phenomenon whose meaning thus appears to be essentially negative. But does this phenomenon have a negative meaning only? Doesn't it correspond as much to a transformation as an alteration of temporality? This is what we will strive to establish in the third part of the article by relating suffering to hope, in a paradoxical sense of the term. Of the four conceptions of time likely to shed a contrasting light on the upheavals that suffering introduces into our life experience, the one described by Aristotle in Physics is historically the first. In particular, the notion of succession originates therein. But this conception does not account for what makes time the unit of a past, a present, and a future. In Book XI of Confessions, St. Augustine situated this unit not in nature but in the human mind. Hence, his definition of time as a distension of the soul and the necessary division into physical time and psychic time it entails. Husserl's Lessons on the phenomenology of the consciousness of internal time lend credit to this division, but they illuminate only the internal constitution of the "present", which is at the heart of the psychological conception of time. In Being and Time, Heidegger breaks away from this long-standing tradition; in his view, physical time

  11. When Information Conveys Meaning

    Directory of Open Access Journals (Sweden)

    Anthony Reading

    2012-11-01

    Full Text Available While some information is clearly meaningful and some clearly is not, no one has been able to identify exactly what the difference is. The major obstacle has been the way information and meaning are conceptualized: the one in the physical realm of tangible, objective entities and the other in the mental world of intangible, subjective ones. This paper introduces an approach that incorporates both of them within a unified framework by defining them in terms of what they do, rather than what they are. Meaningful information is thus conceptualized here as patterns of matter and energy that have a tangible effect on the entities that detect them, either by changing their function, structure or behavior, while patterns of matter and energy that have no such effects are considered meaningless. The way that meaningful information can act as a causal agent in bio-behavioral systems enables us to move beyond dualistic concepts of ourselves as comprised of a material body that obeys the laws of physics and a non-material essence that is too elusive to study [1].

  12. Estimation of Structure-Borne Noise Reduction Effect of Steel Railway Bridge Equipped with Floating Ladder Track and Floating Reinforced-Concrete Deck

    Science.gov (United States)

    Watanabe, Tsutomu; Sogabe, Masamichi; Asanuma, Kiyoshi; Wakui, Hajime

    A number of steel railway bridges have been constructed in Japan. Thin steel members used for the bridges easily tend to vibrate and generate structure-borne noise. Accordingly, the number of constructions of steel railway bridges tends to decrease in the urban areas from a viewpoint of environmental preservation. Then, as a countermeasure against structure-borne noise generated from steel railway bridges, we have developed a new type of the steel railway bridge equipped with a floating-ladder track and a floating reinforced-concrete (RC) deck. As a result of train-running experiment, it became apparent that the new steel railway bridge installed by double floating system has reduced a vibration velocity level by 10.5 dB(A) at main girder web as compared with a steel railway bridge installed by directly fastened track. This reduction effect was achieved by the ladder track and RC deck supported by resilient materials.

  13. Super-long bridges with floating towers: the role of multi-box decks and Hardware-In-the-Loop technology for wind tunnel tests

    Science.gov (United States)

    Zasso, A.; Argentini, T.; Bayati, I.; Belloli, M.; Rocchi, D.

    2017-12-01

    The super long fjord crossings in E39 Norwegian project pose new challenges to long span bridge design and construction technology. Proposed solutions should consider the adoption of bridge deck with super long spans or floating solutions for at least one of the towers, due to the relevant fjord depth. At the same time, the exposed fjord environment, possibly facing the open ocean, calls for higher aerodynamic stability performances. In relation to this scenario, the present paper addresses two topics: 1) the aerodynamic advantages of multi-box deck sections in terms of aeroelastic stability, and 2) an experimental setup in a wind tunnel able to simulate the aeroelastic bridge response including the wave forcing on the floating.

  14. Bridge deck surface temperature monitoring by infrared thermography and inner structure identification using PPT and PCT analysis methods

    Science.gov (United States)

    Dumoulin, Jean

    2013-04-01

    One of the objectives of ISTIMES project was to evaluate the potentialities offered by the integration of different electromagnetic techniques able to perform non-invasive diagnostics for surveillance and monitoring of transport infrastructures. Among the EM methods investigated, we focused our research and development efforts on uncooled infrared camera techniques due to their promising potential level of dissemination linked to their relative low cost on the market. On the other hand, works were also carried out to identify well adapted implementation protocols and key limits of Pulse Phase Thermography (PPT) and Principal Component Thermography (PCT) processing methods to analyse thermal image sequence and retrieve information about the inner structure. So the first part of this research works addresses infrared thermography measurement when it is used in quantitative mode (not in laboratory conditions) and not in qualitative mode (vision applied to survey). In such context, it requires to process in real time thermal radiative corrections on raw data acquired to take into account influences of natural environment evolution with time, thanks to additional measurements. But, camera sensor has to be enough smart to apply in real time calibration law and radiometric corrections in a varying atmosphere. So, a complete measurement system was studied and developed [1] with low cost infrared cameras available on the market. In the system developed, infrared camera is coupled with other sensors to feed simplified radiative models running, in real time, on GPU available on small PC. The whole measurement system was implemented on the "Musmeci" bridge located in Potenza (Italy). No traffic interruption was required during the mounting of our measurement system. The infrared camera was fixed on top of a mast at 6 m elevation from the surface of the bridge deck. A small weather station was added on the same mast at 1 m under the camera. A GPS antenna was also fixed at the

  15. Congenital hand anomalies in Upper Egypt

    Directory of Open Access Journals (Sweden)

    Tarek Abulezz

    2016-01-01

    Full Text Available Background: Congenital hand anomalies are numerous and markedly variant. Their significance is attributed to the frequent occurrence and their serious social, psychological and functional impacts on patient's life. Patients and Methods: This is a follow-up study of 64 patients with hand anomalies of variable severity. All patients were presented to Plastic Surgery Department of Sohag University Hospital in a period of 24 months. Results: This study revealed that failure of differentiation and duplication deformities were the most frequent, with polydactyly was the most common anomaly encountered. The mean age of presentation was 6 years and female to male ratio was 1.46:1. Hand anomalies were either isolated, associated with other anomalies or part of a syndrome. Conclusion: Incidence of congenital hand anomalies in Upper Egypt is difficult to be estimated due to social and cultural concepts, lack of education, poor registration and deficient medical survey. Management of hand anomalies should be individualised, carefully planned and started as early as possible to achieve the best outcome.

  16. The Meaning of "Magma"

    Science.gov (United States)

    Bartley, J. M.; Glazner, A. F.; Coleman, D. S.

    2016-12-01

    Magma is a fundamental constituent of the Earth, and its properties, origin, evolution, and significance bear on issues ranging from volcanic hazards to planetary evolution. Unfortunately, published usages indicate that the term "magma" means distinctly different things to different people and this can lead to miscommunication among Earth scientists and between scientists and the public. Erupting lava clearly is magma; the question is whether partially molten rock imaged at depth and too crystal-rich to flow should also be called magma. At crystal fractions > 50%, flow can only occur via crystal deformation and solution-reprecipitation. As the solid fraction increases to 90% or more, the material becomes a welded crystal framework with melt in dispersed pores and/or along grain boundaries. Seismic images commonly describe such volumes of a few % melt as magma, yet the rheological differences between melt-rich and melt-poor materials make it vital not to confuse a large rock volume that contains a small melt fraction with melt-rich material. To ensure this, we suggest that "magma" be reserved for melt-rich materials that undergo bulk fluid flow on timescales consonant with volcanic eruptions. Other terms should be used for more crystal-rich and largely immobile partially molten rock (e.g., "crystal mush," "rigid sponge"). The distinction is imprecise but useful. For the press, the public, and even earth scientists who do not study magmatic systems, "magma" conjures up flowing lava; reports of a large "magma" body that contains a few percent melt can engender the mistaken perception of a vast amount of eruptible magma. For researchers, physical processes like crystal settling are commonly invoked to account for features in plutonic rocks, but many such processes are only possible in melt-rich materials.

  17. Report from upper atmospheric science

    International Nuclear Information System (INIS)

    Carignan, G.R.; Roble, R.G.; Mende, S.B.; Nagy, A.F.; Hudson, R.D.

    1989-01-01

    Most of the understanding of the thermosphere resulted from the analysis of data accrued through the Atmosphere Explorer satellites, the Dynamics Explorer 2 satellite, and observations from rockets, balloons, and ground based instruments. However, new questions were posed by the data that have not yet been answered. The mesosphere and lower thermosphere have been less thoroughly studied because of the difficulty of accessibility on a global scale, and many rather fundamental characteristics of these regions are not well understood. A wide variety of measurement platforms can be used to implement various parts of a measurement strategy, but the major thrusts of the International Solar Terrestrial Physics Program would require Explorer-class missions. A remote sensing mission to explore the mesosphere and lower thermosphere and one and two Explorer-type spacecraft to enable a mission into the thermosphere itself would provide the essential components of a productive program of exploration of this important region of the upper atomsphere. Theoretical mission options are explored

  18. Upper gastrointestinal bleeding in patients with CKD.

    Science.gov (United States)

    Liang, Chih-Chia; Wang, Su-Ming; Kuo, Huey-Liang; Chang, Chiz-Tzung; Liu, Jiung-Hsiun; Lin, Hsin-Hung; Wang, I-Kuan; Yang, Ya-Fei; Lu, Yueh-Ju; Chou, Che-Yi; Huang, Chiu-Ching

    2014-08-07

    Patients with CKD receiving maintenance dialysis are at risk for upper gastrointestinal bleeding. However, the risk of upper gastrointestinal bleeding in patients with early CKD who are not receiving dialysis is unknown. The hypothesis was that their risk of upper gastrointestinal bleeding is negatively linked to renal function. To test this hypothesis, the association between eGFR and risk of upper gastrointestinal bleeding in patients with stages 3-5 CKD who were not receiving dialysis was analyzed. Patients with stages 3-5 CKD in the CKD program from 2003 to 2009 were enrolled and prospectively followed until December of 2012 to monitor the development of upper gastrointestinal bleeding. The risk of upper gastrointestinal bleeding was analyzed using competing-risks regression with time-varying covariates. In total, 2968 patients with stages 3-5 CKD who were not receiving dialysis were followed for a median of 1.9 years. The incidence of upper gastrointestinal bleeding per 100 patient-years was 3.7 (95% confidence interval, 3.5 to 3.9) in patients with stage 3 CKD, 5.0 (95% confidence interval, 4.8 to 5.3) in patients with stage 4 CKD, and 13.9 (95% confidence interval, 13.1 to 14.8) in patients with stage 5 CKD. Higher eGFR was associated with a lower risk of upper gastrointestinal bleeding (P=0.03), with a subdistribution hazard ratio of 0.93 (95% confidence interval, 0.87 to 0.99) for every 5 ml/min per 1.73 m(2) higher eGFR. A history of upper gastrointestinal bleeding (Pupper gastrointestinal bleeding risk. In patients with CKD who are not receiving dialysis, lower renal function is associated with higher risk for upper gastrointestinal bleeding. The risk is higher in patients with previous upper gastrointestinal bleeding history and low serum albumin. Copyright © 2014 by the American Society of Nephrology.

  19. Finite-Element Investigation of the Structural Behavior of Basalt Fiber Reinforced Polymer (BFRP- Reinforced Self-Compacting Concrete (SCC Decks Slabs in Thompson Bridge

    Directory of Open Access Journals (Sweden)

    Lingzhu Zhou

    2018-06-01

    Full Text Available The need for a sustainable development and improved whole life performance of concrete infrastructure has led to the requirement of more durable and sustainable concrete bridges alongside accurate predictive analysis tools. Using the combination of Self-Compacting Concrete (SCC with industrial by-products and fiber-reinforced polymer (FRP, reinforcement is anticipated to address the concerns of high carbon footprint and corrosion in traditional steel-reinforced concrete structures. This paper presents a numerical investigation of the structural behavior of basalt fiber-reinforced polymer (BFRP-reinforced SCC deck slabs in a real bridge, named Thompson Bridge, constructed in Northern Ireland, U.K. A non-linear finite element (FE model is proposed by using ABAQUS 6.10 in this study, which is aimed at extending the previous investigation of the field test in Thompson Bridge. The results of this field test were used to validate the accuracy of the proposed finite element model. The results showed good agreement between the test results and the numerical results; more importantly, the compressive membrane action (CMA inside the slabs could be well demonstrated by this FE model. Subsequently, a series of parametric studies was conducted to investigate the influence of different parameters on the structural performance of the deck slabs in Thompson Bridge. The results of the analyses are discussed, and conclusions on the behavior of the SCC deck slabs reinforced by BFRP bars are presented.

  20. Quantification of human upper extremity nerves and fascicular anatomy.

    Science.gov (United States)

    Brill, Natalie A; Tyler, Dustin J

    2017-09-01

    In this study we provide detailed quantification of upper extremity nerve and fascicular anatomy. The purpose is to provide values and trends in neural features useful for clinical applications and neural interface device design. Nerve cross-sections were taken from 4 ulnar, 4 median, and 3 radial nerves from 5 arms of 3 human cadavers. Quantified nerve features included cross-sectional area, minor diameter, and major diameter. Fascicular features analyzed included count, perimeter, area, and position. Mean fascicular diameters were 0.57 ± 0.39, 0.6 ± 0.3, 0.5 ± 0.26 mm in the upper arm and 0.38 ± 0.18, 0.47 ± 0.18, 0.4 ± 0.27 mm in the forearm of ulnar, median, and radial nerves, respectively. Mean fascicular diameters were inversely proportional to fascicle count. Detailed quantitative anatomy of upper extremity nerves is a resource for design of neural electrodes, guidance in extraneural procedures, and improved neurosurgical planning. Muscle Nerve 56: 463-471, 2017. © 2016 Wiley Periodicals, Inc.

  1. Unsedated Flexible Upper Gastrointestinal Endoscopy: Need for ...

    African Journals Online (AJOL)

    Background: To determine the incidence of oxygen desaturation and whether routine oxygen monitoring is necessary during unsedated diagnostic flexible upper gastrointestinal endoscopy. Methods: A prospective study involving 54 consecutive in and out patients who had diagnostic upper gastrointestinal endoscopy at ...

  2. Upper High School Students' Understanding of Electromagnetism

    Science.gov (United States)

    Saglam, Murat; Millar, Robin

    2006-01-01

    Although electromagnetism is an important component of upper secondary school physics syllabuses in many countries, there has been relatively little research on students' understanding of the topic. A written test consisting of 16 diagnostic questions was developed and used to survey the understanding of electromagnetism of upper secondary school…

  3. A Boundary Property for Upper Domination

    KAUST Repository

    AbouEisha, Hassan M.; Hussain, Shahid; Lozin, Vadim; Monnot, Jé rô me; Ries, Bernard; Zamaraev, Viktor

    2016-01-01

    An upper dominating set in a graph is a minimal (with respect to set inclusion) dominating set of maximum cardinality.The problem of finding an upper dominating set is generally NP-hard, but can be solved in polynomial time in some restricted graph

  4. The Upper Atmosphere; Threshold of Space.

    Science.gov (United States)

    Bird, John

    This booklet contains illustrations of the upper atmosphere, describes some recent discoveries, and suggests future research questions. It contains many color photographs. Sections include: (1) "Where Does Space Begin?"; (2) "Importance of the Upper Atmosphere" (including neutral atmosphere, ionized regions, and balloon and investigations); (3)…

  5. Upper urinary tract carcinoma in Lynch syndrome cases.

    Science.gov (United States)

    Crockett, David G; Wagner, David G; Holmäng, Sten; Johansson, Sonny L; Lynch, Henry T

    2011-05-01

    Patients with Lynch syndrome are much more likely to have generally rare upper urinary tract urothelial carcinoma but not bladder urothelial carcinoma. While the risk has been quantified, to our knowledge there is no description of how this population of patients with Lynch syndrome and upper urinary tract cancer differs from the general population with upper urinary tract cancer. We obtained retrospective data on a cohort of patients with Lynch syndrome from the Hereditary Cancer Center in Omaha, Nebraska and compared the data to those on a control general population from western Sweden. These data were supplemented by a new survey about exposure to known risk factors. Of the patients with Lynch syndrome 91% had mutations in MSH2 rather than in MSH1 and 79% showed upper tract urothelial carcinoma a mean of 15.85 years after prior Lynch syndrome-type cancer. Median age at diagnosis was 62 years vs 70 in the general population (p Lynch syndrome 51% had urothelial carcinoma in the ureter while it occurred in the renal pelvis in 65% of the general population (p = 0.0013). Similar numbers of high grade tumors were found in the Lynch syndrome and general populations (88% and 74%, respectively, p = 0.1108). Upper urinary tract tumors develop at a younger age and are more likely to be in the ureter with an almost equal gender ratio in patients with Lynch syndrome. It has high grade potential similar to that in the general population. Copyright © 2011 American Urological Association Education and Research, Inc. Published by Elsevier Inc. All rights reserved.

  6. Enabling factors for antibiotic prescribing for upper respiratory tract infections

    DEFF Research Database (Denmark)

    Jaruseviciene, Lina; Radzeviciene Jurgute, Ruta; Bjerrum, Lars

    2013-01-01

    . This study aimed to explore experiences of GPs in Lithuania and the Russian Federation with regard to antibiotic prescription for upper respiratory tract infections. By such means it might be possible to reveal external enabling factors that influence antibiotic prescribing in these countries. Method. Five...... for political leadership to encourage clinically grounded antibiotic use; over-the-counter sale of antibiotics; designation of antibiotics as reimbursable medications; supervision by external oversight institutions; lack of guidelines for the treatment of upper respiratory tract infections; and pharmaceutical......Abstract Introduction. General practitioners (GPs) write about 80% of all antibiotic prescriptions, the greatest number of them for patients with respiratory tract infections. However, there is a lack of research targeting the influence of external factors on antibiotic prescribing by physicians...

  7. RUNOFF POTENTIAL OF MUREŞ RIVER UPPER BASIN TRIBUTARIES

    Directory of Open Access Journals (Sweden)

    V. SOROCOVSCHI

    2012-03-01

    Full Text Available Runoff Potential of Mureş River Upper Basin Tributaries. The upper basin of the Mureş River includes a significant area of the Eastern Carpathians central western part with different runoff formation conditions. In assessing the average annual runoff potential we used data from six gauging stations and made assessments on three distinct periods. Identifying the appropriate areas of the obtained correlations curves (between specific average runoff and catchments mean altitude allowed the assessment of potential runoff at catchment level and on geographical units. The potential average runoff is also assessed on altitude intervals of the mentioned areas. The runoff potential analysis on hydrographic basins, geographical units and altitude intervals highlights the variant spatial distribution of this general water resources indicator in the different studied areas.

  8. MEANS FOR SHIELDING AND COOLING REACTORS

    Science.gov (United States)

    Wigner, E.P.; Ohlinger, L.A.; Young, G.J.; Weinberg, A.M.

    1959-02-10

    Reactors of the water-cooled type and a means for shielding such a rcactor to protect operating personnel from harmful radiation are discussed. In this reactor coolant tubes which contain the fissionable material extend vertically through a mass of moderator. Liquid coolant enters through the bottom of the coolant tubes and passes upwardly over the fissionable material. A shield tank is disposed over the top of the reactor and communicates through its bottom with the upper end of the coolant tubes. A hydrocarbon shielding fluid floats on the coolant within the shield tank. With this arrangements the upper face of the reactor can be opened to the atmosphere through the two superimposed liquid layers. A principal feature of the invention is that in the event radioactive fission products enter thc coolant stream. imposed layer of hydrocarbon reduces the intense radioactivity introduced into the layer over the reactors and permits removal of the offending fuel material by personnel shielded by the uncontaminated hydrocarbon layer.

  9. Modelling of pavement materials on steel decks using the five-point bending test: Thermo mechanical evolution and fatigue damage

    International Nuclear Information System (INIS)

    Arnaud, L; Houel, A

    2010-01-01

    This paper deals with the modelling of wearing courses on steel orthotropic decks such as the Millau viaduct in France. This is of great importance when dealing with durability: due to the softness of such a support, the pavement is subjected to considerable strains that may generate top-down cracks in the layer at right angles of the orthotropic plate stiffeners and shear cracks at the interface between pavement and steel. Therefore, a five-point bending fatigue test was developed and improved since 2003 at the ENTPE laboratory, to test different asphalt concrete mixes. This study aims at modelling the mechanical behavior of the wearing course throughout the fatigue test by a finite element method (Comsol Multiphysics software). Each material - steel, sealing sheet, asphalt concrete layer - is considered and modelled. The modelling of asphalt concrete is complex since it is a heterogeneous material, a viscoelastic medium and it thermosensitive. The actual characteristics of the asphalt concrete (thermo physical parameter and viscoelastic complex modulus) are determined experimentally on cylindrical cores. Moreover, a damage law based on Miner's damage is included in the model. The modelling of the fatigue test leads to encouraging results. Finally, results from the model are compared to the experimental data obtained from the five-point bending fatigue test device. The experimental data are very consistent with the numerical simulation.

  10. Simulations of Continuous Descent Operations with Arrival-management Automation and Mixed Flight-deck Interval Management Equipage

    Science.gov (United States)

    Callantine, Todd J.; Kupfer, Michael; Martin, Lynne Hazel; Prevot, Thomas

    2013-01-01

    Air traffic management simulations conducted in the Airspace Operations Laboratory at NASA Ames Research Center have addressed the integration of trajectory-based arrival-management automation, controller tools, and Flight-Deck Interval Management avionics to enable Continuous Descent Operations (CDOs) during periods of sustained high traffic demand. The simulations are devoted to maturing the integrated system for field demonstration, and refining the controller tools, clearance phraseology, and procedures specified in the associated concept of operations. The results indicate a variety of factors impact the concept's safety and viability from a controller's perspective, including en-route preconditioning of arrival flows, useable clearance phraseology, and the characteristics of airspace, routes, and traffic-management methods in use at a particular site. Clear understanding of automation behavior and required shifts in roles and responsibilities is important for controller acceptance and realizing potential benefits. This paper discusses the simulations, drawing parallels with results from related European efforts. The most recent study found en-route controllers can effectively precondition arrival flows, which significantly improved route conformance during CDOs. Controllers found the tools acceptable, in line with previous studies.

  11. The Impact of Traffic-Induced Bridge Vibration on Rapid Repairing High-Performance Concrete for Bridge Deck Pavement Repairs

    Directory of Open Access Journals (Sweden)

    Wei Wang

    2014-01-01

    Full Text Available Based on forced vibration tests for high-performance concrete (HPC, the influence of bridge vibration induced by traveling vehicle on compressive strength and durability of HPC has been studied. It is concluded that 1 d and 2 d compressive strength of HPC decreased significantly, and the maximum reduction rate is 9.1%, while 28 d compressive strength of HPC had a slight lower with a 3% maximal drop under the action of two simple harmonic vibrations with 2 Hz, 3 mm amplitude, and 4 Hz, 3 mm amplitude. Moreover, the vibration had a slight effect on the compressive strength of HPC when the simple harmonic vibration had 4 Hz and 1 mm amplitude; it is indicated that the amplitude exerts a more prominent influence on the earlier compressive strength with the comparison of the frequency. In addition, the impact of simple harmonic vibration on durability of HPC can be ignored; this shows the self-healing function of concrete resulting from later hydration reaction. Thus, the research achievements mentioned above can contribute to learning the laws by which bridge vibration affects the properties of concrete and provide technical support for the design and construction of the bridge deck pavement maintenance.

  12. Upper Higgs boson mass bounds from a chirally invariant lattice Higgs-Yukawa Model

    Energy Technology Data Exchange (ETDEWEB)

    Gerhold, P. [Humboldt-Universitaet, Berlin (Germany). Inst. fuer Physik; John von Neumann-Institut fuer Computing NIC/DESY, Zeuthen (Germany); Jansen, K. [John von Neumann-Institut fuer Computing NIC/DESY, Zeuthen (Germany)

    2010-02-15

    We establish the cutoff-dependent upper Higgs boson mass bound by means of direct lattice computations in the framework of a chirally invariant lattice Higgs-Yukawa model emulating the same chiral Yukawa coupling structure as in the Higgs-fermion sector of the Standard Model. As expected from the triviality picture of the Higgs sector, we observe the upper mass bound to decrease with rising cutoff parameter {lambda}. Moreover, the strength of the fermionic contribution to the upper mass bound is explored by comparing to the corresponding analysis in the pure {phi}{sup 4}-theory. (orig.)

  13. Influence of ceiling systems on room temperature and energy efficiency in steel sheet deckings; Einfluss von Deckensystemen auf Raumtemperatur und Energieeffizienz im Stahlgeschossbau

    Energy Technology Data Exchange (ETDEWEB)

    Doering, Bernd

    2008-07-01

    Over the past years the use of flooring systems to affect the indoor climate of buildings is of increasing interest, including both thermo-active and also passive systems. The amendment of the German Energy saving ordinance (Energieeinsparverordnung 2007) requires, that in future projects, the energy demand for cooling and ventilation has to be considered for the calculation of the energy demand of non-residential buildings. Due to this circumstance, solutions for energy efficient cooling will come more into the focus. Up to now, the use of flooring systems in steel structures have not been investigated regarding this aspect. In this thesis, six different flooring systems were investigated: two passive acting solutions, using the effects of enlarging the surface and integrating phase change materials (PCM), one system comprising ducts that pass cold air through the floor during the night and three thermo-active deck systems (i.e. profiled steel sheet decking, a hollow-core slab, and a laser-welded steel sandwich panel). Generally, the thermal behaviour of such elements is described only using one-dimensional multilayer structure (for standardized calculations or for thermal building simulation), this concept is not adequate for profiled and homogeneous components. Therefore three-dimensional Finite Elemente investigations were performed to consider the specific properties. Based on these results a simplified method using equivalent parameters was developed, which allows the implementation of the considered flooring systems in standardized calculations (ISO 13786). For selected systems, validation by in-service measurements was performed. By using Thermal Building Simulation tools, a parametric study was carried out to specify the range and limits of application in respect of climate and internal heat gains. The results can be summarized as follows: - Profiled steel sheet decking show a higher effective thermal capacity than conventional flat slabs. - PCM increases

  14. Upper gastrointestinal symptoms in patients with advanced cancer: relationship to nutritional and performance status.

    Science.gov (United States)

    Bovio, G; Montagna, G; Bariani, C; Baiardi, P

    2009-10-01

    The goals of the study were to determine the relationship of upper gastrointestinal symptoms with nutritional status and to assess their association with performance status in patients with advanced cancer. We studied 143 patients (50 F, 93 M, mean age 68 +/- 11 years, mean body mass index 22.39 +/- 4.3 kg/m(2)). Assessed symptoms were the following: anorexia, nausea, vomiting, dysphagia for solids, dysphagia for liquids, xerostomia, hypogeusia, dysgeusia, hiccup and chewing disturbances. We determined anthropometric parameters, daily energy intake and serum albumin, prealbumin and transferrin. The most common upper gastrointestinal symptoms were xerostomia (73%), anorexia (49%) and chewing disturbances (40%). Fifty-four percent of patients had weight loss greater than 10%. Seventy-three patients (51%) had daily energy intake lower than their resting energy expenditure. Mean serum prealbumin, albumin and transferrin were below normal range. Mean Eastern Cooperative Oncology Group performance status scale was 3.1 +/- 0.49. Symptoms were often strongly correlated, and usually, patients experienced at least three upper gastrointestinal symptoms at the same time. Anorexia, nausea and vomiting were the symptoms mostly correlated with other symptoms. A correlation was found between vomiting and hiccup. Energy intake (EI) was the nutritional parameter mostly affected by upper gastrointestinal symptoms; moreover, EI is the most predictive factor of upper gastrointestinal symptoms, particularly xerostomia, anorexia and dysphagia for solids. Upper gastrointestinal symptoms are linked to nutritional parameters: In particular, energy intake represents the most predictive variable of symptom occurrence. The performance status is not affected by upper gastrointestinal symptoms. A rigorous nutritional assessment and the managing of upper gastrointestinal symptoms are crucial in patients with advanced cancer.

  15. Accuracy and precision of flash glucose monitoring sensors inserted into the abdomen and upper thigh compared with the upper arm.

    Science.gov (United States)

    Charleer, Sara; Mathieu, Chantal; Nobels, Frank; Gillard, Pieter

    2018-06-01

    Nowadays, most Belgian patients with type 1 diabetes use flash glucose monitoring (FreeStyle Libre [FSL]; Abbott Diabetes Care, Alameda, California) to check their glucose values, but some patients find the sensor on the upper arm too visible. The aim of the present study was to compare the accuracy and precision of FSL sensors when placed on different sites. A total of 23 adults with type 1 diabetes used three FSL sensors simultaneously for 14 days on the upper arm, abdomen and upper thigh. FSL measurements were compared with capillary blood glucose (BG) measurements obtained with a built-in FSL BG meter. The aggregated mean absolute relative difference was 11.8 ± 12.0%, 18.5 ± 18.4% and 12.3 ± 13.8% for the arm, abdomen (P = .002 vs arm) and thigh (P = .5 vs arm), respectively. Results of Clarke error grid analysis for the arm and thigh were similar (zone A: 84.9% vs 84.5%; P = .6), while less accuracy was seen for the abdomen (zone A: 69.4%; P = .01). Apart from the first day, the accuracy of FSL sensors on the arm and thigh was more stable across the 14-day wear duration than accuracy of sensors on the abdomen, which deteriorated mainly during week 2 (P < .0005). The aggregated precision absolute relative difference was markedly lower for the arm/thigh (10.9 ± 11.9%) compared with the arm/abdomen (20.9 ± 22.8%; P = .002). Our results indicate that the accuracy and precision of FSL sensors placed on the upper thigh are similar to the upper arm, whereas the abdomen performed unacceptably poorly. © 2018 John Wiley & Sons Ltd.

  16. [The "window" surgical exposure strategy of the upper anterior cervical retropharyngeal approach for anterior decompression at upper cervical spine].

    Science.gov (United States)

    Wu, Xiang-Yang; Zhang, Zhe; Wu, Jian; Lü, Jun; Gu, Xiao-Hui

    2009-11-01

    To investigate the "window" surgical exposure strategy of the upper anterior cervical retropharyngeal approach for the exposure and decompression and instrumentation of the upper cervical spine. From Jan. 2000 to July 2008, 5 patients with upper cervical spinal injuries were treated by surgical operation included 4 males and 1 female with and average age of 35 years old ranging from 16 to 68 years. There were 2 cases of Hangman's fractures (type II ), 2 of C2.3 intervertebral disc displacement and 1 of C2 vertebral body tuberculosis. All patients underwent the upper cervical anterior retropharyngeal approach through the "window" between the hypoglossal nerve and the superior laryngeal nerve and pharynx and carotid artery. Two patients of Hangman's fractures underwent the C2,3 intervertebral disc discectomy, bone graft fusion and internal fixation. Two patients of C2,3 intervertebral disc displacement underwent the C2,3 intervertebral disc discectomy, decompression bone graft fusion and internal fixation. One patient of C2 vertebral body tuberculosis was dissected and resected and the focus and the cavity was filled by bone autografting. C1 anterior arch to C3 anterior vertebral body were successful exposed. Lesion resection or decompression and fusion were successful in all patients. All patients were followed-up for from 5 to 26 months (means 13.5 months). There was no important vascular and nerve injury and no wound infection. Neutral symptoms was improved and all patient got successful fusion. The "window" surgical exposure surgical technique of the upper cervical anterior retropharyngeal approach is a favorable strategy. This approach strategy can be performed with full exposure for C1-C3 anterior anatomical structure, and can get minimally invasive surgery results and few and far between wound complication, that is safe if corresponding experience is achieved.

  17. Evaluation of postoperative patient satisfaction after covering the nasal dorsum with upper lateral cartilage: "upper lateral closing".

    Science.gov (United States)

    Çağıcı, Can Alper

    2017-11-16

    Following nasal hump removal during septorhinoplasty, the middle vault should be reconstructed to avoid functional and esthetic problems. Middle vault reconstruction, however, may result in widening of the middle vault and may need a camouflage graft to cover dorsal irregularities. To present the results of reconstructing the middle vault with a technique that covers the nasal dorsum with upper lateral cartilage, from the viewpoint of patient satisfaction. Retrospective study of patients who underwent septorhinoplasty that included nasal dorsum closure with upper lateral cartilage from December 1, 2014 to January 31, 2016. Those with postoperative follow-up of less than 3 months were excluded. The final study group included 39 patients. The same surgeon performed all septorhinoplasties. The dorsum was closed using an "upper lateral closing" technique that approximated upper lateral cartilages to each other over the septum. Postoperative patient satisfaction was determined using a visual analog scale and the rhinoplasty outcomes evaluation questionnaire. The questionnaire evaluates patient esthetic and functional satisfaction with the operated nose. High scores indicate improved esthetic results. No dorsal irregularities were seen at postoperative follow-up evaluation of the patients. For esthetic nasal appearance, the median visual analogue scale scores was 86%, and the mean for the questionnaire was 77.03%. The natural dome-shaped anatomy of the nasal dorsum was achieved by approximating the upper lateral cartilages to each other. Closing the dorsum with this technique also covers any dorsal irregularities and results in a smooth dorsum. Patients expressed satisfaction with the esthetic and functional aspects of the smooth, attractive nasal dorsum. Copyright © 2017 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. Published by Elsevier Editora Ltda. All rights reserved.

  18. Lateral chest radiographic findings in lobar collapse of the left lung : the distance between both upper lobe bronchi

    International Nuclear Information System (INIS)

    Chin, G. H.; Sung, D. W.; Yoon, Y.; Kim, H. C.

    1996-01-01

    To evaluate the distance between both upper love bronchi on lateral radiographs and its change in left upper or lower lobe collapse. 144 true lateral radiographs were analyzed on which both upper lobe bronchi were clearly identified. They included 116 normal cases, 11 cases of left upper lobe collapse, 13 of left lower lobe collapse, and 4 cases of left lower lobe lobectomy. Line A was drawn parallel to the vertebral end plate through the upper margin of the lift upper lobe bronchus. Line B was drawn parallel to line A through the upper margin of the right upper love bronchus. The shortest distance between line A and line B was measured as the distance between both upper lobe bronchi. In normal cases, the mean value of the distance was 2.19 cm ± S.D. 0.37 cm on right and on right and 2.16 cm ± S.D. 0.40 cm on left lateral radiographs ; these results were not significantly different(P=0.79). In cases of collapse, the mean value of the distance was 0.43 cm ± S.D. 0.99 cm in upper lobe collapse and 3.56 cm ± S.D. 0.72 cm in lower lobe collapse, results which were significantly different from those of normal cases(p<0.01). In eight cases(73%) of left upper lobe collapse, the distance was less than 1 cm and in 10 cases(77%) of left lower lobe collapse, the distance was more than 3 cm. The distance between both upper lobe bronchi varies markedly in case of lobar collapse. A distance of less than 1 cm suggests collapse of the left upper lobe and a distance more than 3 cm suggests collapse of the left lower lobe

  19. Stochastic analysis and robust optimization for a deck lid inner panel stamping

    International Nuclear Information System (INIS)

    Hou, Bo; Wang, Wurong; Li, Shuhui; Lin, Zhongqin; Xia, Z. Cedric

    2010-01-01

    FE-simulation and optimization are widely used in the stamping process to improve design quality and shorten development cycle. However, the current simulation and optimization may lead to non-robust results due to not considering the variation of material and process parameters. In this study, a novel stochastic analysis and robust optimization approach is proposed to improve the stamping robustness, where the uncertainties are involved to reflect manufacturing reality. A meta-model based stochastic analysis method is developed, where FE-simulation, uniform design and response surface methodology (RSM) are used to construct meta-model, based on which Monte-Carlo simulation is performed to predict the influence of input parameters variation on the final product quality. By applying the stochastic analysis, uniform design and RSM, the mean and the standard deviation (SD) of product quality are calculated as functions of the controllable process parameters. The robust optimization model composed of mean and SD is constructed and solved, the result of which is compared with the deterministic one to show its advantages. It is demonstrated that the product quality variations are reduced significantly, and quality targets (reject rate) are achieved under the robust optimal solution. The developed approach offers rapid and reliable results for engineers to deal with potential stamping problems during the early phase of product and tooling design, saving more time and resources.

  20. Overestimation of Knowledge about Word Meanings: The "Misplaced Meaning" Effect

    Science.gov (United States)

    Kominsky, Jonathan F.; Keil, Frank C.

    2014-01-01

    Children and adults may not realize how much they depend on external sources in understanding word meanings. Four experiments investigated the existence and developmental course of a "Misplaced Meaning" (MM) effect, wherein children and adults overestimate their knowledge about the meanings of various words by underestimating how much…

  1. Delaware River and Upper Bay Sediment Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The area of coverage consists of 192 square miles of benthic habitat mapped from 2005 to 2007 in the Delaware River and Upper Delaware Bay. The bottom sediment map...

  2. Climate influences on upper Limpopo River flow

    African Journals Online (AJOL)

    2016-01-01

    Jan 1, 2016 ... Keywords: Limpopo Valley, hydro-meteorology, surface water deficit. * To whom all ... millenia and there is a history of drought impacts on vegetation. (Ekblom et ... water budget of the upper Limpopo River valley using direct.

  3. γ -phlebography of the upper limbs

    International Nuclear Information System (INIS)

    Jacolot, G.; Legendre, P.; Millour, L.; Barra, J.A.; Perramant, M.; Morin, P.P.

    1981-01-01

    γ-phlebography is an easy and repetitive exploration of deep venous thrombosis. This investigation becomes very useful for the upper limbs on account of the present frequency of iatrogenic thrombosis [fr

  4. Lathlike upper bainite in a silicon steel

    International Nuclear Information System (INIS)

    Liu Cheng; Zhao Zhenbo; Bhole, S.D.

    2006-01-01

    The morphology and mechanical properties of upper bainite formed isothermally at 400 deg. C for different holding times in a 1.83 wt.% silicon steel have been investigated by optical metallograph, X-ray diffraction and transmission electron microscopy (TEM). In the early stage of upper bainitic transformation, lathlike bainite whose individual lath ferrite is separated by the thin film type of retained austenite is obtained. As the isothermal holding times are increased, the blocky region consisting of retained austenite and martensite is also found. The stability of retained austenite in lathlike upper bainite is studied in relation to the isothermal treatment times, and the heat treatment conditions. The results show that an optimum combination of strength and ductility is attributed to the formation of bainitic ferrite (BF) and a large amount of thin film carbon-enriched retained austenite in the upper bainite

  5. upper gastrointestinal endoscopy findings in patients referred

    African Journals Online (AJOL)

    2014-08-01

    Aug 1, 2014 ... Objective: To determine the pattern of referral and endoscopy ... build a model of a flexible fibre imaging device (2) ..... a retrospective and prospective audit of all upper ... endoscopy should be reserved for the high risk.

  6. Parametric decay below the upper hybrid frequency

    Energy Technology Data Exchange (ETDEWEB)

    Albers, E; Krause, K; Schlueter, H [Bochum Univ. (Germany, F.R.). Inst. fuer Experimentalphysik 2

    1977-03-21

    Parametric decay of the upper hybrid mode is observed between the electron cyclotron frequency and its first two harmonics. The decay products are identified as electron Bernstein and ion acoustic mode. The diagnostic results confirm the relevant dispersion relations.

  7. An approach to the painful upper limb

    African Journals Online (AJOL)

    Pain in the upper limb is a common presenting complaint in the primary health care setting and the ... disruptions or pathological fracture, as opposed to ... and a neurological assessment of the lower limbs. This is in addition to a thorough.

  8. CASE STUDY CRITIQUE; UPPER CLINCH CASE STUDY

    Science.gov (United States)

    Case study critique: Upper Clinch case study (from Research on Methods for Integrating Ecological Economics and Ecological Risk Assessment: A Trade-off Weighted Index Approach to Integrating Economics and Ecological Risk Assessment). This critique answers the questions: 1) does ...

  9. Appropriateness of Referrals for Upper Gastrointestinal Endoscopy ...

    African Journals Online (AJOL)

    Appropriateness of Referrals for Upper Gastrointestinal Endoscopy. ... Accra between January and December, 2008 were interviewed and evaluated for this study. ... Presentations with bleeding and suspicion of malignancy showed statistical ...

  10. Endometrioid carcinoma of the upper urinary tract

    Directory of Open Access Journals (Sweden)

    Kulkarni Jagdeesh

    2010-01-01

    Full Text Available Herein, we report a second case of endometrioid carcinoma of the upper urinary tract presenting 17 years after hysterectomy for high grade adenocarcinoma of ovary. A 51-year-old nullipara presented to us with a complaint of hematuria. After complete work up, she underwent right radical nephro-ureterectomy with bladder cuff excision. The histology showed endometrioid carcinoma of upper urinary tract without any evidence of endometriosis.

  11. Means of Hilbert space operators

    CERN Document Server

    Hiai, Fumio

    2003-01-01

    The monograph is devoted to a systematic study of means of Hilbert space operators by a unified method based on the theory of double integral transformations and Peller's characterization of Schur multipliers. General properties on means of operators such as comparison results, norm estimates and convergence criteria are established. After some general theory, special investigations are focused on three one-parameter families of A-L-G (arithmetic-logarithmic-geometric) interpolation means, Heinz-type means and binomial means. In particular, norm continuity in the parameter is examined for such means. Some necessary technical results are collected as appendices.

  12. Balneotherapy in treatment of spastic upper limb after stroke.

    Science.gov (United States)

    Erceg-Rukavina, Tatjana; Stefanovski, Mihajlo

    2015-02-01

    After stroke, spasticity is often the main problem that prevents functional recovery. Pain occurs in up to 70% of patients during the first year post-stroke. A total of 70 patients (30 female and 45 male) mean age (65.67) participated in prospective, controlled study. ischaemic stroke, developed spasticity of upper limb, post-stroke interval balneotherapy and inability to follow commands. Experimental group (Ex) (n=35) was treated with sulphurous baths (31°-33°C) and controlled group (Co) with taped water baths, during 21 days. All patients were additionally treated with kinesitherapy and cryotherapy. The outcome was evaluated using Modified Ashworth scale for spasticity and VAS scale for pain. The significance value was sat at pbalneotherapy with sulphurous bath on spasticity and pain in affected upper limb. Reduction in tone of affected upper limb muscles was significant in Ex group (pbalneotherapy with sulphurous water reduces spasticity and pain significantly and can help in treatment of post-stroke patients.

  13. Upper airway morphology in Down Syndrome patients under dexmedetomidine sedation

    Directory of Open Access Journals (Sweden)

    Rajeev Subramanyam

    Full Text Available Abstract Background and objectives: Children with Down Syndrome are vulnerable to significant upper airway obstruction due to relative macroglossia and dynamic airway collapse. The objective of this study was to compare the upper airway dimensions of children with Down Syndrome and obstructive sleep apnea with normal airway under dexmedetomidine sedation. Methods: IRB approval was obtained. In this retrospective study, clinically indicated dynamic sagittal midline magnetic resonance images of the upper airway were obtained under low (1 mcg/kg/h and high (3 mcg/kg/h dose dexmedetomidine. Airway anteroposterior diameters and sectional areas were measured as minimum and maximum dimensions by two independent observers at soft palate (nasopharyngeal airway and at base of the tongue (retroglossal airway. Results and conclusions: Minimum anteroposterior diameter and minimum sectional area at nasopharynx and retroglossal airway were significantly reduced in Down Syndrome compared to normal airway at both low and high dose dexmedetomidine. However, there were no significant differences between low and high dose dexmedetomidine in both Down Syndrome and normal airway. The mean apnea hypopnea index in Down Syndrome was 16 ± 11. Under dexmedetomidine sedation, children with Down Syndrome and obstructive sleep apnea when compared to normal airway children show significant reductions in airway dimensions most pronounced at the narrowest points in the nasopharyngeal and retroglossal airways.

  14. Endoscopic evaluation of upper and lower gastro-intestinal bleeding

    Directory of Open Access Journals (Sweden)

    Emeka Ray-Offor

    2015-01-01

    Full Text Available Introduction: A myriad of pathologies lead to gastro-intestinal bleeding (GIB. The common clinical presentations are hematemesis, melena, and hematochezia. Endoscopy aids localization and treatment of these lesions. Aims: The aim was to study the differential diagnosis of GIB emphasizing the role of endoscopy in diagnosis and treatment of GIB. Patients and Methods: A prospective study of patients with GIB referred to the Endoscopy unit of two health facilities in Port Harcourt Nigeria from February 2012 to August 2014. The variables studied included: Demographics, clinical presentation, risk score, endoscopic findings, therapeutic procedure, and outcome. Data were collated and analyzed using SPSS version 20 software. Results: A total of 159 upper and lower gastro-intestinal (GI endoscopies were performed during the study period with 59 cases of GI bleeding. There were 50 males and 9 females with an age range of 13-86 years (mean age 52.4 ΁ 20.6 years. The primary presentations were hematochezia, hematemesis, and melena in 44 (75%, 9 (15%, and 6 (10% cases, respectively. Hemorrhoids were the leading cause of lower GIB seen in 15 cases (41%. The majority of pathologies in upper GIB were seen in the stomach (39%: Gastritis and benign gastric ulcer. Injection sclerotherapy was successfully performed in the hemorrhoids and a case of gastric varices. The mortality recorded was 0%. Conclusion: Endoscopy is vital in the diagnosis and treatment of GIB. Gastritis and Haemorrhoid are the most common causes of upper and lower GI bleeding respectively, in our environment

  15. Demographic characteristics of MS patients in Poland's upper Silesia region.

    Science.gov (United States)

    Pierzchala, Krystyna; Adamczyk-Sowa, Monika; Dobrakowski, Pawel; Kubicka-Baczyk, Katarzyna; Niedziela, Natalia; Sowa, Pawel

    2015-05-01

    In Poland, no national registry of MS patients has yet been introduced. So far, no demographic studies have been conducted in patients with MS in Upper Silesia. The aim of the present study was to evaluate, for the first time, a selected demographic and clinical parameters in MS patients from the Upper Silesia region and compare these characteristics with previously published data from other regions of Poland. 640 patients with clinically defined MS, were prospectively and randomly selected for the study. Social, socio-economic, and demographic data were obtained through a questionnaire study. All subjects performed a self-assessment of their health condition using EQ-5D and EQ-VAS version questionnaires. The ratio of women to men was 2.18. The average age of onset was 29.6 ± 11.1 years; the disease duration was 7.9 ± 4.5 years. The relapsing-remitting form of MS was diagnosed in 73.12%. In 71.25% the onset was monofocal and in 28.75% multifocal disease onset was observed. Among the studied population 339 (52.97%) patients were still employed. A mean EQ-VAS score of 66.11 ± 20.12 was calculated. Results from our study identify for the first time the demographic and clinical characteristics of the Upper Silesia MS population.

  16. Upper airway morphology in Down Syndrome patients under dexmedetomidine sedation.

    Science.gov (United States)

    Subramanyam, Rajeev; Fleck, Robert; McAuliffe, John; Radhakrishnan, Rupa; Jung, Dorothy; Patino, Mario; Mahmoud, Mohamed

    2016-01-01

    Children with Down Syndrome are vulnerable to significant upper airway obstruction due to relative macroglossia and dynamic airway collapse. The objective of this study was to compare the upper airway dimensions of children with Down Syndrome and obstructive sleep apnea with normal airway under dexmedetomidine sedation. IRB approval was obtained. In this retrospective study, clinically indicated dynamic sagittal midline magnetic resonance images of the upper airway were obtained under low (1mcg/kg/h) and high (3mcg/kg/h) dose dexmedetomidine. Airway anteroposterior diameters and sectional areas were measured as minimum and maximum dimensions by two independent observers at soft palate (nasopharyngeal airway) and at base of the tongue (retroglossal airway). Minimum anteroposterior diameter and minimum sectional area at nasopharynx and retroglossal airway were significantly reduced in Down Syndrome compared to normal airway at both low and high dose dexmedetomidine. However, there were no significant differences between low and high dose dexmedetomidine in both Down Syndrome and normal airway. The mean apnea hypopnea index in Down Syndrome was 16±11. Under dexmedetomidine sedation, children with Down Syndrome and obstructive sleep apnea when compared to normal airway children show significant reductions in airway dimensions most pronounced at the narrowest points in the nasopharyngeal and retroglossal airways. Copyright © 2015 Sociedade Brasileira de Anestesiologia. Published by Elsevier Editora Ltda. All rights reserved.

  17. [Upper airway morphology in Down Syndrome patients under dexmedetomidine sedation].

    Science.gov (United States)

    Subramanyam, Rajeev; Fleck, Robert; McAuliffe, John; Radhakrishnan, Rupa; Jung, Dorothy; Patino, Mario; Mahmoud, Mohamed

    2016-01-01

    Children with Down Syndrome are vulnerable to significant upper airway obstruction due to relative macroglossia and dynamic airway collapse. The objective of this study was to compare the upper airway dimensions of children with Down Syndrome and obstructive sleep apnea with normal airway under dexmedetomidine sedation. IRB approval was obtained. In this retrospective study, clinically indicated dynamic sagittal midline magnetic resonance images of the upper airway were obtained under low (1mcg/kg/h) and high (3mcg/kg/h) dose dexmedetomidine. Airway anteroposterior diameters and sectional areas were measured as minimum and maximum dimensions by two independent observers at soft palate (nasopharyngeal airway) and at base of the tongue (retroglossal airway). Minimum anteroposterior diameter and minimum sectional area at nasopharynx and retroglossal airway were significantly reduced in Down Syndrome compared to normal airway at both low and high dose dexmedetomidine. However, there were no significant differences between low and high dose dexmedetomidine in both Down Syndrome and normal airway. The mean apnea hypopnea index in Down Syndrome was 16±11. Under dexmedetomidine sedation, children with Down Syndrome and obstructive sleep apnea when compared to normal airway children show significant reductions in airway dimensions most pronounced at the narrowest points in the nasopharyngeal and retroglossal airways. Copyright © 2015 Sociedade Brasileira de Anestesiologia. Publicado por Elsevier Editora Ltda. All rights reserved.

  18. Aircraft Configuration and Flight Crew Compliance with Procedures While Conducting Flight Deck Based Interval Management (FIM) Operations

    Science.gov (United States)

    Shay, Rick; Swieringa, Kurt A.; Baxley, Brian T.

    2012-01-01

    Flight deck based Interval Management (FIM) applications using ADS-B are being developed to improve both the safety and capacity of the National Airspace System (NAS). FIM is expected to improve the safety and efficiency of the NAS by giving pilots the technology and procedures to precisely achieve an interval behind the preceding aircraft by a specific point. Concurrently but independently, Optimized Profile Descents (OPD) are being developed to help reduce fuel consumption and noise, however, the range of speeds available when flying an OPD results in a decrease in the delivery precision of aircraft to the runway. This requires the addition of a spacing buffer between aircraft, reducing system throughput. FIM addresses this problem by providing pilots with speed guidance to achieve a precise interval behind another aircraft, even while flying optimized descents. The Interval Management with Spacing to Parallel Dependent Runways (IMSPiDR) human-in-the-loop experiment employed 24 commercial pilots to explore the use of FIM equipment to conduct spacing operations behind two aircraft arriving to parallel runways, while flying an OPD during high-density operations. This paper describes the impact of variations in pilot operations; in particular configuring the aircraft, their compliance with FIM operating procedures, and their response to changes of the FIM speed. An example of the displayed FIM speeds used incorrectly by a pilot is also discussed. Finally, this paper examines the relationship between achieving airline operational goals for individual aircraft and the need for ATC to deliver aircraft to the runway with greater precision. The results show that aircraft can fly an OPD and conduct FIM operations to dependent parallel runways, enabling operational goals to be achieved efficiently while maintaining system throughput.

  19. Adverse effects of anticoagulation treatment: clinically significant upper gastrointestinal hemorrhage

    Directory of Open Access Journals (Sweden)

    Pavel Skok

    2006-12-01

    Full Text Available Background: Over the last years, the use of oral anticoagulant treatment has increased dramatically, principally for the prevention of venous thrombosis and thrombembolic events. This treatment is demanding, especially among the elderly with concommitant diseases and different medication. Aim of the study to evaluate the rate of serious complications, clinically significant hemorrhage from upper gastointestinal tract in patients treated with oral antiocoagulants in a prospective cohort study.Patients and methods: Included were patients admitted to our institution between January 1, 1994 and December 31, 2003 due to gastrointestinal hemorrhage. Emergency endoscopy and laboratory testing was performed in all patients.Results: 6416 patients were investigated: 2452 women (38.2 % and 3964 men (61.8 %, mean age 59.1 years, SD 17.2. Among our patients, 55 % were aged over 60 years. In 86.4 % of patients the source of bleeding was confirmed in the upper gastrointestinal tract. In the last week prior to bleeding, 20.4 % (1309/6416 of all patients were regularly taking nonsteroidal anti-inflammatory drugs, anticoagulant therapy or antiplatelet agents in single daily doses at least. 6.3 % of patients (82/1309 with abundant hemorrhage from upper gastrointestinal tract were using oral anticoagulant therapy and had INR > 5 at admission, 25.6 % of them had INR > 10. The mortality of patients using oral anticoagulants and INR > 5 was 17.1 %.Conclusions: Upper gastrointestinal hemorrhage is a serious complication of different medications, particularly in elderly patients. Safe use of anticoagulant therapy is based on careful selection of patients and correct intake of the prescribed drugs.

  20. Culture as meaning-making

    OpenAIRE

    Lenkauskienė, Rūta; Liubinienė, Vilmantė

    2002-01-01

    The present paper analyses the role of social and cultural background knowledge in the cognition of meaning. Language and culture integrated studies have long been in the focus of attention. In order to study the language of a target culture, one should understand how human beings construct meanings, understand processes of meaning-making, account for different meanings, and examine their effects in social life. The language cannot be interpreted in the right way without taking the target cul...

  1. Court interpreting and pragmatic meaning

    DEFF Research Database (Denmark)

    Jacobsen, Bente

    In Denmark, court interpreters are required to deliver verbatim translations of speakers' originals and to refrain from transferring pragmatic meaning. Yet, as this paper demonstrates, pragmatic meaning is central to courtroom interaction.......In Denmark, court interpreters are required to deliver verbatim translations of speakers' originals and to refrain from transferring pragmatic meaning. Yet, as this paper demonstrates, pragmatic meaning is central to courtroom interaction....

  2. Upper limb contributions to frontal plane balance control in rollator-assisted walking.

    Science.gov (United States)

    Tung, James Y; Gage, William H; Poupart, Pascal; McIlroy, William E

    2014-01-01

    While assisting with balance is a primary reason for rollator use, few studies have examined how the upper limbs are used for balance. This study examines upper limb contributions to balance control during rollator-assisted walking. We hypothesized that there would be an increased upper limb contribution, measured by mean vertical loading (Fz) and variation in frontal plane center-of-pressure (COPhigh), when walking balance is challenged/impaired. Experiment 1 compared straight-line and beam-walking in young adults (n = 11). As hypothesized, Fz and COPhighincreased in beam-walking compared to baseline (mean Fz: 13.7 vs. 9.1% body weight (BW), p < 0.001, RMS COPhigh: 1.35 vs. 1.07 cm, p < 0.001). Experiment 2 compared older adults who regularly use rollators (RU, n = 10) to older adult controls (CTL, n = 10). The predicted higher upper limb contribution in the RU group was not supported. However, when individuals were grouped by balance impairment, those with the lowest Berg Balance scores (< 45) demonstrated greater speed-adjusted COPhigh than those with higher scores (p = 0.013). Furthermore, greater COPhigh and Fz were correlated to greater reduction in step width, supporting the role of upper limb contributions to frontal plane balance. This work will guide studies assessing reliance on rollators by providing a basis for measurement of upper limb balance contributions.

  3. ON COMPUTING UPPER LIMITS TO SOURCE INTENSITIES

    International Nuclear Information System (INIS)

    Kashyap, Vinay L.; Siemiginowska, Aneta; Van Dyk, David A.; Xu Jin; Connors, Alanna; Freeman, Peter E.; Zezas, Andreas

    2010-01-01

    A common problem in astrophysics is determining how bright a source could be and still not be detected in an observation. Despite the simplicity with which the problem can be stated, the solution involves complicated statistical issues that require careful analysis. In contrast to the more familiar confidence bound, this concept has never been formally analyzed, leading to a great variety of often ad hoc solutions. Here we formulate and describe the problem in a self-consistent manner. Detection significance is usually defined by the acceptable proportion of false positives (background fluctuations that are claimed as detections, or Type I error), and we invoke the complementary concept of false negatives (real sources that go undetected, or Type II error), based on the statistical power of a test, to compute an upper limit to the detectable source intensity. To determine the minimum intensity that a source must have for it to be detected, we first define a detection threshold and then compute the probabilities of detecting sources of various intensities at the given threshold. The intensity that corresponds to the specified Type II error probability defines that minimum intensity and is identified as the upper limit. Thus, an upper limit is a characteristic of the detection procedure rather than the strength of any particular source. It should not be confused with confidence intervals or other estimates of source intensity. This is particularly important given the large number of catalogs that are being generated from increasingly sensitive surveys. We discuss, with examples, the differences between these upper limits and confidence bounds. Both measures are useful quantities that should be reported in order to extract the most science from catalogs, though they answer different statistical questions: an upper bound describes an inference range on the source intensity, while an upper limit calibrates the detection process. We provide a recipe for computing upper

  4. Joint US Navy/US Air Force climatic study of the upper atmosphere. Volume 1: January

    Science.gov (United States)

    Changery, Michael J.; Williams, Claude N.; Dickenson, Michael L.; Wallace, Brian L.

    1989-07-01

    The upper atmosphere was studied based on 1980 to 1985 twice daily gridded analyses produced by the European Centre for Medium Range Weather Forecasts. This volume is for the month of January. Included are global analyses of: (1) Mean temperature standard deviation; (2) Mean geopotential height standard deviation; (3) Mean density standard deviation; (4) Mean density standard deviation (all for 13 levels - 1000, 850, 700, 500, 400, 300, 250, 200, 150, 100, 70, 50, 30 mb); (5) Mean dew point standard deviation for the 13 levels; and (6) Jet stream at levels 500 through 30 mb. Also included are global 5 degree grid point wind roses for the 13 pressure levels.

  5. Laparoscopic upper pole heminephroureterectomy in children: Seven-year experience

    Directory of Open Access Journals (Sweden)

    Antonio Marte

    2015-01-01

    Full Text Available Background: Minimally invasive surgery is the current approach to perform heminephroureterectomy (HN in children. This can be obtained through a transperitoneal (TP or a retroperitoneal approach. Here, we report our experience using a TP approach. Materials and Methods: From 2005 to 2014, 22 TP laparoscopic upper poles HN were performed at our institution. There were nine girls and 13 boys aged between 20 months and 6 years (mean age 3.9. Eight patients were diagnosed prenatally, 17 patients presented with urinary tract infection (UTI and three with vomiting and failure to thrive. The indication for HN was reflux nephropathy and UTI in non-functioning upper pole in 19 patients and cystic dysplasia in 1 patient. The surgical technique involved the following steps: Cystoscopic recognition; positioning of 3-4 trocar (right HN; identification of the kidney (detachment of the colon; isolation and low ligation of the dilated ureter; decrossing from renal vessels; section of the parenchyma by LigaSure; haemostasis with clips and LigaSure; drain. Results: The mean operative time was 154 min (range: 81-220 min. All patients were discharged from the 2 nd to 4 th day. Neither major complication nor conversion was recorded. 1 patient presented leakage of urine for 7 days from the drainage which resolved spontaneously. At ultrasound follow-up, 5 patients showed a secondary perirenal cyst, 2-5 cm diameter that resolved spontaneously. Conclusion: The results indicate that laparoscopic upper pole heminephrectomy is the treatment of choice in cases of non-functioning dilated lower segments of duplicated kidneys. The use of laparoscopic approach offers a good working space, a good visual control of the vessels and allows a very low isolation of the ureteral stump which counterbalance the peritoneal violation.

  6. Upper atmospheric gravity wave details revealed in nightglow satellite imagery

    Science.gov (United States)

    Miller, Steven D.; Straka, William C.; Yue, Jia; Smith, Steven M.; Alexander, M. Joan; Hoffmann, Lars; Setvák, Martin; Partain, Philip T.

    2015-01-01

    Gravity waves (disturbances to the density structure of the atmosphere whose restoring forces are gravity and buoyancy) comprise the principal form of energy exchange between the lower and upper atmosphere. Wave breaking drives the mean upper atmospheric circulation, determining boundary conditions to stratospheric processes, which in turn influence tropospheric weather and climate patterns on various spatial and temporal scales. Despite their recognized importance, very little is known about upper-level gravity wave characteristics. The knowledge gap is mainly due to lack of global, high-resolution observations from currently available satellite observing systems. Consequently, representations of wave-related processes in global models are crude, highly parameterized, and poorly constrained, limiting the description of various processes influenced by them. Here we highlight, through a series of examples, the unanticipated ability of the Day/Night Band (DNB) on the NOAA/NASA Suomi National Polar-orbiting Partnership environmental satellite to resolve gravity structures near the mesopause via nightglow emissions at unprecedented subkilometric detail. On moonless nights, the Day/Night Band observations provide all-weather viewing of waves as they modulate the nightglow layer located near the mesopause (∼90 km above mean sea level). These waves are launched by a variety of physical mechanisms, ranging from orography to convection, intensifying fronts, and even seismic and volcanic events. Cross-referencing the Day/Night Band imagery with conventional thermal infrared imagery also available helps to discern nightglow structures and in some cases to attribute their sources. The capability stands to advance our basic understanding of a critical yet poorly constrained driver of the atmospheric circulation. PMID:26630004

  7. Pediatric and staff dose evaluation in fluoroscopy upper gastrointestinal series

    Energy Technology Data Exchange (ETDEWEB)

    Filipov, Danielle; Nascimento, Eduarda X. do; Lacerda, Camila M., E-mail: diilipov@utfpr.edu.br [Universidade Tecnologica Federal do Parana (UFTPR), Curitiba, PR (Brazil); Schelin, Hugo R.; Ledesma, Jorge A.; Denyak, Valeriy; Legnani, Adriano, E-mail: ledesmajorgealberto@gmail.com [Instituto de Pesquisa Pele Pequeno Principe, Curitiba, PR (Brazil)

    2014-07-01

    Fluoroscopy upper GI series are widely used for the diagnosis of gastroesophageal reflux disease in children. Pediatric radiological procedures bring concern due to the high life expectancy and radiosensitivity on children, as well as the risks to the exposed staff Important studies present the mean KAP values on patients and the European Commission (EC) recommends specific techniques for these procedures. For the occupational expositions, staffs doses must be within the annual limit, according to the CNEN 3.01. Based on those data, the aims of the current study are: analyzing the upper GI procedure; determining the KAP on the patient and estimating the annual equivalent dose on the staff's crystalline. LiF :Mg,Ti TLDs were positioned on the patient upper chest center, so that the entrance surface air kerma could be determined. The field size on the patient s surface and the kerma were multiplied so that the KAP was obtained. LiF:Mg,Cu,P dosimeters were used to estimate the equivalent dose on the staff s crystalline. The results showed discrepancy in the kVp range and in the exposure time when compared to the EC data. The mean KAP values for the 0-1,1-3 and 3-10 years old patients were, respectively: 102 ± 19 cGy.cm2, 142 ± 25 cGy.cm2 and 323 ± 39 cGy.cm2; which are higher than the KAPs presented in the studies used for comparison. The estimated annual equivalent dose in the staff s crystalline would be approximately 85% higher than the limit set by the CNEN. Analyzing the data, it becomes clear that an optimization implementation is necessary in order to reduce the radiation levels. (author)

  8. Pediatric and staff dose evaluation in fluoroscopy upper gastrointestinal series

    International Nuclear Information System (INIS)

    Filipov, Danielle; Nascimento, Eduarda X. do; Lacerda, Camila M.; Schelin, Hugo R.; Ledesma, Jorge A.; Denyak, Valeriy; Legnani, Adriano

    2014-01-01

    Fluoroscopy upper GI series are widely used for the diagnosis of gastroesophageal reflux disease in children. Pediatric radiological procedures bring concern due to the high life expectancy and radiosensitivity on children, as well as the risks to the exposed staff Important studies present the mean KAP values on patients and the European Commission (EC) recommends specific techniques for these procedures. For the occupational expositions, staffs doses must be within the annual limit, according to the CNEN 3.01. Based on those data, the aims of the current study are: analyzing the upper GI procedure; determining the KAP on the patient and estimating the annual equivalent dose on the staff's crystalline. LiF :Mg,Ti TLDs were positioned on the patient upper chest center, so that the entrance surface air kerma could be determined. The field size on the patient s surface and the kerma were multiplied so that the KAP was obtained. LiF:Mg,Cu,P dosimeters were used to estimate the equivalent dose on the staff s crystalline. The results showed discrepancy in the kVp range and in the exposure time when compared to the EC data. The mean KAP values for the 0-1,1-3 and 3-10 years old patients were, respectively: 102 ± 19 cGy.cm2, 142 ± 25 cGy.cm2 and 323 ± 39 cGy.cm2; which are higher than the KAPs presented in the studies used for comparison. The estimated annual equivalent dose in the staff s crystalline would be approximately 85% higher than the limit set by the CNEN. Analyzing the data, it becomes clear that an optimization implementation is necessary in order to reduce the radiation levels. (author)

  9. INFLUENCE OF TWO DIFFERENT REST INTERVAL LENGTHS IN RESISTANCE TRAINING SESSIONS FOR UPPER AND LOWER BODY

    Directory of Open Access Journals (Sweden)

    Gilmar Senna

    2009-06-01

    Full Text Available Rest intervals between sets appear to be an important variable that can directly affect training volume and fatigue. The purpose of the present study was to compare the influence of two and five-minute rest intervals on the number of repetitions per set, per exercise and total repetitions in resistance training sessions. Fourteen trained men (23.0 ± 2. 2 yrs; 74.9 ± 4.1 kg; 1.75 ± 0.03 m completed three sets per exercise, with 10RM load in four training sessions. Two sessions involved lower body exercises (leg press, leg extension and leg curl, with two-minute (SEQA and with five-minute interval (SEQB. The other two sessions involved upper body exercises (bench press, pec-deck and triceps pulley, with two (SEQC and five-minute intervals (SEQD. For two-minute, five of six exercises presented reductions in the second set, compared with the first set, and for the third set compared with the first and second sets. For five-minute, three of the six exercises presented reductions in the third set, compared with the first sets, and two of the six for the third set, compared with the second sets. The total number of repetitions in SEQA (66.7 ± 4.9 was significantly smaller than in SEQB (80.9 ± 6.9. Similarly, the total repetitions was significantly lower in SEQC (71.1 ± 4.7 compared with SEQD (83.7 ± 6.1. The results indicate that the training session performance is reduced by shorter intervals, being the initial exercises less affected during the progression of the sets

  10. Water poverty in upper Bagmati River Basin in Nepal

    Directory of Open Access Journals (Sweden)

    Jay Krishna Thakur

    2017-04-01

    The WPI was calculated for the upper Bagmati river Basin together with High–Medium–Low category scale and interpretations. WPI intensity scale depicts Sundarijal and Lubhu are in a range of very low water poverty, which means the water situation is better in these two areas. Daman region has a medium level, meaning this region is located into poor-accessible water zone. Kathmandu, Sankhu and Thankot have a low to medium low WPI, what characterize them as neutral. WPI can be used as an effective tool in integrated water resources management and water use master plan for meeting sustainable development goals. Based on the observation, the water agencies required to focus over water-poverty interface, water for sanitation, hygiene and health, water for production and employment generation, sustainable environmental management, gender equality, and water rights.

  11. New Parallaxes for the Upper Scorpius OB Association

    Science.gov (United States)

    Donaldson, J. K.; Weinberger, A. J.; Gagné, J.; Boss, A. P.; Keiser, S. A.

    2017-11-01

    Upper Scorpius is a subgroup of the nearest OB association, Scorpius-Centaurus. Its young age makes it an important association to study star and planet formation. We present parallaxes to 52 low-mass stars in Upper Scorpius, 28 of which have full kinematics. We measure ages of the individual stars by combining our measured parallaxes with pre-main-sequence evolutionary tracks. We find a significant difference in the ages of stars with and without circumstellar disks. The stars without disks have a mean age of 4.9 ± 0.8 Myr and those with disks have an older mean age of 8.2 ± 0.9 Myr. This somewhat counterintuitive result suggests that evolutionary effects in young stars can dominate their apparent ages. We also attempt to use the 28 stars with full kinematics (I.e., proper motion, radial velocity (RV), and parallax) to trace the stars back in time to their original birthplace to obtain a trackback age. As expected, given the large measurement uncertainties on available RV measurements, we find that measurement uncertainties alone cause the group to diverge after a few Myr.

  12. CRPS of the upper or lower extremity: surgical treatment outcomes

    Directory of Open Access Journals (Sweden)

    Rosson Gedge D

    2009-02-01

    Full Text Available Abstract The hypothesis is explored that CRPS I (the "new" RSD persists due to undiagnosed injured joint afferents, and/or cutaneous neuromas, and/or nerve compressions, and is, therefore, a misdiagnosed form of CRPS II (the "new" causalgia. An IRB-approved, retrospective chart review on a series of 100 consecutive patients with "RSD" identified 40 upper and 30 lower extremity patients for surgery based upon their history, physical examination, neurosensory testing, and nerve blocks. Based upon decreased pain medication usage and recovery of function, outcome in the upper extremity, at a mean of 27.9 months follow-up (range of 9 to 81 months, gave results that were excellent in 40% (16 of 40 patients, good in 40% (16 of 40 patients and failure 20% (8 of 40 patients. In the lower extremity, at a mean of 23.0 months follow-up (range of 9 to 69 months the results were excellent in 47% (14 of 30 patients, good in 33% (10 of 30 patients and failure 20% (6 of 30 patients. It is concluded that most patients referred with a diagnosis of CRPS I have continuing pain input from injured joint or cutaneous afferents, and/or nerve compressions, and, therefore, similar to a patient with CRPS II, they can be treated successfully with an appropriate peripheral nerve surgical strategy.

  13. 46 CFR 177.500 - Means of escape.

    Science.gov (United States)

    2010-10-01

    ... cinemas, and public accommodation spaces as defined in § 175.400 of this subchapter, except overnight accommodation spaces: One person may be permitted for each 0.9 square meters (10 square feet) of deck area. In..., or the equivalent, of more than 6.1 meters (20 feet) in length is prohibited. (h) Each door, hatch...

  14. DNSC08 mean sea surface and mean dynamic topography models

    DEFF Research Database (Denmark)

    Andersen, Ole Baltazar; Knudsen, Per

    2009-01-01

    -2004. It is the first global MSS without a polar gap including all of the Arctic Ocean by including laser altimetry from the ICESat mission. The mean dynamic topography (MDT) is the quantity that bridges the geoid and the mean sea surface constraining large-scale ocean circulation. Here we present a new high...

  15. Meaning identification and meaning selection for general language monolingual dictionaries

    DEFF Research Database (Denmark)

    Bergenholtz, Henning; Agerbo, Heidi

    2014-01-01

    The traditional way for lexicographers to deal with polysemy in dictionaries is by applying the terms lumping and splitting. We will not follow this tradition. Instead, we argue that the identification and selection of meaning items (= polysems) should be treated in the same way as the identifica......The traditional way for lexicographers to deal with polysemy in dictionaries is by applying the terms lumping and splitting. We will not follow this tradition. Instead, we argue that the identification and selection of meaning items (= polysems) should be treated in the same way...... to references in the world (in this contribution called things), followed by a formulation of the identified meaning items which can be used for reception situations. Not always – as in the case of lemma selection – will all the identified meaning items be included in the dictionary. The selection of identified...... meaning items will depend on the genuine purpose of the dictionary....

  16. Some Elementary Aspects of Means

    Directory of Open Access Journals (Sweden)

    Mowaffaq Hajja

    2013-01-01

    Full Text Available We raise several elementary questions pertaining to various aspects of means. These questions refer to both known and newly introduced families of means, and include questions of characterizations of certain families, relations among certain families, comparability among the members of certain families, and concordance of certain sequences of means. They also include questions about internality tests for certain mean-looking functions and about certain triangle centers viewed as means of the vertices. The questions are accessible to people with no background in means, and it is also expected that these people can seriously investigate, and contribute to the solutions of, these problems. The solutions are expected to require no more than simple tools from analysis, algebra, functional equations, and geometry.

  17. Upper limb treatment technigues for stroke survivors

    Directory of Open Access Journals (Sweden)

    Martyna Kornet

    2017-03-01

    It was considered that the most important elements of the treatment used in the rehabilitation of the paretic upper limb are: exercise matching the anti-spasm pattern, maintaining appropriate position for exercise that provide an approximation of the shoulder joint and the use of cross-facilitation. The study indicates that the treatment of a post stroke upper limb should be based on the: physiotherapy, kinesiotherapy and specific positioning - all of them corresponding to a given stage of the disease. The work also presents the most frequently used methods, especially highlighting: the Prorioceptive Neuromuscular Facilitation (PNF, Bobath, Brunnstrom, CIMT and OIT. It was also shown that in order to enhance the effects of a post-stroke upper limb rehabilitation, it should be extended by modern methods such as Mirror Therapy, Virtual Reality or Robot-assisted Therapy.

  18. Upper entropy axioms and lower entropy axioms

    International Nuclear Information System (INIS)

    Guo, Jin-Li; Suo, Qi

    2015-01-01

    The paper suggests the concepts of an upper entropy and a lower entropy. We propose a new axiomatic definition, namely, upper entropy axioms, inspired by axioms of metric spaces, and also formulate lower entropy axioms. We also develop weak upper entropy axioms and weak lower entropy axioms. Their conditions are weaker than those of Shannon–Khinchin axioms and Tsallis axioms, while these conditions are stronger than those of the axiomatics based on the first three Shannon–Khinchin axioms. The subadditivity and strong subadditivity of entropy are obtained in the new axiomatics. Tsallis statistics is a special case of satisfying our axioms. Moreover, different forms of information measures, such as Shannon entropy, Daroczy entropy, Tsallis entropy and other entropies, can be unified under the same axiomatics

  19. Upper mantle flow in the western Mediterranean

    Energy Technology Data Exchange (ETDEWEB)

    Panza, G F [Dipartimento di Scienze della Terra, Universita degli Studi di Trieste, Trieste (Italy) and Abdus Salam International Centre for Theoretical Physics, Trieste (Italy); Raykova, R [Geophysical Institute of BAS, Sofia (Bulgaria) and Istituto Nazionale di Geofisica e Vulcanologia, Sezione Bologna, Bologna (Italy); Carminati, E; Doglioni, C [Dipartimento di Scienze della Terra, Universita degli Studi di Trieste, Trieste (Italy)

    2006-07-15

    Two cross-sections of the western Mediterranean Neogene-to-present backarc basin are presented, in which geological and geophysical data of the Transmed project are tied to a new shear-wave tomography. Major results are i) the presence of a well stratified upper mantle beneath the older African continent, with a marked low-velocity layer between 130-200 km of depth; ii) the dilution of this layer within the younger western Mediterranean backarc basin to the north, and iii) the easterly raising of a shallower low-velocity layer from about 140 km to about 30 km in the Tyrrhenian active part of the backarc basin. These findings suggest upper mantle circulation in the western Mediterranean backarc basin, mostly easterly-directed and affecting the boundary between upper asthenosphere (LVZ) and lower asthenosphere, which undulates between about 180 km and 280 km. (author)

  20. Upper mantle flow in the western Mediterranean

    International Nuclear Information System (INIS)

    Panza, G.F.; Raykova, R.; Carminati, E.; Doglioni, C.

    2006-07-01

    Two cross-sections of the western Mediterranean Neogene-to-present backarc basin are presented, in which geological and geophysical data of the Transmed project are tied to a new shear-wave tomography. Major results are i) the presence of a well stratified upper mantle beneath the older African continent, with a marked low-velocity layer between 130-200 km of depth; ii) the dilution of this layer within the younger western Mediterranean backarc basin to the north, and iii) the easterly raising of a shallower low-velocity layer from about 140 km to about 30 km in the Tyrrhenian active part of the backarc basin. These findings suggest upper mantle circulation in the western Mediterranean backarc basin, mostly easterly-directed and affecting the boundary between upper asthenosphere (LVZ) and lower asthenosphere, which undulates between about 180 km and 280 km. (author)

  1. A Boundary Property for Upper Domination

    KAUST Repository

    AbouEisha, Hassan M.

    2016-08-08

    An upper dominating set in a graph is a minimal (with respect to set inclusion) dominating set of maximum cardinality.The problem of finding an upper dominating set is generally NP-hard, but can be solved in polynomial time in some restricted graph classes, such as P4-free graphs or 2K2-free graphs.For classes defined by finitely many forbidden induced subgraphs, the boundary separating difficult instances of the problem from polynomially solvable ones consists of the so called boundary classes.However, none of such classes has been identified so far for the upper dominating set problem.In the present paper, we discover the first boundary class for this problem.

  2. Transfusion strategy for acute upper gastrointestinal bleeding.

    Science.gov (United States)

    Handel, James; Lang, Eddy

    2015-09-01

    Clinical question Does a hemoglobin transfusion threshold of 70 g/L yield better patient outcomes than a threshold of 90 g/L in patients with acute upper gastrointestinal bleeding? Article chosen Villanueva C, Colomo A, Bosch A, et al. Transfusion strategies for acute upper gastrointestinal bleeding. N Engl J Med 2013;368(1):11-21. Study objectives The authors of this study measured mortality, from any cause, within the first 45 days, in patients with acute upper gastrointestinal bleeding, who were managed with a hemoglobin threshold for red cell transfusion of either 70 g/L or 90 g/L. The secondary outcome measures included rate of further bleeding and rate of adverse events.

  3. Hypnosis and upper digestive function and disease

    Science.gov (United States)

    Chiarioni, Giuseppe; Palsson, Olafur S; Whitehead, William E

    2008-01-01

    Hypnosis is a therapeutic technique that primarily involves attentive receptive concentration. Even though a small number of health professionals are trained in hypnosis and lingering myths and misconceptions associated with this method have hampered its widespread use to treat medical conditions, hypnotherapy has gained relevance as an effective treatment for irritable bowel syndrome not responsive to standard care. More recently, a few studies have addressed the potential influence of hypnosis on upper digestive function and disease. This paper reviews the efficacy of hypnosis in the modulation of upper digestive motor and secretory function. The present evidence of the effectiveness of hypnotherapy as a treatment for functional and organic diseases of the upper bowel is also summarized, coupled with a discussion of potential mechanisms of its therapeutic action. PMID:19009639

  4. Subspace K-means clustering.

    Science.gov (United States)

    Timmerman, Marieke E; Ceulemans, Eva; De Roover, Kim; Van Leeuwen, Karla

    2013-12-01

    To achieve an insightful clustering of multivariate data, we propose subspace K-means. Its central idea is to model the centroids and cluster residuals in reduced spaces, which allows for dealing with a wide range of cluster types and yields rich interpretations of the clusters. We review the existing related clustering methods, including deterministic, stochastic, and unsupervised learning approaches. To evaluate subspace K-means, we performed a comparative simulation study, in which we manipulated the overlap of subspaces, the between-cluster variance, and the error variance. The study shows that the subspace K-means algorithm is sensitive to local minima but that the problem can be reasonably dealt with by using partitions of various cluster procedures as a starting point for the algorithm. Subspace K-means performs very well in recovering the true clustering across all conditions considered and appears to be superior to its competitor methods: K-means, reduced K-means, factorial K-means, mixtures of factor analyzers (MFA), and MCLUST. The best competitor method, MFA, showed a performance similar to that of subspace K-means in easy conditions but deteriorated in more difficult ones. Using data from a study on parental behavior, we show that subspace K-means analysis provides a rich insight into the cluster characteristics, in terms of both the relative positions of the clusters (via the centroids) and the shape of the clusters (via the within-cluster residuals).

  5. Rolling Deck to Repository (R2R): Products and Services for the U.S. Research Fleet Community

    Science.gov (United States)

    Arko, R. A.; Carbotte, S. M.; Chandler, C. L.; Smith, S. R.; Stocks, K. I.

    2016-02-01

    The Rolling Deck to Repository (R2R) program is working to ensure open access to environmental sensor data routinely acquired by the U.S. academic research fleet. Currently 25 vessels deliver 7 TB/year of data to R2R from a suite of geophysical, oceanographic, meteorological, and navigational sensors on over 400 cruises worldwide. R2R ensures these data are preserved in trusted repositories, discoverable via standard protocols, and adequately documented for reuse. R2R has recently expanded to include the vessels Sikuliaq, operated by the University of Alaska; Falkor, operated by the Schmidt Ocean Institute; and Ronald H. Brown and Okeanos Explorer, operated by NOAA. R2R maintains a master catalog of U.S. research cruises, currently holding over 4,670 expeditions including vessel and cruise identifiers, start/end dates and ports, project titles and funding awards, science parties, dataset inventories with instrument types and file formats, data quality assessments, and links to related content at other repositories. Standard post-field cruise products are published including shiptrack navigation, near-real-time MET/TSG data, underway geophysical profiles, and CTD profiles. Software tools available to users include the R2R Event Logger and the R2R Nav Manager. A Digital Object Identifier (DOI) is published for each cruise, original field sensor dataset, standard post-field product, and document (e.g. cruise report) submitted by the science party. Scientists are linked to personal identifiers such as ORCIDs where available. Using standard identifiers such as DOIs and ORCIDs facilitates linking with journal publications and generation of citation metrics. R2R collaborates in the Ocean Data Interoperability Platform (ODIP) to strengthen links among regional and national data systems, populates U.S. cruises in the POGO global catalog, and is working toward membership in the DataONE alliance. It is a lead partner in the EarthCube GeoLink project, developing Semantic Web

  6. Rolling Deck to Repository (R2R): A "Linked Data" Approach for the U.S. Academic Research Fleet

    Science.gov (United States)

    Arko, R. A.; Chandler, C. L.; Clark, P. D.; Milan, A.; Mize, J.

    2011-12-01

    The U.S. academic research fleet is an essential mobile observing platform for ocean science. The NSF-funded Rolling Deck to Repository (R2R) program is working with the fleet community to routinely document, assess, and preserve data from the underway sensor systems on each vessel. The R2R facility maintains a master catalog of vessels, instrument systems, operating institutions, cruises, personnel, and data sets. In less than two years, the catalog has grown to over 2,000 cruises including unique identifiers for vessel deployments, project titles, chief scientists, dates, ports, survey targets, and navigation tracks. This master catalog is of great value to peer data systems, ranging from large national data centers to small disciplinary data offices, as an aid in organizing, extending, and quality controlling their own collections and finding related data from authoritative sources. R2R breaks with the tradition of stovepipe portals built around complex search interfaces tightly bound to backend databases. Instead, we have adopted a Linked Data approach to publish our catalog content, based on the W3C Resource Description Framework (RDF) and Uniform Resource Identifiers (URIs). Our data model is published as a collection of W3C Simple Knowledge Organization System (SKOS) concepts, mapped to partner vocabularies such as those developed by the Global Change Master Directory (GCMD) and the pan-European SeaDataNet partnership, and our catalog content is published as collections of RDF resources with globally unique and persistent identifiers. The combination of exposing our data model, mapping local terms to community-wide vocabularies, and using reliable identifiers improves interoperability and reduces ambiguity. R2R's metric of success is the degree to which peer data systems routinely harvest and reuse our content. R2R is working collaboratively with the NOAA National Data Centers and the NSF-funded Biological and Chemical Oceanography Data Management Office

  7. Rolling Deck to Repository (R2R): A "Linked Data" Approach for the U.S. Academic Research Fleet

    Science.gov (United States)

    Arko, R.; Chandler, C.; Clark, P.; Milan, A.; Mize, J.

    2012-04-01

    The Rolling Deck to Repository (R2R; http://rvdata.us/) program is developing infrastructure to routinely document, assess, and preserve the underway sensor data from U.S. academic research vessels. The R2R master catalog of vessels, instrument systems, operating institutions, cruises, personnel, data sets, event logs, and field reports has grown to over 2,200 cruises in less than two years, and is now accessible via Web services. This catalog is of great value to peer data systems, ranging from large inter/national data centers to small disciplinary data offices, as an aid in quality controlling their own collections and finding related data from authoritative sources. R2R breaks with the tradition of stovepipe portals built around complex search interfaces tightly bound to backend databases. Instead, we have adopted a Linked Data approach to publish our catalog content, based on the W3C Resource Description Framework (RDF) and Uniform Resource Identifiers (URIs). Our data model is published as a collection of W3C Simple Knowledge Organization System (SKOS) concepts, mapped to partner vocabularies such as those developed by the Global Change Master Directory (GCMD) and the pan-European SeaDataNet partnership, and our catalog content is published as collections of RDF resources with globally unique and persistent identifiers. The combination of exposing our data model, mapping local terms to community-wide vocabularies, and using reliable identifiers improves interoperability and reduces ambiguity. R2R's metric of success is the degree to which peer data systems harvest and reuse our content. R2R is working collaboratively with the NOAA National Data Centers and the NSF-funded Biological and Chemical Oceanography Data Management Office (BCO-DMO) on a range of Linked Data pilot applications, including production of ISO-compliant metadata and deployment of a RDF Query Language (SPARQL) interface. Our objective is to support a distributed, loosely federated network of

  8. A STUDY ON ENDOSCOPIC EVALUATION OF UPPER GASTROINTESTINAL BLEEDING

    Directory of Open Access Journals (Sweden)

    Pranaya Kumar

    2016-03-01

    Full Text Available CONTEXT Upper gastrointestinal bleeding (UGIB is one of the commonest gastrointestinal emergencies encountered by clinicians. Peptic ulcers are the most common cause of UGIB. Endoscopy has become the preferred method for diagnosis in patients with acute UGIB. This study is done in a diagnostic upper gastrointestinal endoscopy (UGIE setup of a tertiary care hospital to ascertain the causes of UGIB prevalent in this part of our country which might differ from other studies. AIM To ascertain prevalent causes of UGIB in patients of this part of India admitted to a Govt. Tertiary Hospital with a provisional diagnosis of UGIB. METHOD One hundred consecutive patients with UGIB were subjected to UGIE to find out the aetiology. The clinical profile and endoscopic findings were analysed and compared with the data on UGIB from other studies. RESULTS The mean age of patients was 47.03 years with male: female ratio of 2.33:1. 58% of patients were first time bleeders. Majority of patients presented with melaena. Visualisation of active bleeding achieved to 85.7% when endoscopy was done within first 24 hrs. The commonest cause of UGIB was duodenal ulcer (DU which accounted for 41% cases. Gastric ulcer was responsible in 13% of cases. Portal hypertension was responsible for bleed in only 13%. Neoplasms accounted for 25% of cases. Other less common causes were erosive gastritis (3%, gastric polyp (3%, Mallory-Weiss tear (1%, and Dieulafoy’s lesion (1%. Among bleeding peptic ulcers, 27.8% of cases were classified as Forrest IIa and 20.4% in Forrest IIb & IIc each. Acid peptic disease was past history elicited in majority (33% followed by NSAID (26% and alcohol (26%. CONCLUSION The present study has diagnosed various causes of upper gastrointestinal bleeding in this part of country. The incidence of gastric carcinoma as a cause of upper gastrointestinal bleeding is significantly high compared to those in other studies. UGI endoscopy should be done in every case

  9. New upper limits on the local metagalactic ionizing radiation density

    Science.gov (United States)

    Vogel, Stuart N.; Weymann, Ray; Rauch, Michael; Hamilton, Tom

    1995-01-01

    We have obtained H-alpha observations with the Maryland-Caltech Fabry-Perot Spectrometer attached to the Cassegrain focus of the 1.5 m telescope at Palomer Observatory in order to set limits on the number of ionizing photons from the local metagalactic radiation field. We have observed the SW component of the Haynes-Giovanelli cloud H I 1225+01, an intergalactic cloud which should be optimum for measuring the metagalactic flux because it is nearly opaque to ionizing photons, it does not appear to be significantly shielded from the metagalactic radiation field, and the limits on embedded or nearby ionizing sources are unusually low. For the area of the cloud with an H I column density greater than 10(exp 19)/sq cm we set a 2 sigma limit of 1.1 x 10(exp -19) ergs/sq cm/s/sq arcsec (20 mR) for the surface brightness of diffuse H-alpha. This implies a 2 sigma upper limit on the incident one-sided ionizing flux of Phi(sub ex) is less than 3 x 10(exp 4)/sq cm/s. For a radiation field of the form J(sub nu) is approximately nu(exp -1.4), this yields a firm 2 sigma upper limit on the local metagalactic photoionization rate of Gamma is less than 2 x 10(exp -13)/s, and an upper limit for the radiation field J(sub nu) at the Lyman limit of J(sub nu0) is less than 8 x 10(exp -23) ergs/sq cm/Hz/sr. We discuss previous efforts to constrain the metagalactic ionizing flux using H-alpha surface brightness observations and also other methods, and conclude that our result places the firmest upper limit on this flux. We also observed the 7 min diameter region centered on 3C 273 in which H-alpha emission at a velocity of approximately 1700 km/s was initially reported by Williams and Schommer. In agreement with T. B. Williams (private communication) we find the initial detection was spurious. We obtain a 2 sigma upper limit of 1.8 x 10(exp -19) ergs/sq cm/s/sq arcsec (32 mR) for the mean surface brightness of diffuse H-alpha, about a factor of 6 below the published value.

  10. Membraneous stenosis of the upper oesophagus ('webs')

    International Nuclear Information System (INIS)

    Koch, H.L.; Kurtz, B.

    1981-01-01

    Webs of the upper oesophagus are sail-like mucosal folds of unknown aetiology. Small, transverse webs on the anterior wall of the oesophagus are not uncommon incidental findings which are easily overlooked on routine examination. Extensive, circular membranes in the upper oesophagus, on the other hand, are rare; these may lead to severe difficulty with swallowing and may be associated with regurgitation. One example of a transverse, and three cases of circular webs are described, which caused stenosis and dysphagia and which, in some cases, were multiple. The aetiology is discussed. (orig.) [de

  11. Information Literacy in the Upper Secondary School

    DEFF Research Database (Denmark)

    Holm, Claus; Schreiber, Trine; Tønnesen, Pia Hvid

    The discussion paper is a publication from the project Information Literacy in the Upper Secondary School. The project is a collaboration between the National Library of Education at the Danish School of Education, Aarhus University, and the Royal School of Library and Information Science....... The project is funded by Denmark's Electronic Research Library (DEFF). The discussion paper is published in connection with the conference Information Literacy in the Upper Secondary School on 22 April 2010. See video streaming from the conference etc. at www.dpu.dk/info....

  12. Collaborative Tools in Upper Secondary School - Why?

    DEFF Research Database (Denmark)

    Mathiasen, Helle; Degn, Hans-Peter; Bech, Christian Winther

    2013-01-01

    The paper will discuss potentials of digital media to support student engagement and student production in Danish upper secondary education with a specific focus on group work and collaboration. With the latest school reform, upper secondary education in Denmark has experienced an increased focus...... on the system theoretical approach will be described. Third, the findings from the qualitative, and quantitative studies will be presented. The paper concludes that the study demonstrates changes in the way group work is organised by the students using digital media, and a tendency to develop student engagement...

  13. Forest Certification and Country of Origin: Choice Experiment Analysis of Outdoor Decking Material Selection in E-Commerce Market in Finland

    Directory of Open Access Journals (Sweden)

    Jani Holopainen

    2017-11-01

    Full Text Available Since the early 1990s, there has been hope that the uptake of certified forest products would ensure more sustainable forest management and also deliver business benefits along the value chain. Our study applies a Discrete Choice Experiment (DCE to model an e-commerce purchase in the case of multiple products with various attribute and certification combinations in the Finnish retail outdoor decking material market. We received 2772 responses from 231 participants in an online survey. Applying conditional logit and latent class models, we were able to assess the relative importance of attributes, identify various consumer segments, and simulate various scenarios for communicating the certification and origin of forest products and competing materials. Our results show that the most important attribute for consumer decision-making was the outdoor decking material followed by price, origin, and certification. Some consumer segments showed a habit of only choosing certain materials or domestic products, while paying less attention to other product attributes. Simulations for an e-commerce purchase situation also implied that communications concerning intangible product attributes, such as domestic origin and environmental certifications, could be used in the brand building of the forest sector to gain competitive advantage and increased market shares over other sectors. The results suggest that the conventional and constantly developing e-commerce marketing tools should be harnessed also in forest product and more general environmental marketing.

  14. The Mean as Balance Point

    Science.gov (United States)

    O'Dell, Robin S.

    2012-01-01

    There are two primary interpretations of the mean: as a leveler of data (Uccellini 1996, pp. 113-114) and as a balance point of a data set. Typically, both interpretations of the mean are ignored in elementary school and middle school curricula. They are replaced with a rote emphasis on calculation using the standard algorithm. When students are…

  15. Mean-field lattice trees

    NARCIS (Netherlands)

    Borgs, C.; Chayes, J.T.; Hofstad, van der R.W.; Slade, G.

    1999-01-01

    We introduce a mean-field model of lattice trees based on embeddings into d of abstract trees having a critical Poisson offspring distribution. This model provides a combinatorial interpretation for the self-consistent mean-field model introduced previously by Derbez and Slade [9], and provides an

  16. Assessment of continuous oil and gas resources in the Middle and Upper Magdalena Basins, Colombia, 2017

    Science.gov (United States)

    Schenk, Christopher J.; Brownfield, Michael E.; Tennyson, Marilyn E.; Le, Phuong A.; Mercier, Tracey J.; Finn, Thomas M.; Hawkins, Sarah J.; Gaswirth, Stephanie B.; Marra, Kristen R.; Klett, Timothy R.; Leathers-Miller, Heidi M.; Woodall, Cheryl A.

    2017-09-22

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean undiscovered, technically recoverable continuous resources of 0.45 billion barrels of oil and 1.0 trillion cubic feet of gas in the Middle and Upper Magdalena Basins, Colombia.

  17. Oil well fire extinguisher having upper and lower external flame retardant-dispersing rings

    International Nuclear Information System (INIS)

    Kim, H.S.

    1992-01-01

    This patent describes an extinguisher system for extinguishing flames from combustible fluid exiting from a pipe. It comprises an elongated tubular extinguisher body disposable over the combustible fluid emitting pipe; valve means mounted in the extinguisher body adjacent the upper outlet end for eliminating the flow of the combustion

  18. A joint analysis of river runoff and meteorological forcing in the Karakoram, upper Indus Basin

    NARCIS (Netherlands)

    Reggiani, P.; Mukhopadhyay, B.; Rientjes, T.H.M.; Khan, A.

    2017-01-01

    Satellite‐geodetic altimetry investigations in the Karakoram have indicated slight mass gain or loss of the glaciers during the early part of 21st century. Equivalent discharge in the upper Indus Basin due to these mass changes has been estimated at 5 to 10% of mean annual flow. However, satellite

  19. SUMS preliminary design and data analysis development. [shuttle upper atmosphere mass spectrometer experiment

    Science.gov (United States)

    Hinson, E. W.

    1981-01-01

    The preliminary analysis and data analysis system development for the shuttle upper atmosphere mass spectrometer (SUMS) experiment are discussed. The SUMS experiment is designed to provide free stream atmospheric density, pressure, temperature, and mean molecular weight for the high altitude, high Mach number region.

  20. Emergency readmission following acute upper gastrointestinal bleeding

    DEFF Research Database (Denmark)

    Strömdahl, Martin; Helgeson, Johan; Kalaitzakis, Evangelos

    2017-01-01

    OBJECTIVE: To assess the occurrence, clinical predictors, and associated mortality of all-cause emergency readmissions after acute upper gastrointestinal bleeding (AUGIB). PATIENTS AND METHODS: All patients with AUGIB from an area of 600 000 inhabitants in Sweden admitted in a single institution...